Nanomaterials-Enhanced Electrically Switched Ion Exchange Process for Water Treatment

International Nuclear Information System (INIS)

Lin, Yuehe; Choi, Daiwon; Wang, Jun; Bontha, Jagannadha R.

2009-01-01

The objective of our work is to develop an electrically switched ion exchange (ESIX) system based on conducting polymer/carbon nanotube (CNT) nanocomposites as a new and cost-effective approach for removal of radioactive cesium, chromate, and perchlorate from contaminated groundwater. The ESIX technology combines ion exchange and electrochemistry to provide a selective, reversible method for the removal of target species from wastewater. In this technique, an electroactive ion exchange layer is deposited on a conducting substrate, and ion uptake and elution are controlled directly by modulation of the potential of the layer. ESIX offers the advantages of highly-efficient use of electrical energy combined with no secondary waste generation. Recently, we have improved upon the ESIX process by modifying the conducting substrate with carbon nanotubes prior to the deposition of the electroactive ion exchanger. The nanomaterial-based electroactive ion exchange technology will remove cesium-137, chromate, and perchlorate rapidly from wastewater. The high porosity and high surface area of the electroactive ion exchange nanocomposites results in high loading capacity and minimize interferences for non-target species. Since the ion adsorption/desorption is controlled electrically without generating a secondary waste, this electrically active ion exchange process is a green process technology that will greatly reduce operating costs

Recent developments on ion-exchange membranes and electro-membrane processes.

Science.gov (United States)

Nagarale, R K; Gohil, G S; Shahi, Vinod K

2006-02-28

Rapid growth of chemical and biotechnology in diversified areas fuels the demand for the need of reliable green technologies for the down stream processes, which include separation, purification and isolation of the molecules. Ion-exchange membrane technologies are non-hazardous in nature and being widely used not only for separation and purification but their application also extended towards energy conversion devices, storage batteries and sensors etc. Now there is a quite demand for the ion-exchange membrane with better selectivities, less electrical resistance, high chemical, mechanical and thermal stability as well as good durability. A lot of work has been done for the development of these types of ion-exchange membranes during the past twenty-five years. Herein we have reviewed the preparation of various types of ion-exchange membranes, their characterization and applications for different electro-membrane processes. Primary attention has been given to the chemical route used for the membrane preparation. Several general reactions used for the preparation of ion-exchange membranes were described. Methodologies used for the characterization of these membranes and their applications were also reviewed for the benefit of readers, so that they can get all information about the ion-exchange membranes at one platform. Although there are large number of reports available regarding preparations and applications of ion-exchange membranes more emphasis were predicted for the usefulness of these membranes or processes for solving certain type of industrial or social problems. More efforts are needed to bring many products or processes to pilot scale and extent their applications.

Isotope exchange process and device

International Nuclear Information System (INIS)

Delvalle, Pierre.

1974-01-01

A process for enriching uranium in one of its isotopes is described. To do so, cascade isotopic exchanges are made by contact between U(III) and U(IV) in conditions avoiding the oxidation of U(III) in U(IV). A liquid phase containing an uranium compound and free of other group III to VIII metals of the periodic classification, in which uranium is present at a first valence is placed in contact with a second valence uranium compound, protected from any contact with a conducting solid and with an agent bringing free or release oxygen. The second phase is organic. The process includes a counter current isotopic exchange between an aqueous phase containing a U +4 salting-out agent and the uranium as U +3 ions and an organic phase containing the uranium at valence IV. This is followed by the extraction of U(IV) from the organic phase into the previously spent aqueous phase and the reduction of uranium from valence IV to valence III; finally by oxidation of U(III) of the aqueous phase into U(IV) and the transfer of U(IV) into the previously exhausted organic phase [fr

Ligands Exchange Process on Gold Nanoparticles in Acetone Solution

Science.gov (United States)

Hu, C. L.; Mu, Y. Y.; Bian, Z. C.; Luo, Z. H.; Luo, K.; Huang, A. Z.

2018-05-01

The ligands exchange process on gold nanoparticles (GNPs) was proceeded by using hydrophobic group (PPh3) and hydrophilic group (THPO) in acetone solution. The FTIR and XPS results demonstrated that part of THPO was replaced by PPh3 which was dissolved in polar solution (acetone); the results were in accordance with the electrochemical analysis where the differential capacity decreased with increasing exchange time. After 12 h, the exchange process terminated and the final ratio of PPh3 and THPO was about 1.4: 1. This ratio remained unchanged although the PPh3 and THPO modified GNPs re-dispersed in the PPh3 acetone solution demonstrating the stable adsorption of both ligands after exchanging for 12 h. The TEM images showed that the gold nanoparticles were self-assembled from scattered to arranged morphology due to the existence of hydrophilic and hydrophobic ligands and led to Janus gold nanoparticles.

High temperature heat exchange: nuclear process heat applications

International Nuclear Information System (INIS)

Vrable, D.L.

1980-09-01

The unique element of the HTGR system is the high-temperature operation and the need for heat exchanger equipment to transfer nuclear heat from the reactor to the process application. This paper discusses the potential applications of the HTGR in both synthetic fuel production and nuclear steel making and presents the design considerations for the high-temperature heat exchanger equipment

THE USE OF EXCHANGEABLE BONDS DURING THE PRIVATIZATION PROCESS

Directory of Open Access Journals (Sweden)

Damian Kaźmierczak

2014-04-01

Full Text Available In our article we present the use of hybrid securities in the privatization process. We show that exchangeable bonds may be successfully applied during privatization of state companies throughout the world. It may be profitable for many reasons. Firstly, the exchangeables offer a much lower coupon in comparison with the ordinary government bonds which may be crucial for highly indebted countries. Secondly, throughout the entire maturity period the state remains the owner of the privatized firm which means that the government can be a beneficiary of high dividends paid by the public enterprises and can actively manage them. Thirdly, in the case of unfavorable market conditions the authorities get an opportunity to wait for the end of economic turmoil in order to avoid selling the equity participations under their true value. Finally, the issue of certain types of exchangeables (e.g. callable exchangeables or mandatory exchangeables and adding several provisions (e.g. greenshoe option or clean-up call makes the instrument more flexible for the issuer. We also present a few examples of the privatization processes by means of exchangeable bonds i.a. in Germany and in Austria. Most of such operations, e.g. German Deutsche Post, Austrian Telekom Austria or Portuguese Galp Energia SGPS S.A. were completed with success.

Evaluation methodology for advance heat exchanger concepts using analytical hierarchy process

International Nuclear Information System (INIS)

Sabharwall, Piyush; Kim, Eung Soo; Patterson, Mike

2012-01-01

This study describes how the major alternatives and criteria being developed for the heat exchangers for next generation nuclear reactors are evaluated using the analytical hierarchy process (AHP). This evaluation was conducted as an aid in developing and selecting heat exchangers for integrating power production and process heat applications with next generation nuclear reactors. The basic setup for selecting the most appropriate heat exchanger option was established with evaluation goals, alternatives, and criteria. The two potential candidates explored in this study were shell-and-tube (helical coiled) and printed circuit heat exchangers. Based on study results, the shell-and-tube (helical coiled) heat exchanger is recommended for a demonstration reactor in the near term, mainly because of its reliability.

Designing heat exchangers for process heat reactors

International Nuclear Information System (INIS)

Quade, R.N.

1980-01-01

A brief account is given of the IAEA specialist meeting on process heat applications technology held in Julich, November 1979. The main emphasis was on high temperature heat exchange. Papers were presented covering design requirements, design construction and prefabrication testing, and selected problems. Primary discussion centered around mechanical design, materials requirements, and structural analysis methods and limits. It appears that high temperature heat exchanges design to nuclear standards, is under extensive development but will require a lengthy concerted effort before becoming a commercial reality. (author)

Inorganic ion exchangers. Application to liquid effluent processing

International Nuclear Information System (INIS)

Dozol, M.

1983-10-01

Main inorganic ion exchangers used for radioactive liquid effluents presented in this report are: synthetic and natural zeolites, in titanium oxides, titanates, niobates, tantalates, zirconates, some insoluble salts of zirconium, molybdenum and tin, heteropolyacids and polyantimonic acid. Properties of these ion exchangers are described: structure, adsoption, radiation effects and thermal stability, application to waste processing, radioactive waste storage uranium and cesium 137 recovery are evoked [fr

Developing maintenance technologies for FBR's heat exchanger units by advanced laser processing

International Nuclear Information System (INIS)

Nishimura, Akihiko; Shimada, Yukihiro

2011-01-01

Laser processing technologies were developed for the purpose of maintenance of FBR's heat exchanger units. Ultrashort laser processing fabricated fiber Bragg grating sensor for seismic monitoring. Fiber laser welding with a newly developed robot system repair cracks on inner wall of heat exchanger tubes. Safety operation of the heat exchanger units will be improved by the advanced laser processing technologies. These technologies are expected to be applied to the maintenance for the next generation FBRs. (author)

Charge exchange processes of high energy heavy ions channeled in crystals

International Nuclear Information System (INIS)

Andriamonje, S.; Dural, J.; Toulemonde, M.; Groeneveld, K.O.; Maier, R.; Quere, Y.

1990-01-01

The interaction of moving ions with single crystals is very sensitive to the orientation of the incident beam with respect to the crystalline directions of the target. The experiments show that high energy heavy ion channeling deeply modifies the slowing down and charge exchange processes. In this review, we describe the opportunity offered by channeling conditions to study the charge exchange processes. Some aspects of the charge exchange processes with high energy channeled heavy ions are selected from the extensive literature published over the past few years on this subject. Special attention is given to the work performed at the GANIL facility on the study of Radiative Electron Capture (REG), Electron Impact Ionisation (EII), and convoy electron emission. Finally we emphasize the interest of studying resonant charge exchange processes such as Resonant Coherent Excitation (RCE), Resonant Transfer and Excitation (RTE) or Dielectronic Recombination (DR) and the recently proposed Nuclear Excitation by Electron Capture (NEEC)

Hydrogen-water isotopic exchange process

International Nuclear Information System (INIS)

Cheung, H.

1984-01-01

The objects of this invention are achieved by a dual temperature isotopic exchange process employing hydrogen-water exchange with water passing in a closed recirculation loop between a catalyst-containing cold tower and the upper portion of a catalyst-containing hot tower, with feed water being introduced to the lower portion of the hot tower and being maintained out of contact with the water recirculating in the closed loop. Undue retarding of catalyst activity during deuterium concentration can thus be avoided. The cold tower and the upper portion of the hot tower can be operated with relatively expensive catalyst material of higher catalyst activity, while the lower portion of the hot tower can be operated with a relatively less expensive, more rugged catalyst material of lesser catalyst activity. The feed water stream, being restricted solely to the lower portion of the hot tower, requires minimal pretreatment for the removal of potential catalyst contaminants. The catalyst materials are desirably coated with a hydrophobic treating material so as to be substantially inaccessible to liquid water, thereby retarding catalyst fouling while being accessible to the gas for enhancing isotopic exchange between hydrogen gas and water vapor. A portion of the water of the closed loop can be passed to a humidification zone to heat and humidify the circulating hydrogen gas and then returned to the closed loop

Transport and mass exchange processes in sand and gravel aquifers (v.1)

International Nuclear Information System (INIS)

Moltyaner, G.

1990-01-01

The objectives of this conference were to exchange information on promising field measurement techniques used for the characterization of spatial variability of geologic formations and on new methods used for quantifying the effect of spatial variability on groundwater flow and transport of materials; to discuss novel developments in the theory of transport processes and simulation methods; and to present views and opinions on future initiatives and directions in the design of large-scale field tracer experiments and the development of conceptual and mathematical models of transport and mass exchange processes. The 46 papers presented in these proceedings are divided into six sections: field studies of transport processes; groundwater tracers and novel field measurement techniques; promising methods and field measurement techniques for quantifying the effect of geological heterogeneities on groundwater flow and transport; novel developments in the theory of transport processes; numerical modelling of transport and mass exchange processes; and field and modelling studies of mass exchange processes. (L.L.)

Cation exchange process for molten salt extraction residues

International Nuclear Information System (INIS)

Proctor, S.G.

1975-01-01

A new method, utilizing a cation exchange technique, has been developed for processing molten salt extraction (MSE) chloride salt residues. The developed ion exchange procedure has been used to separate americium and plutonium from gross quantities of magnesium, potassium, and sodium chloride that are present in the residues. The recovered plutonium and americium contained only 20 percent of the original amounts of magnesium, potassium, and sodium and were completely free of any detectable amounts of chloride impurity. (U.S.)

The Role of Exchange Traded Funds in the Price Discovery Process of Stocks Listed on the Botswana Stock Exchange

Directory of Open Access Journals (Sweden)

Edson Kambeu

2017-04-01

Full Text Available In this paper we analyse the role of Exchange Traded Funds (ETFs in the price discovery process of stocks listed at the Botswana Stock Exchange.Using daily returns data covering the period 3 January 2013 to 31 December 2015   for Beta Betta ETF and Domestic Company Indices, we utilize a VECM model to find out whether the Betta Beta ETF is playing a significant role in the price discovery process of stocks listed on the Botswana Stock Exchange. We found the error correction term to be statistically significant thereby confirming that the Beta Betta ETF is playing a significant role in the price discovery of stocks listed on the Botswana Stock Exchange.

Charge-exchange processes in a divertor plasma with account for excited particles

International Nuclear Information System (INIS)

Krasheninnikov, S.I.; Lisitsa, V.S.; Pigarov, A.Yu.

1988-01-01

A model describing dynamics of neutral atoms and multicharge ions in tokamak plasma, taking account of cascade excitation effect on charge exchange and ionization processes, is constructed. Dependences of effective rate of processes of proton charge exchange on hydrogen atom and non-resonance helium atom charge exchange on proton and α-particle- on atomic hydrogen on tokamak divertor plasma parameters are calculated. It is shown that H + +He→H-He + charge exchange can make up a notable shave (∼30%) in full helium ionization rate. Accounting for Ge 2+ charge exchange on atomic hydrogen under INTOR reactor divertor plasma conditions can lead to substantial He 2+ →He + conversion and thus increase diverter plate sputtering by helium ions

Air/surface exchange processes of mercury and their linkage to atmospheric pools

International Nuclear Information System (INIS)

Bahlmann, Enno; Ebinghaus, Ralf

2001-01-01

The atmospheric mercury cycle is strongly linked to the terrestrial, aquatic and biologic cycle of mercury via air/surface exchange processes. In order to quantify mercury fluxes from and to the atmosphere to predict local and regional source contributions the methods for flux measurements as well as the physicochemical factors controlling air/surface exchange processes must be assessed. We will describe methods for the determination of mercury and mercury species in ambient air which are basic for investigation of air/surface exchange processes. Further on we will describe approaches for studying the physicochemical factors controlling this processes by using a new laboratory flux measurement system. (author)

Application of ion exchange processes for the treatment of radioactive waste and management of spent ion exchangers

International Nuclear Information System (INIS)

2002-01-01

This report describes the ion exchange technologies currently used and under development in nuclear industry, in particular for waste management practices, along with the experience gained in their application and with the subsequent handling, treatment and conditioning of spent ion exchange media for long term storage and/or disposal. The increased role of inorganic ion exchangers for treatment of radioactive liquid waste, both in nuclear power plant operations and in the fuel reprocessing sector, is recognised in this report. The intention of this report is to consolidate the previous publications, document recent developments and describe the state of the art in the application of ion exchange processes for the treatment of radioactive liquid waste and the management of spent ion exchange materials

Performance characterization of hydrogen isotope exchange and recombination catalysts for tritium processing

International Nuclear Information System (INIS)

Suppiah, S.; Ryland, D.; Marcinkowska, K.; Boniface, H.; Everatt, A.

2010-01-01

AECL's hydrogen isotope exchange catalyst and recombination catalysts have been successfully applied to a wide range of industrial tritium-removal applications. The catalysts are used for Liquid Phase Catalytic Exchange (LPCE) and for gas-phase and trickle-bed recombination of hydrogen isotopes and have led to process simplification, improved safety and operational advantages. Catalyst performance design equations derived from laboratory testing of these catalysts have been validated against performance under industrial conditions. In a Combined Electrolysis and Catalytic Exchange (CECE) demonstration plant analyses of LPCE and recombiner efficiency were carried out as a function of catalyst activity over a wide range of operation. A steady-state process simulation used to model and design the hydrogen-water isotopic exchange processes, such as the CECE detritiation plant, was validated using the results of this demonstration. Catalyst development for isotope-exchange and recombination applications has continued over the last decade. As a result, significant improvements in catalyst performance have been achieved for these applications. This paper outlines the uniqueness of AECL's specialized catalysts and process designs for these applications with examples from laboratory and industrial case studies.

Enrichment of 15N and 10B isotopes by chemical exchange process

International Nuclear Information System (INIS)

D'Souza, A.B.; Sonwalkar, A.S.; Subrahmanyam, B.V.; Valladares, B.A.

1994-01-01

Many processes are available for separation of stable isotopes like distillation, chemical exchange, thermal diffusion, gaseous diffusion, centrifuge etc. Chemical exchange process is eminently suitable for separation of isotopes of light elements. Work done on separation and enrichment of two of the stable isotopes viz. 15 N and 10 B in Chemical Engineering Division is presented. 15 N is widely used as a tracer in agricultural research and 10 B is used in nuclear industry as control rod material, soluble reactor poison, neutron detector etc. The work on 15 N isotope resulted in a pilot plant, which was the only source of this material in the country for many years and later it was translated into a production plant as M/s. RCF Ltd. The work done on the ion-exchange process for enrichment of 10 B isotope which is basically a chemical exchange process, is now being updated into a pilot plant to produce enriched 10 B to be used as soluble reactor poison. (author)

Development of wet-proofed catalyst and catalytic exchange process for tritium extraction

Energy Technology Data Exchange (ETDEWEB)

Song, Myung Jae; Son, Soon Hwan; Chung, Yang Gun; Lee, Gab Bock [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center

1996-12-31

To apply a liquid phase catalytic exchange(LPCE) process for the tritium extraction from tritiated heavy water, the wet proofed catalyst to allow the hydrogen isotopic exchange reaction between liquid water and hydrogen gas was developed. A styrene divinyl benzene copolymer was selected as am effective catalyst support and prepared by suspension copolymerization. After post-treatment, final catalyst supports were dipped in chloroplatinic acid solution. The catalyst support had a good physical properties at a particular preparation condition. The catalytic performance was successfully verified through hydrogen isotopic exchange reaction in the exchange column. A mathematical model for the tritium removal process consisted of LPCE front-ended process and cryogenic distillation process was established using the NTU-HTU method for LPCE column and the FUG method for cryogenic distillation column, respectively. A computer program was developed using the model and then used to investigate optimum design variables which affect the size of columns and tritium inventory (author). 84 refs., 113 figs.

Efficient separations and processing crosscutting program 1996 technical exchange meeting. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

This document contains summaries of technology development presented at the 1996 Efficient Separations and Processing Crosscutting Program Technical Exchange Meeting. This meeting is held annually to promote a free exchange of ideas among technology developers, potential users and other interested parties within the EM community. During this meeting the following many separation processes technologies were discussed such as ion exchange, membrane separation, vacuum distillation, selective sorption, and solvent extraction. Other topics discussed include: waste forms; testing or inorganic sorbents for radionuclide and heavy metal removal; selective crystallization; and electrochemical treatment of liquid wastes. This is the leading abstract, individual papers have been indexed separately for the databases.

Efficient separations and processing crosscutting program 1996 technical exchange meeting. Proceedings

International Nuclear Information System (INIS)

1996-01-01

This document contains summaries of technology development presented at the 1996 Efficient Separations and Processing Crosscutting Program Technical Exchange Meeting. This meeting is held annually to promote a free exchange of ideas among technology developers, potential users and other interested parties within the EM community. During this meeting the following many separation processes technologies were discussed such as ion exchange, membrane separation, vacuum distillation, selective sorption, and solvent extraction. Other topics discussed include: waste forms; testing or inorganic sorbents for radionuclide and heavy metal removal; selective crystallization; and electrochemical treatment of liquid wastes. This is the leading abstract, individual papers have been indexed separately for the databases

Operation and control of ion-exchange processes for treatment of radioactive wastes

International Nuclear Information System (INIS)

Emelity, L.A.

1967-01-01

A manual dealing with the application of ion-exchange materials to the treatment of radioactive wastes and reviewing the facilities currently using this method. This book is one of three commissioned by the IAEA on the principal methods of concentrating radioactive wastes. The content of this document is: (i) Historical review related to removal of radioactivity; (ii) Principles of ion exchange (iii) Ion-exchange materials; (iv) Limitations of ion exchangers; (v) Application of ion exchange to waste processing; (vi) Operational procedures and experiences; (vii) Cost-of-treatment by ion-exchange. The document also gives a list of producers of ion-exchange material and defines some relevant terms. 101 refs, 31 figs, 27 tabs

Operation and control of ion-exchange processes for treatment of radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Emelity, L A [Los Alamos National Lab., NM (United States)

1967-12-01

A manual dealing with the application of ion-exchange materials to the treatment of radioactive wastes and reviewing the facilities currently using this method. This book is one of three commissioned by the IAEA on the principal methods of concentrating radioactive wastes. The content of this document is: (i) Historical review related to removal of radioactivity; (ii) Principles of ion exchange (iii) Ion-exchange materials; (iv) Limitations of ion exchangers; (v) Application of ion exchange to waste processing; (vi) Operational procedures and experiences; (vii) Cost-of-treatment by ion-exchange. The document also gives a list of producers of ion-exchange material and defines some relevant terms. 101 refs, 31 figs, 27 tabs.

Rapid and accurate processing method for amide proton exchange rate measurement in proteins

International Nuclear Information System (INIS)

Koskela, Harri; Heikkinen, Outi; Kilpelaeinen, Ilkka; Heikkinen, Sami

2007-01-01

Exchange between protein backbone amide hydrogen and water gives relevant information about solvent accessibility and protein secondary structure stability. NMR spectroscopy provides a convenient tool to study these dynamic processes with saturation transfer experiments. Processing of this type of NMR spectra has traditionally required peak integration followed by exponential fitting, which can be tedious with large data sets. We propose here a computer-aided method that applies inverse Laplace transform in the exchange rate measurement. With this approach, the determination of exchange rates can be automated, and reliable results can be acquired rapidly without a need for manual processing

Ultrafast spin exchange-coupling torque via photo-excited charge-transfer processes

Science.gov (United States)

Ma, X.; Fang, F.; Li, Q.; Zhu, J.; Yang, Y.; Wu, Y. Z.; Zhao, H. B.; Lüpke, G.

2015-10-01

Optical control of spin is of central importance in the research of ultrafast spintronic devices utilizing spin dynamics at short time scales. Recently developed optical approaches such as ultrafast demagnetization, spin-transfer and spin-orbit torques open new pathways to manipulate spin through its interaction with photon, orbit, charge or phonon. However, these processes are limited by either the long thermal recovery time or the low-temperature requirement. Here we experimentally demonstrate ultrafast coherent spin precession via optical charge-transfer processes in the exchange-coupled Fe/CoO system at room temperature. The efficiency of spin precession excitation is significantly higher and the recovery time of the exchange-coupling torque is much shorter than for the demagnetization procedure, which is desirable for fast switching. The exchange coupling is a key issue in spin valves and tunnelling junctions, and hence our findings will help promote the development of exchange-coupled device concepts for ultrafast coherent spin manipulation.

Process for exchanging tritium between gaseous hydrogen and water

International Nuclear Information System (INIS)

Hindin, S.G.; Roberts, G.W.

1981-01-01

An improved method of exchanging and concentrating the radioactive isotope of hydrogen from water or hydrogen gas is described. This heavy water enrichment system involves a low pressure, dual temperature process. (U.K.)

Spin-locking vs. chemical exchange saturation transfer MRI for investigating chemical exchange process between water and labile metabolite protons

Science.gov (United States)

Jin, Tao; Autio, Joonas; Obata, Takayuki; Kim, Seong-Gi

2010-01-01

Chemical exchange saturation transfer (CEST) and spin-locking (SL) experiments were both able to probe the exchange process between protons of non-equivalent chemical environments. To compare the characteristics of the CEST and SL approaches in the study of chemical exchange effects, we performed CEST and SL experiments at varied pH and concentrated metabolites with exchangeable amide, amine, and hydroxyl protons at 9.4 T. Our results show that: i) On-resonance SL is most sensitive to chemical exchanges in the intermediate exchange regime and is able to detect hydroxyl and amine protons on a millimolar concentration scale. Off-resonance SL and CEST approaches are sensitive to slow-exchanging protons when an optimal SL or saturation pulse power matches the exchanging rate, respectively. ii) Offset frequency-dependent SL and CEST spectra are very similar, and can be explained well with an SL model recently developed by Trott and Palmer. iii) The exchange rate and population of metabolite protons can be determined from offset-dependent SL or CEST spectra or from on-resonance SL relaxation dispersion measurements. iv) The asymmetry of the magnetization transfer ratio (MTRasym) is highly dependent on the choice of saturation pulse power. In the intermediate exchange regime, MTRasym becomes complicated and should be interpreted with care. PMID:21500270

Finite-Time Approach to Microeconomic and Information Exchange Processes

Directory of Open Access Journals (Sweden)

Serghey A. Amelkin

2009-07-01

Full Text Available Finite-time approach allows one to optimize regimes of processes in macrosystems when duration of the processes is restricted. Driving force of the processes is difference of intensive variables: temperatures in thermodynamics, values in economics, etc. In microeconomic systems two counterflow fluxes appear due to the only driving force. They are goods and money fluxes. Another possible case is two fluxes with the same direction. The processes of information exchange can be described by this formalism.

Mark-18A Ion Exchange Raffinate Management Strategy & Processing Recommendations

Energy Technology Data Exchange (ETDEWEB)

Smith, T. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-06-21

It is desired to recover Cm-244 through Cm-248 from dissolved Mark-18A targets following anion exchange processing to remove the Pu. The Cm will be sent to Oak Ridge National Laboratory (ORNL) for additional R&D. Approximately 5-8 L per quarter of a Mark-18A target will have undergone anion exchange treatment and will contain Cm. A significant portion of this volume of anion exchange raffinate solution is dissolved fission products not desired to be recovered which could be sent to waste. To reduce the amount of material being sent to ORNL, a waste and volume minimization strategy was developed and is described in this report.

Transversity Amplitudes in Hypercharge Exchange Processes

International Nuclear Information System (INIS)

Aguilar Benitez de Lugo, M.

1979-01-01

' In this work we present several techniques developed for the extraction of the. Transversity amplitudes governing quasi two-body meson baryon reactions with hypercharge exchange. We review the methods used in processes having a pure spin configuration, as well as the more relevant results obtained with data from K p and Tp interactions at intermediate energies. The predictions of the additive quark model and the ones following from exchange degeneracy and etoxicity are discussed. We present a formalism for amplitude analysis developed for reactions with mixed spin configurations and discuss the methods of parametric estimation of the moduli and phases of the amplitudes, as well as the various tests employed to check the goodness of the fits. The calculation of the generalized joint density matrices is given and we propose a method based on the generalization of the idea of multipole moments, which allows to investigate the structure of the decay angular correlations and establishes the quality of the fits and the validity of the simplifying assumptions currently used in this type of studies. (Author) 43 refs

Spin-locking versus chemical exchange saturation transfer MRI for investigating chemical exchange process between water and labile metabolite protons.

Science.gov (United States)

Jin, Tao; Autio, Joonas; Obata, Takayuki; Kim, Seong-Gi

2011-05-01

Chemical exchange saturation transfer (CEST) and spin-locking (SL) experiments were both able to probe the exchange process between protons of nonequivalent chemical environments. To compare the characteristics of the CEST and SL approaches in the study of chemical exchange effects, we performed CEST and SL experiments at varied pH and concentrated metabolite phantoms with exchangeable amide, amine, and hydroxyl protons at 9.4 T. Our results show that: (i) on-resonance SL is most sensitive to chemical exchanges in the intermediate-exchange regime and is able to detect hydroxyl and amine protons on a millimolar concentration scale. Off-resonance SL and CEST approaches are sensitive to slow-exchanging protons when an optimal SL or saturation pulse power matches the exchanging rate, respectively. (ii) Offset frequency-dependent SL and CEST spectra are very similar and can be explained well with an SL model recently developed by Trott and Palmer (J Magn Reson 2002;154:157-160). (iii) The exchange rate and population of metabolite protons can be determined from offset-dependent SL or CEST spectra or from on-resonance SL relaxation dispersion measurements. (iv) The asymmetry of the magnetization transfer ratio (MTR(asym)) is highly dependent on the choice of saturation pulse power. In the intermediate-exchange regime, MTR(asym) becomes complicated and should be interpreted with care. Copyright © 2010 Wiley-Liss, Inc.

Charge exchange collisions in gases in the presence of competing processes

International Nuclear Information System (INIS)

Senba, Masayoshi; British Columbia Univ., Vancouver

1988-01-01

The slowing down of charged particles in noble gases has been investigated theoretically from the charge exchange regime down to thermal energy. A formalism has been developed which allows one to calculate the rate of energy loss, the collision rate, the slowing down time, the neutral fraction and other quantities of interest directly from the cross sections of the atomic process involved. The formalism has been applied to the case of muons in He where two experimental observables, the fraction of the neutral species (muonium) and the muon spin depolarisation during charge exchange, have been calculated. The calculations have reproduced experimental results very well. It has also been found that the elastic process at the end of the slowing down reduces the number of charge exchange collisions drastically, thus sensitively affecting the neutral fraction and the muon spin depolarisation. (author)

Intensification of Evaporation and Condensation Processes in Heat Exchange Apparatus

Directory of Open Access Journals (Sweden)

L. L. Vasiliev

2005-01-01

Full Text Available The paper describes proposed design solutions for an intensification of heat transfer in evaporation and condensation heat exchangers. Complex experimental research of heat and mass transfer processes in flat and round cross-section miniature heat pipes is carried out. Optimization, development, manufacturing and an experimental investigation of copper miniature heat pipes with sintered powder are executed. Investigation results of capillary-porous structure properties that are used in evaporation and condensation heat-exchange apparatus are presented.

Alert Exchange Process Protocol

Science.gov (United States)

Groen, Frank

2015-01-01

The National Aeronautics and Space Administration of the United States of America (NASA), and the European Space Agency (ESA), and the Japanese Aerospace Exploration Agency (JAXA), acknowledging that NASA, ESA and JAXA have a mutual interest in exchanging Alerts and Alert Status Lists to enhance the information base for each system participant while fortifying the general level of cooperation between the policy agreement subscribers, and each Party will exchange Alert listings on regular basis and detailed Alert information on a need to know basis to the extent permitted by law.

Progress Report for Diffusion Welding of the NGNP Process Application Heat Exchangers

Energy Technology Data Exchange (ETDEWEB)

R.E. Mizia; D.E. Clark; M.V. Glazoff; T.E. Lister; T.L. Trowbridge

2011-04-01

The NGNP Project is currently investigating the use of metallic, diffusion welded, compact heat exchangers to transfer heat from the primary (reactor side) heat transport system to the secondary heat transport system. The intermediate heat exchanger will transfer this heat to downstream applications such as hydrogen production, process heat, and electricity generation. The channeled plates that make up the heat transfer surfaces of the intermediate heat exchanger will have to be assembled into an array by diffusion welding.

The determinants of exchange rates and the movements of EUR/RON exchange rate via non-linear stochastic processes

Directory of Open Access Journals (Sweden)

Petrică Andreea-Cristina

2017-07-01

Full Text Available Modeling exchange rate volatility became an important topic for research debate starting with 1973, when many countries switched to floating exchange rate system. In this paper, we focus on the EUR/RON exchange rate both as an economic measure and present the implied economic links, and also as a financial investment and analyze its movements and fluctuations through two volatility stochastic processes: the Standard Generalized Autoregressive Conditionally Heteroscedastic Model (GARCH and the Exponential Generalized Autoregressive Conditionally Heteroscedastic Model (EGARCH. The objective of the conditional variance processes is to capture dependency in the return series of the EUR/RON exchange rate. On this account, analyzing exchange rates could be seen as the input for economic decisions regarding Romanian macroeconomics - the exchange rates being influenced by many factors such as: interest rates, inflation, trading relationships with other countries (imports and exports, or investments - portfolio optimization, risk management, asset pricing. Therefore, we talk about political stability and economic performance of a country that represents a link between the two types of inputs mentioned above and influences both the macroeconomics and the investments. Based on time-varying volatility, we examine implied volatility of daily returns of EUR/RON exchange rate using the standard GARCH model and the asymmetric EGARCH model, whose parameters are estimated through the maximum likelihood method and the error terms follow two distributions (Normal and Student’s t. The empirical results show EGARCH(2,1 with Asymmetric order 2 and Student’s t error terms distribution performs better than all the estimated standard GARCH models (GARCH(1,1, GARCH(1,2, GARCH(2,1 and GARCH(2,2. This conclusion is supported by the major advantage of the EGARCH model compared to the GARCH model which consists in allowing good and bad news having different impact on the

Charge exchange processes involving iron ions

International Nuclear Information System (INIS)

Phaneuf, R.A.

1985-01-01

A review and evaluation is given of the experimental data which are available for charge exchange processes involving iron ions and neutral H, H 2 and He. Appropriate scaling laws are presented, and their accuracy estimated for these systems. A bibliography is given of available data sources, as well as of useful data compilations and review articles. A procedure is recommended for providing single approximate formulae to the fusion community to describe total cross sections for electron capture by partially-stripped Fe/sup q+/ ions in collisions with H, H 2 and He, based on the scaling relationships suggested by Janev and Hvelplund

Recycle attuned catalytic exchange (RACE) for reliable and low inventory processing of highly tritiated water

International Nuclear Information System (INIS)

Iseli, M.; Schaub, M.; Ulrich, D.

1992-01-01

The detritiation of highly tritiated water by liquid phase catalytic exchange needs dilution of the feed with water to tritium concentrations suitable for catalyst and safety rules and to assure flow rates large enough for wetting the catalyst. Dilution by recycling detritiated water from within the exchange process has three advantages: the amount and concentration of the water for dilution is controlled within the exchange process, there is no additional water load to processes located downstream RACE, and the ratio of gas to liquid flow rates in the exchange column could be adjusted by using several recycles differing in amount and concentration to avoid an excessively large number of theoretical separation stages. In this paper, the flexibility of the recycle attuned catalytic exchange (RACE) and its effect on the cryogenic distillation are demonstrated for the detritiation of the highly tritiated water from a tritium breeding blanket

Statewide and Metropolitan Transportation Planning Processes : a TPCB Peer Exchange

Science.gov (United States)

2016-04-20

This report highlights key recommendations and noteworthy practices identified at Statewide and Metropolitan Transportation Planning Processes Peer Exchange held on September 9-10, 2015 in Shepherdstown, West Virginia. This event was sponsored ...

Exchange processes between a coniferous forest and the atmosphere

NARCIS (Netherlands)

Bosveld, F.C.

1999-01-01

This thesis deals with the research question: which processes are relevant in controlling the exchange fluxes between the forest and the atmosphere and how can this control be quantified? Answering this question is relevant for research in the fields of air pollution, weather and climate

Enrichment of {sup 15}N and {sup 10}B isotopes by chemical exchange process

Energy Technology Data Exchange (ETDEWEB)

D` Souza, A B; Sonwalkar, A S; Subrahmanyam, B V; Valladares, B A [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Many processes are available for separation of stable isotopes like distillation, chemical exchange, thermal diffusion, gaseous diffusion, centrifuge etc. Chemical exchange process is eminently suitable for separation of isotopes of light elements. Work done on separation and enrichment of two of the stable isotopes viz. {sup 15}N and {sup 10}B in Chemical Engineering Division is presented. {sup 15}N is widely used as a tracer in agricultural research and {sup 10}B is used in nuclear industry as control rod material, soluble reactor poison, neutron detector etc. The work on {sup 15}N isotope resulted in a pilot plant, which was the only source of this material in the country for many years and later it was translated into a production plant as M/s. RCF Ltd. The work done on the ion-exchange process for enrichment of {sup 10}B isotope which is basically a chemical exchange process, is now being updated into a pilot plant to produce enriched {sup 10}B to be used as soluble reactor poison. (author). 5 refs., 2 figs., 3 tabs.

Progress Report for Diffusion Welding of the NGNP Process Application Heat Exchangers

Energy Technology Data Exchange (ETDEWEB)

R.E. Mizia; D.E. Clark; M.V. Glazoff; T.E. Lister; T.L. Trowbridge

2011-12-01

The U.S. Department of Energy selected the high temperature gas-cooled reactor as the basis for the Next Generation Nuclear Plant (NGNP). The NGNP will demonstrate the use of nuclear power for electricity, hydrogen production, and process heat applications. The NGNP Project is currently investigating the use of metallic, diffusion welded, compact heat exchangers to transfer heat from the primary (reactor side) heat transport system to the secondary heat transport system. An intermediate heat exchanger will transfer this heat to downstream applications such as hydrogen production, process heat, and electricity generation. The channeled plates that make up the heat transfer surfaces of the intermediate heat exchanger will have to be assembled into an array by diffusion welding. This report describes the preliminary results of a scoping study that evaluated the diffusion welding process parameters and the resultant mechanical properties of diffusion welded joints using Alloy 800H. The long-term goal of the program is to progress towards demonstration of small heat exchanger unit cells fabricated with diffusion welds. Demonstration through mechanical testing of the unit cells will support American Society of Mechanical Engineers rules and standards development, reduce technical risk, and provide proof of concept for heat exchanger fabrication methods needed to deploy heat exchangers in several potential NGNP configurations.1 Researchers also evaluated the usefulness of modern thermodynamic and diffusion computational tools (Thermo-Calc and Dictra) in optimizing the parameters for diffusion welding of Alloy 800H. The modeling efforts suggested a temperature of 1150 C for 1 hour with an applied pressure of 5 MPa using 15 {micro}m nickel foil as joint filler to reduce chromium oxidation on the welded surfaces. Good agreement between modeled and experimentally determined concentration gradients was achieved

Magnetization reversal processes of isotropic permanent magnets with various inter-grain exchange interactions

Directory of Open Access Journals (Sweden)

Hiroshi Tsukahara

2017-05-01

Full Text Available We performed a large-scale micromagnetics simulation on a supercomputing system to investigate the properties of isotropic nanocrystalline permanent magnets consisting of cubic grains. In the simulation, we solved the Landau–Lifshitz–Gilbert equation under a periodic boundary condition for accurate calculation of the magnetization dynamics inside the nanocrystalline isotropic magnet. We reduced the inter-grain exchange interaction perpendicular and parallel to the external field independently. Propagation of the magnetization reversal process is inhibited by reducing the inter-grain exchange interaction perpendicular to the external field, and the coercivity is enhanced by this restraint. In contrast, when we reduce the inter-grain exchange interaction parallel to the external field, the coercivity decreases because the magnetization reversal process propagates owing to dipole interaction. These behaviors show that the coercivity of an isotropic permanent magnet depends on the direction of the inter-grain exchange interaction.

On the time-homogeneous Ornstein–Uhlenbeck process in the foreign exchange rates

Energy Technology Data Exchange (ETDEWEB)

Fonseca, Regina C.B. da, E-mail: regina@quimica-industrial.com [Department of Mathematics, Instituto Federal de Goiás, Goiânia, Goiás 74055-110 (Brazil); International Center for Condensed Matter Physics, Instituto de Física, Universidade de Brasília, Caixa Postal 04455, 70919-970, Brasília, Distrito Federal (Brazil); Matsushita, Raul Y. [Department of Statistics, Universidade de Brasília, 70919-970, Brasília, Distrito Federal (Brazil); Castro, Márcio T. de; Figueiredo, Annibal [International Center for Condensed Matter Physics, Instituto de Física, Universidade de Brasília, Caixa Postal 04455, 70919-970, Brasília, Distrito Federal (Brazil)

2015-10-02

Since Gaussianity and stationarity assumptions cannot be fulfilled by financial data, the time-homogeneous Ornstein–Uhlenbeck (THOU) process was introduced as a candidate model to describe time series of financial returns [1]. It is an Ornstein–Uhlenbeck (OU) process in which these assumptions are replaced by linearity and time-homogeneity. We employ the OU and THOU processes to analyze daily foreign exchange rates against the US dollar. We confirm that the OU process does not fit the data, while in most cases the first four cumulants patterns from data can be described by the THOU process. However, there are some exceptions in which the data do not follow linearity or time-homogeneity assumptions. - Highlights: • Gaussianity and stationarity assumptions replaced by linearity and time-homogeneity. • We revisit the time-homogeneous Ornstein–Uhlenbeck (THOU) process. • We employ the THOU process to analyze foreign exchange rates against the US dollar. • The first four cumulants patterns from data can be described by the THOU process.

On the time-homogeneous Ornstein–Uhlenbeck process in the foreign exchange rates

International Nuclear Information System (INIS)

Fonseca, Regina C.B. da; Matsushita, Raul Y.; Castro, Márcio T. de; Figueiredo, Annibal

2015-01-01

Since Gaussianity and stationarity assumptions cannot be fulfilled by financial data, the time-homogeneous Ornstein–Uhlenbeck (THOU) process was introduced as a candidate model to describe time series of financial returns [1]. It is an Ornstein–Uhlenbeck (OU) process in which these assumptions are replaced by linearity and time-homogeneity. We employ the OU and THOU processes to analyze daily foreign exchange rates against the US dollar. We confirm that the OU process does not fit the data, while in most cases the first four cumulants patterns from data can be described by the THOU process. However, there are some exceptions in which the data do not follow linearity or time-homogeneity assumptions. - Highlights: • Gaussianity and stationarity assumptions replaced by linearity and time-homogeneity. • We revisit the time-homogeneous Ornstein–Uhlenbeck (THOU) process. • We employ the THOU process to analyze foreign exchange rates against the US dollar. • The first four cumulants patterns from data can be described by the THOU process

Modeling of sorption processes on solid-phase ion-exchangers

Science.gov (United States)

Dorofeeva, Ludmila; Kuan, Nguyen Anh

2018-03-01

Research of alkaline elements separation on solid-phase ion-exchangers is carried out to define the selectivity coefficients and height of an equivalent theoretical stage for both continuous and stepwise filling of column by ionite. On inorganic selective sorbents the increase in isotope enrichment factor up to 0.0127 is received. Also, parametrical models that are adequately describing dependence of the pressure difference and the magnitude expansion in the ion-exchange layer from the flow rate and temperature have been obtained. The concentration rate value under the optimum realization conditions of process and depending on type of a selective material changes in a range 1.021÷1.092. Calculated results show agreement with experimental data.

Development of Electrically Switched Ion Exchange Process for Selective Ion Separations

International Nuclear Information System (INIS)

Rassat, Scot D.; Sukamto, Johanes H.; Orth, Rick J.; Lilga, Michael A.; Hallen, Richard T.

1999-01-01

The electrically switched ion exchange (ESIX) process, being developed at Pacific Northwest National Laboratory, provides an alternative separation method to selectively remove ions from process and waste streams. In the ESIX process, in which an electroactive ion exchange film is deposited onto a high surface area electrode, uptake and elution are controlled directly by modulating the electrochemical potential of the film. This paper addresses engineering issues necessary to fully develop ESIX for specific industrial alkali cation separation challenges. The cycling and chemical stability and alkali cation selectivity of nickel hexacyanoferrate (NiHCF) electroactive films were investigated. The selectivity of NiHCF was determined using cyclic voltammetry and a quartz crystal microbalance to quantify ion uptake in the film. Separation factors indicated a high selectivity for cesium and a moderate selectivity for potassium in high sodium content solutions. A NiHCF film with improved redox cycling and chemical stability in a simulated pulp mill process stream, a targeted application for ESIX, was also prepared and tested

Process for exchanging hydrogen isotopes between gaseous hydrogen and water

International Nuclear Information System (INIS)

Hindin, S. G.; Roberts, G. W.

1980-01-01

A process for exchanging isotopes of hydrogen, particularly tritium, between gaseous hydrogen and water is provided whereby gaseous hydrogen depeleted in tritium and liquid or gaseous water containing tritium are reacted in the presence of a metallic catalyst

Continuous desalting of refolded protein solution improves capturing in ion exchange chromatography: A seamless process.

Science.gov (United States)

Walch, Nicole; Jungbauer, Alois

2017-06-01

Truly continuous biomanufacturing processes enable an uninterrupted feed stream throughout the whole production without the need for holding tanks. We have utilized microporous anion and cation exchangers into which only salts, but not proteins, can penetrate into the pores for desalting of protein solutions, while diafiltration or dilution is usually employed for feed adjustments. Anion exchange and cation exchange chromatography columns were connected in series to remove both anions and cations. To increase operation performance, a continuous process was developed comprised of four columns. Continuous mode was achieved by staggered cycle operation, where one set of columns, consisting of one anion exchange and one cation exchange column, was loaded during the regeneration of the second set. Refolding, desalting and subsequent ion exchange capturing with a scFv as the model protein was demonstrated. The refolding solution was successfully desalted resulting in a consistent conductivity below 0.5 mS/cm from initial values of 10 to 11 mS/cm. With continuous operation process time could be reduced by 39% while productivity was increased to 163% compared to batch operation. Desalting of the protein solution resulted in up to 7-fold higher binding capacities in the subsequent ion exchange capture step with conventional protein binding resins. © 2017 The Authors. Biotechnology Journal published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Process Heat Exchanger Options for the Advanced High Temperature Reactor

Energy Technology Data Exchange (ETDEWEB)

Piyush Sabharwall; Eung Soo Kim; Michael McKellar; Nolan Anderson

2011-06-01

The work reported herein is a significant intermediate step in reaching the final goal of commercial-scale deployment and usage of molten salt as the heat transport medium for process heat applications. The primary purpose of this study is to aid in the development and selection of the required heat exchanger for power production and process heat application, which would support large-scale deployment.

Process Heat Exchanger Options for Fluoride Salt High Temperature Reactor

Energy Technology Data Exchange (ETDEWEB)

Piyush Sabharwall; Eung Soo Kim; Michael McKellar; Nolan Anderson

2011-04-01

The work reported herein is a significant intermediate step in reaching the final goal of commercial-scale deployment and usage of molten salt as the heat transport medium for process heat applications. The primary purpose of this study is to aid in the development and selection of the required heat exchanger for power production and process heat application, which would support large-scale deployment.

Process Heat Exchanger Options for Fluoride Salt High Temperature Reactor

International Nuclear Information System (INIS)

Sabharwall, Piyush; Kim, Eung Soo; McKellar, Michael; Anderson, Nolan

2011-01-01

The work reported herein is a significant intermediate step in reaching the final goal of commercial-scale deployment and usage of molten salt as the heat transport medium for process heat applications. The primary purpose of this study is to aid in the development and selection of the required heat exchanger for power production and process heat application, which would support large-scale deployment.

A Simulation Study of Inter Heat Exchanger Process in SI Cycle Process for Hydrogen Production

International Nuclear Information System (INIS)

Shin, Jae Sun; Cho, Sung Jin; Choi, Suk Hoon; Qasim, Faraz; Lee, Euy Soo; Park, Sang Jin; Lee, Heung N.; Park, Jae Ho; Lee, Won Jae

2014-01-01

SI Cyclic process is one of the thermochemical hydrogen production processes using iodine and sulfur for producing hydrogen molecules from water. VHTR (Very High Temperature Reactor) can be used to supply heat to hydrogen production process, which is a high temperature nuclear reactor. IHX (Intermediate Heat Exchanger) is necessary to transfer heat to hydrogen production process safely without radioactivity. In this study, the strategy for the optimum design of IHX between SI hydrogen process and VHTR is proposed for various operating pressures of the reactor, and the different cooling fluids. Most economical efficiency of IHX is also proposed along with process conditions

LITERATURE REVIEWS TO SUPPORT ION EXCHANGE TECHNOLOGY SELECTION FOR MODULAR SALT PROCESSING

Energy Technology Data Exchange (ETDEWEB)

King, W

2007-11-30

This report summarizes the results of literature reviews conducted to support the selection of a cesium removal technology for application in a small column ion exchange (SCIX) unit supported within a high level waste tank. SCIX is being considered as a technology for the treatment of radioactive salt solutions in order to accelerate closure of waste tanks at the Savannah River Site (SRS) as part of the Modular Salt Processing (MSP) technology development program. Two ion exchange materials, spherical Resorcinol-Formaldehyde (RF) and engineered Crystalline Silicotitanate (CST), are being considered for use within the SCIX unit. Both ion exchange materials have been studied extensively and are known to have high affinities for cesium ions in caustic tank waste supernates. RF is an elutable organic resin and CST is a non-elutable inorganic material. Waste treatment processes developed for the two technologies will differ with regard to solutions processed, secondary waste streams generated, optimum column size, and waste throughput. Pertinent references, anticipated processing sequences for utilization in waste treatment, gaps in the available data, and technical comparisons will be provided for the two ion exchange materials to assist in technology selection for SCIX. The engineered, granular form of CST (UOP IE-911) was the baseline ion exchange material used for the initial development and design of the SRS SCIX process (McCabe, 2005). To date, in-tank SCIX has not been implemented for treatment of radioactive waste solutions at SRS. Since initial development and consideration of SCIX for SRS waste treatment an alternative technology has been developed as part of the River Protection Project Waste Treatment Plant (RPP-WTP) Research and Technology program (Thorson, 2006). Spherical RF resin is the baseline media for cesium removal in the RPP-WTP, which was designed for the treatment of radioactive waste supernates and is currently under construction in Hanford, WA

LITERATURE REVIEWS TO SUPPORT ION EXCHANGE TECHNOLOGY SELECTION FOR MODULAR SALT PROCESSING

International Nuclear Information System (INIS)

King, W.

