WorldWideScience

Sample records for exchange materials based

  1. Subscale Water Based Phase Change Material Heat Exchanger Development

    Science.gov (United States)

    Sheth, Rubik; Hansen, Scott

    2016-01-01

    Supplemental heat rejection devices are required in many spacecraft as the radiators are not sized to meet the full heat rejection demand. One means of obtaining additional heat rejection is through the use of phase change material heat exchangers (PCM HX's). PCM HX's utilize phase change to store energy in unfavorable thermal environments (melting) and reject the energy in favorable environments (freezing). Traditionally, wax has been used as a PCM on spacecraft. However, water is an attractive alternative because it is capable of storing about 40% more energy per unit mass due to its higher latent heat of fusion. The significant problem in using water as a PCM is its expansion while freezing, leading to structural integrity concerns when housed in an enclosed heat exchanger volume. Significant investigation and development has taken place over the past five years to understand and overcome the problems associated with water PCM HX's. This paper reports on the final efforts by Johnson Space Center's Thermal Systems Branch to develop a water based PCM HX. The test article developed and reported on is a subscale version of the full-scale water-based PCM HX's constructed by Mezzo Technologies. The subscale unit was designed by applying prior research on freeze front propagation and previous full-scale water PCM HX development. Design modifications to the subscale unit included use of urethane bladder, decreased aspect ratio, perforated protection sheet, and use of additional mid-plates. Testing of the subscale unit was successful and 150 cycles were completed without fail.

  2. Continued Water-Based Phase Change Material Heat Exchanger Development

    Science.gov (United States)

    Hansen, Scott W.; Sheth, Rubik B.; Poynot, Joe; Giglio, Tony; Ungar, Gene K.

    2015-01-01

    In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to meet the full heat rejection demands. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HX's do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development two full-scale, Orion sized water-based PCM HX's were constructed by Mezzo Technologies. These HX's were designed by applying prior research on freeze front propagation to a full-scale design. Design options considered included bladder restraint and clamping mechanisms, bladder manufacturing, tube patterns, fill/drain methods, manifold dimensions, weight optimization, and midplate designs. Two units, Units A and B, were constructed and differed only in their midplate design. Both units failed multiple times during testing. This report highlights learning outcomes from these tests and are applied to a final sub-scale PCM HX which is slated to be tested on the ISS in early 2017.

  3. Water Based Phase Change Material Heat Exchanger Development

    Science.gov (United States)

    Hansen, Scott W.; Sheth, Ribik B.; Atwell, Matt; Cheek, Ann; Agarwal, Muskan; Hong, Steven; Patel, Aashini,; Nguyen, Lisa; Posada, Luciano

    2014-01-01

    In a cyclical heat load environment such as low Lunar orbit, a spacecraft’s radiators are not sized to reject the full heat load requirement. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a “topper” to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HXs do not use a consumable, thereby leading to reduced launch mass and volume requirements. Studies conducted in this paper investigate utilizing water’s high latent heat of formation as a PCM, as opposed to traditional waxes, and corresponding complications surrounding freezing water in an enclosed volume. Work highlighted in this study is primarily visual and includes understanding ice formation, freeze front propagation, and the solidification process of water/ice. Various test coupons were constructed of copper to emulate the interstitial pin configuration (to aid in conduction) of the proposed water PCM HX design. Construction of a prototypic HX was also completed in which a flexible bladder material and interstitial pin configurations were tested. Additionally, a microgravity flight was conducted where three copper test articles were frozen continuously during microgravity and 2-g periods and individual water droplets were frozen during microgravity.

  4. Correlation between charge transfer and exchange coupling in carbon-based magnetic materials

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Anh Tuan, E-mail: tuanna@hus.edu.vn [Faculty of Physics, VNU University of Science, 334 Nguyen Trai, Thanh Xuan, Ha Noi (Viet Nam); Science and Technology Department, Vietnam National University, Hanoi, 144 Xuan Thuy, Cau Giay, Hanoi (Viet Nam); Japan Advanced Institute of Science and Technology, 1-1, Asahidai, Nomi, Ishikawa, 923-1292 Japan (Japan); Nguyen, Van Thanh; Nguyen, Huy Sinh [Faculty of Physics, VNU University of Science, 334 Nguyen Trai, Thanh Xuan, Ha Noi (Viet Nam); Pham, Thi Tuan Anh [Faculty of Physics, VNU University of Science, 334 Nguyen Trai, Thanh Xuan, Ha Noi (Viet Nam); Faculty of Science, College of Hai Duong, Nguyen Thi Due, Hai Duong (Viet Nam); Do, Viet Thang [Faculty of Physics, VNU University of Science, 334 Nguyen Trai, Thanh Xuan, Ha Noi (Viet Nam); Faculty of Science, Haiphong University, 171 Phan Dang Luu, Kien An, Hai Phong (Viet Nam); Dam, Hieu Chi [Japan Advanced Institute of Science and Technology, 1-1, Asahidai, Nomi, Ishikawa, 923-1292 Japan (Japan)

    2015-10-15

    Several forms of carbon-based magnetic materials, i.e. single radicals, radical dimers, and alternating stacks of radicals and diamagnetic molecules, have been investigated using density-functional theory with dispersion correction and full geometry optimization. Our calculated results demonstrate that the C{sub 31}H{sub 15} (R{sub 4}) radical has a spin of ½. However, in its [R{sub 4}]{sub 2} dimer structure, the net spin becomes zero due to antiferromagnetic spin-exchange between radicals. To avoid antiferromagnetic spin-exchange of identical face-to-face radicals, eight alternating stacks, R{sub 4}/D{sub 2m}/R{sub 4} (with m = 3-10), were designed. Our calculated results show that charge transfer (Δn) between R{sub 4} radicals and the diamagnetic molecule D{sub 2m} occurs with a mechanism of spin exchange (J) in stacks. The more electrons that transfer from R{sub 4} to D{sub 2m}, the stronger the ferromagnetic spin-exchange in stacks. In addition, our calculated results show that Δn can be tailored by adjusting the electron affinity (E{sub a}) of D{sub 2m}. The correlation between Δn, E{sub a}, m, and J is discussed. These results give some hints for the design of new ferromagnetic carbon-based materials.

  5. Correlation between charge transfer and exchange coupling in carbon-based magnetic materials

    Directory of Open Access Journals (Sweden)

    Anh Tuan Nguyen

    2015-10-01

    Full Text Available Several forms of carbon-based magnetic materials, i.e. single radicals, radical dimers, and alternating stacks of radicals and diamagnetic molecules, have been investigated using density-functional theory with dispersion correction and full geometry optimization. Our calculated results demonstrate that the C31H15 (R4 radical has a spin of ½. However, in its [R4]2 dimer structure, the net spin becomes zero due to antiferromagnetic spin-exchange between radicals. To avoid antiferromagnetic spin-exchange of identical face-to-face radicals, eight alternating stacks, R4/D2m/R4 (with m = 3-10, were designed. Our calculated results show that charge transfer (Δn between R4 radicals and the diamagnetic molecule D2m occurs with a mechanism of spin exchange (J in stacks. The more electrons that transfer from R4 to D2m, the stronger the ferromagnetic spin-exchange in stacks. In addition, our calculated results show that Δn can be tailored by adjusting the electron affinity (Ea of D2m. The correlation between Δn, Ea, m, and J is discussed. These results give some hints for the design of new ferromagnetic carbon-based materials.

  6. Imidazolium-Based Polymeric Materials as Alkaline Anion-Exchange Fuel Cell Membranes

    Science.gov (United States)

    Narayan, Sri R.; Yen, Shiao-Ping S.; Reddy, Prakash V.; Nair, Nanditha

    2012-01-01

    Polymer electrolyte membranes that conduct hydroxide ions have potential use in fuel cells. A variety of polystyrene-based quaternary ammonium hydroxides have been reported as anion exchange fuel cell membranes. However, the hydrolytic stability and conductivity of the commercially available membranes are not adequate to meet the requirements of fuel cell applications. When compared with commercially available membranes, polystyrene-imidazolium alkaline membrane electrolytes are more stable and more highly conducting. At the time of this reporting, this has been the first such usage for imidazolium-based polymeric materials for fuel cells. Imidazolium salts are known to be electrochemically stable over wide potential ranges. By controlling the relative ratio of imidazolium groups in polystyrene-imidazolium salts, their physiochemical properties could be modulated. Alkaline anion exchange membranes based on polystyrene-imidazolium hydroxide materials have been developed. The first step was to synthesize the poly(styrene-co-(1-((4-vinyl)methyl)-3- methylimidazolium) chloride through a free-radical polymerization. Casting of this material followed by in situ treatment of the membranes with sodium hydroxide solutions provided the corresponding hydroxide salts. Various ratios of the monomers 4-chloromoethylvinylbenzine (CMVB) and vinylbenzine (VB) provided various compositions of the polymer. The preferred material, due to the relative ease of casting the film, and its relatively low hygroscopic nature, was a 2:1 ratio of CMVB to VB. Testing confirmed that at room temperature, the new membranes outperformed commercially available membranes by a large margin. With fuel cells now in use at NASA and in transportation, and with defense potential, any improvement to fuel cell efficiency is a significant development.

  7. A Microwave Thermostatic Reactor for Processing Liquid Materials Based on a Heat-Exchanger.

    Science.gov (United States)

    Zhou, Yongqiang; Zhang, Chun; Xie, Tian; Hong, Tao; Zhu, Huacheng; Yang, Yang; Liu, Changjun; Huang, Kama

    2017-10-08

    Microwaves have been widely used in the treatment of different materials. However, the existing adjustable power thermostatic reactors cannot be used to analyze materials characteristics under microwave effects. In this paper, a microwave thermostatic chemical reactor for processing liquid materials is proposed, by controlling the velocity of coolant based on PLC (programmable logic controller) in different liquid under different constant electric field intensity. A nonpolar coolant (Polydimethylsiloxane), which is completely microwave transparent, is employed to cool the liquid materials. Experiments are performed to measure the liquid temperature using optical fibers, the results show that the precision of temperature control is at the range of ±0.5 °C. Compared with the adjustable power thermostatic control system, the effect of electric field changes on material properties are avoided and it also can be used to detect the properties of liquid materials and special microwave effects.

  8. MatDB Online - A Standards-Based System for Preserving, Managing, and Exchanging Engineering Materials Test Data

    Directory of Open Access Journals (Sweden)

    TSP Austin

    2012-11-01

    Full Text Available With ICT Standards playing a key role in support of research and development in many disciplines, the European Commission Institute for Energy and Transport is keen to promote the development and adoption of ICT Standards for engineering data. In this respect, its MatDB Online facility is a Standards-based system for preserving, managing, and exchanging engineering materials test data. While MatDB Online has evolved over more than 30 years to incorporate the latest innovations in data preservation and exchange, such as XML-based data transfer and data citation using digital object identifiers, it continues to rely on a robust data model developed more than 30 years ago through the joint efforts of the National Research Institute for Metals (the predecessor to NIMS, the National Institute for Materials Science, the European Commission Joint Research Centre, and the National Institute of Standards and Technology. While this data model has endured over many years, there is no corresponding Standard. Similarly, related efforts by the engineering materials community to deliver a Standard representation for engineering materials, such as MatML, have failed to be ratified. In consequence of the continued absence of a Standard representation for engineering materials data, there is no common mechanism for preserving and exchanging materials data and no formal means of maintaining a data model to support advances in materials technology, such as the emergence of nanomaterials. It is for these reasons that the European Commission Institute for Energy and Transport is supporting SERES, a CEN Workshop on Standards for Electronic Reporting in the Engineering Sector. As one of more than thirty organisations supporting the SERES Workshop, the Institute for Energy and Transport will make the MatDB XML schema available as one of several resources that will be taken into consideration when the prenormative Standard for representing engineering materials data is

  9. A New Adsorbent Composite Material Based on Metal Fiber Technology and Its Application in Adsorption Heat Exchangers

    Directory of Open Access Journals (Sweden)

    Ursula Wittstadt

    2015-08-01

    Full Text Available In order to achieve process intensification for adsorption chillers and heat pumps, a new composite material was developed based on sintered aluminum fibers from a melt-extraction process and a dense layer of silico-aluminophosphate (SAPO-34 on the fiber surfaces. The SAPO-34 layer was obtained through a partial support transformation (PST process. Preparation of a composite sample is described and its characteristic pore size distribution and heat conductivity are presented. Water adsorption data obtained under conditions of a large pressure jump are given. In the next step, preparation of the composite was scaled up to larger samples which were fixed on a small adsorption heat exchanger. Adsorption measurements on this heat exchanger element that confirm the achieved process intensification are presented. The specific cooling power for the adsorption step per volume of composite is found to exceed 500 kW/m3 under specified conditions.

  10. Surface oxygen exchange properties of bismuth oxide-based solid electrolytes and electrode materials

    NARCIS (Netherlands)

    Boukamp, Bernard A.; Vinke, I.C.; de Vries, K.J.; Burggraaf, A.J.

    1989-01-01

    The surface oxygen exchange coefficient, ks, has been measured for the solid solution (Bi2O3)0.75(Er2O3)0.25 and (Bi2O3)0.6(Tb2O3)0.4 (abbreviated BE25 and BT40), using gas-phase 18O exchange techniques. The activation enth alpy of ks amounts to ΔE=110 kJ/molforBT40 andΔE=130 kJ/molforBE25. The

  11. Barcoded materials based on photoluminescent hybrid system of lanthanide ions-doped metal organic framework and silica via ion exchange.

    Science.gov (United States)

    Shen, Xiang; Yan, Bing

    2016-04-15

    A multicolored photoluminescent hybrid system based on lanthanide ions-doped metal organic frameworks/silica composite host has potential in display and barcode applications. By controlling the stoichiometry of the lanthanides via cation exchange, proportional various lanthanide ions are successfully introduced into metal organic frameworks, whose emission intensity is correspondingly proportional to its amount. The resulting luminescent barcodes depend on the lanthanide ions ratios and compositions. Subsequently, the lanthanide ions located in the channels of metal organic frameworks are protected from any interaction with the environment after the modification of silica on the surface. The optical and thermal stability of the hybrid materials are improved for technological application. Copyright © 2016 Elsevier Inc. All rights reserved.

  12. Nanomodified polymer materials for regenerative heat exchangers

    Science.gov (United States)

    Shchegolkov, Alexander; Shchegolkov, Alexey; Dyachkova, Tatyana

    2017-11-01

    The paper presents thermophysical properties of nanomodified paraffin mixed with polymers as polyethylene or fluoroplastic, which may be effectively used for the development of heat exchange elements of personal protective equipment. It has been experimentally shown that the heat exchangers based on the nanomodified polymer composites have twofold mass compared to the standard regenerative heat exchanger with comparable dimensions. The best result has been obtained on the basis of composite containing polyethylene and paraffin modified with CNTs, which thermal conductivity is 1.6 times higher than forconventional paraffin. The application of carbon nanostructures as the modifiers of heat storage materials improves cooling efficiency by 14.9-17.9 °C by creating more comfortable conditions for breathing via personal protective equipment.

  13. Radiation effects on ion exchange materials

    Energy Technology Data Exchange (ETDEWEB)

    Gangwer, T.E.; Goldstein, M.; Pillay, K.K.S.

    1977-11-01

    An extensive literature review and data compilation has been completed on the radiation-damage of ion exchange resins. The primary goal of the study has been to review the available literature on ion exchange materials used in, as well as those with potential for use in, the nuclear fuel and waste reprocessing areas. The physical and chemical properties of ion exchangers are reviewed. Experimental parameters useful in characterizing the effects of radiation on synthetic ion exchange resins are identified or defined. In compiling the diverse types of data, an effort was made to present the experimental data or experimentally based parameters in a format that would be useful for inter-comparing radiation effects on resins. When subject to radiation there are various general trends or qualitative effects displayed by the different types of resins. These radiation-trends and effects have been formulated into qualitative statements. The present day level of understanding of the behavior of resins under ionizing radiation is too limited to justify quantitative predictive modeling. The limitations and deficiencies of the literature are discussed and the experimentation needed to achieve quantitative modeling are outlined. 14 figs., 108 references.

  14. Exchanging Description Logic Knowledge Bases

    NARCIS (Netherlands)

    Arenas, M.; Botoeva, E.; Calvanese, D.; Ryzhikov, V.; Sherkhonov, E.

    2012-01-01

    In this paper, we study the problem of exchanging knowledge between a source and a target knowledge base (KB), connected through mappings. Differently from the traditional database exchange setting, which considers only the exchange of data, we are interested in exchanging implicit knowledge. As

  15. Phase Change Material Heat Exchanger Life Test

    Science.gov (United States)

    Lillibridge, Sean; Stephan, Ryan

    2009-01-01

    Low Lunar Orbit (LLO) poses unique thermal challenges for the orbiting space craft, particularly regarding the performance of the radiators. The IR environment of the space craft varies drastically from the light side to the dark side of the moon. The result is a situation where a radiator sized for the maximal heat load in the most adverse situation is subject to freezing on the dark side of the orbit. One solution to this problem is to implement Phase Change Material (PCM) Heat Exchangers. PCM Heat Exchangers act as a "thermal capacitor," storing thermal energy when there is too much being produced by the space craft to reject to space, and then feeding that energy back into the thermal loop when conditions are more favorable. Because they do not use an expendable resource, such as the feed water used by sublimators and evaporators, PCM Heat Exchangers are ideal for long duration LLO missions. In order to validate the performance of PCM Heat Exchangers, a life test is being conducted on four n-Pentadecane, carbon filament heat exchangers. Fluid loop performance, repeatability, and measurement of performance degradation over 2500 melt-freeze cycles will be performed.

  16. Materials Ontology: An Infrastructure for Exchanging Materials Information and Knowledge

    Directory of Open Access Journals (Sweden)

    Toshihiro Ashino

    2010-06-01

    Full Text Available We have rich information resources for materials science and engineering - raw measurement data, computational simulation methods, digitized handbooks, and digital libraries. However, these resources have a wide variety of formats, terminologies, and concepts, which makes it difficult to find appropriate information for materials design, development, and evaluation. One solution to this problem is to integrate these resources into a computer readable concept map, called a domain ontology, which describes concepts and relationships among the concepts in materials science and engineering. This paper describes a trial that constructs a standard of metadata description using ontology language and demonstrates the validity of this construction through data exchange among heterogeneous material databases. "Materials Ontology," which consists of several sub ontologies corresponding to substance, process, environment, and property, is developed using the ontology language of the Semantic Web, OWL, which enables the definition of a flexible and detailed structure of materials information. A versatile "materials data format" is built on the Materials Ontology as a component of the materials information platform and is applied to exchange data among three different thermal property databases, maintained by two major materials science research institutes in Japan.

  17. Thermodynamics of heat-and material-exchange in engineering

    Energy Technology Data Exchange (ETDEWEB)

    Matz, W.

    1944-05-23

    This book-length discussion of thermodynamics emphasized the situation of exchanges of heat and materials during various processes. Within the first chapter (on general foundations) the major headings were Points of view and means of representation, Conditions and characteristics of materials, The first law and energy, The second law and entropy, Equilibrium, and The general similarity-principle in heat-and material-exchange. The second chapter (on heat-and material-exchange in counterflow between two phases) had headings The harmonic triangle diagram, The heat exchanger, Heat exchange by means of procedures of blowing, Heating and cooling processes in vessels, Material exchange in couterflow, and Similarity among friction, heat-and material-exchange. The chapter on exchanges between vapor and liquid in single substances discussed evaporation processes and vapor-air mixtures. There were also chapters on exchanges during distillation, adsorption, absorption, and extraction. There was also an extensive bibliography and a collection of 107 diagrams of various types of representatives of thermodynamic relationships. (Some parts of the book appear out of order on the microfilm reels.) 107 diagrams.

  18. Anisotropic microporous supports impregnated with polymeric ion-exchange materials

    Science.gov (United States)

    Friesen, Dwayne; Babcock, Walter C.; Tuttle, Mark

    1985-05-07

    Novel ion-exchange media are disclosed, the media comprising polymeric anisotropic microporous supports containing polymeric ion-exchange or ion-complexing materials. The supports are anisotropic, having small exterior pores and larger interior pores, and are preferably in the form of beads, fibers and sheets.

  19. Advanced proton-exchange materials for energy efficient fuel cells.

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, Cy H.; Grest, Gary Stephen; Hickner, Michael A.; Cornelius, Christopher James; Staiger, Chad Lynn; Hibbs, Michael R.

    2005-12-01

    The ''Advanced Proton-Exchange Materials for Energy Efficient Fuel Cells'' Laboratory Directed Research and Development (LDRD) project began in October 2002 and ended in September 2005. This LDRD was funded by the Energy Efficiency and Renewable Energy strategic business unit. The purpose of this LDRD was to initiate the fundamental research necessary for the development of a novel proton-exchange membranes (PEM) to overcome the material and performance limitations of the ''state of the art'' Nafion that is used in both hydrogen and methanol fuel cells. An atomistic modeling effort was added to this LDRD in order to establish a frame work between predicted morphology and observed PEM morphology in order to relate it to fuel cell performance. Significant progress was made in the area of PEM material design, development, and demonstration during this LDRD. A fundamental understanding involving the role of the structure of the PEM material as a function of sulfonic acid content, polymer topology, chemical composition, molecular weight, and electrode electrolyte ink development was demonstrated during this LDRD. PEM materials based upon random and block polyimides, polybenzimidazoles, and polyphenylenes were created and evaluated for improvements in proton conductivity, reduced swelling, reduced O{sub 2} and H{sub 2} permeability, and increased thermal stability. Results from this work reveal that the family of polyphenylenes potentially solves several technical challenges associated with obtaining a high temperature PEM membrane. Fuel cell relevant properties such as high proton conductivity (>120 mS/cm), good thermal stability, and mechanical robustness were demonstrated during this LDRD. This report summarizes the technical accomplishments and results of this LDRD.

  20. Materials Ontology: An Infrastructure for Exchanging Materials Information and Knowledge

    National Research Council Canada - National Science Library

    Ashino, Toshihiro

    2010-01-01

    .... However, these resources have a wide variety of formats, terminologies, and concepts, which makes it difficult to find appropriate information for materials design, development, and evaluation...

  1. Research on Heterogeneous Data Exchange based on XML

    Science.gov (United States)

    Li, Huanqin; Liu, Jinfeng

    Integration of multiple data sources is becoming increasingly important for enterprises that cooperate closely with their partners for e-commerce. OLAP enables analysts and decision makers fast access to various materialized views from data warehouses. However, many corporations have internal business applications deployed on different platforms. This paper introduces a model for heterogeneous data exchange based on XML. The system can exchange and share the data among the different sources. The method used to realize the heterogeneous data exchange is given in this paper.

  2. Materials Ontology: An Infrastructure for Exchanging Materials Information and Knowledge

    OpenAIRE

    Toshihiro Ashino

    2010-01-01

    We have rich information resources for materials science and engineering - raw measurement data, computational simulation methods, digitized handbooks, and digital libraries. However, these resources have a wide variety of formats, terminologies, and concepts, which makes it difficult to find appropriate information for materials design, development, and evaluation. One solution to this problem is to integrate these resources into a computer readable concept map, called a domain ontology, whi...

  3. Strength of the rare-earth-transition-metal exchange coupling in hard magnetic materials, an experimental approach based on high-field magnetisation measurements: Application to Er sub 2 Fe sub 14 B

    Energy Technology Data Exchange (ETDEWEB)

    Verhoef, R.; Radwanski, R.J.; Franse, J.J.M. (Natuurkundig Lab., Univ. van Amsterdam (Netherlands))

    1990-09-01

    A new experimental technique is presented to determine the intersublattice molecular-field coefficient, n{sub RT}, in heavy rare-earth-transition-metal intermetallic compounds. The technique is based on high-field magnetisation measurements on finely powdered polycrystalline material that is free to rotate in the sampleholder. Experimental results are reported for a number of Er{sub 2}Fe{sub 14-x}Mn{sub x}B compounds. The strength of the R-T exchange coupling is not affected by the Mn substitution, and a value of 0.445 Tkg/Am{sup 2} has been deduced for the coefficient n{sub RT}. (orig.).

  4. Materials, Turbomachinery and Heat Exchangers for Supercritical CO2 Systems

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Mark; Nellis, Greg; Corradini, Michael

    2012-10-19

    The objective of this project is to produce the necessary data to evaluate the performance of the supercritical carbon dioxide cycle. The activities include a study of materials compatibility of various alloys at high temperatures, the heat transfer and pressure drop in compact heat exchanger units, and turbomachinery issues, primarily leakage rates through dynamic seals. This experimental work will serve as a test bed for model development and design calculations, and will help define further tests necessary to develop high-efficiency power conversion cycles for use on a variety of reactor designs, including the sodium fast reactor (SFR) and very high-temperature gas reactor (VHTR). The research will be broken into three separate tasks. The first task deals with the analysis of materials related to the high-temperature S-CO{sub 2} Brayton cycle. The most taxing materials issues with regard to the cycle are associated with the high temperatures in the reactor side heat exchanger and in the high-temperature turbine. The system could experience pressures as high as 20MPa and temperatures as high as 650°C. The second task deals with optimization of the heat exchangers required by the S-CO{sub 2} cycle; the S-CO{sub 2} flow passages in these heat exchangers are required whether the cycle is coupled with a VHTR or an SFR. At least three heat exchangers will be required: the pre-cooler before compression, the recuperator, and the heat exchanger that interfaces with the reactor coolant. Each of these heat exchangers is unique and must be optimized separately. The most challenging heat exchanger is likely the pre-cooler, as there is only about a 40°C temperature change but it operates close to the CO{sub 2} critical point, therefore inducing substantial changes in properties. The proposed research will focus on this most challenging component. The third task examines seal leakage through various dynamic seal designs under the conditions expected in the S-CO{sub 2} cycle

  5. A Liquid-Liquid Thermoelectric Heat Exchanger as a Heat Pump for Testing Phase Change Material Heat Exchangers

    Science.gov (United States)

    Sheth, Rubik B.; Makinen, Janice; Le, Hung V.

    2016-01-01

    The primary objective of the Phase Change HX payload on the International Space Station (ISS) is to test and demonstrate the viability and performance of Phase Change Material Heat Exchangers (PCM HX). The system was required to pump a working fluid through a PCM HX to promote the phase change material to freeze and thaw as expected on Orion's Multipurpose Crew Vehicle. Due to limitations on ISS's Internal Thermal Control System, a heat pump was needed on the Phase Change HX payload to help with reducing the working fluid's temperature to below 0degC (32degF). This paper will review the design and development of a TEC based liquid-liquid heat exchanger as a way to vary to fluid temperature for the freeze and thaw phase of the PCM HX. Specifically, the paper will review the design of custom coldplates and sizing for the required heat removal of the HX.

  6. Benzimidazole Based Aerogel Materials

    Science.gov (United States)

    Rhine, Wendell E. (Inventor); Mihalcik, David (Inventor)

    2016-01-01

    The present invention provides aerogel materials based on imidazoles and polyimidazoles. The polyimidazole based aerogel materials can be thermally stable up to 500 C or more, and can be carbonized to produce a carbon aerogel having a char yield of 60% or more, specifically 70% or more. The present invention also provides methods of producing polyimidazole based aerogel materials by reacting at least one monomer in a suitable solvent to form a polybenzimidazole gel precursor solution, casting the polybenzimidazole gel precursor solution into a fiber reinforcement phase, allowing the at least one gel precursor in the precursor solution to transition into a gel material, and drying the gel materials to remove at least a portion of the solvent, to obtain an polybenzimidazole-based aerogel material.

  7. The Representation and Exchange of Material and Other Engineering Properties

    Directory of Open Access Journals (Sweden)

    Norman Swindells

    2009-09-01

    Full Text Available The representation of information and its exchange in a communication requires the use of a common information model to define the semantics and syntax of the representation and a common dictionary to define the meaning of the data items. These fundamental concepts are the basis of the new standard ISO 10303-235: 'Engineering properties for product design and verification' for the computer representation and exchange of material and any other engineering properties of a product and to provide an audit trail for the derivation of the property value. A related dictionary conforming to ISO 13584 can define testing methods and their properties and enable the information model to be used for any property of any product.

  8. LDEF materials data bases

    Science.gov (United States)

    Funk, Joan G.; Strickland, John W.; Davis, John M.

    1993-01-01

    The Long Duration Exposure Facility (LDEF) and the accompanying experiments were composed of and contained a wide variety of materials representing the largest collection of materials flown in low Earth orbit (LEO) and retrieved for ground based analysis to date. The results and implications of the mechanical, thermal, optical, and electrical data from these materials are the foundation on which future LEO space missions will be built. The LDEF Materials Special Investigation Group (MSIG) has been charged with establishing and developing data bases to document these materials and their performance to assure not only that the data are archived for future generations but also that the data are available to the spacecraft user community in an easily accessed, user-friendly form. This paper discusses the format and content of the three data bases developed or being developed to accomplish this task. The hardware and software requirements for each of these three data bases are discussed along with current availability of the data bases. This paper also serves as a user's guide to the MAPTIS LDEF Materials Data Base.

  9. Novel silica-based ion exchange resin

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    Eichrom`s highly successful Diphonixo resin resembles a conventional ion exchange resin in its use of sulfonic acid ligands on a styrene- divinylbenzene matrix. Diphonix resin exhibits rapid exchange kinetics that allow economical operation of ion exchange systems. Unlike conventional resins, Diphonix resin contains chelating ligands that are diphosphonic acid groups that recognize and remove the targeted metals and reject the more common elements such as sodium, calcium and magnesium. This latter property makes Diphonix ideal for many industrial scale applications, including those involving waste treatment. For treatment of low-level, transuranic (TRU) and high- level radioactive wastes, Diphonix`s polystyrene backbone hinders its application due to radiolytic stability of the carbon-hydrogen bonds and lack of compatibility with expected vitrification schemes. Polystyrene-based Diphonix is approximately 60% carbon- hydrogen. In response to an identified need within the Department of Energy for a resin with the positive attributes of Diphonix that also exhibits greater radiolytic stability and final waste form compatibility, Eichrom has successfully developed a new, silica-based resin version of Diphonix. Target application for this new resin is for use in environmental restoration and waste management situations involving the processing of low-level, transuranic and high-level radioactive wastes. The resin can also be used for processing liquid mixed waste (waste that contains low level radioactivity and hazardous constituents) including mixed wastes contaminated with organic compounds. Silica-based Diphonix is only 10% carbon-hydrogen, with the bulk of the matrix silica.

  10. Experimental Investigation of Ice Phase Change Material Heat Exchangers

    Science.gov (United States)

    Leimkuehler, Thomas O.; Stephan, Ryan A.

    2012-01-01

    Phase change materials (PCM) may be useful for spacecraft thermal control systems that involve cyclical heat loads or cyclical thermal environments. Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. This can result in a decreased turndown ratio for the radiator and a reduced system mass. The use of water as a PCM rather than the more traditional paraffin wax has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. A number of ice PCM heat exchangers were fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion were investigated. This paper presents an overview of the results of this investigation from the past three years.

  11. Conceptual study of in-tank cesium removal using an inorganic ion exchange material

    Energy Technology Data Exchange (ETDEWEB)

    Goheen, R.S.; Kurath, D.E.

    1996-04-01

    Presently, the Hanford Site contains approximately 230,000 m{sup 3} of mixed waste stored in 177 underground tanks. Approximately 55,000 m{sup 3} of this waste is sludge, 90,000 m{sup 3} is salt cake, and 80,000 m{sup 3} is supernate. Although the pretreatment and final disposal requirements for the waste have not been entirely defined, it is likely that some supernatant pretreatment will be required to remove {sup 137}Cs and possibly {sup 90}Sr and the transuranic components. The objective of this study was to estimate the number of HLW glass canisters resulting from the use of inorganic ion exchanger materials as in-tank pretreatment technology. The variables in the study were: number of contacts between waste and ion exchange material; ion exchange material; and decontamination requirement. This conceptual study investigates a generic in-tank Cs removal flowsheet using crystalline silico-titanates and IE-96 zeolites, and the impact of each ion exchanger on the number of glass canisters produced. In determining glass formulation, data based on current reference technology was used. Sample calculations from the worksheets and summaries of final calculated results are included at the end of this report.

  12. Determining the sign of exchange coupling in a chromia based perpendicular exchange bias heterostructure

    Science.gov (United States)

    Singh, Uday; Street, Mike; Echtenkamp, Will; Binek, Christian; Adenwalla, Shireen

    Exchange bias arises from the coupling at the AFM/FM interface and, has been observed and studied in a wide range of systems. A key property of exchange bias systems is the sign of the coupling between the ferromagnet spins and the interfacial antiferromagnet spins, which may be aligned either ferromagnetically (parallel) or antiferromagnetically (antiparallel). Antiferromagnetic exchange coupling is known to be the generic cause of positive exchange bias. Determining the sign of exchange coupling is straight forward in system where the coupling is weak and can be overcome by Zeeman energy on field -cooling. It is, however, a challenging task when the available magnetic field is low or the magnitude of the exchange coupling is high. Here, we present a technique to determine the sign of the exchange coupling using low fields. We measure the exchange bias field as a function of ferromagnet magnetization during field cooling and the resultant behavior of the exchange bias vs. the magnetization uniquely determines the sign of the coupling. We use this to measure the sign of the exchange coupling in a Cr2O3(300 nm)/Pd(0.5 nm)/[Co(0.3 nm)/Pd(1 nm)]3 heterostructure thin film system and verify our results with the conventional high field method. This work was supported by the National Science Foundation (NSF) through Grant No. DMR-1409622 and the Nebraska Materials Research Science and Engineering Center (MRSEC) (Grant No. DMR-1420645).

  13. Isotope exchange reactions on ceramic breeder materials and their effect on tritium inventory

    Energy Technology Data Exchange (ETDEWEB)

    Nishikawa, M.; Baba, A. [Kyushu Univ., Fukuoka (Japan). Faculty of Engineering; Kawamura, Y.; Nishi, M.

    1998-03-01

    Though lithium ceramic materials such as Li{sub 2}O, LiAlO{sub 2}, Li{sub 2}ZrO{sub 3}, Li{sub 2}TiO{sub 3} and Li{sub 4}SiO{sub 4} are considered as breeding materials in the blanket of a D-T fusion reactor, the release behavior of the bred tritium in these solid breeder materials has not been fully understood. The isotope exchange reaction rate between hydrogen isotopes in the purge gas and tritium on the surface of breeding materials have not been quantified yet, although helium gas with hydrogen or deuterium is planned to be used as the blanket purge gas in the recent blanket designs. The mass transfer coefficient representing the isotope exchange reaction between H{sub 2} and D{sub 2}O or that between D{sub 2} and H{sub 2}O in the ceramic breeding materials bed is experimentally obtained in this study. Effects of isotope exchange reactions on the tritium inventory in the bleeding blanket is discussed based on data obtained in this study where effects of diffusion of tritium in the grain, absorption of water in the bulk of grain, and adsorption of water on the surface of grain, together with two types of isotope exchange reactions are considered. The way to estimate the tritium inventory in a Li{sub 2}ZrO{sub 3} blanket used in this study shows a good agreement with data obtained in such in-situ experiments as MOZART, EXOTIC-5, 6 and TRINE experiments. (author)

  14. Melting of Nanoprticle-Enhanced Phase Change Material inside Shell and Tube Heat Exchanger

    Directory of Open Access Journals (Sweden)

    Seiyed Mohammad Javad Hosseini

    2013-01-01

    Full Text Available This paper presents a numerical study of melting of Nanoprticle-Enhanced phase change material (NEPCM inside a shell and tube heat exchanger using RT50 and copper particles as base material and nanoparticle, respectively. In this study, the effects of nanoparticles dispersion (, 0.03, and 0.05 on melting time, liquid fraction, and penetration length are investigated. The results show that the melting time decreases to 14.6% and the penetration length increases to 146% with increasing volume fraction of nanoparticle up to .

  15. A Range-Based Multivariate Model for Exchange Rate Volatility

    NARCIS (Netherlands)

    B. Tims (Ben); R.J. Mahieu (Ronald)

    2003-01-01

    textabstractIn this paper we present a parsimonious multivariate model for exchange rate volatilities based on logarithmic high-low ranges of daily exchange rates. The multivariate stochastic volatility model divides the log range of each exchange rate into two independent latent factors, which are

  16. Phase Change Material (PCM) Heat Exchanger Development Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Project has identified two PCM HX concepts that will be designed, developed and demonstrated on-board the International Space Station (ISS):The first heat exchanger...

  17. Material Exchange Property of Organo Lead Halide Perovskite with Hole-Transporting Materials

    Directory of Open Access Journals (Sweden)

    Seigo Ito

    2015-10-01

    Full Text Available Using X-ray diffraction (XRD, it was confirmed that the deposition of hole-transporting materials (HTM on a CH3NH3PbI3 perovskite layer changed the CH3NH3PbI3 perovskite crystal, which was due to the material exchanging phenomena between the CH3NH3PbI3 perovskite and HTM layers. The solvent for HTM also changed the perovskite crystal. In order to suppress the crystal change, doping by chloride ion, bromide ion and 5-aminovaleric acid was attempted. However, the doping was unable to stabilize the perovskite crystal against HTM deposition. It can be concluded that the CH3NH3PbI3 perovskite crystal is too soft and flexible to stabilize against HTM deposition.

  18. Observer-based monitoring of heat exchangers.

    Science.gov (United States)

    Astorga-Zaragoza, Carlos-Manuel; Alvarado-Martínez, Víctor-Manuel; Zavala-Río, Arturo; Méndez-Ocaña, Rafael-Maxim; Guerrero-Ramírez, Gerardo-Vicente

    2008-01-01

    The goal of this work is to provide a method for monitoring performance degradation in counter-flow double-pipe heat exchangers. The overall heat transfer coefficient is estimated by an adaptive observer and monitored in order to infer when the heat exchanger needs preventive or corrective maintenance. A simplified mathematical model is used to synthesize the adaptive observer and a more complex model is used for simulation. The reliability of the proposed method was demonstrated via numerical simulations and laboratory experiments with a bench-scale pilot plant.

  19. Materials engineering data base

    Science.gov (United States)

    1995-01-01

    The various types of materials related data that exist at the NASA Marshall Space Flight Center and compiled into databases which could be accessed by all the NASA centers and by other contractors, are presented.

  20. Hydrogen adsorption over Zeolite-like MOF materials modified by ion exchange

    Energy Technology Data Exchange (ETDEWEB)

    Calleja, G.; Botas, J.A.; Orcajo, M.G. [Department of Chemical and Energy Technology, ESCET, Universidad Rey Juan Carlos, C/Tulipan s/n, 28933 Mostoles, Madrid (Spain); Sanchez-Sanchez, M. [Instituto de Catalisis y Petroleoquimica, CSIC, C/Marie Curie 2, 28049 Madrid (Spain)

    2010-09-15

    Novel porous Zeolite-like metal-organic framework (ZMOF) materials with Rho and Sod topologies are promising adsorbents for hydrogen storage due to their high surface area and, more importantly, to their capacity of being ion-exchanged, potentially changing their affinity for hydrogen. In this work, we have successfully synthesized both Rho and SodZMOF materials, optimizing experimental conditions for scaling-up the procedure already published to produce grams of material. The resultant materials were alkaline-cation-exchanged, widely characterized and finally tested as hydrogen adsorbents. RhoZMOF is converted into an amorphous phase during some of the ion-exchange processes, whereas SodZMOF, whose ion-exchange capacity has not been investigated so far, always maintains its topology for any tested exchange cation and conditions. Additionally, thermogravimetric analyses and thermal treatments followed by in-situ powder X-ray diffraction analysis have evidenced a significantly higher thermal stability of both as-prepared and ion-exchanged SodZMOF materials in comparison to their Rho-structured homologues. Moreover, the thermal stability of the cation-exchanged ZMOF samples improves when methanol is the ion-exchange solvent rather than the reported ethanol-water mixture. Nitrogen and hydrogen adsorption isotherms at 77 K suggested that alkali-exchanged materials have lower affinity for hydrogen than the as-prepared samples compensated by imidazolium ion; however, due to the smaller size of Na{sup +} or Li{sup +} cations, their lower affinity is easily compensated by the inherent increase in surface area and pore volume as exchange degree increases. (author)

  1. ION EXCHANGE PROCESS FOR THE RECOVERY AND PURIFICATION OF MATERIALS

    Science.gov (United States)

    Long, R.S.; Bailes, R.H.

    1958-04-15

    A process for the recovery of certain metallic ions from aqueous solutions by ion exchange techniques is described. It is applicable to elements such as vanadium, chromium, nnanganese, and the like, which are capable of forming lower valent cations soluble in aqueous solutions and which also form ldgher valent anions soluble in aqueous acidic solutions. For example, small amounts of vanadium occurring in phosphoric acid prepared from phosphate rock may be recovered by reducing the vanadium to a trivalent cation adsorbing; the vanadium in a cationic exchange resin, then treating the resin with a suitable oxidizing agent to convert the adsorbed vanadium to a higher valent state, and finally eluting; the vanadium as an anion from the resin by means of an aqueous acidic solution.

  2. New Copper-based Heat Exchangers for Alternative Refrigerants

    OpenAIRE

    Shabtay, Yoram; Black, John; Kraft, Frank

    2014-01-01

    The ongoing global effort to replace current refrigerants with zero Ozone Depletion Potential (ODP) and virtually zero Global Warming Potential (GWP) refrigerants has important implications for heat exchangers, air conditioning system design, and the materials choices in these designs. Natural refrigerants with higher flammability, CO2, new HFC blends, and new HFO’s each place different requirements on the heat exchanger design, whether it be for higher equipment efficiency, to reduce refrige...

  3. Assessment of commercially available ion exchange materials for cesium removal from highly alkaline wastes

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, K.P.; Kim, A.Y.; Kurath, D.E.

    1996-04-01

    Approximately 61 million gallons of nuclear waste generated in plutonium production, radionuclide removal campaigns, and research and development activities is stored on the Department of Energy`s Hanford Site, near Richland, Washington. Although the pretreatment process and disposal requirements are still being defined, most pretreatment scenarios include removal of cesium from the aqueous streams. In many cases, after cesium is removed, the dissolved salt cakes and supernates can be disposed of as LLW. Ion exchange has been a leading candidate for this separation. Ion exchange systems have the advantage of simplicity of equipment and operation and provide many theoretical stages in a small space. The organic ion exchange material Duolite{trademark} CS-100 has been selected as the baseline exchanger for conceptual design of the Initial Pretreatment Module (IPM). Use of CS-100 was chosen because it is considered a conservative, technologically feasible approach. During FY 96, final resin down-selection will occur for IPM Title 1 design. Alternate ion exchange materials for cesium exchange will be considered at that time. The purpose of this report is to conduct a search for commercially available ion exchange materials which could potentially replace CS-100. This report will provide where possible a comparison of these resin in their ability to remove low concentrations of cesium from highly alkaline solutions. Materials which show promise can be studied further, while less encouraging resins can be eliminated from consideration.

  4. Graphene-based smart materials

    Science.gov (United States)

    Yu, Xiaowen; Cheng, Huhu; Zhang, Miao; Zhao, Yang; Qu, Liangti; Shi, Gaoquan

    2017-09-01

    The high specific surface area and the excellent mechanical, electrical, optical and thermal properties of graphene make it an attractive component for high-performance stimuli-responsive or 'smart' materials. Complementary to these inherent properties, functionalization or hybridization can substantially improve the performance of these materials. Typical graphene-based smart materials include mechanically exfoliated perfect graphene, chemical vapour deposited high-quality graphene, chemically modified graphene (for example, graphene oxide and reduced graphene oxide) and their macroscopic assemblies or composites. These materials are sensitive to a range of stimuli, including gas molecules or biomolecules, pH value, mechanical strain, electrical field, and thermal or optical excitation. In this Review, we outline different graphene-based smart materials and their potential applications in actuators, chemical or strain sensors, self-healing materials, photothermal therapy and controlled drug delivery. We also introduce the working mechanisms of graphene-based smart materials and discuss the challenges facing the realization of their practical applications.

  5. Large-Scale Data Bases, Standards, and Exchange Procedures

    Science.gov (United States)

    Weathersby, George B.

    1976-01-01

    The increasing data about institutions of higher education and the availability of this data are described and evaluated. The data bases need further development and coordination of standards, exchange guidelines, and accessing procedures to be most beneficial. (Author/LBH)

  6. Next Generation Nuclear Plant Intermediate Heat Exchanger Materials Research and Development Plan (PLN-2804)

    Energy Technology Data Exchange (ETDEWEB)

    J. K. Wright

    2008-04-01

    DOE has selected the High Temperature Gas-cooled Reactor (HTGR) design for the Next Generation Nuclear Plant (NGNP) Project. The NGNP will demonstrate the use of nuclear power for electricity and hydrogen production. It will have an outlet gas temperature in the range of 900°C and a plant design service life of 60 years. The reactor design will be a graphite moderated, helium-cooled, prismatic or pebble-bed reactor and use low-enriched uranium, Tri-Isotopic (TRISO)-coated fuel. The plant size, reactor thermal power, and core configuration will ensure passive decay heat removal without fuel damage or radioactive material releases during accidents. The NGNP Materials Research and Development (R&D) Program is responsible for performing R&D on likely NGNP materials in support of the NGNP design, licensing, and construction activities. Today’s high-temperature alloys and associated ASME Codes for reactor applications are approved up to 760°C. However, some primary system components, such as the Intermediate Heat Exchanger (IHX) for the NGNP will require use of materials that can withstand higher temperatures. The thermal, environmental, and service life conditions of the NGNP will make selection and qualification of some high-temperature materials a significant challenge. Examples include materials for the core barrel and core internals, such as the control rod sleeves. The requirements of the materials for the IHX are among the most demanding. Selection of the technology and design configuration for the NGNP must consider both the cost and risk profiles to ensure that the demonstration plant establishes a sound foundation for future commercial deployments. The NGNP challenge is to achieve a significant advancement in nuclear technology while at the same time setting the stage for an economically viable deployment of the new technology in the commercial sector soon after 2020. A number of solid solution strengthened nickel based alloys have been considered for

  7. Next Generation Nuclear Plant Steam Generator and Intermediate Heat Exchanger Materials Research and Development Plan

    Energy Technology Data Exchange (ETDEWEB)

    J. K. Wright

    2010-09-01

    DOE has selected the High Temperature Gas-cooled Reactor (HTGR) design for the Next Generation Nuclear Plant (NGNP) Project. The NGNP will demonstrate the use of nuclear power for electricity and hydrogen production. It will have an outlet gas temperature in the range of 900°C and a plant design service life of 60 years. The reactor design will be a graphite moderated, helium-cooled, prismatic or pebble-bed reactor and use low-enriched uranium, Tri-Isotopic (TRISO)-coated fuel. The plant size, reactor thermal power, and core configuration will ensure passive decay heat removal without fuel damage or radioactive material releases during accidents. The NGNP Materials Research and Development (R&D) Program is responsible for performing R&D on likely NGNP materials in support of the NGNP design, licensing, and construction activities. Today’s high-temperature alloys and associated ASME Codes for reactor applications are approved up to 760°C. However, some primary system components, such as the Intermediate Heat Exchanger (IHX) for the NGNP will require use of materials that can withstand higher temperatures. The thermal, environmental, and service life conditions of the NGNP will make selection and qualification of some high-temperature materials a significant challenge. Examples include materials for the core barrel and core internals, such as the control rod sleeves. The requirements of the materials for the IHX are among the most demanding. Selection of the technology and design configuration for the NGNP must consider both the cost and risk profiles to ensure that the demonstration plant establishes a sound foundation for future commercial deployments. The NGNP challenge is to achieve a significant advancement in nuclear technology while at the same time setting the stage for an economically viable deployment of the new technology in the commercial sector soon after 2020. A number of solid solution strengthened nickel based alloys have been considered for

  8. Polyphosphazine-based polymer materials

    Science.gov (United States)

    Fox, Robert V.; Avci, Recep; Groenewold, Gary S.

    2010-05-25

    Methods of removing contaminant matter from porous materials include applying a polymer material to a contaminated surface, irradiating the contaminated surface to cause redistribution of contaminant matter, and removing at least a portion of the polymer material from the surface. Systems for decontaminating a contaminated structure comprising porous material include a radiation device configured to emit electromagnetic radiation toward a surface of a structure, and at least one spray device configured to apply a capture material onto the surface of the structure. Polymer materials that can be used in such methods and systems include polyphosphazine-based polymer materials having polyphosphazine backbone segments and side chain groups that include selected functional groups. The selected functional groups may include iminos, oximes, carboxylates, sulfonates, .beta.-diketones, phosphine sulfides, phosphates, phosphites, phosphonates, phosphinates, phosphine oxides, monothio phosphinic acids, and dithio phosphinic acids.

  9. Password-based authenticated key exchange scheme using smart card

    Science.gov (United States)

    Liu, Hui; Zhong, Shaojun

    2013-03-01

    A protocol that allows any two entities to negotiate a shared session key is commonly called a key exchange protocol. If the protocol provides a function to authenticate each other, we call the protocol authenticated key exchange protocol (AKE). Password authentication key exchange (PAKE) is the AKE protocol in which the two entities share a humanmemorable password. Most of current PAKE relies on the existence of a public key infrastructure, which sometime is impossible for a certain environments such as low computational device due to the computation overhead. In this paper, we propose password-based authenticated key exchange using smart card. Compared to previous PAKE, our protocol is more efficient because our protocol is based on ECC. Thereby, the proposed protocol can be well applied to low computation device.

  10. Preparation and characterization of 5-sulphosalicylic acid doped tetraethoxysilane composite ion-exchange material by sol–gel method

    Energy Technology Data Exchange (ETDEWEB)

    Rehman, Suhail-ul; Islam, Nasarul; Ahad, Sozia; Fatima, Syed Zeeshan; Pandith, Altaf Hussain, E-mail: altafpandit23@gmail.com

    2013-09-15

    Highlights: • Sulphosalicylic acid doped tetraethoxysilane composite is prepared by sol–gel method. •Its X-ray diffraction studies suggest that it is crystalline in nature. • This material shows selectivity for Mg(II) and Ni(II) ions in aqueous solutions. • Separation of Ni(II) from binary mixtures was successfully achieved on this material. -- Abstract: In this manuscript, we report the preparation and characterization of sulphosalicylic doped tetraethoxysilane (SATEOS), composite material by sol–gel method as a new ion exchanger for the removal of Ni(II) from aqueous solution. The fine granular material was prepared by acid catalyzed condensation polymerization through sol–gel mechanism in the presence of cationic surfactant. The material has an ion exchange capacity of 0.64 mequiv./g(dry) for sodium ions, 0.60 mequiv./g(dry) for potassium ions, 1.84 mequiv./g(dry) for magnesium ions, 1.08 mequiv./g(dry) for calcium ions and 1.36 mequiv./g(dry) for strontium ions. Its X-ray diffraction studies suggest that it is crystalline in nature. The material has been characterized by SEM, IR, TGA and DTG so as to identify the various functional groups and ion exchange sites present in this material. Quantum chemical computations at DFT/B3LYP/6-311G (d,p) level on model systems were performed to substantiate the structural conclusions based ion instrumental techniques. Investigations into the elution behaviour, ion exchange reversibility and distribution capacities of this material towards certain environmentally hazardous metal ions are also performed. The material shows good chemical stability towards acidic conditions and exhibits fast elution of exchangeable H{sup +} ions under neutral conditions. This material shows remarkable selectivity for Ni(II) and on the basis of its K{sub d} value (4 × 10{sup 2} in 0.01 M HClO{sub 4}) some binary separations of Ni(II) from other metal ions are performed.

  11. Lignin-Based Thermoplastic Materials.

    Science.gov (United States)

    Wang, Chao; Kelley, Stephen S; Venditti, Richard A

    2016-04-21

    Lignin-based thermoplastic materials have attracted increasing interest as sustainable, cost-effective, and biodegradable alternatives for petroleum-based thermoplastics. As an amorphous thermoplastic material, lignin has a relatively high glass-transition temperature and also undergoes radical-induced self-condensation at high temperatures, which limits its thermal processability. Additionally, lignin-based materials are usually brittle and exhibit poor mechanical properties. To improve the thermoplasticity and mechanical properties of technical lignin, polymers or plasticizers are usually integrated with lignin by blending or chemical modification. This Review attempts to cover the reported approaches towards the development of lignin-based thermoplastic materials on the basis of published information. Approaches reviewed include plasticization, blending with miscible polymers, and chemical modifications by esterification, etherification, polymer grafting, and copolymerization. Those lignin-based thermoplastic materials are expected to show applications as engineering plastics, polymeric foams, thermoplastic elastomers, and carbon-fiber precursors. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Liquid Salt Heat Exchanger Technology for VHTR Based Applications

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Mark; Sridhara, Kumar; Allen, Todd; Peterson, Per

    2012-10-11

    The objective of this research is to evaluate performance of liquid salt fluids for use as a heat carrier for transferring high-temperature process heat from the very high-temperature reactor (VHTR) to chemical process plants. Currently, helium is being considered as the heat transfer fluid; however, the tube size requirements and the power associated with pumping helium may not be economical. Recent work on liquid salts has shown tremendous potential to transport high-temperature heat efficiently at low pressures over long distances. This project has two broad objectives: To investigate the compatibility of Incoloy 617 and coated and uncoated SiC ceramic composite with MgCl2-KCl molten salt to determine component lifetimes and aid in the design of heat exchangers and piping; and, To conduct the necessary research on the development of metallic and ceramic heat exchangers, which are needed for both the helium-to-salt side and salt-to-process side, with the goal of making these heat exchangers technologically viable. The research will consist of three separate tasks. The first task deals with material compatibility issues with liquid salt and the development of techniques for on-line measurement of corrosion products, which can be used to measure material loss in heat exchangers. Researchers will examine static corrosion of candidate materials in specific high-temperature heat transfer salt systems and develop an in situ electrochemical probe to measure metallic species concentrations dissolved in the liquid salt. The second task deals with the design of both the intermediate and process side heat exchanger systems. Researchers will optimize heat exchanger design and study issues related to corrosion, fabrication, and thermal stresses using commercial and in-house codes. The third task focuses integral testing of flowing liquid salts in a heat transfer/materials loop to determine potential issues of using the salts and to capture realistic behavior of the salts in a

  13. Synthesis and characterization of a novel hybrid material as amphoteric ion exchanger for simultaneous removal of cations and anions.

    Science.gov (United States)

    Shah, Brijesh; Chudasama, Uma

    2014-07-15

    A new hybrid chelating ion exchanger zirconium diethylene triamine (ZrD) has been synthesized by a simple sol-gel route using inexpensive and easily available chemicals. ZrD has been characterized for elemental analysis (ICP-AES, CHN analysis), TGA, FTIR, X-ray diffraction, SEM and EDX. Physical and ion exchange characteristics as well as chemical stability of the material in various media have been studied. Structural determination reveals that ZrD exhibits amphoteric character. Anion exchange capacity (AEC) for Cl(-), Br(-), Cr2O7(2-), F(-) and AsO4(3-) has been determined. Cations are exchanged through chelation where coordinating sites are offered by nitrogen atoms present in the amine groups of ZrD. Distribution coefficient Kd for Co(2+), Ni(2+), Cu(2+), Zn(2+) (transition metal ions) and Hg(2+), Cd(2+), Pb(2+) (heavy metal ions) has been evaluated by batch equilibration techniques in aqueous and various electrolyte media/concentrations. Based on α the separation factor, a few binary separations have been performed on a chromatographic column packed with ZrD. The amphoteric behaviour of ZrD has been demonstrated by simultaneous exchange of Cu(2+) and Cl(-) in CuCl2. A study on the regeneration and reuse of ZrD indicates that it is effective upto four cycles without much decline in performance. Copyright © 2014 Elsevier B.V. All rights reserved.

  14. Custom-tailored adsorbers: A molecular dynamics study on optimal design of ion exchange chromatography material.

    Science.gov (United States)

    Lang, Katharina M H; Kittelmann, Jörg; Pilgram, Florian; Osberghaus, Anna; Hubbuch, Jürgen

    2015-09-25

    The performance of functionalized materials, e.g., ion exchange resins, depends on multiple resin characteristics, such as type of ligand, ligand density, the pore accessibility for a molecule, and backbone characteristics. Therefore, the screening and identification process for optimal resin characteristics for separation is very time and material consuming. Previous studies on the influence of resin characteristics have focused on an experimental approach and to a lesser extent on the mechanistic understanding of the adsorption mechanism. In this in silico study, a previously developed molecular dynamics (MD) tool is used, which simulates any given biomolecule on resins with varying ligand densities. We describe a set of simulations and experiments with four proteins and six resins varying in ligand density, and show that simulations and experiments correlate well in a wide range of ligand density. With this new approach simulations can be used as pre-experimental screening for optimal adsorber characteristics, reducing the actual number of screening experiments, which results in a faster and more knowledge-based development of custom-tailored adsorbers. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Development of a Malian food exchange system based on local ...

    African Journals Online (AJOL)

    Energy and macronutrient intakes obtained by a software-based nutritional analysis of the dietary recalls were compared with the average energy and nutrient values calculated with the exchange lists. Setting: Centre National de Lutte contre le Diabète. Subjects: Seventeen male and 40 female adults with type 2 diabetes.

  16. Implementation of Medical Information Exchange System Based on EHR Standard.

    Science.gov (United States)

    Han, Soon Hwa; Lee, Min Ho; Kim, Sang Guk; Jeong, Jun Yong; Lee, Bi Na; Choi, Myeong Seon; Kim, Il Kon; Park, Woo Sung; Ha, Kyooseob; Cho, Eunyoung; Kim, Yoon; Bae, Jae Bong

    2010-12-01

    To develop effective ways of sharing patients' medical information, we developed a new medical information exchange system (MIES) based on a registry server, which enabled us to exchange different types of data generated by various systems. To assure that patient's medical information can be effectively exchanged under different system environments, we adopted the standardized data transfer methods and terminologies suggested by the Center for Interoperable Electronic Healthcare Record (CIEHR) of Korea in order to guarantee interoperability. Regarding information security, MIES followed the security guidelines suggested by the CIEHR of Korea. This study aimed to develop essential security systems for the implementation of online services, such as encryption of communication, server security, database security, protection against hacking, contents, and network security. The registry server managed information exchange as well as the registration information of the clinical document architecture (CDA) documents, and the CDA Transfer Server was used to locate and transmit the proper CDA document from the relevant repository. The CDA viewer showed the CDA documents via connection with the information systems of related hospitals. This research chooses transfer items and defines document standards that follow CDA standards, such that exchange of CDA documents between different systems became possible through ebXML. The proposed MIES was designed as an independent central registry server model in order to guarantee the essential security of patients' medical information.

  17. Influence of Ionic Liquids on the Selectivity of Ion Exchange-Based Polymer Membrane Sensing Layers.

    Science.gov (United States)

    Mendecki, Lukasz; Callan, Nicole; Ahern, Meghan; Schazmann, Benjamin; Radu, Aleksandar

    2016-07-16

    The applicability of ion exchange membranes is mainly defined by their permselectivity towards specific ions. For instance, the needed selectivity can be sought by modifying some of the components required for the preparation of such membranes. In this study, a new class of materials -trihexyl(tetradecyl)phosphonium based ionic liquids (ILs) were used to modify the properties of ion exchange membranes. We determined selectivity coefficients for iodide as model ion utilizing six phosphonium-based ILs and compared the selectivity with two classical plasticizers. The dielectric properties of membranes plasticized with ionic liquids and their response characteristics towards ten different anions were investigated using potentiometric and impedance measurements. In this large set of data, deviations of obtained selectivity coefficients from the well-established Hofmeister series were observed on many occasions thus indicating a multitude of applications for these ion-exchanging systems.

  18. Pulmonary gas exchange and acid-base balance during exercise.

    Science.gov (United States)

    Stickland, Michael K; Lindinger, Michael I; Olfert, I Mark; Heigenhauser, George J F; Hopkins, Susan R

    2013-04-01

    As the first step in the oxygen-transport chain, the lung has a critical task: optimizing the exchange of respiratory gases to maintain delivery of oxygen and the elimination of carbon dioxide. In healthy subjects, gas exchange, as evaluated by the alveolar-to-arterial PO2 difference (A-aDO2), worsens with incremental exercise, and typically reaches an A-aDO2 of approximately 25 mmHg at peak exercise. While there is great individual variability, A-aDO2 is generally largest at peak exercise in subjects with the highest peak oxygen consumption. Inert gas data has shown that the increase in A-aDO2 is explained by decreased ventilation-perfusion matching, and the development of a diffusion limitation for oxygen. Gas exchange data does not indicate the presence of right-to-left intrapulmonary shunt developing with exercise, despite recent data suggesting that large-diameter arteriovenous shunt vessels may be recruited with exercise. At the same time, multisystem mechanisms regulate systemic acid-base balance in integrative processes that involve gas exchange between tissues and the environment and simultaneous net changes in the concentrations of strong and weak ions within, and transfer between, extracellular and intracellular fluids. The physicochemical approach to acid-base balance is used to understand the contributions from independent acid-base variables to measured acid-base disturbances within contracting skeletal muscle, erythrocytes and noncontracting tissues. In muscle, the magnitude of the disturbance is proportional to the concentrations of dissociated weak acids, the rate at which acid equivalents (strong acid) accumulate and the rate at which strong base cations are added to or removed from muscle.

  19. Exchange Bias Effects in Iron Oxide-Based Nanoparticle Systems

    Science.gov (United States)

    Phan, Manh-Huong; Alonso, Javier; Khurshid, Hafsa; Lampen-Kelley, Paula; Chandra, Sayan; Stojak Repa, Kristen; Nemati, Zohreh; Das, Raja; Iglesias, Óscar; Srikanth, Hariharan

    2016-01-01

    The exploration of exchange bias (EB) on the nanoscale provides a novel approach to improving the anisotropic properties of magnetic nanoparticles for prospective applications in nanospintronics and nanomedicine. However, the physical origin of EB is not fully understood. Recent advances in chemical synthesis provide a unique opportunity to explore EB in a variety of iron oxide-based nanostructures ranging from core/shell to hollow and hybrid composite nanoparticles. Experimental and atomistic Monte Carlo studies have shed light on the roles of interface and surface spins in these nanosystems. This review paper aims to provide a thorough understanding of the EB and related phenomena in iron oxide-based nanoparticle systems, knowledge of which is essential to tune the anisotropic magnetic properties of exchange-coupled nanoparticle systems for potential applications. PMID:28335349

  20. Server-Controlled Identity-Based Authenticated Key Exchange

    Science.gov (United States)

    Guo, Hua; Mu, Yi; Zhang, Xiyong; Li, Zhoujun

    We present a threshold identity-based authenticated key exchange protocol that can be applied to an authenticated server-controlled gateway-user key exchange. The objective is to allow a user and a gateway to establish a shared session key with the permission of the back-end servers, while the back-end servers cannot obtain any information about the established session key. Our protocol has potential applications in strong access control of confidential resources. In particular, our protocol possesses the semantic security and demonstrates several highly-desirable security properties such as key privacy and transparency. We prove the security of the protocol based on the Bilinear Diffie-Hellman assumption in the random oracle model.

  1. Development of heat exchanger for high temperature energy storage with bulk materials

    Science.gov (United States)

    Boura, Cristiano Teixeira; Niederwestberg, Stefan; McLeod, Jacqueline; Herrmann, Ulf; Hoffschmidt, Bernhard

    2016-05-01

    This paper gives a general overview of the concept of a high temperature gas-to-particle heat exchanger, the corresponding test facilities and the results of laboratory tests. A description of the optimal bulk material and separator properties and their influences on the operating conditions is also given. The three phenomena pinning, blistering and blocking could be observed during the tests and were analysed in more detail using simulation software.

  2. Polypropylene based anion exchange fiber for enrichment and ...

    African Journals Online (AJOL)

    Indium was enriched and separated by a new polypropylene based anion exchange fiber before determined by graphite furnace atomic absorption spectrometry (GFAAS). Indium can be enriched quantitatively by 0.1 g of fiber at the flow rate within 6 mL·min-1 in the pH 4 and can be desorbed quantitatively with 10 mL of 1.0 ...

  3. Recent Development of Pd-Based Electrocatalysts for Proton Exchange Membrane Fuel Cells

    Directory of Open Access Journals (Sweden)

    Hui Meng

    2015-07-01

    Full Text Available This review selectively summarizes the latest developments in the Pd-based cataysts for low temperature proton exchange membrane fuel cells, especially in the application of formic acid oxidation, alcohol oxidation and oxygen reduction reaction. The advantages and shortcomings of the Pd-based catalysts for electrocatalysis are analyzed. The influence of the structure and morphology of the Pd materials on the performance of the Pd-based catalysts were described. Finally, the perspectives of future trends on Pd-based catalysts for different applications were considered.

