Dissociative scattering of low-energy SiF{sub 3}{sup +} and SiF{sup +} ions (5-200 eV) on Cu(100) surface

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, Hiroyuki; Baba, Yuji; Sasaki, T A [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-03-01

Dissociative scattering of molecular SiF{sub 3}{sup +} and SiF{sup +} ions from a Cu(100) single crystal surface has been investigated in the incident energy range from 5 eV to 200 eV with a scattering angle of 77deg. The scattered ion intensity of dissociative ions and parent molecular ions were measured as a function of incident ion energy. The observed data show that onset energies of dissociation for SiF{sub 3}{sup +} and SiF{sup +} ions are 30 eV and 40 eV, respectively. The obtained threshold energies are consistent with a impulsive collision model where the dissociation of incident ion is caused by vibrational excitation during collision. (author)

Tables and graphs of electron-interaction cross sections from 10 eV to 100 GeV derived from the LLNL Evaluated Electron Data Library (EEDL), Z = 1--100

Energy Technology Data Exchange (ETDEWEB)

Perkins, S.T.; Cullen, D.E. (Lawrence Livermore National Lab., CA (United States)); Seltzer, S.M. (National Inst. of Standards and Technology (NML), Gaithersburg, MD (United States). Center for Radiation Research)

1991-11-12

Energy-dependent evaluated electron interaction cross sections and related parameters are presented for elements H through Fm (Z = 1 to 100). Data are given over the energy range from 10 eV to 100 GeV. Cross sections and average energy deposits are presented in tabulated and graphic form. In addition, ionization cross sections and average energy deposits for each shell are presented in graphic form. This information is derived from the Livermore Evaluated Electron Data Library (EEDL) as of July, 1991.

Information on 'Shikoku EV Rally Festival 99' and analysis of participating EVs

Energy Technology Data Exchange (ETDEWEB)

Miyashita, K. [Naruto Univ. of Education, Takashima (Japan)

2000-07-01

A 3 day rally was held in August 1999 in the city of Shikoku, Japan to bring electric vehicles (EVs) to the public's attention. A total of 39 EVs from 3 production series participated. This included 29 EVs converted from internal combustion engine vehicles, 5 prototype EVs and 2 hybrid electric vehicles. Thirty seven of the EVs used lead-acid batteries, one used nickel-metal hydride batteries and one used lithium-ion batteries. Each one was charged using one outlet of 3 phase 200 V, 1 phase 200 V or 1 phase 100 V at temporary charging facilities. The 340 km course ran through the city and in mountainous regions. The EVs were driven according to normal traffic rules. At the end of the rally, each EV was evaluated for their performance, hill climbing ability, and re-charging time. Several of the converted EVs drove for more than 50 km through mountainous regions using lead-acid batteries. It was determined that the poor range of EVs can be improved by an efficient daily re-charge. refs.

Evaluation of the 235U fission cross-section from 100 eV to 20 MeV

International Nuclear Information System (INIS)

Bhat, M.R.

1976-01-01

The evaluation of the 235 U fission cross section from 100 eV to 20 MeV for ENDF/B-V is described. The evaluated average cross sections from 100 eV to 200 keV are given, and it is proposed to include structure in the cross section in this energy region. Above 200 keV, the cross section is given as a smooth curve, and is recommended as a standard. Preliminary error estimates in the cross section are also given

THE ROLL-OVER OF HELIOSPHERIC NEUTRAL HYDROGEN BELOW 100 eV: OBSERVATIONS AND IMPLICATIONS

Energy Technology Data Exchange (ETDEWEB)

Galli, A.; Wurz, P. [Physics Institute, University of Bern, Bern, 3012 (Switzerland); Schwadron, N. A.; Kucharek, H.; Möbius, E. [University of New Hampshire, Durham, NH 03824 (United States); Bzowski, M.; Sokół, J. M.; Kubiak, M. A. [Space Research Centre, Polish Academy of Sciences, Warsaw, 00-716 (Poland); Funsten, H. O. [Los Alamos National Laboratory, Intelligence and Space Research Division, Los Alamos, NM 87545 (United States); Fuselier, S. A.; McComas, D. J. [Southwest Research Institute, San Antonio, TX 78228 (United States)

2016-04-20

We present an improved analysis of the energy spectrum of energetic neutral hydrogen from the heliosheath observed with the IBEX -Lo sensor on the Interstellar Boundary EXplorer from the years 2009 to 2012. This analysis allows us to study the lowest energies between 10 and 100 eV although various background sources are more intense than the targeted signal over broad areas of the sky. The results improve our knowledge of the interaction region between our heliosphere and the interstellar plasma because these neutral atoms are direct messengers from the low-energy plasma in the heliosheath. We find a roll-over of the energy spectrum below 100 eV, which has major implications for the pressure balance of the plasma in the inner heliosheath. The results can also be compared directly with in situ observations of the Voyager 1 and 2 spacecraft.

Photoabsorption and S 2p photoionization of the SF6 molecule: resonances in the excitation energy range of 200-280 eV.

Science.gov (United States)

Stener, M; Bolognesi, P; Coreno, M; O'Keeffe, P; Feyer, V; Fronzoni, G; Decleva, P; Avaldi, L; Kivimäki, A

2011-05-07

Photoabsorption and S 2p photoionization of the SF(6) molecule have been studied experimentally and theoretically in the excitation energy range up to 100 eV above the S 2p ionization potentials. In addition to the well-known 2t(2g) and 4e(g) shape resonances, the spin-orbit-resolved S 2p photoionization cross sections display two weak resonances between 200 and 210 eV, a wide resonance around 217 eV, a Fano-type resonance around 240 eV, and a second wide resonance around 260 eV. Calculations based on time-dependent density functional theory allow us to assign the 217-eV and 260-eV features to the shape resonances in S 2p photoionization. The Fano resonance is caused by the interference between the direct S 2p photoionization channel and the resonant channel that results from the participator decay of the S 2s(-1)6t(1u) excited state. The weak resonances below 210-eV photon energy, not predicted by theory, are tentatively suggested to originate from the coupling between S 2p shake-up photoionization and S 2p single-hole photoionization. The experimental and calculated angular anisotropy parameters for S 2p photoionization are in good agreement.

Picosecond x-ray measurements from 100 eV to 30 keV

International Nuclear Information System (INIS)

Attwood, D.T.; Kauffman, R.L.; Stradling, G.L.

1980-01-01

Picosecond x-ray measurements relevant to the Livermore Laser Fusion Program are reviewed. Resolved to 15 picoseconds, streak camera detection capabilities extend from 100 eV to higher than 30 keV, with synchronous capabilities in the visible, near infrared, and ultraviolet. Capabilities include automated data retrieval using charge coupled devices (CCD's), absolute x-ray intensity levels, novel cathodes, x-ray mirror/reflector combinations, and a variety of x-ray imaging devices

Development of nickel/metal-hydride batteries for EVs and HEVs

Science.gov (United States)

Taniguchi, Akihiro; Fujioka, Noriyuki; Ikoma, Munehisa; Ohta, Akira

This paper is to introduce the nickel/metal-hydride (Ni/MH) batteries for electric vehicles (EVs) and hybrid electric vehicles (HEVs) developed and mass-produced by our company. EV-95 for EVs enables a vehicle to drive approximately 200 km per charge. As the specific power is extremely high, more than 200 W/kg at 80% depth of discharge (DOD), the acceleration performance is equivalent to that of gasoline fuel automobiles. The life characteristic is also superior. This battery gives the satisfactory result of more than 1000 cycles in bench tests and approximately 4-year on-board driving. EV-28 developed for small EVs comprises of a compact and light battery module with high specific power of 300 W/kg at 80% DOD by introducing a new technology for internal cell connection. Meanwhile, our cylindrical battery for the HEV was adopted into the first generation Toyota Prius in 1997 which is the world's first mass-product HEV, and has a high specific power of 600 W/kg. Its life characteristic was found to be equivalent to more than 100,000 km driving. Furthermore, a new prismatic module in which six cells are connected internally was used for the second generation Prius in 2000. The prismatic battery comprises of a compact and light battery pack with a high specific power of 1000 W/kg, which is approximately 1.7 times that of conventional cylindrical batteries, as a consequence of the development of a new internal cell connection and a new current collection structure.

Electron-photon angular correlation measurements for excitation of the 2P state of hydrogen at 55 and 100 eV

International Nuclear Information System (INIS)

Slevin, J.; Eminyan, M.; Woolsey, J.M.; Vassilev, G.; Porter, H.Q.

1980-01-01

Electron-photon angular correlations have been measured for excitation of the 2P state of hydrogen at incident energies of 55 and 100 eV. The data presented extend the results of Weigold and co-workers (Flinders Univ. preprint (1980)) to smaller scattering angles and reveal the existence of a deep minimum in the parameter lambda thetasub(e) = 10 0 at and incident electron energy of 100 eV. (author)

Ion-beam doping of GaAs with low-energy (100 eV) C + using combined ion-beam and molecular-beam epitaxy

Science.gov (United States)

Iida, Tsutomu; Makita, Yunosuke; Kimura, Shinji; Winter, Stefan; Yamada, Akimasa; Fons, Paul; Uekusa, Shin-ichiro

1995-01-01

A combined ion-beam and molecular-beam-epitaxy (CIBMBE) system has been developed. This system consists of an ion implanter capable of producing ions in the energy range of 30 eV-30 keV and conventional solid-source MBE. As a successful application of CIBMBE, low-energy (100 eV) carbon ion (C+) irradiation during MBE growth of GaAs was carried out at substrate temperatures Tg between 500 and 590 °C. C+-doped layers were characterized by low-temperature (2 K) photoluminescence (PL), Raman scattering, and van der Pauw measurements. PL spectra of undoped GaAs grown by CIBMBE revealed that unintentional impurity incorporation into the epilayer is extremely small and precise doping effects are observable. CAs acceptor-related emissions such as ``g,'' [g-g], and [g-g]β are observed and their spectra are significantly changed with increasing C+ beam current density Ic. PL measurements showed that C atoms were efficiently incorporated during MBE growth by CIBMBE and were optically well activated as an acceptor in the as-grown condition even for Tg as low as 500 °C. Raman measurement showed negligible lattice damage of the epilayer bombarded with 100 eV C+ with no subsequent heat treatment. These results indicate that contamination- and damage-free impurity doping without postgrowth annealing can be achieved by the CIBMBE method.

Ion-beam doping of GaAs with low-energy (100 eV) C(+) using combined ion-beam and molecular-beam epitaxy

Science.gov (United States)

Lida, Tsutomu; Makita, Yunosuke; Kimura, Shinji; Winter, Stefan; Yamada, Akimasa; Fons, Paul; Uekusa, Shin-Ichiro

1995-01-01

A combined ion-beam and molecular-beam-epitaxy (CIBMBE) system has been developed. This system consists of an ion implanter capable of producing ions in the energy range of 30 eV - 30 keV and conventional solid-source MBE. As a successful application of CIBMBE, low-energy (100 eV) carbon ion (C(+)) irradiation during MBE growth of GaAs was carried out at substrate temperatures T(sub g) between 500 and 590 C. C(+)-doped layers were characterized by low-temperature (2 K) photoluminescence (PL), Raman scattering, and van der Pauw measurements. PL spectra of undoped GaAs grown by CIBMBE revealed that unintentional impurity incorporation into the epilayer is extremely small and precise doping effects are observable. C(sub As) acceptor-related emissions such as 'g', (g-g), and (g-g)(sub beta) are observed and their spectra are significantly changed with increasing C(+) beam current density I(sub c). PL measurements showed that C atoms were efficiently incorporated during MBE growth by CIBMBE and were optically well activated as an acceptor in the as-grown condition even for T(sub g) as low as 500 C. Raman measurement showed negligible lattice damage of the epilayer bombarded with 100 eV C(+) with no subsequent heat treatment. These results indicate that contamination- and damage-free impurity doping without postgrowth annealing can be achieved by the CIBMBE method.

Elastic electron differential cross sections for argon atom in the intermediate energy range from 40 eV to 300 eV

Science.gov (United States)

Ranković, Miloš Lj.; Maljković, Jelena B.; Tökési, Károly; Marinković, Bratislav P.

2018-02-01

Measurements and calculations for electron elastic differential cross sections (DCS) of argon atom in the energy range from 40 to 300 eV are presented. DCS have been measured in the crossed beam arrangement of the electron spectrometer with an energy resolution of 0.5 eV and angular resolution of 1.5∘ in the range of scattering angles from 20∘ to 126∘. Both angular behaviour and energy dependence of DCS are obtained in a separate sets of experiments, while the absolute scale is achieved via relative flow method, using helium as a reference gas. All data is corrected for the energy transmission function, changes of primary electron beam current and target pressure, and effective path length (volume correction). DCSs are calculated in relativistic framework by expressing the Mott's cross sections in partial wave expansion. Our results are compared with other available data.

Experimental and theoretical determinations of the absolute ionization cross section of alkali metals by electron impact in the energy range from 100 to 2000 eV

International Nuclear Information System (INIS)

Jalin, Rene

1972-01-01

The absolute electron impact ionization cross sections for the alkali metals in the energy range between 100 eV and 2000 eV were measured by the non-modulated crossed beam technique. The neutral beam of alkali atoms is produced by a Knudsen cell and crossed at right angles with the electron beam. The ions formed are collected on a plate and their intensity determined with a D.C. amplifier. The neutral beam is condensed on a cold trap cooled with liquid nitrogen, this temperature being much lower than that required to obtain total condensation. The amount of metal deposited is measured by the isotopic dilution technique and by atomic absorption, and the density of the atoms in the neutral beam is calculated. The total absolute ionization cross sections can then be determined. All possible errors have been carefully analyzed and their magnitudes estimated. The absolute ionization cross section for Li at an energy of 500 eV is: Q Li = 0,358 x 10 -16 cm 2 . This value is half of that obtained by Mac Farland and Kinney. The partial ionization cross sections for the singly and multiply charged ions is determined with a mass spectrometer attached to this apparatus. For the singly charged ions, the variation of the cross section with the energy of the ionizing electrons is in agreement with the optically allowed transition law: Q = A log BE/E. From the variation of Q with E, the squared matrix elements of the transition moment (|M i |) 2 are determined for all the elements studied. New calculations of the ionization cross section of Li and Na were performed in the framework of the Born-Bethe approximation as modified by Gaudin and Botter to take into account collisions with large momentum variation of the incident electron. Hartree-Fock type wave functions for the ground state atom (tabulated by Clementi) were used. The calculated values are in good agreement with our experimental results and with the former theoretical results calculated by various methods. This work also

Differential elastic electron scattering cross sections for CCl4 by 1.5-100 eV energy electron impact

Science.gov (United States)

Limão-Vieira, P.; Horie, M.; Kato, H.; Hoshino, M.; Blanco, F.; García, G.; Buckman, S. J.; Tanaka, H.

2011-12-01

We report absolute elastic differential, integral and momentum transfer cross sections for electron interactions with CCl4. The incident electron energy range is 1.5-100 eV, and the scattered electron angular range for the differential measurements varies from 15°-130°. The absolute scale of the differential cross section was set using the relative flow technique with helium as the reference species. Comparison with previous total cross sections shows good agreement. Atomic-like behaviour in this scattering system is shown here for the first time, and is further investigated by comparing the CCl4 elastic cross sections to recent results on the halomethanes and atomic chlorine at higher impact energies [H. Kato, T. Asahina, H. Masui, M. Hoshino, H. Tanaka, H. Cho, O. Ingólfsson, F. Blanco, G. Garcia, S. J. Buckman, and M. J. Brunger, J. Chem. Phys. 132, 074309 (2010)], 10.1063/1.3319761.

X-ray grating spectrometer for opacity measurements in the 50 eV to 250 eV spectral range at the LULI 2000 laser facility.

Science.gov (United States)

Reverdin, Charles; Thais, Frédéric; Loisel, Guillaume; Busquet, M; Bastiani-Ceccotti, S; Blenski, T; Caillaud, T; Ducret, J E; Foelsner, W; Gilles, D; Gilleron, F; Pain, J C; Poirier, M; Serres, F; Silvert, V; Soullie, G; Turck-Chieze, S; Villette, B

2012-10-01

An x-ray grating spectrometer was built in order to measure opacities in the 50 eV to 250 eV spectral range with an average spectral resolution ∼ 50. It has been used at the LULI-2000 laser facility at École Polytechnique (France) to measure the Δn = 0, n = 3 transitions of several elements with neighboring atomic number: Cr, Fe, Ni, and Cu in the same experimental conditions. Hence a spectrometer with a wide spectral range is required. This spectrometer features one line of sight looking through a heated sample at backlighter emission. It is outfitted with one toroidal condensing mirror and several flat mirrors cutting off higher energy photons. The spectral dispersion is obtained with a flatfield grating. Detection consists of a streak camera sensitive to soft x-ray radiation. Some experimental results showing the performance of this spectrometer are presented.

X-ray grating spectrometer for opacity measurements in the 50 eV to 250 eV spectral range at the LULI 2000 laser facility

International Nuclear Information System (INIS)

Reverdin, Charles; Caillaud, T.; Gilleron, F.; Pain, J. C.; Silvert, V.; Soullie, G.; Villette, B.; Thais, Frédéric; Loisel, Guillaume; Blenski, T.; Poirier, M.; Busquet, M.; Bastiani-Ceccotti, S.; Serres, F.; Ducret, J. E.; Foelsner, W.; Gilles, D.; Turck-Chieze, S.

2012-01-01

An x-ray grating spectrometer was built in order to measure opacities in the 50 eV to 250 eV spectral range with an average spectral resolution ∼ 50. It has been used at the LULI-2000 laser facility at École Polytechnique (France) to measure the Δn = 0, n = 3 transitions of several elements with neighboring atomic number: Cr, Fe, Ni, and Cu in the same experimental conditions. Hence a spectrometer with a wide spectral range is required. This spectrometer features one line of sight looking through a heated sample at backlighter emission. It is outfitted with one toroidal condensing mirror and several flat mirrors cutting off higher energy photons. The spectral dispersion is obtained with a flatfield grating. Detection consists of a streak camera sensitive to soft x-ray radiation. Some experimental results showing the performance of this spectrometer are presented.

X-ray grating spectrometer for opacity measurements in the 50 eV to 250 eV spectral range at the LULI 2000 laser facility

Energy Technology Data Exchange (ETDEWEB)

Reverdin, Charles; Caillaud, T.; Gilleron, F.; Pain, J. C.; Silvert, V.; Soullie, G.; Villette, B. [CEA, DAM, DIF, 91297 Arpajon (France); Thais, Frederic; Loisel, Guillaume; Blenski, T.; Poirier, M. [CEA, DSM, IRAMIS, Service Photons, Atomes et Molecules, 91191 Gif-sur-Yvette (France); Busquet, M. [ARTEP Inc, Ellicott City, Maryland 21042 (United States); Bastiani-Ceccotti, S.; Serres, F. [LULI, Ecole Polytechnique, CNRS, CEA, UPMC, route de Saclay, 91128 Palaiseau (France); Ducret, J. E. [CELIA, UMR5107, CEA, CNRS, Universite de Bordeaux, 33400 Talence (France); Foelsner, W. [Max Planck Instituet fuer Quantum Optik, 85748 Garching (Germany); Gilles, D.; Turck-Chieze, S. [CEA, DSM, IRFU, Service d' astrophysique, 91191 Gif-sur-Yvette (France)

2012-10-15

An x-ray grating spectrometer was built in order to measure opacities in the 50 eV to 250 eV spectral range with an average spectral resolution {approx} 50. It has been used at the LULI-2000 laser facility at Ecole Polytechnique (France) to measure the {Delta}n = 0, n = 3 transitions of several elements with neighboring atomic number: Cr, Fe, Ni, and Cu in the same experimental conditions. Hence a spectrometer with a wide spectral range is required. This spectrometer features one line of sight looking through a heated sample at backlighter emission. It is outfitted with one toroidal condensing mirror and several flat mirrors cutting off higher energy photons. The spectral dispersion is obtained with a flatfield grating. Detection consists of a streak camera sensitive to soft x-ray radiation. Some experimental results showing the performance of this spectrometer are presented.

Photon stimulated desorption investigations of positive ions of MgO, TiO2, Yb2O3, Nd2O3, H2O/Si(100), CaF2/Si and of H2O, CO and NO on Yb and Nd in the energy range 14 eV up to 800 eV

International Nuclear Information System (INIS)

Senf, F.

1987-01-01

Photon-stimulated desorption of positive ions from surfaces has been studied with synchrotron radiation in the photon energy range 14 -800 eV of the 'FLIPPER'-monochromator using a time-of-flight mass spectrometer. TiO 2 , as a prototype of a maximal valency ionic compound, shows a strong desorption of O +- in the photon energy range of the Ti 3 p → 3d- and Ti 2p → 3d-resonance as well as at the 0 1s-excitation due to intraatomic respectively intraatomic Auger decays, which is in agreement with the Knotek-Feibelman model. The desorption of F + from CaF 2 -covered silicon is found to follow the respective excitation and decay processes in Ca and F. In addition, the very large cross section for the F + desorption causes a radiation damage by photons of more than about 30 eV. The adsorbate system H 2 O/Si (100) needs a multiple electron excitation to show a significant desorption setting in only 30 eV above the 0 1s threshold. The rare earth metals Yb and Nd covered with O 2 , H 2 O, CO or NO exhibit a competitive desorption of O + partly due to intraatomic Auger decays caused by single electron excitations and partly due to multiple electron excitations. The variation of the 0 + yield with regard to the different adsorbates on Yb and Nd is unexpectedly low. A detailed investigation was concerned with thin oxidized Mg-films and differently prepared MgO-single-crystals. Here we found a very efficient desorption of O + and H + resulting from the excitation of O 1s-surface-excitons. In addition, the strong hole-hole-interaction energy of crystalline MgO appears to be responsible for a suppressed O + -signal in the energy range of the Mg 2p-excitation. (orig./BHO)

Ellipsometry and energy characterization of the electron impact polymerization in the range 0–20 eV

International Nuclear Information System (INIS)

Zyn, V.I.

2016-01-01

The electron impact polymerization of adsorbed vapors of a hydrocarbon vacuum oil with molecular mass 450 Da (C 32 H 66 ) has been studied in-situ in the range 0–20 eV using ellipsometry and a servo system with the Kelvin's vibrating probe. This allowed registering at the same time the two energy-dependent characteristics (spectra) of the process: the film growth rate and the electrical potential of the irradiated surface. The first spectrum has two resonance maxima near 2.5 and 9.5 eV while the surface potential has only one weak extremum near 9.5 eV. The first growth rate peak at 2.5 eV was connected with a creation of radicals through a resonant process of the dissociative electron attachment and beginning polymerization. The peaks at 9.5 eV in both the spectra mean accelerating polymerization and decreasing surface charge owing to simultaneous birth of highly active radicals and free electrons. The single resonant process controlling both the processes simultaneously is the dissociative attachment of an electron to an anti-bonding molecular orbital, almost the same as at the 2.5 eV but differing by deeper decomposition of the transient anion, among the products of which are now not the radicals only but also free electrons. The kinetic curves obtained in pulsed regimes of the electron bombardment were qualitatively identical for different precursors and were used for calculations of cross sections of these processes. - Highlights: • Obtaining spectra of activated polymerization using ellipsometry and Kelvin probe. • Identified: two resonant and one non-resonant mechanisms of the activation. • The resonances are due to the action of the dissociative electron attachment. • Kinetics of transient processes in adsorbed layer under 20 eV pulsed electron beam.

Photodissociation of HCN and HNC isomers in the 7-10 eV energy range

Energy Technology Data Exchange (ETDEWEB)

Chenel, Aurelie; Roncero, Octavio, E-mail: octavio.roncero@csic.es [Instituto de Física Fundamental (IFF-CSIC), C.S.I.C., Serrano 123, 28006 Madrid (Spain); Aguado, Alfredo [Departamento de Química Física Aplicada (UAM), Unidad Asociada a IFF-CSIC, Facultad de Ciencias Módulo 14, Universidad Autónoma de Madrid, 28049 Madrid (Spain); Agúndez, Marcelino; Cernicharo, José [Instituto de Ciencia de Materiales de Madrid, CSIC, C/ Sor Juana Inés de la Cruz 3, 28049 Cantoblanco (Spain)

2016-04-14

The ultraviolet photoabsorption spectra of the HCN and HNC isomers have been simulated in the 7-10 eV photon energy range. For this purpose, the three-dimensional adiabatic potential energy surfaces of the 7 lowest electronic states, and the corresponding transition dipole moments, have been calculated, at multireference configuration interaction level. The spectra are calculated with a quantum wave packet method on these adiabatic potential energy surfaces. The spectra for the 3 lower excited states, the dissociative electronic states, correspond essentially to predissociation peaks, most of them through tunneling on the same adiabatic state. The 3 higher electronic states are bound, hereafter electronic bound states, and their spectra consist of delta lines, in the adiabatic approximation. The radiative lifetime towards the ground electronic states of these bound states has been calculated, being longer than 10 ns in all cases, much longer that the characteristic predissociation lifetimes. The spectra of HCN is compared with the available experimental and previous theoretical simulations, while in the case of HNC there are no previous studies to our knowledge. The spectrum for HNC is considerably more intense than that of HCN in the 7-10 eV photon energy range, which points to a higher photodissociation rate for HNC, compared to HCN, in astrophysical environments illuminated by ultraviolet radiation.

The anisotropy of cosmic ray particles in the energy range 1011-1019 eV

International Nuclear Information System (INIS)

Xu Chunxian

1985-01-01

A study of the anisotropy of primary cosmic ray is presented. The expression of the anisotropy is derived in a model of statistical discrete sources in an infinite galaxy. Using these derived formulas, the amplitudes of the first harmonic anisotropies caused by eleven supernovea nearby the Earth are estimated individually and the trend of the resultant anisotropy is investigated. It is found that the expected results can account for the power law of Esup(0.5) of the anisotropy above the energy 5 x 10 15 eV. The Compton-getting effect can cause an additional anisotropy which is independent of energy and added to the resultant anisotropy of these discrete sources. It is apparent that the anisotropies available in the low energy range 10 11 - 10 14 eV are caused by the Compton-Getting effect. Taking the differential spectrum index γ = 2.67 measured in the same energy bound we get the streaming velocity of 35 km/s with respect to the cosmic ray background

Reflection of 32--2000 eV deuterium from carbon

International Nuclear Information System (INIS)

Braun, M.; Thomas, E.W.

1982-01-01

Reflection of deuterium from carbon is measured by a technique based on the rise of partial pressure caused by the reflected particles. Data are presented for 32--2000 eV per deuteron incident energies and as a function of angle of incidence. The data are consistent with previous determinations at energies above 1000 eV. A systematic difference in energy dependence is found when the measurements for reflection of deuterium are compared on a reduced energy scale with MARLOWE computer simulations of hydrogen reflection

VUV action spectroscopy of protonated leucine-enkephalin peptide in the 6-14 eV range

Energy Technology Data Exchange (ETDEWEB)

Ranković, M. Lj. [Institute of Physics Belgrade, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia); Canon, F. [INRA, UMR1324 Centre des Sciences du Goût et de l’Alimentation, F-21000 Dijon (France); Nahon, L. [SOLEIL, l’Orme des Merisiers, St Aubin, BP48, 91192 Gif sur Yvette Cedex (France); Giuliani, A. [SOLEIL, l’Orme des Merisiers, St Aubin, BP48, 91192 Gif sur Yvette Cedex (France); INRA, UAR1008, CEPIA, Rue de la Géraudière, BP 71627, 44316 Nantes (France); Milosavljević, A. R., E-mail: vraz@ipb.ac.rs [Institute of Physics Belgrade, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia); Radiation Laboratory, University of Notre Dame, Notre Dame, Indiana 46556 (United States)

2015-12-28

We have studied the Vacuum Ultraviolet (VUV) photodissociation of gas-phase protonated leucine-enkephalin peptide ion in the 5.7 to 14 eV photon energy range by coupling a linear quadrupole ion trap with a synchrotron radiation source. We report VUV activation tandem mass spectra at 6.7, 8.4, and 12.8 eV photon energies and photodissociation yields for a number of selected fragments. The obtained results provide insight into both near VUV radiation damage and electronic properties of a model peptide. We could distinguish several absorption bands and assign them to particular electronic transitions, according to previous theoretical studies. The photodissociation yields appear to be very different for the various observed fragmentation channels, depending on both the types of fragments and their position along the peptide backbone. The present results are discussed in light of recent gas-phase spectroscopic data on peptides.

Europium resonance parameters from neutron capture and transmission measurements in the energy range 0.01–200 eV

International Nuclear Information System (INIS)

Leinweber, G.; Barry, D.P.; Burke, J.A.; Rapp, M.J.; Block, R.C.; Danon, Y.; Geuther, J.A.; Saglime III, F.J.

2014-01-01

Highlights: • Metal samples were sealed and imaged with X-rays to determine sample uniformity. • Eleven new resonances were identified below 100 eV. • The resonance regions of 151 Eu and 153 Eu have been extended from 100 to 200 eV. • The thermal total cross section for 151 Eu was measured, up (9 ± 3)% from ENDF/B-VII.1. • Radiation widths were assigned for all resonances from experimental data. - Abstract: Europium is a good absorber of neutrons suitable for use as a nuclear reactor control material. It is also a fission product in the low-yield tail at the high end of the fission fragment mass distribution. Measurements have been made of the stable isotopes with natural and enriched samples. The linear electron accelerator center (LINAC) at the Rensselaer Polytechnic Institute (RPI) was used to explore neutron interactions with europium in the energy region from 0.01 to 200 eV. Neutron capture and transmission measurements were performed by the time-of-flight technique. Two transmission measurements were performed at flight paths of 15 and 25 m with 6 Li glass scintillation detectors. The neutron capture measurements were performed at a flight path of 25 m with a 16-segment sodium iodide multiplicity detector. Resonance parameters were extracted from the data using the multilevel R-matrix Bayesian code SAMMY. A table of resonance parameters and their uncertainties is presented. To prevent air oxidation metal samples were sealed in airtight aluminum cans in an inert environment. Metal samples of natural europium, 47.8 atom% 151 Eu, 52.2 atom% 153 Eu, as well as metal samples enriched to 98.77 atom% 153 Eu were measured. The measured neutron capture resonance integral for 153 Eu is (9.9 ± 0.4)% larger than ENDF/B-VII.1. The capture resonance integral for 151 Eu is (7 ± 1)% larger than ENDF/B-VII.1. Another significant finding from these measurements was a significant increase in thermal total cross section for 151 Eu, up (9 ± 3)% from ENDF/B-VII.1

EV range sensitivity analysis

Energy Technology Data Exchange (ETDEWEB)

Ostafew, C. [Azure Dynamics Corp., Toronto, ON (Canada)

2010-07-01

This presentation included a sensitivity analysis of electric vehicle components on overall efficiency. The presentation provided an overview of drive cycles and discussed the major contributors to range in terms of rolling resistance; aerodynamic drag; motor efficiency; and vehicle mass. Drive cycles that were presented included: New York City Cycle (NYCC); urban dynamometer drive cycle; and US06. A summary of the findings were presented for each of the major contributors. Rolling resistance was found to have a balanced effect on each drive cycle and proportional to range. In terms of aerodynamic drive, there was a large effect on US06 range. A large effect was also found on NYCC range in terms of motor efficiency and vehicle mass. figs.

Hyperthermal (1-100 eV) nitrogen ion scattering damage to D-ribose and 2-deoxy-D-ribose films.

Science.gov (United States)

Deng, Zongwu; Bald, Ilko; Illenberger, Eugen; Huels, Michael A

2007-10-14

Highly charged heavy ion traversal of a biological medium can produce energetic secondary fragment ions. These fragment ions can in turn cause collisional and reactive scattering damage to DNA. Here we report hyperthermal (1-100 eV) scattering of one such fragment ion (N(+)) from biologically relevant sugar molecules D-ribose and 2-deoxy-D-ribose condensed on polycrystalline Pt substrate. The results indicate that N(+) ion scattering at kinetic energies down to 10 eV induces effective decomposition of both sugar molecules and leads to the desorption of abundant cation and anion fragments. Use of isotope-labeled molecules (5-(13)C D-ribose and 1-D D-ribose) partly reveals some site specificity of the fragment origin. Several scattering reactions are also observed. Both ionic and neutral nitrogen atoms abstract carbon from the molecules to form CN(-) anion at energies down to approximately 5 eV. N(+) ions also abstract hydrogen from hydroxyl groups of the molecules to form NH(-) and NH(2) (-) anions. A fraction of OO(-) fragments abstract hydrogen to form OH(-). The formation of H(3)O(+) ions also involves hydrogen abstraction as well as intramolecular proton transfer. These findings suggest a variety of severe damaging pathways to DNA molecules which occur on the picosecond time scale following heavy ion irradiation of a cell, and prior to the late diffusion-limited homogeneous chemical processes.

Total absorption and photoionization cross sections of water vapor between 100 and 1000 A

Science.gov (United States)

Haddad, G. N.; Samson, J. A. R.

1986-01-01

Absolute photoabsorption and photoionization cross sections of water vapor are reported at a large number of discrete wavelengths between 100 and 1000 A with an estimate error of + or - 3 percent in regions free from any discrete structure. The double ionization chamber technique utilized is described. Recent calculations are shown to be in reasonable agreement with the present data.

Performance of a 100V Half-Bridge MOSFET Driver, Type MIC4103, Over a Wide Temperature Range

Science.gov (United States)

Patterson, Richard L.; Hammoud, Ahmad

2011-01-01

The operation of a high frequency, high voltage MOSFET (metal-oxide semiconductor field-effect transistors) driver was investigated over a wide temperature regime that extended beyond its specified range. The Micrel MIC4103 is a 100V, non-inverting, dual driver that is designed to independently drive both high-side and low-side N-channel MOSFETs. It features fast propagation delay times and can drive 1000 pF load with 10ns rise times and 6 ns fall times [1]. The device consumes very little power, has supply under-voltage protection, and is rated for a -40 C to +125 C junction temperature range. The floating high-side driver of the chip can sustain boost voltages up to 100 V. Table I shows some of the device manufacturer s specification.

VUV photoionization of acetamide studied by electron/ion coincidence spectroscopy in the 8–24 eV photon energy range

International Nuclear Information System (INIS)

Schwell, Martin; Bénilan, Yves; Fray, Nicolas; Gazeau, Marie-Claire; Es-Sebbar, Et.; Garcia, Gustavo A.; Nahon, Laurent; Champion, Norbert; Leach, Sydney

2012-01-01

Highlights: ► We study the VUV photoionization of acetamide in the 8–24 eV photon energy range. ► Electron/ion coincidence measurements are performed using synchrotron radiation. ► The adiabatic ionization energy of acetamide is determined by TPEPICO measurements. ► VUV induced fragmentation pathways of acetamide are assigned and discussed. - Abstract: A VUV photoionization study of acetamide was carried out over the 8–24 eV photon energy range using synchrotron radiation and photoelectron/photoion coincidence (PEPICO) spectroscopy. Threshold photoelectron photoion coincidence (TPEPICO) measurements were also made. Photoion yield curves and branching ratios were measured for the parent ion and six fragment ions. The adiabatic ionization energy of acetamide was determined as I.E. (1 2 A′) = (9.71 ± 0.02) eV, in agreement with an earlier reported photoionization mass spectrometry (PIMS) value. The adiabatic energy of the first excited state of the ion, 1 2 A″, was determined to be ≈10.1 eV. Assignments of the fragment ions and the pathways of their formation by dissociative photoionization were made. The neutral species lost in the principal dissociative photoionization processes are CH 3 , NH 2 , NH 3 , CO, HCCO and NH 2 CO. Heats of formation are derived for all ions detected and are compared with literature values. Some astrophysical implications of these results are discussed.

Temperature dependence of the dielectric tensor of monoclinic Ga2O3 single crystals in the spectral range 1.0-8.5 eV

Science.gov (United States)

Sturm, C.; Schmidt-Grund, R.; Zviagin, V.; Grundmann, M.

2017-08-01

The full dielectric tensor of monoclinic Ga2O3 (β-phase) was determined by generalized spectroscopic ellipsometry in the spectral range from 1.0 eV up to 8.5 eV and temperatures in the range from 10 K up to 300 K. By using the oriented dipole approach, the energies and broadenings of the excitonic transitions are determined as a function of the temperature, and the exciton-phonon coupling properties are deduced.

Strategy for 100-year life of the ACR-1000 concrete containment structure

International Nuclear Information System (INIS)

Abrishami, H.; Elgohary, M.

2006-01-01

The purpose of this paper is to present the Plant Life Management (PLiM) strategy for the concrete containment structure of the ACR-1000 (Advanced CANDU Reactor) designed by AECL. The ACR-1000 is designed for 100-year plant life including 60-year operating life and additional 40-year decommissioning period of time. The approach adopted for the PLiM strategy of the concrete containment structure is a preventive one, key areas being: 1) design methodology, 2) material performance and 3) life cycle management and ageing management program. In the design phase, in addition to strength and serviceability, durability is a major requirement during the service life and decommissioning phase of the ACR structure. Parameters affecting durability design include: a) concrete performance, b) structural application, and c) environmental conditions. Due to the complex nature of the environmental effects acting on structures during the service life of project, it is considered that true improved performance during the service life can be achieved by improving the material characteristics. Many recent innovations in advanced concrete materials technology have made it possible to produce modern concrete such as high-performance concrete with exceptional performance characteristics. In this paper, the PLiM strategy for the ACR-1000 concrete containment is presented. In addition to addressing the design methodology and material performance areas, a systematic approach for ageing management program for the concrete containment structure is presented. (author)

Longitudinal Changes in Young Children’s 0-100 to 0-1000 Number-Line Error Signatures

Directory of Open Access Journals (Sweden)

Robert A. Reeve

2015-05-01

Full Text Available We use a latent difference score (LDS model to examine changes in young children’s number-line (NL error signatures (errors marking numbers on a NL over 18 months. A LDS model (1 overcomes some of the inference limitations of analytic models used in previous research, and in particular (2 provides a more reliable test of hypotheses about the meaning and significance of changes in NL error signatures over time and task. The NL error signatures of 217 6-year-olds’ (on test occasion one were assessed three times over 18 months, along with their math ability on two occasions. On the first occasion (T1 children completed a 0–100 NL task; on the second (T2 a 0–100 NL and a 0–1000 NL task; on the third (T3 occasion a 0–1000 NL task. On the third and fourth occasions (T3 and T4, children completed mental calculation tasks. Although NL error signatures changed over time, these were predictable from other NL task error signatures, and predicted calculation accuracy at T3, as well as changes in calculation between T3 and T4. Multiple indirect effects (change parameters showed that associations between initial NL error signatures (0–100 NL and later mental calculation ability were mediated by error signatures on the 0–1000 NL task. The pattern of findings from the LDS model highlight the value of identifying direct and indirect effects in characterizing changing relationships in cognitive representations over task and time. Substantively, they support the claim that children’s NL error signatures generalize over task and time and thus can be used to predict math ability.

Graphs of neutron cross sections in JSD1000 for radiation shielding safety analysis

International Nuclear Information System (INIS)

Yamano, Naoki

1984-03-01

Graphs of neutron cross sections and self-shielding factors in the JSD1000 library are presented for radiation shielding safety analysis. The compilation contains various reaction cross sections for 42 nuclides from 1 H to 241 Am in the energy range from 3.51 x 10 -4 eV to 16.5 MeV. The Bondarenko-type self-shielding factors of each reaction are given by the background cross sections from σ 0 = 0 to σ 0 = 10000. (author)

Identification of specific antigenic epitope at N-terminal segment of enterovirus 71 (EV-71) VP1 protein and characterization of its use in recombinant form for early diagnosis of EV-71 infection.

Science.gov (United States)

Zhang, Jianhua; Jiang, Bingfu; Xu, Mingjie; Dai, Xing; Purdy, Michael A; Meng, Jihong

2014-08-30

Human enterovirus 71 (EV-71) is the main etiologic agent of hand, foot and mouth disease (HFMD). We sought to identify EV-71 specific antigens and develop serologic assays for acute-phase EV-71 infection. A series of truncated proteins within the N-terminal 100 amino acids (aa) of EV-71 VP1 was expressed in Escherichia coli. Western blot (WB) analysis showed that positions around 11-21 aa contain EV-71-specific antigenic sites, whereas positions 1-5 and 51-100 contain epitopes shared with human coxsackievirus A16 (CV-A16) and human echovirus 6 (E-6). The N-terminal truncated protein of VP1, VP₁₆₋₄₃, exhibited good stability and was recognized by anti-EV-71 specific rabbit sera. Alignment analysis showed that VP₁₆₋₄₃ is highly conserved among EV-71 strains from different genotypes but was heterologous among other enteroviruses. When the GST-VP₁₆₋₄₃ fusion protein was incorporated as antibody-capture agent in a WB assay and an ELISA for detecting anti-EV-71 IgM in human sera, sensitivities of 91.7% and 77.8% were achieved, respectively, with 100% specificity for both. The characterized EV-71 VP1 protein truncated to positions 6-43 aa has potential as an antigen for detection of anti-EV-71 IgM for early diagnosis of EV-71 infection in a WB format. Copyright © 2014 Elsevier B.V. All rights reserved.

How Do The EV Project Participants Feel About Charging Their EV Away From Home?

Energy Technology Data Exchange (ETDEWEB)

Francfort, James E. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-02-01

The EV Project is an infrastructure study that enrolled over 8,000 residential participants. These participants purchased or leased a Nissan Leaf battery electric vehicle or Chevrolet Volt extended-range electric vehicle and were among the first to explore this new electric drive technology. Collectively, battery electric vehicles, extended-range electric vehicles, and plug-in hybrid electric vehicles are called PEVs. The EV Project participants were very cooperative and enthusiastic about their participation in the project and very supportive in providing feedback and information. The information and attitudes of these participants concerning their experience with their PEVs were solicited using a survey in June 2013. At that time, some had up to 3 years of experience with their PEVs.

Level excitation cross sections of Si I fragments produced by 100 eV electron impact on SiH4

International Nuclear Information System (INIS)

Sato, T.; Kono, A.; Goto, T.

1988-01-01

The fluorescence decay Si I atomic lines after electron impact excitation of SiH 4 molecular gas was observed, and the level excitation cross sections (LECS) of Si I fragments were determined by separating the contribution from cascade transitions to line emissions. Observed transitions were 4s 1 P--3p 2 1 D, 4s 3 P--3p 2 3 P, 3d 1 P--3p 2 1 S, 3d 1 D--3p 2 1 D, 3d 1 F--3p 2 1 D, 3d 3 P--3p 2 3 P, and 3p 3 3 D--3p 2 3 P, for which the LECSs of the upper levels were determined at 100 eV excitation energy. The contribution of the direct excitations to these line emissions were found to range from 37% to 80%. Analysis of the 4s 1 P--3p 2 1 D decay curve also gave the LECSs of the cascading levels 4p 1 P, 4p 1 S, and 4p 1 D. Also obtained were some radiative lifetimes not reported before

How Do The EV Project Participants Feel About Their EVS?

Energy Technology Data Exchange (ETDEWEB)

Francfort, James E. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-02-01

The EV Project is an infrastructure study that enrolled over 8,000 residential participants. These participants purchased or leased a Nissan Leaf battery electric vehicle (BEV) or Chevrolet Volt extended range electric vehicle (EREV) and were among the first to explore this new electric drive technology. Collectively, BEV, EREV, and plug-in hybrid electric vehicles (PHEVs) are called plug-in electric vehicles (PEVs). The EV Project participants were very cooperative and enthusiastic about their participation in the project and very supportive in providing feedback and information. The information and attitudes of these participants concerning their experience with their PEVs were solicited using a survey in June 2013. At that time, some had up to 3 years of experience with their PEVs.

Observation of γ rays > 1015 eV from Cygnus X-3

International Nuclear Information System (INIS)

Lloyd-Evans, J.; Coy, R.N.; Lambert, A.; Lapikens, J.; Patel, M.; Reid, R.J.O.; Watson, A.A.

1983-01-01

The X-ray binary system Cygnus X-3 is a source of particular interest. As well as emitting X-rays which are modulated with a 4.8-h period, it has been observed in 30-100 MeV γ rays by the SAS II satellite and several groups have detected γ rays in the TeV range showing the same period. Most recently, using the small extensive air shower array at Kiel, workers have found that the γ-ray spectrum of Cygnus X-3 extends above 2 x 10 15 eV, with an integral flux of (7.4 +- 3.2) x 10 -14 cm -2 s -1 . This paper confirms the Kiel observations and presents evidence that the γ-ray spectrum of Cygnus X-3 steepens above 10 16 eV. (author)

VUV photoionization of acetamide studied by electron/ion coincidence spectroscopy in the 8-24 eV photon energy range

KAUST Repository

Schwell, Martin; Bé nilan, Yves; Fray, Nicolas; Gazeau, Marie Claire; Es-sebbar, Et-touhami; Garcí a, Gustavo A.; Nahon, Laurent; Champion, Norbert; Leach, Sydney Sydney

2012-01-01

A VUV photoionization study of acetamide was carried out over the 8-24 eV photon energy range using synchrotron radiation and photoelectron/photoion coincidence (PEPICO) spectroscopy. Threshold photoelectron photoion coincidence (TPEPICO) measurements were also made. Photoion yield curves and branching ratios were measured for the parent ion and six fragment ions. The adiabatic ionization energy of acetamide was determined as I.E. (1 2A′) = (9.71 ± 0.02) eV, in agreement with an earlier reported photoionization mass spectrometry (PIMS) value. The adiabatic energy of the first excited state of the ion, 1 2A″, was determined to be ≈10.1 eV. Assignments of the fragment ions and the pathways of their formation by dissociative photoionization were made. The neutral species lost in the principal dissociative photoionization processes are CH 3, NH 2, NH 3, CO, HCCO and NH 2CO. Heats of formation are derived for all ions detected and are compared with literature values. Some astrophysical implications of these results are discussed. © 2011 Elsevier B.V. All rights reserved.

Modeling of Electric Vehicles (EVs) for EV Grid Integration Study

DEFF Research Database (Denmark)

Wu, Qiuwei; Nielsen, Arne Hejde; Østergaard, Jacob

2010-01-01

In order to successfully integrate EVs into power systems, it is necessary to develop a detailed EV model considering both the EV users’ driving requirements and the battery charging and discharging characteristics. A generic EV model was proposed which takes into account charging and discharging...... characteristics of EV batteries, the driving distance per trip and the availability of EVs for charging and providing grid service. The charging and discharging characteristics of EV batteries were used to determine the upper and lower limits of the state of charge (SOC) of EV batteries and to calculate...... the charging and discharging power. The driving distance per trip and availability of EVs were used to reflect the driving requirements and to implement intelligent charging and discharging management....

Temperature dependence of photoconductivity at 0.7 eV in single-wall carbon nanotube films

Directory of Open Access Journals (Sweden)

Yukitaka Matsuoka, Akihiko Fujiwara, Naoki Ogawa, Kenjiro Miyano, Hiromichi Kataura, Yutaka Maniwa, Shinzo Suzuki and Yohji Achiba

2003-01-01

Full Text Available Temperature dependence of photoconductivity has been investigated for single-wall carbon nanotube films at 0.7 eV. In order to clarify the effect of atmosphere on photoconductivity, measurements have been performed under helium and nitrogen gas flow in the temperature range from 10 K to room temperature (RT and from 100 K to RT, respectively. Photoconductive response monotonously increases with a decrease in temperature and tends to saturate around 10 K. No clear difference in photoconductive response under different atmosphere was observed. We discuss the mechanism of photoconductivity at 0.7 eV.

An ultrahigh-vacuum apparatus for resonant diffraction experiments using soft x rays (hν=300-2000 eV)

International Nuclear Information System (INIS)

Takeuchi, T.; Chainani, A.; Takata, Y.; Tanaka, Y.; Oura, M.; Tsubota, M.; Senba, Y.; Ohashi, H.; Mochiku, T.; Hirata, K.; Shin, S.

2009-01-01

We have developed an ultrahigh-vacuum instrument for resonant diffraction experiments using polarized soft x rays in the energy range of hν=300-2000 eV at beamline BL17SU of SPring-8. The diffractometer consists of modified differentially pumped rotary feedthroughs for θ-2θ stages, a sample manipulator with motor-controlled x-y-z-, tilt (χ)-, and azimuth (φ)-axes, and a liquid helium flow-type cryostat for temperature dependent measurements between 30 and 300 K. Test results indicate that the diffractometer exhibits high reproducibility (better than 0.001 deg.) for a Bragg reflection of α-quartz 100 at a photon energy of hν=1950 eV. Typical off- and on-resonance Bragg reflections in the energy range of 530-1950 eV could be measured using the apparatus. The results show that x-ray diffraction experiments with energy-, azimuth-, and incident photon polarization-dependence can be reliably measured using soft x rays in the energy range of ∼300-2000 eV. The facility can be used for resonant diffraction experiments across the L-edge of transition metals, M-edge of lanthanides, and up to the Si K-edge of materials.

Radiation hardening lacquer binding agent based on a polyester resin with at least 3.5 double links pr. 1000 molecular weight units

International Nuclear Information System (INIS)

Crimlisk, D.J.; Wright, A.; Groves, T.E.

1976-01-01

The binding agent is suitable for hardening by electrons with an energy of between 100,000 and 500,000eV. It consists mainly of a solution of a polyester resin with at least 3.5 double links per 1000 mol, in an olefine-unsaturated monomer. The molecular weight of the polyester is between 800 and 1100 and the ratio of the number of double links in the monomer to that in the resin (degree of unsaturation) is in the range 0.75-2.0, or more specifically, between 1 and 1.5. Cellulose acetate/butyrate (CAB) and/or a butylated melamine/formaldehyde resin may be added to improve the surface properties. Likewise from 0.1 to 0.5% polyethylene wax may be added to give a better surface finish and hardness. (JIW)

Dielectric tensor of monoclinic Ga2O3 single crystals in the spectral range 0.5–8.5 eV

Directory of Open Access Journals (Sweden)

C. Sturm

2015-10-01

Full Text Available The dielectric tensor of Ga2O3 in the monoclinic (β phase was determined by generalized spectroscopic ellipsometry in a wide spectral range from 0.5 eV to 8.5 eV as well as by density functional theory calculations combined with many-body perturbation theory including quasiparticle and excitonic effects. The dielectric tensors obtained by both methods are in excellent agreement with each other and the observed transitions in the dielectric function are assigned to the corresponding valence bands. It is shown that the off-diagonal element of the dielectric tensor reaches values up to |εxz| ≈ 0.30 and cannot be neglected. Even in the transparent spectral range where it is quite small (|εxz| < 0.02 it causes a rotation of the dielectric axes around the symmetry axis of up to 20°.

Design and characterization for absolute x-ray spectrometry in the 100-10,000 eV region

International Nuclear Information System (INIS)

Henke, B.L.

1986-08-01

Reviewed here are the design and characterization procedures used in our program for developing absolute x-ray spectrometry in the 100 to 10,000 eV region. Described are the selection and experimental calibration of the x-ray filters, mirror momochromators, crystal/multilayer analyzers, and the photographic (time integrating) and photoelectric (time resolving) position-sensitive detectors. Analytical response functions have been derived that characterize the energy dependence of the mirror and crystal/multilayer reflectivities and of the photographic film and photocathode sensitivities. These response functions permit rapid, small-computer reduction of the experimental spectra to absolute spectra (measured in photons per stearadian from the source for radiative transitions at indicated photon energies). Our x-ray spectrographic systems are being applied to the diagnostics of pulsed, high temperature plasma sources in laser fusion and x-ray laser research. 15 refs., 27 figs

Hyperthermal (10-500 eV) collisions of noble gases with Ni(100) surface. Comparison between light and heavy atom collisions

International Nuclear Information System (INIS)

Kim, C.

1995-01-01

Collisional events between 10-500 eV atomic beams (He, Ne, Ar, Kr, and Xe) and a Ni(100) surface are investigated by the classical trajectory method. The calculation employs a molecular dynamics approach combined with a Langevin method for treating energy dissipation to infinite solid. We find that low energy collisions of heavy atoms (Xe and Kr) are characterized by extensive many-body interactions with top layer surface atoms. On the other hand, light atom (Ne and He) collisions can be approximated as a sequence of binary collisions even at these energies. Such a difference in the collisional nature gives rise to the following consequences. Low energy heavy atoms transfer energy mostly to the surface atoms during 45 angle collision. They scatter from the surface with a narrow angular distribution centered in a supraspecular direction. The ratio of the scattered to incident particle energy rapidly decreases with increasing beam energy of heavy atoms. The sputtering yield for Ni atoms by heavy atom bombardment increases quite linearly with beam energy, which is attributed to a linear proportionality between the beam energy and the energy transfered to a surface. Near the threshold energy sputtering can occur more efficiently by light atom bombardment. The energy transfer ratio to solid continuously increases with beam energy for light atoms. For heavy projectiles, on the other hand, this ratio reaches a maximum at the energy of ca, 100 eV, above which it stays nearly constant but slightly decreases. ((orig.))

NANO-BATTERY TECHNOLOGY FOR EV-HEV PANEL: A PIONEERING STUDY

Directory of Open Access Journals (Sweden)

Ataur Rahman

2015-11-01

Full Text Available Global trends toward CO2 reduction and resource efficiency have significantly increased the importance of lightweight materials for automobile original equipment manufacturers (OEM. CO2 reduction is a fundamental driver for a more lightweight automobile. The introduction of Electrical Vehicles (EVs is one initiative towards this end. However EVs are currently facing several weaknesses: limited driving range, battery pack heaviness, lack of safety and thermal control, high cost, and overall limited efficiency. This study presents a panel-style nano-battery technology built into an EV with CuO filler solid polymer electrolyte (SPE sandwiched by carbon fiber (CF and lithium (Li plate. In addition to this, an aluminum laminated polypropylene film is used as the electromagnetic compatibility (EMC shield. The proposed battery body panel of the EV would reduce the car weight by about 20%, with a charge and discharge capacity of 1.5 kWh (10% of car total power requirement, and provide the heat insulation for the car which would save about 10% power consumption of the air conditioning system. Therefore, the EV would be benefited by 30% in terms of energy reduction by using the proposed body. Furthermore, the proposed body is considered environmental-friendly since it is recyclable for use in a new product. However, the main limiting factors of the SPE are its thermal behavior and moderate ionic conductivity at low temperatures. The SPE temperature is maintained by controlling the battery panel charging/discharge rate. It is expected that the proposed panel-style nano-battery use in an EV would save up to 6.00 kWh in battery energy, equivalent to 2.81 liters of petrol and prevent 3.081 kg of CO2 emission for a travel distance of 100 km. KEYWORDS: epoxy resin; carbon fiber; lithium thin plate; energy generation; solid electrolyte battery

Optical constants of silicon monocrystals in the range of 70-400 eV

International Nuclear Information System (INIS)

Filatova, E.O.; Vinogradov, A.S.; Sorokin, I.A.; Zimkina, T.M.

1983-01-01

Optical constants (refractive index n and the linear absorption coefficient μ) of monocrystalline silicon in the quantum energy range of 70-400 eV are calculated from experimental reflection spectra using the dispersion Kramers-Kronig correlation. It is found that the general type of spectral dependences μ and n in the number of details of the structure and their energetic position depends but weakty on the fact which of the reflection spectra (4, 8 or 12 deg) is used in the calculation. A noticeable increase of calculated absorption coefficients μ in the case of increasing sliding drop angle from 4 to 12 deg is connected with the growth of the depth of radiation penetration in silicon and the corresponding increase of the medium density of the substance in the reflecting near-surface layer. When comparing the absorption spectra the identity of the fine structure and the presence of great differences in the intensity of structure details is observed. Possible reasons for such discrepancy are analyzed. A range of anomalous dispersion of the refractive index is shown to exist in the region of Lsub(2, 3) -edge of absorption (n > 1)

Fission cross section of 245Cm from 10-3 eV to 104 eV

International Nuclear Information System (INIS)

White, R.M.; Browne, J.C.; Howe, R.E.; Landrum, J.H.; Becker, J.A.

1979-01-01

The neutron-induced fission cross section of 245 Cm measured from .001 eV to 10 keV using the LLL 100-MeV Linac. The resonance data are analyzed with a multilevel-multichannel R-matrix code. The statistical distribution of R-matrix parameters extracted from the analysis are investigated and comparisons are made with previous work. 4 reference

Metabolomics of Small Numbers of Cells: Metabolomic Profiling of 100, 1000, and 10000 Human Breast Cancer Cells.

Science.gov (United States)

Luo, Xian; Li, Liang

2017-11-07

In cellular metabolomics, it is desirable to carry out metabolomic profiling using a small number of cells in order to save time and cost. In some applications (e.g., working with circulating tumor cells in blood), only a limited number of cells are available for analysis. In this report, we describe a method based on high-performance chemical isotope labeling (CIL) nanoflow liquid chromatography mass spectrometry (nanoLC-MS) for high-coverage metabolomic analysis of small numbers of cells (i.e., ≤10000 cells). As an example, 12 C-/ 13 C-dansyl labeling of the metabolites in lysates of 100, 1000, and 10000 MCF-7 breast cancer cells was carried out using a new labeling protocol tailored to handle small amounts of metabolites. Chemical-vapor-assisted ionization in a captivespray interface was optimized for improving metabolite ionization and increasing robustness of nanoLC-MS. Compared to microflow LC-MS, the nanoflow system provided much improved metabolite detectability with a significantly reduced sample amount required for analysis. Experimental duplicate analyses of biological triplicates resulted in the detection of 1620 ± 148, 2091 ± 89 and 2402 ± 80 (n = 6) peak pairs or metabolites in the amine/phenol submetabolome from the 12 C-/ 13 C-dansyl labeled lysates of 100, 1000, and 10000 cells, respectively. About 63-69% of these peak pairs could be either identified using dansyl labeled standard library or mass-matched to chemical structures in human metabolome databases. We envisage the routine applications of this method for high-coverage quantitative cellular metabolomics using a starting material of 10000 cells. Even for analyzing 100 or 1000 cells, although the metabolomic coverage is reduced from the maximal coverage, this method can still detect thousands of metabolites, allowing the analysis of a large fraction of the metabolome and focused analysis of the detectable metabolites.

Protective effect of enterovirus‑71 (EV71) virus‑like particle vaccine against lethal EV71 infection in a neonatal mouse model.

