WorldWideScience

Sample records for europium borides

  1. The electrochemical synthesis of europium boride

    Directory of Open Access Journals (Sweden)

    Bukatova G.A.

    2003-01-01

    Full Text Available The electroreduction of boron, europium and the electrochemical synthesis of europium boride have been investigated in NaCl-KCl-NaF(10 wt. % melt on silver and molybdenum electrodes. The parameters of boron reduction in the chloride-fluoride melt have been obtained and the character of its joint deposition with europium has been studied.

  2. The electrochemical synthesis of europium boride

    OpenAIRE

    Bukatova G.A.; Kuznetsov S.A.; Gaune-Escard M.

    2003-01-01

    The electroreduction of boron, europium and the electrochemical synthesis of europium boride have been investigated in NaCl-KCl-NaF(10 wt. %) melt on silver and molybdenum electrodes. The parameters of boron reduction in the chloride-fluoride melt have been obtained and the character of its joint deposition with europium has been studied.

  3. Analysis of aluminum boride and zirconium boride

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, Yasuo (Institute of Physical and Chemical Research, Wako, Saitama (Japan))

    1982-09-01

    A method for analyzing aluminum and zirconium borides is presented. Decomposition of the borides was achieved in a Uniseal Decomposition Vessel (capacity, 23 ml), in which aluminum boride was heated with (1 + 1) HNO/sub 3/ at 150/sup 0/C for 3 h and zirconium boride with a mixture of (1 + 1) HNO/sub 3/ and (1 + 5) H/sub 2/SO/sub 4/ at the same temperature for 6 h. Aluminum and boron in the solution obtained were separated with cation exchange resin (Dowex 50 WX 8). Boron in the effluent was determined with the titrimetric method using mannite. Aluminum adsorped on the resin was eluted with 2 M HCl and determined by chelatometric titration. Zirconium was separated from boron as zirconium hydroxide by precipitation with NaOH and by filtration with a Nucleopore membrane filter. Boron in the filtrate was determined by the above mentioned method. After dissolution of zirconium hydroxide with HCl, zirconium was precipitated with mandelic acid. The optimum concentration of HCl for the complete precipitation of zirconium mandelate was (2 -- 3) M. The precipitate was filtered on a G 4 glass filter, dried at 110/sup 0/C and weighted as zirconium tetramandelate. The following boride samples were analyzed: Selected crystals of ..cap alpha..-AlB/sub 12/ and ..beta..-AlB/sub 12/, and two ZrB/sub 2/ samples, the one prepared by carbothermic reduction and the other by direct reaction of zirconium and boron.

  4. Kinetics of borided gear steels

    Indian Academy of Sciences (India)

    The boride layer was characterized by optical microscopy, X-ray diffraction technique and microVickers hardness tester. X-ray diffraction analysis of boride layers on the surface of the steels revealed the existence of FeB, Fe2B, CrB and Cr2B compounds. The thickness of the boride layer increases by increasing boriding ...

  5. Kinetics of borided gear steels

    Indian Academy of Sciences (India)

    source used, boriding temperature, treatment time, and properties of the borided material (Sahin. & Meric 2002 ... The boriding heat treatment was carried out in solid medium containing an Ekabor-II ..... 2007 Growth kinetics of boride layers on iron-chromium alloys and their dry abrasive wear resistance,. Materials Science ...

  6. An investigation on borided AISI 1020 steel

    Science.gov (United States)

    Altinsoy, I.; Efe, F. G. Celebi; Ipek, M.; Ozbek, I.; Zeytin, S.; Bindal, C.

    2013-12-01

    In this study, we investigated some properties of borided AISI 1020 steel. Boronizing heat treatment was carried out at 800°C, 875°C and 950°C for 2, 4, 6 and 8 h using Ekabor 1 powders. The hardness of borides formed on the steel substrate measured via Vickers indenter was about 1500 HVN. The thickness of boride layers depending on the process temperature and time was ranged from 20.5 to 216 μm. The presence of Fe2B boride was determined by XRD analysis. SEM microscope studies showed that the borides formed on the AISI 1020 steel have columnar nature. Kinetics studies reveal a parabolic relationship between layer depth and process time, and the activation energy is calculated as 164,356 kJ/mol. Moreover, an attempt was made to investigate the possibility of predicting the iso-thickness of boride layer and to establish an empirical relationship between process parameters of boriding and boride layer for industrial applications.

  7. Characterization of AISI 4140 borided steels

    Energy Technology Data Exchange (ETDEWEB)

    Campos-Silva, I., E-mail: icampos@ipn.mx [Instituto Politecnico Nacional, Grupo Ingenieria de Superficies, SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F., 07738 (Mexico); Ortiz-Dominguez, M.; Lopez-Perrusquia, N.; Meneses-Amador, A. [Instituto Politecnico Nacional, Grupo Ingenieria de Superficies, SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F., 07738 (Mexico); Escobar-Galindo, R. [Instituto de Ciencia de Materiales de Madrid (CSIC), E-28049 Cantoblanco, Madrid (Spain); Martinez-Trinidad, J. [Instituto Politecnico Nacional, Grupo Ingenieria de Superficies, SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F., 07738 (Mexico)

    2010-02-01

    The present study characterizes the surface of AISI 4140 steels exposed to the paste-boriding process. The formation of Fe{sub 2}B hard coatings was obtained in the temperature range 1123-1273 K with different exposure times, using a 4 mm thick layer of boron carbide paste over the material surface. First, the growth kinetics of boride layers at the surface of AISI 4140 steels was evaluated. Second, the presence and distribution of alloying elements on the Fe{sub 2}B phase was measured using the Glow Discharge Optical Emission Spectrometry (GDOES) technique. Further, thermal residual stresses produced on the borided phase were evaluated by X-ray diffraction (XRD) analysis. The fracture toughness of the iron boride layer of the AISI 4140 borided steels was estimated using a Vickers microindentation induced-fracture testing at a constant distance of 25 {mu}m from the surface. The force criterion of fracture toughness was determined from the extent of brittle cracks, both parallel and perpendicular to the surface, originating at the tips of an indenter impression. The fracture toughness values obtained by the Palmqvist crack model are expressed in the form K{sub C}({pi}/2) > K{sub C} > K{sub C}(0) for the different applied loads and experimental parameters of the boriding process.

  8. Fluorescent Europium Chelate Stain

    Science.gov (United States)

    Scaff, W. L.; Dyer, D. L.; Mori, K.

    1969-01-01

    The europium chelate of 4,4,4-trifluoro-1-(2-thienyl)-1,3-butanedione (thenoyl-trifluoroacetone; TTA) is firmly bound to microorganisms. It fluoresces brightly at 613 nm with activation at 340 nm. Cells may be stained with 10−3m chelate in 50% ethyl alcohol, followed by washing with 50% ethyl alcohol. Equal or better stains are produced with 10−3m aqueous europium salt, water wash, and 10−2m aqueous TTA. A noncomplexing buffer should be used to maintain the pH at 6.5 to 6.8. Images PMID:4181107

  9. Characterization of rough interfaces obtained by boriding

    Energy Technology Data Exchange (ETDEWEB)

    Campos-Silva, I. [Instituto Politecnico Nacional, SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico)], E-mail: icampos@ipn.mx; Balankin, A.S. [Instituto Politecnico Nacional, SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico); Sierra, A.H. [Instituto Politecnico Nacional, UPIICSA, Av. Te 950, Col Granjas, Mexico D.F. 08400 (Mexico); Lopez-Perrusquia, N. [Instituto Politecnico Nacional, SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico); Escobar-Galindo, R. [Instituto de Ciencia de Materiales de Madrid (CSIC), Cantoblanco, Madrid E-28049 (Spain); Morales-Matamoros, D. [Instituto Mexicano del Petroleo, Eje Lazaro Cardenas Norte, Mexico D.F. 07738 (Mexico)

    2008-12-30

    This study evaluates the morphology of borided interfaces by means of the fractal theory. The boride layers were formed in the AISI M2 steel by applying the paste boriding treatment at temperatures of 1253 and 1273 K and treatment times of 2 and 6 h, while a boron carbide paste thickness of 4 or 5 mm covered the samples surface in order to produce the boron diffusion. The morphology of interfaces formed between FeB and Fe{sub 2}B layers and between Fe{sub 2}B layer and steel substrate was analyzed by the rescaled-range (R/S), root-mean-square (RMS), and Fourier power spectrum (FPS) methods. Moreover, the multi-affine spectra of roughness exponent were obtained by calculating the q-order height-height correlation functions. We found that both interfaces are multi-affine, rather than self-affine. The multi-affine spectra of roughness exponents are found to be different for FeB/Fe{sub 2}B and Fe{sub 2}B/substrate interfaces, but independent on the treatment parameters (boron carbide paste thickness, temperature, and boriding time). Furthermore, we found that the multi-affine spectra of both interfaces behave as it is expected for 'universal multi-fractals' with the Levy index {gamma} = 1, associated with the multiplicative cascades with a log-Cauchy distribution. Furthermore, our data suggest a great homogeneity of the boron diffusion field, characterized by universal fractal dimension D{sub diff} = 2.90 {+-} 0.01. These findings provide a novel insight into the nature of phase formation during the boriding treatment.

  10. Boriding of binary Ni-Ti shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ucar, Nazim; Dogan, Sule [Suleyman Demirel Univ., Isparta (Turkey). Physics Dept.; Karakas, Mustafa Serdar [Cankaya Univ., Ankara (Turkey). Materials Science and Engineering Dept.; Calik, Adnan [Suleyman Demirel Univ., Isparta (Turkey). Manufacturing Engineering Dept.

    2016-07-01

    Boriding of binary Ni-Ti shape memory alloys was carried out in a solid medium at 1273 K for 2, 4, 6, and 8 h using the powder pack method with proprietary Ekabor-Ni powders. Characterization of the boride layer formed on the surface of alloys was done by optical microscopy and scanning electron microscopy. The presence of boride, silicide, and borosilicide phases in the boride layers was confirmed by X-ray diffraction analysis. The thickness and microhardness of the boride layers increased with increasing boriding time. Hardness profiles showed a rapid decrease in hardness moving from the boride layer to the main structure. The high hardness of the boride layer was attributed mainly to the formation of TiB{sub 2}. A parabolic relationship was observed between layer thickness and boriding time, and the growth rate constant for the boriding treatment was calculated as 0.62 x 10{sup -8} cm{sup 2}s{sup -1}.

  11. Fracture Microindentation on boride layers on AISI 1020 steel

    Science.gov (United States)

    Prince, M.; Thanu, A. Justin; Arjun, S. L.; Velmurugan, U.; Gopalakrishnan, P.

    2016-02-01

    In this paper, an attempt has been made to enhance the fracture toughness (Kc) of boride layer using multi-component (Ni, Cr and B) laser bonding. The fracture toughness of continuously pack borided, interrupted pack borided and multi-component (Ni, Cr and B) laser borided steel specimens was measured using Vickers microindentation fracture toughness test as per ASTM E384 standard. The fracture toughness of continuously pack borided layer was - 3.3 MPa.m1/2. The fracture toughness of interrupted boride layer was in the range of - 4.9 MPa.m1/2. The fracture toughness of multi-component (Ni, Cr and B) laser borided layer was in the range of 13.8 - 18.3 MPa.m1/2. A significant improvement in fracture toughness of laser treated specimens was observed from the experimental results. This may be due to better distribution of boron, nickel, chromium and other alloying elements due to laser treatment and relatively more uniform boride layer as compared with continuously pack borided layer and interrupted pack borided layer.

  12. Investigation of the diffusion kinetics of borided stainless steels

    Science.gov (United States)

    Kayali, Yusuf

    2013-12-01

    In this study, the kinetics of borides formed on AISI 420, AISI 304 and AISI 304L stainless steels was investigated. Boronizing treatment was carried out using Ekabor-II powders at the processing temperatures of 1123, 1173 and 1223 K for 2, 4 and 6 h. The phases of the boride layers of borided AISI 420, AISI 304 and AISI 304L stainless steels were FeB, Fe2B, CrB and NiB, respectively. The thickness of the boride layer formed on the borided steels ranged from 4.6 to 64 μm depending on the boriding temperature, boriding time and alloying elements of the stainless steels. Depending on the chemical composition, temperature and layer thickness, the activation energies of boron in AISI 420, AISI 304 and AISI 304L stainless steels were found to be 206.161, 234.641 and 222.818 kJ/mol, respectively. The kinetics of growth of the boride layers formed on the AISI 420, AISI 304 and AISI 304L stainless steels and the thickness of the boride layers were investigated.

  13. Preparation of single phase molybdenum boride

    Energy Technology Data Exchange (ETDEWEB)

    Camurlu, Hasan Erdem, E-mail: erdemcamurlu@gmail.com [Akdeniz University, Mechanical Engineering Department, 07058, Antalya (Turkey)

    2011-04-28

    Highlights: > Formation of Mo and a mixture of molybdenum boride phases take place in preparation of molybdenum borides. > It is intricate to prepare single phase molybdenum borides. > Formation of single phase MoB from MoO{sub 3} + B{sub 2}O{sub 3} + Mg mixtures has not been reported previously. > Single phase MoB was successfully prepared through a combination of mechanochemical synthesis and annealing process. - Abstract: The formation of MoB through volume combustion synthesis (VCS), and through mechanochemical synthesis (MCS) followed by annealing has been investigated. MoO{sub 3}, B{sub 2}O{sub 3} and Mg were used as reactants while MgO and NaCl were introduced as diluents. Products were leached in dilute HCl solution and were subjected to X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) examinations. Mo was the major phase component in the VCS products under all the experimental conditions. Mo{sub 2}B, MoB, MoB{sub 2} and Mo{sub 2}B{sub 5} were found as minor phases. Products of MCS contained a mixture of Mo{sub 2}B, MoB, MoB{sub 2} and Mo. After annealing the MCS product at 1400 deg. C for 3 h, single phase {alpha}-MoB was obtained.

  14. Growth kinetics of boride coatings formed at the surface AISI M2 during dehydrated paste pack boriding

    Energy Technology Data Exchange (ETDEWEB)

    Doñu Ruiz, M.A., E-mail: mdonur0800@alumno.ipn.mx [Universidad Politécnica del Valle de México UPVM, Grupo Ciencia e Ingeniería de Materiales, Av. Mexiquense S/N Esquina Av. Universidad Politécnica, Col Villa Esmeralda, 54910 Tultitlan (Mexico); López Perrusquia, N.; Sánchez Huerta, D. [Universidad Politécnica del Valle de México UPVM, Grupo Ciencia e Ingeniería de Materiales, Av. Mexiquense S/N Esquina Av. Universidad Politécnica, Col Villa Esmeralda, 54910 Tultitlan (Mexico); Torres San Miguel, C.R.; Urriolagoitia Calderón, G.M. [Instituto Politécnico Nacional, SEPI-ESIME, Unidad Profesional Adolfo López Mateos Zacatenco, Edificio 5, 2do. Piso, Col. Lindavista, CP 07738 México, D.F. (Mexico); Cerillo Moreno, E.A. [Universidad Politécnica del Valle de México UPVM, Grupo Ciencia e Ingeniería de Materiales, Av. Mexiquense S/N Esquina Av. Universidad Politécnica, Col Villa Esmeralda, 54910 Tultitlan (Mexico); Cortes Suarez, J.V. [Univerisdad Autónoma Metropolitana Unidad Azcapotzalco, Av. San Pablo 180 Azcapotzalco 02200, Área de Ciencia de los Materiales, México, D.F. (Mexico)

    2015-12-01

    The growth kinetics of the boride coatings (FeB and Fe{sub 2}B) at the surface of AISI M2 high speed steels were studied in this work. Boriding thermochemical treatment was carried out by dehydrated paste pack at three different temperatures 1173, 1223, and 1273 K and four exposure times 1, 3, 5, and 7 h, respectively. The presence of FeB and Fe{sub 2}B phases was identified by scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction method. In order to obtain the boron diffusion coefficients at the FeB/Fe{sub 2}B boride coatings, a mathematical model based on the mass balance at the growing interfaces was proposed under certain assumptions. Likewise the parabolic growth constants and the boride incubation time were established as a function of the parameters η (T) and ε (T). The activation energy values estimated for the FeB and Fe{sub 2}B layers were 233.42 and 211.89 kJ mol{sup −1} respectively. A good agreement was obtained between the simulated values of boride layer thicknesses and the experimental results. Finally, empirical relationships of boride coating thickness as a function of boriding temperature and time are presented. - Highlights: • Formed boride coatings at the surface of AISI M2 high speed steels by new process dehydrated paste pack boriding. • The model was based on the mass balance equation at the FeB/Fe{sub 2}B and Fe{sub 2}B/Fe interfaces by considering the boride incubation time. • A good agreement was obtained between the simulated values of boride layers coatings and the experimental results.

  15. Europium-155 in Debris from Nuclear Weapons

    DEFF Research Database (Denmark)

    Aarkrog, Asker; Lippert, Jørgen Emil

    1967-01-01

    The lithium-drifted germanium detector enables determination of europium-155 on a routine basis in environmental samples contaminated with debris from nuclear weapons. From measurements of europium-155, cesium-144, and strontium-90 in air filters collected between 1961 and 1966, the yield...... of europium-155 from weapons was estimated at 1400 atoms per 10$^{6}$ fissions, which is close to the yield of europium-155 from fast fission of uranium-238....

  16. Carbide and boride laser modification of steels

    Science.gov (United States)

    Major, Boguslaw; Ebner, Reinhold

    1997-10-01

    Microstructure modification by laser remelting or laser alloying was studied on carbon Ck45 and high speed steels. Laser remelting of Ck45 by overlapping laser tracks led to a great refinement of martensitic structure, especially in the heat affected zone of subsequent laser track. High speed steel (HSS) M2 after laser remelting showed, beside the tetragonal martensite, the diffraction lines of cubic carbides of the M6C and M12C types. Laser alloying of M2 HSS using vanadium carbide (VC) additions caused increasing of eutectic in the interdendritic space, which was accompanied with reduction of the M6C and rising of the MC. M2 HSS laser alloyed with molybdenum carbide (Mo2C) showed formation of the M6C for the hipereutectic compositions while at the highest concentrations of molybdenum, primary dendrites of the M2C and stabilized ferrite were stated. High additions of borides: CrB or VB2; developed formation of the primary borides of blocky type containing a high amount of W, Cr or W, V, respectively. Laser alloying of Ck45 by means of: CrB, VB2 and B4C showed: in the case of CrB an eutectic (alpha) '/M3(C,B)/M2B as well as primary precipitates of the M2B phase for hipereutectic compositions; by adding VB2, the M3B2 and M2B phases were identified experimentally for hipereutectic concentrations; for alloying using B4C, the cellular dendritic structure together with primary borides of the (tau) -M23(C,B)6 phase were stated for hipereutectic compositions. The phase diagrams of M2 HSS + (VC or Mo2C) as well as Ck45 + B4C systems were calculated to predict changes of the constitutions due to laser alloying. Comparison of the solidification structures established experimentally with the calculated phase diagrams revealed a good correlation for the carbides, especially.

  17. Effect of boron paste thickness on the growth kinetics of polyphase boride coatings during the boriding process

    Energy Technology Data Exchange (ETDEWEB)

    Campos, I. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Mechanical Department, Calle del Puente 222 Col., Ejidos de Huipulco, Mexico, DF 14380 (Mexico)]. E-mail: ivan.campos@itesm.mx; Torres, R. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Mechanical Department, Calle del Puente 222 Col., Ejidos de Huipulco, Mexico, DF 14380 (Mexico); Bautista, O. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Mechanical Department, Calle del Puente 222 Col., Ejidos de Huipulco, Mexico, DF 14380 (Mexico); Ramirez, G. [IPN-SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico, DF 07738 (Mexico); Zuniga, L. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Mechanical Department, Calle del Puente 222 Col., Ejidos de Huipulco, Mexico, DF 14380 (Mexico)

    2006-01-15

    The growth kinetics of FeB and Fe{sub 2}B phases forming on AISI M2 steel by paste boriding was studied using different values of paste thickness, treating temperature and exposure time. The growth of iron boride layers is described by the mass balance equation between phases in thermodynamic equilibrium, assuming that the boron concentration at the interfaces remain constant during the treatment. The experimental results show that boron mobility and growth kinetics of iron borides are considerably increased when the paste thickness is increased at constant values of temperature and exposure time.

  18. Investigation of diffusion kinetics of plasma paste borided AISI 8620 ...

    Indian Academy of Sciences (India)

    Abstract. In the present study, AISI 8620 steel was plasma paste borided by using various B2O3 paste mixture. The plasma paste boriding process was carried out in a dc plasma system at temperatures of 973, 1023 and 1073 K for 2, 5 and 7 h in a gas mixture of 70% H2 -30% Ar under a constant pressure of 10 mbar.

  19. Investigation of diffusion kinetics of plasma paste borided AISI 8620 ...

    Indian Academy of Sciences (India)

    ... diffraction, Vickers micro-hardness tester and the growth kinetics of the boride layers. X-ray diffraction analysis of boride layers on the surface of the steel revealed FeB and Fe2B phases. Depending on temperature and layer thickness, the activation energies of boron in steel were found to be 124.7 kJ/mol for 100% B2O3.

  20. Binary and Ternary Explorations of the Molybdenum Boride System

    OpenAIRE

    Dismukes, Avalon Hope

    2015-01-01

    Refractory metal borides have recently generated intense interest in materials chemistry. These compounds have been shown to possess many advantageous properties, such as exceptionally high hardness, electrical conductivity, and even superconductivity. Higher molybdenum borides are discussed as compounds of interest in this category of materials. However, the complex phase relationships in the molybdenum-boron system complicate the preparation of phase-pure samples. MoB2 and Mo2B4 have both b...

  1. PECULIARITIES OF BORIDE COATING FORMATION MADE OF COMPOSITE METAL-THERMAL POWDER MEDIA

    Directory of Open Access Journals (Sweden)

    N. A. Galynskaya

    2011-01-01

    Full Text Available The paper has investigated an influence of compositions pertaining to complex powder metal-thermal saturating media for boriding on phase-, structure formation and properties of boride coatings in respect of carbon steel.

  2. Characterisation of Wear Resistant Boride Layers on a Tool Steel by Activity Controlled Pack Boronising

    DEFF Research Database (Denmark)

    Fernandes, Frederico Augusto Pires; Christiansen, Thomas Lundin; Somers, Marcel A. J.

    2015-01-01

    The present work addresses the production and characterisation of iron boride layers by pack boronising of a Vanadis 6 tool steel. The boride layers were produced at 900°C for 2h using different pack compositions in order to obtain a single-phase boride layer. The layers were characterized by ele...

  3. The characterization of boride layer on the St37 iron

    Science.gov (United States)

    Sutrisno, Soegijono, Bambang

    2012-06-01

    The property such as microhardness of boride layer formed on St37 iron was investigated. Boronizing was carried out in a solid medium consisting of nano size powders of 50% B4C as a donor, 45% SiC as a diluent, and 5% KBF4 as an activator treated at the temperature of 1000°C for 8 hours. The phases that were formed on the substrate was found as Fe2B and FeB layer that had smooth and flate shape morphology. The hardness of boride layer on St37 was over 2000 HV, while the hardness of untreated St37 iron was about 123,82 HV. Depending on process time and temperature, the depth of boride layer ranges from 20 to 60 μm, leading to a diffusion controlled process.

  4. Corrosion behavior of boride layers evaluated by the EIS technique

    Energy Technology Data Exchange (ETDEWEB)

    Campos, I. [Instituto Politecnico Nacional. SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico)], E-mail: icampos@ipn.mx; Palomar-Pardave, M. [Universidad Autonoma Metropolitana-Azcapotzalco, Materials Department, Avenue San Pablo 180 Col. Reynosa Tamaulipas, Mexico D.F. 02200 (Mexico); Amador, A. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico); VillaVelazquez, C. [Instituto Politecnico Nacional. SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico); Hadad, J. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico)

    2007-09-30

    The corrosion behavior of boride layers at the AISI 304 steel surface is evaluated in the present study. Electrochemical impedance spectroscopy (EIS) technique was used for the evaluation of the polarization resistance at the steel surface, with the aid of AUTOLAB potentiostat. Samples were treated with boron paste thickness of 4 and 5 mm, in the range of temperatures 1123 {<=} T {<=} 1273 K and exposed time of 4 and 6 h. The electrochemical technique employed 10 mV AC with a frequency scan range from 8 kHz to 3 mHz in deaerated 0.1 M NaCl solution. Nyquist diagrams show that the highest values of corrosion resistance are present in the samples borided at the temperature of 1273 K, with treatment time of 4 h and 4 mm of boron paste thickness. The values of corrosion resistance on borided steels are compared with the porosity exhibited in the layers.

  5. Laser borided composite layer produced on austenitic 316L steel

    Directory of Open Access Journals (Sweden)

    Mikołajczak Daria

    2016-12-01

    Full Text Available Abstract Austenitic 316L steel is well-known for its good resistance to corrosion and oxidation. Therefore, this material is often used wherever corrosive media or high temperatures are to be expected. The main drawback of this material is very low hardness and low resistance to mechanical wear. In this study, the laser boriding was used in order to improve the wear behavior of this material. As a consequence, a composite surface layer was produced. The microstructure of laser-borided steel was characterized by only two zones: re-melted zone and base material. In the re-melted zone, a composite microstructure, consisting of hard ceramic phases (borides and a soft austenitic matrix, was observed. A significant increase in hardness and wear resistance of such a layer was obtained.

  6. Liposome Biodistribution via Europium Complexes.

    Science.gov (United States)

    Mignet, Nathalie; Scherman, Daniel

    2017-01-01

    The drug delivery field needs tools to follow vector biodistribution. Radioactive tracers and conventional fluorophores are widely used. We propose here to use europium complexes. Use of pulsed light source time-resolved fluorimetry takes into account the fluorescence decay time of the lanthanide chelates to gain sensitivity in biological media. The method was developed to follow liposome biodistribution. Octadecyl-DTPA.Eu compound has been prepared and incorporated into liposomes without alteration of its fluorescence signal. The method has been validated by comparison with fluorophore-labeled liposomes. The way to proceed to use this method for liposomes or other vectors is detailed.

  7. Pulsed nanocrystalline plasma electrolytic boriding as a novel ...

    Indian Academy of Sciences (India)

    WINTEC

    of the porous complex titanium borided layer. Large val- ues of polarization resistance (Rp) are also noted in all the samples. A high Rp value is an indication of the working electrode strongly resisting change from its equilibrium state and corresponds to a low rate of titanium ion re- lease. This behaviour is clearly noted and ...

  8. Pulsed nanocrystalline plasma electrolytic boriding as a novel ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 30; Issue 6. Pulsed nanocrystalline plasma electrolytic boriding as a novel method for corrosion protection of CP-Ti (Part 1: Different frequency and duty cycle). M Kh Aliev A Saboor. Alloys and Steels Volume 30 Issue 6 December 2007 pp 601-605 ...

  9. Equilibrium And Growth Morphologies Of Trinickel Boride Ni3b ...

    African Journals Online (AJOL)

    The morphology of the trinickel boride Ni3B precipitates during slow cooling in differential thermal analysis (DTA) has been investigated using high resolution electron microscopy (HREM). Due to the large development of the facets of the type {022}, the crystal tends towards an equilibrium morphology whereas the growth ...

  10. Resonance ionization scheme development for europium

    CERN Document Server

    Chrysalidis, K; Fedosseev, V N; Marsh, B A; Naubereit, P; Rothe, S; Seiffert, C; Kron, T; Wendt, K

    2017-01-01

    Odd-parity autoionizing states of europium have been investigated by resonance ionization spectroscopy via two-step, two-resonance excitations. The aim of this work was to establish ionization schemes specifically suited for europium ion beam production using the ISOLDE Resonance Ionization Laser Ion Source (RILIS). 13 new RILIS-compatible ionization schemes are proposed. The scheme development was the first application of the Photo Ionization Spectroscopy Apparatus (PISA) which has recently been integrated into the RILIS setup.

  11. Resonance ionization scheme development for europium

    Energy Technology Data Exchange (ETDEWEB)

    Chrysalidis, K., E-mail: katerina.chrysalidis@cern.ch; Goodacre, T. Day; Fedosseev, V. N.; Marsh, B. A. [CERN (Switzerland); Naubereit, P. [Johannes Gutenberg-Universität, Institiut für Physik (Germany); Rothe, S.; Seiffert, C. [CERN (Switzerland); Kron, T.; Wendt, K. [Johannes Gutenberg-Universität, Institiut für Physik (Germany)

    2017-11-15

    Odd-parity autoionizing states of europium have been investigated by resonance ionization spectroscopy via two-step, two-resonance excitations. The aim of this work was to establish ionization schemes specifically suited for europium ion beam production using the ISOLDE Resonance Ionization Laser Ion Source (RILIS). 13 new RILIS-compatible ionization schemes are proposed. The scheme development was the first application of the Photo Ionization Spectroscopy Apparatus (PISA) which has recently been integrated into the RILIS setup.

  12. Growth kinetics of boride layers formed on 99.0% purity nickel

    Indian Academy of Sciences (India)

    The boride layer was characterized by optical microscopy, X-ray diffraction technique and micro-Vickers hardness tester. X-ray diffraction analysis revealed the existence of NiB, Ni2B, Ni3B and Ni4B3 compounds at the surface of borided Nickel 201 alloy. The thickness of the boride layer increased with an increase in the ...

  13. Hard Surface Layers by Pack Boriding and Gaseous Thermo-Reactive Deposition and Diffusion Treatments

    DEFF Research Database (Denmark)

    Christiansen, Thomas Lundin; Bottoli, Federico; Dahl, Kristian Vinter

    2017-01-01

    Thermo-reactive deposition and diffusion (TRD) and boriding are thermochemical processes that result in very high surface hardness by conversion of the surface into carbides/nitrides and borides, respectively. These treatments offer significant advantages in terms of hardness, adhesion, tribo......-based borides. The obtained surface layers were characterized with X-ray diffraction, scanning electron microscopy, reflected light microscopy, and micro-indentation....

  14. Fracture Toughness of Thick Boride Layers Estimated by the Cross-Sectioned Scratch Test

    Science.gov (United States)

    Campos-Silva, I.; Flores-Jiménez, M.; Bravo-Bárcenas, D.; Rodríguez-Castro, G.; Martínez-Trinidad, J.; Meneses-Amador, A.

    2018-01-01

    New results about the fracture toughness (K c) of thick boride layers estimated by the cross-sectioned scratch test are presented in this study. The FeB-Fe2B layers developed at the surface of borided AISI 1018 and AISI 1045 steels and the Fe2B layer formed on the borided AISI 1045 steel exposed to a diffusion annealing process (DAP) were used for this purpose. The cross-sectioned scratch tests were performed with a Vickers diamond stylus drawn across the thick boride layer under a constant load to produce a half-cone-shaped fracture near to the top surface of the borided steels. The height of the half-cone-shaped fracture as a function of the cross-sectioned scratch loads was used to determine the fracture toughness of the FeB and Fe2B layers. The results showed a fracture resistance of ˜2.8 {MPa}√ m for the FeB layer formed at the surface of borided AISI 1045 steel. Likewise, the effect of the DAP on the surface of the borided AISI 1045 steel promoted the formation of an exclusively Fe2B layer, with an increase in the fracture toughness of the whole boride layer around 5 {MPa}√ m . Finally, the principle of the technique can be used to minimize the influence of the anisotropic properties on the fracture toughness along the depth of boride layers.

  15. Electronic state of europium atoms on surface of oxidized tungsten

    CERN Document Server

    Davydov, S Y

    2001-01-01

    The energy scheme of the europium atoms adsorption system on the tungsten surface, coated with the oxygen monolayer, is considered. The evaluations of the europium adatoms charged state on the oxidized tungsten surface are performed. It is established, that europium, adsorbed at the oxidized tungsten surface, is a positive ion with the charge close to the unit. The zonal scheme of the Eu-O/W adsorption system for the europium low and high concentrations is proposed

  16. Europium anomaly in plagioclase feldspar - Experimental results and semiquantitative model.

    Science.gov (United States)

    Weill, D. F.; Drake, M. J.

    1973-01-01

    The partition of europium between plagioclase feldspar and magmatic liquid is considered in terms of the distribution coefficients for divalent and trivalent europium. A model equation is derived giving the europium anomaly in plagioclase as a function of temperature and oxygen fugacity. The model explains europium anomalies in plagioclase synthesized under controlled laboratory conditions as well as the variations of the anomaly observed in natural terrestrial and extraterrestrial igneous rocks.

  17. Fermi Surface and Antiferromagnetism in Europium Metal

    DEFF Research Database (Denmark)

    Andersen, O. Krogh; Loucks, T. L.

    1968-01-01

    We have calculated the Fermi surface of europium in order to find those features which determine the wave vector of the helical moment arrangement below the Néel point. We find that there are two pieces of Fermi surface: an electron surface at the symmetry point H, which has the shape of rounded...... of the nearly cubical part of the hole surface at P, and we also discuss the effects of the electron surface at H. Since it is likely that barium and europium have similar Fermi surfaces, we have presented several extremal areas and the corresponding de Haas-van Alphen frequencies in the hope that experimental...

  18. Organophosphate Nerve Agent Detection with Europium Complexes

    Directory of Open Access Journals (Sweden)

    Jake R. Schwierking

    2004-01-01

    Full Text Available We explore the detection of paraoxon, a model compound for nonvolatile organophosphate nerve agents such as VX. The detection utilizes europium complexes with 1,10 phenanthroline and thenoyltrifluoroacetone as sensitizing ligands. Both europium luminescence quenching and luminescence enhancement modalities are involved in the detection, which is simple, rapid, and sensitive. It is adaptable as well to the more volatile fluorophosphate nerve agents. It involves nothing more than visual luminescence observation under sample illumination by an ordinary hand-held ultraviolet lamp.

  19. Characterization and diffusion model for the titanium boride layers formed on the Ti6Al4V alloy by plasma paste boriding

    Science.gov (United States)

    Keddam, Mourad; Taktak, Sukru

    2017-03-01

    The present study is focused on the estimation of activation energy of boron in the plasma paste borided Ti6Al4V alloy, which is extensively used in technological applications, using an analytical diffusion model. Titanium boride layers were successfully produced by plasma paste boriding method on the Ti6Al4V alloy in the temperature range of 973-1073 K for a treatment time ranging from 3 to 7 h. The presence of both TiB2 top-layer and TiB whiskers sub-layer was confirmed by the XRD analysis and SEM observations. The surface hardness of the borided alloy was evaluated using Micro-Knoop indenter. The formation rates of the TiB2 and TiB layers were found to have a parabolic character at all applied process temperatures. A diffusion model was suggested to estimate the boron diffusivities in TiB2 and TiB layers under certain assumptions, by considering the effect of boride incubation times. Basing on own experimental data on boriding kinetics, the activation energies of boron in TiB2 and TiB phases were estimated as 136.24 ± 0.5 and 63.76 ± 0.5 kJ mol-1, respectively. Finally, the obtained values of boron activation energies for Ti6Al4V alloy were compared with the data available in the literature.

  20. Transition metal borides. Synthesis, characterization and superconducting properties

    Energy Technology Data Exchange (ETDEWEB)

    Kayhan, Mehmet

    2013-07-12

    A systematic study was done on the synthesis and superconducting properties of metal rich transition metal borides. Five different binary systems were investigated including the boride systems of niobium, tantalum, molybdenum, tungsten and rhenium. High temperature solid state methods were used in order to synthesize samples of different transition metal borides of the composition M{sub 2}B, MB, M{sub 3}B{sub 2}, MB{sub 2}, and M{sub 2}B{sub 4}. The reactions were carried out in three different furnaces with different sample containers: the electric arc (copper crucible), the high frequency induction furnace (boron nitride, tantalum or glassy carbon crucibles), and the conventional tube furnace (sealed evacuated quartz ampoules). The products obtained were characterized with X-ray powder diffractometry, scanning electron microscopy and energy-dispersive X-ray spectroscopy. Phase analyses and crystal structure refinements using the Rietveld method and based on structure models known from literature were performed. A neutron diffraction measurement was done for W{sub 2}B{sub 4} to allow for a complete crystal structure determination, because of the presence of a heavy element like tungsten and a light element like boron that made it difficult to determine the accurate determination of the boron atom positions and occupancies from X-ray data. A new structure model for W{sub 2}B{sub 4} was proposed. Magnetic measurements in a SQUID magnetometer down to temperatures as low as 1.8 K were performed to several of the products in order to see if the transition metal borides become superconducting at low temperatures, and the results were compared with data from literature. Superconducting properties were found for the following compounds: NbB{sub 2} (T{sub C} = 3.5 K), β-MoB (T{sub C} = 2.4 K), β-WB (T{sub C} = 2.0 K), α-WB (T{sub C} = 4.3 K), W{sub 2}B{sub 4} (T{sub C} = 5.4 K), Re{sub 7}B{sub 3} (T{sub C} = 2.4 K). A relationship between the superconducting properties

  1. Effect of Fe2B boride orientation on abrasion wear resistance of Fe-B cast alloy

    Directory of Open Access Journals (Sweden)

    Da-wei Yi

    2017-07-01

    Full Text Available The microstructures and abrasion wear resistance of directional solidification Fe-B alloy have been investigated using optical microscopy, X-ray diffraction, scanning electron microscopy and laser scanning microscopy. The results show that the microstructure of as-cast Fe-B alloy consists of ferrite, pearlite and eutectic boride. After heat treatment, the microstructure is composed of boride and martensite. The plane which is perpendicular to the boride growth direction possesses the highest hardness. In two-body abrasive wear tests, the silicon carbide abrasive can cut the boride and martensite matrix synchronously, and the wear mechanism is micro cutting mechanism. The worn surface roughness and the wear weight loss both increase with the increasing contact load. Moreover, when the boride growth direction is perpendicular to the worn surface, the highest hardness plane of the boride can effectively oppose abrasion, and the martensite matrix can surround and support borides perfectly.

  2. Electron momentum distribution and electronic response of ceramic borides

    Energy Technology Data Exchange (ETDEWEB)

    Heda, N.L. [Department of Pure and Applied Physics, University of Kota, Kota 324005 (India); Meena, B.S.; Mund, H.S. [Department of Physics, Mohanlal Sukhadia University, Udaipur 313001 (India); Sahariya, Jagrati [Department of Physics, Manipal University, Jaipur 303007 (India); Kumar, Kishor [Department of Physics, Mohanlal Sukhadia University, Udaipur 313001 (India); Ahuja, B.L., E-mail: blahuja@yahoo.com [Department of Physics, Mohanlal Sukhadia University, Udaipur 313001 (India)

    2017-03-15

    Isotropic Compton profiles of transition metal based ceramics TaB and VB have been measured using {sup 137}Cs (661.65 keV) γ-ray Compton spectrometer. The experimental momentum densities are compared with those deduced using linear combination of atomic orbitals (LCAO) with Hartree-Fock (HF), density functional theory (DFT) with Wu-Cohen generalized gradient approximation (WCGGA) and also the hybridization of HF and DFT (namely B3PW and PBE0) schemes. It is found that LCAO-DFT-WCGGA scheme based profiles give an overall better agreement with the experimental data, for both the borides. In addition, we have computed the Mulliken's population (MP) charge transfer data, energy bands, density of states and Fermi surface topology of both the borides using full potential-linearized augmented plane wave (FP-LAPW) and LCAO methods with DFT-WCGGA scheme. Cross-overs of Fermi level by the energy bands corresponding to B-2p and valence d-states of transition metals lead to metallic character in both the compounds. Equal-valence-electron-density profiles and MP analysis suggest more ionic character of VB than that of TaB.

  3. New route toward nanosized crystalline metal borides with tuneable stoichiometry and variable morphologies

    OpenAIRE

    Gouget, Guillaume; Beaunier, Patricia; Portehault, David; Sanchez, Clément

    2016-01-01

    International audience; Herein we highlight for the first time the ability to tune the stoichiometry of metal boride nanocrystals through nanoparticle synthesis in thermally stable inorganic molten salts. Two metal-boron systems are chosen as case studies: boron-poor nickel borides and boron-rich yttrium borides. We show that NiB, Ni4B3, Ni2B, Ni3B, and YB6 particles can be obtained as crystalline phases with good selectivity. Anisotropic crystallization is observed in two cases: the first bo...

  4. Phase composition and crack resistance of alloy boride layers on steel

    Science.gov (United States)

    Kholin, A. S.

    1999-04-01

    Alloying of boride layers on steel changes their phase composition, morphology, and structure. Chromium and manganese diminish the fraction of the eutectic in the layer. B-Cr and B-Mn coats do not contain monoborides. B, B-Mo, and B-Mo-W coats consist of two layers, i.e., monoborides and diborides. The other studied coats are represented by a diboride with inclusions of a monoboride. Molybdenum intensifies the texture of the FeB boride as compared with a purely boride layer; the other elements weaken it considerably.

  5. In Situ Solid-Gas Reactivity of Nanoscaled Metal Borides from Molten Salt Synthesis

    OpenAIRE

    Gouget, Guillaume; Debecker, Damien P.; Kim, Ara; Olivieri, Giorgia; Gallet, Jean-Jacques; Bournel, Fabrice; Thomas, Cyril; Ersen, Ovidiu; Moldovan, Simona; Sanchez, Clément; Carenco , Sophie; Portehault, David

    2017-01-01

    Metal borides have mostly been studied as bulk materials. The nanoscale provides new opportunities to investigate the properties of these materials, e.g., nanoscale hardening and surface reactivity. Metal borides are often considered stable solids because of their covalent character, but little is known on their behavior under a reactive atmosphere, especially reductive gases. We use molten salt synthesis at 750 °C to provide cobalt monoboride (CoB) nanocrystals embedded in an amorphous layer...

  6. Synthesis, Structure, and Properties of Refractory Hard-Metal Borides

    Science.gov (United States)

    Lech, Andrew Thomas

    As the limits of what can be achieved with conventional hard compounds, such as tungsten carbide, are nearing reach, super-hard materials are an area of increasing industrial interest. The refractory hard metal borides, such as ReB2 and WB4, offer an increasingly attractive alternative to diamond and cubic boron nitride as a next-generation tool material. In this Thesis, a thorough discussion is made of the progress achieved by our laboratory towards understanding the synthesis, structure, and properties of these extremely hard compounds. Particular emphasis is placed on structural manipulation, solid solution formation, and the unique crystallographic manifestations of what might also be called "super-hard metals".

  7. Metal Borohydrides synthesized from metal borides and metal hydrides

    DEFF Research Database (Denmark)

    Sommer, Sanna

    2014-01-01

    Aarhus C, Denmark email: gallafogh@hotmail.com / sanna-sommer@hotmail.com Magnesium boride, MgB2, ball milled with MH (M = Li, Na, Ca) followed by hydrogenation under high hydrogen pressure, readily forms the corresponding metal borohydrides, M(BH4)x (M = Li, Na, Ca) and MgH2 according to reaction scheme...... crystallization processes. In situ SR-PXD of the systems was the most promising, revealing the formation of β-Ca(BH4)2 similar to the the MgB2 – CaH2 system [5]. This connection stems from the similarities in the crystal structure of AlB2 and MgB2. MgB2 has also shown ability to form LiBH4 and NaBH4. However...

  8. Effect of boron paste thickness on the growth kinetics of Fe{sub 2}B boride layers during the boriding process

    Energy Technology Data Exchange (ETDEWEB)

    Campos, I. [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico)]. E-mail: ivan.campos@itesm.mx; Bautista, O. [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico); Ramirez, G. [IPN-SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico); Islas, M. [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico); Parra, J. de la [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico); Zuniga, L. [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico)

    2005-04-30

    Through this work we study the influence of the thickness of boron paste in the growth of Fe{sub 2}B boride layer during the paste boriding thermochemical treatment applied on AISI 1045 steel. Different thickness of boron paste over the material surface with constant temperature and time show the variability of the diffusion coefficient of boron in Fe{sub 2}B phase depending, basically, on the boron potential at the external surface of the substrate. The mobility of boron in the formed phase is determined by the balance mass equation that considers the concentration profiles in the corresponding interphases layer-substrate, the thermodynamic equilibrium in the growth of the iron boride layer and the experimental results obtained during the process.

  9. Two-level systems and negative thermal expansion of lutetium borides

    Science.gov (United States)

    Novikov, V. V.; Mitroshenkov, N. V.; Kornev, B. I.; Matovnikov, A. V.

    2017-05-01

    The heat capacity Cv(T) and unit cell volume V(T) temperature dependencies of lutetium borides LuB2 and LuB4 in the region of 2-300 K were analysed in the Debye-Einstein approximation. The characteristic temperatures of the Debye and Einstein components of boride heat capacity and thermal expansion were found. The anomalous contribution to the borides' thermal characteristics was revealed. This contribution was attributed to the influence of two-level systems (TLS), formed in the subsystem of lutetium ions due to asymmetry in the way they are surrounded by the boron atoms in the boride crystal structure. The TLS influence is revealed on heat capacity temperature dependencies by the Schottky-type maxima at Tmax LuB2 =13.8 K, Tmax LuB4 =22.7 K, as well as by the negative contribution to the borides' thermal expansion. The borides' Grüneisen parameters corresponding to the heat capacity and thermal expansion TLS anomalies are negative, and amount to several 10 s of units.

  10. Boron-Based Hydrogen Storage: Ternary Borides and Beyond

    Energy Technology Data Exchange (ETDEWEB)

    Vajo, John J. [HRL Laboratories, LLC, Malibu, CA (United States)

    2016-04-28

    DOE continues to seek reversible solid-state hydrogen materials with hydrogen densities of ≥11 wt% and ≥80 g/L that can deliver hydrogen and be recharged at moderate temperatures (≤100 °C) and pressures (≤100 bar) enabling incorporation into hydrogen storage systems suitable for transportation applications. Boron-based hydrogen storage materials have the potential to meet the density requirements given boron’s low atomic weight, high chemical valance, and versatile chemistry. However, the rates of hydrogen exchange in boron-based compounds are thus far much too slow for practical applications. Although contributing to the high hydrogen densities, the high valance of boron also leads to slow rates of hydrogen exchange due to extensive boron-boron atom rearrangements during hydrogen cycling. This rearrangement often leads to multiple solid phases occurring over hydrogen release and recharge cycles. These phases must nucleate and react with each other across solid-solid phase boundaries leading to energy barriers that slow the rates of hydrogen exchange. This project sought to overcome the slow rates of hydrogen exchange in boron-based hydrogen storage materials by minimizing the number of solid phases and the boron atom rearrangement over a hydrogen release and recharge cycle. Two novel approaches were explored: 1) developing matched pairs of ternary borides and mixed-metal borohydrides that could exchange hydrogen with only one hydrogenated phase (the mixed-metal borohydride) and only one dehydrogenated phase (the ternary boride); and 2) developing boranes that could release hydrogen by being lithiated using lithium hydride with no boron-boron atom rearrangement.

  11. In Situ Solid-Gas Reactivity of Nanoscaled Metal Borides from Molten Salt Synthesis.

    Science.gov (United States)

    Gouget, Guillaume; Debecker, Damien P; Kim, Ara; Olivieri, Giorgia; Gallet, Jean-Jacques; Bournel, Fabrice; Thomas, Cyril; Ersen, Ovidiu; Moldovan, Simona; Sanchez, Clément; Carenco, Sophie; Portehault, David

    2017-08-07

    Metal borides have mostly been studied as bulk materials. The nanoscale provides new opportunities to investigate the properties of these materials, e.g., nanoscale hardening and surface reactivity. Metal borides are often considered stable solids because of their covalent character, but little is known on their behavior under a reactive atmosphere, especially reductive gases. We use molten salt synthesis at 750 °C to provide cobalt monoboride (CoB) nanocrystals embedded in an amorphous layer of cobalt(II) and partially oxidized boron as a model platform to study morphological, chemical, and structural evolutions of the boride and the superficial layer exposed to argon, dihydrogen (H2), and a mixture of H2 and carbon dioxide (CO2) through a multiscale in situ approach: environmental transmission electron microscopy, synchrotron-based near-ambient-pressure X-ray photoelectron spectroscopy, and near-edge X-ray absorption spectroscopy. Although the material is stable under argon, H2 triggers at 400 °C decomposition of CoB, leading to cobalt(0) nanoparticles. We then show that H2 activates CoB for the catalysis of CO2 methanation. A similar decomposition process is also observed on NiB nanocrystals under oxidizing conditions at 300 °C. Our work highlights the instability under reactive atmospheres of nanocrystalline cobalt and nickel borides obtained from molten salt synthesis. Therefore, we question the general stability of metal borides with distinct compositions under such conditions. These results shed light on the actual species in metal boride catalysis and provide the framework for future applications of metal borides in their stability domains.

  12. Europium enabled luminescent nanoparticles for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Syamchand, S.S., E-mail: syamchand.ss@gmail.com; Sony, G., E-mail: emailtosony@gmail.com

    2015-09-15

    Lanthanide based nanoparticles are receiving great attention ought to their excellent luminescent and magnetic properties and find challenging biomedical applications. Among the luminescent lanthanide NPs, europium based NPs (Eu-NPs) are better candidates for immunoassay and imaging applications. The Eu-NPs have an edge over quantum dots (QDs) by means of their stable luminescence, long fluorescence lifetime, sharp emission peaks with narrow band width, lack of blinking and biocompatibility. This review surveys the synthesis and properties of a variety of Eu-NPs consolidated from different research articles, for their applications in medicine and biology. The exquisite luminescent properties of Eu-NPs are explored for developing biomedical applications such as immunoassay and bioimaging including multimodal imaging. The biomedical applications of Eu-NPs are mostly diagnostic in nature and mainly focus on various key analytes present in biological systems. The luminescent properties of europium enabled NPs are influenced by a number of factors such as the site symmetry, the metal nanoparticles, metal ions, quantum dots, surfactants, morphology of Eu-NPs, crystal defect, phenomena like antenna effect and physical parameters like temperature. Through this review we explore and assimilate all the factors which affect the luminescence in Eu-NPs and coil a new thread of parameters that control the luminescence in Eu-NPs, which would provide further insight in developing Eu-based nanoprobes for future biomedical prospects. - Highlights: • The review describes 14 major factors that influence the luminescence properties of europium enabled luminescent nanoparticles (Eu-NPs). • Surveys different types of europium containing nanoparticles that have been reported for their biomedical applications. • Eu-NPs are conveniently divided into four different categories, based on the type of the substrates involved. The four categories are (1) virgin Eu-substrate based NPs; (2

  13. The Europium Oxybarometer: Power and Pitfalls

    Science.gov (United States)

    McKay, G.

    2004-01-01

    One of the most important characteristics of a planet is the oxidation state of its mantle, as reflected in primitive basalts. Petrologists have devised several methods to estimate the oxygen fugacity under which basalts crystallized. One method that has been the subject of recent interest involves the depth of the Eu anomaly in first-crystallizing minerals. A discussion detailing the experimental calibration of the Europium oxybarometer and the application of this device to Angrites and Martian basaltic meteorites are presented. The strengths and weaknesses of the instrument are also included.

  14. Europium Effect on the Electron Transport in Graphene Ribbons

    Energy Technology Data Exchange (ETDEWEB)

    Bobadilla, Alfredo D.; Ocola, Leonidas E.; Sumant, Anirudha V.; Kaminski, Michael; Kumar, Narendra; Seminario, Jorge M.

    2015-10-01

    We report in this complementary theoretical-experimental work the effect of gating on the election transport of grapheme ribbons when exposed to very low concentration of europium in an aqueous solution. We find a direct correlation between the level of concentration of europium ions in the solvent and the change in electron transport in graphene, observing a change of up to 3 orders of magnitude at the lowest level of concentration tested (0.1 mM), suggesting a possibility that graphene ribbons can be used for detecting very low concentrations of europium in liquid solutions.

  15. New route toward nanosized crystalline metal borides with tuneable stoichiometry and variable morphologies.

    Science.gov (United States)

    Gouget, Guillaume; Beaunier, Patricia; Portehault, David; Sanchez, Clément

    2016-10-06

    Herein we highlight for the first time the ability to tune the stoichiometry of metal boride nanocrystals through nanoparticle synthesis in thermally stable inorganic molten salts. Two metal-boron systems are chosen as case studies: boron-poor nickel borides and boron-rich yttrium borides. We show that NiB, Ni4B3, Ni2B, Ni3B, and YB6 particles can be obtained as crystalline phases with good selectivity. Anisotropic crystallization is observed in two cases: the first boron-rich YB4 nanorods are reported, while boron-poor NiB nanoparticles show a peculiar crystal habit, as they are obtained as spheres with uniaxial defects related to the crystal structure. Crystallization mechanisms are proposed to account for the appearance of these two kinds of anisotropy at the nanoscale.

  16. Hardness optimization of boride diffusion layer on Astm F-75 alloy using response surface methodology

    Energy Technology Data Exchange (ETDEWEB)

    Arguelles O, J. L.; Corona R, M. A. [Universidad Autonoma de San Luis Potosi, Doctorado Institucional en Ingenieria y Ciencia de Materiales, San Luis Potosi 78000, SLP (Mexico); Marquez H, A.; Saldana R, A. L.; Saldana R, A. [Universidad de Guanajuato, Ingenieria Mecanica Agricola DICIVA, Irapuato, Guanajuato 36500 (Mexico); Moreno P, J., E-mail: amarquez@ugto.mx [Universidad de Guanajuato, Departamento de Minas, Metalurgia y Geologia, Ex-Hacienda San Matias s/n, Guanajuato, Guanajuato 36020 (Mexico)

    2017-11-01

    In this study, the Response Surface Methodology (Rsm) and Central Composite Design (Ccd) were used to optimize the hardness of boride diffusion layer on Astm F-75 alloy (also called Haynes alloy). A boronizing thermochemical treatment was carried out at different temperatures and for different time periods. Hardness tests were conducted. The boride diffusion layer was verified by the X-ray diffraction (XRD) analysis indicating the formation of Co B, Co{sub 2}B, Cr B and Mo{sub 2}B phases. An optimal hardness of 3139.7 Hv was obtained for the samples subjected to the boriding process for a duration of 6.86 h at 802.4 degrees Celsius. (Author)

  17. Metal-boride phase formation on tungsten carbide (WC-Co) during microwave plasma chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, Jamin M.; Catledge, Shane A., E-mail: catledge@uab.edu

    2016-02-28

    Graphical abstract: - Highlights: • A detailed phase analysis after PECVD boriding shows WCoB, CoB and/or W{sub 2}CoB{sub 2}. • EDS of PECVD borides shows boron diffusion into the carbide grain structure. • Nanoindentation hardness and modulus of borides is 23–27 GPa and 600–780 GPa. • Scratch testing shows hard coating with cracking at 40N and spallation at 70N. - Abstract: Strengthening of cemented tungsten carbide by boriding is used to improve the wear resistance and lifetime of carbide tools; however, many conventional boriding techniques render the bulk carbide too brittle for extreme conditions, such as hard rock drilling. This research explored the variation in metal-boride phase formation during the microwave plasma enhanced chemical vapor deposition process at surface temperatures from 700 to 1100 °C. We showed several well-adhered metal-boride surface layers consisting of WCoB, CoB and/or W{sub 2}CoB{sub 2} with average hardness from 23 to 27 GPa and average elastic modulus of 600–730 GPa. The metal-boride interlayer was shown to be an effective diffusion barrier against elemental cobalt; migration of elemental cobalt to the surface of the interlayer was significantly reduced. A combination of glancing angle X-ray diffraction, electron dispersive spectroscopy, nanoindentation and scratch testing was used to evaluate the surface composition and material properties. An evaluation of the material properties shows that plasma enhanced chemical vapor deposited borides formed at substrate temperatures of 800 °C, 850 °C, 900 °C and 1000 °C strengthen the material by increasing the hardness and elastic modulus of cemented tungsten carbide. Additionally, these boride surface layers may offer potential for adhesion of ultra-hard carbon coatings.

  18. Paramagnetic Europium Salen Complex and Sickle-Cell Anemia

    Science.gov (United States)

    Wynter, Clive I.; Ryan, D. H.; May, Leopold; Oliver, F. W.; Brown, Eugene; Hoffman, Eugene J.; Bernstein, David

    2005-04-01

    A new europium salen complex, Eu(salen)2NH4, was synthesized, and its composition was confirmed by chemical analysis and infrared spectroscopy. Further characterization was carried out by 151 Eu Mössbauer spectroscopy and magnetic susceptibility measurements. Mössbauer spectroscopic measurements were made at varying temperatures between 9 K and room temperature and a value of Debye temperature of 133 ±5 K was computed. Both Mössbauer and magnetic susceptibility measurements confirmed the paramagnetic behavior of this complex and the trivalent state of the europium ion. In view of the fact that the "odd" paramagnetic molecule NO has been shown to reverse sickling of red blood cells in sickle cell anemia, the interaction between the paramagnetic europium salen complex and sickle cells was examined after incubation with this europium complex and shown to have similar effects.

  19. Europium polyoxometalates encapsulated in silica nanoparticles - characterization and photoluminescence studies

    Energy Technology Data Exchange (ETDEWEB)

    Neves, Cristina S.; Granadeiro, Carlos M.; Cunha-Silva, Luis; Eaton, Peter; Balula, Salete S.; Pereira, Eulalia [REQUIMTE/Departamento de Quimica e Bioquimica, Faculdade de Ciencias, Universidade do Porto (Portugal); Ananias, Duarte [CICECO, Departamento de Quimica, Universidade de Aveiro (Portugal); Gago, Sandra [REQUIMTE, Departamento de Quimica, Faculdade de Ciencias e Tecnologia, Universidade Nova de Lisboa, Monte de Caparica (Portugal); Feio, Gabriel [CENIMAT/I3N, Departamento de Ciencia dos Materiais, Faculdade de Ciencias e Tecnologia, Universidade Nova de Lisboa, Monte de Caparica (Portugal); Carvalho, Patricia A. [ICEMS/Departamento de Bioengenharia, Instituto Superior Tecnico, Lisboa (Portugal)

    2013-06-15

    The incorporation of europium polyoxometalates into silica nanoparticles can lead to a biocompatible nanomaterial with luminescent properties suitable for applications in biosensors, biological probes, and imaging. Keggin-type europium polyoxometalates Eu(PW{sub 11}){sub x} (x = 1 and 2) with different europium coordination environments were prepared by using simple methodologies and no expensive reactants. These luminescent compounds were then encapsulated into silica nanoparticles for the first time through the water-in-oil microemulsion methodology with a nonionic surfactant. The europium polyoxometalates and the nanoparticles were characterized by using several techniques [FTIR, FT-Raman, {sup 31}P magic angle spinning (MAS) NMR, and TEM/energy-dispersive X-ray spectroscopy (TEM-EDS), AFM, dynamic light scattering (DLS), and inductively coupled plasma MS (ICP-MS) analysis]. The stability of the material and the integrity of the europium compounds incorporated were also examined. Furthermore, the photoluminescence properties of the Eu(PW{sub 11}){sub x} rate at SiO{sub 2} nanomaterials were evaluated and compared with those of the free europium polyoxometalates. The silica surface of the most stable nanoparticles was successfully functionalized with appropriate organosilanes to enable the covalent binding of oligonucleotides. (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. Spectral Properties of a bis-Azospiropyran Complexed with Europium

    Science.gov (United States)

    Nourmohammadian, F.; Ghahari, M.; Gholami, M. Davoudzadeh

    2015-09-01

    The complexation of recently synthesized symmetrical bifunctional bis-azospiropyran photochromic dye with europium nitrate and its effect on UV-vis absorption and fluorescent emission was studied. Upon addition of Eu 3+ to colorless spiropyran, a yellow merocyanine europium complex was obtained with an absorption band at 410 nm. Negatively charged phenolic oxygenin zwitterionic ring-open form provides an effective metal binding site for Eu 3+ . Meanwhile, the inherent fluorescence emission of the photochromic dye at 380 nm is switched off due to the Eu 3+ - induced drive of spiro-mero equilibrium to form mero form. The stoichiometry of dye-europium complexation was evaluated by fluorescence emission and UV-vis absorption spectroscopy and a 8:1 ratio was obtained in both cases. The binding constant (K) value of the dye-europium complex was 3 × 106 M -1 . In conclusion, the current molecular switch is a useful sensitive dual measuring tool for solutions containing europium or europium-like elements by evaluation of visible absorption or fluorescent emission spectroscopy.

  1. Metal plasmon enhanced europium complex luminescence

    Energy Technology Data Exchange (ETDEWEB)

    Liu Feng [Department of Chemistry, Queen' s University, 90 Bader Lane, Kingston, Ontario, K7L 3N6 (Canada); Aldea, Gabriela [Department of Chemistry, Queen' s University, 90 Bader Lane, Kingston, Ontario, K7L 3N6 (Canada); Petru Poni Institute of Macromolecular Chemistry Iasi, Aleea Grigore Ghica Voda 41A, 700487 Iasi (Romania); Nunzi, Jean-Michel, E-mail: nunzijm@queensu.c [Department of Chemistry, Queen' s University, 90 Bader Lane, Kingston, Ontario, K7L 3N6 (Canada)

    2010-01-15

    The plasmon enhanced luminescence of a rare-earth complex Tris(6, 6, 7, 7, 8, 8, 8-heptafluoro-2, 2-dimethyl-3, 5-octanedionato) europium (Eu(fod){sub 3}) was investigated. A polyvinyl alcohol (PVA) thin film was successfully adopted as a spacer to separate the Eu complex from the silver island film (SIF), and five-fold enhancement of the radiative decay rate of the Eu complex on SIF was demonstrated based on the luminescence intensity and lifetime measurement. Investigation of the distance dependent luminescence indicates that 7 nm is an optimal distance for SIF enhanced Eu luminescence. Plasmon enhanced rare-earth luminescence based on an organic film spacer would find potential applications in plasmon enhanced organic light emitting diode (OLED) devices.

  2. Surface hardening of St41 low carbon steel by using the hot-pressing powder-pack boriding method

    Science.gov (United States)

    Sutrisno, Soegijono, Bambang

    2014-03-01

    This research describes a powder-pack boriding process by using hot-pressing technic for St41 low carbon steel which will improve the hardness on the substrate by forming boride layer solid solution. Those method can reduce the operational cost of the research if it is compared by the conventional method with the asmospheric condition both vacuum system and gas inert condition. The concept of boriding by hot-pressing technic was verified in a laboratory scale. Welldefined and reusedable technic was achieved by using the stainless steel 304 as the container and sealed with a 5 ton pressure. This container was filled boronizing powder consisting of 5%B4C, 90%SiC, and 5%KBF4 to close the St41 low carbon steel specimen inside the container. The St41 boriding specimen was treated at the temperature of 900°C for 8 hours. The boride layer on the substrate was found as FeB and Fe2B phase with the hardness about 1800 HV. This value was more than ten times if compared with the untreated specimen that only had the hardness of 123 HV. Depend on heat treatment temperature, heat treatment time, and powder-pack boriding pressure, the depth of boride layer range from 127 to 165 μm, leading to a diffusion controlled process.

  3. Novel fluorescent probe for low density lipoprotein, based on the enhancement of Europium emission band

    OpenAIRE

    Courrol, Lilia Coronato; Monteiro, A.M.; SILVA, F.R.O.; L. Gomes; VIEIRA, N.D.; Gidlund, Magnus; Figueiredo Neto, A.M.

    2007-01-01

    We report here the observation of the enhancement of Europium-tetracycline complex emission in Low Density Lipoprotein (LDL) solutions. Europium emission band of tetracycline solution containing Europium (III) chloride hexahydrate was tested to obtain effective enhancement in the presence of native LDL and oxidized LDL. Europium emission lifetime in the presence of lipoproteins was measured, resulting in a simple method to measure the lipoproteins quantity in an aqueous solution at physiologi...

  4. Growth kinetics of boride layers formed on 99.0% purity nickel

    Indian Academy of Sciences (India)

    1Department of Metallurgical and Materials Engineering, Faculty of Technology, Afyon Kocatepe University,. 03200 Afyonkarahisar, Turkey. 2Laboratory of Materials Technology, Faculty of Mechanical Engineering and Process Engineering, USTHB, B.P. No. 32, ... in a negative effect on the boride layer in terms of both.

  5. Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

    Science.gov (United States)

    Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

    2017-11-01

    The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

  6. Ultra-Fast Boriding in High-Temperature Materials Processing Industries

    Energy Technology Data Exchange (ETDEWEB)

    None

    2008-12-01

    This factsheet describes a research project whose main objective is to further develop, optimize, scale-up, and commercialize an ultra-fast boriding (also referred to as “boronizing”) process that can provide much higher energy efficiency, productivity, and near-zero emissions in many of the high-temperature materials processing industries.

  7. Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

    Science.gov (United States)

    Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

    2017-10-01

    The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

  8. Europium ion as a probe for binding sites to carrageenans

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, Ana P.; Goncalves, Rogeria R.; Serra, Osvaldo A. [Departamento de Quimica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, Ribeirao Preto, Sao Paulo 14040-901 (Brazil); Zaniquelli, Maria Elisabete D. [Departamento de Quimica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, Ribeirao Preto, Sao Paulo 14040-901 (Brazil)], E-mail: medzaniquelli@ffclrp.usp.br; Wong, Kenneth [Laboratorio de Fisico-Quimica, Centro de Pesquisas de Paulinia, Rhodia Brasil, Paulinia, Sao Paulo (Brazil)

    2007-12-15

    Carrageenans, sulfated polysaccharides extracted from red algae, present a coil-helix transition and helix aggregation dependence on the type and concentration of counterions. In this study, we focus attention on a mixed valence counterion system: Eu{sup 3+}/Na{sup +} or K{sup +} with different gel-forming carrageenans: kappa, iota, and kappa-2. Results of stationary and time-dependent luminescence showed to be a suitable tool to probe ion binding to both the negatively charged sulfate group and the hydroxyl groups present in the biopolymer. For lower europium ion concentrations, a single longer decay emission lifetime was detected, which was attributed to the binding of europium ion to the carrageenan sulfate groups. An additional decay ascribed to europium binding to hydroxyl groups was observed above a threshold concentration, and this decay was dependent on the carrageenan charge density. Symmetry of the europium ion microenvironment was estimated by the ratio between the intensities of its emission bands, which has been shown to depend on the concentration of europium ions and on the specificity of the monovalent counterion bound to the carrageenan.

  9. Signs of superconductivity at 110 K on inclusions of TiB sub k boride phases into titanium matrix

    CERN Document Server

    Volkov, V V; Berzverkhij, P P; Martynets, V G; Matizen, E V

    2002-01-01

    Verification of theoretical forecasts on the possibility of the high-temperature superconductivity of the high-temperature superconductivity (HTSC) in the TiB sub k titanium borides is accomplished. It is established that the jump-like change in the temperature dependence of the electric resistance R(T) at 110 K takes place on the titanium samples, the surfaces whereof are coated with the borides diffusion layers of the TiB sub k variable in-depth composition. This proves the presence of the borides diffusion layers are applied onto the metallic titanium by means of treating its surface with the B sub 2 H sub 6 + H sub 2 gases mixture at the temperature of 610-700 deg C with the subsequent annealing in vacuum. The boride layers composition is studied through the mass-spectrometry method

  10. First-Principles Investigations on Europium Monoxide

    KAUST Repository

    Wang, Hao

    2011-05-01

    Europium monoxide is both an insulator and a Heisenberg ferromagnet (Tc=69 K). In the present thesis, the author has investigated the electronic structure of different types of EuO by density functional theory. The on-site Coulomb interaction of the localized Eu 4f and 5d electrons, which is wrongly treated in the standard generalized gradient approximation method, is found to be crucial to obtain the correct insulating ground state as observed in experiments. Our results show that the ferromagnetism is stable under pressure, both hydrostatic and uniaxial. For both types of pressure an insulator-metal transition is demonstrated. Moreover, the experimentally observed insulator-metal transition in oxygen deficient and gadolinium-doped EuO is reproduced in our calculations for impurity concentrations of 6.25% and 25%. Furthermore, a 10- layer EuO thin film is theoretically predicted to be an insulator with a narrow band gap of around 0.08 eV, while the Si/EuO interface shows metallic properties with the Si and O 2p as well as Eu 5d bands crossing the Fermi level.

  11. Chloride, bromide and iodide scintillators with europium

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2016-09-27

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  12. Electrochemical extraction of europium from molten fluoride media

    Energy Technology Data Exchange (ETDEWEB)

    Gibilaro, M. [Universite de Toulouse, INPT, UPS, Laboratoire de Genie Chimique, Departement Procedes Electrochimiques, F-31062 Toulouse cedex 09 (France); CNRS, Laboratoire de Genie Chimique, F-31062 Toulouse cedex 09 (France); Massot, L., E-mail: massot@chimie.ups-tlse.f [Universite de Toulouse, INPT, UPS, Laboratoire de Genie Chimique, Departement Procedes Electrochimiques, F-31062 Toulouse cedex 09 (France); CNRS, Laboratoire de Genie Chimique, F-31062 Toulouse cedex 09 (France); Chamelot, P.; Cassayre, L.; Taxil, P. [Universite de Toulouse, INPT, UPS, Laboratoire de Genie Chimique, Departement Procedes Electrochimiques, F-31062 Toulouse cedex 09 (France); CNRS, Laboratoire de Genie Chimique, F-31062 Toulouse cedex 09 (France)

    2009-12-15

    This work concerns the extraction of europium from molten fluoride media. Two electrochemical ways have been examined: (i) the use of a reactive cathode made of copper and (ii) the co-deposition with aluminium on inert electrode, leading to the formation of europium-copper and europium-aluminium alloys, respectively, as identified by SEM-EDS analysis. Cyclic voltammetry and square wave voltammetry were used to identify the reduction pathway and to characterise the step of Cu-Eu and Al-Eu alloys formation. Then, electrochemical extractions using the two methodologies have been performed with extraction efficiency around 92% for copper electrode and 99.7% for co-reduction with aluminium ions.

  13. Solubilization of europium fulvate in aqueous solutions containing complexing agents

    Energy Technology Data Exchange (ETDEWEB)

    Legin, E.K.; Trifonov, Yu.I.; Khokhlov, M.L. [Khlopin Radium Inst., St. Petersburg (Russian Federation)] [and others

    1995-07-01

    The europium fulvate complex is synthesized and characterized by spectroscopic and chemical methods. By an example of this complex, it is demonstrated that metal complexes of humic substances are solubilized in the presence of complexing anions such as OAc{sup {minus}}, C{sub 2}O{sup 2{minus}}{sub 4}, and EDTA{sup 2{minus}}. The solubilization is studied by the optical and radioactive tracer methods. The solubilization of europium fulvate increases parallel to the complexing power of anions. In the solid fulvate europium is bonded stronger than in the ethylenediaminetetraacetate complex. The solubilization is considered as a potential source for decomposition of the {open_quotes}absorbing soil complex,{close_quotes} resulting in mobile forms of a metal and humic component in soils and soil waters.

  14. Excess europium content in Precambrian sedimentary rocks and continental evolution

    Science.gov (United States)

    Jakes, P.; Taylor, S. R.

    1974-01-01

    It is proposed that the europium excess in Precambrian sedimentary rocks, relative to those of younger age, is derived from volcanic rocks of ancient island arcs, which were the source materials for the sediments. Precambrian sedimentary rocks and present-day volcanic rocks of island arcs have similar REE patterns, total REE abundances, and excess Eu, relative to the North American shale composite. The present upper crustal REE pattern, as exemplified by that of sediments, is depleted in Eu, relative to chondrites. This depletion is considered to be a consequence of development of a granodioritic upper crust by partial melting in the lower crust, which selectively retains europium.

  15. The Relationship of the Chemical Bonding Topology of High Critical Temperature Copper Oxide Superconductors to that of the Chevrel Phases and the Ternary Lanthanide Rhodium Borides.

    Science.gov (United States)

    1987-12-11

    to those of the ternary molybdenum chalcogenides and ternary lanthanide rhodium borides in which the conducting skeleton is constructed from metal...Bonding Topology of High Critical Temperature Copper Oxide Superconductors to That of The Chevrel Phases and the Ternary Lanthanide Rhodium Borides by R...REPORT NUMBER P Rhodium Borides 7 AUTHOR(s ) S. CONTRACT OR GRANT NUMIER(*) f, % .0, R.B. King N00014-84-K-0365 S. PERFORMING ORGANIZATION NAME AND

  16. Friction and wear of radiofrequency-sputtered borides, silicides, and carbides

    Science.gov (United States)

    Brainard, W. A.; Wheeler, D. R.

    1978-01-01

    The friction and wear properties of several refractory compound coatings were examined. These compounds were applied to 440 C bearing steel surfaces by radiofrequency (RF) sputtering. The refractory compounds were the titanium and molybdenum borides, the titanium and molybdenum silicides, and the titanium, molybdenum, and boron carbides. Friction testing was done with a pin-on-disk wear apparatus at loads from 0.1 to 5.0 newtons. Generally, the best wear properties were obtained when the coatings were bias sputtered onto 440 C disks that had been preoxidized. Adherence was improved because of the better bonding of the coatings to the iron oxide formed during preoxidation. As a class the carbides provided wear protection to the highest loads. Titanium boride coatings provided low friction and good wear properties to moderate loads.

  17. Electrosynthesis of tantalum borides in oxygen-free and oxygen-containing fluoride melts

    DEFF Research Database (Denmark)

    Polyakova, L.P.; Polyakov, E.G.; Makarova, O.V.

    2001-01-01

    Results of electrosynthesis of tantalum borides in fluoride and oxyfluoride melts are compared. It is shown that the single-phase X-ray-amorphous micro-layered coatings form only in the latter case. Linear and square-wave voltammetry, complemented by X-ray diffraction analysis, IR spectroscopy......, and OC, reveals that the reason for their formation is the cathodic reduction of heteronuclear tantalum and boron complexes....