  4. Synthesis of granular zeolitic materials with high cation exchange capacity from agglomerated coal fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Roberto Juan; Susana Hernandez; Jose Manuel Andres; Carmen Ruiz [Instituto de Carboquimica (CSIC), Zaragoza (Spain)

    2007-08-15

    Fly ash from coal combustion is a potential source of pollution and there is continuous interest in its recycling by converting it into products such as zeolitic materials for use in retaining pollutants. In this paper, production of granular zeolitic material from a commercially-unusable fine-fraction of a lightweight aggregate (LA) building material made from coal fly ash agglomerated with lime, by conventional alkaline activation is described. NaP1 zeolite, K-F zeolite, K-Phillipsite and K-Chabazite were synthesised. The process was optimised by combining four reaction parameters (temperature, alkali concentration, solution/fly ash ratio and reaction time). Zeolitic materials with the highest zeolite yields and cation exchange capacities were selected for future application in environmental processes. End-product zeolitic materials maintain its granular form and this could favour their use in some particular applications for environmental waste treatment (e.g. ionic exchange in column) without any further transformation stages. 21 refs., 6 figs., 6 tabs.

  5. High temperature corrosion of advanced ceramic materials for hot-gas filters and heat exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Kupp, E.R.; Trubelja, M.F.; Spear, K.E.; Tressler, R.E. [Pennsylvania State Univ., University Park, PA (United States)

    1995-08-01

    Experimental corrosion studies of hot gas filter materials and heat exchanger materials in oxidizing combustion environments have been initiated. Filter materials from 3M Co. and DuPont Lanxide Composites Inc. are being tested over a range of temperatures, times and gas flows. It has been demonstrated that morphological and phase changes due to corrosive effects occur after exposure of the 3M material to a combustion environment for as little as 25 hours at 800{degrees}C. The study of heat exchanger materials has focused on enhancing the corrosion resistance of DuPont Lanxide Dimox{trademark} composite tubes by adding chromium to its surfaces by (1) heat treatments in a Cr{sub 2}O{sub 3} powder bed, or (2) infiltrating surface porosity with molten chromium nitrate. Each process is followed by a surface homogenization at 1500{degrees}C. The powder bed method has been most successful, producing continuous Cr-rich layers with thicknesses ranging from 20 to 250 {mu}m. As-received and Cr-modified DuPont Lanxide Dimox{trademark} samples will be reacted with commonly encountered coal-ash slags to determine the Cr effects on corrosion resistance.

  6. Materials for Electroactive Ion-Exchange (EaIX) Separations of Pertechnetate Ion

    Energy Technology Data Exchange (ETDEWEB)

    Stender, Matthias; Hubler, Timothy L.; Alhoshan, Mansour; Smyrl, William H.

    2004-03-29

    Many contaminants of interest to the U.S. Department of Energy (DOE) exist as anions (e.g. chromate, pertechnetate and nitrate). The objective of this study is to develop Electroactive Ion-Exchange (EaIX) materials. Such materials can be used to separate pertechnetate ion from radioactive wastes located at DOE sites while limiting the amount of secondary wastes generated. We have developed a synthetic strategy to prepare vinyl-bipyridyl and -terpyridyl ligands which allow incorporation of ion-selective architectures with a polymerizable handle. Fe complexes formed with these ligands provide the working core of the electroactive polymers. The polymers can be directly used as materials for EaIX or they can be incorporated into porous composite materials that are then used for EaIX.

  7. THE EFFECT OF THE ELECTRON-OPAQUE PORE MATERIAL ON EXCHANGES THROUGH THE NUCLEAR ANNULI

    Science.gov (United States)

    Feldherr, Carl M.

    1965-01-01

    To investigate the extent to which the electron-opaque pore material can regulate nucleocytoplasmic exchanges which occur through the nuclear annuli, experiments were performed in which polyvinylpyrrolidone (PVP)-coated colloidal gold particles (25 to 170 A in diameter) were microinjected into the cytoplasm of amebas (Amoeba proteus). The cells were fixed at various times after injection and examined with the electron microscope in order to determine the location of the gold particles. High concentrations of gold were found associated with the pore material at specific points adjacent to and within the pores. It is tentatively suggested that such specific accumulations could be a means of selecting substances from the cytoplasm for transport through the pores. Particles were also scattered throughout the ground cytoplasm and nucleoplasm. A comparison of the diameters of particles located in these two regions showed that the ability of materials to penetrate the nuclear envelope is a function of their size. It was estimated that the maximum size of the particles able to enter the nucleus is approximately 125 to 145 A indiameter. The regulation of exchanges with regard to particle size is thought to be dependent on the specific organization of the electron-opaque pore material. PMID:14283630

  8. Risk Based Inspection of Gas-Cooling Heat Exchanger

    Directory of Open Access Journals (Sweden)

    Dwi Priyanta

    2017-09-01

    Full Text Available On October 2013, Pertamina Hulu Energi Offshore North West Java (PHE – ONWJ platform personnel found 93 leaking tubes locations in the finfan coolers/ gas-cooling heat exchanger. After analysis had been performed, the crack in the tube strongly indicate that stress corrosion cracking was occurred by chloride. Chloride stress corrosion cracking (CLSCC is the cracking occurred by the combined influence of tensile stress and a corrosive environment. CLSCC is the one of the most common reasons why austenitic stainless steel pipework or tube and vessels deteriorate in the chemical processing, petrochemical industries and maritime industries. In this thesis purpose to determine the appropriate inspection planning for two main items (tubes and header box in the gas-cooling heat exchanger using risk based inspection (RBI method. The result, inspection of the tubes must be performed on July 6, 2024 and for the header box inspection must be performed on July 6, 2025. In the end, RBI method can be applicated to gas-cooling heat exchanger. Because, risk on the tubes can be reduced from 4.537 m2/year to 0.453 m2/year. And inspection planning for header box can be reduced from 4.528 m2/year to 0.563 m2/year.

  9. State-of-the-art survey of joinability of materials for OTEC heat exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Beaver, R. J.

    1978-12-01

    Literature and industrial sources were surveyed to assess, on the basis of apparent economics and reliability, the joinability of both shell-and-tube and compact ocean thermal energy conversion (OTEC) heat exchangers. A no-leak requirement is mandatory to prevent mixing seawater and the ammonia working fluid. The operating temperature range considered is 7 to 28/sup 0/C (45 to 82/sup 0/F). Materials evaluated were aluminum, titanium, copper--nickel, AL-6X austenitic stainless steel, singly and in combination with steel and concrete. Many types of welding and brazing processes, roller expansion, magnaforming, O-ring sealing, and adhesive bonding were considered. The automatic gas tungsten-arc welding process and explosion welding processes are the only two joining processes that now appear to offer the high reliability required of no-leak shell-and-tube heat exchangers. Of these two processes, the gas tungsten-arc welding process appears to be the more economically attractive.

  10. Proton exchange membranes based on PVDF/SEBS blends

    Science.gov (United States)

    Mokrini, A.; Huneault, M. A.

    Proton-conductive polymer membranes are used as an electrolyte in the so-called proton exchange membrane fuel cells. Current commercially available membranes are perfluorosulfonic acid polymers, a class of high-cost ionomers. This paper examines the potential of polymer blends, namely those of styrene-(ethylene-butylene)-styrene block copolymer (SEBS) and polyvinylidene fluoride (PVDF), in the proton exchange membrane application. SEBS/PVDF blends were prepared by twin-screw extrusion and the membranes were formed by calendering. SEBS is a phase-segregated material where the polystyrene blocks can be selectively functionalized offering high ionic conductivity, while PVDF insures good dimensional stability and chemical resistance to the films. Proton conductivity of the films was obtained by solid-state grafting of sulfonic acid moieties. The obtained membranes were characterized in terms of conductivity, ionic exchange capacity and water uptake. In addition, the membranes were characterized in terms of morphology, microstructure and thermo-mechanical properties to establish the blends morphology-property relationships. Modification of interfacial properties between SEBS and PVDF was found to be a key to optimize the blends performance. Addition of a methyl methacrylate-butyl acrylate-methyl methacrylate block copolymer (MMA-BA-MMA) was found to compatibilize the blend by reducing the segregation scale and improving the blend homogeneity. Mechanical resistance of the membranes was also improved through the addition of this compatibilizer. As little as 2 wt.% compatibilizer was sufficient for complete interfacial coverage and lead to improved mechanical properties. Compatibilized blend membranes also showed higher conductivities, 1.9 × 10 -2 to 5.5 × 10 -3 S cm -1, and improved water management.

  11. A Review of Metallic Bipolar Plates for Proton Exchange Membrane Fuel Cells: Materials and Fabrication Methods

    Directory of Open Access Journals (Sweden)

    Shahram Karimi

    2012-01-01

    Full Text Available The proton exchange membrane fuel cell offers an exceptional potential for a clean, efficient, and reliable power source. The bipolar plate is a key component in this device, as it connects each cell electrically, supplies reactant gases to both anode and cathode, and removes reaction products from the cell. Bipolar plates have been fabricated primarily from high-density graphite, but in recent years, much attention has been paid to developing cost-effective and feasible alternative materials. Two different classes of materials have attracted attention: metals and composites. This paper offers a comprehensive review of the current research being carried out on metallic bipolar plates, covering materials and fabrication methods.

  12. Packaging based on polymeric materials

    Directory of Open Access Journals (Sweden)

    Jovanović Slobodan M.

    2005-01-01

    Full Text Available In the past two years the consumption of common in the developed countries world wide (high tonnage polymers for packaging has approached a value of 50 wt.%. In the same period more than 50% of the packaging units on the world market were made of polymeric materials despite the fact that polymeric materials present 17 wt.% of all packaging materials. The basic properties of polymeric materials and their environmental and economical advantages, providing them such a position among packaging materials, are presented in this article. Recycling methods, as well as the development trends of polymeric packaging materials are also presented.

  13. Quantifying the Pathway and Predicting Spontaneous Emulsification during Material Exchange in a Two Phase Liquid System.

    Science.gov (United States)

    Spooner, Stephen; Rahnama, Alireza; Warnett, Jason M; Williams, Mark A; Li, Zushu; Sridhar, Seetharaman

    2017-10-30

    Kinetic restriction of a thermodynamically favourable equilibrium is a common theme in materials processing. The interfacial instability in systems where rate of material exchange is far greater than the mass transfer through respective bulk phases is of specific interest when tracking the transient interfacial area, a parameter integral to short processing times for productivity streamlining in all manufacturing where interfacial reaction occurs. This is even more pertinent in high-temperature systems for energy and cost savings. Here the quantified physical pathway of interfacial area change due to material exchange in liquid metal-molten oxide systems is presented. In addition the predicted growth regime and emulsification behaviour in relation to interfacial tension as modelled using phase-field methodology is shown. The observed in-situ emulsification behaviour links quantitatively the geometry of perturbations as a validation method for the development of simulating the phenomena. Thus a method is presented to both predict and engineer the formation of micro emulsions to a desired specification.

  14. Templated synthesis, postsynthetic metal exchange, and properties of a porphyrin-encapsulating metal-organic material

    KAUST Repository

    Zhang, ZhenJie

    2012-01-18

    Reaction of biphenyl-3,4′,5-tricarboxylate (H 3BPT) and CdCl 2 in the presence of meso-tetra(N-methyl-4-pyridyl)porphine tetratosylate (TMPyP) afforded porph@MOM-10, a microporous metal-organic material containing CdTMPyP cations encapsulated in an anionic Cd(II) carboxylate framework, [Cd 6(BPT) 4Cl 4(H 2O) 4]. Porph@MOM-10 is a versatile platform that undergoes exchange to serve as the parent of a series of porph@MOMs that exhibit permanent porosity and heterogeneous catalytic activity. © 2011 American Chemical Society.

  15. Chiral quantum dot based materials

    Science.gov (United States)

    Govan, Joseph; Loudon, Alexander; Baranov, Alexander V.; Fedorov, Anatoly V.; Gun'ko, Yurii

    2014-05-01

    Recently, the use of stereospecific chiral stabilising molecules has also opened another avenue of interest in the area of quantum dot (QD) research. The main goal of our research is to develop new types of technologically important quantum dot materials containing chiral defects, study their properties and explore their applications. The utilisation of chiral penicillamine stabilisers allowed the preparation of new water soluble white emitting CdS quantum nanostructures which demonstrated circular dichroism in the band-edge region of the spectrum. It was also demonstrated that all three types of QDs (D-, L-, and Rac penicillamine stabilised) show very broad emission bands between 400 and 700 nm due to defects or trap states on the surfaces of the nanocrystals. In this work the chiral CdS based quantum nanostructures have also been doped by copper metal ions and new chiral penicilamine stabilized CuS nanoparticles have been prepared and investigated. It was found that copper doping had a strong effect at low levels in the synthesis of chiral CdS nanostructures. We expect that this research will open new horizons in the chemistry of chiral nanomaterials and their application in biotechnology, sensing and asymmetric synthesis.

  16. Proton Exchange Membrane fuel cell development with lightweight component materials, phase 1

    Science.gov (United States)

    Abens, Sandors

    1995-07-01

    Although the Proton Exchange Membrane (PEM) fuel cell is a leading candidate for an automobile power source through meeting the zero emission requirement, its power density is currently an order of magnitude below the 400 W/kg criterion proposed by the Department of Energy. The major contributors to stack weight are the bipolar gas distribution plates. This effort, performed jointly by Energy Research Corporation (ERC) and Texas A&M University (TAM U), focused on lightweight alternative bipolar plate materials and designs. The electronic conductivity of various candidate materials was evaluated. The emphasis was on conductive plastic materials and porous graphite. Several plastic materials with specific resistance between 0.5 and 0.8 ohm/cm were identified. Preliminary evaluation of lightweight materials was performed in single cell tests. The emphasis was on atmospheric pressure and internally humidified cell operation as a potential means of system simplification and reduction of PEM fuel cell ancillary equipment complexity and weight. The performance of single cells was nearly the same at 1 and 3 atm pressure. At a cell potential of O.6V, a current density of 230 mA/sq cm was reached at 1.7 stoichiometric air flow rate. With lightweight bipolar plates, the DOE power density target may be achieved with unpressurized, internally humidified cell stacks.

  17. Proton exchange membrane materials for the advancement of direct methanol fuel-cell technology

    Science.gov (United States)

    Cornelius, Christopher J [Albuquerque, NM

    2006-04-04

    A new class of hybrid organic-inorganic materials, and methods of synthesis, that can be used as a proton exchange membrane in a direct methanol fuel cell. In contrast with Nafion.RTM. PEM materials, which have random sulfonation, the new class of materials have ordered sulfonation achieved through self-assembly of alternating polyimide segments of different molecular weights comprising, for example, highly sulfonated hydrophilic PDA-DASA polyimide segment alternating with an unsulfonated hydrophobic 6FDA-DAS polyimide segment. An inorganic phase, e.g., 0.5 5 wt % TEOS, can be incorporated in the sulfonated polyimide copolymer to further improve its properties. The new materials exhibit reduced swelling when exposed to water, increased thermal stability, and decreased O.sub.2 and H.sub.2 gas permeability, while retaining proton conductivities similar to Nafion.RTM.. These improved properties may allow direct methanol fuel cells to operate at higher temperatures and with higher efficiencies due to reduced methanol crossover.

  18. Tag Content Access Control with Identity-based Key Exchange

    Science.gov (United States)

    Yan, Liang; Rong, Chunming

    2010-09-01

    Radio Frequency Identification (RFID) technology that used to identify objects and users has been applied to many applications such retail and supply chain recently. How to prevent tag content from unauthorized readout is a core problem of RFID privacy issues. Hash-lock access control protocol can make tag to release its content only to reader who knows the secret key shared between them. However, in order to get this shared secret key required by this protocol, reader needs to communicate with a back end database. In this paper, we propose to use identity-based secret key exchange approach to generate the secret key required for hash-lock access control protocol. With this approach, not only back end database connection is not needed anymore, but also tag cloning problem can be eliminated at the same time.

  19. Investigation of material efficient fin patterns for cost-effective operation of fin and tube heat exchanger

    DEFF Research Database (Denmark)

    Singh, Shobhana; Sørensen, Kim; Condra, Thomas Joseph

    2017-01-01

    Design management of a thermal energy system is a critical part of identifying basic designs that meet large scale user demand under certain operating characteristics. Fin and tube heat exchangers are among the most commonly used thermal energy systems which are generating considerable interest...... and tube heat exchanger. Computational fluid dynamic models of fin and tube heat exchanger with different fin patterns are developed to investigate the fin pattern behavior on heat transfer and pressure loss performance data. In addition, the numerical results are utilized to analyze the engineering design...... scale-up heat exchanger configurations with each fin pattern focusing on the application of chosen fin and tube heat exchanger in marine exhaust gas boiler. The analysis highlights the impact of material efficient fin patterns investigated and predicts that the polynomial and sinusoidal fin patterns...

  20. Towards efficient data exchange and sharing for big-data driven materials science: metadata and data formats

    Science.gov (United States)

    Ghiringhelli, Luca M.; Carbogno, Christian; Levchenko, Sergey; Mohamed, Fawzi; Huhs, Georg; Lüders, Martin; Oliveira, Micael; Scheffler, Matthias

    2017-11-01

    With big-data driven materials research, the new paradigm of materials science, sharing and wide accessibility of data are becoming crucial aspects. Obviously, a prerequisite for data exchange and big-data analytics is standardization, which means using consistent and unique conventions for, e.g., units, zero base lines, and file formats. There are two main strategies to achieve this goal. One accepts the heterogeneous nature of the community, which comprises scientists from physics, chemistry, bio-physics, and materials science, by complying with the diverse ecosystem of computer codes and thus develops "converters" for the input and output files of all important codes. These converters then translate the data of each code into a standardized, code-independent format. The other strategy is to provide standardized open libraries that code developers can adopt for shaping their inputs, outputs, and restart files, directly into the same code-independent format. In this perspective paper, we present both strategies and argue that they can and should be regarded as complementary, if not even synergetic. The represented appropriate format and conventions were agreed upon by two teams, the Electronic Structure Library (ESL) of the European Center for Atomic and Molecular Computations (CECAM) and the NOvel MAterials Discovery (NOMAD) Laboratory, a European Centre of Excellence (CoE). A key element of this work is the definition of hierarchical metadata describing state-of-the-art electronic-structure calculations.

  1. Highly Conductive Anion-Exchange Membranes from Microporous Tröger's Base Polymers.

    Science.gov (United States)

    Yang, Zhengjin; Guo, Rui; Malpass-Evans, Richard; Carta, Mariolino; McKeown, Neil B; Guiver, Michael D; Wu, Liang; Xu, Tongwen

    2016-09-12

    The development of polymeric anion-exchange membranes (AEMs) combining high ion conductivity and long-term stability is a major challenge for materials chemistry. AEMs with regularly distributed fixed cationic groups, based on the formation of microporous polymers containing the V-shape rigid Tröger's base units, are reported for the first time. Despite their simple preparation, which involves only two synthetic steps using commercially available precursors, the polymers provide AEMs with exceptional hydroxide conductivity at relatively low ion-exchange capacity, as well as a high swelling resistance and chemical stability. An unprecedented hydroxide conductivity of 164.4 mS cm(-1) is obtained at a relatively a low ion-exchange capacity of 0.82 mmol g(-1) under optimal operating conditions. The exceptional anion conductivity appears related to the intrinsic microporosity of the charged polymer matrix, which facilitates rapid anion transport. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Testing and Failure Mechanisms of Ice Phase Change Material Heat Exchangers

    Science.gov (United States)

    Leimkuehler, Thomas O.; Stephan, Ryan A.; Hawkins-Reynolds, Ebony

    2011-01-01

    Phase change materials (PCM) may be useful for thermal control systems that involve cyclical heat loads or cyclical thermal environments such as specific spacecraft orientations in Low Earth Orbit (LEO) and low beta angle Low Lunar Orbit (LLO). Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. One advantage that PCM s have over evaporators in this scenario is that they do not use a consumable. The use of water as a PCM rather than the more traditional paraffin wax has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. A number of ice PCM heat exchangers were fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion were investigated. This paper presents the results of testing that occurred from March through September of 2010 and builds on testing that occurred during the previous year.

  3. Development, Testing, and Failure Mechanisms of a Replicative Ice Phase Change Material Heat Exchanger

    Science.gov (United States)

    Leimkuehler, Thomas O.; Hansen, Scott; Stephan, Ryan A.

    2010-01-01

    Phase change materials (PCM) may be useful for thermal control systems that involve cyclical heat loads or cyclical thermal environments such as Low Earth Orbit (LEO) and Low Lunar Orbit (LLO). Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. One advantage that PCM's have over evaporators in this scenario is that they do not use a consumable. Wax PCM units have been baselined for the Orion thermal control system and also provide risk mitigation for the Altair Lander. However, the use of water as a PCM has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. An ice PCM heat exchanger that replicates the thermal energy storage capacity of an existing wax PCM unit was fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion are investigated. This paper presents the results to date of this investigation. Nomenclature

  4. Numerical heat transfer studies of the fatty acids for different heat exchanger materials on the performance of a latent heat storage system

    Energy Technology Data Exchange (ETDEWEB)

    Atul Sharma; Lee Dong Won; Jun Un Park [Korea Institute of Energy Research, Daejeon (Korea). Solar Thermal Research Centre; Buddhi, D. [Devi Ahilya University, Indore (India). Thermal Energy Storage Laboratory

    2005-11-01

    Theoretical investigations of fatty acids as a phase change material (PCM) for energy storage system have been conducted in this study. The selected fatty acids were capric acid, lauric acid, myristic acid, palmitic acid and stearic acid. For the two-dimensional simulation model based on the enthalpy approach, calculations have been made for the melt fraction with conduction only. Glass, stainless steel, tin, aluminium mixed, aluminium and copper were used as heat exchanger materials in the numerical calculations. Theoretical results show that capric acid was found good compatibility with latent heat storage system. The large value of thermal conductivity of heat exchanger materials did not make significant contribution on the melt fraction. (author)

  5. Novel hybrid materials based on the vanadium oxide nanobelts

    Energy Technology Data Exchange (ETDEWEB)

    Zabrodina, G.S., E-mail: kudgs@mail.ru [G.A. Razuvaev Institute of Organometallic Chemistry of Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Lobachevsky State University, Nizhny Novgorod 603950 (Russian Federation); Makarov, S.G.; Kremlev, K.V. [G.A. Razuvaev Institute of Organometallic Chemistry of Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Lobachevsky State University, Nizhny Novgorod 603950 (Russian Federation); Yunin, P.A.; Gusev, S.A. [Institute for Physics of Microstructures Russian Academy of Sciences, Nizhny Novgorod 603087 (Russian Federation); Kaverin, B.S.; Kaverina, L.B. [G.A. Razuvaev Institute of Organometallic Chemistry of Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Ketkov, S.Yu. [G.A. Razuvaev Institute of Organometallic Chemistry of Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Lobachevsky State University, Nizhny Novgorod 603950 (Russian Federation)

    2016-04-15

    Graphical abstract: - Highlights: • Flat and curved vanadium oxide nanobelts have been synthesized. • Hybrid material was prepared via decoration of flexible nanobelts with zinc phthalocyanine. • Investigations of the thermal stability, morphologies and structures were carried out. - Abstract: Novel hybrid materials based on zinc phthalocyanine and nanostructured vanadium oxides have attracted extensive attention for the development of academic research and innovative industrial applications such as flexible electronics, optical sensors and heterogeneous catalysts. Vanadium oxides nanobelts were synthesized via a hydrothermal treatment V{sub 2}O{sub 5}·nH{sub 2}O gel with surfactants (TBAB, CTAB) used as structure-directing agents, where CTAB – cetyltrimethylammonium bromide, TBAB – tetrabutylammonium bromide. Hybrid materials were prepared decoration of (CTA){sub 0.33}V{sub 2}O{sub 5} flexible nanobelts with cationic zinc phthalocyanine by the ion-exchange route. Investigations of the thermal stability, morphologies and structures of the (CTA){sub 0.33}V{sub 2}O{sub 5}, (TBA){sub 0.16}V{sub 2}O{sub 5} nanobelts and zinc phthalocyanine exchange product were carried out. The hybrid materials based on the nanostructured vanadium oxide and zinc phthalocyanine were tested as photocatalysts for oxidation of citronellol and 2-mercaptoethanol by dioxygen.

  6. Paints based on renewable materials

    OpenAIRE

    Olive, Gilles; Richel, Aurore

    2014-01-01

    National audience; Paints, at the coating meaning, are known since a long time. Typically, paint is a dispersion of one or more powders (pigments and fillers) in a macromolecular substance ("resin"), called film-forming material, diluted in solvents. Pigments are solid particles, used to give opacity and/or color. Today almost all pigments have a synthetic origin. The fillers are often natural compounds. Unlike pigments, fillers have low opacity and are colorless. These very cheap products ac...

  7. Melanin-Based Functional Materials

    OpenAIRE

    Marco d’Ischia

    2018-01-01

    Melanin biopolymers are currently the focus of growing interest for a broad range of applications at the cutting edge of biomedical research and technology. This Special Issue presents a collection of papers dealing with melanin-type materials, e.g., polydopamine, for classic and innovative applications, offering a stimulating perspective of current trends in the field. Besides basic scientists, the Special Issue is directed to researchers from industries and companies that are willing to inv...

  8. Data Exchange over Web-based Applications with DXL

    NARCIS (Netherlands)

    van Zwol, Roelof; Fokkinga, M.M.; Jeronimus, V.; Jeronimus, V.N.; Apers, Peter M.G.; Lacroix, Z.

    2002-01-01

    With large volumes of data being exchanged on the Internet, query languages are needed to bridge the gap between databases and the web. Furthermore, the differentiation in data types used by webbased applications is ever growing, despite all standardization efforts. The Data eXchange Language (DXL)

  9. Development of starch-based materials

    NARCIS (Netherlands)

    Habeych Narvaez, E.A.

    2009-01-01

    Starch-based materials show potential as fully degradable plastics. However, the current applicability of these materials is limited due to their poor moisture tolerance and mechanical properties. Starch is therefore frequently blended with other polymers to make the material more suitable for

  10. The Empirical Research of the Impact of GDP and Exchange Rate on Foreign Exchange Reserve Scale in China-Based on Quantile Regression Model

    OpenAIRE

    Lu Fang-Yuan; Shi Jun-Guo

    2013-01-01

    Based on the relevant data from 1985 to 2010, this thesis uses a quantile regression model to make an empirical research about the effect of GDP and exchange rate on foreign exchange reserve. The findings show that: Both GDP and exchange rate have a remarkable influence on the size of foreign exchange reserve and the effect of exchange rate on foreign exchange reserve is higher than GDP at mean place and middle and lower quantile, smaller than GDP at higher quantile. At all the examined quant...

  11. Melanin-Based Functional Materials.

    Science.gov (United States)

    d'Ischia, Marco

    2018-01-12

    Melanin biopolymers are currently the focus of growing interest for a broad range of applications at the cutting edge of biomedical research and technology. This Special Issue presents a collection of papers dealing with melanin-type materials, e.g., polydopamine, for classic and innovative applications, offering a stimulating perspective of current trends in the field. Besides basic scientists, the Special Issue is directed to researchers from industries and companies that are willing to invest in melanin research for innovative and inspiring solutions.

  12. Melanin-Based Functional Materials

    Directory of Open Access Journals (Sweden)

    Marco d’Ischia

    2018-01-01

    Full Text Available Melanin biopolymers are currently the focus of growing interest for a broad range of applications at the cutting edge of biomedical research and technology. This Special Issue presents a collection of papers dealing with melanin-type materials, e.g., polydopamine, for classic and innovative applications, offering a stimulating perspective of current trends in the field. Besides basic scientists, the Special Issue is directed to researchers from industries and companies that are willing to invest in melanin research for innovative and inspiring solutions.

  13. Materiality in a practice-based approach

    DEFF Research Database (Denmark)

    Svabo, Connie

    2009-01-01

    The paper provides an overview of the vocabulary for materiality which is used by practice-based approaches to organizational knowing. Common terms for materiality are 'artifact' and 'object'. The interaction between social and material realities is grasped as several processes: object......-oriented activity, symbolization, embodiment, performance, alignment and mediation. Material artifacts both stabilize and destabilize organizational action. They may ensure coordination, communication, and control, but they may also create disturbance and conflict....

  14. A novel silica based click lysine anion exchanger for ion exchange chromatography.

    Science.gov (United States)

    Guo, Hongyue; Chu, Changhu; Li, Yan; Yang, Bingcheng; Liang, Xinmiao

    2011-12-21

    Ion chromatography (IC) is one of the most powerful analysis technologies for the determination of charged compounds. A novel click lysine stationary phase was prepared via Cu(I) catalyzed alkyne-azide 1,3-dipolar cycloaddition (CuAAC) and applied to the analysis of inorganic ions. The chromatographic evaluation demonstrated good performance (e.g. the plate number of thiocyanate is ∼50,000 plates m(-1)) and effective separation ability for the common inorganic anions with aqueous Na(2)SO(4) eluent. The separation mechanism was observed to be mainly dominated by ion exchange interaction. The retention of these analytes is highly dependent on the pH value of eluent. Compared with the lysine stationary phase prepared via the conventional manner, the click lysine exchanger demonstrated shorter retention time and better ion separation characteristics under the same chromatographic conditions, which is a great advantage for rapid separation and analysis of inorganic ions.

  15. Graphene-based materials for tissue engineering.

    Science.gov (United States)

    Shin, Su Ryon; Li, Yi-Chen; Jang, Hae Lin; Khoshakhlagh, Parastoo; Akbari, Mohsen; Nasajpour, Amir; Zhang, Yu Shrike; Tamayol, Ali; Khademhosseini, Ali

    2016-10-01

    Graphene and its chemical derivatives have been a pivotal new class of nanomaterials and a model system for quantum behavior. The material's excellent electrical conductivity, biocompatibility, surface area and thermal properties are of much interest to the scientific community. Two-dimensional graphene materials have been widely used in various biomedical research areas such as bioelectronics, imaging, drug delivery, and tissue engineering. In this review, we will highlight the recent applications of graphene-based materials in tissue engineering and regenerative medicine. In particular, we will discuss the application of graphene-based materials in cardiac, neural, bone, cartilage, skeletal muscle, and skin/adipose tissue engineering. We will also discuss the potential risk factors of graphene-based materials in tissue engineering. In conclusion, we will outline the opportunities in the usage of graphene-based materials for clinical applications. Published by Elsevier B.V.

  16. LDEF materials special investigation group's data bases

    Science.gov (United States)

    Strickland, John W.; Funk, Joan G.; Davis, John M.

    1993-01-01

    The Long Duration Exposure Facility (LDEF) was composed of and contained a wide array of materials, representing the largest collection of materials flown for space exposure and returned for ground-based analyses to date. The results and implications of the data from these materials are the foundation on which future space missions will be built. The LDEF Materials Special Investigation Group (MSIG) has been tasked with establishing and developing data bases to document these materials and their performance to assure not only that the data are archived for future generations but also that the data are available to the space user community in an easily accessed, user-friendly form. The format and content of the data bases developed or being developed to accomplish this task are discussed. The hardware and software requirements for each of the three data bases are discussed along with current availability of the data bases.

  17. Agents Based e-Commerce and Securing Exchanged Information

    Science.gov (United States)

    Al-Jaljouli, Raja; Abawajy, Jemal

    Mobile agents have been implemented in e-Commerce to search and filter information of interest from electronic markets. When the information is very sensitive and critical, it is important to develop a novel security protocol that can efficiently protect the information from malicious tampering as well as unauthorized disclosure or at least detect any malicious act of intruders. In this chapter, we describe robust security techniques that ensure a sound security of information gathered throughout agent’s itinerary against various security attacks, as well as truncation attacks. A sound security protocol is described, which implements the various security techniques that would jointly prevent or at least detect any malicious act of intruders. We reason about the soundness of the protocol usingSymbolic Trace Analyzer (STA), a formal verification tool that is based on symbolic techniques. We analyze the protocol in key configurations and show that it is free of flaws. We also show that the protocol fulfils the various security requirements of exchanged information in MAS, including data-integrity, data-confidentiality, data-authenticity, origin confidentiality and data non-repudiability.

  18. High temperature corrosion of advanced ceramic materials for hot gas filters and heat exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Crossland, C.E.; Shelleman, D.L.; Spear, K.E. [Pennsylvania State Univ., University Park, PA (United States)] [and others

    1996-08-01

    A vertical flow-through furnace has been built to study the effect of corrosion on the morphology and mechanical properties of ceramic hot gas filters. Sections of 3M Type 203 and DuPont Lanxide SiC-SiC filter tubes were sealed at one end and suspended in the furnace while being subjected to a simulated coal combustion environment at 870{degrees}C. X-ray diffraction and electron microscopy is used to identify phase and morphology changes due to corrosion while burst testing determines the loss of mechanical strength after exposure to the combustion gases. Additionally, a thermodynamic database of gaseous silicon compounds is currently being established so that calculations can be made to predict important products of the reaction of the environment with the ceramics. These thermodynamic calculations provide useful information concerning the regimes where the ceramic may be degraded by material vaporization. To verify the durability and predict lifetime performance of ceramic heat exchangers in coal combustion environments, long-term exposure testing of stressed (internally pressurized) tubes must be performed in actual coal combustion environments. The authors have designed a system that will internally pressurize 2 inch OD by 48 inch long ceramic heat exchanger tubes to a maximum pressure of 200 psi while exposing the outer surface of the tubes to coal combustion gas at the Combustion and Environmental Research Facility (CERF) at the Pittsburgh Energy and Technology Center. Water-cooled, internal o-ring pressure seals were designed to accommodate the existing 6 inch by 6 inch access panels of the CERF. Tubes will be exposed for up to a maximum of 500 hours at temperatures of 2500 and 2600{degrees}F with an internal pressure of 200 psi. If the tubes survive, their retained strength will be measured using the high temperature tube burst test facility at Penn State University. Fractographic analysis will be performed to identify the failure source(s) for the tubes.

  19. New Cork-Based Materials and Applications

    Directory of Open Access Journals (Sweden)

    Luís Gil

    2015-02-01

    Full Text Available This review work is an update of a previous work reporting the new cork based materials and new applications of cork based materials. Cork is a material which has been used for multiple applications. The most known uses of cork are in stoppers (natural and agglomerated cork for alcoholic beverages, classic floor covering with composite cork tiles (made by the binding of cork particles with different binders, and thermal/acoustic/vibration insulation with expanded corkboard in buildings and some other industrial fields. Many recent developments have been made leading to new cork based materials. Most of these newly developed cork materials are not yet on the market, but they represent new possibilities for engineers, architects, designers and other professionals which must be known and considered, potentially leading to their industrialization. This paper is a review covering the last five years of innovative cork materials and applications also mentioning previous work not reported before.

  20. New Cork-Based Materials and Applications.

    Science.gov (United States)

    Gil, Luís

    2015-02-10

    This review work is an update of a previous work reporting the new cork based materials and new applications of cork based materials. Cork is a material which has been used for multiple applications. The most known uses of cork are in stoppers (natural and agglomerated cork) for alcoholic beverages, classic floor covering with composite cork tiles (made by the binding of cork particles with different binders), and thermal/acoustic/vibration insulation with expanded corkboard in buildings and some other industrial fields. Many recent developments have been made leading to new cork based materials. Most of these newly developed cork materials are not yet on the market, but they represent new possibilities for engineers, architects, designers and other professionals which must be known and considered, potentially leading to their industrialization. This paper is a review covering the last five years of innovative cork materials and applications also mentioning previous work not reported before.

  1. Simulation and experimental study on thermal optimization of the heat exchanger for automotive exhaust-based thermoelectric generators

    Directory of Open Access Journals (Sweden)

    C.Q. Su

    2014-11-01

    Full Text Available Thermoelectric technology has revealed the potential for automotive exhaust-based thermoelectric generator (TEG, which contributes to the improvement of the fuel economy of the engine-powered vehicle. As a major factor, thermal capacity and heat transfer of the heat exchanger affect the performance of TEG effectively. With the thermal energy of exhaust gas harvested by thermoelectric modules, a temperature gradient appears on the heat exchanger surface, so as the interior flow distribution of the heat exchanger. In order to achieve uniform temperature distribution and higher interface temperature, the thermal characteristics of heat exchangers with various heat transfer enhancement features are studied, such as internal structure, material and surface area. Combining the computational fluid dynamics simulations and infrared test on a high-performance engine with a dynamometer, the thermal performance of the heat exchanger is evaluated. Simulation and experiment results show that a plate-shaped heat exchanger made of brass with accordion-shaped internal structure achieves a relatively ideal performance, which can practically improve overall thermal performance of the TEG.

  2. Material-based figure of merit for caloric materials

    Science.gov (United States)

    Griffith, L. D.; Mudryk, Y.; Slaughter, J.; Pecharsky, V. K.

    2018-01-01

    The efficient use of reversible thermal effects in magnetocaloric, electrocaloric, and elastocaloric materials is a promising avenue that can lead to a substantially increased efficiency of refrigeration and heat pumping devices, most importantly, those used in household and commercial cooling applications near ambient temperature. A proliferation in caloric material research has resulted in a wide array of materials where only the isothermal change in entropy in response to a handful of different field strengths over a limited range of temperatures has been evaluated and reported. Given the abundance of such data, there is a clear need for a simple and reliable figure of merit enabling fast screening and down-selection to justify further detailed characterization of those material systems that hold the greatest promise. Based on the analysis of several well-known materials that exhibit vastly different magnetocaloric effects, the Temperature averaged Entropy Change is introduced as a suitable early indicator of the material's utility for magnetocaloric cooling applications, and its adoption by the caloric community is recommended.

  3. RSA-Based Password-Authenticated Key Exchange, Revisited

    Science.gov (United States)

    Shin, Seonghan; Kobara, Kazukuni; Imai, Hideki

    The RSA-based Password-Authenticated Key Exchange (PAKE) protocols have been proposed to realize both mutual authentication and generation of secure session keys where a client is sharing his/her password only with a server and the latter should generate its RSA public/private key pair (e, n), (d, n) every time due to the lack of PKI (Public-Key Infrastructures). One of the ways to avoid a special kind of off-line (so called e-residue) attacks in the RSA-based PAKE protocols is to deploy a challenge/response method by which a client verifies the relative primality of e and φ(n) interactively with a server. However, this kind of RSA-based PAKE protocols did not give any proof of the underlying challenge/response method and therefore could not specify the exact complexity of their protocols since there exists another security parameter, needed in the challenge/response method. In this paper, we first present an RSA-based PAKE (RSA-PAKE) protocol that can deploy two different challenge/response methods (denoted by Challenge/Response Method1 and Challenge/Response Method2). The main contributions of this work include: (1) Based on the number theory, we prove that the Challenge/Response Method1 and the Challenge/Response Method2 are secure against e-residue attacks for any odd prime e (2) With the security parameter for the on-line attacks, we show that the RSA-PAKE protocol is provably secure in the random oracle model where all of the off-line attacks are not more efficient than on-line dictionary attacks; and (3) By considering the Hamming weight of e and its complexity in the. RSA-PAKE protocol, we search for primes to be recommended for a practical use. We also compare the RSA-PAKE protocol with the previous ones mainly in terms of computation and communication complexities.

  4. F- and H-Area Seepage Basins Water Treatment System Process Optimization and Alternative Chemistry Ion Exchange/Sorbent Material Screening Clearwell Overflow Study

    Energy Technology Data Exchange (ETDEWEB)

    Serkiz, S.M.

    2000-08-30

    This study investigated alternative ion exchange/sorbent materials and polishing chemistries designed to remove specific radionuclides not removed during the neutralization/precipitation/clarification process.

  5. Seminar Cum Meeting Report: Codata Task Group for Exchangeable Material Data Representation to Support Research and Education

    Directory of Open Access Journals (Sweden)

    T Ashino

    2008-11-01

    Full Text Available On March 4-5, 2008, the CODATA Task Group for Exchangeable Material Data Representation to Support Research and Education held a two day seminar cum meeting at the National Physical Laboratory (NPL, New Delhi, India, with NPL materials researchers and task group members representing material activities and databases from seven countries: European Union (The Czech Republic, France, and the Netherlands, India, Korea, Japan, and the United States. The NPL seminar included presentations about the researchers' work. The Task Group meeting included presentations about current data related activities of the members. Joint discussions between NPL researchers and CODATA task group members began an exchange of viewpoints among materials data producers, users, and databases developers. The seminar cum meeting included plans to continue and expand Task Group activities at the 2008 CODATA 21st Meeting in Kyiv, Ukraine.

  6. Study of thermal accumulators-exchangers containing low temperature (20-80c) phase transformation materials

    Energy Technology Data Exchange (ETDEWEB)

    Lecomte, D.

    1983-06-01

    After a review of the various types of heat exchanger technologies (especially the tube and plate types), an analytical and experimental study of a rotating cylinder dynamical accumulator-exchanger is presented and extended to a larger scale accumulator. The various analytical and numerical methods for the resolution of the heat equation in a diphasic medium and the problems caused by the presence of an exchanger and by the natural convection are described. Two approaches for the immersed tubular exchangers are compared and used to modelize a real storage system. A dimensioning procedure is then proposed.

  7. Graphene oxide based nanohybrid proton exchange membranes for fuel cell applications: An overview.

    Science.gov (United States)

    Pandey, Ravi P; Shukla, Geetanjali; Manohar, Murli; Shahi, Vinod K

    2017-02-01

    In the context of many applications, such as polymer composites, energy-related materials, sensors, 'paper'-like materials, field-effect transistors (FET), and biomedical applications, chemically modified graphene was broadly studied during the last decade, due to its excellent electrical, mechanical, and thermal properties. The presence of reactive oxygen functional groups in the grapheme oxide (GO) responsible for chemical functionalization makes it a good candidate for diversified applications. The main objectives for developing a GO based nanohybrid proton exchange membrane (PEM) include: improved self-humidification (water retention ability), reduced fuel crossover (electro-osmotic drag), improved stabilities (mechanical, thermal, and chemical), enhanced proton conductivity, and processability for the preparation of membrane-electrode assembly. Research carried on this topic may be divided into protocols for covalent grafting of functional groups on GO matrix, preparation of free-standing PEM or choice of suitable polymer matrix, covalent or hydrogen bonding between GO and polymer matrix etc. Herein, we present a brief literature survey on GO based nano-hybrid PEM for fuel cell applications. Different protocols were adopted to produce functionalized GO based materials and prepare their free-standing film or disperse these materials in various polymer matrices with suitable interactions. This review article critically discussed the suitability of these PEMs for fuel cell applications in terms of the dependency of the intrinsic properties of nanohybrid PEMs. Potential applications of these nanohybrid PEMs, and current challenges are also provided along with future guidelines for developing GO based nanohybrid PEMs as promising materials for fuel cell applications. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Material Studies Related to the Use of NaK Heat Exchangers Coupled to Stirling Heater Heads

    Science.gov (United States)

    Locci, Ivan E.; Bowman, Cheryl L.; Geng, Steven M.; Robbie, Malcolm G.

    2011-01-01

    NASA has been supporting design studies and technology development that could provide power to an outpost on the Moon, Mars, or an asteroid. Technology development efforts have included fabrication and evaluation of components used in a Stirling engine power conversion system. Destructive material evaluation was performed on a NaK shell heat exchanger that was developed by the NASA Glenn Research Center (GRC) and integrated with a commercial 1 kWe Stirling convertor from Sunpower Incorporated. The NaK Stirling test demonstrated Stirling convertor electrical power generation using a pumped liquid metal heat source under thermal conditions that represent the heat exchanger liquid metal loop in a Fission Power Systems (FPS) reactor. The convertors were operated for a total test time of 66 hr at a maximum temperature of 823 K. After the test was completed and NaK removed, the heat exchanger assembly was sectioned to evaluate any material interactions with the flowing liquid metal. Several dissimilar-metal braze joint options, crucial for the heat exchanger transfer path, were also investigated. A comprehensive investigation was completed and lessons learned for future heat exchanger development efforts are discussed.

  9. Graphene based materials: Enhancing solar energy harvesting

    Energy Technology Data Exchange (ETDEWEB)

    Gua, Chun Xian; Guai, Guan Hong; Li, Chang Ming [Nanyang Tecnological Univ., Singapore (Singapore). Center for Advanded Bioanaosystems

    2011-05-15

    Due to their excellent electronic and physiochemical properties, graphene based materials have been extensively explored for solar energy harvesting as either electron and hole transport materials, buffer layers, or window and counter electrodes. This research news surveys very recent advances in this emerging field with emphasis on fundamental understanding of their enhancement mechanism, while discussing future challenges.

  10. Promoting Scientific Transparency to Facilitate the Safe and Open International Exchange of Biological Materials and Electronic Data

    Directory of Open Access Journals (Sweden)

    Kenneth B. Yeh

    2017-10-01

    Full Text Available Scientific communication, collaboration and progress are enhanced through the exchange of data, materials and ideas. Recent advances in technology, commercial proprietary discovery and current local and global events (e.g., emerging human, animal and plant disease outbreaks have increased the demand, and shortened optimal timelines for material and data exchange, both domestically and internationally. Specific circumstances in each case, such as the type of material being transferred (i.e., select agent, disease-causing agent and assessed biosafety risk level and current events, dictate the level of agreements and requirements. Recent lessons learned from emerging disease issues and emergencies have demonstrated that human engagement and increased science diplomacy are needed to reinforce and sustain biosafety and biosecurity practices and processes, for better scientific transparency. A reasonable and accepted framework of guidance for open sharing of data and materials is needed that can be applied on multiple cooperative levels, including global and national. Although numerous agreement variations already exist for the exchange of materials and data, regulations to guide the development of both the language and implementation of such agreements are limited. Without such regulations, scientific exchange is often restricted, limiting opportunities for international capacity building, collaboration and cooperation. In this article, we present and discuss several international case histories that illustrate the complex nature of scientific exchange. Recommendations are made for a dual bottom-up and top-down approach that includes all stakeholders from beginning negotiation stages to emphasize trust and cooperation. The broader aim of this approach is to increase international scientific transparency and trust in a safe and open manner, supporting increased global one health security.

  11. Nosehouse: heat-conserving ventilators based on nasal counterflow exchangers.

    Science.gov (United States)

    Vogel, Steven

    2009-12-01

    Small birds and mammals commonly minimize respiratory heat loss with reciprocating counterflow exchangers in their nasal passageways. These animals extract heat from the air in an exhalation to warm those passageways and then use that heat to warm the subsequent inhalation. Although the near-constant volume of buildings precludes direct application of the device, a pair of such exchangers located remotely from each other circumvents that problem. A very simple and crudely constructed small-scale physical model of the device worked well enough as a heat conserver to suggest utility as a ventilator for buildings.

  12. Functional materials based on nanocrystalline cellulose

    Science.gov (United States)

    Surov, O. V.; Voronova, M. I.; Zakharov, A. G.

    2017-10-01

    The data on the synthesis of functional materials based on nanocrystalline cellulose (NCC) published over the past 10 years are analyzed. The liquid-crystal properties of NCC suspensions, methods of investigation of NCC suspensions and films, conditions for preserving chiral nematic structure in the NCC films after removal of the solvent and features of templated sol–gel synthesis of functional materials based on NCC are considered. The bibliography includes 106 references.

  13. Whole Language-Based English Reading Materials

    Directory of Open Access Journals (Sweden)

    Dian Erlina

    2016-05-01

    Full Text Available This Research and Development (R&D aims at developing English reading materials for undergraduate EFL students of Universitas Islam Negeri (UIN Raden Fatah Palembang, Indonesia. Research data were obtained through questionnaires, tests, and documents. The results of the research show that the existing materials are not relevant to the students’ need, so there is a need for developing new materials based on whole language principles. In general, the new developed materials are considered reliable by the experts, students, and lecturers. The materials are also effective in improving students’ reading achievement. The final product of the materials consists of a course book entitled Whole Language Reading (WLR and a teacher’s manual. WLR provides rich input of reading strategies, variety of topics, concepts, texts, activities, tasks, and evaluations. Using this book makes reading more holistic and meaningful as it provides integration across language skills and subject areas.

  14. [Progress of alginate-based biomedical materials].

    Science.gov (United States)

    Wei, Xiaojuan; Xi, Tingfei; Gu, Qisheng; Zheng, Yufeng

    2013-08-01

    To review the current situation of alginate-based biomedical materials, especially focus on the clinical strategies and research progress in the clinical applications and point out several key issues that should be concerned about. Based on extensive investigation of domestic and foreign alginate-based biomedical materials research and related patent, literature, and medicine producted, the paper presented the comprehensive analysis of its research and development, application status, and then put forward several new research directions which should be focused on. Alginate-based biomedical materials have been widely used in clinical field with a number of patients, but mainly in the fields of wound dressings and dental impression. Heart failure treatment, embolization, tissue engineering, and stem cells culture are expected to become new directions of research and products development. Development of alginate-based new products has good clinical feasibility and necessity, but a lot of applied basic researches should be carried out in the further investigations.

  15. The Effectiveness of Web-Based Foreign Exchange Trading Simulation in an International Finance Course

    Science.gov (United States)

    Chou, Chen-Huei; Liu, Hao-Chen

    2013-01-01

    The purpose of this article is to study if trading simulation is an effective tool to increase students' knowledge of the foreign exchange market. We developed a real-time multiuser web-based trading system that replicates an electronic brokerage foreign exchange market. To assess the effectiveness of the program, we conducted surveys in three…

  16. Web-Based Knowledge Exchange through Social Links in the Workplace

    Science.gov (United States)

    Filipowski, Tomasz; Kazienko, Przemyslaw; Brodka, Piotr; Kajdanowicz, Tomasz

    2012-01-01

    Knowledge exchange between employees is an essential feature of recent commercial organisations on the competitive market. Based on the data gathered by various information technology (IT) systems, social links can be extracted and exploited in knowledge exchange systems of a new kind. Users of such a system ask their queries and the system…

  17. Land-use change arising from rural land exchange : an agent-based simulation model

    NARCIS (Netherlands)

    Bakker, Martha M.; Alam, Shah Jamal; van Dijk, Jerry; Rounsevell, Mark D. A.

    Land exchange can be a major factor driving land-use change in regions with high pressure on land, but is generally not incorporated in land-use change models. Here we present an agent-based model to simulate land-use change arising from land exchange between multiple agent types representing

  18. Land-use change arising from rural land exchange: an agent-based simulation model

    NARCIS (Netherlands)

    Bakker, M.M.; Alam, S.J.; Dijk, van J.; Rounsevell, M.D.A.

    2015-01-01

    Land exchange can be a major factor driving land-use change in regions with high pressure on land, but is generally not incorporated in land-use change models. Here we present an agent-based model to simulate land-use change arising from land exchange between multiple agent types representing

  19. Microcalorimetric study of adsorption of human monoclonal antibodies on cation exchange chromatographic materials.

    Science.gov (United States)

    Dieterle, Michael; Blaschke, Tim; Hasse, Hans

    2008-09-26

    Adsorption of two human monoclonal antibodies on two different strong cation exchange resins is studied by isothermal titration microcalorimetry and independent adsorption isotherm measurements. The pH value is varied between 4.5 and 7.0, using different buffer systems, the temperature is always 25 degrees C. The adsorption isotherm data is fitted using two different Langmuir type models. Combining the calorimetric and the adsorption data, the specific enthalpy of adsorption of the protein Deltah(p)(ads) is determined. At pH values near 7.0, where the antibodies are only weakly charged, the adsorption is exothermal. At small loadings the absolute number of Deltah(p)(ads) is then large and almost constant but it significantly decreases at higher loadings. This shows that the arrangement of antibody molecules on the absorber material depends on the loading and is less favourable at higher loadings. Despite the high positive charge of the antibody at pH values of about 5 the value of Deltah(p)(ads) is almost zero along the entire isotherm. Furthermore, at pH 4.5 even endothermal effects are observed, although high binding capacities are found. At these conditions the adsorption process seems to be strongly influenced by the ions bound to the antibody. Their release upon absorption explains the endothermal caloric effect. The adsorption equilibrium constant K(eq) is calculated from the isotherms. From Deltag(p)(ads) and the calorimetric results for Deltah(p)(ads), Deltas(p)(ads), the entropy change upon adsorption of the protein is found for the different studied conditions.

  20. Extensive homoeologous genome exchanges in allopolyploid crops revealed by mRNAseq-based visualization.

    Science.gov (United States)

    He, Zhesi; Wang, Lihong; Harper, Andrea L; Havlickova, Lenka; Pradhan, Akshay K; Parkin, Isobel A P; Bancroft, Ian

    2017-05-01

    Polyploidy, the possession of multiple sets of chromosomes, has been a predominant factor in the evolution and success of the angiosperms. Although artificially formed allopolyploids show a high rate of genome rearrangement, the genomes of cultivars and germplasm used for crop breeding were assumed stable and genome structural variation under the artificial selection process of commercial breeding has remained little studied. Here, we show, using a repurposed visualization method based on transcriptome sequence data, that genome structural rearrangement occurs frequently in varieties of three polyploid crops (oilseed rape, mustard rape and bread wheat), meaning that the extent of genome structural variation present in commercial crops is much higher than expected. Exchanges were found to occur most frequently where homoeologous chromosome segments are collinear to telomeres and in material produced as doubled haploids. The new insights into genome structural evolution enable us to reinterpret the results of recent studies and implicate homoeologous exchanges, not deletions, as being responsible for variation controlling important seed quality traits in rapeseed. Having begun to identify the extent of genome structural variation in polyploid crops, we can envisage new strategies for the global challenge of broadening crop genetic diversity and accelerating adaptation, such as the molecular identification and selection of genome deletions or duplications encompassing genes with trait-controlling dosage effects. © 2016 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  1. Triarylborane-Based Materials for OLED Applications

    Directory of Open Access Journals (Sweden)

    Gulsen Turkoglu

    2017-09-01

    Full Text Available Multidisciplinary research on organic fluorescent molecules has been attracting great interest owing to their potential applications in biomedical and material sciences. In recent years, electron deficient systems have been increasingly incorporated into fluorescent materials. Triarylboranes with the empty p orbital of their boron centres are electron deficient and can be used as strong electron acceptors in conjugated organic fluorescent materials. Moreover, their applications in optoelectronic devices, energy harvesting materials and anion sensing, due to their natural Lewis acidity and remarkable solid-state fluorescence properties, have also been investigated. Furthermore, fluorescent triarylborane-based materials have been commonly utilized as emitters and electron transporters in organic light emitting diode (OLED applications. In this review, triarylborane-based small molecules and polymers will be surveyed, covering their structure-property relationships, intramolecular charge transfer properties and solid-state fluorescence quantum yields as functional emissive materials in OLEDs. Also, the importance of the boron atom in triarylborane compounds is emphasized to address the key issues of both fluorescent emitters and their host materials for the construction of high-performance OLEDs.

  2. Steric effect involved in Ln3+/Ce3+ exchange in a coordination polymer based on di(2-ethylhexyl)phosphoric acid.

    Science.gov (United States)

    Tasaki-Handa, Yuiko; Abe, Yukie; Ooi, Kenta; Tanaka, Mikiya; Wakisaka, Akihiro

    2014-01-28

    Coordination polymers can be attractive ion exchange materials because of their crystallinity and semi-flexibility, which are rather opposing properties, and play integral and synergistic roles in introducing unique ion-exchange behavior. In this paper, Ln(3+)/Ce(3+) exchange (Ln(3+) = Nd(3+), Gd(3+), Dy(3+), or Lu(3+)) in a coordination polymer, [Ce(dehp)3], based on di(2-ethylhexyl)phosphoric acid (Hdehp) is studied by distribution coefficient measurements, ion-exchange isotherms, Kielland plot analysis, and morphology observation. The ion-exchange selectivity is in the order Nd(3+) dissolution-recrystallization. The small steric strain in the Nd(3+)/Ce(3+) system leads to the formation of a Nd(3+)-and-Ce(3+) solid-solution, whereas the morphological change is possibly restrained by the strong strain caused by loaded Ln(3+) with an ionic size significantly smaller than the original Ce(3+).

  3. Atmosphere-ocean gas exchange based on radiocarbon data

    Science.gov (United States)

    Byalko, Alexey

    2014-05-01

    In recent decades, the intensity of global atmospheric convection has accelerated faster than climate warming; it is possible to judge this process from indirect data. Increasing ocean salinity contrasts provide evidence that evaporation has intensified [1]; sea surface wind velocities and wave heights have increased [2]. The CO2 gas exchange between the atmosphere and ocean must also simultaneously increase. Monthly measurements of atmospheric CO2 concentration have been published since 1958 [3], but directly measuring its fluxes from the atmosphere to the ocean and back is hardly possible. We show they can be reconstructed from 14C isotope concentration data. In the past century, two processes influenced the atmospheric 14C concentration in opposite directions: burning fossil fuels and testing nuclear weapons in the atmosphere. We compare the gas exchange theory with measurements of radiocarbon content in the atmosphere [4—6], which allows assessing the gas exchange quantitatively for the ocean to atmosphere and atmosphere to ocean fluxes separately for period 1960—2010 [7]. References 1. Durack P. J. and Wijffels S. E., J. Climate 23, 4342 (2010). 2. Young I. R., Sieger S., and Babanin A.V., Science 332, 451 (2011). 3. NOAA Earth System Research Laboratory Data: ftp://ftp.cmdl.noaa.gov/ccg/co2/trends/co2_mm_mlo.txt. 4. Nydal R., Lövseth K. // J. Geophys. Res. 1983. V. 88. P. 3579. 5. Levin I., Kromer B. // Radiocarbon. 1997. V. 39. P. 205. 6. Miller J.B., Lehman S.J., Montzka S.A., et al. // J. Geophys. Res. 2012. V. 117. D08302. 7. Byalko A.V. Doklady Physics, 2013. V. 58, 267-271.

  4. Dataset for Probabilistic estimation of residential air exchange rates for population-based exposure modeling

    Data.gov (United States)

    U.S. Environmental Protection Agency — This dataset provides the city-specific air exchange rate measurements, modeled, literature-based as well as housing characteristics. This dataset is associated with...

  5. A microprocessor-based system for measurement of gas exchange.

    Science.gov (United States)

    Jaffe, M B; Frick, G; Wilson, D; Johnston, M; Reid, H; Foster, S; Norton, A C

    1984-10-01

    The basic physical measurements for determining gas exchange are difficult to make accurately even in a well-equipped, human-performance laboratory with experienced personnel. A fully automated system has been developed to achieve the accuracy of standard laboratory measurements. The application of this instrument extends from critical care to stress-testing. Real-time, multitasking software integrates the data collected from several transducers and analyzers and calculates up to several dozen physiological variables, which are range-checked for reasonableness. The operator is provided with user-friendly means to tailor the data-reporting and- collection functions of the system to his own needs and requirements. Because the instrument is controlled by software, the functions of calibration, measurement, timing, reporting, plotting, and data quality assurance are highly cost-effective. Extensive use of formal test procedures permits verifying all systems and data reliability; it also assures meeting the desired specifications. The ease of operation and high-quality results inherent in this system make it unsurpassed in gas-exchange measurements.

  6. Autogenous Phenomena in Cement-Based Materials

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede

    This thesis has been written to obtain the Danish doctoral degree in technology, Dr.Techn. It addresses autogenous phenomena in cement-based materials - primarily deformation and change of the relative humidity (RH). In the thesis it is explained how the importance of these phenomena was identified...

  7. Ecotoxicological effects of graphene-based materials

    Science.gov (United States)

    Montagner, A.; Bosi, S.; Tenori, E.; Bidussi, M.; Alshatwi, A. A.; Tretiach, M.; Prato, M.; Syrgiannis, Z.

    2017-03-01

    Graphene-based materials (GBMs) are currently under careful examination due to their potential impact on health and environment. Over the last few years, ecotoxicology has started to analyze all the potential issues related to GBMs and their possible consequences on living organisms. These topics are critically considered in this comprehensive review along with some considerations about future perspectives.

  8. Morphology of polyethylene ski base materials.

    Science.gov (United States)

    Fischer, Jörg; Wallner, Gernot M; Pieber, Alois

    2010-03-01

    We used high-resolution Raman spectroscopy and differential scanning calorimetry for a comprehensive analysis of carbon black-filled polyethylene ski base grades at processing stages from the raw material to the structured ski base. Based on Raman mapping, we assessed the applicability of an advanced evaluation procedure for amorphous, disordered, and crystalline phase fractions of polyethylene for polyethylene extrusion and sinter grades. For sinter grades, a sufficient segregation between carbon black and polyethylene was confirmed, allowing for a comprehensive Raman spectroscopic morphological analysis. Significant morphological changes in polyethylene due to processing from the raw material to the semi-finished film and to the structured ski base were identified. Throughout the processing chain, we observed a decrease in crystallinity and an increase in the amorphous phase fraction. Although the raw material and the sintered semi-finished film exhibited a different but uniform polyethylene morphology, the morphological changes due to structuring of the ski base are limited to the top surface layer. The highest amorphous phase fractions were detected in the surface of the structured ski bases.

  9. Photodetectors based on two dimensional materials

    Science.gov (United States)

    Zheng, Lou; Zhongzhu, Liang; Guozhen, Shen

    2016-09-01

    Two-dimensional (2D) materials with unique properties have received a great deal of attention in recent years. This family of materials has rapidly established themselves as intriguing building blocks for versatile nanoelectronic devices that offer promising potential for use in next generation optoelectronics, such as photodetectors. Furthermore, their optoelectronic performance can be adjusted by varying the number of layers. They have demonstrated excellent light absorption, enabling ultrafast and ultrasensitive detection of light in photodetectors, especially in their single-layer structure. Moreover, due to their atomic thickness, outstanding mechanical flexibility, and large breaking strength, these materials have been of great interest for use in flexible devices and strain engineering. Toward that end, several kinds of photodetectors based on 2D materials have been reported. Here, we present a review of the state-of-the-art in photodetectors based on graphene and other 2D materials, such as the graphene, transition metal dichalcogenides, and so on. Project supported by the National Natural Science Foundation of China (Nos. 61377033, 61574132, 61504136) and the State Key Laboratory of Applied Optics, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences.

  10. Model-based analysis of anion-exchanger positioning in direct methanol fuel cell systems

    Science.gov (United States)

    Kraus, Maik; Schröder, Daniel; Krewer, Ulrike

    2014-09-01

    In this work we present a model based study to investigate the presence of anion exchangers in direct methanol fuel cell (DMFC) systems. It is well known that environmental or fuel impurities lead to accumulation of harmful anions, such as chloride, in the system. However, due to DMFC anodic reaction, a carbonate system is present. These corbanate anions have to be taken into account for the anion exchanger design and placement as well as for the system operation strategy with and without anion exchanger, which is the objective of this study. For this purpose, the expected amount of harmful chloride ions in a DMFC system is estimated, and that of carbonate ions is calculated with a model of the carbonate system in a DMFC system. The predicition of durability and dimensions of an anion exchanger is based on a monovalent anion exchange model. The design of gas liquid separators in the DMFC system has a major influence on the amount of dissolved carbon dioxide, which is crucial for durability and dimension of a system integrated anion exchanger. Finally, feasible positions of anion exchanger in a DMFC system are elaborated to fulfill the needs for long term and stable DMFC operation.

  11. An Investigation into the Effect of Cation-exchange on the Adsorption Performance of Indium-based Sodalite-ZMOF

    KAUST Repository

    Samin, Umer A.

    2016-04-13

    There is a pressing need for advanced solid-state materials that can be implemented in industrial gas separation processes to achieve separations with a significantly reduced energy input compared to what is typically required from current technologies. Although certain porous materials like zeolites bear some commercial significance for gas separation; their inherent lack of tunability limits the extent to which these materials may be exploited in industry. Zeolite-like Metal-Organic Frameworks (ZMOFs) are a sub-class of Metal-Organic Framework materials (MOFs) that show a structural semblance to zeolites while possessing the tunability advantages of MOF materials. ZMOFs which are topologically similar to certain zeolites can be functionalised and tuned in numerous ways to improve their gas separation properties. In this work, indium-based sod-ZMOF was tuned by cation-exchange and then characterised by different experimental tools such as single-crystal x-ray diffraction, elemental analysis and gas adsorption. It was found that various parameters like the choice of cation, the concentration of salt solution and the choice of solvent had a significant bearing on the cation-exchange of sod-ZMOF and its subsequent adsorption properties.

  12. Emergy-based energy and material metabolism of the Yellow River basin

    Science.gov (United States)

    Chen, B.; Chen, G. Q.

    2009-03-01

    The Yellow River basin is an opening ecosystem exchanging energy and materials with the surrounding environment. Based on emergy as embodied solar energy, the social energy and materials metabolism of the Yellow River basin is aggregated into emergetic equivalent to assess the level of resource depletion, environmental impact and local sustainability. A set of emergy indices are also established to manifest the ecological status of the total river basin ecosystem.