Science.gov (United States)

Cao, Lei; Mao, Fengfeng; Pang, Zheng; Yi, Yao; Qiu, Feng; Tian, Ruiguang; Meng, Qingling; Jia, Zhiyuan; Bi, Shengli

2015-08-01

Enterovirus-71 (EV71) is a viral pathogen that causes severe cases of hand, foot and mouth disease (HFMD) among young children, with significant mortality. Effective vaccines against HFMD are urgently required. Several EV71 virus-like particle (VLP) vaccine candidates were found to be protective in the neonatal mouse EV71 challenge model. However, to what extent the VLP vaccine protects susceptible organs against EV71 infection in vivo has remained elusive. In the present study, the comprehensive immunogenicity of a potential EV71 vaccine candidate based on VLPs was evaluated in a neonatal mouse model. Despite lower levels of neutralizing antibodies to EV71 in the sera of VLP-immunized mice compared with those in mice vaccinated with inactivated EV71, the VLP-based vaccine was shown to be able to induce immunoglobulin (Ig)G and IgA memory-associated cellular immune responses to EV71. Of note, the EV71 VLP vaccine candidate was capable of inhibiting viral proliferation in cardiac muscle, skeletal muscle, lung and intestine of immunized mice and provided effective protection against the pathological damage caused by viral attack. In particular, the VLP vaccine was able to inhibit the transportation of EV71 from the central nervous system to the muscle tissue and greatly protected muscle tissue from infection, along with recovery from the viral infection. This led to nearly 100% immunoprotective efficacy, enabling neonatal mice delivered by VLP-immunized female adult mice to survive and grow with good health. The present study provided valuable additional knowledge of the specific protective efficacy of the EV71 VLP vaccine in vivo, which also indicated that it is a promising potential candidate for being developed into an EV71 vaccine.

Total neutron cross sections of berkelium-249 and californium-249 below 100 eV

International Nuclear Information System (INIS)

Benjamin, R.W.; Harvey, J.A.; Hill, N.W.; Pandey, M.S.; Carlton, R.F.

1979-01-01

The neutron total cross sections of 249 Bk and 249 Cf have been measured from 0.03 to 100 eV using the Oak Ridge Electron Linear Accelerator (ORELA) as a source of pulsed neutrons. The 1.6 mm dia. cylindrical transmission samples contained initially up to 5.3 mg of 98% 249 Bk and 2% 249 Cf: 4.5 years later, when the final measurements were made, the composition of the samples had become 2.5% 249 Bk, 96.9% 249 Cf, and 0.6% 245 Cm. Samples were cooled with liquid nitrogen to reduce Doppler broadening. Thirty-nine resonances were identified in 249 Bk and analyzed using a single-level Breit-Wigner formalism. Fifty-five resonances were identified in 249 Cf and analyzed using an R-matrix multilevel formalism. Fifty-five resonances were identified in 249 Cf and analyzed using an R-matrix multilevel formalism. The resonance parameters obtained have been used to determine the average level spacings and the s-wave neutron and fission strength functions. Where possible, bound-level parameters were derived to fit the thermal neutron total cross section data

Germanium thermometers in the temperature range .1000K to 4.20K

International Nuclear Information System (INIS)

Hsieh, S.Y.; Sanchez, D.H.

1974-01-01

The sensitivity characteristics of two germanium thermometers that proved to be convenient sensors in the temperature range from .100 0 K to 4.2 0 K, are described. Their resistances change from about 8 x 10 5 ohms at .100 0 K to about 100 ohms at 4.2 0 K. The calibration curves were fitted to natural spline functions of order 3 in the whole range of temperatures. These functions give less than half millidegree standard dispersion against 15 millidegree standard dispersion when usual polynomial interpolations are used. It is discussed what spline functions are, and compare the goodness of spline interpolation with polynomial methods [pt

Measurement of positron reemission from thin single-crystal W(100) films

International Nuclear Information System (INIS)

Chen, D.M.; Lynn, K.G.; Pareja, R.; Nielsen, B.

1985-01-01

Epitaxial thin single-crystal (100) tungsten films 1000, 2500, and 5000 A thick have been fabricated by high-vacuum electron-beam evaporation. These films were subsequently used as thin-film moderators for the study of the positron-transmission-reemission process with a variable-energy (0--80 keV) monoenergetic positron beam in an ultrahigh-vacuum system. The films were shown to be routinely cleanable by heating first in oxygen (10 -6 Torr) and then in vacuum (10 -9 Torr). Transmission and back reemission of slow positrons from these surfaces was observed. The positron work function, phi/sub +/ has been determined to be approx. =3.0 eV ( +- 0.3 eV). The transmission slow positrons were emitted in a narrow cone with a full width at half maximum of approx. =30 0 consistent with the angular distribution of back-reemission positrons. The reemitted yields as a function of incident positron energy were found to be very different between forward reemission and back reemission. The maximum forward-reemission yields were 18% for 1000-A-thick W film and 12% for 2500-A-thick W film at 5 and 10 keV optimum incident positron energies, respectively. These results show that one can use thin single-crystal tungsten films as positron moderators or remoderators

SITHA program for simulating hadron transport in the 100-1010eV energy range. Simulation of neutron transport with E6 eV

International Nuclear Information System (INIS)

Daniehl', A.V.; Dushin, V.N.

1987-01-01

The methods for simulation of neutron transport with Z<20 MeV used in the SITHA (simulation transport hadron) program, the original library of group microconstants (175 groups) with subgroup description of resonance range and a set of programs for its creation are described. The results of a number of integral experiments are discussed

P sub(T)-flow in 100 - 1000 TeV

International Nuclear Information System (INIS)

Amato, N.M.; Arata, N.; Maldonado, R.H.C.

1983-01-01

It is studied how the flow of transverse momenta (Σ P sub(T) or Σ ER) behaves in multi-particle production phenomena in the region of visible energy 10 -1000 TeV, using the emulsion chamber data of Brazil-Japan Collaboration. (Author) [pt

238U neutron-induced fission cross section for incident neutron energies between 5 eV and 3.5 MeV

International Nuclear Information System (INIS)

Difilippo, F.C.; Perez, R.B.; de Saussure, G.; Olsen, D.K.; Ingle, R.W.

1979-01-01

A measurement of the 238 U neutron-induced fission cross section was performed at the ORELA Linac facility in the neutron energy range between 5 eV and 3.5 MeV. The favorable signal-to-background ratio and high resolution of this experiment resulted in the identificaion of 85 subthreshold fission resonances or clusters of resonances in the neutron energy region between 5 eV and 200 keV. The fission data below 100 keV are characteristic of a weak coupling situation between Class I and Class II levels. The structure of the fission levels at the 720 eV and 1210 eV fission clusters is discussed. There is an apparent enhancement of the fission cross section at the opening of the 2 + neutron inelastic channel in 238 U at 45 keV. An enhancement of the subthreshold fission cross section between 100 keV and 200 keV is tentatively interpreted in terms of the presence of a Class II, partially damped vibrational level. There is a marked structure in the fission cross section above 200 keV up to and including the plateau between 2 and 3.5 MeV. 11 figures and 6 tables

Tritium retention in S-65 beryllium after 100 eV plasma exposure

Energy Technology Data Exchange (ETDEWEB)

Causey, R.A. [Sandia National Labs., Livermore, CA (United States); Longhurst, G.R. [Idaho National Engineering Laboratories, Idaho Falls, 83415 (United States); Harbin, W. [Los Alamos National Laboratories, Los Alamos, NM 87545 (United States)

1997-02-01

The tritium plasma experiment (TPE) has been used to measure the retention of tritium in S-65 beryllium under conditions similar to that expected for the international thermonuclear experimental reactor (ITER). Beryllium samples 2 mm thick and 50 mm in diameter were exposed to a plasma of tritium and deuterium. The particle flux striking the samples was varied from approximately 1 x 10{sup 17} (D+T)/cm{sup 2} s up to about 3 x 10{sup 18} (D+T)/cm{sup 2} s. The beryllium samples were negatively biased to elevate the energy of the impinging ions to 100 eV. The temperature of the samples was varied from 373 K to 973 K. Exposure times of 1 h were used. Subsequent to the plasma exposure, the samples were outgassed in a separate system where 99% He and 1% H{sub 2} gas was swept over the samples during heating. The sweep gas along with the released tritium was sent through an ionization chamber, through a copper oxide catalyst bed, and into a series of glycol bubblers. The amount of released tritium was determined both by the ionization chamber and by liquid scintillation counting of the glycol. Tritium retention in the beryllium disks varied from a high of 2.4 x 10{sup 17} (D+T)/cm{sup 2} at 373 K to a low of 1 x 10{sup 16} (D+T)/cm{sup 2} at 573 K. For almost every case, the tritium retention in the beryllium was less than that calculated using the C=0 boundary condition at the plasma facing surface. It is believed that this lower than expected retention is due to rapid release of tritium from the large specific surface area created in the implant zone due to the production of voids, bubbles, and blisters. (orig.).

Tritium retention in S-65 beryllium after 100 eV plasma exposure

Science.gov (United States)

Causey, Rion A.; Longhurst, Glen R.; Harbin, Wally

1997-02-01

The tritium plasma experiment (TPE) has been used to measure the retention of tritium in S-65 beryllium under conditions similar to that expected for the international thermonuclear experimental reactor (ITER). Beryllium samples 2 mm thick and 50 mm in diameter were exposed to a plasma of tritium and deuterium. The particle flux striking the samples was varied from approximately 1 × 10 17 ( D + T)/ cm2s up to about 3 × 10 18 ( D + T)/ cm2s. The beryllium samples were negatively biased to elevate the energy of the impinging ions to 100 eV. The temperature of the samples was varied from 373 K to 973 K. Exposure times of 1 h were used. Subsequent to the plasma exposure, the samples were outgassed in a separate system where 99% He and 1% H 2 gas was swept over the samples during heating. The sweep gas along with the released tritium was sent through an ionization chamber, through a copper oxide catalyst bed, and into a series of glycol bubblers. The amount of released tritium was determined both by the ionization chamber and by liquid scintillation counting of the glycol. Tritium retention in the beryllium disks varied from a high of 2.4 × 10 17 ( D + T)/ cm2 at 373 K to a low of 1 × 10 16 ( D + T)/ cm2 at 573 K. For almost every case, the tritium retention in the beryllium was less than that calculated using the C = 0 boundary condition at the plasma facing surface. It is believed that this lower than expected retention is due to rapid release of tritium from the large specific surface area created in the implant zone due to the production of voids, bubbles, and blisters.

Experimental search for solar hidden photons in the eV energy range using kinetic mixing with photons

International Nuclear Information System (INIS)

Mizumoto, T.; Ohta, R.; Horie, T.; Suzuki, J.; Minowa, M.; Inoue, Y.

2013-01-01

We have searched for solar hidden photons in the eV energy range using a dedicated hidden photon detector. The detector consisted of a parabolic mirror with a diameter of 500 mm and a focal length of 1007 mm installed in a vacuum chamber, and a photomultiplier tube at its focal point. The detector was attached to the Tokyo axion helioscope, Sumico which has a mechanism to track the sun. From the result of the measurement, we found no evidence for the existence of hidden photons and set a limit on the photon-hidden photon mixing parameter χ depending on the hidden photon mass m γ'

Plastic behaviour of Zircaloy-4 in the temperature range 77-1000 K

International Nuclear Information System (INIS)

Derep, J.L.; Ibrahim, S.; Rouby, D.; Fantozzi, G.; Gobin, P.

1979-01-01

Tensile tests were carried out on Zircaloy-4 over a temperature range 77-1000 K. So, we have determined the flow stress variations as a function of temperature and strain rate. Two thermally activated zones were observed between about 77 and 600 K, a plateau stress between 600 and 700 K and an other thermally activated zone above 700 K. The various mechanisms which can be responsible for the thermally activated and athermal zones are discussed in the light of experimental results. The mechanical behaviour of Zircaloy-4 appears similar to the zirconium-oxygen alloys one. (orig.) [de

Total cross sections for electron scattering by CO2 molecules in the energy range 400 endash 5000 eV

International Nuclear Information System (INIS)

Garcia, G.; Manero, F.

1996-01-01

Total cross sections for electron scattering by CO 2 molecules in the energy range 400 endash 5000 eV have been measured with experimental errors of ∼3%. The present results have been compared with available experimental and theoretical data. The dependence of the total cross sections on electron energy shows an asymptotic behavior with increasing energies, in agreement with the Born-Bethe approximation. In addition, an analytical formula is provided to extrapolate total cross sections to higher energies. copyright 1996 The American Physical Society

Comparative severe accident analysis of WWER 1000/B 320 LOCA DN100 computed by computer codes ASTEC V1.1 and SCDAP/RELAP5

International Nuclear Information System (INIS)

Kalchev, B.; Dimov, D.; Tusheva, P.; Mladenov, I.

2005-01-01

This paper presents the modelling approach for LOCA 100 mm sequence for WWER 1000-B 320 type of reactor with the integral ASTEC computer code and SCDAP/RELAP5 computer code. As a basic input deck the reference input file for Balakovo NPP from the released ASTEC CD has been applied. As a first part of the calculations for the SBLOCA sequence the ASTEC v1.1 modules CESAR, DIVA and CPA have been activated in a coupled mode. For SCDAP/RELAP5 calculation input deck for WWER 1000-B 320 has been applied which meant to be closer to the initial boundary conditions applied for ASTEC WWER 1000 input deck. A SBLOCA 100 mm comparison between ASTEC v1.1 and SCADAP/RELAP5 has been presented. ASTEC predicts vessel failure at 15620 s. ASTEC and SCDAP/RELAP5 give close but not similar results - this could be observed on the trends. The comparison of 100 mm-break shows that SCDAP/RELAP5 predicts clear phenomenological changes in primary pressure evolution and molten pool formation. Similar hydrogen production mass for both codes around 5000 s is detected

A survey of photoproducts of an irradiated oligodeoxynucleotide by monochromatic photons with the energy ranged from 6.5 to 22.5 eV

International Nuclear Information System (INIS)

Ito, Takashi; Saito, Mikio; Taniguchi, Taketoshi

1987-01-01

We have irradiated 2'-deoxyadenylyl-(3'-5')-2'-deoxyadenosine (dephospho(dA) 2 ) in solid state with a newly developed synchrotron irradiation system over 6.5 to 22.5 eV photon energy range (190 to 55 nm in wavelength). Densitometric analysis of thin-layer chromatogram of photoproducts indicated that adenine and deoxyadenosine monophosphate were commonly produced above 7.3 eV (170 nm) in approximately equal amount. Deoxyribose was not detected by the fluorescence method with scratched materials from the chromatogram at any location except deoxyadenosine monophosphate and parent oligonucleotide positions. The photoproducts above mentioned were not observed at 6.5 eV (190 nm) even after very high radiation fluence. The energy dependence of this degradation indicates that the shorter the wavelength in use the smaller the fluence it requires. Careful examination of irradiated oligonucleotide on the chromatograms shows that the major portion of deoxyadenosine monophosphate so produced was the 5'phospho derivative. This site-selective degradation, independent of photon energy, seemed to be a remarkable characteristic of vacuum-UV induced effects above 7 eV. It is hypothesised that the deoxypentose moiety was first destroyed in one of the nucleoside residues due to the strong absorption in the sugar-phosphate group, liberating adenine on the one hand and leaving 5'-deoxyadenosine monophosphate. (author)

Observation of >400-eV precursor plasmas from low-wire-number copper arrays at the 1-MA zebra facility.

Science.gov (United States)

Coverdale, C A; Safronova, A S; Kantsyrev, V L; Ouart, N D; Esaulov, A A; Deeney, C; Williamson, K M; Osborne, G C; Shrestha, I; Ampleford, D J; Jones, B

2009-04-17

Experiments with cylindrical copper wire arrays at the 1-MA Zebra facility show that high temperatures exist in the precursor plasmas formed when ablated wire array material accretes on the axis prior to the stagnation of a z pinch. In these experiments, the precursor radiated approximately 20% of the >1000 eV x-ray output, and time-resolved spectra show substantial emission from Cu L-shell lines. Modeling of the spectra shows an increase in temperature as the precursor forms, up to approximately 450 eV, after which the temperature decreases to approximately 220-320 eV until the main implosion.

Primary proton and helium spectra at energy range from 50 TeV to 1015 eV observed with the new Tibet AS core detector array

Directory of Open Access Journals (Sweden)

Huang Jing

2013-06-01

Full Text Available A new EAS hybrid experiment has been designed by constructing a YAC (Yangbajing Air shower Core detector array inside the existing Tibet-III air shower array. The first step of YAC, called “YAC-I” has been successfully carried out in 2009–2010 together with Tibet-III air-shower array. YAC-II has also been operated from 2011. Preliminary results of YAC-I and performance of YAC-II are presented in this paper. The primary proton and helium spectra at energy range from50 TeV to 1015 eV derived from YAC-I data based on QGSJET2 and SIBYLL2.1 are reported. The obtained P+He spectrum is smoothly connected with directobservation data below 100 TeV and also with our previously reported results at higher energies within statistical error s. Based on these results and the sharp kneeof all-particle energy spectrum observed by our experiment, the possible origin of the sharp knee is discussed. See the published papers.

Compact, self-contained enhanced-vision system (EVS) sensor simulator

Science.gov (United States)

Tiana, Carlo

2007-04-01

We describe the model SIM-100 PC-based simulator, for imaging sensors used, or planned for use, in Enhanced Vision System (EVS) applications. Typically housed in a small-form-factor PC, it can be easily integrated into existing out-the-window visual simulators for fixed-wing or rotorcraft, to add realistic sensor imagery to the simulator cockpit. Multiple bands of infrared (short-wave, midwave, extended-midwave and longwave) as well as active millimeter-wave RADAR systems can all be simulated in real time. Various aspects of physical and electronic image formation and processing in the sensor are accurately (and optionally) simulated, including sensor random and fixed pattern noise, dead pixels, blooming, B-C scope transformation (MMWR). The effects of various obscurants (fog, rain, etc.) on the sensor imagery are faithfully represented and can be selected by an operator remotely and in real-time. The images generated by the system are ideally suited for many applications, ranging from sensor development engineering tradeoffs (Field Of View, resolution, etc.), to pilot familiarization and operational training, and certification support. The realistic appearance of the simulated images goes well beyond that of currently deployed systems, and beyond that required by certification authorities; this level of realism will become necessary as operational experience with EVS systems grows.

Inhibition of enterovirus 71 (EV-71 infections by a novel antiviral peptide derived from EV-71 capsid protein VP1.

Directory of Open Access Journals (Sweden)

Chee Wah Tan

Full Text Available Enterovirus 71 (EV-71 is the main causative agent of hand, foot and mouth disease (HFMD. In recent years, EV-71 infections were reported to cause high fatalities and severe neurological complications in Asia. Currently, no effective antiviral or vaccine is available to treat or prevent EV-71 infection. In this study, we have discovered a synthetic peptide which could be developed as a potential antiviral for inhibition of EV-71. Ninety five synthetic peptides (15-mers overlapping the entire EV-71 capsid protein, VP1, were chemically synthesized and tested for antiviral properties against EV-71 in human Rhabdomyosarcoma (RD cells. One peptide, SP40, was found to significantly reduce cytopathic effects of all representative EV-71 strains from genotypes A, B and C tested, with IC(50 values ranging from 6-9.3 µM in RD cells. The in vitro inhibitory effect of SP40 exhibited a dose dependent concentration corresponding to a decrease in infectious viral particles, total viral RNA and the levels of VP1 protein. The antiviral activity of SP40 peptide was not restricted to a specific cell line as inhibition of EV-71 was observed in RD, HeLa, HT-29 and Vero cells. Besides inhibition of EV-71, it also had antiviral activities against CV-A16 and poliovirus type 1 in cell culture. Mechanism of action studies suggested that the SP40 peptide was not virucidal but was able to block viral attachment to the RD cells. Substitutions of arginine and lysine residues with alanine in the SP40 peptide at positions R3A, R4A, K5A and R13A were found to significantly decrease antiviral activities, implying the importance of positively charged amino acids for the antiviral activities. The data demonstrated the potential and feasibility of SP40 as a broad spectrum antiviral agent against EV-71.

ACT-1000. Group activation cross-section library for WWER-1000 type reactors

Energy Technology Data Exchange (ETDEWEB)

Zolotarev, K I; Pashchenko, A B [National Research Centre - A.I. Leipunsky Institute for Physics and Power Engineering, Obninsk (Russian Federation)

2001-10-01

The ACT-1000, a problem-oriented library of group-averaged activation cross-sections for WWER-1000 type reactors, is based on evaluated microscopic cross-section data files. The ACT-1000 data library was designed for calculating induced activity for the main dose-generated nuclides contained in WWER-1000 structural materials. In preparing the ACT-1000 library, 47 group-averaged cross-section data for the 10{sup -9}-17.33 MeV energy range were used to calculate the spatial-energy neutron flux distribution. (author)

Absorption effects in electron-sulfur-dioxide collisions

Energy Technology Data Exchange (ETDEWEB)

Machado, L. E.; Sugohara, R. T.; Santos, A. S. dos [Departamento de Fisica, UFSCar, 13565-905 Sao Carlos-SP (Brazil); Lee, M.-T.; Iga, I.; Souza, G. L. C. de [Departamento de Quimica, UFSCar, 13565-905 Sao Carlos-SP (Brazil); Homem, M. G. P.; Michelin, S. E. [Departamento de Fisica, UFSC, 88040-970 Florianopolis-SC (Brazil); Brescansin, L. M. [Instituto de Fisica ' ' Gleb Wataghin' ' , UNICAMP, 13083-970 Campinas-SP (Brazil)

2011-09-15

A joint experimental-theoretical study on electron-SO{sub 2} collisions in the low and intermediate energy range is reported. More specifically, experimental elastic differential, integral, and momentum transfer cross sections in absolute scale are measured in the 100-1000 eV energy range using the relative-flow technique. Calculated elastic differential, integral, and momentum transfer cross sections as well as grand-total and total absorption cross sections are also presented in the 1-1000 eV energy range. A complex optical potential is used to represent the electron-molecule interaction dynamics, whereas the Schwinger variational iterative method combined with the distorted-wave approximation is used to solve the scattering equations. Comparison of the present results is made with the theoretical and experimental results available in the literature.

Inherited MST1 deficiency underlies susceptibility to EV-HPV infections.

Directory of Open Access Journals (Sweden)

Amandine Crequer

Full Text Available Epidermodysplasia verruciformis (EV is characterized by persistent cutaneous lesions caused by a specific group of related human papillomavirus genotypes (EV-HPVs in otherwise healthy individuals. Autosomal recessive (AR EVER1 and EVER2 deficiencies account for two thirds of known cases of EV. AR RHOH deficiency has recently been described in two siblings with EV-HPV infections as well as other infectious and tumoral manifestations. We report here the whole-exome based discovery of AR MST1 deficiency in a 19-year-old patient with a T-cell deficiency associated with EV-HPV, bacterial and fungal infections. MST1 deficiency has recently been described in seven patients from three unrelated kindreds with profound T-cell deficiency and various viral and bacterial infections. The patient was also homozygous for a rare ERCC3 variation. Our findings broaden the clinical range of infections seen in MST1 deficiency and provide a new genetic etiology of susceptibility to EV-HPV infections. Together with the recent discovery of RHOH deficiency, they suggest that T cells are involved in the control of EV-HPVs, at least in some individuals.

Electron-impact rotationally elastic total cross sections for H2CO and HCOOH over a wide range of incident energy (0.01-2000 eV)

International Nuclear Information System (INIS)

Vinodkumar, Minaxi; Bhutadia, Harshad; Antony, Bobby; Mason, Nigel

2011-01-01

This paper reports computational results of the total cross sections for electron impact on H 2 CO and HCOOH over a wide range of electron impact energies from 0.01 eV to 2 keV. The total cross section is presented as sum of the elastic and electronic excitation cross sections for incident energies. The calculation uses two different methodologies, below the ionization threshold of the target the cross section is calculated using the UK molecular R-matrix code through the Quantemol-N software package while cross sections at higher energies are evaluated using the spherical complex optical potential formalism. The two methods are found to be consistent at the transition energy (∼15 eV). The present results are, in general, found to be in good agreement with previous experimental and theoretical results (wherever available) and, thus, the present results can serve as a benchmark for the cross section over a wide range of energy.

Proceedings of the EV2010 electric vehicles conference and trade show

Energy Technology Data Exchange (ETDEWEB)

Elwood, M. [Electric Mobility Canada, Mississauga, ON (Canada); Dubois-Phillips, M. [BC Hydro, Vancouver, BC (Canada)] (comps.)

2010-07-01

This conference provided a forum to address the challenges facing the adoption of electric vehicles (EV) in Canada. Topics of discussions ranged from the Canadian public's levels of awareness of EVs, motivators to adoption of EVs and barriers to broader acceptance and market diffusion of EVs. Five sessions related to vehicle technologies focused on vehicles and their components, energy storage, power management, testing and operating conditions. Three sessions on infrastructure and other readiness measures, focused on grid capacity and impacts, charging infrastructure and the vehicle/grid interface. Four sessions on public policies and institutional changes focused on how EVs are a critical pathway to address peak oil and greenhouse gases, and that public policy is needed to support adoption of the technology. Four sessions on commercialization and environmental impacts focused on market forecasts, the need for EVs and on business models used by EV manufacturers to promote the technology and explain the environmental benefits. The conference featured 65 presentations, of which 20 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Electron scattering from alkenes in the energy range 200-4500 eV

International Nuclear Information System (INIS)

Wickramarachchi, P.; Palihawadana, P.; Villela, G.; Ariyasinghe, W.M.

2009-01-01

Total electron scattering cross sections (TCS) of C 2 H 4 (ethylene), C 3 H 6 (propene), C 4 H 8 (butene) and C 4 H 6 (1,3-butadiene) have been obtained for 200-4500 eV electrons by the measurement of electron-beam intensity attenuation through a gas cell. An analytical expression is deduced to predict the intermediate energy TCS of chain-like hydrocarbons with C-C single and double bonds. The present experimental TCS are compared with the previous experimental measurements and the predictions by theoretical models.

The angular distributions of charged secondaries in electromagnetic and hadronic extensive air showers at 10, 100, 1000 and 10 000 TeV

International Nuclear Information System (INIS)

Trzupek, A.; Mikocki, S.; Gress, J.; Kochocki, J.; Poirier, J.

1991-01-01

The angular distributions of secondary electrons and muons in extensive air showers (EAS) initiated by 10, 100, 1000 and 10 000 TeV gamma rays and protons are obtained with the aid of a new, hybrid Monte Carlo simulation method. In this method, a three-dimensional program is constructed out of two existing software codes: SHOWERSIM and EGS4. This procedure allows for fast, yet precise, calculations down to low secondary particle energies. The dependence of the angular distributions for different threshold energies is presented for 1000 TeV primary gamma ray and proton energy. (author)

Molecular absorption by atmospheric gases in the 100-1000 GHz region

Science.gov (United States)

Llewellyn-Jones, D. T.; Knight, R. J.

The two principal atmospheric absorbers in the near-mm wavelength region are oxygen and water vapor. In order to measure the degree of water vapor absorption with the required precision, a large untuned resonator was constructed, consisting of a copper cylindrical structure with a Q-value close to one million at 100 GHz. A comparison of observed absorption values with theoretical predictions show a marked discrepancy. Without laboratory measurements such as the present, existing atmospheric attenuation models are likely to be inaccurate and misleading, especially at the lower range of tropospheric temperatures.

Impact of Fast Charging on Life of EV Batteries; NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

Neubauer, Jeremy; Wood, Eric; Burton, Evan; Smith, Kandler; Pesaran, Ahmad

2015-05-03

Installation of fast charging infrastructure is considered by many as one of potential solutions to increase the utility and range of electric vehicles (EVs). This is expected to reduce the range anxiety of drivers of EVs and thus increase their market penetration. Level 1 and 2 charging in homes and workplaces is expected to contribute to the majority of miles driven by EVs. However, a small percentage of urban driving and most of inter-city driving could be only achieved by a fast-charging network. DC fast charging at 50 kW, 100 kW, 120 kW compared to level 1 (3.3 kW) and level 2 (6.6 kW) results in high-current charging that can adversely impact the life of the battery. In the last couple of years, we have investigated the impact of higher current rates in batteries and potential of higher temperatures and thus lower service life. Using mathematical models, we investigated the temperature increase of batteries due to higher heat generation during fast charge and have found that this could lead to higher temperatures. We compared our models with data from other national laboratories both for fine-tuning and calibration. We found that the incremental temperature rise of batteries during 1C to 3C fast charging may reduce the practical life of the batteries by less than 10% over 10 to 15 years of vehicle ownership. We also found that thermal management of batteries is needed for fast charging to prevent high temperature excursions leading to unsafe conditions.

Wide range scaling laws for radiation driven shock speed, wall albedo and ablation parameters for high-Z materials

Science.gov (United States)

Mishra, Gaurav; Ghosh, Karabi; Ray, Aditi; Gupta, N. K.

2018-06-01

Radiation hydrodynamic (RHD) simulations for four different potential high-Z hohlraum materials, namely Tungsten (W), Gold (Au), Lead (Pb), and Uranium (U) are performed in order to investigate their performance with respect to x-ray absorption, re-emission and ablation properties, when irradiated by constant temperature drives. A universal functional form is derived for estimating time dependent wall albedo for high-Z materials. Among the high-Z materials studied, it is observed that for a fixed simulation time the albedo is maximum for Au below 250 eV, whereas it is maximum for U above 250 eV. New scaling laws for shock speed vs drive temperature, applicable over a wide temperature range of 100 eV to 500 eV, are proposed based on the physics of x-ray driven stationary ablation. The resulting scaling relation for a reference material Aluminium (Al), shows good agreement with that of Kauffman's power law for temperatures ranging from 100 eV to 275 eV. New scaling relations are also obtained for temperature dependent mass ablation rate and ablation pressure, through RHD simulation. Finally, our study reveals that for temperatures above 250 eV, U serves as a better hohlraum material since it offers maximum re-emission for x-rays along with comparable mass ablation rate. Nevertheless, traditional choice, Au works well for temperatures below 250 eV. Besides inertial confinement fusion (ICF), the new scaling relations may find its application in view-factor codes, which generally ignore atomic physics calculations of opacities and emissivities, details of laser-plasma interaction and hydrodynamic motions.

Reflectivity of single-crystal GeS from 0.1-30 eV

International Nuclear Information System (INIS)

Wiley, J.D.; Buckel, W.J.; Braun, W.; Fehrenbach, G.W.; Himpsel, F.J.; Koch, E.E.

1976-03-01

The reflectivity of single-crystal, orthorhombic GeS has been measured at 300 K for all three polarizations in the photon energy range 0.1-30 eV. Eleven distinct peaks or shoulders are observed, about half of which can be associated with known structure in the valence-band density-of-states. A Kramers-Kronig analysis was performed, giving the optical constants and energy-loss functions in the 0-25 eV range. (orig.) [de

X-ray attenuation cross sections for energies 100 eV to 100 keV and elements Z = 1 to Z = 92

International Nuclear Information System (INIS)

Saloman, E.B.; Hubbell, J.H.; Scofield, J.H.

1988-01-01

This work presents for the energy range 0.1--100 keV the National Bureau of Standards (NBS) database of experimental x-ray attenuation coefficients (total absorption cross sections) and cross sections calculated using a relativistic Hartree--Slater model for the photoelectric cross section for all elements of atomic number Z = 1--92. The information is displayed in both tabular and graphical form. Also shown on the graphs are cross sections obtained using the semiempirical set of recommended values of B. L. Henke and co-workers (Atomic Data and Nuclear Data Tables 27, 1 (1982)). A bibliography of the NBS database for this energy range is included. copyright 1988 Academic Press, Inc

Spectra of γ-rays from capture of 2 eV to 9 x 104 eV neutrons by 181Ta

International Nuclear Information System (INIS)

Stelts, M.L.

Using new experimental techniques, the spectra of γ-rays from the capture of neutrons by 181 Ta were measured at the Livermore 100-MeV linac for neutrons from 2 eV to 9 x 10 4 eV with a (Ge(Li)-NaI) three-crystal spectrometer. Individual primary γ-ray lines were resolved to 1778-keV excitation in 182 Ta. Neutron resonances were resolved to 200-eV neutron energy. Data analysis techniques and codes were developed to extract positions and intensities of resolved transitions from the large data matrices accumulated in this experiment. Techniques were developed to unfold the unresolved γ-ray spectra using the simple response of the three-crystal spectrometer. The resolved transition data were used to place 110 states with spin and parity assignments in the 182 Ta level diagram below 1780-keV excitation. A set of 1240 E1 transition strengths were analyzed to extract 1.38 +- 0.11 degrees of freedom for the most likely chisquared fit to the distribution of widths. The E1 strength function was extracted for E/sub gamma/ = 4 to 6 MeV and compared with previous results. The γ-ray spectra for E/sub gamma/ = 1.5 to 6.1 MeV were unfolded for neutron energy groups between 20 and 9 x 10 4 eV. Below 5-MeV γ-ray energy no dependence of the spectral shape on neu []ron energy was observed. (30 figures, 4 tables) (auth)

Ionic fragmentation of the isoprene molecule in the VUV energy range (12 to 310 eV)

Energy Technology Data Exchange (ETDEWEB)

Bernini, R.B., E-mail: rafael.bernini@ifrj.edu.br [Instituto Federal de Ciência e Tecnologia do Rio de Janeiro (IFRJ), 25050-100 Duque de Caxias, RJ (Brazil); Coutinho, L.H. [Instituto de Física, Universidade Federal do Rio De Janeiro (UFRJ), 21941-972 Rio de Janeiro, RJ (Brazil); Nunez, C.V. [Laboratório de Bioprospecção e Biotecnologia, Coordenação de Tecnologia e Inovação, Instituto Nacional de Pesquisas da Amazônia (INPA), 69060-001 Manaus, AM (Brazil); Castilho, R.B. de [Departamento de Química, Instituto de Ciências Exatas, Universidade Federal do Amazonas (UFAM), 69077-000 Manaus, AM (Brazil); Souza, G.G.B. de [Instituto de Química, Universidade Federal do Rio de Janeiro (UFRJ), 21949-900 Rio de Janeiro, RJ (Brazil)

2015-07-15

Highlights: • Ionic fragmentation of isoprene following valence-shell and C 1s excitation. • Experimental observation of single and double ionization processes. • Large increase in fragmentation following core excitation. • Similar dissociation pattern bellow (270 eV) and above (310 eV) core edge. • Stable molecular ion observed at all photon energies. - Abstract: Isoprene, C{sub 5}H{sub 8}, is a biogenic volatile compound emitted from plants and animals, playing an important role in atmospheric chemistry. In this work, we have studied the ionic fragmentation of the isoprene molecule induced by high energy photons (synchrotron radiation), both at the valence (12.0, 14.0, 16.0, 18.0, and 21.0 eV) and carbon 1s edge (270 and 310 eV, respectively, below and above edge) energies. The ionic fragments were mass-analyzed using a Wiley–McLaren time-of-flight spectrometer (TOF) and single (PEPICO) and double ionization coincidence (PEPIPICO) spectra were obtained. As expected, the fragmentation degree increases with increasing energy. Below and above the carbon 1s edge, the fragmentation patterns are quite similar, and basically the same fragments are observed as compared to the spectra following valence-shell ionization. Stable doubly-charged ions were not observed. A PEPIPICO spectrum has shown that the main dissociation route for doubly-ionized species corresponds to the [CH{sub 3}]{sup +}/[C{sub 4}H{sub 2–5}]{sup +} ion pair. Intense fragmentation of the isoprene molecule has been observed following valence shell and core electron ionization. The observance of basically the same fragments when moving from valence to inner-shell suggests that basically the same fragmentation routes are present in both cases. All doubly (or multiply)-charged cations are unstable, at least on a microsecond scale.

EV Charging Analysis with High EV Penetration in the Nordic Region

DEFF Research Database (Denmark)

Liu, Zhaoxi; Wu, Qiuwei

This report covers the driving pattern analysis and the electric vehicle (EV) charging ananlysis of Denmark, Sweden, Norway and Finland. The contents in the report are driving pattern analysis of the passenger cars and electrical charging load profiles of EVs based on the analyzed driving patterns...

NANO-BATTERY TECHNOLOGY FOR EV-HEV PANEL: A PIONEERING STUDY

OpenAIRE

Ataur Rahman; M. Rashid; A. K. M. Mohiuddin; M. N. A. Hawlader

2015-01-01

Global trends toward CO2 reduction and resource efficiency have significantly increased the importance of lightweight materials for automobile original equipment manufacturers (OEM). CO2 reduction is a fundamental driver for a more lightweight automobile. The introduction of Electrical Vehicles (EVs) is one initiative towards this end. However EVs are currently facing several weaknesses: limited driving range, battery pack heaviness, lack of safety and thermal control, high cost, and overall ...

Systematics of neutron-induced fission cross sections over the energy range 0.1 through 15 MeV, and at 0.0253 eV

International Nuclear Information System (INIS)

Behrens, J.W.

1977-01-01

Recent studies have shown straightforward systematic behavior as a function of constant proton and neutron number for neutron-induced fission cross sections of the actinide elements in the incident-neutron energy range 3 to 5 MeV. In this report, the second in a series, fission cross-section values are studied over the MeV incident-neutron energy range, and at 0.0253 eV. Fission-barrier heights and neutron-binding energies are correlated by constant proton and neutron number; however, these systematic behaviors alone do not explain the trends observed in the fission cross-section values

Gross features of nuclear interactions around 1015 eV through observation of gamma ray families

International Nuclear Information System (INIS)

Semba, Hiroshi

1983-01-01

A systematic analysis is made on the 106 γ-ray families with visible energy in the range of 100--300 TeV observed in the Chacaltaya emulsion chamber experiment. A new method called 'decascading' is introduced to pick up a cluster of γ-rays and electrons in a family, so that the cluster is an air cascade from one parent γ-ray. The application of 'decascading' method to the family data gives information on original γ-rays produced at the atmospheric nuclear interactions. The results are compared with expected ones from the simulation calculation on the base of H-quantum model, and with data from the target interactions at lower energy range (ΣE sub(γ)=20 --100 TeV). The conclusion is that the characteristics of nuclear interactions at the concerned family energy range (E 0 asymptotically equals 1,000 TeV) are in accordance with those at the target interaction range (E 0 asymptotically equals 100 TeV), with increased ratio of frequencies of a heavy fire-ball (SH-quantum) to a small and usual fire-ball (H-quantum). (author)

EV Portfolio Management and Grid Impact Study

DEFF Research Database (Denmark)

Wu, Qiuwei; Jensen, Jakob Munch; Hansen, Lars Henrik

2009-01-01

is to determine the day‐ahead charging schedules of a fleet of EVs in order to minimize the EV charging cost with EV energy constraints taken into account. In order to investigate the benefits of the spot price based EV charging scenario, two more charging scenarios have been studied as well, i.e. plug......The EV portfolio management is to develop an EV charging management algorithm in order to determine EV charging schedules with the goal of utilizing renewalbe energy production for EV charging as much as possible and ensuring that EV energy requirements for driving needs are met. According...

Electron excitation cross sections for some Ar I 5d (J = 2) levels

International Nuclear Information System (INIS)

Blanco, F.; Sanchez, J.A.; Campos, J.

1992-01-01

Absolute excitation cross sections by electron impact for some 5d levels with J = 2 of Ar I have been measured by the optical method. Excitation functions for electron energies in the range from the excitation threshold to 1000 eV are also reported. A delayed coincidence analysis of the de-excitation at 100 eV electron energy allowed for the subtraction of radiative cascades. The resulting excitation cross sections are between 7.3 and 12x10 -20 cm 2 . (author)

Recombination in the evolution of enterovirus C species sub-group that contains types CVA-21, CVA-24, EV-C95, EV-C96 and EV-C99.

Directory of Open Access Journals (Sweden)

Teemu Smura

Full Text Available Genetic recombination is considered to be a very frequent phenomenon among enteroviruses (Family Picornaviridae, Genus Enterovirus. However, the recombination patterns may differ between enterovirus species and between types within species. Enterovirus C (EV-C species contains 21 types. In the capsid coding P1 region, the types of EV-C species cluster further into three sub-groups (designated here as A-C. In this study, the recombination pattern of EV-C species sub-group B that contains types CVA-21, CVA-24, EV-C95, EV-C96 and EV-C99 was determined using partial 5'UTR and VP1 sequences of enterovirus strains isolated during poliovirus surveillance and previously published complete genome sequences. Several inter-typic recombination events were detected. Furthermore, the analyses suggested that inter-typic recombination events have occurred mainly within the distinct sub-groups of EV-C species. Only sporadic recombination events between EV-C species sub-group B and other EV-C sub-groups were detected. In addition, strict recombination barriers were inferred for CVA-21 genotype C and CVA-24 variant strains. These results suggest that the frequency of inter-typic recombinations, even within species, may depend on the phylogenetic position of the given viruses.

EV Charging Infrastructure Roadmap

International Nuclear Information System (INIS)

Karner, Donald; Garetson, Thomas; Francfort, Jim

2016-01-01

As highlighted in the U.S. Department of Energy's EV Everywhere Grand Challenge, vehicle technology is advancing toward an objective to ''... produce plug-in electric vehicles that are as affordable and convenient for the average American family as today's gasoline-powered vehicles ...'' [1] by developing more efficient drivetrains, greater battery energy storage per dollar, and lighter-weight vehicle components and construction. With this technology advancement and improved vehicle performance, the objective for charging infrastructure is to promote vehicle adoption and maximize the number of electric miles driven. The EV Everywhere Charging Infrastructure Roadmap (hereafter referred to as Roadmap) looks forward and assumes that the technical challenges and vehicle performance improvements set forth in the EV Everywhere Grand Challenge will be met. The Roadmap identifies and prioritizes deployment of charging infrastructure in support of this charging infrastructure objective for the EV Everywhere Grand Challenge

Reevaluation and Validation of the 241Pu Resonance Parameters in the Energy Range Thermal to 20 eV

International Nuclear Information System (INIS)

Derrien, H.; Leal, L.C.; Courcelle, A.; Santamarina, A.

2005-01-01

A new SAMMY analysis of the 241 Pu resonance parameters from thermal to 20 eV is presented. This evaluation takes into account the trends given by integral experiments [post-irradiation experiments performed in French pressurized water reactors (PWRs)]. Compared to the previous evaluations performed by Derrien and de Saussure, the capture cross section increases especially in the 0.26-eV resonance. It is shown that the new resonance parameters proposed in this work improve the prediction of the 242 Pu buildup in a PWR, which was significantly underestimated with the previous evaluations

EV Charging Infrastructure Roadmap

Energy Technology Data Exchange (ETDEWEB)

Karner, Donald [Electric Transportation Inc., Rogers, AR (United States); Garetson, Thomas [Electric Transportation Inc., Rogers, AR (United States); Francfort, Jim [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-08-01

As highlighted in the U.S. Department of Energy’s EV Everywhere Grand Challenge, vehicle technology is advancing toward an objective to “… produce plug-in electric vehicles that are as affordable and convenient for the average American family as today’s gasoline-powered vehicles …” [1] by developing more efficient drivetrains, greater battery energy storage per dollar, and lighter-weight vehicle components and construction. With this technology advancement and improved vehicle performance, the objective for charging infrastructure is to promote vehicle adoption and maximize the number of electric miles driven. The EV Everywhere Charging Infrastructure Roadmap (hereafter referred to as Roadmap) looks forward and assumes that the technical challenges and vehicle performance improvements set forth in the EV Everywhere Grand Challenge will be met. The Roadmap identifies and prioritizes deployment of charging infrastructure in support of this charging infrastructure objective for the EV Everywhere Grand Challenge

Framing-camera tube developed for sub-100-ps range

International Nuclear Information System (INIS)

Anon.

1978-01-01

A new framing-camera tube, developed by Electronics Engineering, is capable of recording two-dimensional image frames with high spatial resolution in the sub-100-ps range. Framing is performed by streaking a two-dimensional electron image across narrow slits; the resulting electron-line images from the slits are restored into a framed image by a restorer deflector operating synchronously with the dissector deflector. We have demonstrated its performance in a prototype tube by recording 125-ps-duration framed images of 2.5-mm patterns. The limitation in the framing speed is in the external electronic drivers for the deflectors and not in the tube design characteristics. Shorter frame durations (below 100 ps) can be obtained by use of faster deflection drivers

Study of Primary Cosmic Ray Electrons In Energy Range 10^11 - 10^13 Ev By Pamela Instrument.

Science.gov (United States)

Voronov, S.; Pamela Collaboration

The main goal of the magnetic spectrometer PAMELA is the study of antiparticle fluxes with energy up to 300 GeV in cosmic rays on board satellite. A modification of instrument was done by introducing of neutron detector. This device was placed under imaging calorimeter and bottom scintillator counter. It consists of two layers of 36 3He gas counters enveloped by a polyethylene moderator. The neutron detector gives additional possibility to identify the antiprotons going in aperture of spectrome- ter and generating the nuclear cascade in tungsten plates of calorimeter. This shower is followed by big number of neutrons in contrast to electromagnetic one caused by elec- tron or positron. From other side the combination of the imaging calorimeter, bottom scintillator and neutron detector constitute the independent instrument with large field of view which gives the possibility to measure the electron-positron cosmic ray com- ponent in energy range 1011-1013 eV with a rejection factor of order 10-4 regarding to nuclear one.

Study on the economic and environmental benefits of different EV powertrain topologies

International Nuclear Information System (INIS)

Wang, Bin; Xu, Min; Yang, Li

2014-01-01

Highlights: • EV powertrain topologies can be realized by flexible distributed electric motors. • Model-based design optimization method is used to analyze and evaluate the EV. • The wheel-hub drive with reducer possesses the most competitive advantages. • US06 and NYCC result in the deterioration of EVs’ cost and GHG emissions. - Abstract: Numerous feasible schemes of powertrain topology can be designed for the electric vehicles (EVs) based on the distributed configurations of the electric motors. In this study, the effects of different EV powertrain topologies on the energy efficiency, vehicle ownership cost and lifecycle greenhouse gas (GHG) emissions of EVs are investigated. Energy-based vehicle simulation model including the regenerative braking function and battery degradation prediction method is established firstly. An optimization scheme combining the energy-based vehicle simulation model is conducted to minimize the electric energy consumption under various scenarios and driving conditions. Then the vehicle ownership cost and lifecycle GHG emissions of EVs are evaluated based on Chinese EV market and electricity grid. The sensitivity analyses of EV powertrain topology are implemented based on the different vehicle weights, CO 2 intensities of electricity and all-electric ranges. Results show that EVs using the powertrain of wheel-hub drive with the gear reducer have lower energy consumption. Furthermore, the driving cycles with more aggressive acceleration/deceleration and frequently stop-and-go conditions can increase both the vehicle ownership cost and lifecycle GHG emissions simultaneously. Chinese city traffic conditions will help EVs to obtain more benefits in respect of the economy and environment

Electron impact collision strengths and transition rates for extreme ultraviolet emission from Xe10+

International Nuclear Information System (INIS)

Shen Yunfeng; Gao Cheng; Zeng Jiaolong

2009-01-01

The energy levels, oscillator strengths, and electron impact collision strengths are calculated for the Xe 10+ ion using the configuration interaction scheme implemented by the Flexible Atomic Code. These data pertain to the 3917 levels belonging to the following configurations: 4s 2 4p 6 4d 8 , 4s 2 4p 6 4d 7 4f, 4s 2 4p 6 4d 7 5l (l = s, p, d, or f), 4s 2 4p 5 4d 9 , 4s 2 4p 5 4d 8 4f, 4s 2 4p 5 4d 8 5l, 4s 2 4p 6 4d 6 5s5p, 4s 2 4p 6 4d 6 5p5d. Configuration interactions among these configurations are included in the calculation. Collision strengths are obtained at 10 scattered electron energies (1-1000 eV) and are tabulated here at five representative energies of 10, 50, 100, 500, and 1000 eV. Effective collision strengths are obtained by assuming a Maxwellian electron velocity distribution at 10 temperatures ranging from 10 to 100 eV, and are tabulated at five representative temperatures of 10, 30, 50, 70 and 100 eV in this work. The whole data set should be useful for research involving extreme ultraviolet emission from Xe 10+

XRAY applied program package for calculation of electron-photon fields in the energy range of 1-1000 keV

International Nuclear Information System (INIS)

Lappa, A.V.; Khadyeva, Z.M.; Burmistrov, D.S.; Vasil'ev, O.N.

1990-01-01

The package of applied XRAY programs is intended for calculating the linear and fluctuation characteristics of photon and electron radiation fields in heterogeneous medium within 1-1000 keV energy range. The XRAY program package consists of moduli written in FORTRAN-IV and data files. 9 refs

How Do The EV Project Participants Feel about Charging Their EV at Home?

Energy Technology Data Exchange (ETDEWEB)

Francfort, James E. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-02-01

Key Observations from the Survey of the EV Project Participants; In June 2013, 72% of EV Project participants were very satisfied with their home charging experience; 21% of participants relied totally on home charging for all of their charging needs; Volt owners relied more on home charging than Leaf owners, who reported more use of away-from-home charging; 74% of participants reported that they plug in their plug-in electric vehicle (PEV) every time they park at home. Others plugged in as they determined necessary to support their driving needs; 40% of participants reported that they would not have or are unsure that in June 2013 whether they would have purchased an alternating current (AC) Level 2 electric vehicle supply equipment (EVSE) for home charging if it had not been provided by The EV Project; and 61% of participants reported that The EV Project incentive was very important or important in their decision to obtain a PEV.

Measurements of the total neutron cross-section of cerium and thulium in the energy range from 1.8 MeV to 1.8 eV

International Nuclear Information System (INIS)

Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Abu-Elnour, F.; Hamouda, I.

1979-01-01

Total neutron cross-section measurements have been carried out for cerium and thulium in the energy range from 1.8 meV to 1.8 eV. The measurements were performed using the time-of-flight spectrometer installed in front of one of the horizontal channels of the ET-RR-1 reactor. The obtained total neutron cross-sections were analyzed using the single level Breit-Wigner formula and the magnetic form factor. The potential scattering cross-section of Ce was found to be (3.14 +- 0.3) barns. Its coherent scattering amplitude was determined from the Bragg reflections observed in the total neutron cross-section of CeO 2 and found to be (4,8 +- 0.2) fm. The potential scattering and absorption cross-sections of Tm, at E = 0.025 eV, were found to be (7.5 +- 0.7) barns and (89.1 +- 4.1) barns respectively. (orig.) [de

A Novel Recombinant Enterovirus Type EV-A89 with Low Epidemic Strength in Xinjiang, China.

Science.gov (United States)

Fan, Qin; Zhang, Yong; Hu, Lan; Sun, Qiang; Cui, Hui; Yan, Dongmei; Sikandaner, Huerxidan; Tang, Haishu; Wang, Dongyan; Zhu, Zhen; Zhu, Shuangli; Xu, Wenbo

2015-12-21

Enterovirus A89 (EV-A89) is a novel member of the EV-A species. To date, only one full-length genome sequence (the prototype strain) has been published. Here, we report the molecular identification and genomic characterization of a Chinese EV-A89 strain, KSYPH-TRMH22F/XJ/CHN/2011, isolated in 2011 from a contact of an acute flaccid paralysis (AFP) patient during AFP case surveillance in Xinjiang China. This was the first report of EV-A89 in China. The VP1 coding sequence of this strain demonstrated 93.2% nucleotide and 99.3% amino acid identity with the EV-A89 prototype strain. In the P2 and P3 regions, the Chinese EV-A89 strain demonstrated markedly higher identity than the prototype strains of EV-A76, EV-A90, and EV-A91, indicating that one or more recombination events between EV-A89 and these EV-A types might have occurred. Long-term evolution of these EV types originated from the same ancestor provides the spatial and temporal circumstances for recombination to occur. An antibody sero-prevalence survey against EV-A89 in two Xinjiang prefectures demonstrated low positive rates and low titres of EV-A89 neutralization antibody, suggesting limited range of transmission and exposure to the population. This study provides a solid foundation for further studies on the biological and pathogenic properties of EV-A89.

Inhibition of EV71 by curcumin in intestinal epithelial cells

Science.gov (United States)

Chio, Chi-Chong; Lin, Jhao-Yin

2018-01-01

EV71 is a positive-sense single-stranded RNA virus that belongs to the Picornaviridae family. EV71 infection may cause various symptoms ranging from hand-foot-and-mouth disease to neurological pathological conditions such as aseptic meningitis, ataxia, and acute transverse myelitis. There is currently no effective treatment or vaccine available. Various compounds have been examined for their ability to restrict EV71 replication. However, most experiments have been performed in rhabdomyosarcoma or Vero cells. Since the gastrointestinal tract is the entry site for this pathogen, we anticipated that orally ingested agents may exert beneficial effects by decreasing virus replication in intestinal epithelial cells. In this study, curcumin (diferuloylmethane, C21H20O6), an active ingredient of turmeric (Curcuma longa Linn) with anti-cancer properties, was investigated for its anti-enterovirus activity. We demonstrate that curcumin treatment inhibits viral translation and increases host cell viability. Curcumin does not exert its anti-EV71 effects by modulating virus attachment or virus internal ribosome entry site (IRES) activity. Furthermore, curcumin-mediated regulation of mitogen-activated protein kinase (MAPK) signaling pathways is not involved. We found that protein kinase C delta (PKCδ) plays a role in virus translation in EV71-infected intestinal epithelial cells and that curcumin treatment decreases the phosphorylation of this enzyme. In addition, we show evidence that curcumin also limits viral translation in differentiated human intestinal epithelial cells. In summary, our data demonstrate the anti-EV71 properties of curcumin, suggesting that ingestion of this phytochemical may protect against enteroviral infections. PMID:29370243

Inhibition of EV71 by curcumin in intestinal epithelial cells.

Science.gov (United States)

Huang, Hsing-I; Chio, Chi-Chong; Lin, Jhao-Yin

2018-01-01

EV71 is a positive-sense single-stranded RNA virus that belongs to the Picornaviridae family. EV71 infection may cause various symptoms ranging from hand-foot-and-mouth disease to neurological pathological conditions such as aseptic meningitis, ataxia, and acute transverse myelitis. There is currently no effective treatment or vaccine available. Various compounds have been examined for their ability to restrict EV71 replication. However, most experiments have been performed in rhabdomyosarcoma or Vero cells. Since the gastrointestinal tract is the entry site for this pathogen, we anticipated that orally ingested agents may exert beneficial effects by decreasing virus replication in intestinal epithelial cells. In this study, curcumin (diferuloylmethane, C21H20O6), an active ingredient of turmeric (Curcuma longa Linn) with anti-cancer properties, was investigated for its anti-enterovirus activity. We demonstrate that curcumin treatment inhibits viral translation and increases host cell viability. Curcumin does not exert its anti-EV71 effects by modulating virus attachment or virus internal ribosome entry site (IRES) activity. Furthermore, curcumin-mediated regulation of mitogen-activated protein kinase (MAPK) signaling pathways is not involved. We found that protein kinase C delta (PKCδ) plays a role in virus translation in EV71-infected intestinal epithelial cells and that curcumin treatment decreases the phosphorylation of this enzyme. In addition, we show evidence that curcumin also limits viral translation in differentiated human intestinal epithelial cells. In summary, our data demonstrate the anti-EV71 properties of curcumin, suggesting that ingestion of this phytochemical may protect against enteroviral infections.

Inhibition of EV71 by curcumin in intestinal epithelial cells.

Directory of Open Access Journals (Sweden)

Hsing-I Huang

Full Text Available EV71 is a positive-sense single-stranded RNA virus that belongs to the Picornaviridae family. EV71 infection may cause various symptoms ranging from hand-foot-and-mouth disease to neurological pathological conditions such as aseptic meningitis, ataxia, and acute transverse myelitis. There is currently no effective treatment or vaccine available. Various compounds have been examined for their ability to restrict EV71 replication. However, most experiments have been performed in rhabdomyosarcoma or Vero cells. Since the gastrointestinal tract is the entry site for this pathogen, we anticipated that orally ingested agents may exert beneficial effects by decreasing virus replication in intestinal epithelial cells. In this study, curcumin (diferuloylmethane, C21H20O6, an active ingredient of turmeric (Curcuma longa Linn with anti-cancer properties, was investigated for its anti-enterovirus activity. We demonstrate that curcumin treatment inhibits viral translation and increases host cell viability. Curcumin does not exert its anti-EV71 effects by modulating virus attachment or virus internal ribosome entry site (IRES activity. Furthermore, curcumin-mediated regulation of mitogen-activated protein kinase (MAPK signaling pathways is not involved. We found that protein kinase C delta (PKCδ plays a role in virus translation in EV71-infected intestinal epithelial cells and that curcumin treatment decreases the phosphorylation of this enzyme. In addition, we show evidence that curcumin also limits viral translation in differentiated human intestinal epithelial cells. In summary, our data demonstrate the anti-EV71 properties of curcumin, suggesting that ingestion of this phytochemical may protect against enteroviral infections.

The total neutron cross-sections of 151Eu, 153Eu and Eu below 1 eV

International Nuclear Information System (INIS)

Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Ashry, A.; Hamouda, I.

1980-12-01

Total neutron cross-section measurements have been carried out for natural Eu and its stable isotopes in the energy range from 3 meV-1 eV. The measurements were performed using two time-of-flight spectrometers installed in front of two of the horizontal channels of the ET-RR-1 reactor. The following results have been obtained: sigmasub(α)( 151 Eu) = 9180+-150 b at 0.0253 eV; sigmasub(α)( 153 Eu) = 375+-20 b at 0.0253 eV; sigmasub(α)(Eu) = 4600+-120 b at 0.0253 eV

Fluoride salts as phase change materials for thermal energy storage in the temperature range 1000-1400 K

Science.gov (United States)

Misra, Ajay K.

1988-01-01

Eutectic compositions and congruently melting intermediate compounds in binary and ternary fluoride salt systems were characterized for potential use as latent heat of fusion phase change materials to store thermal energy in the temperature range 1000-1400 K. The melting points and eutectic compositions for many systems with published phase diagrams were experimentally verified and new eutectic compositions having melting points between 1000 and 1400 K were identified. Heats of fusion of several binary and ternary eutectics and congruently melting compounds were experimentally measured by differential scanning calorimetry. For a few systems in which heats of mixing in the melts have been measured, heats of fusion of the eutectics were calculated from thermodynamic considerations and good agreement was obtained between the measured and calculated values. Several combinations of salts with high heats of fusion per unit mass (greater than 0.7 kJ/g) have been identified for possible use as phase change materials in advanced solar dynamic space power applications.