2007-01-01

This report summarizes the results of literature reviews conducted to support the selection of a cesium removal technology for application in a small column ion exchange (SCIX) unit supported within a high level waste tank. SCIX is being considered as a technology for the treatment of radioactive salt solutions in order to accelerate closure of waste tanks at the Savannah River Site (SRS) as part of the Modular Salt Processing (MSP) technology development program. Two ion exchange materials, spherical Resorcinol-Formaldehyde (RF) and engineered Crystalline Silicotitanate (CST), are being considered for use within the SCIX unit. Both ion exchange materials have been studied extensively and are known to have high affinities for cesium ions in caustic tank waste supernates. RF is an elutable organic resin and CST is a non-elutable inorganic material. Waste treatment processes developed for the two technologies will differ with regard to solutions processed, secondary waste streams generated, optimum column size, and waste throughput. Pertinent references, anticipated processing sequences for utilization in waste treatment, gaps in the available data, and technical comparisons will be provided for the two ion exchange materials to assist in technology selection for SCIX. The engineered, granular form of CST (UOP IE-911) was the baseline ion exchange material used for the initial development and design of the SRS SCIX process (McCabe, 2005). To date, in-tank SCIX has not been implemented for treatment of radioactive waste solutions at SRS. Since initial development and consideration of SCIX for SRS waste treatment an alternative technology has been developed as part of the River Protection Project Waste Treatment Plant (RPP-WTP) Research and Technology program (Thorson, 2006). Spherical RF resin is the baseline media for cesium removal in the RPP-WTP, which was designed for the treatment of radioactive waste supernates and is currently under construction in Hanford, WA

Anion-exchange resin-based desulfurization process. Final report

Energy Technology Data Exchange (ETDEWEB)

Sheth, A C; Dharmapurikar, R; Strevel, S D

1994-01-01

The following investigations were performed: (1) batch mode screening of eleven(11) commercially available resins and selection of three candidate resins for further evaluation in a fixed-bed setup. (2) Process variables study using three candidate resins in the fixed-bed setup and selection of the ``best`` resin for process economics development. (3) Exhaustion efficiency and solution concentration were found to be inversely related necessitating a trade-off between the resin cost versus the cost of evaporation/concentration of ensuing effluents. (4) Higher concentration of the HCO{sub 3}{sup {minus}} form of active sites over less active CO{sub 3}{sup 2{minus}} form of sites in the resin was believed to be the main reason for the observed increase in the equilibrium capacity of the resin at an elevated static CO{sub 2}-pressure. This Increase in capacity was found to level off around 80--120 psig range. The increase in CO{sub 2}-pressure, however, did not appear to affect the overall ion-exchange kinetics. (5) In the fixed-bed mode, the solution concentration was found to affect the equilibrium capacity of candidate resins. Their relationship was well satisfied by the Langmuir type non-linear equilibrium isotherm. Alternatively, the effect of solution concentration on overall ion-exchange kinetics varied from resin to resin. (6) Product inhibition effect on the resin was observed as an initial increase followed by a significant decrease in the resin`s equilibrium capacity for SO{sub 4}{sup 2{minus}} as the HCO{sub 3}{sup {minus}}/SO{sub 4}{sup 2{minus}} molar ratio in the solution was increased from 0 to 1.0. This ratio, however, did not affect the overall ion-exchange kinetics.

The impact of ion exchange media and filters on LLW processing

International Nuclear Information System (INIS)

James, K.L.; Miller, C.C.

1992-01-01

Optimized ion exchange media at Diablo Canyon have steadily improved the treatment of radioactive liquid waste. The activity released to the environment has been reduced while simultaneously reducing the volume of solid radwaste generated from processing radioactive liquids. This has lowered the liquid waste processing costs and reduced the number of radioactive shipments from the plant. A cobalt treatment technique was identified and successfully implemented prior to reactor coolant chemistry alteration. A cesium treatment using zeolite has been successfully implemented. A cobalt removal treatment, combining series cation ion exchange with submicron filtration, has successfully removed cobalt after reactor coolant chemistry alteration. A new carbon-based material will be monitored to find a media to remove cobalt from high-conductivity liquids. (author)

13C(α,n)16O reaction as the knock-out exchange process

International Nuclear Information System (INIS)

Kim, G.; Khajdarov, R.R.; Zaparov, Eh.A.

2000-01-01

S-factor for the 13 C(α,n) 16 O reaction is studied. In the framework of the simple phenomenological model this reaction is analysed as neutron knocked-out by α-particle exchange process. The analysis demonstrates the importance of taking into account 2p-state in 13 C. The 13 C(α,n) 16 O cross section is considered both as the knock-out exchange process and as it's combination with process through a compound nucleus. It was shown that for E α s value extrapolated to low energies is found to be noticeably larger that of R-matrix analysis. Different ways of improving the proposed model are discussed. (author)

Operating experiences of Heavy Water Plant at Talcher using bithermal ammonia-hydrogen exchange process (Paper No. 1.9)

International Nuclear Information System (INIS)

Haldar, T.K.; Manoj Kumar; Ramamurty, C.B.

1992-01-01

A heavy water plant employing bithermal ammonia-hydrogen exchange process was set up at Talcher (India). The energy consumption in the process is lower as compared to monothermal process. The plant performance was affected by various problems and has resulted in low heavy water production. The problems are: (i)formation of solid deposits, (ii)inability of exchange towers to process design gas flow rates, (iii)inadequate exchange efficiency of the sieve trays provided as exchange trays, and (iv)differential amide concentration in different plant sections. These problems and their effect on the overall plant performance are discussed in detail and modifications to improve the performance are suggested. (author). 4 figs

Convergence on Self - Generated vs. Crowdsourced Ideas in Crisis Response: Comparing Social Exchange Processes and Satisfaction with Process

DEFF Research Database (Denmark)

Seeber, Isabella; Merz, Alexander B.; Maier, Ronald

2017-01-01

engage in social exchange processes to converge on a few promising ideas. Traditionally, teams work on self-generated ideas. However, in a crowdsourcing scenario, such as public participation in crisis response, teams may have to process crowd-generated ideas. To better understand this new practice......Social media allow crowds to generate many ideas to swiftly respond to events like crises, public policy discourse, or online town hall meetings. This allows organizations and governments to harness the innovative power of the crowd. As part of this setting, teams that process crowd ideas must......, it is important to investigate how converging on crowdsourced ideas affects the social exchange processes of teams and resulting outcomes. We conducted a laboratory experiment in which small teams working in a crisis response setting converged on self-generated or crowdsourced ideas in an emergency response...

Mathematical modelling of thermal and flow processes in vertical ground heat exchangers

Directory of Open Access Journals (Sweden)

Pater Sebastian

2017-12-01

Full Text Available The main task of mathematical modelling of thermal and flow processes in vertical ground heat exchanger (BHE-Borehole Heat Exchanger is to determine the unit of borehole depth heat flux obtainable or transferred during the operation of the installation. This assignment is indirectly associated with finding the circulating fluid temperature flowing out from the U-tube at a given inlet temperature of fluid in respect to other operational parameters of the installation.

Engineering study for the treatment of spent ion exchange resin resulting from nuclear process applications

International Nuclear Information System (INIS)

Place, B.G.

1990-09-01

This document is an engineering study of spent ion exchange resin treatment processes with the purpose of identifying one or more suitable treatment technologies. Classifications of waste considered include all classes of low-level waste (LLW), mixed LLW, transuranic (TRU) waste, and mixed TRU waste. A total of 29 process alternatives have been evaluated. Evaluation parameters have included economic parameters (both total life-cycle costs and capital costs), demonstrated operability, environmental permitting, operational availability, waste volume reduction, programmatic consistency, and multiple utilization. The results of this study suggest that there are a number of alternative process configurations that are suitable for the treatment of spent ion exchange resin. The determinative evaluation parameters were economic variables (total life-cycle cost or capital cost) and waste volume reduction. Immobilization processes are generally poor in volume reduction. Thermal volume reduction processes tend to have high capital costs. There are immobilization processes and thermal volume reduction processes that can treat all classifications of spent ion exchange resin likely to be encountered. 40 refs., 19 figs., 17 tabs

Uranium refining process using ion exchange membrane

International Nuclear Information System (INIS)

Yamaguchi, Akira

1977-01-01

As for the method of refining uranium ore being carried out in Europe and America at present, uranium ore is roughly refined at the mine sites to yellow cake, then this is transported to refineries and refined by dry method. This method has the following faults, namely the number of processes is large, it requires expensive corrosion-resistant materials because of high temperature treatment, and the impurities in uranium tend to increase. On the other hand, in case of EXCER method, treatment is carried out at low temperature, and high purity uranium can be obtained, but the efficiency of electrolytic reduction process is extremely low, and economically infeasible. In the wet refining method called PNC process, uranium tetrafluoride is produced from uranium ore without making yellow cake, therefore the process is rationalized largely, and highly economical. The electrolytic reduction process in this method was developed by Asahi Chemical Industry Co., Ltd. by constructing the pilot plant in Ningyotoge Mine. The ion exchange membrane, the electrodes, and the problems concerning the process and the engineering for commercial plants were investigated. The electrolytic reduction process, the pilot plant, the development of the elements of electrolytic cells, the establishment of analytical process, the measurement of the electrolytic characteristics, the demonstration operation, and the life time of the electrolytic diaphragm are reported. (Kako, I.)

Study on the process variables in the anion exchange plutonium separation process

Energy Technology Data Exchange (ETDEWEB)

Nishimura, D T

1957-11-15

This report discusses the study of the process variables in the Anion Exchange Process Pilot Plant for the separation of plutonium from irradiated uranium. Variables associated with the feed, wash and elution cycles were studied with the aim of improving the quality of the final plutonium product, reduce cycling time and reagent requirements, and also to obtain data for prediction of resin column behaviour under various feed conditions. A cation resin column and a silica gel column were installed in the system and these were studied for plutonium recovery and product quality. The product obtained from the plant was acceptable in all the impurities except the associated gamma activity which was too high for easy product handling. (author)

Research of the heat exchanging processes running in the heating and hot water supply loops of the coil heat exchangers

Directory of Open Access Journals (Sweden)

Ірина Геннадіївна Шитікова

2016-11-01

Full Text Available The fuel-energy complex research has made it possible to disclose a huge power-saving potential in the municipal heat-and-power engineering. Power-and-resource-saving units and systems are becoming extremely urgent because of the power engineering crisis expansion. The self-adjusting heat supply system from the individual heating points with the heat-accumulating units and coil heat exchangers for independent heating and water supply systems has been examined. Coil heat exchangers are used in municipal heating for heat transfer (e.g. geothermal waters for the independent mains of the heating and hot water supply systems. The heat engineering calculation of the heating and accumulating unit with the coil heat exchanger for independent heat supply systems from individual heater was performed and experimental data were received at the experimental industrial unit under the laboratory conditions. The peculiarities of the flows in the intertubular space, their influence on the heat exchange and temperatures of the first and intermediate mains have been shown. It is important to know the processes running inside the apparatus to be able to improve the technical characteristics of the three-loop coil heat exchanger. The task solution will make it possible to save the materials consumption for the three-loop coil heat exchangers in the future

Application of ion-exchange unit in uranium extraction process in China (to be continued)

International Nuclear Information System (INIS)

Gong Chuanwen

2004-01-01

The application conditions of five different ion exchange units in uranium milling plant and wastewater treatment plant of uranium mine in China are introduced, including working parameters, existing problems and improvements. The advantages and disadvantages of these units are reviewed briefly. The procedure points to be followed in selecting ion exchange unit are recommended in the engineering design. The primary views are presented upon the application prospects of some ion exchange units in uranium extraction process in China

Quantitative description of proton exchange processes between water and endogenous and exogenous agents for WEX, CEST, and APT experiments.

Science.gov (United States)

Zhou, Jinyuan; Wilson, David A; Sun, Phillip Zhe; Klaus, Judith A; Van Zijl, Peter C M

2004-05-01

The proton exchange processes between water and solutes containing exchangeable protons have recently become of interest for monitoring pH effects, detecting cellular mobile proteins and peptides, and enhancing the detection sensitivity of various low-concentration endogenous and exogenous species. In this work, the analytic expressions for water exchange (WEX) filter spectroscopy, chemical exchange-dependent saturation transfer (CEST), and amide proton transfer (APT) experiments are derived by the use of Bloch equations with exchange terms. The effects of the initial states for the system, the difference between a steady state and a saturation state, and the relative contributions of the forward and backward exchange processes are discussed. The theory, in combination with numerical calculations, provides a useful tool for designing experimental schemes and assessing magnetization transfer (MT) processes between water protons and solvent-exchangeable protons. As an example, the case of endogenous amide proton exchange in the rat brain at 4.7 T is analyzed in detail. Copyright 2004 Wiley-Liss, Inc.

Medication errors in residential aged care facilities: a distributed cognition analysis of the information exchange process.

Science.gov (United States)

Tariq, Amina; Georgiou, Andrew; Westbrook, Johanna

2013-05-01

Medication safety is a pressing concern for residential aged care facilities (RACFs). Retrospective studies in RACF settings identify inadequate communication between RACFs, doctors, hospitals and community pharmacies as the major cause of medication errors. Existing literature offers limited insight about the gaps in the existing information exchange process that may lead to medication errors. The aim of this research was to explicate the cognitive distribution that underlies RACF medication ordering and delivery to identify gaps in medication-related information exchange which lead to medication errors in RACFs. The study was undertaken in three RACFs in Sydney, Australia. Data were generated through ethnographic field work over a period of five months (May-September 2011). Triangulated analysis of data primarily focused on examining the transformation and exchange of information between different media across the process. The findings of this study highlight the extensive scope and intense nature of information exchange in RACF medication ordering and delivery. Rather than attributing error to individual care providers, the explication of distributed cognition processes enabled the identification of gaps in three information exchange dimensions which potentially contribute to the occurrence of medication errors namely: (1) design of medication charts which complicates order processing and record keeping (2) lack of coordination mechanisms between participants which results in misalignment of local practices (3) reliance on restricted communication bandwidth channels mainly telephone and fax which complicates the information processing requirements. The study demonstrates how the identification of these gaps enhances understanding of medication errors in RACFs. Application of the theoretical lens of distributed cognition can assist in enhancing our understanding of medication errors in RACFs through identification of gaps in information exchange. Understanding

Ammonia-water exchange front end process for ammonia-hydrogen heavy water plants (Preprint No. PD-1)

International Nuclear Information System (INIS)

Sadhukhan, H.K.; Varadarajan, T.G.; Nair, N.K.; Das, S.K.; Nath, G.K.

1989-04-01

The ammonia-hydrogen exchange process, which utilizes the deutrium exchange between liquid ammonia and gaseous hydrogen is a parasitic process and the heavy water plants (HWP) based on this process has to be linked with the fertilizer plant (FP) for its enormous requirements of hydrogen (synthesis gas, N 2 +3H 2 ). This dependence of HWP on FP gives rise to certain constraints which are listed. These deficiencies of the ammonia-hydrogen process can be overcome to a great extent by delinking the HWP from FP by incorporating NH 3 -H 2 O exchange as the front end step. In addition to the elimination of the above limitations, by employing water as the ultimate feed for the HWP, the plant capacity can be increased substantially and this would go a long way in achieving economies of the large capacity plants. A schematic diagram of this integrated plant is given. Some of the results of developmental efforts and feasibility studies of this NH 3 -H 2 O exchange are briefly reviewed. (author). 4 figs

Combined electrolysis catalytic exchange (CECE) process for hydrogen isotope separation

International Nuclear Information System (INIS)

Hammerli, M.; Stevens, W.H.; Butler, J.P.

1978-01-01

Hydrogen isotopes can be separated efficiently by a process which combines an electrolysis cell with a trickle bed column packed with a hydrophobic platinum catalyst. The column effects isotopic exchange between countercurrent streams of electrolytic hydrogen and liquid water while the electrolysis cell contributes to isotope separation by virtue of the kinetic isotope effect inherent in the hydrogen evolution reaction. The main features of the CECE process for heavy water production are presented as well as a discussion of the inherent positive synergistic effects, and other advantages and disadvantages of the process. Several potential applications of the process in the nuclear power industry are discussed. 3 figures, 2 tables

Process control analysis requirement in NH3-H2 exchange bi-thermal Heavy Water Plant (Talcher) (Paper No. 6.8)

International Nuclear Information System (INIS)

Pattnaik, S.P.; Mishra, G.C.

1992-01-01

Heavy Water Plant, Talcher is based on bithermal NH 3 -H 2 exchange process. Isotopic exchange of deuterium takes place between gaseous hydrogen and liquid ammonia with potassium amide as catalyst. The process control analysis requirement in NH 3 -H 2 exchange dual temperature process is described. (author). 4 refs., 4 figs

Heat exchanger for coal gasification process

Science.gov (United States)

Blasiole, George A.

1984-06-19

This invention provides a heat exchanger, particularly useful for systems requiring cooling of hot particulate solids, such as the separated fines from the product gas of a carbonaceous material gasification system. The invention allows effective cooling of a hot particulate in a particle stream (made up of hot particulate and a gas), using gravity as the motive source of the hot particulate. In a preferred form, the invention substitutes a tube structure for the single wall tube of a heat exchanger. The tube structure comprises a tube with a core disposed within, forming a cavity between the tube and the core, and vanes in the cavity which form a flow path through which the hot particulate falls. The outside of the tube is in contact with the cooling fluid of the heat exchanger.

Resonance charge exchange processes

International Nuclear Information System (INIS)

Duman, E.L.; Evseev, A.V.; Eletskij, A.V.; Radtsig, A.A.; Smirnov, B.M.

1979-01-01

The calculation results for the resonance charge exchange cross sections for positive and negative atomic and molecular ions are given. The calculations are performed on the basis of the asymptotic theory. The factors affecting the calculation accuracy are analysed. The calculation data for 28 systems are compared with the experiment

Process Control Security in the Cybercrime Information Exchange NICC

OpenAIRE

Luiijf, H.A.M.

2009-01-01

Detecting, investigating and prosecuting cybercrime? Extremely important, but not really the solution for the problem. Prevention is better! The sectors that have joined the Cybercrime Information Exchange have accepted the challenge of ensuring the effectiveness of the (information) security of process control systems (PCS), including SCADA. This publication makes it clear why it is vital that organizations establish and maintain control over the security of the information and communication...

EPR Studies of Spin-Spin Exchange Processes: A Physical Chemistry Experiment.

Science.gov (United States)

Eastman, Michael P.

1982-01-01

Theoretical background, experimental procedures, and analysis of experimental results are provided for an undergraduate physical chemistry experiment on electron paramagnetic resonance (EPR) linewidths. Source of line broadening observed in a spin-spin exchange process between radicals formed in aqueous solutions of potassium peroxylamine…

Modelling on optimal portfolio with exchange rate based on discontinuous stochastic process

Science.gov (United States)

Yan, Wei; Chang, Yuwen

2016-12-01

Considering the stochastic exchange rate, this paper is concerned with the dynamic portfolio selection in financial market. The optimal investment problem is formulated as a continuous-time mathematical model under mean-variance criterion. These processes follow jump-diffusion processes (Weiner process and Poisson process). Then the corresponding Hamilton-Jacobi-Bellman(HJB) equation of the problem is presented and its efferent frontier is obtained. Moreover, the optimal strategy is also derived under safety-first criterion.

Cumulative Significance of Hyporheic Exchange and Biogeochemical Processing in River Networks

Science.gov (United States)

Harvey, J. W.; Gomez-Velez, J. D.

2014-12-01

Biogeochemical reactions in rivers that decrease excessive loads of nutrients, metals, organic compounds, etc. are enhanced by hydrologic interactions with microbially and geochemically active sediments of the hyporheic zone. The significance of reactions in individual hyporheic flow paths has been shown to be controlled by the contact time between river water and sediment and the intrinsic reaction rate in the sediment. However, little is known about how the cumulative effects of hyporheic processing in large river basins. We used the river network model NEXSS (Gomez-Velez and Harvey, submitted) to simulate hyporheic exchange through synthetic river networks based on the best available models of network topology, hydraulic geometry and scaling of geomorphic features, grain size, hydraulic conductivity, and intrinsic reaction rates of nutrients and metals in river sediment. The dimensionless reaction significance factor, RSF (Harvey et al., 2013) was used to quantify the cumulative removal fraction of a reactive solute by hyporheic processing. SF scales reaction progress in a single pass through the hyporheic zone with the proportion of stream discharge passing through the hyporheic zone for a specified distance. Reaction progress is optimal where the intrinsic reaction timescale in sediment matches the residence time of hyporheic flow and is less efficient in longer residence time hyporheic flow as a result of the decreasing proportion of river flow that is processed by longer residence time hyporheic flow paths. In contrast, higher fluxes through short residence time hyporheic flow paths may be inefficient because of the repeated surface-subsurface exchanges required to complete the reaction. Using NEXSS we found that reaction efficiency may be high in both small streams and large rivers, although for different reasons. In small streams reaction progress generally is dominated by faster pathways of vertical exchange beneath submerged bedforms. Slower exchange

Document Management and Exchange System – Supporting Education Process

Directory of Open Access Journals (Sweden)

Emil Egredzija

2010-03-01

Full Text Available Development and implementation of new technologies are very important in education. One of the most challenging tasks in the education process is to build efficient and cost-friendly system for content management and exchange. The system has to be reliable, easy manageable and open. Centralized storage, secured access, and ubiquitous client technologies have emerged as best-practice solutions in engineering that kind of services. Users can easily publish or exchange documents and not need to worry about their distribution, storage or technical skills required for efficient document management. The system that will be presented is built on open source technologies and is deployable on all today's popular web software platforms. The web server, the programming language and operating system that are used to build and deploy such a system are all non-proprietary and completely open because our mission was to build system that can be easily extended and not limited by its corporate license. The system uses security mechanisms such as user group access policy, operating system level security (file system and secured data storage in database. Because of the growing need for document management in education process we believe that this project will find its place in practice.

Dual cell conductivity during ionic exchange processes: the intelligent transmitter EXA DC 400

International Nuclear Information System (INIS)

Mier, A.

1997-01-01

Why is differential conductivity important versus standard conductivity measurement? That entirely depends on the application. If we have a process where the conductivity changes ge.. Cation exchanger, then standard conductivity measurement is not appropriate. With dual cell conductivity we can rate the process and eliminate conductivity changes outside the process. Therefore we achieve more precise control or monitoring of that process. (Author)

Improved protein hydrogen/deuterium exchange mass spectrometry platform with fully automated data processing.

Science.gov (United States)

Zhang, Zhongqi; Zhang, Aming; Xiao, Gang

2012-06-05

Protein hydrogen/deuterium exchange (HDX) followed by protease digestion and mass spectrometric (MS) analysis is accepted as a standard method for studying protein conformation and conformational dynamics. In this article, an improved HDX MS platform with fully automated data processing is described. The platform significantly reduces systematic and random errors in the measurement by introducing two types of corrections in HDX data analysis. First, a mixture of short peptides with fast HDX rates is introduced as internal standards to adjust the variations in the extent of back exchange from run to run. Second, a designed unique peptide (PPPI) with slow intrinsic HDX rate is employed as another internal standard to reflect the possible differences in protein intrinsic HDX rates when protein conformations at different solution conditions are compared. HDX data processing is achieved with a comprehensive HDX model to simulate the deuterium labeling and back exchange process. The HDX model is implemented into the in-house developed software MassAnalyzer and enables fully unattended analysis of the entire protein HDX MS data set starting from ion detection and peptide identification to final processed HDX output, typically within 1 day. The final output of the automated data processing is a set (or the average) of the most possible protection factors for each backbone amide hydrogen. The utility of the HDX MS platform is demonstrated by exploring the conformational transition of a monoclonal antibody by increasing concentrations of guanidine.

Thermal design of heat-exchangeable reactors using a dry-sorbent CO2 capture multi-step process

International Nuclear Information System (INIS)

Moon, Hokyu; Yoo, Hoanju; Seo, Hwimin; Park, Yong-Ki; Cho, Hyung Hee

2015-01-01

The present study proposes a multi-stage CO 2 capture process that incorporates heat-exchangeable fluidized-bed reactors. For continuous multi-stage heat exchange, three dry regenerable sorbents: K 2 CO 3 , MgO, and CaO, were used to create a three-stage temperature-dependent reaction chain for CO 2 capture, corresponding to low (50–150 °C), middle (350–650 °C), and high (750–900 °C) temperature stages, respectively. Heat from carbonation in the high and middle temperature stages was used for regeneration for the middle and low temperature stages. The feasibility of this process is depending on the heat-transfer performance of the heat-exchangeable fluidized bed reactors as the focus of this study. The three-stage CO 2 capture process for a 60 Nm 3 /h CO 2 flow rate required a reactor area of 0.129 and 0.130 m 2 for heat exchange between the mid-temperature carbonation and low-temperature regeneration stages and between the high-temperature carbonation and mid-temperature regeneration stages, respectively. The reactor diameter was selected to provide dense fluidization conditions for each bed with respect to the desired flow rate. The flow characteristics and energy balance of the reactors were confirmed using computational fluid dynamics and thermodynamic analysis, respectively. - Highlights: • CO 2 capture process is proposed using a multi-stage process. • Reactor design is conducted considering heat exchangeable scheme. • Reactor surface is designed by heat transfer characteristics of fluidized bed

The advanced CECE process for enriching tritium by the chemical exchange method with a hydrophobic catalyst

International Nuclear Information System (INIS)

Kitamoto, Asashi; Shimizu, Masami; Masui, Takashi.

1992-01-01

The monothermal chemical exchange process with electrolysis, i.e., CECE process, was an effective method for enriching and removing tritium from tritiated water with low to middle level activity. The purpose of this study is to propose the theoretical background of the two-parameter evaluation method, which is based on a two-step isotope exchange reaction between hydrogen gas and liquid water, for improvement of the performance of a hydrophobic catalyst by a trickle bed-type column. Finally, a two-parameter method could attain the highest performance of isotope separation and the lowest liquid holdup for a trickle bed-type column. Therefore, this method will present some effective and practical procedures in scaling up a tritium enrichment process. The main aspect of the CECE process in engineering design and system evaluation was to develop the isotope exchange column with a high performance catalyst. (author)

Ion exchange media testing for processing recyclable and nonrecyclable liquids at Diablo Canyon Power Plant

International Nuclear Information System (INIS)

James, K.L.; Miller, C.C.

1989-01-01

This paper reports on several ion exchange materials tested for processing nonrecyclable and recyclable liquid wastes at Diablo Canyon Power Plant. These ion exchange materials include inorganic Durasil media, natural and synthetic zeolites, and various organic resins. Additional tests were performed using a polyelectrolyte pretreatment technique to enhance processing of liquid wastes by ion exchange. A 9:1 ratio of cation to anion resin, consisting of IRN-77 and Sybron A-642 was effective in decontaminating cesium and cobalt radionuclides for low conductivity nonrecyclable liquids. A mixture of zeolite and Durasil media was most effective in removing cesium and cobalt from nonrecyclable high conductivity liquids. The experimental Dow resins achieved the best results in decontaminating recyclable liquids and minimized the effluent levels of chlorides, sulfates, and silica

A study of an ion-exchange process for separation of strontium and yttrium

International Nuclear Information System (INIS)

Mubarek, M.A.

1980-01-01

A study has been carried out to determine optimum conditions for the separation of strontium and yttrium by ion-exchange. The parameters of interest for such separation such as the dimensions of the ion-exchange columns, flow rates through the columns and pH values of the solutions, which affect the overall yield in the process, have been investigated. Application of this method for routine quantitative determinations of Sr-90 in environmental samples, particularly the wet-ashed biological materials has also been studied. The method, although a rapid and convenient one has not been found to yield consistent results probably due to the requirement of stringent analytical controls during the process. (author)

Efficiency of Al2O3 supported palladium sorbents in the process of hydrogen isotope exchange

International Nuclear Information System (INIS)

Andreev, B.M.; Perevezentsev, A.N.; Yasenkov, V.I.

1981-01-01

It is found that in the hydrogen-palladium system while applying the metal to aluminium oxide a considerable increase of the heterogeneous hydrogen isotopic exchange rate is observed due to the increase of its specific surface at 167-298 K temperatures and 350-500 Torr hydrogen pressures. It is shown that in the process of thermal treatment of the supported palladium sorbent resulting in reconstruction of the carrier porous structure, as well as in increasing the metal crystal size, the change of the stage, limiting the isotopic exchange process, occurs. The values of the rate and energy of activation of the hydrogen isotopic exchange are presented [ru

Steam condensation process in a power production cycle and heat exchanger for it

International Nuclear Information System (INIS)

Tondeur, Gerard; Andro, Jean; Marjollet, Jacques; Pouderoux, Pierre.

1982-01-01

Steam condensation process in a power production cycle by expansion in turbines, characterized by the fact that this condensation is performed by the vaporization of a coolant with a vaporization temperature at atmospheric pressure lower than that of water, and that the vaporized coolant fluid is expanded in a turbine and then condensed by heat exchange with cold water being heated, while the liquefied coolant is recompressed and used for heat exchange with the steam to be condensed [fr

Local description of the energy transfer process in a packed bed heat exchanger

International Nuclear Information System (INIS)

Costa, M.L.M.; Sampaio, R.; Gama, R.M.S. da.

1990-01-01

The energy transfer process in a packed-bed heat exchanger, in counter0flow arrangement is considered. The phenomenon is described through a Continuum Theory of Mixtures approach, in which fluid and solid (porous matrix) are regarded as continuous constituents possessing, each one, its own temperature and velocity fields. The heat 'exchangers consists of two channels, separated by an impermeable wall without thermal resistence, in which there exists a saturated flow. Some particular cases are simulated. (author)

Investigation of ammonia air-surface exchange processes in a ...

Science.gov (United States)

Recent assessments of atmospheric deposition in North America note the increasing importance of reduced (NHx = NH3 + NH4+) forms of nitrogen (N) relative to oxidized forms. This shift in in the composition of inorganic nitrogen deposition has both ecological and policy implications. Deposition budgets developed from inferential models applied at the landscape scale, as well as regional and global chemical transport models, indicate that NH3 dry deposition contributes a significant portion of inorganic N deposition in many areas. However, the bidirectional NH3 flux algorithms employed in these models have not been extensively evaluated for North American conditions (e.g, atmospheric chemistry, meteorology, biogeochemistry). Further understanding of the processes controlling NH3 air-surface exchange in natural systems is critically needed. Based on preliminary results from the Southern Appalachian Nitrogen Deposition Study (SANDS), this presentation examines processes of NH3 air-surface exchange in a deciduous montane forest at the Coweeta Hydrologic Laboratory in western North Carolina. A combination of measurements and modeling are used to investigate net fluxes of NH3 above the forest and sources and sinks of NH3 within the canopy and forest floor. Measurements of biogeochemical NH4+ pools are used to characterize emission potential and NH3 compensation points of canopy foliage (i.e., green vegetation), leaf litter, and soil and their relation to NH3 fluxes

Catalytic process for tritium exchange reaction

International Nuclear Information System (INIS)

Hansoo Lee; Kang, H.S.; Paek, S.W.; Hongsuk Chung; Yang Geun Chung; Sook Kyung Lee

2001-01-01

The catalytic activities for a hydrogen isotope exchange were measured through the reaction of a vapor and gas mixture. The catalytic activity showed to be comparable with the published data. Since the gas velocity is relatively low, the deactivation was not found clearly during the 5-hour experiment. Hydrogen isotope transfer experiments were also conducted through the liquid phase catalytic exchange reaction column that consisted of a catalytic bed and a hydrophilic bed. The efficiencies of both the catalytic and hydrophilic beds were higher than 0.9, implying that the column performance was excellent. (author)

Application of the atomic absorption technical to available the concentration of silver ions incorporated in glass matrix by ionic exchange process

International Nuclear Information System (INIS)

Mendes, E.; Silva, K.F.; Teixeira, A.; Silva, L.; Paula, M.M.S.; Angioletto, E.; Riella, H.G.; Fiori, M. A.

2009-01-01

Ion specimens can be incorporated in glasses or natural clays by ionic exchange process with different concentrations dependent of matrix's type and of the ionic exchange parameters. In particular, the incorporation of silver ions presents high interest by its biocidal properties. A compound contending ion silver specimens presents bactericidal and fungicidal properties with effect proportional to ion concentration. This work presents results about application of the atomic absorption technical to determine the silver ion concentration incorporated in a glass matrix by ionic exchange process. The ionic exchange experiments were realized with different AgNO 3 concentration and constant temperature. After ionic exchange process, the glass samples were submitted to characterization by Energy Dispersive X-Ray Spectroscopy and Atomic Absorption Techniques. The comparative results between different techniques showed that atomic absorption technical is adequate to determine ion silver concentration incorporated in the glass matrix after ionic exchange process. (author)

IAEA technical meeting on 'Technical aspects of atomic and molecular data processing and exchange'. Summary report

International Nuclear Information System (INIS)

Humbert, Denis

2004-03-01

The proceedings of the IAEA Advisory Group Meeting on 'Technical Aspects of Atomic and Molecular Data Processing and Exchange' (17th Meeting of A+M Data Centres and ALADDIN Network), held on 6-7 October, 2003 in Vienna, Austria are briefly described. The meeting conclusions and recommendations on the priorities in A+M data compilation and evaluation, and on the technical aspects of data processing, exchange, and distribution are also presented. (author)

Considerations on the question of applying ion exchange or reverse osmosis methods in boiler feedwater processing

International Nuclear Information System (INIS)

Marquardt, K.; Dengler, H.

1976-01-01

This consideration is to show that the method of reverse osmosis presents in many cases an interesting and economical alternative to part and total desolination plants using ion exchangers. The essential advantages of the reverse osmosis are a higher degree of automization, no additional salting of the removed waste water, small constructional volume of the plant as well as favourable operational costs with increasing salt content of the crude water to be processed. As there is a relatively high salt breakthrough compared to the ion exchange method, the future tendency in boiler feedwater processing will be more towards a combination of methods of reverse osmosis and post-purification through continuous ion exchange methods. (orig./LH) [de

Hydrogen-water isotopic exchange process

International Nuclear Information System (INIS)

Cheung, H.

1983-01-01

Deuterium is concentrated in a hydrogen-water isotopic exchange process enhanced by the use of catalyst materials in cold and hot tower contacting zones. Water is employed in a closed liquid recirculation loop that includes the cold tower, in which deuterium is concentrated in the water, and the upper portion of the hot tower in which said deuterium is concentrated in the hydrogen stream. Feed water is fed to the lower portion of said hot tower for contact with the circulating hydrogen stream. The feed water does not contact the water in the closed loop. Catalyst employed in the cold tower and the upper portion of the hot tower, preferably higher quality material, is isolated from impurities in the feed water that contacts only the catalyst, preferably of lower quality, in the lower portion of the hot zone. The closed loop water passes from the cold zone to the dehumidification zone, and a portion of said water leaving the upper portion of the hot tower can be passed to the humidification zone and thereafter recycled to said closed loop. Deuterium concentration is enhanced in said catalytic hydrogen-water system while undue retarding of catalyst activity is avoided

Cancellation of Glauber gluon exchange in the double Drell-Yan process

International Nuclear Information System (INIS)

Diehl, Markus; Gaunt, Jonathan R.; Ostermeier, Daniel; Ploessl, Peter; Schaefer, Andreas

2015-10-01

An essential part of any factorisation proof is the demonstration that the exchange of Glauber gluons cancels for the considered observable. We show this cancellation at all orders for double Drell-Yan production (the double parton scattering process in which a pair of electroweak gauge bosons is produced) both for the integrated cross section and for the cross section differential in the transverse boson momenta. In the process of constructing this proof, we also revisit and clarify some issues regarding the Glauber cancellation argument and its relation to the rest of the factorisation proof for the single Drell-Yan process.

A new type separation column for the water-hydrogen isotope catalytic exchange process

International Nuclear Information System (INIS)

Fedorchenko, O.A.; Alekseev, I.A.; Trenin, V.D.

2001-01-01

The catalytic water/hydrogen isotope exchange process is by right considered the most attractive for the solution a number of urgent problems of hydrogen isotope separation. A new type exchange reaction column is described and studied in details by computer simulation and with the help of McCabe-Thiele diagrams. It is shown that the new column in comparison with a traditional one needs less catalyst quantity and a smaller diameter for the solving of the same separation tasks. Generalized calculation data are presented in graphical form

General Top-Down Ion Exchange Process for the Growth of Epitaxial Chalcogenide Thin Films and Devices

KAUST Repository

Xia, Chuan

2016-12-30

We demonstrate a versatile top-down ion exchange process, done at ambient temperature, to form epitaxial chalcogenide films and devices, with nanometer scale thickness control. To demonstrate the versatility of our process we have synthesized (1) epitaxial chalcogenide metallic and semiconducting films and (2) free-standing chalcogenide films and (3) completed in situ formation of atomically sharp heterojunctions by selective ion exchange. Epitaxial NiCo2S4 thin films prepared by our process show 115 times higher mobility than NiCo2S4 pellets (23 vs 0.2 cm(2) V-1 s(-1)) prepared by previous reports. By controlling the ion exchange process time, we made free-standing epitaxial films of NiCo2S4 and transferred them onto different substrates. We also demonstrate in situ formation of atomically sharp, lateral Schottky diodes based on NiCo2O4/NiCo2S4 heterojunction, using a single ion exchange step. Additionally, we show that our approach can be easily extended to other chalcogenide semiconductors. Specifically, we used our process to prepare Cu1.8S thin films with mobility that matches single crystal Cu1.8S (25 cm(2) V-1 s(-1)), which is ca. 28 times higher than the previously reported Cu1.8S thin film mobility (0.58 cm(2) V-1 s(-1)), thus demonstrating the universal nature of our process. This is the first report in which chalcogenide thin films retain the epitaxial nature of the precursor oxide films, an approach that will be useful in many applications.

Transition density of charge-exchange processes

International Nuclear Information System (INIS)

Lovas, R.G.

1983-01-01

The transition density between parent and analogue states is studied with special reference to its role in charge-exchange nuclear reactions. The structure of the target nucleus is described in a perturbative approach, in which the Coulomb and asymmetry potentials mix the eigenstates of a charge-independent single-particle Hamiltonian. In this model formulae are derived for the transition density, the Coulomb displacement energy and the neutron-proton density difference, and their relationship is used to estimate the transition density. This estimate shows that: the largest contribution comes from the density of the excess neutrons; the weight of the Coulomb-mixing effect is small up to excess neutron number 10, and grows rapidly beyond; the weight of the core polarization term induced by the excess neutrons is modest and is the same for all nuclei. It is indicated that the Coulomb effect may explain the departure from the Lane model of nucleon charge-exchange scattering found for heavy nuclei, whereas the core polarization may account for the observed anomalous dependence of the deg 0 pion charge-exchange cross section on the number of excess neutrons. (author)

Atmosphere-soil-vegetation model including CO2 exchange processes: SOLVEG2

International Nuclear Information System (INIS)

Nagai, Haruyasu

2004-11-01

A new atmosphere-soil-vegetation model named SOLVEG2 (SOLVEG version 2) was developed to study the heat, water, and CO 2 exchanges between the atmosphere and land-surface. The model consists of one-dimensional multilayer sub-models for the atmosphere, soil, and vegetation. It also includes sophisticated processes for solar and long-wave radiation transmission in vegetation canopy and CO 2 exchanges among the atmosphere, soil, and vegetation. Although the model usually simulates only vertical variation of variables in the surface-layer atmosphere, soil, and vegetation canopy by using meteorological data as top boundary conditions, it can be used by coupling with a three-dimensional atmosphere model. In this paper, details of SOLVEG2, which includes the function of coupling with atmosphere model MM5, are described. (author)

The Socialization of Newcomers into Organizations: Integrating Learning and Social Exchange Processes

Science.gov (United States)

Korte, Russell F.

2007-01-01

Traditional views of socialization focus primarily on the passive learning by the newcomer of the expectations of the organization. Theorizing and research on cognitive learning and social exchange indicate that the socialization process is vastly more complex. This paper views socialization through the lenses of cognitive learning and social…

Thermal Performance Analysis For Small Ion-Exchange Cesium Removal Process

International Nuclear Information System (INIS)

Lee, S.; King, W.

2009-01-01

The In-Riser Ion Exchange program focuses on the development of in-tank systems to decontaminate high level waste (HLW) salt solutions at the Savannah River Site (SRS) and the Hanford Site. Small Column Ion Exchange (SCIX) treatment for cesium removal is a primary in-riser technology for decontamination prior to final waste immobilization in Saltstone. Through this process, radioactive cesium from the salt solution is adsorbed onto the ion exchange media which is packed within a flow-through column. Spherical Resorcinol-Formaldehyde (RF) is being considered as the ion exchange media for the application of this technology at both sites. A packed column loaded with media containing radioactive cesium generates significant heat from radiolytic decay. Under normal operating conditions, process fluid flow through the column can provide adequate heat removal from the columns. However, in the unexpected event of loss of fluid flow or fluid drainage from the column, the design must be adequate to handle the thermal load to avoid unacceptable temperature excursions. Otherwise, hot spots may develop locally which could degrade the performance of the ion-exchange media or the temperature could rise above column safety limits. Data exists which indicates that performance degradation with regard to cesium removal occurs with RF at 65C. In addition, the waste supernate solution will boil around 130C. As a result, two temperature limits have been assumed for this analysis. An additional upset scenario was considered involving the loss of the supernate solution due to inadvertent fluid drainage through the column boundary. In this case, the column containing the loaded media could be completely dry. This event is expected to result in high temperatures that could damage the column or cause the RF sorbent material to undergo undesired physical changes. One objective of these calculations is to determine the range of temperatures that should be evaluated during testing with the RF

Heterogeneously catalyzed deuterium separation processes: Hydrogen-water exchange studies at elevated temperatures and pressures

International Nuclear Information System (INIS)

Halliday, J.D.; Rolston, J.H.; Au, J.C.; Den Hartog, J.; Tremblay, R.R.

1985-01-01

New processes for the separation of hydrogen isotopes are required to produce heavy water for CANDU nuclear reactors and to extract tritium formed in the moderator during reactor operation. Wetproofed platinum catalysts capable of promoting rapid exchange of isotopes between countercurrent flows of hydrogen and liquid water in packed columns have been developed at CRNL over the past 15 years. These catalysts provide a catalystic surface for the gas phase exchange reaction H/sub 2/O/sub (v)/ + HD/sub (g)/ ↔ HDO/sub (v)/ + H/sub 2(g)/ as well as a large liquid surface for the liquid phase isotope transfer reaction HDO/sub (v)/ + H/sub 2/O/sub (iota)/↔HDO/sub (iota)/+H/sub 2/O/sub (v)/. Any economic stand-alone heavy water separation process, based on bithermal hydrogen-water exchange over wetproofed platinum catalysts, requires rapid overall exchange of isotopes between two phases at two temperatures. Catalysts developed for cold tower operation at 25-60 0 C are now being tested in a laboratory scale stainless steel trickle bed reactor for performance and stability at simulated hot tower conditions, 150 0 C and 2.0 MPa pressure. Catalytically active layers containing platinum supported on carbon or crystalline silica and wetproofed with Teflon have been prepared on ceramic spheres and stainless steel screening and tested in both random and ordered bed columns

Engineering evaluation of selective ion-exchange radioactive waste processing at Susquehanna Nuclear Power Plant: Final report

International Nuclear Information System (INIS)

Vance, J.N.

1989-01-01

This final report describes the work performed of an engineering feasibility evaluation of the use and benefits of a selective ion exchange treatment process in the Susquehanna radwaste system. The evaluation addressed operability and processing capability concerns, radiological impacts of operating in the radwaste discharge mode, required hardware modifications to the radwaste and plant make-up systems, impacts on plant water quality limits and impacts on higher waste classifications. An economic analysis is also reported showing the economic benefit of the use of selective ion exchange. 1 ref., 4 figs., 13 tabs

Knowledge exchange processes in organizations and policy arenas: a narrative systematic review of the literature.

Science.gov (United States)

Contandriopoulos, Damien; Lemire, Marc; Denis, Jean-Louis; Tremblay, Emile

2010-12-01

This article presents the main results from a large-scale analytical systematic review on knowledge exchange interventions at the organizational and policymaking levels. The review integrated two broad traditions, one roughly focused on the use of social science research results and the other focused on policymaking and lobbying processes. Data collection was done using systematic snowball sampling. First, we used prospective snowballing to identify all documents citing any of a set of thirty-three seminal papers. This process identified 4,102 documents, 102 of which were retained for in-depth analysis. The bibliographies of these 102 documents were merged and used to identify retrospectively all articles cited five times or more and all books cited seven times or more. All together, 205 documents were analyzed. To develop an integrated model, the data were synthesized using an analytical approach. This article developed integrated conceptualizations of the forms of collective knowledge exchange systems, the nature of the knowledge exchanged, and the definition of collective-level use. This literature synthesis is organized around three dimensions of context: level of polarization (politics), cost-sharing equilibrium (economics), and institutionalized structures of communication (social structuring). The model developed here suggests that research is unlikely to provide context-independent evidence for the intrinsic efficacy of knowledge exchange strategies. To design a knowledge exchange intervention to maximize knowledge use, a detailed analysis of the context could use the kind of framework developed here. © 2010 Milbank Memorial Fund. Published by Wiley Periodicals Inc.

On the time-homogeneous Ornstein-Uhlenbeck process in the foreign exchange rates

Science.gov (United States)

da Fonseca, Regina C. B.; Matsushita, Raul Y.; de Castro, Márcio T.; Figueiredo, Annibal

2015-10-01

Since Gaussianity and stationarity assumptions cannot be fulfilled by financial data, the time-homogeneous Ornstein-Uhlenbeck (THOU) process was introduced as a candidate model to describe time series of financial returns [1]. It is an Ornstein-Uhlenbeck (OU) process in which these assumptions are replaced by linearity and time-homogeneity. We employ the OU and THOU processes to analyze daily foreign exchange rates against the US dollar. We confirm that the OU process does not fit the data, while in most cases the first four cumulants patterns from data can be described by the THOU process. However, there are some exceptions in which the data do not follow linearity or time-homogeneity assumptions.

Differential multiple quantum relaxation caused by chemical exchange outside the fast exchange limit

International Nuclear Information System (INIS)

Wang Chunyu; Palmer, Arthur G.

2002-01-01

Differential relaxation of multiple quantum coherences is a signature for chemical exchange processes in proteins. Previous analyses of experimental data have used theoretical descriptions applicable only in the limit of fast exchange. Theoretical expressions for differential relaxation rate constants that are accurate outside fast exchange are presented for two-spin-system subject to two-site chemical exchange. The theoretical expressions are validated using experimental results for 15 N- 1 H relaxation in basic pancreatic trypsin inhibitor. The new theoretical expression is valuable for identification and characterization of exchange processes in proteins using differential relaxation of multiple quantum coherences

Removal of disinfection by-product precursors by coagulation and an innovative suspended ion exchange process.

Science.gov (United States)

Metcalfe, David; Rockey, Chris; Jefferson, Bruce; Judd, Simon; Jarvis, Peter

2015-12-15

This investigation aimed to compare the disinfection by-product formation potentials (DBPFPs) of three UK surface waters (1 upland reservoir and 2 lowland rivers) with differing characteristics treated by (a) a full scale conventional process and (b) pilot scale processes using a novel suspended ion exchange (SIX) process and inline coagulation (ILCA) followed by ceramic membrane filtration (CMF). Liquid chromatography-organic carbon detection analysis highlighted clear differences between the organic fractions removed by coagulation and suspended ion exchange. Pretreatments which combined SIX and coagulation resulted in significant reductions in dissolved organic carbon (DOC), UV absorbance (UVA), trihalomethane and haloacetic acid formation potential (THMFP, HAAFP), in comparison with the SIX or coagulation process alone. Further experiments showed that in addition to greater overall DOC removal, the processes also reduced the concentration of brominated DBPs and selectively removed organic compounds with high DBPFP. The SIX/ILCA/CMF process resulted in additional removals of DOC, UVA, THMFP, HAAFP and brominated DBPs of 50, 62, 62, 62% and 47% respectively compared with conventional treatment. Copyright © 2015. Published by Elsevier Ltd.

Adsorption of phosphate in hydrocalumite-like layered double hydroxides: a comparison between memory effect and ion exchange processes

International Nuclear Information System (INIS)

Bernardo, M.P.; Moreira, F.K.V.; Ribeiro, C.

2016-01-01

Phosphorus is an essential element for agriculture, but the excessive use of this element has caused severe damages to the environment. Layered double hydroxide (LDHs) are excellent candidates to remove PO 4 3- anions through adsorption process. In this work, the phosphate adsorption on hydrocalumite-like (Ca-Al) LDHs was evaluated over the ion exchange and memory effect processes. X-ray diffraction measurements revealed formation of analogous crystalline phases from both process as the phosphate concentration was increased. However, the phosphate quantity adsorbed varied according to the process used. The ion exchange route is the most efficient process to remove phosphate from aqueous medium. (author)

Ion exchange technology assessment report

International Nuclear Information System (INIS)

Duhn, E.F.

1992-01-01

In the execution of its charter, the SRS Ion Exchange Technology Assessment Team has determined that ion exchange (IX) technology has evolved to the point where it should now be considered as a viable alternative to the SRS reference ITP/LW/PH process. The ion exchange media available today offer the ability to design ion exchange processing systems tailored to the unique physical and chemical properties of SRS soluble HLW's. The technical assessment of IX technology and its applicability to the processing of SRS soluble HLW has demonstrated that IX is unquestionably a viable technology. A task team was chartered to evaluate the technology of ion exchange and its potential for replacing the present In-Tank Precipitation and proposed Late Wash processes to remove Cs, Sr, and Pu from soluble salt solutions at the Savannah River Site. This report documents the ion exchange technology assessment and conclusions of the task team

Merging constitutional and motional covalent dynamics in reversible imine formation and exchange processes.