  18. Preparation of molybdenum borides by combustion synthesis involving solid-phase displacement reactions

    Energy Technology Data Exchange (ETDEWEB)

    Yeh, C.L. [Department of Mechanical and Automation Engineering, Da-Yeh University, 112 Shan-Jiau Rd., Da-Tsuen, Changhua 51505, Taiwan (China)], E-mail: clyeh@mail.dyu.edu.tw; Hsu, W.S. [Department of Mechanical and Automation Engineering, Da-Yeh University, 112 Shan-Jiau Rd., Da-Tsuen, Changhua 51505, Taiwan (China)

    2008-06-12

    Preparation of molybdenum borides of five different phases in the Mo-B binary system (including Mo{sub 2}B, MoB, MoB{sub 2}, Mo{sub 2}B{sub 5}, and MoB{sub 4}) was performed by self-propagating high-temperature synthesis (SHS) with two kinds of the reactant samples. When elemental powder compacts with an exact stoichiometry corresponding to the boride phase were employed, self-sustaining reaction was only achieved in the sample with Mo:B = 1:1 and nearly single-phase MoB was yielded. Therefore, the other four boride compounds were prepared from the reactant compacts composed of MoO{sub 3}, Mo, and B powders, within which the displacement reaction of MoO{sub 3} with boron was involved in combustion synthesis. Experimental evidence shows that the extent of displacement reaction in the overall reaction has a significant impact on sustainability of the synthesis reaction, combustion temperature, reaction front velocity, and composition of the end product. An increase in the solid-phase displacement reaction taking place during the SHS process contributes more heat flux to the synthesis reaction, thus resulting in the increase of combustion temperature and enhancement of the reaction front velocity. Based upon the XRD analysis, formation of Mo{sub 2}B, MoB{sub 2}, and Mo{sub 2}B{sub 5} as the dominant boride phase in the end product was successful through the SHS reaction with powder compacts under appropriate stoichiometries between MoO{sub 3}, Mo, and B. However, a poor conversion was observed in the synthesis of MoB{sub 4}. The powder compact prepared for the production of MoB{sub 4} yielded mostly Mo{sub 2}B{sub 5}.

  19. Influence of Re Concentration on the Mechanical Properties of Tungsten Borides from First-Principles Calculations

    Science.gov (United States)

    Pan, Yong; Lin, Yuanhua

    2017-10-01

    Tungsten borides are promising high-temperature materials. However, the structure and hardening mechanisms of tungsten boride are still great challenges. To solve the problems, we apply the first-principles method to study the structure of WB3 and explore the influence of alloying element Re on the mechanical properties of WB3. The calculated Vickers hardness of WB3 is 39.1 GPa. We further find that a low concentration of Re can improve the hardness of WB3, which is in good agreement with the experimental result. However, the hardness and elastic properties of WB3 decrease gradually with increasing Re concentration. The calculated results show that the structure and hardness of WB3 are attributed to the B-B hexagonal prism. A high concentration of Re weakens the charge interaction between the B-B atoms, and reduces the mechanical properties of WB3. Therefore, we can adjust the alloy concentration to improve the Vickers hardness of transition metal borides.

  20. Structure of superhard tungsten tetraboride: A missing link between MB2 and MB12 higher borides

    Science.gov (United States)

    Lech, Andrew T.; Turner, Christopher L.; Mohammadi, Reza; Tolbert, Sarah H.; Kaner, Richard B.

    2015-01-01

    Superhard metals are of interest as possible replacements with enhanced properties over the metal carbides commonly used in cutting, drilling, and wear-resistant tooling. Of the superhard metals, the highest boride of tungsten—often referred to as WB4 and sometimes as W1–xB3—is one of the most promising candidates. The structure of this boride, however, has never been fully resolved, despite the fact that it was discovered in 1961—a fact that severely limits our understanding of its structure–property relationships and has generated increasing controversy in the literature. Here, we present a new crystallographic model of this compound based on refinement against time-of-flight neutron diffraction data. Contrary to previous X-ray–only structural refinements, there is strong evidence for the presence of interstitial arrangements of boron atoms and polyhedral bonding. The formation of these polyhedra—slightly distorted boron cuboctahedra—appears to be dependent upon the defective nature of the tungsten-deficient metal sublattice. This previously unidentified structure type has an intermediary relationship between MB2 and MB12 type boride polymorphs. Manipulation of the fractionally occupied metal and boron sites may provide insight for the rational design of new superhard metals. PMID:25733870

  1. Structure of superhard tungsten tetraboride: a missing link between MB2 and MB12 higher borides.

    Science.gov (United States)

    Lech, Andrew T; Turner, Christopher L; Mohammadi, Reza; Tolbert, Sarah H; Kaner, Richard B

    2015-03-17

    Superhard metals are of interest as possible replacements with enhanced properties over the metal carbides commonly used in cutting, drilling, and wear-resistant tooling. Of the superhard metals, the highest boride of tungsten--often referred to as WB4 and sometimes as W(1-x)B3--is one of the most promising candidates. The structure of this boride, however, has never been fully resolved, despite the fact that it was discovered in 1961--a fact that severely limits our understanding of its structure-property relationships and has generated increasing controversy in the literature. Here, we present a new crystallographic model of this compound based on refinement against time-of-flight neutron diffraction data. Contrary to previous X-ray-only structural refinements, there is strong evidence for the presence of interstitial arrangements of boron atoms and polyhedral bonding. The formation of these polyhedral--slightly distorted boron cuboctahedra--appears to be dependent upon the defective nature of the tungsten-deficient metal sublattice. This previously unidentified structure type has an intermediary relationship between MB2 and MB12 type boride polymorphs. Manipulation of the fractionally occupied metal and boron sites may provide insight for the rational design of new superhard metals.

  2. Murine High Specificity/Sensitivity Competitive Europium Insulin Autoantibody Assay

    Science.gov (United States)

    Babaya, Naru; Liu, Edwin; Miao, DongMei; Li, Marcella; Yu, Liping

    2009-01-01

    Abstract Background Most insulin autoantibody assays for both human and animal models are in a radioassay format utilizing 125I-insulin, but despite the radioassay format international workshops have documented difficulty in standardization between laboratories. There is thus a need for simpler assay formats that do not utilize radioactivity, yet retain the high specificity and sensitivity of radioassays. Methods To establish an easier enzyme-linked immunosorbent assay (ELISA) for insulin autoantibodies of non-obese diabetic (NOD) mice, we used an ELISA format, competition with unlabeled insulin, europium-avidin, and time-resolved fluorescence detection (competitive europium insulin autoantibody assay). Results The competitive europium assay of insulin autoantibodies when applied to sera from NOD mice had high sensitivity and specificity (92% sensitivity, 100% specificity) compared to our standard insulin autoantibody radioassay (72% sensitivity, 100% specificity) in analyzing blind workshop sera. It is noteworthy that though the assay has extremely high sensitivity for murine insulin autoantibodies and utilizes human insulin as target autoantigen, human sera with high levels of insulin autoantibodies are not detected. Conclusions Our results clearly indicate that low levels of insulin autoantibodies can be detected in an ELISA-like format. Combining a europium-based ELISA with competition with fluid-phase autoantigen can be applicable to many autoantigens to achieve high specificity and sensitivity in an ELISA format. PMID:19344197

  3. Tridentate benzimidazole-pyridine-tetrazolates as sensitizers of europium luminescence.

    Science.gov (United States)

    Shavaleev, Nail M; Eliseeva, Svetlana V; Scopelliti, Rosario; Bünzli, Jean-Claude G

    2014-05-19

    We report on new anionic tridentate benzimidazole-pyridine-tetrazolate ligands that form neutral 3:1 complexes with trivalent lanthanides. The ligands are UV-absorbing chromophores that sensitize the red luminescence of europium with energy-transfer efficiency of 74-100%. The lifetime and quantum yield of the sensitized europium luminescence increase from 0.5 ms and 12-13% for the as-prepared solids to 2.8 ms and 41% for dichloromethane solution. From analysis of the data, the as-prepared solids can be described as aqua-complexes [Ln(κ(3)-ligand)2(κ(1)-ligand)(H2O)x] where the coordinated water molecules are responsible for the strong quenching of the europium luminescence. In solution, the coordinated water molecules are replaced by the nitrogen atoms of the κ(1)-ligand to give anhydrous complexes [Ln(κ(3)-ligand)3] that exhibit efficient europium luminescence. X-ray structures of the anhydrous complexes confirm that the lanthanide ion (La(III), Eu(III)) is nine-coordinate in a distorted tricapped trigonal prismatic environment and that coordination of the lanthanide ion by tetrazolate is weaker than by carboxylate.

  4. Europium 2-benzofuranoate: Synthesis and use for bioimaging

    Science.gov (United States)

    Utochnikova, V. V.; Koshelev, D. S.; Medvedko, A. V.; Kalyakina, A. S.; Bushmarinov, I. S.; Grishko, A. Yu; Schepers, U.; Bräse, S.; Vatsadze, S. Z.

    2017-12-01

    Europium 2-benzofuranoate Eu(BFC)3(H2O)3 was successfully used for bioimaging in cellulo due to the combination of high solubility and high luminescence intensity in solution. It was possible due to the purposeful variation of the aromatic core of carboxylate anion.

  5. SEPARATION OF EUROPIUM FROM OTHER LANTHANIDE RAE EARTHS BY SOLVENT EXTRACTION

    Science.gov (United States)

    Peppard, D.F.; Horwitz, E.P.; Mason, G.W.

    1963-02-12

    This patent deals with a process of separating europium from other lanthanides present in aqueous hydrochloric or sulfuric acid solutions. The europium is selectively reduced to the divalent state with a divalent chromium salt formed in situ from chromium(III) salt plus zinc amalgam. The other trivalent lanthanides are then extracted away from the divalent europium with a nitrogen-flushed phosphoric acid ester or a phosphonic acid ester. (AEC)

  6. Distribution, elimination, and renal effects of single oral doses of europium in rats.

    Science.gov (United States)

    Ohnishi, Keiko; Usuda, Kan; Nakayama, Shin; Sugiura, Yumiko; Kitamura, Yasuhiro; Kurita, Akihiro; Tsuda, Yuko; Kimura, Motoshi; Kono, Koichi

    2011-11-01

    Single doses of europium (III) chloride hexahydrate were orally administered to several groups of rats. Cumulative urine samples were taken at 0-24 h, and blood samples were drawn after 24-h administration. The europium concentration was determined in these samples by inductively coupled plasma atomic emission spectroscopy. The volume, creatinine, ß-2-microglobulin, and N-acetyl-ß-D-glucosaminidase were measured in the urine samples to evaluate possible europium-induced renal effects. The blood samples showed low europium distribution, with an average of 77.5 μg/L for all groups. Although the urinary concentration and excretion showed dose-dependent increases, the percentage of europium excreted showed a dose-dependent decrease, with an average of 0.31% in all groups. The administration of europium resulted in a significant decrease of creatinine and a significant increase of urinary volume, N-acetyl-ß-D-glucosaminidase, and ß-2-microglobulin. Rare earth elements, including europium, are believed to form colloidal conjugates that deposit in the reticuloendothelial system and glomeruli. This specific reaction may contribute to low europium bioavailability and renal function disturbances. Despite low bioavailability, the high performance of the analytical method for determination of europium makes the blood and urine sampling suitable tools for monitoring of exposure to this element. The results presented in this study will be of great importance in future studies on the health impacts of rare earth elements.

  7. Effect of High Configuration Entropy and Rare Earth Addition on Boride Precipitation and Mechanical Properties of Multi-principal-Element Alloys

    Science.gov (United States)

    Zhang, H.; Zhong, X. C.; He, Y. Z.; Li, W. H.; Wu, W. F.; Chen, G.; Guo, S.

    2017-08-01

    A series of multi-principal-element (MPE) alloys have been prepared by adding Ni, Mn, Al, Cu and Y into the reference CoCrFe-B alloy. The microstructure and mechanical properties of these MPE alloys have been investigated thoroughly. It is found that the addition of the elements can inhibit boride precipitation in the designed alloys and the solid solution strengthening effect induced by interstitial boron atoms is more significant than that by boride precipitation. The MPE alloys with the fcc phase as the main solid solution phase have a higher boron solubility and hence less boride precipitation, than those with the bcc phase as the main solid solution phase. The addition of yttrium can improve the boron solubility, decrease boride precipitation, control the boride morphology and, importantly, simultaneously improve the compressive strength and ductility of boron-containing MPE alloys.

  8. The Hardness of Boride Layer on the S45C Iron (A preliminary study on surface hardening of ferrous material

    Directory of Open Access Journals (Sweden)

    Sutrisno

    2012-08-01

    Full Text Available The property such as microhardness of boride layer formed on S45C iron was investigated. Boronizing was carried out in a solid medium consisting of nano size powders of 50% B4C as a donor, 45% SiC as a diluent, and 5% KBF4 as an activator treated at the temperature of 10000C for 8 hours. The phases that were formed on the substrate was found as Fe2B and FeB layer that had smooth and flate shape morphology. The hardness of boride layer on S45C was over 2000 HV, while the hardness of untreated S45C iron was about 196,39 HV. Depending on process time and temperature, the depth of boride layer ranges from 25 to 55 µm, leading to a diffusion controlled process

  9. [Synthesis and luminescence properties of reactive ternary europium complexes].

    Science.gov (United States)

    Guo, Dong-cai; Shu, Wan-gen; Zhang, Wei; Liu, You-nian; Zhou, Yue

    2004-09-01

    In this paper, five new reactive ternary europium complexes were synthesized with the first ligand of 1,10-phenanthroline and the reactive second ligands of maleic anhydride, acrylonitrile, undecenoic acid, oleic acid and linoleic acid, and also characterized by means of elemental analysis, EDTA titrimetric method, FTIR spectra and UV spectra. The fluorescence spectra show that the five new ternary complexes have much higher luminescence intensity than their corresponding binary complexes, and the synergy ability sequence of the five reactive ligands is as follows: linoleic acid > oleic acid > acrylonitrile > maleic anhydride > undecenoic acid. At the same time, the reactive ternary europium complexes coordinated with the reactive ligands, which can be copolymerized with other monomers, will provide a new way for the synthesis of bonding-type rare earth polymer functional materials with excellent luminescence properties.

  10. Solvent extraction of europium(III) to a fluorine-free ionic liquid phase with a diglycolamic acid extractant

    OpenAIRE

    Rout, Alok; Souza, Ernesto Rezende; Binnemans, Koen

    2014-01-01

    Europium(III) was extracted by bis(2-ethylhexyl)diglycolamic acid (DEHDGA) dissolved in the non-fluorinated ionic liquid tetraoctylammonium dodecyl sulphate, [N8888][DS]. The extraction behaviour of europium(III) was investigated as a function of various parameters: pH, extractant concentration, concentration of the europium(III) ion in the aqueous feed and concentration of the salting-out agent. A comparison was made with extraction of europium(III) by the acidic extractants bis(2-ethylhexyl...

  11. Silver lead borate glasses doped with europium ions for phosphors ...

    Indian Academy of Sciences (India)

    2017-07-25

    Jul 25, 2017 ... Abstract. Europium (Eu3+) doped silver lead borate glasses with the composition of xEu2O3−(1 − x)Ag2. O−29PbO−70B2O3 (x = 0, 0.1, 0.2, 0.3, 0.4 and 0.5 mol%) have been successfully prepared by conventional melt quenching method. Thermal, structural and luminescence properties have been studied ...

  12. Silver lead borate glasses doped with europium ions for phosphors ...

    Indian Academy of Sciences (India)

    Europium (Eu 3 + ) doped silver lead borate glasses with the composition of x Eu 2 O 3 −( 1 − x )Ag 2 O−29PbO−70B 2 O 3 ( x = 0 , 0.1, 0.2, 0.3, 0.4 and 0.5 mol%) have been successfully prepared by conventional meltquenching method. Thermal, structural and luminescence properties have been studied using ...

  13. Synthesis and luminescence properties for europium oxide nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Mo Zunli, E-mail: mozl@163.com [Key Laboratory of Eco-Environment-Related Polymer Materials, Ministry of Education of China, Key Laboratory of Polymer Materials of Gansu Province, College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou 730070 (China) and State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi' an 710072 (China); Deng Zhepeng; Guo Ruibin [Key Laboratory of Eco-Environment-Related Polymer Materials, Ministry of Education of China, Key Laboratory of Polymer Materials of Gansu Province, College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou 730070 (China); Fu Qiangang [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi' an 710072 (China); Feng Chao; Liu Pengwei; Sun Yu [Key Laboratory of Eco-Environment-Related Polymer Materials, Ministry of Education of China, Key Laboratory of Polymer Materials of Gansu Province, College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou 730070 (China)

    2012-01-25

    Highlights: Black-Right-Pointing-Pointer A novel high temperature sensitive fluorescent CNTs/Eu{sub 2}O{sub 3} nanocomposite was fabricated. Black-Right-Pointing-Pointer The nanocomposite showed strong fluorescent emission peaks at around 540 and 580 nm after calcined beyond 620 Degree-Sign C for 4 h. Black-Right-Pointing-Pointer The ultrahigh fluorescence intensity of the nanocomposites resulted from a synergetic effect of CNTs and europium oxide. Black-Right-Pointing-Pointer We also discovered that CNTs had an effect of fluorescence quenching. - Abstract: A novel high temperature sensitive fluorescent nanocomposite has been successfully synthesized by an economic hydrothermal method using carbon nanotubes (CNTs), europium oxide, and sodium dodecyl benzene sulfonate (SDBS). To our great interest, the nanocomposites show high temperature sensitivity after calcinations at various temperatures, suggesting a synergetic effect of CNTs and europium oxide which leads to ultrahigh fluorescence intensity of europium oxide nanotubes. When the novel high temperature sensitive fluorescent nanocomposites were calcined beyond 620 Degree-Sign C for 4 h, the obtained nanocomposites have a strong emission peak at around 540 and 580 nm, due to the {sup 5}D{sub 0} {yields} {sup 7}F{sub j} (j = 0, 1) forced electric dipole transition of Eu{sup 3+} ions. In turn, the emission spectra showed a slight blue shift. The intensity of this photoluminescence (PL) band is remarkably temperature-dependent and promotes strongly beyond 620 Degree-Sign C. This novel feature is attributed to the thermally activated carrier transfer process from nanocrystals and charged intrinsic defects states to Eu{sup 3+} energy levels. The novel high temperature sensitive fluorescent nanocomposite has potential applications in high temperature warning materials, sensors and field emission displays. It is also interesting to discover that CNTs have the effect of fluorescence quenching.

  14. Optical and magnetization studies on europium based iron pnictides

    Energy Technology Data Exchange (ETDEWEB)

    Zapf, Sina Maria Ute

    2015-07-01

    The investigations carried out in the framework of this thesis mainly concentrate on europium based iron pnictides. These are a peculiar member of the 122 family as they develop at low temperatures (∝20K) an additional magnetic order of the local rare earth moments. Therefore, europium based iron pnictides provide a unique platform to study the interplay of structural, magnetic and electronic effects in high-temperature superconductors. For this challenging purpose, we have employed SQUID magnetometry and Fourier-transform infrared spectroscopy on EuFe{sub 2}(As{sub 1-x}P{sub x}){sub 2} single crystals. By systematic studies of the in- and out-of-plane magnetic properties of a series of single crystals, we derived the complex magnetic phase diagram of europium based iron pnictides, which contains an A-type antiferromagnetic and a re-entrant spin glass phase. Furthermore, we have investigated the magneto-optical properties of EuFe{sub 2}As{sub 2}, revealing a much more complex magnetic detwinning process than expected. These studies demonstrate a remarkable interdependence between magnetic, electronic and structural effects that might be very important to understand the unconventional superconductivity in these fascinating materials.

  15. Use of europium ions for SAD phasing of lysozyme at the Cu Kα wavelength

    OpenAIRE

    Vijayakumar, Balakrishnan; Velmurugan, Devadasan

    2012-01-01

    Europium(III) ions bound to the surface of hen egg-white lysozyme were found to exhibit good anomalous signal facilitating SAD phasing using laboratory-source data and automated model building. The europium ion-binding sites were observed up to the 15σ level.

  16. Response of boride coating on the Ti-6Al-4V alloy to corrosion and fretting corrosion behavior in Ringer's solution for bio-implant application

    Science.gov (United States)

    Bose, Sivakumar; Pathak, Lokesh Chandra; Singh, Raghuvir

    2018-03-01

    Corrosion and fretting corrosion of boride coating on Ti-6Al-4V (TAV) are investigated in Ringer's solution for bio-implant applications. Boride coatings are fabricated as a function of temperature (900-1100 °C) and soaking time (1-5 h). Coatings are characterized for phase evaluation, microstructural analysis, thickness and microhardness measurement. The coating contained TiB2 and TiB whiskers as outermost and inner layers respectively. The increasing thickness of outer TiB2 at a relatively higher boriding temperature and time impeded the TiB formation. A large microhardness value of ∼3248 Hv15gf at the outermost surface (corrosion resistance of coating produced at increased temperature and time of boriding, yet remained lower than the resistance of bare TAV alloy. The formation of B2O3 and absence of Al2O3 on the surface, as investigated by X-ray photoelectron spectroscopy (XPS), are attributed to an inferior corrosion resistance of the borided TAV. The increase in corrosion resistance with the TiB2 coating thickness is attributed to thickening of the inner passive film formed on borided TAV. A large decrease in fretting damage after boride coating is due to the decline in a synergistic parameter.

  17. Increasing the Surface Hardness of Cast Iron by Electrodeposition of Borides in Molten Salts

    Directory of Open Access Journals (Sweden)

    Al-Azzawi A.H.

    2017-06-01

    Full Text Available In this paper the electrodeposition of boron on the surface of cast iron as a coating is applied to increase the hardness and protect the substrate against abrasive wear. The boron containing coating was synthesized by electrodeposition process from a NaCl-KCl (1:1 mol-10 w%NaF-10w% KBF4 molten salt. The effect of electrolysis parameters (temperature and time on the hardness is presented; the current density varied in the range −37 – −4.5 mA/cm2, allowing perfect coverage of and respect for dimensions. The electrochemical process was carried out at different temperatures (750°C-900°C and for different periods of time (5-10 hours. Depending on the current density and duration of electrolysis, the deposits consist of FeB or Fe2B. Microhardness measurements across the boride layer indicated very high hardness values (between 1600 and 2100 HV0.05. The structure of the boride layer is linked to its boron content and thermal history: as-deposited coatings present very small grain sizes and can be considered as nearly amorphous.

  18. Boron-dependency of molybdenum boride electrocatalysts for the hydrogen evolution reaction

    Energy Technology Data Exchange (ETDEWEB)

    Park, Hyounmyung; Encinas, Andrew; Fokwa, Boniface P.T. [Department of Chemistry, University of California, Riverside, CA (United States); Department of Chemical and Environmental Engineering, University of California, Riverside, CA (United States); Scheifers, Jan P.; Zhang, Yuemei [Department of Chemistry, University of California, Riverside, CA (United States)

    2017-05-08

    Molybdenum-based materials have been considered as alternative catalysts to noble metals, such as platinum, for the hydrogen evolution reaction (HER). We have synthesized four binary bulk molybdenum borides Mo{sub 2}B, α-MoB, β-MoB, and MoB{sub 2} by arc-melting. All four phases were tested for their electrocatalytic activity (linear sweep voltammetry) and stability (cyclic voltammetry) with respect to the HER in acidic conditions. Three of these phases were studied for their HER activity and by X-ray photoelectron spectroscopy (XPS) for the first time; MoB{sub 2} and β-MoB show excellent activity in the same range as the recently reported α-MoB and β-Mo{sub 2}C phases, while the molybdenum richest phase Mo{sub 2}B show significantly lower HER activity, indicating a strong boron-dependency of these borides for the HER. In addition, MoB{sub 2} and β-MoB show long-term cycle stability in acidic solution. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  19. Boron-Dependency of Molybdenum Boride Electrocatalysts for the Hydrogen Evolution Reaction.

    Science.gov (United States)

    Park, Hyounmyung; Encinas, Andrew; Scheifers, Jan P; Zhang, Yuemei; Fokwa, Boniface P T

    2017-05-08

    Molybdenum-based materials have been considered as alternative catalysts to noble metals, such as platinum, for the hydrogen evolution reaction (HER). We have synthesized four binary bulk molybdenum borides Mo2 B, α-MoB, β-MoB, and MoB2 by arc-melting. All four phases were tested for their electrocatalytic activity (linear sweep voltammetry) and stability (cyclic voltammetry) with respect to the HER in acidic conditions. Three of these phases were studied for their HER activity and by X-ray photoelectron spectroscopy (XPS) for the first time; MoB2 and β-MoB show excellent activity in the same range as the recently reported α-MoB and β-Mo2 C phases, while the molybdenum richest phase Mo2 B show significantly lower HER activity, indicating a strong boron-dependency of these borides for the HER. In addition, MoB2 and β-MoB show long-term cycle stability in acidic solution. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Phase Evolution in Boride-Based Cermets and Reaction Bonding onto Plain Low Carbon Steel Substrate

    Science.gov (United States)

    Palanisamy, B.; Upadhyaya, A.

    2012-04-01

    Reaction sinter bonding is a process that aims to bond two materials for improvement in properties through reactive sintering technique. The process has been effectively used to sinter hard materials like borides in situ which not only possess excellent oxidation resistance, good corrosion resistance but also resistant to abrasive wear. Sinter bonding is a unique surface modification process achieved through powder metallurgy and is competent with other techniques like boronizing sintering and sinter-brazing since it eliminates the additional operations of heat treatment and assembly and removes the inherent setbacks with these processes. This study focuses on identifying the phase evolution mechanism using characterization tools like x-ray diffractometry and energy dispersive spectroscopy and study of sinter bonding of the boron containing precursors (Mo-Cr-Fe-Ni-FeB-MoB) onto plain carbon steel. A microstructure containing Fe-based matrix dispersed with complex borides develops with temperature in the tape cast sheets. A fivefold increase in hardness between plain carbon steel in wrought condition and sinter bonded steel was observed. The multilayer consisted of a reaction zone adjacent to the interface and was investigated with the composition profile and hardness measurements. A model of sinter bonding between the cermet and the steel has also been proposed.

  1. Enhancement in red emission at room temperature from europium doped ZnO nanowires by 1,10 phenanthroline-europium interface induced resonant excitations

    Directory of Open Access Journals (Sweden)

    Soumen Dhara

    2017-02-01

    Full Text Available We show that europium doped ZnO nanowires after surface modification with organic ligand, 1,10 phenanthroline (phen leads to strong red emission at 613 nm which is a characteristic emission from the atomic levels of Eu3+. Surface modification with phen leads to formation of phenanthroline-europium interface on the surface of the nanowires due to attachment of Eu3+ ions. After an optimized surface modification with phen, intensity of both the UV emission (band edge and red emission improved by two orders of magnitude at room temperature. We observed multiple energy transfer pathways to the energy levels of Eu3+ ions through the phenanthroline-europium interface, which found to be very effective to the significant enhancement of emission from the dopant Eu3+. This study shows a new insight in to the energy transfer process from phen to the europium doped ZnO system.

  2. Chemical bond in borides. Theoretical and experimental analysis; Chemische Bindung in Boriden. Theoretische und experimentelle Untersuchung

    Energy Technology Data Exchange (ETDEWEB)

    Sagawe, Vanessa

    2013-04-18

    The aim of this work was the analysis of the bonding situation in different borides by examining the electron density in these structures. The main focus of the analysis was on the QTAIM analysis and the evaluation of the Electron Localizability Indicator (ELI-D). For the calculation of the electron density different methods (extended Hueckel, LMTO, (L)APW) were used to prove which method leads to most precise results. The (L)APW-method was found to be the most exact one and the one with the longest computational times. The examined compounds were boron-rich Borides containing icosahedra, Transition Metal Borides and Na{sub 3}B{sub 20}. Most of the structures of the examined boron-rich Borides can be derived directly from the MgB{sub 7} structure type (MgB{sub 7}, MgB{sub 12}C{sub 2}, LiB{sub 13}C{sub 2}, Li{sub 2}B{sub 12}C{sub 2}, LiB{sub 12}PC). The influence of the different cations as well as the interstitial atoms could be analyzed by comparing these compounds. Structures which can be derived from the alpha-rhombohedral Boron were also analyzed (B{sub 12}O{sub 2}, B{sub 12}P{sub 2}, B{sub 12}As{sub 2}). Assuming Bader-Charges the icosahedron is always positively charged if the electronegativity of the interstitial atoms is higher than the electronegativity of the Boron atoms. If their electronegativitiy is lower, the icosahedra are negatively charged. From the ELI-D-basins the bonding situation can be analyzed according to Wade by bisecting the basins of the exohedral bonds. The icosahedra are always negatively charged. However, Wade's rule is never exactly fulfilled as the charge is never exactly -2. To verify the results from theoretical calculations and vice versa, experimental electron density analyses of MgB{sub 7} and Li{sub 2}B{sub 12}C{sub 2} were performed. However, only the examination of MgB{sub 7} gave reliable results. They promoted the results by the calculations and underlined the correctness of the used methods. Results received by single

  3. Wear resistance of laser-deposited boride reinforced Ti-Nb-Zr-Ta alloy composites for orthopedic implants

    Energy Technology Data Exchange (ETDEWEB)

    Samuel, Sonia [Department of Materials Science and Engineering University of North Texas, Denton, TX (United States); Nag, Soumya [Department of Materials Science and Engineering Ohio State University, Columbus, OH (United States); Scharf, Thomas W.; Banerjee, Rajarshi [Department of Materials Science and Engineering University of North Texas, Denton, TX (United States)

    2008-04-01

    The inherently poor wear resistance of titanium alloys limits their application as femoral heads in femoral (hip) implants. Reinforcing the soft matrix of titanium alloys (including new generation {beta}-Ti alloys) with hard ceramic precipitates such as borides offers the possibility of substantially enhancing the wear resistance of these composites. The present study discusses the microstructure and wear resistance of laser-deposited boride reinforced composites based on Ti-Nb-Zr-Ta alloys. These composites have been deposited using the LENS{sup TM} process from a blend of elemental Ti, Nb, Zr, Ta, and boron powders and consist of complex borides dispersed in a matrix of {beta}-Ti. The wear resistance of these composites has been compared with that of Ti-6Al-4V ELI, the current material of choice for orthopedic femoral implants, against two types of counterfaces, hard Si{sub 3}N{sub 4} and softer SS440C stainless steel. Results suggest a substantial improvement in the wear resistance of the boride reinforced Ti-Nb-Zr-Ta alloys as compared with Ti-6Al-4V ELI against the softer counterface of SS440. The presence of an oxide layer on the surface of these alloys and composites also appears to have a substantial effect in terms of enhanced wear resistance.

  4. Simulation of the growth kinetics of the (FeB/Fe 2B) bilayer obtained on a borided stainless steel

    Science.gov (United States)

    Keddam, M.

    2011-01-01

    The present work is an attempt to simulate the growth kinetics of the (FeB/Fe 2B) bilayer grown on a substrate made of AISI 316 stainless steel by the application of the powder-pack boriding process, and using four different temperatures (1123, 1173, 1223 and 1273 K) and five exposure times (2, 4, 6, 8 and 10 h). The adopted diffusion model solves the mass balance equation at each growth front: (FeB/Fe 2B or FeB/substrate) under certain assumptions and without considering the diffusion zone. To consider the effect of the incubation times for the borides formation, the temperature-dependent function ϕ( T) was incorporated in the model. To validate this model, a computer code written in Matlab (version 6.5), was developed with the purpose of simulating the kinetics of the boride layers. This computer code uses the following parameters as input data: (the boriding temperature, the treatment time, the upper and lower limits of boron concentration in each iron boride, the diffusion coefficients of boron in the FeB and Fe 2B phases as well as the ϕ( T) parameter). The outputs of the computer code are the parabolic growth constant at each growth front and the thicknesses of the FeB and Fe 2B layers. A good agreement was obtained between the experimental parabolic growth constants taken from a reference work [I. Campos-Silva et al., Formation and kinetics of FeB/Fe 2B layers and diffusion zone at the surface of AISI 316 borided steels, Surf. Coat Technol., 205 (2010) 403-412] and the simulated values of the parabolic growth constants ( kFeB and k1). The present model was also able to predict the thicknesses of the FeB and Fe 2B layers at a temperature of 1243 K during 3 and 5 h. In addition, the mass gain at the material surface was also estimated as a function of the time and the upper boron content in each iron boride phase. It was shown that the simulated values of the generated mass gain are very sensitive to the increase of both temperature and the upper boron

  5. Dual doped graphene oxide for electrochemical sensing of europium ion

    Science.gov (United States)

    Kumar, Sunil; Patra, Santanu; Madhuri, Rashmi; Sharma, Prashant K.

    2017-05-01

    This present work represents a single step hydrothermal method for the preparation of N, and N, S dual doped graphene oxide (GO). First time, a comparative electrochemical study between single dope and dual doped GO was carried out using potassium ferrocyanide as an electro-active probe molecule and found that the dual doped GO has the highest electrocatalytic activity than single doped, due to the presence of two heteroatoms as a doping material. Afterwards, the dual doped GO was successfully applied for the electrochemical detection of a rare earth element i.e. europium, with LOD value of 5.92 μg L-1.

  6. Crystal growth of nanoscaled europium selenide having characteristic crystal shapes

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Atsushi; Adachi, Taka-aki [Graduate School of Materials Science, Nara Institute of Science and Technology, 8916-5 Takayama, Ikoma, Nara 630-0192 (Japan); Hasegawa, Yasuchika, E-mail: hasegawa@ms.naist.j [Graduate School of Materials Science, Nara Institute of Science and Technology, 8916-5 Takayama, Ikoma, Nara 630-0192 (Japan); Kawai, Tsuyoshi [Graduate School of Materials Science, Nara Institute of Science and Technology, 8916-5 Takayama, Ikoma, Nara 630-0192 (Japan)

    2009-12-04

    Tetrapod-shaped EuSe nanocrystals were prepared through the thermal reduction of europium chloride an organic selenide complex, n-hexadecylamine, and two additives oleic acid and oleylamine. The obtained EuSe nanoparticles were characterized by X-ray diffraction (XRD). The crystal grain size from the XRD spectrum was estimated to be 50 nm. In contrast, observation of the transmission electron microscope (TEM) gave larger sized EuSe (average size: 200 nm). Anisotropic crystal-growth of EuSe nanocrystals was achieved by addition of a small amount of oleic acid in the crystal growth process.

  7. High Temperature Sliding Wear of NiAl-based Coatings Reinforced by Borides

    Directory of Open Access Journals (Sweden)

    Oleksandr UMANSKYI

    2016-05-01

    Full Text Available The development of composite materials (CM in the systems “metal-refractory compound” is one of the up-to-date trends in design of novel materials aimed at operating under the conditions of significant loads at high temperature. To design such material, NiAl, which is widely used for deposition of protective coatings on parts of gas-turbine engines, was selected for a matrix. To strengthen a NiAl under the conditions of intense wear and a broad temperature range (up to 1000 °C, it is reasonable to add refractory inclusions. Introduction of refractory borides into matrix leads to a marked increase in metal wear resistance. In order to research the behavior of the designed composites at high temperatures and to study the influence of oxides on the friction processes, the authors carried out high temperature oxidation of CM of the above systems at 1000 °С for 90 min. It was determined that all of the composites were oxidized selectively and that the thickness of oxide layers formed on the boride inclusions is 3 – 7 times that on the oxides formed on the NiAl matrix. The mechanism of wear of gas-thermal coatings of the NiAl – МеB2 systems was studied for conditions of high temperature tribotests using the «pin-on-disc» technique. The obtained results indicate that introduction of TiB2, CrB2 and ZrB2 leads to their more intense oxidation during high temperature tribotests as compared to the matrix. The oxides formed on refractory borides act as solid lubricants, which promote a decrease in wear of the contact friction pairs. For more detailed investigation of the effect of tribo-oxidation products on the friction processes, tribotests were conducted for prior oxidized (at 900 °С coatings NiAl – 15 wt.% CrB2 (TiB2, ZrB2.DOI: http://dx.doi.org/10.5755/j01.ms.22.1.8093

  8. Photoprotective properties of the fluorescent europium complex in UV-irradiated skin.

    Science.gov (United States)

    Vogt, O; Lademann, J; Rancan, F; Meinke, M C; Schanzer, S; Stockfleth, E; Sterry, W; Lange-Asschenfeldt, B

    2013-01-01

    In this study, we compared the UV-protective abilities of the europium complex compared to titanium dioxide, which represents the most common physical filter for ultraviolet light in the broad-band spectral range. The UV absorption and light transformative capacities of the europium complex were evaluated using a spectrometer with a double-integrating sphere showing that the europium complex does not only absorb and reflect UV light, but transforms it into red and infrared light. It was found that the europium complex binds to the surface of Jurkat cells in vitro. Cells incubated with the europium complex showed a significantly higher viability after UVA and UVB irradiation as compared to untreated cells and cells incubated with titanium dioxide pointing out its photoprotective properties. The europium complex and titanium dioxide show similar penetration capacities into the stratum corneum as tested in human and porcine skin using tape stripping analysis. The europium complex has proved to be an efficient UV filter with a low cyto- and phototoxic profile and therefore represents a potential candidate for use in sunscreen formulations. Copyright © 2013 S. Karger AG, Basel.

  9. Superconductivity in the metal rich Li-Pd-B ternary boride.

    Science.gov (United States)

    Togano, K; Badica, P; Nakamori, Y; Orimo, S; Takeya, H; Hirata, K

    2004-12-10

    Superconductivity at about 8 K was observed in the metal-rich Li-Pd-B ternary system. Structural, microstructural, electrical, and magnetic investigations for various compositions proved that the Li2Pd3B compound, which has an antiperovskite cubic structure composed of distorted Pd6B octahedrons, is responsible for the superconductivity. This is the first observation of superconductivity in metal-rich ternary borides containing alkaline metal and Pd as a late transition metal. The compound prepared by arc melting has a high density and is relatively stable in the air. The upper critical fields H(c2)(0) estimated by linear extrapolation and the Werthamer-Helfand-Hohenberg theory are 6.2 and 4.8 T, respectively.

  10. Toxicogenomic responses of human alveolar epithelial cells to tungsten boride nanoparticles.

    Science.gov (United States)

    Türkez, Hasan; Arslan, Mehmet Enes; Sönmez, Erdal; Tatar, Abdulgani; Açikyildiz, Metin; Geyikoğlu, Fatime

    2017-08-01

    During the recent years, microarray analysis of gene expression has become an inevitable tool for exploring toxicity of drugs and other chemicals on biological systems. Therefore, toxicogenomics is considered as a fruitful area for searching cellular pathways and mechanisms including cancer, immunological diseases, environmental responses, gene-gene interactions and chemical toxicity. In this work, we examined toxic effects of Tungsten Borides NPs on gene expression profiling of the human lung alveolar epithelial cells (HPAEpiC). In line with this purpose, a single crystal of tungsten boride (mixture of WB and W2B) nanoparticles was synthesized by means of zone melting method, and characterized via using X-ray crystallography (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM) and energy-dispersive X-ray spectroscopy (EDX) techniques. Cell viability and cytotoxicity were determined by 3-(4,5-dimethyl-thiazol-2-yl) 2,5-diphenyltetrazolium bromide (MTT), neutral red (NR) and lactate dehydrogenase (LDH) release tests. The whole genome microarray expression analysis was performed to find out the effects of WB and W2B NPs mixture on gene expression of the HPAEpiC cell culture. 123 of 40,000 gene probes were assigned to characterize expression profile for WB/W2B NPs exposure. According to results; 70 genes were up-regulated and 53 genes were down-regulated (≥2 fold change). For further investigations, these genes were functionally classified by using DAVID (The Database for Annotation, Visualization and Integrated Discovery) with gene ontology (GO) analysis. In the light of the data gained from this study, it could be concluded that the mixture of WB/W2B NPs can affect cytokine/chemokine metabolism, angiogenesis and prevent migration/invasion by activating various genes. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Low-voltage cathodoluminescence of europium-activated yttrium orthovanadate

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, M.L.F.

    1995-03-01

    Emissive flat panel display systems operating in full color demand higher performance at low voltages (ca. 501000 V) from cathodoluminescent (CL) phosphors than cathode ray tubes require. Hydrothermal synthesis has been suggested as a route to phosphors with improved efficiencies, lower voltage thresholds, and increased saturation power. This hypothesis was tested in europium-doped yttrium orthovanadate (YVO{sub 4}:Eu), an efficient, red emitting CL phosphor. The CL efficiency of YVO{sub 4}:Eu crystallized from aqueous solution at 200{degrees}C is relatively low until it is annealed. The distribution of particle sizes in the low-temperature phosphor is similar to that in material made via a solid-state route, but crystallites remain much smaller (ca. 400 {Angstrom}) until they are annealed. These observations, along with the anomalously strong dependence of CL intensity on europium concentration, support a model in which efficiency principally depends on crystallite size. CL efficiency of both solid state and hydrothermal YVO{sub 4}:Eu increases with voltage at constant power. Surface-bound electrons are likely the dominant influence on efficiency at voltages near threshold. Saturation power is independent of synthetic route. It is apparent that the CL properties of hydrothermally synthesized YVO{sub 4}:Eu are essentially the same as those of YVO{sub 4}:Eu produced via conventional, high-temperature routes.

  12. In Vivo Toxicity Studies of Europium Hydroxide Nanorods in Mice

    Science.gov (United States)

    Patra, Chitta Ranjan; Abdel Moneim, Soha S.; Wang, Enfeng; Dutta, Shamit; Patra, Sujata; Eshed, Michal; Mukherjee, Priyabrata; Gedanken, Aharon; Shah, Vijay H; Mukhopadhyay, Debabrata

    2009-01-01

    Lanthanide nanoparticles and nanorods have been widely used for diagnostic and therapeutic applications in biomedical nanotechnology due to their fluorescence properties and pro-angiogenic to endothelial cells, respectively. Recently, we have demonstrated that europium (III) hydroxide [EuIII(OH)3] nanorods, synthesized by the microwave technique and characterized by several physico-chemical techniques, can be used as pro-angiogenic agents which introduce future therapeutic treatment strategies for severe ischemic heart/limb disease, and peripheral ischemic disease. The toxicity of these inorganic nanorods to endothelial cells was supported by several in vitro assays. To determine the in vivo toxicity, these nanorods were administered to mice through intraperitoneal injection (IP) everyday over a period of seven days in a dose dependent (1.25 to 125 mgKg−1day−1) and time dependent manner (8–60 days). Bio-distribution of europium elements in different organs was analyzed by inductively coupled plasma mass spectrometry (ICPMS). Short-term (S-T) and long-term (L-T) toxicity studies (mice sacrificed on day 8 and 60 for S-T and L-T, respectively) show normal blood hematology and serum clinical chemistry with the exception of a slight elevation of liver enzymes. Histological examination of nanorod treated vital organs (liver, kidney, spleen and lungs) showed no or only mild histological changes that indicate mild toxicity at the higher dose of nanorods. PMID:19616569

  13. Temperature dependences in electron-stimulated desorption of neutral europium

    CERN Document Server

    Ageev, V N; Madey, T E

    2003-01-01

    The electron-stimulated desorption (ESD) yield for neutral europium (Eu) atoms from Eu layers adsorbed on oxygen-covered tungsten surfaces has been measured as a function of electron energy, europium coverage and degree of oxidation of tungsten, with an emphasis on effects of substrate temperature. The measurements have been carried out using a time-of-flight method and surface ionization detector. We expand on an earlier report, and compare ESD of multivalent Eu with ESD of monovalent alkali atoms, studied previously. The Eu atom ESD is a complicated function of Eu coverage, electron energy and substrate temperature. In the coverage range 0.05-0.35 monolayer (ML), overlapping resonant-like Eu atom yield peaks are observed at electron energies E sub e of 36 and 41 eV that might be associated with Eu or W shallow core level excitations. Additional resonant-like peaks are seen at E sub e of 54 and 84 eV that are associated with W 5p and 5s level excitations. The Eu atom yield peaks at 36 and 41 eV are seen only...

  14. The Oxidation State of Europium in Halide Glasses

    Science.gov (United States)

    Weber, J.K.R.; Vu, M.; Paßlick, C.; Schweizer, S.; Brown, D.E.; Johnson, C.E.; Johnson, J.A.

    2012-01-01

    The luminescent properties of divalent europium ions can be exploited to produce storage phosphors for x-ray imaging applications. The relatively high cost and limited availability of divalent europium halides makes it desirable to synthesize them from the readily available trivalent salts. In this work, samples of pure EuCl3 and fluoride glass melts doped with EuCl3 were processed at 700-800 °C in an inert atmosphere furnace. The Eu oxidation state in the resulting materials was determined using fluorescence and Mössbauer spectroscopy. Heat treatment of pure EuCl3 for 10 minutes at 710 °C resulted in a material comprising approximately equal amounts of Eu2+ and Eu3+. Glasses made using mixtures of EuCl2 and EuCl3 in the starting material contained both oxidation states. This paper describes the sample preparation and analysis and discusses the results in the context of chemical equilibria in the melts. PMID:22101252

  15. Innovative triboluminescence study of multivitamin doped europium tetrakis

    Energy Technology Data Exchange (ETDEWEB)

    Fontenot, R.S. [Alabama A and M University, Department of Physics, Chemistry, and Mathematics, P.O. Box 1268, Normal, Alabama 35762 (United States); University of Louisiana at Lafayette, Department of Physics, P.O. Box 44210, Lafayette, LA 70504 (United States); Bhat, K.N.; Aggarwal, M.D. [Alabama A and M University, Department of Physics, Chemistry, and Mathematics, P.O. Box 1268, Normal, Alabama 35762 (United States); Hollerman, W.A. [University of Louisiana at Lafayette, Department of Physics, P.O. Box 44210, Lafayette, LA 70504 (United States)

    2012-05-15

    As the Space Shuttle program ends, NASA is developing the next generation of space vehicles. These new concept designs will require new and innovative structural health monitoring capabilities. One way to solve this problem is with smart impact sensors that use triboluminescent materials. In 2011, the authors reported an 82% increase in the triboluminescence yield of europium dibenzoylmethide triethylammonium (EuD{sub 4}TEA) by changing the starting material. It has been shown that introduction of dopants tends to enhance the triboluminescent light yield. Here we report the successful synthesis of a multivitamin doped europium tetrakis which appears to be spherical in shape. Inductively Coupled Plasma - Optical Emission Spectroscopy analysis showed the presence of 3.6% calcium, 0.62% magnesium, 0.1% iron, 0.01% copper and manganese. This new product has no shift in the triboluminescent or photoluminescent emission peaks, but only a change in the intensity. In addition, the doped EuD{sub 4}TEA powder statistically emits more triboluminescence while having the same decay time. (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  16. PREFACE: The 16th International Symposium on Boron, Borides and Related Materials (ISBB 2008)

    Science.gov (United States)

    Tanaka, Takaho

    2009-07-01

    This volume of Journal of Physics: Conference Series contains invited and contributed peer-reviewed papers that were presented at the 16th International Symposium on Boron, Borides and Related Materials (ISBB 2008), which was held on 7-12 September 2008, at Kunibiki Messe, Matsue, Japan. This triennial symposium has a half-century long history starting from the 1st meeting in 1959 at Asbury Park, New Jersey. We were very pleased to organize ISBB 2008, which gathered chemists, physicists, materials scientists as well as diamond and high-pressure researchers. This meeting had a strong background in the boron-related Japanese research history, which includes the discovery of superconductivity in MgB2 and development of Nd-Fe-B hard magnets and of YB66 soft X-ray monochromator. The scope of ISBB 2008 spans both basic and applied interdisciplinary research that is centered on boron, borides and related materials, and the collection of articles defines the state of the art in research on these materials. The topics are centered on: 1. Preparation of new materials (single crystals, thin films, nanostructures, ceramics, etc) under normal or extreme conditions. 2. Crystal structure and chemical bonding (new crystal structures, nonstoichiometry, defects, clusters, quantum-chemical calculations). 3. Physical and chemical properties (band structure, phonon spectra, superconductivity; optical, electrical, magnetic, emissive, mechanical properties; phase diagrams, thermodynamics, catalytic activity, etc) in a wide range of temperatures and pressures. 4. Applications and prospects (thermoelectric converters, composites, ceramics, coatings, etc) There were a few discoveries of new materials, such as nanomaterials, and developments in applications. Many contributions were related to 4f heavy Fermion systems of rare-earth borides. Exotic mechanisms of magnetism and Kondo effects have been discussed, which may indicate another direction of development of boride. Two special sessions

  17. Interlayer utilization (including metal borides) for subsequent deposition of NSD films via microwave plasma CVD on 316 and 440C stainless steels

    Science.gov (United States)

    Ballinger, Jared

    Diamond thin films have promising applications in numerous fields due to the extreme properties of diamonds in conjunction with the surface enhancement of thin films. Biomedical applications are numerous including temporary implants and various dental and surgical instruments. The unique combination of properties offered by nanostructured diamond films that make it such an attractive surface coating include extreme hardness, low obtainable surface roughness, excellent thermal conductivity, and chemical inertness. Regrettably, numerous problems exist when attempting to coat stainless steel with diamond generating a readily delaminated film: outward diffusion of iron to the surface, inward diffusion of carbon limiting necessary surface carbon precursor, and the mismatch between the coefficients of thermal expansion yielding substantial residual stress. While some exotic methods have been attempted to overcome these hindrances, the most common approach is the use of an intermediate layer between the stainless steel substrate and the diamond thin film. In this research, both 316 stainless steel disks and 440C stainless steel ball bearings were tested with interlayers including discrete coatings and graded, diffusion-based surface enhancements. Titanium nitride and thermochemical diffusion boride interlayers were both examined for their effectiveness at allowing for the growth of continuous and adherent diamond films. Titanium nitride interlayers were deposited by cathodic arc vacuum deposition on 440C bearings. Lower temperature diamond processing resulted in improved surface coverage after cooling, but ultimately, both continuity and adhesion of the nanostructured diamond films were unacceptable. The ability to grow quality diamond films on TiN interlayers is in agreement with previous work on iron and low alloy steel substrates, and the similarly seen inadequate adhesion strength is partially a consequence of the lacking establishment of an interfacial carbide phase

  18. Photoactive thin films of polycaprolactam doped with europium (III) complex using phenylalanine as ligand

    Energy Technology Data Exchange (ETDEWEB)

    Santos Garcia, Irene Teresinha, E-mail: irene@iq.ufrgs.br [Departamento de Fisico-Quimica, Instituto de Quimica, Universidade Federal do Rio Grande do Sul, Av. Bento Goncalves 9500, Bairro Agronomia, CEP 91501-970, Porto Alegre, RS (Brazil); Velleda Ribeiro, Patricia; Silva Correa, Diogo; Neto da Cunha, Igor Michel; Lenin Villarreal Carreno, Neftali [Instituto de Quimica e Geociencias, Universidade Federal de Pelotas, Campus Capao do Leao, s/n. CEP 96010-900, Pelotas, RS (Brazil); Ceretta Moreira, Eduardo [PPGEE, Universidade Federal do Pampa, Campus Bage, Bage- RS (Brazil); Severo Rodembusch, Fabiano [Departamento de Quimica Organica, Instituto de Quimica, Universidade Federal do Rio Grande do Sul, Av. Bento Goncalves 9500, Bairro Agronomia, CEP 91501-970, Porto Alegre, RS (Brazil)

    2011-12-01

    A photoactive complex based on europium(III) using the amino acid phenylalanine as ligand was prepared and characterized. The obtained europium(III)/phenylalanine complex presents an effective energy transfer from ligands to the rare earth center. The observed photoluminescent behavior for europium(III)/phenylalanine complex was similar to the well known europium(III)/ acetyl-{beta}-acetonate hydrate. New photoactive polyamide thin films were prepared using polycaprolactam as host of these complexes. The structural characterizations of the films were studied through Rutherford backscattering (RBS), Fourier transform infrared (FTIR) and Raman spectroscopies. The polyamide films doped with the amino acid and acetyl-{beta}-acetonate rare earth complexes maintain the original photoluminescent behavior, narrow emission bands corresponding to transitions {sup 5}D{sub 0} {yields} {sup 7}F{sub 0-4}, which indicates that this polymer is an excellent host to these complexes.

  19. Synthesis and luminescence properties of salicylaldehyde isonicotinoyl hydrazone derivatives and their europium complexes.

    Science.gov (United States)

    Shan, Wenfei; Liu, Fen; Liu, Jiang; Chen, Yanwen; Yang, Zehui; Guo, Dongcai

    2015-09-01

    Four novel salicylaldehyde isonicotinoyl hydrazone derivatives and their corresponding europium ion complexes were synthesized and characterized, while the luminescence properties and the fluorescence quantum yields of the target complexes were investigated. The results indicated that the ligands favored energy transfers to the emitting energy level of europium ion, and four target europium complexes showed the characteristic luminescence of central europium ion. Besides the luminescence intensity of the complex with methoxy group, which possessed the highest fluorescence quantum yield (0.522), was stronger than that of other complexes. Furthermore, the electrochemical properties of the target complexes were further investigated by cyclic voltammetry, the results indicated that the highest occupied molecular orbital (HOMO), lowest unoccupied molecular orbital (LUMO) energy levels and the oxidation potential of the complexes with electron donating group increased, however, that of the complexes with accepting electron group decreased. Copyright © 2015 Elsevier Inc. All rights reserved.

  20. [Synthesis and luminescence properties of ternary complexes of europium with aromatic carboxylic acid and acrylonitrile].

    Science.gov (United States)

    Guo, Dong-cai; Yi, Li-ming; Shu, Wan-gen; Zhang, Zhen-zhen; Zeng, Zhao-rong; Zhang, Xi-qian

    2006-11-01

    Five ternary complexes were synthesized from europium with aromatic carboxylic acid (p-methylbenzoic acid, methoxybenzoic acid, m-chlorobenzoic acid and benzoic acid, p-hydroxylbenzoic acid) and acrylonitrile, and characterized by means of elemental analysis, thermal analysis, FTIR spectra and UV spectra. The fluorescence spectra show that five ternary complexes have good luminescence properties, and the sequence of the ability of the aromatic carboxylic acids to transfer light energy to europium ion is as follows: p-methylbenzoic acid>benzoic acid>m-chlorobenzoic acid>p-hydroxylbenzoic acid>methoxybenzoic acid. Meanwhile, the ternary europium complexes containing a reactive ligand acrylonitrile will possibly have a potential application to the fabrication of bonding-type europium polymer luminescent materials.

  1. Corrosion Resistance of Nanopowders of Borides and Carbides of IV-VIB Group Metals in the Nickeling Electrolytes.

    Science.gov (United States)

    Shakhnin, Dmytro; Malyshev, Viktor; Kuschevskaya, Nina; Gab, Angelina

    2017-12-01

    The corrosion resistance of nanopowders of borides and carbides of metals of IV-VIB groups, as well as of silicon carbide, was studied in the standard nickeling electrolytes. As objects of study, nanopowders with the content of the main phase 91.8-97.6% and with the average particle size 32-78 nm were used. Their corrosion resistance was evaluated depending on the acidity of the electrolyte, temperature, and duration of the interaction. It was found that, by the corrosion resistance in the electrolytes solutions, nanopowders of borides and carbides within each group of compounds are similar and characterized by unlimited period of induction in alkaline media. An exception is the nanopowder of silicon carbide which is resistant to the solution of any acidity.

  2. Optical characterization of europium-doped indium hydroxide nanocubes obtained by Microwave-Assisted Hydrothermal method

    OpenAIRE

    Motta, Fabiana Villela da; Marques,Ana Paula de Azevedo; Araújo,Vinícius Dantas de; Tavares, Mara Tatiane De Souza; Delmonte,Mauricio Roberto Bomio; Paskocimas, Carlos Alberto; Li, Máximo Siu; Nascimento, Rubens Maribondo do; Longo, Elson [UNESP

    2014-01-01

    Crystalline europium-doped indium hydroxide (In(OH)3:Eu) nanostructures were prepared by rapid and efficient Microwave-Assisted Hydrothermal (MAH) method. Nanostructures were obtained at low temperature. FE-SEM images confirm that these samples are composed of 3D nanostructures. XRD, optical diffuse reflectance and photoluminescence (PL) measurements were used to characterize the products. Emission spectra of europium-doped indium hydroxide (IH:xEu) samples under excitation (350.7 nm) present...

  3. Structural and optical properties of europium doped zirconia single crystals fibers grown by laser floating zone

    OpenAIRE

    Soares, M.R.N.; Nico, C.; Peres, M.; Ferreira, N.; Fernandes, A.J.S.; Monteiro, T.; COSTA, F.M.

    2011-01-01

    Yttria stabilized zirconia single crystal fibers doped with europium ions were developed envisaging optical applications. The laser floating zone technique was used in order to grow millimetric high quality single crystal fibers. The as-grown fibers are completely transparent and inclusion free, exhibiting a cubic structure. Under ultraviolet (UV) excitation, a broad emission band appears at 551 nm. The europium doped fibers are translucent with a tetragonal structure and exhibit an intense r...

  4. Chemical modeling of mixed occupations and site preferences in anisotropic crystal structures: case of complex intermetallic borides.

    Science.gov (United States)

    Deringer, Volker L; Goerens, Christian; Esters, Marco; Dronskowski, Richard; Fokwa, Boniface P T

    2012-05-21

    Transition-metal borides show not only promising physical properties but also a rich variety of crystal structures. In this context, quantum-chemical tools can shed light on important facets of the chemistry within such intermetallic borides. Using density-functional theory (DFT), we analyze in detail two phases of significant structural-chemical importance: the recently synthesized Ti(1+x)Os(2-x)RuB(2) and the isotypical Ti(1+x)Os(3-x)B(2). Starting from the observation of different Ti/Os occupations in X-ray crystal structure analysis, we assess suitable computational models and rationalize how the interplay of Ti-Ti, Ti-Os, and Os-Os bonds drives the site preferences. Then, we move on to a systematic investigation of the metal-boron bonds which embed the characteristic, trigonal-planar B(4) units within their metallic surroundings. Remarkably, the different Ti-B bonds in Ti(1+x)Os(2-x)RuB(2) (and also in its ternary derivative) are of vastly different strength, and the strength of these bonds does not correlate with their length. The tools presented in this work are based on simple and insightful chemical arguments together with DFT, and may subsequently be transferred to other intermetallic phases--transition-metal borides and beyond.

  5. A non-aqueous reduction process for purifying ¹⁵³Gd produced in natural europium targets.

    Science.gov (United States)

    Johnsen, Amanda M; Soderquist, Chuck Z; McNamara, Bruce K; Fisher, Darrell R

    2013-12-01

    Gadolinium-153 is a low-energy gamma-emitter used in nuclear medicine imaging quality assurance. Produced in nuclear reactors using natural Eu₂O₃ targets, ¹⁵³Gd is radiochemically separated from europium isotopes by europium reduction. However, conventional aqueous europium reduction produces hydrogen gas, a flammability hazard in radiological hot cells. We altered the traditional reduction method, using methanol as the process solvent to nearly eliminate hydrogen gas production. This new, non-aqueous reduction process demonstrates greater than 98% europium removal and gadolinium yields of 90%. © 2013 Elsevier Ltd. All rights reserved.

  6. Intercalated europium metal in epitaxial graphene on SiC

    Science.gov (United States)

    Anderson, Nathaniel A.; Hupalo, Myron; Keavney, David; Tringides, Michael C.; Vaknin, David

    2017-10-01

    X-ray magnetic circular dichroism (XMCD) reveals the magnetic properties of intercalated europium metal under graphene on SiC(0001). The intercalation of Eu nanoclusters (average size 2.5 nm) between graphene and SiC substate are formed by deposition of Eu on epitaxially grown graphene that is subsequently annealed at various temperatures while keeping the integrity of the graphene layer. Using sum-rules analysis of the XMCD of Eu M4 ,5 edges at T =15 K, our samples show paramagnetic-like behavior with distinct anomaly at T ≈90 K, which may be related to the Nèel transition, TN=91 K, of bulk metal Eu. We find no evidence of ferromagnetism due to EuO or antiferromagnetism due to Eu2O3 , indicating that the graphene layer protects the intercalated metallic Eu against oxidation over months of exposure to atmospheric environment.

  7. The structure and hardness of the highest boride of tungsten, a borophene-based compound.

    Science.gov (United States)

    Gonzalez Szwacki, Nevill

    2017-06-22

    Two-dimensional systems have strengthened their position as a key materials for novel applications. Very recently, boron joined the distinguished group of elements confirmed to possess 2D allotropes, named borophenes. In this work, we explore the stability and hardness of the highest borides of tungsten, which are built of borophenes separated by metal atoms. We show that the WB3+x compounds have Vickers hardnesses approaching 40 GPa only for small values of x. The insertion of extra boron atoms is, in general, detrimental to the hardness of WB3 because it leads to the formation of quasi-planar boron sheets that are less tightly connected with the adjacent tungsten layers. Very high concentrations of boron (x ≈ 1), give rise to a soft (Vickers hardness of ~8 GPa) and unstable hP20-WB4 structure that can be considered to be built of quasi-planar boron α-sheets separated by graphitic tungsten layers. By contrast, we show that the formation of tungsten vacancies leads to structures, e.g. W0.75B3+x , with Vickers hardnesses that are not only similar in value to the experimentally reported load-independent hardnesses greater than 20 GPa, but are also less sensitive to variations in the boron content.

  8. 40 CFR 721.9511 - Silicic acid (H6SiO2O7), magnesium, strontium salt(1:1:2), dysprosium and europium-doped.

    Science.gov (United States)

    2010-07-01

    ..., strontium salt(1:1:2), dysprosium and europium-doped. 721.9511 Section 721.9511 Protection of Environment...), magnesium, strontium salt(1:1:2), dysprosium and europium-doped. (a) Chemical substance and significant new..., strontium salt(1:1:2), dysprosium and europium-doped. (PMN P-98-848; CAS No.181828-07-9) is subject to...

  9. Fluorescent lifetime imaging microscopy using Europium complexes improves atherosclerotic plaques discrimination.

    Science.gov (United States)

    Sicchieri, Letícia Bonfante; de Andrade Natal, Rodrigo; Courrol, Lilia Coronato

    2016-10-01

    The objective of this study is to characterize arterial tissue with and without atherosclerosis by fluorescence lifetime imaging microscopy (FLIM) using Europium Chlortetracycline complex (EuCTc) as fluorescent marker. For this study, twelve rabbits were randomly divided into a control group (CG) and an experimental group (EG), where they were fed a normal and hypercholesterolemic diet, respectively, and were treated for 60 days. Cryosections of the aortic arch specimens were cut in a vertical plane, mounted on glass slides, and stained with Europium (Eu), Chlortetracycline (CTc), Europium Chlortetracycline (EuCTc), and Europium Chlortetracycline Magnesium (EuCTcMg) solutions. FLIM images were obtained with excitation at 405 nm. The average autofluorescence lifetime within plaque depositions was ~1.36 ns. Reduced plaque autofluorescence lifetimes of 0.23 and 0.31 ns were observed on incubation with EuCTc and EuCTcMg respectively. It was observed a quenching of collagen, cholesterol and TG emission spectra increasing EuCTc concentration. The drastic reduction in fluorescence lifetimes is due to a resonant energy transfer between collagen, triglycerides, cholesterol and europium complexes, quenching fluorescence.

  10. Visible-light sensitized luminescent europium(III)-β-diketonate complexes: bioprobes for cellular imaging.

    Science.gov (United States)

    Reddy, M L P; Divya, V; Pavithran, Rani

    2013-11-21

    Visible-light sensitized luminescent europium(III) molecular materials are of considerable importance because their outstanding photophysical properties make them well suited as labels in fluorescence-based bioassays and low-voltage driven pure red-emitters in optoelectronic technology. One challenge in this field is development of visible-light sensitizing ligands that can form highly emissive europium(III) complexes with sufficient stability and aqueous solubility for practical applications. Indeed, some of the recent reports have demonstrated that the excitation-window can be shifted to longer-wavelengths in europium(III)-β-diketonate complexes by appropriate molecular engineering and suitably expanded π-conjugation in the complex molecules. In this review, attention is focused on the latest innovations in the syntheses and photophysical properties of visible-light sensitized europium(III)-β-diketonate complexes and their application as bioprobes for cellular imaging. Furthermore, luminescent nanomaterials derived from long-wavelength sensitized europium(III)-β-diketonate complexes and their application in life sciences are also highlighted.

  11. The electronic properties of mixed valence hydrated europium chloride thin film.

    Science.gov (United States)

    Silly, M G; Charra, F; Lux, F; Lemercier, G; Sirotti, F

    2015-07-28

    We investigate the electronic properties of a model mixed-valence hydrated chloride europium salt by means of high resolution photoemission spectroscopy (HRPES) and resonant photoemission spectroscopy (RESPES) at the Eu 3d → 4f and 4d → 4f transitions. From the HRPES spectra, we have determined that the two europium oxidation states are homogeneously distributed in the bulk and that the hydrated salt film is exempt from surface mixed valence transition. From the RESPES spectra, the well separated resonant contributions characteristic of divalent and trivalent europium species (4f(6) and 4f(7) final states, respectively) are accurately extracted and quantitatively determined from the resonant features measured at the two edges. The partial absorption yield spectra, obtained by integrating the photoemission intensity in the valence-band region, can be well reproduced by atomic multiplet calculation at the M(4,5) (3d-4f) absorption edge and by an asymmetric Fano-like shape profile at the N(4,5) (4d-4f) absorption edge. The ratio of Eu(2+) and Eu(3+) species measured at the two absorption edges matches with the composition of the mixed valence europium salt as determined chemically. We have demonstrated that the observed spectroscopic features of the mixed valence salt are attributed to the mixed-valence ground state rather than surface valence transition. HRPES and RESPES spectra provide reference spectra for the study of europium salts and their derivatives.

  12. Europium-doped calcium titanate: Optical and structural evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Mazzo, Tatiana Martelli; Pinatti, Ivo Mateus [INCTMN, LIEC, Departamento de Química, Universidade Federal de São Carlos, P.O. Box 676, 13565-905 São Carlos, SP (Brazil); Macario, Leilane Roberta [INCTMN, LIEC, Instituto de Química, Universidade Estadual Paulista, P.O. Box 355, 14800-900 Araraquara, SP (Brazil); Avansi, Waldir [Centro de Ciências Exatas e de Tecnologia, Departamento de Física, Universidade Federal de São Carlos, Jardim Guanabara, 13565-905 São Carlos, SP (Brazil); Moreira, Mario Lucio [Instituto de Física e Matemática, Universidade Federal de Pelotas, P.O. Box 354, Campus do Capão do Leão, 96001-970 Pelotas, RS (Brazil); Rosa, Ieda Lucia Viana, E-mail: ilvrosa@ufscar.br [INCTMN, LIEC, Departamento de Química, Universidade Federal de São Carlos, P.O. Box 676, 13565-905 São Carlos, SP (Brazil); Mastelaro, Valmor Roberto [Instituto de Física de São Carlos, Departamento de Física e Ciência dos Materiais, Universidade de São Paulo, P.O. Box 369, Av Trabalhador São Carlense 400, 13560-970 São Carlos, SP (Brazil); Varela, José Arana; Longo, Elson [INCTMN, LIEC, Instituto de Química, Universidade Estadual Paulista, P.O. Box 355, 14800-900 Araraquara, SP (Brazil)

    2014-02-05

    Highlights: • CaTiO{sub 3}:Eu{sup 3+} were obtained using low temperatures and very short reactional times. • The Eu{sup 3+} changes the local order–disorder of the [TiO{sub 6}] and [CaO{sub 12}] clusters. • Lifetime decay curves reveal two sites of symmetry of the Eu{sup 3+} in the CT matrix. • CaTiO{sub 3}:Eu{sup 3+} exhibit the strongest luminescent intensity and pure red color. -- Abstract: Pure Calcium Titanate (CT-pure) and Europium doped Calcium Titanate Ca{sub 1−x}Eu{sub x}TiO{sub 3} (x = 0.5%, 1.0% and 2.0% molar ratio of Eu{sup 3+} ions) powders were synthesized by hydrothermal microwave method (HTMW) at 140 °C for 8 min. The HTMW method appears to be an efficient method to prepare the luminescence materials using low temperatures and very short reactional times. In addition it is possible to determine specific correlations imposed by TiCl{sub 4} replacement by titanium isopropoxide [Ti(OC{sub 3}H{sub 7}){sub 4}] changing the reaction character and resulting in two different options of europium doping CT syntesis. To evaluate the influence of the structural order–disorder among the reactions and different properties of these materials, the following techniques were used for characterization. XANES spectroscopy that revealed that the introduction of Eu{sup 3+} ions into the CT lattice induces to significant changes in the local order–disorder around both, [TiO{sub 6}] and [CaO{sub 12}], complex clusters. PL spectra show Eu{sup 3+} emission lines ascribed to the Eu{sup 3+} transitions from {sup 5}D{sub 0} excited states to {sup 7}F{sub J} (J = 0, 1–4) fundamental states in CT:Eu{sup 3+} powders excited at 350 and 394 nm.

  13. Synthesis of Binary Transition Metal Nitrides, Carbides and Borides from the Elements in the Laser-Heated Diamond Anvil Cell and Their Structure-Property Relations

    Science.gov (United States)

    Friedrich, Alexandra; Winkler, Björn; Juarez-Arellano, Erick A.; Bayarjargal, Lkhamsuren

    2011-01-01

    Transition metal nitrides, carbides and borides have a high potential for industrial applications as they not only have a high melting point but are generally harder and less compressible than the pure metals. Here we summarize recent advances in the synthesis of binary transition metal nitrides, carbides and borides focusing on the reaction of the elements at extreme conditions generated within the laser-heated diamond anvil cell. The current knowledge of their structures and high-pressure properties like high-(p,T) stability, compressibility and hardness is described as obtained from experiments. PMID:28824101

  14. Synthesis of Binary Transition Metal Nitrides, Carbides and Borides from the Elements in the Laser-Heated Diamond Anvil Cell and Their Structure-Property Relations

    Directory of Open Access Journals (Sweden)

    Lkhamsuren Bayarjargal

    2011-09-01

    Full Text Available Transition metal nitrides, carbides and borides have a high potential for industrial applications as they not only have a high melting point but are generally harder and less compressible than the pure metals. Here we summarize recent advances in the synthesis of binary transition metal nitrides, carbides and borides focusing on the reaction of the elements at extreme conditions generated within the laser-heated diamond anvil cell. The current knowledge of their structures and high-pressure properties like high-(p; T stability, compressibility and hardness is described as obtained from experiments.

  15. Computational-Experimental Processing of Boride/Carbide Composites by Reactive Infusion of Hf Alloy Melts into B4C

    Science.gov (United States)

    2015-09-16

    PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) UNIVERSITY OF TEXAS AT EL PASO 500 UNIV ST ADMIN BLDG 209 EL PASO, TX 79968-0001 US 8. PERFORMING...Arturo Bronson UNIVERSITY OF TEXAS AT EL PASO Final Report 09/16/2015 DISTRIBUTION A: Distribution approved for public release. AF Office Of Scientific...University of Texas at El Paso July 2015 Bronson-Kumar (University of Texas at El Paso) 1 Computational-Experimental Processing of Boride/Carbide Composites

  16. RBS and RNRA studies on sorption of europium by apatite

    Energy Technology Data Exchange (ETDEWEB)

    Ohnuki, Toshihiko; Kozai, Naofumi; Isobe, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Murakami, Takashi; Yamamoto, Shunya; Aoki, Yasushi; Naramoto, Hiroshi

    1997-03-01

    The sorption mechanism of europium, alternative of trivalent TRU has been studied based on the depth profiles of elements obtained by Rutherford Backscattering Spectroscopy (RBS) and Resonant Nuclear Reaction Analysis (RNRA). The positive peak for Eu and the negative peak for Ca were observed in the subtracted RBS spectra of the apatites on which Eu was sorbed from that of the fresh apatite. This indicates that Eu was sorbed on apatite, while a fraction of Ca was released from apatite. The peak height for Eu in the RBS spectrum of the apatite obtained at 75degC was higher than that of the apatite at 40degC. The depth profile of hydrogen of the apatite on which Eu was sorbed was similar to that of the fresh apatite. The concentration of Eu in the solution decreased with increasing temperature. On the contrary, the concentration of Ca increased with increasing temperature. Thus, it is concluded that a fraction of Eu is exchanged for Ca in the structure of apatite. (author)

  17. Spectrofluorimetric determination of heparin using doxycycline-europium probe

    Energy Technology Data Exchange (ETDEWEB)

    Li Jing [Department of Chemistry, Shandong Normal University, Jinan 250014 (China); Liu Jinkai [Department of Chemistry, Shandong Normal University, Jinan 250014 (China); Zhu Xiaojing [Department of Chemistry, Shandong Normal University, Jinan 250014 (China); Peng Qian [Department of Chemistry, Shandong Normal University, Jinan 250014 (China); Jiang Chongqiu [Department of Chemistry, Shandong Normal University, Jinan 250014 (China)]. E-mail: jiangchongqiu@sdnu.edu.cn

    2005-06-15

    A new spectrofluorimetric method was developed for the determination of the trace amount of heparin (Hep). Using doxycycline (DC)-europium ion (Eu{sup 3+}) as a fluorescent probe, in the buffer solution of pH=8.9, Hep can remarkably enhance the fluorescence intensity of the DC-Eu{sup 3+} complex at {lambda}=612 nm and the enhanced fluorescence intensity of Eu{sup 3+} ion is in proportion to the concentration of Hep. Optimum conditions for the determination of Hep were also investigated. The linear range and detection limit for the determination of Hep are 0.04-0.8 {mu}g/mL and 19.7 ng/mL, respectively. This method is simple, practical, and relatively free of interference from coexisting substances and can be successfully applied to assess Hep in biological samples. By the Rosenthal graphic method, the association constant and binding numbers of Hep with the probe are 6.60x10{sup 4} L/mol and 33.9. Moreover, the enhancement mechanism of the fluorescence intensity in the DC-Eu{sup 3+} system and the DC-Eu{sup 3+}-Hep-CTMAB system have been also discussed.

  18. Extraction of americium and europium by CMPO-substituted adamantylcalixarenes

    Energy Technology Data Exchange (ETDEWEB)

    Babain, V.A.; Alyapyshev, M.Yu.; Karavan, M.D. [V.G. Khlopin Radium Inst., St. Petersburg (Russian Federation); Boehmer, V.; Wang, L. [Johannes Guttenberg Univ., Mainz (Germany); Shokova, E.A.; Motornaya, A.E.; Vatsouro, I.M.; Kovalev, V.V. [M. V. Lomonosov Moscow State Univ., Moscow (Russian Federation)

    2005-07-01

    Eight p-adamantylcalix[4]arene derivatives, bearing four CMPO-like functions [-(CH{sub 2}){sub n}-NH-C(O)-CH{sub 2-}P(O)Ph{sub 2}] at the wide (4a,b, n = 0, 1) or narrow (5a-c and 6a-c, n = 2-4) rims were synthesized for the first time. Studies of the extraction of americium(III) and europium(III) from 3 M HNO{sub 3} solutions to organic phases (dichloromethane, m-nitro-trifluoromethylbenzene) showed: (i) The extraction ability for all the adamantylcalixarene ligands is much better than for their monomeric analogues -N-(1-adamantyl)-, N-(1-adamantylmethyl)- and N,N-(dibutyl)carbamoylmethyldiphenylphosphine oxides 7a, 7b, 8; (ii) The extraction percentage increases strongly with increasing length of the spacer for all types of ligands 4-6, and best extraction results were found for 4b (n = 1) and 5c (n = 4); (iii) The separation coefficient D{sub Am}/D{sub Eu} for the investigated compounds did not exceed 2, which is close to the narrow rim CMPO calixarenes, studied earlier; (iv) Variation of the spacer length between CMPO groups attached to the 1,3- and 2,4-positions of the calixarene platform in 6 did not lead to appreciably improved extractants, neither with respect to the extraction abilities (D) nor to the selectivities (D{sub Am}/D{sub Eu}). (orig.)

