WorldWideScience

Sample records for eurotrans project optimisation

  1. Nudatra: nuclear data for transmutation in IP-Eurotrans

    International Nuclear Information System (INIS)

    Gonzalez, E.M.; Koning, A.; Leray, S.; Plompen, A.; Sanz, J.

    2007-01-01

    The objective of NUDATRA, Domain 5 of the EU Integrated Project EUROTRANS (FI6W-CT-2004- 516520), is to improve and validate the nuclear data and simulation tools required for the development and optimisation of nuclear waste transmutation, ADS dedicated transmutation systems and the associated fuel cycle. Activities are essentially aimed at supplementing the evaluated nuclear data libraries and improving the reaction models for materials in transmutation fuels, coolants, spallation targets, internal structures, and reactor and accelerator shielding, relevant for the design and optimisation of the ETD and XT-ADS. These activities are distributed over four Work Packages: Sensitivity Analysis and Validation of Nuclear Data and Simulation Tools; Low- and Intermediate-energy Nuclear Data Measurements; Nuclear Data Libraries Evaluation and Low-intermediate Energy Models; and High-energy Experiments and Modelling.The main accomplishments expected from NUDATRA are: 1) new measurements and evaluations of Pb-Bi cross-sections, i.e. inelastic, (n,xn) and isomer branching ratios (Po production); 2) new measurements and evaluations for minor actinides particularly the capture in 243 Am and fission on 244 Cm; 3) improvement of TALYS as an evaluation tool and as an a priori model for the estimation of low- and intermediate-energy reaction cross-section; 4) high-energy model improvement based on measurements, particularly for the prediction of the spallation products, and gas (H, He) production cross-sections; 5) sensitivity and uncertainty analysis of ETD fuel cycle and related covariance issues. (authors)

  2. Transmutation of high level nuclear waste in an accelerator driven system: towards a demonstration device of industrial interest (EUROTRANS)

    International Nuclear Information System (INIS)

    Knebel, Joachim U.; Ait Abderrahim, Hamid; Caron-Carles, Marylise

    2010-01-01

    The Integrated Project EUROTRANS (EURopean Research Programme for the TRANSmutation of High Level Nuclear Waste in an Accelerator Driven System) within the ongoing EURATOM 6th Framework Programme (FP6) is devoted to the study of transmutation of high-level waste from nuclear power plants. The work is focused on transmutation in an Accelerator Driven System (ADS). The objective of EUROTRANS is the assessment of the design and the feasibility of an industrial ADS prototype dedicated to transmutation. The necessary R and D results in the areas of accelerator components, fuel development, structural materials, thermal-hydraulics, heavy liquid metal technology and nuclear data will be made available, together with the experimental demonstration of the ADS component coupling. The outcome of this work will allow to provide a reasonably reliable assessment of technological feasibility and a cost estimate for ADS based transmutation, and to possibly decide on the detailed design of an experimental ADS and its construction in the future. EUROTRANS is integrating activities of 51 participants from 16 countries, within the industry (10 participants), the national research centres (20) and 17 universities. 16 universities are collectively represented by ENEN (European Nuclear Education Network). EUROTRANS is the continuation of the three FP5 Clusters FUETRA, BASTRA and TESTRA together with the PDS-XADS Project. It is a five-year project which started in April 2005

  3. Research and development activities around the EUROTRANS accelerator for ADS applications

    International Nuclear Information System (INIS)

    Biarrotte, J. L.; Mueller, A. C.

    2007-01-01

    An Accelerator Driven System (ADS) for transmutation of nuclear waste typically requires a 600 MeV - 1 GeV accelerator delivering a proton flux of a few mAs for demonstrators, and of a few tens of mAs for large industrial systems. Such a machine belongs to the category of the high power proton accelerators, with an additional requirement for exceptional 'reliability': because of the induced thermal stress to the subcritical core, the number of unwanted 'beam-trips' should not exceed a few per year, a specification that is several orders of magnitude above usual performance. This paper briefly describes the reference solution adopted for such a machine, based on a linear superconducting accelerator, and presents the status of the Research and Development performed in this context. This work is performed within the 6th Framework Program EC project 'EUROTRANS' (EC Contract No: FI6W 516520, 'EUROTRANS')

  4. UPAYA MENINGKATKAN LAYANAN JASA DAN MENURUNKAN CUSTOMER COMPLAIN MENGGUNAKAN METODE FUZZY- SERVQUAL DI PT. EUROTRANS CHARTER INDONESIA

    Directory of Open Access Journals (Sweden)

    Febri Yanti

    2017-10-01

    Full Text Available PT. Eurotrans Charter Indonesia Fowarding Freight is a company engaged in the transportation services that keep in touch with customers. In the development of its PT. Eurotrans Charter Indonesia decreased its shipment (number of document processing requests. To keep keeksistensianya PT. Eurotrans Charter Indonesia Need to maintain the quality of ministry. Thus the need for a method to measure the quality of service PT. Eurotrans Charter Indonesia and the need to improve the quality of services provided so that customers feel comfortable and satisfied so that it can survive to compete with competitors PT Forwarding lainnya.Langkah-steps involved in data collection is done by observation and questionnaires from several criteria. Those criteria obtained through interviews and studies pustaka..Metode used to measure the quality of service using Fuzzy Servqual. The results of data processing, found that the value of fuzzy-servqual per criteria, perdimensi and overall By using 5 Dimensions in servqual namely: direct evidence (Tangibles, Reliability (Reliability, Responsiveness (Responsiveness, Security (Assurance, Empathy (Empathy. After measuring the quality of service PT. Eurotrans Charter Indonesia found the results showed that customers' expectations have not been in accordance with the perception of the services they receive. Results gap of -1.06 and therefore the management of PT. Eurotrans Charter of Indonesia needs to make improvements of service quality for the sake of reducing the existing gap. To make improvements to the company made by using analysis 5W1H (what, why, when where, who and how .After note 5 biggest gap in ": Various complete facilities provided by the management, .Kemudahan in payment processing, support services revision PT. Eurotrans Charter Indonesia do a double check and do not make mistakes in working document. quotation (supply that is given an interesting, and hospitality employees to customers, After the PT. Eurotrans

  5. IP EUROTRANS: from MYRRHA towards XT-ADS

    International Nuclear Information System (INIS)

    Debruyn, D.

    2006-01-01

    The integrated project (IP) EUROTRANS (EUROpean Research Programme for the TRANSmutation of High-Level Nuclear Waste in an Accelerator Driven System) has been launched in the Euratom Sixth Framework Programme (FP6) and has officially started in April 2005 for a duration of four years. This project is the logical continuation of several activities worked out within the previous Framework Programme (FP5), namely the ADOPT network, the FUETRA, BASTRA and TESTRA clusters and the PDS-XADS project. The project is divided into five main sub-projects or domains (DMs). SCK-CEN coordinates the DM1 DESIGN described hereafter. The aim of DM2 ECATS is to provide validated experimental input from relevant coupling experiments of an accelerator, a spallation target and a sub-critical blanket, while the development and demonstration of the associated technologies is devoted to the remaining DMs, DM3 AFTRA (fuels), DM4 DEMETRA (heavy liquid metal technologies) and DM5 NUDATRA (nuclear data). The objective of the DM1 DESIGN of IP EUROTRANS is to proceed by a significant jump towards the demonstration of the industrial transmutation through the ADS route. The strategy of European Transmutation Demonstration (ETD) is carried out with two interconnected activities: (1) the first activity is to develop an advanced design file leading to a short-term (i.e. realisation within the next 10 years) experimental demonstration of the technical feasibility of Transmutation (at 50 to 100 MWth) in an Accelerator Driven System (XT-ADS). Liquid lead-bismuth eutectic (LBE) is used as primary coolant and material for the spallation target and the core is designed with standard MOX fuel; (2) the second activity is to carry out in parallel a reference conceptual design for a modular EFIT (European Facility for Industrial Transmutation) machine with a power of up to several 100 MWth, as a basis for a cost estimate and safety studies for an ADS-based transmutation system. For the EFIT, liquid lead is used

  6. Noise aspects at aerodynamic blade optimisation projects

    International Nuclear Information System (INIS)

    Schepers, J.G.

    1997-06-01

    The Netherlands Energy Research Foundation (ECN) has often been involved in industrial projects, in which blade geometries are created automatic by means of numerical optimisation. Usually, these projects aim at the determination of the aerodynamic optimal wind turbine blade, i.e. the goal is to design a blade which is optimal with regard to energy yield. In other cases, blades have been designed which are optimal with regard to cost of generated energy. However, it is obvious that the wind turbine blade designs which result from these optimisations, are not necessarily optimal with regard to noise emission. In this paper an example is shown of an aerodynamic blade optimisation, using the ECN-program PVOPT. PVOPT calculates the optimal wind turbine blade geometry such that the maximum energy yield is obtained. Using the aerodynamic optimal blade design as a basis, the possibilities of noise reduction are investigated. 11 figs., 8 refs

  7. A STUDY ON OPTIMISATION OF RESOURCES FOR MULTIPLE PROJECTS BY USING PRIMAVERA

    Directory of Open Access Journals (Sweden)

    B. S. K. REDDY

    2015-02-01

    Full Text Available Resources play vital role in construction projects. The performance of construction industry depends chiefly on how best the resources are managed. Optimisation play pivotal role in resource management, but task is highly haphazard and chaotic under the influence of complexities and vastness. Management always looks for optimum utility of resources available with them. Hence, the project management has got important place especially in resource allocation and smooth functioning with allocated budget. To achieve these goals and to exercise enhance optimisation certain tools are used for resource allocation optimally. Present work illustrates resource optimisation exercises on two ongoing projects in Dubai, UAE. Resource demands of project A & B are individually levelled and observed cumulative requirement is 17475. In other option demands of projects A & B are aggregated and then together levelled, the necessary resource observed is 16490. Comparison of individually levelled and then combined option with aggregated and then levelled clearly indicates reduction in demand of resources by 5.65% in later option, which could be best considered for economy.

  8. Optimising Impact in Astronomy for Development Projects

    Science.gov (United States)

    Grant, Eli

    2015-08-01

    Positive outcomes in the fields of science education and international development are notoriously difficult to achieve. Among the challenges facing projects that use astronomy to improve education and socio-economic development is how to optimise project design in order to achieve the greatest possible benefits. Over the past century, medical scientists along with statisticians and economists have progressed an increasingly sophisticated and scientific approach to designing, testing and improving social intervention and public health education strategies. This talk offers a brief review of the history and current state of `intervention science'. A similar framework is then proposed for astronomy outreach and education projects, with applied examples given of how existing evidence can be used to inform project design, predict and estimate cost-effectiveness, minimise the risk of unintended negative consequences and increase the likelihood of target outcomes being achieved.

  9. Adapting the MYRRHA concept to meet the XT-ADS objectives

    International Nuclear Information System (INIS)

    De Bruyn, D.

    2007-01-01

    The EUROTRANS project is an integrated project in the Sixth European Framework Program in the context of Partitioning and Transmutation. The objective of this project is the step-wise approach to a European Transmutation Demonstration. This project aims to deliver an advanced design of a small-scale Accelerator Driven System (ADS), XT-ADS, as well as the conceptual design of a European Facility for Industrial Transmutation, EFIT. The partners of this project accepted to use the MYRRHA Draft-2 design file as a starting basis for the design of the short-term XT-ADS demonstration machine. Instead of starting from a blank page, this allowed optimising an existing design towards the needs of XT-ADS, and within the limits of safety requirements. Many options have been revisited and the framework is now set up. While our MYRRHA Draft-2 design file was still a conceptual design, our intention is to get at the end of the EUROTRANS project (March 2009) an advanced design of the XT-ADS machine, albeit a first advanced design. Moreover, industrial partners (Ansaldo Nucleare, Areva) will contribute to this XT-ADS design

  10. Smart border initiative: a Franco-German cross-border energy optimisation project

    International Nuclear Information System (INIS)

    2017-01-01

    Integrated and optimised local energy systems will play a key role in achieving the energy transition objectives set by France and Germany, in line with the Energy Union's goals, and contribute to ensuring a secure, affordable and climate-friendly energy supply in the EU. In order to capitalise on the French and German expertise and experiences in developing such systems and to continue strengthening the cross-border cooperation towards a fully integrated European energy market, both Governments have decided to launch a common initiative to identify and structure a cross-border energy optimisation project. Tilia and Dena have undertaken this mission to jointly develop the Smart Border Initiative (SBI). The SBI will, on the one hand, connect policies designed by France and Germany in order to support their cities and territories in their energy transition strategies and European market integration. It is currently a paradox that, though more balanced and resilient energy systems build up, bottom-up, at the local level, borders remain an obstacle to this local integration, in spite of the numerous complementarities observed in cross-border regions, and of their specific needs, in terms of smart mobility for example. The SBI project aims at enabling European neighbouring regions separated by a border to jointly build up optimised local energy systems, and jointly develop their local economies following an integrated, sustainable and low-carbon model. On the other hand, this showcase project will initiate a new stage in the EU electricity market integration, by completing high voltage interconnections with local, low voltage integration at DSO level, opening new optimisation possibilities in managing the electricity balance, and enabling DSOs to jointly overcome some of the current challenges, notably the increased share of renewable energy (RE) and ensuring Europe's security of supply

  11. Advanced optimisation - coal fired power plant operations

    Energy Technology Data Exchange (ETDEWEB)

    Turney, D.M.; Mayes, I. [E.ON UK, Nottingham (United Kingdom)

    2005-03-01

    The purpose of this unit optimization project is to develop an integrated approach to unit optimisation and develop an overall optimiser that is able to resolve any conflicts between the individual optimisers. The individual optimisers have been considered during this project are: on-line thermal efficiency package, GNOCIS boiler optimiser, GNOCIS steam side optimiser, ESP optimisation, and intelligent sootblowing system. 6 refs., 7 figs., 3 tabs.

  12. Sequential projection pursuit for optimised vibration-based damage detection in an experimental wind turbine blade

    Science.gov (United States)

    Hoell, Simon; Omenzetter, Piotr

    2018-02-01

    To advance the concept of smart structures in large systems, such as wind turbines (WTs), it is desirable to be able to detect structural damage early while using minimal instrumentation. Data-driven vibration-based damage detection methods can be competitive in that respect because global vibrational responses encompass the entire structure. Multivariate damage sensitive features (DSFs) extracted from acceleration responses enable to detect changes in a structure via statistical methods. However, even though such DSFs contain information about the structural state, they may not be optimised for the damage detection task. This paper addresses the shortcoming by exploring a DSF projection technique specialised for statistical structural damage detection. High dimensional initial DSFs are projected onto a low-dimensional space for improved damage detection performance and simultaneous computational burden reduction. The technique is based on sequential projection pursuit where the projection vectors are optimised one by one using an advanced evolutionary strategy. The approach is applied to laboratory experiments with a small-scale WT blade under wind-like excitations. Autocorrelation function coefficients calculated from acceleration signals are employed as DSFs. The optimal numbers of projection vectors are identified with the help of a fast forward selection procedure. To benchmark the proposed method, selections of original DSFs as well as principal component analysis scores from these features are additionally investigated. The optimised DSFs are tested for damage detection on previously unseen data from the healthy state and a wide range of damage scenarios. It is demonstrated that using selected subsets of the initial and transformed DSFs improves damage detectability compared to the full set of features. Furthermore, superior results can be achieved by projecting autocorrelation coefficients onto just a single optimised projection vector.

  13. Revisiting EOR Projects in Indonesia through Integrated Study: EOR Screening, Predictive Model, and Optimisation

    KAUST Repository

    Hartono, A. D.; Hakiki, Farizal; Syihab, Z.; Ambia, F.; Yasutra, A.; Sutopo, S.; Efendi, M.; Sitompul, V.; Primasari, I.; Apriandi, R.

    2017-01-01

    EOR preliminary analysis is pivotal to be performed at early stage of assessment in order to elucidate EOR feasibility. This study proposes an in-depth analysis toolkit for EOR preliminary evaluation. The toolkit incorporates EOR screening, predictive, economic, risk analysis and optimisation modules. The screening module introduces algorithms which assimilates statistical and engineering notions into consideration. The United States Department of Energy (U.S. DOE) predictive models were implemented in the predictive module. The economic module is available to assess project attractiveness, while Monte Carlo Simulation is applied to quantify risk and uncertainty of the evaluated project. Optimization scenario of EOR practice can be evaluated using the optimisation module, in which stochastic methods of Genetic Algorithms (GA), Particle Swarm Optimization (PSO) and Evolutionary Strategy (ES) were applied in the algorithms. The modules were combined into an integrated package of EOR preliminary assessment. Finally, we utilised the toolkit to evaluate several Indonesian oil fields for EOR evaluation (past projects) and feasibility (future projects). The attempt was able to update the previous consideration regarding EOR attractiveness and open new opportunity for EOR implementation in Indonesia.

  14. Revisiting EOR Projects in Indonesia through Integrated Study: EOR Screening, Predictive Model, and Optimisation

    KAUST Repository

    Hartono, A. D.

    2017-10-17

    EOR preliminary analysis is pivotal to be performed at early stage of assessment in order to elucidate EOR feasibility. This study proposes an in-depth analysis toolkit for EOR preliminary evaluation. The toolkit incorporates EOR screening, predictive, economic, risk analysis and optimisation modules. The screening module introduces algorithms which assimilates statistical and engineering notions into consideration. The United States Department of Energy (U.S. DOE) predictive models were implemented in the predictive module. The economic module is available to assess project attractiveness, while Monte Carlo Simulation is applied to quantify risk and uncertainty of the evaluated project. Optimization scenario of EOR practice can be evaluated using the optimisation module, in which stochastic methods of Genetic Algorithms (GA), Particle Swarm Optimization (PSO) and Evolutionary Strategy (ES) were applied in the algorithms. The modules were combined into an integrated package of EOR preliminary assessment. Finally, we utilised the toolkit to evaluate several Indonesian oil fields for EOR evaluation (past projects) and feasibility (future projects). The attempt was able to update the previous consideration regarding EOR attractiveness and open new opportunity for EOR implementation in Indonesia.

  15. Risk based test interval and maintenance optimisation - Application and uses

    International Nuclear Information System (INIS)

    Sparre, E.

    1999-10-01

    The project is part of an IAEA co-ordinated Research Project (CRP) on 'Development of Methodologies for Optimisation of Surveillance Testing and Maintenance of Safety Related Equipment at NPPs'. The purpose of the project is to investigate the sensitivity of the results obtained when performing risk based optimisation of the technical specifications. Previous projects have shown that complete LPSA models can be created and that these models allow optimisation of technical specifications. However, these optimisations did not include any in depth check of the result sensitivity with regards to methods, model completeness etc. Four different test intervals have been investigated in this study. Aside from an original, nominal, optimisation a set of sensitivity analyses has been performed and the results from these analyses have been compared to the original optimisation. The analyses indicate that the result of an optimisation is rather stable. However, it is not possible to draw any certain conclusions without performing a number of sensitivity analyses. Significant differences in the optimisation result were discovered when analysing an alternative configuration. Also deterministic uncertainties seem to affect the result of an optimisation largely. The sensitivity of failure data uncertainties is important to investigate in detail since the methodology is based on the assumption that the unavailability of a component is dependent on the length of the test interval

  16. The GUINEVERE-project: the first zero-power fast lead reactor coupled to a 14 MeV neutron generator (GENEPI)

    International Nuclear Information System (INIS)

    Baeten, P.

    2007-01-01

    The GUINEVERE project is an European project in the framework of FP6 IP-EUROTRANS. The IP-EUROTRANS project aims at addressing the main issues for ADS development in the framework of partitioning and transmutation for nuclear waste volume and radio toxicity reduction. The GUINEVERE-project is carried out in the context of domain 2 of IP-EUROTRANS, ECATS, devoted to specific experiments for the coupling of an accelerator, a target and a subcritical core. These experiments should provide an answer to the questions of on-line reactivity monitoring, sub-criticality determination and operational procedures (loading, start-up, shut-down) in an ADS by 2009-2010. During the definition of the experimental programme ECATS, it was judged that there was a strong need for a European managed experiment in the line of the FP5 MUSE-project. Reanalyzing the outcome of MUSE, two points were left open for significant improvement. To validate the methodology for reactivity monitoring, a continuous beam is needed, which was not present in the MUSE-project. In the definition of the MUSE-project, from the beginning a strong request was made for a lead core in order to have representative conditions of a lead-cooled ADS which was only partially answered by the MUSE-programme. Therefore, there is a need for a lead fast critical facility connected to a continuous beam accelerator. Since such a programme/installation is not present at the European nor at the international level, SCK-CEN has proposed to use a modified VENUS critical facility located at its Mol-site and to couple it to a modified GENEPI deuteron accelerator (used in MUSE) working in current mode delivering 14 MeV neutrons by bombardment of deuterons on a tritium-target: the GUINEVERE-project (Generator of Uninterrupted Intense NEutrons at the lead VEnus REactor). This proposal was formally accepted by the Governing Council of IP-Eurotrans in December 2006. This project represents a close collaboration between SCK-CEN, CEA and

  17. Simulation optimisation

    International Nuclear Information System (INIS)

    Anon

    2010-01-01

    Over the past decade there has been a significant advance in flotation circuit optimisation through performance benchmarking using metallurgical modelling and steady-state computer simulation. This benchmarking includes traditional measures, such as grade and recovery, as well as new flotation measures, such as ore floatability, bubble surface area flux and froth recovery. To further this optimisation, Outotec has released its HSC Chemistry software with simulation modules. The flotation model developed by the AMIRA P9 Project, of which Outotec is a sponsor, is regarded by industry as the most suitable flotation model to use for circuit optimisation. This model incorporates ore floatability with flotation cell pulp and froth parameters, residence time, entrainment and water recovery. Outotec's HSC Sim enables you to simulate mineral processes in different levels, from comminution circuits with sizes and no composition, through to flotation processes with minerals by size by floatability components, to full processes with true particles with MLA data.

  18. Accurate KAP meter calibration as a prerequisite for optimisation in projection radiography

    International Nuclear Information System (INIS)

    Malusek, A.; Sandborg, M.; Alm Carlsson, G.

    2016-01-01

    Modern X-ray units register the air kerma-area product, PKA, with a built-in KAP meter. Some KAP meters show an energy-dependent bias comparable with the maximum uncertainty articulated by the IEC (25 %), adversely affecting dose-optimisation processes. To correct for the bias, a reference KAP meter calibrated at a standards laboratory and two calibration methods described here can be used to achieve an uncertainty of <7 % as recommended by IAEA. A computational model of the reference KAP meter is used to calculate beam quality correction factors for transfer of the calibration coefficient at the standards laboratory, Q 0 , to any beam quality, Q, in the clinic. Alternatively, beam quality corrections are measured with an energy-independent dosemeter via a reference beam quality in the clinic, Q 1 , to beam quality, Q. Biases up to 35 % of built-in KAP meter readings were noted. Energy-dependent calibration factors are needed for unbiased PKA. Accurate KAP meter calibration as a prerequisite for optimisation in projection radiography. (authors)

  19. Optimisation of Critical Infrastructure Protection: The SiVe Project on Airport Security

    Science.gov (United States)

    Breiing, Marcus; Cole, Mara; D'Avanzo, John; Geiger, Gebhard; Goldner, Sascha; Kuhlmann, Andreas; Lorenz, Claudia; Papproth, Alf; Petzel, Erhard; Schwetje, Oliver

    This paper outlines the scientific goals, ongoing work and first results of the SiVe research project on critical infrastructure security. The methodology is generic while pilot studies are chosen from airport security. The outline proceeds in three major steps, (1) building a threat scenario, (2) development of simulation models as scenario refinements, and (3) assessment of alternatives. Advanced techniques of systems analysis and simulation are employed to model relevant airport structures and processes as well as offences. Computer experiments are carried out to compare and optimise alternative solutions. The optimality analyses draw on approaches to quantitative risk assessment recently developed in the operational sciences. To exploit the advantages of the various techniques, an integrated simulation workbench is build up in the project.

  20. Mechatronic System Design Based On An Optimisation Approach

    DEFF Research Database (Denmark)

    Andersen, Torben Ole; Pedersen, Henrik Clemmensen; Hansen, Michael Rygaard

    The envisaged objective of this paper project is to extend the current state of the art regarding the design of complex mechatronic systems utilizing an optimisation approach. We propose to investigate a novel framework for mechatronic system design. The novelty and originality being the use...... of optimisation techniques. The methods used to optimise/design within the classical disciplines will be identified and extended to mechatronic system design....

  1. Optimization of the reliability of ADS accelerators in the framework of the EUROTRANS project; Optimisation de la fiabilite des accelerateurs ADS dans le cadre du projet EUROTRANS

    Energy Technology Data Exchange (ETDEWEB)

    Lucija, Lukovac

    2007-07-01

    In order to limit the number of thermal shocks in the spallation targets and in the core of an ADS (Accelerator Driven System), it is necessary to limit the number of failures of the beam accelerating system. This article presents the improvements in terms of reliability for 2 sub-systems of the ADS: the control system that is in charge of the RF power equipment that delivers the energy necessary to the accelerating system and the power coupler whose purpose is to transfer energy from RF generator to the accelerating cavities. The digitalization of the control system has allowed the application of a compensation method: if one of the cavities fails, the neighbouring cavities are regulated to limit the consequences of the failure on the beam. As for the power coupler, the ceramic window has been designed with great care. The improvements will be tested on 2 prototypes that are being built. (A.C.)

  2. MYRRHA/XT-ADS primary system design and experimental devices

    International Nuclear Information System (INIS)

    Maes, D.

    2009-01-01

    The EUROTRANS project is an integrated project in the Sixth European Framework Program in the context of Partitioning and Transmutation. The objective of this project is to work towards an ETD (European Transmutation Demonstration) in a step-wise manner. The first step is to carry out an advanced design of a small-scale XT-ADS (eXperimental Transmutation in an Accelerator Driven System) for realisation in a short-term (about 10 years) as well as to accomplish a generic conceptual design of EFIT (European Facility for Industrial Transmutation) for realisation in the long-term. The MYRRHA-2005 design served as a starting basis for the XT-ADS. Many options have been revisited and the framework is now set up. While the MYRRHA-2005 design was still a conceptual design, the intention is to get at the end of the EUROTRANS project (March 2009) an advanced design of the XT-ADS, albeit a first advanced design. While the design work performed during the first years of the project (2005-2006) was mainly devoted to optimise and enhance the primary and secondary system configuration according to the suggestions and contributions of our industrial partners (Ansaldo Nucleare, Areva, Suez-Tractebel) within the DM1 (Domain 1 D ESIGN ) , the last year work objectives mainly consisted of (1) the release of the Remote Handling Design Catalogue for XT-ADS and (2) the formulation of the specification of the experimental devices according to the XT-ADS objectives and adapted to the actual XT-ADS core and core support structure design; (3) the detailed calculations of the main XT-ADS primary and secondary system components

  3. Noise aspects at aerodynamic blade optimisation projects

    Energy Technology Data Exchange (ETDEWEB)

    Schepers, J.G. [Netherlands Energy Research Foundation, Petten (Netherlands)

    1997-12-31

    This paper shows an example of an aerodynamic blade optimisation, using the program PVOPT. PVOPT calculates the optimal wind turbine blade geometry such that the maximum energy yield is obtained. Using the aerodynamic optimal blade design as a basis, the possibilities of noise reduction are investigated. The aerodynamic optimised geometry from PVOPT is the `real` optimum (up to the latest decimal). The most important conclusion from this study is, that it is worthwhile to investigate the behaviour of the objective function (in the present case the energy yield) around the optimum: If the optimum is flat, there is a possibility to apply modifications to the optimum configuration with only a limited loss in energy yield. It is obvious that the modified configurations emits a different (and possibly lower) noise level. In the BLADOPT program (the successor of PVOPT) it will be possible to quantify the noise level and hence to assess the reduced noise emission more thoroughly. At present the most promising approaches for noise reduction are believed to be a reduction of the rotor speed (if at all possible), and a reduction of the tip angle by means of low lift profiles, or decreased twist at the outboard stations. These modifications were possible without a significant loss in energy yield. (LN)

  4. Defining a quantitative framework for evaluation and optimisation of the environmental impacts of mega-event projects.

    Science.gov (United States)

    Parkes, Olga; Lettieri, Paola; Bogle, I David L

    2016-02-01

    This paper presents a novel quantitative methodology for the evaluation and optimisation of the environmental impacts of the whole life cycle of a mega-event project: construction and staging the event and post-event site redevelopment and operation. Within the proposed framework, a mathematical model has been developed that takes into account greenhouse gas (GHG) emissions resulting from use of transportation fuel, energy, water and construction materials used at all stages of the mega-event project. The model is applied to a case study - the London Olympic Park. Three potential post-event site design scenarios of the Park have been developed: Business as Usual (BAU), Commercial World (CW) and High Rise High Density (HRHD). A quantitative summary of results demonstrates that the highest GHG emissions associated with the actual event are almost negligible compared to those associated with the legacy phase. The highest share of emissions in the legacy phase is attributed to embodied emissions from construction materials (almost 50% for the BAU and HRHD scenarios) and emissions resulting from the transportation of residents, visitors and employees to/from the site (almost 60% for the CW scenario). The BAU scenario is the one with the lowest GHG emissions compared to the other scenarios. The results also demonstrate how post-event site design scenarios can be optimised to minimise the GHG emissions. The overall outcomes illustrate how the proposed framework can be used to support decision making process for mega-event projects planning. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

  5. Experimental test of a supercritical helium heat exchanger dedicated to EUROTRANS 150 kW CW power coupler

    Science.gov (United States)

    Souli, M.; Fouaidy, M.; Hammoudi, N.

    2010-05-01

    The coaxial power coupler needed for beta = 0.65 superconducting RF cavities used in the high energy section of the EUROTRANS driver should transmit 150 kW (CW operation) RF power to the proton beam. The estimated RF losses on the power coupler outer conductor in standing wave mode operation are 46 W. To remove these heat loads, a full scale copper coil heat exchanger brazed around the outer conductor was designed and tested using supercritical helium at T = 6 K as a coolant. Our main objective was to minimise the heat loads to cold extremity of SRF cavity maintained at 2 K or 4.2 K. A dedicated test facility named SUPERCRYLOOP was developed and successfully operated in order to measure the performance of the cold heat exchanger. The test cell used reproduces the realistic thermal boundary conditions of the power coupler mounted on the cavity in the cryomodule. After a short introduction, a brief discussion about the problem of power coupler cooling systems in different machines is made. After that, we describe the experimental set-up and test apparatus. Then, a heat exchanger thermal model will be developed with FEM code COSMOS/M to estimate the different heat transfer coefficients by comparison between numerical simulation results and experimental data in order to validate the design. Finally, thermo-hydraulic behavior of supercritical helium has been investigated as function of different parameters (inlet pressure, flow rate, heat loads).

  6. Automatic optimisation of gamma dose rate sensor networks: The DETECT Optimisation Tool

    DEFF Research Database (Denmark)

    Helle, K.B.; Müller, T.O.; Astrup, Poul

    2014-01-01

    of the EU FP 7 project DETECT. It evaluates the gamma dose rates that a proposed set of sensors might measure in an emergency and uses this information to optimise the sensor locations. The gamma dose rates are taken from a comprehensive library of simulations of atmospheric radioactive plumes from 64......Fast delivery of comprehensive information on the radiological situation is essential for decision-making in nuclear emergencies. Most national radiological agencies in Europe employ gamma dose rate sensor networks to monitor radioactive pollution of the atmosphere. Sensor locations were often...... source locations. These simulations cover the whole European Union, so the DOT allows evaluation and optimisation of sensor networks for all EU countries, as well as evaluation of fencing sensors around possible sources. Users can choose from seven cost functions to evaluate the capability of a given...

  7. ATLAS software configuration and build tool optimisation

    Science.gov (United States)

    Rybkin, Grigory; Atlas Collaboration

    2014-06-01

    ATLAS software code base is over 6 million lines organised in about 2000 packages. It makes use of some 100 external software packages, is developed by more than 400 developers and used by more than 2500 physicists from over 200 universities and laboratories in 6 continents. To meet the challenge of configuration and building of this software, the Configuration Management Tool (CMT) is used. CMT expects each package to describe its build targets, build and environment setup parameters, dependencies on other packages in a text file called requirements, and each project (group of packages) to describe its policies and dependencies on other projects in a text project file. Based on the effective set of configuration parameters read from the requirements files of dependent packages and project files, CMT commands build the packages, generate the environment for their use, or query the packages. The main focus was on build time performance that was optimised within several approaches: reduction of the number of reads of requirements files that are now read once per package by a CMT build command that generates cached requirements files for subsequent CMT build commands; introduction of more fine-grained build parallelism at package task level, i.e., dependent applications and libraries are compiled in parallel; code optimisation of CMT commands used for build; introduction of package level build parallelism, i. e., parallelise the build of independent packages. By default, CMT launches NUMBER-OF-PROCESSORS build commands in parallel. The other focus was on CMT commands optimisation in general that made them approximately 2 times faster. CMT can generate a cached requirements file for the environment setup command, which is especially useful for deployment on distributed file systems like AFS or CERN VMFS. The use of parallelism, caching and code optimisation significantly-by several times-reduced software build time, environment setup time, increased the efficiency of

  8. Optimisation of efficiency of axial fans

    NARCIS (Netherlands)

    Kruyt, Nicolaas P.; Pennings, P.C.; Faasen, R.

    2014-01-01

    A three-stage research project has been executed to develop ducted axial-fans with increased efficiency. In the first stage a design method has been developed in which various conflicting design criteria can be incorporated. Based on this design method, an optimised design has been determined

  9. Optimisation in radiotherapy II: Programmed and inversion optimisation algorithms

    International Nuclear Information System (INIS)

    Ebert, M.

    1997-01-01

    This is the second article in a three part examination of optimisation in radiotherapy. The previous article established the bases of optimisation in radiotherapy, and the formulation of the optimisation problem. This paper outlines several algorithms that have been used in radiotherapy, for searching for the best irradiation strategy within the full set of possible strategies. Two principle classes of algorithm are considered - those associated with mathematical programming which employ specific search techniques, linear programming type searches or artificial intelligence - and those which seek to perform a numerical inversion of the optimisation problem, finishing with deterministic iterative inversion. (author)

  10. ICT for whole life optimisation of residential buildings

    Energy Technology Data Exchange (ETDEWEB)

    Haekkinen, T.; Vares, S.; Huovila, P.; Vesikari, E.; Porkka, J. (VTT Technical Research Centre of Finland, Espoo (FI)); Nilsson, L.-O.; Togeroe, AA. (Lund University (SE)); Jonsson, C.; Suber, K. (Skanska Sverige AB (SE)); Andersson, R.; Larsson, R. (Cementa, Malmoe (SE)); Nuorkivi, I. (Skanska Oyj, Helsinki (FI))

    2007-08-15

    The research project 'ICT for whole life optimisation of residential buildings' (ICTWLORB) developed and tested the whole life design and optimisation methods for residential buildings. The objective of the ICTWLORB project was to develop and implement an ICT based tool box for integrated life cycle design of residential building. ICTWLORB was performed in cooperation with Swedish and Finnish partners. The ICTWLORB project defined as a premise that an industrialised building process is characterised by two main elements: a building concept based approach and efficient information management. Building concept based approach enables (1) the product development of the end product, (2) repetition of the basic elements of the building from one project to others and (3) customisation of the end-product considering the specific needs of the case and the client. Information management enables (1) the consideration of wide spectrum of aspects including building performance, environmental aspects, life cycle costs and service life, and (2) rapid adapting of the design to the specific requirements of the case. (orig.)

  11. Optimisation of the Management of Higher Activity Waste in the UK - 13537

    Energy Technology Data Exchange (ETDEWEB)

    Walsh, Ciara; Buckley, Matthew [Nuclear Decommissioning Authority, Building 587, Curie Avenue, Harwell Oxford, Didcot, Oxfordshire, OX11 0RH (United Kingdom)

    2013-07-01

    The Upstream Optioneering project was created in the Nuclear Decommissioning Authority (UK) to support the development and implementation of significant opportunities to optimise activities across all the phases of the Higher Activity Waste management life cycle (i.e. retrieval, characterisation, conditioning, packaging, storage, transport and disposal). The objective of the Upstream Optioneering project is to work in conjunction with other functions within NDA and the waste producers to identify and deliver solutions to optimise the management of higher activity waste. Historically, optimisation may have occurred on aspects of the waste life cycle (considered here to include retrieval, conditioning, treatment, packaging, interim storage, transport to final end state, which may be geological disposal). By considering the waste life cycle as a whole, critical analysis of assumed constraints may lead to cost savings for the UK Tax Payer. For example, it may be possible to challenge the requirements for packaging wastes for disposal to deliver an optimised waste life cycle. It is likely that the challenges faced in the UK are shared in other countries. It is therefore likely that the opportunities identified may also apply elsewhere, with the potential for sharing information to enable value to be shared. (authors)

  12. Optimisation of small-scale hydropower using quality assurance methods - Preliminary project; Vorprojekt: Optimierung von Kleinwasserkraftwerken durch Qualitaetssicherung. Programm Kleinwasserkraftwerke

    Energy Technology Data Exchange (ETDEWEB)

    Hofer, S.; Staubli, T.

    2006-11-15

    This comprehensive final report for the Swiss Federal Office of Energy (SFOE) presents the results of a preliminary project that examined how quality assurance methods can be used in the optimisation of small-scale hydropower projects. The aim of the project, to use existing know-how, experience and synergies, is examined. Discrepancies in quality and their effects on production prices were determined in interviews. The paper describes best-practice guidelines for the quality assurance of small-scale hydro schemes. A flow chart describes the various steps that have to be taken in the project and realisation work. Information collected from planners and from interviews made with them are presented along with further information obtained from literature. The results of interviews concerning planning work, putting to tender and the construction stages of these hydro schemes are presented and commented on. Similarly, the operational phase of such power plant is also examined, including questions on operation and guarantees. The aims of the follow-up main project - the definition of a tool and guidelines for ensuring quality - are briefly reviewed.

  13. Optimisation of VSC-HVDC Transmission for Wind Power Plants

    DEFF Research Database (Denmark)

    Silva, Rodrigo Da

    Connection of Wind Power Plants (WPP), typically oshore, using VSCHVDC transmission is an emerging solution with many benefits compared to the traditional AC solution, especially concerning the impact on control architecture of the wind farms and the grid. The VSC-HVDC solution is likely to meet...... more stringent grid codes than a conventional AC transmission connection. The purpose of this project is to analyse how HVDC solution, considering the voltage-source converter based technology, for grid connection of large wind power plants can be designed and optimised. By optimisation, the project...... the robust control technique is applied is compared with the classical proportional-integral (PI) performance, by means of time domain simulation in a point-to-point HVDC connection. The three main parameters in the discussion are the wind power delivered from the offshore wind power plant, the variation...

  14. The new ICRP recommendations' project: A broader approach of the optimisation of radiation protection

    International Nuclear Information System (INIS)

    Lochard, J.

    2005-01-01

    In the framework of the preparation of its new recommendations ICRP has developed a new text on the optimisation of radiological protection. This text prolongs the previous publications on the principle (Publications 37 and 45) reminding the need to adopt a pragmatic approach combining quantitative techniques when they are relevant as well as know-how and past experience which are often sufficient to ensure good protection. Moreover, it aims at adapting the optimisation process to the recent evolutions of risk management with the increasing role of stakeholder involvement in the decision framing. (author)

  15. Optimising ICT effectiveness in instruction and learning: Multilevel transformation theory and a pilot project in secondary education

    NARCIS (Netherlands)

    Mooij, Ton

    2016-01-01

    Specific combinations of educational and ICT conditions including computer use may optimise learning processes, particularly for learners at risk. This position paper asks which curricular, instructional, and ICT characteristics can be expected to optimise learning processes and outcomes,and how to

  16. Optimisation in X-ray and Molecular Imaging 2015

    International Nuclear Information System (INIS)

    Baath, Magnus; Hoeschen, Christoph; Mattsson, Soeren; Mansson, Lars Gunnar

    2016-01-01

    This issue of Radiation Protection Dosimetry is based on contributions to Optimisation in X-ray and Molecular Imaging 2015 - the 4. Malmoe Conference on Medical Imaging (OXMI 2015). The conference was jointly organised by members of former and current research projects supported by the European Commission EURATOM Radiation Protection Research Programme, in cooperation with the Swedish Society for Radiation Physics. The conference brought together over 150 researchers and other professionals from hospitals, universities and industries with interests in different aspects of the optimisation of medical imaging. More than 100 presentations were given at this international gathering of medical physicists, radiologists, engineers, technicians, nurses and educational researchers. Additionally, invited talks were offered by world-renowned experts on radiation protection, spectral imaging and medical image perception, thus covering several important aspects of the generation and interpretation of medical images. The conference consisted of 13 oral sessions and a poster session, as reflected by the conference title connected by their focus on the optimisation of the use ionising radiation in medical imaging. The conference included technology-specific topics such as computed tomography and tomosynthesis, but also generic issues of interest for the optimisation of all medical imaging, such as image perception and quality assurance. Radiation protection was covered by e.g. sessions on patient dose benchmarking and occupational exposure. Technically-advanced topics such as modelling, Monte Carlo simulation, reconstruction, classification, and segmentation were seen taking advantage of recent developments of hardware and software, showing that the optimisation community is at the forefront of technology and adapts well to new requirements. These peer-reviewed proceedings, representing a continuation of a series of selected reports from meetings in the field of medical imaging

  17. Beam position optimisation for IMRT

    International Nuclear Information System (INIS)

    Holloway, L.; Hoban, P.

    2001-01-01

    Full text: The introduction of IMRT has not generally resulted in the use of optimised beam positions because to find the global solution of the problem a time consuming stochastic optimisation method must be used. Although a deterministic method may not achieve the global minimum it should achieve a superior dose distribution compared to no optimisation. This study aimed to develop and test such a method. The beam optimisation method developed relies on an iterative process to achieve the desired number of beams from a large initial number of beams. The number of beams is reduced in a 'weeding-out' process based on the total fluence which each beam delivers. The process is gradual, with only three beams removed each time (following a small number of iterations), ensuring that the reduction in beams does not dramatically affect the fluence maps of those remaining. A comparison was made between the dose distributions achieved when the beams positions were optimised in this fashion and when the beams positions were evenly distributed. The method has been shown to work quite effectively and efficiently. The Figure shows a comparison in dose distribution with optimised and non optimised beam positions for 5 beams. It can be clearly seen that there is an improvement in the dose distribution delivered to the tumour and a reduction in the dose to the critical structure with beam position optimisation. A method for beam position optimisation for use in IMRT optimisations has been developed. This method although not necessarily achieving the global minimum in beam position still achieves quite a dramatic improvement compared with no beam position optimisation and is very efficiently achieved. Copyright (2001) Australasian College of Physical Scientists and Engineers in Medicine

  18. Results of the 2010 IGSC Topical Session on Optimisation

    International Nuclear Information System (INIS)

    Bailey, Lucy

    2014-01-01

    constraints) have been met, further optimisation should be aimed at moving the project forward as efficiently as possible, and this could largely be reflected as cost optimisation. (author)

  19. Combining simulation and multi-objective optimisation for equipment quantity optimisation in container terminals

    OpenAIRE

    Lin, Zhougeng

    2013-01-01

    This thesis proposes a combination framework to integrate simulation and multi-objective optimisation (MOO) for container terminal equipment optimisation. It addresses how the strengths of simulation and multi-objective optimisation can be integrated to find high quality solutions for multiple objectives with low computational cost. Three structures for the combination framework are proposed respectively: pre-MOO structure, integrated MOO structure and post-MOO structure. The applications of ...

  20. Optimisation of the Laser Cutting Process

    DEFF Research Database (Denmark)

    Dragsted, Birgitte; Olsen, Flemmming Ove

    1996-01-01

    The problem in optimising the laser cutting process is outlined. Basic optimisation criteria and principles for adapting an optimisation method, the simplex method, are presented. The results of implementing a response function in the optimisation are discussed with respect to the quality as well...

  1. Understanding ageing in older Australians: The contribution of the Dynamic Analyses to Optimise Ageing (DYNOPTA) project to the evidenced base and policy

    Science.gov (United States)

    Anstey, Kaarin J; Bielak, Allison AM; Birrell, Carole L; Browning, Colette J; Burns, Richard A; Byles, Julie; Kiley, Kim M; Nepal, Binod; Ross, Lesley A; Steel, David; Windsor, Timothy D

    2014-01-01

    Aim To describe the Dynamic Analyses to Optimise Ageing (DYNOPTA) project and illustrate its contributions to understanding ageing through innovative methodology, and investigations on outcomes based on the project themes. DYNOPTA provides a platform and technical expertise that may be used to combine other national and international datasets. Method The DYNOPTA project has pooled and harmonized data from nine Australian longitudinal studies to create the largest available longitudinal dataset (N=50652) on ageing in Australia. Results A range of findings have resulted from the study to date, including methodological advances, prevalence rates of disease and disability, and mapping trajectories of ageing with and without increasing morbidity. DYNOPTA also forms the basis of a microsimulation model that will provide projections of future costs of disease and disability for the baby boomer cohort. Conclusion DYNOPTA contributes significantly to the Australian evidence-base on ageing to inform key social and health policy domains. PMID:22032767

  2. Optimised Renormalisation Group Flows

    CERN Document Server

    Litim, Daniel F

    2001-01-01

    Exact renormalisation group (ERG) flows interpolate between a microscopic or classical theory and the corresponding macroscopic or quantum effective theory. For most problems of physical interest, the efficiency of the ERG is constrained due to unavoidable approximations. Approximate solutions of ERG flows depend spuriously on the regularisation scheme which is determined by a regulator function. This is similar to the spurious dependence on the ultraviolet regularisation known from perturbative QCD. Providing a good control over approximated ERG flows is at the root for reliable physical predictions. We explain why the convergence of approximate solutions towards the physical theory is optimised by appropriate choices of the regulator. We study specific optimised regulators for bosonic and fermionic fields and compare the optimised ERG flows with generic ones. This is done up to second order in the derivative expansion at both vanishing and non-vanishing temperature. An optimised flow for a ``proper-time ren...

  3. Computer Based Optimisation Rutines

    DEFF Research Database (Denmark)

    Dragsted, Birgitte; Olsen, Flemmming Ove

    1996-01-01

    In this paper the need for optimisation methods for the laser cutting process has been identified as three different situations. Demands on the optimisation methods for these situations are presented, and one method for each situation is suggested. The adaptation and implementation of the methods...

  4. Optimal Optimisation in Chemometrics

    NARCIS (Netherlands)

    Hageman, J.A.

    2004-01-01

    The use of global optimisation methods is not straightforward, especially for the more difficult optimisation problems. Solutions have to be found for items such as the evaluation function, representation, step function and meta-parameters, before any useful results can be obtained. This thesis aims

  5. Optimisation of patient and staff exposure in interventional cardiology

    International Nuclear Information System (INIS)

    Padovani, R.; Malisan, M.R.; Bernardi, G.; Vano, E.; Neofotistou, V.

    2001-01-01

    The Council Directive of the European Community 97/43/Euratom (MED) deals with the health protection of individuals against dangers of ionising radiation in relation to medical exposure, and also focuses attention on some special practices (Art. 9), including interventional radiology, a technique involving high doses to the patient. The paper presents the European approach to optimisation of exposure in interventional cardiology. The DIMOND research consortium (DIMOND: Digital Imaging: Measures for Optimising Radiological Information Content and Dose) is working to develop quality criteria for cineangiographic images, to develop procedures for the classification of complexity of therapeutic and diagnostic procedures and to derive reference levels, related also to procedure complexity. DIMOND project also includes aspects of equipment characteristics and performance and content of training in radiation protection of personnel working in interventional radiology field. (author)

  6. Energy balance of the optimised CVT-hybrid-driveline

    Energy Technology Data Exchange (ETDEWEB)

    Hoehn, Bernd-Robert; Pflaum, Hermann; Lechner, Claus [Forschungsstelle fuer Zahnraeder und Getriebebau, Technische Univ. Muenchen, Garching (Germany)

    2009-07-01

    Funded by the DFG (German Research Foundation) and some industry partners like GM Powertrain Europe, ZF, EPCOS the Optimised CVT-Hybrid was developed at Technische Universitaet Muenchen in close collaboration with the industry and is currently under scientific investigation. Designed as a parallel hybrid vehicle the Optimised CVT-Hybrid combines a series-production diesel engine with a small electric motor. The core element of the driveline is a two range continuously variable transmission (i{radical}i-transmission), which is based on a chain variator. By a special shifting process without interruption of traction force the ratio range of the chain variator is used twice; thereby a wide transmission-ratio spread is achieved by low complexity. Thus the transmission provides a large pull-away ratio for the small electric motor and a fuel-efficient overdrive ratio for the ic-engine. Instead of heavy and space-consuming accumulators a small efficient package of double layer capacitors (UltraCaps) is used for electric energy and power storage. The driveline management is done by an optimised vehicle controller. Within the scope of the research project two prototype drivelines were manufactured. One driveline is integrated into an Opel Vectra Caravan and is available for investigations at the roller dynamometer and in the actual road traffic. The second hybrid driveline is assembled at the powertrain test rig of the FZG for detailed analysis of system behaviour and fuel consumption. Based on measurements of standardised driving cycles system behaviour, fuel consumption and a detailed energy balance of the Optimised CVT-Hybrid are presented. In comparison to the series-production vehicle the fuel savings are shown. (orig.)

  7. Multi-Optimisation Consensus Clustering

    Science.gov (United States)

    Li, Jian; Swift, Stephen; Liu, Xiaohui

    Ensemble Clustering has been developed to provide an alternative way of obtaining more stable and accurate clustering results. It aims to avoid the biases of individual clustering algorithms. However, it is still a challenge to develop an efficient and robust method for Ensemble Clustering. Based on an existing ensemble clustering method, Consensus Clustering (CC), this paper introduces an advanced Consensus Clustering algorithm called Multi-Optimisation Consensus Clustering (MOCC), which utilises an optimised Agreement Separation criterion and a Multi-Optimisation framework to improve the performance of CC. Fifteen different data sets are used for evaluating the performance of MOCC. The results reveal that MOCC can generate more accurate clustering results than the original CC algorithm.

  8. Particle swarm optimisation classical and quantum perspectives

    CERN Document Server

    Sun, Jun; Wu, Xiao-Jun

    2016-01-01

    IntroductionOptimisation Problems and Optimisation MethodsRandom Search TechniquesMetaheuristic MethodsSwarm IntelligenceParticle Swarm OptimisationOverviewMotivationsPSO Algorithm: Basic Concepts and the ProcedureParadigm: How to Use PSO to Solve Optimisation ProblemsSome Harder Examples Some Variants of Particle Swarm Optimisation Why Does the PSO Algorithm Need to Be Improved? Inertia and Constriction-Acceleration Techniques for PSOLocal Best ModelProbabilistic AlgorithmsOther Variants of PSO Quantum-Behaved Particle Swarm Optimisation OverviewMotivation: From Classical Dynamics to Quantum MechanicsQuantum Model: Fundamentals of QPSOQPSO AlgorithmSome Essential ApplicationsSome Variants of QPSOSummary Advanced Topics Behaviour Analysis of Individual ParticlesConvergence Analysis of the AlgorithmTime Complexity and Rate of ConvergenceParameter Selection and PerformanceSummaryIndustrial Applications Inverse Problems for Partial Differential EquationsInverse Problems for Non-Linear Dynamical SystemsOptimal De...

  9. Evolutionary programming for neutron instrument optimisation

    Energy Technology Data Exchange (ETDEWEB)

    Bentley, Phillip M. [Hahn-Meitner Institut, Glienicker Strasse 100, D-14109 Berlin (Germany)]. E-mail: phillip.bentley@hmi.de; Pappas, Catherine [Hahn-Meitner Institut, Glienicker Strasse 100, D-14109 Berlin (Germany); Habicht, Klaus [Hahn-Meitner Institut, Glienicker Strasse 100, D-14109 Berlin (Germany); Lelievre-Berna, Eddy [Institut Laue-Langevin, 6 rue Jules Horowitz, BP 156, 38042 Grenoble Cedex 9 (France)

    2006-11-15

    Virtual instruments based on Monte-Carlo techniques are now integral part of novel instrumentation development and the existing codes (McSTAS and Vitess) are extensively used to define and optimise novel instrumental concepts. Neutron spectrometers, however, involve a large number of parameters and their optimisation is often a complex and tedious procedure. Artificial intelligence algorithms are proving increasingly useful in such situations. Here, we present an automatic, reliable and scalable numerical optimisation concept based on the canonical genetic algorithm (GA). The algorithm was used to optimise the 3D magnetic field profile of the NSE spectrometer SPAN, at the HMI. We discuss the potential of the GA which combined with the existing Monte-Carlo codes (Vitess, McSTAS, etc.) leads to a very powerful tool for automated global optimisation of a general neutron scattering instrument, avoiding local optimum configurations.

  10. Evolutionary programming for neutron instrument optimisation

    International Nuclear Information System (INIS)

    Bentley, Phillip M.; Pappas, Catherine; Habicht, Klaus; Lelievre-Berna, Eddy

    2006-01-01

    Virtual instruments based on Monte-Carlo techniques are now integral part of novel instrumentation development and the existing codes (McSTAS and Vitess) are extensively used to define and optimise novel instrumental concepts. Neutron spectrometers, however, involve a large number of parameters and their optimisation is often a complex and tedious procedure. Artificial intelligence algorithms are proving increasingly useful in such situations. Here, we present an automatic, reliable and scalable numerical optimisation concept based on the canonical genetic algorithm (GA). The algorithm was used to optimise the 3D magnetic field profile of the NSE spectrometer SPAN, at the HMI. We discuss the potential of the GA which combined with the existing Monte-Carlo codes (Vitess, McSTAS, etc.) leads to a very powerful tool for automated global optimisation of a general neutron scattering instrument, avoiding local optimum configurations

  11. Topology optimised wavelength dependent splitters

    DEFF Research Database (Denmark)

    Hede, K. K.; Burgos Leon, J.; Frandsen, Lars Hagedorn

    A photonic crystal wavelength dependent splitter has been constructed by utilising topology optimisation1. The splitter has been fabricated in a silicon-on-insulator material (Fig. 1). The topology optimised wavelength dependent splitter demonstrates promising 3D FDTD simulation results....... This complex photonic crystal structure is very sensitive against small fabrication variations from the expected topology optimised design. A wavelength dependent splitter is an important basic building block for high-performance nanophotonic circuits. 1J. S. Jensen and O. Sigmund, App. Phys. Lett. 84, 2022...

  12. Optimising Magnetostatic Assemblies

    DEFF Research Database (Denmark)

    Insinga, Andrea Roberto; Smith, Anders

    theorem. This theorem formulates an energy equivalence principle with several implications concerning the optimisation of objective functionals that are linear with respect to the magnetic field. Linear functionals represent different optimisation goals, e.g. maximising a certain component of the field...... approached employing a heuristic algorithm, which led to new design concepts. Some of the procedures developed for linear objective functionals have been extended to non-linear objectives, by employing iterative techniques. Even though most the optimality results discussed in this work have been derived...

  13. Optimising Shovel-Truck Fuel Consumption using Stochastic ...

    African Journals Online (AJOL)

    Optimising the fuel consumption and truck waiting time can result in significant fuel savings. The paper demonstrates that stochastic simulation is an effective tool for optimising the utilisation of fossil-based fuels in mining and related industries. Keywords: Stochastic, Simulation Modelling, Mining, Optimisation, Shovel-Truck ...

  14. Optimisation of technical specifications using probabilistic methods

    International Nuclear Information System (INIS)

    Ericsson, G.; Knochenhauer, M.; Hultqvist, G.

    1986-01-01

    During the last few years the development of methods for modifying and optimising nuclear power plant Technical Specifications (TS) for plant operations has received increased attention. Probalistic methods in general, and the plant and system models of probabilistic safety assessment (PSA) in particular, seem to provide the most forceful tools for optimisation. This paper first gives some general comments on optimisation, identifying important parameters and then gives a description of recent Swedish experiences from the use of nuclear power plant PSA models and results for TS optimisation

  15. Turbulence optimisation in stellarator experiments

    Energy Technology Data Exchange (ETDEWEB)

    Proll, Josefine H.E. [Max-Planck/Princeton Center for Plasma Physics (Germany); Max-Planck-Institut fuer Plasmaphysik, Wendelsteinstr. 1, 17491 Greifswald (Germany); Faber, Benjamin J. [HSX Plasma Laboratory, University of Wisconsin-Madison, Madison, WI 53706 (United States); Helander, Per; Xanthopoulos, Pavlos [Max-Planck/Princeton Center for Plasma Physics (Germany); Lazerson, Samuel A.; Mynick, Harry E. [Plasma Physics Laboratory, Princeton University, P.O. Box 451 Princeton, New Jersey 08543-0451 (United States)

    2015-05-01

    Stellarators, the twisted siblings of the axisymmetric fusion experiments called tokamaks, have historically suffered from confining the heat of the plasma insufficiently compared with tokamaks and were therefore considered to be less promising candidates for a fusion reactor. This has changed, however, with the advent of stellarators in which the laminar transport is reduced to levels below that of tokamaks by shaping the magnetic field accordingly. As in tokamaks, the turbulent transport remains as the now dominant transport channel. Recent analytical theory suggests that the large configuration space of stellarators allows for an additional optimisation of the magnetic field to also reduce the turbulent transport. In this talk, the idea behind the turbulence optimisation is explained. We also present how an optimised equilibrium is obtained and how it might differ from the equilibrium field of an already existing device, and we compare experimental turbulence measurements in different configurations of the HSX stellarator in order to test the optimisation procedure.

  16. Optimised and balanced structural and system reliability of offshore wind turbines. An account

    Energy Technology Data Exchange (ETDEWEB)

    Tarp-Johansen, N.J.; Kozine, I. (Risoe National Lab., DTU, Roskilde, (DK)); Rademarkers, L. (Netherlands Energy Research Foundation (NL)); Dalsgaard Soerensen, J. (Aalborg Univ. (DK)) Ronold, K. (Det Norske Veritas (DK))

    2005-04-15

    This report gives the results of the research project 'Optimised and Uniform Safety and Reliability of Offshore Wind Turbines (an account)'. The main subject of the project has been the account of the state-of-the art of knowledge about, and/or attempts to, harmonisation of the structural reliability of wind turbines, on the one hand, and the reliability of the wind turbine's control/safety system, on the other hand. Within the project some research pointing ahead has also been conducted. (au)

  17. Layout Optimisation of Wave Energy Converter Arrays

    DEFF Research Database (Denmark)

    Ruiz, Pau Mercadé; Nava, Vincenzo; Topper, Mathew B. R.

    2017-01-01

    This paper proposes an optimisation strategy for the layout design of wave energy converter (WEC) arrays. Optimal layouts are sought so as to maximise the absorbed power given a minimum q-factor, the minimum distance between WECs, and an area of deployment. To guarantee an efficient optimisation......, a four-parameter layout description is proposed. Three different optimisation algorithms are further compared in terms of performance and computational cost. These are the covariance matrix adaptation evolution strategy (CMA), a genetic algorithm (GA) and the glowworm swarm optimisation (GSO) algorithm...

  18. Topology optimisation of natural convection problems

    DEFF Research Database (Denmark)

    Alexandersen, Joe; Aage, Niels; Andreasen, Casper Schousboe

    2014-01-01

    This paper demonstrates the application of the density-based topology optimisation approach for the design of heat sinks and micropumps based on natural convection effects. The problems are modelled under the assumptions of steady-state laminar flow using the incompressible Navier-Stokes equations...... coupled to the convection-diffusion equation through the Boussinesq approximation. In order to facilitate topology optimisation, the Brinkman approach is taken to penalise velocities inside the solid domain and the effective thermal conductivity is interpolated in order to accommodate differences...... in thermal conductivity of the solid and fluid phases. The governing equations are discretised using stabilised finite elements and topology optimisation is performed for two different problems using discrete adjoint sensitivity analysis. The study shows that topology optimisation is a viable approach...

  19. Dose optimisation in single plane interstitial brachytherapy

    DEFF Research Database (Denmark)

    Tanderup, Kari; Hellebust, Taran Paulsen; Honoré, Henriette Benedicte

    2006-01-01

    patients,       treated for recurrent rectal and cervical cancer, flexible catheters were       sutured intra-operatively to the tumour bed in areas with compromised       surgical margin. Both non-optimised, geometrically and graphically       optimised CT -based dose plans were made. The overdose index...... on the       regularity of the implant, such that the benefit of optimisation was       larger for irregular implants. OI and HI correlated strongly with target       volume limiting the usability of these parameters for comparison of dose       plans between patients. CONCLUSIONS: Dwell time optimisation significantly......BACKGROUND AND PURPOSE: Brachytherapy dose distributions can be optimised       by modulation of source dwell times. In this study dose optimisation in       single planar interstitial implants was evaluated in order to quantify the       potential benefit in patients. MATERIAL AND METHODS: In 14...

  20. An empirical study on website usability elements and how they affect search engine optimisation

    Directory of Open Access Journals (Sweden)

    Eugene B. Visser

    2011-03-01

    Full Text Available The primary objective of this research project was to identify and investigate the website usability attributes which are in contradiction with search engine optimisation elements. The secondary objective was to determine if these usability attributes affect conversion. Although the literature review identifies the contradictions, experts disagree about their existence.An experiment was conducted, whereby the conversion and/or traffic ratio results of an existing control website were compared to a usability-designed version of the control website,namely the experimental website. All optimisation elements were ignored, thus implementing only usability. The results clearly show that inclusion of the usability attributes positively affect conversion,indicating that usability is a prerequisite for effective website design. Search engine optimisation is also a prerequisite for the very reason that if a website does not rank on the first page of the search engine result page for a given keyword, then that website might as well not exist. According to this empirical work, usability is in contradiction to search engine optimisation best practices. Therefore the two need to be weighed up in terms of importance towards search engines and visitors.