Science.gov (United States)

Kovaříček, Petr; Lehn, Jean-Marie

2012-06-06

The formation and exchange processes of imines of salicylaldehyde, pyridine-2-carboxaldehyde, and benzaldehyde have been studied, showing that the former has features of particular interest for dynamic covalent chemistry, displaying high efficiency and fast rates. The monoimines formed with aliphatic α,ω-diamines display an internal exchange process of self-transimination type, inducing a local motion of either "stepping-in-place" or "single-step" type by bond interchange, whose rate decreases rapidly with the distance of the terminal amino groups. Control of the speed of the process over a wide range may be achieved by substituents, solvent composition, and temperature. These monoimines also undergo intermolecular exchange, thus merging motional and constitutional covalent behavior within the same molecule. With polyamines, the monoimines formed execute internal motions that have been characterized by extensive one-dimensional, two-dimensional, and EXSY proton NMR studies. In particular, with linear polyamines, nondirectional displacement occurs by shifting of the aldehyde residue along the polyamine chain serving as molecular track. Imines thus behave as simple prototypes of systems displaying relative motions of molecular moieties, a subject of high current interest in the investigation of synthetic and biological molecular motors. The motional processes described are of dynamic covalent nature and take place without change in molecular constitution. They thus represent a category of dynamic covalent motions, resulting from reversible covalent bond formation and dissociation. They extend dynamic covalent chemistry into the area of molecular motions. A major further step will be to achieve control of directionality. The results reported here for imines open wide perspectives, together with other chemical groups, for the implementation of such features in multifunctional molecules toward the design of molecular devices presenting a complex combination of

Nuclear safety inspection in treatment process for SG heat exchange tubes deficiency of unit 1, TNPS

International Nuclear Information System (INIS)

Zhang Chunming; Song Chenxiu; Zhao Pengyu; Hou Wei

2006-01-01

This paper describes treatment process for SG heat exchange tubes deficiency of Unit 1, TNPS, nuclear safety inspection of Northern Regional Office during treatment process for deficiency and further inspection after deficiency had been treated. (authors)

Process for the production of heavy water by H2-methylamine isotopic exchange

International Nuclear Information System (INIS)

Briec, M.; Ravoire, J.; Rostaing, M.

1977-01-01

An isotopic exchange process for separating D 2 from H 2 is presented. The H 2 -monomethylamine system is studied on the laboratory scale (kinetics, H 2 solubility, thermal stability and solubility of the catalyst) and on the pilot plant scale (operating conditions and economics) [fr

Student eXchange Process Modelling and Implementation by Using an Integrated BMP-SOA Approach

Directory of Open Access Journals (Sweden)

Octavian DOSPINESCU

2018-01-01

Full Text Available One of the key processes of an open University Information System concerns managing the student exchange activities. In this paper we will try to address the challenges regarding modelling and implementation when integrating such a process by crossing different information systems. Our approach will leverage SOA architecture by using BPM in order to structure and build the service orchestration level.

Process for exchanging hydrogen isotopes between gaseous hydrogen and water

International Nuclear Information System (INIS)

Hindin, S.G.; Roberts, G.W.

1977-01-01

A process is described for exchanging isotopes (particularly tritium) between water and gaseous hydrogen. Isotope depleted gaseous hydrogen and water containing a hydrogen isotope are introduced into the vapour phase in a first reaction area. The steam and gaseous hydrogen are brought into contact with a supported metal catalyst in this area in a parallel flow at a temperature range of around 225 and 300 0 C. An effluent flow comprising a mixture of isotope enriched gaseous hydrogen and depleted steam is evacuated from this area and the steam condensed into liquid water [fr

Treatment of low-activity-level process wastewaters by continuous countercurrent ion exchange

International Nuclear Information System (INIS)

Hall, R.; Watson, J.S.; Robinson, S.M.

1990-01-01

A mobile pilot-scale continuous countercurrent ion-exchange (CCIX) system is being operated at the Oak Ridge National Laboratory (ORNL) for the treatment of wastewaters that contain predominantly calcium sodium, and magnesium bicarbonates and are slightly contaminated with 90 Sr and 137 Cs radioisotopes. A demonstration study is being conducted to evaluate the near-steady-state performance and feasibility of a pilot-scale CCIX column for the selective removal of strontium from wastewater. Test results show that the process removes strontium sufficiently from the wastewater to permit discharge while significantly reducing the volume of secondary waste generation. CCIX has the potential for effective use in several applications; however, it has not been frequently utilized by industries to date. The CCIX system could offer an economical alternative for decontamination of wastewaters containing trace amounts of contaminants prior to discharge into the environment. This paper discusses (a) application of the Thomas model for predicting breakthrough curves from ion exchange column tests, (b) methods for scaleup of experimental small-scale ion-exchange columns to industrial-scale columns, and (c) methods for predicting effluent compositions in a CCIX system. 20 refs., 6 figs., 2 tabs

Review of low pressure plasma processing of proton exchange membrane fuel cell electrocatalysts

OpenAIRE

Brault , Pascal

2016-01-01

Review article; International audience; The present review is describing recent advances in plasma deposition and treatment of low temperature proton exchange membrane fuel cells electrocatalysts. Interest of plasma processing for growth of platinum based, non-precious and metal free electrocatalysts is highlighted. Electrocatalysts properties are tentatively correlated to plasma parameters.

Study of proton polarization in charge exchange process on optically oriented sodium atoms

International Nuclear Information System (INIS)

Zelenskij, A.N.; Kokhanovskij, S.A.

1984-01-01

Using high-power adjustable dye lasers for electron spin orientation in a charge-exchange target enables to significantly increase the proton polarization efficiency. A device is described that permits to avoid growth of the polarized proton beam emittance in a charge-exchange process in a strong magnetic field. The devise main feature is the use of an intensive source of neutral hydrogen atoms and the presence of a helium additional charge-exchange target which actualy is a proton ''source''. The helium charge-exchange cell is placed in the same magnetic field of a solenoid where a cell with oriented sodium is placed, a polarized electron being captured by a proton in the latter cell. In this case the beam at the solenoid inlet and outlet is in a neutral state; emittance growth related to the effect of end magnetic fields is not observed. The device after all prouduces polarized protons, their polarization degree is measured and the effect of various factors on polarization degree is studied. The description of the laser source and laser system is given. Measurement results have shown the beam intensity of neutral 7 keV atoms which passed through a polarizer to be 2 mA. The proton current doesn't depend. On the beeld fin the region of chrge exchange for the 8 kGs magnetic field. The degree of sodium polarization was 80% and polarized proton current approximately 70 μA at a temperature of the polarized sodium cell corresponding to the density of sodium vapar approximately 3x10 13 at/cm 2

Retrofit of heat exchanger networks with pressure recovery of process streams at sub-ambient conditions

International Nuclear Information System (INIS)

Onishi, Viviani C.; Ravagnani, Mauro A.S.S.; Caballero, José A.

2015-01-01

Highlights: • New mathematical model for heat exchanger networks retrofit with pressure recovery. • Optimal heat and work integration applied to the retrofit of sub-ambient processes. • Streams pressure manipulation is used to enhance heat integration of the system. • Compressors and turbines can act on a coupling shaft and/or as stand-alone equipment. • Use of smaller amount of cold utilities, reducing significantly the operational costs. - Abstract: This paper presents a new mathematical programming model for the retrofit of heat exchanger networks (HENs), wherein the pressure recovery of process streams is conducted to enhance heat integration. Particularly applied to cryogenic processes, HENs retrofit with combined heat and work integration is mainly aimed at reducing the use of expensive cold services. The proposed multi-stage superstructure allows the increment of the existing heat transfer area, as well as the use of new equipment for both heat exchange and pressure manipulation. The pressure recovery of streams is carried out simultaneously with the HEN design, such that the process conditions (streams pressure and temperature) are variables of optimization. The mathematical model is formulated using generalized disjunctive programming (GDP) and is optimized via mixed-integer nonlinear programming (MINLP), through the minimization of the retrofit total annualized cost, considering the turbine and compressor coupling with a helper motor. Three case studies are performed to assess the accuracy of the developed approach, including a real industrial example related to liquefied natural gas (LNG) production. The results show that the pressure recovery of streams is efficient for energy savings and, consequently, for decreasing the HEN retrofit total cost especially in sub-ambient processes

Modelling and dynamics analysis of heat exchanger as a distributed parameter process

International Nuclear Information System (INIS)

Savic, B.; Debeljkovic, D.Lj.

2004-01-01

A non-linear and afterwards linearized mathematical model of fuel oil cooling chamber has been developed. This chamber is a part of a recuperative heat exchanger of a tube-in-tube type and of opposite-direction acting, set in a heavy oil fraction discharge tubing. The model is defined as a range of assumptions and simplifications from which energy balance equations under non-stationary operating conditions are derived. The model is in the form of a set of partial differential equations with constant coefficients. Using appropriate numerical simulation of the transfer function, the dynamic of this process has been shown in the form of appropriate transient process responses which quite well correspond to the real process behavior

Modelling and dynamics analysis of heat exchanger as a distributed parameter process

Energy Technology Data Exchange (ETDEWEB)

Savic, B.; Debeljkovic, D.Lj. [University of Belgrade, Department of Control Engineering, Belgrade (Yugoslavia)

2004-07-01

A non-linear and afterwards linearized mathematical model of fuel oil cooling chamber has been developed. This chamber is a part of a recuperative heat exchanger of a tube-in-tube type and of opposite-direction acting, set in a heavy oil fraction discharge tubing. The model is defined as a range of assumptions and simplifications from which energy balance equations under non-stationary operating conditions are derived. The model is in the form of a set of partial differential equations with constant coefficients. Using appropriate numerical simulation of the transfer function, the dynamic of this process has been shown in the form of appropriate transient process responses which quite well correspond to the real process behavior.

Research on Heat Exchange Process in Aircraft Air Conditioning System

Science.gov (United States)

Chichindaev, A. V.

2017-11-01

Using of heat-exchanger-condenser in the air conditioning system of the airplane Tu-204 (Boeing, Airbus, Superjet 100, MS-21, etc.) for cooling the compressed air by the cold air with negative temperature exiting the turbine results in a number of operational problems. Mainly it’s frosting of the heat exchange surface, which is the cause of live-section channels frosting, resistance increasing and airflow in the system decreasing. The purpose of this work is to analyse the known freeze-up-fighting methods for heat-exchanger-condenser, description of the features of anti-icing protection and offering solutions to this problem. For the problem of optimizing the design of heat exchangers in this work used generalized criterion that describes the ratio of thermal resistances of cold and hot sections, which include: the ratio of the initial values of heat transfer agents flow state; heat exchange surface finning coefficients; factors which describes the ratio of operating parameters and finning area. By controlling the ratio of the thermal resistances can be obtained the desired temperature of the heat exchange surface, which would prevent freezing. The work presents the results of a numerical study of the effect of different combinations of regime and geometrical factors changes on reduction of the heat-exchanger-condenser freezing surface area, including using of variable ratio of thermal resistances.

Selection of the process for the heavy water production using isotopic exchange amonia-hydrogen

International Nuclear Information System (INIS)

Guzman R, G.H.

1980-01-01

The utilization of the Petroleos Mexicanos ammonia plants for heavy water production by the isotopic exchange NH 3 -H 2 process is presented, in addition a description of the other heavy water production processes was presented. In the ammonia hydrogen process exist two possible alternatives for the operation of the system, one of them is to carry out the enrichment to the same temperature, the second consists in making the enrichment at two different temperatures (dual temperature process), an analysis was made to select the best alternative. The conclusion was that the best operation is the dual temperature process, which presents higher advantages according to the thermodynamics and engineering of the process. (author)

Novel simple process for tocopherols selective recovery from vegetable oils by adsorption and desorption with an anion-exchange resin.

Science.gov (United States)

Hiromori, Kousuke; Shibasaki-Kitakawa, Naomi; Nakashima, Kazunori; Yonemoto, Toshikuni

2016-03-01

A novel and simple low-temperature process was used to recover tocopherols from a deodorizer distillate, which is a by-product of edible oil refining. The process consists of three operations: the esterification of free fatty acids with a cation-exchange resin catalyst, the adsorption of tocopherols onto an anion-exchange resin, and tocopherol desorption from the resin. No degradation of tocopherols occurred during these processes. In the tocopherol-rich fraction, no impurities such as sterols or glycerides were present. These impurities are commonly found in the product of the conventional process. This novel process improves the overall recovery ratio and the mass fraction of the product (75.9% and 51.0wt%) compared with those in the conventional process (50% and 35wt%). Copyright © 2015 Elsevier Ltd. All rights reserved.

International technology exchange in support of the Defense Waste Processing Facility wasteform production

International Nuclear Information System (INIS)

Kitchen, B.G.

1989-01-01

The nearly completed Defense Waste Processing Facility (DWPF) is a Department of Energy (DOE) facility at the Savannah River Site that is designed to immobilize defense high level radioactive waste (HLW) by vitrification in borosilicate glass and containment in stainless steel canisters suitable for storage in the future DOE HLW repository. The DWPF is expected to start cold operation later this year (1990), and will be the first full scale vitrification facility operating in the United States, and the largest in the world. The DOE has been coordinating technology transfer and exchange on issues relating to HLW treatment and disposal through bi-lateral agreements with several nations. For the nearly fifteen years of the vitrification program at Savannah River Laboratory, over two hundred exchanges have been conducted with a dozen international agencies involving about five-hundred foreign national specialists. These international exchanges have been beneficial to the DOE's waste management efforts through confirmation of the choice of the waste form, enhanced understanding of melter operating phenomena, support for paths forward in political/regulatory arenas, confirmation of costs for waste form compliance programs, and establishing the need for enhancements of melter facility designs. This paper will compare designs and schedules of the international vitrification programs, and will discuss technical areas where the exchanges have provided data that have confirmed and aided US research and development efforts, impacted the design of the DWPF and guided the planning for regulatory interaction and product acceptance

Kinetic Behavior of Exchange-Driven Growth with Catalyzed-Birth Processes

Science.gov (United States)

Wang, Hai-Feng; Lin, Zhen-Quan; Kong, Xiang-Mu

2006-12-01

Two catalyzed-birth models of n-species (n>=2) aggregates with exchange-driven growth processes are proposed and compared. In the first one, the exchange reaction occurs between any two aggregates Amk and Amj of the same species with the rate kernels Km(k,j) = Kmkj (m = 1,2,...,n, n>=2), and aggregates of An species catalyze a monomer-birth of Al species (l = 1,2,...,n-1) with the catalysis rate kernel Jl(k,j) = Jlkjυ. The kinetic behaviors are investigated by means of the mean-field theory. We find that the evolution behavior of aggregate-size distribution alk(t) of Al species depends crucially on the value of the catalysis rate parameter υ: (i) alk(t) obeys the conventional scaling law in the case of υ0. In the second model, the mechanism of monomer-birth of An-species catalyzed by Al species is added on the basis of the first model, that is, the aggregates of Al and An species catalyze each other to cause monomer-birth. The kinetic behaviors of Al and An species are found to fall into two categories for the different υ: (i) growth obeying conventional scaling form with υ0.

Using solvent extraction to process nitrate anion exchange column effluents

International Nuclear Information System (INIS)

Yarbro, S.L.

1987-10-01

Octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO), a new organophosphorous extractant, and a new centrifugal mixer-settler both recently developed at Argonne were evaluated for their potential use in the recovery of actinides from nitrate anion exchange column effluents. The performance of the extractant was evaluated by measuring the extraction coefficient values as a function of acid and salt concentration. Additional performance parameters include extraction coefficient behavior as a function of the total metal concentration in the organic phase, and comparison of different stripping and organic scrubbing techniques. A simulated effluent stream was used to evaluate the performance of the centrifugal mixer-settlers by comparing experimental and calculated interstage concentration profiles. Both the CMPO extractant and the centrifugal mixer-settlers have potential for processing nitrate column effluents, particularly if the stripping behavior can be improved. Details of the proposed process are presented in the flowsheet and contactor design analyses

Using solvent extraction to process nitrate anion exchange column effluents

Energy Technology Data Exchange (ETDEWEB)

Yarbro, S.L.

1987-10-01

Octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO), a new organophosphorous extractant, and a new centrifugal mixer-settler both recently developed at Argonne were evaluated for their potential use in the recovery of actinides from nitrate anion exchange column effluents. The performance of the extractant was evaluated by measuring the extraction coefficient values as a function of acid and salt concentration. Additional performance parameters include extraction coefficient behavior as a function of the total metal concentration in the organic phase, and comparison of different stripping and organic scrubbing techniques. A simulated effluent stream was used to evaluate the performance of the centrifugal mixer-settlers by comparing experimental and calculated interstage concentration profiles. Both the CMPO extractant and the centrifugal mixer-settlers have potential for processing nitrate column effluents, particularly if the stripping behavior can be improved. Details of the proposed process are presented in the flowsheet and contactor design analyses.

Effects Of Thermal Exchange On Material Flow During Steel Thixoextrusion Process

International Nuclear Information System (INIS)

Becker, Eric; Gu Guochao; Langlois, Laurent; Bigot, Regis; Pesci, Raphael

2011-01-01

Semisolid processing is an innovative technology for near net-shape production of components, where the metallic alloys are processed in the semisolid state. Taking advantage of the thixotropic behavior of alloys in the semisolid state, significant progress has been made in semisolid processing. However, the consequences of such behavior on the flow during thixoforming are still not completely understood. To explore and better understand the influence of the different parameters on material flow during thixoextrusion process, thixoextrusion experiments were performed using the low carbon steel C38. The billet was partially melted at high solid fraction. Effects of various process parameters including the initial billet temperature, the temperature of die, the punch speed during process and the presence of a Ceraspray layer at the interface of tool and billet were investigated through experiments and simulation. After analyzing the results thus obtained, it was identified that the aforementioned parameters mainly affect thermal exchanges between die and part. The Ceraspray layer not only plays a lubricant role, but also acts as a thermal barrier at the interface of tool and billet. Furthermore, the thermal effects can affect the material flow which is composed of various distinct zones.

Optical methods to study the gas exchange processes in large diesel engines

Energy Technology Data Exchange (ETDEWEB)

Gros, S.; Hattar, C. [Wartsila Diesel International Oy, Vaasa (Finland); Hernberg, R.; Vattulainen, J. [Tampere Univ. of Technology, Tampere (Finland). Plasma Technology Lab.

1996-12-01

To be able to study the gas exchange processes in realistic conditions for a single cylinder of a large production-line-type diesel engine, a fast optical absorption spectroscopic method was developed. With this method line-of-sight UV-absorption of SO{sub 2} contained in the exhaust gas was measured as a function of time in the exhaust port area in a continuously fired medium speed diesel engine type Waertsilae 6L20. SO{sub 2} formed during the combustion from the fuel contained sulphur was used as a tracer to study the gas exchange as a function of time in the exhaust channel. In this case of a 4-stroke diesel engine by assuming a known concentration of SO{sub 2} in the exhaust gas after exhaust valve opening and before inlet and exhaust valve overlap period, the measured optical absorption was used to determine the gas density and further the instantaneous exhaust gas temperature during the exhaust cycle. (author)

Ion-exchange chromatographic protein refolding

NARCIS (Netherlands)

Freydell, E.; Wielen, van der L.; Eppink, M.H.M.; Ottens, M.

2010-01-01

The application of ion-exchange (IEX) chromatography to protein refolding (IExR) has been successfully proven, as supported by various studies using different model proteins, ion-exchange media and flow configurations. Ion-exchange refolding offers a relatively high degree of process

Two-dimensional exchange and nutation exchange nuclear quadrupole resonance spectroscopy

International Nuclear Information System (INIS)

Mackowiak, M.; Sinyavsky, N.; Velikite, N.; Nikolaev, D.

2002-01-01

A theoretical treatment of the 2D exchange NQR pulse sequence is presented and applied to a quantitative study of exchange processes in molecular crystals. It takes into account the off-resonance irradiation, which critically influences the spin dynamics. The response to the three-pulse sequence of a system of spins I=3/2 in zero applied field, experiencing electric quadrupole couplings, is analysed. The mixing dynamics by exchange and the expected cross-peak intensities as a function of the frequency offset have been derived. The theory is illustrated by a study of the optimization procedure, which is of crucial importance for the detection of the cross- and diagonal-peaks in a 2D-exchange spectrum. The systems investigated are hexachloroethane and tetrachloroethylene. They show threefold and twofold reorientational jumps about the carbon-carbon axis, respectively. A new method of direct determination of rotational angles based on two-dimensional nutation exchange NQR spectroscopy is proposed. The method involves the detection of exchange processes through NQR nutation spectra recorded after the mixing interval. The response of a system of spins I=3/2 to the three-pulse sequence with increasing pulse widths is analyzed. It is shown that the 2D-nutation exchange NQR spectrum exhibits characteristic ridges, which manifest the motional mechanism in a model-independent fashion. The angles through which the molecule rotates can be read directly from elliptical ridges in the 2D spectrum, which are also sensitive to the asymmetry parameter of the electric field gradient tensor. (orig.)

Process-based modelling of NH3 exchange with grazed grasslands

Science.gov (United States)

Móring, Andrea; Vieno, Massimo; Doherty, Ruth M.; Milford, Celia; Nemitz, Eiko; Twigg, Marsailidh M.; Horváth, László; Sutton, Mark A.

2017-09-01

In this study the GAG model, a process-based ammonia (NH3) emission model for urine patches, was extended and applied for the field scale. The new model (GAG_field) was tested over two modelling periods, for which micrometeorological NH3 flux data were available. Acknowledging uncertainties in the measurements, the model was able to simulate the main features of the observed fluxes. The temporal evolution of the simulated NH3 exchange flux was found to be dominated by NH3 emission from the urine patches, offset by simultaneous NH3 deposition to areas of the field not affected by urine. The simulations show how NH3 fluxes over a grazed field in a given day can be affected by urine patches deposited several days earlier, linked to the interaction of volatilization processes with soil pH dynamics. Sensitivity analysis showed that GAG_field was more sensitive to soil buffering capacity (β), field capacity (θfc) and permanent wilting point (θpwp) than the patch-scale model. The reason for these different sensitivities is dual. Firstly, the difference originates from the different scales. Secondly, the difference can be explained by the different initial soil pH and physical properties, which determine the maximum volume of urine that can be stored in the NH3 source layer. It was found that in the case of urine patches with a higher initial soil pH and higher initial soil water content, the sensitivity of NH3 exchange to β was stronger. Also, in the case of a higher initial soil water content, NH3 exchange was more sensitive to the changes in θfc and θpwp. The sensitivity analysis showed that the nitrogen content of urine (cN) is associated with high uncertainty in the simulated fluxes. However, model experiments based on cN values randomized from an estimated statistical distribution indicated that this uncertainty is considerably smaller in practice. Finally, GAG_field was tested with a constant soil pH of 7.5. The variation of NH3 fluxes simulated in this way

Separation of rate processes for isotopic exchange between hydrogen and liquid water in packed columns 10

International Nuclear Information System (INIS)

Butler, J.P.; Hartog, J. den; Goodale, J.W.; Rolston, J.H.

1977-01-01

Wetproofed platinum catalysts in packed columns promote isotopic exchange between counter-current streams of hydrogen saturated with water vapour and liquid water. The net rate of deuterium transfer from isotopically enriched hydrogen has been measured and separated into two rate processes involving the transfer of deuterium from hydrogen to water vapour and from water vapour to liquid. These are compared with independent measurements of the two rate processes to test the two-step successive exchange model for trickle bed reactors. The separated transfer rates are independent of bed height and characterize the deuterium concentrations of each stream along the length of the bed. The dependences of the transfer rates upon hydrogen and liquid flow, hydrogen pressure, platinum loading and the effect of dilution of the hydrophobic catalyst with inert hydrophilic packing are reported. The results indicate a third process may be important in the transfer of deuterium between hydrogen and liquid water. (author)

New insights into proton surface mobility processes in PEMFC catalysts using isotopic exchange methods.

Science.gov (United States)

Ferreira-Aparicio, Paloma

2009-09-01

The surface chemistry and the adsorption/desorption/exchange behavior of a proton-exchange membrane fuel cell catalyst are analyzed as a case study for the development of tailor-made support materials of enhanced performance and stability. By using H2, D2, and CO as probe molecules, the relevance of some surface functional groups of the catalyst support on several diffusion processes taking place during the adsorption is shown. Sulfonic groups associated with the vulcanized carbon black surface have been detected by means of spectroscopic techniques (X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy) and by analysis of the desorbed products during temperature-programmed desorption tests by mass spectrometry. Such hydrophilic species have been observed to favor proton surface mobility and exchange with Pt-adsorbed deuterium even in the presence of adsorbed CO. This behavior is relevant both for the proper characterization of these kinds of catalysts using adsorption probes and for the design of new surface-modified carbon supports, enabling alternative proton-transfer pathways throughout the catalytic layers toward the membrane.

Comparison between conventional heat exchanger performance and an heat pipes exchanger

International Nuclear Information System (INIS)

Souza, J.R.G. de; Rocha, N.R.

1989-01-01

The thermal performance of conventional compact heat exchanger and of exchanger with heat pipes are simulated using a digital computer, for equal volumes and the same process conditions. The comparative analysis is depicted in graphs that indicate which of the situations each equipment is more efficient. (author)

Role of interference of states of intermediate nuclei in exchange processes

International Nuclear Information System (INIS)

Belyaeva, T.L.; Zelenskaya, N.S.; Teplov, I.B.

1982-01-01

Role of interference of intermediate nucleus states for exchange processes in reactions with alpha particles on 11 B, 7 Li and 6 Li light nuclei was investigated when considering exactly the process dynamics in the method of distorted waves with a finite interaction radius. The process dynamics, in particular, the overlapping degree of wave functions of bound states and interaction potentials, affects considerably the reaction cross section in the rections with alpha particles on nuclei of 1p shell. If in the reaction selection rules permit the excitation of components of intermediate system states with maximum values of #betta# 1 and #betta# 2 orbital moments at the given N 1 and N 2 , the contribution of such components to the cross section will be determining. When components of intermediate system states with maximum #betta# 1 (or #betta# 2 ) are forbidden with selection rules, several intermediate states can have approximately similar overlapping integrals

Multiobjective heat exchanger network synthesis based on grouping of process streams

Energy Technology Data Exchange (ETDEWEB)

Laukkanen, T.P.

2012-06-15

Heat exchanger network synthesis (HENS) is an important process synthesis problem and different tools and methods have been presented to solve this synthesis problem. This is mainly due to its importance in achieving energy savings in industrial processes in a cost-efficient way. The problem is also hard to solve and has been proven NP-hard (Nondeterministic Polynomial-time) and hence it is not known if a computationally efficient (polynomial) algorithm to solve the problem exists. Thus methods that provide good approximate solutions with reasonable computational requirements are useful. The objective of this thesis is to present new HENS approaches that are able to generate good solutions for HENS problems in a computationally efficient way so that all the objectives of HENS are optimized simultaneously. The main approach in accomplishing this objective is by grouping process streams. This is done either on the basis of the fact that in reality the process streams belong to a specific group or these groups are artificially developed. In the latter approach the idea is to decompose the set of binary variables i.e., the variables that define the existence of heat exchanger matches, into two separate problems. In this way the number of different options to connect the streams decreases compared to the situation where no decomposition is present. This causes the solution time to decrease and provides options for solving larger HENS problems. In this work the multiobjective HENS problem is solved either with the traditional weighting method or with an interactive multiobjective optimization method. In the weighting method the weights are the annual costs of the different objectives. In the interactive multiobjective optimization method the Decision Maker (DM) controls the decision-making process by classifying the objectives at each iteration. This multiobjective approach provides the benefit of using interactive multiobjective optimization, so that it is possible to

Study of kinetics, equilibrium and isotope exchange in ion exchange systems Pt. 6

International Nuclear Information System (INIS)

Plicka, J.; Stamberg, K.; Cabicar, J.; Gosman, A.

1986-01-01

The description of kinetics of ion exchange in ternary system was based upon three Nernst-Planck equations, each of them describing the particle diffusion flux of a given counterion as an independent process. For experimental verification, the strongly acidic cation exchanger OSTION KS 08 the shallow-bed technique, and 0.2 mol x dm -3 aqueous nitrate solutions were chosen. The kinetics of ion exchange in the system of cations Na + - Mg 2+ - UO 2 2+ was studied. The values of diffusion coefficients obtained by evaluating of kinetics of isotope exchange and binary ion exchange were used for calculation. The comparison of calculated exchange rate curves with the experimental ones was made. It was found that the exchanging counterions were affected by each other. (author)

Development of a multi-functional reprocessing process based on ion-exchange method by using tertiary pyridine-type resin

International Nuclear Information System (INIS)

Koyama, Shin-ichi; Ozawa, Masaki; Suzuki, Tatsuya; Fujii, Yasuhiko

2006-01-01

A series of separation experiment was performed in order to study a multi-functional spent fuel reprocessing process based on ion-exchange technique. The tertiary pyridine-type anion-exchange resin was used in this experiment and the mixed oxide fuel highly irradiated in the experimental fast reactor ''JOYO'' was used as a reference spent fuel. As the result, 106 Ru + 125 Sb, 137 Cs + 155 Eu + 144 Ce, plutonium, americium and curium could be separated from the irradiated fuel by only three steps of ion-exchange. The decontamination factor of 137 Cs and trivalent lanthanides ( 155 Eu, 144 Ce) in the final americium product exceeded 3.9 x 10 4 and 1.0 x 10 5 , respectively. The decontamination factor for the mutual separation of 243 Cm and 241 Am was larger than 2.2 x 10 3 for the americium product and, moreover, the content of 137 Cs, trivalent lanthanides and 243 Cm included in 241 Am product did not exceed 2 ppm. These results prove that the proposed simplified separation process has a reality as a candidate for future reprocessing process based on the partitioning and transmutation concept. (author)

Controlled growth of gold nanoparticles in zeolite L via ion-exchange reactions and thermal reduction processes

KAUST Repository

Zeng, Shangjing; Ding, Shuang; Li, Shangyu; Wang, Runwei; Zhang, Zongtao

2014-01-01

The growth of gold nanoparticles in zeolite can be controlled using ion-exchange reactions and thermal reduction processes. We produce a number of different sizes of the gold nanoparticles with the particle size increasing with increased temperature

Tube with helical grooving for a heat exchanger and its manufacturing process

International Nuclear Information System (INIS)

Yampolsky, J.S.

1980-01-01

This claim broadly concerns heat transfer tubes for heat exchangers of the kind described in the main patent specification and, in particular, a heat transfer tube and a process for manufacturing it. This tube includes a strip of metal, the opposite sides of which extend to form a certain number of longitudinal grooves of specific profile and height. This strip is helically wound and the lateral edges are joined butt to butt so as to be leak tight to fluids [fr

Concept development of exchange liquid regeneration

International Nuclear Information System (INIS)

Mader, D.L.

1985-08-01

Concepts are described for regeneration of the intermediate liquid used for isotope exchange in indirect laser isotope separation processes where the laser operates on a process gas distinct from the feed stream. The specific case of regeneration of an exchange liquid consisting of water, sodium hydroxide, and dimethyl sulfoxide for a process to separate deuterium from hydrogen using laser irradiation of trifluoromethane gas is developed. A water feed stream is converted to steam which rises in a chemical process column where it redeuterates a descending flow of exchange liquid without causing significant changes in its chemical composition

O3 and NOx Exchange

NARCIS (Netherlands)

Loubet, B.; Castell, J.F.; Laville, P.; Personne, E.; Tuzet, A.; Ammann, C.; Emberson, L.; Ganzeveld, L.; Kowalski, A.S.; Merbold, L.; Stella, P.; Tuovinen, J.P.

2015-01-01

This discussion was based on the background document “Review on modelling atmosphere-biosphere exchange of Ozone and Nitrogen oxides”, which reviews the processes contributing to biosphere-atmosphere exchange of O3 and NOx, including stomatal and non-stomatal exchange of O3 and NO, NO2.

Process for the exchange of hydrogen isotopes using a catalyst packed bed assembly

International Nuclear Information System (INIS)

Butler, J.P.; den Hartog, J.; Molson, F.W.R.

1978-01-01

A process for the exchange of hydrogen isotopes between streams of gaseous hydrogen and liquid water is described, wherein the streams of liquid water and gaseous hydrogen are simultaneously brought into contact with one another and a catalyst packed bed assembly while at a temperature in the range 273 0 to 573 0 K. The catalyst packed bed assembly may be composed of discrete carrier bodies of e.g. ceramics, metals, fibrous materials or synthetic plastics with catalytically active metal crystallites selected from Group VIII of the Periodic Table, partially enclosed in and bonded to the carrier bodies by a water repellent, water vapor and hydrogen gas permeable, porous, polymeric material, and discrete packing bodies having an exterior surface which is substantially hydrophilic and relatively noncatalytically active with regard to hydrogen isotope exchange between hydrogen gas and water vapor to that of the catalyst bodies

Theoretical study of charge exchange, ionization and electron loss processes, relevant to controlled thermonuclear research

International Nuclear Information System (INIS)

Janev, R.

1981-03-01

The following processes have been studied: a) Single and double charge exchange in low, medium and high energy collisions of atoms with multiply charged ions; b) Excitation and ionization processes in low, medium and high energy collisions between multiply charged ions and atoms; c) Ion-ion recombination and ion-pair formation collision processes between hydrogen and alkali atoms (ions); d) Resonant and Auger processes in slow collisions of atomic particles with solid surfaces (including surfaces covered by a sub-monoatomic layer). Processes a) and b) are important for the ''impurity problem'' of magnetically confined tokamak plasmas, whereas processes c) and d) for the production and transport of intense neutral beams for plasma heating

Electrically switched cesium ion exchange

International Nuclear Information System (INIS)

Lilga, M.A.; Orth, R.J.; Sukamto, J.P.H.; Schwartz, D.T.; Haight, S.M.; Genders, J.D.

1997-04-01

Electrically Switched Ion Exchange (ESIX) is a separation technology being developed as an alternative to conventional ion exchange for removing radionuclides from high-level waste. The ESIX technology, which combines ion exchange and electrochemistry, is geared toward producing electroactive films that are highly selective, regenerable, and long lasting. During the process, ion uptake and elution are controlled directly by modulating the potential of an ion exchange film that has been electrochemically deposited onto a high surface area electrode. This method adds little sodium to the waste stream and minimizes the secondary wastes associated with traditional ion exchange techniques. Development of the ESIX process is well underway for cesium removal using ferrocyanides as the electroactive films. Films having selectivity for perrhenate (a pertechnetate surrogate) over nitrate also have been deposited and tested. A case study for the KE Basin on the Hanford Site was conducted based on the results of the development testing. Engineering design baseline parameters for film deposition, film regeneration, cesium loading, and cesium elution were used for developing a conceptual system. Order of magnitude cost estimates were developed to compare with conventional ion exchange. This case study demonstrated that KE Basin wastewater could be processed continuously with minimal secondary waste and reduced associated disposal costs, as well as lower capital and labor expenditures

General Top-Down Ion Exchange Process for the Growth of Epitaxial Chalcogenide Thin Films and Devices

KAUST Repository

Xia, Chuan; Li, Peng; Li, Jun; Jiang, Qiu; Zhang, Xixiang; Alshareef, Husam N.

2016-01-01

) epitaxial chalcogenide metallic and semiconducting films and (2) free-standing chalcogenide films and (3) completed in situ formation of atomically sharp heterojunctions by selective ion exchange. Epitaxial NiCo2S4 thin films prepared by our process show 115

Dehydrating process experiment on spent ion-exchange resin sludge by Funda Filter

International Nuclear Information System (INIS)

Hasegawa, Tatsuo; Ishino, Kazuyuki

1977-01-01

In nuclear power plants, Funda Filters are employed to dehydrate spent powdery ion-exchange resin sludge. The Funda Filter is very effective for eliminating small rust components contained in spent powdery resin slurry; however, in the drying process, the complete drying of spent powdery resin is very difficult because the filter cake of resin on the horizontal filter leaf is likely to crack and let out steam and hot air through the cracks. This paper deals with the results of experiments conducted to clarify the detailed phenomena of dehydration so the above problem could be solved. The above experiments were made on the precoating and drying of granular ion-exchange resin slurry that had not yet been put to practical use. The experiments were composed of one fundamental and one operational stage. In the fundamental experiment, the dehydration properties and dehydration mechanism of resins were made clear, and the most effective operational method was established through the operational experiments conducted using large-scale Funda Filter test equipment under various conditions. (auth.)

Surface Modification and Surface - Subsurface Exchange Processes on Europa

Science.gov (United States)

Phillips, C. B.; Molaro, J.; Hand, K. P.

2017-12-01

The surface of Jupiter's moon Europa is modified by exogenic processes such as sputtering, gardening, radiolysis, sulfur ion implantation, and thermal processing, as well as endogenic processes including tidal shaking, mass wasting, and the effects of subsurface tectonic and perhaps cryovolcanic activity. New materials are created or deposited on the surface (radiolysis, micrometeorite impacts, sulfur ion implantation, cryovolcanic plume deposits), modified in place (thermal segregation, sintering), transported either vertically or horizontally (sputtering, gardening, mass wasting, tectonic and cryovolcanic activity), or lost from Europa completely (sputtering, plumes, larger impacts). Some of these processes vary spatially, as visible in Europa's leading-trailing hemisphere brightness asymmetry. Endogenic geologic processes also vary spatially, depending on terrain type. The surface can be classified into general landform categories that include tectonic features (ridges, bands, cracks); disrupted "chaos-type" terrain (chaos blocks, matrix, domes, pits, spots); and impact craters (simple, complex, multi-ring). The spatial distribution of these terrain types is relatively random, with some differences in apex-antiapex cratering rates and latitudinal variation in chaos vs. tectonic features. In this work, we extrapolate surface processes and rates from the top meter of the surface in conjunction with global estimates of transport and resurfacing rates. We combine near-surface modification with an estimate of surface-subsurface (and vice versa) transport rates for various geologic terrains based on an average of proposed formation mechanisms, and a spatial distribution of each landform type over Europa's surface area. Understanding the rates and mass balance for each of these processes, as well as their spatial and temporal variability, allows us to estimate surface - subsurface exchange rates over the average surface age ( 50myr) of Europa. Quantifying the timescale

A PC-based system for simulation of processes in the isotopic exchange column of a cryogenic pilot plant

International Nuclear Information System (INIS)

Retevoi, Carmen Maria; Stefan, Liviu; Baltateanu, Ovidiu; Stefan, Iuliana

2001-01-01

The technology developed at the Institute of Cryogenics and Isotope Separations is based on catalytic isotope exchange between water and hydrogen gas both carrying various isotopes of hydrogen: normal hydrogen, deuterium, and tritium. This isotope exchange is followed by cryogenic distillation to separate the various isotopes of hydrogen gas. The detritiation process was simulated using water as working fluid, with a small content of deuterium and a gaseous mixture of hydrogen and deuterium. Isotopic separation of hydrogen is very important for nuclear plants utilizing the CANDU reactor concept. Tritiated water is extracted from the moderator of the reactor and the tritium is removed in order to reduce the radiation levels from the reactor. One of the most important steps in this process is the catalytic isotope exchange between tritiated water and hydrogen gas. In the 'Catalytic isotope exchange' system, tritium transfer occurs from the liquid phase (tritiated heavy water) into the gaseous phase (hydrogen) in an isotope exchange column. The column is packed with alternating layers of two types of catalysts: an ordered B7 type of phosphorous bronze to catalyze the equilibration between liquid and gaseous water and a PT/C/PTFE catalyst to catalyze the reaction between water vapor and hydrogen gas. The corresponding reactions are (DTO) L + (D 2 O) V ↔ (D 2 O) L + (DTO) V and (DTO) V + (D 2 ) G ↔ (D 2 O) V + (DT)G. The design of the process requires a constant catalytic exchange temperature that must be maintained at a value of 90 deg.C. To achieve this, the plant is equipped with electrical heat exchangers for heating the gas (hydrogen) and the heavy water. The control is achieved using an array of sensors and controllers. The sensors used for monitoring the process are type J thermocouples. The temperature control is achieved by controlling the electrical power fed to the heaters. Besides sensing the fluid temperatures at various points, we also monitor the

Computer-aided process planning in prismatic shape die components based on Standard for the Exchange of Product model data

Directory of Open Access Journals (Sweden)

Awais Ahmad Khan

2015-11-01

Full Text Available Insufficient technologies made good integration between the die components in design, process planning, and manufacturing impossible in the past few years. Nowadays, the advanced technologies based on Standard for the Exchange of Product model data are making it possible. This article discusses the three main steps for achieving the complete process planning for prismatic parts of the die components. These three steps are data extraction, feature recognition, and process planning. The proposed computer-aided process planning system works as part of an integrated system to cover the process planning of any prismatic part die component. The system is built using Visual Basic with EWDraw system for visualizing the Standard for the Exchange of Product model data file. The system works successfully and can cover any type of sheet metal die components. The case study discussed in this article is taken from a large design of progressive die.

One photon exchange processes and the calibration of polarization of high energy protons

International Nuclear Information System (INIS)

Margolis, B.; Thomas, G.H.

1978-01-01

Polarization phenomena in small momentum transfer high energy one-photon exchange processes in the reaction p + A → X + A where A is a complex nucleus and X is anything are examined. It is shown that these polarizations can be related directly to photoproduction polarization effects in the reaction γ + p → X at low energies. Explicit formulae are written for polarization effects in the case where X → π 0 + p

Apparatus for concentrating by dual temperature exchange

International Nuclear Information System (INIS)

Spevack, J.S.

1975-01-01

The dual temperature exchange apparatus, with a dual temperature stage having a hot processing tower and a cold processing tower, is provided with means for transferring heat from the hot processed gas to both liquid and gas being delivered to the hot processing tower. The heat exchange system provides means for effecting direct contact between the hot processed gas and the cold processed liquid being delivered to the hot tower, means for establishing a circulation of the resulting heated processed liquid, and means including an indirect contact exchanger for transferring heat from said circulation to condition the gas being supplied to the hot processing tower. The reactants in the example given are hydrogen sulfide gas and liquid water

A Widely-Accessible Distributed MEMS Processing Environment. The MEMS Exchange Program

Science.gov (United States)

2012-10-29

all of these patterns in advance, we made a new cost model, called the Python Code cost model, which utilizes the power of a high level programming ...document entitled “The Beginners Guide to MEMS Processing” on the MEMSNet and MEMS Exchange The MEMS Exchange Program Final Technical Report October 29...from the Government is absolutely necessary. As said The MEMS Exchange Program Final Technical Report October 29, 2012 Page 57 of 58 before

Ion exchange kinetics of alkaline earths on Zr(IV) arsenosilicate cation exchanger

International Nuclear Information System (INIS)

Varshney, K.G.; Agrawal, S.; Varshney, K.

1984-01-01

A new approach based on the Nernst-Planck equations was applied to study the ion exchange kinetics for the exchange reactions of Mg(II), Ca(II), Sr(II) and Ba(II) with H + -ions at various temperatures on the zirconium(IV) arsenosilicate phase. Under the conditions of particle diffusion, the rate of exchange was found to be independent of the metal ion concentration at and above 0.1 M in aqueous medium. Energy and entropy of activation were determined and found to vary linearly with the ionic radii and mobilities of alkaline earths, a unique feature observed for an inorganic ion exchanger. The results are useful for predicting the ion exchange processes occurring on the surface of an inorganic material of the type studied. (author)

Study of processes of interligand exchange between Cu(AA)2 and Y(DPM)3 in geseous phase

International Nuclear Information System (INIS)

Girichev, G.V.; Giricheva, N.I.; Belova, N.V.; Kuz'mina, N.P.; Kaul', A.R.; Gorbenko, O.Yu.

1993-01-01

Mass-spectrometric method was used to study the process, proceeding between gaseous copper acetylacetonate and yttrium dipivaloylmethanate in 150-630 deg C range. It was established that intensive ligand exchange with formation of Cu(DPM) (AA), Y(DPM) 2 (AA), Cu(DPM) 2 compounds in gaseous mixture took place between components. Thermal decomposition of copper and yttrium β-diketonates was observed with temperature growth, along with reactions of interligand exchange. Molecular forms of Y(DPM) 2 , Y(DPM)(AA), Cu(DPM) 2 and Cu(DPM)(AA) were the most thermally stable at that

Review of exchange processes on Ganymede in view of its planetary protection categorization.

Science.gov (United States)

Grasset, O; Bunce, E J; Coustenis, A; Dougherty, M K; Erd, C; Hussmann, H; Jaumann, R; Prieto-Ballesteros, O

2013-10-01

In this paper, we provide a detailed review of Ganymede's characteristics that are germane to any consideration of its planetary protection requirements. Ganymede is the largest moon in our solar system and is the subject of one of the main science objectives of the JUICE mission to the jovian system. We explore the probability of the occurrence of potentially habitable zones within Ganymede at present, including those both within the deep liquid ocean and those in shallow liquid reservoirs. We consider the possible exchange processes between the surface and any putative habitats to set some constraints on the planetary protection approach for this moon. As a conclusion, the "remote" versus "significant" chance of contamination will be discussed, according to our current understanding of this giant icy moon. Based on the different estimates we investigate here, it appears extremely unlikely that material would be exchanged downward through the upper icy layer of Ganymede and, thus, bring material into the ocean over timescales consistent with the survival of microorganisms.

Optimization of parameters of heat exchangers vehicles

Directory of Open Access Journals (Sweden)

Andrei MELEKHIN

2014-09-01

Full Text Available The relevance of the topic due to the decision of problems of the economy of resources in heating systems of vehicles. To solve this problem we have developed an integrated method of research, which allows to solve tasks on optimization of parameters of heat exchangers vehicles. This method decides multicriteria optimization problem with the program nonlinear optimization on the basis of software with the introduction of an array of temperatures obtained using thermography. The authors have developed a mathematical model of process of heat exchange in heat exchange surfaces of apparatuses with the solution of multicriteria optimization problem and check its adequacy to the experimental stand in the visualization of thermal fields, an optimal range of managed parameters influencing the process of heat exchange with minimal metal consumption and the maximum heat output fin heat exchanger, the regularities of heat exchange process with getting generalizing dependencies distribution of temperature on the heat-release surface of the heat exchanger vehicles, defined convergence of the results of research in the calculation on the basis of theoretical dependencies and solving mathematical model.

Contact isotopic- and contact ion-exchange between two adsorbents

International Nuclear Information System (INIS)

Bunzl, K.; Mohan, R.; Haimerl, M.

1975-01-01

The kinetics of contact ion exchange processes between an ion exchange membrane and resin ion exchange beads, stirred in pure water, was investigated. A general criterion was derived, which indicates whether diffusion of the ions between the intermingling electric double layers or the collision frequency between the two adsorbents is the rate dermining step. Since the latter process proved to be rate controlling under our experimental conditions, the corresponding rate equations were derived under various initial and boundary conditions. Experimentally, the kinetics of contact isotopic exchange of Cs + - and Na + -ions as well as of the reverse contact ion exchange process of Cs + -versus Na + -ions were investigated by using Na 22 and Cs 137 radioisotopes. The experiments reveal in quantitative accord with the theory that the rate of collision controlled contact ion exchange processes depends mainly on the 'exchange coefficient', the separation factor and the collision frequency. While the latter two quantities were determined independently by separate experiments, the 'exchange coefficient' was evaluated from a contact isotopic exchange experiment. (orig.) [de

Modeling of the Process of Three-Isotope (H, D, T) Exchange Between Hydrogen Gas and Water Vapour on Pt-SDBC Catalyst over a Wide Range of Deuterium Concentration

International Nuclear Information System (INIS)

Fedorchenko, O.A.; Alekseev, I.A.; Tchijov, A.S.; Uborsky, V.V.

2005-01-01

The large scale studies of Combined Electrolysis and Catalytic Exchange (CECE) process in Petersburg Nuclear Physics Institute showed a complicated influence of various factors on the process caused by the presence of two simultaneous isotope exchange sub processes: counter-current phase exchange (between liquid water and water vapour) and co-current catalytic exchange (between hydrogen gas and water vapour). A laboratory scale set-up of glass made apparatuses was established in such a way that it allows us to study phase and catalytic exchange apart. A computer model of the set-up has been developed.The catalytic isotope exchange model formulation is presented. A collection of reversible chemical reactions is accompanied by diffusion of the gaseous reactants and reaction products in the pores of catalyst carrier. This has some interesting features that are demonstrated. Thus it was noted that the flow rates ratio (gas to vapour - λ = G/V) as well as the concentrations of reactants exert influence on the process efficiency

Energy loss and charge exchange processes of high energy heavy ions channeled in crystals

International Nuclear Information System (INIS)

Poizat, J.C.; Andriamonje, S.; Anne, R.; Faria, N.V.d.C.; Chevallier, M.; Cohen, C.; Dural, J.; Farizon-Mazuy, B.; Gaillard, M.J.; Genre, R.; Hage-Ali, M.; Kirsch, R.; L'hoir, A.; Mory, J.; Moulin, J.; Quere, Y.; Remillieux, J.; Schmaus, D.; Toulemonde, M.

1990-01-01

The interaction of moving ions with single crystals is very sensitive to the orientation of the incident beam with respect to the crystalline directions of the target. Our experiments show that high energy heavy ion channeling deeply modifies their slowing down and charge exchange processes. This is due to the fact that channeled ions interact only with outershell target electrons, which means that the electron density they experience is very low and that the binding energy, and then the momentum distribution of these electrons, are quite different from the corresponding average values associated to random incidence. The two experimental studies presented here show the reduction of the energy loss rate for fast channeled heavy ions and illustrate the two aspects of channeling effects on charge exchange, the reduction of electron loss on one hand, and of electron capture on the other hand

Use of Anion Exchange Resins for One-Step Processing of Algae from Harvest to Biofuel

Directory of Open Access Journals (Sweden)

Martin Poenie

2012-07-01

Full Text Available Some microalgae are particularly attractive as a renewable feedstock for biodiesel production due to their rapid growth, high content of triacylglycerols, and ability to be grown on non-arable land. Unfortunately, obtaining oil from algae is currently cost prohibitive in part due to the need to pump and process large volumes of dilute algal suspensions. In an effort to circumvent this problem, we have explored the use of anion exchange resins for simplifying the processing of algae to biofuel. Anion exchange resins can bind and accumulate the algal cells out of suspension to form a dewatered concentrate. Treatment of the resin-bound algae with sulfuric acid/methanol elutes the algae and regenerates the resin while converting algal lipids to biodiesel. Hydrophobic polymers can remove biodiesel from the sulfuric acid/methanol, allowing the transesterification reagent to be reused. We show that in situ transesterification of algal lipids can efficiently convert algal lipids to fatty acid methyl esters while allowing the resin and transesterification reagent to be recycled numerous times without loss of effectiveness.