SWR 1000: Efficient design for operational excellence

International Nuclear Information System (INIS)

Brettschuh, W.

2008-01-01

The SWR 1000 boiling water reactor (BWR) offers all of the advantages associated with an advanced plant design, i.e. excellent safety performance and competitive power generation costs, in the medium capacity range (1000-1250 MW). The economic efficiency of this medium-sized plant in comparison with large-capacity designs is achieved by using very simple passive safety equipment, simplified plant operating systems, and a very simple plant configuration. Systems engineering is thus optimized, reducing dependence on electrical and instrumentation and control (I and C) systems. The fuel assemblies deployed in the SWR 1000 core are enlarged from a 10 x 10 to a 12 x 12 rod array. This cuts down the total number of fuel assemblies in the core and hence also the number of control rods and control rod drives, as well as in-core neutron flux monitors. The design owes its competitiveness to the fact that investment, maintenance and fuel cycle costs are all lower. In addition, refueling outages are shorter, thanks to the reduced scope for outage activities. For example, there are no bolted reactor internal joints, and the SWR 1000 has a permanently installed reactor vessel-to-drywell seal. Replacement of in-core detectors is carried out from below, and does not affect the critical path of the outage. Furthermore all in-service -inspections (ISIs) on the reactor pressure vessel (RPV) and its nozzles can be undertaken from the outside, so that no extended ISI outages are necessary. As in existing plants, forced coolant circulation is utilized, ensuring problem-free startup and enabling plant operators to adjust power rapidly in the high power range (70%-100%). This is achieved without moving the control rods, and allows both spectral-shift and stretch-out operation. The considerable gains provided by forced coolant circulation, in terms of operational flexibility and fuel utilization, mean that the investment and maintenance costs of the pumps are covered within just a few

7 CFR 1000.91-1000.92 - [Reserved

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true [Reserved] 1000.91-1000.92 Section 1000.91-1000.92 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... Miscellaneous Provisions §§ 1000.91-1000.92 [Reserved] ...

Experimental-theoretical comparisons of 1/sup 1/S. -->. 3/sup 1/P differential magnetic sublevel cross sections for electron-helium scattering at 80 and 100 eV

Energy Technology Data Exchange (ETDEWEB)

Chutjian, A [Jet Propulsion Lab., Pasadena, Calif. (USA)

1976-07-11

Experimental normalized absolute differential cross sections (DCS) for the excitation 1/sup 1/S ..-->.. 3/sup 1/P in helium are reported at incident electron energies of 80 and 100 eV, and at scattering angles between 7/sup 0/ and 135/sup 0/. The measurements are combined with results of recent electron-photon coincidence studies, and absolute DCS for the excitation of the magnetic sublevels 3/sup 1/P/sub 0/ and 3/sup 1/Psub(+-1) are obtained. These experimental sublevel cross sections, and their sum, are compared with results of recent calculations in the multichannel eikonal and distorted-wave polarized-orbital theories.

Day-Ahead Energy Planning with 100% Electric Vehicle Penetration in the Nordic Region by 2050

DEFF Research Database (Denmark)

Liu, Zhaoxi; Wu, Qiuwei; Nielsen, Arne Hejde

2014-01-01

This paper presents the day-ahead energy planning of passenger cars with 100% electric vehicle (EV) penetration in the Nordic region by 2050. EVs will play an important role in the future energy systems which can both reduce the greenhouse gas (GHG) emission from the transport sector and provide...... demand side flexibility required by the smart grids. On the other hand, the EVs will increase the electricity consumption. In order to quantify the electricity consumption increase due to the 100% EV penetration in the Nordic region to facilitate the power system planning studies, the day-ahead energy...

Investigation of the sup 9 sup 3 Nb neutron cross-sections in resonance energy range

CERN Document Server

Grigoriev, Y V; Faikov-Stanchik, H; Ilchev, G; Kim, G N; Kitaev, V Ya; Mezentseva, Z V; Panteleev, T; Sinitsa, V V; Zhuravlev, B V

2001-01-01

The results of gamma-ray multiplicity spectra and transmission measurements for sup 9 sup 3 Nb in energy range 21.5 eV-100 keV are presented. Gamma spectra from 1 to 7 multiplicity were measured on the 501 m and 121 m flight paths of the IBR-30 using a 16-section scintillation detector with a NaI(Tl) crystals of a total volume of 36 l and a 16-section liquid scintillation detector of a total volume of 80 l for metallic samples of 50, 80 mm in diameter and 1, 1.5 mm thickness with 100% sup 9 sup 3 Nb. Besides, the total and scattering cross-section of sup 9 sup 3 Nb were measured by means batteries of B-10 and He-3 counters on the 124 m, 504 m and 1006 m flight paths of the IBR-30. Spectra of multiplicity distribution were obtained for resolved resonances in the energy region E=30-6000 eV and for energy groups in the energy region E=21.5 eV- 100 keV. They were used for determination of the average multiplicity, resonance parameters and capture cross-section in energy groups and for low-laying resonances of sup...

Directional uv photoemission from (100) and (110) molybdenum surfaces

DEFF Research Database (Denmark)

Cinti, R. C.; Khoury, E. Al; Chakraverty, B. K.

1976-01-01

A study of the (100) and (110) molybdenum surfaces by directional photoemission spectroscopy is presented. Energy distribution spectra formed by photoelectrons emitted normal to the surfaces have been measured for photon energies between 10.2 and 21.2 eV. The results are discussed in terms of cal......-transition and surface-emission processes. Two extra structures are interpreted in terms of surface states or resonances: on the (100) surface, 0.5 eV below EF; on the (110) surface, 4.5 eV below EF in the s-d hybridization gap....... of calculated band structure within the framework of the K∥-conservation assumption. A good agreement is found between the main features of the experimental spectra and the emission expected from the band structure along the corresponding symmetry line in the Brillouin zone, assuming essentially direct...

System Architecture Design for Electric Vehicle (EV) Systems

DEFF Research Database (Denmark)

Xu, Zhao; Wu, Qiuwei; Nielsen, Arne Hejde

2010-01-01

The electric vehicle (EV) system should fulfill the energy needs of EVs to meet the EV users’ driving requirements and enable the system service from EVs to support the power system operation with high penetration of renewable energy resources (RES) by providing necessary infrastructures. In orde...

Day-Ahead Energy Planning with 100% Electric Vehicle Penetration in the Nordic Region by 2050

Directory of Open Access Journals (Sweden)

Zhaoxi Liu

2014-03-01

Full Text Available This paper presents the day-ahead energy planning of passenger cars with 100% electric vehicle (EV penetration in the Nordic region by 2050. EVs will play an important role in the future energy systems which can both reduce the greenhouse gas (GHG emissions from the transport sector and provide the demand side flexibility required by smart grids. On the other hand, the EVs will increase the electricity consumption. In order to quantify the electricity consumption increase due to the 100% EV penetration in the Nordic region to facilitate the power system planning studies, the day-ahead energy planning of EVs has been investigated with different EV charging scenarios. Five EV charging scenarios have been considered in the energy planning analysis which are: uncontrolled charging all day, uncontrolled charging at home, timed charging, spot price based charging all day and spot price based charging at home. The demand profiles of the five charging analysis show that timed charging is the least favorable charging option and the spot priced based EV charging might induce high peak demands. The EV charging demand will have a considerable share of the energy consumption in the future Nordic power system.

A highly selective and wide range ammonia sensor—Nanostructured ZnO:Co thin film

International Nuclear Information System (INIS)

Mani, Ganesh Kumar; Rayappan, John Bosco Balaguru

2015-01-01

Graphical abstract: - Highlights: • Cobalt doped nanostructured ZnO thin films were spray deposited on glass substrates. • Co-doped ZnO film was highly selective towards ammonia than ethanol, methanol, etc. • The range of ammonia detection was improved significantly by doping cobalt in ZnO. - Abstract: Ammonia sensing characteristics of undoped and cobalt (Co)-doped nanostructured ZnO thin films were investigated. Polycrystalline nature with hexagonal wurtzite structure and high crystalline quality with dominant (0 0 2) plane orientation of Co-doped ZnO film were confirmed by the X-ray diffractogram. Scanning electron micrographs of the undoped film demonstrated the uniform deposition of sphere-shaped grains. But, smaller particles with no clear grain boundaries were observed for Co-doped ZnO thin film. Band gap values were found to be 3.26 eV and 3.22 eV for undoped and Co-doped ZnO thin films. Ammonia sensing characteristics of Co-doped ZnO film at room temperature were investigated in the concentration range of 15–1000 ppm. Variation in the sensing performances of Co-doped and pure ZnO thin films has been analyzed and compared

Towards a meaningful metric for the quantification of GHG emissions of electric vehicles (EVs)

International Nuclear Information System (INIS)

Manjunath, Archana; Gross, George

2017-01-01

A key motivator for wider deployment of electric vehicles (EVs) – vehicles that are fully powered by battery charged from grid electricity – is to bring about environmental cleanliness. This goal is based on the fact that EVs produce zero tailpipe emissioon the associated carbon emissins. However, the generation and transmission of the charge electricity produce emissions that are not explicitly accounted by current measurement metrics for EV greenhouse gas (GHG) emissions and as such, the notion of environmental cleanliness of EVs becomes questionable. In this paper, we propose a comprehensive metric to quantify the actual environmental impacts of EVs. The new metric that we call the electric vehicle emissions index (EVEI) captures CO_2 emissions in the electricity production to consumption stages. Our metric is the first that provides transparency in the comparison of total emissions among various EV models, as well as in the side-by-side comparison of an EV with a gasoline vehicle (GV). Illustrative results indicate that the actual environmental impacts of an EV may show wide spatial variations and in some case, these impacts may be even greater than that of GV. Such insights that the EVEI provides may be useful in a wide range of applications, particularly in policy and incentive formulation. - Highlights: • We propose the Electric Vehicle Emission Index (EVEI) metric. • EVEI indicates the EV environmental impacts w.r.t gasoline vehicles (GVs). • Fuel economy and resource mix are the major contributors to emissions. • Results indicate EVs may prove to be dirtier than GVs in certain areas of usage. • Insights may prove to be valuable to policy and incentive formulation.

Fit for competition with ``EVS `99``; Mit ``EVS `99`` fit fuer den Wettbewerb

Energy Technology Data Exchange (ETDEWEB)

Klawunn, K.H.; Wamhof, F. [Energieversorgung Suedsachsen AG, Chemnitz (Germany)

1998-05-01

The Energieversorgung Suedsachsen AG (EVS AG) located in Chemnitz faces up to the challenges of the competitive energy market. The company launched the project ``EVS `99`` in order to achieve the essential strategic goals: increase customer loyalty, concentrate on the core business, open up new operating areas, improve the core competences. This comprehensive business re-engineering project is intended to realise by the end of the business year 1997/98 an optimisation of all essential business processes, which are to focus on customer needs, establishment of an efficient, customer-oriented organisation in line with the strategy, and design of the required management and control systems. The technical and communication systems will be based on the SAP R/3 software in order to fully exploit the optimisation potentials. (orig./CB) [Deutsch] Die Energieversorgung Suedsachsen AG (EVS AG) in Chemnitz stellt sich aktiv den Herausforderungen des Wettbewerbs. Um die strategischen Unternehmensziele Erhoehung der Kundenbindung, Konzentration auf das Kerngeschaeft, Erschliessung neuer Geschaeftsfelder und Verbesserung der Kernkompetenzen zu erreichen, wurde das Projekt `EVS `99` initiiert. Durch dieses umfassende Business-Reengineering-Projekt wird bis Ende des Geschaeftsjahres 1997/98 die Optimierung aller wesentlichen Geschaeftsprozesse und deren Ausrichtung an den Kundenanforderungen, der Aufbau einer strategiekonformen, effizienten, kundenorientierten Organisation und die Gesaltung anforderungsgerechter Fuehrungs- und Steuerungssysteme realisiert. Begleitend wird die Software SAP R/3 im Unternehmen eingefuehrt, um umfassend, d.h. bereichsuebergreifend, alle Optimierungspotentiale zu nutzen. (orig./RHM)

Development of battery management systems (BMS for electric vehicles (EVs in Malaysia

Directory of Open Access Journals (Sweden)

Salehen P.M.W.

2017-01-01

Full Text Available Battery Management Systems (BMS is an electronic devices component, which is a vital fundamental device connected between the charger and the battery of the hybrid or electric vehicle (EV systems. Thus, BMS significantly enable for safety protection and reliable battery management by performing of monitoring charge control, state evaluation, reporting the data and functionalities cell balancing. To date, 97.1% of Malaysian CO2 emissions are mainly caused by transportation activities and the numbers will keep rising as numbers of registered car increase close up to 1 million yearly; double the amounts in the last two decades. The uncertainty of a battery’s performance poses a challenge to predict the extended range of EVs, which need BMS implementation of optimization of optimum power management. Hence, using MATLAB/SIMULINK software is one of the potential methods of BMS optimization with power generated by Hybrid Energy Storage system of lithium-ion battery. Therefore, this paper address through reviewing previous literatures initially focuses on the BMS optimization for EVs (car in Malaysia as prognostic technology model improvement on performance management of EVs.

HiggsToFourLeptonsEV in the ATLAS EventView Analysis Framework

CERN Document Server

Lagouri, T; Del Peso, J

2008-01-01

ATLAS is one of the four experiments at the Large Hadron Collider (LHC) at CERN. This experiment has been designed to study a large range of physics topics, including searches for previously unobserved phenomena such as the Higgs Boson and super-symmetry. The physics analysis package HiggsToFourLeptonsEV for the Standard Model (SM) Higgs to four leptons channel with ATLAS is presented. The physics goal is to investigate with the ATLAS detector, the SM Higgs boson discovery potential through its observation in the four-lepton (electron and muon) final state. HiggsToFourLeptonsEV is based on the official ATLAS software ATHENA and the EventView (EV) analysis framework. EventView is a highly flexible and modular analysis framework in ATHENA and it is one of several analysis schemes for ATLAS physics user analysis. At the core of the EventView is the representative "view" of an event, which defines the contents of event data suitable for event-level physics analysis. The HiggsToFourLeptonsEV package, presented in ...

Real-Time Forecasting of EV Charging Station Scheduling for Smart Energy Systems

Directory of Open Access Journals (Sweden)

Bharatiraja Chokkalingam

2017-03-01

Full Text Available The enormous growth in the penetration of electric vehicles (EVs, has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate user’s “range anxiety”. The existing charging stations fail to adopt power provision, allocation and scheduling management. To improve the existing charging infrastructure, data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on the road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

Optical band gap of ZnO thin films deposited by electron beam evaporation

International Nuclear Information System (INIS)

Nadeem, M. Y.; Ali, S. L.; Wasiq, M. F.; Rana, A. M.

2006-01-01

Optical band gap of ZnO thin films deposited by electron beam evaporation at evaporation rates ranging 5 As/sup -1/ to 15 As /sup -1/ and thickness ranging 1000A to 3000A is presented. Deposited films were annealed at 573K for one and half hour. The variations in the optical band gap were observed and showed decreasing behavior from 3.15 eV, 3.05 eV, from 3.18 eV to 3.10 eV and from 3.19 eV to 3.18 eV for films with respective thickness 1000A, 2000 A, 3000 A on increasing the evaporation rate from 5 As/sup-1/ to As/sup -1/ by keeping thickness constant. (author)

Calculated Performance Of The Variable-Polarization Undulator Upgrade To The Daresbury SRS Soft X-Ray Undulator Beamline

International Nuclear Information System (INIS)

Roper, Mark D.; Bird, Daniel T.

2004-01-01

The soft x-ray beamline 5U1 on the Daresbury Laboratory SRS currently uses a planar undulator, producing linearly polarized radiation in the range 100 to 1000 eV. The undulator is soon to be replaced by a variable-polarization device of the Apple II design. The aim is to produce circularly polarized light in the energy range 265 to 1000 eV, covering the K-edges of C, N and O, and the first row transition element L-edges. This will greatly enhance the provision of circularly polarized soft-x-rays on the SRS and open up new opportunities for experimenters. The device will also produce linear polarization with a selectable angle of polarization with respect to the orbit plane, which is currently unavailable on the SRS. In order to provide the coverage over this energy range, we are exploiting the relatively large emittance of the SRS to allow us to use the second and third harmonics even in circular polarization mode. This paper presents the expected beamline output in various polarization modes and the predicted degree of polarization

The total neutron cross-sections of 151Eu, 153Eu and Eu below 1 eV

International Nuclear Information System (INIS)

Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Ashry, A.; Hamouda, I.

1981-01-01

Total neutron cross-section measurements have been carried out for natural Eu and its stable isotopes in the energy range from 3 meV to 1 eV. The measurements were performed using two time-of-flight spectrometers installed in front of two of the horizontal channels of the ET-RR-1 reactor. The following results have been obtained: sigmasub(a) ( 151 Eu) = (9180 +- 150) b at 0.0253 eV, sigmasub(s) ( 153 Eu) = (375 +- 20) b at 0.0253 eV, sigmasub(d) (Eu) = (4600 +- 120) b at 0.0253 eV. The contribution of the resonance to the total neutron cross-sections, in the thermal region, was calculated using the single-level Breit-Wigner formula. (orig.)

Actual preferences for EV households in Denmark and Sweden

DEFF Research Database (Denmark)

Jensen, Anders Fjendbo; Haustein, Sonja; Cherchi, Elisabetta

, as the EV market is still quite immature in most countries, lack of data on EV users is a common problem for researchers. Data on EV purchase and use have thus often been collected by means of data from intentional statements (see e.g. Bühler et al. 2014), stated preferences (see e.g. Bunch et al. 1993......; Hidrue et al. 2011; Jensen et al. 2014) and EV vehicle trials (Golob & Gould 1998; Franke & Krems 2013; Jensen et al. 2014). While such studies have provided important insight into various areas of the EV market, the fact that the results are not based on actual behaviour means that they are subject...... to a high degree of uncertainty. Being the global EV market forerunner, Norway has a better foundation for studying the EV market based on actual EV owners. On these grounds, Klöckner et al. (2013), studied differences in car use between EV and conventional vehicle (CV) users. Also in Norway, Mersky et al...

Luminescence excitation characteristics of Ca-, Na- and K-aluminosilicates (feldspars), in the stimulation range 20-500 eV: optical detection of XAS

CERN Document Server

Poolton, N R J; Quinn, F M; Pantos, E; Andersen, C E; Bøtter-Jensen, L; Johnsen, O; Murray, A S

2003-01-01

We demonstrate that the visible/UV luminescence from common feldspar crystals (NaAlSi sub 3 O sub 8 , KAlSi sub 3 O sub 8 and CaAl sub 2 Si sub 2 O sub 8) can be used to detect detailed L-edge and associated near-edge absorption structure of the main constituent atoms (Ca, K, Na, Al, Si), when exciting in the energy range 20-500 eV. Comparisons of the spectral features are drawn with similar measurements made on the associated materials SiO sub 2 , Al sub 2 O sub 3 and CaCO sub 3. The potential for using optically detected x-ray absorption spectroscopy as a method for identifying the luminescent components of mixed mineral samples is considered.

Battery management systems (BMS) optimization for electric vehicles (EVs) in Malaysia

Science.gov (United States)

Salehen, P. M. W.; Su'ait, M. S.; Razali, H.; Sopian, K.

2017-04-01

Following the UN Climate Change Conference 2009 in Copenhagen, Denmark, Malaysia seriously committed on "Go Green" campaign with the aim to reduce 40% GHG emission by the year 2020. Therefore, the National Green Technology Policy has been legalised in 2009 with transportation as one of its focused sectors, which include hybrid (HEVs), electric vehicles (EVs) and fuel cell vehicles with the purpose of to keep up with the worst scenario. While the number of registered cars has been increasing by 1 million yearly, the amount has doubled in the last two decades. Consequently, CO2 emission in Malaysia reaches up to 97.1% and will continue to increase mainly due to the activities in the transportation sector. Nevertheless, Malaysia is now moving towards on green car which battery-based EVs. This type of transportation mainly needs power performance optimization, which is controlled by the Batteries Management System (BMS). BMS is an essential module which leads to reliable power management, optimal power performance and safe vehicle that lead back for power optimization in EVs. Thus, this paper proposes power performance optimization for various setups of lithium-ion cathode with graphene anode using MATLAB/SIMULINK software for better management performance and extended EVs driving range.

Eesti esinaivisti 100. sünniaastapäev / Tiiu Männiste

Index Scriptorium Estoniae

Männiste, Tiiu, 1959-

2000-01-01

Paul Kondase 100. sünniaastapäeva puhul tema maalide näitus Viljandi kunstisaalis. Avamisel demonstreeris Mark Soosaar oma filmi "Pühapäevamaalijad". Kilpkonna galeriis näitusel "Veel naiviste" Joan (?Joann) Sõstra (1913-1992) (puuskulptuurid), Osvald Raba (1909-1996) ja Arnold Vihmandi (1912) looming.

Delivery of Human EV71 Receptors by Adeno-Associated Virus Increases EV71 Infection-Induced Local Inflammation in Adult Mice

Directory of Open Access Journals (Sweden)

Hung-Bo Hsiao

2014-01-01

Full Text Available Enterovirus71 (EV71 is now recognized as an emerging neurotropic virus in Asia and one major causative agent of hand-foot-mouth diseases (HFMD. However potential animal models for vaccine development are limited to young mice. In this study, we used an adeno-associated virus (AAV vector to introduce the human EV71 receptors P-selectin glycoprotein ligand-1 (hPSGL1 or a scavenger receptor class-B member-2 (hSCARB2 into adult ICR mice to change their susceptibility to EV71 infection. Mice were administered AAV-hSCARB2 or AAV-hPSGL1 through intravenous and oral routes. After three weeks, expression of human SCARB2 and PSGL1 was detected in various organs. After infection with EV71, we found that the EV71 viral load in AAV-hSCARB2- or AAV-hPSGL1-transduced mice was higher than that of the control mice in both the brain and intestines. The presence of EV71 viral particles in tissues was confirmed using immunohistochemistry analysis. Moreover, inflammatory cytokines were induced in the brain and intestines of AAV-hSCARB2- or AAV-hPSGL1-transduced mice after EV71 infection but not in wild-type mice. However, neurological disease was not observed in these animals. Taken together, we successfully infected adult mice with live EV71 and induced local inflammation using an AAV delivery system.

PHEV/EV Li-Ion Battery Second-Use Project (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Neubauer, J.; Pesaran, A.

2010-04-01

Accelerated development and market penetration of plug-in hybrid electric vehicles (PHEVs) and electric vehicles (Evs) are restricted at present by the high cost of lithium-ion (Li-ion) batteries. One way to address this problem is to recover a fraction of the battery cost via reuse in other applications after the battery is retired from service in the vehicle, if the battery can still meet the performance requirements of other energy storage applications. In several current and emerging applications, the secondary use of PHEV and EV batteries may be beneficial; these applications range from utility peak load reduction to home energy storage appliances. However, neither the full scope of possible opportunities nor the feasibility or profitability of secondary use battery opportunities have been quantified. Therefore, with support from the Energy Storage activity of the U.S. Department of Energy's Vehicle Technologies Program, the National Renewable Energy Laboratory (NREL) is addressing this issue. NREL will bring to bear its expertise and capabilities in energy storage for transportation and in distributed grids, advanced vehicles, utilities, solar energy, wind energy, and grid interfaces as well as its understanding of stakeholder dynamics. This presentation introduces NREL's PHEV/EV Li-ion Battery Secondary-Use project.

Optical properties of InGaN thin films in the entire composition range

Science.gov (United States)

Kazazis, S. A.; Papadomanolaki, E.; Androulidaki, M.; Kayambaki, M.; Iliopoulos, E.

2018-03-01

The optical properties of thick InGaN epilayers, with compositions spanning the entire ternary range, are studied in detail. High structural quality, single phase InxGa1-xN (0001) films were grown heteroepitaxially by radio-frequency plasma assisted molecular-beam epitaxy on freestanding GaN substrates. Their emission characteristics were investigated by low temperature photoluminescence spectroscopy, whereas variable angle spectroscopic ellipsometry was applied to determine the complex dielectric function of the films, in the 0.55-4.0 eV photon range. Photoluminescence lines were intense and narrow, in the range of 100 meV for Ga-rich InGaN films (x 0.6). The composition dependence of the strain-free emission energy was expressed by a bowing parameter of b = 2.70 ± 0.12 eV. The films' optical dielectric function dispersion was obtained by the analysis of the ellipsometric data employing a Kramers-Kronig consistent parameterized optical model. The refractive index dispersion was obtained for alloys in the entire composition range, and the corresponding values at the band edge show a parabolic dependence on the InN mole fraction expressed by a bowing parameter of b = 0.81 ± 0.04. The bowing parameter describing the fundamental energy bandgap was deduced to be equal to 1.66 ± 0.07 eV, consistent with the ab initio calculations for statistically random (non-clustered) InGaN alloys.

The happy medium: a useful property of solutions from EVS methodology

International Nuclear Information System (INIS)

Hoppe, F.M.; Weaver, K.

2013-01-01

EVS methodology is a statistical approach developed to deal with problems in which there is a need to select defensible licensing values for selected variables, while taking account of a potentially complex set of error terms arising from different sources. The name EVS arises from 'extreme value statistics', since the maxima and minima of random variables arise naturally for the problems of interest. Two problems to which the approach has been applied are compliance with regulatory limits on maximum channel powers, and the selection of trip set points for the Neutron Overpower Protection (NOP) system. In the first of these problems, the limiting channel power is specified by the regulator (i.e. it is known with 100% certainty), whereas in the second problem no value for the trip setpoint can be known with certainty apart from the trivial case which would force a reactor to be shut down permanently. (author)

SWR 1000: A Next-Generation Boiling Water Reactor Ready for Deployment

International Nuclear Information System (INIS)

Brettschuh, W.

2006-01-01

The latest developments in nuclear power generation technology mainly concern large-capacity plants in the 1550 -1600 MW range, or very small plants (100 - 350 MW). The SWR 1000 boiling water reactor (BWR), by contrast, offers all of the advantages of an advanced plant design, with excellent safety performance and competitive power generation costs, in the medium-capacity range (1000 - 1250 MW). The SWR 1000 design is particularly suitable for countries whose power systems do not include any large power plants. The economic efficiency of this medium-sized plant in comparison with large-capacity designs is achieved by deploying very simple passive safety equipment, simplified systems for plant operation, and a very simple plant configuration in which systems engineering is optimized and dependence on electrical and instrumentation and control (IandC) systems is reduced. In addition, systems and components that require protection against natural and external man-made hazards are accommodated in such a way that as few buildings as possible have to be designed to withstand the loads from such events. The fuel assemblies to be deployed in the SWR 1000 core, meanwhile, have been enlarged from a 10x10 rod array to a 12x12 array. This reduces the total number of fuel assemblies in the core and thus also the number of control rods and control rod drives, as well as in-core neutron flux monitors. The design owes its competitiveness to the fact that investment costs, maintenance costs and fuel cycle costs are all lower. In addition, refueling outages are shorter, thanks to the reduced scope of outage activities. The larger fuel assemblies have been extensively and successfully tested, as have all of the other new components and systems incorporated into the plant design. As in existing plants, the forced coolant circulation method is deployed, ensuring problem-free start-up, and enabling plant operators to adjust power rapidly in the high power range (70%-100%) without moving

An EV Charging Scheduling Mechanism Based on Price Negotiation

Directory of Open Access Journals (Sweden)

Baocheng Wang

2018-05-01

Full Text Available Scheduling EV user’s charging behavior based on charging price and applying renewable energy resources are the effective methods to release the load pressure of power grids brought about by the large-scale popularity of electric vehicles (EVs. This paper presents a novel approach for EV charging scheduling based on price negotiation. Firstly, the EV charging system framework based on price negotiation and renewable energy resources is discussed. Secondly, the price negotiation model is presented, including the initial price models and the conditions of transactions. Finally, an EV charging scheduling mechanism based on price negotiation (CSM-PN, including the price adjustment strategies of both the operator and EV users is proposed to seek a final transaction during multi-round price negotiation. Simulation results show that this novel approach can effectively improve the charging station operator’s income, reduce the EV users’ costs, and balance the load of the power grid while improving the efficiency of the EV charging system.

Effect of swift heavy ion irradiation on deep levels in Au /n-Si (100) Schottky diode studied by deep level transient spectroscopy

Science.gov (United States)

Kumar, Sandeep; Katharria, Y. S.; Kumar, Sugam; Kanjilal, D.

2007-12-01

In situ deep level transient spectroscopy has been applied to investigate the influence of 100MeV Si7+ ion irradiation on the deep levels present in Au/n-Si (100) Schottky structure in a wide fluence range from 5×109to1×1012ions cm-2. The swift heavy ion irradiation introduces a deep level at Ec-0.32eV. It is found that initially, trap level concentration of the energy level at Ec-0.40eV increases with irradiation up to a fluence value of 1×1010cm-2 while the deep level concentration decreases as irradiation fluence increases beyond the fluence value of 5×1010cm-2. These results are discussed, taking into account the role of energy transfer mechanism of high energy ions in material.

High image quality sub 100 picosecond gated framing camera development

International Nuclear Information System (INIS)

Price, R.H.; Wiedwald, J.D.

1983-01-01

A major challenge for laser fusion is the study of the symmetry and hydrodynamic stability of imploding fuel capsules. Framed x-radiographs of 10-100 ps duration, excellent image quality, minimum geometrical distortion (< 1%), dynamic range greater than 1000, and more than 200 x 200 pixels are required for this application. Recent progress on a gated proximity focused intensifier which meets these requirements is presented

Evidence-Based Clinical Use of Nanoscale Extracellular Vesicles in Nanomedicine.

Science.gov (United States)

Fais, Stefano; O'Driscoll, Lorraine; Borras, Francesc E; Buzas, Edit; Camussi, Giovanni; Cappello, Francesco; Carvalho, Joana; Cordeiro da Silva, Anabela; Del Portillo, Hernando; El Andaloussi, Samir; Ficko Trček, Tanja; Furlan, Roberto; Hendrix, An; Gursel, Ihsan; Kralj-Iglic, Veronika; Kaeffer, Bertrand; Kosanovic, Maja; Lekka, Marilena E; Lipps, Georg; Logozzi, Mariantonia; Marcilla, Antonio; Sammar, Marei; Llorente, Alicia; Nazarenko, Irina; Oliveira, Carla; Pocsfalvi, Gabriella; Rajendran, Lawrence; Raposo, Graça; Rohde, Eva; Siljander, Pia; van Niel, Guillaume; Vasconcelos, M Helena; Yáñez-Mó, María; Yliperttula, Marjo L; Zarovni, Natasa; Zavec, Apolonija Bedina; Giebel, Bernd

2016-04-26

Recent research has demonstrated that all body fluids assessed contain substantial amounts of vesicles that range in size from 30 to 1000 nm and that are surrounded by phospholipid membranes containing different membrane microdomains such as lipid rafts and caveolae. The most prominent representatives of these so-called extracellular vesicles (EVs) are nanosized exosomes (70-150 nm), which are derivatives of the endosomal system, and microvesicles (100-1000 nm), which are produced by outward budding of the plasma membrane. Nanosized EVs are released by almost all cell types and mediate targeted intercellular communication under physiological and pathophysiological conditions. Containing cell-type-specific signatures, EVs have been proposed as biomarkers in a variety of diseases. Furthermore, according to their physical functions, EVs of selected cell types have been used as therapeutic agents in immune therapy, vaccination trials, regenerative medicine, and drug delivery. Undoubtedly, the rapidly emerging field of basic and applied EV research will significantly influence the biomedicinal landscape in the future. In this Perspective, we, a network of European scientists from clinical, academic, and industry settings collaborating through the H2020 European Cooperation in Science and Technology (COST) program European Network on Microvesicles and Exosomes in Health and Disease (ME-HAD), demonstrate the high potential of nanosized EVs for both diagnostic and therapeutic (i.e., theranostic) areas of nanomedicine.

Properties of the 4.45 eV optical absorption band in LiF:Mg, Ti

International Nuclear Information System (INIS)

Nail, I.; Oster, L.; Horowitz, Y. S.; Biderman, S.; Belaish, Y.

2006-01-01

The optical absorption (OA) and thermoluminescence (TL) of dosimetric LiF:Mg,Ti (TLD-100) as well as nominally pure LiF single crystal have been studied as a function of irradiation dose, thermal and optical bleaching in order to investigate the role of the 4.45 eV OA band in low temperature TL. Computerised deconvolution was used to resolve the absorption spectrum into individual gaussian bands and the TL glow curve into glow peaks. Although the 4.45 eV OA band shows thermal decay characteristics similar to the 4.0 eV band its dose filling constant and optical bleaching properties suggest that it cannot be associated with the TL of composite peaks 4 or 5. Its presence in optical grade single crystal LiF further suggests that it is an intrinsic defect or possibly associated with chance impurities other than Mg, Ti. (authors)

0.1–2000 eV electron impact cross sections for dichlorine monoxide

Energy Technology Data Exchange (ETDEWEB)

Goswami, Biplab; Gupta, Dhanoj; Antony, Bobby, E-mail: bka.ism@gmail.com

2014-03-01

Highlights: • Quantum mechanical models were used to find TCS for e-Cl{sub 2}O from 0.1 to 2000 eV. • R-matrix method at low energies (<13 eV) and SCOP at high energies (13–2000 eV). • Besides TCS, DCS, excitation cross section and momentum transfer CS also predicted. • R-matrix method identifies resonances with a possibility of DEA formation. • Resonance detected at 1.88 eV is associated with Cl{sub 2}O{sup −} anion formation. - Abstract: Scattering dynamics of dichlorine monoxide (Cl{sub 2}O) molecule by electron impact is investigated as a function of electron energy and scattering angle. Electron impact total cross sections for Cl{sub 2}O over an extensive range of impact energies from 0.1 to 2000 eV are reported in this article. Below the ionization threshold of the target, the ab initio R-matrix method and above this incident energy spherical complex optical potential formalism are used for cross section calculation. The total cross section obtained from both theories merges smoothly at the overlapping energy. The resonances obtained using DZP basis sets are located at 1.883, 3.592, 5.205 and 7.326, 8.206, 8.301, 8.452, 9.369 eV and that with 6-31G* basis sets are identified at 1.944, 3.566, 5.183, 5.261, 5.658, 8.738 and 9.187 eV with the possibility of negative ions formation. This is the first attempt to calculate the differential, and momentum transfer cross sections for Cl{sub 2}O molecule.

Study of nitrogen solubility in multicomponent iron alloys at its pressure in gaseous phase up to 1000kPa

International Nuclear Information System (INIS)

Pomarin, Yu.M.; Grigorenko, G.M.; Latash, Yu.V.; Kanibolotskij, S.A.

1983-01-01

A facility in which metal is melted in a weighed state and nitrogen partical pressure during relting may be charge from 0 to 1000 kPa is developed to investigate nitrogen solubility is liquim metals and alloys. Investigation of nitrogen solubility was performed using samples of 03Kh25N5AM3 steel and Kh20N5, Kh20N10, Kh40N10, Kh40N20 alloys. Positive deflection of [N]=f(√Psub(Nsub(2))) dependence from the Henry law is shown to be observed in the Kh40N10 alloy in the 100-1000 kPa pressure range. In this case the vatue of positive deflection decreases with temperature growth and at T=2273 K nitrogen solubility in the alloy submits to the law of square root. An equation permitting to calculate nitrogen solubility in alloys of Fe-Cr-Ni and Fe-Cr-Mn systems in the 0 to 1000 kPa range of nitrogen partial pressures is obtained

DDG-1000 Zumwalt Class Destroyer (DDG-1000)

Science.gov (United States)

2015-12-01

Selected Acquisition Report (SAR) RCS: DD-A&T(Q&A)823-197 DDG 1000 Zumwalt Class Destroyer (DDG 1000 ) As of FY 2017 President’s Budget Defense...Acquisition Management Information Retrieval (DAMIR) March 23, 2016 15:17:06 UNCLASSIFIED DDG 1000 December 2015 SAR March 23, 2016 15:17:06...Requirements Document OSD - Office of the Secretary of Defense O&S - Operating and Support PAUC - Program Acquisition Unit Cost DDG 1000 December 2015 SAR

Theoretical investigation of image states of the hydrogen covered Cu (100)

International Nuclear Information System (INIS)

Steslicka, M.; Zagorski, M.; Jurczyszyn, L.

1987-08-01

A model of atomic hydrogen covered Cu(100) is presented and the calculated energy spectrum of localized electronic states in the X gap of Cu(100) is discussed. These states form a series of unoccupied adsorption image states (for n α = 2,3,...) lying below the vacuum level V 0 and having energies E nα which satisfy the formula E nα = V 0 - 10/n n 2 (eV). The lowest state (n α = 1) is expected to lie about 5.5 (eV) below Fermi level. (author). 19 refs, 6 figs, 1 tab

Total neutron cross-sections of /sup 151/Eu, /sup 153/Eu and Eu below 1 eV

Energy Technology Data Exchange (ETDEWEB)

Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Ashry, A.; Hamouda, I.

1981-01-01

Total neutron cross-section measurements have been carried out for natural Eu and its stable isotopes in the energy range from 3 meV to 1 eV. The measurements were performed using two time-of-flight spectrometers installed in front of two of the horizontal channels of the ET-RR-1 reactor. The following results have been obtained: sigmasub(a) (/sup 151/Eu) = (9180 +- 150) b at 0.0253 eV, sigmasub(s) (/sup 153/Eu) = (375 +- 20) b at 0.0253 eV, sigmasub(d) (Eu) = (4600 +- 120) b at 0.0253 eV. The contribution of the resonance to the total neutron cross-sections, in the thermal region, was calculated using the single-level Breit-Wigner formula.

Rotational excitation of N2 by electron impact: 1-4 eV

International Nuclear Information System (INIS)

Wong, S.F.; Dube, L.

1978-01-01

Rotational and rotational-vibrational (v = 0 → 1) excitation in N 2 have been studied with a crossed-beam electron-impact apparatus. In the energy range 1-4 eV, the elastic and vibrational energy-loss peaks show large rotational broadening compared with the apparatus profile (full width at half-maximum, 18 meV). The branching ratios for rotational transitions with Δj = 0, +- 2, +- 4 are obtained with a line-shape analysis applied to the energy-loss profiles. The results for rotational-vibrational excitation at 2.27 eV and scattering angles 30-90 0 are in good agreement with the calculations using the resonant dπ waves and the rotational impulse approximation. The corresponding results for pure rotational excitation show that the branches with Δj = +- 2 and +- 4 are predominantly excited via resonances, while the branch with Δj = 0 contains a large contribution from direct scattering. The absolute rotational cross sections for Δj = +- 4 are measured; they exhibit a large magnitude (10 -16 cm 2 ) and peak and valley structures in the 1-4 eV range, reminiscent of well-known resonant vibrational excitation. The energy dependence and the absolute magnitude of the rotational cross sections for Δj = +- 4 can be understood in terms of a ''boomerang'' calculation. A comparison of the experiment with the relevant theoretical calculations is made

Evaluation of 500- and 1,000-mg doses of ciprofloxacin for the treatment of chancroid.

Science.gov (United States)

Bodhidatta, L; Taylor, D N; Chitwarakorn, A; Kuvanont, K; Echeverria, P

1988-01-01

A randomized, double-blind study was performed comparing ciprofloxacin in a 500-mg single dose with 1,000 mg (500-mg doses given 12 h apart) for the treatment of chancroid in Thailand. Haemophilus ducreyi was isolated from 87 (48%) of 180 men with a clinical diagnosis of chancroid. For men with ulcers that were culture positive for H. ducreyi, rates of cure were 100% in the 500-mg group and 98% in the 1,000-mg group. For men with ulcers that were culture negative for H. ducreyi, rates of cure were 93% in the 500-mg group and 96% in the 1,000-mg group. The MIC of ciprofloxacin for 50% of isolates among 85 isolates of H. ducreyi was 0.007 micrograms/ml (range, 0.002 to 0.03 micrograms/ml). No significant adverse effects were detected in either group. These data indicate that both of these treatment regimens are equally effective therapies for chancroid in Thailand. PMID:3293526

Excitons and continuum transitions of rubidium halides in the 10 - 26 eV photon energy range at low temperatures

International Nuclear Information System (INIS)

Zierau, W.; Skibowski, M.

1975-04-01

The reflection spectra of RbCl, RbBr and RbI single crystals were investigated for temperatures between 300 K and 8 K in order to study excitations from the Rb + 4p level (> approximately 16 eV) as well as the higher continuum transitions from the valence band (> approximately 10 eV). The measurements were performed by use of the synchrotron radiation of DESY. The sensitivity for detecting details of the fine structure was increased by simultaneously measuring the wavelength modulated spectra. The experimental procedure is briefly described. New spectral features have been resolved for the exciton multiplets from the Rb + 4p level. They are discussed in light of the predictions of a recent model for the Rb + 4p excitons based on ligand field theory. The continuum transitions associated with the valence band and the Rb + 4p level show characteristic structure which is compared with calculations of the joint density of states. (orig.) [de

Usefulness of 1000-Hz probe tone in tympanometry according to age in Korean infants.

Science.gov (United States)

Park, Mina; Han, Kyu-Hee; Jung, Hyunseo; Kim, Mee-Hee; Chang, Hyun-Kyung; Kim, Shin Hye; Park, Moo Kyun; Lee, Jun Ho

2015-01-01

Numerous studies have shown the superiority of a 1000-Hz frequency probe tone for evaluating the middle ear status of infants. However, most of these studies examined Caucasian populations. This study validated the 1000-Hz probe tone and evaluated the age at which it should be used in Korean infants. Data from 83 infants (43 males, 40 females; mean age 9.2±6.2 (range 1-30) months, 165 ears) were analyzed. Tympanograms were classified according to Baldwin's modification of the method of Marchant et al. and correlated with results based on combined diagnostic tests, including an endoscopic examination of the tympanic membrane, myringotomy findings, and the air and bone conduction auditory brainstem response (ABR) thresholds. Data were analyzed in five age groups, each covering a 3-month range. The traces were measured for both 226- and 1000-Hz probe tones. The sensitivity and specificity for the different age groups were also determined. For the 226-Hz probe tone, the tympanograms showed normal traces for most ears with otitis media effusions in infants younger than 12 months. By contrast, the tympanograms using the 1000-Hz probe tone showed abnormal traces in most of the infants with otitis media effusions in all age groups. In infants with no otitis media effusion, the tympanograms using both 226- and 1000-Hz probe tones were interpreted as normal in most cases in all age groups. In infants younger than 12 months, the sensitivity of the 226-Hz probe tone was very low (0-6.6%), whereas that of the 1000-Hz probe tone was very high (90-100%). In infants older than 13 months, however, the sensitivities of the 226- and 1000-Hz probe tones were 76.2% and 85.7%, respectively. Regarding specificity, the difference between the two probe tones was not significant for any age group. This study confirmed the superiority of the 1000-Hz probe tone for evaluating the middle ear in infants. We recommend using a 1000-Hz probe tone at least up to the age of 12 months for Korean

SWR 1000: An Advanced, Medium-Sized Boiling Water Reactor, Ready for Deployment

International Nuclear Information System (INIS)

Brettschuh, Werner

2006-01-01

The latest developments in nuclear power generation technology mainly concern large-capacity plants in the 1550 -1600 MW range, or very small plants (100 - 350 MW). The SWR 1000 boiling water reactor (BWR), by contrast, offers all of the advantages of an advanced plant design, with excellent safety performance and competitive power generation costs, in the medium-capacity range (1000 - 1250 MW). The SWR 1000 is particularly suitable for countries whose power systems are not designed for large-capacity generating facilities. The economic efficiency of this medium-sized plant in comparison with large-capacity designs is achieved by deploying very simple passive safety equipment, simplified systems for plant operation, and a very simple plant configuration in which systems engineering is optimized and dependence on electrical and instrumentation and control (I and C) systems is reduced. In addition, systems and components that require protection against natural and external man-made hazards are accommodated in such a way that as few buildings as possible have to be designed to withstand the loads from such events. The fuel assemblies to be deployed in the SWR 1000 core, meanwhile, have been enlarged from a 10 x 10 rod array to a 12 x 12 array. This reduces the total number of fuel assemblies in the core and thus also the number of control rods and control rod drives, as well as in-core neutron flux monitors. The design owes its competitiveness to the fact that investment costs, maintenance costs and fuel cycle costs are all lower. In addition, refueling outages are shorter, thanks to the reduced scope of outage activities. The larger fuel assemblies have been extensively and successfully tested, as have all of the other new components and systems incorporated into the plant design. As in existing plants, the forced coolant circulation method is deployed, ensuring problem-free startup, and enabling plant operators to adjust power rapidly in the high power range (70%-100

Enumeration Verification System (EVS)

Data.gov (United States)

Social Security Administration — EVS is a batch application that processes for federal, state, local and foreign government agencies, private companies and internal SSA customers and systems. Each...

A first principle study for the adsorption and absorption of carbon atom and the CO dissociation on Ir(100) surface

Energy Technology Data Exchange (ETDEWEB)

Erikat, I. A., E-mail: ihsanas@yahoo.com [Department of Physics, Jerash University, Jerash-26150 (Jordan); Hamad, B. A. [Department of Physics, The University of Jordan, Amman-11942 (Jordan)

2013-11-07

We employ density functional theory to examine the adsorption and absorption of carbon atom as well as the dissociation of carbon monoxide on Ir(100) surface. We find that carbon atoms bind strongly with Ir(100) surface and prefer the high coordination hollow site for all coverages. In the case of 0.75 ML coverage of carbon, we obtain a bridging metal structure due to the balance between Ir–C and Ir–Ir interactions. In the subsurface region, the carbon atom prefers the octahedral site of Ir(100) surface. We find large diffusion barrier for carbon atom into Ir(100) surface (2.70 eV) due to the strong bonding between carbon atom and Ir(100) surface, whereas we find a very small segregation barrier (0.22 eV) from subsurface to the surface. The minimum energy path and energy barrier for the dissociation of CO on Ir(100) surface are obtained by using climbing image nudge elastic band. The energy barrier of CO dissociation on Ir(100) surface is found to be 3.01 eV, which is appreciably larger than the association energy (1.61 eV) of this molecule.

A first principle study for the adsorption and absorption of carbon atom and the CO dissociation on Ir(100) surface

Science.gov (United States)

Erikat, I. A.; Hamad, B. A.

2013-11-01

We employ density functional theory to examine the adsorption and absorption of carbon atom as well as the dissociation of carbon monoxide on Ir(100) surface. We find that carbon atoms bind strongly with Ir(100) surface and prefer the high coordination hollow site for all coverages. In the case of 0.75 ML coverage of carbon, we obtain a bridging metal structure due to the balance between Ir-C and Ir-Ir interactions. In the subsurface region, the carbon atom prefers the octahedral site of Ir(100) surface. We find large diffusion barrier for carbon atom into Ir(100) surface (2.70 eV) due to the strong bonding between carbon atom and Ir(100) surface, whereas we find a very small segregation barrier (0.22 eV) from subsurface to the surface. The minimum energy path and energy barrier for the dissociation of CO on Ir(100) surface are obtained by using climbing image nudge elastic band. The energy barrier of CO dissociation on Ir(100) surface is found to be 3.01 eV, which is appreciably larger than the association energy (1.61 eV) of this molecule.

A first principle study for the adsorption and absorption of carbon atom and the CO dissociation on Ir(100) surface

International Nuclear Information System (INIS)

Erikat, I. A.; Hamad, B. A.

2013-01-01

We employ density functional theory to examine the adsorption and absorption of carbon atom as well as the dissociation of carbon monoxide on Ir(100) surface. We find that carbon atoms bind strongly with Ir(100) surface and prefer the high coordination hollow site for all coverages. In the case of 0.75 ML coverage of carbon, we obtain a bridging metal structure due to the balance between Ir–C and Ir–Ir interactions. In the subsurface region, the carbon atom prefers the octahedral site of Ir(100) surface. We find large diffusion barrier for carbon atom into Ir(100) surface (2.70 eV) due to the strong bonding between carbon atom and Ir(100) surface, whereas we find a very small segregation barrier (0.22 eV) from subsurface to the surface. The minimum energy path and energy barrier for the dissociation of CO on Ir(100) surface are obtained by using climbing image nudge elastic band. The energy barrier of CO dissociation on Ir(100) surface is found to be 3.01 eV, which is appreciably larger than the association energy (1.61 eV) of this molecule

The design of the beamline for magnetic circular dichroism study at HNSRL

CERN Document Server

ShengWeiFan; Li Da Shi; Yan Yong Lia

2000-01-01

A synchrotron radiation beamline for MCD study is being developed at Hefei National Synchrotron Radiation Laboratory (HNSRL) in the P. R. China. As a key component on the beamline, the varied line-spacing plane grating (VLSPG) monochromator is designed to cover a broad photon energy range from 100 to 1000 eV with a medium energy resolving power of 2000. The design is analyzed and optimized to meet the high requirements of MCD studying.

Modified quadrupole mass analyzer RGA-100 for beam plasma research in forevacuum pressure range

Energy Technology Data Exchange (ETDEWEB)

Zolotukhin, D. B.; Tyunkov, A. V. [Tomsk State University of Control Systems and Radioelectronics, 40 Lenin Ave., Tomsk 634050 (Russian Federation); Yushkov, Yu. G., E-mail: yuyushkov@gmail.com [Tomsk State University of Control Systems and Radioelectronics, 40 Lenin Ave., Tomsk 634050 (Russian Federation); Tomsk Polytechnic University, 30 Lenin Ave., Tomsk 634050 (Russian Federation); Oks, E. M. [Tomsk State University of Control Systems and Radioelectronics, 40 Lenin Ave., Tomsk 634050 (Russian Federation); Institute of High Current Electronics SB RAS, 2/3, Akademichesky Ave., Tomsk 634055 (Russian Federation)

2015-12-15

The industrial quadrupole RGA-100 residual gas analyzer was modified for the research of electron beam-generated plasma at forevacuum pressure range. The standard ionizer of the RGA-100 was replaced by three electrode extracting unit. We made the optimization of operation parameters in order to provide the maximum values of measured currents of any ion species. The modified analyzer was successfully tested with beam plasma of argon, nitrogen, oxygen, and hydrocarbons.

Sensorless Control of IM for Limp-Home Mode EV Applications

DEFF Research Database (Denmark)

Dehghan-Azad, Ehsan; Gadoue, Shady; Atkinson, David

2017-01-01

in electric vehicle (EV) applications. The proposed scheme was experimentally tested on a laboratory dynamometer using a 19-kW IM and a 29-kW controller, which are both currently used in the automotive industry for EV applications. The scheme was also implemented on an electric golf buggy which was equipped......This paper presents a novel speed estimation scheme for induction motors (IMs) based on back electromotive-force model reference adaptive system (back-EMF MRAS). The scheme is employed for the purpose of sensorless fault-Tolerant torque-controlled drives used in a limp-home mode operation...... investigated for vehicle starting from standstill, wide speed range including field weakening region, and hill-starting operations. The proposed scheme is computationally easy to implement, robust against sensitivity to parameters variations, inverter nonlinearity and errors due to digitization in the field...

Photoabsorption coefficient of alloys at Al with transition metals V, Fe, Ni and with Cu and Pr from 30 eV to 150 eV photon energy

International Nuclear Information System (INIS)

Hagemann, H.J.; Gudat, W.; Kunz, C.

1975-10-01

The absorption coeffecient of VAl 3 , FeAl, NiAl, NiAl 3 , CuAl 2 , PrAl 2 and of disordered V-Al (16 at. % Al, 28 %, 41%) and Fe-Al (11%) alloys has been measured in the region of the Msub(2,3)-absorption of the transition metals and the L-absorption of Al. The strong changes of the Al spectrum in the region of the 100 eV maximum upon alloying are explained as another evidence of the EXAFS (extended X-ray absorption fine structure) nature of these structures. The broad, prominent absorption peaks from the 3p excitations in V and Fe and from the 4d excitations in Pr are influenced only little on alloying and thus appear to be of atomic origin. The fine structure at the onset of the Pr 4d-transitions is identical in the metal and the alloy but differs from that of Pr oxide. The only Msub(2,3)-edge which is detectably shifted is that if Ni (up to 2.1 eV), whereas the onset of the Al Lsub(2,3)-edge is shifted in all the alloys (up to 1.1 eV). The shifts are interpreted in accordance with X-ray fluorescence and nuclear resonance measurements as changes of the density of states in the valence band of the alloys. (orig.) [de

Optical and Magneto-Optical Properties of Gd22Fe78 Thin Films in the Photon Energy Range From 1.5 to 5.5 eV

Directory of Open Access Journals (Sweden)

Eva Jesenská

2016-01-01

Full Text Available Optical and magneto-optical properties of amorphous Gd22Fe78 (GdFe thin films prepared by direct current (DC sputtering on thermally oxidized substrates were characterized by the combination of spectroscopic ellipsometry and magneto-optical spectroscopy in the photon energy range from 1.5 to 5.5 eV. Thin SiNx and Ru coatings were used to prevent the GdFe surface oxidation and contamination. Using advanced theoretical models spectral dependence of the complete permittivity tensor and spectral dependence of the absorption coefficient were deduced from experimental data. No significant changes in the optical properties upon different coatings were observed, indicating reliability of used analysis.

Crossed beam study of He+-O2 charge transfer reactions in the collision energy range 0.5-200 eV

International Nuclear Information System (INIS)

Bischof, G.; Linder, F.

1986-01-01

Energy spectra and angular distributions of the O + and O 2 + product ions resulting from the He + -O 2 charge transfer reaction have been measured in the collision energy range 0.5-200 eV using the crossed-beam method. The O 2 + ions represent only a minor fraction of the reaction products (0.2-0.6% over the energy range measured). In the dissociative charge transfer reaction, four main processes are identified leading to O+O + reaction products in different electronic states. Two different mechanisms can be distinguished, each being responsible for two of the observed processes: (i) a long-distance energy-resonant charge transfer process involving the c 4 Σsub(u) - (upsilon'=0) state of O 2 + and (ii) a slightly exothermic charge transfer process via the (III) 2 PIsub(u) state of O 2 + (with the exothermicity depending on the collision energy). Angle-integrated branching ratios and partial cross sections (in absolute units) have been determined. The branching ratios of the individual processes show a pronounced dependence on the collision energy. At low energies, the O + product ions are preferentially formed in the 2 P 0 and 2 D 0 excited states. The angular distributions of the O + product ions show an anisotropic behaviour indicating an orientation-dependent charge transfer probability in the He + -O 2 reaction. (orig.)

Investigation of the 93Nb neutron cross-sections in resonance energy range

International Nuclear Information System (INIS)

Grigoriev, Yu.V.; Kitaev, V.Ya.; Zhuravlev, B.V.; Sinitsa, V.V.; Borzakov, S.B.; Faikov-Stanchik, H.; Ilchev, G.; Mezentseva, Zh.V.; Panteleev, Ts.Ts.; Kim, G.N.

2002-01-01

The results of gamma-ray multiplicity spectra and transmission measurements for 93 Nb in energy range 21.5 eV-100 keV are presented. Gamma spectra from 1 to 7 multiplicity were measured on the 501 m and 121 m flight paths of the IBR-30 using a 16-section scintillation detector with a NaI(Tl) crystals of a total volume of 36 l and a 16-section liquid scintillation detector of a total volume of 80 l for metallic samples of 50, 80 mm in diameter and 1, 1.5 mm thickness with 100% 93 Nb. Besides, the total and scattering cross-section of 93 Nb were measured by means batteries of B-10 and He-3 counters on the 124 m, 504 m and 1006 m flight paths of the IBR-30. Spectra of multiplicity distribution were obtained for resolved resonances in the energy region E=30-6000 eV and for energy groups in the energy region E=21.5 eV- 100 keV. They were used for determination of the average multiplicity, resonance parameters and capture cross-section in energy groups and for low-laying resonances of 93 Nb. Standard capture cross-sections of 238 U and experimental gamma-ray multiplicity spectra were also used for determination of capture cross section 93 Nb in energy groups. Similar values were calculated using the ENDF/B-6 and JENDL-3 evaluated data libraries with the help of the GRUKON computer program. Within the limits of experimental errors there is observed an agreement between the experiment and calculation, but in some groups the experimental values differ from the calculated ones. (author)

EV Charging Algorithm Implementation with User Price Preference

Energy Technology Data Exchange (ETDEWEB)

Wang, Bin; Hu, Boyang; Qiu, Charlie; Chu, Peter; Gadh, Rajit

2015-02-17

in this paper, we propose and implement a smart Electric Vehicle (EV) charging algorithm to control the EV charging infrastructures according to users’ price preferences. EVSE (Electric Vehicle Supply Equipment), equipped with bidirectional communication devices and smart meters, can be remotely monitored by the proposed charging algorithm applied to EV control center and mobile app. On the server side, ARIMA model is utilized to fit historical charging load data and perform day-ahead prediction. A pricing strategy with energy bidding policy is proposed and implemented to generate a charging price list to be broadcasted to EV users through mobile app. On the user side, EV drivers can submit their price preferences and daily travel schedules to negotiate with Control Center to consume the expected energy and minimize charging cost simultaneously. The proposed algorithm is tested and validated through the experimental implementations in UCLA parking lots.

KAKOVOST OTROŠKIH AVTOSEDEŽEV

OpenAIRE

Pavlin, Valentina

2011-01-01

Namen diplomskega dela je podati predloge za izboljšanje nivoja poznavanja kakovosti v povezavi z uporabnostjo otroških avtosedežev. S pomočjo anketnega vprašalnika smo pridobili pomembna mnenja uporabnikov o otroških avtosedežih. Raziskava je vključevala 50 anketirancev, ki so bili naključno izbrani v eni izmed otroških trgovin. Rezultati ankete so pokazali, da uporabniki osnovno znanje o kakovosti otroških avtosedežev imajo. Na prvo mesto uvrščajo kakovost in varnost, najmanj pa se...