  1. Topology Optimisation for Coupled Convection Problems

    DEFF Research Database (Denmark)

    Alexandersen, Joe

    This thesis deals with topology optimisation for coupled convection problems. The aim is to extend and apply topology optimisation to steady-state conjugate heat transfer problems, where the heat conduction equation governs the heat transfer in a solid and is coupled to thermal transport...... in a surrounding uid, governed by a convection-diffusion equation, where the convective velocity field is found from solving the isothermal incompressible steady-state Navier-Stokes equations. Topology optimisation is also applied to steady-state natural convection problems. The modelling is done using stabilised...... finite elements, the formulation and implementation of which was done partly during a special course as prepatory work for this thesis. The formulation is extended with a Brinkman friction term in order to facilitate the topology optimisation of fluid flow and convective cooling problems. The derived...

  2. Optimised acidification power test of yeast vitality and its use in brewing practice

    Czech Academy of Sciences Publication Activity Database

    Gabriel, P.; Dienstbier, M.; Matoulková, D.; Kosař, K.; Sigler, Karel

    2008-01-01

    Roč. 114, č. 3 (2008), s. 270-276 ISSN 0046-9750 R&D Projects: GA MŠk 1M0570 Institutional research plan: CEZ:AV0Z50200510 Keywords : acidification power * brewery practice * optimised AP test Subject RIV: EE - Microbiology, Virology Impact factor: 0.759, year: 2008

  3. Real-time optimisation of the Hoa Binh reservoir, Vietnam

    DEFF Research Database (Denmark)

    Richaud, Bertrand; Madsen, Henrik; Rosbjerg, Dan

    2011-01-01

    -time optimisation. First, the simulation-optimisation framework is applied for optimising reservoir operating rules. Secondly, real-time and forecast information is used for on-line optimisation that focuses on short-term goals, such as flood control or hydropower generation, without compromising the deviation...... in the downstream part of the Red River, and at the same time to increase hydropower generation and to save water for the dry season. The real-time optimisation procedure further improves the efficiency of the reservoir operation and enhances the flexibility for the decision-making. Finally, the quality......Multi-purpose reservoirs often have to be managed according to conflicting objectives, which requires efficient tools for trading-off the objectives. This paper proposes a multi-objective simulation-optimisation approach that couples off-line rule curve optimisation with on-line real...

  4. Optimising resource management in neurorehabilitation.

    Science.gov (United States)

    Wood, Richard M; Griffiths, Jeff D; Williams, Janet E; Brouwers, Jakko

    2014-01-01

    To date, little research has been published regarding the effective and efficient management of resources (beds and staff) in neurorehabilitation, despite being an expensive service in limited supply. To demonstrate how mathematical modelling can be used to optimise service delivery, by way of a case study at a major 21 bed neurorehabilitation unit in the UK. An automated computer program for assigning weekly treatment sessions is developed. Queue modelling is used to construct a mathematical model of the hospital in terms of referral submissions to a waiting list, admission and treatment, and ultimately discharge. This is used to analyse the impact of hypothetical strategic decisions on a variety of performance measures and costs. The project culminates in a hybridised model of these two approaches, since a relationship is found between the number of therapy hours received each week (scheduling output) and length of stay (queuing model input). The introduction of the treatment scheduling program has substantially improved timetable quality (meaning a better and fairer service to patients) and has reduced employee time expended in its creation by approximately six hours each week (freeing up time for clinical work). The queuing model has been used to assess the effect of potential strategies, such as increasing the number of beds or employing more therapists. The use of mathematical modelling has not only optimised resources in the short term, but has allowed the optimality of longer term strategic decisions to be assessed.

  5. Efficient topology optimisation of multiscale and multiphysics problems

    DEFF Research Database (Denmark)

    Alexandersen, Joe

    The aim of this Thesis is to present efficient methods for optimising high-resolution problems of a multiscale and multiphysics nature. The Thesis consists of two parts: one treating topology optimisation of microstructural details and the other treating topology optimisation of conjugate heat...

  6. Methods for Optimisation of the Laser Cutting Process

    DEFF Research Database (Denmark)

    Dragsted, Birgitte

    This thesis deals with the adaptation and implementation of various optimisation methods, in the field of experimental design, for the laser cutting process. The problem in optimising the laser cutting process has been defined and a structure for at Decision Support System (DSS......) for the optimisation of the laser cutting process has been suggested. The DSS consists of a database with the currently used and old parameter settings. Also one of the optimisation methods has been implemented in the DSS in order to facilitate the optimisation procedure for the laser operator. The Simplex Method has...... been adapted in two versions. A qualitative one, that by comparing the laser cut items optimise the process and a quantitative one that uses a weighted quality response in order to achieve a satisfactory quality and after that maximises the cutting speed thus increasing the productivity of the process...

  7. Design of optimised backstepping controller for the synchronisation ...

    Indian Academy of Sciences (India)

    Ehsan Fouladi

    2017-12-18

    Dec 18, 2017 ... for the proposed optimised method compared to PSO optimised controller or any non-optimised backstepping controller. Keywords. Colpitts oscillator; backstepping controller; chaos synchronisation; shark smell algorithm; particle .... The velocity model is based on the gradient of the objective function, tilting ...

  8. Extending Particle Swarm Optimisers with Self-Organized Criticality

    DEFF Research Database (Denmark)

    Løvbjerg, Morten; Krink, Thiemo

    2002-01-01

    Particle swarm optimisers (PSOs) show potential in function optimisation, but still have room for improvement. Self-organized criticality (SOC) can help control the PSO and add diversity. Extending the PSO with SOC seems promising reaching faster convergence and better solutions.......Particle swarm optimisers (PSOs) show potential in function optimisation, but still have room for improvement. Self-organized criticality (SOC) can help control the PSO and add diversity. Extending the PSO with SOC seems promising reaching faster convergence and better solutions....

  9. A systematic procedure to optimise dose and image quality for the measurement of inter-vertebral angles from lateral spinal projections using Cobb and superimposition methods.

    Science.gov (United States)

    Al Qaroot, Bashar; Hogg, Peter; Twiste, Martin; Howard, David

    2014-01-01

    Patients with vertebral column deformations are exposed to high risks associated with ionising radiation exposure. Risks are further increased due to the serial X-ray images that are needed to measure and asses their spinal deformation using Cobb or superimposition methods. Therefore, optimising such X-ray practice, via reducing dose whilst maintaining image quality, is a necessity. With a specific focus on lateral thoraco-lumbar images for Cobb and superimposition measurements, this paper outlines a systematic procedure to the optimisation of X-ray practice. Optimisation was conducted based on suitable image quality from minimal dose. Image quality was appraised using a visual-analogue-rating-scale, and Monte-Carlo modelling was used for dose estimation. The optimised X-ray practice was identified by imaging healthy normal-weight male adult living human volunteers. The optimised practice consisted of: anode towards the head, broad focus, no OID or grid, 80 kVp, 32 mAs and 130 cm SID. Images of suitable quality for laterally assessing spinal conditions using Cobb or superimposition measurements were produced from an effective dose of 0.05 mSv, which is 83% less than the average effective dose used in the UK for lateral thoracic/lumbar exposures. This optimisation procedure can be adopted and use for optimisation of other radiographic techniques.

  10. Methodology and Toolset for Model Verification, Hardware/Software co-simulation, Performance Optimisation and Customisable Source-code generation

    DEFF Research Database (Denmark)

    Berger, Michael Stübert; Soler, José; Yu, Hao

    2013-01-01

    The MODUS project aims to provide a pragmatic and viable solution that will allow SMEs to substantially improve their positioning in the embedded-systems development market. The MODUS tool will provide a model verification and Hardware/Software co-simulation tool (TRIAL) and a performance...... optimisation and customisable source-code generation tool (TUNE). The concept is depicted in automated modelling and optimisation of embedded-systems development. The tool will enable model verification by guiding the selection of existing open-source model verification engines, based on the automated analysis...

  11. Improving Vector Evaluated Particle Swarm Optimisation by incorporating nondominated solutions.

    Science.gov (United States)

    Lim, Kian Sheng; Ibrahim, Zuwairie; Buyamin, Salinda; Ahmad, Anita; Naim, Faradila; Ghazali, Kamarul Hawari; Mokhtar, Norrima

    2013-01-01

    The Vector Evaluated Particle Swarm Optimisation algorithm is widely used to solve multiobjective optimisation problems. This algorithm optimises one objective using a swarm of particles where their movements are guided by the best solution found by another swarm. However, the best solution of a swarm is only updated when a newly generated solution has better fitness than the best solution at the objective function optimised by that swarm, yielding poor solutions for the multiobjective optimisation problems. Thus, an improved Vector Evaluated Particle Swarm Optimisation algorithm is introduced by incorporating the nondominated solutions as the guidance for a swarm rather than using the best solution from another swarm. In this paper, the performance of improved Vector Evaluated Particle Swarm Optimisation algorithm is investigated using performance measures such as the number of nondominated solutions found, the generational distance, the spread, and the hypervolume. The results suggest that the improved Vector Evaluated Particle Swarm Optimisation algorithm has impressive performance compared with the conventional Vector Evaluated Particle Swarm Optimisation algorithm.

  12. Layout Optimisation of Wave Energy Converter Arrays

    Directory of Open Access Journals (Sweden)

    Pau Mercadé Ruiz

    2017-08-01

    Full Text Available This paper proposes an optimisation strategy for the layout design of wave energy converter (WEC arrays. Optimal layouts are sought so as to maximise the absorbed power given a minimum q-factor, the minimum distance between WECs, and an area of deployment. To guarantee an efficient optimisation, a four-parameter layout description is proposed. Three different optimisation algorithms are further compared in terms of performance and computational cost. These are the covariance matrix adaptation evolution strategy (CMA, a genetic algorithm (GA and the glowworm swarm optimisation (GSO algorithm. The results show slightly higher performances for the latter two algorithms; however, the first turns out to be significantly less computationally demanding.

  13. A comparison of forward planning and optimised inverse planning

    International Nuclear Information System (INIS)

    Oldham, Mark; Neal, Anthony; Webb, Steve

    1995-01-01

    A radiotherapy treatment plan optimisation algorithm has been applied to 48 prostate plans and the results compared with those of an experienced human planner. Twelve patients were used in the study, and a 3, 4, 6 and 8 field plan (with standard coplanar beam angles for each plan type) were optimised by both the human planner and the optimisation algorithm. The human planner 'optimised' the plan by conventional forward planning techniques. The optimisation algorithm was based on fast-simulated-annealing. 'Importance factors' assigned to different regions of the patient provide a method for controlling the algorithm, and it was found that the same values gave good results for almost all plans. The plans were compared on the basis of dose statistics and normal-tissue-complication-probability (NTCP) and tumour-control-probability (TCP). The results show that the optimisation algorithm yielded results that were at least as good as the human planner for all plan types, and on the whole slightly better. A study of the beam-weights chosen by the optimisation algorithm and the planner will be presented. The optimisation algorithm showed greater variation, in response to individual patient geometry. For simple (e.g. 3 field) plans it was found to consistently achieve slightly higher TCP and lower NTCP values. For more complicated (e.g. 8 fields) plans the optimisation also achieved slightly better results with generally less numbers of beams. The optimisation time was always ≤5 minutes; a factor of up to 20 times faster than the human planner

  14. Improving Vector Evaluated Particle Swarm Optimisation by Incorporating Nondominated Solutions

    Directory of Open Access Journals (Sweden)

    Kian Sheng Lim

    2013-01-01

    Full Text Available The Vector Evaluated Particle Swarm Optimisation algorithm is widely used to solve multiobjective optimisation problems. This algorithm optimises one objective using a swarm of particles where their movements are guided by the best solution found by another swarm. However, the best solution of a swarm is only updated when a newly generated solution has better fitness than the best solution at the objective function optimised by that swarm, yielding poor solutions for the multiobjective optimisation problems. Thus, an improved Vector Evaluated Particle Swarm Optimisation algorithm is introduced by incorporating the nondominated solutions as the guidance for a swarm rather than using the best solution from another swarm. In this paper, the performance of improved Vector Evaluated Particle Swarm Optimisation algorithm is investigated using performance measures such as the number of nondominated solutions found, the generational distance, the spread, and the hypervolume. The results suggest that the improved Vector Evaluated Particle Swarm Optimisation algorithm has impressive performance compared with the conventional Vector Evaluated Particle Swarm Optimisation algorithm.

  15. Interpretation of optimisation in the context of a disposal facility for long-lived radioactive waste

    International Nuclear Information System (INIS)

    1999-01-01

    project P3-033 contained in the following output: R and D Technical Report P259 - Interpretation of Optimisation in the Context of a disposal Facility for Long-Lived Radioactive Waste. (author)

  16. Nuclear power plant maintenance optimisation SENUF network activity

    International Nuclear Information System (INIS)

    Ahlstrand, R.; Bieth, M.; Pla, P.; Rieg, C.; Trampus, P.

    2004-01-01

    During providing scientific and technical support to TACIS and PHARE nuclear safety programs a large amount of knowledge related to Russian design reactor systems has accumulated and led to creation of a new Network concerning Nuclear Safety in Central and Eastern Europe called ''Safety of Eastern European type Nuclear Facilities'' (SENUF). SENUF contributes to bring together all stakeholders of TACIS and PHARE: beneficiaries, end users, Eastern und Western nuclear industries, and thus, to favour fruitful technical exchanges and feedback of experience. At present the main focus of SENUF is the nuclear power plant maintenance as substantial element of plant operational safety as well as life management. A Working Group has been established on plant maintenance. One of its major tasks in 2004 is to prepare a status report on advanced strategies to optimise maintenance. Optimisation projects have an interface with the plant's overall life management program. Today, almost all plants involved in SENUF network have an explicit policy to extend their service life, thus, component ageing management, modernization and refurbishment actions became much more important. A database is also under development, which intends to help sharing the available knowledge and specific equipment and tools. (orig.)

  17. Optimisation of logistics processes of energy grass collection

    Science.gov (United States)

    Bányai, Tamás.

    2010-05-01

    objective function of the optimisation is the maximisation of the profit which means the maximization of the difference between revenue and cost. The objective function trades off the income of the assigned transportation demands against the logistic costs. The constraints are the followings: (1) the free capacity of the assigned transportation resource is more than the re-quested capacity of the transportation demand; the calculated arrival time of the transportation resource to the harvesting place is not later than the requested arrival time of them; (3) the calculated arrival time of the transportation demand to the processing and production facility is not later than the requested arrival time; (4) one transportation demand is assigned to one transportation resource and one resource is assigned to one transportation resource. The decision variable of the optimisation problem is the set of scheduling variables and the assignment of resources to transportation demands. The evaluation parameters of the optimised system are the followings: total costs of the collection process; utilisation of transportation resources and warehouses; efficiency of production and/or processing facilities. However the multidimensional heuristic optimisation method is based on genetic algorithm, but the routing sequence of the optimisation works on the base of an ant colony algorithm. The optimal routes are calculated by the aid of the ant colony algorithm as a subroutine of the global optimisation method and the optimal assignment is given by the genetic algorithm. One important part of the mathematical method is the sensibility analysis of the objective function, which shows the influence rate of the different input parameters. Acknowledgements This research was implemented within the frame of the project entitled "Development and operation of the Technology and Knowledge Transfer Centre of the University of Miskolc". with support by the European Union and co-funding of the European Social

  18. An Optimisation Approach for Room Acoustics Design

    DEFF Research Database (Denmark)

    Holm-Jørgensen, Kristian; Kirkegaard, Poul Henning; Andersen, Lars

    2005-01-01

    This paper discuss on a conceptual level the value of optimisation techniques in architectural acoustics room design from a practical point of view. It is chosen to optimise one objective room acoustics design criterium estimated from the sound field inside the room. The sound field is modeled...... using the boundary element method where absorption is incorporated. An example is given where the geometry of a room is defined by four design modes. The room geometry is optimised to get a uniform sound pressure....

  19. Optimisation: how to develop stake holder involvement

    International Nuclear Information System (INIS)

    Weiss, W.

    2003-01-01

    The Precautionary Principle is an internationally recognised approach for dealing with risk situations characterised by uncertainties and potential irreversible damages. Since the late fifties, ICRP has adopted this prudent attitude because of the lack of scientific evidence concerning the existence of a threshold at low doses for stochastic effects. The 'linear, no-threshold' model and the 'optimisation of protection' principle have been developed as a pragmatic response for the management of the risk. The progress in epidemiology and radiobiology over the last decades have affirmed the initial assumption and the optimisation remains the appropriate response for the application of the precautionary principle in the context of radiological protection. The basic objective of optimisation is, for any source within the system of radiological protection, to maintain the level of exposure as low as reasonably achievable, taking into account social and economical factors. Methods tools and procedures have been developed over the last two decades to put into practice the optimisation principle with a central role given to the cost-benefit analysis as a means to determine the optimised level of protection. However, with the advancement in the implementation of the principle more emphasis was progressively given to good practice, as well as on the importance of controlling individual levels of exposure through the optimisation process. In the context of the revision of its present recommendations, the Commission is reenforcing the emphasis on protection of the individual with the adoption of an equity-based system that recognizes individual rights and a basic level of health protection. Another advancement is the role that is now recognised to 'stakeholders involvement' in the optimisation process as a mean to improve the quality of the decision aiding process for identifying and selecting protection actions considered as being accepted by all those involved. The paper

  20. Optimisation on processing parameters for minimising warpage on side arm using response surface methodology (RSM) and particle swarm optimisation (PSO)

    Science.gov (United States)

    Rayhana, N.; Fathullah, M.; Shayfull, Z.; Nasir, S. M.; Hazwan, M. H. M.; Sazli, M.; Yahya, Z. R.

    2017-09-01

    This study presents the application of optimisation method to reduce the warpage of side arm part. Autodesk Moldflow Insight software was integrated into this study to analyse the warpage. The design of Experiment (DOE) for Response Surface Methodology (RSM) was constructed and by using the equation from RSM, Particle Swarm Optimisation (PSO) was applied. The optimisation method will result in optimised processing parameters with minimum warpage. Mould temperature, melt temperature, packing pressure, packing time and cooling time was selected as the variable parameters. Parameters selection was based on most significant factor affecting warpage stated by previous researchers. The results show that warpage was improved by 28.16% for RSM and 28.17% for PSO. The warpage improvement in PSO from RSM is only by 0.01 %. Thus, the optimisation using RSM is already efficient to give the best combination parameters and optimum warpage value for side arm part. The most significant parameters affecting warpage are packing pressure.

  1. (MBO) algorithm in multi-reservoir system optimisation

    African Journals Online (AJOL)

    A comparative study of marriage in honey bees optimisation (MBO) algorithm in ... A practical application of the marriage in honey bees optimisation (MBO) ... to those of other evolutionary algorithms, such as the genetic algorithm (GA), ant ...

  2. Optimisation of Investment Resources at Small Enterprises

    Directory of Open Access Journals (Sweden)

    Shvets Iryna B.

    2014-03-01

    Full Text Available The goal of the article lies in the study of the process of optimisation of the structure of investment resources, development of criteria and stages of optimisation of volumes of investment resources for small enterprises by types of economic activity. The article characterises the process of transformation of investment resources into assets and liabilities of the balances of small enterprises and conducts calculation of the structure of sources of formation of investment resources in Ukraine at small enterprises by types of economic activity in 2011. On the basis of the conducted analysis of the structure of investment resources of small enterprises the article forms main groups of criteria of optimisation in the context of individual small enterprises by types of economic activity. The article offers an algorithm and step-by-step scheme of optimisation of investment resources at small enterprises in the form of a multi-stage process of management of investment resources in the context of increase of their mobility and rate of transformation of existing resources into investments. The prospect of further studies in this direction is development of a structural and logic scheme of optimisation of volumes of investment resources at small enterprises.

  3. Warpage optimisation on the moulded part with straight-drilled and conformal cooling channels using response surface methodology (RSM) and glowworm swarm optimisation (GSO)

    Science.gov (United States)

    Hazwan, M. H. M.; Shayfull, Z.; Sharif, S.; Nasir, S. M.; Zainal, N.

    2017-09-01

    In injection moulding process, quality and productivity are notably important and must be controlled for each product type produced. Quality is measured as the extent of warpage of moulded parts while productivity is measured as a duration of moulding cycle time. To control the quality, many researchers have introduced various of optimisation approaches which have been proven enhanced the quality of the moulded part produced. In order to improve the productivity of injection moulding process, some of researches have proposed the application of conformal cooling channels which have been proven reduced the duration of moulding cycle time. Therefore, this paper presents an application of alternative optimisation approach which is Response Surface Methodology (RSM) with Glowworm Swarm Optimisation (GSO) on the moulded part with straight-drilled and conformal cooling channels mould. This study examined the warpage condition of the moulded parts before and after optimisation work applied for both cooling channels. A front panel housing have been selected as a specimen and the performance of proposed optimisation approach have been analysed on the conventional straight-drilled cooling channels compared to the Milled Groove Square Shape (MGSS) conformal cooling channels by simulation analysis using Autodesk Moldflow Insight (AMI) 2013. Based on the results, melt temperature is the most significant factor contribute to the warpage condition and warpage have optimised by 39.1% after optimisation for straight-drilled cooling channels and cooling time is the most significant factor contribute to the warpage condition and warpage have optimised by 38.7% after optimisation for MGSS conformal cooling channels. In addition, the finding shows that the application of optimisation work on the conformal cooling channels offers the better quality and productivity of the moulded part produced.

  4. Agent-Based Decision Control—How to Appreciate Multivariate Optimisation in Architecture

    DEFF Research Database (Denmark)

    Negendahl, Kristoffer; Perkov, Thomas Holmer; Kolarik, Jakub

    2015-01-01

    , the method is applied to a multivariate optimisation problem. The aim is specifically to demonstrate optimisation for entire building energy consumption, daylight distribution and capital cost. Based on the demonstrations Moth’s ability to find local minima is discussed. It is concluded that agent-based...... in the early design stage. The main focus is to demonstrate the optimisation method, which is done in two ways. Firstly, the newly developed agent-based optimisation algorithm named Moth is tested on three different single objective search spaces. Here Moth is compared to two evolutionary algorithms. Secondly...... optimisation algorithms like Moth open up for new uses of optimisation in the early design stage. With Moth the final outcome is less dependent on pre- and post-processing, and Moth allows user intervention during optimisation. Therefore, agent-based models for optimisation such as Moth can be a powerful...

  5. A supportive architecture for CFD-based design optimisation

    Science.gov (United States)

    Li, Ni; Su, Zeya; Bi, Zhuming; Tian, Chao; Ren, Zhiming; Gong, Guanghong

    2014-03-01

    Multi-disciplinary design optimisation (MDO) is one of critical methodologies to the implementation of enterprise systems (ES). MDO requiring the analysis of fluid dynamics raises a special challenge due to its extremely intensive computation. The rapid development of computational fluid dynamic (CFD) technique has caused a rise of its applications in various fields. Especially for the exterior designs of vehicles, CFD has become one of the three main design tools comparable to analytical approaches and wind tunnel experiments. CFD-based design optimisation is an effective way to achieve the desired performance under the given constraints. However, due to the complexity of CFD, integrating with CFD analysis in an intelligent optimisation algorithm is not straightforward. It is a challenge to solve a CFD-based design problem, which is usually with high dimensions, and multiple objectives and constraints. It is desirable to have an integrated architecture for CFD-based design optimisation. However, our review on existing works has found that very few researchers have studied on the assistive tools to facilitate CFD-based design optimisation. In the paper, a multi-layer architecture and a general procedure are proposed to integrate different CFD toolsets with intelligent optimisation algorithms, parallel computing technique and other techniques for efficient computation. In the proposed architecture, the integration is performed either at the code level or data level to fully utilise the capabilities of different assistive tools. Two intelligent algorithms are developed and embedded with parallel computing. These algorithms, together with the supportive architecture, lay a solid foundation for various applications of CFD-based design optimisation. To illustrate the effectiveness of the proposed architecture and algorithms, the case studies on aerodynamic shape design of a hypersonic cruising vehicle are provided, and the result has shown that the proposed architecture

  6. Optimisation of X-ray examinations: General principles and an Irish perspective

    International Nuclear Information System (INIS)

    Matthews, Kate; Brennan, Patrick C.

    2009-01-01

    In Ireland, the European Medical Exposures Directive [Council Directive 97/43] was enacted into national law in Statutory Instrument 478 of 2002. This series of three review articles discusses the status of justification and optimisation of X-ray examinations nationally, and progress with the establishment of Irish diagnostic reference levels. In this second article, literature relating to optimisation issues arising in SI 478 of 2002 is reviewed. Optimisation associated with X-ray equipment and optimisation during day-to-day practice are considered. Optimisation proposals found in published research are summarised, and indicate the complex nature of optimisation. A paucity of current, research-based guidance documentation is identified. This is needed in order to support a range of professional staff in their practical implementation of optimisation.

  7. The apeNEXT project

    International Nuclear Information System (INIS)

    Belletti, F.; Bodin, F.; Boucaud, Ph.; Cabibbo, N.; Lonardo, A.; De Luca, S.; Lukyanov, M.; Micheli, J.; Morin, L.; Pene, O.; Pleiter, D.; Rapuano, F.; Rossetti, D.; Schifano, S.F.; Simma, H.; Tripiccione, R.; Vicini, P.

    2006-01-01

    Numerical simulations in theoretical high-energy physics (Lattice QCD) require huge computing resources. Several generations of massively parallel computers optimised for these applications have been developed within the APE (array processor experiment) project. Large prototype systems of the latest generation, apeNEXT, are currently being assembled and tested. This contribution explains how the apeNEXT architecture is optimised for Lattice QCD, provides an overview of the hardware and software of apeNEXT, and describes its new features, like the SPMD programming model and the C compiler

  8. Nuclear power plant maintenance optimisation SENUF network activity

    Energy Technology Data Exchange (ETDEWEB)

    Ahlstrand, R.; Bieth, M.; Pla, P.; Rieg, C.; Trampus, P. [Inst. for Energy, EC DG Joint Research Centre, Petten (Netherlands)

    2004-07-01

    During providing scientific and technical support to TACIS and PHARE nuclear safety programs a large amount of knowledge related to Russian design reactor systems has accumulated and led to creation of a new Network concerning Nuclear Safety in Central and Eastern Europe called ''Safety of Eastern European type Nuclear Facilities'' (SENUF). SENUF contributes to bring together all stakeholders of TACIS and PHARE: beneficiaries, end users, Eastern und Western nuclear industries, and thus, to favour fruitful technical exchanges and feedback of experience. At present the main focus of SENUF is the nuclear power plant maintenance as substantial element of plant operational safety as well as life management. A Working Group has been established on plant maintenance. One of its major tasks in 2004 is to prepare a status report on advanced strategies to optimise maintenance. Optimisation projects have an interface with the plant's overall life management program. Today, almost all plants involved in SENUF network have an explicit policy to extend their service life, thus, component ageing management, modernization and refurbishment actions became much more important. A database is also under development, which intends to help sharing the available knowledge and specific equipment and tools. (orig.)

  9. Mutual information-based LPI optimisation for radar network

    Science.gov (United States)

    Shi, Chenguang; Zhou, Jianjiang; Wang, Fei; Chen, Jun

    2015-07-01

    Radar network can offer significant performance improvement for target detection and information extraction employing spatial diversity. For a fixed number of radars, the achievable mutual information (MI) for estimating the target parameters may extend beyond a predefined threshold with full power transmission. In this paper, an effective low probability of intercept (LPI) optimisation algorithm is presented to improve LPI performance for radar network. Based on radar network system model, we first provide Schleher intercept factor for radar network as an optimisation metric for LPI performance. Then, a novel LPI optimisation algorithm is presented, where for a predefined MI threshold, Schleher intercept factor for radar network is minimised by optimising the transmission power allocation among radars in the network such that the enhanced LPI performance for radar network can be achieved. The genetic algorithm based on nonlinear programming (GA-NP) is employed to solve the resulting nonconvex and nonlinear optimisation problem. Some simulations demonstrate that the proposed algorithm is valuable and effective to improve the LPI performance for radar network.

  10. Multicriteria Optimisation in Logistics Forwarder Activities

    Directory of Open Access Journals (Sweden)

    Tanja Poletan Jugović

    2007-05-01

    Full Text Available Logistics forwarder, as organizer and planner of coordinationand integration of all the transport and logistics chains elements,uses adequate ways and methods in the process of planningand decision-making. One of these methods, analysed inthis paper, which could be used in optimisation of transportand logistics processes and activities of logistics forwarder, isthe multicriteria optimisation method. Using that method, inthis paper is suggested model of multicriteria optimisation of logisticsforwarder activities. The suggested model of optimisationis justified in keeping with method principles of multicriteriaoptimization, which is included in operation researchmethods and it represents the process of multicriteria optimizationof variants. Among many different processes of multicriteriaoptimization, PROMETHEE (Preference Ranking OrganizationMethod for Enrichment Evaluations and Promcalc& Gaia V. 3.2., computer program of multicriteria programming,which is based on the mentioned process, were used.

  11. Optimisation by hierarchical search

    Science.gov (United States)

    Zintchenko, Ilia; Hastings, Matthew; Troyer, Matthias

    2015-03-01

    Finding optimal values for a set of variables relative to a cost function gives rise to some of the hardest problems in physics, computer science and applied mathematics. Although often very simple in their formulation, these problems have a complex cost function landscape which prevents currently known algorithms from efficiently finding the global optimum. Countless techniques have been proposed to partially circumvent this problem, but an efficient method is yet to be found. We present a heuristic, general purpose approach to potentially improve the performance of conventional algorithms or special purpose hardware devices by optimising groups of variables in a hierarchical way. We apply this approach to problems in combinatorial optimisation, machine learning and other fields.

  12. Modified cuckoo search: A new gradient free optimisation algorithm

    International Nuclear Information System (INIS)

    Walton, S.; Hassan, O.; Morgan, K.; Brown, M.R.

    2011-01-01

    Highlights: → Modified cuckoo search (MCS) is a new gradient free optimisation algorithm. → MCS shows a high convergence rate, able to outperform other optimisers. → MCS is particularly strong at high dimension objective functions. → MCS performs well when applied to engineering problems. - Abstract: A new robust optimisation algorithm, which can be regarded as a modification of the recently developed cuckoo search, is presented. The modification involves the addition of information exchange between the top eggs, or the best solutions. Standard optimisation benchmarking functions are used to test the effects of these modifications and it is demonstrated that, in most cases, the modified cuckoo search performs as well as, or better than, the standard cuckoo search, a particle swarm optimiser, and a differential evolution strategy. In particular the modified cuckoo search shows a high convergence rate to the true global minimum even at high numbers of dimensions.

  13. SPS batch spacing optimisation

    CERN Document Server

    Velotti, F M; Carlier, E; Goddard, B; Kain, V; Kotzian, G

    2017-01-01

    Until 2015, the LHC filling schemes used the batch spac-ing as specified in the LHC design report. The maximumnumber of bunches injectable in the LHC directly dependson the batch spacing at injection in the SPS and hence onthe MKP rise time.As part of the LHC Injectors Upgrade project for LHCheavy ions, a reduction of the batch spacing is needed. In thisdirection, studies to approach the MKP design rise time of150ns(2-98%) have been carried out. These measurementsgave clear indications that such optimisation, and beyond,could be done also for higher injection momentum beams,where the additional slower MKP (MKP-L) is needed.After the successful results from 2015 SPS batch spacingoptimisation for the Pb-Pb run [1], the same concept wasthought to be used also for proton beams. In fact, thanksto the SPS transverse feed back, it was already observedthat lower batch spacing than the design one (225ns) couldbe achieved. For the 2016 p-Pb run, a batch spacing of200nsfor the proton beam with100nsbunch spacing wasreque...

  14. Optimised performance of industrial high resolution computerised tomography

    International Nuclear Information System (INIS)

    Maangaard, M.

    2000-01-01

    -sensitivity/noise, density-sensitivity/noise, and mass attenuation-sensitivity/noise. With these measures, a method is presented that finds the optimal equipment settings, where no improvement can be made without worsening at least one other sensitivity/noise ratio. This thesis includes modelling and verification of the sharpness of the CT system in terms of the modulation transfer function, MTF. Together with the limiting perception factor and the maximised SNR the detectability limits for any specific contrasting detail in the centre of a cylindrical sample can be determined. It is also demonstrated that the model can be used to suppress beam hardening when collecting CT-data. When homogeneous samples are imaged, the model can in addition be used to make post-processing corrections for suppressing the beam hardening artefacts. Wavelet-based local tomography has been found to produce images with good accuracy from projection data only from a small region in a sample. This technique is demonstrated on thermal barrier coatings, which contain internal cracks. With optimised equipment settings and geometrical magnification of a region in the sample, wavelet-based local tomography produced high-resolution images of excellent quality. The increased resolution reveals features in the microstructure that cannot be resolved with traditional CT. This technique will be a useful tool for characterisation of the microstructure in advanced materials

  15. A methodological approach to the design of optimising control strategies for sewer systems

    DEFF Research Database (Denmark)

    Mollerup, Ane Loft; Mikkelsen, Peter Steen; Sin, Gürkan

    2016-01-01

    This study focuses on designing an optimisation based control for sewer system in a methodological way and linking itto a regulatory control. Optimisation based design is found to depend on proper choice of a model, formulation of objective function and tuning of optimisation parameters. Accordin......This study focuses on designing an optimisation based control for sewer system in a methodological way and linking itto a regulatory control. Optimisation based design is found to depend on proper choice of a model, formulation of objective function and tuning of optimisation parameters....... Accordingly, two novel optimisation configurations are developed, where the optimisation either acts on the actuators or acts on the regulatory control layer. These two optimisation designs are evaluated on a sub-catchment of the sewer system in Copenhagen, and found to perform better than the existing...

  16. Optimising costs in WLCG operations

    CERN Document Server

    Pradillo, Mar; Flix, Josep; Forti, Alessandra; Sciabà, Andrea

    2015-01-01

    The Worldwide LHC Computing Grid project (WLCG) provides the computing and storage resources required by the LHC collaborations to store, process and analyse the 50 Petabytes of data annually generated by the LHC. The WLCG operations are coordinated by a distributed team of managers and experts and performed by people at all participating sites and from all the experiments. Several improvements in the WLCG infrastructure have been implemented during the first long LHC shutdown to prepare for the increasing needs of the experiments during Run2 and beyond. However, constraints in funding will affect not only the computing resources but also the available effort for operations. This paper presents the results of a detailed investigation on the allocation of the effort in the different areas of WLCG operations, identifies the most important sources of inefficiency and proposes viable strategies for optimising the operational cost, taking into account the current trends in the evolution of the computing infrastruc...

  17. Spatial-structural interaction and strain energy structural optimisation

    NARCIS (Netherlands)

    Hofmeyer, H.; Davila Delgado, J.M.; Borrmann, A.; Geyer, P.; Rafiq, Y.; Wilde, de P.

    2012-01-01

    A research engine iteratively transforms spatial designs into structural designs and vice versa. Furthermore, spatial and structural designs are optimised. It is suggested to optimise a structural design by evaluating the strain energy of its elements and by then removing, adding, or changing the

  18. Energy Savings from Optimised In-Field Route Planning for Agricultural Machinery

    Directory of Open Access Journals (Sweden)

    Efthymios Rodias

    2017-10-01

    Full Text Available Various types of sensors technologies, such as machine vision and global positioning system (GPS have been implemented in navigation of agricultural vehicles. Automated navigation systems have proved the potential for the execution of optimised route plans for field area coverage. This paper presents an assessment of the reduction of the energy requirements derived from the implementation of optimised field area coverage planning. The assessment regards the analysis of the energy requirements and the comparison between the non-optimised and optimised plans for field area coverage in the whole sequence of operations required in two different cropping systems: Miscanthus and Switchgrass production. An algorithmic approach for the simulation of the executed field operations by following both non-optimised and optimised field-work patterns was developed. As a result, the corresponding time requirements were estimated as the basis of the subsequent energy cost analysis. Based on the results, the optimised routes reduce the fuel energy consumption up to 8%, the embodied energy consumption up to 7%, and the total energy consumption from 3% up to 8%.

  19. Profile control studies for JET optimised shear regime

    Energy Technology Data Exchange (ETDEWEB)

    Litaudon, X.; Becoulet, A.; Eriksson, L.G.; Fuchs, V.; Huysmans, G.; How, J.; Moreau, D.; Rochard, F.; Tresset, G.; Zwingmann, W. [Association Euratom-CEA, CEA/Cadarache, Dept. de Recherches sur la Fusion Controlee, DRFC, 13 - Saint-Paul-lez-Durance (France); Bayetti, P.; Joffrin, E.; Maget, P.; Mayorat, M.L.; Mazon, D.; Sarazin, Y. [JET Abingdon, Oxfordshire (United Kingdom); Voitsekhovitch, I. [Universite de Provence, LPIIM, Aix-Marseille 1, 13 (France)

    2000-03-01

    This report summarises the profile control studies, i.e. preparation and analysis of JET Optimised Shear plasmas, carried out during the year 1999 within the framework of the Task-Agreement (RF/CEA/02) between JET and the Association Euratom-CEA/Cadarache. We report on our participation in the preparation of the JET Optimised Shear experiments together with their comprehensive analyses and the modelling. Emphasis is put on the various aspects of pressure profile control (core and edge pressure) together with detailed studies of current profile control by non-inductive means, in the prospects of achieving steady, high performance, Optimised Shear plasmas. (authors)

  20. Optimisation of radiation protection

    International Nuclear Information System (INIS)

    1988-01-01

    Optimisation of radiation protection is one of the key elements in the current radiation protection philosophy. The present system of dose limitation was issued in 1977 by the International Commission on Radiological Protection (ICRP) and includes, in addition to the requirements of justification of practices and limitation of individual doses, the requirement that all exposures be kept as low as is reasonably achievable, taking social and economic factors into account. This last principle is usually referred to as optimisation of radiation protection, or the ALARA principle. The NEA Committee on Radiation Protection and Public Health (CRPPH) organised an ad hoc meeting, in liaison with the NEA committees on the safety of nuclear installations and radioactive waste management. Separate abstracts were prepared for individual papers presented at the meeting

  1. Development of superconducting crossbar-H-mode cavities for proton and ion accelerators

    Directory of Open Access Journals (Sweden)

    F. Dziuba

    2010-04-01

    Full Text Available The crossbar-H-mode (CH structure is the first superconducting multicell drift tube cavity for the low and medium energy range operated in the H_{21} mode. Because of the large energy gain per cavity, which leads to high real estate gradients, it is an excellent candidate for the efficient acceleration in high power proton and ion accelerators with fixed velocity profile. A prototype cavity has been developed and tested successfully with a gradient of 7  MV/m. A few new superconducting CH cavities with improved geometries for different high power applications are under development at present. One cavity (f=325  MHz, β=0.16, seven cells is currently under construction and studied with respect to a possible upgrade option for the GSI UNILAC. Another cavity (f=217  MHz, β=0.059, 15 cells is designed for a cw operated energy variable heavy ion linac application. Furthermore, the EUROTRANS project (European research program for the transmutation of high level nuclear waste in an accelerator driven system, 600 MeV protons, 352 MHz is one of many possible applications for this kind of superconducting rf cavity. In this context a layout of the 17 MeV EUROTRANS injector containing four superconducting CH cavities was proposed by the Institute for Applied Physics (IAP Frankfurt. The status of the cavity development related to the EUROTRANS injector is presented.

  2. TEM turbulence optimisation in stellarators

    Science.gov (United States)

    Proll, J. H. E.; Mynick, H. E.; Xanthopoulos, P.; Lazerson, S. A.; Faber, B. J.

    2016-01-01

    With the advent of neoclassically optimised stellarators, optimising stellarators for turbulent transport is an important next step. The reduction of ion-temperature-gradient-driven turbulence has been achieved via shaping of the magnetic field, and the reduction of trapped-electron mode (TEM) turbulence is addressed in the present paper. Recent analytical and numerical findings suggest TEMs are stabilised when a large fraction of trapped particles experiences favourable bounce-averaged curvature. This is the case for example in Wendelstein 7-X (Beidler et al 1990 Fusion Technol. 17 148) and other Helias-type stellarators. Using this knowledge, a proxy function was designed to estimate the TEM dynamics, allowing optimal configurations for TEM stability to be determined with the STELLOPT (Spong et al 2001 Nucl. Fusion 41 711) code without extensive turbulence simulations. A first proof-of-principle optimised equilibrium stemming from the TEM-dominated stellarator experiment HSX (Anderson et al 1995 Fusion Technol. 27 273) is presented for which a reduction of the linear growth rates is achieved over a broad range of the operational parameter space. As an important consequence of this property, the turbulent heat flux levels are reduced compared with the initial configuration.

  3. Analysis and optimisation of heterogeneous real-time embedded systems

    DEFF Research Database (Denmark)

    Pop, Paul; Eles, Petru; Peng, Zebo

    2005-01-01

    . The success of such new design methods depends on the availability of analysis and optimisation techniques. Analysis and optimisation techniques for heterogeneous real-time embedded systems are presented in the paper. The authors address in more detail a particular class of such systems called multi...... of application messages to frames. Optimisation heuristics for frame packing aimed at producing a schedulable system are presented. Extensive experiments and a real-life example show the efficiency of the frame-packing approach....

  4. Analysis and optimisation of heterogeneous real-time embedded systems

    DEFF Research Database (Denmark)

    Pop, Paul; Eles, Petru; Peng, Zebo

    2006-01-01

    . The success of such new design methods depends on the availability of analysis and optimisation techniques. Analysis and optimisation techniques for heterogeneous real-time embedded systems are presented in the paper. The authors address in more detail a particular class of such systems called multi...... of application messages to frames. Optimisation heuristics for frame packing aimed at producing a schedulable system are presented. Extensive experiments and a real-life example show the efficiency of the frame-packing approach....

  5. Isogeometric Analysis and Shape Optimisation

    DEFF Research Database (Denmark)

    Gravesen, Jens; Evgrafov, Anton; Gersborg, Allan Roulund

    of the whole domain. So in every optimisation cycle we need to extend a parametrisation of the boundary of a domain to the whole domain. It has to be fast in order not to slow the optimisation down but it also has to be robust and give a parametrisation of high quality. These are conflicting requirements so we...... will explain how the validity of a parametrisation can be checked and we will describe various ways to parametrise a domain. We will in particular study the Winslow functional which turns out to have some desirable properties. Other problems we touch upon is clustering of boundary control points (design...

  6. Time varying acceleration coefficients particle swarm optimisation (TVACPSO): A new optimisation algorithm for estimating parameters of PV cells and modules

    International Nuclear Information System (INIS)

    Jordehi, Ahmad Rezaee

    2016-01-01

    Highlights: • A modified PSO has been proposed for parameter estimation of PV cells and modules. • In the proposed modified PSO, acceleration coefficients are changed during run. • The proposed modified PSO mitigates premature convergence problem. • Parameter estimation problem has been solved for both PV cells and PV modules. • The results show that proposed PSO outperforms other state of the art algorithms. - Abstract: Estimating circuit model parameters of PV cells/modules represents a challenging problem. PV cell/module parameter estimation problem is typically translated into an optimisation problem and is solved by metaheuristic optimisation problems. Particle swarm optimisation (PSO) is considered as a popular and well-established optimisation algorithm. Despite all its advantages, PSO suffers from premature convergence problem meaning that it may get trapped in local optima. Personal and social acceleration coefficients are two control parameters that, due to their effect on explorative and exploitative capabilities, play important roles in computational behavior of PSO. In this paper, in an attempt toward premature convergence mitigation in PSO, its personal acceleration coefficient is decreased during the course of run, while its social acceleration coefficient is increased. In this way, an appropriate tradeoff between explorative and exploitative capabilities of PSO is established during the course of run and premature convergence problem is significantly mitigated. The results vividly show that in parameter estimation of PV cells and modules, the proposed time varying acceleration coefficients PSO (TVACPSO) offers more accurate parameters than conventional PSO, teaching learning-based optimisation (TLBO) algorithm, imperialistic competitive algorithm (ICA), grey wolf optimisation (GWO), water cycle algorithm (WCA), pattern search (PS) and Newton algorithm. For validation of the proposed methodology, parameter estimation has been done both for

  7. Share-of-Surplus Product Line Optimisation with Price Levels

    Directory of Open Access Journals (Sweden)

    X. G. Luo

    2014-01-01

    Full Text Available Kraus and Yano (2003 established the share-of-surplus product line optimisation model and developed a heuristic procedure for this nonlinear mixed-integer optimisation model. In their model, price of a product is defined as a continuous decision variable. However, because product line optimisation is a planning process in the early stage of product development, pricing decisions usually are not very precise. In this research, a nonlinear integer programming share-of-surplus product line optimization model that allows the selection of candidate price levels for products is established. The model is further transformed into an equivalent linear mixed-integer optimisation model by applying linearisation techniques. Experimental results in different market scenarios show that the computation time of the transformed model is much less than that of the original model.

  8. Multiobjective optimisation of bogie suspension to boost speed on curves

    Science.gov (United States)

    Milad Mousavi-Bideleh, Seyed; Berbyuk, Viktor

    2016-01-01

    To improve safety and maximum admissible speed on different operational scenarios, multiobjective optimisation of bogie suspension components of a one-car railway vehicle model is considered. The vehicle model has 50 degrees of freedom and is developed in multibody dynamics software SIMPACK. Track shift force, running stability, and risk of derailment are selected as safety objective functions. The improved maximum admissible speeds of the vehicle on curves are determined based on the track plane accelerations up to 1.5 m/s2. To attenuate the number of design parameters for optimisation and improve the computational efficiency, a global sensitivity analysis is accomplished using the multiplicative dimensional reduction method (M-DRM). A multistep optimisation routine based on genetic algorithm (GA) and MATLAB/SIMPACK co-simulation is executed at three levels. The bogie conventional secondary and primary suspension components are chosen as the design parameters in the first two steps, respectively. In the last step semi-active suspension is in focus. The input electrical current to magnetorheological yaw dampers is optimised to guarantee an appropriate safety level. Semi-active controllers are also applied and the respective effects on bogie dynamics are explored. The safety Pareto optimised results are compared with those associated with in-service values. The global sensitivity analysis and multistep approach significantly reduced the number of design parameters and improved the computational efficiency of the optimisation. Furthermore, using the optimised values of design parameters give the possibility to run the vehicle up to 13% faster on curves while a satisfactory safety level is guaranteed. The results obtained can be used in Pareto optimisation and active bogie suspension design problems.

  9. An empirical study on website usability elements and how they affect search engine optimisation

    OpenAIRE

    Eugene B. Visser; Melius Weideman

    2011-01-01

    The primary objective of this research project was to identify and investigate the website usability attributes which are in contradiction with search engine optimisation elements. The secondary objective was to determine if these usability attributes affect conversion. Although the literature review identifies the contradictions, experts disagree about their existence.An experiment was conducted, whereby the conversion and/or traffic ratio results of an existing control website were compared...

  10. Energy efficient maintenance. Project report; Energioptimerende vedligehold. Projektrapport

    Energy Technology Data Exchange (ETDEWEB)

    Bjerg, J. (Center for Drift og Vedligehold, Frederici (Denmark)); Dam Wied, M.; Skjershede Nielsen, P.; Holt, J. (NRGi Raadgivning A/S, Aarhus (Denmark)); Dam, M. (Energi Horsens, Horsens (Denmark)); Holk Lauridsen, V. (Teknologisk Institut, Energieffektivisering og Ventilation, Taastrup (Denmark))

    2010-03-15

    Together with four case companies, the project developed and tested a model for energy-efficient maintenance. In each of the companies, the model was adjusted through a cooperation process aiming at combining energy optimisation and maintenance as part of specific production optimisation. When correctly planned, energy-efficient maintenance is interesting for all companies. An overall solution was made, which can facilitate major energy savings and production efficiency improvement. (LN)

  11. Establishing Local Reference Dose Values and Optimisation Strategies

    International Nuclear Information System (INIS)

    Connolly, P.; Moores, B.M.

    2000-01-01

    The revised EC Patient Directive 97/43 EURATOM introduces the concepts of clinical audit, diagnostic reference levels and optimisation of radiation protection in diagnostic radiology. The application of reference dose levels in practice involves the establishment of reference dose values as actual measurable operational quantities. These values should then form part of an ongoing optimisation and audit programme against which routine performance can be compared. The CEC Quality Criteria for Radiographic Images provides guidance reference dose values against which local performance can be compared. In many cases these values can be improved upon quite considerably. This paper presents the results of a local initiative in the North West of the UK aimed at establishing local reference dose values for a number of major hospital sites. The purpose of this initiative is to establish a foundation for both optimisation strategies and clinical audit as an ongoing and routine practice. The paper presents results from an ongoing trial involving patient dose measurements for several radiological examinations upon the sites. The results of an attempt to establish local reference dose values from measured dose values and to employ them in optimisation strategies are presented. In particular emphasis is placed on the routine quality control programmes necessary to underpin this strategy including the effective data management of results from such programmes and how they can be employed to optimisation practices. (author)

  12. For Time-Continuous Optimisation

    DEFF Research Database (Denmark)

    Heinrich, Mary Katherine; Ayres, Phil

    2016-01-01

    Strategies for optimisation in design normatively assume an artefact end-point, disallowing continuous architecture that engages living systems, dynamic behaviour, and complex systems. In our Flora Robotica investigations of symbiotic plant-robot bio-hybrids, we re- quire computational tools...

  13. Iranian ethylene project

    Energy Technology Data Exchange (ETDEWEB)

    Laugier, J.P.; Handels, J.W.; Overwater, J.; Zielinski, E. [Technip-Coflexip (Iran)

    2002-04-01

    The authors discuss design optimization plans for the world's largest olefins project in Iran. The design has been optimised for both low investment cost and low operating cost. The ways in which this was achieved are outlined under the headings: furnaces, fractionation, hydrogenation, cooling medium and steam system. (UK)

  14. User perspectives in public transport timetable optimisation

    DEFF Research Database (Denmark)

    Jensen, Jens Parbo; Nielsen, Otto Anker; Prato, Carlo Giacomo

    2014-01-01

    The present paper deals with timetable optimisation from the perspective of minimising the waiting time experienced by passengers when transferring either to or from a bus. Due to its inherent complexity, this bi-level minimisation problem is extremely difficult to solve mathematically, since tim...... on the large-scale public transport network in Denmark. The timetable optimisation approach yielded a yearly reduction in weighted waiting time equivalent to approximately 45 million Danish kroner (9 million USD)....

  15. Optimising of Steel Fiber Reinforced Concrete Mix Design | Beddar ...

    African Journals Online (AJOL)

    Optimising of Steel Fiber Reinforced Concrete Mix Design. ... as a result of the loss of mixture workability that will be translated into a difficult concrete casting in site. ... An experimental study of an optimisation method of fibres in reinforced ...

  16. Expect systems and optimisation in process control

    Energy Technology Data Exchange (ETDEWEB)

    Mamdani, A.; Efstathiou, J. (eds.)

    1986-01-01

    This report brings together recent developments both in expert systems and in optimisation, and deals with current applications in industry. Part One is concerned with Artificial Intellegence in planning and scheduling and with rule-based control implementation. The tasks of control maintenance, rescheduling and planning are each discussed in relation to new theoretical developments, techniques available, and sample applications. Part Two covers model based control techniques in which the control decisions are used in a computer model of the process. Fault diagnosis, maintenance and trouble-shooting are just some of the activities covered. Part Three contains case studies of projects currently in progress, giving details of the software available and the likely future trends. One of these, on qualitative plant modelling as a basis for knowledge-based operator aids in nuclear power stations is indexed separately.

  17. Expert systems and optimisation in process control

    International Nuclear Information System (INIS)

    Mamdani, A.; Efstathiou, J.

    1986-01-01

    This report brings together recent developments both in expert systems and in optimisation, and deals with current applications in industry. Part One is concerned with Artificial Intellegence in planning and scheduling and with rule-based control implementation. The tasks of control maintenance, rescheduling and planning are each discussed in relation to new theoretical developments, techniques available, and sample applications. Part Two covers model based control techniques in which the control decisions are used in a computer model of the process. Fault diagnosis, maintenance and trouble-shooting are just some of the activities covered. Part Three contains case studies of projects currently in progress, giving details of the software available and the likely future trends. One of these, on qualitative plant modelling as a basis for knowledge-based operator aids in nuclear power stations is indexed separately. (author)

  18. Value Chain Optimisation of Biogas Production

    DEFF Research Database (Denmark)

    Jensen, Ida Græsted

    economically feasible. In this PhD thesis, the focus is to create models for investigating the profitability of biogas projects by: 1) including the whole value chain in a mathematical model and considering mass and energy changes on the upstream part of the chain; and 2) including profit allocation in a value......, the costs on the biogas plant has been included in the model using economy of scale. For the second point, a mathematical model considering profit allocation was developed applying three allocation mechanisms. This mathematical model can be applied as a second step after the value chain optimisation. After...... in the energy systems model to find the optimal end use of each type of gas and fuel. The main contributions of this thesis are the methods developed on plant level. Both the mathematical model for the value chain and the profit allocation model can be generalised and used in other industries where mass...

  19. Methodological principles for optimising functional MRI experiments

    International Nuclear Information System (INIS)

    Wuestenberg, T.; Giesel, F.L.; Strasburger, H.

    2005-01-01

    Functional magnetic resonance imaging (fMRI) is one of the most common methods for localising neuronal activity in the brain. Even though the sensitivity of fMRI is comparatively low, the optimisation of certain experimental parameters allows obtaining reliable results. In this article, approaches for optimising the experimental design, imaging parameters and analytic strategies will be discussed. Clinical neuroscientists and interested physicians will receive practical rules of thumb for improving the efficiency of brain imaging experiments. (orig.) [de

  20. DACIA LOGAN LIVE AXLE OPTIMISATION USING COMPUTER GRAPHICS

    Directory of Open Access Journals (Sweden)

    KIRALY Andrei

    2017-05-01

    Full Text Available The paper presents some contributions to the calculus and optimisation of a live axle used at Dacia Logan using computer graphics software for creating the model and afterwards using FEA evaluation to determine the effectiveness of the optimisation. Thus using specialized computer software, a simulation is made and the results were compared to the measured real prototype.

  1. Mesh dependence in PDE-constrained optimisation an application in tidal turbine array layouts

    CERN Document Server

    Schwedes, Tobias; Funke, Simon W; Piggott, Matthew D

    2017-01-01

    This book provides an introduction to PDE-constrained optimisation using finite elements and the adjoint approach. The practical impact of the mathematical insights presented here are demonstrated using the realistic scenario of the optimal placement of marine power turbines, thereby illustrating the real-world relevance of best-practice Hilbert space aware approaches to PDE-constrained optimisation problems. Many optimisation problems that arise in a real-world context are constrained by partial differential equations (PDEs). That is, the system whose configuration is to be optimised follows physical laws given by PDEs. This book describes general Hilbert space formulations of optimisation algorithms, thereby facilitating optimisations whose controls are functions of space. It demonstrates the importance of methods that respect the Hilbert space structure of the problem by analysing the mathematical drawbacks of failing to do so. The approaches considered are illustrated using the optimisation problem arisin...

  2. CLIC crab cavity design optimisation for maximum luminosity

    Energy Technology Data Exchange (ETDEWEB)

    Dexter, A.C., E-mail: a.dexter@lancaster.ac.uk [Lancaster University, Lancaster, LA1 4YR (United Kingdom); Cockcroft Institute, Daresbury, Warrington, WA4 4AD (United Kingdom); Burt, G.; Ambattu, P.K. [Lancaster University, Lancaster, LA1 4YR (United Kingdom); Cockcroft Institute, Daresbury, Warrington, WA4 4AD (United Kingdom); Dolgashev, V. [SLAC, Menlo Park, CA 94025 (United States); Jones, R. [University of Manchester, Manchester, M13 9PL (United Kingdom)

    2011-11-21

    The bunch size and crossing angle planned for CERN's compact linear collider CLIC dictate that crab cavities on opposing linacs will be needed to rotate bunches of particles into alignment at the interaction point if the desired luminosity is to be achieved. Wakefield effects, RF phase errors between crab cavities on opposing linacs and unpredictable beam loading can each act to reduce luminosity below that anticipated for bunches colliding in perfect alignment. Unlike acceleration cavities, which are normally optimised for gradient, crab cavities must be optimised primarily for luminosity. Accepting the crab cavity technology choice of a 12 GHz, normal conducting, travelling wave structure as explained in the text, this paper develops an analytical approach to optimise cell number and iris diameter.

  3. A conceptual optimisation strategy for radiography in a digital environment

    International Nuclear Information System (INIS)

    Baath, M.; Haakansson, M.; Hansson, J.; Maansson, L. G.

    2005-01-01

    Using a completely digital environment for the entire imaging process leads to new possibilities for optimisation of radiography since many restrictions of screen/film systems, such as the small dynamic range and the lack of possibilities for image processing, do not apply any longer. However, at the same time these new possibilities lead to a more complicated optimisation process, since more freedom is given to alter parameters. This paper focuses on describing an optimisation strategy that concentrates on taking advantage of the conceptual differences between digital systems and screen/film systems. The strategy can be summarised as: (a) always include the anatomical background during the optimisation, (b) perform all comparisons at a constant effective dose and (c) separate the image display stage from the image collection stage. A three-step process is proposed where the optimal setting of the technique parameters is determined at first, followed by an optimisation of the image processing. In the final step the optimal dose level - given the optimal settings of the image collection and image display stages - is determined. (authors)

  4. Heat pumps: planning, optimisation, operation and maintenance; Waermepumpen. Planung - Optimierung - Betrieb - Wartung

    Energy Technology Data Exchange (ETDEWEB)

    Kunz, P. [Kunz-Beratungen, Dietlikon (Switzerland); Afjei, T. [Fachhochschule Nordwestschweiz, Institut fuer Energie am Bau, Muttenz (Switzerland); Betschart, W.; Prochaska, V. [Hochschule Luzern, Technik und Architektur, Horw (Switzerland); Hubacher, P. [Hubacher Engineering, Engelburg (Switzerland); Loehrer, R. [Scheco AG, Winterthur (Switzerland); Mueller, A. [Mueller und Pletscher AG, Winterthur (Switzerland)

    2008-01-15

    This handbook issued by the Swiss Federal Office of Energy (SFOE) in co-operation with a trade publication takes a look at the planning, optimisation, operation and maintenance of heat pumps. First of all, the basics of heat pump technology, heat pump components and refrigerants are discussed. Then, heat sources and heat distribution are looked at, followed by chapters on the integration of heat pumps into heating systems and noise protection topics. The definition of projects, commissioning and operation of heat pump systems are then discussed. Examples of installations round off the handbook.

  5. Optimisation of a novel trailing edge concept for a high lift device

    CSIR Research Space (South Africa)

    Botha, JDM

    2014-09-01

    Full Text Available A novel concept (referred to as the flap extension) is implemented on the leading edge of the flap of a three element high lift device. The concept is optimised using two optimisation approaches based on Genetic Algorithm optimisations. A zero order...

  6. Distributed optimisation problem with communication delay and external disturbance

    Science.gov (United States)

    Tran, Ngoc-Tu; Xiao, Jiang-Wen; Wang, Yan-Wu; Yang, Wu

    2017-12-01

    This paper investigates the distributed optimisation problem for the multi-agent systems (MASs) with the simultaneous presence of external disturbance and the communication delay. To solve this problem, a two-step design scheme is introduced. In the first step, based on the internal model principle, the internal model term is constructed to compensate the disturbance asymptotically. In the second step, a distributed optimisation algorithm is designed to solve the distributed optimisation problem based on the MASs with the simultaneous presence of disturbance and communication delay. Moreover, in the proposed algorithm, each agent interacts with its neighbours through the connected topology and the delay occurs during the information exchange. By utilising Lyapunov-Krasovskii functional, the delay-dependent conditions are derived for both slowly and fast time-varying delay, respectively, to ensure the convergence of the algorithm to the optimal solution of the optimisation problem. Several numerical simulation examples are provided to illustrate the effectiveness of the theoretical results.

  7. A Bayesian Approach for Sensor Optimisation in Impact Identification

    Directory of Open Access Journals (Sweden)

    Vincenzo Mallardo

    2016-11-01

    Full Text Available This paper presents a Bayesian approach for optimizing the position of sensors aimed at impact identification in composite structures under operational conditions. The uncertainty in the sensor data has been represented by statistical distributions of the recorded signals. An optimisation strategy based on the genetic algorithm is proposed to find the best sensor combination aimed at locating impacts on composite structures. A Bayesian-based objective function is adopted in the optimisation procedure as an indicator of the performance of meta-models developed for different sensor combinations to locate various impact events. To represent a real structure under operational load and to increase the reliability of the Structural Health Monitoring (SHM system, the probability of malfunctioning sensors is included in the optimisation. The reliability and the robustness of the procedure is tested with experimental and numerical examples. Finally, the proposed optimisation algorithm is applied to a composite stiffened panel for both the uniform and non-uniform probability of impact occurrence.

  8. European Europart integrated project on actinide partitioning

    International Nuclear Information System (INIS)

    Madic, C.; Hudson, M.J.