Mathematical simulation and calculation of the continuous countercurrent process of ion-exchange extraction of strontium from strongly mineralized solutions

International Nuclear Information System (INIS)

Nikashina, V.A.; Guryanova, L.N.; Baturova, L.L.; Venetsianov, E.V.; Ivanov, V.A.; Nikolaev, N.P.

1993-01-01

The program open-quotes Countercurrentclose quotes is developed for the simulation of a continuous ion-exchange extraction of strontium from strongly mineralized NaCl and CaCl 2 solutions using a KB-4 carboxylic cation-exchanger in the countercurrent columns. The program allows one to Calculate the conditions of Ca and Sr separation depending on the mode of operation at the sorption and regeneration stages, the residual Sr content on the overloaded sorbent, and the Sr separation on incompletely regenerated KB-4. It also makes it possible to find the optimal separation conditions. The program open-quotes Countercurrentclose quotes can be also used to simulate other ion-exchange processes

Treatment of low-activity-level process wastewaters by Continuous Countercurrent Ion Exchange

International Nuclear Information System (INIS)

Hall, R.; Watson, J.S.; Robinson, S.M.

1990-01-01

This paper discusses application of the Thomas model for predicting breakthrough curves from ion exchange column tests, methods for scale-up of experimental small-scaled ion exchange columns to industrial scale columns, and methods for predicting effluent compositions in a continuous countercurrent ion exchange system. 20 refs., 6 figs., 2 tabs

Capital dissipation minimization for a class of complex irreversible resource exchange processes

Science.gov (United States)

Xia, Shaojun; Chen, Lingen

2017-05-01

A model of a class of irreversible resource exchange processes (REPes) between a firm and a producer with commodity flow leakage from the producer to a competitive market is established in this paper. The REPes are assumed to obey the linear commodity transfer law (LCTL). Optimal price paths for capital dissipation minimization (CDM) (it can measure economic process irreversibility) are obtained. The averaged optimal control theory is used. The optimal REP strategy is also compared with other strategies, such as constant-firm-price operation and constant-commodity-flow operation, and effects of the amount of commodity transferred and the commodity flow leakage on the optimal REP strategy are also analyzed. The commodity prices of both the producer and the firm for the CDM of the REPes with commodity flow leakage change with the time exponentially.

Controlled growth of gold nanoparticles in zeolite L via ion-exchange reactions and thermal reduction processes

KAUST Repository

Zeng, Shangjing

2014-09-01

The growth of gold nanoparticles in zeolite can be controlled using ion-exchange reactions and thermal reduction processes. We produce a number of different sizes of the gold nanoparticles with the particle size increasing with increased temperature of the final heat treatment. © 2014 Elsevier B.V.

System for processing ion exchange resin regeneration waste liquid in atomic power plant

International Nuclear Information System (INIS)

Onaka, Noriyuki; Tanno, Kazuo; Shoji, Saburo.

1976-01-01

Object: To reduce the quantity of radioactive waste to be solidified by recovering and repeatedly using sulfuric acid and sodium hydroxide which constitute the ion exchange resin regeneration waste liquid. Structure: Cation exchange resin regeneration waste liquid is supplied to an anion exchange film electrolytic dialyzer for recovering sulfuric acid through separation from impurity cations, while at the same time anion exchange resin regeneration waste liquid is supplied to a cation exchange film electrolytic dialyzer for recovering sodium hydroxide through separation from impurity anions. The sulfuric acid and sodium hydroxide thus recovered are condensed by a thermal condenser and then, after density adjustment, repeatedly used for the regeneration of the ion exchange resin. (Aizawa, K.)

Exchange currents in nuclear physics

International Nuclear Information System (INIS)

Truglik, Eh.

1980-01-01

Starting from Adler's low-energy theorem for the soft pion production amplitudes the predictions of the meson exchange currents theory for the nuclear physics are discussed. The results are reformulated in terms of phenomenological lagrangians. This method allows one to pass naturally to the more realistic case of hard mesons. The predictions are critically compared with the existing experimental data. The main processes in which vector isovector exchange currents, vector isoscalar exchange currents and axial exchange currents take place are pointed out

Exchange bias in nearly perpendicularly coupled ferromagnetic/ferromagnetic system

International Nuclear Information System (INIS)

Bu, K.M.; Kwon, H.Y.; Oh, S.W.; Won, C.

2012-01-01

Exchange bias phenomena appear not only in ferromagnetic/antiferromagnetic systems but also in ferromagnetic/ferromagnetic systems in which two layers are nearly perpendicularly coupled. We investigated the origin of the symmetry-breaking mechanism and the relationship between the exchange bias and the system's energy parameters. We compared the results of computational Monte Carlo simulations with those of theoretical model calculation. We found that the exchange bias exhibited nonlinear behaviors, including sign reversal and singularities. These complicated behaviors were caused by two distinct magnetization processes depending on the interlayer coupling strength. The exchange bias reached a maximum at the transition between the two magnetization processes. - Highlights: ► Exchange bias phenomena are found in perpendicularly coupled F/F systems. ► Exchange bias exhibits nonlinear behaviors, including sign reversal and singularities. ► These complicated behaviors were caused by two distinct magnetization processes. ► Exchange bias reached a maximum at the transition between the two magnetization processes. ► We established an equation to maximize the exchange bias in perpendicularly coupled F/F system.

A counter-intuitive approach to calculating non-exchangeable 2H isotopic composition of hair: treating the molar exchange fraction fE as a process-related rather than compound-specific variable

Science.gov (United States)

Landwehr, J.M.; Meier-Augenstein, W.; Kemp, H.F.

2011-01-01

Hair is a keratinous tissue that incorporates hydrogen from material that an animal consumes but it is metabolically inert following synthesis. The stable hydrogen isotope composition of hair has been used in ecological studies to track migrations of mammals as well as for forensic and archaeological purposes to determine the provenance of human remains or the recent geographic life trajectory of living people. Measurement of the total hydrogen isotopic composition of a hair sample yields a composite value comprised of both metabolically informative, non-exchangeable hydrogen and exchangeable hydrogen, with the latter reflecting ambient or sample preparation conditions. Neither of these attributes is directly measurable, and the non-exchangeable hydrogen composition is obtained by estimation using a commonly applied mathematical expression incorporating sample measurements obtained from two distinct equilibration procedures. This commonly used approach treats the fraction of exchangeable hydrogen as a mixing ratio, with a minimal procedural fractionation factor assumed to be close or equal to 1. Instead, we propose to use full molar ratios to derive an expression for the non-exchangeable hydrogen composition explicitly as a function of both the procedural fractionation factor α and the molar hydrogen exchange fraction fE. We apply these derivations in a longitudinal study of a hair sample and demonstrate that the molar hydrogen exchange fraction fE should, like the procedural fractionation factor α, be treated as a process-dependent parameter, i.e. a reaction-specific constant. This is a counter-intuitive notion given that maximum theoretical values for the molar hydrogen exchange fraction fE can be calculated that are arguably protein-type specific and, as such, fE could be regarded as a compound-specific constant. We also make some additional suggestions for future approaches to determine the non-exchangeable hydrogen composition of hair and the use of

On-Line Ion Exchange Liquid Chromatography as a Process Analytical Technology for Monoclonal Antibody Characterization in Continuous Bioprocessing.

Science.gov (United States)

Patel, Bhumit A; Pinto, Nuno D S; Gospodarek, Adrian; Kilgore, Bruce; Goswami, Kudrat; Napoli, William N; Desai, Jayesh; Heo, Jun H; Panzera, Dominick; Pollard, David; Richardson, Daisy; Brower, Mark; Richardson, Douglas D

2017-11-07

Combining process analytical technology (PAT) with continuous production provides a powerful tool to observe and control monoclonal antibody (mAb) fermentation and purification processes. This work demonstrates on-line liquid chromatography (on-line LC) as a PAT tool for monitoring a continuous biologics process and forced degradation studies. Specifically, this work focused on ion exchange chromatography (IEX), which is a critical separation technique to detect charge variants. Product-related impurities, including charge variants, that impact function are classified as critical quality attributes (CQAs). First, we confirmed no significant differences were observed in the charge heterogeneity profile of a mAb through both at-line and on-line sampling and that the on-line method has the ability to rapidly detect changes in protein quality over time. The robustness and versatility of the PAT methods were tested by sampling from two purification locations in a continuous mAb process. The PAT IEX methods used with on-line LC were a weak cation exchange (WCX) separation and a newly developed shorter strong cation exchange (SCX) assay. Both methods provided similar results with the distribution of percent acidic, main, and basic species remaining unchanged over a 2 week period. Second, a forced degradation study showed an increase in acidic species and a decrease in basic species when sampled on-line over 7 days. These applications further strengthen the use of on-line LC to monitor CQAs of a mAb continuously with various PAT IEX analytical methods. Implementation of on-line IEX will enable faster decision making during process development and could potentially be applied to control in biomanufacturing.

The maximum power condition of the brayton cycle with heat exchange processes

International Nuclear Information System (INIS)

Jung, Pyung Suk; Cha, Jin Girl; Ro, Sung Tack

1985-01-01

The ideal brayton cycle has been analyzed with the heat exchange processes between the working fluid and the heat source and the sink while their heat capacity rates are constant. The power of the cycle can be expressed in terms of a temperature of the cycle and the heat capacity rate of the working fluid. There exists an optimum power condition where the heat capacity rate of the working fluid has a value between those of the heat source and the heat sink, and the cycle efficiency is determined by the inlet temperatures of the heat source and the sink. (Author)

Heat exchanger cleaning

International Nuclear Information System (INIS)

Gatewood, J.R.

1980-01-01

A survey covers the various types of heat-exchange equipment that is cleaned routinely in fossil-fired generating plants, the hydrocarbon-processing industry, pulp and paper mills, and other industries; the various types, sources, and adverse effects of deposits in heat-exchange equipment; some details of the actual procedures for high-pressure water jetting and chemical cleaning of some specific pieces of equipment, including nuclear steam generators. (DN)

Kinetic Behavior of Exchange-Driven Growth with Catalyzed-Birth Processes

International Nuclear Information System (INIS)

Wang Haifeng; Lin Zhenquan; Kong Xiangmu

2006-01-01

Two catalyzed-birth models of n-species (n≥2) aggregates with exchange-driven growth processes are proposed and compared. In the first one, the exchange reaction occurs between any two aggregates A m k and A m j of the same species with the rate kernels K m (k,j) = K m kj (m = 1,2,...,n, n≥2), and aggregates of A n species catalyze a monomer-birth of A l species (l = 1,2,...,n-1) with the catalysis rate kernel J l (k,j) = J l kj υ . The kinetic behaviors are investigated by means of the mean-field theory. We find that the evolution behavior of aggregate-size distribution a l k (t) of A l species depends crucially on the value of the catalysis rate parameter υ: (i) a l k (t) obeys the conventional scaling law in the case of υ≤0, (ii) a l k (t) satisfies a modified scaling form in the case of υ>0. In the second model, the mechanism of monomer-birth of A n -species catalyzed by A l species is added on the basis of the first model, that is, the aggregates of A l and A n species catalyze each other to cause monomer-birth. The kinetic behaviors of A l and A n species are found to fall into two categories for the different υ: (i) growth obeying conventional scaling form with υ≤0, (ii) gelling at finite time with υ>0.

Sediment exchange between groin fields and main-stream

Science.gov (United States)

Qin, Jie; Zhong, Deyu; Wu, Teng; Wu, Lingli

2017-10-01

Sediment exchange between groin fields and the main-stream influences the transport and distribution of polluted sediment that represents a hazard for rivers and neighboring floodplains. Despite its practical significance, little research has been done on the sediment exchange process itself, and existing studies used to estimate the sediment exchange by morphological change. The sediment exchange process, however, differs from morphological variation and includes two behaviors: the entrance of main-stream sediment into groin fields and the movement of groin field sediment out of groin fields. Therefore, this study aims at examining this exchange process and exploring the mechanisms of different exchange phenomena. Experiments were conducted in a mobile-bed laboratory flume by using a novel experimental method that successfully separates the movement of groin fields sediment from that of main-stream sediment. In addition to traditional measurements, such as measurements of morphological changes, surface flow velocities, and bed-form propagation, the deposition of main-stream sediment in groin fields is measured in detail. The results demonstrate that morphological change cannot reflect the sediment exchange process. The deposition of main-stream sediment in groin fields is determined by the dynamics of sediment movement, in which bedload- and suspended-sediment-dominated processes exhibit different deposition patterns. The movement of groin field sediment out of groin fields is determined mainly by local scouring around groins.

Nonlinear electron-phonon heat exchange

International Nuclear Information System (INIS)

Woods, L.M.; Mahan, G.D.

1998-01-01

A calculation of the energy exchange between phonons and electrons is done for a metal at very low temperatures. We consider the energy exchange due to two-phonon processes. Second-order processes are expected to be important at temperatures less than 1 K. We include two different second-order processes: (i) the Compton-like scattering of phonons, and (ii) the electron-dual-phonon scattering from the second-order electron-phonon interaction. It is found that the Compton-like process contains a singular energy denominator. The singularity is removed by introducing quasiparticle damping. For pure metals we find that the energy exchange depends upon the lifetime of the electrons and it is proportional to the temperature of the lattice as T L 8 . The same calculation is performed for the electron-dual-phonon scattering and it is found that the temperature dependence is T L 9 . The results can be applied to quantum dot refrigerators. copyright 1998 The American Physical Society

Cleaning Schedule Operations in Heat Exchanger Networks

Directory of Open Access Journals (Sweden)

Huda Hairul

2018-01-01

Full Text Available Heat exchanger networks have been known to be the essential parts in the chemical industries. Unfortunately, since the performance of heat exchanger can be decreasing in transferring the heat from hot stream into cold stream due to fouling, then cleaning the heat exchanger is needed to restore its initial performance periodically. A process of heating crude oil in a refinery plant was used as a case study. As many as eleven heat exchangers were used to heat crude oil before it was heated by a furnace to the temperature required to the crude unit distillation column. The purpose of this study is to determine the cleaning schedule of heat exchanger on the heat exchanger networks due to the decrease of the overall heat transfer coefficient by various percentage of the design value. A close study on the process of heat exchanger cleaning schedule in heat exchanger networks using the method of decreasing overall heat transfer coefficient as target. The result showed that the higher the fouling value the more often the heat exchanger is cleaned because the overall heat transfer coefficient decreases quickly.

Studies on indigenous ion exchange resins: alkali metal ions-hydrogen ion exchange equilibria

International Nuclear Information System (INIS)

Shankar, S.; Kumar, Surender; Venkataramani, B.

2001-01-01

With a view to select a suitable ion exchange resin for the removal of radionuclides (such as cesium, strontium etc.) from low level radioactive effluents, alkali metal ion -H' exchanges on nine indigenous gel- and macroporous-type and nuclear grade resins have been studied at a total ionic strength of 0.1 mol dm .3 (in the case ofCs' -H' exchange it was 0.05 mol dm .3 ). The expected theoretical capacities were not attained by all the resins for the alkali metal ions. The water content (moles/equiv.) of the fully swollen resins for different alkali metal ionic forms do not follow the usual sequence of greater the tendency of the cation to hydrate the higher the water uptake, but a reverse trend. The ion exchange isotherms (plots of equivalent fractions of the ion in resin phase, N M1 to that in solution, N M ) were not satisfactory and sorption of cations, for most of the resins, was possible only when the acidity of the solution was lowered. The variations of the selectivity coefficient, K, with N M show that the resins are highly cross linked and the selectivity sequence: Cs + >K + >Na + >Li + , obtained for all the resins indicate that hydrated ions were involved in the exchange process. However, the increase in the selectivity was not accompanied by the release of water, but unusual uptake of water, during the exchange process. The characteristics of macroporous resins were not significantly different from those of the gel-type resins. The results are discussed in terms of heterogeneity in the polymer net work, improper sulphonation process resulting in the formation of functional groups at inaccessible sites with weak acidic character and the overall lack of control in the preparation of different resins. (author)

Current issues and uncertainties in the measurement and modelling of air-vegetation exchange and within-plant processing of POPs

International Nuclear Information System (INIS)

Barber, Jonathan L.; Thomas, Gareth O.; Kerstiens, Gerhard; Jones, Kevin

2004-01-01

Air-vegetation exchange of POPs is an important process controlling the entry of POPs into terrestrial food chains, and may also have a significant effect on the global movement of these compounds. Many factors affect the air-vegetation transfer including: the physicochemical properties of the compounds of interest; environmental factors such as temperature, wind speed, humidity and light conditions; and plant characteristics such as functional type, leaf surface area, cuticular structure, and leaf longevity. The purpose of this review is to quantify the effects these differences might have on air/plant exchange of POPs, and to point out the major gaps in the knowledge of this subject that require further research. Uptake mechanisms are complicated, with the role of each factor in controlling partitioning, fate and behaviour process still not fully understood. Consequently, current models of air-vegetation exchange do not incorporate variability in these factors, with the exception of temperature. These models instead rely on using average values for a number of environmental factors (e.g. plant lipid content, surface area), ignoring the large variations in these values. The available models suggest that boundary layer conductance is of key importance in the uptake of POPs, although large uncertainties in the cuticular pathway prevents confirmation of this with any degree of certainty, and experimental data seems to show plant-side resistance to be important. Models are usually based on the assumption that POP uptake occurs through the lipophilic cuticle which covers aerial surfaces of plants. However, some authors have recently attached greater importance to the stomatal route of entry into the leaf for gas phase compounds. There is a need for greater mechanistic understanding of air-plant exchange and the 'scaling' of factors affecting it. The review also suggests a number of key variables that researchers should measure in their experiments to allow comparisons

TECHNICAL COMPARISON OF CANDIDATE ION EXCHANGE MEDIA FOR SMALL COLUMN ION EXCHANGE (SCIX) APPLICATIONS IN SUPPORT OF SUPPLEMENTAL LAW PRETREATMENT

International Nuclear Information System (INIS)

Ramsey, A.A.; Thorson, M.R.

2010-01-01

At-tank supplemental pretreatment including both filtration and small column ion exchange is currently under evaluation to facilitate salt waste retrieval and processing in the Hanford tank farms. Spherical resorcinol formaldehyde (sRF) resin is the baseline ion exchange resin for use in the Waste Treatment and Immobilization Plant (WTP). This document provides background and technical rationale to assist in determining whether spherical resorcinol formaldehyde (sRF) is also the appropriate ion exchange resin for supplemental LAW pretreatment processes and compares sRF with crystalline silicotitanate (CST) as potential supplemental pretreatment ion exchange media.

Minimizing Back Exchange in the Hydrogen Exchange-Mass Spectrometry Experiment

Science.gov (United States)

Walters, Benjamin T.; Ricciuti, Alec; Mayne, Leland; Englander, S. Walter

2012-12-01

The addition of mass spectrometry (MS) analysis to the hydrogen exchange (HX) proteolytic fragmentation experiment extends powerful HX methodology to the study of large biologically important proteins. A persistent problem is the degradation of HX information due to back exchange of deuterium label during the fragmentation-separation process needed to prepare samples for MS measurement. This paper reports a systematic analysis of the factors that influence back exchange (solution pH, ionic strength, desolvation temperature, LC column interaction, flow rates, system volume). The many peptides exhibit a range of back exchange due to intrinsic amino acid HX rate differences. Accordingly, large back exchange leads to large variability in D-recovery from one residue to another as well as one peptide to another that cannot be corrected for by reference to any single peptide-level measurement. The usual effort to limit back exchange by limiting LC time provides little gain. Shortening the LC elution gradient by 3-fold only reduced back exchange by ~2 %, while sacrificing S/N and peptide count. An unexpected dependence of back exchange on ionic strength as well as pH suggests a strategy in which solution conditions are changed during sample preparation. Higher salt should be used in the first stage of sample preparation (proteolysis and trapping) and lower salt (<20 mM) and pH in the second stage before electrospray injection. Adjustment of these and other factors together with recent advances in peptide fragment detection yields hundreds of peptide fragments with D-label recovery of 90 % ± 5 %.

Minimizing back exchange in the hydrogen exchange-mass spectrometry experiment.

Science.gov (United States)

Walters, Benjamin T; Ricciuti, Alec; Mayne, Leland; Englander, S Walter

2012-12-01

The addition of mass spectrometry (MS) analysis to the hydrogen exchange (HX) proteolytic fragmentation experiment extends powerful HX methodology to the study of large biologically important proteins. A persistent problem is the degradation of HX information due to back exchange of deuterium label during the fragmentation-separation process needed to prepare samples for MS measurement. This paper reports a systematic analysis of the factors that influence back exchange (solution pH, ionic strength, desolvation temperature, LC column interaction, flow rates, system volume). The many peptides exhibit a range of back exchange due to intrinsic amino acid HX rate differences. Accordingly, large back exchange leads to large variability in D-recovery from one residue to another as well as one peptide to another that cannot be corrected for by reference to any single peptide-level measurement. The usual effort to limit back exchange by limiting LC time provides little gain. Shortening the LC elution gradient by 3-fold only reduced back exchange by ~2%, while sacrificing S/N and peptide count. An unexpected dependence of back exchange on ionic strength as well as pH suggests a strategy in which solution conditions are changed during sample preparation. Higher salt should be used in the first stage of sample preparation (proteolysis and trapping) and lower salt (<20 mM) and pH in the second stage before electrospray injection. Adjustment of these and other factors together with recent advances in peptide fragment detection yields hundreds of peptide fragments with D-label recovery of 90% ± 5%.

Process for hydrogen isotope exchange and concentration between liquid water and hydrogen gas and catalyst assembly therefor

International Nuclear Information System (INIS)

Stevens, W.H.

1975-01-01

A bithermal, catalytic, hydrogen isotope exchange process between liquid water and hydrogen gas to effect concentration of the deuterium isotope of hydrogen is described. Liquid water and hydrogen gas are contacted with one another and with at least one catalytically active metal selected from Group VIII of the Periodic Table; the catalyst body has a water repellent, gas and water vapor permeable, organic polymer or resin coating, preferably a fluorinated olefin polymer or silicone resin coating, so that the isotope exchange takes place by two simultaneously occurring, and closely coupled in space, steps and concentration is effected by operating two interconnected sections containing catalyst at different temperatures. (U.S.)

Mathematical model development of heat and mass exchange processes in the outdoor swimming pool

OpenAIRE

M. V. Shaptala; D. E. Shaptala

2014-01-01

Purpose. Currently exploitation of outdoor swimming pools is often not cost-effective and, despite of their relevance, such pools are closed in large quantities. At this time there is no the whole mathematical model which would allow assessing qualitatively the effect of energy-saving measures. The aim of this work is to develop a mathematical model of heat and mass exchange processes for calculating basic heat and mass losses that occur during its exploitation. Methodology. The m...

Dehydriding Process and Hydrogen–Deuterium Exchange of LiBH4–Mg2FeD6 Composites

Directory of Open Access Journals (Sweden)

Guanqiao Li

2015-06-01

Full Text Available The dehydriding process and hydrogen–deuterium exchange (H–D exchange of xLiBH4 + (1 − xMg2FeD6 (x = 0.25, 0.75 composites has been studied in detail. For the composition with x = 0.25, only one overlapping mass peak of all hydrogen and deuterium related species was observed in mass spectrometry. This implied the simultaneous dehydriding of LiBH4 and Mg2FeD6, despite an almost 190 °C difference in the dehydriding temperatures of the respective discrete complex hydrides. In situ infrared spectroscopy measurements indicated that H–D exchange between [BH4]− and [FeD6]4− had occurred during ball-milling and was promoted upon heating. The extent of H–D exchange was estimated from the areas of the relevant mass signals: immediately prior to the dehydriding, more than two H atoms in [BH4]− was replaced by D atoms. For x = 0.75, H–D exchange also occurred and about one to two H atoms in [BH4]− was replaced by D atoms immediately before the dehydriding. In contrast to the situation for x = 0.25, firstly LiBH4 and Mg2FeD6 dehydrided simultaneously with a special molar ratio = 1:1 at x = 0.75, and then the remaining LiBH4 reacted with the Mg and Fe derived from the dehydriding of Mg2FeD6.

Quantum-CEP processing spent ion exchange resins from nuclear power stations

International Nuclear Information System (INIS)

Kaczmarsky, Myron

1997-01-01

Quantum-CEP (Q-CEP) is an innovative and proprietary technology developed by Molten Metal Technology, Inc, which can process radioactive and mixed waste streams to decontaminate and recover resources of commercial value while achieving significant volume reduction and radionuclide stabilization. A Q-CEP facility, located in Oak Ridge, Tennessee, processes low-level radioactive spent ion exchange resins (IER) from U.S commercial nuclear power plants. The first campaign processing low level radioactive spent IER was successfully completed in December 1996. Other milestones, since December, include operating parallel Trains A and B simultaneously and processing 25,000 lb. dry resin (50,000 lb. wet resin) or six equivalent High Integrity Containers (HICs) in one batch campaign, in March; and processing 50,000 lb. dry resin or 12 equivalent HICs in one batch campaign in May. This paper presents results from the March campaign (97-008) in which 25,000 lb. of dry spent IER from five nuclear power stations were processed. This campaign has been selected since it is representative of campaigns completed during the first five months of operation. Key highlights for this campaign include processing six HICs in batch campaign while achieving a volume reduction of 24: 1. Key performance targets for the facility are to process an average of six HICs per campaign batch and achieve a volume reduction of 30: 1. The average batch size and other performance parameters have steadily improved during the initial operating period with radioactive resin. The progress was dramatically demonstrated by the May campaign during which 12 HICs were processed - achieving a volume reduction estimated to exceed 50: 1. The campaigns in March and May demonstrate that the facility's design and technology are capable of achieving and even exceeding the facility's key target performance parameters

An improved, computer-based, on-line gamma monitor for plutonium anion exchange process control

International Nuclear Information System (INIS)

Pope, N.G.; Marsh, S.F.

1987-06-01

An improved, low-cost, computer-based system has replaced a previously developed on-line gamma monitor. Both instruments continuously profile uranium, plutonium, and americium in the nitrate anion exchange process used to recover and purify plutonium at the Los Alamos Plutonium Facility. The latest system incorporates a personal computer that provides full-feature multichannel analyzer (MCA) capabilities by means of a single-slot, plug-in integrated circuit board. In addition to controlling all MCA functions, the computer program continuously corrects for gain shift and performs all other data processing functions. This Plutonium Recovery Operations Gamma Ray Energy Spectrometer System (PROGRESS) provides on-line process operational data essential for efficient operation. By identifying abnormal conditions in real time, it allows operators to take corrective actions promptly. The decision-making capability of the computer will be of increasing value as we implement automated process-control functions in the future. 4 refs., 6 figs

Muonium spin exchange as a Poisson process: magnetic field dependence in transverse fields

International Nuclear Information System (INIS)

Senba, Masayoshi; British Columbia Univ., Vancouver, BC

1993-01-01

The muonium spin exchange has been investigated as a function of transverse magnetic field strength, where the Poisson nature of collisions is exploited to simplify the calculation. In intermediate fields where the so-called two-frequency muonium signal is observed, the muonium relaxation due to spin exchange is 1.5 times faster than in low fields. In even higher fields, the observed relaxation rate drops back to the low field value. Since the relaxation rate due to a chemical reaction is field independent, such a distinct field dependence in spin exchange can be used in distinguishing experimentally spin exchange from chemical reactions. The time evolution of the muon spin polarization in the presence of muonium spin exchange has been expressed in a simple analytical closed form. (author)

Global Concept of Financial Institutional Transformation of Stock Exchange

Directory of Open Access Journals (Sweden)

Burmaka Mykola

2017-12-01

Full Text Available The article is about the research of processes of global transformation of stock exchanges through the mechanisms of internationalization, corporate and network consolidation, and technology. Objective processes of internationalization in stock markets affected by financial globalization and arising global information resources create new challenges for stock exchanges that can be overcome by adequate development strategies. The growing competition between stock exchanges and new capital institutes requires stock exchanges to use modern exchange technologies, primarily innovative, in order to maintain liquidity and increase investment attractiveness. Have been analysed the newest tendencies and determinants of modern global financial institutional architecture construction, the leading role in which are starting to play new stock exchanges and stalk exchange platforms, formed in growing financial centres of the world. Have been identified he main components of international stock market restructurization in the process of financial globalization, one of the attributes of which turned out to be a certain fragmentation of markets and their universalization. Through the example of US and EU financial market modernization processes of the last decade have been analysed financial and legal mechanisms of the national and regional levels, which are designed to ensure sustainable development of the global economy at the postcrisis stage. Have been diagnosed international activity of stock exchanges through the quantity indexed of foreign companies in listing, volume of trade with foreign financial instruments, and participation of foreign investors in exchange trade. Have been offered and calculated indices of internationalization of the world’s leading stock market. Have been analysed consolidation processes of the leading stock exchanges and new electronic trading systems at the regional, meso-global and global levels, which resulted in formation of

Process for the exchange of hydrogen isotopes between streams of liquid water and gaseous halohydrocarbon and an apparatus therefor

International Nuclear Information System (INIS)

Symons, E.A.; Rolston, J.H.; Clermont, M.J.; Paterson, L.M.

1983-01-01

This invention provides a process for the exchange of hydrogen isotopes between streams of liquid water and gaseous halohydrocarbons comprising: (a) bringing into contact a water stream, a halohydrocarbon stream, and a catalytic porous anion exchange resin so that the isotope-deficient halohydrocarbon stream is enriched; (b) decomposing the halohydrocarbon stream photolytically into two gaseous streams, one enriched and the other deficient; (c) removing as a product the first, enriched stream; and (d) recycling the second stream for enrichment. An apparatus is also provided

Water-hydrogen isotope exchange process analysis

International Nuclear Information System (INIS)

Fedorchenko, O.; Alekseev, I.; Uborsky, V.

2008-01-01

The use of a numerical method is needed to find a solution to the equation system describing a general case of heterogeneous isotope exchange between gaseous hydrogen and liquid water in a column. A computer model of the column merely outputting the isotope compositions in the flows leaving the column, like the experimental column itself, is a 'black box' to a certain extent: the solution is not transparent and occasionally not fully comprehended. The approximate analytical solution was derived from the ZXY-diagram (McCabe-Thiele diagram), which illustrates the solution of the renewed computer model called 'EVIO-4.2' Several 'unusual' results and dependences have been analyzed and explained. (authors)

Measuring gas temperature during spin-exchange optical pumping process

Science.gov (United States)

Normand, E.; Jiang, C. Y.; Brown, D. R.; Robertson, L.; Crow, L.; Tong, X.

2016-04-01

The gas temperature inside a Spin-Exchange Optical Pumping (SEOP) laser-pumping polarized 3He cell has long been a mystery. Different experimental methods were employed to measure this temperature but all were based on either modelling or indirect measurement. To date there has not been any direct experimental measurement of this quantity. Here we present the first direct measurement using neutron transmission to accurately determine the number density of 3He, the temperature is obtained using the ideal gas law. Our result showed a surprisingly high gas temperature of 380°C, compared to the 245°C of the 3He cell wall temperature and 178°C of the optical pumping oven temperature. This experiment result may be used to further investigate the unsolved puzzle of the "X-factor" in the SEOP process which places an upper bound to the 3He polarization that can be achieved. Additional spin relaxation mechanisms might exist due to the high gas temperature, which could explain the origin of the X-factor.

Heat exchanger restart evaluation

International Nuclear Information System (INIS)

Morrison, J.M.; Hirst, C.W.; Lentz, T.F.

1992-01-01

On December 24, 1991, the K-Reactor was in the shutdown mode with full AC process water flow and full cooling water flow. Safety rod testing was being performed as part of the power ascension testing program. The results of cooling water samples indicated tritium concentrations higher than allowable. Further sampling and testing confirmed a Process Water System to Cooling Water System leak in heat exchanger 4A (HX 4A). The heat exchanger was isolated and the plant shutdown. Heat exchanger 4kA was removed from the plant and moved to C-Area prior to performing examinations and diagnostic testing. This included locating and identifying the leaking tube or tubes, eddy current examination of the leaking tube and a number of adjacent tubes, visually inspecting the leaking tube from both the inside as well as the area surrounding the failure mechanism. In addition ten other tubes that either exhibited eddy current indications or would represent a baseline condition were removed from heat exchanger 4A for metallurgical examination. Additional analysis and review of heat exchanger leakage history was performed to determine if there are any patterns which can be used for predictive purposes. Compensatory actions have been taken to improve the sensitivity and response time to any future events of this type. The results of these actions are summarized herein

Shell-and-tube heat exchanger selection aid

International Nuclear Information System (INIS)

Lupton, L.R.; Basso, R.A.J.

1989-11-01

A prototype has been developed to investigate the feasibility of using expert systems to aid junior process system designers with the selection of components for shell-and-tube heat exchangers. The selection criteria for heat exchanger design were based on process, environmental and administrative constraints. The system was developed using EXSYS and consists of approximately 140 rules. This paper describes the development process and the lessons learned

Chapter 11. Heat Exchangers

Energy Technology Data Exchange (ETDEWEB)

Rafferty, Kevin D.; Culver, Gene

1998-01-01

Most geothermal fluids, because of their elevated temperature, contain a variety of dissolved chemicals. These chemicals are frequently corrosive toward standard materials of construction. As a result, it is advisable in most cases to isolate the geothermal fluid from the process to which heat is being transferred. The task of heat transfer from the geothermal fluid to a closed process loop is most often handled by a plate heat exchanger. The two most common types used in geothermal applications are: bolted and brazed. For smaller systems, in geothermal resource areas of a specific character, downhole heat exchangers (DHEs) provide a unique means of heat extraction. These devices eliminate the requirement for physical removal of fluid from the well. For this reason, DHE-based systems avoid entirely the environmental and practical problems associated with fluid disposal. Shell and tube heat exchangers play only a minor role in low-temperature, direct-use systems. These units have been in common use in industrial applications for many years and, as a result, are well understood. For these reasons, shell and tube heat exchangers will not be covered in this chapter.

Noninvasive mapping of water diffusional exchange in the human brain using filter-exchange imaging.

Science.gov (United States)

Nilsson, Markus; Lätt, Jimmy; van Westen, Danielle; Brockstedt, Sara; Lasič, Samo; Ståhlberg, Freddy; Topgaard, Daniel

2013-06-01

We present the first in vivo application of the filter-exchange imaging protocol for diffusion MRI. The protocol allows noninvasive mapping of the rate of water exchange between microenvironments with different self-diffusivities, such as the intracellular and extracellular spaces in tissue. Since diffusional water exchange across the cell membrane is a fundamental process in human physiology and pathophysiology, clinically feasible and noninvasive imaging of the water exchange rate would offer new means to diagnose disease and monitor treatment response in conditions such as cancer and edema. The in vivo use of filter-exchange imaging was demonstrated by studying the brain of five healthy volunteers and one intracranial tumor (meningioma). Apparent exchange rates in white matter range from 0.8±0.08 s(-1) in the internal capsule, to 1.6±0.11 s(-1) for frontal white matter, indicating that low values are associated with high myelination. Solid tumor displayed values of up to 2.9±0.8 s(-1). In white matter, the apparent exchange rate values suggest intra-axonal exchange times in the order of seconds, confirming the slow exchange assumption in the analysis of diffusion MRI data. We propose that filter-exchange imaging could be used clinically to map the water exchange rate in pathologies. Filter-exchange imaging may also be valuable for evaluating novel therapies targeting the function of aquaporins. Copyright © 2012 Wiley Periodicals, Inc.

Processing of indium (III solutions via ion exchange with Lewatit K-2621 resin

Directory of Open Access Journals (Sweden)

López Díaz-Pavón, Adrián

2014-06-01

Full Text Available The processing of indium(III-hydrochloric acid solutions by the cationic ion exchange Lewatit K-2621 resin has been investigated. The influence of several variables such as the hydrochloric acid and metal concentrations in the aqueous solution and the variation of the amount of resin added has been studied. Moreover, a kinetic study performed in the uptake of indium(III by Lewatit K-2621, shows that either the film-diffusion and the particle-diffusion models fit the ion exchange process onto the resin, depending upon the initial metal concentration in the aqueous solution. The loaded resin could be eluted by HCl solutions at 20 °C.Se ha investigado el tratamiento de disoluciones de ácido clorhídrico conteniendo indio(III mediante la resina de cambio catiónico Lewatit K-2621. Las variables ensayadas han sido las concentraciones de ácido y de metal en la disolución acuosa y la cantidad de resina empleada en el tratamiento de dichas disoluciones. Asimismo, se ha llevado a cabo un estudio cinético del proceso de intercambio catiónico entre el indio(III y la resina Lewatit K-2621. Este estudio muestra que el proceso de intercambio responde a un mecanismo de difusión en la disolución o en la partícula de resina dependiendo de la concentración inicial del metal en el medio acuoso. El metal cargado en la resina puede ser eluido con disoluciones de ácido clorhídrico a 20 °C.

Innovative heat exchangers

CERN Document Server

Scholl, Stephan

2018-01-01

This accessible book presents unconventional technologies in heat exchanger design that have the capacity to provide solutions to major concerns within the process and power-generating industries. Demonstrating the advantages and limits of these innovative heat exchangers, it also discusses micro- and nanostructure surfaces and micro-scale equipment, and introduces pillow-plate, helical and expanded metal baffle concepts. It offers step-by-step worked examples, which provide instructions for developing an initial configuration and are supported by clear, detailed drawings and pictures. Various types of heat exchangers are available, and they are widely used in all fields of industry for cooling or heating purposes, including in combustion engines. The market in 2012 was estimated to be U$ 42.7 billion and the global demand for heat exchangers is experiencing an annual growth of about 7.8 %. The market value is expected to reach U$ 57.9 billion in 2016, and approach U$ 78.16 billion in 2020. Providing a valua...

Advantages of chemical exchange-sensitive spin-lock (CESL) over chemical exchange saturation transfer (CEST) for hydroxyl- and amine-water proton exchange studies.

Science.gov (United States)

Jin, Tao; Kim, Seong-Gi

2014-11-01

The chemical exchange (CE) rate of endogenous hydroxyl and amine protons with water is often comparable to the difference in their chemical shifts. These intermediate exchange processes have been imaged by the CE saturation transfer (CEST) approach with low-power and long-duration irradiation. However, the sensitivity is not optimal and, more importantly, the signal is contaminated by slow magnetization transfer processes. Here, the properties of CEST signals are compared with those of a CE-sensitive spin-lock (CESL) technique irradiating at the labile proton frequency. First, using a higher power and shorter irradiation in CE-MRI, we obtain: (i) an increased selectivity to faster CE rates via a higher sensitivity to faster CEs and a lower sensitivity to slower CEs and magnetization transfer processes; and (ii) a decreased in vivo asymmetric magnetization transfer contrast measured at ±15 ppm. The sensitivity gain of CESL over CEST is higher for a higher power and shorter irradiation. Unlike CESL, CEST signals oscillate at a very high power and short irradiation. Second, time-dependent CEST and CESL signals are well modeled by analytical solutions of CE-MRI with an asymmetric population approximation, which can be used for quantitative CE-MRI and validated by simulations of Bloch-McConnell equations and phantom experiments. Finally, the in vivo amine-water proton exchange contrast measured at 2.5 ppm with ω1 = 500 Hz is 18% higher in sensitivity for CESL than CEST at 9.4 T. Overall, CESL provides better exchange rate selectivity and sensitivity than CEST; therefore, CESL is more suitable for CE-MRI of intermediate exchange protons. Copyright © 2014 John Wiley & Sons, Ltd.

Electrodialytic decontamination of spent ion exchange resins

International Nuclear Information System (INIS)

Nott, B.R.

1982-01-01

Development of a novel electrodialytic decontamination process for the selective removal of radioactive Cs from spent ion exchange resins containing large amounts of Li is described. The process involves passage of a dc electric current through a bed of the spent ion exchange resin in a specially designed electrodialytic cell. The radiocesium so removed from a volume of the spent resin is concentrated onto a much smaller volume of a Cs selective sorbent to achieve a significant radioactive waste volume reduction. Technical feasibility of the electrodialytic resin decontamination process has been demonstrated on a bench scale with a batch of simulated spent ion exchange resin and using potassium cobalt ferrocyanide as the Cs selective sorbent. A volume reduction factor between 10 and 17 has been estimated. The process appears to be economically attractive. Improvements in process economics can be expected from optimization of the process. Other possible applications of the EDRD process have been identified

Data Exchange Protocol in Repsail

Directory of Open Access Journals (Sweden)

Gucma Maciej

2017-12-01

Full Text Available Article presents implantation and theoretical considerations of data exchange protocol developed for the RepSail project, where main objective was design and building innovative hybrid yacht. One of problems during the design process was improper functioning of data exchange protocols that were available in the commercially available devices to mention navigation purpose NMEA183 or 2000 as well as automation dedicated ones (CAN and similar. Author shows the basis of the dedicated format of exchange for in board devices.

Disposal of bead ion exchange resin wastes

International Nuclear Information System (INIS)

Gay, R.L.; Granthan, L.F.

1985-01-01

Bead ion exchange resin wastes are disposed of by a process which involves spray-drying a bead ion exchange resin waste in order to remove substantially all of the water present in such waste, including the water on the surface of the ion exchange resin beads and the water inside the ion exchange resin beads. The resulting dried ion exchange resin beads can then be solidified in a suitable solid matrix-forming material, such as a polymer, which solidifies to contain the dried ion exchange resin beads in a solid monolith suitable for disposal by burial or other conventional means

High temperature heat exchanger application in power engineering and energy-technological processes

International Nuclear Information System (INIS)

Shpilrain, E.E.

1986-01-01

The possibilities for intensification of various processes in metallurgy and chemical technology, the prospects for enhancing power plant efficiency are often linked with temperature increase of reagents, heat carriers and working fluids. In some cases elevated temperatures give the opportunity to use new and principally different technologies, enhance capacities of power production units and technological apparatuses, improve their economical performance. The variety of problems where high temperature heat exchangers are or can be used are extremely wide. It is therefore impossible to overview all of them in one lecture. Therefore the author tries to consider only some examples which are typical and gives an impression of what kind of problems arise in these cases

Flexible Exchange of Farming Device Data

DEFF Research Database (Denmark)

Iftikhar, Nadeem; Pedersen, Torben Bach

2011-01-01

A new trend in the farming business is to replace conventional farming devices with computerized farming devices. Accordingly, numerous computer-based farming devices for logging, processing and exchanging data have recently been installed on moving farm machinery such as tractors. The exchange o......-directional data exchange as well as efficient requirements change management through a graphical user interface. The paper also demonstrates the use of the proposed solution based on a farming case study and open source technologies....... and systems to exchange data based on a predefined set of rules. In consequence, many hand-coded data exchange solutions have been developed in the farming business. Although efforts regarding incorporating data exchange standards have been made, their actual usage so far has been limited, due to the fact...

Advances in processing technologies for titanium heat exchanger tubes of fossil and nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Likhareva, T P; Tchizhik, A A; Chavchanidze, N N [Polzanov Central Boiler and Turbine Institute, St. Petersburg (Russian Federation)

1999-12-31

The advances in processing technologies for titanium heat exchangers with rolled and welded tubes of fossil and nuclear power plants in Russia are presented. The special methodology of investigations with constant small strain rate have been used to study the effects of mixed corrosion and creep processes in condensers cooled by sea or synthetic sea waters. The results of corrosion creep tests and K1scc calculations are given. The Russian science activities concerning condensers manufactured from titanium show the possibilities for designing structures with very high level service reliability in different corrosion aggressive mediums with high total salt, Cl-ion and oxygen contents. (orig.)

Advances in processing technologies for titanium heat exchanger tubes of fossil and nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Likhareva, T.P.; Tchizhik, A.A.; Chavchanidze, N.N. [Polzanov Central Boiler and Turbine Institute, St. Petersburg (Russian Federation)

1998-12-31

The advances in processing technologies for titanium heat exchangers with rolled and welded tubes of fossil and nuclear power plants in Russia are presented. The special methodology of investigations with constant small strain rate have been used to study the effects of mixed corrosion and creep processes in condensers cooled by sea or synthetic sea waters. The results of corrosion creep tests and K1scc calculations are given. The Russian science activities concerning condensers manufactured from titanium show the possibilities for designing structures with very high level service reliability in different corrosion aggressive mediums with high total salt, Cl-ion and oxygen contents. (orig.)

Physical explosion analysis in heat exchanger network design

Science.gov (United States)

Pasha, M.; Zaini, D.; Shariff, A. M.

2016-06-01

The failure of shell and tube heat exchangers is being extensively experienced by the chemical process industries. This failure can create a loss of production for long time duration. Moreover, loss of containment through heat exchanger could potentially lead to a credible event such as fire, explosion and toxic release. There is a need to analyse the possible worst case effect originated from the loss of containment of the heat exchanger at the early design stage. Physical explosion analysis during the heat exchanger network design is presented in this work. Baker and Prugh explosion models are deployed for assessing the explosion effect. Microsoft Excel integrated with process design simulator through object linking and embedded (OLE) automation for this analysis. Aspen HYSYS V (8.0) used as a simulation platform in this work. A typical heat exchanger network of steam reforming and shift conversion process was presented as a case study. It is investigated from this analysis that overpressure generated from the physical explosion of each heat exchanger can be estimated in a more precise manner by using Prugh model. The present work could potentially assist the design engineer to identify the critical heat exchanger in the network at the preliminary design stage.

Heat exchanger restart evaluation

International Nuclear Information System (INIS)

Morrison, J.M.; Hirst, C.W.; Lentz, T.F.

1992-01-01

On December 24, 1991, the K-Reactor was in the shutdown mode with full AC process water flow and full cooling water flow. Safety rod testing was being performed as part of the power ascension testing program. The results of cooling water samples indicated tritium concentrations higher than allowable. Further sampling and testing confirmed a Process Water System to Cooling Water System leak in heat exchanger 4A (HX 4A). The heat exchanger was isolated and the plant shutdown. Heat exchanger 4A was removed from the plant and moved to C-Area prior to performing examinations and diagnostic testing. This included locating and identifying the leaking tube or tubes, eddy current examination of the leaking tube and a number of adjacent tubes, visually inspecting the leaking tube from both the inside as well as the area surrounding the identified tube. The leaking tube was removed and examined metallurgically to determine the failure mechanism. In addition ten other tubes that either exhibited eddy current indications or would represent a baseline condition were removed from heat exchanger 4A for metallurgical examination. Additional analysis and review of heat exchanger leakage history was performed to determine if there are any patterns which can be used for predictive purposes. Compensatory actions have been taken to improve the sensitivity and response time to any future events of this type. The results of these actions are summarized

Heat exchanger restart evaluation

International Nuclear Information System (INIS)

Morrison, J.M.; Hirst, C.W.; Lentz, T.F.

1992-01-01

On December 24, 1991, the K-Reactor was in the shutdown mode with full AC process water flow and full cooling water flow. Safety rod testing was being performed as part of the power ascension testing program. The results of cooling water samples indicated tritium concentrations higher than allowable. Further sampling and testing confirmed a Process Water System to Cooling Water System leak in heat exchanger 4A (HX 4A). The heat exchanger was isolated and the plant shutdown. Heat exchanger 4A was removed from the plant and moved to C-Area prior to performing examinations and diagnostic testing. This included locating and identifying the leaking tube or tubes, eddy current examination of the leaking tube and a number of adjacent tubes, visually inspecting the leaking tube from both the inside as well as the area surrounding the identified tube. The leaking tube was removed and examined metallurgically to determine the failure mechanism. In addition ten other tubes that either exhibited eddy current indications or would represent a baseline condition were removed from heat exchanger 4A for metallurgical examination. Additional analysis and review of heat exchanger leakage history was performed to determine if there are any patterns which can be used for predictive purposes. Compensatory actions have been taken to improve the sensitivity and response time to any future events of this type. The results of these actions are summary herein

Small Column Ion Exchange

International Nuclear Information System (INIS)

Huff, Thomas

2010-01-01

Small Column Ion Exchange (SCIX) leverages a suite of technologies developed by DOE across the complex to achieve lifecycle savings. Technologies are applicable to multiple sites. Early testing supported multiple sites. Balance of SRS SCIX testing supports SRS deployment. A forma Systems Engineering Evaluation (SEE) was performed and selected Small Column Ion Exchange columns containing Crystalline Silicotitanate (CST) in a 2-column lead/lag configuration. SEE considered use of Spherical Resorcinol-Formaldehyde (sRF). Advantages of approach at SRS include: (1) no new buildings, (2) low volume of Cs waste in solid form compared to aqueous strip effluent; and availability of downstream processing facilities for immediate processing of spent resin.