  19. Preparation of europium-labelled DNA probes and their properties.

    Science.gov (United States)

    Hurskainen, P; Dahlén, P; Ylikoski, J; Kwiatkowski, M; Siitari, H; Lövgren, T

    1991-01-01

    A chemical method for labelling DNA with a europium chelate is presented. First, primary aliphatic amino groups are introduced onto DNA in a transamination reaction. The transamination reaction is altered by adjusting temperature and duration of the reaction. Subsequently, the modified DNA is reacted with an isothiocyanate derivative of a Eu chelate. The optimum amount of Eu chelates on a DNA probe is 4-8% of total nucleotides. There is a decrease of 0.7 degrees C in the melting temperature of DNA for each incorporated Eu chelate on 100 bases. Hybridization efficiency is lowered by the introduction of Eu chelates but this effect can be partly overcome by using high DNA probe concentrations. The detection limit of the Eu-labelled probe is 0.15 attomoles of target DNA in a mixed-phase hybridization assay on microtitration wells. In addition to high sensitivity the Eu-labelled probes offer convenience in use and results which are quantitative and easy to interpret. PMID:1826948

  20. Chloride, bromide and iodide scintillators with europium doping

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2014-08-26

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  1. Spectrofluorimetric determination of lecithin using a tetracycline-europium probe

    Energy Technology Data Exchange (ETDEWEB)

    Wang Ting [Department of Chemistry, Shandong Normal University, Jinan, Shandong 250014 (China); Jiang Chongqiu [Department of Chemistry, Shandong Normal University, Jinan, Shandong 250014 (China)]. E-mail: jiangchongqiu@sdnu.edu.cn

    2006-03-02

    Trace amount of lecithin (PC) was determined in the buffer solution of pH 5.7, using tetracycline (TC)-europium ion (Eu{sup 3+}) as a fluorescent probe. PC can remarkably enhance the fluorescence intensity of the TC-Eu{sup 3+} complex at {lambda} = 612 nm and the enhanced fluorescence intensity of Eu{sup 3+} is in proportion to the concentration of PC. Optimum conditions for the determination of PC were also investigated. The linear range and detection limit for the determination of PC are 4.0 x 10{sup -7} to 1.4 x 10{sup -5} mol/L and 3.9 x 10{sup -8} mol/L. This method is simple, practical and relatively free of interference from coexisting substances and can be successfully applied to assess PC in serum samples. Moreover, the enhancement mechanism of the fluorescence intensity in the TC-Eu{sup 3+} system, the TC-Eu{sup 3+}-PC system, and the TC-Eu{sup 3+}-PC-sodium dodecyl benzene sulfonate (SDS) system is also discussed.

  2. Artifacts in the determination of the binding of americium and europium to an aquatic fulvic acid

    Energy Technology Data Exchange (ETDEWEB)

    Lead, J.R.; Hamilton-Taylor, J.; Kelly, M. [Institute of Environmental and Biological Sciences, Lancaster University, Lancaster (United Kingdom)

    1995-11-23

    The binding of europium and americium by an aquatic fulvic acid was investigated using an equilibrium ion exchange technique (Schubert`s method). The results for europium were consistent with literature data. Americium gave anomalous results for both the D{sub o} values (partition coefficient of the metal between the resin and solution phases in the absence of the fulvic acid) and D values (partition coefficient of the metal between the resin and solution phases in the presence of the fulvic acid). The values for americium were unexpectedly low and, in the case of D values, only slightly pH dependent. The cause of the discrepancy was found to be the partial dissolution of the resin or the loss of small colloidal material from the resin. The effects on the europium results were minimal due to the use of lower resin weights and higher metal concentrations

  3. Synthesis and luminescence properties of 2-(benzylcarbamoyl)phenyl derivatives and their europium complexes.

    Science.gov (United States)

    Guo, Dongcai; He, Wei; Liu, Bang; Gou, Lining; Li, Ruixia

    2013-01-01

    Six novel 2-(benzylcarbamoyl)phenyl derivatives were synthesized and characterized by (1) H-NMR, mass spectrometry, infrared spectra and elemental analysis. Their europium complexes were prepared and characterized by elemental analysis, EDTA titrimetric analysis, IR and UV spectra as well as molar conductivity measurements. The luminescence properties of these complexes were investigated and results show that 2-(benzylcarbamoyl)phenyl derivatives possess high selectivity and good coordination with the europium ion. Complex Eu-2-(benzylcarbamoyl)phenyl-2-phenylacetate showed green luminescence that was emitted by the ligand of 2-(benzylcarbamoyl)phenyl-2-phenylacetate, while other complexes showed the characteristic red luminescence of europium ion and also possessed high luminescence intensity. Copyright © 2012 John Wiley & Sons, Ltd.

  4. Induction of Circularly Polarized Luminescence from Europium by Amino Acid Based Ionic Liquids.

    Science.gov (United States)

    Zercher, Ben; Hopkins, Todd A

    2016-11-07

    Materials that emit circularly polarized light have application in several important industries. Because they show large optical activity and emit sharp visible light transitions, europium complexes are often exploited in applications that require circularly polarized luminescence (CPL). Chiral and coordinating ionic liquids based on prolinate, valinate, and aspartate anions are used to induce CPL from a simple achiral europium triflate salt. The sign of the induced CPL is dependent on the handedness (l vs d) of the amino acid anion. Comparison of the CPL spectra in ionic liquid with proline and valine vs aspartate shows that the number of carboxylate groups in the amino acid anion influences the europium coordination environment. DFT calculations predict a chiral eight-coordinate Eu(Pro)4- structure in the prolinate ionic liquid and a chiral seven- or eight-coordinate Eu(Asp)33- structure in the aspartate ionic liquid.

  5. Comparative analysis of conjugated alkynyl chromophore-triazacyclononane ligands for sensitized emission of europium and terbium.

    Science.gov (United States)

    Soulié, Marine; Latzko, Frédéric; Bourrier, Emmanuel; Placide, Virginie; Butler, Stephen J; Pal, Robert; Walton, James W; Baldeck, Patrice L; Le Guennic, Boris; Andraud, Chantal; Zwier, Jurriaan M; Lamarque, Laurent; Parker, David; Maury, Olivier

    2014-07-07

    A series of europium and terbium complexes based on a functionalized triazacyclononane carboxylate or phosphinate macrocyclic ligand is described. The influence of the anionic group, that is, carboxylate, methylphosphinate, or phenylphosphinate, on the photophysical properties was studied and rationalized on the basis of DFT calculated structures. The nature, number, and position of electron-donating or electron-withdrawing aryl substituents were varied systematically within the same phenylethynyl scaffold in order to optimize the brightness of the corresponding europium complexes and investigate their two-photon absorption properties. Finally, the europium complexes were examined in cell-imaging applications, and selected terbium complexes were studied as potential oxygen sensors. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Novel class of heterometallic cubane and boride clusters containing heavier group 16 elements.

    Science.gov (United States)

    Thakur, Arunabha; Sao, Soumik; Ramkumar, V; Ghosh, Sundargopal

    2012-08-06

    Thermolysis of an in situ generated intermediate, produced from the reaction of [Cp*MoCl(4)] (Cp* = η(5)-C(5)Me(5)) and [LiBH(4).THF], with excess Te powder yielded isomeric [(Cp*Mo)(2)B(4)TeH(5)Cl] (2 and 3), [(Cp*Mo)(2)B(4)(μ(3)-OEt)TeH(3)Cl] (4), and [(Cp*Mo)(4)B(4)H(4)(μ(4)-BH)(3)] (5). Cluster 4 is a notable example of a dimolybdaoxatelluraborane cluster where both oxygen and tellurium are contiguously bound to molybdenum and boron. Cluster 5 represents an unprecedented metal-rich metallaborane cluster with a cubane core. The dimolybdaheteroborane 2 was found to be very reactive toward metal carbonyl compounds, and as a result, mild pyrolysis of 2 with [Fe(2)(CO)(9)] yielded distorted cubane cluster [(Cp*Mo)(2)(BH)(4)(μ(3)-Te){Fe(CO)(3)}] (6) and with [Co(2)(CO)(8)] produced the bicapped pentagonal bipyramid [(Cp*MoCo)(2)B(3)H(2)(μ(3)-Te)(μ-CO){Co(3)(CO)(6)}] (7) and pentacapped trigonal prism [(Cp*MoCo)(2)B(3)H(2)(μ(3)-Te)(μ-CO)(4){Co(6)(CO)(8)}] (8). The geometry of 8 is an example of a heterometallic boride cluster in which five Co and one Mo atom define a trigonal prismatic framework. The resultant trigonal prism core is in turn capped by two boron, one Te, and one Co atom. In the pentacapped trigonal prism unit of 8, one of the boron atoms is completely encapsulated and bonded to one molybdenum, one boron, and five cobalt atoms. All the new compounds have been characterized in solution by IR, (1)H, (11)B, and (13)C NMR spectroscopy, and the structural types were unambiguously established by crystallographic analysis of 2 and 4-8.

  7. Magnetic and structural properties of yellow europium oxide compound and Eu(OH){sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dongwook, E-mail: dongwookleedl324@gmail.com [Cavendish Laboratory, University of Cambridge, J. J Thomson Av., Cambridge CB3 0HE (United Kingdom); Seo, Jiwon, E-mail: jiwonseo@yonsei.ac.kr [Department of Physics and IPAP, Yonsei University, Seoul 120-749 (Korea, Republic of); Valladares, Luis de los Santos [Cavendish Laboratory, University of Cambridge, J. J Thomson Av., Cambridge CB3 0HE (United Kingdom); Avalos Quispe, O. [Laboratorio de Cerámicos y Nanomateriales, Facultad de Ciencias Físicas, Universidad Nacional Mayor de San Marcos, Ap. Postal 14-0149, Lima, Perú (Peru); Barnes, Crispin H.W. [Cavendish Laboratory, University of Cambridge, J. J Thomson Av., Cambridge CB3 0HE (United Kingdom)

    2015-08-15

    A new material based on a yellow europium oxide compound was prepared from europium oxide in a high vacuum environment. The structural and magnetic properties of the material were investigated. Owing to the absence of a crystal structure, the material exhibited a disordered magnetic behavior. In a reaction with deionized (DI) water without applied heat, the compound assumed a white color as soon as the DI water reached the powder, and the structure became polycrystalline Eu(OH){sub 3}. The magnetic properties, such as the thermal hysteresis, disappeared after the reaction with DI water, and the magnetic susceptibility of the yellow oxide compound weakened. The magnetic properties of Eu(OH){sub 3} were also examined. Although Eu{sup 3+} is present in Eu(OH){sub 3}, a high magnetic moment due to the crystal field effect was observed. - Graphical abstract: (top left) Optical image of the yellow europium oxide compound. (top right) Optical image of the product of DI water and yellow europium oxide. (bottom) Magnetization curves as a function of temperature measured in various magnetic field. - Highlights: • We prepared a new material based on a yellow europium oxide compound from europium oxide. • We characterized the magnetic properties of the material which exhibits a disordered magnetic behavior such as thermal hysteresis. • The compound turned white (Eu(OH){sub 3}) as soon as the DI water reached the powder. • The thermal hysteresis disappeared after the reaction with DI water and the magnetic susceptibility of the yellow oxide compound weakened.

  8. Europium stearate additives delay oxidation of UHMWPE for orthopaedic applications: a pilot study.

    Science.gov (United States)

    Gallardo, Luis A; Carpentieri, Ilenia; Laurent, Michel P; Costa, Luigi; Wimmer, Markus A

    2011-08-01

    Ultrahigh-molecular-weight polyethylene (UHMWPE) is used as an articulating surface in prosthetic devices. Its failure under various mechanisms after oxidation is of utmost concern. Free radicals formed during the sterilization process using high-energy irradiation result in oxidation. Europium, an element of the lanthanide family, has a unique electron configuration with an unusual lack of preference for directional bonding and notable bonding to oxygen. Because of this, it currently is used in studies for stabilization of polymers such as polyvinyl chloride. We asked whether europium stearate could enhance the oxidation resistance after irradiation in nitrogen of UHMWPE. Conventional nonirradiated and gamma-irradiated in nitrogen UHMWPE were compared with polyethylene doped with 375 ppm and 3750 ppm europium(III) stearate under the same treatment conditions. Chemical characterization was performed by Fourier transform infrared (FTIR) microspectroscopy using 200-μm thin films. The oxidation of doped samples with time was compared with that of conventional samples using accelerated oven aging. The types of oxidation products were identified by FTIR and quantified per material and treatment condition as indications of the oxidation level and mechanism. The generation rate of hydroperoxides and ketones was decelerated proportionally with concentration of europium stearates. The oxidative mechanism appeared similar to that of conventional polyethylene with the same types of measurable end products as ketones and hydroperoxides. Yet, the rate of generation of the latter appeared to be slowed down by the action of europium stearate. Europium stearate mixed in UHMWPE decelerated the oxidation reactions triggered by gamma irradiation in nitrogen, seemingly without major alteration of the oxidation mechanism.

  9. Temperature dependent luminescence of a europium complex incorporated in poly(methyl methacrylate).

    Science.gov (United States)

    Liang, Hao; Xie, Fang; Ren, Xiaojun; Chen, Yifa; Chen, Biao; Guo, Fuquan

    2013-12-01

    An europium β-diketonate complex with a dipyrazolyltriazine derivative ligand, Eu(TTA)3DPBT, has been incorporated into poly(methyl methacryate) (PMMA). The influence of temperature on its luminescence properties has been investigated. The fluorescence emission spectra and luminescence lifetimes showed temperature sensitivity. The analysis of the relative intensity ratio (R) of (5)D0 → (7)F2 to (5)D0 → (7)F1 transition and Judd-Ofelt experimental intensity parameters Ω2 indicated that the local structure and asymmetry in the vicinity of europium ions show no obvious change when the temperature is increased. Copyright © 2013 Elsevier B.V. All rights reserved.

  10. Microstructural evaluation of a low carbon steel submitted to boriding treatment pre and post GTAW welding; Avaliacao microestrutural de um aco de baixo carbono submetido ao tratamento de boretacao pre e pos-soldagem GTAW

    Energy Technology Data Exchange (ETDEWEB)

    Pollnow, Edilson Nunes; Osorio, Alice Goncalves, E-mail: edilson.pollnow@hotmail.com, E-mail: osorio.alice@gmail.com [Universidade Federal de Pelotas (CDTec/UFPel), Pelotas, RS (Brazil). Centro de Desenvolvimento Tecnologico; Araujo, Douglas Bezerra de, E-mail: dbaraujo@ufu.br [Universidade Federal de Uberlandia (FEMEC/UFU), Uberlandia, MG (Brazil). Faculdade de Engenharia Mecanica; Passos, Thais Andrezza dos; Souza, Daniel, E-mail: thais.andrezza.passos@gmail.com, E-mail: danielsouza@furg.br [Universidade Federal do Rio Grande (EE/FURG), Rio Grande, RS (Brazil). Escola de Engenharia

    2017-04-15

    Studies on surface engineering area are given great importance due to the improvement that surface modifications provide to materials. With a global market that has the need to provide parts and equipment with extended service life and low cost, to support stringent requests and thus maintain its high performance, surface treatments may bring what was impossible into reality. Among the surface treatments that have received attention recently, we have the thermochemical process of boriding. The boriding process consists of saturate the surface of steels and metal alloys with boron. This saturation provides an increase in the surface properties not inherent to the base metal, such as hardness, resistance to abrasion and corrosion. Although the properties of boriding steels have already been studied, the effects that the boriding process perform on the steel during or after the welding processes are not known. Hence, it is the purpose of this study to evaluate the microstructure of a low carbon steel treated with boriding before and after GTAW welding. The results indicated poor metallurgical weldability of low carbon steel with boride layer, with the presence of solidification cracks. Nonetheless, the steel welded previous to boring treatment presented a more ductile nucleus, with harder surface. Although the values of hardness within the nucleus of the steel had dropped drastically at the welded zone after the boring, the surface of this steel showed higher values of hardness due to the boriding layer. This fact should be considered when applications where wear resistance is needed. (author)

  11. Kinetics of electrolysis current reversal boriding of tool steels in a boron-containing oxychloride melt based on CaCl2

    Science.gov (United States)

    Chernov, Ya. B.; Filatov, E. S.

    2017-08-01

    The kinetics of thermal diffusion boriding in a melt based on calcium chloride with a boron oxide additive is studied using reversed current. The main temperature, concentration, and current parameters of the process are determined. The phase composition of the coating is determined by a metallographic method.

  12. Study of the europium behavior in aqueous media; Estudio sobre el comportamiento del europio en medios acuosos

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez R, E.; Jimenez R, M.; Solache R, M.; Martinez M, V. [Instituto Nacional de Investigaciones Nucleares, Departamento de Quimica, A.P. 18-1027, C.P. 11801 Mexico D.F. (Mexico)

    2000-07-01

    Europium as waste can produce a pollution problem in water that is in contact with it, what would has a heavy environmental impacts, because of the possibilities of diffusion of these wastes from their place of confinement or storage until the geo and biosphere. The solution of such problem requires of a lot of knowledge over the behavior of several chemical elements such as europium in aqueous solutions. In this work it was used a low ion force (0.02 M). The data set will allow extrapolate the hydrolytic behavior of europium in too much minors ion force media, such as the ground waters, including in ion force zero.

  13. High-pressure study on borides, nanocrystals and negative thermal expansion materials

    Science.gov (United States)

    Chen, Bin

    2001-07-01

    By the use of Mao-Bell diamond anvil cell, employed with x-ray diffraction, optical absorption, Raman and Fourier Transform Infrared (FTIR) spectroscopy, iron borides, nanocrystalline Ni, Fe, Ni3Fe, Al2O 3, Negative Thermal Expansion (NTE) materials such as HfW2O 8, ZrW2O8, ZrMo2O8 have been studied under high pressure. The results of a synchrotron x-ray diffraction study of Fe2B under quasi-hydrostatic conditions from 0 to 50 GPa are reported. Over this pressure range, no phase change or disproportionation has been observed. A value of the bulk modulus, K, of 192 +/- 14 GPa and the first pressure derivative of the bulk modulus, K', of 2.6 +/- 0.6, are obtained. The compression is found to be anisotropic, with the a-axis being more incompressible than the c-axis. X-ray diffraction data of nanocrystalline Ni, Fe and Ni3Fe, using a synchrotron source, was collected under nonhydrostatic and quasi-hydrostatic conditions up to 60 GPa. The bulk moduli, of 185.4 +/- 10 GPa, 171 +/- 5 GPa, 179.4 +/- 8.1 GPa, 168.3 +/- 2.6 GPa, are determined from quasi-hydrostatic compression data of nanocrystalline Ni, alpha-Fe, epsilon-Fe and Ni3Fe, respectively, which are found similar to those of large-grained counterparts. Their phase transformations are studied and compared with their bulk counterparts. A new phase of Al2O3 formed by compression of the nanocrystalline gamma-phase has been detected. This high-pressure phase is metastable upon decompression to ambient pressure, and has a bulk modulus of 251 +/- 10 GPa for Al2O3 of 67 nm. From hydrostatic compression, bulk moduli of K67 = 238 +/- 3 GPa and K37 = 172 +/- 3 GPa are obtained for the 67 nm and 37 nm gamma-Al2O3 particles, respectively, which are significantly higher than that found in a previous study of smaller sized nanocrystals of gamma-alumina (K20 = 162 +/- 14 GPa for 20 nm crystallites). High pressure optical absorption, Raman and FTIR measurements are carried out on negative thermal expansion materials: HfW2O8, ZrW2O

  14. Thermodynamic and structural description of europium complexation in 1-octanol - H{sub 2}O solutions

    Energy Technology Data Exchange (ETDEWEB)

    Vu, T.H.; Charbonnel, M.C.; Boubals, N.; Couston, L. [CEA Marcoule, DEN/DRCP/SCPS/LCAM, BP 17171, 30207 Bagnols-sur-Ceze (France); Arnaud, F. [Laboratoire de Chimie Physique, IPHC, 25 rue Becquerel, 67087 Strasbourg (France)

    2008-07-01

    Polydentate N-bearing ligands such as bis-triazinyl-pyridines (BTPs) are interesting extractants for actinide(III)/lanthanide(III) separation. A description of europium complexation in 1-octanol solutions was undertaken to enhance the knowledge of the extraction mechanisms. The first solvation shell for europium(III) nitrate, chloride, and perchlorate with different amounts of water was determined by Time-Resolved Laser-Induced Fluorescence (TRLIF) spectroscopy. Europium nitrate complexation by iPr-BTP was then studied by TRLIF and micro-calorimetry; similar stability constants related to the formation of Eu(BTP){sub 2}{sup 3+} and Eu(BTP){sub 3}{sup 3+} were obtained by both techniques (log({beta}{sub 2}) = 9.0 {+-} 0.3 and log({beta}{sub 3}) = 13.8 {+-} 0.2). The presence of water in the octanol diluent has an influence on solvation of europium and also on the [Eu(BTP){sub 2}{sup 3+}] / [Eu(BTP){sub 3}{sup 3+}] ratio. (authors)

  15. A novel biocompatible europium ligand for sensitive time-gated immunodetection.

    Science.gov (United States)

    Sayyadi, Nima; Connally, Russell E; Try, Andrew

    2016-01-21

    We describe the synthesis of a novel hydrophilic derivative of a tetradentate β-diketone europium ligand that was used to prepare an immunoconjugate probe against Giardia lamblia cysts. We used a Gated Autosynchronous Luminescence Detector (GALD) to obtain high quality delayed luminescence images of cells 30-fold faster than ever previously reported.

  16. Europium-doped barium halide scintillators for x-ray and ?-ray detections

    NARCIS (Netherlands)

    Selling, J.; Birowosuto, M.D.; Dorenbos, P.; Schweizer, S.

    2007-01-01

    Single crystals of undoped or europium-doped barium chloride, bromide, and iodide were investigated under x-ray and ?-ray excitations. The Eu2+-related x-ray excited luminescence found in the Eu-doped barium halides occurs at 402, 404, and 425?nm for the chloride, bromide, and iodide, respectively.

  17. A europium luminescence assay of lactate and citrate in biological fluids†

    Science.gov (United States)

    Pal, Robert; Costello, Leslie C.

    2013-01-01

    Ratiometric methods of analysis have been developed for the selective determination of lactate or citrate in microlitre samples of human serum, urine or prostate fluids following comparison of anion binding affinities for a family of nine luminescent europium(III) complexes. PMID:19343236

  18. Molecular interactions of Leucoagaricus naucinus with uranium(VI) and europium(III)

    Energy Technology Data Exchange (ETDEWEB)

    Wollenberg, Anne; Raff, Johannes [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Biogeochemistry; Guenther, A. [Helmholtz Institute Freiberg for Resource Technology, Freiberg (Germany)

    2017-06-01

    With regard to a molecular understanding of the interaction of fungal mycelium with radionuclides and its possible application for precautionary radiation protection and bio-remediation, the binding mechanism of the radionuclide uranium and the metal europium, as surrogate for trivalent actinides, where investigated with different starting conditions by the living fungal cells of Leucoagaricus naucinus.

  19. Europium doped In(Zn)P/ZnS colloidal quantum dots

    NARCIS (Netherlands)

    Thuy, Ung Thi Dieu; Maurice, Axel; Liem, Nguyen Quang; Reiss, Peter

    2013-01-01

    Chemically synthesised In(Zn)P alloy nanocrystals are doped with Eu(3+) ions using europium oleate as a molecular precursor and are subsequently covered with a ZnS shell. The presence of zinc in the synthesis of the InP core nanocrystals leads to the formation of an In(Zn)P alloy structure, making

  20. NO fluorescence sensing by europium tetracyclines complexes in the presence of H2O2.

    Science.gov (United States)

    Simões, Eliana F C; Leitão, João M M; Esteves da Silva, Joaquim C G

    2013-07-01

    The effect on the fluorescence of the europium:tetracycline (Eu:Tc), europium:oxytetracycline (Eu:OxyTc) and europium:chlortetracycline (Eu:ClTc) complexes in approximately 2:1 ratio of nitric oxide (NO), peroxynitrite (ONOO(-)), hydrogen peroxide (H2O2) and superoxide (O2 (·-)) was assessed at three ROS/RNS concentrations levels, 30 °C and pH 6.00, 7.00 and 8.00. Except for the NO, an enhancement of fluorescence intensity was observed at pH 7.00 for all the europium tetracyclines complexes-the high enhancement was observed for H2O2. The quenching of the fluorescence of the Tc complexes, without and with the presence of other ROS/RNS species, provoked by NO constituted the bases for an analytical strategy for NO detection. The quantification capability was evaluated in a NO donor and in a standard solution. Good quantification results were obtained with the Eu:Tc (3:1) and Eu:OxyTc (4:1) complexes in the presence of H2O2 200 μM with a detection limit of about 3 μM (Eu:OxyTc).

  1. Long-term tagging of elvers, Anguilla anguilla, with radioactive europium

    DEFF Research Database (Denmark)

    Hansen, Heinz Johs. Max; Fattah, A. T. A.

    1986-01-01

    -life of added europium of 1.6 .+-. 0.5 years. Thirteen hundred 155Eu-labelled elvers (50 Bq per eel), each weighing on average 0.21 g, were set out near Oskarshamn on the east coast of Sweden in June 1982. Three of these were caught nearby in May 1985 and one was caught in August 1985. They weighed...

  2. ULTRAVIOLET TRANSITIONS IN EUROPIUM STUDIED WITH A FREQUENCY-DOUBLED CW RING DYE-LASER

    NARCIS (Netherlands)

    Eliel, E.R.; Hogervorst, W.; van Leeuwen, K.A.H.; Post, B.H.

    1981-01-01

    High resolution laser spectroscopy has been applied to the study of three ultraviolet transitions in Europium at λ = 294.8, 295.1 and 295.8 nm. The tunable narrowband UV has been generated by intracavity frequency doubling in a cw ring dye laser using a temperate tuned, Brewster angled ADA crystal.

  3. Optical and Morphological Characterization of Sonochemically Assisted Europium Doped Copper (I) Oxide Nanostructures

    Science.gov (United States)

    Cosico, J. A. M.; Ruales, P. K.; Marquez, M. C.

    2017-06-01

    In the age where application of nanotechnology in our society has proven to be eminent, different routes of synthesizing nanoparticles have emerged. In this study nanoparticles of cuprous oxide (Cu2O) doped with different amounts of europium was prepared by using solution precursor route approach with the aid of ultrasonic sound. Copper sulphate and europium (III) nitrate pentahydrate was used as source for copper ions and europium ions respectively. X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FTIR) were used to elucidate the cubic crystal structure and organic impurities present on Cu2Onanoparticles. UV-Vis spectroscopy was used to determine the absorption spectrum of the nanoparticles in the wavelength range of 400nm to 700nm. The bandgap of the undoped and doped Cu2O were found to fall between 2.1eV - 2.3eV. Scanning Electron Microscopy (SEM) coupled with energy dispersive x-ray was used to observe the dendritic and rodlike morphology and the presence of europium in the synthesized Cu2O nanoparticles. The observed effect on the absorbance of Cu2O upon adding Eu and a facile way of synthesizing Cu2O nanoparticles could bring a positive impact on the production of functional devices for optoelectronic and energy applications.

  4. Occurrence of photoluminescence and onion like structures decorating graphene oxide with europium using sodium dodecyl sulfate surfactant

    Science.gov (United States)

    Cedeño, V. J.; Rangel, R.; Cervantes, J. L.; Lara, J.; Alvarado, J. J.; Galván, D. H.

    2017-07-01

    Graphene oxide decoration with europium was carried out using SDS (sodium dodecyl sulfate) as the surfactant. The reaction was performed in a microwave oven and subsequently underwent thermal treatment under hydrogen flow. The results found in the present work demonstrate that through the use of SDS surfactant aggregates of hemi-cylindrical and onion-like structures could be obtained; which propitiate an enhanced synergistic photoluminescence located at the red wavelength. On the other hand, after thermal treatment the aggregates disappear providing a good dispersion of europium, however a decrease in the photoluminescence signal is observed. The graphene oxide decorated with europium was characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Fourier infrared transform spectroscopy (FTIR), RAMAN spectroscopy, x-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) techniques, showing the characteristic features of graphene oxide and europium.

  5. Synthesis, characterization, and properties of reduced europium molybdates and tungstates

    Energy Technology Data Exchange (ETDEWEB)

    Abeysinghe, Dileka [Department of Chemistry and Biochemistry, University of South Carolina, Columbia, SC 29208 (United States); Gerke, Birgit [Institut für Anorganische und Analytische Chemie, Universität Münster , Corrensstrasse 30, Münster D-48149 (Germany); Morrison, Gregory; Hsieh, Chun H.; Smith, Mark D. [Department of Chemistry and Biochemistry, University of South Carolina, Columbia, SC 29208 (United States); Pöttgen, Rainer [Institut für Anorganische und Analytische Chemie, Universität Münster , Corrensstrasse 30, Münster D-48149 (Germany); Makris, Thomas M. [Department of Chemistry and Biochemistry, University of South Carolina, Columbia, SC 29208 (United States); Loye, Hans-Conrad zur, E-mail: zurloye@mailbox.sc.edu [Department of Chemistry and Biochemistry, University of South Carolina, Columbia, SC 29208 (United States)

    2015-09-15

    Single crystals of K{sub 0.094}Eu{sub 0.906}MoO{sub 4}, K{sub 0.097}Eu{sub 0.903}WO{sub 4}, EuWO{sub 4}, and EuMoO{sub 4} were grown from molten chloride fluxes contained in vacuum-sealed fused silica and structurally characterized via single crystal X-ray diffraction. The in situ reduction of Eu{sup 3+} to Eu{sup 2+} was carried out using Mo, W, and Zn as metal reducing agents. All four compounds crystallize in the tetragonal space group of I4{sub 1}/a and adopt the scheelite (CaWO{sub 4}) structure type. The magnetic susceptibility of the reported compounds shows paramagnetic behavior down to 2 K. {sup 151}Eu Mössbauer spectroscopy was used to analyze the relative Eu{sup 2+} and Eu{sup 3+} content of the samples. All the compounds were further characterized by EPR, and UV-vis spectroscopy. - Graphical abstract: TOC Caption Two new reduced europium containing quaternary oxides, K{sub 0.094}Eu{sub 0.906}MoO{sub 4} and K{sub 0.097}Eu{sub 0.903}WO{sub 4}, and two previously reported ternary reduced oxides, EuWO{sub 4} and EuMoO{sub 4}, were synthesized via an in situ reduction of Eu{sup 3+} to Eu{sup 2+} under flux method using Mo, W, and Zn as metal reducing agents. {sup 151}Eu Mössbauer spectroscopy was used to analyze the relative Eu{sup 2+} and Eu{sup 3+} content of the samples. - Highlights: • K{sub 0.094}Eu{sub 0.906}MoO{sub 4}, K{sub 0.097}Eu{sub 0.903}WO{sub 4}, EuWO{sub 4}, and EuMoO{sub 4} have been synthesized and characterized. • The in situ reduction of Eu{sup 3+} to Eu{sup 2+} was carried out using Mo, W, and Zn as metal reducing agents. • Magnetic susceptibility data were collected. • {sup 151}Eu Mössbauer spectroscopy was used to analyze Eu{sup 2+} and Eu{sup 3+} content.

  6. Thermodynamic modelling of phase equilibrium in system Ti-B-Si-C, synthesis and phases composition of borides and carbides layers on titanic alloyVT-1 at electron beam treatment in vacuum

    Science.gov (United States)

    Smirnyagina, N. N.; Khaltanova, V. M.; Lapina, A. E.; Dasheev, D. E.

    2017-01-01

    Composite layers on the basis of carbides and borides the titan and silicon on titanic alloy VT-1 are generated at diffused saturation in vacuum. Formation in a composite of MAX phase Ti3SiC2 is shown. Thermodynamic research of phase equilibrium in systems Ti-Si-C and Ti-B-C in the conditions of high vacuum is executed. The thermodynamics, formation mechanisms of superfirm layers borides and carbides of the titan and silicon are investigated.

  7. A highly sensitive and selective fluorescent sensor for detection of Al(3+) using a europium(III) quinolinecarboxylate.

    Science.gov (United States)

    Xu, Wentao; Zhou, Youfu; Huang, Decai; Su, Mingyi; Wang, Kun; Hong, Maochun

    2014-07-07

    Eu2PQC6 has been developed to detect Al(3+) by monitoring the quenching of the europium-based emission, with the lowest detection limit of ∼32 pM and the quantitative detection range to 150 μM. Eu2PQC6 is the first ever example that the europium(III) complex serves as an Al(3+) fluorescent sensor based on "competition-displacement" mode.

  8. The effect of two additional Eu3+ lumophors in two novel trinuclear europium complexes on their photoluminescent properties.

    Science.gov (United States)

    Yang, Chaolong; Xu, Jing; Ma, Jianying; Zhu, Dongyu; Zhang, Yunfei; Liang, Liyan; Lu, Mangeng

    2013-02-01

    Two novel trinuclear europium complexes based on trisphen(1,3,5-tris{4-((1,10-phenanthroline-[5,6-d]imidazol-2yl)phenoxy)methyl}-2,4,6-trimethyl-benzene) as a second ligand were designed, synthesized, and characterized by FT-IR, (1)H NMR, UV-visible, photoluminescence (PL) spectroscopy, elemental analysis (EA) and ESI-MS. The geometries of these two trinuclear europium complexes were predicted using the Sparkle/PM3 model and suggested a chemical environment of very low symmetry around the lanthanide ions (C(1)), which is in agreement with the luminescent spectra. CV analysis demonstrated that the trinuclear complexes possessed excellent electro-injection abilities. The effects of two additional Eu(3+) lumophors in these trinuclear europium complexes on their photoluminescent properties were investigated in detail. The results indicated that these trinuclear europium complexes exhibited highly luminescent quantum efficiencies and experimental intensity parameters in the solid state. Especially, due to the contribution of the two additional Eu(3+) lumophors in the trinuclear europium complexes, the quantum efficiency of the trinuclear complex Eu(3)(TTA)(9)trisphen was higher (ca. 34%) than the mononuclear europium complex Eu(TTA)(3)imidazophen.

  9. Synthesis, characterization and investigation of thermoelectric properties of selected metal borides; Synthese, Charakterisierung und Untersuchung thermoelektrischer Eigenschaften ausgewaehlter Metallboride

    Energy Technology Data Exchange (ETDEWEB)

    Stober, Frederick

    2012-06-04

    The present work deals with the high-temperature thermoelectric properties of transition metal [eg V, Cr, Mn, Ni, Cu] and lanthanide [e.g. Sc, Y, Gd, Er, Dy]-borides. In particular, intercalation compounds of beta-rhombohedral boron, compounds of the type MB{sub 66}, dodecaborides and hexaborides were examined. In the case of intercalation compounds of beta-rhombohedral boron it was found that the incorporation of metals such as Sc, Mn or Cu result in favorable thermoelectric properties. The reason is most likely the preferred occupation of the metal position M2 instead of M4. Composites, for example, DyB{sub 66}-DyB{sub 12} show high electrical conductivities, high Seebeck effects at high temperatures due to the presence of DyB{sub 12} and low thermal conductivities as a result of the DyB{sub 66} matrix. At 1100K the composite DyB{sub 66}-DyB{sub 12} shows a ZT value of 0.55, thus exceeding the ZT of boron carbide (B{sub 13}C{sub 2}) at this temperature which is considered the best p-type boride material. A composite of ErB{sub 12}-ErB{sub 4}-ErB{sub 2} has negative Seebeck coefficients and shows a ZT value of 0.5 at 840K. Furthermore, the structure of tetragonal Scandiumdodecaboride ScB{sub 12} was solved on the basis of synchrotron data from a crystalline powder, after it has been debated for decades but never fully resolved.

  10. Influence of biofilms on migration of uranium, americium and europium in the environment; Einfluss von Biofilmen auf das Migrationsverhalten von Uran, Americium und Europium in der Umwelt

    Energy Technology Data Exchange (ETDEWEB)

    Baumann, Nils; Zirnstein, Isabel; Arnold, Thuro

    2015-07-01

    The report on the influence of biofilms on migration of uranium, americium and europium in the environment deals with the contamination problems of uranium mines such as SDAG WISMUT in Saxonia and Thuringia. In mine waters microorganisms form a complex microbiological biocoenosis in spite of low pH values and high heavy metal concentrations including high uranium concentrations. The analyses used microbiological methods like confocal laser scanning microscopy and molecular-biological techniques. The interactions of microorganism with fluorescent radioactive heavy metal ions were performed with TRLFS (time resolved laser-induced fluorescence spectroscopy).

  11. Effect of the boride-nitride hardening on the structure and properties of chromium steel deposited with a flux-cored wire

    Science.gov (United States)

    Eremin, E. N.; Losev, A. S.; Borodikhin, S. A.; Ivlev, K. Ye.

    2017-08-01

    Reliability and durability of pipeline valves are largely determined by the resistance of weld sealing surfaces of its shut-off valve, which in its turn depends on the weld metal properties. To improve the durability of valves a new composition of a high chromium flux-cored wire with a boride compounds complex (BN, TiB2, ZrB2) producing weld composite metal is developed. It is stated that the formation of the martensitic matrix with a reduced structural fragments average size due to appearance of dispersed boride-nitride phases in this metal has resulted in high coating hardness and wear resistance. The original version of this article supplied to AIP Publishing was incomplete and omitted the acknowledgement statement. The full acknowledgement reads: The work was carried out at the expense of a grant from the Russian Science Foundation (No. 17-19-01224).

  12. Incorporation of europium III complex into nanoparticles and films obtained by the Sol-Gel methodology

    Directory of Open Access Journals (Sweden)

    Faley Jean de Sousa

    2010-03-01

    Full Text Available The sol-gel process is very effective for the preparation of new materials with potential applications in optics, sensors, catalyst supports, coatings, and specialty inorganic polymers that can be used as hosts for the accommodation of organic molecules. The low temperature employed in the process is the main advantage of this methodology. In this work, the europium (III complex with 1,10-phenantroline was prepared, and this luminescent complex was incorporated into silica nanoparticles and films by the sol-gel process. The nanoparticles were obtained by the modified Stöber methodology. The films were obtained by the dip-coating technique, at different deposition rates and numbers of layers. The nanoparticles and films were characterized by photoluminescence, thermal analysis, and Raman and infrared spectroscopies. Characterization revealed that the europium (III complex was not affected upon incorporation into the nanoparticles and films, opening a new field for the application of these materials.

  13. A Simple and Sensitive Method to Quantify Biodegradable Nanoparticle Biodistribution using Europium Chelates.

    Science.gov (United States)

    Crawford, Lindsey; Higgins, Jaclyn; Putnam, David

    2015-09-08

    The biodistribution of biodegradable nanoparticles can be difficult to quantify. We report a method using time resolved fluorescence (TRF) from a lanthanide chelate to minimize background autofluorescence and maximize the signal to noise ratio to detect biodegradable nanoparticle distribution in mice. Specifically, antenna chelates containing europium were entrapped within nanoparticles composed of polylactic acid-polyethylene glycol diblock copolymers. Tissue accumulation of nanoparticles following intravenous injection was quantified in mice. The TRF of the nanoparticles was found to diminish as a second order function in the presence of serum and tissue compositions interfered with the europium signal. Both phenomena were corrected by linearization of the signal function and calculation of tissue-specific interference, respectively. Overall, the method is simple and robust with a detection limit five times greater than standard fluorescent probes.

  14. A Comprehensive Strategy to Boost the Quantum Yield of Luminescence of Europium Complexes

    Science.gov (United States)

    Lima, Nathalia B. D.; Gonçalves, Simone M. C.; Júnior, Severino A.; Simas, Alfredo M.

    2013-01-01

    Lanthanide luminescence has many important applications in anion sensing, protein recognition, nanosized phosphorescent devices, optoelectronic devices, immunoassays, etc. Luminescent europium complexes, in particular, act as light conversion molecular devices by absorbing ultraviolet (UV) light and by emitting light in the red visible spectral region. The quantum yield of luminescence is defined as the ratio of the number of photons emitted over the number of UV photons absorbed. The higher the quantum yield of luminescence, the higher the sensitivity of the application. Here we advance a conjecture that allows the design of europium complexes with higher values of quantum yields by simply increasing the diversity of good ligands coordinated to the lanthanide ion. Indeed, for the studied cases, the percent boost obtained on the quantum yield proved to be strong: of up to 81%, accompanied by faster radiative rate constants, since the emission becomes less forbidden. PMID:23928866

  15. Assembly of europium organic framework–gold nanoparticle composite thin films on silicon substrate

    Energy Technology Data Exchange (ETDEWEB)

    Deep, Akash, E-mail: dr.akashdeep@gmail.com [Central Scientific Instruments Organisation (CSIR-CSIO), Sector 30 C, Chandigarh 160030 (India); Academy of Scientific and Innovative Research, CSIR-CSIO, Sector 30 C, Chandigarh 160030 (India); Kaur, Rajnish [Central Scientific Instruments Organisation (CSIR-CSIO), Sector 30 C, Chandigarh 160030 (India); Academy of Scientific and Innovative Research, CSIR-CSIO, Sector 30 C, Chandigarh 160030 (India); Kumar, Parveen [Central Scientific Instruments Organisation (CSIR-CSIO), Sector 30 C, Chandigarh 160030 (India); Kumar, Pawan; Paul, A.K. [Central Scientific Instruments Organisation (CSIR-CSIO), Sector 30 C, Chandigarh 160030 (India); Academy of Scientific and Innovative Research, CSIR-CSIO, Sector 30 C, Chandigarh 160030 (India)

    2014-08-28

    Metal organic frameworks are a sub-class of coordination polymers and rapidly generating huge research interests in several technological areas. One of the emerging areas of their potential applications is the photovoltaics. The present study proposes the assembly of europium organic framework–gold nanoparticle nanocomposite thin film on silicon substrate. Microscopic, X-ray diffraction, surface area measurement and thermal studies have indicated the formation of the desired thin film. Spectral studies have been used to highlight their solid state optical property. Current–voltage studies have established semiconducting property of the above thin films. - Highlights: • Thin film of europium organic framework/gold nanoparticles is prepared on silicon. • Fairly homogeneous films with a roughness factor of 5–10 nm are obtained. • Above thin films offer solid-state photoluminescence and semiconducting properties.

  16. Low-cost industrially available molybdenum boride and carbide as “platinum-like” catalysts for the hydrogen evolution reaction in biphasic liquid systems

    OpenAIRE

    Scanlon, Micheal Diarmaid; Bian, Xiaojun; Vrubel, Heron; Amstutz, Véronique; Schenk, Kurt; Hu, Xile; Liu, Baohong; Girault, Hubert

    2013-01-01

    Rarely reported low cost molybdenum boride and carbide microparticles both of which are available in abundant quantities due to their widespread use in industry adsorb at aqueous acid 12 dichloroethane interfaces and efficiently catalyse the hydrogen evolution reaction in the presence of the organic electron donor decamethylferrocene. Kinetic studies monitoring biphasic reactions by UV/vis spectroscopy and further evidence provided by gas chromatography highlight (a) their superior rates of c...

  17. Synthesis and optical features of an europium organic-inorganic silicate hybrid

    Energy Technology Data Exchange (ETDEWEB)

    Franville, A.C.; Zambon, D.; Mahiou, R.; Chou, S.; Cousseins, J.C. [Universite Blaise Pascal, Aubiere (France). Lab. des Materiaux Inorganiques; Troin, Y. [Laboratoire de Chimie des Heterocycles et des Glucides, EA 987, Universite Blaise-Pascal and ENSCCF, F-63177 Aubiere Cedex (France)

    1998-07-24

    A europium organic-inorganic silicate hybrid was synthesized by grafting a coordinative group (dipicolinic acid) to a silicate network precursor (3-aminopropyltriethoxysilane) via a covalent bonding. Sol-gel process and complexation were performed using different experimental conditions. The hybrid materials, in particular the Eu{sup 3+} coordination mode, were characterized by infrared and luminescence spectroscopies. Morphology of the materials and TG analysis showed that grafted silica enhanced thermal and mechanical resistances of the organic part. (orig.) 7 refs.

  18. Development of a microchip Europium nanoparticle immunoassay for sensitive point-of-care HIV detection.

    Science.gov (United States)

    Liu, Jikun; Du, Bingchen; Zhang, Panhe; Haleyurgirisetty, Mohan; Zhao, Jiangqin; Ragupathy, Viswanath; Lee, Sherwin; DeVoe, Don L; Hewlett, Indira K

    2014-11-15

    Rapid, sensitive and specific diagnostic assays play an indispensable role in determination of HIV infection stages and evaluation of efficacy of antiretroviral therapy. Recently, our laboratory developed a sensitive Europium nanoparticle-based microtiter-plate immunoassay capable of detecting target analytes at subpicogram per milliliter levels without the use of catalytic enzymes and signal amplification processes. Encouraged by its sensitivity and simplicity, we continued to miniaturize this assay to a microchip platform for the purpose of converting the benchtop assay technique to a point-of-care test. It was found that detection capability of the microchip platform could be readily improved using Europium nanoparticle probes. We were able to routinely detect 5 pg/mL (4.6 attomoles) of HIV-1 p24 antigen at a signal-to-blank ratio of 1.5, a sensitivity level reasonably close to that of microtiter-plate Europium nanoparticle assay. Meanwhile, use of the microchip platform effectively reduced sample/reagent consumption 4.5 fold and shortened total assay time 2 fold in comparison with microtiter plate assays. Complex matrix substance in plasma negatively affected the microchip assays and the effects could be minimized by diluting the samples before loading. With further improvements in sensitivity, reproducibility, usability, assay process simplification, and incorporation of portable time-resolved fluorescence reader, Europium nanoparticle immunoassay technology could be adapted to meet the challenges of point-of-care diagnosis of HIV or other health-threatening pathogens at bedside or in resource-limited settings. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Green Luminescence of Divalent Europium in the Hydride Chloride EuHCl

    NARCIS (Netherlands)

    Kunkel, Nathalie; Rudolph, Daniel; Meijerink, A; Rommel, Stefan; Weihrich, Richard; Kohlmann, Holger; Schleid, Thomas

    Luminescence properties of divalent europium in the mixed-anion hydride chloride EuHCl were studied for the first time. Olive-green single crystals of EuHCl (PbFCl-type structure: tetragonal, P4/nmm, a = 406.58(3) pm, c = 693.12(5) pm, c/a = 1.705, Z = 2) resulted from the reaction of elemental

  20. Ferromagnetic semiconductor-metal transition in heterostructures of electron doped europium monoxide

    Energy Technology Data Exchange (ETDEWEB)

    Stollenwerk, Tobias

    2013-09-15

    In the present work, we develop and solve a self-consistent theory for the description of the simultaneous ferromagnetic semiconductor-metal transition in electron doped Europium monoxide. We investigate two different types of electron doping, Gadolinium impurities and Oxygen vacancies. Besides the conduction band occupation, we can identify low lying spin fluctuations on magnetic impurities as the driving force behind the doping induced enhancement of the Curie temperature. Moreover, we predict the signatures of these magnetic impurities in the spectra of scanning tunneling microscope experiments. By extending the theory to allow for inhomogeneities in one spatial direction, we are able to investigate thin films and heterostructures of Gadolinium doped Europium monoxide. Here, we are able to reproduce the experimentally observed decrease of the Curie temperature with the film thickness. This behavior is attributed to missing coupling partners of the localized 4f moments as well as to an electron depletion at the surface which leads to a reduction of the number of itinerant electrons. By investigating the influence of a metallic substrate onto the phase transition in Gadolinium doped Europium monoxide, we find that the Curie temperature can be increased up to 20%. However, as we show, the underlying mechanism of metal-interface induced charge carrier accumulation is inextricably connected to a suppression of the semiconductor-metal transition.

  1. Redox electrochemistry of europium fluoride complexes in an equimolar NaCl-KCl melt

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, S.A., E-mail: kuznet@chemy.kolasc.net.ru [Institute of Chemistry, Kola Science Centre RAS, 26 Akademgorodok., 184209 Apatity, Murmansk region (Russian Federation); Gaune-Escard, M. [Ecole Polytechnique, Mecanique Energetique, Technopole de Chateau Gombert, 5 rue Enrico Fermi, 13453 Marseille Cedex 13 (France)

    2011-07-15

    The electrochemical behavior of europium fluoride complexes was studied by different electrochemical methods at a glassy carbon electrode in the temperature range 973-1100 K in the NaCl-KCl melt. The diffusion coefficients of Eu(III) and Eu(II) were determined by linear sweep voltammetry. The standard rate constants of charge transfer for the Eu(III)/Eu(II) redox couple were found on the base cyclic voltammetry, impedance spectroscopy and chronoamperometry data. The formal standard redox potentials E{sub Eu(III)/Eu(II)}{sup *} were obtained by linear sweep and cyclic voltammetry. The electrochemical behavior of europium fluoride and europium chloride complexes in NaCl-KCl melt was compared and discussed in connection with the strength and stability of these complexes. It was shown that the formation of stronger fluoride complexes reduced values of diffusion coefficients, standard rate constants for charge transfer of the Eu(III)/Eu(II) redox couple and shifted the formal standard redox potentials to the more electronegative values.

  2. Lateral flow immunoassay using europium chelate-loaded silica nanoparticles as labels.

    Science.gov (United States)

    Xia, Xiaohu; Xu, Ye; Zhao, Xilin; Li, Qingge

    2009-01-01

    Despite their ease of use, lateral flow immunoassays (LFIAs) often suffer from poor quantitative discrimination and low analytical sensitivity. We explored the use of a novel class of europium chelate-loaded silica nanoparticles as labels to overcome these limitations. Antibodies were covalently conjugated onto europium chelate-loaded silica nanoparticles with dextran as a linker. The resulting conjugates were used as labels in LFIA for detection of hepatitis B surface antigen (HBsAg). We performed quantification with a digital camera and Adobe Photoshop software. We also used 286 clinical samples to compare the proposed method with a quantitative ELISA. A detection limit of 0.03 microg/L was achieved, which was 100 times lower than the colloidal gold-based LFIAs and lower than ELISA. A precise quantitative dose-response curve was obtained, and the linear measurement range was 0.05-3.13 microg/L, within which the CVs were 2.3%-10.4%. Regression analysis of LFIA on ELISA results gave: log (LFIA) = -0.14 log (ELISA) + 1.03 microg/L with r = 0.99 for the quantification of HBsAg in 35 positive serum samples. Complete agreement was observed for the qualitative comparison of 286 clinical samples assayed with LFIA and ELISA. Europium chelate-loaded silica nanoparticle labels have great potential to improve LFIAs, making them useful not only for simple screening applications but also for more sensitive and quantitative immunoassays.

  3. Luminescent solutions and films of new europium complexes with chelating ligands

    Science.gov (United States)

    Kharcheva, Anastasia V.; Ivanov, Alexey V.; Borisova, Nataliya E.; Kaminskaya, Tatiana P.; Patsaeva, Svetlana V.; Popov, Vladimir V.; Yuzhakov, Viktor I.

    2015-03-01

    The development of new complexes of rare earth elements (REE) with chelating organic ligands opens up the possibility of purposeful alteration in the composition and structure of the complexes, and therefore tuning their optical properties. New ligands possessing two pyridine rings in their structure were synthesized to improve coordination properties and photophysical characteristics of REE compounds. Complexes of trivalent europium with novel chelating ligands were investigated using luminescence and absorption spectroscopy, as well as atomic force microscopy. Luminescence properties of new compounds were studied both for solutions and films deposited on the solid support. All complexes exhibit the characteristic red luminescence of Eu (III) ion with the absolute lumenescence quantum yield in polar acetonitrile solution varying from 0.21 to 1.45 % and emission lifetime ranged from 0.1 to 1 ms. Excitation spectra of Eu coordination complexes correspond with absorption bands of chelating ligand. The energy levels of the triplet state of the new ligands were determined from the phosphorescence at 77 K of the corresponding Gd (III) complexes. The morphology of films of europium complexes with different substituents in the organic ligands was investigated by atomic force microscopy (AFM). It strongly depends both on the type of substituent in the organic ligand, and the rotation speed of the spin-coater. New europium complexes with chelating ligands containing additional pyridine fragments represent outstanding candidates for phosphors with improved luminescence properties.

  4. Use of europium ions for SAD phasing of lysozyme at the Cu Kα wavelength.

    Science.gov (United States)

    Vijayakumar, Balakrishnan; Velmurugan, Devadasan

    2013-01-01

    Europium is shown to be a good anomalous scatterer in SAD phasing for solving the structure of biological macromolecules. The large value of the anomalous contribution of europium, f'' = 11.17 e(-), at the Cu Kα wavelength is an advantage in de novo phasing and automated model building. Tetragonal crystals of hen egg-white lysozyme (HEWL) incorporating europium(III) chloride (50 mM) were obtained which diffracted to a resolution of 2.3 Å at a wavelength of 1.54 Å (Cu Kα). The master data set (360° frames) was split and analyzed for anomalous signal-to-noise ratio, multiplicity, completeness, SAD phasing and automated building. The structure solution and model building of the split data sets were carried out using phenix.autosol and phenix.autobuild. The contributions of the Eu ions to SAD phasing using in-house data collection are discussed. This study revealed successful lysozyme phasing by SAD using laboratory-source data involving Eu ions, which are mainly coordinated by the side chains of Asn46, Asp52 and Asp101 together with some water molecules.

  5. Hydrothermal treatment for preparation of europium-lanthanum phosphates and exploration of their fluorescence properties

    Directory of Open Access Journals (Sweden)

    Hiroaki Onoda

    2014-04-01

    Full Text Available Europium-substituted lanthanum phosphates (Eu; 5 mol% were prepared from lanthanum nitrate, europium nitrate, and sodium polyphosphate solutions by a hydrothermal process at 120 and 160 °C up to 8 h. The obtained phosphates were studied using XRD, IR spectroscopy, TG–DTA, and SEM. UV–vis absorbance and reflectance, as well as fluorescence, were estimated as functional properties of these phosphate materials. We found that samples prepared without hydrothermal treatment were amorphous (as indicated by their XRD patterns, whereas those prepared by a hydrothermal treatment contained peaks corresponding to lanthanum orthophosphate, indicating that the hydrothermal process caused the polyphosphate(s to decompose into orthophosphate(s. The TG–DTA curves of the samples prepared by a hydrothermal treatment were different from those of the samples prepared without hydrothermal treatment. All samples reported herein had no specified shape despite using prolonged hydrothermal treatment times. Although the samples prepared without hydrothermal treatment showed only weak fluorescence peaks, those prepared by a hydrothermal treatment showed strong peaks at 556, 590, 615, and 690 nm. These peaks corresponded to transitions from 5D0 to 7F0, 7F1, 7F2, and 7F4, respectively. Collectively, these results indicate that the hydrothermal treatment is a useful method of obtaining europium-substituted lanthanum phosphates with fluorescence properties.

  6. Fabrication of coated graphite electrode for the selective determination of europium (III) ions.

    Science.gov (United States)

    Upadhyay, Anjali; Singh, Ashok Kumar; Bandi, Koteswara Rao; Jain, A K

    2013-10-15

    Preliminary complexation study showed that two ligands (ionophores) (2-((2-phenyl-2-(pyridin-2-yl)hydazono)methyl)pyridine) [L1], (2-((2-phenyl-2-(pyridin-2-yl)hydazono) methyl)phenol) [L2] can act as europium selective electrode. Europium selective coated graphite electrodes (CGE) were prepared by using ligands [L1] and [L2] and their potentiometric characteristics were determined. Membranes having different compositions of poly(vinylchloride) (PVC), the different plasticizers, anionic additives and ionophores were coated onto the graphite surface. The potential response measurements showed that the best performance was exhibited by the proposed CGE. This electrode had the widest working concentration range, Nernstian slope and fast response times of 10s. The selectivity studies showed that this electrode have higher selectivity towards Eu(3+) over a large number of cations. Furthermore, the electrode generated constant potentials in the pH range 2.7-9.0. This electrode can be used to quantify europium in soil, binary mixtures and also used as an indicator electrode in the potentiometric titration of Eu(3+) with EDTA. The proposed electrode was also successfully applied to the determination of fluoride ions in real samples. © 2013 Elsevier B.V. All rights reserved.

  7. Fluorescent Sulfur-Tagged Europium(III) Coordination Polymers for Monitoring Reactive Oxygen Species.

    Science.gov (United States)

    Wang, Huai-Song; Bao, Wen-Jing; Ren, Shi-Bin; Chen, Ming; Wang, Kang; Xia, Xing-Hua

    2015-07-07

    Oxidative stress caused by reactive oxygen species (ROS) is harmful to biological systems and implicated in various diseases. A variety of selective fluorescent probes have been developed for detecting ROS to uncover their biological functions. Generally, the preparation of the fluorescent probes usually undergoes multiple synthetic steps, and the successful fluorescent sensing usually relies on trial-and-error tests. Herein we present a simple way to prepare fluorescent ROS probes that can be used both in biological and environmental systems. The fluorescent europium(III) coordination polymers (CPs) are prepared by simply mixing the precursors [2,2'-thiodiacetic acid and Eu(NO3)3·6H2O] in ethanol. Interestingly, with the increase of reaction temperature, the product undergoes a morphological transformation from microcrystal to nanoparticle while the structure and fluorescent properties retain. The fluorescence of the sulfur-tagged europium(III) CPs can be selectively quenched by ROS, and thus, sensitive and selective monitoring of ROS in aerosols by the microcrystals and in live cells by the nanoparticles has been achieved. The results reveal that the sulfur-tagged europium(III) CPs provide a novel sensor for imaging ROS in biological and environmental systems.

  8. Facile Synthesis, Characterization, and Cytotoxic Activity of Europium-Doped Nanohydroxyapatite

    Science.gov (United States)

    Niño-Martínez, Nereyda; Patiño-Marín, Nuria

    2016-01-01

    The objective of this study was to synthetize europium-doped nanohydroxyapatite using a simple aqueous precipitation method and, thereafter, characterize and impregnate selected samples with 5-fluorouracil in order to explore the properties and the releasing capacity of this material. The nanohydroxyapatite was doped with 3, 5, 10, and 20 wt% of europium. The obtained samples were characterized after they were dried at 80°C and hydrothermal treated at 120°C by 2 hours. The samples were analyzed by transmission electron microscopy, X-ray diffraction analysis, Fourier transform infrared spectroscopy, and photoluminescence. Also, impregnation and release of 5-fluorouracil were assessed in PBS. The toxicity effects of all samples were studied using viability assays on human fibroblasts cells (HGF-1) in vitro. The sizes of the crystallites were about 10–70 nm with irregular morphology and present the phase corresponding to the JCPDS card 9–0432 for hydroxyapatite. The results of the toxicity experiments indicated that doped and undoped powders are biocompatible with fibroblasts cells. Hydroxyapatite samples doped with 5% of europium and loaded with 5-fluorouracil release almost 7 mg/L of the drug after 60 minutes in PBS and decrease the viability of HeLa cells after 24 hours. PMID:27965525

  9. Processing development of 4 tantalum carbide-hafnium carbide and related carbides and borides for extreme environments

    Science.gov (United States)

    Gaballa, Osama Gaballa Bahig

    Carbides, nitrides, and borides ceramics are of interest for many applications because of their high melting temperatures and good mechanical properties. Wear-resistant coatings are among the most important applications for these materials. Materials with high wear resistance and high melting temperatures have the potential to produce coatings that resist degradation when subjected to high temperatures and high contact stresses. Among the carbides, Al4SiC4 is a low density (3.03 g/cm3), high melting temperature (>2000°C) compound, characterized by superior oxidation resistance, and high compressive strength. These desirable properties motivated this investigation to (1) obtain high-density Al4SiC4 at lower sintering temperatures by hot pressing, and (2) to enhance its mechanical properties by adding WC and TiC to the Al4SiC4. Also among the carbides, tantalum carbide and hafnium carbide have outstanding hardness; high melting points (3880°C and 3890°C respectively); good resistance to chemical attack, thermal shock, and oxidation; and excellent electronic conductivity. Tantalum hafnium carbide (Ta4HfC 5) is a 4-to-1 ratio of TaC to HfC with an extremely high melting point of 4215 K (3942°C), which is the highest melting point of all currently known compounds. Due to the properties of these carbides, they are considered candidates for extremely high-temperature applications such as rocket nozzles and scramjet components, where the operating temperatures can exceed 3000°C. Sintering bulk components comprised of these carbides is difficult, since sintering typically occurs above 50% of the melting point. Thus, Ta4 HfC5 is difficult to sinter in conventional furnaces or hot presses; furnaces designed for very high temperatures are expensive to purchase and operate. Our research attempted to sinter Ta4HfC5 in a hot press at relatively low temperature by reducing powder particle size and optimizing the powder-handling atmosphere, milling conditions, sintering

  10. Real-time in situ monitoring via europium emission of the photo-release of antitumor cisplatin from a Eu-Pt complex.

    Science.gov (United States)

    Li, Hongguang; Lan, Rongfeng; Chan, Chi-Fai; Jiang, Lijun; Dai, Lixiong; Kwong, Daniel W J; Lam, Michael Hon-Wah; Wong, Ka-Leung

    2015-09-25

    A water-soluble light-responsive antitumor agent, PtEuL, based on a cisplatin-linked europium-cyclen complex has been synthesized and evaluated for controlled cisplatin release by linear/two-photon excitation in vitro with concomitant turn-on and long-lived europium emission as a responsive traceable signal.

  11. Europium doping induced symmetry deviation and its impact on the second harmonic generation of doped ZnO nanowires

    Science.gov (United States)

    Dhara, Soumen; Imakita, Kenji; Mizuhata, Minoru; Fujii, Minoru

    2014-06-01

    In this work, we investigated the effects of europium doping on the second harmonic generation (SHG) of ZnO nanowires (NWs). A non-monotonic enhancement in the SHG is observed with the increase of the europium concentration. Maximum SHG is observed from the 1 at.% europium doped ZnO NWs with an enhancement factor of 4.5. To understand the underlying mechanism, the effective second order non-linear coefficient (deff) is calculated from the theoretical fitting with consideration of the absorption effect. Microstructural characterization reveals the structural deformation of the ZnO NWs caused by europium doping. We estimated the deviation in the crystal site symmetry around the Eu3+ ions (defined as the asymmetric factor) from photoluminescence measurement and it is found to be strongly correlated with the calculated deff value. A strong linear dependence between the magnitudes of deff and the asymmetric factor suggests that deviation in the local site symmetry of the ZnO crystal by europium doping could be the most probable origin of the observed large second order non-linearity.

  12. Charge growth, dispersion in europium manganite (EuMnO{sub 3-{delta}}) ceramics revealed using opto-impedance probe

    Energy Technology Data Exchange (ETDEWEB)

    Radhakrishnan, S. [Central Electrochemical Research Institute, Karaikudi-630006, T.N. (India); Jagannathan, R., E-mail: jags57_99@yahoo.com [Central Electrochemical Research Institute, Karaikudi-630006, T.N. (India)

    2011-05-19

    Highlights: > In this study, using opto-, magneto-opto impedance techniques, experimental proof for charge growth in europium manganite (EuMnO{sub 3}) near the region of its Neel temperature is presented. > This study gives data related to dielectric properties of europium manganite. > This study may open-up new avenues for investigating the dielectric characteristics of many electronic-ceramics. - Abstract: In this preliminary report, we present the impedance characteristics of poly-crystalline europium manganite, a promising colossal magneto resistance (CMR) system investigated under optical ({approx}5 eV) and magnetic (0.1 T) perturbations yielding some clues on the charge build-up and dispersion processes. This may possibly be resulting from switching between ferromagnetic and anti-ferromagnetic phases through a charge transfer transition mediated process centering Mn{sup 3+/4+} 3d spins thereby meriting a more detailed study correlating with magnetic measurements.

  13. Rapid and accurate tumor-target bio-imaging through specific in vivo biosynthesis of a fluorescent europium complex.

    Science.gov (United States)

    Ye, Jing; Wang, Jianling; Li, Qiwei; Dong, Xiawei; Ge, Wei; Chen, Yun; Jiang, Xuerui; Liu, Hongde; Jiang, Hui; Wang, Xuemei

    2016-04-01

    A new and facile method for rapidly and accurately achieving tumor targeting fluorescent images has been explored using a specifically biosynthesized europium (Eu) complex in vivo and in vitro. It demonstrated that a fluorescent Eu complex could be bio-synthesized through a spontaneous molecular process in cancerous cells and tumors, but not prepared in normal cells and tissues. In addition, the proteomics analyses show that some biological pathways of metabolism, especially for NADPH production and glutamine metabolism, are remarkably affected during the relevant biosynthesis process, where molecular precursors of europium ions are reduced to fluorescent europium complexes inside cancerous cells or tumor tissues. These results proved that the specific self-biosynthesis of a fluorescent Eu complex by cancer cells or tumor tissues can provide a new strategy for accurate diagnosis and treatment strategies in the early stages of cancers and thus is beneficial for realizing precise surgical intervention based on the relevant cheap and readily available agents.

  14. Polystyrene latex particles containing europium complexes prepared by miniemulsion polymerization using bovine serum albumin as a surfactant for biochemical diagnosis.

    Science.gov (United States)

    Aikawa, Tatsuo; Mizuno, Akihiro; Kohri, Michinari; Taniguchi, Tatsuo; Kishikawa, Keiki; Nakahira, Takayuki

    2016-09-01

    Luminescent particles have been attracting significant attention because they can be used in biochemical applications, such as detecting and imaging biomolecules. In this study, luminescent polystyrene latex particles were prepared through miniemulsion polymerization of styrene with dissolved europium complexes in the presence of bovine serum albumin (BSA) and poly(ethylene glycol) monomethoxy methacrylate as surfactants. The solubility of the europium complex in styrene has a strong effect on the yield of the particle. Europium tris(2-thenoyl trifluoroacetonate) di(tri-n-octyl phosphine oxide), which has a high solubility in styrene, was sufficiently incorporated into the polystyrene particles compared to europium tris(2-thenoyl trifluoroacetonate), which has a low solubility in styrene. The luminescence property of the europium complex could remain intact even after its incorporation through the miniemulsion polymerization. In the aqueous dispersion, the resulting particles could emit strong luminescence, which is a characteristic of the europium complex. The antibody fragments were covalently attached to BSA-covered particles after a reaction with a bifunctional linker, N-(6-maleimidocaproyloxy)succinimide. The time-resolved fluoroimmunoassay technique showed that 3.3pg/mL of human α-fetoproteins (AFP) can be detected by using the resulting luminescent particles. An immunochromatographic assay using the resulting particles was also performed as a convenient method to qualitatively detect biomolecules. The detection limit of AFP measured by the immunochromatographic assay was determined to be 2000pg/mL. These results revealed that the luminescent particles obtained in this study can be utilized for the highly sensitive detection of biomolecules and in vitro biochemical diagnosis. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Highly specific ''sensing'' of tryptophan by a luminescent europium(III) complex

    Energy Technology Data Exchange (ETDEWEB)

    Stubenrauch, Jan A.; Mevissen, Christian; Schulte, Marie F.; Bochenek, Steffen; Albrecht, Markus [RWTH Univ. Aachen (Germany). Inst. fuer Organische Chemie; Subramanian, Palani S. [Central Salt and Marine Chemicals, Research Institute (CSRI), Gujarat (India)

    2016-07-01

    The europium(III) complex 1-Cl{sub 3} (S,S-2,2{sup '}-(((1,10-phenanthroline-2,9-diyl)bis(methanylylidene))bis (azanylyliden e))bis(3-methylbutanamide)europiumtrichloride) undergoes, only in the presence of the amino acid tryptophan, a change of emission at 615 nm. In the presence of few equivalents of tryptophan, emission of the europium complex is enhanced while it disappears upon addition of large amounts. This behavior can be assigned to displacement of the sensitizing phenanthroline ligand of 1-Cl{sub 2} x Trp in the latter case.

  16. Electron-induced desorption of europium atoms from oxidized tungsten surface: concentration dependence of low-energy peak

    CERN Document Server

    Davydov, S Y

    2002-01-01

    One discusses nature of electron induced desorption of Eu sup 0 europium atoms under E sub e irradiating electron low-energies (approx 30 eV) and peculiarities of yield dependence of Eu sup 0 atoms on their concentration at oxidized tungsten surface. Primary act of vacancy origination in europium adatom inner 5p-shell turned to be the determining stage. Evaluations have shown that just the first of two possible scenarios of ionization (electron intra-atomic to Eu adatom external quasi-level or realise of knocked out electron into vacuum) leads to Eu sup 0 desorption. One determined concentration threshold for yield of Eu sup 0 atoms

  17. A novel route to nanosized molybdenum boride and carbide and/or metallic molybdenum by thermo-synthesis method from MoO 3, KBH 4, and CCl 4

    Science.gov (United States)

    Li, Yuanzhi; Fan, Yining; Chen, Yi

    2003-01-01

    Nanosized molybdenum boride and carbide were synthesized from MoO 3, KBH 4, and CCl 4 by thermo-synthesis method at lower temperature. The relative content of Mo, Mo 2C, and molybdenum boride in the product was decided by the molar ratio between MoO 3, KBH 4, and CCl 4. Increasing the molar ratio of CCl 4 to MoO 3 was favorable to the production of Mo 2C. Increasing the molar ratio of KBH 4 to MoO 3 was favorable to the production of molybdenum boride. By carefully adjusting the reaction conditions and annealing in Ar at 900°C, a single phase of MoB could be obtained.

  18. Optical properties of europium(III) {beta}-diketonate/polymer-doped systems using supercritical carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Gerasimova, V.I., E-mail: vis@srd.sinp.msu.ru [Skobel' tsyn Research Institute of Nuclear Physics, Moscow State University, Leninskie Gory 1-2, GSP-1, 119991 Moscow (Russian Federation); Antoshkov, A.A.; Zavorotny, Yu.S.; Rybaltovskii, A.O. [Skobel' tsyn Research Institute of Nuclear Physics, Moscow State University, Leninskie Gory 1-2, GSP-1, 119991 Moscow (Russian Federation); Lemenovskii, D.A., E-mail: dali@org.chem.msu.ru [Chemistry Department, Moscow State University, Leninskie Gory 1-3, GSP-1, 119991 Moscow (Russian Federation)

    2013-02-15

    The optical properties of fluoropolymers and polypropylene doped with europium(III) {beta}-diketonates Eu(L){sub 3}{center_dot}2H{sub 2}O and Eu(L){sub 3}phen (L: fod=6,6,7,7,8,8,8-heptafluoro-2,2-dimethyl-3,5-octanedionato, bta=4,4,4-trifluoro-1-phenyl-1,3-butanedione, tta=4,4,4-trifluoro-1-(2-thienyl)-1,3-butanedione, and phen=1,10-phenanthroline) using supercritical carbon dioxide were investigated by absorption and emission spectra. A comparative analysis of the PL decay times of Eu{sup 3+} ions in the initial europium (III) {beta}-diketonates and impregnated fluoropolymers was carried out. The supercritical fluid (SCF) impregnation of polymer samples with europium(III) {beta}-diketonates containing 1,10-phenanthroline was found to be obstructed differently depending on the type of ligand in the entire investigated impregnation temperature range (T{sub SCF}=50-90 Degree-Sign S). It is shown that from the variety of Eu(L){sub 3}phen only Eu(fod){sub 3}phen can be introduced into the polymer matrix by this method. - Highlights: Black-Right-Pointing-Pointer The optical properties of polymers doped with Eu{sup 3+} {beta}-diketonates using SC CO{sub 2} were investigated. Black-Right-Pointing-Pointer A comparative analysis of the PL decay times in the initial Eu{sup 3+} {beta}-diketonates and doped polymers was carried out. Black-Right-Pointing-Pointer The SC CO{sub 2} impregnation of polymers with Eu{sup 3+} {beta}-diketonates containing 1,10-phenanthroline was found to be obstructed.

  19. Reverse lyotropic liquid crystals from europium nitrate and P123 with enhanced luminescence efficiency.

    Science.gov (United States)

    Yi, Sijing; Li, Qintang; Liu, Hongguo; Chen, Xiao

    2014-10-02

    Fabrication of lyotropic aggregates containing the lanthanide ions is becoming a preferable way to prepare novel functional materials. Here, the lyotropic liquid crystals (LLCs) of reverse hexagonal, reverse bicontinuous cubic, and lamellar phases have been constructed in sequence directly from the mixtures of Eu(NO3)3·6H2O and Pluronic P123 amphiphilc block copolymer with increasing the salt proportion. Their phase types and structural characteristics were analyzed using polarized optical microscopy (POM) and small-angle X-ray scattering (SAXS) measurements. The driving forces of reverse LLC phase formation were investigated using Fourier-transformed infrared spectroscopy (FTIR) and rheological measurements. The hydrated europium salt was found to act not only as a solvent here, but also as the bridge to form hydrogen bonding between coordinated water molecules and PEO blocks, which played a key role in the reverse LLCs formation. Compared to those in aqueous solutions and solid state, the enhanced luminescence quantum yields and prolonged excited state lifetimes were observed in two europium containing reverse mesophases. The luminescence quenching effect of lanthanide ions was efficiently suppressed, probably due to the substitution of coordinated water molecules by oxyethyl groups of P123 and ordered phase structures of LLCs, where the coordinated europium ions were confined and isolated by PEO blocks. The optimum luminescence performance was then found to exist in the reverse hexagonal phase. The obtained results on such lanthanide-induced reverse LLCs should be referable for designing new luminescent soft materials construction to expand their application fields.