    2005-01-01

    This poster presents the objectives of EUROPART, a scientific integrated project between 24 European partners, mostly funded by the European Community within the FP6. EUROPART aims at developing chemical partitioning processes for the so-called minor actinides (MA) contained in nuclear wastes, i.e. from Am to Cf. In the case of dedicated spent fuels or targets, the actinides to be separated also include U, Pu and Np. The techniques considered for the separation of these radionuclides belong to the fields of hydrometallurgy and pyrometallurgy, as in the previous FP5 programs named PARTNEW and PYROREP. The two main axes of research within EUROPART will be: The partitioning of MA (from Am to Cf) from high burn-up UO x fuels and multi-recycled MOx fuels; the partitioning of the whole actinide family for recycling, as an option for advanced dedicated fuel cycles (and in connection with the studies to be performed in the EUROTRANS integrated project). In hydrometallurgy, the research is organised into five Work Packages (WP). Four WP are dedicated to the study of partitioning methods mainly based on the use of solvent extraction methods, one WP is dedicated to the development of actinide co-conversion methods for fuel or target preparation. The research in pyrometallurgy is organized into four WP, listed hereafter: development of actinide partitioning methods, study of the basic chemistry of trans-curium elements in molten salts, study of the conditioning of the wastes, some system studies. Moreover, a strong management team will be concerned not only with the technical and financial issues arising from EUROPART, but also with information, communication and benefits for Europe. Training and education of young researchers will also pertain to the project. EUROPART has also established collaboration with US DOE and Japanese CRIEPI. (authors)

  9. SINGLE FIXED CRANE OPTIMISATION WITHIN A DISTRIBUTION CENTRE

    Directory of Open Access Journals (Sweden)

    J. Matthews

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: This paper considersthe optimisation of the movement of a fixed crane operating in a single aisle of a distribution centre. The crane must move pallets in inventory between docking bays, storage locations, and picking lines. Both a static and a dynamic approach to the problem are presented. The optimisation is performed by means of tabu search, ant colony metaheuristics,and hybrids of these two methods. All these solution approaches were tested on real life data obtained from an operational distribution centre. Results indicate that the hybrid methods outperform the other approaches.

    AFRIKAANSE OPSOMMING: Die optimisering van die beweging van 'n vaste hyskraan in 'n enkele gang van 'n distribusiesentrum word in hierdie artikel beskou. Die hyskraan moet pallette vervoer tussen dokhokke, stoorposisies, en opmaaklyne. Beide 'n statiese en 'n dinamiese benadering tot die probleem word aangebied. Die optimisering word gedoen met behulp van tabu-soektogte, mierkolonieoptimisering,en hibriede van hierdie twee metodes. Al die oplossingsbenaderings is getoets met werklike data wat van 'n operasionele distribusiesentrum verkry is. Die resultate toon aan dat die hibriedmetodes die beste oplossings lewer.

  10. Harvesting and transport operations to optimise biomass supply chain and industrial biorefinery processes

    Directory of Open Access Journals (Sweden)

    Robert Matindi

    2018-10-01

    Full Text Available In Australia, Bioenergy plays an important role in modern power systems, where many biomass resources provide greenhouse gas neutral and electricity at a variety of scales. By 2050, the Biomass energy is projected to have a 40-50 % share as an alternative source of energy. In addition to conversion of biomass, barriers and uncertainties in the production, supply may hinder biomass energy development. The sugarcane is an essential ingredient in the production of Bioenergy, across the whole spectrum ranging from the first generation to second generation, e.g., production of energy from the lignocellulosic component of the sugarcane initially regarded as waste (bagasse and cane residue. Sustainable recovery of the Lignocellulosic component of sugarcane from the field through a structured process is largely unknown and associated with high capital outlay that have stifled the growth of bioenergy sector. In this context, this paper develops a new scheduler to optimise the recovery of lignocellulosic component of sugarcane and cane, transport and harvest systems with reducing the associated costs and operational time. An Optimisation Algorithm called Limited Discrepancy Search has been adapted and integrated with the developed scheduling transport algorithms. The developed algorithms are formulated and coded by Optimization Programming Language (OPL to obtain the optimised cane and cane residues transport schedules. Computational experiments demonstrate that high-quality solutions are obtainable for industry-scale instances. To provide insightful decisions, sensitivity analysis is conducted in terms of different scenarios and criteria.

  11. Multi-objective evolutionary optimisation for product design and manufacturing

    CERN Document Server

    2011-01-01

    Presents state-of-the-art research in the area of multi-objective evolutionary optimisation for integrated product design and manufacturing Provides a comprehensive review of the literature Gives in-depth descriptions of recently developed innovative and novel methodologies, algorithms and systems in the area of modelling, simulation and optimisation

  12. Natural Erosion of Sandstone as Shape Optimisation.

    Science.gov (United States)

    Ostanin, Igor; Safonov, Alexander; Oseledets, Ivan

    2017-12-11

    Natural arches, pillars and other exotic sandstone formations have always been attracting attention for their unusual shapes and amazing mechanical balance that leave a strong impression of intelligent design rather than the result of a stochastic process. It has been recently demonstrated that these shapes could have been the result of the negative feedback between stress and erosion that originates in fundamental laws of friction between the rock's constituent particles. Here we present a deeper analysis of this idea and bridge it with the approaches utilized in shape and topology optimisation. It appears that the processes of natural erosion, driven by stochastic surface forces and Mohr-Coulomb law of dry friction, can be viewed within the framework of local optimisation for minimum elastic strain energy. Our hypothesis is confirmed by numerical simulations of the erosion using the topological-shape optimisation model. Our work contributes to a better understanding of stochastic erosion and feasible landscape formations that could be found on Earth and beyond.

  13. Sampling strategy for a large scale indoor radiation survey - a pilot project

    International Nuclear Information System (INIS)

    Strand, T.; Stranden, E.

    1986-01-01

    Optimisation of a stratified random sampling strategy for large scale indoor radiation surveys is discussed. It is based on the results from a small scale pilot project where variances in dose rates within different categories of houses were assessed. By selecting a predetermined precision level for the mean dose rate in a given region, the number of measurements needed can be optimised. The results of a pilot project in Norway are presented together with the development of the final sampling strategy for a planned large scale survey. (author)

  14. Optimising the remediation of sites contaminated by the Wismut uranium mining operations using performance and risk assessment

    Energy Technology Data Exchange (ETDEWEB)

    Pelz, F.; Jakubick, A.Th.; Kahnt, R. [Wismut GmbH, Chemnitz (Germany)

    2003-07-01

    The cost and risk assessment at Wismut GmbH is performed for optimising the remediation of sites contaminated by uranium mining and milling. An iterative either probabilistic or deterministic 'top-down' model of the remediation project as an integrated system is used. Initially all relevant processes are captured in a rather abstract and simplistic way. In the course of the model development those variables and processes to which results have been shown to be sensitive are described in more detail. This approach is useful for identifying any gaps in the knowledge base that have to be filled in the course of the multi-attributive decision making. The requirement for optimisation, also with respect to socio-economic impacts, is met by including other variables in addition to costs and health risks. (authors)

  15. Optimising the remediation of sites contaminated by the Wismut uranium mining operations using performance and risk assessment

    International Nuclear Information System (INIS)

    Pelz, F.; Jakubick, A.Th.; Kahnt, R.

    2003-01-01

    The cost and risk assessment at Wismut GmbH is performed for optimising the remediation of sites contaminated by uranium mining and milling. An iterative either probabilistic or deterministic 'top-down' model of the remediation project as an integrated system is used. Initially all relevant processes are captured in a rather abstract and simplistic way. In the course of the model development those variables and processes to which results have been shown to be sensitive are described in more detail. This approach is useful for identifying any gaps in the knowledge base that have to be filled in the course of the multi-attributive decision making. The requirement for optimisation, also with respect to socio-economic impacts, is met by including other variables in addition to costs and health risks. (authors)

  16. Techno-economic optimisation of energy systems; Contribution a l'optimisation technico-economique de systemes energetiques

    Energy Technology Data Exchange (ETDEWEB)

    Mansilla Pellen, Ch

    2006-07-15

    The traditional approach currently used to assess the economic interest of energy systems is based on a defined flow-sheet. Some studies have shown that the flow-sheets corresponding to the best thermodynamic efficiencies do not necessarily lead to the best production costs. A method called techno-economic optimisation was proposed. This method aims at minimising the production cost of a given energy system, including both investment and operating costs. It was implemented using genetic algorithms. This approach was compared to the heat integration method on two different examples, thus validating its interest. Techno-economic optimisation was then applied to different energy systems dealing with hydrogen as well as electricity production. (author)

  17. Application of Surpac and Whittle Software in Open Pit Optimisation ...

    African Journals Online (AJOL)

    Application of Surpac and Whittle Software in Open Pit Optimisation and Design. ... This paper studies the Surpac and Whittle software and their application in designing an optimised pit. ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  18. Topology Optimisation of Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Thike Aye Min

    2016-01-01

    Full Text Available Wireless sensor networks are widely used in a variety of fields including industrial environments. In case of a clustered network the location of cluster head affects the reliability of the network operation. Finding of the optimum location of the cluster head, therefore, is critical for the design of a network. This paper discusses the optimisation approach, based on the brute force algorithm, in the context of topology optimisation of a cluster structure centralised wireless sensor network. Two examples are given to verify the approach that demonstrate the implementation of the brute force algorithm to find an optimum location of the cluster head.

  19. Application of ant colony optimisation in distribution transformer sizing

    African Journals Online (AJOL)

    This study proposes an optimisation method for transformer sizing in power system using ant colony optimisation and a verification of the process by MATLAB software. The aim is to address the issue of transformer sizing which is a major challenge affecting its effective performance, longevity, huge capital cost and power ...

  20. Optimisation of Software-Defined Networks Performance Using a Hybrid Intelligent System

    Directory of Open Access Journals (Sweden)

    Ann Sabih

    2017-06-01

    Full Text Available This paper proposes a novel intelligent technique that has been designed to optimise the performance of Software Defined Networks (SDN. The proposed hybrid intelligent system has employed integration of intelligence-based optimisation approaches with the artificial neural network. These heuristic optimisation methods include Genetic Algorithms (GA and Particle Swarm Optimisation (PSO. These methods were utilised separately in order to select the best inputs to maximise SDN performance. In order to identify SDN behaviour, the neural network model is trained and applied. The maximal optimisation approach has been identified using an analytical approach that considered SDN performance and the computational time as objective functions. Initially, the general model of the neural network was tested with unseen data before implementing the model using GA and PSO to determine the optimal performance of SDN. The results showed that the SDN represented by Artificial Neural Network ANN, and optmised by PSO, generated a better configuration with regards to computational efficiency and performance index.

  1. DIMOND II: Measures for optimising radiological information content and dose in digital imaging

    International Nuclear Information System (INIS)

    Dowling, A.; Malone, J.; Marsh, D.

    2001-01-01

    The European Commission concerted action on 'Digital Imaging: Measures for Optimising Radiological Information Content and Dose', DIMOND II, was conducted by 12 European partners over the period January 1997 to June 1999. The objective of the concerted action was to initiate a project in the area of digital medical imaging where practice was evolving without structured research in radiation protection, optimisation or justification. The main issues addressed were patient and staff dosimetry, image quality, quality criteria and technical issues. The scope included computed radiography (CR), image intensifier radiography and fluoroscopy, cardiology and interventional procedures. The concerted action was based on the consolidation of work conducted in the partner's institutions together with elective new work. Protocols and approaches to dosimetry, radiological information content/image quality measurement and quality criteria were established and presented at an international workshop held in Dublin in June 1999. Details of the work conducted during the DIMOND II concerted action and a summary of the main findings and conclusions are presented in this contribution. (author)

  2. Critical factors for optimising skill-grade-mix based on principles of Lean Management - a qualitative substudy

    Science.gov (United States)

    Inauen, Alice; Rettke, Horst; Fridrich, Annemarie; Spirig, Rebecca; Bauer, Georg F

    2017-01-01

    Background: Due to scarce resources in health care, staff deployment has to meet the demands. To optimise skill-grade-mix, a Swiss University Hospital initiated a project based on principles of Lean Management. The project team accompanied each participating nursing department and scientifically evaluated the results of the project. Aim: The aim of this qualitative sub-study was to identify critical success factors of this project. Method: In four focus groups, participants discussed their experience of the project. Recruitment was performed from departments assessing the impact of the project retrospectively either positive or critical. In addition, the degree of direct involvement in the project served as a distinguishing criterion. Results: While the degree of direct involvement in the project was not decisive, conflicting opinions and experiences appeared in the groups with more positive or critical project evaluation. Transparency, context and attitude proved critical for the project’s success. Conclusions: Project managers should ensure transparency of the project’s progress and matching of the project structure with local conditions in order to support participants in their critical or positive attitude towards the project.

  3. Ants Colony Optimisation of a Measuring Path of Prismatic Parts on a CMM

    Directory of Open Access Journals (Sweden)

    Stojadinovic Slavenko M.

    2016-03-01

    Full Text Available This paper presents optimisation of a measuring probe path in inspecting the prismatic parts on a CMM. The optimisation model is based on: (i the mathematical model that establishes an initial collision-free path presented by a set of points, and (ii the solution of Travelling Salesman Problem (TSP obtained with Ant Colony Optimisation (ACO. In order to solve TSP, an ACO algorithm that aims to find the shortest path of ant colony movement (i.e. the optimised path is applied. Then, the optimised path is compared with the measuring path obtained with online programming on CMM ZEISS UMM500 and with the measuring path obtained in the CMM inspection module of Pro/ENGINEER® software. The results of comparing the optimised path with the other two generated paths show that the optimised path is at least 20% shorter than the path obtained by on-line programming on CMM ZEISS UMM500, and at least 10% shorter than the path obtained by using the CMM module in Pro/ENGINEER®.

  4. PHYSICAL-MATEMATICALSCIENCE MECHANICS SIMULATION CHALLENGES IN OPTIMISING THEORETICAL METAL CUTTING TASKS

    Directory of Open Access Journals (Sweden)

    Rasul V. Guseynov

    2017-01-01

    Full Text Available Abstract. Objectives In the article, problems in the optimising of machining operations, which provide end-unit production of the required quality with a minimum processing cost, are addressed. Methods Increasing the effectiveness of experimental research was achieved through the use of mathematical methods for planning experiments for optimising metal cutting tasks. The minimal processing cost model, in which the objective function is polynomial, is adopted as a criterion for the selection of optimal parameters. Results Polynomial models of the influence of angles φ, α, γ on the torque applied when cutting threads in various steels are constructed. Optimum values of the geometrical tool parameters were obtained using the criterion of minimum cutting forces during processing. The high stability of tools having optimal geometric parameters is determined. It is shown that the use of experimental planning methods allows the optimisation of cutting parameters. In optimising solutions to metal cutting problems, it is found to be expedient to use multifactor experimental planning methods and to select the cutting force as the optimisation parameter when determining tool geometry. Conclusion The joint use of geometric programming and experiment planning methods in order to optimise the parameters of cutting significantly increases the efficiency of technological metal processing approaches. 

  5. Algorithme intelligent d'optimisation d'un design structurel de grande envergure

    Science.gov (United States)

    Dominique, Stephane

    The implementation of an automated decision support system in the field of design and structural optimisation can give a significant advantage to any industry working on mechanical designs. Indeed, by providing solution ideas to a designer or by upgrading existing design solutions while the designer is not at work, the system may reduce the project cycle time, or allow more time to produce a better design. This thesis presents a new approach to automate a design process based on Case-Based Reasoning (CBR), in combination with a new genetic algorithm named Genetic Algorithm with Territorial core Evolution (GATE). This approach was developed in order to reduce the operating cost of the process. However, as the system implementation cost is quite expensive, the approach is better suited for large scale design problem, and particularly for design problems that the designer plans to solve for many different specification sets. First, the CBR process uses a databank filled with every known solution to similar design problems. Then, the closest solutions to the current problem in term of specifications are selected. After this, during the adaptation phase, an artificial neural network (ANN) interpolates amongst known solutions to produce an additional solution to the current problem using the current specifications as inputs. Each solution produced and selected by the CBR is then used to initialize the population of an island of the genetic algorithm. The algorithm will optimise the solution further during the refinement phase. Using progressive refinement, the algorithm starts using only the most important variables for the problem. Then, as the optimisation progress, the remaining variables are gradually introduced, layer by layer. The genetic algorithm that is used is a new algorithm specifically created during this thesis to solve optimisation problems from the field of mechanical device structural design. The algorithm is named GATE, and is essentially a real number

  6. Optimisation of rocker sole footwear for prevention of first plantar ulcer: comparison of group-optimised and individually-selected footwear designs.

    Science.gov (United States)

    Preece, Stephen J; Chapman, Jonathan D; Braunstein, Bjoern; Brüggemann, Gert-Peter; Nester, Christopher J

    2017-01-01

    Appropriate footwear for individuals with diabetes but no ulceration history could reduce the risk of first ulceration. However, individuals who deem themselves at low risk are unlikely to seek out bespoke footwear which is personalised. Therefore, our primary aim was to investigate whether group-optimised footwear designs, which could be prefabricated and delivered in a retail setting, could achieve appropriate pressure reduction, or whether footwear selection must be on a patient-by-patient basis. A second aim was to compare responses to footwear design between healthy participants and people with diabetes in order to understand the transferability of previous footwear research, performed in healthy populations. Plantar pressures were recorded from 102 individuals with diabetes, considered at low risk of ulceration. This cohort included 17 individuals with peripheral neuropathy. We also collected data from 66 healthy controls. Each participant walked in 8 rocker shoe designs (4 apex positions × 2 rocker angles). ANOVA analysis was then used to understand the effect of two design features and descriptive statistics used to identify the group-optimised design. Using 200 kPa as a target, this group-optimised design was then compared to the design identified as the best for each participant (using plantar pressure data). Peak plantar pressure increased significantly as apex position was moved distally and rocker angle reduced ( p  footwear which was individually selected. In terms of optimised footwear designs, healthy participants demonstrated the same response as participants with diabetes, despite having lower plantar pressures. This is the first study demonstrating that a group-optimised, generic rocker shoe might perform almost as well as footwear selected on a patient by patient basis in a low risk patient group. This work provides a starting point for clinical evaluation of generic versus personalised pressure reducing footwear.

  7. Optimisation of searches for Supersymmetry with the ATLAS detector

    Energy Technology Data Exchange (ETDEWEB)

    Zvolsky, Milan

    2012-01-15

    The ATLAS experiment is one of the four large experiments at the Large Hadron Collider which is specifically designed to search for the Higgs boson and physics beyond the Standard Model. The aim of this thesis is the optimisation of searches for Supersymmetry in decays with two leptons and missing transverse energy in the final state. Two different optimisation studies have been performed for two important analysis aspects: The final signal region selection and the choice of the trigger selection. In the first part of the analysis, a cut-based optimisation of signal regions is performed, maximising the signal for a minimal background contamination. By this, the signal yield can in parts be more than doubled. The second approach is to introduce di-lepton triggers which allow to lower the lepton transverse momentum threshold, thus enhancing the number of selected signal events significantly. The signal region optimisation was considered for the choice of the final event selection in the ATLAS di-lepton analyses. The trigger study contributed to the incorporation of di-lepton triggers to the ATLAS trigger menu. (orig.)

  8. Data for TROTS – The Radiotherapy Optimisation Test Set

    Directory of Open Access Journals (Sweden)

    Sebastiaan Breedveld

    2017-06-01

    Full Text Available The Radiotherapy Optimisation Test Set (TROTS is an extensive set of problems originating from radiotherapy (radiation therapy treatment planning. This dataset is created for 2 purposes: (1 to supply a large-scale dense dataset to measure performance and quality of mathematical solvers, and (2 to supply a dataset to investigate the multi-criteria optimisation and decision-making nature of the radiotherapy problem. The dataset contains 120 problems (patients, divided over 6 different treatment protocols/tumour types. Each problem contains numerical data, a configuration for the optimisation problem, and data required to visualise and interpret the results. The data is stored as HDF5 compatible Matlab files, and includes scripts to work with the dataset.

  9. The optimisation of wedge filters in radiotherapy of the prostate

    International Nuclear Information System (INIS)

    Oldham, Mark; Neal, Anthony J.; Webb, Steve

    1995-01-01

    A treatment plan optimisation algorithm has been applied to 12 patients with early prostate cancer in order to determine the optimum beam-weights and wedge angles for a standard conformal three-field treatment technique. The optimisation algorithm was based on fast-simulated-annealing using a cost function designed to achieve a uniform dose in the planning-target-volume (PTV) and to minimise the integral doses to the organs-at-risk. The algorithm has been applied to standard conformal three-field plans created by an experienced human planner, and run in three PLAN MODES: (1) where the wedge angles were fixed by the human planner and only the beam-weights were optimised; (2) where both the wedge angles and beam-weights were optimised; and (3) where both the wedge angles and beam-weights were optimised and a non-uniform dose was prescribed to the PTV. In the latter PLAN MODE, a uniform 100% dose was prescribed to all of the PTV except for that region that overlaps with the rectum where a lower (e.g., 90%) dose was prescribed. The resulting optimised plans have been compared with those of the human planner who found beam-weights by conventional forward planning techniques. Plans were compared on the basis of dose statistics, normal-tissue-complication-probability (NTCP) and tumour-control-probability (TCP). The results of the comparison showed that all three PLAN MODES produced plans with slightly higher TCP for the same rectal NTCP, than the human planner. The best results were observed for PLAN MODE 3, where an average increase in TCP of 0.73% (± 0.20, 95% confidence interval) was predicted by the biological models. This increase arises from a beneficial dose gradient which is produced across the tumour. Although the TCP gain is small it comes with no increase in treatment complexity, and could translate into increased cures given the large numbers of patients being referred. A study of the beam-weights and wedge angles chosen by the optimisation algorithm revealed

  10. GAOS: Spatial optimisation of crop and nature within agricultural fields

    NARCIS (Netherlands)

    Bruin, de S.; Janssen, H.; Klompe, A.; Lerink, P.; Vanmeulebrouk, B.

    2010-01-01

    This paper proposes and demonstrates a spatial optimiser that allocates areas of inefficient machine manoeuvring to field margins thus improving the use of available space and supporting map-based Controlled Traffic Farming. A prototype web service (GAOS) allows farmers to optimise tracks within

  11. Techno-economic optimisation of energy systems

    International Nuclear Information System (INIS)

    Mansilla Pellen, Ch.

    2006-07-01

    The traditional approach currently used to assess the economic interest of energy systems is based on a defined flow-sheet. Some studies have shown that the flow-sheets corresponding to the best thermodynamic efficiencies do not necessarily lead to the best production costs. A method called techno-economic optimisation was proposed. This method aims at minimising the production cost of a given energy system, including both investment and operating costs. It was implemented using genetic algorithms. This approach was compared to the heat integration method on two different examples, thus validating its interest. Techno-economic optimisation was then applied to different energy systems dealing with hydrogen as well as electricity production. (author)

  12. Robustness analysis of bogie suspension components Pareto optimised values

    Science.gov (United States)

    Mousavi Bideleh, Seyed Milad

    2017-08-01

    Bogie suspension system of high speed trains can significantly affect vehicle performance. Multiobjective optimisation problems are often formulated and solved to find the Pareto optimised values of the suspension components and improve cost efficiency in railway operations from different perspectives. Uncertainties in the design parameters of suspension system can negatively influence the dynamics behaviour of railway vehicles. In this regard, robustness analysis of a bogie dynamics response with respect to uncertainties in the suspension design parameters is considered. A one-car railway vehicle model with 50 degrees of freedom and wear/comfort Pareto optimised values of bogie suspension components is chosen for the analysis. Longitudinal and lateral primary stiffnesses, longitudinal and vertical secondary stiffnesses, as well as yaw damping are considered as five design parameters. The effects of parameter uncertainties on wear, ride comfort, track shift force, stability, and risk of derailment are studied by varying the design parameters around their respective Pareto optimised values according to a lognormal distribution with different coefficient of variations (COVs). The robustness analysis is carried out based on the maximum entropy concept. The multiplicative dimensional reduction method is utilised to simplify the calculation of fractional moments and improve the computational efficiency. The results showed that the dynamics response of the vehicle with wear/comfort Pareto optimised values of bogie suspension is robust against uncertainties in the design parameters and the probability of failure is small for parameter uncertainties with COV up to 0.1.

  13. Performance characterisation and optimisation of the HIPOS positron generator setup

    Energy Technology Data Exchange (ETDEWEB)

    Tucek, K., E-mail: kamil.tucek@ec.europa.eu [European Commission, Joint Research Centre, Institute for Energy and Transport, P.O. Box 2, NL-1755 ZG Petten (Netherlands); Zeman, A.; Daquino, G.; Debarberis, L. [European Commission, Joint Research Centre, Institute for Energy and Transport, P.O. Box 2, NL-1755 ZG Petten (Netherlands); Hogenbirk, A. [Nuclear Research and Consultancy Group (NRG), P.O. Box 25, NL-1755 ZG Petten (Netherlands)

    2012-01-01

    As part of an Exploratory Research Project at the Institute for Energy and Transport (Joint Research Centre of the European Commission), a feasibility assessment was performed for the construction and placement of a high-intensity positron facility (HIPOS) in a beam tube, HB9, at the High flux reactor (HFR) in Petten. This paper reports on the results of Monte Carlo simulations to optimise the concept of the HIPOS positron generator and to determine the performance characteristics of the chosen generator design. In the first step, a detailed model of the HFR reactor core, reflector, instrumentation and HB9 beam tube was prepared, and coupled neutron and photon transport calculations were carried out with the MCNP4C3 code to establish neutron and photon source terms on boundary surfaces of the HB9 beam tube. These sources were subsequently used with the MCNPX code to optimise the positron generator concept and geometry. The results showed that the positron beam can reach an integral intensity of 10{sup 13} e{sup +}/s before the moderation stage, easily meeting the specified target and confirming the hypothesis that very high positron yields can be obtained by using combined neutron and gamma radiation sources from a high flux reactor. Full details of the research work are reported in this study.

  14. Model-based online optimisation. Pt. 1: active learning; Modellbasierte Online-Optimierung moderner Verbrennungsmotoren. T. 1: Aktives Lernen

    Energy Technology Data Exchange (ETDEWEB)

    Poland, J.; Knoedler, K.; Zell, A. [Tuebingen Univ. (Germany). Lehrstuhl fuer Rechnerarchitektur; Fleischhauer, T.; Mitterer, A.; Ullmann, S. [BMW Group (Germany)

    2003-05-01

    This two-part article presents the model-based optimisation algorithm ''mbminimize''. It was developed in a corporate project of the University Tuebingen and the BMW Group for the purpose of optimising internal combustion engines online on the engine test bed. The first part concentrates on the basic algorithmic design, as well as on modelling, experimental design and active learning. The second part will discuss strategies for dealing with limits such as knocking. (orig.) [German] Dieser zweiteilige Beitrag stellt den modellbasierten Optimierungsalgorithmus ''mbminimize'' vor, der in Kooperation von der Universitaet Tuebingen und der BMW Group fuer die Online-Optimierung von Verbrennungsmotoren entwickelt wurde. Der vorliegende erste Teil konzentriert sich auf das grundlegende algorithmische Design, auf Modellierung, Versuchsplanung und aktives Lernen. Der zweite Teil diskutiert Strategien zur Behandlung von Limits wie Motorklopfen.

  15. Operational Radiological Protection and Aspects of Optimisation

    International Nuclear Information System (INIS)

    Lazo, E.; Lindvall, C.G.

    2005-01-01

    Since 1992, the Nuclear Energy Agency (NEA), along with the International Atomic Energy Agency (IAEA), has sponsored the Information System on Occupational Exposure (ISOE). ISOE collects and analyses occupational exposure data and experience from over 400 nuclear power plants around the world and is a forum for radiological protection experts from both nuclear power plants and regulatory authorities to share lessons learned and best practices in the management of worker radiation exposures. In connection to the ongoing work of the International Commission on Radiological Protection (ICRP) to develop new recommendations, the ISOE programme has been interested in how the new recommendations would affect operational radiological protection application at nuclear power plants. Bearing in mind that the ICRP is developing, in addition to new general recommendations, a new recommendation specifically on optimisation, the ISOE programme created a working group to study the operational aspects of optimisation, and to identify the key factors in optimisation that could usefully be reflected in ICRP recommendations. In addition, the Group identified areas where further ICRP clarification and guidance would be of assistance to practitioners, both at the plant and the regulatory authority. The specific objective of this ISOE work was to provide operational radiological protection input, based on practical experience, to the development of new ICRP recommendations, particularly in the area of optimisation. This will help assure that new recommendations will best serve the needs of those implementing radiation protection standards, for the public and for workers, at both national and international levels. (author)

  16. Optimising polarised neutron scattering measurements--XYZ and polarimetry analysis

    International Nuclear Information System (INIS)

    Cussen, L.D.; Goossens, D.J.

    2002-01-01

    The analytic optimisation of neutron scattering measurements made using XYZ polarisation analysis and neutron polarimetry techniques is discussed. Expressions for the 'quality factor' and the optimum division of counting time for the XYZ technique are presented. For neutron polarimetry the optimisation is identified as analogous to that for measuring the flipping ratio and reference is made to the results already in the literature

  17. Optimising polarised neutron scattering measurements--XYZ and polarimetry analysis

    CERN Document Server

    Cussen, L D

    2002-01-01

    The analytic optimisation of neutron scattering measurements made using XYZ polarisation analysis and neutron polarimetry techniques is discussed. Expressions for the 'quality factor' and the optimum division of counting time for the XYZ technique are presented. For neutron polarimetry the optimisation is identified as analogous to that for measuring the flipping ratio and reference is made to the results already in the literature.

  18. Design Optimisation and Conrol of a Pilot Operated Seat Valve

    DEFF Research Database (Denmark)

    Nielsen, Brian; Andersen, Torben Ole; Hansen, Michael Rygaard

    2004-01-01

    The paper gives an approach for optimisation of the bandwidth of a pilot operated seat valve for mobile applications. Physical dimensions as well as parameters of the implemented control loop are optimised simultaneously. The frequency response of the valve varies as a function of the pressure drop...

  19. Adjoint Optimisation of the Turbulent Flow in an Annular Diffuser

    DEFF Research Database (Denmark)

    Gotfredsen, Erik; Agular Knudsen, Christian; Kunoy, Jens Dahl

    2017-01-01

    In the present study, a numerical optimisation of guide vanes in an annular diffuser, is performed. The optimisation is preformed for the purpose of improving the following two parameters simultaneously; the first parameter is the uniformity perpen-dicular to the flow direction, a 1/3 diameter do...

  20. Neutronic design of the XT-ADS core

    International Nuclear Information System (INIS)

    Van den Eynde, G.

    2007-01-01

    The EUROTRANS project is an integrated project in the 6th European Framework Program in the context of Partitioning and Transmutation. The objective of this project is the step-wise approach to a European Transmutation Demonstration. This project aims to deliver an advanced design of a small-scale Accelerator Driven System (ADS), XT-ADS, as well as the conceptual design of a European Facility for Industrial Transmutation (EFIT). The partners of this project accepted to use the MYRRHA Draft-2 design file as a starting basis for the design of the short-term XT-ADS demonstration machine. Instead of starting from a blank page, this allowed optimising an existing design towards the needs of XT-ADS, and this within the accepted limits of the safety requirements. Many options have been revisited and the framework is now set up. The main two objectives of the XT-ADS machine are the following: to demonstrate the feasibility of the ADS concept and to perform as a multi-purpose irradiation facility. Special attention is paid to the possibility of testing fuel dedicated to transmutation of minor actinides and long-life fission products. During the demonstration phase, the core will be loaded with MOX fuel in a clean core configuration. Since the XT-ADS must be a representative prototype, it has to operate at a reasonable power, a minimum of 50 MWth was set in the objectives. After this phase, the core will house In-Pile-Sections of different types for irradiating material samples, new types of fuel pins. We aim to be able to provide irradiation conditions that are close to EFIT conditions so XT-ADS can be used as a test-bed for EFIT parts

  1. Optimisation of Protection as applicable to geological disposal: the ICRP view

    International Nuclear Information System (INIS)

    Weiss, W.

    2010-01-01

    Wolfgang Weiss (BfS), vice-chair of ICRP Committee 4, recalled that the role of optimisation is to select the best protection options under the prevailing circumstances based on scientific considerations, societal concerns and ethical aspects as well as considerations of transparency. An important role of the concept of optimisation of protection is to foster a 'safety culture' and thereby to engender a state of thinking in everyone responsible for control of radiation exposures, such that they are continuously asking themselves the question, 'Have I done all that I reasonably can to avoid or reduce these doses?' Clearly, the answer to this question is a matter of judgement and necessitates co-operation between all parties involved and, as a minimum, the operating management and the regulatory agencies, but the dialogue would be more complete if other stakeholders were also involved. What kinds of checks and balances or factors would be needed to be considered for an 'optimal' system? Can indicators be identified? Quantitative methods may provide input to this dialogue but they should never be the sole input. The ICRP considers that the parameters to take into account include also social considerations and values, environmental considerations, as well as technical and economic considerations. Wolfgang Weiss approached the question of the distinction to be made between system optimisation (in the sense of taking account of social and economic as well as of all types of hazards) and optimisation of radiological protection. The position of the ICRP is that the system of protection that it proposes is based on both science (quantification of the health risk) and value judgement (what is an acceptable risk?) and optimisation is the recommended process to integrate both aspects. Indeed, there has been evolution since the old system of intervention levels to the new system, whereby, even if the level of the dose or risk (which is called constraint in ICRP-81 ) is met

  2. Study on the evolutionary optimisation of the topology of network control systems

    Science.gov (United States)

    Zhou, Zude; Chen, Benyuan; Wang, Hong; Fan, Zhun

    2010-08-01

    Computer networks have been very popular in enterprise applications. However, optimisation of network designs that allows networks to be used more efficiently in industrial environment and enterprise applications remains an interesting research topic. This article mainly discusses the topology optimisation theory and methods of the network control system based on switched Ethernet in an industrial context. Factors that affect the real-time performance of the industrial control network are presented in detail, and optimisation criteria with their internal relations are analysed. After the definition of performance parameters, the normalised indices for the evaluation of the topology optimisation are proposed. The topology optimisation problem is formulated as a multi-objective optimisation problem and the evolutionary algorithm is applied to solve it. Special communication characteristics of the industrial control network are considered in the optimisation process. In respect to the evolutionary algorithm design, an improved arena algorithm is proposed for the construction of the non-dominated set of the population. In addition, for the evaluation of individuals, the integrated use of the dominative relation method and the objective function combination method, for reducing the computational cost of the algorithm, are given. Simulation tests show that the performance of the proposed algorithm is preferable and superior compared to other algorithms. The final solution greatly improves the following indices: traffic localisation, traffic balance and utilisation rate balance of switches. In addition, a new performance index with its estimation process is proposed.

  3. Optimising neutron polarizers--measuring the flipping ratio and related quantities

    CERN Document Server

    Goossens, D J

    2002-01-01

    The continuing development of gaseous spin polarized sup 3 He transmission filters for use as neutron polarizers makes the choice of optimum thickness for these filters an important consideration. The 'quality factors' derived for the optimisation of transmission filters for particular measurements are general to all neutron polarizers. In this work optimisation conditions for neutron polarizers are derived and discussed for the family of studies related to measuring the flipping ratio from samples. The application of the optimisation conditions to sup 3 He transmission filters and other types of neutron polarizers is discussed. Absolute comparisons are made between the effectiveness of different types of polarizers for this sort of work.

  4. Cultural-based particle swarm for dynamic optimisation problems

    Science.gov (United States)

    Daneshyari, Moayed; Yen, Gary G.

    2012-07-01

    Many practical optimisation problems are with the existence of uncertainties, among which a significant number belong to the dynamic optimisation problem (DOP) category in which the fitness function changes through time. In this study, we propose the cultural-based particle swarm optimisation (PSO) to solve DOP problems. A cultural framework is adopted incorporating the required information from the PSO into five sections of the belief space, namely situational, temporal, domain, normative and spatial knowledge. The stored information will be adopted to detect the changes in the environment and assists response to the change through a diversity-based repulsion among particles and migration among swarms in the population space, and also helps in selecting the leading particles in three different levels, personal, swarm and global levels. Comparison of the proposed heuristics over several difficult dynamic benchmark problems demonstrates the better or equal performance with respect to most of other selected state-of-the-art dynamic PSO heuristics.

  5. Optimisation of load control

    International Nuclear Information System (INIS)

    Koponen, P.

    1998-01-01

    Electricity cannot be stored in large quantities. That is why the electricity supply and consumption are always almost equal in large power supply systems. If this balance were disturbed beyond stability, the system or a part of it would collapse until a new stable equilibrium is reached. The balance between supply and consumption is mainly maintained by controlling the power production, but also the electricity consumption or, in other words, the load is controlled. Controlling the load of the power supply system is important, if easily controllable power production capacity is limited. Temporary shortage of capacity causes high peaks in the energy price in the electricity market. Load control either reduces the electricity consumption during peak consumption and peak price or moves electricity consumption to some other time. The project Optimisation of Load Control is a part of the EDISON research program for distribution automation. The following areas were studied: Optimization of space heating and ventilation, when electricity price is time variable, load control model in power purchase optimization, optimization of direct load control sequences, interaction between load control optimization and power purchase optimization, literature on load control, optimization methods and field tests and response models of direct load control and the effects of the electricity market deregulation on load control. An overview of the main results is given in this chapter

  6. Optimisation of load control

    Energy Technology Data Exchange (ETDEWEB)

    Koponen, P [VTT Energy, Espoo (Finland)

    1998-08-01

    Electricity cannot be stored in large quantities. That is why the electricity supply and consumption are always almost equal in large power supply systems. If this balance were disturbed beyond stability, the system or a part of it would collapse until a new stable equilibrium is reached. The balance between supply and consumption is mainly maintained by controlling the power production, but also the electricity consumption or, in other words, the load is controlled. Controlling the load of the power supply system is important, if easily controllable power production capacity is limited. Temporary shortage of capacity causes high peaks in the energy price in the electricity market. Load control either reduces the electricity consumption during peak consumption and peak price or moves electricity consumption to some other time. The project Optimisation of Load Control is a part of the EDISON research program for distribution automation. The following areas were studied: Optimization of space heating and ventilation, when electricity price is time variable, load control model in power purchase optimization, optimization of direct load control sequences, interaction between load control optimization and power purchase optimization, literature on load control, optimization methods and field tests and response models of direct load control and the effects of the electricity market deregulation on load control. An overview of the main results is given in this chapter

  7. Solving dynamic multi-objective problems with vector evaluated particle swarm optimisation

    CSIR Research Space (South Africa)

    Greeff, M

    2008-06-01

    Full Text Available Many optimisation problems are multi-objective and change dynamically. Many methods use a weighted average approach to the multiple objectives. This paper introduces the usage of the vector evaluated particle swarm optimiser (VEPSO) to solve dynamic...

  8. Exploration of automatic optimisation for CUDA programming

    KAUST Repository

    Al-Mouhamed, Mayez; Khan, Ayaz ul Hassan

    2014-01-01

    © 2014 Taylor & Francis. Writing optimised compute unified device architecture (CUDA) program for graphic processing units (GPUs) is complex even for experts. We present a design methodology for a restructuring tool that converts C-loops into optimised CUDA kernels based on a three-step algorithm which are loop tiling, coalesced memory access and resource optimisation. A method for finding possible loop tiling solutions with coalesced memory access is developed and a simplified algorithm for restructuring C-loops into an efficient CUDA kernel is presented. In the evaluation, we implement matrix multiply (MM), matrix transpose (M-transpose), matrix scaling (M-scaling) and matrix vector multiply (MV) using the proposed algorithm. We present the analysis of the execution time and GPU throughput for the above applications, which favourably compare to other proposals. Evaluation is carried out while scaling the problem size and running under a variety of kernel configurations. The obtained speedup is about 28-35% for M-transpose compared to NVIDIA Software Development Kit, 33% speedup for MV compared to general purpose computation on graphics processing unit compiler, and more than 80% speedup for MM and M-scaling compared to CUDA-lite.

  9. Exploration of automatic optimisation for CUDA programming

    KAUST Repository

    Al-Mouhamed, Mayez

    2014-09-16

    © 2014 Taylor & Francis. Writing optimised compute unified device architecture (CUDA) program for graphic processing units (GPUs) is complex even for experts. We present a design methodology for a restructuring tool that converts C-loops into optimised CUDA kernels based on a three-step algorithm which are loop tiling, coalesced memory access and resource optimisation. A method for finding possible loop tiling solutions with coalesced memory access is developed and a simplified algorithm for restructuring C-loops into an efficient CUDA kernel is presented. In the evaluation, we implement matrix multiply (MM), matrix transpose (M-transpose), matrix scaling (M-scaling) and matrix vector multiply (MV) using the proposed algorithm. We present the analysis of the execution time and GPU throughput for the above applications, which favourably compare to other proposals. Evaluation is carried out while scaling the problem size and running under a variety of kernel configurations. The obtained speedup is about 28-35% for M-transpose compared to NVIDIA Software Development Kit, 33% speedup for MV compared to general purpose computation on graphics processing unit compiler, and more than 80% speedup for MM and M-scaling compared to CUDA-lite.

  10. Optimisation of BPMN Business Models via Model Checking

    DEFF Research Database (Denmark)

    Herbert, Luke Thomas; Sharp, Robin

    2013-01-01

    We present a framework for the optimisation of business processes modelled in the business process modelling language BPMN, which builds upon earlier work, where we developed a model checking based method for the analysis of BPMN models. We define a structure for expressing optimisation goals...... for synthesized BPMN components, based on probabilistic computation tree logic and real-valued reward structures of the BPMN model, allowing for the specification of complex quantitative goals. We here present a simple algorithm, inspired by concepts from evolutionary algorithms, which iteratively generates...

  11. Intelligent Support for a Computer Aided Design Optimisation Cycle

    OpenAIRE

    B. Dolšak; M. Novak; J. Kaljun

    2006-01-01

    It is becoming more and more evident that  adding intelligence  to existing computer aids, such as computer aided design systems, can lead to significant improvements in the effective and reliable performance of various engineering tasks, including design optimisation. This paper presents three different intelligent modules to be applied within a computer aided design optimisation cycle to enable more intelligent and less experience-dependent design performance. 

  12. The principle of optimisation: reasons for success and legal criticism

    International Nuclear Information System (INIS)

    Fernandez Regalado, Luis

    2008-01-01

    The International Commission on Radiological Protection (ICRP) has adopted new recommendations in 2007. In broad outlines they fundamentally continue the recommendations already approved in 1990 and later on. The principle of optimisation of protection, together with the principles of justification and dose limits, remains playing a key role of the ICRP recommendations, and it has so been for the last few years. This principle, somehow reinforced in the 2007 ICRP recommendations, has been incorporated into norms and legislation which have peacefully been in force in many countries all over the world. There are three main reasons to explain the success in the application of the principle of optimisation in radiological protection: First, the subjectivity of the sentence that embraces the principle of optimisation, 'As low as reasonably achievable' (ALARA), that allows different valid interpretations under different circumstances. Second, the pragmatism and adaptability of ALARA to all exposure situations. And third, the scientific humbleness which is behind the principle of optimisation, which makes a clear contrast with the old fashioned scientific positivism that enshrined scientist opinions. Nevertheless, from a legal point of view, there is some criticism cast over the principle of optimisation in radiological protection, where it has been transformed in compulsory norm. This criticism is based on two arguments: The lack of democratic participation in the process of elaboration of the norm, and the legal uncertainty associated to its application. Both arguments are somehow known by the ICRP which, on the one hand, has broadened the participation of experts, associations and the professional radiological protection community, increasing the transparency on how decisions on recommendations have been taken, and on the other hand, the ICRP has warned about the need for authorities to specify general criteria to develop the principle of optimisation in national

  13. Simulation and optimisation modelling approach for operation of the Hoa Binh Reservoir, Vietnam

    DEFF Research Database (Denmark)

    Ngo, Long le; Madsen, Henrik; Rosbjerg, Dan

    2007-01-01

    Hoa Binh, the largest reservoir in Vietnam, plays an important role in flood control for the Red River delta and hydropower generation. Due to its multi-purpose character, conflicts and disputes in operating the reservoir have been ongoing since its construction, particularly in the flood season....... This paper proposes to optimise the control strategies for the Hoa Binh reservoir operation by applying a combination of simulation and optimisation models. The control strategies are set up in the MIKE 11 simulation model to guide the releases of the reservoir system according to the current storage level......, the hydro-meteorological conditions, and the time of the year. A heuristic global optimisation tool, the shuffled complex evolution (SCE) algorithm, is adopted for optimising the reservoir operation. The optimisation puts focus on the trade-off between flood control and hydropower generation for the Hoa...

  14. Risk-informed optimisation of railway tracks inspection and maintenance procedures

    International Nuclear Information System (INIS)

    Podofillini, Luca; Zio, Enrico; Vatn, Jorn

    2006-01-01

    Nowadays, efforts are being made by the railway industry for the application of reliability-based and risk-informed approaches to maintenance optimisation of railway infrastructures, with the aim of reducing the operation and maintenance expenditures while still assuring high safety standards. In particular, in this paper, we address the use of ultrasonic inspection cars and develop a methodology for the determination of an optimal strategy for their use. A model is developed to calculate the risks and costs associated with an inspection strategy, giving credit to the realistic issues of the rail failure process and including the actual inspection and maintenance procedures followed by the railway company. A multi-objective optimisation viewpoint is adopted in an effort to optimise inspection and maintenance procedures with respect to both economical and safety-related aspects. More precisely, the objective functions here considered are such to drive the search towards solutions characterized by low expenditures and low derailment probability. The optimisation is performed by means of a genetic algorithm. The work has been carried out within a study of the Norwegian National Rail Administration (Jernbaneverket)

  15. MIMO-Radar Waveform Design for Beampattern Using Particle-Swarm-Optimisation

    KAUST Repository

    Ahmed, Sajid

    2012-07-31

    Multiple input multiple output (MIMO) radars have many advantages over their phased-array counterparts: improved spatial resolution; better parametric identifiably and greater flexibility to acheive the desired transmit beampattern. The desired transmit beampatterns using MIMO-radar requires the waveforms to have arbitrary auto- and cross-correlations. To design such waveforms, generally a waveform covariance matrix, R, is synthesised first then the actual waveforms are designed. Synthesis of the covariance matrix, R, is a constrained optimisation problem, which requires R to be positive semidefinite and all of its diagonal elements to be equal. To simplify the first constraint the covariance matrix is synthesised indirectly from its square-root matrix U, while for the second constraint the elements of the m-th column of U are parameterised using the coordinates of the m-hypersphere. This implicitly fulfils both of the constraints and enables us to write the cost-function in closed form. Then the cost-function is optimised using a simple particle-swarm-optimisation (PSO) technique, which requires only the cost-function and can optimise any choice of norm cost-function. © 2012 IEEE.

  16. Design of optimised backstepping controller for the synchronisation of chaotic Colpitts oscillator using shark smell algorithm

    Science.gov (United States)

    Fouladi, Ehsan; Mojallali, Hamed

    2018-01-01

    In this paper, an adaptive backstepping controller has been tuned to synchronise two chaotic Colpitts oscillators in a master-slave configuration. The parameters of the controller are determined using shark smell optimisation (SSO) algorithm. Numerical results are presented and compared with those of particle swarm optimisation (PSO) algorithm. Simulation results show better performance in terms of accuracy and convergence for the proposed optimised method compared to PSO optimised controller or any non-optimised backstepping controller.

  17. Separative power of an optimised concurrent gas centrifuge

    Energy Technology Data Exchange (ETDEWEB)

    Bogovalov, Sergey; Boman, Vladimir [National Research Nuclear University (MEPHI), Moscow (Russian Federation)

    2016-06-15

    The problem of separation of isotopes in a concurrent gas centrifuge is solved analytically for an arbitrary binary mixture of isotopes. The separative power of the optimised concurrent gas centrifuges for the uranium isotopes equals to δU = 12.7 (V/700 m/s)2(300 K/T)(L/1 m) kg·SWU/yr, where L and V are the length and linear velocity of the rotor of the gas centrifuge and T is the temperature. This equation agrees well with the empirically determined separative power of optimised counter-current gas centrifuges.

  18. Auto-optimisation for three-dimensional conformal radiotherapy of nasopharyngeal carcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Wu, V.W.C. E-mail: orvinwu@polyu.edu.hk; Kwong, D.W.L.; Sham, J.S.T.; Mui, A.W.L

    2003-08-01

    Purpose: The purpose of this study was to evaluate the application of auto-optimisation in the treatment planning of three-dimensional conformal radiotherapy (3DCRT) of nasopharyngeal carcinoma (NPC). Methods: Twenty-nine NPC patients were planned by both forward planning and auto-optimisation methods. The forward plans, which consisted of three coplanar facial fields, were produced according to the routine planning criteria. The auto-optimised plans, which consisted of 5-15 (median 9) fields, were generated by the planning system after prescribing the dose requirements and the importance weightings of the planning target volume and organs at risk. Plans produced by the two planning methods were compared by the dose volume histogram, tumour control probability (TCP), conformity index and normal tissue complication probability (NTCP). Results: The auto-optimised plans reduced the average planner's time by over 35 min. It demonstrated better TCP and conformity index than the forward plans (P=0.03 and 0.04, respectively). Besides, the parotid gland and temporo-mandibular (TM) joint were better spared with the mean dose reduction of 31.8 and 17.7%, respectively. The slight trade off was the mild dose increase in spinal cord and brain stem with their maximum doses remaining within the tolerance limits. Conclusions: The findings demonstrated the potentials of auto-optimisation for improving target dose and parotid sparing in the 3DCRT of NPC with saving of the planner's time.

  19. Auto-optimisation for three-dimensional conformal radiotherapy of nasopharyngeal carcinoma

    International Nuclear Information System (INIS)

    Wu, V.W.C.; Kwong, D.W.L.; Sham, J.S.T.; Mui, A.W.L.

    2003-01-01

    Purpose: The purpose of this study was to evaluate the application of auto-optimisation in the treatment planning of three-dimensional conformal radiotherapy (3DCRT) of nasopharyngeal carcinoma (NPC). Methods: Twenty-nine NPC patients were planned by both forward planning and auto-optimisation methods. The forward plans, which consisted of three coplanar facial fields, were produced according to the routine planning criteria. The auto-optimised plans, which consisted of 5-15 (median 9) fields, were generated by the planning system after prescribing the dose requirements and the importance weightings of the planning target volume and organs at risk. Plans produced by the two planning methods were compared by the dose volume histogram, tumour control probability (TCP), conformity index and normal tissue complication probability (NTCP). Results: The auto-optimised plans reduced the average planner's time by over 35 min. It demonstrated better TCP and conformity index than the forward plans (P=0.03 and 0.04, respectively). Besides, the parotid gland and temporo-mandibular (TM) joint were better spared with the mean dose reduction of 31.8 and 17.7%, respectively. The slight trade off was the mild dose increase in spinal cord and brain stem with their maximum doses remaining within the tolerance limits. Conclusions: The findings demonstrated the potentials of auto-optimisation for improving target dose and parotid sparing in the 3DCRT of NPC with saving of the planner's time

  20. Production optimisation in the petrochemical industry by hierarchical multivariate modelling

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Magnus; Furusjoe, Erik; Jansson, Aasa

    2004-06-01

    This project demonstrates the advantages of applying hierarchical multivariate modelling in the petrochemical industry in order to increase knowledge of the total process. The models indicate possible ways to optimise the process regarding the use of energy and raw material, which is directly linked to the environmental impact of the process. The refinery of Nynaes Refining AB (Goeteborg, Sweden) has acted as a demonstration site in this project. The models developed for the demonstration site resulted in: Detection of an unknown process disturbance and suggestions of possible causes; Indications on how to increase the yield in combination with energy savings; The possibility to predict product quality from on-line process measurements, making the results available at a higher frequency than customary laboratory analysis; Quantification of the gradually lowered efficiency of heat transfer in the furnace and increased fuel consumption as an effect of soot build-up on the furnace coils; Increased knowledge of the relation between production rate and the efficiency of the heat exchangers. This report is one of two reports from the project. It contains a technical discussion of the result with some degree of detail. A shorter and more easily accessible report is also available, see IVL report B1586-A.

  1. Application of Three Existing Stope Boundary Optimisation Methods in an Operating Underground Mine

    Science.gov (United States)

    Erdogan, Gamze; Yavuz, Mahmut

    2017-12-01

    The underground mine planning and design optimisation process have received little attention because of complexity and variability of problems in underground mines. Although a number of optimisation studies and software tools are available and some of them, in special, have been implemented effectively to determine the ultimate-pit limits in an open pit mine, there is still a lack of studies for optimisation of ultimate stope boundaries in underground mines. The proposed approaches for this purpose aim at maximizing the economic profit by selecting the best possible layout under operational, technical and physical constraints. In this paper, the existing three heuristic techniques including Floating Stope Algorithm, Maximum Value Algorithm and Mineable Shape Optimiser (MSO) are examined for optimisation of stope layout in a case study. Each technique is assessed in terms of applicability, algorithm capabilities and limitations considering the underground mine planning challenges. Finally, the results are evaluated and compared.

  2. Benchmarks for dynamic multi-objective optimisation

    CSIR Research Space (South Africa)

    Helbig, M

    2013-06-01

    Full Text Available When algorithms solve dynamic multi-objective optimisation problems (DMOOPs), benchmark functions should be used to determine whether the algorithm can overcome specific difficulties that can occur in real-world problems. However, for dynamic multi...

  3. Visual grading characteristics and ordinal regression analysis during optimisation of CT head examinations.

    Science.gov (United States)

    Zarb, Francis; McEntee, Mark F; Rainford, Louise

    2015-06-01

    To evaluate visual grading characteristics (VGC) and ordinal regression analysis during head CT optimisation as a potential alternative to visual grading assessment (VGA), traditionally employed to score anatomical visualisation. Patient images (n = 66) were obtained using current and optimised imaging protocols from two CT suites: a 16-slice scanner at the national Maltese centre for trauma and a 64-slice scanner in a private centre. Local resident radiologists (n = 6) performed VGA followed by VGC and ordinal regression analysis. VGC alone indicated that optimised protocols had similar image quality as current protocols. Ordinal logistic regression analysis provided an in-depth evaluation, criterion by criterion allowing the selective implementation of the protocols. The local radiology review panel supported the implementation of optimised protocols for brain CT examinations (including trauma) in one centre, achieving radiation dose reductions ranging from 24 % to 36 %. In the second centre a 29 % reduction in radiation dose was achieved for follow-up cases. The combined use of VGC and ordinal logistic regression analysis led to clinical decisions being taken on the implementation of the optimised protocols. This improved method of image quality analysis provided the evidence to support imaging protocol optimisation, resulting in significant radiation dose savings. • There is need for scientifically based image quality evaluation during CT optimisation. • VGC and ordinal regression analysis in combination led to better informed clinical decisions. • VGC and ordinal regression analysis led to dose reductions without compromising diagnostic efficacy.

  4. Optimisation and symmetry in experimental radiation physics

    International Nuclear Information System (INIS)

    Ghose, A.

    1988-01-01

    The present monograph is concerned with the optimisation of geometric factors in radiation physics experiments. The discussions are essentially confined to those systems in which optimisation is equivalent to symmetrical configurations of the measurement systems. They include, measurements of interaction cross section of diverse types, determination of polarisations, development of detectors with almost ideal characteristics, production of radiations with continuously variable energies and development of high efficiency spectrometers etc. The monograph is intended for use by experimental physicists investigating primary interactions of radiations with matter and associated technologies. We have illustrated the various optimisation procedures by considering the cases of the so-called ''14 MeV'' on d-t neutrons and gamma rays with energies less than 3 MeV. Developments in fusion technology are critically dependent on the availability accurate cross sections of nuclei for fast neutrons of energies at least as high as d-t neutrons. In this monograph we have discussed various techniques which can be used to improve the accuracy of such measurements and have also presented a method for generating almost monoenergetic neutrons in the 8 MeV to 13 MeV energy range which can be used to measure cross sections in this sparingly investigated region

  5. Credit price optimisation within retail banking

    African Journals Online (AJOL)

    2014-02-14

    Feb 14, 2014 ... cost based pricing, where the price of a product or service is based on the .... function obtained from fitting a logistic regression model .... Note that the proposed optimisation approach below will allow us to also incorporate.

  6. From analysis to optimisation of the entire DSK logistics chain; Von der Analyse zur Optimierung der gesamten Logistikkette DSK

    Energy Technology Data Exchange (ETDEWEB)

    Wilkin, H.J.; Dressler, H. [Deutsche Steinkohle AG (DSK), Herne (Germany); Schmidt, A. [Fraunhofer-Inst. fuer Materialfluss und Logistik (IML), Dortmund (Germany)

    2005-12-15

    Supply of materials to meet requirements and on time to open-cast and deep mines is essential to observe the defined production aims for the individual mines. The board of DSK commissioned the project ''Analysis of the entire DSK logistic chain'' with the aim of investigating all processes in material management logistics. In the follow-up project ''Optimisation of the entire DSK logistics chain'' restructuring measures will be worked out and their organisational integration in the entire company described. Starting with the present contribution first the results of the analysis project and subsequently the improvement measures along the DSK logistics chain are described. (orig.)

  7. Optimisation of Oil Production in Two – Phase Flow Reservoir Using Simultaneous Method and Interior Point Optimiser

    DEFF Research Database (Denmark)

    Lerch, Dariusz Michal; Völcker, Carsten; Capolei, Andrea

    2012-01-01

    in the reservoir. A promising decrease of these remained resources can be provided by smart wells applying water injections to sustain satisfactory pressure level in the reservoir throughout the whole process of oil production. Basically to enhance secondary recovery of the remaining oil after drilling, water...... is injected at the injection wells of the down-hole pipes. This sustains the pressure in the reservoir and drives oil towards production wells. There are however, many factors contributing to the poor conventional secondary recovery methods e.g. strong surface tension, heterogeneity of the porous rock...... fields, or closed loop optimisation, can be used for optimising the reservoir performance in terms of net present value of oil recovery or another economic objective. In order to solve an optimal control problem we use a direct collocation method where we translate a continuous problem into a discrete...

  8. Optimising agile development practices for the maintenance operation: nine heuristics

    DEFF Research Database (Denmark)

    Heeager, Lise Tordrup; Rose, Jeremy

    2014-01-01

    Agile methods are widely used and successful in many development situations and beginning to attract attention amongst the software maintenance community – both researchers and practitioners. However, it should not be assumed that implementing a well-known agile method for a maintenance department...... is therefore a trivial endeavour - the maintenance operation differs in some important respects from development work. Classical accounts of software maintenance emphasise more traditional software engineering processes, whereas recent research accounts of agile maintenance efforts uncritically focus...... on benefits. In an action research project at Aveva in Denmark we assisted with the optimisation of SCRUM, tailoring the standard process to the immediate needs of the developers. We draw on both theoretical and empirical learning to formulate nine heuristics for maintenance practitioners wishing to go agile....

  9. Alternatives for optimisation of rumen fermentation in ruminants

    Directory of Open Access Journals (Sweden)

    T. Slavov

    2017-06-01

    Full Text Available Abstract. The proper knowledge on the variety of events occurring in the rumen makes possible their optimisation with respect to the complete feed conversion and increasing the productive performance of ruminants. The inclusion of various dietary additives (supplements, biologically active substances, nutritional antibiotics, probiotics, enzymatic preparations, plant extracts etc. has an effect on the intensity and specific pathway of fermentation, and thus, on the general digestion and systemic metabolism. The optimisation of rumen digestion is a method with substantial potential for improving the efficiency of ruminant husbandry, increasing of quality of their produce and health maintenance.

  10. Optimising a shaft's geometry by applying genetic algorithms

    Directory of Open Access Journals (Sweden)

    María Alejandra Guzmán

    2005-05-01

    Full Text Available Many engnieering design tasks involve optimising several conflicting goals; these types of problem are known as Multiobjective Optimisation Problems (MOPs. Evolutionary techniques have proved to be an effective tool for finding solutions to these MOPs during the last decade, Variations on the basic generic algorithm have been particulary proposed by different researchers for finding rapid optimal solutions to MOPs. The NSGA (Non-dominated Sorting Generic Algorithm has been implemented in this paper for finding an optimal design for a shaft subjected to cyclic loads, the conflycting goals being minimum weight and minimum lateral deflection.

  11. Coil optimisation for transcranial magnetic stimulation in realistic head geometry.

    Science.gov (United States)

    Koponen, Lari M; Nieminen, Jaakko O; Mutanen, Tuomas P; Stenroos, Matti; Ilmoniemi, Risto J

    Transcranial magnetic stimulation (TMS) allows focal, non-invasive stimulation of the cortex. A TMS pulse is inherently weakly coupled to the cortex; thus, magnetic stimulation requires both high current and high voltage to reach sufficient intensity. These requirements limit, for example, the maximum repetition rate and the maximum number of consecutive pulses with the same coil due to the rise of its temperature. To develop methods to optimise, design, and manufacture energy-efficient TMS coils in realistic head geometry with an arbitrary overall coil shape. We derive a semi-analytical integration scheme for computing the magnetic field energy of an arbitrary surface current distribution, compute the electric field induced by this distribution with a boundary element method, and optimise a TMS coil for focal stimulation. Additionally, we introduce a method for manufacturing such a coil by using Litz wire and a coil former machined from polyvinyl chloride. We designed, manufactured, and validated an optimised TMS coil and applied it to brain stimulation. Our simulations indicate that this coil requires less than half the power of a commercial figure-of-eight coil, with a 41% reduction due to the optimised winding geometry and a partial contribution due to our thinner coil former and reduced conductor height. With the optimised coil, the resting motor threshold of abductor pollicis brevis was reached with the capacitor voltage below 600 V and peak current below 3000 A. The described method allows designing practical TMS coils that have considerably higher efficiency than conventional figure-of-eight coils. Copyright © 2017 Elsevier Inc. All rights reserved.

  12. Reduction environmental effects of civil aircraft through multi-objective flight plan optimisation

    International Nuclear Information System (INIS)

    Lee, D S; Gonzalez, L F; Walker, R; Periaux, J; Onate, E

    2010-01-01

    With rising environmental alarm, the reduction of critical aircraft emissions including carbon dioxides (CO 2 ) and nitrogen oxides (NO x ) is one of most important aeronautical problems. There can be many possible attempts to solve such problem by designing new wing/aircraft shape, new efficient engine, etc. The paper rather provides a set of acceptable flight plans as a first step besides replacing current aircrafts. The paper investigates a green aircraft design optimisation in terms of aircraft range, mission fuel weight (CO 2 ) and NO x using advanced Evolutionary Algorithms coupled to flight optimisation system software. Two multi-objective design optimisations are conducted to find the best set of flight plans for current aircrafts considering discretised altitude and Mach numbers without designing aircraft shape and engine types. The objectives of first optimisation are to maximise range of aircraft while minimising NO x with constant mission fuel weight. The second optimisation considers minimisation of mission fuel weight and NO x with fixed aircraft range. Numerical results show that the method is able to capture a set of useful trade-offs that reduce NO x and CO 2 (minimum mission fuel weight).