A multi-factor GIS method to identify optimal geographic locations for electric vehicle (EV) charging stations

Science.gov (United States)

Zhang, Yongqin; Iman, Kory

2018-05-01

Fuel-based transportation is one of the major contributors to poor air quality in the United States. Electric Vehicle (EV) is potentially the cleanest transportation technology to our environment. This research developed a spatial suitability model to identify optimal geographic locations for installing EV charging stations for travelling public. The model takes into account a variety of positive and negative factors to identify prime locations for installing EV charging stations in Wasatch Front, Utah, where automobile emission causes severe air pollution due to atmospheric inversion condition near the valley floor. A walkable factor grid was created to store index scores from input factor layers to determine prime locations. 27 input factors including land use, demographics, employment centers etc. were analyzed. Each factor layer was analyzed to produce a summary statistic table to determine the site suitability. Potential locations that exhibit high EV charging usage were identified and scored. A hot spot map was created to demonstrate high, moderate, and low suitability areas for installing EV charging stations. A spatially well distributed EV charging system was then developed, aiming to reduce "range anxiety" from traveling public. This spatial methodology addresses the complex problem of locating and establishing a robust EV charging station infrastructure for decision makers to build a clean transportation infrastructure, and eventually improve environment pollution.

Cosmic rays: the spectrum and chemical composition from 10{sup 10} to 10{sup 20} eV

Energy Technology Data Exchange (ETDEWEB)

Peixoto, C.J. Todero; De Souza, Vitor [Instituto de Física de São Carlos, Universidade de São Paulo, Av. Trabalhador São-carlense 400, São Carlos (Brazil); Biermann, Peter L., E-mail: toderocj@usp.br, E-mail: vitor@ifsc.usp.br, E-mail: plbiermann@mpifr-bonn.mpg.de [Max-Planck-Institute for Radioastronomy, Auf dem Hügel 69, 53121 Bonn (Germany)

2015-07-01

The production of energetic particles in the universe remains one of the great mysteries of modern science. The mechanisms of acceleration in astrophysical sources and the details about the propagation through the galactic and extragalactic media are still to be defined. In recent years, the cosmic ray flux has been measured with high precision in the energy range from 10{sup 10} to 10{sup 20.5} eV by several experiments using different techniques. In some energy ranges, it has been possible to determine the flux of individual elements (hydrogen to iron nuclei). This paper explores an astrophysical scenario in which only our Galaxy and the radio galaxy Cen A produce all particles measured on Earth in the energy range from 10{sup 10} to 10{sup 20.5} eV . Data from AMS-02, CREAM, KASCADE, KASCADE-Grande and the Pierre Auger Observatories are considered. The model developed here is compared to the total and if available to the individual particle flux of the experiments considered.The flux of each element as determined by AMS-02, CREAM, KASCADE and KASCADE-Grande and the mass sensitivity parameter X{sub max} measured by the Pierre Auger Observatory above 10 eV are also explored within the framework of the model. The transition from 10{sup 16} to 10{sup 18} eV is carefully analyzed. It is shown that the flux measured in this energy range suggest the existence of an extra component of cosmic rays yet to be understood.

17 CFR 229.1000 - (Item 1000) Definitions.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false (Item 1000) Definitions. 229.1000 Section 229.1000 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION STANDARD INSTRUCTIONS FOR FILING FORMS UNDER SECURITIES ACT OF 1933, SECURITIES EXCHANGE ACT OF 1934 AND ENERGY POLICY AND CONSERVATION ACT OF 1975-REGULATION...

EV-GHG Mobile Source

Data.gov (United States)

U.S. Environmental Protection Agency — The EV-GHG Mobile Source Data asset contains measured mobile source GHG emissions summary compliance information on light-duty vehicles, by model, for certification...

Evaluation of the 237Np neutron cross sections in the energy range from 10-5 eV to 5 MeV

International Nuclear Information System (INIS)

Derrien, H.; Fort, E.

1979-01-01

The 237 Np neutron cross-sections have been evaluated in the energy range from thermal to 5 MeV. A set of resonance parameters including a negative level, is recommanded after examination of the available experimental data. This set is used 1) to calculate the cross-sections from the thermal region to 150 ev, and 2) to provide the statistical parameters suitable to the calculations in the unresolved region. At higher energies, the transmission coefficients Te are calculated by the coupled channel optical model code ECIS. They are then used as input in the statistical model code FISINGA. The optical model parameters, including the deformation parameters, are those used by Lagrange for the Pu isotopes, slightly modified to reproduce at 40 KeV the total cross-sections obtained from the pure statistical parameters. The recommendations of Lynn concerning the level density parameters have been used. In this paper we describe the various steps of the evaluation

Low-Cost GRIN-Lens-Based Nephelometric Turbidity Sensing in the Range of 0.1-1000 NTU.

Science.gov (United States)

Metzger, Michael; Konrad, Alexander; Blendinger, Felix; Modler, Andreas; Meixner, Alfred J; Bucher, Volker; Brecht, Marc

2018-04-06

Turbidity sensing is very common in the control of drinking water. Furthermore, turbidity measurements are applied in the chemical (e.g., process monitoring), pharmaceutical (e.g., drug discovery), and food industries (e.g., the filtration of wine and beer). The most common measurement technique is nephelometric turbidimetry. A nephelometer is a device for measuring the amount of scattered light of suspended particles in a liquid by using a light source and a light detector orientated in 90° to each other. Commercially available nephelometers cost usually-depending on the measurable range, reliability, and precision-thousands of euros. In contrast, our new developed GRIN-lens-based nephelometer, called GRINephy, combines low costs with excellent reproducibility and precision, even at very low turbidity levels, which is achieved by its ability to rotate the sample. Thereby, many cuvette positions can be measured, which results in a more precise average value for the turbidity calculated by an algorithm, which also eliminates errors caused by scratches and contaminations on the cuvettes. With our compact and cheap Arduino-based sensor, we are able to measure in the range of 0.1-1000 NTU and confirm the ISO 7027-1:2016 for low turbidity values.

Dissolution of B-doped S1(100) layers in NaOH aqueous solutions

International Nuclear Information System (INIS)

Akhter, P.; Baig, A.; Mufti, A.

1988-12-01

NaOH solution has been used to study the dissolution rates of boron doped Sl(100) wafers as a function of solution normality (0.02 N to 15 N) and temperature in the range of 30 deg. C to boiling point. For a dissolution at boiling point, two distinctive ranges of solution normalities have been observed. For N ≤ 4.5, the dissolution rate increases logarithmically and is defect dependent. For higher values of N ≥ 4.5 normal, the dissolution rate becomes a linear function of normality and reaction is defect dependent. The reaction activation energy has been measured equal to 0.65 +- 0.03 eV. (author). 7 refs, 5 figs

Differential and integral electron scattering cross sections from tetrahydrofuran (THF) over a wide energy range: 1-10.000 eV

International Nuclear Information System (INIS)

Fuss, M.C.; Sanz, A.G.; Blanco, F.; Limao-Vieira, P.; Brunger, M.J.; Garcia, G.

2014-01-01

Tetrahydrofuran (THF, C 4 H 8 O) has a molecular structure that is similar to the ribose in the DNA backbone and is used as a surrogate of ribose to get electron scattering cross sections. Total, integral inelastic and integral and differential elastic cross sections have been calculated with the screening-corrected additivity rule (SCAR) method based on the independent atom model (IAM) for electron scattering from THF. Since the permanent dipole moment of THF enhances rotational excitation particularly at low energies and for small angles, an estimate of the rotational excitation cross section was also computed by assuming the interaction with a free electric dipole as an independent, additional process. Our theoretical results compare very favourably to the existing experimental data. Finally, a self-consistent set of integral and differential interaction cross-sections for the incident energy range 1 eV - 10 keV is established for use in our low energy particle track simulation (LEPTS). All cross section data are supplied numerically in tabulated form. (authors)

Low-energy positron and electron diffraction and positron-stimulated secondary electron emission from Cu(100)

International Nuclear Information System (INIS)

Weiss, A.H.

1983-01-01

The results of two series of experiments are reported. In the first, an electrostatically guided beam of low-energy (40-400 eV) positrons, delta/sub p/ was used to study low-energy positron diffraction (LEPD) from a Cu(100) surface under ultrahigh-vacuum conditions. Low-energy electron diffraction (LEED) data were obtained from the same sample in the same apparatus. Comparison of LEPD and LEED intensity versus energy data with model calculations made using computer programs developed by C.B. Duke and collaborators indicated that: LEPD data is adequately modeled using potentials with no exchange-correlation term. The inelastic mean free path, lambda/sub ee/, is shorter for positrons than for electrons at low (< approx.80 eV). LEED is better than LEPD at making a determination of the first-layer spacing of Cu(100) for the particular data set reported. In the second set of experiments, the same apparatus and sample were used to compare positron- and electron-stimulated secondary-electron emission (PSSEE and ESSEE). The results were found to be consistent with existing models of secondary-electron production for metals. The energy distributions of secondary-electrons had broad low-energy (<10 eV) peaks for both positron and electron stimulation. But the PSEE distribution showed no elastic peak. Measurements of secondary-electron angular distributions, found to be cosine-like in both the PSSEE and ESSEE case, were used to obtain total secondary yield ratios, delta, at four beam energies ranging from 40-400 eV. The secondary yield ratio for primary positrons and the yield for primary electrons, delta/sub e/, were similar at these energies. For 400-eV primary particles the secondary yields were found to be delta/sub p/ = 0.94 +/- 0.12 and delta/sub e/ = 0.94 +/- 0./12, giving a ratio of unity for positron-stimulated secondary yield to electron-stimulated secondary yield

Bombardment of Ni(100) surface with low-energy argons: molecular dynamics simulations

International Nuclear Information System (INIS)

Guevenc, Ziya B.; Hippler, Rainer; Jackson, Bret

2005-01-01

Results of molecular dynamics simulations of the sputtering of Ni(100) by Ar atoms are reported. The solid is described by an embedded atom potential, and the interaction between the projectile and the metal atoms is modelled by a Morse-like function. Processes leading to Ni atom emissions from the lattice are analysed over the energy range of 70-80 eV. In this energy range cluster (larger than three atoms) emission is not observed. The maximum penetration depth of Ar, the kinetic energy and angular distributions of the reflected Ar, and the sputtered Ni atoms are evaluated as functions of the impact energy and sputtering time. The computed sputtering yield is compared with the available theoretical and experimental data

Neutron Transmission and Capture Measurements and Resonance Parameter Analysis of Neodymium from 1eV to 500 eV

International Nuclear Information System (INIS)

DP Barry; MJ Trbovich; Y Danon; RC Block; RE Slovacek

2005-01-01

Neodymium is a 235 U fission product and is important for reactor neutronic calculations. The aim of the present work is to improve upon the existing neutron cross section data of neodymium. Neutron capture and transmission measurements were performed by the time-off-light technique at the Rensselaer Polytechnic Institute LINAC laboratory using metallic neodymium samples. The capture measurements were made at the 25-m flight station with a 16-segment NaI multiplicity detector, and the transmission measurements were performed at 15-m and 25-m flight stations, respectively, with 6 Li glass scintillation detectors. After the data were collected and reduced, resonance parameters were determined by combined fitting of the transmission and capture data with the multilevel R-matrix Bayesian code SAMMY. The resonance parameters for all naturally occurring neodymium isotopes were deduced within the energy range of 1 eV to 500 eV. The resulting resonance parameters were used to calculate the capture resonance integrals from this energy. The RPI parameters gave a resonance integral value of 32 ± 1 barns that is approximately 7% lower than that obtained with the ENDF-B/VI parameters. The current measurements significantly reduce the uncertainties on the resonance parameters when compared with previously published parameters

Deuteron stripping on beryllium target in the 100-2300 MeV energy range

International Nuclear Information System (INIS)

Lecolley, J.F.; Varignon, C.; Durand, D.; Le Brun, C.; Lecolley, F.R.; Lefebvres, F.; Louvel, M.; Thun, J.; Borne, F.; Martinez, E.; Menard, S.; Pras, P.; Boudard, A.; Duchazeaubeneix, J.C.; Durand, J.M.; Frehaut, J.; Hanappe, F.; Ledoux, X.; Legrain, R.; Leray, S.; Milleret, G.; Patin, Y.; Stuttge, L.; Terrien, Y.

1999-01-01

Cross sections for stripping and dissociation of deuterons interacting with Be targets in the 100-2300 MeV energy range have been measured. Comparisons with model calculations suggest a dominant contribution of the stripping process. It is also shown that the deuteron break-up cross section exhibits the same energy dependence as the nucleon-nucleon cross section. (orig.)

Extending the Compositional Range of Nanocasting in the Oxozirconium Cluster-Based Metal–Organic Framework NU-1000—A Comparative Structural Analysis

Energy Technology Data Exchange (ETDEWEB)

Zhao, Wenyang [Department; Wang, Zhao [Department; Malonzo, Camille D. [Department; Webber, Thomas E. [Department; Platero-Prats, Ana E. [X-ray; Sotomayor, Francisco [Quantachrome Instruments, 1900 Corporate; Vermeulen, Nicolaas A. [Department; Wang, Timothy C. [Department; Hupp, Joseph T. [Department; Farha, Omar K. [Department; Department; Penn, R. Lee [Department; Chapman, Karena W. [X-ray; Thommes, Matthias [Quantachrome Instruments, 1900 Corporate; Stein, Andreas [Department

2018-02-08

The process of nanocasting in metal-organic frameworks (MOFs) is a versatile approach to modify these porous materials by introducing supporting scaffolds. The nanocast scaffolds can stabilize metal-oxo clusters in MOFs at high temperatures and modulate their chemical environments. Here we demonstrate a range of nanocasting approaches in the MOF NU-1000, which contains hexanuclear oxozirconium clusters (denoted as Zr6 clusters) that are suitable for modification with other metals. We developed methods for introducing SiO2, TiO2, polymeric, and carbon scaffolds into the NU-1000 structure. The responses of NU-1000 towards different scaffold precursors were studied, including the effects on morphology, precursor distribution, and porosity after nanocasting. Upon removal of organic linkers in the MOF by calcination/pyrolysis at 500 °C or above, the Zr6 clusters remained accessible and maintained their Lewis acidity in SiO2 nanocast samples, whereas additional treatment was necessary for Zr6 clusters to become accessible in carbon nanocast samples. Aggregation of Zr6 clusters was largely prevented with SiO2 or carbon scaffolds even after thermal treatment at 500 °C or above. In the case of titania nanocasting, NU- 1000 crystals underwent a pseudomorphic transformation, in which Zr6 clusters reacted with titania to form small oxaggregates of a Zr/Ti mixed oxide with a local structure resembling that of ZrTi2O6. The ability to maintain high densities of discrete Lewis acidic Zr6 clusters on SiO2 or carbon supports at high temperatures provides a starting point for designing new thermally stable catalysts.

Instant LEGO Mindstorm EV3

CERN Document Server

Garber, Gary

2013-01-01

Filled with practical, step-by-step instructions and clear explanations for the most important and useful tasks. A concise guide full of step-by-step recipes to teach you how to build and program an advanced robot.""Instant LEGO Mindstorm EV3"" is for both the adult tinkerer who has never touched LEGO before and the experienced LEGO engineer who has evolved from Mindstorm NXT to EV3. If you are interested in entering or advising students in robot competitions such as the FIRST LEGO League, the Wold Robot Olympiad, or RoboGames, then this book is a must for you. Even if you haven't purchased yo

Hysteresis of thin film IPRTs in the range 100 °C to 600 °C

Science.gov (United States)

Zvizdić, D.; Šestan, D.

2013-09-01

As opposed to SPRTs, the IPRTs succumb to hysteresis when submitted to change of temperature. This uncertainty component, although acknowledged as omnipresent at many other types of sensors (pressure, electrical, magnetic, humidity, etc.) has often been disregarded in their calibration certificates' uncertainty budgets in the past, its determination being costly, time-consuming and not appreciated by customers and manufacturers. In general, hysteresis is a phenomenon that results in a difference in an item's behavior when approached from a different path. Thermal hysteresis results in a difference in resistance at a given temperature based on the thermal history to which the PRTs were exposed. The most prominent factor that contributes to the hysteresis error in an IPRT is a strain within the sensing element caused by the thermal expansion and contraction. The strains that cause hysteresis error are closely related to the strains that cause repeatability error. Therefore, it is typical that PRTs that exhibit small hysteresis also exhibit small repeatability error, and PRTs that exhibit large hysteresis have poor repeatability. Aim of this paper is to provide hysteresis characterization of a batch of IPRTs using the same type of thin-film sensor, encapsulated by same procedure and same company and to estimate to what extent the thermal hysteresis obtained by testing one single thermometer (or few thermometers) can serve as representative of other thermometers of the same type and manufacturer. This investigation should also indicate the range of hysteresis departure between IPRTs of the same type. Hysteresis was determined by cycling IPRTs temperature from 100 °C through intermediate points up to 600 °C and subsequently back to 100 °C. Within that range several typical sub-ranges are investigated: 100 °C to 400 °C, 100 °C to 500 °C, 100 °C to 600 °C, 300 °C to 500 °C and 300 °C to 600 °C . The hysteresis was determined at various temperatures by

Time delays of supernova neutrinos from new long-range interactions

International Nuclear Information System (INIS)

Malaney, R.A.; Starkman, G.D.; Tremaine, S.

1995-01-01

A new long-range interaction between heavy neutrinos may solve some current problems in large-scale structure, if the new interaction mimics gravity. Assuming that the dark matter is dominated by ∼100 eV τ neutrinos, we investigate whether time delay measurements on supernova neutrinos can test this possibility. We find that such experiments can rule out or detect specific forms of the new interaction potential. In addition, we find the exact dispersive nature of the interacting medium to be critical in determining the time delay: even small corrections to the potential can dramatically alter the magnitude of the effect

Oxidation-induced deformation of zircaloy-4 tubing in steam in the temperature range 600-1000 degree C

International Nuclear Information System (INIS)

Aly, A.E.; Hussein, A.G.; EL-Raghy, S.M.; EL-Sayed, A.A.; EL-Banna, O.A.

1992-01-01

The oxidation-induced deformation of zircaloy-4 (zry-4) tubing in steam has been studied in the temperature range 600 to 1000 degree C. The induced deformation has been measured in both radial and axial directions of the tube. The effect of hydrogen addition to steam was also investigated. The oxidation-induced deformation has been characterized by uniform and non-uniform (distortion) strain period. During the uniform strain period the radial strain kinetics were found in general, to be parallel to the oxidation kinetics. The axial strain (δA) induced by oxidation was found to be always lower than the radial strain (εR). The addition of 5% by volume hydrogen to steam leads to an increase in the oxidation rate and to a decrease in the degree of anisotropy between radial and axial strains

Characterization and hydrogen gas sensing properties of TiO{sub 2} thin films prepared by sol-gel method

Energy Technology Data Exchange (ETDEWEB)

Haidry, Azhar Ali [Department of Experimental Physics, Faculty of Mathematics, Physics and Informatics, Comenius University, Bratislava (Slovakia); Puskelova, Jarmila [Department of Inorganic Chemistry, Faculty of Natural Sciences, Comenius University, Bratislava (Slovakia); Plecenik, Tomas; Durina, Pavol; Gregus, Jan; Truchly, Martin; Roch, Tomas; Zahoran, Miroslav [Department of Experimental Physics, Faculty of Mathematics, Physics and Informatics, Comenius University, Bratislava (Slovakia); Vargova, Melinda [Department of Inorganic Chemistry, Faculty of Natural Sciences, Comenius University, Bratislava (Slovakia); Kus, Peter; Plecenik, Andrej [Department of Experimental Physics, Faculty of Mathematics, Physics and Informatics, Comenius University, Bratislava (Slovakia); Plesch, Gustav, E-mail: plesch@fns.uniba.sk [Department of Inorganic Chemistry, Faculty of Natural Sciences, Comenius University, Bratislava (Slovakia)

2012-10-15

Highlights: Black-Right-Pointing-Pointer Preparation and characterization of hydrogen sensing TiO{sub 2} thin films by sol-gel method. Black-Right-Pointing-Pointer The annealing effect on the structure, electrical, optical and sensing properties was studied. Black-Right-Pointing-Pointer The best sensitivity show the films composed of rutile with grain size of {approx}100 nm. - Abstract: Thin films of titanium dioxide with thickness of about 150 nm were deposited by spin coating method on a sapphire substrate from a sol-gel and annealed at various temperatures (from 600 Degree-Sign C to 1000 Degree-Sign C). Structural, optical and hydrogen gas sensing properties of the films were investigated. The annealing temperatures from 600 to 800 Degree-Sign C led to anatase phase with grain size in the range of 14-28 nm. Further increase of the annealing temperature resulted in transformation to rutile phase with larger grain size of about 100-120 nm. The optical band gap tended to decrease with increasing annealing temperature. The estimated values of activation energy for charge transport were in the range of 0.6-1.0 eV for films annealed at temperatures from 600 Degree-Sign C to 800 Degree-Sign C and 0.37-0.38 eV for films annealed at 900 Degree-Sign C and 1000 Degree-Sign C. The films annealed at 900 Degree-Sign C and 1000 Degree-Sign C showed better hydrogen sensitivity, what can be at least partially caused by their higher surface roughness.

Extreme Ultraviolet Emission Spectrum of CO_2 Induced by Electron Impact at 200 eV

Science.gov (United States)

Kanik, I.; Ajello, J. M.; James, G. K.

1993-01-01

We present the extreme ultraviolet (EUV) emission spectrum of CO_2 induced by electronimpact at 200 eV. There are 36 spectral features which are identified with a resolution of 0.5 nmover the wavelength range of 40 to 125 nm. Absolute emission cross sections were obtained for eachof these features. The EUV emission spectrum induced by electron impact consist of atomicmultiplets of CI,II and OI,II,III as well as CO and CO^+ molecular band systems produced bydissociative excitation. The CI (119.4 nm) multiplet is the strongest feature of CI with a peak crosssection of 3.61 x 10^(-19) cm^2 at 200 eV. The strongest feature of OI in the EUV spectrum is theOI (99.0 nm) multiplet with a peak cross section of 3.59 x 10^(-19) cm^2 at 200 eV.

Cosmic rays around 1018 eV: Implications of contemporary measurements on the origin of the ankle feature

International Nuclear Information System (INIS)

Deligny, O.

2014-01-01

The impressive power-law decay of the energy spectrum of cosmic rays over more than thirty orders of magnitude in intensity and for energies ranging over eleven decades between 10 9 eV and 10 20 eV is actually dotted with small irregularities. These irregularities are highly valuable for uncovering and understanding the modes of production and propagation of cosmic rays. They manifest themselves through changes in the spectral index characterising the observed power laws. One of these irregularities, known as the ankle, is a hardening of the energy spectrum of cosmic rays in the 10 18 eV energy range. There are many possible interpretations for explaining it. One is to say that the ankle may be the spectral feature marking the transition between Galactic and extragalactic cosmic rays. Another one is to understand the ankle as the natural distortion of a proton-dominated extragalactic spectrum due to e ± pair production in the collisions with the photons of the cosmic microwave background. While the data collected at the Telescope Array supports the second explanation, the data collected at the Pierre Auger Observatory requires a totally different picture in terms of introducing a new component mainly composed of light elements in order to fill the gap of the all-particle energy spectrum between 10 17 eV and 4*10 18 eV, and to reproduce the measurements related to mass composition. If contemporary observations characterising the ankle have shed new lights, they are still far from being able to deliver all the story

Dissociative photoionization of IBr following I(4d) and Br(3d) inner-shell excitations in the range of 60 ∼ 133 eV: remarkable biased charge spread relevant to the core-hole states

International Nuclear Information System (INIS)

Boo, Bong Hyun; Koyano, Inosuke

2002-01-01

Dissociative photoionization of an interhalogen molecule, iodine monobromide (IBr), spanning the I(4d) and the Br(3d) inner-shell excitation/ionization regions has been studied by using time-of-flight (TOF) mass spectrometry coupled to synchrotron radiation in the range of 60 ∼ 133 eV. The total and the individual photoion yields have been recorded as functions of the photon energy. Here, a giant shape resonance has been observed owing to the I(4d 10 ) →I(4d 9 εf) transition, the transition probability for which outweighs that for the Br(3d 10 ) →Br(3d 9 εf) excitation. In addition to the huge resonance, discrete resonances owing to the Br(3d) -1 IBr(4pσ + ) and the Br(3d -1 )Br(5p) transitions, with very weak intensities, are observed at 70.5 and 73.6 eV and have spin-orbit splittings of = 1.0 and = 0.9 eV, respectively. The dissociation processes of singly and doubly charged parent ions have also been evaluated from the variations of the individual ion and photoion-photoion coincidence (PIPICO) yields with the photon energy. Below the Br(3d) threshold, including the Br(3d) discrete excitation region, 60 + and I 2+ ions are exclusively formed with a trace number of Br + ions. Slightly above the Br(3d) threshold, more specifically at 77.5 eV, however, photoionization events leading to the formations of Br + and Br 2- prevail. At higher energies beyond the Br(3d) threshold, 78 + and I 2+ turn out to exceed again those for Br + and Br 2+ , respectively. Over the entire energy range examined, a remarkable biased charge spread in dissociative photoionization events is observed, presumably reflecting the fact that charge localized mostly in the excited atoms relevant to the specific inner-shell excitation, which can be accounted for mainly by a two-step decay process via a fast dissociation followed by autoionization upon vuv absorption

Smart EV Energy Management System to Support Grid Services

Science.gov (United States)

Wang, Bin

Under smart grid scenarios, the advanced sensing and metering technologies have been applied to the legacy power grid to improve the system observability and the real-time situational awareness. Meanwhile, there is increasing amount of distributed energy resources (DERs), such as renewable generations, electric vehicles (EVs) and battery energy storage system (BESS), etc., being integrated into the power system. However, the integration of EVs, which can be modeled as controllable mobile energy devices, brings both challenges and opportunities to the grid planning and energy management, due to the intermittency of renewable generation, uncertainties of EV driver behaviors, etc. This dissertation aims to solve the real-time EV energy management problem in order to improve the overall grid efficiency, reliability and economics, using online and predictive optimization strategies. Most of the previous research on EV energy management strategies and algorithms are based on simplified models with unrealistic assumptions that the EV charging behaviors are perfectly known or following known distributions, such as the arriving time, leaving time and energy consumption values, etc. These approaches fail to obtain the optimal solutions in real-time because of the system uncertainties. Moreover, there is lack of data-driven strategy that performs online and predictive scheduling for EV charging behaviors under microgrid scenarios. Therefore, we develop an online predictive EV scheduling framework, considering uncertainties of renewable generation, building load and EV driver behaviors, etc., based on real-world data. A kernel-based estimator is developed to predict the charging session parameters in real-time with improved estimation accuracy. The efficacy of various optimization strategies that are supported by this framework, including valley-filling, cost reduction, event-based control, etc., has been demonstrated. In addition, the existing simulation-based approaches do

First-principles calculation of adsorption of shale gas on CaCO3 (100) surfaces.

Science.gov (United States)

Luo, Qiang; Pan, Yikun; Guo, Ping; Wang, Zhouhua; Wei, Na; Sun, Pengfei; Liu, Yuxiao

2017-06-16

To demonstrate the adsorption strength of shale gas to calcium carbonate in shale matrix, the adsorption of shale gas on CaCO3 (100) surfaces was studied using the first-principles method, which is based on the density functional theory (DFT). The structures and electronic properties of CH4, C2H6, CO2 and N2 molecules were calculated by the generalized gradient approximation (GGA), for a coverage of 1 monolayer (ML). Under the same conditions, the density of states (DOS) of CaCO3 (100) surfaces before and after the adsorption of shale gas molecules at high-symmetry adsorption sites were compared. The results showed that the adsorption energies of CH4, C2H6, CO2 and N2 on CaCO3 (100) surfaces were between 0.2683 eV and -0.7388 eV. When a CH4 molecule was adsorbed at a hollow site and its 2 hydrogen atoms were parallel to the long diagonal (H3) on the CaCO3 (100) surface, it had the most stable adsorption, and the adsorption energy was only -0.4160 eV. The change of adsorption energy of CH4 was no more than 0.0535 eV. Compared with the DOS distribution of CH4 before adsorption, it shifted to the left overall after adsorption. At the same time, the partial density of states (PDOS) curves of CaCO3 (100) surfaces before and after adsorption basically overlapped. This work showed that the adsorption effect of shale gas on calcium carbonate is very weak, and the adsorption is physisorption at the molecular level.

Phenotypic and genotypic characteristics of novel mouse cell line (NIH/3T3-adapted human enterovirus 71 strains (EV71:TLLm and EV71:TLLmv.

Directory of Open Access Journals (Sweden)

Carla Bianca Luena Victorio

Full Text Available Since its identification in 1969, Enterovirus 71 (EV71 has been causing periodic outbreaks of infection in children worldwide and most prominently in the Asia-Pacific Region. Understanding the pathogenesis of Enterovirus 71 (EV71 is hampered by the virus's inability to infect small animals and replicate in their derived in vitro cultured cells. This manuscript describes the phenotypic and genotypic characteristics of two selected EV71 strains (EV71:TLLm and EV71:TLLmv, which have been adapted to replicate in mouse-derived NIH/3T3 cells, in contrast to the original parental virus which is only able to replicate in primate cell lines. The EV71:TLLm strain exhibited productive infection in all primate and rodent cell lines tested, while EV71:TLLmv exhibited greater preference for mouse cell lines. EV71:TLLmv displayed higher degree of adaptation and temperature adaptability in NIH/3T3 cells than in Vero cells, suggesting much higher fitness in NIH/3T3 cells. In comparison with the parental EV71:BS strain, the adapted strains accumulated multiple adaptive mutations in the genome resulting in amino acid substitutions, most notably in the capsid-encoding region (P1 and viral RNA-dependent RNA polymerase (3D. Two mutations, E167D and L169F, were mapped to the VP1 canyon that binds the SCARB2 receptor on host cells. Another two mutations, S135T and K140I, were located in the VP2 neutralization epitope spanning amino acids 136-150. This is the first report of human EV71 with the ability to productively infect rodent cell lines in vitro.

Reliability of the Nidek NT-1000 non contact tonometer.

Science.gov (United States)

Van de Velde, T; Zeyen, T

1995-01-01

In this prospective study, we compared the intraocular pressure (IOP) readings of 100 patients measured with the Goldmann applanation tonometer and the Nidek NT-1000 pneumotonometer. The correlation coefficient between the Goldmann and Nidek readings was 0.86. On the average the pneumotonometer overestimated the intraocular pressure with 0.43 mm Hg. The Nidek NT-1000 non contact tonometer can be used for screening purposes provided an appropriately low IOP value is used to indicate the need for further assessment with the Goldman applanation tonometer.

ICT Solutions to Support EV Deployment

DEFF Research Database (Denmark)

Pedersen, Anders Bro; Andersen, Peter Bach; Skov Johansen, Joachim

2013-01-01

Numerous studies and projects have proven that the electric vehicle can offer value and services that go beyond its function as a means of transportation. The value and services can, for instance, be the reduction of charging costs, adherence to grid constraints, or adjustment of charging behavior...... utilization concepts for EVs and be harmonized to obtain interoperability among numerous electric vehicle (EV) and electric vehicle supply equipment from original equipment manufacturers. This chapter describes contemporary Smart Grid communication methods in terms of requirements and specific solutions...

Fabrication and evaluation of 100 Ah cylindrical lithium ion battery for electric vehicle applications

Science.gov (United States)

Hyung, Yoo-Eup; Moon, Seong-In; Yum, Duk-Hyeng; Yun, Seong-Kyu

A total of 100 Ah class lithium ion cells with C/LiCoO 2 cell system for electric vehicles (EVs) was developed. EV-size lithium ion battery was developed by Sony, KERI/STC, SAFT, VARTA, Sanyo and Matsushita. GS battery and Hitachi have developed also stationary type large scale (70-80 Ah) lithium ion batteries. Lithium ion battery module for EVs was demonstrated by Sony/Nissan and KERI/STC in 1996. At present, the performance of developed EV-cells was up to 115 Wh/kg and 286 W/kg of specific power at 80% DOD. We assume our EV cells to have 248 and 242 km driving distance per one charge with DST-120 mode and ECE-15 mode, respectively. Finally, we performed safety/abuse tests of developed lithium ion cell.

100 MeV silver ions induced defects and modifications in silica glass

Energy Technology Data Exchange (ETDEWEB)

Jadhav, Vijay S.; Deore, Avinash V.; Dahiwale, S.S. [Department of Physics, University of Pune, Pune 411007 (India); Kanjilal, D. [Inter University Accelerator Centre, New Delhi 110067 (India); Bhoraskar, V.N. [Department of Physics, University of Pune, Pune 411007 (India); Dhole, S.D., E-mail: sanjay@physics.unipune.ac.in [Department of Physics, University of Pune, Pune 411007 (India)

2014-07-15

Highlights: •Study of silver ion induced defects and modifications in silica glass. •Variation in oxygen deficiency centres (ODA-II) and nonbridging oxygen hole centres (NBOHC). •Study of structural damage in terms of Urbach energy. -- Abstract: A few silica glass samples having 1 cm{sup 2} area and 0.1 cm thickness were irradiated with 100 MeV energy Ag{sup 7+} ions for the fluences ranging from 1 × 10{sup 12} ions/cm{sup 2} to 5 × 10{sup 13} ions/cm{sup 2}. The optical properties and the corresponding induced defects were characterised by the techniques such as UV–Visible, Photoluminescence (PL), Fourier transform infrared (FTIR), and Electron spin resonance (ESR) spectroscopy. The UV–Visible absorption spectra show two peaks, one at 5 eV and another weak peak at 5.8 eV. A peak observed at 5.0 eV corresponds to B{sub 2} band (oxygen deficiency in SiO{sub 2} network) and the peak at 5.8 eV is due to the paramagnetic defects like E′ centre. The intensities of these peaks found to be increased with increase in ion fluence. It attributes to the increase in the concentration of E′ centres and B{sub 2} band respectively. In addition, the optical band gap energy, Urbach energy and the defects concentration have been calculated using Urbach plot. The optical band gap found to be decreased from 4.65 eV to 4.39 eV and the Urbach energy found to be increased from 60 meV to 162 meV. The defect concentration of nonbridging oxygen hole centres (NBOHC) and E′ centres are found to be increased to 1.69 × 10{sup 13} cm{sup −3} and 3.134 × 10{sup 14} cm{sup −3} respectively. In PL spectra, the peak appeared at 1.92 eV and 2.7 eV envisage the defects of nonbridging oxygen hole centres and B{sub 2α} oxygen deficient centres respectively. ESR spectra also confirms the existence of E′ and NBOHC centres. FTIR spectra shows scissioning of Si-O-Si bonds and the formation of Si-H and Si-OH bonds, which supports to the co-existence of the defects induced by Ag

EV City Casebook: A Look At The Global Electric Vehicle Movement

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

Electric vehicles (EVs) hold the potential of transforming the way the world moves. EVs can increase energy security by diversifying the fuel mix and decreasing dependence on petroleum, while also reducing emissions of greenhouse gases and other pollutants. Just as important, EVs can unlock innovation and create new advanced industries that spur job growth and enhance economic prosperity. However, the mass deployment of EVs will require transportation systems capable of integrating and fostering this new technology. To accelerate this transition, cities and metropolitan regions around the world are creating EV-friendly ecosystems and building the foundation for widespread adoption. In recognition of the importance of urban areas in the introduction and scale-up of electric vehicles, the EV City Casebook presents informative case studies on city and regional EV deployment efforts around the world. These case studies are illustrative examples of how pioneering cities are preparing the ground for mass market EV deployment. They offer both qualitative and quantitative information on cities' EV goals, progress, policies, incentives, and lessons learned to date. The purpose of the EV City Casebook is to share experiences on EV demonstration and deployment, identify challenges and opportunities, and highlight best practices for creating thriving EV ecosystems. These studies seek to enhance understanding of the most effective policy measures to foster the uptake of electric vehicles in urban areas. The cities represented here are actively engaging in a variety of initiatives that share the goal of accelerating EV adoption. This publication is the result of an effort to coordinate those initiatives and provide a global perspective on the electric vehicle movement. This international knowledge-sharing network consists of the Electric Vehicles Initiative (EVI), a multi-government initiative of the Clean Energy Ministerial; Project Get Ready, a Rocky Mountain Institute (RMI

EV City Casebook: A Look At The Global Electric Vehicle Movement

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

Electric vehicles (EVs) hold the potential of transforming the way the world moves. EVs can increase energy security by diversifying the fuel mix and decreasing dependence on petroleum, while also reducing emissions of greenhouse gases and other pollutants. Just as important, EVs can unlock innovation and create new advanced industries that spur job growth and enhance economic prosperity. However, the mass deployment of EVs will require transportation systems capable of integrating and fostering this new technology. To accelerate this transition, cities and metropolitan regions around the world are creating EV-friendly ecosystems and building the foundation for widespread adoption. In recognition of the importance of urban areas in the introduction and scale-up of electric vehicles, the EV City Casebook presents informative case studies on city and regional EV deployment efforts around the world. These case studies are illustrative examples of how pioneering cities are preparing the ground for mass market EV deployment. They offer both qualitative and quantitative information on cities' EV goals, progress, policies, incentives, and lessons learned to date. The purpose of the EV City Casebook is to share experiences on EV demonstration and deployment, identify challenges and opportunities, and highlight best practices for creating thriving EV ecosystems. These studies seek to enhance understanding of the most effective policy measures to foster the uptake of electric vehicles in urban areas. The cities represented here are actively engaging in a variety of initiatives that share the goal of accelerating EV adoption. This publication is the result of an effort to coordinate those initiatives and provide a global perspective on the electric vehicle movement. This international knowledge-sharing network consists of the Electric Vehicles Initiative (EVI), a multi-government initiative of the Clean Energy Ministerial; Project Get Ready, a Rocky Mountain Institute

Potential Analysis of Electric Vehicle (EV) Grid Integration

DEFF Research Database (Denmark)

Wu, Qiuwei; Nielsen, Arne Hejde; Østergaard, Jacob

2011-01-01

Electric vehicles (EVs) have been considered as distributed energy resources (DER) to handle the fluctuation from renewable energy resources (RES), especially the wind power. The intelligent management of EV charging and discharging can achieve the goal of providing up and down regulating power...

Lithium-polymer batteries for EV applications. Final report

Energy Technology Data Exchange (ETDEWEB)

Thomas, J.O. [Uppsala Univ. (Sweden). Dept. of Inorganic Chemistry

2000-05-01

The project initially held a strong 'battery materials' profile, but has moved in its final year into more 'battery engineering' aspects; the performances of a range of potential materials have been screened, and candidates have emerged. It is noteworthy that these same materials have also now become 'best-choice' materials in commercial Japanese Li-ion batteries for mobile-phone, lap-top and, more recently, even electric-vehicle (EV) applications. It is now clear that the Li-ion (polymer) battery offers a genuinely viable option in electric and electric-hybrid vehicle concepts. Specifically, our work has involved synthetic, structural, morphological and electrochemical studies of lithium insertion mechanisms in TMO-based cathodes (LiMn{sub 2}O{sub 4}, V{sub 6}O{sub 13}, LiCoO{sub 2}, LiFePO{sub 4}, etc) and graphitic carbon anodes. Performance has been optimised from cell capacity, power, shelf-life and safety viewpoints. Cost has also emerged as a critical variable. Novel methods have been developed within the project for elevated-temperature battery studies (up to 80 deg C); they have become widely applied internationally. The electrode materials which have been developed have subsequently been incorporated into laboratory-scale lithium-ion battery prototypes, whose performance has then been evaluated. The final phase of the project has focussed on a new cathode material (LiFePO{sub 4}) not in current commercial use and yet ideally suited to EV application by virtue of its cheapness, high capacity (ca 170 mAh/g), high voltage vs. Li (3.5V), and extremely flat discharge curve. This could well prove to be the 'best compromise' Li-ion battery cathode for EV applications in the future.

Effects of hydration and oxygen vacancy on CO2 adsorption and activation on beta-Ga2O3(100).

Science.gov (United States)

Pan, Yun-xiang; Liu, Chang-jun; Mei, Donghai; Ge, Qingfeng

2010-04-20

The effects of hydration and oxygen vacancy on CO(2) adsorption on the beta-Ga(2)O(3)(100) surface have been studied using density functional theory slab calculations. Adsorbed CO(2) is activated on the dry perfect beta-Ga(2)O(3)(100) surface, resulting in a carbonate species. This adsorption is slightly endothermic, with an adsorption energy of 0.07 eV. Water is preferably adsorbed molecularly on the dry perfect beta-Ga(2)O(3)(100) surface with an adsorption energy of -0.56 eV, producing a hydrated perfect beta-Ga(2)O(3)(100) surface. Adsorption of CO(2) on the hydrated surface as a carbonate species is also endothermic, with an adsorption energy of 0.14 eV, indicating a slightly repulsive interaction when H(2)O and CO(2) are coadsorbed. The carbonate species on the hydrated perfect surface can be protonated by the coadsorbed H(2)O to a bicarbonate species, making the CO(2) adsorption exothermic, with an adsorption energy of -0.13 eV. The effect of defects on CO(2) adsorption and activation has been examined by creating an oxygen vacancy on the dry beta-Ga(2)O(3)(100) surface. The formation of an oxygen vacancy is endothermic, by 0.34 eV, with respect to a free O(2) molecule in the gas phase. Presence of the oxygen vacancy promoted the adsorption and activation of CO(2). In the most stable CO(2) adsorption configuration on the dry defective beta-Ga(2)O(3)(100) surface with an oxygen vacancy, one of the oxygen atoms of the adsorbed CO(2) occupies the oxygen vacancy site, and the CO(2) adsorption energy is -0.31 eV. Water favors dissociative adsorption at the oxygen vacancy site on the defective surface. This process is spontaneous, with a reaction energy of -0.62 eV. These results indicate that, when water and CO(2) are present in the adsorption system simultaneously, water will compete with CO(2) for the oxygen vacancy sites and impact CO(2) adsorption and conversion negatively.

Startup Ramp Rate Analysis for the OPR1000 Using FALCON Code

Energy Technology Data Exchange (ETDEWEB)

Kim, Ki-Young; Jung, Sung-hwan; Kim, Yong-Deok [Korea Hydro and Nuclear Power Co. Ltd, Daejeon (Korea, Republic of)

2015-05-15

Pelletcladding interaction (PCI) fuel failure results from a combination of mechanical and chemical interactions between the UO2 fuel pellets and Zircaloy cladding. Under restart operation conditions, the pellet-cladding gap may be closed and the differential thermal expansion can result in the stress concentrations on the cladding that may cause the fuel failure. This paper summarizes the PCI sensitivity assessment of the PLUS7 fuel during the OPR1000 startup. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. Fuel-cladding gap is closed at about 10,000 MWD/MTU burnup. Maximum hoop stress is not sensitive about change of startup ramp rate in 0 - 40% power range. Maximum hoop stress is not sensitive about the intermittent increase(1%) of startup ramp rate in 40 - 100% power range.

Startup Ramp Rate Analysis for the OPR1000 Using FALCON Code

International Nuclear Information System (INIS)

Kim, Ki-Young; Jung, Sung-hwan; Kim, Yong-Deok

2015-01-01

Pelletcladding interaction (PCI) fuel failure results from a combination of mechanical and chemical interactions between the UO2 fuel pellets and Zircaloy cladding. Under restart operation conditions, the pellet-cladding gap may be closed and the differential thermal expansion can result in the stress concentrations on the cladding that may cause the fuel failure. This paper summarizes the PCI sensitivity assessment of the PLUS7 fuel during the OPR1000 startup. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. Fuel-cladding gap is closed at about 10,000 MWD/MTU burnup. Maximum hoop stress is not sensitive about change of startup ramp rate in 0 - 40% power range. Maximum hoop stress is not sensitive about the intermittent increase(1%) of startup ramp rate in 40 - 100% power range

Inversion of electron-water elastic scattering data

International Nuclear Information System (INIS)

Lun, A.; Chen, X.J.; Allen, L.J.; Amos, K.

1994-01-01

Fixed energy inverse scattering theory has been used to analyse the differential cross-sections for the elastic scattering of electrons from water molecules. Both semiclassical (WKB) and fully quantal inversion methods have been used with data taken in the energy range 100 to 1000 eV. Constrained to be real, the local inversion potentials are found to be energy dependent; a dependence that can be interpreted as the local equivalence of true nonlocality in the actual interaction. 14 refs., 4 tabs., 8 figs

High reflectance Cr/C multilayer at 250 eV for soft X-ray polarimetry

Energy Technology Data Exchange (ETDEWEB)

Wen, Mingwu; Jiang, Li; Zhang, Zhong; Huang, Qiushi [MOE Key Laboratory of Advanced Micro-Structured Materials, Institute of Precision Optical Engineering (IPOE), School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); Wang, Zhanshan, E-mail: wangzs@tongji.edu.cn [MOE Key Laboratory of Advanced Micro-Structured Materials, Institute of Precision Optical Engineering (IPOE), School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); She, Rui; Feng, Hua [Department of Engineering Physics, Tsinghua University, Beijing (China); Wang, Hongchang [Diamond Light Source, Harwell Science and Innovation Campus, Didcot, Oxfordshire OX11 0DE (United Kingdom)

2015-10-01

X-ray reflection near 45° via multilayer mirrors can be used for astronomical polarization measurements. A Cr/C multilayer mirror (designed for X-ray polarimetry at 250 eV), with a period thickness of 3.86 nm and a bi-layer number of 100, was fabricated using direct current magnetron sputtering. Grazing incidence X-ray reflectometry at 8 keV and transmission electron microscopy were used to investigate the multilayer structure. Different models were introduced to fit the hard X-ray reflectivity curve, which indicates that the layer thickness of two materials slightly drifts from the bottom to the top of the stack. Both the chromium and carbon layers are amorphous with asymmetric interfaces, while the Cr-on-C interface is slightly wider. Based on the good quality of the multilayer structure, a high reflectivity of 21.8% for the s-polarized light was obtained at 250 eV at a grazing incidence angle of 40.7°. The fabricated Cr/C multilayer mirror exhibits high reflectivity and polarization levels in the energy region of 240 eV–260 eV. - Highlights: • We fabricated Cr/C multilayer with 3.8 nm d-spacing. • X-ray reflectometry was used to determine the exact structure of Cr/C multilayer. • A high reflectivity of 21.8% for the s-polarized light was obtained at 250 eV. • Both Cr and C were found to be amorphous with slightly asymmetric interfaces. • A 4-layer model was used to fit and explain the results.

Fachagentur Nachwachsende Rohstoffe e.V. (FNR). Annual report 1999/2000; Fachagentur Nachwachsende Rohstoffe e.V. (FNR). Jahresbericht 1999/2000

Energy Technology Data Exchange (ETDEWEB)

Schuette, A.

2001-07-01

The annual report of the Fachagentur Nachwachsende Rohstoffe e.V. outlines the state of the art and the boundary conditions of energy plant utilisation. The organisational struture of the association and its research projects are presented. [German] Der Jahresbericht der Fachagentur Nachwachsende Rohstoffe e.V. stellt Stand der Technik und Rahmenbedingungen fuer die Verwendung von Energiepflanzen dar. Die Organisation des Vereins sowie die gefoerderten Forschungsprojekte werden vorgestellt.

The dynamic range of ultra-high-resolution cryogenic gamma-ray spectrometers

Energy Technology Data Exchange (ETDEWEB)

Ali, Shafinaz [Advanced Detector Group, Lawrence Livermore National Laboratory, 7000 East Avenue, L-270, Livermore, CA 94550 (United States); Terracol, Stephane F. [Advanced Detector Group, Lawrence Livermore National Laboratory, 7000 East Avenue, L-270, Livermore, CA 94550 (United States); Drury, Owen B. [Advanced Detector Group, Lawrence Livermore National Laboratory, 7000 East Avenue, L-270, Livermore, CA 94550 (United States); Friedrich, Stephan [Advanced Detector Group, Lawrence Livermore National Laboratory, 7000 East Avenue, L-270, Livermore, CA 94550 (United States)]. E-mail: friedrich1@llnl.gov

2006-04-15

We are developing high-resolution cryogenic gamma-ray spectrometers for nuclear science and non-proliferation applications. The gamma-ray detectors are composed of a bulk superconducting Sn foil absorber attached to a multilayer Mo/Cu transition-edge sensor (TES). The energy resolution of a detector with a 1x1x0.25 mm{sup 3} Sn absorber is 50-90 eV FWHM for {gamma}-rays up to 100 keV, and it decreases for larger absorbers. Here, we present the detector performance for different absorber volumes, and discuss the trade-offs between energy resolution and dynamic range.

The Dynamic Range of Ultra-High Resolution Cryogenic Gamma-ray Spectrometers

International Nuclear Information System (INIS)

Ali, S; Terracol, S F; Drury, O B; Friedrich, S

2005-01-01

We are developing high-resolution cryogenic gamma-ray spectrometers for nuclear science and non-proliferation applications. The gamma-ray detectors are composed of a bulk superconducting Sn foil absorber attached to multilayer Mo/Cu transition-edge sensors (TES). The energy resolution achieved with a 1 x 1 x 0.25 mm 3 Sn absorber is 50 -90eV for γ-rays up to 100 keV and it decreases for large absorber sizes. We discuss the trade-offs between energy resolution and dynamic range, as well as development of TES arrays for higher count rates and better sensitivity

Immunological Evaluation and Comparison of Different EV71 Vaccine Candidates

Directory of Open Access Journals (Sweden)

Ai-Hsiang Chou

2012-01-01

Full Text Available Enterovirus 71 (EV71 and coxsackievirus A16 (CVA16 are major causative agents of hand, foot, and mouth diseases (HFMDs, and EV71 is now recognized as an emerging neurotropic virus in Asia. Effective medications and/or prophylactic vaccines against HFMD are not available. The current results from mouse immunogenicity studies using in-house standardized RD cell virus neutralization assays indicate that (1 VP1 peptide (residues 211–225 formulated with Freund’s adjuvant (CFA/IFA elicited low virus neutralizing antibody response (1/32 titer; (2 recombinant virus-like particles produced from baculovirus formulated with CFA/IFA could elicit good virus neutralization titer (1/160; (3 individual recombinant EV71 antigens (VP1, VP2, and VP3 formulated with CFA/IFA, only VP1 elicited antibody response with 1/128 virus neutralization titer; and (4 the formalin-inactivated EV71 formulated in alum elicited antibodies that cross-neutralized different EV71 genotypes (1/640, but failed to neutralize CVA16. In contrast, rabbits antisera could cross-neutralize strongly against different genotypes of EV71 but weakly against CVA16, with average titers 1/6400 and 1/32, respectively. The VP1 amino acid sequence dissimilarity between CVA16 and EV71 could partially explain why mouse antibodies failed to cross-neutralize CVA16. Therefore, the best formulation for producing cost-effective HFMD vaccine is a combination of formalin-inactivated EV71 and CAV16 virions.

Carbon disulfide (CS{sub 2}) adsorption and dissociation on the Cu(100) surface: A quantum chemical study

Energy Technology Data Exchange (ETDEWEB)

Wang, Wenju, E-mail: wangwenju1982@163.com; Fan, Lili; Wang, Guoping, E-mail: wgp1976@163.com

2017-08-31

Highlights: • CS{sub 2}, CS, C and S are strongly chemadsorbed on the Cu(100) surface. • C/S/S, S/CS and CS{sub 2} accord to a decreased adsorption strength on the Cu(100). • The asymmetric model CS{sub 2}(II) is easier to dissociate on the Cu(100) surface. - Abstract: Density functional theory (DFT) is used to examine the adsorption and dissociation of CS{sub 2} on the Cu(100) surface. This study evaluates the adsorption energies and geometries of the species (CS{sub 2}, CS, C and S) adsorption on the Cu(100) surface, as well as that coadsorption of CS and a S atom, and that coadsorption of C atom and two S atoms. The results indicate that the species (CS{sub 2}, CS, C and S) are strongly chemadsorbed on the Cu(100) surface through the C−Cu and/or S−Cu bond with an increased adsorption energy (C/S/S > S/CS > CS{sub 2}). Two pathways for CS{sub 2} dissociation on the Cu(100) surface are constructed, and the energy barrier and reaction energy of each step are calculated. It shows that the dissociated energy barrier of the second C−S bond is 0.25 eV higher than that of the first C−S bond in the pathway 1, but in the pathway 2, the dissociated energy barrier of the second C−S bond is 0.11 eV lower than that of the first C−S bond. Comparing the highest dissociated energy barrier of pathway 1 (0.68 eV) and pathway 2 (0.5 eV), the structure of S/C/S(II) is regarded as a preferable product for the dissociation of CS{sub 2} on the Cu(100) surface.

Primary loop simulation of the SP-100 space nuclear reactor

International Nuclear Information System (INIS)

Borges, Eduardo M.; Braz Filho, Francisco A.; Guimaraes, Lamartine N.F.

2011-01-01

Between 1983 and 1992 the SP-100 space nuclear reactor development project for electric power generation in a range of 100 to 1000 kWh was conducted in the USA. Several configurations were studied to satisfy different mission objectives and power systems. In this reactor the heat is generated in a compact core and refrigerated by liquid lithium, the primary loops flow are controlled by thermoelectric electromagnetic pumps (EMTE), and thermoelectric converters produce direct current energy. To define the system operation point for an operating nominal power, it is necessary the simulation of the thermal-hydraulic components of the space nuclear reactor. In this paper the BEMTE-3 computer code is used to EMTE pump design performance evaluation to a thermalhydraulic primary loop configuration, and comparison of the system operation points of SP-100 reactor to two thermal powers, with satisfactory results. (author)

Accurate e/sup -/-He cross sections below 19 eV

Energy Technology Data Exchange (ETDEWEB)

Nesbet, R K [International Business Machines Corp., San Jose, CA (USA). Research Lab.

1979-04-14

Variational calculations of e/sup -/-He s- and p-wave phaseshifts, together with the Born formula for higher partial waves, are used to give the scattering amplitude to within one per cent estimated accuracy for energies less than 19 eV. Coefficients are given of cubic spline fits to auxiliary functions that provide smooth interpolation of the estimated accurate phaseshifts. Data given here make it possible to obtain the differential scattering cross section over the energy range considered from simple formulae.

Analysis of operating reliability of WWER-1000 unit

International Nuclear Information System (INIS)

Bortlik, J.

1985-01-01

The nuclear power unit was divided into 33 technological units. Input data for reliability analysis were surveys of operating results obtained from the IAEA information system and certain indexes of the reliability of technological equipment determined using the Bayes formula. The missing reliability data for technological equipment were used from the basic variant. The fault tree of the WWER-1000 unit was determined for the peak event defined as the impossibility of reaching 100%, 75% and 50% of rated power. The period was observed of the nuclear power plant operation with reduced output owing to defect and the respective time needed for a repair of the equipment. The calculation of the availability of the WWER-1000 unit was made for different variant situations. Certain indexes of the operating reliability of the WWER-1000 unit which are the result of a detailed reliability analysis are tabulated for selected variants. (E.S.)

Production Facility Prototype Blower 1000 Hour Test Results II

Energy Technology Data Exchange (ETDEWEB)

Wass, Alexander Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Woloshun, Keith Albert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dale, Gregory E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dalmas, Dale Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Romero, Frank Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-08

Long duration tests of the Aerzen GM 12.4 roots style blower in a closed loop configuration provides valuable data and lessons learned for long-term operation at the Mo-99 production facility. The blower was operated in a closed loop configuration with the flow conditions anticipated in plant operation with a Mo-100 target inline. The additional thermal energy generated from beam heating of the Mo-100 disks were not included in these tests. Five 1000 hour tests have been completed since the first test was performed in January of 2016. All five 1000 hour tests have proven successful in exposing preventable issues related to oil and helium leaks. All blower tests to this date have resulted in stable blower performance and consistency. A summary of the results for each test, including a review of the first and second tests, are included in this report.

Optimal Operation of EVs and HPs in the Nordic Power System

DEFF Research Database (Denmark)

Liu, Zhaoxi

penetration level in the market environment. • The feasibility investigation of EVs and HPs to provide frequency reserves to the Nordic power system. To accomplish the researches mentioned above, the driving patterns of the vehicles in the Nordic region and the impacts of the EV and HP demand on the day...... that both EVs and HPs can provide considerable frequency reserves to the power system along the day in the Nordic region. Vehicle-to-Grid (V2G) technologies which enable the EVs to discharge the batteries in the reserve operations can further utilize the capacity of the EVs and consequently increase...

Comparison of CPR1000 and AP1000 rod position indication systems

International Nuclear Information System (INIS)

Lei Qing

2009-01-01

This paper introduces the structure, the function, the digital detection principle of reactor control rod position and monitoring systems in CPR1000 and AP1000, comparing with the characteristics of the system design. The results show that the operation mode and function of AP1000 Rod position indication system are similar to that of CPR1000, but AP1000 rod position system provides higher reliability, and reduces the numbers of containment electrical penetrations and is with better characteristics than that of CPR1000, since it incorporated the redundancy design and data communication. (authors)

The EV Project Price/Fee Models for Publicly Accessible Charging

Energy Technology Data Exchange (ETDEWEB)

Francfort, James Edward [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-12-01

As plug-in electric vehicles (PEVs) are introduced to the market place and gain more consumer acceptance, it is important for a robust and self-sustaining non-residential infrastructure of electric vehicle supply equipment (EVSE) to be established to meet the needs of PEV drivers. While federal and state financial incentives for electric vehicles were in place and remain so today, future incentives are uncertain. In order for PEVs to achieve mainstream adoption, an adequate and sustainable commercial or publicly available charging infrastructure was pursued by The EV Project to encourage increased PEV purchases by alleviating range anxiety, and by removing adoption barriers for consumers without a dedicated overnight parking location to provide a home-base charger. This included determining a business model for publicly accessible charge infrastructure. To establish this business model, The EV Project team created a fee for charge model along with various ancillary offerings related to charging that would generate revenue. And after placing chargers in the field the Project rolled out this fee structure.

Determination of morphology and electronic structure in solids with 20-1000 eV radiation

Energy Technology Data Exchange (ETDEWEB)

Denley, D.R.

1979-08-01

One of the most versatile probes for spectroscopy is the photon because it is readily tuned through a wide range of frequencies, it is chargeless, and because of the additional information available from its vector nature. With the advent of intense radiation light sources a nearly untouched region of the spectrum has become available for a wide range of new experiments. Two of the main techniques in use are those of absorption and photoemission. This thesis uses these techniques on a variety of different materials for the analysis of their morphology and electronic structure. The principles underlying the techniques of soft-x-ray absorption, bulk-, and surface-photoemission are discussed together with some of the experimental methods and instrumentation.

Determination of morphology and electronic structure in solids with 20-1000 eV radiation

International Nuclear Information System (INIS)

Denley, D.R.