Investigation of the Dynamic Melting Process in a Thermal Energy Storage Unit Using a Helical Coil Heat Exchanger

Directory of Open Access Journals (Sweden)

Xun Yang

2017-08-01

Full Text Available In this study, the dynamic melting process of the phase change material (PCM in a vertical cylindrical tube-in-tank thermal energy storage (TES unit was investigated through numerical simulations and experimental measurements. To ensure good heat exchange performance, a concentric helical coil was inserted into the TES unit to pipe the heat transfer fluid (HTF. A numerical model using the computational fluid dynamics (CFD approach was developed based on the enthalpy-porosity method to simulate the unsteady melting process including temperature and liquid fraction variations. Temperature measurements using evenly spaced thermocouples were conducted, and the temperature variation at three locations inside the TES unit was recorded. The effects of the HTF inlet parameters were investigated by parametric studies with different temperatures and flow rate values. Reasonably good agreement was achieved between the numerical prediction and the temperature measurement, which confirmed the numerical simulation accuracy. The numerical results showed the significance of buoyancy effect for the dynamic melting process. The system TES performance was very sensitive to the HTF inlet temperature. By contrast, no apparent influences can be found when changing the HTF flow rates. This study provides a comprehensive solution to investigate the heat exchange process of the TES system using PCM.

Hydrogen production by high-temperature gas-cooled reactor. Conceptual design of advanced process heat exchangers of the HTTR-IS hydrogen production system

International Nuclear Information System (INIS)

Sakaba, Nariaki; Ohashi, Hirofumi; Sato, Hiroyuki; Hara, Teruo; Kato, Ryoma; Kunitomi, Kazuhiko

2008-01-01

Nuclear hydrogen production is necessary in an anticipated hydrogen society that demands a massive quantity of hydrogen without economic disadvantage. Japan Atomic Energy Agency (JAEA) has launched the conceptual design study of a hydrogen production system with a near-term plan to connect it to Japan's first high-temperature gas-cooled reactor HTTR. The candidate hydrogen production system is based on the thermochemical water-splitting iodine sulphur (IS) process.The heat of 10 MWth at approximately 900degC, which can be provided by the secondary helium from the intermediate heat exchanger of the HTTR, is the energy input to the hydrogen production system. In this paper, we describe the recent progresses made in the conceptual design of advanced process heat exchangers of the HTTR-IS hydrogen production system. A new concept of sulphuric acid decomposer is proposed. This involves the integration of three separate functions of sulphuric acid decomposer, sulphur trioxide decomposer, and process heat exchanger. A new mixer-settler type of Bunsen reactor is also designed. This integrates three separate functions of Bunsen reactor, phase separator, and pump. The new concepts are expected to result in improved economics through construction and operation cost reductions because the number of process equipment and complicated connections between the equipment has been substantially reduced. (author)

Diffusion bonding in compact heat exchangers

International Nuclear Information System (INIS)

Southall, David

2009-01-01

Heatric's diffusion bonding process is a solid-state joining technology that produces strong, compact, all-metal heat exchanger cores. Diffusion bonding allows for a large quantity of joints to be made in geometries that would normally be inaccessible for conventional welding techniques. Since Heatric's diffusion bonding process uses no interlayer or braze alloy, the resulting heat exchanger core has consistent chemistry throughout and, under carefully controlled conditions, a return to parent metal strength can be reached. This paper will provide an overview of the diffusion bonding process and its origins, and also its application to compact heat exchanger construction. The paper will then discuss recent work that has been done to compare mechanical properties of Heatric's diffusion bonded material with material that has been conventionally welded, as well as with material tested in the as-received condition. (author)

Sleeving repair of heat exchanger tubes

International Nuclear Information System (INIS)

Street, Michael D.; Schafer, Bruce W.

2000-01-01

Defective heat exchanger tubes can be repaired using techniques that do not involve the cost and schedule penalties of component replacement. FTI's years of experience repairing steam generator tubes have been successfully applied to heat exchangers. Framatome Technologies heat exchanger sleeves can bridge defective areas of the heat exchanger tubes, sleeves have been designed to repair typical heat exchanger tube defects caused by excessive tube vibration, stress corrosion cracking, pitting or erosion. By installing a sleeve, the majority of the tube's heat transfer and flow capacity is maintained and the need to replace the heat exchanger can be delayed or eliminated. Both performance and reliability are improved. FTI typically installs heat exchanger tube sleeves using either a roll expansion or hydraulic expansion process. While roll expansion of a sleeve can be accomplished very quickly, hydraulic expansion allows sleeves to be installed deep within a tube where a roll expander cannot reach. Benefits of FTI's heat exchanger tube sleeving techniques include: - Sleeves can be positioned any where along the tube length, and for precise positioning of the sleeve eddy current techniques can be employed. - Varying sleeve lengths can be used. - Both the roll and hydraulic expansion processes are rapid and both produce joints that do not require stress relief. - Because of low leak rates and speed of installations, sleeves can be used to preventatively repair likely-to-fail tubes. - Sleeves can be used for tube stiffening and to limit leakage through tube defects. - Because of installation speed, there is minimal impact on outage schedules and budgets. FTI's recently installed heat exchanger sleeving at the Kori-3 Nuclear Power Station in conjunction with Korea Plant Service and Engineering Co., Ltd. The sleeves were installed in the 3A and 3B component cooling water heat exchangers. A total of 859 tubesheet and 68 freespan sleeves were installed in the 3A heat

Ion exchange treatment of rinse water generated in the galvanizing process.

Science.gov (United States)

Marañón, Elena; Fernández, Yolanda; Castrillón, Leonor

2005-01-01

A study was conducted of the viability of using the cationic exchange resins Amberlite IR-120 and Lewatit SP-112 to treat rinse water generated in the galvanizing process as well as acidic wastewater containing zinc (Zn) and iron (Fe). Solutions containing either 100 mg/L of Zn at pH 5.6 (rinse water) or Fe and Zn at concentrations of 320 and 200 mg/L at pH 1.5 (acidic water), respectively, were percolated through packed beds until the resins were exhausted. Breakthrough capacities obtained ranged between 1.1 and 1.5 meq metal/mL resin. The elution of metal and the regeneration of resins were performed with hydrochloric acid. The influence of the flowrate used during the loading stage was also studied, with 0.5 bed volumes/min (3.2 cm/min) found to be the optimum flowrate.

Process Control Security in the Cybercrime Information Exchange NICC

NARCIS (Netherlands)

Luiijf, H.A.M.

2009-01-01

Detecting, investigating and prosecuting cybercrime? Extremely important, but not really the solution for the problem. Prevention is better! The sectors that have joined the Cybercrime Information Exchange have accepted the challenge of ensuring the effectiveness of the (information) security of

The Intercultural and Non-Formal Learning Processes of Children in Primary School Exchange Programmes in France and Germany

Science.gov (United States)

Melin, Valérie; Wagner, Bernd

2015-01-01

This paper is based on educational anthropology, and presents the initial findings of a three-year international comparative study of primary school children's learning-processes during travel and cross-cultural encounters. A French-German research team investigated and here reports on primary school exchange programmes. Open coding of the…

Gas exchange between the forest and the atmosphere

International Nuclear Information System (INIS)

Murphy, C.E. Jr.

1985-01-01

Forest gas exchange is discussed in terms of the processes that control the rate of exchange with the atmosphere. Examples are presented to show how vegetative uptake control is varied for gases with different characteristics. The prediction of uptake for large areas and over long periods of time is discussed in terms of quantitative models of the gas exchange processes. Finally, remote sensing is suggested as a means of obtaining the parameters needed to make the model predictions. 46 refs., 6 figs

Study of Aging ion exchange membranes used in separation processes

International Nuclear Information System (INIS)

Bellakhal, N.; Ghalloussi, R.; Dammak, L.

2009-01-01

Presently, the most important application of ion exchange membranes (IEM) is the electrodialysis. This technique consists of a membrane separation using a series of anion exchange membranes alternately and cations, often used for the desalination of brackish water. These membranes are confronted with problems of aging. Indeed, the more they are used more physical and chemical properties will change. A comparative study of the behavior of both EMI and new but the same treatment is carried out by measuring a magnitude transfer characteristic: ion permeability. Ionic permeability is a physical quantity can have an idea about the selectivity of the membrane towards the charged species and the p orosity o f the membrane. It is a transport of ions (cations + anions) through the membrane. Thus, determining the ion permeability is to determine the diffusion flux of a strong electrolyte through a membrane separating two compartments (one containing electrolytes and other water initially ultrapure who will gradually electrolyte through the membrane). The measurement technique used is that by conductimetric detection because of the ease of its implementation and its accuracy. Thus, the variation of the concentration of the electrolyte is continuously monitored by measuring the conductivity of the solution diluted with time. The curves s = f (t) MEA and MEC new and used varying concentration of the electrolyte membranes show that let in less waste of strong electrolyte (NaCl and HCl) than new ones. This can be explained by: - The functional sites are combined with polyvalent ions present even in trace amounts in the solution process and become inactive. The membrane loses its hydrophilic character and turns into a film almost hydrophobic. - The chemical attacks and electrodialysis operations have degraded and eliminated much of the fixed sites leading to the same effects on the hydrophilic membrane. - These two assumptions have been reinforced by the extent of exchange

Role of Exchange Rate Volatility in Exchange Rate Pass-Through to Import Prices: Some Evidence from Japan

OpenAIRE

Guneratne Banda Wickremasinghe; Param Silvapulle

2004-01-01

This paper investigates the effect of exchange rate volatility on the degree of exchange rate pass-through in Japan for the period January 1975 to June 1997. Although several studies put forward theoretical arguments for the volatility-domestic import price relationship, only a very few studies produced empirical evidence. The volatility of contractual currency based exchange rate index returns was modelled using GARCH-type processes with skewed student t-distribution, capturing the typical n...

Charge exchange in collisions of beryllium with its ion.

Science.gov (United States)

Zhang, Peng; Dalgarno, Alexander; Côté, Robin; Bodo, Enrico

2011-11-14

Close-coupling calculations of the resonance and near resonance charge exchange in ion-atom collisions of Be at low and intermediate energies are presented. Accurate ab initio calculations are carried out of the Born-Oppenheimer potentials and the non-adiabatic couplings that are due to the finite nuclear masses and drive the near resonance charge exchange. We show that the near resonance charge exchange cross section follows Wigner's threshold law of inelastic processes for energies below 10(-8) eV and that the zero temperature rate constant for it is 4.5 × 10(-10) cm(3) s(-1). At collision energies much larger than the isotope shift of the ionization potentials of the atoms, we show that the near resonance charge exchange process is equivalent to the resonance charge exchange with cross sections having a logarithmic dependence. We also investigate the perturbation to the charge exchange process due to the non-adiabatic interaction to an electronic excited state. We show that the influence is negligible at low temperatures and still small at intermediate energies despite the presence of resonances.

Isotope exchange of strontium and molybdate ions in strontium polymolybdates

International Nuclear Information System (INIS)

Atun, G.

2002-01-01

The heterogeneous isotopic exchange reactions in strontium polymolybdates of Sr 2+ and MoO 4 2- ions in the strontium nitrate and sodium molybdate solutions have been studied using 90 Sr and 99 Mo as tracers. Electrometric methods have been used to study the compositions of strontium molybdates obtained by adding strontium chloride to a progressively acidified solution of sodium molybdate. It has been found that the exchange fraction increases with increasing chain length of strontium polymolybdate. The exchange equilibrium constant (K ex ) has been calculated between 298 and 348 K as well as ΔG deg, ΔH deg and ΔS deg. The results indicate that Sr 2+ cations have a much higher affinity for exchangers than MoO 4 2- anions. By fitting the data to the Dubinin-Radushkevich (D-R) isotherm it has been shown that the exchange capacity (X m ) for both ions is affected by the ion adsorption process at low temperatures and by the ion exchange process at high temperatures. At high concentrations, the recrystallization process contributes to on the cation exchange but is ineffective on the anion exchange mechanism. (author)

MODELING AN ION EXCHANGE PROCESS FOR CESIUM REMOVAL FROM ALKALINE RADIOACTIVE WASTE SOLUTIONS

International Nuclear Information System (INIS)

Smith, F.; Hamm, Luther; Aleman, Sebastian; Michael, Johnston

2008-01-01

The performance of spherical Resorcinol-Formaldehyde ion-exchange resin for the removal of cesium from alkaline radioactive waste solutions has been investigated through computer modeling. Cesium adsorption isotherms were obtained by fitting experimental data using a thermodynamic framework. Results show that ion-exchange is an efficient method for cesium removal from highly alkaline radioactive waste solutions. On average, two 1300 liter columns operating in series are able to treat 690,000 liters of waste with an initial cesium concentration of 0.09 mM in 11 days achieving a decontamination factor of over 50,000. The study also tested the sensitivity of ion-exchange column performance to variations in flow rate, temperature and column dimensions. Modeling results can be used to optimize design of the ion exchange system

F- and H-Area Seepage Basins Water Treatment System Process Optimization and Alternative Chemistry Ion Exchange/Sorbent Material Screening Clearwell Overflow Study

Energy Technology Data Exchange (ETDEWEB)

Serkiz, S.M.

2000-08-30

This study investigated alternative ion exchange/sorbent materials and polishing chemistries designed to remove specific radionuclides not removed during the neutralization/precipitation/clarification process.

Numerical analysis of the heat and mass transfer processes in selected M-Cycle heat exchangers for the dew point evaporative cooling

International Nuclear Information System (INIS)

Pandelidis, Demis; Anisimov, Sergey

2015-01-01

Highlights: • The comparative numerical study of the eight M-Cycle heat exchangers was presented. • The mathematical model is compared against the experimental data. • The results show, that the original M-Cycle heat and mass exchanger can be improved. • The effectiveness of the heat and mass exchangers depends strongly on the inlet air parameters. - Abstract: This paper investigates a mathematical simulation of heat and mass transfer in eight different types of the Maisotsenko Cycle (M-Cycle) heat and mass exchangers (HMXs) used for indirect evaporative air cooling. A two-dimensional heat and mass transfer model is developed to perform the thermal calculations of the indirect evaporative cooling process and quantifying the overall performance. The mathematical model was validated against experimental data. A numerical simulation reveals many unique features of the considered HMXs, enabling an accurate prediction of their performance. Results of the model allow for comparison of the analyzed devices in order to improve the performance of the original HMX

Ion-exchange properties of natural mordenite

International Nuclear Information System (INIS)

Chelishchev, N.F.; Volodin, V.F.

1977-01-01

Ion exchange properties are studied of natural mordenite Si(Al=4.75) exhibiting adequate mechanical characteristics and sufficient resistance to high temperature acids. Consideration is given to the pattern of exchange ions distribution among mordenite and chloride solutions of K, Cs, Rb, Sr. Mordenite shows sharp selectivity towards large alkali metal cations, particularly Cs + . In these processes the exchange isotherms are characterized by the constant selectivity towards a counterion. For the Sr 2+ -2Na + exchange the isotherm shows a change of selectivity after a definite counterion concentration has been reached in the solution. Correlation between the exchange thermodynamic constants makes it possible to propose the following range of mordenite selectivity towards the cations under study: Cs>Rb>K>Na>Sr

Floating Exchange Rate Regime

OpenAIRE

Quader, Syed Manzur

2004-01-01

In recent years, many developing countries having a history of high inflation, unfavorable balance of payment situation and a high level of foreign currencies denominated debt, have switched or are in the process of switching to a more flexible exchange rate regime. Therefore, the stability of the exchange rate and the dynamics of its volatility are more crucial than before to prevent financial crises and macroeconomic disturbances. This paper is designed to find out the reasons behind Bangla...

Method of solidifying radioactive ion exchange resin

International Nuclear Information System (INIS)

Minami, Yuji; Tomita, Toshihide

1989-01-01

Spent anion exchange resin formed in nuclear power plants, etc. generally catch only a portion of anions in view of the ion exchange resins capacity and most of the anions are sent while possessing activities to radioactive waste processing systems. Then, the anion exchange resins increase the specific gravity by the capture of the anions. Accordingly, anions are caused to be captured on the anion exchange resin wastes such that the specific gravity of the anion exchange resin wastes is greater than that of the thermosetting resins to be mixed. This enables satisfactory mixing with the thermosetting resins and, in addition, enables to form integral solidification products in which anion exchange resins and cation exchange resins are not locallized separately and which are homogenous and free from cracks. (T.M.)

Stakeholder engagement and knowledge exchange in environmental research.

Science.gov (United States)

Phillipson, Jeremy; Lowe, Philip; Proctor, Amy; Ruto, Eric

2012-03-01

It is commonly put forward that effective uptake of research in policy or practice must be built upon a foundation of active knowledge exchange and stakeholder engagement during the research. However, what is often lacking is a systematic appreciation of the specific practices of knowledge exchange and their relative merits. The paper reports on a 2009 survey of 21 research projects within the UK Research Councils' Rural Economy and Land Use Programme regarding the involvement and perceived impact of over a thousand stakeholders in the research. The survey reveals that most stakeholders were involved as research subjects or as event participants. Large numbers were also engaged in the research process itself, including involvement in shaping the direction of research. Stakeholder engagement is perceived as bringing significant benefits to the process of knowledge production. A close relationship is found between mechanisms and approaches to knowledge exchange and the spread of benefits for researchers and stakeholders. Mutual benefits are gained from exchange of staff or where stakeholders are members of research advisory groups. Different stakeholder sectors are also associated with different patterns of engagement, which lead to contrasting impact patterns. Any efforts to alter knowledge exchange processes and outcomes must overcome these differing engagement tendencies. Overall, much greater attention should be given to early processes of knowledge exchange and stakeholder engagement within the lifetime of research projects. Copyright © 2011 Elsevier Ltd. All rights reserved.

Smart coating process of proton-exchange membrane for polymer electrolyte fuel cell

International Nuclear Information System (INIS)

Leu, Hoang-Jyh; Chiu, Kuo-Feng; Lin, Chiu-Yue

2013-01-01

Highlights: ► Using oxygen plasma and smart coating technique for membrane modification. ► Oxygen plasma treatment can increase the reaction area of the membrane. ► AFM, SEM, FT-IR, XPS, EIS spectra can prove the surface treatment process. ► Nafion membrane modification can reduce Rct and enhance current density. - Abstract: The interfaces of electrolyte|catalyst|electrode play an important role in the performance of proton-exchange membrane fuel cells (PEMFCs). Increasing the interface effective area and lowering the charge transfer resistance of the interface are significant issues to promote the cell performance. In this study, oxygen plasma treatment was used to increase the surface roughness of Nafion®117 membrane, and then a smart coating process was applied to fabricate the initial Pt/C catalyst layer, which served to reduce the charge transfer resistance of the interface. The morphology and surface characteristics of membranes have been qualified by scanning electron microscopy, atomic force microscopy and X-ray photoelectron spectroscopy. These results show that the plasma treatments and smart coating processes were effective in reducing the interface charge transfer resistance. At optimal condition, the interface charge transfer resistance was 0.45 Ω/cm 2 which was 1–2 order less than the untreated ones

Intermediate heat exchanger for HTR process heat application

International Nuclear Information System (INIS)

Crambes, M.

1980-01-01

In the French study on the nuclear gasification of coal, the following options were recommended: Coal hydrogenation, the hydrogen being derived from CH 4 reforming under the effects of HTR heat; the use of an intermediate helium circuit between the nuclear plant and the reforming plant. The purpose of the present paper is to describe the heat exchanger designed to transfer heat from the primary to the intermediate circuit

SPEEDUPtrademark ion exchange column model

International Nuclear Information System (INIS)

Hang, T.

2000-01-01

A transient model to describe the process of loading a solute onto the granular fixed bed in an ion exchange (IX) column has been developed using the SpeedUptrademark software package. SpeedUp offers the advantage of smooth integration into other existing SpeedUp flowsheet models. The mathematical algorithm of a porous particle diffusion model was adopted to account for convection, axial dispersion, film mass transfer, and pore diffusion. The method of orthogonal collocation on finite elements was employed to solve the governing transport equations. The model allows the use of a non-linear Langmuir isotherm based on an effective binary ionic exchange process. The SpeedUp column model was tested by comparing to the analytical solutions of three transport problems from the ion exchange literature. In addition, a sample calculation of a train of three crystalline silicotitanate (CST) IX columns in series was made using both the SpeedUp model and Purdue University's VERSE-LC code. All test cases showed excellent agreement between the SpeedUp model results and the test data. The model can be readily used for SuperLigtrademark ion exchange resins, once the experimental data are complete

Capture and isotopic exchange method for water and hydrogen isotopes on zeolite catalysts up to technical scale for pre-study of processing highly tritiated water

Energy Technology Data Exchange (ETDEWEB)

Michling, R.; Braun, A.; Cristescu, I.; Dittrich, H.; Gramlich, N.; Lohr, N. [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany); Glugla, M.; Shu, W.; Willms, S. [ITER Organization, Saint-Paul-lez-Durance (France)

2015-03-15

Highly tritiated water (HTW) may be generated at ITER by various processes and, due to the excessive radio toxicity, the self-radiolysis and the exceedingly corrosive property of HTW, a potential hazard is associated with its storage and process. Therefore, the capture and exchange method for HTW utilizing Molecular Sieve Beds (MSB) was investigated in view of adsorption capacity, isotopic exchange performance and process parameters. For the MSB, different types of zeolite were selected. All zeolite materials were additionally coated with platinum. The following work comprised the selection of the most efficient zeolite candidate based on detailed parametric studies during the H{sub 2}/D{sub 2}O laboratory scale exchange experiments (about 25 g zeolite per bed) at the Tritium Laboratory Karlsruhe (TLK). For the zeolite, characterization analytical techniques such as Infrared Spectroscopy, Thermogravimetry and online mass spectrometry were implemented. Followed by further investigation of the selected zeolite catalyst under full technical operation, a MSB (about 22 kg zeolite) was processed with hydrogen flow rates up to 60 mol*h{sup -1} and deuterated water loads up to 1.6 kg in view of later ITER processing of arising HTW. (authors)

Increase of ionic conductivity in the microporous lithosilicate RUB-29 by Na-ion exchange processes

International Nuclear Information System (INIS)

Park, S.-H.; Senyshyn, A.; Paulmann, C.

2007-01-01

The ionic conductivity in the zeolite-like lithosilicate RUB-29 (Cs 14 Li 24 [Li 18 Si 72 O 172 ].14H 2 O [S.-H. Park, J.B. Parise, H. Gies, H. Liu, C.P. Grey, B.H. Toby, J. Am. Chem. Soc. 122 (2000) 11023-11024]) increases via simple ion-exchange processes, in particular when Na cations replace a part of Cs + and Li + of the material. The resulting ionic conductivity value of 3.2x10 -3 S cm -1 at 885 K is about two orders higher than that for the original material [S.-H. Park, J.B. Parise, M.E. Franke, T. Seydel, C. Paulmann, Micropor. Mesopor. Mater., in print ( (doi:10.1016/j.micromeso.2007.03.040) available online since April 19, 2007)]. The structural basis of a Na + -exchanged RUB-29 sample (Na-RUB-29) at 673 K could be elucidated by means of neutron powder diffraction. Rietveld refinements confirmed the replacement of Na + for both parts of Cs and Li cations, agreeing with idealized cell content, Na 8 Cs 8 Li 40 Si 72 O 172 . As a result of the incorporation of Na + in large pores, the number of Li + vacancies in dense Li 2 O-layers of the structure could increase. This can be one of the main reasons for the improved conductivity in Na-RUB-29. In addition, mobile Na cations may also contribute to the conductivity in Na-RUB-29 as continuous scattering length densities were found around the sites for Na in difference Fourier map. - Graphical abstract: Li 2 O-layers formed by edge- and corner-sharing LiO 4 - and LiO 3 -moieties in the zeolite-like lithosilicate RUB-29 provide optimal pathways for conducting Li + . The number of empty Li sites in this layer-like configuration could increase via 'simple' Na + -exchange processes, promoting fast Li motions

Moist Orographic Convection: Physical Mechanisms and Links to Surface-Exchange Processes

Directory of Open Access Journals (Sweden)

Daniel J. Kirshbaum

2018-02-01

Full Text Available This paper reviews the current understanding of moist orographic convection and its regulation by surface-exchange processes. Such convection tends to develop when and where moist instability coincides with sufficient terrain-induced ascent to locally overcome convective inhibition. The terrain-induced ascent can be owing to mechanical (airflow over or around an obstacle and/or thermal (differential heating over sloping terrain forcing. For the former, the location of convective initiation depends on the dynamical flow regime. In “unblocked” flows that ascend the barrier, the convection tends to initiate over the windward slopes, while in “blocked” flows that detour around the barrier, the convection tends to initiate upstream and/or downstream of the high terrain where impinging flows split and rejoin, respectively. Processes that destabilize the upstream flow for mechanically forced moist convection include large-scale moistening and ascent, positive surface sensible and latent heat fluxes, and differential advection in baroclinic zones. For thermally forced flows, convective initiation is driven by thermally direct circulations with sharp updrafts over or downwind of the mountain crest (daytime or foot (nighttime. Along with the larger-scale background flow, local evapotranspiration and transport of moisture, as well as thermodynamic heterogeneities over the complex terrain, regulate moist instability in such events. Longstanding limitations in the quantitative understanding of related processes, including both convective preconditioning and initiation, must be overcome to improve the prediction of this convection, and its collective effects, in weather and climate models.

Tritium stripping by a catalytic exchange stripper

International Nuclear Information System (INIS)

Heung, L.K.; Gibson, G.W.; Ortman, M.S.

1991-01-01

A catalytic exchange process for stripping elemental tritium from gas streams has been demonstrated. The process uses a catalyzed isotopic exchange reaction between tritium in the gas phase and protium or deuterium in the solid phase on alumina. The reaction is catalyzed by platinum deposited on the alumina. The process has been tested with both tritium and deuterium. Decontamination factors (ration of inlet and outlet tritium concentrations) as high as 1000 have been achieved, depending on inlet concentration. The test results and some demonstrated applications are presented

SPECIAL ANALYSIS FOR SLIT TRENCH DISPOSAL OF THE REACTOR PROCESS HEAT EXCHANGERS

Energy Technology Data Exchange (ETDEWEB)

Hamm, L.; Collard, L.; Aleman, S.; Gorensek, M.; Butcher, T.

2012-06-18

The Savannah River National Laboratory (SRNL), in response to a request from Solid Waste Management (SWM), conducted a Special Analysis (SA) to evaluate the performance of nineteen heat exchangers that are to be disposed in the E-Area low level waste facility Slit Trench 9 (ST 9). Although these nineteen heat exchangers were never decontaminated, the majority of the radionuclides in the heat exchanger inventory list were determined to be acceptable for burial because they are less than the 'generic' waste form inventory limits given in the 2008 Performance Assessment (PA) (WSRC, 2008). However, as generic waste, the H-3 and C-14 inventories resulted in unacceptable sum-of-fractions (SOFs). Initial scoping analyses performed by SRNL indicated that if alterations were made to certain external nozzles to mitigate various potential leak paths, acceptable SOFs could be achieved through the use of a 'Special' waste form. This SA provides the technical basis for this new 'Special' waste form and provides the inventory limits for H-3 and C-14 for these nineteen heat exchangers such that the nineteen heat exchangers can be disposed in ST 9. This 'Special' waste form is limited to these nineteen heat exchangers in ST 9 and applies for H-3 and C-14, which are designated as H-3X and C-14X, respectively. The SA follows the same methodology used in the 2008 PA and the 2008 SA except for the modeling enhancements noted below. Infiltration rates above the heat exchangers are identical to those used in the 2008 PA; however, flow through the heat exchangers is unique. Because it is unknown exactly how sealed heat exchanger openings will perform and how surface and embedded contaminants will be released, multiple base cases or scenarios were established to investigate a set of performances. Each scenario consists of flow options (based on the performance of sealed openings) and a near-field release of contaminants (based on corrosion and

Ion-exchange-resin-catalyzed adamantylation of phenol derivatives with adamantanols: Developing a clean process for synthesis of 2-(1-adamantyl-4-bromophenol, a key intermediate of adapalene

Directory of Open Access Journals (Sweden)

Nan Wang

2012-02-01

Full Text Available A clean process has been developed for the synthesis of 2-adamantylphenol derivatives through adamantylation of substituted phenols with adamantanols catalyzed by commercially available and recyclable ion-exchange sulfonic acid resin in acetic acid. The sole byproduct of the adamantylation reaction, namely water, could be converted into the solvent acetic acid by addition of a slight excess of acetic anhydride during the work-up procedure, making the process waste-free except for regeneration of the ion-exchange resin, and facilitating the recycling of the resin catalyst. The ion-exchange sulfonic acid resin catalyst could be readily recycled by filtration and directly reused at least ten times without a significant loss of activity. The key intermediate of adapalene, 2-(1-adamantyl-4-bromophenol, could be produced by means of this waste-free process.

Hydrogen--deuterium exchanges in nucleosides and nucleotides. A mechanism for exchange of the exocyclic amino hydrogens of adenosine

International Nuclear Information System (INIS)

Cross, D.G.; Brown, A.; Fisher, H.F.

1975-01-01

The pH dependence of the apparent first-order rate constant for the exchange of the exocyclic amino hydrogens of adenosine with deuterium from the solvent was measured by stopped-flow ultraviolet spectroscopy. This dependence shows acid catalysis, base catalysis, and spontaneous exchange at neutral pH values. A study of the effect of several buffers on the rates of exchange reveals both general acid and general base catalytic behavior for the exchange process. We propose a general mechanism for the exchange which requires N-1 protonated adenosine as an intermediate for the acid-catalyzed exchange and amidine anion for the base-catalyzed exchange. In both cases the rate-limiting step is the base-catalyzed abstraction of a proton from the exocyclic amino moiety. Evaluation of the rate constants predicts the equilibrium for the exocyclic amino/imino tautomers to be 6.3 x 10 3 :1. (U.S.)

Rod-shaped ion exchanger useful for purifying liquids or recovering components from liquids comprises a metal wire core surrounded by an ion-exchange resin

NARCIS (Netherlands)

Koopman, C.; Witkamp, G.J.

2002-01-01

Rod-shaped ion exchanger comprises a metal wire core surrounded by an ion-exchange resin. Independent claims are also included for: (1) a module comprising a housing with an inlet and outlet and one or more ion exchangers as above; (2) a process for producing an ion exchanger as above, comprising

Transversity Amplitudes in Hypercharge Exchange Processes; Amplitudes de transversidad en procesos de intercambio de hipercarga

Energy Technology Data Exchange (ETDEWEB)

Aguilar Benitez de Lugo, M.

1979-07-01

In this work we present several techniques developed for the extraction of the. Transversity amplitudes governing quasi two-body meson baryon reactions with hypercharge exchange. We review the methods used In processes having a pure spin configuration, as well as the more relevant results obtained with data from K{sup p} and Tp interactions at intermediate energies. The predictions of the additive quark model and the ones following from exchange degeneracy and etoxicity are discussed. We present a formalism for amplitude analysis developed for reactions with mixed spin configurations and discuss the methods of parametric estimation of the moduli and phases of.the amplitudes, as well as the various tests employed to check the goodness of the fits. The calculation of the generalized joint density matrices is given and we propose a method based on the generalization of the idea of multipole moments, which allows to investigate the structure of the decay angular correlations and establishes the quality of the fits and the validity of the simplifying assumptions currently used in this type of studies. (Author) 43 refs.

Crystalline silicotitanates -- novel commercial cesium ion exchangers

International Nuclear Information System (INIS)

Braun, R.; Dangieri, T.J.; Fennelly, D.J.

1996-01-01

A new class of inorganic ion exchangers called crystalline silicotitanates (CST), invented by researchers at Sandia National Laboratories and Texas A ampersand M University, has been commercialized in a joint Sandia-UOP effort. The original developmental materials exhibited high selectivity for the ion exchange of cesium, strontium, and several other radionuclides from highly alkaline solutions containing molar concentrations of Na + . The materials also showed excellent chemical and radiation stability. These CST properties made them excellent candidates for treatment of solutions such as the Hanford tank supernates and other DOE radwastes. Sandia and UOP, under a Cooperative Research and Development Agreement (CRADA), developed CSTs in the powdered form and in an engineered form suitable for column ion exchange use. A continuous-flow, column ion exchange process is expected to be used to remove Cs and other radionuclides from the Hanford supernatant. The powder material invented by Sandia and Texas A ampersand M consists of submicron-size particles. It is not designed for column ion exchange but may be used in other applications such as batch waste processing. Data are also presented confirming the excellent stability of the commercial CSTs over a broad pH range and the high radiation stability of the exchangers. In addition, data are provided that demonstrate the high physical strength and attrition resistance of IONSIV reg-sign IE-911, critical properties for column ion exchange applications

Communication and Social Exchange Processes in Community Theater Groups

Science.gov (United States)

Kramer, Michael W.

2005-01-01

This study explores the communication experiences of two volunteer groups involved in the production of community theater musicals. Based on social exchange theory, it examined what group members perceived to be the positive benefits (primarily meeting people and having an opportunity to perform) and the negative costs (primarily disorganization,…

Chemical uranium enrichment with ion exchanger

International Nuclear Information System (INIS)

Takeda, Kunihiko; Onitsuka, Hatsuki; Obanawa, Heiichiro

1991-01-01

The uranium enrichment by using ion-exchange has been studied and developed since 1972. The ion-exchange rate has been improved approx. 3000 times and the electron exchange reaction, which occurs with ion-exchange reaction, was also accelerated with catalyst. Flow disturbance in a ion-exchange column has been fully studied and the value of turbulence has been reduced to 150μm. These results allowed us to design a very fine separation column, in which about 10000 stages can be obtained even when the column is more than 1 m in diameter. In the course of the development, a self-regenerating reaction between the redox agents was discovered and incorporated into the process, and has resulted in a reduction of 70 % in the separation energy requirement. (author)

Evaluating the Uncertainty in Exchange Parameters Determined from Off-Resonance R1ρ Relaxation Dispersion for Systems in Fast Exchange

Science.gov (United States)

Bothe, Jameson R.; Stein, Zachary W.; Al-Hashimi, Hashim M.

2014-01-01

Spin relaxation in the rotating frame (R1ρ) is a powerful NMR technique for characterizing fast microsecond timescale exchange processes directed toward short-lived excited states in biomolecules. At the limit of fast exchange, only kex = k1 + k−1 and Φıx = pGpE(Δω)2 can be determined from R1ρ data limiting the ability to characterize the structure and energetics of the excited state conformation. Here, we use simulations to examine the uncertainty with which exchange parameters can be determined for two state systems in intermediate-to-fast exchange using off-resonance R1ρ relaxation dispersion. R1ρ data computed by solving the Bloch-McConnell equations reveals small but significant asymmetry with respect to offset (R1ρ(ΔΩ) ≠ R1ρ(−ΔΩ)), which is a hallmark of slow-to-intermediate exchange, even under conditions of fast exchange for free precession chemical exchange line broadening (kex/Δω > 10). A grid search analysis combined with bootstrap and Monte-Carlo based statistical approaches for estimating uncertainty in exchange parameters reveals that both the sign and magnitude of Δω can be determined at a useful level of uncertainty for systems in fast exchange (kex/Δω exchange parameters. Results from simulations are complemented by analysis of experimental R1ρ data measured in three nucleic acid systems with exchange processes occurring on the slow (kex/Δω = 0.2; pE = ~ 0.7%), fast (kex/Δω = ~10–16; pE = ~13%) and very fast (kex = 39,000 s−1) chemical shift timescales. PMID:24819426

ASPECTS REGARDING THE DEVELOPMENT OF BUCHAREST STOCK EXCHANGE

Directory of Open Access Journals (Sweden)

Mirela MATEI

2008-12-01

Full Text Available Capital market in Romania is in a slow process of development, because the performances of the Bucharest Stock Exchange (BSE are ranking it among the last ones in Europe. The causes of slow development of capital market and remain behind compared to other Eastern European markets are numerous and consist of: late establishment of the two parts of the capital market û stock exchange and OTC market, modest use of capital market in the privatization process of state-owned companies; compromise of investment funds after scandals with SAFI and FNI; delay reform of the pension system, withdrawal from Bucharest Stock Exchange of major companies such as Dacia Pite║ti, Arctic Gπie║ti or Terapia Cluj Napoca, using bank credit as financing method of Romanian companies. Products lunched by BSE must satisfy the requirements of local and foreign investors who were already accustomed to derivatives launched by the Financial and Commodities Exchange from Sibiu. In addition, Bucharest Stock Exchange should use the experience of major European and American ones that run large financial processes of innovation and launched contracts on weather, volatility indices, price indexes for real estate, etc.

Data Exchanges and Verifications Online (DEVO)

Data.gov (United States)

Social Security Administration — DEVO is the back-end application for processing SSN verifications and data exchanges. DEVO uses modern technology for parameter driven processing of both batch and...

Kinetics of hydrogen isotope exchange reactions

International Nuclear Information System (INIS)

Gold, V.; McAdam, M.E.

1975-01-01

Under the influence of tritium β-radiation, 1,4-dioxan undergoes hydrogen exchange with the solvent water. The inhibition of the reaction by known electron scavengers (Ag + , Cu 2+ , Ni 2+ , Co 2+ , Zn 2+ , H 3 + O) and also by species with high reactivity towards hydroxyl radicals but negligible reactivity towards solvated electrons (N 3 - , Br - , SCN - ) has been examined in detail. γ-irradiation similarly induces hydrogen exchange. The action of scavengers is interpreted as requiring the involvement of two separately scavengeable primary radiolysis products in the sequence of reactions leading to exchange. The presence of electron scavengers, even at high concentration, does not totally inhibit the exchange, and a secondary exchange route, involving a low vacancy state of inhibitor cations, is considered responsible for the 'unscavengeable' portion of the reaction, by providing an alternative exchange route. Analogies are drawn between the exchange reaction and other radiation-induced reactions that are thought to involve spur processes. Some implication of radiation-chemical studies in water-alcohol mixtures are indicated. (author)

Materials for nuclear diffusion-bonded compact heat exchangers

International Nuclear Information System (INIS)

Li, Xiuqing; Smith, Tim; Kininmont, David; Dewson, Stephen John

2009-01-01

This paper discusses the characteristics of materials used in the manufacture of diffusion bonded compact heat exchangers. Heatric have successfully developed a wide range of alloys tailored to meet process and customer requirements. This paper will focus on two materials of interest to the nuclear industry: dual certified SS316/316L stainless steel and nickel-based alloy Inconel 617. Dual certified SS316/316L is the alloy used most widely in the manufacture of Heatric's compact heat exchangers. Its excellent mechanical and corrosion resistance properties make it a good choice for use with many heat transfer media, including water, carbon dioxide, liquid sodium, and helium. As part of Heatric's continuing product development programme, work has been done to investigate strengthening mechanisms of the alloy; this paper will focus in particular on the effects of nitrogen addition. Another area of Heatric's programme is Alloy 617. This alloy has recently been developed for diffusion bonded compact heat exchanger for high temperature nuclear applications, such as the intermediate heat exchanger (IHX) for the very high temperature nuclear reactors for production of electricity, hydrogen and process heat. This paper will focus on the effects of diffusion bonding process and cooling rate on the properties of alloy 617. This paper also compares the properties and discusses the applications of these two alloys to compact heat exchangers for various nuclear processes. (author)

Automatic Generation of Object Models for Process Planning and Control Purposes using an International standard for Information Exchange

Directory of Open Access Journals (Sweden)

Petter Falkman

2003-10-01

Full Text Available In this paper a formal mapping between static information models and dynamic models is presented. The static information models are given according to an international standard for product, process and resource information exchange, (ISO 10303-214. The dynamic models are described as Discrete Event Systems. The product, process and resource information is automatically converted into product routes and used for simulation, controller synthesis and verification. A high level language, combining Petri nets and process algebra, is presented and used for speci- fication of desired routes. A main implication of the presented method is that it enables the reuse of process information when creating dynamic models for process control. This method also enables simulation and verification to be conducted early in the development chain.

First results of a coated heat exchanger for the use in dehumidification and cooling processes

International Nuclear Information System (INIS)

Munz, Gunther M.; Bongs, C.; Morgenstern, A.; Lehmann, S.; Kummer, H.; Henning, H.-M.; Henninger, Stefan K.

2013-01-01

In this work a novel solar driven dehumidification and cooling system is presented. The core components of this combined system are a sorptive dehumidification device based on high performance sorptive coatings and a novel evacuated tube solar air collector providing the driving heat. The essential part of the system is the coated heat exchanger. The chosen adsorbent is attached to the heat exchanger surface by a newly developed coating technique. Besides a brief description of the novel components and the experimental setup, the development of the aluminum heat exchanger, the coating procedure and scale up for geometries comparable to the heat exchanger in the dehumidification setup, as well as a first characterization of a small-sized coated heat exchanger regarding water uptake and dehumidification performance are presented. For estimating an overall system performance, a 2-dimensional thermodynamic model was applied, using the parameters in focus for the development of heat exchanger, coating and demonstration system. Highlights: • A novel developed technology is applied for sorptive coating of heat exchangers. • Upscaling to dimensions of 100 × 100 × 400 mm 3 was successful. • A small scale heat exchanger was coated and characterized showing good results. • Evaluation of adsorbents and simulation of system performance were carried out. • SAPO-34 gives best performance for driving temperatures of 100 °C and above

Investigating Small-Scale Air–Sea Exchange Processes via Thermography

Directory of Open Access Journals (Sweden)

Jakob Kunz

2018-03-01

Full Text Available The exchange of trace gases such as carbon dioxide or methane between the atmosphere and the ocean plays a key role for the climate system. However, the investigation of air–sea gas exchange rates lacks fast and accurate measurement techniques that can also be used in the field, e.g., onboard a ship on the ocean. A promising way to overcome this deficiency is to use heat as a proxy tracer for gas transfer. Heat transfer rates across the aqueous boundary layer of the air–water interface can be measured via thermography with unprecedented temporal and spatial resolution in the order of minutes and meters, respectively. Either passive or active measurement schemes can be applied. Passive approaches rely on temperature differences across the water surface, which are caused naturally by radiative and evaporative cooling of the water surface. Active measurement schemes force an artificial heat flux through the aqueous boundary layer by means of heating a patch at the water surface with an appropriate heat source, such as a CO2 laser. The choice of the excitation signal is crucial. It is beneficial to apply periodic heat flux densities with different excitation frequencies. In this way, the air–water interface can be probed for its response in terms of temperature amplitude and phase shift between excitation signal and temperature response. This concept from linear system theory is also well established in the field of non-destructive material testing, where it is known as lock-in thermography. This article gives a short introduction into air–sea gas exchange, before it presents an overview of different thermographic measurement techniques used in wind-wave facilities and at sea starting with early implementations. The article closes with a novel multifrequency excitation scheme for even faster measurements.

Heat exchanger versus regenerator: A fundamental comparison

NARCIS (Netherlands)

Will, M.E.; Waele, de A.T.A.M.

2005-01-01

Irreversible processes in regenerators and heat exchangers limit the performance of cryocoolers. In this paper we compare the performance of cryocoolers, operating with regenerators and heat exchangers from a fundamental point of view. The losses in the two systems are calculated from the entropy

Fibrinogen Reduction During Selective Plasma Exchange due to Membrane Fouling.

Science.gov (United States)

Ohkubo, Atsushi; Okado, Tomokazu; Miyamoto, Satoko; Hashimoto, Yurie; Komori, Shigeto; Yamamoto, Motoki; Maeda, Takuma; Itagaki, Ayako; Yamamoto, Hiroko; Seshima, Hiroshi; Kurashima, Naoki; Iimori, Soichiro; Naito, Shotaro; Sohara, Eisei; Uchida, Shinichi; Rai, Tatemitsu

2017-06-01

Fibrinogen is substantially reduced by most plasmapheresis modalities but retained in selective plasma exchange using Evacure EC-4A10 (EC-4A). Although EC-4A's fibrinogen sieving coefficient is 0, a session of selective plasma exchange reduced fibrinogen by approximately 19%. Here, we investigated sieving coefficient in five patients. When the mean processed plasma volume was 1.15 × plasma volume, the mean reduction of fibrinogen during selective plasma exchange was approximately 15%. Fibrinogen sieving coefficient was 0 when the processed plasma volume was 1.0 L, increasing to 0.07 when the processed plasma volume was 3.0 L, with a mean of 0.03 during selective plasma exchange. When fibrinogen sieving coefficient was 0, selective plasma exchange reduced fibrinogen by approximately 10%. Scanning electron microscopy images revealed internal fouling of EC-4A's hollow fiber membrane by substances such as fibrinogen fibrils. Thus, fibrinogen reduction by selective plasma exchange may be predominantly caused by membrane fouling rather than filtration. © 2017 International Society for Apheresis, Japanese Society for Apheresis, and Japanese Society for Dialysis Therapy.

Savannah River reactor process water heat exchanger tube structural integrity margin Task Number 92-005-1

International Nuclear Information System (INIS)

Mertz, G.E.; Barnes, D.M.; Sindelar, R.L.

1992-02-01

Twelve process water heat exchangers are designed to remove heat generated in the reactor tank. Each heat exchanger has approximately 9000, 1/2 inch diameter x 0.049 inches thick tubes. Minimum structural tubing requirements and the leak rate through postulated tubing defects are developed in this report A comparison of the structural requirements and the defect size calculated to produce leak rates of 0.5 lbs./day demonstrate adequate structural margins against gross tube rupture. Commercial nuclear experience with pressurized water reactor (PWR) steam generator plugging criteria are used for guidance in performing this analysis. It is important to note that the SRS reactors are low energy systems with normal operating pressures of 203 psig at 130 degree F while the PWR is a high energy system with operating pressures near 2200 psig at 600 degree F. Clearly the PVM steam generator has loadings which are more severe than the SRS heat exchangers. Consistent with the Regulatory Guide 1.121 criteria both wastage (wall thinning) and cracking are addressed. Structural limits on wall thinning and crack size are developed to preclude gross rupture. ASME Section XI criteria, with the factors of safety recommended by Regulatory Guide 1.121 are used to develop the allowable crack size criteria. Normal operating conditions (pressure, dead weight, and hydraulic drag) are considered with seismic and water hammer accident conditions. Both the wall thinning and crack size criteria are developed for the end-of-evaluation period. Allowances for corrosion, wear, or crack growth have not been included in this analysis Structurally, the tubing is over designed and can tolerate large defects with adequate margins against gross rupture. The structural margins of heat exchanger tubing are evident by contrasting the tubing's structural capacity, per the ASME Code, with its operating conditions/configuration

Technical aspects of atomic and molecular data processing and exchange, 20. meeting of the A+M Data Centres and ALADDIN Network. Summary report of an IAEA technical meeting

International Nuclear Information System (INIS)

Humbert, D.; Braams, B.J.

2010-01-01

The proceedings of the IAEA Advisory Group Meeting on Technical Aspects of Atomic and Molecular Data Processing and Exchange (20th Meeting of A+M Data Centres Network), 7-9 September 2009 at IAEA Headquarters in Vienna, are summarized. The meeting conclusions and recommendations on priorities in A+M data compilation and evaluation and on technical aspects of data processing and exchange are also presented. (author)

Catalyst for hydrogen-amine D exchange

International Nuclear Information System (INIS)

Holtslander, W.J.; Johnson, R.E.

1976-01-01

A process is claimed for deuterium isotopic enrichment (suitable for use in heavy water production) by amine-hydrogen exchange in which the exchange catalyst comprises a mixture of alkyl amides of two metals selected from the group consisting of the alkali metals. Catalyst mixtures comprising at least one of the alkali amides of lithium and potassium are preferred. At least one of the following benefits are obtained: decreased hydride formation, decreased thermal decomposition of alkyl amide, increased catalyst solubility in the amine phase, and increased exchange efficiency. 11 claims

Adsorption on mixtures of ion exchangers

International Nuclear Information System (INIS)

Triolo, R.; Lietzke, M.H.

1979-01-01

A theoretical study has been made of adsorption on mixtures of ion exchangers. The effect of variables such as the concentration of the ion being adsorbed, the concentration of the supporting electrolyte, loading, the values of the capacities and equilibrium constants for the various exchange processes, and the fraction of each adsorber in the mixture on the observed distribution coefficient has been investigated. A computer program has been written to facilitate the calculation of distribution coefficients for the adsorption of an ion on a given mixture of ion exchangers under a specified set of conditions

Process and device for the extraction of ions from a clear liquid or one containing matter in suspension with a ion exchanger

International Nuclear Information System (INIS)

Capitani, Enzo; Teissie, Jean.

1982-01-01

Process for the continuous extraction of ions from a clear liquid or one containing matter in suspension by the use of a bed of ion exchange grains which is fluidized inside a column by circulation of the liquid, characterized by the fact that the said bed is subject to cyclic pulsations, in order to obtain sorting of the grains by density, the heavier grains having fixed the maximum ions. This invention can be applied for the continuous extraction of any type of anion or cation or exchangeable salt by means of resins or inorganic exchangers, to avoid clogging and abrasion problems, and to obtain maximum extraction rate and capacity. An example is given of the treatment of a suspension for the extraction of uranium [fr

EXPLOSION POTENTIAL ASSESSMENT OF HEAT EXCHANGER NETWORK AT THE PRELIMINARY DESIGN STAGE

Directory of Open Access Journals (Sweden)

MOHSIN PASHA

2016-07-01

Full Text Available The failure of Shell and Tube Heat Exchangers (STHE is being extensively observed in the chemical process industries. This failure can cause enormous production loss and have a potential of dangerous consequences such as an explosion, fire and toxic release scenarios. There is an urgent need for assessing the explosion potential of shell and tube heat exchanger at the preliminary design stage. In current work, inherent safety index based approach is used to resolve the highlighted issue. Inherent Safety Index for Shell and Tube Heat Exchanger (ISISTHE is a newly developed index for assessing the inherent safety level of a STHE at the preliminary design stage. This index is composed of preliminary design variables and integrated with the process design simulator (Aspen HYSYS. Process information can easily be transferred from process design simulator to MS Excel spreadsheet owing to this integration. This index could potentially facilitate the design engineer to analyse the worst heat exchanger in the heat exchanger network. Typical heat exchanger network of the steam reforming process is presented as a case study and the worst heat exchanger of this network has been identified. It is inferred from this analysis that shell and tube heat exchangers possess high operating pressure, corrected mean temperature difference (CMTD and flammability and reactive potential needs to be critically analysed at the preliminary design stage.

