The use of radioisotope tracers in the metallurgical industries

International Nuclear Information System (INIS)

Easey, J.F.

1987-01-01

Radioisotope techniques have been widely used in the metallurgical industries for many years. They have been shown to be very suitable for studying large scale plant and, in many cases, they are the most suitable techniques for such investigations. Applications of radioisotope tracers to some specific metallurgical problems are discussed. (author)

New radionuclide specific laboratory detection system for metallurgical industry

International Nuclear Information System (INIS)

Burianova, L.; Solc, J.; Dryak, P.; Moser, H.; Branger, T.; Garcia-Torano, E.; Peyres, V.; Capogni, M.; Luca, A.; Vodenik, B.; Oliveira, C.; Portugal, L.; Tzika, F.; Lutter, G.; Szucs, L.; Dziel, T.; Burda, O.; Dirk, A.; Martinkovic, J.; Sliskonen, T.; Mattila, A.

2014-01-01

One of the main outputs of the European Metrology Research Programme (EMRP) project 'Ionising radiation metrology for the metallurgical industry' (MetroMetal) was the recommendation on a novel spectrometric detection system optimized for the measurement of radioactivity in metallurgical samples. The recommended system, prototypes of which were constructed at two project partner's laboratories, was characterized by using Monte Carlo (MC) simulations. Six different MC codes were used to model the system and a range of cylindrical samples of cast steel, slag and fume dust. The samples' shape, density, and elemental composition were the same as the ones of the calibration standards developed within the project to provide traceability to end-users. The MC models were used to calculate full-energy peak and total detection efficiencies as well as true coincidence summing correction (TCSC) factors for selected radionuclides of interest in the metallurgical industry: 60 Co, 137 Cs, 192 Ir, 214 Bi, 214 Pb, and 208 Tl. The MC codes were compared to each other on the basis of the calculated detection efficiencies and TCSC factors. In addition, a 'Procedural guide for calculation of TCSC factors for samples in metallurgical industry' was developed for end-users. The TCSC factors reached in certain cases up to 32% showing that the summing effects are of high importance in the close measurement geometries met in routine analysis of metallurgical samples. (authors)

Soft restructuring process in metallurgical enterprises in Poland

Directory of Open Access Journals (Sweden)

B. Gajdzik

2015-10-01

Full Text Available This article presents the range and outcomes of soft restructuring in metallurgical enterprises in Poland. The term ‘soft restructuring’ applies to changes in metallurgical enterprises’ employment policy during the period of political transformation in Poland. Steelworks performance under the market economy conditions demanded introducing changes in staff resources. Changes referred both to the staff structure as well as employees’ skills and gradual engaging of the staff in building the steelworks’ competitive advantage.

Energy-dissipation-model for metallurgical multi-phase-systems

Energy Technology Data Exchange (ETDEWEB)

Mavrommatis, K.T. [Rheinisch-Westfaelische Technische Hochschule Aachen, Aachen (Germany)

1996-12-31

Entropy production in real processes is directly associated with the dissipation of energy. Both are potential measures for the proceed of irreversible processes taking place in metallurgical systems. Many of these processes in multi-phase-systems could then be modelled on the basis of the energy-dissipation associated with. As this entity can often be estimated using very simple assumptions from first principles, the evolution of an overall measure of systems behaviour can be studied constructing an energy-dissipation -based model of the system. In this work a formulation of this concept, the Energy-Dissipation-Model (EDM), for metallurgical multi-phase-systems is given. Special examples are studied to illustrate the concept, and benefits as well as the range of validity are shown. This concept might be understood as complement to usual CFD-modelling of complex systems on a more abstract level but reproducing essential attributes of complex metallurgical systems. (author)

Energy-dissipation-model for metallurgical multi-phase-systems

Energy Technology Data Exchange (ETDEWEB)

Mavrommatis, K T [Rheinisch-Westfaelische Technische Hochschule Aachen, Aachen (Germany)

1997-12-31

Entropy production in real processes is directly associated with the dissipation of energy. Both are potential measures for the proceed of irreversible processes taking place in metallurgical systems. Many of these processes in multi-phase-systems could then be modelled on the basis of the energy-dissipation associated with. As this entity can often be estimated using very simple assumptions from first principles, the evolution of an overall measure of systems behaviour can be studied constructing an energy-dissipation -based model of the system. In this work a formulation of this concept, the Energy-Dissipation-Model (EDM), for metallurgical multi-phase-systems is given. Special examples are studied to illustrate the concept, and benefits as well as the range of validity are shown. This concept might be understood as complement to usual CFD-modelling of complex systems on a more abstract level but reproducing essential attributes of complex metallurgical systems. (author)

Evolving dynamics of trading behavior based on coordination game in complex networks

Science.gov (United States)

Bian, Yue-tang; Xu, Lu; Li, Jin-sheng

2016-05-01

This work concerns the modeling of evolvement of trading behavior in stock markets. Based on the assumption of the investors' limited rationality, the evolution mechanism of trading behavior is modeled according to the investment strategy of coordination game in network, that investors are prone to imitate their neighbors' activity through comprehensive analysis on the risk dominance degree of certain investment behavior, the network topology of their relationship and its heterogeneity. We investigate by mean-field analysis and extensive simulations the evolution of investors' trading behavior in various typical networks under different risk dominance degree of investment behavior. Our results indicate that the evolution of investors' behavior is affected by the network structure of stock market and the effect of risk dominance degree of investment behavior; the stability of equilibrium states of investors' behavior dynamics is directly related with the risk dominance degree of some behavior; connectivity and heterogeneity of the network plays an important role in the evolution of the investment behavior in stock market.

Real-time visualization of soliton molecules with evolving behavior in an ultrafast fiber laser

Science.gov (United States)

Liu, Meng; Li, Heng; Luo, Ai-Ping; Cui, Hu; Xu, Wen-Cheng; Luo, Zhi-Chao

2018-03-01

Ultrafast fiber lasers have been demonstrated to be great platforms for the investigation of soliton dynamics. The soliton molecules, as one of the most fascinating nonlinear phenomena, have been a hot topic in the field of nonlinear optics in recent years. Herein, we experimentally observed the real-time evolving behavior of soliton molecule in an ultrafast fiber laser by using the dispersive Fourier transformation technology. Several types of evolving soliton molecules were obtained in our experiments, such as soliton molecules with monotonically or chaotically evolving phase, flipping and hopping phase. These results would be helpful to the communities interested in soliton nonlinear dynamics as well as ultrafast laser technologies.

Cleaner metallurgical industry in Serbia: a road to the sustainable development

Directory of Open Access Journals (Sweden)

D. Panias

2009-01-01

Full Text Available Since the sustainable development has been a global and fundamental objecttive, a metallurgical industrial sector faces some of the most difficult sustainability challenges of any industrial sector. On the other hand, the metallurgical production in Serbia is a very important part of the economy. Due to present facilities and technologies, metallurgical companies face a great challenge to fulfill the requirements introduced by legislature referring to the cleaner production and sustainable development. The state of art in the production, facilities, pollution with some answers to imposed challenges is presented.

Job Prospects for Metallurgical Engineering.

Science.gov (United States)

Basta, Nicholas

1985-01-01

Job prospects in mining, metal-extraction, steel, and refining industries are depressed, but technological discoveries are opening up new fields for metallurgical engineers. Enrollment/employment opportunities and salaries in these areas are discussed a well as the roles of foreign competition, plastics applications, and ceramics research and…

Diagnosis of employee engagement in metallurgical enterprise

Directory of Open Access Journals (Sweden)

B. Gajdzik

2013-01-01

Full Text Available In the theoretical part of the publication an overview of the definitions of employee engagement was conducted together with the analysis of the methods and techniques which influence the professional activity of the employees in the metallurgical enterprise. The practical part discusses the results of diagnosis of engagement in steelworks. Presented theories, as well as the research, fill the information gap concerning the engagement of the employees in metallurgical enterprises. This notion is important due to the fact that modern conditions of human resources management require the engagement of the employees as something commonly accepted and a designation of manufacturing enterprises.

Effect of metallurgical variables on environmental fracture of steels

Energy Technology Data Exchange (ETDEWEB)

Bernstein, I M; Thompson, A W

1976-12-01

The susceptibility of iron alloys, in particular, steels, to hydrogen embrittlement is examined. It is demonstrated by a review of available data on metallurgically well-characterized alloys that the nature and extent of hydrogen susceptibility are sensitive and often predictable functions of such metallurgical variables as composition, grain size, texture, microstructure, and thermal treatment. Specifically, solutes such as carbon and manganese are shown to be capable of leading to a degradation of performance in hydrogen, whereas silicon and titanium are often beneficial additions. Microstructures at equivalent strength levels are ranked in order of susceptibility; generally, a refined substructure gives the best results. The role of heat treatment in controlling the hydrogen-induced crack path and its relationship to thermal embrittlement phenomena are stressed. Finally, possible hydrogen embrittlement mechanisms are assessed in terms of the critical roles of metallurgical variables in the embrittlement.

Cermet crucible for metallurgical processing

Science.gov (United States)

Boring, Christopher P.

1995-01-01

A cermet crucible for metallurgically processing metals having high melting points comprising a body consisting essentially of a mixture of calcium oxide and erbium metal, the mixture comprising calcium oxide in a range between about 50 and 90% by weight and erbium metal in a range between about 10 and 50% by weight.

Estimation of metallurgical parameters of flotation process from froth visual features

Directory of Open Access Journals (Sweden)

Mohammad Massinaei

2015-06-01

Full Text Available The estimation of metallurgical parameters of flotation process from froth visual features is the ultimate goal of a machine vision based control system. In this study, a batch flotation system was operated under different process conditions and metallurgical parameters and froth image data were determined simultaneously. Algorithms have been developed for measuring textural and physical froth features from the captured images. The correlation between the froth features and metallurgical parameters was successfully modeled, using artificial neural networks. It has been shown that the performance parameters of flotation process can be accurately estimated from the extracted image features, which is of great importance for developing automatic control systems.

Evolvability Search: Directly Selecting for Evolvability in order to Study and Produce It

DEFF Research Database (Denmark)

Mengistu, Henok; Lehman, Joel Anthony; Clune, Jeff

2016-01-01

of evolvable digital phenotypes. Although some types of selection in evolutionary computation indirectly encourage evolvability, one unexplored possibility is to directly select for evolvability. To do so, we estimate an individual's future potential for diversity by calculating the behavioral diversity of its...... immediate offspring, and select organisms with increased offspring variation. While the technique is computationally expensive, we hypothesized that direct selection would better encourage evolvability than indirect methods. Experiments in two evolutionary robotics domains confirm this hypothesis: in both...... domains, such Evolvability Search produces solutions with higher evolvability than those produced with Novelty Search or traditional objective-based search algorithms. Further experiments demonstrate that the higher evolvability produced by Evolvability Search in a training environment also generalizes...

Study of a metallurgical site in Tuscany (Italy) by radiocarbon dating

International Nuclear Information System (INIS)

Cartocci, A.; Fedi, M.E.; Taccetti, F.; Benvenuti, M.; Chiarantini, L.; Guideri, S.

2007-01-01

Tuscany represents one of the most important ancient mining districts of Italy. Metalworking activities have been present in the area since ancient times and several mining centres have been active in the region since the Etruscan period. Two of the more notable mining locations are the island of Elba and the towns of Populonia and Massa Marittima. In order to reconstruct the development of metallurgical techniques in the past, a multi-disciplinary approach is required, involving both archaeological study and archaeometric analysis of the sites of interest. One of the most complex problems is establishing the chronological history of metallurgical exploitation in ancient sites: archaeological remains are sometimes incomplete and the stratigraphy of archaeological horizons might have been deeply altered. Thus, direct dating of metallurgical slags and other remains of mining and metalworking activities using radiocarbon measurements is particularly useful for developing site chronologies. Charcoal samples from a recent excavation in Populonia were dated by AMS radiocarbon in order to reconstruct the chronological evolution of ancient metallurgical production; results reported here are consistent with archaeological observations

Study of a metallurgical site in Tuscany (Italy) by radiocarbon dating

Energy Technology Data Exchange (ETDEWEB)

Cartocci, A. [Dipartimento di Fisica dell' Universita e I.N.F.N. Sezione di Firenze, via Sansone 1, 50019 Sesto Fiorentino, Florence (Italy); Fedi, M.E. [Dipartimento di Fisica dell' Universita e I.N.F.N. Sezione di Firenze, via Sansone 1, 50019 Sesto Fiorentino, Florence (Italy)]. E-mail: fedi@fi.infn.it; Taccetti, F. [Dipartimento di Fisica dell' Universita e I.N.F.N. Sezione di Firenze, via Sansone 1, 50019 Sesto Fiorentino, Florence (Italy); Benvenuti, M. [Dipartimento di Scienze della Terra dell' Universita di Firenze, via La Pira 4, 50121 Florence (Italy); Chiarantini, L. [Dipartimento di Scienze della Terra dell' Universita di Firenze, via La Pira 4, 50121 Florence (Italy); Guideri, S. [Societa Parchi Val di Cornia S.p.a., via G. Lerario, Piombino, Livorno (Italy)

2007-06-15

Tuscany represents one of the most important ancient mining districts of Italy. Metalworking activities have been present in the area since ancient times and several mining centres have been active in the region since the Etruscan period. Two of the more notable mining locations are the island of Elba and the towns of Populonia and Massa Marittima. In order to reconstruct the development of metallurgical techniques in the past, a multi-disciplinary approach is required, involving both archaeological study and archaeometric analysis of the sites of interest. One of the most complex problems is establishing the chronological history of metallurgical exploitation in ancient sites: archaeological remains are sometimes incomplete and the stratigraphy of archaeological horizons might have been deeply altered. Thus, direct dating of metallurgical slags and other remains of mining and metalworking activities using radiocarbon measurements is particularly useful for developing site chronologies. Charcoal samples from a recent excavation in Populonia were dated by AMS radiocarbon in order to reconstruct the chronological evolution of ancient metallurgical production; results reported here are consistent with archaeological observations.

Flow behavior and microstructures of powder metallurgical CrFeCoNiMo0.2 high entropy alloy during high temperature deformation

Energy Technology Data Exchange (ETDEWEB)

Wang, Jiawen [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Liu, Yong, E-mail: yonliu@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Liu, Bin, E-mail: binliu@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Wang, Yan [School of Aeronautics and Astronautics, Central South University, Changsha 410083 (China); Cao, Yuankui; Li, Tianchen; Zhou, Rui [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China)

2017-03-24

Dynamic recrystallization (DRX) refine grains of high entropy alloys (HEAs) and significant improve the mechanical property of HEAs, but the effect of high melting point element molybdenum (Mo) on high temperature deformation behavior has not been fully understood. In the present study, flow behavior and microstructures of powder metallurgical CrFeCoNiMo{sub 0.2} HEA were investigated by hot compression tests performed at temperatures ranging from 700 to 1100 °C with strain rates from 10{sup −3} to 1 s{sup −1}. The Arrhenius constitutive equation with strain-dependent material constants was used for modeling and prediction of flow stress. It was found that at 700 °C, the dynamic recovery is the dominant softening mechanism, whilst with the increase in compression testing temperature, the DRX becomes the dominant mechanism of softening. In the present HEA, the addition of Mo results in the high activation energy (463 kJ mol{sup −1}) and the phase separation during hot deformation. The formation of Mo-rich σ phase particles pins grain boundary migration during DRX, and therefore refines the size of recrystallized grains.

Partially satisfied to fully satisfied transitions in co-evolving inverse voter model and possible scaling behavior

International Nuclear Information System (INIS)

Choi, C.W.; Xu, C.; Hui, P.M.

2015-01-01

Understanding co-evolving networks characterized by the mutual influence of agents' actions and network structure remains a challenge. We study a co-evolving inverse voter model in which agents adapt to achieve a preferred environment with more opposite-opinion neighbors by rewiring their connections and switching opinion. Numerical studies reveal a transition from a dynamic partially satisfied phase to a frozen fully satisfied phase as the rewiring probability is varied. A simple mean field theory is shown to capture the behavior only qualitatively. An improved mean field theory carrying a longer spatial correlation gives better results. Motivated by numerical results in networks of different degrees and mean field results, we propose a scaling variable that combines the rewiring probability and mean degree in a special form. The scaling variable is shown to work well in analyzing data corresponding to different networks and different rewiring probabilities. An application is to predict the results for networks of different degrees based solely on results obtained from networks of one degree. Studying scaling behavior provides an alternative path for understanding co-evolving agent-based dynamical systems, especially in light of the trade-off between complexity of a theory and its accuracy. - Highlights: • Identified key features and phase transitions in coevolving inverse voter model. • Constructed a better theory incorporating longer spatial correlation. • Proposed scaling variable and illustrated possible scaling behavior. • Used scaling behavior to predict results of IVM in a different network.

TMI-2 Vessel Investigation Project Metallurgical Program

International Nuclear Information System (INIS)

Diercks, D.R.; Neimark, L.A.

1990-01-01

The TMI-2 [Three Mile Island unit 2] Vessel Investigation Project Metallurgical Program at Argonne National Laboratory is a part of the international TMI-2 Vessel Investigation Project being conducted jointly by the U.S. Nuclear Regulatory Commission and the Organization for Economic Co-operation and Development (OECD). The overall project consists of three phases, namely (1) recovery of material samples from the lower head of the TMI-2 reactor, (2) examination and analysis of the lower head samples and the preparation and testing of archive material subjected to a similar thermal history, and (3) procurement, examination, and analysis of companion core material located adjacent to or near the lower head material. The specific objectives of the ANL Metallurgical Program, which accounts for a major portion of Phase 2, are to prepare metallographic and mechanical test specimen blanks from the TMI-2 lower head material, prepare similar test specimen blanks from suitable archive material subjected to the appropriate thermal processing, determine the mechanical properties of the lower vessel head and archive materials under the conditions of the core-melt accident, and assess the lower head integrity and margin-to-failure during the accident. The ANL work consists of three tasks: (1) archive materials program, (2) fabrication of metallurgical and mechanical test specimens from the TMI-2 pressure vessel samples, and (3) mechanical property characterization of TMI-2 lower pressure vessel head and archive material

ORNL evaluation of the ORR-PSF metallurgical experiment and blind test

International Nuclear Information System (INIS)

Stallmann, F.W.

1984-01-01

A methodology is described to evaluate the dosimetry and metallurgical data from the two-year ORR-PSF metallurgical irradiation experiment. The first step is to obtain a three-dimensional map of damage exposure parameter values based on neutron transport calculations and dosimetry measurements which are obtained by means of the LSL-M2 adjustment procedure. Metallurgical test data are then combined with damage parameter, temperature, and chemistry information to determine the correlation between radiation and steel embrittlement in reactor pressure vessels including estimates for the uncertainties. Statistical procedures for the evaluation of Charpy data, developed earlier, are used for this investigation. The data obtained in this investigation provide a benchmark against which the predictions of the PSF Blind Test can be compared. The results of this investigation and the Blind Test comparison are discussed

Energy conservation and efficiency in Giprokoks designs at Ukrainian ferrous-metallurgical enterprises

Energy Technology Data Exchange (ETDEWEB)

M.I. Fal' kov [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

2009-07-15

Energy conditions at Ukrainian ferrous-metallurgical enterprises are analyzed. Measures to boost energy conservation and energy efficiency are proposed: specifically, the introduction of systems for dry slaking of coke; and steam-gas turbines that employ coke-oven gas or a mixture of gases produced at metallurgical enterprises. Such turbines may be built from Ukrainian components.

Utilisation of metallurgical by-products in road construction in the Czech Republic

Science.gov (United States)

Kresta, František

2017-09-01

Metallurgical by-products, primarily blast furnace slag and steel slag, have ranked among important alternative sources of fill as well as of material for the structural layers in highways. Main hazards of metallurgical by-products are closely connected to their chemical and mineralogical composition and they can be resulted in volume changes. Fears from possible deformations similar to the D47 motorway meant that metallurgical by-products were excluded from several public tenders of road construction. Comparison of blast furnace slag, steel slag and other metallurgical by products parameters allow us to define the most hazardous material as steelworks waste. Linear swelling of steelwork waste achieves more than 40% at 75°C and swelling pressure was higher than 1.5 MPa. Compositional heterogeneity of steelworks waste makes it difficult to establish the long-term behaviour of this material. At the present time we cannot ascertain which maximum values can be reached by deformation and what are the swelling pressures acting on the material while the volume changes are in progress.

Cyril Stanley Smith's Translations of Metallurgical Classics

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 11; Issue 6. Cyril Stanley Smith's Translations of Metallurgical Classics. Martha Goodway. General Article Volume 11 Issue 6 June 2006 pp 63-66. Fulltext. Click here to view fulltext PDF. Permanent link:

7th european metallurgical conference EMC 2013

Directory of Open Access Journals (Sweden)

Srećko R. Stopić

2014-02-01

Full Text Available From June 23 – 26, 2013, the GDMB Society for Mining, Metallurgy, Resource and Environmental Technology organized 7th European Metallurgical Conference (EMC 2013 in Weimar, Germany. The previous European metallurgical conferences were organized by  the GDMB in Friedrichshafen (2001, Hanover (2003, Leipzig (2005, Duesseldorf (2007, Innsbruck (2009, and Duesseldorf (2011. The GDMB is a non-profit organization from Clausthal, Germany,,focused on combining science with practical experience in metallurgy, mining, materials engineering, mineral processing, recycling and refining of metals, and  manufacturing of semi- and finishing products. The European Metallurgical conference EMC is one of the most well-known conferences worldwide in the field of non-ferrous metallurgy and is attended regularly by decision makers from industry and universities. The scientific program contained 6 plenary lectures and more than 130 presentations. An extensive poster exhibition was held, during which the authors had an opportunity to introduce their posters to the entire plenum as a part of a brief presentation., The € 500 worth “Poster Award EMC 2011 was awarded to Christoph Pichler from the Montan-University in Leoben, Austria. Not only the most important European countries were represented here, but also more than one third of the lecturers were from countries outside Europe (Canada, Japan, China, USA, South Africa, Australia. The origin of the participants reflects the aim of the organizers: to make this conference a worldwide platform for the scientific exchange of experience and information. The scientific presentations of the conference are presented in Proceedings: Vol. 1: Copper, Precious Metals, Waste effluents Treatment/ Biohydrometallurgical applications; Process Metallurgy, Bridging Non-Ferrous and Ferrous Metallurgy; Vol. 2: Lead and Zinc, Light metals, Sustainable technologies, Sustainable of non-ferrous metals production, Process Control

Centrifugal Casting Features/Metallurgical Characterization of Aluminum Alloys

International Nuclear Information System (INIS)

Chirita, G.; Soares, D.; Cruz, D.; Silva, F. S.; Stefanescu, I.

2008-01-01

This paper deals with the study of centrifugal effects on aluminium castings under high G values. Most of the studies in this domain (FGMs obtained by centrifugal casting) deal with functionally graded composites reinforced with a solid phase such as silicon particles or others. However, in this study it will be shown that unreinforced aluminium alloys may be significantly influenced by the centrifugal effect and that functionally graded castings are also obtained. It has been observed that the centrifugal effect may increase in some alloys, depending on the relative position in the castings, the rupture strength by approx. 50%, and rupture strain by about 300%, as compared to the gravity casting technique. The Young's modulus may also increase by about 20%. It has also been reported that in vertical centrifugal castings there are mainly three aspects that affect the components thus obtained, namely: fluid dynamics; vibration (inherent to the system); and centrifugal force. These features have a different effect on the castings depending on the aluminium alloy. In this paper, an analysis of the most important effects of the centrifugal casting process on metallurgical features is conducted. A solidification characterization at several points along the mould will be made in order to have an accurate idea of both the fluid dynamics inside the mould during the casting and the solidification behavior in different parts of the component. These two analyses will be related to the metallurgical properties (phase distribution; SDAS; eutectic silicon content and shape, pores density and shape) along the component and mainly along the direction of the centrifugal pressure. A comparison between castings obtained by both centrifugal casting technique and gravity casting technique is made for reference (gravity casting)

Metallurgical Evaluation of the Five-Inch Cylindrical Induction Melter

International Nuclear Information System (INIS)

Imrich, K.J.

2000-01-01

A metallurgical evaluation of the 5-inch cylindrical induction melter (CIM) vessel was performed by the Materials Technology Section to evaluate the metallurgical condition after operating for approximately 375 hours at 1400 to 1500 Degrees Celsius during a 2 year period. Results indicate that wall thinning and significant grain growth occurred in the lower portion of the conical section and the drain tube. No through-wall penetrations were found in the cylindrical and conical sections of the CIM vessel and only one leak site was identified in the drain tube. Failure of the drain tube was associated with a localized over heating and intercrystalline fracture

TMI-2 Vessel Investigation Project (VIP) Metallurgical Program

International Nuclear Information System (INIS)

Diercks, D.R.; Neimark, L.A.

1990-06-01

The TMI-2 Vessel Investigation Project (VIP) Metallurgical Program is a part of the international TMI-2 Vessel Investigation Project being conducting jointly by the US Nuclear Regulatory Commission and the Organization for Economic Co-operation and Development (OECD). The overall project consists of three phases, namely (1) recovery of material samples from the lower head of the TMI-2 reactor, (2) examination and analysis of the lower head samples and the preparation and testing of archive material subjected to a similar thermal history, and (3) procurement, examination, and analysis of companion core material located adjacent to or near the lower head material. The specific objectives of the ANL Metallurgical Program, which comprises a major portion of Phase 2, are to prepare metallographic and mechanical test specimen blanks from the TMI-2 lower head material, prepare similar test specimen blanks from suitable archive material subjected to the appropriate thermal processing, determine the mechanical properties of the lower vessel head and archive materials under the conditions of the core-melt accident, and assess the lower head integrity and margin-to-failure during the accident. The ANL work consists of three tasks: (1) archive materials program, (2) fabrication of metallurgical and mechanical test specimens from the TMI-2 pressure vessel samples, and (3) mechanical property characterization of TMI-2 lower pressure vessel head and archive material

Metallurgical plasma torches

International Nuclear Information System (INIS)

Shapovalov, V.A.; Latash, Yu.V.

2000-01-01

The technological equipment for the plasma heating of metals, plasma melting and plasma treatment of the surface is usually developed on the basis of are plasma torches using direct or alternating current. The reasons which partly restrict the industrial application of the plasma torches are the relatively short service life of the electrode (cathode) on which the arc is supported, and the contamination of the treated metal with the products of failure of the electrode. The aim of this work was to determine the reasons for the occurrence of negative phenomena observed in the process of service of plasma torches, and propose suitable approaches to the design of metallurgical plasma torches characterised by a long service life

Supercritical water oxidation benchscale testing metallurgical analysis report

International Nuclear Information System (INIS)

Norby, B.C.

1993-02-01

This report describes metallurgical evaluation of witness wires from a series of tests using supercritical water oxidation (SCWO) to process cutting oil containing a simulated radionuclide. The goal of the tests was to evaluate the technology's ability to process a highly chlorinated waste representative of many mixed waste streams generated in the DOE complex. The testing was conducted with a bench-scale SCWO system developed by the Modell Development Corporation. Significant test objectives included process optimization for adequate destruction efficiency, tracking the radionuclide simulant and certain metals in the effluent streams, and assessment of reactor material degradation resulting from processing a highly chlorinated waste. The metallurgical evaluation described herein includes results of metallographic analysis and Scanning Electron Microscopy analysis of witness wires exposed to the SCWO environment for one test series

Numerical computation of fluid flow in different nonferrous metallurgical reactors

International Nuclear Information System (INIS)

Lackner, A.

1996-10-01

Heat, mass and fluid flow phenomena in metallurgical reactor systems such as smelting cyclones or electrolytic cells are complex and intricately linked through the governing equations of fluid flow, chemical reaction kinetics and chemical thermodynamics. The challenges for the representation of flow phenomena in such reactors as well as the transfers of these concepts to non-specialist modelers (e.g. plant operators and management personnel) can be met through scientific flow visualization techniques. In the first example the fluid flow of the gas phase and of concentrate particles in a smelting cyclone for copper production are calculated three dimensionally. The effect of design parameters (length and diameter of reactor, concentrate feeding tangentially or from the top, ..) and operating conditions are investigated. Single particle traces show, how to increase particle retention time before the particles reach the liquid film flowing down the cyclone wall. Cyclone separators are widely used in the metallurgical and chemical industry for collection of large quantities of dust. Most of the empirical models, which today are applied for the design, are lacking in being valid in the high temperature region. Therefore the numerical prediction of the collection efficiency of dust particles is done. The particle behavior close to the wall is considered by applying a particle restitution model, which calculates individual particle restitution coefficients as functions of impact velocity and impact angle. The effect of design parameters and operating are studied. Moreover, the fluid flow inside a copper refining electrolysis cell is modeled. The simulation is based on density variations in the boundary layer at the electrode surface. Density and thickness of the boundary layer are compared to measurements in a parametric study. The actual inhibitor concentration in the cell is calculated, too. Moreover, a two-phase flow approach is developed to simulate the behavior of

Towards Representative Metallurgical Sampling and Gold Recovery Testwork Programmes

Directory of Open Access Journals (Sweden)

Simon C. Dominy

2018-05-01

Full Text Available When developing a process flowsheet, the risks in achieving positive financial outcomes are minimised by ensuring representative metallurgical samples and high quality testwork. The quality and type of samples used are as important as the testwork itself. The key characteristic required of any set of samples is that they represent a given domain and quantify its variability. There are those who think that stating a sample(s is representative makes it representative without justification. There is a need to consider both (1 in-situ and (2 testwork sub-sample representativity. Early ore/waste characterisation and domain definition are required, so that sampling and testwork protocols can be designed to suit the style of mineralisation in question. The Theory of Sampling (TOS provides an insight into the causes and magnitude of errors that may occur during the sampling of particulate materials (e.g., broken rock and is wholly applicable to metallurgical sampling. Quality assurance/quality control (QAQC is critical throughout all programmes. Metallurgical sampling and testwork should be fully integrated into geometallurgical studies. Traditional metallurgical testwork is critical for plant design and is an inherent part of geometallurgy. In a geometallurgical study, multiple spatially distributed small-scale tests are used as proxies for process parameters. These will be validated against traditional testwork results. This paper focusses on sampling and testwork for gold recovery determination. It aims to provide the reader with the background to move towards the design, implementation and reporting of representative and fit-for-purpose sampling and testwork programmes. While the paper does not intend to provide a definitive commentary, it critically assesses the hard-rock sampling methods used and their optimal collection and preparation. The need for representative sampling and quality testwork to avoid financial and intangible losses is

LWR surveillance dosimetry improvement program: PSF metallurgical blind test results

International Nuclear Information System (INIS)

Kam, F.B.K.; Maerker, R.E.; Stallmann, F.W.

1984-01-01

The metallurgical irradiation experiment at the Oak Ridge Research Reactor Poolside Facility (ORR-PSF) was designed as a benchmark to test the accuracy of radiation embrittlement predictions in the pressure vessel wall of light water reactors on the basis of results from surveillance capsules. The PSF metallurgical Blind Test is concerned with the simulated surveillance capsule (SSC) and the simulated pressure vessel capsule (SPVC). The data from the ORR-PSF benchmark experiment are the basis for comparison with the predictions made by participants of the metallurgical ''Blind Test''. The Blind Test required the participants to predict the embrittlement of the irradiated specimen based only on dosimetry and metallurgical data from the SSC1 capsule. This exercise included both the prediction of damage fluence and the prediction of embrittlement based on the predicted fluence. A variety of prediction methodologies was used by the participants. No glaring biases or other deficiencies were found, but neither were any of the methods clearly superior to the others. Closer analysis shows a rather complex and poorly understood relation between fluence and material damage. Many prediction formulas can give an adequate approximation, but further improvement of the prediction methodology is unlikely at this time given the many unknown factors. Instead, attention should be focused on determining realistic uncertainties for the predicted material changes. The Blind Test comparisons provide some clues for the size of these uncertainties. In particular, higher uncertainties must be assigned to materials whose chemical composition lies outside the data set for which the prediction formula was obtained. 16 references, 14 figures, 5 tables

Bankruptcy risk forecasting for the metallurgical branch in Romania

Directory of Open Access Journals (Sweden)

P. R. Răchişan

2014-07-01

Full Text Available All investment decisions require a thorough analysis of the retrospective evolution of the entities from the concerned area, in order to estimate the long-term evolution perspectives. In this context, the present study analyzes the evolution of the entities from the Romanian metallurgical sector based on the accounting and financial information published for the period 2008 - 2012 and, in fact, it justifies the situation from the perspective of users (managers, investors, auditors and of the economic environment specific to Romania. Starting from this premise we created a regression model particularly useful in forecasting the evolution of the ability to deal with debt for the entities from the Romanian metallurgical sector.

Elaboration and characterization of metallurgical silicon for photovoltaic applications

International Nuclear Information System (INIS)

Barbouche, M; Hajji, M; Krout, F; Ezzaouia, H

2015-01-01

There is a small quantity of participants in the global market of silicon, mainly from the developed countries. It should be noticed also that production of metallurgical silicon Mg-Si is among the most important steps to produce solar grade silicon and photovoltaic panels. Therefore, in this paper we focused on the growth of Mg-Si by carbothermal reduction of silica. An investigation was made using FT-IR characterization to study the effect of process conditions (temperature, atmosphere, duration) in Mg-Si production. Raman spectroscopy was used to investigate the produced Mg-Si. Based on these results, we established a pilot line production of metallurgical silicon at the 'CRTEn' in Tunisia

Fundamental metallurgical aspects of axial splitting in zircaloy cladding

International Nuclear Information System (INIS)

Chung, H. M.

2000-01-01

Fundamental metallurgical aspects of axial splitting in irradiated Zircaloy cladding have been investigated by microstructural characterization and analytical modeling, with emphasis on application of the results to understand high-burnup fuel failure under RIA situations. Optical microscopy, SEM, and TEM were conducted on BWR and PWR fuel cladding tubes that were irradiated to fluence levels of 3.3 x 10 21 n cm -2 to 5.9 x 10 21 n cm -2 (E > 1 MeV) and tested in hot cell at 292--325 C in Ar. The morphology, distribution, and habit planes of macroscopic and microscopic hydrides in as-irradiated and posttest cladding were determined by stereo-TEM. The type and magnitude of the residual stress produced in association with oxide-layer growth and dense hydride precipitation, and several synergistic factors that strongly influence axial-splitting behavior were analyzed. The results of the microstructural characterization and stress analyses were then correlated with axial-splitting behavior of high-burnup PWR cladding reported for simulated-RIA conditions. The effects of key test procedures and their implications for the interpretation of RIA test results are discussed

TMI-2 Vessel Investigation Project (VIP) Metallurgical Program

International Nuclear Information System (INIS)

Diercks, D.R.; Neimark, L.A.

1991-01-01

The Three Mile Island Unite 2 (TMI-2) Vessel Investigation Project Metallurgical Program is a part of the international TMI-2 Vessel Investigation Project being conducted jointly by the U.S. Nuclear Regulatory Commission and the Organization for Economic Cooperation and Development. The objectives of the metallurgical program are to deduce the temperatures of, determine the mechanical properties of, and assess the integrity of the TMI-2 lower head during the loss-of-coolant accident. Fifteen samples have been removed from the lower head and are being examined. In addition, archive material from the lower head of the Midland nuclear reactor has been procured for conducting supplemental metallurgical evaluations and mechanical property determinations. Evaluations of the microstructure and mechanical properties of the as-received archive material have been completed, and a series of heat treatment experiments has been conducted to develop standard microstructures to be compared with those present in the TMI-2 samples. Results have been obtained from examinations of two of the fifteen TMI-2 lower head samples. These results indicate that one of these two samples, which contained cracks in the weld cladding extending ∼3 mm into the underlying base metal, apparently reached temperatures on the order of 1000 to 1100C during the accident. A preliminary examination of the core debris deposited on this sample has been performed. The other sample, from an area away from the region of core relocation, did not exceed 727C during the accident

Metallurgical applications: fractography

International Nuclear Information System (INIS)

Meny, L.

1978-01-01

The principal metallurgical uses of the scanning electron microscope and the microprobe described here employ images obtained on a CRT from an electron signal or X rays. The various electron signals are the back scattered electrons, secondary electrons and absorbed electrons. The differences in the intensity of thee signals with the acceleration tension E 0 , the inclination angle β, the atomic number Z of the target and any potential applied to the sample give rise to contrasts: atomic number contrast, given by the sample current or the back scattered electrons; topographical contrast, given by the emission of the secondary electrons Δ that vary with α (the angle between the normal to the surface and the direction of the incident beam) [fr

Fuel for domestic and metallurgical uses

Energy Technology Data Exchange (ETDEWEB)

Basu, D.; Chakrabarti, R.K.

1981-02-01

To meet the energy requirements in the domestic and metallurgical sectors CMPDI have taken in hand some developmental projects using coal as a feedback. 4 projects are described - mechanized conversion of coal to domestic coke, formed coke making by Didier-Keihan-Sumitomo process, domestic briquette making based on non-copking coal resources, and smokeless coal blocks utilising inferior grade raw coal and washery by-products.

Development of market strategies of metallurgical enterrprises after restructuring of steel industry

Directory of Open Access Journals (Sweden)

B. Gajdzik

2014-01-01

Full Text Available Before metallurgical enterprises started implementation of marketing activities they had to go through restructuring processes which included all areas of their market activities. Privatised metallurgical enterprises after economic transformation gradually implemented marketing to their business activities. The article presents notions connected with development of marketing strategies from the period of last 20 years. The range of analysis includes categories corresponding with instruments of mix marketing (4P − product, price, place, promotion.

Effect of compression deformation on the microstructure and corrosion behavior of magnesium alloys

International Nuclear Information System (INIS)

Snir, Y.; Ben-Hamu, G.; Eliezer, D.; Abramov, E.

2012-01-01

Highlights: ► Metallurgical features (mainly twinning, dislocation accumulation, and dynamic recrystallization). ► The thermo-mechanical state (amount of deformation and its temperature). ► The corrosion behavior of wrought Mg-alloys. This correlation was emphasized by the mechanical behavior measured through micro-hardness. ► Microstructural changes during deformation, and potentio-dynamic corrosion tests were correlated. - Abstract: The effect of deformation on the corrosion and mechanical behavior of wrought Mg-alloys AZ31, AM50, and ZK60 was investigated. The materials’ behavior was correlated to the changes in metallurgical features, during compression, into different amounts of deformation at three temperatures: 250° C, 280° C, and 350° C. The metallurgical features were monitored by optical microscope, scanning electron microscope (SEM), and transmission electron microscopy (TEM). It was observed that there is a very strong correlation between three features: 1. metallurgical features (mainly twinning, dislocation accumulation, and dynamic recrystallization); 2. The thermo-mechanical state (amount of deformation and its temperature); and 3. The corrosion behavior of wrought Mg-alloys. This correlation was emphasized by the mechanical behavior measured through micro-hardness. Microstructural changes during deformation, and potentio-dynamic corrosion tests were correlated. These results show that studies on the effect of thermo-mechanical state (related to the microstructure) on the corrosion behavior of wrought Mg-alloys are essential in order to optimize their applicability to plastic forming processes.

Utilization of secondary energy resources of metallurgical ...

African Journals Online (AJOL)

... with a heat output of 4200 kW, a working agent R 600, a source of low-potential heat-circulating water: a 460 kW gas engine. The proposed scheme showed high efficiency of power supply of the town in comparison with the gas boiler. Keywords: heat pump; internal combustion engine metallurgical plant; energy efficiency ...

Safety performance indicators in the metallurgical industry using WEB programming

Directory of Open Access Journals (Sweden)

M. Cioca

2017-01-01

Full Text Available Sustainable development has a significant impact today in Romania and worldwide. In this context, risk assessment becomes mandatory for enterprises. This paper analyzes the situation of occupational risks in the metallurgical industry in the European Union, Romania, and the United States and highlights the main causes for work accidents in Romanian metallurgical industry. The analysis covers the period 2010 - 2016. The data collected from Romania is compared to the data related to the European Union and the United States. Moreover, the paper aims to present an occupational risk assessment tool, which is customizable for each area of activity. The last section of the paper discusses the research results and limitations.

The impact of production capacity utilization on metallurgical companies financing

Directory of Open Access Journals (Sweden)

J. Kutáč

2013-01-01

Full Text Available The most important and the most problematic in-house sources of financing of metallurgical companies are profit and depreciations. In the event that the aggregate value of the economic result and depreciations goes over to negative values, then this kind of in-house financing ceases to increase Cash Flow of the company but, on the contrary, it will cause its reduction. It means that this type of financing is to some extent uncertain, particularly in times of crisis, when there are noticeable fluctuations in sales volumes, leading to a significant influence of the volume of production on the amount of profit. The article discusses the impact of production capacity utilization on metallurgical companies financing.

Comparison of Metallurgical and Ultrasonic Inspections of Galvanized Steel Resistance Spot Welds

International Nuclear Information System (INIS)

Potter, Timothy J.; Ghaffari, Bita; Mozurkewich, George; Reverdy, Frederic; Hopkins, Deborah

2006-01-01

Metallurgical examination of galvanized steel resistance spot welds was used to gauge the capabilities of two ultrasonic, non-destructive, scanning techniques. One method utilized the amplitude of the echo from the weld faying surface, while the other used the spectral content of the echo train to map the fused area. The specimens were subsequently sectioned and etched, to distinguish the fused, zinc-brazed, and non-fused areas. The spectral maps better matched the metallurgical maps, while the interface-amplitude method consistently overestimated the weld size

Retail optimization in Romanian metallurgical industry by applying of fuzzy networks concept

Directory of Open Access Journals (Sweden)

Ioana Adrian

2017-01-01

Full Text Available Our article presents possibilities of applying the concept Fuzzy Networks for an efficient metallurgical industry in Romania. We also present and analyze Fuzzy Networks complementary concepts, such as Expert Systems (ES, Enterprise Resource Planning (ERP, Analytics and Intelligent Strategies (SAI. The main results of our article are based on a case study of the possibilities of applying these concepts in metallurgy through Fuzzy Networks. Also, it is presented a case study on the application of the FUZZY concept on the Romanian metallurgical industry.

A new evolutionary system for evolving artificial neural networks.

Science.gov (United States)

Yao, X; Liu, Y

1997-01-01

This paper presents a new evolutionary system, i.e., EPNet, for evolving artificial neural networks (ANNs). The evolutionary algorithm used in EPNet is based on Fogel's evolutionary programming (EP). Unlike most previous studies on evolving ANN's, this paper puts its emphasis on evolving ANN's behaviors. Five mutation operators proposed in EPNet reflect such an emphasis on evolving behaviors. Close behavioral links between parents and their offspring are maintained by various mutations, such as partial training and node splitting. EPNet evolves ANN's architectures and connection weights (including biases) simultaneously in order to reduce the noise in fitness evaluation. The parsimony of evolved ANN's is encouraged by preferring node/connection deletion to addition. EPNet has been tested on a number of benchmark problems in machine learning and ANNs, such as the parity problem, the medical diagnosis problems, the Australian credit card assessment problem, and the Mackey-Glass time series prediction problem. The experimental results show that EPNet can produce very compact ANNs with good generalization ability in comparison with other algorithms.

Modern recycling methods in metallurgical industry

Directory of Open Access Journals (Sweden)

M. Maj

2010-04-01

Full Text Available The contamination of environment caused by increased industrial activities is the main topic of discussions in Poland and in the world. The possibilities of waste recovery and recycling vary in different sectors of the industry, and the specific methods, developed and improved all the time, depend on the type of the waste. In this study, the attention has been focussed mainly on the waste from metallurgical industry and on the available techniques of its recycling

The beryllium production at Ulba metallurgical plant (Ust-Kamenogrsk, Kazakhstan)

Energy Technology Data Exchange (ETDEWEB)

Dvinskykh, E.M.; Savchuk, V.V.; Tuzov, Y.V. [Ulba Metallurgical Plant (Zavod), Ust-Kamenogorsk, Abay prospect 102 (Kazakhstan)

1998-01-01

The Report includes data on beryllium production of Ulba metallurgical plant, located in Ust-Kamenogorsk (Kazakhstan). Beryllium production is showed to have extended technological opportunities in manufacturing semi-products (beryllium ingots, master alloys, metallic beryllium powders, beryllium oxide) and in production of structural beryllium and its parts. Ulba metallurgical plant owns a unique technology of beryllium vacuum distillation, which allows to produce reactor grades of beryllium with a low content of metallic impurities. At present Ulba plant does not depend on raw materials suppliers. The quantity of stored raw materials and semi-products will allow to provide a 25-years work of beryllium production at a full capacity. The plant has a satisfactory experience in solving ecological problems, which could be useful in ITER program. (author)

Conceptual design for treatment of mining and metallurgical wastewaters which contains arsenic and antimony

Directory of Open Access Journals (Sweden)

Željko Kamberović

2012-12-01

Full Text Available This paper presents a preliminary design for treatment of mining and metallurgical wastewaters (MMW from the basin of antimony “Zajača“, which contains high concentrations of arsenic and antimony. MMW have been investigated in laboratory, due to large difference in concentrations of pollutants. Metallurgical wastewaters were treated using iron (II-sulfate and lime milk used to adjust the pH value at 7. After chemical treatment of metallurgical wastewater and its joining with mining wastewater, residual amount of arsenic in water was below maximum allowed concentrations, while the concentration of antimony, remained above the maximum allowed value. The final phase of purification process was performed using ion exchange resin. After treatment of MMW, they can be used as technical water in the smelting process of secondary raw lead materials.

Microwave-assisted grinding of metallurgical coke; Molienda asistida con microondas de un coque metalurgico

Energy Technology Data Exchange (ETDEWEB)

Ruisanchez, E.; Juarez-Perez, E. J.; Arenillas, A.; Bermudez, J. M.; Menendez, J. A.

2014-10-01

Metallurgical cokes are composed of graphitic carbon (s2p2) and different inorganic compounds with very different capacities to absorb microwave radiation. Moreover, due to the electric conductivity shown by the metallurgical cokes, microwave radiation produces electric arcs or microplasmas, which gives rise to hot spots. Therefore, when these cokes are irradiated with microwaves some parts of the particle experiment a rapid heating, while some others do not heat at all. As a result of the different expansion and stress caused by thermal the shock, small cracks and micro-fissures are produced in the particle. The weakening of the coke particles, and therefore an improvement of its grind ability, is produced. This paper studies the microwave-assisted grinding of metallurgical coke and evaluates the grinding improvement and energy saving. (Author)

Au/Zn Contacts to rho-InP: Electrical and Metallurgical Characteristics and the Relationship Between Them

Science.gov (United States)

Weizer, Victor G.; Fatemi, Navid S.; Korenyi-Both, Andras L.

1994-01-01

The metallurgical and electrical behavior of Au/Zn contacting metallization on p-type InP was investigated as a function of the Zn content in the metallization. It was found that ohmic behavior can be achieved with Zn concentrations as small as 0.05 atomic percent Zn. For Zn concentrations between 0.1 and 36 at. percent, the contact resistivity rho(sub c) was found to be independent of the Zn content. For low Zn concentrations the realization of ohmic behavior was found to require the growth of the compound Au2P3 at the metal-InP interface. The magnitude of rho(sub c) is shown to be very sensitive to the growth rate of the interfacial Au2P3 layer. The possibility of exploiting this sensitivity to provide low resistance contacts while avoiding the semiconductor structural damage that is normally attendant to contact formation is discussed.

Proceedings of the 48. conference of metallurgists : international symposium on process control applications in mining and metallurgical plants

Energy Technology Data Exchange (ETDEWEB)

Shang, H. [Laurentian Univ., Sudbury, ON (Canada). School of Engineering; Ryan, L. [Barrick Gold Corp., Toronto, ON (Canada); Kennedy, S. [Barrick Gold Corp., Dar Es Salaam (Tanzania, United Republic of)] (eds.)

2009-07-01

This international symposium on process control applications in mining and metallurgical plants was held to promote economic and sustainable production practices in Canadian industry applications. Topics related to process control in mining and metallurgical plants included expert systems, model-based control technology, as well as recent advances in simulation, monitoring, and optimization techniques. Methods of improving the process and energy efficiency of mining and metallurgical plants were discussed along with technologies designed to improve monitoring accuracy. The symposium was divided into the following 5 sessions: (1) expert system, control, and performance monitoring, (2) flotation, (3) metallurgical processes, modelling, (4) mining applications, and (5) monitoring, analysis. The symposium featured 23 presentations, of which 2 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Autonomous and professional maintenance in metallurgical enterprise as activities within total productive maintenance

Directory of Open Access Journals (Sweden)

B. Gajdzik

2014-04-01

Full Text Available The content of this publication consists of notions connected with Total Productive Maintenance (TPM in metallurgical enterprise. The basic areas of devices condition management through Autonomous and Professional Maintenance are described here. Mentioned areas of activities are performed in metallurgical enterprise ArcelorMittal Poland within pillars of World Class Manufacturing (WCM. The aims of UR programs are to maintain the basic functionality of the devices and decrease the number of failures in order to reach improvement of production efficiency.

Mining-metallurgical projects for the production of uranium concentrates

International Nuclear Information System (INIS)

Ajuria-Garza, S.

1983-01-01

This report presents an overall view of a complete project for a mining-metallurgical complex for the production of uranium concentrates. Relevant aspects of each important topic are discussed as parts of an integrated methodology. The principal project activities are analyzed and the relationships among the various factors affecting the design are indicated. A list of 96 principal activities is proposed as an example. These activities are distributed in eight groups: initial evaluations preliminary feasibility studies, project engineering, construction, industrial operation, decommissioning and post-decommissioning activities. The environmental impact and the radiological risks due to the construction and operation of the mining metallurgical complex are analyzed. The principles of radiological protection and the regulations, standards and recommendations for radiological protection in uranium mines and mills are discussed. This report is also a guide to the specialized literature: a bibliography with 765 references is included. (author)

Residual life assessment of French PWR vessel head penetrations through metallurgical analysis

International Nuclear Information System (INIS)

Pichon, C.; Boudot, R.; Benhamou, C.; Gelpi, A.

1994-01-01

In September 1991, a vessel head penetration was found leaking at Bugey 3 plant during the hydrotest included in the framework of decennial In Service Inspections. Non destructive examinations performed afterwards on several other plants have shown some cracked penetrations. Destructive expertise confirmed quickly that again this new problem is related to stress corrosion cracking of Alloy 600 used as base material. During the last 15 years, similar cracking have been met in steam generator tubes and secondly in pressurizer instrumentation tubes. In spite of all the work performed since that time an extension appears to be necessary for explaining the features of this new event; however material sensitivity, stress and temperature still remain the key parameters governing the behavior of Alloy 600 in PWR environment. In this paper, only the material sensitivity of vessel head penetrations is examined through metallurgical analysis in relation with SCC tests. On the basis of vessel head field experience in combination with thermomechanical process used for fabrication of original bars criteria for a sensitivity ranking of penetrations are proposed. Metallurgical investigations and SCC tests were carried out to support this sensitivity ranking. The final aim is to use such information among those quoted above for assessment of vessel heads residual life. This document is an overview of the work performed in France concerning the material sensitivity of forged Alloy 600. It represents an important part of the assessments and investigations undertaken in France on the stress corrosion cracking phenomenon affecting the reactor vessel head penetrations in PWR's

Control and metallurgical examination on safety injection piping

International Nuclear Information System (INIS)

Thebault, Y.; Grandjean, Y.; Gauthier, V.; Lambert, B.; Debustcher, B.

1998-01-01

From 1992 until 1997, cracking phenomena by thermal fatigue regarding safety injection piping were evidenced on several PWR 900 MW reactors. These events led EDF to the implementation of a first maintenance programme. In December 1996, a new leak occurred on an EDF 900 MW PWR in operation and was located on a safety injection pipe. In site inspections and metallurgical examinations carried out in the EDF hot Laboratory evidenced defects inside the pipe, out of the welding areas. These degradations are the consequence of a fatigue cracking phenomenon with thermal cycling linked to permanent tensile stresses. Following this incident, a programme of non destructive testing was implemented on all the EDF 900 MW plants. These inspections exhibited the same defects on other PWR 900 MW units. The results of the metallurgical examinations and also in site inspection results allowed EDF to understand the phenomenon and to validate an inspection programme on the one hand and a modification of the design of the circuits on the other hand. (authors)

Efficiency of Polish metallurgical industry based on data envelopment analysis

Directory of Open Access Journals (Sweden)

J. Baran

2016-04-01

Full Text Available The main purpose of this paper is to compare the technical efficiency of 12 sectors manufacturing basic metals and metal products in Poland. This article presents the use of Data Envelopment Analysis models, to determine overall technical efficiency, pure technical efficiency and scale efficiency of metallurgical branches in Poland. The average technical efficiency of metallurgical industry in Poland was quite high. The analysis gives a possibility to create a ranking of sectors. Three branches were found to be fully efficient: manufacture of basic iron and steel and of ferroalloys, manufacture of basic precious and other non - ferrous metals and manufacture of tubes, pipes, hollow profiles and related fittings, of steel. The results point out the reasons of the inefficiency and provide improving directions for the inefficient sectors.

Economic statistics for the extractive and metallurgical industries for 1974/1975

Energy Technology Data Exchange (ETDEWEB)

Medaets, J

1977-11-01

Statistical data are presented for the extractive industries (coal, ore, quarries etc); coke and agglomerates manufacture; metallurgical industries; and the related hydrology. (In French and in Dutch)

Electric arc spraying for restoration and repair of metallurgical equipment parts

Directory of Open Access Journals (Sweden)

В’ячеслав Олександрович Роянов

2016-07-01

Full Text Available It has been shown that the electric arc spraying with the use of powder wires can be used to repair and restore parts of metallurgical equipment. The technology of spraying parts by means of the cored wire Steelcored M8TUV; T462MMIN5 and combinations of steel and aluminum wires to restore shaft-gears, shaft-beams, cranes axles for the foundry of the Moldavian Metallurgical Plant has been introduced. The composition of the flux-cored wires MMP-2,3 developed at the Department of Equipment and welding production technology of PSTU that provides the required hardness and adhesion of the coating and the substrate have been shown and the results of the coatings properties studies have been published. Studies have shown matching properties of the coatings to be used for details of the metallurgical equipment working under difficult conditions, including the rolls of rolling mills. Cored wire was used for pilot plating of the rolls surface of the skin-rolling stand at the cold-rolling mill at Illich Steel and Iron Works, Mariupol. Residual coating thickness ranged from 15 to 25 microns. Strip sized 0,9 × 1025 mm has been rolled, the squeezing is equal to 0,8...1,0%.

Proceedings of papers. 3. Balkan Metallurgical Conference

International Nuclear Information System (INIS)

Mickovski, Jovan

2003-01-01

This Conference aims to be a central event in the metallurgy research of Balkan, fulfilling the goals to present the most outstanding relevant developments in modern metallurgy; to inspire high standards of excellence in pure and applied metallurgy research; to attract outstanding scientists to present central lectures on modem metallurgical research, and on the challenges imposed by the needs of society; to inspire the young generation of metallurgists in Balkan and other countries. Following these lines, the 3. Balkan Conference on Metallurgy will provide a unique opportunity for academic and industrial metallurgists from the Balkan countries and wider, to exchange ideas, expertise, and experience on topics related to the theme of the Conference - Balkan Metallurgy in Search for New Ways of Development. The aim of the organizers was to bring together distinguished experts, not only to present their work, but also to discuss the major scientific and technological challenges facing metallurgy in this millennium.The 6 sections of the conference were entitled: Section A: Extractive metallurgy; Section B: Physical metallurgy and materials science - ferrous metals and non ferrous metals; Section C: Management, maintenance control and optimization of metallurgical processes; Section D: New technologies and techniques; Section E: Refractory and powder; Section F: Corrosion and protection of metals. Papers relevant to INIS are indexed separately

Effects of Vertex Activity and Self-organized Criticality Behavior on a Weighted Evolving Network

International Nuclear Information System (INIS)

Zhang Guiqing; Yang Qiuying; Chen Tianlun

2008-01-01

Effects of vertex activity have been analyzed on a weighted evolving network. The network is characterized by the probability distribution of vertex strength, each edge weight and evolution of the strength of vertices with different vertex activities. The model exhibits self-organized criticality behavior. The probability distribution of avalanche size for different network sizes is also shown. In addition, there is a power law relation between the size and the duration of an avalanche and the average of avalanche size has been studied for different vertex activities

Upgraded metallurgical-grade silicon solar cells with efficiency above 20%

Energy Technology Data Exchange (ETDEWEB)

Zheng, P.; Rougieux, F. E.; Samundsett, C.; Yang, Xinbo; Wan, Yimao; Macdonald, D. [Research School of Engineering, College of Engineering and Computer Science, The Australian National University, Canberra, Australian Capital Terrritory 2601 (Australia); Degoulange, J.; Einhaus, R. [Apollon Solar, 66 Cours Charlemagne, Lyon 69002 (France); Rivat, P. [FerroPem, 517 Avenue de la Boisse, Chambery Cedex 73025 (France)

2016-03-21

We present solar cells fabricated with n-type Czochralski–silicon wafers grown with strongly compensated 100% upgraded metallurgical-grade feedstock, with efficiencies above 20%. The cells have a passivated boron-diffused front surface, and a rear locally phosphorus-diffused structure fabricated using an etch-back process. The local heavy phosphorus diffusion on the rear helps to maintain a high bulk lifetime in the substrates via phosphorus gettering, whilst also reducing recombination under the rear-side metal contacts. The independently measured results yield a peak efficiency of 20.9% for the best upgraded metallurgical-grade silicon cell and 21.9% for a control device made with electronic-grade float-zone silicon. The presence of boron-oxygen related defects in the cells is also investigated, and we confirm that these defects can be partially deactivated permanently by annealing under illumination.

Post-failure metallurgical investigation of KNK steam generator tube damage

Energy Technology Data Exchange (ETDEWEB)

Lorenz, H; Herberg, G

1975-07-01

In September 1973 the sodium-cooled reactor KNK was shut down due to a steam generator tube damage. Failure location and results of the metallurgical examination of the damage are described. The cause of the damage is discussed. (author)

IFM – SCIENTIFIC CENTRE OF THE DEVELOPMENT OF THE UKRAINIAN METALLURGICAL INDUSTRY

Directory of Open Access Journals (Sweden)

BOLSHAKOV V. I.

2017-01-01

Full Text Available The history of creation and development of the Institute of ferrous metallurgy of the Ukrainian Academy of Sciences named after Z. I. Nekrasov is regarded in the article. IFM has become the scientific centre of the development of the metallurgical industry of Ukraine. Researches of the outstanding scientists show their significant contribution in the development of the metallurgical science and implementation of their achievements in the production of the metallurgical industry of Ukraine. Analysis of publications. History of the Institute of the ferrous metallurgy is regarded in the fundamental works devoted to the development of the metallurgical industry in Ukraine and in the works published to the jubilee dates of the prominent scientists academicians Z. I. Nekrasov, V. I. Bol’shakov and others. The purpose of the article is to analyze the process of the creation of the Institute and the stages of its development in the 20th and 21st centuries and to define the influence of the economic and political situation in the country upon this process? To regard the role of the outstanding scientists and influence of their achievements on the development of the metallurgical industry of Ukraine. The history of IFM began in 1939 when it was organized in Kharkiv as a part of the Academy of Sciences of Ukraine. At the beginning of the Great Patriotic war the Institute was moved to Ufa – the capital of Bashkiria. During the war the scientists of the Institute tried to increase the output of metal and special steels for the defence industry. In 1943 the Institute moved to Moscow and then to Kiev. In 1952 it was decided to move the Institute to Dnepropetrovsk. In order to combine the scientific researches and production of metal. Z. I. Nekrasov was elected Director of the Institute. The departments of the Indtitute were headed by academicians Z. I. Nekrasov, A. P. Chekmariov, K. F. Starodubov, Correspondence Members of the Ukrainian Academy of Sciences

Qualifications versus useful knowledge in metallurgical enterprise

Directory of Open Access Journals (Sweden)

B. Gajdzik

2014-01-01

Full Text Available The article presents notions connected with resource structure of useful knowledge packages in metallurgical enterprise. Dependence between building competence of employees and using knowledge for the need of better efficiency of the enterprise was discussed here. ArcelorMittal Poland enterprise served as case study here due to the fact that it strives at World Class Management by putting emphasis on bringing areas of business activity to perfection through participation and involvement of employees.