1979-08-01

One of the most versatile probes for spectroscopy is the photon because it is readily tuned through a wide range of frequencies, it is chargeless, and because of the additional information available from its vector nature. With the advent of intense radiation light sources a nearly untouched region of the spectrum has become available for a wide range of new experiments. Two of the main techniques in use are those of absorption and photoemission. This thesis uses these techniques on a variety of different materials for the analysis of their morphology and electronic structure. The principles underlying the techniques of soft-x-ray absorption, bulk-, and surface-photoemission are discussed together with some of the experimental methods and instrumentation

Driving Pattern Analysis for Electric Vehicle (EV) Grid Integration Study

DEFF Research Database (Denmark)

Wu, Qiuwei; Nielsen, Arne Hejde; Østergaard, Jacob

2010-01-01

In order to facilitate the integration of electric vehicles (EVs) into the Danish power system, the driving data in Denmark were analyzed to extract the information of driving distances and driving time periods which were used to represent the driving requirements and the EV unavailability...... from the driving time periods to show how many cars are available for charging and discharging in each time period. The obtained EV availability data are in one hour time periods and one quarter time periods for different study purposes. The EV availability data of one hour time period are to be used...

Reflectance of Co- and Nb-doped BaTiO3 for photon energies from 1.8 to 70 eV

International Nuclear Information System (INIS)

Goudonnet, J.P.; Godefroy, G.; Inagaki, T.; Moretti, P.; Williams, M.W.; Arakawa, E.T.

1985-01-01

The reflectance spectra of Co- and Nb-doped BaTiO 3 crystals have been measured for photon energies from 1.8 to 70 eV. For both types of crystal, structures observed in the 1.8 to 2.3 eV range can be attributed to the presence of residual impurities. Between 2.3 and 3.2 eV the peaks in the reflectance of the Co-doped crystal are found to be of an acceptor charge transfer type. For Nb-doped crystals structures appear at the bottom of the conduction band. For energies larger than 3.2 eV the spectra are characteristic of pure BaTiO 3 crystals, in reasonable agreement with those determined by Baeuerle et al. and calculated by Michel-Calendini and Moretti. 15 refs., 4 figs., 1 tab

Assessment on Startup Ramp Rate and Threshold Power of OPR1000

Energy Technology Data Exchange (ETDEWEB)

Kim, Kiyoung; Kim, Yongbae; Cha, Gyunho; Kim, Yongdeog [Korea Hydro and Nuclear Power Co., Ltd., Daejeon (Korea, Republic of)

2014-05-15

This paper summarizes PCI assessment according to several startup ramp rates and threshold power assessment of OPR1000. The definition of threshold power is maximum value in power range that can increase startup ramp rate rapidly. FALCON code is used for PCI assessment and it is analyzed for once-burned fuel because it is the most sensitive to PCI failure. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. The PCI analyses were conducted for the once-burned fuel from the start of the second cycle to plant power 100%. This paper presents both the PCI analysis according to startup ramp rates and threshold power assessment result like below. · The more startup ramp rate is increased, the more PCI failure probability is decreased in low power range (≤ 40%). · PCI failure is not occurred even though startup ramp rate is 10%/hr until the plant power reaches 55%.

Assessment on Startup Ramp Rate and Threshold Power of OPR1000

International Nuclear Information System (INIS)

Kim, Kiyoung; Kim, Yongbae; Cha, Gyunho; Kim, Yongdeog

2014-01-01

This paper summarizes PCI assessment according to several startup ramp rates and threshold power assessment of OPR1000. The definition of threshold power is maximum value in power range that can increase startup ramp rate rapidly. FALCON code is used for PCI assessment and it is analyzed for once-burned fuel because it is the most sensitive to PCI failure. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. The PCI analyses were conducted for the once-burned fuel from the start of the second cycle to plant power 100%. This paper presents both the PCI analysis according to startup ramp rates and threshold power assessment result like below. · The more startup ramp rate is increased, the more PCI failure probability is decreased in low power range (≤ 40%). · PCI failure is not occurred even though startup ramp rate is 10%/hr until the plant power reaches 55%

Optimal Coordinated EV Charging with Reactive Power Support in Constrained Distribution Grids

Energy Technology Data Exchange (ETDEWEB)

Paudyal, Sumit; Ceylan, Oğuzhan; Bhattarai, Bishnu P.; Myers, Kurt S.

2017-07-01

Electric vehicle (EV) charging/discharging can take place in any P-Q quadrants, which means EVs could support reactive power to the grid while charging the battery. In controlled charging schemes, distribution system operator (DSO) coordinates with the charging of EV fleets to ensure grid’s operating constraints are not violated. In fact, this refers to DSO setting upper bounds on power limits for EV charging. In this work, we demonstrate that if EVs inject reactive power into the grid while charging, DSO could issue higher upper bounds on the active power limits for the EVs for the same set of grid constraints. We demonstrate the concept in an 33-node test feeder with 1,500 EVs. Case studies show that in constrained distribution grids in coordinated charging, average costs of EV charging could be reduced if the charging takes place in the fourth P-Q quadrant compared to charging with unity power factor.

The cosmic ray spectrum and composition measured by KASCADE-Grande between 10{sup 16} eV and 10{sup 18} eV

Energy Technology Data Exchange (ETDEWEB)

Bertaina, M., E-mail: bertaina@to.infn.it [Department of Physics, University of Torino and INFN, Torino (Italy); Apel, W.D. [Institut für Kernphysik, KIT – Karlsruher Institut für Technologie (Germany); Arteaga-Velázquez, J.C. [Institute of Physics and Mathematics, Universidad Michoacana de San Nicolas de Hidalgo, Morelia (Mexico); Bekk, K. [Institut für Kernphysik, KIT – Karlsruher Institut für Technologie (Germany); Blümer, J. [Institut für Kernphysik, KIT – Karlsruher Institut für Technologie (Germany); Institut für Experimentelle Kernphysik, KIT – Karlsruher Institut für Technologie (Germany); Bozdog, H. [Institut für Kernphysik, KIT – Karlsruher Institut für Technologie (Germany); Brancus, I.M. [Horia Hulubei National Institute of Physics and Nuclear Engineering, Bucharest (Romania); Cantoni, E. [Department of Physics, University of Torino and INFN, Torino (Italy); Osservatorio Astrofisico di Torino, INAF Torino (Italy); Chiavassa, A. [Department of Physics, University of Torino and INFN, Torino (Italy); Cossavella, F. [Institut für Experimentelle Kernphysik, KIT – Karlsruher Institut für Technologie (Germany); Daumiller, K. [Institut für Kernphysik, KIT – Karlsruher Institut für Technologie (Germany); Souza, V. de [Universidade São Paulo, Instituto de Física de São Carlos (Brazil); and others

2014-11-15

The shape and composition of the primary spectrum of cosmic rays are key elements to understand the origin, acceleration and propagation of the Galactic cosmic rays. Besides the well known knee and ankle features, the recent results of KASCADE-Grande indicate that the measured energy spectrum exhibits also a less pronounced but still clear deviation from a single power law between the knee and the ankle, with a spectral hardening at 2 × 10{sup 16} eV and a steepening at 10{sup 17} eV. The average mass composition gets heavier after the knee till 10{sup 17} eV where a bending of the heavy component is observed. An indication of a hardening of the light component just above 10{sup 17} eV has been measured as well. In this paper the major results obtained so far by the KASCADE-Grande experiment are reviewed.

Cosmic rays from 1017eV to beyond 1020eV: evidence from the fly's eye experiment and ground arrays.

Science.gov (United States)

Sokolsky, P.

The study of cosmic rays with energies well above the knee (1015eV) of the spectrum has a long history. Beginning with the pioneering work of Linsley and the Volcano Ranch array, followed by the SUGAR, Haverah Park, Yakutsk, Akeno and AGASA array and the Fly's Eye detector, evidence has been steadily accumulating that the spectrum exhibits a change in slope near 10×1018eV. This flattening may indicate that the spectrum in this region is largely extragalactic in origin. If the sources of this spectrum are sufficiently distant, a cut-off due to the interaction of near 1020eV protons with black body photons should be observed. Recent data from the AGASA and Fly's Eye detectors have brought to bear information of spectral shape, composition and anisotropy to this study. In addition to clarifying the nature of the spectral structure, these new results lead to the surprising conclusion that nearby cosmic ray sources must exist that produce particles with energies well in excess of 1020eV. New experiments are being designed which will have the enormous apertures necessary for detecting these very rare events.

Measurements of the total neutron cross-sections of U and UO2 below 2 eV at different temperatures

International Nuclear Information System (INIS)

Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Ashry, A.; Abbas, Y.; Abu-Zahra, A.; Hamouda, I.

1982-11-01

The total neutron cross-sections of natural uranium and its oxide are measured using two time of flight spectrometers, installed in front of two of the ET-RR-1 reactor horizontal channels, and also by a neutron diffraction spectrometer. The measurements were carried out at room temperature in the energy range from 2 eV-0.002 eV and at 210 deg. C, for neutron energies below 0.005 eV. The coherent scattering cross-section of U was deduced both from the Bragg cut-offs observed in the behaviour of the total neutron cross-section of both U and UO 2 at cold neutron energies and the neutron diffraction pattern obtained at room temperature. (author)

A positronium beam and positronium reflection from LiF(100)

International Nuclear Information System (INIS)

Weber, M.; Tang, S.; Berko, S.; Brown, B.L.; Canter, K.F.; Lynn, K.G.; Mills, A.P. Jr.; Roellig, L.O.; Viescas, A.J.

1988-01-01

We report results obtained from a variable energy monoenergetic beam of positronium (Ps). Ps was formed by a charge transfer reaction of positrons colliding with Ar gas atoms in a ''gas cell'' with an efficiency of about 3 /times/ 10/sup /minus/4/. The beam was used to measure the fraction, R, of specularly reflected ortho-Ps from LiF(100). We found R to peak at about 30% for 7 eV Ps at a specular scattering angle of 50/degree/ to 60/degree/. At higher energies R drops sharply to values around 0.5% near 60 eV Ps

The demonstration test of urban EV rental system with 'Hypermini'

Energy Technology Data Exchange (ETDEWEB)

Teramoto, M.; Tohyama, E.; Kasai, J. [Nissan Motor Co. Ltd., Tochigi (Japan); Takayama, M. [Electric Technology for Automobile Traffic and Driving Association, Tokyo (Japan)

2000-07-01

The efforts taken by the Electric Technology for Automobile Traffic and Driving Association to address environmental pollution associated with traffic jams were discussed. An urban electric vehicle (EV) rent-a-car system has been proposed which combines the intelligent transportation system (ITS) and ultra small EVs as a fourth public traffic system after rail, bus and taxis. A demonstration test of this system began in October 1999 with the Suzuki Motor Corporation. A total of 30 small conversion EV and 20 ultra small EVs, called the 'Hypermini' were tested in the heavily populated Yokohama Minato Mirai 21 District (MM21). The impetus for the feasibility study was the lack of transportation from residential areas to stations and from stations to business areas. The objective was to provide a seamless traffic system for door-to-door service and to improve the use of vehicle parking spaces by an intelligent car sharing system. Another objective was to reduce the operating cost of company cars in urban areas. A comprehensive description of how the urban rent-a-car system works was included along with an overview of the system components and a description of vehicle stations. The solution to one-way-trips was solved by employing people to either drive or tow dropped-off vehicles to their original stations. So far, most users are satisfied with the service. Those with complaints, argued that the range was not sufficient. It was emphasized that in order for the system to be accepted nation wide, it is important to maintain low costs and high reliability in this demonstration stage.

Energy distributions of H+ fragments ejected by fast proton and electron projectiles in collision with H2O molecules

International Nuclear Information System (INIS)

Barros, A. L. F. de; Lecointre, J.; Luna, H.; Montenegro, E. C.; Shah, M. B.

2009-01-01

Experimental measurements of the kinetic energy distribution spectra of H + fragment ions released during radiolysis of water molecules in collision with 20, 50, and 100 keV proton projectiles and 35, 200, 400, and 1000 eV electron projectiles are reported using a pulsed beam and drift tube time-of-flight based velocity measuring technique. The spectra show that H + fragments carrying a substantial amount of energy are released, some having energies well in excess of 20 eV. The majority of the ions lie within the 0-5 eV energy range with the proton spectra showing an almost constant profile between 1.5 and 5 eV and, below this, increasing gradually with decreasing ejection energy up to the near zero energy value while the electron spectra, in contrast, show a broad maximum between 1 and 3 eV and a pronounced dip around 0.25 eV. Beyond 5 eV, both projectile spectra show a decreasing profile with the electron spectra decreasing far more rapidly than the proton spectra. Our measured spectra thus indicate that major differences are present in the collision dynamics between the proton and the electron projectiles interacting with gas phase water molecules.

Analysis method and utilization mechanism of the overall value of EV charging

International Nuclear Information System (INIS)

Guo, Chunlin; Chan, Ching Chuen

2015-01-01

Highlights: • Analysis on the overall value of EV charging from a viewpoint of system. • An analytical model of the overall value of EV charging was presented. • A model was proposed to calculate the value of emission reduction by EV. • A model to evaluate the improvement in new energy utilization was given. • A utilization mechanism apt to overall optimization was proposed. - Abstract: Electric Vehicle (EV) can save energy while reducing emissions and has thus attracted the attention of both academics and industry. The cost and benefit of charging are one of the key issues in relation to EV development that has been researched extensively. But many studies are carried out from a viewpoint of some local entities rather than a global system, focus on specific types or aspects of EV charging, or use mixed models that can only be computed by computer simulation and lack physical transparency. This paper illuminated that it is necessary to consider the value of EV charging on a system scale. In order to achieve this, it presents an analytical model for analyzing the overall value of EVs, an analysis model to evaluate the reduction of pollutions relevant to photovoltaic power, and a model to transfer the intrinsic savings of wind power to the off-peak charging loads. It is estimated that EV charging has a significant positive value, providing the basis for enhanced EV subsidies. Accordingly, a utilization mechanism apt to optimize globally is proposed, upon which sustainable business models can be formed by providing adequate support, including the implementation of a peak–valley tariff, charging subsidies and one-time battery subsidies. This utilization mechanism, by taking full advantage of the operation system of power utilities to provide basic support and service, may provide new approaches to the development of EVs. The method proposed here is of important value for the systematic considerations about EV development and maybe can help broaden the

Adopting Strategic Niche Management to Evaluate EV Demonstration Projects in China

Directory of Open Access Journals (Sweden)

Yixi Xue

2016-02-01

Full Text Available Electric Vehicles (EVs are considered to be a potential viable technology to address the persistent unsustainable problems in transport sector. In this paper, we focus on analyzing the transition processes of EVs in China because the sustainability of developing countries is essential for the worldwide sustainability. The two-round demonstration programs of EVs in China were analyzed by adopting the strategic niche management (SNM approach so as to find out what niche protection has been provided and which obstacles hamper the further development of EVs. The results show that the financial subsidy is the most important protective measure. However, the diffusion results of EVs in different pilot cities are greatly different. The main reason lies in the uneven geographical landscape. In addition, some obstacles were exposed during the niche internal processes including low quality of expectations and poor alignment within the network. Based on the analysis results, we develop a list of suggestions that are important to consider when developing EVs.

Research on alternative measures in the F1000 system with Google Scholar citation index

OpenAIRE

Saeideh Ebrahimy; Fatemeh Setareh

2016-01-01

The purpose of this study was to assess the relationship between altmetrics measures of F1000 website and citation Indexes of Google scholar. Applied research and survey methods, citation analysis, and webometrics with descriptive analytical approach are used. The study population comprised 218 biomedical research papers have been indexed in F1000 system in the period 2012-2014. A sample of 100 research articles were purposely selected from F1000 system based on the purpose of the research. V...

Simulation of laser propagation through a three-layer human skin model in the spectral range from 1000 to 1900 nm

Science.gov (United States)

Nasouri, Babak; Murphy, Thomas E.; Berberoglu, Halil

2014-07-01

For understanding the mechanisms of low-level laser/light therapy (LLLT), accurate knowledge of light interaction with tissue is necessary. We present a three-dimensional, multilayer reduced-variance Monte Carlo simulation tool for studying light penetration and absorption in human skin. Local profiles of light penetration and volumetric absorption were calculated for uniform as well as Gaussian profile beams with different spreads over the spectral range from 1000 to 1900 nm. The results showed that lasers within this wavelength range could be used to effectively and safely deliver energy to specific skin layers as well as achieve large penetration depths for treating deep tissues, without causing skin damage. In addition, by changing the beam profile from uniform to Gaussian, the local volumetric dosage could increase as much as three times for otherwise similar lasers. We expect that this tool along with the results presented will aid researchers in selecting wavelength and laser power in LLLT.

Difference of reactor core nuclear instrument between AP1000 and CPR1000

International Nuclear Information System (INIS)

Zhang Shidong; Zhou Can; Deng Tian

2014-01-01

As a typical generation Ⅲ reactor technique, the AP1000 applies many advanced design concepts, simplifies the design, reduces equipment quantities, and thus enhances systematic reliability. The comparison of reactor core measurement instrument differences between AP1000 and CPR1000 from several aspects was involved in the paper. Through analysis and comparison of these differences, passive design concepts and characteristics of AP1000 are familiarized, and conveniences for staffs engaged in CPR1000 to learn and grasp AP1000 technique are provided. It is useful in reactor start up, operation and maintenance. (authors)

Joint absorption of lithium and oxygen on the tungsten (100) face

International Nuclear Information System (INIS)

Gupalo, M.S.; Smereka, T.P.; Babkin, G.V.; Palyukh, B.M.

1981-01-01

The paper deals with studying the effect of oxygen on emission-adsorption properties of metal-film Li-W system. Data on work of phi yield and adsorption heat q of lithium on tungsten face (100), preliminarily coated with different quantity of oxygen, are obtained. The method of contact potential difference was used. Strong decrease of yield work with the increase of oxygen coatings, as well as essential growth of initial adsorption heat are observed. Temperature dependence of phi is not practically observed. The data obtained point out, that oxygen presence on the surface causes increase of dipole momentum of lithium adatoms, which results in bond energy growth and reduction phi minimal value of lithium in the presence of oxygen phi=2 eV, q=2.2 eV is obtained at optimal compositions of oxygen-lithium layers on W (100) [ru

Storage Application in Smart Grid with High PV and EV Penetration

DEFF Research Database (Denmark)

Hashemi Toghroljerdi, Seyedmostafa; Yang, Guangya; Østergaard, Jacob

2013-01-01

grids with residential PVs and Electric Vehicles (EVs). The effect of EV home charging on EESS capacity in high PV penetration is also addressed. The results indicate that increasing the EV penetration in the network can decrease the EESS capacity need. This decrease is highest in situations with low PV...

L1000CDS2: LINCS L1000 characteristic direction signatures search engine.

Science.gov (United States)

Duan, Qiaonan; Reid, St Patrick; Clark, Neil R; Wang, Zichen; Fernandez, Nicolas F; Rouillard, Andrew D; Readhead, Ben; Tritsch, Sarah R; Hodos, Rachel; Hafner, Marc; Niepel, Mario; Sorger, Peter K; Dudley, Joel T; Bavari, Sina; Panchal, Rekha G; Ma'ayan, Avi

2016-01-01

The library of integrated network-based cellular signatures (LINCS) L1000 data set currently comprises of over a million gene expression profiles of chemically perturbed human cell lines. Through unique several intrinsic and extrinsic benchmarking schemes, we demonstrate that processing the L1000 data with the characteristic direction (CD) method significantly improves signal to noise compared with the MODZ method currently used to compute L1000 signatures. The CD processed L1000 signatures are served through a state-of-the-art web-based search engine application called L1000CDS 2 . The L1000CDS 2 search engine provides prioritization of thousands of small-molecule signatures, and their pairwise combinations, predicted to either mimic or reverse an input gene expression signature using two methods. The L1000CDS 2 search engine also predicts drug targets for all the small molecules profiled by the L1000 assay that we processed. Targets are predicted by computing the cosine similarity between the L1000 small-molecule signatures and a large collection of signatures extracted from the gene expression omnibus (GEO) for single-gene perturbations in mammalian cells. We applied L1000CDS 2 to prioritize small molecules that are predicted to reverse expression in 670 disease signatures also extracted from GEO, and prioritized small molecules that can mimic expression of 22 endogenous ligand signatures profiled by the L1000 assay. As a case study, to further demonstrate the utility of L1000CDS 2 , we collected expression signatures from human cells infected with Ebola virus at 30, 60 and 120 min. Querying these signatures with L1000CDS 2 we identified kenpaullone, a GSK3B/CDK2 inhibitor that we show, in subsequent experiments, has a dose-dependent efficacy in inhibiting Ebola infection in vitro without causing cellular toxicity in human cell lines. In summary, the L1000CDS 2 tool can be applied in many biological and biomedical settings, while improving the extraction of

SP-100 nuclear space power systems with application to space commercialization

International Nuclear Information System (INIS)

Smith, J.M.

1988-01-01

The purpose of this paper is to familiarize the Space Commercialization Community with the status and characteristics of the SP-100 space nuclear power system. The program is a joint undertaking by the Department of Defense, the Department of Energy and NASA. The goal of the program is to develop, validate, and demonstrate the technology for space nuclear power systems in the range of 10 to 1000 kWe electric for use in the future civilian and military space missions. Also discussed are mission applications which are enhanced and/or enabled by SP-100 technology and how this technology compares to that of more familiar solar power systems. The mission applications include earth orbiting platforms and lunar/Mars surface power

Towards 10 meV resolution: The design of an ultrahigh resolution soft X-ray RIXS spectrometer.

Science.gov (United States)

Dvorak, Joseph; Jarrige, Ignace; Bisogni, Valentina; Coburn, Scott; Leonhardt, William

2016-11-01

We present the optical design of the Centurion soft X-ray resonant inelastic X-ray scattering (RIXS) spectrometer to be located on the SIX beamline at NSLS-II. The spectrometer is designed to reach a resolving power of 100 000 at 1000 eV at its best resolution. It is also designed to have continuously variable 2θ motion over a range of 112° using a custom triple rotating flange. We have analyzed several possible spectrometer designs capable of reaching the target resolution. After careful analysis, we have adopted a Hettrick-Underwood spectrometer design, with an additional plane mirror to maintain a fixed direction for the outgoing beam. The spectrometer can cancel defocus and coma aberrations at all energies, has an erect focal plane, and minimizes mechanical motions of the detector. When the beamline resolution is accounted for, the net spectral resolution will be 14 meV at 1000 eV. This will open up many low energy excitations to study and will expand greatly the power of soft X-ray RIXS.

Towards 10 meV resolution: The design of an ultrahigh resolution soft X-ray RIXS spectrometer

Science.gov (United States)

Dvorak, Joseph; Jarrige, Ignace; Bisogni, Valentina; Coburn, Scott; Leonhardt, William

2016-11-01

We present the optical design of the Centurion soft X-ray resonant inelastic X-ray scattering (RIXS) spectrometer to be located on the SIX beamline at NSLS-II. The spectrometer is designed to reach a resolving power of 100 000 at 1000 eV at its best resolution. It is also designed to have continuously variable 2θ motion over a range of 112° using a custom triple rotating flange. We have analyzed several possible spectrometer designs capable of reaching the target resolution. After careful analysis, we have adopted a Hettrick-Underwood spectrometer design, with an additional plane mirror to maintain a fixed direction for the outgoing beam. The spectrometer can cancel defocus and coma aberrations at all energies, has an erect focal plane, and minimizes mechanical motions of the detector. When the beamline resolution is accounted for, the net spectral resolution will be 14 meV at 1000 eV. This will open up many low energy excitations to study and will expand greatly the power of soft X-ray RIXS.

Outgassing tests on graphites in temperature range 100-1600 degrees C

International Nuclear Information System (INIS)

Alessandrini, C.; Apicella, M.L.; Verdini, L.

1993-01-01

Graphite is a an interesting material for plasma-facing components in fusion experiments, mainly because of its low atomic number and excellent thermal properties. Nevertheless, it contains a large amount of gaseous impurities, which can be released by plasma-surface interactions and affect the purity of the deuterium-tritium plasma. To investigate the outgassing behaviour of graphites, CFC's and doped C composites, a facility was set up to perform outgassing tests on samples, as a function of temperature in the range between 100 and 1600 degrees C. The experimental apparatus, designed to work in UHV conditions, allows outgassing measurements by a quadrupole mass spectrometer (1-200 AMU) using two different methods. The test facility, the quadrupole calibration and preliminary quantitative outgassing measurements on SEP CARB N112 samples are described

Correlation between blister skin thickness, the maximum in the damage-energy distribution, and projected ranges of He+ ions in metals: V

International Nuclear Information System (INIS)

Kaminsky, M.; Das, S.K.; Fenske, G.

1976-01-01

In these experiments a systematic study of the correlation of the skin thickness measured directly by scanning electron microscopy with both the calculated projected-range values and the maximum in the damage-energy distribution has been conducted for a broad helium-ion energy range (100 keV-1000 keV in polycrystalline vanadium. (Auth.)

A multipolar SR motor and its application in EV

International Nuclear Information System (INIS)

Goto, H.; Suzuki, Y.; Nakamura, K.; Watanabe, T.; Guo, H.J.; Ichinokura, O.

2005-01-01

In order to bring out the advanced features of EVs, a direct-drive (DD) with in-wheel (IW) layout has been considered, but it requires more motors than the conventional layout and the motors will be used in a hard environment. Because switched reluctance motors (SRMs) are simple and strong, we have developed a new outer-rotor-type multipolar SRM suitable for DD-IW EVs through simulations and experiments. We have implemented the developed SRMs into a prototype EV. This is the first-ever in-vehicle research to our knowledge; the developing process and the road test results will bring many useful guidelines for future developments

Base fluid in improving heat transfer for EV car battery

Science.gov (United States)

Bin-Abdun, Nazih A.; Razlan, Zuradzman M.; Shahriman, A. B.; Wan, Khairunizam; Hazry, D.; Ahmed, S. Faiz; Adnan, Nazrul H.; Heng, R.; Kamarudin, H.; Zunaidi, I.

2015-05-01

This study examined the effects of base fluid (as coolants) channeling inside the heat exchanger in the process of the increase in thermal conductivity between EV car battery and the heat exchanger. The analysis showed that secondary cooling system by means of water has advantages in improving the heat transfer process and reducing the electric power loss on the form of thermal energy from batteries. This leads to the increase in the efficiency of the EV car battery, hence also positively reflecting the performance of the EV car. The present work, analysis is performed to assess the design and use of heat exchanger in increasing the performance efficiency of the EV car battery. This provides a preface to the use this design for nano-fluids which increase and improve from heat transfer.

SiO mass spectrometry and Si-2p photoemission spectroscopy for the study of oxidation reaction dynamics of Si(001) surface by supersonic O sub 2 molecular beams under 1000K

CERN Document Server

Teraoka, Y; Moritani, K

2003-01-01

The Si sup 1 sup 8 O desorption yield was measured in the Si(001) surface temperature region from 900K to 1300K at the sup 1 sup 8 O sub 2 incident energies of 0.7eV, 2.2eV and 3.3eV. The Si sup 1 sup 8 O desorption yield in a surface temperature region higher than 1000K increased with increasing incident energy, indicating the incident-energy-induced oxidation and the variation of angular distribution of Si sup 1 sup 8 O desorption. Inversely, the Si sup 1 sup 8 O desorption yield decreased with increasing incident energy in the region from 900K to 1000K, indicating the coexistence of the passive and the active oxidation. In order to clarify the reaction mechanisms of the later phenomenon, real-time in-situ Si-2p photoemission spectroscopy has been performed. The obtained Si-2p spectra showed the variation of the oxide-nuclei quality from the sub-oxide-rich structure to the SiO sub 2 -rich structure. The formation of the SiO sub 2 structure suppresses the SiO desorption due to the enhanced O sub 2 sticking a...

Straight and chopped DC performance data for a reliance EV-250AT motor with a General Electric EV-1 controller

Science.gov (United States)

Edie, P. C.

1981-01-01

Straight and chopped DC motor performances for a Reliance EV-250AT motor with an EV-1 controller were examined. Effects of motor temperature and operating voltage are shown. It is found that the maximum motor efficiency is approximately 85% at low operating temperatures in the straight DC mode. Chopper efficiency is 95% under all operating conditions. For equal speeds, the motor operated in the chopped mode develops slightly more torque and draws more current than it does in the straight DC mode.

The nature of the Esub(v) + 0.23 eV and Esub(v) + 0.38 eV gamma-induced centres in Ge

International Nuclear Information System (INIS)

Pearton, S.J.; Tavendale, A.J.

1982-07-01

All p-type Ge grown by the Czochralski technique from silica crucibles under an H 2 atmosphere shows two dominant acceptor defects on γ irradiation. Measurements by DLTS are reported which support the hypothesis that these centres (Esub(v) + 0.23 eV, Esub(v) + 0.38 eV) are most likely due to complexes between oxygen and lattice vacancies

Concentration of WWER-1000 unit power on one site

International Nuclear Information System (INIS)

Rousek, J.; Kysel, J.; Sladek, V.

1987-01-01

The problem of a suitable number of nuclear power plant units built on one site is discussed. Using an example of three sites being prepared now in Czechoslovakia, two alternatives - one with two WWER-1000 units, the other with four WWER-1000 units on one site - are evaluated from the viewpoint of long-range nuclear power development program in Czechoslovakia, costs, transmission of electric power and heat supply. (author). 10 tabs., 13 refs

Delayed Diagnosis, Range of Severity, and Multiple Sleep Comorbidities: A Clinical and Polysomnographic Analysis of 100 Patients of the Innsbruck Narcolepsy Cohort

Science.gov (United States)

Frauscher, Birgit; Ehrmann, Laura; Mitterling, Thomas; Gabelia, David; Gschliesser, Viola; Brandauer, Elisabeth; Poewe, Werner; Högl, Birgit

2013-01-01

Study Objectives: Narcolepsy is reported to affect 26-56/100,000 in the general population. We aimed to describe clinical and polysomnographic features of a large narcolepsy cohort in order to comprehensively characterize the narcoleptic spectrum. Methods: We performed a chart- and polysomnographybased review of all narcolepsy patients of the Innsbruck narcolepsy cohort. Results: A total of 100 consecutive narcolepsy patients (87 with cataplexy [NC], 13 without cataplexy [N]) were included in the analysis. All subjects had either excessive daytime sleepiness or cataplexy as their initial presenting clinical feature. Age at symptom onset was 20 (6-69) years. Diagnostic delay was 6.5 (0-39) years. The complete narcolepsy tetrad was present in 36/100 patients; 28/100 patients had three cardinal symptoms; 29/100 had two; and 7/100 had only excessive daytime sleepiness. Severity varied broadly with respect to excessive daytime sleepiness (median Epworth Sleepiness Scale score: 18, range 10-24), cataplexy (8-point Likert scale: median 4.5, range 1-8), hypnagogic hallucinations (median 4.5, range 1-7), and sleep paralysis (median 3, range 1-7). Sleep comorbidity was highly prevalent and ranged from sleeprelated movement disorders (n = 55/100), parasomnias (n = 34/100), and sleeprelated breathing disorders (n = 24/100), to insomnia (n = 28/100). REM sleep without atonia or a periodic limb movement in sleep index > 5/h were present in most patients (90/100 and 75/100). A high percentage of narcoleptic patients in the present study had high frequency leg movements (35%) and excessive fragmentary myoclonus (22%). Of the narcolepsy patients with clinical features of REM sleep behavior disorder (RBD), 76.5% had EMG evidence for RBD on the multiple sleep latency test (MSLT), based on a standard cutoff of a minimum of 18% of 3-sec miniepochs. Conclusion: This study is one of the largest monocentric polysomnographic studies to date of patients with narcolepsy and confirms the

A Decentralized Model for Coordinated Operation of Distribution Network and EV Aggregators

DEFF Research Database (Denmark)

Mohiti, Maryam; Mazidi, Mohammadreza; Monsef, Hassan

2018-01-01

With the rapid growth of electrical vehicles (EVs) in distribution networks (DNs), EV aggregators have been introduced as mediators between these two entities. EV aggregators and DN should be operated coordinately to bring potential benefits to both sides. In this paper, a decentralized model...

EV integration in smart grids through interoperability solutions

OpenAIRE

Rodríguez-Sánchez, Raúl; Madina, Carlos; Zabala, Eduardo

2015-01-01

The high total cost of ownership and the uncertainties surrounding battery reliability are still the main barriers for electric vehicle (EV) market take off in Europe. Storage evolution, leading to both price reduction and performance improvement, is a huge technical challenge in the medium-long term. In the meantime, new business models and market niche developments might play a facilitator role for EV deployment by tackling the economic gap between conventional ICE and electromobility (e-mo...

Adsorption of nitrogen on W(100): effect of surface disorder on the work function change

International Nuclear Information System (INIS)

Singh-Bofarai, S.P.; King, D.A.

1976-01-01

At room temperature nitrogen adsorption causes the work function of the (100) plane of tungsten to decrease by approximately 0.6 eV, while on all other planes the work function is increased, albeit by as little as 0.03 eV on the (110) plane. Surface disorder can readily be created by the vapour deposition of W onto a clean, annealed W single crystal surface, and in the present work this technique was used to shadow a W field emission tip with disordered W atoms so as to observe the effect of surface disorder on the work function change due to nitrogen adsorption, particularly at the (100) poles of the tip. (Auth.)

Electron-photon angular correlation measurements of He (1 1S0-2 1P1) excitation by electron impact at 80 eV

International Nuclear Information System (INIS)

Steph, N.C.; Golden, D.E.

1980-01-01

The electron-photon angular correlation function was measured between 80-eV electrons which excited the 2 1 P 1 state of helium and 58.4-nm photons from the decay of that state for electron scattering angles ranging from 5 0 to 100 0 . The data have been analyzed to yield values of the ratio lambda of the differential cross section for exciting the M/sub j/=0 sublevel to the total differential cross section and the magnitude vertical-barchivertical-bar of the phase difference between the M/sub j/=0 and M/sub j/=1 excitation amplitudes. The data agree with all previous measurements within one standard deviation, with the exception of the large-angle values of lambda obtained by Hollywood, Crowe, and Williams. Possible causes of these discrepancies are discussed. The values of lambda and vertical-barchivertical-bar obtained in this work agree quite well with those given by the distorted-wave calculations of Madison over the entire angular range

11 CFR 100.137 - Invitations, food, and beverages.

Science.gov (United States)

2010-01-01

... 11 Federal Elections 1 2010-01-01 2010-01-01 false Invitations, food, and beverages. 100.137...) Exceptions to Expenditures § 100.137 Invitations, food, and beverages. The cost of invitations, food, and... invitations, food and beverages provided by the individual on behalf of the candidate does not exceed $1,000...

11 CFR 100.77 - Invitations, food, and beverages.

Science.gov (United States)

2010-01-01

... 11 Federal Elections 1 2010-01-01 2010-01-01 false Invitations, food, and beverages. 100.77...) Exceptions to Contributions § 100.77 Invitations, food, and beverages. The cost of invitations, food and... invitations, food and beverages provided by the individual on behalf of the candidate does not exceed $1,000...

A re-evaluation of the initial yield of the hydrated electron in the picosecond time range

International Nuclear Information System (INIS)

Muroya, Yusa; Lin Mingzhang; Wu, Guozhong; Iijima, Hokuto; Yoshii, Koji; Ueda, Toru; Kudo, Hisaaki; Katsumura, Yosuke

2005-01-01

The yield of the hydrated electron in the picosecond time range has been re-evaluated with an ultrafast pulse radiolysis system using a laser photocathode RF-gun in combination with a conventional one, and a value of 4.1±0.2 per 100 eV of absorbed energy at 20 ps was derived. This is consistent with recent experimental results using a time correlation method [Bartels et al., J. Phys. Chem. A 104, 1686-1691 (2000)] and with Monte-Carlo calculations [Muroya et al., Can. J. Chem. 80 1367-1374 (2002)

Evaluation of the capture cross section of natural Ti from 10-5eV to 20.106eV

International Nuclear Information System (INIS)

Simon, G.; Bersillon, O.; Mosinski, G.; Philis, C.; Trochon, J.; Verges, N.

1977-01-01

In the 10 -5 eV - 200 keV energy range a coherent resolved resonance parameter set has been determined for each titanium isotope. From these sets the titanium capture cross section has been calculated with the Reich-Moore formalism and corrected for the missing resonances. From 200 keV up to 20 MeV all the isotopic cross sections were calculated with the help of two statistical model codes NCNR and FISPRO. These calculations have been adjusted on available 50 Ti(n,γ) 51 Ti and Ti(n,γ) experimental results. The elemental titanium capture cross section has been obtained as the weighted sum of the isotopic cross sections. The present evaluation is descriptive of the experimental values. The comparison of the present evaluation with ENDF/BIV shows the ameliorations brought in this cross section: a better description of all the resonances known in the 1 keV - 200 keV energy range; above 200 keV the new data give a more realistic shape showing compound nucleus competition of prominent inelastic scattering channels. As titanium is used as structural material for fast reactors the capture cross section integrals for the two evaluations in different energy ranges are compared. These comparisons show considerable discrepancies in some areas. Thus the new evaluation may change the results of reactor calculations

Performance Analysis of Permanent Magnet Motors for Electric Vehicles (EV Traction Considering Driving Cycles

Directory of Open Access Journals (Sweden)

Thanh Anh Huynh

2018-05-01

Full Text Available This paper evaluates the electromagnetic and thermal performance of several traction motors for electric vehicles (EVs. Two different driving cycles are employed for the evaluation of the motors, one for urban and the other for highway driving. The electromagnetic performance to be assessed includes maximum motor torque output for vehicle acceleration and the flux weakening capability for wide operating range under current and voltage limits. Thermal analysis is performed to evaluate the health status of the magnets and windings for the prescribed driving cycles. Two types of traction motors are investigated: two interior permanent magnet motors and one permanent magnet-assisted synchronous reluctance motor. The analysis results demonstrate the benefits and disadvantages of these motors for EV traction and provide suggestions for traction motor design. Finally, experiments are conducted to validate the analysis.

NREL/Industry Range-Extended Electric Vehicle for Package Delivery

Energy Technology Data Exchange (ETDEWEB)

Farrell, John T [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kelly, Kenneth J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Duran, Adam W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Lammert, Michael P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Miller, Eric S [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-01-15

Range-extended electric vehicle (EV) technology can be a viable option for reducing fuel consumption from medium-duty (MD) and heavy-duty (HD) engines by approximately 50 percent or more. Such engines have wide variations in use and duty cycles, however, and identifying the vocations/duty cycles most suitable for range-extended applications is vital for maximizing the potential benefits. This presentation provides information about NREL's research on range-extended EV technologies, with a focus on NREL's real-world data collection and analysis approach to identifying the vocations/duty cycles best suited for range-extender applications and to help guide related powertrain optimization and design requirements. The presentation also details NREL's drive cycle development process as it pertains to package delivery applications.

Introduction of electric double layer capacitors in the solar-EV; Solar denki jidosha eno denki nijuso condenser no oyo

Energy Technology Data Exchange (ETDEWEB)

Fujinaka, M [Tokyo Denki University, Tokyo (Japan)

1996-10-27

A basic experiment was carried out on a supplementary power supply, in which solar cells and electric double layer capacitors(EDLC) were combined for a DC/DC converter, for the use of a solar-electric vehicle (S-EV); and in actuality, an S-EV was loaded with the power supply with a running test conducted on a public road. The EDLC was found effective and useful for avoiding temporary lowering of voltage and momentary break. An electric supply was thereby made possible for an emergency light without the use of the DC/DC converter. However, in a tunnel or a night driving and in case of failure of the DC/DC converter, an operating time of only 7 minutes or so was affordable with the EDLC having a capacity of 100F. Moreover, particularly with a heavy load, it was impossible to maintain a voltage for many hours. Under the circumstances, an S-EV design would primarily require two sets of independent DC/DC converter loaded in the future. The EDLC, young after it was developed, still has a small energy density compared with a lead storage battery. Yet, an EDLC with a higher performance being developed, there is a possibility that it will be applied to S-EV`s by utilizing its characteristics such as a high efficiency and a long service life. 4 refs., 8 figs.

Retrospective study of the incidence of HFMD and seroepidemiology of antibodies against EV71 and CoxA16 in prenatal women and their infants.

Directory of Open Access Journals (Sweden)

Feng-Cai Zhu

Full Text Available Hand, foot, and mouth disease (HFMD has been emerging as an important public problem over the past few decades, especially in Asian and Pacific regions. A national program on EV71 vaccine development against HFMD was initiated in China, in 2008, which called for a need for seroepidemiological study for the target population.This was a retrospective study conducted in Jiangsu Province, in October, 2010. We measured the neutralizing antibodies against EV71 and CoxA16 in a cohort of infants aged of 2, 7, 12, and 27-38 months and their mothers just before delivery. Series sera samples from 975 infants and 555 mothers were collected and analyzed. Questionnaires on the history of HFMD were completed in the survey. A total of 143 HFMD cases were collected, but only 11.2% were reported to the National Infectious Disease Information Management System. The level of maternal antibody titers decreased dramatically during the first 7 month and remained at a relatively low level thereafter. But it increased significantly from month 12 to months 27-38. The accumulate incidence density of HFMD demonstrated a significant increase after 14 months of age, resulting in a accumulate incidence density of 50.8/1000 person-years in survey period. Seropositivity of EV71 antibody in infants at the age of 2 months seems to demonstrate a protective effect against HFMD.High seropositive rate of EV71 and CoxA16 antibody was found in prenatal women in mainland China, and there is a need to enhance the HFMD case management and the current surveillance system. We suggest that infants aged between 6 to 14 months should have the first priority to receive EV71 vaccine.

Fabrication of n-ZnO/ p-Si (100) and n-ZnO:Al/ p-Si (100) Heterostructures and Study of Current-Voltage, Capacitance-Voltage and Room-Temperature Photoluminescence

Science.gov (United States)

Shah, M. A. H.; Khan, M. K. R.; Tanveer Karim, A. M. M.; Rahman, M. M.; Kamruzzaman, M.

2018-01-01

Heterojunction diodes of n-ZnO/ p-Si (100) and n-ZnO:Al/ p-Si (100) were fabricated by spray pyrolysis technique. X-ray diffraction (XRD), energy dispersive x-ray spectroscopy (EDX), and field emission scanning electron microscopy (FESEM) were used to characterize the as-prepared samples. The XRD pattern indicates the hexagonal wurzite structure of zinc oxide (ZnO) and Al-doped ZnO (AZO) thin films grown on Si (100) substrate. The compositional analysis by EDX indicates the presence of Al in the AZO structure. The FESEM image indicates the smooth and compact surface of the heterostructures. The current-voltage characteristics of the heterojunction confirm the rectifying diode behavior at different temperatures and illumination intensities. For low forward bias voltage, the ideality factors were determined to be 1.24 and 1.38 for un-doped and Al-doped heterostructures at room temperature (RT), respectively, which indicates the good diode characteristics. The capacitance-voltage response of the heterojunctions was studied for different oscillation frequencies. From the 1/ C 2- V plot, the junction built-in potentials were found 0.30 V and 0.40 V for un-doped and Al-doped junctions at RT, respectively. The differences in built-in potential for different heterojunctions indicate the different interface state densities of the junctions. From the RT photoluminescence (PL) spectrum of the n-ZnO/ p-Si (100) heterostructure, an intense main peak at near band edge (NBE) 378 nm (3.28 eV) and weak deep-level emissions (DLE) centered at 436 nm (2.84 eV) and 412 nm (3.00 eV) were observed. The NBE emission is attributed to the radiative recombination of the free and bound excitons and the DLE results from the radiative recombination through deep level defects.

OECD/DOE/CEA VVER-1000 Coolant Transient Benchmark. Summary Record of the Fourth Workshop (V100-CT4)

International Nuclear Information System (INIS)

2006-01-01

The overall objective of the VVER-1000 coolant transient (V1000CT) benchmark is to assess computer codes used in the safety analysis of VVER power plants, specifically for their use in analysis of reactivity transients in a VVER-1000. The V1000CT benchmark consists of two phases: V1000CT-1 is a simulation of the switching on of one main coolant pump (MCP) when the other three MCPs are in operation, and V1000CT-2 concerns calculation of coolant mixing tests and main steam line break (MSLB) scenarios. Each of the two phases contains three exercises. The reference problem chosen for simulation in Phase 1 is a MCP switching on when the other three main coolant pumps are in operation in a VVER-1000. This event is characterized by rapid increase in the flow through the core resulting in a coolant temperature decrease, which is spatially dependent. This leads to insertion of spatially distributed positive reactivity due to the modelled feedback mechanisms and non-symmetric power distribution. Simulation of the transient requires evaluation of core response from a multi-dimensional perspective (coupled three-dimensional neutronics/core thermal-hydraulics) supplemented by a one-dimensional simulation of the remainder of the reactor coolant system. Three exercises are defined in the framework of Phase 1: a) Exercise 1 - Point kinetics plant simulation; b) Exercise 2 - Coupled 3-D neutronics/core thermal-hydraulics response evaluation; c) Exercise 3 - Best-estimate coupled 3-D core/plant system transient modelling. In addition to the measured (experiment) scenario, extreme calculation scenarios were defined in the frame of Exercise 3 for better testing 3-D neutronics/thermal-hydraulics techniques. The proposals concerned: rod ejection simulations with scram set points at two different power levels. Since the previous coupled code benchmarks indicated that further development of the mixing computation models in the integrated codes is necessary, a coolant mixing experiment and

Interaction of polarized neutrons with polarized La nuclei and the structure of the cross section at energies up to 20 eV

International Nuclear Information System (INIS)

Alfimenkov, V.P.; Mareev, Yu.D.; Novitskii, V.V.; Pikel'ner, L.B.; Skoi, V.R.

1994-01-01

Properties of lanthanum are investigated in an experiment on the interaction of polarized neutrons with polarized La nuclei. The total cross section for lanthanum is measured for neutron energies ranging from 0.4 to 10 eV. It is shown that one strong level below the neutron binding energy is sufficient for obtaining a good description of the lanthanum cross section in this energy range. The results on the cross section for the interaction of polarized projectiles on a polarized target confirm this conclusion. The spin of the 138 La neutron resonance at 3.0 eV is found to be J = 11 / 2 . 13 refs., 3 figs

Horizontal steam generator PGV-1000 thermal-hydraulic analysis

Energy Technology Data Exchange (ETDEWEB)

Ubra, O. [Skoda Company, Prague (Switzerland); Doubek, M. [Czech Technical Univ., Prague (Switzerland)

1995-12-31

A computer program for the steady state thermal-hydraulic analysis of horizontal steam generator PGV-1000 is presented. The program provides the capability to analyze steam generator PGV-1000 primary side flow and temperature distribution, primary side pressure drops, heat transfer between the primary and secondary sides and multidimensional heat flux distribution. A special attention is paid to the thermal-hydraulics of the secondary side. The code predicts 3-D distribution of the void fraction at the secondary side, mass redistribution under the submerged perforated sheet and the steam generator level profile. By means of developed computer program a detailed thermal-hydraulic study of the PGV-1000 has been carried out. A wide range of calculations has been performed and a set of important steam generator characteristics has been obtained. Some of them are presented in the paper. (orig.). 5 refs.

Horizontal steam generator PGV-1000 thermal-hydraulic analysis

International Nuclear Information System (INIS)

Ubra, O.; Doubek, M.

1995-01-01

A computer program for the steady state thermal-hydraulic analysis of horizontal steam generator PGV-1000 is presented. The program provides the capability to analyze steam generator PGV-1000 primary side flow and temperature distribution, primary side pressure drops, heat transfer between the primary and secondary sides and multidimensional heat flux distribution. A special attention is paid to the thermal-hydraulics of the secondary side. The code predicts 3-D distribution of the void fraction at the secondary side, mass redistribution under the submerged perforated sheet and the steam generator level profile. By means of developed computer program a detailed thermal-hydraulic study of the PGV-1000 has been carried out. A wide range of calculations has been performed and a set of important steam generator characteristics has been obtained. Some of them are presented in the paper. (orig.)

Horizontal steam generator PGV-1000 thermal-hydraulic analysis

Energy Technology Data Exchange (ETDEWEB)

Ubra, O [Skoda Company, Prague (Switzerland); Doubek, M [Czech Technical Univ., Prague (Switzerland)

1996-12-31

A computer program for the steady state thermal-hydraulic analysis of horizontal steam generator PGV-1000 is presented. The program provides the capability to analyze steam generator PGV-1000 primary side flow and temperature distribution, primary side pressure drops, heat transfer between the primary and secondary sides and multidimensional heat flux distribution. A special attention is paid to the thermal-hydraulics of the secondary side. The code predicts 3-D distribution of the void fraction at the secondary side, mass redistribution under the submerged perforated sheet and the steam generator level profile. By means of developed computer program a detailed thermal-hydraulic study of the PGV-1000 has been carried out. A wide range of calculations has been performed and a set of important steam generator characteristics has been obtained. Some of them are presented in the paper. (orig.). 5 refs.

Sputtering of carbon using hydrogen ion beams with energies of 60–800 eV

Energy Technology Data Exchange (ETDEWEB)

Sidorov, Dmitry S., E-mail: dmitrisidoroff@rambler.ru [Nizhny Novgorod State University, 23 Gagarina Avenue, Nizhny Novgorod, Nizhny Novgorod Region 603950 (Russian Federation); Chkhalo, Nikolay I., E-mail: chkhalo@ipm.sci-nnov.ru [Institute for Physics of Microstructures RAS, Academicheskaya Str. 7, Afonino, Nizhny Novgorod Region, Kstovsky District, Kstovo Region 603087 (Russian Federation); Mikhailenko, Mikhail S.; Pestov, Alexey E.; Polkovnikov, Vladimir N. [Institute for Physics of Microstructures RAS, Academicheskaya Str. 7, Afonino, Nizhny Novgorod Region, Kstovsky District, Kstovo Region 603087 (Russian Federation)

2016-11-15

This article presents the result of a study on the sputtering of carbon films by low-energy hydrogen ions. In particular, the etching rate and surface roughness were measured. The range of energies where the sputtering switches from pure chemical to a combination of chemical and physical mechanisms was determined. It is shown that Sigmund’s theory for ion etching does not work well for fields of energy less than 150 eV and that it accurately describes the dependence of a sputtering coefficient on ion energy for energies greater than 300 eV. A strong smoothing effect for the surface of carbon film was also found. This result is interesting in itself and for its significance for the manufacture of super-smooth surfaces for X-ray applications.

Ion beam generated modes in the lower hybrid frequency range in a laboratory magnetoplasma

Science.gov (United States)

Van Compernolle, B.; Tripathi, S.; Gekelman, W. N.; Colestock, P. L.; Pribyl, P.

2012-12-01

The generation of waves by ion ring distributions is of great importance in many instances in space plasmas. They occur naturally in the magnetosphere through the interaction with substorms, or they can be man-made in ionospheric experiments by photo-ionization of neutral atoms injected perpendicular to the earth's magnetic field. The interaction of a fast ion beam with a low β plasma has been studied in the laboratory. Experiments were performed at the LArge Plasma Device (LAPD) at UCLA. The experiments were done in a Helium plasma (n ≃ 1012 \\ cm-3, B0 = 1000 G - 1800 G, fpe}/f{ce ≃ 1 - 5, Te = 0.25\\ eV, vte ≤ vA). The ion beam \\cite{Tripathi_ionbeam} is a Helium beam with energies ranging from 5 keV to 18 keV. The fast ion velocity is on the order of the Alfvén velocity. The beam is injected from the end of the machine, and spirals down the linear device. Waves were observed below fci in the shear Alfvén wave regime, and in a broad spectrum above fci in the lower hybrid frequency range, the focus of this paper. The wave spectra have distinct peaks close to ion cyclotron harmonics, extending out to the 100th harmonic in some cases. The wave generation was studied for various magnetic fields and background plasma densities, as well as for different beam energies and pitch angles. The waves were measured with 3-axis electric and magnetic probes. Detailed measurements of the perpendicular mode structure will be shown. Langmuir probes were used to measure density and temperature evolution due to the beam-plasma interaction. Retarding field energy analyzers captured the ion beam profiles. The work was performed at the LArge Plasma Device at the Basic Plasma Science Facility (BaPSF) at UCLA, funded by DOE/NSF.

Developing of the EV charging and parking shed of BIPV

Institute of Scientific and Technical Information of China (English)

Wu Shaobo; Wei Chuanchuan; Yu Jiang

2013-01-01

Building-integrated photovoltaic (BIPV) is an important application way of solar photovoltaic power. The electric vehicle (EV) charging and parking shed of BIPV is the regeneration energy intellectual integration demonstration application system collection of photovoltaic (PV) grid power,PV off-grid power,EV charging and parking shed,and any part of the functions and their combination will be engaged in practical application on demand. The paper describes the PV shed system structure and design in detail with the present of its actual photos. The shed is 50 m long and 5.5 m wide and capable of parking 18 cars. Under the control of system intellectual con-troller,the power produced by PV from sunlight will charge the parking EV car prior to charging the storage bat-tery,charging the storage battery prior to grid power,grid power at last,and charge the EV by utility grid when it is a cloudy or rainy day.

Global EV Outlook: Understanding the Electric Vehicle Landscape to 2020

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-06-01

The Global EV Outlook represents the collective efforts of two years of primary data gathering and analysis from the Electric Vehicles Initiative (EVI) and IEA. Key takeaways and insights include landscape analysis of electric vehicle (EV) stock/sales and charging station deployment. Existing policy initiatives are delineated and future opportunities highlighted in an ''Opportunity Matrix: Pathways to 2020''. Together EVI countries accounted for more than 90% of world EV stock at the end of 2012. Strong government support in EVI countries on both the supply and demand sides are contributing to rising market penetration. 12 out of 15 EVI countries offer financial support for vehicle purchases, and most employ a mix of financial and non-financial incentives (such as access to restricted highway lanes) to help drive adoption. The Global EV Outlook is a unique and data-rich overview of the state of electric vehicles today, and offers an understanding of the electric vehicle landscape to 2020.

Modeling and Testing of EVs - Preliminary Study and Laboratory Development

DEFF Research Database (Denmark)

Yang, Guang-Ya; Marra, Francesco; Nielsen, Arne Hejde

2010-01-01

Electric vehicles (EVs) are expected to play a key role in the future energy management system to stabilize both supply and consumption with the presence of high penetration of renewable generation. A reasonably accurate model of battery is a key element for the study of EVs behavior and the grid...... tests, followed by the suggestions towards a feasible battery model for further studies.......Electric vehicles (EVs) are expected to play a key role in the future energy management system to stabilize both supply and consumption with the presence of high penetration of renewable generation. A reasonably accurate model of battery is a key element for the study of EVs behavior and the grid...... impact at different geographical areas, as well as driving and charging patterns. Electric circuit model is deployed in this work to represent the electrical properties of a lithium-ion battery. This paper reports the preliminary modeling and validation work based on manufacturer data sheet and realistic...

Global EV Outlook: Understanding the Electric Vehicle Landscape to 2020

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-06-01

The Global EV Outlook represents the collective efforts of two years of primary data gathering and analysis from the Electric Vehicles Initiative (EVI) and IEA. Key takeaways and insights include landscape analysis of electric vehicle (EV) stock/sales and charging station deployment. Existing policy initiatives are delineated and future opportunities highlighted in an ''Opportunity Matrix: Pathways to 2020''. Together EVI countries accounted for more than 90% of world EV stock at the end of 2012. Strong government support in EVI countries on both the supply and demand sides are contributing to rising market penetration. 12 out of 15 EVI countries offer financial support for vehicle purchases, and most employ a mix of financial and non-financial incentives (such as access to restricted highway lanes) to help drive adoption. The Global EV Outlook is a unique and data-rich overview of the state of electric vehicles today, and offers an understanding of the electric vehicle landscape to 2020.

Molecular beam (1-50eV) production by duoplasmatron source

International Nuclear Information System (INIS)

Delmas, M.; Gautherin, G.; Lejeune, C.

1974-01-01

The duoplasmatron discharge is commonly used to produce intense ion beams. A theoretical model of this discharge has been previously developed. The analysis of charge exchange processes between ions and neutral within the discharge shows that the source is able to deliver intense neutral beams (10 16 part s -1 ), the energy being in the range 1-50 eV. The intensity and energy distribution may be controlled from the discharge parameter variations. An experimental device has been realized in order to separate the neutral beam and the flux of charged particles; these latter are injected axially in a toroidal magnetic field configuration [fr

Range performance calculations using the NVEOL-Georgia Tech Research Institute 0.1- to 100-GHz radar performance model

Science.gov (United States)

Rodak, S. P.; Thomas, N. I.

1983-05-01

A computer model that can be used to calculate radar range performance at any frequency in the 0.1-to 100-GHz electromagnetic spectrum is described. These different numerical examples are used to demonstrate how to use the radar range performance model. Input/output documentation are included for each case that was run on the MERADCOM CDC 6600 computer at Fort Belvoir, Virginia.

MOCVD of hexagonal boron nitride thin films on Si(100) using new single source precursors

CERN Document Server

Boo, J H; Yu, K S; Kim, Y S; Kim, Y S; Park, J T

1999-01-01

We have been carried out the growth of hexagonal boron nitride (h-BN) thin films on Si(100) substrates by low pressure metal-organic chemical vapor deposition (LPMOCVD) method using triethylborane tert-butylamine complex (TEBTBA), Et sub 3 BNH sub 2 ( sup t Bu), and triethylborane isopropylamine complex (TEBIPA), Et sub 3 BNH sub 2 ( sup t Pr) as a new single molecular precursors in the temperature range of 850 approx 1000 .deg. C. polycrystalline, crack-free h-BN film was successfully grown on Si(100) substrate at 850 .deg. C using TEBTBA. This growth temperature is very lower than those in previous reports. Carbon-rich polycrystalline BN was also obtained at 900 .deg. C from TEBIPA. With increasing substrate temperature to 1000 .deg. C, however, BC sub 4 N-like species are strongly formed along with h-BN and the BN films obtained from both TEBTBA and TEBIPA but almost polycrystalline. To our best knowledge, this is the first report of the growth of h-BN films formed with the new single source precursors of ...

Lowering the density of electronic defects on organic-functionalized Si(100) surfaces

International Nuclear Information System (INIS)

Peng, Weina; DeBenedetti, William J. I.; Kim, Seonjae; Chabal, Yves J.; Hines, Melissa A.