  13. Topology optimisation of passive coolers for light-emitting diode lamps

    DEFF Research Database (Denmark)

    Alexandersen, Joe

    2015-01-01

    This work applies topology optimisation to the design of passive coolers for light-emitting diode (LED) lamps. The heat sinks are cooled by the natural convection currents arising from the temperature difference between the LED lamp and the surrounding air. A large scale parallel computational....... The optimisation results show interesting features that are currently being incorporated into industrial designs for enhanced passive cooling abilities....

  14. Optimising parallel R correlation matrix calculations on gene expression data using MapReduce.

    Science.gov (United States)

    Wang, Shicai; Pandis, Ioannis; Johnson, David; Emam, Ibrahim; Guitton, Florian; Oehmichen, Axel; Guo, Yike

    2014-11-05

    High-throughput molecular profiling data has been used to improve clinical decision making by stratifying subjects based on their molecular profiles. Unsupervised clustering algorithms can be used for stratification purposes. However, the current speed of the clustering algorithms cannot meet the requirement of large-scale molecular data due to poor performance of the correlation matrix calculation. With high-throughput sequencing technologies promising to produce even larger datasets per subject, we expect the performance of the state-of-the-art statistical algorithms to be further impacted unless efforts towards optimisation are carried out. MapReduce is a widely used high performance parallel framework that can solve the problem. In this paper, we evaluate the current parallel modes for correlation calculation methods and introduce an efficient data distribution and parallel calculation algorithm based on MapReduce to optimise the correlation calculation. We studied the performance of our algorithm using two gene expression benchmarks. In the micro-benchmark, our implementation using MapReduce, based on the R package RHIPE, demonstrates a 3.26-5.83 fold increase compared to the default Snowfall and 1.56-1.64 fold increase compared to the basic RHIPE in the Euclidean, Pearson and Spearman correlations. Though vanilla R and the optimised Snowfall outperforms our optimised RHIPE in the micro-benchmark, they do not scale well with the macro-benchmark. In the macro-benchmark the optimised RHIPE performs 2.03-16.56 times faster than vanilla R. Benefiting from the 3.30-5.13 times faster data preparation, the optimised RHIPE performs 1.22-1.71 times faster than the optimised Snowfall. Both the optimised RHIPE and the optimised Snowfall successfully performs the Kendall correlation with TCGA dataset within 7 hours. Both of them conduct more than 30 times faster than the estimated vanilla R. The performance evaluation found that the new MapReduce algorithm and its

  15. Crystal structure optimisation using an auxiliary equation of state

    Science.gov (United States)

    Jackson, Adam J.; Skelton, Jonathan M.; Hendon, Christopher H.; Butler, Keith T.; Walsh, Aron

    2015-11-01

    Standard procedures for local crystal-structure optimisation involve numerous energy and force calculations. It is common to calculate an energy-volume curve, fitting an equation of state around the equilibrium cell volume. This is a computationally intensive process, in particular, for low-symmetry crystal structures where each isochoric optimisation involves energy minimisation over many degrees of freedom. Such procedures can be prohibitive for non-local exchange-correlation functionals or other "beyond" density functional theory electronic structure techniques, particularly where analytical gradients are not available. We present a simple approach for efficient optimisation of crystal structures based on a known equation of state. The equilibrium volume can be predicted from one single-point calculation and refined with successive calculations if required. The approach is validated for PbS, PbTe, ZnS, and ZnTe using nine density functionals and applied to the quaternary semiconductor Cu2ZnSnS4 and the magnetic metal-organic framework HKUST-1.

  16. Crystal structure optimisation using an auxiliary equation of state

    International Nuclear Information System (INIS)

    Jackson, Adam J.; Skelton, Jonathan M.; Hendon, Christopher H.; Butler, Keith T.; 3 Institute and Department of Materials Science and Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of))" data-affiliation=" (Centre for Sustainable Chemical Technologies and Department of Chemistry, University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom); Global E3 Institute and Department of Materials Science and Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of))" >Walsh, Aron

    2015-01-01

    Standard procedures for local crystal-structure optimisation involve numerous energy and force calculations. It is common to calculate an energy–volume curve, fitting an equation of state around the equilibrium cell volume. This is a computationally intensive process, in particular, for low-symmetry crystal structures where each isochoric optimisation involves energy minimisation over many degrees of freedom. Such procedures can be prohibitive for non-local exchange-correlation functionals or other “beyond” density functional theory electronic structure techniques, particularly where analytical gradients are not available. We present a simple approach for efficient optimisation of crystal structures based on a known equation of state. The equilibrium volume can be predicted from one single-point calculation and refined with successive calculations if required. The approach is validated for PbS, PbTe, ZnS, and ZnTe using nine density functionals and applied to the quaternary semiconductor Cu 2 ZnSnS 4 and the magnetic metal-organic framework HKUST-1

  17. Crystal structure optimisation using an auxiliary equation of state

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, Adam J.; Skelton, Jonathan M.; Hendon, Christopher H.; Butler, Keith T. [Centre for Sustainable Chemical Technologies and Department of Chemistry, University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom); Walsh, Aron, E-mail: a.walsh@bath.ac.uk [Centre for Sustainable Chemical Technologies and Department of Chemistry, University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom); Global E" 3 Institute and Department of Materials Science and Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of)

    2015-11-14

    Standard procedures for local crystal-structure optimisation involve numerous energy and force calculations. It is common to calculate an energy–volume curve, fitting an equation of state around the equilibrium cell volume. This is a computationally intensive process, in particular, for low-symmetry crystal structures where each isochoric optimisation involves energy minimisation over many degrees of freedom. Such procedures can be prohibitive for non-local exchange-correlation functionals or other “beyond” density functional theory electronic structure techniques, particularly where analytical gradients are not available. We present a simple approach for efficient optimisation of crystal structures based on a known equation of state. The equilibrium volume can be predicted from one single-point calculation and refined with successive calculations if required. The approach is validated for PbS, PbTe, ZnS, and ZnTe using nine density functionals and applied to the quaternary semiconductor Cu{sub 2}ZnSnS{sub 4} and the magnetic metal-organic framework HKUST-1.

  18. Cogeneration technologies, optimisation and implementation

    CERN Document Server

    Frangopoulos, Christos A

    2017-01-01

    Cogeneration refers to the use of a power station to deliver two or more useful forms of energy, for example, to generate electricity and heat at the same time. This book provides an integrated treatment of cogeneration, including a tour of the available technologies and their features, and how these systems can be analysed and optimised.

  19. Validation methodology focussing on fuel efficiency as applied in the eCoMove project

    NARCIS (Netherlands)

    Themann, P.; Iasi, L.; Larburu, M.; Trommer, S.

    2012-01-01

    This paper discusses the validation approach applied in the eCoMove project (a large scale EU 7th Framework Programme project). In this project, applications are developed that on the one hand optimise network-wide traffic management and control, and on the other hand advise drivers on the most

  20. Modelling, simulation, and optimisation of a downflow entrained flow reactor for black liquor gasification

    Energy Technology Data Exchange (ETDEWEB)

    Marklund, Magnus [ETC Energitekniskt Centrum, Piteaa (Sweden)

    2003-12-01

    Black liquor, a by-product of the chemical pulping process, is an important liquid fuel in the pulp and paper industry. A potential technology for improving the recovery cycle of energy and chemicals contained in the liquid fuel is pressurised gasification of black liquor (PGLG). However, uncertainties about the reliability and robustness of the technology are preventing a large-scale market introduction. One important step towards a greater trust in the process reliability is the development of simulation tools that can provide a better understanding of the process and improve performance through optimisation. In the beginning of 2001 a project was initiated in order to develop a simulation tool for an entrained-flow gasifier in PBLG based on CFD (Computational Fluid Dynamics). The aim has been to provide an advanced tool for a better understanding of process performance, to help with trouble shooting in the development plant, and for use in optimisation of a full-scale commercial gasifier. Furthermore, the project will also provide quantitative information on burner functionality through advanced laser-optical measurements by use of a Phase Doppler Anemometer (PDA). To this point in current project, three different concept models have been developed. The work has been comprised in a thesis 'Modelling and Simulation of Pressurised Black Liquor Gasification at High Temperature' and presented at Luleaa Univ. of Technology in Oct 2003. The construction of an atmospheric burner test rig has also been initiated. The main objective with the rig will be to quantify the atomisation performance of suitable burner nozzles for a PBLG gasifier that can be used as input for the CFD model. The main conclusions from the modelling work done this far can be condensed to the following points: From the first modelling results it was concluded that a wide spray pattern is preferable with respect to demand for long residence times for black liquor droplets and a low amount

  1. Energy thermal management in commercial bread-baking using a multi-objective optimisation framework

    International Nuclear Information System (INIS)

    Khatir, Zinedine; Taherkhani, A.R.; Paton, Joe; Thompson, Harvey; Kapur, Nik; Toropov, Vassili

    2015-01-01

    In response to increasing energy costs and legislative requirements energy efficient high-speed air impingement jet baking systems are now being developed. In this paper, a multi-objective optimisation framework for oven designs is presented which uses experimentally verified heat transfer correlations and high fidelity Computational Fluid Dynamics (CFD) analyses to identify optimal combinations of design features which maximise desirable characteristics such as temperature uniformity in the oven and overall energy efficiency of baking. A surrogate-assisted multi-objective optimisation framework is proposed and used to explore a range of practical oven designs, providing information on overall temperature uniformity within the oven together with ensuing energy usage and potential savings. - Highlights: • A multi-objective optimisation framework to design commercial ovens is presented. • High fidelity CFD embeds experimentally calibrated heat transfer inputs. • The optimum oven design minimises specific energy and bake time. • The Pareto front outlining the surrogate-assisted optimisation framework is built. • Optimisation of industrial bread-baking ovens reveals an energy saving of 637.6 GWh

  2. Décomposition-coordination en optimisation déterministe et stochastique

    CERN Document Server

    Carpentier, Pierre

    2017-01-01

    Ce livre considère le traitement de problèmes d'optimisation de grande taille. L'idée est d'éclater le problème d'optimisation global en sous-problèmes plus petits, donc plus faciles à résoudre, chacun impliquant l'un des sous-systèmes (décomposition), mais sans renoncer à obtenir l'optimum global, ce qui nécessite d'utiliser une procédure itérative (coordination). Ce sujet a fait l'objet de plusieurs livres publiés dans les années 70 dans le contexte de l'optimisation déterministe. Nous présentans ici les principes essentiels et méthodes de décomposition-coordination au travers de situations typiques, puis nous proposons un cadre général qui permet de construire des algorithmes corrects et d'étudier leur convergence. Cette théorie est présentée aussi bien dans le contexte de l'optimisation déterministe que stochastique. Ce matériel a été enseigné par les auteurs dans divers cours de 3ème cycle et également mis en œuvre dans de nombreuses applications industrielles. Des exerc...

  3. Multi-objective optimisation in carbon monoxide gas management at TRONOX KXN Sands

    Directory of Open Access Journals (Sweden)

    Stadler, Johan

    2014-08-01

    Full Text Available Carbon monoxide (CO is a by-product of the ilmenite smelting process from which titania slag and pig iron are produced. Prior to this project, the CO at Tronox KZN Sands in South Africa was burnt to get rid of it, producing carbon dioxide (CO2. At this plant, unprocessed materials are pre-heated using methane gas from an external supplier. The price of methane gas has increased significantly; and so this research considers the possibility of recycling CO gas and using it as an energy source to reduce methane gas demand. It is not possible to eliminate the methane gas consumption completely due to the energy demand fluctuation, and sub-plants have been assigned either CO gas or methane gas over time. Switching the gas supply between CO and methane gas involves production downtime to purge supply lines. Minimising the loss of production time while maximising the use of CO arose as a multi-objective optimisation problem (MOP with seven decision variables, and computer simulation was used to evaluate scenarios. We applied computer simulation and the multi-objective optimisation cross-entropy method (MOO CEM to find good solutions while evaluating the minimum number of scenarios. The proposals in this paper, which are in the process of being implemented, could save the company operational expenditure while reducing the carbon footprint of the smelter.

  4. Future aircraft cabins and design thinking: optimisation vs. win-win scenarios

    Directory of Open Access Journals (Sweden)

    A. Hall

    2013-06-01

    Full Text Available With projections indicating an increase in mobility over the next few decades and annual flight departures expected to rise to over 16 billion by 2050, there is a demand for the aviation industry and associated stakeholders to consider new forms of aircraft and technology. Customer requirements are recognized as a key driver in business. The airline is the principal customer for the aircraft manufacture. The passenger is, in turn, the airline's principal customer but they are just one of several stakeholders that include aviation authorities, airport operators, air-traffic control and security agencies. The passenger experience is a key differentiator used by airlines to attract and retain custom and the fuselage that defines the cabin envelope for the in-flight passenger experience and cabin design therefore receives significant attention for new aircraft, service updates and refurbishments. Decision making in design is crucial to arriving at viable and worthwhile cabin formats. Too little innovation will result in an aircraft manufacturer and airlines using its products falling behind its competitors. Too much may result in an over-extension with, for example, use of immature technologies that do not have the necessary reliability for a safety critical industry or sufficient value to justify the development effort. The multiple requirements associated with cabin design, can be viewed as an area for optimisation, accepting trade-offs between the various parameters. Good design, however, is often defined as developing a concept that resolves the contradictions and takes the solution towards a win-win scenario. Indeed our understanding and practice of design allows for behaviors that enhance design thinking through divergence and convergence, the use of abductive reasoning, experimentation and systems thinking. This paper explores and defines the challenges of designing the aircraft cabin of the future that will deliver on the multiple

  5. Thickness Optimisation of Textiles Subjected to Heat and Mass Transport during Ironing

    Directory of Open Access Journals (Sweden)

    Korycki Ryszard

    2016-09-01

    Full Text Available Let us next analyse the coupled problem during ironing of textiles, that is, the heat is transported with mass whereas the mass transport with heat is negligible. It is necessary to define both physical and mathematical models. Introducing two-phase system of mass sorption by fibres, the transport equations are introduced and accompanied by the set of boundary and initial conditions. Optimisation of material thickness during ironing is gradient oriented. The first-order sensitivity of an arbitrary objective functional is analysed and included in optimisation procedure. Numerical example is the thickness optimisation of different textile materials in ironing device.

  6. Optimisation of NMR dynamic models II. A new methodology for the dual optimisation of the model-free parameters and the Brownian rotational diffusion tensor

    International Nuclear Information System (INIS)

    D'Auvergne, Edward J.; Gooley, Paul R.

    2008-01-01

    Finding the dynamics of an entire macromolecule is a complex problem as the model-free parameter values are intricately linked to the Brownian rotational diffusion of the molecule, mathematically through the autocorrelation function of the motion and statistically through model selection. The solution to this problem was formulated using set theory as an element of the universal set U-the union of all model-free spaces (d'Auvergne EJ and Gooley PR (2007) Mol BioSyst 3(7), 483-494). The current procedure commonly used to find the universal solution is to initially estimate the diffusion tensor parameters, to optimise the model-free parameters of numerous models, and then to choose the best model via model selection. The global model is then optimised and the procedure repeated until convergence. In this paper a new methodology is presented which takes a different approach to this diffusion seeded model-free paradigm. Rather than starting with the diffusion tensor this iterative protocol begins by optimising the model-free parameters in the absence of any global model parameters, selecting between all the model-free models, and finally optimising the diffusion tensor. The new model-free optimisation protocol will be validated using synthetic data from Schurr JM et al. (1994) J Magn Reson B 105(3), 211-224 and the relaxation data of the bacteriorhodopsin (1-36)BR fragment from Orekhov VY (1999) J Biomol NMR 14(4), 345-356. To demonstrate the importance of this new procedure the NMR relaxation data of the Olfactory Marker Protein (OMP) of Gitti R et al. (2005) Biochem 44(28), 9673-9679 is reanalysed. The result is that the dynamics for certain secondary structural elements is very different from those originally reported

  7. Optimising work practices to minimise the radiation exposure of PET radiopharmacists

    International Nuclear Information System (INIS)

    Hickson, K.; Chan, G.; O'Keefe, G.; Young, K.; Tochon-Danguy, H.; Poniger, S.; Scott, A.

    2010-01-01

    Full text: The recent installation of a new medical cyclotron at Austin Health has given justification to install an automatic radiopharmaceutical dispenser. We aimed to evaluate the effectiveness of the automatic radiopharmaceutical dispenser on the radiation exp sure of the PET radiopharmacist. Radiation measurements performed can be divided into two distinct examinations. These are; a survey of the ambient radiation levels and an estimation of the personal radiation dose to the radiopharmacist. Shielding around the automatic dispenser was modified and radiation levels were then compared pre and post optimisation. Using real time monitoring methods, the yearly projected radiation dose to the radiopharmacist for FOG production was found. For whole body exposure this was approximately 4.1 mSv per year and a dose of 221 mS v per year to the hands. The radiation dose burden from all duties was recorded using TLD's and was found to be 4.5 and 321 mSv for whole body and hand radiation doses respectively. Since the implementation of an automatic radiopharmaceutical dose dispenser, radiation exposure recorded to the hands by TLD measurements have fallen by 39%. Further optimisation has seen the ambient radiation levels fall by 15%. Conclusion It has been shown that by reviewing work practices, radiation exposure continues to remain below the radiation dose constraints required by law. Continuing optimization and reviewing ensures that radiation exposure is kept as low as reasonably achievable. (author)

  8. MANAGEMENT OPTIMISATION OF MASS CUSTOMISATION MANUFACTURING USING COMPUTATIONAL INTELLIGENCE

    Directory of Open Access Journals (Sweden)

    Louwrens Butler

    2018-05-01

    Full Text Available Computational intelligence paradigms can be used for advanced manufacturing system optimisation. A static simulation model of an advanced manufacturing system was developed in order to simulate a manufacturing system. The purpose of this advanced manufacturing system was to mass-produce a customisable product range at a competitive cost. The aim of this study was to determine whether this new algorithm could produce a better performance than traditional optimisation methods. The algorithm produced a lower cost plan than that for a simulated annealing algorithm, and had a lower impact on the workforce.

  9. Optimising Job-Shop Functions Utilising the Score-Function Method

    DEFF Research Database (Denmark)

    Nielsen, Erland Hejn

    2000-01-01

    During the last 1-2 decades, simulation optimisation of discrete event dynamic systems (DEDS) has made considerable theoretical progress with respect to computational efficiency. The score-function (SF) method and the infinitesimal perturbation analysis (IPA) are two candidates belonging to this ......During the last 1-2 decades, simulation optimisation of discrete event dynamic systems (DEDS) has made considerable theoretical progress with respect to computational efficiency. The score-function (SF) method and the infinitesimal perturbation analysis (IPA) are two candidates belonging...... of a Job-Shop can be handled by the SF method....

  10. HVAC system optimisation-in-building section

    Energy Technology Data Exchange (ETDEWEB)

    Lu, L.; Cai, W.; Xie, L.; Li, S.; Soh, Y.C. [School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore (Singapore)

    2004-07-01

    This paper presents a practical method to optimise in-building section of centralised Heating, Ventilation and Air-Conditioning (HVAC) systems which consist of indoor air loops and chilled water loops. First, through component characteristic analysis, mathematical models associated with cooling loads and energy consumption for heat exchangers and energy consuming devices are established. By considering variation of cooling load of each end user, adaptive neuro-fuzzy inference system (ANFIS) is employed to model duct and pipe networks and obtain optimal differential pressure (DP) set points based on limited sensor information. A mix-integer nonlinear constraint optimization of system energy is formulated and solved by a modified genetic algorithm. The main feature of our paper is a systematic approach in optimizing the overall system energy consumption rather than that of individual component. A simulation study for a typical centralized HVAC system is provided to compare the proposed optimisation method with traditional ones. The results show that the proposed method indeed improves the system performance significantly. (author)

  11. Pre-operative optimisation of lung function

    Directory of Open Access Journals (Sweden)

    Naheed Azhar

    2015-01-01

    Full Text Available The anaesthetic management of patients with pre-existing pulmonary disease is a challenging task. It is associated with increased morbidity in the form of post-operative pulmonary complications. Pre-operative optimisation of lung function helps in reducing these complications. Patients are advised to stop smoking for a period of 4–6 weeks. This reduces airway reactivity, improves mucociliary function and decreases carboxy-haemoglobin. The widely used incentive spirometry may be useful only when combined with other respiratory muscle exercises. Volume-based inspiratory devices have the best results. Pharmacotherapy of asthma and chronic obstructive pulmonary disease must be optimised before considering the patient for elective surgery. Beta 2 agonists, inhaled corticosteroids and systemic corticosteroids, are the main drugs used for this and several drugs play an adjunctive role in medical therapy. A graded approach has been suggested to manage these patients for elective surgery with an aim to achieve optimal pulmonary function.

  12. Acoustic Resonator Optimisation for Airborne Particle Manipulation

    Science.gov (United States)

    Devendran, Citsabehsan; Billson, Duncan R.; Hutchins, David A.; Alan, Tuncay; Neild, Adrian

    Advances in micro-electromechanical systems (MEMS) technology and biomedical research necessitate micro-machined manipulators to capture, handle and position delicate micron-sized particles. To this end, a parallel plate acoustic resonator system has been investigated for the purposes of manipulation and entrapment of micron sized particles in air. Numerical and finite element modelling was performed to optimise the design of the layered acoustic resonator. To obtain an optimised resonator design, careful considerations of the effect of thickness and material properties are required. Furthermore, the effect of acoustic attenuation which is dependent on frequency is also considered within this study, leading to an optimum operational frequency range. Finally, experimental results demonstrated good particle levitation and capture of various particle properties and sizes ranging to as small as 14.8 μm.

  13. European nuclear data studies for fast systems

    International Nuclear Information System (INIS)

    Rullhusen, P.; Hambsch, F.-J.; Mondelaers, W.; Plompen, A.J.M.; Schillebeeckx, P.

    2010-01-01

    Nuclear data needs for fast systems are highlighted and the following projects are described: Joint European research projects: MUSE Experiments for Sub-critical Neutronics Validation; High- and Intermediate Energy Nuclear Data for ADS (HINDAS); and the Time-Of-Flight facility for Nuclear Data Measurements for ADS (n T OF N D A DS); European Research Programme for the Transmutation of High Level Nuclear Waste in an Accelerator Driven System (EUROTRANS-NUDATRA); and CANDIDE; Programmes for transnational access to experimental facilities in Europe: European Facilities for Nuclear Data Measurements (EFNUDAT); Neutron Data Measurements at IRMM (NUDAME); European facility for innovative reactor and transmutation neutron data (EUFRAT) (P.A.)

  14. Optimisation of electrical system for offshore wind farms via genetic algorithm

    DEFF Research Database (Denmark)

    Chen, Zhe; Zhao, Menghua; Blaabjerg, Frede

    2009-01-01

    An optimisation platform based on genetic algorithm (GA) is presented, where the main components of a wind farm and key technical specifications are used as input parameters and the electrical system design of the wind farm is optimised in terms of both production cost and system reliability....... The power losses, wind power production, initial investment and maintenance costs are considered in the production cost. The availability of components and network redundancy are included in the reliability evaluation. The method of coding an electrical system to a binary string, which is processed by GA......, is developed. Different GA techniques are investigated based on a real example offshore wind farm. This optimisation platform has been demonstrated as a powerful tool for offshore wind farm design and evaluation....

  15. OPTIMISATION OF COMPRESSIVE STRENGTH OF PERIWINKLE ...

    African Journals Online (AJOL)

    In this paper, a regression model is developed to predict and optimise the compressive strength of periwinkle shell aggregate concrete using Scheffe's regression theory. The results obtained from the derived regression model agreed favourably with the experimental data. The model was tested for adequacy using a student ...

  16. Self-optimising control of sewer systems

    DEFF Research Database (Denmark)

    Mauricio Iglesias, Miguel; Montero-Castro, Ignacio; Mollerup, Ane Loft

    2013-01-01

    . The definition of an optimal performance was carried out by through a two-stage optimisation (stochastic and deterministic) to take into account both the overflow during the current rain event as well as the expected overflow, given the probability of a future rain event. The methodology is successfully applied...

  17. Multiobjective optimisation of energy systems and building envelope retrofit in a residential community

    International Nuclear Information System (INIS)

    Wu, Raphael; Mavromatidis, Georgios; Orehounig, Kristina; Carmeliet, Jan

    2017-01-01

    Highlights: • Simultaneous optimisation of building envelope retrofit and energy systems. • Retrofit and energy systems change interact and should be considered simultaneously. • Case study quantifies cost-GHG emission tradeoffs for different retrofit options. - Abstract: In this paper, a method for a multi-objective and simultaneous optimisation of building energy systems and retrofit is presented. Tailored to be suitable for the diverse range of existing buildings in terms of age, size, and use, it combines dynamic energy demand simulation to explore individual retrofit scenarios with an energy hub optimisation. Implemented as an epsilon-constrained mixed integer linear program (MILP), the optimisation matches envelope retrofit with renewable and high efficiency energy supply technologies such as biomass boilers, heat pumps, photovoltaic and solar thermal panels to minimise life cycle cost and greenhouse gas (GHG) emissions. Due to its multi-objective, integrated assessment of building transformation options and its ability to capture both individual building characteristics and trends within a neighbourhood, this method is aimed to provide developers, neighbourhood and town policy makers with the necessary information to make adequate decisions. Our method is deployed in a case study of typical residential buildings in the Swiss village of Zernez, simulating energy demands in EnergyPlus and solving the optimisation problem with CPLEX. Although common trade-offs in energy system and retrofit choice can be observed, optimisation results suggest that the diversity in building age and size leads to optimal strategies for retrofitting and building system solutions, which are specific to different categories. With this method, GHG emissions of the entire community can be reduced by up to 76% at a cost increase of 3% compared to the current emission levels, if an optimised solution is selected for each building category.

  18. Optimised low-dose multidetector CT protocol for children with cranial deformity

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez, Jose Luis [Complejo Hospitalario Universitario de Vigo, Department of Radiology, Vigo, Pontevedra (Spain); Pombar, Miguel Angel [Complejo Hospitalario Universitario de Santiago, Department of Radiophysics, Santiago de Compostela, La Coruna (Spain); Pumar, Jose Manuel [Complejo Hospitalario Universitario de Santiago, Department of Radiology, Santiago de Compostela, La Coruna (Spain); Campo, Victor Miguel del [Complejo Hospitalario Universitario de Vigo, Department of Public Health, Vigo, Pontevedra (Spain)

    2013-08-15

    To present an optimised low-dose multidetector computed tomography (MDCT) protocol for the study of children with cranial deformity. Ninety-one consecutive MDCT studies were performed in 80 children. Studies were performed with either our standard head CT protocol (group 1, n = 20) or a low-dose cranial deformity protocol (groups 2 and 3). Group 2 (n = 38), initial, and group 3 (n = 33), final and more optimised. All studies were performed in the same 64-MDCT equipment. Cranial deformity protocol was gradationally optimised decreasing kVp, limiting mA range, using automatic exposure control (AEC) and increasing the noise index (NI). Image quality was assessed. Dose indicators such us CT dose index volume (CTDIvol), dose-length product (DLP) and effective dose (E) were used. The optimised low-dose protocol reached the following values: 80 kVp, mA range: 50-150 and NI = 23. We achieved a maximum dose reduction of 10-22 times in the 1- to 12-month-old cranium in regard to the 2004 European guidelines for MDCT. A low-dose MDCT protocol that may be used as the first diagnostic imaging option in clinically selected patients with skull abnormalities. (orig.)

  19. Optimisation of the PCR-invA primers for the detection of Salmonella ...

    African Journals Online (AJOL)

    A polymerase chain reaction (PCR)-based method for the detection of Salmonella species in water samples was optimised and evaluated for speed, specificity and sensitivity. Optimisation of Mg2+ and primer concentrations and cycling parameters increased the sensitivity and limit of detection of PCR to 2.6 x 104 cfu/m.

  20. Thermodynamic optimisation of a heat exchanger

    NARCIS (Netherlands)

    Cornelissen, Rene; Hirs, Gerard

    1999-01-01

    The objective of this paper is to show that for the optimal design of an energy system, where there is a trade-off between exergy saving during operation and exergy use during construction of the energy system, exergy analysis and life cycle analysis should be combined. An exergy optimisation of a

  1. The international validation of bio- and chemical-anlaytical screening methods for dioxins and dioxin-like PCBs: the DIFFERENCE project rounds 1 and 2

    NARCIS (Netherlands)

    Loco, van J.; Leeuwen, van S.P.J.; Roos, P.; Carbonnelle, S.; Boer, de J.; Goeyens, L.; Beernaert, H.

    2004-01-01

    The European research project DIFFERENCE is focussed on the development, optimisation and validation of screening methods for dioxin analysis, including bio-analytical and chemical techniques (CALUX, GC-LRMS/MS, GC x GC-ECD) and on the optimisation and validation of new extraction and clean-up

  2. Advantages of Task-Specific Multi-Objective Optimisation in Evolutionary Robotics.

    Science.gov (United States)

    Trianni, Vito; López-Ibáñez, Manuel

    2015-01-01

    The application of multi-objective optimisation to evolutionary robotics is receiving increasing attention. A survey of the literature reveals the different possibilities it offers to improve the automatic design of efficient and adaptive robotic systems, and points to the successful demonstrations available for both task-specific and task-agnostic approaches (i.e., with or without reference to the specific design problem to be tackled). However, the advantages of multi-objective approaches over single-objective ones have not been clearly spelled out and experimentally demonstrated. This paper fills this gap for task-specific approaches: starting from well-known results in multi-objective optimisation, we discuss how to tackle commonly recognised problems in evolutionary robotics. In particular, we show that multi-objective optimisation (i) allows evolving a more varied set of behaviours by exploring multiple trade-offs of the objectives to optimise, (ii) supports the evolution of the desired behaviour through the introduction of objectives as proxies, (iii) avoids the premature convergence to local optima possibly introduced by multi-component fitness functions, and (iv) solves the bootstrap problem exploiting ancillary objectives to guide evolution in the early phases. We present an experimental demonstration of these benefits in three different case studies: maze navigation in a single robot domain, flocking in a swarm robotics context, and a strictly collaborative task in collective robotics.

  3. Advantages of Task-Specific Multi-Objective Optimisation in Evolutionary Robotics.

    Directory of Open Access Journals (Sweden)

    Vito Trianni

    Full Text Available The application of multi-objective optimisation to evolutionary robotics is receiving increasing attention. A survey of the literature reveals the different possibilities it offers to improve the automatic design of efficient and adaptive robotic systems, and points to the successful demonstrations available for both task-specific and task-agnostic approaches (i.e., with or without reference to the specific design problem to be tackled. However, the advantages of multi-objective approaches over single-objective ones have not been clearly spelled out and experimentally demonstrated. This paper fills this gap for task-specific approaches: starting from well-known results in multi-objective optimisation, we discuss how to tackle commonly recognised problems in evolutionary robotics. In particular, we show that multi-objective optimisation (i allows evolving a more varied set of behaviours by exploring multiple trade-offs of the objectives to optimise, (ii supports the evolution of the desired behaviour through the introduction of objectives as proxies, (iii avoids the premature convergence to local optima possibly introduced by multi-component fitness functions, and (iv solves the bootstrap problem exploiting ancillary objectives to guide evolution in the early phases. We present an experimental demonstration of these benefits in three different case studies: maze navigation in a single robot domain, flocking in a swarm robotics context, and a strictly collaborative task in collective robotics.

  4. Optimised Environmental Test Approaches in the GOCE Project

    Science.gov (United States)

    Ancona, V.; Giordano, P.; Casagrande, C.

    2004-08-01

    The Gravity Field and Steady-State Ocean Circulation Explorer (GOCE) is dedicated to measuring the Earth's gravity field and modelling the geoid with extremely high accuracy and spatial resolution. It is the first Earth Explorer Core mission to be developed as part of ESA's Living Planet Programme and is scheduled for launch in 2006. The program is managed by a consortium of European companies: Alenia Spazio, the prime contractor, Astrium GmbH, the platform responsible, Alcatel Space Industries and Laben, suppliers of the main payloads, respectively the Electrostatic Gravity Gradiometer (EGG) and the Satellite to Satellite Tracking Instrument (SSTI), actually a precise GPS receiver. The GOCE Assembly Integration and Verification (AIV) approach is established and implemented in order to demonstrate to the customer that the satellite design meets the applicable requirements and to qualify and accept from lower level up to system level. The driving keywords of "low cost" and "short schedule" program, call for minimizing the development effort by utilizing off-the-shelf equipment combined with a model philosophy lowering the number of models to be used. The paper will deal on the peculiarities of the optimized environmental test approach in the GOCE project. In particular it introduces the logic of the AIV approach and describe the foreseen tests at system level within the SM environmental test campaign, outlining the Quasi Static test performed in the frame of the SM sine vibration tests, and the PFM environmental test campaign pinpointing the deletion of the Sine Vibration test on PFM model. Furthermore the paper highlights how the Model and Test Effectiveness Database (MATD) can be utilized for the prediction of the new space projects like GOCE Satellite.

  5. Discussion on Implementation of ICRP Recommendations Concerning Reference Levels and Optimisation

    International Nuclear Information System (INIS)

    2013-02-01

    International Commission on Radiological Protection (ICRP) Publication 103, 'The 2007 Recommendations of the International Commission on Radiological Protection', issued in 2007, defines emergency exposure situations as unexpected situations that may require the implementation of urgent protective actions and perhaps longer term protective actions. The ICRP continues to recommend optimisation and the use of reference levels to ensure an adequate degree of protection in regard to exposure to ionising radiation in emergency exposure situations. Reference levels represent the level of dose or risk above which it is judged to be inappropriate to plan to allow exposures to occur and for which protective actions should therefore be planned and optimised. National authorities are responsible for establishing reference levels. The Expert Group on the Implementation of New International Recommendations for Emergency Exposure Situations (EGIRES) performed a survey to analyse the established processes for optimisation of the protection strategy for emergency exposure situations and for practical implementation of the reference level concept in several member states of the Nuclear Energy Agency (NEA). The EGIRES collected information on several national optimisation strategy definitions, on optimisation of protection for different protective actions, and also on optimisation of urgent protective actions. In addition, national criteria for setting reference levels, their use, and relevant processes, including specific triggers and dosimetric quantifies in setting reference levels, are focus points that the EGIRES also evaluated. The analysis of national responses to this 2011 survey shows many differences in the interpretation and application of the established processes and suggests that most countries are still in the early stages of implementing these processes. Since 2011, national authorities have continued their study of the ICRP recommendations to incorporate them into

  6. Critical Factors in Transnational Oil Companies Localisation Decisions - Clusters and Portfolio Optimisation

    International Nuclear Information System (INIS)

    Kind, Hans Jarle; Osmundsen, Petter; Tverteraas, Ragnar

    2001-10-01

    Enhanced understanding of the factors determining trans national companies' localisation decisions is important for regulators and other stake holders concerned about maintaining current activity levels in a petroleum producing country. This article discusses localisation decisions in the context of theories of industrial clusters and real portfolio optimisation theory (materiality), which we argue are two fruitful lines of explanation for trans national companies' behaviour. The industrial cluster literature is concerned about the level of positive externalities associated with geographic clustering of related production activities. The concept of materiality, implying that investment projects in an oil province must be of a certain minimum size in order to be interesting for oil companies, is evaluated empirically and compared to predictions of mainstream economic theory. (author)

  7. Design and Optimisation of a Simple Filter Group for Reactive Power Distribution

    Directory of Open Access Journals (Sweden)

    Ryszard Klempka

    2016-01-01

    Full Text Available Basic methods are presented to design a simple filter group and a method of shaping the resultant of the filter group’s impedance characteristics (distribution of the characteristics’ extremes and then project equations were transformed into a uniform, common form that addresses issues of the reactive power distribution between component filters. The analysis also takes into account the filters’ detuning from the reduced harmonics and quality factors of passive elements. Another important factor of the analysis considered was the power grid equivalent impedance affecting the filtration effectiveness. A criterion for the filter group’s filtration effectiveness evaluation was proposed and optimisation was completed for the reactive power distribution between separate filters in the function of the power grid’s equivalent inductance.

  8. Critical Factors in Transnational Oil Companies Localisation Decisions - Clusters and Portfolio Optimisation

    Energy Technology Data Exchange (ETDEWEB)

    Kind, Hans Jarle; Osmundsen, Petter; Tverteraas, Ragnar

    2001-10-01

    Enhanced understanding of the factors determining transnational companies' localisation decisions is important for regulators and other stakeholders concerned about maintaining current activity levels in a petroleum producing country. This article discusses localisation decisions in the context of theories of industrial clusters and real portfolio optimisation theory (materiality), which we argue are two fruitful lines of explanation for transnational companies' behaviour. The industrial cluster literature is concerned about the level of positive externalities associated with geographic clustering of related production activities. The concept of materiality, implying that investment projects in an oil province must be of a certain minimum size in order to be interesting for oil companies, is evaluated empirically and compared to predictions of mainstream economic theory. (author)

  9. Shape optimisation and performance analysis of flapping wings

    KAUST Repository

    Ghommem, Mehdi

    2012-09-04

    In this paper, shape optimisation of flapping wings in forward flight is considered. This analysis is performed by combining a local gradient-based optimizer with the unsteady vortex lattice method (UVLM). Although the UVLM applies only to incompressible, inviscid flows where the separation lines are known a priori, Persson et al. [1] showed through a detailed comparison between UVLM and higher-fidelity computational fluid dynamics methods for flapping flight that the UVLM schemes produce accurate results for attached flow cases and even remain trend-relevant in the presence of flow separation. As such, they recommended the use of an aerodynamic model based on UVLM to perform preliminary design studies of flapping wing vehicles Unlike standard computational fluid dynamics schemes, this method requires meshing of the wing surface only and not of the whole flow domain [2]. From the design or optimisation perspective taken in our work, it is fairly common (and sometimes entirely necessary, as a result of the excessive computational cost of the highest fidelity tools such as Navier-Stokes solvers) to rely upon such a moderate level of modelling fidelity to traverse the design space in an economical manner. The objective of the work, described in this paper, is to identify a set of optimised shapes that maximise the propulsive efficiency, defined as the ratio of the propulsive power over the aerodynamic power, under lift, thrust, and area constraints. The shape of the wings is modelled using B-splines, a technology used in the computer-aided design (CAD) field for decades. This basis can be used to smoothly discretize wing shapes with few degrees of freedom, referred to as control points. The locations of the control points constitute the design variables. The results suggest that changing the shape yields significant improvement in the performance of the flapping wings. The optimisation pushes the design to "bird-like" shapes with substantial increase in the time

  10. OPTIMISATION OF A DRIVE SYSTEM AND ITS EPICYCLIC GEAR SET

    OpenAIRE

    Bellegarde , Nicolas; Dessante , Philippe; Vidal , Pierre; Vannier , Jean-Claude

    2007-01-01

    International audience; This paper describes the design of a drive consisting of a DC motor, a speed reducer, a lead screw transformation system, a power converter and its associated DC source. The objective is to reduce the mass of the system. Indeed, the volume and weight optimisation of an electrical drive is an important issue for embedded applications. Here, we present an analytical model of the system in a specific application and afterwards an optimisation of the motor and speed reduce...

  11. Optimisation of gas-cooled reactors with the aid of mathematical computers

    Energy Technology Data Exchange (ETDEWEB)

    Margen, P H

    1959-04-15

    Reactor optimisation is the task of finding the combination of values of the independent variables in a reactor design producing the lowest cost of electricity. In a gas-cooled reactor the number of independent variables is particularly large and the optimisation process is, therefore, laborious. The present note describes a procedure for performing the entire optimisation procedure with the aid of a mathematical computer in a single operation, thus saving time for the design staff. Detailed equations and numerical constants are proposed for the thermal and cost relations involved. The reactor physics equations, on the other hand are merely stated as general functions of the relevant variables. The task of expressing these functions as detailed equations will be covered by separate documents prepared by the reactor physics department.

  12. Optimisation of gas-cooled reactors with the aid of mathematical computers

    International Nuclear Information System (INIS)

    Margen, P.H.

    1959-04-01

    Reactor optimisation is the task of finding the combination of values of the independent variables in a reactor design producing the lowest cost of electricity. In a gas-cooled reactor the number of independent variables is particularly large and the optimisation process is, therefore, laborious. The present note describes a procedure for performing the entire optimisation procedure with the aid of a mathematical computer in a single operation, thus saving time for the design staff. Detailed equations and numerical constants are proposed for the thermal and cost relations involved. The reactor physics equations, on the other hand are merely stated as general functions of the relevant variables. The task of expressing these functions as detailed equations will be covered by separate documents prepared by the reactor physics department

  13. Water distribution systems design optimisation using metaheuristics ...

    African Journals Online (AJOL)

    The topic of multi-objective water distribution systems (WDS) design optimisation using metaheuristics is investigated, comparing numerous modern metaheuristics, including several multi-objective evolutionary algorithms, an estimation of distribution algorithm and a recent hyperheuristic named AMALGAM (an evolutionary ...

  14. A national optimisation model for energy wood streams; Energiapuuvirtojen valtakunnallinen optimointimalli

    Energy Technology Data Exchange (ETDEWEB)

    Iikkanen, P.; Keskinen, S.; Korpilahti, A.; Raesaenen, T.; Sirkiae, A.

    2011-07-01

    In 2010 a total of 12,5 terawatt hours of forest energy was used in Finland's heat and power plants. According to studies by Metsaeteho and Poeyry, use of energy wood will nearly double to 21.6 terawatt hours by 2020. There are also plans to use energy wood as a raw material for biofuel plants. The techno-ecological supply potential of energy wood in 2020 is estimated at 42.9 terawatt hours. Energy wood has been transported almost entirely by road. The situation is changing, however, because growing demand for energy wood will expand raw wood procurement areas and lengthen transport distances. A cost-effective transport system therefore also requires the use of rail and waterway transports. In Finland, however, there is almost a complete absence of the terminals required for the use of rail and waterway transports; where energy wood is chipped, temporarily stored and loaded onto railway wagons and vessels for further transport. A national optimisation model for energy wood has been developed to serve transport system planning in particular. The linear optimisation model optimises, on a national level, goods streams between supply points and usage points based on forest energy procurement costs. The model simultaneously covers deliveries of forest chips, stumps and small-sized thinning wood. The procurement costs used in the optimisation include the costs of the energy wood's roadside price, chipping, transport and terminal handling. The transport system described in the optimisation model consists of wood supply points (2007 municipality precision), wood usage points, railway terminals and the connections between them along the main road and rail network. Elements required for the examination of waterway transports can also be easily added to the model. The optimisation model can be used to examine, for example, the effects of changes of energy wood demand and supply as well as transport costs on energy wood goods streams, the relative use of different

  15. Optimisation of window settings for traditional and noise-optimised virtual monoenergetic imaging in dual-energy computed tomography pulmonary angiography

    International Nuclear Information System (INIS)

    D'Angelo, Tommaso; ''G. Martino'' University Hospital, Messina; Bucher, Andreas M.; Lenga, Lukas; Arendt, Christophe T.; Peterke, Julia L.; Martin, Simon S.; Leithner, Doris; Vogl, Thomas J.; Wichmann, Julian L.; Caruso, Damiano; University Hospital, Latina; Mazziotti, Silvio; Blandino, Alfredo; Ascenti, Giorgio; University Hospital, Messina; Othman, Ahmed E.

    2018-01-01

    To define optimal window settings for displaying virtual monoenergetic images (VMI) of dual-energy CT pulmonary angiography (DE-CTPA). Forty-five patients who underwent clinically-indicated third-generation dual-source DE-CTPA were retrospectively evaluated. Standard linearly-blended (M 0 .6), 70-keV traditional VMI (M70), and 40-keV noise-optimised VMI (M40+) reconstructions were analysed. For M70 and M40+ datasets, the subjectively best window setting (width and level, B-W/L) was independently determined by two observers and subsequently related with pulmonary artery attenuation to calculate separate optimised values (O-W/L) using linear regression. Subjective evaluation of image quality (IQ) between W/L settings were assessed by two additional readers. Repeated measures of variance were performed to compare W/L settings and IQ indices between M 0 .6, M70, and M40+. B-W/L and O-W/L for M70 were 460/140 and 450/140, and were 1100/380 and 1070/380 for M40+, respectively, differing from standard DE-CTPA W/L settings (450/100). Highest subjective scores were observed for M40+ regarding vascular contrast, embolism demarcation, and overall IQ (all p<0.001). Application of O-W/L settings is beneficial to optimise subjective IQ of VMI reconstructions of DE-CTPA. A width slightly less than two times the pulmonary trunk attenuation and a level approximately of overall pulmonary vessel attenuation are recommended. (orig.)

  16. PREFACE: International Conference on Image Optimisation in Nuclear Medicine (OptiNM)

    Science.gov (United States)

    Christofides, Stelios; Parpottas, Yiannis

    2011-09-01

    Conference logo The International Conference on Image Optimisation in Nuclear Medicine was held at the Atlantica Aeneas Resort in Ayia Napa, Cyprus between 23-26 March 2011. It was organised in the framework of the research project "Optimising Diagnostic Value in SPECT Myocardial Perfusion Imaging" (YΓΕΙΑ/ΔYΓΕΙΑ/0308/11), funded by the Cyprus Research Promotion Foundation and the European Regional Development Fund, to present the highlights of the project, discuss the progress and results, and define future related goals. The aim of this International Conference was to concentrate on image optimization approaches in Nuclear Medicine. Experts in the field of nuclear medicine presented their latest research results, exchanged experiences and set future goals for image optimisation while balancing patient dose and diagnostic value. The conference was jointly organized by the Frederick Research Centre in Cyprus, the Department of Medical and Public Health Services of the Cyprus Ministry of Health, the Biomedical Research Foundation in Cyprus and the AGH University of Science and Technology in Poland. It was supported by the Cyprus Association of Medical Physics and Biomedical Engineering, and the Cyprus Society of Nuclear Medicine. The conference was held under the auspices of the European Federation of Organisations for Medical Physics and the European Association of Nuclear Medicine. The conference scientific programme covered several important topics such as functional imaging; image optimization; quantification for diagnosis; justification; simulations; patient dosimetry, staff exposures and radiation risks; quality assurance and clinical audit; education, training and radiation protection culture; hybrid systems and image registration; and new and competing technologies. The programme consisted of 13 invited and keynote presentations as well as workshops, round table discussions and a number of scientific sessions. A total of 51 speakers presented their

  17. Optimising the Target and Capture Sections of the Neutrino Factory

    CERN Document Server

    Hansen, Ole Martin; Stapnes, Steinar

    The Neutrino Factory is designed to produce an intense high energy neutrino beam from stored muons. The majority of the muons are obtained from the decay of pions, produced by a proton beam impinging on a free-flowing mercury-jet target and captured by a high magnetic field. It is important to capture a large fraction of the produced pions to maximize the intensity of the neutrino beam. Various optimisation studies have been performed with the aim of maximising the muon influx to the accelerator and thus the neutrino beam intensity. The optimisation studies were performed with the use of Monte Carlo simulation tools. The production of secondary particles, by interactions between the incoming proton beam and the mercury target, was optimised by varying the proton beam impact position and impact angles on the target. The proton beam and target interaction region was studied and showed to be off the central axis of the capture section in the baseline configuration. The off-centred interaction region resulted in ...

  18. Optimisation of surgical care for rectal cancer

    NARCIS (Netherlands)

    Borstlap, W.A.A.

    2017-01-01

    Optimisation of surgical care means weighing the risk of treatment related morbidity against the patients’ potential benefits of a surgical intervention. The first part of this thesis focusses on the anaemic patient undergoing colorectal surgery. Hypothesizing that a more profound haemoglobin

  19. An efficient optimisation method in groundwater resource ...

    African Journals Online (AJOL)

    DRINIE

    2003-10-04

    Oct 4, 2003 ... theories developed in the field of stochastic subsurface hydrology. In reality, many ... Recently, some researchers have applied the multi-stage ... Then a robust solution of the optimisation problem given by Eqs. (1) to (3) is as ...

  20. Thermodynamic optimisation and analysis of four Kalina cycle layouts for high temperature applications

    International Nuclear Information System (INIS)

    Modi, Anish; Haglind, Fredrik

    2015-01-01

    The Kalina cycle has seen increased interest in the last few years as an efficient alternative to the conventional steam Rankine cycle. However, the available literature gives little information on the algorithms to solve or optimise this inherently complex cycle. This paper presents a detailed approach to solve and optimise a Kalina cycle for high temperature (a turbine inlet temperature of 500 °C) and high pressure (over 100 bar) applications using a computationally efficient solution algorithm. A central receiver solar thermal power plant with direct steam generation was considered as a case study. Four different layouts for the Kalina cycle based on the number and/or placement of the recuperators in the cycle were optimised and compared based on performance parameters such as the cycle efficiency and the cooling water requirement. The cycles were modelled in steady state and optimised with the maximisation of the cycle efficiency as the objective function. It is observed that the different cycle layouts result in different regions for the optimal value of the turbine inlet ammonia mass fraction. Out of the four compared layouts, the most complex layout KC1234 gives the highest efficiency. The cooling water requirement is closely related to the cycle efficiency, i.e., the better the efficiency, the lower is the cooling water requirement. - Highlights: • Detailed methodology for solving and optimising Kalina cycle for high temperature applications. • A central receiver solar thermal power plant with direct steam generation considered as a case study. • Four Kalina cycle layouts based on the placement of recuperators optimised and compared

  1. Selecting a climate model subset to optimise key ensemble properties

    Directory of Open Access Journals (Sweden)

    N. Herger

    2018-02-01

    Full Text Available End users studying impacts and risks caused by human-induced climate change are often presented with large multi-model ensembles of climate projections whose composition and size are arbitrarily determined. An efficient and versatile method that finds a subset which maintains certain key properties from the full ensemble is needed, but very little work has been done in this area. Therefore, users typically make their own somewhat subjective subset choices and commonly use the equally weighted model mean as a best estimate. However, different climate model simulations cannot necessarily be regarded as independent estimates due to the presence of duplicated code and shared development history. Here, we present an efficient and flexible tool that makes better use of the ensemble as a whole by finding a subset with improved mean performance compared to the multi-model mean while at the same time maintaining the spread and addressing the problem of model interdependence. Out-of-sample skill and reliability are demonstrated using model-as-truth experiments. This approach is illustrated with one set of optimisation criteria but we also highlight the flexibility of cost functions, depending on the focus of different users. The technique is useful for a range of applications that, for example, minimise present-day bias to obtain an accurate ensemble mean, reduce dependence in ensemble spread, maximise future spread, ensure good performance of individual models in an ensemble, reduce the ensemble size while maintaining important ensemble characteristics, or optimise several of these at the same time. As in any calibration exercise, the final ensemble is sensitive to the metric, observational product, and pre-processing steps used.

  2. Selecting a climate model subset to optimise key ensemble properties

    Science.gov (United States)

    Herger, Nadja; Abramowitz, Gab; Knutti, Reto; Angélil, Oliver; Lehmann, Karsten; Sanderson, Benjamin M.

    2018-02-01

    End users studying impacts and risks caused by human-induced climate change are often presented with large multi-model ensembles of climate projections whose composition and size are arbitrarily determined. An efficient and versatile method that finds a subset which maintains certain key properties from the full ensemble is needed, but very little work has been done in this area. Therefore, users typically make their own somewhat subjective subset choices and commonly use the equally weighted model mean as a best estimate. However, different climate model simulations cannot necessarily be regarded as independent estimates due to the presence of duplicated code and shared development history. Here, we present an efficient and flexible tool that makes better use of the ensemble as a whole by finding a subset with improved mean performance compared to the multi-model mean while at the same time maintaining the spread and addressing the problem of model interdependence. Out-of-sample skill and reliability are demonstrated using model-as-truth experiments. This approach is illustrated with one set of optimisation criteria but we also highlight the flexibility of cost functions, depending on the focus of different users. The technique is useful for a range of applications that, for example, minimise present-day bias to obtain an accurate ensemble mean, reduce dependence in ensemble spread, maximise future spread, ensure good performance of individual models in an ensemble, reduce the ensemble size while maintaining important ensemble characteristics, or optimise several of these at the same time. As in any calibration exercise, the final ensemble is sensitive to the metric, observational product, and pre-processing steps used.

  3. Aspects of approximate optimisation: overcoming the curse of dimensionality and design of experiments

    NARCIS (Netherlands)

    Trichon, Sophie; Bonte, M.H.A.; Ponthot, Jean-Philippe; van den Boogaard, Antonius H.

    2007-01-01

    Coupling optimisation algorithms to Finite Element Methods (FEM) is a very promising way to achieve optimal metal forming processes. However, many optimisation algorithms exist and it is not clear which of these algorithms to use. This paper investigates the sensitivity of a Sequential Approximate

  4. Optimizing integrated reference cases in the OCTAVIUS project

    NARCIS (Netherlands)

    Kvamsdal, H.M.; Ehlers, S.; Kather, A.; Khakharia, P.M.; Nienoord, M.; Fosbøl, P.L.

    2016-01-01

    Adding a carbon capture plant to a power plant reduces the efficiency of said power plant. In order to keep this drop in efficiency as small as possible, several optimisation studies are performed in the OCTAVIUS project. Based on the work of the European Benchmarking Task Force-EBTF within the

  5. An Optimised Method to Determine PAHs in a Contaminated Soil; Metodo Optimizado para la Determinacion de PAHs en un Suelo Contaminado

    Energy Technology Data Exchange (ETDEWEB)

    Garcia Alonso, S.; Perez Pastor, R. M.; Sevillano castano, M. L.; Escolano Segovia, O.; Garcia Frutos, F. J.

    2007-07-20

    An analytical study is presented based on an optimised method to determine selected polycyclic aromatic hydrocarbons (PAHs) by High Performance Liquid Chromatography (HPLC) with fluorescence detection. The work was focused to obtain reliable measurements of PAH in a gas work contaminated soil and was performed in the frame of the project 'Assessment of natural remediation technologies for PAHs in contaminated soils' (Spanish Plan Nacional l+D+i, CTM 2004-05832-CO2-01): First assays were focused to evaluate an initial proposed procedure by sonication extraction in the contaminated soil. Afterwards to extend the efficiency and reduce solvent and time consuming of extraction procedures, the more relevant parameters that affect the extraction step were investigated. A comparison between sonication and microwave procedures was done, and the influence of sample grinding was studied. In general, both extraction techniques led on comparable results, although sonication procedure needs to be more carefully optimised. Finally, as a final application of the optimised method, the effect of particle size on relative distribution of selected PAHs in the contaminated soil was investigated. Relative abundance of more volatile PAHs showed a decreasing according to lower grain size, while relative abundance of less volatile compounds indicated an increasing of concentration levels for lower grain size. (Author) 10 refs.

  6. Status of achievements reached in applying optimisation of protection in prevention and mitigation of accidents in nuclear facilities

    International Nuclear Information System (INIS)

    Bengtsson, G.; Hoegberg, L.

    1988-01-01

    Optimisation of protection in a broad sense is basically a political undertaking, where the resources put into protection are balanced against other factors - quantifiable and non-quantifiable - to obtain the best protection that can be achieved under the circumstances. In a narrower sense, optimisation can be evaluated in procedures allowing for a few quantifiable factors, such as cost/effectiveness analysis. These procedures are used as inputs to the broader optimisation. The paper discusses several examples from Sweden concerning evaluations and decisions relating to prevention of accidents and mitigation of their consequences. Comparison is made with typical optimisation criteria proposed for radiation protection work and for cost/effective analysis in the USA, notably NUREG-1150 (draft). The examples show that optimisation procedures in a narrower sense have not been decisive. Individual dose limits seem to be increasingly important as compared to collective dose optimisation, and political, commercial or engineering judgements may lead to decisions far away from those suggested by simple optimisation considerations

  7. Approaches and challenges to optimising primary care teams’ electronic health record usage

    Directory of Open Access Journals (Sweden)

    Nancy Pandhi

    2014-07-01

    Full Text Available Background Although the presence of an electronic health record (EHR alone does not ensure high quality, efficient care, few studies have focused on the work of those charged with optimising use of existing EHR functionality.Objective To examine the approaches used and challenges perceived by analysts supporting the optimisation of primary care teams’ EHR use at a large U.S. academic health care system.Methods A qualitative study was conducted. Optimisation analysts and their supervisor were interviewed and data were analysed for themes.Results Analysts needed to reconcile the tension created by organisational mandates focused on the standardisation of EHR processes with the primary care teams’ demand for EHR customisation. They gained an understanding of health information technology (HIT leadership’s and primary care team’s goals through attending meetings, reading meeting minutes and visiting with clinical teams. Within what was organisationally possible, EHR education could then be tailored to fit team needs. Major challenges were related to organisational attempts to standardise EHR use despite varied clinic contexts, personnel readiness and technical issues with the EHR platform. Forcing standardisation upon clinical needs that current EHR functionality could not satisfy was difficult.Conclusions Dedicated optimisation analysts can add value to health systems through playing a mediating role between HIT leadership and care teams. Our findings imply that EHR optimisation should be performed with an in-depth understanding of the workflow, cognitive and interactional activities in primary care.

  8. Effectiveness of an implementation optimisation intervention aimed at increasing parent engagement in HENRY, a childhood obesity prevention programme - the Optimising Family Engagement in HENRY (OFTEN) trial: study protocol for a randomised controlled trial.

    Science.gov (United States)

    Bryant, Maria; Burton, Wendy; Cundill, Bonnie; Farrin, Amanda J; Nixon, Jane; Stevens, June; Roberts, Kim; Foy, Robbie; Rutter, Harry; Hartley, Suzanne; Tubeuf, Sandy; Collinson, Michelle; Brown, Julia

    2017-01-24

    Family-based interventions to prevent childhood obesity depend upon parents' taking action to improve diet and other lifestyle behaviours in their families. Programmes that attract and retain high numbers of parents provide an enhanced opportunity to improve public health and are also likely to be more cost-effective than those that do not. We have developed a theory-informed optimisation intervention to promote parent engagement within an existing childhood obesity prevention group programme, HENRY (Health Exercise Nutrition for the Really Young). Here, we describe a proposal to evaluate the effectiveness of this optimisation intervention in regard to the engagement of parents and cost-effectiveness. The Optimising Family Engagement in HENRY (OFTEN) trial is a cluster randomised controlled trial being conducted across 24 local authorities (approximately 144 children's centres) which currently deliver HENRY programmes. The primary outcome will be parental enrolment and attendance at the HENRY programme, assessed using routinely collected process data. Cost-effectiveness will be presented in terms of primary outcomes using acceptability curves and through eliciting the willingness to pay for the optimisation from HENRY commissioners. Secondary outcomes include the longitudinal impact of the optimisation, parent-reported infant intake of fruits and vegetables (as a proxy to compliance) and other parent-reported family habits and lifestyle. This innovative trial will provide evidence on the implementation of a theory-informed optimisation intervention to promote parent engagement in HENRY, a community-based childhood obesity prevention programme. The findings will be generalisable to other interventions delivered to parents in other community-based environments. This research meets the expressed needs of commissioners, children's centres and parents to optimise the potential impact that HENRY has on obesity prevention. A subsequent cluster randomised controlled pilot

  9. EUROPART: an European integrated project on actinide partitioning

    International Nuclear Information System (INIS)

    Madic, C.; Baron, P.; Hudson, M.J.

    2006-01-01

    Full text of publication follows: The EUROPART project is a scientific integrated project between 24 European partners, from 10 countries, mostly funded by the European Community within the FP6, together with CRIEPI from Japan and ANSTO from Australia. EUROPART aims at developing chemical partitioning processes for the so-called minor actinides (MA) contained in nuclear wastes, i.e. from Am to Cf. In the case of the treatment of dedicated spent fuels or targets, the actinides to be separated also include U, Pu and Np. The techniques considered for the separation of these radionuclides belong to the fields of hydrometallurgy and pyrometallurgy, as in the previous European FP5 programs named PARTNEW, CALIXPART and PYROREP, respectively. The two main axes of research within EUROPART are: 1/ the partitioning of MA (from Am to Cf) from wastes issuing from the reprocessing of high burn-up UOX fuels and multi-recycled MOX fuels, 2/ the partitioning of the whole actinide family of elements for recycling, as an option for advanced dedicated fuel cycles (this work will be connected to the studies to be performed within the EUROTRANS European integrated project). In hydrometallurgy, the research is organized in five Work Packages (WP). Four are dedicated to the study of partitioning methods mainly based on the use of solvent extraction methods and of solid extractants, one WP is dedicated to the development of actinide co-conversion methods for fuel or target preparations. The research in pyrometallurgy is organized into four WPs, listed hereafter: (i) study of the basic chemistry of transuranium elements and of some fission products in molten salts (chlorides, fluorides), (ii) development of actinide partitioning methods, (iii) study of the conditioning of the salt wastes, (iv) system studies. Moreover, a strong management team is concerned not only with the technical and financial issues arising from EUROPART, but also with information, communication and benefits for Europe

  10. Pre-segmented 2-Step IMRT with subsequent direct machine parameter optimisation – a planning study

    International Nuclear Information System (INIS)

    Bratengeier, Klaus; Meyer, Jürgen; Flentje, Michael

    2008-01-01

    Modern intensity modulated radiotherapy (IMRT) mostly uses iterative optimisation methods. The integration of machine parameters into the optimisation process of step and shoot leaf positions has been shown to be successful. For IMRT segmentation algorithms based on the analysis of the geometrical structure of the planning target volumes (PTV) and the organs at risk (OAR), the potential of such procedures has not yet been fully explored. In this work, 2-Step IMRT was combined with subsequent direct machine parameter optimisation (DMPO-Raysearch Laboratories, Sweden) to investigate this potential. In a planning study DMPO on a commercial planning system was compared with manual primary 2-Step IMRT segment generation followed by DMPO optimisation. 15 clinical cases and the ESTRO Quasimodo phantom were employed. Both the same number of optimisation steps and the same set of objective values were used. The plans were compared with a clinical DMPO reference plan and a traditional IMRT plan based on fluence optimisation and consequent segmentation. The composite objective value (the weighted sum of quadratic deviations of the objective values and the related points in the dose volume histogram) was used as a measure for the plan quality. Additionally, a more extended set of parameters was used for the breast cases to compare the plans. The plans with segments pre-defined with 2-Step IMRT were slightly superior to DMPO alone in the majority of cases. The composite objective value tended to be even lower for a smaller number of segments. The total number of monitor units was slightly higher than for the DMPO-plans. Traditional IMRT fluence optimisation with subsequent segmentation could not compete. 2-Step IMRT segmentation is suitable as starting point for further DMPO optimisation and, in general, results in less complex plans which are equal or superior to plans generated by DMPO alone

  11. A method to derive fixed budget results from expected optimisation times

    DEFF Research Database (Denmark)

    Doerr, Benjamin; Jansen, Thomas; Witt, Carsten

    2013-01-01

    At last year's GECCO a novel perspective for theoretical performance analysis of evolutionary algorithms and other randomised search heuristics was introduced that concentrates on the expected function value after a pre-defined number of steps, called budget. This is significantly different from...... the common perspective where the expected optimisation time is analysed. While there is a huge body of work and a large collection of tools for the analysis of the expected optimisation time the new fixed budget perspective introduces new analytical challenges. Here it is shown how results on the expected...... optimisation time that are strengthened by deviation bounds can be systematically turned into fixed budget results. We demonstrate our approach by considering the (1+1) EA on LeadingOnes and significantly improving previous results. We prove that deviating from the expected time by an additive term of ω(n3...