The 6th European metallurgical conference EMC 2011: Proceedings review

Directory of Open Access Journals (Sweden)

Srećko R. Stopić

2011-10-01

Full Text Available The GDMB Society for Mining, Metallurgy, Resource and Environmental Technology organized the 6th European Metallurgical Conference (2011 in Duesseldorf from June 26 to 29, 2011. The same venue hosted the most important international metallurgical trade fairs for metallurgy of iron and steel, new casting and thermochemical processes METEC, GIFA, THERMOPROCESS and NEWCAST. The previous European metallurgical conferences were organized by GDMB in Friedrichshafen (2001, Hanover (2003, Leipzig (2005, Duesseldorf (2007, Innsbruck (2009. The GDMB is a non-profit organization situated in Clausthal in Germany, which is related to combining science with the practical experience in metallurgy, mining, materials engineering, mineral processing, recycling and refining of metals, and manufacturing of semi- and finishing products. The European Metallurgical conference EMC is one of the most known conferences worldwide in the field of non-ferrous metallurgy and is attended regularly by the decision makers from the industry and universities. The scientific program contained 6 plenary lectures and more than 160 presentations from 40 countries in 5 parallel series. An extensive poster exhibition was held, during which the authors had an opportunity to introduce their posters to the entire plenum as a part of a brief presentation. The best poster from the Montan-University in Leoben, Austria, was awarded the € 500 'Poster Award EMC 2011'. Not only were the most important European countries represented here, more than one third of the lecturers were from the non-European countries (Canada, Japan, China, USA, South Africa, Australia. The origin of the participants reflects the aim of the organizers: to make this conference a worldwide platform for the scientific exchange of experience and information. More than 400 participants from all over the world participated at this conference. The scientific presentations of the conference are presented in five Proceedings

Effects of mechanical activation on the carbothermal reduction of chromite with metallurgical coke

Directory of Open Access Journals (Sweden)

Kenan Yıldız

2010-06-01

Full Text Available The carbothermal reduction of mechanically activated chromite with metallurgical coke under an argon atmosphere was investigated at temperatures between 1100 and 1400°C and the effects of the mechanical activation on chromite structure were analyzed by x-ray diffraction (XRD and scanning electron microscopy (SEM. An increase in specific surface area resulted in more contact points. The activation procedure led to amorphization and structural disordering in chromite and accelerated the degree of reduction and metalization in the mixture of chromite and metallurgical coke. Carbothermal reduction products were analzed by using scanning electron microscopy (SEM/EDS.

Radioactivity of raw materials, metallurgical and casting products

International Nuclear Information System (INIS)

Hons, J.

2000-01-01

At present, the radioactive contamination of metallurgical products and initial materials represent a potential obstacle in foreign and domestic trade. It is of course an undesirable threat o the living environment on the one side and, at the same time, a new incorrectly used means for suppressing competition and forming a protection 'umbrella' of the national market to desirable imports on the other hand

Radiation protection aspects in the metallurgical examination of irradiated fuel elements

International Nuclear Information System (INIS)

Janardhanan, S.; Pillai, P.M.B.; Jacob, John; Kutty, K.N.; Wattamwar, S.B.; Mehta, S.K.

1981-01-01

The operational safety requirements of hot cell facilities for metallurgical examination of irradiated natural and enriched uranium fuel elements are highlighted. The cell shielding is designed for handling activities equivalent of 10 2 to 10 5 curies of gamma energy of 1.3 Mev. A brief outline of the built-in design features relevant to safety assessment is also incorporated. Reference is made to some salient features of Radiometallurgy Cells at Trombay. Metallurgical operations include investigations on cladding failure of irradiated material structure and specimen preparation from hot fuel element. The radiation protection aspects presented in this paper show that handling low irradiated fuel elements in these beta-gamma cells do not cause serious operational safety problems. The procedures followed and the containment provided would adequately restrict exposure of operational staff to acceptable limits. (author)

Methodological Approaches to Ensuring Innovative Development of Metallurgical Enterprises on the Basis of Principles of Economic Nationalism

Directory of Open Access Journals (Sweden)

Denysov Kostyantyn V.

2017-01-01

Full Text Available The economic, energy and environmental aspects of the activities of metallurgical enterprises are analyzed in the context of the need to ensure their sustainable development. The high energy intensity of the production process, the low efficiency and irrational structure of capital expenditures for environmental protection, the dominance of material costs in the final cost of finished products at the expense of labor and social contributions are indicated. There proved the low effectiveness of the previous measures of the industrial policy of the metallurgical industry innovative development that were not in compliance with the requirements of the WTO and led to taking compensatory measures against the Ukrainian steel on world markets. The potential of economic nationalism as a system for ensuring the innovative development of the metallurgical industry is considered. There determined the priorities of the industrial policy for the development of metallurgical enterprises based on the principles of economic nationalism and taking into account the global trends in the development of trade and economic relations and Ukraine’s commitments to the WTO.

The R85m President Brand joint metallurgical complex

International Nuclear Information System (INIS)

Payne, Adam.

1977-01-01

The uranium plant at President Brand, which was built in 1971 and opened last year, is now being extended. The plant forms only part of the extensive joint metallurgical complex being developed by Anglo American Corp. in the Free State, costing a total R85million. This article examines technical details of the recovery processes involved

Radiation protection aspects in the metallurgical examination of irradiated fuel elements

Energy Technology Data Exchange (ETDEWEB)

Janardhanan, S.; Pillai, P.M.B.; Jacob, J.; Kutty, K.N.; Wattamwar, S.B.; Mehta, S.K. (Bhabha Atomic Research Centre, Bombay (India). Health Physics Div.)

The operational safety requirements of hot cell facilities for metallurgical examination of irradiated natural and enriched uranium fuel elements are highlighted. The cell shielding is designed for handling activities equivalent of 10/sup 2/ to 10/sup 5/ curies of gamma energy of 1.3 Mev. A brief outline of the built-in design features relevant to safety assessment is also incorporated. Reference is made to some salient features of Radiometallurgy Cells at Trombay. Metallurgical operations include investigations on cladding failure of irradiated material structure and specimen preparation from hot fuel element. The radiation protection aspects presented in this paper show that handling low irradiated fuel elements in these beta-gamma cells do not cause serious operational safety problems. The procedures followed and the containment provided would adequately restrict exposure of operational staff to acceptable limits.

Arsenic precipitation from metallurgical effluents

International Nuclear Information System (INIS)

Navarro, P.; Vargas, C.; Araya, E.; Martin, I.; Alguacil, F. J.

2004-01-01

In the mining-metallurgical companies different liquid effluents are produced, which can contain a series of dissolved elements that are considered dangerous from an environmental point of view. One of these elements is the arsenic, especially in the state of oxidation +5 that can be precipitated as calcium or iron arsenate. To fulfil the environmental requests it should have in solution a content of arsenic lower than 0,5 mg/l and the obtained solid product should be very stable under the condition in which it will be stored. this work looks for the best conditions of arsenic precipitation, until achieving contents in solution lower than such mentioned concentration. Also, the stability of the precipitates was studied. (Author) 7 refs

Analytical control in metallurgical processes

International Nuclear Information System (INIS)

Coedo, A.G.; Dorado, M.T.; Padilla, I.

1998-01-01

This paper illustrates the role of analysis in enabling metallurgical industry to meet quality demands. For example, for the steel industry the demands by the automotive, aerospace, power generation, tinplate packaging industries and issue of environment near steel plants. Although chemical analysis technology continues to advance, achieving improved speed, precision and accuracy at lower levels of detection, the competitiveness of manufacturing industry continues to drive property demands at least at the same rate. Narrower specification ranges, lower levels of residual elements and economic pressures prescribe faster process routes, all of which lead to increased demands on the analytical function. These damands are illustrated by examples from several market sectors in which customer issues are considered together with ther analytical implications. (Author) 5 refs

Analytical ultrasonics for characterization of metallurgical microstructures and transformations

Science.gov (United States)

Rosen, M.

1986-01-01

The application of contact (piezoelectric) and noncontact (laser generation and detection) ultrasonic techniques for dynamic investigation of precipitation hardening processes in aluminum alloys, as well as crystallization and phase transformation in rapidly solidified amorphous and microcrystalline alloys is discussed. From the variations of the sound velocity and attenuation the precipitation mechanism and kinetics were determined. In addition, a correlation was established between the observed changes in the velocity and attenuation and the mechanical properties of age-hardenable aluminum alloys. The behavior of the elastic moduli, determined ultrasonically, were found to be sensitive to relaxation, crystallization and phase decomposition phenomena in rapidly solidified metallic glasses. Analytical ultrasonics enables determination of the activation energies and growth parameters of the reactions. Therefrom theoretical models can be constructed to explain the changes in mechanical and physical properties upon heat treatment of glassy alloys. The composition dependence of the elastic moduli in amorphous Cu-Zr alloys was found to be related to the glass transition temperature, and consequently to the glass forming ability of these alloys. Dynamic ultrasonic analysis was found to be feasible for on-line, real-time, monitoring of metallurgical processes.

Analytical study of getting clinker from metallurgical wastes

Directory of Open Access Journals (Sweden)

Володимир Петрович Кравченко

2016-07-01

Full Text Available The opportunities to get clinker (cement on the basis of 2-component mixtures of raw materials: waste slag + limestone (less than 10mm fraction unsuitable for sinter production and being a technological waste of preparing raw materials for steel production have been investigated. Chemical compositions of waste slag and limestone wastes were investigated in the central laboratory at the Illych plant. The waste slag was got at the «Ilyich» plant while waste limestone - less than 10 mm fraction - was got in the dumps of the mine group in Komsomolsk. Taking into account chemical composition fluctuations of the waste dump slags and limestone within a few percent, the optimal ratio of raw materials is 55-65% limestone waste, while it is 35-45% waste slag. The clinker quality is evaluated by its hydraulic module, which is equal to: m = 2,37 and is determined on the basis of the chemical composition of the 2-component raw material mixture. For this method of clinker production, the value of the hydraulic module is rather high; and the possibility of obtaining high-quality clinker of metallurgical wastes has been confirmed. The offered method for producing clinker makes it possible to utilize metallurgical wastes and to get substantial ecological and economic benefits

REM Sleep Behavior Disorder: Updated Review of the Core Features, the RBD-Neurodegenerative Disease Association, Evolving Concepts, Controversies, and Future Directions

Science.gov (United States)

Boeve, Bradley F.

2010-01-01

Rapid eye movement (REM) sleep behavior disorder (RBD) is a parasomnia manifested by vivid, often frightening dreams associated with simple or complex motor behavior during REM sleep. Patients appear to “act out their dreams,” in which the exhibited behaviors mirror the content of the dreams, and the dream content often involves a chasing or attacking theme. The polysomnographic features of RBD include increased electromyographic tone +/- dream enactment behavior during REM sleep. Management with counseling and pharmacologic measures is usually straight-forward and effective. In this review, the terminology, clinical and polysomnographic features, demographic and epidemiologic features, diagnostic criteria, differential diagnosis, and management strategies are discussed. Recent data on the suspected pathophysiologic mechanisms of RBD are also reviewed. The literature and our institutional experience on RBD are next discussed, with an emphasis on the RBD-neurodegenerative disease association and particularly the RBD-synucleinopathy association. Several issues relating to evolving concepts, controversies, and future directions are then reviewed, with an emphasis on idiopathic RBD representing an early feature of a neurodegenerative disease and particularly an evolving synucleinopathy. Planning for future therapies that impact patients with idiopathic RBD is reviewed in detail. PMID:20146689

Thermo-ecological cost (TEC evaluation of metallurgical processes

Directory of Open Access Journals (Sweden)

W. Stanek

2015-01-01

Full Text Available Metallurgy represents a complex production system of fuel and mineral non-renewable resources transformation. The effectiveness of resource management in metallurgical chains depends on the applied ore grade and on the irreversibility of components of the system. TEC can be applied to measure the influence of metallurgy on the depletion of natural resources. The paper discusses the possibility of application of TEC in metallurgy and presents illustrative example concerning blast-furnace process.

Control of innovation activity in a competitive metallurgical business

Science.gov (United States)

Bogdanov, S. V.

2010-12-01

Certain competitive advantages of a manufacturer on a goods market can be provided if one creates conditions for bifurcation development of an innovation process in metallurgical business under conditions of market uncertainty of a demand for goods of a specified consumer quality and determines the technical-and-economic versions of stable operation of a production system for performing orders of metal product consumers.

Cost estimation and management over the life cycle of metallurgical ...

African Journals Online (AJOL)

This study investigates whether all expected costs over the life cycle of metallurgical research projects are included in initial, normal and fi nal cost estimates, and whether these costs are managed throughout a project's life cycle since there is not enough emphasis on the accurate estimation of costs and their management ...

Highlights of the metallurgical behaviour of CANDU pressure tubes

International Nuclear Information System (INIS)

Price, E.G.

1984-10-01

This paper is an overview of the service induced metallurgical changes that take place in Zircaloy-2 and Zr-2.5 wt. percent Nb pressure tubes in CANDU reactors. It incorporates the findings of an evaluation program, that followed a significant pressure tube failure at Ontario Hydro's Pickering Nuclear Generating Station, and also provides valid reasons for continued confidence in the current CANDU design

Simulation model for planning metallurgical treatment of large-size billets

International Nuclear Information System (INIS)

Timofeev, M.A.; Echeistova, L.A.; Kuznetsov, V.G.; Semakin, S.V.; Krivonogov, A.B.

1989-01-01

The computerized simulation system ''Ritm'' for planning metallurgical treatment of billets is developed. Three principles, specifying the organization structure of the treatment cycle are formulated as follows: a cycling principle, a priority principle and a principle of group treatment. The ''Ritm'' software consists of three independent operating systems: preparation of source data, simulation, data output

Real time information management for improving productivity in metallurgical complexes

International Nuclear Information System (INIS)

Bascur, O.A.; Kennedy, J.P.

1999-01-01

Applying the latest information technologies in industrial plants has become a serious challenge to management and technical teams. The availability of real time and historical operations information to identify the most critical part of the processing system from mechanical integrity is a must for global plant optimization. Expanded use of plant information on the desktop is a standard tool for revenue improvement, cost reduction, and adherence to production constraints. The industrial component desktop supports access to information for process troubleshooting, continuous improvement and innovation by plant and staff personnel. Collaboration between groups enables the implementation of an overall process effectiveness index based on losses due to equipment availability, production and product quality. The key to designing technology is to use the Internet based technologies created by Microsoft for its marketplace-office automation and the Web. Time derived variables are used for process analysis, troubleshooting and performance assessment. Connectivity between metallurgical complexes, research centers and their business system has become a reality. Two case studies of large integrated mining/metallurgical complexes are highlighted. (author)

LWR surveillance dosimetry improvement program: PSF metallurgical blind test results

International Nuclear Information System (INIS)

Kam, F.B.K.; Stallmann, F.W.; Guthrie, G.; McElroy, W.N.

1985-01-01

The ORR-PSF benchmark experiment was designed to simulate the surveillance capsule-pressure vessel configuration in power reactors and to test the validity of procedures which determine the radiation damage in the vessel from test results in the surveillance capsule. The PSF metallurgical blind test was initiated to give participants an opportunity to test their current embrittlement prediction methodologies. Experimental results were withheld from the participants except for the type of information which is normally contained in surveillance reports. Preliminary analysis of the PSF metallurgical blind test results shows that: (1) current prediction methodologies, as used by the PSF Blind Test participants, are adequate, falling within +- 20 0 C of the measured values for Δ NDT. None of the different methods is clearly superior; (2) the proposed revision of Reg. Guide 1.99 (Rev. 2) gives a better representation of the fluence and chemistry dependency of Δ NDT than the current version (Rev. 1); and (3) fluence rate effects can be seen but not quantified. Fluence spectral effects are too small to be detectable in this experiment. (orig.)

Continuous moisture measurement in metallurgical coke with automatic charge correction

International Nuclear Information System (INIS)

Watzke, H.; Mehlhose, D.

1981-01-01

A process control system has been developed for automatic batching of the coke amount necessary for metallurgical processes taking into account the moisture content. The measurement is performed with a neutron moisture gage consisting of an Am-Be neutron source and a BF 3 counter. The output information of the counter is used for computer-controlled batching

Production capacity of metallurgical enterprises in modular structure of management accounting

Directory of Open Access Journals (Sweden)

Zambrzhitskaia E.S.

2017-01-01

Full Text Available This article is the result of constant research in development of management accounting at modern Russian metallurgical works. The required steps of renovation are presented for the modernization of management accounting system in the case of production capacity. The necessary factors with defined values are systematized for modern enterprises. The main ones are those which are regulate the measure of the payload of production capacity. For the purposes of effective management accounting at metallurgical enterprises it is suggested to use the system of controlling parameters which were formulated for the enterprise for production of rolls. Later in the article the necessary changes to the modular structure of management accounting business are described and expanded with new structural element – “Management of production capacity”. The suggested methodical approach will allow the company management to respond quickly to rapidly changing external environment and, as a consequence, to make effective management decisions.

Application of logistic principles in metallurgical production

Directory of Open Access Journals (Sweden)

D. Malindžák

2012-07-01

Full Text Available Metallurgical production processes (MPP consist of continuous and discrete types of technology operation, transport, manipulation and storing processes regards the flow of material and also the equipment and machines. Other specifics are: long production cycles, great inertia, tree structure of production processes (from roots up to the leaves, high level of investments etc. These characteristics resulted in some specifics of production logistics. This article deals with these specifics and explains it using the conditions of production processes of continuous slab casting, their heating in push furnaces at rolling temperature and rolling itself in hot wideband steel mill.

Quality of some Nigerian coals as a blending stock in metallurgical ...

African Journals Online (AJOL)

Lafia- Obi/foreign coals blends possess lower ash and better rheological properties compared to Chikila/foreign coal composites which have high ash and poor rheological properties. These together suggest that amongst the two Nigerian coals, Lafia-Obi is superior for blending with the foreign ones in metallurgical coke ...

Child abuse and the balance of power in parental relationships: an evolved domain-independent mental mechanism that accounts for behavioral variation.

Science.gov (United States)

Handwerker, W P

2001-01-01

Previous studies use zero-order analyses to show a link between child abuse and exposure to "stepfathers." These studies rest on a proposed evolved, domain-specific cognitive mechanism that induces adult males to abuse or kill offspring not their own and, so, contribute directly to reproductive success. However, child abuse may reflect an evolved neurological mechanism that creates behavioral plasticity and adaptability by assigning emotional weights (which in consciousness appear rationalized as costs and benefits) to choice alternatives in all behavioral domains. This mechanism should act as a selective mechanism to create enhanced ability to avoid predation (social exploitation) and to obtain access to resources, given the properties of specific ecosystems, and should control behavioral responses to variation in the balance of power in social relationships. Power equalities should elicit good treatment for both parties; power inequalities, by contrast, should elicit exploitative and coercive behavior on the part of those who hold the balance of power. This paper reports a test of both hypotheses simultaneously, controlling for a standard social science risk factor (growing up in poverty). Once we control for the balance of power in parental relationships, exposure to a stepfather and growing up in poverty show no effect on the intensity of child abuse. Powerful women negotiated affectionate behavior from their partners for both themselves and their children; powerless women's negotiations with partners usually left both themselves and their children open to violence.

Process for converting coal into liquid fuel and metallurgical coke

Science.gov (United States)

Wolfe, Richard A.; Im, Chang J.; Wright, Robert E.

1994-01-01

A method of recovering coal liquids and producing metallurgical coke utilizes low ash, low sulfur coal as a parent for a coal char formed by pyrolysis with a volatile content of less than 8%. The char is briquetted and heated in an inert gas over a prescribed heat history to yield a high strength briquette with less than 2% volatile content.

Centralised process control of the metallurgical operation at Roessing, South West Africa/Namibia

International Nuclear Information System (INIS)

Thomas, R.; Erlank, B.

1987-01-01

A Honeywell TDC 2000 central process control system was installed at Roessing in 1984. The system controls the metallurgical operations from crushing to the finished product of uranium oxide and manufacture of sulphuric acid. The operation was previously controlled from nine separate local control rooms. The paper briefly reviews the design and commissioning of the control system on an operating plant and discusses the impact on manpower organisation and training needs. Development of the process control system during its first two years of operation is reviewed and a summary is given of the current status of computer control at Roessing. The impact of the new system on overall plant operation and performance efficiency is also briefly described. In conclusion, future developments of computer control and overall optimisation of metallurgical operations are reviewed

Metallurgical joining of engine parts. Inertia welding of nickel superalloy HP compressor disks

International Nuclear Information System (INIS)

Ferte, J.P.

1993-01-01

The main part of this paper describes upside metallurgical and mechanical work done at SNECMA, on inertia welding of powder metallurgy nickel base superalloys ASTROLOY and N18, allowing appliance of this process to engine parts : Inertia welding of superalloys leads to deap microstructural changes in the H.A.Z. which have been, as well as upset, correlated to process parameters, weld geometry and base material microstructure; a full mechanical testing of welds shown properties equivalent to base material ones up to 650 C except for fatigue crack growth behavior under specific conditions (T>600 C-hold time at maximum load) which is drastically reduced for in weld plane propagation. A significant improvement of this later property has been done through post-welding heat treatment and optimization of welding parameters. Last part of this paper summarize the main teachings gained, on the complete welding procedure, from welding of scale one parts. (orig.)

A thermo-metallurgical constitutive law of steels for structural mechanics

International Nuclear Information System (INIS)

Waeckel, Francois

1994-01-01

The aim of this work is to include the metallurgical behaviour of steels (and specifically their phases transformations) into thermo-mechanical studies. For this, a new model of aniso-thermal phase transformations during the cooling stage is proposed. Developed in the thermodynamics framework of simple materials with memory variables, its originality lies in the choice of the temperature time derivative T as independent variable. The identification and the transformation rates computation use the C.C.T. diagrams which are considered as families of particular solutions of evolution equations. The validation shows ability of the model to simulate all C.C.T. deductible tests. Furthermore, for some tests not included into the C.C.T., the numerical results remain good and the model, from which evolution equation form has been let free, allows to incorporate them to the identification data without modifying the C.C.T. simulation accuracy. Lastly, to take into account structural transformations mechanical effects, some currently used models have been introduced, together with the metallurgical model, in a finite element code. They allow whole quenching or welding simulations (up to residual stresses) as demonstrated by application examples. (author) [fr

Metallurgical behavior of fine fractions of copper sulfide minerals in a combined process of modified flotation and agitated bio leaching; Respuesta metalurgica de fracciones finas de minerales sulfurados de cobre en un proceso combinado de flotacion modificada y biolixiviacion agitada

Energy Technology Data Exchange (ETDEWEB)

Ibanez, J. P.; Ipinza, J.; Collao, N.; Ahlborn, G.

2007-07-01

The metallurgical behaviour of fine fraction of copper sulfide minerals of Compania Minera Quebrada Blanca S. A. was studied by concentration through flotation in aqueous media modified by alcohol followed by bio leaching of the concentrates. By using a 1% v/v of methanol, the metallurgical recovery of copper reaches 88%, while the iron recovery was 43%, the weight recovery was 18%, which indicates a high selectivity. these concentrates were then bio leached with and without nutrient medium, reaching 80% of copper recovery after 10 and 17 days, respectively. then, it is possible to conclude that this concentration-bio leaching metallurgical process is a promising route for copper recovery from the fine fraction of sulfide minerals. (Author) 24 refs.

Magnetic spherules from the soils near the slag dump of the Nizhniy Tagil metallurgical plant

Directory of Open Access Journals (Sweden)

A. B. Makarov

2017-12-01

Full Text Available Magnetic spherules, which are widespread in soils, can have different origins, but spherules with cosmic origin are the most studied. At that, functioning of numerous industrial enterprises of metallurgical profile, thermal power stations, and motor transport can be their origin. According to the data of previous researchers, spherical magnetic particles in soils can serve as an indicator for quantitative assessment of erosion-accumulative phenomena. The authors studied magnetic spherules, isolated from soil samples taken near the dump of blast furnace and metallurgical slags of a large Nizhny Tagil metallurgical plant located on the left bank of the Olkhovka river, functioning since 1949. The way the dump forms is by draining slag along the slope. Consequently, adjacent territories are exposed to a significant dust load, associated with increased concentrations of a number of heavy metals: chromium, iron, manganese, vanadium, copper and zinc. The study of magnetic spherules performed for samples of soils taken at a distance of 50 and 100 m to the west of the dump showed that the content of magnetic fraction in them was 15.1 and 11.7% respectively, of the mineral part of the samples. The authors studied magnetic spherules on a scanning microscope JEOL JSM 6390LV, an at that provide their morphology and the chemical composition of magnetic spherules (18 analyzes and aggregates on their surface (5 analyzes. Based on the presence of characteristic impurity elements, there are the following varieties: zinc, manganese, vanadium, determined by the peculiarities of metallurgical processes. Low concentrations of spherules in soils do not allow considering them as a significant source of pollution of natural environment, only a slight increase in the content of heavy metals characteristic for them is possible.

QEM*SEM: a necessary tool in the metallurgical evaluation of ore bodies

International Nuclear Information System (INIS)

Creelman, R.A.; Gottlieb, P.; Sutherland, D.; Jackson, R.

1989-01-01

The QEM*SEM system for automated image analysis of mineral samples is described. Details of the equipment are given together with information on the methods of measurement. Finally some practical applications are described where QEM*SEM has been used for the solution of metallurgical problems. 14 refs., 1 fig

SECI model and facilitation in change management in metallurgical enterprise

Directory of Open Access Journals (Sweden)

K. Grzybowska

2013-04-01

Full Text Available Organisational change management is not efficient without gaining and sharing knowledge by the members of the enterprise. Both in the conditions of relative organisational stability and in organisational chaos resulting from dynamic introduction and management of changes there is a constant need of improvement and of shaping competences and distribution of knowledge in the enterprise. The publication presents key programs of building knowledge conducted in a metallurgical enterprise.

Effect of metallurgical variables on void swelling

International Nuclear Information System (INIS)

Johnston, W.G.; Lauritzen, T.; Rosolowski, J.H.; Turkalo, A.M.

1976-01-01

The mechanism of void swelling is reviewed briefly and the anticipated effects of metallurgical variables are described. Experimental results showing the effects of metallurgical variables are reviewed, most of the work being done by simulation methods employing charged particle bombardments to simulate reactor damage. Although the early emphasis was on structural variables such as grain size, cold work and precipitates to control swelling, it now seems that the practical reduction of swelling will be achieved by modifying alloy composition. Void swelling is strongly influenced by the relative amounts of Fe, Cr, and Ni in an alloy; the amount of swelling can be varied by three orders of magnitude by changing the relative amounts of the three elements in an austenitic ternary alloy. The effect of composition on swelling of a simple ferritic alloy will also be described. The swelling of a simple austenitic alloy of Fe, Cr, and Ni can be reduced by certain minor element additions. The most effective swelling inhibitors are Si, Ti, Zr, and Nb, and combinations of Si and Ti are synergetic. Swelling reductions of two orders of magnitude have been achieved with combined additions. Predictions of swelling in commercial solid solution alloys are made on the basis of the present knowledge of the effects of major composition and minor element additions. The predictions agree with experimental results. For more complex commercial alloys, predictions are made for the effects on swelling of heat treatments that cause changes in matrix composition. In some cases, heat treatment is expected to change the peak swelling by more than a factor of ten, and to shift the peak swelling temperature by almost 100 0 C. Sensitivity of swelling to detailed matrix composition places emphasis on the need for developing understanding of the stability of structure and local composition in an irradiation environment

Test and Analysis of Metallurgical Converter Equipment

Directory of Open Access Journals (Sweden)

Shan Pang

2013-05-01

Full Text Available Oxygen top-blow converter is the main equipment in steel making, and its work reliability decides the security and economy of steel production. Therefore, how to design and test analysis of convertor has been an important subject of industry research. Geometric modelling and structure analysis of converter tilting device by using Pro/E program .The design Principle, basic design structure were analyzed in detail. The computer simulation software of metallurgical converter equipment and how to use it were introduced .It developed by VC++ software. The position of barycentre and moment curve in No.3 and No.4 are calculated. The converter acceleration down dip can be resolved by comparing the moment curve and center curve.

A comparison of the metallurgical behaviour of dispersion fuels with uranium silicides and U6Fe as dispersants

International Nuclear Information System (INIS)

Nazare, S.

1984-01-01

In the past few years metallurgical studies have been carried out to develop fuel dispersions with U-densities up to 7.0 Mg U m -3 . Uranium silicides have been considered to be the prime candidates as dispersants; U 6 Fe being a potential alternative on account of its higher U-density. The objective of this paper is to compare the metallurgical behaviour of these two material combinations with regard to the following aspects: (1) preparation of the compounds U 3 Si, U 3 Si 2 and U 6 Fe; (2) powder metallurgical processing to miniature fuel element plates; (3) reaction behaviour under equilibrium conditions in the relevant portions of the ternary U-Si-Al and U-Fe-Al systems; (4) dimensional stability of the fuel plates after prolonged thermal treatment; (5) thermochemical behaviour of fuel plates at temperatures near the melting point of the cladding. Based on this data, the possible advantages of each fuel combination are discussed. (author)

Project development for mining-metallurgical complexes for production of uranium concentrates - an analysis and a methodology

International Nuclear Information System (INIS)

Ajuria G, S.; Blanco P, B.; Pena A, J.; Manzanera Q, C.

1978-10-01

Activities comprising the development of a project for a mining-metallurgical complex for production of uranium concentrates, from sampling and evaluation of an orebody until plant start-up, are analyzed. The analysis of the orebody, characterization of the ore, bench scale and pilot plant metallurgical studies, environmental studies and economic analyses of the project are described. The mining project and mine preparation and engineering and construction of the plant are reviewed in less detail. The estimated time lapse for the development of a typical project under ideal conditions is 66 months. A bar diagram is included showing an approximate timetable for each activity. (author)

Studies on the influence of metallurgical variables on the stress corrosion behavior of AISI 304 stainless steel in sodium chloride solution using the fracture mechanics approach

International Nuclear Information System (INIS)

Khatak, H.S.; Gnanamoorthy, J.B.; Rodriguez, P.

1996-01-01

Stress corrosion data on a nuclear grade AISI type 304 stainless steel in a boiling solution of 5M NaCl + 0.15M Na 2 SO 4 + 3 mL/L HCl (bp 381 K) for various metallurgical conditions of the steel are presented in this article. The metallurgical conditions used are solution annealing, sensitization, 10 pct cold work, 20 pct cold work, solution annealing + sensitization, 10 pct cold work + sensitization, and 20 pct cold work + sensitization. The fracture mechanics approach has been used to obtain quantitative data on the stress corrosion crack growth rates. The stress intensity factor, K I , and J integral, J I , have been used as evaluation parameters. The crack growth rates have been measured using compact tension type samples under both increasing and decreasing stress intensity factors. A crack growth rate of 5 x 10 -11 m/s was chosen for the determination of threshold parameters. Results of the optical microscopic and fractographic examinations are presented. Acoustic signals were recorded during crack growth. Data generated from acoustic emissions, activation energy measurements, and fractographic features indicate hydrogen embrittlement as the possible mechanism of cracking

Correlation Between the Efficiency of Machinery and Equipment and the Productivity of Workers and its Effect on the Performance of a Metallurgical Undertaking

Directory of Open Access Journals (Sweden)

Kulawik, A.

2007-01-01

Full Text Available In this paper the example of procedure of life and objectify work effectiveness analysis in metallurgical enterprise were presented. Besides, on the example of chosen units of metallurgical enterprise, results of analysis - based on methodic proposed in the article - were discussed.

The Elementary Nature of Purposive Behavior: Evolving Minimal Neural Structures that Display Intrinsic Intentionality

Directory of Open Access Journals (Sweden)

John S. Watson

2005-01-01

Full Text Available A study of the evolution of agency in artificial life was designed to access the potential emergence of purposiveness and intentionality as these attributes of behavior have been defined in psychology and philosophy. The study involved Darwinian evolution of mobile neural nets (autonomous agents in terms of their adaptive weight patterning and structure (number of sensory, hidden, and memory units that controlled movement. An agent was embedded in a 10 × 10 toroidal matrix along with “containers” that held benefit or harm if entered. Sensory exposure to content of a container was only briefly available at a distance so that adaptive response to a nearby container required use of relevant memory. The best 20% of each generation of agents, based on net benefit consumed during limited lifetime, were selected to parent the following generation. Purposiveness emerged for all selected agents by 300 generations. By 4000 generations, 90% passed a test of purposive intentionality based on Piaget's criteria for Stage IV object permanence in human infants. An additional test of these agents confirmed that the behavior of 67% of them was consistent with the philosophical criterion of intention being “about” the container's contents. Given that the evolved neural structure of more than half of the successful agents had only 1 hidden and 1 memory node, it is argued that, contrary to common assumption, purposive and intentional aspects of adaptive behavior require an evolution of minimal complexity of supportive neural structure.

Comparative metallurgical study of thick hard coatings without cobalt

International Nuclear Information System (INIS)

Clemendot, F.; Van Duysen, J.C.; Champredonde, J.

1992-07-01

Wear and corrosion of stellite type hard coatings for valves of the PWR primary system raise important problems of contamination. Substitution of these alloys by cobalt-free hard coatings (Colmonoy 4 and 4.26, Cenium 36) should allow to reduce this contamination. A comparative study (chemical, mechanical, thermal, metallurgical), as well as a corrosion study of these coatings were carried out. The results of this characterization show that none of the studied products has globally characteristics as good as those of grade 6 Stellite currently in service

Metallurgical sessions. Second ALAMET congress (held in) Buenos Aires, Argentina, 6-10 May 1991

International Nuclear Information System (INIS)

1991-01-01

This congress was held in Buenos Aires, Argentine Republic, on May 6-10, 1991, gathering experts from all over the world. The present volume includes the papers presented at the Metallurgical Sessions - II. ALAMET Congress [es

Possibilities of Formation of Dioxins and Furans in Metallurgical Processes as well as Methods of their Reduction

Directory of Open Access Journals (Sweden)

Holtzer, M.

2007-01-01

Full Text Available The metallurgical industry, among others, generates various kinds of wastes: gaseous, dusts, wastes and sewage. Special attention of the European Union is directed towards the elimination or significant reduction of the gaseous-dust contamination emissions including the most hazardous compounds, such as dioxins and furans. In the article the sources of dioxins and furans in metallurgical industry are described along with the reduction methods of these pollutants. Particularly the activities recommended as the Best Available Techniques (BAT in order to reduce the PCDD/PCDF emission from sintering processes, non-ferrous metallurgy and foundry engineering have been presented.

Influence of the initial metallurgical state and the austenizing conditions on the distribution of austenitc grain size of the martensitic-ferritic steel T91(9%Cr-1%Mo-V-Nb)

International Nuclear Information System (INIS)

Zavaleta Gutierrez, N; Luppo, M.I; Danon, C.A; Garcia de Andres, C

2006-01-01

It is a known fact that the austenizing conditions (speed of heating to the austenite temperature and austenizing time) as well as the initial metallurgical state of the material strongly influence the distribution of austenitic grain size in steels. This distribution will be one of the parameters that will control the behavior of the material in a later transformation from the austenite -by continuous cooling or in the isothermal case - and this behavior will determine the product's final mechanical properties. Based on the published literature, we have studied the influence of the initial metallurgical state and the speed of heating to austenite on the distribution of austenitic grain size for a certain austenizing temperature and time for a martensitic-iron ASTM A213 grade T91 steel. Two-stage thermal cycles were designed for this, that is, tempering for a variable period of time at the industrial tempering temperature (780 o C) followed by the austenizing (1050 o C, 30 minutes) 'in situ'. We have analyzed the following as a whole: 1) the role of the stabilizing elements (Nb, V) that eventually control the anchoring of the austenitic grain boundary by carbide or carbonitride precipitation. Therefore, we have tried to vary the fraction of these elements present in solid solution by annealing before austenizing. 2) the role of the speed of heating to austenite. In this case, we have considered two different values (1 and 30 o C/s), previously reported as inferior and superior, respectively, to the speed of 'critical' heat needed to produce a distribution of heterogeneous austenitic grain size when the metallurgical state before the austenizing is quenched and tempered. Preliminary results suggest that a annealing stage after tempering in the plant and prior to eventual austenizing significantly reduces the influence of the heating to austenite speed in the development of a heterogeneous structure of austenitic grains (CW)

The two faces of coal : uncertainty the common prospect for metallurgical and thermal coal

International Nuclear Information System (INIS)

Zlotnikov, D.

2010-01-01

Although the methods of producing thermal and metallurgical coal are the same, metallurgical coal is destined to cross the world for steel manufacturing and thermal coal is destined for power plants close to where it was mined. This article discussed the factors influencing the price of these 2 coals. The production of thermal coal can remain steady during an economic crisis because coal-fired power plants generally provide low-cost-base-load electricity that remains stable during economic cycles. However, the demand for metallurgical coal is more volatile during an economic crisis because it is directly related to the demand for steel products in the construction and automotive industry, which are very sensitive to the state of the economy. There have been recent indications that Canada's export market for thermal coal is on the rise. In 2008, China became a net importer of coking coal. China's need for more coal to fuel its growing economy despite the global economic slowdown has meant that producers are diverting excess supply from European markets to China. Higher-end thermal coal offers low sulphur content and higher energy content, both desirable traits for power utilities facing strict emissions control. In addition to having huge reserves of very high-quality coal that is becoming increasingly important to China, Canada has the advantage of having the available transportation capacity in its west coast terminals and on its rail network. 3 figs.

On the Critical Role of Divergent Selection in Evolvability

Directory of Open Access Journals (Sweden)

Joel Lehman

2016-08-01

Full Text Available An ambitious goal in evolutionary robotics is to evolve increasingly complex robotic behaviors with minimal human design effort. Reaching this goal requires evolutionary algorithms that can unlock from genetic encodings their latent potential for evolvability. One issue clouding this goal is conceptual confusion about evolvability, which often obscures the aspects of evolvability that are important or desirable. The danger from such confusion is that it may establish unrealistic goals for evolvability that prove unproductive in practice. An important issue separate from conceptual confusion is the common misalignment between selection and evolvability in evolutionary robotics. While more expressive encodings can represent higher-level adaptations (e.g. sexual reproduction or developmental systems that increase long-term evolutionary potential (i.e. evolvability, realizing such potential requires gradients of fitness and evolvability to align. In other words, selection is often a critical factor limiting increasing evolvability. Thus, drawing from a series of recent papers, this article seeks to both (1 clarify and focus the ways in which the term evolvability is used within artificial evolution, and (2 argue for the importance of one type of selection, i.e. divergent selection, for enabling evolvability. The main argument is that there is a fundamental connection between divergent selection and evolvability (on both the individual and population level that does not hold for typical goal-oriented selection. The conclusion is that selection pressure plays a critical role in realizing the potential for evolvability, and that divergent selection in particular provides a principled mechanism for encouraging evolvability in artificial evolution.

Some results of medical researches at Ulba Metallurgical Plant

Energy Technology Data Exchange (ETDEWEB)

Artemieva, G.I.; Novikov, V.G.; Savchuk, V.V. [Ulba Metallurgical Plant, Ust-Kamenogorsk (Kazakhstan)

1998-01-01

The results of 45-years medical researches at beryllium production of Ulba Metallurgical Plant are summarized in this report. Statistic data on different kinds of occupational diseases, related to beryllium production and the dynamics of changing occupational diseases with the development of beryllium production, are given there. Data on average duration of life of occupational disease patients are presented in the report. It includes the description of problems, related to berylliosis diagnosis. Issues, connected to beryllium production effect on health of man, located nearby beryllium production are also discussed there as well. (author)

Relationship between turbine rotor and disk metallurgical characteristics and stress corrosion cracking behavior. Final report

International Nuclear Information System (INIS)

Gayley, H.B.

1986-09-01

This report describes stress corrosion test results in which several heats of turbine rotor steels specially prepared to achieve different degrees of segregation to the grain boundaries were tested in concentrated laboratory and actual steam turbine environments. Grain boundary characteristics are considered important because turbine rotor failures in field service have been of an intergranular nature and because grain boundary segregation is known to affect the impact toughness of rotor steels (''temper embrittlement''). The laboratory stress corrosion testing results showed no differences between heavily and lightly segregated test pieces which differed greatly in impact toughness. All test specimens cracked, indicating the laboratory environments may have been too severe to allow differentiation between the various metallurgical conditions, if any differences exist. Test loops and autoclaves for chemical analysis and mechanical testing were designed, installed and are operating in the field testing portion of this program. No intergranular cracking has occurred to date; hence, no differentiation between heavily and lightly segregated test pieces has been possible in field testing. Instrumented crack propagation specimens, which permit measurement of cracking as it occurs, have been installed for the continuing field testing program. Correlation of such cracking with the continuously monitored chemical composition of the environment will increase understanding of the cracking process and may give the possibility of providing an early warning of the existence of conditions which might cause turbine rotor cracking

Regional distribution of the metallurgical industry in the Czech Republic

OpenAIRE

T. Sadilek

2017-01-01

The aim of the article is to present the regional distribution of the metallurgical industry in the Czech Republic and to describe the specific factors which determine the localization of the industry in Czech regions. In order to achieve that goal, traditional tools of regional analysis are used, such as concentration analysis, used in business-to-business marketing, which does not describe the absolute size of the industry, but its relative size, focusing on the relation between the employe...

AUTOMATION OF OPERATIONAL CONTROL OF DATA FLOWS OF THE METALLURGICAL ENTERPRISE ORGANIZATIONAL STRUCTURE

Directory of Open Access Journals (Sweden)

A. N. Chichko

2006-01-01

Full Text Available New method for creation of models of operative control of enterprise is offered. The computer variant of the organizational structure, based on analysis of the charging dynamics of control units, is offered and illustrated at the example of one of organizational structures of Belorussian metallurgical works.

Metallurgical flow recognition by random signal analysis of stress wave emissions

International Nuclear Information System (INIS)

Woodward, B.

1973-01-01

The present study involves detailed random signal analysis of individual 'bursts' of emission with objective of 'reading' their frequency spectra to identify specific metallurgical mechanisms. Mild steel unnotched testpieces were used in the early stages of development of this research. From a fracture mechanics point of view this research could lead to a powerful nondestructive testing device allowing identification of interior, instead of only surface, deformation mechanisms. (author)

Evaluation of the properties of the CaCO3CaO system for metallurgical use

International Nuclear Information System (INIS)

Tapia, O.; Grijalva, M.; Rodriguez, A.; Formoso, A.

1999-01-01

The principal goal of this work, is to make a preliminary and comparative study on the physical chemistry, structural and thermal properties of the metallurgical lime production using experimental, and in some cases industrial measurements. This is important, because the characterization of the CaCO 3 CaO system, predicts the dissolution grade of the lime on the slag solution in the steel making. The mineral is located on the border of Michoacan (Lazaro Cardenas)and the Guerrero states (La Union) Mexico. This study evidences limited properties of this lime, which is due to the thermal and physical chemistry behaviour of the obtained results of this material. However, it is necessary to make a study in the future about the kinetic behavior during decomposition. This is necessary because it is important to obtain an increase in the basic oxides concentration and a decrease in the loss of ignition, which is important for the competitive lime production. (Author) 25 refs

Recycling of rubber tires in electric arc furnace steelmaking: simultaneous combustion of metallurgical coke and rubber tyres blends

Energy Technology Data Exchange (ETDEWEB)

Magdalena Zaharia; Veena Sahajwalla; Byong-Chul Kim; Rita Khanna; N. Saha-Chaudhury; Paul O' Kane; Jonathan Dicker; Catherine Skidmore; David Knights [University of New South Wales, Sydney, NSW (Australia). School of Materials Science and Engineering

2009-05-15

The present study investigates the effect of addition of waste rubber tires on the combustion behavior of its blends with coke for carbon injection in electric arc furnace steelmaking. Waste rubber tires were mixed in different proportions with metallurgical coke (MC) (10:90, 20:80, 30:70) for combustion and pyrolysis at 1473 K in a drop tube furnace (DTF) and thermogravimetric analyzer (TGA), respectively. Under experimental conditions most of the rubber blends indicated higher combustion efficiencies compared to those of the constituent coke. In the early stage of combustion the weight loss rate of the blends is much faster compared to that of the raw coke due to the higher volatile yield of rubber. The presence of rubber in the blends may have had an impact upon the structure during the release and combustion of their high volatile matter (VM) and hence increased char burnout. Measurements of micropore surface area and bulk density of the chars collected after combustion support the higher combustion efficiency of the blends in comparison to coke alone. The surface morphology of the 30% rubber blend revealed pores in the residual char that might be attributed to volatile evolution during high temperature reaction in oxygen atmosphere. Physical properties and VM appear to have a major effect upon the measured combustion efficiency of rubber blends. The study demonstrates that waste rubber tires can be successfully co-injected with metallurgical coke in electric arc furnace steelmaking process to provide additional energy from combustion. 44 refs., 11 figs., 2 tabs.

Measures to restore metallurgical mine wasteland using ecological restoration technologies: A case study at Longnan Rare Earth Mine

Science.gov (United States)

Rao, Yunzhang; Gu, Ruizhi; Guo, Ruikai; Zhang, Xueyan

2017-01-01

Whereas mining activities produce the raw materials that are crucial to economic growth, such activities leave extensive scarring on the land, contributing to the waste of valuable land resources and upsetting the ecological environment. The aim of this study is therefore to investigate various ecological technologies to restore metallurgical mine wastelands. These technologies include measures such as soil amelioration, vegetation restoration, different vegetation planting patterns, and engineering technologies. The Longnan Rare Earth Mine in the Jiangxi Province of China is used as the case study. The ecological restoration process provides a favourable reference for the restoration of a metallurgical mine wasteland.

Modeling and clustering users with evolving profiles in usage streams

KAUST Repository

Zhang, Chongsheng; Masseglia, Florent; Zhang, Xiangliang

2012-01-01

Today, there is an increasing need of data stream mining technology to discover important patterns on the fly. Existing data stream models and algorithms commonly assume that users' records or profiles in data streams will not be updated or revised once they arrive. Nevertheless, in various applications such asWeb usage, the records/profiles of the users can evolve along time. This kind of streaming data evolves in two forms, the streaming of tuples or transactions as in the case of traditional data streams, and more importantly, the evolving of user records/profiles inside the streams. Such data streams bring difficulties on modeling and clustering for exploring users' behaviors. In this paper, we propose three models to summarize this kind of data streams, which are the batch model, the Evolving Objects (EO) model and the Dynamic Data Stream (DDS) model. Through creating, updating and deleting user profiles, these models summarize the behaviors of each user as a profile object. Based upon these models, clustering algorithms are employed to discover interesting user groups from the profile objects. We have evaluated all the proposed models on a large real-world data set, showing that the DDS model summarizes the data streams with evolving tuples more efficiently and effectively, and provides better basis for clustering users than the other two models. © 2012 IEEE.

Modeling and clustering users with evolving profiles in usage streams

KAUST Repository

Zhang, Chongsheng

2012-09-01

Today, there is an increasing need of data stream mining technology to discover important patterns on the fly. Existing data stream models and algorithms commonly assume that users\\' records or profiles in data streams will not be updated or revised once they arrive. Nevertheless, in various applications such asWeb usage, the records/profiles of the users can evolve along time. This kind of streaming data evolves in two forms, the streaming of tuples or transactions as in the case of traditional data streams, and more importantly, the evolving of user records/profiles inside the streams. Such data streams bring difficulties on modeling and clustering for exploring users\\' behaviors. In this paper, we propose three models to summarize this kind of data streams, which are the batch model, the Evolving Objects (EO) model and the Dynamic Data Stream (DDS) model. Through creating, updating and deleting user profiles, these models summarize the behaviors of each user as a profile object. Based upon these models, clustering algorithms are employed to discover interesting user groups from the profile objects. We have evaluated all the proposed models on a large real-world data set, showing that the DDS model summarizes the data streams with evolving tuples more efficiently and effectively, and provides better basis for clustering users than the other two models. © 2012 IEEE.

Explosion bonding of dissimilar materials for fabricating APS front end components: Analysis of metallurgical and mechanical properties and UHV applications

International Nuclear Information System (INIS)

Li, Yuheng; Shu, Deming; Kuzay, T.M.

1994-01-01

The front end beamline section contains photon shutters and fixed masks. These components are made of OFHC copper and GlidCOP AL-15. Stainless steels (304 or 316) are also used for connecting photon shutters and fixed masks to other components that operate in the ultrahigh vacuum system. All these dissimilar materials need to be joined together. However, bonding these dissimilar materials is very difficult because of their different mechanical and thermal properties and incompatible metallurgical properties. Explosion bonding is a bonding method in which the controlled energy of a detonating explosive is used to create a metallurgical bond between two or more similar or dissimilar materials. No intermediate filler metal, for example, a brazing compound or soldering alloy, is needed to promote bonding, and no external heat need be applied. A study of the metallurgical and mechanical properties and YGV applications of GlidCop AL-15, OFHC copper, and 304 stainless steel explosion-bonded joints has been done. This report contains five parts: an ultrasonic examination of explosion-bonded joints and a standard setup; mechanical-property and thermal-cycle tests of GlidCop AL-15/304 stainless steel explosion-bonded joints; leak tests of a GlidCop AL-15/304 stainless steel explosion-bonded interfaces for UHV application; metallurgical examination of explosion-bonded interfaces and failure analysis, and discussion and conclusion

Metallurgical bond between magnesium AZ91 alloy and aluminium plasma sprayed coatings

Czech Academy of Sciences Publication Activity Database

Kubatík, Tomáš František; Pala, Zdeněk; Neufuss, Karel; Vilémová, Monika; Mušálek, Radek; Stoulil, J.; Slepička, P.; Chráska, Tomáš

2015-01-01

Roč. 282, November (2015), s. 163-170 ISSN 0257-8972 R&D Projects: GA ČR(CZ) GP14-31538P Institutional support: RVO:61389021 Keywords : Plasma spraying * AZ91 magnesium alloy * Aluminium * Metallurgical bond * X-ray diffraction Subject RIV: JK - Corrosion ; Surface Treatment of Materials Impact factor: 2.139, year: 2015 http://www.sciencedirect.com/science/article/pii/S0257897215303297

Study of the Metallurgical Aspects of Steel Micro-Alloying by Titan

Directory of Open Access Journals (Sweden)

Kijac, J.

2006-01-01

Full Text Available The metal properties upgrading applying it’s alloying with the simultaneous limitation of the impurities represents a prospective possibility of the metallurgical production further development. The interaction of the alloying substance active element with oxygen in metal and adjacent multiphase environment occurs under the actual conditions. Present paper is oriented particularly to the thermodynamic aspects of deoxygenation by titan in process of production of micro alloyed low carbon steel in two plants (oxygen converter 1-OC1 and 2-OC2 with the different effect of micro-alloy exploitation. Analysis of the effect of the metallurgical factors on the titan smelting loss in micro-alloyed steel production points at the need to master the metal preparation for the alloying and especially has got the decisive effect upon the oxidizing ability and rate of the slag phase availability. When comparing the micro-alloying matter yield among the individual production units, disclosed have been better results obtained in plant OC 2. Confirmed has been the effect of the slag amount (average amount of 7,3 t at OC 1 and 5,83 t at OC 2 and its quality during the steel tapping as one among the most significant factors affecting the alloying process and which also represent its oxidizing potential.

Conservation of mining and metallurgic arachaeologic wooden objects by impregnation and radiation curing

International Nuclear Information System (INIS)

Schaudy, R.; Slais, E.; Eibner, C.

1983-05-01

The conservation of mining and metallurgic archaeologic wooden objects of different grade of destruction by impregnation with radiation-curable impregnating agents followed by in-situ-curing with gamma rays is described. Dry objects have been consolidated after cautious cleaning, whereas wet findings had to be freezedried first. The results are discussed. (Author) [de

Wear and corrosion performance of metallurgical coatings in sodium

International Nuclear Information System (INIS)

Johnson, R.N.; Farwick, D.G.

1980-01-01

The friction, wear, and corrosion performance of several metallurgical coatings in 200 to 650 0 C sodium are reviewed. Emphasis is placed on those coatings which have successfully passed the qualification tests necessary for acceptance in breeder reactor environments. Tests include friction, wear, corrosion, thermal cycling, self-welding, and irradiation exposure under as-prototypic-as-possible service conditions. Materials tested were coatings of various refractory metal carbides in metallic binders, nickel-base and cobalt-base alloys and intermetallic compounds such as the aluminides and borides. Coating processes evaluated included plasma spray, detonation gun, sputtering, spark-deposition, and solid-state diffusion

Metallurgical aspects of corrosion resistance of aluminium alloys

Energy Technology Data Exchange (ETDEWEB)

Reboul, M.C. [Pechiney Voreppe Research Centre France (France); CNRS-INP Grenoble, SIMAP-INP Grenoble, Universite France, Saint Martin d' Heres Cedex (France); Baroux, B. [SIMAP-INP, Grenoble University, 1130 rue de la piscine, Saint Martin d' Heres Cedex (France)

2011-03-15

Aluminium is the second most often used metal after steel. In this paper, the most current uses of aluminium alloys are first summarised. Then, their different corrosion modes, i.e. pitting, crevice, filiform, galvanic and structural corrosion (including inter-granular, exfoliation and stress corrosion cracking) are reviewed, with particular attention paid to metallurgical factors controlling the corrosion process. For each mode, some instances of possible in-service failure are given, followed by the discussion of the involved mechanisms and the presentation of appropriate solutions to prevent corrosion. Last, passivity and polarisation behaviour are discussed with reference to stainless steels. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Mechanical and Metallurgical Properties of Various Nickel-Titanium Rotary Instruments

OpenAIRE

Shim, Kyu-Sang; Oh, Soram; Kum, KeeYeon; Kim, Yu-Chan; Jee, Kwang-Koo; Chang, Seok Woo

2017-01-01

The aim of this study was to investigate the effect of thermomechanical treatment on mechanical and metallurgical properties of nickel-titanium (NiTi) rotary instruments. Eight kinds of NiTi rotary instruments with sizes of ISO #25 were selected: ProFile, K3, and One Shape for the conventional alloy; ProTaper NEXT, Reciproc, and WaveOne for the M-wire alloy; HyFlex CM for the controlled memory- (CM-) wire; and TF for the R-phase alloy. Torsional fracture and cyclic fatigue fracture tests were...

Key Lake Mining Corporation metallurgical complex

International Nuclear Information System (INIS)

Lendrum, F.C.

1984-02-01

The Key Lake uranium mine is located in Saskatchewan, 550 km northeast of Saskatoon. It began operations in 1983, and is licensed and regulated by both Saskatchewan government agencies and the Canadian Atomic Energy Control Board. This report examines the metallurgical processes used at the mill and discusses the spills that occurred in the first four months the mine was in operation. It finds that all spills of an acidic nature in the mill were small amounts in the CCD or solution pretreatment sections. Contingency procedures are in place and sumps are capable of handling spills. The only major change in design contemplated will be converting the secondary crushing from the use of an impact crusher to the use of a semi-autogeneous grinding mill. The monitoring program set out by the AECB and Saskatchewan Environment is thorough. It monitors effluents and water pathways, and includes aquatic biota and sediments. Air monitoring is also required by Saskatchewan Environment

Highly sensitive luminescence method of scandium determination in the products of metallurgical reprocessing

International Nuclear Information System (INIS)

Matveets, M.A.; Akhmetova, S.D.

1988-01-01

Highly sensitive reaction of scandium with 1,10-phenanthroline and eosin is used for the development of luminescence method of its determination in metallurgical products. The effect of interfering elements is eliminated by scandium extraction with monocarboxylic acids. The method permits to determine scandium content from 5 x 10 -5 % (Sr 0.15 - 0.25)

Automatic Processing of Metallurgical Abstracts for the Purpose of Information Retrieval. Final Report.

Science.gov (United States)

Melton, Jessica S.

Objectives of this project were to develop and test a method for automatically processing the text of abstracts for a document retrieval system. The test corpus consisted of 768 abstracts from the metallurgical section of Chemical Abstracts (CA). The system, based on a subject indexing rational, had two components: (1) a stored dictionary of words…

Evolving Neural Turing Machines for Reward-based Learning

DEFF Research Database (Denmark)

Greve, Rasmus Boll; Jacobsen, Emil Juul; Risi, Sebastian

2016-01-01

An unsolved problem in neuroevolution (NE) is to evolve artificial neural networks (ANN) that can store and use information to change their behavior online. While plastic neural networks have shown promise in this context, they have difficulties retaining information over longer periods of time...... version of the double T-Maze, a complex reinforcement-like learning problem. In the T-Maze learning task the agent uses the memory bank to display adaptive behavior that normally requires a plastic ANN, thereby suggesting a complementary and effective mechanism for adaptive behavior in NE....

Metallurgical Characterization of Reduced Activation Martensitic Steel F-82H Modified

International Nuclear Information System (INIS)

Fernandez, P.; Lapena, J.; Lancha, A.M.; Gomez-Briceno, D.; Schirra, M.

1999-12-01

During 1995-1998 within of research and development programs on reduced ferritic/martensitic steels for fusion, metallurgical characterization of 8Cr-2WVTa steel, denominated F-28H modified, have been carried out. The work has focused on studying the microstructural and mechanical (tensile, creep, low cycle fatigue and charpy) characteristics of as-received state and aged material in the temperature range 300 degree centigrade to 600 degree centigrade for periods up to 5000 h. (Author) 45 refs

Fatigue analysis of a structure with welds considering metallurgical discontinuities

International Nuclear Information System (INIS)

Cabrillat, M.T.; Lejeail, Y.

1995-01-01

Within the frameworks of a creep-fatigue experimental program, called EVASION, thermo-mechanical tests were conducted on two mock-ups, the first one was fully machined and the second one welded and then machined (in order to eliminate geometrical discontinuities, thus only leaving metallurgical discontinuities). These two mock-ups were submitted to exactly the same loading history. Plastic analyses with a correct description of mechanical properties and fatigue strength of materials are conducted and compared with experimental results in order to highlight the influence of the weld. (author). 3 refs., 4 figs., 3 tabs

Magnetohydrodynamic research in fusion blanket engineering and metallurgical processing

International Nuclear Information System (INIS)

Tokuhiro, A.

1991-11-01

A review of recent research activities in liquid metal magnetohydrodynamics (LM-MHDs) is presented in this article. Two major reserach areas are discussed. The first topic involves the thermomechanical design issues in a proposed tokamak fusion reactor. The primary concerns are in the magneto-thermal-hydraulic performance of a self-cooled liquid metal blanket. The second topic involves the application of MHD in material processing in the metallurgical and semiconductor industries. The two representative applications are electromagnetic stirring (EMS) of continuously cast steel and the Czochralski (CZ) method of crystal growth in the presence of a magnetic field. (author) 24 figs., 10 tabs., 136 refs

Obtaining of dense and highly porous ceramic materials from metallurgical slag

OpenAIRE

Fidancevska E.; Mangutova B.; Milosevski D.; Milosevski M.; Bossert J.

2003-01-01

Glass-ceramics in a dense and highly porous form can be obtained from metallurgical slag and waste glass of TV monitors. Using polyurethane foam as pore creator, a highly porous system with porosity of 65 ± 5 %, E-modulus and flexural strength of 8 ± 3 GPa and 13 ± 3.5 MPa respectively can be obtained. This porous material had durability (mass loss) of 0.03 % in 0.1 M HCl that is identical with the durability of a dense composite.

Effect of glass-ceramic-processing cycle on the metallurgical properties of candidate alloys for actuator housings

Energy Technology Data Exchange (ETDEWEB)

Weirick, L.J.

1982-01-01

This report summarizes the results from an investigation on the effect of a glass ceramic processing cycle on the metallurgical properties of metal candidates for actuator housings. The cycle consists of a 980/sup 0/C sealing step, a 650/sup 0/C crystallization step and a 475/sup 0/C annealing step. These temperatue excursions are within the same temperature regime as annealing and heat treating processes normally employed for metals. Therefore, the effect of the processing cycle on metallurgical properties of microstructure, strength, hardness and ductility were examined. It was found that metal candidates which are single phase or solid solution alloys (such as 21-6-9, Hastelloy C-276 and Inconel 625) were not affected whereas multiphase or precipitation hardened alloys (such as Inconel 718 and Titanium ..beta..-C) were changed by the processing cycle for the glass ceramic.