2014-01-01

The electrical quality of functionalized, oxide-free silicon surfaces is critical for chemical sensing, photovoltaics, and molecular electronics applications. In contrast to Si/SiO 2 interfaces, the density of interface states (D it ) cannot be reduced by high temperature annealing because organic layers decompose above 300 °C. While a reasonable D it is achieved on functionalized atomically flat Si(111) surfaces, it has been challenging to develop successful chemical treatments for the technologically relevant Si(100) surfaces. We demonstrate here that recent advances in the chemical preparation of quasi-atomically-flat, H-terminated Si(100) surfaces lead to a marked suppression of electronic states of functionalized surfaces. Using a non-invasive conductance-voltage method to study functionalized Si(100) surfaces with varying roughness, a D it as low as 2.5 × 10 11  cm −2 eV −1 is obtained for the quasi-atomically-flat surfaces, in contrast to >7 × 10 11  cm −2 eV −1 on atomically rough Si(100) surfaces. The interfacial quality of the organic/quasi-atomically-flat Si(100) interface is very close to that obtained on organic/atomically flat Si(111) surfaces, opening the door to applications previously thought to be restricted to Si(111)

Comparative Analysis of Technologies for Quantifying Extracellular Vesicles (EVs in Clinical Cerebrospinal Fluids (CSF.

Directory of Open Access Journals (Sweden)

Johnny C Akers

Full Text Available Extracellular vesicles (EVs have emerged as a promising biomarker platform for glioblastoma patients. However, the optimal method for quantitative assessment of EVs in clinical bio-fluid remains a point of contention. Multiple high-resolution platforms for quantitative EV analysis have emerged, including methods grounded in diffraction measurement of Brownian motion (NTA, tunable resistive pulse sensing (TRPS, vesicle flow cytometry (VFC, and transmission electron microscopy (TEM. Here we compared quantitative EV assessment using cerebrospinal fluids derived from glioblastoma patients using these methods. For EVs 150 nm in diameter, NTA consistently detected lower number of EVs relative to TRPS. These results unveil the strength and pitfalls of each quantitative method alone for assessing EVs derived from clinical cerebrospinal fluids and suggest that thoughtful synthesis of multi-platform quantitation will be required to guide meaningful clinical investigations.

The generalized Yablonskii-Vorob'ev polynomials and their properties

International Nuclear Information System (INIS)

Kudryashov, Nikolai A.; Demina, Maria V.

2008-01-01

Rational solutions of the generalized second Painleve hierarchy are classified. Representation of the rational solutions in terms of special polynomials, the generalized Yablonskii-Vorob'ev polynomials, is introduced. Differential-difference relations satisfied by the polynomials are found. Hierarchies of differential equations related to the generalized second Painleve hierarchy are derived. One of these hierarchies is a sequence of differential equations satisfied by the generalized Yablonskii-Vorob'ev polynomials

Fluence-to-absorbed-dose conversion coefficients for neutron beams from 0.001 eV to 100 GeV calculated for a set of pregnant female and fetus models

International Nuclear Information System (INIS)

Taranenko, Valery; Xu, X George

2008-01-01

Protection of fetuses against external neutron exposure is an important task. This paper reports a set of absorbed dose conversion coefficients for fetal and maternal organs for external neutron beams using the RPI-P pregnant female models and the MCNPX code. The newly developed pregnant female models represent an adult female with a fetus including its brain and skeleton at the end of each trimester. The organ masses were adjusted to match the reference values within 1%. For the 3 mm cubic voxel size, the models consist of 10-15 million voxels for 35 organs. External monoenergetic neutron beams of six standard configurations (AP, PA, LLAT, RLAT, ROT and ISO) and source energies 0.001 eV-100 GeV were considered. The results are compared with previous data that are based on simplified anatomical models. The differences in dose depend on source geometry, energy and gestation periods: from 20% up to 140% for the whole fetus, and up to 100% for the fetal brain. Anatomical differences are primarily responsible for the discrepancies in the organ doses. For the first time, the dependence of mother organ doses upon anatomical changes during pregnancy was studied. A maximum of 220% increase in dose was observed for the placenta in the nine months model compared to three months, whereas dose to the pancreas, small and large intestines decreases by 60% for the AP source for the same models. Tabulated dose conversion coefficients for the fetus and 27 maternal organs are provided

76 FR 6541 - Airworthiness Directives; Fokker Services B.V. Model F.28 Mark 0100, 1000, 2000, 3000, and 4000...

Science.gov (United States)

2011-02-07

... Airworthiness Directives; Fokker Services B.V. Model F.28 Mark 0100, 1000, 2000, 3000, and 4000 Airplanes AGENCY.... Applicability (c) This AD applies to Fokker Services B.V. Model F.28 Mark 1000, 2000, 3000, and 4000 airplanes... April 20, 2010 (for Model F.28 Mark 1000, 2000, 3000, and 4000 airplanes); or SBF100-28-063, dated April...

Experimental investigation on EV battery cooling and heating by heat pipes

International Nuclear Information System (INIS)

Wang, Q.; Jiang, B.; Xue, Q.F.; Sun, H.L.; Li, B.; Zou, H.M.; Yan, Y.Y.

2015-01-01

Enhancing battery safety and thermal behaviour are critical for electric vehicles (EVs) because they affect the durability, energy storage, lifecycle, and efficiency of the battery. Prior studies of using air, liquid or phase change materials (PCM) to manage the battery thermal environment have been investigated over the last few years, but only a few take heat pipes into account. This paper aims to provide a full experimental characterisation of heat pipe battery cooling and heating covering a range of battery ‘off-normal’ conditions. Two representative battery cells and a substitute heat source ranging from 2.5 to 40 W/cell have been constructed. Results show that the proposed method is able to keep the battery surface temperature below 40 °C if the battery generates less than 10 W/cell, and helps reduce the battery temperature down to 70 °C under uncommon thermal abuse conditions (e.g. 20–40 W/cell). Additionally, the feasibility of using sintered copper-water heat pipes under sub-zero temperatures has been assessed experimentally by exposing the test rig to −15 °C/−20 °C for more than 14 h. Data indicates that the heat pipe was able to function immediately after long hours of cold exposure and that sub-zero temperature conditions had little impact on heat pipe performance. We therefore conclude that the proposed method of battery cooling and heating via heat pipes is a viable solution for EVs

Charge your electric vehicle when driving?; Rijdend je EV opladen?

Energy Technology Data Exchange (ETDEWEB)

Ishii, M.

2012-07-05

In late June 2012 a team of Japanese Toyota and ToyohashiUniversity of Technology (TUT) successfully developed and demonstrated a new induction charging method for electric vehicles (EV) [Dutch] Eind junidemonstreerde een Japans team van Toyota en ToyohashiUniversity of Technology (TUT) met succes een nieuwe inductie oplaadmethode voor elektrisch vervoer (EV)

Diagnostic capability of 100-mm roll film digitizer system

International Nuclear Information System (INIS)

Kono, M.; Yamasaki, K.; Ikeda, M.

1988-01-01

The authors recently developed a roll film digitizer system. The sampling pitch is 100 μm. a scientific image study (Barger phantom, Hawlet chart, and modulation transfer function), receiver operating characteristic (ROC) study, and clinical evaluation were performed. For the ROC study, a chest phantom with simulated nodule and hairline was used. Differences in accuracy between readings of cathode ray tube (CRT) images and roll film images were not statistically significant for hairline and coin lesions, P<.05). As a clinical evaluation, eight radiologists evaluated predetermined radiologic findings on a five-point rating scale compared with original roll film images. Scores for CRT images were equal to those for the original roll film images. In conclusion, CRT images (1,000 x 1,000) were found to be sufficient for diagnostic accuracy of chest images compared with roll film images (100 x 100 mm)

Neutron widths for 236U from high resolution transmission measurements at a 100M flightpath

International Nuclear Information System (INIS)

Carraro, G.; Brusegan, A.

1975-01-01

A series of neutron transmission measurements has been performed on 236 U aiming at a determination of the resonance parameters and their statistical properties. The analysis range covered neutron energies from 40eV to 4.1 keV. The experiments were carried out at about 100 m flightpath of the 80 MeV electron linear accelerator of CBNM using a 10 B slab-NaI detector and 2 236 U-oxyde samples on loan from the USAEC. A table displays the details of 6 experimental runs, 3 of which were arranged in such a way that the effect of the 235 U and 238 U impurities in the sample on the transmission was automatically compensated

Taras Ševčenko in the Prose and Poetry of Vasyl’ Stus

Directory of Open Access Journals (Sweden)

Alessandro Achilli

2016-02-01

Full Text Available The presence of Ševčenko in the poetry of Vasyl’ Stus and Stus’s widespread stereotypical image as a reincarnation of Ševčenko in the 20th century have occupied an important role in both literary studies and popularization. In my article I reconsider this fundamental issue by discussing Stus’s reception of Ševčenko in his critical essays, his letters, and his poetry. My focus is on both Ševčenko’s presence as a ‘fictional character’ in some poems by Stus and the overall influence of Ševčenko’s poetry on Stus’s poetic writing. Moreover, Stus’s representation of Ševčenko is compared with other images of the 19th-century poet in modern Ukrainian poetry from the Avant-garde up to the Seventies. In the conclusion I point out how Ševčenko’s Romanticism should not be confused with Stus’s Modernism. The former should be seen as a part of the complex intertextual mechanism which lies at the heart of Stus’s poetry.

Nanostructuring-Induced Modification of optical Properties of p-GaAs (100)

International Nuclear Information System (INIS)

Naddaf, M.; Saloum, S.

2010-01-01

A pulsed anodic etching method has been utilized for nano structuring of p-type GaAs(100) surface, using HCl-based solution as electrolyte. The resulting porous GaAs layer is characterized by atomic force etched GaAs, a strong green PL band is observed in the etched sample. The broad visible PL band of high-energy (3.82 eV) excitation is found to compose of tow PL band attributed to excitons confinement in tow different sizes distribution of GaAs nano crystals. The quantum confinement effects in GaAs nano crystallites are also evidenced from Raman spectroscopy through the pronounced appearance of the transverse optical (TO) phonon line in the spectra of the porous sample.Porosity-induced a significant reduction of the specular reflection, in the spectral range (400-800 nm), is also demonstrated. (author)

Technique for increasing dynamic range of space-borne ion composition instruments

International Nuclear Information System (INIS)

Burch, J.L.; Miller, G.P.; Santos, A. de los; Pollock, C.J.; Pope, S.E.; Valek, P. W.; Young, D.T.

2005-01-01

The dynamic range of ion composition spectrometers is limited by several factors, including saturation of particle counters and spillover of signals from highly dominant species into channels tuned to minor species. Instruments designed for composition measurements of hot plasmas in space can suffer greatly from both of these problems because of the wide energy range required and the wide disparity in fluxes encountered in various regions of interest. In order to detect minor ions in regions of very weak fluxes, geometry factors need to be as large as possible within the mass and volume resources available. As a result, problems with saturation by the dominant fluxes and spillover to minor-ion channels in plasma regions with intense fluxes become especially acute. This article reports on a technique for solving the dynamic-range problem in the few eV to several keV energy/charge range that is of central importance for space physics research where the dominant ion is of low mass/charge (typically H + ), and the minor ions are of higher mass/charge (typically O + ). The technique involves employing a radio-frequency modulation of the deflection electric field in the back section of an electrostatic analyzer in a time-of-flight instrument. This technique is shown to reduce H + counts by a controllable amount of up to factors of 1000 while reducing O + counts by only a few percent that can be calibrated

Shift of Enterovirus species among children in Cameroon--identification of a new enterovirus, EV-A119.

Science.gov (United States)

Ayukekbong, James; Kabayiza, Jean-Claude; Lindh, Magnus; Nkuo-Akenji, Theresia; Tah, Ferdinand; Bergström, Tomas; Norder, Helene

2013-09-01

Infections caused by human enteroviruses (EVs) are often asymptomatic or mild, although they may cause more severe illnesses as meningitis and acute flaccid paralysis. EVs have globally posed a threat to children, and outbreaks of aseptic meningitis and hand, foot and mouth disease are frequently reported. To identify EV strains circulating among healthy children in a small community in Limbe, Cameroon two years apart. Species and EV types were obtained by partial 5'UTR-VP4 and VP1 sequencing of RNA from stool samples collected in October 2009 and September 2011 from 150 children in Cameroon. In all, 74 children (49%) were infected with 28 different types of EV. There were 29 (54%) infected children in 2009, and 45 (47%) in 2011. There was a significant difference between detected species of EV, with 15 (47%) children infected with EV-A in 2009, and 22 (71%) with EV-B in 2011 (p=0.0001). In 2009, one child was infected by a divergent EV, which was most similar to EV-A90. Based on the complete VP1 sequence, it was shown to be a new EV designated EV-A119. The current study shows a high heterogeneity of circulating EV types among children in Limbe, Cameroon, and a previously not described shift in predominating EV species. Copyright © 2013 Elsevier B.V. All rights reserved.

Caspase-3 Inhibition Attenuates the Cytopathic Effects of EV71 Infection

Directory of Open Access Journals (Sweden)

Fengmei Song

2018-04-01

Full Text Available Previous studies demonstrate that human enterovirus 71 (EV71, a primary causative agent for hand, foot, and mouth disease, activates caspase-3 through the non-structural viral 3C protein to induce host cell apoptosis; however, until now it was unclear how 3C activates caspase-3 and how caspase-3 activation affects viral production. Our results demonstrate that 3C binds caspase-8 and caspase-9 but does not directly bind caspase-3 to activate them, and that the proteolytic activity of 3C is required by the activation of caspase-8, caspase-9, and caspase-3. Inhibition of caspase-3 activity attenuates apoptosis in 3C-transfected cells. Furthermore, caspase-3 inhibitor protects host cells from the cytopathic effect of EV71 infection and prevents cell cycle arrest, which is known to be favored for EV71 viral replication. Inhibition of caspase-3 activity decreases EV71 viral protein expression and viral production, but has no effect on viral entry, replication, even polyprotein translation. Therefore, caspase-3 is exploited functionally by EV71 to facilitate its production, which suggests a novel therapeutic approach for the treatment and prevention of hand, foot, and mouth disease.

Management Approach for NASA's Earth Venture-1 (EV-1) Airborne Science Investigations

Science.gov (United States)

Guillory, Anthony R.; Denkins, Todd C.; Allen, B. Danette

2013-01-01

The Earth System Science Pathfinder (ESSP) Program Office (PO) is responsible for programmatic management of National Aeronautics and Space Administration's (NASA) Science Mission Directorate's (SMD) Earth Venture (EV) missions. EV is composed of both orbital and suborbital Earth science missions. The first of the Earth Venture missions is EV-1, which are Principal Investigator-led, temporally-sustained, suborbital (airborne) science investigations costcapped at $30M each over five years. Traditional orbital procedures, processes and standards used to manage previous ESSP missions, while effective, are disproportionally comprehensive for suborbital missions. Conversely, existing airborne practices are primarily intended for smaller, temporally shorter investigations, and traditionally managed directly by a program scientist as opposed to a program office such as ESSP. In 2010, ESSP crafted a management approach for the successful implementation of the EV-1 missions within the constructs of current governance models. NASA Research and Technology Program and Project Management Requirements form the foundation of the approach for EV-1. Additionally, requirements from other existing NASA Procedural Requirements (NPRs), systems engineering guidance and management handbooks were adapted to manage programmatic, technical, schedule, cost elements and risk. As the EV-1 missions are nearly at the end of their successful execution and project lifecycle and the submission deadline of the next mission proposals near, the ESSP PO is taking the lessons learned and updated the programmatic management approach for all future Earth Venture Suborbital (EVS) missions for an even more flexible and streamlined management approach.

National Greenhouse Gas Emission Inventory (EV-GHG)

Data.gov (United States)

U.S. Environmental Protection Agency — The EV-GHG Mobile Source Data asset contains measured mobile source GHG emissions summary compliance information on light-duty vehicles, by model, for certification...

Evaluation of Fuel-Cell Range Extender Impact on Hybrid Electrical Vehicle Performance

DEFF Research Database (Denmark)

Jensen, Hans-Christian Becker; Schaltz, Erik; Koustrup, Per Sune

2013-01-01

The use of electric vehicles (EVs) is advantageous because of zero emission, but their market penetration is limited by one disadvantage, i.e., energy storage. Battery EVs (BEVs) have a limited range, and their batteries take a long time to charge, compared with the time it takes to refuel the tank...... of a vehicle with an internal combustion engine (ICE). Fuel cells (FCs) can be added to an EV as an additional energy source. These are faster to refill and will therefore facilitate the transition from vehicles running on fossil fuel to electricity. Different EV setups with FC strategies are presented...... in start/stop city cycles. Simulations with the New European Driving Cycle (NEDC) showed that efficiency fell by at least 15% for the FC hybrid EV (FCHEV) when compared with BEVs....

Environmental analysis of radiation exposure by radon in Saxon buildings and impact of the EnEV. An old problem in a new dimension; Umweltanalyse zur Strahlenbelastung durch Radon in saechsischen Gebaeuden und Auswirkungen der EnEV. Ein altes Problem mit neuen Dimensionen

Energy Technology Data Exchange (ETDEWEB)

Gottwald, Jan; Schneider, Lutz [Stoller Ingenieurtechnik GmbH, Dresden (Germany); Koeter, Nico [TU Bergakademie Freiberg (Germany)

2015-07-01

Radon in buildings is being widely studied since the 1990s. These studies have revealed some cases of very high radiation exposure for the inhabitants of residential buildings in Saxony in particular. Even a proposed raising of the radon reference values from 100 Bq/m{sup 3} to 300 Bq/m{sup 3} (in the case of an eventually 1:1 implementation of the EU recommendations into German law), would not even slightly aid the situation in the designated areas with high radon availability, as the standards of the Energieeinsparverordnung (Energy Saving Ordinance, EnEV) can result in significant radiation exposure, if no comprehensive radon protection is implemented. Based on long-term radon measurements in Saxony from the nineties, before the introduction of the EnEV, this report will show potential outcomes and estimate the extend of suitable remediation measures.

Avastamata aarete päev

Index Scriptorium Estoniae

2009-01-01

Ettevõtluse Arendamise Sihtasutus korraldas Pirita Lillepaviljonis Euroopa Komisjoni ning majandus- ja kommunikatsiooniministeeriumi toetusel 27. mail 2009 Avastamata aarete päeva. Päev oli pühendatud Eesti looduse väärtustamisele. Sõna võtsid EAS Turismiarenduskeskuse direktori asetäitja Marje Braunbrück, looduse- ja rännumees Hendrik Relve, Tallinna Ülikooli rekreatsiooniteaduste osakonna juhataja Mart Reimann ja reisikorraldaja Gerald Broddelez

Isolation and Characterization of Serum Extracellular Vesicles (EVs from Atlantic Salmon Infected with Piscirickettsia Salmonis

Directory of Open Access Journals (Sweden)

Leidy Lagos

2017-12-01

Full Text Available Secretion of extracellular vesicles (EVs is a common feature of both eukaryotic and prokaryotic cells. Isolated EVs have been shown to contain different types of molecules, including proteins and nucleic acids, and are reported to be key players in intercellular communication. Little is known, however, of EV secretion in fish, or the effect of infection on EV release and content. In the present study, EVs were isolated from the serum of healthy and Piscirickettsia salmonis infected Atlantic salmon in order to evaluate the effect of infection on EV secretion. P. salmonis is facultative intracellular bacterium that causes a systemic infection disease in farmed salmonids. EVs isolated from both infected and non-infected fish had an average diameter of 230–300 nm, as confirmed by transmission electron microscopy, nanoparticle tracking, and flow cytometry. Mass spectrometry identified 180 proteins in serum EVs from both groups of fish. Interestingly, 35 unique proteins were identified in serum EVs isolated from the fish infected with P. salmonis. These unique proteins included proteasomes subunits, granulins, and major histocompatibility class I and II. Our results suggest that EV release could be part of a mechanism in which host stimulatory molecules are released from infected cells to promote an immune response.

NASA's Earth Venture-1 (EV-1) Airborne Science Investigations

Science.gov (United States)

Guillory, A.; Denkins, T.; Allen, B. Danette; Braun, Scott A.; Crawford, James H.; Jensen, Eric J.; Miller, Charles E.; Moghaddam, Mahta; Maring, Hal

2011-01-01

In 2010, NASA announced the first Earth Venture (EV-1) selections in response to a recommendation made by the National Research Council for low-cost investigations fostering innovation in Earth science. The five EV-1 investigations span the Earth science focus areas of atmosphere, weather, climate, water and energy and, carbon and represent earth science researchers from NASA as well as other government agencies, academia and industry from around the world. The EV-1 missions are: 1) Airborne Microwave Observatory of Subcanopy and Subsurface (AirMOSS), 2) Airborne Tropical Tropopause Experiment (ATTREX), 3) Carbon in Arctic Reservoirs Vulnerability Experiment (CARVE), 4) Deriving Information on Surface Conditions from Column and Vertically Resolved Observations Relevant to Air Quality (DISCOVER-AQ), and 5) Hurricane And Severe Storm Sentinel (HS3). The Earth Venture missions are managed out of the Earth System Science Pathfinder (ESSP) Program Office (Allen, et. al. 2010b)

Fachagentur Nachwachsende Rohstoffe e.V. Annual report 2010/2011; Fachagentur Nachwachsende Rohstoffe e.V. (FNR). Jahresbericht 2010/2011

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

The annual report of the Fachagentur Nachwachsende Rohstoffe e.V. (Guelzow-Pruezen, Federal Republic of Germany) outlines the cultivation of industrial crops and energy plants. The organisational structure of the association and its research projects are presented.

Fachagentur Nachwachsende Rohstoffe e.V. Annual report 2009/2010; Fachagentur Nachwachsende Rohstoffe e.V. (FNR). Jahresbericht 2009/2010

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-07-01

The annual report of the Fachagentur Nachwachsende Rohstoffe e.V. (Guelzow-Pruezen, Federal Republic of Germany) outlines the cultivation of industrial crops and energy plants. The organisational structure of the association and its research projects are presented.

AP1000 - the new standard for nuclear power

International Nuclear Information System (INIS)

Lipman, Daniel S.

2006-01-01

/modularization The AP1000 is explicitly designed for modular construction. While modularization techniques can be applied to some extent to most designs, in order to realize maximum benefits the plant must be designed for modular construction from the very beginning. This approach offers significant benefits for sequencing and durations of construction activities. The AP1000 design incorporates structural modules, mechanical modules and piping modules. The benefits of modularization include reduced construction schedule, reduced field manpower, increased factory work, and reduced site construction. The AP1000 has a site construction duration of 36 months from first concrete to fuel loading. Reductions in equipment and bulk quantities allow AP1000's construction costs to be among the most competitive. Safety: As measured by the Probabilistic Safety Assessment, the AP1000 is designed to be more than 100 times safer than already safe operating nuclear plants--harnessing natural forces such as gravity, convection and condensation to maintain a passive safety system that kicks in automatically. This reduces the burden on the operator and greatly reduces the potential for human error. Other advantages to the passive safety system include: no reliance on AC power, an increase in containment reliability, and large margin to safety limits. (author)

Investigations in the upper load range of stratified operation with injection pressures up to 1000 bar; Untersuchungen im oberen Lastbereich des Schichtbetriebes bei Einspritzdruecken bis 1000 bar

Energy Technology Data Exchange (ETDEWEB)

Buri, Stefan; Busch, Steve; Kubach, Heiko; Spicher, Ulrich [Karlsruhe Univ. (DE). Inst. fuer Kolbenmaschinen (IFKM)

2010-07-01

This paper presents the results of recent research that has been performed on a single-cylinder spray-guided DISI engine at the Institut fuer Kolbenmaschinen. A production multihole injector is used as a baseline and compared with a specially adapted injector at higher injection pressures. Injection pressures of up to 1000 bar are utilized to investigate the combustion and emissions characteristics at the stability limit of stratified combustion. With the modified injector, measurements with the two-color method are applied to analyze this operating condition in terms of soot formation. Included are results for a spark timing variation with 1000 bar injection pressure, an injection pressure variation with constant spark timing, and fuel consumption-optimized engine operating parameters in order to analyze realistic operating points. The benefits of injecting fuel at higher pressures are described, as are the limitations of the experimental setup. (orig.)

Q values of the 76Ge and 100Mo double-beta decays

International Nuclear Information System (INIS)

Rahaman, S.; Elomaa, V.-V.; Eronen, T.; Hakala, J.; Jokinen, A.; Julin, J.; Kankainen, A.; Saastamoinen, A.; Suhonen, J.; Weber, C.; Aystoe, J.

2008-01-01

Penning trap measurements using mixed beams of 76 Ge- 76 Se and 100 Mo- 100 Ru have been utilized to determine the double-beta decay Q-values of 76 Ge and 100 Mo with uncertainties less than 200 eV. The value for 76 Ge, 2039.04(16) keV is in agreement with the published SMILETRAP value, 2039.006(50) keV. The new value for 100 Mo, 3034.40(17) keV is 30 times more precise than the previous literature value, sufficient for the ongoing neutrinoless double-beta decay searches in 100 Mo. Moreover, the precise Q-value is used to calculate the phase-space integrals and the experimental nuclear matrix element of double-beta decay

Analyzing public awareness and acceptance of alternative fuel vehicles in China: The case of EV

International Nuclear Information System (INIS)

Zhang Yong; Yu Yifeng; Zou Bai

2011-01-01

The aim of this paper is to analyze consumers' awareness towards electric vehicle (EV) and examine the factors that are most likely to affect consumers' choice for EV in China. A comprehensive questionnaire survey has been conducted with 299 respondents from various driving schools in Nanjing. Three binary logistic regression models were used to determine the factors that contribute to consumers' acceptance of EVs, their purchase time and their purchase price. The results suggest that: (1)Whether a consumer chooses an EV is significantly influenced by the number of driver's licenses, number of vehicles, government policies and fuel price. (2)The timing of consumers' purchases of an EV is influenced by academic degree, annual income, number of vehicles, government policies, the opinion of peers and tax incentives. (3)The acceptance of purchase price of EVs is influenced by age, academic degree, number of family members, number of vehicles, the opinion of peers, maintenance cost and degree of safety. These findings will help understand consumer's purchase behavior of EVs and have important policy implications related to the promotions of EVs in China. - Highlights: → We survey 299 respondents from various driving schools in Nanjing. → We analyze consumer's awareness towards electric vehicle (EV). → The factors affecting consumers' choice for EV are examined by three binary logistic models. → Factors contributing to consumers' acceptance of EVs, purchase time and purchase price are indicated.

1000 Norms Project: protocol of a cross-sectional study cataloging human variation.

Science.gov (United States)

McKay, Marnee J; Baldwin, Jennifer N; Ferreira, Paulo; Simic, Milena; Vanicek, Natalie; Hiller, Claire E; Nightingale, Elizabeth J; Moloney, Niamh A; Quinlan, Kate G; Pourkazemi, Fereshteh; Sman, Amy D; Nicholson, Leslie L; Mousavi, Seyed J; Rose, Kristy; Raymond, Jacqueline; Mackey, Martin G; Chard, Angus; Hübscher, Markus; Wegener, Caleb; Fong Yan, Alycia; Refshauge, Kathryn M; Burns, Joshua

2016-03-01

Clinical decision-making regarding diagnosis and management largely depends on comparison with healthy or 'normal' values. Physiotherapists and researchers therefore need access to robust patient-centred outcome measures and appropriate reference values. However there is a lack of high-quality reference data for many clinical measures. The aim of the 1000 Norms Project is to generate a freely accessible database of musculoskeletal and neurological reference values representative of the healthy population across the lifespan. In 2012 the 1000 Norms Project Consortium defined the concept of 'normal', established a sampling strategy and selected measures based on clinical significance, psychometric properties and the need for reference data. Musculoskeletal and neurological items tapping the constructs of dexterity, balance, ambulation, joint range of motion, strength and power, endurance and motor planning will be collected in this cross-sectional study. Standardised questionnaires will evaluate quality of life, physical activity, and musculoskeletal health. Saliva DNA will be analysed for the ACTN3 genotype ('gene for speed'). A volunteer cohort of 1000 participants aged 3 to 100 years will be recruited according to a set of self-reported health criteria. Descriptive statistics will be generated, creating tables of mean values and standard deviations stratified for age and gender. Quantile regression equations will be used to generate age charts and age-specific centile values. This project will be a powerful resource to assist physiotherapists and clinicians across all areas of healthcare to diagnose pathology, track disease progression and evaluate treatment response. This reference dataset will also contribute to the development of robust patient-centred clinical trial outcome measures. Copyright © 2015 Chartered Society of Physiotherapy. Published by Elsevier Ltd. All rights reserved.

Work function and quantum efficiency study of metal oxide thin films on Ag(100)

Science.gov (United States)

Chang, V.; Noakes, T. C. Q.; Harrison, N. M.

2018-04-01

Increasing the quantum efficiency (QE) of metal photocathodes is in the design and development of photocathodes for free-electron laser applications. The growth of metal oxide thin films on certain metal surfaces has previously been shown to reduce the work function (WF). Using a photoemission model B. Camino et al. [Comput. Mater. Sci. 122, 331 (2016), 10.1016/j.commatsci.2016.05.025] based on the three-step model combined with density functional theory calculations we predict that the growth of a finite number of MgO(100) or BaO(100) layers on the Ag(100) surface increases significantly the QE compared with the clean Ag(100) surface for a photon energy of 4.7 eV. Different mechanisms for affecting the QE are identified for the different metal oxide thin films. The addition of MgO(100) increases the QE due to the reduction of the WF and the direct excitation of electrons from the Ag surface to the MgO conduction band. For BaO(100) thin films, an additional mechanism is in operation as the oxide film also photoemits at this energy. We also note that a significant increase in the QE for photons with an energy of a few eV above the WF is achieved due to an increase in the inelastic mean-free path of the electrons.

EBSCO infopäev Tallinnas / Marika Meltsas

Index Scriptorium Estoniae

Meltsas, Marika

2008-01-01

16. aprillil 2008 toimus Tallinnas EBSCO (Elton B. Stephens Company) infopäev, kus maailma suurim elektrooniliste ja trükiajakirjade vahendaja tutvustas oma tooteid ja teenuseid Eesti raamatukogudele. Kommentaar korraldajalt Tiina Nurmilt

Policy strategies for an emergent technology: Lessons from the analysis of EV-policy in 8 North- European countries

NARCIS (Netherlands)

M. van der Steen (Martijn); R.M. Van Schelven; P. Van Deventer (Peter); M. van Twist (Mark); R. Kotter

2015-01-01

textabstractThis paper presents data from a comparative study of EV-policies in 8 different North-European countries, that maps out all of the policies of these countries (and a range of regions and cities) that target passenger vehicles (PHEV and BEV), chargers (home, private, public; level 1-3),

Analysis of the 235U neutron cross sections in the resolved resonance range

International Nuclear Information System (INIS)

Leal, L.C.; de Saussure, G.; Perez, R.B.

1989-01-01

Using recent high-resolution measurements of the neutron transmission of 235 U and the spin-separated fission cross-section data of Moore et al., a multilevel analysis of the 235 U neutron cross sections was performed up to 300 eV. The Dyson Metha Δ 3 statistics were used to help locate small levels above 100 eV where resonances are not clearly resolved even in the best resolution measurements available. The statistical properties of the resonance parameters are discussed

Study of hydrogen interaction with SiO2/Si(100) system using positrons

International Nuclear Information System (INIS)

Asoka-Kumar, P.; Lynn, K.G.; Leung, T.C.; Nielsen, B.; Wu, X.Y.

1991-01-01

We describe positron annihilation studies of SiO 2 /Si(100) structures having 100-nm-thick oxide grown by plasma enhanced chemical vapor deposition. A normalized shape parameter is used to characterize the positron annihilation spectra. Activation and passivation of interface states by atomic hydrogen are demonstrated by repeated vacuum anneal and atomic hydrogen exposure. Hydrogen activation energy is derived for one of the samples as 2.02±0.07 eV

In-situ oxidation study of Pd(100) by surface x-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Kilic, Volkan; Franz, Dirk; Stierle, Andreas [AG Grenzflaechen, Universitaet Siegen (Germany); Martin, Natalia; Lundgren, Edvin [Department of Synchrotron Radiation Research, Lund University (Sweden); Mantilla, Miguel [MPI fuer Metallforschung, Stuttgart (Germany)

2011-07-01

The oxidation of the Pd(100) surface at oxygen pressures in the 10{sup -6} mbar to 10{sup 3} mbar range and temperatures up to 1000 K has been studied in-situ by surface x-ray diffraction (SXRD). The SXRD experiments were performed at the MPI beamline at the Angstrom Quelle Karlsruhe (ANKA). We present the surface and crystal truncation rod (CTR) data from the ({radical}(5) x {radical}(5)) surface layer. We show that the transformation from the surface oxide to PdO bulk oxide can be observed in-situ under specific pressure and temperature conditions. We compare our results with previously proposed structure models based on low energy electron diffraction (LEED) I(V) curves and density functional theory calculations. Finally, we elucidate the question of commensurability of the surface oxide layer with respect to the Pd(100) substrate.

Design of narrow band photonic filter with compact MEMS for tunable resonant wavelength ranging 100 nm

Directory of Open Access Journals (Sweden)

Guanquan Liang

2011-12-01

Full Text Available A prototype of planar silicon photonic structure is designed and simulated to provide narrow resonant line-width (∼2 nm in a wide photonic band gap (∼210 nm with broad tunable resonant wavelength range (∼100 nm around the optical communication wavelength 1550 nm. This prototype is based on the combination of two modified basic photonic structures, i.e. a split tapered photonic crystal micro-cavity embedded in a photonic wire waveguide, and a slot waveguide with narrowed slabs. This prototype is then further integrated with a MEMS (microelectromechanical systems based electrostatic comb actuator to achieve “coarse tune” and “fine tune” at the same time for wide range and narrow-band filtering and modulating. It also provides a wide range tunability to achieve the designed resonance even fabrication imperfection occurs.

AP1000 Design for Security

International Nuclear Information System (INIS)

Long, L.B.; Cummins, W.E.; Winters, J.W.

2006-01-01

Nuclear power plants are protected from potential security threats through a combination of robust structures around the primary system and other vital equipment, security systems and equipment, and defensive strategy. The overall objective for nuclear power plant security is to protect public health and safety by ensuring that attacks or sabotage do not challenge the ability to safely shutdown the plant or protect from radiological releases. In addition, plants have systems, features and operational strategies to cope with external conditions, such as loss of offsite power, which could be created as part of an attack. Westinghouse considered potential security threats during design of the AP1000 PWR. The differences in plant configuration, safety system design, and safe shutdown equipment between existing plants and AP1000 affect potential vulnerabilities. This paper provides an evaluation of AP1000 with respect to vulnerabilities to security threats. The AP1000 design differs from the design of operating PWRs in the US in the configuration and the functional requirements for safety systems. These differences are intentional departures from conventional PWR designs which simplify plant design and enhance overall safety. The differences between the AP1000 PWR and conventional PWRs can impact vulnerabilities to security threats. The NRC addressed security concerns as part of their reviews for AP1000 Design Certification, and did not identify any security issues of concern. However, much of the detailed security design information for the AP1000 was deferred to the combined Construction and Operating License (COL) phase as many of the security issues are site-specific. Therefore, NRC review of security issues related to the AP1000 is not necessarily complete. Further, since the AP1000 plant design differs from existing PWRs, it is not obvious that the analyses and assessments prepared for existing plants also apply to the AP1000. We conclude that, overall, the AP1000

Palladium diffusion into bulk copper via the (100) surface

Energy Technology Data Exchange (ETDEWEB)

Bussmann, E; Kellogg, G L [Sandia National Laboratories, Albuquerque, NM 87185 (United States); Sun, J; Pohl, K [Department of Physics and Materials Science Program, University of New Hampshire, Durham, NH 03824 (United States)

2009-08-05

Using low-energy electron microscopy, we measure the diffusion of Pd into bulk Cu at the Cu(100) surface. Interdiffusion is tracked by measuring the dissolution of the Cu(100)-c(2 x 2)-Pd surface alloy during annealing (T>240 deg. C). The activation barrier for Pd diffusion from the surface alloy into the bulk is determined to be (1.8 +- 0.6) eV. During annealing, we observe the growth of a new layer of Cu near step edges. Under this new Cu layer, dilute Pd remaining near the surface develops a layered structure similar to the Cu{sub 3}Pd L 1{sub 2} bulk alloy phase.

Nitrogen adsorption on Fe(111), (100), and (110) surfaces

DEFF Research Database (Denmark)

Mortensen, Jens Jørgen; Ganduglia-Pirovano, Veronica; Hansen, Lars Bruno

1999-01-01

Adsorption energies and structures for N atoms on three low-index surfaces of Fe have been calculated using density functional theory (DFT) and the generalized gradient approximation (GGA). At low N coverage the adsorption energy on Fe(100) is found to be similar to 0.7 eV higher than on the (111......) and (110) surfaces - particularly the c(2 x 2)-N/Fe(100) structure with the N atoms in four-fold sites is very stable. We attribute the differences in adsorption energy to the lack of four-fold sites on the (111) and (110) surfaces, We suggest that at higher N coverages, islands with a structure similar...

Secondary electron energy distributions for gold as excited by C-K/sub α/ (277 eV) and A1-K/sub α/ (1487 eV) x-rays. Final report, 15 April 1976--14 November 1976

International Nuclear Information System (INIS)

Henke, B.L.; Smith, J.A.

1976-01-01

The secondary electron energy distributions for a gold photocathode as excited by C-K/sub α/ (277 eV) and Al-K/sub α/ (1487 eV) x-rays were measured. The shape of the energy distributions are essentially the same for these two x-ray photon excitation energies. For thick, evaporated gold samples on glass substrates (at 150 0 C and 3 x 10 -8 torr), the secondary electron energy distributions peak at about one eV and have a FWHM of about four eV. As measured immediately after ion-cleaning, the distributions peak at about two eV and have a FWHM of about 6.6 eV. Approximately five hours after ion-cleaning, the measured distributions appear as those obtained before ion-cleaning. The work function of the evaporated gold photocathode temporarily increases by one eV upon ion-cleaning

Fachagentur Nachwachsende Rohstoffe e.V. Annual report 2011/2012; Fachagentur Nachwachsende Rohstoffe e.V. (FNR). Jahresbericht 2011/2012

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

The annual report of the Fachagentur Nachwachsende Rohstoffe e.V. (Guelzow-Pruezen, Federal Republic of Germany) outlines the cultivation of industrial crops and energy plants in Germany. The organisational structure of the association and its research projects are presented for the fiscal year 2011/2012.

Performance of flash ADCs in the 100 MHz range: I. Test bench and preliminary results

International Nuclear Information System (INIS)

Crawley, H.B.; McKay, R.; Meyer, W.T.; Rosenberg, E.I.; Thomas, W.D.

1990-01-01

We describe a systematic study of the performance of commercially available Flash ADCs in the 100 Megasample per second range, which might be suitable for use in the Superconducting Super Collider. Performance characteristics are measured using a CAMAC based test bench which is described. Among the FADC performance characteristics reported are linearity, differential linearity and the effective number of bits. This paper is the first in a series of reports to be presented within the next year as our tests continue. 6 refs., 2 figs., 1 tab

Ettelugemisepäev on tulekul / Krista Kumberg

Index Scriptorium Estoniae

Kumberg, Krista, 1959-

2004-01-01

Ettelugemispäevast, mil propageeritakse raamatute ettelugemist. Sisaldab ka muinasjuttu "Elasid kord eit ja taat..." ainsalt kutseliselt jutuvestjalt Eestis, Piret Päärilt. Vaata ka "Virumaa Teataja" 19. 10., lk. 4 pealkirjaga "Homne ettelugemispäev veedetakse koos raamatutega"

Analysis of the 235U neutron cross sections in the resolved resonance range

International Nuclear Information System (INIS)

Leal, L.C.; de Saussure, G.; Perez, R.B.

1989-01-01

Using recent high-resolution measurements of the neutron transmission of 235 U and the spin-separated fission cross-section data of Moore et al., a multilevel analysis of the 235 U neutron cross sections was performed up to 300 eV. The Dyson Metha Δ 3 statistics were used to help locate small levels above 100 eV where resonances are not clearly resolved even in the best resolution measurements available. The statistical properties of the resonance parameters are discussed. 13 refs., 8 figs., 1 tab

Air oxidation of Zircaloy-4 in the 600-1000 °C temperature range: Modeling for ASTEC code application

Science.gov (United States)

Coindreau, O.; Duriez, C.; Ederli, S.

2010-10-01

Progress in the treatment of air oxidation of zirconium in severe accident (SA) codes are required for a reliable analysis of severe accidents involving air ingress. Air oxidation of zirconium can actually lead to accelerated core degradation and increased fission product release, especially for the highly-radiotoxic ruthenium. This paper presents a model to simulate air oxidation kinetics of Zircaloy-4 in the 600-1000 °C temperature range. It is based on available experimental data, including separate-effect experiments performed at IRSN and at Forschungszentrum Karlsruhe. The kinetic transition, named "breakaway", from a diffusion-controlled regime to an accelerated oxidation is taken into account in the modeling via a critical mass gain parameter. The progressive propagation of the locally initiated breakaway is modeled by a linear increase in oxidation rate with time. Finally, when breakaway propagation is completed, the oxidation rate stabilizes and the kinetics is modeled by a linear law. This new modeling is integrated in the severe accident code ASTEC, jointly developed by IRSN and GRS. Model predictions and experimental data from thermogravimetric results show good agreement for different air flow rates and for slow temperature transient conditions.

Westinghouse AP1000 licensing maturity

International Nuclear Information System (INIS)

Schulz, T.; Vijuk, R.P.

2005-01-01

The Westinghouse AP1000 Program is aimed at making available a nuclear power plant that is economical in the U.S deregulated electrical power industry in the near-term. The AP1000 is two-loop 1000 MWe pressurizer water reactor (PWR). It is an up rated version of the AP600. The AP1000 uses passive safety systems to provide significant and measurable improvements in plant simplification, safety, reliability, investment protection and plant costs. The AP1000 uses proven technology, which builds on over 35 years of operating PWR experience. The AP1000 received Final Design Approval by the United States Nuclear Regulatory Commission (U.S. NRC) in September 2004. The AP1000 meets the US utility requirements. The AP1000 and its sister plant the AP600 have gone through a very through and complete licensing review. This paper describes the U.S. NRC review efforts of both the AP600 and the AP1000. The detail of the review and the independent calculations, evaluations and testing is discussed. The AP600 licensing documentation was submitted in 1992. The U.S. NRC granted Final Design Approval in 1999. During the intervening 7 years, the U.S. NRC asked thousands of questions, performed independent safety analysis, audited Westinghouse calculations and analysis, and performed independent testing. The more significant areas of discussion will be described. For the AP1000 Westinghouse first engaged the U.S. NRC in pre-certification discussions to define the extent of the review required, since the design is so similar to the AP600. The AP1000 licensing documentation was submitted in March 2002. The U.S. NRC granted Final Design Approval in September 2004. During the intervening 2 1/2 years, the U.S. NRC asked hundreds of questions, performed independent safety analysis, audited Westinghouse calculations and analysis, and performed independent testing. The more significant areas of discussion will be described. The implications of this review and approval on AP1000 applications in

Binding free energy analysis of protein-protein docking model structures by evERdock.

Science.gov (United States)

Takemura, Kazuhiro; Matubayasi, Nobuyuki; Kitao, Akio

2018-03-14

To aid the evaluation of protein-protein complex model structures generated by protein docking prediction (decoys), we previously developed a method to calculate the binding free energies for complexes. The method combines a short (2 ns) all-atom molecular dynamics simulation with explicit solvent and solution theory in the energy representation (ER). We showed that this method successfully selected structures similar to the native complex structure (near-native decoys) as the lowest binding free energy structures. In our current work, we applied this method (evERdock) to 100 or 300 model structures of four protein-protein complexes. The crystal structures and the near-native decoys showed the lowest binding free energy of all the examined structures, indicating that evERdock can successfully evaluate decoys. Several decoys that show low interface root-mean-square distance but relatively high binding free energy were also identified. Analysis of the fraction of native contacts, hydrogen bonds, and salt bridges at the protein-protein interface indicated that these decoys were insufficiently optimized at the interface. After optimizing the interactions around the interface by including interfacial water molecules, the binding free energies of these decoys were improved. We also investigated the effect of solute entropy on binding free energy and found that consideration of the entropy term does not necessarily improve the evaluations of decoys using the normal model analysis for entropy calculation.

The evolution of Vp1 gene in enterovirus C species sub-group that contains types CVA-21, CVA-24, EV-C95, EV-C96 and EV-C99.

Directory of Open Access Journals (Sweden)

Teemu Smura

Full Text Available Genus Enterovirus (Family Picornaviridae, consists of twelve species divided into genetically diverse types by their capsid protein VP1 coding sequences. Each enterovirus type can further be divided into intra-typic sub-clusters (genotypes. The aim of this study was to elucidate what leads to the emergence of novel enterovirus clades (types and genotypes. An evolutionary analysis was conducted for a sub-group of Enterovirus C species that contains types Coxsackievirus A21 (CVA-21, CVA-24, Enterovirus C95 (EV-C95, EV-C96 and EV-C99. VP1 gene datasets were collected and analysed to infer the phylogeny, rate of evolution, nucleotide and amino acid substitution patterns and signs of selection. In VP1 coding gene, high intra-typic sequence diversities and robust grouping into distinct genotypes within each type were detected. Within each type the majority of nucleotide substitutions were synonymous and the non-synonymous substitutions tended to cluster in distinct highly polymorphic sites. Signs of positive selection were detected in some of these highly polymorphic sites, while strong negative selection was indicated in most of the codons. Despite robust clustering to intra-typic genotypes, only few genotype-specific 'signature' amino acids were detected. In contrast, when different enterovirus types were compared, there was a clear tendency towards fixation of type-specific 'signature' amino acids. The results suggest that permanent fixation of type-specific amino acids is a hallmark associated with evolution of different enterovirus types, whereas neutral evolution and/or (frequency-dependent positive selection in few highly polymorphic amino acid sites are the dominant forms of evolution when strains within an enterovirus type are compared.

Theoretical photoionization spectra in the UV photon energy range for a Mg-like Al+ ion

International Nuclear Information System (INIS)

Kim, Dae-Soung; Kim, Young Soon

2008-01-01

In the present work, we report the photoionization cross sections of the Al + ion calculated for the photon energy range 20-26 eV and 30-50 eV. We have expanded our previous calculation (2007 J. Phys. Soc. Japan 76 014302) with an optimized admixture of the initial ground state 3s 21 S and exited states 3s3p 1,3 P, 3s3d 1,3 D and 3s4s 1,3 S, and obtained significantly improved predictions for the main background and autoionizing resonance structures of the reported experimental spectra. The absolute measurements of the photoionization cross sections of the Al + ion in these energy ranges have been performed by West et al (2001 Phys. Rev. A 63 052719), and they reported that the prominent peaks around 21 eV were attributed to the effects of the significant influence of the small fraction of the fourth-order radiation with energies around 84 eV from the synchrotron source. In our previous work, the main shape for these cross sections was calculated assuming an admixture of initial 3s 21 S and 3s3p 3 P states, only with a rough overall estimate for the experimental spectra in the photon energy range 20-26 eV, and without these peaks around 21 eV. The report of the experimental assignment attributes these peaks to the excitation of a 2p electron from the core. However, our present results with the new admixture reveal similar peaks without considering the possibility of the core excitation

Synthesis and properties of layered synthetic microstructure (LSM) dispersion elements for 62 eV (200A) to 1.24 keV (10A) radiation. Final report

International Nuclear Information System (INIS)

Barbee, T.W. Jr.

1981-08-01

The opportunities offered by engineered synthetic multilayer dispersion elements for x-rays have been recognized since the earliest days of x-ray diffraction analysis. In this paper, application of sputter deposition technology to the synthesis of Layered Synthetic Microstructure (LSMs) of sufficient quality for use as x-ray dispersion elements is discussed. It will be shown that high efficiency, controllable bandwidth dispersion elements, with d spacings varying from 15 A to 180 A, may be synthesized onto both mechanically stiff and flexible substrates. Multilayer component materials include tungsten, niobium, molybdenum, titanium, vanadium, and silicon layers separated by carbon layers. Experimental observations of peak reflectivity in first order, integrated reflectivity in first order, and diffraction performance at selected photon energies in the range, 100 to 15,000 eV, are reported and compared to theory

Strategic Concept of the Development of EV and SFV in China

Institute of Scientific and Technical Information of China (English)

1997-01-01

<正> Ⅰ. Strategic Concept for the development of EV and SFV The development of EV and SFV is one of the objective requirements for the auto industry in the 21st century by sustainable development strategy. It is also a practicable way of developing China auto industry in line with the environmental protection policy and the energy develop

A Game Theoretic Approach for EV Recharge Pricing Under Competition: Analysis and Simulation

OpenAIRE

Amigo , Isabel; Gagnaire , Maurice

2015-01-01

Electric Vehicles (EV) are a key element of future smart cities, providing a clean transportation technology and potential benefits for the grid. Nevertheless, limited vehicle autonomy and lack of charging stations are preventing EVs to be broadly accepted. To address this challenge, French GreenFeed project is working to develop an interoperable and universal architecture to allow EV recharge across multiple cities and countries. In this work, we consider such architecture and focus on price...

Photoelectron spectrometry of manganese vapor between 12 and 110 eV

International Nuclear Information System (INIS)

Krause, M.O.; Carlson, T.A.; Fahlman, A.

1984-01-01

The important dynamic parameters, partial photoionization cross section sigma and angular distribution parameter β, have been determined for atomic Mn between 12 and 110 eV by electron spectroscopy with synchrotron radiation (ESSR). The single-electron photolines from the 3d and 4s subshells and the associated two-electron satellite lines were measured, and the resonance region of 3p→3d excitation around 50 eV was studied in detail. Absolute partial cross sections were derived. For the 3d-subshell properties, we find good agreement with the many-body perturbation-theory calculation (MBPT) by Garvin et al. over the entire energy range and with the random-phase-approximation results by Amusia et al. over the 3p resonance region. Available calculation (MBPT) underestimates the enhancement of sigma(4s) through the 3p resonance. Where overlap exists, the experimental data by Bruhn et al. and by Kobrin et al. agree well with our results. The work on Mn, taken in toto, provides a good overall understanding of the photoionization dynamics of the 3d transition series element Mn, which has a half-filled subshell, although a number of problems, e.g., two- and three-electron transitions and the low-energy region, remain to be further studied. A need for an accurate determination (5--10%) of the total photoabsorption cross section is indicated

First isolation of enterovirus 71 (EV-71 from Northern Brazil

Directory of Open Access Journals (Sweden)

Lamarão Leticia Martins

2003-01-01

Full Text Available Enterovirus 71 (EV-71 has been associated to cases of neurological disease in many countries including Brazil. This virus has now been reported from three of the five Brazilian regions. Our study relates the findings concerning to the first isolate of this virus in Northern region of Brazil. A 15-month old female patient, from the rural zone of the municipality of Santana do Araguaia in southern Pará state was admitted at the hospital with acute, flaccid, asymmetric and ascending motor deficiency, located in the right lower limb. Stools samples from this child were inoculated in RD cells and was isolated an EV-71. We plan to sequence our strain and compare it to other isolates in Brazil. Differences at the molecular level can explain why EV-71 strains circulating in other continents, such as Asia, appear to be more virulent.

The passive safety systems of the Swr 1000

International Nuclear Information System (INIS)

Neumann, D.

2001-01-01

In recent years, a new boiling water reactor (BWR) plant called the SWR 1000 has been developed by Siemens on behalf of Germany's electric utilities. This new plant design concept incorporates the wide range of operating experience gained with German BWRs. The main objective behind developing the SWR 1000 was to design a plant with a rated electric output of approximately 1000 MW which would not only have a lower capital cost and lower power generating costs but would also provide a much higher level of nuclear safety compared to plants currently in operation. This safety-related goal has been met through, for example, the use of passive safety equipment. Passive systems make a significant contribution towards increasing the over-all level of plant safety due to the way in which they operate. They function solely accord-ing to basic laws of nature, such as gravity, and perform their designated functions with-out any need for electric power or other sources of external energy, or signals from instrumentation and control (I and C) equipment. The passive safety systems have been designed such that design basis accidents can be controlled using just these systems alone. However, the design concept of the SWR 1000 is nevertheless still based on the provision of active safety systems in addition to passive systems. (author)

Fixed energy inversion of 5 eV e-Xe atom scattering

International Nuclear Information System (INIS)

Lovell, A.; Amos, K.

2000-01-01

Fixed energy inverse scattering theory has been used to define central and spin-orbit Schroedinger potentials for the scattering of 5 eV polarized electrons from Xe atoms. The results are typical for a range of such data; including energies above threshold when the potentials become complex. The phase shifts obtained from an analysis of the measured differential cross section and analyzing power has been used as input data. Both semi-classical (WKB) and fully quantal inversion methods have been used to extract central and spin-orbit interactions. The analysis shows that information additional to the set of input phase shifts extracted from this (and similar) data may be needed to ascertain physical potentials

EV71 vaccine, a new tool to control outbreaks of hand, foot and mouth disease (HFMD).

Science.gov (United States)

Mao, Qun-ying; Wang, Yiping; Bian, Lianlian; Xu, Miao; Liang, Zhenglun

2016-05-01

On December 3rd 2015, the China Food and Drug Administration (CFDA) approved the first inactivated Enterovirus 71 (EV71) whole virus vaccine for preventing severe hand, foot and mouth disease (HFMD). As one of the few preventive vaccines for children's infectious diseases generated by the developing countries in recent years, EV71 vaccine is a blessing to children's health in China and worldwide. However, there are still a few challenges facing the worldwide use of EV71 vaccine, including the applicability against various EV71 pandemic strains in other countries, international requirements on vaccine production and quality control, standardization and harmonization on different pathogen monitoring and detecting methods, etc. In addition, the affordability of EV71 vaccine in other countries is a factor to be considered in HFMD prevention. Therefore, with EV71 vaccine commercially available, there is still a long way to go before reaching effective protection against severe HFMD after EV71 vaccines enter the market. In this paper, the bottlenecks and prospects for the wide use of EV71 vaccine after its approval are evaluated.

47 CFR 76.1000 - Definitions.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Definitions. 76.1000 Section 76.1000 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE Competitive Access to Cable Programming § 76.1000 Definitions. As used in this...

7 CFR 3017.1000 - Respondent.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Respondent. 3017.1000 Section 3017.1000 Agriculture Regulations of the Department of Agriculture (Continued) OFFICE OF THE CHIEF FINANCIAL OFFICER, DEPARTMENT OF AGRICULTURE GOVERNMENTWIDE DEBARMENT AND SUSPENSION (NONPROCUREMENT) Definitions § 3017.1000 Respondent...

40 CFR 725.1000 - Scope.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Scope. 725.1000 Section 725.1000 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT REPORTING....1000 Scope. This subpart identifies uses of microorganisms which EPA has determined to be significant...

40 CFR 51.1000 - Definitions.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 2 2010-07-01 2010-07-01 false Definitions. 51.1000 Section 51.1000 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS REQUIREMENTS FOR... Ambient Air Quality Standards § 51.1000 Definitions. The following definitions apply for purposes of this...

7 CFR 760.1000 - Applicability.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Applicability. 760.1000 Section 760.1000 Agriculture Regulations of the Department of Agriculture (Continued) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE... Catfish Grant Programs § 760.1000 Applicability. (a) This subpart establishes the terms and conditions...

Investigation of the composition-structure-property relationship of AsxTe100 - x films prepared by plasma deposition

Science.gov (United States)

Mochalov, Leonid; Dorosz, Dominik; Nezhdanov, Aleksey; Kudryashov, Mikhail; Zelentsov, Sergey; Usanov, Dmitry; Logunov, Alexandr; Mashin, Aleksandr; Gogova, Daniela

2018-02-01

AsxTe100 - x amorphous films of different chemical content were prepared by Plasma-Enhanced Chemical Vapor Deposition (PECVD). For the first time the optical properties of As-Te chalcogenide materials have been measured in UV-VIS-IR ranges (from 0.2 to 25 μm) for a very wide range of chemical compositions (20-80 at.% As). As-Te films have been tuned from 0.80 to 1.10 eV. The IR results obtained have been juxtaposed with the Raman spectroscopy findings to establish the correlation between optical and structural properties of the materials developed. Reversible and irreversible changes in the phase composition of the As-Te films under annealing of the surface by laser irradiation have been demonstrated and studied. In order to determine the potential areas of application of the prepared As-Te films the thermal and photo sensitivity has been also investigated.

Developing Online Marketing in Social Media for DORTMUNDtourismus e.V.

OpenAIRE

Steinrücken, Thomas

2010-01-01

The thesis discussed the topic of online marketing in social media. The focus was set on the social media platforms Facebook, YouTube and Flickr. Commissioner of the thesis was DORTMUNDtourismus e.V., the destination management organization for Dortmund, Germany. The research problem was to identify ways to develop online marketing in social media in a cost-efficient and innovative way in order to raise the awareness of DORTMUNDtourismus e.V. and Dortmund in social media and as a destination....

46 CFR 154.1000 - Applicability.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Applicability. 154.1000 Section 154.1000 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR... § 154.1000 Applicability. Sections 154.1005 through 154.1020 apply to flammable cargo and ammonia...

Electron-helium scattering in Debye plasmas

International Nuclear Information System (INIS)

Zammit, Mark C.; Fursa, Dmitry V.; Bray, Igor; Janev, R. K.

2011-01-01

Electron-helium scattering in weakly coupled hot-dense (Debye) plasma has been investigated using the convergent close-coupling method. The Yukawa-type Debye-Hueckel potential has been used to describe plasma Coulomb screening effects. Benchmark results are presented for momentum transfer cross sections, excitation, ionization, and total cross sections for scattering from the ground and metastable states of helium. Calculations cover the entire energy range up to 1000 eV for the no screening case and various Debye lengths (5-100 a 0 ). We find that as the screening interaction increases, the excitation and total cross sections decrease, while the total ionization cross sections increase.

A Stochastic Bi-Level Scheduling Approach for the Participation of EV Aggregators in Competitive Electricity Markets

DEFF Research Database (Denmark)

Rashidizaheh-Kermani, Homa; Vahedipour-Dahraie, Mostafa; Najafi, Hamid Reza

2017-01-01

are modeled via stochastic programming. Therefore, a two-level problem is formulated here, in which the aggregator makes decision in the upper level and the EV clients purchase energy to charge their EVs in the lower level. Then the obtained nonlinear bi-level framework is transformed into a single......This paper proposes a stochastic bi-level decision-making model for an electric vehicle (EV) aggregator in a competitive environment. In this approach, the EV aggregator decides to participate in day-ahead (DA) and balancing markets and provides energy price offers to the EV owners in order...... is assessed in a realistic case study and the results show that the proposed model would be effective for an EV aggregator decision-making problem in a competitive environment....