  13. Design and study of the mask exchange system based on Delta parallel mechanism

    Science.gov (United States)

    Zhang, Feifan; Wang, Jianping; Zhou, Hongfei; Zhou, Zengxiang; Chu, Jiaru

    2016-07-01

    Mask exchange system is the main part of Multi-Object Broadband Imaging Echellette (MOBIE) on the Thirty Meter Telescope (TMT). The robot is one of the key parts in the mask exchange process. In view of the facts that the scheme the on-board robot is hard to meet the requirements of TMT and the traditional industrial robot is difficult to use in the Mask Exchange System (MEX). The delta parallel mechanism has much advantages such as good dynamic performance, high speed and could integrate a vision recognition system to identify the masks. The design for MEX based on off-board Delta parallel mechanism was proposed in the paper.

  14. Land-use change arising from rural land exchange: an agent-based simulation model

    OpenAIRE

    Martha M. Bakker; Alam, Shah Jamal; van Dijk, Jerry; Rounsevell, Mark D A

    2015-01-01

    Land exchange can be a major factor driving land-use change in regions with high pressure on land, but is generally not incorporated in land-use change models. Here we present an agent-based model to simulate land-use change arising from land exchange between multiple agent types representing farmers, nature organizations, and estate owners. The RULEX model (Rural Land EXchange) was calibrated and applied to a 300 km(2) case study area in the east of the Netherlands. Decision rules about whic...

  15. High ion-exchange properties of hybrid materials from X-type zeolite and ground glass powder

    Science.gov (United States)

    Taira, Nobuyuki; Yoshida, Kohei

    2017-10-01

    Zeolites are crystalline aluminosilicates with a homogeneous distribution of micropores with a superior cation-exchange capacity. Because they have especially excellent selective exchange properties, a considerable number of studies have been conducted on treating water containing radioisotopes using the zeolites. When using artificial zeolites, they have inferior sinterability; in addition, it is quite hard for them to remove from polluted liquid since these artificial zeolites are principally synthesized as a form of powder, which is a disadvantage. In this study, hybrid materials were prepared from X-type zeolite and waste glass powder. Their ion-removal effect and mechanical strength were investigated. The zeolite and waste glass were ground in an agate mortar in several ratios. 0.5 g of the mixture was pressure-molded into pellets having a diameter of 7 mm. These pellets were slowly heated at the speed of 240°C/h to 700°C and maintained at 700°C for 2 h. The removal rate of Sr2+ ions increased as the amount of X-type zeolite in the hybrid materials increased; the former increased up to 100% when the content of latter exceeded 50%. The mechanical strength increased by increasing the amount of glass in the hybrid materials. This is attributed to the fact that the glass powder acts as a binder that improves the densification and consequently the mechanical strength of the hybrid materials.

  16. Protein-Based Drug-Delivery Materials

    Science.gov (United States)

    Jao, Dave; Xue, Ye; Medina, Jethro; Hu, Xiao

    2017-01-01

    There is a pressing need for long-term, controlled drug release for sustained treatment of chronic or persistent medical conditions and diseases. Guided drug delivery is difficult because therapeutic compounds need to survive numerous transport barriers and binding targets throughout the body. Nanoscale protein-based polymers are increasingly used for drug and vaccine delivery to cross these biological barriers and through blood circulation to their molecular site of action. Protein-based polymers compared to synthetic polymers have the advantages of good biocompatibility, biodegradability, environmental sustainability, cost effectiveness and availability. This review addresses the sources of protein-based polymers, compares the similarity and differences, and highlights characteristic properties and functionality of these protein materials for sustained and controlled drug release. Targeted drug delivery using highly functional multicomponent protein composites to guide active drugs to the site of interest will also be discussed. A systematical elucidation of drug-delivery efficiency in the case of molecular weight, particle size, shape, morphology, and porosity of materials will then be demonstrated to achieve increased drug absorption. Finally, several important biomedical applications of protein-based materials with drug-delivery function—including bone healing, antibiotic release, wound healing, and corneal regeneration, as well as diabetes, neuroinflammation and cancer treatments—are summarized at the end of this review. PMID:28772877

  17. Protein-Based Drug-Delivery Materials

    Directory of Open Access Journals (Sweden)

    Dave Jao

    2017-05-01

    Full Text Available There is a pressing need for long-term, controlled drug release for sustained treatment of chronic or persistent medical conditions and diseases. Guided drug delivery is difficult because therapeutic compounds need to survive numerous transport barriers and binding targets throughout the body. Nanoscale protein-based polymers are increasingly used for drug and vaccine delivery to cross these biological barriers and through blood circulation to their molecular site of action. Protein-based polymers compared to synthetic polymers have the advantages of good biocompatibility, biodegradability, environmental sustainability, cost effectiveness and availability. This review addresses the sources of protein-based polymers, compares the similarity and differences, and highlights characteristic properties and functionality of these protein materials for sustained and controlled drug release. Targeted drug delivery using highly functional multicomponent protein composites to guide active drugs to the site of interest will also be discussed. A systematical elucidation of drug-delivery efficiency in the case of molecular weight, particle size, shape, morphology, and porosity of materials will then be demonstrated to achieve increased drug absorption. Finally, several important biomedical applications of protein-based materials with drug-delivery function—including bone healing, antibiotic release, wound healing, and corneal regeneration, as well as diabetes, neuroinflammation and cancer treatments—are summarized at the end of this review.

  18. Satellite Contamination and Materials Outgassing Knowledge base

    Science.gov (United States)

    Minor, Jody L.; Kauffman, William J. (Technical Monitor)

    2001-01-01

    Satellite contamination continues to be a design problem that engineers must take into account when developing new satellites. To help with this issue, NASA's Space Environments and Effects (SEE) Program funded the development of the Satellite Contamination and Materials Outgassing Knowledge base. This engineering tool brings together in one location information about the outgassing properties of aerospace materials based upon ground-testing data, the effects of outgassing that has been observed during flight and measurements of the contamination environment by on-orbit instruments. The knowledge base contains information using the ASTM Standard E- 1559 and also consolidates data from missions using quartz-crystal microbalances (QCM's). The data contained in the knowledge base was shared with NASA by government agencies and industry in the US and international space agencies as well. The term 'knowledgebase' was used because so much information and capability was brought together in one comprehensive engineering design tool. It is the SEE Program's intent to continually add additional material contamination data as it becomes available - creating a dynamic tool whose value to the user is ever increasing. The SEE Program firmly believes that NASA, and ultimately the entire contamination user community, will greatly benefit from this new engineering tool and highly encourages the community to not only use the tool but add data to it as well.

  19. Comparison or organic and inorganic ion exchange materials for removal of cesium and strontium from Hanford waste

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G.N.; Carson, K.J.; DesChane, J.R.; Elovich, R.J. [Pacific Northwest National Lab., Richland, WA (United States)

    1997-10-01

    This work is part of an ESP-CP task to develop and evaluate high-capacity, selective, solid extractants for the uptake of cesium, strontium, and technetium (Cs, Sr, and Tc) from nuclear wastes. Pacific Northwest National Laboratory (PNNL) staff, in collaboration with researchers from industry, academia, and national laboratories are investigating these and other novel and commercial ion exchangers for use in nuclear waste remediation of groundwater, HLW, and LLW. Since FY 1995, experimental work at PNNL has focused on small-scale batch distribution (K{sub d}) testing of numerous solid sorbents with actual and simulated Hanford wastes, chemical and radiolytic stability of various organic ion exchanger resins, bench-scale column ion exchange testing in actual and simulated Complexant Concentrate (CC) and Neutralized Current Acid Waste (NCAW), and Tc and Sr removal from groundwater and LLW. In addition, PNNL has continued to support various site demonstrations at the Idaho National Engineering Laboratory, Savannah River Site, West Valley Nuclear Services, Hanford N-Springs, and Hanford N-Basin using technologies developed by their industrial partners. This summary will focus on batch distribution results from the actual waste tests. The data collected in these development and testing tasks provide a rational basis for the selection and direct comparison of various ion exchange materials in simulated and actual HLW, LLW, and groundwater. In addition, prediction of large-scale column loading performance for the materials tested is possible using smaller volumes of actual waste solution. The method maximizes information while minimizing experimental expense, time, and laboratory and process wastes.

  20. Microalgae dewatering based on forward osmosis employing proton exchange membrane.

    Science.gov (United States)

    Son, Jieun; Sung, Mina; Ryu, Hoyoung; Oh, You-Kwan; Han, Jong-In

    2017-11-01

    In this study, electrically-facilitated forward osmosis (FO) employing proton exchange membrane (PEM) was established for the purpose of microalgae dewatering. An increase in water flux was observed when an external voltage was applied to the FO equipped with the PEM; as expected, the trend became more dramatic with both concentration of draw solution and applied voltage raised. With this FO used for microalgae dewatering, 247% of increase in flux and 86% in final biomass concentration were observed. In addition to the effect on flux improvement, the electrically-facilitated FO exhibited the ability to remove chlorophyll from the dewatered biomass, down to 0.021±0015mg/g cell. All these suggest that the newly suggested electrically-facilitated FO, one particularly employed PEM, can indeed offer a workable way of dewatering of microalgae; it appeared to be so because it can also remove the ever-problematic chlorophyll from extracted lipids in a simultaneous fashion. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. New inorganic (an)ion exchangers based on Mg–Al hydrous oxides: (Alkoxide-free) sol–gel synthesis and characterisation

    NARCIS (Netherlands)

    Chubar, N.

    2011-01-01

    New inorganic ion exchangers based on double Mg–Al hydrous oxides were generated via the new non-traditional sol–gel synthesis method which avoids using metal alkoxides as raw materials. Surface chemical and adsorptive properties of the final products were controlled by several ways of hydrogels and

  2. Factors affecting the exchange of genetic material between Nordic and US Holstein populatons

    DEFF Research Database (Denmark)

    Buch, L H; Sørensen, A C; Lassen, J

    2009-01-01

    be explained by differences in economic values, trait definitions, national genetic evaluation procedures, and genotype x environment interactions. The objective of this study was to test whether uniform definitions of the female fertility traits would increase the exchange of genes across populations......, and to quantify the effect on genetic gain. A second objective was to test whether a more similar relative weighting of the index traits across populations would increase the exchange of genes across populations, and to quantify the effect on genetic gain. This was done in a stochastic simulation study...... of the Nordic and US Holstein populations. Uniform definitions of the female fertility traits did not increase total genetic gain in the Nordic Holstein population. The standardization did not seem to affect selection across populations either. However, the results were sensitive to the assumptions made...

  3. Diatom-Based Material Production Demonstration

    Science.gov (United States)

    2016-03-14

    The vast majority of these researchers have little or no experience in diatom cultivation or cell wall purification. Ready availability of a wider...there is a little bit of a ‘chicken and egg’ phenomena in that limited availability of diatom cell walls constrains the research on GAI Final...based on application of these unique materials. Such a project would not only advance current research on diatom cell wall applications, but could be

  4. Nanocellulose-Based Materials for Water Purification

    OpenAIRE

    Hugo Voisin; Lennart Bergström; Peng Liu; Mathew, Aji P.

    2017-01-01

    Nanocellulose is a renewable material that combines a high surface area with high strength, chemical inertness, and versatile surface chemistry. In this review, we will briefly describe how nanocellulose is produced, and present?in particular, how nanocellulose and its surface modified versions affects the adsorption behavior of important water pollutants, e.g., heavy metal species, dyes, microbes, and organic molecules. The processing of nanocellulose-based membranes and filters for water pu...

  5. Development and Exchange of Instructional Resources in Water Quality Control Programs, II: Instructional Materials Available.

    Science.gov (United States)

    Austin, John H.

    This document is one in a series of reports which reviews instructional materials and equipment for water and wastewater treatment plant personnel. Approximately 900 items are listed in this document along with guidelines for the production of instructional materials. Information is provided regarding the source, type of material, intended…

  6. Bifunctional thermoelectric tube made of tilted multilayer material as an alternative to standard heat exchangers.

    Science.gov (United States)

    Takahashi, Kouhei; Kanno, Tsutomu; Sakai, Akihiro; Tamaki, Hiromasa; Kusada, Hideo; Yamada, Yuka

    2013-01-01

    Enormously large amount of heat produced by human activities is now mostly wasted into the environment without use. To realize a sustainable society, it is important to develop practical solutions for waste heat recovery. Here, we demonstrate that a tubular thermoelectric device made of tilted multilayer of Bi(0.5)Sb(1.5)Te3/Ni provides a promising solution. The Bi(0.5)Sb(1.5)Te3/Ni tube allows tightly sealed fluid flow inside itself, and operates in analogy with the standard shell and tube heat exchanger. We show that it achieves perfect balance between efficient heat exchange and high-power generation with a heat transfer coefficient of 4.0 kW/m(2)K and a volume power density of 10 kW/m(3) using low-grade heat sources below 100°C. The Bi(0.5)Sb(1.5)Te3/Ni tube thus serves as a power generator and a heat exchanger within a single unit, which is advantageous for developing new cogeneration systems in factories, vessels, and automobiles where cooling of excess heat is routinely carried out.

  7. Composite Materials and Films Based on Melanins, Polydopamine, and Other Catecholamine-Based Materials

    Directory of Open Access Journals (Sweden)

    Vincent Ball

    2017-07-01

    Full Text Available Polydopamine (PDA is related to eumelanins in its composition and structure. These pigments allow the design, inspired by natural materials, of composite nanoparticles and films for applications in the field of energy conversion and the design of biomaterials. This short review summarizes the main advances in the design of PDA-based composites with inorganic and organic materials.

  8. Forensic Identification Based on Tooth Material

    Directory of Open Access Journals (Sweden)

    Elza Ibrahim Auerkari

    2015-10-01

    Full Text Available Human teeth are the most robust and stable parts of the body, providing biological clue material for forensic purposes even when most of the oter means of identifcation have been seriously affected by adverse environmental conditions. In particular blood grouping, isozymes, serum proteins and DNA polymorhphisms can be detected from teeth that protect these identification markers in addition to the traditional dental records. While in general the value of traditional dental records in the forensic work is decreasing eg due to mproved dental care, the newer means of identification from tooth material provide considerable promise for effective identification in difficult cases.The DNA analysis from tooth material has been shown to ba a viable route in forensic analysis, when other material for such an analysis is unusable. However in most cases useful biologic material other than teeth is abailable, and then DNA analysis can be made from other tissue with less effort than by using teeth. Also, in cases with lacking other tissue, blood grouping, isozymes and serum proteins may provide cheaper inherited combinations of blood grouping, isozymes and serum proteins can be treated similary to polymorphic DNA loci as independent markers, their identification can be managed if the false positives and negatives in analysis can be minimmised, and the corresponding frequencies of occurrence are known.It was the purpose of the present work to review the methods of forensic identification from tooth material, based on analysis of blood grouping, isozymes and serum proteins. It appears that such a combined analysis provides a robust method for forensic purposes. Nevertheless, for efficient identification it is recommended that as many (multiple forensic methods as possible are combined, so that faster and cheaper methods such as imminent medical forensics are used first, and more thorough analysis is used to support and complement these methods.

  9. Effects of gas exchange on acid-base balance.

    Science.gov (United States)

    Lindinger, Michael I; Heigenhauser, George J F

    2012-07-01

    This paper describes the interactions between ventilation and acid-base balance under a variety of conditions including rest, exercise, altitude, pregnancy, and various muscle, respiratory, cardiac, and renal pathologies. We introduce the physicochemical approach to assessing acid-base status and demonstrate how this approach can be used to quantify the origins of acid-base disorders using examples from the literature. The relationships between chemoreceptor and metaboreceptor control of ventilation and acid-base balance summarized here for adults, youth, and in various pathological conditions. There is a dynamic interplay between disturbances in acid-base balance, that is, exercise, that affect ventilation as well as imposed or pathological disturbances of ventilation that affect acid-base balance. Interactions between ventilation and acid-base balance are highlighted for moderate- to high-intensity exercise, altitude, induced acidosis and alkalosis, pregnancy, obesity, and some pathological conditions. In many situations, complete acid-base data are lacking, indicating a need for further research aimed at elucidating mechanistic bases for relationships between alterations in acid-base state and the ventilatory responses. 2012 American Physiological Society. Compr Physiol 2:2037-2061, 2012.

  10. [Determination of soil exchangeable base cations by using atomic absorption spectrophotometer and extraction with ammonium acetate].

    Science.gov (United States)

    Zhang, Yu-ge; Xiao, Min; Dong, Yi-hua; Jiang, Yong

    2012-08-01

    A method to determine soil exchangeable calcium (Ca), magnesium (Mg), potassium (K), and sodium (Na) by using atomic absorption spectrophotometer (AAS) and extraction with ammonium acetate was developed. Results showed that the accuracy of exchangeable base cation data with AAS method fits well with the national standard referential soil data. The relative errors for parallel samples of exchangeable Ca and Mg with 66 pair samples ranged from 0.02%-3.14% and 0.06%-4.06%, and averaged to be 1.22% and 1.25%, respectively. The relative errors for exchangeable K and Na with AAS and flame photometer (FP) ranged from 0.06%-8.39% and 0.06-1.54, and averaged to be 3.72% and 0.56%, respectively. A case study showed that the determination method for exchangeable base cations by using AAS was proven to be reliable and trustable, which could reflect the real situation of soil cation exchange properties in farmlands.

  11. Relation between electrical percolation and rate constant for exchange of material between droplets in water in oil microemulsions

    Energy Technology Data Exchange (ETDEWEB)

    Jada, A.; Lang, J.; Zana, R. (Institut Charles Sadron, Strasbourg (France))

    1989-01-12

    The rate constant k{sub e} associated with the exchange of material upon collisions between droplets in ternary water in oil microemulsions stabilized by ionic surfactants has been determined by a time-resolved fluorescence method. The electrical conductivity of the same systems has been investigated. It appears that percolative conduction occurs only in systems where k{sub e} is larger than (1-2) {times} 10{sup 9} M{sup {minus}1} s{sup {minus}1}. This result supports the hypothesis that above percolation threshold the conductivity is mainly due to the motion of counterions through water channels or fusion between droplets in droplet clusters.

  12. Anion-exchange resin-based desulfurization process. Quarterly technical progress report, October 1, 1991--December 31, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Sheth, A.C.; Strevel, S.D.

    1991-12-31

    The University of Tennessee Space Institute (UTSI) has a Department of Energy grant to further develop the Institute`s anion-exchange resin-based flue gas, desulfurization concept. The developmental program proposed includes screening of commercially available resins to select three candidate resins for further study. These three resins will undergo a series of experiments designed to test the resins` performance under different process conditions (including the use of spent MHD seed material). The best of these resins will be used in optimizing the regeneration step and in testing the effects of performance enhancers. The process schematic developed from the results will be used to estimate the related economics.

  13. Academic Entrepreneurship and Exchange of Scientific Resources: Material Transfer in Life and Materials Sciences in Japanese Universities

    Science.gov (United States)

    Shibayama, Sotaro; Walsh, John P.; Baba, Yasunori

    2012-01-01

    This study uses a sample of Japanese university scientists in life and materials sciences to examine how academic entrepreneurship has affected the norms and behaviors of academic scientists regarding sharing scientific resources. Results indicate that high levels of academic entrepreneurship in a scientific field are associated with less reliance…

  14. Polydopamine Based Colloidal Materials: Synthesis and Applications.

    Science.gov (United States)

    Deng, Ziwei; Shang, Bin; Peng, Bo

    2017-11-10

    Polydopamine is a synthetic analogue of natural melanin (eumelanin) produced from oxidative polymerization of dopamine. Owing to its strong adhesion ability, versatile chemical reactivity, biocompatibility and biodegradation, polydopamine is commonly applied as a versatile linker to synthesize colloidal materials with diverse structures, unique physicochemical properties and tunable functions, which allow for a broad scope of applications including biomedicine, sensing, catalysis, environment and energy. In this personal account, we discuss first about the different synthetic approaches of polydopamine, as well as its polymerization mechanism, and then with a comprehensive overview of recent progress in the synthesis and applications of polydopamine-based colloidal materials. Finally, we summarize this personal account with future perspectives. © 2017 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Cucurbituril-based supramolecular engineered nanostructured materials.

    Science.gov (United States)

    Gürbüz, Sinem; Idris, Muazzam; Tuncel, Dönüs

    2015-01-14

    Cucurbituril (CB) is a unique macrocycle with a rigid symmetrical structure, which is composed of two identical hydrophilic portals decorated with partially negatively charged carbonyl groups and a hydrophobic cavity. A number of different nanostructured materials, including nanoparticles, nanocomposites, vesicles and rods, have been prepared by taking advantage of the varying cavity size of the CB homologues, their ability to accommodate more than one guest in their cavities, their rigid symmetrical structures, as well as the water solubility of CB7. These nanostructures could find a wide range of potential applications in the areas of self-healing materials, nanomedicine, plasmonics, and nanocatalysis. Here, we review the recent progresses in the synthesis, properties and application of CB-based supramolecular engineered nanostructures, which are either constructed through CB-assisted self-assembly or from post-functionalized-CB homologues.

  16. Model-based fault detection for proton exchange membrane fuel cell ...

    African Journals Online (AJOL)

    In this paper, an intelligent model-based fault detection (FD) is developed for proton exchange membrane fuel cell (PEMFC) dynamic systems using an independent radial basis function (RBF) networks. The novelty is that this RBF networks is used to model the PEMFC dynamic systems and residuals are generated based ...

  17. Study of wheat protein based materials

    Science.gov (United States)

    Ye, Peng

    Wheat gluten is a naturally occurring protein polymer. It is produced in abundance by the agricultural industry, is biodegradable and very inexpensive (less than $0.50/lb). It has unique viscoelastic properties, which makes it a promising alternative to synthetic plastics. The unplasticized wheat gluten is, however, brittle. Plasticizers such as glycerol are commonly used to give flexibility to the articles made of wheat gluten but with the penalty of greatly reduced stiffness. Former work showed that the brittleness of wheat gluten can also be improved by modifying it with a tri-thiol additive with no penalty of reduced stiffness. However, the cost of the customer designed tri-thiol additive was very high and it was unlikely to make a cost effective material from such an expensive additive. Here we designed a new, inexpensive thiol additive called SHPVA. It was synthesized from polyvinyl alcohol (PVA) through a simple esterification reaction. The mechanical data of the molded wheat gluten/SHPVA material indicated that wheat gluten was toughened by SHPVA. As a control, the wheat gluten/PVA material showed no improvement compared with wheat gluten itself. Several techniques have been used to characterize this novel protein/polymer blend. Differential scanning calorimetric (DSC) study showed two phases in both wheat gluten/PVA and wheat gluten/SHPVA material. However, scanning electron microscope (SEM) pictures indicated that PVA was macroscopically separated from wheat gluten, while wheat gluten/SHPVA had a homogeneous look. The phase image from the atomic force microscope (AFM) gave interesting contrast based on the difference in the mechanical properties of these two phases. The biodegradation behavior of these protein/polymer blends was examined in soil. SHPVA was not degraded in the time period of the experiment. Wheat gluten/SHPVA degraded slower than wheat gluten. We also developed some other interesting material systems based on wheat gluten, including the

  18. Inorganic ion exchangers based on manganese and potassium for recovery and removal of pollutant metals of aqueous effluents; Trocadores ionicos inorganicos a base de manganes e potassio para recuperacao e remocao de metais poluentes de efluentes aquosos

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Jacinete Lima dos

    2001-07-01

    This work presents a study on the synthesis, characterization and ion exchange properties of inorganic ion exchangers based on manganese and potassium. The ion exchangers were synthesized by calcination of the mixture of manganese(II) oxalate and potassium oxalate and were characterized by granulometer distribution analysis, X-ray powder diffraction, infrared spectroscopy and scanning electron microscopic. From the data obtained in characterization it was observed that exist two distinguished groups of these materials. The first group belong to ion exchangers with up to 30% w/w potassium and the second group formed by the ion exchangers with more than 30% w / w of content of potassium in their compositions. The studies of adsorption of these materials showed that the adsorption of Cd{sup 2+} is a function of the following parameters as pH, concentration of Cd{sup 2+}, time of contact between the ion exchangers the concentration of the Cd{sup 2+} solution and the interference of other ions like Ni{sup 2+}. The great pH of adsorption for these materials occur in pH 9, the study of the influence of the cadmium concentration in the adsorption showed that for a group of exchangers the adsorption decreases with the increase of cadmium concentration and for the other group the adsorption increases with the increase of cadmium concentration. The kinetics of adsorption occur in a contact time between the ion exchangers and the Cd{sup 2+} solutions relatively short, at about 15 minutes is necessary to establish the equilibrium. The presence of Ni{sup 2+} as interfering ion decreases the adsorption of cadmium of 99,7% to 65%. These inorganic ion exchangers showed be good exchangers for Cd{sup 2+}. (author)

  19. Exchange bias in zinc ferrite-FeNiMoB based metallic glass composite thin films

    Energy Technology Data Exchange (ETDEWEB)

    R, Lisha; P, Geetha; B, Aravind P.; Anantharaman, M. R., E-mail: mraiyer@yahoo.com [Cochin University of Science and Technology, Cochin-682022 (India); T, Hysen [Christian College, Chengannur, Kerala-689121 (India); Ojha, S.; Avasthi, D. K. [Inter University Accelerator Centre, Vasant Kunj, New Delhi-110067 (India); Ramanujan, R. V. [School of Materials Science and Engineering, Nanyang Technological University (Singapore)

    2015-06-24

    The Exchange bias phenomenon and methods to manipulate the bias field in a controlled manner are thrust areas in magnetism due to its sophisticated theoretical concepts as well as advanced technological utility in the field of spintronics. The Exchange bias effect is observed as a result of ferromagnetic-antiferromagnetic (FM-AFM) exchange interaction, usually observed as a loop shift on field cooling below the Neel temperature of AFM. In the present study, we have chosen zinc ferrite which is a well known antiferromagnet, and FeNiMoB based metallic glass as the ferromagnet. The films were prepared by RF sputtering technique. The thickness and composition was obtained by RBS. The magnetic studies using SQUID VSM indicate exchange bias effect in the system. The effect of thermal annealing on exchange bias effect was studied. The observed exchange bias in the zinc ferrite-FeNiMoB system is not due to FM-AFM coupling but due to spin glass-ferromagnetic interaction.

  20. Synthesis of Highly Sulfonated Poly(arylene ether Containing Multiphenyl for Proton Exchange Membrane Materials

    Directory of Open Access Journals (Sweden)

    Yi-Chiang Huang

    2016-01-01

    Full Text Available A series of sterically hindered, sulfonated, poly(arylene ether polymers were synthesized by nucleophilic polycondensation reaction using 4,4′′′′-difluoro-3,3′′′′-bistrifluoromethyl-2′′,3′′,5′′,6′′-tetraphenyl-[1,1′;4′,1′′;4′′,1′′′;4′′′,1′′′′]-pentaphenyl and 4,4′-biphenol and were prepared through postpolymerization sulfonation. The chemical structures were confirmed by 1H NMR. Subsequent to sulfonation, solvent-casting membranes were provided ion exchange capacity (IEC values ranging from 0.39 to 2.90 mmol/g. Proton conductivities of membranes ranged from 143 to 228 mS/cm at 80°C under fully humidified conditions which were higher than that of Nafion 117. The membrane also exhibited considerably dimension stability, oxidative stability, and hydrolytic stability. The microphase structure was investigated by transmission electron microscopy (TEM and the ionic aggregation of sulfonic acid groups exhibited spherical ionic clusters with well-developed phase separated morphology. The results indicated that the membranes are promising candidates for application as proton exchange membranes. This investigation demonstrates introducing multiphenylated moieties to create a high free volume polymer that provides dimensionally stable and high proton conductivity membranes.

  1. Concurrent studies of enhanced heat transfer and materials for ocean thermal exchangers. Progress report

    Energy Technology Data Exchange (ETDEWEB)

    Bonewitz, R.A.

    1976-10-29

    Aluminum alloys 1100, 3003, 5052, and 6063 were examined for their compatibility with the proposed working fluids for Ocean Thermal Energy Conversion (OTEC), anhydrous ammonia, Freon 22 and propane, and mixtures of these with sea water. Such mixtures would occur if leaks develop in evaporator or condenser heat exchangers. These aluminum alloys are compatible with the anhydrous working fluids. In ammonia-sea water solutions only limited general corrosion is found in 0 to 30 percent ammonia, no corrosion in 30 to 90 percent ammonia, and ''self limiting'' pits in 90 to 100 percent ammonia so rapid deterioration of the exchangers would not occur. No corrosion was observed in sea water saturated with Freon 22 or propane. No differences in alloy performance were evident in any of these tests so selection can be made on the basis of compatibility with sea water. A review of the available literature indicates that 5052 shows the best performance in surface sea water followed by 1100, 3003 and then 6063 alloy. In deep sea water only 5052 and 1100 alloys appear suitable although more data is required. In both surface and deep sea waters, alcladding offers the best protection against tube perforation; few instances of penetration into the core alloy have been observed for the alclad alloys examined in this study.

  2. Planning Education: Exchanging Approaches to Teaching Practice-Based Skills

    Science.gov (United States)

    Ritchie, Heather; Sheppard, Adam; Croft, Nick; Peel, Deborah

    2017-01-01

    Planning curricula have continually evolved to meet changing societal needs, technological change and employer expectations. The professional accrediting body in the United Kingdom, the Royal Town Planning Institute, stipulates the core planning skills required, differentiating between formal classroom-based learning and professional competencies,…

  3. Negative Dielectric Constant Material Based on Ion Conducting Materials

    Science.gov (United States)

    Gordon, Keith L. (Inventor); Kang, Jin Ho (Inventor); Park, Cheol (Inventor); Lillehei, Peter T. (Inventor); Harrison, Joycelyn S. (Inventor)

    2017-01-01

    Metamaterials or artificial negative index materials (NIMs) have generated great attention due to their unique and exotic electromagnetic properties. One exemplary negative dielectric constant material, which is an essential key for creating the NIMs, was developed by doping ions into a polymer, a protonated poly (benzimidazole) (PBI). The doped PBI showed a negative dielectric constant at megahertz (MHz) frequencies due to its reduced plasma frequency and an induction effect. The magnitude of the negative dielectric constant and the resonance frequency were tunable by doping concentration. The highly doped PBI showed larger absolute magnitude of negative dielectric constant at just above its resonance frequency than the less doped PBI.

  4. Community-based knowledge transfer and exchange: Helping community-based organizations link research to action

    Directory of Open Access Journals (Sweden)

    Lavis John N

    2010-04-01

    Full Text Available Abstract Background Community-based organizations (CBOs are important stakeholders in health systems and are increasingly called upon to use research evidence to inform their advocacy, program planning, and service delivery efforts. CBOs increasingly turn to community-based research (CBR given its participatory focus and emphasis on linking research to action. In order to further facilitate the use of research evidence by CBOs, we have developed a strategy for community-based knowledge transfer and exchange (KTE that helps CBOs more effectively link research evidence to action. We developed the strategy by: outlining the primary characteristics of CBOs and why they are important stakeholders in health systems; describing the concepts and methods for CBR and for KTE; comparing the efforts of CBR to link research evidence to action to those discussed in the KTE literature; and using the comparison to develop a framework for community-based KTE that builds on both the strengths of CBR and existing KTE frameworks. Discussion We find that CBR is particularly effective at fostering a climate for using research evidence and producing research evidence relevant to CBOs through community participation. However, CBOs are not always as engaged in activities to link research evidence to action on a larger scale or to evaluate these efforts. Therefore, our strategy for community-based KTE focuses on: an expanded model of 'linkage and exchange' (i.e., producers and users of researchers engaging in a process of asking and answering questions together; a greater emphasis on both producing and disseminating systematic reviews that address topics of interest to CBOs; developing a large-scale evidence service consisting of both 'push' efforts and efforts to facilitate 'pull' that highlight actionable messages from community relevant systematic reviews in a user-friendly way; and rigorous evaluations of efforts for linking research evidence to action. Summary

  5. Nanocellulose-Based Materials for Water Purification.

    Science.gov (United States)

    Voisin, Hugo; Bergström, Lennart; Liu, Peng; Mathew, Aji P

    2017-03-05

    Nanocellulose is a renewable material that combines a high surface area with high strength, chemical inertness, and versatile surface chemistry. In this review, we will briefly describe how nanocellulose is produced, and present-in particular, how nanocellulose and its surface modified versions affects the adsorption behavior of important water pollutants, e.g., heavy metal species, dyes, microbes, and organic molecules. The processing of nanocellulose-based membranes and filters for water purification will be described in detail, and the uptake capacity, selectivity, and removal efficiency will also be discussed. The processing and performance of nanocellulose-based membranes, which combine a high removal efficiency with anti-fouling properties, will be highlighted.

  6. Nanocellulose-Based Materials for Water Purification

    Directory of Open Access Journals (Sweden)

    Hugo Voisin

    2017-03-01

    Full Text Available Nanocellulose is a renewable material that combines a high surface area with high strength, chemical inertness, and versatile surface chemistry. In this review, we will briefly describe how nanocellulose is produced, and present—in particular, how nanocellulose and its surface modified versions affects the adsorption behavior of important water pollutants, e.g., heavy metal species, dyes, microbes, and organic molecules. The processing of nanocellulose-based membranes and filters for water purification will be described in detail, and the uptake capacity, selectivity, and removal efficiency will also be discussed. The processing and performance of nanocellulose-based membranes, which combine a high removal efficiency with anti-fouling properties, will be highlighted.

  7. Electrocatalysts and their Supporting Materials for Proton Exchange Membrane Fuel Cells: Activity and Durability Studies

    DEFF Research Database (Denmark)

    Permyakova, Anastasia Aleksandrovna

    This thesis describes investigations conducted exploring the activity, stability and durability of supported nano-particulate, bulk and thin film electrocatalysts used in proton exchange membrane fuel cells (PEMFCs). The effects of different factors and conditions on the reactions involved...... in oxygen reduction, carbon monoxide and methanol electro-oxidation reactions were explored. Employed catalysts were characterized electrochemically and physiochemically using techniques such as: cyclic voltammetry, rotating disk electrode technique, SEM, TEM, EDS, XPS, TGA/DTA, Raman, XRD, FTIR-IR among...... other methods. The thesis begins with an introduction in Chapter 1 providing an overview of fuel cells, their associated reaction mechanisms, catalysts and catalysts supports. Chapter 2 presents the theoretical background to the study including equipment and the techniques used to analyse the catalysts...

  8. Spintronic materials and devices based on antiferromagnetic metals

    Directory of Open Access Journals (Sweden)

    Y.Y. Wang

    2017-04-01

    Full Text Available In this paper, we review our recent experimental developments on antiferromagnet (AFM spintronics mainly comprising Mn-based noncollinear AFM metals. IrMn-based tunnel junctions and Hall devices have been investigated to explore the manipulation of AFM moments by magnetic fields, ferromagnetic materials and electric fields. Room-temperature tunneling anisotropic magnetoresistance based on IrMn as well as FeMn has been successfully achieved, and electrical control of the AFM exchange spring is realized by adopting ionic liquid. In addition, promising spin-orbit effects in AFM as well as spin transfer via AFM spin waves reported by different groups have also been reviewed, indicating that the AFM can serve as an efficient spin current source. To explore the crucial role of AFM acting as efficient generators, transmitters, and detectors of spin currents is an emerging topic in the field of magnetism today. AFM metals are now ready to join the rapidly developing fields of basic and applied spintronics, enriching this area of solid-state physics and microelectronics.

  9. Oxygen reduction and methanol oxidation behaviour of SiC based Pt nanocatalysts for proton exchange membrane fuel cells

    DEFF Research Database (Denmark)

    Dhiman, Rajnish; Stamatin, Serban Nicolae; Andersen, Shuang Ma

    2013-01-01

    Research with proton exchange membrane fuel cells has demonstrated their important potential as providers of clean energy. The commercialization of this type of fuel cell needs a breakthrough in electrocatalyst technology to reduce the relatively large amount of noble metal platinum used...... with the present carbon based substrates. We have recently examined suitably sized silicon carbide (SiC) particles as catalyst supports for fuel cells based on the stable chemical and mechanical properties of this material. In the present study, we have continued our work with studies of the oxygen reduction...... and methanol oxidation reactions of SiC supported catalysts and measured them against commercially available carbon based catalysts. The deconvolution of the hydrogen desorption signals in CV cycles shows a higher contribution of Pt (110) & Pt (111) peaks compared to Pt (100) for SiC based supports than...

  10. Proton exchange between oxymethyl radical and acids and bases: semiempirical quantum-chemical study

    Directory of Open Access Journals (Sweden)

    Irina Pustolaikina

    2016-12-01

    Full Text Available The reactions with proton participation are widely represented in the analytical, technological and biological chemistry. Quantum-chemical study of the exchange processes in hydrogen bonding complexes will allow us to achieve progress in the understanding of the elementary act mechanism of proton transfer in hydrogen bonding chain as well as the essence of the acid-base interactions. Oxymethyl radical •CH2ОН is small in size and comfortable as a model particle that well transmits protolytic properties of paramagnetic acids having more complex structure. Quantum-chemical modeling of proton exchange reaction oxymethyl radical ∙CH2OH and its diamagnetic analog CH3OH with amines, carboxylic acids and water was carried out using UAM1 method with the help of Gaussian-2009 program. QST2 method was used for the search of transition state, IRC procedure was applied for the calculation of descents along the reaction coordinate. The difference in the structure of transition states of ∙CH2OH/ CH3OH with bases and acids has been shown. It has been confirmed that in the case of bases, consecutive proton exchange mechanism was fixed, and in the case of complexes with carboxylic acids parallel proton exchange mechanism was fixed. The similarity in the reaction behavior of paramagnetic and diamagnetic systems in the proton exchange has been found. It was suggested that the mechanism of proton exchange reaction is determined by the structure of the hydrogen bonding cyclic complex, which is, in turn, depends from the nature of the acid-base interactions partners.

  11. Radiolytic preparation of ETFE and PFA based anion exchange membranes for alkaline fuel cell

    Science.gov (United States)

    Ko, Beom-Seok; Sohn, Joon-Yong; Nho, Young-Chang; Shin, Junhwa

    2011-11-01

    In this study, a versatile monomer, vinylbenzyl chloride (VBC) was radiolytically grafted onto a partially fluorinated ETFE and perfluorinated polymer PFA films. The VBC grafted films were treated with trimethylamine to prepare the alkaline anion exchange membranes (AAEMs). No significant differences in the ion exchange capacities and water uptakes were observed between the ETFE and PFA based AAEMs with similar degree of grafting (DOG). However, the distribution patterns of the graft chains over the cross-section of the ETFE and PFA based AAEMs were found to be quite different; the even distribution was observed from the ETFE based AAEMs while the uneven distribution was observed from the PFA based AAEMs. It was also found that the PFA based AAEMs have the higher ionic conductivity and chemical stability, compared to the ETFE based AAEMs.

  12. Comparing Acquisition of Exchange-Based and Signed Mands with Children with Autism

    Science.gov (United States)

    Barlow, Kathryn E.; Tiger, Jeffrey H.; Slocum, Sarah K.; Miller, Sarah J.

    2013-01-01

    Therapists and educators frequently teach alternative-communication systems, such as picture exchanges or manual signs, to individuals with developmental disabilities who present with expressive language deficits. Michael (1985) recommended a taxonomy for alternative communication systems that differentiated between selection-based systems in…

  13. An investigation into carbon nanostructured materials as catalyst support in proton exchange membrane fuel cells

    DEFF Research Database (Denmark)

    Veltzé, Sune

    black support materials for low platinum containing electrocatalyst. This is partly due to their high electronic conductivity. Partly due to their high surface area needed for the dispersion of nanoparticulate metal-clusters. In addition carbon nano-structures (CNF, SWCNT, MWCNT etc.) are more durable...

  14. Effect of airflow velocity on moisture exchange at surfaces of building materials

    DEFF Research Database (Denmark)

    Mortensen, Lone Hedegaard; Rode, Carsten; Peuhkuri, Ruut Hannele

    2006-01-01

    The moisture transfer between air and construction are affected of the boundary layer conditions close to the surface, which is influenced by the airflow patterns in the room. Therefore an investigation of the relation be-tween the surface resistance and the airflow velocity above a material samp...

  15. Electrokinetic salt removal from porous building materials using ion exchange membranes

    NARCIS (Netherlands)

    Kamran, K.; Van Soestbergen, M.; Pel, L.

    The removal of salt from porous building materials under the influence of an applied voltage gradient normally results in high pH gradients due to the formation of protons and hydroxyl ions at the electrodes. The formed acidic and alkaline regions not only lead to disintegration of the porous

  16. High Temperature Gas-to-Gas Heat Exchanger Based on a Solid Intermediate Medium

    Directory of Open Access Journals (Sweden)

    R. Amirante

    2014-04-01

    Full Text Available This paper proposes the design of an innovative high temperature gas-to-gas heat exchanger based on solid particles as intermediate medium, with application in medium and large scale externally fired combined power plants fed by alternative and dirty fuels, such as biomass and coal. An optimization procedure, performed by means of a genetic algorithm combined with computational fluid dynamics (CFD analysis, is employed for the design of the heat exchanger: the goal is the minimization of its size for an assigned heat exchanger efficiency. Two cases, corresponding to efficiencies equal to 80% and 90%, are considered. The scientific and technical difficulties for the realization of the heat exchanger are also faced up; in particular, this work focuses on the development both of a pressurization device, which is needed to move the solid particles within the heat exchanger, and of a pneumatic conveyor, which is required to deliver back the particles from the bottom to the top of the plant in order to realize a continuous operation mode. An analytical approach and a thorough experimental campaign are proposed to analyze the proposed systems and to evaluate the associated energy losses.

  17. Highly explosive nanosilicon-based composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Clement, D.; Diener, J.; Gross, E.; Kuenzner, N.; Kovalev, D. [Technical University of Munich, Physics Department, James-Franck-Str., 85747 Garching (Germany); Timoshenko, V.Yu. [Moscow State M.V. Lomonosov University, Physics Department, 119899 Moscow (Russian Federation)

    2005-06-01

    We present a highly explosive binary system based on porous silicon layers with their pores filled with solid oxidizers. The porous layers are produced by a standard electrochemical etching process and exhibit properties that are different from other energetic materials. Its production is completely compatible with the standard silicon technology and full bulk silicon wafers can be processed and therefore a large number of explosive elements can be produced simultaneously. The application-relevant parameters: the efficiency and the long-term stability of various porous silicon/oxidizer systems have been studied in details. Structural properties of porous silicon, its surface termination, the atomic ratio of silicon to oxygen and the chosen oxidizers were optimized to achieve the highest efficiency of the explosive reaction. This explosive system reveals various possible applications in different industrial fields, e.g. as a novel, very fast airbag igniter. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  18. Surface Functionalization of Graphene-based Materials

    Science.gov (United States)

    Mathkar, Akshay

    Graphene-based materials have generated tremendous interest in the past decade. Manipulating their characteristics using wet-chemistry methods holds distinctive value, as it provides a means towards scaling up, while not being limited by yield. The majority of this thesis focuses on the surface functionalization of graphene oxide (GO), which has drawn tremendous attention as a tunable precursor due to its readily chemically manipulable surface and richly functionalized basal plane. Firstly, a room-temperature based method is presented to reduce GO stepwise, with each organic moiety being removed sequentially. Characterization confirms the carbonyl group to be reduced first, while the tertiary alcohol is reduced last, as the optical gap decrease from 3.5 eV down to 1 eV. This provides greater control over GO, which is an inhomogeneous system, and is the first study to elucidate the order of removal of each functional group. In addition to organically manipulating GO, this thesis also reports a chemical methodology to inorganically functionalize GO and tune its wetting characteristics. A chemical method to covalently attach fluorine atoms in the form of tertiary alkyl fluorides is reported, and confirmed by MAS 13C NMR, as two forms of fluorinated graphene oxide (FGO) with varying C/F and C/O ratios are synthesized. Introducing C-F bonds decreases the overall surface free energy, which drastically reduces GO's wetting behavior, especially in its highly fluorinated form. Ease of solution processing leads to development of sprayable inks that are deposited on a range of porous and nonporous surfaces to impart amphiphobicity. This is the first report that tunes the wetting characteristics of GO. Lastly as a part of a collaboration with ConocoPhillips, another class of carbon nanomaterials - carbon nanotubes (CNTs), have been inorganically functionalized to repel 30 wt% MEA, a critical solvent in CO 2 recovery. In addition to improving the solution processability of CNTs

  19. The Use of ICT Platforms to Promote Knowledge Exchange in Project-Based Organisations

    Directory of Open Access Journals (Sweden)

    Priyono Anjar

    2016-12-01

    Full Text Available This study aims to investigate the use of information and communication technology (ICT to support knowledge exchange in project-based organisations. The primary ICT tool investigated in this research is WhatsApp, a messaging application that has been widely used since its introduction. An ethnographic case study method was utilised to analyse qualitative data collected from interviews and focus group discussions. Three projects in an Indonesian university with a duration ranging from 8 months to 2 years were examined as object of investigations. Broadly, the findings show that ICT tools are generally useful in supporting knowledge exchange, which ultimately positively affects project performance. The project teams relied on WhatsApp for the success of the projects. Although face-to-face meetings were rare, team communication was highly intensive, supported by WhatsApp. In addition, managers are encouraged to promote knowledge exchange between team members. Through knowledge exchange, there will be knowledge development, which facilitates the invention of new techniques and methods for promoting project success. The most prominent findings are presented using direct quotations to provide first hand insight from the field. At the end of the paper, recommendations regarding what project managers should do during and after the project has been completed are presented. The recommendations are classified based on the knowledge management life cycle, representing a structured method to manage knowledge in project-based organisations.

  20. [Yi lin cuo yao (Essentials of medical works) and its historical materials of medical exchanges between China and Korea].

    Science.gov (United States)

    Liang, Y

    2001-01-01

    Yi lin cuo yao, including 13 chapters and 128 categories, was written by Zheng Zhengxian and collated by Yang Lishou, both Korean imperial physicians in the 16 -- 17th centuries. With notation of a number of the Chinese and Korean medical books and materials in the first decade of the Li dynasty, this book is a comprehensive prescription work, very useful to clinical application. Especially with several points of the formulas from Zhong chao zhi wen fang (Sino -- Korean Prescriptions of Questioning) and zhong chao chuan xi fang (Sino -- Korean Prescriptions of Questioning) recorded in this book connected with Ren zhai zhi zhi fang lun (Renzhai's Comprehensive Prescriptions) in the Song dynasty. This book is an important record of the exchanges on medical ideas between China and Korea. However, it has nothing to do with Yi xue yi wen (Questions on Medicine) by Fu Maoguang, which records the questions and answers between Chinese and Korean officials.

  1. Key exchange using biometric identity based encryption for sharing encrypted data in cloud environment

    Science.gov (United States)

    Hassan, Waleed K.; Al-Assam, Hisham

    2017-05-01

    The main problem associated with using symmetric/ asymmetric keys is how to securely store and exchange the keys between the parties over open networks particularly in the open environment such as cloud computing. Public Key Infrastructure (PKI) have been providing a practical solution for session key exchange for loads of web services. The key limitation of PKI solution is not only the need for a trusted third partly (e.g. certificate authority) but also the absent link between data owner and the encryption keys. The latter is arguably more important where accessing data needs to be linked with identify of the owner. Currently available key exchange protocols depend on using trusted couriers or secure channels, which can be subject to man-in-the-middle attack and various other attacks. This paper proposes a new protocol for Key Exchange using Biometric Identity Based Encryption (KE-BIBE) that enables parties to securely exchange cryptographic keys even an adversary is monitoring the communication channel between the parties. The proposed protocol combines biometrics with IBE in order to provide a secure way to access symmetric keys based on the identity of the users in unsecure environment. In the KE-BIOBE protocol, the message is first encrypted by the data owner using a traditional symmetric key before migrating it to a cloud storage. The symmetric key is then encrypted using public biometrics of the users selected by data owner to decrypt the message based on Fuzzy Identity-Based Encryption. Only the selected users will be able to decrypt the message by providing a fresh sample of their biometric data. The paper argues that the proposed solution eliminates the needs for a key distribution centre in traditional cryptography. It will also give data owner the power of finegrained sharing of encrypted data by control who can access their data.

  2. Ion exchange uptake of ammonium in wastewater from a Sewage Treatment Plant by zeolitic materials from fly ash.

    Science.gov (United States)

    Juan, Roberto; Hernández, Susana; Andrés, José M; Ruiz, Carmen

    2009-01-30

    The potential value of zeolitic materials (ZM) obtained from a hazardous waste, such as coal fly ash, for the retention of NH(4)(+) present in liquid effluents from a Sewage Treatment Plant (STP) is studied. A wastewater sample was taken from an STP in Zaragoza (Spain) after conventional treatment at the Plant. The water was treated with different amounts of three ZM: NaP1 zeolite, K-F zeolite and K-Chabazite/K-Phillipsite zeolites all of them in powdered and granulated state. The wastewater was treated by two kinds of processes: continuous stirring batch experiments with powdered ZM, and fixed packed bed of granulated ZM in a column. The powdered materials reduced about 80% of NH(4)(+) from wastewater, even in the presence of Ca(2+), which competes with NH(4)(+) for the cation exchange sites in zeolites. Around 70% of NH(4)(+) reduction was achieved with granulated materials. In both cases, moderate ZM/wastewater ratios had to be used to achieve those results, with K-zeolites slightly less effective in NH(4)(+) retention.

  3. Cement-based materials with graphene nanophase

    Science.gov (United States)

    Dalla, P. T.; Tragazikis, I. K.; Exarchos, D. A.; Dassios, K.; Matikas, T. E.

    2017-04-01

    Cement matrix composites with a conductive nano-reinforcement phase, lead to the development of innovative products. A matrix with carbon based nano-inclusions (graphene, carbon nanotubes, carbon nanofibers, carbon black) obtains multi-functional properties like enhanced mechanical, electrical, elastic and thermal properties and, therefore, the advantage of self-sensing in case of an inner defect. This research aims to characterize the nano-modified cement mortars with different concentrations of graphene nanophase. The results will be compared with data obtained from nanomaterials containing multi-walled carbon nanotubes. Comprehensive characteristics of these cement-based nanocomposites have been determined using destructive and nondestructive laboratory techniques. Flexural and compressive strength were measured. During four point bending tests, acoustic emission monitoring allowed for realtime identification of the damage process in the material. The electrical surface resistivity of graphene-reinforced cement mortars was measured by applying a known DC voltage, and compared to the electrical resistivity of nano-modified mortars with carbon nanotubes.

  4. Transport and exchange of U-series nuclides between suspended material, dissolved load and colloids in rivers draining basaltic terrains

    Science.gov (United States)

    Pogge von Strandmann, Philip A. E.; Burton, Kevin W.; Porcelli, Don; James, Rachael H.; van Calsteren, Peter; Gislason, Sigurður R.

    2011-01-01

    This study presents uranium and thorium concentrations and activity ratios for all riverine phases (bedload, suspended load, dissolved load and colloids) from basaltic terrains in Iceland and the Azores. Small basaltic islands, such as these, are thought to account for ~ 25% of CO2 consumed by global silicate weathering, and for ~ 45% of the flux of suspended material to the oceans. These data indicate that [U] and [Th] in the dissolved and colloidal fractions are strongly controlled by pH, and to a much lesser extent by levels of dissolved organic carbon (which are low in these environments). At high pH, basalt glass dissolution is enhanced, and secondary mineral formation (e.g. Fe-oxyhydroxides and allophane) is suppressed, resulting in high dissolved [U], and low colloidal [U] and [Th], indicating a direct chemical weathering control on elemental abundances. When the dissolved (234U/238U) activity ratio is >~1.3 (i.e. when physical weathering, groundwater contribution or soil formation are high), there is little isotope exchange between dissolved and colloidal fractions. At lower activity ratios, the dissolved load and colloids have indistinguishable activity ratios, suggesting that when chemical weathering rates are high, secondary clay formation is also high, and colloids rapidly adsorb dissolved U. Many of the suspended sediment samples have (234U/238U) activity ratios of > 1, which suggests that uptake of U onto the suspended load is important. Identical (230Th/232Th) in suspended, dissolved and colloidal samples suggests that Th, like U, is exchanged or sorbed rapidly between all riverine phases. This particle-reactivity, combined with poorly constrained contributions from groundwater and hydrothermal water, and short-term variations in input to soils (volcanic and glacial), suggests that U-series nuclides in riverine material from such basaltic terrains are unlikely to reflect steady state erosion processes.

  5. Water vapor movement in freezing aggregate base materials.

    Science.gov (United States)

    2014-06-01

    The objectives of this research were to 1) measure the extent to which water vapor movement results in : water accumulation in freezing base materials; 2) evaluate the effect of soil stabilization on water vapor movement : in freezing base materials;...

  6. Surface characterization of graphene based materials

    Energy Technology Data Exchange (ETDEWEB)

    Pisarek, M., E-mail: mpisarek@ichf.edu.pl [Institute of Physical Chemistry, Polish Academy of Sciences, Kasprzaka 44/52, 01-224 Warsaw (Poland); Holdynski, M.; Krawczyk, M.; Nowakowski, R.; Roguska, A. [Institute of Physical Chemistry, Polish Academy of Sciences, Kasprzaka 44/52, 01-224 Warsaw (Poland); Malolepszy, A. [Faculty of Chemical and Process Engineering, Warsaw University of Technology, Warynskiego 1, 00-065 Warsaw (Poland); Stobinski, L. [Institute of Physical Chemistry, Polish Academy of Sciences, Kasprzaka 44/52, 01-224 Warsaw (Poland); Faculty of Chemical and Process Engineering, Warsaw University of Technology, Warynskiego 1, 00-065 Warsaw (Poland); Jablonski, A. [Institute of Physical Chemistry, Polish Academy of Sciences, Kasprzaka 44/52, 01-224 Warsaw (Poland)

    2016-12-01

    Highlights: • Two kind of samples: commercial graphene on Cu substrate and rGO flakes. • EPES applied to measure the IMFPs in graphene based materials. • Characterization by various techniques like: FE-SEM, AFM, XPS, AES and REELS. • EPES IMFPs for rGO deviated up to 14% from IMFPs calculated using the optical data. - Abstract: In the present study, two kind of samples were used: (i) a monolayer graphene film with a thickness of 0.345 nm deposited by the CVD method on Cu foil, (ii) graphene flakes obtained by modified Hummers method and followed by reduction of graphene oxide. The inelastic mean free path (IMFP), characterizing electron transport in graphene/Cu sample and reduced graphene oxide material, which determines the sampling depth of XPS and AES were evaluated from relative Elastic Peak Electron Spectroscopy (EPES) measurements with the Au standard in the energy range 0.5–2 keV. The measured IMFPs were compared with IMFPs resulting from experimental optical data published in the literature for the graphite sample. The EPES IMFP values at 0.5 and 1.5 keV was practically identical to that calculated from optical data for graphite (less than 4% deviation). For energies 1 and 2 keV, the EPES IMFPs for rGO were deviated up to 14% from IMFPs calculated using the optical data by Tanuma et al. [1]. Before EPES measurements all samples were characterized by various techniques like: FE-SEM, AFM, XPS, AES and REELS to visualize the surface morphology/topography and identify the chemical composition.

  7. Tribological properties of aluminium-based materials

    Science.gov (United States)

    Iglesias Victoria, Patricia

    In order to improve the tribological performance of the aluminium-steel contact, two research lines have been followed: (1) Use of the ordered fluids liquid crystals and ionic liquids as lubricant additives. (2) Tribological behaviour of new powder metallurgy aluminium materials processed by mechanical milling. A parafinic-naftenic base oil modified by a 1wt% of four additives has been used: Three liquid crystals with increasing polarity: 4,4' -dibutylazobenzene (LC1) wear was studied for each additive. While the ionic liquid gives low friction (wear (≤10-5 mm3m-1), the performance of the liquid crystalline additives depends on the conditions. LC3 shows a higher lubricating ability than the neutral LC1 and LC2 under high load, speed or temperature. Only the ionic liquid shows tribochemical interaction (by SEM and EDS) with the steel and aluminium surfaces, with an increment in the fluorine content inside the wear track. The second line was to study the influence of the process conditions on the dry and lubricated wear of new powder-metallurgy aluminium materials. MA Al-NH3 milled under NH3 atmosphere was compared with (MA Al-Air) processed in air and with Al-1 which has not been mechanically alloyed. Conditions for mild to severe wear transition have been established. Al-1 is always under a severe wear regime. MA Al-NH3 shows transition to severe wear at 150°C, showing a 60% reduction in wear rate with respect to MA Al-Air and a two order of magnitude reduction with respect to Al-1. The wear resistance of MA Al-NH3 is attributed to its high hardness, lower porosity, and fine microstructure with submicroscopic reinforcing phases such as aluminium carbide and nitride (by X-ray diffraction and TEM observations).

  8. Microfluidic Free-Flow Electrophoresis Based Solvent Exchanger for Continuously Operating Lab-on-Chip Applications.

    Science.gov (United States)

    Zitzmann, Franziska D; Jahnke, Heinz-Georg; Pfeiffer, Simon A; Frank, Ronny; Nitschke, Felix; Mauritz, Laura; Abel, Bernd; Belder, Detlev; Robitzki, Andrea A

    2017-12-19

    For miniaturization and integration of chemical synthesis and analytics on small length scales, the development of complex lab-on-chip (LOC) systems is in the focus of many current research projects. While application specific synthesis and analytic modules and LOC devices are widely described, the combination and integration of different modules is intensively investigated. Problems for in-line processes such as solvent incompatibilities, e.g., for a multistep synthesis or the combination of an organic drug synthesis with a cell-based biological activity testing system, require a solvent exchange between serialized modules. Here, we present a continuously operating microfluidic solvent exchanger based on the principle of free-flow electrophoresis for miscible organic/aqueous fluids. We highlight a proof-of-principle and describe the working principle for the model compound fluorescein, where the organic solvent DMSO is exchanged against an aqueous buffer. The DMSO removal performance could be significantly increased to 95% by optimization of the microfluidic layout. Moreover, the optimization of the inlet flow ratio resulted in a minimized dilution factor of 5, and we were able to demonstrate that a reduction of the supporting instrumentation is possible without a significant decrease of the DMSO removal performance. Finally, the compatibility of the developed solvent exchanger for cell based downstream applications was proven. The impedimetric monitoring of HEK293A cells in a continuously operating microfluidic setup revealed no adverse effects of the residual DMSO after the solvent replacement. Our solvent exchanger device demonstrates the power of micro-free-flow electrophoresis not only as a powerful technique for separation and purification of compound mixtures but also for solvent replacement.

  9. Cryptanalysis of Wang et al.’s lattice-based key exchange protocol

    Directory of Open Access Journals (Sweden)

    Daya Sagar Gupta

    2016-09-01

    Full Text Available Wang et al. proposed a new hard problem on lattices which is an extension of the small integer solution (SIS on lattices. This new generated hard problem is named to be bilateral in-homogeneous small integer solution (Bi-ISIS. Using the hardness of Bi-ISIS, Wang et al. proposed a new key exchange protocol, which is based on the lattice-based cryptography. In this paper, we signalize that Wang et al.’s lattice-based key exchange protocol is vulnerable to an attack, namely, man-in-the-middle (MITM attack. Through this attack, Eavesdropper can intercept the authenticated messages and communicate the unauthentic messages among the communicating parties.

  10. Dependence and risk assessment for oil prices and exchange rate portfolios: A wavelet based approach

    Science.gov (United States)

    Aloui, Chaker; Jammazi, Rania

    2015-10-01

    In this article, we propose a wavelet-based approach to accommodate the stylized facts and complex structure of financial data, caused by frequent and abrupt changes of markets and noises. Specifically, we show how the combination of both continuous and discrete wavelet transforms with traditional financial models helps improve portfolio's market risk assessment. In the empirical stage, three wavelet-based models (wavelet-EGARCH with dynamic conditional correlations, wavelet-copula, and wavelet-extreme value) are considered and applied to crude oil price and US dollar exchange rate data. Our findings show that the wavelet-based approach provides an effective and powerful tool for detecting extreme moments and improving the accuracy of VaR and Expected Shortfall estimates of oil-exchange rate portfolios after noise is removed from the original data.

  11. Sustainable bio-based materials: opportunities and challenges

    NARCIS (Netherlands)

    van der Meer, Yvonne

    2017-01-01

    Research in the area of bio-based materials aims to achieve breakthroughs in bio-based materials development. A novel way is presented to organise bio-based materials research with a value chain approach in which sustainability research is integrated in the research program. This research approach

  12. Cytotoxicity of a new toothpaste based on an ion exchange resin mixture.

    Science.gov (United States)

    Torrado, Anna; Valiente, Manuel; Zhang, Wu; Li, Yiming; Muñoz, Carlos A

    2005-08-01

    To evaluate the effects for cytotoxicity of two dentifrices: a toothpaste commercially available (Crest Extra-Whitening toothpaste) and a new experimental toothpaste based on a mixture of ion-exchange resins (named NMTD) that supplies calcium, fluoride, phosphate and zinc ions. Cultures of mouse fibroblasts cells L929 were used in a MTT assay for in vitro cytotoxicity of the dentifrices. Cells were cultured in Eagle's minimal essential medium supplemented with 10% fetal bovine serum. Cultures were incubated at 37 degrees C in a humidified atmosphere of 5% CO2 and collected by tripsinization (0.05% trypsin/0.5mM EDTA). A 96-well microplate method was employed for the MTT colorimetric assay. Positive control consisted of 10 microl of phenol in 5 ml of 6% media, a dose that produces zero percent cell survival. Negative control was prepared by adding 0.5 ml of HBSS to 4.5 ml of 6% media. The plates were incubated for 24 and 48 hours at 37 degrees C in a 5% CO2 atmosphere. Means and standard deviations of absorbance values for each group and percentage inhibitory dosage (%ID) for each test material were calculated. None of the dentifrices resulted in a percentage of inhibition higher than 50% and did not observe marked increases in cytotoxicity with time of incubation. The positive control gave almost zero percent cell survival, whereas the negative control gave a hundred percent cell survival. Analysis of the results indicated that test dentifrice dose had no significant effect towards the cell viability (P<0.05).

  13. The Galim LL/EH Polymict Breccia: Evidence for Impact-Induced Exchange Between Reduced and Oxidized Meteoritic Material

    Science.gov (United States)

    Rubin, Alan E.

    1997-01-01

    Galim is a polymict breccia consisting of a heavily shocked (shock stage S6) LL6 chondrite, Galim (a), and an impact-melted EH chondrite, Galim (b). Relict chondrules in Galim (b) served as nucleation sites for euhedral enstatite grains crystallizing from the impact melt. Many of the reduced phases typical of EH chondrites (e.g., Si-bearing metallic Fe-Ni; Ti-bearing troilite) are absent. Galim (b) was probably shock-melted while in contact with a more oxidized source, namely, Galim (a); during this event, Si was oxidized from the metal and Ti was oxidized from troilite. Galim (a) contains shock veins and recrystallized, unzoned olivine. The absence of evidence for reduction in Galim (a) may indicate that the amount of LL material greatly exceeded that of EH material; shock metamorphism may have taken place on the LL parent body. Shock-induced redox reactions such as those inferred for the Galim breccia appear to be restricted mainly to asteroids because the low-end tail of their relative-velocity distribution permits mixing of intact disparate materials (including accretion of projectiles of different oxidation states), whereas the peak of the distribution leads to high equilibration shock pressures (allowing impact-induced exchange between previously accreted, disequilibrated materials). Galim probably formed by a two-stage process: (I) accretion to the LL parent body of an intact EH projectile at low relative velocities, and (2) shock metamorphism of the assemblage by the subsequent impact of another projectile at significantly higher relative velocities.

  14. Study of operating conditions and cell design on the performance of alkaline anion exchange membrane based direct methanol fuel cells

    Science.gov (United States)

    Prakash, G. K. Surya; Krause, Frederick C.; Viva, Federico A.; Narayanan, S. R.; Olah, George A.

    2011-10-01

    Direct methanol fuel cells using an alkaline anion exchange membrane (AAEM) were prepared, studied, and optimized. The effects of fuel composition and electrode materials were investigated. Membrane electrode assemblies fabricated with Tokuyama® AAEM and commercial noble metal catalysts achieved peak power densities between 25 and 168 mW cm-2 depending on the operating temperature, fuel composition, and electrode materials used. Good electrode wettability at the anode was found to be very important for achieving high power densities. The performance of the best AAEM cells was comparable to Nafion®-based cells under similar conditions. Factors limiting the performance of AAEM MEAs were found to be different from those of Nafion® MEAs. Improved electrode kinetics for methanol oxidation in alkaline electrolyte at Pt-Ru are apparent at low current densities. At high current densities, rapid CO2 production converts the hydroxide anions, necessary for methanol oxidation, to bicarbonate and carbonate: consequently, the membrane and interfacial conductivity are drastically reduced. These phenomena necessitate the use of aqueous potassium hydroxide and wettable electrode materials for efficient hydroxide supply to the anode. However, aqueous hydroxide is not needed at the cathode. Compared to AAEM-based fuel cells, methanol fuel cells based on proton-conducting Nafion® retain better performance at high current densities by providing the benefit of carbon dioxide rejection.