  20. How Do Radionuclides Accumulate in Marine Organisms? A Case Study of Europium with Aplysina cavernicola.

    Science.gov (United States)

    Maloubier, Melody; Shuh, David K; Minasian, Stefan G; Pacold, Joseph I; Solari, Pier-Lorenzo; Michel, Hervé; Oberhaensli, François R; Bottein, Yasmine; Monfort, Marguerite; Moulin, Christophe; Den Auwer, Christophe

    2016-10-04

    In the ocean, complex interactions between natural and anthropogenic radionuclides, seawater, and diverse marine biota provide a unique window through which to examine ecosystem and trophic transfer mechanisms in cases of accidental dissemination. The nature of interaction between radionuclides, the marine environment, and marine species is therefore essential for better understanding transfer mechanisms from the hydrosphere to the biosphere. Although data pertaining to the rate of global transfer are often available, little is known regarding the mechanism of environmental transport and uptake of heavy radionuclides by marine species. Among marine species, sponges are immobile active filter feeders and have been identified as hyperaccumulators of several heavy metals. We have selected the Mediterranean sponge Aplysina cavernicola as a model species for this study. Actinide elements are not the only source of radioactive release in cases of civilian nuclear events; however, their physicochemical transfer mechanisms to marine species remain largely unknown. We have targeted europium(III) as a representative of the trivalent actinides such as americium or curium. To unravel biological uptake mechanisms of europium in A. cavernicola, we have combined radiometric (γ) measurements with spectroscopic (time-resolved laser-induced fluorescence spectroscopy, TRLIFS, and X-ray absorption near-edge structure, XANES) and imaging (transmission electron microscopy, TEM, and scanning transmission X-ray microscopy, STXM) techniques. We have observed that the colloids of NaEu(CO3)2·nH2O formed in seawater are taken up by A. cavernicola with no evidence that lethal dose has been reached in our working conditions. Spectroscopic results suggest that there is no change of speciation during uptake. Finally, TEM and STXM images recorded at different locations across a sponge cross section, together with differential cell separation, indicate the presence of europium particles (around

  1. Trace electrochemical analysis of Europium, Ytterbium, and Cerium at their joint presence in solution

    Directory of Open Access Journals (Sweden)

    Rema Matakova

    2012-03-01

    Full Text Available In the course of several decades at the department of analytical chemistry and chemistry of rare elements there were studied the electrode processes with participation of rare-earth metals (REM in accordance with the long awaiting problem of the development of rare-metal and rare-earth branch of non-ferrous metallurgy of Kazakhstan. With the aim of express and highly sensitive analytical control of raw materials and final product of rare-earth industry there were developed the methods of inversion-voltamperometric determination of low concentrations of europium, ytterbium and cerium under the conditions of their individual and combined presence in the solution.

  2. Synergistic extraction of europium and americium into nitrobenzene by using hydrogen dicarbollylcobaltate and dodecaethylene glycol.

    Science.gov (United States)

    Makrlík, Emanuel; Vaňura, Petr; Selucký, Pavel

    2013-01-01

    Extraction of microamounts of europium and americium by a nitrobenzene solution of hydrogen dicarbollylcobaltate (H+B-) in the presence of dodecaethylene glycol (DDEG, L) has been investigated. The equilibrium data have been explained assuming that the species HL+, H2L2+, ML3+ and MH-1L2+ (M3+ = Eu3+, Am3+; L = DDEG) are extracted into the organic phase. The values of extraction and stability constants of the complex species in nitrobenzene saturated with water have been determined. It was found that in this nitrobenzene medium, the stability constant of the EuL3+ complex is comparable with that of AmL3+.

  3. Red/blue electroluminescence from europium-doped organic light emitting diodes

    Science.gov (United States)

    Hagen, Joshua A.; Li, Wayne X.; Grote, James G.; Steckl, Andrew J.

    2006-02-01

    Red/Blue emitting organic light emitting diodes (OLED) devices have been obtained using a Europium-doped organic emitting layer (NPB:Eu). The Eu-doped OLEDs emit in 2 color ranges: a broad blue (~420-500nm) band due to NPB emission and a narrow red peak at 620nm due to Eu emission. The red/blue devices achieve a brightness ~13x more intense than a similarly structured green (Alq 3) emitting OLED. These NPB:Eu emitting structures also reach a maximum efficiency of 0.2 cd/A at brightnesses above 100 cd/m2.

  4. Test of zircon materials for sorption of europium; Pruebas de materiales circoniferos para sorcion de europio

    Energy Technology Data Exchange (ETDEWEB)

    Ordonez R, E.; Fernandez V, S.M.; Garcia R, G. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    In previous works it has already been made notice that some phosphates have the property of sipping radioactive metals in solution, what takes advantage to fabricate reactive barriers that are placed in the repositories of nuclear wastes. In our laboratory it has been obtained to the zirconium silicate (ZrSiO{sub 4}) and the alpha zirconium hydrogen phosphate (Zr(HPO{sub 4}) 2H{sub 2}0) starting from sea sand in an easy and economic way. With the interest of knowing if these compounds can be used in contention barriers the evaluation of their surface properties it is made and of europium sorption. (Author)

  5. Sol-Gel Synthesis, X-Ray Diffraction Studies, and Electric Conductivity of Sodium Europium Silicate

    Directory of Open Access Journals (Sweden)

    Ekaterina V. Borisova

    2013-01-01

    Full Text Available Sodium europium silicate, NaEu9(SiO46O2, with apatite structure has been obtained and studied using X-ray diffraction and SEM. It has been shown that sodium sublimation does not take place upon synthesis by the sol-gel method. Rietveld refinement has revealed that sodium atoms are ordered and occupy the 4f position. O(4 atoms not related to silicate ions are placed at the centers of Eu(2 triangles. DC and AC electric conductivity and activation energy have been determined for the compound studied.

  6. New Class of Bright and Highly Stable Chiral Cyclen Europium Complexes for Circularly Polarized Luminescence Applications.

    Science.gov (United States)

    Dai, Lixiong; Lo, Wai-Sum; Coates, Ian D; Pal, Robert; Law, Ga-Lai

    2016-09-06

    High glum values of +0.30 (ΔJ = 1, 591 nm, in DMSO) and -0.23 (ΔJ = 1, 589 nm, in H2O) were recorded in our series of newly designed macrocyclic europium(III) complexes. A sterically locking approach involving a bidentate chromophore is adopted to control the formation of one stereoisomer, giving rise to extreme rigidity, high stability, and high emission intensity. The combination of a chiral substituent on a macrocyclic chelate for lanthanide ions opens up new perspectives for the further development of circulary polarized luminescent chiral tags in optical and bioapplications.

  7. A microemulsion preparation of nanoparticles of europium in silica with luminescence enhancement using silver

    Science.gov (United States)

    Ma, Zhi Ya; Dosev, Dosi; Kennedy, Ian M

    2010-01-01

    A facile one-pot microemulsion method has been developed for the synthesis of spherical silver core–silica shell (Ag@SiO2) nanoparticles with europium chelates doped in the shell through a silane agent. The method is significantly more straightforward than other extant methods. Measurements of the luminescent emissions from the Ag@SiO2 nanoparticles, in comparison with control silica nanoparticles without silver cores, showed that the presence of the silver cores can increase the fluorescence intensity approximately 24-fold and decrease the luminescence lifetime. This enhancement offers a potential increase in overall particle detectability with increased fluorophore photostability. PMID:19417456

  8. Metal Controlled Diastereoselective Self-assembly and Circularly Polarized Luminescence of a Chiral Heptanuclear Europium Wheel

    Science.gov (United States)

    Bozoklu, Gülay; Gateau, Christelle; Imbert, Daniel; Pécaut, Jacques; Robeyns, Koen; Filinchuk, Yaroslav; Memon, Farah; Muller, Gilles

    2012-01-01

    The chiral dissymmetric tetradentate ligand SPhbipox (6’-(4-phenyloxazolin-2-yl)-2,2’-bipyridine-6-carboxylic acid) leads to the diastereoselective assembly of a homochiral Eu(III) triangle and of a highly emissive (QY=27%) heptanuclear wheel which is the largest example of chiral luminescent complex of Eu(III) reported to date. We show that the nuclearity of the assembly is controlled by the solvent and the europium cation. All the compounds show large circularly polarized luminescence with an activity which varies with the nature of the assembly (highest for the homochiral trimer). PMID:22548280

  9. A europium(III)-based PARACEST agent for sensing singlet oxygen by MRI

    Science.gov (United States)

    Song, Bo; Wu, Yunkou; Yu, Mengxiao; Zhao, Piyu; Zhou, Cheng; Kiefer, Garry E.

    2013-01-01

    A europium (III) DOTA-tetraamide complex was designed as a MRI sensor of singlet oxygen (1O2). The water soluble, thermodynamically stable complex reacts rapidly with 1O2 to form an endoperoxide derivative that results in an ∼3 ppm shift in the position of the Eu(III)-bound water chemical exchange saturation transfer (CEST) peak. The potential of using this probe to detect accumulation of the endoperoxide derivative in biological media by ratiometric CEST imaging was demonstrated. PMID:23575743

  10. Two-phase zirconium boride thin film obtained by ultra-short pulsed laser ablation of a ZrB{sub 12} target

    Energy Technology Data Exchange (ETDEWEB)

    De Bonis, A., E-mail: angela.debonis@unibas.it [Dipartimento di Scienze, Università della Basilicata, Viale dell’Ateneo Lucano, 10 -85100 Potenza (Italy); Istituto di Metodologie Inorganiche e dei Plasmi, Consiglio Nazionale delle Ricerche, U.O.S. di Potenza, C.da Santa Loja, 85010 Tito Scalo, Potenza (Italy); Santagata, A. [Istituto di Metodologie Inorganiche e dei Plasmi, Consiglio Nazionale delle Ricerche, U.O.S. di Potenza, C.da Santa Loja, 85010 Tito Scalo, Potenza (Italy); Rau, J.V. [Istituto di Struttura della Materia, Consiglio Nazionale delle Ricerche, Via del Fosso del Cavaliere 100, 00133 Rome (Italy); Latini, A. [Università di Roma “La Sapienza”, Dipartimento di Chimica, Piazzale Aldo Moro, 5 -00185 Rome (Italy); Mori, T. [National Institute for Materials Science (NIMS) WPI Materials Nanoarchitectonics Center (MANA), Namiki 1-1, Tsukuba 305-0044 (Japan); Medici, L. [Istituto di Metodologie per le Analisi Ambientali, Consiglio Nazionale delle Ricerche, U.O.S. di Potenza, C.da Santa Loja, 85010 Tito Scalo, Potenza (Italy); Teghil, R. [Dipartimento di Scienze, Università della Basilicata, Viale dell’Ateneo Lucano, 10 -85100 Potenza (Italy)

    2013-10-15

    Two-phase zirconium boride thin films have been obtained by ultra-short pulsed laser ablation (PLA) of a zirconium dodecaboride (ZrB{sub 12}) target performed in vacuum. The ablation source was a frequency doubled (λ = 527 nm) Nd:glass laser with a pulse duration of 250 fs. Laser induced plasma has been studied by ICCD imaging and time and space resolved optical emission spectroscopy (OES), whereas the deposited films have been characterized by atomic force microscopy, scanning electron microscopy, X-Ray diffraction and micro-Raman spectroscopy. The film morphology and composition have been interpreted on the basis of the laser ablation mechanism.

  11. Effect of higher borides and inhomogeneity of oxygen distribution on critical current density of undoped and doped magnesium diboride

    Energy Technology Data Exchange (ETDEWEB)

    Prikhna, T A; Tkach, V M; Savchuk, Ya M; Dub, S N; Moshchil, V E; Kozyrev, A V; Sergienko, N V; Melnikov, V S; Shapovalov, A P [Institute for Superhard Materials of the NASU, 2, Avtozavodskaya Str., Kiev 04074 (Ukraine); Gawalek, W; Wendt, M; Dellith, J; Schmidt, Ch; Habisreuther, T; Litzkendorf, D [Institut fuer Photonische Technologien, Albert-Einstein-Strasse 9, Jena, D-07745 (Germany); Danilenko, N I [Institute for Problems of Materialscience of the National Academy of Sciences of Ukraine, 3, Krzhyzhanivsky Str., Kiev 03142 (Ukraine); Weber, H; Eisterer, M [Atomic Institute of the Austrian Universities, 1020 Vienna (Austria); Vajda, J [Budapest University of Technology and Economics, Budapest, Hungary 1111 Budapest, Egry Jozsef u. 18. (Hungary); Sokolovsky, V, E-mail: prikhna@iptelecom.net.u, E-mail: prikhna@mail.r [Ben-Gurion University of the Negev, P.O.B. 653, Beer-Sheva 84105 (Israel)

    2010-06-01

    The effect of doping with Ti, Ta, SiC in complex with synthesis temperature on the amount and distribution of structural inhomogeneities in MgB{sub 2} matrix of high-pressure-synthesized-materials (2 GPa) which can influence pinning: higher borides (MgB{sub 12}) and oxygen-enriched Mg-B-O inclusions, was established and a mechanism of doping effect on j{sub c} increase different from the generally accepted was proposed. Near theoretically dense SiC-doped material exhibited j{sub c}= 10{sup 6} A/cm{sup 2} in 1T field and H{sub irr} =8.5 T at 20 K. The highest jc in fields above 9, 6, and 4 T at 10, 20, and 25 K, respectively, was demonstrated by materials synthesized at 2 GPa, 600 {sup 0}C from Mg and B without additions (at 20 K j{sub c}= 10{sup 2} A/cm{sup 2} in 10 T field). Materials synthesized from Mg and B taken up to 1:20 ratio were superconductive. The highest j{sub c} (6x10{sup 4} A/cm{sup 2} at 20 K in zero field, H{sub irr}= 5 T) and the amount of SC phase (95.3% of shielding fraction), T{sub c} being 37 K were demonstrated by materials having near MgB{sub 12} composition of the matrix. The materials with MgB{sub 12} matrix had a doubled microhardness of that with MgB{sub 2} matrix (25{+-}1.1 GPa and 13.08{+-}1.07 GPa, at a load of 4.9 N, respectively).

  12. Neutron and Charged-Particle Induced Cross Sections for Radiochemistry in the Region of Samarium, Europium, and Gadolinium

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, R D; Kelley, K; Dietrich, F S; Bauer, R; Mustafa, M

    2004-11-30

    We have developed a set of modeled nuclear reaction cross sections for use in radiochemical diagnostics. Systematics for the input parameters required by the Hauser-Feshbach statistical model were developed and used to calculate neutron and proton induced nuclear reaction cross sections in the mass region of samarium, europium and gadolinium (62 {le} Z {le} 64, 82 {le} N {le} 96).

  13. Colloidal europium nanoparticles via a solvated metal atom dispersion approach and their surface enhanced Raman scattering studies.

    Science.gov (United States)

    Urumese, Ancila; Jenjeti, Ramesh Naidu; Sampath, S; Jagirdar, Balaji R

    2016-08-15

    Chemistry of lanthanide metals in their zerovalent state at the nanoscale remains unexplored due to the high chemical reactivity and difficulty in synthesizing nanoparticles by conventional reduction methods. In the present study, europium(0) nanoparticles, the most reactive of all the rare earth metals have been synthesized by solvated metal atom dispersion (SMAD) method using hexadecyl amine as the capping agent. The as-prepared europium nanoparticles show surface Plasmon resonance (SPR) band in the visible region of the electromagnetic spectrum. This lead to the investigation of its surface enhanced Raman scattering (SERS) using visible light excitation source. The SERS activity of europium nanoparticles has been followed using 4-aminothiophenol and biologically important molecules such as hemoglobin and Cyt-c as the analytes. This is the first example of lanthanide metal nanoparticles as SERS substrate which can possibly be extended to other rare-earth metals. Since hemoglobin absorbs in the visible region, the use of visible light excitation source leads to surface enhanced resonance Raman spectroscopy (SERRS). The interaction of biomolecules with Eu(0) has been followed using FT-IR and UV-visible spectroscopy techniques. The results indicate that there is no major irreversible change in the structure of biomolecules upon interaction with europium nanoparticles. Copyright © 2016 Elsevier Inc. All rights reserved.

  14. Rapid screening of oxytetracycline residue in catfish muscle by dispersive liquid-liquid microextraction and europium-sensitized luminescence

    Science.gov (United States)

    Oxytetracycline (OTC) residue in catfish muscle was screened by dispersive liquid-liquid microextraction (DLLME) and europium-sensitized luminescence (ESL). After extraction in EDTA, HCl, and acetonitrile, cleanup was carried out by DLLME, and ESL was measured at microgram = 385 nm and wavelength = ...

  15. Luminescence variations in europium-doped silicon-substituted hydroxyapatite nanobiophosphor via three different methods

    Energy Technology Data Exchange (ETDEWEB)

    Thang, Cao Xuan; Pham, Vuong-Hung, E-mail: vuong.phamhung@hust.edu.vn

    2015-07-15

    Highlights: • Europium doped silicon-substituted hydroxyapatite was synthesized by wet chemical synthesis method. • Morphology of nanoparticles depended on the synthesized method. • Photoluminescence intensity of the sample increases with the increasing of Si substitutions, Eu dopants and thermal annealing. - Abstract: This paper reports the first attempt for the synthesis of europium-doped Si-substituted hydroxyapatite (HA) nanostructure to achieve strong and stable luminescence of nanobiophosphor, particularly, by addition of different Eu dopants, Si substitutions, and application of optimum annealing temperatures of up to 1000 °C. The nanobiophosphor was synthesized by the coprecipitation, microwave, and hydrothermal methods. The nanoparticles demonstrated a nanowire to a spindle-like morphology, which was dependent on the method of synthesis. The photoluminescence (PL) intensity of the sample increases with the increase in Si substitutions and Eu dopants. The luminescent nanoparticles also showed the typical luminescence of Eu{sup 3+} centered at 610 nm, which was more efficient for the annealed Eu-doped Si-HA nanoparticles than for the as-synthesized nanoparticles. Among the different synthesis methods, the hydrothermal method reveals the best light emission represented by high PL intensity and narrow PL spectra. These results suggest the potential application of Eu-doped Si-HA in stable and biocompatible nanophosphors for light emission and nanomedicine.

  16. Resonance ionization spectroscopy of Europium The first application of the PISA at ISOLDE-RILIS

    CERN Document Server

    AUTHOR|(CDS)2099873; Marsh, Bruce Alan

    The following work has been carried out at the radioactive ion beam facility ISOLDE at CERN. A compact atomic beam unit named PISA (Photo Ionization Spectroscopy Apparatus) has been implemented as a recent addition to the laboratory of the Resonance Ionization Laser Ion Source (RILIS). The scope of this thesis work was to demonstrate different applications of the PISA, using the existing and highly developed laser setup of the RILIS installation. In a demonstration of the suitability of PISA for ionization scheme development, a new ionization scheme for Europium has been developed. This resulted in the observation of several new autoionizing states and Rydberg series. Through the analysis of the observed Rydberg resonances a refined value of $45734.33(3)(3)$ cm$^{-1}$ for the ionization potential of the europium atom has been determined. In addition this thesis reports on the feasibility of the use of the PISA as a RILIS performance monitoring device during laser ion source operations. Finally the present wor...

  17. Structural and electrical properties of the europium-doped indium zinc oxide thin film transistors

    Energy Technology Data Exchange (ETDEWEB)

    Ting, Chu-Chi, E-mail: ccting@ccu.edu.tw [Graduate Institute of Opto-Mechatronics Engineering, National Chung Cheng University, 168 University Rd., Min-Hsiung, Chia-Yi, Taiwan, ROC (China); Advanced Institute for Manufacturing with High-Tech Innovations, National Chung Cheng University, 168 University Rd., Min-Hsiung, Chia-Yi, Taiwan, ROC (China); Li, Wei-Yang; Wang, Ching-Hua; Yong, Hua-En [Graduate Institute of Opto-Mechatronics Engineering, National Chung Cheng University, 168 University Rd., Min-Hsiung, Chia-Yi, Taiwan, ROC (China)

    2014-07-01

    The EuInZnO (EIZO) thin film transistor (TFT) devices were fabricated by the sol–gel spin-coating technique. The EIZO TFT operates in the n-channel depletion mode and exhibits a well-defined pinch-off and saturation region. Because europium ion possesses lower electronegativity (1.2) and standard electrode potential (− 1.991 V), it can act as the carrier suppressor to reduce the carrier concentrations of the IZO (In:Zn = 1:1) thin film. Eu{sup 3+} (13 mol%)-doped IZO TFT possesses the optimum performance, and its field-effect mobility in the saturated regime, threshold voltage, on–off ratio, and S-factor are 1.23 cm{sup 2}/Vs, 3.28 V, 1.07 × 10{sup 6}, and 2.28 V/decade, respectively. - Highlights: • Europium ions can act as the carrier suppressor in the InZnO system. • The EuInZnO forms an n-channel material for the thin film transistor (TFT) device. • The optimum performance of the EuInZnO TFT is the sample with 13 mol% Eu{sup 3+} doping.

  18. Europium phosphomolybdate and osmium metallopolymer multi-functional LbL films: redox and electrocatalytic properties.

    Science.gov (United States)

    Fernandes, Diana M; Vos, Johannes G; Freire, Cristina

    2014-04-15

    Hybrid multilayer films composed by osmium metallopolymer [Os(bpy)2(PVP)10Cl]Cl (Os-poly) and europium phosphomolybdate, K₁₁[Eu(III)(PMo₁₁O₃₉)₂] (Eu(PMo11)2), were prepared using the electrostatic layer-by-layer (LbL) self-assembly method. The film build-up, monitored by electronic spectroscopy, showed a regular stepwise growth indicating a strong interaction between layers. The XPS measurements corroborated the successful fabrication of the hybrid films with the Os-poly/Eu(PMo11)2 composition. SEM images revealed a completely covered surface with a highly roughened texture. Electrochemical characterisation of films by cyclic voltammetry revealed three Mo-based reduction processes (Mo(VI)→Mo(V)) in the potential range between -0.4 and 0.1 V and one Os reduction process (Os(III)→Os(II)) at ≈0.270 V. The cyclic voltammograms of two electroactive probes, [Fe(CN)₆](3-/4-) and [Ru(NH₃)₆](3+/2+) on {Os-poly/Eu(PMo11)2}n modified electrodes revealed redox mediation between film and the probes. Furthermore, the {Os-poly/Eu(PMo11)2}n multilayer films also showed excellent Mo-based electrocatalytic activity towards reduction of nitrite and iodate, confirming the multi-functional properties of the hybrid europium phosphomolybdate - osmium metallopolymer LbL films. Copyright © 2014 Elsevier Inc. All rights reserved.

  19. Theoretical spectroscopic study of the conjugate microcystin-LR-europium cryptate

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Julio G.; Dutra, Jose Diogo L.; Costa Junior, Nivan B. da; Freire, Ricardo O., E-mail: rfreire@ufs.br [Universidade Federal de Sergipe (UFS), Sao Cristovao, SE (Brazil). Departamento de Quimica; Alves Junior, Severino; Sa, Gilberto F. de [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Departamento de Quimica Fundamental

    2013-02-15

    In this work, theoretical tools were used to study spectroscopic properties of the conjugate microcystin-LR-europium cryptate. The Sparkle/AM1 model was applied to predict the geometry of the system and the INDO/S-CIS model was used to calculate the excited state energies. Based on the Judd-Ofelt theory, the intensity parameters were predicted and a theoretical model based on the theory of the 4f-4f transitions was applied to calculate energy transfer and backtransfer rates, radiative and non-radiative decay rates, quantum efficiency and quantum yield. A detailed study of the luminescent properties of the conjugate Microcystin-LR-europium cryptate was carried out. The results show that the theoretical quantum yield of luminescence of 23% is in good agreement with the experimental value published. This fact suggests that this theoretical protocol can be used to design new systems in order to improve their luminescence properties. The results suggest that this luminescent system may be a good conjugate for using in assay ELISA for detection by luminescence of the Microcystin-LR in water. (author)

  20. pH-controlled delivery of luminescent europium coated nanoparticles into platelets

    Science.gov (United States)

    Davies, Amy; Lewis, David J.; Watson, Stephen P.; Thomas, Steven G.; Pikramenou, Zoe

    2012-01-01

    Water soluble, luminescent gold nanoparticles are delivered into human platelets via a rapid, pH-controlled mechanism using a pH low insertion peptide, pHLIP. The approach introduces cocoating of gold nanoparticles with a europium luminescent complex, EuL and the pHLIP peptide to give pHLIP•EuL•Au. The 13-nm diameter gold nanoparticles act as a scaffold for the attachment of both the luminescent probe and the peptide to target delivery. Their size allows delivery of approximately 640 lanthanide probes per nanoparticle to be internalized in human platelets, which are not susceptible to transfection or microinjection. The internalization of pHLIP•EuL•Au in platelets, which takes just minutes, was studied with a variety of imaging modalities including luminescence, confocal reflection, and transmission electron microscopy. The results show that pHLIP•EuL•Au only enters the platelets in low pH conditions, pH 6.5, mediated by the pHLIP translocation across the membrane, and not at pH 7.4. Luminescence microscopy images of the treated platelets show clearly the red luminescence signal from the europium probe and confocal reflection microscopy confirms the presence of the gold particles. Furthermore, transmission electron microscopy gives a detailed insight of the internalization and spatial localization of the gold nanoparticles in the platelets. Thus, we demonstrate the potential of the design to translocate multimodal nanoparticle probes into cells in a pH dependent manner. PMID:22308346

  1. Analysis of metal surfaces coated with europium-doped titanium dioxide by laser induced breakdown spectroscopy.

    Science.gov (United States)

    Głogocka, Daria; Noculak, Agnieszka; Pucińska, Joanna; Jopek, Wojciech; Podbielska, Halina; Langner, Marek; Przybyło, Magdalena

    2015-01-01

    The surface passivation with titanium sol-gel coatings is a frequently used technique to control the adsorption of selected biological macromolecules and to reduce the exposure of the bulk material to biological matter. Due to the increasing number of new coating-preparation methods and new gel compositions with various types of additives, the quality and homogeneity determination of the surface covering is a critical factor affecting performance of any implanted material. While coating thickness is easy to determine, the homogeneity of the surface distribution of coating materials requires more elaborate methodologies. In the paper, the laser induced breakdown spectroscopy (LIBS) based method, capable to quantitate the homogeneity and uniformity of the europium in titanium dioxide sol-gel coatings on stainless steel surfaces prepared with two different procedures: spin-coating and dip-coating, is presented. The emission intensity of titanium has been used to determine the coating thickness whereas the relative values of europium and titanium emission intensities provide data on the coating homogeneity. The obtained results show that the spin-coating technique provides better surface coverage with titanium dioxide. However, when the surface coating compositions were compared the dip-coating technique was more reliable.

  2. Europium(III) Macrocyclic Complexes with Alcohol Pendant Groups as Chemical Exchange Saturation Transfer Agents

    Science.gov (United States)

    Woods, Mark; Woessner, Donald E.; Zhao, Piyu; Pasha, Azhar; Yang, Meng-Yin; Huang, Ching-Hui; Vasalitiy, Olga; Morrow, Janet R.; Sherry, A. Dean

    2009-01-01

    Paramagnetic lanthanide(III) complexes that contain hyperfine-shifted exchangeable protons offer considerable advantages over diamagnetic molecules as chemical exchange saturation transfer (CEST) agents for MRI. As part of a program to investigate avenues to improve the sensitivity of such agents, the CEST characteristics of europium(III) macrocyclic complexes having appended hydroxyethyl groups were investigated. The CEST spectrum of the asymmetrical complex, EuCNPHC3+, shows five distinct peaks for each magnetically nonequivalent exchangeable proton in the molecule. The CEST spectra of this complex were fitted to NMR Bloch theory to yield exchange rates between each of six exchanging proton pools (five on the agent plus bulk water). Exchange between the Eu3+-bound hydroxyl protons and bulk water protons was slow in dry acetonitrile but accelerated incrementally upon stepwise addition of water. In pure water, exchange was too fast to observe a CEST effect. The utility of this class of europium(III) complex for CEST imaging applications is ultimately limited by the small chemical shifts induced by the hydroxyl-appended ligands of this type and the resulting small Δω values for the exchangeable hydroxyl protons. PMID:16881645

  3. Red light emission from europium doped zinc sodium bismuth borate glasses

    Science.gov (United States)

    Hegde, Vinod; Viswanath, C. S. Dwaraka; Upadhyaya, Vyasa; Mahato, K. K.; Kamath, Sudha D.

    2017-12-01

    Zinc sodium bismuth borate (ZNBB) glasses doped with different concentrations of europium were prepared by conventional melt quenching method and characterized through the measurements of density, refractive index, X-ray diffraction (XRD), Fourier Transform Infrared (FTIR) spectra, optical absorption, luminescence and radiative lifetimes. FTIR spectra showed seven characteristic peaks of bismuth and borate functional groups in the range of 400-1600 cm-1. The optical band gap and bonding parameters have been calculated from absorption spectra. Photoluminescence spectra recorded in the visible region with 394 nm excitation are used to calculate the Judd-Ofelt (JO) intensity parameters (Ω2 and Ω4). The JO intensity parameters have been used to calculate the radiative parameters such as branching ratio (β), stimulated emission cross-section (σse), transition probability (A) for the fluorescent level of 5D0→7F2. Decay rates through single exponential are used to calculate the lifetime (τm) of the meta-stable state 5D0 of (Eu3+ ion) these glasses. The radiative parameters measured for all these glasses show 0.7 mol% europium doped zinc sodium bismuth borate glass 5D0→7F2 transition has the potential for red laser applications. The quality of the colour emitted by the present glasses are estimated quantitatively by CIE chromaticity coordinates, which confirms the suitability of these glasses as a red emitting material for field emission technologies and LEDs.

  4. Samarium-153 EDTMP for metastatic bone pain palliation: the impact of europium impurities.

    Science.gov (United States)

    Kalef-Ezra, J A; Valakis, S T; Pallada, S

    2015-02-01

    To evaluate the impact on the radiation protection policies of the radiocontaminants in Samarium-153 ethylenediamine tetramethylene phosphonate ((153)Sm-EDTMP). The internal contamination of patients treated with (153)Sm-EDMTP for palliation of painful disseminated multiple bone metastases due to long-lived impurities was assessed by direct measurements. These measurements were coupled with dose-rate measurements close to their bodies and spectroscopic analysis of the residual activity in post-treatment radiopharmaceutical vials. Whole-body counting carried out in six patients showed a 30-81-kBq europium -152 plus europium-154 contamination. The 0.85 mean (152)Eu- to -(154)Eu activity ratio obtained by direct counting was similar to that assessed by analysis of post-treatment residual activities in twelve radiopharmaceutical vials following radiopharmaceutical injection. The long-lived radiocontaminants in the patient's bodies and the treatment wastes require modifications of the applicable radiation protection policies. Copyright © 2014 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

  5. Induced Europium Circularly Polarized Luminescence Monitors Reversible Drug Binding to Native α1 -Acid Glycoprotein.

    Science.gov (United States)

    Jennings, Laura; Waters, Ryan S; Pal, Robert; Parker, David

    2017-02-03

    Alpha-1-acid glycoprotein (α1 -AGP) is an important blood plasma glycoprotein. Following an acute-phase reaction such as stress, inflammation, burn, or infection, the bloodstream concentration of α1 -AGP can increase up to 400 % of its normal concentration. A wide range of drugs is known to bind α1 -AGP. Increased binding of pharmacologically active compounds to α1 -AGP moderates their clinical effect by decreasing the amount of unbound drug in the bloodstream. This has important clinical ramifications for such applications as the duration of anesthesia and in determining dosage for drug therapy. In this study, the competitive binding to α1 -AGP of a dynamically racemic europium(III) complex with seven pharmacologically active drugs absorbing in the range λ 250-290 nm was monitored by following changes in europium total emission and in induced circularly polarized luminescence (CPL). Binding affinities corresponding to Kd values in the range 0.5-100 μm were measured, in good agreement with published data. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Europium-doped amorphous calcium phosphate porous nanospheres: preparation and application as luminescent drug carriers

    Directory of Open Access Journals (Sweden)

    Zhang Kui-Hua

    2011-01-01

    Full Text Available Abstract Calcium phosphate is the most important inorganic constituent of biological tissues, and synthetic calcium phosphate has been widely used as biomaterials. In this study, a facile method has been developed for the fabrication of amorphous calcium phosphate (ACP/polylactide-block-monomethoxy(polyethyleneglycol hybrid nanoparticles and ACP porous nanospheres. Europium-doping is performed to enable photoluminescence (PL function of ACP porous nanospheres. A high specific surface area of the europium-doped ACP (Eu3+:ACP porous nanospheres is achieved (126.7 m2/g. PL properties of Eu3+:ACP porous nanospheres are investigated, and the most intense peak at 612 nm is observed at 5 mol% Eu3+ doping. In vitro cytotoxicity experiments indicate that the as-prepared Eu3+:ACP porous nanospheres are biocompatible. In vitro drug release experiments indicate that the ibuprofen-loaded Eu3+:ACP porous nanospheres show a slow and sustained drug release in simulated body fluid. We have found that the cumulative amount of released drug has a linear relationship with the natural logarithm of release time (ln(t. The Eu3+:ACP porous nanospheres are bioactive, and can transform to hydroxyapatite during drug release. The PL properties of drug-loaded nanocarriers before and after drug release are also investigated.

  7. "Rigid" Luminescent Soft Materials: Europium-Containing Lyotropic Liquid Crystals Based on Polyoxyethylene Phytosterols and Ionic Liquids.

    Science.gov (United States)

    Yi, Sijing; Wang, Jiao; Feng, Zhenyu; Chen, Xiao

    2017-10-05

    Soft materials of europium β-diketonate complexes constructed in lyotropic liquid crystals (LLCs) mediated by ionic liquids (ILs) are impressive for their excellent luminescence performance and stability. For the aim to further improve their mechanical processability and luminescent tunablility, the polyoxyethylene phytosterols (BPS-n) were introduced here as structure directing agents to prepare relatively "rigid" lamellar luminescent LLCs in 1-butyl-3-methyl-imidazolium hexafluorophosphate by doping europium β-diketonate complexes with different imidazolium counterions. As a result of the solvophobic sterol ring structure of BPS-n, the more effective isolation and confinement effects of europium complexes could be achieved. The longest fluorescence lifetime and the highest quantum efficiency reported so far for europium containing lyotropic organized soft materials were thus obtained. Changing the molecular structures of BPS-n with different oxyethylene chains or doped complexes with imidazolium counterions of different alkyl chain lengths, the spacings of lamellar LLC matrixes and position of dispersed complexes became tunable. The measured luminescent and rheological properties for such composite LLCs showed a dependence on the rigidity and isolation capability afforded by sterol molecules. It was also found that the increase of counterion alkyl chain length would weaken the LLC matrix's confinement and isolation effects and therefore exhibit the deteriorated luminescence performance. The enhanced luminescence efficiency and stability of doped BPS-n LLCs reflected the excellent segregation of europium complexes from each other and therefore the reduced self-quenching process. The obtained results here present the designability of LLC matrixes and their great potential to promote achieving the luminescence tunability of soft materials.

  8. Preparation and photoluminescence of some europium (III) ternary complexes with β-diketone and nitrogen heterocyclic ligands

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Dunjia, E-mail: dunjiawang@163.com; Pi, Yan; Zheng, Chunyang; Fan, Ling; Hu, Yanjun; Wei, Xianhong

    2013-10-15

    Highlights: •Preparation of europium (III) ternary complexes with β-diketone and nitrogen heterocyclic ligands. •Photoluminescence behavior of europium (III) ternary complexes. •Analysis of the Judd–Ofelt intensity parameters (Ω{sub t}), the lifetime (τ) and the luminescent quantum yield (η). -- Abstract: Preparation and photoluminescence behavior of four new europium (III) ternary complexes with β-diketones (1-(6-methoxy-naphthalen-2-yl)-3-phenyl-propane-1,3-dione (MNPPD) and 1-(4-tert-butyl-phenyl)-3-(6-methoxy-naphthalen-2-yl)-propane-1,3-dione (BPMPD)) and 2,2-dipyridine (Bipy) or 1,10-phenanthroline (Phen) were reported, in the solid state. Complexes Eu(MPPD){sub 3}·Bipy, Eu(BMPD){sub 3}·Bipy, Eu(MPPD){sub 3}·Phen and Eu(BMPD){sub 3}·Phen were characterized by elemental analysis, FT-IR, {sup 1}H NMR, UV–vis absorption. The emission spectra show narrow emission bands that arise from the {sup 5}D{sub 0} → {sup 7}F{sub J} (J = 0–4) transitions of the europium ion. Based on the emission spectra and luminescence decay curves in solid state, the intensity parameters (Ω{sub t}), lifetime (τ) and emission quantum efficiency (η) were determined. The Ω{sub 2} values indicate that the Eu(III) ion in these complexes is in a highly polarizable chemical environment. Complexes Eu(MPPD){sub 3}·Bipy and Eu(MPPD){sub 3}·Phen showed a longer lifetime (τ) and a higher luminescence quantum efficiency (η), which indicated that the energy transfer to the europium ion from MNPPD ligand is more efficient than that from BPMPD ligand.

  9. Luminescent method of determination of composition of europium and terbium complexes in solution by change of intensity ratio of luminescence bands

    Energy Technology Data Exchange (ETDEWEB)

    Bel' tyukova, S.V.; Nazarenko, N.A.; Poluehktov, N.S.

    1982-03-01

    The complexes of europium and terbium with phenanthroline, ethylenediaminetetraacetate, nitrilotriacetate, some acids-phenol derivatives and ..beta..-diketones series have been used as an example to demonstrate that the value of the ratio of intensities on the two bands of europium(terbium) luminescence spectra - the one corresponding to the hypersensitive'' transition and the other, to the magnetic dipole one - can be used for determination of the complexes composition in solutions.

  10. Syntheses and electroluminescent properties of two europium ternary complexes Eu(DBM){sub 3}(PBO) and Eu(DBM){sub 3}(PBT)

    Energy Technology Data Exchange (ETDEWEB)

    Guan Min [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Gao Lihua [Department of Chemistry, Beijing Normal University, Beijing 100875 (China); Wang Shanshan [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Huang Chunhui [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China)], E-mail: chhuang@pku.edu.cn; Wang Kezhi [Department of Chemistry, Beijing Normal University, Beijing 100875 (China)

    2007-12-15

    Two europium complexes, Eu(DBM){sub 3}(PBO) and Eu(DBM){sub 3}(PBT) (DBM=dibenzoylmethanato, PBO=2-(2-pyridyl)benzoxazole, PBT=2-(2-pyridyl)benzothiazole), were prepared and used as emitting materials in organic electroluminescent (EL) devices. The devices with the structures ITO/TPD/Eu(DBM){sub 3}(PBO) (or Eu(DBM){sub 3}(PBT)/BCP/Alq{sub 3}/Mg:Ag/Ag emit red light originating from the europium complexes.

  11. Stability constants of europium complexes with a nitrogen heterocycle substituted methane-1,1-diphosphonic acid

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, M.P.; Rickert, P.G.; Schmidt, M.A.; Nash, K.L.

    1996-06-01

    Even in moderately acidic solutions ([H{sup +}] > 0.01 M), N-piperidinomethane-1,1-diphosphonic acid (H{sub 4}PMDPA) is a strong complexant of trivalent lanthanide ions that shows enhanced complex solubility over previously studied 1,1-diphosphonic acids. The protonation constants of PMDPA in 2.0 M H/NaClO{sub 4} were determined by potentiometric and NMR titrations, and the stability constants for formation of complexes with Eu{sup 3+} were determined by solvent extraction. Difference in protonation equilibria induced by addition of the nitrogen heterocycle results in an increase in the complexation strength of PMDPA. In solutions containing 0.1 M H{sup +} and ligand concentrations greater than 0.02 M, PMDPA is the most effective 1,1-diphosphonic acid for europium complexation studied thus far.

  12. Sorption of Europium in zirconium silicate; Sorcion de Europio en silicato de circonio

    Energy Technology Data Exchange (ETDEWEB)

    Garcia R, G. [ININ, Carretera Mexico-Toluca Km. 36.5, 52045 Estado de Mexico (Mexico)

    2004-07-01

    Some minerals have the property of sipping radioactive metals in solution, that it takes advantage to manufacture contention barriers that are placed in the repositories of nuclear wastes. The more recent investigations are focused in the development of new technologies guided to the sorption of alpha emissors on minerals which avoid their dispersion in the environment. In an effort to contribute to the understanding of this type of properties, some studies of sorption of Europium III are presented like homologous of the americium, on the surface of zirconium silicate (ZrSiO{sub 4}). In this work the results of sorption experiences are presented as well as the interpretation of the phenomena of the formation of species in the surface of the zirconium silicate. (Author)

  13. First principles description of the insulator-metal transition in europium monoxide

    KAUST Repository

    Wang, Hao

    2012-02-01

    Europium monoxide, EuO, is a ferromagnetic insulator. Its electronic structure under pressure and doping is investigated by means of density functional theory. We employ spin polarized electronic structure calculations including onsite electron-electron interaction for the localized Eu 4f and 5d electrons. Our results show that under pressure the ferromagnetism is stable, both for hydrostatic and uniaxial pressure, while the compound undergoes an insulator-metal transition. The insulator-metal transition in O deficient and Gd doped EuO is reproduced for an impurity concentration of 6.25%. A 10 monolayer thick EuO(1 0 0) thin film is predicted to be an insulator with a narrow band gap of 0.08 eV. © 2011 Elsevier B.V. All rights reserved.

  14. Development of europium doped BaSO4 TL OSL dual phosphor for radiation dosimetry applications

    Science.gov (United States)

    Patle, Anita; Patil, R. R.; Kulkarni, M. S.; Bhatt, B. C.; Moharil, S. V.

    2015-08-01

    This paper presents the results on the preparation and characterization of Europium-doped Barium sulfate (BaSO4: Eu) TL /OSL dual phosphor. The OSL sensitivity was found to be 11% of the commercially available Al2O3: C, using area integration method. The sample also shows good TL sensitivity and the dosimetric peak appears around 190°C with a shoulder at 282°C. After OSL readout, No change in the TL glow curve is observed. Since the observed TL peaks are not responsible for the observed OSL, good OSL as well as TL sensitivity and low fading will make this phosphor suitable for applications in radiation dosimetry using OSL as well as TL.

  15. Chemiluminescence determination of tetracyclines using Fenton system in the presence europium(III) ions

    Energy Technology Data Exchange (ETDEWEB)

    Kaczmarek, Malgorzata [Department of Rare Earths, Faculty of Chemistry, Adam Mickiewicz University, Grunwaldzka 6, 60 - 780 Poznan (Poland); Lis, Stefan, E-mail: blis@amu.edu.pl [Department of Rare Earths, Faculty of Chemistry, Adam Mickiewicz University, Grunwaldzka 6, 60 - 780 Poznan (Poland)

    2009-04-20

    A new simple chemiluminescent method for the determination of chlortetracycline (Chlor-TC), oxytetracycline (Oxy-TC) and doxycycline (Doxy-TC) is described. This method is based on the europium(III) emission as a result of the energy transfer process from the excited product of the tetracyclines oxidation to the uncomplexed Eu(III). Under the optimum conditions, calibration graphs were obtained for 4 x 10{sup -7} to 2 x 10{sup -5} mol L{sup -1} of Chlor-TC; 2 x 10{sup -7} to 2 x 10{sup -5} mol L{sup -1} of Oxy-TC and 1 x 10{sup -7} to 3 x 10{sup -5} mol L{sup -1} of Doxy-TC. The method was successfully applied to the determination of these drugs in pharmaceutical and veterinary formulation and honey.

  16. Europium-doped aluminum oxide phosphors as indicators for frontal polymerization dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Carranza, Arturo; Gewin, Mariah; Pojman, John A., E-mail: japojman@lsu.edu [Department of Chemistry, Louisiana State University, Baton Rouge, Louisiana 70803-1804 (United States)

    2014-06-15

    In this study, we present an inexpensive and practical method that allows the monitoring and visualization of front polymerization, propagation, and dynamics. Commercially available europium-doped aluminum oxide powders were combined with video imaging to visualize free-radical propagating polymer fronts. In order to demonstrate the applicability of this method, frontal copolymerization reactions of propoxylated glycerin triacrylate (EB53), pentaerythritol triacrylate (PETA), and pentaerythritol tetra-acrylate (PETEA) with 1,1-Bis(tert-butylperoxy)-3,3,5-trimethylcyclohexane (Luperox 231®) as an initiator were studied and compared to the results obtained by IR imaging. Systems exhibiting higher filler loading, higher EB53 content, and less acrylated monomers showed a marked decrease in front velocity, while those with more acrylated monomers and higher crosslinking density showed a marked increase in front velocity. Finally, in order to show the potential of the imaging technique, we studied fronts propagating in planar and spherical geometries.

  17. Europium-doped aluminum oxide phosphors as indicators for frontal polymerization dynamics.

    Science.gov (United States)

    Carranza, Arturo; Gewin, Mariah; Pojman, John A

    2014-06-01

    In this study, we present an inexpensive and practical method that allows the monitoring and visualization of front polymerization, propagation, and dynamics. Commercially available europium-doped aluminum oxide powders were combined with video imaging to visualize free-radical propagating polymer fronts. In order to demonstrate the applicability of this method, frontal copolymerization reactions of propoxylated glycerin triacrylate (EB53), pentaerythritol triacrylate (PETA), and pentaerythritol tetra-acrylate (PETEA) with 1,1-Bis(tert-butylperoxy)-3,3,5-trimethylcyclohexane (Luperox 231®) as an initiator were studied and compared to the results obtained by IR imaging. Systems exhibiting higher filler loading, higher EB53 content, and less acrylated monomers showed a marked decrease in front velocity, while those with more acrylated monomers and higher crosslinking density showed a marked increase in front velocity. Finally, in order to show the potential of the imaging technique, we studied fronts propagating in planar and spherical geometries.

  18. Electrochemiluminescence Study of Europium (III Complex with Coumarin3-Carboxylic Acid

    Directory of Open Access Journals (Sweden)

    Stefan Lis

    2008-01-01

    Full Text Available The europium (III complex of coumarin-3-carboxylic acid (C3CA has been prepared and characterized on the basis of elemental analysis, IR, and emission (photoluminescence and electrochemiluminescence spectroscopy. The synthesised complex having a formula Eu(C3CA2(NO3(H2O2 was photophysically characterized in solution and in the solid state. Electrochemiluminescence, ECL, of the system containing the Eu(III/C3CA complex was studied using an oxide-covered aluminium electrode. The goal of these studies was to show the possibility of the use of electrochemical excitation of the Eu(III ion in aqueous solution for emission generation. The generated ECL emission was very weak, and therefore its measurements and spectral analysis were carried out with the use of cut-off filters method. The studies proved a predominate role of the ligand-to-metal energy transfer (LMET in the generated ECL.

  19. Europium incorporated in silica matrix obtained by sol-gel: luminescent materials

    Directory of Open Access Journals (Sweden)

    Nassar Eduardo José

    2003-01-01

    Full Text Available In this work we report some aspects of the chemistry involved in the preparation of modified silicon oxide by the sol-gel process. Europium III compounds were used as luminescent probe. An organic-inorganic hybrid was obtained by hydrolysis of tetraethylorthosilicate (TEOS and 3-aminopropyltriethoxysilane (APTS. The Eu III compounds were added in different ways. In the first, silica was prepared in the presence of Eu III, and in the second, Eu III was added on the silica surface. These materials were studied by luminescence, infrared spectroscopy and termogravimetric analysis. The results obtained for the hybrid material show different behavior for Eu III emission, which could be excited by the antenna effect and the influence of the surrounding in the luminescence quenching. The thermogravimetric data present different mass loss in samples to range temperature 50 - 150 °C. Thermogravimetric and infrared spectra showed that inorganic polymers incorporated the organic part.

  20. Europium as an inhibitor of Amyloid-β(1-42) induced membrane permeation.

    Science.gov (United States)

    Williams, Thomas L; Urbanc, Brigita; Marshall, Karen E; Vadukul, Devkee M; Jenkins, A Toby A; Serpell, Louise C

    2015-10-24

    Soluble Amyloid-beta (Aβ) oligomers are a source of cytotoxicity in Alzheimer's disease (AD). The toxicity of Aβ oligomers may arise from their ability to interact with and disrupt cellular membranes mediated by GM1 ganglioside receptors within these membranes. Therefore, inhibition of Aβ-membrane interactions could provide a means of preventing the toxicity associated with Aβ. Here, using Surface Plasmon field-enhanced Fluorescence Spectroscopy, we determine that the lanthanide, Europium III chloride (Eu(3+)), strongly binds to GM1 ganglioside-containing membranes and prevents the interaction with Aβ42 leading to a loss of the peptides ability to cause membrane permeation. Here we discuss the molecular mechanism by which Eu(3+) inhibits Aβ42-membrane interactions and this may lead to protection of membrane integrity against Aβ42 induced toxicity. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

  1. Radiation effects on beta /10.6/ of pure and europium doped KCl

    Science.gov (United States)

    Grimes, H. H.; Maisel, J. E.; Hartford, R. H.

    1975-01-01

    Changes in the optical absorption coefficient as the result of X-ray and electron bombardment of pure monocrystalline and polycrystalline KCl and of divalent europium doped polycrystalline KCl were determined. A constant heat flow calorimetric method was used to measure the optical absorption coefficients. Both 300 kV X-ray irradiation and 2 MeV electron irradiation produced increases in the optical absorption coefficient at room temperature. X-ray irradiation produced more significant changes in pure monocrystalline KCl than equivalent amounts of electron irradiation. Electron irradiation of pure and Eu-doped polycrystalline KCl produced increases in the absorption by as much as a factor of 20 over untreated material. Bleaching of the electron-irradiated doped KCl with 649 millimicron light produced a further increase.

  2. Excitation functions for the formation of longer lived isotopes by deuteron irradiation of Europium

    Energy Technology Data Exchange (ETDEWEB)

    Takács, S., E-mail: stakacs@atomki.hu [Institute for Nuclear Research, Hungarian Academy of Sciences, 4026 Debrecen (Hungary); Tárkányi, F. [Institute for Nuclear Research, Hungarian Academy of Sciences, 4026 Debrecen (Hungary); Hermanne, A.; Adam-Rebeles, R. [Cyclotron Laboratory, Vrije Universiteit Brussel, Brussels 1090 (Belgium); Takács, M.P. [Institute for Nuclear Research, Hungarian Academy of Sciences, 4026 Debrecen (Hungary); Institute of Physics, University of Debrecen, 4026 Debrecen (Hungary)

    2013-09-01

    Excitation functions for nuclear reactions induced on natural europium targets by energetic deuterons were studied up to 50 MeV. A standard stacked foil technique was used for irradiation and high resolution gamma spectrometry was applied for activity assessment. Direct or cumulative cross sections for reaction products with half-life longer than 2 h were determined. Reactions leading to the formation of the radionuclides {sup 147,149,151,153}Gd, {sup 147,148,149,150m,150g,152m,152g,154g}Eu, {sup 153}Sm and {sup 150}Pm were studied. In most cases no earlier data were available in the literature. The new experimental results were compared with values tabulated in the on-line TENDL2011 library.

  3. Quadrupole splitting and Eu partial lattice dynamics in europium orthophosphate EuPO {sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Klobes, B., E-mail: b.klobes@fz-juelich.de [JARA-FIT - Forschungszentrum Jülich GmbH, Jülich Centre for Neutron Science JCNS and Peter Grünberg Institute PGI (Germany); Arinicheva, Y., E-mail: y.arinicheva@fz-juelich.de; Neumeier, S., E-mail: s.neumeier@fz-juelich.de [Forschungszentrum Jülich GmbH, Institute of Energy and Climate Research (IEK-6) Nuclear Waste Management and Reactor Safety (Germany); Simon, R. E., E-mail: r.simon@fz-juelich.de; Jafari, A., E-mail: a.jafari@fz-juelich.de [JARA-FIT - Forschungszentrum Jülich GmbH, Jülich Centre for Neutron Science JCNS and Peter Grünberg Institute PGI (Germany); Bosbach, D., E-mail: d.bosbach@fz-juelich.de [Forschungszentrum Jülich GmbH, Institute of Energy and Climate Research (IEK-6) Nuclear Waste Management and Reactor Safety (Germany); Hermann, R. P., E-mail: hermannrp@ornl.gov [JARA-FIT - Forschungszentrum Jülich GmbH, Jülich Centre for Neutron Science JCNS and Peter Grünberg Institute PGI (Germany)

    2016-12-15

    Hyperfine interactions in europium orthophosphate EuPO{sub 4} were investigated using {sup 151}Eu Mössbauer spectroscopy from 6 to 300 K. The value of the quadrupole splitting and the asymmetry parameter were refined and further substantiated by nuclear forward scattering data obtained at room temperature. The temperature dependence of the relative absorption was modeled with an Eu specific Debye temperature of 221(1) K. Eu partial lattice dynamics were probed by means of nuclear inelastic scattering and the mean force constant, the Lamb-Mössbauer factor, the internal energy, the vibrational entropy, the average phonon group velocity were calculated using the extracted density of phonon states. In general, Eu specific vibrations are characterized by rather small phonon energies and contribute strongly to the total entropy of the system. Although there is no classical Debye like behavior at low vibrational energies, the average phonon group velocity can be reasonably approximated using a linear fit.

  4. Photoluminescent polymer electrolyte based on agar and containing europium picrate for electrochemical devices

    Energy Technology Data Exchange (ETDEWEB)

    Lima, E. [Centro de Quimica, Universidade do Minho, Gualtar, 4710-057 Braga (Portugal); Raphael, E.; Sentanin, F. [IQSC, Universidade de Sao Paulo, 13566-590 Sao Carlos, SP (Brazil); Rodrigues, L.C. [Centro de Quimica, Universidade do Minho, Gualtar, 4710-057 Braga (Portugal); Ferreira, R.A.S.; Carlos, L.D. [Departamento de Fisica, CICECO, Universidade de Aveiro, 3810-193 Aveiro (Portugal); Silva, M.M., E-mail: nini@quimica.uminho.pt [Centro de Quimica, Universidade do Minho, Gualtar, 4710-057 Braga (Portugal); Pawlicka, A. [IQSC, Universidade de Sao Paulo, 13566-590 Sao Carlos, SP (Brazil)

    2012-04-15

    Highlights: Black-Right-Pointing-Pointer We prepared ionic conducting membranes for the specific requirements of the device. Black-Right-Pointing-Pointer Luminescent reporter groups, with many applications in biotechnology. Black-Right-Pointing-Pointer Thermal and electrochemical stability of electrolytes is adequate for application. - Abstract: Dispersion of photoluminescent rare earth metal complexes in polymer matrices is of great interest due to the possibility of avoiding the saturation of the photoluminescent signal. The possibility of using a natural ionic conducting polymer matrix was investigated in this study. Samples of agar-based electrolytes containing europium picrate were prepared and characterized by physical and chemical analyses. The FTIR spectra indicated strong interaction of agar O-H and 3,6-anhydro-galactose C-O groups with glycerol and europium picrate. The DSC analyses revealed no glass transition temperature of the samples in the -60 to 250 Degree-Sign C range. From the thermogravimetry (TG), a thermal stability of the samples of up to 180 Degree-Sign C was stated. The membranes were subjected to ionic conductivity measurement, which provided the values of 2.6 Multiplication-Sign 10{sup -6} S/cm for the samples with acetic acid and 1.6 Multiplication-Sign 10{sup -5} S/cm for the samples without acetic acid. Moreover, the temperature-dependent ionic conductivity measurements revealed both Arrhenius and VTF models of the conductivity depending on the sample. Surface visualization through scanning electron microscopy (SEM) demonstrated good uniformity. The samples were also applied in small electrochromic devices and showed good electrochemical stability. The present work confirmed that these materials may perform as satisfactory multifunctional component layers in the field of electrochemical devices.

  5. Spectroscopic investigation on europium doped heavy metal borate glasses for red luminescent application

    Energy Technology Data Exchange (ETDEWEB)

    Hegde, Vinod; Wagh, Akshatha; Kamath, Sudha D. [Manipal University, Department of Physics, Manipal Institute of Technology, Manipal (India); Hegde, Hemanth [Manipal University, Department of Chemistry, Manipal Institute of Technology, Manipal (India); Vishwanath, C.S.D. [Sri Venkateswara University, Department of Physics, Tirupati (India)

    2017-05-15

    The present study explores a new borate family glasses based on 10ZnO-5Na{sub 2}O-10Bi{sub 2}O{sub 3}-(75 - x) B{sub 2}O{sub 3}-xEu{sub 2}O{sub 3} (x = 0, 0.1, 0.5, 1, 1.5, 2, 3 mol%) composition, synthesized by rapid melt quench technique. Prepared glasses were subjected to the density and refractive index measurements and their values were used to calculate other physical properties of the glass matrix as a function of Eu{sup 3+} concentration. XRD confirmed amorphous nature of the glasses. FTIR spectra in the absorption mode were recorded in the 400-4000 cm{sup -1} region to identify different functional groups in the glass matrix. Deconvoluted FTIR spectra showed increase in BO{sub 4} units with rise in europium content which confirmed the 'network strengthener' role of europium ions by creating bridging oxygens (BOs). Optical properties were investigated for their luminescence behavior through various spectroscopic techniques such as UV-Vis-NIR absorption, excitation, emission, decay profiles, and color measurements at room temperature. Lasing properties of the glasses like total radiative life time, branching ratio, emission cross section, and optical gain were obtained from the calculated Judd-Ofelt (Ω{sub 2},Ω{sub 4}) intensity parameters. From the measured values of emission, cross sections, branching ratios, life times, strong photoluminescence features, and CIE chromaticity coordinates, 0.5 mol% of Eu{sup 3+} ions doped ZnNaBiB glasses showed optimum performance and are potential candidate for red light generation at 613 nm. (orig.)

  6. Europium nanoparticle-based high performing immunoassay for the screening of treponemal antibodies.

    Directory of Open Access Journals (Sweden)

    Sheikh M Talha

    Full Text Available Treponema pallidum subspecies pallidum (Tp is the causative agent of syphilis which mainly spreads through sexual contact, blood transfusion and perinatal route. In order to curtail the spread of the infection and to clinically manage the disease, timely, accurate and reliable diagnosis is very important. We have developed an immunoassay for the detection of treponemal antibodies in human serum or plasma samples. In vivo biotinylated and non-biotinylated versions of the recombinant antigen were designed by the fusion of three Tp-specific antigens namely Tp15, Tp17 and Tp47. These fusion antigens were expressed in E. coli and purified using single-step metal affinity chromatography. Biotinylated fusion antigen immobilized on streptavidin coated plate was used to capture the treponemal antibodies and the non-biotinylated antigen coated on europium nanoparticles was used as tracer. Assays with two different incubation times of 10 min and 1 h were developed, and following the incubation the europium fluorescence was measured using time-resolved fluorometry. The developed time-resolved fluorometric (TRF immunoassays were evaluated with in-house and commercial serum/plasma sample panels. For well-established treponemal antibodies positive or negative samples, the sensitivity of TRF immunoassay with 10 min incubation time was 97.4%, and of TRF immunoassay with 1 h incubation time was 98.7%, and the specificities of both the TRF immunoassays were 99.2%. For the samples with discordant results with the reference assays, both the TRF immunoassays showed better specificity than the Enzygnost syphilis enzyme immunoassay as a screening test. The two different incubation times did not have any significant effect on the signal to cutoff (S/Co ratios obtained with the two immunoassays (p=0.06. Our results indicate that the developed immunoassay with a short incubation time of 10 min has the potential to be used in clinical laboratories and in blood

  7. Visible-light-excited and europium-emissive nanoparticles for highly-luminescent bioimaging in vivo.

    Science.gov (United States)

    Wu, Yongquan; Shi, Mei; Zhao, Lingzhi; Feng, Wei; Li, Fuyou; Huang, Chunhui

    2014-07-01

    Europium(III)-based material showing special milliseconds photoluminescence lifetime has been considered as an ideal time-gated luminescence probe for bioimaging, but is still limited in application in luminescent small-animal bioimaging in vivo. Here, a water-soluble, stable, highly-luminescent nanosystem, Ir-Eu-MSN (MSN = mesoporous silica nanoparticles, Ir-Eu = [Ir(dfppy)2(pic-OH)]3Eu·2H2O, dfppy = 2-(2,4-difluorophenyl)pyridine, pic-OH = 3-hydroxy-2-carboxypyridine), was developed by an in situ coordination reaction to form an insoluble dinuclear iridium(III) complex-sensitized-europium(III) emissive complex within mesoporous silica nanoparticles (MSNs) which had high loading efficiency. Compared with the usual approach of physical adsorption, this in-situ reaction strategy provided 20-fold the loading efficiency (43.2%) of the insoluble Ir-Eu complex in MSNs. These nanoparticles in solid state showed bright red luminescence with high quantum yield of 55.2%, and the excitation window extended up to 470 nm. These Ir-Eu-MSN nanoparticles were used for luminescence imaging in living cells under excitation at 458 nm with confocal microscopy, which was confirmed by flow cytometry. Furthermore, the Ir-Eu-MSN nanoparticles were successfully applied into high-contrast luminescent lymphatic imaging in vivo under low power density excitation of 5 mW cm(-2). This synthetic method provides a universal strategy of combining hydrophobic complexes with hydrophilic MSNs for in vivo bioimaging. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Europium Nanoparticle-Based High Performing Immunoassay for the Screening of Treponemal Antibodies

    Science.gov (United States)

    Talha, Sheikh M.; Hytönen, Jukka; Westhorpe, Adam; Kumar, Sushil; Khanna, Navin; Pettersson, Kim

    2013-01-01

    Treponema pallidum subspecies pallidum (Tp) is the causative agent of syphilis which mainly spreads through sexual contact, blood transfusion and perinatal route. In order to curtail the spread of the infection and to clinically manage the disease, timely, accurate and reliable diagnosis is very important. We have developed an immunoassay for the detection of treponemal antibodies in human serum or plasma samples. In vivo biotinylated and non-biotinylated versions of the recombinant antigen were designed by the fusion of three Tp-specific antigens namely Tp15, Tp17 and Tp47. These fusion antigens were expressed in E. coli and purified using single-step metal affinity chromatography. Biotinylated fusion antigen immobilized on streptavidin coated plate was used to capture the treponemal antibodies and the non-biotinylated antigen coated on europium nanoparticles was used as tracer. Assays with two different incubation times of 10 min and 1 h were developed, and following the incubation the europium fluorescence was measured using time-resolved fluorometry. The developed time-resolved fluorometric (TRF) immunoassays were evaluated with in-house and commercial serum/plasma sample panels. For well-established treponemal antibodies positive or negative samples, the sensitivity of TRF immunoassay with 10 min incubation time was 97.4%, and of TRF immunoassay with 1 h incubation time was 98.7%, and the specificities of both the TRF immunoassays were 99.2%. For the samples with discordant results with the reference assays, both the TRF immunoassays showed better specificity than the Enzygnost syphilis enzyme immunoassay as a screening test. The two different incubation times did not have any significant effect on the signal to cutoff (S/Co) ratios obtained with the two immunoassays (p = 0.06). Our results indicate that the developed immunoassay with a short incubation time of 10 min has the potential to be used in clinical laboratories and in blood-bank settings as a

  9. Semiconducting polymer encapsulated mesoporous silica particles with conjugated Europium complexes: toward enhanced luminescence under aqueous conditions.

    Science.gov (United States)

    Zhang, Jixi; Prabhakar, Neeraj; Näreoja, Tuomas; Rosenholm, Jessica M

    2014-01-01

    Immobilization of lanthanide organic complexes in meso-organized hybrid materials for luminescence applications have attracted immense interest due to the possibility of controlled segregation at the nanoscopic level for novel optical properties. Aimed at enhancing the luminescence intensity and stability of the hybrid materials in aqueous media, we developed polyvinylpyrrolidone (PVP) stabilized, semiconducting polymer (poly(9-vinylcarbazole), PVK) encapsulated mesoporous silica hybrid particles grafted with Europium(III) complexes. Monosilylated β-diketonate ligands (1-(2-naphthoyl)-3,3,3-trifluoroacetonate, NTA) were first co-condensed in the mesoporous silica particles as pendent groups for bridging and anchoring the lanthanide complexes, resulting in particles with an mean diameter of ∼ 450 nm and a bimodal pore size distribution centered at 3.5 and 5.3 nm. PVK was encapsulated on the resulted particles by a solvent-induced surface precipitation process, in order to seal the mesopores and protect Europium ions from luminescence quenching by producing a hydrophobic environment. The obtained polymer encapsulated MSN-EuLC@PVK-PVP particles exhibit significantly higher intrinsic quantum yield (Φ(Ln) = 39%) and longer lifetime (τ(obs) = 0.51 ms), as compared with those without polymer encapsulation. Most importantly, a high luminescence stability was realized when MSN-EuLC@PVK-PVP particles were dispersed in various aqueous media, showing no noticeable quenching effect. The beneficial features and positive attributes of both mesoporous silica and semiconducting polymers as lanthanide-complex host were merged in a single hybrid carrier, opening up the possibility of using these hybrid luminescent materials under complex aqueous conditions such as biological/physiological environments.

  10. Surface-imprinted nanofilaments for europium-amplified luminescent detection of fluoroquinolone antibiotics.

    Science.gov (United States)

    Zdunek, Jolanta; Benito-Peña, Elena; Linares, Ana; Falcimaigne-Cordin, Aude; Orellana, Guillermo; Haupt, Karsten; Moreno-Bondi, María C

    2013-07-29

    The development and characterization of novel, molecularly imprinted polymer nanofilament-based optical sensors for the analysis of enrofloxacin, an antibiotic widely used for human and veterinary applications, is reported. The polymers were prepared by nanomolding in porous alumina by using enrofloxacin as the template. The antibiotic was covalently immobilized on to the pore walls of the alumina by using different spacers, and the prepolymerization mixture was cast in the pores and the polymer synthesized anchored onto a glass support through UV polymerization. Various parameters affecting polymer selectivity were evaluated to achieve optimal recognition, namely, the spacer arm length and the binding solvent. The results of morphological characterization, binding kinetics, and selectivity of the optimized polymer material for ENR and its derivatives are reported. For sensing purposes, the nanofilaments were incubated in solutions of the target molecule in acetonitrile/HEPES buffer (100 mM, pH 7.5, 50:50, v/v) for 20 min followed by incubation in a 10 mM solution of europium(III) ions to generate a europium(III)-enrofloxacin complex on the polymer surface. The detection event was based on the luminescence of the rare-earth ion (λexc=340 nm; λem=612 nm) that results from energy transfer from the antibiotic excited state to the metal-ion emitting excited state. The limit of detection of the enrofloxacin antibiotic was found to be 0.58 μM. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Faster Synthesis of Beta-Diketonate Ternary Europium Complexes: Elapsed Times & Reaction Yields.

    Science.gov (United States)

    Lima, Nathalia B D; Silva, Anderson I S; Gerson, P C; Gonçalves, Simone M C; Simas, Alfredo M

    2015-01-01

    β-diketonates are customary bidentate ligands in highly luminescent ternary europium complexes, such as Eu(β-diketonate)3(L)2, where L stands for a nonionic ligand. Usually, the syntheses of these complexes start by adding, to an europium salt such as EuCl3(H2O)6, three equivalents of β-diketonate ligands to form the complexes Eu(β-diketonate)3(H2O)2. The nonionic ligands are subsequently added to form the target complexes Eu(β-diketonate)3(L)2. However, the Eu(β-diketonate)3(H2O)2 intermediates are frequently both difficult and slow to purify by recrystallization, a step which usually takes a long time, varying from days to several weeks, depending on the chosen β-diketonate. In this article, we advance a novel synthetic technique which does not use Eu(β-diketonate)3(H2O)2 as an intermediate. Instead, we start by adding 4 equivalents of a monodentate nonionic ligand L straight to EuCl3(H2O)6 to form a new intermediate: EuCl3(L)4(H2O)n, with n being either 3 or 4. The advantage is that these intermediates can now be easily, quickly, and efficiently purified. The β-diketonates are then carefully added to this intermediate to form the target complexes Eu(β-diketonate)3(L)2. For the cases studied, the 20-day average elapsed time reduced to 10 days for the faster synthesis, together with an improvement in the overall yield from 42% to 69%.

  12. Modified magnetic and optical properties of manganese nanoparticles incorporated europium doped magnesium borotellurite glass

    Energy Technology Data Exchange (ETDEWEB)

    Aziz, Siti Maisarah; Sahar, M.R., E-mail: mrahim057@gmail.com; Ghoshal, S.K.

    2017-02-01

    This paper reports the modified optical and magnetic properties of europium (Eu{sup 3+}) ions doped and Manganese nanoparticles (NPs) embedded Magnesium Borotellurite glass synthesized via melt quenching method. The influence of varying Mn NPs concentrations on the magnetic, absorption and emission properties of such glass samples are determined. Stables, transparent and amorphous glasses are obtained. The observed modification of the electronic polarizability is interpreted in terms of the generation of non-bridging oxygen (NBO) and bridging oxygen (BO) in the amorphous network. TEM images manifested the growth of Mn NPs with average diameter 11±1 nm. High-resolution TEM reveals that the lattice spacing of manganese nanoparticles is 0.308 nm at (112) plane. The emission spectra revealed four prominent peaks centered at 587 nm, 610 nm, 651 nm and 700 nm assigned to the transition from {sup 5}D{sub 0} →{sup 7}F{sub J} (J=1, 2, 3, 4) states of Eu{sup 3+} ion. A significant drop in the luminescence intensity due to the incorporation of Mn NPs is ascribed to the enhanced energy transfer from the Eu{sup 3+} ion to NPs. Prepared glass systems exhibited paramagnetic behavior. - Highlights: • The europium doped magnesium borotellurite glasses embedded Mn NPs prepared using the conventional melt-quenching method. • The TEM result reveals the size of Mn NPs while its planar spacing has been determined by HRTEM. • The luminescence properties of TeO{sub 2}–B{sub 2}O{sub 3}–MgO–Eu{sub 2}O{sub 3}–Mn{sub 3}O{sub 4} glasses have been investigated as effect of Mn NPs content. • The magnetization measurement of glass sample is carried out using vibrating sample magnetometer (VSM)

  13. Red polymer light-emitting devices based on an oxadiazole-functionalized europium(III) complex

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yu, E-mail: liuyu03b@126.com [Department of Chemistry, Key Lab of Environment-Friendly Chemistry and Application in the Ministry of Education, Xiangtan University, Xiangtan 411105 (China); Wang, Yafei [Department of Chemistry, Key Lab of Environment-Friendly Chemistry and Application in the Ministry of Education, Xiangtan University, Xiangtan 411105 (China); Li, Chun [Institute of Polymer Optoelectronic Materials and Devices, South China University of Technology, Guangzhou 510640 (China); Huang, Ying; Dang, Dongfeng; Zhu, Meixiang [Department of Chemistry, Key Lab of Environment-Friendly Chemistry and Application in the Ministry of Education, Xiangtan University, Xiangtan 411105 (China); Zhu, Weiguo, E-mail: zhuwg18@126.com [Department of Chemistry, Key Lab of Environment-Friendly Chemistry and Application in the Ministry of Education, Xiangtan University, Xiangtan 411105 (China); Cao, Yong, E-mail: yongcao@scut.edu.cn [Institute of Polymer Optoelectronic Materials and Devices, South China University of Technology, Guangzhou 510640 (China)

    2014-02-14

    A novel tris(dibenzoylmethanato)[5-(2-(4-tert-butylbenzenyl)-5-benzenyl-1,3, 4-oxadiazole-4′)-1,10-phenanthroline]europium(III) [Eu(DBM){sub 3}(BuOXD-Phen)] containing an electron-transporting oxadiazole-functionalized phenanthroline ligand was synthesized and characterized. Its UV–vis absorption and photoluminescence (PL), as well as the electroluminescence (EL) in polymer light-emitting devices (PLEDs) were investigated. The double-layer PLEDs with a configuration of ITO/PEDOT:PSS (50 nm)/PVK (40 nm)/PFO:PBD (30%):Eu(DBM){sub 3}(BuOXD-Phen) (1–8 wt %) (80 nm)/Ba (4 nm)/Al (150 nm) were fabricated. Saturated red Eu{sup 3+} ion emission, based on the {sup 5}D{sub 0} → {sup 7}F{sub 2} transition, is centered at a wavelength of 614 nm with a full width at half maximum (FWHM) of 10 nm. The highest external quantum efficiency (QE{sub ext}) of 1.26% at current density of 1.65 mA cm{sup −2}, with a maximum brightness of 568 cd m{sup −2} at 137.8 mA cm{sup −2} was achieved from the device at 1 wt % dopant concentration. - Highlights: • An oxadiazole-functionalized europium(III) complex of Eu(DBM){sub 3}(BuOXD-Phen) was presented. • The optophysical properties of Eu(DBM){sub 3}(BuOXD-Phen) were investigated. • Saturated red emission was observed in the PLEDs. • An external quantum efficiency of 1.26% was obtained in these devices.

  14. Electron paramagnetic resonance and photoluminescence investigation of europium local structure in oxyfluoride glass ceramics containing SrF2 nanocrystals

    Science.gov (United States)

    Antuzevics, A.; Kemere, M.; Krieke, G.; Ignatans, R.

    2017-10-01

    Different compositions of europium doped aluminosilicate oxyfluoride glass ceramics prepared in air atmosphere have been studied by electron paramagnetic resonance (EPR) and optical spectroscopy methods. X-ray diffraction (XRD) and transmission electron microscopy (TEM) measurements show presence of homogenously distributed SrF2 nanocrystals after the heat treatment of the precursor glass. Efficient Eu3+ incorporation in the high symmetry environment of glass ceramics is observed from the photoluminescence spectra. EPR spectra indicate Eu3+ → Eu2+ reduction upon precipitation of crystalline phases in the glass matrix. For composition abundant with Eu2+ in the glassy state such behaviour is not detected. Local structure around europium ions is discussed based on differences in chemical compositions.

  15. Bright, highly water-soluble triazacyclononane europium complexes to detect ligand binding with time-resolved FRET microscopy.

    Science.gov (United States)

    Delbianco, Martina; Sadovnikova, Victoria; Bourrier, Emmanuel; Mathis, Gérard; Lamarque, Laurent; Zwier, Jurriaan M; Parker, David

    2014-09-26

    Luminescent europium complexes are used in a broad range of applications as a result of their particular emissive properties. The synthesis and application of bright, highly water-soluble, and negatively charged sulfonic- or carboxylic acid derivatives of para-substituted aryl-alkynyl triazacyclononane complexes are described. Introduction of the charged solubilizing moieties suppresses cellular uptake or adsorption to living cells making them applicable for labeling and performing assays on membrane receptors. These europium complexes are applied to monitor fluorescent ligand binding on cell-surface proteins with time-resolved Förster resonance energy transfer (TR-FRET) assays in plate-based format and using TR-FRET microscopy. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Optical and spectral studies on pure and europium doped olgite type Na(Sr,Ba)PO4 ceramics.

    Science.gov (United States)

    Jawaher, K Rackesh; Jagannathan, R; Das, S Jerome; Krishnan, S

    2015-04-05

    Europium ion doped olgite type Na(Sr,Ba)PO4 ceramics, a new generation of light emitting bulb, was prepared by a high temperature solid-state reaction method. The synthesized materials were subjected to various characterizations such as X-ray powder diffraction, Scanning electron microscopy and FT-IR spectra measurements. The EPR spectrum of the sample exhibits a well-resolved hyperfine structure of 151Eu2+ and 153Eu2+ isotopes and the g value has been calculated. Fluorescence spectra revealed that europium ions were present in divalent as well as in the trivalent oxidation states. The critical distance for energy transfer between Eu2+ and Eu2+ ion is calculated as 20Å, which is in good agreement with that of experimental data. The FTIR analysis reveals all the vibrations of PO4(3-) ions. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. A highly sensitive europium nanoparticle-based immunoassay for detection of influenza A/B virus antigen in clinical specimens.