  12. Optimisation of water chemistry to ensure reliable water reactor fuel performance at high burnup and in ageing plant (FUWAC): an International Atomic Energy Agency coordinated research project

    Energy Technology Data Exchange (ETDEWEB)

    Killeen, J.C. [International Atomic Energy Agency, Vienna (Austria); Nordmann, F. [Advanced Nuclear Technology International Europe AB, Beauchamp (France); Schunk, J. [Paks NPP (Hungary); Vonkova, K. [Nuclear Research Inst., Rez (Czech Republic)

    2010-07-01

    The IAEA project 'Optimisation of Water Chemistry to ensure Reliable Water Reactor Fuel Performance at High Burnup and in Aging Plant' (FUWAC) was initiated with the objectives of monitoring, maintaining and optimising water chemistry regimes in primary circuits of water cooled power reactors, taking into account high burnup operation, mixed cores and plant aging, including following issues and remedies. This report provides some highlights of the work undertaken by the project participants. Clad oxidation studies have been undertaken and include operational data from the South Ukraine WWER where no corrosion problems have been seen on either Westinghouse ZIRLO™ or Russian alloy E110 fuel cladding. Work on the Russian alloy E110 showed that potassium in the coolant is preferable to lithium for mitigating fuel cladding oxidation. Studies on crud behaviour in PWR have shown a dependence on crud thickness and pHT. The nature and mechanisms for boron deposition in fuel cladding cruds have been investigated which is the root cause of crud induced power shifts (CIPS). Operational experience at French PWRs shows no difference in the CIPS behaviour between units with Alloy 600 or 690 steam generators, whilst Korean experience provides information on the Ni/Fe ratio on fuel cladding crud and the occurrence of CIPS. Coolant additions have been studied, for example in BWR units using zinc addition, crud is more tenacious. Zinc is also added to PWR units, mainly for dose rate control and in some cases for PWSCC mitigation of Alloy 600. At low levels there has been no clear evidence of any effect of zinc on CIPS, but there is a benefit on fuel oxidation. It is suggested that zinc addition should be considered where there is SG replacement or fuel core management modification. One possibility for the elimination of fuel crud is decontamination. Such an operation is time consuming, expensive, includes several risks of corrosion and induces a large quantity of

  13. Shape optimisation and performance analysis of flapping wings

    KAUST Repository

    Ghommem, Mehdi; Collier, Nathan; Niemi, Antti; Calo, Victor M.

    2012-01-01

    optimised shapes produce efficient flapping flights, the wake pattern and its vorticity strength are examined. This work described in this paper should facilitate better guidance for shape design of engineered flying systems.

  14. Numerical optimisation of friction stir welding: review of future challenges

    DEFF Research Database (Denmark)

    Tutum, Cem Celal; Hattel, Jesper Henri

    2011-01-01

    During the last decade, the combination of increasingly more advanced numerical simulation software with high computational power has resulted in models for friction stir welding (FSW), which have improved the understanding of the determining physical phenomena behind the process substantially....... This has made optimisation of certain process parameters possible and has in turn led to better performing friction stir welded products, thus contributing to a general increase in the popularity of the process and its applications. However, most of these optimisation studies do not go well beyond manual...

  15. Optimising Comprehensibility in Interlingual Translation

    DEFF Research Database (Denmark)

    Nisbeth Jensen, Matilde

    2015-01-01

    The increasing demand for citizen engagement in areas traditionally belonging exclusively to experts, such as health, law and technology has given rise to the necessity of making expert knowledge available to the general public through genres such as instruction manuals for consumer goods, patien...... the functional text type of Patient Information Leaflet. Finally, the usefulness of applying the principles of Plain Language and intralingual translation for optimising comprehensibility in interlingual translation is discussed....

  16. On optimal development and becoming an optimiser

    NARCIS (Netherlands)

    de Ruyter, D.J.

    2012-01-01

    The article aims to provide a justification for the claim that optimal development and becoming an optimiser are educational ideals that parents should pursue in raising their children. Optimal development is conceptualised as enabling children to grow into flourishing persons, that is persons who

  17. Day-ahead economic optimisation of energy storage

    NARCIS (Netherlands)

    Lampropoulos, I.; Garoufalis, P.; Bosch, van den P.P.J.; Groot, de R.J.W.; Kling, W.L.

    2014-01-01

    This article addresses the day-ahead economic optimisation of energy storage systems within the setting of electricity spot markets. The case study is about a lithium-ion battery system integrated in a low voltage distribution grid with residential customers and photovoltaic generation in the

  18. Optimisation of the formulation of a bubble bath by a chemometric approach market segmentation and optimisation.

    Science.gov (United States)

    Marengo, Emilio; Robotti, Elisa; Gennaro, Maria Carla; Bertetto, Mariella

    2003-03-01

    The optimisation of the formulation of a commercial bubble bath was performed by chemometric analysis of Panel Tests results. A first Panel Test was performed to choose the best essence, among four proposed to the consumers; the best essence chosen was used in the revised commercial bubble bath. Afterwards, the effect of changing the amount of four components (the amount of primary surfactant, the essence, the hydratant and the colouring agent) of the bubble bath was studied by a fractional factorial design. The segmentation of the bubble bath market was performed by a second Panel Test, in which the consumers were requested to evaluate the samples coming from the experimental design. The results were then treated by Principal Component Analysis. The market had two segments: people preferring a product with a rich formulation and people preferring a poor product. The final target, i.e. the optimisation of the formulation for each segment, was obtained by the calculation of regression models relating the subjective evaluations given by the Panel and the compositions of the samples. The regression models allowed to identify the best formulations for the two segments ofthe market.

  19. Optimising Transport Decision Making using Customised Decision Models and Decision Conferences

    DEFF Research Database (Denmark)

    Barfod, Michael Bruhn

    The subject of this Ph.D. thesis entitled “Optimising Transport Decision Making using Customised Decision Models and Decision Conferences” is multi-criteria decision analysis (MCDA) and decision support in the context of transport infrastructure assessments. Despite the fact that large amounts...... is concerned with the insufficiency of conventional cost-benefit analysis (CBA), and proposes the use of MCDA as a supplementing tool in order to also capture impacts of a more strategic character in the appraisals and hence make more use of the often large efforts put in the preliminary examinations. MCDA...... and rail to bike transport projects. Two major concerns have been to propose an examination process that can be used in situations where complex decision problems need to be addressed by experts as well as non-experts in decision making, and to identify appropriate assessment techniques to be used...

  20. Optimal sampling plan for clean development mechanism lighting projects with lamp population decay

    International Nuclear Information System (INIS)

    Ye, Xianming; Xia, Xiaohua; Zhang, Jiangfeng

    2014-01-01

    Highlights: • A metering cost minimisation model is built with the lamp population decay to optimise CDM lighting projects sampling plan. • The model minimises the total metering cost and optimise the annual sample size during the crediting period. • The required 90/10 criterion sampling accuracy is satisfied for each CDM monitoring report. - Abstract: This paper proposes a metering cost minimisation model that minimises metering cost under the constraints of sampling accuracy requirement for clean development mechanism (CDM) energy efficiency (EE) lighting project. Usually small scale (SSC) CDM EE lighting projects expect a crediting period of 10 years given that the lighting population will decay as time goes by. The SSC CDM sampling guideline requires that the monitored key parameters for the carbon emission reduction quantification must satisfy the sampling accuracy of 90% confidence and 10% precision, known as the 90/10 criterion. For the existing registered CDM lighting projects, sample sizes are either decided by professional judgment or by rule-of-thumb without considering any optimisation. Lighting samples are randomly selected and their energy consumptions are monitored continuously by power meters. In this study, the sampling size determination problem is formulated as a metering cost minimisation model by incorporating a linear lighting decay model as given by the CDM guideline AMS-II.J. The 90/10 criterion is formulated as constraints to the metering cost minimisation problem. Optimal solutions to the problem minimise the metering cost whilst satisfying the 90/10 criterion for each reporting period. The proposed metering cost minimisation model is applicable to other CDM lighting projects with different population decay characteristics as well

  1. The optimization of treatment and management of schizophrenia in Europe (OPTiMiSE) trial

    DEFF Research Database (Denmark)

    Leucht, Stefan; Winter-van Rossum, Inge; Heres, Stephan

    2015-01-01

    Commission sponsored "Optimization of Treatment and Management of Schizophrenia in Europe" (OPTiMiSE) trial which aims to provide a treatment algorithm for patients with a first episode of schizophrenia. METHODS: We searched Pubmed (October 29, 2014) for randomized controlled trials (RCTs) that examined...... switching the drug in nonresponders to another antipsychotic. We described important methodological choices of the OPTiMiSE trial. RESULTS: We found 10 RCTs on switching antipsychotic drugs. No trial was conclusive and none was concerned with first-episode schizophrenia. In OPTiMiSE, 500 first episode...

  2. Optimisation of the level-1 calorimeter trigger at ATLAS for Run II

    Energy Technology Data Exchange (ETDEWEB)

    Suchek, Stanislav [Kirchhoff-Institute for Physics, Im Neuenheimer Feld 227, 69120 Heidelberg (Germany); Collaboration: ATLAS-Collaboration

    2015-07-01

    The Level-1 Calorimeter Trigger (L1Calo) is a central part of the ATLAS Level-1 Trigger system, designed to identify jet, electron, photon, and hadronic tau candidates, and to measure their transverse energies, as well total transverse energy and missing transverse energy. The optimisation of the jet energy resolution is an important part of the L1Calo upgrade for Run II. A Look-Up Table (LUT) is used to translate the electronic signal from each trigger tower to its transverse energy. By optimising the LUT calibration we can achieve better jet energy resolution and better performance of the jet transverse energy triggers, which are vital for many physics analyses. In addition, the improved energy calibration leads to significant improvements of the missing transverse energy resolution. A new Multi-Chip Module (MCM), as a part of the L1Calo upgrade, provides two separate LUTs for jets and electrons/photons/taus, allowing to optimise jet transverse energy and missing transverse energy separately from the electromagnetic objects. The optimisation is validated using jet transverse energy and missing transverse energy triggers turn-on curves and rates.

  3. Balanced the Trade-offs problem of ANFIS Using Particle Swarm Optimisation

    Directory of Open Access Journals (Sweden)

    Dian Palupi Rini

    2013-11-01

    Full Text Available Improving the approximation accuracy and interpretability of fuzzy systems is an important issue either in fuzzy systems theory or in its applications . It is known that simultaneous optimisation both issues was the trade-offs problem, but it will improve performance of the system and avoid overtraining of data. Particle swarm optimisation (PSO is part of evolutionary algorithm that is good candidate algorithms to solve multiple optimal solution and better global search space. This paper introduces an integration of PSO dan ANFIS for optimise its learning especially for tuning membership function parameters and finding the optimal rule for better classification. The proposed method has been tested on four standard dataset from UCI machine learning i.e. Iris Flower, Habermans Survival Data, Balloon and Thyroid dataset. The results have shown better classification using the proposed PSO-ANFIS and the time complexity has reduced accordingly.

  4. Portfolio optimisation for hydropower producers that balances riverine ecosystem protection and producer needs

    Science.gov (United States)

    Yin, X. A.; Yang, Z. F.; Liu, C. L.

    2014-04-01

    In deregulated electricity markets, hydropower portfolio design has become an essential task for producers. The previous research on hydropower portfolio optimisation focused mainly on the maximisation of profits but did not take into account riverine ecosystem protection. Although profit maximisation is the major objective for producers in deregulated markets, protection of riverine ecosystems must be incorporated into the process of hydropower portfolio optimisation, especially against a background of increasing attention to environmental protection and stronger opposition to hydropower generation. This research seeks mainly to remind hydropower producers of the requirement of river protection when they design portfolios and help shift portfolio optimisation from economically oriented to ecologically friendly. We establish a framework to determine the optimal portfolio for a hydropower reservoir, accounting for both economic benefits and ecological needs. In this framework, the degree of natural flow regime alteration is adopted as a constraint on hydropower generation to protect riverine ecosystems, and the maximisation of mean annual revenue is set as the optimisation objective. The electricity volumes assigned in different electricity submarkets are optimised by the noisy genetic algorithm. The proposed framework is applied to China's Wangkuai Reservoir to test its effectiveness. The results show that the new framework could help to design eco-friendly portfolios that can ensure a planned profit and reduce alteration of the natural flow regime.

  5. User-inspired design methodology using Affordance Structure Matrix (ASM) for construction projects

    OpenAIRE

    Maheswari J. Uma; Charlesraj V. Paul C.; Battacharya Soma

    2017-01-01

    Traditionally, design phase of construction projects is often performed with incomplete and inaccurate user preferences. This is due to inefficiencies in the methodologies used for capturing the user requirements that can subsequently lead to inconsistencies and result in non-optimised end-result. Iterations and subsequent reworks due to such design inefficiencies is one of the major reasons for unsuccessful project delivery as they impact project performance measures such as time and cost am...

  6. Optimised cantilever biosensor with piezoresistive read-out

    DEFF Research Database (Denmark)

    Rasmussen, Peter; Thaysen, J.; Hansen, Ole

    2003-01-01

    We present a cantilever-based biochemical sensor with piezoresistive read-out which has been optimised for measuring surface stress. The resistors and the electrical wiring on the chip are encapsulated in low-pressure chemical vapor deposition (LPCVD) silicon nitride, so that the chip is well sui...

  7. The impact of energy efficiency interventions on industry – the Industrial Energy Efficiency Project in South Africa

    CSIR Research Space (South Africa)

    Hartzenburg, A

    2015-10-01

    Full Text Available The IEE Project was set up in 2010 to help transform the energy-use patterns of South African industry by means of energy management systems and energy systems optimisation. Through IEE Project implementation, around 100 industry plants have saved 1...

  8. Development and optimisation of synthesis, characterisation and physical properties of solid materials for strip conductors; purpose oriented synthesis of novel systems. Final report

    International Nuclear Information System (INIS)

    Guenther, W.; Schoellhorn, R.

    1995-06-01

    The project reported is part of studies into the performance of HTSC, and was responsible for the following essential tasks: synthesis, characterisation, and optimisation of oxocuprates of the type (RE)Ba 2 Cu 3 O 7 , examination of the relevant corrosion processes and reactivity of the phases, and synthesis of novel systems guided by special model concepts, applying kinetics-controlled low-temperature synthesis. (orig./MM) [de

  9. Optimised operation of an off-grid hybrid wind-diesel-battery system using genetic algorithm

    International Nuclear Information System (INIS)

    Gan, Leong Kit; Shek, Jonathan K.H.; Mueller, Markus A.

    2016-01-01

    Highlights: • Diesel generator’s operation is optimised in a hybrid wind-diesel-battery system. • Optimisation is performed using wind speed and load demand forecasts. • The objective is to maximise wind energy utilisation with limited battery storage. • Physical modelling approach (Simscape) is used to verify mathematical model. • Sensitivity analyses are performed with synthesised wind and load forecast errors. - Abstract: In an off-grid hybrid wind-diesel-battery system, the diesel generator is often not utilised efficiently, therefore compromising its lifetime. In particular, the general rule of thumb of running the diesel generator at more than 40% of its rated capacity is often unmet. This is due to the variation in power demand and wind speed which needs to be supplied by the diesel generator. In addition, the frequent start-stop of the diesel generator leads to additional mechanical wear and fuel wastage. This research paper proposes a novel control algorithm which optimises the operation of a diesel generator, using genetic algorithm. With a given day-ahead forecast of local renewable energy resource and load demand, it is possible to optimise the operation of a diesel generator, subjected to other pre-defined constraints. Thus, the utilisation of the renewable energy sources to supply electricity can be maximised. Usually, the optimisation studies of a hybrid system are being conducted through simple analytical modelling, coupled with a selected optimisation algorithm to seek the optimised solution. The obtained solution is not verified using a more realistic system model, for instance the physical modelling approach. This often led to the question of the applicability of such optimised operation being used in reality. In order to take a step further, model-based design using Simulink is employed in this research to perform a comparison through a physical modelling approach. The Simulink model has the capability to incorporate the electrical

  10. Optimisation Study on the Production of Anaerobic Digestate ...

    African Journals Online (AJOL)

    DR. AMIN

    optimise the production of ADC from organic fractions of domestic wastes and the effects of ADC amendments on soil .... (22%), cooked meat (9%), lettuce (11%), carrots. (3%), potato (44%) ... seed was obtained from a mesophilic anaerobic.

  11. Optimisation of decision making under uncertainty throughout field lifetime: A fractured reservoir example

    Science.gov (United States)

    Arnold, Dan; Demyanov, Vasily; Christie, Mike; Bakay, Alexander; Gopa, Konstantin

    2016-10-01

    Assessing the change in uncertainty in reservoir production forecasts over field lifetime is rarely undertaken because of the complexity of joining together the individual workflows. This becomes particularly important in complex fields such as naturally fractured reservoirs. The impact of this problem has been identified in previous and many solutions have been proposed but never implemented on complex reservoir problems due to the computational cost of quantifying uncertainty and optimising the reservoir development, specifically knowing how many and what kind of simulations to run. This paper demonstrates a workflow that propagates uncertainty throughout field lifetime, and into the decision making process by a combination of a metric-based approach, multi-objective optimisation and Bayesian estimation of uncertainty. The workflow propagates uncertainty estimates from appraisal into initial development optimisation, then updates uncertainty through history matching and finally propagates it into late-life optimisation. The combination of techniques applied, namely the metric approach and multi-objective optimisation, help evaluate development options under uncertainty. This was achieved with a significantly reduced number of flow simulations, such that the combined workflow is computationally feasible to run for a real-field problem. This workflow is applied to two synthetic naturally fractured reservoir (NFR) case studies in appraisal, field development, history matching and mid-life EOR stages. The first is a simple sector model, while the second is a more complex full field example based on a real life analogue. This study infers geological uncertainty from an ensemble of models that are based on the carbonate Brazilian outcrop which are propagated through the field lifetime, before and after the start of production, with the inclusion of production data significantly collapsing the spread of P10-P90 in reservoir forecasts. The workflow links uncertainty

  12. Geometrical exploration of a flux-optimised sodium receiver through multi-objective optimisation

    Science.gov (United States)

    Asselineau, Charles-Alexis; Corsi, Clothilde; Coventry, Joe; Pye, John

    2017-06-01

    A stochastic multi-objective optimisation method is used to determine receiver geometries with maximum second law efficiency, minimal average temperature and minimal surface area. The method is able to identify a set of Pareto optimal candidates that show advantageous geometrical features, mainly in being able to maximise the intercepted flux within the geometrical boundaries set. Receivers with first law thermal efficiencies ranging from 87% to 91% are also evaluated using the second law of thermodynamics and found to have similar efficiencies of over 60%, highlighting the influence that the geometry can play in the maximisation of the work output of receivers by influencing the distribution of the flux from the concentrator.

  13. Particle Swarm Optimisation with Spatial Particle Extension

    DEFF Research Database (Denmark)

    Krink, Thiemo; Vesterstrøm, Jakob Svaneborg; Riget, Jacques

    2002-01-01

    In this paper, we introduce spatial extension to particles in the PSO model in order to overcome premature convergence in iterative optimisation. The standard PSO and the new model (SEPSO) are compared w.r.t. performance on well-studied benchmark problems. We show that the SEPSO indeed managed...

  14. Protection against natural radiation: Optimisation and decision exercises

    International Nuclear Information System (INIS)

    O'Riordan, M.C.

    1984-02-01

    Six easy exercises are presented in which cost-benefit analysis is used to optimise protection against natural radiation or to decide whether protection is appropriate. The exercises are illustrative only and do not commit the Board. (author)

  15. Modulation aware cluster size optimisation in wireless sensor networks

    Science.gov (United States)

    Sriram Naik, M.; Kumar, Vinay

    2017-07-01

    Wireless sensor networks (WSNs) play a great role because of their numerous advantages to the mankind. The main challenge with WSNs is the energy efficiency. In this paper, we have focused on the energy minimisation with the help of cluster size optimisation along with consideration of modulation effect when the nodes are not able to communicate using baseband communication technique. Cluster size optimisations is important technique to improve the performance of WSNs. It provides improvement in energy efficiency, network scalability, network lifetime and latency. We have proposed analytical expression for cluster size optimisation using traditional sensing model of nodes for square sensing field with consideration of modulation effects. Energy minimisation can be achieved by changing the modulation schemes such as BPSK, 16-QAM, QPSK, 64-QAM, etc., so we are considering the effect of different modulation techniques in the cluster formation. The nodes in the sensing fields are random and uniformly deployed. It is also observed that placement of base station at centre of scenario enables very less number of modulation schemes to work in energy efficient manner but when base station placed at the corner of the sensing field, it enable large number of modulation schemes to work in energy efficient manner.

  16. Optimisation of wire-cut EDM process parameter by Grey-based response surface methodology

    Science.gov (United States)

    Kumar, Amit; Soota, Tarun; Kumar, Jitendra

    2018-03-01

    Wire electric discharge machining (WEDM) is one of the advanced machining processes. Response surface methodology coupled with Grey relation analysis method has been proposed and used to optimise the machining parameters of WEDM. A face centred cubic design is used for conducting experiments on high speed steel (HSS) M2 grade workpiece material. The regression model of significant factors such as pulse-on time, pulse-off time, peak current, and wire feed is considered for optimising the responses variables material removal rate (MRR), surface roughness and Kerf width. The optimal condition of the machining parameter was obtained using the Grey relation grade. ANOVA is applied to determine significance of the input parameters for optimising the Grey relation grade.

  17. A constriction factor based particle swarm optimisation algorithm to solve the economic dispatch problem including losses

    Energy Technology Data Exchange (ETDEWEB)

    Young, Steven; Montakhab, Mohammad; Nouri, Hassan

    2011-07-15

    Economic dispatch (ED) is one of the most important problems to be solved in power generation as fractional percentage fuel reductions represent significant cost savings. ED wishes to optimise the power generated by each generating unit in a system in order to find the minimum operating cost at a required load demand, whilst ensuring both equality and inequality constraints are met. For the process of optimisation, a model must be created for each generating unit. The particle swarm optimisation technique is an evolutionary computation technique with one of the most powerful methods for solving global optimisation problems. The aim of this paper is to add in a constriction factor to the particle swarm optimisation algorithm (CFBPSO). Results show that the algorithm is very good at solving the ED problem and that CFBPSO must be able to work in a practical environment and so a valve point effect with transmission losses should be included in future work.

  18. Navigating catastrophes: Local but not global optimisation allows for macro-economic navigation of crises

    Science.gov (United States)

    Harré, Michael S.

    2013-02-01

    Two aspects of modern economic theory have dominated the recent discussion on the state of the global economy: Crashes in financial markets and whether or not traditional notions of economic equilibrium have any validity. We have all seen the consequences of market crashes: plummeting share prices, businesses collapsing and considerable uncertainty throughout the global economy. This seems contrary to what might be expected of a system in equilibrium where growth dominates the relatively minor fluctuations in prices. Recent work from within economics as well as by physicists, psychologists and computational scientists has significantly improved our understanding of the more complex aspects of these systems. With this interdisciplinary approach in mind, a behavioural economics model of local optimisation is introduced and three general properties are proven. The first is that under very specific conditions local optimisation leads to a conventional macro-economic notion of a global equilibrium. The second is that if both global optimisation and economic growth are required then under very mild assumptions market catastrophes are an unavoidable consequence. Third, if only local optimisation and economic growth are required then there is sufficient parametric freedom for macro-economic policy makers to steer an economy around catastrophes without overtly disrupting local optimisation.

  19. Optimising culture medium for producing the yeast Pichia onychis (Lv027

    Directory of Open Access Journals (Sweden)

    Andrés Díaz

    2005-01-01

    Full Text Available Optimising Pichia onychis yeast biomass production was evaluated using different substrates and different physicochemical conditions for liquid fermentation. The Plackett-Burman statistical design was initially applied for screening the most important nutritional variables (three carbon sources and eight nitrogen sources affecting yeast biomass production. Four nutritional sources and two physicochemical variables were subsequently evaluated using a factorial fractionated design as the starting point for optimising the process by applying a central composite rotational design. The results obtained f rom employing a polynomial regression model using the experimental data showed that biomass production was strongly affected by nutritional and physicochemical conditions. The highest yield was obtained in the following conditions: 43,42 g/L carbon source, 0,261 g/L nitrogen organic source, shaking at 110 rpm, 6,0 pH, 48 h total fermentation time during which 8,95 XlO9 cells/mL were obtained, equivalent to 6,30 g/L dry biomass. Key words: Pichia onychis, optimisation, liquid fermentation.

  20. Design of passive coolers for light-emitting diode lamps using topology optimisation

    DEFF Research Database (Denmark)

    Alexandersen, Joe; Sigmund, Ole; Meyer, Knud Erik

    2018-01-01

    Topology optimised designs for passive cooling of light-emitting diode (LED) lamps are investigated through extensive numerical parameter studies. The designs are optimised for either horizontal or vertical orientations and are compared to a lattice-fin design as well as a simple parameter......, while maintaining low sensitivity to orientation. Furthermore, they exhibit several defining features and provide insight and general guidelines for the design of passive coolers for LED lamps....

  1. Statistical optimisation techniques in fatigue signal editing problem

    International Nuclear Information System (INIS)

    Nopiah, Z. M.; Osman, M. H.; Baharin, N.; Abdullah, S.

    2015-01-01

    Success in fatigue signal editing is determined by the level of length reduction without compromising statistical constraints. A great reduction rate can be achieved by removing small amplitude cycles from the recorded signal. The long recorded signal sometimes renders the cycle-to-cycle editing process daunting. This has encouraged researchers to focus on the segment-based approach. This paper discusses joint application of the Running Damage Extraction (RDE) technique and single constrained Genetic Algorithm (GA) in fatigue signal editing optimisation.. In the first section, the RDE technique is used to restructure and summarise the fatigue strain. This technique combines the overlapping window and fatigue strain-life models. It is designed to identify and isolate the fatigue events that exist in the variable amplitude strain data into different segments whereby the retention of statistical parameters and the vibration energy are considered. In the second section, the fatigue data editing problem is formulated as a constrained single optimisation problem that can be solved using GA method. The GA produces the shortest edited fatigue signal by selecting appropriate segments from a pool of labelling segments. Challenges arise due to constraints on the segment selection by deviation level over three signal properties, namely cumulative fatigue damage, root mean square and kurtosis values. Experimental results over several case studies show that the idea of solving fatigue signal editing within a framework of optimisation is effective and automatic, and that the GA is robust for constrained segment selection

  2. Module detection in complex networks using integer optimisation

    Directory of Open Access Journals (Sweden)

    Tsoka Sophia

    2010-11-01

    Full Text Available Abstract Background The detection of modules or community structure is widely used to reveal the underlying properties of complex networks in biology, as well as physical and social sciences. Since the adoption of modularity as a measure of network topological properties, several methodologies for the discovery of community structure based on modularity maximisation have been developed. However, satisfactory partitions of large graphs with modest computational resources are particularly challenging due to the NP-hard nature of the related optimisation problem. Furthermore, it has been suggested that optimising the modularity metric can reach a resolution limit whereby the algorithm fails to detect smaller communities than a specific size in large networks. Results We present a novel solution approach to identify community structure in large complex networks and address resolution limitations in module detection. The proposed algorithm employs modularity to express network community structure and it is based on mixed integer optimisation models. The solution procedure is extended through an iterative procedure to diminish effects that tend to agglomerate smaller modules (resolution limitations. Conclusions A comprehensive comparative analysis of methodologies for module detection based on modularity maximisation shows that our approach outperforms previously reported methods. Furthermore, in contrast to previous reports, we propose a strategy to handle resolution limitations in modularity maximisation. Overall, we illustrate ways to improve existing methodologies for community structure identification so as to increase its efficiency and applicability.

  3. Statistical optimisation techniques in fatigue signal editing problem

    Energy Technology Data Exchange (ETDEWEB)

    Nopiah, Z. M.; Osman, M. H. [Fundamental Engineering Studies Unit Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 UKM (Malaysia); Baharin, N.; Abdullah, S. [Department of Mechanical and Materials Engineering Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 UKM (Malaysia)

    2015-02-03

    Success in fatigue signal editing is determined by the level of length reduction without compromising statistical constraints. A great reduction rate can be achieved by removing small amplitude cycles from the recorded signal. The long recorded signal sometimes renders the cycle-to-cycle editing process daunting. This has encouraged researchers to focus on the segment-based approach. This paper discusses joint application of the Running Damage Extraction (RDE) technique and single constrained Genetic Algorithm (GA) in fatigue signal editing optimisation.. In the first section, the RDE technique is used to restructure and summarise the fatigue strain. This technique combines the overlapping window and fatigue strain-life models. It is designed to identify and isolate the fatigue events that exist in the variable amplitude strain data into different segments whereby the retention of statistical parameters and the vibration energy are considered. In the second section, the fatigue data editing problem is formulated as a constrained single optimisation problem that can be solved using GA method. The GA produces the shortest edited fatigue signal by selecting appropriate segments from a pool of labelling segments. Challenges arise due to constraints on the segment selection by deviation level over three signal properties, namely cumulative fatigue damage, root mean square and kurtosis values. Experimental results over several case studies show that the idea of solving fatigue signal editing within a framework of optimisation is effective and automatic, and that the GA is robust for constrained segment selection.

  4. The current regulatory requirements on optimisation and BAT in Sweden in the context of geological disposal

    International Nuclear Information System (INIS)

    Dverstorp, B.

    2010-01-01

    Bjorn Dverstorp, Swedish Radiation Safety authority (SSM) presented 'The current regulatory requirements on optimisation and BAT in Sweden in the context of geological disposal'. In Sweden, a nuclear waste repository will be evaluated according to both to general environmental legislation (the Environmental Code, SFS, 1998:808) and according to more specific requirements in the Act on Nuclear Activities (SFS, 1984:3) and the Radiation Protection Act (SFS, 1988:220). The evaluations according to these laws will be carried out according to two separate, but coordinated, legal-review and decision-making processes. This will be a basis for the siting process. Although the requirements on BAT and siting in the Environmental Code apply to radiological protection, they aim at a broader system optimisation. The more specific requirements on optimisation and BAT of radiological protection of geological disposal systems are given in the regulations associated with the Radiation Protection Act. The Swedish radiation protection regulations (SSM, 2009) comprise three corner stones: a risk target, environmental protection goals and the use of optimisation and BAT. In SSM' s guidance optimisation is defined as a means to reduce risk, guided by the results of risk calculations. In case of a conflict between BAT and optimisation, measures satisfying BAT should have priority. Application of optimisation and BAT on different timescales are described as well as for human intrusion scenarios. B. Dverstorp explained that because of uncertainties in the long term there is a need for additional arguments in the safety case in support of decision making. It is in this context that the requirements on optimisation and BAT should be seen as supplementary to the risk target, in providing evidence that the developer has taken into consideration, as far as reasonably possible, measures and options for reducing future doses and risks. Both principles focus on the proponent's work on developing

  5. Optimised Design and Analysis of All-Optical Networks

    DEFF Research Database (Denmark)

    Glenstrup, Arne John

    2002-01-01

    through various experiments and is shown to produce good results and to be able to scale up to networks of realistic sizes. A novel method, subpath wavelength grouping, for routing connections in a multigranular all-optical network where several wavelengths can be grouped and switched at band and fibre......This PhD thesis presents a suite of methods for optimising design and for analysing blocking probabilities of all-optical networks. It thus contributes methodical knowledge to the field of computer assisted planning of optical networks. A two-stage greenfield optical network design optimiser...... is developed, based on shortest-path algorithms and a comparatively new metaheuristic called simulated allocation. It is able to handle design of all-optical mesh networks with optical cross-connects, considers duct as well as fibre and node costs, and can also design protected networks. The method is assessed...

  6. FISHRENT; Bio-economic simulation and optimisation model

    NARCIS (Netherlands)

    Salz, P.; Buisman, F.C.; Soma, K.; Frost, H.; Accadia, P.; Prellezo, R.

    2011-01-01

    Key findings: The FISHRENT model is a major step forward in bio-economic model-ling, combining features that have not been fully integrated in earlier models: 1- Incorporation of any number of species (or stock) and/or fleets 2- Integration of simulation and optimisation over a period of 25 years 3-

  7. Design of Circularly-Polarised, Crossed Drooping Dipole, Phased Array Antenna Using Genetic Algorithm Optimisation

    DEFF Research Database (Denmark)

    Larsen, Niels Vesterdal

    2007-01-01

    A printed drooping dipole array is designed and constructed. The design is based on a genetic algorithm optimisation procedure used in conjunction with the software programme AWAS. By optimising the array G/T for specific combinations of scan angles and frequencies an optimum design is obtained...

  8. Optimisation-based worst-case analysis and anti-windup synthesis for uncertain nonlinear systems

    Science.gov (United States)

    Menon, Prathyush Purushothama

    This thesis describes the development and application of optimisation-based methods for worst-case analysis and anti-windup synthesis for uncertain nonlinear systems. The worst-case analysis methods developed in the thesis are applied to the problem of nonlinear flight control law clearance for highly augmented aircraft. Local, global and hybrid optimisation algorithms are employed to evaluate worst-case violations of a nonlinear response clearance criterion, for a highly realistic aircraft simulation model and flight control law. The reliability and computational overheads associated with different opti misation algorithms are compared, and the capability of optimisation-based approaches to clear flight control laws over continuous regions of the flight envelope is demonstrated. An optimisation-based method for computing worst-case pilot inputs is also developed, and compared with current industrial approaches for this problem. The importance of explicitly considering uncertainty in aircraft parameters when computing worst-case pilot demands is clearly demonstrated. Preliminary results on extending the proposed framework to the problems of limit-cycle analysis and robustness analysis in the pres ence of time-varying uncertainties are also included. A new method for the design of anti-windup compensators for nonlinear constrained systems controlled using nonlinear dynamics inversion control schemes is presented and successfully applied to some simple examples. An algorithm based on the use of global optimisation is proposed to design the anti-windup compensator. Some conclusions are drawn from the results of the research presented in the thesis, and directions for future work are identified.

  9. Optimisation of imaging technique used in direct digital radiography

    International Nuclear Information System (INIS)

    Roberts, J A; Evans, S C; Rees, M

    2006-01-01

    The purpose of the study was to optimise the technique employed for AP shoulder and lateral cervical spine examinations following an investigation into image quality, based on clinical assessment, and effective dose, calculated from patient entrance surface dose measurements. A study was therefore conducted in an attempt to determine whether the increased radiation dose to the patient following the introduction of an anti-scatter grid was justified by the level of improvement in image quality. The study, involving 100 patients, was able to demonstrate that the increase in radiation dose to the patient when using an anti-scatter grid for AP shoulder examinations is not justified by the improved image quality. A poor level of inter-rater reliability between the consultants scoring the lateral cervical spine images prevented a firm conclusion from being reached. The fact that all images were of diagnostic quality, however, suggested that the use of the anti-scatter grid was unnecessary. Following completion of the project the hospital involved was informed of all findings

  10. DYNAMIC PLANNING INDICATORS FOR OPTIMISING THE ENERGY MODERNISATION OF RESIDENTIAL HOUSING STOCK

    Directory of Open Access Journals (Sweden)

    S. K. Bayramukov

    2016-01-01

    Full Text Available Objectives. In the article, the problem of the optimisation of the energy modernisation of residential housing is examined. Methods. A mathematical model for the optimisation of energy use is developed with the use of dynamic programming techniques. Results. The proposed method of assessing the effectiveness of comprehensive energy-saving measures can improve the quality of decision-making on housing recovery and increase its energy modernisation. The application of mathematical modeling allows for the distribution of funds to projects so that the implementation of organisational and technological solutions consistently implement measures that will lead to optimal social and economic effects. The developed mathematical model also allows the amount of quality housing to be maximised through the implementation of energy-saving and other measures when upgrading the housing stock. Problems concerning the renovation of housing stock are analysed. The concept of housing energy modernisation is introduced. The principal energysaving technologies in housing modernisation are distinguished. A schema for the optimal allocation of funds for energy-saving measures is described. It is assumed that the optimal solution is obtained independently of the number of steps and the initial supply of invested capital.Conclusion. The energy modernisation of the housing stock leads to a reduction in the expenditures of citizens on housing and utilities services, contributing to an increase in the integral index of comfort. A generalised method for optimal control of the housing stock is implemented on the basis of the provided schema for dynamic scheduling of the optimal distribution of funds for energy-saving measures. 

  11. Sizing Combined Heat and Power Units and Domestic Building Energy Cost Optimisation

    Directory of Open Access Journals (Sweden)

    Dongmin Yu

    2017-06-01

    Full Text Available Many combined heat and power (CHP units have been installed in domestic buildings to increase energy efficiency and reduce energy costs. However, inappropriate sizing of a CHP may actually increase energy costs and reduce energy efficiency. Moreover, the high manufacturing cost of batteries makes batteries less affordable. Therefore, this paper will attempt to size the capacity of CHP and optimise daily energy costs for a domestic building with only CHP installed. In this paper, electricity and heat loads are firstly used as sizing criteria in finding the best capacities of different types of CHP with the help of the maximum rectangle (MR method. Subsequently, the genetic algorithm (GA will be used to optimise the daily energy costs of the different cases. Then, heat and electricity loads are jointly considered for sizing different types of CHP and for optimising the daily energy costs through the GA method. The optimisation results show that the GA sizing method gives a higher average daily energy cost saving, which is 13% reduction compared to a building without installing CHP. However, to achieve this, there will be about 3% energy efficiency reduction and 7% input power to rated power ratio reduction compared to using the MR method and heat demand in sizing CHP.

  12. Intelligent Data Storage and Retrieval for Design Optimisation – an Overview

    Directory of Open Access Journals (Sweden)

    C. Peebles

    2005-01-01

    Full Text Available This paper documents the findings of a literature review conducted by the Sir Lawrence Wackett Centre for Aerospace Design Technology at RMIT University. The review investigates aspects of a proposed system for intelligent design optimisation. Such a system would be capable of efficiently storing (and compressing if required a range of types of design data into an intelligent database. This database would be accessed by the system during subsequent design processes, allowing for search of relevant design data for re-use in later designs, allowing it to become very efficient in reducing the time for later designs as the database grows in size. Extensive research has been performed, in both theoretical aspects of the project, and practical examples of current similar systems. This research covers the areas of database systems, database queries, representation and compression of design data, geometric representation and heuristic methods for design applications. 

  13. OCTAVIUS: a FP7 project demonstrating CO2 capture technologies

    NARCIS (Netherlands)

    Broutin, P.; Kvamsdal, H.M.; La Marca, C.; Os, P.J. van; Robinson, L.

    2014-01-01

    The OCTAVIUS project (Optimisation of CO2 Capture Technology Allowing Verification and Implementation at Utility Scale) has started on March 1st 2012 for a period of 5 years, as part of the 7th Framework Programme of the European Commission. Gathering 15 European and 2 South African partners,

  14. Formulation des betons autopla~ants : Optimisation du squelette ...

    African Journals Online (AJOL)

    Formulation des betons autopla~ants : Optimisation du squelette granulaire par la methode graphique de Dreux - Gorisse. Fatiha Boumaza - Zeraoulia* & Mourad Behim. Laboratoire Materiaux, Geo - Materiaux et Environnement - Departement de Genie Civil. Universite Badji Mokhtar Annaba - BP 12, 23000 Annaba - ...

  15. Genetic algorithms and artificial neural networks for loading pattern optimisation of advanced gas-cooled reactors

    Energy Technology Data Exchange (ETDEWEB)

    Ziver, A.K. E-mail: a.k.ziver@imperial.ac.uk; Pain, C.C; Carter, J.N.; Oliveira, C.R.E. de; Goddard, A.J.H.; Overton, R.S

    2004-03-01

    A non-generational genetic algorithm (GA) has been developed for fuel management optimisation of Advanced Gas-Cooled Reactors, which are operated by British Energy and produce around 20% of the UK's electricity requirements. An evolutionary search is coded using the genetic operators; namely selection by tournament, two-point crossover, mutation and random assessment of population for multi-cycle loading pattern (LP) optimisation. A detailed description of the chromosomes in the genetic algorithm coded is presented. Artificial Neural Networks (ANNs) have been constructed and trained to accelerate the GA-based search during the optimisation process. The whole package, called GAOPT, is linked to the reactor analysis code PANTHER, which performs fresh fuel loading, burn-up and power shaping calculations for each reactor cycle by imposing station-specific safety and operational constraints. GAOPT has been verified by performing a number of tests, which are applied to the Hinkley Point B and Hartlepool reactors. The test results giving loading pattern (LP) scenarios obtained from single and multi-cycle optimisation calculations applied to realistic reactor states of the Hartlepool and Hinkley Point B reactors are discussed. The results have shown that the GA/ANN algorithms developed can help the fuel engineer to optimise loading patterns in an efficient and more profitable way than currently available for multi-cycle refuelling of AGRs. Research leading to parallel GAs applied to LP optimisation are outlined, which can be adapted to present day LWR fuel management problems.

  16. Manufacturing footprint optimisation: a necessity for manufacturing network in changing business environment

    DEFF Research Database (Denmark)

    Yang, Cheng; Farooq, Sami; Johansen, John

    2010-01-01

    Facing the unpredictable financial crisis, optimising the footprint can be the biggest and most important transformation a manufacturer can undertake. In order to realise the optimisation, fundamental understanding on manufacturing footprint is required. Different elements of manufacturing...... footprint have been investigated independently in the existing literature. In this paper, for the purpose of relationship exploration between different elements, manufacturing footprints of three industrial companies are traced historically. Based on them, four reasons for the transformation...

  17. Stochastic Optimisation of Battery System Operation Strategy under different Utility Tariff Structures

    OpenAIRE

    Erdal, Jørgen Sørgård

    2017-01-01

    This master thesis develops a stochastic optimisation software for household grid-connected batteries combined with PV-systems. The objective of the optimisation is to operate the battery system in order to minimise the costs of the consumer, and it was implemented in MATLAB using a self-written stochastic dynamic programming algorithm. Load was considered as a stochastic variable and modelled as a Markov Chain. Transition probabilities between time steps were calculated using historic load p...

  18. Economic and Mathematical Modelling of Optimisation of Transaction Expenses of Engineering Enterprises

    OpenAIRE

    Makaliuk Iryna V.

    2014-01-01

    The article identifies stages of the process of optimisation of transaction expenses. It develops an economic and mathematical model of optimisation of transaction expenses of engineering enterprises by the criterion of maximisation of income from realisation of products and system of restrictions, which envisages exceeding income growth rate over the expenses growth rate. The article offers to use types of expenses by accounting accounts as indicators of transaction expenses. In the result o...

  19. Research on Duct Flow Field Optimisation of a Robot Vacuum Cleaner

    Directory of Open Access Journals (Sweden)

    Xiao-bo Lai

    2011-11-01

    Full Text Available The duct of a robot vacuum cleaner is the length of the flow channel between the inlet of the rolling brush blower and the outlet of the vacuum blower. To cope with the pressure drop problem of the duct flow field in a robot vacuum cleaner, a method based on Pressure Implicit with Splitting of Operators (PRISO algorithm is introduced and the optimisation design of the duct flow field is implemented. Firstly, the duct structure in a robot vacuum cleaner is taken as a research object, with the computational fluid dynamics (CFD theories adopted; a three-dimensional fluid model of the duct is established by means of the FLUENT solver of the CFD software. Secondly, with the k-∊ turbulence model of three-dimensional incompressible fluid considered and the PRISO pressure modification algorithm employed, the flow field numerical simulations inside the duct of the robot vacuum cleaner are carried out. Then, the velocity vector plots on the arbitrary plane of the duct flow field are obtained. Finally, an investigation of the dynamic characteristics of the duct flow field is done and defects of the original duct flow field are analysed, the optimisation of the original flow field has then been conducted. Experimental results show that the duct flow field after optimisation can effectively reduce pressure drop, the feasibility as well as the correctness of the theoretical modelling and optimisation approaches are validated.

  20. Research on Duct Flow Field Optimisation of a Robot Vacuum Cleaner

    Directory of Open Access Journals (Sweden)

    Xiao-bo Lai

    2011-11-01

    Full Text Available The duct of a robot vacuum cleaner is the length of the flow channel between the inlet of the rolling brush blower and the outlet of the vacuum blower. To cope with the pressure drop problem of the duct flow field in a robot vacuum cleaner, a method based on Pressure Implicit with Splitting of Operators (PRISO algorithm is introduced and the optimisation design of the duct flow field is implemented. Firstly, the duct structure in a robot vacuum cleaner is taken as a research object, with the computational fluid dynamics (CFD theories adopted; a three‐dimensional fluid model of the duct is established by means of the FLUENT solver of the CFD software. Secondly, with the k‐ε turbulence model of three‐ dimensional incompressible fluid considered and the PRISO pressure modification algorithm employed, the flow field numerical simulations inside the duct of the robot vacuum cleaner are carried out. Then, the velocity vector plots on the arbitrary plane of the duct flow field are obtained. Finally, an investigation of the dynamic characteristics of the duct flow field is done and defects of the original duct flow field are analysed, the optimisation of the original flow field has then been conducted. Experimental results show that the duct flow field after optimisation can effectively reduce pressure drop, the feasibility as well as the correctness of the theoretical modelling and optimisation approaches are validated.

  1. Multigrid Implementation of Cellular Automata for Topology Optimisation of Continuum Structures with Design Dependent loads

    NARCIS (Netherlands)

    Zakhama, R.

    2009-01-01

    Topology optimisation of continuum structures has become mature enough to be often applied in industry and continues to attract the attention of researchers and software companies in various engineering fields. Traditionally, most available algorithms for solving topology optimisation problems are

  2. The optimisation study of tbp synthesis process by phosphoric acid

    International Nuclear Information System (INIS)

    Amedjkouh, A.; Attou, M.; Azzouz, A.; Zaoui, B.

    1995-07-01

    The present work deals with the optimisation study of TBP synthesis process by phosphoric acid. This way of synthesis is more advantageous than POCL3 or P2O5 as phosphatant agents. these latters are toxic and dangerous for the environnement. The optimisation study is based on a series of 16 experiences taking into account the range of variation of the following parameters : temperature, pressure, reagents mole ratio, promoter content. the yield calculation is based on the randomisation of an equation including all parameters. the resolution of this equation gave a 30% TBP molar ratio. this value is in agreement with that of experimental data

  3. Flotation process control optimisation at Prominent Hill

    International Nuclear Information System (INIS)

    Lombardi, Josephine; Muhamad, Nur; Weidenbach, M.

    2012-01-01

    OZ Minerals' Prominent Hill copper- gold concentrator is located 130 km south east of the town of Coober Pedy in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 9.6 Mtpa ore throughput capacity. The flotation circuit includes six rougher cells, an IseMill for regrinding the rougher concentrate and a Jameson cell heading up the three stage conventional cell cleaner circuit. In total there are four level controllers in the rougher train and ten level controllers in the cleaning circuit for 18 cells. Generic proportional — integral and derivative (PID) control used on the level controllers alone propagated any disturbances downstream in the circuit that were generated from the grinding circuit, hoppers, between cells and interconnected banks of cells, having a negative impact on plant performance. To better control such disturbances, FloatStar level stabiliser was selected for installation on the flotation circuit to account for the interaction between the cells. Multivariable control was also installed on the five concentrate hoppers to maintain consistent feed to the cells and to the IsaMill. An additional area identified for optimisation in the flotation circuit was the mass pull rate from the rougher cells. FloatStar flow optimiser was selected to be installed subsequent to the FloatStar level stabiliser. This allowed for a unified, consistent and optimal approach to running the rougher circuit. This paper describes the improvement in the stabilisation of the circuit achieved by the FloatStar level stabiliser by using the interaction matrix between cell level controllers and the results and benefits of implementing the FloatStar flow optimiser on the rougher train.

  4. Optimisation of monochrome images

    International Nuclear Information System (INIS)

    Potter, R.

    1983-01-01

    Gamma cameras with modern imaging systems usually digitize the signals to allow storage and processing of the image in a computer. Although such computer systems are widely used for the extraction of quantitative uptake estimates and the analysis of time variant data, the vast majority of nuclear medicine images is still interpreted on the basis of an observer's visual assessment of a photographic hardcopy image. The optimisation of hardcopy devices is therefore vital and factors such as resolution, uniformity, noise grey scales and display matrices are discussed. Once optimum display parameters have been determined, routine procedures for quality control need to be established; suitable procedures are discussed. (U.K.)

  5. Use of artificial intelligence techniques for optimisation of co-combustion of coal with biomass

    Energy Technology Data Exchange (ETDEWEB)

    Tan, C.K.; Wilcox, S.J.; Ward, J. [University of Glamorgan, Pontypridd (United Kingdom). Division of Mechanical Engineering

    2006-03-15

    The optimisation of burner operation in conventional pulverised-coal-fired boilers for co-combustion applications represents a significant challenge This paper describes a strategic framework in which Artificial Intelligence (AI) techniques can be applied to solve such an optimisation problem. The effectiveness of the proposed system is demonstrated by a case study that simulates the co-combustion of coal with sewage sludge in a 500-kW pilot-scale combustion rig equipped with a swirl stabilised low-NOx burner. A series of Computational Fluid Dynamics (CFD) simulations were performed to generate data for different operating conditions, which were then used to train several Artificial Neural Networks (ANNs) to predict the co-combustion performance. Once trained, the ANNs were able to make estimations of unseen situations in a fraction of the time taken by the CFD simulation. Consequently, the networks were capable of representing the underlying physics of the CFD models and could be executed efficiently for a large number of iterations as required by optimisation techniques based on Evolutionary Algorithms (EAs). Four operating parameters of the burner, namely the swirl angles and flow rates of the secondary and tertiary combustion air were optimised with the objective of minimising the NOx and CO emissions as well as the unburned carbon at the furnace exit. The results suggest that ANNs combined with EAs provide a useful tool for optimising co-combustion processes.

  6. Optimisation of active suspension control inputs for improved performance of active safety systems

    Science.gov (United States)

    Čorić, Mirko; Deur, Joško; Xu, Li; Tseng, H. Eric; Hrovat, Davor

    2018-01-01

    A collocation-type control variable optimisation method is used to investigate the extent to which the fully active suspension (FAS) can be applied to improve the vehicle electronic stability control (ESC) performance and reduce the braking distance. First, the optimisation approach is applied to the scenario of vehicle stabilisation during the sine-with-dwell manoeuvre. The results are used to provide insights into different FAS control mechanisms for vehicle performance improvements related to responsiveness and yaw rate error reduction indices. The FAS control performance is compared to performances of the standard ESC system, optimal active brake system and combined FAS and ESC configuration. Second, the optimisation approach is employed to the task of FAS-based braking distance reduction for straight-line vehicle motion. Here, the scenarios of uniform and longitudinally or laterally non-uniform tyre-road friction coefficient are considered. The influences of limited anti-lock braking system (ABS) actuator bandwidth and limit-cycle ABS behaviour are also analysed. The optimisation results indicate that the FAS can provide competitive stabilisation performance and improved agility when compared to the ESC system, and that it can reduce the braking distance by up to 5% for distinctively non-uniform friction conditions.

  7. The Energy-Efficient Quarry: Towards improved understanding and optimisation of energy use and minimisation of CO2 generation in the aggregates industry.

    Science.gov (United States)

    Hill, Ian; White, Toby; Owen, Sarah

    2014-05-01

    Extraction and processing of rock materials to produce aggregates is carried out at some 20,000 quarries across the EU. All stages of the processing and transport of hard and dense materials inevitably consume high levels of energy and have consequent significant carbon footprints. The FP7 project "the Energy Efficient Quarry" (EE-Quarry) has been addressing this problem and has devised strategies, supported by modelling software, to assist the quarrying industry to assess and optimise its energy use, and to minimise its carbon footprint. Aggregate quarries across Europe vary enormously in the scale of the quarrying operations, the nature of the worked mineral, and the processing to produce a final market product. Nevertheless most quarries involve most or all of a series of essential stages; deposit assessment, drilling and blasting, loading and hauling, and crushing and screening. The process of determining the energy-efficiency of each stage is complex, but is broadly understood in principle and there are numerous sources of information and guidance available in the literature and on-line. More complex still is the interaction between each of these stages. For example, using a little more energy in blasting to increase fragmentation may save much greater energy in later crushing and screening, but also generate more fines material which is discarded as waste and the embedded energy in this material is lost. Thus the calculation of the embedded energy in the waste material becomes an input to the determination of the blasting strategy. Such feedback loops abound in the overall quarry optimisation. The project has involved research and demonstration operations at a number of quarries distributed across Europe carried out by all partners in the EE-Quarry project, working in collaboration with many of the major quarrying companies operating in the EU. The EE-Quarry project is developing a sophisticated modelling tool, the "EE-Quarry Model" available to the quarrying

  8. A knowledge representation model for the optimisation of electricity generation mixes

    International Nuclear Information System (INIS)

    Chee Tahir, Aidid; Bañares-Alcántara, René

    2012-01-01

    Highlights: ► Prototype energy model which uses semantic representation (ontologies). ► Model accepts both quantitative and qualitative based energy policy goals. ► Uses logic inference to formulate equations for linear optimisation. ► Proposes electricity generation mix based on energy policy goals. -- Abstract: Energy models such as MARKAL, MESSAGE and DNE-21 are optimisation tools which aid in the formulation of energy policies. The strength of these models lie in their solid theoretical foundations built on rigorous mathematical equations designed to process numerical (quantitative) data related to economics and the environment. Nevertheless, a complete consideration of energy policy issues also requires the consideration of the political and social aspects of energy. These political and social issues are often associated with non-numerical (qualitative) information. To enable the evaluation of these aspects in a computer model, we hypothesise that a different approach to energy model optimisation design is required. A prototype energy model that is based on a semantic representation using ontologies and is integrated to engineering models implemented in Java has been developed. The model provides both quantitative and qualitative evaluation capabilities through the use of logical inference. The semantic representation of energy policy goals is used (i) to translate a set of energy policy goals into a set of logic queries which is then used to determine the preferred electricity generation mix and (ii) to assist in the formulation of a set of equations which is then solved in order to obtain a proposed electricity generation mix. Scenario case studies have been developed and tested on the prototype energy model to determine its capabilities. Knowledge queries were made on the semantic representation to determine an electricity generation mix which fulfilled a set of energy policy goals (e.g. CO 2 emissions reduction, water conservation, energy supply

  9. The PALOS project and its significance for industrial application

    Energy Technology Data Exchange (ETDEWEB)

    Guzzella, L. [Swiss Federal Institute of Technology Zuerich (ETHZ), Institute for Measurement and Control Laboratory (IMRT), Zuerich (Switzerland); Spring, P. [Swiss Federal Institut of Technology Zuerich (ETHZ), Institut fuer Mess- und Regeltechnik, Zuerich (Switzerland)

    2001-07-01

    This report compiled by the Swiss Federal Institute of Technology ETH introduces the PALOS (PArt Load Optimised System) concept for a downsized supercharged engine. The authors note that a mid-class passenger car needs an average power at the wheel of only 4.5 kW for typical driving cycles. For acceleration from 0 to 100 km/h within 10 seconds, however, the same vehicle requires a wheel power of approximately 120 kW. Thus, the engine efficiency is low under part load driving conditions. The objectives of the PALOS project are discussed as are methods to increase engine systems efficiency. Close collaboration with industrial partners during the whole project that lead to a high level of know-how transfer from university to industry and vice versa is noted. Four PhD theses on the subject are summarised: Part-load optimised engine systems, engine thermo-management for fuel consumption reduction, optimal operation of CVT-based powertrains and mean value modelling of a pressure wave supercharger (PWS), including exhaust gas recirculation, is looked at.

  10. Biomass supply chain optimisation for Organosolv-based biorefineries.

    Science.gov (United States)

    Giarola, Sara; Patel, Mayank; Shah, Nilay

    2014-05-01

    This work aims at providing a Mixed Integer Linear Programming modelling framework to help define planning strategies for the development of sustainable biorefineries. The up-scaling of an Organosolv biorefinery was addressed via optimisation of the whole system economics. Three real world case studies were addressed to show the high-level flexibility and wide applicability of the tool to model different biomass typologies (i.e. forest fellings, cereal residues and energy crops) and supply strategies. Model outcomes have revealed how supply chain optimisation techniques could help shed light on the development of sustainable biorefineries. Feedstock quality, quantity, temporal and geographical availability are crucial to determine biorefinery location and the cost-efficient way to supply the feedstock to the plant. Storage costs are relevant for biorefineries based on cereal stubble, while wood supply chains present dominant pretreatment operations costs. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Utility systems operation: Optimisation-based decision making

    International Nuclear Information System (INIS)

    Velasco-Garcia, Patricia; Varbanov, Petar Sabev; Arellano-Garcia, Harvey; Wozny, Guenter

    2011-01-01

    Utility systems provide heat and power to industrial sites. The importance of operating these systems in an optimal way has increased significantly due to the unstable and in the long term rising prices of fossil fuels as well as the need for reducing the greenhouse gas emissions. This paper presents an analysis of the problem for supporting operator decision making under conditions of variable steam demands from the production processes on an industrial site. An optimisation model has been developed, where besides for running the utility system, also the costs associated with starting-up the operating units have been modelled. The illustrative case study shows that accounting for the shut-downs and start-ups of utility operating units can bring significant cost savings. - Highlights: → Optimisation methodology for decision making on running utility systems. → Accounting for varying steam demands. → Optimal operating specifications when a demand change occurs. → Operating costs include start-up costs of boilers and other units. → Validated on a real-life case study. Up to 20% cost savings are possible.

  12. Production optimisation in the petrochemical industry by hierarchical multivariate modelling. Phase 2: On-line implementation

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, Aasa; Persson, Fredrik; Andersson, Magnus

    2009-07-15

    IVL, together with Emerson Process Management, has developed a decision support system (DSS) based on multivariate statistical process models. The system was implemented at Nynas AB's refinery in order to provide real-time TBP curves and to enable the operator to optimise the process with regards to product quality and energy consumption. The project resulted in the following proven benefits at the industrial reference site, Nynas Refinery in Gothenburg: - Increased yield with up to 14 % (relative terms) for the most valuable product - Decreased energy consumption of 8 %. Validation of model predictions compared to the laboratory analysis showed that the prediction error lay within 1 deg C throughout the whole test period

  13. Optimisation of the performance of a novel rotationally asymmetrical optical concentrator design for building integrated photovoltaic system

    International Nuclear Information System (INIS)

    Abu-Bakar, Siti Hawa; Muhammad-Sukki, Firdaus; Freier, Daria; Ramirez-Iniguez, Roberto; Mallick, Tapas Kumar; Munir, Abu Bakar; Mohd Yasin, Siti Hajar; Abubakar Mas'ud, Abdullahi; Md Yunus, Norhidayah

    2015-01-01

    Solar energy is one of the renewable energy sources that has shown promising potential in addressing the world's energy needs, particularly via the solar PV (photovoltaic) technology. However, the high cost of installation is still being considered as the main obstacle to the widespread adoption of solar PV system. The use of solar concentrators is one of the solutions that could help to produce lower cost solar PV systems. One of the existing concentrator designs is known as the RADTIRC (rotationally asymmetrical dielectric totally internally reflecting concentrator) which was developed in GCU (Glasgow Caledonian University) since 2010. This paper aims at optimising the existing RADTIRC prototype by increasing its electrical output whilst keeping the cost of the system at minimum. This is achieved by adopting a better material and a different technique to fabricate the concentrator. The optimised RADTIRC prototype was fabricated from PMMA (polymethyl-methacrylate) using injection moulding. It was found that the optimised RADTIRC-PV prototype generated an opto-electronic gain of 4.48 when compared with the bare cell under STC (standard test conditions). A comparison with the old prototype showed that the optimised RADTIRC-PV prototype increased the short circuit current by 13.57% under STC. - Highlights: • An optimisation of the performance of the RADTIRC was presented. • The optimised prototype was fabricated from PMMA using injection moulding. • The electrical and optical performances were investigated. • The optimised prototype generated an opto-electronic gain of 4.48x

  14. Improving linear transport infrastructure efficiency by automated learning and optimised predictive maintenance techniques (INFRALERT)

    Science.gov (United States)

    Jiménez-Redondo, Noemi; Calle-Cordón, Alvaro; Kandler, Ute; Simroth, Axel; Morales, Francisco J.; Reyes, Antonio; Odelius, Johan; Thaduri, Aditya; Morgado, Joao; Duarte, Emmanuele

    2017-09-01

    The on-going H2020 project INFRALERT aims to increase rail and road infrastructure capacity in the current framework of increased transportation demand by developing and deploying solutions to optimise maintenance interventions planning. It includes two real pilots for road and railways infrastructure. INFRALERT develops an ICT platform (the expert-based Infrastructure Management System, eIMS) which follows a modular approach including several expert-based toolkits. This paper presents the methodologies and preliminary results of the toolkits for i) nowcasting and forecasting of asset condition, ii) alert generation, iii) RAMS & LCC analysis and iv) decision support. The results of these toolkits in a meshed road network in Portugal under the jurisdiction of Infraestruturas de Portugal (IP) are presented showing the capabilities of the approaches.