  15. Pu Anion Exchange Process Intensification

    Energy Technology Data Exchange (ETDEWEB)

    Taylor-Pashow, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-10-08

    This project seeks to improve the efficiency of the plutonium anion-exchange process for purifying Pu through the development of alternate ion-exchange media. The objective of the project in FY15 was to develop and test a porous foam monolith material that could serve as a replacement for the current anion-exchange resin, Reillex® HPQ, used at the Savannah River Site (SRS) for purifying Pu. The new material provides advantages in efficiency over the current resin by the elimination of diffusive mass transport through large granular resin beads. By replacing the large resin beads with a porous foam there is much more efficient contact between the Pu solution and the anion-exchange sites present on the material. Several samples of a polystyrene based foam grafted with poly(4-vinylpyridine) were prepared and the Pu sorption was tested in batch contact tests.

  16. Materials And Processes Technical Information System (MAPTIS) LDEF materials data base

    Science.gov (United States)

    Funk, Joan G.; Strickland, John W.; Davis, John M.

    1993-01-01

    A preliminary Long Duration Exposure Facility (LDEF) Materials Data Base was developed by the LDEF Materials Special Investigation Group (MSIG). The LDEF Materials Data Base is envisioned to eventually contain the wide variety and vast quantity of materials data generated from LDEF. The data is searchable by optical, thermal, and mechanical properties, exposure parameters (such as atomic oxygen flux) and author(s) or principal investigator(s). Tne LDEF Materials Data Base was incorporated into the Materials and Processes Technical Information System (MAPTIS). MAPTIS is a collection of materials data which has been computerized and is available to engineers, designers, and researchers in the aerospace community involved in the design and development of spacecraft and related hardware. The LDEF Materials Data Base is described and step-by-step example searches using the data base are included. Information on how to become an authorized user of the system is included.

  17. Efficiency of Adaptive Temperature-Based Replica Exchange for Sampling Large-Scale Protein Conformational Transitions.

    Science.gov (United States)

    Zhang, Weihong; Chen, Jianhan

    2013-06-11

    Temperature-based replica exchange (RE) is now considered a principal technique for enhanced sampling of protein conformations. It is also recognized that existence of sharp cooperative transitions (such as protein folding/unfolding) can lead to temperature exchange bottlenecks and significantly reduce the sampling efficiency. Here, we revisit two adaptive temperature-based RE protocols, namely, exchange equalization (EE) and current maximization (CM), that were previously examined using atomistic simulations (Lee and Olson, J. Chem. Physics2011, 134, 24111). Both protocols aim to overcome exchange bottlenecks by adaptively adjusting the simulation temperatures, either to achieve uniform exchange rates (in EE) or to maximize temperature diffusion (CM). By designing a realistic yet computationally tractable coarse-grained protein model, one can sample many reversible folding/unfolding transitions using conventional constant temperature molecular dynamics (MD), standard REMD, EE-REMD, and CM-REMD. This allows rigorous evaluation of the sampling efficiency, by directly comparing the rates of folding/unfolding transitions and convergence of various thermodynamic properties of interest. The results demonstrate that both EE and CM can indeed enhance temperature diffusion compared to standard RE, by ∼3- and over 10-fold, respectively. Surprisingly, the rates of reversible folding/unfolding transitions are similar in all three RE protocols. The convergence rates of several key thermodynamic properties, including the folding stability and various 1D and 2D free energy surfaces, are also similar. Therefore, the efficiency of RE protocols does not appear to be limited by temperature diffusion, but by the inherent rates of spontaneous large-scale conformational rearrangements. This is particularly true considering that virtually all RE simulations of proteins in practice involve exchange attempt frequencies (∼ps(-1)) that are several orders of magnitude faster than the

  18. Shapley Value-Based Payment Calculation for Energy Exchange between Micro- and Utility Grids

    Directory of Open Access Journals (Sweden)

    Robin Pilling

    2017-10-01

    Full Text Available In recent years, microgrids have developed as important parts of power systems and have provided affordable, reliable, and sustainable supplies of electricity. Each microgrid is managed as a single controllable entity with respect to the existing power system but demands for joint operation and sharing the benefits between a microgrid and its hosting utility. This paper is focused on the joint operation of a microgrid and its hosting utility, which cooperatively minimize daily generation costs through energy exchange, and presents a payment calculation scheme for power transactions based on a fair allocation of reduced generation costs. To fairly compensate for energy exchange between the micro- and utility grids, we adopt the cooperative game theoretic solution concept of Shapley value. We design a case study for a fictitious interconnection model between the Mueller microgrid in Austin, Texas and the utility grid in Taiwan. Our case study shows that when compared to standalone generations, both the micro- and utility grids are better off when they collaborate in power exchange regardless of their individual contributions to the power exchange coalition.

  19. Recent Progress on the Key Materials and Components for Proton Exchange Membrane Fuel Cells in Vehicle Applications

    Directory of Open Access Journals (Sweden)

    Cheng Wang

    2016-07-01

    Full Text Available Fuel cells are the most clean and efficient power source for vehicles. In particular, proton exchange membrane fuel cells (PEMFCs are the most promising candidate for automobile applications due to their rapid start-up and low-temperature operation. Through extensive global research efforts in the latest decade, the performance of PEMFCs, including energy efficiency, volumetric and mass power density, and low temperature startup ability, have achieved significant breakthroughs. In 2014, fuel cell powered vehicles were introduced into the market by several prominent vehicle companies. However, the low durability and high cost of PEMFC systems are still the main obstacles for large-scale industrialization of this technology. The key materials and components used in PEMFCs greatly affect their durability and cost. In this review, the technical progress of key materials and components for PEMFCs has been summarized and critically discussed, including topics such as the membrane, catalyst layer, gas diffusion layer, and bipolar plate. The development of high-durability processing technologies is also introduced. Finally, this review is concluded with personal perspectives on the future research directions of this area.

  20. [Preface for special issue on bio-based materials (2016)].

    Science.gov (United States)

    Weng, Yunxuan

    2016-06-25

    Bio-based materials are new materials or chemicals with renewable biomass as raw materials such as grain, legume, straw, bamboo and wood powder. This class of materials includes bio-based polymer, biobased fiber, glycotechnology products, biobased rubber and plastics produced by biomass thermoplastic processing and basic biobased chemicals, for instance, bio-alcohols, organic acids, alkanes, and alkenes, obtained by bio-synthesis, bio-processing and bio-refinery. Owing to its environmental friendly and resource conservation, bio-based materials are becoming a new dominant industry taking the lead in the world scientific and technological innovation and economic development. An overview of bio-based materials development is reported in this special issue, and the industrial status and research progress of the following aspects, including biobased fiber, polyhydroxyalkanoates, biodegradable mulching film, bio-based polyamide, protein based biomedical materials, bio-based polyurethane, and modification and processing of poly(lactic acid), are introduced.

  1. The development of an internet-based knowledge exchange platform for pediatric critical care clinicians worldwide*.

    Science.gov (United States)

    Wolbrink, Traci A; Kissoon, Niranjan; Burns, Jeffrey P

    2014-03-01

    Advances in Internet technology now enable unprecedented global collaboration and collective knowledge exchange. Up to this time, there have been limited efforts to use these technologies to actively promote knowledge exchange across the global pediatric critical care community. To develop an open-access, peer-reviewed, not-for-profit Internet-based learning application, OPENPediatrics, a collaborative effort with the World Federation of Pediatric Intensive and Critical Care Societies, was designed to promote postgraduate educational knowledge exchange for physicians, nurses, and others caring for critically ill children worldwide. Description of program development. International multicenter tertiary pediatric critical care units across six continents. Multidisciplinary pediatric critical care providers. A software application, providing information on demand, curricular pathways, and videoconferencing, downloaded to a local computer. In 2010, a survey assessing postgraduate educational needs was distributed through World Federation of Pediatric Intensive and Critical Care Societies to constituent societies. Four hundred and twenty-nine critical care providers from 49 countries responded to the single e-mail survey request. Respondents included 68% physicians and 28% nurses who care for critically ill children. Fifty-two percent of respondents reported accessing the Internet at least weekly to obtain professional educational information. The five highest requests were for educational content on respiratory care [mechanical ventilation] (48% [38%]), sepsis (28%), neurology (25%), cardiology (14%), extracorporeal membrane oxygenation (10%), and ethics (8%). Based on these findings, and in collaboration with researchers in adult learning and online courseware, an application was developed and is currently being used by 770 registered users in 60 countries. We describe here the development and implementation of an Internet-based application which is among the first

  2. The CROPROTECT project and wider opportunities to improve farm productivity through web?based knowledge exchange

    OpenAIRE

    Bruce, Toby J. A.

    2016-01-01

    Abstract A key global 21st century challenge is to maximize agricultural production while minimizing use of resources such as land, water, and energy to meet rising demand for produce. To meet this challenge, while also adapting to climate change, agriculture will have to become more knowledge intensive and deploy smarter farming techniques. The intention of this study was to: (1) Highlight the opportunity for web?based knowledge exchange to increase farm productivity and thus contribute to a...

  3. The preliminary Long Duration Exposure Facility (LDEF) materials data base

    Science.gov (United States)

    Funk, Joan G.; Strickland, John W.; Davis, John M.

    1992-01-01

    A preliminary Long Duration Exposure Facility (LDEF) Materials Data Base was developed by the LDEF Materials Special Investigation Group (MSIG). The LDEF Materials Data Base is envisioned to eventually contain the wide variety and vast quantity of materials data generated for LDEF. The data is searchable by optical, thermal, and mechanical properties, exposure parameters (such as atomic oxygen flux), and author(s) or principal investigator(s). The LDEF Materials Data Base was incorporated into the Materials and Processes Technical Information System (MAPTIS). MAPTIS is a collection of materials data which was computerized and is available to engineers, designers, and researchers in the aerospace community involved in the design and development of spacecraft and related hardware. This paper describes the LDEF Materials Data Base and includes step-by-step example searches using the data base. Information on how to become an authorized user of the system is included.

  4. Microspherical inorganic ion-exchangers based on cenospheres of coal fly ash

    Energy Technology Data Exchange (ETDEWEB)

    T.A. Vereshchagina; E.V. Fomenko; S.N. Vereshchagin; N.N. Shishkina; N.G. Vasilieva; E.N. Paretskov; D.M. Kruchek; T.J. Tranter; A.G. Anshits [Institute of Chemistry and Chemical Technology SB RAS, Krasnoyarsk (Russian Federation)

    2005-07-01

    Coal fly ash cenospheres are very promising for a variety of applications, such as production of porous materials, sensitisers of emulsion explosives, adsorbents, catalysts, etc. One of the interesting areas of cenosphere application is generation of microspherical ion-exchangers for immobilization of liquid radioactive waste, which are active in trapping radionuclides from radioactive solutions and, at a final step, can serve as a matrix for radionuclide disposal in the form of stable mineral-like compounds. It was demonstrated that two types of microspherical ion-exchangers, such as (I) encapsulated inorganic ion-exchangers and (ii) cenosphere-derived zeolites, could be prepared on cenospheres. It was shown that chemical modification of cenospheres by etching with mineral acids results in formation of open pores in the cenosphere wall. Depending on the nature of acid, one can obtain hollow microspheres with porous walls of different specific surface area (30-50 m{sup 2}/g for HCl etched cenospheres and 1-2 m{sup 2}/g for HF etched ones) and morphology. Cenosphere species with a macroporous permeable wall is a suitable support for encapsulation of active additives inside the perforated spheres. In this work a number of encapsulated sorbents of {sup 137}Cs{sup +}, such as ammonium molybdophosphate, copper, nickel and iron-ferrocyanides, zirconium phosphate, were obtained. Cenosphere-derived zeolites of NaP, NaX and NaA types were obtained by the hydrothermal treatment of cenospheres in the presence of alkaline solutions. Properties of the encapsulated ion-exchangers and microspherical zeolites were studied in Cs{sup +} and Sr{sup 2+} sorption from simulant solutions of different composition. Sorbents impregnated with radionuclides were shown to convert into stable crystalline compounds under thermal and thermobaric treatment. 19 refs., 5 figs., 3 tabs.

  5. Geo3DML: A standard-based exchange format for 3D geological models

    Science.gov (United States)

    Wang, Zhangang; Qu, Honggang; Wu, Zixing; Wang, Xianghong

    2018-01-01

    A geological model (geomodel) in three-dimensional (3D) space is a digital representation of the Earth's subsurface, recognized by geologists and stored in resultant geological data (geodata). The increasing demand for data management and interoperable applications of geomodelscan be addressed by developing standard-based exchange formats for the representation of not only a single geological object, but also holistic geomodels. However, current standards such as GeoSciML cannot incorporate all the geomodel-related information. This paper presents Geo3DML for the exchange of 3D geomodels based on the existing Open Geospatial Consortium (OGC) standards. Geo3DML is based on a unified and formal representation of structural models, attribute models and hierarchical structures of interpreted resultant geodata in different dimensional views, including drills, cross-sections/geomaps and 3D models, which is compatible with the conceptual model of GeoSciML. Geo3DML aims to encode all geomodel-related information integrally in one framework, including the semantic and geometric information of geoobjects and their relationships, as well as visual information. At present, Geo3DML and some supporting tools have been released as a data-exchange standard by the China Geological Survey (CGS).

  6. A PEM fuel cell based on electrocatalyst and membrane materials modified by PANAM dendrimers

    Energy Technology Data Exchange (ETDEWEB)

    Ledesma-Garcia, J.; Chapman, T.W.; Godinez, L.A. [Centro de Investigacion y Desarrollo Tecnologico en Electroquimica, Queretaro (Mexico)

    2008-10-15

    Due to its high energy conversion efficiency and low emission of pollutants, fuel-cell technology has been generally recognized as a key twenty-first century energy source. For polymer electrolyte membrane fuel cells (PEMFC), it has been found that platinum and its alloys exhibit the best electrocatalytic activity for oxygen reduction. The highest electrocatalytic activity of platinum and its alloys can be achieved when the particles are produced in the nanometer range. In this context, organic molecules have been adopted as templates to control the size of metal nanoparticles. Dendrimers, in particular, have shown promising properties for this application, and strategies that include direct adsorption, electrostatic attachment and covalent bonding have been developed for connecting metal-bearing dendrimers to conducting substrates. This paper reported on the preliminary results of a study that involved the construction and testing of a hydrogen-oxygen PEM fuel cell based on carbon-fiber-paper electrodes coated with hydroxyl-terminated dendrimers that encapsulated nanoparticles of platinum. This prototype cell also employed an ion exchange membrane comprising a cellulose acetate filter functionalized with proton-exchanging dendrimers. A proton-exchange membrane was prepared by binding duplex amine-carboxylate dendrimers to a cellulose-acetate support. With these dendrimer-based materials, a hydrogen-oxygen fuel cell was assembled and the performance compared with cells prepared with Nafion-based membranes. The voltage-current profiles and the power-density curves from the new cell provide encouragement to continue work with these dendrimer-modified materials. The paper discussed the experimental methods, with particular reference to materials; electrode preparation and characterization; proton-exchange membrane preparation; and PEM fuel-cell assembly and testing. It was concluded that the use of the dendritic macromolecules as supports for the nanoparticulate

  7. Exchange Network

    Science.gov (United States)

    The Environmental Information Exchange Network (EIEN) is an Internet-based system used by state, tribal and territorial partners to securely share environmental and health information with one another and EPA.

  8. Forensic Identification Based on Tooth Material

    National Research Council Canada - National Science Library

    Elza Ibrahim Auerkari; Archinantinigsih Surjadi

    2015-01-01

    Human teeth are the most robust and stable parts of the body, providing biological clue material for forensic purposes even when most of the oter means of identifcation have been seriously affected...

  9. Forensic Identification Based on Tooth Material

    National Research Council Canada - National Science Library

    Elza Ibrahim Auerkari; Archinantinigsih Surjadi

    2015-01-01

    .... While in general the value of traditional dental records in the forensic work is decreasing eg due to mproved dental care, the newer means of identification from tooth material provide considerable...

  10. Friction and wear in polymer-based materials

    CERN Document Server

    Bely, V A; Petrokovets, M I

    1982-01-01

    Friction and Wear in Polymer-Based Materials discusses friction and wear problems in polymer-based materials. The book is organized into three parts. The chapters in Part I cover the basic laws of friction and wear in polymer-based materials. Topics covered include frictional interaction during metal-polymer contact and the influence of operating conditions on wear in polymers. The chapters in Part II discuss the structure and frictional properties of polymer-based materials; the mechanism of frictional transfer when a polymer comes into contact with polymers, metals, and other materials; and

  11. Graphene-based materials for tissue engineering

    OpenAIRE

    Shin, Su Ryon; Li, Yi-Chen; Jang, HaeLin; Khoshakhlagh, Parastoo; Akbari, Mohsen; Nasajpour, Amir; Zhang, Yu Shrike; Tamayol, Ali; Khademhosseini, Ali

    2016-01-01

    Graphene and its chemical derivatives have been a pivotal new class of nanomaterials and a model system for quantum behavior. The material's excellent electrical conductivity, biocompatibility, surface area and thermal properties are of much interest to the scientific community. Two dimensional graphene materials have been widely used in various biomedical research areas such as bioelectronics, imaging, drug delivery, and tissue engineering. In this review we will highlight the recent applica...

  12. Using a Theory-Consistent CVAR Scenario to Test an Exchange Rate Model Based on Imperfect Knowledge

    DEFF Research Database (Denmark)

    Juselius, Katarina

    2017-01-01

    -state behavior of an an imperfect knowledge based model for exchange rate determination can be formulated as testable hypotheses on common stochastic trends and cointegration. This model obtained a remarkable support for almost every testable hypothesis and was able to adequately account for the long persistent...... swings in the real exchange rate....

  13. Characterization of proton exchange membrane materials for fuel cells by solid state nuclear magnetic resonance

    Energy Technology Data Exchange (ETDEWEB)

    Kong, Zueqian [Iowa State Univ., Ames, IA (United States)

    2010-01-01

    Solid-state nuclear magnetic resonance (NMR) has been used to explore the nanometer-scale structure of Nafion, the widely used fuel cell membrane, and its composites. We have shown that solid-state NMR can characterize chemical structure and composition, domain size and morphology, internuclear distances, molecular dynamics, etc. The newly-developed water channel model of Nafion has been confirmed, and important characteristic length-scales established. Nafion-based organic and inorganic composites with special properties have also been characterized and their structures elucidated. The morphology of Nafion varies with hydration level, and is reflected in the changes in surface-to-volume (S/V) ratio of the polymer obtained by small-angle X-ray scattering (SAXS). The S/V ratios of different Nafion models have been evaluated numerically. It has been found that only the water channel model gives the measured S/V ratios in the normal hydration range of a working fuel cell, while dispersed water molecules and polymer ribbons account for the structures at low and high hydration levels, respectively.

  14. Modelling, simulation and geometric optimization of cross flow recuperative heat exchanger based on controllability condition number

    Directory of Open Access Journals (Sweden)

    Stević Dalibor

    2017-01-01

    Full Text Available This paper presents the algebraic mathematical model of cross - flow heat exchanger derived on the basis of transport approach. Theirs operation in the face of variable loads is usually controlled by manipulating inlet fluid temperatures or mass flow rates, where the controlled variable is usually the output temperature of principal flow. The aim of this paper is to optimize the geometry of a tube with the inlet flow of principal incompressible fluid and an external cross - country flow of compressible fluid, based on performance index expressed throughout its controllability characteristics. Thus the condition number has been used to provide the necessary information on the best situation for control of the exchanger under consideration. This concept can also provide us with information about the easiest operating condition to control a particular output. A transient model of a cross-flow heat exchanger is developed, where an implicit formulation is used for transient numerical solutions. The condition number performed throughout the ratio of geometric parameters of tube is optimized, subject to volume constraints, based on the optimum operation in terms of output controllability. The reported optimized aspect ratio, water mass flow rate and output controllability are studied for different external properties of the tube.

  15. Development of a plastic rotary heat exchanger for room-based ventilation in existing apartments

    DEFF Research Database (Denmark)

    Smith, Kevin Michael; Svendsen, Svend

    2015-01-01

    for single-room ventilation based on thermal design theory. Performance is predicted from correlations of dimensionless groups for regenerative heat exchangers, and this guides the selection of a polycarbonate honeycomb with small circular channels. Experiments quantify flows and determine temperature......The existing building stock will likely undergo widespread energy renovations to meet future emissions targets. Single-room ventilation may enable the process due to its simple installation, low fan power, and potential for local heat recovery. A short plastic rotary heat exchanger is developed...... efficiencies at several ventilation rates while accounting for heat gains from motors and air leakage. The measured and modelled temperature efficiencies show adequate agreement and exceed 80% for a balanced nominal ventilation rate of 28m3/h. This result meets the development criteria but cannot validate...

  16. Design and evaluation of foamed asphalt base materials : [research summary].

    Science.gov (United States)

    2013-05-01

    Foamed asphalt stabilized base (FASB) combines reclaimed asphalt pavement (RAP), : recycled concrete (RC), and/or graded aggregate base (GAB) with a foamed asphalt : binder to produce a partially stabilized base material. Although widely used, most :...

  17. A silica nanoparticle based ionic material

    Science.gov (United States)

    Fernandes, Nikhil; Azad, Zubair; Giannelis, Emmanuel

    2011-03-01

    We report an ionic fluid consisting of silica nanoparticles as the anion, and amine-terminated polyethylene glycol as the cation. Unlike previous work that has required chemical functionalization of the silica surface, the charge on the nanoparticle anion is carried by the intrinsic surface hydroxyls, simplifying the synthesis, and thus making this a simple test system to probe the physics of these nanoscale ionic materials. Charge and steric factors result in excellent dispersion of the nanoparticles in the polymer matrix. The resulting material is a soft glass that has thermal and rheological properties that depend on the silica:polymer ratio. In particular, at a critical silica:polymer ratio, the ionic material shows a significant depression of the normalized heat of melting and the melting temperature compared to samples with higher or lower silica content (showing eutectic-like behaviour), and to controls without the ionic interaction between the polymer and the particle. Funded by KAUST-CU.

  18. Supercapacitors based on graphene/pseudocapacitive materials

    Directory of Open Access Journals (Sweden)

    Sačer Denis

    2017-01-01

    Full Text Available Composites of graphene and SnO2 were successfully prepared by a single step simultaneous synthesis of SnO2 and reduction of graphene oxide (GO. Three different compositions of precursor solution resulted in different composite materials containing graphene and SnO2. The reaction was realized by microwave-assisted hydrothermal synthesis. Scanning electron microscopy (SEM and energy-dispersive X-ray spectroscopy (EDX gave insight into the morphology and composition of the obtained materials. Good capacitive/pseudocapacitive properties of the obtained material suitable for supercapacitor application were registered by cyclic voltammetry, from where specific capacitance values up to 93 F g-1 were determined. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 172060

  19. Estimation of Hydrogen-Exchange Protection Factors from MD Simulation Based on Amide Hydrogen Bonding Analysis

    Science.gov (United States)

    Park, In-Hee; Venable, John D.; Steckler, Caitlin; Cellitti, Susan E.; Lesley, Scott A.; Spraggon, Glen; Brock, Ansgar

    2015-01-01

    Hydrogen exchange (HX) studies have provided critical insight into our understanding of protein folding, structure and dynamics. More recently, Hydrogen Exchange Mass Spectrometry (HX-MS) has become a widely applicable tool for HX studies. The interpretation of the wealth of data generated by HX-MS experiments as well as other HX methods would greatly benefit from the availability of exchange predictions derived from structures or models for comparison with experiment. Most reported computational HX modeling studies have employed solvent-accessible-surface-area based metrics in attempts to interpret HX data on the basis of structures or models. In this study, a computational HX-MS prediction method based on classification of the amide hydrogen bonding modes mimicking the local unfolding model is demonstrated. Analysis of the NH bonding configurations from Molecular Dynamics (MD) simulation snapshots is used to determine partitioning over bonded and non-bonded NH states and is directly mapped into a protection factor (PF) using a logistics growth function. Predicted PFs are then used for calculating deuteration values of peptides and compared with experimental data. Hydrogen exchange MS data for Fatty acid synthase thioesterase (FAS-TE) collected for a range of pHs and temperatures was used for detailed evaluation of the approach. High correlation between prediction and experiment for observable fragment peptides is observed in the FAS-TE and additional benchmarking systems that included various apo/holo proteins for which literature data were available. In addition, it is shown that HX modeling can improve experimental resolution through decomposition of in-exchange curves into rate classes, which correlate with prediction from MD. Successful rate class decompositions provide further evidence that the presented approach captures the underlying physical processes correctly at the single residue level. This assessment is further strengthened in a comparison of

  20. Adsorption of arsenite and selenite using an inorganic ion exchanger based on Fe–Mn hydrous oxide

    KAUST Repository

    Szlachta, Małgorzata

    2012-01-01

    The adsorption behaviour and mechanism of As(III) and Se(IV) oxyanion uptake using a mixed inorganic adsorbent were studied. The novel adsorbent, based on Fe(III)-Mn(III) hydrous oxides and manganese(II) carbonate, was synthesised using a hydrothermal precipitation approach in the presence of urea. The inorganic ion exchanger exhibited a high selectivity and adsorptive capacity towards As(III) (up to 47.6mg/g) and Se(IV) (up to 29.0mg/g), even at low equilibrium concentration. Although pH effects were typical for anionic species (i.e., the adsorption decreased upon pH increase), Se(IV) was more sensitive to pH changes than As(III). The rates of adsorption of both oxyanions were high. Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) studies showed that the ion exchange adsorption of both anions took place via OH - groups, mainly from Fe(III) but also Mn(III) hydrous oxides. MnCO 3 did not contribute directly to As(III) and Se(IV) removal. A higher adsorptive capacity of the developed material towards As(III) was partly due to partial As(III) oxidation during adsorption. © 2011 Elsevier Inc.

  1. Ion Exchange Formation via Sulfonated Bicomponent Nonwovens

    Science.gov (United States)

    Stoughton, Hannah L.

    For many years ion exchange resins were used to: remove heavy metals from water, recover materials from wastewater, and eliminate harmful gases from the air. While use of these resin beads dominates the ion exchange industry, the beads have limitations that should be considered when decisions are made to employ them. For instance, officials must balance the inherent zero sum surface area and porosity of the materials. This series of studies investigates the use of bicomponent nonwovens as a base substrate for producing high surface area ion exchange materials for the removal of heavy metal ions. Functionalized materials were produced in a two-step process: (1) PET/PE spunbond bicomponent fibers were fractured completely, producing the high surface area nonwoven to be used as the base ion exchange material, and (2) the conditions for functionalizing the PET fibers of the nonwoven webs were investigated where an epoxy containing monomer was grafted to the surface followed by sulfonation of the monomer. The functionalization reactions of the PET fibers were monitored based on: weight gain, FTIR, TOF-SIMS, and SEM. Ion exchange properties were evaluated using titration and copper ion removal capacity from test solutions. The relationship between web structure and removal efficiency of the metal ions was defined through a comparison of the bicomponent and homocomponent nonwovens for copper ion removal efficiency. The investigation revealed that utilizing the high surface area, fractured bicomponent nonwoven ion exchange materials with capacities comparable to commercially available ion exchange resins could be produced.

  2. Light Spins of Cylindrical Electromagnetic Waves and their Jumps across Material Interfaces in the Presence of Energy Exchange

    Directory of Open Access Journals (Sweden)

    J. Mok

    2016-08-01

    Full Text Available We investigate light spins for cylindrical electromagnetic waves on resonance. To this goal, we consider both a dielectric cylinder of infinite length immersed in vacuum and a cylindrical hole punched through a dense dielectric medium. In order for waves of constant frequencies to be established through lossless media, energy absorption is allowed in the surrounding medium to compensate for radiation loss. The dispersion relation is then numerically solved for an asymmetry parameter implying a balance in energy exchange. Numerical studies are performed by varying parameters of refractive index contrast, azimuthal mode index, and size parameter of a cylindrical object. The resulting data is presented mostly in terms of a specific spin, defined as light spin per energy density. This specific spin is found to be bounded in its magnitude, with its maximum associated with either optical vortices or large rotations. Depending on parametric combinations, the specific spin could not only undergo finite jumps across the material interface but also exhibit limit behaviors.

  3. Indoor Solar Thermal Energy Saving Time with Phase Change Material in a Horizontal Shell and Finned-Tube Heat Exchanger

    Directory of Open Access Journals (Sweden)

    S. Paria

    2015-01-01

    Full Text Available An experimental as well as numerical investigation was conducted on the melting/solidification processes of a stationary phase change material (PCM in a shell around a finned-tube heat exchanger system. The PCM was stored in the horizontal annular space between a shell and finned-tube where distilled water was employed as the heat transfer fluid (HTF. The focus of this study was on the behavior of PCM for storage (charging or melting and removal (discharging or solidification, as well as the effect of flow rate on the charged and discharged solar thermal energy. The impact of the Reynolds number was determined and the results were compared with each other to reveal the changes in amount of stored thermal energy with the variation of heat transfer fluid flow rates. The results showed that, by increasing the Reynolds number from 1000 to 2000, the total melting time decreases by 58%. The process of solidification also will speed up with increasing Reynolds number in the discharging process. The results also indicated that the fluctuation of gradient temperature decreased and became smooth with increasing Reynolds number. As a result, by increasing the Reynolds number in the charging process, the theoretical efficiency rises.

  4. Indoor solar thermal energy saving time with phase change material in a horizontal shell and finned-tube heat exchanger.

    Science.gov (United States)

    Paria, S; Sarhan, A A D; Goodarzi, M S; Baradaran, S; Rahmanian, B; Yarmand, H; Alavi, M A; Kazi, S N; Metselaar, H S C

    2015-01-01

    An experimental as well as numerical investigation was conducted on the melting/solidification processes of a stationary phase change material (PCM) in a shell around a finned-tube heat exchanger system. The PCM was stored in the horizontal annular space between a shell and finned-tube where distilled water was employed as the heat transfer fluid (HTF). The focus of this study was on the behavior of PCM for storage (charging or melting) and removal (discharging or solidification), as well as the effect of flow rate on the charged and discharged solar thermal energy. The impact of the Reynolds number was determined and the results were compared with each other to reveal the changes in amount of stored thermal energy with the variation of heat transfer fluid flow rates. The results showed that, by increasing the Reynolds number from 1000 to 2000, the total melting time decreases by 58%. The process of solidification also will speed up with increasing Reynolds number in the discharging process. The results also indicated that the fluctuation of gradient temperature decreased and became smooth with increasing Reynolds number. As a result, by increasing the Reynolds number in the charging process, the theoretical efficiency rises.

  5. Numerical Study of Solidification in a Plate Heat Exchange Device with a Zigzag Configuration Containing Multiple Phase-Change-Materials

    Directory of Open Access Journals (Sweden)

    Peilun Wang

    2016-05-01

    Full Text Available Latent heat thermal energy storage (TES plays an important role in the advocation of TES in contrast to sensible energy storage because of the large storage energy densities per unit mass/volume possible at a nearly constant thermal energy. In the current study, a heat exchange device with a zigzag configuration containing multiple phase-change-materials (m-PCMs was considered, and an experimental system was built to validate the model for a single PCM. A two-dimensional numerical model was developed using the ANSYS Fluent 14.0 software program. The energy fractions method was put forward to calculate the average Ste number and the influence of Re and Ste numbers on the discharge process were studied. The influence of phase change temperature among m-PCMs on the solidification process has also been studied. A new boundary condition was defined to determine the combined effect of the Re and Ste numbers on the discharging process. The modelling results show that for a given input power, the Ste (or Re number has a significant impact on the discharging process; however, the period value of inlet velocity has almost no impact on it. Besides, the zigzag plate with m-PCMs has a good impact on the temperature shock as “filter action” in the discharging process.

  6. Guidelines for selecting weak-base versus strong-base anion-exchange resins for the recovery of chromate from cooling tower blowdown

    Energy Technology Data Exchange (ETDEWEB)

    Newman, J.; Reed, L.W.

    1980-01-01

    Guidelines for selecting weak-base versus strong-base anion-exchange resins for the recovery of chromate from cooling tower blowdown are given, together with actual operating data on large-scale industrial systems based on strong-base anion-exchange resins, data from a similar pilot system based on weak-base anion resin, and the chemical costs for operating both systems for a cooling tower blowdown containing 2500 ppm total dissolved solids and 20 ppm chromata.

  7. Acetylene-Based Materials in Organic Photovoltaics

    Science.gov (United States)

    Silvestri, Fabio; Marrocchi, Assunta

    2010-01-01

    Fossil fuel alternatives, such as solar energy, are moving to the forefront in a variety of research fields. Organic photovoltaic systems hold the promise of a lightweight, flexible, cost-effective solar energy conversion platform, which could benefit from simple solution-processing of the active layer. The discovery of semiconductive polyacetylene by Heeger et al. in the late 1970s was a milestone towards the use of organic materials in electronics; the development of efficient protocols for the palladium catalyzed alkynylation reactions and the new conception of steric and conformational advantages of acetylenes have been recently focused the attention on conjugated triple-bond containing systems as a promising class of semiconductors for OPVs applications. We review here the most important and representative (poly)arylacetylenes that have been used in the field. A general introduction to (poly)arylacetylenes, and the most common synthetic approaches directed toward making these materials will be firstly given. After a brief discussion on working principles and critical parameters of OPVs, we will focus on molecular arylacetylenes, (co)polymers containing triple bonds, and metallopolyyne polymers as p-type semiconductor materials. The last section will deal with hybrids in which oligomeric/polymeric structures incorporating acetylenic linkages such as phenylene ethynylenes have been attached onto C60, and their use as the active materials in photovoltaic devices. PMID:20480031

  8. Acetylene-Based Materials in Organic Photovoltaics

    Directory of Open Access Journals (Sweden)

    Fabio Silvestri

    2010-04-01

    Full Text Available Fossil fuel alternatives, such as solar energy, are moving to the forefront in a variety of research fields. Organic photovoltaic systems hold the promise of a lightweight, flexible, cost-effective solar energy conversion platform, which could benefit from simple solution-processing of the active layer. The discovery of semiconductive polyacetylene by Heeger et al. in the late 1970s was a milestone towards the use of organic materials in electronics; the development of efficient protocols for the palladium catalyzed alkynylation reactions and the new conception of steric and conformational advantages of acetylenes have been recently focused the attention on conjugated triple-bond containing systems as a promising class of semiconductors for OPVs applications. We review here the most important and representative (polyarylacetylenes that have been used in the field. A general introduction to (polyarylacetylenes, and the most common synthetic approaches directed toward making these materials will be firstly given. After a brief discussion on working principles and critical parameters of OPVs, we will focus on molecular arylacetylenes, (copolymers containing triple bonds, and metallopolyyne polymers as p-type semiconductor materials. The last section will deal with hybrids in which oligomeric/polymeric structures incorporating acetylenic linkages such as phenylene ethynylenes have been attached onto C60, and their use as the active materials in photovoltaic devices.

  9. Optical Limiting Materials Based on Gold Nanoparticles

    Science.gov (United States)

    2014-04-30

    F. A Review of Optical Limiting Mechanisms and Devices Using Organics, Fullerenes , Semiconductors and Other Materials. Prog. Quant. Electr. 1993...information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering...and maintaining the data needed, and completing and reviewing this collection of information. Send comments regarding this burden estimate or any

  10. Acetylene-based materials in organic photovoltaics.

    Science.gov (United States)

    Silvestri, Fabio; Marrocchi, Assunta

    2010-04-08

    Fossil fuel alternatives, such as solar energy, are moving to the forefront in a variety of research fields. Organic photovoltaic systems hold the promise of a lightweight, flexible, cost-effective solar energy conversion platform, which could benefit from simple solution-processing of the active layer. The discovery of semiconductive polyacetylene by Heeger et al. in the late 1970s was a milestone towards the use of organic materials in electronics; the development of efficient protocols for the palladium catalyzed alkynylation reactions and the new conception of steric and conformational advantages of acetylenes have been recently focused the attention on conjugated triple-bond containing systems as a promising class of semiconductors for OPVs applications. We review here the most important and representative (poly)arylacetylenes that have been used in the field. A general introduction to (poly)arylacetylenes, and the most common synthetic approaches directed toward making these materials will be firstly given. After a brief discussion on working principles and critical parameters of OPVs, we will focus on molecular arylacetylenes, (co)polymers containing triple bonds, and metallopolyyne polymers as p-type semiconductor materials. The last section will deal with hybrids in which oligomeric/polymeric structures incorporating acetylenic linkages such as phenylene ethynylenes have been attached onto C(60), and their use as the active materials in photovoltaic devices.

  11. Geopolymer materials based on natural zeolite

    NARCIS (Netherlands)

    Nikolov, A.; Rostovsky, Ivan; Nugteren, H.W.

    2017-01-01

    One of the potential raw materials for preparation of geopolymers is the natural zeolite. In the present report, the used natural zeolite (clinoptilolite) is from huge deposit near Beli Plast, Bulgaria. Geopolymer pastes and mortars are prepared by using three different alkaline activators—sodium

  12. General practice based teaching exchanges in Europe. Experiences from the EU Socrates programme 'primary health care'.

    Science.gov (United States)

    van Weel, Chris; Mattsson, Bengt; Freeman, George K; de Meyere, Marc; von Fragstein, Martin

    2005-01-01

    This paper reviews the experience of international exchange of medical students for general practice. The experience is based on the EU Socrates programme 'Primary Health Care' that offers, since 1992, clinical attachments and research electives in primary care. This programme involves 11 university departments of general practice/primary care in eight countries: Austria - Vienna; Belgium - Gent; Germany Düsseldorf; Italy - Monza, Udine; Netherlands Nijmegen; Slovenia - Ljubljana; Sweden - Göteborg; and the UK - Edinburgh, Imperial College London and Nottingham. More than 150 students have taken part in the programme, most in the last four years. For clinical attachment communication to patients is essential, and students should be able to speak the language of the host university. A research elective in primary care is less demanding and requires students' ability to communicate in English. Despite marked differences in health care structure in the countries involved, it is quite possible to provide a valuable teaching environment in general practice, and the experience gained by students in the exchanges more than equals that what they would gain at home. The added value is in experiencing the influence of another health care system and of working in another academic primary care centre. A substantial number of research electives have been published in international peer reviewed scientific journals with the student as first (occasionally second) author and staff members of the student's host and home university as co-authors. A further benefit of the exchange programme lies in the transfer teaching innovations between universities.

  13. Fault Diagnosis for the Heat Exchanger of the Aircraft Environmental Control System Based on the Strong Tracking Filter

    Science.gov (United States)

    Ma, Jian; Lu, Chen; Liu, Hongmei

    2015-01-01

    The aircraft environmental control system (ECS) is a critical aircraft system, which provides the appropriate environmental conditions to ensure the safe transport of air passengers and equipment. The functionality and reliability of ECS have received increasing attention in recent years. The heat exchanger is a particularly significant component of the ECS, because its failure decreases the system’s efficiency, which can lead to catastrophic consequences. Fault diagnosis of the heat exchanger is necessary to prevent risks. However, two problems hinder the implementation of the heat exchanger fault diagnosis in practice. First, the actual measured parameter of the heat exchanger cannot effectively reflect the fault occurrence, whereas the heat exchanger faults are usually depicted by utilizing the corresponding fault-related state parameters that cannot be measured directly. Second, both the traditional Extended Kalman Filter (EKF) and the EKF-based Double Model Filter have certain disadvantages, such as sensitivity to modeling errors and difficulties in selection of initialization values. To solve the aforementioned problems, this paper presents a fault-related parameter adaptive estimation method based on strong tracking filter (STF) and Modified Bayes classification algorithm for fault detection and failure mode classification of the heat exchanger, respectively. Heat exchanger fault simulation is conducted to generate fault data, through which the proposed methods are validated. The results demonstrate that the proposed methods are capable of providing accurate, stable, and rapid fault diagnosis of the heat exchanger. PMID:25823010

  14. Fault diagnosis for the heat exchanger of the aircraft environmental control system based on the strong tracking filter.

    Science.gov (United States)

    Ma, Jian; Lu, Chen; Liu, Hongmei

    2015-01-01

    The aircraft environmental control system (ECS) is a critical aircraft system, which provides the appropriate environmental conditions to ensure the safe transport of air passengers and equipment. The functionality and reliability of ECS have received increasing attention in recent years. The heat exchanger is a particularly significant component of the ECS, because its failure decreases the system's efficiency, which can lead to catastrophic consequences. Fault diagnosis of the heat exchanger is necessary to prevent risks. However, two problems hinder the implementation of the heat exchanger fault diagnosis in practice. First, the actual measured parameter of the heat exchanger cannot effectively reflect the fault occurrence, whereas the heat exchanger faults are usually depicted by utilizing the corresponding fault-related state parameters that cannot be measured directly. Second, both the traditional Extended Kalman Filter (EKF) and the EKF-based Double Model Filter have certain disadvantages, such as sensitivity to modeling errors and difficulties in selection of initialization values. To solve the aforementioned problems, this paper presents a fault-related parameter adaptive estimation method based on strong tracking filter (STF) and Modified Bayes classification algorithm for fault detection and failure mode classification of the heat exchanger, respectively. Heat exchanger fault simulation is conducted to generate fault data, through which the proposed methods are validated. The results demonstrate that the proposed methods are capable of providing accurate, stable, and rapid fault diagnosis of the heat exchanger.

  15. Fault diagnosis for the heat exchanger of the aircraft environmental control system based on the strong tracking filter.

    Directory of Open Access Journals (Sweden)

    Jian Ma

    Full Text Available The aircraft environmental control system (ECS is a critical aircraft system, which provides the appropriate environmental conditions to ensure the safe transport of air passengers and equipment. The functionality and reliability of ECS have received increasing attention in recent years. The heat exchanger is a particularly significant component of the ECS, because its failure decreases the system's efficiency, which can lead to catastrophic consequences. Fault diagnosis of the heat exchanger is necessary to prevent risks. However, two problems hinder the implementation of the heat exchanger fault diagnosis in practice. First, the actual measured parameter of the heat exchanger cannot effectively reflect the fault occurrence, whereas the heat exchanger faults are usually depicted by utilizing the corresponding fault-related state parameters that cannot be measured directly. Second, both the traditional Extended Kalman Filter (EKF and the EKF-based Double Model Filter have certain disadvantages, such as sensitivity to modeling errors and difficulties in selection of initialization values. To solve the aforementioned problems, this paper presents a fault-related parameter adaptive estimation method based on strong tracking filter (STF and Modified Bayes classification algorithm for fault detection and failure mode classification of the heat exchanger, respectively. Heat exchanger fault simulation is conducted to generate fault data, through which the proposed methods are validated. The results demonstrate that the proposed methods are capable of providing accurate, stable, and rapid fault diagnosis of the heat exchanger.

  16. Identity-based authenticated key exchange protocols from the Tate pairing

    Science.gov (United States)

    Shen, Jun; Jin, Hong; Yang, Zhiyong; Cui, Xiang

    2011-12-01

    Key agreement protocols are designed to establish a session keys between two or multiple entities oven an insecure network and the session key is used to assure confidentiality thought encryption. With the advantages of identity-based (ID-based) cryptography, there have been many ID-based key agreement protocols proposed. However, most of them are based on Weil pairing, which is more cost of computation compared with Tate paring. In this paper, we propose a newly ID-based key agreement protocol from the Tate pairing. Compared with previous protocols, the new protocol minimizes the cost of computation with no extra message exchange time. In addition, the proposed protocol provides known key security, no key control, no key-compromise impersonation and perfect forward secrecy.

  17. Forensic Identification Based on Tooth Material

    OpenAIRE

    Elza Ibrahim Auerkari; Archinantinigsih Surjadi

    2015-01-01

    Human teeth are the most robust and stable parts of the body, providing biological clue material for forensic purposes even when most of the oter means of identifcation have been seriously affected by adverse environmental conditions. In particular blood grouping, isozymes, serum proteins and DNA polymorhphisms can be detected from teeth that protect these identification markers in addition to the traditional dental records. While in general the value of traditional dental records in the fore...

  18. Reinforcement of Conducting Silver-based Materials

    Directory of Open Access Journals (Sweden)

    Heike JUNG

    2014-09-01

    Full Text Available Silver is a well-known material in the field of contact materials because of its high electrical and thermal conductivity. However, due to its bad mechanical and switching properties, silver alloys or reinforcements of the ductile silver matrix are required. Different reinforcements, e. g. tungsten, tungsten carbide, nickel, cadmium oxide or tin oxide, are used in different sectors of switches. To reach an optimal distribution of these reinforcements, various manufacturing techniques (e. g. powder blending, preform infiltration, wet-chemical methods, internal oxidation are being used for the production of these contact materials. Each of these manufacturing routes offers different advantages and disadvantages. The mechanical alloying process displays a successful and efficient method to produce particle-reinforced metal-matrix composite powders. This contribution presents the obtained fine disperse microstructure of tungsten-particle-reinforced silver composite powders produced by the mechanical alloying process and displays this technique as possible route to provide feedstock powders for subsequent consolidation processes. DOI: http://dx.doi.org/10.5755/j01.ms.20.3.4889

  19. Regional cooperation and performance-based planning and programming in Indiana : a regional models of cooperation peer exchange summary report

    Science.gov (United States)

    2016-05-01

    This report highlights key themes identified at the Regional Cooperation and Performance-Based Planning and Programming in Indiana Peer Exchange held on May 25, 2016 in Indianapolis, Indiana. The Regional Models of Cooperation Initiative, which...

  20. The Multifunctional Fish Gill: Dominant Site of Gas Exchange, Osmoregulation, Acid-Base Regulation, and Excretion of Nitrogenous Waste

    National Research Council Canada - National Science Library

    David H. Evans; Peter M. Piermarini; Keith P. Choe

    2005-01-01

    The fish gill is a multipurpose organ that, in addition to providing for aquatic gas exchange, plays dominant roles in osmotic and ionic regulation, acid-base regulation, and excretion of nitrogenous wastes...

  1. Developing bulk exchange spring magnets

    Energy Technology Data Exchange (ETDEWEB)

    Mccall, Scott K.; Kuntz, Joshua D.

    2017-06-27

    A method of making a bulk exchange spring magnet by providing a magnetically soft material, providing a hard magnetic material, and producing a composite of said magnetically soft material and said hard magnetic material to make the bulk exchange spring magnet. The step of producing a composite of magnetically soft material and hard magnetic material is accomplished by electrophoretic deposition of the magnetically soft material and the hard magnetic material to make the bulk exchange spring magnet.

  2. Cation-exchanged SAPO-34 for adsorption-based hydrocarbon separations: predictions from dispersion-corrected DFT calculations.

    Science.gov (United States)

    Fischer, Michael; Bell, Robert G

    2014-10-21

    The influence of the nature of the cation on the interaction of the silicoaluminophosphate SAPO-34 with small hydrocarbons (ethane, ethylene, acetylene, propane, propylene) is investigated using periodic density-functional theory calculations including a semi-empirical dispersion correction (DFT-D). Initial calculations are used to evaluate which of the guest-accessible cation sites in the chabazite-type structure is energetically preferred for a set of ten cations, which comprises four alkali metals (Li(+), Na(+), K(+), Rb(+)), three alkaline earth metals (Mg(2+), Ca(2+), Sr(2+)), and three transition metals (Cu(+), Ag(+), Fe(2+)). All eight cations that are likely to be found at the SII site (centre of a six-ring) are then included in the following investigation, which studies the interaction with the hydrocarbon guest molecules. In addition to the interaction energies, some trends and peculiarities regarding the adsorption geometries are analysed, and electron density difference plots obtained from the calculations are used to gain insights into the dominant interaction types. In addition to dispersion interactions, electrostatic and polarisation effects dominate for the main group cations, whereas significant orbital interactions are observed for unsaturated hydrocarbons interacting with transition metal (TM) cations. The differences between the interaction energies obtained for pairs of hydrocarbons of interest (such as ethylene-ethane and propylene-propane) deliver some qualitative insights: if this energy difference is large, it can be expected that the material will exhibit a high selectivity in the adsorption-based separation of alkene-alkane mixtures, which constitutes a problem of considerable industrial relevance. While the calculations show that TM-exchanged SAPO-34 materials are likely to exhibit a very high preference for alkenes over alkanes, the strong interaction may render an application in industrial processes impractical due to the large amount

  3. The elution of metal cyanocomplexes from polyacrylic - and polystyrene- based ion exchange resins using nitrate and thiocyanate eluants

    OpenAIRE

    Riani,J. C.; Leão,V. A.; Silva, C.A.; Silva, A M; S. M. Bertolino; Lukey,G. C.

    2007-01-01

    Ion exchange resins can potentially be applied in cyanide recycling to address growing environmental concerns over the use of cyanide during gold extraction. In the present work the elution of copper-, iron-, and zinc-cyanocomplexes from polyacrylic- and polystyrene-based resins was studied. It was found that iron and copper cyanides are easily eluted from polyacrylic- and polystyrene-based ion exchange resins using either SCN- or NO3-. However, elution of the zinc cyanide complex from polyst...

  4. Armor Design Based on Material Properties,

    Science.gov (United States)

    1980-06-01

    and (C)E cosei/(l+F). (14) As indicated in §IIl, cracks nucleate in RHA at inclusions and grow in the weak bands of the microstructure, but the MnS...inclu- sions are concentrated in the weak bands . This leads to the coales- cence of major coplanar cracks after growth dependent on the inclusion...material comes apart. The approach taken here was to selectively treat the damage of the weak bands of the banded micro- structure, which is where

  5. Studies on PVA based nanocomposite Proton Exchange Membrane for Direct methanol fuel cell (DMFC) applications

    Science.gov (United States)

    Bahavan Palani, P.; Kannan, R.; Rajashabala, S.; Rajendran, S.; Velraj, G.

    2015-02-01

    Different concentrations of Poly (vinyl alcohol)/Montmorillonite (PVA/MMT) based proton exchange membranes (PEMs) have been prepared by solution casting method. The structural and electrical properties of these composite membranes have been characterized by using X-ray diffraction (XRD), Fourier transform infrared spectroscopic (FTIR) and AC impedance spectroscopic methods. The conductivity of the PEMs has been estimated for the different concentration of MMT. Water/Methanol uptake measurement were also analyzed for the prepared PEMs and presented. The proton conductivity studies were carried out at room temperature with 100% of humidity.

  6. Ion-Exchange Membranes Based on Polynorbornenes with Fluorinated Imide Side Chain Groups

    Directory of Open Access Journals (Sweden)

    Arlette A. Santiago

    2012-01-01

    Full Text Available The electrochemical characteristics of cation-exchange membranes based on polynorbornenes with fluorinated and sulfonated dicarboximide side chain groups were reported. This study was extended to a block copolymer containing structural units with phenyl and 4-oxybenzenesulfonic acid, 2,3,5,6-tetrafluorophenyl moieties replacing the hydrogen atom of the dicarboximide group. A thorough study on the electrochemical characteristics of the membranes involving electromotive forces of concentration cells and proton conductivity is reported. The proton permselectivity of the membranes is also discussed.

  7. The effect of different oxygen exchange layers on TaO x based RRAM devices

    Science.gov (United States)

    Alamgir, Zahiruddin; Holt, Joshua; Beckmann, Karsten; Cady, Nathaniel C.

    2018-01-01

    In this work, we investigated the effect of the oxygen exchange layer (OEL) on the resistive switching properties of TaO x based memory cells. It was found that the forming voltage, SET-RESET voltage, R off, R on and retention properties are strongly correlated with the oxygen scavenging ability of the OEL, and the resulting oxygen vacancy formation ability of this layer. Higher forming voltage was observed for OELs having lower electronegativity/lower Gibbs free energy for oxide formation, and devices fabricated with these OELs exhibited an increased memory window, when using similar SET-RESET voltage range.

  8. Selective anion exchange and tunable luminescent behaviors of metal-organic framework based supramolecular isomers.

    Science.gov (United States)

    Manna, Biplab; Singh, Shweta; Karmakar, Avishek; Desai, Aamod V; Ghosh, Sujit K

    2015-01-05

    Owing to the conformational (cis or trans) flexibility of a N-donor ligand, the combinations of the same and Cd(ClO4)2 under variable solvent templates afforded two supramolecular isomers based on two-dimensional metal-organic frameworks. Both compounds contain weakly coordinating ClO4(-) anions attached to the metal centers. Both frameworks showed facile anion exchange behaviors with various kinds of foreign anions. Moreover, both frameworks showed anion-driven structural dynamism and exhibited the preferential uptake of strongly coordinating anions over others. Anion-regulated modulation in luminescent behaviors was also observed in both cases.

  9. Nanosynthesis of Iron Based Material for Green Energy

    Science.gov (United States)

    Kirkeminde, Alec W.

    In this work, nanosynthesis of multiple iron-based materials are explored to further their use in green renewable-energy applications. First, the nanosynthesis of the abundant, non-toxic semi-conductor Iron Disulfide (Iron Pyrite, Fool's Gold, FeS2) is investigated. Within these studies, it became possible to tune the shape of the FeS2 nanoparticles easily by modifying injection temperatures and iron precursors. From here, the growth mechanisms of the different shapes were elucidated by examining different time points within the synthesis. It was discovered that the FeS2 did not grow by Ostwald Ripening, but instead by Oriented Attachment. Knowing this, it was possible to not only further the shapes of FeS2 nanoparticles, but also manipulate the size and crystallinity. Focus was then shifted to creating larger micron sized FeS2 crystals. Larger crystals where achieved by a unique FeS nanowire precursor followed by sulfurization. The dominant crystal surface of these crystals could be regulated simply by the time and temperature of the sulfurization. Second, synthetic control of magnetic nanoparticles was examined. A novel synthesis of Iron Palladium (FePd) made possible by interdiffusion of iron into palladium nanocores was identified. Furthermore, a shell of Iron oxide (Fe2O3) could facilely be grown on the FePd nanoparticles, generating a FePd/Fe2O3 core/shell nanoparticle. These FePd/Fe2O3 core/shell particles provided an excellent foundation to create an L10- FePd/α-Fe exchange-coupled nanocomposite that exhibited improved magnetic properties compared to its single phase FePd counterpart. However, the stabilizing ligand used within this FePd synthesis doped into the final nanoparticles, degraded the magnetic properties. iii To overcome the dopant ligand problem, a novel nanoalloy synthetic strategy of Metal Redox was developed. The Metal Redox strategy utilized the inherent reducing power of zero-valent metal sources to create a vast sampling of metal

  10. Biomedical applications of the graphene-based materials.

    Science.gov (United States)

    Zhang, Baomei; Wang, Yang; Zhai, Guangxi

    2016-04-01

    Graphene, a rapidly rising star, has gained extensive research interests lately due to its excellent properties--such as the exceptional optical, electrical, thermal and mechanical features--which are superior to other materials, so it is called "two-dimensional magical materials". This article presents diverse types and various properties of graphene-based materials, and the current methods for the surface modifications of the graphene-based materials are briefly described. In addition, the in vivo and in vitro cytotoxicity of graphene-based materials are comprehensively discussed. What's more, a summary of its biomedical applications such as drug/gene delivery, photothermal therapy, photodynamic therapy and multimodality therapy is also offered. Finally, an outlook of the graphene-based materials and the challenges in this field are briefly discussed. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Titanium microgram weight low to 50 mg and measurement based on exchange weighing method

    Science.gov (United States)

    Ren, Xiaoping; Dong, Lei; Wang, Jian; Wang, Xiaolei

    2017-03-01

    The microgram weights have wide applications in the mechanical testing of nano- and bio-material sensors. They are increasing the requirement of small force and mass below 1 mg among the researchers, industry and bio-pharmaceutical manufacturing. In this paper, the current research status is presented, both from the measurement method and manufacture of microgram weights. The commonly used material for micro-weights is stainless steel and aluminum. Now NIM has developed another kind of microgram weights with titanium alloy. For the reason that it has smaller size than normal material like aluminum, special designed exchange weighing pan was used in measurement, which solved the problems that the weighing hooks cannot carry up and down the wire shape microgram weight. Then this kind of microgram weights was tested in subdivision measurement on an automatic mass comparator. It showed good performance in the experiment, which extends the choice for the industrial and metrological user. The uncertainty evaluation of micro-weight values range from 0.05 mg to 0.5 mg with standard uncertainty between 0.2 g and 0.1 μg.

  12. Determination of Specific Heat Capacity on Composite Shape-Stabilized Phase Change Materials and Asphalt Mixtures by Heat Exchange System.

    Science.gov (United States)

    Ma, Biao; Zhou, Xue-Yan; Liu, Jiang; You, Zhanping; Wei, Kun; Huang, Xiao-Feng

    2016-05-19

    Previous research has shown that composite shape-stabilized phase change material (CPCM) has a remarkable capacity for thermal storage and stabilization, and it can be directly applied to highway construction without leakage. However, recent studies on temperature changing behaviors of CPCM and asphalt mixture cannot intuitively reflect the thermoregulation mechanism and efficiency of CPCM on asphalt mixture. The objective of this paper is to determine the specific heat capacity of CPCM and asphalt mixtures mixed with CPCM using the heat exchange system and the data acquisition system. Studies have shown that the temperature-rise curve of 5 °C CPCM has an obvious temperature plateau, while an asphalt mixture mixed with 5 °C CPCM does not; with increasing temperature, the specific heat capacities of both 5 °C CPCM and asphalt mixture first increase and then decrease, while the variation rate of 5 °C CPCM is larger than that of the asphalt mixture, and the maximum specific heat capacity of 5 °C CPCM appears around the initial phase change temperature. It is concluded that the temperature intervals of 5 °C CPCM are -18 °C-7 °C, 7 °C-25 °C and 25 °C-44 °C, respectively, and that of the asphalt mixture are -18 °C~10 °C, -10 °C~5 °C and 5 °C~28 °C. A low dosage of 5 °C CPCM has little influence on the specific heat capacity of asphalt mixture. Finally, the functions of specific heat capacities and temperature for CPCM and asphalt mixture mixed with CPCM were recommended by the sectional regression method.

  13. A Project to Design and Build Compact Heat Exchangers

    Science.gov (United States)

    Davis, Richard A.

    2005-01-01

    Students designed and manufactured compact, shell-and-tube heat exchangers in a project-based learning exercise integrated with our heat transfer course. The heat exchangers were constructed from common building materials available at home improvement centers. The cost of materials for a device was less than $20. The project gave students…

  14. Slow light based on material and waveguide dispersion

    DEFF Research Database (Denmark)

    Nielsen, Torben Roland; Lavrinenko, Andrei; Mørk, Jesper

    2009-01-01

    We study slow light pulse propagation in a photonic crystal structure consisting of a dispersive and absorptive dielectric material and compare it with the constant wave case. The group index and the trasmission are investigated for the example of an ensemble of semiconductor quantum dots embedde...... in a photonic crystal waveguide by FDTD Maxwell-Bloch simulations. The total group index scales linearly with the material based group index whicle the transmission has a power dependency on the material based absorption coefficient....

  15. Densified ultra-light cement-based materials

    DEFF Research Database (Denmark)

    Esteves, Luis Pedro

    2015-01-01

    be used as a “clean technology” in the production of cement-based materials for structural applications with a low carbon footprint. This paper describes the principles of this concept coupled with experimental results on the basic properties of this enhanced type of cement-based materials with combined...

  16. An Integrated, Problem-Based Learning Material: The "Satellite" Module

    Science.gov (United States)

    Selcuk, Gamze Sezgin; Emiroglu, Handan Byacioglu; Tarakci, Mehmet; Ozel, Mustafa

    2011-01-01

    The purpose of this study is to introduce a problem-based learning material, the Satellite Module, that has integrated some of the subjects included in the disciplines of physics and mathematics at an introductory level in undergraduate education. The reason why this modular and problem-based material has been developed is to enable students to…

  17. Development of bio-hybrid material based on Salmonella ...

    African Journals Online (AJOL)

    The immobilization of a whole microbial cell is an important process used in nanotechnology of biosensors and other related fields, especially the development of bio-hybrid materials based on live organisms and inorganic compounds. Here, we described an essay to develop a bio-hybrid material based on Salmonella ...

  18. Advanced luminescent materials based on organoboron polymers.

    Science.gov (United States)

    Tanaka, Kazuo; Chujo, Yoshiki

    2012-08-14

    Our work on the characteristics of organoboron-containing polymers is reviewed. The electronic interaction and correlation involving organoboron complexes are responsible for the optical and electric properties of the polymers. To understand the origins of these properties and apply them to the next generation of new materials, we have gathered not only fundamental knowledge on the electronic states and behaviors of each organoboron complex in the polymers but also on the functions of the polymers in devices. In this article, we introduce our findings obtained from a series of studies on polymers involving cyclodiborazane, quinolate, diketonate, dipyrromethene, pyrazabole, and carborane complexes. In particular, there is a focus on results from recent work. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Joint research and development and exchange of technology on toxic material emergency response between LLNL and ENEA. 1985 progress report

    Energy Technology Data Exchange (ETDEWEB)

    Dickerson, M.H.; Caracciolo, R.

    1986-01-31

    For the past six years, the US Department of Energy, LLNL, and the ENEA, Rome, Italy, have participated in cooperative studies for improving a systems approach to an emergency response following nuclear accidents. Technology exchange between LLNL and the ENEA was initially confined to the development, application, and evaluation of atmospheric transport and diffusion models. With the emergence of compatible hardware configurations between LLNL and ENEA, exchanges of technology and ideas for improving the development and implementation of systems are beginning to emerge. This report describes cooperative work that has occurred during the past three years, the present state of each system, and recommendations for future exchanges of technology.

  20. Preparation of a monolithic cation-exchange material with hydrophilic external layers by two-step reversible addition-fragmentation chain transfer polymerization.

    Science.gov (United States)

    Lin, Shen; Zhang, Yingying; Huang, Wei; Dong, Xiangchao

    2017-04-01

    In recent years, the efficient analysis of biological samples has become more important due to the advances of life science and pharmaceutical research and practice. Because biological sample pretreatment is the bottleneck for fast process, material development for efficient sample process in the high-performance liquid chromatography analysis is highly desirable. In this research, a cation-exchange restricted access monolithic column was synthesized by a reversible addition-fragmentation chain transfer polymerization method. Utilizing the controlled/living property of the reversible addition-fragmentation chain transfer method, a monolithic column of cross-linked poly(sulfopropyl methacrylate) was prepared first and then linear poly(glycerol mono-methacrylate) was immobilized covalently on the surface of the polymer. The monolithic material has both functionalities of cation-exchange and protein exclusion. Protein recovery of 94.6% was obtained after grafting of poly(glycerol mono-methacrylate) while the cation-exchange property of the column is still retained. In the study, the relation between the synthetic conditions and properties of the materials was studied. The synthesis conditions including the porogen, monomer concentration, and ratio of monomers/initiator/reversible addition-fragmentation chain transfer agent were optimized. The study provided a method for the preparation of restricted access monolithic columns: a bifunctional material by reversible addition-fragmentation chain transfer polymerization method. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Factors affecting spatial and temporal variability in material exchange between the Southern Everglades wetlands and Florida Bay (USA)

    Science.gov (United States)

    Sutula, Martha A.; Perez, Brian C.; Reyes, Enrique; Childers, Daniel L.; Davis, Steve; Day, John W.; Rudnick, David; Sklar, Fred

    2003-08-01

    Physical and biological processes controlling spatial and temporal variations in material concentration and exchange between the Southern Everglades wetlands and Florida Bay were studied for 2.5 years in three of the five major creek systems draining the watershed. Daily total nitrogen (TN), and total phosphorus (TP) fluxes were measured for 2 years in Taylor River, and ten 10-day intensive studies were conducted in this creek to estimate the seasonal flux of dissolved inorganic nitrogen (N), phosphorus (P), total organic carbon (TOC), and suspended matter. Four 10-day studies were conducted simultaneously in Taylor, McCormick, and Trout Creeks to study the spatial variation in concentration and flux. The annual fluxes of TOC, TN, and TP from the Southern Everglades were estimated from regression equations. The Southern Everglades watershed, a 460-km 2 area that includes Taylor Slough and the area south of the C-111 canal, exported 7.1 g C m -2, 0.46 g N m -2, and 0.007 g P m -2, annually. Everglades P flux is three to four orders of magnitude lower than published flux estimates from wetlands influenced by terrigenous sedimentary inputs. These low P flux values reflect both the inherently low P content of Everglades surface water and the efficiency of Everglades carbonate sediments and biota in conserving and recycling this limiting nutrient. The seasonal variation of freshwater input to the watershed was responsible for major temporal variations in N, P, and C export to Florida Bay; approximately 99% of the export occurred during the rainy season. Wind-driven forcing was most important during the later stages of the dry season when low freshwater head coincided with southerly winds, resulting in a net import of water and materials into the wetlands. We also observed an east to west decrease in TN:TP ratio from 212:1 to 127:1. Major spatial gradients in N:P ratios and nutrient concentration and flux among the creek were consistent with the westward decrease in

  2. Cleaning power and abrasivity of a new toothpaste based on ion-exchange resins.

    Science.gov (United States)

    Torrado, Anna; Valiente, Manuel; Muñoz, Carlos A

    2004-04-01

    To compare the stain removal efficacy and enamel abrasivity of a new experimental dentifrice based on an ion-exchange resin mixture that releases calcium, fluoride, phosphate and zinc ions (named NMTD1), to four commercially available dentifrices: Crest Extra-whitening toothpaste, Crest Tartar Protection toothpaste, Crest Cavity Protection toothpaste and Colgate Fluoride Cavity Protection toothpaste. Calcium pyrophosphate was used as a control for the efficacy of the staining removal experiment. Cleaning power evaluation was made following the method developed by Stookey et al. The abrasion of the toothpastes was determined by means of a brushing machine, using 2000, 4000 and 8000 strokes and a 250g toothbrush load. Bovine specimens were prepared and abrasion was measured by a surface profilometer system. The new experimental dentifrice did not remove stains whereas Crest Extra-whitening and Crest Cavity Protection dentifrices produced statistically significant stain removal when compared with the calcium pyrophosphate control. Abrasion studies demonstrated that abrasion was linearly correlated to the number of strokes and the abrasion rates proved to be non significant for Colgate and the new experimental dentifrices, but significant for Crest Extra-whitening, Crest Tartar Protection and Crest Cavity Protection. This study demonstrated that the use of a dentifrice based on an ion-exchange mixture was not effective at removing stains and abrasion was most insignificant when compared to other commercially available toothpastes.