Eaton launches EV certification for fast-growing electric vehicle market

Energy Technology Data Exchange (ETDEWEB)

Anon

2011-11-15

This paper presents Electrical Line magazine's industry news, where it covers the launch by Eaton Corporation of electric vehicle (EV) certification for the fast-growing electric vehicle market. The aim of the certification is to help homeowners locate electricians specializing in electric vehicle support. Eaton certified EV contractors will visit the residence of people interested in an EV and determine if it can support a charging station. These contractors are trained, qualified and members of Eaton's certified contractor network. The residential power stations come in a wall-mount or pedestal model that can fully charge an electric car in 6 to 24 hours, depending on the model. The article also covers a new venture by Powercheck, a Vancouver-based company, which ensures that electrical wiring in older homes is safe and complies with their insurance company's safety requirements. Powercheck examines the entire house for electrical fire hazards and produces a detailed report listing the corrective actions needed.

29 CFR 98.1000 - Respondent.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Respondent. 98.1000 Section 98.1000 Labor Office of the Secretary of Labor GOVERNMENTWIDE DEBARMENT AND SUSPENSION (NONPROCUREMENT) Definitions § 98.1000 Respondent. Respondent means a person against whom an agency has initiated a debarment or suspension action. ...

33 CFR 151.1000 - Purpose.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Purpose. 151.1000 Section 151.1000 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) POLLUTION... Transportation of Municipal and Commercial Waste § 151.1000 Purpose. The purpose of this subpart is to implement...

Accuracy of Topcon CM-1000 videokeratoscope on spherical test surfaces.

Science.gov (United States)

Pérez-Yern, E; Fimia-Gil, A; Mateos, F; Carretero, L

1997-01-01

Many videokeratoscopes use mathematical formulas to calculate corneal radii; calculations depend on slope, curvature, coordinate position, or focal properties of the surface. Accuracy of each type of videokeratoscope must be evaluated. A controversy exists about whether axial or tangential methods best provide a precise description of corneal shape; therefore results with the Topcon CM-1000 using both methods were evaluated. Measurements were done on black polymethylmethacrylate (PMMA) spherical calibrated surfaces. Lenses were first aligned and measured and then misaligned in different directions and measured. Results for each position were compared with the zero or alignment position. Accuracy of the CM-1000 was high even under extreme misalignment conditions. Tolerance to misalignment was high (about 300 mm). Misalignment-induced variations in the output results were small (usually less than 0.05 mm). However, important variations (more than 1.00 diopter [D]) were found for the lowest measured radius (6 mm). In some cases, small differences between axial and tangential radii for the same point could be found. With the exception of extremely low radii of curvature, the CM-1000 was accurate for measuring spherical surfaces. Further investigation remains to be done on aspheric surfaces and in clinical practice.

Feasibility Study on Dual-Cooled Annular Fuel for OPR-1000 Power Uprate

International Nuclear Information System (INIS)

Chun, Tae Hyun; In, Wang Kee; Oh, Dong Suck

2010-04-01

A dual-cooled annular fuel (DCAF) is a highly promising concept as a high power density fuel for PWR power-uprate. The purpose of this study is to assess a feasibility of 120% core power for OPR-1000 with the DCAF. So the feasibility study were done through the code establishments for annular fuel analysis, evaluations of core physics, thermal-hydraulics and safety analyses at a 120% power with OPR-1000 and the preliminary economic benefits of 20% power-uprate. As results of the analyses, DCAF at 120% power showed sufficient margins available on DNB, PCT and fuel pellet temperature relative to the solid fuel at 100% power. However, judging from an anticipated wide range of the gap conductance variation in inner and outer clearances as fuel burn-up in the reactor core, irradiation behavior of DCAF has to be observed through research reactor test. On the other hand, the nuclear physics parameters like moderator temperature coefficient, power coefficient and so on comply with the technical specifications. An impact of 20% power-uprate on NSSS and BOP was also investigated, and accordingly some components and parts need to be changed were identified. Moreover, the economical benefits from the power-uprate was roughly estimated. It turned out that the power-uprating with DCAF could give an enormous profit even considering the expenses of components and parts to be replaced, additional fuel cycle cost and extended overhaul period

Summary Report on the SAE 2016 Range Extenders for Electric Vehicles Symposium

Energy Technology Data Exchange (ETDEWEB)

Curran, Scott [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wagner, Robert M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Campbell, Russ [SRA International, Inc., Arlington, VA (United States)

2017-03-01

The SAE 2016 Range Extenders for Electric Vehicles Symposium was a 2-day technical meeting focused on the role of advanced internal combustion engines (ICEs) and other novel energy converter technologies for extending the range of electric vehicles (EVs). The first-of-its-kind symposium was notable for focusing solely on the range extender (REx) technologies and not the EVs. The technical program featured presentations from international leaders from industry, government, national laboratories, and academia. The opening keynote presentations covered a broad range of topics including consumer behavior, policy implications, regulatory considerations, and REx architectures as enablers for advanced technologies. The technical sessions focused on an array of REx technologies including conventional ICEs, as well as less conventional or emerging technologies such as microturbines, fuel cells, low-temperature combustion engines, and aluminum-air batteries. The symposium included two panel sessions. The trend toward increasing vehicle electrification and the changing role of ICEs and other auxiliary power unit technologies for use as REx’s is leading to new research and design development needs. The symposium captured the interest of the industry and research communities in exploring the opportunities and challenges associated with REx’s for EVs. This report includes key takeaways, summarized below, and draft notes for each presentation and panel discussion.

21 CFR 1000.1 - General.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false General. 1000.1 Section 1000.1 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) RADIOLOGICAL HEALTH GENERAL General Provisions § 1000.1 General. References in this subchapter J to regulatory sections of the...

Information Spreadsheet for Engines and Vehicles Compliance Information System (EV-CIS) User Registration

Science.gov (United States)

In this spreadsheet, user(s) provide their company’s manufacturer code, user contact information for EV-CIS, and user roles. This spreadsheet is used for the Company Authorizing Official (CAO), CROMERR Signer, and EV-CIS Submitters.

Large Scale Deployment of Electric Vehicles (EVs) and Heat Pumps (HPs) in the Nordic Region

DEFF Research Database (Denmark)

Liu, Zhaoxi; Wu, Qiuwei; Petersen, Pauli Fríðheim

This report describes the study results of large scale deployment of electric vehicles (EVs) and heat pumps (HPs) in the Nordic countries of Denmark, Norway, Sweden and Finland, focusing on the demand profiles with high peneration of EVs and HPs in 2050......This report describes the study results of large scale deployment of electric vehicles (EVs) and heat pumps (HPs) in the Nordic countries of Denmark, Norway, Sweden and Finland, focusing on the demand profiles with high peneration of EVs and HPs in 2050...

ASD-1000: High-resolution, high-temperature acetylene spectroscopic databank

Science.gov (United States)

Lyulin, O. M.; Perevalov, V. I.

2017-11-01

We present a high-resolution, high-temperature version of the Acetylene Spectroscopic Databank called ASD-1000. The databank contains the line parameters (position, intensity, Einstein coefficient for spontaneous emission, term value of the lower states, self- and air-broadening coefficients, temperature dependence exponents of the self- and air-broadening coefficients) of the principal isotopologue of C2H2. The reference temperature for line intensity is 296 K and the intensity cutoff is 10-27 cm-1/(molecule cm-2) at 1000 K. The databank has 33,890,981 entries and covers the 3-10,000 cm-1 spectral range. The databank is based on the global modeling of the line positions and intensities performed within the framework of the method of effective operators. The parameters of the effective Hamiltonian and the effective dipole moment operator have been fitted to the observed values of the line positions and intensities collected from the literature. The broadening coefficients as well as their temperature dependence exponents were calculated using the empirical equations. The databank is useful for studying high-temperature radiative properties of C2H2. ASD-1000 is freely accessible via the Internet site of V.E. Zuev Institute of Atmospheric Optics SB RAS ftp://ftp.iao.ru/pub/ASD1000/.

Uudised : Eesti Filharmoonia Kammerkoor Iisraelis. RAM esineb USAs. Suur koorikontsert Kuno Arengu auks. Riho Pätsi mälestuspäev / Leelo Kõlar

Index Scriptorium Estoniae

Kõlar, Leelo, 1927-

1999-01-01

EFK T. Kaljuste juhatusel annab 28.09-3.10 Abu-Goshi muusikafestivalil Iisraelis kuus kontserti. RAM alustas kahekümnepäevast USA-turneed. 2. okt. toimub Estonia kontserdisaalis kontsert K. Arengu 70. juubeli puhul. Rahvusraamatukogus toimub 4. okt. R. Pätsi 100. sünniaastapäevale pühendatud teaduskonverents "Muusikakasvatuse minevik ja tänapäev"

25 CFR 1000.1 - Authority.

Science.gov (United States)

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Authority. 1000.1 Section 1000.1 Indians OFFICE OF THE ASSISTANT SECRETARY, INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ANNUAL FUNDING AGREEMENTS UNDER THE TRIBAL... § 1000.1 Authority. This part is prepared and issued by the Secretary of the Interior under the...

Evaluating FOMC forecast ranges: an interval data approach

OpenAIRE

Henning Fischer; Marta García-Bárzana; Peter Tillmann; Peter Winker

2012-01-01

The Federal Open Market Committee (FOMC) of the U.S. Federal Reserve publishes the range of members' forecasts for key macroeconomic variables, but not the distribution of forecasts within this range. To evaluate these projections, previous papers compare the midpoint of the ranges with the realized outcome. This paper proposes a new approach to forecast evaluation that takes account of the interval nature of projections. It is shown that using the conventional Mincer-Zarnowitz approach to ev...

21 CFR 573.1000 - Verxite.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Verxite. 573.1000 Section 573.1000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS... Listing § 573.1000 Verxite. The food additive verxite may be safely used in animal feed in accordance with...

25 CFR 11.1000 - Complaint.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Complaint. 11.1000 Section 11.1000 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAW AND ORDER COURTS OF INDIAN OFFENSES AND LAW AND ORDER CODE Juvenile Offender Procedure § 11.1000 Complaint. A complaint must be filed by a law enforcement officer or...

EV car sharing/rental pilot project in Kyoto : an outline of the project

Energy Technology Data Exchange (ETDEWEB)

Kitamura, R. [Kyoto Univ., (Japan). Dept. of Civil Engineering Systems; Masunaga, K. [Japan Electric Vehicle Association, Minato, Tokyo (Japan)

2000-07-01

This paper presented a demonstration project in the City of Kyoto, Japan, which is aimed at determining if a Public Car System is an economically viable option for the twenty first century. The Kyoto electric vehicle (EV) car sharing project comprises advanced systems for EV reservation, check-out and return, and fleet operation and management. The most unique feature of this project is that it utilizes the ever expanding Internet and advanced mobile phones with Internet capabilities. Initially, 35 two-seater EVs will be shared by employees and visitors for business-related trips on weekdays and by tourists on weekends. The car sharing will be only short-term for only a single trip. The EV can be checked out and returned to any service depot located at railroad stations, major business centers and tourist attractions for user convenience. The ultimate goal of the project is to promote energy and resource conservation while providing adequate levels of mobility for people. Converting existing fleets to EVs which produce no exhaust gases is considered to be a viable solution to the problem of air pollution caused by traffic jams. tabs., figs.

Transactive Demand Side Management Programs in Smart Grids with High Penetration of EVs

Directory of Open Access Journals (Sweden)

Poria Hasanpor Divshali

2017-10-01

Full Text Available Due to environmental concerns, economic issues, and emerging new loads, such as electrical vehicles (EVs, the importance of demand side management (DSM programs has increased in recent years. DSM programs using a dynamic real-time pricing (RTP method can help to adaptively control the electricity consumption. However, the existing RTP methods, particularly when they consider the EVs and the power system constraints, have many limitations, such as computational complexity and the need for centralized control. Therefore, a new transactive DSM program is proposed in this paper using an imperfect competition model with high EV penetration levels. In particular, a heuristic two-stage iterative method, considering the influence of decisions made independently by customers to minimize their own costs, is developed to find the market equilibrium quickly in a distributed manner. Simulations in the IEEE 37-bus system with 1141 customers and 670 EVs are performed to demonstrate the effectiveness of the proposed method. The results show that the proposed method can better manage the EVs and elastic appliances than the existing methods in terms of power constraints and cost. Also, the proposed method can solve the optimization problem quick enough to run in real-time.

Naistepäev ikka hinnas / Ivar Jung

Index Scriptorium Estoniae

Jung, Ivar

2003-01-01

Kunstihoone galeriis Ivika Kivi ja Dagmar Kase näituse "ID 2002" taustal 8. III toimunud Reet Varblase organiseeritud seminarist "Naised, ühiskond, ilu ja hügieen". Linnagaleriis lõpetas Meiu Mündi maalinäituse Oksana Titova tantsuetendus. 9. III Pärnus Taave Tuutma kureeritud tegevuskunstipäev

A completive survey study on the feasibility and adaptation of EVs in Beijing, China

International Nuclear Information System (INIS)

Sun, Lishan; Huang, Yuchen; Liu, Shuli; Chen, Yanyan; Yao, Liya; Kashyap, Anil

2017-01-01

Highlights: • EVs have been greatly developed with a series of encouraging policies. • The maxi mileages and braking performance still needs further improvement. • More residential and public charging piles should be in the plan and design. • APP oriented information of charging station need to be researched and developed. - Abstract: The private motor vehicles are significantly important means of transportation in modern lifestyle, however, these also contribute to a large proportion of the total air pollution and primary energy consumption. In order to develop green transportation system, it becomes imperative to use integrated technologies to achieve reduced emissions and utilize renewable energy. Electric vehicles (EVs) have been considered as one of these technologies to transform the traditional vehicle mix. However, the uptake of EV has been debated on factors like cost, performance (autonomous mileage), charging point infrastructure construction, energy saving, policy and end users’ adaptation. Present study investigates the technology feasibility (which usually refer to EVs’ cost, EV charging, supplier’s customer services quality, EV travel performance) and users’ adaptation of EV in Beijing, which is a key driver for the EV uptake into the Beijing transportation system. The relevant data have been collected and analyzed in the form of questionnaire survey around all of these factors. While considering the user perception and satisfaction, safety of charging and energy bills have also been investigated. According to the data analysis, it has been found the policy of ‘No traffic restrictions for EVs’ (the traffic restrictions means for certain date, from Monday to Friday the motor vehicles with the last register number of 1 and 6, 2 and 7, 3 and 8, 4 and 9, 5 and 0, are restricted to travel, respectively), the availability of the charging infrastructure and technical support are the most significant factors affecting the users�

New internal multi-range resistors for ac voltage calibration by using TVC

International Nuclear Information System (INIS)

Ali, Rasha S M

2015-01-01

Accurate calibration of ac voltages up to 1000 V by using thermal converters requires range resistors connected in series with the converter. The combination of a thermal converter and range resistor is known as the thermal voltage converter. In this paper, multi-range internal range resistors are designed and implemented in the National Institute for Standards (NIS), Egypt to cover the ac voltage ranges from 10 V to 750 V. The range resistor values are 2 kΩ, 10 kΩ, 20 kΩ, 40 kΩ, 100 kΩ, and 150 kΩ to cover the voltage ranges 10 V, 50 V, 100 V, 200 V, 500 V, and 750 V, respectively. The six range resistors are mounted in series with a single-junction thermo-element in the same box to provide a new thermal voltage converter. The required range resistor is selected by using a six-pin selector switch. Each resistor is connected to a selector pin. The new thermal voltage converter ranges are automatically calibrated against other standard thermal voltage converters at different frequencies by using a LabVIEW program to determine their ac–dc transfer difference at each range. The expanded uncertainties are estimated according to the GUM for all ranges at different frequencies. The performance of the new thermal voltage converter is also evaluated by comparing its ac–dc differences and its accuracy in measuring the ac voltage at different frequencies with a traditional thermal voltage converter. (paper)

Optimization and control method for smart charging of EVs facilitated by Fleet operator

DEFF Research Database (Denmark)

Hu, Junjie; You, Shi; Si, Chengyong

2013-01-01

the energy during the period of high electricity penetration and feed the electricity back into the grid when the demand is high or in situations of insufficient electricity generation. However, the extra loads created by increasing EVs may have adverse impacts on grid. These factors will bring new......-tion and the facilitator EV fleet operator are introduced. Secondly, control architec-tures and their integrations in term of electricity market and distribution grid are discussed. Then, data analysis of EVs including a battery model and driving pattern is presented. Further discussion is given on mathematical modelling...

Correlation between energy deposition and molecular damage from Auger electrons: A case study of ultra-low energy (5–18 eV) electron interactions with DNA

Energy Technology Data Exchange (ETDEWEB)

Rezaee, Mohammad, E-mail: Mohammad.Rezaee@USherbrooke.ca; Hunting, Darel J.; Sanche, Léon [Groupe en Sciences des Radiations, Département de Médecine Nucléaire et Radiobiologie, Faculté de Médecine et des Sciences de la Santé, Université de Sherbrooke, Sherbrooke, Québec J1H 5N4 (Canada)

2014-07-15

Purpose: The present study introduces a new method to establish a direct correlation between biologically related physical parameters (i.e., stopping and damaging cross sections, respectively) for an Auger-electron emitting radionuclide decaying within a target molecule (e.g., DNA), so as to evaluate the efficacy of the radionuclide at the molecular level. These parameters can be applied to the dosimetry of Auger electrons and the quantification of their biological effects, which are the main criteria to assess the therapeutic efficacy of Auger-electron emitting radionuclides. Methods: Absorbed dose and stopping cross section for the Auger electrons of 5–18 eV emitted by{sup 125}I within DNA were determined by developing a nanodosimetric model. The molecular damages induced by these Auger electrons were investigated by measuring damaging cross section, including that for the formation of DNA single- and double-strand breaks. Nanoscale films of pure plasmid DNA were prepared via the freeze-drying technique and subsequently irradiated with low-energy electrons at various fluences. The damaging cross sections were determined by employing a molecular survival model to the measured exposure–response curves for induction of DNA strand breaks. Results: For a single decay of{sup 125}I within DNA, the Auger electrons of 5–18 eV deposit the energies of 12.1 and 9.1 eV within a 4.2-nm{sup 3} volume of a hydrated or dry DNA, which results in the absorbed doses of 270 and 210 kGy, respectively. DNA bases have a major contribution to the deposited energies. Ten-electronvolt and high linear energy transfer 100-eV electrons have a similar cross section for the formation of DNA double-strand break, while 100-eV electrons are twice as efficient as 10 eV in the induction of single-strand break. Conclusions: Ultra-low-energy electrons (<18 eV) substantially contribute to the absorbed dose and to the molecular damage from Auger-electron emitting radionuclides; hence, they should

Regional mapping of photovoltaic plants ranging from 100 to 999 kWc in 2013

International Nuclear Information System (INIS)

Anon.

2013-01-01

In a context of the expectation of a strong political lead, small and intermediate photovoltaic installations keep on developing. The map gives for each France's region the number of operating installations whose power output ranges between 100 and 999 kWc, and the number and the capacity of the installations that are completed but not yet connected to the grid. The sunshine level curves are also drawn. Polycrystal and monocrystal technologies are the most used 48% and 32% respectively, while the thin layer technology is used in only 5% of the installations. Concerning the type of the setting a great majority of the installations (85%) are integrated to the building while less than 1% are set on the ground. (A.C.)

Hierarchical Agent-Based Integrated Modelling Approach for Microgrids with Adoption of EVs and HRES

Directory of Open Access Journals (Sweden)

Peng Han

2014-01-01

Full Text Available The large adoption of electric vehicles (EVs, hybrid renewable energy systems (HRESs, and the increasing of the loads shall bring significant challenges to the microgrid. The methodology to model microgrid with high EVs and HRESs penetrations is the key to EVs adoption assessment and optimized HRESs deployment. However, considering the complex interactions of the microgrid containing massive EVs and HRESs, any previous single modelling approaches are insufficient. Therefore in this paper, the methodology named Hierarchical Agent-based Integrated Modelling Approach (HAIMA is proposed. With the effective integration of the agent-based modelling with other advanced modelling approaches, the proposed approach theoretically contributes to a new microgrid model hierarchically constituted by microgrid management layer, component layer, and event layer. Then the HAIMA further links the key parameters and interconnects them to achieve the interactions of the whole model. Furthermore, HAIMA practically contributes to a comprehensive microgrid operation system, through which the assessment of the proposed model and the impact of the EVs adoption are achieved. Simulations show that the proposed HAIMA methodology will be beneficial for the microgrid study and EV’s operation assessment and shall be further utilized for the energy management, electricity consumption prediction, the EV scheduling control, and HRES deployment optimization.

Immunogenicity Studies of Bivalent Inactivated Virions of EV71/CVA16 Formulated with Submicron Emulsion Systems

Directory of Open Access Journals (Sweden)

Chih-Wei Lin

2014-01-01

Full Text Available We assessed two strategies for preparing candidate vaccines against hand, foot, and mouth disease (HFMD caused mainly by infections of enterovirus (EV 71 and coxsackievirus (CV A16. We firstly design and optimize the potency of adjuvant combinations of emulsion-based delivery systems, using EV71 candidate vaccine as a model. We then perform immunogenicity studies in mice of EV71/CVA16 antigen combinations formulated with PELC/CpG. A single dose of inactivated EV71 virion (0.2 μg emulsified in submicron particles was found (i to induce potent antigen-specific neutralizing antibody responses and (ii consistently to elicit broad antibody responses against EV71 neutralization epitopes. A single dose immunogenicity study of bivalent activated EV71/CVA16 virion formulated with either Alum or PELC/CpG adjuvant showed that CVA16 antigen failed to elicit CVA16 neutralizing antibody responses and did not affect EV71-specific neutralizing antibody responses. A boosting dose of emulsified EV71/CVA16 bivalent vaccine candidate was found to be necessary to achieve high seroconversion of CVA16-specific neutralizing antibody responses. The current results are important for the design and development of prophylactic vaccines against HFMD and other emerging infectious diseases.

Charging kinetics in virgin and 1 MeV-electron irradiated yttria-stabilized zirconia in the 300-1000 K range

International Nuclear Information System (INIS)

Thome, T.; Braga, D.; Blaise, G.; Cousty, J.; Pham Van, L.; Costantini, J.M.

2006-01-01

A study performed with a dedicated scanning electron microscope (SEM) on the surface electrical properties of (1 0 0)-oriented yttria-stabilized zirconia (YSZ) single crystals irradiated with 1 MeV electrons is presented. When compared with virgin YSZ, the 1 MeV-irradiated YSZ shows a decrease of the intrinsic total electron emission coefficient σ 0 and an increase of the time constant τ associated with the charging kinetics of the material at room temperature. These measurements performed with the SEM beam at 10 keV indicate that the defects induced by the 1 MeV-electron irradiation generate a positive electric field of the order of 0.5 x 10 6 V/m at a depth of about 1 μm that prevents electrons to escape. When the SEM beam with a 1.1 keV energy is used, a smaller field (∼0.5 x 10 3 V/m) is detected closer to the surface (∼20 nm). The fading of these fields during the thermal annealing in the 400-1000 K temperature range provides information on the nature of defects induced by the 1 MeV-electron irradiation

30 CFR 250.1000 - General requirements.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false General requirements. 250.1000 Section 250.1000... OPERATIONS IN THE OUTER CONTINENTAL SHELF Pipelines and Pipeline Rights-of-Way § 250.1000 General....1001, must meet the requirements in §§ 250.1000 through 250.1008. (2) A pipeline right-of-way grant...

7 CFR 1000.54 - Equivalent price.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Equivalent price. 1000.54 Section 1000.54 Agriculture... Prices § 1000.54 Equivalent price. If for any reason a price or pricing constituent required for computing the prices described in § 1000.50 is not available, the market administrator shall use a price or...

Coupled-channel optical calculation of electron-atom scattering: elastic scattering from sodium at 20 to 150 eV

International Nuclear Information System (INIS)

Bray, Igor; Konovalov, D.A.; McCarthy, I.E.

1991-04-01

A coupled-channel optical method for electron-atom scattering is applied to elastic electron-sodium scattering at energies of 20, 22.1, 54.4, 100, and 150 eV. It is demonstrated that the effect of all the inelastic channels on elastic scattering may be well reproduced by the 'ab initio' calculated complex non-local polarization potential. Whilst the experiments generally agree at small angles and therefore agree on the total elastic cross section, there is considerable discrepancy at intermediate and backward angles. 9 refs., 2 tabs., 1 fig

Tensile properties and fracture mechanism of IN-100 superalloy in high temperature range

Directory of Open Access Journals (Sweden)

Milan T. Jovanović

2017-06-01

Full Text Available Tensile properties and fracture mechanism of a polycrystalline IN-100 superalloy have been investigated in the range from room temperature to 900°C. Optical microscopy (OM and transmission electron microscopy (TEM applying replica technique were used for microstructural investigation, whereas scanning electron microscopy (SEM was utilized for fracture study. High temperature tensile tests were carried out in vacuumed chamber. Results show that strength increases up to 700°C, and then sharply decreases with further increase in temperature. Elongation increases very slowly (6-7.5% till 500°C, then decreases to 4.5% at 900°C. Change in elongation may be ascribed to a change of fracture mechanism. Appearance of a great number of microvoids prevails up to 500°C resulting in a slow increase of elongation, whereas above this temperature elongation decrease is correlated with intergranular crystallographic fracture and fracture of carbides.

Long-range high-speed visible light communication system over 100-m outdoor transmission utilizing receiver diversity technology

Science.gov (United States)

Wang, Yiguang; Huang, Xingxing; Shi, Jianyang; Wang, Yuan-quan; Chi, Nan

2016-05-01

Visible light communication (VLC) has no doubt become a promising candidate for future wireless communications due to the increasing trends in the usage of light-emitting diodes (LEDs). In addition to indoor high-speed wireless access and positioning applications, VLC usage in outdoor scenarios, such as vehicle networks and intelligent transportation systems, are also attracting significant interest. However, the complex outdoor environment and ambient noise are the key challenges for long-range high-speed VLC outdoor applications. To improve system performance and transmission distance, we propose to use receiver diversity technology in an outdoor VLC system. Maximal ratio combining-based receiver diversity technology is utilized in two receivers to achieve the maximal signal-to-noise ratio. A 400-Mb/s VLC transmission using a phosphor-based white LED and a 1-Gb/s wavelength division multiplexing VLC transmission using a red-green-blue LED are both successfully achieved over a 100-m outdoor distance with the bit error rate below the 7% forward error correction limit of 3.8×10-3. To the best of our knowledge, this is the highest data rate at 100-m outdoor VLC transmission ever achieved. The experimental results clearly prove the benefit and feasibility of receiver diversity technology for long-range high-speed outdoor VLC systems.

Symmetric charge transfer cross section of uranium

International Nuclear Information System (INIS)

Shibata, Takemasa; Ogura, Koichi

1995-03-01

Symmetric charge transfer cross section of uranium was calculated under consideration of reaction paths. In the charge transfer reaction a d 3/2 electron in the U atom transfers into the d-electron site of U + ( 4 I 9/2 ) ion. The J value of the U atom produced after the reaction is 6, 5, 4 or 3, at impact energy below several tens eV, only resonant charge transfer in which the product atom is ground state (J=6) takes place. Therefore, the cross section is very small (4-5 x 10 -15 cm 2 ) compared with that considered so far. In the energy range of 100-1000eV the cross section increases with the impact energy because near resonant charge transfer in which an s-electron in the U atom transfers into the d-electron site of U + ion. Charge transfer cross section between U + in the first excited state (289 cm -1 ) and U in the ground state was also obtained. (author)

Measurement of barrier height of Pd on diamond (100) surface by X-ray photoelectron spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Li, F.N. [Institute of Wide Band Gap Semiconductors, Xi' an Jiaotong University, Xi' an 710049 (China); Nation Key Laboratory of ASIC, HSRI, Shijiazhuang 050051 (China); Liu, J.W. [International Center for Young Scientists, National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba, Ibaraki 3050044 (Japan); Zhang, J.W.; Wang, X.L.; Wang, W.; Liu, Z.C. [Institute of Wide Band Gap Semiconductors, Xi' an Jiaotong University, Xi' an 710049 (China); Wang, H.X., E-mail: hxwangcn@mail.xjtu.edu.cn [Institute of Wide Band Gap Semiconductors, Xi' an Jiaotong University, Xi' an 710049 (China)

2016-05-01

Highlights: • Metal-semiconductor contacts of Pd/hydrogen-terminated diamond and Pd/oxygen-terminated diamond have been investigated by XPS measurements. • The barrier height for Pd/hydrogen-terminated diamond (ohmic contact) has been measured to be −0.27 eV. • The barrier height for Pd/oxygen-terminated diamond (Schottky contact) has been measured to be 1.73 eV. - Abstract: Barrier height (Φ{sub BH}) values for Pd/hydrogen-terminated diamond (H-diamond) and Pd/oxygen-terminated diamond (O-diamond) have been investigated by X-ray photoelectron spectroscopy technique. H-diamond and O-diamond have been formed on the same diamond (100) layer grown by microwave plasma-enhanced chemical vapor deposition,on which Pd layers have been evaporated. The Φ{sub BH} values for Pd/H-diamond and Pd/O-diamond are determined to be −0.27 eV and 1.73 eV, respectively. It indicates that Pd is a suitable metal for ohmic and Schottky contacts on H-diamond and O-diamond, respectively. The experimental Φ{sub BH} values are in good agreement with the theoretical calculation results.

24 CFR 1000.28 - May a self-governance Indian tribe be exempted from the applicability of § 1000.26?

Science.gov (United States)

2010-04-01

... be exempted from the applicability of § 1000.26? 1000.28 Section 1000.28 Housing and Urban... ACTIVITIES General § 1000.28 May a self-governance Indian tribe be exempted from the applicability of § 1000... and systems meet or exceed the comparable requirements of § 1000.26. For purposes of this section, a...

Comparison of the LEGO Mindstorms NXT and EV3 Robotics Education Platforms

Science.gov (United States)

Sherrard, Ann; Rhodes, Amy

2014-01-01

The release of the latest LEGO Mindstorms EV3 robotics platform in September 2013 has provided a dilemma for many youth robotics leaders. There is a need to understand the differences in the Mindstorms NXT and EV3 in order to make future robotics purchases. In this article the differences are identified regarding software, hardware, sensors, the…

Control parameter optimization for AP1000 reactor using Particle Swarm Optimization

International Nuclear Information System (INIS)

Wang, Pengfei; Wan, Jiashuang; Luo, Run; Zhao, Fuyu; Wei, Xinyu

2016-01-01

Highlights: • The PSO algorithm is applied for control parameter optimization of AP1000 reactor. • Key parameters of the MSHIM control system are optimized. • Optimization results are evaluated though simulations and quantitative analysis. - Abstract: The advanced mechanical shim (MSHIM) core control strategy is implemented in the AP1000 reactor for core reactivity and axial power distribution control simultaneously. The MSHIM core control system can provide superior reactor control capabilities via automatic rod control only. This enables the AP1000 to perform power change operations automatically without the soluble boron concentration adjustments. In this paper, the Particle Swarm Optimization (PSO) algorithm has been applied for the parameter optimization of the MSHIM control system to acquire better reactor control performance for AP1000. System requirements such as power control performance, control bank movement and AO control constraints are reflected in the objective function. Dynamic simulations are performed based on an AP1000 reactor simulation platform in each iteration of the optimization process to calculate the fitness values of particles in the swarm. The simulation platform is developed in Matlab/Simulink environment with implementation of a nodal core model and the MSHIM control strategy. Based on the simulation platform, the typical 10% step load decrease transient from 100% to 90% full power is simulated and the objective function used for control parameter tuning is directly incorporated in the simulation results. With successful implementation of the PSO algorithm in the control parameter optimization of AP1000 reactor, four key parameters of the MSHIM control system are optimized. It has been demonstrated by the calculation results that the optimized MSHIM control system parameters can improve the reactor power control capability and reduce the control rod movement without compromising AO control. Therefore, the PSO based optimization

Chemical track effects in condensed systems and implications for biological damage

International Nuclear Information System (INIS)

Magee, J.L.; Chatterjee, A.

1979-01-01

The spatial distributions of reactive intermediates, chemical reactions, and products are involved in the chemical interests in particle tracks. Biological systems are considred to be concentrated aqueous solutions, and the reactions of biological molecules can occur at any time including prethermal period. Heavy particles lose approximately equal amounts of energy by two mechanisms which lead to the different patterns of energy deposit; that is, the resonant process with individual losses in the range of 0 - 100 eV, and the knock-on process which creates recoil electrons in spectra from 100 eV to the maximum. The survival of cultured cells after irradiation depends on certain parameters of the radiation. Such theories seem to imply that the deposit of energy in the proper location of a cell can guarantee its death, that is, there is all-or-none effect, dependent solely on the absorption of energy. The initial dissociation of water is assumed to require 17 eV. A weakness regarding heavy particle tracks is the lack of knowledge on the phenomena that occur at extremely high energy deposit, approximately 1000 eV per A. Significantly high temperature must be generated, accompanied by shock waves and bubble formation. In a radical diffusion model for cell survival, it is assumed that a particular type of the lesion of DNA may be formed by a purely chemical process which can provide a certain lethality. The chemical processes following the energy deposit by high energy particles are known at least in approximate way, including most of the phenomena in space and time. (Yamashita, S.)

1000–ton testing machine for cyclic fatigue tests of materials at liquid nitrogen temperatures

Energy Technology Data Exchange (ETDEWEB)

Khitruk, A. A.; Klimchenko, Yu. A.; Kovalchuk, O. A.; Marushin, E. L.; Mednikov, A. A.; Nasluzov, S. N.; Privalova, E. K.; Rodin, I. Yu.; Stepanov, D. B.; Sukhanova, M. V. [The D.V. Efremov Scientific Research Institute of Electrophysical Apparatus (NIIEFA), 3 Doroga na Metallostroy, Metallostroy, Saint Petersburg 196641 (Russian Federation)

2014-01-29

One of the main tasks of superconductive magnets R and D is to determine the mechanical and fatigue properties of structural materials and the critical design elements in the cryogenic temperature range. This paper describes a new facility built based on the industrial 1000-ton (10 MN) testing machine Schenk PC10.0S. Special equipment was developed to provide the mechanical and cyclic tensile fatigue tests of large-scale samples at the liquid nitrogen temperature and in a given load range. The main feature of the developed testing machine is the cryostat, in which the device converting a standard compression force of the testing machine to the tensile force affected at the test object is placed. The control system provides the remote control of the test and obtaining, processing and presentation of test data. As an example of the testing machine operation the test program and test results of the cyclic tensile fatigue tests of fullscale helium inlet sample of the PF1 coil ITER are presented.

1000–ton testing machine for cyclic fatigue tests of materials at liquid nitrogen temperatures

International Nuclear Information System (INIS)

Khitruk, A. A.; Klimchenko, Yu. A.; Kovalchuk, O. A.; Marushin, E. L.; Mednikov, A. A.; Nasluzov, S. N.; Privalova, E. K.; Rodin, I. Yu.; Stepanov, D. B.; Sukhanova, M. V.

2014-01-01

One of the main tasks of superconductive magnets R and D is to determine the mechanical and fatigue properties of structural materials and the critical design elements in the cryogenic temperature range. This paper describes a new facility built based on the industrial 1000-ton (10 MN) testing machine Schenk PC10.0S. Special equipment was developed to provide the mechanical and cyclic tensile fatigue tests of large-scale samples at the liquid nitrogen temperature and in a given load range. The main feature of the developed testing machine is the cryostat, in which the device converting a standard compression force of the testing machine to the tensile force affected at the test object is placed. The control system provides the remote control of the test and obtaining, processing and presentation of test data. As an example of the testing machine operation the test program and test results of the cyclic tensile fatigue tests of fullscale helium inlet sample of the PF1 coil ITER are presented

AP1000. The PWR revisited

International Nuclear Information System (INIS)

Gaio, P.

2006-01-01

The distinguishing features of Westinghouse's AP1000 advanced passive pressurized water reactor are highlighted. In particular, the AP1000's passive safety features are described as well as their implications for simplifying the design, construction, and operation of this design compared to currently operating plants, and significantly increasing safety margins over current plants as well. The AP1000 design specifically incorporates the knowledge acquired from the substantial accumulation of power reactor operating experience and benefits from the application of the Probabilistic Risk Assessment in the design process itself. The AP1000 design has been certified by the US Nuclear Regulatory Commission under its new rules for licensing new nuclear plants, 10 CFR Part 52, and is the subject of six combined Construction and Operating License applications now being developed. Currently the AP1000 design is being assessed against the EUR Rev C requirements for new nuclear power plants in Europe. (author)

EV Everywhere Grand Challenge Road to Success

Energy Technology Data Exchange (ETDEWEB)

None, None

2014-01-31

Initial progress report for EV Everywhere. The report highlights the significant cost reduction in batteries in 2014, which will enable increased PEV affordability for consumers. Also, the efforts on increasing the convenience of PEVs through the Workplace Charging Challenge, which called on U.S. employers to help develop the nation's charging infrastructure.

A 100,000 Scale Factor Radar Range.

Science.gov (United States)

Blanche, Pierre-Alexandre; Neifeld, Mark; Peyghambarian, Nasser

2017-12-19

The radar cross section of an object is an important electromagnetic property that is often measured in anechoic chambers. However, for very large and complex structures such as ships or sea and land clutters, this common approach is not practical. The use of computer simulations is also not viable since it would take many years of computational time to model and predict the radar characteristics of such large objects. We have now devised a new scaling technique to overcome these difficulties, and make accurate measurements of the radar cross section of large items. In this article we demonstrate that by reducing the scale of the model by a factor 100,000, and using near infrared wavelength, the radar cross section can be determined in a tabletop setup. The accuracy of the method is compared to simulations, and an example of measurement is provided on a 1 mm highly detailed model of a ship. The advantages of this scaling approach is its versatility, and the possibility to perform fast, convenient, and inexpensive measurements.

Nature of monovacancies on quasi-hexagonal structure of reconstructed Au(100) surface

Energy Technology Data Exchange (ETDEWEB)

Pieczyrak, Barbara; Trembulowicz, Artur; Antczak, Grażyna, E-mail: antczak@ifd.uni.wroc.pl; Jurczyszyn, Leszek

2017-06-15

Highlights: • Surprising nature of surface monovacancies: spontaneous healing. • Determination of vacancy formation energy in the range of 0.34–0.55 eV. • A good agreement between the theoretical (DFT) and experimental (STM) data. - Abstract: Density functional theory and the scanning tunneling microscopy were applied to investigate the nature of the defects on an unrotated reconstructed hexagonal Au(100) surface. We show the correlation between the nature of monovacancies and the geometrical arrangement of the atoms from the first (topmost) layer with respect to the second layer. The vacancies created directly above the atoms from the second layer (on-top position) move spontaneously into the subsurface upon relaxation. For the vacancies created in other places, the subsurface shift is hindered by the energy barrier and the lifted subsurface atom is in the interlayer position. Charge density calculations were compared with results from the scanning tunneling microscopy images which show a good agreement between the theoretical and experimental data.

Studies on keV and eV electrons in solids

International Nuclear Information System (INIS)

Schou, J.

1979-10-01

The interaction between keV or eV electrons and solids was studied. The results presented mostly concern problems in connection with electron irradiation of solids, but to some extent they also include ion-induced secondary electron emission. The experiments were mainly performed on solidified gases using 1 - 3 keV electrons. The projected range of electrons was determined in solid hydrogen, deuterium and nitrogen. The true secondary electron emission coefficient and the electron reflection coefficient of solid hydrogen, deuterium and nitrogen were measured. The escape depth of the true secondary electrons in nitrogen was determined. The angular dependence of both the reflection coefficient and the true secondary electron emission coefficient of solid hydrogen and deuterium was investigated. Both ion- and electron-induced secondary electron emission were treated theoretically on the basis of ionization cascade theory. (Auth.)

Optimal Design of DC Fast-Charging Stations for EVs in Low Voltage Grids

DEFF Research Database (Denmark)

Gjelaj, Marjan; Træholt, Chresten; Hashemi Toghroljerdi, Seyedmostafa

2017-01-01

DC Fast Charging Station (DCFCS) is essential for widespread use of Electric Vehicle (EVs). It can recharge EVs in direct current in a short period of time. In recent years, the increasing penetration of EVs and their charging systems are going through a series of changes. This paper addresses...... on the power grid through the application of electrical storage systems within the DC fast charging stations. The proposed solution decreases the charging time and the impact on the low voltage (LV) grid significantly. The charger can be used as a multifunctional grid-utility such as congestion management...

EV Charging Analysis Based on the National Travel Surveys of the Nordic Area

DEFF Research Database (Denmark)

Liu, Zhaoxi; Wu, Qiuwei

2014-01-01

This paper presents the charging demand profiles of electric vehicles (EVs) based on the National Travel Surveys of the Nordic area. The EV charging analysis is carried out considering different types of charging patterns which are dumb charging, timed charging and spot price based charging....... The driving behavior of the vehicles is studied through the National Travel Surveys of Denmark, Finland, Norway and Sweden. The features of the charging demand are discussed based on the results of the analysis. The study in this paper provides an estimation of the possible level and patterns of the EV...

Generation of colour centres in yttria-stabilized zirconia by heavy ion irradiations in the GeV range

International Nuclear Information System (INIS)

Costantini, Jean-Marc; Beuneu, Francois; Schwartz, Kurt; Trautmann, Christina

2010-01-01

We have studied the colour centre production in yttria-stabilized zirconia (ZrO 2 :Y 3+ ) by heavy ion irradiation in the GeV range using on-line UV-visible optical absorption spectroscopy. Experiments were performed with 11.4 MeV amu -1 127 Xe, 197 Au, 208 Pb and 238 U ion irradiations at 8 K or room temperature (RT). A broad and asymmetrical absorption band peaked at a wavelength about 500 nm is recorded regardless of the irradiation parameters, in agreement with previous RT irradiations with heavy ions in the 100 MeV range. This band is de-convoluted into two broad Gaussian-shaped bands centred at photon energies about 2.4 and 3.1 eV that are respectively associated with the F + -type centres (involving a singly ionized oxygen vacancy, V O · ) and T centres (i.e. Zr 3+ in a trigonal symmetry) observed by electron paramagnetic resonance (EPR) spectroscopy. In the case of 8 K Au ion irradiation at low fluences, six bands are used at about 1.9, 2.3, 2.7, 3.1 and 4.0 eV. The three bands near 2.0-2.5 eV can be assigned to oxygen divacancies (i.e. F 2 + centres). No significant effect of the irradiation temperature is found on the widths of all absorption bands for the same ion and fluence. This is attributed to the inhomogeneous broadening arising from the static disorder due to the native charge-compensating oxygen vacancies. However, the colour centre production yield is strongly enhanced at 8 K with respect to RT. When heating irradiated samples from 8 K to RT, the extra colour centres produced at low temperature do not recover completely to the level of RT irradiation. The latter results are accounted for by an electronically driven defect recovery process.

A Comprehensive Study of Key Electric Vehicle (EV Components, Technologies, Challenges, Impacts, and Future Direction of Development

Directory of Open Access Journals (Sweden)

Fuad Un-Noor

2017-08-01

Full Text Available Electric vehicles (EV, including Battery Electric Vehicle (BEV, Hybrid Electric Vehicle (HEV, Plug-in Hybrid Electric Vehicle (PHEV, Fuel Cell Electric Vehicle (FCEV, are becoming more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace internal combustion engine (ICE vehicles in the near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system could face huge instabilities with enough EV penetration, but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of the smart grid concept. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emissions produced by the transportation sector. However, there are some major obstacles for EVs to overcome before totally replacing ICE vehicles. This paper is focused on reviewing all the useful data available on EV configurations, battery energy sources, electrical machines, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

Measurement of the 238U subthreshold fission cross section for incident neutron energies between 0.6 and 100 keV

International Nuclear Information System (INIS)

Difilippo, F.C.; Perez, R.B.; de Saussure, G.; Olsen, D.K.; Ingle, R.W.

1977-01-01

The neutron-induced 238 U subthreshold fission cross section has been measured in the neutron energy range between 0.6 and 100 keV. A total of 28 fission clusters were identified. The well-known clusters at 721 and 1210 eV appeared resolved into their Class I components. Average 238 U subthreshold fission cross sections were determined and compared with available results in the literature. The measurement is interpreted in terms of fission doorway (Class II levels) arising from the assumption of the existence of a double-humped fission barrier for the ( 238 U + n) compound nucleus at large deformations. On the basis of this model, several fission barrier parameters were determined

Cascades from nu_E above 1020 eV

Energy Technology Data Exchange (ETDEWEB)

Klein, Spencer R.

2004-12-21

At very high energies, the Landau-Pomeranchuk-Migdal effect reduces the cross sections for electron bremsstrahlung and photon e{sup +}e{sup -} pair production. The fractional electron energy loss and pair production cross sections drop as the energy increases. In contrast, the cross sections for photonuclear interactions grow with energy. In solids and liquids, at energies above 10{sup 20} eV, photonuclear reactions dominate, and showers that originate as photons or electrons quickly become hadronic showers. These electron-initiated hadronic showers are much shorter (due to the absence of the LPM effect), but wider than purely electromagnetic showers would be. This change in shape alters the spectrum of the electromagnetic and acoustic radiation emitted from the shower. These alterations have important implications for existing and planned searches for radiation from u{sub e} induced showers above 10{sup 20} eV, and some existing limits should be reevaluated.

HLA diversity in the 1000 genomes dataset.

Directory of Open Access Journals (Sweden)

Pierre-Antoine Gourraud

Full Text Available The 1000 Genomes Project aims to provide a deep characterization of human genome sequence variation by sequencing at a level that should allow the genome-wide detection of most variants with frequencies as low as 1%. However, in the major histocompatibility complex (MHC, only the top 10 most frequent haplotypes are in the 1% frequency range whereas thousands of haplotypes are present at lower frequencies. Given the limitation of both the coverage and the read length of the sequences generated by the 1000 Genomes Project, the highly variable positions that define HLA alleles may be difficult to identify. We used classical Sanger sequencing techniques to type the HLA-A, HLA-B, HLA-C, HLA-DRB1 and HLA-DQB1 genes in the available 1000 Genomes samples and combined the results with the 103,310 variants in the MHC region genotyped by the 1000 Genomes Project. Using pairwise identity-by-descent distances between individuals and principal component analysis, we established the relationship between ancestry and genetic diversity in the MHC region. As expected, both the MHC variants and the HLA phenotype can identify the major ancestry lineage, informed mainly by the most frequent HLA haplotypes. To some extent, regions of the genome with similar genetic or similar recombination rate have similar properties. An MHC-centric analysis underlines departures between the ancestral background of the MHC and the genome-wide picture. Our analysis of linkage disequilibrium (LD decay in these samples suggests that overestimation of pairwise LD occurs due to a limited sampling of the MHC diversity. This collection of HLA-specific MHC variants, available on the dbMHC portal, is a valuable resource for future analyses of the role of MHC in population and disease studies.

The behavior of the Tevatron at energies greater than 1000 GeV

International Nuclear Information System (INIS)

Pogorelko, O.

1991-04-01

If, as appears likely, the top quark lies at the upper range of the mass reach of the Tevatron, then increasing the energy of the collider operation could prove to be a crucial factor in the future program together with projected luminosity enhancements. While a significant amount of data exists on individual magnets up to an energy of 1000 GeV, there are no detailed measurements above this value. We focus on the operating range beyond 1000 GeV in an attempt to see whether there is any realistic opportunity to extend the energy range of the Tevatron into this regime. The proposed modifications to the Tevatron Cryogenic System will provide sufficient cooling to lower the operating temperature of the 1000 superconducting magnets from the present 4.6--4.8K (1-φ inlet temperature) down to a range of 3.6--3.8K. At this temperature the short sample quench current for the dipole magnets should increase from the present value of ∼4000A (900 GeV) up to a level approaching 4800A (1100 GeV.) Increasing the peak current in the dipoles produces some important questions related to possible mechanical effects including catastrophic failure, the change of magnetic field quality, and quench protection problems resulting from the increased stored energy. In this note we shall examine these effects and comment on the existing data on low temperature operation. We have only considered the dipole magnets since the quadrupoles should not limit performance. We have not looked at the interaction region magnets which involve different considerations

Energy spectrum of primary cosmic rays from 1016eV to 1019eV determined from air showers observed at 5200 m a.s.l

International Nuclear Information System (INIS)

Aguirre, C.; Mejia, G.R.; Yoshii, H.; Toyoda, Y.

1977-01-01

Energy spectra of primary cosmic rays from 10 16 eV to 10 19 eV have been determined from electron-sizes as well as from muon-sizes of the same air showers observed at Mt. Chacaltaya. The spectrum from electron-sizes is significantly higher than that from muon-sizes. The discrepancy is discussed and an explanation is given under the assumption of possible existence of copious direct production of photons besides the production of charged and neutral pions at these high energies. The spectra are also compared with those by other groups and the discrepancies are discussed. (author)

UNITI Bundesverband mittelstaendischer Mineraloelunternehmen e.V.. Annual report 2011/2012; UNITI Bundesverband mittelstaendischer Mineraloelunternehmen e.V.. Jahresbericht 2011/2012

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

The report presents the organisational structure and activities of the UNITI Bundesverband mittelstaendischer Mineraloelunternehmen e.V. (Berlin, Federal Republic of Germany). Above all, topical issues on business in the mineral oil and lubricant sector are discussed. There is an appendix containing data on the production and sales of petroleum products in the Federal Republic of Germany.

Can LENR Energy Gains Exceed 1000?

Science.gov (United States)

Nagel, David J.

2011-03-01

Energy gain is defined as the energy realized from reactions divided by the energy required to produce those reactions. Low Energy Nuclear Reactions (LENR) have already been measured to significantly exceed the energy gain of 10 projected from ITER,possibly 15 years from now. Electrochemical experiments using the Pd-D system have shown energy gains exceeding 10. Gas phase experiments with the Ni-H system were reported to yield energy gains of over 100. Neither of these reports has been adequately verified or reproduced. However, the question in the title still deserves consideration. If, as thought by many, it is possible to trigger nuclear reactions that yield MeV energies with chemical energies of the order of eV, then the most optimistic expectation is that LENR gains could approach one million. Hence, the very tentative answer to the question above is yes. However, if LENR could be initiated with some energy cost, and then continue to ``burn,'' very high energy gains might be realized. Consider a match and a pile of dry logs. The phenomenon termed ``heat after death'' will be examined to see if it might be the initial evidence for nuclear ``burning.''

Coupled-channel optical calculation of electron-hydrogen scattering: elastic scattering from 0.5 to 30 eV

International Nuclear Information System (INIS)

Bray, I.; Konovalov, D.A.; McCarthy, I.E.

1991-01-01

A coupled-channel optical method for electron-atomic hydrogen scattering is presented in a form that treats both the projectile and the target electrons symmetrically. Elastic differential cross sections are calculated at a range of energies from 0.5 to 30 eV and are found to be in complete agreement with the absolute measurements, previously reported. Total and total ionization cross sections are also presented. 13 refs., 2 tabs., 2 figs

Lattice parameters and thermal expansion of delta-VNsub(1-x) from 298-1000 K

International Nuclear Information System (INIS)

Lengauer, W.; Ettmayer, P.

1986-01-01

The thermal expansion of VNsub(1-x) was determined from measurements of the lattice parameters in the temperature range of 298-1000 K and in the composition range of VNsub(0.707) - VNsub(0.996). Within the accuracy of the results the expansion of the lattice parameter with temperature is not dependent on the composition. The lattice parameter as a function of composition ([N]/[V] = 0.707-0.996) and temperature (198-1000 K) is given by a([N]/[V], T) = 0.38872+0.02488 ([N]/[V]) - (1.083+-0.021) x 10 -4 Tsup(1/2) + (6.2+-0.1) x 10 - sup6T. The coefficient of linear thermal expansion as a function of temperature (in the same range) is given by α(T) = a([N]/[V], T) -1 [(-5.04+-0.01) x 10 -5 Tsup(1/2) + (6.2+-0.1) x 10 -6 ]. The average linear thermal expansion coefficient is αsub(av) = 9.70 +- 0.15 x 10 -6 K -1 (298-1000 K). The data are compared with those of several fcc transition metal nitrides collected and evaluated from the literature. (Author)

Data of evolutionary structure change: 1EV4D-2OADA [Confc[Archive

Lifescience Database Archive (English)

Full Text Available 1EV4D-2OADA 1EV4 2OAD D A SGKPVLHYFNARGRMECIRFLLAAAGVEFDEKFIQSPED...ine> ASP CA 238 2OAD A 2OADA...bID>2OAD A 2OADA LLSQNQGGKAFI...2OAD A 2OADA EEVVT-----IDTWM ...ID> 3 2OAD A 2OADA

Circular intensity differential scattering (CIDS) measurements in the soft x-ray region of the spectrum (∼16 eV to 500 eV)

International Nuclear Information System (INIS)

Maestre, M.F.; Bustamante, C.; Snyder, P.; Rowe, E.; Hansen, R.

1991-03-01

We propose the use of recently developed techniques of circular intensity differential scattering (CIDS), as extended to the soft x-ray region of the spectrum (16 eV to 500 eV), to study the higher order organization of the eukaryotic chromosome. CIDS is the difference in scattering power of an object when illuminated by right circularly polarized vs. left circularly polarized electromagnetic radiation of arbitrary wavelength. CIDS has been shown to be a very sensitive measure of the helical organization of the scattering object eg. the eukaryotic chromosome. Preliminary results of measurements of samples of bacteriophages and octopus sperm done at SRC, Wisconsin, show the technique to be very sensitive to the dimensional parameters of the particles interrogated by circularly polarized light. 7 refs., 5 figs

Super cool X-1000 and Super cool Z-1000, two ice blockers, and their effect on vitrification/warming of mouse embryos.

Science.gov (United States)

Badrzadeh, H; Najmabadi, S; Paymani, R; Macaso, T; Azadbadi, Z; Ahmady, A

2010-07-01

To evaluate the survival and blastocyst formation rates of mouse embryos after vitrification/thaw process with different ice blocker media. We used X-1000 and Z-1000 separately and mixed using V-Kim, a closed vitrification system. Mouse embryos were vitrified using ethylene glycol based medium supplemented with Super cool X-1000 and/or Super cool Z-1000. Survival rates for the control, Super cool X-1000, Super cool Z-1000, and Super cool X-1000/Z-1000 groups were 74%, 72%, 68%, and 85% respectively, with no significant difference among experimental and control groups; however, a significantly higher survival rate was noticed in the Super cool X-1000/Z-1000 group when compared with the Super cool Z-1000 group. Blastocyst formation rates for the control, Super cool X-1000, Super cool Z-1000, and Super cool X-1000/Z-1000 groups were 71%, 66%, 65%, and 72% respectively. There was no significant difference in this rate among control and experimental groups. In a closed vitrification system, addition of ice blocker Super cool X-1000 to the vitrification solution containing Super cool Z-1000 may improve the embryo survival rate. We recommend combined ice blocker usage to optimize the vitrification outcome. Copyright (c) 2010 Elsevier Ireland Ltd. All rights reserved.

Muusikamaailm : Suur klaveripidu Ruhrimaal. Kissingeni festival tippudega. Sulasoli 80. aastapäev. Richard Rodgers 100 / Priit Kuusk

Index Scriptorium Estoniae

Kuusk, Priit, 1938-

2002-01-01

6. juuni-17. augustini Ruhrimaal toimuvast klaverifestivalist. Bad Kissingenis toimuvatest suvepidustustest. Soome Lauljate ja Mängijate Liit tähistab asutamise 80. aastapäeva. Helilooja Richard Rodgersi sünnist möödub 100 aastat

JSD1000: multi-group cross section sets for shielding materials

International Nuclear Information System (INIS)

Yamano, Naoki

1984-03-01

A multi-group cross section library for shielding safety analysis has been produced by using ENDF/B-IV. The library consists of ultra-fine group cross sections, fine-group cross sections, secondary gamma-ray production cross sections and effective macroscopic cross sections for typical shielding materials. Temperature dependent data at 300, 560 and 900 K have been also provided. Angular distributions of the group to group transfer cross section are defined by a new method of ''Direct Angular Representation'' (DAR) instead of the method of finite Legendre expansion. The library designated JSD1000 are stored in a direct access data base named DATA-POOL and data manipulations are available by using the DATA-POOL access package. The 3824 neutron group data of the ultra-fine group cross sections and the 100 neutron, 20 photon group cross sections are applicable to shielding safety analyses of nuclear facilities. This report provides detailed specifications and the access method for the JSD1000 library. (author)

Evs. in Green Grid Era and climate change

Directory of Open Access Journals (Sweden)

F. -H. Li

2018-04-01

Full Text Available In this paper we set up foundations for vehicle dynamics and apply them to possible future EVs-wireless in-wheel motor elctric vehicles (wirelsee IWMEVs-in the coming green grid (GG era. GG is the most advanced form of the coming smart gird in which electricity is to be generated only through harmless resources, mainly solar energy. All the cars are to be EVs which are wirelessly connected to the GG through a regional aggregator which survey the area and in case of need, the emergency signal is to be sent to the vehicle to make a necessary action for collision avoiding. We also discuss the climate change in general and global warming in particular and state why global warming is a grave issue for the human being through archeo-climatology. We state a plausible waether-cycle conjecture of 1470 years as a combination of conjectures of H. Noshioka and the latest ones based on the Dansgaard-Oeschger (DO cycles.

42 CFR 1000.10 - General definitions.

Science.gov (United States)

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false General definitions. 1000.10 Section 1000.10 Public Health OFFICE OF INSPECTOR GENERAL-HEALTH CARE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL PROVISIONS INTRODUCTION; GENERAL DEFINITIONS Definitions § 1000.10 General definitions. In this chapter...

EV-A71 vaccine licensure: a first step for multivalent enterovirus vaccine to control HFMD and other severe diseases.