Bio-alteration of metallurgical wastes by Pseudomonas aeruginosa in a semi flow-through reactor.

Science.gov (United States)

van Hullebusch, Eric D; Yin, Nang-Htay; Seignez, Nicolas; Labanowski, Jérôme; Gauthier, Arnaud; Lens, Piet N L; Avril, Caroline; Sivry, Yann

2015-01-01

Metallurgical activities can generate a huge amount of partially vitrified waste products which are either landfilled or recycled. Lead Blast Furnace (LBF) slags are often disposed of in the vicinity of metallurgical plants, and are prone to weathering, releasing potentially toxic chemical components into the local environment. To simulate natural weathering in a slag heap, bioweathering of these LBF slags was studied in the presence of a pure heterotrophic bacterial strain (Pseudomonas aeruginosa) and in a semi-flow through reactor with intermittent leachate renewal. The evolution of water chemistry, slag composition and texture were monitored during the experiments. The cumulative bulk release of dissolved Fe, Si, Ca and Mg doubled in the presence of bacteria, probably due to the release of soluble complexing organic molecules (e.g. siderophores). In addition, bacterial biomass served as the bioadsorbent for Pb, Fe and Zn as 70-80% of Pb and Fe, 40-60% of Zn released are attached to and immobilized by the bacterial biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

Metallurgical characterization of pulsed current gas tungsten arc, friction stir and laser beam welded AZ31B magnesium alloy joints

International Nuclear Information System (INIS)

Padmanaban, G.; Balasubramanian, V.

2011-01-01

This paper reports the influences of welding processes such as friction stir welding (FSW), laser beam welding (LBW) and pulsed current gas tungsten arc welding (PCGTAW) on mechanical and metallurgical properties of AZ31B magnesium alloy. Optical microscopy, scanning electron microscopy, transmission electron microscopy and X-Ray diffraction technique were used to evaluate the metallurgical characteristics of welded joints. LBW joints exhibited superior tensile properties compared to FSW and PCGTAW joints due to the formation of finer grains in weld region, higher fusion zone hardness, the absence of heat affected zone, presence of uniformly distributed finer precipitates in weld region.

EXPERIENCE AND PROSPECTS OF MASTER’S DEGREE TRAINING OF ENGINEERING STAFF IN THE FIELD OF METALLURGICAL SCIENCE

Directory of Open Access Journals (Sweden)

V. M. Konstantinov

2016-01-01

Full Text Available The experience of training for MBA in engineering and technologies for specialties “Materials Science in Mechanical Engineering” at the department was analyzed. Efficiency of the practical-focused Master’s degree program for engineering staff of the machine-building and metallurgical enterprises was emphasized. Some ways to increase efficiency of master training of engineering experts in the field of metallurgical science and heat treatment are offered. Need of more active interaction with engineering services of the production enterprise during implementation of the master thesis was proved. Need of domination of requirements of the production enterprise is highlighted in master preparation program. The algorithm of interaction of department and technical service of the production enterprise during training of the factory expert in the correspondence practical-focused Master’s degree program is offered.

Obtaining of dense and highly porous ceramic materials from metallurgical slag

Directory of Open Access Journals (Sweden)

Fidancevska E.

2003-01-01

Full Text Available Glass-ceramics in a dense and highly porous form can be obtained from metallurgical slag and waste glass of TV monitors. Using polyurethane foam as pore creator, a highly porous system with porosity of 65 ± 5 %, E-modulus and flexural strength of 8 ± 3 GPa and 13 ± 3.5 MPa respectively can be obtained. This porous material had durability (mass loss of 0.03 % in 0.1 M HCl that is identical with the durability of a dense composite.

First Mining workshop of Mining and metallurgical of MERCOSUR

International Nuclear Information System (INIS)

1994-01-01

In the city of Montevideo, capital of the Oriental Republic of Uruguay, at 23 days of September 1994, under the First Meeting of Mercosur Mining Metallurgical, meet representatives of the mining sector in the countries signed the Treaty of Asuncion , attended as observers, authorities of the Republic of Bolivia and Ecuador and representatives of the productive labor, legislative and research. The primary objective is to integrate the mining sectors of those countries, taking into account the specificity of the mining, given by the resource it uses, the need for high-risk investment with slow recoveries of capital and infrastructure problems, taking into account leverage and its remarkable impact on the development of regional economies.

Morphology, chemistry and distribution of neoformed spherulites in agricultural land affected by metallurgical point-source pollution

NARCIS (Netherlands)

Leguedois, S.; Oort, van F.; Jongmans, A.G.; Chevalier, P.

2004-01-01

Metal distribution patterns in superficial soil horizons of agricultural land affected by metallurgical point-source pollution were studied using optical and electron microscopy, synchrotron radiation and spectroscopy analyses. The site is located in northern France, at the center of a former entry

Metallurgical Design and Development of NASA Crawler/Transporter Tread Belt Shoe Castings

Science.gov (United States)

Parker, Donald S.

2006-01-01

The NASA Crawler/Transporters (CT-1 and CT-2) used to transport the Space Shuffles are one of the largest tracked vehicles in existence today. Two of these machines have been used to move space flight vehicles at Kennedy Space Center since the Apollo missions of the 1960's and relatively few modifications have been made to keep them operational. In September of 2003 during normal Crawler/Transporter operations cracks were observed along the roller pad surfaces of several tread belt shoes. Further examination showed 20 cracked shoes on CT-1 and 40 cracked shoes on CT-2 and a formal failure analysis investigation was undertaken while the cracked shoes were replaced. Six shoes were cross-sectioned with the fracture surfaces exposed and it was determined that the cracks were due to fatigue that initiated on the internal casting web channels at pre-existing casting defects and propagated through thickness both transgranularly and intergranularly between internal shrinkage cavities, porosity, and along austenitic and ferritic grain boundaries. The original shoes were cast during the 1960's using a modified 861330 steel with slightly higher levels of chromium, nickel and molybdenum followed by heat treatment to achieve a minimum tensile strength of 11 Oksi. Subsequent metallurgical analysis of the tread belt shoes after multiple failures showed excessive internal defects, alloy segregation, a nonuniform ferritic/ bainitic/martensitic microstructure, and low average tensile properties indicative of poor casting and poor heat-treatment. As a result, NASA funded an initiative to replace all of the tread belt shoes on both crawler/transporters along with a redesign of the alloy, manufacturing, and heat-treatment to create a homogeneous cast structure with uniform mechanical and metallurgical properties. ME Global, a wholly owned subsidiary of ME Elecmetal based in Minneapolis, MN was selected as manufacturing and design partner to develop the new shoes and this paper

Perspectives regarding the use of metallurgical slags as secondary metal resources - A review of bioleaching approaches.

Science.gov (United States)

Potysz, Anna; van Hullebusch, Eric D; Kierczak, Jakub

2018-05-05

Smelting activity by its very nature produces large amounts of metal-bearing waste, often called metallurgical slag(s). In the past, industry used to dispose of these waste products at dumping sites without the appropriate environmental oversight. Once there, ongoing biogeochemical processes affect the stability of the slags and cause the release of metallic contaminants. Rather than viewing metallurgical slags as waste, however, such deposits should be viewed as secondary metal resources. Metal bioleaching is a "green" treatment route for metallurgical slags, currently being studied under laboratory conditions. Metal-laden leachates obtained at the bioleaching stage have to be subjected to further recovery operations in order to obtain metal(s) of interest to achieve the highest levels of purity possible. This perspective paper considers the feasibility of the reuse of base-metal slags as secondary metal resources. Special focus is given to current laboratory bioleaching approaches and associated processing obstacles. Further directions of research for development of more efficient methods for waste slag treatment are also highlighted. The optimized procedure for slag treatment is defined as the result of this review and should include following steps: i) slag characterization (chemical and phase composition and buffering capacity) following the choice of initial pH, ii) the choice of particle size, iii) the choice of the liquid-to-solid ratio, iv) the choice of microorganisms, v) the choice of optimal nutrient supply (growth medium composition). An optimal combination of all these parameters will lead to efficient extraction and generation of metal-free solid residue. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effective recruitment method for the marketing department of a metallurgical enterprise

Directory of Open Access Journals (Sweden)

E. Jaba

2014-04-01

Full Text Available This paper presents some solutions to recruit staff for the Marketing Department of a metallurgical enterprise. Our goal is to present the psychological characteristics of a certain category of employees on a sample of 107 employees and to evaluate the relationship between the motivation to work and those characteristics. In order to realize such evaluation we used the linear mixed effects model in the statistical software program R. The results showed that a significant effect on work motivation have factors like work climate and the employee agreeability.

A multi-level code for metallurgical effects in metal-forming processes

Energy Technology Data Exchange (ETDEWEB)

Taylor, P.A.; Silling, S.A. [Sandia National Labs., Albuquerque, NM (United States). Computational Physics and Mechanics Dept.; Hughes, D.A.; Bammann, D.J.; Chiesa, M.L. [Sandia National Labs., Livermore, CA (United States)

1997-08-01

The authors present the final report on a Laboratory-Directed Research and Development (LDRD) project, A Multi-level Code for Metallurgical Effects in metal-Forming Processes, performed during the fiscal years 1995 and 1996. The project focused on the development of new modeling capabilities for simulating forging and extrusion processes that typically display phenomenology occurring on two different length scales. In support of model fitting and code validation, ring compression and extrusion experiments were performed on 304L stainless steel, a material of interest in DOE nuclear weapons applications.

Carbonitriding of low alloy steels: Mechanical and metallurgical responses

Energy Technology Data Exchange (ETDEWEB)

Dal' Maz Silva, W., E-mail: waltermateriais@me.com [Institut Jean Lamour – UMR CNRS–Université de Lorraine, 7198, Parc de Saurupt, Nancy 54011 (France); Institut de Recherche Technologique M2P, Metz 57070 (France); Dulcy, J., E-mail: jacky.dulcy@univ-lorraine.fr [Institut Jean Lamour – UMR CNRS–Université de Lorraine, 7198, Parc de Saurupt, Nancy 54011 (France); Ghanbaja, J., E-mail: jaafar.ghanbaja@univ-lorraine.fr [Institut Jean Lamour – UMR CNRS–Université de Lorraine, 7198, Parc de Saurupt, Nancy 54011 (France); Redjaïmia, A., E-mail: abdelkrim.redjaimia@univ-lorraine.fr [Institut Jean Lamour – UMR CNRS–Université de Lorraine, 7198, Parc de Saurupt, Nancy 54011 (France); Michel, G., E-mail: gregory.michel@irt-m2p.fr [Institut de Recherche Technologique M2P, Metz 57070 (France); Thibault, S., E-mail: simon.thibault@safran.fr [Safran Tech, Magny les Hameaux (France); Belmonte, T., E-mail: thierry.belmonte@univ-lorraine.fr [Institut Jean Lamour – UMR CNRS–Université de Lorraine, 7198, Parc de Saurupt, Nancy 54011 (France)

2017-05-02

Metallurgical and mechanical responses of alloys 16NiCrMo13 and 23MnCrMo5 to the addition of carbon and/or nitrogen were investigated. Diffusion profiles of these interstitial elements were established by atmospheric pressure carburizing, austenitic nitriding, and a sequence of carburizing and nitriding – the carbonitriding. All treatments were performed at 1173 K under CO-H{sub 2} and/or NH{sub 3} based atmospheres. After enrichment, each sample was (i) room-temperature oil-quenched and (ii) immersed in boiling nitrogen prior to (iii) the stress relief treatment. Cross-section hardness profiles were evaluated after each of these steps. Electron probe microanalysis (EPMA) allowed for the determination of both carbon and nitrogen diffusion profiles after quenching. In order to estimate the fraction of nitrides formed during the enrichment of the alloys, these measured profiles were employed in the simulation of local equilibrium at each evaluated position. This allowed for the computation of total solid solution interstitial content, which was expressed in atomic fraction. Plots of as-quenched hardness against the square root of the computed interstitial content, i.e. the sum of solution carbon and the remaining nitrogen, show the complementary character of these elements in determining the mechanical properties of the materials prior to stress relief treatment. Tempering of carbon-nitrogen martensite resulted in hardness drop to a lesser degree than the one measured on carbon martensite with equivalent interstitial content. In order to investigate this behavior, transmission electron microscopy (TEM) analyses were performed. Results showed the precipitation of two morphologies of Fe{sub 16}N{sub 2} in the nitrogen-rich case and image analysis confirmed the simulated fraction of nitrides.

Municipal solid waste disposal by using metallurgical technologies and equipments

Energy Technology Data Exchange (ETDEWEB)

Cai, Jiuju; Sun, Wenqiang [State Environmental Protection Key Laboratory of Eco-industry, Institute of Thermal and Environmental Engineering, Northeastern University, Shenyang 110819 (China)

2012-07-01

Pyrolysis of municipal solid waste can take full advantage of energy and resource and avoid producing hazardous material during this period. In combination with mature metallurgical technologies of coking by coke oven, regenerative flame furnace technology and melting by electric arc furnace, technologies of regenerative fixed bed pyrolysis technology for household waste, co-coking technology for waste plastic and blend coal, and incineration ash melting technology by electric arc technology for medical waste were respectively developed to improve current unsatisfied sorting status of waste. The investigation results of laboratory experiments, semi-industrial experiments and industrial experiments as well as their economic benefits and environmental benefits for related technologies were separately presented.

Characterization of Tool Wear in High-Speed Milling of Hardened Powder Metallurgical Steels

Directory of Open Access Journals (Sweden)

Fritz Klocke

2011-01-01

Full Text Available In this experimental study, the cutting performance of ball-end mills in high-speed dry-hard milling of powder metallurgical steels was investigated. The cutting performance of the milling tools was mainly evaluated in terms of cutting length, tool wear, and cutting forces. Two different types of hardened steels were machined, the cold working steel HS 4-2-4 PM (K490 Microclean/66 HRC and the high speed steel HS 6-5-3 PM (S790 Microclean/64 HRC. The milling tests were performed at effective cutting speeds of 225, 300, and 400 m/min with a four fluted solid carbide ball-end mill (0 = 6, TiAlN coating. It was observed that by means of analytically optimised chipping parameters and increased cutting speed, the tool life can be drastically enhanced. Further, in machining the harder material HS 4-2-4 PM, the tool life is up to three times in regard to the less harder material HS 6-5-3 PM. Thus, it can be assumed that not only the hardness of the material to be machined plays a vital role for the high-speed dry-hard cutting performance, but also the microstructure and thermal characteristics of the investigated powder metallurgical steels in their hardened state.

Metals, words and gods. Early knowledge of metallurgical skills in Europe, and reflections in terminology

Directory of Open Access Journals (Sweden)

Solin Paliga

1993-12-01

Full Text Available How can metallurgical terminology - specifically names of metals - support ar­ chaeological investigation? Can comparative linguistics and archaeology co-operate in order to identify the emergence and development of metallurgical skills? How did Neolithic and Bronze Age man imagine the taming of nature in order to achieve metal artifacts? Such questions -and many others -may arise whenever we try to investigate the beginnings and making of civilization. It is clear that the various aspects connected to archaeometallurgy cannot be analyzed separately from other aspects of human life, like agriculture, trade, urbanization, religious beliefs, early writing systems, pottery techniques, a.o. The earliest known (or identifiable names of metals do reflect a cer­ tain ideology and a certain way of 'seeing' metals as imbued with magic powers. It is certain that colours and reflections - specific to metals - made early man interpret them as divine (Biek and Bayley 1979; Muşu 1981, chapter Symphony of colours, a first attempt in reconstructing pre-Greek names of colours.

[Hygienic assessment of metal-lurgical slag crushed stone for its use in road-building].

Science.gov (United States)

Tikhomirov, Iu P; Ippolitova, V P; Bezrokov, M E

2010-01-01

The increasing amount of industrial waste generates a need for its use as recycled materials. The paper presents the results of hygienic assessment of metallurgic slag crushed stone to be added to natural materials in highway building. The research program has included the measurement of content of water-soluble forms of metals, the evaluation of the acute toxicity of waste after oral administration to mice and rats, the study of the toxicity of waste by biotesting and the activity of natural radionuclides. The slag crushed stone virtually lacks water-soluble elements when it contains a high level of bulk forms of metals. According to acute toxicity for warm-blooded animals, the slag crushed stone belongs to Hazard Class IV by GOST 12.1.007-76 (low hazard substances). The biotesting on hydrocoles, the slag crushed stone is also referred to as Class IV (low hazard substances). In terms of the level of natural radionuclides, the slag crushed stone poses no hazard to the environment. The performed studies give grounds to recommend metallurgical slag crushed stone to be added to natural materials for highway building.

Effect of high hydrogen content on metallurgical and mechanical properties of zirconium alloy claddings after heat-treatment at high temperature

International Nuclear Information System (INIS)

Turque, Isabelle

2016-01-01

Under hypothetical loss-of-coolant accident conditions, fuel cladding tubes made of zirconium alloys can be exposed to steam at high temperature (HT, up 1200 C) before being cooled and then quenched in water. In some conditions, after burst occurrence the cladding can rapidly absorb a significant amount of hydrogen (secondary hydriding), up to 3000 wt.ppm locally, during steam exposition at HT. The study deals with the effect, poorly studied up to date, of high contents of hydrogen on the metallurgical and mechanical properties of two zirconium alloys, Zircaloy-4 and M5, during and after cooling from high temperatures, at which zirconium is in its β phase. A specific facility was developed to homogeneously charge in hydrogen up to ∼ 3000 wt.ppm cladding tube samples of several centimeters in length. Phase transformations, chemical element partitioning and hydrogen precipitation during cooling from the β temperature domain of zirconium were studied by using several techniques, for the materials containing up to ∼ 3000 wt.ppm of hydrogen in average: in-situ neutron diffraction upon cooling from 700 C, X-ray diffraction, μ-ERDA, EPMA and electron microscopy in particular. The results were compared to thermodynamic predictions. In order to study the effect of high hydrogen contents on the mechanical behavior of the (prior-)μ phase of zirconium, axial tensile tests were performed at various temperatures between 20 and 700 C upon cooling from the β temperature domain, on samples with mean hydrogen contents up to ∼ 3000 wt.ppm. The results show that metallurgical and mechanical properties of the (prior-)β phase of zirconium alloys strongly depend on temperature and hydrogen content. (author) [fr

Study on the effect of heat treatment and gasification on the carbon structure of coal chars and metallurgical cokes using fourier transform Raman spectroscopy

Energy Technology Data Exchange (ETDEWEB)

S. Dong; P. Alvarez; N. Paterson; D.R. Dugwell; R. Kandiyoti [Imperial College London, London (United Kingdom). Department of Chemical Engineering

2009-03-15

Differences in the development of carbon structures between coal chars and metallurgical cokes during high-temperature reactions have been investigated using Raman spectroscopy. These are important to differentiate between different types of carbons in dust recovered from the top gas of the blast furnace. Coal chars have been prepared from a typical injectant coal under different heat-treatment conditions. These chars reflected the effect of peak temperature, residence time at peak temperature, heating rate and pressure on the evolution of their carbon structures. The independent effect of gasification on the development of the carbon structure of a representative coal char has also been studied. A similar investigation has also been carried out to study the effect of heat-treatment temperature (from 1300 to 2000{sup o}C) and gasification on the carbon structure of a typical metallurgical coke. Two Raman spectral parameters, the intensity ratio of the D band to the G band (I{sub D}/I{sub G}) and the intensity ratio of the valley between D and G bands to the G band (I{sub V}/I{sub G}), have been found useful in assessing changes in carbon structure. An increase in I{sub D}/I{sub G} indicates the growth of basic graphene structural units across the temperature range studied. A decrease in I{sub V}/I{sub G} appears to suggest the elimination of amorphous carbonaceous materials and ordering of the overall carbon structure. The Raman spectral differences observed between coal chars and metallurgical cokes are considered to result from the difference in the time-temperature history between the raw injectant coal and the metallurgical coke and may lay the basis for differentiation between metallurgical coke fines and coal char residues present in the dust carried over the top of the blast furnace. 41 refs., 17 figs., 3 tabs.

On sexual behavior and sex-role reversal

NARCIS (Netherlands)

Schuiling, GA

Sex is not about reproduction; sex is about (re-) combination of DNA. Sex, not reproduction, always involves physical contact between two individuals; to achieve this, strategies of sexual behavior evolved. Sexual behavior, therefore, did not evolve as part of a reproductive strategy, but evolved to

Selection of human capital in metallurgical companies using information technology (IT

Directory of Open Access Journals (Sweden)

I. Iancu

2013-10-01

Full Text Available Personnel selection is a process that takes place in a company in order to have better business performance and competitive advantage. Nowadays, companies have realized the importance of human capital as a necessity for survival in today’s competitive market. There are several methods for selecting staff, but this paper seeks to demonstrate that this selection can be done with the help of an expert system. Metallurgical companies face even greater challenges for managing personnel selection. This research will discover and test the key elements of management personnel selection and implementation of an expert system.

Evolvable synthetic neural system

Science.gov (United States)

Curtis, Steven A. (Inventor)

2009-01-01

An evolvable synthetic neural system includes an evolvable neural interface operably coupled to at least one neural basis function. Each neural basis function includes an evolvable neural interface operably coupled to a heuristic neural system to perform high-level functions and an autonomic neural system to perform low-level functions. In some embodiments, the evolvable synthetic neural system is operably coupled to one or more evolvable synthetic neural systems in a hierarchy.

Powder metallurgical high performance materials. Proceedings. Volume 4: late papers

Energy Technology Data Exchange (ETDEWEB)

Kneringer, G; Roedhammer, P; Wildner, H [eds.

2001-07-01

This is the fourth volume (late papers) of the 15th International Plansee seminar 2001 which general theme was 'Powder metallurgical high performance materials'. The seminar looked beyond the refractory metals and cemented carbides, which remain as its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. This volume 4 contains papers dealing with high performance P/M metals (ITER and fusion reactors, solid targets, materials microstructure, novel alloys, etc.), P/M hard materials ( production and characterization, tungsten carbides, titanium carbides, microstructural design, coatings composition and performance, etc.) and general topics. From 37 papers 24 correspond to INIS subject scope and they were indexed separately. (nevyjel)

Characterization of Nanocarbon Copper Composites Manufactured in Metallurgical Synthesis Process

Science.gov (United States)

Knych, Tadeusz; Kwaśniewski, Paweł; Kiesiewicz, Grzegorz; Mamala, Andrzej; Kawecki, Artur; Smyrak, Beata

2014-08-01

Currently, there is a worldwide search for new forms of materials with properties that are significantly improved in comparison to materials currently in use. One promising research direction lies in the synthesis of metals containing modern carbon materials ( e.g., graphene, nanotubes). In this article, the research results of metallurgical synthesis of a mixture of copper and two different kinds of carbon (activated carbon and multiwall carbon nanotubes) are shown. Samples of copper-carbon nanocomposite were synthesized by simultaneously exposing molten copper to an electrical current while vigorously stirring and adding carbon while under an inert gas atmosphere. The article contains research results of density, hardness, electrical conductivity, structure (TEM), and carbon decomposition (SIMS method) for the obtained materials.

Powder metallurgical high performance materials. Proceedings. Volume 4: late papers

International Nuclear Information System (INIS)

Kneringer, G.; Roedhammer, P.; Wildner, H.

2001-01-01

This is the fourth volume (late papers) of the 15th International Plansee seminar 2001 which general theme was 'Powder metallurgical high performance materials'. The seminar looked beyond the refractory metals and cemented carbides, which remain as its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. This volume 4 contains papers dealing with high performance P/M metals (ITER and fusion reactors, solid targets, materials microstructure, novel alloys, etc.), P/M hard materials ( production and characterization, tungsten carbides, titanium carbides, microstructural design, coatings composition and performance, etc.) and general topics. From 37 papers 24 correspond to INIS subject scope and they were indexed separately. (nevyjel)

Optimization Review: Bunker Hill Mining and Metallurgical Complex Superfund Site, Central Treatment Plant (CTP), Kellogg, Shoshone County, Idaho

Science.gov (United States)

The Bunker Hill Mining and Metallurgical Complex Superfund Site includes all areas of the Coeur d’Alene Basin where mining-related contamination occurred and encompasses a 21-square mile “Box” along Interstate 90 surrounding the former smelter complex.

THE MODELS OF THE MANAGEMENT OPTIMIZATION OF THE ORGANIZATIONAL STRUCTURES OF RUP “BELORUSSIAN METALLURGICAL WORKS”

Directory of Open Access Journals (Sweden)

A. N. Chichko

2006-01-01

Full Text Available The new approach to the mathematic modeling and optimization of interrelation of the control units of the metallurgical enterprise organizational structures is offered. The mathematical model of the organizational structure based on temporary characteristics of control units loading is offered at the example of one of the organizational structures BMZ.

Cryogenic treatment of steel: from concept to metallurgical understanding

DEFF Research Database (Denmark)

Villa, Matteo; Somers, Marcel A. J.

2017-01-01

, the metallurgical understanding of the microstructural changes involved in cryogenic treatment of steel has remained poor. It is believed that the improvement in wear resistance is promoted by an enhanced precipitation of carbides during tempering, but no explanation has been given as to how this enhanced......Subjecting steel to cryogenic treatment to improve its properties was conceived in the 30ies of the previous century. The proof of concept that properties, in particular wear resistance, can indeed be improved importantly, was reported in the next decades. Despite many investigations...... precipitation can be obtained. In the last six years, the authors have applied in situ magnetometry, synchrotron X-Ray Diffraction and dilatometry to enlighten the phase transitions occurring in steels at cryogenic temperatures and to point out the connection between different treatment parameters...

FINDING WAYS OF RECYCLING DUST OF ARC STEEL FURNACES AT THE BELARUSIAN METALLURGIC PLANT

Directory of Open Access Journals (Sweden)

A. V. Demin

2015-01-01

Full Text Available The first part examines the theoretical possibility of recycling dust of arc steel furnaces. The different modes of dust disposal depending on the task of recycling are discussed: recycling at minimal cost; recycling with a maximum extraction of iron; recycling with maximum extraction of zinc. The results of laboratory studies providing information on the technical feasibility of recycling dust formed at the Belarusian metallurgic plant are provided.

Investigations for decision making on an old tailing pond of a former experimental metallurgical plant

International Nuclear Information System (INIS)

Razikov, Z.A.; Pavljuk, L.M.; Bezzubov, N.I.

2002-01-01

Investigations are described on an abandoned tailing pond of a former experimental metallurgical plant which operated during the period 1945-1950. The aim of these investigations was to explore radiological hazards arising from the tailing pond for the population and to obtain data for decision making on redeployment or dumping of the pond. Methods used, results obtained and conclusions drawn are outlined. (author)

Metallurgical Laboratory Hazardous Waste Management Facility groundwater monitoring report: Third quarter 1993

International Nuclear Information System (INIS)

1993-12-01

During third quarter 1993, samples from AMB groundwater monitoring wells at the Metallurgical Laboratory Hazardous Waste Management Facility were analyzed for certain heavy metals, indicator parameters, radionuclides, volatile organic compounds, and other constituents. Eight parameters exceeded standards during the quarter. As in previous quarters, tetrachloroethylene and trichloroethylene exceeded final Primary Drinking Water Standards; and aluminum, iron, lead, manganese, pH, and total organic halogens exceeded the Savannah River Site Flag 2 criteria in one or more of the wells. Groundwater flow direction and rate in the water-table unit were similar to previous quarters

Metallurgical source-contribution analysis of PM10 annual average concentration: A dispersion modeling approach in moravian-silesian region

Directory of Open Access Journals (Sweden)

P. Jančík

2013-10-01

Full Text Available The goal of the article is to present analysis of metallurgical industry contribution to annual average PM10 concentrations in Moravian-Silesian based on means of the air pollution modelling in accord with the Czech reference methodology SYMOS´97.

Disordered gambling: the evolving concept of behavioral addiction

Science.gov (United States)

Clark, Luke

2014-01-01

The reclassification of gambling disorder within the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5) addictions category marks an important step for addiction science. The similarities between gambling disorder and the substance use disorders have been well documented. As gambling is unlikely to exert actively damaging effects on the brain, the cognitive sequelae of gambling disorder may provide insights into addictive vulnerabilities; this idea is critically evaluated in light of recent structural imaging data. The second part of the review analyzes a fundamental question of how a behavior can become addictive in the absence of exogenous drug stimulation. The relative potency of drug and nondrug rewards is considered, alongside evidence that cognitive distortions in the processing of chance (for example, the illusion of control and the gambler's fallacy) may constitute an important added ingredient in gambling. Further understanding of these mechanisms at neural and behavioral levels will be critical for the classification of future behavioral addictions, and I consider the current research data for obesity and binge eating, compulsive shopping, and internet gaming disorder. PMID:25336388

Development of advanced high strength tantalum base alloys. Phase 3: Influence of metallurgical condition on the mechanical properties of ASTAR-811C sheet

Science.gov (United States)

Ammon, R. L.; Buckman, R. W., Jr.; Harrod, D. L.

1972-01-01

Metallurgical condition was shown to have a significant effect on the creep properties of ASTAR-811C (Ta-8W-1Re-0.7Hf-0.025C) sheet. Cold worked material exhibited creep rates 30 times higher than solution annealed material and 10 times greater than for recrystallized material. Both grain size and the carbide morphology changes as the final annealing temperature was raised from 3000 F to 3600 F. However, the lowest creep rates were achieved for material which retained the high temperature form of the Ta2C precipitate. Samples with GTA weldments had essentially identical properties as recrystallized base metal. Cooling rates from 3600 F of 5, 50, and 800 F deg/min. had little effect on the 2000 and 2400 F creep behavior of ASTAR-811C.

THE PROFITABILITY AND LIQUIDITY UNDER THE INFLUENCE OF THE FINANCING POLICY IN THE METALLURGICAL INDUSTRY OF EU 28

Directory of Open Access Journals (Sweden)

DOBROTĂ GABRIELA

2014-12-01

Full Text Available In the context of the problems of the economic system, the use of the capital and his structure represent important elements in the process of the financial decisions. The aim of this paper is to identify the influence of funding policy on rentability in metallurgical industry, dimensioned with the help of a set of relevant indicators, determined on the base of some aggregated data for a significant sample of very large firms from EU 28. Also, the paper present the situation of liquidity, reflected through the cash- flow and liquidity ratio, in the metallurgical industry of EU 28, being used dates for the period 2004 – 2013, for the mentioned sample. The conclusion of the realised study is that a funding policy well-founded, correlated with the efficient management of expenses and proactive risk management can positively influence the profitability and liquidity.

Electrochemical and metallurgical characterization of ZrCr{sub 1-x}NiMo{sub x} AB{sub 2} metal hydride alloys

Energy Technology Data Exchange (ETDEWEB)

Erika, Teliz [Universidad de la República, Facultad de Ciencias, Laboratorio de Electroquímica Fundamental, Núcleo Interdisciplinario Ingeniería Electroquímica, Igua 4225, CP 11400 Montevideo (Uruguay); Ricardo, Faccio [Universidad de la República, Crystallography, Solid State and Materials Laboratory (Cryssmat-Lab), DETEMA, Centro NanoMat, Polo Tecnológico de Pando, Espacio Interdisciplinario, Facultad de Química, Montevideo (Uruguay); Fabricio, Ruiz [Consejo Nacional de Investigaciones Científicas y Técnicas , CONICET, Av. Rivadavia 1917, C1033AAJ Ciudad de Buenos Aires (Argentina); Centro Atómico Bariloche , Comisión Nacional de Energía Atómica (CAB-CNEA), Av. Bustillo 9500, CP 8400 S.C. de Bariloche, RN (Argentina); Fernando, Zinola [Universidad de la República, Facultad de Ciencias, Laboratorio de Electroquímica Fundamental, Núcleo Interdisciplinario Ingeniería Electroquímica, Igua 4225, CP 11400 Montevideo (Uruguay); and others

2015-11-15

The effects of partial replacement of chromium by molybdenum was studied on the structure and electrochemical kinetic properties of ZrCr{sub 1-x}NiMo{sub x}(x = 0.0, 0.3 and 0.6) metal hydride alloys. The arc-melting prepared alloys were metallurgically characterized by X-ray diffraction and energy dispersive spectroscopy microanalysis, which showed AB{sub 2} (with hexagonal C14 structure) and Zr{sub x}Ni{sub y} (Zr{sub 7}Ni{sub 10}, Zr{sub 9}Ni{sub 11}) phases. After a partial substitution of chromium by molybdenum, secondary phases monotonically increase with the C14 unit cell volume indicating that most of molybdenum atoms locate in the B-site. The alloys were electrochemically characterized using charge/discharge cycling, electrochemical impedance spectroscopy and rate capability experiments that allowed the determination of hydriding reaction kinetic parameters. The presence of molybdenum produces a positive effect for hydrogen diffusion in the alloy lattice, and ZrCr{sub 0.7}NiMo{sub 0.3} alloy depicts the better kinetics associated with a fast activation, lower charge transfer resistance and the best high rate discharge behavior. This fact would be related to a lower diffusion time constant and a bigger value of the product between exchange density current and surface active area. There is a trade-off in the amounts of secondary phase and Laves phases in order to improve the kinetic performance. - Highlights: • Metallurgical characterization evidences the presence of Zr{sub x}Ni{sub y} and C14 phases. • The partial replacement of Cr by Mo promotes the segregation of Zr{sub x}Ni{sub y} phase. • The incorporation of molybdenum improves the kinetics for the hydriding process. • Mo produces a decrease in the diffusion time constant.

Evaluation of powder metallurgical processing routes for multi-component niobium silicide-based high-temperature alloys

Energy Technology Data Exchange (ETDEWEB)

Seemueller, Hans Christoph Maximilian

2016-03-22

Niobium silicide-based composites are potential candidates to replace nickel-base superalloys for turbine applications. The goal of this work was to evaluate the feasibility and differences in ensuing properties of various powder metallurgical processing techniques that are capable of manufacturing net-shape turbine components. Two routes for powder production, mechanical alloying and gas atomization were combined with compaction via hot isostatic pressing and powder injection molding.

The identification of zones of amplification of disruptions in network supply chains of metallurgic products

Directory of Open Access Journals (Sweden)

M. Kramarz

2015-01-01

Full Text Available An increase in the number of participants in a supply chain and network relations results in an increase in the complexity of the entire logistic and production system. Consequently, there appear additional potential sources of disruptions in material flows. The aim of the research presented in the article is to identify the zones of amplification of disruptions in network supply chains of metallurgic products.

Fast determination of impurities in metallurgical grade silicon for photovoltaics by instrumental neutron activation analysis

International Nuclear Information System (INIS)

Hampel, J.; Boldt, F.M.; Gerstenberg, H.; Hampel, G.; Kratz, J.V.; Reber, S.; Wiehl, N.

2011-01-01

Standard wafer solar cells are made of near-semiconductor quality silicon. This high quality material makes up a significant part of the total costs of a solar module. Therefore, new concepts with less expensive so called solar grade silicon directly based on physiochemically upgraded metallurgical grade silicon are investigated. Metallurgical grade silicon contains large amounts of impurities, mainly transition metals like Fe, Cr, Mn, and Co, which degrade the minority carrier lifetime and thus the solar cell efficiency. A major reduction of the transition metal content occurs during the unidirectional crystallization due to the low segregation coefficient between the solid and liquid phase. A further reduction of the impurity level has to be done by gettering procedures applied to the silicon wafers. The efficiency of such cleaning procedures of metallurgical grade silicon is studied by instrumental neutron activation analysis (INAA). Small sized silicon wafers of approximately 200 mg with and without gettering step were analyzed. To accelerate the detection of transition metals in a crystallized silicon ingot, experiments of scanning whole vertical silicon columns with a diameter of approximately 1 cm by gamma spectroscopy were carried out. It was demonstrated that impurity profiles can be obtained in a comparably short time. Relatively constant transition metal ratios were found throughout an entire silicon ingot. This led to the conclusion that the determination of several metal profiles might be possible by the detection of only one 'leading element'. As the determination of Mn in silicon can be done quite fast compared to elements like Fe, Cr, and Co, it could be used as a rough marker for the overall metal concentration level. Thus, a fast way to determine impurities in photovoltaic silicon material is demonstrated. - Highlights: → We demonstrate a fast way to determine impurities in photovoltaic silicon by NAA. → We make first experiments of locally

3-D Modelling of Electromagnetic, Thermal, Mechanical and Metallurgical Couplings in Metal Forming Processes

International Nuclear Information System (INIS)

Chenot, Jean-Loup; Bay, Francois

2007-01-01

The different stages of metal forming processes often involve - beyond the mechanical deformations processes - other physical coupled problems, such as heat transfer, electromagnetism or metallurgy. The purpose of this paper is to focus on problems involving electromagnetic couplings. After a brief recall on electromagnetic modeling, we shall then focus on induction heating processes and present some results regarding heat transfer, as well as mechanical couplings. A case showing coupling for metallurgic microstructure evolution will conclude this paper

Trading Control Intelligence for Physical Intelligence: Muscle Drives in Evolved Virtual Creatures

DEFF Research Database (Denmark)

Lessin, Dan; Fussell, Don; Miikkulainen, Risto

2014-01-01

Traditional evolved virtual creatures [12] are actuated using unevolved, uniform, invisible drives at joints between rigid segments. In contrast, this paper shows how such conven- tional actuators can be replaced by evolvable muscle drives that are a part of the creature’s physical structure....... This design is important for two reasons: First, the con- trol intelligence is made visible in the purposeful develop- ment of muscle density, orientation, attachment points, and size. Second, the complexity that needs to be evolved for the brain to control the actuators is reduced, and in some cases can...... be essentially eliminated, thus freeing brain power for higher-level functions. Such designs may thus make it pos- sible to create more complex behavior than would otherwise be achievable....

Occupational exposure in South African metallurgical plants and industries involving naturally occurring radionuclides

International Nuclear Information System (INIS)

Kruger, I.D.

2002-01-01

South Africa has a very large mining and minerals processing industry exploiting a variety of ores and minerals containing elevated levels of NORM. The industry employs more than 300,000 persons. Doses have been assessed to workers in the mining industry in South Africa. In the gold mining industry radon measurements have been performed since the early 1970s. Regulations have been in force since 1990. The mean annual dose to underground gold mine workers, mostly from radon progeny, is about 5 mSv with maximum doses exceeding 20 mSv. The maximum annual dose to surface workers in gold mines is 5 mSv. In South African coal mines the mean annual dose from inhalation of radon decay products has been estimated from limited radon concentration measurements to be about 0.6 mSv. In the phosphoric acid and fertilizer production industry the doses to the workers do not exceed 6 mSv/y. There are 3 mineral sands operations in South Africa, for which the maximum annual dose to workers is 3 mSv. One open pit copper mine contains elevated levels of U, which is extracted as a by-product. The maximum annual doses to workers are 5 mSv for workers in the mine and 20 mSv for workers in the metallurgical plant. Worker doses in the metallurgical plant have since been reduced with the introduction of radiation protection measures

Study of ecologo-biological reactions of common flax to finely dispersed metallurgical wastes

Science.gov (United States)

Zakharova, O.; Gusev, A.; Skripnikova, E.; Skripnikova, M.; Krutyakov, Yu; Kudrinsky, A.; Mikhailov, I.; Senatova, S.; Chuprunov, C.; Kuznetsov, D.

2015-11-01

Study was carried out on the influence of metallurgic industrial sludge on morphometric and biochemical indicators as well as productivity of common flax under laboratory and field conditions. In laboratory settings negative influence on seed germinating ability and positive influence on sprouts biomass production in water medium were observed. In sand medium suppression of biological productivity under the influence of sludge together with photosynthetic system II (FS II) activity stimulation were registered. Biochemical study showed peroxidase activity decrease in laboratory, while activity of polyphenol oxidase, superoxide dismutase and catalase were given a mild boost under the influence of sludge. In the field trial, positive influence of sludge on flax photosynthetic apparatus was shown. Positive influence of sludge on vegetation and yield indicators was observed. The analysis of heavy metals content showed excess over maximum allowable concentration (MAC) of copper and zinc in control plants, it may point to the background soil pollution. In the plants from the trial groups receiving 0.5 and 2 ton/ha heavy metals content below the control values was registered. Application of 4 ton/ha led to the maximum content of copper and zinc in the plants among the trial groups. The analysis of soils from the test plots indicated no excess over maximum allowable concentrations of heavy metals. Thus, further study of possibilities of using metallurgic industrial sludge as a soil stimulator in flax cultivation at the application rate of 0.5 t/ha seems promising.

Application of Six Sigma Using DMAIC Methodology in the Process of Product Quality Control in Metallurgical Operation

Directory of Open Access Journals (Sweden)

Girmanová Lenka

2017-12-01

Full Text Available The Six Sigma DMAIC can be considered a guide for problem solving and product or process improvement. The majority of companies start to implement Six Sigma using the DMAIC methodology. The paper deals with application of Six Sigma using the DMAIC methodology in the process of product quality control. The case study is oriented on the field of metallurgical operations. The goal of the Six Sigma project was to ensure the required metallurgic product quality and to avoid an increase in internal costs associated with poor product quality. In this case study, a variety of tools and techniques like flow chart, histogram, Pareto diagram, analysis of FMEA (Failure Mode and Effect Analysis data, cause and effect diagram, logical analysis was used. The Sigma level has improved by approximately 13%. The achieved improvements have helped to reduce the quantity of defective products and the processing costs (technology for re-adjusting. Benefits resulting from the DMAIC implementation can be divided into three levels: the qualitative, economic and safety level.

Determining sulfur in metallurgical coke by the X-ray fluorescent method

Energy Technology Data Exchange (ETDEWEB)

Sofilic, T.; Kesic-Racan, M.; Sindler, M.; Sokolean, D.

1979-01-01

A method is described of X-ray fluorescent analysis for current determination of sulfur in the concentration range of 0.5-1.16% in metallurgical coke. To do this, the analyzed material (coke) is ground to a particle size of 200 mu and mixed in a 1:1 ratio with an organic binder (soluble starch). The mixture is briquetted in meshes of a certain size under a pressure of 25 tons/cm/sub 2/. The tablets obtained are analyzed in a Phillips spectrometer with a Cr anticathode. The presence is noted of a linear dependence between the S content and the instrument reading; the correlation factor is 0.91; the mean detection error, 0.0596.

Utilizing of the metallurgical slag for production of cementless concrete mixtures

Directory of Open Access Journals (Sweden)

D. Baricová

2012-10-01

Full Text Available In process of pig iron, steel and cast iron production besides main product, also secondary products are formed, that have character of secondary raw materials and industrial wastes. The most abundant secondary product originating in the metallurgical process is furnace slag. Total amount of accured slag, also its chemical, mineralogical, physical – chemical properties and similarity with natural stones predestinate its utilisation in different fields of industry. The contribution deals with production of cementless concrete mixtures, where the main parts were formed by blast furnace granulated slag grinded and different gravel slag from blast furnace, oxygen converter and electric arc furnace. As activators of solidification different kinds of water glass were tested.

Integrated Multimotor Electrical DC Drive for Metallurgical Rolling Table

Directory of Open Access Journals (Sweden)

Gała Marek

2015-06-01

Full Text Available A drive system of a section of a metallurgical rolling table consisting of six dc motors, 2220 amperes of total current, fed from a single ABB reversible thyristor converter has been described in this paper. Autonomous excitation circuits of the motors are fed from independent thyristor converters working in the so called MULTIFEX system linked with a supervisory high power converter. There are presented schemes of the DSL communication realized by FEX excitation cards of the motors using the SDSC card of the DCS-800-S02 converter and logic control system based on a PLC controller. The parameterization of the DCS-800 converter and the DCF 803 excitation systems was conducted using the DriveWindow software tool. Significant waveforms of voltages, currents and the estimated motor velocity are described and presented for the idle run as well as during transporting sheets discharged from a pusher furnace.

Silver recovery from zinc metallurgical sludge – analysis of solutions

Directory of Open Access Journals (Sweden)

Pietrzyk Stanisław

2017-01-01

Full Text Available During the hydrometallurgical process of zinc production, conducted in the ZGH “Bolesław” S.A. in Bukowno [Mine and Metallurgical Plant], about 40,000 tons of sludge is generated. After dehydration in the Larox filter presses, sludge contains ca. 16-18% of Zn, 20-25% of Fe, and 200-300 ppm of Ag. Next, sludge is transported to the Olkusz concentrator for flotation to obtain concentrate enriched with Ag (1,000-1,500 ppm. The concentrate is then sent to the HC “Miasteczko Śląskie” [zinc smelter], while the flotation tailings are subjected to recycling in waelz kiln in Bukowno to regain mainly Zn and Pb, in the form of oxides (also sent later to the HC “Miasteczko Śląskie”.

Ti₃SiC₂ Synthesis by Powder Metallurgical Methods

OpenAIRE

Kero, Ida; Antti, Marta-Lena; Odén, Magnus

2007-01-01

Titanium silicon carbide MAX phase was synthesised by a powder metallurgical method from ball milled TiC/Si powders of two different compositions, with TiC/Si ratios of 3:2 and 3:2.2 respectively. The cold pressed samples were analysed by dilatometry under flowing argon or sintered under vacuum for different times. The sintered samples were evaluated using x-ray diffraction (XRD). This study showed that titanium carbide was always present as a secondary phase and silicon carbide accompanied t...

Production of metallurgical cokes from some Turkish lignites using sulphite liquor binders

Energy Technology Data Exchange (ETDEWEB)

Yanik, J.; Saglam, M.; Yuksel, M. (Ege University, Izmir (Turkey). Dept. of Chemistry)

1990-04-01

Soma and Tuncbilek lignites were briquetted at 80{degree}C under 0-100 MPa, using varying amounts of sulphite liquor binders. The briquettes were then carbonized at 950{degree}C, and the resulting formed cokes were examined. The effects of the type and concentration of binders, and of the briquetting pressure, on the strength and porosity of the formcokes were investigated. As a result of these experiments, optimal briquetting conditions were established. It was also stated that formcokes made from both Turkish lignite samples under optimal briquetting conditions could be used for metallurgical purposes, particularly in non-ferrous metallurgy. 17 refs., 1 fig., 4 tabs.

Low drift type N thermocouples in out-of-pile advanced gas reactor mock-up test: metallurgical analysis

International Nuclear Information System (INIS)

Scervini, M.; Palmer, J.; Haggard, D.C.; Swank, W.D.

2015-01-01

Thermocouples are the most commonly used sensors for temperature measurement in nuclear reactors. They are crucial for the control of current nuclear reactors and for the development of GEN IV reactors. In nuclear applications thermocouples are strongly affected by intense neutron fluxes. As a result of the interaction with neutrons, the thermoelements of the thermocouples undergo transmutation, which produces a time dependent change in composition and, as a consequence, a time dependent drift of the thermocouple signal. Thermocouple drift can be very significant for in-pile temperature measurements and may render the temperature sensors unreliable after exposure to nuclear radiation for relatively short times compared to the life required for temperature sensors in nuclear applications. Previous experiences with type K thermocouples in nuclear reactors have shown that they are affected by neutron irradiation only to a limited extent. Similarly type N thermocouples are expected to be only slightly affected by neutron fluxes. Currently the use of Nickel based thermocouples is limited to temperatures lower than 1000 deg. C due to drift related to phenomena other than nuclear irradiation. As part of a collaboration between Idaho National Laboratory (INL) and the University of Cambridge a variety of Type N thermocouples have been exposed at INL in an Advanced Gas Reactor mock-up test at 1150 deg. C for 2000 h, 1200 deg. C for 2000 h, 125 deg. C for 200 h and 1300 deg. C for 200 h, and later analysed metallurgically at the University of Cambridge. The use of electron microscopy allows to identify the metallurgical changes occurring in the thermocouples during high temperature exposure and correlate the time dependent thermocouple drift with the microscopic changes experienced by the thermoelements of different thermocouple designs. In this paper conventional Inconel 600 sheathed type N thermocouples and a type N using a customized sheath developed at the University of

Low drift type N thermocouples in out-of-pile advanced gas reactor mock-up test: metallurgical analysis

Energy Technology Data Exchange (ETDEWEB)

Scervini, M. [University of Cambridge, Department of Materials Science and Metallurgy, 27 Charles Babbage Road, CB30FS Cambridge, (United Kingdom); Palmer, J.; Haggard, D.C.; Swank, W.D. [Idaho National Laboratory, Idaho Falls, ID 83415-3840, (United States)

2015-07-01

Thermocouples are the most commonly used sensors for temperature measurement in nuclear reactors. They are crucial for the control of current nuclear reactors and for the development of GEN IV reactors. In nuclear applications thermocouples are strongly affected by intense neutron fluxes. As a result of the interaction with neutrons, the thermoelements of the thermocouples undergo transmutation, which produces a time dependent change in composition and, as a consequence, a time dependent drift of the thermocouple signal. Thermocouple drift can be very significant for in-pile temperature measurements and may render the temperature sensors unreliable after exposure to nuclear radiation for relatively short times compared to the life required for temperature sensors in nuclear applications. Previous experiences with type K thermocouples in nuclear reactors have shown that they are affected by neutron irradiation only to a limited extent. Similarly type N thermocouples are expected to be only slightly affected by neutron fluxes. Currently the use of Nickel based thermocouples is limited to temperatures lower than 1000 deg. C due to drift related to phenomena other than nuclear irradiation. As part of a collaboration between Idaho National Laboratory (INL) and the University of Cambridge a variety of Type N thermocouples have been exposed at INL in an Advanced Gas Reactor mock-up test at 1150 deg. C for 2000 h, 1200 deg. C for 2000 h, 125 deg. C for 200 h and 1300 deg. C for 200 h, and later analysed metallurgically at the University of Cambridge. The use of electron microscopy allows to identify the metallurgical changes occurring in the thermocouples during high temperature exposure and correlate the time dependent thermocouple drift with the microscopic changes experienced by the thermoelements of different thermocouple designs. In this paper conventional Inconel 600 sheathed type N thermocouples and a type N using a customized sheath developed at the University of

Production of highly porous glass-ceramics from metallurgical slag, fly ash and waste glass

OpenAIRE

Mangutova Bianka V.; Fidancevska Emilija M.; Milosevski Milosav I.; Bossert Joerg H.

2004-01-01

Glass-ceramics composites were produced based on fly-ash obtained from coal power stations, metallurgical slag from ferronickel industry and waste glass from TV monitors, windows and flasks. Using 50% waste flask glass in combination with fly ash and 20% waste glass from TV screens in combination with slag, E-modulus and bending strength values of the designed systems are increased (system based on fly ash: E-modulus from 6 to 29 GPa, and bending strength from 9 to 75 MPa). The polyurethane f...

3D Model Studies on the Effect of Bed and Powder Type Upon Radial Static Pressure and Powder Distribution in Metallurgical Shaft Furnaces

Directory of Open Access Journals (Sweden)

Panic B.

2017-09-01

Full Text Available The flow of gases in metallurgical shaft furnaces has a decisive influence on the course and process efficiency. Radial changes in porosity of the bed cause uneven flow of gas along the radius of the reactor, which sometimes is deliberate and intentional. However, holdup of solid particles in descending packed beds of metallurgical shaft furnaces can lead to unintentional changes in porosity of the bed along the radial reactor. Unintentional changes in porosity often disrupt the flow of gas causing poor performance of the furnace. Such disruptions of flow may occur in the blast furnace due to high level of powder content in gas caused by large amount of coal dust/powder insufflated as fuel substitute. The paper describes the model test results of radial distribution of static pressure and powder hold up within metallurgical reactor. The measurements were carried out with the use of 3D physical model of two-phase flow gas-powder in the moving (descending packed bed. Sinter or blast furnace pellets were used as packed bed while carbon powder or iron powder were used as the powder. Wide diversity within both static pressure distribution and powder distribution along the radius of the reactor were observed once the change in the type of powder occurred.

Inventory management in a metallurgical of the automotive industry

Directory of Open Access Journals (Sweden)

Marcos Antonio Maia de Oliveira

2015-12-01

Full Text Available This article aims to analyze the importance of inventory management in a metallurgical company, located in Santo André city, in Grande São Paulo, since the inventory management is crucial within a company that wants to survive nowadays, by studying the main features and trends in the methods used for inventory control. In this case study the basic concepts for good control were considered, showing tools currently used in the market, providing data for material purchase, sales control, parts in stock, future orders, MRP, storage space, among others once many companies have high and unnecessary cost of stock for not being aware of the real importance of this control. It is felt that the logistics of the company should invest in technology by purchasing the MRP system, visiting fairs and attending seminars. This way, the company will have better inventory control thus consequently decrease the purchase of materials.

Arsenic precipitation from metallurgical effluents; Precipitacion de arsenico desde efluentes metalurgicos

Energy Technology Data Exchange (ETDEWEB)

Navarro, P.; Vargas, C.; Araya, E.; Martin, I.; Alguacil, F. J.

2004-07-01

In the mining-metallurgical companies different liquid effluents are produced, which can contain a series of dissolved elements that are considered dangerous from an environmental point of view. One of these elements is the arsenic, especially in the state of oxidation +5 that can be precipitated as calcium or iron arsenate. To fulfil the environmental requests it should have in solution a content of arsenic lower than 0,5 mg/l and the obtained solid product should be very stable under the condition in which it will be stored. this work looks for the best conditions of arsenic precipitation, until achieving contents in solution lower than such mentioned concentration. Also, the stability of the precipitates was studied. (Author) 7 refs.

Historical Review of the Correlation of Ballistic and Metallurgical Characteristics of Domestic Armor at Watertown Arsenal

Science.gov (United States)

1945-12-07

really under- stood. It was learned, then that pearlitic and bainitic microstructures imparted poor impact toughness to steels , pearlitic structures...having a more detrimental effect than bainitic structures, and that a steel could show little or no free ferrite and still pofssess poor shock resistance...arsenal for metallurgical study. The studies at the arsenal revealed that presence of bainitic structures in the core of low alloy NS type steels

Do motifs reflect evolved function?--No convergent evolution of genetic regulatory network subgraph topologies.

Science.gov (United States)

Knabe, Johannes F; Nehaniv, Chrystopher L; Schilstra, Maria J

2008-01-01

Methods that analyse the topological structure of networks have recently become quite popular. Whether motifs (subgraph patterns that occur more often than in randomized networks) have specific functions as elementary computational circuits has been cause for debate. As the question is difficult to resolve with currently available biological data, we approach the issue using networks that abstractly model natural genetic regulatory networks (GRNs) which are evolved to show dynamical behaviors. Specifically one group of networks was evolved to be capable of exhibiting two different behaviors ("differentiation") in contrast to a group with a single target behavior. In both groups we find motif distribution differences within the groups to be larger than differences between them, indicating that evolutionary niches (target functions) do not necessarily mold network structure uniquely. These results show that variability operators can have a stronger influence on network topologies than selection pressures, especially when many topologies can create similar dynamics. Moreover, analysis of motif functional relevance by lesioning did not suggest that motifs were of greater importance to the functioning of the network than arbitrary subgraph patterns. Only when drastically restricting network size, so that one motif corresponds to a whole functionally evolved network, was preference for particular connection patterns found. This suggests that in non-restricted, bigger networks, entanglement with the rest of the network hinders topological subgraph analysis.

Powder metallurgical processing of magnetostrictive materials based on rare earth-iron intermetallic compounds

International Nuclear Information System (INIS)

Malekzadeh, M.

1978-01-01

Procedures are described for fabrication of high density rare earth-iron magnetostrictive compounds by powder metallurgical techniques. The fabrication involves a sequence of steps which includes preparing the pre-alloyed compounds, pulverizing them into a fine powder, compacting in suitable sizes and shapes, and sintering. Samples prepared by these procedures are carefully characterized by scanning electron microscopy, x-ray diffraction, dilatometry, and magnetic measurements. Process steps are found to exert important influences upon densities, microstructure and magnetic properties attained after densification. Investigations on a number of these process steps, including milling time and medium, sintering, and magnetic powder alignment are described

Metallurgical study and phase diagram calculations of the Zr-Nb-Fe-(Sn,O) system

International Nuclear Information System (INIS)

Toffolon, C.

2000-01-01

The Framatome M5 TM Zr-Nb-O alloy with small amounts of Fe is of interest for nuclear applications (PWR fuel cladding).The behaviour of this kind of alloy for in-service conditions strongly depends on the microstructure. Therefore, a metallurgical study of alloys of the Zr-Nb-Fe-(O-Sn) system has been developed in order to study the influence of chemical composition variabilities of Nb, Fe and O and thermal treatments on the resultant microstructure. In order to get some insight on the physical metallurgy of Zr-Nb-Fe-(Sn,O) alloys and to minimize the experiments, it is useful to build a thermodynamic database. With this object, it was necessary to re-optimize and to calculate the low order binary systems such as Fe-Nb and Nb-Sn in order to assess the Zr-Nb-Fe-(Sn,O) system. Then, the experimental studies concerned: the influence of small variations in Nb and O contents on the α/β transus temperatures. A comparison between experimental results and thermodynamic predictions showed a good agreement; the precipitation kinetics of βNb and intermetallic phases in the α phase domain. These experiments showed that the kinetics depends on the initial metallurgical conditions; the determination of the crystallographic structure and the stoichiometry of the ternary Zr-Nb-Fe intermetallic compounds as a function of the temperature. Finally, these experimental data were used to propose a first assessment of the Zr-Nb-Fe(O∼1200 ppm) system. (author)

Implications of a Culturally Evolved Self for Notions of Free Will

Directory of Open Access Journals (Sweden)

Lloyd Hawkeye Robertson

2017-10-01

Full Text Available Most schools in psychology have emphasized individual choice despite evidence of genetic and cultural determinism. It is suggested in this paper that the rejection of classical behaviorism by psychology and other humanities flowed from deeply held cultural assumptions about volition and free will. While compatibilists have suggested that notions of free will and determinism are not mutually exclusive, the psychological mechanisms by which such an accommodation could be explained have been inadequately explored. Drawing on research into classical cultures, this paper builds an argument that the notion of free will was adaptive flowing from culturally evolved changes to the self, and that this “evolved self,” containing assumptions of personal volition, continuity, and reason, became benchmarks of what it means to be human. The paper proposes a model of a culturally evolved self that is compatible with understandings of free will and determinism. Implications for therapeutic practice and future research are discussed.

Metallurgical and acoustical characterization of a hydroformed, 304 stainless steel, Caribbean-style musical pan

International Nuclear Information System (INIS)

Murr, L.E.; Gaytan, S.M.; Lopez, M.I.; Bujanda, D.E.; Martinez, E.Y.; Whitmyre, G.; Price, H.

2008-01-01

We report herein the metallurgical and acoustical characterization of hydroformed 304 stainless steel, Caribbean pans. These pans were fully tuned to chromatic tones and compared to a manufactured, low-carbon, Caribbean steel pan standard. Hydroformed platforms had a Vickers microindentation hardness of HV 345, which was reduced by annealing during pan fabrication to HV 270. Skirts welded to the hydroformed head had a microindentation hardness of HV 440. Microstructural characterization by light optical metallography and transmission electron microscopy illustrated microstructures (including grain structures) characteristic of these pan microindentation hardnesses

Proceedings of papers. 3. Balkan Metallurgical Conference; Kniga na trudovi. 3-ta Balkanska konferencija na metalurzite

Energy Technology Data Exchange (ETDEWEB)

Mickovski, Jovan [Faculty of Technology and Metallurgy, St. ' Cyril and Methodius' University, Skopje (Macedonia, The Former Yugoslav Republic of)

2003-07-01

This Conference aims to be a central event in the metallurgy research of Balkan, fulfilling the goals to present the most outstanding relevant developments in modern metallurgy; to inspire high standards of excellence in pure and applied metallurgy research; to attract outstanding scientists to present central lectures on modem metallurgical research, and on the challenges imposed by the needs of society; to inspire the young generation of metallurgists in Balkan and other countries. Following these lines, the 3. Balkan Conference on Metallurgy will provide a unique opportunity for academic and industrial metallurgists from the Balkan countries and wider, to exchange ideas, expertise, and experience on topics related to the theme of the Conference - Balkan Metallurgy in Search for New Ways of Development. The aim of the organizers was to bring together distinguished experts, not only to present their work, but also to discuss the major scientific and technological challenges facing metallurgy in this millennium.The 6 sections of the conference were entitled: Section A: Extractive metallurgy; Section B: Physical metallurgy and materials science - ferrous metals and non ferrous metals; Section C: Management, maintenance control and optimization of metallurgical processes; Section D: New technologies and techniques; Section E: Refractory and powder; Section F: Corrosion and protection of metals. Papers relevant to INIS are indexed separately.