  3. Network Analysis of the Shanghai Stock Exchange Based on Partial Mutual Information

    Directory of Open Access Journals (Sweden)

    Tao You

    2015-06-01

    Full Text Available Analyzing social systems, particularly financial markets, using a complex network approach has become one of the most popular fields within econophysics. A similar trend is currently appearing within the econometrics and finance communities, as well. In this study, we present a state-of-the-artmethod for analyzing the structure and risk within stockmarkets, treating them as complex networks using model-free, nonlinear dependency measures based on information theory. This study is the first network analysis of the stockmarket in Shanghai using a nonlinear network methodology. Further, it is often assumed that markets outside the United States and Western Europe are inherently riskier. We find that the Chinese stock market is not structurally risky, contradicting this popular opinion. We use partial mutual information to create filtered networks representing the Shanghai stock exchange, comparing them to networks based on Pearson’s correlation. Consequently, we discuss the structure and characteristics of both the presented methods and the Shanghai stock exchange. This paper provides an insight into the cutting edge methodology designed for analyzing complex financial networks, as well as analyzing the structure of the market in Shanghai and, as such, is of interest to both researchers and financial analysts.

  4. Momentum exchange in multiphase dispersed flow: a statistical estimator based on multilevel Monte Carlo

    Science.gov (United States)

    Icardi, Matteo

    2014-11-01

    Eulerian-Eulerian models for multiphase dispersed flow are commonly derived by means of ensemble (or spatial) averaging. They are therefore based on quantities defined over statistical (or spatial) ensemble of particle configurations. However momentum exchange correlations (e.g., drag, lift) are known (and can be defined deterministically) only for the dilute (isolated spheres) and dense (Ergun) limits. Furthermore it is well known that the overall results are often very sensitive to the correlation chosen and to the closure approximations for fluctuations, strongly limiting the predictive capability of the models. In this work the forces acting on random array of spheres and other granular objects have been studied with a novel statistical approach based on multilevel Monte Carlo. Direct Numerical Simulations are used to resolve the flow around the spheres and both the numerical and statistical error are controlled accurately. Mean and fluctuations of the momentum exchange terms can be characterized to derive new correlations for drag and lift in dense poly-dispersed flows that are statistically robust.

  5. Surface characterization of graphene based materials

    Science.gov (United States)

    Pisarek, M.; Holdynski, M.; Krawczyk, M.; Nowakowski, R.; Roguska, A.; Malolepszy, A.; Stobinski, L.; Jablonski, A.

    2016-12-01

    In the present study, two kind of samples were used: (i) a monolayer graphene film with a thickness of 0.345 nm deposited by the CVD method on Cu foil, (ii) graphene flakes obtained by modified Hummers method and followed by reduction of graphene oxide. The inelastic mean free path (IMFP), characterizing electron transport in graphene/Cu sample and reduced graphene oxide material, which determines the sampling depth of XPS and AES were evaluated from relative Elastic Peak Electron Spectroscopy (EPES) measurements with the Au standard in the energy range 0.5-2 keV. The measured IMFPs were compared with IMFPs resulting from experimental optical data published in the literature for the graphite sample. The EPES IMFP values at 0.5 and 1.5 keV was practically identical to that calculated from optical data for graphite (less than 4% deviation). For energies 1 and 2 keV, the EPES IMFPs for rGO were deviated up to 14% from IMFPs calculated using the optical data by Tanuma et al. [1]. Before EPES measurements all samples were characterized by various techniques like: FE-SEM, AFM, XPS, AES and REELS to visualize the surface morphology/topography and identify the chemical composition.

  6. Characterization of electrical and optical properties of silicon based materials

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Guobin

    2009-12-04

    In this work, the electrical and luminescence properties of a series of silicon based materials used for photovoltaics, microelectronics and nanoelectronics have been investigated by means of electron beam induced current (EBIC), cathodoluminescence (CL), photoluminescence (PL) and electroluminescence (EL) methods. Photovoltaic materials produced by block casting have been investigated by EBIC on wafers sliced from different parts of the ingot. Various solar cell processings have been compared in parallel wafers by means of EBIC collection efficiency measurements and contrast-temperature C(T) behaviors of the extended defects, i. e. dislocations and grain boundaries (GBs). It was found that the solar cell processing with phosphorus diffusion gettering (PDG) followed with a SiN firing greatly reduces the recombination activity of extended defects at room temperature, and improves the bulk property simultaneously. A remaining activity of the dislocations indicates the limitation of the PDG at extended defects. Abnormal behavior of the dislocation activity after certain solar cell processes was also observed in the region with high dislocation density, the dislocations are activated after certain solar cell processings. In order to evaluate the properties of a thin polycrystalline silicon layer prepared by Al-induced layer exchange (Alile) technique, epitaxially layer grown on silicon substrate with different orientations was used as a model system to investigate the impact by the process temperature and the substrates. EBIC energy dependent collection efficiency measurements reveal an improvement of the epilayer quality with increasing substrate temperature during the growth from 450 C to 650 C, and a decrease of epilayer quality at 700 C. PL measurements on the epitaxially grown Si layer on silicon substrates revealed no characteristic dislocation-related luminescence (DRL) lines at room temperature and 77 K, while in the samples prepared by Alile process, intense

  7. The effect of Sinabung volcanic ash and rock phosphate nanoparticle on CEC (cation exchange capacity) base saturation exchange (K, Na, Ca, Mg) and base saturation at Andisol soils Ciater, West Java

    Science.gov (United States)

    Yuniarti, Anni; Arifin, Mahfud; Sofyan, Emma Trinurasi; Natalie, Betty; Sudirja, Rija; Dahliani, Dewi

    2018-02-01

    Andisol, soil orders which covers an upland area dominantly. The aim of this research is to know the effect between the ameliorant of Sinabung volcanic ashes with the ameliorant of rock phosphatenanoparticle towards CEC and base saturation exchange (K, Na, Ca, Mg) and the base saturation on Ciater's Andisols, West Java. A randomized complete block design (RCBD) factorial with two factors was used in this research. The first factor is the volcanic ash and the second factor is rock phosphate which consists of four levels each amount of 0%, 2.5%, 5%, 7.5% with three replications. The result showed that there was no interaction between volcanic ash and rock phosphate nanoparticle formed in first month and fourth month towards the improvement of CEC and saturation base exchange rate unless magnesium cation exchange increased in fourth month. There was independent effect of volcanic ash formed nanoparticles towards base saturation exchange increased for 5% dose. There was independent effect of rock phosphate formed nanoparticles towards base saturation exchange and increased for 5% dose. The dose combination of volcanic ashes 7.5% with phosphate rock, 5% increased the base saturation in the first month incubation.

  8. Modelling of the interaction between chemical and mechanical behaviour of ion exchange resins incorporated into a cement-based matrix

    Directory of Open Access Journals (Sweden)

    Le Bescop P.

    2013-07-01

    Full Text Available In this paper, we present a predictive model, based on experimental data, to determine the macroscopic mechanical behavior of a material made up of ion exchange resins solidified into a CEM III cement paste. Some observations have shown that in some cases, a significant macroscopic expansion of this composite material may be expected, due to internal pressures generated in the resin. To build the model, we made the choice to break down the problem in two scale’s studies. The first deals with the mechanical behavior of the different heterogeneities of the composite, i.e. the resin and the cement paste. The second upscales the information from the heterogeneities to the Representative Elementary Volume (REV of the composite. The heterogeneities effects are taken into account in the REV by applying a homogenization method derived from the Eshelby theory combined with an interaction coefficient drawn from the poroelasticity theory. At the first scale, from the second thermodynamic law, a formulation is developed to estimate the resin microscopic swelling. The model response is illustrated on a simple example showing the impact of the calculated internal pressure, on the macroscopic strain.

  9. Passive Sensor Materials Based on Liquid Crystals

    Science.gov (United States)

    2011-03-12

    Seminar, Chemical Engineering,,Virginia Tech, October, 2008. Abbott, N.L. “Biomolecular Analysis based on Liquid Crystals”, Innovative Molecular Analysis ...of Liquid Crystals" Columbia University, February, 2010, "Novel Colloidal and Interfacial Phenomena in Liquid Crystalline Systems" CBD Conference...extended to other oils (silicone oil and paraffin oil droplets) and the size of capsule templates was also varied (0.7 to 10 μm, Figure 15) to

  10. Emerging Ceramic-based Materials for Dentistry

    Science.gov (United States)

    Denry, I.; Kelly, J.R.

    2014-01-01

    Our goal is to give an overview of a selection of emerging ceramics and issues for dental or biomedical applications, with emphasis on specific challenges associated with full-contour zirconia ceramics, and a brief synopsis on new machinable glass-ceramics and ceramic-based interpenetrating phase composites. Selected fabrication techniques relevant to dental or biomedical applications such as microwave sintering, spark plasma sintering, and additive manufacturing are also reviewed. Where appropriate, the authors have added their opinions and guidance. PMID:25274751

  11. Directly patching high-level exchange-correlation potential based on fully determined optimized effective potentials.

    Science.gov (United States)

    Huang, Chen; Chi, Yu-Chieh

    2017-12-28

    The key element in Kohn-Sham (KS) density functional theory is the exchange-correlation (XC) potential. We recently proposed the exchange-correlation potential patching (XCPP) method with the aim of directly constructing high-level XC potential in a large system by patching the locally computed, high-level XC potentials throughout the system. In this work, we investigate the patching of the exact exchange (EXX) and the random phase approximation (RPA) correlation potentials. A major challenge of XCPP is that a cluster's XC potential, obtained by solving the optimized effective potential equation, is only determined up to an unknown constant. Without fully determining the clusters' XC potentials, the patched system's XC potential is "uneven" in the real space and may cause non-physical results. Here, we developed a simple method to determine this unknown constant. The performance of XCPP-RPA is investigated on three one-dimensional systems: H20, H10Li8, and the stretching of the H19-H bond. We investigated two definitions of EXX: (i) the definition based on the adiabatic connection and fluctuation dissipation theorem (ACFDT) and (ii) the Hartree-Fock (HF) definition. With ACFDT-type EXX, effective error cancellations were observed between the patched EXX and the patched RPA correlation potentials. Such error cancellations were absent for the HF-type EXX, which was attributed to the fact that for systems with fractional occupation numbers, the integral of the HF-type EXX hole is not -1. The KS spectra and band gaps from XCPP agree reasonably well with the benchmarks as we make the clusters large.

  12. Directly patching high-level exchange-correlation potential based on fully determined optimized effective potentials

    Science.gov (United States)

    Huang, Chen; Chi, Yu-Chieh

    2017-12-01

    The key element in Kohn-Sham (KS) density functional theory is the exchange-correlation (XC) potential. We recently proposed the exchange-correlation potential patching (XCPP) method with the aim of directly constructing high-level XC potential in a large system by patching the locally computed, high-level XC potentials throughout the system. In this work, we investigate the patching of the exact exchange (EXX) and the random phase approximation (RPA) correlation potentials. A major challenge of XCPP is that a cluster's XC potential, obtained by solving the optimized effective potential equation, is only determined up to an unknown constant. Without fully determining the clusters' XC potentials, the patched system's XC potential is "uneven" in the real space and may cause non-physical results. Here, we developed a simple method to determine this unknown constant. The performance of XCPP-RPA is investigated on three one-dimensional systems: H20, H10Li8, and the stretching of the H19-H bond. We investigated two definitions of EXX: (i) the definition based on the adiabatic connection and fluctuation dissipation theorem (ACFDT) and (ii) the Hartree-Fock (HF) definition. With ACFDT-type EXX, effective error cancellations were observed between the patched EXX and the patched RPA correlation potentials. Such error cancellations were absent for the HF-type EXX, which was attributed to the fact that for systems with fractional occupation numbers, the integral of the HF-type EXX hole is not -1. The KS spectra and band gaps from XCPP agree reasonably well with the benchmarks as we make the clusters large.

  13. Surface characterization and functional properties of carbon-based materials

    OpenAIRE

    2012-01-01

    Carbon-based materials are poised to be an important class of 21st century materials, for bio-medical, bio-electronic, and bio-sensing applications. Diamond and polymers are two examples of carbon-based materials of high interest to the bio-materials community. Diamond, in its conductive form, can be used as an electrochemical bio-sensor, whilst its nanoparticle form is considered a non-inflammatory platform to deliver drugs or to grow neuronal cells. Polymers, especially when chemically m...

  14. Emerging ceramic-based materials for dentistry.

    Science.gov (United States)

    Denry, I; Kelly, J R

    2014-12-01

    Our goal is to give an overview of a selection of emerging ceramics and issues for dental or biomedical applications, with emphasis on specific challenges associated with full-contour zirconia ceramics, and a brief synopsis on new machinable glass-ceramics and ceramic-based interpenetrating phase composites. Selected fabrication techniques relevant to dental or biomedical applications such as microwave sintering, spark plasma sintering, and additive manufacturing are also reviewed. Where appropriate, the authors have added their opinions and guidance. © International & American Associations for Dental Research.

  15. Autonomous quantum Maxwell's demon based on two exchange-coupled quantum dots

    Science.gov (United States)

    Ptaszyński, Krzysztof

    2018-01-01

    I study an autonomous quantum Maxwell's demon based on two exchange-coupled quantum dots attached to the spin-polarized leads. The principle of operation of the demon is based on the coherent oscillations between the spin states of the system which act as a quantum iSWAP gate. Due to the operation of the iSWAP gate, one of the dots acts as a feedback controller which blocks the transport with the bias in the other dot, thus inducing the electron pumping against the bias; this leads to the locally negative entropy production. Operation of the demon is associated with the information transfer between the dots, which is studied quantitatively by mapping the analyzed setup onto the thermodynamically equivalent auxiliary system. The calculated entropy production in a single subsystem and information flow between the subsystems are shown to obey a local form of the second law of thermodynamics, similar to the one previously derived for classical bipartite systems.

  16. Assessing the value of cooperation and information exchange in large water resources systems by agent-based optimization

    Science.gov (United States)

    Giuliani, M.; Castelletti, A.

    2013-07-01

    Many large-scale water resources systems, especially in transboundary contexts, are characterized by the presence of several and conflicting interests and managed by multiple, institutionally independent decision makers. These systems are often studied adopting a centralized approach based on the assumption of full cooperation and information exchange among the involved parties. Such a perspective is conceptually interesting to quantify the best achievable performance but might have little practical impact given the real political and institutional setting. In this work, we propose a novel decision-analytic framework based on multiagent systems to model and analyze different levels of cooperation and information exchange among multiple decision makers. The Zambezi River basin is used as a case study. According to the proposed agent-based optimization approach, each agent represents a decision maker, whose decisions are defined by an explicit optimization problem considering only the agent's local interests. The economic value of information exchange is estimated comparing a noncooperative setting, where agents act independently, with the first basic level of cooperation, i.e., coordination, characterized by full information exchange. The economic value of cooperation is also estimated by comparison with the ideal, fully cooperative management of the system. Results show that coordination, obtained with complete information exchange, allows the downstream agents to better adapt to the upstream behaviors. The impact of information exchange depends on the objective considered, and we show coordination to be particularly beneficial to environmental interests.

  17. Evaluating of arsenic(V) removal from water by weak-base anion exchange adsorbents.

    Science.gov (United States)

    Awual, M Rabiul; Hossain, M Amran; Shenashen, M A; Yaita, Tsuyoshi; Suzuki, Shinichi; Jyo, Akinori

    2013-01-01

    Arsenic contamination of groundwater has been called the largest mass poisoning calamity in human history and creates severe health problems. The effective adsorbents are imperative in response to the widespread removal of toxic arsenic exposure through drinking water. Evaluation of arsenic(V) removal from water by weak-base anion exchange adsorbents was studied in this paper, aiming at the determination of the effects of pH, competing anions, and feed flow rates to improvement on remediation. Two types of weak-base adsorbents were used to evaluate arsenic(V) removal efficiency both in batch and column approaches. Anion selectivity was determined by both adsorbents in batch method as equilibrium As(V) adsorption capacities. Column studies were performed in fixed-bed experiments using both adsorbent packed columns, and kinetic performance was dependent on the feed flow rate and competing anions. The weak-base adsorbents clarified that these are selective to arsenic(V) over competition of chloride, nitrate, and sulfate anions. The solution pH played an important role in arsenic(V) removal, and a higher pH can cause lower adsorption capacities. A low concentration level of arsenic(V) was also removed by these adsorbents even at a high flow rate of 250-350 h(-1). Adsorbed arsenic(V) was quantitatively eluted with 1 M HCl acid and regenerated into hydrochloride form simultaneously for the next adsorption operation after rinsing with water. The weak-base anion exchange adsorbents are to be an effective means to remove arsenic(V) from drinking water. The fast adsorption rate and the excellent adsorption capacity in the neutral pH range will render this removal technique attractive in practical use in chemical industry.

  18. Synthesis and characterization of inorganic ion exchangers based on mixed oxide tin-titanium to be used in recovery of cadmium and nickel and photoluminescent studies; Sintese e caracterizacao de trocadores ionicos inorganicos a base de oxidos mistos estanho-titanio para utilizacao na recuperacao de cadmio e niquel e estudos fotoluminescentes

    Energy Technology Data Exchange (ETDEWEB)

    Paganini, Paula Pinheiro

    2007-07-01

    This work presents the synthesis, characterization and adsorption studies of inorganic ion exchangers based on mixed tin-titanium oxide for recovery of cadmium and nickel metals from aqueous effluents, discarded in the environment mainly through Ni-Cd battery. The exchangers were synthesized by sol-gel modified method using a mixture of tin(IV) chloride and titanium(III) chloride and ammonium hydroxide, as precursors reagents. The materials obtained: SnO{sub 2}/TiO{sub 2} and SnO{sub 2}/TiO{sub 2}:Eu{sup 3+} were characterized by infrared spectroscopy, thermal analysis, scattering electronic microscopy (SEM), X-ray powder diffraction (XRD) (powder method) and electronic spectroscopy (excitation and emission) for the europium doped exchanger. The same materials also were synthesized in polymeric matrix too and can be used in column, because the synthesized materials showed crystals size in nano metric scale. It was determined by the distribution ratios for metals taking as parameters the influence of pH, the concentration of metals (by adsorption isotherms) and the contact time (by adsorption kinetic). The inorganic ion exchanger presented high exchange capacity with adsorption percent above 90 por cent for the studied conditions, quickly kinetic, heterogeneous exchange surfaces, physic adsorption and spontaneous process of exchange. To the doped exchanger spectroscopy properties were studied and also it was calculated the intensity parameters and it was found a satisfactory quantum yield. (author)

  19. Chemical exchange program analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Waffelaert, Pascale

    2007-09-01

    As part of its EMS, Sandia performs an annual environmental aspects/impacts analysis. The purpose of this analysis is to identify the environmental aspects associated with Sandia's activities, products, and services and the potential environmental impacts associated with those aspects. Division and environmental programs established objectives and targets based on the environmental aspects associated with their operations. In 2007 the most significant aspect identified was Hazardous Materials (Use and Storage). The objective for Hazardous Materials (Use and Storage) was to improve chemical handling, storage, and on-site movement of hazardous materials. One of the targets supporting this objective was to develop an effective chemical exchange program, making a business case for it in FY07, and fully implementing a comprehensive chemical exchange program in FY08. A Chemical Exchange Program (CEP) team was formed to implement this target. The team consists of representatives from the Chemical Information System (CIS), Pollution Prevention (P2), the HWMF, Procurement and the Environmental Management System (EMS). The CEP Team performed benchmarking and conducted a life-cycle analysis of the current management of chemicals at SNL/NM and compared it to Chemical Exchange alternatives. Those alternatives are as follows: (1) Revive the 'Virtual' Chemical Exchange Program; (2) Re-implement a 'Physical' Chemical Exchange Program using a Chemical Information System; and (3) Transition to a Chemical Management Services System. The analysis and benchmarking study shows that the present management of chemicals at SNL/NM is significantly disjointed and a life-cycle or 'Cradle-to-Grave' approach to chemical management is needed. This approach must consider the purchasing and maintenance costs as well as the cost of ultimate disposal of the chemicals and materials. A chemical exchange is needed as a mechanism to re-apply chemicals on site. This

  20. Monomer exchange and the hourglass model of protein-based oscillators

    Science.gov (United States)

    Emberly, Eldon

    2008-03-01

    Circadian rhythms in photosynthetic cyanobacteria are under the control of a three protein biochemical network that generates oscillations in the phosphorylation level of one of the proteins. This oscillatory signal has a period of roughly 24 hours and regulates many biological processes in the bacteria to the day and night cycle. The molecular view of the phosphorylation process is that one of the proteins forms a hexameric complex whose phosphorylation levels rise and fall based on the activity of the other two proteins. Each hexameric complex thus functions as an independent molecular clock. However the bacteria contains many such clocks and so how do they interact to generate a coherent oscillating signal? In this talk I will discuss a model that suggests that monomer exchange between hexamers helps to synchronize the population of clocks during the daylight portion of the oscillation. Other synchronizing mechanisms will be highlighted for the other portion of the cycle. Recent experiments will be discussed in light of the exchange model.

  1. Enantioseparations by high-performance liquid chromatography based on chiral ligand-exchange.

    Science.gov (United States)

    Natalini, Benedetto; Sardella, Roccaldo; Ianni, Federica

    2013-01-01

    Chiral ligand-exchange chromatography (CLEC) first described in the late 1960s to early 1970s by Davankov and Rogozhin can be still considered as an elective choice for the direct enantioseparation of compounds endowed with chelating moieties. Among the numerous chelating species that have been evaluated as chiral selectors in ligand-exchange (LE) chromatography, a special role is played by a group of amino acids including proline, hydroxyproline, cysteine, phenylalanine, and penicillamine. More to the point, relevant chromatographic performances are also provided by amino alcohol-based chiral selectors, among which, those carrying a leucinol residue as the basic scaffold are worth to be mentioned. Among the various enantiomer chromatographic separation techniques, CLEC has been exploited in all the main techniques including a chiral mobile phase (CMP), a covalently bound chiral stationary phase (B-CSP), and a coated chiral stationary phase (C-CSP). It is the objective of this chapter to describe selected CLEC applications dealing with the above three distinct approaches.

  2. A self-cleaning coating based on commercial grade polyacrylic latex modified by TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Nosrati, Rahimeh, E-mail: ra.nosrati@gmail.com [Polymer Composite Research Laboratory, Department of Applied Chemistry, Faculty of Chemistry, University of Tabriz, Tabriz (Iran, Islamic Republic of); Olad, Ali, E-mail: a.olad@yahoo.com [Polymer Composite Research Laboratory, Department of Applied Chemistry, Faculty of Chemistry, University of Tabriz, Tabriz (Iran, Islamic Republic of); Nofouzi, Katayoon, E-mail: nofouzi@tabrizu.ac.ir [Faculty of Veterinary Medicine, University of Tabriz, Tabriz (Iran, Islamic Republic of)

    2015-08-15

    Graphical abstract: - Highlights: • A novel nanocomposite coating based on polyacrylic was prepared. • Nanostructured TiO{sub 2}/Ag-exchanged-zeolite-A composite material was prepared. • Prepared nanocomposite used as additive for modification of polyacrylic latex. • Modified coatings show self-cleaning and antibacterial properties. • Modified coatings show better stability in water in versus of unmodified polymer. - Abstract: The commercial grade polyacrylic latex was modified in order to prepare a self-cleaning coating. TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite was prepared and used as additive in the matrix of polyacrylic latex to achieve a hydrophilic and photocatalytic coating. FTIR and UV–visible spectroscopy, X-ray diffraction patterns and FESEM were used to characterize the composition and structure of the nanocomposites and coatings. The acrylic coatings, were prepared by using of TiO{sub 2}/Ag-exchanged-zeolite-A additive, had better UV and visible light absorption, hydrophilic, degradation of organic pollutants, stability in water and antimicrobial properties than pristine commercial grade polyacrylic latex coating. According to the results, the modified polyacrylic based coating containing 0.5 wt% of TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite additive with TiO{sub 2} to Ag-exchanged-zeolite-A ratio of 1:2 was the best coating considering most of useful properties such as small band gap and low water contact angle. The water contact angle for unmodified polyacrylic latex coating was 68° which was decreased to less than 10° in modified coating after 24 h LED lamp illumination.

  3. Electron Charged Graphite-based Hydrogen Storage Material

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Chinbay Q. Fan; D Manager

    2012-03-14

    The electron-charge effects have been demonstrated to enhance hydrogen storage capacity using materials which have inherent hydrogen storage capacities. A charge control agent (CCA) or a charge transfer agent (CTA) was applied to the hydrogen storage material to reduce internal discharge between particles in a Sievert volumetric test device. GTI has tested the device under (1) electrostatic charge mode; (2) ultra-capacitor mode; and (3) metal-hydride mode. GTI has also analyzed the charge distribution on storage materials. The charge control agent and charge transfer agent are needed to prevent internal charge leaks so that the hydrogen atoms can stay on the storage material. GTI has analyzed the hydrogen fueling tank structure, which contains an air or liquid heat exchange framework. The cooling structure is needed for hydrogen fueling/releasing. We found that the cooling structure could be used as electron-charged electrodes, which will exhibit a very uniform charge distribution (because the cooling system needs to remove heat uniformly). Therefore, the electron-charge concept does not have any burden of cost and weight for the hydrogen storage tank system. The energy consumption for the electron-charge enhancement method is quite low or omitted for electrostatic mode and ultra-capacitor mode in comparison of other hydrogen storage methods; however, it could be high for the battery mode.

  4. PENERAPAN MODEL PEMBELAJARAN ROTATING TRIO EXCHANGE (RTE UNTUK MENINGKATKAN KUALITAS PEMBELAJARAN MATERI UPAYA-UPAYA PENEGAKAN HAM DI INDONESIA

    Directory of Open Access Journals (Sweden)

    Hasti Anggraini

    2017-03-01

    Full Text Available The purpose of this research is to improve the quality of learning through the application of the Rotating Trio Exchange (RTE model on the Material of Human Rights Enforcement in Indonesia. The study wasconducted in X IPA 4 and X IPA 8 graders of SMA Negeri 1 Pati Academic Year 2014 / 2015. The characteristic of students in both classes is balanced in terms of the dynamics of the activity and the value of learning outcomes that all have passed the learning mastery (100% passed.Implementation of the actions carried out in three cycles (cycle I, II, and III, each cycle lasts for 135 minutes (3 x 45 minutes. The design of Class Action Research uses the models of Kemmis and Taggart (1988 whose implementation consists of four steps: (1 planning; (2 implementation; (3 observation; and (4 reflection.The results of the implementation on the first cycle is not in line with expectations, as one indicator of the knowledge domains and one indicator of the skill domains shows a lower value or not balanced with other indicators. The average classical learning mastery in this cycle is above the passing grade (80. TQM indicators of these two classes is balanced, that is 684 for X IPA 4 and 679 for X IPA 8. The mean of TQM cognitive formation of both classes is 24.87%, skills is 49.081, and attitudes is 26.049%. In the second cycle, an improvement is carried out in the discourse of knowledge and skills of 7.8. This is influenced by the dynamics of student involvement equalization model which is evenly and alternately. In the third cycle, the two classes showed a different increase in quality, class X IPA 8 showed positive improvement, while Class X IPA 4 shows a fluctuative increase. The increase is relatively small, nevertheless indicates a significant RTE models to improve the quality of classical learning. The use of appropriate learning models is one of the factors that teachers can do to improve the quality of learning that is shown by the increase in

  5. Lightweight design for servo frame based on lattice material

    Science.gov (United States)

    Jin, Xin; Li, Guoxi; Liu, Encai; Gong, Jingzhong

    2017-06-01

    Lattice material infilling is an important way to achieve lightweight. Focusing on the problems of non-uniform arrangement and the finite element analysis (FEA) of lattice material in the parts, a lightweight design method based on lattice material is proposed with the spacecraft servo frame as the design object. Modal analysis and topology optimization are carried out according to the boundary conditions. The optimized density results are used to guide the design of lattice material parameters and arrangement. The equivalent mechanical properties of lattice material are obtained through the standard specimens experiments. The equivalent material FEA model of the lightweight servo frame is established, and the performance of the lightweight structure is tested by FEA simulation and experiment. The results show that under the impact condition, the lightweight servo frame meets the performance requirements and the simulation method through the equivalent material model is validated.

  6. New absorbent material acoustic based on kenaf’s fibre

    OpenAIRE

    Ramis, J.; Alba, J.; del Rey, R.; Escuder, E.; Sanchís, V. J.

    2010-01-01

    Acoustic Standards in the building are responsible for, companies and individuals, propose new acoustic materials for the sound isolation. This paper presents a new sound-absorbent material, it is based on natural fibres, particularly fibres of kenaf. It also proposes an empirical model for this material, this models depends on the frequency. There are accepted models from the scientific community about mineral wool, glass wool, rock wool, foam or polyester fibre. Several of these models are ...

  7. Biofuels 2020: Biorefineries based on lignocellulosic materials.

    Science.gov (United States)

    Valdivia, Miguel; Galan, Jose Luis; Laffarga, Joaquina; Ramos, Juan-Luis

    2016-09-01

    The production of liquid biofuels to blend with gasoline is of worldwide importance to secure the energy supply while reducing the use of fossil fuels, supporting the development of rural technology with knowledge-based jobs and mitigating greenhouse gas emissions. Today, engineering for plant construction is accessible and new processes using agricultural residues and municipal solid wastes have reached a good degree of maturity and high conversion yields (almost 90% of polysaccharides are converted into monosaccharides ready for fermentation). For the complete success of the 2G technology, it is still necessary to overcome a number of limitations that prevent a first-of-a-kind plant from operating at nominal capacity. We also claim that the triumph of 2G technology requires the development of favourable logistics to guarantee biomass supply and make all actors (farmers, investors, industrial entrepreneurs, government, others) aware that success relies on agreement advances. The growth of ethanol production for 2020 seems to be secured with a number of 2G plants, but public/private investments are still necessary to enable 2G technology to move on ahead from its very early stages to a more mature consolidated technology. © 2016 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

  8. Multimodal Feature-Based Surface Material Classification.

    Science.gov (United States)

    Strese, Matti; Schuwerk, Clemens; Iepure, Albert; Steinbach, Eckehard

    2017-01-01

    When a tool is tapped on or dragged over an object surface, vibrations are induced in the tool, which can be captured using acceleration sensors. The tool-surface interaction additionally creates audible sound waves, which can be recorded using microphones. Features extracted from camera images provide additional information about the surfaces. We present an approach for tool-mediated surface classification that combines these signals and demonstrate that the proposed method is robust against variable scan-time parameters. We examine freehand recordings of 69 textured surfaces recorded by different users and propose a classification system that uses perception-related features, such as hardness, roughness, and friction; selected features adapted from speech recognition, such as modified cepstral coefficients applied to our acceleration signals; and surface texture-related image features. We focus on mitigating the effect of variable contact force and exploration velocity conditions on these features as a prerequisite for a robust machine-learning-based approach for surface classification. The proposed system works without explicit scan force and velocity measurements. Experimental results show that our proposed approach allows for successful classification of textured surfaces under variable freehand movement conditions, exerted by different human operators. The proposed subset of six features, selected from the described sound, image, friction force, and acceleration features, leads to a classification accuracy of 74 percent in our experiments when combined with a Naive Bayes classifier.

  9. Listener: a probe into information based material specification

    DEFF Research Database (Denmark)

    Ramsgaard Thomsen, Mette; Karmon, Ayelet

    2011-01-01

    This paper presents the thinking and making of the architectural research probe Listener. Developed as an interdisciplinary collaboration between textile design and architecture, Listener explores how information based fabrication technologies are challenging the material practices of architecture....... The paper investigates how textile design can be understood as a model for architectural production providing new strategies for material specification and allowing the thinking of material as inherently variegated and performative. The paper traces the two fold information based strategies present...... in the Listener project. Firstly, the paper presents the design strategy leading to the development of bespoke interfaces between parametric design and CNC based textile fabrication. Secondly, by integrating structural and actuated materials the paper presents the making of a new class of materials...

  10. Mechanical properties of wood-based composite materials

    Science.gov (United States)

    Zhiyong Cai; Robert J. Ross

    2010-01-01

    The term composite is used to describe any wood material bonded together with adhesives. The current product mix ranges from fiberboard to laminated beams and components. In this chapter, wood-based composite materials are classified into the following categories: panel products (plywood, oriented strandboard (OSB), particleboard, fiberboard, medium-density fiberboard...

  11. E-Learning Activity-Based Material Recommendation System

    Science.gov (United States)

    Liu, Feng-jung; Shih, Bai-jiun

    2007-01-01

    Purpose: Computer based systems have great potential for delivering learning material. However, problems are encountered, such as: difficulty of Learning resource sharing, high redundancy of learning material, and deficiency of the course brief. In order to solve these problems, this paper aims to propose an automatic inquiring system for learning…

  12. New inorganic (an)ion exchangers based on Mg–Al hydrous oxides: (Alkoxide-free) sol–gel synthesis and characterisation

    KAUST Repository

    Chubar, Natalia

    2011-05-01

    New inorganic ion exchangers based on double Mg-Al hydrous oxides were generated via the new non-traditional sol-gel synthesis method which avoids using metal alkoxides as raw materials. Surface chemical and adsorptive properties of the final products were controlled by several ways of hydrogels and xerogels treatments which produced the materials of the layered structure, mixed hydrous oxides or amorphous adsorbents. The final adsorptive materials obtained via thermal treatment of xerogels were the layered mesoporous materials with carbonate in the interlayer space, surface abundance with hydroxylic groups and maximum adsorptive capacity to arsenate. Higher affinity of Mg-Al hydrous oxides towards H2AsO4- is confirmed by steep adsorption isotherms having plateau (removal capacity) at 220. mg[As]. gdw-1 for the best sample at pH = 7, fast adsorption kinetics and little pH effect. Adsorption of arsenite, fluoride, bromate, bromide, selenate, borate by Mg-Al hydrous oxides was few times high either competitive (depending on the anion) as compare with the conventional inorganic ion exchange adsorbents. © 2011 Elsevier Inc.

  13. Mechanistic Modeling Based PAT Implementation for Ion-Exchange Process Chromatography of Charge Variants of Monoclonal Antibody Products.

    Science.gov (United States)

    Kumar, Vijesh; Rathore, Anurag S

    2017-09-01

    Process chromatography is typically used to remove product related impurities and variants that have very similar physicochemical properties to the product. Baseline separation may not be achieved in most cases due to high protein loading and thus, pooling of the elution peak can be challenging for maximizing yield and achieving consistency in product quality. Batch-to-batch variability in quality of the feed material also occurs in commercial manufacturing. Mechanistic modeling of process chromatography, though non-trivial, can be an enabler for implementation of Process Analytical Technology. This paper presents one such application involving prediction of the impact of variability in feed quality and in gradient shape on separation of charge variants by cation exchange process chromatography and thereby facilitating feed forward control. Five batches having different compositions of charge variants have been used to demonstrate the proposed pooling strategy based on simulated chromatograms and the outcome has been compared to offline pooling based on fractionation. For all the conditions examined and for the desired target of main product (67%), the proposed approach resulted in remarkable consistency in product quality (67 ± 2%) while delivering a yield of greater than 90%. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Final Bioventing Pilot Test Work Plan for Base Exchange Service Station Underground Storage Tank Area, Vandenberg Air Force Base, California. Part I

    National Research Council Canada - National Science Library

    1992-01-01

    This pilot test work plan presents the scope of an in situ enhanced biological degradation, or "bioventing", pilot test for treatment of gasoline- contaminated soils at the Base Exchange Service Station (BXSS...

  15. Emerging terahertz photodetectors based on two-dimensional materials

    Science.gov (United States)

    Yang, Jie; Qin, Hua; Zhang, Kai

    2018-01-01

    Inspired by the innovations in photonics and nanotechnology, the remarkable properties of two-dimensional (2D) materials have renewed interest for the development of terahertz (THz) photodetectors. The versatility of these materials enables ultrafast and ultrasensitive photodetection of THz radiation at room temperature. The atomically thin characteristic together with van der Waals interactions among the layers make it easy to scaling down and integrate with other 2D materials based devices, as well as silicon chips. Efforts have increased fast in the past decade in developing proof-of-concept and the further prospective THz photodetectors based on 2D materials. Here, the recent progress on the exploring of THz photodetectors based on 2D materials is reviewed. We summarized the THz photodetectors under different physical mechanism and introduced the state-of-the-art THz photodetectors based on various promising 2D materials, such as graphene, transition metal dichalcogenides (TMDCs), black phosphorus (BP) and topological insulators (TIs). A brief discussion on the remaining challenges and a perspective of the 2D materials based THz photodetectors are also given.

  16. Polymers Based on Renewable Raw Materials – Part I

    Directory of Open Access Journals (Sweden)

    2013-09-01

    Full Text Available This paper gives an overview of the production and application of polymer materials based on renewable raw materials – biopolymers. It is pointed out that, investment of resources in the study of renewable raw materials in the last twenty years has led to the improvement of old and development of completely new chemical and biochemical processes for using biomass for the production of low molecular weight chemical substances, and especially for the production of biopolymers, which are biodegradable and compostable, and biopolymers which are nonbiodegradable. In the same period, producers of polymers based on fossil raw materials have also developed biopolymers that are biodegradable and some of them compostable and, most important, compatible with biopolymers based on renewable raw materials. The facts considering the state of biopolymers based on renewable raw materials on the market, and prediction of production increase over the next five years are also stated. Additionally, the main renewable raw materials and the biopolymers made from them that are already present in the world market are briefly listed. A short review of biopolymers based on cellulose from wood and annual plants is also given.

  17. From science to action: Principles for undertaking environmental research that enables knowledge exchange and evidence-based decision-making.

    Science.gov (United States)

    Cvitanovic, C; McDonald, J; Hobday, A J

    2016-12-01

    Effective conservation requires knowledge exchange among scientists and decision-makers to enable learning and support evidence-based decision-making. Efforts to improve knowledge exchange have been hindered by a paucity of empirically-grounded guidance to help scientists and practitioners design and implement research programs that actively facilitate knowledge exchange. To address this, we evaluated the Ningaloo Research Program (NRP), which was designed to generate new scientific knowledge to support evidence-based decisions about the management of the Ningaloo Marine Park in north-western Australia. Specifically, we evaluated (1) outcomes of the NRP, including the extent to which new knowledge informed management decisions; (2) the barriers that prevented knowledge exchange among scientists and managers; (3) the key requirements for improving knowledge exchange processes in the future; and (4) the core capacities that are required to support knowledge exchange processes. While the NRP generated expansive and multidisciplinary science outputs directly relevant to the management of the Ningaloo Marine Park, decision-makers are largely unaware of this knowledge and little has been integrated into decision-making processes. A range of barriers prevented efficient and effective knowledge exchange among scientists and decision-makers including cultural differences among the groups, institutional barriers within decision-making agencies, scientific outputs that were not translated for decision-makers and poor alignment between research design and actual knowledge needs. We identify a set of principles to be implemented routinely as part of any applied research program, including; (i) stakeholder mapping prior to the commencement of research programs to identify all stakeholders, (ii) research questions to be co-developed with stakeholders, (iii) implementation of participatory research approaches, (iv) use of a knowledge broker, and (v) tailored knowledge management

  18. Predicting protein retention time in ion-exchange chromatography based on three-dimensional protein characterization.

    Science.gov (United States)

    Xu, Li; Glatz, Charles E

    2009-01-09

    The isoelectric point (pI), molecular weight (M(W)) and aqueous two-phase partitioning coefficients of a set of model proteins were related to retention time in cation-exchange chromatography using partial least squares regression. A three-dimensional method which combined hydrophobic partitioning and two-dimensional electrophoresis was used to determine those three properties for a mixture of proteins. The regression models fit well (R(2)=0.913 and 0.873 for two resin types) considering the limited property basis, and were able to predict results for a small test set of proteins. The models showed that greater size and charge increased retention time, while the net influence of hydrophobicity depended on the base matrix type. This establishes the potential for the intended application to complex mixtures of host cell proteins.

  19. A security framework for nationwide health information exchange based on telehealth strategy.

    Science.gov (United States)

    Zaidan, B B; Haiqi, Ahmed; Zaidan, A A; Abdulnabi, Mohamed; Kiah, M L Mat; Muzamel, Hussaen

    2015-05-01

    This study focuses on the situation of health information exchange (HIE) in the context of a nationwide network. It aims to create a security framework that can be implemented to ensure the safe transmission of health information across the boundaries of care providers in Malaysia and other countries. First, a critique of the major elements of nationwide health information networks is presented from the perspective of security, along with such topics as the importance of HIE, issues, and main approaches. Second, a systematic evaluation is conducted on the security solutions that can be utilized in the proposed nationwide network. Finally, a secure framework for health information transmission is proposed within a central cloud-based model, which is compatible with the Malaysian telehealth strategy. The outcome of this analysis indicates that a complete security framework for a global structure of HIE is yet to be defined and implemented. Our proposed framework represents such an endeavor and suggests specific techniques to achieve this goal.

  20. High temperature proton exchange membranes based on polybenzimidazoles for fuel cells

    DEFF Research Database (Denmark)

    Li, Qingfeng; Jensen, Jens Oluf; Savinell, Robert F

    2009-01-01

    havebeenmadeincluding spectroscopy,wateruptake and acid doping, thermal and oxidative stability, conductivity, electro-osmoticwater drag, methanol crossover, solubility and permeability of gases, and oxygen reduction kinetics. Related fuel cell technologies such as electrode and MEA fabrication have been developed......To achieve high temperature operation of proton exchange membrane fuel cells (PEMFC), preferably under ambient pressure, acid–base polymer membranes represent an effective approach. The phosphoric acid-doped polybenzimidazole membrane seems so far the most successful system in the field. It has...... in recent years motivated extensive research activities with great progress. This treatise is devoted to updating the development, covering polymer synthesis, membrane casting, physicochemical characterizations and fuel cell technologies. To optimize the membrane properties, high molecular weight polymers...

  1. Catalyst Degradation in High Temperature Proton Exchange Membrane Fuel Cells Based on Acid Doped Polybenzimidazole Membranes

    DEFF Research Database (Denmark)

    Cleemann, Lars Nilausen; Buazar, F.; Li, Qingfeng

    2013-01-01

    contribution of the membrane degradation to the performance losses during the potential cycling tests. As the major mechanism of the fuel cell performance degradation, the electrochemical active area of the cathodic catalysts showed a steady decrease in the cyclic voltammetric measurements, which was also...... and multi‐walled carbon nanotubes were used as supports for electrode catalysts and evaluated in accelerated durability tests under potential cycling at 150 °C. Measurements of open circuit voltage, area specific resistance and hydrogen permeation through the membrane were carried out, indicating little......Degradation of carbon supported platinum catalysts is a major failure mode for the long term durability of high temperature proton exchange membrane fuel cells based on phosphoric acid doped polybenzimidazole membranes. With Vulcan carbon black as a reference, thermally treated carbon black...

  2. Durability Issues of High Temperature Proton Exchange Membrane Fuel Cells Based on Acid Doped Polybenzimidazole Membranes

    DEFF Research Database (Denmark)

    observed under continuous operation with hydrogen and air at 150-160oC, with a fuel cell performance degradation rate of 5-10 µV/h. Improvement of the membrane performance such as mechanical strength, swelling and oxidative stability has achieved by exploring the polymer chemistry, i.e. covalently......To achieve high temperature operation of proton exchange membrane fuel cells (PEMFC), preferably under ambient pressure, phosphoric acid doped polybenzimidazole (PBI) membrane represents an effective approach, which in recent years has motivated extensive research activities with great progress....... As a critical concern, issues of long term durability of PBI based fuel cells are addressed in this talk, including oxidative degradation of the polymer, mechanical failures of the membrane, acid leaching out, corrosion of carbon support and sintering of catalysts particles. Excellent polymer durability has...

  3. Fatigue Analysis of Proton Exchange Membrane Fuel Cell Stacks Based on Structural Stress Distribution

    Science.gov (United States)

    Wu, C. W.; Liu, B.; Wei, M. Y.; Liu, L. F.

    2017-05-01

    Proton exchange membrane fuel cell (PEMFC) stack usually undergoes various vibrations during packing, transportation and serving time, in particular for those used in the automobiles and portable equipment. Based on the Miner fatigue damage theory, the fatigue lives of the fuel cell components are first assessed. Then the component fatigue life contours of the stack are obtained under four working conditions, i.e. the three single-axial (in X-, Y- and Z-axis separately) and multi-axial random vibrations. Accordingly, the component damage under various vibrations is evaluated. The stress distribution on the gasket and PEM will greatly affect their fatigue lives. Finally, we compare the fatigue lives of 4-bolt- and 6-bolt-clamping stacks under the same total clamping force, and find that increasing the bolt number could improve the bolt fatigue lives.

  4. Process-based modelling of NH3 exchange with grazed grasslands

    Science.gov (United States)

    Móring, Andrea; Vieno, Massimo; Doherty, Ruth M.; Milford, Celia; Nemitz, Eiko; Twigg, Marsailidh M.; Horváth, László; Sutton, Mark A.

    2017-09-01

    In this study the GAG model, a process-based ammonia (NH3) emission model for urine patches, was extended and applied for the field scale. The new model (GAG_field) was tested over two modelling periods, for which micrometeorological NH3 flux data were available. Acknowledging uncertainties in the measurements, the model was able to simulate the main features of the observed fluxes. The temporal evolution of the simulated NH3 exchange flux was found to be dominated by NH3 emission from the urine patches, offset by simultaneous NH3 deposition to areas of the field not affected by urine. The simulations show how NH3 fluxes over a grazed field in a given day can be affected by urine patches deposited several days earlier, linked to the interaction of volatilization processes with soil pH dynamics. Sensitivity analysis showed that GAG_field was more sensitive to soil buffering capacity (β), field capacity (θfc) and permanent wilting point (θpwp) than the patch-scale model. The reason for these different sensitivities is dual. Firstly, the difference originates from the different scales. Secondly, the difference can be explained by the different initial soil pH and physical properties, which determine the maximum volume of urine that can be stored in the NH3 source layer. It was found that in the case of urine patches with a higher initial soil pH and higher initial soil water content, the sensitivity of NH3 exchange to β was stronger. Also, in the case of a higher initial soil water content, NH3 exchange was more sensitive to the changes in θfc and θpwp. The sensitivity analysis showed that the nitrogen content of urine (cN) is associated with high uncertainty in the simulated fluxes. However, model experiments based on cN values randomized from an estimated statistical distribution indicated that this uncertainty is considerably smaller in practice. Finally, GAG_field was tested with a constant soil pH of 7.5. The variation of NH3 fluxes simulated in this way

  5. Electrical conduction in solid materials physicochemical bases and possible applications

    CERN Document Server

    Suchet, J P

    2013-01-01

    Electrical Conduction in Solid Materials (Physicochemical Bases and Possible Applications) investigates the physicochemical bases and possible applications of electrical conduction in solid materials, with emphasis on conductors, semiconductors, and insulators. Topics range from the interatomic bonds of conductors to the effective atomic charge in conventional semiconductors and magnetic transitions in switching semiconductors. Comprised of 10 chapters, this volume begins with a description of electrical conduction in conductors and semiconductors, metals and alloys, as well as interatomic bon

  6. Te-based chalcogenide materials for selector applications.

    Science.gov (United States)

    Velea, A; Opsomer, K; Devulder, W; Dumortier, J; Fan, J; Detavernier, C; Jurczak, M; Govoreanu, B

    2017-08-14

    The implementation of dense, one-selector one-resistor (1S1R), resistive switching memory arrays, can be achieved with an appropriate selector for correct information storage and retrieval. Ovonic threshold switches (OTS) based on chalcogenide materials are a strong candidate, but their low thermal stability is one of the key factors that prevents rapid adoption by emerging resistive switching memory technologies. A previously developed map for phase change materials is expanded and improved for OTS materials. Selected materials from different areas of the map, belonging to binary Ge-Te and Si-Te systems, are explored. Several routes, including Si doping and reduction of Te amount, are used to increase the crystallization temperature. Selector devices, with areas as small as 55 × 55 nm2, were electrically assessed. Sub-threshold conduction models, based on Poole-Frenkel conduction mechanism, are applied to fresh samples in order to extract as-processed material parameters, such as trap height and density of defects, tailoring of which could be an important element for designing a suitable OTS material. Finally, a glass transition temperature estimation model is applied to Te-based materials in order to predict materials that might have the required thermal stability. A lower average number of p-electrons is correlated with a good thermal stability.

  7. Polyaniline (PANi based electrode materials for energy storage and conversion

    Directory of Open Access Journals (Sweden)

    Huanhuan Wang

    2016-09-01

    Full Text Available Polyaniline (PANi as one kind of conducting polymers has been playing a great role in the energy storage and conversion devices besides carbonaceous materials and metallic compounds. Due to high specific capacitance, high flexibility and low cost, PANi has shown great potential in supercapacitor. It alone can be used in fabricating an electrode. However, the inferior stability of PANi limits its application. The combination of PANi and other active materials (carbon materials, metal compounds or other polymers can surpass these intrinsic disadvantages of PANi. This review summarizes the recent progress in PANi based composites for energy storage/conversion, like application in supercapacitors, rechargeable batteries, fuel cells and water hydrolysis. Besides, PANi derived nitrogen-doped carbon materials, which have been widely employed as carbon based electrodes/catalysts, are also involved in this review. PANi as a promising material for energy storage/conversion is deserved for intensive study and further development.

  8. Antimicrobial clay-based materials for wound care.

    Science.gov (United States)

    Gaskell, Elsie E; Hamilton, Ashley R

    2014-04-01

    The historical use of clay minerals for the treatment of wounds and other skin ailments is well documented and continues within numerous human cultures the world over. However, a more scientific inquiry into the chemistry and properties of clay minerals emerged in the 19th century with work investigating their role within health gathering pace since the second half of the 20th century. This review gives an overview of clay minerals and how their properties can be manipulated to facilitate the treatment of infected wounds. Evidence of the antimicrobial and healing effects of some natural clay minerals is presented alongside a range of chemical modifications including metal-ion exchange, the formation of clay-drug composites and the development of various polymer-clay systems. While the evidence for applying these materials to infected wounds is limited, we contextualize and discuss the future of this research.

  9. Comparison of organic and inorganic ion exchange materials for removal of cesium and strontium from tank waste

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G. [Pacific Northwest National Lab., Richland, WA (United States)

    1996-10-01

    This work is part of an ESP task to develop high-capacity, selective, solid extractants for cesium, strontium, and technetium from nuclear wastes. Pacific Northwest National Laboratory (PNNL) staff are investigating novel ion exchangers for use in nuclear waste remediation (groundwater, high-level waste (HLW), and low-level waste (LLW)). Waste components targeted for remediation include cesium, strontium, and technetium.

  10. Creation of certified reference material based on glycine

    Directory of Open Access Journals (Sweden)

    M. P. Krasheninina

    2015-01-01

    Full Text Available The approaches for creating reference materials of glycine with certified values of nitrogen and base material mass fractions GSO 10272-2013 have been presented. Created certified reference material is intended for calibration and graduation of measurement equipments based on the different physical-chemical methods of analysis, as well as for check of error of measurement procedures. Besides GSO 10272-2013 can be used tor evaluating the purity of the components of medicinal preparations in pharmaceutical industry. GSO 10272-2013 will be used as an object for key comparisons in 2015.

  11. Modulations of interlayer exchange coupling through ultrathin MgO-based magnetic tunnel junctions: First-principles study

    Science.gov (United States)

    Wang, Shizhuo; Xia, Ke; Min, Tai; Ke, Youqi

    2017-07-01

    Ultrathin MgO-based magnetic tunnel junction (MTJ) features high electron/heat current density, presenting important applications in spintronics. Here, we report a first-principles study of the interlayer exchange coupling (IEC) through ultrathin MgO-based MTJs. We investigate the effects of different modulations on the IEC, including temperature, different interfacial disorders, and the type and thickness of the ferromagnetic (FM) materials. It is found that the interfacial disorders, such as oxygen vacancies, boron and carbon impurities, can significantly influence the magnitude and sign of the IEC. The presence of interfacial disorders enhances the anti-FM coupling contribution and reduces the FM coupling contribution to the total IEC, and can thus change the total IEC from FM to Anti-FM in the ultrathin MTJ. We also find that FM materials have important effects on IEC: the IEC with CoFe alloy exhibits much weaker dependence on the interfacial disorders and temperature than that with the Fe. Our first-principles results provide a good explanation for the serious inconsistency between previous experimental measurements. Moreover, by studying the junction structure Vacuum/FM1/MgO/FM2 (FM1, FM2=Fe, CoFe), we find that the ultrathin FM1 layers can dramatically enhance the FM IEC and the IEC enhancement significantly depends on the combination of FM1-FM2. We show that the enhanced FM IEC with ultrathin FM1 can be sustained with a considerable amount of surface roughness in FM1 and interfacial disorder.

  12. Design and Development of a Sub-Zero Fluid System for Demonstration of Orion's Phase Change Material Heat Exchangers on ISS

    Science.gov (United States)

    Sheth, Rubik B.; Ahlstrom, Thomas D.; Le, Hung V.

    2016-01-01

    NASA's Orion Multipurpose Crew Vehicle's Exploration Mission 2 is expected to loiter in Lunar orbit for a relatively long period of time. In low Lunar orbit (LLO) the thermal environment is cyclic - extremely cold in the eclipse and relatively hot near the subsolar point. Phase change material heat exchangers (PCM HXs) are the best option for long term missions in these environments. A PCM HX allows a vehicle to store excess waste energy by thawing a phase change material such as n-pentadecane wax. During portions of the orbit that are extremely cold, the excess energy is rejected, resolidifying the wax. Due to the inherent risk of compromising the heat exchanger during multiple freeze and thaw cycles, a unique payload was designed for the International Space Station to test and demonstration the functions of a PCM HX. The payload incorporates the use of a pumped fluid system and a thermoelectric heat exchanger to promote the freezing and thawing of the PCM HX. This paper shall review the design and development undertaken to build such a system.

  13. Human protamine-1 as an MRI reporter gene based on chemical exchange.

    Science.gov (United States)

    Bar-Shir, Amnon; Liu, Guanshu; Chan, Kannie W Y; Oskolkov, Nikita; Song, Xiaolei; Yadav, Nirbhay N; Walczak, Piotr; McMahon, Michael T; van Zijl, Peter C M; Bulte, Jeff W M; Gilad, Assaf A

    2014-01-17

    Genetically engineered reporters have revolutionized the understanding of many biological processes. MRI-based reporter genes can dramatically improve our ability to monitor dynamic gene expression and allow coregistration of subcellular genetic information with high-resolution anatomical images. We have developed a biocompatible MRI reporter gene based on a human gene, the human protamine-1 (hPRM1). The arginine-rich hPRM1 (47% arginine residues) generates high MRI contrast based on the chemical exchange saturation transfer (CEST) contrast mechanism. The 51 amino acid-long hPRM1 protein was fully synthesized using microwave-assisted technology, and the CEST characteristics of this protein were compared to other CEST-based contrast agents. Both bacterial and human cells were engineered to express an optimized hPRM1 gene and showed higher CEST contrast compared to controls. Live cells expressing the hPRM1 reporter gene, and embedded in three-dimensional culture, also generated higher CEST contrast compared to wild-type live cells.

  14. A Provably Secure Revocable ID-Based Authenticated Group Key Exchange Protocol with Identifying Malicious Participants

    Directory of Open Access Journals (Sweden)

    Tsu-Yang Wu

    2014-01-01

    Full Text Available The existence of malicious participants is a major threat for authenticated group key exchange (AGKE protocols. Typically, there are two detecting ways (passive and active to resist malicious participants in AGKE protocols. In 2012, the revocable identity- (ID- based public key system (R-IDPKS was proposed to solve the revocation problem in the ID-based public key system (IDPKS. Afterwards, based on the R-IDPKS, Wu et al. proposed a revocable ID-based AGKE (RID-AGKE protocol, which adopted a passive detecting way to resist malicious participants. However, it needs three rounds and cannot identify malicious participants. In this paper, we fuse a noninteractive confirmed computation technique to propose the first two-round RID-AGKE protocol with identifying malicious participants, which is an active detecting way. We demonstrate that our protocol is a provably secure AGKE protocol with forward secrecy and can identify malicious participants. When compared with the recently proposed ID/RID-AGKE protocols, our protocol possesses better performance and more robust security properties.

  15. Recent advances in the Si-based nanocomposite materials as high capacity anode materials for lithium ion batteries

    National Research Council Canada - National Science Library

    Kim, Hansu; Lee, Eung-Ju; Sun, Yang-Kook

    2014-01-01

    ..., electric vehicles and energy storage units for renewable energy. This review focuses on high capacity Si based nanostructured anode materials composed of Si and various inactive phase materials...

  16. Phase Change Material Based Accumulation Panels in Combination with Renewable Energy Sources and Thermoelectric Cooling

    Directory of Open Access Journals (Sweden)

    Jan Skovajsa

    2017-01-01

    Full Text Available The article deals with the use of modern materials and technologies that can improve the thermal comfort in buildings. The article describes the design and usage of a special accumulation device, which is composed of thermal panels based on phase change materials (PCMs. The thermal panels have an integrated tube heat exchanger and heating foils. The technology can be used as a passive or active system for heating and cooling. It is designed as a “green technology”, so it is able to use renewable energy sources, e.g., photovoltaic (PV panels, solar thermal collectors and heat pumps. Moreover, an interesting possibility is the ability to use thermoelectric coolers. In the research, measurements of the different operating modes were made, and the results are presented in the text. The measurement approves that the technology improves the thermal capacity of the building, and it is possible to use it for active heating and cooling.

  17. Advanced Materials for PEM-Based Fuel Cell Systems

    Energy Technology Data Exchange (ETDEWEB)

    James E. McGrath; Donald G. Baird; Michael von Spakovsky

    2005-10-26

    Proton exchange membrane fuel cells (PEMFCs) are quickly becoming attractive alternative energy sources for transportation, stationary power, and small electronics due to the increasing cost and environmental hazards of traditional fossil fuels. Two main classes of PEMFCs include hydrogen/air or hydrogen/oxygen fuel cells and direct methanol fuel cells (DMFCs). The current benchmark membrane for both types of PEMFCs is Nafion, a perfluorinated sulfonated copolymer made by DuPont. Nafion copolymers exhibit good thermal and chemical stability, as well as very high proton conductivity under hydrated conditions at temperatures below 80 degrees C. However, application of these membranes is limited due to their high methanol permeability and loss of conductivity at high temperatures and low relative humidities. These deficiencies have led to the search for improved materials for proton exchange membranes. Potential PEMs should have good thermal, hydrolytic, and oxidative stability, high proton conductivity, selective permeability, and mechanical durability over long periods of time. Poly(arylene ether)s, polyimides, polybenzimidazoles, and polyphenylenes are among the most widely investigated candidates for PEMs. Poly(arylene ether)s are a promising class of proton exchange membranes due to their excellent thermal and chemical stability and high glass transition temperatures. High proton conductivity can be achieved through post-sulfonation of poly(arylene ether) materials, but this most often results in very high water sorption or even water solubility. Our research has shown that directly polymerized poly(arylene ether) copolymers show important advantages over traditional post-sulfonated systems and also address the concerns with Nafion membranes. These properties were evaluated and correlated with morphology, structure-property relationships, and states of water in the membranes. Further improvements in properties were achieved through incorporation of inorganic

  18. Advanced Materials for PEM-Based Fuel Cell Systems

    Energy Technology Data Exchange (ETDEWEB)

    James E. McGrath

    2005-10-26

    Proton exchange membrane fuel cells (PEMFCs) are quickly becoming attractive alternative energy sources for transportation, stationary power, and small electronics due to the increasing cost and environmental hazards of traditional fossil fuels. Two main classes of PEMFCs include hydrogen/air or hydrogen/oxygen fuel cells and direct methanol fuel cells (DMFCs). The current benchmark membrane for both types of PEMFCs is Nafion, a perfluorinated sulfonated copolymer made by DuPont. Nafion copolymers exhibit good thermal and chemical stability, as well as very high proton conductivity under hydrated conditions at temperatures below 80 °C. However, application of these membranes is limited due to their high methanol permeability and loss of conductivity at high temperatures and low relative humidities. These deficiencies have led to the search for improved materials for proton exchange membranes. Potential PEMs should have good thermal, hydrolytic, and oxidative stability, high proton conductivity, selective permeability, and mechanical durability over long periods of time. Poly(arylene ether)s, polyimides, polybenzimidazoles, and polyphenylenes are among the most widely investigated candidates for PEMs. Poly(arylene ether)s are a promising class of proton exchange membranes due to their excellent thermal and chemical stability and high glass transition temperatures. High proton conductivity can be achieved through post-sulfonation of poly(arylene ether) materials, but this most often results in very high water sorption or even water solubility. Our research has shown that directly polymerized poly(arylene ether) copolymers show important advantages over traditional post-sulfonated systems and also address the concerns with Nafion membranes. These properties were evaluated and correlated with morphology, structure-property relationships, and

  19. Radial variations in cation exchange capacity and base saturation rate in the wood of pedunculate oak and European beech

    Energy Technology Data Exchange (ETDEWEB)

    Herbauts, J.; Penninckx, V.; Gruber, W.; Meerts, P. [Universite Libre de Bruxelles, Laboratoire de genetique et d' ecologie vegetales, Brussels (Belgium)

    2002-10-01

    Visual observation of pedunculate oak trees and European beech trees in a mixed forest stand in the Belgian Ardennes revealed decreasing cation concentration profiles in wood. In order to determine whether these profiles are attributable to endogenous factors or to decreased availability of cations in the soil, radial profiles of water-soluble, exchangeable and total cations were investigated. Cation exchange capacity of wood was also determined. Results showed wood cation exchange capacity to decrease from pith to bark in European beech and from pith to outer heartwood in pedunculate oak. Decreasing profiles of exchangeable calcium and magnesium in peduncular oak and exchangeable calcium in European beech were found to be strongly constrained by cation exchange capacity, and thus not related to environmental change. Base cation saturation rate showed no consistent radial change in either species. It was concluded that the results did not provide convincing evidence to attribute the decrease in divalent cation concentration in pedunculate oak and European beech in this location to be due to atmospheric pollution. 42 refs., 1 tab., 4 figs.