Effects of ionizing radiation on modern ion exchange materials

International Nuclear Information System (INIS)

Marsh, S.F.; Pillay, K.K.S.

1993-10-01

We review published studies of the effects of ionizing radiation on ion exchange materials, emphasizing those published in recent years. A brief overview is followed by a more detailed examination of recent developments. Our review includes styrene/divinylbenzene copolymers with cation-exchange or anion-exchange functional groups, polyvinylpyridine anion exchangers, chelating resins, multifunctional resins, and inorganic exchangers. In general, strong-acid cation exchange resins are more resistant to radiation than are strong-base anion exchange resins, and polyvinylpyridine resins are more resistant than polystyrene resins. Cross-linkage, salt form, moisture content, and the surrounding medium all affect the radiation stability of a specific exchanger. Inorganic exchangers usually, but not always, exhibit high radiation resistance. Liquid ion exchangers, which have been used so extensively in nuclear processing applications, also are included

Acetone and Water on TiO(110): H/D Exchange

International Nuclear Information System (INIS)

Henderson, Michael A.

2005-01-01

Isotopic H/D exchange between coadsorbed acetone and water on the TiO(110) surface was examined using temperature programmed desorption (TPD) as a function of coverage and two surface pretreatments (oxidation and reduction). Coadsorbed acetone and water interact repulsively on reduced TiO(110) based on results from the companion paper to this study, with water exerting a greater influence in destabilizing acetone and acetone having only a nominal influence on water. Despite the repulsive interaction between these coadsorbates, about 0.02 ML of a 1 ML d6-acetone on the reduced surface exhibits H/D exchange with coadsorbed water, with the exchange occurring exclusively in the high temperature region of the d?-acetone TPD spectrum at ∼340 K. The effect was confirmed with combinations of d?-acetone and D?O. The extent of exchange decreased on the reduced surface with water coverages above ∼0.3 ML due to the ability of water to displace coadsorbed acetone from first layer sites to the multilayer. In contrast, the extent of exchange increased by a factor of 3 when the surface was pre-oxidized prior to coadsorption. In this case, there was no evidence for the negative influence of high water coverages on the extent of H/D exchange. Comparison of the TPD spectra from the exchange products (either d?- or d?-acetone depending on the coadsorption pairing) suggests that, in addition to the 340 K exchange process seen on the reduced surface, a second exchange process was observed on the oxidized surface at ∼390 K. In both cases (oxidized and reduced), desorption of the H/D exchange products appeared to be reaction limited and to involve the influence of OH/OD groups (or water formed during recombinative desorption of OH/OD groups) instead of molecularly adsorbed water. The 340 K exchange process is assigned to reaction at step sites and the 390 K exchange process is attributed to the influence of oxygen adatoms deposited during surface oxidation. The H/D exchange

Model Based Controller Design for a Shell and Tube Heat Exchanger

Directory of Open Access Journals (Sweden)

S. Nithya

2007-10-01

Full Text Available In all the process industries the process variables like flow, pressure, level and temperature are the main parameters that need to be controlled in both set point and load changes. The transfer of heat is one of the main important operation in the heat exchanger .The transfer of heat may be fluid to fluid, gas to gas i.e. in the same phase or the phase change can occur on either side of the heat exchanger. The control of heat exchanger is complex due to its nonlinear dynamics. For this nonlinear process of a heat exchanger the model is identified to be First Order plus Dead Time (FOPDT.The Internal Model Control (IMC is one of the model predictive control methods based on the predictive output of the process model. The conventional controller tuning is compared with IMC techniques and it found to be suitable for heat exchanger than the conventional PI tuning.

Chromate ion-exchange study for cooling water

International Nuclear Information System (INIS)

Sengupta, A.K.

1985-01-01

In spite of high chromate selectivity, the ion-exchange process for Cr(IV) recovery from cooling tower blowdown is yet to be commercially popular. Possible degradation of the ion-exchange resin by the oxidative action of Cr(IV) during ion exchange has been considered as the prime obstacle. Resins have been manufactured with fairly acceptable properties to withstand both physical attrition and chemical oxidation. Demonstrated during the course of this research is early, gradual Cr(VI) breakthrough during fixed-bed column runs at acidic pH in the presence of competing sulfate and chloride anions. The advantage of high chromate selectivity is essentially lost due to the early Cr(VI) breakthrough because the column runs are always terminated after a pre-determined level of Cr(VI) has appeared in the treated water. Experimental results provide sufficient evidence that this is not due to poor column kinetics or electrolyte penetration. The chromate ion-exchange mechanism has been investigated in order to explain the foregoing anomalies for the chromate-exchange process. The knowledge of chromate ion-exchange mechanism has been used to overcome the shortcoming of gradual Cr(VI) breakthrough. This study shows that: (a) a continuous counter-current ion-exchange system theoretically offers much higher Cr(VI) removal capacity compared to conventional single-unit fixed-bed system for any pre-determined level of Cr(VI) breakthrough; (b) by modifying the resin composition, the gradual Cr(VI) breakthrough can be greatly eliminated

Proceedings of the Efficient Separations and Processing Cross-Cutting Program Annual Technical Exchange Meeting

International Nuclear Information System (INIS)

1995-01-01

This document contains summaries of technology development presented at the 1995 Efficient Separations and Processing Cross-Cutting Program (ESP) Annual Technical Exchange Meeting. The ESP is sponsored by the US Department of Energy's Office of Environmental Management (EM), Office of Technology Development. The meeting is held annually to promote a free exchange of ideas among technology developers, potential users (for example, EM focus areas), and other interested parties within EM. During this meeting, developers of ESP-funded technologies describe the problems and needs addressed by their technologies; the technical approach, accomplishments, and resolution of issues; the strategy and schedule for commercialization; and evolving potential applications. Presenters are asked to address the following areas: Target waste management problem, waste stream, or data need; scientific background and technical approach; technical accomplishments and resolution of technical issues; schedule and strategy for commercializing and implementing the technology or acquiring needed data; potential alternate applications of the technology or data, including outside of DOE/EM. The meeting is not a program review of the individual tasks or subtasks; but instead focuses on the technical aspects and implementation of ESP-sponsored technology or data. The meeting is also attended by members of the ESP Technical Review Team, who have the opportunity at that time to review the ESP as a whole

Isotopic exchange of cyclic ethers with deuterium over metal catalysts

International Nuclear Information System (INIS)

Duchet, J.C.; Cornet, D.

1976-01-01

The exchange reaction between deuterium and cyclic ethers (oxolane and α-methyl derivatives) has been investigated using rhodium and palladium catalysts. The first hydrogen undergoing exchange has been found to be located on a β-carbon. This fact, and the poisoning of the exchange of cyclopentane in the presence of ether, suggest that the O atom participates in the exchange mechanism of ethers. It appears, however, that the oxygen--metal bonding occurs only during this simple exchange process; simultaneous adsorption of oxygen and a vicinal carbon causes hydrogenolysis of the O--C bond. In each case multiple exchange is important. In the oxolane molecule two sets of exchangeable hydrogens are distinguished according to their reactivities, as could be expected by analogy with cycloalkanes. However, this distinction is not so clear in the exchange patterns of substituted oxolanes, since intermediate maxima are observed in these cases. It is suggested that the conformational properties of the substituted rings cause a constraint in the formation of 3,4-diadsorbed oxolanes. Thus, multiple exchange, based on α,β-process, and epimerization via the ''roll-over'' mechanism occur preferentially in certain parts of the molecules

Technical aspects of atomic and molecular data processing and exchange. 19. meeting of the A+M Data Centres and ALADDIN Network. Summary report of an IAEA technical meeting

International Nuclear Information System (INIS)

Humbert, D.

2008-05-01

The proceedings of the IAEA Technical Meeting on Technical Aspects of Atomic and Molecular Data Processing and Exchange (19th Meeting of A+M Data Centres and ALADDIN Network), held on 3-5 October, 2007 in Vienna, Austria, are briefly described. Conclusions and recommendations are presented concerning various proposed projects and their priorities involving A+M data compilation and evaluation and technical aspects of data processing, exchange, and distribution. (author)

IAEA advisory group meeting on technical aspects of atomic and molecular data processing and exchange (16. meeting of the A+M Data Centres and ALADDIN network). Summary report

Energy Technology Data Exchange (ETDEWEB)

Stephens, J A [ed.

2001-12-01

The proceedings of the IAEA Advisory group meeting on technical aspects of atomic and molecular data processing and exchange (16. meeting of A+M Data centers and ALADDIN Network), held on September 10-11, 2001 in Vienna, Austria are briefly described. The meeting conclusions and recommendations on the priorities in A+M data compilation and evaluation, and on the technical aspects of data processing, exchange and distribution are also presented. (author)

Secondary heat exchanger design and comparison for advanced high temperature reactor

International Nuclear Information System (INIS)

Sabharwall, P.; Kim, E. S.; Siahpush, A.; McKellar, M.; Patterson, M.

2012-01-01

Next generation nuclear reactors such as the advanced high temperature reactor (AHTR) are designed to increase energy efficiency in the production of electricity and provide high temperature heat for industrial processes. The efficient transfer of energy for industrial applications depends on the ability to incorporate effective heat exchangers between the nuclear heat transport system and the industrial process heat transport system. This study considers two different types of heat exchangers - helical coiled heat exchanger and printed circuit heat exchanger - as possible options for the AHTR secondary heat exchangers with distributed load analysis and comparison. Comparison is provided for all different cases along with challenges and recommendations. (authors)

Inorganic ion exchange evaluation and design: Silicotitanate ion exchange waste conversion

International Nuclear Information System (INIS)

Balmer, M.L.; Bunker, B.C.

1995-03-01

Ion exchange materials are being evaluated for removing Cs, SR from tank waste. Thermal conversion of a variety of compositions within the Cs 2 O-TiO 2 -SiO 2 phase diagram yielded both glass and crystalline materials, some of which show low leach rates and negligible Cs losses during heat treatment. A new material, CsTiSi 2 0 6 , with a structure isomorphous to pollucite (CsAlSi 2 0 6 ) has been identified. This material represents a new class of crystalline zeolite materials which contain large amounts of titanium. Direct conversion of Cs loaded silicotitanate ion exchangers to CsTiSi 2 O 6 is an excellent alternative to dissolving the Cs-loaded or Cs-eluted exchangers in borosilicate glass because: CsTiSi 2 O 6 is formed using a simple, one step heat treatment. The unique crystalline pollucite-like structure of CsTiSi 2 O 6 traps Cs, and exhibits extremely low Cs leach rates. CsTiSi 2 O 6 is converted to solid waste at a low processing temperature of 700 to 800 C (nominal melter operating temperatures are 1150 C). CsTiSi 2 0 6 concentrates the waste, thus generating lower volumes of expensive HLW. Cs losses due to volatilization during processing of CsTiSi 2 O 6 are extremely low

Tritium separation factors in distillation and chemical exchange processes

International Nuclear Information System (INIS)

Dave, S.M.; Ghosh, S.K.; Sadhukhan, H.K.

1982-01-01

The vapour pressures of different isotopic hydrogen, water and ammonia molecules have been calculated. These vapour pressures can be used to evaluate relative volatilities of different species for separation of tritium isotopes by distillation. The equilibrium constants for various exchange reactions involving different deuterated and tritiated species of hydrogen, water and ammonia molecules have also been calculated for different temperatures. (author)

Biodegradation of ion-exchange media

International Nuclear Information System (INIS)

Bowerman, B.S.; Clinton, J.H.; Cowdery, S.R.

1988-08-01

Ion-exchange media, both bead resins and powdered filter media, are used in nuclear power plants to remove radioactivity from process water prior to reuse or environmental discharge. Since the ion- exchange media are made from synthetic hydrocarbon-based polymers, they may be susceptible to damage from biological activity. The purpose of this study was to investigate some of the more basic aspects of biodegradation of ion-exchange media, specifically to evaluate the ability of microorganisms to utilize the ion-exchange media or materials sorbed on them as a food source. The ASTM-G22 test, alone and combined with the Bartha Pramer respirometric method, failed to indicate the biodegradability of the ion-exchange media. The limitation of these methods was that they used a single test organism. In later phases of this study, a mixed microbial culture was grown from resin waste samples obtained from the BNL High Flux Beam Reactor. These microorganisms were used to evaluate the susceptibility of different types of ion-exchange media to biological attack. Qualitative assessments of biodegradability were based on visual observations of culture growths. Greater susceptibility was associated with increased turbidity in solution indicative of bacterial growth, and more luxuriant fungal mycelial growth in solution or directly on the ion-exchange resin beads. 21 refs., 9 figs., 18 tabs

A qualitative study of sign-out processes between primary and on-call residents: relationships in information exchange, responsibility and accountability.

Science.gov (United States)

Lee, Soo-Hoon; Fisher, Dale A; Mah, Heidi; Goh, Wei-Ping; Phan, Phillip H

2017-10-01

To review a quality improvement event on the process of sign-outs between the primary and on-call residents. A retrospective qualitative study using semi-structured interviews. A tertiary academic medical center in Singapore with 283 inpatient Medicine beds served by 28 consultants, 29 registrars, 45 residents and 30 interns during the day but 5 residents and 3 interns at night. Residents, registrars and consultants. Quality improvement event on sign-out. Effectiveness of sign-out comprises exchange of patient information, professional responsibility and task accountability. The following process of sign-outs was noted. Primary teams were accountable to the on-call resident by selecting at-risk patients and preparing contingency plans for sign-out. Structured information exchanged included patient history, active problems and plans of care. On-call residents took ownership of at-risk patients by actively asking questions during sign-out and reporting back the agreed care plan. On-call residents were accountable to the primary team by reporting back at-risk patients the next day. A structured information exchange at sign-out increased the on-call resident's ability to care for at-risk patients when it was supported by two-way transfers of responsibility and accountability. © The Author 2017. Published by Oxford University Press in association with the International Society for Quality in Health Care. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Method of pyrolysis for spent ion-exchange resins

International Nuclear Information System (INIS)

Aoyama, Yoshiyuki; Matsuda, Masami; Kawamura, Fumio; Yusa, Hideo.

1985-01-01

Purpose: To prevent the generation of noxious sulfur oxide and ammonia on the pyrolysis for spent ion-exchange resins discharged from nuclear power plants. Method: In the case where the pyrolysis is made for the cationic exchange resins having sulfonic acids as the ion-exchange group, alkali metals or alkaline earth metals capable of reacting with sulfonic acid groups to form solid sulfates are previously deposited by way of ion-exchange reactions prior to the pyrolysis. In another case of the anionic exchange resins having quarternary ammonium groups as the ion-exchange groups, halogenic elements capable of reacting with the ammonium groups to form solid ammonium salts are deposited to the ion-exchange resins through ion-exchange reactions prior to the pyrolysis. As a result, the amount of the binders used can be reduced, and this method can be used in a relatively simple processing facility. (Horiuchi, T.)

Advantages of Chemical Exchange-Sensitive Spin-Lock (CESL) Over Saturation Transfer (CEST) for Hydroxyl- and Amine-Water Proton Exchange Studies

Science.gov (United States)

Jin, Tao; Kim, Seong-Gi

2014-01-01

The chemical exchange (CE) rate of endogenous hydroxyl and amine protons with water is often comparable to the difference in their chemical shifts. These intermediate exchange (IMEX) processes have been imaged by the CE saturation transfer (CEST) approach with low-power and long-duration irradiation. However, its sensitivity is not optimal, and more importantly, the signal is contaminated by slow magnetization transfer processes. Here, the property of CEST signals is compared to a CE-sensitive spin-locking (CESL) technique irradiating at the labile proton frequency. Firstly, using a higher power and shorter irradiation in CE-MRI yields i) increasing selectivity to faster chemical exchange rates by higher sensitivity to faster exchanges and less sensitivity to slower CE and magnetization transfer processes, and ii) decreasing in vivo asymmetric magnetization transfer contrast measured at ±15 ppm. The sensitivity gain of CESL over CEST is higher for a higher-power and shorter irradiation. Unlike CESL, CEST signals oscillate at a very high power and short irradiation. Secondly, time-dependent CEST and CESL signals are well modeled by analytical solutions of CE-MRI with asymmetric population approximation (CEAPA), which can be used for quantitative CE-MRI, and validated by simulations of Bloch-McConnell equations and phantom experiments. Lastly, in vivo amine-water proton exchange contrast measured at 2.5 ppm with ω1 of 500 Hz is 18% higher in sensitivity for CESL than CEST at 9.4 T. Overall, CESL provides better exchange rate selectivity and sensitivity than CEST; therefore, CESL is more suitable for CE-MRI of IMEX protons. PMID:25199631

Proceedings of the efficient separations and processing crosscutting program 1997 technical exchange meeting

Energy Technology Data Exchange (ETDEWEB)

Gephart, J.M. [ed.

1997-05-01

This document contains summaries of technology development presented at the 1997 Efficient Separations and Processing Crosscutting Program (ESP-CP) Technical Exchange Meeting (TEM), held January 28-30, 1997, in Gaithersburg, Maryland. The ESP-CP is sponsored by the U.S. Department of Energy`s Office of Environmental Management (DOE/EM), Office of Science and Technology. The ESP-CP TEM is held annually to: (1) Present current technology development activities funded by the ESP-CP. Developers of ESP-CP-funded technologies describe the problems and needs addressed by their technologies; the technical approach, accomplishments, and resolution of issues; the strategy and schedule for commercialization; and evolving potential applications. Representatives from DOE/EM`s Focus Areas also present their technology needs. (2) Promote the exchange of technical information among those developing new separations technologies, those responsible for providing new separations technologies to meet DOE/EM needs, and those who need or will potentially make use of such technologies. (3) Familiarize the ESP-CP Technical Review Team with the FY 1997 program and solicit reviewers` views on the program as a whole. This meeting is not a program review of the individual tasks, but instead focuses on the technical aspects and implementation of ESP-CP-sponsored technology or data. This document also contains a list of ESP-CP-sponsored publications, presentations, and patents. Separate abstracts have been indexed into the energy database for contributions to this proceedings.

Proceedings of the efficient separations and processing crosscutting program 1997 technical exchange meeting

International Nuclear Information System (INIS)

Gephart, J.M.

1997-01-01

This document contains summaries of technology development presented at the 1997 Efficient Separations and Processing Crosscutting Program (ESP-CP) Technical Exchange Meeting (TEM), held January 28-30, 1997, in Gaithersburg, Maryland. The ESP-CP is sponsored by the U.S. Department of Energy's Office of Environmental Management (DOE/EM), Office of Science and Technology. The ESP-CP TEM is held annually to: (1) Present current technology development activities funded by the ESP-CP. Developers of ESP-CP-funded technologies describe the problems and needs addressed by their technologies; the technical approach, accomplishments, and resolution of issues; the strategy and schedule for commercialization; and evolving potential applications. Representatives from DOE/EM's Focus Areas also present their technology needs. (2) Promote the exchange of technical information among those developing new separations technologies, those responsible for providing new separations technologies to meet DOE/EM needs, and those who need or will potentially make use of such technologies. (3) Familiarize the ESP-CP Technical Review Team with the FY 1997 program and solicit reviewers' views on the program as a whole. This meeting is not a program review of the individual tasks, but instead focuses on the technical aspects and implementation of ESP-CP-sponsored technology or data. This document also contains a list of ESP-CP-sponsored publications, presentations, and patents. Separate abstracts have been indexed into the energy database for contributions to this proceedings

Modeling of Crystalline Silicotitanate Ion Exchange Columns

International Nuclear Information System (INIS)

Walker, D.D.

1999-01-01

Non-elutable ion exchange is being considered as a potential replacement for the In-Tank Precipitation process for removing cesium from Savannah River Site (SRS) radioactive waste. Crystalline silicotitanate (CST) particles are the reference ion exchange medium for the process. A major factor in the construction cost of this process is the size of the ion exchange column required to meet product specifications for decontaminated waste. To validate SRS column sizing calculations, SRS subcontracted two reknowned experts in this field to perform similar calculations: Professor R. G. Anthony, Department of Chemical Engineering, Texas A ampersand 038;M University, and Professor S. W. Wang, Department of Chemical Engineering, Purdue University. The appendices of this document contain reports from the two subcontractors. Definition of the design problem came through several meetings and conference calls between the participants and SRS personnel over the past few months. This document summarizes the problem definition and results from the two reports

Factors contributing to troponin exchange in myofibrils and in solution.

Science.gov (United States)

She, M; Trimble, D; Yu, L C; Chalovich, J M

2000-01-01

The troponin complex in a muscle fiber can be replaced with exogenous troponin by using a gentle exchange procedure in which the actin-tropomyosin complex is never devoid of a full complement of troponin (Brenner et al. (1999) Biophys J 77: 2677-2691). The mechanism of this exchange process and the factors that influence this exchange are poorly understood. In this study, the exchange process has now been examined in myofibrils and in solution. In myofibrils under rigor conditions, troponin exchange occurred preferentially in the region of overlap between actin and myosin when the free Ca2+ concentration was low. At higher concentrations of Ca2+, the exchange occurred uniformly along the actin. Ca2+ also accelerated troponin exchange in solution but the effect of S1 could not be confirmed in solution experiments. The rate of exchange in solution was insensitive to moderate changes in pH or ionic strength. Increasing the temperature resulted in a two-fold increase in rate with each 10 degrees C increase in temperature. A sequential two step model of troponin binding to actin-tropomyosin could simulate the observed association and dissociation transients. In the absence of Ca2+ or rigor S1, the following rate constants could describe the binding process: k1 = 7.12 microM(-1) s(-1), k(-1) = 0.65 s(-1), k2 = 0.07 s(-1), k(-2) = 0.0014 s(-1). The slow rate of detachment of troponin from actin (k(-2)) limits the rate of exchange in solution and most likely contributes to the slow rate of exchange in fibers.

Two-phase exchangers with small temperature differences

International Nuclear Information System (INIS)

Moracchioli, R.; Marie, G.; Lallee, J. de.

1976-01-01

The possibility in using heat available at low temperature level is shown (industrial wastes, solar energy, geothermal energy, heat power from seas). Special emphasis is put on the importance of heat exchangers that commonly should be evaporators and condensors working with small temperature differences (20 to 100 deg C). The expansion of the so-called ''new'' energies or recovery processes will depend on the physical performance of exchangers (Rankine two-phase cycles) and cost of the elementary exchange interfaces and assembling technics [fr

IAEA advisory group meeting on technical aspects of atomic and molecular data processing and exchange (15. meeting of the A+M data centres and ALADDIN network). Summary report

International Nuclear Information System (INIS)

Stephens, J.A.

1999-12-01

The proceedings of the IAEA Advisory Group Meeting on 'Technical Aspects of Atomic and Molecular Data Processing and Exchange' (15th Meeting of A+M Data Centres and ALADDIN Network), held on September 13-14, 1999 in Vienna, Austria are briefly described. The meeting conclusions and recommendations on the priorities in A+M data compilation and evaluation, and on the technical aspects of data processing, exchange, and distribution are also presented. (author)

An evaluation of solution algorithms and numerical approximation methods for modeling an ion exchange process

Science.gov (United States)

Bu, Sunyoung; Huang, Jingfang; Boyer, Treavor H.; Miller, Cass T.

2010-07-01

The focus of this work is on the modeling of an ion exchange process that occurs in drinking water treatment applications. The model formulation consists of a two-scale model in which a set of microscale diffusion equations representing ion exchange resin particles that vary in size and age are coupled through a boundary condition with a macroscopic ordinary differential equation (ODE), which represents the concentration of a species in a well-mixed reactor. We introduce a new age-averaged model (AAM) that averages all ion exchange particle ages for a given size particle to avoid the expensive Monte-Carlo simulation associated with previous modeling applications. We discuss two different numerical schemes to approximate both the original Monte-Carlo algorithm and the new AAM for this two-scale problem. The first scheme is based on the finite element formulation in space coupled with an existing backward difference formula-based ODE solver in time. The second scheme uses an integral equation based Krylov deferred correction (KDC) method and a fast elliptic solver (FES) for the resulting elliptic equations. Numerical results are presented to validate the new AAM algorithm, which is also shown to be more computationally efficient than the original Monte-Carlo algorithm. We also demonstrate that the higher order KDC scheme is more efficient than the traditional finite element solution approach and this advantage becomes increasingly important as the desired accuracy of the solution increases. We also discuss issues of smoothness, which affect the efficiency of the KDC-FES approach, and outline additional algorithmic changes that would further improve the efficiency of these developing methods for a wide range of applications.

EXPERIMENTAL STUDY OF LOCAL HYDRODYNAMICS AND MASS EXCHANGE PROCESSES OF COOLANT IN FUEL ASSEMBLIES OF PRESSURIZED WATER REACTORS

Directory of Open Access Journals (Sweden)

S. M. Dmitriev

2016-01-01

Full Text Available The results of experimental studies of local hydrodynamics and mass exchange of coolant flow behind spacer and mixing grids of different structural versions that were developed for fuel assemblies of domestic and foreign nuclear reactors are presented in the article. In order to carry out the study the models of the following fuel assemblies have been fabricated: FA for VVER and VBER, FA-KVADRAT for PWR-reactor and FA for KLT-40C reactor. All the models have been fabricated with a full geometrical similarity with full-scale fuel assemblies. The study was carried out by simulating the flow of coolant in a core by air on an aerodynamic test rig. In order to measure local hydrodynamic characteristics of coolant flow five-channel Pitot probes were used that enable to measure the velocity vector in a point by its three components. The tracerpropane method was used for studying mass transfer processes. Flow hydrodynamics was studied by measuring cross-section velocities of coolant flow and coolant rates according to the model cells. The investigation of mass exchange processes consisted of a study of concentration distribution for tracer in experimental model, in determination of attenuation lengths of mass transfer processes behind mixing grids, in calculating of inter-cellar mass exchange coefficient. The database on coolant flow in fuel assemblies for different types of reactors had been accumulated that formed the basis of the engineering substantiation of reactor cores designs. The recommendations on choice of optimal versions of mixing grids have been taken into consideration by implementers of the JSC “OKBM Afrikantov” when creating commissioned fuel assemblies. The results of the study are used for verification of CFD-codes and CFD programs of detailed cell-by-cell calculation of reactor cores in order to decrease conservatism for substantiation of thermal-mechanical reliability.

Mathematical model development of heat and mass exchange processes in the outdoor swimming pool

Directory of Open Access Journals (Sweden)

M. V. Shaptala

2014-12-01

Full Text Available Purpose. Currently exploitation of outdoor swimming pools is often not cost-effective and, despite of their relevance, such pools are closed in large quantities. At this time there is no the whole mathematical model which would allow assessing qualitatively the effect of energy-saving measures. The aim of this work is to develop a mathematical model of heat and mass exchange processes for calculating basic heat and mass losses that occur during its exploitation. Methodology. The method for determination of heat and mass loses based on the theory of similarity criteria equations is used. Findings. The main types of heat and mass losses of outdoor pool were analyzed. The most significant types were allocated and mathematically described. Namely: by evaporation of water from the surface of the pool, by natural and forced convection, by radiation to the environment, heat consumption for water heating. Originality. The mathematical model of heat and mass exchange process of the outdoor swimming pool was developed, which allows calculating the basic heat and mass loses that occur during its exploitation. Practical value. The method of determining heat and mass loses of outdoor swimming pool as a software system was developed and implemented. It is based on the mathematical model proposed by the authors. This method can be used for the conceptual design of energy-efficient structures of outdoor pools, to assess their use of energy-intensive and selecting the optimum energy-saving measures. A further step in research in this area is the experimental validation of the method of calculation of heat losses in outdoor swimming pools with its use as an example the pool of Dnipropetrovsk National University of Railway Transport named after Academician V. Lazaryan. The outdoor pool, with water heating- up from the boiler room of the university, is operated year-round.

The PILO process: zeolites and titanates in the treatment of spent ion exchange resins

International Nuclear Information System (INIS)

Hultgren, Aa.; Thegerstroem, C.; Forberg, S.; Westermark, T.; Faelt, L.

1981-01-01

Spent ion exchange resins from power reactor operation contain more than 95% of the total radioactivity of wet reactor wastes. Cementation and bituminization are the two methods applied in Sweden up to now for the immobilization of spent resins. Over the last years, however, research and development work has resulted in a proposed process (PILO), where > 99.9 % of cesium and strontium and around 90 % of other radioactive nuclides are eluted from the spent resins and sorbed in zeolites and titanates in a chromatographic process. The inorganic sorbents are dried after loading and sintered to yield long-term stable products, while the treated resins may be incinerated to give ash residues of fairly short-lived activity. The development work has included production, characterization and testing of different zeolites and titanates, bench-scale optimization of the chromatographic process using actual spent resins, heat treatment of the loaded inorganic sorbents, and resin incineration. Over-all system design studies including transport requirements, integrated process flowsheets, and cost estimates are now in progress. The aim is to have a sufficient basis during spring 1982 to decide on the merits of a PILO plant at the planned repository for low and medium level waste (SFR), to be commissioned in 1988. (Auth.)

Oxygen isotope exchange on palladium catalysts

International Nuclear Information System (INIS)

Kravchuk, L.S.; Beschetvertnaya, T.I.; Novorodskij, V.G.; Novikova, M.G.; Zaretskij, M.V.; Valieva, S.V.

1983-01-01

Oxygen heteromolecular isotope exchange on unreduced palladium catalysts, distingushing by metal content is studied. Content of 18 O in gaseous phase is eoual to 46%. Calculations of heteroexchange rates are conducted with decrease of the 18 O in the gaseous phase over solid sample. Method of oxygen thermodesorption has been used to establish that palladium, deposited on γ-Al 2 O 3 during exchange process is in oxidized state; in this case strength of Pd-O bond is determined by content dispersity) of the metal. It is shown that significant increase of exchange rate on the samples with Pd >> 0.5 mass.% content can be induced as by side decomposition reaction of its oxide and corresponding dilution of gaseous mixture by ''light'' oxygen so by possibility of exchange with oxygen of PdO phase

Lipid exchange by ultracentrifugation

DEFF Research Database (Denmark)

Drachmann, Nikolaj Düring; Olesen, Claus

2014-01-01

, and the complex interplay between the lipids and the P-type ATPases are still not well understood. We here describe a robust method to exchange the majority of the lipids surrounding the ATPase after solubilisation and/or purification with a target lipid of interest. The method is based on an ultracentrifugation...... step, where the protein sample is spun through a dense buffer containing large excess of the target lipid, which results in an approximately 80-85 % lipid exchange. The method is a very gently technique that maintains protein folding during the process, hence allowing further characterization...

Near-infrared spectroscopic observation of the ageing process in archaeological wood using a deuterium exchange method.

Science.gov (United States)

Tsuchikawa, Satoru; Yonenobu, Hitoshi; Siesler, H W

2005-03-01

The ageing degradation of the fine wood structure of dry-exposed archaeological wood was investigated by Fourier transform near-infrared spectroscopy with the aid of a deuterium exchange method. The archaeological wood sample was taken from an old wooden temple in Japan (late 7th century), which has been designated as a UNESCO world heritage site. Comparing the analytical results with those of a modern wood sample of the same species, the ageing process of archaeological wood was clarified as a change in the state of order on a macromolecular structural level. It can be concluded from NIR spectra that the amorphous region, and partially semi-crystalline region, in cellulose, hemicellulose, and lignin decreased by the ageing degradation, whereas the crystalline region in cellulose was not affected by the ageing. The accessibility of the diffusant to effect H/D-exchange was monitored by an OH-related absorption band obtained from FT-NIR transmission spectroscopy and characteristically varied with the ageing process of the wood samples, the absorption bands characteristic of a specific state of order and the diffusion agent. Finally, we proposed a morphological model to describe the variation of the fine structure of the microfibrils in the cell wall with ageing degradation. The state of microfibrils changed loosely by ageing, so that elementary fibrils were arranged loosely under 5 A, whereas several elementary fibrils in the modern wood were arranged in very close proximity under 3 A to each other.

Determination of Ground Heat Exchangers Temperature Field in Geothermal Heat Pumps

Science.gov (United States)

Zhurmilova, I.; Shtym, A.

2017-11-01

For the heating and cooling supply of buildings and constructions geothermal heat pumps using low-potential ground energy are applied by means of ground exchangers. The process of heat transfer in a system of ground exchangers is a phenomenon of complex heat transfer. The paper presents a mathematical modeling of heat exchange processes, the temperature fields are built which are necessary for the determination of the ground array that ensures an adequate supply of low potential energy excluding the freezing of soil around the pipes in the ground heat exchangers and guaranteeing a reliable operation of geothermal heat pumps.

77 FR 10026 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing of...

Science.gov (United States)

2012-02-21

... Substance of the Proposed Rule Change The Exchange is proposing to amend its complex order processing rules... Exchange notes that at least one other options exchange that offers electronic complex order processing... simplify the rule text. In addition, the Exchange is proposing certain changes to simplify the definitions...

Continued evaluation of compact heat exchangers for OTEC evaluation. Final report

Energy Technology Data Exchange (ETDEWEB)

McGowan, J.G.

1979-10-01

The objectives of this work investigating the applicability of compact plate heat type heat exchangers to OTEC power systems were: (1) an analytical and experimental evaluation of the performance characteristics of compact heat exchangers using ammonia as the working fluid operating under the entire range of OTEC system conditions; and (2) an evaluation of the applicable manufacturing processes, maintenance requirements, and arrangement concepts for large-scale compact OTEC heat exchangers with specific emphasis on total economics. The work was carried out to establish the applicability of compact plate type heat exchangers to OTEC power systems and to provide: (1) experimental verification of predicted performance (heat transfer and fluid flow) under OTEC operating conditions (using NH/sub 3/); (2) provide initial performance data for several desirable plate type OTEC heat exchanger panels; (3) provide test apparatus for continued experimental testing of OTEC compact heat exchanger panels; and (4) provide design information on applicable manufacturing processes maintenance requirements and arrangement concepts for plate type heat exchangers.

Construction Operations Building Information Exchange (COBIE)

Science.gov (United States)

2007-06-01

Swalley U.S. Department of State, Overseas Buildings Operations Toby Wilson U.S. Army, Corps of Engineers, Engineer R&D Center Jeff Wix AEC3 The...exchanged in COBIE. To map those information exchanges to the IFC model, the Information Delivery Manual (IDM) process [ Wix 2007] was also used. The...Folksonomy. Wikimedia Foundation. http://en.wikipedia.org/wiki/Folksonomy/, accessed 3 August 2007. Wix , Jeffrey. 2007. Information Delivery Manual

Heat exchangers

Energy Technology Data Exchange (ETDEWEB)

Schmidt, E L; Eisenmann, G; Hahne, E [Stuttgart Univ. (TH) (F.R. Germany). Inst. fuer Thermodynamik und Waermetechnik

1976-04-01

A survey is presented on publications on design, heat transfer, form factors, free convection, evaporation processes, cooling towers, condensation, annular gap, cross-flowed cylinders, axial flow through a bundle of tubes, roughnesses, convective heat transfer, loss of pressure, radiative heat transfer, finned surfaces, spiral heat exchangers, curved pipes, regeneraters, heat pipes, heat carriers, scaling, heat recovery systems, materials selection, strength calculation, control, instabilities, automation of circuits, operational problems and optimization.

Development of heat exchangers for nuclear service

International Nuclear Information System (INIS)

Hodge, R.I.; Dalrymple, D.G.

1976-01-01

Unusual design constraints, due to tube vibration, are called for when tube-in-shell heat exchangers are incorporated into CANDU type reactor power plants. CRNL has programs studying tube excitation and response, flow conditions, and the fretting process in such exchangers, tube plugging techniques, and eddy current scanning systems for inside bores of full-length tubes. (E.C.B.)

Report on process design studies of a tritium recovery process using dual temperature exchange with metal hydrides

International Nuclear Information System (INIS)

Benenati, R.F.

1976-01-01

Studies were made of the process characteristics of a plant to decontaminate tritiated water using dual temperature exchange with VH 2 . Feed to the plant consists of 300 kg/day on water containing 1 Ci/kg of tritium. A reference design was developed based on a decontamination factor of 10 2 and 10 kg/day of enriched product. This design requires a total of 48 ideal separation stages, 22 stages in the enriching section and 26 stages in the stripping section. Only low grade heat is required for the heating cycle and a relatively small (12 ton) ice machine is required for the cooling cycle. A total plant inventory of approximately 10 tons VH 2 is required. A mechanical design of the dual temperature stage complete with all heat transfer surfaces and flow diverters was devised and modeled. Since the process involves periodic swings in temperature between 0 and 60 0 C, a substantial portion of the operation is expected to be in unsteady state transition from one state to another. A two-step experimental program has been presented: the first step consists of a single stage unit, i.e., one hot bed and one cold bed operating in a simple closed loop. The second stage in the experimental program would consist of five stages operating as a small cascade

Wherever I may roam: Processes of self-esteem development from adolescence to emerging adulthood in the context of international student exchange.

Science.gov (United States)

Hutteman, Roos; Nestler, Steffen; Wagner, Jenny; Egloff, Boris; Back, Mitja D

2015-05-01

Previous studies on self-esteem development show substantial changes as well as interindividual differences in change from adolescence to young adulthood. However, the processes underlying these developmental trajectories are still not well understood. The aim of the present study was to shed light on the macro- and microprocesses of self-esteem development. We investigated a sample of 876 German high school students (M = 16.0 years at Time 1) participating in an international exchange year. Exchange students provided 3 waves of trait self-esteem data (shortly before they departed, immediately after return, and 1 year later), as well as 9 monthly state measures of self-esteem and social inclusion during their stay abroad. In addition, a control group of high school students who stayed in Germany (N = 714) provided 2 waves of trait self-esteem data. From a macroperspective, results showed an effect of student exchange on trait self-esteem development: Exchange students showed a steeper mean-level increase and a lower rank-order stability compared with control students. Zooming in on the microprocesses underlying these developmental patterns, we found trait changes in exchange students to be mediated by state changes in self-esteem during their exchange. These fluctuations in state self-esteem were found to be predicted by feelings of social inclusion in the host country, and vice versa, providing support for both sociometer and self-broadcasting perspectives on self-esteem dynamics. In sum, our findings emphasize the importance of incorporating a microanalytical approach when investigating self-esteem development by showing that the environment triggers changes in this relatively stable personality trait through changes in states. (c) 2015 APA, all rights reserved).

Ion-exchange equilibrium of N-acetyl-D-neuraminic acid on a strong anionic exchanger.

Science.gov (United States)

Wu, Jinglan; Ke, Xu; Zhang, Xudong; Zhuang, Wei; Zhou, Jingwei; Ying, Hanjie

2015-09-15

N-acetyl-D-neuraminic acid (Neu5Ac) is a high value-added product widely applied in the food industry. A suitable equilibrium model is required for purification of Neu5Ac based on ion-exchange chromatography. Hence, the equilibrium uptake of Neu5Ac on a strong anion exchanger, AD-1 was investigated experimentally and theoretically. The uptake of Neu5Ac by the hydroxyl form of the resin occurred primarily by a stoichiometric exchange of Neu5Ac(-) and OH(-). The experimental data showed that the selectivity coefficient for the exchange of Neu5Ac(-) with OH(-) was a non-constant quantity. Subsequently, the Saunders' model, which took into account the dissociation reactions of Neu5Ac and the condition of electroneutrality, was used to correlate the Neu5Ac sorption isotherms at various solution pHs and Neu5Ac concentrations. The model provided an excellent fit to the binary exchange data for Cl(-)/OH(-) and Neu5Ac(-)/OH(-), and an approximate prediction of equilibrium in the ternary system Cl(-)/Neu5Ac(-)/OH(-). This basic information combined with the general mass transfer model could lay the foundation for the prediction of dynamic behavior of fixed bed separation process afterwards. Copyright © 2015 Elsevier Ltd. All rights reserved.

Exergy analysis of the biogas sorption-enhanced chemical looping reforming process integrated with a high-temperature proton exchange membrane fuel cell

International Nuclear Information System (INIS)

Kasemanand, Sarunyou; Im-orb, Karittha; Tippawan, Phanicha; Wiyaratn, Wisitsree; Arpornwichanop, Amornchai

2017-01-01

Highlights: • A biogas reforming and fuel cell integrated process is considered. • Energy and exergy analyses of the integrated process are performed. • Increasing the nickel oxide-to-biogas ratio decreases the exergy efficiency. • The exergy destruction of the fuel cell increases with increasing cell temperature. • The exergy efficiency of the process is improved when heat integration is applied. - Abstract: A biogas sorption-enhanced chemical looping reforming process integrated with a high-temperature proton exchange membrane fuel cell is analyzed. Modeling of such an integrated process is performed by using a flowsheet simulator (Aspen plus). The exergy analysis is performed to evaluate the energy utilization efficiency of each unit and that of the integrated process. The effect of steam and nickel oxide to biogas ratios on the exergetic performance of the stand-alone biogas sorption-enhanced chemical looping reforming process is investigated. The total exergy destruction increases as the steam or nickel oxide to biogas ratio increases. The main exergy destruction is found at the air reactor. For the high-temperature proton exchange membrane fuel cell, the main exergy destruction is found at the cathode. The total exergy destruction increases when cell temperature increases, whereas the inverse effect is found when the current density is considered as a key parameter. Regarding the exergy efficiency, the results show opposite trend to the exergy destruction. The heat integration analysis is performed to improve the exergetic performance. It is found that the integrated process including the heat integration system can improve the exergy destruction and exergy efficiency of 48% and 60%, respectively.

Summary report of IAEA technical meeting on technical aspects of atomic and molecular data processing and exchange - 18th meeting of the A+M Data Centres and ALADDIN Network

International Nuclear Information System (INIS)

Hubert, D.

2006-01-01

The IAEA Technical Meeting on 'Technical Aspects of Atomic and Molecular Data Processing and Exchange - 18th Meeting of A+M Data Centres and ALADDIN Network' was held on 10-11 October 2005, in Vienna, Austria. The discussions and presentations focused on the priorities in A+M data compilation and evaluation, and are summarized in this report. Conclusions and recommendations on the technical aspects of data processing, exchange and distribution are also presented. (author)

Measurement of cation exchange capacity (CEC) on natural zeolite by percolation method

Science.gov (United States)

Wiyantoko, Bayu; Rahmah, Nafisa

2017-12-01

The cation exchange capacity (CEC)measurement has been carried out in natural zeolite by percolation method. The natural zeolite samples used for cation exchange capacity measurement were activated beforehand with physical activation and chemical activation. The physically activated zeolite was done by calcination process at 600 °C for 4 hours. The natural zeolite was activated chemically by using sodium hydroxide by refluxing process at 60-80 °C for 3 hours. In summary, cation exchange capacity (CEC) determination was performed by percolation, distillation and titration processes. Based on the measurement that has been done, the exchange rate results from physical activated and chemical activated of natural zeolite were 181.90cmol (+)/kg and 901.49cmol (+)/kg respectively.

Chemical exchange equilibria in isotope separation. Part I : Evaluation of separation factors

International Nuclear Information System (INIS)

Dave, S.M.

1980-01-01

The theory of chemical exchange equilibria as applied to the isotope separation processes and the isotope effects on equilibrium constants of different exchange reactions has come a long way since its inception by Urey and Rittenberg. An attempt has been made to bring relevant information together and present a unified approach to isotopic chemical exchange equilibrium constant evaluation and its implications to separation processes. (auth.)

Chaotic spin exchange: is the spin non-flip rate observable?

International Nuclear Information System (INIS)

Senba, Masayoshi

1994-01-01

If spin exchange is of the Poisson nature, that is, if the time distribution of collisions obeys an exponential distribution function and the collision process is random, the muon spin depolarization is determined only by the spin flip rate regardless of the spin non-flip rate. In this work, spin exchange is discussed in the case of chaotic spin exchange, where the distribution of collision time sequences, generated by a deterministic equation, is exponential but not random (deterministic chaos). Even though this process has the same time distribution as a Poisson process, the muon polarization is affected by the spin non-flip rate. Having an exponential time distribution function is not a sufficient condition for the non-observation of the spin non-flip rate and it is essential that the process is also random. (orig.)

Standardized structure of electronic records for information exchange

International Nuclear Information System (INIS)

Galabova, Sevdalina; Trencheva, Tereza; Trenchev, Ivan

2009-01-01

In the paper is presented the structure of the electronic record whose form is standardized in ISO 2709:2008. This International Standard describes a generalized structure, a framework designed specially for communications between data processing systems and not for use as a processing format within systems.Basic terms are defined as follows: character, data field, directory, directory map, field, field separator etc. It’s presented the general structure of a record. The application analysis of this structure shows the effective information exchange in the widest range.The purpose of this research is to find out advantages and structure of the information exchange format standardized in ISO 2709:2008. Key words: Standardized structure, electronic records, exchange formats, data field, directory, directory map, indicators, identifiers

Damping in heat exchanger tube bundles. A review

International Nuclear Information System (INIS)

Iqbal, Qamar; Khushnood, Shahab; Ghalban, Ali Roheim El; Sheikh, Nadeem Ahmed; Malik, Muhammad Afzaal; Arastu, Asif

2007-01-01

Damping is a major concern in the design and operation of tube bundles with loosely supported tubes in baffles for process shell and tube heat exchangers and steam generators which are used in nuclear, process and power generation industries. System damping has a strong influence on the amplitude of vibration. Damping depends upon the mechanical properties of the tube material, geometry of intermediate supports and the physical properties of shell-side fluid. Type of tube motion, number of supports, tube frequency, vibration amplitude, tube mass or diameter, side loads, support thickness, higher modes, shell-side temperature etc., affect damping in tube bundles. The importance of damping is further highlighted due to current trend of larger exchangers with increased shell-side velocities in modern units. Various damping mechanisms have been identified (Friction damping, Viscous damping, Squeeze film damping, Support damping. Two-Phase damping, and very recent-Thermal damping), which affect the performance of process exchangers and steam generators with respect to flow induced vibration design, including standard design guidelines. Damping in two-phase flow is very complex and highly void fraction, and flow-regime dependent. The current paper focuses on the various known damping mechanisms subjected to both single and two-phase cross-flow in process heat exchangers and steam generators and formulates the design guidelines for safer design. (author)

Inorganic anion exchangers for the treatment of radioactive wastes

International Nuclear Information System (INIS)

Dyer, A.; Jamil, M.A.

1987-07-01

Inorganic anion exchangers are evaluated for Tc, I and S isotope removal from aqueous nuclear waste streams. Chemical, thermal, and radiation stabilities were examined. Selected exchangers were examined in detail for their selectivities, kinetics and mechanism of the sorption process (especially in NO 3 - , OH - and BO 3 - environments). Cement encapsulation and leaching experiments were made on the exchangers showing most promise for 'radwaste' treatment. (author)

Pion double charge exchange in the Δ33 resonance region

International Nuclear Information System (INIS)

Wirzba, A.; Toki, H.; Siciliano, E.R.; Johnson, M.B.; Gilman, R.

1989-01-01

We examine the model dependence and nuclear-structure sensitivity of several Δ 33 -dominated processes contributing to pion double charge exchange on nuclei in the region of the Δ 33 resonance. These processes include the Δ 33 -nucleon interaction V NΔ and sequential scattering, in which the pion undergoes single charge exchange on two different nucleons. In all cases, the scattering takes place through the exchange of an intermediate π and ρ meson. Sequential-mediated double charge exchange is found to be only moderately sensitive to short-range correlations, meson-nucleon form factors, and the rho meson, whereas V NΔ -mediated double charge exchange is very sensitive to all these effects. Results are given for double charge exchange on 18 O (double isobaric analog transitions) and 16 O (nonanalog transitions). Sequential double charge exchange is shown to favor non-spin-flip matrix elements of the transition operator whereas V NΔ -mediated double charge exchange favors spin-flip matrix elements. The energy dependence of the zero-degree cross sections for V NΔ and sequential scattering are also different: Sequential tends to increase monotonically from 100 to 300 MeV, whereas V NΔ peaks at about 150 MeV. The delta-nucleon interaction is found likely to dominate over sequential scattering in nonanalog double charge exchange. The V NΔ is also large in analog double charge exchange, but it does not enable us to explain the anomalous behavior of the 18 O differential cross sections

Divided-evolution-based pulse scheme for quantifying exchange processes in proteins: powerful complement to relaxation dispersion experiments.

Science.gov (United States)

Bouvignies, Guillaume; Hansen, D Flemming; Vallurupalli, Pramodh; Kay, Lewis E

2011-02-16

A method for quantifying millisecond time scale exchange in proteins is presented based on scaling the rate of chemical exchange using a 2D (15)N, (1)H(N) experiment in which (15)N dwell times are separated by short spin-echo pulse trains. Unlike the popular Carr-Purcell-Meiboom-Gill (CPMG) experiment where the effects of a radio frequency field on measured transverse relaxation rates are quantified, the new approach measures peak positions in spectra that shift as the effective exchange time regime is varied. The utility of the method is established through an analysis of data recorded on an exchanging protein-ligand system for which the exchange parameters have been accurately determined using alternative approaches. Computations establish that a combined analysis of CPMG and peak shift profiles extends the time scale that can be studied to include exchanging systems with highly skewed populations and exchange rates as slow as 20 s(-1).

Chromatographic separation process with pellicular ion exchange resins that can be used for ion or isotope separation and resins used in this process

International Nuclear Information System (INIS)

Carles, M.; Neige, R.; Niemann, C.; Michel, A.; Bert, M.; Bodrero, S.; Guyot, A.