    Science.gov (United States)

    Zhang, Panhe; Vemula, Sai Vikram; Zhao, Jiangqin; Du, Bingchen; Mohan, Haleyurgirisetty; Liu, Jikun; El Mubarak, Haja Sittana; Landry, Marie L; Hewlett, Indira

    2014-12-01

    We report the development of a novel europium nanoparticle-based immunoassay (ENIA) for rapid detection of influenza A and influenza B viruses. The ENIA demonstrated sensitivities of 90.7% (147/162) for influenza A viruses and 81.80% (9/11) for influenza B viruses compared to those for an in-house reverse transcription (RT)-PCR assay in testing of influenza-positive clinical samples. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

  18. Semiconducting polymer dots doped with europium complexes showing ultranarrow emission and long luminescence lifetime for time-gated cellular imaging.

    Science.gov (United States)

    Sun, Wei; Yu, Jiangbo; Deng, Ruiping; Rong, Yu; Fujimoto, Bryant; Wu, Changfeng; Zhang, Hongjie; Chiu, Daniel T

    2013-10-18

    Bright dots: Semiconducting polymer dots (Pdots) doped with europium complexes possess line-like fluorescence emission, high quantum yield, and long fluorescence lifetime. The Pdots successfully labeled receptors on cells. The long fluorescence lifetime of the Pdots was used to distinguish them from other red fluorescence emitting nanoparticles, and improve the signal-to-noise ratio for time-gated cellular imaging. PVK=poly(9-vinylcarbazole). Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Translocation and biokinetic behavior of nanoscaled europium oxide particles within 5 days following an acute inhalation in rats.

    Science.gov (United States)

    Creutzenberg, Otto; Kock, Heiko; Schaudien, Dirk

    2016-03-01

    Nanoscaled europium oxide (Eu2O3) particles were inhaled by rats after acute exposure and the potential translocation of particles followed by chemical analysis and transmission electron microscopy (TEM) was investigated. An aqueous dispersion (phosphate buffer/bovine serum albumin) of a commercially available Eu2O3 particle fraction consisting partially of nanoscaled particles was aerosolized with pressurized air. After rapid evaporation, rats inhaled the dry aerosol for 6 h in a single exposure resulting in an alveolar calculated dose of approximately 39.5 μg Eu2O3. Using chemical analysis, 36.8 μg Eu2O3 was detected 1 h after lung inhalation. The amount declined slightly to 34.5 μg after 1 day and 35.0 μg after 5 days. The liver showed an increase of Eu2O3 from 32.3 ng 1 h up to 294 ng 5 days after inhalation. Additionally, lung-associated lymph nodes, thymus, kidneys, heart and testis exhibited an increase of europium over the period investigated. In the blood, the highest amount of europium was found 1 h after treatment whereas feces, urine and mesenteric lymph nodes revealed the highest amount 1 day after treatment. Using TEM analysis, particles could be detected only in lungs, and in the liver, no particles were detectable. In conclusion, the translocation of Eu2O3 within 5 days following inhalation could be determined very precisely by chemical analysis. A translocation of Eu2O3 particulate matter to liver was not detectable by TEM analysis; thus, the overproportional level of 0.8% of the lung load observed in the liver after 5 days suggests a filtering effect of dissolved europium with accumulation. Copyright © 2015 John Wiley & Sons, Ltd.

  20. A Highly Sensitive Europium Nanoparticle-Based Immunoassay for Detection of Influenza A/B Virus Antigen in Clinical Specimens

    Science.gov (United States)

    Zhang, Panhe; Zhao, Jiangqin; Du, Bingchen; Mohan, Haleyurgirisetty; Liu, Jikun; El Mubarak, Haja Sittana; Landry, Marie L.

    2014-01-01

    We report the development of a novel europium nanoparticle-based immunoassay (ENIA) for rapid detection of influenza A and influenza B viruses. The ENIA demonstrated sensitivities of 90.7% (147/162) for influenza A viruses and 81.80% (9/11) for influenza B viruses compared to those for an in-house reverse transcription (RT)-PCR assay in testing of influenza-positive clinical samples. PMID:25297327

  1. Nature of the concentration thresholds of europium atom yield from the oxidized tungsten surface under electron stimulated desorption

    CERN Document Server

    Davydov, S Y

    2002-01-01

    The nature of the electron-stimulated desorption (ESD) of the europium atoms by the E sub e irradiating electrons energies, equal to 50 and 80 eV, as well as peculiarities of the Eu atoms yield dependence on their concentration on the oxidized tungsten surface are discussed. It is shown, that the ESD originates by the electron transition from the interval 5p- or 5s shell of the tungsten surface atom onto the oxygen external unfilled 2p-level

  2. Low-cost industrially available molybdenum boride and carbide as "platinum-like" catalysts for the hydrogen evolution reaction in biphasic liquid systems.

    Science.gov (United States)

    Scanlon, Micheál D; Bian, Xiaojun; Vrubel, Heron; Amstutz, Véronique; Schenk, Kurt; Hu, Xile; Liu, BaoHong; Girault, Hubert H

    2013-02-28

    Rarely reported low-cost molybdenum boride and carbide microparticles, both of which are available in abundant quantities due to their widespread use in industry, adsorb at aqueous acid-1,2-dichloroethane interfaces and efficiently catalyse the hydrogen evolution reaction in the presence of the organic electron donor - decamethylferrocene. Kinetic studies monitoring biphasic reactions by UV/vis spectroscopy, and further evidence provided by gas chromatography, highlight (a) their superior rates of catalysis relative to other industrially significant transition metal carbides and silicides, as well as a main group refractory compound, and (b) their highly comparable rates of catalysis to Pt microparticles of similar dimensions. Insight into the catalytic processes occurring for each adsorbed microparticle was obtained by voltammetry at the liquid-liquid interface.

  3. X-Ray photoelectron spectroscopy study of radiofrequency-sputtered titanium, carbide, molybdenum carbide, and titanium boride coatings and their friction properties

    Science.gov (United States)

    Brainard, W. A.; Wheeler, D. R.

    1977-01-01

    Radiofrequency sputtered coatings of titanium carbide, molybdenum carbide and titanium boride were tested as wear resistant coatings on stainless steel in a pin on disk apparatus. X-ray photoelectron spectroscopy (XPS) was used to analyze the sputtered films with regard to both bulk and interface composition in order to obtain maximum film performance. Significant improvements in friction behavior were obtained when properly biased films were deposited on deliberately preoxidized substrates. XPS depth profile data showed thick graded interfaces for bias deposited films even when adherence was poor. The addition of 10 percent hydrogen to the sputtering gas produced coatings with thin poorly adherent interfaces. Results suggest that some of the common practices in the field of sputtering may be detrimental to achieving maximum adherence and optimum composition for these refractory compounds.

  4. The coloring problem in the solid-state metal boride carbide ScB{sub 2}C{sub 2}. A theoretical analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lassoued, Souheila [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques; Universite Kasdi Merbah-Ouargla (Algeria). Faculte des Mathematiques et des Sciences de la Matiere; Boucher, Benoit [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques; Max-Planck-Institut fuer Chemische Physik Fester Stoffe, Dresden (Germany); Boutarfaia, Ahmed [Universite Kasdi Merbah-Ouargla (Algeria). Faculte des Mathematiques et des Sciences de la Matiere; Gautier, Regis; Halet, Jean-Francois [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques

    2016-08-01

    The electronic properties of the layered ternary metal boride carbide ScB{sub 2}C{sub 2}, the structure of which consists of B/C layers made of fused five- and seven-membered rings alternating with scandium sheets, are analyzed. In particular, the respective positions of the B and C atoms (the so-called coloring problem) are tackled using density functional theory, quantum theory of atoms in molecules, and electron localizability indicator calculations. Results reveal that (i) the most stable coloring minimizes the number of B-B and C-C contacts and maximizes the number of boron atoms in the heptagons, (ii) the compound is metallic in character, and (iii) rather important covalent bonding occurs between the metallic sheets and the boron-carbon network.

  5. Ultrasmall Superparamagnetic Iron Oxide Nanoparticles with Europium(III) DO3A as a Bimodal Imaging Probe.

    Science.gov (United States)

    Carron, Sophie; Bloemen, Maarten; Vander Elst, Luce; Laurent, Sophie; Verbiest, Thierry; Parac-Vogt, Tatjana N

    2016-03-18

    A new prototype consisting of ultrasmall superparamagnetic iron oxide (USPIO) nanoparticles decorated with europium(III) ions encapsulated in a DO3A organic scaffold was designed as a platform for further development of bimodal contrast agents for MRI and optical imaging. The USPIO nanoparticles act as negative MRI contrast agents, whereas the europium(III) ion is a luminophore that is suitable for use in optical imaging detection. The functionalized USPIO nanoparticles were characterized by TEM, DLS, XRD, FTIR, and TXRF analysis, and a full investigation of the relaxometric and optical properties was conducted. The typical luminescence emission of europium(III) was observed and the main red emission wavelength was found at 614 nm. The relaxometric study of these ultrasmall nanoparticles showed r2 values of 114.8 mM(-1) Fes(-1) at 60 MHz, which is nearly double the r2 relaxivity of Sinerem(®). © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. A lysosome targetable luminescent bioprobe based on a europium β-diketonate complex for cellular imaging applications.

    Science.gov (United States)

    George, T M; Krishna, Mahesh S; Reddy, M L P

    2016-11-22

    Herein, we report a novel lysosome targetable luminescent bioprobe derived from a europium coordination compound, namely Eu(pfphOCH3IN)3(DDXPO) 4 [where HpfphOCH3IN = 4,4,5,5,5-pentafluoro-3-hydroxy-1-(1-(4-methoxyphenyl)-1H-indol-3-yl)pent-2-en-1-one and DDXPO = 4,5-bis(diphenylphosphino)-9,9-dimethylxanthene oxide]. Notably, the newly designed europium complex exhibits significant quantum yield (Φoverall = 25 ± 3%) and 5D0 excited state lifetime (τ = 398 ± 3 μs) values under physiological pH (7.2) conditions when excited at 405 nm. Hence the developed europium complex has been evaluated for live cell imaging applications using mouse pre-adipocyte cell lines (3T3L1). Colocalization studies of the designed bio-probe with commercial Lysosome-GFP in 3T3L1 cells demonstrated the specific localization of the probe in the lysosome with a high colocalization coefficient (A = 0.83). Most importantly, the developed bioprobe exhibits good cell permeability, photostability and non-cytotoxicity.

  7. Mössbauer spectroscopy of europium-doped fluorochlorozirconate glasses and glass ceramics: optimization of storage phosphors in computed radiography.

    Science.gov (United States)

    Pfau, C; Paßlick, C; Gray, S K; Johnson, J A; Johnson, C E; Schweizer, S

    2013-05-22

    Eu(2+)-doped fluorochlorozirconate (FCZ) glasses and glass ceramics, which are being developed for medical and photovoltaic applications, have been analysed by Mössbauer spectroscopy. The oxidation state and chemical environment of the europium ions, which are important for the performance of these materials, were investigated. Routes for maximizing the divalent europium content were also investigated. By using EuCl2 instead of EuF2 in the starting material a fraction of about 90% of the europium was maintained in the Eu(2+) state as opposed to about 70% when using EuF2. The glass ceramics produced by subsequent thermal processing contain BaCl2 nanocrystals in which Eu(2+) is incorporated, as shown by the narrower linewidth in the Mössbauer spectrum. Debye temperatures of 147 K and 186 K for Eu(2+) and Eu(3+), respectively, were determined from temperature dependent Mössbauer measurements. The f-factors were used to obtain the Eu(2+)/Eu(3+) ratio from the area ratio of the corresponding absorption lines.

  8. Synthesis, boron-nonstoichiometry and hardness of perovskite-type rare earth rhodium borides RRh{sub 3}B {sub x} (R = La, Gd, Lu and Sc)

    Energy Technology Data Exchange (ETDEWEB)

    Shishido, T. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan)]. E-mail: shishido@imr.tohoku.ac.jp; Ye, J. [National Institute for Materials Science, 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Okada, S. [Faculty of Engineering, Kokushikan University, 4-28-1 Setagaya-ku, Tokyo 154-8515 (Japan); Kudou, K. [Faculty of Engineering, Kanagawa University, 3-27-1 Rokkakubashi, Kanagawa-ku, Yokohama 221-8686 (Japan); Iizumi, K. [Faculty of Engineering, Tokyo Institute of Polytechnics, 1583 Iiyama, Atsugi 243-0297 (Japan); Oku, M. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Ishizawa, Y. [Department of Environmental Science, Iwaki Meisei University, 5-5-1 Iino, Chuohdai, Iwaki 970-8551 (Japan); Sahara, R.; Kumar, V. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Yoshikawa, A. [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Tanaka, M. [Photon Factory, High Energy Accelerator Research Organization, 1-1 Oho, Tsukuba 305-0801 (Japan); Horiuchi, H. [Earth Science Laboratory, Faculty of Education, Hirosaki University, 1 Bunkyo-cho, Hirosaki 036-8560 (Japan); Nomura, A.; Sugawara, T.; Obara, K. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Amano, T. [Shonan Institute of Technology, 1-1-25, Tsujido-Nishikaigan, Fujisawa 251-8511 (Japan); Kohiki, S. [Department of Materials Science, Kyusyu Institute of Technology, Kita-Kyusyu 804-8550 (Japan); Kawazoe, Y.; Nakajima, K. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan)

    2006-02-09

    Rare earth ternary borides, RRh{sub 3}B {sub x} (R = La, Gd, Lu and Sc) have been synthesized by arc melting method. Borides RRh{sub 3}B {sub x} (R = La, Gd, Lu and Sc) have perovskite-type cubic structure: space group Pm3m; Z = 1. The lattice parameters a of the stoichiometric RRh{sub 3}B for R = La, Gd, Lu and Sc are 0.4251(1), 0.4183(1), 0.4126(1) and 0.4080(1) nm, respectively. LaRh{sub 3}B {sub x} does not have boron-nonstoichiometry as x = 0. In GdRh{sub 3}B {sub x} and LuRh{sub 3}B {sub x}, boron- nonstoichiometry ranges between 0.55 {<=} x {<=} 1 and 0.30 {<=} x {<=} 1, respectively. The boron-nonstoichiometry range is the widest, 0 {<=} x {<=} 1, for R = Sc. Boron-nonstoichiometry increases with decreasing atomic radius of R. The microhardness of the stoichiometric RRh{sub 3}B for R = La, Gd, Lu and Sc is 4.2 {+-} 0.1, 6.8 {+-} 0.1, 7.7 {+-} 0.5 and 9.9 {+-} 0.1 GPa, respectively. As a result, microhardness increases with decreasing atomic size of R in RRh{sub 3}B; R is positioned at the eight corners of the cube in the perovskite-type structure. Thus, hardness is strongly dependent on R element. The hardness changes almost linearly with boron concentration x for R = Gd and Lu in RRh{sub 3}B {sub x}, while no linear dependency is found for R = Sc. Ab initio calculations have been performed to obtain the equilibrium lattice constants and the bulk moduli. The calculated lattice constants are in excellent agreement with experimental results.

  9. Fast and Selective Preconcentration of Europium from Wastewater and Coal Soil by Graphene Oxide/Silane@Fe3O4 Dendritic Nanostructure.

    Science.gov (United States)

    Patra, Santanu; Roy, Ekta; Madhuri, Rashmi; Sharma, Prashant K

    2015-05-19

    In this study, nanocomposite of graphene oxide and silane modified magnetic nanoparticles (silane@Fe3O4) were synthesized in a form of dendritic structure. For this, silane@Fe3O4 nanoparticle gets sandwiched between two layers of graphene oxide by chemical synthesis route. The synthesized dendritic structure was used as a monomer for synthesis of europium ion imprinted polymer. The synthesis of imprinted polymer was contemplated onto the surface of the vinyl group modified silica fiber by activated generated free radical atom-transfer radical polymerization, that is, AGET-ATRP technique. The synthesized dendritic monomer was characterized by XRD, FT-IR, VSM, FE-SEM, and TEM analyses. The imprinted polymer modified silica fiber was first validated in the aqueous and blood samples for successful extraction and detection of europium ion with limit of detection = 0.050 pg mL(-1) (signal/noise = 3). The imprinted polymer modified silica fiber was also used for preconcentration and separation of europium metal ion from various soil samples of coal mine areas. However, the same silica fiber was also used for wastewater treatment and shows 100% performance for europium removal. The findings herein suggested that dendritic nanocomposite could be potentially used as a highly effective material for the enrichment and preconcentration of europium or other trivalent lanthanides/actinides in nuclear waste management.

  10. Development of europium doped core-shell silica cobalt ferrite functionalized nanoparticles for magnetic resonance imaging.

    Science.gov (United States)

    Kevadiya, Bhavesh D; Bade, Aditya N; Woldstad, Christopher; Edagwa, Benson J; McMillan, JoEllyn M; Sajja, Balasrinivasa R; Boska, Michael D; Gendelman, Howard E

    2017-02-01

    The size, shape and chemical composition of europium (Eu3+) cobalt ferrite (CFEu) nanoparticles were optimized for use as a "multimodal imaging nanoprobe" for combined fluorescence and magnetic resonance bioimaging. Doping Eu3+ ions into a CF structure imparts unique bioimaging and magnetic properties to the nanostructure that can be used for real-time screening of targeted nanoformulations for tissue biodistribution assessment. The CFEu nanoparticles (size ∼7.2nm) were prepared by solvothermal techniques and encapsulated into poloxamer 407-coated mesoporous silica (Si-P407) to form superparamagnetic monodisperse Si-CFEu nanoparticles with a size of ∼140nm. Folic acid (FA) nanoparticle decoration (FA-Si-CFEu, size ∼140nm) facilitated monocyte-derived macrophage (MDM) targeting. FA-Si-CFEu MDM uptake and retention was higher than seen with Si-CFEu nanoparticles. The transverse relaxivity of both Si-CFEu and FA-Si-CFEu particles were r2=433.42mM-1s-1 and r2=419.52mM-1s-1 (in saline) and r2=736.57mM-1s-1 and r2=814.41mM-1s-1 (in MDM), respectively. The results were greater than a log order-of-magnitude than what was observed at replicate iron concentrations for ultrasmall superparamagnetic iron oxide (USPIO) particles (r2=31.15mM-1s-1 in saline) and paralleled data sets obtained for T2 magnetic resonance imaging. We now provide a developmental opportunity to employ these novel particles for theranostic drug distribution and efficacy evaluations. A novel europium (Eu3+) doped cobalt ferrite (Si-CFEu) nanoparticle was produced for use as a bioimaging probe. Its notable multifunctional, fluorescence and imaging properties, allows rapid screening of future drug biodistribution. Decoration of the Si-CFEu particles with folic acid increased its sensitivity and specificity for magnetic resonance imaging over a more conventional ultrasmall superparamagnetic iron oxide particles. The future use of these particles in theranostic tests will serve as a platform for

  11. Tuning Eu{sup 3+} emission in europium sesquioxide films by changing the crystalline phase

    Energy Technology Data Exchange (ETDEWEB)

    Mariscal, A., E-mail: antonio.mariscal@csic.es [Laser Processing Group, Instituto de Óptica, CSIC, C/ Serrano 121, 28006 Madrid (Spain); Quesada, A. [Ceramics for Smart Systems Group, Instituto de Cerámica y Vidrio, C/ Kelsen 5, 28049 Madrid (Spain); Camps, I. [Laser Processing Group, Instituto de Óptica, CSIC, C/ Serrano 121, 28006 Madrid (Spain); Palomares, F.J. [Instituto de Ciencia de Materiales de Madrid, C/ Sor Juana Inés de la Cruz 3, 28049 Madrid (Spain); Fernández, J.F. [Ceramics for Smart Systems Group, Instituto de Cerámica y Vidrio, C/ Kelsen 5, 28049 Madrid (Spain); Serna, R. [Laser Processing Group, Instituto de Óptica, CSIC, C/ Serrano 121, 28006 Madrid (Spain)

    2016-06-30

    Highlights: • PLD production of high quality europium sesquioxide (Eu{sub 2}O{sub 3}) films. • The deposition of Al{sub 2}O{sub 3} capping and/or buffer layers modifies the crystallization for Eu{sub 2}O{sub 3} films upon annealing. • The formation of cubic or monoclinic phases can be favored. • Eu{sup 3+} emission tuning is achieved as a consequence of crystal field effects. - Abstract: We report the growth of europium sesquioxide (Eu{sub 2}O{sub 3}) thin films by pulsed laser deposition (PLD) in vacuum at room temperature from a pure Eu{sub 2}O{sub 3} ceramic bulk target. The films were deposited in different configurations formed by adding capping and/or buffer layers of amorphous aluminum oxide (a-Al{sub 2}O{sub 3}). The optical properties, refractive index and extinction coefficient of the as deposited Eu{sub 2}O{sub 3} layers were obtained. X-ray photoelectron spectroscopy (XPS) measurements were done to assess its chemical composition. Post-deposition annealing was performed at 500 °C and 850 °C in air in order to achieve the formation of crystalline films and to accomplish photoluminescence emission. According to the analysis of X-ray diffraction (XRD) spectra, cubic and monoclinic phases were formed. It is found that the relative amount of the phases is related to the different film configurations, showing that the control over the crystallization phase can be realized by adequately designing the structures. All the films showed photoluminescence emission peaks (under excitation at 355 nm) that are attributed to the intra 4f-transitions of Eu{sup 3+} ions. The emission spectral shape depends on the crystalline phase of the Eu{sub 2}O{sub 3} layer. Specifically, changes in the hypersensitive {sup 5}D{sub 0} → {sup 7}F{sub 2} emission confirm the strong influence of the crystal field effect on the Eu{sup 3+} energy levels.

  12. A Study on the Effect of the Boron Potential on the Mechanical Properties of the Borided Layers Obtained by Boron Diffusion at the Surface of AISI 316L Steel

    Directory of Open Access Journals (Sweden)

    E. Hernández-Sánchez

    2014-01-01

    Full Text Available The effect of the boron potential on the thickness and the mechanical properties of borided layers was evaluated. The boron potential was established by means of the available atoms of boron contained in a control volume inside a cylinder. The cylinders were manufactured from AISI 316L steel, and the boriding treatment was performed using the powder pack technique at a temperature of 1273 K over an exposure time of 6 h. Four different internal diameters of the cylinders were evaluated (3.17, 4.76, 6.35, and 7.93 mm. The mechanical properties were evaluated using the Berkovich instrumented indentation technique. The results showed a clear influence of the boron potential on the mechanical properties of the layers. The hardness of the layers was stablished in the range of 16.22 to 21.16 GPa. Young’s modulus values were stablished in the range of 255.96 to 341.37 GPa. Also the fracture toughness and brittleness of the layers reflected the influence of the boron potential supplied during the boriding process. Finally, the influence of the boron potential on the constant of parabolic growth (K was also established as a function of the inner diameter of the cylinders.

  13. Highly efficient precipitation of phosphoproteins using trivalent europium, terbium, and erbium ions

    Energy Technology Data Exchange (ETDEWEB)

    Guezel, Yueksel; Rainer, Matthias; Mirza, Munazza Raza; Bonn, Guenther K. [Leopold-Franzens University, Institute of Analytical Chemistry and Radiochemistry, Innsbruck (Austria)

    2012-05-15

    This study describes a highly efficient method for the selective precipitation of phosphoproteins by trivalent europium, terbium, and erbium metal ions. These metal cations belong to the group of lanthanides and are known to be hard acceptors with an overwhelming preference for oxygen-containing anions such as phosphates to which they form very tight ionic bonds. The method could be successfully applied to specifically precipitate phosphoproteins from complex samples including milk and egg white by forming solid metal-protein complexes. Owing to the low solubility product of the investigated lanthanide salts, the produced metal-protein complexes showed high stability. The protein pellets were extensively washed to remove nonphosphorylated proteins and contaminants. For the analysis of proteins the pellets were first dissolved in 30 % formic acid and subjected to matrix-assisted laser desorption/ionization-time of flight (MALDI-TOF) MS. For peptide mass-fingerprint analysis the precipitated phosphoproteins were enzymatically digested using microwave-assisted digestion. The method was found to be highly specific for the isolation and purification of phosphoproteins. Protein quantification was performed by colorimetric detection of total precipitated phosphoproteins and revealed more than 95 % protein recovery for each lanthanide salt. (orig.)

  14. Effects of europium polyoxometalate encapsulated in silica nanoparticles (nanocarriers) in soil invertebrates

    Science.gov (United States)

    Bicho, Rita C.; Soares, Amadeu M. V. M.; Nogueira, Helena I. S.; Amorim, Mónica J. B.

    2016-12-01

    Polyoxometalates (POMs) are metal oxo clusters that have been investigated for several applications in material sciences, catalysis, and biomedicine; these gained increasing interest in the field of nanotechnology as nanocarriers for drug delivery. Associated to the increasing applications, there is the need for information regarding the effects on the environment of these compounds, which is completely absent in the literature. In the present study, the effects of europium polyoxometalates encapsulated into silica nanoparticles (Eu-POM/SiO2 NPs) were assessed on the soil representative Enchytraeus crypticus. The individual materials were also assessed (Eu-POMs and SiO2 NPs). Toxicity was evaluated in various test media with increasing complexity: water, soil/water extracts, and soil. Toxicity was only observed for Eu-POM/SiO2 NPs and in the presence of soil components. Despite the fact that effects were observed for concentrations higher than current predicted environmental concentration (PEC), attention should be given to the growing use of these compounds. The present study shows the importance of assessing the effects in soil media, also compared to water. Moreover, results of "no effect" are critically needed and often unpublished. The present study can contribute to the improvement of the OECD guidelines for safety of manufactured nanomaterials on environmental toxicity in the soil compartment providing an improved test alternative.

  15. Spectral Interferences Manganese (Mn) - Europium (Eu) Lines in X-Ray Fluorescence Spectrometry Spectrum

    Science.gov (United States)

    Tanc, Beril; Kaya, Mustafa; Gumus, Lokman; Kumral, Mustafa

    2016-04-01

    X-ray fluorescence (XRF) spectrometry is widely used for quantitative and semi quantitative analysis of many major, minor and trace elements in geological samples. Some advantages of the XRF method are; non-destructive sample preparation, applicability for powder, solid, paste and liquid samples and simple spectrum that are independent from chemical state. On the other hand, there are some disadvantages of the XRF methods such as poor sensitivity for low atomic number elements, matrix effect (physical matrix effects, such as fine versus course grain materials, may impact XRF performance) and interference effect (the spectral lines of elements may overlap distorting results for one or more elements). Especially, spectral interferences are very significant factors for accurate results. In this study, semi-quantitative analyzed manganese (II) oxide (MnO, 99.99%) was examined. Samples were pelleted and analyzed with XRF spectrometry (Bruker S8 Tiger). Unexpected peaks were obtained at the side of the major Mn peaks. Although sample does not contain Eu element, in results 0,3% Eu2O3 was observed. These result can occur high concentration of MnO and proximity of Mn and Eu lines. It can be eliminated by using correction equation or Mn concentration can confirm with other methods (such as Atomic absorption spectroscopy). Keywords: Spectral Interferences; Manganese (Mn); Europium (Eu); X-Ray Fluorescence Spectrometry Spectrum.

  16. Performance of fluorescent europium(III) nanoparticles and colloidal gold reporters in lateral flow bioaffinity assay.

    Science.gov (United States)

    Juntunen, Etvi; Myyryläinen, Tiina; Salminen, Teppo; Soukka, Tero; Pettersson, Kim

    2012-09-01

    Lateral flow (LF) immunoassays (i.e., immunochromatographic assays) have traditionally been applied to analytes that do not require very high analytical sensitivity or quantitative results. The selection of potential analytes is often limited by the performance characteristics of the assay technology. Analytes with more demanding sensitivity requirements call for reporter systems enabling high analytical sensitivity. In this study, we systematically compared the performance of fluorescent europium(III) [Eu(III)] chelate dyed polystyrene nanoparticles and colloidal gold particles in lateral flow assays. The effect of time-resolved measurement mode was also studied. Because binder molecules used in immunoassays might not behave similarly when conjugated to different reporter particles, two model assays were constructed to provide reliable technical comparison of the two reporter systems. The comparative experiment demonstrated that the fluorescent nanoparticles yielded 7- and 300-fold better sensitivity compared with colloidal gold in the two test systems, respectively. Although the two reporter particles may induce variable effects using individual binders, overall the high specific activity of Eu(III) nanoparticles has superior potential over colloidal gold particles for the development of robust high-sensitivity bioaffinity assays. Copyright © 2012 Elsevier Inc. All rights reserved.

  17. Carbon nanotube-loaded Nafion film electrochemical sensor for metal ions: europium.

    Science.gov (United States)

    Wang, Tingting; Zhao, Daoli; Guo, Xuefei; Correa, Jaime; Riehl, Bill L; Heineman, William R

    2014-05-06

    A Nafion film loaded with novel catalyst-free multiwalled carbon nanotubes (MWCNTs) was used to modify a glassy carbon (GC) electrode to detect trace concentrations of metal ions, with europium ion (Eu(3+)) as a model. The interaction between the sidewalls of MWCNTs and the hydrophobic backbone of Nafion allows the MWCNTs to be dispersed in Nafion, which was then coated as a thin film on the GC electrode surface. The electrochemical response to Eu(3+) was found to be ∼10 times improved by MWCNT concentrations between 0.5 and 2 mg/mL, which effectively expanded the electrode surface into the Nafion film and thereby reduced the diffusion distance of Eu(3+) to the electrode surface. At low MWCNT concentrations of 0.25 and 0.5 mg/mL, no significant improvement in signal was obtained compared with Nafion alone. Scanning electron microscopy and electrochemical impedance spectroscopy were used to characterize the structure of the MWCNT-Nafion film, followed by electrochemical characterization with Eu(3+) via cyclic voltammetry and preconcentration voltammetry. Under the optimized conditions, a linear range of 1-100 nM with a calculated detection limit of 0.37 nM (signal/noise = 3) was obtained for determination of Eu(3+) by Osteryoung square-wave voltammetry after a preconcentration time of 480 s.

  18. Effects of europium polyoxometalate encapsulated in silica nanoparticles (nanocarriers) in soil invertebrates

    Energy Technology Data Exchange (ETDEWEB)

    Bicho, Rita C., E-mail: ritabicho@ua.pt; Soares, Amadeu M.V.M. [Universidade de Aveiro, Departamento de Biologia & CESAM (Portugal); Nogueira, Helena I.S. [Universidade de Aveiro, Departamento de Química & CICECO (Portugal); Amorim, Mónica J.B. [Universidade de Aveiro, Departamento de Biologia & CESAM (Portugal)

    2016-12-15

    Polyoxometalates (POMs) are metal oxo clusters that have been investigated for several applications in material sciences, catalysis, and biomedicine; these gained increasing interest in the field of nanotechnology as nanocarriers for drug delivery. Associated to the increasing applications, there is the need for information regarding the effects on the environment of these compounds, which is completely absent in the literature. In the present study, the effects of europium polyoxometalates encapsulated into silica nanoparticles (Eu-POM/SiO{sub 2} NPs) were assessed on the soil representative Enchytraeus crypticus. The individual materials were also assessed (Eu-POMs and SiO{sub 2} NPs). Toxicity was evaluated in various test media with increasing complexity: water, soil/water extracts, and soil. Toxicity was only observed for Eu-POM/SiO{sub 2} NPs and in the presence of soil components. Despite the fact that effects were observed for concentrations higher than current predicted environmental concentration (PEC), attention should be given to the growing use of these compounds. The present study shows the importance of assessing the effects in soil media, also compared to water. Moreover, results of “no effect” are critically needed and often unpublished. The present study can contribute to the improvement of the OECD guidelines for safety of manufactured nanomaterials on environmental toxicity in the soil compartment providing an improved test alternative.

  19. EUROPIUM ION INFLUENCE ON THE FORMATION OF Ag-NANOPARTICLES IN FLUORINE PHOSPHATE GLASSES

    Directory of Open Access Journals (Sweden)

    R. O. Pysh'ev

    2015-05-01

    Full Text Available The paper deals with research of formation characteristics of silver nanoparticles in fluorophosphate glasses 0.25 Na2O - 0.5 P2O5 - 0.10 Ga2O3 - 0.075 AlF3 - 0.025 NaF - 0.05 ZnF2 doped with EuF3 (0.8 and 4 wt.% and without them. The synthesis was carried out in closed glassy carbon crucibles in argon atmosphere. Nanoparticles were formed after a low temperature process of Ag+ → Na+ ion-exchange (320 °C and subsequent heat treatment. It was shown that in the initial glasses doped with EuF3, rare earth ions exist in two valence forms (Eu2+ and Eu3+ in dynamic equilibrium and the concentration of Eu2+ increases proportionally to the total concentration of fluoride. It was shown that sizes of molecular clusters or metal nanoparticles depend on the concentration of europium fluoride and duration of ion exchange. The metallic Ag-nanoparticles sizes were defined for different times of heat treatment and ion exchange. The possibility of the stimulating growth of nanoparticles through the introduction of additional EuF3 in the glass was proved. The possibility of obtaining nanoparticles without the heat treatment in glasses with a high concentration of EuF3 was shown. Chemical mechanism for the formation of Ag-nanoparticles during the ion exchange was suggested.

  20. Nanoparticles in the zirconia-europium niobate system via hydrothermal route.

    Science.gov (United States)

    Hirano, Masanori; Dozono, Hayato

    2013-10-01

    The effect of the composition on the hydrothermal formation, structure, and properties of nanocrystalline luminescent materials in the zirconia (ZrO2)-europium niobate 1/4(Eu3NbO7) system was investigated. In the composition range 40 particles with crystallite size 6.0-7.6 nm that were hydrothermally formed from the precursor solutions of NbCl5, ZrOCI2, and EuCl3 under weakly basic conditions at 240 degrees C showed cubic structure. The lattice parameter when estimated as a single cubic phase linearly decreased as the concentration of ZrO2 increased. The presence of zirconia component effectively promoted the formation of nanocrystals containing the niobate, Eu3NbO7 under hydrothermal condition. The nanocrystalline particles could be excited by ultraviolet light 395 nm (f-f transition) and emitted orange (590 nm) and red light (610 nm) corresponding to 5D0 --> 7F1 and 5D0 --> 7F2 transitions of Eu3+, respectively. The intensity of the electric dipole transition (5D0 --> 7F2) that was expressed in values relative to the magnetic dipole transition (5D0 --> 7F1) increased with increased heat-treatment temperature in the range from 950 to 1200 degrees C.

  1. Photoluminescence of monocrystalline and stain-etched porous silicon doped with high temperature annealed europium

    Energy Technology Data Exchange (ETDEWEB)

    Guerrero-Lemus, R; Montesdeoca-Santana, A; Gonzalez-Diaz, B; Diaz-Herrera, B; Hernandez-Rodriguez, C; Jimenez-Rodriguez, E [Departamento de Fisica Basica, Universidad de La Laguna (ULL), Avenida AstrofIsico Francisco Sanchez, 2. 38206 La Laguna, Tenerife (Spain); Velazquez, J J, E-mail: rglemus@ull.es [Departamento de Fisica Fundamental y Experimental, Electronica y Sistemas, Universidad de La Laguna (ULL), Avenida Astrofisico Francisco Sanchez, 2. 38206 La Laguna, Tenerife (Spain)

    2011-08-24

    In this work, for the first time, the photoluminescent emission and excitation spectra of non-textured layers and stain-etched porous silicon layers (PSLs) doped with high temperature annealed europium (Eu) are evaluated. The PSLs are evaluated as a host for rare earth ions and as an antireflection coating. The applied doping process, which consists in a simple impregnation method followed by a high-temperature annealing step, is compatible with the standard processes in the fabrication of solar cells. The results show down-shifting processes with a maximum photoluminescent intensity at 615 nm, related to the transition {sup 5}D{sub 0} {yields} {sup 7}F{sub 2}. Different initial concentrations of Eu(NO{sub 3}){sub 3} are evaluated to study the influence of the rare earth concentration on the photoluminescent intensity. The chemical composition and the morphology of Eu-doped PSLs are examined by means of x-ray dispersion spectroscopy, Fourier-transform infrared spectroscopy and scanning electron microscopy. These Eu-doped layers are considered to be applied as energy converters in silicon-based third generation solar cells.

  2. Europium (III) and Uranium (VI) complexation by natural organic matter (NOM): Effect of source.

    Science.gov (United States)

    Kautenburger, Ralf; Sander, Jonas M; Hein, Christina

    2017-03-01

    For the safe long-term storage of high-level radioactive waste (HLW), detailed information about geo-chemical behavior of radioactive and toxic metal ions under environmental conditions is important. Natural organic matter (NOM) can play a crucial role in the immobilization or mobilization of these metal ions due to its complexation and colloid formation tendency. In this study, the complexation of europium (as chemical homologue of trivalent actinides such as americium) and uranium (as main component of HLW) by ten humic acids (HA) from different sources and Suwannee NOM river extract has been analyzed. Capillary electrophoresis in combination with inductively coupled plasma mass spectrometry has been used for the evaluation of complex stability constants log β. In order to determine the complex stability constants a conservative single site model was used in this study. In dependence of their source and thus of NOM structure the log β values for the analyzed humic acids are in the range of 6.1-7.0 for Eu(III) and 5.2-6.4 for U(VI) (UO 2 2+ ), respectively. In contrast to the results for HA the used Suwannee river NOM reveals log β values in the range of nearly two orders of magnitude lower (4.6 for Eu 3+ and 4.5 for UO 2 2+ ) under the geochemical conditions applied in this study. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Europium incorporated into titanium oxide by the sol-gel method

    Directory of Open Access Journals (Sweden)

    Lucas Alonso Rocha

    2005-09-01

    Full Text Available In this work titanium sol was prepared from tetraethylorthotitanate (TEOT in ethanol, stabilized with beta-diketonate 2,4 pentanedione in molar ratio 1:1 homogenized by magnetic stirring, europium ion was add as structural probe. The xerogels were heat treated at 500, 750 and 1000 °C and the characterization was realized by x-ray diffraction (XRD, transmission electron microscopy (TEM, thermogravimetric analysis (TGA/DSC and photoluminescence (PL. The excitation spectra of Eu (III ion present maximum in 394 nm correspondent to 5L6 level and emission spectra present bands characteristic transitions arising from the 5 D0 -> 7F J (J = 0, 1, 2, 3, 4 manifolds to samples treat at 500 and 750 °C. The Eu (III emission disappear, when heated at 1000 °C, probably due to phase transition anatase to rutile and migrations of ions to the external surface that was proved by x-ray diffraction, transmission electronic microscopy and the thermogravimetric analyses of xerogels.

  4. Luminescence studies on the europium doped strontium metasilicate phosphor prepared by solid state reaction method

    Directory of Open Access Journals (Sweden)

    Ishwar Prasad Sahu

    2017-03-01

    Full Text Available Europium doped strontium meta-silicate (namely SrSiO3:Eu3+ phosphor was prepared by a high temperature solid state reaction method. The sintered SrSiO3:Eu3+ phosphor possesses a monoclinic structure by the XRD. Energy dispersive X-ray spectrum (EDS confirms the presence of elements in the desired sample. Thermoluminescence (TL kinetic parameters such as activation energy (E, order of kinetics (b, and frequency factor (s were calculated by the peak shape method. The orange–red emission was shown to originate from the 5D0–7FJ (J = 0, 1, 2, 3, 4 transitions of Eu3+ ions as the sample was excited at 396 nm. The SrSiO3:Eu3+ phosphor with almost pure orange-red color purity (99.62% shows the quantum efficiency of 10.2% (excited by 396 nm, which is higher than those of commercial red phosphors Y2O3:Eu3+ and Y2O2S:Eu3+ with quantum efficiencies of 9.6% (excited by 394 nm and 4.2% (excited by 395 nm, respectively. Mechanoluminescence (ML intensity of the SrSiO3:Eu3+ phosphor was also found to increase linearly with increasing the impact velocity of the moving piston, suggesting that the discussed phosphor can be used as a stress sensor.

  5. Europium Luminescence Used for Logic Gate and Ions Sensing with Enoxacin As the Antenna.

    Science.gov (United States)

    Lu, Lixia; Chen, Chuanxia; Zhao, Dan; Sun, Jian; Yang, Xiurong

    2016-01-19

    Luminescent lanthanide ion complexes have received increasing attention because of their unique optical properties. Herein, we discovered that the luminescence of europium(III) (Eu(3+)) could be regulated by Ag(+) and SCN(-) in seconds with enoxacin (ENX) as the antenna. Under given conditions, only the simultaneous introduction of Ag(+) and SCN(-) could remarkably enhance the luminescence intensity of Eu(3+)-ENX complexes. This phenomenon has been exploited to design an "AND" logic gate and specific luminescence turn-on assays for sensitively sensing Ag(+) and SCN(-) for the first time. Furthermore, the addition of S(2-) resulted in efficient luminescence quenching of the Eu(3+)/ENX/Ag(+)/SCN(-) system due to the strong affinity between Ag(+) and S(2-). Thus, a new luminescent sensing platform for S(2-) was established, which exhibited excellent selectivity and high sensitivity. S(2-) could be detected within the concentration range of 100 nM to 12.5 μM with a detection limit of 60 nM. Such sensing system features simplicity, rapidity, and flexibility. Moreover, this proposed Eu(3+)-based luminescent assay could be successfully applied in the real environmental water sample analysis.

  6. Radiation effects on beta 10.6 of pure and europium doped KCl

    Science.gov (United States)

    Grimes, H. H.; Maisel, J. E.; Hartford, R. H.

    1975-01-01

    Changes in the optical absorption coefficient as a result of X-ray and electron bombardment of pure KCl (monocrystalline and polycrystalline), and divalent europium doped polycrystalline KCl were determined. The optical absorption coefficients were measured by a constant heat flow calorimetric method. Both 300 KV X-irradiation and 2 MeV electron irradiation produced significant increases in beta 10.6, measured at room temperature. The X-irradiation of pure moncrystalline KCl increased beta 10.6 by 0.005/cm for a 113 MR dose. For an equivalent dose, 2 MeV electrons were found less efficient in changing beta 10.6. However, electron irradiation of pure and Eu-doped polycrystalline KCl produced marked increases in adsorption. Beta increased to over 0.25/cm in Eu-doped material for a 30 x 10 to the 14th power electrons/sq cm dose, a factor of 20 increase over unirradiated material. Moreover, bleaching the electron irradiated doped KCl with 649 m light produced and additional factor of 1.5 increase. These findings will be discussed in light of known defect-center properties in KCl.

  7. Accelerating the clearance of mutant huntingtin protein aggregates through autophagy induction by europium hydroxide nanorods.

    Science.gov (United States)

    Wei, Peng-Fei; Zhang, Li; Nethi, Susheel Kumar; Barui, Ayan Kumar; Lin, Jun; Zhou, Wei; Shen, Yi; Man, Na; Zhang, Yun-Jiao; Xu, Jing; Patra, Chitta Ranjan; Wen, Long-Ping

    2014-01-01

    Autophagy is one of the well-known pathways to accelerate the clearance of protein aggregates, which contributes to the therapy of neurodegenerative diseases. Although there are numerous reports that demonstrate the induction of autophagy with small molecules including rapamycin, trehalose and lithium, however, there are few reports mentioning the clearance of aggregate-prone proteins through autophagy induction by nanoparticles. In the present article, we have demonstrated that europium hydroxide [Eu(III)(OH)3] nanorods can reduce huntingtin protein aggregation (EGFP-tagged huntingtin protein with 74 polyQ repeats), responsible for neurodegenerative diseases. Again, we have found that these nanorods induce authentic autophagy flux in different cell lines (Neuro 2a, PC12 and HeLa cells) through the expression of higher levels of characteristic autophagy marker protein LC3-II and degradation of selective autophagy substrate/cargo receptor p62/SQSTM1. Furthermore, depression of protein aggregation clearance through the autophagy blockade has also been observed by using specific inhibitors (wortmannin and chloroquine), indicating that autophagy is involved in the degradation of huntingtin protein aggregation. Since [Eu(III)(OH)3] nanorods can enhance the degradation of huntingtin protein aggregation via autophagy induction, we strongly believe that these nanorods would be useful for the development of therapeutic treatment strategies for various neurodegenerative diseases in near future using nanomedicine approach. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. High-resolution Thermal Micro-imaging Using Europium Chelate Luminescent Coatings.

    Science.gov (United States)

    Benseman, Timothy M; Hao, Yang; Vlasko-Vlasov, Vitalii K; Welp, Ulrich; Koshelev, Alexei E; Kwok, Wai-Kwong; Divan, Ralu; Keiser, Courtney; Watanabe, Chiharu; Kadowaki, Kazuo

    2017-04-16

    Micro-electronic devices often undergo significant self-heating when biased to their typical operating conditions. This paper describes a convenient optical micro-imaging technique which can be used to map and quantify such behavior. Europium thenoyltrifluoroacetonate (EuTFC) has a 612 nm luminescence line whose activation efficiency drops strongly with increasing temperature, due to T-dependent interactions between the Eu3+ ion and the organic chelating compound. This material may be readily coated on to a sample surface by thermal sublimation in vacuum. When the coating is excited with ultraviolet light (337 nm) an optical micro-image of the 612 nm luminescent response can be converted directly into a map of the sample surface temperature. This technique offers spatial resolution limited only by the microscope optics (about 1 micron) and time resolution limited by the speed of the camera employed. It offers the additional advantages of only requiring comparatively simple and non-specialized equipment, and giving a quantitative probe of sample temperature.

  9. In vivo synthesis of europium selenide nanoparticles and related cytotoxicity evaluation of human cells.

    Science.gov (United States)

    Kim, Eun Bee; Seo, Ji Min; Kim, Gi Wook; Lee, Sang Yup; Park, Tae Jung

    2016-12-01

    Nanotechnology strives to combine new materials for development of noble nanoparticles. As the nanoparticles exhibit unique optical, electronic, and magnetic properties depending on their composition, developing safe, cost-effective and environmentally friendly technologies for the synthesis have become an important issue. In this study, in vivo synthesis of europium selenide (EuSe) nanoparticles was performed using recombinant Escherichia coli cells expressing heavy-metal binding proteins, phytochelatin synthase and metallothionein. The formation of EuSe nanoparticles was confirmed by using UV-vis spectroscopy, spectrofluorometry, X-ray diffraction, energy dispersive X-ray and transmission electron microscopy. The synthesized EuSe nanoparticles exhibited high fluorescence intensities as well as strong magnetic properties. Furthermore, anti-cancer effect of EuSe nanoparticles against cancer cell lines was investigated. This strategy for the biogenic synthesis of nanoparticles has a great potential as bioimaging tools and drug carrying agents in biomedical fields due to its simplicity and nontoxicity. Copyright © 2016 Elsevier Inc. All rights reserved.

  10. Circularly Polarized Luminescence in Enantiopure Europium and Terbium Complexes with Modular, All-Oxygen Donor Ligands

    Science.gov (United States)

    Seitz, Michael; Do, King; Ingram, Andrew J.; Moore, Evan G.; Muller, Gilles; Raymond, Kenneth N.

    2009-01-01

    Abstract: Circulaly polarized luminescence from terbium(III) complexed and excited by chiral antenna ligands gives strong emission The modular synthesis of three new octadentate, enantiopure ligands are reported - one with the bidentate chelating unit 2-hydroxyisophthalamide (IAM) and two with 1-hydroxy-2-pyridinone (1,2-HOPO) units. A new design principle is introduced for the chiral, non-racemic hexamines which constitute the central backbones for the presented class of ligands. The terbium(III) complex of the IAM ligand, as well as the europium(III) complexes of the 1,2-HOPO ligands are synthesized and characterized by various techniques (NMR, UV, CD, luminescence spectroscopy). All species exhibit excellent stability and moderate to high luminescence efficiency (quantum yields ΦEu = 0.05–0.08 and ΦTb = 0.30–0.57) in aqueous solution at physiological pH. Special focus is put onto the properties of the complexes in regard to circularly polarized luminescence (CPL). The maximum luminescence dissymmetry factors (glum) in aqueous solution are high with |glum|max = 0.08 – 0.40. Together with the very favorable general properties (good stability, high quantum yields, long lifetimes), the presented lanthanide complexes can be considered as good candidates for analytical probes based on CPL in biologically relevant environments. PMID:19639983

  11. Complexation and molecular modeling studies of europium(III)-gallic acid-amino acid complexes.

    Science.gov (United States)

    Taha, Mohamed; Khan, Imran; Coutinho, João A P

    2016-04-01

    With many metal-based drugs extensively used today in the treatment of cancer, attention has focused on the development of new coordination compounds with antitumor activity with europium(III) complexes recently introduced as novel anticancer drugs. The aim of this work is to design new Eu(III) complexes with gallic acid, an antioxida'nt phenolic compound. Gallic acid was chosen because it shows anticancer activity without harming health cells. As antioxidant, it helps to protect human cells against oxidative damage that implicated in DNA damage, cancer, and accelerated cell aging. In this work, the formation of binary and ternary complexes of Eu(III) with gallic acid, primary ligand, and amino acids alanine, leucine, isoleucine, and tryptophan was studied by glass electrode potentiometry in aqueous solution containing 0.1M NaNO3 at (298.2 ± 0.1) K. Their overall stability constants were evaluated and the concentration distributions of the complex species in solution were calculated. The protonation constants of gallic acid and amino acids were also determined at our experimental conditions and compared with those predicted by using conductor-like screening model for realistic solvation (COSMO-RS) model. The geometries of Eu(III)-gallic acid complexes were characterized by the density functional theory (DFT). The spectroscopic UV-visible and photoluminescence measurements are carried out to confirm the formation of Eu(III)-gallic acid complexes in aqueous solutions. Copyright © 2016 Elsevier Inc. All rights reserved.

  12. Luminescent single-walled carbon nanotube-sensitized europium nanoprobes for cellular imaging

    Science.gov (United States)

    Avti, Pramod K; Sitharaman, Balaji

    2012-01-01

    Lanthanoid-based optical probes with excitation wavelengths in the ultra-violet (UV) range (300–325 nm) have been widely developed as imaging probes. Efficient cellular imaging requires that lanthanoid optical probes be excited at visible wavelengths, to avoid UV damage to cells. The efficacy of europium-catalyzed single-walled carbon nanotubes (Eu-SWCNTs), as visible nanoprobes for cellular imaging, is reported in this study. Confocal fluorescence microscopy images of breast cancer cells (SK-BR-3 and MCF-7) and normal cells (NIH 3T3), treated with Eu-SWCNT at 0.2 μg/mL concentration, showed bright red luminescence after excitation at 365 nm and 458 nm wavelengths. Cell viability analysis showed no cytotoxic effects after the incubation of cells with Eu-SWCNTs at this concentration. Eu-SWCNT uptake is via the endocytosis mechanism. Labeling efficiency, defined as the percentage of incubated cells that uptake Eu-SWCNT, was 95%–100% for all cell types. The average cellular uptake concentration was 6.68 ng Eu per cell. Intracellular localization was further corroborated by transmission electron microscopy and Raman microscopy. The results indicate that Eu-SWCNT shows potential as a novel cellular imaging probe, wherein SWCNT sensitizes Eu3+ ions to allow excitation at visible wavelengths, and stable time-resolved red emission. The ability to functionalize biomolecules on the exterior surface of Eu-SWCNT makes it an excellent candidate for targeted cellular imaging. PMID:22619533

  13. Europium(III) DOTA-derivatives having ketone donor pendant arms display dramatically slower water exchange

    Science.gov (United States)

    Green, Kayla N.; Viswanathan, Subha; Rojas-Quijano, Federico A.; Kovacs, Zoltan; Sherry, A. Dean

    2011-01-01

    A series of new 1,4,7,10-tetraazacyclododecane-derivatives having a combination of amide and ketone donor groups as side-arms were prepared and their complexes with europium(III) studied in detail by high resolution NMR spectroscopy. The chemical shift of the Eu3+-bound water resonance, the chemical exchange saturation transfer (CEST) characteristics of the complexes, and the bound water residence lifetimes (τm) were found to vary dramatically with the chemical structure of the side-arms. Substitution of ketone oxygen donor atoms for amide oxygen donor atoms resulted in an increase in residence water lifetimes (τm) and a decrease in chemical shift of the Eu3+-bound water molecule (Δω). These experimental results along with density functional theory (DFT) calculations demonstrate that introduction of weakly donating oxygen atoms in these complexes results in a much weaker ligand field, more positive charge on the Eu3+ ion and an increased water residence lifetime as expected for a dissociative mechanism. These results provide new insights into the design of paramagnetic CEST agents with even slower water exchange kinetics that will make them more efficient for in vivo imaging applications. PMID:21306137

  14. Urinary monitoring of exposure to yttrium, scandium, and europium in male Wistar rats.

    Science.gov (United States)

    Kitamura, Yasuhiro; Usuda, Kan; Shimizu, Hiroyasu; Fujimoto, Keiichi; Kono, Rei; Fujita, Aiko; Kono, Koichi

    2012-12-01

    On the assumption that rare earth elements (REEs) are nontoxic, they are being utilized as replacements of toxic heavy metals in novel technological applications. However, REEs are not entirely innocuous, and their impact on health is still uncertain. In the past decade, our laboratory has studied the urinary excretion of REEs in male Wistar rats given chlorides of europium, scandium, and yttrium solutions by one-shot intraperitoneal injection or oral dose. The present paper describes three experiments for the suitability and appropriateness of a method to use urine for biological monitoring of exposure to these REEs. The concentrations of REEs were determined in cumulative urine samples taken at 0-24 h by inductively coupled plasma atomic emission spectroscopy, showing that the urinary excretion of REEs is <2 %. Rare earth elements form colloidal conjugates in the bloodstream, which make high REEs accumulation in the reticuloendothelial system and glomeruli and low urinary excretion. The high sensitivity of inductively coupled plasma-argon emission spectrometry analytical methods, with detection limits of <2 μg/L, makes urine a comprehensive assessment tool that reflects REE exposure. The analytical method and animal experimental model described in this study will be of great importance and encourage further discussion for future studies.

  15. Europium Luminescence: Electronic Densities and Superdelocalizabilities for a Unique Adjustment of Theoretical Intensity Parameters

    Science.gov (United States)

    Dutra, José Diogo L.; Lima, Nathalia B. D.; Freire, Ricardo O.; Simas, Alfredo M.

    2015-09-01

    We advance the concept that the charge factors of the simple overlap model and the polarizabilities of Judd-Ofelt theory for the luminescence of europium complexes can be effectively and uniquely modeled by perturbation theory on the semiempirical electronic wave function of the complex. With only three adjustable constants, we introduce expressions that relate: (i) the charge factors to electronic densities, and (ii) the polarizabilities to superdelocalizabilities that we derived specifically for this purpose. The three constants are then adjusted iteratively until the calculated intensity parameters, corresponding to the 5D0→7F2 and 5D0→7F4 transitions, converge to the experimentally determined ones. This adjustment yields a single unique set of only three constants per complex and semiempirical model used. From these constants, we then define a binary outcome acceptance attribute for the adjustment, and show that when the adjustment is acceptable, the predicted geometry is, in average, closer to the experimental one. An important consequence is that the terms of the intensity parameters related to dynamic coupling and electric dipole mechanisms will be unique. Hence, the important energy transfer rates will also be unique, leading to a single predicted intensity parameter for the 5D0→7F6 transition.

  16. Structural and spectroscopic analyses of europium doped yttrium oxyfluoride powders prepared by combustion synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Rakov, Nikifor [PG-Ciência dos Materiais, Universidade Federal do Vale do São Francisco, 48902-300 Juazeiro, BA (Brazil); Guimarães, R. B.; Maciel, Glauco S. [Instituto de Física, Universidade Federal Fluminense, 24210-346 Niterói, RJ (Brazil); Lozano B, W. [Departamento de Física, Universidade Federal de Pernambuco, 50670-901 Recife, PE (Brazil)

    2013-07-28

    A facile widely spread technique employed to produce low-cost high-yield oxide powders, combustion synthesis, was used to prepare yttrium oxyfluoride crystalline ceramic powders. The structure of the powders was analyzed by X-ray powder diffraction and Rietveld refinement. Samples heat treated at 700 °C had a predominance of vernier orthorhombic Y{sub 6}O{sub 5}F{sub 8} phase, while samples heat treated at 800 °C crystallized in stoichiometric rhombohedral YOF phase. The samples were doped with luminescent europium trivalent ions (Eu{sup 3+}) in different concentrations (1–15 wt.%) and Judd-Ofelt theory was used to probe the distortion from the inversion symmetry of the local crystal field and the degree of covalency between the rare-earth ion and the surrounding ligands. The luminescence lifetime was measured and the luminescence quantum efficiency (LQE) was estimated. We observed that Eu{sup 3+}:Y{sub 6}O{sub 5}F{sub 8} samples presented higher LQE in spite of the larger local crystal field anisotropy found for Eu{sup 3+}:YOF samples.

  17. New ternary tantalum borides containing boron dumbbells: Experimental and theoretical studies of Ta{sub 2}OsB{sub 2} and TaRuB

    Energy Technology Data Exchange (ETDEWEB)

    Mbarki, Mohammed; Touzani, Rachid St.; Rehorn, Christian W.G.; Gladisch, Fabian C. [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Fokwa, Boniface P.T., E-mail: bfokwa@ucr.edu [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Department of Chemistry, University of California Riverside (UCR), Riverside, CA 92521 (United States)

    2016-10-15

    The new ternary transition metal-rich borides Ta{sub 2}OsB{sub 2} and TaRuB have been successfully synthesized by arc-melting the elements in a water-cooled crucible under an argon atmosphere. The crystal structures of both compounds were solved by single-crystal X-ray diffraction and their metal compositions were confirmed by EDX analysis. It was found that Ta{sub 2}OsB{sub 2} and TaRuB crystallize in the tetragonal Nb{sub 2}OsB{sub 2} (space group P4/mnc, no. 128) and the orthorhombic NbRuB (space group Pmma, no. 51) structure types with lattice parameters a=5.878(2) Å, c=6.857(2) Å and a=10.806(2) Å, b=3.196(1) Å, c=6.312(2) Å, respectively. Furthermore, crystallographic, electronic and bonding characteristics have been studied by density functional theory (DFT). Electronic structure relaxation has confirmed the crystallographic parameters while COHP bonding analysis indicates that B{sub 2}-dummbells are the strongest bonds in both compounds. Moreover, the formation of osmium dumbbells in Ta{sub 2}OsB{sub 2} through a Peierls distortion along the c-axis, is found to be the origin of superstructure formation. Magnetic susceptibility measurements reveal that the two phases are Pauli paramagnets, thus confirming the theoretical DOS prediction of metallic character. Also hints of superconductivity are found in the two phases, however lack of single phase samples has prevented confirmation. Furthermore, the thermodynamic stability of the two modifications of AMB (A=Nb, Ta; M =Ru, Os) are studied using DFT, as new possible phases containing either B{sub 4}- or B{sub 2}-units are predicted, the former being the most thermodynamically stable modification. - Graphical abstract: The two new ternary tantalum borides, Ta{sub 2}OsB{sub 2} and TaRuB, have been discovered. Their crystal structures contain boron dumbbells, which are the strongest bonds. Peirls distortion is found responsible for Os{sub 2}-dumbbells formation in Ta{sub 2}OsB{sub 2}. Ta{sub 2}OsB{sub 2} and

  18. Synthesis, photophysics, electrochemistry, thermal stability and electroluminescent performances of a new europium complex with bis(β-diketone) ligand containing carbazole group.

    Science.gov (United States)

    Liu, Jian; Liang, Quan-Bin; Wu, Hong-Bin

    2017-05-01

    We synthesized a new europium complex [Eu(ecbpd)3 (Phen)] with bis(β-diketone) ligand containing a carbazole group, in which ecbpd and Phen are dehydro-3,3'-(9-ethyl-9H-carbazole-3,6-diyl)bis(1-phenylpropane-1,3-dione) and 1,10-phenanthroline, respectively. Its UV/vis and photoluminescent spectra, quantum yield, luminescence lifetime, electrochemistry, thermal stability and electroluminescent performances were studied. This europium complex showed low efficiency luminescence, which is probably due to the mismatching energy levels of its ligand and Eu3+ , as well as the double Eu3+ core resonance. Copyright © 2016 John Wiley & Sons, Ltd.

  19. Europium (III) PVC membrane sensor based on N-pyridine-2-carboxamido-8-aminoquinoline as a sensing material

    Energy Technology Data Exchange (ETDEWEB)

    Zamani, Hassan Ali, E-mail: haszamani@yahoo.com [Department of Applied Chemistry, Quchan branch, Islamic Azad University, Quchan (Iran, Islamic Republic of); Kamjoo, Rahman [Department of Applied Chemistry, Quchan branch, Islamic Azad University, Quchan (Iran, Islamic Republic of); Mohammadhosseini, Majid [Department of Chemistry, Faculty of Basic Sciences, Shahrood Branch, Islamic Azad University, Shahrood (Iran, Islamic Republic of); Zaferoni, Mojdeh; Rafati, Zynab [Department of Applied Chemistry, Quchan branch, Islamic Azad University, Quchan (Iran, Islamic Republic of); Ganjali, Mohammad Reza [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Endocrinology and Metabolism Research Center, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Faridbod, Farnoush [Endocrinology and Metabolism Research Center, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Meghdadi, Soraia [Department of Chemistry, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of)

    2012-04-01

    Conductometric study in acetonitrile solution shows the selectivity of PCQ toward europium ion. Therefore, a new europium PVC membrane electrode was prepared based on N-pyridine-2-carboxamido-8-aminoquinoline (PCQ) as an ion carrier. The electrode has a wide concentration range from 1.0 Multiplication-Sign 10{sup -2} and 1.0 Multiplication-Sign 10{sup -6} mol L{sup -1}, Nernstian slope of 19.8 {+-} 0.3 mV per decade and a detection limit of 6.4 Multiplication-Sign 10{sup -7} mol L{sup -1}. The potentiometric response is pH independent in the range of 2.4-7.4. The proposed sensor has a relatively fast response time less than 10 s and it can be used for at least 2 months without any considerable divergence in its potentials. The proposed electrode revealed good selectivity toward europium ion in comparison with variety of other metal ions. The practical utility of the electrodes has been demonstrated by their use as indicator electrodes in the potentiometric titration of Eu{sup 3+} ions with EDTA and for determination of Eu{sup 3+} ion concentration in mixtures of two and three different ions. - Highlights: Black-Right-Pointing-Pointer A new ion carrier is introduced to preparation of a selective sensor for Eu{sup 3+} ions. Black-Right-Pointing-Pointer This technique is very simple and it's not necessary to use sophisticated equipment. Black-Right-Pointing-Pointer The novelty of this work is the high affinity of the ionophore toward the Eu{sup 3+} ions. Black-Right-Pointing-Pointer The sensor is superior to the formerly reported Eu{sup 3+} sensors in terms of selectivity.

  20. A novel tridentate bis(phosphinic acid)phosphine oxide based europium(III)-selective Nafion membrane luminescent sensor.

    Science.gov (United States)

    Sainz-Gonzalo, F J; Popovici, C; Casimiro, M; Raya-Barón, A; López-Ortiz, F; Fernández, I; Fernández-Sánchez, J F; Fernández-Gutiérrez, A

    2013-10-21

    A new europium(III) membrane luminescent sensor based on a new tridentate bis(phosphinic acid)phosphine oxide (3) system has been developed. The synthesis of this new ligand is described and its full characterization by NMR, IR and elemental analyses is provided. The luminescent complex formed between europium(III) chloride and ligand 3 was evaluated in solution, observing that its spectroscopic and chemical characteristics are excellent for measuring in polymer inclusion membranes. Included in a Nafion membrane, all the parameters (ligand and ionic additives) that can affect the sensitivity and selectivity of the sensing membrane as well as the instrumental conditions were carefully optimized. The best luminescence signal (λexc = 229.06 nm and λem = 616.02 nm) was exhibited by the sensing film having a Nafion : ligand composition of 262.3 : 0.6 mg mL(-1). The membrane sensor showed a short response time (t95 = 5.0 ± 0.2 min) and an optimum working pH of 5.0 (25 mM acetate buffer solution). The membrane sensor manifested a good selectivity toward europium(III) ions with respect to other trivalent metals (iron, chromium and aluminium) and lanthanide(III) ions (lanthanum, samarium, terbium and ytterbium), although a small positive interference of terbium(III) ions was observed. It provided a linear range from 1.9 × 10(-8) to 5.0 × 10(-6) M with a very low detection limit (5.8 × 10(-9) M) and sensitivity (8.57 × 10(-7) a.u. per M). The applicability of this sensing film has been demonstrated by analyzing different kinds of spiked water samples obtaining recovery percentages of 95-97%.

  1. A Responsive Europium(III) Chelate that Provides a Direct Readout of pH by MRI

    Science.gov (United States)

    Wu, Yunkou; Soesbe, Todd C.; Kiefer, Garry E.; Zhao, Piyu; Sherry, A. Dean

    2010-01-01

    A europium(III) DO3A-tris(amide) complex is reported for imaging pH by MRI using ratiometric CEST principles. Deprotonation of a single phenolic proton between pH 6 and 7.6 results in an ~5 ppm shift in the water exchange CEST peak that is easily detected by MRI. Collection of two CEST images at two slightly different activation frequencies provides a direct readout of solution pH without the need of a concentration marker. PMID:20853833

  2. Effect of Heat Treatment on Borides Precipitation and Mechanical Properties of CoCrFeNiAl1.8Cu0.7B0.3Si0.1 High-Entropy Alloy Prepared by Arc-Melting and Laser-Cladding

    Science.gov (United States)

    Zhang, H.; Tang, H.; He, Y. Z.; Zhang, J. L.; Li, W. H.; Guo, S.

    2017-11-01

    Effects of heat treatment on borides precipitation and mechanical properties of arc-melted and laser-cladded CoCrNiFeAl1.8Cu0.7B0.3Si0.1 high-entropy alloys were comparatively studied. The arc-melted alloy contains lots of long strip borides distributed in the body-centered cubic phase, with a hardness about 643 HV0.5. Laser-cladding can effectively inhibit the boride precipitation and the laser-cladded alloy is mainly composed of a simple bcc solid solution, with a high hardness about 769 HV0.5, indicating the strengthening effect by interstitial boron atoms is greater than the strengthening by borides precipitation. Heat treatments between 800°C and 1200°C can simultaneously improve the hardness and fracture toughness of arc-melted alloys, owing to the boride spheroidization, dissolution, re-precipitation, and hence the increased boron solubility and nano-precipitation in the bcc solid solution. By contrast, the hardness of laser-cladded alloys reduce after heat treatments in the same temperature range, due to the decreased boron solubility in the matrix.

  3. Spectroscopic properties and luminescence behaviour of europium doped lithium borate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Anjaiah, J., E-mail: anjaiah.juluru@gmail.com [Department of Physics, The University of Dodoma, Tanzania, East Africa (Tanzania, United Republic of); Department of Physics, Geethanjali College of Engineering and Technology, Keesara, RR Dist., Hyderabad 501 301 (India); Laxmikanth, C. [Department of Physics, The University of Dodoma, Tanzania, East Africa (Tanzania, United Republic of); Veeraiah, N. [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar, Guntur 522 510, AP. (India)

    2014-12-01

    Li{sub 2}O–MO–B{sub 2}O{sub 3} (MO=ZnO, CaO and CdO) glasses doped with europium are prepared by using the melt quenching technique to study their absorption and luminescence properties to understand their lasing potentialities. The XRD pattern of the glasses confirmed the amorphous nature and the IR spectra reveal the presence of BO{sub 3} and BO{sub 4} units in the glass network. Judd–Ofelt intensity parameters Ω{sub λ} (λ=2, 4, 6) are evaluated from the intensities of various absorption bands of optical absorption spectra. The J–O parameters have been used to calculate transition probabilities (A), lifetime (τ{sub R}), branching ratios (β{sub R}) and stimulated emission cross-section (σ{sub P}) for the {sup 5}D{sub 0}→{sup 7}F{sub J} (J=1–4) transitions of the Eu{sup 3+} ions. The decay from the {sup 5}D{sub 0} level of Eu{sup 3+} ions in these glasses has been measured and analysed. Branching ratios and stimulated emission cross-sections measured for all these glasses show that the {sup 5}D{sub 0}→{sup 7}F{sub 1} transition under investigation has the potential for laser applications. The high stimulated emission cross-section and branching ratios from the present glasses suggests their potential for infra red lasers. The study of the thermoluminescence is also carried out and the data suggests that the CdBEu glass is suitable for thermoluminescence emission output among the three Eu{sup 3+} doped glasses.

  4. Size-dependent cytotoxicity of europium doped NaYF{sub 4} nanoparticles in endothelial cells

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Shizhu; Zhang, Cuimiao; Jia, Guang; Duan, Jianlei; Wang, Shuxiang, E-mail: wsx@hbu.edu.cn; Zhang, Jinchao, E-mail: jczhang6970@163.com

    2014-10-01

    Lanthanide-doped sodium yttrium fluoride (NaYF{sub 4}) nanoparticles exhibit novel optical properties which make them be widely used in various fields. The extensive applications increase the chance of human exposure to these nanoparticles and thus raise deep concerns regarding their riskiness. In the present study, we have synthesized europium doped NaYF{sub 4} (NaYF{sub 4}:Eu{sup 3+}) nanoparticles with three diameters and used endothelial cells (ECs) as a cell model to explore the potential toxic effect. The cell viability, cytomembrane integrity, cellular uptake, intracellular localization, intracellular reactive oxygen species (ROS), mitochondrial membrane potential (MMP), apoptosis detection, caspase-3 activity and expression of inflammatory gene were studied. The results indicated that these nanoparticles could be uptaken into ECs and decrease the cell viability, induce the intracellular lactate dehydrogenase (LDH) release, increase the ROS level, and decrease the cell MMP in a size-dependent manner. Besides that, the cells were suffered to apoptosis with the caspase-3 activation, and the inflammation specific gene expressions (ICAM1 and VCAM1) were also increased. Our results suggest that the damage pathway may be related to the ROS generation and mitochondrial damage. The results provide novel evidence to elucidate their toxicity mechanisms and may be helpful for more rational applications of these compounds in the future. - Highlights: • NaYF{sub 4}:Eu{sup 3+} nanoparticles with three diameters have been synthesized. • NaYF{sub 4}:Eu{sup 3+} nanoparticles could be uptaken by endothelial cells (ECs). • NaYF{sub 4}:Eu{sup 3+} nanoparticles show a significant cytotoxicity on ECs. • The size of NaYF{sub 4}:Eu{sup 3+} nanoparticles may be important to their toxicology effect.

  5. Two-dimensional high spatial-resolution dosimeter using europium doped potassium chloride: a feasibility study

    Science.gov (United States)

    Li, H. Harold; Driewer, Joseph P.; Han, Zhaohui; Low, Daniel A.; Yang, Deshan; Xiao, Zhiyan

    2014-01-01

    Recent research has shown that KCl:Eu2+ has great potential for use in megavoltage radiation therapy dosimetry because this material exhibits excellent storage performance and is reusable due to strong radiation hardness. This work reports the authors’ attempts to fabricate 2D KCl:Eu2+ storage phosphor films (SPFs) using both a physical vapor deposition (PVD) method and a tape casting method. X ray diffraction analysis showed that a 10 µm thick PVD sample was composed of highly crystalline KCl. No additional phases were observed, suggesting that the europium activator had completed been incorporated into the KCl matrix. Photostimulated luminescence and photoluminescence spectra suggested that F (Cl-) centers were the electron storage centers post×ray irradiation and that Eu2+ cations acted as luminescence centers in the photostimulation process. The 150-µm thick casted KCl:Eu2+ SPF showed sub-millimeter spatial resolution. Monte Carlo simulations further demonstrated that the admixture of 20% KCl:Eu2+ and 80% low Z polymer binder exhibited almost no energy dependence in a 6 MV beam. KCl:Eu2+ pellet samples showed a large dynamic range from 0.01 cGy to 60 Gy dose-to-water, and saturated at approximately 500 Gy as a result of KCl’s intrinsic high radiation hardness. Taken together, this work provides strong evidence that KCl:Eu2+ based SPF with associated readout apparatus could result in a novel electronic film system that has all the desirable features associated with classic radiographic film and, importantly, water equivalence and the capability of permanent identification of each detector. PMID:24651448

  6. A Novel Europium Chelate Coated Nanosphere for Time-Resolved Fluorescence Immunoassay

    Science.gov (United States)

    Shen, Yifeng; Xu, Shaohan; He, Donghua

    2015-01-01

    A novel europium ligand 2, 2’, 2’’, 2’’’-(4, 7-diphenyl-1, 10-phenanthroline-2, 9-diyl) bis (methylene) bis (azanetriyl) tetra acetic acid (BC-EDTA) was synthesized and characterized. It shows an emission spectrum peak at 610 nm when it is excited at 360 nm, with a large Stock shift (250 nm). It is covalently coated on the surface of a bare silica nanosphere containi free amino groups, using 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride and N-Hydroxysuccinimide. We also observed an interesting phenomenon that when BC-EDTA is labeled with a silica nanosphere, the chelate shows different excitation spectrum peaks of about 295 nm. We speculate that the carboxyl has a significant influence on its excitation spectrum. The BC-EDTA/Eu3+coated nanosphere could be used as a fluorescent probe for time-resolved fluorescence immunoassay. We labeled the antibody with the fluorescent nanosphere to develop a nanosphere based hepatitis B surface antigen as a time-resolved fluorescence immunoassay reagent, which is very easy to operate and eliminates potential contamination of Eu3+ contained in the environment. The analytical and functional sensitivities are 0.0037 μg/L and 0.08 μg/L (S/N≥2.0) respectively. The detection range is 0.08-166.67 μg/L, which is much wider than that of ELISA (0.2-5μg/L). It is comparable to the commercial dissociation-enhanced lanthanide fluoro-immunoassay system (DELFIA) reagents (0.2-145μg/L). We propose that it can fulfill clinical applications. PMID:26056826

  7. A Novel Europium Chelate Coated Nanosphere for Time-Resolved Fluorescence Immunoassay.

    Directory of Open Access Journals (Sweden)

    Yifeng Shen

    Full Text Available A novel europium ligand 2,2',2'',2'''-(4,7-diphenyl-1,10-phenanthroline-2,9-diyl bis (methylene bis (azanetriyl tetra acetic acid (BC-EDTA was synthesized and characterized. It shows an emission spectrum peak at 610 nm when it is excited at 360 nm, with a large Stock shift (250 nm. It is covalently coated on the surface of a bare silica nanosphere containi free amino groups, using 1-ethyl-3-(3-dimethylaminopropyl carbodiimide hydrochloride and N-Hydroxysuccinimide. We also observed an interesting phenomenon that when BC-EDTA is labeled with a silica nanosphere, the chelate shows different excitation spectrum peaks of about 295 nm. We speculate that the carboxyl has a significant influence on its excitation spectrum. The BC-EDTA/Eu3+coated nanosphere could be used as a fluorescent probe for time-resolved fluorescence immunoassay. We labeled the antibody with the fluorescent nanosphere to develop a nanosphere based hepatitis B surface antigen as a time-resolved fluorescence immunoassay reagent, which is very easy to operate and eliminates potential contamination of Eu3+ contained in the environment. The analytical and functional sensitivities are 0.0037 μg/L and 0.08 μg/L (S/N≥2.0 respectively. The detection range is 0.08-166.67 μg/L, which is much wider than that of ELISA (0.2-5 μg/L. It is comparable to the commercial dissociation-enhanced lanthanide fluoro-immunoassay system (DELFIA reagents (0.2-145 μg/L. We propose that it can fulfill clinical applications.