  20. Ventilation Heat Recovery from Wood-Burning Domestic Flues. A Theoretical Analysis Based on a Triple Concentric Tube Heat Exchanger

    Directory of Open Access Journals (Sweden)

    Lionel Druette

    2013-01-01

    Full Text Available This paper presents a new air-heating system concept for energy-efficient dwellings. It is a system designed to heat a low-energy building by coupling a heat-recovery ventilation system with a three-fluid heat exchanger located on the chimney of a wood-pellet stove. The proposed work focuses on the heat transfer that occurs between flue gases, the ventilation air and the combustion air within a triple concentric tube heat exchanger with no insulation at its outer surface. The main objective is to predict outlet temperature for the specific geometry of the heat exchanger studied here. Thus, the governing differential equations are derived for a counter-co-current flow arrangement of the three fluids. Then analytical solutions for the steady-state temperature distribution are obtained as well as the amount of heat transferred to the outside. An expression for the effectiveness of the heat exchanger is also proposed. Based on these results, calculations are performed on a case study to predict the fluid temperature distribution along the heat exchanger. Finally, a parametric study is carried out on this case study to assess the influence of the relevant parameters on the effectiveness of the heat exchanger. In addition, computation of heat losses to the outside justifies whether insulation is needed.

  1. Reading Sŏktok Kugyŏl materials based on Ŏnhae materials

    Directory of Open Access Journals (Sweden)

    Satoshi JOHO

    2014-12-01

    Full Text Available In this paper, we discussed some advantages of and points of attempt to research how to read Hancha (漢字 with Kugyŏl (口訣 markings based on the premise, that the tradition of Hanmun Hundok (漢文訓讀 in Sŏktok Kugyŏl (釋讀口訣 materials has been succeeded to Ŏnhae (諺解 materials since the mid-15th century, the promulgation of Hunmin Chyŏngŭm (訓民正音, and based on Ŏnhae (諺解 system in these Ŏnhae (諺解 materials. As a result, Hundok (訓讀 systems of Sŏktok Kugyŏl (釋讀口訣 materials had much resemblance to the Non-Buddhist (Confucian Ŏnhae (諺解 materials since the end of 15th century. Therefore, Non-Buddhist (Confucian Ŏnhae (諺解 materials occupy an important position to consider the reading methods of Sŏktok Kugyŏl (釋讀口訣 materials.

  2. The CROPROTECT project and wider opportunities to improve farm productivity through web-based knowledge exchange.

    Science.gov (United States)

    Bruce, Toby J A

    2016-05-01

    A key global 21st century challenge is to maximize agricultural production while minimizing use of resources such as land, water, and energy to meet rising demand for produce. To meet this challenge, while also adapting to climate change, agriculture will have to become more knowledge intensive and deploy smarter farming techniques. The intention of this study was to: (1) Highlight the opportunity for web-based knowledge exchange to increase farm productivity and thus contribute to achieving food and energy security, (2) Give some examples of online farming information services such as the "CROPROTECT" tool I am developing in the UK, the CABI "Plantwise" Knowledge Bank and the IRRI "Rice Doctor," and (3) Consider lessons learnt so far. There are huge opportunities to facilitate knowledge exchange through online systems for farmers and people who advise farmers. CROPROTECT is interacting with users to determine priorities in terms of the pests, weeds, and diseases covered and is providing key information to assist with their management. Knowledge is a critical input for farming systems. Crop protection in particular is becoming more difficult due to evolution of pest resistance and changes in legislation. Up to date information can be made rapidly available and shared online through websites and smartphone Apps. Agricultural extension no longer relies solely on physical meetings and printed documents. The capacity to share information via the Internet is tremendous with its potential to reach a wide audience in the farming community, to provide rapid updates and to interact more with the users. However, in an era of information deluge, accessing relevant information and ensuring reliability are essential considerations. There is also a need to bring science and farming communities together to turn information into relevant farming knowledge.

  3. Multiscale experimental mechanics of hierarchical carbon-based materials.

    Science.gov (United States)

    Espinosa, Horacio D; Filleter, Tobin; Naraghi, Mohammad

    2012-06-05

    Investigation of the mechanics of natural materials, such as spider silk, abalone shells, and bone, has provided great insight into the design of materials that can simultaneously achieve high specific strength and toughness. Research has shown that their emergent mechanical properties are owed in part to their specific self-organization in hierarchical molecular structures, from nanoscale to macroscale, as well as their mixing and bonding. To apply these findings to manmade materials, researchers have devoted significant efforts in developing a fundamental understanding of multiscale mechanics of materials and its application to the design of novel materials with superior mechanical performance. These efforts included the utilization of some of the most promising carbon-based nanomaterials, such as carbon nanotubes, carbon nanofibers, and graphene, together with a variety of matrix materials. At the core of these efforts lies the need to characterize material mechanical behavior across multiple length scales starting from nanoscale characterization of constituents and their interactions to emerging micro- and macroscale properties. In this report, progress made in experimental tools and methods currently used for material characterization across multiple length scales is reviewed, as well as a discussion of how they have impacted our current understanding of the mechanics of hierarchical carbon-based materials. In addition, insight is provided into strategies for bridging experiments across length scales, which are essential in establishing a multiscale characterization approach. While the focus of this progress report is in experimental methods, their concerted use with theoretical-computational approaches towards the establishment of a robust material by design methodology is also discussed, which can pave the way for the development of novel materials possessing unprecedented mechanical properties. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Control of proton exchange membrane fuel cell system breathing based on maximum net power control strategy

    Science.gov (United States)

    Li, Qi; Chen, Weirong; Liu, Zhixiang; Guo, Ai; Liu, Shukui

    2013-11-01

    In order to achieve the maximum net power, the analysis for the maximum net power characterization of a proton exchange membrane fuel cell (PEMFC) system is carried out. A maximum net power control (MNPC) strategy based on an implicit generalized predictive control (IGPC) and a reference governor is proposed to keep optimal oxygen excess ratio (OER) trajectory. The IGPC based on an effective informed adaptive particle swarm optimization (EIA-PSO) algorithm is developed to solve the predictive control law and reduce the computational complexity in the rolling optimization process. The simulations of three conditional tests are implemented and the results demonstrate that the proposed strategy can track the optimal OER trajectory, reduce the parasitic power and maximize the output net power. The comprehensive comparisons based on three conditional tests verify that the MNPC-IGPC has better robust performance in the presence of large disturbances, time delay and various noises. The experimental comparison with internal control system of Ballard 1.2 kW Nexa Power Module testifies the validity of the MNPC-IGPC for increasing the net power. Hence, this proposed strategy can provide better behavior to guarantee optimal OER trajectory and the maximum net power even though the disturbances and uncertainties occur.

  5. Material characterization of microsphere-based scaffolds with encapsulated raw materials.

    Science.gov (United States)

    Sridharan, BanuPriya; Mohan, Neethu; Berkland, Cory J; Detamore, Michael S

    2016-06-01

    "Raw materials," or materials capable of serving both as building blocks and as signals, which are often but not always natural materials, are taking center stage in biomaterials for contemporary regenerative medicine. In osteochondral tissue engineering, a field leveraging the underlying bone to facilitate cartilage regeneration, common raw materials include chondroitin sulfate (CS) for cartilage and β-tricalcium phosphate (TCP) for bone. Building on our previous work with gradient scaffolds based on microspheres, here we delved deeper into the characterization of individual components. In the current study, the release of CS and TCP from poly(D, L-lactic-co-glycolic acid) (PLGA) microsphere-based scaffolds was evaluated over a time period of 4 weeks. Raw material encapsulated groups were compared to 'blank' groups and evaluated for surface topology, molecular weight, and mechanical performance as a function of time. The CS group may have led to increased surface porosity, and the addition of CS improved the mechanical performance of the scaffold. The finding that CS was completely released into the surrounding media by 4 weeks has a significant impact on future in vivo studies, given rapid bioavailability. The addition of TCP seemed to contribute to the rough external appearance of the scaffold. The current study provides an introduction to degradation patterns of homogenous raw material encapsulated scaffolds, providing characterization data to advance the field of microsphere-based scaffolds in tissue engineering. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Gas diffusion electrode based on electrospun Pani/CNF nanofibers hybrid for proton exchange membrane fuel cells (PEMFC) applications

    Science.gov (United States)

    Hezarjaribi, M.; Jahanshahi, M.; Rahimpour, A.; Yaldagard, M.

    2014-03-01

    A novel hybrid system has been investigated based on polyaniline/carbon nanofiber (Pani/CNF) electrospun nanofibers for modification of gas diffusion electrode (GDE) in proton exchange membrane fuel cells (PEMFC). Pani/CNF hybrid nanofibers were synthesized directly on carbon paper by electrospinning method. For preparation of catalyst ink, 20 wt.% Pt/C electrocatalyst with a platinum loading of 0.4 mg cm-2 was prepared by polyol technique. SEM studies applied for morphological study of the modified GDE with hybrid nanofibers. This technique indicated that the electrospun nanofibers had a diameter of roughly 100 nm. XRD patterns also showed that the average size of Pt nanoparticles was about 2 nm. Subsequently, comparison of the hybrid electrode electrochemical behavior and 20 wt.% Pt/C commercial one was studied by cyclic voltammetry experiment. The electrochemical data indicated that the hybrid electrode exhibited higher current density (about 15 mA cm-2) and ESA (160 m2 gr-1) than commercial Pt/C with amount of about 10 mA cm-2 and 114 m2 gr-1, respectively. The results herein demonstrate that Pani/CNF nanofibers can be used as a good alternative electrode material for PEMFCs.

  7. Gas diffusion electrode based on electrospun Pani/CNF nanofibers hybrid for proton exchange membrane fuel cells (PEMFC) applications

    Energy Technology Data Exchange (ETDEWEB)

    Hezarjaribi, M.; Jahanshahi, M., E-mail: mjahan@nit.ac.ir; Rahimpour, A.; Yaldagard, M.

    2014-03-01

    A novel hybrid system has been investigated based on polyaniline/carbon nanofiber (Pani/CNF) electrospun nanofibers for modification of gas diffusion electrode (GDE) in proton exchange membrane fuel cells (PEMFC). Pani/CNF hybrid nanofibers were synthesized directly on carbon paper by electrospinning method. For preparation of catalyst ink, 20 wt.% Pt/C electrocatalyst with a platinum loading of 0.4 mg cm{sup −2} was prepared by polyol technique. SEM studies applied for morphological study of the modified GDE with hybrid nanofibers. This technique indicated that the electrospun nanofibers had a diameter of roughly 100 nm. XRD patterns also showed that the average size of Pt nanoparticles was about 2 nm. Subsequently, comparison of the hybrid electrode electrochemical behavior and 20 wt.% Pt/C commercial one was studied by cyclic voltammetry experiment. The electrochemical data indicated that the hybrid electrode exhibited higher current density (about 15 mA cm{sup −2}) and ESA (160 m{sup 2} gr{sup −1}) than commercial Pt/C with amount of about 10 mA cm{sup −2} and 114 m{sup 2} gr{sup −1}, respectively. The results herein demonstrate that Pani/CNF nanofibers can be used as a good alternative electrode material for PEMFCs.

  8. Effect of Material Ion Exchanges on the Mechanical Stiffness Properties and Shear Deformation of Hydrated Cement Material Chemistry Structure C-S-H Jennit - A Computational Modeling Study

    Science.gov (United States)

    2014-01-01

    to improve material performances. For example, cementitious materials that are the binders for mortar and concrete have material, geometrical... nanotechnology research from the nascent exploratory research which was initiated mostly to understand underlining principles to designing new materials...2005. 4. Taylor, H.F., Cement chemistry. 1997: Thomas Telford. 5. Mindess, S., J.F. Young, and D. Darwin, Concrete . 2003. 6. Nonat, A., The

  9. Performance evaluation of 24 ion exchange materials for removing cesium and strontium from actual and simulated N-Reactor storage basin water

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G.N.; Carson, K.J.; DesChane, J.R.; Elovich, R.J.

    1997-09-01

    This report describes the evaluation of 24 organic and inorganic ion exchange materials for removing cesium and strontium from actual and simulated waters from the 100 Area 105 N-Reactor fuel storage basin. The data described in this report can be applied for developing and evaluating ion exchange pre-treatment process flowsheets. Cesium and strontium batch distribution ratios (K{sub d}`s), decontamination factors (DF), and material loadings (mmol g{sup -1}) are compared as a function of ion exchange material and initial cesium concentration. The actual and simulated N-Basin waters contain relatively low levels of aluminum, barium, calcium, potassium, and magnesium (ranging from 8.33E-04 to 6.40E-05 M), with slightly higher levels of boron (6.63E-03 M) and sodium (1.62E-03 M). The {sup 137}Cs level is 1.74E-06 Ci L-{sup 1} which corresponds to approximately 4.87E-10 M Cs. The initial Na/Cs ratio was 3.33E+06. The concentration of total strontium is 4.45E-06 M, while the {sup 90}Sr radioactive component was measured to be 6.13E-06 Ci L{sup -1}. Simulant tests were conducted by contacting 0.067 g or each ion exchange material with approximately 100 mL of either the actual or simulated N-Basin water. The simulants contained variable initial cesium concentrations ranging from 1.00E-04 to 2.57E- 10 M Cs while all other components were held constant. For all materials, the average cesium K{sub d} was independent of cesium concentration below approximately 1.0E-06 M. Above this level, the average cesium K{sub d} values decreased significantly. Cesium K{sub d} values exceeding 1.0E+07 mL g{sup -1} were measured in the simulated N-Basin water. However, when measured in the actual N-Basin water the values were several orders of magnitude lower, with a maximum of 1.24E+05 mL g{sup -1} observed.

  10. Frequency analysis of tick quotes on the foreign exchange market and agent-based modeling: A spectral distance approach

    Science.gov (United States)

    Sato, Aki-Hiro

    2007-08-01

    High-frequency financial data of the foreign exchange market (EUR/CHF, EUR/GBP, EUR/JPY, EUR/NOK, EUR/SEK, EUR/USD, NZD/USD, USD/CAD, USD/CHF, USD/JPY, USD/NOK, and USD/SEK) are analyzed by utilizing the Kullback-Leibler divergence between two normalized spectrograms of the tick frequency and the generalized Jensen-Shannon divergence among them. The temporal structure variations of the similarity between currency pairs is detected and characterized. A simple agent-based model in which N market participants exchange M currency pairs is proposed. The equation for the tick frequency is approximately derived theoretically. Based on the analysis of this model, the spectral distance of the tick frequency is associated with the similarity of the behavior (perception and decision) of the market participants in exchanging these currency pairs.

  11. A Task-Based Approach to Materials Development

    Science.gov (United States)

    Nunan, David

    2010-01-01

    The purpose of this chapter is to present a task-based approach to materials development. In the first part of the chapter, I sketch out the evolution of task based language teaching, drawing on a distinction between synthetic and analytical approaches to syllabus design first articulated by Wilkins (1976).

  12. A Task-based Approach to Materials Development

    OpenAIRE

    David Nunan

    2010-01-01

    The purpose of this chapter is to present a task-based approach to materials development. In the first part of the chapter, I sketch out the evolution of task based language teaching, drawing on a distinction between synthetic and analytical approaches to syllabus design first articulated by Wilkins (1976).

  13. A Task-based Approach to Materials Development

    Directory of Open Access Journals (Sweden)

    David Nunan

    2010-07-01

    Full Text Available The purpose of this chapter is to present a task-based approach to materials development. In the first part of the chapter, I sketch out the evolution of task based language teaching, drawing on a distinction between synthetic and analytical approaches to syllabus design first articulated by Wilkins (1976.

  14. Fifty years in studying carbon-based materials

    Science.gov (United States)

    Dresselhaus, Mildred S.

    2012-01-01

    A review is presented based on our 50 year involvement in studying carbon materials physics and carbon-based nanostructures. The review topics include an early history of studies of graphene and graphite, graphite intercalation compounds, forerunners of nano-carbons, fullerenes, carbon nanotubes and, finally, graphene and graphene nanoribbons.

  15. Using Android-Based Educational Game for Learning Colloid Material

    Science.gov (United States)

    Sari, S.; Anjani, R.; Farida, I.; Ramdhani, M. A.

    2017-09-01

    This research is based on the importance of the development of student’s chemical literacy on Colloid material using Android-based educational game media. Educational game products are developed through research and development design. In the analysis phase, material analysis is performed to generate concept maps, determine chemical literacy indicators, game strategies and set game paths. In the design phase, product packaging is carried out, then validation and feasibility test are performed. Research produces educational game based on Android that has the characteristics that is: Colloid material presented in 12 levels of game in the form of questions and challenges, presents visualization of discourse, images and animation contextually to develop the process of thinking and attitude. Based on the analysis of validation and trial results, the product is considered feasible to use.

  16. Foreign Exchange Market Contagion in the Asian Crisis: A Regression-based Approach

    NARCIS (Netherlands)

    van Horen, N.; Jager, H.; Klaassen, F.J.G.M.

    2006-01-01

    This paper investigates whether, during the Asian crisis, contagion occurred from Thailand to the other crisis countries through the foreign exchange market, and, if so, determines the contribution of this contagion to the crisis. More specifically, we examine whether the effect of the exchange

  17. Measurement-based upscaling of pan Arctic net ecosystem exchange: the PANEEx project

    DEFF Research Database (Denmark)

    Mbufong, Herbert Njuabe; Kusbach, Antonin; Lund, Magnus

    2015-01-01

    The high variability in Arctic tundra net ecosystem exchange (NEE) of carbon (C) can be attributed to the high spatial heterogeneity of Arctic tundra due to the complex topography. Current models of C exchange handle the Arctic as either a single or few ecosystems, responding to environmental cha...

  18. Identification of collagen-based materials in cultural heritage.

    Science.gov (United States)

    Kirby, Daniel P; Buckley, Michael; Promise, Ellen; Trauger, Sunia A; Holdcraft, T Rose

    2013-09-07

    All stakeholders in cultural heritage share an interest in fabrication methods and material technology. Until now methods for analysis of organic materials, particularly proteins, have not been widely available to researchers at cultural institutions. This paper will describe an analytical method for the identification of collagen-based materials from soft tissue sources and show examples of its application to diverse museum objects. The method, peptide mass fingerprinting (PMF), uses enzymatic digestion of extracted proteins to produce a mixture of peptides. The mass spectrum of the mixture contains characteristic marker ions-a peptide mass fingerprint-which are compared to species-specific markers from references as the basis of identification. Preliminary results indicate that analysis of materials from aged samples, several different tissue types, and tanned or untanned materials yields comparable PMF results. Significantly, PMF is simple, rapid, sensitive and specific, has been implemented in a museum laboratory, and is being practiced successfully by non-specialists.

  19. Ontology based heterogeneous materials database integration and semantic query

    Directory of Open Access Journals (Sweden)

    Shuai Zhao

    2017-10-01

    Full Text Available Materials digital data, high throughput experiments and high throughput computations are regarded as three key pillars of materials genome initiatives. With the fast growth of materials data, the integration and sharing of data is very urgent, that has gradually become a hot topic of materials informatics. Due to the lack of semantic description, it is difficult to integrate data deeply in semantic level when adopting the conventional heterogeneous database integration approaches such as federal database or data warehouse. In this paper, a semantic integration method is proposed to create the semantic ontology by extracting the database schema semi-automatically. Other heterogeneous databases are integrated to the ontology by means of relational algebra and the rooted graph. Based on integrated ontology, semantic query can be done using SPARQL. During the experiments, two world famous First Principle Computational databases, OQMD and Materials Project are used as the integration targets, which show the availability and effectiveness of our method.

  20. Ontology based heterogeneous materials database integration and semantic query

    Science.gov (United States)

    Zhao, Shuai; Qian, Quan

    2017-10-01

    Materials digital data, high throughput experiments and high throughput computations are regarded as three key pillars of materials genome initiatives. With the fast growth of materials data, the integration and sharing of data is very urgent, that has gradually become a hot topic of materials informatics. Due to the lack of semantic description, it is difficult to integrate data deeply in semantic level when adopting the conventional heterogeneous database integration approaches such as federal database or data warehouse. In this paper, a semantic integration method is proposed to create the semantic ontology by extracting the database schema semi-automatically. Other heterogeneous databases are integrated to the ontology by means of relational algebra and the rooted graph. Based on integrated ontology, semantic query can be done using SPARQL. During the experiments, two world famous First Principle Computational databases, OQMD and Materials Project are used as the integration targets, which show the availability and effectiveness of our method.

  1. An experimental and numerical study of a jetfire stop material and a new helical flow heat exchanger

    Energy Technology Data Exchange (ETDEWEB)

    Austegard, Anders

    1997-12-31

    This thesis consists of two parts. Part 1: Experimental and numerical study of jetfire stop, and Part 2: Experimental and numerical study of a new kind of shell and tube heat exchanger with helical flow on shell side. Part 1 describes the development of the model for simulation of the temperature development through Viking jetfirestop. A simulation program is developed that calculates the temperature development through Viking jetfire stop. In the development of the model, measurements of reaction energy, pyrolysis and heat conductivity at low temperatures are made. The conductivity at higher temperatures and when pyrolysis reactions are going on is estimated experimentally and by numerical calculations. Full-scale jet fire test and small-scale xenon lamp experiments are made to test the simulation model. Part 2 contains the development of a model that simulate the fluid flow and heat transfer in a helical flow shell and tube heat exchanger. It consists of the development of a porosity model and a model for pressure drop and heat transfer as well as experiments in non-standard tube layouts. Results from the simulation program are compared with experiments on a helical flow shell and tube heat exchanger. There is a separate appendix volume. 62 refs., 152 figs., 22 tabs.

  2. Graphene-based materials: synthesis, characterization, properties, and applications.

    Science.gov (United States)

    Huang, Xiao; Yin, Zongyou; Wu, Shixin; Qi, Xiaoying; He, Qiyuan; Zhang, Qichun; Yan, Qingyu; Boey, Freddy; Zhang, Hua

    2011-07-18

    Graphene, a two-dimensional, single-layer sheet of sp(2) hybridized carbon atoms, has attracted tremendous attention and research interest, owing to its exceptional physical properties, such as high electronic conductivity, good thermal stability, and excellent mechanical strength. Other forms of graphene-related materials, including graphene oxide, reduced graphene oxide, and exfoliated graphite, have been reliably produced in large scale. The promising properties together with the ease of processibility and functionalization make graphene-based materials ideal candidates for incorporation into a variety of functional materials. Importantly, graphene and its derivatives have been explored in a wide range of applications, such as electronic and photonic devices, clean energy, and sensors. In this review, after a general introduction to graphene and its derivatives, the synthesis, characterization, properties, and applications of graphene-based materials are discussed. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. An Overview of Composting Based on Variable Feedstock Material

    Directory of Open Access Journals (Sweden)

    Kadir Aeslina Abdul

    2016-01-01

    Full Text Available Composting is a biological treatment method that provides a potential sustainable way to convert food waste into organic compost. In composting, the feedstock material is an important item to ensure the success of the composting process. This paper reviewed the process of composting based on implementation different types of feedstock, namely: 1 animal waste such as cow dung, poultry litter, swine manure and chicken manure; and 2 agricultural waste such as sawdust, rice straw, bran, bagasse, banana waste and pine chip. The result for poultry litter, cow manure, swine manure, sawdust and rice straw has C/N ratio lower than 20 at final composting process which is considered as satisfactory level for compost maturity. As a conclusion, the selection of the feedstock material is based on the characteristics of the material itself and the selection of materials is important for the quality of compost.

  4. Vertical Transistors Based on 2D Materials: Status and Prospects

    Directory of Open Access Journals (Sweden)

    Filippo Giannazzo

    2018-01-01

    Full Text Available Two-dimensional (2D materials, such as graphene (Gr, transition metal dichalcogenides (TMDs and hexagonal boron nitride (h-BN, offer interesting opportunities for the implementation of vertical transistors for digital and high-frequency electronics. This paper reviews recent developments in this field, presenting the main vertical device architectures based on 2D/2D or 2D/3D material heterostructures proposed so far. For each of them, the working principles and the targeted application field are discussed. In particular, tunneling field effect transistors (TFETs for beyond-CMOS low power digital applications are presented, including resonant tunneling transistors based on Gr/h-BN/Gr stacks and band-to-band tunneling transistors based on heterojunctions of different semiconductor layered materials. Furthermore, recent experimental work on the implementation of the hot electron transistor (HET with the Gr base is reviewed, due to the predicted potential of this device for ultra-high frequency operation in the THz range. Finally, the material sciences issues and the open challenges for the realization of 2D material-based vertical transistors at a large scale for future industrial applications are discussed.

  5. Graphene-based filament material for thermal ionization

    Energy Technology Data Exchange (ETDEWEB)

    Hewitt, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Shick, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Siegfried, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-09-19

    The use of graphene oxide materials for thermal ionization mass spectrometry analysis of plutonium and uranium has been investigated. Filament made from graphene oxide slurries have been 3-D printed. A method for attaching these filaments to commercial thermal ionization post assemblies has been devised. Resistive heating of the graphene based filaments under high vacuum showed stable operation in excess of 4 hours. Plutonium ion production has been observed in an initial set of filaments spiked with the Pu 128 Certified Reference Material.

  6. Molecular tools for the construction of peptide-based materials.

    Science.gov (United States)

    Ramakers, B E I; van Hest, J C M; Löwik, D W P M

    2014-04-21

    Proteins and peptides are fundamental components of living systems where they play crucial roles at both functional and structural level. The versatile biological properties of these molecules make them interesting building blocks for the construction of bio-active and biocompatible materials. A variety of molecular tools can be used to fashion the peptides necessary for the assembly of these materials. In this tutorial review we shall describe five of the main techniques, namely solid phase peptide synthesis, native chemical ligation, Staudinger ligation, NCA polymerisation, and genetic engineering, that have been used to great effect for the construction of a host of peptide-based materials.

  7. Geometric optimization of cross-flow heat exchanger based on dynamic controllability

    Directory of Open Access Journals (Sweden)

    Alotaibi Sorour

    2008-01-01

    Full Text Available The operation of heat exchangers and other thermal equipments in the face of variable loads is usually controlled by manipulating inlet fluid temperatures or mass flow rates, where the controlled variable is usually one of the output temperatures. The aim of this work is to optimize the geometry of a tube with internal flow of water and an external cross-flow of air, based on its controllability characteristics. Controllability is a useful concept both from theoretical and practical perspective since it tells us if a particular output can be controlled by a particular input. This concept can also provide us with information about the easiest operating condition to control a particular output. A transient model of a tube in cross-flow is developed, where an implicit formulation is used for transient numerical solutions. The aspect ratio of the tube is optimized, subject to volume constraints, based on the optimum operation in terms of controllability. The reported optimized aspect ratio, water mass flow rate and controllability are studied for deferent external properties of the tube.

  8. Crosslinked anion exchange membranes with primary diamine-based crosslinkers for vanadium redox flow battery application

    Science.gov (United States)

    Cha, Min Suc; Jeong, Hwan Yeop; Shin, Hee Young; Hong, Soo Hyun; Kim, Tae-Ho; Oh, Seong-Geun; Lee, Jang Yong; Hong, Young Taik

    2017-09-01

    A series of polysulfone-based crosslinked anion exchange membranes (AEMs) with primary diamine-based crosslinkers has been prepared via simple a crosslinking process as low-cost and durable membranes for vanadium redox flow batteries (VRFBs). Chloromethylated polysulfone is used as a precursor polymer for crosslinked AEMs (CAPSU-x) with different degrees of crosslinking. Among the developed AEMs, CAPSU-2.5 shows outstanding dimensional stability and anion (Cl-, SO42-, and OH-) conductivity. Moreover, CAPSU-2.5 exhibits much lower vanadium ion permeability (2.72 × 10-8 cm2 min-1) than Nafion 115 (2.88 × 10-6 cm2 min-1), which results in an excellent coulombic efficiency of 100%. The chemical and operational stabilities of the membranes have been investigated via ex situ soaking tests in 0.1 M VO2+ solution and in situ operation tests for 100 cycles, respectively. The excellent chemical, physical, and electrochemical properties of the CAPSU-2.5 membrane make it suitable for use in VRFBs.

  9. Patients' Data Management System Protected by Identity-Based Authentication and Key Exchange.

    Science.gov (United States)

    Rivero-García, Alexandra; Santos-González, Iván; Hernández-Goya, Candelaria; Caballero-Gil, Pino; Yung, Moti

    2017-03-31

    A secure and distributed framework for the management of patients' information in emergency and hospitalization services is proposed here in order to seek improvements in efficiency and security in this important area. In particular, confidentiality protection, mutual authentication, and automatic identification of patients are provided. The proposed system is based on two types of devices: Near Field Communication (NFC) wristbands assigned to patients, and mobile devices assigned to medical staff. Two other main elements of the system are an intermediate server to manage the involved data, and a second server with a private key generator to define the information required to protect communications. An identity-based authentication and key exchange scheme is essential to provide confidential communication and mutual authentication between the medical staff and the private key generator through an intermediate server. The identification of patients is carried out through a keyed-hash message authentication code. Thanks to the combination of the aforementioned tools, a secure alternative mobile health (mHealth) scheme for managing patients' data is defined for emergency and hospitalization services. Different parts of the proposed system have been implemented, including mobile application, intermediate server, private key generator and communication channels. Apart from that, several simulations have been performed, and, compared with the current system, significant improvements in efficiency have been observed.

  10. Patients’ Data Management System Protected by Identity-Based Authentication and Key Exchange

    Directory of Open Access Journals (Sweden)

    Alexandra Rivero-García

    2017-03-01

    Full Text Available A secure and distributed framework for the management of patients’ information in emergency and hospitalization services is proposed here in order to seek improvements in efficiency and security in this important area. In particular, confidentiality protection, mutual authentication, and automatic identification of patients are provided. The proposed system is based on two types of devices: Near Field Communication (NFC wristbands assigned to patients, and mobile devices assigned to medical staff. Two other main elements of the system are an intermediate server to manage the involved data, and a second server with a private key generator to define the information required to protect communications. An identity-based authentication and key exchange scheme is essential to provide confidential communication and mutual authentication between the medical staff and the private key generator through an intermediate server. The identification of patients is carried out through a keyed-hash message authentication code. Thanks to the combination of the aforementioned tools, a secure alternative mobile health (mHealth scheme for managing patients’ data is defined for emergency and hospitalization services. Different parts of the proposed system have been implemented, including mobile application, intermediate server, private key generator and communication channels. Apart from that, several simulations have been performed, and, compared with the current system, significant improvements in efficiency have been observed.

  11. Patients’ Data Management System Protected by Identity-Based Authentication and Key Exchange

    Science.gov (United States)

    Rivero-García, Alexandra; Santos-González, Iván; Hernández-Goya, Candelaria; Caballero-Gil, Pino; Yung, Moti

    2017-01-01

    A secure and distributed framework for the management of patients’ information in emergency and hospitalization services is proposed here in order to seek improvements in efficiency and security in this important area. In particular, confidentiality protection, mutual authentication, and automatic identification of patients are provided. The proposed system is based on two types of devices: Near Field Communication (NFC) wristbands assigned to patients, and mobile devices assigned to medical staff. Two other main elements of the system are an intermediate server to manage the involved data, and a second server with a private key generator to define the information required to protect communications. An identity-based authentication and key exchange scheme is essential to provide confidential communication and mutual authentication between the medical staff and the private key generator through an intermediate server. The identification of patients is carried out through a keyed-hash message authentication code. Thanks to the combination of the aforementioned tools, a secure alternative mobile health (mHealth) scheme for managing patients’ data is defined for emergency and hospitalization services. Different parts of the proposed system have been implemented, including mobile application, intermediate server, private key generator and communication channels. Apart from that, several simulations have been performed, and, compared with the current system, significant improvements in efficiency have been observed. PMID:28362328

  12. Injectable and Self-Healing Dynamic Hydrogels Based on Metal(I)-Thiolate/Disulfide Exchange as Biomaterials with Tunable Mechanical Properties.

    Science.gov (United States)

    Casuso, Pablo; Odriozola, Ibon; Pérez-San Vicente, Adrián; Loinaz, Iraida; Cabañero, Germán; Grande, Hans-Jürgen; Dupin, Damien

    2015-11-09

    Despite numerous strategies involving dynamic covalent bonds to produce self-healing hydrogels with similar frequency-dependent stiffness to native tissues, it remains challenging to use biologically relevant thiol/disulfide exchange to confer such properties to polymeric networks. Herein, we report a new method based on Metal(I) [Au(I) or Ag(I)] capping to protect thiolates from aerial oxidation without preventing thiolate/disulfide exchange. Dynamic hydrogels were readily prepared by injecting simultaneously aqueous solutions of commercially available HAuCl4 and 4-arm thiol-terminated polyethylene glycol [(PEGSH)4], resulting in a network containing a mixture of Au(I)-thiolate (Au-S) and disulfide bonds (SS). While the dynamic properties of the hydrogel were closely dependent on the pH, the mechanical properties could be easily tuned by adjusting (PEGSH)4 concentration and amount of Au-S, as judged by dynamic rheology studies. Permanent Au-S/SS exchange at physiological pH conferred self-healing behavior and frequency-dependent stiffness to the hydrogel. In addition, in vitro studies confirmed that Au-based dynamic material was not cytotoxic to human dermal fibroblasts, demonstrating its potential use as a medical device. Dynamic hydrogels obtained using Ag(I) ions demonstrated that the exchange reaction was not affected by the nature of the Metal(I) capping. Finally, this efficient thiolate capping strategy offers a simple way to produce injectable and self-healing dynamic hydrogels from virtually any thiol-containing polymers.

  13. Non-noble metal based electro-catalyst compositions for proton exchange membrane based water electrolysis and methods of making

    Science.gov (United States)

    Kumta, Prashant N.; Kadakia, Karan Sandeep; Datta, Moni Kanchan; Velikokhatnyi, Oleg

    2017-02-07

    The invention provides electro-catalyst compositions for an anode electrode of a proton exchange membrane-based water electrolysis system. The compositions include a noble metal component selected from the group consisting of iridium oxide, ruthenium oxide, rhenium oxide and mixtures thereof, and a non-noble metal component selected from the group consisting of tantalum oxide, tin oxide, niobium oxide, titanium oxide, tungsten oxide, molybdenum oxide, yttrium oxide, scandium oxide, cooper oxide, zirconium oxide, nickel oxide and mixtures thereof. Further, the non-noble metal component can include a dopant. The dopant can be at least one element selected from Groups III, V, VI and VII of the Periodic Table. The compositions can be prepared using a surfactant approach or a sol gel approach. Further, the compositions are prepared using noble metal and non-noble metal precursors. Furthermore, a thin film containing the compositions can be deposited onto a substrate to form the anode electrode.

  14. The tissue microarray data exchange specification: A community-based, open source tool for sharing tissue microarray data

    Directory of Open Access Journals (Sweden)

    Edgerton Mary E

    2003-05-01

    Full Text Available Abstract Background Tissue Microarrays (TMAs allow researchers to examine hundreds of small tissue samples on a single glass slide. The information held in a single TMA slide may easily involve Gigabytes of data. To benefit from TMA technology, the scientific community needs an open source TMA data exchange specification that will convey all of the data in a TMA experiment in a format that is understandable to both humans and computers. A data exchange specification for TMAs allows researchers to submit their data to journals and to public data repositories and to share or merge data from different laboratories. In May 2001, the Association of Pathology Informatics (API hosted the first in a series of four workshops, co-sponsored by the National Cancer Institute, to develop an open, community-supported TMA data exchange specification. Methods A draft tissue microarray data exchange specification was developed through workshop meetings. The first workshop confirmed community support for the effort and urged the creation of an open XML-based specification. This was to evolve in steps with approval for each step coming from the stakeholders in the user community during open workshops. By the fourth workshop, held October, 2002, a set of Common Data Elements (CDEs was established as well as a basic strategy for organizing TMA data in self-describing XML documents. Results The TMA data exchange specification is a well-formed XML document with four required sections: 1 Header, containing the specification Dublin Core identifiers, 2 Block, describing the paraffin-embedded array of tissues, 3Slide, describing the glass slides produced from the Block, and 4 Core, containing all data related to the individual tissue samples contained in the array. Eighty CDEs, conforming to the ISO-11179 specification for data elements constitute XML tags used in the TMA data exchange specification. A set of six simple semantic rules describe the complete data exchange

  15. Strength properties of fly ash based controlled low strength materials.

    Science.gov (United States)

    Türkel, S

    2007-08-25

    Controlled low strength material (CLSM) is a flowable mixture that can be used as a backfill material in place of compacted soils. Flowable fill requires no tamping or compaction to achieve its strength and typically has a load carrying capacity much higher than compacted soils, but it can still be excavated easily. The selection of CLSM type should be based on technical and economical considerations for specific applications. In this study, a mixture of high volume fly ash (FA), crushed limestone powder (filler) and a low percentage of pozzolana cement have been tried in different compositions. The amount of pozzolana cement was kept constant for all mixes as, 5% of fly ash weight. The amount of mixing water was chosen in order to provide optimum pumpability by determining the spreading ratio of CLSM mixtures using flow table method. The shear strength of the material is a measure of the materials ability to support imposed stresses on the material. The shear strength properties of CLSM mixtures have been investigated by a series of laboratory tests. The direct shear test procedure was applied for determining the strength parameters Phi (angle of shearing resistance) and C(h) (cohesion intercept) of the material. The test results indicated that CLSM mixtures have superior shear strength properties compared to compacted soils. Shear strength, cohesion intercept and angle of shearing resistance values of CLSM mixtures exceeded conventional soil materials' similar properties at 7 days. These parameters proved that CLSM mixtures are suitable materials for backfill applications.

  16. National Materials Property Data Network: standardization for materials-property data bases and networking

    Energy Technology Data Exchange (ETDEWEB)

    Kaufman, J.G.

    1986-02-01

    There are a number of hurdles to developing the National Materials Property Data Network (MPD Network), which will provide ready on-line access to computerized numeric research and engineering data on materials properties. The author reviews several studies carried out by the ASTM Society and others aimed at developing standards for developing sophisticated network software. He describes the need for standards of material designations, test methods, and data presentation, as well as ASTM's role in the process. ASTM intends to reinforce its position of having the highest caliber products in the field by becoming the leader in standards for materials property data base building and management. 29 references, 1 table.

  17. SYNTHESIS of MOLECULE/POLYMER-BASED MAGNETIC MATERIALS

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Joel S. [Univ. of Utah, Salt Lake City, UT (United States)

    2016-02-01

    We have synthesized and characterized several families of organic-based magnets, a new area showing that organic species can exhibit the technologically important property of magnetic ordering. Thin film magnets with ordering temperatures exceeding room temperature have been exceeded. Hence, organic-based magnets represent a new class of materials that exhibit magnetic ordering and do not require energy-intensive metallurgical processing and are based upon Earth-abundant elements.

  18. Design, integration and control of proton exchange membrane electrolyzer for wind based renewable energy applications

    Science.gov (United States)

    Harrison, Kevin W.

    This research endeavor began with the design and construction of a new hydrogen test facility at the National Renewable Energy Laboratory (NREL). To improve the electrical link of wind-based electrolysis the characterization of a proton exchange membrane (PEM) electrolyzer under varying input power was performed at NRELs new test facility. The commercially available electrolyzer from Proton Energy Systems (PES) was characterized using constant direct current (DC), sinusoidally varying DC, photovoltaics and variable magnitude and frequency energy from a 10 kW wind turbine. At rated stack current and ˜ 40°C the system efficiency of the commercial electrolyzer was measured to be 55%. At lower stack current it was shown that commercial electrolyzer system efficiency falls because of the continuous hydrogen purge (˜0.1 Nm3 hr-1) used to maintain the hydrogen desiccant drying system. A novel thermoelectric-based dew point controller is designed and modeled to reduce the penalty to renewable sources because they do not always operate at 100% of rated stack current. It is predicted that the thermoelectric design when operated 100% of the time at full current to the thermoelectric modules would consume 3.1 kWh kg -1 of hydrogen. Using the higher heating value of hydrogen and a stack efficiency of 60% to produce the hydrogen that is continuously vented, the desiccant system consumes about 5.7 kWh kg-1. Design of the UND electrolyzer sub-systems responsible for all aspects of water, power to the stack, and hydrogen conditioning enables more flexible and precise experimental data to be obtained than from an off-the-shelf system. Current-voltage (IV) characteristic curves were obtained on the UND system at temperatures between 7--70°C. The anode and cathode exchange current densities are fitted to 2.0 E-06 e0.043T and 0.12 e 0.026T A cm-2 respectively. Stack conductivity was fitted to 0.001T + 0.03 S cm-1. The three coefficients represent physical stack parameters and are

  19. QuakeML: status of the XML-based seismological data exchange format

    Directory of Open Access Journals (Sweden)

    Joachim Saul

    2011-04-01

    Full Text Available QuakeML is an XML-based data exchange standard for seismology that is in its fourth year of active community-driven development. Its development was motivated by the need to consolidate existing data formats for applications in statistical seismology, as well as setting a cutting-edge, community-agreed standard to foster interoperability of distributed infrastructures. The current release (version 1.2 is based on a public Request for Comments process and accounts for suggestions and comments provided by a broad international user community. QuakeML is designed as an umbrella schema under which several sub-packages are collected. The present scope of QuakeML 1.2 covers a basic description of seismic events including picks, arrivals, amplitudes, magnitudes, origins, focal mechanisms, and moment tensors. Work on additional packages (macroseismic information, ground motion, seismic inventory, and resource metadata has been started, but is at an early stage. Several applications based on the QuakeML data model have been created so far. Among these are earthquake catalog web services at the European Mediterranean Seismological Centre (EMSC, GNS Science, and the Southern California Earthquake Data Center (SCEDC, and QuakePy, an open-source Python-based seismicity analysis toolkit. Furthermore, QuakeML is being used in the SeisComP3 system from GFZ Potsdam, and in the Collaboratory for the Study of Earthquake Predictability (CSEP testing center installations, developed by Southern California Earthquake Center (SCEC. QuakeML is still under active and dynamic development. Further contributions from the community are crucial to its success and are highly welcome.

  20. Polymers Based on Renewable Raw Materials – Part II

    Directory of Open Access Journals (Sweden)

    Jovanović, S.

    2013-09-01

    Full Text Available A short review of biopolymers based on starch (starch derivatives, thermoplastic starch, lignin and hemicelluloses, chitin (chitosan and products obtained by degradation of starch and other polysaccharides and sugars (poly(lactic acid, poly(hydroxyalkanoates, as well as some of their basic properties and application area, are given in this part. The problem of environmental and economic feasibility of biopolymers based on renewable raw materials and their competitiveness with polymers based on fossil raw materials is discussed. Also pointed out are the problems that appear due to the increasing use of agricultural land for the production of raw materials for the chemical industry and energy, instead for the production of food for humans and animals. The optimistic assessments of experts considering the development perspectives of biopolymers based on renewable raw materials in the next ten years have also been pointed out.At the end of the paper, the success of a team of researchers gathered around the experts from the company Bayer is indicated. They were the first in the world to develop a catalyst by which they managed to effectively activate CO - and incorporate it into polyols, used for the synthesis of polyurethanes in semi-industrial scale. By applying this process, for the first time a pollutant will be used as a basic raw material for the synthesis of organic compounds, which will have significant consequences on the development of the chemical industry, and therefore the production of polymers.

  1. Interpretation of ongoing thermal response tests of vertical (BHE) borehole heat exchangers with predictive uncertainty based stopping criterion

    DEFF Research Database (Denmark)

    Poulsen, Søren Erbs; Alberdi Pagola, Maria

    2015-01-01

    A method for real-time interpretation of ongoing thermal response tests of vertical borehole heat exchangers is presented. The method utilizes a statistically based stopping criterion for ongoing tests. The study finds minimum testing times for synthetic and actual TRTs to be in the interval 12–2...

  2. Preparation and characterization of monovalent ion selective cation exchange membranes based on sulphonated poly(ether ether ketone)

    NARCIS (Netherlands)

    Balster, J.H.; Krupenko, O.; Krupenko, O.; Punt, Ineke G.M.; Stamatialis, Dimitrios; Wessling, Matthias

    2005-01-01

    This paper analyses the separation properties of various commercial cation exchange membranes (CEMs) and tailor made membranes based on sulphonated poly(ether ether ketone) and poly(ether sulphone) for binary electrolyte solutions containing protons and calcium ions. All membranes are thoroughly

  3. Acquisition of Picture Exchange-Based vs. Signed Mands and Implications to Teach Functional Communication Skills to Children with Autism

    Science.gov (United States)

    Nam, Sang S.; Hwang, Young S.

    2016-01-01

    A literature review was conducted to describe important concepts involved in functional analysis of verbal behavior as well as to evaluate empirical research findings on acquisition of picture exchange-based vs. signed mands to suggest instructional implications for teachers and therapists to teach functional communication skills to children with…

  4. Patient encounters and care transitions in one community supported by automated query-based health information exchange.

    Science.gov (United States)

    Campion, Thomas R; Vest, Joshua R; Ancker, Jessica S; Kaushal, Rainu

    2013-01-01

    Care transitions from one facility to another threaten patient safety due to the potential loss of critical clinical information. Electronic clinical data exchange may address the problem. Approaches to exchange range from manual directed exchange, or sending point-to-point messages, to automated query-based health information exchange (HIE), or aggregating data from multiple sources. In this study, we measured the extent to which automated query-based HIE supported patient encounters and care transitions in one community. During the 23-month study period, 41% (n=33,219) of affirmatively consented patients had at least one encounter supported by automated query-based HIE. Of these patients, 41% (n=13,685) visited two or more facilities and accounted for 68% of total encounters. Of total encounters, 28% (n=40,828) were care transitions from one facility to another. Findings suggest that automated query-based HIE may support care transitions with efficient information sharing and assist United States providers in achieving stage two of meaningful use.

  5. The use of graphene based materials for fuel cell, photovoltaics, and supercapacitor electrode materials

    Science.gov (United States)

    Tsang, Alpha C. H.; Kwok, Holly Y. H.; Leung, Dennis Y. C.

    2017-05-01

    This manuscript presents the methodology of the production of 2D and 3D graphene based material, and their applications in fuel cell, supercapacitor, and photovoltic in recent years. Due to the uniqueness and attractive properties of graphene nanosheets, a large number of techniques have been developed for raw graphene preparation, from a chemical method to a physical deposition of carbon vapor under extreme conditions. A variety of graphene based materials were also prepared from raw graphene or graphene oxide, including the metal loaded, metal oxides loaded, to the foreign elements doped graphene. Both two-dimensional (2D) to three-dimensional (3D) structured graphene were covered. These materials included the bulk or template hybrid composite, containing graphene hydrogel, graphene aerogel, or graphene foam and its derived products. They were widely used in green energy device research, which exhibited strong activity, and developed some special usage in recent research.

  6. Evaluation of a Passive Heat Exchanger Based Cooling System for Fuel Cell Applications

    Science.gov (United States)

    Colozza, Anthony J.; Burke, Kenneth A.

    2011-01-01

    Fuel cell cooling is conventionally performed with an actively controlled, dedicated coolant loop that exchanges heat with a separate external cooling loop. To simplify this system the concept of directly cooling a fuel cell utilizing a coolant loop with a regenerative heat exchanger to preheat the coolant entering the fuel cell with the coolant exiting the fuel cell was analyzed. The preheating is necessary to minimize the temperature difference across the fuel cell stack. This type of coolant system would minimize the controls needed on the coolant loop and provide a mostly passive means of cooling the fuel cell. The results indicate that an operating temperature of near or greater than 70 C is achievable with a heat exchanger effectiveness of around 90 percent. Of the heat exchanger types evaluated with the same type of fluid on the hot and cold side, a counter flow type heat exchanger would be required which has the possibility of achieving the required effectiveness. The number of heat transfer units required by the heat exchanger would be around 9 or greater. Although the analysis indicates the concept is feasible, the heat exchanger design would need to be developed and optimized for a specific fuel cell operation in order to achieve the high effectiveness value required.

  7. Additive Manufacturing of Ceramic Heat Exchanger: Opportunities and Limits of the Lithography-Based Ceramic Manufacturing (LCM)

    Science.gov (United States)

    Scheithauer, Uwe; Schwarzer, Eric; Moritz, Tassilo; Michaelis, Alexander

    2018-01-01

    Additive manufacturing (AM) techniques allow the preparation of tailor-made structures for specific applications with a high flexibility in regard to shape and design. The lithography-based ceramic manufacturing (LCM) technology allows the AM of high-performance alumina and zirconia components. There are still some restrictions in regard to possible geometries. The opportunities and limits of the LCM technology are discussed in the following paper using the example of ceramic heat exchangers. Structures are presented which combine a large surface for heat exchange with a small component volume and low pressure drop. This paper concludes summarizing the essential remarks.

  8. Willingness to Exchange Health Information via Mobile Devices: Findings From a Population-Based Survey.

    Science.gov (United States)

    Serrano, Katrina J; Yu, Mandi; Riley, William T; Patel, Vaishali; Hughes, Penelope; Marchesini, Kathryn; Atienza, Audie A

    2016-01-01

    The rapid proliferation of mobile devices offers unprecedented opportunities for patients and health care professionals to exchange health information electronically, but little is known about patients' willingness to exchange various types of health information using these devices. We examined willingness to exchange different types of health information via mobile devices, and assessed whether sociodemographic characteristics and trust in clinicians were associated with willingness in a nationally representative sample. We analyzed data for 3,165 patients captured in the 2013 Health Information National Trends Survey. Multinomial logistic regression analysis was conducted to test differences in willingness. Ordinal logistic regression analysis assessed correlates of willingness to exchange 9 types of information separately. Participants were very willing to exchange appointment reminders (odds ratio [OR] = 6.66; 95% CI, 5.68-7.81), general health tips (OR = 2.03; 95% CI, 1.74-2.38), medication reminders (OR = 2.73; 95% CI, 2.35-3.19), laboratory/test results (OR = 1.76; 95% CI, 1.62-1.92), vital signs (OR = 1.63; 95% CI, 1.48-1.80), lifestyle behaviors (OR = 1.40; 95% CI, 1.24-1.58), and symptoms (OR = 1.62; 95% CI, 1.46-1.79) as compared with diagnostic information. Older adults had lower odds of being more willing to exchange any type of information. Education, income, and trust in health care professional information correlated with willingness to exchange certain types of information. Respondents were less willing to exchange via mobile devices information that may be considered sensitive or complex. Age, socioeconomic factors, and trust in professional information were associated with willingness to engage in mobile health information exchange. Both information type and demographic group should be considered when developing and tailoring mobile technologies for patient-clinician communication. © 2016 Annals of Family Medicine, Inc.

  9. Carbon-based nanomaterials: multifunctional materials for biomedical engineering.

    Science.gov (United States)

    Cha, Chaenyung; Shin, Su Ryon; Annabi, Nasim; Dokmeci, Mehmet R; Khademhosseini, Ali

    2013-04-23

    Functional carbon-based nanomaterials (CBNs) have become important due to their unique combinations of chemical and physical properties (i.e., thermal and electrical conductivity, high mechanical strength, and optical properties), and extensive research efforts are being made to utilize these materials for various industrial applications, such as high-strength materials and electronics. These advantageous properties of CBNs are also actively investigated in several areas of biomedical engineering. This Perspective highlights different types of carbon-based nanomaterials currently used in biomedical applications.

  10. Recent Progress on PEDOT-Based Thermoelectric Materials

    Directory of Open Access Journals (Sweden)

    Qingshuo Wei

    2015-02-01

    Full Text Available The thermoelectric properties of poly(3,4-ethylenedioxythiophene (PEDOT-based materials have attracted attention recently because of their remarkable electrical conductivity, power factor, and figure of merit. In this review, we summarize recent efforts toward improving the thermoelectric properties of PEDOT-based materials. We also discuss thermoelectric measurement techniques and several unsolved problems with the PEDOT system such as the effect of water absorption from the air and the anisotropic thermoelectric properties. In the last part, we describe our work on improving the power output of thermoelectric modules by using PEDOT, and we outline the potential applications of polymer thermoelectric generators.

  11. Licensing web-based nursing programs, courses, and course materials.

    Science.gov (United States)

    Billings, Diane M; Hoke, Mary M; Waldhuetter, Kurt

    2005-01-01

    With the advent of the digital information age, schools of nursing are developing and using web-based programs, courses, and course materials to meet students' needs for access and high-quality learning experiences. In an attempt to maximize scant resources, including faculty, many schools are seeking grant funding, joining consortia, or forming partnerships that require sharing of web-based course materials. Entering such collaborative arrangements usually requires licensing agreements to transfer intellectual capital. This article explains licensing and the related concepts of intellectual property, copyright, and technology transfer. It also identifies the advantages and disadvantages of licensing and describes a licensing process.

  12. Water sorption and solubility of polyamide denture base materials.

    Science.gov (United States)

    Nguyen, Long G; Kopperud, Hilde M; Øilo, Marit

    2017-01-01

    Purpose: Some patients experience adverse reactions to poly(methyl methacrylate)-based (PMMA) dentures. Polyamide (PA) as an alternative to PMMA has, however, not been well documented with regard to water sorption and water solubility. The aim of this in vitro study was to measure water sorption and water solubility of two PA materials compared with PMMA, and to evaluate the major components released from the PA materials and the effect on hardness of the materials. Methods: Ten discs (40.0 mm diameter, 2.0 mm thick) of each material (PA: Valplast and Breflex; PMMA: SR Ivocap HIP) were prepared according to manufacturers' recommendations. The specimens were tested for water sorption and water solubility, according to a modification of ISO 20795-1:2008. Released substances were analysed by gas chromatography/mass spectrometry (GC/MS). Results: There were statistically significant differences among the materials regarding water sorption, water solubility and time to water saturation. Breflex had the highest water sorption (30.4 μg/mm(3)), followed by PMMA-material (25.8 μg/mm(3)) and Valplast (13.6 μg/mm(3)). Both PA materials had statistically significant lower water solubility than the PMMA. Both PA had a net increase in weight. Analysis by GC/MS identified release of the compound 12-aminododecanolactam from the material Valplast. No release was found from the Breflex material. Conclusions: The PA denture materials show differences in water sorption and solubility, but within the limits of the standard requirements. The PA showed a net increase in weight after long-term water sorption. The clinical implications of the findings are not elucidated.

  13. A potential base substrate for deformable scintillation materials

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Hidehito, E-mail: hidehito@rri.kyoto-u.ac.jp [Kyoto University, 2, Asashiro-Nishi, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan); National Institute of Radiological Sciences, 4-9-1, Anagawa, Inage-ku, Chiba-shi, Chiba 263-8555 (Japan); Sato, Nobuhiro [Kyoto University, 2, Asashiro-Nishi, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan); Kitamura, Hisashi [National Institute of Radiological Sciences, 4-9-1, Anagawa, Inage-ku, Chiba-shi, Chiba 263-8555 (Japan); Shirakawa, Yoshiyuki [Waseda University, 513, Waseda-Tsurumaki-cho, Shinjuku-ku, Tokyo 162-0041 (Japan); Takahashi, Sentaro [Kyoto University, 2, Asashiro-Nishi, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan)

    2016-05-11

    Deformable scintillation materials for radiation detection are an original concept that will impact many applications. Here we reveal the optical characteristics of readily available, transparent grease that consists of adhesive aromatic ring polymers. The aromatic ring polymer is methyl phenyl polysiloxane, commonly used in cosmetics, lubrication, heat conduction, and mechanical damping. It has a 285-nm excitation maximum and emits short wavelength light that peaks at 315 nm. The stopping power for 1 MeV electrons is 1.78 MeV cm{sup 2}/g. The light-yield distribution has distinct peaks at 976 keV from internal conversion electrons and at 5486 keV from alpha particles. In addition, this particular methyl phenyl polysiloxane is safe for use and disposal, which is an excellent advantage. These aromatic ring polymers are potential base substrates for deformable scintillation materials and make an important addition to the categories of scintillation materials. - Highlights: • Adhesive aromatic ring polymers can be deformable base substrates for scintillation materials. • Transparent grease consisting of methyl phenyl polysiloxane was characterised. • Short-wavelength light with a 315-nm emission maximum was emitted. • Distinct peaks induced by internal conversion electrons and alpha particles were observed in light-yield distributions. • Deformable scintillation materials are an original category of materials for radiation detection.

  14. Model-based high-throughput design of ion exchange protein chromatography.

    Science.gov (United States)

    Khalaf, Rushd; Heymann, Julia; LeSaout, Xavier; Monard, Florence; Costioli, Matteo; Morbidelli, Massimo

    2016-08-12

    This work describes the development of a model-based high-throughput design (MHD) tool for the operating space determination of a chromatographic cation-exchange protein purification process. Based on a previously developed thermodynamic mechanistic model, the MHD tool generates a large amount of system knowledge and thereby permits minimizing the required experimental workload. In particular, each new experiment is designed to generate information needed to help refine and improve the model. Unnecessary experiments that do not increase system knowledge are avoided. Instead of aspiring to a perfectly parameterized model, the goal of this design tool is to use early model parameter estimates to find interesting experimental spaces, and to refine the model parameter estimates with each new experiment until a satisfactory set of process parameters is found. The MHD tool is split into four sections: (1) prediction, high throughput experimentation using experiments in (2) diluted conditions and (3) robotic automated liquid handling workstations (robotic workstation), and (4) operating space determination and validation. (1) Protein and resin information, in conjunction with the thermodynamic model, is used to predict protein resin capacity. (2) The predicted model parameters are refined based on gradient experiments in diluted conditions. (3) Experiments on the robotic workstation are used to further refine the model parameters. (4) The refined model is used to determine operating parameter space that allows for satisfactory purification of the protein of interest on the HPLC scale. Each section of the MHD tool is used to define the adequate experimental procedures for the next section, thus avoiding any unnecessary experimental work. We used the MHD tool to design a polishing step for two proteins, a monoclonal antibody and a fusion protein, on two chromatographic resins, in order to demonstrate it has the ability to strongly accelerate the early phases of process

  15. Novel proton exchange membrane based on crosslinked poly(vinyl alcohol) for direct methanol fuel cells

    Science.gov (United States)

    Liu, Chien-Pan; Dai, Chi-An; Chao, Chi-Yang; Chang, Shoou-Jinn

    2014-03-01

    In this study, we report the synthesis and the characterization of poly (vinyl alcohol) based proton conducting membranes. In particular, we describe a novel physically and chemically PVA/HFA (poly (vinyl alcohol)/hexafluoroglutaric acid) blending membranes with BASANa (Benzenesulfonic acid sodium salt) and GA (Glutaraldehyde) as binary reaction agents. The key PEM parameters such as ion exchange capacity (IEC), water uptake, proton conductivity, and methanol permeability were controlled by adjusting the chemical composition of the membranes. The IEC value of the membrane is found to be an important parameter in affecting water uptake, conductivity as well as the permeability of the resulting membrane. Plots of the water uptake, conductivity, and methanol permeability vs. IEC of the membranes show a distinct change in the slope of their curves at roughly the same IEC value which suggests a transition of structural changes in the network. The proton conductivities and the methanol permeability of all the membranes are in the range of 10-3-10-2 S cm-1 and 10-8-10-7 cm2 s-1, respectively, depending on its binary crosslinking density, and it shows great selectivity compared with those of Nafion®-117. The membranes display good mechanical properties which suggest a good lifetime usage of the membranes applied in DMFCs.

  16. Prognostics of Proton Exchange Membrane Fuel Cells stack using an ensemble of constraints based connectionist networks

    Science.gov (United States)

    Javed, Kamran; Gouriveau, Rafael; Zerhouni, Noureddine; Hissel, Daniel

    2016-08-01

    Proton Exchange Membrane Fuel Cell (PEMFC) is considered the most versatile among available fuel cell technologies, which qualify for diverse applications. However, the large-scale industrial deployment of PEMFCs is limited due to their short life span and high exploitation costs. Therefore, ensuring fuel cell service for a long duration is of vital importance, which has led to Prognostics and Health Management of fuel cells. More precisely, prognostics of PEMFC is major area of focus nowadays, which aims at identifying degradation of PEMFC stack at early stages and estimating its Remaining Useful Life (RUL) for life cycle management. This paper presents a data-driven approach for prognostics of PEMFC stack using an ensemble of constraint based Summation Wavelet- Extreme Learning Machine (SW-ELM) models. This development aim at improving the robustness and applicability of prognostics of PEMFC for an online application, with limited learning data. The proposed approach is applied to real data from two different PEMFC stacks and compared with ensembles of well known connectionist algorithms. The results comparison on long-term prognostics of both PEMFC stacks validates our proposition.

  17. Quaternized dimethylaminoethyl methacrylate strong base anion exchange fibers for As(V) adsorption

    Science.gov (United States)

    Kavaklı, Cengiz; Akkaş Kavaklı, Pınar; Turan, Burcu Dila; Hamurcu, Aslı; Güven, Olgun

    2014-09-01

    N,N-Dimethylaminoethyl methacrylate (DMAEMA) grafted polyethylene/polypropylene (PE/PP) nonwoven fibers (DMAEMA-g-PE/PP) was prepared by radiation-induced graft polymerization. DMAEMA graft chains on nonwoven fibers were quaternized with dimethyl sulfate solution for the preparation of strong base anion exchange fibers (QDMAEMA-g-PE/PP). Fiber structures were characterized by FTIR, XPS and SEM techniques. The effect of solution pH, contact time, initial As(V) ion concentration and coexisting ions on the As(V) adsorption capacity of the QDMAEMA-g-PE/PP fibers were investigated by performing batch adsorption experiments. The adsorption of As(V) by QDMAEMA-g-PE/PP fibers was found to be independent on solution pH in the range 4.00-10.00. Kinetic experiments show that the As(V) adsorption rate was rapid and As(V) adsorption follows pseudo second-order kinetic model. As(V) adsorption equilibrium data were analyzed using Langmuir and Freundlich adsorption isotherm model equations. Langmuir and Freundlich adsorption isotherm models fitted the experimental data well. The maximum adsorption capacity (qmax) calculated from Langmuir isotherm was found to be 83.33 mg As(V)/g polymer at pH 7.00. The adsorbent was used for three cycles without significant loss of adsorption capacity. The adsorbed As(V) ions were desorbed effectively by a 0.1 M NaOH solution.

  18. Nanotechnology-based restorative materials for dental caries management.

    Science.gov (United States)

    Melo, Mary A S; Guedes, Sarah F F; Xu, Hockin H K; Rodrigues, Lidiany K A

    2013-08-01

    Nanotechnology has been applied to dental materials as an innovative concept for the development of materials with better properties and anticaries potential. In this review we discuss the current progress and future applications of functional nanoparticles incorporated in dental restorative materials as useful strategies to dental caries management. We also overview proposed antimicrobial and remineralizing mechanisms. Nanomaterials have great potential to decrease biofilm accumulation, inhibit the demineralization process, to be used for remineralizing tooth structure, and to combat caries-related bacteria. These results are encouraging and open the doors to future clinical studies that will allow the therapeutic value of nanotechnology-based restorative materials to be established. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. Thermotropic and Thermochromic Polymer Based Materials for Adaptive Solar Control

    Directory of Open Access Journals (Sweden)

    Olaf Mühling

    2010-12-01

    Full Text Available The aim of this review is to present the actual status of development in adaptive solar control by use of thermotropic and organic thermochromic materials. Such materials are suitable for application in smart windows. In detail polymer blends, hydrogels, resins, and thermoplastic films with a reversible temperature-dependent switching behavior are described. A comparative evaluation of the concepts for these energy efficient materials is given as well. Furthermore, the change of strategy from ordinary shadow systems to intrinsic solar energy reflection materials based on phase transition components and a first remark about their realization is reported. Own current results concerning extruded films and high thermally stable casting resins with thermotropic properties make a significant contribution to this field.

  20. Using learning materials for design-based interventions

    DEFF Research Database (Denmark)

    Gissel, Stig Toke

    2015-01-01

    This article considers a methodological issue concerning the use of learning materials for interventions in design-based research. When the researcher uses existing or creates new didacticised learning materials for research purposes and tests their applicability in authentic contexts, many...... variables are in play. When using or designing a learning material a lot of choices have to be made and effects are difficult to isolate. The advantage of using learning materials for interventions is that results could have high ecological validity. In the article this methodological issue is exemplified....... This issue is very important in general – and a subject of controversy. It is argued that the choice of texts depends on which theory of reading and which definition of readability are used, which in turn depends on the design for learning and the scaffolding which frames the student’s encounter...