1989-01-01

For separation of uranium, boron or nitrogen isotopes, an isotopic exchange is carried out betwen an isotope fixed on an ion exchange resin and another isotope of the same element in the liquid phase contacting the resin. Pellicular resins are used comprising composite particulates with an inert polymeric core and a surface layer with ion exchange groups [fr

Anion Effects on the Ion Exchange Process and the Deformation Property of Ionic Polymer Metal Composite Actuators

Directory of Open Access Journals (Sweden)

Wataru Aoyagi

2016-06-01

Full Text Available An ionic polymer-metal composite (IPMC actuator composed of a thin perfluorinated ionomer membrane with electrodes plated on both surfaces undergoes a large bending motion when a low electric field is applied across its thickness. Such actuators are soft, lightweight, and able to operate in solutions and thus show promise with regard to a wide range of applications, including MEMS sensors, artificial muscles, biomimetic systems, and medical devices. However, the variations induced by changing the type of anion on the device deformation properties are not well understood; therefore, the present study investigated the effects of different anions on the ion exchange process and the deformation behavior of IPMC actuators with palladium electrodes. Ion exchange was carried out in solutions incorporating various anions and the actuator tip displacement in deionized water was subsequently measured while applying a step voltage. In the step voltage response measurements, larger anions such as nitrate or sulfate led to a more pronounced tip displacement compared to that obtained with smaller anions such as hydroxide or chloride. In AC impedance measurements, larger anions generated greater ion conductivity and a larger double-layer capacitance at the cathode. Based on these mechanical and electrochemical measurements, it is concluded that the presence of larger anions in the ion exchange solution induces a greater degree of double-layer capacitance at the cathode and results in enhanced tip deformation of the IPMC actuators.

Probing color-singlet exchange at D0

International Nuclear Information System (INIS)

Abbott, B.; Abolins, M.; Acharya, B.S.

1997-07-01

We present latest preliminary results on hard color-singlet exchange in proton-antiproton collisions. The fraction of dijet events produced via color-singlet exchange is measured as a function of jet transverse energy, dijet pseudorapidity separation, and proton-antiproton center-of-mass energy. These results are qualitatively consistent with a color-singlet fraction that increases with increasing quark-initiated processes

Critical overview on water - hydrogen isotopic exchange; a case study

International Nuclear Information System (INIS)

Peculea, Marius

2002-01-01

Water - hydrogen isotopic exchange process is attractive due to its high separation factor; it is neither corrosive or pollutant and, when used as a technological process of heavy water production, it requires water as raw material. Its efficiency depends strongly on the catalyst performance and geometry of the isotopic water - hydrogen exchange zone in which the isotopic transfer proceeds in two steps: liquid vapor distillation in the presence of an inert gas and a catalytic reaction in vapor - gas gaseous phase. An overview of the water hydrogen isotopic exchange is presented and technological details of the Trail - Canada facility as well as characteristics of the two pilots operated in Romania with Ni, Cr and hydrophobic catalysts are described. The mathematical approach of the successive water-water vapor-hydrogen isotopic exchange process given is based on a mathematical model worked out earlier by Palibroda. Discrepancies between computation and experimental results, lower than 11% for extreme cases and around 6% for the average range are explained as due to the ratio of the exchange potentials. Assumption is made in the theoretical approach that this ratio is positive and constant all long the column while the measurements showed that it varies within 0.7 and 1.1 at the upper end and within - 2.5 and - 4.4 at the lower end, what indicates a strong end effect. In conclusion it is stressed that a competing technological solution is emerging based on a monothermal electrolytic process or a bithermal - bibaric process both for heavy water and tritium separation process

Timing Foreign Exchange Markets

Directory of Open Access Journals (Sweden)

Samuel W. Malone

2016-03-01

Full Text Available To improve short-horizon exchange rate forecasts, we employ foreign exchange market risk factors as fundamentals, and Bayesian treed Gaussian process (BTGP models to handle non-linear, time-varying relationships between these fundamentals and exchange rates. Forecasts from the BTGP model conditional on the carry and dollar factors dominate random walk forecasts on accuracy and economic criteria in the Meese-Rogoff setting. Superior market timing ability for large moves, more than directional accuracy, drives the BTGP’s success. We explain how, through a model averaging Monte Carlo scheme, the BTGP is able to simultaneously exploit smoothness and rough breaks in between-variable dynamics. Either feature in isolation is unable to consistently outperform benchmarks throughout the full span of time in our forecasting exercises. Trading strategies based on ex ante BTGP forecasts deliver the highest out-of-sample risk-adjusted returns for the median currency, as well as for both predictable, traded risk factors.

New sorbents and ion exchangers for nuclear waste solution remediation

International Nuclear Information System (INIS)

Clearfield, A.; Peng, G.Z.; Cahill, R.A.; Bellinghausen, P.; Aly, H.I.; Scott, K.; Wang, J.D.

1993-01-01

There is now a concerted effort underway to clean up the accumulated nuclear wastes as the major sites around the country. Because of the complexity of the mixtures in the holding tanks highly specific exchangers are required to fulfill a multitude of desired tasks. These include removal of Cs + , Sr 2+ , Tc, Actinides and possible recovery of rare and precious metals. No one exchanger or sequestrant can accomplish these tasks and a variety of exchangers in a multistep process will be required. The behavior of a number of inorganic ion exchangers in a multistep process will be required. The behavior of a number of inorganic ion exchangers and new organo-inorganic exchangers towards Cs + , Sr 2+ and rare-earth ions in acid and basic media will be described. Preliminary data on the effect of high levels of sodium nitrate on the uptake of these ions will also be presented, as well as the changes observed in selectivity in simulated waste solutions. A possible separation scheme based on these data will be described

IAEA advisory group meeting on 'Technical Aspects of Atomic and Molecular Data Processing and Exchange' (14th meeting of the A + M data centres and ALADDIN network). Summary report

International Nuclear Information System (INIS)

Stephens, A.

1998-01-01

The proceedings of the IAEA Advisory Group Meeting on ''Technical Aspects of Atomic and Molecular Data Processing and Exchange (14th Meeting of A + M Data Centres and ALADDIN Network)'', held on July 21-22, 1997 in Vienna, Austria are briefly described. The meeting conclusions and recommendations on the priorities in A + M data compilation and evaluation, and on the technical aspects of data processing and exchange are also presented. The document includes 15 reports from various Data Centres

Derivation of the tunnelling exchange time for the model of trap-assisted tunnelling

International Nuclear Information System (INIS)

Racko, J.; Ballo, P.; Benko, P.; Harmatha, L.; Grmanova, A.; Breza, J.

2014-01-01

We present derivation of the tunnelling exchange times that play the key role in the model of trap assisted tunnelling (TAT) considering the electron and hole exchange processes between the trapping centre lying in the forbidden band of the semiconductor and the conduction band, valence band or a metal. All exchange processes are quantitatively described by respective exchange times. The reciprocal values of these exchange times represent the frequency with which the exchange processes contribute to the probability of occupation of the trap by free charge carriers. The crucial problem in any model of TAT is the calculation of the occupation probability. In our approach this probability is expressed in terms of only thermal and tunnelling exchange times. The concept of tunnelling exchange times presents a dominant contribution to our model of TAT. The new approach allows to simply calculate the probability of occupation of the trapping centre by a free charge carrier and subsequently to get the thermal and tunnelling generation-recombination rates occurring in the continuity equations. This is why the TAT model based on thermal and tunnelling exchange times is suitable for simulating the electrical properties of semiconductor nanostructures in which quantum mechanical phenomena play a key role. (authors)

[Comparison of the effects of exchange forms on social solidarity].

Science.gov (United States)

Inaba, Misato; Takahashi, Nobuyuki

2012-04-01

Although social solidarity is an essential component that helps maintaining social order, what produces solidarity and how does it work have not been fully investigated. We conducted an experiment to examine whether experiencing different forms of social exchange produces different levels of solidarity. We compared four forms of social exchange: reciprocal exchange (exchange resources without negotiation), negotiated exchange (with negotiation), pure-generalized exchange (giver can choose who to give) and chain-generalized exchange (giver cannot choose who to give). Two dimensions classify these exchanges: the number of players (two vs. more than two), and involvement of negotiation. Reciprocal and negotiated exchanges occur within dyads, while pure- and chain-generalized exchanges involve three or more players. Only the negotiated exchange involves negotiation process; the other exchanges are purely unilateral giving. Participants played a one-shot social dilemma game (SDG) before and after social exchange session. The more the players cooperated in SDG, the stronger the social solidarity. Results show that the cooperation rate in SDG increased more in the reciprocal, pure- and chain-generalized exchange conditions than that in the negotiated exchange condition, suggesting that social solidarity is facilitated by experiencing social exchange which does not involve negotiation.

Method of burning ion-exchange resin contaminated with radioactivity

International Nuclear Information System (INIS)

Suzuki, Shigenori.

1986-01-01

Purpose: To process spent ion exchange resins to reduce their volume, without increasing the load on a off-gas system and in a stable state and at the same time not leaving any uncombusted portions. Method: The water slurries of the ion exchange resins contaminated with radioactive materials is dehydrated or dry combusted to reduce the water content. A binder is then added to solidify the ion exchange resin. The solidified ion exchange resins are then combusted in a furnace. This prevents the ion exchange resin from being dispersed by air and combustion gases. Furthermore, the solidified ion exchange resins in the form of small pellets burn from the surface inwards. Moreover the binder is carbonized by the combustion heat and promotes combustion to convert the ion exchange resins into a solid mass, making sure that no uncombusted portion is left. (Takahashi, M.)

Ion exchange removal of chromium (iii) from tannery wastes by using a strong acid cation exchange resin amberlite ir-120 h+ and its hybrids

International Nuclear Information System (INIS)

Ahmad, T.

2014-01-01

A strong acid cation exchange resin Amberlite IR-120 H+ and its hybrids with Mn(OH)/sub 2/, Cu(OH)/sub 2/ and Fe(OH)/sub 3/ are used for the removal of chromium (III) from spent tannery bath. The experimental data give good fits with the Langmuir sorption model. The thermodynamic parameters entropy (delta S), enthalpy (delta H) and free energy (delta G) changes are computed, which reveal that the chromium removal from tannery wastes by ion exchangers is an endothermic, physical sorption and entropically driven process. The rate of sorption is found to increase with the increase of resin dosage, stirring speed and temperature. Different kinetic models such as film diffusion, particle diffusion and Lagergren pseudo first order are used to evaluate the mechanism of the process. It is found that the hybrid ion exchange resins have better removal capacity as compared to the parent ion exchanger. The increase in the removal capacity is found to be in the order of the corresponding PZC values of the hybrid ion exchangers. Further, it is suggested that the higher exchange capacity is the result of Donnan effect and specific adsorption of chromium by the oxides / hydroxides present inside the matrix of the organic cation exchanger. (author)

A conditioning process for ion exchanger resins contaminated with radioactive elements

International Nuclear Information System (INIS)

Legros, R.; Wiegert, B.; Zeh, J.L.

1993-01-01

Ion exchanger resins are embedded in a pre-polymer syrup prepared from acrylic monomers having high boiling point. A curing catalyst (a peroxide) and an activation agent (a tertiary amine) are added. 12 examples are given. 9 p

Short-term acclimation to warmer temperatures accelerates leaf carbon exchange processes across plant types.

Science.gov (United States)

Smith, Nicholas G; Dukes, Jeffrey S

2017-11-01

While temperature responses of photosynthesis and plant respiration are known to acclimate over time in many species, few studies have been designed to directly compare process-level differences in acclimation capacity among plant types. We assessed short-term (7 day) temperature acclimation of the maximum rate of Rubisco carboxylation (V cmax ), the maximum rate of electron transport (J max ), the maximum rate of phosphoenolpyruvate carboxylase carboxylation (V pmax ), and foliar dark respiration (R d ) in 22 plant species that varied in lifespan (annual and perennial), photosynthetic pathway (C 3 and C 4 ), and climate of origin (tropical and nontropical) grown under fertilized, well-watered conditions. In general, acclimation to warmer temperatures increased the rate of each process. The relative increase in different photosynthetic processes varied by plant type, with C 3 species tending to preferentially accelerate CO 2 -limited photosynthetic processes and respiration and C 4 species tending to preferentially accelerate light-limited photosynthetic processes under warmer conditions. R d acclimation to warmer temperatures caused a reduction in temperature sensitivity that resulted in slower rates at high leaf temperatures. R d acclimation was similar across plant types. These results suggest that temperature acclimation of the biochemical processes that underlie plant carbon exchange is common across different plant types, but that acclimation to warmer temperatures tends to have a relatively greater positive effect on the processes most limiting to carbon assimilation, which differ by plant type. The acclimation responses observed here suggest that warmer conditions should lead to increased rates of carbon assimilation when water and nutrients are not limiting. © 2017 John Wiley & Sons Ltd.

Segmented heat exchanger

Science.gov (United States)

Baldwin, Darryl Dean; Willi, Martin Leo; Fiveland, Scott Byron; Timmons, Kristine Ann

2010-12-14

A segmented heat exchanger system for transferring heat energy from an exhaust fluid to a working fluid. The heat exchanger system may include a first heat exchanger for receiving incoming working fluid and the exhaust fluid. The working fluid and exhaust fluid may travel through at least a portion of the first heat exchanger in a parallel flow configuration. In addition, the heat exchanger system may include a second heat exchanger for receiving working fluid from the first heat exchanger and exhaust fluid from a third heat exchanger. The working fluid and exhaust fluid may travel through at least a portion of the second heat exchanger in a counter flow configuration. Furthermore, the heat exchanger system may include a third heat exchanger for receiving working fluid from the second heat exchanger and exhaust fluid from the first heat exchanger. The working fluid and exhaust fluid may travel through at least a portion of the third heat exchanger in a parallel flow configuration.

High temperature alloys and ceramic heat exchanger

International Nuclear Information System (INIS)

Okamoto, Masaharu

1984-04-01

From the standpoint of energy saving, the future operating temperatures of process heat and gas turbine plants will become higher. For this purpose, ceramics is the most promissing candidate material in strength for application to high-temperature heat exchangers. This report deals with a servey of characteristics of several high-temperature metallic materials and ceramics as temperature-resistant materials; including a servey of the state-of-the-art of ceramic heat exchanger technologies developed outside of Japan, and a study of their application to the intermediate heat exchanger of VHTR (a very-high-temperature gas-cooled reactor). (author)

Processes of ammonia air–surface exchange in a fertilized Zea mays canopy

Directory of Open Access Journals (Sweden)

E. Nemitz

2013-02-01

Full Text Available Recent incorporation of coupled soil biogeochemical and bi-directional NH3 air–surface exchange algorithms into regional air quality models holds promise for further reducing uncertainty in estimates of NH3 emissions from fertilized soils. While this represents a significant advancement over previous approaches, the evaluation and improvement of such modeling systems for fertilized crops requires process-level field measurements over extended periods of time that capture the range of soil, vegetation, and atmospheric conditions that drive short-term (i.e., post-fertilization and total growing season NH3 fluxes. This study examines the processes of NH3 air–surface exchange in a fertilized corn (Zea mays canopy over the majority of a growing season to characterize soil emissions after fertilization and investigate soil–canopy interactions. Micrometeorological flux measurements above the canopy, measurements of soil, leaf apoplast and dew/guttation chemistry, and a combination of in-canopy measurements, inverse source/sink, and resistance modeling were employed. Over a period of approximately 10 weeks following fertilization, daily mean and median net canopy-scale fluxes yielded cumulative total N losses of 8.4% and 6.1%, respectively, of the 134 kg N ha−1 surface applied to the soil as urea ammonium nitrate (UAN. During the first month after fertilization, daily mean emission fluxes were positively correlated with soil temperature and soil volumetric water. Diurnally, maximum hourly average fluxes of ≈ 700 ng N m−2 s−1 occurred near mid-day, coincident with the daily maximum in friction velocity. Net emission was still observed 5 to 10 weeks after fertilization, although mid-day peak fluxes had declined to ≈ 125 ng N m−2 s−1. A key finding of the surface chemistry measurements was the observation of high pH (7.0–8.5 in leaf dew/guttation, which reduced the ability of the canopy to recapture soil emissions during wet periods

KRW/USD Exchange Rate Volatility and Efficient Risk Management

Directory of Open Access Journals (Sweden)

Sang-Yong Joo

1999-03-01

Full Text Available This thesis analyzes the relationship between the exchange rate of Korean Won and US dollar and the amount of foreign exchange, and studies the direction of the amendment of the risk control of foreign exchange. The GARCH (Generalized Auto Regressive Conditional Heteroscedasticity model which visually embodies the auto-regress of the wave of exchange rate shows that the amount of trade will enhance the fluidity of the exchange rate, that is, the various expects of the participators of the market affect the amount of trade and the fluidity, so in the process of trading, the trader who is in the dry tree of information bears more trading expenditure. It is predicted that the liberalization of foreign exchange rate and fluctuated exchange rate system will jointly bring the enhancement of the fluidity of the exchange rate and the amount of exchange trade. The change of this system will bring the rise of participators in foreign exchange market; meanwhile, it will also initiate superfluous fluidity of foreign exchange market. In order to overcome this problem, the government needs to implement the development strategy of the understructure of the foreign exchange market and the enterprises need to carry through systemic exchange rate risk control.

The American Foreign Exchange Option in Time-Dependent One-Dimensional Diffusion Model for Exchange Rate

International Nuclear Information System (INIS)

Rehman, Nasir; Shashiashvili, Malkhaz

2009-01-01

The classical Garman-Kohlhagen model for the currency exchange assumes that the domestic and foreign currency risk-free interest rates are constant and the exchange rate follows a log-normal diffusion process.In this paper we consider the general case, when exchange rate evolves according to arbitrary one-dimensional diffusion process with local volatility that is the function of time and the current exchange rate and where the domestic and foreign currency risk-free interest rates may be arbitrary continuous functions of time. First non-trivial problem we encounter in time-dependent case is the continuity in time argument of the value function of the American put option and the regularity properties of the optimal exercise boundary. We establish these properties based on systematic use of the monotonicity in volatility for the value functions of the American as well as European options with convex payoffs together with the Dynamic Programming Principle and we obtain certain type of comparison result for the value functions and corresponding exercise boundaries for the American puts with different strikes, maturities and volatilities.Starting from the latter fact that the optimal exercise boundary curve is left continuous with right-hand limits we give a mathematically rigorous and transparent derivation of the significant early exercise premium representation for the value function of the American foreign exchange put option as the sum of the European put option value function and the early exercise premium.The proof essentially relies on the particular property of the stochastic integral with respect to arbitrary continuous semimartingale over the predictable subsets of its zeros. We derive from the latter the nonlinear integral equation for the optimal exercise boundary which can be studied by numerical methods

Exchange rate rebounds after foreign exchange market interventions

Science.gov (United States)

Hoshikawa, Takeshi

2017-03-01

This study examined the rebounds in the exchange rate after foreign exchange intervention. When intervention is strongly effective, the exchange rate rebounds at next day. The effect of intervention is reduced slightly by the rebound after the intervention. The exchange rate might have been 67.12-77.47 yen to a US dollar without yen-selling/dollar-purchasing intervention of 74,691,100 million yen implemented by the Japanese government since 1991, in comparison to the actual exchange rate was 103.19 yen to the US dollar at the end of March 2014.

Separation of boron isotopes by ion exchange chromatography: studies with Duolite-162, a type-II resin

International Nuclear Information System (INIS)

Sharma, B.K.; Subramanian, R.; Balasubramanian, R.; Mathur, P.K.

1994-01-01

The selection of resin plays an important role in the process of separation of boron isotopes by ion exchange chromatography. The determination of (i) ion exchange capacity of Duolite-162 resin for hydroxyl - chloride exchange, (ii) hydroxyl - borate exchange, (iii) isotopic exchange separation factor by batch method and (iv) effect of concentration of boric acid on isotopic exchange separation factor to test the suitability of the above resin for this process are discussed in this report. (author)

Development of a membrane electrode assembly process for proton exchange membrane fuel cell (PEMFC)

International Nuclear Information System (INIS)

Baldo, Wilians Roberto

2003-01-01

In this work, a Membrane Electrode Assembly (MEA) producing process was developed, involving simple steps, aiming cost reduction and good reproducibility for Proton Exchange Membrane Fuel Cell (PEMFC) commercial applications. The electrodes were produced by spraying ink into both sides of the polymeric membrane, building the catalytic layers, followed by hot pressing of Gas Diffusion Layers (GDL), forming the MEA. This new producing method was called 'Spray and hot pressing hybrid method'. Concerning that all the parameters of spray and hot pressing methods are interdependent, a statistical procedure were used in order to study the mutual variables influences and to optimize the method. This study was earned out in two distinct steps: the first one, where seven variables were considered for the analysis and the second one, where only the variables that interfered in the process performance in the first step were considered for analysis. The results showed that the developed process was adequate, including only simple steps, reaching MEA's performance of 651 m A cm -2 at a potential of 600 mV for catalysts loading of 0,4 mg cm -2 Pt at the anode and 0,6 mg cm -2 Pt at the cathode. This result is compared to available commercial MEA's, with the same fuel cell operations conditions. (author)

The Life Science Exchange: a case study of a sectoral and sub-sectoral knowledge exchange programme.

Science.gov (United States)

Perkins, Brian Lee; Garlick, Rob; Wren, Jodie; Smart, Jon; Kennedy, Julie; Stephens, Phil; Tudor, Gwyn; Bisson, Jonathan; Ford, David V

2016-04-27

Local and national governments have implemented sector-specific policies to support economic development through innovation, entrepreneurship and knowledge exchange. Supported by the Welsh Government through the European Regional Development Fund, The Life Science Exchange® project was created with the aim to increase interaction between stakeholders, to develop more effective knowledge exchange mechanisms, and to stimulate the formation and maintenance of long-term collaborative relationships within the Welsh life sciences ecosystem. The Life Science Exchange allowed participants to interact with other stakeholder communities (clinical, academic, business, governmental), exchange perspectives and discover new opportunities. Six sub-sector focus groups comprising over 200 senior stakeholders from academia, industry, the Welsh Government and National Health Service were established. Over 18 months, each focus group provided input to inform healthcare innovation policy and knowledge mapping exercises of their respective sub-sectors. Collaborative projects identified during the focus groups and stakeholder engagement were further developed through sandpit events and bespoke support. Each sub-sector focus group produced a report outlining the significant strengths and opportunities in their respective areas of focus, made recommendations to overcome any 'system failures', and identified the stakeholder groups which needed to take action. A second outcome was a stakeholder-driven knowledge mapping exercise for each area of focus. Finally, the sandpit events and bespoke support resulted in participants generating more than £1.66 million in grant funding and inward investment. This article outlines four separate outcomes from the Life Science Exchange programme. The Life Science Exchange process has resulted in a multitude of collaborations, projects, inward investment opportunities and special interest group formations, in addition to securing over ten times its own

Specialists' meeting on heat exchanging components of gas-cooled reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-07-01

The objective of the Meeting sponsored by IAEA was to provide a forum for the exchange and discussion of technical information related to heat exchanging and heat conducting components for gas-cooled reactors. The technical part of the meeting covered eight subjects: Heat exchanging components for process heat applications, design and requirements, and research and development programs; Status of the design and construction of intermediate He/He exchangers; Design, construction and performance of steam generators; Metallic materials and design codes; Design and construction of valves and hot gas ducts; Description of component test facilities and test results; Manufacturing of heat exchanging components.

Specialists' meeting on heat exchanging components of gas-cooled reactors

International Nuclear Information System (INIS)

1984-01-01

The objective of the Meeting sponsored by IAEA was to provide a forum for the exchange and discussion of technical information related to heat exchanging and heat conducting components for gas-cooled reactors. The technical part of the meeting covered eight subjects: Heat exchanging components for process heat applications, design and requirements, and research and development programs; Status of the design and construction of intermediate He/He exchangers; Design, construction and performance of steam generators; Metallic materials and design codes; Design and construction of valves and hot gas ducts; Description of component test facilities and test results; Manufacturing of heat exchanging components

Tensor exchange amplitudes in K +- N charge exchange reactions

International Nuclear Information System (INIS)

Svec, M.

1979-01-01

Tensor (A 2 ) exchange amplitudes in K +- N charge exchange (CEX) are constructed from the K +- N CEX data supplemented by information on the vector (rho) exchange amplitudes from πN sca tering. We observed new features in the t-structure of A 2 exchange amplitudes which contradict the t-de pendence anticipated by most of the Regge models. The results also provide evidence for violation of weak exchange degeneracy

Oxo-exchange of gas-phase uranyl, neptunyl, and plutonyl with water and methanol.

Science.gov (United States)

Lucena, Ana F; Odoh, Samuel O; Zhao, Jing; Marçalo, Joaquim; Schreckenbach, Georg; Gibson, John K

2014-02-17

A challenge in actinide chemistry is activation of the strong bonds in the actinyl ions, AnO2(+) and AnO2(2+), where An = U, Np, or Pu. Actinyl activation in oxo-exchange with water in solution is well established, but the exchange mechanisms are unknown. Gas-phase actinyl oxo-exchange is a means to probe these processes in detail for simple systems, which are amenable to computational modeling. Gas-phase exchange reactions of UO2(+), NpO2(+), PuO2(+), and UO2(2+) with water and methanol were studied by experiment and density functional theory (DFT); reported for the first time are experimental results for UO2(2+) and for methanol exchange, as well as exchange rate constants. Key findings are faster exchange of UO2(2+) versus UO2(+) and faster exchange with methanol versus water; faster exchange of UO2(+) versus PuO2(+) was quantified. Computed potential energy profiles (PEPs) are in accord with the observed kinetics, validating the utility of DFT to model these exchange processes. The seemingly enigmatic result of faster exchange for uranyl, which has the strongest oxo-bonds, may reflect reduced covalency in uranyl as compared with plutonyl.

New Trends in Magnetic Exchange Bias

Science.gov (United States)

Mougin, Alexandra; Mangin, Stéphane; Bobo, Jean-Francois; Loidl, Alois

2005-05-01

-of-plane exchange bias, depending on the field cooling direction. This is of particular interest since it allows probing of the three-dimensional spin structure of the AF layer. The interface magnetic configuration is extremely important in the perpendicular geometry, as the short-range exchange coupling competes with a long-range dipolar interaction; the induced uniaxial anisotropy must overcome the demagnetization energy to establish perpendicular anisotropy films. Those new studies are of primary importance for the magnetic media industry as perpendicular recording exhibits potential for strongly increased storage densities. 3. Parameters tuning exchange bias in polycrystalline samples and magnetic configurations: Different parameters can be used to tune the exchange bias coupling in polycrystalline samples similar to those used in devices. Particularly fascinating aspects are the questions of the appearance of exchange bias or coercivity in ferromagnet/antiferromagnet heterostructures, and its relation to magnetic configurations formed on either side of the interface. Several papers report on either growth choices or post preparation treatments that enable tuning of the exchange bias in bilayers. The additional complexity and novel features of the exchange coupled interface make the problem particularly rich. 4. Dynamics and magnetization reversal: Linear response experiments, such as ferromagnetic resonance, have been used with great success to identify interface, surface anisotropies and interlayer exchange in multilayer systems. The exchange bias structure is particularly well suited to study because interface driven changes in the spin wave frequencies in the ferromagnet can be readily related to interlayer exchange and anisotropy parameters associated with the antiferromagnet. Because the exchange bias is intimately connected with details of the magnetization process during reversal and the subsequent formation of hysteresis, considerations of time dependence and

Improving Information Exchange in the Chicken Processing Sector Using Standardised Data Lists

Science.gov (United States)

Donnelly, Kathryn Anne-Marie; van der Roest, Joop; Höskuldsson, Stefán Torfi; Olsen, Petter; Karlsen, Kine Mari

Research has shown that to improve electronic communication between companies, universal standardised data lists are necessary. In food supply chains in particular there is an increased need to exchange data in the wake of food safety incidents. Food supply chain companies already record numerous measurements, properties and parameters. These records are necessary for legal reasons, labelling, traceability, profiling desirable characteristics, showing compliance and for meeting customer requirements. Universal standards for name and content of each of these data elements would improve information exchange between buyers, sellers, authorities, consumers and other interested parties. A case study, carried out for the chicken sector, attempted to identify the most relevant parameters including which of these were already communicated to external bodies.

CONTINUOUS MODELING OF FOREIGN EXCHANGE RATE OF USD VERSUS TRY

Directory of Open Access Journals (Sweden)

Yakup Arı

2011-01-01

Full Text Available This study aims to construct continuous-time autoregressive (CAR model and continuous-time GARCH (COGARCH model from discrete time data of foreign exchange rate of United States Dollar (USD versus Turkish Lira (TRY. These processes are solutions to stochastic differential equation Lévy-driven processes. We have shown that CAR(1 and COGARCH(1,1 processes are proper models to represent foreign exchange rate of USD and TRY for different periods of time February 2002- June 2010.

Enrichment of 15N by ion exchange chromatography

International Nuclear Information System (INIS)

Ohwaki, Masao; Ohtsuka, Haruhisa; Nomura, Masao; Okamoto, Makoto; Fujii, Yasuhiko

1996-01-01

15 N isotope separation was studied using cation exchange resins which consist of functional groups: sulfonic acid, carboxylic acid and phenol at various concentration of the eluent LiOH. The isotope separation coefficients for these ion exchange resins were observed to be nearly equal, in spite of the large difference in ion exchange characteristics. The effect of flow rate on 15 N isotope separation was also studied, and the results indicate that the operation at high flow rate would be preferable for the industrial process of 15 N enrichment. Based on the preliminary investigations, a continuous operation using a series of ion exchange columns has been carried out in order to achieve high enrichment of 15 N. (author)

Leveraging health information exchange to improve population health reporting processes: lessons in using a collaborative-participatory design process.

Science.gov (United States)

Revere, Debra; Dixon, Brian E; Hills, Rebecca; Williams, Jennifer L; Grannis, Shaun J

2014-01-01

Surveillance, or the systematic monitoring of disease within a population, is a cornerstone function of public health. Despite significant investment in information technologies (IT) to improve the public's health, health care providers continue to rely on manual, spontaneous reporting processes that can result in incomplete and delayed surveillance activities. Participatory design principles advocate including real users and stakeholders when designing an information system to ensure high ecological validity of the product, incorporate relevance and context into the design, reduce misconceptions designers can make due to insufficient domain expertise, and ultimately reduce barriers to adoption of the system. This paper focuses on the collaborative and informal participatory design process used to develop enhanced, IT-enabled reporting processes that leverage available electronic health records in a health information exchange to prepopulate notifiable-conditions report forms used by public health authorities. Over nine months, public health stakeholders, technical staff, and informatics researchers were engaged in a multiphase participatory design process that included public health stakeholder focus groups, investigator-engineering team meetings, public health survey and census regarding high-priority data elements, and codesign of exploratory prototypes and final form mock-ups. A number of state-mandated report fields that are not highly used or desirable for disease investigation were eliminated, which allowed engineers to repurpose form space for desired and high-priority data elements and improve the usability of the forms. Our participatory design process ensured that IT development was driven by end user expertise and needs, resulting in significant improvements to the layout and functionality of the reporting forms. In addition to informing report form development, engaging with public health end users and stakeholders through the participatory design

Characterization of the exchange of PBDEs in a subtropical paddy field of China: A significant inputs of PBDEs via air–foliage exchange

International Nuclear Information System (INIS)

Wang, Yan; Wang, Shaorui; Xu, Yue; Luo, Chunling; Li, Jun; Zhang, Gan

2015-01-01

Rice and the distinctive cultivation practices employed in rice growth can significantly influence the environmental fate of polybrominated diphenyl ethers (PBDEs) in a paddy field. We studied variations in PBDE concentrations in multiple compartments of a paddy field in the suburban area of Guangzhou, South China, including air, soil, water, and rice tissues. The input/output fluxes of air–surface and air–foliage exchange, atmospheric deposition and water input during different rice growth stages were measured simultaneously. Air–foliage and air–water diffusion exchanges were the key processes controlling inputs and outputs of PBDEs in paddy fields, respectively, whereas atmospheric deposition dominated inputs of higher brominated PBDEs. The high input of PBDEs via air–foliage exchange suggested that vegetation can significantly increase the air-to-field transport of PBDEs in ecosystems. The annual input of PBDEs in all paddy fields in Guangdong Province was estimated to be 22.1 kg. - Highlights: • PBDE concentrations in multiple compartments of a suburban paddy field were measured. • Air–water exchange was the key process controlling PBDE output in paddy fields. • Air–foliage exchange dominated the inputs of PBDEs in paddy fields. • Annual PBDE input in paddy fields in Guangdong Province was calculated to be 22 kg. - Air–foliage exchange is the most dominant inputs of PBDEs in the subtropical paddy fields

Guided Autobiography's Developmental Exchange: What's in It for Me?

Science.gov (United States)

Thornton, James E.; Collins, John B.; Birren, James E.; Svensson, Cheryl

2011-01-01

The developmental exchange is a central feature of social development, interpersonal dynamics, situated learning, and personal transformation. It is the enabling process in Guided Autobiography (GAB) settings that promotes the achievement of personal goals and group accomplishments. Nevertheless, these exchanges are embedded in the GAB structures…

Exchange functional by a range-separated exchange hole

International Nuclear Information System (INIS)

Toyoda, Masayuki; Ozaki, Taisuke

2011-01-01

An approximation to the exchange-hole density is proposed for the evaluation of the exact exchange energy in electronic structure calculations within the density-functional theory and the Kohn-Sham scheme. Based on the localized nature of density matrix, the exchange hole is divided into the short-range (SR) and long-range (LR) parts by using an adequate filter function, where the LR part is deduced by matching of moments with the exactly calculated SR counterpart, ensuring the correct asymptotic -1/r behavior of the exchange potential. With this division, the time-consuming integration is truncated at a certain interaction range, largely reducing the computation cost. The total energies, exchange energies, exchange potentials, and eigenvalues of the highest-occupied orbitals are calculated for the noble-gas atoms. The close agreement of the results with the exact values suggests the validity of the approximation.

Operating revenue changes in a demutualized stock exchange

Directory of Open Access Journals (Sweden)

Mohamed Hesham Abdel-Hafez

2015-03-01

Full Text Available Stock exchanges were traditionally run as cooperative venues. The globalization, the development of technology, and the increase of competition among stock exchanges forced these venues to change their structure and adopt a new one-demutualization- that can be a lifeline in facing these environmental changes in regards to stock exchanges. This new trend enables the exchange to expand their activities and supply the market with new products and services, therefore enhancing the value of the exchange itself. The main sources of revenue for traditional exchanges have been listing fees, transaction fees, membership fees and the sale of information services such as market data, quotations, and trade data. Due to the environmental changes the stock exchanges' services are now executed electronically, and in turn, this has led to an increase in the competition among exchanges. Furthermore, this increased competition has led to the re-adjustment of the regulation structure which gradually erodes the sources of revenues provided by the conventional stock exchanges. The paper divided the research plan into two sections: the first section is to highlight the concept of demutualization process; the phases of demutualization, the factors that push the stock exchanges to demutualize and the benefits of demutualization. The second section was based on statistical comparative analysis of the stock exchanges' revenues prior and after demutualization. The researcher used the regression analysis tool on seven demutualized stock exchanges during the period from 1997-2012. The paper aims to prove that demutualization has a positive effect on the revenues of the stock exchange, thus it enhances the value of the exchange.

Experimental study on CO2 frosting and clogging in a brazed plate heat exchanger for natural gas liquefaction process

Science.gov (United States)

Wu, Jitan; He, Tianbiao; Ju, Yonglin

2018-04-01

The plate-fin heat exchanger (PFHE), which has been widely used in natural gas liquefaction (LNG) industry at present, has some disadvantages such as being sensitive to the impurities in the feed gas, such as water, CO2 and H2S. Compared with the PFHE, the brazed plate heat exchanger (BPHE), which has been applied in some boil off gas (BOG) recycling LNG plants of small to middle size, has simpler inherent structure and higher impurity tolerance. In this study the BPHE is suggested to replace the PFHE to simplify or even omit the massive CO2 purification equipment for the LNG process. A set of experimental apparatus is designed and constructed to investigate the influence of the CO2 concentration of the natural gas on solid precipitation inside a typical BPHE meanly by considering the flow resistance throughout the LNG process. The results show that the maximum allowable CO2 concentration of the natural gas liquefied in the BPHE is two orders of magnitude higher than that in the PFHE under the same condition. In addition, the solid-liquid separation for the CO2 impurity is studied and the reasonable separating temperature is obtained. The solid CO2 should be separated below 135 K under the pressure of 3 MPa.

Process modeling of the impedance characteristics of proton exchange membrane fuel cells

International Nuclear Information System (INIS)

Rezaei Niya, Seyed Mohammad; Phillips, Ryan K.; Hoorfar, Mina

2016-01-01

Highlights: • The impedance of the PEM fuel cell is analytically calculated. • The measured impedances are presented for different operating conditions. • The high frequency arc in the measured Nyquist plot is related to the anode. • The intermediate frequency arc is related to the cathode. • The low frequency arc and high frequency resistance are related to the membrane. - Abstract: A complete process modeling of the impedance characteristics of the proton exchange membrane fuel cells is presented. The impedance of the cell is determined analytically and the resultant equivalent circuit is calculated. The model predictions are then compared against the measured impedances in different current densities, operating temperatures and anode and cathode relative humidities. It is shown that the model predicts the Nyquist plots in all different operating conditions extremely well. Next, the trends observed in the Nyquist plots reported in the literature are compared against the model predictions. The result of this comparison confirms the accuracy of the model. Using the verified model, various arcs in the Nyquist plots are separated and related to the fuel cell physical parameters.

Evaluation of electrochemical ion exchange for cesium elution

International Nuclear Information System (INIS)

Bontha, J.D.; Kurath, D.E.; Surma, J.E.; Buehler, M.F.

1996-04-01

Electrochemical elution was investigated as an alternative method to acid elution for the desorption of cesium from loaded ion exchange resins. The approach was found to have several potential advantages over existing technologies, in particular, electrochemical elution eliminates the need for addition of chemicals to elute cesium from the ion exchange resin. Also, since, in the electrochemical elution process the eluting solution is not in direct contact with the ion exchange material, very small volumes of the eluting solution can be used in a complete recycle mode in order to minimize the total volume of the cesium elute. In addition, the cesium is eluted as an alkaline solution that does not require neutralization with caustic to meet the tank farm specifications. Other advantages include easy incorporation of the electrochemical elution process into the present cesium recovery schemes

Preparation of inorganic ion exchangers with high selectivity for lithium isotopes

International Nuclear Information System (INIS)

Oi, Takao

2004-01-01

Development of ion exchangers that show large lithium isotope effects is hoped for to establish highly efficient chromatographic processes of lithium isotope separation. In this paper, preparation, characterization, ion exchange properties, and lithium isotope selectivity of inorganic materials that have been and still are being studied by my research group at Sophia University are reviewed. They include manganese oxides-based ion exchangers, antimonic acids and titanium/zirconium phosphates-based ion exchangers. As a result, the lithium isotope separation effects that were one order of magnitude larger than those of organic ion exchangers were obtained. Some inorganic ion exchangers were found to show ion exchange rates more than comparable to those of organic ones. (author)

A Multicontrolled Enamine Configurational Switch Undergoing Dynamic Constitutional Exchange.

Science.gov (United States)

Ren, Yansong; Svensson, Per H; Ramström, Olof

2018-05-22

A multiresponsive enamine-based molecular switch is presented, in which forward/backward configurational rotation around the C=C bond could be precisely controlled by the addition of an acid/base or metal ions. Fluorescence turn-on/off effects and large Stokes shifts were observed while regulating the switching process with Cu II . The enamine functionality furthermore enabled double dynamic regimes, in which configurational switching could operate in conjunction with constitutional enamine exchange of the rotor part. This behavior was used to construct a prototypical dynamic covalent switch system through enamine exchange with primary amines. The dynamic exchange process could be readily turned on/off by regulating the switch status with pH. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Study of isotopic exchange reactions of azidothymidine with tritium

International Nuclear Information System (INIS)

Sidorov, G.V.; Zverkov, Yu.B.; Myasoedov, N.F.

2003-01-01

Different reactions of isotopic exchange of azidothymidine (3 - azido-3 - desoxythymidine) with tritium, such as solid- and liquid-phase catalytic isotopic exchange with gaseous tritium and isotopic exchange in solution with tritium water, are investigated. It is determined that catalytic reactions of azidothymidine with gaseous tritium in solution lead to practically full reduction of azido group up to amino group. In reactions of solid-phase catalytic hydrogenation this process takes place too and 3 - azido-3 - desoxythymidine yield is from 20 to 70 %. Molar radioactivity of labelled with tritium azidothymidine prepared in reactions of solid-phase catalytic isotopic exchange with gaseous tritium and so by isotopic exchange in solution with tritium water does not exceed 0.5 Cu/mmol [ru

Isotope exchange reaction in Li2ZrO3 packed bed

International Nuclear Information System (INIS)

Kawamura, Y.; Enoeda, M.; Okuno, K.

1998-01-01

To understand the release behavior of bred tritium in a solid breeder blanket, the tritium transfer rate and tritium inventory for various mass transfer processes should be investigated. The contribution of the surface reactions (adsorption, desorption and two kinds of isotope exchange reactions) to the release process cannot be ignored. It is believed that two kinds of isotope exchange reactions (gaseous hydrogen-tritiated water and water vapor-tritiated water) occur on the surface of the solid breeder materials when hydrogen is added to the sweep gas to enhance the tritium release rate. The isotope exchange reaction study in H-D systems was carried out using a Li 2 ZrO 3 packed bed. The exchange reaction between gaseous hydrogen and water was the rate controlling step among the two kinds of exchange reactions. The reaction rate constants were quantified, and experimental equations were proposed. The equilibrium constant of the isotope exchange reaction in the H-D system was obtained from experimental data and was found to be 1.17. (orig.)

Simulations of thermal-hydraulic processes in heat exchangers- station of the cogeneration power plant

Energy Technology Data Exchange (ETDEWEB)

Studovic, M.; Stevanovic, V.; Ilic, M.; Nedeljkovic, S. [Faculty of Mechanical Engineering of Belgrade (Croatia)

1995-12-31

Design of the long district heating system to Belgrade (base load 580 MJ/s) from Thermal Power Station `Nikola Tesla A`, 30 km southwest from the present gas/oil burning boilers in New Belgrade, is being conducted. The mathematical model and computer code named TRP are developed for the prediction of the design basis parameters of heat exchangers station, as well as for selection of protection devices and formulation of operating procedures. Numerical simulations of heat exchangers station are performed for various transient conditions: up-set and abnormal. Physical model of multi-pass, shell and tube heat exchanger in the station represented is by unique steam volume, and with space discretised nodes both for water volume and tube walls. Heat transfer regimes on steam and water side, as well as hydraulic calculation were performed in accordance with TEMA standards for transient conditions on both sides, and for each node on water side. Mathematical model is based on balance equations: mass and energy for lumped parameters on steam side, and energy balances for tube walls and water in each node. Water mass balance is taken as boundary/initial condition or as specified control function. The physical model is proposed for (s) heat exchangers in the station and (n) water and wall volumes. Therefore, the mathematical model consists of 2ns+2, non-linear differential equations, including equations of state for water, steam and tube material, and constitutive equations for heat transfer on steam and water side, solved by the Runge-Kutt method. Five scenarios of heat exchangers station behavior have been simulated with the TRP code and obtained results are presented. (author)

Design and simulation of heat exchangers using Aspen HYSYS, and Aspen exchanger design and rating for paddy drying application

Science.gov (United States)

Janaun, J.; Kamin, N. H.; Wong, K. H.; Tham, H. J.; Kong, V. V.; Farajpourlar, M.

2016-06-01

Air heating unit is one of the most important parts in paddy drying to ensure the efficiency of a drying process. In addition, an optimized air heating unit does not only promise a good paddy quality, but also save more for the operating cost. This study determined the suitable and best specifications heating unit to heat air for paddy drying in the LAMB dryer. In this study, Aspen HYSYS v7.3 was used to obtain the minimum flow rate of hot water needed. The resulting data obtained from Aspen HYSYS v7.3 were used in Aspen Exchanger Design and Rating (EDR) to generate heat exchanger design and costs. The designs include shell and tubes and plate heat exchanger. The heat exchanger was designed in order to produce various drying temperatures of 40, 50, 60 and 70°C of air with different flow rate, 300, 2500 and 5000 LPM. The optimum condition for the heat exchanger were found to be plate heat exchanger with 0.6 mm plate thickness, 198.75 mm plate width, 554.8 mm plate length and 11 numbers of plates operating at 5000 LPM air flow rate.

Automated exchange transfusion and exchange rate.

Science.gov (United States)

Funato, M; Shimada, S; Tamai, H; Taki, H; Yoshioka, Y

1989-10-01

An automated blood exchange transfusion (BET) with a two-site technique has been devised by Goldmann et al and by us, using an infusion pump. With this method, we successfully performed exchange transfusions 189 times in the past four years on 110 infants with birth weights ranging from 530 g to 4,000 g. The exchange rate by the automated method was compared with the rate by Diamond's method. Serum bilirubin (SB) levels before and after BET and the maximal SB rebound within 24 hours after BET were: 21.6 +/- 2.4, 11.5 +/- 2.2, and 15.0 +/- 1.5 mg/dl in the automated method, and 22.0 +/- 2.9, 11.2 +/- 2.5, and 17.7 +/- 3.2 mg/dl in Diamond's method, respectively. The result showed that the maximal rebound of the SB level within 24 hours after BET was significantly lower in the automated method than in Diamond's method (p less than 0.01), though SB levels before and after BET were not significantly different between the two methods. The exchange rate was also measured by means of staining the fetal red cells (F cells) both in the automated method and in Diamond's method, and comparing them. The exchange rate of F cells in Diamond's method went down along the theoretical exchange curve proposed by Diamond, while the rate in the automated method was significantly better than in Diamond's, especially in the early stage of BET (p less than 0.01). We believe that the use of this automated method may give better results than Diamond's method in the rate of exchange, because this method is performed with a two-site technique using a peripheral artery and vein.

Optimization of SHINE Process: Design and Verification of Plant-Scale AG 1 Anion-Exchange Concentration Column and Titania Sorbent Pretreatment

Energy Technology Data Exchange (ETDEWEB)

Stepinski, Dominique C. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Abdul, Momen [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Youker, Amanda J. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Rotsch, David A. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Tkac, Peter [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Chemerisov, Sergey [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Vandegrift, George F. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

2016-06-01

Argonne National Laboratory has developed a Mo-recovery and -purification system for the SHINE medical technologies process, which uses a uranyl sulfate solution for the accelerator-driven production of Mo-99. The objective of this effort is to reduce the processing time for the acidification of the Mo-99 product prior to loading onto a concentration column and concentration of the Mo-99 product solution. Two methods were investigated: (1) the replacement of the titania concentration column by an anion-exchange column to decrease processing time and increase the radioiodine-decontamination efficiency and (2) pretreatment of the titania sorbent to improve its effectiveness for the Mo-recovery and -concentration columns. Promising results are reported for both methods.

Lead titanate nanotubes synthesized via ion-exchange method: Characteristics and formation mechanism

International Nuclear Information System (INIS)

Song Liang; Cao Lixin; Li Jingyu; Liu Wei; Zhang Fen; Zhu Lin; Su Ge

2011-01-01

Highlights: → Lead titanate nanotubes PbTi 3 O 7 were firstly synthesized by ion-exchange method. → Sodium titanate nanotubes have ion exchangeability. → Lead titanate nanotubes show a distinct red shift on absorption edge. - Abstract: A two-step method is presented for the synthesis of one dimensional lead titanate (PbTi 3 O 7 ) nanotubes. Firstly, titanate nanotubes were prepared by an alkaline hydrothermal process with TiO 2 nanopowder as precursor, and then lead titanate nanotubes were formed through an ion-exchange reaction. We found that sodium titanate nanotubes have ion exchangeability with lead ions, while protonated titanate nanotubes have not. For the first time, we distinguished the difference between sodium titanate nanotubes and protonated titanate nanotubes in the ion-exchange process, which reveals a layer space effect of nanotubes in the ion-exchange reaction. In comparison with sodium titanate, the synthesized lead titanate nanotubes show a narrowed bandgap.

Rational design of the exchange-spring permanent magnet.

Science.gov (United States)

Jiang, J S; Bader, S D

2014-02-12

The development of the optimal exchange-spring permanent magnet balances exchange hardening, magnetization enhancement, and the feasibility of scalable fabrication. These requirements can be met with a rational design of the microstructural characteristics. The magnetization processes in several model exchange-spring structures with different geometries have been analyzed with both micromagnetic simulations and nucleation theory. The multilayer geometry and the soft-cylinders-in-hard-matrix geometry have the highest achievable figure of merit (BH)max, while the soft-spheres-in-hard-matrix geometry has the lowest upper limit for (BH)max. The cylindrical geometry permits the soft phase to be larger and does not require strict size control. Exchange-spring permanent magnets based on the cylindrical geometry may be amenable to scaled-up fabrication.

Rational design of the exchange-spring permanent magnet

International Nuclear Information System (INIS)

Jiang, J S; Bader, S D

2014-01-01

The development of the optimal exchange-spring permanent magnet balances exchange hardening, magnetization enhancement, and the feasibility of scalable fabrication. These requirements can be met with a rational design of the microstructural characteristics. The magnetization processes in several model exchange-spring structures with different geometries have been analyzed with both micromagnetic simulations and nucleation theory. The multilayer geometry and the soft-cylinders-in-hard-matrix geometry have the highest achievable figure of merit (BH) max , while the soft-spheres-in-hard-matrix geometry has the lowest upper limit for (BH) max . The cylindrical geometry permits the soft phase to be larger and does not require strict size control. Exchange-spring permanent magnets based on the cylindrical geometry may be amenable to scaled-up fabrication. (paper)

Heat exchanger

International Nuclear Information System (INIS)

Dostatni, A.W.; Dostatni, Michel.