  8. TOF SIMS analysis and generation of white photoluminescence from strontium silicate codoped with europium and terbium

    Energy Technology Data Exchange (ETDEWEB)

    Tshabalala, Modiehi A.; Swart, Hendrik C.; Ntwaeaborwa, Odireleng M., E-mail: ntwaeab@ufs.ac.za [Department of Physics, University of the Free State, P.O Box 339, Bloemfontein 9300 South Africa (South Africa)

    2014-03-15

    White light emitting terbium (Tb{sup 3+}) and europium (Eu{sup 3+}) codoped strontium silicate (Sr{sub 2}SiO{sub 4}) phosphors were prepared by a solid state reaction process. The structure, particle morphology, chemical composition, ion distribution, photoluminescence (PL), and decay characteristics of the phosphors were analyzed by x-ray diffraction (XRD), scanning electron microscopy (SEM), time-of-flight secondary ion mass spectrometry (TOF-SIMS), and PL spectroscopy, respectively. The XRD data showed that our Sr{sub 2}SiO{sub 4} composed of two phases, namely, β-Sr{sub 2}SiO{sub 4} and α′-Sr{sub 2}SiO{sub 4}, and the α′-Sr{sub 2}SiO{sub 4} phase was more prominent than the β-Sr{sub 2}SiO{sub 4} phase. The SEM micrographs showed that the particles were agglomerated together and they did not have definite shapes. All ions (i.e., negative and positive) present in our materials were identified by TOF-SIMS. In addition, the chemical imaging performed with the TOF-SIMS demonstrated how the individual ions including the dopants (Eu{sup 3+} and Tb{sup 3+}) were distributed in the host lattice. White photoluminescence was observed when the Sr{sub 2}SiO{sub 4}:Tb{sup 3+}, Eu{sup 3+} phosphor was excited at 239 nm using a monochromatized xenon lamp as the excitation source. The phosphor exhibited fast decay lifetimes implying that it is not a good candidate for long afterglow applications.

  9. Thermoluminescence of europium-doped zinc oxide exposed to beta particle irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Iriqui R, J. L.; Cruz V, C. [Universidad de Sonora, Departamento de Investigacion en Polimeros y Materiales, Apdo. Postal 130, 83000 Hermosillo, Sonora (Mexico); Bernal, R. [Universidad de Sonora, Departamento de Investigacion en Fisica, Apdo. Postal 5-088, 83000 Hermosillo, Sonora (Mexico); Castano, V. M., E-mail: jorgeiriqui@gimmunison.com [UNAM, Instituto de Fisica, Centro de Fisica Aplicada y Tecnologia Avanzada, Apdo. Postal 1-1010, 76000 Queretaro, Qro. (Mexico)

    2015-10-15

    Full text: Zn O is a promising material for a range of optoelectronics applications, due to its direct wide band gap (E{sub g} ∼3.3 eV at 300 K) and large exciton binding energy (60 MeV). Its applications include UV light emitters, varistors, surface acoustic wave devices, piezoelectric transducers, and chemical and gas sensing. Rare-earth activation of phosphors has long been seen as an effective process since coupling energy into the rare-earth-ion site, either by ionization, charge exchange or a resonance energy process, results in light production. It is reported that Europium modifies the response thermoluminescence (Tl) for pure zinc oxide, when is irradiated with X-ray, created a peak at 365 degrees C. In this work, Zn O:Eu phosphors were synthesized by a chemical method. Some samples were exposed to beta particle irradiation for doses ranging from 1 up to 100 Gy. Tl response as a function of dose is linear throughout the studied dose range. The glow curve exhibits three maxima, centered at 176, 279 and 340 degrees C. The reusability studies obtained after ten repeated cycles of annealing irradiation readout for the Zn O:Eu shows that the variation in the Tl response is ten percent and tends to stabilization. The results indicate that these new Zn O:Eu phosphors are promising detectors and dosimeters for beta radiation. The structural and morphological characterization was carried out by X-ray diffraction and scanning electron microscopy, respectively. (Author)

  10. Synthesis and characterization of barium titanate, doped with europium and neodymium; Sintese e caracterizacao de titanato de bario, dopados com europio e neodimio

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, Fernanda L.C.; Cabral, Alciney M.; Silva, Ademir O.; Oliveiro, Joao B.L., E-mail: nanda_louise@yahoo.com.br [Universidade Federal do Rio Grande do Norte (UFRN), Natal (Brazil). Instituto de Quimica

    2013-07-01

    This work aims at synthesize and characterize mixed oxides in Barium Titanium matrix in doping with Neodymium and Europium analyzing thermogravimetric curves, characteristic bands at infrared region of the polymer complex, which are intermediates to mixed oxides, and identify the formation thereof, and the crystallinity using XRD analysis.

  11. Stability constants of the Europium complexes with the chloride ions; Constantes de estabilidad de los complejos del europio con los iones cloruro

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez R, M.; Solache R, M.; Rojas H, A. [Instituto Nacional de Investigaciones Nucleares, Departamento de Quimica, A.P. 18-1027, C.P. 11801 Mexico D.F. (Mexico)

    2000-07-01

    The stability constants of lanthanides complexes with chloride ions which were determined at the same ionic force but in different media, are significantly different. It does not exist a systematic study over these stability constants. The purpose of this work is to determine the stability constants of the europium complexes with chloride ions at 303 K, by the solvents extraction method. (Author)

  12. LA-ICP-MS Allows Quantitative Microscopy of Europium-Doped Iron Oxide Nanoparticles and is a Possible Alternative to Ambiguous Prussian Blue Iron Staining.

    Science.gov (United States)

    Scharlach, Constantin; Müller, Larissa; Wagner, Susanne; Kobayashi, Yuske; Kratz, Harald; Ebert, Monika; Jakubowski, Norbert; Schellenberger, Eyk

    2016-05-01

    The development of iron oxide nanoparticles for biomedical applications requires accurate histological evaluation. Prussian blue iron staining is widely used but may be unspecific when tissues contain substantial endogenous iron. Here we tested whether microscopy by laser ablation coupled to inductively coupled plasma mass spectrometry (LA-ICP-MS) is sensitive enough to analyze accumulation of very small iron oxide particles (VSOP) doped with europium in tissue sections. For synthesis of VSOP, a fraction of Fe3+ (5 wt%) was replaced by Eu3+, resulting in particles with 0.66 mol% europium relative to iron (Eu-VSOP) but with otherwise similar properties as VSOP. Eu-VSOP or VSOP was intravenously injected into ApoE-/- mice on Western cholesterol diet and accumulated in atherosclerotic plaques of these animals. Prussian blue staining was positive for ApoE-/- mice with particle injection but also for controls. LA-ICP-MS microscopy resulted in sensitive and specific detection of the europium of Eu-VSOP in liver and atherosclerotic plaques. Furthermore, calibration with Eu-VSOP allowed calculation of iron and particle concentrations in tissue sections. The combination of europium-doped iron oxide particles and LA-ICP-MS microscopy provides a new tool for specific and quantitative analysis of particle distribution at the tissue level and allows correlation with other elements such as endogenous iron.

  13. Novel Time-Resolved Fluorescence Europium Nanoparticle Immunoassay for Detection of Human Immunodeficiency Virus-1 Group O Viruses Using Microplate and Microchip Platforms.

    Science.gov (United States)

    Haleyur Giri Setty, Mohan Kumar; Liu, Jikun; Mahtani, Prerna; Zhang, Panhe; Du, Bingchen; Ragupathy, Viswanath; Devadas, Krishnakumar; Hewlett, Indira K

    2016-06-01

    Accurate detection and quantification of HIV-1 group O viruses have been challenging for currently available HIV assays. We have developed a novel time-resolved fluorescence (TRF) europium nanoparticle immunoassay for HIV-1 group O detection using a conventional microplate enzyme-linked immunosorbent assay (ELISA) and a microchip platform. We screened several antibodies for optimal reactivity with several HIV-1 group O strains and identified antibodies that can detect all the strains of HIV-1 group O that were available for testing. The antibodies were used to develop a conventional ELISA format assay and an in-house developed europium nanoparticle-based assay for sensitivity. The method was evaluated on both microwell plate and microchip platforms. We identified two specific and sensitive antibodies among the six we screened. The antibodies, C65691 and ANT-152, were able to quantify 15 and detect all 17 group O viruses, respectively, as they were broadly cross-reactive with all HIV-1 group O strains and yielded better signals compared with other antibodies. We have developed a sensitive assay that reflects the actual viral load in group O samples by using an appropriate combination of p24 antibodies that enhance group O detection and a highly sensitive TRF-based europium nanoparticle for detection. The combination of ANT-152 and C65690M in the ratio 3:1 was able to give significantly higher signals in our europium-based assay compared with using any single antibody.

  14. Lanthanide-to-lanthanide energy-transfer processes operating in discrete polynuclear complexes: can trivalent europium be used as a local structural probe?

    Science.gov (United States)

    Zaïm, Amir; Eliseeva, Svetlana V; Guénée, Laure; Nozary, Homayoun; Petoud, Stéphane; Piguet, Claude

    2014-09-15

    This work, based on the synthesis and analysis of chemical compounds, describes a kinetic approach for identifying intramolecular intermetallic energy-transfer processes operating in discrete polynuclear lanthanide complexes, with a special emphasis on europium-containing entities. When all coordination sites are identical in a (supra)molecular complex, only heterometallic communications are experimentally accessible and a Tb → Eu energy transfer could be evidenced in [TbEu(L5)(hfac)6] (hfac = hexafluoroacetylacetonate), in which the intermetallic separation amounts to 12.6 Å. In the presence of different coordination sites, as found in the trinuclear complex [Eu3(L2)(hfac)9], homometallic communication can be induced by selective laser excitation and monitored with the help of high-resolution emission spectroscopy. The narrow and non-degenerated character of the Eu((5)D0 ↔ (7)F0) transition excludes significant spectral overlap between donor and acceptor europium cations. Intramolecular energy-transfer processes in discrete polynuclear europium complexes are therefore limited to short distances, in agreement with the Fermi golden rule and with the kinetic data collected for [Eu3(L2)(hfac)9] in the solid state and in solution. Consequently, trivalent europium can be considered as a valuable local structural probe in discrete polynuclear complexes displaying intermetallic separation in the sub-nanometric domain, a useful property for probing lanthanido-polymers. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Optical isomers of N,N′-bis(1-phenylethyl)-2,6-pyridinedicarboxamide coordinated to europium(III) ions as reliable circularly polarized luminescence calibration standards†

    Science.gov (United States)

    Bonsall, Steven D.; Houcheime, Mona; Straus, Daniel A.; Muller, Gilles

    2009-01-01

    The synthesis of two optical isomers of N,N′-bis(1-phenylethyl)-2,6-pyridinedicarboxamide and the constant circularly polarized luminescence (CPL) activity of their acetonitrile trivalent europium complex solutions over a long period of time open new perspectives for performing accurate routine CPL calibration tests at low cost. PMID:17728891

  16. Photoluminescence behavior of europium (III) complexes containing 1-(4-tert-butylphenyl)-3-(2-naphthyl)-propane-1,3-dione ligand.

    Science.gov (United States)

    Wang, Dunjia; Zheng, Chunyang; Fan, Ling; Hu, Yanjun; Zheng, Jing

    2014-01-03

    Three novel europium complexes with 1-(4-tert-butylphenyl)-3-(2-naphthyl)-propane-1,3-dione (TNPD) and 2,2-dipyridine (Bipy) or 1,10-phenan-throline (Phen) were synthesized and confirmed by FT-IR, (1)H NMR, UV-vis absorption and elemental analysis. Photoluminescence behavior of complexes Eu(TNPD)3, Eu(TNPD)3·Bipy and Eu(TNPD)3·Phen were investigated in detail. Their emission spectra exhibited the characteristic emission bands that arise from the (5)D0→(7)FJ (J=0-4) transitions of the europium ion in solid state. Meanwhile, the results of their lifetime decay curves indicated that only one chemical environment existed around the europium ion. The intrinsic luminescence quantum efficiency (η) and the experimental intensity parameters (Ωt) of europium complexes were determined according to the emission spectra and luminescence decay curves in solid state. The complex Eu(TNPD)3·Phen showed much longer lifetime (τ) and higher luminescence quantum efficiency (η) than complexes Eu(TNPD)3 and Eu(TNPD)3·Bipy. Copyright © 2013 Elsevier B.V. All rights reserved.

  17. Synthesis, crystal structure and photophysical properties of europium(III) and terbium(III) complexes with pyridine-2,6-dicarboxamide

    NARCIS (Netherlands)

    Tanase, S.; Gallego, P.M.; Gelder, R. de; Fu, W.T.

    2007-01-01

    The reactions of pyridine-2,6-dicarboxamide with europium(III) and terbium(III) triflates led to the formation of mononuclear complexes of formula [Ln(pcam)(3)](CF3SO3)(3) (Ln = Eu 1, Tb 2; pcam stands for pyridine-2,6-dicarboxamide). From single-crystal X-ray diffraction analysis, the complexes

  18. Structural investigation and photoluminescent properties of gadolinium(III), europium(III) and terbium(III) 3-mercaptopropionate complexes.

    Science.gov (United States)

    Souza, E R; Mazali, I O; Sigoli, F A

    2014-01-01

    This work reports on the synthesis, crystallographic determination and spectroscopic characterization of gadolinium(III), terbium(III) and europium(III) 3-mercaptopropionate complexes, aqua-tris(3-mercaptopropionate)lanthanide(III)--[Ln(mpa)3(H2O)]. The Judd-Ofelt intensity parameters were experimentally determined from emission spectrum of the [Eu(mpa)3(H2O)]complex and they were also calculated from crystallographic data. The complexes are coordination polymers, where the units of each complex are linked together by carboxylate groups leading to an unidimensional and parallel chains that by chemical interactions form a tridimensional framework. The emission spectrum profile of the [Eu(mpa)3(H2O)] complex is discussed based on point symmetry of the europium(III) ion, that explains the bands splitting observed in its emission spectrum. Photoluminescent analysis of the [Gd(mpa)3(H2O)] complex show no efficient ligand excitation but an intense charge transfer band. The excitation spectra of the [Eu(mpa)3(H2O)] and [Tb(mpa)3(H2O)] complexes do not show evidence of energy transfer from the ligand to the excited levels of these trivalent ions. Therefore the emission bands are originated only by direct f-f intraconfigurational excitation of the lantanide(III) ions.

  19. Simple preparation of fluorescent composite films based on cerium and europium doped LaF3 nanoparticles

    Science.gov (United States)

    Secco, Henrique de L.; Ferreira, Fabio F.; Péres, Laura O.

    2018-03-01

    The combination of materials to form hybrids with unique properties, different from those of the isolated components, is a strategy used to prepare functional materials with improved properties aiming to allow their application in specific fields. The doping of lanthanum fluoride with other rare earth elements is used to obtain luminescent particles, which may be useful to the manufacturing of electronic devices' displays and biological markers, for instance. The application of the powder of nanoparticles has limitations in some fields; to overcome this, the powder may be incorporated in a suitable polymeric matrix. In this work, lanthanum fluoride nanoparticles, undoped and doped with cerium and europium, were synthesized through the co-precipitation method in aqueous solution. Aiming the formation of solid state films, composites of nanoparticles in an elastomeric matrix, the nitrile rubber (NBR), were prepared. The flexibility and the transparency of the matrix in the regions of interest are advantages for the application of the luminescent composites. The composites were applied as films using the casting and the spin coating techniques and luminescent materials were obtained in the samples doped with europium and cerium. Scanning electron microscopy images showed an adequate dispersion of the particles in the matrix in both film formation techniques. Aggregates of the particles were detected in the samples which may affect the uniformity of the emission of the composites.

  20. A microwave-assisted solution combustion synthesis to produce europium-doped calcium phosphate nanowhiskers for bioimaging applications.

    Science.gov (United States)

    Wagner, Darcy E; Eisenmann, Kathryn M; Nestor-Kalinoski, Andrea L; Bhaduri, Sarit B

    2013-09-01

    Biocompatible nanoparticles possessing fluorescent properties offer attractive possibilities for multifunctional bioimaging and/or drug and gene delivery applications. Many of the limitations with current imaging systems center on the properties of the optical probes in relation to equipment technical capabilities. Here we introduce a novel high aspect ratio and highly crystalline europium-doped calcium phosphate nanowhisker produced using a simple microwave-assisted solution combustion synthesis method for use as a multifunctional bioimaging probe. X-ray diffraction confirmed the material phase as europium-doped hydroxyapatite. Fluorescence emission and excitation spectra and their corresponding peaks were identified using spectrofluorimetry and validated with fluorescence, confocal and multiphoton microscopy. The nanowhiskers were found to exhibit red and far red wavelength fluorescence under ultraviolet excitation with an optimal peak emission of 696 nm achieved with a 350 nm excitation. Relatively narrow emission bands were observed, which may permit their use in multicolor imaging applications. Confocal and multiphoton microscopy confirmed that the nanoparticles provide sufficient intensity to be utilized in imaging applications. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  1. Europium nanoparticle-based simple to perform dry-reagent immunoassay for the detection of hepatitis B surface antigen.

    Science.gov (United States)

    Talha, Sheikh M; Salminen, Teppo; Juntunen, Etvi; Spangar, Anni; Gurramkonda, Chandrasekhar; Vuorinen, Tytti; Khanna, Navin; Pettersson, Kim

    2016-03-01

    Hepatitis B infection, caused by hepatitis B virus (HBV), presents a huge global health burden. Serological diagnosis of HBV mainly relies on the detection of hepatitis B surface antigen (HBsAg). Although there are high sensitivity commercial HBsAg enzyme immunoassays (EIAs) available, many low-resource laboratories lacking trained technicians continue to use rapid point-of-care assays with low sensitivities for HBsAg detection, due to their simplicity to operate. We developed a time-resolved fluorometric dry-reagent HBsAg immunoassay which meets the detection limit of high sensitivity EIAs but is simple to operate. To develop the assay, anti-HBsAg monoclonal antibody coated on europium nanoparticles was dried atop of biotinylated anti-HBsAg polyclonal antibody immobilized on streptavidin-coated microtiter wells. To test a sample in dry-reagent assay, serum sample and assay buffer were added to the wells, incubated, washed and europium signals were measured. The assay showed a detection limit of 0.25 ng/ml using HBsAg spiked in serum sample. When evaluated with 24 HBV positive and 37 negative serum samples, assay showed 100% sensitivity and specificity. Assay wells are stable for at least 26 weeks when stored at 4°C, and can tolerate elevated temperatures of up to 35°C for two weeks. The developed assay has high potential to be used in low-resource laboratories. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. Bright mono-aqua europium complexes based on triazacyclononane that bind anions reversibly and permeate cells efficiently.

    Science.gov (United States)

    Butler, Stephen J; McMahon, Brian K; Pal, Robert; Parker, David; Walton, James W

    2013-07-15

    A series of five europium(III) complexes has been prepared from heptadentate N5O2 ligands that possess a brightness of more than 10 mM(-1) cm(-1) in water, following excitation over the range λ=330-355 nm. Binding of several oxy anions has been assessed by emission spectral titrimetric analysis, with the binding of simple carboxylates, lactate and citrate involving a common ligation mode following displacement of the coordinated water. Selectivity for bicarbonate allows the rapid determination of this anion in human serum, with K(d)=37 mM (295 K). The complexes are internalised quickly into mammalian cells and exhibit a mitochondrial localisation at early time points, migrating after a few hours to reveal a predominant lysosomal distribution. Herein, we report the synthesis and complexation behaviour of strongly emissive europium (III) complexes that bind oxy-anions in aqueous media with an affinity and selectivity profile that is distinctively different from previously studied systems. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Highly luminescent charge-neutral europium(iii) and terbium(iii) complexes with tridentate nitrogen ligands.

    Science.gov (United States)

    Senthil Kumar, Kuppusamy; Schäfer, Bernhard; Lebedkin, Sergei; Karmazin, Lydia; Kappes, Manfred M; Ruben, Mario

    2015-09-21

    We report on the synthesis of tridentate-nitrogen pyrazole-pyridine-tetrazole (L(1)H) and pyrazole-pyridine-triazole (L(2)H) ligands and their complexation with lanthanides (Ln = Gd(iii), Eu(iii) and Tb(iii)) resulting in stable, charge-neutral complexes Ln(L(1))3 and Ln(L(2))3, respectively. X-ray crystallographic analysis of the complexes with L(1) ligands revealed tricapped trigonal coordination geometry around the lanthanide ions. All complexes show bright photoluminescence (PL) in the solid state, indicating efficient sensitization of the lanthanide emission via the triplet states of the ligands. In particular, the terbium complexes show high PL quantum yields of 65 and 59% for L(1) and L(2), respectively. Lower PL efficiencies of the europium complexes (7.5 and 9%, respectively) are attributed to large energy gaps between the triplet states of the ligands and accepting levels of Eu(iii). The triplet state energy can be reduced by introducing an electron withdrawing (EW) group at the 4 position of the pyridine ring. Such substitution of L(1)H with a carboxylic ester (COOMe) EW group leads to a europium complex with increased PL quantum yield of 31%. A comparatively efficient PL of the complexes dissolved in ethanol indicates that the lanthanide ions are shielded against nonradiative deactivation via solvent molecules.

  4. Highly Sensitive Luminescence Assessment of Bile Acid Using a Balofloxacin-Europium(III) Probe in Micellar Medium

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Huan; Zhao, Fang; Si, Hailin; Zhang, Shuaishuai; Wang, Chunchun; Qi, Peirong [Shihezi Univ., Shihezi (China)

    2012-12-15

    A novel and simple method of luminescence enhancement effect for the determination of trace amounts of bile acid was proposed. The procedure was based on the luminescence intensity of the balofloxacin-europium(III) complex that could be strongly enhanced by bile acid in the presence of sodium dodecyl benzene sulfonate (SDBS). Under the optimum conditions, the enhanced luminescence intensity of the system exhibited a good linear relationship with the bile acid concentration in the range 5.0 Χ 10{sup -9} - 7.0 Χ 10{sup -7} mol L{sup -1} with a detection limit of 1.3 Χ 10{sup -9} mol L.1 (3σ). The relative standard deviation (RSD) was 1.7% (n = 11) for 5.0 Χ 10{sup -8} mol L{sup -1} bile acid. The applicability of the method to the determination of bile acid was demonstrated by investigating the effect of potential interferences and by analyzing human serum and urine samples. The possible enhancement mechanism of luminescence intensity in balofloxacin-europium(III)-bile acid-SDBS system was also discussed briefly.

  5. Investigation of the influence of silver and tin on the luminescence of trivalent europium ions in glass

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez, J.A. [Department of Chemistry, University of Puerto Rico, Mayagueez, PR 00681 (United States); Lysenko, S. [Department of Physics, University of Puerto Rico, Mayagueez, PR 00681 (Puerto Rico); Liu, H., E-mail: hliu@uprm.ed [Department of Physics, University of Puerto Rico, Mayagueez, PR 00681 (Puerto Rico); Fachini, E.; Cabrera, C.R. [Center for Nanoscale Materials, University of Puerto Rico, Rio Piedras, PR 00931 (Puerto Rico)

    2010-01-15

    Europium-doped aluminophosphate glasses prepared by the melt-quenching technique have been studied by photoluminescence (PL) and X-ray photoelectron spectroscopy (XPS). The effects of silver and tin doping, and of further thermal processing on Eu{sup 3+} ions luminescence have been assessed. For the glass system containing only europium, Eu{sup 3+} PL observed under UV excitation is suggested to occur through energy transfer from the excited glass host. After silver and tin doping, an enhanced UV excited Eu{sup 3+} PL has been indicated to occur essentially due to radiative energy transfer from isolated Ag{sup +} ions and/or two fold-coordinated Sn centers. Since thermal processing of the material leads to a quenching effect on Eu{sup 3+} PL and Ag nanoparticles (NPs) formation due to reduction of silver ions by tin, XPS was employed in order to investigate the possibility for Eu{sup 3+}->Eu{sup 2+} reduction during HT as a potential source of the PL decrease. The data points towards Ag NPs as main responsible for the observed weakening of Eu{sup 3+} PL.

  6. Behaviour of europium (III) and its hydroxo and carbonate complexes in a solvent extraction system with HDBM in 2 M NaCl at 303 K

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez-Reyes, M. [Inst. Nacional de Investigaciones Nucleares, Dept. de Quimica, Mexico, D. F. (Mexico); Univ. Autonoma Metropolitana-Iztapalapa, Area de Electroquimica, Mexico, D. F. (Mexico); Solache-Rios, M. [Inst. Nacional de Investigaciones Nucleares, Dept. de Quimica, Mexico, D. F. (Mexico); Rojas-Hernandez, A. [Univ. Autonoma Metropolitana-Iztapalapa, Area de Electroquimica, Mexico, D. F. (Mexico)

    1999-07-01

    The behaviour of europium in the solvent extraction system Eu{sup 3+}-water-2 M NaCl-HDBM-benzene was studied, taking into account the pC{sub H} and the carbonate ion concentration in the solutions. The stability constants for the hydrolysis and carbonate complexes of europium were determined at 303 K in the same medium by pH titration followed by a computational refinement. The obtained data were: log {beta}{sub Eu,H} = -8.29 {+-} 0.02, log {beta}{sub Eu,2H} = -16.37 {+-} 0.02, log {beta}{sub Eu,3H} = -24.54 {+-} 0.11, log {beta}{sub Eu,4H} = -34.91 {+-} 0.26, log {beta}{sub CO{sub 2}{sup 2-},H} = 9.30 {+-} 0.05, log {beta}{sub Eu,CO{sub 3}{sup 2-}} = 5.96 {+-} 0.03, log {beta}{sub Eu,CO{sub 3}{sup 2-},H} = -1.24 {+-} 0.05 and log {beta}{sub Eu,CO{sub 3}{sup 2-},2H} = -11.39 {+-} 0.11. Log K{sub W} was -13.78 {+-} 0.06. The behaviour of europium in this solvent extraction system was simulated, taking into account the hydrolysis and carbonate complexes plus the formation of Eu(DBM){sub 3}(OH){sup 1-} and Eu(DBM){sub 3}(CO{sub 3}){sup 2-} in the aqueous phase. The only europium species considered in the organic phase was Eu(DBM){sub 3}. The first hydrolysis constant of europium was also determined by using this solvent extraction system under the same conditions. A good conformity was found with the results obtained by both techniques. (orig.)

  7. Bis(acridine-9-carboxylate)-nitro-europium(III) dihydrate complex a new apoptotic agent through Flk-1 down regulation, caspase-3 activation and oligonucleosomes DNA fragmentation.

    Science.gov (United States)

    Azab, Hassan A; Hussein, Belal H M; El-Azab, Mona F; Gomaa, Mohamed; El-Falouji, Abdullah I

    2013-01-01

    New bis(acridine-9-carboxylate)-nitro-europium(III) dihydrate complex was synthesized and characterized. In vivo anti-angiogenic activities of bis(acridine-9-carboxylate)-nitro-europium(III) dihydrate complex against Ehrlich ascites carcinoma (EAC) cells are described. The newly synthesized complex resulted in inhibition of proliferation of EAC cells and ascites formation. The anti-tumor effect was found to be through anti-angiogenic activity as evident by the reduction of microvessel density in EAC solid tumors. The anti-angiogenic effect is mediated through down-regulation of VEGF receptor type-2 (Flk-1). The complex was also found to significantly increase the level of caspase-3 in laboratory animals compared to the acridine ligand and to the control group. This was also consistent with the DNA fragmentation detected by capillary electrophoresis that proved the apoptotic effect of the new complex. Our complex exhibited anti-angiogenic and apoptotic activity in vivo, a thing that makes it a potential effective chemotherapeutic agent. The interaction of calf thymus DNA (ct-DNA) with bis(acridine-9-carboxylate)-nitro-europium(III) dihydrate complex has been investigated using fluorescence technique. A competitive experiment of the europium(III)-acridine complex with ethidium bromide (EB) to bind DNA revealed that interaction between the europium(III)-acridine and DNA was via intercalation. The interaction of the synthesized complex with tyrosine kinases was also studied using molecular docking simulation to further substantiate its mode of action. Copyright © 2012 Elsevier Ltd. All rights reserved.

  8. Europium(III) reduction and speciation within a Wells-Dawson heteropolytungstate.

    Science.gov (United States)

    Jing, Jing; Burton-Pye, Benjamin P; Francesconi, Lynn C; Antonio, Mark R

    2008-08-04

    The redox speciation of Eu(III) in the 1:1 stoichiometric complex with the alpha-1 isomer of the Wells-Dawson anion, [alpha-1-P 2W 17O 61] (10-), was studied by electrochemical techniques (cyclic voltammetry and bulk electrolysis), in situ XAFS (X-ray absorption fine structure) spectroelectrochemistry, NMR spectroscopy ( (31)P), and optical luminescence. Solutions of K 7[(H 2O) 4Eu(alpha-1-P 2W 17O 61)] in a 0.2 M Li 2SO 4 aqueous electrolyte (pH 3.0) show a pronounced concentration dependence to the voltammetric response. The fully oxidized anion and its reduced forms were probed by Eu L 3-edge XANES (X-ray absorption near edge structure) measurements in simultaneous combination with controlled potential electrolysis, demonstrating that Eu(III) in the original complex is reduced to Eu(II) in conjunction with the reduction of polyoxometalate (POM) ligand. After exhaustive reduction, the heteropoly blue species with Eu(II) is unstable with respect to cluster isomerization, fragmentation, and recombination to form three other Eu-POMs as well as the parent Wells-Dawson anion, alpha-[P 2W 18O 62] (6-). EXAFS data obtained for the reduced, metastable Eu(II)-POM before the onset of Eu(II) autoxidation provides an average Eu-O bond length of 2.55(4) A, which is 0.17 A longer than that for the oxidized anion, and consistent with the 0.184 A difference between the Eu(II) and Eu(III) ionic radii. The reduction of Eu(III) is unusual among POM complexes with Lindqvist and alpha-2 isomers of Wells-Dawson anions, that is, [Eu(W 5O 18) 2] (9-) and [Eu(alpha-2-As 2W 17O 61) 2] (17-), but not to the Preyssler complex anion, [EuP 5W 30O 110] (12-), and fundamental studies of materials based on coupling Eu and POM redox properties are still needed to address new avenues of research in europium hydrometallurgy, separations, and catalysis sciences.

  9. Structural, optical and electrical properties of europium picrate tetraethylene glycol complex as emissive material for OLED

    Energy Technology Data Exchange (ETDEWEB)

    Kusrini, Eny, E-mail: ekusrini@che.ui.ac.id [Department of Chemical Engineering, Faculty of Engineering, Universitas Indonesia, 16424 Depok (Indonesia); Saleh, Muhammad I.; Adnan, Rohana [School of Chemical Sciences, Universiti Sains Malaysia, 11800 Penang (Malaysia); Yulizar, Yoki [Department of Chemistry, Faculty of Mathematics and Natural Sciences, Universitas Indonesia, 16424 Depok (Indonesia); Sha Shiong, Ng; Fun, H.K. [School of Physics, Universiti Sains Malaysia, 11800 Penang (Malaysia); Adhha Abdullah, M.A.; Mamat, Mazidah [Department of Chemical Sciences, Faculty of Science and Technology, Universiti Malaysia Terengganu, 21030 Kuala Terengganu, Terengganu Darul Iman (Malaysia); Za' aba, N.K.; Abd. Majid, W.H. [Solid State Research Laboratory, Department of Physics, Universiti Malaya, 50603 Kuala Lumpur (Malaysia)

    2012-01-15

    A new europium complex [Eu(Pic){sub 2}(H{sub 2}O)(EO4)](Pic).0.75H{sub 2}O was synthesized and used as the emission material for the single layer device structure of ITO/EO4-Eu-Pic/Al, using a spin-coating technique. Study on the optical properties of the [Eu(Pic){sub 2}(H{sub 2}O)(EO4)](Pic).0.75H{sub 2}O complex where EO4=tetraethylene glycol and Pic=picrate anion, had to be undertaken before being applicable to the study of an organic light emitting diode (OLED). The electrical property of an OLED using current-voltage (I-V) measurement was also studied. In complex, the Eu(III) ion was coordinated with the EO4 ligand as a pentadentate mode, one water molecule, and with two Pic anions as bidentate and monodentate modes, forming a nine-coordination number. The photoluminescence (PL) spectra of the crystalline complex in the solid state and its thin film showed a hypersensitive peak at 613.5-614.9 nm that assigned to the {sup 5}D{sub 0}{yields}{sup 7}F{sub 2} transition. A narrow band emission from the thin film EO4-Eu-Pic was obtained. The typical semiconductor I-V curve of device ITO/EO4-Eu-Pic/Al showed the threshold and turn on voltages at 1.08 and 4.6 V, respectively. The energy transfer process from the ligand to the Eu(III) ion was discussed by investigating the excitation and PL characteristics. Effect of the picrate anion on the device performance was also studied. - Highlights: > The [Eu(Pic){sub 2}(H{sub 2}O)(EO4)](Pic).0.75(H{sub 2}O) is crystallized in triclinic with space group P-1. > The complex is applied as a emissive center in single layer device structure of ITO/EO4-Eu-Pic/Al. > The complex displays a red luminescence in both the crystalline complex and its thin film state. > The low turn on voltage of the device (4.6 V), indicating that this material is suitable for OLED. > The roughness and morphology of the thin film affects luminance and electrical properties of OLED.

  10. Caracterización de la capa de boruros formada durante la austenización de un hierro nodular austemperizado//Characterization of borides coating formed during austenitization of an austempered ductile iron

    Directory of Open Access Journals (Sweden)

    Urbano Ordóñez‐Hernández

    2015-01-01

    Full Text Available En este trabajo se ha investigado el efecto de la austenitización y el borurado simultáneos, a 950 ºC, en la microestructura, la microdureza Vickers y el espesor de la capa borurada en medio líquido de un hierro nodular austemperizado no aleado. Se demostró que es posible obtener una capa de boruros de hierro muy bien estructurada con la microdureza Vickers suficientemente alta (1400 HVy con adecuado espesor de capa de 67 μm, sobre un sustrato de ausferrita típico de las fundiciones nodulares austemperizadas. Por medio de un ensayo pin on disc modificado, se comprobó la superior resistencia al desgaste abrasivo de la capa de boruros depositada durante la austenización del ADI, comparada con la máxima obtenida durante el austempering de éste sin aplicar el recubrimiento.Palabras claves: hierro nodular, borurado, austenización, austemperizado.______________________________________________________________________________AbstractThe effect of simultaneous austenitization and boriding at 950 ºC, on microstructure, Vickers hardness and boronized layer thickness of a non alloyed austempered ductile iron has been investigated. It was demonstrated that it is possible to obtain a well formed boronized layer with a Vicker hardness sufficiently high (1400 HV, and with an appropriated 67μm layer thickness, on a typical ausferrite ADI substrate. By using a modified pin on disc test, it was demonstrated the higher abrasion wear resistance of borides layer deposited during ADI austenitization process, compared with Vickers hardness of low temperature noncoated austempered ductile iron.Key words: ductile iron, boriding, austenitization, austempering.

  11. Comportamiento parabólico del crecimiento de capas boradas en los aceros Y8A y X12M // Parabolic behavior of boriding layers growth in Y8A and X12M steels

    Directory of Open Access Journals (Sweden)

    C. Figueroa Hernández

    1999-01-01

    Full Text Available Se determina la influencia que tienen los principales parámetros tecnológicos del borado en el crecimiento de las capas y secorrobora el cumplimiento de la ley parabólica para predecir este comportamiento en los aceros Y8A y X12M.El proceso de borado se aplica en una mezcla de carburo de silicio y bórax (70 y 30 % a la temperatura de 850, 900 y 950 oCdurante un tiempo de 2, 4 y 6 horas. Como variable dependiente se seleccionó la profundidad del recubrimiento, a partir de lacual se obtuvieron los coeficientes del crecimiento parabólico y la energía de activación en función de la temperatura, el tiempodel proceso y el tipo de acero.La caracterización metalográfica reveló la presencia de la fase Fe2BPalabras claves: Borado, recubrimiento superf icial , t ecnología de recubrimiento.__________________________________________________________________________AbstractIt was determined the influence of the main technological parameters of the boriding process, and a mathematical model thatallows to predict this conduct on the steels Y8A and X12M steels was obtained.The boriding process is applied in a mixture of silicon carbide and borax (70 and 30% at 850, 900 and 950 oC temperatureduring a period of time 2, 4 and 6 hours. As an independent variable the depth of the coat was selected.It was obtained the parabolic growth coefficients, and the activation energy according to temperature, time and the chemicalcomposition of steel.Metallografic analysis reveals the presence of Fe2B phase.Key words: Boriding process, superf icial coat , coat technology.

  12. History of ``NANO''-Scale VERY EARLY Solid-State (and Liquid-State) Physics/Chemistry/Metallurgy/ Ceramics; Interstitial-Alloys Carbides/Nitrides/Borides/...Powders and Cermets, Rock Shocks, ...

    Science.gov (United States)

    Maiden, Colin; Siegel, Edward

    History of ``NANO'': Siegel-Matsubara-Vest-Gregson[Mtls. Sci. and Eng. 8, 6, 323(`71); Physica Status Solidi (a)11,45(`72)] VERY EARLY carbides/nitrides/borides powders/cermets solid-state physics/chemistry/metallurgy/ ceramics FIRST-EVER EXPERIMENTAL NANO-physics/chemistry[1968 ->Physica Status Solidi (a)11,45(`72); and EARLY NANO-``physics''/NANO-``chemistry'' THEORY(after: Kubo(`62)-Matsubara(`60s-`70s)-Fulde (`65) [ref.: Sugano[Microcluster-Physics, Springer('82 `98)

  13. Synthesis, characterization and thermoelectric properties of metal borides, boron carbides and carbaborides; Synthese, Charakterisierung und thermoelektrische Eigenschaften ausgewaehlter Metallboride, Borcarbide und Carbaboride

    Energy Technology Data Exchange (ETDEWEB)

    Guersoy, Murat

    2015-07-06

    This work reports on the solid state synthesis and structural and thermoelectrical characterization of hexaborides (CaB{sub 6}, SrB{sub 6}, BaB{sub 6}, EuB{sub 6}), diboride dicarbides (CeB{sub 2}C{sub 2}, LaB{sub 2}C{sub 2}), a carbaboride (NaB{sub 5}C) and composites of boron carbide. The characterization was performed by X-ray diffraction methods and Rietveld refinements based on structure models from literature. Most of the compounds were densified by spark plasma sintering at 100 MPa. As high-temperature thermoelectric properties the Seebeck coefficients, electrical conductivities, thermal diffusivities and heat capacities were measured between room temperature and 1073 K. ZT values as high as 0.5 at 1273 K were obtained for n-type conducting EuB{sub 6}. High-temperature X-ray diffraction also confirmed its thermal stability. The solid solutions Ca{sub x}Sr{sub 1-x}B{sub 6}, Ca{sub x}Ba{sub 1-x}B{sub 6} and Sr{sub x}Ba{sub 1-x}B{sub 6} (x = 0, 0.25, 0.5, 0.75, 1) are also n-type but did not show better ZT values for the ternary compounds compared to the binaries, but for CaB{sub 6} the values of the figure of merit (ca. 0.3 at 1073 K) were significantly increased (ca. 50 %) compared to earlier investigations which is attributed to the densification process. Sodium carbaboride, NaB{sub 5}C, was found to be the first p-type thermoelectric material that crystallizes with the hexaboride-structure type. Seebeck coefficients of ca. 80 μV . K{sup -1} were obtained. Cerium diboride dicarbide, CeB{sub 2}C{sub 2}, and lanthanum diboride dicarbide, LaB{sub 2}C{sub 2}, are metallic. Both compounds were used as model compounds to develop compacting strategies for such layered borides. Densities obtained at 50 MPa were determined to be higher than 90 %. A new synthesis route using single source precursors that contain boron and carbon was developed to open the access to new metal-doped boron carbides. It was possible to obtain boron carbide, but metal-doping could not be

  14. Synthesis and characterization of new metal-rich borides with boron fragments; Synthese und Charakterisierung von neuartigen metallreichen Boriden mit Borfragmenten

    Energy Technology Data Exchange (ETDEWEB)

    Mbarki, Mohammed

    2016-03-30

    The present dissertation deals with the synthesis and characterization of new metal-rich borides of the Ce{sub 7}Ni{sub 5±x}Ge{sub 3±x}In{sub 6{sup -}}, Nb{sub 2}OsB{sub 2{sup -}} and NbRuB-type.The samples are synthesized by a solid state reaction route from elements using an electric arc furnace. The structural characterization of the compounds was carried out by using X-ray diffraction methods on powder samples and single crystals. The chemical composition of single-crystals was verified by EDX analyses. Moreover, the magnetic properties of suitable samples were investigated by SQUID magnetometry.The crystal structure of compounds with the nominal composition NbFe{sub 1-x}Ir{sub 6+x}B{sub 8} is successfully solved from single crystal X-ray data. The most prominent feature in this structure are one-dimensional chains along the c-axis formed by the magnetically active element iron on a site of mixed occupation with Iridium (Fe: Ir = 0.77 (2) 0.23 (2)). Thermomagnetic investigations reveal, that ferromagnetic ordering is observed below the Curie temperature (TC) of 350 K. Theoretical investigations suggest that the iron-chains are mainly responsible for the ferromagnetic ordering. In addition, the magnetocaloric effect (MCE) is calculated using isothermal magnetization measurements at several temperatures. The maximal magnetic entropy change ΔS = 0.032 J kg{sup -1} K{sup -1} is observed in the vicinity of T{sub C}. For the phases Nb{sub 6}Mn{sub 0,75(2)}Ir{sub 6,25(2)}B{sub 8} and Nb{sub 6}Co{sub 1,09(2)}Ir{sub 5,91(2)}B{sub 8} a relationship between the measured ferrimagnetic ordering and the crystal structure is found. Tiny superstructure reflections measured by Selected Area Electron Diffraction (SEAD) indicate a different crystal system for those compounds, which allows a ferrimagnetic spin arrangement within this crystal structure.In the second part of the thesis new results about the Nb{sub 2}OsB{sub 2-} and NbRuB-type borides are presented, which both

  15. The studies on complex formation of metal borides in the reaction system of epoxidation of 1-octene with tert-butyl hydroperoxide by IR spectroscopy

    OpenAIRE

    Makota, Oksana; Trach, Yuriy

    2007-01-01

    Вивчено комплексоутворення боридів молібдену і ванадію в реакційній системі епоксидування октену-1 гідропероксидом трет-бутилу методом інфрачервоної спектроскопії. Показано, що октен-1 утворює комплекс з металевою складовою у випадку бориду молібдену і з боридною складовою у випадку бориду ванадію.The complex formation of molybdenum and vanadium borides in the reaction system of 1-octene epoxidation with tert -butyl hydroperoxide by infrared spectroscopic analysis was studied. It was sh...

  16. Synthesis of Luminescent Ink from Europium-Doped Y2O3 Dispersed in Polyvinyl Alcohol Solution

    Directory of Open Access Journals (Sweden)

    Astuti

    2009-01-01

    Full Text Available Luminescent ink from europium-doped Y2O3 ( Y2O3:Eu has been synthesized by two steps method: first, synthesis of luminescent powder of Y2O3:Eu by simple heating of metallic nitrates in a polymer solution and second, dispersing the powder in a polyvinyl alcohol (PVA solution. The stability of the ink (luminescent colloid was strongly affected by mixing process of the powder and the solution. Mixing process must be performed for a long time (about 8 hours at above room temperature to product stable colloids. We observed that mixing at 30–40∘C resulted in a stable and highly dispersed colloid. The writing test was performed on a white paper to show the potential use of the colloid for making security codes.

  17. Induced europium CPL for the selective signalling of phosphorylated amino-acids and O-phosphorylated hexapeptides.

    Science.gov (United States)

    Neil, Emily R; Fox, Mark A; Pal, Robert; Parker, David

    2016-05-17

    Two bright, europium(iii) complexes based on an achiral heptadentate triazacyclononane ligand bearing two strongly absorbing chromophores have been evaluated for the selective emission and CPL signalling of various chiral O-phosphono-anions. Binding of O-phosphono-Ser and Thr gives rise to a strong induced CPL signature and a favoured Δ complex configuration is adopted. A similarly large induced CPL signal arises when [Eu·](2+) binds to lysophosphatidic acid (LPA), where the strong binding (log K 5.25 (295 K)) in methanol allowed its detection over the range 5 to 40 μM. Strong and chemoselective binding to the phosphorylated amino-acid residues was also observed with a set of four structurally related hexapeptides: in one case, the sign of the gem value in the ΔJ = 1 transition allowed differentiation between the binding to O-P-Ser and O-P-Tyr residues.

  18. A new europium(III)-β-diketonate complex based on diphenylethyne as red phosphors applied in LED

    Energy Technology Data Exchange (ETDEWEB)

    Shao, Guang, E-mail: shaog@mail.sysu.edu.cn [School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou 510275 (China); Zhang, Na; Lin, Duan [School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou 510275 (China); Feng, Kenjun [Department of Chemical Engineering, Hui-Zhou University, Huizhou 516007 (China); Cao, Rihui, E-mail: caorihui@mail.sysu.edu.cn [School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou 510275 (China); Gong, Menglian [School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou 510275 (China)

    2013-06-15

    A new europium(III) ternary complex based on a fluorinated β-diketonate ligand and 1,10-phenanthroline as an ancillary ligand has been prepared and evaluated as a candidate for light-emitting diode (LED). The complex exhibits a high decomposition temperature (316 °C). Photophysical properties such as FT-IR spectra, UV–vis absorption spectra, excitation and emission spectra, luminescence decay curve and quantum yield were investigated. The excitation band is well matched with the characteristic emission of 395 nm-emitting InGaN chips. The complex exhibits an efficient energy transfer pathway from the ligands to the central Eu{sup 3+} ion via a ligand-sensitized luminescence process. An intense red-emitting LED was fabricated by coating the complex onto a 395 nm-emitting InGaN chip, and its Commission International de I'Eclairage (CIE) chromaticity coordinate (x=0.6389, y=0.3255) is close to the National Television Standard Committee (NTSC) standard value for red color. Meanwhile, the energy transfer from the InGaN chip to the complex is very efficient. All the findings demonstrate the potential application of the Eu(III) complex as red-emitting phosphors for UV-based white LEDs. -- Highlights: ► A new europium(III)-β-diketonate complex was synthesized and characterized. ► Thermal stability and photophysical properties were investigated in detail. ► PL mechanism was proposed to involve a ligand-sensitized luminescence process. ► An intense red-emitting LED was fabricated by using the complex. ► CIE chromaticity coordinate is close to NTSC standard value for red color.

  19. Mitochondria Targetable Time-Gated Luminescence Probe for Singlet Oxygen Based on a β-Diketonate-Europium Complex.

    Science.gov (United States)

    Sun, Jingyan; Song, Bo; Ye, Zhiqiang; Yuan, Jingli

    2015-12-21

    Singlet oxygen ((1)O2) plays a key role in the photodynamic therapy (PDT) technique of neoplastic diseases. In this work, by using a 9,10-dimethyl-2-anthryl-containing β-diketone, 1,1,1,2,2-pentafluoro-5-(9',10'-dimethyl-2'-anthryl)-3,5-pentanedione (Hpfdap), as a (1)O2-recognition ligand, a novel β-diketonate-europium(III) complex that can act as a luminescence probe for (1)O2, [Eu(pfdap)3(tpy)] (tpy = 2,2',2″-terpyridine), has been designed and synthesized for the time-gated luminescence detection of (1)O2 in living cells. The complex is weakly luminescent due to the quenching effect of 9,10-dimethyl-2-anthryl groups. After reaction with (1)O2, accompanied by the formation of endoperoxides of 9,10-dimethyl-2-anthryl groups, the luminescence quenching disappears, so that the long-lived luminescence of the europium(III) complex is switched on. The complex showed highly selective luminescence response to (1)O2 with a remarkable luminescence enhancement. Combined with the time-gated luminescence imaging technique, the complex was successfully used as a luminescent probe for the monitoring of the time-dependent generation of (1)O2 in 5-aminolevulinic acid (a PDT drug) loaded HepG2 cells during the photodynamic process. In addition, by coloading the complex and a mitochondrial indicator, Mito-Tracker Green, into HepG2 cells, the specific localization of [Eu(pfdap)3(tpy)] molecules in mitochondria of HepG2 cells was demonstrated by confocal fluorescence imaging measurements.

  20. Excitation energy transfer in europium chelate with doxycycline in the presence of a second ligand in micellar solutions of nonionic surfactants

    Science.gov (United States)

    Smirnova, T. D.; Shtykov, S. N.; Kochubei, V. I.; Khryachkova, E. S.

    2011-01-01

    The complexation of Eu3+ with doxycycline (DC) antibiotic in the presence of several second ligands and surfactant micelles of different types is studied by the spectrophotometric and luminescence methods. It is found that the efficiency of excitation energy transfer in Eu3+-DC chelate depends on the nature of the second ligand and surfactant micelles. Using thenoyltrifluoroacetone (TTA) as an example, it is shown that the second ligand additionally sensitizes the europium fluorescence, and the possibility of intermediate sensitization of DC and then of europium is shown by the example of 1,10-phenanthroline. In all cases, the excitation energy transfer efficiency was increased due to the so-called antenna effect. The decay kinetics of the sensitized fluorescence of the binary and mixed-ligand chelates in aqueous and micellar solutions of nonionic surfactants is studied and the relative quantum yields and lifetimes of fluorescence are determined.

  1. A Smart Europium-Ruthenium Complex as Anticancer Prodrug: Controllable Drug Release and Real-Time Monitoring under Different Light Excitations.

    Science.gov (United States)

    Li, Hongguang; Xie, Chen; Lan, Rongfeng; Zha, Shuai; Chan, Chi-Fai; Wong, Wing-Yan; Ho, Ka-Lok; Chan, Brandon Dow; Luo, Yuxia; Zhang, Jing-Xiang; Law, Ga-Lai; Tai, William C S; Bünzli, Jean-Claude G; Wong, Ka-Leung

    2017-11-09

    A unique, dual-function, photoactivatable anticancer prodrug, RuEuL, has been tailored that features a ruthenium(II) complex linked to a cyclen-europium chelate via a π-conjugated bridge. Under irradiation at 488 nm, the dark-inactive prodrug undergoes photodissociation, releasing the DNA-damaging ruthenium species. Under evaluation-window irradiation (λirr = one-photon 350 nm or two-photon 700 nm), the drug delivery process can be quantitatively monitored in real-time because of the long-lived red europium emission. Linear relationships between released drug concentration and ESI-MS or luminescence responses are established. Finally, the efficiency of the new prodrug is demonstrated both in vitro RuEuL anticancer prodrug over some existing ones and open the way for decisive improvements in multipurpose prodrugs.

  2. Structural and optical analysis on europium doped AZrO{sub 3} (A=Ba, Ca, Sr) phosphor for display devices application

    Energy Technology Data Exchange (ETDEWEB)

    Dubey, Vikas, E-mail: jsvikasdubey@gmail.com [Department of Physics, Bhilai Institute of Technology Raipur, 493661 (India); Tiwari, Neha [Department of Physics, Govt. Model Science College, Jabalpur (India)

    2016-05-06

    Behavior displayed by europium doped AZrO{sub 3} phosphor which was synthesized by solid state reaction method. For synthesis of BaZrO{sub 3}, SrZrO{sub 3} and CaZrO{sub 3} phosphor with fixed concentration of europium ion was calcination at 1000°C and sintered at 1300°C following intermediate grinding. Synthesized sample was characterized by X-ray diffraction analysis and crystallite sized was calculated by Scherer’s formula. From PL spectra of prepared phosphors shows intense emission centred at 612nm (red emission) with high intensity for SrZrO{sub 3}:Eu{sup 3+}. For europium doped BaZrO{sub 3} and CaZrO{sub 3} (613nm) phosphor shows less intense PL spectra as compared to SrZrO{sub 3}:Eu{sup 3+}. The strong emission peak of AZrO{sub 3}:Eu{sup 3+} phosphor is due to forced electric dipole transition of {sup 5}D{sub 0} to {sup 7}F{sub 2} centered at 612 and 613nm. It is characteristic red emission for europium ion. The excitation spectra of AZrO{sub 3}:Eu{sup 3+} phosphor mainly consists of the charge transfer and (CTB) of Eu{sup 3+} located in 200–350 nm centred at 254nm. The present phosphors can act as single host for red light emission in display devices. The CIE coordinates were calculated by Spectrophotometric method using the spectral energy distribution of the AZrO{sub 3}:Eu{sup 3+} sample.

  3. Metal-organic framework luminescence in the yellow gap by codoping of the homoleptic imidazolate ∞(3)[Ba(Im)2] with divalent europium.

    Science.gov (United States)

    Rybak, Jens-Christoph; Hailmann, Michael; Matthes, Philipp R; Zurawski, Alexander; Nitsch, Jörn; Steffen, Andreas; Heck, Joachim G; Feldmann, Claus; Götzendörfer, Stefan; Meinhardt, Jürgen; Sextl, Gerhard; Kohlmann, Holger; Sedlmaier, Stefan J; Schnick, Wolfgang; Müller-Buschbaum, Klaus

    2013-05-08

    The rare case of a metal-triggered broad-band yellow emitter among inorganic-organic hybrid materials was achieved by in situ codoping of the novel imidazolate metal-organic framework ∞(3)[Ba(Im)2] with divalent europium. The emission maximum of this dense framework is in the center of the yellow gap of primary light-emitting diode phosphors. Up to 20% Eu2+ can be added to replace Ba2+ as connectivity centers without causing observable phase segregation. High-resolution energy-dispersive X-ray spectroscopy showed that incorporation of even 30% Eu2+ is possible on an atomic level, with 2-10% Eu2+ giving the peak quantum efficiency (QE = 0.32). The yellow emission can be triggered by two processes: direct excitation of Eu2+ and an antenna effect of the imidazolate linkers. The emission is fully europium-centered, involving 5d → 4f transitions, and depends on the imidazolate surroundings of the metal ions. The framework can be obtained by a solvent-free in situ approach starting from barium metal, europium metal, and a melt of imidazole in a redox reaction. Better homogeneity for the distribution of the luminescence centers was achieved by utilizing the hydrides BaH2 and EuH2 instead of the metals.

  4. α-Titanium phosphate intercalated with propylamine: An alternative pathway for efficient europium(III uptake into layered tetravalent metal phosphates

    Directory of Open Access Journals (Sweden)

    Jorge García-Glez

    2017-09-01

    Full Text Available α-Ti(HPO42·H2O (α-TiP and its propylamine intercalation product, Ti(HPO42·2C3H7NH2·H2O (α-TiPPr, have been synthesized and characterized. Later, their sorption capacity for europium(III was investigated, and this purpose was accomplished by treating α-TiP and α-TiPPr with europium(III nitrate solutions at different concentrations until the equilibrium is reached. All samples were characterized, among others, by powder X-ray diffraction (PXRD, scanning and transmission electron microscopies (SEM, TEM, STEM-EDX, SAED, thermogravimetric analysis (TGA, and photoluminescence (PL measurements. The results show that the Eu3+ uptake is limited to surface when α-TiP is used as sorbent. Nevertheless, the Eu-retention is considerably enhanced with α-TiPPr as a consequence of an ion-exchange process into the interlayer space of the layered titanium phosphate (involving propylammonium cations, C3H7NH3+, and hexahydrate europium(III species, [Eu(H2O6]3+, and the crystal structure of a hypothetical final product, α-[Eu(H2O6]2/3Ti(PO42·[(H2O6]1/3, has been proposed by using DFT calculations.

  5. ScRu2B3 and Sc2RuB6: Borides Featuring a 2D Infinite Boron Clustering.

    Science.gov (United States)

    Salamakha, Leonid P; Sologub, Oksana; Stöger, Berthold; Rogl, Peter Franz; Waas, Monika; Kapustianyk, Volodymyr B; Bauer, Ernst

    2017-09-05

    Two borides, ScRu2B3 and Sc2RuB6, were obtained by argon-arc melting of the elements followed by annealing at 800 °C. ScRu2B3 exhibits a new structure type with the space group Cmcm (a = 3.0195(2) Å, b = 15.4056(8) Å, c = 5.4492(3) Å; single crystal X-ray data; RF(2) = 0.0105). Sc2RuB6 adopts the Y2ReB6-type structure (space group Pbam; a = 8.8545(2) Å, b = 11.1620(3) Å, c = 3.4760(1) Å; single crystal X-ray data; RF(2) = 0.0185). ScRu2B3 displays an unusual intergrowth of CeCo3B2- and AlB2-related slabs; a striking feature is a boat configuration of puckered boron hexagons within infinite graphite like boron layers (6(3) nets). Sc2RuB6 presents two-dimensional planar nets of condensed boron pentagons, hexagons, and heptagons sandwiched between metal layers. In Sc/Y substituted Y2ReB6-type, Y atoms are distributed exclusively inside the boron heptagons. Exploration of the Sc-Ru-B system at 800 °C including binary boundaries employing EPMA and powder X-ray diffraction technique furthermore rules out the existence of previously reported "ScRuB4" but confirms the formation and crystal structure of Sc2Ru5B4. ScRu4B4 forms in cast alloys (LuRu4B4-type structure; space group I41/acd (No. 142), a = 7.3543(2) Å, c = 14.92137(8) Å). Cell parameters and atomic coordinates have been refined for ScRu2B3, Sc2RuB6, and ScRu4B4 in the scope of the generalized gradient approximation. Ab initio electronic structure calculations indicate a moderate electronic density of states at the Fermi level situated near the upper edge of essentially filled d-bands. Electrical resistivity measurements characterize ScRu2B3 and Sc2RuB6 as metals in concord with electronic band structure calculations.

  6. Electron tunneling transport across heterojunctions between europium sulfide and indium arsenide

    Science.gov (United States)

    Kallaher, Raymond L.

    This dissertation presents research done on utilizing the ferromagnetic semiconductor europium sulfide (EuS) to inject spin polarized electrons into the non-magnetic semiconductor indium arsenide (InAs). There is great interest in expanding the functionality of modern day electronic circuits by creating devices that depend not only on the flow of charge in the device, but also on the transport of spin through the device. Within this mindset, there is a concerted effort to establish an efficient means of injecting and detecting spin polarized electrons in a two dimensional electron system (2DES) as the first step in developing a spin based field effect transistor. Thus, the research presented in this thesis has focused on the feasibility of using EuS, in direct electrical contact with InAs, as a spin injecting electrode into an InAs 2DES. Doped EuS is a concentrated ferromagnetic semiconductor, whose conduction band undergoes a giant Zeeman splitting when the material becomes ferromagnetic. The concomitant difference in energy between the spin-up and spin-down energy bands makes the itinerant electrons in EuS highly spin polarized. Thus, in principle, EuS is a good candidate to be used as an injector of spin polarized electrons into non-magnetic materials. In addition, the ability to adjust the conductivity of EuS by varying the doping level in the material makes EuS particularly suited for injecting spins into non-magnetic semiconductors and 2DES. For this research, thin films of EuS have been grown via e-beam evaporation of EuS powder. This growth technique produces EuS films that are sulfur deficient; these sulfur vacancies act as intrinsic electron donors and the resulting EuS films behave like heavily doped ferromagnetic semiconductors. The growth parameters and deposition procedures were varied and optimized in order to fabricate films that have minimal crystalline defects. Various properties and characteristics of these EuS films were measured and compared to

  7. Synthesis, Optical Investigation and Biological Properties of Europium(III) Complexes with 2-(4-Chlorophenyl)-1-(2-Hydroxy-4-Methoxyphenyl)Ethan-1-one and Ancillary Ligands.

    Science.gov (United States)

    Nandal, Poonam; Khatkar, S P; Kumar, Rajesh; Khatkar, Avni; Taxak, V B

    2017-01-01

    Synthesis and photoluminescence behaviour of six novel europium complexes with novel β-hydroxyketone ligand, 2-(4-chlorophenyl)-1-(2-hydroxy-4-methoxyphenyl)ethan-1-one (CHME) and 2,2'-bipyridine (bipy) or neocuproine (neo) or 1,10-phenanthroline (phen) or 5,6-dimethyl-1,10-phenanthroline (dmphen) or bathophenanthroline (bathophen) were reported in solid state. The free ligand CHME and europium complexes, Eu(CHME)3.2H2O [1] Eu(CHME)3.bipy [2], Eu(CHME)3.neo [3], Eu(CHME)3.phen [4], Eu(CHME)3.dmphen [5] and Eu(CHME)3.bathophen [6]were characterized by elemental analysis, FT-IR and 1H-NMR. The photoluminescence emission spectra exhibited four characteristic peaks arising from the 5D0 → 7FJ (J = 1-4) transitions of the europium ion in the solid state on monitoring excitation at λex = 395 nm. The luminescence decay curves of these europium complexes possess single exponential behaviour indicating the presence of a single luminescent species and having only one site symmetry in the complexes. The luminescence quantum efficiency (η) and the experimental intensity parameters, Ω 2 and Ω 4 of europium complexes have also been calculated on the basis of emission spectra and luminescence decay curves. In addition, the antimicrobial and antioxidant activities were also studied of the investigated complexes.

  8. Highly luminescent pure-red-emitting fluorinated β-diketonate europium(III) complex for full solution-processed OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Joao P. [CEMDRX, Physics Department, Universidade de Coimbra, Rua Larga, Coimbra P-3004-516 (Portugal); Serviço de Medicina Nuclear, SESARAM E.P.E., Avenida Luís de Camões 57, Funchal 9004-514, Madeira (Portugal); Martín-Ramos, Pablo [CEMDRX, Physics Department, Universidade de Coimbra, Rua Larga, Coimbra P-3004-516 (Portugal); Higher Technical School of Telecommunications Engineering, Universidad de Valladolid, Campus Miguel Delibes, Paseo Belén 15, Valladolid 47011 (Spain); Coya, Carmen, E-mail: carmen.coya@urjc.es [Escuela Superior de Ciencias Experimentales y Tecnología (ESCET), Universidad Rey Juan Carlos, Madrid 28933 (Spain); Silva, Manuela Ramos [CEMDRX, Physics Department, Universidade de Coimbra, Rua Larga, Coimbra P-3004-516 (Portugal); Eusebio, M. Ermelinda S. [Chemistry Department, Faculdade de Ciências e Tecnologia, Universidade de Coimbra, Coimbra P-3004-535 (Portugal); Andrés, Alicia de [Instituto de Ciencia de Materiales de Madrid, Consejo Superior de Investigaciones Científicas (CSIC), Cantoblanco, Madrid 28049 (Spain); Álvarez, Ángel L. [Escuela Superior de Ciencias Experimentales y Tecnología (ESCET), Universidad Rey Juan Carlos, Madrid 28933 (Spain); Martín-Gil, Jesús [Advanced Materials Laboratory, ETSIIAA, Universidad de Valladolid, Avenida de Madrid 44, Palencia 34004 (Spain)

    2015-03-15

    Current manufacturing technologies for OLEDs involve the use of expensive high vacuum techniques and call for thermal stability requirements which are not fulfilled by many materials. These problems disappear when the OLED films are deposited directly from solution. In this study, we have designed, synthesized and characterized a novel octacoordinated complex, Tris(1-(4-chlorophenyl)-4,4,4-trifluoro-1, 3-butanedionate)mono(bathophenanthroline) europium(III), to be used as a “complex-only” emissive layer in wet-processed OLEDs. Upon excitation in the UV region, very efficient energy transfer from the ligands to Eu{sup 3+} takes place, giving rise to intense red emission with very high monochromaticity (R=19), both in powder and as a thin film. The decay times of 754 µs (powder) and 620 µs (thin film) are comparable to those of the most efficient Eu{sup 3+} β-diketonate complexes reported to date. The same energy transfer leading to saturated red and narrow emission is also observed in the OLED device (glass/ITO/PEDOT:PSS/[Eu(cbtfa){sub 3}(bath)]/Ca/Al) when biased at >5.2 V. Its high quantum efficiency (∼60%), good thermal stability up to 200 °C and adequate thin film forming properties make this material a promising chromophore for cost-effective OLEDs. - Highlights: • A highly fluorinated europium(III) octacoordinated complex, [Eu(cbtfa)3(bath)], has been synthesized and its structure elucidated by single crystal X-ray diffraction. • The chosen coordination environment is well-suited for sensitizing the luminescence of the Eu{sup 3+} ion, achieving very efficient energy transfer from the organic ligands (excited in the UV region) to the rare earth ion, leading to highly efficient (Q∼60% in crystalline powder and Q∼50% in thin film) and saturated red photoluminescence. • The material has also been integrated into a single active layer, full solution-processed OLED, with ITO/PEDOT:PSS/[Eu(cbtfa)3(bath)]/ Ca/Al structure.

  9. Simultaneous analysis of free and humic acid complexed europium and gadolinium species by CE-ICP-MS

    Energy Technology Data Exchange (ETDEWEB)

    Kautenburger, R.; Nowotka, K.; Beck, H.P. [Institut fuer Anorganische und Analytische Chemie und Radiochemie, Universitaet des Saarlandes, P.O. Box 151150, 66041 Saarbruecken (Germany)

    2005-07-01

    Full text of publication follows: For the long-term safety assessment of waste repositories, detailed information about geo-chemical behaviour of radioactive and toxic metal ions under environmental conditions (geological matrix and aquifer systems) is necessary. It includes knowledge about the mechanism of relevant geochemical reactions, as well as thermodynamic and kinetic data. Several previous studies have shown that humic acid can play an important role in the immobilisation or mobilization of metal ions due to complexation and colloid formation. In this project we investigate the complexation behaviour of humic acid (purified Aldrich humic acid) and its influence on the migration of the lanthanides europium and gadolinium (homologues of the actinides americium and curium) in the the ternary system consisting of these heavy metals, humic acid and kaolinite (KGa-1b) as geological model system under conditions close to nature. Capillary electrophoresis (CE, Beckman Coulter P/ACE MDQ), with its excellent separation performance, was coupled to Inductively Coupled Plasma Mass Spectrometry (ICP-MS, VG Elemental Plasma Quad 3) to obtain a high sensitivity for the determination of the rare earth elements europium (Eu{sup 3+}) and gadolinium (Gd{sup 3+}) and their complexes with humic acid. Additionally, the used humic acid was halogenated with iodine as ICP-MS marker. A fused-silica capillary was flexibly fitted into a MicroMist 50 {mu}l nebulizer with a Cinnabar cyclonic spray chamber. The chamber was chilled to a temperature of 4 deg. C for best sensitivity. 200 ppb of caesium were added to the CE separation buffer to observe the capillary flow. A make-up fluid including 4 ppb Ho as an internal standard was combined with the flow from the capillary within the interface to obtain a fluid throughput high enough to maintain a continuous nebulization. Very low detection limits were achieved, 100 ppt for {sup 153}Eu and 125 ppt for {sup 158}Gd. With this optimized CE

  10. Temperature effects on the interaction mechanisms between the europium (III) and uranyl ions and zirconium diphosphate; Effets de la temperature sur les mecanismes d'interaction entre les ions europium (3) et uranyle et le diphosphate de zirconium

    Energy Technology Data Exchange (ETDEWEB)

    Finck, N

    2006-10-15

    Temperature should remain higher than 25 C in the near field environment of a nuclear waste repository for thousands years. In this context, the aim of this work is to study the temperature influence on the interaction mechanisms between europium (III) and uranyl ions and zirconium diphosphate, as well as the influence of a complexing medium (nitrate) on the sorption of the lanthanide. The experimental definition of the equilibria was achieved by combining a structural investigation with the macroscopic sorption data. Surface complexes were characterized at all temperatures (25 C to 90 C) by TRLFS experiments carried out on dry and in situ samples using an oven. This characterization was completed by XPS experiments carried out at 25 C on samples prepared at 25 C and 90 C. The reaction constants (surface hydration and cations sorption) were obtained by simulating the experimental data with the constant capacitance surface complexation model. The reaction constants temperature dependency allowed one to characterize thermodynamically the different reactions by application of the van't Hoff relation. The validity of this law was tested by performing microcalorimetric measurements of the sorption heat for both cations. (author)

  11. Quantum dot based on tin/titanium mixed oxide doped with europium synthesized by protein sol-gel method

    Energy Technology Data Exchange (ETDEWEB)

    Paganini, Paula P.; Felinto, Maria Claudia F.C., E-mail: paulapaganini@usp.b, E-mail: mfelinto@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Brito, Hermi F., E-mail: hefbrito@iq.usp.b [Universidade de Sao Paulo (IQ/USP), Sao Paulo, SP (Brazil). Inst. de Quimica. Lab. de Elementos do Bloco f

    2011-07-01

    Special luminescence biomarkers have been developed to find more sensitive fluoroimmunoassay methods. A new generation of these biomarkers is the semiconductors nanocrystals, known as quantum dots, doped with lanthanides. The use of lanthanides ions as luminescent markers has many advantages, for example a security method, low cost, high specificity and also the luminescence can be promptly measured with high sensibility and accuracy. The protein sol-gel is a modification of conventional method, in which the coconut water replacing the alkoxides normally used. The advantage is that, the proteins present in coconut water bind chemically with metal salts forming a polymer chain. This work presents nanoparticles based on tin/titanium mixed oxide doped with 3% of europium synthesized by protein sol-gel method. The nanoparticles were burned at 300 deg C, 500 deg C, 800 deg C and 1100 deg C. The samples were analyzed and characterized by thermal analysis, X-ray powder diffraction (XRD), infrared spectroscopy (IR) and scanning electron microscopy (SEM). The synthesis was effective and the nanoparticles showed nanometric size and structural differences with the annealing. To be used in the fluoroimmunoassays tests, these particles need to be functionalized before be connect with biological molecules and after this process, these nanoparticles going to be submitted at gamma radiation for sterilization. (author)

  12. 340nm UV LED excitation in time-resolved fluorescence system for europium-based immunoassays detection

    Science.gov (United States)

    Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter; Pedersen, Christian

    2017-02-01

    In immunoassay analyzers for in-vitro diagnostics, Xenon flash lamps have been widely used as excitation light sources. Recent advancements in UV LED technology and its advantages over the flash lamps such as smaller footprint, better wall-plug efficiency, narrow emission spectrum, and no significant afterglow, have made them attractive light sources for gated detection systems. In this paper, we report on the implementation of a 340 nm UV LED based time-resolved fluorescence system based on europium chelate as a fluorescent marker. The system performance was tested with the immunoassay based on the cardiac marker, TnI. The same signal-to-noise ratio as for the flash lamp based system was obtained, operating the LED below specified maximum current. The background counts of the system and its main contributors were measured and analyzed. The background of the system of the LED based unit was improved by 39% compared to that of the Xenon flash lamp based unit, due to the LEDs narrower emission spectrum and longer pulse width. Key parameters of the LED system are discussed to further optimize the signal-to-noise ratio and signal-to-background, and hence the sensitivity of the instrument.

  13. Interaction of europium and nickel with calcite studied by Rutherford Backscattering Spectrometry and Time-Resolved Laser Fluorescence Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Sabau, A. [Agence Nationale pour la gestion des Déchets RAdioactifs, 1-7 rue J. Monnet, Parc de la Croix Blanche, 92298 Châtenay-Malabry Cedex (France); Université de Nice Sophia Antipolis, Ecosystèmes Côtiers Marins et Réponses aux Stress (ECOMERS), 28 avenue Valrose, 06108 Nice Cedex 2 (France); Pipon, Y., E-mail: pipon@ipnl.in2p3.fr [Institut de Physique Nucléaire de Lyon (IPNL), Université Lyon 1, CNRS/IN2P3, 4 rue Enrico Fermi, 69 622 Villeurbanne Cedex (France); Institut Universitaire de Technologie (IUT) Lyon-1, Université Claude Bernard Lyon 1, 69 622 Villeurbanne Cedex (France); Toulhoat, N. [Institut de Physique Nucléaire de Lyon (IPNL), Université Lyon 1, CNRS/IN2P3, 4 rue Enrico Fermi, 69 622 Villeurbanne Cedex (France); CEA/DEN, Saclay, 91191 Gif sur Yvette (France); Lomenech, C. [Université de Nice Sophia Antipolis, Ecosystèmes Côtiers Marins et Réponses aux Stress (ECOMERS), 28 avenue Valrose, 06108 Nice Cedex 2 (France); Jordan, N. [Helmholtz Zentrum Dresden Rossendorf (HZDR), Institute of Resource Ecology (IRE) (Germany); Moncoffre, N. [Institut de Physique Nucléaire de Lyon (IPNL), Université Lyon 1, CNRS/IN2P3, 4 rue Enrico Fermi, 69 622 Villeurbanne Cedex (France); Barkleit, A. [Helmholtz Zentrum Dresden Rossendorf (HZDR), Institute of Resource Ecology (IRE) (Germany); and others

    2014-08-01

    This study aims at elucidating the mechanisms regulating the interaction of Eu and Ni with calcite (CaCO{sub 3}). Calcite powders or single crystals (some mm sized) were put into contact with Eu or Ni solutions at concentrations ranging from 10{sup −3} to 10{sup −5} mol L{sup −1} for Eu and 10{sup −3} mol L{sup −1} for Ni. The sorption durations ranged from 1 week to 1 month. Rutherford Backscattering Spectrometry (RBS) well adapted to discriminate incorporation processes such as: (i) adsorption or co precipitation at the mineral surfaces or, (ii) incorporation into the mineral structure (through diffusion for instance), has been carried out. Moreover, using the fluorescence properties of europium, the results have been compared to those obtained by Time-Resolved Laser Fluorescence Spectroscopy (TRLFS) on calcite powders. For the single crystals, complementary SEM observations of the mineral surfaces at low voltage were also performed. Results showed that Ni accumulates at the calcite surface whereas Eu is also incorporated at a greater depth. Eu seems therefore to be incorporated into two different states in calcite: (i) heterogeneous surface accumulation and (ii) incorporation at depth greater than 160 nm after 1 month of sorption. Ni was found to accumulate at the surface of calcite without incorporation.