  1. Comparison of the performance of exact-exchange-based density functional methods.

    Science.gov (United States)

    Liu, Fenglai; Proynov, Emil; Yu, Jian-Guo; Furlani, Thomas R; Kong, Jing

    2012-09-21

    How to describe nondynamic electron correlation is still a major challenge to density functional theory (DFT). Recent models designed particularly for this problem, such as Becke'05 (B05) and Perdew-Staroverov-Tao-Scuseria (PSTS) functionals employ the exact-exchange density, the efficient calculation of which is technically quite challenging. We have recently implemented self-consistently the B05 functional based on an efficient resolution-identity (RI) technique. In this study, we report a self-consistent RI implementation of the PSTS functional. In contrast to its original implementation, our version brings no limitation on the choice of the basis set. We have also implemented the Mori-Sanchez-Cohen-Yang-2 (MCY2) functional, another recent DFT method that includes full exact exchange. The performance of PSTS, B05, and MCY2 is validated on thermochemistry, reaction barriers, and dissociation energy curves, with an emphasis on nondynamic correlation effects in the discussion. All three methods perform rather well in general, B05 and MCY2 being on average somewhat better than PSTS. We include also results with other functionals that represent various aspects of the development in this field in recent years, including B3LYP, M06-HF, M06-2X, ωB97X, and TPSSh. The performance of the heavy-parameterized functionals M06-2X and ωB97X is on average better than that of B05, MCY2, and PSTS for standard thermodynamic properties and reactions, while the latter functionals do better in hydrogen abstraction reactions and dissociation processes. In particular, B05 is found to be the only functional that yields qualitatively correct dissociation curves for two-center symmetric radicals like He(2)(+). Finally, we compare the performance of all these functionals on a strongly correlated exemplary case system, the NO dimer. Only PSTS, B05, and MCY2 describe the system qualitatively correctly. Overall, this new type of functionals show good promise of overcoming some of the

  2. An intervention to help community-based organizations implement an evidence-based HIV prevention intervention: the Mpowerment Project technology exchange system.

    Science.gov (United States)

    Kegeles, Susan M; Rebchook, Gregory; Pollack, Lance; Huebner, David; Tebbetts, Scott; Hamiga, John; Sweeney, David; Zovod, Benjamin

    2012-03-01

    Considerable resources have been spent developing and rigorously testing HIV prevention intervention models, but such models do not impact the AIDS pandemic unless they are implemented effectively by community-based organizations (CBOs) and health departments. The Mpowerment Project (MP) is being implemented by CBOs around the U.S. It is a multilevel, evidence-based HIV prevention program for young gay/bisexual men that targets individual, interpersonal, social, and structural issues by using empowerment and community mobilization methods. This paper discusses the development of an intervention to help CBOs implement the MP called the Mpowerment Project Technology Exchange System (MPTES); CBOs' uptake, utilization and perceptions of the MPTES components; and issues that arose during technical assistance. The seven-component MPTES was provided to 49 CBOs implementing the MP that were followed longitudinally for up to two years. Except for the widely used program manual, other program materials were used early in implementing the MP and then their use declined. In contrast, once technical assistance was proactively provided, its usage remained constant over time, as did requests for technical assistance. CBOs expressed substantial positive feedback about the MPTES, but felt that it needs more focus on diversity issues, describing real world implementation approaches, and providing guidance on how to adapt the MP to diverse populations.

  3. Evaluation of web-based osteoporosis educational materials.

    Science.gov (United States)

    Wallace, Lorraine S; Turner, Lori W; Ballard, Joyce E; Keenum, Amy J; Weiss, Barry D

    2005-12-01

    Many women are unaware of risk factors for and consequences of osteoporosis. Hence, patient education is an essential step in preventing and managing osteoporosis. Unfortunately, numerous studies have demonstrated a mismatch between the reading difficulty of typical patient education materials and the reading ability of many American adults. We examined the readability and quality of web-based information on osteoporosis using the Suitability Assessment of Materials (SAM) and DISCERN instruments. The three most widely used Internet search engines, Google, Yahoo, and MSN, were selected based on popularity according to Nielsen/Net Ratings. The search term osteoporosis was entered to generate the first 30 websites listed by each of the three search engines. Several websites appeared on all three search engines; we identified 27 unique websites. Overall, 51.9% of materials were rated by the SAM as not suitable. Most materials scored poorly for their reading level (82.6% were rated not suitable), with an average reading level at grade 11.5 +/- 2.8. The mean DISCERN score for overall description of treatment options was 35.7 +/- 18.0, indicating inadequate quality. Most materials had low quality in a number of indicators, including accuracy and biased presentation of information. Web-based osteoporosis information is written above the reading ability of most American adults, and much of it lacks adequate quality.

  4. Polyazulene based materials for heavy metal ions detection

    Science.gov (United States)

    Oprisanu, A.; Ungureanu, E. M.; Isopescu, R.; Birzan, L.; Mihai, M.; Vasiliu, C.

    2017-06-01

    Azulene is a special monomer used to functionalize electrodes, due to its spontaneous electron drift from the seven-membered ring to the five-membered ring. The seven-membered ring of the molecule may act as electron acceptor, while the five-membered ring - as electron donor. This leads to very attractive properties for the synthesis of functional advanced materials like: materials with nonlinear optical and photorefractive properties, cathode materials for lithium batteries, or light emitting diodes based on organic materials. Azulene derivatives have been used rarely to the metal ions electroanalysis. Our study concerns the synthesis and electrochemical characterization of a new azulene based monomer 4-(azulen-1-yl)-2,6-bis((E)-2-(thiophen-3-yl)vinyl)pyridine (L). L has been used to obtain modified electrodes by electrochemical polymerization. PolyL films modified electrodes have been characterized by cyclic voltammetry in ferrocene solutions. The complexing properties of polyL based functional materials have been investigated towards heavy metals (Pb, Cd Hg, Cu) by preconcentration - anodic stripping technique in order to analyze the content of these cations from water samples.

  5. Carbon-Nanotube-Based Thermoelectric Materials and Devices

    Energy Technology Data Exchange (ETDEWEB)

    Blackburn, Jeffrey L. [Chemistry and Nanoscience Center, National Renewable Energy Laboratory, Golden CO 80401-3305 USA; Ferguson, Andrew J. [Chemistry and Nanoscience Center, National Renewable Energy Laboratory, Golden CO 80401-3305 USA; Cho, Chungyeon [Department of Mechanical Engineering, Texas A& M University, College Station TX 77843-3003 USA; Grunlan, Jaime C. [Department of Mechanical Engineering, Texas A& M University, College Station TX 77843-3003 USA

    2018-01-22

    Conversion of waste heat to voltage has the potential to significantly reduce the carbon footprint of a number of critical energy sectors, such as the transportation and electricity-generation sectors, and manufacturing processes. Thermal energy is also an abundant low-flux source that can be harnessed to power portable/wearable electronic devices and critical components in remote off-grid locations. As such, a number of different inorganic and organic materials are being explored for their potential in thermoelectric-energy-harvesting devices. Carbon-based thermoelectric materials are particularly attractive due to their use of nontoxic, abundant source-materials, their amenability to high-throughput solution-phase fabrication routes, and the high specific energy (i.e., W g-1) enabled by their low mass. Single-walled carbon nanotubes (SWCNTs) represent a unique 1D carbon allotrope with structural, electrical, and thermal properties that enable efficient thermoelectric-energy conversion. Here, the progress made toward understanding the fundamental thermoelectric properties of SWCNTs, nanotube-based composites, and thermoelectric devices prepared from these materials is reviewed in detail. This progress illuminates the tremendous potential that carbon-nanotube-based materials and composites have for producing high-performance next-generation devices for thermoelectric-energy harvesting.

  6. Carbon-Nanotube-Based Thermoelectric Materials and Devices.

    Science.gov (United States)

    Blackburn, Jeffrey L; Ferguson, Andrew J; Cho, Chungyeon; Grunlan, Jaime C

    2018-01-22

    Conversion of waste heat to voltage has the potential to significantly reduce the carbon footprint of a number of critical energy sectors, such as the transportation and electricity-generation sectors, and manufacturing processes. Thermal energy is also an abundant low-flux source that can be harnessed to power portable/wearable electronic devices and critical components in remote off-grid locations. As such, a number of different inorganic and organic materials are being explored for their potential in thermoelectric-energy-harvesting devices. Carbon-based thermoelectric materials are particularly attractive due to their use of nontoxic, abundant source-materials, their amenability to high-throughput solution-phase fabrication routes, and the high specific energy (i.e., W g -1 ) enabled by their low mass. Single-walled carbon nanotubes (SWCNTs) represent a unique 1D carbon allotrope with structural, electrical, and thermal properties that enable efficient thermoelectric-energy conversion. Here, the progress made toward understanding the fundamental thermoelectric properties of SWCNTs, nanotube-based composites, and thermoelectric devices prepared from these materials is reviewed in detail. This progress illuminates the tremendous potential that carbon-nanotube-based materials and composites have for producing high-performance next-generation devices for thermoelectric-energy harvesting. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Polymerization shrinkage of flowable resin-based restorative materials.

    Science.gov (United States)

    Stavridakis, Minos M; Dietschi, Didier; Krejci, Ivo

    2005-01-01

    This study measured the linear polymerization displacement and polymerization forces induced by polymerization shrinkage of a series of flowable resin-based restorative materials. The materials tested were 22 flowable resin-based restorative materials (Admira Flow, Aelite Flow, Aeliteflow LV, Aria, Crystal Essence, Definite Flow, Dyract Flow, Filtek Flow, FloRestore, Flow-it, Flow-Line, Freedom, Glacier, OmegaFlo, PermaFlo, Photo SC, Revolution 2, Star Flow, Synergy Flow, Tetric Flow, Ultraseal XT and Wave). Measurements for linear polymerization displacement and polymerization forces were performed using custom made measuring devices. Polymerization of the test materials was carried out for 60 seconds by means of a light curing unit, and each property was measured for 180 seconds from the start of curing in eight specimens for each material. Statistical evaluation of the data was performed with one-way analysis of variance (ANOVA), Tukey's Studentized Range (HSD) test (p=0.05) and simple linear regression. A wide range of values was recorded for linear polymerization displacement (26.61 to 80.74 microns) and polymerization forces (3.23 to 7.48 kilograms). Statistically significant differences among materials were found for both properties studied. Very few materials (Freedom, Glacier, and Photo SC) presented low values of linear polymerization displacement and polymerization forces (similar to hybrid resin composites), while the majority of materials presented very high values in both properties studied. Study of the shrinkage kinetics revealed the exponential growth process of both properties. The polymerization forces development exhibited a few seconds delay over linear polymerization displacement. Simple linear regression showed that the two polymerization shrinkage properties that were studied were not highly correlated (r2=0.59).

  8. Biases of Professional Exchange Rate Forecasts: Psychological Explanations and an Experimentally-Based Comparison to Novices

    OpenAIRE

    Bofinger, Peter; Leitner, Johannes; Schmidt, Robert

    2004-01-01

    The empirical performance of macroeconomic exchange rate models is more than disappointing. This dismal result is also reflected in the forecasting capabilities of professional analysts: all in all, analysts are not in a position to beat naïve random walk forecasts. The root for this deficient outcome stems from the fact that professional forecasts are to a large extend influenced by actual changes in exchange rates. A reasonable explanation for this behaviour can be taken from the behavioura...

  9. High Thermal Conductivity Polymer Composites for Low Cost Heat Exchangers

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-08-01

    This factsheet describes a project that identified and evaluated commercially available and state-of-the-art polymer-based material options for manufacturing industrial and commercial non-metallic heat exchangers. A heat exchanger concept was also developed and its performance evaluated with heat transfer modeling tools.

  10. Quantitative analysis of lead in polysulfide-based impression material

    Directory of Open Access Journals (Sweden)

    Aparecida Silva Braga

    2007-06-01

    Full Text Available Permlastic® is a polysulfide-based impression material widely used by dentists in Brazil. It is composed of a base paste and a catalyzer containing lead dioxide. The high toxicity of lead to humans is ground for much concern, since it can attack various systems and organs. The present study involved a quantitative analysis of the concentration of lead in the material Permlastic®. The lead was determined by plasma-induced optical emission spectrometry (Varian model Vista. The percentages of lead found in the two analyzed lots were 38.1 and 40.8%. The lead concentrations in the material under study were high, but the product’s packaging contained no information about these concentrations.

  11. Plasma deposition of amorphous silicon-based materials

    CERN Document Server

    Bruno, Giovanni; Madan, Arun

    1995-01-01

    Semiconductors made from amorphous silicon have recently become important for their commercial applications in optical and electronic devices including FAX machines, solar cells, and liquid crystal displays. Plasma Deposition of Amorphous Silicon-Based Materials is a timely, comprehensive reference book written by leading authorities in the field. This volume links the fundamental growth kinetics involving complex plasma chemistry with the resulting semiconductor film properties and the subsequent effect on the performance of the electronic devices produced. Key Features * Focuses on the plasma chemistry of amorphous silicon-based materials * Links fundamental growth kinetics with the resulting semiconductor film properties and performance of electronic devices produced * Features an international group of contributors * Provides the first comprehensive coverage of the subject, from deposition technology to materials characterization to applications and implementation in state-of-the-art devices.

  12. Ternary gypsum-based materials: Composition, properties and utilization

    Science.gov (United States)

    Doleželová, M.; Svora, P.; Vimmrová, A.

    2017-10-01

    In spite of the fact that gypsum is one of the most environmentally friendly binders, utilization of gypsum products is relatively narrow. The main problem of gypsum materials is their low resistance to the wet environment and radical decrease of mechanical properties with increasing moisture. The solution of the problem could be in use of composed gypsum-based binders, usually ternary, comprising gypsum, pozzolan and alkali activator of pozzolan reaction. These materials have a better moisture resistance and often also better mechanical properties. Paper provides literature survey of the possible compositions, properties and ways of utilization of the composed gypsum-based binders with latent hydraulic and pozzolan materials together with some results of present research performed by authors.

  13. Dental fiber-post resin base material: a review

    Science.gov (United States)

    Xu, Chun; Zhang, Fu-qiang

    2014-01-01

    Teeth that have short clinical crown, which are not alone enough to support the definitive restoration can be best treated using the post and core system. The advantages of fiber post over conventional metallic post materials have led to its wide acceptance. In addition to that the combination of aesthetic and mechanical benefits of fiber post has provided it with a rise in the field of dentistry. Also the results obtained from some clinical trials have encouraged the clinicians to use the fiber posts confidently. Fiber posts are manufactured from pre-stretched fibers impregnated within a resin matrix. The fibers could that be of carbon, glass/silica, and quartz, whereas Epoxy and bis-GMA are the most widely used resin bases. But recently studies are also found to be going on for polyimide as possible material for the fiber post resin base as a substitute for the conventional materials. PMID:24605208

  14. [Evidence-based management of medical disposable materials].

    Science.gov (United States)

    Yang, Hai

    2009-03-01

    Evidence-based management of medical disposable materials pays attention to collect evidence comprehensively and systematically, accumulate and create evidence through its own work and also evaluate evidence strictly. This can be used as a function to guide out job. Medical disposable materials evidence system contains product register qualification, product quality certification, supplier's behavior, internal and external communication evidence. Managers can find different ways in creating and using evidence referring to specific inside and outside condition. Evidence-based management can help accelerating the development of management of medical disposable materials from traditional experience pattern to a systematic and scientific pattern. It also has the very important meaning to improve medical quality, control the unreasonable growth of medical expense and make purchase and supply chain be more efficient.

  15. Dental fiber-post resin base material: a review.

    Science.gov (United States)

    Lamichhane, Aashwini; Xu, Chun; Zhang, Fu-Qiang

    2014-02-01

    Teeth that have short clinical crown, which are not alone enough to support the definitive restoration can be best treated using the post and core system. The advantages of fiber post over conventional metallic post materials have led to its wide acceptance. In addition to that the combination of aesthetic and mechanical benefits of fiber post has provided it with a rise in the field of dentistry. Also the results obtained from some clinical trials have encouraged the clinicians to use the fiber posts confidently. Fiber posts are manufactured from pre-stretched fibers impregnated within a resin matrix. The fibers could that be of carbon, glass/silica, and quartz, whereas Epoxy and bis-GMA are the most widely used resin bases. But recently studies are also found to be going on for polyimide as possible material for the fiber post resin base as a substitute for the conventional materials.

  16. Graphene-based and graphene-like materials

    Science.gov (United States)

    Ivanovskii, Alexander L.

    2012-07-01

    The review generalizes information on methods for modification of graphene-based carbon materials through creation of structural defects, introduction of substitutional impurities, adsorption of impurity atoms and mechanical deformations. Graphene ribbons and nano-flakes, graphene allotropes, as well as multi-layer graphenes and graphene-containing hybrid carbon structures are considered. Methods of synthesis and the results of studies on the properties and simulation of graphene derivatives (graphane, graphone and fluorographene) are discussed. The results obtained in studies of related non-carbon graphene-like materials including silicon-, germanium- and tin-based structural analogues of graphene, graphene-like binary phases SiC, GeC, SiGe, SiSn, etc., as well as compounds AIIIBV (white graphene, etc.) and AIIBVI (BeO, ZnO, ZnS) are generalized. Other graphene-like materials including metal dichalcogenides, oxides and carbides are briefly outlined. The bibliography includes 605 references.

  17. The performance of one belt and one road exchange rate: Based on improved singular spectrum analysis

    Science.gov (United States)

    Lai, Lin; Guo, Kun

    2017-10-01

    ;One Belt and One Road; strategy in China is on push of foreign trade openness at northwest, southwest and northeast, absorption of the excess capacity and new support for economic increase. However, the fluctuation in RMB exchange rate with the countries along the road is unstable so related Chinese enterprises will face high risk of exchange rate. Precise explanation or prediction for exchange rate has been the challengeable hop point in the international finance. This paper decomposed the One Belt One Road Exchange Rate Index (OBORR) and the RMB Effective Exchange Rate Index (CNYX) into trend term, market fluctuation term and noise term using improved singular spectrum analysis (SSA). It turns out that the increasing velocity of OBORR is greater than that of CNYX in the long term, and there is dynamic lead-lag structure in the medium term. In the short term, the fluctuation range and frequency of OBORR are greater than those of CNYX, which means there will be more exchange rate risks in One Belt and One Road countries.

  18. Energy enhancer for mask based laser materials processing

    DEFF Research Database (Denmark)

    Bastue, Jens; Olsen, Flemmming Ove

    1996-01-01

    A device capable of drastically improving the energy efficiency of present mask based laser materials processing systems is presented. Good accordance between experiments and simulations for a TEA-CO2 laser system designed for laser marking has been demonstrated. The energy efficiency may...

  19. Phosphorus-based compounds for EUV multilayer optics materials

    NARCIS (Netherlands)

    Medvedev, Viacheslav; Yakshin, Andrey; van de Kruijs, Robbert Wilhelmus Elisabeth; Bijkerk, Frederik

    2015-01-01

    We have evaluated the prospects of phosphorus-based compounds in extreme ultraviolet multilayer optics. Boron phosphide (BP) is suggested to be used as a spacer material in reflective multilayer optics operating just above the L-photoabsorption edge of P (λ ≈9.2 nm). Mo, Ag, Ru, Rh, and Pd were

  20. Developing Corpus-Based Materials to Teach Pragmatic Routines

    Science.gov (United States)

    Bardovi-Harlig, Kathleen; Mossman, Sabrina; Vellenga, Heidi E.

    2015-01-01

    This article describes how to develop teaching materials for pragmatics based on authentic language by using a spoken corpus. The authors show how to use the corpus in conjunction with textbooks to identify pragmatic routines for speech acts and how to extract appropriate language samples and adapt them for classroom use. They demonstrate how to…

  1. and O-based composite materials derived from differential ...

    Indian Academy of Sciences (India)

    Abstract. In this work, we have made an effort to determine whether the effective atomic numbers of H-, C-, N- and O-based composite materials would indeed remain a constant over the energy grid of 280–1200 keV wherein incoherent scattering dominates their interaction with photons. For this purpose, the differential ...

  2. Finding Environmental Knowledge in SCUBA-Based Textual Materials

    Science.gov (United States)

    Gündogdu, Cemal; Aygün, Yalin; Ilkim, Mehmet

    2018-01-01

    As marine environments within the adventure domain are future key-settings for recreational SCUBA diving experience, SCUBA-based textual materials should provide insight into environmental knowledge that is well connected to the novice divers' behaviour and attitude. This research is concerned with a major recreational SCUBA diver manual for…

  3. Innovations in bonding to zirconia-based materials: Part I

    NARCIS (Netherlands)

    Abou Shelib, M.N.M.; Matinlinna, J.P.; Salameh, Z.; Ounsi, H.

    2008-01-01

    Abstract Objectives Establishing a reliable bond to zirconia-based materials has proven to be difficult which is the major limitation against fabricating adhesive zirconia restorations. This bond could be improved using novel selective infiltration etching conditioning in combination with engineered

  4. Engineering the electronic structure of lanthanide based materials

    NARCIS (Netherlands)

    Rogers, E.G.

    2012-01-01

    Lanthanide based materials are used in everything from phosphors for light bulbs and LEDs, to scintillators for medical imaging purposes to magnets. They also show potential for spintronics and for increasing the efficiency of solar cells. Knowing the energy of the lanthanide 4f and 5d states is

  5. Lithium-based inorganic-organic framework materials

    OpenAIRE

    Yeung, Hamish Hei-Man

    2013-01-01

    This dissertation describes research into lithium-based inorganic-organic frameworks, which has led to an increased understanding of the structural diversity and properties of these materials. The crystal structures of 11 new forms of lithium tartrate, based on chiral, racemic and meso forms of the ligand, have been discovered, including eight anhydrous isomers of dilithium tartrate, Li2(C4H4O6). An experimental and computational study of their formation behaviour and energetics has shown tha...

  6. Health care provider perceptions of a query-based health information exchange: barriers and benefits

    Directory of Open Access Journals (Sweden)

    Gary L. Cochran

    2015-06-01

    Full Text Available BackgroundHealth information exchange (HIE systems are implemented nationwide to integrate health information and facilitate communication among providers. The Nebraska Health Information Initiative is a state-wide HIE launched in 2009. Objective The purpose of this study was to conduct a comprehensive assessment of health care providers’ perspectives on a query-based HIE, including barriers to adoption and important functionality for continued utilization. MethodsWe surveyed 5618 Nebraska health care providers in 2013. Reminder letters were sent 30 days after the initial mailing. ResultsA total of 615 questionnaires (11% were completed. Of the 100 current users, 63 (63% indicated satisfaction with HIE. The most common reasons for adoption among current or previous users of an HIE (N = 198 were improvement in patient care (N = 111, 56% as well as receiving (N = 95, 48% and sending information (N = 80, 40% in the referral network. Cost (N = 233, 38% and loss of productivity (N = 220, 36% were indicated as the ‘major barriers’ to adoption by all respondents. Accessing a comprehensive patient medication list was identified as the most important feature of the HIE (N = 422, 69%. ConclusionsThe cost of HIE access and workflow integration are significant concerns of health care providers. Additional resources to assist practices plan the integration of the HIE into a sustainable workflow may be required before widespread adoption occurs. The clinical information sought by providers must also be readily available for continued utilization. Query-based HIEs must ensure that medication history, laboratory results and other desired clinical information be present, or long-term utilization of the HIE is unlikely. 

  7. A cloud based tool for knowledge exchange on local scale flood risk.

    Science.gov (United States)

    Wilkinson, M E; Mackay, E; Quinn, P F; Stutter, M; Beven, K J; MacLeod, C J A; Macklin, M G; Elkhatib, Y; Percy, B; Vitolo, C; Haygarth, P M

    2015-09-15

    There is an emerging and urgent need for new approaches for the management of environmental challenges such as flood hazard in the broad context of sustainability. This requires a new way of working which bridges disciplines and organisations, and that breaks down science-culture boundaries. With this, there is growing recognition that the appropriate involvement of local communities in catchment management decisions can result in multiple benefits. However, new tools are required to connect organisations and communities. The growth of cloud based technologies offers a novel way to facilitate this process of exchange of information in environmental science and management; however, stakeholders need to be engaged with as part of the development process from the beginning rather than being presented with a final product at the end. Here we present the development of a pilot Local Environmental Virtual Observatory Flooding Tool. The aim was to develop a cloud based learning platform for stakeholders, bringing together fragmented data, models and visualisation tools that will enable these stakeholders to make scientifically informed environmental management decisions at the local scale. It has been developed by engaging with different stakeholder groups in three catchment case studies in the UK and a panel of national experts in relevant topic areas. However, these case study catchments are typical of many northern latitude catchments. The tool was designed to communicate flood risk in locally impacted communities whilst engaging with landowners/farmers about the risk of runoff from the farmed landscape. It has been developed iteratively to reflect the needs, interests and capabilities of a wide range of stakeholders. The pilot tool combines cloud based services, local catchment datasets, a hydrological model and bespoke visualisation tools to explore real time hydrometric data and the impact of flood risk caused by future land use changes. The novel aspects of the

  8. Acid-base balance disturbances in plasma exchange depend on the replacement fluid used.

    Science.gov (United States)

    Cid, Joan; Carbassé, Gloria; Gamir, Montse; Jiménez, María; Arellano-Rodrigo, Eduardo; Lozano, Miguel

    2015-11-01

    Metabolic alkalosis occurs as a direct result of plasma exchange (PE) because of metabolism of citrate. However, we observed a decrease of serum pH and bicarbonate after PE when albumin was used as replacement fluid. The acid-base balance in 2730 PEs using different replacement fluids (albumin, fresh-frozen plasma [FFP], or both) was measured, and absolute changes (Δ) in acid-base balance were compared. The frequency of adverse effects (AEs) before and after using prophylactic administration of sodium bicarbonate was compared. A decrease of serum pH and bicarbonate was observed after PEs when albumin was used as replacement fluid (Δ pH = -0.06 ± 0.04; Δ bicarbonate = -4.03 ± 2.29 mmol/L; Δ base excess = -2.54 ± 3.82 mmol/L). An increase of serum pH and bicarbonate was observed after PEs when FFP was used as replacement fluid (Δ pH = +0.04 ± 0.05; Δ bicarbonate = +3.6 ± 3.68 mmol/L; Δ base excess = +1.62 ± 4.51 mmol/L). The prophylactic administration of sodium bicarbonate corrected partially the decrease of serum pH and bicarbonate after finishing PEs when albumin was used as replacement fluid (Δ pH = -0.04 ± 0.04; Δ bicarbonate = -3.1 ± 2.47 mmol/L; Δ base excess = -3.35 ± 3.06 mmol/L). The frequency of AEs after using prophylactic administration of sodium bicarbonate was lower in comparison with the frequency of AEs before using prophylactic administration of sodium bicarbonate (2.0% vs. 4.8%; p < 0.001). A decrease of serum pH and bicarbonate appeared in patients after PEs when albumin was used as replacement fluid; it was corrected partially with prophylactic administration of sodium bicarbonate, and it was associated with fewer AEs. © 2015 AABB.

  9. Graphene-based materials for supercapacitor electrodes – A review

    Directory of Open Access Journals (Sweden)

    Qingqing Ke

    2016-03-01

    Full Text Available The graphene-based materials are promising for applications in supercapacitors and other energy storage devices due to the intriguing properties, i.e., highly tunable surface area, outstanding electrical conductivity, good chemical stability and excellent mechanical behavior. This review summarizes recent development on graphene-based materials for supercapacitor electrodes, based on their macrostructural complexity, i.e., zero-dimensional (0D (e.g. free-standing graphene dots and particles, one-dimensional (1D (e.g. fiber-type and yarn-type structures, two-dimensional (2D (e.g. graphenes and graphene-based nanocomposite films, and three-dimensional (3D (e.g. graphene foam and hydrogel-based nanocomposites. There are extensive and on-going researches on the rationalization of their structures at varying scales and dimensions, development of effective and low cost synthesis techniques, design and architecturing of graphene-based materials, as well as clarification of their electrochemical performance. It is indicated that future studies should focus on the overall device performance in energy storage devices and large-scale process in low costs for the promising applications in portable and wearable electronic, transport, electrical and hybrid vehicles.

  10. Heat transfer performance of water and Nanoencapsulated n-nonadecane based Nanofluids in a double pipe heat exchanger

    Science.gov (United States)

    Doruk, Semahat; Şara, Osman Nuri; Karaipekli, Ali; Yapıcı, Sinan

    2017-06-01

    The heat transfer and pressure drop characteristics for the flow of water, which is base fluid, and nanoencapsulated n-nonadecane based nanofluids in a double pipe heat exchanger were investigated. The results showed that no improvement in overall heat transfer coefficient was observed for the nanofluids containing 0.42% and 0.84% solid volume ratios with reference to the base fluid, while an improvement of about 10% was obtained for the nanofluids containing 1.68% solid volume ratio. It was found that the friction factors for the nanofluids exhibited a slight increase reference to the base fluid. A performance analysis based on constant pumping power was also performed.

  11. Graphene-Based Materials for Lithium-Ion Hybrid Supercapacitors.

    Science.gov (United States)

    Ma, Yanfeng; Chang, Huicong; Zhang, Miao; Chen, Yongsheng

    2015-09-23

    Lithium-ion hybrid supercapacitors (LIHSs), also called Li-ion capacitors, have attracted much attention due to the combination of the rapid charge-discharge and long cycle life of supercapacitors and the high energy-storage capacity of lithium-ion batteries. Thus, LIHSs are expected to become the ultimate power source for hybrid and all-electric vehicles in the near future. As an electrode material, graphene has many advantages, including high surface area and porous structure, high electric conductivity, and high chemical and thermal stability, etc. Compared with other electrode materials, such as activated carbon, graphite, and metal oxides, graphene-based materials with 3D open frameworks show higher effective specific surface area, better control of channels, and higher conductivity, which make them better candidates for LIHS applications. Here, the latest advances in electrode materials for LIHSs are briefly summarized, with an emphasis on graphene-based electrode materials (including 3D graphene networks) for LIHS applications. An outlook is also presented to highlight some future directions. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Corrosion of structural materials by lead-based reactor coolants.

    Energy Technology Data Exchange (ETDEWEB)

    Abraham, D. P.; Leibowitz, L.; Maroni, V. A.; McDeavitt, S. M.; Raraz, A. G.

    2000-11-16

    Advanced nuclear reactor design has, in recent years, focused increasingly on the use of heavy-liquid-metal coolants, such as lead and lead-bismuth eutectic. Similarly, programs on accelerator-based transmutation systems have also considered the use of such coolants. Russian experience with heavy-metal coolants for nuclear reactors has lent credence to the validity of this approach. Of significant concern is the compatibility of structural materials with these coolants. We have used a thermal convection-based test method to allow exposure of candidate materials to molten lead and lead-bismuth flowing under a temperature gradient. The gradient was deemed essential in evaluating the behavior of the test materials in that should preferential dissolution of components of the test material occur we would expect dissolution in the hotter regions and deposition in the colder regions, thus promoting material transport. Results from the interactions of a Si-rich mild steel alloy, AISI S5, and a ferritic-martensitic stainless steel, HT-9, with the molten lead-bismuth are presented.

  13. Material Discrimination Based on K-edge Characteristics

    Directory of Open Access Journals (Sweden)

    Peng He

    2013-01-01

    Full Text Available Spectral/multienergy CT employing the state-of-the-art energy-discriminative photon-counting detector can identify absorption features in the multiple ranges of photon energies and has the potential to distinguish different materials based on K-edge characteristics. K-edge characteristics involve the sudden attenuation increase in the attenuation profile of a relatively high atomic number material. Hence, spectral CT can utilize material K-edge characteristics (sudden attenuation increase to capture images in available energy bins (levels/windows to distinguish different material components. In this paper, we propose an imaging model based on K-edge characteristics for maximum material discrimination with spectral CT. The wider the energy bin width is, the lower the noise level is, but the poorer the reconstructed image contrast is. Here, we introduce the contrast-to-noise ratio (CNR criterion to optimize the energy bin width after the K-edge jump for the maximum CNR. In the simulation, we analyze the reconstructed image quality in different energy bins and demonstrate that our proposed optimization approach can maximize CNR between target region and background region in reconstructed image.

  14. Transient analysis of subcritical/supercritical carbon dioxide based natural circulation loop with end heat exchangers: experimental study

    Science.gov (United States)

    Yadav, Ajay Kumar; Ramgopal, Maddali; Bhattacharyya, Souvik

    2017-09-01

    Carbon dioxide (CO2) based natural circulation loops (NCLs) has gained attention due to its compactness with higher heat transfer rate. In the present study, experimental investigations have been carried out to capture the transient behaviour of a CO2 based NCL operating under subcritical as well as supercritical conditions. Water is used as the external fluid in cold and hot heat exchangers. Results are obtained for various inlet temperatures (323-353 K) of water in the hot heat exchanger and a fixed inlet temperature (305 K) of cooling water in the cold heat exchanger. Effect of loop operating pressure (50-90 bar) on system performance is also investigated. Effect of loop tilt in two different planes (XY and YZ) is also studied in terms of transient as well as steady state behaviour of the loop. Results show that the time required to attain steady state decreases as operating pressure of the loop increases. It is also observed that the change in temperature of loop fluid (CO2) across hot or cold heat exchanger decreases as operating pressure increases.

  15. Modification of polyamide-CdS-CdSe composite material films with Ag using a cation–cation exchange reaction

    Energy Technology Data Exchange (ETDEWEB)

    Krylova, V.; Žalenkienė, S.; Dukstienė, N. [Department of Physical and Inorganic Chemistry, Kaunas University of Technology, Radvilenu st. 19, LT-50254, Kaunas (Lithuania); Baltrusaitis, J., E-mail: job314@lehigh.edu [Department of Chemical and Biomolecular Engineering, Lehigh University, B336 Iacocca Hall, 111 Research Drive, Bethlehem, PA 18015 (United States)

    2015-10-01

    Highlights: • We investigated deposition of a mixed CdSe-CdS-Ag{sub 2}Se-Ag{sub 2}S on polyamide. • A single chalcogen precursor – K{sub 2}SeS{sub 2}O{sub 6} – was used. • AAS showed five- to ten-fold excess of chalcogens diffused into PA. • Addition of AgNO{sub 3} resulted in subsurface Ag{sub 2}Se–Ag{sub 2}S formation. - Abstract: Thin mixed CdSe-CdS-Ag{sub 2}Se-Ag{sub 2}S films were deposited on a polyamide 6 (PA) surface by successfully using a cation-exchange reaction between Cd{sup 2+} and Ag{sup +} to convert CdSe-CdS into Ag{sub 2}Se-Ag{sub 2}S. These were deposited using a K{sub 2}SeS{sub 2}O{sub 6} precursor solution at 60 °C followed by cadmium acetate (Cd(CH{sub 3}COO){sub 2}). An aqueous AgNO{sub 3} solution was used as the Ag source. XRD patterns showed a complex PA-Cd-S-Se-Ag film crystalline composition with CdS, CdSe, Ag{sub 2}S and Ag{sub 2}Se peaks. Calculated dislocation density ranged within 5–15 × 10{sup 13} lines·m{sup −2} indicating high quality atomic layers. Atomic Absorption Spectroscopy (AAS) showed five- to ten-fold excess of chalcogens to metals in the thin films formed. No chalcogenides were observed on the sample surface during XPS analysis after Ag exchange due to the desorption of CdS and CdSe layers, not diffused into the bulk of the polymer suggesting that silver chalcogenides were located subsurface, as opposed to the outermost layer, likely comprised of Ag{sub 2}O.

  16. Knitted radar absorbing materials (RAM) based on nickel–cobalt magnetic materials

    Energy Technology Data Exchange (ETDEWEB)

    Teber, Ahmet, E-mail: aht10003@engr.uconn.edu [Department of Electrical and Computer Engineering, University of Connecticut, Storrs, CT 06269 (United States); Unver, Ibrahim, E-mail: iunver@gtu.edu.tr [Department of Physics, Gebze Technical University, Kocaeli 41400 (Turkey); Kavas, Huseyin, E-mail: huseyin.kavas@medeniyet.edu.tr [Department of Physics, Istanbul Medeniyet University, Istanbul 34000 (Turkey); Aktas, Bekir, E-mail: aktas@gtu.edu.tr [Department of Physics, Gebze Technical University, Kocaeli 41400 (Turkey); Bansal, Rajeev, E-mail: rajeev@engr.uconn.edu [Department of Electrical and Computer Engineering, University of Connecticut, Storrs, CT 06269 (United States)

    2016-05-15

    There has been a long-standing interest in the development of flexible, lightweight, thin, and reconfigurable radar absorbing materials (RAM) for military applications such as camouflaging ground-based hardware against airborne radar observation. The use of polymeric Polyacrylonitrile (PAN) fabrics as a host matrix for magnetic metal nano-particles (either at the yarn-stage or after weaving the fabric) for shielding and absorbing applications has been described in the literature. In our experimental investigation, the relative concentrations of Nickel and Cobalt as well as the coating time are varied with a view to optimizing the microwave absorption characteristics of the resulting PAN-based composite material in the radar-frequency bands (X, K{sub u}, and K). It is found that the PAN samples with the shortest coating time have the best return losses (under −20 dB return loss over a moderate bandwidth). - Graphical abstract: Here, we added the graphical abstract that provides summary the contents of the article in a concise pictorial form. - Highlights: • Flexible lightweight, thin, reconfigurable radar absorbing materials are proposed. • Polyacrylonitrile (PAN) fabrics are coated with nickel, cobalt magnetic materials. • The coating times affects microwave constitutive parameters and absorption. • Microwave absorption measurements were done via transmission line technique. • Microwave absorption is due to dielectric losses rather than magnetic losses.

  17. Integrating UNESCO ICT-Based Instructional Materials in Chemistry Lessons

    Directory of Open Access Journals (Sweden)

    CHARLIE P. NACARIO

    2014-08-01

    Full Text Available This study determined the effectiveness of the lessons in Chemistry integrating UNESCO ICT-based instructional material on the achievement of Chemistry students at Central Bicol State University of Agriculture. It aimed to identify lessons that may be developed integrating UNESCO ICT-based instructional materials, determine the effect of the developed lessons using the material on: conceptual understanding; science process skills; and attitude towards chemistry and gather insights from the experiences of the students and teacher. The study used the single group pretest and posttest experimental design. Descriptive, quantitative and qualitative techniques were also utilized. Quantitative data were taken from the pretest-posttest results on the Test on Conceptual Understanding, Science Process Skills and Chemistry Attitudinaire. Qualitative data were drawn from the experts’ assessment of the developed lessons and research instruments, and the insights of students and teacher. The developed lessons integrating UNESCO ICT-based instructional materials were Atomic Model and Structure, Periodic Table of Elements, Chemical Bonding, and Balancing Chemical Equation. These lessons increased the conceptual understanding of the students by topic and skill from very low mastery to average mastery level. The students have slightly improved along the different science process skills. After teaching the lessons, the students’ attitude also improved. The students became more motivated and interested in Chemistry and the lessons were student centered and entailed teacher’s competence and flexibility in computer use.

  18. Material procedure quality forecast based on genetic BP neural network

    Science.gov (United States)

    Zheng, Bao-Hua

    2017-07-01

    Material procedure quality forecast plays an important role in quality control. This paper proposes a prediction model based on genetic algorithm (GA) and back propagation (BP) neural network. It can obtain the initial weights and thresholds of optimized BP neural network with the GA global search ability. A material process quality prediction model with the optimized BP neural network is adopted to predict the error of future process to measure the accuracy of process quality. The results show that the proposed method has the advantages of high accuracy and fast convergence rate compared with BP neural network.

  19. EFRC: Polymer-Based Materials for Harvesting Solar Energy (stimulus)"

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Thomas P. [Univ. of Massachusetts, Amherst, MA (United States)

    2016-12-08

    The University of Massachusetts Amherst is proposing an Energy Frontier Research Center (EFRC) on Polymer-Based Materials for Harvesting Solar Energy that will integrate the widely complementary experimental and theoretical expertise of 23 faculty at UMass-Amherst Departments with researchers from the University of Massachusetts Lowell, University of Pittsburgh, the Pennsylvania State University and Konarka Technologies, Inc. Collaborative efforts with researchers at the Oak Ridge National Laboratory, the University of Bayreuth, Seoul National University and Tohoku University will complement and expand the experimental efforts in the EFRC. Our primary research aim of this EFRC is the development of hybrid polymer-based devices with efficiencies more than twice the current organic-based devices, by combining expertise in the design and synthesis of photoactive polymers, the control and guidance of polymer-based assemblies, leadership in nanostructured polymeric materials, and the theory and modeling of non-equilibrium structures. A primary goal of this EFRC is to improve the collection and conversion efficiency of a broader spectral range of solar energy using the directed self-assembly of polymer-based materials so as to optimize the design and fabrication of inexpensive devices.

  20. Knitted radar absorbing materials (RAM) based on nickel-cobalt magnetic materials

    Science.gov (United States)

    Teber, Ahmet; Unver, Ibrahim; Kavas, Huseyin; Aktas, Bekir; Bansal, Rajeev

    2016-05-01

    There has been a long-standing interest in the development of flexible, lightweight, thin, and reconfigurable radar absorbing materials (RAM) for military applications such as camouflaging ground-based hardware against airborne radar observation. The use of polymeric Polyacrylonitrile (PAN) fabrics as a host matrix for magnetic metal nano-particles (either at the yarn-stage or after weaving the fabric) for shielding and absorbing applications has been described in the literature. In our experimental investigation, the relative concentrations of Nickel and Cobalt as well as the coating time are varied with a view to optimizing the microwave absorption characteristics of the resulting PAN-based composite material in the radar-frequency bands (X, Ku, and K). It is found that the PAN samples with the shortest coating time have the best return losses (under -20 dB return loss over a moderate bandwidth).

  1. Graphene-based Materials for Biosensing and Bioimaging

    Energy Technology Data Exchange (ETDEWEB)

    Du, Dan; Yang, Yuqi; Lin, Yuehe

    2012-12-01

    Graphene, a free-standing two-dimensional crystal with one-atom thickness, exhibits distinct properties that are highly attractive for biosensing and bioimaging, such as a high electrical conductivity, a large planar area, and an excellent ability to quench fluorescence. This article selectively reviews recent advances in the field of graphene-based materials for biosensing and bioimaging. In particular, graphene-based enzyme biosensors, DNA biosensors, and immunosensors are summarized in detail. Graphene-based biotechnology for cell imaging is also described. Future perspectives and possible challenges in this rapidly developing area are also discussed.

  2. Using bio-based polymers for curing cement-based materials

    NARCIS (Netherlands)

    Zlopasa, J.; Koenders, E.A.B.; Picken, S.J.

    2014-01-01

    Curing is the process of controlling the rate and extent of moisture loss from the surface of cement based materials. It is the final stage in the production of cement-based materials and it is the essential part for achieving continuous hydration of cement, while avoiding cracking due to drying

  3. Comparison of heat flux estimations from two turbulent exchange models based on thermal UAV data.

    Science.gov (United States)

    Hoffmann, Helene; Nieto, Hector; Jensen, Rasmus; Friborg, Thomas

    2015-04-01

    Advantages of UAV (Unmanned Aerial Vehicle) data-collection, compared to more traditional data-collections are numerous and already well-discussed (Berni et al., 2009; Laliberte et al., 2011; Turner et al., 2012). However studies investigating the quality and applications of UAV-data are crucial if advantages are to be beneficial for scientific purposes. In this study, thermal data collected over an agricultural site in Denmark have been obtained using a fixed-wing UAV and investigated for the estimation of heat fluxes. Estimation of heat fluxes requires high precision data and careful data processing. Latent, sensible and soil heat fluxes are estimates through two models of the two source energy modelling scheme driven by remotely sensed observations of land surface temperature; the original TSEB (Norman et al., 1995) and the DTD (Norman et al., 2000) which builds on the TSEB. The DTD model accounts for errors arising when deriving radiometric temperatures and can to some extent compensate for the fact that thermal cameras rarely are accurate. The DTD model requires an additional set of remotely sensed data during morning hours of the day at which heat fluxes are to be determined. This makes the DTD model ideal to use when combined with UAV data, because acquisition of data is not limited by fixed time by-passing tracks like satellite images (Guzinski et al., 2013). Based on these data, heat fluxes are computed from the two models and compared with fluxes from an eddy covariance station situated within the same designated agricultural site. This over-all procedure potentially enables an assessment of both the collected thermal UAV-data and of the two turbulent exchange models. Results reveal that both TSEB and DTD models compute heat fluxes from thermal UAV data that is within a very reasonable range and also that estimates from the DTD model is in best agreement with the eddy covariance system.

  4. A weak-base fibrous anion exchanger effective for rapid phosphate removal from water.

    Science.gov (United States)

    Awual, Md Rabiul; Jyo, Akinori; El-Safty, Sherif A; Tamada, Masao; Seko, Noriaki

    2011-04-15

    This work investigated that weak-base anion exchange fibers named FVA-c and FVA-f were selectively and rapidly taken up phosphate from water. The chemical structure of both FVA-c and FVA-f was the same; i.e., poly(vinylamine) chains grafted onto polyethylene coated polypropylene fibers. Batch study using FVA-c clarified that this preferred phosphate to chloride, nitrate and sulfate in neutral pH region and an equilibrium capacity of FVA-c for phosphate was from 2.45 to 6.87 mmol/g. Column study using FVA-f made it clear that breakthrough capacities of FVA-f were not strongly affected by flow rates from 150 to 2000 h(-1) as well as phosphate feed concentration from 0.072 to 1.6mM. Under these conditions, breakthrough capacities were from 0.84 to 1.43 mmol/g indicating high kinetic performances. Trace concentration of phosphate was also removed from feeds containing 0.021 and 0.035 mM of phosphate at high feed flow rate of 2500 h(-1), breakthrough capacities were 0.676 and 0.741 mmol/g, respectively. The column study also clarified that chloride and sulfate did not strongly interfere with phosphate uptake even in their presence of equimolar and fivefold molar levels. Adsorbed phosphate on FVA-f was quantitatively eluted with 1M HCl acid and regenerated into hydrochloride form simultaneously for next phosphate adsorption operation. Therefore, FVA-f is able to use long time even under rigorous chemical treatment of multiple regeneration/reuse cycles without any noticeable deterioration. Copyright © 2011 Elsevier B.V. All rights reserved.

  5. Evaluation and comparison of SuperLig{reg_sign} 644, resorcinol-formaldehyde and CS-100 ion exchange materials for the removal of cesium from simulated alkaline supernate

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G.N.; Bray, L.A.; Eloviche, R.J. [Pacific Northwest Lab., Richland, WA (United States); Bruening, R.L.; Decker, R.M. [IBC Advanced Technologies, Inc., Provo, UT (United States); Kafka, T.M.; White, L.R. [3M Co., St. Paul, MN (United States)

    1995-03-01

    PNL evaluated three polymeric materials for Cs removal efficiency from a simulated Hanford Neutralized Current Acid Waste (NCAW) supernatant liquid using 200 mL ion exchange columns. Cs loadings (mmole Cs/g resin) were 0.20, 0.18, and 0.039 for Super Lig 644, R-F, and CS-100 (0.045, 0.070, 0.011 mmole Cs/mL resin). Elution of each resin material with 0.5 M HNO{sub 3} required 3.5, 7.0, and 3.2 cv to reach 0.1 C/C{sub 0} for the respective materials, resulting in volume compressions of 27, 20, and 6.9. Peak Cs concentrations during elution was 185, 38.5, and 27.8 C/C{sub 0}. SuperLig 644 had the highest Cs loading per gram in NCAW and the greatest volume compression on aci elution. Because of high density and poor elution, R-F had the highest Cs loading per unit volume and lower volume compression. CS-100, the baseline material for Cs removal at Hanford, was inferior to both SuperLig 644 and R-F in terms of Cs loading and selectivity over sodium.

  6. High Temperature Thermoelectric Properties of ZnO Based Materials

    DEFF Research Database (Denmark)

    Han, Li

    This thesis investigated the high temperature thermoelectric properties of ZnO based materials. The investigation first focused on the doping mechanisms of Al-doped ZnO, and then the influence of spark plasma sintering conditions on the thermoelectric properties of Al, Ga-dually doped ZnO....... Following that, the nanostructuring effect for Al-doped ZnO was systematically investigated using samples with different microstructure morphologies. At last, the newly developed ZnCdO materials with superior thermoelectric properties and thermal stability were introduced as promising substitutions...... for conventional ZnO materials. For Al-doped ZnO, α- and γ-Al2O3 were selectively used as dopants in order to understand the doping mechanism of each phase and their effects on the thermoelectric properties. The samples were prepared by the spark plasma sintering technique from precursors calcined at various...

  7. Acrylamide-based magnetic nanosponges: a new smart nanocomposite material.

    Science.gov (United States)

    Bonini, Massimo; Lenz, Sebastian; Falletta, Ester; Ridi, Francesca; Carretti, Emiliano; Fratini, Emiliano; Wiedenmann, Albrecht; Baglioni, Piero

    2008-11-04

    Nanocomposite materials consisting of CoFe2O4 magnetic nanoparticles and a polyethylene glycol-acrylamide gel matrix have been synthesized. The structure of such materials was studied by means of small-angle scattering of X-rays and polarized neutrons, showing that the CoFe2O4 nanoparticles were successfully and homogeneously embedded in the gel structure. Magnetic, viscoelastic, and water retention properties of the nanocomposite gel confirm that the properties of both nanoparticles and gel are combined in the resulting nanomagnetic gel. Scanning electron microscopy highlights the nanocomposite nature of the material, showing the presence of a gel structure with different pore size distributions (pores with micron and nano-size distributions) that can be used as active sponge-like nanomagnetic container for water-based formulations as oil-in-water microemulsions.

  8. Cement-Based Materials for Nuclear Waste Storage

    CERN Document Server

    Cau-di-Coumes, Céline; Frizon, Fabien; Lorente, Sylvie

    2013-01-01

    As the re-emergence of nuclear power as an acceptable energy source on an international basis continues, the need for safe and reliable ways to dispose of radioactive waste becomes ever more critical. The ultimate goal for designing a predisposal waste-management system depends on producing waste containers suitable for storage, transportation and permanent disposal. Cement-Based Materials for Nuclear-Waste Storage provides a roadmap for the use of cementation as an applied technique for the treatment of low- and intermediate-level radioactive wastes.Coverage includes, but is not limited to, a comparison of cementation with other solidification techniques, advantages of calcium-silicate cements over other materials and a discussion of the long-term suitability and safety of waste packages as well as cement barriers. This book also: Discusses the formulation and production of cement waste forms for storing radioactive material Assesses the potential of emerging binders to improve the conditioning of problemati...

  9. Designing Listening Material Based on Visual Multimodality Compositions

    Directory of Open Access Journals (Sweden)

    Jepri Ali Saiful

    2015-06-01

    Full Text Available In recent decades, multimodality has eventually augmented into the realm of language teaching and learning known as Applied Multimodality. This interdisciplinary approach draws on a multiplicity of communication or representation modes, all of which contribute to meaning. Accordingly, images, colors, and sounds within a text are catalysts to increase an audience’s reception of an idea or concept of the text, that is, a message. Thus, the present article intends to make a contribution to the field of material development in English language teaching. The aim of this article is therefore to provide guidelines for ELT teachers on how to design listening materials based on visual multimodal compositions of image and text. The result is that the compositions of image and text in designing listening materials rests upon three main principles: information value, salience and framing. These principles enable students’ L2 acquisition through listening as proved by recent research.

  10. Optical Fibre Sensors Using Graphene-Based Materials: A Review.

    Science.gov (United States)

    Hernaez, Miguel; Zamarreño, Carlos R; Melendi-Espina, Sonia; Bird, Liam R; Mayes, Andrew G; Arregui, Francisco J

    2017-01-14

    Graphene and its derivatives have become the most explored materials since Novoselov and Geim (Nobel Prize winners for Physics in 2010) achieved its isolation in 2004. The exceptional properties of graphene have attracted the attention of the scientific community from different research fields, generating high impact not only in scientific journals, but also in general-interest newspapers. Optical fibre sensing is one of the many fields that can benefit from the use of these new materials, combining the amazing morphological, chemical, optical and electrical features of graphene with the advantages that optical fibre offers over other sensing strategies. In this document, a review of the current state of the art for optical fibre sensors based on graphene materials is presented.

  11. Carbon-Based Materials for Photo-Triggered Theranostic Applications.

    Science.gov (United States)

    Albert, Karunya; Hsu, Hsin-Yun

    2016-11-20

    Carbon-based nanomaterials serve as a type of smart material for photo-triggered disease theranostics. The inherent physicochemical properties of these nanomaterials facilitate their use for less invasive treatments. This review summarizes the properties and applications of materials including fullerene, nanotubes, nanohorns, nanodots and nanographenes for photodynamic nanomedicine in cancer and antimicrobial therapies. Carbon nanomaterials themselves do not usually act as photodynamic therapy (PDT) agents owing to the high hydrophobicity, however, when the surface is passivated or functionalized, these materials become great vehicles for PDT. Moreover, conjugation of carbonaceous nanomaterials with the photosensitizer (PS) and relevant targeting ligands enhances properties such as selectivity, stability, and high quantum yield, making them readily available for versatile biomedical applications.

  12. Carbon-Based Materials for Photo-Triggered Theranostic Applications

    Directory of Open Access Journals (Sweden)

    Karunya Albert

    2016-11-01

    Full Text Available Carbon-based nanomaterials serve as a type of smart material for photo-triggered disease theranostics. The inherent physicochemical properties of these nanomaterials facilitate their use for less invasive treatments. This review summarizes the properties and applications of materials including fullerene, nanotubes, nanohorns, nanodots and nanographenes for photodynamic nanomedicine in cancer and antimicrobial therapies. Carbon nanomaterials themselves do not usually act as photodynamic therapy (PDT agents owing to the high hydrophobicity, however, when the surface is passivated or functionalized, these materials become great vehicles for PDT. Moreover, conjugation of carbonaceous nanomaterials with the photosensitizer (PS and relevant targeting ligands enhances properties such as selectivity, stability, and high quantum yield, making them readily available for versatile biomedical applications.

  13. A social exchange-based model of the antecedents of workplace exclusion.

    Science.gov (United States)

    Scott, Kristin L; Restubog, Simon Lloyd D; Zagenczyk, Thomas J

    2013-01-01

    We conducted 2 studies of coworker dyads to test a theoretical model exploring why and under what circumstances employees are the targets of workplace exclusion. Adopting a victim precipitation perspective, we integrate belongingness and social exchange theories to propose that employees who display workplace incivility are distrusted and therefore are targets of workplace exclusion. Highlighting the importance of the context of the perpetrator-target relationship, we also find support for the postulation that this mediated relationship is strengthened when the target employee is perceived to be a weak exchange partner and is attenuated when he or she is viewed as a valuable exchange partner. Theoretical and practical implications are discussed. PsycINFO Database Record (c) 2013 APA, all rights reserved.

  14. Technical Education Outreach in Materials Science and Technology Based on NASA's Materials Research

    Science.gov (United States)

    Jacobs, James A.

    2003-01-01

    The grant NAG-1 -2125, Technical Education Outreach in Materials Science and Technology, based on NASA s Materials Research, involves collaborative effort among the National Aeronautics and Space Administration s Langley Research Center (NASA-LaRC), Norfolk State University (NSU), national research centers, private industry, technical societies, colleges and universities. The collaboration aims to strengthen math, science and technology education by providing outreach related to materials science and technology (MST). The goal of the project is to transfer new developments from LaRC s Center for Excellence for Structures and Materials and other NASA materials research into technical education across the nation to provide educational outreach and strengthen technical education. To achieve this goal we are employing two main strategies: 1) development of the gateway website and 2) using the National Educators Workshop: Update in Engineering Materials, Science and Technology (NEW:Updates). We have also participated in a number of national projects, presented talks at technical meetings and published articles aimed at improving k-12 technical education. Through the three years of this project the NSU team developed the successful MST-Online site and continued to upgrade and update it as our limited resources permitted. Three annual NEW:Updates conducted from 2000 though 2002 overcame the challenges presented first by the September 11,2001 terrorist attacks and the slow U.S. economy and still managed to conduct very effective workshops and expand our outreach efforts. Plans began on NEW:Update 2003 to be hosted by NASA Langley as a part of the celebration of the Centennial of Controlled Flight.

  15. Factors affecting direct and indirect benefit exchange in the social media–based learning experience

    Directory of Open Access Journals (Sweden)

    Peter L. Mkhize

    2017-01-01

    Full Text Available Background: Social media platforms are thriving on the co-creation of content, usually socially orientated content about the social interests of participants. There is also a growing trend of social media application in the human resources and marketing for business purposes. This study investigates factors that have an impact on the sharing of knowledge on social media platforms, particularly students at an Open Distance Learning (ODL institution.Objective: This study evaluates the difference between direct and indirect benefit exchange expected by students when sharing knowledge.Method: Random and theoretical sampling were used to select the sample in this study from the population. A literature-informed questionnaire was used as an instrument to collect data from a selected sample of 315 students from the School of Computing at the University of South Africa.Results: A test of association was conducted to evaluate correlations, which revealed that only reputation and social language correlate with direct and indirect benefit exchange. Results indicate that there is a significant mean difference between direct and indirect benefit exchange and that issues concerning social identity and trust should be taken into account when developing social media instructional design.Conclusion: In this study, a survey was used to test the hypothesis. The authors concluded that instructional designer can design teaching and learning experience in the social media platform by catering for both direct and indirect benefit knowledge exchange. The results of the study further confirmed that some students share knowledge with the expectation of direct exchange benefit and, meanwhile, expect indirect exchange benefit.

  16. Nanostructured Mo-based electrode materials for electrochemical energy storage.

    Science.gov (United States)

    Hu, Xianluo; Zhang, Wei; Liu, Xiaoxiao; Mei, Yueni; Huang, Yunhui

    2015-04-21

    The development of advanced energy storage devices is at the forefront of research geared towards a sustainable future. Nanostructured materials are advantageous in offering huge surface to volume ratios, favorable transport features, and attractive physicochemical properties. They have been extensively explored in various fields of energy storage and conversion. This review is focused largely on the recent progress in nanostructured Mo-based electrode materials including molybdenum oxides (MoO(x), 2 ≤ x ≤ 3), dichalconides (MoX2, X = S, Se), and oxysalts for rechargeable lithium/sodium-ion batteries, Mg batteries, and supercapacitors. Mo-based compounds including MoO2, MoO3, MoO(3-y) (0 energy storage systems because of their unique physicochemical properties, such as conductivity, mechanical and thermal stability, and cyclability. In this review, we aim to provide a systematic summary of the synthesis, modification, and electrochemical performance of nanostructured Mo-based compounds, as well as their energy storage applications in lithium/sodium-ion batteries, Mg batteries, and pseudocapacitors. The relationship between nanoarchitectures and electrochemical performances as well as the related charge-storage mechanism is discussed. Moreover, remarks on the challenges and perspectives of Mo-containing compounds for further development in electrochemical energy storage applications are proposed. This review sheds light on the sustainable development of advanced rechargeable batteries and supercapacitors with nanostructured Mo-based electrode materials.

  17. Magnetic Sensors Based on Amorphous Ferromagnetic Materials: A Review.

    Science.gov (United States)

    Morón, Carlos; Cabrera, Carolina; Morón, Alberto; García, Alfonso; González, Mercedes

    2015-11-11

    Currently there are many types of sensors that are used in lots of applications. Among these, magnetic sensors are a good alternative for the detection and measurement of different phenomena because they are a "simple" and readily available technology. For the construction of such devices there are many magnetic materials available, although amorphous ferromagnetic materials are the most suitable. The existence in the market of these materials allows the production of different kinds of sensors, without requiring expensive manufacture investments for the magnetic cores. Furthermore, these are not fragile materials that require special care, favouring the construction of solid and reliable devices. Another important feature is that these sensors can be developed without electric contact between the measuring device and the sensor, making them especially fit for use in harsh environments. In this review we will look at the main types of developed magnetic sensors. This work presents the state of the art of magnetic sensors based on amorphous ferromagnetic materials used in modern technology: security devices, weapon detection, magnetic maps, car industry, credit cards, etc.

  18. Ground-Based Research within NASA's Materials Science Program

    Science.gov (United States)

    Gillies, Donald C.; Curreri, Peter (Technical Monitor)

    2002-01-01

    Ground-based research in Materials Science for NASA's Microgravity program serves several purposes, and includes approximately four Principal Investigators for every one in the flight program. While exact classification is difficult. the ground program falls roughly into the following categories: (1) Intellectual Underpinning of the Flight Program - Theoretical Studies; (2) Intellectual Underpinning of the Flight Program - Bringing to Maturity New Research; (3) Intellectual Underpinning of the Flight Program - Enabling Characterization; (4) Intellectual Underpinning of the Flight Program - Thermophysical Property Determination; (5) Radiation Shielding; (6) Preliminary In Situ Resource Utilization; (7) Biomaterials; (8) Nanostructured Materials; (9) Materials Science for Advanced Space Propulsion. It must be noted that while the first four categories are aimed at using long duration low gravity conditions, the other categories pertain more to more recent NASA initiatives in materials science. These new initiatives address NASA's future materials science needs in the realms of crew health and safety, and exploration, and have been included in the most recent NASA Research Announcements (NRA). A description of each of these nine categories will be given together with examples of the kinds of research being undertaken.

  19. Magnetic Sensors Based on Amorphous Ferromagnetic Materials: A Review

    Directory of Open Access Journals (Sweden)

    Carlos Morón

    2015-11-01

    Full Text Available Currently there are many types of sensors that are used in lots of applications. Among these, magnetic sensors are a good alternative for the detection and measurement of different phenomena because they are a “simple” and readily available technology. For the construction of such devices there are many magnetic materials available, although amorphous ferromagnetic materials are the most suitable. The existence in the market of these materials allows the production of different kinds of sensors, without requiring expensive manufacture investments for the magnetic cores. Furthermore, these are not fragile materials that require special care, favouring the construction of solid and reliable devices. Another important feature is that these sensors can be developed without electric contact between the measuring device and the sensor, making them especially fit for use in harsh environments. In this review we will look at the main types of developed magnetic sensors. This work presents the state of the art of magnetic sensors based on amorphous ferromagnetic materials used in modern technology: security devices, weapon detection, magnetic maps, car industry, credit cards, etc.

  20. Magnetic Sensors Based on Amorphous Ferromagnetic Materials: A Review

    Science.gov (United States)

    Morón, Carlos; Cabrera, Carolina; Morón, Alberto; García, Alfonso; González, Mercedes

    2015-01-01

    Currently there are many types of sensors that are used in lots of applications. Among these, magnetic sensors are a good alternative for the detection and measurement of different phenomena because they are a “simple” and readily available technology. For the construction of such devices there are many magnetic materials available, although amorphous ferromagnetic materials are the most suitable. The existence in the market of these materials allows the production of different kinds of sensors, without requiring expensive manufacture investments for the magnetic cores. Furthermore, these are not fragile materials that require special care, favouring the construction of solid and reliable devices. Another important feature is that these sensors can be developed without electric contact between the measuring device and the sensor, making them especially fit for use in harsh environments. In this review we will look at the main types of developed magnetic sensors. This work presents the state of the art of magnetic sensors based on amorphous ferromagnetic materials used in modern technology: security devices, weapon detection, magnetic maps, car industry, credit cards, etc. PMID:26569244

  1. ASN.1 notation for exchange of data in computer-based railway control systems

    Directory of Open Access Journals (Sweden)

    Zbigniew ŁUKASIK

    2009-01-01

    Full Text Available Development of railway control systems aims at computerization. In most cases these systems are Distributed Real Time Systems. However, a huge problem in their putting into practice is the lack of interface standardization in the range of data structures and information exchange methods. It results in a variety of solutions, and thus in problems concerning cooperation of systems that come from different software vendors. Specification of protocols for data exchanging applications should therefore be created with the use of generally accepted standards. One of them is ASN.1 (Abstract Syntax Notation One language, which shall be presented in this article.

  2. Characterization of exchange rate regimes based on scaling and correlation properties of volatility for ASEAN-5 countries

    Science.gov (United States)

    Muniandy, Sithi V.; Uning, Rosemary

    2006-11-01

    Foreign currency exchange rate policies of ASEAN member countries have undergone tremendous changes following the 1997 Asian financial crisis. In this paper, we study the fractal and long-memory characteristics in the volatility of five ASEAN founding members’ exchange rates with respect to US dollar. The impact of exchange rate policies implemented by the ASEAN-5 countries on the currency fluctuations during pre-, mid- and post-crisis are briefly discussed. The time series considered are daily price returns, absolute returns and aggregated absolute returns, each partitioned into three segments based on the crisis regimes. These time series are then modeled using fractional Gaussian noise, fractionally integrated ARFIMA (0,d,0) and generalized Cauchy process. The first two stationary models provide the description of long-range dependence through Hurst and fractional differencing parameter, respectively. Meanwhile, the generalized Cauchy process offers independent estimation of fractal dimension and long memory exponent. In comparison, among the three models we found that the generalized Cauchy process showed greater sensitivity to transition of exchange rate regimes that were implemented by ASEAN-5 countries.