Robustness to Faults Promotes Evolvability: Insights from Evolving Digital Circuits.

Science.gov (United States)

Milano, Nicola; Nolfi, Stefano

2016-01-01

We demonstrate how the need to cope with operational faults enables evolving circuits to find more fit solutions. The analysis of the results obtained in different experimental conditions indicates that, in absence of faults, evolution tends to select circuits that are small and have low phenotypic variability and evolvability. The need to face operation faults, instead, drives evolution toward the selection of larger circuits that are truly robust with respect to genetic variations and that have a greater level of phenotypic variability and evolvability. Overall our results indicate that the need to cope with operation faults leads to the selection of circuits that have a greater probability to generate better circuits as a result of genetic variation with respect to a control condition in which circuits are not subjected to faults.

Powder metallurgical high performance materials. Proceedings. Volume 2: P/M hard materials

Energy Technology Data Exchange (ETDEWEB)

Kneringer, G; Roedhammer, P; Wildner, H [eds.

2001-07-01

The proceedings of these seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. There the ingenuity and assiduous work of thousands of scientists and engineers striving for progress in the field of powder metallurgy is documented in more than 2000 contributions covering some 30000 pages. The 15{sup th} Plansee Seminar was convened under the general theme 'Powder Metallurgical High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (author)

Powder metallurgical high performance materials. Proceedings. Volume 2: P/M hard materials

International Nuclear Information System (INIS)

Kneringer, G.; Roedhammer, P.; Wildner, H.

2001-01-01

The proceedings of these seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. There the ingenuity and assiduous work of thousands of scientists and engineers striving for progress in the field of powder metallurgy is documented in more than 2000 contributions covering some 30000 pages. The 15 th Plansee Seminar was convened under the general theme 'Powder Metallurgical High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (author)

Preface: evolving rotifers, evolving science: Proceedings of the XIV International Rotifer Symposium

Czech Academy of Sciences Publication Activity Database

Devetter, Miloslav; Fontaneto, D.; Jersabek, Ch.D.; Welch, D.B.M.; May, L.; Walsh, E.J.

2017-01-01

Roč. 796, č. 1 (2017), s. 1-6 ISSN 0018-8158 Institutional support: RVO:60077344 Keywords : evolving rotifers * 14th International Rotifer Symposium * evolving science Subject RIV: EG - Zoology OBOR OECD: Zoology Impact factor: 2.056, year: 2016

Oxide nano-rod array structure via a simple metallurgical process

International Nuclear Information System (INIS)

Nanko, M; Do, D T M

2011-01-01

A simple method for fabricating oxide nano-rod array structure via metallurgical process is reported. Some dilute alloys such as Ni(Al) solid solution shows internal oxidation with rod-like oxide precipices during high-temperature oxidation with low oxygen partial pressure. By removing a metal part in internal oxidation zone, oxide nano-rod array structure can be developed on the surface of metallic components. In this report, Al 2 O 3 or NiAl 2 O 4 nano-rod array structures were prepared by using Ni(Al) solid solution. Effects of Cr addition into Ni(Al) solid solution on internal oxidation were also reported. Pack cementation process for aluminizing of Ni surface was applied to prepare nano-rod array components with desired shape. Near-net shape Ni components with oxide nano-rod array structure on their surface can be prepared by using the pack cementation process and internal oxidation,

Evolutionary Policy Transfer and Search Methods for Boosting Behavior Quality: RoboCup Keep-Away Case Study

Directory of Open Access Journals (Sweden)

Geoff Nitschke

2017-11-01

Full Text Available This study evaluates various evolutionary search methods to direct neural controller evolution in company with policy (behavior transfer across increasingly complex collective robotic (RoboCup keep-away tasks. Robot behaviors are first evolved in a source task and then transferred for further evolution to more complex target tasks. Evolutionary search methods tested include objective-based search (fitness function, behavioral and genotypic diversity maintenance, and hybrids of such diversity maintenance and objective-based search. Evolved behavior quality is evaluated according to effectiveness and efficiency. Effectiveness is the average task performance of transferred and evolved behaviors, where task performance is the average time the ball is controlled by a keeper team. Efficiency is the average number of generations taken for the fittest evolved behaviors to reach a minimum task performance threshold given policy transfer. Results indicate that policy transfer coupled with hybridized evolution (behavioral diversity maintenance and objective-based search addresses the bootstrapping problem for increasingly complex keep-away tasks. That is, this hybrid method (coupled with policy transfer evolves behaviors that could not otherwise be evolved. Also, this hybrid evolutionary search was demonstrated as consistently evolving topologically simple neural controllers that elicited high-quality behaviors.

Metallurgical Effects of Shunting Current on Resistance Spot-Welded Joints of AA2219 Sheets

Science.gov (United States)

Jafari Vardanjani, M.; Araee, A.; Senkara, J.; Jakubowski, J.; Godek, J.

2016-08-01

Shunting effect is the loss of electrical current via the secondary circuit provided due to the existence of previous nugget in a series of welding spots. This phenomenon influences on metallurgical aspects of resistance spot-welded (RSW) joints in terms of quality and performance. In this paper RSW joints of AA2219 sheets with 1 mm thickness are investigated metallurgically for shunted and single spots. An electro-thermal finite element analysis is performed on the RSW process of shunted spot and temperature distribution and variation are obtained. These predictions are then compared with experimental micrographs. Three values of 5 mm, 20 mm, and infinite (i.e., single spot) are assumed for welding distance. Numerical and experimental results are matching each other in terms of nugget and HAZ geometry as increasing distance raised nugget size and symmetry of HAZ. In addition, important effect of shunting current on nugget thickness, microstructure, and Copper segregation on HAZ grain boundaries were discovered. A quantitative analysis is also performed about the influence of welding distance on important properties including ratio of nugget thickness and diameter ( r t), ratio of HAZ area on shunted and free side of nugget ( r HA), and ratio of equivalent segregated and total amount of Copper, measured in sample ( r Cu) on HAZ. Increasing distance from 5 mm to infinite, indicated a gain of 111.04, -45.55, and -75.15% in r t, r HA, and r Cu, respectively, while obtained ratios for 20 mm welding distance was suitable compared to single spot.

An environmentally-friendly vacuum reduction metallurgical process to recover germanium from coal fly ash

Energy Technology Data Exchange (ETDEWEB)

Zhang, Lingen; Xu, Zhenming, E-mail: zmxu@sjtu.edu.cn

2016-07-15

Highlights: • An environmental friendly vacuum reduction metallurgical process is proposed. • Rare and valuable metal germanium from coal fly ash is recycled. • Residues are not a hazardous material and can be further recycled. • A germanium recovery ratio of 94.64% is obtained in pilot scale experiments. - Abstract: The demand for germanium in the field of semiconductor, electronics, and optical devices is growing rapidly; however, the resources of germanium are scarce worldwide. As a secondary material, coal fly ash could be further recycled to retrieve germanium. Up to now, the conventional processes to recover germanium have two problems as follows: on the one hand, it is difficult to be satisfactory for its economic and environmental effect; on the other hand, the recovery ratio of germanium is not all that could be desired. In this paper, an environmentally-friendly vacuum reduction metallurgical process (VRMP) was proposed to recover germanium from coal fly ash. The results of the laboratory scale experiments indicated that the appropriate parameters were 1173 K and 10 Pa with 10 wt% coke addition for 40 min, and recovery ratio germanium was 93.96%. On the basis of above condition, the pilot scale experiments were utilized to assess the actual effect of VRMP for recovery of germanium with parameter of 1473 K, 1–10 Pa and heating time 40 min, the recovery ratio of germanium reached 94.64%. This process considerably enhances germanium recovery, meanwhile, eliminates much of the water usage and residue secondary pollution compared with other conventional processes.

M-Area and Metallurgical Laboratory Hazardous Waste Management Facilities Groundwater Monitoring and Corrective-Action Report, First and Second Quarters 1999, Volume III

International Nuclear Information System (INIS)

Chase, J.

1999-01-01

This report describes the groundwater monitoring and corrective-action program at the M-Area Hazardous Waste Management Facility (HWMF) and the Metallurgical Laboratory (Met Lab) HWMF at the Savannah River Site (SRS) during the first and second quarters 1999

Metallurgical Characterization of a Weld Bead Coating Applied by the PTA Process on the D2 Tool Steel

Directory of Open Access Journals (Sweden)

Ali Tahaei

Full Text Available Abstract In this investigation, a nickel-base powder mixed with tungsten carbide particles was applied by Plasma Transferred Arc welding (PTA on the surface of the D2 cold work tool steel to improve surface quality and to extend its lifetime during applications. The Design of Experiment (DoE method was applied to obtain the appropriate combination of hardfacing parameters and to run the minimum number of tests. Current, travel speed and preheat were considered as variable parameters. These parameters are important to reach a final layer with an appropriate bead geometry accompanied with good metallurgical properties. All samples were prepared for metallurgical investigations and the effect of process parameters on the weld bead geometry was considered. For each experiment run, weld bead geometry parameters were measured including dilution, penetration and reinforcement. Microstructures and the distribution of tungsten carbide particles after welding were analyzed by Optical Microscopy (OM and Scanning Electron Microscopy (SEM equipped with an EDS microprobe. In addition, hardness tests were performed to evaluate the mechanical properties of the weld bead layers. Finally, among all the experiments, the best sample with appropriate bead geometry and microstructure was selected.

ECOLOGICAL MANAGEMENT IN THE MINING AND METALLURGICAL MARAMURES AREA

Directory of Open Access Journals (Sweden)

Viorel POP

2015-04-01

Full Text Available The paper is part of the interdisciplinary recent concerns of "environmental management", looking to determine the damages caused by pollution, remediation expenditures, and benefits that may arise through the application of remediation techniques and decontamination technologies in the mining and metallurgical Maramureş area. Large areas of land were diverted from their original destination (pastures, arable land, forests being now covered with ponds and dumps of mine or flotation tailings, deposits that are insufficiently protected, and have become sources of pollution to surrounding areas. All Eastern European countries have in common major environmental problems, the most serious being due to mining, metallurgy and chemistry. In the relationship of "economic-ecological" equilibrium, should be considered both economic criteria, as well as ecological ones. Pollution as the deterioration of environment, requires costs for rehabilitation of degraded areas, and for environmental protection, costs for new technologies, non polluting ones. The assessment foundation of environmental damages, is necessary for establishing the priority directions in the allocation of funds for projects to protect and rehabilitate the environment.

Determination of Japanese buyer valuation of metallurgical coal characteristics by hedonic modeling

Energy Technology Data Exchange (ETDEWEB)

Koerner, R.J. [Griffith University, Brisbane, Qld. (Australia). Graduate School of Management

2001-09-01

Considerable efforts have been devoted by econometric researchers to understanding Japanese steel mill (JSM) metallurgical coal valuation policies, and whether such policies disadvantage coal exporters. Much of this research has employed the hedonic regression modeling technique of Rosen and examines the significance of coal quality in establishing market price. This article discusses shortcomings in some such modeling studies, and presents results of additional hedonic modeling to buttress findings of previous work suggesting that cross-cultural bargaining factors rather than coal quality explain lower prices for Australian coals in Japanese market settlements. Policy changes that might be effective in ameliorating bilateral market distortions arising from oligopsony characteristics exhibited in JSM contract settlements are then explored. 29 refs., 2 figs., 2 tabs.

Pb pollution from leaded gasoline in South America in the context of a 2000-year metallurgical history.

Science.gov (United States)

Eichler, Anja; Gramlich, Gabriela; Kellerhals, Thomas; Tobler, Leonhard; Schwikowski, Margit

2015-03-01

Exploitation of the extensive polymetallic deposits of the Andean Altiplano in South America since precolonial times has caused substantial emissions of neurotoxic lead (Pb) into the atmosphere; however, its historical significance compared to recent Pb pollution from leaded gasoline is not yet resolved. We present a comprehensive Pb emission history for the last two millennia for South America, based on a continuous, high-resolution, ice core record from Illimani glacier. Illimani is the highest mountain of the eastern Bolivian Andes and is located at the northeastern margin of the Andean Altiplano. The ice core Pb deposition history revealed enhanced Pb enrichment factors (EFs) due to metallurgical processing for silver production during periods of the Tiwanaku/Wari culture (AD 450-950), the Inca empires (AD 1450-1532), colonial times (AD 1532-1900), and tin production at the beginning of the 20th century. After the 1960s, Pb EFs increased by a factor of 3 compared to the emission level from metal production, which we attribute to gasoline-related Pb emissions. Our results show that anthropogenic Pb pollution levels from road traffic in South America exceed those of any historical metallurgy in the last two millennia, even in regions with exceptional high local metallurgical activity.

Pb pollution from leaded gasoline in South America in the context of a 2000-year metallurgical history

Science.gov (United States)

Eichler, Anja; Gramlich, Gabriela; Kellerhals, Thomas; Tobler, Leonhard; Schwikowski, Margit

2015-01-01

Exploitation of the extensive polymetallic deposits of the Andean Altiplano in South America since precolonial times has caused substantial emissions of neurotoxic lead (Pb) into the atmosphere; however, its historical significance compared to recent Pb pollution from leaded gasoline is not yet resolved. We present a comprehensive Pb emission history for the last two millennia for South America, based on a continuous, high-resolution, ice core record from Illimani glacier. Illimani is the highest mountain of the eastern Bolivian Andes and is located at the northeastern margin of the Andean Altiplano. The ice core Pb deposition history revealed enhanced Pb enrichment factors (EFs) due to metallurgical processing for silver production during periods of the Tiwanaku/Wari culture (AD 450–950), the Inca empires (AD 1450–1532), colonial times (AD 1532–1900), and tin production at the beginning of the 20th century. After the 1960s, Pb EFs increased by a factor of 3 compared to the emission level from metal production, which we attribute to gasoline-related Pb emissions. Our results show that anthropogenic Pb pollution levels from road traffic in South America exceed those of any historical metallurgy in the last two millennia, even in regions with exceptional high local metallurgical activity. PMID:26601147

NMR investigation of boron impurities in refined metallurgical grade silicon

Energy Technology Data Exchange (ETDEWEB)

Grafe, Hans-Joachim; Loeser, Wolfgang; Schmitz, Steffen; Sakaliyska, Miroslava [Leibniz Institute for Solid State and Materials Research (IFW), Dresden (Germany); Wurmehl, Sabine [Leibniz Institute for Solid State and Materials Research (IFW), Dresden (Germany); Institute for Solid State Physics, Technische Universitaet Dresden (Germany); Eisert, Stefan; Reichenbach, Birk; Mueller, Tim [Adensis GmbH, Dresden (Germany); Acker, Joerg; Rietig, Anja; Ducke, Jana [Department of Chemistry, Faculty for Natural Sciences, Brandenburg Technical University Cottbus-Senftenberg, Senftenberg (Germany)

2015-09-15

The nuclear magnetic resonance (NMR) method was applied for tracking boron impurities in the refining process of metallurgical grade (MG) silicon. From the NMR signal of the {sup 11}B isotope at an operating temperature 4.2 K, the boron concentration can be estimated down to the order of 1-10 wppm B. After melting and resolidification of MG-Si alloyed with Ca and Ti, a major fraction of B impurities remains in the Si solid solution as inferred from the characteristic NMR frequency. The alloying element Ti does not form substantial fractions of TiB{sub 2}. Acid leaching of crushed powders of MG-Si alloyed with Ca and Ti can diminish the initial impurity content of B suggesting its accumulation in the grain boundary phases. NMR signals of TiB{sub 2} at 4.2 K and room temperature (RT), and of poly-Si with different B doping at 4.2 K. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Friction, adhesion and corrosion performance of metallurgical coatings in HTGR-helium

International Nuclear Information System (INIS)

Engel, R.; Kleemann, W.

1981-01-01

The friction-, adhesion-, thermal cycling- and corrosion performance of several metallurgical coating systems have been tested in a simulated HTGR-test atmosphere at elevated temperatures. The coatings were applied to a solid solution strengthened Ni-based superalloy. Component design requires coatings for the protection of mating surfaces, since under reactor operating conditions, contacting surfaces of metallic components under high pressures are prone to friction and wear damage. The coatings will have to protect the metal surface for 30 years up to 950 0 C in HTGR-helium. The materials tested were various refractory carbides with or without metallic binders and intermetallic compounds. The coatings evaluated were applied by plasma spraying-, detonation gun- and chemical vapor deposition techniques. These yielded two types of coatings which employ different mechanisms to improve the tribiological properties and maintain coating integrity. (Auth.)

Method of purifying metallurgical grade silicon employing reduced pressure atmospheric control

Science.gov (United States)

Ingle, W. M.; Thompson, S. W.; Chaney, R. E. (Inventor)

1979-01-01

A method in which a quartz tube is charged with chunks of metallurgical grade silicon and/or a mixture of such chunks and high purity quartz sand, and impurities from a class including aluminum, boron, as well as certain transition metals including nickel, iron, and manganese is described. The tube is then evacuated and heated to a temperature within a range of 800 C to 1400 C. A stream of gas comprising a reactant, such as silicon tetrafluoride, is continuously delivered at low pressures through the charge for causing a metathetical reaction of impurities of the silicon and the reactant to occur for forming a volatile halide and leaving a residue of silicon of an improved purity. The reactant which included carbon monoxide gas and impurities such as iron and nickel react to form volatile carbonyls.

Clustering impact regime with shocks in freely evolving granular gas

Science.gov (United States)

Isobe, Masaharu

2017-06-01

A freely cooling granular gas without any external force evolves from the initial homogeneous state to the inhomogeneous clustering state, at which the energy decay deviates from the Haff's law. The asymptotic behavior of energy in the inelastic hard sphere model have been predicted by several theories, which are based on the mode coupling theory or extension of inelastic hard rods gas. In this study, we revisited the clustering regime of freely evolving granular gas via large-scale molecular dynamics simulation with up to 16.7 million inelastic hard disks. We found novel regime regarding on collisions between "clusters" spontaneously appearing after clustering regime, which can only be identified more than a few million particles system. The volumetric dilatation pattern of semicircular shape originated from density shock propagation are well characterized on the appearing of "cluster impact" during the aggregation process of clusters.

Breeding a Diversity of Super Mario Behaviors Through Interactive Evolution

DEFF Research Database (Denmark)

Sørensen, Patrikk D.; Olsen, Jeppeh M.; Risi, Sebastian

2016-01-01

. In this paper, we show how casual users can create controllers for Super Mario Bros. through an interactive evolutionary computation (IEC) approach, without prior domain or programming knowledge. By iteratively selecting Super Mario behaviors from a set of candidates, users are able to guide evolution towards...... behaviors they prefer. The result of a user test show that the participants are able to evolve controllers with very diverse behaviors, which would be difficult through automated approaches. Additionally, the user-evolved controllers perform as well as controllers evolved with a traditional fitness...

Predator confusion is sufficient to evolve swarming behavior

OpenAIRE

Olson, Randal S.; Hintze, Arend; Dyer, Fred C.; Knoester, David B.; Adami, Christoph

2012-01-01

Swarming behaviors in animals have been extensively studied due to their implications for the evolution of cooperation, social cognition, and predator-prey dynamics. An important goal of these studies is discerning which evolutionary pressures favor the formation of swarms. One hypothesis is that swarms arise because the presence of multiple moving prey in swarms causes confusion for attacking predators, but it remains unclear how important this selective force is. Using an evolutionary model...

Powder metallurgical high performance materials. Proceedings. Volume 1: high performance P/M metals

International Nuclear Information System (INIS)

Kneringer, G.; Roedhammer, P.; Wildner, H.

2001-01-01

The proceedings of this sequence of seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. There the ingenuity and assiduous work of thousands of scientists and engineers striving for progress in the field of powder metallurgy is documented in more than 2000 contributions covering some 30000 pages. The 15th Plansee Seminar was convened under the general theme 'Powder Metallurgical High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (author)

Powder metallurgical high performance materials. Proceedings. Volume 1: high performance P/M metals

Energy Technology Data Exchange (ETDEWEB)

Kneringer, G; Roedhammer, P; Wildner, H [eds.

2001-07-01

The proceedings of this sequence of seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. There the ingenuity and assiduous work of thousands of scientists and engineers striving for progress in the field of powder metallurgy is documented in more than 2000 contributions covering some 30000 pages. The 15th Plansee Seminar was convened under the general theme 'Powder Metallurgical High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (author)

Storytelling, behavior planning, and language evolution in context.

Science.gov (United States)

McBride, Glen

2014-01-01

An attempt is made to specify the structure of the hominin bands that began steps to language. Storytelling could evolve without need for language yet be strongly subject to natural selection and could provide a major feedback process in evolving language. A storytelling model is examined, including its effects on the evolution of consciousness and the possible timing of language evolution. Behavior planning is presented as a model of language evolution from storytelling. The behavior programming mechanism in both directions provide a model of creating and understanding behavior and language. Culture began with societies, then family evolution, family life in troops, but storytelling created a culture of experiences, a final step in the long process of achieving experienced adults by natural selection. Most language evolution occurred in conversations where evolving non-verbal feedback ensured mutual agreements on understanding. Natural language evolved in conversations with feedback providing understanding of changes.

How People Interact in Evolving Online Affiliation Networks

Science.gov (United States)

Gallos, Lazaros K.; Rybski, Diego; Liljeros, Fredrik; Havlin, Shlomo; Makse, Hernán A.

2012-07-01

The study of human interactions is of central importance for understanding the behavior of individuals, groups, and societies. Here, we observe the formation and evolution of networks by monitoring the addition of all new links, and we analyze quantitatively the tendencies used to create ties in these evolving online affiliation networks. We show that an accurate estimation of these probabilistic tendencies can be achieved only by following the time evolution of the network. Inferences about the reason for the existence of links using statistical analysis of network snapshots must therefore be made with great caution. Here, we start by characterizing every single link when the tie was established in the network. This information allows us to describe the probabilistic tendencies of tie formation and extract meaningful sociological conclusions. We also find significant differences in behavioral traits in the social tendencies among individuals according to their degree of activity, gender, age, popularity, and other attributes. For instance, in the particular data sets analyzed here, we find that women reciprocate connections 3 times as much as men and that this difference increases with age. Men tend to connect with the most popular people more often than women do, across all ages. On the other hand, triangular tie tendencies are similar, independent of gender, and show an increase with age. These results require further validation in other social settings. Our findings can be useful to build models of realistic social network structures and to discover the underlying laws that govern establishment of ties in evolving social networks.

Manganese Ores from South Sulawesi: Their Potential Uses as Raw Materials for Metallurgical Industry

Directory of Open Access Journals (Sweden)

Sufriadin Sufriadin

2017-03-01

Full Text Available Characterization of manganese ores from Barru and Bone regencies of South Sulawesi has been conducted with the aim at clarification of their mineralogical and chemical composition for their potential uses as the raw materials for metallurgical industry. Mineralogical properties of the ores analyzed by means of optical microscopy and X-ray diffractometry (XRD show that samples from Barru consist mainly of rhodochrosite (MnCO3 with less cryptomelane, groutite, bixbyite, and todorokite. Goethite, calcite and small amount of quartz present as impurities. Manganese ore samples from Bone are predominantly composed of pyrolusite (MnO2 with subordinate ramsdellite and hollandite. Barite, quartz, hematite and clay are present as gangue minerals. Chemical compositions determined by using XRF method revealed that Barru samples contain higher in MnO (average is 40.07 wt% than the Bone samples (average is 34.36 wt%. Similarly, Fe2O3 and CaO are also higher in Barru than those of the Bone samples. In contrast, concentrations of SiO2 and total alkali (K2O + Na2O are lower in the Barru samples. The average P2O5 content of samples in both areas is low (<0.2 wt%. Relatively higher grade of Fe2O3 in the Barru ore implies that it has potential application for ferromanganese production; whereas the elevated SiO2 content of the Bone ore is a good indication for silicomanganese manufacture. However, both ores may not favorable to be directly used as raw materials in metallurgical uses. Prior to be used, the ores should be treated by applying physical beneficiation in order to reduce deleterious elements.

Economic statistics for the mining and metallurgical industries: 1990. Statistique economique des industries extractives et metallurgiques annee 1990

Energy Technology Data Exchange (ETDEWEB)

Rzonzef, L.

1991-01-01

Provides economic statistics for the Belgian mining and metallurgical industries in 1990. The review is divided into 4 parts: the extractive industries (including an analysis of the coal market and mines, quarries and associated industries); coke and briquette making; metallurgy (i.e. blast furnaces, steel making, rolling mills and manpower and materials consumption in the steel industry); and the extraction of sand from the Belgian continental shelf. 17 tabs.

Natural selection promotes antigenic evolvability.

Science.gov (United States)

Graves, Christopher J; Ros, Vera I D; Stevenson, Brian; Sniegowski, Paul D; Brisson, Dustin

2013-01-01

The hypothesis that evolvability - the capacity to evolve by natural selection - is itself the object of natural selection is highly intriguing but remains controversial due in large part to a paucity of direct experimental evidence. The antigenic variation mechanisms of microbial pathogens provide an experimentally tractable system to test whether natural selection has favored mechanisms that increase evolvability. Many antigenic variation systems consist of paralogous unexpressed 'cassettes' that recombine into an expression site to rapidly alter the expressed protein. Importantly, the magnitude of antigenic change is a function of the genetic diversity among the unexpressed cassettes. Thus, evidence that selection favors among-cassette diversity is direct evidence that natural selection promotes antigenic evolvability. We used the Lyme disease bacterium, Borrelia burgdorferi, as a model to test the prediction that natural selection favors amino acid diversity among unexpressed vls cassettes and thereby promotes evolvability in a primary surface antigen, VlsE. The hypothesis that diversity among vls cassettes is favored by natural selection was supported in each B. burgdorferi strain analyzed using both classical (dN/dS ratios) and Bayesian population genetic analyses of genetic sequence data. This hypothesis was also supported by the conservation of highly mutable tandem-repeat structures across B. burgdorferi strains despite a near complete absence of sequence conservation. Diversification among vls cassettes due to natural selection and mutable repeat structures promotes long-term antigenic evolvability of VlsE. These findings provide a direct demonstration that molecular mechanisms that enhance evolvability of surface antigens are an evolutionary adaptation. The molecular evolutionary processes identified here can serve as a model for the evolution of antigenic evolvability in many pathogens which utilize similar strategies to establish chronic infections.

Natural selection promotes antigenic evolvability.

Directory of Open Access Journals (Sweden)

Christopher J Graves

Full Text Available The hypothesis that evolvability - the capacity to evolve by natural selection - is itself the object of natural selection is highly intriguing but remains controversial due in large part to a paucity of direct experimental evidence. The antigenic variation mechanisms of microbial pathogens provide an experimentally tractable system to test whether natural selection has favored mechanisms that increase evolvability. Many antigenic variation systems consist of paralogous unexpressed 'cassettes' that recombine into an expression site to rapidly alter the expressed protein. Importantly, the magnitude of antigenic change is a function of the genetic diversity among the unexpressed cassettes. Thus, evidence that selection favors among-cassette diversity is direct evidence that natural selection promotes antigenic evolvability. We used the Lyme disease bacterium, Borrelia burgdorferi, as a model to test the prediction that natural selection favors amino acid diversity among unexpressed vls cassettes and thereby promotes evolvability in a primary surface antigen, VlsE. The hypothesis that diversity among vls cassettes is favored by natural selection was supported in each B. burgdorferi strain analyzed using both classical (dN/dS ratios and Bayesian population genetic analyses of genetic sequence data. This hypothesis was also supported by the conservation of highly mutable tandem-repeat structures across B. burgdorferi strains despite a near complete absence of sequence conservation. Diversification among vls cassettes due to natural selection and mutable repeat structures promotes long-term antigenic evolvability of VlsE. These findings provide a direct demonstration that molecular mechanisms that enhance evolvability of surface antigens are an evolutionary adaptation. The molecular evolutionary processes identified here can serve as a model for the evolution of antigenic evolvability in many pathogens which utilize similar strategies to establish

Mineralogical test as a preliminary step for metallurgical proses of Kalan ores

International Nuclear Information System (INIS)

Affandi, K.

1998-01-01

Mineralogical tests as a preliminary step for hydrometallurgy of Kalan ores, including Eko Remaja and Rirang have been carried out to identify the elements and minerals content which affect the metallurgical process, especially the leaching and purification of uranium. Mineralogical tests have been done by means of radioactive and radioluxugraph tests to identify radioactive minerals; thin specimen analysis, Scanning Electron Microscopy (SEM) to identify elements and morphology, EPMA to analyse qualitatively the elements, X-ray Diffractometer (XRD) to identify of minerals content; and X-ray Fluorescence (XRF) and chemical analyses to determine total elements qualitatively and quantitatively. The experimental results show that the Eko Remaja ores contain uraninite and brannerite, iron and titan oxides, sulfides, phosphates and silicates minerals, while the Rirang ores contain uraninite, monazite and molybdenite

Influence of material and gear parameters on the safety of gearing in metallurgical industry

Directory of Open Access Journals (Sweden)

S. Medvecká - Beňová

2015-01-01

Full Text Available This paper deals with the appropriate choice of parameters to obtain the desired level of safety of gears in a gearbox to drive the conveyor in the metallurgical industry under increased load. Steel with surface hardness up to 350 HBW, or heat treated steel with hardness of 500 - 650 HBW are used. As a final heat treatment are used surface hardening, cementation and hardening, nitridation. Good properties of heat-treated steels are at the correct thickness of the heat-treated layer of the tooth. Results are presented for dual-ratio gearbox with spur gears from operation of an integrated steel company.

Seed production of woody plants in conditions of environment pollution by metallurgical industry emissions

Directory of Open Access Journals (Sweden)

Z. V. Gritzay

2011-10-01

Full Text Available The influence of environment pollution by metallurgical industry emissions on woody plants bearing parameters was examined. The results obtained show the decrease of bearing rate, diminution of seeds, fruits and seed cells sizes in woody plants affected by technogenic emissions. Attenuation of the 1000 seeds’ weight was established. Incresing the amount of fruits with development deviations was ascertained. It was found aplasia and abnormal form of the samara fruit of ash and ailanthus trees, arcuation and narrowing of some parts of the catalpa fruitcases. Practical recommendations on using seeds’ sensitive parameters in biomonitoring of woody phytocenoses under technogenic stressful conditions are proposed.

A metallurgical study of some viking swords

Directory of Open Access Journals (Sweden)

Williams, Alan

2009-12-01

Full Text Available While «pattern-welded» swords have been found all over Europe from sites dating from the Migration Period and into the Early Middle Ages, they were steadily supplanted during the Viking period by swords made out of a few pieces of iron and steel, or even a single piece of steel. Swords with «Ulfberht» or related inscriptions were the most famous of these. The results of the metallurgical study of 44 specimens from «Ulfberht» swords, as well as some other Viking-age swords, together with electron microanalyses carried out on selected examples, are presented here.

Mientras que se han encontrado en toda Europa espadas forjadas mediante el sistema de ‘pattern welding’ (entrelazado de láminas formando patrones visibles, procedentes de yacimientos que se extienden desde el Periodo de las Migraciones bárbaras hasta la Alta Edad Media, durante el periodo vikingo fueron habitualmente reemplazadas por espadas forjadas a partir de unas pocas piezas de hierro y acero, o incluso de una única pieza de acero. Las más famosas de entre ellas fueron las espadas con la inscripción «Ulfbehrt» u otras relacionadas. Este artículo presenta los resultados del estudio metalúrgico de 44 ejemplares de espadas de «Ulfberht» y otras de época vikinga, así como los microanálisis efectuados sobre algunas muestras seleccionadas.

Application of the VAW tube digester for metallurgical pressure-leaching processes

International Nuclear Information System (INIS)

Kaempf, F.; Pietsch, H.B.

1978-01-01

Problems associated with the treatment of complex and refractory ores or concentrates, as well as those related to environmental factors, have led to increased interest in hydrometallurgy under elevated temperatures and pressures. Pressure leaching can be carried out in vertical, horizontal or spherical autoclaves equipped with mechanical agitators. If high throughput capacities are catered for, the division of a conventional plant into several units is inevitable. By contrast, the VAW (Vereinigte Aluminium-Werke Aktiengesellschaft) tube digester enables hydrometallurgical processes to be carried out under pressure and at a high temperature with the use of a basically simple technology, extremely high specific throughput and improved thermal economics being achieved. The advantages of the tube digester over vessel autoclaves are described, and details of laboratory investigations into the applicability of tube digesters to various metallurgical applications are given. Test results are given for the leaching of refractory uranium ores. (author)

Metallurgical Laboratory Hazardous Waste Management Facility groundwater monitoring report

International Nuclear Information System (INIS)

Thompson, C.Y.

1993-03-01

During fourth quarter 1992, samples from 18 groundwater monitoring wells of the AMB series at the Metallurgical Laboratory Hazardous Waste Management Facility were analyzed for certain heavy metals, indicator parameters, radionuclides, volatile organic compounds, and other constituents. Six parameters exceeded final Primary Drinking Water Standards (PDWS) and the Savannah River Site Flag 2 criteria during the quarter. The results for fourth quarter 1992 are fairly consistent with the rest of the year's data. Tetrachloroethylene exceeded the final PDWS in well AMB 4D only two of the four quarters; in the other three wells in which it was elevated, it was present at similar levels throughout the year. Trichloroethylene consistently exceeded its PDWS in wells AMB 4A, 4B, 4D, 5, and 7A during the year. Trichloroethylene was elevated in well AMB 6 only during third and fourth quarters and in well AMB 7 only during fourth quarter. Total alpha-emitting radium was above the final PDWS for total radium in well AMB 5 at similar levels throughout the year and exceeded the PDWS during one of the three quarters it was analyzed for (third quarter 1992) in well AMB 10B

Storytelling, behavior planning and language evolution in context.

Directory of Open Access Journals (Sweden)

Glen eMcbride

2014-10-01

Full Text Available An attempt is made to specify the structure of the hominin bands that began steps to language. 8 Storytelling could evolve without need for language yet be strongly subject to natural selection 9 and could provide a major feedback process in evolving language. A storytelling model is 10 examined, including its effects on the evolution of consciousness and the possible timing of 11 language evolution. Behavior planning is presented as a model of language evolution from 12 storytelling. The behavior programming mechanism in both directions provide a model of 13 creating and understanding behavior and language. Culture began with societies, then family 14 evolution, family life in troops, but storytelling created a culture of experiences, a final step in 15 the long process of achieving experienced adults by natural selection. Most language evolution 16 occurred in conversations where evolving non-verbal feedback ensured mutual agreements on 17 understanding. Natural language evolved in conversations with feedback providing 18 understanding of changes.

The hippocampus and exploration: dynamically evolving behavior and neural representations

Science.gov (United States)

Johnson, Adam; Varberg, Zachary; Benhardus, James; Maahs, Anthony; Schrater, Paul

2012-01-01

We develop a normative statistical approach to exploratory behavior called information foraging. Information foraging highlights the specific processes that contribute to active, rather than passive, exploration and learning. We hypothesize that the hippocampus plays a critical role in active exploration through directed information foraging by supporting a set of processes that allow an individual to determine where to sample. By examining these processes, we show how information directed information foraging provides a formal theoretical explanation for the common hippocampal substrates of constructive memory, vicarious trial and error behavior, schema-based facilitation of memory performance, and memory consolidation. PMID:22848196

The hippocampus and exploration: dynamically evolving behavior and neural representations

Directory of Open Access Journals (Sweden)

Adam eJohnson

2012-07-01

Full Text Available We develop a normative statistical approach to exploratory behavior called information foraging. Information foraging highlights the specific processes that contribute to active, rather than passive, exploration and learning. We hypothesize that the hippocampus plays a critical role in active exploration through directed information foraging by supporting a set of processes that allow an individual to determine where to sample. By examining these processes, we show how information directed information foraging provides a formal theoretical explanation for the common hippocampal substrates of constructive memory, vicarious trial and error behavior, schema-based facilitation of memory performance, and memory consolidation.

Quasispecies-like behavior observed in catalytic RNA populations evolving in a test tube.

Science.gov (United States)

Díaz Arenas, Carolina; Lehman, Niles

2010-03-23

During the RNA World, molecular populations were probably very small and highly susceptible to the force of strong random drift. In conjunction with Muller's Ratchet, this would have imposed difficulties for the preservation of the genetic information and the survival of the populations. Mechanisms that allowed these nascent populations to overcome this problem must have been advantageous. Using continuous in vitro evolution experimentation with an increased mutation rate imposed by MnCl2, it was found that clonal 100-molecule populations of ribozymes clearly exhibit certain characteristics of a quasispecies. This is the first time this has been seen with a catalytic RNA. Extensive genotypic sampling from two replicate lineages was gathered and phylogenetic networks were constructed to elucidate the structure of the evolving RNA populations. A common distribution was found in which a mutant sequence was present at high frequency, surrounded by a cloud of mutant with lower frequencies. This is a typical distribution of quasispecies. Most of the mutants in these clouds were connected by short Hamming distance values, indicating their close relatedness. The quasispecies nature of mutant RNA clouds facilitates the recovery of genotypes under pressure of being removed from the population by random drift. The empirical populations therefore evolved a genotypic resiliency despite a high mutation rate by adopting the characteristics of quasispecies, implying that primordial RNA pools could have used this strategy to avoid extinction.

Perspectives in metallurgical development. Proceedings of the centenary conference held at Ranmoor House, Sheffield, GB, on 16-18 July 1984

International Nuclear Information System (INIS)

1984-07-01

Forty one papers were presented on perspectives in metallurgical development, with sessions on historical metallurgy, extraction and process metallurgy, solidification processes, microstructural studies, working and forming, mechanical behaviour, corrosion and environmental effects, and future developments in metallurgy. One paper, on fracture mechanics and non-destructive testing related to assurance of structural integrity of nuclear pressure vessels, is indexed separately. (U.K.)

An evolving model of online bipartite networks

Science.gov (United States)

Zhang, Chu-Xu; Zhang, Zi-Ke; Liu, Chuang

2013-12-01

Understanding the structure and evolution of online bipartite networks is a significant task since they play a crucial role in various e-commerce services nowadays. Recently, various attempts have been tried to propose different models, resulting in either power-law or exponential degree distributions. However, many empirical results show that the user degree distribution actually follows a shifted power-law distribution, the so-called Mandelbrot’s law, which cannot be fully described by previous models. In this paper, we propose an evolving model, considering two different user behaviors: random and preferential attachment. Extensive empirical results on two real bipartite networks, Delicious and CiteULike, show that the theoretical model can well characterize the structure of real networks for both user and object degree distributions. In addition, we introduce a structural parameter p, to demonstrate that the hybrid user behavior leads to the shifted power-law degree distribution, and the region of power-law tail will increase with the increment of p. The proposed model might shed some lights in understanding the underlying laws governing the structure of real online bipartite networks.

Modeling Temporal Behavior in Large Networks: A Dynamic Mixed-Membership Model

Energy Technology Data Exchange (ETDEWEB)

Rossi, R; Gallagher, B; Neville, J; Henderson, K

2011-11-11

Given a large time-evolving network, how can we model and characterize the temporal behaviors of individual nodes (and network states)? How can we model the behavioral transition patterns of nodes? We propose a temporal behavior model that captures the 'roles' of nodes in the graph and how they evolve over time. The proposed dynamic behavioral mixed-membership model (DBMM) is scalable, fully automatic (no user-defined parameters), non-parametric/data-driven (no specific functional form or parameterization), interpretable (identifies explainable patterns), and flexible (applicable to dynamic and streaming networks). Moreover, the interpretable behavioral roles are generalizable, computationally efficient, and natively supports attributes. We applied our model for (a) identifying patterns and trends of nodes and network states based on the temporal behavior, (b) predicting future structural changes, and (c) detecting unusual temporal behavior transitions. We use eight large real-world datasets from different time-evolving settings (dynamic and streaming). In particular, we model the evolving mixed-memberships and the corresponding behavioral transitions of Twitter, Facebook, IP-Traces, Email (University), Internet AS, Enron, Reality, and IMDB. The experiments demonstrate the scalability, flexibility, and effectiveness of our model for identifying interesting patterns, detecting unusual structural transitions, and predicting the future structural changes of the network and individual nodes.

Peer review of the Three Mile Island Unit 2 Vessel Investigation Project metallurgical examinations

Energy Technology Data Exchange (ETDEWEB)

Bohl, R.W.; Gaydos, R.G.; Vander Voort, G.F.; Diercks, D.R. [Argonne National Lab., IL (United States)

1994-07-01

Fifteen samples recovered from the lower head of the Three Mile Island (TMI) Unit 2 nuclear reactor pressure vessel were subjected to detailed metallurgical examinations by the Idaho National Engineering Laboratory (INEL), with supporting work carried out by Argonne National Laboratory (ANL) and several of the European participants. These examinations determined that a portion of the lower head, a so-called elliptical ``hot spot`` measuring {approx}0.8 {times} 1 m, reached temperatures as high as 1100{degrees}C during the accident and cooled from these temperatures at {approx}10--100{degrees}C/min. The remainder of the lower head was found to have remained below the ferrite-toaustenite transformation temperature of 727{degrees}C during the accident. Because of the significance of these results and their importance to the overall analysis of the TMI accident, a panel of three outside peer reviewers, Dr. Robert W. Bohl, Mr. Richard G. Gaydos, and Mr. George F. Vander Voort, was formed to conduct an independent review of the metallurgical analyses. After a thorough review of the previous analyses and examination of photo-micrographs and actual lower head specimens, the panel determined that the conclusions resulting from the INEL study were fundamentally correct. In particular, the panel reaffirmed that four lower head samples attained temperatures as high as 1100{degrees}C, and perhaps as high as 1150--1200{degrees}C in one case, during the accident. They concluded that these samples subsequently cooled at a rate of {approx}50--125{degrees}C/min in the temperature range of 600--400{degrees}C, in good agreement with the original analysis. The reviewers also agreed that the remainder of the lower head samples had not exceeded the ferrite-to-austenite transformation temperature during the accident and suggested several refinements and alternative procedures that could have been employed in the original analysis.

Peer review of the Three Mile Island Unit 2 Vessel Investigation Project metallurgical examinations

International Nuclear Information System (INIS)

Bohl, R.W.; Gaydos, R.G.; Vander Voort, G.F.; Diercks, D.R.

1994-07-01

Fifteen samples recovered from the lower head of the Three Mile Island (TMI) Unit 2 nuclear reactor pressure vessel were subjected to detailed metallurgical examinations by the Idaho National Engineering Laboratory (INEL), with supporting work carried out by Argonne National Laboratory (ANL) and several of the European participants. These examinations determined that a portion of the lower head, a so-called elliptical ''hot spot'' measuring ∼0.8 x 1 m, reached temperatures as high as 1100 degrees C during the accident and cooled from these temperatures at ∼10--100 degrees C/min. The remainder of the lower head was found to have remained below the ferrite-toaustenite transformation temperature of 727 degrees C during the accident. Because of the significance of these results and their importance to the overall analysis of the TMI accident, a panel of three outside peer reviewers, Dr. Robert W. Bohl, Mr. Richard G. Gaydos, and Mr. George F. Vander Voort, was formed to conduct an independent review of the metallurgical analyses. After a thorough review of the previous analyses and examination of photo-micrographs and actual lower head specimens, the panel determined that the conclusions resulting from the INEL study were fundamentally correct. In particular, the panel reaffirmed that four lower head samples attained temperatures as high as 1100 degrees C, and perhaps as high as 1150--1200 degrees C in one case, during the accident. They concluded that these samples subsequently cooled at a rate of ∼50--125 degrees C/min in the temperature range of 600--400 degrees C, in good agreement with the original analysis. The reviewers also agreed that the remainder of the lower head samples had not exceeded the ferrite-to-austenite transformation temperature during the accident and suggested several refinements and alternative procedures that could have been employed in the original analysis

An evolving user-oriented model of Internet health information seeking.

Science.gov (United States)

Gaie, Martha J

2006-01-01

This paper presents an evolving user-oriented model of Internet health information seeking (IS) based on qualitative data collected from 22 lung cancer (LC) patients and caregivers. This evolving model represents information search behavior as more highly individualized, complex, and dynamic than previous models, including pre-search psychological activity, use of multiple heuristics throughout the process, and cost-benefit evaluation of search results. This study's findings suggest that IS occurs in four distinct phases: search initiation/continuation, selective exposure, message processing, and message evaluation. The identification of these phases and the heuristics used within them suggests a higher order of complexity in the decision-making processes that underlie IS, which could lead to the development of a conceptual framework that more closely reflects the complex nature of contextualized IS. It also illustrates the advantages of using qualitative methods to extract more subtle details of the IS process and fill in the gaps in existing models.

Evolving Stochastic Learning Algorithm based on Tsallis entropic index

Science.gov (United States)

Anastasiadis, A. D.; Magoulas, G. D.

2006-03-01

In this paper, inspired from our previous algorithm, which was based on the theory of Tsallis statistical mechanics, we develop a new evolving stochastic learning algorithm for neural networks. The new algorithm combines deterministic and stochastic search steps by employing a different adaptive stepsize for each network weight, and applies a form of noise that is characterized by the nonextensive entropic index q, regulated by a weight decay term. The behavior of the learning algorithm can be made more stochastic or deterministic depending on the trade off between the temperature T and the q values. This is achieved by introducing a formula that defines a time-dependent relationship between these two important learning parameters. Our experimental study verifies that there are indeed improvements in the convergence speed of this new evolving stochastic learning algorithm, which makes learning faster than using the original Hybrid Learning Scheme (HLS). In addition, experiments are conducted to explore the influence of the entropic index q and temperature T on the convergence speed and stability of the proposed method.

Mechanical fasteners used in historical Siberian shipbuilding: perspectives for metallurgical analysis

Science.gov (United States)

Goncharov, A. E.; Mednikov, D. M.; Karelin, N. M.; Nasyrov, I. R.

2017-10-01

Recent discoveries of shipwrecked vessels in the northern reaches of the river Yenisei led to a number of questions concerning the history of shipbuilding in Siberia and the technical features of the first vessels of the industrial era to navigate the Northern Sea Route and the Yenisei. One of these questions addresses the features of mechanical fasteners used in the construction of the Siberian vessels. The answer to this question may provide information on how the first vessels, constructed in Siberia during the 1870’s, were able to sail the high seas of the Arctic Ocean and reach European ports. In this paper, we provide a description of iron mechanical fasteners obtained from one shipwrecked vessel and discuss on the perspectives of a metallurgical analysis This research has been funded by a grant of the Russian Fund of Humanities Research (Russian Fund of Fundamental Research) and the Krasnoyarsk Regional Science Fund under Grant number 16-11-24010.

Online monitoring of corrosion behavior in molten metal using laser-induced breakdown spectroscopy

Science.gov (United States)

Zeng, Qiang; Pan, Congyuan; Li, Chaoyang; Fei, Teng; Ding, Xiaokang; Du, Xuewei; Wang, Qiuping

2018-04-01

The corrosion behavior of structure materials in direct contact with molten metals is widespread in metallurgical industry. The corrosion of casting equipment by molten metals is detrimental to the production process, and the corroded materials can also contaminate the metals being produced. Conventional methods for studying the corrosion behavior by molten metal are offline. This work explored the application of laser-induced breakdown spectroscopy (LIBS) for online monitoring of the corrosion behavior of molten metal. The compositional changes of molten aluminum in crucibles made of 304 stainless steel were obtained online at 1000 °C. Several offline techniques were combined to determine the corrosion mechanism, which was highly consistent with previous studies. Results proved that LIBS was an efficient method to study the corrosion mechanism of solid materials in molten metal.

3Q/4Q98 Annual M-Area and Metallurgical Laboratory Hazardous Waste Management Facility Groundwater Monitoring and Correction-Action Report, Volumes I, II, and III

International Nuclear Information System (INIS)

Chase, J.

1999-01-01

This report describes the groundwater monitoring and corrective-action program at the M-Area Hazardous Waste Management Facility (HWMF) and the Metallurgical Laboratory (Met Lab) HWMF at the Savannah River Site (SRS) during 1998

Quasispecies-like behavior observed in catalytic RNA populations evolving in a test tube

Directory of Open Access Journals (Sweden)

Lehman Niles

2010-03-01

Full Text Available Abstract Background During the RNA World, molecular populations were probably very small and highly susceptible to the force of strong random drift. In conjunction with Muller's Ratchet, this would have imposed difficulties for the preservation of the genetic information and the survival of the populations. Mechanisms that allowed these nascent populations to overcome this problem must have been advantageous. Results Using continuous in vitro evolution experimentation with an increased mutation rate imposed by MnCl2, it was found that clonal 100-molecule populations of ribozymes clearly exhibit certain characteristics of a quasispecies. This is the first time this has been seen with a catalytic RNA. Extensive genotypic sampling from two replicate lineages was gathered and phylogenetic networks were constructed to elucidate the structure of the evolving RNA populations. A common distribution was found in which a mutant sequence was present at high frequency, surrounded by a cloud of mutant with lower frequencies. This is a typical distribution of quasispecies. Most of the mutants in these clouds were connected by short Hamming distance values, indicating their close relatedness. Conclusions The quasispecies nature of mutant RNA clouds facilitates the recovery of genotypes under pressure of being removed from the population by random drift. The empirical populations therefore evolved a genotypic resiliency despite a high mutation rate by adopting the characteristics of quasispecies, implying that primordial RNA pools could have used this strategy to avoid extinction.

On sexual behavior and sex-role reversal.

Science.gov (United States)

Schuiling, Gerard A

2005-09-01

Sex is not about reproduction; sex is about (re-)combination of DNA. Sex, not reproduction, always involves physical contact between two individuals; to achieve this, strategies of sexual behavior evolved. Sexual behavior, therefore, did not evolve as part of a reproductive strategy, but evolved to enable exchange of genetic material. In multicellular organisms the situation is more complicated than in unicellular organisms, as it is impossible for each cell within a multicellular body to have sex with another cell. Hence, evolution selected a system in which the possibility to have sex was limited to only one cell-line: the germ cells. As a result, sex adopted the character of fertilization, and sex and reproduction became inseparably linked. Still, in some species, including humans, sexual behavior still exhibits features of its evolutionary past: in humans (like in bonobo's) most sexual activity and many sexual behavioral patterns have nothing to do with reproduction (masturbation, homosexual behavior, for example); in humans, sexual behavior also became associated with other strategic objectives, such as intensifying the pair bond, expression of love or power. Different genders - male and female - evolved, and each gender evolved typical gender-related sexual and reproductive strategies as well. In most multicellular species, these strategies became inextricably mixed, and sexual behavior increasingly more - and in most species even exclusively - 'served' the interests of reproduction: sexual behavior became more or less synonymous with reproductive behavior. In most species, the 'mix' of sexual and reproductive strategies evolved into typical gender-related patterns of behavior, that is, in typical 'sex-roles'. Often, males are bigger and more 'beautiful' (= more intensely ornamented) than females; males compete with each other for access to females; males court females, while females choose males ('female choice'). However, ecological circumstances may cause

Evolvability Is an Evolved Ability: The Coding Concept as the Arch-Unit of Natural Selection.

Science.gov (United States)

Janković, Srdja; Ćirković, Milan M

2016-03-01

Physical processes that characterize living matter are qualitatively distinct in that they involve encoding and transfer of specific types of information. Such information plays an active part in the control of events that are ultimately linked to the capacity of the system to persist and multiply. This algorithmicity of life is a key prerequisite for its Darwinian evolution, driven by natural selection acting upon stochastically arising variations of the encoded information. The concept of evolvability attempts to define the total capacity of a system to evolve new encoded traits under appropriate conditions, i.e., the accessible section of total morphological space. Since this is dependent on previously evolved regulatory networks that govern information flow in the system, evolvability itself may be regarded as an evolved ability. The way information is physically written, read and modified in living cells (the "coding concept") has not changed substantially during the whole history of the Earth's biosphere. This biosphere, be it alone or one of many, is, accordingly, itself a product of natural selection, since the overall evolvability conferred by its coding concept (nucleic acids as information carriers with the "rulebook of meanings" provided by codons, as well as all the subsystems that regulate various conditional information-reading modes) certainly played a key role in enabling this biosphere to survive up to the present, through alterations of planetary conditions, including at least five catastrophic events linked to major mass extinctions. We submit that, whatever the actual prebiotic physical and chemical processes may have been on our home planet, or may, in principle, occur at some time and place in the Universe, a particular coding concept, with its respective potential to give rise to a biosphere, or class of biospheres, of a certain evolvability, may itself be regarded as a unit (indeed the arch-unit) of natural selection.

Assessing market structures in resource markets. An empirical analysis of the market for metallurgical coal using various equilibrium models

Energy Technology Data Exchange (ETDEWEB)

Lorenczik, Stefan; Panke, Timo [Koeln Univ. (Germany). Inst. of Energy Economics

2015-05-15

The prevalent market structures found in many resource markets consist of a high concentration on the supply side and a low demand elasticity. Market results are therefore frequently assumed to be an outcome of strategic interaction between producers. Common models to investigate the market outcomes and underlying market structures are games representing competitive markets, strategic Cournot competition and Stackelberg structures taking into account a dominant player acting first followed by one or more followers. Besides analysing a previously neglected scenario of the latter kind, we add to the literature by expanding the application of mathematical models by applying an Equilibrium Problem with Equilibrium Constraints (EPEC), which is used to model multi-leader-follower games, to a spatial market. We apply our model by investigating the prevalent market setting in the international market for metallurgical coal between 2008 and 2010, whose market structure provides arguments for a wide variety of market structures. Using different statistical measures and comparing model with actual market outcomes, we find that two previously neglected settings perform best: First, a setting in which the four largest metallurgical coal exporting firms compete against each other as Stackelberg leaders, while the remainders act as Cournot followers. Second, a setting with BHPB acting as sole Stackelberg leader.

Assessing market structures in resource markets. An empirical analysis of the market for metallurgical coal using various equilibrium models

International Nuclear Information System (INIS)

Lorenczik, Stefan; Panke, Timo

2015-01-01

The prevalent market structures found in many resource markets consist of a high concentration on the supply side and a low demand elasticity. Market results are therefore frequently assumed to be an outcome of strategic interaction between producers. Common models to investigate the market outcomes and underlying market structures are games representing competitive markets, strategic Cournot competition and Stackelberg structures taking into account a dominant player acting first followed by one or more followers. Besides analysing a previously neglected scenario of the latter kind, we add to the literature by expanding the application of mathematical models by applying an Equilibrium Problem with Equilibrium Constraints (EPEC), which is used to model multi-leader-follower games, to a spatial market. We apply our model by investigating the prevalent market setting in the international market for metallurgical coal between 2008 and 2010, whose market structure provides arguments for a wide variety of market structures. Using different statistical measures and comparing model with actual market outcomes, we find that two previously neglected settings perform best: First, a setting in which the four largest metallurgical coal exporting firms compete against each other as Stackelberg leaders, while the remainders act as Cournot followers. Second, a setting with BHPB acting as sole Stackelberg leader.

Natural selection promotes antigenic evolvability

NARCIS (Netherlands)

Graves, C.J.; Ros, V.I.D.; Stevenson, B.; Sniegowski, P.D.; Brisson, D.

2013-01-01

The hypothesis that evolvability - the capacity to evolve by natural selection - is itself the object of natural selection is highly intriguing but remains controversial due in large part to a paucity of direct experimental evidence. The antigenic variation mechanisms of microbial pathogens provide

Corrosion behaviour of hyper duplex stainless steel in various metallurgical conditions for sea water cooled condensers

International Nuclear Information System (INIS)

Singh, Umesh Pratap; Kain, Vivekanand; Chandra, Kamlesh

2011-01-01

The sea water cooled condensers have to resist severe corrosion as marine environment is the most corrosive natural environment. Copper alloys are being phased out due to difficulties in water chemistry control and Titanium base alloys are extremely expensive. Austenitic stainless steels (SS) remain prone to localized corrosion in marine environments hence not suitable. These heat exchangers operate at temperatures not exceeding 50 deg C and at very low pressures. The tubes of these heat exchangers are joined to the carbon steel tube sheets by roll expansion or by roll expansion followed by seam welding. These conditions are expected to affect the localized corrosion resistance of the tube in roll joined region due to cold working and in the tube-tube sheet welded joint due to thermal effects of welding. In this study, the localized corrosion behaviour of a Hyper Duplex Stainless Steel (HDSS) has been evaluated, and compared with other materials e.g. types 304L SS, 316L SS, Duplex SS 2205, Titanium grade - 2, and Al Brass. The evaluation is done in three metallurgical conditions (a) as received, (b) cold rolled and (c) welded condition in synthetic sea water at room temperature and at 50 deg C to assess the resistance to crevice, pitting and stress corrosion cracking using standard ASTM exposure and electrochemical techniques. The results provide comparative assessment of these alloys and show their susceptibility in the three metallurgical conditions as encountered in condensers. Hyper-duplex SS has been shown to be highly resistant in sea water for the condenser tubing application. (author)

Occupational exposure to PCDDs, PCDFs, and PCBs of metallurgical workers in some industrial plants of the Brescia area, northern Italy.

Science.gov (United States)

Abballe, Annalisa; Barbieri, Pietro Gino; di Domenico, Alessandro; Garattini, Siria; Iacovella, Nicola; Ingelido, Anna Maria; Marra, Valentina; Miniero, Roberto; Valentini, Silvia; De Felip, Elena

2013-01-01

The study was carried out in order to respond to public concern on the occupational exposure of metallurgical workers to highly toxic PCDDs, PCDFs, and PCBs in the area of the city of Brescia, northern Italy. The study investigated the effects on the haematic burden of occupational exposures to the aforesaid contaminants in different work environments, attempting to establish causal relationships and providing indications for occupational health preventive measures. Chemical concentrations were measured in blood serum of "professionally exposed" (PE) and "not professionally exposed" (NPE) subjects. NPE subjects included industrial administrative employees, Brescia inhabitants, and remote rural people. The central tendency indexes of contaminant cumulative concentrations were higher in PE than in NPE samples (for the mean values: PCDDs+PCDFs, 22.9 vs. 19.5 pgWHO-TEQ(1997)/g lb; DL-PCBs, 26.0 vs. 23.6 pgWHO-TEQ(1997)/g lb; PCDDs+PCDFs+DL-PCBs (TEQ(TOT)), 48.9 vs. 43.1 pgWHO-TEQ(1997)/g lb; Σ(6)[NDL-PCBs], 427 vs. 401 ng g(-1)lb); however, no statistical differences were detected at P=0.05. A significant difference for PCDDs+PCDFs and TEQ(TOT) was observed as the NPE data were progressively reduced to those of the remote rural people. The existence of a differential occupational exposure due to different environments was detected by applying the factor analysis to congener-specific data (analytical profiles). Findings indicate that metallurgical workers may be exposed to PCDD, PCDF, and PCB more than the general population, in particular due to non-negligible contributions to exposure from workplace ambient air. Findings also suggest that an improvement of preventive measures may be required to avoid chemical overexposure in certain metallurgical workplaces. To identify exposure groups, the DL- and NDL-PCB analytical profiles seemed to be more sensitive to environmental exposure sources/pathways than those of PCDDs and PCDFs. Copyright © 2012 Elsevier Ltd. All

The history of decisions on creation of nuclear and metallurgical complex on the basis of the Kola nuclear power plant

Directory of Open Access Journals (Sweden)

Kudrin B. I.