  15. Analysis of optimisation method for a two-stroke piston ring using the Finite Element Method and the Simulated Annealing Method

    Science.gov (United States)

    Kaliszewski, M.; Mazuro, P.

    2016-09-01

    Simulated Annealing Method of optimisation for the sealing piston ring geometry is tested. The aim of optimisation is to develop ring geometry which would exert demanded pressure on a cylinder just while being bended to fit the cylinder. Method of FEM analysis of an arbitrary piston ring geometry is applied in an ANSYS software. The demanded pressure function (basing on formulae presented by A. Iskra) as well as objective function are introduced. Geometry definition constructed by polynomials in radial coordinate system is delivered and discussed. Possible application of Simulated Annealing Method in a piston ring optimisation task is proposed and visualised. Difficulties leading to possible lack of convergence of optimisation are presented. An example of an unsuccessful optimisation performed in APDL is discussed. Possible line of further optimisation improvement is proposed.

  16. Validation of a large-scale audit technique for CT dose optimisation

    International Nuclear Information System (INIS)

    Wood, T. J.; Davis, A. W.; Moore, C. S.; Beavis, A. W.; Saunderson, J. R.

    2008-01-01

    The expansion and increasing availability of computed tomography (CT) imaging means that there is a greater need for the development of efficient optimisation strategies that are able to inform clinical practice, without placing a significant burden on limited departmental resources. One of the most fundamental aspects to any optimisation programme is the collection of patient dose information, which can be compared with appropriate diagnostic reference levels. This study has investigated the implementation of a large-scale audit technique, which utilises data that already exist in the radiology information system, to determine typical doses for a range of examinations on four CT scanners. This method has been validated against what is considered the 'gold standard' technique for patient dose audits, and it has been demonstrated that results equivalent to the 'standard-sized patient' can be inferred from this much larger data set. This is particularly valuable where CT optimisation is concerned as it is considered a 'high dose' technique, and hence close monitoring of patient dose is particularly important. (authors)

  17. Optimisation of the alcoholic fermentation of aqueous jerivá pulp extract

    Directory of Open Access Journals (Sweden)

    Guilherme Arielo Rodrigues Maia

    2014-05-01

    Full Text Available The objective of this research is to determinate the optimum conditions for the alcoholic fermentation process of aqueous jerivá pulp extract using the response surface methodology and simplex optimisation technique. The incomplete factorial design 3³ was applied with the yeast extract, NH4H2PO4 and yeast as the independent variables and the alcohol production yield as the response. The regression analysis indicated that the model is predictive, and the simplex optimisation generated a formulation containing 0.35 g L-1 yeast extract, 6.33 g L-1 yeast and 0.30 g L-1NH4H2PO4 for an optimum yield of 85.40% ethanol. To validate the predictive equation, the experiment was carried out in triplicate under optimum conditions, and an average yield of 87.15% was obtained. According to a t-test, no significant difference was observed (on the order of 5% between the average value obtained and the value indicated by the simplex optimisation technique.

  18. Optimisation de modèles de propagation à partir des données de ...

    African Journals Online (AJOL)

    optimisation radio dans les réseaux mobiles. Le présent article présente une étude comparative de cinq méthodes d'optimisation de modèles de propagation à savoir : La régression linéaire, la méthode de Newton de second ordre, le recuit ...

  19. Parallel unstructured mesh optimisation for 3D radiation transport and fluids modelling

    International Nuclear Information System (INIS)

    Gorman, G.J.; Pain, Ch. C.; Oliveira, C.R.E. de; Umpleby, A.P.; Goddard, A.J.H.

    2003-01-01

    In this paper we describe the theory and application of a parallel mesh optimisation procedure to obtain self-adapting finite element solutions on unstructured tetrahedral grids. The optimisation procedure adapts the tetrahedral mesh to the solution of a radiation transport or fluid flow problem without sacrificing the integrity of the boundary (geometry), or internal boundaries (regions) of the domain. The objective is to obtain a mesh which has both a uniform interpolation error in any direction and the element shapes are of good quality. This is accomplished with use of a non-Euclidean (anisotropic) metric which is related to the Hessian of the solution field. Appropriate scaling of the metric enables the resolution of multi-scale phenomena as encountered in transient incompressible fluids and multigroup transport calculations. The resulting metric is used to calculate element size and shape quality. The mesh optimisation method is based on a series of mesh connectivity and node position searches of the landscape defining mesh quality which is gauged by a functional. The mesh modification thus fits the solution field(s) in an optimal manner. The parallel mesh optimisation/adaptivity procedure presented in this paper is of general applicability. We illustrate this by applying it to a transient CFD (computational fluid dynamics) problem. Incompressible flow past a cylinder at moderate Reynolds numbers is modelled to demonstrate that the mesh can follow transient flow features. (authors)

  20. Structural-electrical coupling optimisation for radiating and scattering performances of active phased array antenna

    Science.gov (United States)

    Wang, Congsi; Wang, Yan; Wang, Zhihai; Wang, Meng; Yuan, Shuai; Wang, Weifeng

    2018-04-01

    It is well known that calculating and reducing of radar cross section (RCS) of the active phased array antenna (APAA) are both difficult and complicated. It remains unresolved to balance the performance of the radiating and scattering when the RCS is reduced. Therefore, this paper develops a structure and scattering array factor coupling model of APAA based on the phase errors of radiated elements generated by structural distortion and installation error of the array. To obtain the optimal radiating and scattering performance, an integrated optimisation model is built to optimise the installation height of all the radiated elements in normal direction of the array, in which the particle swarm optimisation method is adopted and the gain loss and scattering array factor are selected as the fitness function. The simulation indicates that the proposed coupling model and integrated optimisation method can effectively decrease the RCS and that the necessary radiating performance can be simultaneously guaranteed, which demonstrate an important application value in engineering design and structural evaluation of APAA.

  1. An effective approach to reducing strategy space for maintenance optimisation of multistate series–parallel systems

    International Nuclear Information System (INIS)

    Zhou, Yifan; Lin, Tian Ran; Sun, Yong; Bian, Yangqing; Ma, Lin

    2015-01-01

    Maintenance optimisation of series–parallel systems is a research topic of practical significance. Nevertheless, a cost-effective maintenance strategy is difficult to obtain due to the large strategy space for maintenance optimisation of such systems. The heuristic algorithm is often employed to deal with this problem. However, the solution obtained by the heuristic algorithm is not always the global optimum and the algorithm itself can be very time consuming. An alternative method based on linear programming is thus developed in this paper to overcome such difficulties by reducing strategy space of maintenance optimisation. A theoretical proof is provided in the paper to verify that the proposed method is at least as effective as the existing methods for strategy space reduction. Numerical examples for maintenance optimisation of series–parallel systems having multistate components and considering both economic dependence among components and multiple-level imperfect maintenance are also presented. The simulation results confirm that the proposed method is more effective than the existing methods in removing inappropriate maintenance strategies of multistate series–parallel systems. - Highlights: • A new method using linear programming is developed to reduce the strategy space. • The effectiveness of the new method for strategy reduction is theoretically proved. • Imperfect maintenance and economic dependence are considered during optimisation

  2. Optimisation of the LHCb detector

    CERN Document Server

    Hierck, R H

    2003-01-01

    This thesis describes a comparison of the LHCb classic and LHCb light concept from a tracking perspective. The comparison includes the detector occupancies, the various pattern recognition algorithms and the reconstruction performance. The final optimised LHCb setup is used to study the physics performance of LHCb for the Bs->DsK and Bs->DsPi decay channels. This includes both the event selection and a study of the sensitivity for the Bs oscillation frequency, delta m_s, the Bs lifetime difference, DGamma_s, and the CP parameter gamma-2delta gamma.

  3. EFIT fuel cycle analysis with the EQL3D procedure

    International Nuclear Information System (INIS)

    Krepel, Jiri; Mikityuk, Konstantin; Sarotto, Massimo; Artioli, Carlo

    2009-01-01

    Accelerator Driven Systems (ADS) represent one of the possible future strategies for Minor Actinides (MA) transmutation. EFIT - European Facility for Industrial Transmutation is a 400 MWth ADS designed in the future of EUROTRANS project. It is fuelled by MA and Pu embedded in the inert Mg matrix, cooled by lead (673-753 K), and driven by an accelerator, which provides 15 mA current of 800 MeV protons. The subcritical core is divided into three radial zones, which differ in pin diameter or inert matrix percentage. This design flattens the flux distribution and enables to maximize the power density. (author)

  4. OCTAVIUS: a new FP7 project demonstrating CO2 capture technologies

    NARCIS (Netherlands)

    Broutin, P.; Kvamsdal, H.M.; Marca, C. la; Os, P.J. van; Booth, N.

    2013-01-01

    The OCTAVIUS project (Optimisation of CO2 Capture Technology Allowing Verification and Implementation at Utility Scale) has started on March 1st 2012 for a period of 5 years, as part of the 7th Framework Programme of the European Commission. Gathering 15 European and 2 South African partners,

  5. Energy efficiency optimisation for distillation column using artificial neural network models

    International Nuclear Information System (INIS)

    Osuolale, Funmilayo N.; Zhang, Jie

    2016-01-01

    This paper presents a neural network based strategy for the modelling and optimisation of energy efficiency in distillation columns incorporating the second law of thermodynamics. Real-time optimisation of distillation columns based on mechanistic models is often infeasible due to the effort in model development and the large computation effort associated with mechanistic model computation. This issue can be addressed by using neural network models which can be quickly developed from process operation data. The computation time in neural network model evaluation is very short making them ideal for real-time optimisation. Bootstrap aggregated neural networks are used in this study for enhanced model accuracy and reliability. Aspen HYSYS is used for the simulation of the distillation systems. Neural network models for exergy efficiency and product compositions are developed from simulated process operation data and are used to maximise exergy efficiency while satisfying products qualities constraints. Applications to binary systems of methanol-water and benzene-toluene separations culminate in a reduction of utility consumption of 8.2% and 28.2% respectively. Application to multi-component separation columns also demonstrate the effectiveness of the proposed method with a 32.4% improvement in the exergy efficiency. - Highlights: • Neural networks can accurately model exergy efficiency in distillation columns. • Bootstrap aggregated neural network offers improved model prediction accuracy. • Improved exergy efficiency is obtained through model based optimisation. • Reductions of utility consumption by 8.2% and 28.2% were achieved for binary systems. • The exergy efficiency for multi-component distillation is increased by 32.4%.

  6. Risk Management Improvement of Engineering Projects in Woodworking Industry

    Directory of Open Access Journals (Sweden)

    Simona Bartkutė

    2014-02-01

    Full Text Available Risk is a complex phenomenon that has physical, monetary, cultural and social dimensions. Every company wants tosave money, time, increase quality, optimise manufacturing, but each factor may involve different risks with different influenceto company, its reputation. The aim of the research is to find better risk management improvement decisions, using techniquesthat could help to reduce risk impact in wood-based nonstandard production with shorter project time, smoother design process,lower costs, better project coordination, increased ability to manage problems, technical solutions.

  7. Optimisation of 20 kHz sonoreactor geometry on the basis of numerical simulation of local ultrasonic intensity and qualitative comparison with experimental results

    Czech Academy of Sciences Publication Activity Database

    Klíma, Jiří; Frias-Ferrer, A.; González-Garcia, J.; Ludvík, Jiří; Sáez, V.; Iniesta, J.

    2007-01-01

    Roč. 14, č. 1 (2007), s. 19-28 ISSN 1350-4177 R&D Projects: GA MŠk(CZ) OC D32.001; GA MŠk 1P05OC074; GA AV ČR IAA4040304 Grant - others:Generalidad Valenciana(ES) GV05/104 Institutional research plan: CEZ:AV0Z40400503 Keywords : ultrasound * intensity distribution * cell geometry optimisation * wave equation Subject RIV: CG - Electrochemistry Impact factor: 2.434, year: 2007

  8. Optimised dipper fine tunes shovel performance

    Energy Technology Data Exchange (ETDEWEB)

    Fiscor, S.

    2005-06-01

    Joint efforts between mine operators, OEMs, and researchers yields unexpected benefits from dippers for shovels for coal, oil, or hardrock mining that can now be tailored to meet site-specific conditions. The article outlines a process being developed by CRCMining and P & H MIning Equipment to optimise the dipper that involves rapid prototyping and scale modelling of the dipper and the mine conditions. Scale models have been successfully field tested. 2 photos.

  9. Statistical Optimisation of Fermentation Conditions for Citric Acid ...

    African Journals Online (AJOL)

    This study investigated the optimisation of fermentation conditions during citric acid production via solid state fermentation (SSF) of pineapple peels using Aspergillus niger. A three-variable, three-level Box-Behnken design (BBD) comprising 17 experimental runs was used to develop a statistical model for the fermentation ...

  10. optimisation of compressive strength of periwinkle shell aggregate

    African Journals Online (AJOL)

    user

    2017-01-01

    Jan 1, 2017 ... In this paper, a regression model is developed to predict and optimise the compressive strength of periwinkle shell aggregate concrete using Scheffe's regression theory. The results obtained from the derived regression model agreed favourably with the experimental data. The model was tested for ...

  11. Design of optimised backstepping controller for the synchronisation

    Indian Academy of Sciences (India)

    In this paper, an adaptive backstepping controller has been tuned to synchronise two chaotic Colpitts oscillators in a master–slave configuration. The parameters of the controller are determined using shark smell optimisation (SSO) algorithm. Numerical results are presented and compared with those of particle swarm ...

  12. Need for New Optimisation Strategies in CR and Direct Digital Radiography

    International Nuclear Information System (INIS)

    Busch, H.P.

    2000-01-01

    Digital imaging techniques such as Digital Image Intensifier Radiography and Digital Storage Phosphor (Selenium) Radiography are replacing conventional film-screen radiography more and more. The aim of this development is the extension of diagnostic capabilities and the reduction of side effects such as radiation dose. Conventional film-screen radiography and digital radiography are very different ways of imaging. For digital radiography specific post-processing is the link between imaging conditions and film documentation. Optimisation of the images includes new possibilities of post-processing and a broad range for variation of the dose. Especially in fluoroscopy, dose can be reduced significantly by new technical features like pulsed fluoroscopy. For digital radiography the European guidelines on quality criteria have to be applied to projection radiography, digital subtraction radiography and to fluoroscopy. Further work should lead to a definition of reference values for the dose and the image quality. This has to be done first for single exposures and fluoroscopic mode and secondly for diagnostic and interventional procedures. (author)

  13. The optimisation of a water distribution system using Bentley WaterGEMS software

    Directory of Open Access Journals (Sweden)

    Świtnicka Karolina

    2017-01-01

    Full Text Available The proper maintenance of water distribution systems (WDSs requires from operators multiple actions in order to ensure optimal functioning. Usually, all requirements should be adjusted simultaneously. Therefore, the decision-making process is often supported by multi-criteria optimisation methods. Significant improvements of exploitation conditions of WDSs functioning can be achieved by connecting small water supply networks into group systems. Among many potential tools supporting advanced maintenance and management of WDSs, significant improvements have tools that can find the optimal solution by the implemented mechanism of metaheuristic methods, such as the genetic algorithm. In this paper, an exemplary WDS functioning optimisation is presented, in relevance to a group water supply system. The action range of optimised parameters included: maximisation of water flow velocity, regulation of pressure head, minimisation of water retention time in a network (water age and minimisation of pump energy consumption. All simulations were performed in Bentley WaterGEMS software.

  14. Methodology implementation for multi objective optimisation for nuclear fleet evolution scenarios

    International Nuclear Information System (INIS)

    Freynet, David

    2016-01-01

    The issue of the evolution French nuclear fleet can be considered through the study of nuclear transition scenarios. These studies are of paramount importance as their results can greatly affect the decision making process, given that they take into account industrial concerns, investments, time, and nuclear system complexity. Such studies can be performed with the COSI code (developed at the CEA/DEN), which enables the calculation of matter inventories and fluxes across the fuel cycle (nuclear reactors and associated facilities), especially when coupled with the CESAR depletion code. The studies today performed with COSI require the definition of the various scenarios' input parameters, in order to fulfil different objectives such as minimising natural uranium consumption, waste production and so on. These parameters concern the quantities and the scheduling of spent fuel destined for reprocessing, and the number, the type and the commissioning dates of deployed reactors.This work aims to develop, validate and apply an optimisation methodology coupled with COSI, in order to determine optimal nuclear transition scenarios for a multi-objective platform. Firstly, this methodology is based on the acceleration of scenario evaluation, enabling the use of optimisation methods in a reasonable time-frame. With this goal in mind, artificial neural network irradiation surrogate models are created with the URANIE platform (developed at the CEA/DEN) and are implemented within COSI. The next step in this work is to use, adapt and compare different optimisation methods, such as URANIE's genetic algorithm and particle swarm methods, in order to define a methodology suited to this type of study. This methodology development is based on an incremental approach which progressively adds objectives, constraints and decision variables to the optimisation problem definition. The variables added, which are related to reactor deployment and spent fuel reprocessing strategies, are chosen

  15. Optimisation of occupational exposure

    International Nuclear Information System (INIS)

    Webb, G.A.M.; Fleishman, A.B.

    1982-01-01

    The general concept of the optimisation of protection of the public is briefly described. Some ideas being developed for extending the cost benefit framework to include radiation workers with full implementation of the ALARA criterion are described. The role of cost benefit analysis in radiological protection and the valuation of health detriment including the derivation of monetary values and practical implications are discussed. Cost benefit analysis can lay out for inspection the doses, the associated health detriment costs and the costs of protection for alternative courses of action. However it is emphasised that the cost benefit process is an input to decisions on what is 'as low as reasonably achievable' and not a prescription for making them. (U.K.)

  16. Shielding optimisation of the ITER ICH&CD antenna for shutdown dose rate

    International Nuclear Information System (INIS)

    Turner, Andrew; Leichtle, Dieter; Lamalle, Philippe; Levesy, Bruno; Meunier, Lionel; Polunovskiy, Eduard; Sartori, Roberta; Shannon, Mark

    2015-01-01

    Highlights: • Neutronics analysis on the ITER ICH&CD system conducted to reduce shutdown dose rate. • Several designs for shielding the port plug gaps were modelled. • Shielding significantly reduced interspace dose rate but still exceed project requirements. • Design optimisation of the ICH port is continuing. • Significant contributions from other ports require an integrated modelling approach. - Abstract: The Ion Cyclotron Heating and Current Drive (ICH&CD) system will reside in ITER equatorial port plugs 13 and 15. Shutdown dose rates (SDDR) within the port interspace are required to be less than 100 μSv/h at 10 6 s cooling. A significant contribution to the SDDR results from neutrons streaming down gaps around the port frame, and the mitigation of this streaming is the main subject of these analyses. An updated MCNP model of the antenna was created and integrated into an ITER reference model. Shielding plates were defined in the port gaps, and scoping studies conducted to assess their effectiveness in several configurations, based on which a front dog-leg arrangement was selected for high resolution 3-D activation analysis using MCR2S. It was concluded that the selected configuration reduced the SDDR from ∼500 μSv/h to 220 μSv/h but were still in excess of dose rate requirements. Approximately 30% of this was due to cross-talk from neighbouring ports. In addition, increased dose rates were observed in the port interspace along the lines of sight of the removable vacuum transmission lines. Design optimisation is continuing, however an integrated approach is needed with regard to ITER port plug design and the shielding of surrounding systems.

  17. Shielding optimisation of the ITER ICH&CD antenna for shutdown dose rate

    Energy Technology Data Exchange (ETDEWEB)

    Turner, Andrew, E-mail: andrew.turner@ccfe.ac.uk [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Leichtle, Dieter [Fusion for Energy, Josep Pla 2, Torres Diagonal Litoral B3, 08019 Barcelona (Spain); Lamalle, Philippe; Levesy, Bruno [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St., Paul-lez-Durance (France); Meunier, Lionel [Fusion for Energy, Josep Pla 2, Torres Diagonal Litoral B3, 08019 Barcelona (Spain); Polunovskiy, Eduard [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St., Paul-lez-Durance (France); Sartori, Roberta [Fusion for Energy, Josep Pla 2, Torres Diagonal Litoral B3, 08019 Barcelona (Spain); Shannon, Mark [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom)

    2015-10-15

    Highlights: • Neutronics analysis on the ITER ICH&CD system conducted to reduce shutdown dose rate. • Several designs for shielding the port plug gaps were modelled. • Shielding significantly reduced interspace dose rate but still exceed project requirements. • Design optimisation of the ICH port is continuing. • Significant contributions from other ports require an integrated modelling approach. - Abstract: The Ion Cyclotron Heating and Current Drive (ICH&CD) system will reside in ITER equatorial port plugs 13 and 15. Shutdown dose rates (SDDR) within the port interspace are required to be less than 100 μSv/h at 10{sup 6} s cooling. A significant contribution to the SDDR results from neutrons streaming down gaps around the port frame, and the mitigation of this streaming is the main subject of these analyses. An updated MCNP model of the antenna was created and integrated into an ITER reference model. Shielding plates were defined in the port gaps, and scoping studies conducted to assess their effectiveness in several configurations, based on which a front dog-leg arrangement was selected for high resolution 3-D activation analysis using MCR2S. It was concluded that the selected configuration reduced the SDDR from ∼500 μSv/h to 220 μSv/h but were still in excess of dose rate requirements. Approximately 30% of this was due to cross-talk from neighbouring ports. In addition, increased dose rates were observed in the port interspace along the lines of sight of the removable vacuum transmission lines. Design optimisation is continuing, however an integrated approach is needed with regard to ITER port plug design and the shielding of surrounding systems.

  18. Optimisation of wheat-sprouted soybean flour bread using response ...

    African Journals Online (AJOL)

    STORAGESEVER

    2009-11-16

    Nov 16, 2009 ... Full Length Research Paper. Optimisation of ... Victoria A. Jideani1* and Felix C. Onwubali2. 1Department of Food Technology, Cape Peninsula University of Technology, P. O. Box 652, Cape Town 8000, South. Africa.

  19. Issues with performance measures for dynamic multi-objective optimisation

    CSIR Research Space (South Africa)

    Helbig, M

    2013-06-01

    Full Text Available Symposium on Computational Intelligence in Dynamic and Uncertain Environments (CIDUE), Mexico, 20-23 June 2013 Issues with Performance Measures for Dynamic Multi-objective Optimisation Mard´e Helbig CSIR: Meraka Institute Brummeria, South Africa...

  20. Process and Economic Optimisation of a Milk Processing Plant with Solar Thermal Energy

    DEFF Research Database (Denmark)

    Bühler, Fabian; Nguyen, Tuong-Van; Elmegaard, Brian

    2016-01-01

    . Based on the case study of a dairy factory, where first a heat integration is performed to optimise the system, a model for solar thermal process integration is developed. The detailed model is based on annual hourly global direct and diffuse solar radiation, from which the radiation on a defined......This work investigates the integration of solar thermal systems for process energy use. A shift from fossil fuels to renewable energy could be beneficial both from environmental and economic perspectives, after the process itself has been optimised and efficiency measures have been implemented...... surface is calculated. Based on hourly process stream data from the dairy factory, the optimal streams for solar thermal process integration are found, with an optimal thermal storagetank volume. The last step consists of an economic optimisation of the problem to determine the optimal size...

  1. Development of an Optimised Losartan Potassium Press-Coated ...

    African Journals Online (AJOL)

    The optimised formulation was further characterized with Fourier-transform infrared spectroscopy (FTIR) and powder X-ray diffractometry (PXRD) to investigate any drug/excipient modifications/interactions. Results: The tensile strength values of all the PCT were between 1.12 and 1.23MNm-2 and friability was < 0.36 %.

  2. Evidos: optimisation of individual monitoring in mixed neutron/photon fields at workplaces of the nuclear fuel cycle

    International Nuclear Information System (INIS)

    Luszik-Bhadra, M.; Reginatto, M.; Schuhmacher, H.; Lacoste, V.; Muller, M.; Boschung, M.; Fiechtner, A.; Coeck, M.; Vanhavere, F.; Curzio, G.; D'errico, F.; Kyllonen, J.E.; Lindborg, L.; Molinos, C.; Tanner, R.; Derdau, D.; Lahaye, Th.

    2005-01-01

    Within its 5. Framework Programme, the EC is funding the project EVIDOS ('Evaluation of Individual Dosimetry in Mixed Neutron and Photon Radiation Fields'). The aim of this project is the optimisation of individual monitoring at workplaces of the nuclear fuel cycle with special regard to neutrons. Various dosemeters for mixed field application - passive and new electronic devices - are tested in selected workplace fields in nuclear installations in Europe. The fields are characterised using a series of spectrometers that provide the energy distribution of neutron fluence (Bonner spheres) and newly developed devices that provide the energy and directional distribution of the neutron fluence. Results from the first measurement campaign, carried out in simulated workplace fields (IRSN, Cadarache. France), and those of a second measurement campaign, carried out at workplaces at a boiling water reactor and at a storage cask with used fuel elements (Kernkraftwerk Kriimmel, Germany), are described. (authors)

  3. Thermal performance monitoring and optimisation

    International Nuclear Information System (INIS)

    Sunde, Svein; Berg; Oeyvind

    1998-01-01

    Monitoring of the thermal efficiency of nuclear power plants is expected to become increasingly important as energy-market liberalisation exposes plants to increasing availability requirements and fiercer competition. The general goal in thermal performance monitoring is straightforward: to maximise the ratio of profit to cost under the constraints of safe operation. One may perceive this goal to be pursued in two ways, one oriented towards fault detection and cost-optimal predictive maintenance, and another determined at optimising target values of parameters in response to any component degradation detected, changes in ambient conditions, or the like. Annual savings associated with effective thermal-performance monitoring are expected to be in the order of $ 100 000 for power plants of representative size. A literature review shows that a number of computer systems for thermal-performance monitoring exists, either as prototypes or commercially available. The characteristics and needs of power plants may vary widely, however, and decisions concerning the exact scope, content and configuration of a thermal-performance monitor may well follow a heuristic approach. Furthermore, re-use of existing software modules may be desirable. Therefore, we suggest here the design of a flexible workbench for easy assembly of an experimental thermal-performance monitor at the Halden Project. The suggested design draws heavily on our extended experience in implementing control-room systems featured by assets like high levels of customisation, flexibility in configuration and modularity in structure, and on a number of relevant adjoining activities. The design includes a multi-computer communication system and a graphical user's interface, and aims at a system adaptable to any combination of in-house or end user's modules, as well as commercially available software. (author)

  4. Numerical Analysis and Geometry Optimisation of Vertical Vane of Room Air-conditioner

    Directory of Open Access Journals (Sweden)

    Al-Obaidi Abdulkareem Sh. Mahdi

    2018-01-01

    Full Text Available Vertical vanes of room air-conditioners are used to control and direct cold air. This paper aims to study vertical vane as one of the parameters that affect the efficiency of dissipating cold air to a given space. The vertical vane geometry is analysed and optimised for lower production cost using CFD. The optimised geometry of the vertical vane should have the same or increased efficiency of dissipating cold air and have lesser mass compared to the existing original design. The existing original design of vertical vane is simplified and analysed by using ANSYS Fluent. Efficiency of wind direction is define as how accurate the direction of airflow coming out from vertical vane. In order to calculate the efficiency of wind direction, 15° and 30° rotation of vertical vane inside room air-conditioner are simulated. The efficiency of wind direction for 15° rotation of vertical vane is 57.81% while efficiency of wind direction for 30° rotation of vertical vane is 47.54%. The results of the efficiency of wind direction are used as base reference for parametric study. The parameters investigated for optimisation of vertical vane are focused at length of long span, tip chord and short span. The design of 15% decreased in vane surface area at tip chord is the best optimised design of vertical vane because the efficiency of wind direction is the highest as 60.32%.

  5. Influence of design improvements in optimising staffing of NPPs - an Indian experience

    International Nuclear Information System (INIS)

    Bhattacharya, A.S.

    2001-01-01

    Three decades of operating experience in India has led to sustained high performance of NPP's. The staffing modules and policies are standardised. The basic functions of operation, maintenance, technical support and quality assurance are carried out by a team of 727 in-plant persons (for a 2 x 220 MW PHWR station) organised at five levels, for fifty positions in ten job families. The organisational factors that led to optimising of staff are described in the companion paper. This optimisation of manpower is a result of continuous learning - for (i) optimising quantum of workload and (ii) improving productivity. For the first category, design improvements over older Indian NPP's have increased reliability, operability, maintainability and human factors. Few examples: (i) improved man-machine interface in plant controls and on-power refuelling system with operator guidance, logging as well as diagnostic/health monitoring features; (ii) spread out layout for better access and ease of maintenance, separation of plant services for unit-1 from unit-2 and, removal of reactor auxiliaries out to separate buildings; (iii) reduction of maintenance tasks through redesigned equipment and improved condition monitoring means. However, design and procedural improvements also include additional equipment for upgradation of safety measures, e.g. larger number of safety related pumps separate switchyard control room and increased service system equipment. This paper outlines experience of design improvements in optimising staffing and uses a specific case illustration to establish the findings for better use of staff. (author)

  6. A critical evaluation of the STRATEGY project

    DEFF Research Database (Denmark)

    Howard, B.J.; Liland, A.; Beresford, N.A.

    2004-01-01

    The STRATEGY project (sustainable restoration and long-term management of contaminated rural, urban and industrial ecosystems; www.strategy-ec.org.uk) addressed the need for a holistic decision framework for the selection of optimal remediation strategies for long-term sustainable management...... of contaminated areas in Western Europe. The project considered both technical and social aspects of implementing restoration strategies for urban and rural environments. The importance of considering socially relevant objectives in addition to the dose reduction was emphasised. A critical evaluation was carried...... out on 101 selected countermeasures, (including rural waste disposal options), a model was developed to aid optimising countermeasure strategies and a method of carrying out participatory decision-making suggested. The outputs of the project are described and critically evaluated....

  7. A critical evaluation of the strategy project

    International Nuclear Information System (INIS)

    Howard, B. J.; Liland, A.; Beresford, N. A.; Andersson, K. G.; Cox, G.; Gil, J. M.; Hunt, J.; Nisbet, A.; Oughton, D. H.; Voigt, G.

    2004-01-01

    The STRATEGY project (sustainable restoration and long-term management of contaminated rural, urban and industrial ecosystems; www.strategy-ec.org.uk) addressed the need for a holistic decision framework for the selection of optimal remediation strategies for long-term sustainable management of contaminated areas in Western Europe. The project considered both technical and social aspects of implementing restoration strategies for urban and rural environments. The importance of considering socially relevant objectives in addition to the dose reduction was emphasised. A critical evaluation was carried out on 101 selected countermeasures, (including rural waste disposal options), a model was developed to aid optimising countermeasure strategies and a method of carrying out participatory decision-making suggested. The outputs of the project are described and critically evaluated. (authors)

  8. Weight Optimisation of Steel Monopile Foundations for Offshore Windfarms

    DEFF Research Database (Denmark)

    Fog Gjersøe, Nils; Bouvin Pedersen, Erik; Kristensen, Brian

    2015-01-01

    The potential for mass reduction of monopiles in offshore windfarms using current design practice is investigated. Optimisation by sensitivity analysis is carried out for the following important parameters: wall thickness distribution between tower and monopile, soil stiffness, damping ratio...

  9. Larval feeding inhibition assay – need for optimisation

    DEFF Research Database (Denmark)

    Azuhnwi, Blasius; Desrues, O.; Hoste, H.

    2013-01-01

    for this observed variation in results include: parasite (species/strain); material tested; or season. There is thus need to optimise LFIA to permit intra and inter-laboratory comparison of results. We investigate here, if changes in EC50 values occur over the patency phase of a nematode species using two test...

  10. Optimisation Study on the Production of Anaerobic Digestate ...

    African Journals Online (AJOL)

    Organic fraction of municipal solid waste (OFMSW) is a rich substrate for biogas and compost production. Anaerobic Digestate compost (ADC) is an organic fertilizer produced from stabilized residuals of anaerobic digestion of OFMSW. This paper reports the result of studies carried out to optimise the production of ADC from ...

  11. Design optimisation of powers-of-two FIR filter using self-organising random immigrants GA

    Science.gov (United States)

    Chandra, Abhijit; Chattopadhyay, Sudipta

    2015-01-01

    In this communication, we propose a novel design strategy of multiplier-less low-pass finite impulse response (FIR) filter with the aid of a recent evolutionary optimisation technique, known as the self-organising random immigrants genetic algorithm. Individual impulse response coefficients of the proposed filter have been encoded as sum of signed powers-of-two. During the formulation of the cost function for the optimisation algorithm, both the frequency response characteristic and the hardware cost of the discrete coefficient FIR filter have been considered. The role of crossover probability of the optimisation technique has been evaluated on the overall performance of the proposed strategy. For this purpose, the convergence characteristic of the optimisation technique has been included in the simulation results. In our analysis, two design examples of different specifications have been taken into account. In order to substantiate the efficiency of our proposed structure, a number of state-of-the-art design strategies of multiplier-less FIR filter have also been included in this article for the purpose of comparison. Critical analysis of the result unambiguously establishes the usefulness of our proposed approach for the hardware efficient design of digital filter.

  12. Group search optimiser-based optimal bidding strategies with no Karush-Kuhn-Tucker optimality conditions

    Science.gov (United States)

    Yadav, Naresh Kumar; Kumar, Mukesh; Gupta, S. K.

    2017-03-01

    General strategic bidding procedure has been formulated in the literature as a bi-level searching problem, in which the offer curve tends to minimise the market clearing function and to maximise the profit. Computationally, this is complex and hence, the researchers have adopted Karush-Kuhn-Tucker (KKT) optimality conditions to transform the model into a single-level maximisation problem. However, the profit maximisation problem with KKT optimality conditions poses great challenge to the classical optimisation algorithms. The problem has become more complex after the inclusion of transmission constraints. This paper simplifies the profit maximisation problem as a minimisation function, in which the transmission constraints, the operating limits and the ISO market clearing functions are considered with no KKT optimality conditions. The derived function is solved using group search optimiser (GSO), a robust population-based optimisation algorithm. Experimental investigation is carried out on IEEE 14 as well as IEEE 30 bus systems and the performance is compared against differential evolution-based strategic bidding, genetic algorithm-based strategic bidding and particle swarm optimisation-based strategic bidding methods. The simulation results demonstrate that the obtained profit maximisation through GSO-based bidding strategies is higher than the other three methods.

  13. Optimisation of optical receiver for 10 Gbit/s optical duobinary transmission system

    DEFF Research Database (Denmark)

    Zheng, Xueyan; Liu, Fenghai; Jeppesen, Palle

    2001-01-01

    Optimisation of a receiver for an optical duobinary signal is studied numerically. It is shown that a conventional receiver is not optimum neither when a DCF is used before the receiver nor without a DCF being used. The optimum receiver for an optical duobinary system is identified.......Optimisation of a receiver for an optical duobinary signal is studied numerically. It is shown that a conventional receiver is not optimum neither when a DCF is used before the receiver nor without a DCF being used. The optimum receiver for an optical duobinary system is identified....

  14. A New Computational Technique for the Generation of Optimised Aircraft Trajectories

    Science.gov (United States)

    Chircop, Kenneth; Gardi, Alessandro; Zammit-Mangion, David; Sabatini, Roberto

    2017-12-01

    A new computational technique based on Pseudospectral Discretisation (PSD) and adaptive bisection ɛ-constraint methods is proposed to solve multi-objective aircraft trajectory optimisation problems formulated as nonlinear optimal control problems. This technique is applicable to a variety of next-generation avionics and Air Traffic Management (ATM) Decision Support Systems (DSS) for strategic and tactical replanning operations. These include the future Flight Management Systems (FMS) and the 4-Dimensional Trajectory (4DT) planning and intent negotiation/validation tools envisaged by SESAR and NextGen for a global implementation. In particular, after describing the PSD method, the adaptive bisection ɛ-constraint method is presented to allow an efficient solution of problems in which two or multiple performance indices are to be minimized simultaneously. Initial simulation case studies were performed adopting suitable aircraft dynamics models and addressing a classical vertical trajectory optimisation problem with two objectives simultaneously. Subsequently, a more advanced 4DT simulation case study is presented with a focus on representative ATM optimisation objectives in the Terminal Manoeuvring Area (TMA). The simulation results are analysed in-depth and corroborated by flight performance analysis, supporting the validity of the proposed computational techniques.

  15. A reliability-based maintenance technicians' workloads optimisation model with stochastic consideration

    Science.gov (United States)

    Ighravwe, D. E.; Oke, S. A.; Adebiyi, K. A.

    2016-06-01

    The growing interest in technicians' workloads research is probably associated with the recent surge in competition. This was prompted by unprecedented technological development that triggers changes in customer tastes and preferences for industrial goods. In a quest for business improvement, this worldwide intense competition in industries has stimulated theories and practical frameworks that seek to optimise performance in workplaces. In line with this drive, the present paper proposes an optimisation model which considers technicians' reliability that complements factory information obtained. The information used emerged from technicians' productivity and earned-values using the concept of multi-objective modelling approach. Since technicians are expected to carry out routine and stochastic maintenance work, we consider these workloads as constraints. The influence of training, fatigue and experiential knowledge of technicians on workload management was considered. These workloads were combined with maintenance policy in optimising reliability, productivity and earned-values using the goal programming approach. Practical datasets were utilised in studying the applicability of the proposed model in practice. It was observed that our model was able to generate information that practicing maintenance engineers can apply in making more informed decisions on technicians' management.

  16. Smart optimisation and sensitivity analysis in water distribution systems

    CSIR Research Space (South Africa)

    Page, Philip R

    2015-12-01

    Full Text Available optimisation of a water distribution system by keeping the average pressure unchanged as water demands change, by changing the speed of the pumps. Another application area considered, using the same mathematical notions, is the study of the sensitivity...

  17. Optimisation combinatoire Theorie et algorithmes

    CERN Document Server

    Korte, Bernhard; Fonlupt, Jean

    2010-01-01

    Ce livre est la traduction fran aise de la quatri me et derni re dition de Combinatorial Optimization: Theory and Algorithms crit par deux minents sp cialistes du domaine: Bernhard Korte et Jens Vygen de l'universit de Bonn en Allemagne. Il met l accent sur les aspects th oriques de l'optimisation combinatoire ainsi que sur les algorithmes efficaces et exacts de r solution de probl mes. Il se distingue en cela des approches heuristiques plus simples et souvent d crites par ailleurs. L ouvrage contient de nombreuses d monstrations, concises et l gantes, de r sultats difficiles. Destin aux tudia

  18. Probabilistic sensitivity analysis of optimised preventive maintenance strategies for deteriorating infrastructure assets

    International Nuclear Information System (INIS)

    Daneshkhah, A.; Stocks, N.G.; Jeffrey, P.

    2017-01-01

    Efficient life-cycle management of civil infrastructure systems under continuous deterioration can be improved by studying the sensitivity of optimised preventive maintenance decisions with respect to changes in model parameters. Sensitivity analysis in maintenance optimisation problems is important because if the calculation of the cost of preventive maintenance strategies is not sufficiently robust, the use of the maintenance model can generate optimised maintenances strategies that are not cost-effective. Probabilistic sensitivity analysis methods (particularly variance based ones), only partially respond to this issue and their use is limited to evaluating the extent to which uncertainty in each input contributes to the overall output's variance. These methods do not take account of the decision-making problem in a straightforward manner. To address this issue, we use the concept of the Expected Value of Perfect Information (EVPI) to perform decision-informed sensitivity analysis: to identify the key parameters of the problem and quantify the value of learning about certain aspects of the life-cycle management of civil infrastructure system. This approach allows us to quantify the benefits of the maintenance strategies in terms of expected costs and in the light of accumulated information about the model parameters and aspects of the system, such as the ageing process. We use a Gamma process model to represent the uncertainty associated with asset deterioration, illustrating the use of EVPI to perform sensitivity analysis on the optimisation problem for age-based and condition-based preventive maintenance strategies. The evaluation of EVPI indices is computationally demanding and Markov Chain Monte Carlo techniques would not be helpful. To overcome this computational difficulty, we approximate the EVPI indices using Gaussian process emulators. The implications of the worked numerical examples discussed in the context of analytical efficiency and organisational

  19. Public transport optimisation emphasising passengers’ travel behaviour.

    OpenAIRE

    Jensen, Jens Parbo; Nielsen, Otto Anker; Prato, Carlo Giacomo

    2015-01-01

    Passengers in public transport complaining about their travel experiences are not uncommon. This might seem counterintuitive since several operators worldwide are presenting better key performance indicators year by year. The present PhD study focuses on developing optimisation algorithms to enhance the operations of public transport while explicitly emphasising passengers’ travel behaviour and preferences. Similar to economic theory, interactions between supply and demand are omnipresent in ...

  20. Optimal design and operation of a photovoltaic-electrolyser system using particle swarm optimisation

    Science.gov (United States)

    Sayedin, Farid; Maroufmashat, Azadeh; Roshandel, Ramin; Khavas, Sourena Sattari

    2016-07-01

    In this study, hydrogen generation is maximised by optimising the size and the operating conditions of an electrolyser (EL) directly connected to a photovoltaic (PV) module at different irradiance. Due to the variations of maximum power points of the PV module during a year and the complexity of the system, a nonlinear approach is considered. A mathematical model has been developed to determine the performance of the PV/EL system. The optimisation methodology presented here is based on the particle swarm optimisation algorithm. By this method, for the given number of PV modules, the optimal sizeand operating condition of a PV/EL system areachieved. The approach can be applied for different sizes of PV systems, various ambient temperatures and different locations with various climaticconditions. The results show that for the given location and the PV system, the energy transfer efficiency of PV/EL system can reach up to 97.83%.

  1. Work management to optimise occupational radiological protection

    International Nuclear Information System (INIS)

    Ahier, B.

    2009-01-01

    Although work management is no longer a new concept, continued efforts are still needed to ensure that good performance, outcomes and trends are maintained in the face of current and future challenges. The ISOE programme thus created an Expert Group on Work Management in 2007 to develop an updated report reflecting the current state of knowledge, technology and experience in the occupational radiological protection of workers at nuclear power plants. Published in 2009, the new ISOE report on Work Management to Optimise Occupational Radiological Protection in the Nuclear Power Industry provides up-to-date practical guidance on the application of work management principles. Work management measures aim at optimising occupational radiological protection in the context of the economic viability of the installation. Important factors in this respect are measures and techniques influencing i) dose and dose rate, including source- term reduction; ii) exposure, including amount of time spent in controlled areas for operations; and iii) efficiency in short- and long-term planning, worker involvement, coordination and training. Equally important due to their broad, cross-cutting nature are the motivational and organisational arrangements adopted. The responsibility for these aspects may reside in various parts of an installation's organisational structure, and thus, a multi-disciplinary approach must be recognised, accounted for and well-integrated in any work. Based on the operational experience within the ISOE programme, the following key areas of work management have been identified: - regulatory aspects; - ALARA management policy; - worker involvement and performance; - work planning and scheduling; - work preparation; - work implementation; - work assessment and feedback; - ensuring continuous improvement. The details of each of these areas are elaborated and illustrated in the report through examples and case studies arising from ISOE experience. They are intended to

  2. Reference voltage calculation method based on zero-sequence component optimisation for a regional compensation DVR

    Science.gov (United States)

    Jian, Le; Cao, Wang; Jintao, Yang; Yinge, Wang

    2018-04-01

    This paper describes the design of a dynamic voltage restorer (DVR) that can simultaneously protect several sensitive loads from voltage sags in a region of an MV distribution network. A novel reference voltage calculation method based on zero-sequence voltage optimisation is proposed for this DVR to optimise cost-effectiveness in compensation of voltage sags with different characteristics in an ungrounded neutral system. Based on a detailed analysis of the characteristics of voltage sags caused by different types of faults and the effect of the wiring mode of the transformer on these characteristics, the optimisation target of the reference voltage calculation is presented with several constraints. The reference voltages under all types of voltage sags are calculated by optimising the zero-sequence component, which can reduce the degree of swell in the phase-to-ground voltage after compensation to the maximum extent and can improve the symmetry degree of the output voltages of the DVR, thereby effectively increasing the compensation ability. The validity and effectiveness of the proposed method are verified by simulation and experimental results.

  3. CFD optimisation of a stadium roof geometry: a qualitative study to improve the wind microenvironment

    Directory of Open Access Journals (Sweden)

    Sofotasiou Polytimi

    2017-01-01

    Full Text Available The complexity of the built environment requires the adoption of coupled techniques to predict the flow phenomena and provide optimum design solutions. In this study, coupled computational fluid dynamics (CFD and response surface methodology (RSM optimisation tools are employed to investigate the parameters that determine the wind comfort in a two-dimensional stadium model, by optimising the roof geometry. The roof height, width and length are evaluated against the flow homogeneity at the spectator terraces and the playing field area, the roof flow rate and the average interior pressure. Based on non-parametric regression analysis, both symmetric and asymmetric configurations are considered for optimisation. The optimum design solutions revealed that it is achievable to provide an improved wind environment in both playing field area and spectator terraces, giving a further insight on the interrelations of the parameters involved. Considering the limitations of conducting a two-dimensional study, the obtained results may beneficially be used as a basis for the optimisation of a complex three-dimensional stadium structure and thus become an important design guide for stadium structures.

  4. MO-DE-204-03: Radiology Dose Optimisation - An Australian Perspective

    International Nuclear Information System (INIS)

    Schick, D.

    2016-01-01

    The main topic of the session is to show how dose optimization is being implemented in various regions of the world, including Europe, Australia, North America and other regions. A multi-national study conducted under International Atomic Energy Agency (IAEA) across more than 50 less resourced countries gave insight into patient radiation doses and safety practices in CT, mammography, radiography and interventional procedures, both for children and adults. An important outcome was the capability development on dose assessment and management. An overview of recent European projects related to CT radiation dose and optimization both to adults and children will be presented. Existing data on DRLs together with a European methodology proposed on establishing and using DRLs for paediatric radiodiagnostic imaging and interventional radiology practices will be shown. Compared with much of Europe at least, many Australian imaging practices are relatively new to the task of diagnostic imaging dose optimisation. In 2008 the Australian Government prescribed a requirement to periodically compare patient radiation doses with diagnostic reference levels (DRLs), where DRLs have been established. Until recently, Australia had only established DRLs for computed tomography (CT). Regardless, both professional society and individual efforts to improved data collection and develop optimisation strategies across a range of modalities continues. Progress in this field, principally with respect to CT and interventional fluoroscopy will be presented. In the US, dose reduction and optimization efforts for computed tomography have been promoted and mandated by several organizations and accrediting entities. This presentation will cover the general motivation, implementation, and implications of such efforts. Learning Objectives: Understand importance of the dose optimization in Diagnostic Radiology. See how this goal is achieved in different regions of the World. Learn about the global trend

  5. MO-DE-204-03: Radiology Dose Optimisation - An Australian Perspective

    Energy Technology Data Exchange (ETDEWEB)

    Schick, D. [Princess Alexandra Hospital (United States)

    2016-06-15

    The main topic of the session is to show how dose optimization is being implemented in various regions of the world, including Europe, Australia, North America and other regions. A multi-national study conducted under International Atomic Energy Agency (IAEA) across more than 50 less resourced countries gave insight into patient radiation doses and safety practices in CT, mammography, radiography and interventional procedures, both for children and adults. An important outcome was the capability development on dose assessment and management. An overview of recent European projects related to CT radiation dose and optimization both to adults and children will be presented. Existing data on DRLs together with a European methodology proposed on establishing and using DRLs for paediatric radiodiagnostic imaging and interventional radiology practices will be shown. Compared with much of Europe at least, many Australian imaging practices are relatively new to the task of diagnostic imaging dose optimisation. In 2008 the Australian Government prescribed a requirement to periodically compare patient radiation doses with diagnostic reference levels (DRLs), where DRLs have been established. Until recently, Australia had only established DRLs for computed tomography (CT). Regardless, both professional society and individual efforts to improved data collection and develop optimisation strategies across a range of modalities continues. Progress in this field, principally with respect to CT and interventional fluoroscopy will be presented. In the US, dose reduction and optimization efforts for computed tomography have been promoted and mandated by several organizations and accrediting entities. This presentation will cover the general motivation, implementation, and implications of such efforts. Learning Objectives: Understand importance of the dose optimization in Diagnostic Radiology. See how this goal is achieved in different regions of the World. Learn about the global trend

  6. Using response surface methodology in optimisation of biodiesel production via alkali catalysed transesterification of waste cooking oil

    CSIR Research Space (South Africa)

    Naidoo, R

    2016-03-01

    Full Text Available The report focuses on optimisation of alkali catalysis as a process for producing biodiesel from waste cooking oils. Biodiesel production parameters that were optimised were methanol to oil ratio, catalyst concentration, reaction temperature...

  7. Plant-wide performance optimisation – The refrigeration system case

    DEFF Research Database (Denmark)

    Green, Torben; Razavi-Far, Roozbeh; Izadi-Zamanabadi, Roozbeh

    2012-01-01

    applicationsin the process industry. The paper addresses the fact that dynamic performance of the system is important, to ensure optimal changes between different operation conditions. To enable optimisation of the dynamic controller behaviour a method for designing the required excitation signal is presented...

  8. MULTI-OBJECTIVE OPTIMISATION OF LASER CUTTING USING CUCKOO SEARCH ALGORITHM

    Directory of Open Access Journals (Sweden)

    M. MADIĆ

    2015-03-01

    Full Text Available Determining of optimal laser cutting conditions for improving cut quality characteristics is of great importance in process planning. This paper presents multi-objective optimisation of the CO2 laser cutting process considering three cut quality characteristics such as surface roughness, heat affected zone (HAZ and kerf width. It combines an experimental design by using Taguchi’s method, modelling the relationships between the laser cutting factors (laser power, cutting speed, assist gas pressure and focus position and cut quality characteristics by artificial neural networks (ANNs, formulation of the multiobjective optimisation problem using weighting sum method, and solving it by the novel meta-heuristic cuckoo search algorithm (CSA. The objective is to obtain optimal cutting conditions dependent on the importance order of the cut quality characteristics for each of four different case studies presented in this paper. The case studies considered in this study are: minimisation of cut quality characteristics with equal priority, minimisation of cut quality characteristics with priority given to surface roughness, minimisation of cut quality characteristics with priority given to HAZ, and minimisation of cut quality characteristics with priority given to kerf width. The results indicate that the applied CSA for solving the multi-objective optimisation problem is effective, and that the proposed approach can be used for selecting the optimal laser cutting factors for specific production requirements.

  9. Stress-optimised shape memory devices for the use in microvalves

    International Nuclear Information System (INIS)

    Skrobanek, K.D.; Kohl, M.; Miyazaki, S.

    1997-01-01

    A gas valve of 6 x 6 x 2 mm 3 size has been developed for high pressure applications. Stress-optimised shape memory microbeams of 100 μm thickness are used to control the deflection of a membrane above a valve chamber. The shape memory thin sheets have been fabricated by melting and rolling, which creates specific textures. Investigations by X-ray diffraction revealed major orientations of [111] and [011] in rolling direction. The corresponding maximum anisotropy of transformation strain was 20%. The microbeams have been fabricated by laser cutting. For stress-optimisation, the lateral widths of the beams are designed for homogeneous stress distributions along the beam surfaces allowing an optimised use of the shape memory effect and a minimisation of fatigue effects. For actuation, a rhombohedral phase transformation is used. This allows operation below pressure differences of 1200 hPa in designs with one valve chamber and below 4500 hPa in pressure-compensated designs with a second valve chamber above the membrane. Maximum gas flows of 1600 seem (seem cm 2 at standart conditions/minute) and work outputs of 35 μNm are achieved for a driving power of 210 mW. The response times for closing the valves vary between 0.5 and 1.2 s and for opening between 1 and 2 s depending on the applied pressure difference. (orig.)

  10. 3D printed fluidics with embedded analytic functionality for automated reaction optimisation.

    Science.gov (United States)

    Capel, Andrew J; Wright, Andrew; Harding, Matthew J; Weaver, George W; Li, Yuqi; Harris, Russell A; Edmondson, Steve; Goodridge, Ruth D; Christie, Steven D R

    2017-01-01

    Additive manufacturing or '3D printing' is being developed as a novel manufacturing process for the production of bespoke micro- and milliscale fluidic devices. When coupled with online monitoring and optimisation software, this offers an advanced, customised method for performing automated chemical synthesis. This paper reports the use of two additive manufacturing processes, stereolithography and selective laser melting, to create multifunctional fluidic devices with embedded reaction monitoring capability. The selectively laser melted parts are the first published examples of multifunctional 3D printed metal fluidic devices. These devices allow high temperature and pressure chemistry to be performed in solvent systems destructive to the majority of devices manufactured via stereolithography, polymer jetting and fused deposition modelling processes previously utilised for this application. These devices were integrated with commercially available flow chemistry, chromatographic and spectroscopic analysis equipment, allowing automated online and inline optimisation of the reaction medium. This set-up allowed the optimisation of two reactions, a ketone functional group interconversion and a fused polycyclic heterocycle formation, via spectroscopic and chromatographic analysis.

  11. 3D printed fluidics with embedded analytic functionality for automated reaction optimisation

    Directory of Open Access Journals (Sweden)

    Andrew J. Capel

    2017-01-01

    Full Text Available Additive manufacturing or ‘3D printing’ is being developed as a novel manufacturing process for the production of bespoke micro- and milliscale fluidic devices. When coupled with online monitoring and optimisation software, this offers an advanced, customised method for performing automated chemical synthesis. This paper reports the use of two additive manufacturing processes, stereolithography and selective laser melting, to create multifunctional fluidic devices with embedded reaction monitoring capability. The selectively laser melted parts are the first published examples of multifunctional 3D printed metal fluidic devices. These devices allow high temperature and pressure chemistry to be performed in solvent systems destructive to the majority of devices manufactured via stereolithography, polymer jetting and fused deposition modelling processes previously utilised for this application. These devices were integrated with commercially available flow chemistry, chromatographic and spectroscopic analysis equipment, allowing automated online and inline optimisation of the reaction medium. This set-up allowed the optimisation of two reactions, a ketone functional group interconversion and a fused polycyclic heterocycle formation, via spectroscopic and chromatographic analysis.

  12. 3D printed fluidics with embedded analytic functionality for automated reaction optimisation

    Science.gov (United States)

    Capel, Andrew J; Wright, Andrew; Harding, Matthew J; Weaver, George W; Li, Yuqi; Harris, Russell A; Edmondson, Steve; Goodridge, Ruth D

    2017-01-01

    Additive manufacturing or ‘3D printing’ is being developed as a novel manufacturing process for the production of bespoke micro- and milliscale fluidic devices. When coupled with online monitoring and optimisation software, this offers an advanced, customised method for performing automated chemical synthesis. This paper reports the use of two additive manufacturing processes, stereolithography and selective laser melting, to create multifunctional fluidic devices with embedded reaction monitoring capability. The selectively laser melted parts are the first published examples of multifunctional 3D printed metal fluidic devices. These devices allow high temperature and pressure chemistry to be performed in solvent systems destructive to the majority of devices manufactured via stereolithography, polymer jetting and fused deposition modelling processes previously utilised for this application. These devices were integrated with commercially available flow chemistry, chromatographic and spectroscopic analysis equipment, allowing automated online and inline optimisation of the reaction medium. This set-up allowed the optimisation of two reactions, a ketone functional group interconversion and a fused polycyclic heterocycle formation, via spectroscopic and chromatographic analysis. PMID:28228852

  13. Current NRPB recommendations on optimisation of protection of workers

    International Nuclear Information System (INIS)

    Wrixon, A.D.

    1994-01-01

    The National Radiological Protection Board is required by Ministerial Direction to provide advice on the relevance of the recommendations of the International Commission on Radiological Protection to the UK. Its advice was published in the Spring of 1993 after a period of consultation. In this article, which formed the basis of a presentation at an SRP Meeting on 29 April 1994, the Board's advice on the optimisation of protection of workers is explored and presented in the context of the developments in the understanding of the principle that have taken place in recent years. The most significant developments are the realisation that implementation of the principle is an essential function of good management and the recognition that the interests of the individual are not sufficiently taken into account by the dose limits alone but doses to individuals should be both constrained and optimised. (author)

  14. Optimised sensitivity to leptonic CP violation from spectral information: the LBNO case at 2300 km baseline

    CERN Document Server

    Agarwalla, S K; Aittola, M; Alekou, A; Andrieu, B; Antoniou, F; Asfandiyarov, R; Autiero, D; Bésida, O; Balik, A; Ballett, P; Bandac, I; Banerjee, D; Bartmann, W; Bay, F; Biskup, B; Blebea-Apostu, A M; Blondel, A; Bogomilov, M; Bolognesi, S; Borriello, E; Brancus, I; Bravar, A; Buizza-Avanzini, M; Caiulo, D; Calin, M; Calviani, M; Campanelli, M; Cantini, C; Cata-Danil, G; Chakraborty, S; Charitonidis, N; Chaussard, L; Chesneanu, D; Chipesiu, F; Crivelli, P; Dawson, J; De Bonis, I; Declais, Y; Sanchez, P Del Amo; Delbart, A; Di Luise, S; Duchesneau, D; Dumarchez, J; Efthymiopoulos, I; Eliseev, A; Emery, S; Enqvist, T; Enqvist, K; Epprecht, L; Erykalov, A N; Esanu, T; Franco, D; Friend, M; Galymov, V; Gavrilov, G; Gendotti, A; Giganti, C; Gilardoni, S; Goddard, B; Gomoiu, C M; Gornushkin, Y A; Gorodetzky, P; Haesler, A; Hasegawa, T; Horikawa, S; Huitu, K; Izmaylov, A; Jipa, A; Kainulainen, K; Karadzhov, Y; Khabibullin, M; Khotjantsev, A; Kopylov, A N; Korzenev, A; Kosyanenko, S; Kryn, D; Kudenko, Y; Kuusiniemi, P; Lazanu, I; Lazaridis, C; Levy, J -M; Loo, K; Maalampi, J; Margineanu, R M; Marteau, J; Martin-Mari, C; Matveev, V; Mazzucato, E; Mefodiev, A; Mineev, O; Mirizzi, A; Mitrica, B; Murphy, S; Nakadaira, T; Narita, S; Nesterenko, D A; Nguyen, K; Nikolics, K; Noah, E; Novikov, Yu; Oprima, A; Osborne, J; Ovsyannikova, T; Papaphilippou, Y; Pascoli, S; Patzak, T; Pectu, M; Pennacchio, E; Periale, L; Pessard, H; Popov, B; Ravonel, M; Rayner, M; Resnati, F; Ristea, O; Robert, A; Rubbia, A; Rummukainen, K; Saftoiu, A; Sakashita, K; Sanchez-Galan, F; Sarkamo, J; Saviano, N; Scantamburlo, E; Sergiampietri, F; Sgalaberna, D; Shaposhnikova, E; Slupecki, M; Smargianaki, D; Stanca, D; Steerenberg, R; Sterian, A R; Sterian, P; Stoica, S; Strabel, C; Suhonen, J; Suvorov, V; Toma, G; Tonazzo, A; Trzaska, W H; Tsenov, R; Tuominen, K; Valram, M; Vankova-Kirilova, G; Vannucci, F; Vasseur, G; Velotti, F; Velten, P; Venturi, V; Viant, T; Vihonen, S; Vincke, H; Vorobyev, A; Weber, A; Wu, S; Yershov, N; Zambelli, L; Zito, M

    2014-01-01

    One of the main goals of the Long Baseline Neutrino Observatory (LBNO) is to study the $L/E$ behaviour (spectral information) of the electron neutrino and antineutrino appearance probabilities, in order to determine the unknown CP-violation phase $\\delta_{CP}$ and discover CP-violation in the leptonic sector. The result is based on the measurement of the appearance probabilities in a broad range of energies, covering t he 1st and 2nd oscillation maxima, at a very long baseline of 2300 km. The sensitivity of the experiment can be maximised by optimising the energy spectra of the neutrino and anti-neutrino fluxes. Such an optimisation requires exploring an extended range of parameters describing in details the geometries and properties of the primary protons, hadron target and focusing elements in the neutrino beam line. In this paper we present a numerical solution that leads to an optimised energy spectra and study its impact on the sensitivity of LBNO to discover leptonic CP violation. In the optimised flux ...

  15. Comparison of the genetic algorithm and incremental optimisation routines for a Bayesian inverse modelling based network design

    Science.gov (United States)

    Nickless, A.; Rayner, P. J.; Erni, B.; Scholes, R. J.