  14. Orange-red emitting europium doped strontium ortho-silicate phosphor prepared by a solid state reaction method.

    Science.gov (United States)

    Sahu, Ishwar Prasad

    2017-05-01

    In the present article we report europium-doped strontium ortho-silicates, namely Sr 2 SiO 4 :xEu 3+ (x = 1.0, 1.5, 2.0, 2.5 or 3.0 mol%) phosphors, prepared by solid state reaction method. The crystal structures of the sintered phosphors were consistent with orthorhombic crystallography with a Pmna space group. The chemical compositions of the sintered phosphors were confirmed by energy dispersive X-ray spectroscopy (EDS). Thermoluminescence (TL) kinetic parameters such as activation energy, order of kinetics and frequency factors were calculated by the peak shape method. Orange-red emission originating from the 5 D 0 - 7 F J (J = 0, 1, 2, 3) transitions of Eu 3+ ions could clearly be observed after samples were excited at 395 nm. The combination of these emissions constituted orange-red light as indicated on the Commission Internationale de l'Eclairage (CIE) chromaticity diagram. Mechanoluminescence (ML) intensity of the prepared phosphor increased linearly with increasing impact velocity of the moving piston that suggests that these phosphors can also be used as sensors to detect the stress of an object. Thus, the present investigation indicates that the piezo-electricity was responsible for producing ML in the prepared phosphor. Copyright © 2016 John Wiley & Sons, Ltd.

  15. Application of Europium Multiwalled Carbon Nanotubes as Novel Luminophores in an Electrochemiluminescent Aptasensor for Thrombin Using Multiple Amplification Strategies.

    Science.gov (United States)

    Wu, Dan; Xin, Xia; Pang, Xuehui; Pietraszkiewicz, Marek; Hozyst, Robert; Sun, Xian'ge; Wei, Qin

    2015-06-17

    A novel electrochemiluminescent (ECL) aptasensor was proposed for the determination of thrombin (TB) using exonuclease-catalyzed target recycling and hybridization chain reaction (HCR) to amplify the signal. The capture probe was immobilized on an Au-GS-modified electrode through a Au-S bond. Subsequently, the hybrid between the capture probe and the complementary thrombin binding aptamer (TBA) was aimed at obtaining double-stranded DNA (dsDNA). The interaction between TB and its aptamer led to the dissociation of dsDNA because TB has a higher affinity to TBA than the complementary strands. In the presence of exonuclease, aptamer was selectively digested and TB could be released for target recycling. Extended dsDNA was formed through HCR of the capture probe and two hairpin DNA strands (NH2-DNA1 and NH2-DNA1). Then, numerous europium multiwalled carbon nanotubes (Eu-MWCNTs) could be introduced through amidation reaction between NH2-terminated DNA strands and carboxyl groups on the Eu-MWCNTs, resulting in an increased ECL signal. The multiple amplification strategies, including the amplification of analyte recycling and HCR, and high ECL efficiency of Eu-MWCNTs lead to a wide linear range (1.0×10(-12)-5.0×10(-9) mol/L) and a low detection limit (0.23 pmol/L). The method was applied to serum sample analysis with satisfactory results.

  16. Spectrophotometric Determination and Removal of Unchelated Europium Ions from Solutions Containing Eu-Diethylenetriaminepentaacetic Acid Chelate-Peptide Conjugates1

    Science.gov (United States)

    Dayan Elshan, N. G. R.; Patek, Renata; Vagner, Josef; Mash, Eugene A.

    2014-01-01

    Europium chelates conjugated with peptide ligands are routinely used as probes for conducting in vitro binding experiments. The presence of unchelated Eu ions in these formulations gives high background luminescence and can lead to poor results in binding assays. In our experience, the reported methods for purification of these probes do not achieve adequate removal of unchelated metal ions in a reliable manner. In this work, a xylenol orange-based assay for the quantification of unchelated metal ions was streamlined and used to determine levels of metal ion contamination, as well as the success of metal ion removal upon attempted purification. We compared the use of Empore™ chelating disks and Chelex® 100 resin for the selective removal of unchelated Eu ions from several Eu-diethylenetriaminepentaacetic acid chelate-peptide conjugates. Both purification methods gave complete and selective removal of the contaminant metal ions. However, Empore™ chelating disks were found to give much higher recoveries of the probes under the conditions utilized. Related to the issue of probe recovery, we also describe a significantly more efficient method for the synthesis of one such probe using Rink amide AM resin in place of Tentagel S resin. PMID:25058927

  17. Reusable temperature-sensitive luminescent material based on vitrified film of europium(III) β-diketonate complex

    Science.gov (United States)

    Lapaev, Dmitry V.; Nikiforov, Victor G.; Lobkov, Vladimir S.; Knyazev, Andrey A.; Galyametdinov, Yury G.

    2018-01-01

    We have proposed a novel temperature-sensitive luminescent material which is a 20 μm thick vitrified film (sandwiched between two quartz plates) fabricated from an amorphous powder of a mesogenic europium(III) β-diketonate complex through a melt-processing technique. The film photoexcited by a 337 nm pulsed nitrogen laser displays a typical Eu3+ ion luminescence bands with the strongest peak at 612 nm and with the decay time of 537 μs at 298 K. It is obtained that both the mean luminescence intensity and the luminescence decay time at 612 nm decrease significantly with temperature increasing from 298 to 348 K; the average values of the relative and absolute temperature sensitivities of the luminescence decay time in the range of 298-348 K are -1.2%·K-1 and -6.5 μs·K-1, respectively. The thermal quenching mechanism of the luminescent properties was analyzed and discussed. The experiments showed that, the luminescent properties of the film is insensitive to oxygen, the film is photostable under UV light, there is full reversibility of the temperature-dependent luminescence intensity and the decay time, and the high luminescence brightness of the film can be observed with violet light excitation. These factors indicated that the film is promising material for reusable luminescent thermometers, suitable for long-term monitoring in the range of 298-348 K.

  18. Differential ERK activation during autophagy induced by europium hydroxide nanorods and trehalose: Maximum clearance of huntingtin aggregates through combined treatment.

    Science.gov (United States)

    Wei, Peng-Fei; Jin, Pei-Pei; Barui, Ayan Kumar; Hu, Yi; Zhang, Li; Zhang, Ji-Qian; Shi, Shan-Shan; Zhang, Hou-Rui; Lin, Jun; Zhou, Wei; Zhang, Yun-Jiao; Ruan, Ren-Quan; Patra, Chitta Ranjan; Wen, Long-Ping

    2015-12-01

    Accelerating the clearance of intracellular protein aggregates through elevation of autophagy represents a viable approach for the treatment of neurodegenerative diseases. In our earlier report, we have demonstrated the enhanced degradation of mutant huntingtin protein aggregates through autophagy process induced by europium hydroxide nanorods [EHNs: Eu(III)(OH)3], but the underlying molecular mechanism of EHNs mediated autophagy was unclear. The present report reveals that EHNs induced autophagy does not follow the classical AKT-mTOR and AMPK signaling pathways. The inhibition of ERK1/2 phosphorylation using the specific MEK inhibitor U0126 partially abrogates the autophagy as well as the clearance of mutant huntingtin protein aggregates mediated by EHNs suggesting that nanorods stimulate the activation of MEK/ERK1/2 signaling pathway during autophagy process. In contrast, another mTOR-independent autophagy inducer trehalose has been found to induce autophagy without activating ERK1/2 signaling pathway. Interestingly, the combined treatment of EHNs and trehalose leads to more degradation of mutant huntingtin protein aggregates than that obtained with single treatment of either nanorods or trehalose. Our results demonstrate the rational that further enhanced clearance of intracellular protein aggregates, needed for diverse neurodegenerative diseases, may be achieved through the combined treatment of two or more autophagy inducers, which stimulate autophagy through different signaling pathways. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Synthesis of europium-doped VSOP, customized enhancer solution and improved microscopy fluorescence methodology for unambiguous histological detection.

    Science.gov (United States)

    de Schellenberger, Angela Ariza; Hauptmann, Ralf; Millward, Jason M; Schellenberger, Eyk; Kobayashi, Yuske; Taupitz, Matthias; Infante-Duarte, Carmen; Schnorr, Jörg; Wagner, Susanne

    2017-10-10

    Intrinsic iron in biological tissues frequently precludes unambiguous the identification of iron oxide nanoparticles when iron-based detection methods are used. Here we report the full methodology for synthesizing very small iron oxide nanoparticles (VSOP) doped with europium (Eu) in their iron oxide core (Eu-VSOP) and their unambiguous qualitative and quantitative detection by fluorescence. The resulting Eu-VSOP contained 0.7 to 2.7% Eu relative to iron, which was sufficient for fluorescent detection while not altering other important particle parameters such as size, surface charge, or relaxivity. A customized enhancer solution with high buffer capacity and nearly neutral pH was developed to provide an antenna system that allowed fluorescent detection of Eu-VSOP in cells and histologic tissue slices as well as in solutions even under acidic conditions as frequently obtained from dissolved organic material. This enhancer solution allowed detection of Eu-VSOP using a standard fluorescence spectrophotometer and a fluorescence microscope equipped with a custom filter set with an excitation wavelength (λex) of 338 nm and an emission wavelength (λem) of 616 nm. The fluorescent detection of Eu-doped very small iron oxide nanoparticles (Eu-VSOP) provides a straightforward tool to unambiguously characterize VSOP biodistribution and toxicology at tissue, and cellular levels, providing a sensitive analytical tool to detect Eu-doped IONP in dissolved organ tissue and biological fluids with fluorescence instruments.

  20. Efficient solution-processed double-layer red OLEDs based on a new europium complex with a carbazole group.

    Science.gov (United States)

    Liu, Jian; Miao, Jing-Sheng; Wu, Hong-Bin

    2015-06-01

    A new europium complex EuL3 (Phen) was used as guest dopant, and a blend of Polyvinylcarbazole and 2-(biphenyl-4-yl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PVK and PBD) as host matrix. Efficient red organic light-emitting devices (OLEDs) with double-layer structures were manufactured via a solution-processed technique. The guest-doped levels were 1, 3 and 5 wt% relative to the blend mass, respectively. For the 1 wt% doping-level device, the luminous efficiency and luminance were up to 2.96 cd/A and 635.78 cd/m(2) with emissions from both EuL3 (Phen) and from the host; for the 3 wt% doping-level device, the maximum luminous efficiency and luminance were 1.01 cd/A and 370.91 cd/m(2) for the single emission from EuL3 (Phen) only. Copyright © 2014 John Wiley & Sons, Ltd.

  1. Europium Nanospheres-Based Time-Resolved Fluorescence for Rapid and Ultrasensitive Determination of Total Aflatoxin in Feed.

    Science.gov (United States)

    Wang, Du; Zhang, Zhaowei; Li, Peiwu; Zhang, Qi; Ding, Xiaoxia; Zhang, Wen

    2015-12-02

    Immunochromatographic (IC) assays are considered suitable diagnostic tools for the determination of mycotoxins. A europium nanospheres-based time-resolved fluorescence immunoassay (Eu-Nano-TRFIA), based on a monoclonal antibody and a portable TRFIA reader, was developed to determine total aflatoxin (including aflatoxins B1, B2, G1, and G2) levels in feed samples. Under optimized conditions, the Eu-Nano-TRFIA method detected total aflatoxin within 12 min. It showed good linearity (R(2) > 0.985), LOD of 0.16 μg/kg, a wide dynamic range of 0.48-30.0 μg/kg, recovery rates of 83.9-113.9%, and coefficients of variation (CVs) of 3.5-8.8%. In the 397 samples from company and livestock farms throughout China, the detection rate was 78.3%, concentrations were 0.50-145.30 μg/kg, the highest total aflatoxin content was found in cottonseed meal, and corn was found to be the most commonly contaminated feed. This method could be a powerful alternative for the rapid and ultrasensitive determination of total aflatoxin in quality control and meet the required Chinese maximum residue limits.

  2. Spectrophotometric determination and removal of unchelated europium ions from solutions containing Eu-diethylenetriaminepentaacetic acid chelate-peptide conjugates.

    Science.gov (United States)

    Elshan, N G R Dayan; Patek, Renata; Vagner, Josef; Mash, Eugene A

    2014-11-01

    Europium chelates conjugated with peptide ligands are routinely used as probes for conducting in vitro binding experiments. The presence of unchelated Eu ions in these formulations gives high background luminescence and can lead to poor results in binding assays. In our experience, the reported methods for purification of these probes do not achieve adequate removal of unchelated metal ions in a reliable manner. In this work, a xylenol orange-based assay for the quantification of unchelated metal ions was streamlined and used to determine levels of metal ion contamination as well as the success of metal ion removal on attempted purification. We compared the use of Empore chelating disks and Chelex 100 resin for the selective removal of unchelated Eu ions from several Eu-diethylenetriaminepentaacetic acid chelate-peptide conjugates. Both purification methods gave complete and selective removal of the contaminant metal ions. However, Empore chelating disks were found to give much higher recoveries of the probes under the conditions used. Related to the issue of probe recovery, we also describe a significantly more efficient method for the synthesis of one such probe using Rink amide AM resin in place of Tentagel S resin. Copyright © 2014 Elsevier Inc. All rights reserved.

  3. Formation and structural characterization of a europium(II mono(scorpionate complex and a sterically crowded pyrazabole

    Directory of Open Access Journals (Sweden)

    Phil Liebing

    2017-12-01

    Full Text Available The reaction of EuI2(THF2 with potassium hydrotris(3,5-diisopropylpyrazolylborate (K[HB(3,5-iPr2pz3] (= KTpiPr2, pz = pyrazolyl in a molar ratio of 1:1.5 resulted in extensive ligand fragmentation and formation of the europium(II mono(scorpionate complex bis(3,5-diisopropyl-1H-pyrazole[hydrotris(3,5-diisopropylpyrazolylborato]iodidoeuropium(II, [Eu(C27H46BN6I(C9H16N22] or (TpiPr2(3,5-iPr2pzH2EuIII, 1, in high yield (78%. As a typical by-product, small amounts of the sterically crowded pyrazabole derivative trans-4,8-bis(3,5-diisopropylpyrazol-1-yl-1,3,5,7-tetraisopropylpyrazabole, C36H62B2H8 or trans-{(3,5-iPr2pzHB(μ-3,5-iPr2pz}2, 2, were formed. Both title compounds have been structurally characterized through single-crystal X-ray diffraction. In 1, two isopropyl groups are each disordered over two orientations with occupancy ratios of 0.574 (10:0.426 (10 and 0.719 (16:0.281 (16. In 2, one isopropyl group is similarly disordered, occupancy ratio 0.649 (9:0.351 (9.

  4. Spectrofluorimetric study of the interaction between europium(III) and moxifloxacin in micellar solution and its analytical application

    Science.gov (United States)

    Kamruzzaman, Mohammad; Alam, Al-Mahmnur; Lee, Sang Hak; Ragupathy, Dhanusuraman; Kim, Young Ho; Park, Sang-Ryoul; Kim, Sung Hong

    2012-02-01

    A sensitive spectrofluorimetric method has been developed for the determination of moxifloxacin (MOX) using europium(III)-MOX complex as a fluorescence probe in the presence of an anionic surfactant, sodium dodecyl benzene sulfonate (SDBS). The fluorescence (FL) intensity of Eu 3+ was enhanced by complexation with MOX at 614 nm after excitation at 373 nm. The FL intensity of the Eu 3+-MOX complex was significantly intensified in the presence of SDBS. Under the optimum conditions, it was found that the enhanced FL intensity of the system showed a good linear relationship with the concentration of MOX over the range of 1.8 × 10 -11-7.3 × 10 -9 g mL -1 with a correlation coefficient of 0.9998. The limit of detection of MOX was found to be 2.8 × 10 -12 g mL -1 with relative standard deviation (RSD) of 1.25% for 5 replicate determination of 1.5 × 10 -8 g mL -1 MOX. The proposed method is simple, offers higher sensitivity with wide linear range and can be successfully applied to determine MOX in pharmaceutical and biological samples with good reproducibility. The luminescence mechanism is also discussed in detail with ultraviolet absorption spectra.

  5. Photoluminescence properties of europium doped di-strontium magnesium di-silicate phosphor by solid state reaction method

    Directory of Open Access Journals (Sweden)

    Ishwar Prasad Sahu

    2015-01-01

    Full Text Available Europium doped di-strontium magnesium di-silicate phosphor namely (Sr2MgSi2O7:Eu3+ was prepared by the traditional high temperature solid state reaction method. The phase structure of sintered phosphor was akermanite type structure which belongs to the tetragonal crystallography with space group P42¯1m, this structure is a member of the melilite group and forms a layered compound. The EDX and FTIR spectra confirm the present elements in Sr2MgSi2O7:Eu3+ phosphor. Photoluminescence measurements showed that the phosphor exhibited strong emission peak with good intensity, corresponding to 5D0 → 7F2 (613 nm red emission and weak 5D0 → 7F1 (590 nm orange emission. The excitation spectra monitored at 613 nm show broad band from 220 to 300 nm ascribed to O–Eu charge-transfer band (CTB centered at about 269 nm, and the other peaks in the range of 300–400 nm originated from f–f transitions of Eu3+ ions. The strongest band at 395 nm can be assigned to 7F0 / 5L6 transition of Eu3+ ions due to the typical f–f transitions within Eu3+ of 4f6 configuration.

  6. Highly selective luminescent sensing of picric acid based on a water-stable europium metal-organic framework

    Energy Technology Data Exchange (ETDEWEB)

    Xia, Tifeng; Zhu, Fengliang; Cui, Yuanjing, E-mail: cuiyj@zju.edu.cn; Yang, Yu; Wang, Zhiyu; Qian, Guodong, E-mail: gdqian@zju.edu.cn

    2017-01-15

    A water-stable metal-organic framework (MOF) EuNDC has been synthesized for selective detection of the well-known contaminant and toxicant picric acid (PA) in aqueous solution. Due to the photo-induced electron transfer and self-absorption mechanism, EuNDC displayed rapid, selective and sensitive detection of PA with a detection limit of 37.6 ppb. Recyclability experiments revealed that EuNDC retains its initial luminescent intensity and same quenching efficiency in each cycle, suggesting high photostability and reusability for long-term sensing applications. The excellent detection performance of EuNDC makes it a promising PA sensing material for practical applications. - Graphical abstract: A water-stable europium-based metal-organic framework has been reported for highly selective sensing of picric acid (PA) with a detection limit of 37.6 ppb in aqueous solution. - Highlights: • A water-stable metal-organic framework (MOF) EuNDC was synthesized. • The highly selective detection of picric acid with a detection limit of 37.6 ppb was realized. • The detection mechanism were also presented and discussed.

  7. One-pot carbonization synthesis of europium-doped carbon quantum dots for highly selective detection of tetracycline

    Science.gov (United States)

    Li Liu, Meng; Chen, Bin Bin; Yang, Tong; Wang, Jian; Liu, Xi Dong; Zhi Huang, Cheng

    2017-03-01

    The detection of tetracycline is of great significance because of its damaging effects on human health, such as renal toxicity and hemolytic anemia. Any release of tetracycline into the surrounding environment can produce bacterial drug resistance. We develop a new sensitive and selective detection approach for tetracycline in complex water samples by preparing europium-doped carbon quantum dots (Eu-CQDs) through a simple and rapid carbonization method operating at 200 °C for 5 min. The Eu-CQDs are characterized by blue photoluminescence, excitation-wavelength-dependent emission and excellent stability. Importantly, the fluorescence of the Eu-CQDs can be quenched efficiently by tetracycline, based on the strong inner filter effect mechanism between Eu-CQDs and tetracycline, making the fluorescence intensity ratio (I 0/I) of the Eu-CQDs at 465 nm correlate linearly with the concentration of tetracycline in the range of 0.5-200 μM, with a limit of detection of 0.3 μM. This shows the broad applicability of the Eu-CQDs in pursuing the concepts of simplicity and specificity for analytical purposes.

  8. Mesoporous Europium-Doped Titania Nanoparticles (Eu-MTNs) for Luminescence-Based Intracellular Bio-Imaging.

    Science.gov (United States)

    Chen, Kuan-Chou; Dutta, Saikat; Yamauchi, Yusuke; Alshehri, Saad M; Nguyen, Mai Thanh; Yonezawa, Tetsu; Shen, Kun-Hung; Wu, Kevin C W

    2015-12-01

    Monodisperse and mesoporous europium (Eu)-doped titania nanoparticles (denoted as Eu-MTNs) were prepared by a co-synthesis method with the presence of a cationic surfactant (i.e., CTAB). A maximum loading amount of 8 mol% of Eu could be successfully incorporated into the framework of MTNs. The synthesized Eu-MTNs samples were characterized with X-ray diffraction (XRD) and scanning electron microscopy (SEM), with their luminescent property examined by photoluminescence (PL). Under ultraviolet irradiation, the Eu-MTNs samples exhibit several characteristic luminescence corresponding to 5D0-7F(j) for Eu+3 ions, which can be attributed to the energy transfer from titania nanocrystallite to Eu3+ ions dispersed in amorphous mesoporous titania region. The potential intracellular bio-imaging application of the synthesized Eu-MTN nanoparticles was demonstrated with a breast cancer cell line (i.e., BT-20). High biocompatibility and strong luminescence of the Eu-MTNs show great potential in biomedical applications.

  9. The europium and praseodymium hydrolysis in a 2M NaCl environment; La hidrolisis del europio y del praseodimio en un medio 2M de NaCl

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez R, M.; Lopez G, H.; Solache R, M.; Rojas H, A. [Instituto Nacional de Investigaciones Nucleares, Departamento de quimica, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1998-07-01

    It was studied the europium and praseodymium hydrolysis in a 2M NaCl ion force environment at 303 K, through two methods: this one extraction with dissolvents (lanthanide-water-NaCl-dibenzoylmethane) in presence of a competitive ligand (diglycolic acid) and that one direct potentiometric titration, of soluble species, followed by a computer refining. The values of one or another techniques of the first hydrolysis constants obtained were similar, which demonstrates that the results are reliable. The set of data obtained on the stability constants of hydrolysis products allowed to draw up the distribution diagrams of chemical species, as europium as praseodymium in aqueous environment. (Author)

  10. Specific chiral sensing of amino acids using induced circularly polarized luminescence of bis(diimine)dicarboxylic acid europium(III) complexes.

    Science.gov (United States)

    Okutani, Kazuhiro; Nozaki, Koichi; Iwamura, Munetaka

    2014-06-02

    The circularly polarized luminescence (CPL) from [Eu(pda)2](-) (pda = 1,10-phenanthroline-2,9-dicarboxylic acid) and [Eu(bda)2](-) (bda = 2,2'-bipyridine-6,6'-dicarboxylic acid) in aqueous solutions containing various amino acids was investigated. The europium(III) complexes exhibited bright-red luminescence assignable to the f-f transition of the Eu(III) ion when irradiated with UV light. Although the luminescence was not circularly polarized in the solid state or in aqueous solutions, in accordance with the achiral crystal structure, the complexes exhibited detectable induced CPL (iCPL) in aqueous solutions containing chiral amino acids. In the presence of L-pyrrolidonecarboxylic acid, both [Eu(pda)2](-) and [Eu(bda)2](-) showed similar iCPL intensity (glum ∼ 0.03 for the (5)D0 → (7)F1 transition at 1 mol·dm(-3) of the amino acid). On the other hand, in the presence of L-histidine or L-arginine, [Eu(pda)2](-) exhibited intense CPL (glum ∼ 0.08 for the (5)D0 → (7)F1 transition at 0.10 mol·dm(-3) of the amino acid), whereas quite weak CPL was observed for [Eu(bda)2](-) under the same conditions (glum europium(III) complexes possess coordination structures similar to that in the crystal with slight distortion to form a chiral structure due to specific interaction with two zwitterionic amino acids. This mechanism was in stark contrast to that of the europium(III) complex-pyrrolidonecarboxylic acid system in which one amino acid coordinates to the Eu(III) ion to yield an achiral coordination structure.

  11. A convenient method for europium-labeling of a recombinant chimeric relaxin family peptide R3/I5 for receptor-binding assays.

    Science.gov (United States)

    Zhang, Wei-Jie; Jiang, Qian; Wang, Xin-Yi; Song, Ge; Shao, Xiao-Xia; Guo, Zhan-Yun

    2013-06-01

    Relaxin family peptides have important biological functions, and so far, four G-protein-coupled receptors have been identified as their receptors (RXFP1-4). A chimeric relaxin family peptide R3/I5, containing the B-chain of relaxin-3 and the A-chain of INSL5, is a selective agonist for both RXFP3 and RXFP4. In a previous study, europium-labeled R3/I5, as a nonradioactive and low-background receptor-binding tracer, was prepared through a chemical synthesis approach. In the present study, we established a convenient alternative approach for preparing the europium-labeled R3/I5 tracer based on a recombinant R3/I5 designed to carry a solubilizing tag at the A-chain N-terminus and a pyroglutamate residue at the B-chain N-terminus. Because of the presence of a single primary amine moiety, the recombinant R3/I5 peptide was site-specifically mono-labeled at the A-chain N-terminus by a diethylenetriaminepentaacetic acid/europium moiety through a convenient one-step procedure. The diethylenetriaminepentaacetic acid/Eu3+-labeled R3/I5 bound both receptors RXFP3 and RXFP4 with high binding affinities and low nonspecific binding. Thus, we have presented a valuable nonradioactive tracer for future interaction studies on RXFP3 and RXFP4 with various natural or designed ligands. The present approach could also be adapted for preparing and labeling of other chimeric relaxin family peptides. Copyright © 2013 European Peptide Society and John Wiley & Sons, Ltd.

  12. Europium-activated phosphors containing oxides of rare-earth and group-IIIB metals and method of making the same

    Science.gov (United States)

    Comanzo, Holly Ann; Setlur, Anant Achyut; Srivastava, Alok Mani; Manivannan, Venkatesan

    2004-07-13

    Europium-activated phosphors comprise oxides of at least a rare-earth metal selected from the group consisting of gadolinium, yttrium, lanthanum, and combinations thereof and at least a Group-IIIB metal selected from the group consisting of aluminum, gallium, indium, and combinations thereof. A method for making such phosphors comprises adding at least a halide of at least one of the selected Group-IIIB metals in a starting mixture. The method further comprises firing the starting mixture in an oxygen-containing atmosphere. The phosphors produced by such a method exhibit improved absorption in the UV wavelength range and improved quantum efficiency.

  13. Synthesis and pharmacological characterization of a europium-labelled single-chain antagonist for binding studies of the relaxin-3 receptor RXFP3.

    Science.gov (United States)

    Haugaard-Kedström, Linda M; Wong, Lilian L L; Bathgate, Ross A D; Rosengren, K Johan

    2015-06-01

    Relaxin-3 and its endogenous receptor RXFP3 are involved in fundamental neurological signalling pathways, such as learning and memory, stress, feeding and addictive behaviour. Consequently, this signalling system has emerged as an attractive drug target. Development of leads targeting RXFP3 relies on assays for screening and ligand optimization. Here, we present the synthesis and in vitro characterization of a fluorescent europium-labelled antagonist of RXFP3. This ligand represents a cheap and safe but powerful tool for future mechanistic and cell-based receptor-ligand interaction studies of the RXFP3 receptor.

  14. Bis{[6-methoxy-2-(4-methylphenyliminiomethyl]phenolate-κ2O,O′}tris(nitrato-κ2O,O′europium(III

    Directory of Open Access Journals (Sweden)

    Hang-Ming Guo

    2010-11-01

    Full Text Available The crystal structure of title compound, [Eu(NO33(C15H15NO22], contains two Schiff base 6-methoxy-2-[(4-methylphenyliminomethyl]phenolate (L ligands and three independent nitrate ions that chelate to the europium(III ion via the O atoms. The coordination number of the EuIII ion is ten. The L ligands chelate with a strong Eu—O(deprotonated phenolate bond and a weak Eu—O(methoxy contact, the latter can be interpreted as the apices of the bicapped square-antiprismatic EuIII polyhedron. Intramolecular N—H...O hydrogen bonds occur.

  15. Carbon footprint assessment of recycling technologies for rare earth elements: A case study of recycling yttrium and europium from phosphor.

    Science.gov (United States)

    Hu, Allen H; Kuo, Chien-Hung; Huang, Lance H; Su, Chao-Chin

    2017-02-01

    Rare earth elements are key raw materials in high-technology industries. Mining activities and manufacturing processes of such industries have caused considerable environmental impacts, such as soil erosion, vegetation destruction, and various forms of pollution. Sustaining the long-term supply of rare earth elements is difficult because of the global shortage of rare earth resources. The diminishing supply of rare earth elements has attracted considerable concern because many industrialized countries regarded such elements as important strategic resources for economic growth. This study aims to explore the carbon footprints of yttrium and europium recovery techniques from phosphor. Two extraction recovery methods, namely, acid extraction and solvent extraction, were selected for the analysis and comparison of carbon footprints. The two following functional units were used: (1) the same phosphor amounts for specific Y and Eu recovery concentrations, and (2) the same phosphor amounts for extraction. For acid extraction method, two acidic solutions (H2SO4 and HCl) were used at two different temperatures (60 and 90°C). For solvent extraction method, acid leaching was performed followed by ionic liquid extraction. Carbon footprints from acid and solvent extraction methods were estimated to be 10.1 and 10.6kgCO2eq, respectively. Comparison of the carbon emissions of the two extraction methods shows that the solvent extraction method has significantly higher extraction efficiency, even though acid extraction method has a lower carbon footprint. These results may be used to develop strategies for life cycle management of rare earth resources to realize sustainable usage. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Europium doped di-calcium magnesium di-silicate orange–red emitting phosphor by solid state reaction method

    Directory of Open Access Journals (Sweden)

    Ishwar Prasad Sahu

    2015-07-01

    Full Text Available A new orange–red europium doped di-calcium magnesium di-silicate (Ca2MgSi2O7:Eu3+ phosphor was prepared by the traditional high temperature solid state reaction method. The prepared Ca2MgSi2O7:Eu3+ phosphor was characterized by X-ray diffractometer (XRD, transmission electron microscopy (TEM, field emission scanning electron microscopy (FESEM with energy dispersive x-ray spectroscopy (EDX, fourier transform infrared spectra (FTIR, photoluminescence (PL and decay characteristics. The phase structure of sintered phosphor was akermanite type structure which belongs to the tetragonal crystallography with space group P4¯21m, this structure is a member of the melilite group and forms a layered compound. The chemical composition of the sintered Ca2MgSi2O7:Eu3+ phosphor was confirmed by EDX spectra. The PL spectra indicate that Ca2MgSi2O7:Eu3+ can be excited effectively by near ultraviolet (NUV light and exhibit bright orange–red emission with excellent color stability. The fluorescence lifetime of Ca2MgSi2O7:Eu3+ phosphor was found to be 28.47 ms. CIE color coordinates of Ca2MgSi2O7:Eu3+ phosphor is suitable as orange-red light emitting phosphor with a CIE value of (X = 0.5554, Y = 0.4397. Therefore, it is considered to be a new promising orange–red emitting phosphor for white light emitting diode (LED application.

  17. Evaluation of in vivo cytogenetic toxicity of europium hydroxide nanorods (EHNs) in male and female Swiss albino mice.

    Science.gov (United States)

    Bollu, Vishnu Sravan; Nethi, Susheel Kumar; Dasari, Rama Krishna; Rao, Soma Shiva Nageshwara; Misra, Sunil; Patra, Chitta Ranjan

    2016-01-01

    Our group already demonstrated that europium hydroxide nanorods (EHNs) show none or mild toxicity in C57BL/6 mice even at high dose and exhibited excellent pro-angiogenic activity towards in vitro and in vivo models. In the present study, we evaluated the in vivo cytogenetic toxicity of intraperitoneally administered EHNs (12.5-250 mg/kg/b.w.) in male and female Swiss albino mice by analyzing chromosomal aberrations (CAs), mitotic index (MI), micronucleus (MN) from bone marrow and peripheral blood. Furthermore, we performed the cytogenetic toxicity study of EHNs towards Chinese hamster ovary (CHO) cells, in order to compare with the in vivo results. The results of CA assay of mice treated with EHNs (12.5-125 mg/kg/b.w.) showed no significant change in the formation of aberrant metaphases compared to the control group. Also, there was no significant difference in the number of dividing cells between the control group and EHNs-treated groups observed by MI study, suggesting the non-cytotoxicity of EHNs. Additionally, FACS study revealed that EHNs do not arrest cells at any phase of cell cycle in the mouse model. Furthermore, MN test of both bone marrow and peripheral blood showed no significant differences in the induction of MNs when compared with the control group. In vitro results from CHO cells also support our in vivo observations. Considering the role of angiogenesis by EHNs and the absence of its genotoxicity in mouse model, we strongly believe the future application of EHNs in treating various diseases, where angiogenesis plays an important role such as cardiovascular diseases, ischemic diseases and wound healing.

  18. First-principles study of structural stability, elastic and electronic properties of ternary rare earth-transition metal—Borides and carbides (RT{sub x}Z, R=Sc, Y, and La, T=Pt and Pd, Z=B and C, and x=2, 3, and 4)

    Energy Technology Data Exchange (ETDEWEB)

    Yao, Tiankai; Wang, Yachun; Li, Hui [Key Laboratory of Metastable Materials Science and Technology, College of Material Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Lian, Jie [Department of Mechanical, Aerospace and Nuclear Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Zhang, Jingwu, E-mail: zjw@ysu.edu.cn [Key Laboratory of Metastable Materials Science and Technology, College of Material Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Gou, Huiyang, E-mail: huiyang.gou@gmail.com [Key Laboratory of Metastable Materials Science and Technology, College of Material Science and Engineering, Yanshan University, Qinhuangdao 066004 (China)

    2013-12-15

    Using first-principles total energy calculations (CASTEP code), the structural stability, elastic, and electronic properties of ternary rare earth-transition metal borides and carbides (RT{sub x}Z, R=Sc, Y, and La, T=Pt and Pd, Z=B and C, and x=2, 3, and 4) compounds were studied. Results show that RT{sub 3}Z compounds with tetragonal P4mm structure are energetically more favorable than usually cubic perovskite-type structure. Furthermore, RT{sub 3}Z with perovskite structure is found to be mechanically unstable with the negative C{sub 44}. Formation enthalpy calculations indicate that Pt-based borides are easier to be synthesized compared with Pd-based ones and counterpart carbides, respectively. Elastic constants, bulk moduli, shear moduli, Young's moduli, and Poisson's ratio of studied compounds have been calculated. Also, all the studied compounds show ductile behavior. Moreover, total and partial density of states (DOSs) and bonding charge density were employed to elucidate the bonding features of these compounds. The results reveal that the covalency between Pt-5d and Z-2p as well as T-nd (n=4 for Pd and 5 for Pt) and B-2p states, are the cause of the relatively higher elastic moduli of Pt-based compounds and R–T-borides, respectively.

  19. Synthesis, characterization, crystal structure, DNA/BSA binding ability and antibacterial activity of asymmetric europium complex based on 1,10- phenanthroline

    Science.gov (United States)

    Alfi, Nafiseh; Khorasani-Motlagh, Mozhgan; Rezvani, Ali Reza; Noroozifar, Meissam; Molčanov, Krešimir

    2017-06-01

    A heteroleptic europium coordination compound formulated as [Eu(phen)2(OH2)2(Cl)2](Cl)(H2O) (phen = 1,10-phenanthroline), has been synthesized and characterized by elemental analysis, FT-IR spectroscopy, and single-crystal X-ray diffractometer. Crystal structure analysis reveals the complex is crystallized in orthorhombic system with Pca21 space group. Electronic absorption and various emission methods for investigation of the binding system of europium(III) complex to Fish Salmon deoxyribonucleic acid (FS-DNA) and Bovamin Serum Albumin (BSA) have been explored. Furthermore, the binding constants, binding sites and the corresponding thermodynamic parameters of the interaction system based on the van't Hoff equation for FS-DNA and BSA were calculated. The thermodynamic parameters reflect the exothermic nature of emission process (ΔH°DNA by non-intercalative mode which the groove binding is preferable mode. Also, the complex exhibits a brilliant antimicrobial activity in vitro against standard bacterial strains.

  20. Investigation on the co-luminescence effect of europium (III)-lanthanum(III)-dopamine-sodium dodecylbenzene sulfonate system and its application.

    Science.gov (United States)

    Si, Hailin; Zhao, Fang; Cai, Huan

    2013-01-01

    A novel luminescence, enhancement phenomenon in the europium(III)-dopamine-sodium dodecylbenzene sulfonate system was observed when lanthanum(III) was added. Based on this, a sensitive co-luminescence method was established for the determination of dopamine. The luminescence signal for the europium (III)-lanthanum(III)-dopamine-sodium dodecylbenzene sulfonate system was monitored at λ(ex) = 300 nm, λ(em) = 618 nm and pH 8.3. Under optimized conditions, the enhanced luminescence signal responded linearly to the concentration of dopamine in the range 1.0 × 10(-10)-5.0 × 10(-7) mol/L with a correlation coefficient of 0.9993 (n = 11). The detection limit (3σ) was 2.7 × 10(-11) mol/L and the relative standard deviation for 11 parallel measurements of 3.0 × 10(-8) mol/L dopamine was 1.9%. The presented method was successfully applied for the estimation of dopamine in samples of pharmaceutical preparations, human serum and urine. The possible luminescence enhancement mechanism of the system is discussed briefly. Copyright © 2013 John Wiley & Sons, Ltd.

  1. Europium-phenolic network coated BaGdF5 nanocomposites for tri-modal computed tomography/magnetic resonance/luminescence imaging.

    Science.gov (United States)

    Zhu, Wei; Liang, Shuang; Wang, Jing; Yang, Zhe; Zhang, Li; Yuan, Tianmeng; Xu, Zushun; Xu, Haibo; Li, Penghui

    2017-05-01

    Multifunctional nanocomposites based on BaGdF5 nanoparticles (NPs) and metal phenolic network (MPN) have been engineered as novel contrast agents for potential applications in X-ray computed tomography, magnetic resonance and luminescence imaging. The BaGdF5@MPN nanocomposites were synthesized at room temperature by coating BaGdF5 NPs with europium-phenolic network, which was obtained by the coordination of europium (III) with tannic acid (TA). The in vitro cytotoxicity assays against HepG2 cells revealed that the BaGdF5@MPN nanocomposites presented better cytocompatibility and lower cytotoxity than pure BaGdF5 NPs. In addition, vivid red and green luminescence can be observed by confocal laser scanning microscope (CLSM) from the BaGdF5@MPN nanocomposites laden HepG2 cells under the excitation of UV (390 nm) and visible light (440 nm), respectively. The longitudinal relaxivity value (r1) of the nanocomposites was 2.457 mM-1s-1. Moreover, the nanocomoposites exhibited X-ray computed tomography (CT) and T1-weighted magnetic resonance (MR) imaging capacities, and the intensities of the enhanced signals of in vitro CT and MR images were proportional to the concentrations of the nanocomposites. These results indicated that the as-prepared BaGdF5@MPN nanocomposites are promising contrast agents for CT/MR/luminescence imaging.

  2. Effective visible light-active boron and europium co-doped BiVO4 synthesized by sol-gel method for photodegradion of methyl orange.

    Science.gov (United States)

    Wang, Min; Che, Yinsheng; Niu, Chao; Dang, Mingyan; Dong, Duo

    2013-11-15

    Eu-B co-doped BiVO4 visible-light-driven photocatalysts have been synthesized using the sol-gel method. The resulting materials were characterized by a series of joint techniques, including XPS, XRD, SEM, BET, and UV-vis DRS analyses. Compared with BiVO4 and B-BiVO4 photocatalysts, the Eu-B-BiVO4 photocatalysts exhibited much higher photocatalytic activity for methyl orange (MO) degradation under visible light irradiation. The optimal Eu doping content is 0.8 mol%. It was revealed that boron and europium were doped into the lattice of BiVO4 and this led to more surface oxygen vacancies, high specific surface areas, small crystallite size, a narrower band gap and intense light absorbance in the visible region. The doped Eu(III) cations can help in the separation of photogenerated electrons. The synergistic effects of boron and europium in doped BiVO4 were the main reason for improving visible light photocatalytic activity. Copyright © 2013 Elsevier B.V. All rights reserved.

  3. Emission tunability and local environment in europium-doped OH{sup −}-free calcium aluminosilicate glasses for artificial lighting applications

    Energy Technology Data Exchange (ETDEWEB)

    Farias, Aline M.; Sandrini, Marcelo; Viana, José Renato M.; Baesso, Mauro L.; Bento, Antônio C.; Rohling, Jurandir H. [Departamento de Física, Universidade Estadual de Maringá, Av Colombo, 5790, 87020-900, Maringá, PR (Brazil); Guyot, Yannick [Laboratoire de Physico–Chimie des Matériaux Luminescents, Université de Lyon, Université Claude Bernard Lyon 1, Villeurbanne, UMR 5620 CNRS 69622 (France); De Ligny, Dominique [Department of Materials Science and Engineering, University of Erlangen Nürnberg, Martens str. 5, 91058, Erlangen (Germany); Nunes, Luiz Antônio O. [Instituto de Física de São Carlos, Universidade de São Paulo, Av. Trabalhador São-Carlense400, 13566-590, São Carlos, SP (Brazil); Gandra, Flávio G. [Instituto de Física Gleb Wataghin, Universidade Estadual de Campinas, 13083-859, Campinas, SP (Brazil); Sampaio, Juraci A. [Lab Ciências Físicas, Universidade Estadual Norte Fluminense, 28013-602, Campos Dos Goytacazes, RJ (Brazil); Lima, Sandro M.; Andrade, Luis Humberto C. [Grupo de Espectroscopia Óptica e Fototérmica, Universidade Estadual de Mato Grosso do Sul-UEMS, Dourados, MS, C. P. 351, CEP 79804-970 (Brazil); and others

    2015-04-15

    The relationship between emission tunability and the local environment of europium ions in OH{sup −}-free calcium aluminosilicate glasses was investigated, focusing on the development of devices for artificial lighting. Significant conversion of Eu{sup 3+} to Eu{sup 2+} was obtained by means of melting the glasses under a vacuum atmosphere and controlling the silica content, resulting in broad, intense, and tunable luminescence ranging from blue to red. Electron spin resonance and X-ray absorption near edge structure measurements enabled correlation of the luminescence behavior of the material with the Eu{sup 2+}/Eu{sup 3+} concentration ratio and changes in the surrounding ions' crystal field. The coordinates of the CIE 1931 chromaticity diagram were calculated from the spectra, and the contour maps showed that the light emitted from Eu{sup 2+} presented broad bands and enhanced color tuning, ranging from reddish-orange to blue. The results showed that these Eu doped glasses can be used for tunable white lighting by combining matrix composition and the adjustment of the pumping wavelength. - Highlights: • Eu{sup 2+}-doped OH{sup −} free calcium aluminosilicate glass as a new source for white lighting. • Correlation between emission tunability and local environment of europium ions. • Significant reduction of Eu{sup 3+} to Eu{sup 2+} by melting the glasses under vacuum atmosphere. • Broad, intense and tunable luminescence ranging from blue to red.

  4. Determination of the hydrolysis constants of Europium (III), in ion strength media 4, 5 and 6 M NaClO{sub 4} at 303 K; Determinacion de las constantes de hidrolisis del Europio (III), en medios de fuerza ionica 4, 5 y 6 M de NaClO{sub 4} a 303 K

    Energy Technology Data Exchange (ETDEWEB)

    Alvarado B, A.; Jimenez R, M.; Solache R, M. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1999-07-01

    This work was made with the purpose to complete information about the hydrolysis constants of Europium (III) in high ion strength media. So it was determined at a ion forces media 4, 5 and 6 M of sodium perchlorate at 303 K. The method used was the potentiometric with the aid of the Super quad computer program. In high ion strength media, the measurements of p H do not correspond directly to negative logarithm of the concentration of hydrogen ions, by this it is necessary to calibrate the electrode in these conditions. The Europium was hydrolized at pC{sub H} values greater 6 in all cases. The potentiometric method used under the described experimental conditions is adequate to determine the hydrolysis constants of Europium (III). According to the results and diagrams of chemical species of Europium obtained we can conclude that the hydrolysis constants, differ by its distribution but not in its identity. (Author)

  5. The Level of Europium-154 Contaminating Samarium-153-EDTMP Activates the Radiation Alarm System at the US Homeland Security Checkpoints

    Directory of Open Access Journals (Sweden)

    Mohammed Najeeb Al Hallak

    2009-08-01

    Full Text Available 153Sm-EDTMP is a radiopharmaceutical composed of EDTMP (ethylenediamine-tetramethylenephosphonate and Samarium-153 [1]. 153Sm-EDTMP has an affinity for skeletal tissue and concentrates in areas with increased bone turnover; thus, it is successfully used in relieving pain related to diffuse bone metastases [1]. The manufacturing process of 153Sm-EDTMP leads to contamination with 154Eu (Europium-154 [2]. A previous study only alluded to the retention of 154Eu in the bones after receiving treatment with 153Sm-EDTMP [2]. Activation of the alarm at security checkpoints after 153Sm-EDTMP therapy has not been previously reported. Two out of 15 patients who received 153Sm-EDTMP at Roger Maris Cancer Center (Fargo, N. Dak., USA activated the radiation activity sensors while passing through checkpoints; one at a US airport and the other while crossing theAmerican-Canadian border. We assume that the 154Eu which remained in the patients’ bones activated the sensors. Methods: In order to investigate this hypothesis, we obtained the consent from 3 of our 15 patients who received 153Sm-EDTMP within the previous 4 months to 2 years, including the patient who had activated the radiation alarm at the airport. The patients were scanned with a handheld detector and a gamma camera for energies from 511 keV to 1.3 MeV. Results: All three patients exhibited identical spectral images, and further analysis showed that the observed spectra are the result of 154Eu emissions. Conclusion: Depending on the detection thresholds and windows used by local and federal authorities, the remaining activity of 154Eu retained in patients who received 153Sm-EDTMP could be sufficient enough to increase the count rates above background levels and activate the sensors. At Roger Maris Cancer Center, patients are now informed of the potential consequences of 153Sm-EDTMP therapy prior to initiating treatment. In addition, patients treated with 153Sm-EDTMP at Roger Maris Cancer Center

  6. Europium-Labeled Synthetic C3a Protein as a Novel Fluorescent Probe for Human Complement C3a Receptor.

    Science.gov (United States)

    Dantas de Araujo, Aline; Wu, Chongyang; Wu, Kai-Chen; Reid, Robert C; Durek, Thomas; Lim, Junxian; Fairlie, David P

    2017-06-21

    Measuring ligand affinity for a G protein-coupled receptor is often a crucial step in drug discovery. It has been traditionally determined by binding putative new ligands in competition with native ligand labeled with a radioisotope of finite lifetime. Competing instead with a lanthanide-based fluorescent ligand is more attractive due to greater longevity, stability, and safety. Here, we have chemically synthesized the 77 residue human C3a protein and conjugated its N-terminus to europium diethylenetriaminepentaacetate to produce a novel fluorescent protein (Eu-DTPA-hC3a). Time-resolved fluorescence analysis has demonstrated that Eu-DTPA-hC3a binds selectively to its cognate G protein-coupled receptor C3aR with full agonist activity and similar potency and selectivity as native C3a in inducing calcium mobilization and phosphorylation of extracellular signal-regulated kinases in HEK293 cells that stably expressed C3aR. Time-resolved fluorescence analysis for saturation and competitive binding gave a dissociation constant (Kd) of 8.7 ± 1.4 nM for Eu-DTPA-hC3a and binding affinities for hC3a (pKi of 8.6 ± 0.2 and Ki of 2.5 nM) and C3aR ligands TR16 (pKi of 6.8 ± 0.1 and Ki of 138 nM), BR103 (pKi of 6.7 ± 0.1 and Ki of 185 nM), BR111 (pKi of 6.3 ± 0.2 and Ki of 544 nM) and SB290157 (pKi of 6.3 ± 0.1 and Ki of 517 nM) via displacement of Eu-DTPA-hC3a from hC3aR. The macromolecular conjugate Eu-DTPA-hC3a is a novel nonradioactive probe suitable for studying ligand-C3aR interactions with potential value in accelerating drug development for human C3aR in physiology and disease.

  7. The Level of Europium-154 Contaminating Samarium-153-EDTMP Activates the Radiation Alarm System at the US Homeland Security Checkpoints.

    Science.gov (United States)

    Najeeb Al Hallak, Mohammed; McCurdy, Matt; Zouain, Nicolas; Hayes, Justin

    2009-08-28

    (153)Sm-EDTMP is a radiopharmaceutical composed of EDTMP (ethylenediamine-tetramethylenephosphonate) and Samarium-153 [1]. (153)Sm-EDTMP has an affinity for skeletal tissue and concentrates in areas with increased bone turnover; thus, it is successfully used in relieving pain related to diffuse bone metastases [1]. The manufacturing process of (153)Sm-EDTMP leads to contamination with (154)Eu (Europium-154) [2]. A previous study only alluded to the retention of (154)Eu in the bones after receiving treatment with (153)Sm-EDTMP [2]. Activation of the alarm at security checkpoints after (153)Sm-EDTMP therapy has not been previously reported. Two out of 15 patients who received (153)Sm-EDTMP at Roger Maris Cancer Center (Fargo, N. Dak., USA) activated the radiation activity sensors while passing through checkpoints; one at a US airport and the other while crossing the American-Canadian border. We assume that the (154)Eu which remained in the patients' bones activated the sensors. METHODS: In order to investigate this hypothesis, we obtained the consent from 3 of our 15 patients who received (153)Sm-EDTMP within the previous 4 months to 2 years, including the patient who had activated the radiation alarm at the airport. The patients were scanned with a handheld detector and a gamma camera for energies from 511 keV to 1.3 MeV. RESULTS: All three patients exhibited identical spectral images, and further analysis showed that the observed spectra are the result of (154)Eu emissions. CONCLUSION: Depending on the detection thresholds and windows used by local and federal authorities, the remaining activity of (154)Eu retained in patients who received (153)Sm-EDTMP could be sufficient enough to increase the count rates above background levels and activate the sensors. At Roger Maris Cancer Center, patients are now informed of the potential consequences of (153)Sm-EDTMP therapy prior to initiating treatment. In addition, patients treated with (153)Sm-EDTMP at Roger Maris Cancer

  8. Crystal Growth, Structures, and Properties of the Complex Borides, LaOs 2 Al 2 B and La 2 Os 2 AlB 2

    Energy Technology Data Exchange (ETDEWEB)

    Bugaris, Daniel E.; Han, Fei; Im, Jino; Chung, Duck Young; Freeman, Arthur J.; Kanatzidis, Mercouri G.

    2015-08-17

    Single crystals of two novel quaternary metal borides, LaOs2Al2B and La2Os2AlB2, have been grown from La/Ni eutectic fluxes. LaOs2Al2B crystallizes in tetragonal space group P4/mmm with the CeCr2Si2C-type structure, and lattice parameters a = 4.2075(6) angstrom and c = 5.634(1) angstrom. La2Os2AlB2 exhibits a new crystal structure in monoclinic space group C2/c with lattice parameters a = 16.629(3) angstrom, b = 6.048(1) angstrom, c = 10.393(2) angstrom, and beta = 113.96(3)degrees. Both structures are three-dimensional frameworks with unusual coordination (for solid-state compounds) of the boron atoms by transition metal atoms. The boron atom is square planar in LaOs2Al2B, whereas it exhibits linear and T-shaped geometries in La2Os2AlB2. Electrical resistivity measurements reveal poor metal behavior (rho(30)0 (K) similar to 900 mu Omega cm) for La2Os2AlB2, consistent with the electronic band structure calculations, which also predict a metallic character for LaOs2Al2B.

  9. Neutron cross section evaluations of europium isotopes in 1 keV - 30 MeV energy range. Format - validation - comparison; Evaluation de sections efficaces pour des neutrons incidents sur des isotopes d'europium aux energies 1 keV - 30 MeV. Format - validation - comparaison

    Energy Technology Data Exchange (ETDEWEB)

    Dossantos-Uzarralde, P.; Le Luel, C.; Bauge, E. [CEA Bruyeres le Chatel, 91 (France). Dept. de Physique Theorique et Appliquee

    2004-07-01

    This paper presents neutron cross section evaluations of Europium isotopes. The cross sections are evaluated in 1 keV - 30 MeV energy range for the isotopes {sup 146}Eu, {sup 147}Eu, {sup 148}Eu, {sup 149}Eu, {sup 150}Eu, {sup 151}Eu, {sup 152}Eu, {sup 153}Eu, {sup 154}Eu in their ground state. This evaluation includes cross section productions of the long life isomeric states. Special attention is put on the options used for the description of the files written in ENDF-6 format. The final issue is a proposal of a new breed of ENDF-6 formatted neutron activation file. (authors)

  10. Complexation of lactate with neodymium(III) and europium(III) at variable temperatures: studies by potentiometry, microcalorimetry, optical absorption, and luminescence spectroscopy.

    Science.gov (United States)

    Tian, Guoxin; Martin, Leigh R; Rao, Linfeng

    2010-11-15

    The complexation of neodymium(III) and europium(III) with lactate was studied at variable temperatures by potentiometry, absorption spectrophotometry, luminescence spectroscopy, and microcalorimetry. The stability constants of three successive lactate complexes (ML(2+), ML(2)(+), and ML(3)(aq), where M stands for Nd and Eu and L stands for lactate) at 10, 25, 40, 55, and 70 °C were determined. The enthalpies of complexation at 25 °C were determined by microcalorimetry. Thermodynamic data show that the complexation of trivalent lanthanides (Nd(3+) and Eu(3+)) with lactate is exothermic and the complexation becomes weaker at higher temperatures. Results from optical absorption and luminescence spectroscopy suggest that the complexes are inner-sphere chelate complexes in which the protonated α-hydroxyl group of lactate participates in the complexation.

  11. Selective separation of americium from europium using 2,9-bis(triazine)-1,10-phenanthrolines in ionic liquids: a new twist on an old story.

    Science.gov (United States)

    Williams, Neil J; Dehaudt, Jérémy; Bryantsev, Vyacheslav S; Luo, Huimin; Abney, Carter W; Dai, Sheng

    2017-02-28

    Bis-triazine phenanthrolines have shown great promise for f-block metal separations, attributable to their highly preorganized structure, nitrogen donors, and more enhanced covalent bonding with actinides over lanthanides. However, their limited solubility in traditional solvents remains a technological bottleneck. Herein we report our recent work using a simple 2,9-bis(triazine)-1,10-phenanthroline (Me-BTPhen) dissolved in an ionic liquid (IL), demonstrating the efficacy of IL extraction systems for the selective separation of americium from europium, achieving separation factors in excess of 7500 and selectively removing up to 99% of the americium. Characterization of the coordination environment was performed using a combination of X-ray absorption fine structure spectroscopy (XAFS) and density functional theory (DFT) calculations.

  12. Experimental and Theoretical Studies on the Structure and Photoluminescent Properties of New Mononuclear and Homodinuclear Europium(III β-Diketonate Complexes

    Directory of Open Access Journals (Sweden)

    João P. Martins

    2015-01-01

    Full Text Available Two novel europium(III complexes, a monomer and a homodimer, with 1-(4-chlorophenyl-4,4,4-trifluoro-1,3-butanedione (Hcbtfa and 5-chloro-1,10-phenanthroline (cphen ligands, formulated as [Eu(cbtfa3(cphen] and [Eu2(cbtfa4(cphen2(CH3O2], have been synthesized. Their structures have been elucidated by X-ray diffraction and their absorption and emission properties have been studied in the solid state. The experimental data has then been used to test the recently released LUMPAC software, a promising tool which can facilitate the design of more efficient lanthanide light-conversion molecular devices by combining ground state geometry, excited state energy, and luminescent properties calculations.

  13. Optical Temperature Probe Based on the Fluorescence Decay Time of Tris-(dibenzoylmethane mono (5-amino-1,10-phenanthroline-europium(III

    Directory of Open Access Journals (Sweden)

    Hung T. LAM

    2010-08-01

    Full Text Available The measurement of temperature is essential in defining the physical and chemical properties of any system. This is particularly true in dynamic systems where the temperature may fluctuate during the process. In this paper we investigated the potential of tris-(dibenzoylmethane mono (5-amino-1, 10-phenanthroline-europium(III ( Eu[tdap] as an optical temperature probe. The principle of the measurement is based on the temperature dependence of the fluorescence decay time of Eu(tdap embedded in polystyrene. Within the investigated temperature range between 3 and 70°C a linear correlation between temperature and decay time was found. The probe is accurate and repeatable and there is no cross-sensitivity to pH changes. Continuous measurement for more than 2.5 hours at which the temperature is switched between two different temperatures shows no signal drift. The relative standard deviation is less than 0.65 percent.

  14. Crystal structure and luminescence of a europium coordination polymer {[Eu( m-MOBA) 3·2H 2O]1/2(4,4'-bpy)} ∞

    Science.gov (United States)

    Li, X.; Zheng, X.; Jin, L.; Lu, S.; Qin, W.

    2000-02-01

    The structure of the complex [Eu( m-MOBA) 3·2H 2O]1/2(4,4'-bpy) ( m-MOBA: m-methoxybenzoate, 4,4'-bpy: 4,4'-bipyridine) was determined by single crystal X-ray diffraction. The bonding around each europium consists of two oxygen atoms of the chelated carboxyl group, two oxygen atoms of two water molecules and four oxygen atoms of the bidentate bridging carboxylate groups, forming an infinite polymeric chain structure. The luminescence behaviour of Eu 3+ in {[Eu( m-MOBA) 3·2H 2O]1/2(4,4'-bpy)} ∞ was observed at 77 K. The emission spectra of 5D 1→ 7F J ( J=1-3) and 5D 0→ 7F J ( J=0-4) transitions were recorded. The complex displays intense luminescence which may be related to the m-MOBA ligand and the polymeric coordination.

  15. Synthesis and luminescence properties of two novel europium (III) perchlorate complexes with bis(benzylsulfinyl)methane and 1,10-phenanthroline

    Energy Technology Data Exchange (ETDEWEB)

    Li, Wen-Xian, E-mail: nmglwx@163.com [College of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot 010021 (China); Guo, Feng [College of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot 010021 (China); Zheng, Yu-Shan [Inner Mongolia Autonomous Region Product Quality Inspection Institute, Hohhot 010010 (China); Cao, Xiao-Fang; Feng, Shu-Yan; Bai, Juan; Xin, Xiao-Dong [College of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot 010021 (China)

    2014-09-15

    Two novel binary and ternary Europium (III) perchlorate complexes were synthesized. The binary complex was prepared with bis(benzylsulfinyl)methane as ligand, and the ternary complex was with bis(benzylsulfinyl)methane as first ligand and 1,10-Phenanthroline as second ligand. They were characterized by element analysis, molar conductivity, coordination titration analysis, IR, TG-DSC, {sup 1}HNMR and UV spectra. The results indicated that the composition of binary and ternary complexes was EuL{sub 2.5}·(ClO{sub 4}){sub 3}·3H{sub 2}O and Eu{sub 2}L{sub 4}·phen·(ClO{sub 4}){sub 6}·12H{sub 2}O (L=C{sub 6}H{sub 5}CH{sub 2}SOCH{sub 2}SOCH{sub 2}C{sub 6}H{sub 5}), respectively. The fluorescent spectra illustrated that the complexes displayed characteristic Europium (III) ion fluorescence in solid state, indicating the ligands favored energy transfer to the excitation state energy level of it. The strongest characteristic fluorescence emission intensity of the ternary system was 1.87 times as strong as that of the binary system. The fluorescent quantum yields of the Eu (III) ternary and binary complexes were also calculated. Additionally, the phosphorescence spectra and the luminescence mechanisms of the complexes were studied and explained. - Highlights: • Two rare earth complexes are new. And they are stabilized. • The intensities of the two rare earth complexes were all stronger and the lifetimes were longer. • The introduction of the second organic ligand1,10-Phenanthroline enhanced the fluorescence intensity. • The fluorescent quantum yields of two complexes being calculated are both very high.

  16. Luminescent europium and terbium complexes of dipyridoquinoxaline and dipyridophenazine ligands as photosensitizing antennae: structures and biological perspectives.

    Science.gov (United States)

    Dasari, Srikanth; Patra, Ashis K

    2015-12-14

    The europium(III) and terbium(III) complexes, namely [Eu(dpq)(DMF)2(NO3)3] (1), [Eu(dppz)2(NO3)3] (2), [Tb(dpq)(DMF)2Cl3] (3), and [Tb(dppz)(DMF)2Cl3] (4), where dipyrido[3,2-d:2',3'-f]quinoxaline (dpq in 1 and 3), dipyrido[3,2-a:2',3'-c]phenazine (dppz in 2 and 4) and N,N'-dimethylformamide (DMF) have been isolated, characterized from their physicochemical data, luminescence studies and their interaction with DNA, serum albumin protein and photo-induced DNA cleavage activity are studied. The X-ray crystal structures of complexes 1-4 show discrete mononuclear Ln(3+)-based structures. The Eu(3+) in [Eu(dpq)(DMF)2(NO3)3] (1) and [Eu(dppz)2(NO3)3] (2) as [Eu(dppz)2(NO3)3]·dppz (2a) adopts a ten-coordinated bicapped dodecahedron structure with a bidentate N,N-donor dpq ligand, two DMF and three NO3(-) anions in 1 and two bidentate N,N-donor dppz ligands and three NO3(-) anions in 2. Complexes 3 and 4 show a seven-coordinated mono-capped octahedron structure where Tb(3+) contains bidentate dpq/dppz ligands, two DMF and three Cl(-) anions. The complexes are highly luminescent in nature indicating efficient photo-excited energy transfer from the dpq/dppz antenna to Ln(3+) to generate long-lived emissive excited states for characteristic f → f transitions. The time-resolved luminescence spectra of complexes 1-4 show typical narrow emission bands attributed to the (5)D0 → (7)F(J) and (5)D4 → (7)F(J) f-f transitions of Eu(3+) and Tb(3+) ions respectively. The number of inner-sphere water molecules (q) was determined from luminescence lifetime measurements in H2O and D2O confirming ligand-exchange reactions with water in solution. The complexes display significant binding propensity to the CT-DNA giving binding constant values in the range of 1.0 × 10(4)-6.1 × 10(4) M(-1) in the order 2, 4 (dppz) > 1, 3 (dpq). DNA binding data suggest DNA groove binding with the partial intercalation nature of the complexes. All the complexes also show binding propensity (K(BSA)

  17. Application of a room temperature ionic liquid for nuclear spent fuel reprocessing: speciation of trivalent europium and solvatation effects; Application d'un liquide ionique basse temperature pour les procedes de separation: speciation de l'europium trivalent et effets solvatation

    Energy Technology Data Exchange (ETDEWEB)

    Moutiers, G.; Mekki, S. [CEA Saclay, Dept. de Physico-Chimie, Service de Chimie Physique, 91 - Gif sur Yvette (France); Billard, I. [IN2P3/CNRS, 69 - Villeurbanne (France)

    2007-07-01

    One of the solutions proposed for the optimization of the long term storage and conditioning of spent nuclear fuel is to separate actinide and lanthanide both from each other and from other less radioactive metallic species. The industrial proposed processes, based on liquid liquid extraction steps, involve solvents with non negligible vapour pressure and may generate contaminated liquid wastes that will have to be reprocessed. During the last decade, some room-temperature ionic liquids have been studied and integrated into industrial processes. The interest on this class of solvent came out from their 'green' properties (non volatile, non flammable, recyclable, etc...), but also from the variability of their physico-chemical properties (stability, hydrophobicity, viscosity) as a function of the RTIL chemical composition. Indeed, it has been shown that classical chemical industrial processes could be transferred into those media, even more improved, while a certain number of difficulties arising from using traditional solvent can be avoided. In this respect, it could be promising to investigate the ability to use room temperature ionic liquid into the spent nuclear fuel reprocessing field. The aim of this this study is to test the ability of the specific ionic liquid bumimTf{sub 2}N to allow trivalent europium extraction. The choice of this metal is based on the chemical analogy with trivalent minor actinides Curium and Americium which are contributing the greatest part of the long-lived high level radioactive wastes. Handling these elements needs to be very cautious for the safety and radioprotection aspect. Moreover, europium is a very sensitive luminescent probe to its environment even at the microscopic scale. The report is structured with four parts. In a first chapter, we present the main physico-chemical properties of an imidazolium-based ionic liquid family, and then we choose the ionic liquid bumimTf{sub 2}N for the whole thesis and start with

  18. Synthesis, characterization and luminescence of europium perchlorate with MABA-Si complex and coating structure SiO2@Eu(MABA-Si) luminescence nanoparticles.

    Science.gov (United States)

    Fu, Zhi-Fang; Li, Wen-Xian; Bai, Juan; Bao, Jin-Rong; Cao, Xiao-Fang; Zheng, Yu-Shan

    2017-05-01

    This article reports a novel category of coating structure SiO 2 @Eu(MABA-Si) luminescence nanoparticles (NPs) consisting of a unique organic shell, composed of perchlorate europium(III) complex, and an inorganic core, composed of silica. The binary complex Eu(MABA-Si) 3 ·(ClO 4 ) 3 ·5H 2 O was synthesized using HOOCC 6 H 4 N(CONH(CH 2 ) 3 Si(OCH 2 CH 3 ) 3 ) 2 (MABA-Si) and was used as a ligand. Furthermore, the as-prepared silica NPs were successfully coated with the -Si(OCH 2 CH 3 ) 3 group of MABA-Si to form Si-O-Si chemical bonds by means of the hydrolyzation of MABA-Si. The binary complexes were characterized by elemental analysis, molar conductivity and coordination titration analysis. The results indicated that the composition of the binary complex was Eu(MABA-Si) 3 ·(ClO 4 ) 3 ·5H 2 O. Coating structure SiO 2 @Eu(MABA-Si) NPs were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM) and infrared (IR) spectra. Based on the SEM and TEM measurements, the diameter of core-SiO 2 particles was ~400 and 600 nm, and the thickness of the cladding layer Eu(MABA-Si) was ~20 nm. In the binary complex Eu(MABA-Si) 3 ·(ClO 4 ) 3 ·5H 2 O, the fluorescence spectra illustrated that the energy of the ligand MABA-Si transferred to the energy level for the excitation state of europium(III) ion. Coating structure SiO 2 @Eu(MABA-Si) NPs exhibited intense red luminescence compared with the binary complex. The fluorescence lifetime and fluorescence quantum efficiency of the binary complex and of the coating structure NPs were also calculated. The way in which the size of core-SiO 2 spheres influences the luminescence was also studied. Moreover, the luminescent mechanisms of the complex were studied and explained. Copyright © 2016 John Wiley & Sons, Ltd.

  19. The structures of CyMe4-BTBP complexes of americium(iii) and europium(iii) in solvents used in solvent extraction, explaining their separation properties.

    Science.gov (United States)

    Ekberg, Christian; Löfström-Engdahl, Elin; Aneheim, Emma; Foreman, Mark R StJ; Geist, Andreas; Lundberg, Daniel; Denecke, Melissa; Persson, Ingmar

    2015-11-14

    Separation of trivalent actinoid (An(iii)) and lanthanoid (Ln(iii)) ions is extremely challenging due to their similar ionic radii and chemical properties. Poly-aromatic nitrogen compounds acting as tetradentate chelating ligands to the metal ions in the extraction, have the ability to sufficiently separate An(iii) from Ln(iii). One of these compounds, 6,6'-bis(5,5,8,8-tetramethyl-5,6,7,8-tetrahydro-benzol[1,2,4]triazin-3-yl)[2,2]bipyridine, CyMe4-BTBP, has proven to be resistant towards acidic environments and strong radiation from radioactive decomposition. EXAFS studies of the dicomplexes of CyMe4-BTBP with americium(iii) and europium(iii) in nitrobenzene, cyclohexanone, 1-hexanol, 1-octanol and malonamide (DMDOHEMA) in 1-octanol have been carried out to get a deeper understanding of the parameters responsible for the separation. The predominating complexes independent of solvent used are [Am(CyMe4-BTBP)2(NO3)](2+) and [Eu(CyMe4-BTBP)2](3+), respectively, which are present as outer-sphere ion-pairs with nitrate ions in the studied solvents with low relative permittivity. The presence of a nitrate ion in the first coordination sphere of the americium(iii) complex compensates the charge density of the complex considerably in comparison when only outer-sphere ion-pairs are formed as for the [Eu(CyMe4-BTBP)2](3+) complex. The stability and solubility of a complex in a solvent with low relative permittivity increase with decreasing charge density. The [Am(CyMe4-BTBP)2(NO3)](2+) complex will therefore be increasingly soluble and stabilized over the [Eu(CyMe4-BTBP)2](3+) complex in solvents with decreasing relative permittivity of the solvent. The separation of americium(iii) from europium(iii) with CyMe4-BTBP as extraction agent will increase with decreasing relative permittivity of the solvent, and thereby also with decreasing solubility of CyMe4-BTBP. The choice of solvent is therefore a balance of a high separation factor and sufficient solubility of the CyMe4-BTBP

  20. Europium-decorated graphene quantum dots as a fluorescent probe for label-free, rapid and sensitive detection of Cu{sup 2+} and L-cysteine

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Liping [College of Life Sciences, Fujian Agriculture and Forestry University, Fuzhou, 350002 (China); Song, Xinhong; Chen, Yiying; Rong, Mingcong; Wang, Yiru [Department of Chemistry and the MOE Key Laboratory of Spectrochemical Analysis & Instrumentation, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen, 361005 (China); Zhao, Li; Zhao, Tingting [Xiamen Huaxia College, Xiamen, 361024 (China); Chen, Xi, E-mail: xichen@xmu.edu.cn [Department of Chemistry and the MOE Key Laboratory of Spectrochemical Analysis & Instrumentation, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen, 361005 (China); State Key Laboratory of Marine Environmental Science, Xiamen University, Xiamen, 361005 (China)

    2015-09-03

    In this work, europium-decorated graphene quantum dots (Eu-GQDs) were prepared by treating three-dimensional Eu-decorated graphene (3D Eu-graphene) via a strong acid treatment. Various characterizations revealed that Eu atoms were successfully complexed with the oxygen functional groups on the surface of graphene quantum dots (GQDs) with the atomic ratio of 2.54%. Compared with Eu free GQDs, the introduction of Eu atoms enhanced the electron density and improved the surface chemical activities of Eu-GQDs. Therefore, the obtained Eu-GQDs were used as a novel “off-on” fluorescent probe for the label-free determination of Cu{sup 2+} and L-cysteine (L-Cys) with high sensitivity and selectivity. The fluorescence intensity of Eu-GQDs was quenched in the presence of Cu{sup 2+} owing to the coordination reaction between Cu{sup 2+} and carboxyl groups on the surface of the Eu-GQDs. The fluorescence intensity of Eu-GQDs recovered with the subsequent addition of L-Cys because of the strong affinity of Cu{sup 2+} to L-Cys via the Cu–S bond. The experimental results showed that the fluorescence variation of the proposed approach had a good linear relationship in the range of 0.1–10 μM for Cu{sup 2+} and 0.5–50 μM for L-Cys with corresponding detection limits of 0.056 μM for Cu{sup 2+} and 0.31 μM for L-Cys. The current approach also displayed a special response to Cu{sup 2+} and L-Cys over the other co-existing metal ions and amino acids, and the results obtained from buffer-diluted serum samples suggested its applicability in biological samples. - Highlights: • The europium-decorated graphene quantum dots (Eu-GQDs) have been successfully prepared. • Various characterizations results proved that Eu atoms were successfully introduced into graphene quantum dots. • The introduced Eu atoms changed the electron density and surface chemical activities of Eu-GQDs. • Eu-GQDs were used as an “off-on” fluorescent probe for Cu{sup 2+} and L-cysteine detection

  1. Synthesis, structural characterization and luminescent properties of a novel europium ternary complex Eu(2-A-4-CBA){sub 3}phen

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Yongjie, E-mail: cyj200507@aliyun.com; Wu, Shengnan; Xing, Zhenfang; Cao, Shuang; Geng, Xiujuan; Yang, Ying; Xiao, Linjiu

    2015-11-15

    The preparation of a novel europium ternary complex with the formula of Eu(2-A-4-CBA){sub 3}phen (where, 2-A-4-CBA = 2-amino-4-chlorobenzoic acid, phen = 1,10-phenanthroline) under solvothermal condition is described. The composition and structure of the resulting complex were investigated by elemental analysis, Fourier transform infrared (FT-IR) spectroscopy. The complex is polycrystalline, and the morphology is clean and regular as revealed by scanning electron microscope (SEM). The luminescent and thermal properties of the complex were researched by fluorescence spectroscopy and thermogravimetric analysis, respectively. Of importance here is that, the room-temperature luminescence spectra of the complex show strong characteristic emission of the corresponding Eu{sup 3+}, which is attributed to the energy transfer from ligands to Eu{sup 3+} via an Antenna effect. It is also found that the complex exhibits pure red light and high color purity. In addition, the complex does not decompose until 300 °C, so it exhibits good thermal stability. - Highlights: • A novel Eu(III) complex was synthesized by solvothermal synthesis method. • The structure and properties of complex were studied. • The complex can emits pure red light and has a high color purity. • The complex does not decompose until 300 °C and it has a good thermal stability.

  2. Size- and dimensionality-dependent optical, magnetic and magneto-optical properties of binary europium-based nanocrystals: EuX (X = O, S, Se, Te).

    Science.gov (United States)

    Zhou, Xingzhi; Zhang, Kelvin H L; Xiong, Jie; Park, Ju-Hyun; Dickerson, James H; He, Weidong

    2016-05-13

    Europium chalcogenides (EuX, X = O, S, Se, Te), a class of prototypical Heisenberg magnetic semiconductors, exhibit intriguing properties in optics, magnetism, and magneto-optics at the nanoscale, and have broad application potential in optical/magnetic sensors, spintronics, optical isolators, etc. EuX nanocrystals (NCs) exhibit enhanced properties, such as high saturation magnetization, a strong magneto-optic effect (Faraday rotation), and high magneto resistance, which are all unanimously dependent on the NC's size, shape, and surface information. In this report, we give an overview of the fundamental properties of bulk EuX, and illustrate the quantum confinement effects on the optical, magnetic and magneto-optical properties of EuX nanostructures. We then focus on doping and self-assembly-two efficient methods that enhance magnetic properties by manipulating magnetic coupling in EuX nanostructures. In particular, we look towards future research on Eu(2+) NCs, which along with the overview provides an up-to-date platform for evaluating the fundamental properties and application potential of Eu-based semiconductors.