  3. Open inquiry-based learning experiences: a case study in the context of energy exchange by thermal radiation

    Science.gov (United States)

    Pizzolato, Nicola; Fazio, Claudio; Rosario Battaglia, Onofrio

    2014-01-01

    An open inquiry (OI)-based teaching/learning experience, regarding a scientific investigation of the process of energy exchange by thermal radiation, is presented. A sample of upper secondary school physics teachers carried out this experience at the University of Palermo, Italy, in the framework of ESTABLISH, a FP7 European Project aimed at promoting and developing inquiry-based science education. The teachers had the opportunity to personally experience an OI-based learning activity, with the aim of exploring the pedagogical potentialities of this teaching approach to promote both the understanding of difficult concepts and a deeper view of scientific practices. The teachers were firstly engaged in discussions concerning real-life problematic situations, and then stimulated to design and carry out their own laboratory activities, aimed at investigating the process of energy exchange by thermal radiation. A scientific study on the energy exchange between a powered resistor and its surrounding environment, during the heating and cooling processes, was designed and performed. Here we report the phases of this experiment by following the teachers' perspective. A structured interview conducted both before and after the OI experience allowed us to analyze and point out the teachers' feedback from a pedagogical point of view. The advantages and limits of an OI-based approach to promote the development of more student-centred inquiry-oriented teaching strategies are finally discussed.

  4. The elution of metal cyanocomplexes from polyacrylic - and polystyrene- based ion exchange resins using nitrate and thiocyanate eluants

    Directory of Open Access Journals (Sweden)

    J. C. Riani

    2007-09-01

    Full Text Available Ion exchange resins can potentially be applied in cyanide recycling to address growing environmental concerns over the use of cyanide during gold extraction. In the present work the elution of copper-, iron-, and zinc-cyanocomplexes from polyacrylic- and polystyrene-based resins was studied. It was found that iron and copper cyanides are easily eluted from polyacrylic- and polystyrene-based ion exchange resins using either SCN- or NO3-. However, elution of the zinc cyanide complex from polystyrene-based resins was poor when using nitrate solution as eluant. Besides, an increase in elution temperature from 25 °C to 50 °C improved the elution of iron and zinc cyanides from polystyrene-based resins using a nitrate eluant; however temperature did not have any significant effect on other metal cyanocomplexes or for elution using thiocyanate. It was therefore proposed that the optimal combination of resin-eluant was site-specific, and depends on the features of the effluent, processing temperature, eluant concentration, and ion exchange resin under consideration.

  5. Electro-active material (EAM) based bend sensors

    Science.gov (United States)

    LaComb, Ronald; LaComb, Julie

    2010-04-01

    The capability to accurately estimate strain and orientation of cables in an undersea environment is important for a multitude of applications. One way to estimate the positional location of a submersed cable is to utilize a network of distributed bend sensors providing inputs to a curve fitting algorithm. In this work commercially available bend sensors are characterized for small deflections. In addition proto-type devices are presented which can potentially improve device sensitivity. Commercially available bend sensors are based upon electro-active materials and variable resistance materials. Electro-active materials (EAM) are known for their actuator functionality but certain EAMs are capable of sensing as well. New advances in materials such as Ionic Polymer Metal Composites (IPMC) are proving suitable for quasi-static sensor applications. These sensors are low power, conformal and produce directionally dependent output voltages which are linearly proportional to deflection, with voltage polarity representative of the deflection direction. IPMCs are capable of being morphed for increased sensitivity. Variable resistivity sensors are based on smart epoxy polymer and carbon loaded inks. These sensors are inexpensive and conformal and unlike EAMs provide static measurements.

  6. A common basis for facilitated legitimate exchange of biological materials proposed by the European Culture Collections' Organisation

    Directory of Open Access Journals (Sweden)

    Dagmar Fritze

    2009-12-01

    Full Text Available Being charged with the task of accessioning and supplying of living microbiological material, microbial culture collections are institutions that play a central role between the interests of a variety of user communities. On the one side are the providers of living microbiological material, such as individual scientists, institutions and countries of origin and on the other side are the various kinds of recipients/users of cultures of microorganisms from academia and industry. Thus, providing access to high quality biological material and scientific services while at the same time observing donor countries' rights, intellectual property rights, biosafety and biosecurity aspects poses demanding challenges. E.g. donor countries rights relate to Article 15 of the Convention on Biological Diversity: "Contracting parties …. recognize the sovereign rights of states over their natural resources …. shall facilitate access to resources … and not impose restrictions that run counter to the aims of the Convention. Access to natural resources shall be by mutually agreed terms and subject to prior informed consent ..." The use of a proposed standard contract by culture collections is discussed as a way of contractually safeguarding the existing research commons, while observing the new rights established in the Convention on Biological Diversity as well as other existing and new legislation impacting on the accessibility of living microbial material.

  7. RECYCLING RECOVERED WOOD-BASED MATERIALS. FLATNESS, MOR AND MOE OF PANELS MADE FROM RECOVERED WOODEN BASED MATERIALS

    Directory of Open Access Journals (Sweden)

    Andrea DEÁK

    2015-12-01

    Full Text Available The objective of the research was to study the mechanical properties of recovered solid wood and wood-based materials, to create new panels made of strips of recovered oak and spruce wood, particleboards and blockboards and to study their mechanical properties, feasibility and use. Flatness, MOR and MOE were determined for the solid wood and wood-based materials recovered from construction and demolition sites. Four types of experimental panels (PL1, PL2, PALL1 and PALL2 were manufactured from solid wood strips alternating with either particleboard or blockboard strips glued edge to edge. Some of their physical and mechanical properties were investigated. All new panels made from recovered materials fell within allowable limits specified in European standard requirements for panel flatness. Panels type PL2, PALL1 and PALL2 show better values for MoR and MoE parallel to the grain when compared to the respective values for the recovered wood-based materials of which they are made, but panels type PL1 show no change. Panels type PALL2 are preferable to panels type PALL1 due to better mechanical properties. Panels type PL1 and PL2 show no such differences in their structure. The results also show that these new panels can be used successfully in furniture production, provided panels type PL1, PL2 ad PALL1 do not bear loads perpendicular to the grain or receive reinforcing elements.

  8. RIM as the data base management system for a material properties data base

    Science.gov (United States)

    Karr, P. H.; Wilson, D. J.

    1984-01-01

    Relational Information Management (RIM) was selected as the data base management system for a prototype engineering materials data base. The data base provides a central repository for engineering material properties data, which facilitates their control. Numerous RIM capabilities are exploited to satisfy prototype data base requirements. Numerical, text, tabular, and graphical data and references are being stored for five material types. Data retrieval will be accomplished both interactively and through a FORTRAN interface. The experience gained in creating and exercising the prototype will be used in specifying requirements for a production system.

  9. Seismic wavefield imaging based on the replica exchange Monte Carlo method

    Science.gov (United States)

    Kano, Masayuki; Nagao, Hiromichi; Ishikawa, Daichi; Ito, Shin-ichi; Sakai, Shin'ichi; Nakagawa, Shigeki; Hori, Muneo; Hirata, Naoshi

    2017-01-01

    Earthquakes sometimes cause serious disasters not only directly by ground motion itself but also secondarily by infrastructure damage, particularly in densely populated urban areas that have capital functions. To reduce the number and severity of secondary disasters, it is important to evaluate seismic hazards rapidly by analysing the seismic responses of individual structures to input ground motions. We propose a method that integrates physics-based and data-driven approaches in order to obtain a seismic wavefield for use as input to a seismic response analysis. The new contribution of this study is the use of the replica exchange Monte Carlo (REMC) method, which is one of the Markov chain Monte Carlo (MCMC) methods, for estimation of a seismic wavefield, together with a 1-D local subsurface structure and source information. Numerical tests were conducted to verify the proposed method, using synthetic observation data obtained from analytical solutions for two horizontally layered subsurface structure models. The geometries of the observation sites were determined from the dense seismic observation array called the Metropolitan Seismic Observation network, which has been in operation in the Tokyo metropolitan area in Japan since 2007. The results of the numerical tests show that the proposed method is able to search the parameters related to the source and the local subsurface structure in a broader parameter space than the Metropolis method, which is an ordinary MCMC method. The proposed method successfully reproduces a seismic wavefield consistent with a true wavefield. In contrast, ordinary kriging, which is a classical data-driven interpolation method for spatial data, is hardly able to reproduce a true wavefield, even in the low frequency bands. This suggests that it is essential to employ both physics-based and data-driven approaches in seismic wavefield imaging, utilizing seismograms from a dense seismic array. The REMC method, which provides not only

  10. High-Pressure Design of Advanced BN-Based Materials

    Directory of Open Access Journals (Sweden)

    Oleksandr O. Kurakevych

    2016-10-01

    Full Text Available The aim of the present review is to highlight the state of the art in high-pressure design of new advanced materials based on boron nitride. Recent experimental achievements on the governing phase transformation, nanostructuring and chemical synthesis in the systems containing boron nitride at high pressures and high temperatures are presented. All these developments allowed discovering new materials, e.g., ultrahard nanocrystalline cubic boron nitride (nano-cBN with hardness comparable to diamond, and superhard boron subnitride B13N2. Thermodynamic and kinetic aspects of high-pressure synthesis are described based on the data obtained by in situ and ex situ methods. Mechanical and thermal properties (hardness, thermoelastic equations of state, etc. are discussed. New synthetic perspectives, combining both soft chemistry and extreme pressure–temperature conditions are considered.

  11. [PROGRESS OF ALGINATE DERIVATIVES BASED ON BIOMEDICAL MATERIALS].

    Science.gov (United States)

    Wei, Xiaojuan; Gu, Qisheng; Wang, Qingsheng; Xiao, Jimin

    2015-04-01

    To summarize the current research status of alginate derivatives based on biomedical materials, and analyze several key points as novel clinical products. The general preparation and application methods of alginate derivatives based on biomedical materials at home and abroad were reviewed. The present status and problems were analyzed. The derivation methods to prepare alginate derivatives include crosslink, sulfation, biological factors derivatization, hydrophobic modification, and graft copolymerization. With excellent bionic performance of structure and properties, many alginate derivatives are available for tissue engineering scaffolds, artificial organs, and drug delivery systems etc. However, more systematic applied basic research data should be collected and statistically analyzed for risk managements. Alginate derivatives have good feasibility as novel medical products, meanwhile, systematic evaluation and verification should be executed for their safety, effectiveness, and suitability.

  12. Perovskite- and Heusler based materials for thermoelectric converters

    Science.gov (United States)

    Weidenkaff, Anke

    2015-03-01

    The broad application of thermoelectric converters in future energy technologies requires the development of active, stable, low cost and sustainable materials. Semiconductors based on perovskite and heusler structures show substantial potential for thermoelectric energy conversion processes. Their good performance can be explained based on their suitable band structure, adjusted charge carrier density, mass and mobility, limited phonon transport, electron filtering possibilities, strongly correlated electronic systems, etc. These properties are widely tuneable by following theoretical concepts and a deep composition-structure-property understanding to change the composition, structure and size of the crystallites in innovative scalable synthesis procedures. Improved thermoelectric materials are developed, synthesised and tested in diverse high temperature applications to improve the efficiency and energy density of the thermoelectric conversion process. The lecture will provide a summary on the field of advanced perovskite-type ceramics and Heusler compounds gaining importance for a large number of future energy technologies.

  13. Material identification based upon energy-dependent attenuation of neutrons

    Science.gov (United States)

    Marleau, Peter

    2015-10-06

    Various technologies pertaining to identifying a material in a sample and imaging the sample are described herein. The material is identified by computing energy-dependent attenuation of neutrons that is caused by presence of the sample in travel paths of the neutrons. A mono-energetic neutron generator emits the neutron, which is downscattered in energy by a first detector unit. The neutron exits the first detector unit and is detected by a second detector unit subsequent to passing through the sample. Energy-dependent attenuation of neutrons passing through the sample is computed based upon a computed energy of the neutron, wherein such energy can be computed based upon 1) known positions of the neutron generator, the first detector unit, and the second detector unit; or 2) computed time of flight of neutrons between the first detector unit and the second detector unit.

  14. Bulk Material Based Thermoelectric Energy Harvesting for Wireless Sensor Applications

    Energy Technology Data Exchange (ETDEWEB)

    Wang, W S; Magnin, W; Wang, N; Hayes, M; O' Flynn, B; O' Mathuna, C, E-mail: wensi.wang@tyndall.ie [Tyndall National Institute, Dyke Parade, Cork (Ireland)

    2011-08-17

    The trend towards smart building and modern manufacturing demands ubiquitous sensing in the foreseeable future. Self-powered Wireless sensor networks (WSNs) are essential for such applications. This paper describes bulk material based thermoelectric generator (TEG) design and implementation for WSN. A 20cm{sup 2} Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} based TEG was created with optimized configuration and generates 2.7mW in typical condition. A novel load matching method is used to maximize the power output. The implemented power management module delivers 651{mu}W to WSN in 50 deg. C. With average power consumption of Tyndall WSN measured at 72{mu}W, feasibility of utilizing bulk material TEG to power WSN is demonstrated.

  15. Transport studies in graphene-based materials and structures

    OpenAIRE

    Hu, Jiuning

    2015-01-01

    Graphene, a single atomic layer of graphite, has emerged as one of the most attractive materials in recent years for its many unique and excellent properties, inviting a broad area of fundamental studies and applications. In this thesis, we present some theoretical/experimental studies about the thermal, electronic and thermoelectric transport properties in graphene-based systems. We employ the molecular dynamic simulations to study the thermal transport in graphene nanoribbons (GNRs) exhibit...

  16. Mass exchange in an experimental new-generation life support system model based on biological regeneration of environment

    Science.gov (United States)

    Tikhomirov, A. A.; Ushakova, S. A.; Manukovsky, N. S.; Lisovsky, G. M.; Kudenko, Yu. A.; Kovalev, V. S.; Gubanov, V. G.; Barkhatov, Yu. V.; Gribovskaya, I. V.; Zolotukhin, I. G.; Gros, J. B.; Lasseur, Ch.

    the system. The proposed experimental model of a biological system is discussed as a candidate for potential application in the investigations aimed at creating ecosystems with largely closed cycles of the internal mass exchange. The formation and maintenance of sustainable cycling of vitally important chemical elements and compounds in biological life support systems (BLSS) is an extremely pressing problem. To attain the stable functioning of biological life support systems (BLSS) and to maintain a high degree of closure of material cycles in than, it is essential to understand the character of mass exchange processes and stoichiometnc proportions of the initial and synthesized components of the system.

  17. Leader-Member Exchange, Organization-Based Self-Esteem, and Task Performance-A Life-Stage Perspective-

    OpenAIRE

    鄭,有希

    2013-01-01

    Drawing on the leader-member exchange(LMX)theory and the intelligent career theory, we propose that a subordinates’age moderates the relationship between the quality of LMX and task performance. In addition, the study hypothesizes that organization-based self-esteem(OBSE)mediates the moderating effect of age on the relationship between the LMX quality and subordinate task performance, from the self-esteem perspective.

  18. Single interval longwave radiation scheme based on the net exchanged rate decomposition with bracketing

    Czech Academy of Sciences Publication Activity Database

    Geleyn, J.- F.; Mašek, Jan; Brožková, Radmila; Kuma, P.; Degrauwe, D.; Hello, G.; Pristov, N.

    2017-01-01

    Roč. 143, č. 704 (2017), s. 1313-1335 ISSN 0035-9009 R&D Projects: GA MŠk(CZ) LO1415 Keywords : numerical weather prediction * climate models * clouds * parameterization * atmospheres * formulation * absorption * scattering * accurate * database * longwave radiative transfer * broadband approach * idealized optical paths * net exchanged rate decomposition * bracketing * selective intermittency Impact factor: 3.444, year: 2016

  19. Error Made in Conversation by Indonesian Learners Learning English Based on Syntax and Exchanging Information

    Directory of Open Access Journals (Sweden)

    Melania Wiannastiti

    2014-10-01

    Full Text Available In learning a second language or foreign language (L2, learners should master the competences. Normally, L2 learners first should master the linguistic competence which includes the mastery of vocabularies, pronunciation, and grammar. The study is to find out the syntax error made by L2 learners in conversation as well as to find out the exchanging information. The data were the recording conversation of Visual Communication Design students first semester of Binus University joining English Entrant. Error analysis was used to analyze the data. There are two points of view to analyze the data: syntax from taxonomy and exchanging information. Taxonomy employs the error in omission, addition, misinformation, and mis-ordering. Exchanging information point of view employs the error in finite element and mood. The result shows that L2 learners made some errors in grammar and exchanging information because they are influenced by the L1. They tend to transfer from L1 to L2 rather than thinking to create the utterances in L2. 

  20. Are Students Genuinely Concerned About Recycling? Based on a Sampling of Online Exchanges, They Are...

    Science.gov (United States)

    Campus Activities Programming, 1995

    1995-01-01

    Online exchanges regarding campus-related recycling needs and efforts are excerpted here. Requests for information and responses, from both college students and administrators, concern ways to recycle when services are not available on campus, starting a recycling business, and program types in existence. (MSE)

  1. Development of a broad-host-range sacB-based vector for unmarked allelic exchange

    Directory of Open Access Journals (Sweden)

    Marx Christopher J

    2008-02-01

    Full Text Available Abstract Background Although genome sequences are available for an ever-increasing number of bacterial species, the availability of facile genetic tools for physiological analysis have generally lagged substantially behind traditional genetic models. Results Here I describe the development of an improved, broad-host-range "in-out" allelic exchange vector, pCM433, which permits the generation of clean, marker-free genetic manipulations. Wild-type and mutant alleles were reciprocally exchanged at three loci in Methylobacterium extorquens AM1 in order to demonstrate the utility of pCM433. Conclusion The broad-host-range vector for marker-free allelic exchange described here, pCM433, has the advantages of a high copy, general Escherichia coli replicon for easy cloning, an IncP oriT enabling conjugal transfer, an extensive set of restriction sites in its polylinker, three antibiotic markers, and sacB (encoding levansucrase for negative selection upon sucrose plates. These traits should permit pCM433 to be broadly applied across many bacterial taxa for marker-free allelic exchange, which is particularly important if multiple manipulations or more subtle genetic manipulations such as point mutations are desired.

  2. An improved shuffled frog leaping algorithm based evolutionary framework for currency exchange rate prediction

    Science.gov (United States)

    Dash, Rajashree

    2017-11-01

    Forecasting purchasing power of one currency with respect to another currency is always an interesting topic in the field of financial time series prediction. Despite the existence of several traditional and computational models for currency exchange rate forecasting, there is always a need for developing simpler and more efficient model, which will produce better prediction capability. In this paper, an evolutionary framework is proposed by using an improved shuffled frog leaping (ISFL) algorithm with a computationally efficient functional link artificial neural network (CEFLANN) for prediction of currency exchange rate. The model is validated by observing the monthly prediction measures obtained for three currency exchange data sets such as USD/CAD, USD/CHF, and USD/JPY accumulated within same period of time. The model performance is also compared with two other evolutionary learning techniques such as Shuffled frog leaping algorithm and Particle Swarm optimization algorithm. Practical analysis of results suggest that, the proposed model developed using the ISFL algorithm with CEFLANN network is a promising predictor model for currency exchange rate prediction compared to other models included in the study.

  3. High temperature corrosion of advanced ceramic materials for hot gas filters. Topical report for part 1 of high temperature corrosion of advanced ceramic materials for hot gas filters and heat exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Spear, K.E.; Crossland, C.E.; Shelleman, D.L.; Tressler, R.E. [Pennsylvania State Univ., University Park, PA (United States). Dept. of Materials Science and Engineering

    1997-12-11

    This program consists of two separate research areas. Part 1, for which this report is written, studied the high temperature corrosion of advanced ceramic hot gas filters, while Part 2 studied the long-term durability of ceramic heat exchangers to coal combustion environments. The objectives of Part 1 were to select two candidate ceramic filter materials for flow-through hot corrosion studies and subsequent corrosion and mechanical properties characterization. In addition, a thermodynamic database was developed so that thermochemical modeling studies could be performed to simulate operating conditions of laboratory reactors and existing coal combustion power plants, and to predict the reactions of new filter materials with coal combustion environments. The latter would make it possible to gain insight into problems that could develop during actual operation of filters in coal combustion power plants so that potential problems could be addressed before they arise.

  4. Barter exchanges

    DEFF Research Database (Denmark)

    Sudzina, Frantisek

    Although barter is often perceived as something that proceeded money, barter is still used. The focus of the paper is on barter exchanges. Barter exchanges are used both in developing countries as well as in developed countries (including the U.S.). They are used by both organizations...... and individuals. They usually allow to exchange good but some include also services. Some exchanges allow only for bi-directional barter, i.e. when only two parties are involved in the exchange. But probably most of the barter exchanges use barter money; this makes it easier to exchange goods and services...

  5. Experimental process investigation of a latent heat energy storage system with a staggered heat exchanger with different phase change materials for solar thermal energy storage applications

    Science.gov (United States)

    Tsolakoglou, Nikolas P.; Koukou, Maria K.; Vrachopoulos, Michalis Gr.; Tachos, Nikolaos; Lymberis, Kostas; Stathopoulos, Vassilis

    2017-11-01

    This work investigates melting and solidification processes of four different Phase Change Materials (PCM) used as latent heat thermal storage system. The experimental rig was consisted of an insulated tank, filled with the under investigation PCM, a staggered heat exchanger to supply or extract heat from the PCM cavity and a water pump to circulate Heat Transfer Fluid (HTF). Both charging (melting) and discharging (solidification) processes were conducted for two different HTF flow rates. The main scope of this work was to develop a first approach and to investigate the behaviour of PCM under various load conditions (different HTF flow rates). Results show that different HTF flow rates affect melting and solidification time periods; in both processes time was reduced while HTF flow rate was increased but in differentways due to the transition from conduction to convection heat transfer mechanisms.

  6. Nanoporous Carbide-Derived Carbon Material-Based Linear Actuators

    Directory of Open Access Journals (Sweden)

    Janno Torop

    2009-12-01

    Full Text Available Devices using electroactive polymer-supported carbon material can be exploited as alternatives to conventional electromechanical actuators in applications where electromechanical actuators have some serious deficiencies. One of the numerous examples is precise microactuators. In this paper, we show for first time the dilatometric effect in nanocomposite material actuators containing carbide-derived carbon (CDC and polytetrafluoroetylene polymer (PTFE. Transducers based on high surface area carbide-derived carbon electrode materials are suitable for short range displacement applications, because of the proportional actuation response to the charge inserted, and high Coulombic efficiency due to the EDL capacitance. The material is capable of developing stresses in the range of tens of N cm-2. The area of an actuator can be dozens of cm2, which means that forces above 100 N are achievable. The actuation mechanism is based on the interactions between the high-surface carbon and the ions of the electrolyte. Electrochemical evaluations of the four different actuators with linear (longitudinal action response are described. The actuator electrodes were made from two types of nanoporous TiC-derived carbons with surface area (SA of 1150 m2 g-1 and 1470 m2 g-1, respectively. Two kinds of electrolytes were used in actuators: 1.0 M tetraethylammonium tetrafluoroborate (TEABF4 solution in propylene carbonate and pure ionic liquid 1-ethyl-3-methylimidazolium trifluoromethanesulfonate (EMITf. It was found that CDC based actuators exhibit a linear movement of about 1% in the voltage range of 0.8 V to 3.0 V at DC. The actuators with EMITf electrolyte had about 70% larger movement compared to the specimen with TEABF4 electrolyte.

  7. Learning material recommendation based on case-based reasoning similarity scores

    Science.gov (United States)

    Masood, Mona; Mokmin, Nur Azlina Mohamed

    2017-10-01

    A personalized learning material recommendation is important in any Intelligent Tutoring System (ITS). Case-based Reasoning (CBR) is an Artificial Intelligent Algorithm that has been widely used in the development of ITS applications. This study has developed an ITS application that applied the CBR algorithm in the development process. The application has the ability to recommend the most suitable learning material to the specific student based on information in the student profile. In order to test the ability of the application in recommending learning material, two versions of the application were created. The first version displayed the most suitable learning material and the second version displayed the least preferable learning material. The results show the application has successfully assigned the students to the most suitable learning material.

  8. Modification of clay-based waste containment materials

    Energy Technology Data Exchange (ETDEWEB)

    Adu-Wusu, K. [DuPont Central Research and Development, Newark, DE (United States); Whang, J.M. [DuPont Specialty Chemicals, Deepwater, NJ (United States); McDevitt, M.F. [DuPont Central Research and Development, Wilmington, DE (United States)

    1997-12-31

    Bentonite clays are used extensively for waste containment barriers to help impede the flow of water in the subsurface because of their low permeability characteristics. However, they do little to prevent diffusion of contaminants, which is the major transport mechanism at low water flows. A more effective way of minimizing contaminant migration in the subsurface is to modify the bentonite clay with highly sorptive materials. Batch sorption studies were conducted to evaluate the sorptive capabilities of organo-clays and humic- and iron-based materials. These materials proved to be effective sorbents for the organic contaminants 1,2,4-trichlorobenzene, nitrobenzene, and aniline in water, humic acid, and methanol solution media. The sorption capacities were several orders of magnitude greater than that of unmodified bentonite clay. Modeling results indicate that with small amounts of these materials used as additives in clay barriers, contaminant flux through walls could be kept very small for 100 years or more. The cost of such levels of additives can be small compared to overall construction costs.

  9. Cathodoluminescence Emission Studies for Selected Phosphor-Based Sensor Materials

    Energy Technology Data Exchange (ETDEWEB)

    Goedeke, Shawn [ORNL; Hollerman, William Andrew [ORNL; Allison, Stephen W [ORNL; Gray, P A [Integrated Concepts and Research Corporation - Huntsville, AL; Lewis, Linda A [ORNL; Smithwick III, Robert W [ORNL; Boatner, Lynn A [ORNL; Glasgow, David C [ORNL; Ivanov, Ilia N [ORNL; Wise, H. [Integrated Concepts and Research Corporation - Huntsville, AL

    2005-01-01

    The current interest in returning to the Moon and Mars by 2030 makes cost effective and low mass health monitoring sensors essential for spacecraft development. In space, there are many surface measurements that are required to monitor the condition of the spacecraft including: surface temperature, radiation dose, and impact. Through the use of phosphors, these conditions can be monitored. Practical space-based phosphor sensors will depend heavily upon research investigating the resistance of phosphors to ionizing radiation and the ability to anneal or self-heal from damage caused by ionizing radiation. The cathodoluminescence (CL) testing was performed using the low energy electron system located at the NASA Marshall Space Flight Center (MSFC) in Huntsville, Alabama. For the materials tested, several interesting results were observed. For most materials, increases in both beam energy and current density improved the CL fluorescence yield. It was also noted that YAG:Nd,Ce has the greatest near infrared intensity for any of the tested materials. The evaluation of dopant concentration in YPO{sub 4}:Nd showed minimal differences in spectral shape and intensity. While the total electron dose was small, the intention was to maximize the number of irradiated materials.

  10. Advanced Materials Based on Polymers and Ionic Liquids.

    Science.gov (United States)

    Kitazawa, Yuzo; Ueno, Kazuhide; Watanabe, Masayoshi

    2017-09-19

    Ionic liquids (ILs) are ambient temperature molten salts, which have attracted considerable attention owing to their unique properties. In this contribution, we review advanced materials composed of ILs and polymers for the basis of a new design protocol to fabricate novel materials. As electrolytes for electrochemical devices, cross-linked polymers containing ILs (ion gels) are endowed with functional properties inherited from ILs and mechanical consistency derived from polymers. To create such materials, micro-phase separation of block copolymers and colloidal arrays in the ILs are utilized. Based on the molecular design of task-specific ILs, the resultant ion gels are applicable as electrolytes for actuator, fuel cell, and secondary battery applications. Thermo- and photo-responsive polymers in ILs are also highlighted, whereby such stimuli elicit changes in the solubility of the self-assembly of block copolymers and colloidal arrays in the ILs. Further, thermo- and photo-reversible changes in the self-assembled structure can be exploited to demonstrate sol-gel transitions and fabricate photo-healable materials. © 2017 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. The tissue micro-array data exchange specification: a web based experience browsing imported data

    Directory of Open Access Journals (Sweden)

    Ayers Leona W

    2005-08-01

    Full Text Available Abstract Background The AIDS and Cancer Specimen Resource (ACSR is an HIV/AIDS tissue bank consortium sponsored by the National Cancer Institute (NCI Division of Cancer Treatment and Diagnosis (DCTD. The ACSR offers to approved researchers HIV infected biologic samples and uninfected control tissues including tissue cores in micro-arrays (TMA accompanied by de-identified clinical data. Researchers interested in the type and quality of TMA tissue cores and the associated clinical data need an efficient method for viewing available TMA materials. Because each of the tissue samples within a TMA has separate data including a core tissue digital image and clinical data, an organized, standard approach to producing, navigating and publishing such data is necessary. The Association for Pathology Informatics (API extensible mark-up language (XML TMA data exchange specification (TMA DES proposed in April 2003 provides a common format for TMA data. Exporting TMA data into the proposed format offers an opportunity to implement the API TMA DES. Using our public BrowseTMA tool, we created a web site that organizes and cross references TMA lists, digital "virtual slide" images, TMA DES export data, linked legends and clinical details for researchers. Microsoft Excel® and Microsoft Word® are used to convert tabular clinical data and produce an XML file in the TMA DES format. The BrowseTMA tool contains Extensible Stylesheet Language Transformation (XSLT scripts that convert XML data into Hyper-Text Mark-up Language (HTML web pages with hyperlinks automatically added to allow rapid navigation. Results Block lists, virtual slide images, legends, clinical details and exports have been placed on the ACSR web site for 14 blocks with 1623 cores of 2.0, 1.0 and 0.6 mm sizes. Our virtual microscope can be used to view and annotate these TMA images. Researchers can readily navigate from TMA block lists to TMA legends and to clinical details for a selected tissue core

  12. Development of antimicrobial active packaging materials based on gluten proteins.

    Science.gov (United States)

    Gómez-Heincke, Diana; Martínez, Inmaculada; Partal, Pedro; Guerrero, Antonio; Gallegos, Críspulo

    2016-08-01

    The incorporation of natural biocide agents into protein-based bioplastics, a source of biodegradable polymeric materials, manufactured by a thermo-mechanical method is a way to contribute to a sustainable food packaging industry. This study assesses the antimicrobial activity of 10 different biocides incorporated into wheat gluten-based bioplastics. The effect that formulation, processing, and further thermal treatments exert on the thermo-mechanical properties, water absorption characteristics and rheological behaviour of these materials is also studied. Bioplastics containing six of the 10 examined bioactive agents have demonstrated suitable antimicrobial activity at 37 °C after their incorporation into the bioplastic. Moreover, the essential oils are able to create an antimicrobial atmosphere within a Petri dish. Depending on the selected biocide, its addition may alter the bioplastics protein network in a different extent, which leads to materials exhibiting less water uptake and different rheological and thermo-mechanical behaviours. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

  13. Investigation of graphene-based nanoscale radiation sensitive materials

    Science.gov (United States)

    Robinson, Joshua A.; Wetherington, Maxwell; Hughes, Zachary; LaBella, Michael, III; Bresnehan, Michael

    2012-06-01

    Current state-of-the-art nanotechnology offers multiple benefits for radiation sensing applications. These include the ability to incorporate nano-sized radiation indicators into widely used materials such as paint, corrosion-resistant coatings, and ceramics to create nano-composite materials that can be widely used in everyday life. Additionally, nanotechnology may lead to the development of ultra-low power, flexible detection systems that can be embedded in clothing or other systems. Graphene, a single layer of graphite, exhibits exceptional electronic and structural properties, and is being investigated for high-frequency devices and sensors. Previous work indicates that graphene-oxide (GO) - a derivative of graphene - exhibits luminescent properties that can be tailored based on chemistry; however, exploration of graphene-oxide's ability to provide a sufficient change in luminescent properties when exposed to gamma or neutron radiation has not been carried out. We investigate the mechanisms of radiation-induced chemical modifications and radiation damage induced shifts in luminescence in graphene-oxide materials to provide a fundamental foundation for further development of radiation sensitive detection architectures. Additionally, we investigate the integration of hexagonal boron nitride (hBN) with graphene-based devices to evaluate radiation induced conductivity in nanoscale devices. Importantly, we demonstrate the sensitivity of graphene transport properties to the presence of alpha particles, and discuss the successful integration of hBN with large area graphene electrodes as a means to provide the foundation for large-area nanoscale radiation sensors.

  14. Degradation of chitosan-based materials after different sterilization treatments

    Science.gov (United States)

    San Juan, A.; Montembault, A.; Gillet, D.; Say, J. P.; Rouif, S.; Bouet, T.; Royaud, I.; David, L.

    2012-02-01

    Biopolymers have received in recent years an increasing interest for their potential applications in the field of biomedical engineering. Among the natural polymers that have been experimented, chitosan is probably the most promising in view of its exceptional biological properties. Several techniques may be employed to sterilize chitosan-based materials. The aim of our study was to compare the effect of common sterilization treatments on the degradation of chitosan-based materials in various physical states: solutions, hydrogels and solid flakes. Four sterilization methods were compared: gamma irradiation, beta irradiation, exposure to ethylene oxide and saturated water steam sterilization (autoclaving). Exposure to gamma or beta irradiation was shown to induce an important degradation of chitosan, regardless of its physical state. The chemical structure of chitosan flakes was preserved after ethylene oxide sterilization, but this technique has a limited use for materials in the dry state. Saturated water steam sterilization of chitosan solutions led to an important depolymerization. Nevertheless, steam sterilization of chitosan flakes bagged or dispersed in water was found to preserve better the molecular weight of the polymer. Hence, the sterilization of chitosan flakes dispersed in water would represent an alternative step for the preparation of sterilized chitosan solutions. Alternatively, autoclaving chitosan physical hydrogels did not significantly modify the macromolecular structure of the polymer. Thus, this method is one of the most convenient procedures for the sterilization of physical chitosan hydrogels after their preparation.

  15. Recent Advances in Conjugated Polymer-Based Microwave Absorbing Materials

    Directory of Open Access Journals (Sweden)

    Ying Wang

    2017-01-01

    Full Text Available Microwave absorbing materials (MAMs are paving the way for exciting applications in electromagnetic (EM pollution precaution and national defense security, as they offer an advanced alternative to conventional reflection principles to fundamentally eliminate the EM waves. Conjugated polymer (CP-based composites appear as a promising kind of MAM with the desirable features of low density and high performance. In this review, we introduce the theory of microwave absorption and summarize recent advances in the fabrication of CP-based MAMs, including rational design of the microstructure of pure conjugated polymers and tunable chemical integration with magnetic ferrites, magnetic metals, transition metal oxides, and carbon materials. The key point of enhancing microwave absorption in CP-based MAMs is to regulate their EM properties, improve matching of characteristic impedance, and create diversified loss mechanisms. The examples presented in this review will provide new insights into the design and preparation of CP-based composites that can satisfy the high demands of the oncoming generation of MAMs.

  16. DEVELOPING ISLAMIC ENGLISH INSTRUCTIONAL MATERIALS BASED ON SCHOOL-BASED CURRICULUM

    Directory of Open Access Journals (Sweden)

    Zaitun Qamariah

    2015-09-01

    Full Text Available This study was a research and development (R&D which is basically aimed at developing English instructional materials based on School-based Curriculum for the first-year students of MAN Model Palangka Raya. This study involved: need analysis, reference study, material development, expert validation, try out (empirical validation, and revision. The data were gathered through observation, questionnaires, interview, and validation technique.  The result of the need analysis shows that the students are in need of English instructional materials relevant to their major content needs and school characteristics. However, the existing English instructional materials used by the teachers and the first-grade students of MAN Model Palangka Raya as a senior high school with Islamic feature still served from available published course books which are too general and still do not reflect the need of the students and particular characteristics of the school. English instructional materials developed in this study is intended to develop English instructional materials which could provide a set of instructional materials to accomodate the Islamic characteristics and the needs of the first-year students of MAN Model Palangka Raya. For the purpose, the materials were adopted and adapted from some Islamic textbooks and Islamic reading websites. Keywords: research and development, Islamic English instructional material, school-based curriculum

  17. Verifier-based three-party authentication schemes using extended chaotic maps for data exchange in telecare medicine information systems.

    Science.gov (United States)

    Lee, Tian-Fu

    2014-12-01

    Telecare medicine information systems provide a communicating platform for accessing remote medical resources through public networks, and help health care workers and medical personnel to rapidly making correct clinical decisions and treatments. An authentication scheme for data exchange in telecare medicine information systems enables legal users in hospitals and medical institutes to establish a secure channel and exchange electronic medical records or electronic health records securely and efficiently. This investigation develops an efficient and secure verified-based three-party authentication scheme by using extended chaotic maps for data exchange in telecare medicine information systems. The proposed scheme does not require server's public keys and avoids time-consuming modular exponential computations and scalar multiplications on elliptic curve used in previous related approaches. Additionally, the proposed scheme is proven secure in the random oracle model, and realizes the lower bounds of messages and rounds in communications. Compared to related verified-based approaches, the proposed scheme not only possesses higher security, but also has lower computational cost and fewer transmissions. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  18. Development of Web Based Learning Material in Physics Subject for Kalor and Temperature Material

    Directory of Open Access Journals (Sweden)

    Fatwa Aji Kurniawan

    2015-12-01

    Full Text Available It has been done, the research which aims to develop a web-based teaching materials on the subjects of physics subject with subject mater of temperature and heat. This study using a modified model of the 4D development by eliminating the deployment phase. The validation of product development conducted by validator media experts and experts matter of physics, whereas small-scale trials conducted by physics teacher and 10 students. Validator review results stating that the quality of the product development were included in the category very well with the average percentage rating of 83.93%. The percentage value assigned by media expert by 75% in the good category and the percentage of the value provided by a matter expert 92.85% were in the very good category. Experiments by physics teacher to obtain result of equal to 94.44% were in the very good category and the average percentage of the test results by the students of 90.5% were in the very good category. The characteristics of the products developed include material composition using the curriculum in 2013, there was a recording facility and the results of evaluation of students' activities, there were feedback evaluation results were immediately known by the students and there were some links related to the material either youtube or other learning website.

  19. A Hydrogen-Deuterium Exchange Study on Nickel-based Binary-Ternary Amorphous and Crystalline Membranes

    Science.gov (United States)

    Adibhatla, Anasuya

    Hydrogen is a major role player in current global sustainable energy scenario. Research around the world is carried out to harness hydrogen from all possible sources. One of these sources is water gas shift reaction after the coal gasification process. Sustainable infrastructure can be viable in countries like USA and Australia, making this process viable. Various methods are used to harness this hydrogen from the water gas. One of these methods is the use of inorganic membranes based on Pd, Ag, Ni, Zr and other transition metals. Pd addition to the membranes makes the membranes more expensive for commercial use. Various bulk properties like hydrogen permeation and absorption are studied on Pd and Pd-based alloys. Alternate alloys based on Ni, V, Ta etc are being studied to substitute the use of Pd making this technology more cost efficient. A current balance in research in this area is fund to exist by coating the non-precious metal membranes with Pd to improve the surface interaction with hydrogen. The nature of membranes used for hydrogen separation is important aspect for the overall performance. Crystalline materials provide better bulk properties, however, are not durable under high temperature and hydrogen pressure. In this research, non-Pd coated Ni-based amorphous membranes were made by melt spin technique, which have been studied for their surface properties. Gas phase H2-D2 exchange reaction has been carried out on the membrane surface. This provides a measure of catalytic activity of the above mentioned membranes. More studies included the crystallographic phase change determination, bulk hydrogen solubility measurements, surface conduction measurements and surface morphological studies. During this research, it has been observed that crystalline materials provide more surface activity for hydrogen than their amorphous counterparts. Ni64Zr36 alloy has been shown to exhibit similar kinetic rates as metallic Ni. Also, microkinetic analysis was performed

  20. Computer-aided process planning in prismatic shape die components based on Standard for the Exchange of Product model data

    Directory of Open Access Journals (Sweden)

    Awais Ahmad Khan

    2015-11-01

    Full Text Available Insufficient technologies made good integration between the die components in design, process planning, and manufacturing impossible in the past few years. Nowadays, the advanced technologies based on Standard for the Exchange of Product model data are making it possible. This article discusses the three main steps for achieving the complete process planning for prismatic parts of the die components. These three steps are data extraction, feature recognition, and process planning. The proposed computer-aided process planning system works as part of an integrated system to cover the process planning of any prismatic part die component. The system is built using Visual Basic with EWDraw system for visualizing the Standard for the Exchange of Product model data file. The system works successfully and can cover any type of sheet metal die components. The case study discussed in this article is taken from a large design of progressive die.

  1. Towards Flexible Transparent Electrodes Based on Carbon and Metallic Materials

    Directory of Open Access Journals (Sweden)

    Minghui Luo

    2017-01-01

    Full Text Available Flexible transparent electrodes (FTEs with high stability and scalability are in high demand for the extremely widespread applications in flexible optoelectronic devices. Traditionally, thin films of indium thin oxide (ITO served the role of FTEs, but film brittleness and scarcity of materials limit its further application. This review provides a summary of recent advances in emerging transparent electrodes and related flexible devices (e.g., touch panels, organic light-emitting diodes, sensors, supercapacitors, and solar cells. Mainly focusing on the FTEs based on carbon nanomaterials (e.g., carbon nanotubes and graphene and metal materials (e.g., metal grid and metal nanowires, we discuss the fabrication techniques, the performance improvement, and the representative applications of these highly transparent and flexible electrodes. Finally, the challenges and prospects of flexible transparent electrodes will be summarized.

  2. Development of foamed Inorganic Polymeric Materials based on Perlite

    Science.gov (United States)

    Tsaousi, G.-M.; Douni, I.; Taxiarchou, M.; Panias, D.; Paspaliaris, I.

    2016-04-01

    This work deals with the development of lightweight geopolymeric boards for use in construction sector utilizing a solid perlitic waste as the main raw material. Hydrogen peroxide (H2O2) was used for the foaming of geopolymeric pastes and the production of porous and lightweight inorganic polymeric materials. The effect of geopolymeric synthesis parameters, such as the composition of activator and the curing conditions, on paste's properties that affect the foaming process, such as setting time and viscosity, were studied in detailed. Finally, the effects of H2O2 concentration on the properties (apparent density and % cell volume) and the microstructure of foamed boards were also studied. The produced porous boards have effective densities in-between 540 - 900 Kg/m3 and the thermal conductivity of the optimum product is 0.08 W/mK. Based on their properties, the developed lightweight geopolymeric boards have high potential to be used as building elements in construction industry.

  3. Toward the Development of Cluster-Based Materials

    Energy Technology Data Exchange (ETDEWEB)

    Bowen, Kit H. [Johns Hopkins University

    1995-06-01

    Our research program provided experimental results that made fundamental, underpinning contributions to the development of cluster-based materials. Specific topics we have studied include the non-metal-to-metallic transition in divalent metal clusters, the search for (and discovery of) theoretically-predicted, ionically-bonded cluster-assembled “molecules” and other Magic Clusters, the interaction of transition metal atoms and clusters with organic molecular templates, the synthesis and characterization of Zintl phase clusters, the magnetic properties of semiconductor clusters, the molecular properties of electronic materials, the magnetic properties of silicon-encapsulated rare earth metal atom cages, and the magnetic and electronic properties of gold/silica and gold/iron clusters.

  4. REQUIREMENTS FOR DRILLING CUTTINGS AND EARTH-BASED BUILDING MATERIALS

    Directory of Open Access Journals (Sweden)

    Chertes Konstantin L'vovich

    2017-08-01

    Full Text Available In this article, the problem of utilization of drilling cuttings by means of scavenging, is researched. The product received could be used for the restoration of lands disturbed during construction and economic activities. When assessing technogenic formations, the binary approach was used, as a system of two components. The purpose of the study is to assess the state and possibility of utilizing drilling cuttings as raw materials in order to produce technogenic building materials; to study the effect of the degree of homogeneity of initial mixtures based on drilling cuttings, on kinetics of their hardening which leads to obtaining final products for various applications . As a result of research, relations of hardening and subsequent strengthening of slurry-cement mixtures were obtained; the plan of the process area for treatment of drilling cuttings is presented on the spot of demolished drilling pit.

  5. Adsorption of Bovine Serum Albumin on Carbon-Based Materials

    Directory of Open Access Journals (Sweden)

    Mykola Seredych

    2018-01-01

    Full Text Available The protein adsorption plays a very important role in biotechnology, biomolecular engineering and it is one of the main factors determining bio- and hemocompatibility of biomedical materials in medical applications, such as blood purification and wound healing. Here we report adsorption properties of two carbon-based materials, thermally expanded graphite (EGr and graphene nanoplatelets (GnP, for bovine serum albumin (BSA, the most abundant blood plasma protein. The influence of the surface chemistry of expanded graphite on the mechanism of BSA adsorption was studied by using EGr modified with oxygen or nitrogen functionalities. Having low microporosity and the specific surface area in the range of 5 to 50 m2/g, the expanded graphite exhibits high protein adsorption capacity at high equilibrium concentrations, which makes this material a potential candidate for biomedical applications as a carrier for high molecular weight (HMW drug delivery or adsorption of HMW metabolites. At low equilibrium concentrations, the effect of specific protein-surface functional groups interaction reveals the differences between the adsorption affinity of different surface modified EGr materials to BSA. The adsorption of BSA on GnP with a specific surface area of 286 m2/g and a developed micro-/mesoporous structure did not follow the same mechanism as seen with EGr materials. At low equilibrium concentration of BSA, GnP exhibits high adsorption efficiency. An important finding is that no release of nanoparticles from expanded graphite adsorbents was observed, which makes them potentially suitable for direct contact with blood and other tissues while very small nanoparticles were noticed in the case of graphene nanoplatelets.

  6. Prosthetic limb sockets from plant-based composite materials.

    Science.gov (United States)

    Campbell, Andrew I; Sexton, Sandra; Schaschke, Carl J; Kinsman, Harry; McLaughlin, Brian; Boyle, Martin

    2012-06-01

    There is a considerable demand for lower limb prostheses globally due to vascular disease, war, conflict, land mines and natural disasters. Conventional composite materials used for prosthetic limb sockets include acrylic resins, glass and carbon fibres, which produce harmful gasses and dust in their manufacture. To investigate the feasibility of using a renewable plant oil-based polycarbonate-polyurethane copolymer resin and plant fibre composite, instead of conventional materials, to improve safety and accessibility of prosthetic limb manufacture. Experimental, bench research. Test pieces of the resin with a range of plant fibres (10.0% by volume) were prepared and tensile strengths were tested. Test sockets of both conventional composite materials and plant resin with plant fibres were constructed and tested to destruction. Combinations of plant resin and either banana or ramie fibres gave high tensile strengths. The conventional composite material socket and plant resin with ramie composite socket failed at a similar loading, exceeding the ISO 10328 standard. Both wall thickness and fibre-matrix adhesion played a significant role in socket strength. From this limited study we conclude that the plant resin and ramie fibre composite socket has the potential to replace the standard layup. Further mechanical and biocompatibility testing as well as a full economic analysis is required. Using readily sourced and renewable natural fibres and a low-volatile bio-resin has potential to reduce harm to those involved in the manufacture of artificial limb sockets, without compromising socket strength and benefitting clinicians working in poorer countries where safety equipment is scarce. Such composite materials will reduce environmental impact.

  7. A novel surface-confined glucaminium-based ionic liquid stationary phase for hydrophilic interaction/anion-exchange mixed-mode chromatography.

    Science.gov (United States)

    Qiao, Lizhen; Wang, Shuangyuan; Li, Hua; Shan, Yuanhong; Dou, Abo; Shi, Xianzhe; Xu, Guowang

    2014-09-19

    Glucaminium-based ionic liquids are a new class of recently developed ionic liquids and prepared by functionalizing the amine group of N-methyl-d-glucamine, which renders them good hydrophilicity due to the presence of the glucose structure and charged quaternary ammonium group. In the present study, a glucaminium-based ionic liquid N,N-diallyl-N-methyl-d-glucaminium bromide was synthesized and subsequently bonded to the surface of 3-mercaptopropyl modified silica materials through "thiol-ene" click chemistry. The obtained stationary phase was characterized by elemental analysis and infrared spectroscopy, and then packed as a HPLC column. A mixture of five nucleosides was used to characterize the separation performance of the obtained column under HILIC mode and the column efficiency was determined with cytidine as the test solute, reaching 80,000plates/m. Then, the retention behavior was evaluated by investigating the effect of various chromatographic factors on retention of different types of solutes, and the results revealed that the developed surface-confined glucaminium-based ionic liquid stationary phase exhibited a hydrophilic interaction/anion-exchange mixed-mode retention mechanism. Finally, two mixtures of nucleotides and flavonoids were separated on the glucaminium-based ionic liquid column, respectively under hydrophilic interaction and hydrophilic interaction/anion-exchange mixed-mode chromatography. In conclusion, the multimodal retention capabilities of the glucaminium-based ionic liquid column could offer a wider range of retention behavior and flexible selectivity toward polar and hydrophilic compounds. Copyright © 2014 Elsevier B.V. All rights reserved.

  8. Multi-ionic effects on energy production based on double layer expansion by salinity exchange.

    Science.gov (United States)

    Fernández, M M; Ahualli, S; Iglesias, Guillermo R; González-Caballero, Fernando; Delgado, Ángel V; Jiménez, M L

    2015-05-15

    It has been recently shown that the free energy change upon salinity mixing in river mouths can be harvested taking advantage of the fact that the capacitance of charged solid/liquid interfaces (electrical double layers, EDLs) depends strongly on the ionic composition of the liquid medium. This has led to a new generation of techniques called Capmix technologies, one of them (CDLE or capacitive energy extraction based on DL expansion) based precisely on such dependence. Despite the solution composition playing a crucial role on the whole process, most of the research carried out so far has mainly focused on pure sodium chloride solutions. However, the effect of other species usually present in river and seawaters should be considered both theoretically and experimentally in order to succeed in optimizing a future device. In this paper, we analyse solutions of a more realistic composition from two points of view. Firstly, we find both experimentally and theoretically that the presence of ions other than sodium and chloride, even at low concentrations, may lead to a lower energy extraction in the process. Secondly, we experimentally consider the possible effects of other materials usually dispersed in natural water (mineral particles, microbes, shells, pollutants) by checking their accumulation in the carbon films used, after being exposed for a long period to natural sea water during CDLE cycles. Copyright © 2014 Elsevier Inc. All rights reserved.

  9. Marine fungi: Degraders of poly-3-hydroxyalkanoate based plastic materials

    Directory of Open Access Journals (Sweden)

    Matavulj Milan

    2009-01-01

    Full Text Available The search for new biosynthetic and biodegradable materials to save nonrenewable resources and reduce global pollution problems is an urgent task. Recently, materials like thermoplastic poly-3-hydroxyalkanoates (PHA, have been found synthesized by bacteria as storage materials. The major PHAs synthesized are poly-b-hydroxybutyrate (PHB, poly-b-hydroxyvalerate (PHV and their copolymers. They are already commercially produced and used as BIOPOLTM (ICI, England. Their complete degradability by bacteria has already been shown. Today, oceans and estuaries serve as major landfills, and since fungi are an important part of the degrading microbiota, in order to prove their participation in the degradation process, a simple degradation test suitable for fungi and marine conditions had to be developed. Several solid media based on artificial sea water, differing in the content of non-alkanoate organics and supplemented with 0.1% PHA (or BIOPOLTM as a main source of carbon have been tested. The testing principle consists of clearing the turbid medium in test tube or plates caused by suspended granules of PHA. All media tested supported the growth of fungi. For the discrete and transparent clearing of zones, a mineral medium with 0.01% peptone, 0.01% yeast extract, and 0.1% PHB or BIOPOLTM was finally chosen where the fine and evenly distributed turbidity is accomplished by a specific procedure. This method allows the investigation of degradability of PHA-based plastic materials as well as screening for fungal ability to depolymerise pure PHA homopolymers. Using this medium, 32 strains of marine yeasts and 102 strains of marine mycelial fungi belonging to different systematic and ecological groups were tested for their ability to degrade PHAs. Only about 4% of the strains were able to degrade BIOPOLTM and about 6% depolymerised pure PHB homopolymer. This is in sharp contrast to the results of our previous experiments with 143 strains of terrestrial fungi

  10. Comparison of Candida Albicans Adherence to Conventional Acrylic Denture Base Materials and Injection Molding Acrylic Materials.

    Science.gov (United States)

    Aslanimehr, Masoomeh; Rezvani, Shirin; Mahmoudi, Ali; Moosavi, Najmeh

    2017-03-01

    Candida species are believed to play an important role in initiation and progression of denture stomatitis. The type of the denture material also influences the adhesion of candida and development of stomatitis. The aim of this study was comparing the adherence of candida albicans to the conventional and injection molding acrylic denture base materials. Twenty injection molding and 20 conventional pressure pack acrylic discs (10×10×2 mm) were prepared according to their manufacturer's instructions. Immediately before the study, samples were placed in sterile water for 3 days to remove residual monomers. The samples were then sterilized using an ultraviolet light unit for 10 minutes. 1×10 8 Cfu/ml suspension of candida albicans ATCC-10231 was prepared from 48 h cultured organism on sabouraud dextrose agar plates incubated at 37oC. 100 μL of this suspension was placed on the surface of each disk. After being incubated at 37oC for 1 hour, the samples were washed with normal saline to remove non-adherent cells. Attached cells were counted using the colony count method after shaking at 3000 rmp for 20 seconds. Finally, each group was tested for 108 times and the data were statistically analyzed by t-test. Quantitative analysis revealed that differences in colony count average of candida albicans adherence to conventional acrylic materials (8.3×10 3 ) comparing to injection molding acrylic resins (6×10 3 ) were statistically significant ( p injection acrylic resin materials makes them valuable for patients with high risk of denture stomatitis.

  11. Cross-linked comb-shaped anion exchange membranes with high base stability

    Energy Technology Data Exchange (ETDEWEB)

    Li, NW; Wang, LZ; Hickner, M

    2014-01-01

    A unique one-step cross-linking strategy that connects quaternary ammonium centers using Grubbs II-catalyzed olefin metathesis was developed. The cross-linked anion exchange membranes showed swelling ratios of less than 10% and hydroxide conductivities of 18 to 40 mS cm(- 1). Cross-linking improved the membranes' stability to hydroxide degradation compared to their non-cross-linked analogues.

  12. Testing for Efficiency in Selected Developing Foreign Exchange Markets: An Equilibrium-based Approach.

    OpenAIRE

    Nikolaos Giannellis; Athanasios Papadopoulos

    2006-01-01

    This paper proposes an alternative way of testing FOREX efficiency for developing countries. The FOREX market will be efficient if fully reflects all available information. If this holds, the actual exchange rate will not deviate significantly from its equilibrium rate. Moreover, the spot rate should deviate from its equilibrium rate by only transitory components (i.e. it should follow a white noise process). This test is applied to three Central & Eastern European Countries – members of the ...

  13. Acid precipitation effects on soil pH and base saturation of exchange sites

    Science.gov (United States)

    W. W. McFee; J. M. Kelly; R. H. Beck

    1976-01-01

    The typical values and probable ranges of acid-precipitation are evaluated in terms of their theoretical effects on pH and cation exchange equilibrium of soils characteristic of the humid temperature region. The extent of probable change in soil pH and the time required to cause such a change are calculated for a range of common soils. Hydrogen ion input by acid...

  14. Layered double hydroxides as electrode materials for Ni based batteries and as novel inorganic/organic hybrid materials

    Energy Technology Data Exchange (ETDEWEB)

    Caravaggio, G.

    2002-07-01

    This study examined the electrochemical properties of layered double hydroxides (LDH) in half-cells to determine if they can be used in nickel-cadmium (Ni-Cd) and nickel-metal hydride (NiMH) batteries. The LDHs were prepared by coprecipitation and were characterized by X-ray diffraction analysis. The nickel-aluminium LDHs were found to be the most stable during potassium hydroxide electrolyte discharge because the aluminium acted in a two fold manner. The high charge to radius ratio increased the electrostatic interaction between the anions and the metal layers. The acidity of the hydroxyl groups was due to the high exchange of electrons. The powders had lower discharge capacity compared to commercial electrode materials because of their low density. The nickel-vanadium LDHs exchanged only up to 1.2 electrons and were stable only up to a maximum of 14 days in electrolytic solutions of the cells. Zinc-aluminium LDHs were also synthesized and intercalated with phenyl phosphonic acid or 1,4-phenylene bis phosphonic acid to create microporous materials. X-ray diffraction, infra-red spectroscopy and nuclear magnetic resonance was used to characterize the compounds and determine crystallographic spacing. Grafting of both phosphonates to the metal layers had occurred and both materials showed little or no microporosity.

  15. Graphene-Based Materials for Biosensors: A Review

    Science.gov (United States)

    Suvarnaphaet, Phitsini; Pechprasarn, Suejit

    2017-01-01

    The advantages conferred by the physical, optical and electrochemical properties of graphene-based nanomaterials have contributed to the current variety of ultrasensitive and selective biosensor devices. In this review, we present the points of view on the intrinsic properties of graphene and its surface engineering concerned with the transduction mechanisms in biosensing applications. We explain practical synthesis techniques along with prospective properties of the graphene-based materials, which include the pristine graphene and functionalized graphene (i.e., graphene oxide (GO), reduced graphene oxide (RGO) and graphene quantum dot (GQD). The biosensing mechanisms based on the utilization of the charge interactions with biomolecules and/or nanoparticle interactions and sensing platforms are also discussed, and the importance of surface functionalization in recent up-to-date biosensors for biological and medical applications. PMID:28934118

  16. Graphene-Based Materials for Biosensors: A Review

    Directory of Open Access Journals (Sweden)

    Phitsini Suvarnaphaet

    2017-09-01

    Full Text Available The advantages conferred by the physical, optical and electrochemical properties of graphene-based nanomaterials have contributed to the current variety of ultrasensitive and selective biosensor devices. In this review, we present the points of view on the intrinsic properties of graphene and its surface engineering concerned with the transduction mechanisms in biosensing applications. We explain practical synthesis techniques along with prospective properties of the graphene-based materials, which include the pristine graphene and functionalized graphene (i.e., graphene oxide (GO, reduced graphene oxide (RGO and graphene quantum dot (GQD. The biosensing mechanisms based on the utilization of the charge interactions with biomolecules and/or nanoparticle interactions and sensing platforms are also discussed, and the importance of surface functionalization in recent up-to-date biosensors for biological and medical applications.

  17. Anion exchange composite membrane based on octa quaternary ammonium Polyhedral Oligomeric Silsesquioxane for alkaline fuel cells

    Science.gov (United States)

    Elumalai, Vijayakumar; Sangeetha, Dharmalingam

    2018-01-01

    A series of novel composite anion exchange membranes were prepared via simple solution casting method using synthesized quaternary ammonium functionalized Polyhedral Oligomeric Silsesquioxane (QA-POSS) with Quaternary polysulfone (QPSU). QA-POSS was synthesized from prepared Cl-POSS and well characterized by FT-IR, NMR, SEM and TEM analyses to confirm the chemical modifications and cubic morphologies. The QA-POSS nano particles have dual role in the membrane providing additional ion conducting groups and reinforcing the membrane in molecular level for the overall improvement of composite membrane. Additionally, the composite membranes were characterized by XRD, SEM, Ion exchange capacity (IEC), water uptake and conductivity to ensure the suitability of its use as an electrolyte in alkaline fuel cell. Finally, membrane electrode assembly (MEA) was fabricated using Pt anode (0.25 mg/cm2), Ag cathode (0.375 mg/cm2) and various synthesized composite membranes, and then it was tested in real time fuel cell setup. The membrane with 15% QA-POSS showed the maximum power density of 321 mW/cm2. The results showed that QA-POSS possess the ability to enhance the performance of the anion exchange membrane significantly.

  18. Evaluating the Effects of Metals on Microorganisms in Flooded Paddy Soils Using the SEM/AVS-Based Approach and Measurements of Exchangeable Metal Concentrations.

    Science.gov (United States)

    Kunito, Takashi; Toya, Hitomi; Sumi, Hirotaka; Ishikawa, Yuichi; Toda, Hideshige; Nagaoka, Kazunari; Saeki, Kazutoshi; Aikawa, Yoshio; Matsumoto, Satoshi

    2017-04-01

    We examined possible adverse effects of heavy metals on microbial activity, biomass, and community composition using the simultaneously extracted metals (SEM)/acid-volatile sulfide (AVS)-based approach and measurements of exchangeable metal concentrations in three paddy soils (wastewater-contaminated soil, mine-contaminated soil, and noncontaminated soil) incubated for 60 days under flooded conditions. Incubation under flooding increased pH and decreased Eh in all samples. AVS increased when Eh decreased to approximately -200 mV for the mine-contaminated and noncontaminated soils, while the wastewater-contaminated soil originally had a high concentration of AVS despite its air-dried condition. Addition of rice straw or alkaline material containing calcium carbonate and gypsum increased AVS levels under flooded conditions. We observed no apparent relationship between soil enzyme activity (β-D-glucosidase and acid phosphatase) and concentrations of SEM, [∑SEM - AVS], and exchangeable metals. Bacterial and fungal community composition, assessed using polymerase chain reaction-denaturing gradient gel electrophoresis (DGGE) analysis targeting rRNA genes, was largely influenced by site of collection and incubation time, but metal contamination did not influence community composition. We observed significant negative correlations between biomass C and [∑SEM - AVS] and between biomass C and ∑SEM, suggesting that [∑SEM - AVS] and ∑SEM might reflect the bioavailability of organic matter to microorganisms in these soils.

  19. Factors affecting the bond strength of denture base and reline acrylic resins to base metal materials

    Directory of Open Access Journals (Sweden)

    Naomi Tanoue

    2013-07-01

    Full Text Available OBJECTIVE: The shear bond strengths of two hard chairside reline resin materials and an auto-polymerizing denture base resin material to cast Ti and a Co-Cr alloy treated using four conditioning methods were investigated. MATERIAL AND METHODS: Disk specimens (diameter 10 mm and thickness 2.5 mm were cast from pure Ti and Co-Cr alloy. The specimens were wet-ground to a final surface finish of 600 grit, air-dried, and treated with the following bonding systems: 1 air-abraded with 50-70-µm grain alumina (CON; 2 1 + conditioned with a primer, including an acidic phosphonoacetate monomer (MHPA; 3 1 + conditioned with a primer including a diphosphate monomer (MDP; 4 treated with a tribochemical system. Three resin materials were applied to each metal specimen. Shear bond strengths were determined before and after 10,000 thermocycles. RESULTS: The strengths decreased after thermocycling for all combinations. Among the resin materials assessed, the denture base material showed significantly (p<0.05 greater shear bond strengths than the two reline materials, except for the CON condition. After 10,000 thermocycles, the bond strengths of two reline materials decreased to less than 10 MPa for both metals. The bond strengths of the denture base material with MDP were sufficient: 34.56 MPa for cast Ti and 38.30 for Co-Cr alloy. CONCLUSION: Bonding of reline resin materials to metals assessed was clinically insufficient, regardless of metal type, surface treatment, and resin composition. For the relining of metal denture frameworks, a denture base material should be used.

  20. New absorbent material acoustic based on kenaf’s fibre

    Directory of Open Access Journals (Sweden)

    Ramis, J.

    2010-09-01

    Full Text Available Acoustic Standards in the building are responsible for, companies and individuals, propose new acoustic materials for the sound isolation. This paper presents a new sound-absorbent material, it is based on natural fibres, particularly fibres of kenaf. It also proposes an empirical model for this material, this models depends on the frequency. There are accepted models from the scientific community about mineral wool, glass wool, rock wool, foam or polyester fibre. Several of these models are empirical. They are obtained from the equation adjustments about the acoustic impedance and propagation constant behaviour, depending upon the flow resistivity, fibre’s diameter and density. There are even standards like UNE-EN 12354-6 where these models are accepted under certain limitations like the fundamental basis as in the materials’ acoustics behaviour prediction. From the various tests conducted in the laboratory, empirical equations are proposed for this new acoustic material. In addition, there has been a first approach to validate this model in combination with a micro-structural model, based on the steps taken by Bies-Hansen (1, which allows us to obtain the value of the resistance to flow.

    El carácter marcadamente prestacional de las normativas acústicas en la edificación abre el camino a la propuesta, por parte de empresas y particulares, de nuevos materiales acústicos susceptibles de ser utilizados en el ámbito de la acústica de la edificación. Éste es el caso que nos ocupa en el presente trabajo en el que se presenta un nuevo material acústico absorbente basado en fibras vegetales, concretamente el kenaf. Además se propone un modelo empírico de modelización del comportamiento absorbente de varias composiciones de este material en función de la frecuencia. Existen modelos de diferentes lanas minerales, lanas de roca, lanas de vidrio, espumas o lanas de poliéster. Algunos de estos modelos —llamados empíricos— se