    2018-05-01

    The design of an optimal network of atmospheric monitoring stations for the observation of carbon dioxide (CO2) concentrations can be obtained by applying an optimisation algorithm to a cost function based on minimising posterior uncertainty in the CO2 fluxes obtained from a Bayesian inverse modelling solution. Two candidate optimisation methods assessed were the evolutionary algorithm: the genetic algorithm (GA), and the deterministic algorithm: the incremental optimisation (IO) routine. This paper assessed the ability of the IO routine in comparison to the more computationally demanding GA routine to optimise the placement of a five-member network of CO2 monitoring sites located in South Africa. The comparison considered the reduction in uncertainty of the overall flux estimate, the spatial similarity of solutions, and computational requirements. Although the IO routine failed to find the solution with the global maximum uncertainty reduction, the resulting solution had only fractionally lower uncertainty reduction compared with the GA, and at only a quarter of the computational resources used by the lowest specified GA algorithm. The GA solution set showed more inconsistency if the number of iterations or population size was small, and more so for a complex prior flux covariance matrix. If the GA completed with a sub-optimal solution, these solutions were similar in fitness to the best available solution. Two additional scenarios were considered, with the objective of creating circumstances where the GA may outperform the IO. The first scenario considered an established network, where the optimisation was required to add an additional five stations to an existing five-member network. In the second scenario the optimisation was based only on the uncertainty reduction within a subregion of the domain. The GA was able to find a better solution than the IO under both scenarios, but with only a marginal improvement in the uncertainty reduction. These results suggest

  16. Optimisation of dialysate flow in on-line hemodiafiltration

    Directory of Open Access Journals (Sweden)

    Francisco Maduell

    2015-09-01

    Conclusion: Qd variations in OL-HDF do not change convective volume. A higher Qd was associated to a slightly increased urea clearance with no change being observed for medium and large molecules. Qd optimisation to the minimal level assuring an adequate dialysis dose and allowing water and dialysate use to be rationalised should be recommended.

  17. Optimisation of compressed-air supply for control purposes at Valorec Services AG; Optimierung der Steuerluft - Versorgung bei der Valorec Services AG

    Energy Technology Data Exchange (ETDEWEB)

    Dott, R.; Afjei, T.

    2005-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) presents the results of a project that looked at the possibilities of optimising the supply of compressed air provided around the clock by four compressor systems of varying ages in a facility in Basle, Switzerland. The initial situation is analysed and the potential for making savings is estimated. Various possibilities for improvement are considered including changing the topology of the compressed-air network, the replacement of certain compressors and a new control system. Appropriate measures are proposed and compared with new installations.

  18. Optimised intake stroke analysis for flat and dome head pistons ...

    African Journals Online (AJOL)

    Optimised intake stroke analysis for flat and dome head pistons. ... in understanding the performance characteristics optioned between flat head and dome head pistons in engine design. ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  19. Energy-optimised mini-refrigerators; Energieoptimierter Minikuehlschrank. Massnahmen zur Optimierung der Energieeffizienz von Minikuehlschraenken

    Energy Technology Data Exchange (ETDEWEB)

    Burri, A.

    2007-10-15

    This illustrated final report for the Swiss Federal Office of Energy (SFOE) takes a look at measures to be taken to optimise the energy-efficiency of small refrigerators. Such devices are typically to be found in hotel rooms and on boats as well as in caravans and motor homes. The majority of these mini-refrigerators use the absorption principle for cooling. Although less efficient than their compressor-driven counterparts, absorption refrigerators satisfy market requirements and customer wishes with regard to noiseless and maintenance-free operation. The report discusses how optimisation of the absorption principle could lead to energy savings in the long term. The operating principles and energy balances of such refrigerators are discussed and a market overview is presented. Energy consumption of the refrigerators, possible savings and energy costs are discussed. The advantages and disadvantages of various cooling systems are examined as are further possibilities for making savings such as the optimisation of sizing, installation methods, airflow factors and operating temperatures.

  20. Optimisation of process parameters on thin shell part using response surface methodology (RSM)

    Science.gov (United States)

    Faiz, J. M.; Shayfull, Z.; Nasir, S. M.; Fathullah, M.; Rashidi, M. M.

    2017-09-01

    This study is carried out to focus on optimisation of process parameters by simulation using Autodesk Moldflow Insight (AMI) software. The process parameters are taken as the input in order to analyse the warpage value which is the output in this study. There are some significant parameters that have been used which are melt temperature, mould temperature, packing pressure, and cooling time. A plastic part made of Polypropylene (PP) has been selected as the study part. Optimisation of process parameters is applied in Design Expert software with the aim to minimise the obtained warpage value. Response Surface Methodology (RSM) has been applied in this study together with Analysis of Variance (ANOVA) in order to investigate the interactions between parameters that are significant to the warpage value. Thus, the optimised warpage value can be obtained using the model designed using RSM due to its minimum error value. This study comes out with the warpage value improved by using RSM.

  1. Preconditioned stochastic gradient descent optimisation for monomodal image registration

    NARCIS (Netherlands)

    Klein, S.; Staring, M.; Andersson, J.P.; Pluim, J.P.W.; Fichtinger, G.; Martel, A.; Peters, T.

    2011-01-01

    We present a stochastic optimisation method for intensity-based monomodal image registration. The method is based on a Robbins-Monro stochastic gradient descent method with adaptive step size estimation, and adds a preconditioning matrix. The derivation of the pre-conditioner is based on the

  2. Topology optimisation of micro fluidic mixers considering fluid-structure interactions with a coupled Lattice Boltzmann algorithm

    Science.gov (United States)

    Munk, David J.; Kipouros, Timoleon; Vio, Gareth A.; Steven, Grant P.; Parks, Geoffrey T.

    2017-11-01

    Recently, the study of micro fluidic devices has gained much interest in various fields from biology to engineering. In the constant development cycle, the need to optimise the topology of the interior of these devices, where there are two or more optimality criteria, is always present. In this work, twin physical situations, whereby optimal fluid mixing in the form of vorticity maximisation is accompanied by the requirement that the casing in which the mixing takes place has the best structural performance in terms of the greatest specific stiffness, are considered. In the steady state of mixing this also means that the stresses in the casing are as uniform as possible, thus giving a desired operating life with minimum weight. The ultimate aim of this research is to couple two key disciplines, fluids and structures, into a topology optimisation framework, which shows fast convergence for multidisciplinary optimisation problems. This is achieved by developing a bi-directional evolutionary structural optimisation algorithm that is directly coupled to the Lattice Boltzmann method, used for simulating the flow in the micro fluidic device, for the objectives of minimum compliance and maximum vorticity. The needs for the exploration of larger design spaces and to produce innovative designs make meta-heuristic algorithms, such as genetic algorithms, particle swarms and Tabu Searches, less efficient for this task. The multidisciplinary topology optimisation framework presented in this article is shown to increase the stiffness of the structure from the datum case and produce physically acceptable designs. Furthermore, the topology optimisation method outperforms a Tabu Search algorithm in designing the baffle to maximise the mixing of the two fluids.

  3. Code assessment and modelling for Design Basis Accident analysis of the European Sodium Fast Reactor design. Part II: Optimised core and representative transients analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lazaro, A., E-mail: aulach@iqn.upv.es [JRC-IET European Commission, Westerduinweg 3, PO BOX 2, 1755 ZG Petten (Netherlands); Schikorr, M. [KIT, Institute for Neutron Physics and Reactor Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Mikityuk, K. [PSI, Paul Scherrer Institut, 5232 Villigen (Switzerland); Ammirabile, L. [JRC-IET European Commission, Westerduinweg 3, PO BOX 2, 1755 ZG Petten (Netherlands); Bandini, G. [ENEA, Via Martiri di Monte Sole 4, 40129 Bologna (Italy); Darmet, G.; Schmitt, D. [EDF, 1 Avenue du Général de Gaulle, 92141 Clamart (France); Dufour, Ph.; Tosello, A. [CEA, St. Paul lez Durance, 13108 Cadarache (France); Gallego, E.; Jimenez, G. [UPM, José Gutiérrez Abascal, 2, 28006 Madrid (Spain); Bubelis, E.; Ponomarev, A.; Kruessmann, R.; Struwe, D. [KIT, Institute for Neutron Physics and Reactor Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Stempniewicz, M. [NRG, Utrechtseweg 310, P.O. Box-9034, 6800 ES Arnhem (Netherlands)

    2014-10-01

    Highlights: • Benchmarked models have been applied for the analysis of DBA transients of the ESFR design. • Two system codes are able to simulate the behavior of the system beyond sodium boiling. • The optimization of the core design and its influence in the transients’ evolution is described. • The analysis has identified peak values and grace times for the protection system design. - Abstract: The new reactor concepts proposed in the Generation IV International Forum require the development and validation of computational tools able to assess their safety performance. In the first part of this paper the models of the ESFR design developed by several organisations in the framework of the CP-ESFR project were presented and their reliability validated via a benchmarking exercise. This second part of the paper includes the application of those tools for the analysis of design basis accident (DBC) scenarios of the reference design. Further, this paper also introduces the main features of the core optimisation process carried out within the project with the objective to enhance the core safety performance through the reduction of the positive coolant density reactivity effect. The influence of this optimised core design on the reactor safety performance during the previously analysed transients is also discussed. The conclusion provides an overview of the work performed by the partners involved in the project towards the development and enhancement of computational tools specifically tailored to the evaluation of the safety performance of the Generation IV innovative nuclear reactor designs.

  4. Code assessment and modelling for Design Basis Accident analysis of the European Sodium Fast Reactor design. Part II: Optimised core and representative transients analysis

    International Nuclear Information System (INIS)

    Lazaro, A.; Schikorr, M.; Mikityuk, K.; Ammirabile, L.; Bandini, G.; Darmet, G.; Schmitt, D.; Dufour, Ph.; Tosello, A.; Gallego, E.; Jimenez, G.; Bubelis, E.; Ponomarev, A.; Kruessmann, R.; Struwe, D.; Stempniewicz, M.

    2014-01-01

    Highlights: • Benchmarked models have been applied for the analysis of DBA transients of the ESFR design. • Two system codes are able to simulate the behavior of the system beyond sodium boiling. • The optimization of the core design and its influence in the transients’ evolution is described. • The analysis has identified peak values and grace times for the protection system design. - Abstract: The new reactor concepts proposed in the Generation IV International Forum require the development and validation of computational tools able to assess their safety performance. In the first part of this paper the models of the ESFR design developed by several organisations in the framework of the CP-ESFR project were presented and their reliability validated via a benchmarking exercise. This second part of the paper includes the application of those tools for the analysis of design basis accident (DBC) scenarios of the reference design. Further, this paper also introduces the main features of the core optimisation process carried out within the project with the objective to enhance the core safety performance through the reduction of the positive coolant density reactivity effect. The influence of this optimised core design on the reactor safety performance during the previously analysed transients is also discussed. The conclusion provides an overview of the work performed by the partners involved in the project towards the development and enhancement of computational tools specifically tailored to the evaluation of the safety performance of the Generation IV innovative nuclear reactor designs

  5. Optimising trans-national power generation and transmission investments: a Southern African example

    International Nuclear Information System (INIS)

    Graeber, Bernhard; Spalding-Fecher, Randall; Gonah, Brian

    2005-01-01

    Increased integration and co-operation within the Southern African power sector has opened up significant opportunities for reducing the economic and environmental costs of meeting increasing electricity demand in Southern Africa. This paper applies a linear programming model to investigate the economic and environmental benefits of regional integrated planning for electricity, and the impact of including environmental costs in the decision-making process. We find that, from a financial perspective, optimising generation and transmission investments in the region would result in savings of dollar 2-4 billion over 20 years, or 5% of total system costs. Introducing a tax based on the external damage costs of carbon dioxide as part of the decision-making process would result in moderate increases in financial costs (15-20%), but would reduce regional carbon emissions by up to 55% at a mitigation cost of dollar 11 per tonne of carbon dioxide. This raises the possibility of financing regional power projects with Clean Development Mechanism funding, which we explore with an example

  6. Optimising a fall out dust monitoring sampling programme at a ...

    African Journals Online (AJOL)

    GREG

    Key words: Fall out dust monitoring, cement plant, optimising, air pollution sampling, fall out dust sampler locations. .... applied for those areas where controls are in place. Sampling ..... mass balance in the total cement manufacturing process.

  7. Optimisation of oxygen ion transport in materials for ceramic membrane devices.

    Science.gov (United States)

    Kilner, J A

    2007-01-01

    Oxygen transport in ceramic oxide materials has received much attention over the past few decades. Much of this interest has stemmed from the desire to construct high temperature electrochemical devices for energy conversion, an example being the solid oxide fuel cell. In order to achieve high performance for these devices, insights are needed in how to achieve optimum performance from the functional components such as the electrolytes and electrodes. This includes the optimisation of oxygen transport through the crystal lattice of electrode and electrolyte materials and across the homogeneous (grain boundary) and heterogeneous interfaces that exist in real devices. Strategies are discussed for the optimisation of these quantities and current problems in the characterisation of interfacial transport are explored.

  8. 1st oPAC Topical Workshop: Grand Challenges in Accelerator Optimisation

    CERN Document Server

    2013-01-01

    Accelerators are key instruments for fundamental research, health and industry applications. International collaboration is very important for their continued optimisation. To address this oPAC is organising this two-day international workshop on Grand Challenges in Accelerator Optimisation. The workshop will provide an overview of the current state of the art in beam physics, numerical simulations and beam instrumentation and highlight existing limitations. It will discuss research and development being undertaken and ambitions to further improve the performance of existing and future facilities. In addition to invited talks, there will be industry displays and a special seminar covering recent LHC discoveries. All participants will have an opportunity to contribute a poster.

  9. The optimisation principle and the new ICRP recommendations: practical implications on operational radiation protection

    International Nuclear Information System (INIS)

    Lochard, J.

    1992-01-01

    The formulation of the optimisation principle proposed by the International Commission of Radiological Protection in its new recommendations is largely oriented towards better control of individual doses. In this perspective, the concept of doe constraint and the reference to equity in dose distributions are becoming key elements within the optimisation process. This paper discusses some first reflexions regarding this new orientation and outlines the main impacts that must be forwarded to the practical level. (author)

  10. Contribution à l'optimisation de la conduite des procédés alimentaires

    OpenAIRE

    Olmos-Perez , Alejandra

    2003-01-01

    The main objective of this work is the development of a methodology to calculate the optimal operating conditions applicable in food processes control. In the first part of this work, we developed an optimization strategy in two stages. Firstly, the optimisation problem is constructed. Afterwards, a feasible optimisation method is chosen to solve the problem. This choice is made through a decisional diagram, which proposes a deterministic (sequential quadratic programming, SQP), a stochastic ...

  11. Standardised approach to optimisation

    International Nuclear Information System (INIS)

    Warren-Forward, Helen M.; Beckhaus, Ronald

    2004-01-01

    Optimisation of radiographic images is said to have been obtained if the patient has achieved an acceptable level of dose and the image is of diagnostic value. In the near future, it will probably be recommended that radiographers measure patient doses and compare them to reference levels. The aim of this paper is to describe a standardised approach to optimisation of radiographic examinations in a diagnostic imaging department. A three-step approach is outlined with specific examples for some common examinations (chest, abdomen, pelvis and lumbar spine series). Step One: Patient doses are calculated. Step Two: Doses are compared to existing reference levels and the technique used compared to image quality criteria. Step Three: Appropriate action is taken if doses are above the reference level. Results: Average entrance surface doses for two rooms were as follows AP Abdomen (6.3mGy and 3.4mGy); AP Lumbar Spine (6.4mGy and 4.1mGy) for AP Pelvis (4.8mGy and 2.6mGy) and PA chest (0.19mGy and 0.20mGy). Comparison with the Commission of the European Communities (CEC) recommended techniques identified large differences in the applied potential. The kVp values in this study were significantly lower (by up to lOkVp) than the CEC recommendations. The results of this study have indicated that there is a need to monitor radiation doses received by patients undergoing diagnostic radiography examinations. Not only has the assessment allowed valuable comparison with International Diagnostic Reference Levels and Radiography Good Practice but has demonstrated large variations in mean doses being delivered from different rooms of the same radiology department. Following the simple 3-step approach advocated in this paper should either provide evidence that department are practising the ALARA principle or assist in making suitable changes to current practice. Copyright (2004) Australian Institute of Radiography

  12. A Synchronous-Asynchronous Particle Swarm Optimisation Algorithm

    Science.gov (United States)

    Ab Aziz, Nor Azlina; Mubin, Marizan; Mohamad, Mohd Saberi; Ab Aziz, Kamarulzaman

    2014-01-01

    In the original particle swarm optimisation (PSO) algorithm, the particles' velocities and positions are updated after the whole swarm performance is evaluated. This algorithm is also known as synchronous PSO (S-PSO). The strength of this update method is in the exploitation of the information. Asynchronous update PSO (A-PSO) has been proposed as an alternative to S-PSO. A particle in A-PSO updates its velocity and position as soon as its own performance has been evaluated. Hence, particles are updated using partial information, leading to stronger exploration. In this paper, we attempt to improve PSO by merging both update methods to utilise the strengths of both methods. The proposed synchronous-asynchronous PSO (SA-PSO) algorithm divides the particles into smaller groups. The best member of a group and the swarm's best are chosen to lead the search. Members within a group are updated synchronously, while the groups themselves are asynchronously updated. Five well-known unimodal functions, four multimodal functions, and a real world optimisation problem are used to study the performance of SA-PSO, which is compared with the performances of S-PSO and A-PSO. The results are statistically analysed and show that the proposed SA-PSO has performed consistently well. PMID:25121109

  13. The bases for optimisation of scheduled repairs and tests of safety systems to improve the NPP productive efficiency

    International Nuclear Information System (INIS)

    Bilej, D.V.; Vasil'chenko, S.V.; Vlasenko, N.I.; Vasil'chenko, V.N.; Skalozubov, V.I.

    2004-01-01

    In the frames of risk-informed approaches the paper proposed the theoretical bases for methods of optimisation of scheduled repairs and tests of safety systems at nuclear power plants. The optimisation criterion is the objective risk function minimising. This function depends on the scheduled repairs/tests periodicity and the allowed time to bring the system channel to a state of non-operability. The main optimisation direct is to reduce the repair time with the purpose of enhancement of productive efficiency

  14. Comparing and Optimising Parallel Haskell Implementations for Multicore Machines

    DEFF Research Database (Denmark)

    Berthold, Jost; Marlow, Simon; Hammond, Kevin

    2009-01-01

    In this paper, we investigate the differences and tradeoffs imposed by two parallel Haskell dialects running on multicore machines. GpH and Eden are both constructed using the highly-optimising sequential GHC compiler, and share thread scheduling, and other elements, from a common code base. The ...

  15. Optimisation of Hidden Markov Model using Baum–Welch algorithm

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Earth System Science; Volume 126; Issue 1. Optimisation of Hidden Markov Model using Baum–Welch algorithm for prediction of maximum and minimum temperature over Indian Himalaya. J C Joshi Tankeshwar Kumar Sunita Srivastava Divya Sachdeva. Volume 126 Issue 1 February 2017 ...

  16. Design and manufacture of Portland cement - application of sensitivity analysis in exploration and optimisation Part II. Optimisation

    DEFF Research Database (Denmark)

    Svinning, K.; Høskuldsson, Agnar

    2006-01-01

    A program for a model-based optimisation has been developed. The program contains two subprograms. The first one does minimising or maximising constrained by one original PLS-component or one equal to a combination of several. The second one does searching for the optimal combination of PLS-compo......-components, which gives max or min y. The program has proved to be applicable for achieving realistic results for implementation in the design of Portland cement with respect to performance and in the quality control during production....

  17. Solar photo-Fenton optimisation in treating carbofuran-contaminated water

    Directory of Open Access Journals (Sweden)

    Manuel Alejandro Hernández-Shek

    2012-01-01

    Full Text Available Box-Benkhen design response-surface methodology was developed to optimise photo-Fenton degradation of carbofuran (C12H15NO3 by using a compound parabolic collector pilot plant. The four variables considered in Box-Benkhen design model included carbofuran degradation percentage, initial carbofuran concentration, hydrogen peroxide [H2O2] concentration and iron [Fe2+] concentration. Degradation was monitored by using total organic carbon concentration and high-performance liquid chromatography. A 93.2 mg l-1 carbofuran concentration was completely degraded in t30W = 15 min with 17.1 mg l-1 Fe2+ and 121.6 mg l-1 H2O2. Photo-Fenton degradation led to 76.7% mineralisation. Biodegradability during optimisation was evaluated by using the BOD5/COD ratio; this value increased from 0.04 at the beginning of the process to 0.52 in t30W = 20 min, thereby showing the effectiveness of using biological treatments.

  18. Water distribution systems design optimisation using metaheuristics and hyperheuristics

    Directory of Open Access Journals (Sweden)

    DN Raad

    2011-06-01

    Full Text Available The topic of multi-objective water distribution systems (WDS design optimisation using metaheuristics is investigated, comparing numerous modern metaheuristics, including sev- eral multi-objective evolutionary algorithms, an estimation of distribution algorithm and a recent hyperheuristic named AMALGAM (an evolutionary framework for the simultaneous incorporation of multiple metaheuristics, in order to determine which approach is most capa- ble with respect to WDS design optimisation. Novel metaheuristics and variants of existing algorithms are developed, for a total of twenty-three algorithms examined. Testing with re- spect to eight small-to-large-sized WDS benchmarks from the literature reveal that the four top-performing algorithms are mutually non-dominated with respect to the various perfor- mance metrics used. These algorithms are NSGA-II, TAMALGAMJndu , TAMALGAMndu and AMALGAMSndp (the last three being novel variants of AMALGAM. However, when these four algorithms are applied to the design of a very large real-world benchmark, the AMALGAM paradigm outperforms NSGA-II convincingly, with AMALGAMSndp exhibiting the best performance overall.

  19. Computed tomography dose optimisation in cystic fibrosis: A review.

    LENUS (Irish Health Repository)

    Ferris, Helena

    2016-04-28

    Cystic fibrosis (CF) is the most common autosomal recessive disease of the Caucasian population worldwide, with respiratory disease remaining the most relevant source of morbidity and mortality. Computed tomography (CT) is frequently used for monitoring disease complications and progression. Over the last fifteen years there has been a six-fold increase in the use of CT, which has lead to a growing concern in relation to cumulative radiation exposure. The challenge to the medical profession is to identify dose reduction strategies that meet acceptable image quality, but fulfil the requirements of a diagnostic quality CT. Dose-optimisation, particularly in CT, is essential as it reduces the chances of patients receiving cumulative radiation doses in excess of 100 mSv, a dose deemed significant by the United Nations Scientific Committee on the Effects of Atomic Radiation. This review article explores the current trends in imaging in CF with particular emphasis on new developments in dose optimisation.

  20. Application of the principles of justification and optimisation to products causing public exposure

    International Nuclear Information System (INIS)

    Fleishman, A.B.; Wrixon, A.D.

    1980-01-01

    The purpose of this paper is to explore the practical incorporation of the ICRP principles of justification and optimisation into a policy designed to control radioactive consumer products. ICRP recommends the use of cost benefit analysis and differential cost benefit analysis for justification and optimisation respectively, and expresses these procedures in simple mathematical forms. This might suggest that their application should involve quantification and therefore be objective. The problems which arise in such quantification are discussed. These include the derivation of a market demand curve for a given product and its adjustment to remove any distortion of perceived value or risk produced by advertising; the costing of detriment to those who receive no benefit (e.g., as a consequence of uncontrolled disposal); and the costs of the analyses themselves. Furthermore, both cost benefit and differential cost benefit analyses are dependent on availability of market and performance data. This is incompatible with prior approval schemes in which a decision must be made before the product is distributed. Ultimately criteria for product justification must therefore be based on judgements on the acceptability of risk that are political rather than scientific in nature. Optimisation must initially be carried out on an intuitive basis. However as experience is gained with similar products the opportunity for more formal optimisation and the setting of radiological protection standards arise. This requires further value judgements which are illustrated with reference to examples. (author)

  1. Linac design for intense hadron beams

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Chuan

    2009-12-14

    , no beam losses were observed and all emittance growths were well under control. To solve the well-known transition problems between two kinds of different accelerating structures, some matching techniques have been developed and applied for the RFQ accelerator and the KONUS-based H-type DTL with the following idea: to perform the RFQ-DTL matching inside the RFQ, and not in the MEBT, because the continuous, velocity-independent electric focusing is very efficient for a low-{beta} beam. For the FRANZ project, the output longitudinal particle distribution has been rotated by the so-called Longitudinal-Rotation Technique, which can narrow the phase spread of the beam to fit into the acceptance of a KONUS structure. For the EUROTRANS injector, the matching has been done in the transverse planes: two additional transition cells at the end of the RFQ were introduced to turn both output transverse emittance ellipses axial-symmetric and into the same orientation, which helped leading to similar transverse beam developments in the DTL part. In addition, the error study is another important topic of this dissertation. In the design study, usually only ideal operation conditions and perfect accelerator components have been taken into account. According to the capabilities of the simulation codes, seven kinds of RFQ errors and four kinds of DTL errors have been applied to the designed FRANZ RFQ and IFMIF DTL machines, respectively. For the EUROTRANS injector, combined RFQ and DTL errors were used. (orig.)

  2. Linac design for intense hadron beams

    International Nuclear Information System (INIS)

    Zhang, Chuan

    2009-01-01

    losses were observed and all emittance growths were well under control. To solve the well-known transition problems between two kinds of different accelerating structures, some matching techniques have been developed and applied for the RFQ accelerator and the KONUS-based H-type DTL with the following idea: to perform the RFQ-DTL matching inside the RFQ, and not in the MEBT, because the continuous, velocity-independent electric focusing is very efficient for a low-β beam. For the FRANZ project, the output longitudinal particle distribution has been rotated by the so-called Longitudinal-Rotation Technique, which can narrow the phase spread of the beam to fit into the acceptance of a KONUS structure. For the EUROTRANS injector, the matching has been done in the transverse planes: two additional transition cells at the end of the RFQ were introduced to turn both output transverse emittance ellipses axial-symmetric and into the same orientation, which helped leading to similar transverse beam developments in the DTL part. In addition, the error study is another important topic of this dissertation. In the design study, usually only ideal operation conditions and perfect accelerator components have been taken into account. According to the capabilities of the simulation codes, seven kinds of RFQ errors and four kinds of DTL errors have been applied to the designed FRANZ RFQ and IFMIF DTL machines, respectively. For the EUROTRANS injector, combined RFQ and DTL errors were used. (orig.)

  3. An exergy-based multi-objective optimisation model for energy retrofit strategies in non-domestic buildings

    International Nuclear Information System (INIS)

    García Kerdan, Iván; Raslan, Rokia; Ruyssevelt, Paul

    2016-01-01

    While the building sector has a significant thermodynamic improvement potential, exergy analysis has been shown to provide new insight for the optimisation of building energy systems. This paper presents an exergy-based multi-objective optimisation tool that aims to assess the impact of a diverse range of retrofit measures with a focus on non-domestic buildings. EnergyPlus was used as a dynamic calculation engine for first law analysis, while a Python add-on was developed to link dynamic exergy analysis and a Genetic Algorithm optimisation process with the aforementioned software. Two UK archetype case studies (an office and a primary school) were used to test the feasibility of the proposed framework. Different measures combinations based on retrofitting the envelope insulation levels and the application of different HVAC configurations were assessed. The objective functions in this study are annual energy use, occupants' thermal comfort, and total building exergy destructions. A large range of optimal solutions was achieved highlighting the framework capabilities. The model achieved improvements of 53% in annual energy use, 51% of exergy destructions and 66% of thermal comfort for the school building, and 50%, 33%, and 80% for the office building. This approach can be extended by using exergoeconomic optimisation. - Highlights: • Integration of dynamic exergy analysis into a retrofit-oriented simulation tool. • Two UK non-domestic building archetypes are used as case studies. • The model delivers non-dominated solutions based on energy, exergy and comfort. • Exergy destructions of ERMs are optimised using GA algorithms. • Strengths and limitations of the proposed exergy-based framework are discussed.

  4. Topology Optimisation for Coupled Convection Problems

    DEFF Research Database (Denmark)

    Alexandersen, Joe; Andreasen, Casper Schousboe; Aage, Niels

    stabilised finite elements implemented in a parallel multiphysics analysis and optimisation framework DFEM [1], developed and maintained in house. Focus is put on control of the temperature field within the solid structure and the problems can therefore be seen as conjugate heat transfer problems, where heat...... conduction governs in the solid parts of the design domain and couples to convection-dominated heat transfer to a surrounding fluid. Both loosely coupled and tightly coupled problems are considered. The loosely coupled problems are convection-diffusion problems, based on an advective velocity field from...

  5. Do existing research reactors teach us all about beam tube optimisation?

    International Nuclear Information System (INIS)

    Roegler, Hans-Joachim; Feltes, Wolfgang

    1998-01-01

    The contribution makes the attempt to analyse the data base available in the literature and in Siemens' own projects and to find out potential systematics from the existing research reactors with beam tubes, separated into reactors with different reflectors and distinguished for tangential and radial tubes and cold neutron sources, respectively some generic calculations serve as gauging data. The contribution is not meant as critics on any design. The results might serve supporting designers and operators when evaluating the pros and cons of existing or planned design in terms of the optimum beam tubes. Existing lacks of systematics are evaluated in view of suitable explanations and constraints, which do not allow optimisation. Examples of such constraints are the different material layers between fuel zone and reflector zone which have various reasons. The limited data in the literature plus the numerous lacks of precision of the representation of those data should be an incentive to improve the performed analysis by collecting more exact data and re-doing the evaluation before answering the title question really

  6. Design optimisation of a flywheel hybrid vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Kok, D.B.

    1999-11-04

    This thesis describes the design optimisation of a flywheel hybrid vehicle with respect to fuel consumption and exhaust gas emissions. The driveline of this passenger car uses two power sources: a small spark ignition internal combustion engine with three-way catalyst, and a highspeed flywheel system for kinetic energy storage. A custom-made continuously variable transmission (CVT) with so-called i{sup 2} control transports energy between these power sources and the vehicle wheels. The driveline includes auxiliary systems for hydraulic, vacuum and electric purposes. In this fully mechanical driveline, parasitic energy losses determine the vehicle's fuel saving potential to a large extent. Practicable energy loss models have been derived to quantify friction losses in bearings, gearwheels, the CVT, clutches and dynamic seals. In addition, the aerodynamic drag in the flywheel system and power consumption of auxiliaries are charted. With the energy loss models available, a calculation procedure is introduced to optimise the flywheel as a subsystem in which the rotor geometry, the safety containment, and the vacuum system are designed for minimum energy use within the context of automotive applications. A first prototype of the flywheel system was tested experimentally and subsequently redesigned to improve rotordynamics and safety aspects. Coast-down experiments with the improved version show that the energy losses have been lowered significantly. The use of a kinetic energy storage device enables the uncoupling of vehicle wheel power and engine power. Therefore, the engine can be smaller and it can be chosen to operate in its region of best efficiency in start-stop mode. On a test-rig, the measured engine fuel consumption was reduced with more than 30 percent when the engine is intermittently restarted with the aid of the flywheel system. Although the start-stop mode proves to be advantageous for fuel consumption, exhaust gas emissions increase temporarily

  7. Numerical optimisation of an axial turbine; Numerische Optimierung einer Axialturbine

    Energy Technology Data Exchange (ETDEWEB)

    Welzel, B.

    1998-12-31

    The author presents a method for automatic shape optimisation of components with internal or external flow. The method combines a program for numerical calculation of frictional turbulent flow with an optimisation algorithm. Algorithms are a simplex search strategy and an evolution strategy. The shape of the component to be optimized is variable due to shape parameters modified by the algorithm. For each shape, a flow calculation is carried out on whose basis a functional value like performance, loss, lift or resistivity is calculated. For validation, the optimisation method is used in simple examples with known solutions. It is applied. It is applied to the components of a slow-running axial turbine. Components with accelerated and delayed rotationally symmetric flow and 2D blade profiles are optimized. [Deutsch] Es wird eine Methode zur automatischen Formoptimierung durchstroemter oder umstroemter Bauteile vorgestellt. Diese koppelt ein Programm zur numerischen Berechnung reibungsbehafteter turbulenter Stroemungen mit einem Optimierungsalgorithmus. Dabei kommen als Algorithmen eine Simplex-Suchstrategie und eine Evolutionsstrategie zum Einsatz. Die Form des zu optimierenden Koerpers ist durch Formparameter, die vom Algorithmus veraendert werden, variabel. Fuer jede Form wird eine Stroemungsberechnung durchgefuehrt und mit dieser ein Funktionswert wie Wirkungsgrad, Verlust, Auftrieb oder Widerstandskraft berechnet. Die Optimierungsmethode wird zur Validierung in einfachen Beispielen mit bekannter Loesung eingesetzt. Zur Anwendung kommt sie in den einzelnen Komponenten einer langsamlaeufigen Axialturbine. Es werden Bauteile mit beschleunigter und verzoegerter rotationssymmetrischer Stroemung und 2D-Schaufelprofile optimiert. (orig.)

  8. Analysing the performance of dynamic multi-objective optimisation algorithms

    CSIR Research Space (South Africa)

    Helbig, M

    2013-06-01

    Full Text Available and the goal of the algorithm is to track a set of tradeoff solutions over time. Analysing the performance of a dynamic multi-objective optimisation algorithm (DMOA) is not a trivial task. For each environment (before a change occurs) the DMOA has to find a set...

  9. A MILP for multi-machine injection moulding sequencing in the scope of C2NET Project

    Directory of Open Access Journals (Sweden)

    Beatriz Andrés

    2018-01-01

    Full Text Available The goal of C2NET European H2020 Funded Project is the creation of cloud-enabled tools for supporting the SMEs supply network optimization of manufacturing and logistic assets based on collaborative demand, production and delivery plans. In the scope of C2NET Project, and particularly in the Optimisation module (C2NET OPT, this paper proposes a novel holistic mixed integer linear programing (MILP model to optimise the injection sequencing in a multi-machine case. The results of the MILP will support the production planner decision-making process in the calculation of (i moulds setup in certain machines, and (ii the amount of products to produce in order to minimise the setup, inventory, and backorders costs. The designed MILP takes part of the algorithms repository created in C2NET European Funded Project to solve realistic industry planning problems. The MILP is verified in realistic data considering three data sets with different sizes, in order to test it’s the computation efficiency.

  10. Reliability analysis and optimisation of subsea compression system facing operational covariate stresses

    International Nuclear Information System (INIS)

    Okaro, Ikenna Anthony; Tao, Longbin

    2016-01-01

    This paper proposes an enhanced Weibull-Corrosion Covariate model for reliability assessment of a system facing operational stresses. The newly developed model is applied to a Subsea Gas Compression System planned for offshore West Africa to predict its reliability index. System technical failure was modelled by developing a Weibull failure model incorporating a physically tested corrosion profile as stress in order to quantify the survival rate of the system under additional operational covariates including marine pH, temperature and pressure. Using Reliability Block Diagrams and enhanced Fusell-Vesely formulations, the whole system was systematically decomposed to sub-systems to analyse the criticality of each component and optimise them. Human reliability was addressed using an enhanced barrier weighting method. A rapid degradation curve is obtained on a subsea system relative to the base case subjected to a time-dependent corrosion stress factor. It reveals that subsea system components failed faster than their Mean time to failure specifications from Offshore Reliability Database as a result of cumulative marine stresses exertion. The case study demonstrated that the reliability of a subsea system can be systematically optimised by modelling the system under higher technical and organisational stresses, prioritising the critical sub-systems and making befitting provisions for redundancy and tolerances. - Highlights: • Novel Weibull Corrosion-Covariate model for reliability analysis of subsea assets. • Predict the accelerated degradation profile of a subsea gas compression. • An enhanced optimisation method based on Fusell-Vesely decomposition process. • New optimisation approach for smoothening of over- and under-designed components. • Demonstrated a significant improvement in producing more realistic failure rate.

  11. A comparison of an energy/economic-based against an exergoeconomic-based multi-objective optimisation for low carbon building energy design

    International Nuclear Information System (INIS)

    García Kerdan, Iván; Raslan, Rokia; Ruyssevelt, Paul; Morillón Gálvez, David

    2017-01-01

    This study presents a comparison of the optimisation of building energy retrofit strategies from two different perspectives: an energy/economic-based analysis and an exergy/exergoeconomic-based analysis. A recently retrofitted community centre is used as a case study. ExRET-Opt, a novel building energy/exergy simulation tool with multi-objective optimisation capabilities based on NSGA-II is used to run both analysis. The first analysis, based on the 1st Law only, simultaneously optimises building energy use and design's Net Present Value (NPV). The second analysis, based on the 1st and the 2nd Laws, simultaneously optimises exergy destructions and the exergoeconomic cost-benefit index. Occupant thermal comfort is considered as a common objective function for both approaches. The aim is to assess the difference between the methods and calculate the performance among main indicators, considering the same decision variables and constraints. Outputs show that the inclusion of exergy/exergoeconomics as objective functions into the optimisation procedure has resulted in similar 1st Law and thermal comfort outputs, while providing solutions with less environmental impact under similar capital investments. This outputs demonstrate how the 1st Law is only a necessary calculation while the utilisation of the 1st and 2nd Laws becomes a sufficient condition for the analysis and design of low carbon buildings. - Highlights: • The study compares an energy-based and an exergy-based building design optimisation. • Occupant thermal comfort is considered as a common objective function. • A comparison of thermodynamic outputs is made against the actual retrofit design. • Under similar constraints, second law optimisation presents better overall results. • Exergoeconomic optimisation solutions improves building exergy efficiency to double.

  12. Biofuels carbon footprints: Whole-systems optimisation for GHG emissions reduction.

    Science.gov (United States)

    Zamboni, Andrea; Murphy, Richard J; Woods, Jeremy; Bezzo, Fabrizio; Shah, Nilay

    2011-08-01

    A modelling approach for strategic design of ethanol production systems combining lifecycle analysis (LCA) and supply chain optimisation (SCO) can significantly contribute to assess their economic and environmental sustainability and to guide decision makers towards a more conscious implementation of ad hoc farming and processing practices. Most models applications so far have been descriptive in nature; the model proposed in this work is "normative" in that it aims to guide actions towards optimal outcomes (e.g. optimising the nitrogen balance through the whole supply chain). The modelling framework was conceived to steer strategic policies through a geographically specific design process considering economic and environmental criteria. Results shows how a crop management strategy devised from a whole systems perspective can significantly contribute to mitigate global warming even in first generation technologies. Copyright © 2011 Elsevier Ltd. All rights reserved.

  13. An optimised portfolio management model, incorporating best practices

    OpenAIRE

    2015-01-01

    M.Ing. (Engineering Management) Driving sustainability, optimising return on investments and cultivating a competitive market advantage, are imperative for organisational success and growth. In order to achieve the business objectives and value proposition, effective management strategies must be efficiently implemented, monitored and controlled. Failure to do so ultimately result in; financial loss due to increased capital and operational expenditure, schedule slippages, substandard deliv...

  14. Statistical meandering wake model and its application to yaw-angle optimisation of wind farms

    DEFF Research Database (Denmark)

    Thøgersen, Emil; Tranberg, Bo; Herp, Jürgen

    2017-01-01

    deterministic models to a statistical meandering wake model (SMWM), where a random directional deflection is assigned to a narrow wake in such a way that on average it resembles a broad Jensen wake. In a second step, the model is further generalised to wind-farm level, where the deflections of the multiple...... wakes are treated as independently and identically distributed random variables. When carefully calibrated to the Nysted wind farm, the ensemble average of the statistical model produces the same wind-direction dependence of the power efficiency as obtained from the standard Jensen model. Upon using...... the JWM to perform a yaw-angle optimisation of wind-farm power output, we find an optimisation gain of 6.7% for the Nysted wind farm when compared to zero yaw angles and averaged over all wind directions. When applying the obtained JWM-based optimised yaw angles to the SMWM, the ensemble-averaged gain...

  15. Strategic optimisation of microgrid by evolving a unitised regenerative fuel cell system operational criterion

    Science.gov (United States)

    Bhansali, Gaurav; Singh, Bhanu Pratap; Kumar, Rajesh

    2016-09-01

    In this paper, the problem of microgrid optimisation with storage has been addressed in an unaccounted way rather than confining it to loss minimisation. Unitised regenerative fuel cell (URFC) systems have been studied and employed in microgrids to store energy and feed it back into the system when required. A value function-dependent on line losses, URFC system operational cost and stored energy at the end of the day are defined here. The function is highly complex, nonlinear and multi dimensional in nature. Therefore, heuristic optimisation techniques in combination with load flow analysis are used here to resolve the network and time domain complexity related with the problem. Particle swarm optimisation with the forward/backward sweep algorithm ensures optimal operation of microgrid thereby minimising the operational cost of the microgrid. Results are shown and are found to be consistently improving with evolution of the solution strategy.

  16. Use of evidence-based practices in pregnancy and childbirth: South East Asia Optimising Reproductive and Child Health in Developing Countries project.

    Directory of Open Access Journals (Sweden)

    M Laopaiboon

    2008-07-01

    Full Text Available The burden of mortality and morbidity related to pregnancy and childbirth remains concentrated in developing countries. SEA-ORCHID (South East Asia Optimising Reproductive and Child Health In Developing countries is evaluating whether a multifaceted intervention to strengthen capacity for research synthesis, evidence-based care and knowledge implementation improves adoption of best clinical practice recommendations leading to better health for mothers and babies. In this study we assessed current practices in perinatal health care in four South East Asian countries and determined whether they were aligned with best practice recommendations.We completed an audit of 9550 medical records of women and their 9665 infants at nine hospitals; two in each of Indonesia, Malaysia and The Philippines, and three in Thailand between January-December 2005. We compared actual clinical practices with best practice recommendations selected from the Cochrane Library and the World Health Organization Reproductive Health Library. Evidence-based components of the active management of the third stage of labour and appropriately treating eclampsia with magnesium sulphate were universally practiced in all hospitals. Appropriate antibiotic prophylaxis for caesarean section, a beneficial form of care, was practiced in less than 5% of cases in most hospitals. Use of the unnecessary practices of enema in labour ranged from 1% to 61% and rates of episiotomy for vaginal birth ranged from 31% to 95%. Other appropriate practices were commonly performed to varying degrees between countries and also between hospitals within the same country.Whilst some perinatal health care practices audited were consistent with best available evidence, several were not. We conclude that recording of clinical practices should be an essential step to improve quality of care. Based on these findings, the SEA-ORCHID project team has been developing and implementing interventions aimed at increasing

  17. Optimisation of energy supply at off-grid healthcare facilities using Monte Carlo simulation

    International Nuclear Information System (INIS)

    Dufo-López, Rodolfo; Pérez-Cebollada, Eduardo; Bernal-Agustín, José L.; Martínez-Ruiz, Ignacio

    2016-01-01

    Highlights: • We study the application of renewable energies in a hospital located in Kalonge. • A stochastic approach is developed by means of Monte Carlo simulation. • We propose adding PV panels to improve the supply of electrical energy. • The results show that optimal design could achieve 28% reduction in the LCE. • Furthermore, we discuss possible improvements to the telecommunications of the hospital. - Abstract: In this paper, we present a methodology for the optimisation of off-grid hybrid systems (photovoltaic–diesel–battery systems). A stochastic approach is developed by means of Monte Carlo simulation to consider the uncertainties of irradiation and load. The optimisation is economic; that is, we look for a system with a lower net present cost including installation, replacement of the components, operation and maintenance, etc. The most important variable that must be estimated is the batteries lifespan, which depends on the operating conditions (charge/discharge cycles, corrosion, state of charge, etc.). Previous works used classical methods for the estimation of batteries lifespan, which can be too optimistic in many cases, obtaining a net present cost of the system much lower than in reality. In this work, we include an advanced weighted Ah-throughput model for the lead-acid batteries, which is much more realistic. The optimisation methodology presented in this paper is applied in the optimisation of the electrical supply for an off-grid hospital located in Kalonge (Democratic Republic of the Congo). At the moment, the power supply relies on a diesel generator; batteries are used in order to ensure the basic supply of energy when the generator is unavailable (night hours). The optimisation includes the possibility of adding solar photovoltaic (PV) panels to improve the supply of electrical energy. The results show that optimal design could achieve a 28% reduction in the levelised cost of energy and a 54% reduction in the diesel fuel

  18. Process integration of the new blast furnace - Project Prima. Final report; Processintegration av den nya masugnen - Projekt Prima. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Ryman, Christer; Niemi, Tommi [Metallurgical Research Inst. AB, Luleaa (Sweden); Larsson, Mikael [Luleaa Technical Univ. (Sweden); Gyllenram, Rutger [Kobolde and Partners AB, Stockholm (Sweden)

    2004-05-01

    An one-dimensional static blast furnace model consisting of a mass balance and a heat balance model with an user friendly web interface has been developed. The model can be used for process optimisation and to compare different operating modes, but can also be used as a sub model for total analysis of the production site by means of process integration. It is also possible to use the model for planning of trials at an industrial or an experimental, blast furnace. The project has been executed by MEFOS (BF model development), Kobolde and Partners AB (system development) and Luleaa University of Technology (system integration). This report contains a brief model description, discussion of possible sources of errors, and examples of optimisation calculations. The project has been active from 2001 to 2003.

  19. Optimising a Model of Minimum Stock Level Control and a Model of Standing Order Cycle in Selected Foundry Plant

    Directory of Open Access Journals (Sweden)

    Szymszal J.

    2013-09-01

    Full Text Available It has been found that the area where one can look for significant reserves in the procurement logistics is a rational management of the stock of raw materials. Currently, the main purpose of projects which increase the efficiency of inventory management is to rationalise all the activities in this area, taking into account and minimising at the same time the total inventory costs. The paper presents a method for optimising the inventory level of raw materials under a foundry plant conditions using two different control models. The first model is based on the estimate of an optimal level of the minimum emergency stock of raw materials, giving information about the need for an order to be placed immediately and about the optimal size of consignments ordered after the minimum emergency level has occurred. The second model is based on the estimate of a maximum inventory level of raw materials and an optimal order cycle. Optimisation of the presented models has been based on the previously done selection and use of rational methods for forecasting the time series of the delivery of a chosen auxiliary material (ceramic filters to a casting plant, including forecasting a mean size of the delivered batch of products and its standard deviation.

  20. Experimental Investigation and Taguchi Optimisation of Drilling Properties on Teak Wood Reinforced Epoxy Resin

    Science.gov (United States)

    Lilly Mercy, J.; Shaqir Tanvir, Mohamed; Swaroopkanth, K.

    2017-05-01

    The drilling properties of teak reinforced epoxy resin composite are explored in this work. The thrust force and temperature during the drilling process was found and optimised. Nine holes were drilled in accordance with L9 orthogonal array on Medium Density Fibre board and Teak wood reinforced epoxy composite board and the thrust force and temperature induced during drilling is measured. Drilling experiments were conducted using CNC Vertical drilling machine and the thrust force was measured using dynamometer and temperature using infra-red thermometer. The experiments were conducted with varying levels of spindle speed and feed rate and optimised using Taguchi optimisation. It was observed that higher thrust and temperature were observed while drilling teak wood composite due to the high mechanical strength of teak wood. The hard and brittle properties of the resin seemed to be more pronounced in the composite. The experimental results were optimised to find the best combination of input parameters for reduced thrust and temperature. When speed increases, thrust force decreases and temperature increases. When feed increases, thrust force increases and temperature decreases. Experimental findings encouragesto use teak wood reinforced epoxy resin as a substitute for the traditionally used Medium Density Fibre Board. The percentage of mixing of teak dust can be increased with various resin combinations to arrive at the best suitable combination for obtaining optimal mechanical properties.

  1. Statistical meandering wake model and its application to yaw-angle optimisation of wind farms

    International Nuclear Information System (INIS)

    Thøgersen, E; Tranberg, B; Greiner, M; Herp, J

    2017-01-01

    The wake produced by a wind turbine is dynamically meandering and of rather narrow nature. Only when looking at large time averages, the wake appears to be static and rather broad, and is then well described by simple engineering models like the Jensen wake model (JWM). We generalise the latter deterministic models to a statistical meandering wake model (SMWM), where a random directional deflection is assigned to a narrow wake in such a way that on average it resembles a broad Jensen wake. In a second step, the model is further generalised to wind-farm level, where the deflections of the multiple wakes are treated as independently and identically distributed random variables. When carefully calibrated to the Nysted wind farm, the ensemble average of the statistical model produces the same wind-direction dependence of the power efficiency as obtained from the standard Jensen model. Upon using the JWM to perform a yaw-angle optimisation of wind-farm power output, we find an optimisation gain of 6.7% for the Nysted wind farm when compared to zero yaw angles and averaged over all wind directions. When applying the obtained JWM-based optimised yaw angles to the SMWM, the ensemble-averaged gain is calculated to be 7.5%. This outcome indicates the possible operational robustness of an optimised yaw control for real-life wind farms. (paper)

  2. Statistical meandering wake model and its application to yaw-angle optimisation of wind farms

    Science.gov (United States)

    Thøgersen, E.; Tranberg, B.; Herp, J.; Greiner, M.

    2017-05-01

    The wake produced by a wind turbine is dynamically meandering and of rather narrow nature. Only when looking at large time averages, the wake appears to be static and rather broad, and is then well described by simple engineering models like the Jensen wake model (JWM). We generalise the latter deterministic models to a statistical meandering wake model (SMWM), where a random directional deflection is assigned to a narrow wake in such a way that on average it resembles a broad Jensen wake. In a second step, the model is further generalised to wind-farm level, where the deflections of the multiple wakes are treated as independently and identically distributed random variables. When carefully calibrated to the Nysted wind farm, the ensemble average of the statistical model produces the same wind-direction dependence of the power efficiency as obtained from the standard Jensen model. Upon using the JWM to perform a yaw-angle optimisation of wind-farm power output, we find an optimisation gain of 6.7% for the Nysted wind farm when compared to zero yaw angles and averaged over all wind directions. When applying the obtained JWM-based optimised yaw angles to the SMWM, the ensemble-averaged gain is calculated to be 7.5%. This outcome indicates the possible operational robustness of an optimised yaw control for real-life wind farms.

  3. STYLE - A European Project on Structural Integrity: Progress of the work after 2 Years

    International Nuclear Information System (INIS)

    Heussner, Stefan; Nicak, Tomas; Keim, Elisabeth

    2012-01-01

    The overall objective of STYLE is to assess, optimise and develop the use of advanced tools for the structural integrity assessment of components relevant to ageing and life time management and to support the integration of the knowledge created in the project into main-stream nuclear industry assessment codes.

  4. Achieving a Sustainable Urban Form through Land Use Optimisation: Insights from Bekasi City’s Land-Use Plan (2010–2030

    Directory of Open Access Journals (Sweden)

    Rahmadya Trias Handayanto

    2017-02-01

    Full Text Available Cities worldwide have been trying to achieve a sustainable urban form to handle their rapid urban growth. Many sustainable urban forms have been studied and two of them, the compact city and the eco city, were chosen in this study as urban form foundations. Based on these forms, four sustainable city criteria (compactness, compatibility, dependency, and suitability were considered as necessary functions for land use optimisation. This study presents a land use optimisation as a method for achieving a sustainable urban form. Three optimisation methods (particle swarm optimisation, genetic algorithms, and a local search method were combined into a single hybrid optimisation method for land use in Bekasi city, Indonesia. It was also used for examining Bekasi city’s land-use-plan (2010–2030 after optimising current (2015 and future land use (2030. After current land use optimisation, the score of sustainable city criteria increased significantly. Three important centres of land use (commercial, industrial, and residential were also created through clustering the results. These centres were slightly different from centres of the city plan zones. Additional land uses in 2030 were predicted using a nonlinear autoregressive neural network with external input. Three scenarios were used for allocating these additional land uses including sustainable development, government policy, and business-as-usual. Future land use allocation in 2030 found that the sustainable development scenario showed better performance compared to government policy and business-as-usual scenarios.

  5. Discontinuous permeable adsorptive barrier design and cost analysis: a methodological approach to optimisation.

    Science.gov (United States)

    Santonastaso, Giovanni Francesco; Bortone, Immacolata; Chianese, Simeone; Di Nardo, Armando; Di Natale, Michele; Erto, Alessandro; Karatza, Despina; Musmarra, Dino

    2017-09-19

    The following paper presents a method to optimise a discontinuous permeable adsorptive barrier (PAB-D). This method is based on the comparison of different PAB-D configurations obtained by changing some of the main PAB-D design parameters. In particular, the well diameters, the distance between two consecutive passive wells and the distance between two consecutive well lines were varied, and a cost analysis for each configuration was carried out in order to define the best performing and most cost-effective PAB-D configuration. As a case study, a benzene-contaminated aquifer located in an urban area in the north of Naples (Italy) was considered. The PAB-D configuration with a well diameter of 0.8 m resulted the best optimised layout in terms of performance and cost-effectiveness. Moreover, in order to identify the best configuration for the remediation of the aquifer studied, a comparison with a continuous permeable adsorptive barrier (PAB-C) was added. In particular, this showed a 40% reduction of the total remediation costs by using the optimised PAB-D.

  6. Infrastructure optimisation via MBR retrofit: a design guide.

    Science.gov (United States)

    Bagg, W K

    2009-01-01

    Wastewater management is continually evolving with the development and implementation of new, more efficient technologies. One of these is the Membrane Bioreactor (MBR). Although a relatively new technology in Australia, MBR wastewater treatment has been widely used elsewhere for over 20 years, with thousands of MBRs now in operation worldwide. Over the past 5 years, MBR technology has been enthusiastically embraced in Australia as a potential treatment upgrade option, and via retrofit typically offers two major benefits: (1) more capacity using mostly existing facilities, and (2) very high quality treated effluent. However, infrastructure optimisation via MBR retrofit is not a simple or low-cost solution and there are many factors which should be carefully evaluated before deciding on this method of plant upgrade. The paper reviews a range of design parameters which should be carefully evaluated when considering an MBR retrofit solution. Several actual and conceptual case studies are considered to demonstrate both advantages and disadvantages. Whilst optimising existing facilities and production of high quality water for reuse are powerful drivers, it is suggested that MBRs are perhaps not always the most sustainable Whole-of-Life solution for a wastewater treatment plant upgrade, especially by way of a retrofit.

  7. Merchandise and Replenishment Planning Optimisation for Fashion Retail

    Directory of Open Access Journals (Sweden)

    Raffaele Iannone

    2013-08-01

    Full Text Available The integration among different companies functions, collaborative planning and the elaboration of focused distribution plans are critical to the success of each kind of company working in the complex retail sector. In this contest, the present work proposes the description of a model able to support coordinated strategic choices continually made by Supply Chain (SC actors. The final objective is achievement of the full optimisation of Merchandise & Replenishment Planning phases, identifying the right replenishment quantities and periods. To test the proposed model’s effectiveness, it was applied to an important Italian fashion company in the complex field of fast-fashion, a sector in which promptness is a main competitive leverage and, therefore, the planning cannot exclude the time variable. The passage from a total push strategy, currently used by the company, to a push-pull one, suggested by the model, allowed us not only to estimate a reduction in goods quantities to purchase at the beginning of a sales period (with considerable economic savings, but also elaborate a focused replenishment plan that permits reduction and optimisation of departures from network warehouses to Points of Sale (POS.

  8. The Wiluna Uranium Project, Western Australia: Bringing a new project to the market

    International Nuclear Information System (INIS)

    Guthrie, V.

    2014-01-01

    The Wiluna Uranium Project is the first uranium mine in Western Australia to receive Government environmental approval since government policy was changed in 2008 to allow uranium mining in Western Australia. Located 960 km northeast of Perth in remote central Western Australia, the Wiluna Project comprises 76.5 million pounds U_3O_8 [~29,000 tU] in six shallow, calcrete-hosted carnotite uranium deposits. Mining is planned at a rate of 1.3 million tonnes annually to produce 2 million pounds U_3O_8 [~770 tU] production using an alkali leach process. The Project requires initial capital investment of AUD$315M and has an operating cost of US$29-31 per pound [~75-~80 USD/kgU]. During the four years it has taken to gain environmental approval, Toro also progressed technical studies to validate the economic and technical viability of the Project. These included the initial Preliminary Feasibility (PFS) to define the processing train; mining optimisation studies, a Resource Evaluation Pit (REP) and a commercial scale Pilot Plant to verify the mining and processing technologies; and finally, Phase 1 of the Definitive Feasibility Study (DFS) which focussed on the processing plant design. (author)

  9. Intelligent Internet-based information system optimises diabetes mellitus management in communities.

    Science.gov (United States)

    Wei, Xuejuan; Wu, Hao; Cui, Shuqi; Ge, Caiying; Wang, Li; Jia, Hongyan; Liang, Wannian

    2018-05-01

    To evaluate the effect of an intelligent Internet-based information system upon optimising the management of patients diagnosed with type 2 diabetes mellitus (T2DM). In 2015, a T2DM information system was introduced to optimise the management of T2DM patients for 1 year in Fangzhuang community of Beijing, China. A total of 602 T2DM patients who were registered in the health service centre of Fangzhuang community were enrolled based on an isometric sampling technique. The data from 587 patients were used in the final analysis. The intervention effect was subsequently assessed by statistically comparing multiple parameters, such as the prevalence of glycaemic control, standard health management and annual outpatient consultation visits per person, before and after the implementation of the T2DM information system. In 2015, a total of 1668 T2DM patients were newly registered in Fangzhuang community. The glycaemic control rate was calculated as 37.65% in 2014 and significantly elevated up to 62.35% in 2015 ( p information system, the rate of standard health management was increased from 48.04% to 85.01% ( p information system optimised the management of T2DM patients in Fangzhuang community and decreased the outpatient numbers in both community and general hospitals, which played a positive role in assisting T2DM patients and their healthcare providers to better manage this chronic illness.

  10. Characteristics of internal transport barriers from the JET optimised shear database

    International Nuclear Information System (INIS)

    Rochard, F.; Litaudon, X.; Soeldner, F.

    2000-02-01

    The general features of the Internal Transport Barriers (ITBs) obtained in the JET 'Optimised Shear' regime are deduced from the analyses of a large database of discharges including the experiments performed with a mixture of Deuterium-Tritium (D-T) ions. The coupled and complex spatio-temporal dynamics of the ITBs are studied from the radial profiles measurements of the thermal ion and electron temperatures. The spatial locations of the ITBs inside the plasma column are deduced from the radial derivatives of the plasmas profiles. In particular, our analyses show that the radial positions of the ITB follow the same evolution for both the electron and ion temperature profiles. Among the JET 'Optimised Shear' database, we propose to distinguish two categories of discharges depending on the edge conditions: the ITBs are triggered either with an L-mode edge or simultaneously with an edge transport barrier (H-mode). The characteristics of the ITBs and plasma performances of these two categories are compared. Experimental conditions to successfully combine the edge and core transport barriers are given. In particular, emphasis is given on the description and analyses of the 'Optimised Shear' discharges which combine an ITB with an ELMy edge since this operating mode opens the route to high performance regimes which could be extrapolated towards steady-state conditions. (author)

  11. Optimising performance in steady state for a supermarket refrigeration system

    DEFF Research Database (Denmark)

    Green, Torben; Kinnaert, Michel; Razavi-Far, Roozbeh

    2012-01-01

    Using a supermarket refrigeration system as an illustrative example, the paper postulates that by appropriately utilising knowledge of plant operation, the plant wide performance can be optimised based on a small set of variables. Focusing on steady state operations, the total system performance...

  12. Assessment of grid optimisation measures for the German transmission grid using open source grid data

    Science.gov (United States)

    Böing, F.; Murmann, A.; Pellinger, C.; Bruckmeier, A.; Kern, T.; Mongin, T.

    2018-02-01

    The expansion of capacities in the German transmission grid is a necessity for further integration of renewable energy sources into the electricity sector. In this paper, the grid optimisation measures ‘Overhead Line Monitoring’, ‘Power-to-Heat’ and ‘Demand Response in the Industry’ are evaluated and compared against conventional grid expansion for the year 2030. Initially, the methodical approach of the simulation model is presented and detailed descriptions of the grid model and the used grid data, which partly originates from open-source platforms, are provided. Further, this paper explains how ‘Curtailment’ and ‘Redispatch’ can be reduced by implementing grid optimisation measures and how the depreciation of economic costs can be determined considering construction costs. The developed simulations show that the conventional grid expansion is more efficient and implies more grid relieving effects than the evaluated grid optimisation measures.

  13. Friction stir welding: multi-response optimisation using Taguchi-based GRA

    Directory of Open Access Journals (Sweden)

    Jitender Kundu

    2016-01-01

    Full Text Available In present experimental work, friction stir welding of aluminium alloy 5083- H321 is performed for optimisation of process parameters for maximum tensile strength. Taguchi’s L9 orthogonal array has been used for three parameters – tool rotational speed (TRS, traverse speed (TS, and tool tilt angle (TTA with three levels. Multi-response optimisation has been carried out through Taguchi-based grey relational analysis. The grey relational grade has been calculated for all three responses – ultimate tensile strength, percentage elongation, and micro-hardness. Analysis of variance is the tool used for obtaining grey relational grade to find out the significant process parameters. TRS and TS are the two most significant parameters which influence most of the quality characteristics of friction stir welded joint. Validation of predicted values done through confirmation experiments at optimum setting shows a good agreement with experimental values.

  14. Hybrid real-code ant colony optimisation for constrained mechanical design

    Science.gov (United States)

    Pholdee, Nantiwat; Bureerat, Sujin

    2016-01-01

    This paper proposes a hybrid meta-heuristic based on integrating a local search simplex downhill (SDH) method into the search procedure of real-code ant colony optimisation (ACOR). This hybridisation leads to five hybrid algorithms where a Monte Carlo technique, a Latin hypercube sampling technique (LHS) and a translational propagation Latin hypercube design (TPLHD) algorithm are used to generate an initial population. Also, two numerical schemes for selecting an initial simplex are investigated. The original ACOR and its hybrid versions along with a variety of established meta-heuristics are implemented to solve 17 constrained test problems where a fuzzy set theory penalty function technique is used to handle design constraints. The comparative results show that the hybrid algorithms are the top performers. Using the TPLHD technique gives better results than the other sampling techniques. The hybrid optimisers are a powerful design tool for constrained mechanical design problems.

  15. Sampling design optimisation for rainfall prediction using a non-stationary geostatistical model

    Science.gov (United States)

    Wadoux, Alexandre M. J.-C.; Brus, Dick J.; Rico-Ramirez, Miguel A.; Heuvelink, Gerard B. M.