2017-02-01

Full Text Available Some reasons for the choice of directions for using electric and thermal energy of the Kola nuclear power plant located beyond the Arctic Circle have been presented. The regions of the country and their large-scale industrial productions based on metallurgical enterprises have been indicated; the electrical supply of these enterprises is implemented from the Kola NPP. The results of research of energy inputs for the production of a ton of steel and cast iron have been presented. It has been determined that the main direction of technological modernization in the steel industry is avoiding the use of organic fuels (particularly in coke-blast furnace production as the most energy-intensive and its replacement with the technology of direct reduction of iron with hydrogen. As an alternative energy source for organic fuels the creation of a fuel-free nuclear-metallurgical electrified complex has been proposed. The principal scheme of the fuel-free nuclear-metallurgical electrified complex has been described, here the main novelty has a reducing gases preparation block giving the potential ability for creating waste-free process. It has been noted that this technology requires using high temperatures and solving technical problems related to heat resistance of constructions. Some examples of world research on the implementation of similar projects have been presented. It has been determined that the use of new technology will cause the need for optimization of power consumption structure due to the redistribution of capacity and electrical consumption between productions. The introduction of new technologies requires solving a number of problems on electric power supply and electrical equipment designing. It has been observed that on the Kola NPP large-scale reconstruction was carried out during the working period, it helped to increase its project capacity and extend the operation life. Nowadays the region has excess installed capacity that can be

Advances in refractories for the metallurgical industries III: proceedings of the international symposium

Energy Technology Data Exchange (ETDEWEB)

Allaire, C.; Rigaud, M. [eds.] [Ecole Polytchnique, Montreal, PQ (Canada)

1999-07-01

In the three years since the last symposium key innovations have been made in the penetration of monoliths in all sectors of the metallurgical industries. The symposium was presented within the 38th Annual Conference of Metallurgists of the Canadian Institute of Mining, Metallurgy and Petroleum. Broad international coverage was maintained with papers originating from 12 different countries including: Australia, Canada, China, France, Germany, India, Iran, Japan, Korea, Mexico, New Zealand, Norway, and the United States. The 27 papers presented are divided into seven sessions to reflect the interests of the participants. The sessions included mold fluxes I and II, aluminum refractories, alumina castables, andalusite castables, continuous casting of refractories, aluminum refractories II and copper-nickel refineries. One paper on refractories for exhaust gas scrubbers is abstracted separately.

The antiquity and evolutionary history of social behavior in bees.

Directory of Open Access Journals (Sweden)

Sophie Cardinal

Full Text Available A long-standing controversy in bee social evolution concerns whether highly eusocial behavior has evolved once or twice within the corbiculate Apidae. Corbiculate bees include the highly eusocial honey bees and stingless bees, the primitively eusocial bumble bees, and the predominantly solitary or communal orchid bees. Here we use a model-based approach to reconstruct the evolutionary history of eusociality and date the antiquity of eusocial behavior in apid bees, using a recent molecular phylogeny of the Apidae. We conclude that eusociality evolved once in the common ancestor of the corbiculate Apidae, advanced eusociality evolved independently in the honey and stingless bees, and that eusociality was lost in the orchid bees. Fossil-calibrated divergence time estimates reveal that eusociality first evolved at least 87 Mya (78 to 95 Mya in the corbiculates, much earlier than in other groups of bees with less complex social behavior. These results provide a robust new evolutionary framework for studies of the organization and genetic basis of social behavior in honey bees and their relatives.

The behaviour of Pacific metallurgical coal markets: the impact of Japan's acquisition strategy on market price

Energy Technology Data Exchange (ETDEWEB)

Koerner, R J [Queensland University, St. Lucia, Qld. (Australia). Graduate School of Management, Faculty of Commerce and Economics

1993-03-01

This paper examines whether some elements of Japan's resource acquisition strategies might have caused price and other distortions of market behaviour in the Pacific metallurgical coal trade. The industry chosen for investigation is that of steel manufacture, and the traded resources commodity examined is coking coal, which is the primary energy input for blast furnace iron making. Regression modelling studies to determine historic acquisition value and quality relationships for US, Australian and Canadian coals sold into the Japanese coking coal market are described. Departures from normal demand response behaviour to price competitiveness are also investigated. 3 figs., 3 tabs.

Effects of various tool pin profiles on mechanical and metallurgical properties of friction stir welded joints of cryorolled AA2219 aluminium alloy

Science.gov (United States)

Kamal Babu, Karupannan; Panneerselvam, Kavan; Sathiya, Paulraj; Noorul Haq, Abdul Haq; Sundarrajan, Srinivasan; Mastanaiah, Potta; Srinivasa Murthy, Chunduri Venkata

2018-02-01

Friction stir welding (FSW) process was conducted on cryorolled (CR) AA2219 plate using different tool pin profiles such as cylindrical pin, threaded cylindrical pin, square pin and hexagonal pin profiles. The FSW was carried out with pairs of 6 mm thick CR aluminium plates with different tool pin profiles. The different tool pin profile weld portions' behaviors like mechanical (tensile strength, impact and hardness) and metallurgical characteristics were analyzed. The results of the mechanical analysis revealed that the joint made by the hexagonal pin tool had good strength compared to other pin profiles. This was due to the pulsating action and material flow of the tool resulting in dynamic recrystallization in the weld zone. This was confirmed by the ultra fine grain structure formation in Weld Nugget (WN) of hexagonal pin tool joint with a higher percentage of precipitate dissolution. The fractograph of the hexagonal tool pin weld portion confirmed the finer dimple structure morphology without having any interior defect compared to other tool pin profiles. The lowest weld joint strength was obtained from cylindrical pin profile weld joint due to insufficient material flow during welding. The Transmission Electron Microscope and EDX analysis showed the dissolution of the metastable θ″, θ' (Al2Cu) partial precipitates in the WN and proved the influence of metastable precipitates on enhancement of mechanical behavior of weld. The XRD results also confirmed the Al2Cu precipitation dissolution in the weld zone.

Disgust: Evolved function and structure

NARCIS (Netherlands)

Tybur, J.M.; Lieberman, D.; Kurzban, R.; DeScioli, P.

2013-01-01

Interest in and research on disgust has surged over the past few decades. The field, however, still lacks a coherent theoretical framework for understanding the evolved function or functions of disgust. Here we present such a framework, emphasizing 2 levels of analysis: that of evolved function and

Atomic absorption determination of vanadium in products of metallurgical production and mineral feed stock

International Nuclear Information System (INIS)

Polikarpova, N.V.; Panteleeva, E.Yu.

1983-01-01

Rapid and selective method of atomic absorption determination of vanadium in metallurgical process products and numerical feed stock is suggested. Buffering mixture of aluminium and phosphoric acid is used to suppress the effect of sample composition on the value of vanadium atomic absorption. The concentration of buffer components can vary from 400 up to 2000 μg/ml Al and from 2 up to 5% vol. H 3 PO 4 . The suggested mixture completely eli-- minates the strong chromium effect. The developed method was used for analyzing steels, alloys based on Mo, Ni, Ti, Cr, as well as titanium magnetite ores and concentrates. The method enables to determine from 0.05 up to 10% vanadium with 0.05-0.01 relative standard deviation, respectively

Evolving the use of peptides as biomaterials components

Science.gov (United States)

Collier, Joel H.; Segura, Tatiana

2012-01-01

This manuscript is part of a debate on the statement that “the use of short synthetic adhesion peptides, like RGD, is the best approach in the design of biomaterials that guide cell behavior for regenerative medicine and tissue engineering”. We take the position that although there are some acknowledged disadvantages of using short peptide ligands within biomaterials, it is not necessary to discard the notion of using peptides within biomaterials entirely, but rather to reinvent and evolve their use. Peptides possess advantageous chemical definition, access to non-native chemistries, amenability to de novo design, and applicability within parallel approaches. Biomaterials development programs that require such aspects may benefit from a peptide-based strategy. PMID:21515167

Phosphorus Diffusion Gettering Efficacy in Upgraded Metallurgical-Grade Solar Silicon

Science.gov (United States)

Jiménez, A.; del Cañizo, C.; Cid, C.; Peral, A.

2018-05-01

In the context of the continuous price reduction in photovoltaics (PV) in recent years, Si feedstock continues to be a relevant component in the cost breakdown of a PV module, highlighting the need for low-cost, low-capital expenditure (CAPEX) silicon technologies to further reduce this cost component. Upgraded metallurgical-grade silicon (UMG Si) has recently received much attention, improving its quality and even attaining, in some cases, solar cell efficiencies similar to those of conventional material. However, some technical challenges still have to be addressed when processing this material to compensate efficiently for the high content of impurities and contaminants. Adaptation of a conventional solar cell process to monocrystalline UMG Si wafers has been studied in this work. In particular, a tailored phosphorus diffusion gettering step followed by a low-temperature anneal at 700°C was implemented, resulting in enhanced bulk lifetime and emitter recombination properties. In spite of the need for further research and material optimization, UMG Si wafers were successfully processed, achieving efficiencies in the range of 15% for a standard laboratory solar cell process with aluminum back surface field.

Cyclic fatigue resistance, torsional resistance, and metallurgical characteristics of M3 Rotary and M3 Pro Gold NiTi files

Science.gov (United States)

2018-01-01

Objectives To evaluate the mechanical properties and metallurgical characteristics of the M3 Rotary and M3 Pro Gold files (United Dental). Materials and Methods One hundred and sixty new M3 Rotary and M3 Pro Gold files (sizes 20/0.04 and 25/0.04) were used. Torque and angle of rotation at failure (n = 20) were measured according to ISO 3630-1. Cyclic fatigue resistance was tested by measuring the number of cycles to failure in an artificial stainless steel canal (60° angle of curvature and a 5-mm radius). The metallurgical characteristics were investigated by differential scanning calorimetry. Data were analyzed using analysis of variance and the Student-Newman-Keuls test. Results Comparing the same size of the 2 different instruments, cyclic fatigue resistance was significantly higher in the M3 Pro Gold files than in the M3 Rotary files (p Rotary files showed 1 small peak on the heating curve and 1 small peak on the cooling curve. Conclusions The M3 Pro Gold files showed greater flexibility and angular rotation than the M3 Rotary files, without decrement of their torque resistance. The superior flexibility of M3 Pro Gold files can be attributed to their martensite phase. PMID:29765904

Metallurgical and Mechanical Evaluation of 4340 Steel Produced by Direct Metal Laser Sintering

Science.gov (United States)

Jelis, Elias; Clemente, Matthew; Kerwien, Stacey; Ravindra, Nuggehalli M.; Hespos, Michael R.

2015-03-01

Direct metal laser sintering (DMLS) was used to produce high-strength low-alloy 4340 steel specimens. Mechanical and metallurgical analyses were performed on the specimens to determine the samples with the highest strengths and the least porosity. The optimal process parameters were thus defined based on the corresponding experimental conditions. Additionally, the effects of fabricating specimens with both virgin and recycled powders were studied. Scanning electron microscopy and electron-dispersive spectroscopy were performed on both types of powders to determine the starting morphology and composition. The initial tensile results are promising, suggesting that DMLS can produce specimens equal in strength to wrought materials. However, there is evidence of cracking on several of the heat-treated tensile specimens that is unexplained. Several theories point to disturbances in the build chamber environment that went undetected while the specimens were being fabricated.

Characteristic and Source of Atmospheric PM10- and PM2.5-bound PAHs in a Typical Metallurgic City Near Yangtze River in China.

Science.gov (United States)

Zhang, Hong; Wang, Ruwei; Xue, Huaqin; Hu, Ruoyu; Liu, Guijian

2018-02-01

The characteristics of atmospheric PM 10 - and PM 2.5 -bound polycyclic aromatic hydrocarbons (PAHs) were investigated in Tongling city, China. Results showed that the total concentrations of PM 10 - and PM 2.5 -bound PAHs exhibited distinct seasonal and spatial variability. The metallurgic sites showed the highest PAH concentrations, which is mainly attributed to the metallurgic activities (mainly copper ore smelting) and coal combustion as the smelting fuel. The rural area showed the lowest concentrations, but exhibited significant increase from summer to autumn. This seasonal fluctuation is mainly caused by the biomass burning at the sites in the harvest season. The diagnostic ratio indicated that the main PAHs sources were vehicle exhausts, coal combustion and biomass burning. The total BaP equivalent concentration (BAP-TEQ) was found to be maximum at DGS site in winter, whereas it was minimum at BGC site in summer. Risk assessment indicates that residential exposure to PAHs in the industrial area, especially in the winter season, may pose a greater inhalation cancer risk than people living in living area and rural area.

Metallurgical Laboratory Hazardous Waste Management Facility groundwater monitoring report. First quarter 1995

International Nuclear Information System (INIS)

1995-06-01

During first quarter 1995, samples from AMB groundwater monitoring wells at the Metallurgical Laboratory Hazardous Waste Management Facility (Met Lab HWMF) were analyzed for selected heavy metals, field measurements, radionuclides, volatile organic compounds, and other constituents. Six parameters exceeded standards during the quarter. As in previous quarters, tetrachloroethylene and trichloroethylene exceeded final Primary Drinking Water Standards (PDWS). Total organic halogens exceeded its Savannah River Site (SRS) Flag 2 criterion during first quarter 1995 as in fourth quarter 1994. Aluminum, iron, and manganese, which were not analyzed for during fourth quarter 1994, exceeded the Flag 2 criteria in at least two wells each during first quarter 1995. Groundwater flow direction and rate in the M-Area Aquifer Zone were similar to previous quarters. Conditions affecting the determination of groundwater flow directions and rates in the Upper Lost Lake Aquifer Zone, Lower Lost Lake Aquifer Zone, and the Middle Sand Aquifer Zone of the Crouch Branch Confining Unit were also similar to previous quarters

Behavioral responses in structured populations pave the way to group optimality.

Science.gov (United States)

Akçay, Erol; Van Cleve, Jeremy

2012-02-01

An unresolved controversy regarding social behaviors is exemplified when natural selection might lead to behaviors that maximize fitness at the social-group level but are costly at the individual level. Except for the special case of groups of clones, we do not have a general understanding of how and when group-optimal behaviors evolve, especially when the behaviors in question are flexible. To address this question, we develop a general model that integrates behavioral plasticity in social interactions with the action of natural selection in structured populations. We find that group-optimal behaviors can evolve, even without clonal groups, if individuals exhibit appropriate behavioral responses to each other's actions. The evolution of such behavioral responses, in turn, is predicated on the nature of the proximate behavioral mechanisms. We model a particular class of proximate mechanisms, prosocial preferences, and find that such preferences evolve to sustain maximum group benefit under certain levels of relatedness and certain ecological conditions. Thus, our model demonstrates the fundamental interplay between behavioral responses and relatedness in determining the course of social evolution. We also highlight the crucial role of proximate mechanisms such as prosocial preferences in the evolution of behavioral responses and in facilitating evolutionary transitions in individuality.

CFD Analyses of Re-Evolved Iodine from an In-containment Water Pool

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae Hyeon [KHNP CRI, Daejeon (Korea, Republic of); Yoon, Woo Sung; Jung, Ji Hwan [Pusan National University, Busan (Korea, Republic of)

2016-10-15

A good understanding of the behavior of iodine is required to evaluate the safety and emergency procedures after a LOCA. The quantity of re-evolved iodine is related to pH level, temperature, and iodine concentration of water pool. In the calculation of pH for water pool, sequence calculations must consider this variable if any aqueous iodine is present, even if it is initially present in stable forms. The present study consists of two parts: the pH evaluation and the evaluation of the iodine re-evolution. The current paper focuses on the pH evaluation method, the development of a user-defined function (UDF) and the iodine re-evolution from the water pool. CFD that incorporates the UDF was used in this study to calculate the local pH level in the transient condition. The amount of re-evolved iodine was calculated based on the iodine concentration, temperature, and pH. The transportation and resulting distribution of the iodine concentration, temperature, and pH were calculated using transient analyses with CFD. The quantity of reevolved iodine was obtained with several assumptions. The quantitative evaluation of re-evolved iodine during a LOCA in a commercial nuclear power plants is done in two stages. The first stage is to calculate the pH in the water pool, and the second stage is to calculate the quantity of re-evolved iodine. Evaporated iodine, from the water pool water to the containment atmosphere, can be estimated from characteristic iodine behaviors and pH calculations. The 3D CFD analysis results show that the pH reached 7.0 after 149.5 minutes. Near the spillway, the change in averaged pH was faster than the change in wholevolume averaged pH. Evaluating the amount of reevolved iodine were examined using four different methods. As a result of our evaluation of iodine reevolution, the initial molecular iodine concentration of a water pool has a significant impact on the amount of gaseous iodine, more so than the pH or temperature, due to the locally similar

CFD Analyses of Re-Evolved Iodine from an In-containment Water Pool

International Nuclear Information System (INIS)

Kim, Tae Hyeon; Yoon, Woo Sung; Jung, Ji Hwan

2016-01-01

A good understanding of the behavior of iodine is required to evaluate the safety and emergency procedures after a LOCA. The quantity of re-evolved iodine is related to pH level, temperature, and iodine concentration of water pool. In the calculation of pH for water pool, sequence calculations must consider this variable if any aqueous iodine is present, even if it is initially present in stable forms. The present study consists of two parts: the pH evaluation and the evaluation of the iodine re-evolution. The current paper focuses on the pH evaluation method, the development of a user-defined function (UDF) and the iodine re-evolution from the water pool. CFD that incorporates the UDF was used in this study to calculate the local pH level in the transient condition. The amount of re-evolved iodine was calculated based on the iodine concentration, temperature, and pH. The transportation and resulting distribution of the iodine concentration, temperature, and pH were calculated using transient analyses with CFD. The quantity of reevolved iodine was obtained with several assumptions. The quantitative evaluation of re-evolved iodine during a LOCA in a commercial nuclear power plants is done in two stages. The first stage is to calculate the pH in the water pool, and the second stage is to calculate the quantity of re-evolved iodine. Evaporated iodine, from the water pool water to the containment atmosphere, can be estimated from characteristic iodine behaviors and pH calculations. The 3D CFD analysis results show that the pH reached 7.0 after 149.5 minutes. Near the spillway, the change in averaged pH was faster than the change in wholevolume averaged pH. Evaluating the amount of reevolved iodine were examined using four different methods. As a result of our evaluation of iodine reevolution, the initial molecular iodine concentration of a water pool has a significant impact on the amount of gaseous iodine, more so than the pH or temperature, due to the locally similar

Neural correlates of dynamically evolving interpersonal ties predict prosocial behavior

NARCIS (Netherlands)

J.J. Fahrenfort (Johannes J.); F.A.A.M. Winden, van (Frans); B. Pelloux (Benjamin); M. Stallen (Mirre); K.R. Ridderinkhof (Richard)

2012-01-01

textabstractThere is a growing interest for the determinants of human choice behavior in social settings. Upon initial contact, investment choices in social settings can be inherently risky, as the degree to which the other person will reciprocate is unknown. Nevertheless, people have been shown to

Neural correlates of dynamically evolving interpersonal ties predict prosocial behavior

NARCIS (Netherlands)

Fahrenfort, J.J.; van Winden, F.A.A.M.; Pelloux, B.; Stallen, M.; Ridderinkhof, K.R.

2012-01-01

There is a growing interest for the determinants of human choice behavior in social settings. Upon initial contact, investment choices in social settings can be inherently risky, as the degree to which the other person will reciprocate is unknown. Nevertheless, people have been shown to exhibit

Nutrient and dissolved organic carbon removal from water using mining and metallurgical by-products.

Science.gov (United States)

Wendling, Laura A; Douglas, Grant B; Coleman, Shandel; Yuan, Zheng

2012-05-15

Excess nutrient input to water bodies frequently results in algal blooms and development of oxygen deficient conditions. Mining or metallurgical by-products can potentially be utilised as filtration media within water treatment systems such as constructed wetlands, permeable reactive barriers, or drain liners. These materials may offer a cost-effective solution for the removal of nutrients and dissolved organic carbon (DOC) from natural waters. This study investigated steel-making, alumina refining (red mud and red sand) and heavy mineral processing by-products, as well as the low-cost mineral-based material calcined magnesia, in laboratory column trials. Influent water and column effluents were analysed for pH and flow rate, alkalinity, nutrient species and DOC, and a range of major cations and anions. In general, by-products with high Ca or Mg, and to a lesser extent those with high Fe content, were well-suited to nutrient and DOC removal from water. Of the individual materials examined, the heavy mineral processing residue neutralised used acid (NUA) exhibited the highest sorption capacity for P, and removed the greatest proportions of all N species and DOC from influent water. In general, NUA and mixtures containing NUA, particularly those with calcined magnesia or red mud/red sand were the most effective in removing nutrients and DOC from influent water. Post-treatment effluents from columns containing NUA and NUA/steel-making by-product, NUA/red sand and NUA/calcined magnesia mixtures exhibited large reductions in DOC, P and N concentrations and exhibited a shift in nutrient ratios away from potential N- and Si-limitation and towards potential P-limitation. If employed as part of a large-scale water treatment scheme, use of these mining and metallurgical by-products for nutrient removal could result in reduced algal biomass and improved water quality. Identification and effective implementation of mining by-products or blends thereof in constructed wetlands

A neighbourhood evolving network model

International Nuclear Information System (INIS)

Cao, Y.J.; Wang, G.Z.; Jiang, Q.Y.; Han, Z.X.

2006-01-01

Many social, technological, biological and economical systems are best described by evolved network models. In this short Letter, we propose and study a new evolving network model. The model is based on the new concept of neighbourhood connectivity, which exists in many physical complex networks. The statistical properties and dynamics of the proposed model is analytically studied and compared with those of Barabasi-Albert scale-free model. Numerical simulations indicate that this network model yields a transition between power-law and exponential scaling, while the Barabasi-Albert scale-free model is only one of its special (limiting) cases. Particularly, this model can be used to enhance the evolving mechanism of complex networks in the real world, such as some social networks development

Evolved H II regions

International Nuclear Information System (INIS)

Churchwell, E.

1975-01-01

A probable evolutionary sequence of H II regions based on six distinct types of observed objects is suggested. Two examples which may deviate from this idealized sequence, are discussed. Even though a size-mean density relation of H II regions can be used as a rough indication of whether a nebula is very young or evolved, it is argued that such a relation is not likely to be useful for the quantitative assignment of ages to H II regions. Evolved H II regions appear to fit into one of four structural types: rings, core-halos, smooth structures, and irregular or filamentary structures. Examples of each type are given with their derived physical parameters. The energy balance in these nebulae is considered. The mass of ionized gas in evolved H II regions is in general too large to trace the nebula back to single compact H II regions. Finally, the morphological type of the Galaxy is considered from its H II region content. 2 tables, 2 figs., 29 refs

Effect of groove design on mechanical and metallurgical properties of quenched and tempered low alloy abrasion resistant steel welded joints

International Nuclear Information System (INIS)

Sharma, Varun; Shahi, A.S.

2014-01-01

Highlights: • Effect of weld groove design on Q and T steel welded joints is investigated. • Groove design influences heat dissipation characteristics of welded joints. • Double-V groove joint possesses maximum yield strength and UTS. • C-groove joint possesses highest impact energy, both at room temperature and 0 °C. • A wide variation in microhardness exists across different zone of the weldments. - Abstract: Experimental investigations were carried out to study the influence of three different groove designs on mechanical and metallurgical properties of 15 mm thick Q and T (quenched and tempered) steel welded joints. Welding heat input variation corresponding to each joint configuration was kept to a minimal such that the objective of investigating, exclusively, the effect of varied weld volume on the mechanical and metallurgical performance of these joints could be accomplished. Mechanical performance of these joints was evaluated by subjecting them to transverse tensile testing, and Charpy V-notch impact testing of the weld zones at room temperature and 0 °C. The results of this study reveal that among all types of groove formations used for welding, double-V groove joint possessed maximum YS (yield strength) and UTS (ultimate tensile strength), besides maximum strength ratio (YS/UTS) that was followed by U-groove joint and C-groove joint, respectively. However, weld zone tested individually, for the cover as well as the root pass of the C-groove joint possessed highest CVN (Charpy V-notch) values, both at room temperature and 0 °C. Extensive microhardness studies of these weldments showed a wide variation in the microhardness values of the weld zone and the HAZ (heat affected zone). It was concluded that each groove formation/design exerted a significant influence on the heat dissipation characteristics of these joints, which is evident from different morphological features as revealed through optical microscopy. Scanning electron microscopic

Thermal and Evolved Gas Behavior of Calcite Under Mars Phoenix TEGA Operating Conditions

Science.gov (United States)

Ming, D.W.; Niles, P.B.; Morris, R.V.; Boynton, W.V.; Golden, D.C.; Lauer, H.V.; Sutter, B.

2009-01-01

The Mars Phoenix Scout Mission with its diverse instrument suite successfully examined several soils on the Northern plains of Mars. The Thermal and Evolved Gas Analyzer (TEGA) was employed to detect organic and inorganic materials by coupling a differential scanning calorimeter (DSC) with a magnetic-sector mass spectrometer (MS). Martian soil was heated up to 1000 C in the DSC ovens and evolved gases from mineral decomposition products were examined with the MS. TEGA s DSC has the capability to detect endothermic and exothermic reactions during heating that are characteristic of minerals present in the Martian soil. Initial TEGA results indicated the presence of endothermic peaks with onset temperatures that ranged from 675 C to 750 C with corresponding CO2 release. This result suggests the presence of calcite (CaCO3. CaO + CO2). Organic combustion to CO2 is not likely since this mostly occurs at temperatures below 550 C. Fe-carbonate and Mg-carbonate are not likely because their decomposition temperatures are less than 600 C. TEGA enthalpy determinations suggest that calcite, may occur in the Martian soil in concentrations of approx.1 to 5 wt. %. The detection of calcite could be questioned based on previous results that suggest Mars soils are mostly acidic. However, the Phoenix landing site soil pH was measured at pH 8.3 0.5, which is typical of terrestrial soils where pH is controlled by calcite solubility. The range of onset temperatures and calcite concentration as calculated by TEGA is poorly con-strained in part because of limited thermal data of cal-cite at reduced pressures. TEGA operates at calcite literature thermal data was obtained at 1000 mbar or higher pressures.

The ecology of collective behavior.

Directory of Open Access Journals (Sweden)

Deborah M Gordon

2014-03-01

Full Text Available Similar patterns of interaction, such as network motifs and feedback loops, are used in many natural collective processes, probably because they have evolved independently under similar pressures. Here I consider how three environmental constraints may shape the evolution of collective behavior: the patchiness of resources, the operating costs of maintaining the interaction network that produces collective behavior, and the threat of rupture of the network. The ants are a large and successful taxon that have evolved in very diverse environments. Examples from ants provide a starting point for examining more generally the fit between the particular pattern of interaction that regulates activity, and the environment in which it functions.

GEOLOGY OF THE FLORENCIA GOLD – TELLURIDE DEPOSIT (CAMAGÜEY, CUBA AND SOME METALLURGICAL CONSIDERATIONS

Directory of Open Access Journals (Sweden)

López K Jesús M.

2006-12-01

Full Text Available This paper describes the results from a study of the Florencia gold-telluride deposit in Central Cuba, including mineralogical, petrographical, microprobe and chemical analysis. Valuable information is provided for the exploration, mining and processing of gold ores from other nearby deposits with similar characteristics. Results highlight changes in the mineralogical composition of the ores between the north and south sectors of the deposit, as reflected in metallurgical concentrates after beneficiation and flotation of samples from these sectors.
It is shown that gold deposits of the Cretaceous Volcanic Arc of Cuba largely consist of native gold, telluride and pyrite, where arsenopyrite is almost absent. Traces of lead, zinc and cadmium are present in the periphery of the main ore zones.

(Non-) behavioral economics: a programmatic assessment

OpenAIRE

Güth, Werner

2007-01-01

Economic theory has evolved without paying proper attention to behavioral approaches, especially to social, economic, and cognitive psychology. This has recently changed by including behavioral economics courses in many doctoral study programs. Although this new development is most welcome, the typical topics of the behavioral economics courses are not truly behavioral. More specifically, we question whether neoclassical repairs or game fitting exercises as well as more or less mechanic adapt...

ALTERNATIVE BINDERS TO BENTONITE FOR IRON ORE PELLETIZING : PART II : EFFECTS ON METALLURGICAL AND CHEMICAL PROPERTIES

Directory of Open Access Journals (Sweden)

Osman Sivrikaya

2014-07-01

Full Text Available This study was started to find alternative binders to bentonite and to recover the low preheated and fired pellet mechanical strengths of organic binders-bonded pellets. Bentonite is considered as a chemical impurity for pellet chemistry due to acid constituents (SiO2 and Al2O3. Especially addition of silica-alumina bearing binders is detrimental for iron ore concentrate with high acidic content. Organic binders are the most studied binders since they are free in silica. Although they yield pellets with good wet strength; they have found limited application in industry since they fail to give sufficient physical and mechanical strength to preheated and fired pellets. It is investigated that how insufficient preheated and fired pellet strengths can be improved when organic binders are used as binder. The addition of a slag bonding/strength increasing constituent (free in acidic contents into pellet feed to provide pellet strength with the use of organic binders was proposed. Addition of boron compounds such as colemanite, tincal, borax pentahydrate, boric acid together with organic binders such as CMC, starch, dextrin and some organic based binders, into magnetite and hematite pellet mixture was tested. After determining the addition of boron compounds is beneficial to recover the low pellet physical and mechanical qualities in the first part of this study, in this second part, metallurgical and chemical properties (reducibility - swelling index – microstructure – mineralogy - chemical content of pellets produced with combined binders (an organic binder plus a boron compound were presented. The metallurgical and chemical tests results showed that good quality product pellets can be produced with combined binders when compared with the bentonite-bonded pellets. Hence, the suggested combined binders can be used as binder in place of bentonite in iron ore pelletizing without compromising the pellet chemistry.

Utilisation of the binders prepared from coal tar pitch and phenolic resins for the production metallurgical quality briquettes from coke breeze and the study of their high temperature carbonization behaviour

Energy Technology Data Exchange (ETDEWEB)

Benk, Ayse [University of Erciyes, Faculty of Art and Science, Department of Chemistry, 38039, Kayseri (Turkey)

2010-09-15

To reduce the cost of the formed coke briquettes which can be used as a substitute fuel to the metallurgical coke for the blast furnace from the coke breeze alternative binders and their blends were used. The high temperature behavior was investigated. The binders tested were: the nitrogen blown, air blown coal tar pitch and the blend of air blown coal tar pitch with the phenolic resins blends. The phenolic resin blends were prepared by mixing equal amount of resole and novalac. From the results, nitrogen blowing resulted in the weakest briquettes. The air blowing procedure should be preferred in place of nitrogen blowing for this purpose. When the air blown coal tar pitch was used alone as a binder, the briquettes must be cured at 200 C for 2 h, then carbonized at a temperature above 670 C. Since it requires higher temperature at carbonization stage, using air blown coal tar pitch alone as a binder was not economical. Therefore, the briquettes were prepared from the blended binder, containing air blown coal tar pitch and phenolic resins blend. The optimum amount of air blown coal tar pitch was found to be 50% w/w in the blended binder. Curing the briquettes at 200 C for 2 h was found to be sufficient for producing strong briquettes with a tensile strength of 50.45 MN/m{sup 2}. When these cured briquettes were carbonized at temperatures 470 C, 670 C and 950 C, their strength were increasing continuously, reaching to 71.85 MN/m{sup 2} at the carbonization temperature of 950 C. These briquettes can be used as a substitute for the metallurgical coke after curing; the process might not require un-economical high temperature carbonization stage. (author)

Metallurgical Analysis of Cracks Formed on Coal Fired Boiler Tube

Science.gov (United States)

Kishor, Rajat; Kyada, Tushal; Goyal, Rajesh K.; Kathayat, T. S.

2015-02-01

Metallurgical failure analysis was carried out for cracks observed on the outer surface of a boiler tube made of ASME SA 210 GR A1 grade steel. The cracks on the surface of the tube were observed after 6 months from the installation in service. A careful visual inspection, chemical analysis, hardness measurement, detailed microstructural analysis using optical and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy were carried out to ascertain the cause for failure. Visual inspection of the failed tube revealed the presence of oxide scales and ash deposits on the surface of the tube exposed to fire. Many cracks extending longitudinally were observed on the surface of the tube. Bulging of the tube was also observed. The results of chemical analysis, hardness values and optical micrographs did not exhibit any abnormality at the region of failure. However, detailed SEM with EDS analysis confirmed the presence of various oxide scales. These scales initiated corrosion at both the inner and outer surfaces of the tube. In addition, excessive hoop stress also developed at the region of failure. It is concluded that the failure of the boiler tube took place owing to the combined effect of the corrosion caused by the oxide scales as well as the excessive hoop stress.

Applications of Moessbauer spectroscopy to the structural characterization of minerals and products of the country 's mining - metallurgical industry

International Nuclear Information System (INIS)

Herrera Palma, Victoria; Cruz Inclan, Carlos Manuel

2016-01-01

Since the seventies of the past century Moessbauer Spectroscopy (MS) has been systematically and successfully applied at CEADEN in the study and characterization of lateritic and other iron-rich ores, and different products of their industrial processing as well. Due to their high iron and chrome content these materials seemed to be attractive as raw material for the production of several enriched fractions in metallurgical applications. Such studies showed that the systematic application of MS combined with X- Ray Diffraction and other techniques like neutron Diffraction, Thermal and Calorimetric analysis and Optical and Electron Microscopies, has allowed a higher level of accuracy in the crystallographic characterization, and the phase composition and other specific properties assessment. As examples in this direction, in the present paper results of the study on two different iron-bearing materials are reported: a) magnetite of Mina Grande (in Santiago de Cuba), and b) Monitoring of a proposed process using concentration tables for chrome enrichment from tailings of the nickel plant 'Hector Ramos Latour' at Holguin, both areas located in the east of Cuba. It is evidenced that a right combination of 57 Fe Moessbauer Spectroscopy with other mentioned methods is nowadays the wisest and most efficient way for a thorough identification and characterization of iron-bearing mineral ores and products in mining and metallurgical industry. (Author)

Evolving Technologies: A View to Tomorrow

Science.gov (United States)

Tamarkin, Molly; Rodrigo, Shelley

2011-01-01

Technology leaders must participate in strategy creation as well as operational delivery within higher education institutions. The future of higher education--the view to tomorrow--is irrevocably integrated and intertwined with evolving technologies. This article focuses on two specific evolving technologies: (1) alternative IT sourcing; and (2)…

Stationary and nonstationary properties of evolving networks with preferential linkage

International Nuclear Information System (INIS)

Jezewski, W.

2002-01-01

Networks evolving by preferential attachment of both external and internal links are investigated. The rate of adding an external link is assumed to depend linearly on the degree of a preexisting node to which a new node is connected. The process of creating an internal link, between a pair of existing vertices, is assumed to be controlled entirely by the vertex that has more links than the other vertex in the pair, and the rate of creation of such a link is assumed to be, in general, nonlinear in the degree of the more strongly connected vertex. It is shown that degree distributions of networks evolving only by creating internal links display for large degrees a nonstationary power-law decay with a time-dependent scaling exponent. Nonstationary power-law behaviors are numerically shown to persist even when the number of nodes is not fixed and both external and internal connections are introduced, provided that the rate of preferential attachment of internal connections is nonlinear. It is argued that nonstationary effects are not unlikely in real networks, although these effects may not be apparent, especially in networks with a slowly varying mean degree

Roadmap report of the Metallurgical Industry and Foundries [in the Netherlands]; Rapportage Routekaart Metallurgische Industrie en Gieterijen

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-08-15

The roadmap describes the direction VNMI and AVNeG consider as feasible to realize substantial improvements with regard to energy efficiency in metallurgical production processes and in the usage of metal products. The aim of the report is to guide development efforts and describe technical and organizational options for businesses and industries in the metal sector [Dutch] De Routekaart beschrijft de richting die VNMI en AVNeG als haalbaar zien om naar 2030 toe substantiele energie-efficientieverbeteringen te realiseren in metallurgische productieprocessen en in de gebruiksfase van metaal producten. Het rapport is richtinggevend voor ontwikkelingsinspanningen en beschrijft technische en organisatorische mogelijkheden waar bedrijven individueel en in sectorverband zich voor zullen inzetten.

Metallurgical electrochemistry: the interface between materials science and molten salt chemistry

International Nuclear Information System (INIS)

Sadoway, D.R.

1991-01-01

Even though molten salt electrolysis finds application in the primary extraction of metals (electrowinning), the purification and recycling of metals (electrorefining), and in the formation of metal coatings (electroplating), the technology remains in many respects underexploited. Electrolysis in molten salts as well as other nonaqueous media has enormous potential for materials processing. First, owing to the special attributes of nonaqueous electrolytes electrochemical processing in these media has an important role to play in the generation of advanced materials, i.e., materials with specialized chemistries or tailored microstructures (electrosynthesis). Secondly, as environmental quality standards rise beyond the capabilities of classical metals extraction technologies to comply, molten salt electrolysis may prove to be the only acceptable route from ore to metal. Growing public awareness of pollution from the metals industry could stimulate a renaissance in molten salt electrochemistry. Challenges facing metallurgical electrochemistry as relates to the environment fall into two categories: (1) improving existing electrochemical technology, and (2) developing clean electrochemical technology to displace current nonelectrochemical technology. In both instances success hinges upon the discovery of advanced materials and the ecologically sound extraction of metals, the close coupling between materials science and molten salt chemistry is manifest. (author) 6 refs

3Q/4Q99 Annual M-Area and Metallurgical Laboratory Hazardous Waste Management Facilities Groundwater Monitoring and Corrective-Action Report - Third and Fourth Quarters 1999 - Volumes I and II

International Nuclear Information System (INIS)

Chase, J.

2000-01-01

This report describes the groundwater monitoring and corrective-action program at the M-Area Hazardous Waste Management Facility (HWMF) and the Metallurgical Laboratory (Met Lab) HWMF at the Savannah River Site (SRS) during 1999

Spacetimes containing slowly evolving horizons

International Nuclear Information System (INIS)

Kavanagh, William; Booth, Ivan

2006-01-01

Slowly evolving horizons are trapping horizons that are ''almost'' isolated horizons. This paper reviews their definition and discusses several spacetimes containing such structures. These include certain Vaidya and Tolman-Bondi solutions as well as (perturbatively) tidally distorted black holes. Taking into account the mass scales and orders of magnitude that arise in these calculations, we conjecture that slowly evolving horizons are the norm rather than the exception in astrophysical processes that involve stellar-scale black holes

Criticality is an emergent property of genetic networks that exhibit evolvability.

Directory of Open Access Journals (Sweden)

Christian Torres-Sosa

Full Text Available Accumulating experimental evidence suggests that the gene regulatory networks of living organisms operate in the critical phase, namely, at the transition between ordered and chaotic dynamics. Such critical dynamics of the network permits the coexistence of robustness and flexibility which are necessary to ensure homeostatic stability (of a given phenotype while allowing for switching between multiple phenotypes (network states as occurs in development and in response to environmental change. However, the mechanisms through which genetic networks evolve such critical behavior have remained elusive. Here we present an evolutionary model in which criticality naturally emerges from the need to balance between the two essential components of evolvability: phenotype conservation and phenotype innovation under mutations. We simulated the Darwinian evolution of random Boolean networks that mutate gene regulatory interactions and grow by gene duplication. The mutating networks were subjected to selection for networks that both (i preserve all the already acquired phenotypes (dynamical attractor states and (ii generate new ones. Our results show that this interplay between extending the phenotypic landscape (innovation while conserving the existing phenotypes (conservation suffices to cause the evolution of all the networks in a population towards criticality. Furthermore, the networks produced by this evolutionary process exhibit structures with hubs (global regulators similar to the observed topology of real gene regulatory networks. Thus, dynamical criticality and certain elementary topological properties of gene regulatory networks can emerge as a byproduct of the evolvability of the phenotypic landscape.

Reconstructing the ecological impacts of eight decades of mining, metallurgical, and municipal activities on a small boreal lake in northern Canada.

Science.gov (United States)

Doig, Lorne E; Schiffer, Stephanie T; Liber, Karsten

2015-07-01

As a result of long-term metal mining and metallurgical activities, the sediment of Ross Lake (Flin Flon, MB, Canada) is highly contaminated with metals and other elements. Although the effluents likely were discharged into Ross Lake as early as the late 1920s, lake biophysical data were not collected until 1973, more than 4 decades after the onset of mining and municipal activities. The early influence of these activities on the ecology of Ross Lake is unknown, as are the effects of improvements to metallurgical effluent quality and discontinuation of municipal wastewater discharge into the lake's north basin. To address this knowledge gap, analyses typical of paleolimnological investigations were applied to cores of sediment collected in 2009 from the south basin of Ross Lake. Stratigraphic analyses of physicochemical sediment characteristics (e.g., the concentrations of metals and other elements, organic C, total N, and δ(13)C and δ(15)N values) and subfossil remains (diatoms, Chironomidae, Chaoborus, and Cladocera) were used to infer historical biological and chemical changes in Ross Lake. With the onset of mining activities, concentrations of various elements (e.g., As, Cr, Cu, Zn, and Se) increased dramatically in the sediment profile, eventually declining with improved tailings management. Nevertheless, concentrations of metals in recent sediments remain elevated compared with pre-industrial sediments. Constrained cluster analyses demonstrated distinct pre-industrial and postindustrial communities for both the diatoms and chironomids. The biodiversity of the postindustrial diatom assemblages were much reduced compared with the pre-industrial assemblages. The postindustrial chironomid assemblage was dominated by Chironomus and to a lesser extent by Procladius, suggesting that Ross Lake became a degraded environment. Abundances of Cladocera and Chaoborus were severely reduced in the postindustrial era, likely because of metals toxicity. Overall, improvements

A CFD study on the dust behaviour in a metallurgical waste-heat boiler

Energy Technology Data Exchange (ETDEWEB)

Yongxiang, Yang; Jokilaakso, A [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Materials Processing and Powder Metallurgy

1998-12-31

A waste-heat boiler forms an essential part for the treatment of high temperature flue-gases in most metallurgical processes. Flue-dust carried by the furnace off-gas has to be captured efficiently in the waste-heat boilers before entering the downstream gas purification equipment. Flue dust may accumulate and foul on the heat transfer surfaces such as tube-walls, narrow conjunctions between the boiler and the furnace uptake, and thus may cause smelter shutdown, and interrupt the production. A commercial CFD package is used as the major tool on modelling the dust flow and settling in the waste-heat boiler of an industrial copper flash smelter. In the presentation, dust settling behaviour is illustrated for a wide range of particle sizes, and dust capture efficiency in the radiation section of the boiler for different particle sizes has been shown with the transient simulation. The simulation aims at providing detailed information of dust behaviour in the waste-heat boiler in sulphide smelting. (author) 11 refs.

Termination of the Special Metallurgical (SM) Building at Mound Laboratory: a final report

International Nuclear Information System (INIS)

Harris, W.R.; Kokenge, B.R.; Marsh, G.C.

1976-01-01

The report describes and highlights the more important factors associated with the termination of the Special Metallurgical (SM) Building at Mound Laboratory. As a result, a written record of the more important techniques and procedures is now available for reference by others involved in similar termination efforts. Included in this report is a description of the organizational units that were used in this effort along with a description of their responsibilities. A general description of the SM Building and a discussion of the more relevant procedures and equipment that were used are also presented. In addition, pertinent Health Physics information, such as personnel exposure, final wipe levels in the terminated facility, and assays of the structure, are provided. Based on the experience gained from this project, recommendations were made regarding the design of future radioactive material handling facilities so that when they are ultimately terminated the effort can be accomplished more efficiently

A CFD study on the dust behaviour in a metallurgical waste-heat boiler

Energy Technology Data Exchange (ETDEWEB)

Yang Yongxiang; Jokilaakso, A. [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Materials Processing and Powder Metallurgy

1997-12-31

A waste-heat boiler forms an essential part for the treatment of high temperature flue-gases in most metallurgical processes. Flue-dust carried by the furnace off-gas has to be captured efficiently in the waste-heat boilers before entering the downstream gas purification equipment. Flue dust may accumulate and foul on the heat transfer surfaces such as tube-walls, narrow conjunctions between the boiler and the furnace uptake, and thus may cause smelter shutdown, and interrupt the production. A commercial CFD package is used as the major tool on modelling the dust flow and settling in the waste-heat boiler of an industrial copper flash smelter. In the presentation, dust settling behaviour is illustrated for a wide range of particle sizes, and dust capture efficiency in the radiation section of the boiler for different particle sizes has been shown with the transient simulation. The simulation aims at providing detailed information of dust behaviour in the waste-heat boiler in sulphide smelting. (author) 11 refs.

Social memory, social stress, and economic behaviors

OpenAIRE

Taiki Takahashi

2005-01-01

Social memory plays a pivotal role in social behaviors, from mating behaviors to cooperative behaviors based on reciprocal altruism. More specifically, social/person recognition memory is supposed, by behavioral-economic and game-theoretic analysis, to be required for tit- for-tat like cooperative behaviors to evolve under the N-person iterated prisoner fs dilemma game condition. Meanwhile, humans are known to show a social stress response during face-to-face social interactions, which might ...

Evolvable Neural Software System

Science.gov (United States)

Curtis, Steven A.

2009-01-01

The Evolvable Neural Software System (ENSS) is composed of sets of Neural Basis Functions (NBFs), which can be totally autonomously created and removed according to the changing needs and requirements of the software system. The resulting structure is both hierarchical and self-similar in that a given set of NBFs may have a ruler NBF, which in turn communicates with other sets of NBFs. These sets of NBFs may function as nodes to a ruler node, which are also NBF constructs. In this manner, the synthetic neural system can exhibit the complexity, three-dimensional connectivity, and adaptability of biological neural systems. An added advantage of ENSS over a natural neural system is its ability to modify its core genetic code in response to environmental changes as reflected in needs and requirements. The neural system is fully adaptive and evolvable and is trainable before release. It continues to rewire itself while on the job. The NBF is a unique, bilevel intelligence neural system composed of a higher-level heuristic neural system (HNS) and a lower-level, autonomic neural system (ANS). Taken together, the HNS and the ANS give each NBF the complete capabilities of a biological neural system to match sensory inputs to actions. Another feature of the NBF is the Evolvable Neural Interface (ENI), which links the HNS and ANS. The ENI solves the interface problem between these two systems by actively adapting and evolving from a primitive initial state (a Neural Thread) to a complicated, operational ENI and successfully adapting to a training sequence of sensory input. This simulates the adaptation of a biological neural system in a developmental phase. Within the greater multi-NBF and multi-node ENSS, self-similar ENI s provide the basis for inter-NBF and inter-node connectivity.

Go reconfigure: how fish change shape as they swim and evolve.

Science.gov (United States)

Long, John H; Porter, Marianne E; Root, Robert G; Liew, Chun Wai

2010-12-01

The bodies of fish change shape over propulsive, behavioral, developmental, and evolutionary time scales, a general phenomenon that we call "reconfiguration". Undulatory, postural, and form-reconfiguration can be distinguished, studied independently, and examined in terms of mechanical interactions and evolutionary importance. Using a combination of live, swimming fishes and digital robotic fish that are autonomous and self-propelled, we examined the functional relation between undulatory and postural reconfiguration in forward swimming, backward swimming, and yaw turning. To probe how postural and form reconfiguration interact, the yaw turning of leopard sharks was examined using morphometric and kinematic analyses. To test how undulatory reconfiguration might evolve, the digital robotic fish were subjected to selection for enhanced performance in a simulated ecology in which each individual had to detect and move towards a food source. In addition to the general issue of reconfiguration, these investigations are united by the fact that the dynamics of undulatory and postural reconfigurations are predicted to be determined, in part, by the structural stiffness of the fish's body. Our method defines undulatory reconfiguration as the combined, point-by-point periodic motion of the body, leaving postural reconfiguration as the combined deviations from undulatory reconfiguration. While undulatory reconfiguration appears to be the sole or primary propulsive driver, postural reconfiguration may contribute to propulsion in hagfish and it is correlated with differences in forward, and backward, swimming in lamprey. Form reconfigures over developmental time in leopard sharks in a manner that is consistent with an allometric scaling theory in which structural stiffness of the body is held constant. However, correlation of a form proxy for structural stiffness of the body suggests that body stiffness may scale in order to limit maximum postural reconfiguration during routine

Evolving self-assembly in autonomous homogeneous robots: experiments with two physical robots.

Science.gov (United States)

Ampatzis, Christos; Tuci, Elio; Trianni, Vito; Christensen, Anders Lyhne; Dorigo, Marco

2009-01-01

This research work illustrates an approach to the design of controllers for self-assembling robots in which the self-assembly is initiated and regulated by perceptual cues that are brought forth by the physical robots through their dynamical interactions. More specifically, we present a homogeneous control system that can achieve assembly between two modules (two fully autonomous robots) of a mobile self-reconfigurable system without a priori introduced behavioral or morphological heterogeneities. The controllers are dynamic neural networks evolved in simulation that directly control all the actuators of the two robots. The neurocontrollers cause the dynamic specialization of the robots by allocating roles between them based solely on their interaction. We show that the best evolved controller proves to be successful when tested on a real hardware platform, the swarm-bot. The performance achieved is similar to the one achieved by existing modular or behavior-based approaches, also due to the effect of an emergent recovery mechanism that was neither explicitly rewarded by the fitness function, nor observed during the evolutionary simulation. Our results suggest that direct access to the orientations or intentions of the other agents is not a necessary condition for robot coordination: Our robots coordinate without direct or explicit communication, contrary to what is assumed by most research works in collective robotics. This work also contributes to strengthening the evidence that evolutionary robotics is a design methodology that can tackle real-world tasks demanding fine sensory-motor coordination.

Evolving phenotypic networks in silico.

Science.gov (United States)

François, Paul

2014-11-01

Evolved gene networks are constrained by natural selection. Their structures and functions are consequently far from being random, as exemplified by the multiple instances of parallel/convergent evolution. One can thus ask if features of actual gene networks can be recovered from evolutionary first principles. I review a method for in silico evolution of small models of gene networks aiming at performing predefined biological functions. I summarize the current implementation of the algorithm, insisting on the construction of a proper "fitness" function. I illustrate the approach on three examples: biochemical adaptation, ligand discrimination and vertebrate segmentation (somitogenesis). While the structure of the evolved networks is variable, dynamics of our evolved networks are usually constrained and present many similar features to actual gene networks, including properties that were not explicitly selected for. In silico evolution can thus be used to predict biological behaviours without a detailed knowledge of the mapping between genotype and phenotype. Copyright © 2014 The Author. Published by Elsevier Ltd.. All rights reserved.

canEvolve: a web portal for integrative oncogenomics.

Directory of Open Access Journals (Sweden)

Mehmet Kemal Samur

Full Text Available BACKGROUND & OBJECTIVE: Genome-wide profiles of tumors obtained using functional genomics platforms are being deposited to the public repositories at an astronomical scale, as a result of focused efforts by individual laboratories and large projects such as the Cancer Genome Atlas (TCGA and the International Cancer Genome Consortium. Consequently, there is an urgent need for reliable tools that integrate and interpret these data in light of current knowledge and disseminate results to biomedical researchers in a user-friendly manner. We have built the canEvolve web portal to meet this need. RESULTS: canEvolve query functionalities are designed to fulfill most frequent analysis needs of cancer researchers with a view to generate novel hypotheses. canEvolve stores gene, microRNA (miRNA and protein expression profiles, copy number alterations for multiple cancer types, and protein-protein interaction information. canEvolve allows querying of results of primary analysis, integrative analysis and network analysis of oncogenomics data. The querying for primary analysis includes differential gene and miRNA expression as well as changes in gene copy number measured with SNP microarrays. canEvolve provides results of integrative analysis of gene expression profiles with copy number alterations and with miRNA profiles as well as generalized integrative analysis using gene set enrichment analysis. The network analysis capability includes storage and visualization of gene co-expression, inferred gene regulatory networks and protein-protein interaction information. Finally, canEvolve provides correlations between gene expression and clinical outcomes in terms of univariate survival analysis. CONCLUSION: At present canEvolve provides different types of information extracted from 90 cancer genomics studies comprising of more than 10,000 patients. The presence of multiple data types, novel integrative analysis for identifying regulators of oncogenesis, network

Environmental Conflicts in Mining, Quarrying and Metallurgical Industries in the Iberian Peninsula (19th and 20th Century): Pollution and Popular Protest

OpenAIRE

Guimarães, Paulo Eduardo

2014-01-01

ENVIRONMENTAL CONFLICTS IN MINING, QUARRYING, AND METALLURGICAL INDUSTRIES IN THE IBERIAN PENINSULA (19TH AND 20TH CENTURY): POLLUTION AND PUBLIC PROTEST. Paulo E. Guimarães, NICPRI / University of Évora (Portugal) J. D. Pérez Cebada, Universidad of Huelva (Spain) Comparative and transnational analyses of social conflicts, related to the environmental changes produced by modern and contemporary mining industries, have been a topic of growing academic interest for the last two decad...

Assessment of the effect of Nd:YAG laser pulse operating parameters on the metallurgical characteristics of different tool steels using DOE software

OpenAIRE

Muhič, T.; Kosec, L.; Liedl, G.; Pleterski, M.

2011-01-01

To ensure the reliability of repair welded tool surfaces, clad quality should be improved. The relationships between metallurgical characteristics of cladding and laser input welding parameters were studied using the design of experiments software. The influence of laser power, welding speed, focal point position and diameter of welding wire on the weld-bead geometry (i.e. penetration, cladding zone width and heat-affected-zone width), microstructural homogeneity, dilution and bond strength w...

Thermo-mecano-metallurgical modelling of welding: application to welded joints in nuclear power plants

International Nuclear Information System (INIS)

Cosimo, Alejandro

2014-01-01

The Thermo-Mecano-Metallurgical (TMM) modelling of welding is considered in this thesis, where the high non-linearity and the multiphysics character of the problem makes necessary to study different areas of Computational Mechanics. Each of the main problems, specifically the thermal, the mechanical and the metallurgical problems, are separately investigated. In the context of Computational Welding Mechanics (CWM), their coupling is solved by means of a staggered approach making the hypothesis that they are weakly-coupled. In the case of the thermal problem, the primary complication is stated by the solid/liquid phase change. Classical formulations dealing with the solution of this problem suffer from instabilities associated to the discontinuity of the temperature gradient at the phase change boundary. This issue is studied in this work by considering an enriched finite element formulation with the ability of representing the gradient discontinuity inside finite elements. It is remarked that the proposed method avoids the use of an auxiliary equation to determine the enrichment position, which is common for level set formulations. The mechanical behaviour of bodies during solidification is revisited and implemented as part of the Finite Element (FE) framework OOFELIE. When possible, microstructure evolution must be considered in order to correctly predict Weld Residual Stresses (WRS). In this context, the implementation of a particular model for predicting microstructure evolution comes in association with the restriction that it can be applied to a reduced number of materials. In order to deal with this issue, the conception of a computational tool flexible enough to describe a wide range of materials is undertaken. Additionally, a model describing the Titanium alloy Ti6Al4V is particularly considered. The high computational cost of welding problems is addressed by means of the formulation of Hyper-Reduced Order Models (HROMs), and the parallelization of the FE

Interfacial characterization of SLM parts in multi-material processing: Metallurgical diffusion between 316L stainless steel and C18400 copper alloy

Energy Technology Data Exchange (ETDEWEB)

Liu, Z.H., E-mail: AZHLIU@ntu.edu.sg; Zhang, D.Q., E-mail: ZHANGDQ@ntu.edu.sg; Sing, S.L., E-mail: SING0011@e.ntu.edu.sg; Chua, C.K., E-mail: MCKCHUA@ntu.edu.sg; Loh, L.E., E-mail: LELOH1@e.ntu.edu.sg

2014-08-15

Multi-material processing in selective laser melting using a novel approach, by the separation of two different materials within a single dispensing coating system was investigated. 316L stainless steel and UNS C18400 Cu alloy multi-material samples were produced using selective laser melting and their interfacial characteristics were analyzed using focused ion beam, scanning electron microscopy, energy dispersive spectroscopy and electron back scattered diffraction techniques. A substantial amount of Fe and Cu element diffusion was observed at the bond interface suggesting good metallurgical bonding. Quantitative evidence of good bonding at the interface was also obtained from the tensile tests where the fracture was initiated at the copper region. Nevertheless, the tensile strength of steel/Cu SLM parts was evaluated to be 310 ± 18 MPa and the variation in microhardness values was found to be gradual along the bonding interface from the steel region (256 ± 7 HV{sub 0.1}) to the copper region (72 ± 3 HV{sub 0.1}). - Highlights: • Multi-material processing was successfully implemented and demonstrated in SLM. • Bi-metallic laminates of steel/Cu were successfully produced with the SLM process. • A substantial amount of Fe and Cu diffusion was observed at the bond interface. • Good metallurgical bonding was obtained at the interface of the steel/Cu laminates. • Highly refined microstructure was obtained due to rapid solidification in SLM.

On the Evolution of Behaviors through Embodied Imitation.

Science.gov (United States)

Erbas, Mehmet D; Bull, Larry; Winfield, Alan F T

2015-01-01

This article describes research in which embodied imitation and behavioral adaptation are investigated in collective robotics. We model social learning in artificial agents with real robots. The robots are able to observe and learn each others' movement patterns using their on-board sensors only, so that imitation is embodied. We show that the variations that arise from embodiment allow certain behaviors that are better adapted to the process of imitation to emerge and evolve during multiple cycles of imitation. As these behaviors are more robust to uncertainties in the real robots' sensors and actuators, they can be learned by other members of the collective with higher fidelity. Three different types of learned-behavior memory have been experimentally tested to investigate the effect of memory capacity on the evolution of movement patterns, and results show that as the movement patterns evolve through multiple cycles of imitation, selection, and variation, the robots are able to, in a sense, agree on the structure of the behaviors that are imitated.

Salmonid behavior and water temperature

Science.gov (United States)

Sally T. Sauter; John McMillan; Jason B. Dunham

2001-01-01

Animals react not only to immediate changes in their environment but also to cues that signal long-term changes to which they must adapt to survive. A proximate factor stimulates an animal’s immediate behavioral response, whereas what is known as an ultimate factor causes an animal to adjust its behavior to evolving conditions, thereby increasing its fitness and...

Powder metallurgical low-modulus Ti-Mg alloys for biomedical applications.

Science.gov (United States)

Liu, Yong; Li, Kaiyang; Luo, Tao; Song, Min; Wu, Hong; Xiao, Jian; Tan, Yanni; Cheng, Ming; Chen, Bing; Niu, Xinrui; Hu, Rong; Li, Xiaohui; Tang, Huiping

2015-11-01

In this work, powder metallurgical (PM) Ti-Mg alloys were prepared using combined techniques of mechanical alloying and spark plasma sintering. The alloys mainly consist of super saturations of Mg in Ti matrix, and some laminar structured Ti- and Mg-rich phases. The PM Ti-Mg alloys contain a homogeneous mixtures of nanocrystalline Mg and Ti phases. The novel microstructures result in unconventional mechanical and biological properties. It has been shown that the PM Ti-Mg alloys have a much lower compression modulus (36-50GPa) compared to other Ti alloys, but still remain a very high compressive strength (1500-1800MPa). In addition, the PM Ti-Mg alloys show good biocompatibility and bioactivity. Mg can dissolve in the simulated body fluids, and induce the formation of the calcium phosphate layer. The compression modulus of PM Ti-Mg alloys decreases with the amount of Mg, while the bioactivity increases. Although the corrosion resistance of Ti-Mg alloys decreases with the content of Mg, the alloys still show good stability in simulated body fluid under electrochemical conditions. The indirect and direct cytotoxicity results show that PM Ti-Mg alloys have a good biocompatibility to NIH-3T3 cells. Therefore, the PM Ti-Mg alloys are promising candidates in biomedical applications. Copyright © 2015 Elsevier B.V. All rights reserved.

Mechanical and Metallurgical Properties of Various Nickel-Titanium Rotary Instruments

Directory of Open Access Journals (Sweden)

Kyu-Sang Shim

2017-01-01

Full Text Available The aim of this study was to investigate the effect of thermomechanical treatment on mechanical and metallurgical properties of nickel-titanium (NiTi rotary instruments. Eight kinds of NiTi rotary instruments with sizes of ISO #25 were selected: ProFile, K3, and One Shape for the conventional alloy; ProTaper NEXT, Reciproc, and WaveOne for the M-wire alloy; HyFlex CM for the controlled memory- (CM- wire; and TF for the R-phase alloy. Torsional fracture and cyclic fatigue fracture tests were performed. Products underwent a differential scanning calorimetry (DSC analysis. The CM-wire and R-phase groups had the lowest elastic modulus, followed by the M-wire group. The maximum torque of the M-wire instrument was comparable to that of a conventional instrument, while those of the CM-wire and R-phase instruments were lower. The angular displacement at failure (ADF for the CM-wire and R-phase instruments was higher than that of conventional instruments, and ADF of the M-wire instruments was lower. The cyclic fatigue resistance of the thermomechanically treated NiTi instruments was higher. DSC plots revealed that NiTi instruments made with the conventional alloy were primarily composed of austenite at room temperature; stable martensite and R-phase were found in thermomechanically treated instruments.