1976-01-01

In the main patent, a description was given of a heat exchanger with an exchange surface in preformed sheet metal designed for the high pressure and temperature service particularly encountered in nuclear pressurized water reactors and which is characterised by the fact that it is composed of at least one exchanger bundle sealed in a containment, the said bundle or bundles being composed of numerous juxtaposed individual compartments whose exchange faces are built of preformed sheet metal. The present addendun certificate concerns shapes of bundles and their positioning methods in the exchanger containment enabling its compactness to be increased [fr

Integrating Fenton's process and ion exchange for olive mill wastewater treatment and iron recovery.

Science.gov (United States)

Reis, Patrícia M; Martins, Pedro J M; Martins, Rui C; Gando-Ferreira, Licínio M; Quinta-Ferreira, Rosa M

2018-02-01

A novel integrated methodology involving Fenton's process followed by ion exchange (IE) was proposed for the treatment of olive mill wastewater. Fenton's process was optimized and it was able to remove up to 81% of chemical oxygen demand when pH 3.5, reaction time 1 h, [Fe 2+ ] = 50 mg L -1 and [Fe 2+ ]/[H 2 O 2 ] = 0.002 were applied. In spite of the potential of this treatment approach, final iron removal from the liquid typically entails pH increase and iron sludge production. The integration of an IE procedure using Lewatit TP 207 resin was found to be able to overcome this important environmental shortcoming. The resin showed higher affinity toward Fe 3+ than to Fe 2+ . However, the iron removal efficiency of an effluent coming from Fenton's was independent of the type of the initial iron used in the process. The presence of organic matter had no significant effect over the resin iron removal efficiency. Even if some efficiency decrease was observed when a high initial iron load was applied, the adsorbent mass quantity can be easily adapted to reach the desired iron removal. The use of IE is an interesting industrial approach able to surpass Fenton's peroxidation drawback and will surely boost its full-scale application in the treatment of bio-refractory effluents.

Charge exchange of muons in gases

International Nuclear Information System (INIS)

Turner, R.E.; Senba, M.

1983-06-01

The effects of the charge exchange process on muon spin dynamics have been investigated using a density operator formalism with special interest placed upon the diamagnetic muon and paramagnetic muonium signals observed after thermalization. In the charge exchange region the dynamics of the spin density operator is assumed to be determined by the muonium hyperfine interaction and by electron capture and loss processes for muons. Analytical expressions are obtained for the amplitudes and phases of the diamagnetic muon and paramagnetic muonium signals as a function of the duration of the charge exchange region, tsub(c), which is inversely proportional to the number density of the moderating gas. The theoretical signals exhibit three features which have, as yet, to be experimentally observed, namely: i) that the amplitudes associated with the muonium Larmor frequency and with the hyperfine frequency are not, in general, equal, ii) that all the amplitudes are, in general, damped oscillatory functions of tsub(c) (temperature/pressure) and iii) that phase jumps occur when an amplitude decreases to zero and then increases with falling pressure. Fits to the experimental argon data are discussed in light of the above points

Process for removing a mixture containing iodine and alkyl iodine compounds from a gas phase or aqueous solution with ion-exchange resins

Energy Technology Data Exchange (ETDEWEB)

Shimizu, H; Mizuuchi, A; Yokoyama, F

1968-10-04

Iodine and alkyl iodine compounds are removed from a gas phase or aqueous solution containing salts, iodine and iodine compounds, such as the ambient gas in a reactor, if an accident should occur. The process comprises contacting the phase or solution: (a) with a hydrogen type strongly acidic cationic exchange resin, (b) with an anionic exchange resin containing quarternary ammonium and (c) with an anionic exchange resin containing free basic type tertiary amine, in this order or by reversing the order of the two anionic exchange resins. Although no problems arise in the liquid phase reaction, the ion-exchange resins in the gas phase reaction are desired in the moist state in order to stable maintain the migration speed of the materials to be removed regardless of the relative humidity of the amibent gas. In example I, Amberlite IRA-900 of 200 mm thickness as the lowermost bed, Amberlite IRA93 of 200 mm thickness as the middle bed and Amberlite 200 of 200 mm thickness as the uppermost bed were filled respectively, in a methacrylate resin cylinder with an inner diameter of 25 mm. A solution containing 15.9 mg/1 of iodine, 41.2 mg/1 of methyl iodide and 550 mg/1 of sodium carbonate flows at a rate of 15 liter/hr downward through the beds. As a result of testing, no iodine, iodine ions, iodic acid ions and methyl iodine were detected. The amount of water the beds could treat was 60 times the total quantity of the filled resins.

Interfacial spin cluster effects in exchange bias systems

Energy Technology Data Exchange (ETDEWEB)

Carpenter, R., E-mail: rc548@york.ac.uk; Vallejo-Fernandez, G.; O' Grady, K. [Department of Physics, The University of York, York YO10 5DD (United Kingdom)

2014-05-07

In this work, the effect of exchange bias on the hysteresis loop of CoFe is observed. The evolution of the coercivities and the shift of the hysteresis loop during the annealing process has been measured for films deposited on NiCr and Cu seed layers. Through comparison of the as deposited and field annealed loops, it is clear that for an exchange biased material, the two coercivities are due to different reversal processes. This behaviour is attributed to spin clusters at the ferromagnet/antiferromagnet interface, which behave in a similar manner to a fine particle system.

Ion-exchange concentration of inorganic anions from aqueous solution

Directory of Open Access Journals (Sweden)

L. P. Bondareva

2016-01-01

Full Text Available Monitoring of natural waters in the present time - consuming process, the accuracy of which is influenced by many factors: the composition of water, the presence of impurities and "interfering" components. The water sample preparation process includes the step of concentration and separation of ions determined. The most versatile, efficient, and frequently used method is the concentration of inorganic anions from aqueous solutions by ion exchanger, which can optimize the composition of water to the optimal for identification and quantitative determination of anions. The characteristics of sorption chloride, nitrate and sulfate ions of basic anion exchange resin AВ-17 and Purolite A430 were compared in the article. The constants of protolysis of ion exchangers both AB 17 and Purolite A430 are the same and equal 0.037 ± 0,002. The value of total capacity (POE Purolite A430 was 4.3 mmol/g, AB 17 – 3.4 mmol/g. The studied ion exchangers have the same type of ionic groups – quaternary ammonium, but their number and denotes differ. The number of quaternary ammonium groups is higher in Purolite A430, respectively the number of absorbed anions of these ion exchanger is higher. The values of dynamic exchange capacity (DOE of ion exchanger Purolite A430 is higher than these values of AB-17 and equal to 1.48 ± 0.03 mmol / dm3 for chloride ion, 1.50 ± 0.03 mmol / dm3 for nitrate ion, 1.62 ± 0.03 mmol / dm3 for sulfate ion. The values of the POE and DOE of anion-exchange resins Purolite A430 and AV-17 and the characteristics of the individual sorption of chloride, nitrate, sulfate ions showed an advantage of the Purolite for the concentrationing of anions. It is found that times of anions sorption from triple-anion solutions by Purolite A430 are significantly different for different anions, and these times are close for anion-exchanger AV-17. It proves the possibility of quantitative separation and concentration by anion-exchanger Purolite A430.

Recoil chemistry and solid state exchange in cobalt complexes : a new model

International Nuclear Information System (INIS)

Ramshesh, V.

1981-01-01

During the last thirty years considerable work has been done on various aspects of recoil chemistry and solid state exchange in cobalt complexes. Several interesting features such as 'oxygen effect', 'water of hydration effect', 'dilution with isomorphous materials', etc., have been observed. These data led workers to reject the older hypothesis based on 'fragmentation' and 'recombination' and suggest models based on exciton or electron induced exchange. However some recent data show that perhaps both the processes viz., thermal annealing in n-irradiated systems and solid state exchange are not bulk processes. This has led the author to propose a new model. In this model greater emphasis is placed on dissociation reactions followed by recombination and/or exchange reactions. (author)

Advanced Heat/Mass Exchanger Technology for Geothermal and Solar Renewable Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Greiner, Miles [Univ. of Nevada, Reno, NV (United States); Childress, Amy [Univ. of Nevada, Reno, NV (United States); Hiibel, Sage [Univ. of Nevada, Reno, NV (United States); Kim, Kwang [Univ. of Nevada, Reno, NV (United States); Park, Chanwoo [Univ. of Nevada, Reno, NV (United States); Wirtz, Richard [Univ. of Nevada, Reno, NV (United States)

2014-12-16

Northern Nevada has abundant geothermal and solar energy resources, and these renewable energy sources provide an ample opportunity to produce economically viable power. Heat/mass exchangers are essential components to any energy conversion system. Improvements in the heat/mass exchange process will lead to smaller, less costly (more efficient) systems. There is an emerging heat transfer technology, based on micro/nano/molecular-scale surface science that can be applied to heat/mass exchanger design. The objective is to develop and characterize unique coating materials, surface configurations and membranes capable of accommodating a 10-fold increase in heat/mass exchanger performance via phase change processes (boiling, condensation, etc.) and single phase convective heat/mass transfer.

Liquid Salt Heat Exchanger Technology for VHTR Based Applications

Energy Technology Data Exchange (ETDEWEB)

Anderson, Mark; Sridhara, Kumar; Allen, Todd; Peterson, Per

2012-10-11

The objective of this research is to evaluate performance of liquid salt fluids for use as a heat carrier for transferring high-temperature process heat from the very high-temperature reactor (VHTR) to chemical process plants. Currently, helium is being considered as the heat transfer fluid; however, the tube size requirements and the power associated with pumping helium may not be economical. Recent work on liquid salts has shown tremendous potential to transport high-temperature heat efficiently at low pressures over long distances. This project has two broad objectives: To investigate the compatibility of Incoloy 617 and coated and uncoated SiC ceramic composite with MgCl2-KCl molten salt to determine component lifetimes and aid in the design of heat exchangers and piping; and, To conduct the necessary research on the development of metallic and ceramic heat exchangers, which are needed for both the helium-to-salt side and salt-to-process side, with the goal of making these heat exchangers technologically viable. The research will consist of three separate tasks. The first task deals with material compatibility issues with liquid salt and the development of techniques for on-line measurement of corrosion products, which can be used to measure material loss in heat exchangers. Researchers will examine static corrosion of candidate materials in specific high-temperature heat transfer salt systems and develop an in situ electrochemical probe to measure metallic species concentrations dissolved in the liquid salt. The second task deals with the design of both the intermediate and process side heat exchanger systems. Researchers will optimize heat exchanger design and study issues related to corrosion, fabrication, and thermal stresses using commercial and in-house codes. The third task focuses integral testing of flowing liquid salts in a heat transfer/materials loop to determine potential issues of using the salts and to capture realistic behavior of the salts in a

Simulations of NMR pulse sequences during equilibrium and non-equilibrium chemical exchange

International Nuclear Information System (INIS)

Helgstrand, Magnus; Haerd, Torleif; Allard, Peter

2000-01-01

The McConnell equations combine the differential equations for a simple two-state chemical exchange process with the Bloch differential equations for a classical description of the behavior of nuclear spins in a magnetic field. This equation system provides a useful starting point for the analysis of slow, intermediate and fast chemical exchange studied using a variety of NMR experiments. The McConnell equations are in the mathematical form of an inhomogeneous system of first-order differential equations. Here we rewrite the McConnell equations in a homogeneous form in order to facilitate fast and simple numerical calculation of the solution to the equation system. The McConnell equations can only treat equilibrium chemical exchange. We therefore also present a homogeneous equation system that can handle both equilibrium and non-equilibrium chemical processes correctly, as long as the kinetics is of first-order. Finally, the same method of rewriting the inhomogeneous form of the McConnell equations into a homogeneous form is applied to a quantum mechanical treatment of a spin system in chemical exchange. In order to illustrate the homogeneous McConnell equations, we have simulated pulse sequences useful for measuring exchange rates in slow, intermediate and fast chemical exchange processes. A stopped-flow NMR experiment was simulated using the equations for non-equilibrium chemical exchange. The quantum mechanical treatment was tested by the simulation of a sensitivity enhanced 15 N-HSQC with pulsed field gradients during slow chemical exchange and by the simulation of the transfer efficiency of a two-dimensional heteronuclear cross-polarization based experiment as a function of both chemical shift difference and exchange rate constants

Cation exchange process for recovery of plutonium from laboratory solutions containing chloride

International Nuclear Information System (INIS)

Gray, L.W.

1978-10-01

A cation exchange technique was developed for the separation of plutonium from laboratory solutions containing either Pu(III) or Pu(III)--Pu(IV) mixtures in acidic solutions containing chloride ions. The procedure consists of adjusting the acid concentration to less than one molar and adjusting the valence of the plutonium ion to the (III) state, if necessary. The adjusted solution is fed to a cation exchange column and washed with distilled water to remove residual chlorides from the column. Plutonium is then eluted from the column with 5M nitric acid containing 0.34M sulfamic acid. This procedure was used to separate plutonium from 1.2M chloride solution on a production-scale column. Typical plutonium recovery was 99.97%, while greater than 96% of the original chloride was rejected

Metallic materials for heat exchanger components and highly stressed internal of HTR reactors for nuclear process heat generation

International Nuclear Information System (INIS)

1982-01-01

The programme was aimed at the development and improvement of materials for the high-temperature heat exchanger components of a process steam HTR. The materials must have high resistance to corrosion, i.e. carburisation and internal oxidation, and high long-term toughness over a wide range of temperatures. They must also meet the requirements set in the nuclear licensing procedure, i.e. resistance to cyclic stress and irradiation, non-destructive testing, etc. Initially, it was only intended to improve and qualify commercial alloys. Later on an alloy development programme was initiated in which new, non-commercial alloys were produced and modified for use in a nuclear process heat facility. Separate abstracts were prepared for 19 pays of this volume. (orig./IHOE) [de

Postsynthetic Doping of MnCl2 Molecules into Preformed CsPbBr3 Perovskite Nanocrystals via a Halide Exchange-Driven Cation Exchange.

Science.gov (United States)

Huang, Guangguang; Wang, Chunlei; Xu, Shuhong; Zong, Shenfei; Lu, Ju; Wang, Zhuyuan; Lu, Changgui; Cui, Yiping

2017-08-01

Unlike widely used postsynthetic halide exchange for CsPbX 3 (X is halide) perovskite nanocrystals (NCs), cation exchange of Pb is of a great challenge due to the rigid nature of the Pb cationic sublattice. Actually, cation exchange has more potential for rendering NCs with peculiar properties. Herein, a novel halide exchange-driven cation exchange (HEDCE) strategy is developed to prepare dually emitting Mn-doped CsPb(Cl/Br) 3 NCs via postsynthetic replacement of partial Pb in preformed perovskite NCs. The basic idea for HEDCE is that the partial cation exchange of Pb by Mn has a large probability to occur as a concomitant result for opening the rigid halide octahedron structure around Pb during halide exchange. Compared to traditional ionic exchange, HEDCE is featured by proceeding of halide exchange and cation exchange at the same time and lattice site. The time and space requirements make only MnCl 2 molecules (rather than mixture of Mn and Cl ions) capable of doping into perovskite NCs. This special molecular doping nature results in a series of unusual phenomenon, including long reaction time, core-shell structured mid states with triple emission bands, and dopant molecules composition-dependent doping process. As-prepared dual-emitting Mn-doped CsPb(Cl/Br) 3 NCs are available for ratiometric temperature sensing. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The international educational exchanges: history and modern value

Directory of Open Access Journals (Sweden)

L S Astafeva

2009-09-01

Full Text Available In article the history, a current state and prospects of development of the international educational exchanges is considered. Influence world processes of globalisation and internationalisation on educational processes of multinational high schools is shown.

Deposits on heat exchanging surfaces, causes in the bleaching process and countermeasures; Belaeggningar paa vaermevaexlare, orsaker i blekprocessen och aatgaerder

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik [AaF-Energi och Miljoe AB, Stockholm (Sweden); Staahl, Charlotte; Widell, Lars [AaF-Celpap AB, Stockholm (Sweden)

2003-06-01

Energy conservation in process industry implies to a large extent recovery of heat (or cold) from a process stream and its utilization for another process stream. The savings of energy that can be achieved depend on the process streams, but also on the efficiency of the heat exchange. A small driving temperature difference is a condition for an extensive recovery and a satisfactory preservation of its quality, i.e. its temperature. As process streams contain compounds or components that can precipitate and form deposits on heat exchanging surfaces, the recovery of heat is degraded. In the pulp and paper industry, two trends combine to increase the extent of fouling: a larger degree of closure for the process and a change in pH-profile caused by a switch to elementary chlorine free bleaching. In this study, the occurrence of deposits has been investigated for the mills that produce mechanical pulp and for the fiber line in mills producing chemical pulp. Deposits on the evaporator surfaces are treated in a parallel study. Except for some plants, deposits are not an important problem today. That does not mean that there has not been any problem or that problems will not occur. The origin of deposits lies in the chemistry of the process, but deposits have consequences for the thermal energy management. A list of possible actions in order to avoid deposits or to mitigate their consequences has been dressed in this report. They should be considered with the following order of priority: avoiding that the compounds that may form deposits enter at all the process, section 6.1; avoiding that these compounds form a deposit once they have entered the process, section 6.2; cleaning if nothing else helps or costs too much, section 6.3. Some of these methods are well known or are conventional changes in the processes. Some of these methods are less well proven or less well documented. In a longer time perspective, the kidney technology that is being developed could contribute to

Numerical analysis of exhaust gas flow during the gas exchange process and the design optimization; Haiki manihorudonai no hiteijo nagare kaiseki gijutsu to sono oyo

Energy Technology Data Exchange (ETDEWEB)

Yoshizawa, K; Takeyama, S; Sakai, E; Tanzawa, K [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

A simulation method was developed to estimate exhaust gas flow during the gas exchange process. In this simulation, one dimensional in-cylinder gas flow calculation and three dimensional exhaust gas flow calculation were combined. Gas flow inside the exhaust manifold catalyst during gas exchange was agreed in experiments. A simulation method was applied to select oxygen sensor location. A prediction of the oxygen sensor sensitivity of each cylinder gas was presented. The possibility of selecting oxygen sensor location in the exhaust manifold using calculation was proved. 5 refs., 10 figs., 1 tab.

Energy and Environment. Electric power stock exchange

International Nuclear Information System (INIS)

Fazioli, R.; Antonioli, B.; Beccarello, M.; Da Rin, B.

2000-01-01

In this paper are reported the structural characteristics of electric power stock exchange in the processes liberalization of european electric markets. International experience are also considered [it

HRM Implementation by Multiple HRM Actors : A Social Exchange Perspective

NARCIS (Netherlands)

Bos-Nehles, Anna Christina; Meijerink, Jeroen Gerard

2018-01-01

In this study, we understand HRM implementation as a social process that depends on the social exchange relationships between line managers and both HR professionals and employees. As such, we offer a fresh approach to understanding HRM implementation by concentrating on the social exchange among

Process of heat exchangers manufactured by Scientific and Engineering Services (S.E.S.)

International Nuclear Information System (INIS)

Khurshid, S.

1995-01-01

The objective of this report is to have a comprehensive overview of heat exchanger fouling problems as they occur in the industrial manufacturing sector. Specifically the types of fouling, conditions that influence fouling, the mitigation and accommodation techniques currently being used and mitigation technology trends are discussed. Finally a table top apparatus is designed and fabricated to develop an on line mechanical technique of rubber ball system for the removal of dirt and scales of that exchangers. Experimental results of this apparatus show that the cleaning efficiency can be raised if this mechanical technique is used together with current chemical fouling removal methods. (author)

Ion Exchange Temperature Testing with SRF Resin - 12088

Energy Technology Data Exchange (ETDEWEB)

Russell, R.L.; Rinehart, D.E.; Brown, G.N.; Peterson, R.A. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States)

2012-07-01

Ion exchange using the Spherical Resorcinol-Formaldehyde (SRF) resin has been selected by the U.S. Department of Energy's Office of River Protection for use in the Pretreatment Facility of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) and for potential application in an at-tank deployment for removing Cs-137. Recent proposed changes to the WTP ion exchange process baseline indicate that higher temperatures (50 deg. C) to alleviate post-filtration precipitation issues prior to reaching the ion exchange columns may be required. Therefore, it is important to understand the behavior of SRF resin performance under the conditions expected with the new equipment and process changes. This research examined the impact of elevated temperature on resin loading and resin degradation during extended solution flow at elevated temperature (45 deg., 50 deg., 55 deg., 60 deg., 65 deg., 75 deg. C). Testing for extended times at elevated temperatures showed that the resin does degrade and loading capacity is reduced at and above 45 deg. C. Above 60 deg. C the resin appears to not load at all. It was observed that the resin disintegrated at 75 deg. C until not much was left and partially disintegrated at 65 deg. C, which caused the column to plug in both tests after ∼336 hours. The results indicate that WTP will lose resin loading capacity if the ion exchange process is performed above 25 deg. C, and the resin will disintegrate above 65 deg. C. Therefore, WTP will have a restricted operating range of temperatures to perform the ion exchange process with this resin. PNNL and WTP are currently evaluating the operating limits of the resin in further detail. Aging in 0.5 M HNO{sub 3} also caused the resin to lose capacity above 25 deg. C and to completely dissolve at 55 deg. C. Again, WTP will have a restricted operating range of temperatures when eluting the resin with nitric acid in order to maintain resin loading capacity and avoid disintegration of the resin

A General Model for Cost Estimation in an Exchange

Directory of Open Access Journals (Sweden)

Benzion Barlev

2014-03-01

Full Text Available Current Generally Accepted Accounting Principles (GAAP state that the cost of an asset acquired for cash is the fair value (FV of the amount surrendered, and that of an asset acquired in a non-monetary exchange is the FV of the asset surrendered or, if it is more “clearly evident,” the FV of the acquired asset. The measurement method prescribed for a non-monetary exchange ignores valuable information about the “less clearly evident” asset. Thus, we suggest that the FV in any exchange be measured by the weighted average of the exchanged assets’ FV estimations, where the weights are the inverse of the variances’ estimations. This alternative valuation process accounts for the uncertainty involved in estimating the FV of each of the asset in the exchange. The proposed method suits all types of exchanges: monetary and non-monetary. In a monetary transaction, the weighted average equals the cash paid because the variance of its FV is nil.

Hydrogen/deuterium exchange of multiply-protonated cytochrome c ions

International Nuclear Information System (INIS)

Wood, T.D.; Guan, Ziqiang; O'Connor, P.B.

1995-01-01

Low resolution measurements show gaseous multiply-protonated cytochrome c ions undergo hydrogen/deuterium (H/D) exchange with pseudo first-order kinetics at three distinct exchange levels, suggesting the co-existence of gaseous protein conformations. Although exchange levels first increase with increasing charge values, they decrease at the highest charge values, consistent with solution-phase behavior of cytochrome c, where the native structure unfolds with decreasing pH until folding into a compact A-state at lowest pH. High resolution measurements indicate the presence of at least six H/D exchange levels. Infrared (IR) laser heating and fast collisions via quadrupolar excitation (QE) increase H/D exchange levels (unfolding) while charge-stripping ions to lower charge values can increase or decrease H/D exchange levels (unfolding or folding). Wolynes has suggested studying proteins in vacuo could play an important role in delineating the contributions various forces play in the protein folding process, provided appropriate comparisons can be made between gas-phase and solution-phase structures

A review of the radiation stability of ion exchange materials

International Nuclear Information System (INIS)

Pillay, K.K.S.

1986-01-01

A comprehensive literature survey on the radiation stability of synthetic organic ion exchangers was published in this journal (Vol. 97, No. 1.). This paper is a brief review of the major findings of this survey along with similar information on synthetic inorganic ion exchangers. The primary goal of this literature survey is to review present knowledge on the effects of ionizing radiations on synthetic ion exchange materials used in radiochemical processing. The information available in the literature shows some general trends in observed qualitative effects by different types of organic and inorganic ion exchange materials. (author)

Capability of cation exchange technology to remove proven N-nitrosodimethylamine precursors.

Science.gov (United States)

Li, Shixiang; Zhang, Xulan; Bei, Er; Yue, Huihui; Lin, Pengfei; Wang, Jun; Zhang, Xiaojian; Chen, Chao

2017-08-01

N-nitrosodimethylamine (NDMA) precursors consist of a positively charged dimethylamine group and a non-polar moiety, which inspired us to develop a targeted cation exchange technology to remove NDMA precursors. In this study, we tested the removal of two representative NDMA precursors, dimethylamine (DMA) and ranitidine (RNTD), by strong acidic cation exchange resin. The results showed that pH greatly affected the exchange efficiency, with high removal (DMA>78% and RNTD>94%) observed at pHMg 2+ >RNTD + >K + >DMA + >NH 4 + >Na + . The partition coefficient of DMA + to Na + was 1.41±0.26, while that of RNTD + to Na + was 12.1±1.9. The pseudo second-order equation fitted the cation exchange kinetics well. Bivalent inorganic cations such as Ca 2+ were found to have a notable effect on NA precursor removal in softening column test. Besides DMA and RNTD, cation exchange process also worked well for removing other 7 model NDMA precursors. Overall, NDMA precursor removal can be an added benefit of making use of cation exchange water softening processes. Copyright © 2017. Published by Elsevier B.V.

Reversible Size Control of Silver Nanoclusters via Ligand-exchange

KAUST Repository

Bootharaju, Megalamane Siddaramappa

2015-05-21

The properties of atomically monodisperse noble metal nanoclusters (NCs) are intricately intertwined with their precise molecular formula. The vast majority of size-specific NC syntheses start from the reduction of the metal salt and thiol ligand mixture. Only in gold was it recently shown that ligand-exchange could induce the growth of NCs from one atomically precise species to another; a process of yet unknown reversibility. Here, we present a process for the ligand-exchange-induced growth of atomically precise silver NCs, in a biphasic liquid-liquid system, which is particularly of interest because of its complete reversibility and ability to occur at room temperature. We explore this phenomenon in-depth using Ag35(SG)18 [SG= glutathionate] and Ag44(4-FTP)30 [4-FTP= 4-fluorothiophenol] as model systems. We show that the ligand-exchange conversion of Ag35(SG)18 into Ag44(4-FTP)30 is rapid (< 5 min) and direct, while the reverse process proceeds slowly through intermediate cluster sizes. We adapt a recently developed theory of reverse Ostwald ripening to model the NCs’ interconvertibility. The model’s predictions are in good agreement with the experimental observations, and they highlight the importance of small changes in the ligand-metal binding energy in determining the final equilibrium NC size. Based on the insight provided by this model, we demonstrated experimentally that by varying the choice of ligands, ligand-exchange can be used to obtain different sized NCs. The findings in this work establish ligand-exchange as a versatile tool for tuning cluster sizes.

Reversible Size Control of Silver Nanoclusters via Ligand-exchange

KAUST Repository

Bootharaju, Megalamane Siddaramappa; Burlakov, Victor M.; Besong, Tabot M.D.; Joshi, Chakra Prasad; AbdulHalim, L; Black, David; Whetten, Robert; Goriely, Alain; Bakr, Osman

2015-01-01

The properties of atomically monodisperse noble metal nanoclusters (NCs) are intricately intertwined with their precise molecular formula. The vast majority of size-specific NC syntheses start from the reduction of the metal salt and thiol ligand mixture. Only in gold was it recently shown that ligand-exchange could induce the growth of NCs from one atomically precise species to another; a process of yet unknown reversibility. Here, we present a process for the ligand-exchange-induced growth of atomically precise silver NCs, in a biphasic liquid-liquid system, which is particularly of interest because of its complete reversibility and ability to occur at room temperature. We explore this phenomenon in-depth using Ag35(SG)18 [SG= glutathionate] and Ag44(4-FTP)30 [4-FTP= 4-fluorothiophenol] as model systems. We show that the ligand-exchange conversion of Ag35(SG)18 into Ag44(4-FTP)30 is rapid (< 5 min) and direct, while the reverse process proceeds slowly through intermediate cluster sizes. We adapt a recently developed theory of reverse Ostwald ripening to model the NCs’ interconvertibility. The model’s predictions are in good agreement with the experimental observations, and they highlight the importance of small changes in the ligand-metal binding energy in determining the final equilibrium NC size. Based on the insight provided by this model, we demonstrated experimentally that by varying the choice of ligands, ligand-exchange can be used to obtain different sized NCs. The findings in this work establish ligand-exchange as a versatile tool for tuning cluster sizes.

Double Pomeron Exchange from the ISR to the SSC

International Nuclear Information System (INIS)

Albrow, M.G.

1989-01-01

After a general introduction to Double Pomeron Exchange I show how the existence of the process was demonstrated at the CERN Intersecting Storage Rings and discuss its value there as a spectroscopic tool in meson/glueball studies. At higher collision energies as now available at the Super Proton Synchrotron and Fermilab pp-bar Colliders it would be very interesting to study hard processes in Double Pomeron Exchange and investigate Pomeron structure. The still higher Large Hadron Collider and Superconducting Super Collider energies extend the range of this physics dramatically, possibly into the electroweak sector. (author)

Structure design of primary heat-exchanger for the MHWRR

International Nuclear Information System (INIS)

Li Yanshui; Cao Zhibin

1999-01-01

Primary heat-exchanger is one of the key equipment in the Multi-application Heavy Water Research Reactor (MHWRR). Its structure design ought to meet as much possible as the demands for safety, feasibility and economy. To reduce the liquid resistance, the locating structure between inner tube and outer tube is distributed spirally. The edge of outer tube is processed in the shape of hexahedron and then splice-welded into honeycomb structure thereby the heat-exchanger has the smallest outer diameter compared with that with the same heat-exchanging area according to 'Normal Design', 'Anabasis Design' is applied to the design for parts with Safety Class I, to ensure safety of the heat-exchanger

Ion exchange equilibrium constants

CERN Document Server

Marcus, Y

2013-01-01

Ion Exchange Equilibrium Constants focuses on the test-compilation of equilibrium constants for ion exchange reactions. The book first underscores the scope of the compilation, equilibrium constants, symbols used, and arrangement of the table. The manuscript then presents the table of equilibrium constants, including polystyrene sulfonate cation exchanger, polyacrylate cation exchanger, polymethacrylate cation exchanger, polysterene phosphate cation exchanger, and zirconium phosphate cation exchanger. The text highlights zirconium oxide anion exchanger, zeolite type 13Y cation exchanger, and

Automatic fuel exchanging device

International Nuclear Information System (INIS)

Takahashi, Fuminobu.

1984-01-01

Purpose: To enable to designate the identification number of a fuel assembly in a nuclear reactor pressure vessel thereby surely exchanging the designated assembly within a short time. Constitution: Identification number (or letter) pressed on a grip of a fuel assembly is to be detected by a two-dimensional ultrasonic probe of a pull-up mechanism. When the detected number corresponds with the designated number, a control signal is outputted, whereby the pull-up drive control mechanism or pull-up mechanism responds to pull-up and exchange the fuel assembly of the identified number. With such a constitution, the fuel assembly can rapidly and surely be recognized even if pressed letters deviate to the left or right of the probe, and further, the hinge portion and the signal processing portion can be simplified. (Horiuchi, T.)

Viscose liquid heat treatment using plate scraper heat exchanger

Directory of Open Access Journals (Sweden)

K. A. Rashkin

2012-01-01

Full Text Available The current work analyzes the use of different types of heat exchangers, depending on the technology of production. It is taken the detail analysis of the ways of applicability of various types of heat exchangers, depending on the viscosity of the processed product. It is posed the problem of the analytical determination of the required area of heat exchange with the use of differential equations of heat transfer in a moving liquid media, written in cylindrical coordinates, for symmetrical temperature distribution, without taking in account the energy dissipation.

Properties of sulfonated cation-exchangers made from petroleum asphaltites

International Nuclear Information System (INIS)

Pokonova, Yu.V.; Pol'kin, G.B.; Proskuryakov, V.A.

1982-01-01

The use of ion-exchangers in radiochemical technology is accompanied by changes of their properties under the influence of ionizing radiation. The rate of development of these processes depends on the nature and structure of the matrix and on the nature and amount of ionic groups. We have proposed a method of synthesis of ion-exchangers resistant to γ radiation from petroleum asphaltites. Continuing these investigations, we prepared cation-exchangers by sulfonation of a mixture of petroleum asphaltites and acid asphalt. An investigation of their radiation resistance is described in this paper

Optimal model of radiocarbon residence time in exchange reservoir

International Nuclear Information System (INIS)

Dergachev, V.A.

1977-01-01

Radiocarbon content variations in the earth atmosphere were studied using a mathematical model. The so-called exchange reservoir was considered consisting of layers, and the radiocarbon exchange rate at the interfaces between these layers was supposed to be constant. The process of 14 C mixing and exchange in a dynamic system is described by a system of nonhomogeneous 1st order differential equations. The model also accounts for the change in rate of radiocarbon formation in the earth atmosphere due to cosmic and geophysical effects (solar activity, solar cycle, etc.). (J.P.)

Processes of Ammonia Air-Surface Exchange in a Fertilized Zea Mays Canopy

Science.gov (United States)

Recent incorporation of coupled soil biogeochemical and bi-directional NH3 air-surface exchange algorithms into regional air quality models holds promise for further reducing uncertainty in estimates of NH3 emissions from fertilized soils. While this advancement represents a sig...

Molecular exchange of n-hexane in zeolite sieves studied by diffusion-diffusion and T{sub 1}-diffusion nuclear magnetic resonance exchange spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Neudert, Oliver; Stapf, Siegfried; Mattea, Carlos, E-mail: carlos.mattea@tu-ilmenau.de [Fachgebiet Technische Physik II/Polymerphysik, Institute of Physics, Technische Universitaet Ilmenau, PO Box 100 565, 98684 Ilmenau (Germany)

2011-03-15

Molecular exchange properties and diffusion of n-hexane embedded in a bimodal pore structure with characteristic length scales in the order of nano and micrometres, respectively, formed by packing of zeolite particles, are studied. Two-dimensional (2D) nuclear magnetic resonance (NMR) diffusion correlation experiments together with relaxation-diffusion correlation experiments are performed at low magnetic field using a single-sided NMR scanner. The exchange time covers a range from 10{sup -3} to 10{sup -1} s. The molecular exchange properties are modulated by transport inside the zeolite particles. Different exchange regimes are observed for molecules starting from different positions inside the porous sample. The influence of the spin-lattice relaxation properties of the fluid molecules inside the zeolite particles on the signal intensity is also studied. A Monte Carlo simulation of the exchange process is performed and is used to support the analysis of the experimental data.

Triple-membrane reduces need for ion exchange regeneration

International Nuclear Information System (INIS)

Valcour, H.

1989-01-01

Triple-membrane water treatment systems are comprised of ultrafiltration units for pretreatment, electrodialysis reversal primary demineralizers, reverse osmosis secondary demineralizers, portable ion exchange unit polishing demineralizers, and ultraviolet sterilizers. The triple-membrane process is designed to provide an unprecedented degree of pretreatment to maximize efficiency, durability and reliability of the reverse osmosis, whilst reducing the required regeneration frequency of the ion exchange demineralizer by one to two orders of magnitude. (author)

High-Temperature Structural Analysis Model of the Process Heat Exchanger for Helium Gas Loop (II)

International Nuclear Information System (INIS)

Song, Kee Nam; Lee, Heong Yeon; Kim, Chan Soo; Hong, Seong Duk; Park, Hong Yoon

2010-01-01

PHE (Process Heat Exchanger) is a key component required to transfer heat energy of 950 .deg. C generated in a VHTR (Very High Temperature Reactor) to the chemical reaction that yields a large quantity of hydrogen. Korea Atomic Energy Research Institute established the helium gas loop for the performance test of components, which are used in the VHTR, and they manufactured a PHE prototype to be tested in the loop. In this study, as part of the high temperature structural-integrity evaluation of the PHE prototype, which is scheduled to be tested in the helium gas loop, we carried out high-temperature structural-analysis modeling, thermal analysis, and thermal expansion analysis of the PHE prototype. The results obtained in this study will be used to design the performance test setup for the PHE prototype

Pionic retardation effects in two-pion-exchange three-nucleon forces

International Nuclear Information System (INIS)

Coon, S.A.; Friar, J.L.

1986-01-01

Those two-pion-exchange three-nucleon forces which arise from nuclear processes that involve only pions and nucleons are calculated. Among the processes which contribute are pion seagulls (e.g., nucleon-antinucleon pair terms) and overlapping, retarded pion exchanges. The resulting potential is shown to be a (v/c) 2 relativistic correction, and satisfies nontrivial constraints from special relativity. The relativistic ambiguities found before in treatments of relativistic corrections to the one-pion-exchange nuclear charge operator and two-body potential are also present in the three-nucleon potential. The resulting three-nucleon force differs from the original Tucson-Melbourne potential only in the presence of several new nonlocal terms, and in the specification of the choice of ambiguity parameters in the latter potential

Pionic retardation effects in two-pion-exchange three-nucleon forces

Science.gov (United States)

Coon, S. A.; Friar, J. L.

1986-09-01

Those two-pion-exchange three-nucleon forces which arise from nuclear processes that involve only pions and nucleons are calculated. Among the processes which contribute are pion seagulls (e.g., nucleon-antinucleon pair terms) and overlapping, retarded pion exchanges. The resulting potential is shown to be a (v/c)2 relativistic correction, and satisfies nontrivial constraints from special relativity. The relativistic ambiguities found before in treatments of relativistic corrections to the one-pion-exchange nuclear charge operator and two-body potential are also present in the three-nucleon potential. The resulting three-nucleon force differs from the original Tucson-Melbourne potential only in the presence of several new nonlocal terms, and in the specification of the choice of ambiguity parameters in the latter potential.

Pionic retardation effects in two-pion-exchange three-nucleon forces

Energy Technology Data Exchange (ETDEWEB)

Coon, S.A.; Friar, J.L.

1986-09-01

Those two-pion-exchange three-nucleon forces which arise from nuclear processes that involve only pions and nucleons are calculated. Among the processes which contribute are pion seagulls (e.g., nucleon-antinucleon pair terms) and overlapping, retarded pion exchanges. The resulting potential is shown to be a (v-italic/c-italic)/sup 2/ relativistic correction, and satisfies nontrivial constraints from special relativity. The relativistic ambiguities found before in treatments of relativistic corrections to the one-pion-exchange nuclear charge operator and two-body potential are also present in the three-nucleon potential. The resulting three-nucleon force differs from the original Tucson-Melbourne potential only in the presence of several new nonlocal terms, and in the specification of the choice of ambiguity parameters in the latter potential.

Turbulent exchange processes of the planetary boundary layer - TUAREG

International Nuclear Information System (INIS)

Beier, N.; Weber, M.

1992-11-01

A mobile groundstation with associated sovftware has been developed to measure fluxes of properties and constituents, and the vertical distribution of chemically reactive trace gases. The significance and accuracy of the derived fluxes have been investigated. Within the validity of the meteorological assumptions used, the error is less than 10%. The turbulent vertical transport has been investigated over homogeneous areas in mixed heterogeneous terrain during four field experiments. The following results were obtained: characteristics of the structure of the turbulence - diurnal variations of the fluxes of momentum and energy - the vertical distribution of NO, NO 2 and O 3 -diurnal variations of their flux and deposition velocity - balance of ozone and exchange processes in the convective PBL. Correlation and profile measurements at a fixed point in mixed heterogeneous terrain are representative of the surface type, if the upwind dimension of the homogeneous areas is at least 500 m. If this is not the case, anisotropic and organized turbulence develops. Then the formally calculated fluxes arise, in part, due to random numbers and cannot be attributed to a local site. A definitive conclusion would require measurements of the three dimensional structure of turbulence. There are no counter-gradient fluxes in the nondivergent PBL. They arise from the use of inadequate integration intervals in correlation and profile calculations. In contrast, they do occur in regions of divergence. Since the similarity theory is not valid in this case, fluxes can be neither measured nor calculated. Airborne measurements were carried out by the ''Institut fuer Physik der Atmosphaere'', DLR. The following results are attached: the mean structure of the PBL - the turbulent fluxes of meteorological variables - the horizontal variability of the fluxes near the ground - the turbulent flux of ozone and the ozone balance. Comparisons with model calculations show good agreement. (orig./KW). 116

New anion-exchange polymers for improved separations

International Nuclear Information System (INIS)

Jarvinen, G.D.; Barr, M.E.; Marsh, S.F.

1997-01-01

Objective is to improve the understanding of how the structure of a new class of anion-exchange polymers controls the binding of anionic actinide complexes from solution. This is needed to develop practical separation systems that will reduce the cost of actinide processing operations within the DOE complex. In addition anion exchange is widely used in industry. Several new series of bifunctional anion- exchange polymers have been designed, synthesized, and tested for removing Pu(IV), Am(III), and U(VI) from nitric acid. The polymers contain a pyridinium site derived from the host poly(4-vinylpyridine) and a second cationic site attached through a chain of 2 to 6 methylene groups. The new polymers removed Pu four to ten times more efficiently than the best commercial materials

Unlocking Chain Exchange in Highly Amphiphilic Block Polymer Micellar Systems: Influence of Agitation.

Science.gov (United States)

Murphy, Ryan P; Kelley, Elizabeth G; Rogers, Simon A; Sullivan, Millicent O; Epps, Thomas H

2014-11-18

Chain exchange between block polymer micelles in highly selective solvents, such as water, is well-known to be arrested under quiescent conditions, yet this work demonstrates that simple agitation methods can induce rapid chain exchange in these solvents. Aqueous solutions containing either pure poly(butadiene- b -ethylene oxide) or pure poly(butadiene- b -ethylene oxide- d 4 ) micelles were combined and then subjected to agitation by vortex mixing, concentric cylinder Couette flow, or nitrogen gas sparging. Subsequently, the extent of chain exchange between micelles was quantified using small angle neutron scattering. Rapid vortex mixing induced chain exchange within minutes, as evidenced by a monotonic decrease in scattered intensity, whereas Couette flow and sparging did not lead to measurable chain exchange over the examined time scale of hours. The linear kinetics with respect to agitation time suggested a surface-limited exchange process at the air-water interface. These findings demonstrate the strong influence of processing conditions on block polymer solution assemblies.

Multiscale simulations of ligand adsorption and exchange on gold nanoparticles.

Science.gov (United States)

Gao, Hui-Min; Liu, Hong; Qian, Hu-Jun; Jiao, Gui-Sheng; Lu, Zhong-Yuan

2018-01-17

We have developed a multiscale model that combines first-principles methods with atomistic and mesoscopic simulations to explore the molecular structures and packing density of the ligands present on the gold nanoparticle (AuNP) surface, as well as the adsorption/exchange reaction kinetics of cetyltrimethylammonium bromide (CTAB)/PEG-SH ligands on different facets of gold, namely, Au(111), Au(100), and Au(110). Our model predicts that on clean gold surfaces, CTAB adsorption is diffusion limited. Specifically, CTAB has the preferentially higher adsorption rate and coverage density on Au(100) and Au(110) surfaces, forming a more compact layer with respect to that on the Au(111) surface, which could result in greater growth of gold nanoparticles along the (111) direction. As opposed to CTAB adsorption, the exchange reaction between PEG-SH with CTAB shows no selectivity to different crystal faces, and the reaction process follows Langmuir diffusion kinetics. Kinetic analysis reveals that, in water, the exchange reaction is zeroth order with respect to the concentration of an incoming PEG-SH, indicative of a dissociative exchange mechanism. The observed rate constant decreases exponentially with the PEG-SH chain length, consistent with a diffusion process for the free PEG-SH in water. In particular, we show that the exchange efficiency increases as the chain rigidness and size of the incoming ligand and/or steric bulk of the initial protecting ligand shell are decreased. Our objectives are to provide a model to assess the kinetics and thermodynamics of the adsorption/exchange reaction process, and we expect that these findings will have important implications for routine surface characterization of AuNPs.

Rheology Of Settled Solids In The Small Column Ion Exchange Process

International Nuclear Information System (INIS)

Poirier, M.; Ferguson, C.; Koopman, D.

2011-01-01

The Small Column Ion Exchange (SCIX) process is being developed to remove cesium, strontium, and actinides from Savannah River Site (SRS) Liquid Waste using an existing waste tank (i.e., Tank 41H) to house the process. This process adds monosodium titanate (MST) to a waste tank containing salt solution (and entrained sludge solids). While the process is operating, the solid particles will begin to settle at temperatures up to 45 C. Previous testing has shown that sludge-MST slurries that sit for extended periods (i.e., 1-61 days) at elevated temperatures (i.e., 23-80 C) can develop large shear strengths which could make them difficult to resuspend and remove from the tank. The authors are conducting rheological testing of mixtures containing various concentrations of sludge, MST, and crystalline silicotitanate (CST, ground and unground) that have been aged at different times (i.e., 0 to 13 weeks) and isothermally heated to 30, 45, or 60 C. Additional tests are being conducted that will allow the solid particles to settle at 45 C for 6, 12, and 24 months. The objectives of this task are to determine the impact of settling time and temperature on the shear strength, yield stress, and consistency of the slurries and to determine the impact of radiation on slurry rheology. The testing will determine the relative impact of these parameters rather than predict the shear strength, yield stress, and consistency as a function of feed and operating conditions. This document describes the rheology of slurries containing MST and simulated sludge that sat at elevated temperatures (i.e., up to 60 C) for up to 13 weeks. Rheology of CST-containing slurries, as well as results of the long term settling (6, 12, and 24 months) and irradiation tests (10 and 100 MRad), will be reported later. The conclusions from this analysis follow: (1) MST only slurries that sat at elevated temperatures had larger shear strength, yield stress, and consistency than MST plus sludge slurries that

RHEOLOGY OF SETTLED SOLIDS IN THE SMALL COLUMN ION EXCHANGE PROCESS

Energy Technology Data Exchange (ETDEWEB)

Poirier, M.; Ferguson, C.; Koopman, D.

2011-01-27

The Small Column Ion Exchange (SCIX) process is being developed to remove cesium, strontium, and actinides from Savannah River Site (SRS) Liquid Waste using an existing waste tank (i.e., Tank 41H) to house the process. This process adds monosodium titanate (MST) to a waste tank containing salt solution (and entrained sludge solids). While the process is operating, the solid particles will begin to settle at temperatures up to 45 C. Previous testing has shown that sludge-MST slurries that sit for extended periods (i.e., 1-61 days) at elevated temperatures (i.e., 23-80 C) can develop large shear strengths which could make them difficult to resuspend and remove from the tank. The authors are conducting rheological testing of mixtures containing various concentrations of sludge, MST, and crystalline silicotitanate (CST, ground and unground) that have been aged at different times (i.e., 0 to 13 weeks) and isothermally heated to 30, 45, or 60 C. Additional tests are being conducted that will allow the solid particles to settle at 45 C for 6, 12, and 24 months. The objectives of this task are to determine the impact of settling time and temperature on the shear strength, yield stress, and consistency of the slurries and to determine the impact of radiation on slurry rheology. The testing will determine the relative impact of these parameters rather than predict the shear strength, yield stress, and consistency as a function of feed and operating conditions. This document describes the rheology of slurries containing MST and simulated sludge that sat at elevated temperatures (i.e., up to 60 C) for up to 13 weeks. Rheology of CST-containing slurries, as well as results of the long term settling (6, 12, and 24 months) and irradiation tests (10 and 100 MRad), will be reported later. The conclusions from this analysis follow: (1) MST only slurries that sat at elevated temperatures had larger shear strength, yield stress, and consistency than MST plus sludge slurries that

The character of resonant charge exchange involving highly excited atoms

International Nuclear Information System (INIS)

Kosarim, A. V.; Smirnov, B. M.; Capitelli, M.; Laricchiuta, A.

2012-01-01

We study the process of resonant charge exchange involving excited helium atoms with the principal quantum number n = 5 colliding with the helium ion in the ground state in the collision energy range from thermal up to 10 eV. This information may be important for the analysis of planet atmospheres containing helium, in particular, for Jupiter’s atmosphere, but our basic interest is the transition from the quantum to classical description of this process, where, due to large cross sections, evaluations of the cross sections are possible. For the chosen process, quantum theory allows determining the cross section as a result of a tunnel electron transition, while classical theory accounts for over-barrier electron transitions. The classical theory additionally requires effective transitions between states with close energies. The analysis of these transitions for helium with n = 5 shows that electron momenta and their projections are mixed for a part of the states, while for other states, the mixing is absent. A simple criterion to separate such states is given. In addition, the main contribution to the cross section of resonant charge exchange follows from tunnel electron transitions. As a result, the quantum theory is better for calculating the cross sections of resonant charge exchange than the classical one and also allows finding the partial cross sections of resonant charge exchange, while the classical approach gives the cross section of resonant charge exchange in a simple manner with the accuracy of 20%.

Contributions of chemical and diffusive exchange to T1ρ dispersion.

Science.gov (United States)

Cobb, Jared Guthrie; Xie, Jingping; Gore, John C

2013-05-01

Variations in local magnetic susceptibility may induce magnetic field gradients that affect the signals acquired for MR imaging. Under appropriate diffusion conditions, such fields produce effects similar to slow chemical exchange. These effects may also be found in combination with other chemical exchange processes at multiple time scales. We investigate these effects with simulations and measurements to determine their contributions to rotating frame (R1ρ ) relaxation in model systems. Simulations of diffusive and chemical exchange effects on R1ρ dispersion were performed using the Bloch equations. Additionally, R1ρ dispersion was measured in suspensions of Sephadex and latex beads with varying spin locking fields at 9.4 T. A novel analysis method was used to iteratively fit for apparent chemical and diffusive exchange rates with a model by Chopra et al. Single- and double-inflection points in R1ρ dispersion profiles were observed, respectively, in simulations of slow diffusive exchange alone and when combined with rapid chemical exchange. These simulations were consistent with measurements of R1ρ in latex bead suspensions and small-diameter Sephadex beads that showed single- and double-inflection points, respectively. These observations, along with measurements following changes in temperature and pH, are consistent with the combined effects of slow diffusion and rapid -OH exchange processes. Copyright © 2012 Wiley Periodicals, Inc.

Exploration of overloaded cation exchange chromatography for monoclonal antibody purification.