Science.gov (United States)

Mao, Qunying; Wang, Yiping; Bian, Lianlian; Xu, Miao; Liang, Zhenglun

2016-07-20

Enteroviruses (EVs) are the most common viral agents in humans. Although most infections are mild or asymptomatic, there is a wide spectrum of clinical manifestations that may be caused by EV infections with varying degrees of severity. Among these viruses, EV-A71 and coxsackievirus (CV) CV-A16 from group A EVs attract the most attention because they are responsible for hand, foot and mouth disease (HFMD). Other EV-A viruses such as CV-A6 and CV-A10 were also reported to cause HFMD outbreaks in several countries or regions. Group B EVs such as CV-B3, CV-B5 and echovirus 30 were reported to be the main pathogens responsible for myocarditis and encephalitis epidemics and were also detected in HFMD patients. Vaccines are the best tools to control infectious diseases. In December 2015, China's Food and Drug Administration approved two inactivated EV-A71 vaccines for preventing severe HFMD.The CV-A16 vaccine and the EV-A71-CV-A16 bivalent vaccine showed substantial efficacy against HFMD in pre-clinical animal models. Previously, research on EV-B group vaccines was mainly focused on CV-B3 vaccine development. Because the HFMD pathogen spectrum has changed, and the threat from EV-B virus-associated severe diseases has gradually increased, it is necessary to develop multivalent HFMD vaccines. This study summarizes the clinical symptoms of diseases caused by EVs, such as HFMD, myocarditis and encephalitis, and the related EV vaccine development progress. In conclusion, developing multivalent EV vaccines should be strongly recommended to prevent HFMD, myocarditis, encephalitis and other severe diseases.

Sparse interferometric millimeter-wave array for centimeter-level 100-m standoff imaging

Science.gov (United States)

Suen, Jonathan Y.; Lubin, Philip M.; Solomon, Steven L.; Ginn, Robert P.

2013-05-01

We present work on the development of a long range standoff concealed weapons detection system capable of imaging under very heavy clothing at distances exceeding 100 m with a cm resolution. The system is based off a combination of phased array technologies used in radio astronomy and SAR radar by using a coherent, multi-frequency reconstruction algorithm which can run at up to 1000 Hz frame rates and high SNR with a multi-tone transceiver. We show the flexible design space of our system as well as algorithm development, predicted system performance and impairments, and simulated reconstructed images. The system can be used for a variety of purposes including portal applications, crowd scanning and tactical situations. Additional uses include seeing through dust and fog.

Thermogravimetric analysis of silicon carbide-silicon nitride fibers at ambient to 1000 C in air

Science.gov (United States)

Daniels, J. G.; Ledbetter, F. E., III; Clemons, J. M.; Penn, B. G.

1984-01-01

Thermogravimetric analysis of silicon carbide-silicon nitride fibers was carried out at ambient to 1000 C in air. The weight loss over this temperature range was negligible. In addition, the oxidative stability at high temperature for a short period of time was determined. Fibers heated at 1000 C in air for fifteen minutes showed negligible weight loss (i.e., less than 1 percent).

Passivation kinetics of Mg-Nd-Gd-Zn-Zr (EV31A and Mg-Y-Nd-Gd-Zr (WE43C in NaOH solutions

Directory of Open Access Journals (Sweden)

Jakraphan Ninlachart

2017-09-01

Full Text Available Passivation kinetics of two Mg-RE alloys, such as Mg-Nd-Gd-Zn-Zr (EV31A, and Mg-Y-Nd-Gd-Zr (WE43C were investigated in two different heat treated conditions (solution treated and overaged in 0.01 - 1.0 M NaOH solutions under potentiostatic conditions. Negative reaction order was observed in dilute NaOH which transitioned to positive values as the passivation time increased and in the 1 M NaOH as well. The passive layers showed platelet morphology and the size of the platelets decreased with increase in the NaOH concentration. The hydrogen evolution reaction (HER kinetics was not improved on the passive layer covered surface of the Mg-RE alloys in contrast to the improvements reported on the hydroxide covered pure magnesium. The electrochemical impedance increased with increase in the NaOH concentration in the solution treated condition of both Mg-RE alloys, whereas the overaged EV31A alloy showed a reverse trend. The passive layer of EV31A showed almost 100% higher charge carrier density than the film formed on the WE43C in the overaged condition. A better passivation behavior was observed in the solution treated condition than that in the overaged condition which could be attributed to the uniform distribution of the RE elements in the solution treated specimens. The WE43C alloy revealed better corrosion resistance in the alkaline solution than the EV31A alloy.

Coordinated Control of PV Generation and EVs Charging Based on Improved DECell Algorithm

Directory of Open Access Journals (Sweden)

Guo Zhao

2015-01-01

Full Text Available Recently, the coordination of EVs’ charging and renewable energy has become a hot research all around the globe. Considering the requirements of EV owner and the influence of the PV output fluctuation on the power grid, a three-objective optimization model was established by controlling the EVs charging power during charging process. By integrating the meshing method into differential evolution cellular (DECell genetic algorithm, an improved differential evolution cellular (IDECell genetic algorithm was presented to solve the multiobjective optimization model. Compared to the NSGA-II and DECell, the IDECell algorithm showed better performance in the convergence and uniform distribution. Furthermore, the IDECell algorithm was applied to obtain the Pareto front of nondominated solutions. Followed by the normalized sorting of the nondominated solutions, the optimal solution was chosen to arrive at the optimized coordinated control strategy of PV generation and EVs charging. Compared to typical charging pattern, the optimized charging pattern could reduce the fluctuations of PV generation output power, satisfy the demand of EVs charging quantity, and save the total charging cost.

7 CFR 1000.6 - Supply plant.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1000.6 Section 1000.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Definitions § 1000.6 Supply plant. Supply plant means a plant approved by a duly constituted regulatory agency...

12 CFR 611.1000 - General authority.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false General authority. 611.1000 Section 611.1000 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM ORGANIZATION Bank Mergers, Consolidations and Charter Amendments § 611.1000 General authority. (a) An amendment to a bank charter may relate...

An Ultrasensitive Electrochemical Immunosensor for HIV p24 Based on Fe3O4@SiO2 Nanomagnetic Probes and Nanogold Colloid-Labeled Enzyme–Antibody Copolymer as Signal Tag

Directory of Open Access Journals (Sweden)

Tianhua Li

2013-03-01

Full Text Available An ultrasensitive portable electrochemical immunosensor for human immunodeficiency virus p24 (HIV p24 antigen detection has been developed, whereby the detection sensitivity was 1000 times higher than that of the ELISA method. Firstly, a novel HRP enzyme–antibody copolymer (EV-p24 Ab2 was synthesized through an EnVision regent (EV, a dextrin amine skeleton anchoring more than 100 molecules of HRP and 15 molecules of anti IgG, then incubated in the secondary antibody of p24. Secondly, the copolymer was immobilized on the gold nanocolloids (AuNPs to fabricate a novel signal tag (AuNPs/EV-p24 Ab2. Subsequently, a sandwich-type immunoreaction would take place between the capture probe (silicon dioxide-coated magnetic Fe3O4 nanoparticles (MNPs labeled with the primary p24 antibody (MNPs-p24 Ab1, p24 (different concentrations and the signal tag [AuNPs/EV-p24 Ab2] to form the immunocomplex. Finally, the immunocomplex was absorbed on the surface of screen printed carbon electrode (SPCE by a magnet and immersed in the o-hydroxyl phenol (HQ and H2O2. The large amounts of HRP on the signal tag can catalyze the oxidation of HQ by H2O2, which can induce an amplified reductive current. Moreover, the capture probe could improve the accumulation ability of p24 and facilitate its separation from the substrate through the magnet. Under optimal conditions, the proposed immunoassay exhibited good sensitivity to p24 within a certain concentration range from 0.001 to 10.00 ng/mL, with a detection limit of 0.5 pg/mL (S/N = 3. The proposed method can be used for real-time and early detection of HIV-infected people.

Markets Share Models for EVs

DEFF Research Database (Denmark)

Jensen, Thomas Christian; Christensen, Linda

for the transport sector is announced to be a reduction of greenhouse gas emissions by 20% in 2020 compared to 2005. It is the plan to obtain part of this reduction through the EU targets of 10% renewable energy by 2020 in surface transport and a requirement for EU car producers to lower average CO2 emissions from...... to the end of 2015. More ambitious greenhouse gas reductions are announced and EV’s may contrib-ute to such targets. However, no specific target has been set for the share of electric vehicles. In order to investigate the potential role of electric vehicles (EVs), DTU transport has construct-ed a small car...

Coordination of EVs Participation for Load Frequency Control in Isolated Microgrids

DEFF Research Database (Denmark)

Vahedipour-Dahraie, Mostafa; Rashidizaheh-Kermani, Homa; Najafi, Hamid Reza

2017-01-01

Increasing the penetration levels of renewable energy sources (RESs) in microgrids (MGs) may lead to frequency instability issues due to intermittent nature of RESs and low inertia of MG generating units. On the other hand, presence of electric vehicles (EVs), as new high-electricity- consuming...... appliances, can be a good opportunity to contribute in mitigating the frequency deviations and help the system stability. This paper proposes an optimal charging/discharging scheduling of EVs with the goal of improving frequency stability of MG during autonomous operating condition. To this end, an efficient...

Effects of Adopol EVS-9279X on the emulsion and film properties of ...

African Journals Online (AJOL)

The effects of Adopol EVS-9279X on the emulsion and film properties of emulsion paint were investigated using 5% - 10% w/w sample formulations. Results indicate that Adopol EVS-9279X did not alter the apparent viscosities of the emulsion paint samples. It was found to have lowered the specific gravity from 1.53 to 1.47 ...

AP1000, a nuclear central of advanced design; AP1000, una central nuclear de diseno avanzado

Energy Technology Data Exchange (ETDEWEB)

Hernandez M, N.; Viais J, J. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: nhm@nuclear.inin.mx

2005-07-01

The AP1000 is a design of a nuclear reactor of pressurized water (PWR) of 1000 M We with characteristic of safety in a passive way; besides presenting simplifications in the systems of the plant, the construction, the maintenance and the safety, the AP1000 is a design that uses technology endorsed by those but of 30 years of operational experience of the PWR reactors. The program AP1000 of Westinghouse is focused to the implementation of the plant to provide improvements in the economy of the same one and it is a design that is derived directly of the AP600 designs. On September 13, 2004 the US-NRC (for their initials in United States- Nuclear Regulatory Commission) approved the final design of the AP1000, now Westinghouse and the US-NRC are working on the whole in a complete program for the certification. (Author)

Technology Roadmaps - Electric and plug-in hybrid electric vehicles (EV/PHEV)

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-06-15

The mass deployment of electric and plug-in hybrid electric vehicles (EVs and PHEVs) that rely on low greenhouse gas (GHG) emission electricity generation has great potential to significantly reduce the consumption of petroleum and other high CO2-emitting transportation fuels. The vision of the Electric and Plug-in Hybrid (EV/PHEV) Vehicles Roadmap is to achieve by 2050 the widespread adoption and use of EVs and PHEVs, which together represent more than 50% of annual LDV (light duty vehicle) sales worldwide. In addition to establishing a vision, this roadmap sets strategic goals to achieve it, and identifies the steps that need to be taken to accomplish these goals. This roadmap also outlines the roles and collaboration opportunities for different stakeholders and shows how government policy can support the overall achievement of the vision. The strategic goals for attaining the widespread adoption and use of EVs and PHEVs worldwide by 2050 cover the development of the EV/PHEV market worldwide through 2030 and involve targets that align with global targets to stabilise GHG concentrations. These technology-specific goals include the following: Set targets for electric-drive vehicle sales; Develop coordinated strategies to support the market introduction of electric-drive vehicles; Improve industry understanding of consumer needs and behaviours; Develop performance metrics for characterising vehicles; Foster energy storage RD and D initiatives to reduce costs and address resource-related issues; and, Develop and implement recharging infrastructure. The roadmap outlines additional recommendations that must be considered in order to successfully meet the technology milestones and strategic goals. These recommendations include the following: Use a comprehensive mix of policies that provide a clear framework and balance stakeholder interests; Engage in international collaboration efforts; and, Address policy and industry needs at a national level. The IEA will work in an

21 CFR 589.1000 - Gentian violet.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Gentian violet. 589.1000 Section 589.1000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS... Substances Prohibited From Use in Animal Food or Feed § 589.1000 Gentian violet. The Food and Drug...

United States National Grid for New Mexico, UTM 12, (1000m X 1000m polygons )

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This is a polygon feature data layer of United States National Grid (1000m x 1000m polygons ) constructed by the Center for Interdisciplinary Geospatial Information...

United States National Grid for New Mexico, UTM 13, (1000m X 1000m polygons )

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This is a polygon feature data layer of United States National Grid (1000m x 1000m polygons ) constructed by the Center for Interdisciplinary Geospatial Information...

Low energy spread 100 MeV-1 GeV electron bunches from laser wakefield acceleration at LOASIS

International Nuclear Information System (INIS)

Geddes, C.G.R.; Esarey, E.; Michel, P.; Nagler, B.; Nakamura, K.; Plateau, G.R.; Schroeder, C.B.; Shadwick, B.A.; Toth, Cs.; Van Tilborg, J.; Leemans, W.P.; Hooker, S.M.; Gonsalves, A.J.; Michel, E.; Cary, J.R.; Bruhwiler, D.

2006-01-01

Experiments at the LOASIS laboratory of LBNL recently demonstrated production of 100 MeV electron beams with low energy spread and low divergence from laser wakefield acceleration. The radiation pressure of a 10 TW laser pulse guided over 10 diffraction ranges by a plasma density channel was used to drive an intense plasma wave (wakefield), producing acceleration gradients on the order of 100 GV/m in a mm-scale channel. Beam energy has now been increased from 100 to 1000 MeV by using a cm-scale guiding channel at lower density, driven by a 40TW laser, demonstrating the anticipated scaling to higher beam energies. Particle simulations indicate that the low energy spread beams were produced from self trapped electrons through the interplay of trapping, loading, and dephasing. Other experiments and simulations are also underway to control injection of particles into the wake, and hence improve beam quality and stability further

Energy deposition model for low-energy electrons (10-10 000 eV) in air

International Nuclear Information System (INIS)

Roldan, A.; Perez, J.M.; Williart, A.; Blanco, F.; Garcia, G.

2004-01-01

An energy deposition model for electrons in air that can be useful in microdosimetric applications is presented in this study. The model is based on a Monte Carlo simulation of the single electron scattering processes that can take place with the molecular constituents of the air in the energy range 10-10 000 eV. The input parameters for this procedure have been the electron scattering cross sections, both differential and integral. These parameters were calculated using a model potential method which describes the electron scattering with the molecular constituent of air. The reliability of the calculated integral cross section values has been evaluated by comparison with direct total electron scattering cross-section measurements performed by us in a transmission beam experiment. Experimental energy loss spectra for electrons in air have been used as probability distribution functions to define the electron energy loss in single collision events. The resulting model has been applied to simulate the electron transport through a gas cell containing air at different pressures and the results have been compared with those observed in the experiments. Finally, as an example of its applicability to dosimetric issues, the energy deposition of 10 000 eV by means of successive collisions in a free air chamber has been simulated

A high resolution EELS study of free-carrier variations in H2+/H+ bombarded (100)GaAs

International Nuclear Information System (INIS)

Dubois, L.H.; Schwartz, G.P.

1984-01-01

High resolution electron energy loss spectroscopy (EELS) has been used to examine whether thermal recovery of the near-surface free-carrier concentration in Te-doped (100) GaAs is accomplished following low energy (250--1500 eV) hydrogen ion bombardment. For hydrogen ion impact energies below 500 eV, the nominal bulk free-carrier density is recovered by annealing at 725 K for 2 h. For comparable ion doses, the net free-carrier concentration decreases monotonically at higher impact energies under similar annealing conditions. The threshold for damage retention occurs close to the value of transmitted energy which is necessary to create either a Ga or an As interstitial point defect

The Belgian initiative G1000. A feasible model of deliberative cyber democracy

Directory of Open Access Journals (Sweden)

Laura Tejedor Fuentes

2016-11-01

Full Text Available In 2010, after five hundred days without any stable form of government, a group of Belgian citizens from a wide range of social backgrounds launched a citizenship summit called 'G1000'. The aim of the event was to create citizen involvement in politics by stimulating participants to take part in debates about social issues and by applying innovative techniques of deliberative democracy. In order to verify whether the model mentioned meets the criteria of an “online democratic-deliberative” experiment, this article carried out a quantitative analysis of the G1000 based on the work of Fishkin, Chadwick and Habermas. According to the majority of authors who have contributed to the topic, including the spokesperson and organizer of the event, Vincent Jacquet the results demonstrate that the G1000 summit is, in fact, a genuine democratic-deliberative initiative.

A win-win marginal rent analysis for operator and consumer under battery leasing mode in China electric vehicle market

International Nuclear Information System (INIS)

Li Zhe; Ouyang Minggao

2011-01-01

Recently battery leasing has been introduced into the market by automobile manufacturers and power suppliers due to its potential to reduce the purchase cost of electric vehicles (EVs). However, the profit prospect of battery leasing is still uncertain. This paper takes the views of both the operators and consumers and calculates the 'win-win' marginal rent, which not only ensures the profitability of operators, but also allows consumers a lower expenditure than using Internal combustion engine vehicles (ICVs) and EVs with embedded batteries. Battery cost, vehicle weight, gasoline and electricity price, and the discount rate have impacts on the rent. Battery cost plays a dominant role and a battery cost >5 Yen /W h fails to enable the survival of battery leasing to all types of EVs. Battery leasing would be more competitive when focusing on heavier EVs. At least one of the three thresholds is required for the existence of rent pricing range for a 1000 kg EV: gasoline retail price >6 Yen /L, electricity price <0.6 Yen /kW h, or the discount rate <7%. Typically, the feasible battery rent range is 0.34-0.38 Yen /W h/year for a 1000 kg EV under the present battery cost 2 Yen /W h and China current gasoline and electricity prices. - Highlights: → Rent pricing for EV battery leasing must obey win-win rule for BLO and consumers. → Rent is affected by battery cost, vehicle weight, energy price and discount rate. → Battery cost plays dominant role for the BLO survival as described in '5-3-2' Law. → Heavier EVs are more suitable for battery leasing when battery cost is high. → The profitability of BLO is sensitive to the price of gasoline and electricity.

Study of an individual neutron dosimeter

International Nuclear Information System (INIS)

Debeauvais, M.; Tripier, J.

1976-01-01

A dosimeter using Kodak LR 115 cellulose nitrate as detecting material was designed. It serves to determine 3 neutron energy ranges. The 6 Li(n,α)t reaction is used for the thermal region, the sensitivity being 0.2mrads to 1 rad for neutron energies between thermal and 0.05eV. The same reaction defines the 0.05eV to 1000eV energy range but the detection system is placed inside a cadmium screen; the sensitivity is 0.2 to 500rads. Finally above 1MeV the neutron reactions used are those on the detector components themselves, i.e. elastic collisions and (nα) reactions on carbon, nitrogen and oxygen nuclei. Detection is possible between 0.7 and 700 rads [fr

Westinghouse AP 1000 program status

International Nuclear Information System (INIS)

Doehnert, B.

2002-01-01

The project 1000 is presented and features are discussed in the paper. Design maturity is characterized by 1300 man-year / $400 million design and testing effort, more than 12 000 design documents completed; 3D computer model developed. It includes structures, equipment, small / large pipe, cable trays, ducts etc. Licensing Maturity is determined by a very thorough and complete NRC review of AP600; 110 man-year effort (NRC) over 6 years, $30 million; independent, confirmatory plant analysis; independent, confirmatory plant testing (ROSA, OSU); over 7400 questions answered, no open items; over 380 meeting with NRC, 43 meetings with ACRS. NRC Design Certification is issued in December 1999. Reasons for developing AP 1000 and design changes are presented. Economic analysis shows an expectation for payback within 20 years. AP1000 provides 75% power uprate for 15% increment in capital cost. AP1000 meets new plant economic targets in the near term

Electronic excitation to low-lying states of GeF4 molecule by electron impact: A comparative study with CF4 and SiF4 molecules

International Nuclear Information System (INIS)

Ohtomi, S; Matsui, M; Mochizuki, Y; Suga, A; Kato, H; Hoshino, M; Tanaka, H; Duflot, D; Limão-Vieira, P

2015-01-01

We report on the measurements of the electron impact electronic excitation cross sections for XF 4 (X = C, Si and Ge) molecules at 100 eV, 5° scattering angle and 30 eV, 30° in the electron energy loss range 8.0 - 18 eV. For a target of GeF 4 molecule, the optically-forbidden behavior has been observed in the lower electron energy loss range. (paper)

Experimental studies of fundamental aspects of Auger emission process in Cu(100) and Ag(100)

Science.gov (United States)

Joglekar, Prasad Vivek

Auger spectra at the low energies are accompanied by large contributions unrelated to the Auger transition. The Auger unrelated contributions can obscure the Auger peak and affect the quantitative analysis of the materials under investigation. In this dissertation we present a methodology to measure experimentally the Auger unrelated contributions and eliminate it from the Auger spectrum for obtaining an Auger spectrum inherent to the Auger transition. We used Auger Photoelectron Coincidence Spectroscopy (APECS) to obtain the Auger spectrum. APECS measures the Auger spectrum in coincidence with the core energy level and thus discriminating the contributions arising from secondary electrons and electrons arising from the non-Auger transition. Although APECS removes most of the Auger unrelated contributions, it cannot distinguish the contribution which is measured in coincidence with the inelastically scattered valence band electrons emitted at the core energy. To measure this inelastically scattered valence band contribution we did a series of measurements on Ag(100) to study NVV Auger spectrum in coincidence with 4p energy level and Cu(100) to study MVV Auger spectrum in coincidence with 3p energy level. The coincidence detection of the core and Auger-valence electrons was achieved by the two cylindrical mirror analyzers (CMAs). One CMA was fixed over a range of energies in between VB and core energy level while other CMA scanned corresponding low energy electrons from 0 to70eV. The spectrums measured were fit to a parameterized function which was extrapolated to get an estimate of inelastically scattered valence band electrons. The estimated contribution was subtracted for the Ag and Cu APECS spectrum to obtain a spectrum solely due to Auger transition with inelastically scattered Auger electron and multi Auger decay contributions associated with the transition. In the latter part of this dissertation, we propose a theoretical model based on the spectral intensity

Alignment and orientation of the 21P state of helium by electron impact at 29.6 and 51.2 eV

International Nuclear Information System (INIS)

McAdams, R.; Hollywood, M.T.; Crowe, A.; Williams, J.F.

1980-01-01

The electron-photon coincidence technique has been used to deduce the lambda and chi parameters for excitation of the 2 1 P state of helium by electron impact at 29.6 and 51.2 eV incident energies and for electron scattering angles in the range 15 to 130 0 . The lambda parameter shows a minimum at small and large scattering angles. When combined with the data of Hollywood et al (J. Phys. B.; 12:819 (1979)) at 81.2 eV, it can be seen that as the incident energy decreases, the depth of the low-angle minimum decreases and its position moves to larger scattering angles. In contrast, the depth of the second minimum increases with decreasing incident electron energy. The experimental values of lambda and chi are compared with values predicted from the first Born approximation, a distorted-wave polarised-orbital approximation, a first-order many-body theory and an R-matrix theory. None of the theoretical values is in agreement with the measured data although the R-matrix calculation gives a reasonable indication of the features of both lambda and chi at 29.6 eV. (author)

AP1000{sup TM} plant modularization

Energy Technology Data Exchange (ETDEWEB)

Cantarero L, C.; Demetri, K. J. [Westinghouse Electric Co., 1000 Westinghouse Drive, Cranberry Township, PA 16066 (United States); Quintero C, F. P., E-mail: cantarc@westinghouse.com [Westinghouse Electric Spain, Padilla 17, 28006 Madrid (Spain)

2016-09-15

The AP1000{sup TM} plant is an 1100 M We pressurized water reactor (PWR) with passive safety features and extensive plant simplifications that enhance construction, operation, maintenance and safety. Modules are used extensively in the design of the AP1000 plant nuclear island. The AP1000 plant uses modern, modular-construction techniques for plant construction. The design incorporates vendor-designed skids and equipment packages, as well as large, multi-ton structural modules and special equipment modules. Modularization allows traditionally sequential construction tasks to be completed simultaneously. Factory-built modules can be installed at the site in a planned construction schedule. The modularized AP1000 plant allows many more construction activities to proceed in parallel. This reduces plant construction calendar time, thus lowering the costs of plant financing. Furthermore, performing less work onsite significantly reduces the amount of skilled field-craft labor, which costs more than shop labor. In addition to labor cost savings, doing more welding and fabrication in a factory environment raises the quality of work, allowing more scheduling flexibility and reducing the amount of specialized tools required onsite. The site layout for the AP1000 plant has been established to support modular construction and efficient operations during construction. The plant layout is compact, using less space than previous conventional plant layouts. This paper provides and overview of the AP1000 plant modules with an emphasis on structural modules. Currently the Westinghouse AP1000 plant has four units under construction in China and four units under construction in the United States. All have shown successful fabrication and installation of various AP1000 plant modules. (Author)

AP1000"T"M plant modularization

International Nuclear Information System (INIS)

Cantarero L, C.; Demetri, K. J.; Quintero C, F. P.

2016-09-01

The AP1000"T"M plant is an 1100 M We pressurized water reactor (PWR) with passive safety features and extensive plant simplifications that enhance construction, operation, maintenance and safety. Modules are used extensively in the design of the AP1000 plant nuclear island. The AP1000 plant uses modern, modular-construction techniques for plant construction. The design incorporates vendor-designed skids and equipment packages, as well as large, multi-ton structural modules and special equipment modules. Modularization allows traditionally sequential construction tasks to be completed simultaneously. Factory-built modules can be installed at the site in a planned construction schedule. The modularized AP1000 plant allows many more construction activities to proceed in parallel. This reduces plant construction calendar time, thus lowering the costs of plant financing. Furthermore, performing less work onsite significantly reduces the amount of skilled field-craft labor, which costs more than shop labor. In addition to labor cost savings, doing more welding and fabrication in a factory environment raises the quality of work, allowing more scheduling flexibility and reducing the amount of specialized tools required onsite. The site layout for the AP1000 plant has been established to support modular construction and efficient operations during construction. The plant layout is compact, using less space than previous conventional plant layouts. This paper provides and overview of the AP1000 plant modules with an emphasis on structural modules. Currently the Westinghouse AP1000 plant has four units under construction in China and four units under construction in the United States. All have shown successful fabrication and installation of various AP1000 plant modules. (Author)

Alignment of 1000 Genomes Project reads to reference assembly GRCh38.

Science.gov (United States)

Zheng-Bradley, Xiangqun; Streeter, Ian; Fairley, Susan; Richardson, David; Clarke, Laura; Flicek, Paul

2017-07-01

The 1000 Genomes Project produced more than 100 trillion basepairs of short read sequence from more than 2600 samples in 26 populations over a period of five years. In its final phase, the project released over 85 million genotyped and phased variants on human reference genome assembly GRCh37. An updated reference assembly, GRCh38, was released in late 2013, but there was insufficient time for the final phase of the project analysis to change to the new assembly. Although it is possible to lift the coordinates of the 1000 Genomes Project variants to the new assembly, this is a potentially error-prone process as coordinate remapping is most appropriate only for non-repetitive regions of the genome and those that did not see significant change between the two assemblies. It will also miss variants in any region that was newly added to GRCh38. Thus, to produce the highest quality variants and genotypes on GRCh38, the best strategy is to realign the reads and recall the variants based on the new alignment. As the first step of variant calling for the 1000 Genomes Project data, we have finished remapping all of the 1000 Genomes sequence reads to GRCh38 with alternative scaffold-aware BWA-MEM. The resulting alignments are available as CRAM, a reference-based sequence compression format. The data have been released on our FTP site and are also available from European Nucleotide Archive to facilitate researchers discovering variants on the primary sequences and alternative contigs of GRCh38. © The Authors 2017. Published by Oxford University Press.

Effect of a Stepped Si(100) Surface on the Nucleation Process of Ge Islands

Science.gov (United States)

Yesin, M. Yu.; Nikiforov, A. I.; Timofeev, V. A.; Mashanov, V. I.; Tuktamyshev, A. R.; Loshkarev, I. D.; Pchelyakov, O. P.

2018-03-01

Nucleation of Ge islands on a stepped Si(100) surface is studied. It is shown by diffraction of fast electrons that at a temperature of 600°C, constant flux of Si, and deposition rate of 0.652 Å/s, a series of the 1×2 superstructure reflections completely disappears, if the Si (100) substrate deviated by an angle of 0.35° to the (111) face is preliminarily heated to 1000°C. The disappearance of the 1×2 superstructure reflexes is due to the transition from the surface with monoatomic steps to that with diatomic ones. Investigations of the Ge islands' growth were carried out on the Si(100) surface preliminarily annealed at temperatures of 800 and 1000°C. It is shown that the islands tend to nucleate at the step edges.

Sõlmornamendist, eriti muinaskäevõrudel ja setu naiste ülerõivastel / Mare Piho

Index Scriptorium Estoniae

Piho, Mare, 1944-

2006-01-01

Artikli ajendiks sai 1972. aastal Setumaalt juhuleiuna saadud 11. sajandi käevõru. Käevõrul kujutaud plettornamenti on kasutatud setu naiste 19. sajandi keskpaiga - 20. sajandi riietelel. Sõlmest kui märgist ja selle tähendusest. Sõlmornamendist setu naiste pealisriietel. Sõlmornamendi järjepidevusest ja püsimisest

Determination of resonance parameters at 4.90 eV for Au 197

International Nuclear Information System (INIS)

Tellier, Henry; Alix, Michel

1969-12-01

A new study of the 4.9 eV resonance of gold was carried out by the time of flight method using the 45 MeV Saclay linac as a pulsed neutron source. Four sample thicknesses were used for the measurements. The four transmission curves were shaped analysed and the following parameters were obtained: E = 4.900 ± 0.005 eV - Γ = 137.5 ± 2.0 meV and Γ n = 15.0 ± 0.2 meV. (author) [fr

Effects of the electron beam on InP(100)

International Nuclear Information System (INIS)

Bouslama, M.; Jardin, C.; Ghamnia, M.

1996-01-01

Auger Electron Spectroscopy (AES) is performed to monitor the InP(100) surface evolution while it is irradiated by an electron beam of 5 KeV energy and 10 -3 A.cm -2 current density. A charge phenomenon appears during the irradiation of sputter-cleaned InP(100) by Ar + at low energy (500 eV). The deposition of phosphorus or antimony at room temperature on cleaned InP(100) is a good way of preventing this charging problem. This is also achieved by the growth of stoichiometric indium phosphide on InP(100) substrate, from an injection of phosphine and indium trimethyl whose ratio V/III is of 50, in a MOCVD (Metal Organic Chemical Vapor Deposition) reactor. The electron beam even acts to stimulate oxidation of the stoichiometric InP(100) surface involving on the top layers, into a well defined oxide such as InPO 4 or a contamination layer composed of carbon and oxygen. The partial pressure in the spectrometer is about 10 -9 Torr. The incident electrons produce breaking of (In-P) chemical bonds so that the resulting indium takes part in the oxidation process. The phosphorus is thought to be desorbed from the surface. (author)

Changes in the EV-A71 Genome through Recombination and Spontaneous Mutations: Impact on Virulence

Directory of Open Access Journals (Sweden)

Madiiha Bibi Mandary

2018-06-01

Full Text Available Enterovirus 71 (EV-A71 is a major etiological agent of hand, foot and mouth disease (HFMD that mainly affects young children less than five years old. The onset of severe HFMD is due to neurological complications bringing about acute flaccid paralysis and pulmonary oedema. In this review, we address how genetic events such as recombination and spontaneous mutations could change the genomic organization of EV-A71, leading to an impact on viral virulence. An understanding of the recombination mechanism of the poliovirus and non-polio enteroviruses will provide further evidence of the emergence of novel strains responsible for fatal HFMD outbreaks. We aim to see if the virulence of EV-A71 is contributed solely by the presence of fatal strains or is due to the co-operation of quasispecies within a viral population. The phenomenon of quasispecies within the poliovirus is discussed to reflect viral fitness, virulence and its implications for EV-A71. Ultimately, this review gives an insight into the evolution patterns of EV-A71 by looking into its recombination history and how spontaneous mutations would affect its virulence.

UV photon and low-energy (5--150 eV) electron-stimulated processes at environmental interfaces

International Nuclear Information System (INIS)

Orlando, T.M.

1997-01-01

Irradiation of surfaces and interfaces with low-energy (5--150 eV) electrons and ultraviolet photons occurs during the storage of ''mixed'' (chemical/radioactive) waste forms and during processing steps which involve the use of low temperature plasmas. It is well known that electron- and photon-stimulated desorption (ESD and PSD) from wide band-gap materials and interfaces can be initiated by Auger decay of deep valence and shallow core holes. This process consists of hole production, Auger decay, reversal of the Madelung potential, and ion expulsion due to the Coulomb repulsion. ESD and PSD of neutrals also occurs and involves production of electron-hole pairs and excitons. Generally, neutral yields dominate ESD and PSD cross sections, which typically vary between ∼10 -16 and 10 -22 cm 2 . The authors present results on the ESD and PSD of environmentally relevant substrates such as ZrO 2 (100), soda-glass, and NaNO 3 . The major cation thresholds and yields indicate that ESD and PSD from these complex materials involves Auger stimulated events. In particular, desorption thresholds correlate with ionization of the O(2s), Zr(4p), Si(2p) and Na(2s) levels. The near band-gap threshold energy (∼5--7 eV) for the desorption of neutrals (i.e., atomic oxygen, NO, etc) demonstrate the overall importance of self-trapped and localized excitons in both ESD and PSD of typical ceramics and oxides

Generation of live offspring from vitrified embryos with synthetic polymers SuperCool X-1000 and SuperCool Z-1000.

Science.gov (United States)

Marco-Jimenez, F; Jimenez-Trigos, E; Lavara, R; Vicente, J S

2014-01-01

Ice growth and recrystallisation are considered important factors in determining vitrification outcomes. Synthetic polymers inhibit ice formation during cooling or warming of the vitrification process. The aim of this study was to assess the effect of adding commercially available synthetic polymers SuperCool X-1000 and SuperCool Z-1000 to vitrification media on in vivo development competence of rabbit embryos. Four hundred and thirty morphologically normal embryos recovered at 72 h of gestation were used. The vitrification media contained 20% dimethyl sulphoxide and 20% ethylene glycol, either alone or in combination with 1% of SuperCool X-1000 and 1% SuperCool. Our results show that embryos can be successfully vitrified using SuperCool X-1000 and SuperCool Z-1000 and when embryos are transferred, live offspring can be successfully produced. In conclusion, our results demonstrated that we succeeded for the first time in obtaining live offspring after vitrification of embryos using SuperCool X-1000 and SuperCool Z-1000 polymers.

Electron capture in slow collisions of multicharged ions with hydrogen atoms using merged beams

International Nuclear Information System (INIS)

Havener, C.C.; Nesnidal, M.P.; Porter, M.R.; Phaneuf, R.A.

1991-01-01

Absolute total electron-capture cross-section mesurements are reported for collisions of O 3+ and O 4+ with atomic hydrogen in the energy range 1-1000 eV /amu using merged beams. The data are compared with available coupled-states theoretical calculations. (orig.)

E/V Nautilus Detection of Isolated Features in the Eastern Pacific Ocean: Newly Discovered Calderas and Methane Seeps

Science.gov (United States)

Raineault, N.; Irish, O.; Lubetkin, M.

2016-02-01

The E/V Nautilus mapped over 80,000 km2 of the seafloor in the Gulf of Mexico and Eastern Pacific Ocean during its 2015 expedition. The Nautilus used its Kongsberg EM302 multibeam system to map the seafloor prior to remotely operated vehicle (ROV) dives, both for scientific purposes (site selection) and navigational safety. The Nautilus also routinely maps during transits to identify previously un-mapped or unresolved seafloor features. During its transit from the Galapagos Islands to the California Borderland, the Nautilus mapped 44,695 km2 of seafloor. Isolated features on the seafloor and in the water-column, such as calderas and methane seeps, were detected during this data collection effort. Operating at a frequency of 30 kHz in waters ranging from 1000-5500 m, we discovered caldera features off the coast of Central America. Since seamounts are known hotspots of biodiversity, locating new ones may enrich our understanding of seamounts as "stepping stones" for species distribution and ocean current pathways. Satellite altimetry datasets prior to this data either did not discern these calderas or recognized the presence of a bathymetric high without great detail. This new multibeam bathymetry data, gridded at 50 m, gives a precise look at these seamounts that range in elevation from 350 to 1400 m from abyssal depth. The largest of the calderas is circular in shape and is 10,000 m in length and 5,000 m in width, with a distinct circular depression at the center of its highest point, 1,400 m above the surrounding abyssal depth. In the California Borderland region, located between San Diego and Los Angeles, four new seeps were discovered in water depths from 400-1,020 m. ROV exploration of these seeps revealed vent communities. Altogether, these discoveries reinforce how little we know about the global ocean, indicate the presence of isolated deep-sea ecosystems that support biologically diverse communities, and will impact our understanding of seafloor habitat.

Observations of several disruptions in PLT using soft and ultra-soft x-ray radiation

International Nuclear Information System (INIS)

Eames, D.R.; von Goeler, S.; Sauthoff, N.R.; Stodiek, W.

1979-03-01

The evolution of ultra-soft x-ray radiation (USX, hν approx. > 100 eV) is compared to that of the soft x-ray radiation (SX, hν approx. > 1000 eV) during several disruptions in PLT. Spatial resolution is obtained in both cases by arrays of silicon surface barrier detectors viewing along different chords. During some disruptions the USX behaves quite differently from the SX, and a classification is made based on the USX behavior. Different interpretations of the data are discussed, along with the possibility that these measurements may distinguish between the roles of temperature and impurity density changes during disruptions

Performance tests of a 2-meter grasshopper monochromator at photon factory

International Nuclear Information System (INIS)

Yanagihara, Mihiro; Maezawa, Hideki; Sasaki, Taizo; Suzuki, Yoshio; Iguchi, Yasuo.

1984-12-01

A 2-meter grasshopper monochromator was installed and adjusted at BL-11A in Photon Factory, and performance tests were carried out. The usable photon energy range for the monochromator is 90 to 1000 eV for a 2400 grooves/mm grating, and the flux is 10 8 - 10 9 photons/sec for entrance and exit slit widths of 15 μm. A resolving power of about 2000 is realized at 250 eV for this slit width. (author)

VVER-1000 small-medium break LOCAs predictions by ASTEC

International Nuclear Information System (INIS)

Georgieva, J.; Stefanova, A.; Atanasova, B.; Groudev, P.; Tusheva, P.; Mladenov, I.; Dimov, D.; Passalacqua, R.

2005-01-01

This paper deals with an assessment of ASTEC1.1v0 code in the simulation of small and medium break LOCAs (ranging from 30mm up to 70mm equivalent diameter). The reference power plant for this analysis is a VVER-1000/V320 (e.g. Units 5 and 6 at Kozloduy NPP). A preliminary comparison with MELCOR and RELAP-SCDAP severe accident codes will be discussed. This investigation has been performed in the framework of the SARNET project (under the Euratom 6 th framework program) by the FoBAUs group (Forum of Bulgarian ASTEC users). The FoBAUs group aims at the validation of the ASTEC code in the field of severe accidents. Future activities will target the ASTEC capability (as a PSA-level 2 tool) to simulate a large range of reactor accident scenarios with intervention of safety systems (either passive systems or operated by operators). The final target is to assess Severe Accident Management (SAM) procedures for VVER-1000 reactors. The ASTEC1.1v0 code version here used is the one released in June 2004 by the French IRSN (Institut de Radioprotection et de Surete Nucleaire) and the German GRS (Gesellschaft ReactorSicherheit mbH). (author)

Weakly-bound adsorption states and low-temperature adsorption kinetiks of oxygen on tungsten (100) and (110) faces

International Nuclear Information System (INIS)

Zhukov, V.V.; Osovskij, V.D.; Ptushnikov, Yu.G.; Sukretnyj, V.G.; Chujkov, B.A.

1986-01-01

A molecular beam technique with an effusion source operating at T=200 K is used to study the adsorption interaction of oxygen with W(100) and (110) faces in the range of the simple temperatures from 5 to 340 K. Three weakly-bound adsorption states of oxygen are detected corresponding to adsorption in the second, third and forth monolayer. These states are characterized by adsorption energies of 0.13, 0.08 and 0.07 eV and desorption temperatures of 45, 27 and 25 K, respectively. The kinetics of filling of these states is almost similar for both faces, whereas the adsorption kinetics in the first monolayer is essentially different. A dissociative nature of adsorption at T >or approx. 5 K and a jump migration mechanism of the admolecules in the precursor state to the stationary adsorption sites are suggested

Effect of on-site Coulomb interaction on electronic and transport properties of 100% spin polarized CoMnVAs

Energy Technology Data Exchange (ETDEWEB)

Bhat, Tahir Mohiuddin; Gupta, Dinesh C., E-mail: sosfizix@gmail.com

2017-08-01

Highlights: • 100% spin-polarized material important for the application in spintronics. • Ferromagnetic nature. • Ductile in nature for mechanical applications. • Semiconducting behavior with a band gap of 0.55 eV in minority spin channel. • Possibly efficient thermoelectric material. - Abstract: The structural, electronic, magnetic and transport properties of a new quaternary Heusler alloy CoMnVAs have been investigated by employing generalized gradient approximation (GGA), modified Becke-Johnson (mBJ) and GGA with Hubbard U correction (GGA + U). The alloy is energetically more stable in ferromagnetic Y{sub 1} type structure. Elastic parameters reveal high anisotropy and ductile nature of the material. CoMnVAs shows half-metallic ferromagnet character with 100% spin polarization at Fermi level with band gap of 0.55 eV in the minority spin state. The alloy also possesses high electrical conductivity and Seebeck coefficients with 15 μVK{sup −1} at room temperature, achieving a figure of merit of 0.65 at high temperatures. The high degree of ductility, 100% spin polarization and large Seebeck coefficient, makes it an attractive candidate to be used in spin voltage generators and thermoelectric materials.

A Method for Remote Control of EV Charging by Modifying IEC61851 Compliant EVSE Based PWM Signal

DEFF Research Database (Denmark)

Pedersen, Anders Bro; Martinenas, Sergejus; Andersen, Peter Bach

2016-01-01

The Electric Vehicle (EV) has properties that can not only load but can elevate its value as a resource to the power system. An EV represents a high-power, fast-responding flexible demand unit, with an attached energy storage (battery) and the potential for bi-directional capabilities (V2G......). These properties can be used in a number of power and energy services, which can support power system operation while lowering the cost of EV ownership. Such services depend on the support from the communications technologies and standards that connect controllers and logic in the EVs with those in the charging...... for smart charging - to gain this ability by simply adhering to the widely supported IEC61851 standard. This paper describes the solution, demonstrates the implementation and discusses the potential it has for unlocking EV power- and energy services....

First principles study of NH3 molecular adsorption on LiH (100) surfaces

International Nuclear Information System (INIS)

Lu Xiaoxia; Chen Yuhong; Dong Xiao

2012-01-01

The adsorption of NH 3 on LiH (100) crystal surfaces was studied by first principles method. The preferred adsorption sites, adsorption energy, dissociation energy and electronic structure of the LiH (100)/NH 3 systems were calculated separately. It is found that chemical adsorption happened mainly when NH 3 molecules are on the LiH (100) crystal surfaces. When NH 3 is adsorbed on the Li top site, NH 2 is formed on the LiH (100) crystal surfaces after loss of H atom, the calculated adsorption energy, 0.511 eV, belongs to strong chemical adsorption, then the interaction is strongest. The interaction between NH 2 and the neighboring Li, H are ionic. The covalent bonds are formed between N and H atoms in NH 2 . One H 2 molecule is formed by another H atom in NH 3 and H atom from LiH (100) crystal sur- faces. The covalent bonds are formed between H and H atoms in H 2 . (authors)

Observation of the suppression of the flux of cosmic rays above 4x10(19) eV

NARCIS (Netherlands)

Abraham, J.; Abreu, P.; Aglietta, M.; Aguirre, C.; Allard, D.; Allekotte, I.; Allen, J.; Allison, P.; Alvarez-Muniz, J.; Ambrosio, M.; Anchordoqui, L.; Andringa, S.; Anzalone, A.; Aramo, C.; Argiro, S.; Arisaka, K.; Armengaud, E.; Arneodo, F.; Arqueros, F.; Asch, T.; Asorey, H.; Assis, P.; Atulugama, B. S.; Aublin, J.; Ave, M.; Avila, G.; Backer, T.; Badagnani, D.; Barbosa, A. F.; Barnhill, D.; Barroso, S. L. C.; Baughman, B.; Bauleo, P.; Beatty, J. J.; Beau, T.; Becker, B. R.; Becker, K. H.; Bellido, J. A.; BenZvi, S.; Berat, C.; Bergmann, T.; Bernardini, P.; Bertou, X.; Biermann, P. L.; Billoir, P.; Blanch-Bigas, O.; Blanco, F.; Blasi, P.; Bleve, C.; Mer, H. Blu; Bohacova, M.; Bonifazi, C.; Bonino, R.; Brack, J.; Brogueira, P.; Brown, W. C.; Buchholz, P.; Bueno, A.; Burton, R. E.; Busca, N. G.; Caballero-Mora, K. S.; Cai, B.; Camin, D. V.; Caramete, L.; Caruso, R.; Carvalho, W.; Castellina, A.; Catalano, O.; Cataldi, G.; Cazon, L.; Cester, R.; Chauvin, J.; Chiavassa, A.; Chinellato, J. A.; Chou, A.; Chudoba, J.; Chye, J.; Clark, P. D. J.; Clay, R. W.; Colombo, E.; Conceicao, R.; Connolly, B.; Contreras, F.; Coppens, J.; Cordier, A.; Cotti, U.; Coutu, S.; Covault, C. E.; Creusot, A.; Criss, A.; Cronin, J.; Curutiu, A.; Dagoret-Campagne, S.; Daumiller, K.; Dawson, B. R.; de Almeida, R. M.; de Donato, C.; de Jong, S. J.; De La Vega, G.; Junior, W. J. M. de Mello; de Mello Neto, J. R. T.; De Mitri, I.; de Souza, V.; del Peral, L.; Deligny, O.; Della Selva, A.; Delle Fratte, C.; Dembinski, H.; Di Giulio, C.; Diaz, J. C.; Diep, P. N.; Dobrigkeit, C.; D'Olivo, J. C.; Dong, P. N.; Dornic, D.; Dorofeev, A.; dos Anjos, J. C.; Dova, M. T.; D'Urso, D.; Dutan, I.; DuVernois, M. A.; Engel, R.; Epele, L.; Escobar, C. O.; Etchegoyen, A.; Luis, P. Facal San; Falcke, H.; Farrar, G.; Fauth, A. C.; Fazzini, N.; Ferrer, F.; Ferrero, A.; Fick, B.; Filevich, A.; Filipcic, A.; Fleck, I.; Fracchiolla, C. E.; Fulgione, W.; Garcia, B.; Gamez, D. Garcia; Garcia-Pinto, D.; Garrido, X.; Geenen, H.; Gelmini, G.; Gemmeke, H.; Ghia, P. L.; Giller, M.; Glass, H.; Gold, M. S.; Golup, G.; Albarracin, F. Gomez; Berisso, M. Gomez; Goncalves, P.; do Amaral, M. Goncalves; Gonzalez, D.; Gonzalez, J. G.; Gonzalez, M.; Gora, D.; Gorgi, A.; Gouffon, P.; Grassi, V.; Grillo, A. F.; Grunfeld, C.; Guardincerri, Y.; Guarino, F.; Guedes, G. P.; Gutierrez, J.; Hague, J. D.; Halenka, V.; Hamilton, J. C.; Hansen, P.; Harari, D.; Harmsma, S.; Harton, J. L.; Haungs, A.; Hauschildt, T.; Healy, M. D.; Hebbeker, T.; Hebrero, G.; Heck, D.; Hojvat, C.; Holmes, V. C.; Homola, P.; Horandel, J. R.; Horneffer, A.; Hrabovsky, M.; Huege, T.; Hussain, M.; Iarlori, M.; Insolia, A.; Ionita, F.; Italiano, A.; Kaducak, M.; Kampert, K. H.; Karova, T.; Kasper, P.; Kegl, B.; Keilhauer, B.; Kemp, E.; Kieckhafer, R. M.; Klages, H. O.; Kleifges, M.; Kleinfeller, J.; Knapik, R.; Knapp, J.; Koang, D. -H.; Krieger, A.; Kroemer, O.; Kuempel, D.; Kunka, N.; Kusenko, A.; La Rosa, G.; Lachaud, C.; Lago, B. L.; Lebrun, D.; Lebrun, P.; Lee, J.; de Oliveira, M. A. Leigui; Letessier-Selvon, A.; Leuthold, M.; Lhenry-Yvon, I.; Lopez, R.; Aguera, A. Lopez; Bahilo, J. Lozano; Lucero, A.; Garcia, R. Luna; Maccarone, M. C.; Macolino, C.; Maldera, S.; Mancarella, G.; Mancenido, M. E.; Mandat, D.; Mantsch, P.; Mariazzi, A. G.; Maris, I. C.; Falcon, H. R. Marquez; Martello, D.; Martinez, J.; Bravo, O. Martinez; Mathes, H. J.; Matthews, J.; Matthews, J. A. J.; Matthiae, G.; Maurizio, D.; Mazur, P. O.; McCauley, T.; McEwen, M.; McNeil, R. R.; Medina, M. C.; Medina-Tanco, G.; Melo, D.; Menichetti, E.; Menschikov, A.; Meurer, C.; Meyhandan, R.; Micheletti, M. I.; Miele, G.; Miller, W.; Mollerach, S.; Monasor, M.; Ragaigne, D. Monnier; Montanet, F.; Morales, B.; Morello, C.; Moreno, J. C.; Morris, C.; Mostafa, M.; Muller, M. A.; Mussa, R.; Navarra, G.; Navarro, J. L.; Navas, S.; Necesal, P.; Nellen, L.; Newman-Holmes, C.; Newton, D.; Nhung, P. T.; Nierstenhoefer, N.; Nitz, D.; Nosek, D.; Nozka, L.; Oehlschlaeger, J.; Ohnuki, T.; Olinto, A.; Olmos-Gilbaja, V. M.; Ortiz, M.; Ortolani, F.; Ostapchenko, S.; Otero, L.; Pacheco, N.; Selmi-Dei, D. Pakk; Palatka, M.; Pallotta, J.; Parente, G.; Parizot, E.; Parlati, S.; Pastor, S.; Patel, M.; Paul, T.; Pavlidou, V.; Payet, K.; Pech, M.; Pekala, J.; Pelayo, R.; Pepe, I. M.; Perrone, L.; Pesce, R.; Petrera, S.; Petrinca, P.; Petrov, Y.; Pichel, A.; Piegaia, R.; Pierog, T.; Pimenta, M.; Pinto, T.; Pirronello, V.; Pisanti, O.; Platino, M.; Pochon, J.; Privitera, P.; Prouza, M.; Quel, E. J.; Rautenberg, J.; Redondo, A.; Reucroft, S.; Revenu, B.; Rezende, F. A. S.; Ridky, J.; Riggi, S.; Risse, M.; Riviere, C.; Rizi, V.; Roberts, M.; Robledo, C.; Rodriguez, G.; Martino, J. Rodriguez; Rojo, J. Rodriguez; Rodriguez-Cabo, I.; Rodriguez-Frias, M. D.; Ros, G.; Rosado, J.; Roth, M.; Rouille-d'Orfeuil, B.; Roulet, E.; Rovero, A. C.; Salamida, F.; Salazar, H.; Salina, G.; Sanchez, F.; Santander, M.; Santo, C. E.; Santos, E. M.; Sarazin, F.; Sarkar, S.; Sato, R.; Scherini, V.; Schieler, H.; Schmidt, A.; Schmidt, F.; Schmidt, T.; Scholten, O.; Schovanek, P.; Schroeder, F.; Schulte, S.; Schuessler, F.; Sciutto, S. J.; Scuderi, M.; Segreto, A.; Semikoz, D.; Settimo, M.; Shellard, R. C.; Sidelnik, I.; Siffert, B. B.; Sigl, G.; De Grande, N. Smetniansky; Smialkowski, A.; Smida, R.; Smith, A. G. K.; Smith, B. E.; Snow, G. R.; Sokolsky, P.; Sommers, P.; Sorokin, J.; Spinka, H.; Squartini, R.; Strazzeri, E.; Stutz, A.; Suarez, F.; Suomijaervi, T.; Supanitsky, A. D.; Sutherland, M. S.; Swain, J.; Szadkowski, Z.; Takahashi, J.; Tamashiro, A.; Tamburro, A.; Tarutina, T.; Tascau, O.; Tcaciuc, R.; Thao, N. T.; Thomas, D.; Ticona, R.; Tiffenberg, J.; Timmermans, C.; Tkaczyk, W.; Peixoto, C. J. Todero; Tome, B.; Tonachini, A.; Torres, I.; Travnicek, P.; Tripathi, A.; Tristram, G.; Tscherniakhovski, D.; Tuci, V.; Tueros, M.; Tunnicliffe, V.; Ulrich, R.; Unger, M.; Urban, M.; Galicia, J. F. Valdes; Valino, I.; Valore, L.; van den Berg, A. M.; van Elewyck, V.; Vazquez, R. A.; Veberic, D.; Veiga, A.; Velarde, A.; Venters, T.; Verzi, V.; Videla, M.; Villasenor, L.; Vorobiov, S.; Voyvodic, L.; Wahlberg, H.; Wahrlich, P.; Wainberg, O.; Walker, P.; Warner, D.; Watson, A. A.; Westerhoff, S.; Wieczorek, G.; Wiencke, L.; Wilczynska, B.; Wilczynski, H.; Wileman, C.; Winnick, M. G.; Wu, H.; Wundheiler, B.; Yamamoto, T.; Younk, P.; Zas, E.; Zavrtanik, D.; Zavrtanik, M.; Zaw, I.; Zepeda, A.; Ziolkowski, M.

2008-01-01

The energy spectrum of cosmic rays above 2.5 x 10(18) eV, derived from 20 000 events recorded at the Pierre Auger Observatory, is described. The spectral index gamma of the particle flux, J proportional to E(-gamma), at energies between 4 x 10(18) eV and 4 x 10(19) eV is 2.69 +/- 0.02(stat) +/-

Designing Universitas Indonesia Molina EV Bus Dashboard Using ECQFD and TRIZ

Science.gov (United States)

Faiq Pradhila, Muhammad; Suzianti, Amalia; Putri Adinda, Prilly

2018-01-01

Universitas Indonesia is involved in the national electric car development program. One of the focus by the research team is to develop the Molina EV Bus which is planned to replace the current operational bus at UI so that it can be more environmental friendly. With UI developing facilities for the disabled, the Molina research team planned to make a new prototype of the Molina EV Bus to contribute to the facilities developed for the disabled. The new prototype is expected to increase the quality of the previous features of the EV Bus, including the dashboard that had been ignored. To support the development of the new prototype, this research was conducted to design a suitable dashboard for the new prototype. Design of the prototype are made using Autodesk Inventor. This research used the integration of ECQFD (Environmentally Conscious Quality Function Deployment) and TRIZ (Theory of Inventive Problem Solving) method. ECQFD was used to translate user needs into quality characteristics based on environmental aspects. TRIZ was used to translate the quality characteristics into technical specifications. This research has generated 3 sustainable, innovative, and user-preferred dashboard design recommendation for the new prototype.

W/FeSb2/W Heterostructure for Single-Photon Detection in a Wide Range of Electromagnetic Spectrum

Directory of Open Access Journals (Sweden)

Armen KUZANYAN

2017-11-01

Full Text Available The results of computer simulation of heat distribution processes taking place after the absorption of single photons of 1 – 1000 eV energy in the three- layer detection pixel of the thermoelectric detector are being analyzed. Different geometries of the detection pixel with thermoelectric sensor made of strongly correlated semiconductor FeSb2, tungsten absorber and heat sink are considered. It is concluded that such detector may register individual photons from IR to X-ray providing energy resolution of not less than 1 % and terahertz counting rate.

Growth and surface morphology of ion-beam sputtered Ti-Ni thin films

International Nuclear Information System (INIS)

Rao, Ambati Pulla; Sunandana, C.S.

2008-01-01

Titanium-nickel thin films have been deposited on float glass substrates by ion beam sputtering in 100% pure argon atmosphere. Sputtering is predominant at energy region of incident ions, 1000 eV to 100 keV. The as-deposited films were investigated by X-ray photoelectron spectroscopy (XPS) and atomic force microscope (AFM). In this paper we attempted to study the surface morphology and elemental composition through AFM and XPS, respectively. Core level as well as valence band spectra of ion-beam sputtered Ti-Ni thin films at various Ar gas rates (5, 7 and 12 sccm) show that the thin film deposited at 3 sccm possess two distinct peaks at binding energies 458.55 eV and 464.36 eV mainly due to TiO 2 . Upon increasing Ar rate oxidation of Ti-Ni is reduced and the Ti-2p peaks begin approaching those of pure elemental Ti. Here Ti-2p peaks are observed at binding energy positions of 454.7 eV and 460.5 eV. AFM results show that the average grain size and roughness decrease, upon increasing Ar gas rate, from 2.90 μm to 0.096 μm and from 16.285 nm to 1.169 nm, respectively

Recent ion measurements within the modified DPF-1000U facility

Directory of Open Access Journals (Sweden)

Kwiatkowski Roch

2015-06-01

Full Text Available In this note we describe measurements of ion beams emitted along the z-axis of the DPF-1000U facility operated at 23 kV, 334 kJ, and with the initial deuterium pressure of 1.6–2 hPa. The DPF-1000U device was recently renewed and equipped with a dynamic gas-puff valve placed inside the inner electrode. The investigated ions were recorded by means of ion pinhole cameras equipped with solid state nuclear track detectors of the PM-355® (PADC type. The energy spectra of ions were determined using a Thomson spectrometer placed on the symmetry axis at a distance of 160 cm from the electrodes outlets. The ion images recorded during discharges performed under different experimental conditions show that the ion beams have a complex structure, usually in the form of a central bunch and an annular stream composed of many micro-beams. Energies of the registered deuterons have been in the range of 30–700 keV, while the fast protons (which originated from the hydrogen remnants had energies in the range of 300–850 keV.