A mapping closure for turbulent scalar mixing using a time-evolving reference field

Science.gov (United States)

Girimaji, Sharath S.

1992-01-01

A general mapping-closure approach for modeling scalar mixing in homogeneous turbulence is developed. This approach is different from the previous methods in that the reference field also evolves according to the same equations as the physical scalar field. The use of a time-evolving Gaussian reference field results in a model that is similar to the mapping closure model of Pope (1991), which is based on the methodology of Chen et al. (1989). Both models yield identical relationships between the scalar variance and higher-order moments, which are in good agreement with heat conduction simulation data and can be consistent with any type of epsilon(phi) evolution. The present methodology can be extended to any reference field whose behavior is known. The possibility of a beta-pdf reference field is explored. The shortcomings of the mapping closure methods are discussed, and the limit at which the mapping becomes invalid is identified.

Influence of metallurgical and electrochemical factors on cracking of steels at nuclear power plants under high temperature

International Nuclear Information System (INIS)

Pokhmurskii, V.I.; Gnyp, I.P.

1994-01-01

The influence of metallurgical heterogeneities in steels and electrochemical factors on corrosion cracking under high temperature water environment is studied, with special emphasis on the influence of manganese sulfide inclusions and other non-metallic ones on the crack growth rate. Results show that the electro-chemical conditions for an hydrogen concentration increase in a pre-failure zone exist at a crack tip under cyclic loading; hydrogen penetrating into metals at high temperature reduces manganese sulfides, ferric carbides, and cause high pressure of gases in micro-discontinuities, thus leading to cyclic corrosion cracking; anodic (relatively to a metal matrix) inclusions are rather the cause of steel cracking resistance decrease than cathodic ones. 16 refs., 4 figs

A metallurgical study of Nāga Bhasma

Directory of Open Access Journals (Sweden)

Dev Nath Singh Gautam

2017-01-01

Full Text Available Background: The metal Nāga (Lead is being used by Indians since ancient times. Its external and internal uses have been described in Caraka, Suśruta and other Ayurvedic Saṃhitā. According to most of the Rasa texts, Nāga Bhasma and its formulations are used in many diseases such as Prameha, Jvara, Gulma, Śukrameha etc. Objectives: In the present study, Nāga Bhasma was prepared by the traditional Puṭa method (TPM and by the electric muffle furnace Puṭa method (EMFPM and standardized using Metallographic studies. Doing so helps in the study of the microstructure of Nāga Bhasma and also helps in the identification of the metal particles along with the nature of compound formed during the Māraṇa (Bhasmīkaraṇa process. Setting and Design: Different samples from initial raw material to final product of Nāga Bhasma were collected during the pharmaceutical process (1st, 30th and 60th Puṭa from both methods i.e. TPM and EMFPM. Samples from both methods were studied using metallographic examination. Materials and Methods: The processing of the Nāga Bhasma (ṣaṣṭipuṭa was done according to Ānanda Kanda[9] Samples from the raw material i.e. Aśodhita Nāga (raw Lead and that processed after 1st, 30th and 60th Puṭa from both methods i.e. traditional Puṭa method (using heat from burning of cow dung cakes and electric muffle furnace Puṭa method were taken. They were mounted on self hardening acrylic base. After careful polishing to obtain scratch free surface of product, they were used for metallurgical study. Conclusion: This study shows that traditional Puṭa method may be better than electric muffle furnace Puṭa method because of more homogeneous distribution of Lead sulphide in the Nāga Bhasma which is prepared by traditional method.

An evolving systems-based methodology for healthcare planning.

Science.gov (United States)

Warwick, Jon; Bell, Gary

2007-01-01

Healthcare planning seems beset with problems at all hierarchical levels. These are caused by the 'soft' nature of many of the issues present in healthcare planning and the high levels of complexity inherent in healthcare services. There has, in recent years, been a move to utilize systems thinking ideas in an effort to gain a better understanding of the forces at work within the healthcare environment and these have had some success. This paper argues that systems-based methodologies can be further enhanced by metrication and modeling which assist in exploring the changed emergent behavior of a system resulting from management intervention. The paper describes the Holon Framework as an evolving systems-based approach that has been used to help clients understand complex systems (in the education domain) that would have application in the analysis of healthcare problems.

Thermal expansion behavior in fabricated cellular structures

International Nuclear Information System (INIS)

Oruganti, R.K.; Ghosh, A.K.; Mazumder, J.

2004-01-01

Thermal expansion behavior of cellular structures is of interest in applications where undesirable deformation and failure are caused by thermal expansion mismatch. This report describes the role of processing-induced effects and metallurgical aspects of melt-processed cellular structures, such as a bi-material structure designed to contract on heating, as well as uni-material structures of regular and stochastic topology. This bi-material structure utilized the principle of internal geometric constraints to alter the expansion behavior of the internal ligaments to create overall contraction of the structure. Homogenization design method was used to design the structure, and fabrication was by direct metal deposition by laser melting of powder in another part of a joint effort. The degree of porosity and grain size in the fabricated structure are characterized and related to the laser deposition parameters. The structure was found to contract upon heating over a short range of temperature subsequent to which normal expansion ensued. Also examined in this report are uni-material cellular structures, in which internal constraints arise from residual stress variations caused by the fabrication process, and thereby alter their expansion characteristics. A simple analysis of thermal strain of this material supports the observed thermal expansion behavior

1Q/2Q00 M-Area and Metallurgical Laboratory Hazardous Waste Management Facilities Groundwater Monitoring and Corrective-Action Report - First and Second Quarters 2000 - Volumes I, II, and II

Energy Technology Data Exchange (ETDEWEB)

Chase, J.

2000-10-24

This report describes the groundwater monitoring and corrective-action program at the M-Area Hazardous Waste Management Facility (HWMF) and the Metallurgical Laboratory (Met Lab) HWMF at the Savannah River site (SRS) during first and second quarters of 2000.

1Q/2Q00 M-Area and Metallurgical Laboratory Hazardous Waste Management Facilities Groundwater Monitoring and Corrective-Action Report - First and Second Quarters 2000 - Volumes I, II, and II

International Nuclear Information System (INIS)

Chase, J.

2000-01-01

This report describes the groundwater monitoring and corrective-action program at the M-Area Hazardous Waste Management Facility (HWMF) and the Metallurgical Laboratory (Met Lab) HWMF at the Savannah River site (SRS) during first and second quarters of 2000

On the Benefits of Divergent Search for Evolved Representations

DEFF Research Database (Denmark)

Lehman, Joel; Risi, Sebastian; Stanley, Kenneth O

2012-01-01

Evolved representations in evolutionary computation are often fragile, which can impede representation-dependent mechanisms such as self-adaptation. In contrast, evolved representations in nature are robust, evolvable, and creatively exploit available representational features. This paper provide...

Environmental management and educational needs of the small and medium-sized businesses of the metallurgical sector in the south region of Madrid

International Nuclear Information System (INIS)

Urena, A.; Rams, J.; Mendez, F. J.; Rodriguez, J.

2004-01-01

In this study, the environmental management and needs of the small and medium-sized businesses of the metallurgical industry in the south region of Madrid were analysed. Information was obtained through a telephone questionnaire distributed to more than 170 companies. Although most of the respondent employees do not consider environmental training one of their priorities, they expressed their interest in implementing Environmental Management Systems, waste minimization and higher knowledge of the specific legal aspects. (Author) 7 refs

Change of the layout of an office of a metallurgical company: simple projects, big solutions.

Science.gov (United States)

Duarte, Luiz Carlos da Silva; Eckhardt, Moacir; da Motta, Giordano Paulo

2012-01-01

The posture, a good organization and the proper layout of the environment and workplaces have a positive influence on the income of an employee. To develop the work it is used a methodology that addressed the study phases of the theory involving the subject, description of the current situation, preparation of conceptions, choice of design, implementation and reporting of results. Through the project of "Change of the layout of an office of a metallurgical company" there was an intervention in these reported aspects providing improvements in the office, regarding ergonomic, layout, workplace and lighting issues, bringing welfare to the official, with the intent to improve its performance within the company and facilitating its actions, as the company's customer service. The results provided improvements in layout, in the workplace and especially in comfort for the human resources that perform their activities.

DIFFERENCES OF COMMITMENT BETWEEN GENERATIONS X AND Y – A STUDY IN A METALLURGICAL INDUSTRY

Directory of Open Access Journals (Sweden)

Fábio Teodoro Tolfo Ribas

2015-06-01

Full Text Available The way each generation acts in society and in organizations is always a matter of study and appreciation (LOMBARDIA; STEIN & PIN, 2008. Thus, this study aimed to examine the organizational commitment in its affetctive, instrumental and normative dimensions in different generational groups (X and Y of Metallurgical Industry in the city of Caxias do Sul (RS. The research is descriptive and quantitative in nature. To reach its objective it uses a validated questionnaire, based on Ribas 2010, with 96 professional of the administrative sector. The results identify that the respondents have very similar approaches regarding affective, instrumental and normative commitment perceptions. Still, it was noticed that the highest means for both generations, were obtained in the construct of affective commitment. The clearest difference emerged in the focus of instrumental commitment, which determines the individual’s need to remain in business.

The genotype-phenotype map of an evolving digital organism

OpenAIRE

Fortuna, Miguel A.; Zaman, Luis; Ofria, Charles; Wagner, Andreas

2017-01-01

To understand how evolving systems bring forth novel and useful phenotypes, it is essential to understand the relationship between genotypic and phenotypic change. Artificial evolving systems can help us understand whether the genotype-phenotype maps of natural evolving systems are highly unusual, and it may help create evolvable artificial systems. Here we characterize the genotype-phenotype map of digital organisms in Avida, a platform for digital evolution. We consider digital organisms fr...

EVOLVE

CERN Document Server

Deutz, André; Schütze, Oliver; Legrand, Pierrick; Tantar, Emilia; Tantar, Alexandru-Adrian

2017-01-01

This book comprises nine selected works on numerical and computational methods for solving multiobjective optimization, game theory, and machine learning problems. It provides extended versions of selected papers from various fields of science such as computer science, mathematics and engineering that were presented at EVOLVE 2013 held in July 2013 at Leiden University in the Netherlands. The internationally peer-reviewed papers include original work on important topics in both theory and applications, such as the role of diversity in optimization, statistical approaches to combinatorial optimization, computational game theory, and cell mapping techniques for numerical landscape exploration. Applications focus on aspects including robustness, handling multiple objectives, and complex search spaces in engineering design and computational biology.

Revisiting Robustness and Evolvability: Evolution in Weighted Genotype Spaces

Science.gov (United States)

Partha, Raghavendran; Raman, Karthik

2014-01-01

Robustness and evolvability are highly intertwined properties of biological systems. The relationship between these properties determines how biological systems are able to withstand mutations and show variation in response to them. Computational studies have explored the relationship between these two properties using neutral networks of RNA sequences (genotype) and their secondary structures (phenotype) as a model system. However, these studies have assumed every mutation to a sequence to be equally likely; the differences in the likelihood of the occurrence of various mutations, and the consequence of probabilistic nature of the mutations in such a system have previously been ignored. Associating probabilities to mutations essentially results in the weighting of genotype space. We here perform a comparative analysis of weighted and unweighted neutral networks of RNA sequences, and subsequently explore the relationship between robustness and evolvability. We show that assuming an equal likelihood for all mutations (as in an unweighted network), underestimates robustness and overestimates evolvability of a system. In spite of discarding this assumption, we observe that a negative correlation between sequence (genotype) robustness and sequence evolvability persists, and also that structure (phenotype) robustness promotes structure evolvability, as observed in earlier studies using unweighted networks. We also study the effects of base composition bias on robustness and evolvability. Particularly, we explore the association between robustness and evolvability in a sequence space that is AU-rich – sequences with an AU content of 80% or higher, compared to a normal (unbiased) sequence space. We find that evolvability of both sequences and structures in an AU-rich space is lesser compared to the normal space, and robustness higher. We also observe that AU-rich populations evolving on neutral networks of phenotypes, can access less phenotypic variation compared to

Measures to detect and control radioactive contaminated metallurgical scrap at border checkpoints in Poland

International Nuclear Information System (INIS)

Smagala, G.

1999-01-01

The issue of radioactive contaminated metallurgical scrap has never received a high priority in Poland and in the international community. Since the dissolution of the former Soviet Union a higher attention has been given to the problem. Poland which is located between the West and East Europe has the obligation to develop and implement an effective prevention and detection system. The reasons to increase national control and detection system at the border checkpoints in Poland are to avoid the following risks: post Chernobyl contamination transports of commodities; transport of contaminated metal scrap; transfer of radioactive waste for their disposal or utilization; high risk of becoming a transit country of illicit trafficking of nuclear materials and radioactive sources. In order to avoid the above-mentioned risks, Poland initiated in 1990, a deployment of the portable radiation devices at the border checkpoints and, as of 1998, the number of installed instruments exceeded a hundred. This paper presents Poland's activities to detect contaminated scrap at its border checkpoints. (author)

Review of New Technology for Preparing Crystalline Silicon Solar Cell Materials by Metallurgical Method

Science.gov (United States)

Li, Man; Dai, Yongnian; Ma, Wenhui; Yang, Bin; Chu, Qingmei

2017-11-01

The goals of greatly reducing the photovoltaic power cost and making it less than that of thermal power to realize photovoltaic power grid parity without state subsidies are focused on in this paper. The research status, key technologies and development of the new technology for preparing crystalline silicon solar cell materials by metallurgical method at home and abroad are reviewed. The important effects of impurities and defects in crystalline silicon on its properties are analysed. The importance of new technology on reducing production costs and improving its quality to increase the cell conversion efficiency are emphasized. The previous research results show that the raw materials of crystalline silicon are extremely abundant. The product of crystalline silicon can meet the quality requirements of solar cell materials: Si ≥ 6 N, P 1 Ω cm, minority carrier life > 25 μs cell conversion efficiency of about 19.3%, the product costs energy consumption energy consumption, low carbon and sustainable development are prospected.

Metallurgical Laboratory Hazardous Waste Management Facility groundwater monitoring report. Third quarter, 1994

International Nuclear Information System (INIS)

1994-12-01

During third quarter 1994, samples from AMB groundwater monitoring wells at the Metallurgical Laboratory Hazardous Waste Management Facility (Met Lab HWMF) were analyzed for selected heavy metals, indicator parameters, radionuclides, volatile organic compounds, and other constituents. Eight parameters exceeded standards during the quarter. As in previous quarters, tetrachloroethylene and trichloroethylene exceeded final Primary Drinking Water Standards (PDWS). Bis(2-ethylhexyl) phthalate exceeded final PDWS in one well. Aluminum, iron, manganese, tin, and total organic halogens exceeded the Savannah River Site (SRS) Flag 2 criteria. Groundwater flow direction and rate in the M-Area Aquifer Zone were similar to previous quarters. Conditions affecting determination of groundwater flow directions and rates in the Upper Lost Lake Aquifer Zone, Lower Lost Lake Aquifer Zone, and the Middle Sand Aquifer Zone of the Crouch Branch Confining Unit were also similar to previous quarters. During second quarter 1994, SRS received South Carolina Department of Health and Environmental Control approval for constructing five point-of-compliance wells and two plume definition wells near the Met Lab HWMF. This project began in July 1994 and is complete; however, analytical data from these wells is not available yet

Metallurgical examination of, and resin transfer from, Three Mile Island prefilter liners

Energy Technology Data Exchange (ETDEWEB)

McConnell, Jr, J W; Spaletta, H W

1984-08-01

Metallurgical examinations were performed on two EPICOR-II prefilter liners at the Idaho National Engineering Laboratory (INEL) to determine conditions of the liners and identify the minimum expected lifetime of those and other liners stored at INEL. The research work was accomplished by EG and G Idaho, Inc. for the EPICOR-II Research and Disposition Program, which is funded by the US Department of Energy. The EPICOR-II prefilter liners were used to filter radionuclides from contaminated water during cleanup of Three Mile Island Unit 2 (TMI-2). The liners were constructed of carbon steel with a phenolic protective coating and contained organic and inorganic ion-exchange filtration media. Program plans call for interim storage of EPICOR-II prefilters at INEL for up to ten years, before final disposal in high integrity containers at the Hanford, Washington commercial disposal site. This report describes the (a) resin transfer process used to empty liners for examination, (b) removal of metallographic sections from those liners, (c) specimen preparation, and (d) findings from metallographic examination of those specimens. A minimum lifetime for the liners is determined and recommendations are given for storage of wastes from future TMI-2 activities.

Metallurgical examination of, and resin transfer from, Three Mile Island prefilter liners

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Spaletta, H.W.

1984-08-01

Metallurgical examinations were performed on two EPICOR-II prefilter liners at the Idaho National Engineering Laboratory (INEL) to determine conditions of the liners and identify the minimum expected lifetime of those and other liners stored at INEL. The research work was accomplished by EG and G Idaho, Inc. for the EPICOR-II Research and Disposition Program, which is funded by the US Department of Energy. The EPICOR-II prefilter liners were used to filter radionuclides from contaminated water during cleanup of Three Mile Island Unit 2 (TMI-2). The liners were constructed of carbon steel with a phenolic protective coating and contained organic and inorganic ion-exchange filtration media. Program plans call for interim storage of EPICOR-II prefilters at INEL for up to ten years, before final disposal in high integrity containers at the Hanford, Washington commercial disposal site. This report describes the (a) resin transfer process used to empty liners for examination, (b) removal of metallographic sections from those liners, (c) specimen preparation, and (d) findings from metallographic examination of those specimens. A minimum lifetime for the liners is determined and recommendations are given for storage of wastes from future TMI-2 activities

The use of by-products from metallurgical and mineral industries as filler in cement-based materials.

Science.gov (United States)

Moosberg, Helena; Lagerblad, Björn; Forssberg, Eric

2003-02-01

This investigation has been made in order to make it possible to increase the use of by-products in cement-based materials. Use of by-products requires a screening procedure that will reliably determine their impact on concrete. A test procedure was developed. The most important properties were considered to be strength development, shrinkage, expansion and workability. The methods used were calorimetry, flow table tests, F-shape measurements, measurements of compressive and flexural strength and shrinkage/expansion measurements. Scanning electron microscopy was used to verify some results. Twelve by-products were collected from Swedish metallurgical and mineral industries and classified according to the test procedure. The investigation showed that the test procedure clearly screened out the materials that can be used in the production of concrete from the unsuitable ones.

Effect of CH3COOH on Hydrometallurgical Purification of Metallurgical-Grade Silicon Using HCl-HF Leaching

Science.gov (United States)

Tian, Chunjin; Lu, Haifei; Wei, Kuixian; Ma, Wenhui; Xie, Keqiang; Wu, Jijun; Lei, Yun; Yang, Bin; Morita, Kazuki

2018-04-01

The present study investigated the effects of adding CH3COOH to HCl and HF used to purify metallurgical-grade Si (MG-Si). After 6 h of leaching MG-Si with an acid mixture consisting of 4 mol L-1 HCl, 3 mol L-1 HF, and 3 mol L-1 CH3COOH at 348 K, the total impurity removal efficiency was 88.5%, exceeding the 81.5% removal efficiency obtained without addition of CH3COOH. The microstructural evolution of Si after etching with the two lixiviants indicated better dissolution of metal impurities in MG-Si when using the HCl-HF-CH3COOH mixture. Furthermore, the leaching kinetics of Fe using the HCl-HF and HCl-HF-CH3COOH mixtures were observed to depend on the interfacial chemical reactions.

Evolving Expert Knowledge Bases: Applications of Crowdsourcing and Serious Gaming to Advance Knowledge Development for Intelligent Tutoring Systems

Science.gov (United States)

Floryan, Mark

2013-01-01

This dissertation presents a novel effort to develop ITS technologies that adapt by observing student behavior. In particular, we define an evolving expert knowledge base (EEKB) that structures a domain's information as a set of nodes and the relationships that exist between those nodes. The structure of this model is not the particularly novel…

Distribution of impurity elements in slag-silicon equilibria for oxidative refining of metallurgical silicon for solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Johnston, M.D.; Barati, M. [Department of Materials Science and Engineering, The University of Toronto, 184 College Street, Toronto, Ont. (Canada)

2010-12-15

The possibility of refining metallurgical grade silicon to a high-purity product for solar cell applications by the slagging of impurity elements was investigated. Distribution coefficients were determined for B, Ca, Mg, Fe, K and P between magnesia or alumina saturated Al{sub 2}O{sub 3}-CaO-MgO-SiO{sub 2} and Al{sub 2}O{sub 3}-BaO-SiO{sub 2} slags and silicon at 1500 C. The partitioning of the impurity elements between molten silicon and slag was examined in terms of basicity and oxygen potential of the slag, with particular focus on the behaviour of boron and phosphorus. The experimental results showed that both of these aspects of slag chemistry have a significant influence on the distribution coefficient of B and P. Increasing the oxygen potential by additions of silica was found to increase the distribution coefficients for both B and P. Increasing the basicity of the slag was not always effective in achieving high removal of these elements from silicon as excess amounts of basic oxides lower the activity of silica and consequently the oxygen potential. The extent of this effect is such that increasing basicity can lead to a decrease in distribution coefficient. Increasing lime in the slag increased distribution coefficients for B and P, but this counterbalancing effect was such that distributions were the lowest in barium-containing slags, despite barium oxide being the most basic of the fluxes used in this study. The highest removal efficiencies achieved were of the order of 80% and 90% for B and P, respectively. It was demonstrated that for the removal of B and P from metallurgical-grade silicon to solar-grade levels, a slag mass about 5 times the mass of silicon would be required. (author)

Maintaining evolvability.

Science.gov (United States)

Crow, James F

2008-12-01

Although molecular methods, such as QTL mapping, have revealed a number of loci with large effects, it is still likely that the bulk of quantitative variability is due to multiple factors, each with small effect. Typically, these have a large additive component. Conventional wisdom argues that selection, natural or artificial, uses up additive variance and thus depletes its supply. Over time, the variance should be reduced, and at equilibrium be near zero. This is especially expected for fitness and traits highly correlated with it. Yet, populations typically have a great deal of additive variance, and do not seem to run out of genetic variability even after many generations of directional selection. Long-term selection experiments show that populations continue to retain seemingly undiminished additive variance despite large changes in the mean value. I propose that there are several reasons for this. (i) The environment is continually changing so that what was formerly most fit no longer is. (ii) There is an input of genetic variance from mutation, and sometimes from migration. (iii) As intermediate-frequency alleles increase in frequency towards one, producing less variance (as p --> 1, p(1 - p) --> 0), others that were originally near zero become more common and increase the variance. Thus, a roughly constant variance is maintained. (iv) There is always selection for fitness and for characters closely related to it. To the extent that the trait is heritable, later generations inherit a disproportionate number of genes acting additively on the trait, thus increasing genetic variance. For these reasons a selected population retains its ability to evolve. Of course, genes with large effect are also important. Conspicuous examples are the small number of loci that changed teosinte to maize, and major phylogenetic changes in the animal kingdom. The relative importance of these along with duplications, chromosome rearrangements, horizontal transmission and polyploidy

USING THE OUTSOURCING MECHANISM TO INCREASE THE EFFICIENCY OF REPAIR AND MAINTENANCE IN METALLURGICAL ENTERPRISES

Directory of Open Access Journals (Sweden)

Elena I. Kozlova

2017-01-01

Full Text Available Abstract. Objectives The aim of the work is to study the outsourcing mechanism from the point of view of increasing the efficiency of repair and maintenance at a metallurgical enterprise. Method Analysis of the experience of using outsourcing of repair services at domestic and foreign metallurgical enterprises was carried out. Analysis of the experience of the withdrawal from enterprise repair services into a separate outsourcing company has shown that the main advantages of this method of organising repair activities are an increase in the transparency of the costs of repairs and maintenance, and hence their reduction, as well as a reduction in the amount of equipment downtime. The main characteristics of outsourcing were revealed, substantiating its expediency. The restructuring of the repair system provides a step-by-step transition from decentralised to centralised structures of technical, mechanical, power and electrical repair services of enterprises, from the principle of "self-service" to the principle of "proprietary service" by isolating the subdivisions of the repair system from the structure of enterprises and creating competing members of the repair services market. Put another way, this is typified by moving away from the status of auxiliary production to a selfdependent activity. The stages of outsourcing the repair services of the enterprise are considered and possible problems that may arise in the course of the work of a working group are established to determine the suitability of outsourcing and to resolve the numerous issues arising from the transfer of repair functions. Results The findings of the research include approaches developed for overcoming risky situations: providing guarantees from the customer and the contractor and indicating them in the contract, increasing the motivation of the outsourcing company through a key performance indicator that should increase the interest of the performer in providing quality

The genotype-phenotype map of an evolving digital organism.

Directory of Open Access Journals (Sweden)

Miguel A Fortuna

2017-02-01

Full Text Available To understand how evolving systems bring forth novel and useful phenotypes, it is essential to understand the relationship between genotypic and phenotypic change. Artificial evolving systems can help us understand whether the genotype-phenotype maps of natural evolving systems are highly unusual, and it may help create evolvable artificial systems. Here we characterize the genotype-phenotype map of digital organisms in Avida, a platform for digital evolution. We consider digital organisms from a vast space of 10141 genotypes (instruction sequences, which can form 512 different phenotypes. These phenotypes are distinguished by different Boolean logic functions they can compute, as well as by the complexity of these functions. We observe several properties with parallels in natural systems, such as connected genotype networks and asymmetric phenotypic transitions. The likely common cause is robustness to genotypic change. We describe an intriguing tension between phenotypic complexity and evolvability that may have implications for biological evolution. On the one hand, genotypic change is more likely to yield novel phenotypes in more complex organisms. On the other hand, the total number of novel phenotypes reachable through genotypic change is highest for organisms with simple phenotypes. Artificial evolving systems can help us study aspects of biological evolvability that are not accessible in vastly more complex natural systems. They can also help identify properties, such as robustness, that are required for both human-designed artificial systems and synthetic biological systems to be evolvable.

The genotype-phenotype map of an evolving digital organism.

Science.gov (United States)

Fortuna, Miguel A; Zaman, Luis; Ofria, Charles; Wagner, Andreas

2017-02-01

To understand how evolving systems bring forth novel and useful phenotypes, it is essential to understand the relationship between genotypic and phenotypic change. Artificial evolving systems can help us understand whether the genotype-phenotype maps of natural evolving systems are highly unusual, and it may help create evolvable artificial systems. Here we characterize the genotype-phenotype map of digital organisms in Avida, a platform for digital evolution. We consider digital organisms from a vast space of 10141 genotypes (instruction sequences), which can form 512 different phenotypes. These phenotypes are distinguished by different Boolean logic functions they can compute, as well as by the complexity of these functions. We observe several properties with parallels in natural systems, such as connected genotype networks and asymmetric phenotypic transitions. The likely common cause is robustness to genotypic change. We describe an intriguing tension between phenotypic complexity and evolvability that may have implications for biological evolution. On the one hand, genotypic change is more likely to yield novel phenotypes in more complex organisms. On the other hand, the total number of novel phenotypes reachable through genotypic change is highest for organisms with simple phenotypes. Artificial evolving systems can help us study aspects of biological evolvability that are not accessible in vastly more complex natural systems. They can also help identify properties, such as robustness, that are required for both human-designed artificial systems and synthetic biological systems to be evolvable.

Reprocessing of metallurgical slag into materials for the building industry

International Nuclear Information System (INIS)

Pioro, L.S.; Pioro, I.L.

2004-01-01

Several methods of reprocessing metallurgical (blast furnace) slag into materials for the building industry, based on melting aggregates with submerged combustion, were developed and tested. The first method involves melting hot slag with some additives directly in a slag ladle with a submerged gas-air burner, with the objective of producing stabilized slag or glass-ceramic. The second method involves direct draining of melted slag from a ladle into the slag receiver, with subsequent control of the slag draining into the converter where special charging materials are added to the melt, with the objective of producing glass-ceramic. A third method involves melting cold slag with some additives inside a melting converter with submerged gas-air burners, with the objective of producing glass-ceramic fillers for use in road construction. Specific to the melting process is the use of a gas-air mixture with direct combustion inside the melt. This feature provides melt bubbling to help achieve maximum heat transfer from combustion products to the melt, improve mixing (and therefore homogeneity of the melt), and increases the rate of chemical reactions. The experimental data for different aspects of the proposed methods are presented. The reprocessed blast-furnace slag in the form of granules can be used as fillers for concretes, asphalts, and as additives in the production of cement, bricks and other building materials. As well, reprocessed blast-furnace slag can be poured into forms for the production of glass-ceramic tiles

Evolvability as a Quality Attribute of Software Architectures

NARCIS (Netherlands)

Ciraci, S.; van den Broek, P.M.; Duchien, Laurence; D'Hondt, Maja; Mens, Tom

We review the definition of evolvability as it appears on the literature. In particular, the concept of software evolvability is compared with other system quality attributes, such as adaptability, maintainability and modifiability.

Metallurgical evaluation of failed post-tensioned containment tendon anchors at Joseph M. Farley Unit 2

International Nuclear Information System (INIS)

Czajkowski, C.J.

1986-01-01

A metallurgical examination has been performed on three failed post-tensioned containment tendon anchors and one intact anchor from the Farley Unit 2 Nuclear Power Station. The evaluation consisted of chemical/mechanical testing, optical microscopy, scanning electron microscopy, and energy dispersive spectroscopy. The conclusions drawn from the investigation were: 1) the anchors met the chemical and mechanical properties of AISI 4140/4142 steel; 2) there was no evidence of phosphorous segregation to the grain boundary (by ethereal picral etch); 3) the observed cracking was generally a mixed mode of intergranular and quasi-cleavage as well as ductile rupture with the intergranular cracking occurring along prior austenite grain boundaries; 4) the results of the mechanical tests coupled with the discontinuous nature of the intergranular areas and the elimination of other modes of failure give sufficient indication that the failure was a hydrogen induced cracking phenomenon

Green Consumption Behavior Antecedents

DEFF Research Database (Denmark)

Pagiaslis, Anastasios; Krystallis Krontalis, Athanasios

2014-01-01

The present study adds to the evolving literature on green consumer behavior by examining through statistically robust methods the effect and interrelationships of the key constructs of environmental concern, consumer environmental knowledge, beliefs about biofuels, and behavioral intention (i...... for the environment has a positive and direct impact on environmental knowledge, beliefs, and behavioral intention. Also, demographics determine levels of concern for the environment and environmental knowledge. All constructs associate positively with one another delineating that the interdependencies between them...... are important when accounting for environmental behavior. Future research should validate present results with the use of cross-cultural samples and investigate whether environmental concern increases due to social desirability response bias....

Quest for steel quality: the role of metallurgical chemistry

Energy Technology Data Exchange (ETDEWEB)

McLean, A. [Toronto Univ., ON (Canada). Dept. of Metallurgy and Materials Science

2000-10-01

Improvements in the quality of steels and the role played by metallurgical chemistry to bring about those improvements are discussed. The particular emphasis is on the chemical behaviour of solutes in molten steel and the reaction between steel, slag and refractory materials and the manner in which they influence the physical properties and performance of the steel product. As an illustration of the contribution of chemistry to steel making the case of the steel plates used in the construction of the Titanic is cited. In 1911 when the Titanic was constructed by Harland and Wolff at their Belfast shipyard, the steel plates used in the hull met all then current specifications. In 1992 when a number of steel samples recovered from the Titanic were examined, it was found that the hull of the vessel was constructed of low carbon, semi-killed steel, produced in the open-hearth process. Microstructural analysis showed extensive carbon banding, typical of hot rolled 0.2 per cent carbon steel. Also found were long manganese sulphide inclusions elongated in the rolling direction, some of which exceeded 25 mm in length. It was determined that as a consequence of these inclusions, at a seawater temperature of 0 degree C, the hull plates of the Titanic had essentially no resistance to fracture. Today's high quality steels used in applications such as Arctic pipelines, offshore platforms, icebreakers and ships for the transportation of natural gas, oxygen and sulphur concentrations are frequently less than 10 ppm. These elements have a profound influence of the quality of the final steel products by virtue of their effect of hindering the formation of inclusions. 2 refs., 3 figs.

EVOLVE 2014 International Conference

CERN Document Server

Tantar, Emilia; Sun, Jian-Qiao; Zhang, Wei; Ding, Qian; Schütze, Oliver; Emmerich, Michael; Legrand, Pierrick; Moral, Pierre; Coello, Carlos

2014-01-01

This volume encloses research articles that were presented at the EVOLVE 2014 International Conference in Beijing, China, July 1–4, 2014.The book gathers contributions that emerged from the conference tracks, ranging from probability to set oriented numerics and evolutionary computation; all complemented by the bridging purpose of the conference, e.g. Complex Networks and Landscape Analysis, or by the more application oriented perspective. The novelty of the volume, when considering the EVOLVE series, comes from targeting also the practitioner’s view. This is supported by the Machine Learning Applied to Networks and Practical Aspects of Evolutionary Algorithms tracks, providing surveys on new application areas, as in the networking area and useful insights in the development of evolutionary techniques, from a practitioner’s perspective. Complementary to these directions, the conference tracks supporting the volume, follow on the individual advancements of the subareas constituting the scope of the confe...

Neuroendocrine regulation of appetitive ingestive behavior

OpenAIRE

Keen-Rhinehart, Erin; Ondek, Katelynn; Schneider, Jill E.

2013-01-01

Food availability in nature is often irregular, and famine is commonplace. Increased motivation to engage in ingestive behaviors increases the chance of survival, providing additional potential opportunities for reproduction. Because of the advantages conferred by entraining ingestive behavior to environmental conditions, neuroendocrine mechanisms regulating the motivation to acquire and ingest food have evolved to be responsive to exogenous (i.e., food stored for future consumption) and endo...

Effect of metallurgical factors on the magnetic properties of non-oriented electrical steels under PWM excitation

International Nuclear Information System (INIS)

Tanaka, T.; Yashiki, H.; Takada, S.; Sasaki, T.

1994-01-01

Magnetic properties of non-oriented electrical steel sheets under PWM voltage excitation as well as those under sinusoidal excitation have been investigated from a metallurgical point of view. The core loss under PWM excitation is slightly larger than that under sinusoidal excitation. The induction dependence of the core loss difference between the two excitation conditions changes by changing Si content and grain size. The higher the induction, the larger the core loss difference of 0.2% Si steel with small grains. In the case of higher Si steels and 0.2% Si steel with large grain sizes, however, the core loss difference at inductions over 1.3 T decreases with increasing induction. At low induction levels the core loss difference has little relationship to the grain size. On the other hand, at high induction levels this difference decreases with increasing grain size. ((orig.))

Mentoring: An Evolving Relationship.

Science.gov (United States)

Block, Michelle; Florczak, Kristine L

2017-04-01

The column concerns itself with mentoring as an evolving relationship between mentor and mentee. The collegiate mentoring model, the transformational transcendence model, and the humanbecoming mentoring model are considered in light of a dialogue with mentors at a Midwest university and conclusions are drawn.

Nonsynonymous substitution rate (Ka is a relatively consistent parameter for defining fast-evolving and slow-evolving protein-coding genes

Directory of Open Access Journals (Sweden)

Wang Lei

2011-02-01

Full Text Available Abstract Background Mammalian genome sequence data are being acquired in large quantities and at enormous speeds. We now have a tremendous opportunity to better understand which genes are the most variable or conserved, and what their particular functions and evolutionary dynamics are, through comparative genomics. Results We chose human and eleven other high-coverage mammalian genome data–as well as an avian genome as an outgroup–to analyze orthologous protein-coding genes using nonsynonymous (Ka and synonymous (Ks substitution rates. After evaluating eight commonly-used methods of Ka and Ks calculation, we observed that these methods yielded a nearly uniform result when estimating Ka, but not Ks (or Ka/Ks. When sorting genes based on Ka, we noticed that fast-evolving and slow-evolving genes often belonged to different functional classes, with respect to species-specificity and lineage-specificity. In particular, we identified two functional classes of genes in the acquired immune system. Fast-evolving genes coded for signal-transducing proteins, such as receptors, ligands, cytokines, and CDs (cluster of differentiation, mostly surface proteins, whereas the slow-evolving genes were for function-modulating proteins, such as kinases and adaptor proteins. In addition, among slow-evolving genes that had functions related to the central nervous system, neurodegenerative disease-related pathways were enriched significantly in most mammalian species. We also confirmed that gene expression was negatively correlated with evolution rate, i.e. slow-evolving genes were expressed at higher levels than fast-evolving genes. Our results indicated that the functional specializations of the three major mammalian clades were: sensory perception and oncogenesis in primates, reproduction and hormone regulation in large mammals, and immunity and angiotensin in rodents. Conclusion Our study suggests that Ka calculation, which is less biased compared to Ks and Ka

Evolving spiking neural networks: a novel growth algorithm exhibits unintelligent design

Science.gov (United States)

Schaffer, J. David

2015-06-01

Spiking neural networks (SNNs) have drawn considerable excitement because of their computational properties, believed to be superior to conventional von Neumann machines, and sharing properties with living brains. Yet progress building these systems has been limited because we lack a design methodology. We present a gene-driven network growth algorithm that enables a genetic algorithm (evolutionary computation) to generate and test SNNs. The genome for this algorithm grows O(n) where n is the number of neurons; n is also evolved. The genome not only specifies the network topology, but all its parameters as well. Experiments show the algorithm producing SNNs that effectively produce a robust spike bursting behavior given tonic inputs, an application suitable for central pattern generators. Even though evolution did not include perturbations of the input spike trains, the evolved networks showed remarkable robustness to such perturbations. In addition, the output spike patterns retain evidence of the specific perturbation of the inputs, a feature that could be exploited by network additions that could use this information for refined decision making if required. On a second task, a sequence detector, a discriminating design was found that might be considered an example of "unintelligent design"; extra non-functional neurons were included that, while inefficient, did not hamper its proper functioning.

Metallurgical comparison between the experimental ED-ODS and commercial ODS steels

International Nuclear Information System (INIS)

Fernandez, P.; Serrano, M.; Lapena, J.

2007-01-01

Full text of publication follows: Recently, reduced activation oxide dispersion strengthened ferritic/martensitic steels have been identified as potential structural material candidates for first wall and blanket structures of fusion devices. These steels allow to increase the operation temperature of the fusion reactor, around of 100 deg. C or even more, because of their excellent thermal creep resistance. ODS steels are being developed and investigated for nuclear fission and fusion applications in Japan, Europe and the United States. Commercial ODS products, such as MA956 and PM2000 are available and are being used for high temperature applications. Since no reduced activation ferritic/martensitic steels are commercially available at present, the European Materials Fusion Programme has considered in the last years initiate adequate research activities to produce and characterize these materials to evaluate the feasibility of their use in the different blanket designs. Nowadays, the ODS steel that are being extensively investigated in Europe is the denominated EU-ODS. This alloy has the basic composition of the Eurofer'97 with 0.3% of Y 2 O 3 particles. In this paper, the metallurgical properties (microstructural, Charpy, etc) of the newly developed EU-ODS steel are presented and discussed together with the properties of the commercial MA956 and PM2000 ODS steels, also studied in this work, in order to show the differences and similarities between these ODS alloys. (authors)

Interactively Evolving Compositional Sound Synthesis Networks

DEFF Research Database (Denmark)

Jónsson, Björn Þór; Hoover, Amy K.; Risi, Sebastian

2015-01-01

the space of potential sounds that can be generated through such compositional sound synthesis networks (CSSNs). To study the effect of evolution on subjective appreciation, participants in a listener study ranked evolved timbres by personal preference, resulting in preferences skewed toward the first......While the success of electronic music often relies on the uniqueness and quality of selected timbres, many musicians struggle with complicated and expensive equipment and techniques to create their desired sounds. Instead, this paper presents a technique for producing novel timbres that are evolved...

Evolving effective incremental SAT solvers with GP

OpenAIRE

Bader, Mohamed; Poli, R.

2008-01-01

Hyper-Heuristics could simply be defined as heuristics to choose other heuristics, and it is a way of combining existing heuristics to generate new ones. In a Hyper-Heuristic framework, the framework is used for evolving effective incremental (Inc*) solvers for SAT. We test the evolved heuristics (IncHH) against other known local search heuristics on a variety of benchmark SAT problems.

Evolving and Controlling Perimeter, Rendezvous, and Foraging Behaviors in a Computation-Free Robot Swarm

Science.gov (United States)

2016-04-01

in extreme environments. Categories and Subject Descriptors I.2.11 [ Artificial Intelligence ]: Distributed Artificial In- telligence—multiagent systems...coherence and coordination; I.2.9 [ Artificial Intelligence ]: Robotics— intelligent vehi- cles Keywords swarm robotics, evolutionary algorithms...collective behaviors. Rubenstein et al. [12] studied how to collectively transport items using a simple control signals and behaviors. Others have looked

Consumer Behavior Research

Directory of Open Access Journals (Sweden)

Kaveh Peighambari

2016-04-01

Full Text Available This article analyzes 12 years of recent scholarly research on consumer behavior published in the five leading international journals in this field. Analyzing academic contributions to a specific area of research provides valuable insights into how it has evolved over a defined period. The approach was to briefly discuss content analysis and its application in scholarly literature review studies. The methodology used here involves the classification of topics to evaluate key trends in consumer behavior literature. It includes a ranking of topics published, typology of the published articles, the research classification in terms of methodologies, and analysis techniques. The most cited articles in the field and within each journal are also examined. The comprehensive literature review of consumer behavior research undertaken in this article could advance the discipline of consumer behavior research by elucidating the evolution of consumer behavior literature in the studied period.

Evolving Intelligent Systems Methodology and Applications

CERN Document Server

Angelov, Plamen; Kasabov, Nik

2010-01-01

From theory to techniques, the first all-in-one resource for EIS. There is a clear demand in advanced process industries, defense, and Internet and communication (VoIP) applications for intelligent yet adaptive/evolving systems. Evolving Intelligent Systems is the first self- contained volume that covers this newly established concept in its entirety, from a systematic methodology to case studies to industrial applications. Featuring chapters written by leading world experts, it addresses the progress, trends, and major achievements in this emerging research field, with a strong emphasis on th

Leadership Behaviors of Management for Complex Adaptive Systems

Science.gov (United States)

2010-04-01

Leadership Behaviors of Management for Complex Adaptive Systems Systems and Software Technology Conference April 2010 Dr. Suzette S. Johnson...2010 2. REPORT TYPE 3. DATES COVERED 00-00-2010 to 00-00-2010 4. TITLE AND SUBTITLE Leadership Behaviors of Management for Complex Adaptive...as they evolve – Control is dispersed and decentralized – Simple rules and governance used to direct behavior • Complexity Leadership Theory – Built on

Effects of CaO on the compaction and sintering by plasma of Powder-metallurgical iron

Science.gov (United States)

Ariza Suarez, H. G.; Sarmiento Santos, A.; Ortiz Otálora, C. A.

2017-12-01

This work the effect of the addition of Calcium Oxide (CaO) in the compaction and sintering of powder metallurgical iron Ancoor Steel 1000® is studied. Iron samples were made with proportions of: 0.5%, 1%, 1.5% and 2% by weight of CaO. The samples were sintered in a luminescent discharge furnace, in an atmosphere of H2+Ar at a temperature of 1150°C. XRD analysis was used to determine the formation of compounds, this analysis evidenced the formation of: hematite and magnetite, which were found both on the surface and in the volume. A characterization of the ability to protect against corrosive effects was carried out using the EIS electrochemical impedance spectroscopy method on the samples, in a solution of 1000ppm of chloride, with this procedure it was found that at a concentration of 0.5% and 1% CaO, the electrochemical impedance value is increased with values of 11.7MΩ, 2.2MΩ respectively.

Performance Analysis of a Grid-Connected Upgraded Metallurgical Grade Silicon Photovoltaic System

Directory of Open Access Journals (Sweden)

Chao Huang

2016-05-01

Full Text Available Because of their low cost, photovoltaic (PV cells made from upgraded metallurgical grade silicon (UMG-Si are a promising alternative to conventional solar grade silicon-based PV cells. This study investigates the outdoor performance of a 1.26 kW grid-connected UMG-Si PV system over five years, reporting the energy yields and performance ratio and estimating the long-term performance degradation rate. To make this investigation more meaningful, the performance of a mono-Si PV system installed at the same place and studied during the same period of time is presented for reference. Furthermore, this study systematizes and rationalizes the necessity of a data selection and filtering process to improve the accuracy of degradation rate estimation. The impact of plane-of-array irradiation threshold for data filtering on performance ratio and degradation rate is also studied. The UMG-Si PV system’s monthly performance ratio after data filtering ranged from 84% to 93% over the observation period. The annual degradation rate was 0.44% derived from time series of monthly performance ratio using the classical decomposition method. A comparison of performance ratio and degradation rate to conventional crystalline silicon-based PV systems suggests that performance of the UMG-Si PV system is comparable to that of conventional systems.

Assessment of the effect of Nd:YAG laser pulse operating parameters on the metallurgical characteristics of different tool steels using DOE software

Directory of Open Access Journals (Sweden)

T. Muhič

2011-04-01

Full Text Available To ensure the reliability of repair welded tool surfaces, clad quality should be improved. The relationships between metallurgical characteristics of cladding and laser input welding parameters were studied using the design of experiments software. The influence of laser power, welding speed, focal point position and diameter of welding wire on the weld-bead geometry (i.e. penetration, cladding zone width and heat-affected-zone width, microstructural homogeneity, dilution and bond strength was investigated on commonly used tool steels 1,2083, 1,2312 and 1,2343, using DOE software.

Methods Evolved by Observation

Science.gov (United States)

Montessori, Maria

2016-01-01

Montessori's idea of the child's nature and the teacher's perceptiveness begins with amazing simplicity, and when she speaks of "methods evolved," she is unveiling a methodological system for observation. She begins with the early childhood explosion into writing, which is a familiar child phenomenon that Montessori has written about…

Metallurgical analysis of high pressure gas pipelines rupture

International Nuclear Information System (INIS)

Hasan, F.; Ahmed, F.

2007-01-01

On 6 July 2004, two parallel-running gas pipelines (18-inch and 24-inch diameters), in the main transmission network of SNGPL (a gas company in Pakistan) were ruptured. The ruptures occurred in the early hours of the morning about 8 miles downstream of the compressor station AC-4. The ruptures were indicated by the increased gas flow at the outlet of AC-4 (1), first at about 0648 hours and then again about 20 minutes later. The gas escaping from the ruptured lines had caught fire, and the flames had also 'affected' a third parallel-running pipeline of 30-inch diameter, lying next to the 24-inch line. The metallurgical examination of the two ruptured lines showed that the 24-inch line was ruptured with the help of an explosive device that had been placed on the underside of the pipe. An examination of the 18-inch line showed that this pipe had failed as a result of the heating of the pipe-wall, presumably, by the flame emanating from the 24-inch line. These two observations clearly suggested that the 24-inch line was the first to rupture (by explosives), and the fire following this rupture had heated the 18-inch pipe to a temperature where its yield strength was unable to support the inside gas pressure. The 20 minutes time interval between the two ruptures was obviously the time taken by the 18 inch pipe to be heated upto the level where it started to yield. The 30-inch line lying next to the 24-inch line was affected to the extent that its coating had been burnt-off over a length of about 40-50 feet. However, the pipe did not exhibit any signs of deshaping or deformation what-so-ever. A replica metallographic examination indicated that the microstructure of the pipe was not measurably affected by the heat. It was thus decided not to replace the affected part of the 30-inch pipe, but only to re-coat this affected portion. (author)

Energy rational and economic use in a metallurgical industry: opportunity for replacing electricity by natural gas; Uso racional e economico da energia dentro de uma industria metalurgica: oportunidade de troca de eletricidade para gas natural

Energy Technology Data Exchange (ETDEWEB)

Galvao, Luiz Claudio Ribeiro; Kanayama, Paulo Helio; Udaeta, Miguel Edgar Morales [Universidade de Sao Paulo (USP), SP (Brazil). Escola Politecnica]. E-mail: lcgalvao@pea.usp.br; paulo.kanayama@poli.usp.br; udaeta@pea.usp.br; Rocha, Cidar Ramon Oliva; Affonso, Octavio Ferreira [Universidade de Sao Paulo (USP), SP (Brazil). Inst. de Eletrotecnica e Energia (IEE)]. E-mail: cidar_2001@yahoo.com; octavio@pea.usp.br

2006-07-01

This paper presents an initial diagnostic on the economic and efficient use of the energy input in metallurgical industries using electrical furnaces. From the foundations of modern energy management and industry characterization the electricity consumption is evaluated for presenting the facility with the energy change to natural gas and the modern methods of complete combustion with oxygen from the air. Taking into consideration the characteristics of real metallurgical industry production, the dimensioning of a natural gas furnace were calculated for replacing the existent electric furnace, with growing margin in the demand. The paper allows to conclude the the possibility is real, also considering the possibility of using the modern methods of co-generation for a complete use of gas which would imply in additional investment to produce electric energy by using a steam turbine.

Evolving Lattices for Analyzing Behavioral Dynamics of Characters in Literary Text

Directory of Open Access Journals (Sweden)

Eugene S Kitamura

2011-10-01

Full Text Available This paper is about an application of rough set derived lattices in order to analyze the dynamics of literary text. Due to the double approximation nature of rough set theory, a pseudo-closure obtained from two different equivalence relations allows us to form arbitrary lattices. Moreover, such double approximations with different equivalence relations permit us to obtain lattice fixed points based on two interpretations. The two interpretations used for literary text analysis are subjects and their attributes. The attributes chosen for this application are verbs. The progression of a story is defined by the sequence of verbs (or event occurrences. By fixing a window size and sliding the window down the story steps, we obtain a lattice representing the relationship between subjects and their attributes within that window frame. The resulting lattice provides information such as complementarity (lattice complement existence rate and distributivity (lattice complement possession rate. These measurements depend on the overlap and the lack of overlap among the attributes of characters. As the story develops and new character and attributes are provided as the source of lattices, one can observe its evolution. In fact, a dramatic change in the behavior dynamics in a scene is reflected in the particular shifts in the character-attribute relationship. This method lets us quantify the developments of character behavioral dynamics in a story.

Determination of nanoscale particles in the air of working zone at the metallurgical production

Directory of Open Access Journals (Sweden)

Т.S. Ulanova

2015-03-01

Full Text Available The results of studies of the air of working zone at the metallurgical production on the example of Avisma OJSC (Berezniki, the Perm Territory for the content of nanoscale particles are specified. The maximum nanoparticles concentration in the range of 13523–28609 mln./m3 is determined at the working place of the titanium production smelter with the maximum size of particles of 10–15 nm. At the working place in the administrative building (reference working place the maximum concentration is determined within the range of 524–1000 mln./m3; the maximum size of nanoparticles is 20 nm. It was established that the number concentration of nanoparticles at the reference working places (administration of Avisma OJSC is significantly lower than at the working places of main production processes. The presented studies can be used as the additional factors in the assessment of labor conditions and occupational risk during the manufacture and use of materials containing nanoparticles as well as the production processes with the nanoparticles formation.

Production of highly porous glass-ceramics from metallurgical slag, fly ash and waste glass

Directory of Open Access Journals (Sweden)

Mangutova Bianka V.

2004-01-01

Full Text Available Glass-ceramics composites were produced based on fly-ash obtained from coal power stations, metallurgical slag from ferronickel industry and waste glass from TV monitors, windows and flasks. Using 50% waste flask glass in combination with fly ash and 20% waste glass from TV screens in combination with slag, E-modulus and bending strength values of the designed systems are increased (system based on fly ash: E-modulus from 6 to 29 GPa, and bending strength from 9 to 75 MPa. The polyurethane foam was used as a pore creator which gave the material porosity of 70(5% (fly ash-glass composite and a porosity of 65( 5% (slag-glass composite. E-modulus values of the designed porous systems were 3.5(1.2 GPa and 8.1(3 GPa, while the bending strength values were 6.0(2 MPa and 13.2(3.5 MPa, respectively. These materials could be used for the production of tiles, wall bricks, as well as for the construction of air diffusers for waste water aeration.

Metallurgical and Mechanical Characterization of High Temperature Titanium Alloys Joined by Friction Stir Welding

Science.gov (United States)

Gangwar, Kapil Dev

flow has been done by scanning electron microscopy (SEM), and electron dispersive spectroscopy (EDS). Hardness profiles on the transverse cross section of the weld have been measured in order to relate the deformation of main constituents, α {hexagonal close packed (hcp)}, and β {body centered cubic (bcc)} that provides a new paradigm into grain refinement mechanism. Material flow and evolving microstructure along with distribution of corresponding elements distribution was characterized by SEM, and EDS respectively. For the case of dissimilar alloys (Ti-6242 & Ti-54M, and Ti-6242 & Ti-64 ) a necklace shaped macrostructure has been observed in the WN consisting of untransformed α migrating from the side of Ti-6242, and of basket-weave morphology (prior β grains transforming into α+β decorated with grain boundary α) of Ti-54M. Microhardness characterization undoubtedly reveals distinct boundaries between weld nugget and parent material. However, to understand the constitutive behavior of the thermo mechanically affected zone (TMAZ) on the advancing side (ADV), or retreating side (RET) and of WN, digital image correlation (DIC) technique has been adapted to develop strain maps in transverse tensile specimens. Improved mechanical properties of TMAZ on the ADV in comparison with RET TMAZ are in accordance with hardness values. Occurrence of fracture on the RET side, and morphology of the fractured surface have also been discussed. Based on the fractured morphology, it can be said that the presence of distinct and clustered island like morphologies in the form of transcrystalline and intercrystalline fracture is a results of microstructure that evolves due to difference in β transus temperature of two alloys. The mechanical properties are analyzed and discussed in that regard. Evolving volume fraction of phases along with their crystallographic orientation has also been elucidated. Evolution of texture has been discussed in terms of (100)_α,(002)_α,(110)_β,(101

[Strut fracture of a convex-concave 60 degree Björk-Shiley mitral valve prosthesis 5 years after implantation--metallurgic analysis of the prosthesis strut].

Science.gov (United States)

Lemke, B; Rathmann, J; Wiebe, V; Witzel, U

1991-08-01

Acute mechanical failure of prosthetic heart valves is rare, but associated with high mortality when occurring. For convexo-concave Björk-Shiley prostheses only fractures of the outlet strut are reported. We present a case of lethal mechanical complication 5 years after implantation. By additional metallurgic analysis we were able to identify a sequential course of the outlet strut fracture. This could lead to new approaches for early detection of this complication.

Evolutionary Dynamics of Collective Behavior Selection and Drift: Flocking, Collapse, and Oscillation.

Science.gov (United States)

Tan, Shaolin; Wang, Yaonan; Chen, Yao; Wang, Zhen

2016-06-14

Behavioral choice is ubiquitous across a wide range of interactive decision-making processes and a myriad of scientific disciplines. With regard to this issue, one entitative problem is actually to understand how collective social behaviors form and evolve among populations when they face a variety of conflict alternatives. In this paper, a selection-drift dynamic model is formulated to characterize the behavior imitation and exploration processes in social populations. Based on the proposed framework, several typical behavior evolution patterns, including behavioral flocking, collapse, and oscillation, are reproduced with different kinds of behavior networks. Interestingly, for the selection-drift dynamics on homogeneous symmetric behavior networks, we unveil the phase transition from behavioral flocking to collapse and derive the bifurcation diagram of the evolutionary stable behaviors in social behavior evolution. While via analyzing the survival conditions of the best behavior on heterogeneous symmetric behavior networks, we propose a selection-drift mechanism to guarantee consensus at the optimal behavior. Moreover, when the selection-drift dynamics on asymmetric behavior networks is simulated, it is shown that breaking the symmetry in behavior networks can induce various behavioral oscillations. These obtained results may shed new insights into understanding, detecting, and further controlling how social norm and cultural trends evolve.

Copper processing in Vinča: New contributions to the thesis about metallurgical character of Vinča culture

Directory of Open Access Journals (Sweden)

Antonović Dragana A.

2002-01-01

Full Text Available Abundant hand written documentation from excavations of Vinča (1908–1934 offers sufficient evidence that confirms the thesis established by investigator of Vinča M. M. Vasić himself that Vinča was metallurgical center. After comparing these data with the finds related to early copper processing on other sites of the central Balkans (Belovode, Pločnik, Gornja Tuzla, Fafos, Selevac it could be assumed that Vinča culture was acquainted with metallurgy from its very outset. This assumption is supported by similar finds from other sides of the world (Tymna, Chinflon, Batán Grande and even more so the results of experimental copper processing.

Evolving artificial metalloenzymes via random mutagenesis

Science.gov (United States)

Yang, Hao; Swartz, Alan M.; Park, Hyun June; Srivastava, Poonam; Ellis-Guardiola, Ken; Upp, David M.; Lee, Gihoon; Belsare, Ketaki; Gu, Yifan; Zhang, Chen; Moellering, Raymond E.; Lewis, Jared C.

2018-03-01

Random mutagenesis has the potential to optimize the efficiency and selectivity of protein catalysts without requiring detailed knowledge of protein structure; however, introducing synthetic metal cofactors complicates the expression and screening of enzyme libraries, and activity arising from free cofactor must be eliminated. Here we report an efficient platform to create and screen libraries of artificial metalloenzymes (ArMs) via random mutagenesis, which we use to evolve highly selective dirhodium cyclopropanases. Error-prone PCR and combinatorial codon mutagenesis enabled multiplexed analysis of random mutations, including at sites distal to the putative ArM active site that are difficult to identify using targeted mutagenesis approaches. Variants that exhibited significantly improved selectivity for each of the cyclopropane product enantiomers were identified, and higher activity than previously reported ArM cyclopropanases obtained via targeted mutagenesis was also observed. This improved selectivity carried over to other dirhodium-catalysed transformations, including N-H, S-H and Si-H insertion, demonstrating that ArMs evolved for one reaction can serve as starting points to evolve catalysts for others.

Metallurgical study of the iberian weapons found in jutia valley (Nerpio-Yeste, Albacete, Spain. Work, weaponry, rituals and mountain communities

Directory of Open Access Journals (Sweden)

Marc Gener Moret

2016-11-01

Full Text Available We present a metallurgical study of weapons of the Iberian Iron Age documented in the high-altitude valley of Jutia (Nerpio-Yeste, Albacete, Spain integrated in the analysis of their specific archaeological context and as part of our ongoing research about the forms of organization of mountain landscapes during the Iron Age. The results are especially valid in the case of a soliferreum, whose metallographic analysis allows us to characterize the technology of its production process, and a lance tip, whose analysis raises arguments about the complex social life and the various social actions potentially linked to the objects placed in ritual and funerary contexts.

Restoration in a mining and metallurgical industries area as a model project. Subproject 1: Factory for amalgamation Halsbruecke. Final report; Modellhafte Sanierung in einer Region mit Bergbau- und Huettenindustrie. Teilvorhaben 1: Amalgamierwerk Halsbruecke, Land Sachsen. Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Cichos, C.; Menzer, V.; Schaal, A.

1993-06-01

Technology development for the restoration of a metallurgical site contaminated by heavy metals (Pb, Zn, Cu, Hg, As) with the aims of far-reaching recycling as well as minimizing of residues and demonstration of this technology contains in a first step - detailed historical exploration; - chemical, physical and mineralogical materials analysis; - bench scale investigations for process engineering. Starting from historical appraisal and geogene/anthropogene conditions the methods of material characterization bring statements on processing of noxious materials (metallurgical), harmless dumping abilities (immobilization, stabilization) and technological process stages (particularly wet mechanical processes). The same methodology is useful for analogous mining, metallurgical and used material sites with contamination by heavy metals and consisting of heterogeneous materials. (orig.) [Deutsch] Die modellhafte Technologieentwicklung und die Demonstration dieser Technologie zur Sanierung eines durch Schwermetalle (Pb, Zn, Cu, Cd, Hg, As) komplex belasteten Huettenstandortes unter dem Aspekt einer weitgehenden Reststoffverwertung sowie Minimierung der zu entsorgenden Rueckstaende umfasst in der ersten Phase - eine detaillierte historische Analyse/Erkundung; - eine chemische, physikalische und mineralogische Stoffcharakterisierung; verfahrenstechnische Untersuchungen im Labormassstab. Ausgehend von der historischen Bewertung und der geogenen/anthropogenen Verhaeltnisse fuehren die Methoden der Stoffcharakterisierung zu Aussagen der Schadstoffweiterverarbeitung (metallurgisch) sowie der gefahrlosen Deponierung (Immobilisierung, Stabilisierung) und zu technologischen Verfahrensschritten (bes. nassmechanische Verfahren). Die Herangehensweise ist fuer analoge Bergbau- aber besonders Huettenstandorte ggf. auch fuer andere Altlastenstandorte mit komplexer Schwermetallkontamination und heterogenem Material relevant. (orig.)