    2017-09-01

    The accuracy of spatial predictions of rainfall by merging rain-gauge and radar data is partly determined by the sampling design of the rain-gauge network. Optimising the locations of the rain-gauges may increase the accuracy of the predictions. Existing spatial sampling design optimisation methods are based on minimisation of the spatially averaged prediction error variance under the assumption of intrinsic stationarity. Over the past years, substantial progress has been made to deal with non-stationary spatial processes in kriging. Various well-documented geostatistical models relax the assumption of stationarity in the mean, while recent studies show the importance of considering non-stationarity in the variance for environmental processes occurring in complex landscapes. We optimised the sampling locations of rain-gauges using an extension of the Kriging with External Drift (KED) model for prediction of rainfall fields. The model incorporates both non-stationarity in the mean and in the variance, which are modelled as functions of external covariates such as radar imagery, distance to radar station and radar beam blockage. Spatial predictions are made repeatedly over time, each time recalibrating the model. The space-time averaged KED variance was minimised by Spatial Simulated Annealing (SSA). The methodology was tested using a case study predicting daily rainfall in the north of England for a one-year period. Results show that (i) the proposed non-stationary variance model outperforms the stationary variance model, and (ii) a small but significant decrease of the rainfall prediction error variance is obtained with the optimised rain-gauge network. In particular, it pays off to place rain-gauges at locations where the radar imagery is inaccurate, while keeping the distribution over the study area sufficiently uniform.

  16. Metal Removal Process Optimisation using Taguchi Method - Simplex Algorithm (TM-SA) with Case Study Applications

    OpenAIRE

    Ajibade, Oluwaseyi A.; Agunsoye, Johnson O.; Oke, Sunday A.

    2018-01-01

    In the metal removal process industry, the current practice to optimise cutting parameters adoptsa conventional method. It is based on trial and error, in which the machine operator uses experience,coupled with handbook guidelines to determine optimal parametric values of choice. This method is notaccurate, is time-consuming and costly. Therefore, there is a need for a method that is scientific, costeffectiveand precise. Keeping this in mind, a different direction for process optimisation is ...

  17. Public Value Creation Enabled by Healthcare IS Projects – a resource-based-view

    DEFF Research Database (Denmark)

    Schlichter, Bjarne Rerup; Svejvig, Per; Laursen, Markus

    Creation of value from IT projects is a recurring theme that has diffused into healthcare information sys-tems (HIS). By applying a resource-based-view on findings from a study on the optimisation project of an integrated health information system (HIS) we develop a framework of capabilities needed...... in a public HIS setting to create value. The framework consists of Professional- , Organisational-, Patient Perceived- and Employee Perceived-Value dimensions. HIS is partly overlooked in the public management literature and the aspect of emergence and (personal as well as organisational) learning plays...... an important role in the creation value in HIS-projects....

  18. Analysis and optimisation of a mixed fluid cascade (MFC) process

    Science.gov (United States)

    Ding, He; Sun, Heng; Sun, Shoujun; Chen, Cheng

    2017-04-01

    A mixed fluid cascade (MFC) process that comprises three refrigeration cycles has great capacity for large-scale LNG production, which consumes a great amount of energy. Therefore, any performance enhancement of the liquefaction process will significantly reduce the energy consumption. The MFC process is simulated and analysed by use of proprietary software, Aspen HYSYS. The effect of feed gas pressure, LNG storage pressure, water-cooler outlet temperature, different pre-cooling regimes, liquefaction, and sub-cooling refrigerant composition on MFC performance are investigated and presented. The characteristics of its excellent numerical calculation ability and the user-friendly interface of MATLAB™ and powerful thermo-physical property package of Aspen HYSYS are combined. A genetic algorithm is then invoked to optimise the MFC process globally. After optimisation, the unit power consumption can be reduced to 4.655 kW h/kmol, or 4.366 kW h/kmol on condition that the compressor adiabatic efficiency is 80%, or 85%, respectively. Additionally, to improve the process further, with regards its thermodynamic efficiency, configuration optimisation is conducted for the MFC process and several configurations are established. By analysing heat transfer and thermodynamic performances, the configuration entailing a pre-cooling cycle with three pressure levels, liquefaction, and a sub-cooling cycle with one pressure level is identified as the most efficient and thus optimal: its unit power consumption is 4.205 kW h/kmol. Additionally, the mechanism responsible for the weak performance of the suggested liquefaction cycle configuration lies in the unbalanced distribution of cold energy in the liquefaction temperature range.

  19. Satellite Vibration Testing: Angle optimisation method to Reduce Overtesting

    Science.gov (United States)

    Knight, Charly; Remedia, Marcello; Aglietti, Guglielmo S.; Richardson, Guy

    2018-06-01

    Spacecraft overtesting is a long running problem, and the main focus of most attempts to reduce it has been to adjust the base vibration input (i.e. notching). Instead this paper examines testing alternatives for secondary structures (equipment) coupled to the main structure (satellite) when they are tested separately. Even if the vibration source is applied along one of the orthogonal axes at the base of the coupled system (satellite plus equipment), the dynamics of the system and potentially the interface configuration mean the vibration at the interface may not occur all along one axis much less the corresponding orthogonal axis of the base excitation. This paper proposes an alternative testing methodology in which the testing of a piece of equipment occurs at an offset angle. This Angle Optimisation method may have multiple tests but each with an altered input direction allowing for the best match between all specified equipment system responses with coupled system tests. An optimisation process that compares the calculated equipment RMS values for a range of inputs with the maximum coupled system RMS values, and is used to find the optimal testing configuration for the given parameters. A case study was performed to find the best testing angles to match the acceleration responses of the centre of mass and sum of interface forces for all three axes, as well as the von Mises stress for an element by a fastening point. The angle optimisation method resulted in RMS values and PSD responses that were much closer to the coupled system when compared with traditional testing. The optimum testing configuration resulted in an overall average error significantly smaller than the traditional method. Crucially, this case study shows that the optimum test campaign could be a single equipment level test opposed to the traditional three orthogonal direction tests.

  20. Identification of the mechanical behaviour of biopolymer composites using multistart optimisation technique

    KAUST Repository

    Brahim, Elhacen

    2013-10-01

    This paper aims at identifying the mechanical behaviour of starch-zein composites as a function of zein content using a novel optimisation technique. Starting from bending experiments, force-deflection response is used to derive adequate mechanical parameters representing the elastic-plastic behaviour of the studied material. For such a purpose, a finite element model is developed accounting for a simple hardening rule, namely isotropic hardening model. A deterministic optimisation strategy is implemented to provide rapid matching between parameters of the constitutive law and the observed behaviour. Results are discussed based on the robustness of the numerical approach and predicted tendencies with regards to the role of zein content. © 2013 Elsevier Ltd.

  1. Design and optimisation of dual-mode heat pump systems using natural fluids

    International Nuclear Information System (INIS)

    Zhang Wenling; Klemeš, Jiří Jaromír; Kim, Jin-Kuk

    2012-01-01

    The paper introduces new multi-period modelling and design methodology for dual-mode heat pumps using natural fluids. First, a mathematical model is developed to capture thermodynamic and operating characteristics of dual-mode heat pump systems, subject to different ambient temperatures. The multi-period optimisation framework has been developed to reflect different ambient conditions and its influences on heat pump performance, as well as to determine a system capacity of heat pump which allows systematic economic trade-offs between supplementary heating (or cooling) and operating cost for heat pump. Case study considering three geographical locations with different heating and cooling demands is presented to illustrate the importance of using multi-period optimisation for the design of heat pump systems.

  2. Optimisation of liquid scintillation counting conditions to determine low activity levels of tritium and radiostrontium in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Rauret, Gemma; Mestres, J.S.; Ribera, Merce; Rajadel, Pilar (Barcelona Univ. (Spain). Dept. de Quimica Analitica)

    1990-08-01

    An optimisation of the counting conditions for the measurement of aqueous solutions of tritium or radiostrontium using Insta-Gel II as scintillator is presented. The variables optimised were the window, the ratio of mass of sample to mass of scintillator and the total volume of the counting mixture. An optimisation function which takes into account each of these variables, the background and also the efficiency is proposed. The conditions established allow the lowest possible detection limit to be reached. For tritium, this value was compared with that obtained when the standard method for water analysis was applied. (author).

  3. Radiation protection optimisation techniques and their application in industry

    Energy Technology Data Exchange (ETDEWEB)

    Lefaure, C

    1997-12-31

    Since the International Commission on Radiation Protection (ICRP) recommendation 60, the optimisation principle appears to be the core of the radiation protection system. In practice applying it, means implementing an approach both predictive and evolutionary - that relies essentially on a prudent and responsible state of mind. the formal expression of this process, called optimization procedure, implies and indispensable tool for its implementation: the system of monetary values for the unit of collective dose. During the last few years, feed ALARA principle means that a global work management approach must be adopted, considering together all factors contributing to radiation dose. In the nuclear field, the ALARA approach appears to be more successful when implemented in the framework of a managerial approach through structure ALARA programmes. Outside the nuclear industry it is necessary to clearly define priorities through generic optimisation studies and ALARA audits. At the international level much efforts remain to be done to expand efficiently the ALARA process to internal exposure as well as to public exposure. (author) 2 graphs, 5 figs., 3 tabs.

  4. Radiation protection optimisation techniques and their application in industry

    International Nuclear Information System (INIS)

    Lefaure, C.

    1996-01-01

    Since the International Commission on Radiation Protection (ICRP) recommendation 60, the optimisation principle appears to be the core of the radiation protection system. In practice applying it, means implementing an approach both predictive and evolutionary - that relies essentially on a prudent and responsible state of mind. the formal expression of this process, called optimization procedure, implies and indispensable tool for its implementation: the system of monetary values for the unit of collective dose. During the last few years, feed ALARA principle means that a global work management approach must be adopted, considering together all factors contributing to radiation dose. In the nuclear field, the ALARA approach appears to be more successful when implemented in the framework of a managerial approach through structure ALARA programmes. Outside the nuclear industry it is necessary to clearly define priorities through generic optimisation studies and ALARA audits. At the international level much efforts remain to be done to expand efficiently the ALARA process to internal exposure as well as to public exposure. (author)

  5. Some Current Problems in Optimisation of Radiation Protection System

    International Nuclear Information System (INIS)

    Franic, Z.; Prlic, I.

    2001-01-01

    Full text: The current system of radiation protection is generally based on recommendations promulgated in the International Commission on Radiological Protection (ICRP) publication 60. These principles and recommendations were subsequently adopted by the International Atomic Energy Agency (IAEA) in International Basic Safety Standards for Protection against Ionising Radiation and for the Safety of Radiation Sources (BSS). However, in recent years certain problems have arisen such as application of risk factors at low doses, use and interpretation of a collective dose, concept of dose commitment, optimisation of all types of occupational exposure and practices, implementation of ALARA approach in the common occupational as well as in quite complex situations etc. In this paper are presented some of the issues that have to be addressed in the development of the new ICRP Recommendations that are planned to be developed in next four or five years. As the new radiation protection philosophy shifts from society-based control of stochastic risks to an individual-based policy, consequently it will require introduction of modified approach to optimisation process and probably introduction of some new dosimetric quantities. (author)

  6. Radiation protection optimisation techniques and their application in industry

    Energy Technology Data Exchange (ETDEWEB)

    Lefaure, C

    1996-12-31

    Since the International Commission on Radiation Protection (ICRP) recommendation 60, the optimisation principle appears to be the core of the radiation protection system. In practice applying it, means implementing an approach both predictive and evolutionary - that relies essentially on a prudent and responsible state of mind. the formal expression of this process, called optimization procedure, implies and indispensable tool for its implementation: the system of monetary values for the unit of collective dose. During the last few years, feed ALARA principle means that a global work management approach must be adopted, considering together all factors contributing to radiation dose. In the nuclear field, the ALARA approach appears to be more successful when implemented in the framework of a managerial approach through structure ALARA programmes. Outside the nuclear industry it is necessary to clearly define priorities through generic optimisation studies and ALARA audits. At the international level much efforts remain to be done to expand efficiently the ALARA process to internal exposure as well as to public exposure. (author) 2 graphs, 5 figs., 3 tabs.

  7. Heterogeneous fuels for minor actinides transmutation: Fuel performance codes predictions in the EFIT case study

    Energy Technology Data Exchange (ETDEWEB)

    Calabrese, R., E-mail: rolando.calabrese@enea.i [ENEA, Innovative Nuclear Reactors and Fuel Cycle Closure Division, via Martiri di Monte Sole 4, 40129 Bologna (Italy); Vettraino, F.; Artioli, C. [ENEA, Innovative Nuclear Reactors and Fuel Cycle Closure Division, via Martiri di Monte Sole 4, 40129 Bologna (Italy); Sobolev, V. [SCK.CEN, Belgian Nuclear Research Centre, Boeretang 200, B-2400 Mol (Belgium); Thetford, R. [Serco Technical and Assurance Services, 150 Harwell Business Centre, Didcot OX11 0QB (United Kingdom)

    2010-06-15

    Plutonium recycling in new-generation fast reactors coupled with minor actinides (MA) transmutation in dedicated nuclear systems could achieve a decrease of nuclear waste long-term radiotoxicity by two orders of magnitude in comparison with current once-through strategy. In a double-strata scenario, purpose-built accelerator-driven systems (ADS) could transmute minor actinides. The innovative nuclear fuel conceived for such systems demands significant R and D efforts in order to meet the safety and technical performance of current fuel systems. The Integrated Project EUROTRANS (EUROpean research programme for the TRANSmutation of high level nuclear waste in ADS), part of the EURATOM Framework Programme 6 (FP6), undertook some of this research. EUROTRANS developed from the FP5 research programmes on ADS (PDS-XADS) and on fuels dedicated to MA transmutation (FUTURE, CONFIRM). One of its main objectives is the conceptual design of a small sub-critical nuclear system loaded with uranium-free fuel to provide high MA transmutation efficiency. These principles guided the design of EFIT (European Facility for Industrial Transmutation) in the domain DESIGN of IP EUROTRANS. The domain AFTRA (Advanced Fuels for TRAnsmutation system) identified two composite fuel systems: a ceramic-ceramic (CERCER) where fuel particles are dispersed in a magnesia matrix, and a ceramic-metallic (CERMET) with a molybdenum matrix in the place of MgO matrix to host a ceramic fissile phase. The EFIT fuel is composed of plutonium and MA oxides in solid solution with isotopic vectors typical of LWR spent fuel with 45 MWd/kg{sub HM} discharge burnup and 30 years interim storage before reprocessing. This paper is focused on the thermomechanical state of the hottest fuel pins of two EFIT cores of 400 MW{sub (th)} loaded with either CERCER or CERMET fuels. For calculations three fuel performance codes were used: FEMALE, TRAFIC and TRANSURANUS. The analysis was performed at the beginning of fuel life

  8. Optimising metadata workflows in a distributed information environment

    OpenAIRE

    Robertson, R. John; Barton, Jane

    2005-01-01

    The different purposes present within a distributed information environment create the potential for repositories to enhance their metadata by capitalising on the diversity of metadata available for any given object. This paper presents three conceptual reference models required to achieve this optimisation of metadata workflow: the ecology of repositories, the object lifecycle model, and the metadata lifecycle model. It suggests a methodology for developing the metadata lifecycle model, and ...

  9. Optimisation of the Ti/Al/Ni/Au ohmic contact on AlGaN/GaN FET structures

    NARCIS (Netherlands)

    Jacobs, B.; Krämer, M.C.J.C.M.; Geluk, E.J.; Karouta, F.

    2002-01-01

    We present a systematic approach to reduce the resistance of ohmic contacts on AlGaN/GaN FET structures. We have optimised the Ti/Al/Ni/Au contact with respect to the metal composition and annealing conditions. Our optimised contact has a very low contact resistance of 0.2 ohm mm (7.3 x 10^-7 ohm

  10. Parameter Optimisation for the Behaviour of Elastic Models over Time

    DEFF Research Database (Denmark)

    Mosegaard, Jesper

    2004-01-01

    Optimisation of parameters for elastic models is essential for comparison or finding equivalent behaviour of elastic models when parameters cannot simply be transferred or converted. This is the case with a large range of commonly used elastic models. In this paper we present a general method tha...

  11. Estimators for initial conditions for optimisation in learning hydraulic systems

    NARCIS (Netherlands)

    Post, W.J.A.E.M.; Burrows, C.R.; Edge, K.A.

    1998-01-01

    In Learning Hydraulic Systems (LHS1. developed at the Eindhoven University of Technology, a specialised optimisation routine is employed In order to reduce energy losses in hydraulic systems. Typical load situations which can be managed by LHS are variable cyclic loads, as can be observed In many

  12. Plant-wide dynamic and static optimisation of supermarket refrigeration systems

    DEFF Research Database (Denmark)

    Green, Torben; Izadi-Zamanabadi, Roozbeh; Razavi-Far, Roozbeh

    2013-01-01

    Optimising the operation of a supermarket refrigeration system under dynamic as well as steadystate conditions is addressedin thispaper. For thispurpose anappropriateperformance function that encompasses food quality, system efficiency, and also component reliability is established. The choice...... in the system. Simulation results is used to substantiate the suggestedmethodology....

  13. Multi-objective optimisation of aircraft flight trajectories in the ATM and avionics context

    Science.gov (United States)

    Gardi, Alessandro; Sabatini, Roberto; Ramasamy, Subramanian

    2016-05-01

    The continuous increase of air transport demand worldwide and the push for a more economically viable and environmentally sustainable aviation are driving significant evolutions of aircraft, airspace and airport systems design and operations. Although extensive research has been performed on the optimisation of aircraft trajectories and very efficient algorithms were widely adopted for the optimisation of vertical flight profiles, it is only in the last few years that higher levels of automation were proposed for integrated flight planning and re-routing functionalities of innovative Communication Navigation and Surveillance/Air Traffic Management (CNS/ATM) and Avionics (CNS+A) systems. In this context, the implementation of additional environmental targets and of multiple operational constraints introduces the need to efficiently deal with multiple objectives as part of the trajectory optimisation algorithm. This article provides a comprehensive review of Multi-Objective Trajectory Optimisation (MOTO) techniques for transport aircraft flight operations, with a special focus on the recent advances introduced in the CNS+A research context. In the first section, a brief introduction is given, together with an overview of the main international research initiatives where this topic has been studied, and the problem statement is provided. The second section introduces the mathematical formulation and the third section reviews the numerical solution techniques, including discretisation and optimisation methods for the specific problem formulated. The fourth section summarises the strategies to articulate the preferences and to select optimal trajectories when multiple conflicting objectives are introduced. The fifth section introduces a number of models defining the optimality criteria and constraints typically adopted in MOTO studies, including fuel consumption, air pollutant and noise emissions, operational costs, condensation trails, airspace and airport operations

  14. Optimisation of radiation protection for the new european pressurized water reactor (EPR)

    International Nuclear Information System (INIS)

    Miniere, D.; Beneteau, Y.; Le Guen, Bernard

    2008-01-01

    Full text: As part of the EPR (European Pressurized Reactor) project being deployed at Flamanville, EDF has pro actively made the decision to focus on radiation protection (RP) aspects right from the start of the design phase, as it has done with nuclear safety. The approach adopted for managing RP-significant activities has been to include all involved stake holders -designers, licensee and contractor companies- in the three successive phases, starting with a survey among workers and designers, followed by a proposal review, and finally ending with the decision-making phase entrusted to an ALARA committee. The RP target set by EDF for this new reactor is to engage in an effort of continuous improvement and optimisation, through benchmarking with the best performing plants of the fleet. The collective dose target is currently set at 0.35 man.Sv/year per unit. In addition to other aspects, efforts will focus on shortening the duration of the highest-dose jobs, with a new challenge being set for work performed in the reactor building during normal operations, the aim being to improve plant availability. The plan is for work to be performed 7 days prior to shutting down the reactor and 3 days afterwards, in order to make logistical arrangements for forthcoming jobs. Without this reduction, the estimated drop is currently 4.5% of annual dose. For this purpose, two areas have been set up in the EPR 's reactor building: one no-go area for containing leaks from the primary circuit, and one accessible area for normal operations, separated from the no-go area by purpose-built ventilation equipment and facilities. To offer protection against radioactive flux (neutrons and high energy), RP studies have resulted in the installation of a concrete floor and of nuclear shielding at the outlets of primary circuit pipes. Steam generator bunkers and pumps have also been reinforced. All these measures will ensure that the accessible area can be posted as a green area (dose rate < 25

  15. Optimised mounting conditions for poly (ether sulfone) in radiation detection.

    Science.gov (United States)

    Nakamura, Hidehito; Shirakawa, Yoshiyuki; Sato, Nobuhiro; Yamada, Tatsuya; Kitamura, Hisashi; Takahashi, Sentaro

    2014-09-01

    Poly (ether sulfone) (PES) is a candidate for use as a scintillation material in radiation detection. Its characteristics, such as its emission spectrum and its effective refractive index (based on the emission spectrum), directly affect the propagation of light generated to external photodetectors. It is also important to examine the presence of background radiation sources in manufactured PES. Here, we optimise the optical coupling and surface treatment of the PES, and characterise its background. Optical grease was used to enhance the optical coupling between the PES and the photodetector; absorption by the grease of short-wavelength light emitted from PES was negligible. Diffuse reflection induced by surface roughening increased the light yield for PES, despite the high effective refractive index. Background radiation derived from the PES sample and its impurities was negligible above the ambient, natural level. Overall, these results serve to optimise the mounting conditions for PES in radiation detection. Copyright © 2014 Elsevier Ltd. All rights reserved.

  16. The LHC Project Status and Prospects

    CERN Document Server

    Faugeras, Paul E

    2001-01-01

    The Large Hadron Collider (LHC), CERN's future major facility for high-energy physics, has entered into the construction and preparation for installation phases. After recalling briefly the main machine design choices and challenges, one will review the progress of civil works for the machine and experimental areas and the status of the main LHC components, which are presently series-built and for some of them procured in kind through world-wide collaborations. Report will also be given on the full-scale prototype of an elementary LHC lattice cell, called String 2, which is being commissioned and used for optimising the installation and testing procedures of the LHC. The size and duration of the LHC Project, its intrinsic complexity and the large number of world-wide collaborations involved require rather elaborate project management tools, which will be shortly described. Finally, following the extended running of the LEP and the delay for emptying of the machine tunnel, a new planning for project completion...

  17. Specification, Verification and Optimisation of Business Processes

    DEFF Research Database (Denmark)

    Herbert, Luke Thomas

    is extended with stochastic branching, message passing and reward annotations which allow for the modelling of resources consumed during the execution of a business process. Further, it is shown how this structure can be used to formalise the established business process modelling language Business Process...... fault tree analysis and the automated optimisation of business processes by means of an evolutionary algorithm. This work is motivated by problems that stem from the healthcare sector, and examples encountered in this field are used to illustrate these developments....

  18. Parametric studies and optimisation of pumped thermal electricity storage

    International Nuclear Information System (INIS)

    McTigue, Joshua D.; White, Alexander J.; Markides, Christos N.

    2015-01-01

    Highlights: • PTES is modelled by cycle analysis and a Schumann-style model of the thermal stores. • Optimised trade-off surfaces show a flat efficiency vs. energy density profile. • Overall roundtrip efficiencies of around 70% are not inconceivable. - Abstract: Several of the emerging technologies for electricity storage are based on some form of thermal energy storage (TES). Examples include liquid air energy storage, pumped heat energy storage and, at least in part, advanced adiabatic compressed air energy storage. Compared to other large-scale storage methods, TES benefits from relatively high energy densities, which should translate into a low cost per MW h of storage capacity and a small installation footprint. TES is also free from the geographic constraints that apply to hydro storage schemes. TES concepts for electricity storage rely on either a heat pump or refrigeration cycle during the charging phase to create a hot or a cold storage space (the thermal stores), or in some cases both. During discharge, the thermal stores are depleted by reversing the cycle such that it acts as a heat engine. The present paper is concerned with a form of TES that has both hot and cold packed-bed thermal stores, and for which the heat pump and heat engine are based on a reciprocating Joule cycle, with argon as the working fluid. A thermodynamic analysis is presented based on traditional cycle calculations coupled with a Schumann-style model of the packed beds. Particular attention is paid to the various loss-generating mechanisms and their effect on roundtrip efficiency and storage density. A parametric study is first presented that examines the sensitivity of results to assumed values of the various loss factors and demonstrates the rather complex influence of the numerous design variables. Results of an optimisation study are then given in the form of trade-off surfaces for roundtrip efficiency, energy density and power density. The optimised designs show a

  19. Can we speak of optimisation in the medical and non-electronuclear industrial fields in France

    International Nuclear Information System (INIS)

    Lefaure, C.; Abadia, G.; Aubert, B.

    1995-01-01

    In France, in 1993, more than 10 000 workers, i.e. nearly a quarter of the workers significantly exposed, were working in the medical, research and non-nuclear industrial fields. The annual average dose per significantly exposed worker was 2 mSv for veterinary surgeons, 3 mSv for the medical sector, 5.5 mSv for the non-nuclear industry. In the industrial sector, more than 8% of the exposed workers received an annual dose higher than 15 mSv. Such exposures are neither negligible nor really lower than those of the nuclear industry where the optimisation of radiological protection is currently implemented. So far, no publication has mentioned experience in the other sectors. Optimisation surveys in reference centres, for x-ray examinations or specific industrial practices, especially for the new practices such as interventional radiology, would make it possible to supply other enterprises or radiological services with information on what an optimised practice might be, under reference conditions, as far as radiological protection is concerned. The true difficulties in the implementation of optimisation in the industrial and medical sectors are not those which are commonly put forward (low levels of exposure, lack of resources, complexity...) but rather a lack of relevant data and above all a lack of culture on the residual risk. (authors). 19 refs., 5 tabs., 2 annexes

  20. Optimisation of phase ratio in the triple jump using computer simulation.

    Science.gov (United States)

    Allen, Sam J; King, Mark A; Yeadon, M R Fred

    2016-04-01

    The triple jump is an athletic event comprising three phases in which the optimal proportion of each phase to the total distance jumped, termed the phase ratio, is unknown. This study used a whole-body torque-driven computer simulation model of all three phases of the triple jump to investigate optimal technique. The technique of the simulation model was optimised by varying torque generator activation parameters using a Genetic Algorithm in order to maximise total jump distance, resulting in a hop-dominated technique (35.7%:30.8%:33.6%) and a distance of 14.05m. Optimisations were then run with penalties forcing the model to adopt hop and jump phases of 33%, 34%, 35%, 36%, and 37% of the optimised distance, resulting in total distances of: 13.79m, 13.87m, 13.95m, 14.05m, and 14.02m; and 14.01m, 14.02m, 13.97m, 13.84m, and 13.67m respectively. These results indicate that in this subject-specific case there is a plateau in optimum technique encompassing balanced and hop-dominated techniques, but that a jump-dominated technique is associated with a decrease in performance. Hop-dominated techniques are associated with higher forces than jump-dominated techniques; therefore optimal phase ratio may be related to a combination of strength and approach velocity. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Fractures in sport: Optimising their management and outcome

    Science.gov (United States)

    Robertson, Greg AJ; Wood, Alexander M

    2015-01-01

    Fractures in sport are a specialised cohort of fracture injuries, occurring in a high functioning population, in which the goals are rapid restoration of function and return to play with the minimal symptom profile possible. While the general principles of fracture management, namely accurate fracture reduction, appropriate immobilisation and timely rehabilitation, guide the treatment of these injuries, management of fractures in athletic populations can differ significantly from those in the general population, due to the need to facilitate a rapid return to high demand activities. However, despite fractures comprising up to 10% of all of sporting injuries, dedicated research into the management and outcome of sport-related fractures is limited. In order to assess the optimal methods of treating such injuries, and so allow optimisation of their outcome, the evidence for the management of each specific sport-related fracture type requires assessment and analysis. We present and review the current evidence directing management of fractures in athletes with an aim to promote valid innovative methods and optimise the outcome of such injuries. From this, key recommendations are provided for the management of the common fracture types seen in the athlete. Six case reports are also presented to illustrate the management planning and application of sport-focussed fracture management in the clinical setting. PMID:26716081

  2. Optimisation of Storage for Concentrated Solar Power Plants

    Directory of Open Access Journals (Sweden)

    Luigi Cirocco

    2014-12-01

    Full Text Available The proliferation of non-scheduled generation from renewable electrical energy sources such concentrated solar power (CSP presents a need for enabling scheduled generation by incorporating energy storage; either via directly coupled Thermal Energy Storage (TES or Electrical Storage Systems (ESS distributed within the electrical network or grid. The challenges for 100% renewable energy generation are: to minimise capitalisation cost and to maximise energy dispatch capacity. The aims of this review article are twofold: to review storage technologies and to survey the most appropriate optimisation techniques to determine optimal operation and size of storage of a system to operate in the Australian National Energy Market (NEM. Storage technologies are reviewed to establish indicative characterisations of energy density, conversion efficiency, charge/discharge rates and costings. A partitioning of optimisation techniques based on methods most appropriate for various time scales is performed: from “whole of year”, seasonal, monthly, weekly and daily averaging to those best suited matching the NEM bid timing of five minute dispatch bidding, averaged on the half hour as the trading settlement spot price. Finally, a selection of the most promising research directions and methods to determine the optimal operation and sizing of storage for renewables in the grid is presented.

  3. LHCb: Design of a Highly Optimised Vacuum Chamber Support for the LHCb Experiment

    CERN Multimedia

    Leduc, L; Veness, R

    2011-01-01

    The beam vacuum chamber in the LHCb experimental area passes through the centre of a large aperture dipole magnet. The vacuum chamber and all its support systems lie in the acceptance of the detector, so must be highly optimised for transparency to particles. As part of the upgrade programme for the LHCb vacuum system, the support system has been re-designed using advanced lightweight materials. In this paper we discuss the physics motivation for the modifications, the criteria for the selection of materials and tests performed to qualify them for the particular environment of a particle physics experiment. We also present the design of the re-optimised support system.

  4. Optimisation of the image resolution of a positron emission tomograph

    International Nuclear Information System (INIS)

    Ziemons, K.

    1993-10-01

    The resolution and the respective signal-to-noise ratios of reconstructed pictures were a point of main interest of the work for optimisation of PET systems. Monte-Carlo modelling calculations were applied to derive possible improvements of the technical design or performance of the PET system. (DG) [de

  5. Optimisation of Heterogeneous Migration Paths to High Bandwidth Home Connections

    NARCIS (Netherlands)

    Phillipson, F.

    2017-01-01

    Operators are building architectures and systems for delivering voice, audio, and data services at the required speed for now and in the future. For fixed access networks, this means in many countries a shift from copper based to fibre based access networks. This paper proposes a method to optimise

  6. On the impact of optimisation models in maintenance decision making: the state of the art

    International Nuclear Information System (INIS)

    Dekker, Rommert; Scarf, Philip A.

    1998-01-01

    In this paper we discuss the state of the art in applications of maintenance optimisation models. After giving a short introduction to the area, we consider several ways in which models may be used to optimise maintenance, such as case studies, operational and strategic decision support systems, and give examples of each of them. Next we discuss several areas where the models have been applied successfully. These include civil structure and aeroplane maintenance. From a comparative point of view, we discuss future prospects

  7. Optimisation of the microencapsulation of tuna oil in gelatin-sodium hexametaphosphate using complex coacervation.

    Science.gov (United States)

    Wang, Bo; Adhikari, Benu; Barrow, Colin J

    2014-09-01

    The microencapsulation of tuna oil in gelatin-sodium hexametaphosphate (SHMP) using complex coacervation was optimised for the stabilisation of omega-3 oils, for use as a functional food ingredient. Firstly, oil stability was optimised by comparing the accelerated stability of tuna oil in the presence of various commercial antioxidants, using a Rancimat™. Then zeta-potential (mV), turbidity and coacervate yield (%) were measured and optimised for complex coacervation. The highest yield of complex coacervate was obtained at pH 4.7 and at a gelatin to SHMP ratio of 15:1. Multi-core microcapsules were formed when the mixed microencapsulation system was cooled to 5 °C at a rate of 12 °C/h. Crosslinking with transglutaminase followed by freeze drying resulted in a dried powder with an encapsulation efficiency of 99.82% and a payload of 52.56%. Some 98.56% of the oil was successfully microencapsulated and accelerated stability using a Rancimat™ showed stability more than double that of non-encapsulated oil. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Optimising training data for ANNs with Genetic Algorithms

    OpenAIRE

    Kamp , R. G.; Savenije , H. H. G.

    2006-01-01

    International audience; Artificial Neural Networks (ANNs) have proved to be good modelling tools in hydrology for rainfall-runoff modelling and hydraulic flow modelling. Representative datasets are necessary for the training phase in which the ANN learns the model's input-output relations. Good and representative training data is not always available. In this publication Genetic Algorithms (GA) are used to optimise training datasets. The approach is tested with an existing hydraulic model in ...

  9. Optimising training data for ANNs with Genetic Algorithms

    OpenAIRE

    R. G. Kamp; R. G. Kamp; H. H. G. Savenije

    2006-01-01

    Artificial Neural Networks (ANNs) have proved to be good modelling tools in hydrology for rainfall-runoff modelling and hydraulic flow modelling. Representative datasets are necessary for the training phase in which the ANN learns the model's input-output relations. Good and representative training data is not always available. In this publication Genetic Algorithms (GA) are used to optimise training datasets. The approach is tested with an existing hydraulic model in The Netherlands. An...

  10. Sustainable Mining Land Use for Lignite Based Energy Projects

    Science.gov (United States)

    Dudek, Michal; Krysa, Zbigniew

    2017-12-01

    This research aims to discuss complex lignite based energy projects economic viability and its impact on sustainable land use with respect to project risk and uncertainty, economics, optimisation (e.g. Lerchs and Grossmann) and importance of lignite as fuel that may be expressed in situ as deposit of energy. Sensitivity analysis and simulation consist of estimated variable land acquisition costs, geostatistics, 3D deposit block modelling, electricity price considered as project product price, power station efficiency and power station lignite processing unit cost, CO2 allowance costs, mining unit cost and also lignite availability treated as lignite reserves kriging estimation error. Investigated parameters have nonlinear influence on results so that economically viable amount of lignite in optimal pit varies having also nonlinear impact on land area required for mining operation.

  11. Optimising cardiac/angiographic digital images using a Butternut as the image quality phantom

    International Nuclear Information System (INIS)

    Bibbo, G.; Balman, D.

    2008-01-01

    Full text: Digital images, whether produced by image intensifiers, flat panels or computed radiography imaging plates, have a broad dynamic range and, thus, there is a need to adjust the exposure parameters of the imaging protocols to obtain diagnostic images without over exposing patients. The default exposure techniques of protocols delivered with the imaging equipment are in general set to produce high quality images at the expense of high radiation doses to patients. Ideally, these protocols should be optimised for best possible image quality at the lowest possible patient dose, particularly for paediatric patients. Manufacturers of equipment do not generally supply paediatric protocols and, thus, the default settings of the adult protocols have to be adjusted for paediatric patients. Optimising imaging protocols is not a trivial matter and, without a suitable phantom, it is difficult and time consuming. Commercial phantoms are commonly used to optimise adult protocols, but these are made of dry materials such as perspex, Teflon, aluminium, dry bone as in dry skulls, or a combination of these materials. The problem with these phantoms is that the features on their images are artificial, not simulating any characteristics of patients' anatomic details. In optimising paediatric protocols for our new cardiac/angiographic Siemens Biplane Digital Imaging System, we searched for a paediatric phantom with moisture content, and found that the humble butternut pumpkin (cucurbita moschate) from the squash family makes a good paediatric phantom, particularly, when it is injected with contrast. The part of the butternut that is useful as a phantom is the pulp, i.e., the part that contains the seeds. This is also the part where the contrast is injected. The image of the pulp contains structures that are natural as the butternut is the fruit of a living plant. The image of the seeds is suitable for low-level contrast detectability while fine structures enhanced by the

  12. Simultaneous Topology, Shape, and Sizing Optimisation of Plane Trusses with Adaptive Ground Finite Elements Using MOEAs

    Directory of Open Access Journals (Sweden)

    Norapat Noilublao

    2013-01-01

    Full Text Available This paper proposes a novel integrated design strategy to accomplish simultaneous topology shape and sizing optimisation of a two-dimensional (2D truss. An optimisation problem is posed to find a structural topology, shape, and element sizes of the truss such that two objective functions, mass and compliance, are minimised. Design constraints include stress, buckling, and compliance. The procedure for an adaptive ground elements approach is proposed and its encoding/decoding process is detailed. Two sets of design variables defining truss layout, shape, and element sizes at the same time are applied. A number of multiobjective evolutionary algorithms (MOEAs are implemented to solve the design problem. Comparative performance based on a hypervolume indicator shows that multiobjective population-based incremental learning (PBIL is the best performer. Optimising three design variable types simultaneously is more efficient and effective.

  13. Integration of Monte-Carlo ray tracing with a stochastic optimisation method: application to the design of solar receiver geometry.

    Science.gov (United States)

    Asselineau, Charles-Alexis; Zapata, Jose; Pye, John

    2015-06-01

    A stochastic optimisation method adapted to illumination and radiative heat transfer problems involving Monte-Carlo ray-tracing is presented. A solar receiver shape optimisation case study illustrates the advantages of the method and its potential: efficient receivers are identified using a moderate computational cost.

  14. Bus Access Optimisation for FlexRay-based Distributed Embedded Systems

    DEFF Research Database (Denmark)

    Pop, Traian; Pop, Paul; Eles, Petru

    2007-01-01

    -real time communication in a deterministic manner. In this paper, we propose techniques for optimising the FlexRay bus access mechanism of a distributed system, so that the hard real-time deadlines are met for all the tasks and messages in the system. We have evaluated the proposed techniques using...

  15. Optimisation of selective breeding program for Nile tilapia (Oreochromis niloticus)

    NARCIS (Netherlands)

    Trong, T.Q.

    2013-01-01

    The aim of this thesis was to optimise the selective breeding program for Nile tilapia in the Mekong Delta region of Vietnam. Two breeding schemes, the “classic” BLUP scheme following the GIFT method (with pair mating) and a rotational mating scheme with own performance selection and

  16. Optimisation of wort production from rice malt using enzymes and ...

    African Journals Online (AJOL)

    Commercially, rice malt has never been successfully used in brewing because of its low free α-amino nitrogen (FAN) content. This study was designed to optimise rice malt replacement for barley malt in wort production and to improve FAN by adding α-amylase and protease. The response surface methodology (RSM) ...

  17. Biorefinery plant design, engineering and process optimisation

    DEFF Research Database (Denmark)

    Holm-Nielsen, Jens Bo; Ehimen, Ehiazesebhor Augustine

    2014-01-01

    Before new biorefinery systems can be implemented, or the modification of existing single product biomass processing units into biorefineries can be carried out, proper planning of the intended biorefinery scheme must be performed initially. This chapter outlines design and synthesis approaches...... applicable for the planning and upgrading of intended biorefinery systems, and includes discussions on the operation of an existing lignocellulosic-based biorefinery platform. Furthermore, technical considerations and tools (i.e., process analytical tools) which could be applied to optimise the operations...... of existing and potential biorefinery plants are elucidated....

  18. A novel sleep optimisation programme to improve athletes' well-being and performance.

    Science.gov (United States)

    Van Ryswyk, Emer; Weeks, Richard; Bandick, Laura; O'Keefe, Michaela; Vakulin, Andrew; Catcheside, Peter; Barger, Laura; Potter, Andrew; Poulos, Nick; Wallace, Jarryd; Antic, Nick A

    2017-03-01

    To improve well-being and performance indicators in a group of Australian Football League (AFL) players via a six-week sleep optimisation programme. Prospective intervention study following observations suggestive of reduced sleep and excessive daytime sleepiness in an AFL group. Athletes from the Adelaide Football Club were invited to participate if they had played AFL senior-level football for 1-5 years, or if they had excessive daytime sleepiness (Epworth Sleepiness Scale [ESS] >10), measured via ESS. An initial education session explained normal sleep needs, and how to achieve increased sleep duration and quality. Participants (n = 25) received ongoing feedback on their sleep, and a mid-programme education and feedback session. Sleep duration, quality and related outcomes were measured during week one and at the conclusion of the six-week intervention period using sleep diaries, actigraphy, ESS, Pittsburgh Sleep Quality Index, Profile of Mood States, Training Distress Scale, Perceived Stress Scale and the Psychomotor Vigilance Task. Sleep diaries demonstrated an increase in total sleep time of approximately 20 min (498.8 ± 53.8 to 518.7 ± 34.3; p sleep efficiency (p sleep efficiency, fatigue and vigour indicate that a sleep optimisation programme may improve athletes' well-being. More research is required into the effects of sleep optimisation on athletic performance.

  19. Formulation and optimisation of raft-forming chewable tablets containing H2 antagonist.

    Science.gov (United States)

    Prajapati, Shailesh T; Mehta, Anant P; Modhia, Ishan P; Patel, Chhagan N

    2012-10-01

    The purpose of this research work was to formulate raft-forming chewable tablets of H2 antagonist (Famotidine) using a raft-forming agent along with an antacid- and gas-generating agent. Tablets were prepared by wet granulation and evaluated for raft strength, acid neutralisation capacity, weight variation, % drug content, thickness, hardness, friability and in vitro drug release. Various raft-forming agents were used in preliminary screening. A 2(3) full-factorial design was used in the present study for optimisation. The amount of sodium alginate, amount of calcium carbonate and amount sodium bicarbonate were selected as independent variables. Raft strength, acid neutralisation capacity and drug release at 30 min were selected as responses. Tablets containing sodium alginate were having maximum raft strength as compared with other raft-forming agents. Acid neutralisation capacity and in vitro drug release of all factorial batches were found to be satisfactory. The F5 batch was optimised based on maximum raft strength and good acid neutralisation capacity. Drug-excipient compatibility study showed no interaction between the drug and excipients. Stability study of the optimised formulation showed that the tablets were stable at accelerated environmental conditions. It was concluded that raft-forming chewable tablets prepared using an optimum amount of sodium alginate, calcium carbonate and sodium bicarbonate could be an efficient dosage form in the treatment of gastro oesophageal reflux disease.

  20. Radiological procedures: Quality criteria and dose optimisation: French status

    International Nuclear Information System (INIS)

    Grenier, Ph.; Marshall-Depommier, E.; Bourguignon, M.; Beauvais-March, H.; Valero, M.; Lacronique, J.F.; Frijal, G.

    2001-01-01

    The Council Directive 97/43/Euratom of June 30 1997 on health protection of individuals against the dangers of ionising radiation in relation to medical exposure has come into force on May, 13 th 2000. French health directorate has entrusted the 'Office de Protection contre les Rayonnements Ionisants (OPRI)' together with the 'Societe Francaise de Radiologie' (SFR) to implement article 6 related to radiological procedures, in order to bring into operation the principle of optimisation. The most frequent diagnostic radiology and interventional procedures (120 protocols) have been standardised in writing. Corresponding patient dosimetry has been determined from measurements on site, calculations and literature review. The criteria for optimisation have been highlighted for each protocols. With the help of the French Society of Medical Physicists (SFPM), measurements are being collected on a large scale in France. Then, knowing more precisely the patient dosimetry of each protocol, referral criteria will be reviewed and prioritised to implement the principle of justification. The authors will present and explain the chosen methodology (methodology of the Accreditation and Evaluation in Health Agency: ANAES) for completing this two years workload program, and will demonstrate clinical examples as well. (author)

  1. Optimisation of electron beam characteristics by simulated annealing

    International Nuclear Information System (INIS)

    Ebert, M.A.; University of Adelaide, SA; Hoban, P.W.

    1996-01-01

    Full text: With the development of technology in the field of treatment beam delivery, the possibility of tailoring radiation beams (via manipulation of the beam's phase space) is foreseeable. This investigation involved evaluating a method for determining the characteristics of pure electron beams which provided dose distributions that best approximated desired distributions. The aim is to determine which degrees of freedom are advantageous and worth pursuing in a clinical setting. A simulated annealing routine was developed to determine optimum electron beam characteristics. A set of beam elements are defined at the surface of a homogeneous water equivalent phantom defining discrete positions and angles of incidence, and electron energies. The optimal weighting of these elements is determined by the (generally approximate) solution to the linear equation, Dw = d, where d represents the dose distribution calculated over the phantom, w the vector of (50 - 2x10 4 ) beam element relative weights, and D a normalised matrix of dose deposition kernels. In the iterative annealing procedure, beam elements are randomly selected and beam weighting distributions are sampled and used to perturb the selected elements. Perturbations are accepted or rejected according to standard simulated annealing criteria. The result (after the algorithm has terminated due to meeting an iteration or optimisation specification) is an approximate solution for the beam weight vector (w) specified by the above equation. This technique has been applied for several sample dose distributions and phase space restrictions. An example is given of the phase space obtained when endeavouring to conform to a rectangular 100% dose region with polyenergetic though normally incident electrons. For regular distributions, intuitive conclusions regarding the benefits of energy/angular manipulation may be made, whereas for complex distributions, variations in intensity over beam elements of varying energy and

  2. HERCA Position Paper. The process of CT dose optimisation through education and training and role of CT Manufacturers - October 2014. Addendum to HERCA CT Position paper: The process of CT dose optimisation through education and training and the role of the manufacturers - November 2015

    International Nuclear Information System (INIS)

    2014-10-01

    CT is the most important source of exposures to radiation in most developed countries today. For this reason CT dose optimisation is of great importance. In this position paper four main stakeholders who are involved in CT dose optimisation are identified. These are the CT manufacturers, the medical doctors, the CT technologists and the medical physicists. HERCA has been working together with the CT manufacturers and COCIR since 2010 following a self-commitment provided by COCIR in 2011. A number of dose optimisation and management tools have been developed by the CT manufacturers and are now available on modern CT scanners. These are presented in this paper. The process of CT dose optimisation can only be achieved if all the stakeholders involved work together as a team and are educated and trained in the use of CT dose optimisation and management tools. The CT manufacturers have an important role in this process. They need to ensure that their staff is properly trained, they need to provide proper education and training to the other three stakeholders involved and these three stakeholders need to find the time and be willing to be trained. This is clearly stated in this position paper with the aim of ensuring appropriate and effective use of CT imaging equipment. On 1 April 2015, HERCA organised a multi-stakeholder meeting kindly hosted by the French Nuclear Safety Authority (ASN) in its premises in Paris. The stakeholders included: - COCIR, supported by the main manufacturers of CT equipment (GE, Philips, Siemens and Toshiba), - The professional organisations: ESR, ESPR, EFRS, EANM, ESTRO and EFOMP, - The international organisations IAEA, EC, and the US FDA (present as observers). The objective of the meeting was to exchange views with a variety of key stakeholders on issues with regard to the optimised use of computed tomography (CT) scanners. The ultimate goal of this focus on dose optimisation is to ensure the best patient care by providing an optimised

  3. Quadratic head loss approximations for optimisation problems in water supply networks

    NARCIS (Netherlands)

    Pecci, Filippo; Abraham, E.; I, Stoianov

    2017-01-01

    This paper presents a novel analysis of the accuracy of quadratic approximations for the Hazen–Williams (HW) head loss formula, which enables the control of constraint violations in optimisation problems for water supply networks. The two smooth polynomial approximations considered here minimise the

  4. A comparative study of marriage in honey bees optimisation (MBO ...

    African Journals Online (AJOL)

    2012-02-15

    Feb 15, 2012 ... In a typical mating, the queen mates with 7 to 20 drones. Each time the .... Honey bee mating optimisation model's pseudo-code ... for this analysis, which consists of 47 years of monthly time ... tive of Karkheh Reservoir is to control and regulate the flow of ..... Masters thesis, Maastricht University, Maastricht.

  5. A contribution to thermoluminescence dosemeter system optimisation applied to environmental monitoring around nuclear power plants

    International Nuclear Information System (INIS)

    Dies, X.; Ortega, X.; Rosell, J.

    1990-01-01

    The factors that constitute a thermoluminescence dosimetric system have been studied and optimised, with the intention of defining strategies for improving precision and accuracy of TL dosimetry systems for environmental monitoring. An optimisation technique based on fractional factorial designs permitted a reduction in the number of necessary experiments and clarified interactions between various factors. The model for fading over time showed that TL response in LiF:Mg,Ti dosemeters was independent of time between irradiation and readout, and this was applied to fading corrections in nuclear power plant environmental monitoring. (author)

  6. Optimisation and validation of methods to assess single nucleotide polymorphisms (SNPs) in archival histological material

    DEFF Research Database (Denmark)

    Andreassen, C N; Sørensen, Flemming Brandt; Overgaard

    2004-01-01

    only archival specimens are available. This study was conducted to validate protocols optimised for assessment of SNPs based on paraffin embedded, formalin fixed tissue samples.PATIENTS AND METHODS: In 137 breast cancer patients, three TGFB1 SNPs were assessed based on archival histological specimens...... precipitation).RESULTS: Assessment of SNPs based on archival histological material is encumbered by a number of obstacles and pitfalls. However, these can be widely overcome by careful optimisation of the methods used for sample selection, DNA extraction and PCR. Within 130 samples that fulfil the criteria...

  7. Optimisation of timetable-based, stochastic transit assignment models based on MSA

    DEFF Research Database (Denmark)

    Nielsen, Otto Anker; Frederiksen, Rasmus Dyhr

    2006-01-01

    (CRM), such a large-scale transit assignment model was developed and estimated. The Stochastic User Equilibrium problem was solved by the Method of Successive Averages (MSA). However, the model suffered from very large calculation times. The paper focuses on how to optimise transit assignment models...

  8. Reflections on the juridicial roots of the principle of optimisation

    International Nuclear Information System (INIS)

    Lochard, J.; Boehler, M.C.

    1992-01-01

    The disciplines of jurisprudence tend in general towards a rationalisation and stabilisation of social or economic practice and are oriented towards concepts or practices which belong to the field of the determinate. When it comes to the principle of optimising radiological protection, however, the classical juridical technique of administrative law does not exactly answer the problems of implementing this. From the obligations of performance traditionally imposed by the government, a transition to obligation of behaviour by those involved seems to be called for, and this is what makes the optimisation principle difficult to qualify juridically. Instead of a law of command, exemption and control the government must essentially put its trust in the operators of nuclear installations by issuing a standard which sets an objective rather than a standard with the force of a regulation as in the past. Does the future of the juridical sciences in fact lie in the development of an administrative law of the indeterminate which would oblige the government to recognise that, even in the field of the determinate, it is not always government which knows best? While our classical administrative law is a law of command and control, the administrative law of the indeterminate will be that of the law of common effort, framed in collective acts and based on trust, consultation, and obligations of behaviour, all under the control of a judge who intervenes when there is a manifest contradiction between the acts and the promised behaviour. In French law optimisation has remained a general principle unaccompanied by specific provisions for its implementation. The object of our paper is to examine on what juridical foundations it would be possible to apply this principle at practical level without betraying its spirit. (author)

  9. Optimising the Blended Learning Environment: The Arab Open University Experience

    Science.gov (United States)

    Hamdi, Tahrir; Abu Qudais, Mohammed

    2018-01-01

    This paper will offer some insights into possible ways to optimise the blended learning environment based on experience with this modality of teaching at Arab Open University/Jordan branch and also by reflecting upon the results of several meta-analytical studies, which have shown blended learning environments to be more effective than their face…

  10. Optimisation of Transmission Systems by use of Phase Shifting Transformers

    Energy Technology Data Exchange (ETDEWEB)

    Verboomen, J

    2008-10-13

    In this thesis, transmission grids with PSTs (Phase Shifting Transformers) are investigated. In particular, the following goals are put forward: (a) The analysis and quantification of the impact of a PST on a meshed grid. This includes the development of models for the device; (b) The development of methods to obtain optimal coordination of several PSTs in a meshed grid. An objective function should be formulated, and an optimisation method must be adopted to solve the problem; and (c) The investigation of different strategies to use a PST. Chapter 2 gives a short overview of active power flow controlling devices. In chapter 3, a first step towards optimal PST coordination is taken. In chapter 4, metaheuristic optimisation methods are discussed. Chapter 5 introduces DC load flow approximations, leading to analytically closed equations that describe the relation between PST settings and active power flows. In chapter 6, some applications of the methods that are developed in earlier chapters are presented. Chapter 7 contains the conclusions of this thesis, as well as recommendations for future work.

  11. The ATLAS Level-2 Trigger Pilot Project

    CERN Document Server

    Wickens, F J

    2000-01-01

    The Level-2 Trigger Pilot Project of ATLAS, one of the two general purpose LHC experiments, is part of the on-going programme to develop the ATLAS High Level Triggers (HLT). The Level-2 Trigger will receive events at up to 100 kHz, which has to be reduced to a rate suitable for full event-building of the order of 1 kHz. To reduce the data collection bandwidth and processing power required for the challenging Level-2 task it is planned to use Region of Interest guidance (from Level-1) and sequential processing. The Pilot Project included the construction and use of testbeds of up to 48 processing nodes, development of optimised components and computer simulations of a full system. It has shown how the required performance can be achieved, using largely commodity components and operating systems, and validated an architecture for the Level-2 system. This paper describes the principal achievements and conclusions of this project. (28 refs).

  12. Regenesys utility scale energy storage. Project summary

    International Nuclear Information System (INIS)

    2004-01-01

    This report summarises the work to date, the current situation and the future direction of a project carried out by Regenesys Technology Ltd. (RGN) to investigate the benefits of electrochemical energy storage for power generators using renewable energy sources focussing on wind energy. The background to the study is traced covering the progress of the Regenesys energy storage technology, and the milestones achieved and lessons learnt. Details are given of the planned renewable-store-market interface to allow renewable generators optimise revenue under the New Electricity Trading Arrangements (NETA) and help in the connection of the renewable energy to the electric grid system. The four integrated work programmes of the project are described and involve a system study examining market penetration of renewable generators, a technical study into connection of renewable generators and energy storage, a small scale demonstration, and a pilot scale energy storage plant at Little Barton in Cambridgeshire. Problems leading to the closure of the project are discussed

  13. Regenesys utility scale energy storage. Project summary

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    This report summarises the work to date, the current situation and the future direction of a project carried out by Regenesys Technology Ltd. (RGN) to investigate the benefits of electrochemical energy storage for power generators using renewable energy sources focussing on wind energy. The background to the study is traced covering the progress of the Regenesys energy storage technology, and the milestones achieved and lessons learnt. Details are given of the planned renewable-store-market interface to allow renewable generators optimise revenue under the New Electricity Trading Arrangements (NETA) and help in the connection of the renewable energy to the electric grid system. The four integrated work programmes of the project are described and involve a system study examining market penetration of renewable generators, a technical study into connection of renewable generators and energy storage, a small scale demonstration, and a pilot scale energy storage plant at Little Barton in Cambridgeshire. Problems leading to the closure of the project are discussed.

  14. Optimised performance of a plug-in electric vehicle aggregator in energy and reserve markets

    International Nuclear Information System (INIS)

    Shafie-khah, M.; Moghaddam, M.P.; Sheikh-El-Eslami, M.K.; Catalão, J.P.S.

    2015-01-01

    Highlights: • A new model is developed to optimise the performance of a PEV aggregator in the power market. • PEVs aggregator can combine the PEVs and manage the charge/discharge of their batteries. • A new approach to calculate the satisfaction/motivation of PEV owners is proposed. • Several uncertainties are taken into account using a two-stage stochastic programing approach. • The proposed model is proficient in significantly improving the short- and long-term behaviour. - Abstract: In this paper, a new model is developed to optimise the performance of a plug-in Electric Vehicle (EV) aggregator in electricity markets, considering both short- and long-term horizons. EV aggregator as a new player of the power market can aggregate the EVs and manage the charge/discharge of their batteries. The aggregator maximises the profit and optimises EV owners’ revenue by applying changes in tariffs to compete with other market players for retaining current customers and acquiring new owners. On this basis, a new approach to calculate the satisfaction/motivation of EV owners and their market participation is proposed in this paper. Moreover, the behaviour of owners to select their supplying company is considered. The aggregator optimises the self-scheduling programme and submits the best bidding/offering strategies to the day-ahead and real-time markets. To achieve this purpose, the day-ahead and real-time energy and reserve markets are modelled as oligopoly markets, in contrast with previous works that utilised perfectly competitive ones. Furthermore, several uncertainties and constraints are taken into account using a two-stage stochastic programing approach, which have not been addressed in previous works. The numerical studies show the effectiveness of the proposed model

  15. A code for optimising triplet layout

    CERN Document Server

    AUTHOR|(CDS)2141109; Seryi, Andrei; Abelleira, Jose; Cruz Alaniz, Emilia

    2017-01-01

    One of the main challenges when designing final focus systems of particle accelerators is maximising the beam stay clear in the strong quadrupole magnets of the inner triplet. Moreover it is desirable to keep the quadrupoles in the inner triplet as short as possible for space and costs reasons but also to reduce chromaticity and simplify corrections schemes. An algorithm that explores the triplet parameter space to optimise both these aspects was written. It uses thin lenses as a first approximation for a broad parameter scan and MADX for more precise calculations. The thin lens algorithm is significantly faster than a full scan using MADX and relatively precise at indicating the approximate area where the optimum solution lies.

  16. Optimisation of milling parameters using neural network

    Directory of Open Access Journals (Sweden)

    Lipski Jerzy

    2017-01-01

    Full Text Available The purpose of this study was to design and test an intelligent computer software developed with the purpose of increasing average productivity of milling not compromising the design features of the final product. The developed system generates optimal milling parameters based on the extent of tool wear. The introduced optimisation algorithm employs a multilayer model of a milling process developed in the artificial neural network. The input parameters for model training are the following: cutting speed vc, feed per tooth fz and the degree of tool wear measured by means of localised flank wear (VB3. The output parameter is the surface roughness of a machined surface Ra. Since the model in the neural network exhibits good approximation of functional relationships, it was applied to determine optimal milling parameters in changeable tool wear conditions (VB3 and stabilisation of surface roughness parameter Ra. Our solution enables constant control over surface roughness parameters and productivity of milling process after each assessment of tool condition. The recommended parameters, i.e. those which applied in milling ensure desired surface roughness and maximal productivity, are selected from all the parameters generated by the model. The developed software may constitute an expert system supporting a milling machine operator. In addition, the application may be installed on a mobile device (smartphone, connected to a tool wear diagnostics instrument and the machine tool controller in order to supply updated optimal parameters of milling. The presented solution facilitates tool life optimisation and decreasing tool change costs, particularly during prolonged operation.

  17. Feasibility of the use of optimisation techniques to calibrate the models used in a post-closure radiological assessment

    International Nuclear Information System (INIS)

    Laundy, R.S.

    1991-01-01

    This report addresses the feasibility of the use of optimisation techniques to calibrate the models developed for the impact assessment of a radioactive waste repository. The maximum likelihood method for improving parameter estimates is considered in detail, and non-linear optimisation techniques for finding solutions are reviewed. Applications are described for the calibration of groundwater flow, radionuclide transport and biosphere models. (author)

  18. Optimisation of energy absorbing liner for equestrian helmets. Part II: Functionally graded foam liner

    International Nuclear Information System (INIS)

    Cui, L.; Forero Rueda, M.A.; Gilchrist, M.D.

    2009-01-01

    The energy absorbing liner of safety helmets was optimised using finite element modelling. In this present paper, a functionally graded foam (FGF) liner was modelled, while keeping the average liner density the same as in a corresponding reference single uniform density liner model. Use of a functionally graded foam liner would eliminate issues regarding delamination and crack propagation between interfaces of different density layers which could arise in liners with discrete density variations. As in our companion Part I paper [Forero Rueda MA, Cui L, Gilchrist MD. Optimisation of energy absorbing liner for equestrian helmets. Part I: Layered foam liner. Mater Des [submitted for publication

  19. The Inertia Weight Updating Strategies in Particle Swarm Optimisation Based on the Beta Distribution

    Directory of Open Access Journals (Sweden)

    Petr Maca

    2015-01-01

    Full Text Available The presented paper deals with the comparison of selected random updating strategies of inertia weight in particle swarm optimisation. Six versions of particle swarm optimization were analysed on 28 benchmark functions, prepared for the Special Session on Real-Parameter Single Objective Optimisation at CEC2013. The random components of tested inertia weight were generated from Beta distribution with different values of shape parameters. The best analysed PSO version is the multiswarm PSO, which combines two strategies of updating the inertia weight. The first is driven by the temporally varying shape parameters, while the second is based on random control of shape parameters of Beta distribution.

  20. An impact assessment of electricity and emission allowances pricing in optimised expansion planning of power sector portfolios

    International Nuclear Information System (INIS)

    Tolis, Athanasios I.; Rentizelas, Athanasios A.

    2011-01-01

    Highlights: → The impact of electricity and CO 2 allowance pricing in power sector is researched. → A stochastic programming approach without recourse is used for the optimisation. → Higher electricity prices may be proportionally beneficial for the power system. → The CO 2 allowance prices may be inversely proportionate with the expected yields. → High CO 2 allowance prices are inhibitors for conventional technology projects. -- Abstract: The present work concerns a systematic investigation of power sector portfolios through discrete scenarios of electricity and CO 2 allowance prices. The analysis is performed for different prices, from regulated to completely deregulated markets, thus representing different electricity market policies. The modelling approach is based on a stochastic programming algorithm without recourse, used for the optimisation of power sector economics under multiple uncertainties. A sequential quadratic programming routine is applied for the entire investigation period whilst the time-dependent objective function is subject to various social and production constraints, usually confronted in power sectors. The analysis indicated the optimal capacity additions that should be annually ordered from each competitive technology in order to substantially improve both the economy and the sustainability of the system. It is confirmed that higher electricity prices lead to higher financial yields of power production, irrespective of the CO 2 allowance price level. Moreover, by following the proposed licensing planning, a medium-term reduction of CO 2 emissions per MW h by 30% might be possible. Interestingly, the combination of electricity prices subsidisation with high CO 2 allowance prices may provide favourable conditions for investors willing to engage on renewable energy markets.