Metallurgical recovery of metals from electronic waste: A review

International Nuclear Information System (INIS)

Cui Jirang; Zhang Lifeng

2008-01-01

Waste electric and electronic equipment, or electronic waste, has been taken into consideration not only by the government but also by the public due to their hazardous material contents. In the detailed literature survey, value distributions for different electronic waste samples were calculated. It is showed that the major economic driver for recycling of electronic waste is from the recovery of precious metals. The state of the art in recovery of precious metals from electronic waste by pyrometallurgical processing, hydrometallurgical processing, and biometallurgical processing are highlighted in the paper. Pyrometallurgical processing has been a traditional technology for recovery of precious metals from waste electronic equipment. However, state-of-the-art smelters are highly depended on investments. Recent research on recovery of energy from PC waste gives an example for using plastics in this waste stream. It indicates that thermal processing provides a feasible approach for recovery of energy from electronic waste if a comprehensive emission control system is installed. In the last decade, attentions have been removed from pyrometallurgical process to hydrometallurgical process for recovery of metals from electronic waste. In the paper, hydrometallurgical processing techniques including cyanide leaching, halide leaching, thiourea leaching, and thiosulfate leaching of precious metals are detailed. In order to develop an environmentally friendly technique for recovery of precious metals from electronic scrap, a critical comparison of main leaching methods is analyzed for both economic feasibility and environmental impact. It is believed that biotechnology has been one of the most promising technologies in metallurgical processing. Bioleaching has been used for recovery of precious metals and copper from ores for many years. However, limited research was carried out on the bioleaching of metals from electronic waste. In the review, initial researches on the

Metal mobilization from metallurgical wastes by soil organic acids.

Science.gov (United States)

Potysz, Anna; Grybos, Malgorzata; Kierczak, Jakub; Guibaud, Gilles; Fondaneche, Patrice; Lens, Piet N L; van Hullebusch, Eric D

2017-07-01

Three types of Cu-slags differing in chemical and mineralogical composition (historical, shaft furnace, and granulated slags) and a matte from a lead recovery process were studied with respect to their susceptibility to release Cu, Zn and Pb upon exposure to organic acids commonly encountered in soil environments. Leaching experiments (24-960 h) were conducted with: i) humic acid (20 mg/L) at pH t 0  = 4.4, ii) fulvic acid (20 mg/L) at pH t 0  = 4.4, iii) an artificial root exudates (ARE) (17.4 g/L) solution at pH t 0  = 4.4, iv) ARE solution at pH t 0  = 2.9 and v) ultrapure water (pH t 0  = 5.6). The results demonstrated that the ARE contribute the most to the mobilization of metals from all the wastes analyzed, regardless of the initial pH of the solution. For example, up to 14%, 30%, 24% and 5% of Cu is released within 960 h from historical, shaft furnace, granulated slags and lead matte, respectively, when exposed to the artificial root exudates solution (pH 2.9). Humic and fulvic acids were found to have a higher impact on granulated and shaft furnace slags as compared to the ultrapure water control and increased the release of metals by a factor up to 37.5 (Pb) and 20.5 (Cu) for granulated and shaft furnace slags, respectively. Humic and fulvic acids amplified the mobilization of metals by a maximal factor of 13.6 (Pb) and 12.1 (Pb) for historical slag and lead matte, respectively. The studied organic compounds contributed to different release rates of metallic contaminants from individual metallurgical wastes under the conditions tested. Copyright © 2017 Elsevier Ltd. All rights reserved.

Metallurgical recovery of metals from electronic waste: A review

Energy Technology Data Exchange (ETDEWEB)

Cui Jirang [Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), Alfred Getz vei 2, N-7491 Trondheim (Norway)], E-mail: Jirang.Cui@material.ntnu.no; Zhang Lifeng [Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), Alfred Getz vei 2, N-7491 Trondheim (Norway)], E-mail: zhanglife@mst.edu

2008-10-30

Waste electric and electronic equipment, or electronic waste, has been taken into consideration not only by the government but also by the public due to their hazardous material contents. In the detailed literature survey, value distributions for different electronic waste samples were calculated. It is showed that the major economic driver for recycling of electronic waste is from the recovery of precious metals. The state of the art in recovery of precious metals from electronic waste by pyrometallurgical processing, hydrometallurgical processing, and biometallurgical processing are highlighted in the paper. Pyrometallurgical processing has been a traditional technology for recovery of precious metals from waste electronic equipment. However, state-of-the-art smelters are highly depended on investments. Recent research on recovery of energy from PC waste gives an example for using plastics in this waste stream. It indicates that thermal processing provides a feasible approach for recovery of energy from electronic waste if a comprehensive emission control system is installed. In the last decade, attentions have been removed from pyrometallurgical process to hydrometallurgical process for recovery of metals from electronic waste. In the paper, hydrometallurgical processing techniques including cyanide leaching, halide leaching, thiourea leaching, and thiosulfate leaching of precious metals are detailed. In order to develop an environmentally friendly technique for recovery of precious metals from electronic scrap, a critical comparison of main leaching methods is analyzed for both economic feasibility and environmental impact. It is believed that biotechnology has been one of the most promising technologies in metallurgical processing. Bioleaching has been used for recovery of precious metals and copper from ores for many years. However, limited research was carried out on the bioleaching of metals from electronic waste. In the review, initial researches on the

Cooperation in the field of materials and metallurgical technologies

International Nuclear Information System (INIS)

Pilous, V.; Kletecka, Z.; Matejovic, K.

1989-01-01

The SKODA Works cooperate extensively with the Mechanical and Electrical Engineering College in Plzen and with other organizations in many branches of science and technology, among others in the field of materials science and metallurgical technologies. For instance, the technology was mastered of welding low-pressure rotors from a medium-alloy high-strength steel with reduced carbon content of the CrNiMoV type, with yield points of 600 MPa in the basic material and 550 MPa in the welded joint. The welded rotor is used in three low-pressure parts of a 1000 MW steam turbine for a nuclear power plant, which is also produced at SKODA. Problems of protection against corrosion and erosion in saturated steam turbines, caused by wet steam at pressures of 0.5 to 5 MPa and humidity as high as 11%, were also solved. A complex of problems was tackled in the production of reactor pressure vessels. It was found that heat treatment of 25Cr/13Ni overlays of the CrMoV reactor steel at 665 degC results in the formation of a carburized zone between the overlay and the CrMoV steel. This zone constituted a good barrier against the diffusion of hydrogen from the austenitic overlay to the steel. The width of the zone where the diffusion had taken place did not increase in the working conditions, i.e. under the effect of a temperature of 320 degC, while the hardness of this zone increased considerably due to the redistribution of carbon within the 1.6 μm width. The occurrence of the carburized high-hardness zone had a favourable effect on the stabilization of the rate of crack propagation and on its diversion. Recovery annealing at 480 degC is suitable for reducing the hydrogen content of the austenitic overlays. (P.A.). 5 figs., 14 refs

Metallurgical factors that contribute to cracking in BWR piping

International Nuclear Information System (INIS)

Weeks, J.R.

1975-01-01

During the fall of 1974 and early winter of 1975, cracks have been discovered in the 4 in. bypass lines of several Boiling Water Reactors (BWR's) in the United States. Further, similar cracks were discovered at two BWR's in Japan during the same period. More recently, cracks have been discovered in the core spray piping and in a furnace-sensitized ''safe end'' and adjacent ''dutchman'' at the Dresden Nuclear Power Station, Unit No. 2. Although inspections at all other U.S. BWR's have not disclosed further instances of cracking in core spray piping, leaking cracks have been found in the core spray piping of two BWR's overseas. Metallurgical examinations of these cracks are not yet complete. The following observations have been made to date. All cracks (except those in the furnace-sensitized safe end and dutchman) occurred in seamless type 304 stainless steel piping or in elbows fabricated from such piping, in the outer heat affected zone of either field or shop welds, in lines isolated from the main primary coolant flow during full power operation, except for the not yet examined cracks in the Monticello bypass lines. The cracks are exclusively intergranular, and occur in metal that has been lightly sensitized by the welding process, with only intermittent grain boundary carbides. They developed in the areas of peak axial residual stresses from welding rather than in the most heavily sensitized areas. No fatigue striations have been found on the fracture surfaces. The evidence received to date strongly indicates that these cracks were caused by intergranular stress corrosion of weld-sensitized stainless steel by BWR water containing greater than 0.2 ppM oxygen. The possible role of fatigue or alternating stresses in this corrosion is not clear. Further, not all the cracks detected to date necessarily have occurred by the same mechanism

The evolution of resource adaptation: how generalist and specialist consumers evolve.

Science.gov (United States)

Ma, Junling; Levin, Simon A

2006-07-01

Why and how specialist and generalist strategies evolve are important questions in evolutionary ecology. In this paper, with the method of adaptive dynamics and evolutionary branching, we identify conditions that select for specialist and generalist strategies. Generally, generalist strategies evolve if there is a switching benefit; specialists evolve if there is a switching cost. If the switching cost is large, specialists always evolve. If the switching cost is small, even though the consumer will first evolve toward a generalist strategy, it will eventually branch into two specialists.

Ranking in evolving complex networks

Science.gov (United States)

Liao, Hao; Mariani, Manuel Sebastian; Medo, Matúš; Zhang, Yi-Cheng; Zhou, Ming-Yang

2017-05-01

Complex networks have emerged as a simple yet powerful framework to represent and analyze a wide range of complex systems. The problem of ranking the nodes and the edges in complex networks is critical for a broad range of real-world problems because it affects how we access online information and products, how success and talent are evaluated in human activities, and how scarce resources are allocated by companies and policymakers, among others. This calls for a deep understanding of how existing ranking algorithms perform, and which are their possible biases that may impair their effectiveness. Many popular ranking algorithms (such as Google's PageRank) are static in nature and, as a consequence, they exhibit important shortcomings when applied to real networks that rapidly evolve in time. At the same time, recent advances in the understanding and modeling of evolving networks have enabled the development of a wide and diverse range of ranking algorithms that take the temporal dimension into account. The aim of this review is to survey the existing ranking algorithms, both static and time-aware, and their applications to evolving networks. We emphasize both the impact of network evolution on well-established static algorithms and the benefits from including the temporal dimension for tasks such as prediction of network traffic, prediction of future links, and identification of significant nodes.

Employment and other selected personnel attributes in metallurgical and industrial enterprises of different size - research results

Directory of Open Access Journals (Sweden)

A. Pawliczek

2015-10-01

Full Text Available The presented paper deals with the issue of employment and other selected personnel attributes as employees’ affiliations, employees’ benefits, monitoring of employees’ satisfaction, monitoring of work productivity, investments into employees education and obstacles in hiring qualified human resources. The characteristics are benchmarked on the background of enterprise size based on the employees count in the year 2013. The relevant data were collected in Czech industrial enterprises, including metallurgical companies, with the help of university questionnaire research in order to induce synergy effect arising from mutual communication of academy-students-industry. The most important results are presented later in the paper, complemented with discussion based on relevant professional literature sources. The findings suggest that bigger companies check productivity and satisfaction and dismiss employees more frequently, unlike medium companies which do not reduce their workforce and solve the impact of crisis by decreased affiliations, reduced benefits and similar savings.

Adaptation of Escherichia coli to glucose promotes evolvability in lactose.

Science.gov (United States)

Phillips, Kelly N; Castillo, Gerardo; Wünsche, Andrea; Cooper, Tim F

2016-02-01

The selective history of a population can influence its subsequent evolution, an effect known as historical contingency. We previously observed that five of six replicate populations that were evolved in a glucose-limited environment for 2000 generations, then switched to lactose for 1000 generations, had higher fitness increases in lactose than populations started directly from the ancestor. To test if selection in glucose systematically increased lactose evolvability, we started 12 replay populations--six from a population subsample and six from a single randomly selected clone--from each of the six glucose-evolved founder populations. These replay populations and 18 ancestral populations were evolved for 1000 generations in a lactose-limited environment. We found that replay populations were initially slightly less fit in lactose than the ancestor, but were more evolvable, in that they increased in fitness at a faster rate and to higher levels. This result indicates that evolution in the glucose environment resulted in genetic changes that increased the potential of genotypes to adapt to lactose. Genome sequencing identified four genes--iclR, nadR, spoT, and rbs--that were mutated in most glucose-evolved clones and are candidates for mediating increased evolvability. Our results demonstrate that short-term selective costs during selection in one environment can lead to changes in evolvability that confer longer term benefits. © 2016 The Author(s). Evolution © 2016 The Society for the Study of Evolution.

Evolving fuzzy rules for relaxed-criteria negotiation.

Science.gov (United States)

Sim, Kwang Mong

2008-12-01

In the literature on automated negotiation, very few negotiation agents are designed with the flexibility to slightly relax their negotiation criteria to reach a consensus more rapidly and with more certainty. Furthermore, these relaxed-criteria negotiation agents were not equipped with the ability to enhance their performance by learning and evolving their relaxed-criteria negotiation rules. The impetus of this work is designing market-driven negotiation agents (MDAs) that not only have the flexibility of relaxing bargaining criteria using fuzzy rules, but can also evolve their structures by learning new relaxed-criteria fuzzy rules to improve their negotiation outcomes as they participate in negotiations in more e-markets. To this end, an evolutionary algorithm for adapting and evolving relaxed-criteria fuzzy rules was developed. Implementing the idea in a testbed, two kinds of experiments for evaluating and comparing EvEMDAs (MDAs with relaxed-criteria rules that are evolved using the evolutionary algorithm) and EMDAs (MDAs with relaxed-criteria rules that are manually constructed) were carried out through stochastic simulations. Empirical results show that: 1) EvEMDAs generally outperformed EMDAs in different types of e-markets and 2) the negotiation outcomes of EvEMDAs generally improved as they negotiated in more e-markets.

DrawCompileEvolve: Sparking interactive evolutionary art with human creations

DEFF Research Database (Denmark)

Zhang, Jinhong; Taarnby, Rasmus; Liapis, Antonios

2015-01-01

This paper presents DrawCompileEvolve, a web-based drawing tool which allows users to draw simple primitive shapes, group them together or define patterns in their groupings (e.g. symmetry, repetition). The user’s vector drawing is then compiled into an indirectly encoded genetic representation......, which can be evolved interactively, allowing the user to change the image’s colors, patterns and ultimately transform it. The human artist has direct control while drawing the initial seed of an evolutionary run and indirect control while interactively evolving it, thus making DrawCompileEvolve a mixed...

Corrosion behavior of Zircaloy 4 cladding material. Evaluation of the hydriding effect

International Nuclear Information System (INIS)

Blat, M.

1997-04-01

In this work, particular attention has been paid to the hydriding effect in PIE and laboratory test to validate a detrimental hydrogen contribution on Zircaloy 4 corrosion behavior at high burnup. Laboratory corrosion tests results confirm that hydrides have a detrimental role on corrosion kinetics. This effect is particularly significant for cathodic charged samples with a massive hydride outer layer before corrosion test. PIE show that at high burnup a hydride layer is formed underneath the metal/oxide interface. The results of the metallurgical examinations are discussed with respect to the possible mechanisms involved in this detrimental effect of hydrogen. Therefore, according to the laboratory tests results and PIE, hydrogen could be a strong contributor to explain the increase in corrosion rate at high burnup. (author)

Behavior of small ferromagnetic particles in traveling magnetic field

Science.gov (United States)

Deych, V. G.; Terekhov, V. P.

1985-03-01

Forces and moments acting on a magnetizable body in a traveling magnetic field are calculated for a body with dimensions much smaller than the wavelength of the magnetic field. It is assumed that a particle of given linear dimension does not have a constant magnetic moment. The material of a particle is characterized by its magnetic permeability and electrical conductivity. The hypothesis that rotation plays a major role in the behavior of small particles is confirmed and the fact that a small particle rolls on a plane, without sliding, when the surface is perfectly rough, in the opposite direction from which the magnetic field travels is explained. Calculations are based on the magnetohydrodynamic equations for a quasi steady magnetic field, and the induced Foucault eddy currents are considered. The results are applicable to transport of ferrofluids and to such metallurgical devices as separators.

Evolving application of biomimetic nanostructured hydroxyapatite

Directory of Open Access Journals (Sweden)

Norberto Roveri

2010-11-01

Full Text Available Norberto Roveri, Michele IafiscoLaboratory of Environmental and Biological Structural Chemistry (LEBSC, Dipartimento di Chimica ‘G. Ciamician’, Alma Mater Studiorum, Università di Bologna, Bologna, ItalyAbstract: By mimicking Nature, we can design and synthesize inorganic smart materials that are reactive to biological tissues. These smart materials can be utilized to design innovative third-generation biomaterials, which are able to not only optimize their interaction with biological tissues and environment, but also mimic biogenic materials in their functionalities. The biomedical applications involve increasing the biomimetic levels from chemical composition, structural organization, morphology, mechanical behavior, nanostructure, and bulk and surface chemical–physical properties until the surface becomes bioreactive and stimulates cellular materials. The chemical–physical characteristics of biogenic hydroxyapatites from bone and tooth have been described, in order to point out the elective sides, which are important to reproduce the design of a new biomimetic synthetic hydroxyapatite. This review outlines the evolving applications of biomimetic synthetic calcium phosphates, details the main characteristics of bone and tooth, where the calcium phosphates are present, and discusses the chemical–physical characteristics of biomimetic calcium phosphates, methods of synthesizing them, and some of their biomedical applications.Keywords: hydroxyapatite, nanocrystals, biomimetism, biomaterials, drug delivery, remineralization

Behavioral fluency: Evolution of a new paradigm

OpenAIRE

Binder, Carl

1996-01-01

Behavioral fluency is that combination of accuracy plus speed of responding that enables competent individuals to function efficiently and effectively in their natural environments. Evolving from the methodology of free-operant conditioning, the practice of precision teaching set the stage for discoveries about relations between behavior frequency and specific outcomes, notably retention and maintenance of performance, endurance or resistance to distraction, and application or transfer of tra...

Metallurgical investigation of disc cracking in the LP-2 turbine at a nuclear power station. Final report

International Nuclear Information System (INIS)

Burghard, H.C.

1982-07-01

An investigation of combined face cracking and rim cracking in discs of an LP steam turbine rotor was performed. The incident in question involved the development of major cracks in the hub/web transition on the outlet face of the disc as well as major cracking of the blade attachment steeples. Both types of cracking occurred in the No. 1 discs at both ends of a particular rotor. The program was based on a metallurgical evaluation of hub and rim samples of discs removed from the turbine rotor after approximately 31,000 hours of operation. In-depth metallographic and fractographic examinations of representative face cracks and rim cracks were conducted. In addition, the mechanical properties and chemical composition of each of the disc samples were determined. Analyses of crack surface deposits and bulk turbine deposits were also performed

Nuclear methods on service of mountain manufacture Navoi Mining-Metallurgical complex

International Nuclear Information System (INIS)

Kucherskiy, N.I.

2004-01-01

Full text: On a number of the major minerals, such as gold, uranium, copper, tungsten, potash salts, phosphorites, caolines, etc. Uzbekistan on the confirmed stocks and predicted resources occupies leading places among the states of the world. The basic deposits of gold and uranium are concentrated in Central-Kysylkum region, which is field of activity of Navoi mining-metallurgical combine. In industrial divisions of the combine, located in five areas of republic about 60000 persons are engaged. At all stages of manufacture of gold (since investigation) analytical maintenance has extremely important role. In NMMC radioanalytical methods are widely used, in particular, on mine 'Muruntau' the unique gamma-activation analysis laboratory has been constructed and entered into operation. For the period of operation of laboratory, i.e. since 1977, it is executed more than nine millions analyses of geological tests with extremely high expressness (about tens seconds). It is used x-ray-radiometric method for large-portion (by dumper) sortings and on lumpy separation of ores. With the help of high-sensitivity radiometric means of measurements it is possible to develop phosphorites for reception of phosphoric fertilizers. Nuclear-physical methods are applied to the decision of other problems. Thus, due to application of nuclear-physical methods of the operative control of technological processes of mining manufacture, quality management of ores, the account of quantity of products of extraction and their preliminary enrichment, the actual problem - increase in profitability of all mining manufacture NMMC is solved

Finite element analysis of metallurgical phase transformations in AA 6056-T4 and their effects upon the residual stress and distortion states of a laser welded T-joint

International Nuclear Information System (INIS)

Zain-ul-abdein, Muhammad; Nelias, Daniel; Jullien, Jean-Francois; Boitout, Frederic; Dischert, Luc; Noe, Xavier

2011-01-01

Aircraft industry makes extensive use of aluminium alloy AA 6056-T4 in the fabrication of fuselage panels using laser beam welding technique. Since high temperatures are involved in the manufacturing process, the precipitation/dissolution occurrences are expected as solid state phase transformations. These transformations are likely to affect the residual distortion and stress states of the component. The present work investigates the effect of metallurgical phase transformations upon the residual stresses and distortions induced by laser beam welding in a T-joint configuration using the finite element method. Two separate models were studied using different finite element codes, where the first one describes a thermo-mechanical analysis using Abaqus; while the second one discusses a thermo-metallo-mechanical analysis using Sysweld. A comparative analysis of experimentally validated finite element models has been performed and the residual stress states with and without the metallurgical phase transformations are predicted. The results show that the inclusion of phase transformations has a negligible effect on predicted distortions, which are in agreement with the experimental data, but an effect on predicted residual stresses, although the experimentally measured residual stresses are not available to support the analyses.

Evolving Procurement Organizations

DEFF Research Database (Denmark)

Bals, Lydia; Laine, Jari; Mugurusi, Godfrey

Procurement has to find further levers and advance its contribution to corporate goals continuously. This places pressure on its organization in order to facilitate its performance. Therefore, procurement organizations constantly have to evolve in order to match these demands. A conceptual model...... and external contingency factors and having a more detailed look at the structural dimensions chosen, beyond the well-known characteristics of centralization, formalization, participation, specialization, standardization and size. From a theoretical perspective, it opens up insights that can be leveraged...

Laplacian Estrada and normalized Laplacian Estrada indices of evolving graphs.

Science.gov (United States)

Shang, Yilun

2015-01-01

Large-scale time-evolving networks have been generated by many natural and technological applications, posing challenges for computation and modeling. Thus, it is of theoretical and practical significance to probe mathematical tools tailored for evolving networks. In this paper, on top of the dynamic Estrada index, we study the dynamic Laplacian Estrada index and the dynamic normalized Laplacian Estrada index of evolving graphs. Using linear algebra techniques, we established general upper and lower bounds for these graph-spectrum-based invariants through a couple of intuitive graph-theoretic measures, including the number of vertices or edges. Synthetic random evolving small-world networks are employed to show the relevance of the proposed dynamic Estrada indices. It is found that neither the static snapshot graphs nor the aggregated graph can approximate the evolving graph itself, indicating the fundamental difference between the static and dynamic Estrada indices.

How does cognition evolve? Phylogenetic comparative psychology

Science.gov (United States)

Matthews, Luke J.; Hare, Brian A.; Nunn, Charles L.; Anderson, Rindy C.; Aureli, Filippo; Brannon, Elizabeth M.; Call, Josep; Drea, Christine M.; Emery, Nathan J.; Haun, Daniel B. M.; Herrmann, Esther; Jacobs, Lucia F.; Platt, Michael L.; Rosati, Alexandra G.; Sandel, Aaron A.; Schroepfer, Kara K.; Seed, Amanda M.; Tan, Jingzhi; van Schaik, Carel P.; Wobber, Victoria

2014-01-01

Now more than ever animal studies have the potential to test hypotheses regarding how cognition evolves. Comparative psychologists have developed new techniques to probe the cognitive mechanisms underlying animal behavior, and they have become increasingly skillful at adapting methodologies to test multiple species. Meanwhile, evolutionary biologists have generated quantitative approaches to investigate the phylogenetic distribution and function of phenotypic traits, including cognition. In particular, phylogenetic methods can quantitatively (1) test whether specific cognitive abilities are correlated with life history (e.g., lifespan), morphology (e.g., brain size), or socio-ecological variables (e.g., social system), (2) measure how strongly phylogenetic relatedness predicts the distribution of cognitive skills across species, and (3) estimate the ancestral state of a given cognitive trait using measures of cognitive performance from extant species. Phylogenetic methods can also be used to guide the selection of species comparisons that offer the strongest tests of a priori predictions of cognitive evolutionary hypotheses (i.e., phylogenetic targeting). Here, we explain how an integration of comparative psychology and evolutionary biology will answer a host of questions regarding the phylogenetic distribution and history of cognitive traits, as well as the evolutionary processes that drove their evolution. PMID:21927850

How does cognition evolve? Phylogenetic comparative psychology.

Science.gov (United States)

MacLean, Evan L; Matthews, Luke J; Hare, Brian A; Nunn, Charles L; Anderson, Rindy C; Aureli, Filippo; Brannon, Elizabeth M; Call, Josep; Drea, Christine M; Emery, Nathan J; Haun, Daniel B M; Herrmann, Esther; Jacobs, Lucia F; Platt, Michael L; Rosati, Alexandra G; Sandel, Aaron A; Schroepfer, Kara K; Seed, Amanda M; Tan, Jingzhi; van Schaik, Carel P; Wobber, Victoria

2012-03-01

Now more than ever animal studies have the potential to test hypotheses regarding how cognition evolves. Comparative psychologists have developed new techniques to probe the cognitive mechanisms underlying animal behavior, and they have become increasingly skillful at adapting methodologies to test multiple species. Meanwhile, evolutionary biologists have generated quantitative approaches to investigate the phylogenetic distribution and function of phenotypic traits, including cognition. In particular, phylogenetic methods can quantitatively (1) test whether specific cognitive abilities are correlated with life history (e.g., lifespan), morphology (e.g., brain size), or socio-ecological variables (e.g., social system), (2) measure how strongly phylogenetic relatedness predicts the distribution of cognitive skills across species, and (3) estimate the ancestral state of a given cognitive trait using measures of cognitive performance from extant species. Phylogenetic methods can also be used to guide the selection of species comparisons that offer the strongest tests of a priori predictions of cognitive evolutionary hypotheses (i.e., phylogenetic targeting). Here, we explain how an integration of comparative psychology and evolutionary biology will answer a host of questions regarding the phylogenetic distribution and history of cognitive traits, as well as the evolutionary processes that drove their evolution.

Translating Basic Behavioral and Social Science Research to Clinical Application: The EVOLVE Mixed Methods Approach

Science.gov (United States)

Peterson, Janey C.; Czajkowski, Susan; Charlson, Mary E.; Link, Alissa R.; Wells, Martin T.; Isen, Alice M.; Mancuso, Carol A.; Allegrante, John P.; Boutin-Foster, Carla; Ogedegbe, Gbenga; Jobe, Jared B.

2013-01-01

Objective: To describe a mixed-methods approach to develop and test a basic behavioral science-informed intervention to motivate behavior change in 3 high-risk clinical populations. Our theoretically derived intervention comprised a combination of positive affect and self-affirmation (PA/SA), which we applied to 3 clinical chronic disease…

Metallurgical test work to support development of the Kintyre Project

International Nuclear Information System (INIS)

Maley, M.; Ring, R.; Paulsen, E.; Maxton, D.

2014-01-01

The Kintyre uranium deposit is located in the Pilbara region of Western Australia and is jointly owned by Cameco and Mitsubishi. The current indicated resource estimate is approximately 55 million pounds of U 3 O 8 equivalent [~21,000 t U] at an average grade of 0.58% [0.49% U]. Due to the high levels of carbonate minerals in the deposit, alkaline leaching was strongly considered as an option to the usually preferred acid route. Following a detailed assessment, the acid option was chosen, with the preferred flowsheet involving an acid leach, followed by solvent extraction and precipitation. As part of the Kintyre metallurgical investigations, ANSTO Minerals performed an extensive work program, examining numerous aspects of the proposed flowsheet. This included a leach optimisation program, followed by a study determining the effects of sample variability in leaching. Settling, filtration and rheology work on slurries and tailings was performed, as well as testwork to determine the effect of neutralisation conditions on metal precipitation and radionuclide deportment. In addition, an extensive laboratory and solvent extraction mixer-settler mini-pilot plan campaign was performed to compare the performance of conventional ammonia/ammonium sulphate strip and the non-conventional strong acid strip (400 g/L H 2 SO 4 ) using leach liquor generated from Kintyre ore. The pilot plant involved two campaigns of three days continuous operation using each stripping system, with >99.5% uranium recovery achieved in each campaign. This paper will present an overview of the key results from the Kintyre leaching and neutralisation testwork undertaken at ANSTO Minerals, and will also outline the performance of the solvent extraction mini pilot plant. (author)

Theoretical and experimental research on the use of expert systems (ES in assessing risks of failure in metallurgical companies

Directory of Open Access Journals (Sweden)

E. Iancu

2013-04-01

Full Text Available The systems’ engineering has reached an explosive development of intelligent systems technology which solves complex problems based on human expertise accumulated in the past and following the processes of learning and reasoning very similar to those of the biological brain. In this article, the concept of the proposed expert system is the result of interdisciplinary researches (computer science, management, accounting and business administration, etc., which are designed to provide a tool for top management work force of a listed metallurgical company. The inference machine will provide in the end score functions for Altman, Conan Holder model and rating which eventually can be combined into a single model that will forecast the company’s evolution in coming years.

Laplacian Estrada and normalized Laplacian Estrada indices of evolving graphs.

Directory of Open Access Journals (Sweden)

Yilun Shang

Full Text Available Large-scale time-evolving networks have been generated by many natural and technological applications, posing challenges for computation and modeling. Thus, it is of theoretical and practical significance to probe mathematical tools tailored for evolving networks. In this paper, on top of the dynamic Estrada index, we study the dynamic Laplacian Estrada index and the dynamic normalized Laplacian Estrada index of evolving graphs. Using linear algebra techniques, we established general upper and lower bounds for these graph-spectrum-based invariants through a couple of intuitive graph-theoretic measures, including the number of vertices or edges. Synthetic random evolving small-world networks are employed to show the relevance of the proposed dynamic Estrada indices. It is found that neither the static snapshot graphs nor the aggregated graph can approximate the evolving graph itself, indicating the fundamental difference between the static and dynamic Estrada indices.

Metallurgical aspects of welding. Ferrous and nonferrous materials. 4. new rev. ed.

International Nuclear Information System (INIS)

Schulze, Guenter

2010-01-01

This is the fourth edition of the standard work on welding metallurgy. The various problems of ferrous and nonferrous materials in the welding process are presented in great detail. In order to prevent corrosion of welded constructions, metallurgical properties and problems of all important technical materials are discussed, i.e. alloyed and unalloyed steels, cast iron materials, and the most relevant nonferrous materials. At the end of each chapter, the interested reader will find exercises for self-studies. Some of these can be solved using the material presented in the book while others are intended for deepening and further training. Easy examples (with solutions) are found all over the book; they are helpful because they provide information on underlying mechanisms and interdependences that are not obvious at first glance. The information was adapted to new EURO standards and international standards (up to March 2009) as far as these are relevant to Germany. New information is provided, e.g., on new steel standards (constructional steels according to DIN EN 10025), heat-treatable steels according to DIN EN 10025-6 and DIN EN 10083, high-alloy steels according to DIN EN 10088, and filler materials for steel welding according to DIN EN ISO 2560. The systematics of the ''law of cohabitation'' was applied to welding engineering for the first time here. (orig.) [de

Designing, Modeling and Evaluating Influence Strategiesfor Behavior Change Support Systems

NARCIS (Netherlands)

Öörni, Anssi; Kelders, Saskia Marion; van Gemert-Pijnen, Julia E.W.C.; Oinas-Kukkonen, Harri

2014-01-01

Behavior change support systems (BCSS) research is an evolving area. While the systems have been demonstrated to work to the effect, there is still a lot of work to be done to better understand the influence mechanisms of behavior change, and work out their influence on the systems architecture. The

Human female orgasm as evolved signal: a test of two hypotheses.

Science.gov (United States)

Ellsworth, Ryan M; Bailey, Drew H

2013-11-01

We present the results of a study designed to empirically test predictions derived from two hypotheses regarding human female orgasm behavior as an evolved communicative trait or signal. One hypothesis tested was the female fidelity hypothesis, which posits that human female orgasm signals a woman's sexual satisfaction and therefore her likelihood of future fidelity to a partner. The other was sire choice hypothesis, which posits that women's orgasm behavior signals increased chances of fertilization. To test the two hypotheses of human female orgasm, we administered a questionnaire to 138 females and 121 males who reported that they were currently in a romantic relationship. Key predictions of the female fidelity hypothesis were not supported. In particular, orgasm was not associated with female sexual fidelity nor was orgasm associated with male perceptions of partner sexual fidelity. However, faked orgasm was associated with female sexual infidelity and lower male relationship satisfaction. Overall, results were in greater support of the sire choice signaling hypothesis than the female fidelity hypothesis. Results also suggest that male satisfaction with, investment in, and sexual fidelity to a mate are benefits that favored the selection of orgasmic signaling in ancestral females.

Metallurgical and reactor physics aspects of using low enrichment fuel in Safari-I

International Nuclear Information System (INIS)

1978-09-01

The feasibility of using lower than 93% enriched fuel in the SAFARI-I research and materials testing reactor is reviewed. Metallurgical experiments show that, using standard U-Al alloy technology and keeping the 235 U loading per element constant without altering the fuel plate thickness, a maximum of 35 weight percent of uranium in the meat can be achieved. This corresponds to using a minimum enrichment of 40% 235 U in order to retain the same mass of 235 U in the core. Even then a loss of approximately 3,3% in reactivity is calculated, which is more than the 2,8% sup(deltak)/k which is normally allowed for burnup. Using current U-Al alloy fuel technology, and an enrichment of approximately 45% 235 U, no changes in core configuration or coolant requirements will be necessary. The use of 20% enriched uranium will require the development of a new fuel design and technology if drastic redesign and modification of the reactor and coolant circuits is to be avoided. Without such new technology, the redesign and modification of the reactor will cost upwards of 3 million dollars and take up to 5 years to complete, requiring a complete shutdown of the reactor for approximately 2 years

Evaluation of Metallurgical Quality of Master Heat IN-713C Nickel Alloy Ingots

Directory of Open Access Journals (Sweden)

Binczyk F.

2012-12-01

Full Text Available The paper presents the results of evaluation of the metallurgical quality of master heat ingots and of the identification of non-metallic inclusions (oxides of Al., Zr, Hf, Cr, etc., which have been found in the shrinkage cavities formed in these ingots. The inclusions penetrate into the liquid alloy, and on pouring of mould are transferred to the casting, especially when the filtering system is not sufficiently effective. The specific nature of the melting process of nickel and cobalt alloys, carried out in vacuum induction furnaces, excludes the possibility of alloy refining and slag removal from the melt surface. Therefore, to improve the quality of castings (parts of aircraft engines, it is so important to evaluate the quality of ingots before charging them into the crucible of an induction furnace. It has been proved that one of the methods for rapid quality evaluation is an ATD analysis of the sample solidification process, where samples are taken from different areas of the master heat ingot. The evaluation is based on a set of parameters plotted on the graph of the dT/dt derivative curve during the last stage of the solidification process in a range from TEut to Tsol.

Evaluation of Metallurgical Quality of Master Heat IN-713C Nickel Alloy Ingots

Directory of Open Access Journals (Sweden)

F. Binczyk

2012-12-01

Full Text Available The paper presents the results of evaluation of the metallurgical quality of master heat ingots and of the identification of non-metallic inclusions (oxides of Al., Zr, Hf, Cr, etc., which have been found in the shrinkage cavities formed in these ingots. The inclusions penetrate into the liquid alloy, and on pouring of mould are transferred to the casting, especially when the filtering system is not sufficiently effective. The specific nature of the melting process of nickel and cobalt alloys, carried out in vacuum induction furnaces,excludes the possibility of alloy refining and slag removal from the melt surface. Therefore, to improve the quality of castings (parts of aircraft engines, it is so important to evaluate the quality of ingots before charging them into the crucible of an induction furnace. It has been proved that one of the methods for rapid quality evaluation is an ATD analysis of the sample solidification process, where samples are taken from different areas of the master heat ingot. The evaluation is based on a set of parameters plotted on the graph of the dT/dt derivative curve during the last stage of the solidification process in a range from TEut to Tsol.

Pyrolysis of chromium rich tanning industrial wastes and utilization of carbonized wastes in metallurgical process.

Science.gov (United States)

Tôrres Filho, Artur; Lange, Liséte Celina; de Melo, Gilberto Caldeira Bandeira; Praes, Gustavo Eduardo

2016-02-01

Pyrolysis is the thermal degradation of organic material in oxygen-free or very lean oxygen atmosphere. This study evaluates the use of pyrolysis for conversion of leather wastes from chromium tanning processes into Carbonized Leather Residues (CLR), and the utilization of CLR in metallurgical processes through the production of iron ore pellets. CLR was used to replace mineral coal in proportions of 10% and 25% on fixed carbon basis content in the mixtures for pellets preparation. Experimental conversions were performed on a pilot scale pyrolysis plant and a pelletizing reactor of the "pot grate" type. The results demonstrated the technical feasibility of using the charcoal product from animal origin as an energy source, with recovery of up to 76.47% of chromium contained in CLR in the final produced of iron ore pellets. Pellets with 25% replacement of fixed carbon in the coal showed an enhanced compressive strength, with an average value of 344kgfpellet(-1), compared to 300kgfpellet(-1) for standard produced pellets. Copyright © 2015. Published by Elsevier Ltd.

The History of Behavioral Treatments in Autism: From the Punitive to the Positive

Science.gov (United States)

Suppo, Jennifer L.

2017-01-01

The behavioral treatments for persons diagnosed with autism have evolved from those that included punitive components to those that are now based upon principles of positive behavior supports. The proceeding document provides an historical overview of relevant behavioral approaches, including the type of approach and the quality of involvement and…

Asymptomatic strut fracture in DeBakey-Surgitool aortic valves: incidence, management, and metallurgic aspects.

Science.gov (United States)

Von Der Emde J, J; Eberlein, U; Breme J, J

1990-01-01

From August 1971 through November 1972, we implanted 62 Model 2 DeBakey-Surgitool aortic valve prostheses in 62 patients, 4 of whom later had clinically asymptomatic strut fractures. In 1 case, the patient died suddenly, and autopsy revealed detachment of the ball-cage; in each of the other 3 cases, fractures of 2 struts close to the base of the prosthesis were diagnosed fluoroscopically, and the patients underwent successful reoperation. The interval between implantation and reoperation ranged from 11 months to 16 years, 9 months. In 1 patient, retrospective study of chest radiographs revealed that the fracture had been present for 2(1/2) years. Larger valves (>/= A6) were affected significantly more often than smaller ones. We performed metallurgic analysis of 1 prosthesis: results revealed strut wear from fatigue cracking and secondary abrasion. Strut fracture was also promoted by suspension of the cage at right angles to the prosthetic ring and by use of a pyrolytic carbon ball in a titanium cage (i.e., an occluder harder than its holder). Patients with DeBakey-Surgitool aortic valve prostheses should undergo annual radiologic examinations to enable early detection of strut fractures. Prophylactic valve replacement is not indicated.

Combined geophysical investigation for the detection of ancient metallurgical installations near Keratea City, Greece

Science.gov (United States)

Apostolopoulos, George V.

2014-05-01

Archaeological excavation in an area of Lavrio (mining area from ancient times) has revealed ancient metallurgical installations which offer valuable information on this activity at those times. Within this context, a combined geophysical investigation was carried out in a place near Keratea City to find out whether there are additional installations apart from those that have already been revealed in the immediate area. More importantly, the objective was to locate the ancient tanks which provided water to the installations. Archaeological and geological information have helped in the design of the survey. EMI method measuring apparent conductivity was used to cover the whole area of investigation. Conductivity maps in various investigation depths have positioned the tanks and stacked first derivative maps in two directions (the two directions of the revealed walls) show covered walls. The EMI survey has indicated the position of three (3) ERT profiles made with the dipole-dipole array, which presented the ancient tanks with great detail in depth. GPR profiles for the detection of walls were noisy with the coarse material surface layer but the interrelation with ERT and EMI results confirmed the detected features.

Effect of metallurgical factors on the bulk magnetic properties of non-oriented electrical steels

Energy Technology Data Exchange (ETDEWEB)

Ghosh, Pampa, E-mail: pampaghosh@gmail.com [Department of Mining and Materials Engineering, McGill University, 3610 University Street, Montreal, Que., Canada H3A 0C5 (Canada); Chromik, Richard R., E-mail: richard.chromik@mcgill.ca [Department of Mining and Materials Engineering, McGill University, 3610 University Street, Montreal, Que., Canada H3A 0C5 (Canada); Knight, Andrew M. [Department of Electrical and Computer Engineering, University of Alberta, Edmonton, Alta., Canada T6G 2V4 (Canada); Wakade, Shekhar G. [GM Powertrain, General Motors Company, 823 Joslyn Avenue, Building B, 4AJ35, Pontiac, MI 48340-2920 (United States)

2014-04-01

Non-oriented electrical steel (NOES) is one of the most common material used in electrical motors. Core loss and permeability are the most important properties that the motor manufacturers look for. Both these properties are structure sensitive and depend on several metallurgical factors; such as chemistry, grain size, crystallographic texture, cleanliness and stress states in non-oriented electrical steels. It has been observed in this course of the study that the grain size and Si content of NOES are the primary controlling factors to core loss, especially at higher frequencies. On the contrary, crystallographic texture plays an important role at lower frequencies. At higher frequency, core loss increases with increasing grain size and decreasing Si content of the steels. Small difference in grain size (∼50 μm) at lower frequency range has little influence on the magnetic properties but has significant adverse effect as frequency reaches high enough. - Highlights: • Magnetic properties of a set of electrical steels were measured. • Crystallographic texture, chemistry and grain size were studied for their effects on core loss and permeability. • Structure–magnetic property relationships were identified for the electrical steels.

Evolvable mathematical models: A new artificial Intelligence paradigm

Science.gov (United States)

Grouchy, Paul

We develop a novel Artificial Intelligence paradigm to generate autonomously artificial agents as mathematical models of behaviour. Agent/environment inputs are mapped to agent outputs via equation trees which are evolved in a manner similar to Symbolic Regression in Genetic Programming. Equations are comprised of only the four basic mathematical operators, addition, subtraction, multiplication and division, as well as input and output variables and constants. From these operations, equations can be constructed that approximate any analytic function. These Evolvable Mathematical Models (EMMs) are tested and compared to their Artificial Neural Network (ANN) counterparts on two benchmarking tasks: the double-pole balancing without velocity information benchmark and the challenging discrete Double-T Maze experiments with homing. The results from these experiments show that EMMs are capable of solving tasks typically solved by ANNs, and that they have the ability to produce agents that demonstrate learning behaviours. To further explore the capabilities of EMMs, as well as to investigate the evolutionary origins of communication, we develop NoiseWorld, an Artificial Life simulation in which interagent communication emerges and evolves from initially noncommunicating EMM-based agents. Agents develop the capability to transmit their x and y position information over a one-dimensional channel via a complex, dialogue-based communication scheme. These evolved communication schemes are analyzed and their evolutionary trajectories examined, yielding significant insight into the emergence and subsequent evolution of cooperative communication. Evolved agents from NoiseWorld are successfully transferred onto physical robots, demonstrating the transferability of EMM-based AIs from simulation into physical reality.

Simulating the Evolving Behavior of Secondary Slow Slip Fronts

Science.gov (United States)

Peng, Y.; Rubin, A. M.

2017-12-01

High-resolution tremor catalogs of slow slip events reveal secondary slow slip fronts behind the main front that repetitively occupy the same source area during a single episode. These repetitive fronts are most often observed in regions with high tremor density. Their recurrence intervals gradually increase from being too short to be tidally modulated (tens of minutes) to being close to tidal periods (about 12 or 24 hours). This could be explained by a decreasing loading rate from creep in the surrounding regions (with few or no observable tremor events) as the main front passes by. As the recurrence intervals of the fronts increase, eventually they lock in on the tidal periods. We attempt to simulate this numerically using a rate-and-state friction law that transitions from velocity-weakening at low slip speeds to velocity strengthening at high slip speeds. Many small circular patches with a cutoff velocity an order of magnitude higher than that of the background are randomly placed on the fault, in order to simulate the average properties of the high-density tremor zone. Preliminary results show that given reasonable parameters, this model produces similar propagation speeds of the forward-migrating main front inside and outside the high-density tremor zone, consistent with observations. We will explore the behavior of the secondary fronts that arise in this model, in relation to the local density of the small tremor-analog patches, the overall geometry of the tremor zone and the tides.

PCBA demand forecasting using an evolving Takagi-Sugeno system

NARCIS (Netherlands)

van Rooijen, M.; Almeida, R.J.; Kaymak, U.

2016-01-01

This paper investigates the use of using an evolving fuzzy system for printed circuit board (PCBA) demand forecasting. The algorithm is based on the evolving Takagi-Sugeno (eTS) fuzzy system, which has the ability to incorporate new patterns by changing its internal structure in an on-line fashion.

CMIP6 Data Citation of Evolving Data

Directory of Open Access Journals (Sweden)

Martina Stockhause

2017-06-01

Full Text Available Data citations have become widely accepted. Technical infrastructures as well as principles and recommendations for data citation are in place but best practices or guidelines for their implementation are not yet available. On the other hand, the scientific climate community requests early citations on evolving data for credit, e.g. for CMIP6 (Coupled Model Intercomparison Project Phase 6. The data citation concept for CMIP6 is presented. The main challenges lie in limited resources, a strict project timeline and the dependency on changes of the data dissemination infrastructure ESGF (Earth System Grid Federation to meet the data citation requirements. Therefore a pragmatic, flexible and extendible approach for the CMIP6 data citation service was developed, consisting of a citation for the full evolving data superset and a data cart approach for citing the concrete used data subset. This two citation approach can be implemented according to the RDA recommendations for evolving data. Because of resource constraints and missing project policies, the implementation of the second part of the citation concept is postponed to CMIP7.

Marshal: Maintaining Evolving Models, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — SIFT proposes to design and develop the Marshal system, a mixed-initiative tool for maintaining task models over the course of evolving missions. Marshal-enabled...

Do host species evolve a specific response to slave-making ants?

Directory of Open Access Journals (Sweden)

Delattre Olivier

2012-12-01

Full Text Available Abstract Background Social parasitism is an important selective pressure for social insect species. It is particularly the case for the hosts of dulotic (so called slave-making ants, which pillage the brood of host colonies to increase the worker force of their own colony. Such raids can have an important impact on the fitness of the host nest. An arms race which can lead to geographic variation in host defenses is thus expected between hosts and parasites. In this study we tested whether the presence of a social parasite (the dulotic ant Myrmoxenus ravouxi within an ant community correlated with a specific behavioral defense strategy of local host or non-host populations of Temnothorax ants. Social recognition often leads to more or less pronounced agonistic interactions between non-nestmates ants. Here, we monitored agonistic behaviors to assess whether ants discriminate social parasites from other ants. It is now well-known that ants essentially rely on cuticular hydrocarbons to discriminate nestmates from aliens. If host species have evolved a specific recognition mechanism for their parasite, we hypothesize that the differences in behavioral responses would not be fully explained simply by quantitative dissimilarity in cuticular hydrocarbon profiles, but should also involve a qualitative response due to the detection of particular compounds. We scaled the behavioral results according to the quantitative chemical distance between host and parasite colonies to test this hypothesis. Results Cuticular hydrocarbon profiles were distinct between species, but host species did not show a clearly higher aggression rate towards the parasite than toward non-parasite intruders, unless the degree of response was scaled by the chemical distance between intruders and recipient colonies. By doing so, we show that workers of the host and of a non-host species in the parasitized site displayed more agonistic behaviors (bites and ejections towards parasite

Orthogonally Evolved AI to Improve Difficulty Adjustment in Video Games

DEFF Research Database (Denmark)

Hintze, Arend; Olson, Randal; Lehman, Joel Anthony

2016-01-01

Computer games are most engaging when their difficulty is well matched to the player's ability, thereby providing an experience in which the player is neither overwhelmed nor bored. In games where the player interacts with computer-controlled opponents, the difficulty of the game can be adjusted...... not only by changing the distribution of opponents or game resources, but also through modifying the skill of the opponents. Applying evolutionary algorithms to evolve the artificial intelligence that controls opponent agents is one established method for adjusting opponent difficulty. Less-evolved agents...... (i.e. agents subject to fewer generations of evolution) make for easier opponents, while highly-evolved agents are more challenging to overcome. In this publication we test a new approach for difficulty adjustment in games: orthogonally evolved AI, where the player receives support from collaborating...

Concentration of gold, sulphide minerals, and uranium oxide minerals by flotation from ores and metallurgical plant products

International Nuclear Information System (INIS)

Weston, D.

1976-01-01

A process is described for the concentration by flotation of gold, gold bearing minerals and uranium oxide minerals from ores and metallurgical plant products. A pulp of a ground ore is agitation conditioned in at least two agitation conditioning stages wherein in at least one stage the pH of the pulp is lowered with an acid agent to within the pH range of about 1.5 to 5.0, and wherein in at least one additional agitation conditioning stage the pH of the pulp is raised to within the pH range of about 6.0 to 11.0 and wherein in at least the last stage prior to flotation at least one collector selected from the group of sulfhydryl anionic collectors is present. Subsequently, the at least two stage agitation conditioned pulp is subjected to flotation to produce a flotation concentrate enriched in at least one of the mineral values from the group consisting of gold, gold bearing minerals and uranium minerals

Powder metallurgical processing of functionally graded p-Pb1-x Sn x Te materials for thermoelectric applications

International Nuclear Information System (INIS)

Gelbstein, Y.; Dashevsky, Z.; Dariel, M.P.

2007-01-01

Lead tin telluride-based compounds are p-type materials for thermoelectric applications, in the 50-600 deg. C temperature range. The electronic transport properties of PbTe and Pb 1- x Sn x Te materials are strongly dependent on the processing approach. Powder metallurgy is a suitable approach for the preparation of Functionally graded materials (FGMs) but its effects on the electronic properties have to be carefully checked. Powder metallurgical processing may introduce atomic defects and local strains into the material and, thereby, alter the carrier concentration. Such material may be in non-equilibrium conditions at the operating temperature with unstable thermoelectric properties. This effect can be reduced and eliminated by appropriate annealing procedures. In FGMs, annealing up to the stabilization of the thermoelectric properties is mandatory for achieving the desired carrier concentration profile along the sample. The design procedures of the FGMs, as well as the annealing effects on cold compacted and sintered Pb 1- x Sn x Te samples are described in details

Overcoming Deception in Evolution of Cognitive Behaviors

DEFF Research Database (Denmark)

Lehman, Joel; Miikkulainen, Risto

2014-01-01

When scaling neuroevolution to complex behaviors, cognitive capabilities such as learning, communication, and memory become increasingly important. However, successfully evolving such cognitive abilities remains difficult. This paper argues that a main cause for such difficulty is deception, i.......e. evolution converges to a behavior unrelated to the desired solution. More specifically, cognitive behaviors often require accumulating neural structure that provides no immediate fitness benefit, and evolution often thus converges to non-cognitive solutions. To investigate this hypothesis, a common...... evolutionary robotics T-Maze domain is adapted in three separate ways to require agents to communicate, remember, and learn. Indicative of deception, evolution driven by objective-based fitness often converges upon simple non- cognitive behaviors. In contrast, evolution driven to explore novel behaviors, i...

Computational Genetic Regulatory Networks Evolvable, Self-organizing Systems

CERN Document Server

Knabe, Johannes F

2013-01-01

Genetic Regulatory Networks (GRNs) in biological organisms are primary engines for cells to enact their engagements with environments, via incessant, continually active coupling. In differentiated multicellular organisms, tremendous complexity has arisen in the course of evolution of life on earth. Engineering and science have so far achieved no working system that can compare with this complexity, depth and scope of organization. Abstracting the dynamics of genetic regulatory control to a computational framework in which artificial GRNs in artificial simulated cells differentiate while connected in a changing topology, it is possible to apply Darwinian evolution in silico to study the capacity of such developmental/differentiated GRNs to evolve. In this volume an evolutionary GRN paradigm is investigated for its evolvability and robustness in models of biological clocks, in simple differentiated multicellularity, and in evolving artificial developing 'organisms' which grow and express an ontogeny starting fr...

Adaptive inferential sensors based on evolving fuzzy models.

Science.gov (United States)

Angelov, Plamen; Kordon, Arthur

2010-04-01

A new technique to the design and use of inferential sensors in the process industry is proposed in this paper, which is based on the recently introduced concept of evolving fuzzy models (EFMs). They address the challenge that the modern process industry faces today, namely, to develop such adaptive and self-calibrating online inferential sensors that reduce the maintenance costs while keeping the high precision and interpretability/transparency. The proposed new methodology makes possible inferential sensors to recalibrate automatically, which reduces significantly the life-cycle efforts for their maintenance. This is achieved by the adaptive and flexible open-structure EFM used. The novelty of this paper lies in the following: (1) the overall concept of inferential sensors with evolving and self-developing structure from the data streams; (2) the new methodology for online automatic selection of input variables that are most relevant for the prediction; (3) the technique to detect automatically a shift in the data pattern using the age of the clusters (and fuzzy rules); (4) the online standardization technique used by the learning procedure of the evolving model; and (5) the application of this innovative approach to several real-life industrial processes from the chemical industry (evolving inferential sensors, namely, eSensors, were used for predicting the chemical properties of different products in The Dow Chemical Company, Freeport, TX). It should be noted, however, that the methodology and conclusions of this paper are valid for the broader area of chemical and process industries in general. The results demonstrate that well-interpretable and with-simple-structure inferential sensors can automatically be designed from the data stream in real time, which predict various process variables of interest. The proposed approach can be used as a basis for the development of a new generation of adaptive and evolving inferential sensors that can address the

An Evolving Asymmetric Game for Modeling Interdictor-Smuggler Problems

Science.gov (United States)

2016-06-01

ASYMMETRIC GAME FOR MODELING INTERDICTOR-SMUGGLER PROBLEMS by Richard J. Allain June 2016 Thesis Advisor: David L. Alderson Second Reader: W...DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE AN EVOLVING ASYMMETRIC GAME FOR MODELING INTERDICTOR- SMUGGLER PROBLEMS 5. FUNDING NUMBERS 6...NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release; distribution is unlimited AN EVOLVING

Characterization of metallurgical and mechanical properties on the multi-pass welding of Inconel 625 and AISI 316L

Energy Technology Data Exchange (ETDEWEB)

Kumar, K. Gokul; Ramkumar, K. Devendranath; Arivazhagan, N. [VIT University, Vellore (India)

2015-03-15

This article investigated the weldability, metallurgical and mechanical properties of Inconel 625 and AISI 316L stainless steel weldments obtained by continuous current (CC) and pulsed current (PC) gas tungsten arc welding (GTAW) processes employing ERNiCr-3 and ER2209 fillers. Microstructure studies showed the migrated grain boundaries at the weld zone of ERNiCr-3 weldments and multidirectional grain growth for ER2209 weldments. It was inferred from the tension tests that the fracture occurred at the parent metal of AISI 316L in all the cases. Charpy V-notch impact tests accentuated that the CCGTA weldments employing ERNiCr-3 filler offered better impact toughness of 77 J at room temperature. Further a detailed study has been carried out to analyze the structure - property relationships of these weldments using the combined techniques of scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis.

Symbiotic Composition and Evolvability

OpenAIRE

Watson, Richard A.; Pollack, Jordan B.

2001-01-01

Several of the Major Transitions in natural evolution, such as the symbiogenic origin of eukaryotes from prokaryotes, share the feature that existing entities became the components of composite entities at a higher level of organisation. This composition of pre-adapted extant entities into a new whole is a fundamentally different source of variation from the gradual accumulation of small random variations, and it has some interesting consequences for issues of evolvability. In this paper we p...

Linking brain, mind and behavior.

Science.gov (United States)

Makeig, Scott; Gramann, Klaus; Jung, Tzyy-Ping; Sejnowski, Terrence J; Poizner, Howard

2009-08-01

Cortical brain areas and dynamics evolved to organize motor behavior in our three-dimensional environment also support more general human cognitive processes. Yet traditional brain imaging paradigms typically allow and record only minimal participant behavior, then reduce the recorded data to single map features of averaged responses. To more fully investigate the complex links between distributed brain dynamics and motivated natural behavior, we propose the development of wearable mobile brain/body imaging (MoBI) systems that continuously capture the wearer's high-density electrical brain and muscle signals, three-dimensional body movements, audiovisual scene and point of regard, plus new data-driven analysis methods to model their interrelationships. The new imaging modality should allow new insights into how spatially distributed brain dynamics support natural human cognition and agency.

Metallurgical characterization of brass objects from the Akko 1 shipwreck, Israel

International Nuclear Information System (INIS)

Ashkenazi, D.; Cvikel, D.; Stern, A.; Klein, S.; Kahanov, Y.

2014-01-01

The Akko 1 shipwreck was a small Egyptian armed vessel or auxiliary naval brig built in the eastern Mediterranean at the beginning of the 19th century. During the underwater excavations, about 230 brass hook-and-eye closures were found, mainly in the bow area. In addition, 158 brass cases were found, mainly between midships and the aft extremity of the shipwreck. Metallurgical non-destructive and destructive characterizations of selected items were performed, including radiographic testing, XRF, lead isotope analysis, optical microscopy, SEM–EDS and microhardness tests. The hook-and-eye closures and the cases were both found to be made of binary copper–zinc alloy (about 30 wt.% zinc). While the brass cases were made from rolled sheets, hand-made using simple tools, and joined by tin–lead soldering material, the brass hook-and-eye closures were hand-made from drawn brass wire, and manufactured from commercial drawn brass bars by a cold-working process. The lead isotope analyses suggest different provenances of the raw materials used for making the brass objects, thus the different origins of the ores may hint that the brass wire and sheet were imported to the workshops in which the objects were manufactured. - Highlights: • Brass cases and hook-and-eye closures were retrieved from the Akko 1 shipwreck. • Both types of objects were made of binary copper–zinc alloy (about 30 wt.% zinc). • The cases were hand-made from rolled sheets and joined by tin–lead soldering. • Hook-and-eye closures were made from drawn brass wire manufactured by cold-working. • Lead isotope analyses suggest that the origins of the raw material were diverse

Comparative assessment of metallurgical recovery of metals from electronic waste with special emphasis on bioleaching.

Science.gov (United States)

Priya, Anshu; Hait, Subrata

2017-03-01

Waste electrical and electronic equipment (WEEE) or electronic waste (e-waste) is one of the fastest growing waste streams in the urban environment worldwide. The core component of printed circuit board (PCB) in e-waste contains a complex array of metals in rich quantity, some of which are toxic to the environment and all of which are valuable resources. Therefore, the recycling of e-waste is an important aspect not only from the point of waste treatment but also from the recovery of metals for economic growth. Conventional approaches for recovery of metals from e-waste, viz. pyrometallurgical and hydrometallurgical techniques, are rapid and efficient, but cause secondary pollution and economically unviable. Limitations of the conventional techniques have led to a shift towards biometallurgical technique involving microbiological leaching of metals from e-waste in eco-friendly manner. However, optimization of certain biotic and abiotic factors such as microbial species, pH, temperature, nutrients, and aeration rate affect the bioleaching process and can lead to profitable recovery of metals from e-waste. The present review provides a comprehensive assessment on the metallurgical techniques for recovery of metals from e-waste with special emphasis on bioleaching process and the associated factors.

Effect of friction time on mechanical and metallurgical properties of continuous drive friction welded Ti6Al4V/SUS321 joints

International Nuclear Information System (INIS)

Li, Peng; Li, Jinglong; Salman, Muhammad; Liang, Li; Xiong, Jiangtao; Zhang, Fusheng

2014-01-01

Highlights: • The effect of friction time on the microstructure and joint strength was studied. • The fit of burn-off lengths at different times yields a simple equation. • The longer friction time leads to oversized flash in Ti6Al4V side and overgrown IMCs. • An IMZ with width less than 3 μm is beneficial to make a strong metallurgical bond. • The average strength of 560 MPa is obtained and higher than ever reported results. - Abstract: Dissimilar joint of Ti6Al4V titanium alloy and SUS321 stainless steel was fabricated by continuous drive friction welding. The effect of friction time on the mechanical properties was evaluated by hardness measurement and tensile test, while the interfacial microstructure and fracture morphologies were analyzed by scanning electron microscope, energy dispersive spectroscope and X-ray Diffraction. The results show that the tensile strength increases with friction time under the experimental conditions. And the maximum average strength 560 MPa, which is 90.3% of the SUS321 base metal, is achieved at a friction time of 4 s. For all samples, studied fracture occurred along the joint interface, where intermetallic compounds like FeTi, Fe 2 Ti, Ni 3 (Al, Ti) and Fe 3 Ti 3 O and many other phases were formed among elements from the two base metals. The width of intermetallic compounds zone increases with friction time up to 3 μm, below which it is beneficial to make a strong metallurgical bond. However, the longer friction time leads to oversized flash on the Ti6Al4V side and overgrown intermetallic compounds. Finally the optimized friction time was discussed to be in the range of 2–4 s, under which the sound joint with good reproducibility can be expected

Selective attention and control of action: comparative psychology of an artificial, evolved agent and people.

Science.gov (United States)

Ward, Robert; Ward, Ronnie

2008-10-01

This study examined the selective attention abilities of a simple, artificial, evolved agent and considered implications of the agent's performance for theories of selective attention and action. The agent processed two targets in continuous time, catching one and then the other. This task required many cognitive operations, including prioritizing the first target (T1) over the second (T2); selectively focusing responses on T1, while preventing T2 from interfering with responses; creating a memory for the unselected T2 item, so that it could be efficiently processed later; and reallocating processing towards T2 after catching T1. The evolved agent demonstrated all these abilities. Analysis shows that the agent used reactive inhibition to selectively focus behavior. That is, the more salient T2, the more strongly responses towards T2 were inhibited and the slower the agent was to subsequently reallocate processing towards T2. Reactive inhibition was also suggested in two experiments with people, performing a virtually identical catch task. The presence of reactive inhibition in the simple agent and in people suggests that it is an important mechanism for selective processing.

Modeling lahar behavior and hazards

Science.gov (United States)

Manville, Vernon; Major, Jon J.; Fagents, Sarah A.

2013-01-01

Lahars are highly mobile mixtures of water and sediment of volcanic origin that are capable of traveling tens to > 100 km at speeds exceeding tens of km hr-1. Such flows are among the most serious ground-based hazards at many volcanoes because of their sudden onset, rapid advance rates, long runout distances, high energy, ability to transport large volumes of material, and tendency to flow along existing river channels where populations and infrastructure are commonly concentrated. They can grow in volume and peak discharge through erosion and incorporation of external sediment and/or water, inundate broad areas, and leave deposits many meters thick. Furthermore, lahars can recur for many years to decades after an initial volcanic eruption, as fresh pyroclastic material is eroded and redeposited during rainfall events, resulting in a spatially and temporally evolving hazard. Improving understanding of the behavior of these complex, gravitationally driven, multi-phase flows is key to mitigating the threat to communities at lahar-prone volcanoes. However, their complexity and evolving nature pose significant challenges to developing the models of flow behavior required for delineating their hazards and hazard zones.

Evolving Systems: Adaptive Key Component Control and Inheritance of Passivity and Dissipativity

Science.gov (United States)

Frost, S. A.; Balas, M. J.

2010-01-01

We propose a new framework called Evolving Systems to describe the self-assembly, or autonomous assembly, of actively controlled dynamical subsystems into an Evolved System with a higher purpose. Autonomous assembly of large, complex flexible structures in space is a target application for Evolving Systems. A critical requirement for autonomous assembling structures is that they remain stable during and after assembly. The fundamental topic of inheritance of stability, dissipativity, and passivity in Evolving Systems is the primary focus of this research. In this paper, we develop an adaptive key component controller to restore stability in Nonlinear Evolving Systems that would otherwise fail to inherit the stability traits of their components. We provide sufficient conditions for the use of this novel control method and demonstrate its use on an illustrative example.

Qualitative Functional Decomposition Analysis of Evolved Neuromorphic Flight Controllers

Directory of Open Access Journals (Sweden)

Sanjay K. Boddhu

2012-01-01

Full Text Available In the previous work, it was demonstrated that one can effectively employ CTRNN-EH (a neuromorphic variant of EH method methodology to evolve neuromorphic flight controllers for a flapping wing robot. This paper describes a novel frequency grouping-based analysis technique, developed to qualitatively decompose the evolved controllers into explainable functional control blocks. A summary of the previous work related to evolving flight controllers for two categories of the controller types, called autonomous and nonautonomous controllers, is provided, and the applicability of the newly developed decomposition analysis for both controller categories is demonstrated. Further, the paper concludes with appropriate discussion of ongoing work and implications for possible future work related to employing the CTRNN-EH methodology and the decomposition analysis techniques presented in this paper.

Information Behavior: A Socio-Cognitive Ability

Directory of Open Access Journals (Sweden)

Amanda Spink

2007-04-01

Full Text Available How has human information behavior evolved? Our paper explores this question in the form of notions, models and theories about the relationship between information behavior and human evolution. Alexander's Ecological Dominance and Social Competition/Cooperation (EDSC model currently provides the most comprehensive overview of human traits in the development of a theory of human evolution and sociality. His model provides a basis for explaining the evolution of human socio-cognitive abilities, including ecological dominance, and social competition/cooperation. Our paper examines the human trait of information behavior as a socio-cognitive ability related to ecological dominance, and social competition/cooperation. The paper first outlines what is meant by information behavior from various interdisciplinary perspectives. We propose that information behavior is a socio-cognitive ability that is related to and enables other socio-cognitive abilities such as human ecological dominance, and social competition/cooperation. The paper reviews the current state of evolutionary approaches to information behavior and future directions for this research

Metallurgical study of low-temperature plasma carbon diffusion treatments for stainless steels

International Nuclear Information System (INIS)

Lewis, D.B.; Leyland, A.; Stevenson, P.R.; Cawley, J.; Matthews, A.

1993-01-01

We recently reported a novel low-temperature carbon diffusion technique for surface hardening of stainless steels. The treatment was shown to provide benefits in terms of abrasive wear resistance. There is also evidence to suggest that by performing diffusion treatments at low temperatures (i.e. below 400 C), these benefits can be achieved without compromising corrosion resistance. Here a variety of surface analysis and depth profiling techniques have been used to determine the physical and mechanical properties of carbon-rich layers produced on a range of stainless steel substrate materials. X-ray diffraction (XRD) was employed to determine the crystallographic structure, whilst wavelength dispersive X-ray analysis (WDX) and glow discharge optical spectroscopy (GDOS) gave information on the concentration and distribution of the diffused species within the treated layers. A variety of carbide-based structures was detected, including the expected M 23 C 6 and, more surprisingly, M 3 C. Optical and electron microscopy techniques were used to provide information on layer morphology. The surfaces produced by the low-temperature carbon-diffusion process generally exhibit a distinct diffusion layer of between 1 and 20 μm, depending on the material and the treatment conditions. Austenitic stainless steels appear to give the best response to treatment, however other types of stainless steel can be treated, particularly if the microstructure contains above 5% retained austenite. Here we discuss the changes in mechanical and metallurgical properties provided by this technique and its potential value for treatment of both austenitic and other stainless steel substrate materials. (orig.)

Genetic programming for evolving due-date assignment models in job shop environments.

Science.gov (United States)

Nguyen, Su; Zhang, Mengjie; Johnston, Mark; Tan, Kay Chen

2014-01-01

Due-date assignment plays an important role in scheduling systems and strongly influences the delivery performance of job shops. Because of the stochastic and dynamic nature of job shops, the development of general due-date assignment models (DDAMs) is complicated. In this study, two genetic programming (GP) methods are proposed to evolve DDAMs for job shop environments. The experimental results show that the evolved DDAMs can make more accurate estimates than other existing dynamic DDAMs with promising reusability. In addition, the evolved operation-based DDAMs show better performance than the evolved DDAMs employing aggregate information of jobs and machines.

Views on Evolvability of Embedded Systems

NARCIS (Netherlands)

Laar, P. van de; Punter, T.

2011-01-01

Evolvability, the ability to respond effectively to change, represents a major challenge to today's high-end embedded systems, such as those developed in the medical domain by Philips Healthcare. These systems are typically developed by multi-disciplinary teams, located around the world, and are in

Views on evolvability of embedded systems

NARCIS (Netherlands)

Laar, van de P.J.L.J.; Punter, H.T.

2011-01-01

Evolvability, the ability to respond effectively to change, represents a major challenge to today's high-end embedded systems, such as those developed in the medical domain by Philips Healthcare. These systems are typically developed by multi-disciplinary teams, located around the world, and are in

Ice core based Pb pollution from gasoline in South America in the context of a 2000 year metallurgical history

Science.gov (United States)

Eichler, Anja; Gramlich, Gabriela; Kellerhals, Thomas; Tobler, Leonhard; Schwikowski, Margit

2015-04-01

Lead (Pb) is highly neurotoxic and, in contrast to many other heavy metals including cobalt, copper, and zinc, it has no beneficial effects to humans even at low concentrations. The introduction of leaded gasoline in the 1920s initiated a period of unabated growth in the global emissions of Pb. Prior to the onset of leaded gasoline phase-out in the 1970s, atmospheric Pb levels increased dramatically. Long-term histories of Pb pollution in Eastern and Western Europe, Asia, and North America suggest that emissions from leaded gasoline within the Northern Hemisphere are dominant compared to that from metallurgy and coal combustion during the second half of the 20th century. However, there is no equivalent data for Southern America. Although exploitation of the extensive polymetallic deposits of the Andean Altiplano in South America since pre-colonial times has caused substantial emissions of neurotoxic Pb into the atmosphere, its historical significance compared to recent Pb pollution from leaded gasoline is not yet resolved. Here we present the first comprehensive, high-resolution two millennia Pb emission history for South America, based on ice core records of Pb concentrations, Pb enrichment factors (EFs), and Pb isotope ratios from Illimani glacier in Bolivia. Complementary to local air pollution recorded in lake sediments, ice cores from mid latitude glaciers provide information about more extended source areas. Illimani is the highest mountain of the eastern Bolivian Andes and is located at the northeastern margin of the Bolivian Altiplano. The ice core Pb deposition history revealed enhanced Pb EFs due to metallurgical processing for silver production during periods of the Tiwanaku/Wari culture (AD 450-950), the Inca empires (AD 1450-1532), colonial times (AD 1532-1900), and tin production at the beginning of the 20th century. After the 1960s 208Pb/207Pb ratios decreased significantly, whereas Pb EFs increased by a factor of three compared to the emission level

Risk factors which cause senile cataract evolvement: outline

Directory of Open Access Journals (Sweden)

E.V. Bragin

2018-03-01

Full Text Available Examination of natural ageing processes including those caused by multiple external factors has been attracting re-searchers' attention over the last years. Senile cataract is a multi-factor disease. Expenditure on cataract surgery remain one of the greatest expenses items in public health care. Age is a basic factor which causes senile cataract. Morbidity with cataract doubles each 10 years of life. This outline considers some literature sources which describe research results on influence exerted on cataract evolvement by such risk factors as age, sex, race, smoking, alcohol intake, pancreatic diabetes, intake of certain medications, a number of environmental factors including ultraviolet and ionizing radiation. mane of these factors are shown to increase or reduce senile cataract risk; there are conflicting data on certain factors. The outline also contains quantitative characteristics of cataract risks which are given via odds relation and evolve due to age parameters impacts, alcohol intake, ionizing radiation, etc. The authors also state that still there is no answer to the question whether dose-effect relationship for cataract evolvement is a threshold or non-threshold.

Occurrence and characterisation of the hydrogen-evolving enzyme in Frankia sp.

Energy Technology Data Exchange (ETDEWEB)

Mohapatra, A.; Leul, M.; Sellstedt, A. [Umeaa Plant Science Centre, Department of Plant Physiology, Umeaa University, S-901 87 Umeaa (Sweden); Sandstroem, G. [Karolinska Institutet, Department of Laboratory Medicine, Division of Clinical Bacteriology, Karelinska University Hospital, Huddinge, S-141 86 Stockholm (Sweden)

2006-09-15

An increase in hydrogen evolution from the hydrogen-evolving enzyme in the actinomycete Frankia was recorded in the presence of nickel. Immunogold localisation analysis of the intracellular distribution of hydrogenase proteins indicated that they were evenly distributed in the membranes and cytosol of both hyphae and vesicles. In addition, molecular characterisation of the hydrogen-evolving enzyme at the proteomic level, using two-dimensional gel electrophoresis combined with mass spectrometry, confirmed that the Frankia hydrogen-evolving enzyme is similar to the cyanobacterial bidirectional hydrogenase of Anabena siamensis. (author)

Evolution of networks for body plan patterning; interplay of modularity, robustness and evolvability.

Directory of Open Access Journals (Sweden)

Kirsten H Ten Tusscher

2011-10-01

Full Text Available A major goal of evolutionary developmental biology (evo-devo is to understand how multicellular body plans of increasing complexity have evolved, and how the corresponding developmental programs are genetically encoded. It has been repeatedly argued that key to the evolution of increased body plan complexity is the modularity of the underlying developmental gene regulatory networks (GRNs. This modularity is considered essential for network robustness and evolvability. In our opinion, these ideas, appealing as they may sound, have not been sufficiently tested. Here we use computer simulations to study the evolution of GRNs' underlying body plan patterning. We select for body plan segmentation and differentiation, as these are considered to be major innovations in metazoan evolution. To allow modular networks to evolve, we independently select for segmentation and differentiation. We study both the occurrence and relation of robustness, evolvability and modularity of evolved networks. Interestingly, we observed two distinct evolutionary strategies to evolve a segmented, differentiated body plan. In the first strategy, first segments and then differentiation domains evolve (SF strategy. In the second scenario segments and domains evolve simultaneously (SS strategy. We demonstrate that under indirect selection for robustness the SF strategy becomes dominant. In addition, as a byproduct of this larger robustness, the SF strategy is also more evolvable. Finally, using a combined functional and architectural approach, we determine network modularity. We find that while SS networks generate segments and domains in an integrated manner, SF networks use largely independent modules to produce segments and domains. Surprisingly, we find that widely used, purely architectural methods for determining network modularity completely fail to establish this higher modularity of SF networks. Finally, we observe that, as a free side effect of evolving segmentation

A two-step leaching method designed based on chemical fraction distribution of the heavy metals for selective leaching of Cd, Zn, Cu, and Pb from metallurgical sludge.

Science.gov (United States)

Wang, Fen; Yu, Junxia; Xiong, Wanli; Xu, Yuanlai; Chi, Ru-An

2018-01-01

For selective leaching and highly effective recovery of heavy metals from a metallurgical sludge, a two-step leaching method was designed based on the distribution analysis of the chemical fractions of the loaded heavy metal. Hydrochloric acid (HCl) was used as a leaching agent in the first step to leach the relatively labile heavy metals and then ethylenediamine tetraacetic acid (EDTA) was applied to leach the residual metals according to their different fractional distribution. Using the two-step leaching method, 82.89% of Cd, 55.73% of Zn, 10.85% of Cu, and 0.25% of Pb were leached in the first step by 0.7 M HCl at a contact time of 240 min, and the leaching efficiencies for Cd, Zn, Cu, and Pb were elevated up to 99.76, 91.41, 71.85, and 94.06%, by subsequent treatment with 0.2 M EDTA at 480 min, respectively. Furthermore, HCl leaching induced fractional redistribution, which might increase the mobility of the remaining metals and then facilitate the following metal removal by EDTA. The facilitation was further confirmed by the comparison to the one-step leaching method with single HCl or single EDTA, respectively. These results suggested that the designed two-step leaching method by HCl and EDTA could be used for selective leaching and effective recovery of heavy metals from the metallurgical sludge or heavy metal-contaminated solid media.

EVOLVING AN EMPIRICAL METHODOLOGY DOR DETERMINING ...

African Journals Online (AJOL)

The uniqueness of this approach, is that it can be applied to any forest or dynamic feature on the earth, and can enjoy universal application as well. KEY WORDS: Evolving empirical methodology, innovative mathematical model, appropriate interval, remote sensing, forest environment planning and management. Global Jnl ...

EVOLVE : a Bridge between Probability, Set Oriented Numerics, and Evolutionary Computation II

CERN Document Server

Coello, Carlos; Tantar, Alexandru-Adrian; Tantar, Emilia; Bouvry, Pascal; Moral, Pierre; Legrand, Pierrick; EVOLVE 2012

2013-01-01

This book comprises a selection of papers from the EVOLVE 2012 held in Mexico City, Mexico. The aim of the EVOLVE is to build a bridge between probability, set oriented numerics and evolutionary computing, as to identify new common and challenging research aspects. The conference is also intended to foster a growing interest for robust and efficient methods with a sound theoretical background. EVOLVE is intended to unify theory-inspired methods and cutting-edge techniques ensuring performance guarantee factors. By gathering researchers with different backgrounds, a unified view and vocabulary can emerge where the theoretical advancements may echo in different domains. Summarizing, the EVOLVE focuses on challenging aspects arising at the passage from theory to new paradigms and aims to provide a unified view while raising questions related to reliability,  performance guarantees and modeling. The papers of the EVOLVE 2012 make a contribution to this goal. 

Anaerobic microbiological method of cleaning water contaminated by metallurgical slags

Directory of Open Access Journals (Sweden)

Олена Леонідівна Дан

2015-11-01

Full Text Available The problem of environmental protection and rational use of water resources is one of the most important problems of environmental policy in Ukraine. This problem in Mariupol is particularly acute as metallurgical and coke industries cause significant damage to adjacent water bodies (the Kalchyk, the Kalmius and coastal zone of the Sea of Azov. One of the most harmful components of wastewater of these enterprises are sulfide-containing compounds. These compounds in water can cause great harm to both human health and the environment. For example, in 1999 the main city enterprises (AZOVSTAL IRON & STEEL WORKS and ILYICH IRON AND STEEL WORKS discharged 885,0 million m³ of wastewater (including 403,9 million m³ of polluted waste water into water bodies. The slag dumps and landfills in close proximity to the sea form a source of dangerous pollution, because contaminated water infiltration washed out here in the groundwater and surface water, get into the Sea of Azov later on. There are 97 mg/l of sulfides in the protective dam of AZOVSTAL IRON & STEEL WORKS, what exceeds the standards (MPC = 10 mg/l. It makes it possible for us to put forward biochemical purification processes. Anaerobic microbiological method proposed in the article has several advantages (compact hardware design, a minimum amount of activated sludge and lack of energy consumption for aeration over the existing wastewater treatment (chemical, mechanical, biological. The experimental procedure consisted in introducing the medium to be purified purified into microbial communities of high concentration (Thiobacillus «X», Thiobacillus concretivorus, which assimilated organic substances of the medium as a primary energy source. The kinetics of sulfide compounds removal by means of anaerobic microbiological method was considered. The effectiveness of wastewater treatment with changing purification process conditions has been also assessed (concentration of sulfides, reactor type, p

Synergetic use of lignite fly ash and metallurgical converter slag in geopolymer concrete

Directory of Open Access Journals (Sweden)

Gábor Mucsi

2014-08-01

Full Text Available The application and utilization of the industrial wastes and by-products in the construction industry is a key issue from an environmental and economic point of view. The increased use of lignite has substantially increased the available quantities of lignite fired power plant fly ash, which can be mainly classified as class C fly ash. The utilization of such raw material however has some difficulties. In the present paper lignite fired power station fly ash and metallurgical converter slag were used for the production of geopolymer concrete. The fly ash was used as a geopolymer based binder material, and a converter slag as aggregate, thus created a geopolymer concrete which contains mainly industrial wastes. As preliminary test experimental series were carried out using andesite as aggregate. The optimal aggregate/binder ratio was determined. The effect of the amount of alkaline activator solution in the binder, the aggregate type on the geopolymer concretes’ compressive strength and density was investigated. Furthermore, the physical properties - freeze-thaw resistance and particle size distribution - of the applied aggregates were measured as well. As a result of the experiments it was found that physical properties of the andesite and converter slag aggregate was close. Therefore andesite can be replaced by converter slag in the concrete mixture. Additionally, geopolymer concrete with nearly 20 MPa compressive strength was produced from class C fly ash and converter slag.

Near-surface modifications for improved crack tolerant behavior of high strength alloys: trends and prospects

International Nuclear Information System (INIS)

Hettche, L.R.; Rath, B.B.

1982-01-01

The purpose of this chapter is to examine the potential of surface modifications in improving the crack tolerant behavior of high strength alloys. Provides a critique of two of the most promising and versatile techniques: ion implantation and laser beam surface processing. Discusses crack tolerant properties; engineering characterization; publication trends and Department of Defense interests; and emergent surface modification techniques. Finds that the efficiency with which high strength alloys can be incorporated into a structure or component is dependent on the following crack tolerant properties: fracture toughness, fatigue resistance, sustained loading cracking resistance, fretting fatigue resistance, and hydrogen embrittlement resistance. Concludes that ion implantation and laser surface processing coupled with other advanced metallurgical procedures and fracture mechanic analyses provide the means to optimize both the bulk and surface controlled crack tolerant properties

Effects of Plasma ZrN Metallurgy and Shot Peening Duplex Treatment on Fretting Wear and Fretting Fatigue Behavior of Ti6Al4V Alloy.

Science.gov (United States)

Tang, Jingang; Liu, Daoxin; Zhang, Xiaohua; Du, Dongxing; Yu, Shouming

2016-03-23

A metallurgical zirconium nitride (ZrN) layer was fabricated using glow metallurgy using nitriding with zirconiuming prior treatment of the Ti6Al4V alloy. The microstructure, composition and microhardness of the corresponding layer were studied. The influence of this treatment on fretting wear (FW) and fretting fatigue (FF) behavior of the Ti6Al4V alloy was studied. The composite layer consisted of an 8-μm-thick ZrN compound layer and a 50-μm-thick nitrogen-rich Zr-Ti solid solution layer. The surface microhardness of the composite layer is 1775 HK 0.1 . A gradient in cross-sectional microhardness distribution exists in the layer. The plasma ZrN metallurgical layer improves the FW resistance of the Ti6Al4V alloy, but reduces the base FF resistance. This occurs because the improvement in surface hardness results in lowering of the toughness and increasing in the notch sensitivity. Compared with shot peening treatment, plasma ZrN metallurgy and shot peening composite treatment improves the FW resistance and enhances the FF resistance of the Ti6Al4V alloy. This is attributed to the introduction of a compressive stress field. The combination of toughness, strength, FW resistance and fatigue resistance enhance the FF resistance for titanium alloy.

Evolving Systems: An Outcome of Fondest Hopes and Wildest Dreams

Science.gov (United States)

Frost, Susan A.; Balas, Mark J.

2012-01-01

New theory is presented for evolving systems, which are autonomously controlled subsystems that self-assemble into a new evolved system with a higher purpose. Evolving systems of aerospace structures often require additional control when assembling to maintain stability during the entire evolution process. This is the concept of Adaptive Key Component Control that operates through one specific component to maintain stability during the evolution. In addition, this control must often overcome persistent disturbances that occur while the evolution is in progress. Theoretical results will be presented for Adaptive Key Component control for persistent disturbance rejection. An illustrative example will demonstrate the Adaptive Key Component controller on a system composed of rigid body and flexible body modes.

Metallurgical investigation of cracking of the isolation valve downstream piping of regenerative heat exchanger at beaver valley unit 1 station

International Nuclear Information System (INIS)

Rao, G.V.

1998-01-01

A metallurgical investigation was conducted to establish the mechanism and cause of cracking in the regenerative heat exchanger piping at Beaver Valley Unit 1 PWR station in the USA. The investigation, which was centered on an eight inch long pipe section containing the cracking included surface examinations, metallographic and fractographic examinations, and chemistry evaluations. The results of the examinations showed that there were two types of pipe degradation mechanisms that affected the type 304 stainless schedule 40 piping. These consisted of localized corrosive attack on the OD surface due to the presence of chlorides, sulphates and phosphates, and transgranular stress corrosion cracking in the pipe wall due to the presence of chloride contaminants. The overall results of the investigation showed that the introduction of contaminants from external sources other than pipe insulation was the cause of heat exchanger pipe cracking. (author)

Impact of the spatial distribution of morphological pattern on the efficiency of electrocatalytic gas evolving reactions

Directory of Open Access Journals (Sweden)

Žerađanin Aleksandar R.

2014-01-01

Full Text Available The efficiency of electrocatalytic gas evolving reactions (hydrogen, chlorine and oxygen evolution is a key challenge for the important industrial processes, such as chlor-alkali electrolysis or water electrolysis. Central issue for the aforementioned electrocatalytic processes is huge power consumption. Experimental results accumulated in the past, as well as some predictive models ("volcano" plots indicate that altering the nature of the electrode material cannot significantly increase the activity of mentioned reactions. Consequently, it is necessary to find a qualitatively different strategy for improving the energy efficiency of electrocatalytic gas evolving reactions. Usually disregarded fact is that the gas evolution is an oscillatory phenomenon. Given the oscillatory behavior, a key parameter of macrokinetics of gas electrode is the frequency of gas-bubble detachment. Bearing in mind that the gas evolution greatly depends on the surface morphology, a methodology is proposed that establishes a rational link between the morphological pattern of electrode with electrode activity and stability. Characterization was performed using advanced analytical tools. Frequency of gas-bubble detachment is obtained in the configuration of scanning electrochemical microscopy (SECM while the corrosion stability is analyzed using miniaturized scanning flow electrochemical cell connected to the mass spectrometer (SFC-ICPMS.

Translational behavioral medicine for population and individual health: gaps, opportunities, and vision for practice-based translational behavior change research.

Science.gov (United States)

Ma, Jun; Lewis, Megan A; Smyth, Joshua M

2018-04-12

In this commentary, we propose a vision for "practice-based translational behavior change research," which we define as clinical and public health practice-embedded research on the implementation, optimization, and fundamental mechanisms of behavioral interventions. This vision intends to be inclusive of important research elements for behavioral intervention development, testing, and implementation. We discuss important research gaps and conceptual and methodological advances in three key areas along the discovery (development) to delivery (implementation) continuum of evidence-based interventions to improve behavior and health that could help achieve our vision of practice-based translational behavior change research. We expect our proposed vision to be refined and evolve over time. Through highlighting critical gaps that can be addressed by integrating modern theoretical and methodological approaches across disciplines in behavioral medicine, we hope to inspire the development and funding of innovative research on more potent and implementable behavior change interventions for optimal population and individual health.

Neurodevelopmental Outcome in Children after Fetal Cardiac Intervention for Aortic Stenosis with Evolving Hypoplastic Left Heart Syndrome.

Science.gov (United States)

Laraja, Kristin; Sadhwani, Anjali; Tworetzky, Wayne; Marshall, Audrey C; Gauvreau, Kimberlee; Freud, Lindsay; Hass, Cara; Dunbar-Masterson, Carolyn; Ware, Janice; Lafranchi, Terra; Wilkins-Haug, Louise; Newburger, Jane W

2017-05-01

To characterize neurodevelopmental outcomes after fetal aortic valvuloplasty for evolving hypoplastic left heart syndrome and determine the risk factors for adverse neurodevelopment. Questionnaires were mailed to families of children who underwent fetal aortic valvuloplasty from 2000 to 2012, and medical records were reviewed retrospectively. The primary outcome was the General Adaptive Composite score of the Adaptive Behavior Assessment System Questionnaire-Second Edition. Other questionnaires included the Behavior Assessment System for Children, Behavior Rating Inventory of Executive Function, Ages and Stages, and Pediatric Quality of Life Inventory. Among 69 eligible subjects, 52 (75%) completed questionnaires at median age of 5.5 (range 1.3-12) years; 30 (58%) had biventricular status circulation. The General Adaptive Composite mean score (92 ± 17) was lower than population norms (P neurodevelopmental questionnaires (Behavior Assessment System for Children, Behavior Rating Inventory of Executive Function, Ages and Stages, Pediatric Quality of Life Inventory), most subscale scores for patients with biventricular and single ventricular status were similar. Children who underwent fetal aortic valvuloplasty have neurodevelopmental delay, similar to patients with hypoplastic left heart syndrome without fetal intervention. Achievement of biventricular circulation was not associated with better outcomes. We infer that innate patient factors and morbidity during infancy have the greatest effect on neurodevelopmental outcomes. Copyright © 2017 Elsevier Inc. All rights reserved.

Stress corrosion cracking of austenitic stainless steels in PWR primary water: an update of metallurgical investigations performed on French withdrawn components

International Nuclear Information System (INIS)

Boursier, J.M.; Gallet, S.; Rouillon, Y.; Bordes, P.

2002-01-01

Austenitic stainless steels (AISI 304, 304L, 316 and 316L) are largely used in Nuclear Power Plants because of their good resistance to corrosion and their satisfactory mechanical properties. Nevertheless, on various French PWR Nuclear Power Plants, several cases of corrosion have been encountered in auxiliary circuit portions where deleterious species and oxygen can be present. This paper focuses on the metallurgical investigations performed on pulled out components such as Canopy welds or 'dead legs' (auxiliary circuit portions connected to the main primary loops) in terms of cracking locations and degradation parameters. In addition, some comparisons between Nuclear Power Plant feedback and fundamental research and development studies are discussed, particularly in the scope of temperature, microstructure, stresses (applied and residual) and medium responsible for the degradation. (authors)

Evolving Procurement Organizations

DEFF Research Database (Denmark)

Bals, Lydia; Laiho, Aki; Laine, Jari

Procurement has to find further levers and advance its contribution to corporate goals continuously. This places pressure on its organization in order to facilitate its performance. Therefore, Procurement organizations constantly have to evolve in order to match these demands. A conceptual model...... is presented and results of a first case study discussed. The findings highlight the importance of taking a contingency perspective on Procurement organization, understanding the internal and internal contingency factors. From a theoretical perspective, it opens up insights that can be furthermore leveraged...... in future studies in the fields of hybrid procurement organizations, global sourcing organizations as well as international procurement offices (IPOs). From a practical standpoint, an assessment of external and internal contingencies provides the opportunity to consciously match organization to its...

Defy or ally : Neuroendocrine regulation of human socio-emotional behavior

NARCIS (Netherlands)

Hermans, E.J.

2006-01-01

Evolution has created a human brain that is characterized by a layered, hierarchical organization. These superimposed layers have gradually evolved to generate ever more complex forms of socio-emotional behavior. The present thesis centers on the neurobiological substrates that generate this

Effects of metallurgical factors on stress corrosion cracking of Ni-base alloys in high temperature water

International Nuclear Information System (INIS)

Yonezawa, T.; Sasaguri, N.; Onimura, K.

1988-01-01

Nickel-base Alloy 600 is the principal material used for the steam generator tubes of PWRs. Generally, this alloy has been proven to be satisfactory for this application, however when it is subjected to extremely high stress level in PWR primary water, it may suffer from stress corrosion cracking. The authors have systematically studied the effects of test temperature and such metallurgical factors as cold working, chemical composition and heat treatment on the stress corrosion cracking of Alloy 600 in high temperature water, and also on that of Alloy 690 which is a promising material for the tubes and may provide improved crrosion resistance for steam generators. The test materials, the stress corrosion cracking test and the test results are reported. When the test temperature was raise, the stress corrosion cracking of the nickel-base alloys was accelerated. The time of stress corrosion cracking occurrence decreased with increasing applied stress, and it occurred at the stress level higher than the 0.2 % offset proof stress of Alloy 600. In Alloy 690, stress corrosion cracking was not observed at such stress level. Cold worked Alloy 600 showed higher resistance to stress corrosion cracking than the annealed alloy. (Kako, I.)

Sulfur dioxide concentration measurements in the vicinity of the Albert Funk mining and metallurgical plant complex

Energy Technology Data Exchange (ETDEWEB)

Meyer, M

1976-01-01

This article discusses the ambient air concentration of sulfur dioxide in the area of Freiberg, GDR. The emission of sulfur dioxide results for the most part from brown coal combustion in heat and power plants and in metallurgical plants. Sulfur dioxide emission from neighboring industrial centers such as Dresden and North Bohemian towns affects the Freiburg area to some extent. The use of brown coal in household heating contributes an average of 50 kg of sulfur dioxide emission per coal burning household annually. A total of 1260 measurements at 28 points in the vicinity of Freiberg were made in the year 1972 in evaluating the concentration of sulfur dioxide present in the air. In 75% of the measurements the concentrations were below 0.15 mg/mat3, in 12% between 0.15 and 0.2 mg/mat3, in 7% between 0.2 and 0.3 mg/mat3 and in 6% between 0.3 and 0.5 mg/mat3. The results are described as average industrial pollution. The influence of air temperature, wind velocity, fog, season and time of day are also discussed. (4 refs.) (In German)

Evolved Control of Natural Plants: Crossing the Reality Gap for User-Defined Steering of Growth and Motion

DEFF Research Database (Denmark)

Hofstadler, Daniel Nicolas; Wahby, Mostafa; Heinrich, Mary Katherine

2017-01-01

Mixing societies of natural and artificial systems can provide interesting and potentially fruitful research targets. Here we mix robotic setups and natural plants in order to steer the motion behavior of plants while growing. The robotic setup uses a camera to observe the plant and uses a pair...... of light sources to trigger phototropic response, steering the plant to user-defined targets. An evolutionary robotic approach is used to design a controller for the setup. Initially, preliminary experiments are performed with a simple predetermined controller and a growing bean plant. The plant behavior......-evolved controller in the real setup controlling a natural bean plant. The results demonstrate a successful crossing of the reality gap in the setup. The success of the approach allows for future extensions to more complex tasks including control of the shape of plants and pattern formation in multiple plant setups....

The effect of thermal treatments on the corrosion behavior of friction stir welded 7050 and 7075 aluminum alloys

Energy Technology Data Exchange (ETDEWEB)

Lumsden, J.; Pollock, G.; Mahoney, M. [Rockwell Scientific, Camino dos Rios, Thousand Oaks, CA (United States)

2003-07-01

The rapid thermal cycle generated during friction stir welding (FSW) produces a gradient of microstructures and precipitate distributions in the weld heat affected zone (HAZ) and the thermo mechanical affected zone (TMAZ). Metallurgical transformations associated with such heating and cooling become complex under these nonequilibrium conditions, producing unstable microstructures, which cause unpredictable changes in properties relative to the parent alloy. Our work has shown that the composition changes caused by the nucleation and coarsening of precipitates during FSW produce a sensitized microstructure in 7050 and 7075 aluminum alloys. This paper describes the deleterious effects on the corrosion behavior of 7050 and 7075 aluminum alloys resulting from FSW and the effects of pre- and post- weld heat treatments on the corrosion properties of the welded material. (orig.)

Health-related behaviors and technology usage among college students.

Science.gov (United States)

Melton, Bridget F; Bigham, Lauren E; Bland, Helen W; Bird, Matthew; Fairman, Ciaran

2014-07-01

To examine associations between technology usage and specific health factors among college students. The research employed was a quantitative, descriptive, cross-sectional design; undergraduate students enrolled in spring 2012 general health education courses were recruited to participate. To explore college students' specific technology usage and health-related behaviors, a 28-item questionnaire was utilized. Statistical significant differences of technology usage were found between 3 of the 4 health-related behaviors under study (BMI, sleep, and nutrition) (p technology usage continues to evolve within the college student population, health professionals need to understand its implications on health behaviors.

Cosmic Biology How Life Could Evolve on Other Worlds

CERN Document Server

Irwin, Louis Neil

2011-01-01

It is very unlikely that little green humanoids are living on Mars. But what are the possible life forms that might exist in our Solar System and how might they have evolved? This uniquely authoritative and imaginative book on the possibilties for alien life addresses the intrinsic interest that we have about life on other worlds - reinforcing some of our assumptions and reshaping others. It introduces new possibilties that will enlarge our understanding of the issue overall, in particular the enormous range of environments and planetary conditions within which life might evolve. Cosmic Biology -discusses a broad range of possible environments where alien life might have evolved; -explains why carbon-based, water-borne life is more likely that its alternatives, but is not the only possiblity; -applies the principles of planetary science and modern biology to evolutionary scenarios on other worlds; -looks at the future fates of living systems, including those on Earth.

WSC-07: Evolving the Web Services Challenge

NARCIS (Netherlands)

Blake, M. Brian; Cheung, William K.W.; Jaeger, Michael C.; Wombacher, Andreas

Service-oriented architecture (SOA) is an evolving architectural paradigm where businesses can expose their capabilities as modular, network-accessible software services. By decomposing capabilities into modular services, organizations can share their offerings at multiple levels of granularity

(N+1)-dimensional Lorentzian evolving wormholes supported by polytropic matter

Energy Technology Data Exchange (ETDEWEB)

Cataldo, Mauricio [Universidad del Bio-Bio, Departamento de Fisica, Facultad de Ciencias, Concepcion (Chile); Arostica, Fernanda; Bahamonde, Sebastian [Universidad de Concepcion, Departamento de Fisica, Concepcion (Chile)

2013-08-15

In this paper we study (N+1)-dimensional evolving wormholes supported by energy satisfying a polytropic equation of state. The considered evolving wormhole models are described by a constant redshift function and generalizes the standard flat Friedmann-Robertson-Walker spacetime. The polytropic equation of state allows us to consider in (3+1)-dimensions generalizations of the phantom energy and the generalized Chaplygin gas sources. (orig.)

Revealing evolved massive stars with Spitzer

Science.gov (United States)

Gvaramadze, V. V.; Kniazev, A. Y.; Fabrika, S.

2010-06-01

Massive evolved stars lose a large fraction of their mass via copious stellar wind or instant outbursts. During certain evolutionary phases, they can be identified by the presence of their circumstellar nebulae. In this paper, we present the results of a search for compact nebulae (reminiscent of circumstellar nebulae around evolved massive stars) using archival 24-μm data obtained with the Multiband Imaging Photometer for Spitzer. We have discovered 115 nebulae, most of which bear a striking resemblance to the circumstellar nebulae associated with luminous blue variables (LBVs) and late WN-type (WNL) Wolf-Rayet (WR) stars in the Milky Way and the Large Magellanic Cloud (LMC). We interpret this similarity as an indication that the central stars of detected nebulae are either LBVs or related evolved massive stars. Our interpretation is supported by follow-up spectroscopy of two dozen of these central stars, most of which turn out to be either candidate LBVs (cLBVs), blue supergiants or WNL stars. We expect that the forthcoming spectroscopy of the remaining objects from our list, accompanied by the spectrophotometric monitoring of the already discovered cLBVs, will further increase the known population of Galactic LBVs. This, in turn, will have profound consequences for better understanding the LBV phenomenon and its role in the transition between hydrogen-burning O stars and helium-burning WR stars. We also report on the detection of an arc-like structure attached to the cLBV HD 326823 and an arc associated with the LBV R99 (HD 269445) in the LMC. Partially based on observations collected at the German-Spanish Astronomical Centre, Calar Alto, jointly operated by the Max-Planck-Institut für Astronomie Heidelberg and the Instituto de Astrofísica de Andalucía (CSIC). E-mail: vgvaram@mx.iki.rssi.ru (VVG); akniazev@saao.ac.za (AYK); fabrika@sao.ru (SF)

Evolving NASA's Earth Science Data Systems

Science.gov (United States)

Walter, J.; Behnke, J.; Murphy, K. J.; Lowe, D. R.

2013-12-01

NASA's Earth Science Data and Information System Project (ESDIS) is charged with managing, maintaining, and evolving NASA's Earth Observing System Data and Information System (EOSDIS) and is responsible for processing, archiving, and distributing NASA Earth science data. The system supports a multitude of missions and serves diverse science research and other user communities. Keeping up with ever-changing information technology and figuring out how to leverage those changes across such a large system in order to continuously improve and meet the needs of a diverse user community is a significant challenge. Maintaining and evolving the system architecture and infrastructure is a continuous and multi-layered effort. It requires a balance between a "top down" management paradigm that provides a coherent system view and maintaining the managerial, technological, and functional independence of the individual system elements. This presentation will describe some of the key elements of the current system architecture, some of the strategies and processes we employ to meet these challenges, current and future challenges, and some ideas for meeting those challenges.

Cognitive-behavioral and operant-behavioral therapy for people with fibromyalgia

Directory of Open Access Journals (Sweden)

D.C. Turk

2012-09-01

Full Text Available The current article reviews the cognitive-behavioral (CB and operant-behavioral perspectives on chronic pain and suggests an answer to the question why changes in behaviors, attitudes, and emotions are associated with decreases in pain severity and impact discussing potential psychobiological mechanisms that may underlie cognitive and behavioral techniques. The impact of learning such as classical and operant conditioning in behaviors and physical responses including baroreflex sensitivity (BRS, as well as the influence of cognitions on pain perception and impact will be presented to explain general efficacy of cognitive-behavior therapy (CBT and operant-behavioral therapy (OBT in the treatment of people with fibromyalgia (FM describing some of the limitations of published outcome studies. We discuss advances in moderation and mediation of treatment outcomes. Lastly, we will discuss the need for research that takes into account evidence-based medicine, methods that address treatment responders and non-responders, individual trajectories, how we might advance and refine CBT and OBT, and strategies related to relapse prevention, maintenance, and adherence-enhancement taking advantage of evolving, technological methods of service delivery. We provide recommendations of how to move forward in approaching studies of CBT and OBT efficacy as a function of better understanding of patient characteristics and contextual factors. We advocate for the potential of the CB perspective and principle of learning for all health care providers regardless of discipline or training and will give examples for making more effective the patient-rheumatologist-relationship by using the principles discussed.

Ex situ characterization of metallurgical inclusions in X100 pipeline steel before and after immersion in a neutral pH bicarbonate solution

International Nuclear Information System (INIS)

Li, Yingbo; Liu, Jie; Deng, Yida; Han, Xiaopeng; Hu, Wenbin; Zhong, Cheng

2016-01-01

The initiation of corrosion pits in pipeline steels plays an important role in the development of stress corrosion cracking. In order to reveal the effect of inclusions on corrosion initiation sites and also to clarify contradictory results from previous literature, we proposed an ex situ characterization method that is allowed to characterize exactly the same inclusion or location of the surface of steel before and after corrosion tests. The time-dependent corrosion behaviour of the inclusions and the surrounding X100 steel matrix at the same area before and after early stage immersion in a near-neutral pH bicarbonate solution was investigated by ex situ scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) analysis and localized electrochemical impedance spectroscopy (LEIS). The sizes of most inclusions in X100 steel are below 3 μm. The results challenge the long-held opinion of previous work that corrosion pit initiations are related with the inclusions. It has been found that most of the inclusions remain stable (intact) during the whole testing time although severe corrosion occurs on the matrix of the steel. The chemical composition of the inclusion greatly affects the chemical stability of the inclusion. SiO_2 inclusions and complex inclusions with a high SiO_2 content remain intact although obvious general corrosion occurs on the steel matrix under the investigated immersion period. Inclusions with little Si, such as Al–Mg–Ca–O enriched inclusions, totally disappear after certain immersion time. During the immersion, the corrosion product tends to deposit at the interstice between the inclusion and steel matrix. - Highlights: • Ex situ characterization of metallurgical inclusions in X100 pipeline steel. • The pipeline steel was immersed in neutral pH bicarbonate solution. • Majority of inclusions remain stable during the whole testing time. • The chemical stability of metallurgical inclusions depends on the SiO_2 content.

Ex situ characterization of metallurgical inclusions in X100 pipeline steel before and after immersion in a neutral pH bicarbonate solution

Energy Technology Data Exchange (ETDEWEB)

Li, Yingbo; Liu, Jie [Key Laboratory of Advanced Ceramics and Machining Technology (Ministry of Education), School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Deng, Yida [Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China); Han, Xiaopeng [Key Laboratory of Advanced Ceramics and Machining Technology (Ministry of Education), School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Hu, Wenbin [Key Laboratory of Advanced Ceramics and Machining Technology (Ministry of Education), School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China); Zhong, Cheng, E-mail: cheng.zhong@tju.edu.cn [Key Laboratory of Advanced Ceramics and Machining Technology (Ministry of Education), School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China)

2016-07-15

The initiation of corrosion pits in pipeline steels plays an important role in the development of stress corrosion cracking. In order to reveal the effect of inclusions on corrosion initiation sites and also to clarify contradictory results from previous literature, we proposed an ex situ characterization method that is allowed to characterize exactly the same inclusion or location of the surface of steel before and after corrosion tests. The time-dependent corrosion behaviour of the inclusions and the surrounding X100 steel matrix at the same area before and after early stage immersion in a near-neutral pH bicarbonate solution was investigated by ex situ scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) analysis and localized electrochemical impedance spectroscopy (LEIS). The sizes of most inclusions in X100 steel are below 3 μm. The results challenge the long-held opinion of previous work that corrosion pit initiations are related with the inclusions. It has been found that most of the inclusions remain stable (intact) during the whole testing time although severe corrosion occurs on the matrix of the steel. The chemical composition of the inclusion greatly affects the chemical stability of the inclusion. SiO{sub 2} inclusions and complex inclusions with a high SiO{sub 2} content remain intact although obvious general corrosion occurs on the steel matrix under the investigated immersion period. Inclusions with little Si, such as Al–Mg–Ca–O enriched inclusions, totally disappear after certain immersion time. During the immersion, the corrosion product tends to deposit at the interstice between the inclusion and steel matrix. - Highlights: • Ex situ characterization of metallurgical inclusions in X100 pipeline steel. • The pipeline steel was immersed in neutral pH bicarbonate solution. • Majority of inclusions remain stable during the whole testing time. • The chemical stability of metallurgical inclusions depends on the SiO{sub 2

Sex determination: ways to evolve a hermaphrodite.

OpenAIRE

Braendle , Christian; Félix , Marie-Anne

2006-01-01

Most species of the nematode genus Caenorhabditis reproduce through males and females; C. elegans and C. briggsae, however, produce self-fertile hermaphrodites instead of females. These transitions to hermaphroditism evolved convergently through distinct modifications of germline sex determination mechanisms.

Preliminary results on air pollution inside an iron metallurgical plant, using rotating streaker sampler and energy dispersive X-ray microfluorescence

International Nuclear Information System (INIS)

Nascimento Filho, V.F.; Silva, R.M.C.; Perez, C.A.

2005-01-01

Our aim was to study the chemical concentration of some metals in suspended particulate matter inside an-iron metallurgical plant. Using a rotating streaker air-particulate sampler with 8 and 0.45 microns pore diameter filter, it was possible to collect coarse and fine particulates during a week, with one hour step. After this, each strip of the filter was analyzed by energy dispersive x-ray microfluorescence (μ-EDXRF), using in the excitation a collimated x-ray line beam from a Mo target tube (30 kV, 20 mA, Zr filter) with a quartz capillary (120 mm long, 10 mm entrance diameter and 20 microns inner diameter at exit). The detection was carried out using a Si(Li) semiconductor detector coupled to a multichannel analyzer, and the X-ray spectra were fitted with the AXIL software. The profiles of several elements are shown and the results are discussed.

Obtainment of metallurgic coke from hydrolytic lignin of eucalyptus; Obtencao de coque metalurgico a partir de lignina hidrolitica de eucalipto

Energy Technology Data Exchange (ETDEWEB)

Nascimento, E.A. do [Escola Federal de Uberlandia, MG (Brazil). Dept. de Quimica; Schuchardt, U. [Universidade Estadual de Campinas, SP (Brazil). Inst. de Quimica

1987-12-31

Eucalyptus lignin, obtained from COALBRA S.A., was briquetted under different humidities and pressures. The briquettes were heated to 900 Celsius at 1 C/min in a cylindric bench-scale oven. The cokification was accompanied by carbon-13 nuclear magnetic resonance measurements. The coke obtained was submitted to approximate and elementary analysis and its abrasion and compression strengths were determined. The distribution and total pore volume were investigated by high-pressure mercury porosimetry and the surface texture analyzed by scanning electron microscopy. The best coke was obtained in 48% yield from the briquettes with 10% humidity and 100 MPa pressure. This showed a high structural resistance, a smooth surface with continuous metallic brilliance and well defined pore volume and distribution. The coke obtained is a high-quality metallurgic reductant whose properties surpass by far the specifications required. (author). 12 refs., 1 fig., 2 tabs

Influence of trees and shrubs on microclimate and sanitary state of air layers close to the ground surface at industrial sites of metallurgical works

Energy Technology Data Exchange (ETDEWEB)

Reva, M L; Filatova, R Ya

1976-01-01

The effect of trees and shrubs on working conditions was investigated at metallurgical works in the Ukraine. Indices used included air temperature and humidity, sulfuric anhydride, carbon monoxide and nitrogen oxide content. Indices were measured at varying distances from the sources of the industrial waste. In areas with trees and shrubs, air temperature was 3 to 5 degrees lower and relative humidity 8 to 10 degrees higher than out in the open. The level of industrial waste given off as gas was consistently less prevalent in areas with trees and shrubs than out in the open. Trees and shrubs were concluded to be essential for the health and well-being of the workers.

The Evolution of "Enhanced" Cognitive Behavior Therapy for Eating Disorders: Learning from Treatment Nonresponse

Science.gov (United States)

Cooper, Zafra; Fairburn, Christopher G.

2011-01-01

In recent years there has been widespread acceptance that cognitive behavior therapy (CBT) is the treatment of choice for bulimia nervosa. The cognitive behavioral treatment of bulimia nervosa (CBT-BN) was first described in 1981. Over the past decades the theory and treatment have evolved in response to a variety of challenges. The treatment has…

Satcom access in the Evolved Packet Core

NARCIS (Netherlands)

Cano Soveri, M.D.; Norp, A.H.J.; Popova, M.P.

2011-01-01

Satellite communications (Satcom) networks are increasingly integrating with terrestrial communications networks, namely Next Generation Networks (NGN). In the area of NGN the Evolved Packet Core (EPC) is a new network architecture that can support multiple access technologies. When Satcom is

Satcom access in the evolved packet core

NARCIS (Netherlands)

Cano, M.D.; Norp, A.H.J.; Popova, M.P.

2012-01-01

Satellite communications (Satcom) networks are increasingly integrating with terrestrial communications networks, namely Next Generation Networks (NGN). In the area of NGN the Evolved Packet Core (EPC) is a new network architecture that can support multiple access technologies. When Satcom is

Real-time evolvable pulse shaper for radiation measurements

Energy Technology Data Exchange (ETDEWEB)

Lanchares, Juan, E-mail: julandan@dacya.ucm.es [Facultad de Informática, Universidad Complutense de Madrid (UCM), C/Prof. José García Santesmases s/n, 28040 Madrid (Spain); Garnica, Oscar, E-mail: ogarnica@dacya.ucm.es [Facultad de Informática, Universidad Complutense de Madrid (UCM), C/Prof. José García Santesmases s/n, 28040 Madrid (Spain); Risco-Martín, José L., E-mail: jlrisco@dacya.ucm.es [Facultad de Informática, Universidad Complutense de Madrid (UCM), C/Prof. José García Santesmases s/n, 28040 Madrid (Spain); Ignacio Hidalgo, J., E-mail: hidalgo@dacya.ucm.es [Facultad de Informática, Universidad Complutense de Madrid (UCM), C/Prof. José García Santesmases s/n, 28040 Madrid (Spain); Regadío, Alberto, E-mail: alberto.regadio@insa.es [Área de Tecnologías Electrónicas, Instituto Nacional de Técnica Aeroespacial (INTA), 28850 Torrejón de Ardoz, Madrid (Spain)

2013-11-01

In the last two decades, recursive algorithms for real-time digital pulse shaping in pulse height measurements have been developed and published in number of articles and textbooks. All these algorithms try to synthesize in real time optimum or near optimum shapes in the presence of noise. Even though some of these shapers can be considered effective designs, some side effects like aging cannot be ignored. We may observe that after sensors degradation, the signal obtained is not valid. In this regard, we present in this paper a novel technique that, based on evolvable hardware concepts, is able to evolve the degenerated shaper into a new design with better performance than the original one under the new sensor features.

Handed behavior in hagfish--an ancient vertebrate lineage--and a survey of lateralized behaviors in other invertebrate chordates and elongate vertebrates.

Science.gov (United States)

Miyashita, Tetsuto; Palmer, A Richard

2014-04-01

Hagfish represent an ancient lineage of boneless and jawless vertebrates. Among several curious behaviors they exhibit, solitary individuals in one dominant genus of hagfish (Eptatretus spp.) regularly rest in a tightly coiled posture. We present the first systematic treatment of this distinctive behavior. Individual northeastern Pacific hagfish (E. stoutii) exhibited significant handedness (preferred orientation of coiling). However, right-coiling and left-coiling individuals were equally common in the population. Individual hagfish likely develop a preference for one direction by repeating the preceding coiling direction. We also revisit classical accounts of chordate natural history and compare the coiling behavior of Eptatretus with other handed or lateralized behaviors in non-vertebrate chordates, lampreys, and derived vertebrates with elongate bodies. Handed behaviors occur in many of these groups, but they likely evolved independently. In contrast to vertebrates, morphological asymmetries may bias lateralized larval behaviors toward one side in cephalochordates and tunicates. As a consequence, no known handed behavior can be inferred to have existed in the common ancestor of vertebrates.

Evolving chemometric models for predicting dynamic process parameters in viscose production

Energy Technology Data Exchange (ETDEWEB)

Cernuda, Carlos [Department of Knowledge-Based Mathematical Systems, Johannes Kepler University Linz (Austria); Lughofer, Edwin, E-mail: edwin.lughofer@jku.at [Department of Knowledge-Based Mathematical Systems, Johannes Kepler University Linz (Austria); Suppan, Lisbeth [Kompetenzzentrum Holz GmbH, St. Peter-Str. 25, 4021 Linz (Austria); Roeder, Thomas; Schmuck, Roman [Lenzing AG, 4860 Lenzing (Austria); Hintenaus, Peter [Software Research Center, Paris Lodron University Salzburg (Austria); Maerzinger, Wolfgang [i-RED Infrarot Systeme GmbH, Linz (Austria); Kasberger, Juergen [Recendt GmbH, Linz (Austria)

2012-05-06

Highlights: Black-Right-Pointing-Pointer Quality assurance of process parameters in viscose production. Black-Right-Pointing-Pointer Automatic prediction of spin-bath concentrations based on FTNIR spectra. Black-Right-Pointing-Pointer Evolving chemometric models for efficiently handling changing system dynamics over time (no time-intensive re-calibration needed). Black-Right-Pointing-Pointer Significant reduction of huge errors produced by statistical state-of-the-art calibration methods. Black-Right-Pointing-Pointer Sufficient flexibility achieved by gradual forgetting mechanisms. - Abstract: In viscose production, it is important to monitor three process parameters in order to assure a high quality of the final product: the concentrations of H{sub 2}SO{sub 4}, Na{sub 2}SO{sub 4} and Z{sub n}SO{sub 4}. During on-line production these process parameters usually show a quite high dynamics depending on the fiber type that is produced. Thus, conventional chemometric models, which are trained based on collected calibration spectra from Fourier transform near infrared (FT-NIR) measurements and kept fixed during the whole life-time of the on-line process, show a quite imprecise and unreliable behavior when predicting the concentrations of new on-line data. In this paper, we are demonstrating evolving chemometric models which are able to adapt automatically to varying process dynamics by updating their inner structures and parameters in a single-pass incremental manner. These models exploit the Takagi-Sugeno fuzzy model architecture, being able to model flexibly different degrees of non-linearities implicitly contained in the mapping between near infrared spectra (NIR) and reference values. Updating the inner structures is achieved by moving the position of already existing local regions and by evolving (increasing non-linearity) or merging (decreasing non-linearity) new local linear predictors on demand, which are guided by distance-based and similarity criteria. Gradual

Phylogenetic footprints in organizational behavior

OpenAIRE

Witt, Ulrich; Schwesinger, Georg

2012-01-01

An evolutionary tool kit is applied in this paper to explain how innate social behavior traits evolved in early human groups. These traits were adapted to the particular production requirements of the group in human phylogeny. They shaped the group members' attitudes towards contributing to the group's goals and towards other group members. We argue that these attitudes are still present in modern humans and leave their phylogenetic footprints also in present-day organizational life. We discu...

Sextant: Visualizing time-evolving linked geospatial data

NARCIS (Netherlands)

C. Nikolaou (Charalampos); K. Dogani (Kallirroi); K. Bereta (Konstantina); G. Garbis (George); M. Karpathiotakis (Manos); K. Kyzirakos (Konstantinos); M. Koubarakis (Manolis)

2015-01-01

textabstractThe linked open data cloud is constantly evolving as datasets get continuously updated with newer versions. As a result, representing, querying, and visualizing the temporal dimension of linked data is crucial. This is especially important for geospatial datasets that form the backbone

Microstructure and Corrosion Behavior of Laser Synthesized Cobalt Based Powder on Ti-6Al-4V

Science.gov (United States)

Adesina, O. S.; Popoola, A. P. I.; Pityana, S. L.; Oloruntoba, D. T.

2018-05-01

The corrosion behavior of titanium alloys when used for various dynamic offshore components has been a major concern of titanium drilling risers in deepwater energy extraction. A way of achieving specified requirement is the development of coatings suitable to protect the base material against corrosion. In this work, laser cladding technique which is known as a leading edge due to its distinctive properties and outcomes was used in synthesizing Co-based powder on titanium alloy. The processing parameters used were laser power of 900W; scan speed of 0.6 to 1.2 m/min; powderfeedrate1.0g/min;beamspotsize3mm;gasflowrate1.2L/min.The effects of cobalt addition and laser parameters on corrosion behavior of laser clad Ti6AL4V coating in 0.5M sulfuric medium were investigated using linear potentiodynamic polarization. The changes in microstructure and corrosion behavior were analyzed using scanning electron microscopy (SEM) while the X –ray diffraction (XRD) indicates the intermetallics in the coatings. Results showed that the coatings displayed good metallurgical bonding with dendritic formations between the coatings and the substrate. The anodic current density increased with lower scan speed. However, the corrosion current densities of laser-clad samples were lower than Ti6Al4V alloy.

Behavioral Immunity Suppresses an Epizootic in Caribbean Spiny Lobsters.

Science.gov (United States)

Butler, Mark J; Behringer, Donald C; Dolan, Thomas W; Moss, Jessica; Shields, Jeffrey D

2015-01-01

Sociality has evolved in a wide range of animal taxa but infectious diseases spread rapidly in populations of aggregated individuals, potentially negating the advantages of their social interactions. To disengage from the coevolutionary struggle with pathogens, some hosts have evolved various forms of "behavioral immunity"; yet, the effectiveness of such behaviors in controlling epizootics in the wild is untested. Here we show how one form of behavioral immunity (i.e., the aversion of diseased conspecifics) practiced by Caribbean spiny lobsters (Panulirus argus) when subject to the socially transmitted PaV1 virus, appears to have prevented an epizootic over a large seascape. We capitalized on a "natural experiment" in which a die-off of sponges in the Florida Keys (USA) resulted in a loss of shelters for juvenile lobsters over a ~2500km2 region. Lobsters were thus concentrated in the few remaining shelters, presumably increasing their exposure to the contagious virus. Despite this spatial reorganization of the population, viral prevalence in lobsters remained unchanged after the sponge die-off and for years thereafter. A field experiment in which we introduced either a healthy or PaV1-infected lobster into lobster aggregations in natural dens confirmed that spiny lobsters practice behavioral immunity. Healthy lobsters vacated dens occupied by PaV1-infected lobsters despite the scarcity of alternative shelters and the higher risk of predation they faced when searching for a new den. Simulations from a spatially-explicit, individual-based model confirmed our empirical results, demonstrating the efficacy of behavioral immunity in preventing epizootics in this system.