  3. Crystal structure and luminescence properties of the first hydride oxide chloride with divalent europium. LiEu{sub 2}HOCl{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Rudolph, Daniel; Schleid, Thomas [Institute for Inorganic Chemistry, University of Stuttgart (Germany); Enseling, David; Juestel, Thomas [Department of Chemical Engineering, Muenster University of Applied Sciences, Steinfurt (Germany)

    2017-11-17

    The mixed-anionic hydride oxide chloride LiEu{sub 2}HOCl{sub 2} with divalent europium was synthesized by the reduction of Eu{sub 2}O{sub 3} with LiH in a LiCl flux at 750 C for 4 d in silica-jacketed niobium capsules. According to structure determination by single-crystal X-ray diffraction the yellow compound crystallizes in the orthorhombic space group Cmcm (a = 1492.30(11) pm, b = 570.12(4) pm, c = 1143.71(8) pm, Z = 8) with a crystal structure closely related to that one of the quaternary hydride oxide LiLa{sub 2}HO{sub 3} and the hydride nitride LiSr{sub 2}H{sub 2}N. On the other hand it can also be derived from the PbFCl-type structure of EuHCl showing astonishingly short Eu{sup 2+}..Eu{sup 2+} contacts of 326 and 329 pm. Both crystallographically different Eu{sup 2+} cations have nine anionic neighbors, while all other ions (Li{sup +}, H{sup -}, O{sup 2-} and Cl{sup -}) reside in six-membered coordination spheres. LiEu{sub 2}OCl{sub 2}H exhibits a bright yellow luminescence with an emission maximum at 581 nm upon excitation at 440 nm. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. Highly sensitive and novel point-of-care system, aQcare Chlamydia TRF kit for detecting Chlamydia trachomatis by using europium (Eu) (III) chelated nanoparticles.

    Science.gov (United States)

    Ham, Ji Yeon; Jung, Jaean; Hwang, Byung-Gap; Kim, Won-Jung; Kim, Young-Seop; Kim, Eun-Ju; Cho, Mi-Yeon; Hwang, Mi-Sun; Won, Dong Il; Suh, Jang Soo

    2015-01-01

    The bacterium Chlamydia trachomatis is one of the leading causes of sexually transmitted diseases worldwide. Since no simple and effective tool exists to diagnose C. trachomatis infections, we evaluated a novel point-of-care (POC) test, aQcare Chlamydia TRF kit, which uses europium-chelated nanoparticles and a time-resolved fluorescence reader. The test performance was evaluated by comparing the results obtained using the novel POC testing kit with those obtained using a nucleic acid amplification test (NAAT), using 114 NAAT-positive and 327 NAAT-negative samples. The cut-off value of the novel test was 20.8 with a detection limit of 0.27 ng/mL. No interference or cross-reactivity was observed. Diagnostic accuracy showed an overall sensitivity of 93.0% (106/114), specificity of 96.3% (315/327), positive predictive value (PPV) of 89.8% (106/118), and negative predictive value (NPV) of 97.5% (315/323). The sensitivity of the novel test was much higher than that of currently available POC tests. Furthermore, the relative ease and short turnaround time (30 min) of this assay enables C. trachomatis-infected individuals to be treated without a diagnostic delay. This simple and novel test is a potential tool to screen a larger population, especially those in areas with limited resources.

  5. Fluorescence enhancement of europium (III) perchlorate by 1,10-phenanthroline on the 1-(naphthalen-2-yl)-2-(phenylsulthio)ethanone complex and luminescence mechanism.

    Science.gov (United States)

    Li, Wen-Xian; Xin, Xiao-Dong; Feng, Shu-Yan; Liu, Yu; Zhang, Jing; Ao, Bo-Yang; Li, Ying-Jie

    2014-11-01

    A novel ligand, 1-(naphthalen-2-yl)-2-(phenylsulthio)ethanone was synthesized using a new method and its two europium (Eu) (III) complexes were synthesized. The compounds were characterized by elemental analysis, coordination titration analysis, molar conductivity, infrared, thermo gravimetric analyzer-differential scanning calorimetry (TGA-DSC), (1)H NMR and UV spectra. The composition was suggested as EuL5 · (ClO4)3 · 2H2O and EuL4 · phen(ClO4)3 · 2H2O (L = C(10)H(7)COCH(2)SOC(6)H(5)). The fluorescence spectra showed that the Eu(III) displayed strong characteristic metal-centered fluorescence in the solid state. The ternary rare earth complex showed stronger fluorescence intensity than the binary rare earth complex in such material. The strongest characteristic fluorescence emission intensity of the ternary system was 1.49 times as strong as that of the binary system. The phosphorescence spectra were also discussed. Copyright © 2014 John Wiley & Sons, Ltd.

  6. Matrix-Assisted Ionization-Ion Mobility Spectrometry-Mass Spectrometry: Selective Analysis of a Europium-PEG Complex in a Crude Mixture.

    Science.gov (United States)

    Fischer, Joshua L; Lutomski, Corinne A; El-Baba, Tarick J; Siriwardena-Mahanama, Buddhima N; Weidner, Steffen M; Falkenhagen, Jana; Allen, Matthew J; Trimpin, Sarah

    2015-12-01

    The analytical utility of a new and simple to use ionization method, matrix-assisted ionization (MAI), coupled with ion mobility spectrometry (IMS) and mass spectrometry (MS) is used to characterize a 2-armed europium(III)-containing poly(ethylene glycol) (Eu-PEG) complex directly from a crude sample. MAI was used with the matrix 1,2-dicyanobenzene, which affords low chemical background relative to matrix-assisted laser desorption/ionization (MALDI) and electrospray ionization (ESI). MAI provides high ion abundance of desired products in comparison to ESI and MALDI. Inductively coupled plasma-MS measurements were used to estimate a maximum of 10% of the crude sample by mass was the 2-arm Eu-PEG complex, supporting evidence of selective ionization of Eu-PEG complexes using the new MAI matrix, 1,2-dicyanobenzene. Multiply charged ions formed in MAI enhance the IMS gas-phase separation, especially relative to the singly charged ions observed with MALDI. Individual components are cleanly separated and readily identified, allowing characterization of the 2-arm Eu-PEG conjugate from a mixture of the 1-arm Eu-PEG complex and unreacted starting materials. Size-exclusion chromatography, liquid chromatography at critical conditions, MALDI-MS, ESI-MS, and ESI-IMS-MS had difficulties with this analysis, or failed. Graphical Abstract ᅟ.

  7. Synthesis, characterization and luminescent properties of europium complexes with 2,4,6-tris-(2-pyridyl)-s-triazine as highly efficient sensitizers.

    Science.gov (United States)

    Kang, Jie; Chen, Ying-Nan; Wang, Ai-Ling; Li, Hai-Yan; Qu, Yan-Rong; Zhang, Hai-Xia; Chu, Hai-Bin; Zhao, Yong-Liang

    2015-12-01

    Using 2,4,6-tris-(2-pyridyl)-s-triazine (TPTZ) as a neutral ligand, and p-hydroxybenzoic acid, terephthalic acid and nitrate as anion ligands, five novel europium complexes have been synthesized. These complexes were characterized using elemental analysis, rare earth coordination titrations, UV/vis absorption spectroscopy and infrared spectroscopy. Luminescence spectra, luminescence lifetime and quantum efficiency were investigated and the mechanism discussed in depth. The results show that the complexes have excellent emission intensities, long emission lifetimes and high quantum efficiencies. The superior luminescent properties of the complexes may be because the triplet energy level of the ligands matches well with the lowest excitation state energy level of Eu(3+). Moreover, changing the ratio of the ligands and metal ions leads to different luminescent properties. Among the complexes, Eu2(TPTZ)2(C8H4O4)(NO3)4(C2H5OH)·H2O shows the strongest luminescence intensity, longest emission lifetime and highest quantum efficiency. Copyright © 2015 John Wiley & Sons, Ltd.

  8. Photo-catalytic inactivation of an Enterococcus biofilm: the anti-microbial effect of sulphated and europium-doped titanium dioxide nanopowders.

    Science.gov (United States)

    Dworniczek, Ewa; Plesch, Gustav; Seniuk, Alicja; Adamski, Ryszard; Michal, Róbert; Čaplovičová, Mária

    2016-04-01

    The control and prevention of biofilm-related infections is an important public healthcare issue. Given the increasing antibiotic resistance among bacteria and fungi that cause serious infections in humans, promotion of new strategies combating microorganisms has been essential. One attractive approach to inactivate microorganisms is the use of semiconductor photo-catalysis, which has become the subject of extensive research. In this study, the bactericidal properties of four photo-catalysts, TiO₂, TiO₂-S, TiO₂-Eu and TiO₂-Eu-S, were investigated against established 24, 48, 72 and 96 h biofilms of Enterococcus The exposure of biofilms to the catalysts induced the production of superoxide radical anions. The best photo-catalytic inactivation was achieved with the TiO₂-Eu-S and TiO₂-S nanopowders and 24 h biofilms. Transmission electron microscopy images showed significant changes in the structure of the biofilm cells following photo-inactivation. The results suggest that doping with europium and modifying the surface with sulphate groups enhanced the bactericidal activity of the TiO₂ nanoparticles against enterococcal biofilms. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  9. Reversible modulation in luminescence intensity of a single vesicle composed of diblock azo-copolymer and tris(dibenzoylmethanate)(phenanthroline)europium(III)

    Science.gov (United States)

    Yan, Qing; Su, Wei; Chen, Yilong; Luo, Yanhua; Zhang, Qijin

    2009-01-01

    Tris(dibenzoylmethanate)(phenanthroline)europium(III)[Eu(DBM) 3Phen]-doped amphiphilic vesicles were obtained by self-assembling of poly( N-isopropylacrylamide)- b-poly{6-[4-(4-methylphenyl-azo) phenoxy] hexylacrylate} (PNIPAM 83- b-PAzoM 20) in presence of Eu(DBM) 3Phen in the mixed solvent of THF/H 2O (50/50 vol.%). Their optical properties were studied by UV-vis and fluorescence spectroscopies. The UV-vis spectrum showed that the electronic transition bands of azobenzene and Eu(DBM) 3Phen were overlapped at about 365 nm and the main peak of fluorescence emission band appeared at 612 nm. So the vesicles showed obvious red luminescence. It was found that the fluorescence intensity of a single Eu(DBM) 3Phen-doped vesicle could be modulated by irradiation with UV and visible light due to the reversible trans- cis- trans photoisomerization reaction of azobenzene moiety. Possible energy allocation process for this property was discussed in details.

  10. Size- and dimensionality-dependent optical, magnetic and magneto-optical properties of binary europium-based nanocrystals: EuX (X = O, S, Se, Te)

    Science.gov (United States)

    Zhou, Xingzhi; Zhang, Kelvin HL; Xiong, Jie; Park, Ju-Hyun; Dickerson, James H.; He, Weidong

    2016-05-01

    Europium chalcogenides (EuX, X = O, S, Se, Te), a class of prototypical Heisenberg magnetic semiconductors, exhibit intriguing properties in optics, magnetism, and magneto-optics at the nanoscale, and have broad application potential in optical/magnetic sensors, spintronics, optical isolators, etc. EuX nanocrystals (NCs) exhibit enhanced properties, such as high saturation magnetization, a strong magneto-optic effect (Faraday rotation), and high magneto resistance, which are all unanimously dependent on the NC’s size, shape, and surface information. In this report, we give an overview of the fundamental properties of bulk EuX, and illustrate the quantum confinement effects on the optical, magnetic and magneto-optical properties of EuX nanostructures. We then focus on doping and self-assembly—two efficient methods that enhance magnetic properties by manipulating magnetic coupling in EuX nanostructures. In particular, we look towards future research on Eu2+ NCs, which along with the overview provides an up-to-date platform for evaluating the fundamental properties and application potential of Eu-based semiconductors.

  11. A novel near monochromatic red emissive europium(III) metal-organic framework based on 1,2,4,5-benzenetetracarboxylate: From synthesis to photoluminescence studies

    Science.gov (United States)

    Lahoud, Marcelo G.; Frem, Regina C. G.; Marques, Lippy F.; Arroyos, Guilherme; Brandão, Paula; Ferreira, Rute A. S.; Carlos, Luís D.

    2017-09-01

    This work presents the synthesis, solid state characterization (infrared spectroscopy, thermal analysis (TGA/DTA), powder and single crystal X-ray diffraction) and photoluminescence studies of a new europium metal-organic framework (MOF), [Eu2(Btec)1,5(H2O)]n (Btec4-=1,2,4,5-benzenetetracarboxylate anion). Single crystal X-ray diffraction analysis reveals that the material has a three-dimensional network, with two crystallographically independent Eu(III) ions adopting different coordination geometries. This structure presents one of the Btec4- anions acting as a μ8-bridging linker, with the carboxylate groups in distinct connection to Eu(III) ions, culminating into an unknown coordination mode for the linker. The results of thermogravimetric analyses indicate that the MOF has high thermal stability, with this characteristic being of great interest for the application of these compounds in several fields such as catalysis and photonics. The luminescent properties showed that the Eu(III) ions are a local-spectroscopic probe, with the compound presenting a red emission when excited in the UV spectral region with absolute emission quantum yield values of 0.48 ± 0.05. The thermal dependence on the intensity of the transitions originating from the 7F1 level, especially the 7F1 → 5D1 transition, was studied. These results opens the possibility to test this MOF [Eu2(Btec)1.5(H2O)]n in the field of molecular thermometry.

  12. Study of sorption mechanisms of europium(3) and uranium(6) ions on clays : impact of silicates; Etude des mecanismes de retention des ions U(6) et Eu(3) sur les argiles: influence des silicates

    Energy Technology Data Exchange (ETDEWEB)

    Kowal-Fouchard, A

    2002-11-01

    Bentonite clay has been selected as a potential buffer or backfill material in a number of disposal programmes for high level waste. In order to enhance the thermodynamic database of sorption phenomena at the solid-water interface, we have investigated sorption mechanisms of europium(III) and uranium(VI) ions onto montmorillonite and bentonite. Thermodynamic data were obtained for different ions concentrations, different background electrolytes and different ionic strengths. The structural identification of the surface complexes and sorption sites was carried out using two spectroscopies, XPS and TRLIFS, while sorption edges were performed using batch experiments. However, clays are complex minerals and in order to understand these sorption mechanisms we have studied europium(III) and uranium(VI) retention on a silica and an alumina because these solids are often considered as basic components of clays. The comparison of structural results shows that europium ions are significantly sorbed on permanently charged sites of clay until pH 7. But this ion is also sorbed on {identical_to}SiOH and {identical_to}AlOH sites of montmorillonite at pH higher than 6. Uranyl ions sorption on montmorillonite is mainly explained by retention of three complexes on {identical_to}SiOH sites. Moreover, we have shown that nitrate ions and dissolved silicates affect on uranium(VI) sorption mechanisms onto alumina. Nevertheless, uranyl ions sorption on montmorillonite and bentonite only decreases with increasing carbonate concentration. Finally, all the sorption edges were then modeled using these results and a surface complexation model (2 pK and constant capacitance models). (author)

  13. Distribution of micro-amounts of europium in the two-phase water–HCl–nitrobenzene–N,N’-dimethyl-N,N’-diphenyl-2,6-di-picolinamide–hydrogen dicarbollylcobaltate extraction system

    Directory of Open Access Journals (Sweden)

    EMANUEL MAKRLÍK

    2009-07-01

    Full Text Available Extraction of micro-amounts of europium by a nitrobenzene solution of hydrogen dicarbollylcobaltate (H+B- in the presence of N,N’-dimethyl-N,N’-diphenyl-2,6-dipicolinamide (MePhDPA, L was investigated. The equilibrium data were explained assuming that the species HL+, HL+2, HL3+2 and HL3+3 are extracted into the organic phase. The values of the extraction and stability constants of the species in nitrobenzene saturated with water were determined.

  14. Europium-doped Gd2O3 nanotubes cause the necrosis of primary mouse bone marrow stromal cells through lysosome and mitochondrion damage.

    Science.gov (United States)

    Jin, Yi; Chen, Shizhu; Duan, Jianlei; Jia, Guang; Zhang, Jinchao

    2015-05-01

    With the wide applications of europium-doped Gd2O3 nanoparticles (Gd2O3:Eu(3+) NPs) in biomedical fields, it will inevitably increase the chance of human exposure. It was reported that Gd2O3:Eu(3+) NPs could accumulate in bone. However, there have been few reports about the potential effect of Gd2O3:Eu(3+) NPs on bone marrow stromal cells (BMSCs). In this study, the Gd2O3:Eu(3+) nanotubes were prepared and characterized by powder X-ray diffraction (XRD), photoluminescence (PL) excitation and emission spectra, scanning electron microscope (SEM), and transmission electron microscopy (TEM). The cytotoxicity of Gd2O3:Eu(3+) nanotubes on BMSCs and the associated mechanisms were further studied. The results indicated that they could be uptaken into BMSCs by an energy-dependent and macropinocytosis-mediated endocytosis process, and primarily localized in lysosome. Gd2O3:Eu(3+) nanotubes effectively inhibited the viability of BMSCs in concentration and time-dependent manners. A significant increase in the percentage of late apoptotic/necrotic cells, lactate dehydrogenase (LDH) leakage and the number of PI-stained cells was found after BMSCs were treated by 10, 20, and 40μg/mL of Gd2O3:Eu(3+) nanotubes for 12h. No obvious DNA ladders were detected, but a dispersed band was observed. The above results revealed that Gd2O3:Eu(3+) nanotubes could trigger cell death by necrosis instead of apoptosis. Two mechanisms were involved in Gd2O3:Eu(3+) nanotube-induced BMSCs necrosis: lysosomal rupture and release of cathepsins B; and the overproduction of reactive oxygen species (ROS) injury to the mitochondria and DNA. The study provides novel evidence to elucidate the toxicity mechanisms and may be beneficial to more rational applications of these nanomaterials in the future. Copyright © 2015 Elsevier Inc. All rights reserved.

  15. Europium-decorated graphene quantum dots as a fluorescent probe for label-free, rapid and sensitive detection of Cu(2+) and L-cysteine.

    Science.gov (United States)

    Lin, Liping; Song, Xinhong; Chen, Yiying; Rong, Mingcong; Wang, Yiru; Zhao, Li; Zhao, Tingting; Chen, Xi

    2015-09-03

    In this work, europium-decorated graphene quantum dots (Eu-GQDs) were prepared by treating three-dimensional Eu-decorated graphene (3D Eu-graphene) via a strong acid treatment. Various characterizations revealed that Eu atoms were successfully complexed with the oxygen functional groups on the surface of graphene quantum dots (GQDs) with the atomic ratio of 2.54%. Compared with Eu free GQDs, the introduction of Eu atoms enhanced the electron density and improved the surface chemical activities of Eu-GQDs. Therefore, the obtained Eu-GQDs were used as a novel "off-on" fluorescent probe for the label-free determination of Cu(2+) and l-cysteine (L-Cys) with high sensitivity and selectivity. The fluorescence intensity of Eu-GQDs was quenched in the presence of Cu(2+) owing to the coordination reaction between Cu(2+) and carboxyl groups on the surface of the Eu-GQDs. The fluorescence intensity of Eu-GQDs recovered with the subsequent addition of L-Cys because of the strong affinity of Cu(2+) to L-Cys via the Cu-S bond. The experimental results showed that the fluorescence variation of the proposed approach had a good linear relationship in the range of 0.1-10 μM for Cu(2+) and 0.5-50 μM for L-Cys with corresponding detection limits of 0.056 μM for Cu(2+) and 0.31 μM for L-Cys. The current approach also displayed a special response to Cu(2+) and L-Cys over the other co-existing metal ions and amino acids, and the results obtained from buffer-diluted serum samples suggested its applicability in biological samples. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Sensitive detection of influenza viruses with Europium nanoparticles on an epoxy silica sol-gel functionalized polycarbonate-polydimethylsiloxane hybrid microchip.

    Science.gov (United States)

    Liu, Jikun; Zhao, Jiangqin; Petrochenko, Peter; Zheng, Jiwen; Hewlett, Indira

    2016-12-15

    In an effort to develop new tools for diagnosing influenza in resource-limited settings, we fabricated a polycarbonate (PC)-polydimethylsiloxane (PDMS) hybrid microchip using a simple epoxy silica sol-gel coating/bonding method and employed it in sensitive detection of influenza virus with Europium nanoparticles (EuNPs). The incorporation of sol-gel material in device fabrication provided functionalized channel surfaces ready for covalent immobilization of primary antibodies and a strong bonding between PDMS substrates and PC supports without increasing background fluorescence. In microchip EuNP immunoassay (µENIA) of inactivated influenza viruses, replacing native PDMS microchips with hybrid microchips allowed the achievement of a 6-fold increase in signal-to-background ratio, a 12-fold and a 6-fold decreases in limit-of-detection (LOD) in influenza A and B tests respectively. Using influenza A samples with known titers, the LOD of influenza µENIA on hybrid microchips was determined to be ~10(4) TCID50 titer/mL and 10(3)-10(4) EID50 titer/mL. A comparison test indicated that the sensitivity of influenza µENIA enhanced using the hybrid microchips even surpassed that of a commercial laboratory influenza ELISA test. In addition to the sensitivity improvement, assay variation was clearly reduced when hybrid microchips instead of native PDMS microchips were used in the µENIA tests. Finally, infectious reference viruses and nasopharyngeal swab patient specimens were successfully tested using μENIA on hybrid microchip platforms, demonstrating the potential of this unique microchip nanoparticle assay in clinical diagnosis of influenza. Meanwhile, the tests showed the necessity of using nucleic acid confirmatory tests to clarify ambiguous test results obtained from prototype or developed point-of-care testing devices for influenza diagnosis. Published by Elsevier B.V.

  17. A visible-light-excited europium(III) complex-based luminescent probe for visualizing copper ions and hydrogen sulfide in living cells

    Science.gov (United States)

    Wang, Yiren; Wang, Huan; Yang, Mei; Yuan, Jingli; Wu, Jing

    2018-01-01

    Development of visible-light-excited lanthanide (III) complex-based luminescent probes is highly appealing due to their superiority of less damage to the living biosystems over the conventional UV-light-excited ones. In this work, a visible-light-excited europium (III) complex-based luminescent probe, BPED-BHHCT-Eu3+-BPT, has been designed and synthesized by conjugating the Cu2+-binding N,N-bis(2-pyridylmethyl)ethanediamine (BPED) to a tetradentate β-diketone ligand 4,4‧-bis(1″,1″,1″,2″,2″,3″,3″-heptafluoro-4″,6″-hexanedione-6″-yl)chlorosulfo-o-terphenyl (BHHCT) and coordinating with a coligand 2-(N,N-diethylanilin-4-yl)-4,6-bis(pyrazol-1-yl)-1,3,5-triazine) (BPT) for the time-gated luminescence detection of Cu2+ ions and hydrogen sulfide (H2S) in living cells. BPED-BHHCT-Eu3+-BPT exhibited a sharp excitation peak at 407 nm and a wide excitation window extending to beyond 460 nm. Upon its reaction with Cu2+ ions, the luminescence of BPED-BHHCT-Eu3+-BPT was efficiently quenched, which could be reversibly restored by the addition of H2S due to the strong affinity between Cu2+ ions and H2S. The "on-off-on" type luminescence behavior of BPED-BHHCT-Eu3+-BPT towards Cu2+ ions and H2S enabled the sensing of the two species with high sensitivity and selectivity. The performances of BPED-BHHCT-Eu3+-BPT for visualizing intracellular Cu2+ ions and H2S were investigated, and the results have demonstrated the practical applicability of the probe for molecular imaging of cells.

  18. Chemical species of europium (III) in ionic force media 0.02M, 0.1M, and 0.7M NaClO{sub 4} at 298 K; Especies quimicas del europio (III) en medios de fuerza ionica 0.02M, 0.1M y 0.7M NaClO{sub 4} a 298 K

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez R, E.; Jimenez R, M.; Solache R, M. [Instituto Nacional de Investigaciones Nucleares, Departamento de Quimica, A.P. 18-1027, C.P. 11801 Mexico D.F. (Mexico)

    2000-07-01

    In order to know the effects of the controlled or accidental liberation of the europium in the environment, it is necessary to know its chemical behavior in found conditions in oceans, ground and surface water. The behavior of this element in these environments can be controlled mainly by the hydrolysis and its interaction with inorganic and organic ions. (Author)

  19. Computer Modeling of Ceramic Boride Composites

    Science.gov (United States)

    2014-11-01

    coefficients of thermal expansion. Approximately linear expansion coefficient of the composite is determined by the relation [52] EEE BBBAAAk...1 δαδαα ⋅+⋅= , (58) where AE and BE are Young moduli of components, and E – average modulus for composition BBAA EEE δδ

  20. Magnesium Aluminum Borides as Explosive Materials

    Science.gov (United States)

    2011-12-20

    Dryer , H. Rabitz, R. C. Brown, and C. E. Kolb, “Effect of Fluorine on the Combustion of “Clean” Surface Boron Particles,” Combustion and Flame, 112 507...521 (1998). 71. W. Zhou, R. A. Yetter, F. L. Dryer , H. Rabitz, R. C. Brown, and C. E. Kolb, “A Comprehensive Physical and Numerical Model of Boron...251-257 (1970). 114. T. Abu-Hamed, J. Karni, and M. Epstein, “The Use of Boron for Thermochemical Storage and Distribution of Solar Energy,” Solar

  1. Synthesis, single-crystal structure determination, and vibrational spectroscopy of the europium borate Eu[B{sub 6}O{sub 8}(OH){sub 5}].H{sub 3}BO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Ortner, Teresa S.; Wurst, Klaus; Huppertz, Hubert [Institut fuer Allgemeine, Anorganische und Theoretische Chemie, Leopold-Franzens-Universitaet Innsbruck (Austria); Seibald, Markus [OSRAM GmbH, Corporate Innovation, Schwabmuenchen (Germany); Joachim, Bastian [Institut fuer Mineralogie und Petrographie, Leopold-Franzens-Universitaet Innsbruck (Austria)

    2016-07-15

    The new europium borate Eu[B{sub 6}O{sub 8}(OH){sub 5}].H{sub 3}BO{sub 3} was obtained by hydrothermal synthesis from europium nitrate hydrate and boric acid. The compound crystallizes in the triclinic space group P1 (no. 2) with the lattice parameters a = 681.59(3), b = 714.17(3), c = 1271.88(6) pm, α = 96.02(1), β = 98.60(1), γ = 101.73(1) (Z = 2). The structure of Eu[B{sub 6}O{sub 8}(OH){sub 5}].H{sub 3}BO{sub 3} is isotypic to that of the samarium borate Sm[B{sub 6}O{sub 8}(OH){sub 5}].H{sub 3}BO{sub 3} and is built up from tetrahedral BO{sub 4} and trigonal-planar BO{sub 3} units, both of which are protonated at terminal and bridging oxygen positions. Boric acid molecules reside between the borate layers. Through hydrogen bonding, the structure forms a three-dimensional network. In channels down [110], the Eu{sup 3+} cations are eightfold coordinated by oxygen ions. The compound was also characterized by IR and Raman spectroscopy, and it shows typical Eu{sup 3+} line emission. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  2. Rapid and sensitive lateral flow immunoassay method for determining alpha fetoprotein in serum using europium (III) chelate microparticles-based lateral flow test strips

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Rong-Liang; Xu, Xu-Ping; Liu, Tian-Cai; Zhou, Jian-Wei; Wang, Xian-Guo; Ren, Zhi-Qi [Institute of Antibody Engineering, School of Biotechnology, Southern Medical University, Guangzhou 510515, Guangdong (China); Hao, Fen [DaAn Gene Co. Ltd. of Sun Yat-sen University, 19 Xiangshan Road, Guangzhou 510515 (China); Wu, Ying-Song, E-mail: wg@smu.edu.cn [Institute of Antibody Engineering, School of Biotechnology, Southern Medical University, Guangzhou 510515, Guangdong (China)

    2015-09-03

    Alpha-fetoprotein (AFP), a primary marker for many diseases including various cancers, is important in clinical tumor diagnosis and antenatal screening. Most immunoassays provide high sensitivity and accuracy for determining AFP, but they are expensive, often complex, time-consuming procedures. A simple and rapid point-of-care system that integrates Eu (III) chelate microparticles with lateral flow immunoassay (LFIA) has been developed to determine AFP in serum with an assay time of 15 min. The approach is based on a sandwich immunoassay performed on lateral flow test strips. A fluorescence strip reader was used to measure the fluorescence peak heights of the test line (H{sub T}) and the control line (H{sub C}); the H{sub T}/H{sub C} ratio was used for quantitation. The Eu (III) chelate microparticles-based LFIA assay exhibited a wide linear range (1.0–1000 IU mL{sup −1}) for AFP with a low limit of detection (0.1 IU mL{sup −1}) based on 5ul of serum. Satisfactory specificity and accuracy were demonstrated and the intra- and inter-assay coefficients of variation (CV) for AFP were both <10%. Furthermore, in the analysis of human serum samples, excellent correlation (n = 284, r = 0.9860, p < 0.0001) was obtained between the proposed method and a commercially available CLIA kit. Results indicated that the Eu (III) chelate microparticles-based LFIA system provided a rapid, sensitive and reliable method for determining AFP in serum, indicating that it would be suitable for development in point-of-care testing. - Highlights: • Europium (III) chelate microparticles was used as a label for LIFA. • Quantitative detection by using H{sub T}/H{sub C} ratio was achieved. • LIFA for simple and rapid AFP detection in human serum. • The sensitivity and linearity was more excellent compared with QD-based ICTS. • This method could be developed for rapid point-of-care screening.

  3. Crystal structure of monoclinic samarium and cubic europium sesquioxides and bound coherent neutron scattering lengths of the isotopes {sup 154}Sm and {sup 153}Eu

    Energy Technology Data Exchange (ETDEWEB)

    Kohlmann, Holger [Leipzig Univ. (Germany). Inst. of Inorganic Chemistry; Hein, Christina; Kautenburger, Ralf [Saarland Univ., Saarbruecken (Germany). Inorganic Solid State Chemistry; Hansen, Thomas C.; Ritter, Clemens [Institut Laue-Langevin, Grenoble (France); Doyle, Stephen [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany). Inst. for Synchrotron Radiation (ISS)

    2016-11-01

    The crystal structures of monoclinic samarium and cubic europium sesquioxide, Sm{sub 2}O{sub 3} and Eu{sub 2}O{sub 3}, were reinvestigated by powder diffraction methods (laboratory X-ray, synchrotron, neutron). Rietveld analysis yields more precise structural parameters than previously known, especially for oxygen atoms. Interatomic distances d(Sm-O) in Sm{sub 2}O{sub 3} range from 226.3(4) to 275.9(2) pm [average 241.6(3) pm] for the monoclinic B type Sm{sub 2}O{sub 3} [space group C2/m, a = 1418.04(3) pm, b = 362.660(7) pm, c = 885.48(2) pm, β = 100.028(1) ], d(Eu-O) in Eu{sub 2}O{sub 3} from 229.9(2) to 238.8(2) pm for the cubic bixbyite (C) type [space group Ia anti 3, a = 1086.87(1) pm]. Neutron diffraction at 50 K and 2 K did not show any sign for magnetic ordering in Sm{sub 2}O{sub 3}. Isotopically enriched {sup 154}Sm{sub 2}O{sub 3} and {sup 153}Eu{sub 2}O{sub 3} were used for the neutron diffraction work because of the enormous absorption cross section of the natural isotopic mixtures for thermal neutrons. The isotopic purity was determined by inductively coupled plasma - mass spectrometry to be 98.9% for {sup 154}Sm and 99.8% for {sup 153}Eu. Advanced analysis of the neutron diffraction data suggest that the bound coherent scattering lengths of {sup 154}Sm and {sup 153}Eu need to be revised. We tentatively propose b{sub c}({sup 154}Sm) = 8.97(6) fm and b{sub c}({sup 153}Eu) = 8.85(3) fm for a neutron wavelength of 186.6 pm to be better values for these isotopes, showing up to 8% deviation from accepted literature values. It is shown that inaccurate scattering lengths may result in severe problems in crystal structure refinements causing erroneous structural details such as occupation parameters, which might be critically linked to physical properties like superconductivity in multinary oxides.

  4. The adsorption of europium to colloidal iron oxyhydroxides and quartz - the impact of pH and an aquatic fulvic acid

    Energy Technology Data Exchange (ETDEWEB)

    Ledin, A. [Dept. of Water and Environmental Studies, Linkoeping Univ. (Sweden); Karlsson, S. [Dept. of Water and Environmental Studies, Linkoeping Univ. (Sweden); Dueker, A. [Dept. of Water and Environmental Studies, Linkoeping Univ. (Sweden); Allard, B. [Dept. of Water and Environmental Studies, Linkoeping Univ. (Sweden)

    1994-12-31

    The adsorption of europium to colloidal Fe{sub 2}O{sub 3}, FeOOH, Fe(OH){sub 3} and SiO{sub 2} was investigated as a function of pH and the presence of an aquatic fulvic acid (FA). The colloids were present at concentrations repressentative of the upper levels of natural waters (50-500 mg/l). Measurements with Photon Correlation Spectroscopy showed size distribution typically within the ranges 200-700 nm, 40-400 nm and 50-300 nm for Fe{sub 2}O{sub 3}, FeOOH and SiO{sub 2}, respectively, while the amorphous Fe(OH){sub 3} formed relatively large particles (>1000 nm; outside the range of the method for measurements of size distribution). Total concentrations of Eu and the fulvic acid were 10{sup -8} mol l{sup -1} and 2 mg l{sup -1}, respectively. The adsorption was affected by pH, the composition of the colloidal phase as well as the presence of fulvic acid. The uptake was almost quantitative in the Fe-systems at pH>5.5-6, with 50% uptake at pH of 4.5-5.5 (4-5 units below pH{sub zpc}). For quartz, the maximum adsorption was around 90% (at pH 9), with 50% adsorption at pH 7 (4 pH units above pH{sub zpc}). The adsorption can not be related to coulombic attraction between the surfaces and the metal species alone, but rather to a specific chemical adsorption, where the pH-dependence would be related to the distribution of Eu between different species (on the surface and in solution). The presence of FA slightly increased the absorption in the lower pH range, corresponding to an adsorption of Eu-fulvate complexes. The adsorption was reaching 100% at higher pH values in the Fe(OH){sub 3} system, while it was decreased in the other three systems compared to the experiments without FA. The decrease could be attributed to competition between inorganic Eu species and the FA-molecules about sites on the surfaces, an effect not obvious in the Fe(OH){sub 3}-systems due to the much larger surface area available. (orig./MBS)

  5. Effect of the ion force on the hydrolysis constants and of the solubility product of Europium; Efecto de la fuerza ionica sobre las constantes de hidrolisis y del producto de solubilidad del europio

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez R, M.; Ramirez G, J.J.; Solache R, M.; Rojas H, A. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    A study on the behavior of the first hydrolysis constant {beta}{sub Eu,H}{sup l-0} and the constant of the solubility product Kps of the europium in front of the changes of the ion force: 0. 02 M, 0.1 M, 0.7M, 2M, 3M and 4M of sodium perchlorate, at 303 K. Experimentally the potentiometry and also radioactivity measures its were used. The specific interaction of ions theory (SIT) of Bronsted-Guggenheim-Scatchard allows the extrapolation of the values to infinite dilution and the results were: log {beta}{sub Eu,H}{sup l-0} = -7 36 and log K{sub sp}{sup l-0} = -24. 68. A discussion of the group of results with the data of the literature is presented. (Author)

  6. Photoluminescent study of Polycarbonate (PC) and Poly(9-vinylcarbazole) (PVK) doped films with europium complex; Estudo fotoluminescente de filmes de Policarbonato (PC) e Poli(9-vinilcarbazol) (PVK) dopados com complexo de europio

    Energy Technology Data Exchange (ETDEWEB)

    Forster, Pedro Lima

    2010-07-01

    Polymers doped with rare earth complexes are advantaged in film production for many applications in the luminescent field. In this study luminescent polymer obtained from polycarbonate (PC) and poly(9-vinylcarbazole) films doped with diaquatris(thenoyltrifluoroacetonate)europium(III) complex [Eu(tta){sub 3}(H{sub 2}0){sub 2}] were prepared and their calorimetric and luminescent properties in the solid state are reported. The thermal behavior was investigated by differential scanning calorimetry (OSC) and thermogravimetry analysis (TGA). Due of the addition of rare earth Eu(tta){sub 3}(H{sub 2}0){sub 2}] into PC and PVK matrices, changes were observed in the thermal behavior concerning the glass transition and thermal stability. Characteristic broadened narrow bands arising from the {sup 5}D{sub 0} -{yields} {sup 7}F{sub J} transitions (J = 0-4) of Eu{sup 3+} ion indicate the incorporation of the Eu{sup 3+} ions into those polymers. The luminescent films show enhancement emission intensity with an increase in the rare earth concentration in polymeric matrix accompanied by decrease in thermal stability. (author)

  7. Chemiluminescence Determination of Balofloxacin Based on Europium (III)-Sensitized KBrO{sub 3}-Na{sub 2}S{sub 2}O{sub 4} Reaction in Micellar Medium

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Fang; Qi, Yu; Xiong, Wei [Shihezi University, Shihezi (China)

    2012-01-15

    A novel chemiluminescence (CL) flow injection method for the determination of balofloxacin is described. The method is based on the weak CL signal arising from the reaction of KBrO{sub 3} with Na{sub 2}S{sub 2}O{sub 4} in acidic medium being significantly enhanced by balofloxacin in the presence of europium (III) ion and sodium dodecyl benzene sulfonate (SDBS). The experimental conditions that affected CL intensity were carefully optimized and the CL reaction mechanism was briefly discussed. Under the optimum conditions, the relative CL intensity was proportional to the concentration of balofloxacin in the range of 7.0 c 10{sup -11} to 3.0 x 10{sup -7} g mL{sup -1}. The detection limit was 2.7 x 10{sup -11} g mL{sup -1} and the relative standard deviation was 2.1% for 7.0 x 10{sup -10} g mL{sup -1} balofloxacin (n = 13). The proposed method was successfully applied to the determination of balofloxacin in pharmaceutical formulations and biological fluids.

  8. Gold nanoparticle core-europium(iii) chelate fluorophore-doped silica shell hybrid nanocomposites for the lateral flow immunoassay of human thyroid stimulating hormone with a dual signal readout.

    Science.gov (United States)

    Preechakasedkit, Pattarachaya; Osada, Kota; Katayama, Yuta; Ruecha, Nipapan; Suzuki, Koji; Chailapakul, Orawon; Citterio, Daniel

    2018-01-21

    Hybrid nanocomposite particles composed of a gold core coated with a europium(iii)-chelate fluorophore-doped silica shell (AuNPs@SiO 2 -Eu 3+ ) have been synthesized and applied as antibody labels in lateral flow immunoassay (LFIA) devices for the determination of human thyroid stimulating hormone (hTSH). Labeling of monoclonal anti-hTSH antibodies with AuNPs@SiO 2 -Eu 3+ nanocomposites allows for both colorimetric and fluorometric observation of assay results on LFIA devices, relying on visible light absorption due to the localized surface plasmon resonance of the Au-core and the fluorescence emission of the Eu(iii)-chelate-modified shell under UV hand lamp irradiation (365 nm), respectively. The possibility for a dual signal readout provides an attractive alternative for LFIAs: instantaneous naked eye observation of the AuNP colorimetric signal as in conventional LFIAs for hypothyroidism detection, and more sensitive fluorescence detection to assess hyperthyroidism. The limits of detection (LOD) for naked eye observation of LFIA devices are 5 μIU mL -1 and 0.1 μIU mL -1 for the colorimetric and fluorimetric detection, respectively. Using the fluorescence detection scheme in combination with a smartphone and digital color analysis, a quantitative linear relationship between the red intensity and the logarithmic concentration of hTSH was observed (R 2 = 0.988) with an LOD of 0.02 μIU mL -1 . Finally, LFIA devices were effectively applied for detecting hTSH in spiked diluted human serum with recovery values between 100-116%.

  9. A europium- and terbium-coated magnetic nanocomposite as sorbent in dispersive solid phase extraction coupled with ultra-high performance liquid chromatography for antibiotic determination in meat samples.

    Science.gov (United States)

    Castillo-García, M L; Aguilar-Caballos, M P; Gómez-Hens, A

    2015-12-18

    A new magnetic dispersive solid-phase extraction approach based on Eu- and Tb-coated magnetic nanocomposites, combined with ultra-high performance liquid chromatography with fluorometric detection, is reported for the extraction and simultaneous determination of veterinary antibiotics. The method is aimed at monitoring of potential residues of three tetracyclines, namely oxytetracycline, tetracycline, chlortetracycline and three acidic quinolones, such as oxolinic acid, nalidixic acid and flumequine, chosen as model analytes, in animal muscle samples. The nanocomposites were obtained by synthesizing magnetic nanoparticles by a co-precipitation method and their coating with terbium and europium ions. The limits of detection obtained using standard solutions were: 1.0, 1.5, 3.8, 0.25, 0.7 and 1.2ngmL(-1), which corresponds to 3.3, 5.0, 12.7, 0.8, 2.3 and 4.0μgkg(-1) for oxytetracycline, tetracycline, chlortetracycline, oxolinic acid, nalidixic acid and flumequine, respectively, in meat samples. The precision values, obtained in the presence of the sample matrix, were in the ranges 0.12-2.0% and 2.6-15.4% for retention times and areas, respectively. The selectivity of the method was checked by assaying different veterinary drugs, finding that most of them did not interfere at the same concentration levels as that of analytes. A recovery study was performed in the presence of chicken and pork muscle samples, which provided values in the range of 61.5-102.6%. Copyright © 2015 Elsevier B.V. All rights reserved.

  10. Influence of Europium Doping on Various Electrical Properties of Low-Temperature Sintered 0.5Ba0.90Ca0.10TiO3-0.5BaTi0.88Zr0.12O3-0.1%CuO- xEu Lead-Free Ceramics

    Science.gov (United States)

    Tian, Yongshang; Li, Shuiyun; Sun, Shulin; Gong, Yansheng; Li, Tiantian; Yu, Yongshang; Jing, Qiangshan

    2018-01-01

    0.5Ba0.90Ca0.10TiO3-0.5BaTi0.88Zr0.12O3-0.1%CuO- xEu (BCT-BZT-Cu- xEu; x = 0-0.90%) lead-free ceramics were sintered at 1220°C with as-synthesized nanoparticles by a modified Pechini method. The structural characteristics and electrical properties of the ceramics that were influenced by varying europium-doping were investigated. All the ceramics featured high densification (relative density: ˜ 96%). X-ray powder diffraction results indicated the samples possessed pure orthorhombic phase. The maximum relative permittivity ( ɛ r, 10869) was found at x around 0.30%. Europium ions could dope on different substitution sites in the ABO3 lattice, which evidently influenced electrical properties with various volumes of oxygen vacancy. Moreover, the formation mechanisms of oxygen vacancy and defect electron complexes were stated. The piezoelectric properties were impacted by defect electron complexes, internal stress, ionic electronegativity, etc. The optimal electrical properties, i.e., d 33 = 384 pC/N, Q m = 92, and k p = 0.36, were detected at x = 0.45%.

  11. Determination of the stability constants of lanthanum, praseodymium, europium, erbium and lutetium complexes with chloride ions; Determinacion de las constantes de estabilidad de los complejos de lantano, praseodimio, europio, erbio y lutecio con iones cloruro

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez R, E. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2008-07-01

    The stability constants of La{sup 3+}, Pr{sup 3+}, Eu{sup 3+}, Er{sup 3+} and Lu{sup 3+} chloride complexes were determined in perchloric acid media using a liquid-liquid extraction method. The dinonyl napthalene sulfonic acid in n-heptane was used as extractant. The lanthanide (Ln) concentrations were measured by a radiochemical (Eu and Lu) and a spectrophotometric (La, Pr, and Er) methods. In the last method, xylenol orange was used for the determinations at ph 6. The stability constants of lanthanum, praseodymium, erbium and lutetium chloride complexes were determined in 2, 3 and 4 M ionic strength and europium in 1, 2 and 3 M, at 303 K. The fitting of experimental data to the equations for the calculation of the stability constants, was carry out considering both one chemical species (LnCl{sup 2+}) or two chemical species (LnCl{sup 2+} and LnCl{sub 2}{sup +}). The Specific Ion Interaction Theory was applied to the values of log {beta}{sup I}{sub Ln},{sub Cl} and the first stability constants at zero ionic strength were calculated by extrapolation. The same theory could not be applied to the log {beta}{sup I}{sub Ln},{sub 2Cl}, due to its low abundance and the values determined for the stability constants were similar. The distribution diagrams of the chemical species were obtained using the program MEDUSA and considering log {beta}{sup I}{sub Ln},{sub CI}, log {beta}{sup I}{sub Ln},{sub 2CI} values obtained in this work and the hydrolysis constants taken from the literature. The lanthanide chloride complexes are present in solution at specific conditions of ionic strength, concentration and in the absence of hydrolysis. The log {beta}{sup I}{sub Ln},{sub Cl} data were related to the charge density and the corresponding equations were obtained. These equations could be used to determine the stability constants along the lanthanide series. (Author)

  12. NICKEL ALUMINIDE SYNTHESIS REINFORCED WITH MOLYBDENUM BORIDE COMPOSITE

    Directory of Open Access Journals (Sweden)

    Mr. Khosen ф Ri

    2016-06-01

    Full Text Available The authors study obtaining a composite material NiAl - Mo2B5 while carrying out thermally coupled reactions of self-propagating high-temperature synthesis with a deoxidizing aluminothermal stage. The authors established ultimate and phase composition of the obtained composite. The microstructure is studied. It is shown that the composite consists of the intermetallic phase NiAl with Mo2B5 inclusions.

  13. NICKEL ALUMINIDE SYNTHESIS REINFORCED WITH MOLYBDENUM BORIDE COMPOSITE

    OpenAIRE

    Mr. Khosen ф Ri; Mr. Victor V. Gostishchev; Ms. Anastasia V. Medneva; Mr. Sergei N. Khimukhin; Mr. Ivan A. Astapov

    2016-01-01

    The authors study obtaining a composite material NiAl - Mo2B5 while carrying out thermally coupled reactions of self-propagating high-temperature synthesis with a deoxidizing aluminothermal stage. The authors established ultimate and phase composition of the obtained composite. The microstructure is studied. It is shown that the composite consists of the intermetallic phase NiAl with Mo2B5 inclusions.

  14. Fundamental Thermal and Mechanical Properties of Boride Ceramics

    Science.gov (United States)

    2014-02-28

    1600°C and a two-color pyrometer above 1500°C. Heating rates as high as 500°C/min have been achieved. To date, four point bend tests as described by...a two-color optical pyrometer and a programmable PID controller. Water cooled graphite pushrods and a fully articulated graphite 4-point bend...Mechanical Stress Evaluation by Neutrons and Synchrotron Radiation , November 10-12, 2009, Mito, Japan. 20. J. Watts, G.E. Hilmas, and W.G. Fahrenholtz

  15. Development of Boride Composite Materials for Cold Cathode Devices

    Science.gov (United States)

    1981-05-01

    pop. 775, 1979. Johnson, R., "The Lanthanum-Bormn System," J of Phys. Chem, Vol 65, 1961, p. 909. Kanitkar , P., "Field Emissicn Studies of the...Ianthanum HexaborideA’unqsten Sys ," J. Physics D: App!. Phys. Vol 9, 1976 pp L165-LI68. Kanitkar , P. L. "Field Emissicn Studi es of the Lanthanum

  16. Electrochemistry of Europium(III) Chloride in 3 LiCl – NaCl, 3 LiCl – 2 KCl, LiCl – RbCl, and 3 LiCl – 2 CsCl Eutectics at Various Temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Schroll, Cynthia A.; Chatterjee, Sayandev; Levitskaia, Tatiana G.; Heineman, William R.; Bryan, Samuel A.

    2017-01-01

    Here we report the effect of changing the eutectic melt composition on the electrochemical properties of europium(III) chloride under pyroprocessing conditions. The number of electrons transferred, redox potentials and diffusion coefficients were determined using various electrochemical and spectroelectrochemical techniques in four different eutectic mixtures (3 LiCl - NaCl, 3 LiCl - 2 KCl, 3 LiCl - RbCl, and 3 LiCl - 2 CsCl) while varying the temperature of the melt. It was determined that Eu3+ undergoes a one electron reduction to Eu2+ in each melt at all temperatures evaluated. Within all the melts a positive shift in the redox potential as well as an increase in the diffusion coefficient for Eu3+ was observed as the temperature increased. Also observed was a positive shift in the redox potential and increase in the diffusion coefficient for Eu3+ as the weighted average of the cationic radii for the melt decreased.

  17. 10 CFR Appendix C to Part 20 - Quantities 1 of Licensed Material Requiring Labeling

    Science.gov (United States)

    2010-01-01

    ... Samarium-151 10 Samarium-153 100 Samarium-155 1,000 Samarium-156 1,000 Europium-145 100 Europium-146 100 Europium-147 100 Europium-148 10 Europium-149 100 Europium-150 (12.62h) 100 Europium-150 (34.2y) 1 Europium-152m 100 Europium-152 1 Europium-154 1 Europium-155 10 Europium-156 100 Europium-157 100 Europium-158 1...

  18. Progress on the europium neutron capture study using DANCE

    Energy Technology Data Exchange (ETDEWEB)

    Agvaanluvsan, U. [Lawrence Livermore National Laboratory, 7000 East Avenue, P.O. Box 808, L-414, Livermore, CA 94551 (United States)]. E-mail: agvaanluvsan1@llnl.gov; Becker, J.A. [Lawrence Livermore National Laboratory, 7000 East Avenue, P.O. Box 808, L-414, Livermore, CA 94551 (United States); Macri, R.A. [Lawrence Livermore National Laboratory, 7000 East Avenue, P.O. Box 808, L-414, Livermore, CA 94551 (United States); Parker, W. [Lawrence Livermore National Laboratory, 7000 East Avenue, P.O. Box 808, L-414, Livermore, CA 94551 (United States); Wilk, P. [Lawrence Livermore National Laboratory, 7000 East Avenue, P.O. Box 808, L-414, Livermore, CA 94551 (United States); Wu, C.Y. [Lawrence Livermore National Laboratory, 7000 East Avenue, P.O. Box 808, L-414, Livermore, CA 94551 (United States); Bredeweg, T.A.; Esch, E.; Haight, R.C.; O' Donnell, J.M.; Reifarth, R.; Rundberg, R.S.; Schwantes, J.M.; Ullmann, J.L.; Vieira, D.J.; Wilhelmy, J.B.; Wouters, J.M. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Mitchell, G.E.; Sheets, S. [North Carolina State University, Raleigh, NC 27695 (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708 (United States); Becvar, F.; Krticka, M. [Charles University in Prague, CZ 180 00 Prague 8 (Czech Republic)

    2007-08-15

    The accurate measurement of neutron capture cross sections of the Eu isotopes is important for many reasons including nuclear astrophysics and nuclear diagnostics. Neutron capture excitation functions of {sup 151,153}Eu targets were measured recently using a 4{pi} {gamma}-ray calorimeter array DANCE located at the Los Alamos Neutron Science Center for E {sub n} = 0.1-100 keV. The progress on the data analysis efforts is given in the present paper. The {gamma}-ray multiplicity distributions for the Eu targets and Be backing are significantly different. The {gamma}-ray multiplicity distribution is found to be the same for different neutron energies for both {sup 151}Eu and {sup 153}Eu. The statistical simulation to model the {gamma}-ray decay cascade is summarized.

  19. Progress on the Europium Neutron-Capture Study using DANCE

    Energy Technology Data Exchange (ETDEWEB)

    Agvaanluvsan, U; Becker, J A; Macri, R A; Parker, W; Wilk, P; Wu, C Y; Bredeweg, T A; Esch, E; Haight, R C; O' Donnell, J M; Reifarth, R; Rundberg, R S; Schwantes, J M; Ullmann, J L; Vieira, D J; Wilhelmy, J B; Wouters, J M; Mitchell, G E; Sheets, S A; Becvar, F; Krticka, M

    2006-09-05

    The accurate measurement of neutron-capture cross sections of the Eu isotopes is important for many reasons including nuclear astrophysics and nuclear diagnostics. Neutron capture excitation functions of {sup 151,153}Eu targets were measured recently using a 4{pi} {gamma}-ray calorimeter array DANCE located at the Los Alamos Neutron Science Center for E{sub n} = 0.1-100 keV. The progress on the data analysis efforts is given in the present paper. The {gamma}-ray multiplicity distributions for the Eu targets and Be backing are significantly different. The {gamma}-ray multiplicity distribution is found to be the same for different neutron energies for both {sup 151}Eu and {sup 153}Eu. The statistical simulation to model the {gamma}-ray decay cascade is summarized.

  20. Functionalization of sol-gel zirconia composites with europium complexes

    Energy Technology Data Exchange (ETDEWEB)

    Danchova, Nina; Gutzov, Stoyan [Sofia Univ. ' St Kliment Ohridski' (Bulgaria). Dept. of Physical Chemistry

    2014-02-15

    Different sol-gel strategies based on functionalization of ZrO{sub 2}:Eu microparticles with 1,10-phenanthroline (phen) and incorporation of colloidal Eu(phen){sub 2}(NO{sub 3}){sub 3} into zirconia have been used to obtain hybrid sol-gel composites with controlled optical properties. The process leads to materials with quantum yields of about 48 % monitoring the 615 nm emission line at 350 nm excitation. Excitation/luminescence spectroscopy, diffuse reflectance spectroscopy and X-ray diffraction have been used to characterize the hybrid zirconia composites. (orig.)

  1. Interaction of europium and curium with alpha-amylase

    Energy Technology Data Exchange (ETDEWEB)

    Barkleit, Astrid [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Chemistry of the F-Elements; Heller, Anne [Technische Univ. Dresden (Germany). Inst. for Zoology, Molecular Cell Physiology and Endocrinology; Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Biogeochemistry

    2016-07-01

    Time-resolved laser-induced fluorescence spectroscopy (TRLFS) revealed that Eu(III) and Cm(III) form two dominant species with the protein α-amylase (Amy): one with the coordination of a single carboxylate group of the protein and the other with three coordinating carboxylate groups.

  2. Synthesis, characterization, and properties of reduced europium molybdates and tungstates

    Science.gov (United States)

    Abeysinghe, Dileka; Gerke, Birgit; Morrison, Gregory; Hsieh, Chun H.; Smith, Mark D.; Pöttgen, Rainer; Makris, Thomas M.; zur Loye, Hans-Conrad

    2015-09-01

    Single crystals of K0.094Eu0.906MoO4, K0.097Eu0.903WO4, EuWO4, and EuMoO4 were grown from molten chloride fluxes contained in vacuum-sealed fused silica and structurally characterized via single crystal X-ray diffraction. The in situ reduction of Eu3+ to Eu2+ was carried out using Mo, W, and Zn as metal reducing agents. All four compounds crystallize in the tetragonal space group of I41/a and adopt the scheelite (CaWO4) structure type. The magnetic susceptibility of the reported compounds shows paramagnetic behavior down to 2 K. 151Eu Mössbauer spectroscopy was used to analyze the relative Eu2+ and Eu3+ content of the samples. All the compounds were further characterized by EPR, and UV-vis spectroscopy.

  3. Single crystal growth of europium and ytterbium based intermetallic ...

    Indian Academy of Sciences (India)

    to dissolve the excess metal flux. Due to its low melting temperature of 156.6. ◦. C, indium is an ideal metal for use as a reactive flux (self- flux condition). It has widely been used for the synthe- sis and crystal growth of indium-rich binary and ternary indides. In many cases, a slight excess of indium sig- nificantly increases the ...

  4. Electrical and magnetic transport in Strontium doped Europium Ferrimanganites

    Energy Technology Data Exchange (ETDEWEB)

    Abdel-Latif, I.A. [Physics Department, College of Science & Arts, Najran University, P. O. 1988, Najran (Saudi Arabia); Reactor Physics Department, NRC, Atomic Energy Authority, Abou Zabaal P.O. 13759, Cairo (Egypt); Ahmed, Mahrous R. [Physics Department, Faculty of Science, Sohag University, Sohag 82524 (Egypt); Physics Department, Aljamoum University College, Um-Elqura University, Makka (Saudi Arabia); Al-Omari, I.A.; Sellai, A. [Physics Department, Faculty of Science, Soltan Qaboos University, P.O. Box 36, PC 123, Muscatt (Oman)

    2016-12-15

    Eu{sub 0.65}Sr{sub 0.35}Fe{sub x}Mn{sub 1−x}O{sub 3} (x=0.1, 0.3 and 0.5) has been prepared using a standard solid state reaction method. The under-investigation compounds is found to crystallize in a single-phase orthorhombic structure in the P{sub bnm} space group (62). The adiabatic polaron electronic transfer was obtained for all samples and the activation energy of x=0.1 sample is equal to 1.013 meV and slightly increase at x=0.3 (1.289 meV) while is doubled for x=0.5 to be 2.1065 meV. The magnetization–temperature dependence measurements of Eu{sub 0.65}Sr{sub 0.35}Fe{sub x}Mn{sub 1−x}O{sub 3} show the ferromagnetic ordering at low iron concentration x=0.1 and when iron concentration increase to x=0.5 the noncollinear magnetic ordering (the canted antiferromagnetic) is obtained. The magnetic phase transition (paramagnetic-ferromagnetic transition) in the Eu{sub 0.65}Sr{sub 0.35}Fe{sub 0.1}Mn{sub 0.9}O{sub 3} is observed at T{sub c} of 150 K. For Eu{sub 0.65}Sr{sub 0.35}Fe{sub 0.5}Mn{sub 0.5}O{sub 3} the multi-magnetic phase transition is observed at T{sub c} of 200K and T{sub N} of 430 K. The resistivity at low temperature is measured. Theoretical Calculations using Monte Carlo code have been done. The magnetization as function of temperature has been calculated using Monte Carlo simulations for Eu{sub 0.65}Sr{sub 0.35}Fe{sub x}Mn{sub 1−x}O{sub 3} (x=0.0, 0.1, 0,2, 0.3, 0.4 and 0.5). Ising model is a suitable model to study the magnetization for our compounds. The internal energy for x=0 is the highest value compared with the other x values which have nearly a ground state value equal to 2.7 J. - Highlights: • The distortion parameter in the crystal structure of Eu{sub 0.65}Sr{sub 0.35}Fe{sub x}Mn{sub 1−x}O{sub 3} increase with increasing concentration of iron and affected both electrical and magnetic transport. • The density of electrons over the unit cell decrease with increasing the iron concentration and thus give rise to the decrease in electrical conductivity and the change of the magnetic ordering. • The transition from thermal activation mechanism at temperature higher than room temperature into adiabatic polaron mechanism at temperature lower than room temperature in all samples. • The transition from the soft FM ordering at low iron concentration x=0.1 into the harder canted FM ordering with x>0.3. • The internal energy calculation showed the highest value of x=0, compared with the other x values, which have nearly a ground state value equal to 2.7 J.

  5. Synthesis and characterization of europium doped LiF phosphor

    Energy Technology Data Exchange (ETDEWEB)

    Villalobos, M. L.; Vallejo, M. A.; Sosa A, M. [Universidad de Guanajuato, Division de Ciencias e Ingenierias, Loma del Bosque No. 103, Lomas del Campestre, 37150 Leon, Guanajuato (Mexico); Diaz T, L. A., E-mail: villaloboscm2010@licifug.ugto.mx [Centro de Investigaciones en Optica, A. C., Loma del Bosque No. 115, Lomas del Campestre, 37150 Leon, Guanajuato (Mexico)

    2015-10-15

    LiF with different dopants has been one of the most investigated materials to use as thermoluminescent dosimeter. In this paper, we present the preparation method, the characterization and the thermoluminescent response of Eu doped LiF irradiated with X-rays. Pure and Eu doped LiF samples with different dopant concentration (0, 0.25, 0.5, 0.75 and 1 % mol) were synthesized using the precipitation method. The samples were structurally characterized by X-ray diffraction (XRD), the diffraction patterns showed a main cubic crystalline structure and a secondary hexagonal structure. The photoluminescence spectrum exhibited four well defined peaks characteristic of the Eu{sup 3+} ion. Thermoluminescent (Tl) glow curves of x-ray irradiated samples showed a well-defined single peak around 200 degrees C, except for the pure and 0.25% Eu doped samples. (Author)

  6. Effect of pressure on the phonon properties of europium ...

    Indian Academy of Sciences (India)

    Unknown

    phonon density of states and compared them with the first order Raman scattering results. The calculation of ... raman et al 1974). The structural phase transition pre- ssures for EuO, EuS, EuSe and EuTe are 30–40 GPa,. 22 GPa, 15 GPa and 10 GPa, respectively. ... †Paper presented at the 5th IUMRS ICA98, October 1998,.

  7. High pressure annealing of Europium implanted GaN

    KAUST Repository

    Lorenz, K.

    2012-02-09

    GaN epilayers were implanted with Eu to fluences of 1×10^13 Eu/cm2 and 1×10^15 Eu/cm2. Post-implant thermal annealing was performed in ultra-high nitrogen pressures at temperatures up to 1450 ºC. For the lower fluence effective structural recovery of the crystal was observed for annealing at 1000 ºC while optical activation could be further improved at higher annealing temperatures. The higher fluence samples also reveal good optical activation; however, some residual implantation damage remains even for annealing at 1450 ºC which leads to a reduced incorporation of Eu on substitutional sites, a broadening of the Eu luminescence lines and to a strongly reduced fraction of optically active Eu ions. Possibilities for further optimization of implantation and annealing conditions are discussed.© (2012) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

  8. Hyperfine interactions at europium sites in oxide glasses

    Science.gov (United States)

    Concas, G.; Congiu, F.; Muntoni, C.; Bettinelli, M.; Speghini, A.

    1996-03-01

    The shape of the γ resonance absorption peak of the Eu3+ ion in a disordered structure was investigated in some phosphate, borate, and silicate glasses by using 151Eu Mössbauer spectroscopy. The quality of the fits was tested by using the Durbin-Watson d statistics. The observed full width at half maximum of the peak was resolved in a contribution of the broadening and a contribution of the quadrupole splitting, due to the distortion of the Eu site compared to a cubic symmetry. The Eu-O bond was found to have a covalent admixture with 6s character. The axial component of the electric-field gradient at the Eu site was found to be correlated with the optical basicity of the glass.

  9. Interaction of europium and curium with alpha-amylase.

    Science.gov (United States)

    Barkleit, Astrid; Heller, Anne; Ikeda-Ohno, Atsushi; Bernhard, Gert

    2016-06-07

    The complexation of Eu(iii) and Cm(iii) with the protein α-amylase (Amy), a major enzyme in saliva and pancreatic juice, was investigated over wide ranges of pH and concentration at both ambient and physiological temperatures. Macroscopic sorption experiments demonstrated a strong and fast binding of Eu(iii) to Amy between pH 5 and 8. The protein provides three independent, non-cooperative binding sites for Eu(iii). The overall association constant of these three binding sites on the protein was calculated to be log K = 6.4 ± 0.1 at ambient temperature. With potentiometric titration, the averaged deprotonation constant of the carboxyl groups (the aspartic and glutamic acid residues) of Amy was determined to be pKa = 5.23 ± 0.14 at 25 °C and 5.11 ± 0.24 at 37 °C. Time-resolved laser-induced fluorescence spectroscopy (TRLFS) revealed two different species for both Eu(iii) and Cm(iii) with Amy. In the case of the Eu(iii) species, the stability constants were determined to be log β11 = 4.7 ± 0.2 and log β13 = 12.0 ± 0.4 for Eu : Amy = 1 : 1 and 1 : 3 complexes, respectively, whereas the values for the respective Cm(iii) species were log β11 = 4.8 ± 0.1 and log β13 = 12.1 ± 0.1. Furthermore, the obtained stability constants were extrapolated to infinite dilution to make our data compatible with the existing thermodynamic database.

  10. On the abundance of Europium. [in Ap and Am stars

    Science.gov (United States)

    Hartoog, M. R.; Cowley, C. R.; Adelman, S. J.

    1974-01-01

    The inclusion of the effects of hyperfine splitting can significantly lower the abundance estimate of Eu from singly ionized lines which lie on the flat portion of the curve of growth. In the 21 cool Ap stars studied by Adelman and the five Am stars studied by Smith, the Eu abundance was reduced by 0.4 dex on the average. In individual cases, the reductions were as great as 0.9 dex. This makes the Eu abundance comparable to that of its neighboring rare earths Sm and Gd in the Ap stars and less than Sm and Gd in the Am stars, but still substantially overabundant with respect to solar values.

  11. Europium (III) and americium (III) stability constants with humic acid

    Energy Technology Data Exchange (ETDEWEB)

    Torres, R.A.; Choppin, G.R.

    1984-01-01

    The stability constants for tracer concentrations of Eu(III) and Am(III) complexes with a humic acid extracted from a lake-bottom sediment were measured using a solvent extraction system. The organic extractant was di(2-ethylhexyl)-phosphoric acid in toluene while the humate aqueous phase had a constant ionic strength of 0.1 M (NaClO/sub 4/). Aqueous humic acid concentrations were monitored by measuring uv-visible absorbances at approx.= 380 nm. The total carboxylate capacity of the humic acid was determined by direct potentiometric titration to be 3.86 +- 0.03 meq/g. The humic acid displayed typical characteristics of a polyelectrolyte - the apparent pKsub(a), as well as the calculated metal ion stability constants increased as the degree of ionization (..cap alpha..) increased. The binding data required a fit of two stability constants, ..beta../sub 1/ and ..beta../sub 2/, such that for Eu, log ..beta../sub 1/ = 8.86 ..cap alpha.. + 4.39, log ..beta../sub 2/ = 3.55 ..cap alpha.. + 11.06 while for Am, log ..beta../sub 1/ = 10.58 ..cap alpha.. + 3.84, log ..beta../sub 2/ = 5.32 ..cap alpha.. + 10.42. With hydroxide, carbonate, and humate as competing ligands, the humate complex associated with the ..beta../sub 1/ constant is calculated to be the dominant species for the trivalent actinides and lanthanides under conditions present in natural waters.

  12. Microstructure and properties of gravity sintered 316l stainless steel powder with nickel boride addition

    Directory of Open Access Journals (Sweden)

    Božić Dušan

    2016-01-01

    Full Text Available The present work demonstrates a procedure for synthesis of stainless steel powder by gravity sintering method. As an additive to the basic powder, NiB powder was added in the amount of 0.2 - 1.0 wt.%. Gravity sintering was done in vacuum, at the temperatures of 1100°C-1250°C, in the course of 3 - 60 min, using ceramic mould. Structural characterization was conducted by XRD, and microstructural analysis by optical and scanning electron microscope (SEM. Mechanical properties were investigated by tensile tests with steel rings. Density and permeability were determined by standard techniques for porous samples. Gravity sintered stainless steel with NiB addition had more superior mechanical and physico-chemical properties compared to stainless steel obtained by standard powder metallurgy procedures - pressing and sintering. [Projekat Ministarstva nauke Republike Srbije, br. 172005

  13. Manganese mono-boride, an inexpensive room temperature ferromagnetic hard material

    Science.gov (United States)

    Ma, Shuailing; Bao, Kuo; Tao, Qiang; Zhu, Pinwen; Ma, Teng; Liu, Bo; Liu, Yazhou; Cui, Tian

    2017-03-01

    We synthesized orthorhombic FeB-type MnB (space group: Pnma) with high pressure and high temperature method. MnB is a promising soft magnetic material, which is ferromagnetic with Curie temperature as high as 546.3 K, and high magnetization value up to 155.5 emu/g, and comparatively low coercive field. The strong room temperature ferromagnetic properties stem from the positive exchange-correlation between manganese atoms and the large number of unpaired Mn 3d electrons. The asymptotic Vickers hardness (AVH) is 15.7 GPa which is far higher than that of traditional ferromagnetic materials. The high hardness is ascribed to the zigzag boron chains running through manganese lattice, as unraveled by X-ray photoelectron spectroscopy result and first principle calculations. This exploration opens a new class of materials with the integration of superior mechanical properties, lower cost, electrical conductivity, and fantastic soft magnetic properties which will be significant for scientific research and industrial application as advanced structural and functional materials.

  14. Manganese mono-boride, an inexpensive room temperature ferromagnetic hard material

    OpenAIRE

    Shuailing Ma; Kuo Bao; Qiang Tao; Pinwen Zhu; Teng Ma; Bo Liu; Yazhou Liu; Tian Cui

    2017-01-01

    We synthesized orthorhombic FeB-type MnB (space group: Pnma) with high pressure and high temperature method. MnB is a promising soft magnetic material, which is ferromagnetic with Curie temperature as high as 546.3?K, and high magnetization value up to 155.5?emu/g, and comparatively low coercive field. The strong room temperature ferromagnetic properties stem from the positive exchange-correlation between manganese atoms and the large number of unpaired Mn 3d electrons. The asymptotic Vickers...

  15. Manganese mono-boride, an inexpensive room temperature ferromagnetic hard material.

    Science.gov (United States)

    Ma, Shuailing; Bao, Kuo; Tao, Qiang; Zhu, Pinwen; Ma, Teng; Liu, Bo; Liu, Yazhou; Cui, Tian

    2017-03-06

    We synthesized orthorhombic FeB-type MnB (space group: Pnma) with high pressure and high temperature method. MnB is a promising soft magnetic material, which is ferromagnetic with Curie temperature as high as 546.3 K, and high magnetization value up to 155.5 emu/g, and comparatively low coercive field. The strong room temperature ferromagnetic properties stem from the positive exchange-correlation between manganese atoms and the large number of unpaired Mn 3d electrons. The asymptotic Vickers hardness (AVH) is 15.7 GPa which is far higher than that of traditional ferromagnetic materials. The high hardness is ascribed to the zigzag boron chains running through manganese lattice, as unraveled by X-ray photoelectron spectroscopy result and first principle calculations. This exploration opens a new class of materials with the integration of superior mechanical properties, lower cost, electrical conductivity, and fantastic soft magnetic properties which will be significant for scientific research and industrial application as advanced structural and functional materials.

  16. Oxidation behavior of multiphase molybdenum-molybdenum silicide-molybdenum silicide boride intermetallics

    Science.gov (United States)

    Dheeradhada, Voramon Supatarawanich

    Multiphase Mo-Mo3Si-Mo5SiB2(T2) alloys of various compositions and microstructures were investigated for oxidation resistance at 800 and 1300°C. The alloys varied in Si/B ratio from 1:1 to 1:2 and their microstructures were processed to have the Mo phase distributed as a continuous phase or as discrete particles. At 800°C, the alloys exhibited poor oxidation resistance regardless of Si/B ratio or their microstructures. Oxide scale consisted of MoO 3 and boron-containing glass. Alloys with lower Si/B ratio yielded silicate glass with lower viscosity that resulted in lower weight loss compared to the high Si/B ratio alloys. Intermediate layers of Mo and Mo-Si-O were observed adjacent to Mo5SiB2 and Mo3Si phases, respectively. At 1300°C, the multiphase alloys developed a protective glass scale with an intermediate layer of (Mo+glass) between the base alloy and outer glass scale. Boron-lean silicate glass was essential for the protection from further oxidation. For oxidation resistance at 1300°C, alloys require a high Si/B ratio. In terms of microstructures, the multiphase alloys consisting of small Mo particles uniformly dispersed in fine spacing of silicide phases provide better oxidation resistance than the alloys with continuous Mo dendrites. Glass preferentially formed at Mo3Si rather than at T2 phase. Vapor-solid diffusion experiments were carried out with single phase alloys containing either Mo3Si or T2 as the major phase, and the multiphase Mo-10Si-10B(at%) alloy. The alloys were exposed to vacuum to induce silicon loss resulting in the formation of a Mo layer. In addition, microprobe analysis was carried out for the determination of composition profiles across the (Mo+glass) layer and the external glass scale formed on the Mo-13.2Si-13.2B (at%) alloy oxidized at 1300°C. The microprobe data were analyzed for interdiffusion fluxes and interdiffusion coefficients with the aid of a computer program called "MultiDiFlux (c)". The effective interdiffusion coefficients for Mo, Si, B, and O in various phases were also determined. The motion of the (metal/Mo+glass) and (Mo+glass/glass) interfaces was examined. An average effective interdiffusion coefficient of silicon in molybdenum at 1300°C was estimated as 10 -17 m2/s. Moreover, interdiffusion coefficients for each component in the Mo+glass layer were evaluated on the basis of Mishin's analysis.

  17. Formation of molybdenum boride cermet coating by the detonation spray process

    Science.gov (United States)

    Yang, Gao; Zu-Kun, Hei; Xiaolei, Xu; Gang, Xin

    2001-09-01

    The effects of the powder particle size and the acetylene/oxygen gas flow ratio during the detonation spray process on the amount of molybdenum phase, porosity, and hardness of the coatings using MoB powder were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), etc. The results show that the presence of metallic molybdenum in the coating results from decomposition of MoB powder during thermal spray. The compositions of the coatings are metallic Mo, MoB, and Mo2B, which are different from the phases of the original powder. The amount of molybdenum phase increases monotonously with the oxygen/acetylene ratio, but the increasing rate for the fine powder is faster than that for the coarse powder. The porosity and hardness of the coating are related to the amount of molybdenum phase. The phase constitution of the coating is discussed.

  18. The Physics and Chemistry of carbides, Nitrides and Borides. Volume 185

    Science.gov (United States)

    1990-01-01

    orbits around the axial field lines. Near the substrate, the ECR resonance conditions allow the electrons to receive resonance impulses during each... orbit so these electrons acquire a higher energy than electrons 141 elsewhere in the cavity. Thus, the plasma forms preferentially in the region of these...34frittage et caracterisation de cdramiques dans le syst me zirconium- carbone-oxyg~ne", E.N.S. Mines de Saint-Etienne, (1986), Thtse (n* 54 C.I.). [102

  19. Boride ceramics covalent functionalization and its effect on the thermal conductivity of epoxy composites

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Zhi-Qiang, E-mail: yuzhiqiang@fudan.edu.cn [Department of Materials Science, Fudan University, 200433 Shanghai (China); Wu, Yicheng [Department of Materials Science, Fudan University, 200433 Shanghai (China); Wei, Bin; Baier, Horst [Institute of Lightweight Structures, Technical University Munich (TUM), Boltzmannstr. 15, D-85747 Garching (Germany)

    2015-08-15

    Zirconium diboride/aluminium oxide (ZrB{sub 2}/Al{sub 2}O{sub 3}) composite particles were functionalized with epoxide functionalized γ-glycidoxypropyltrimethoxysilane by the covalent bonding approach to improve the interfacial compatibility of composite particles in epoxy matrix. The composites of epoxy resin filled with functionalized ZrB{sub 2}/Al{sub 2}O{sub 3} were prepared by in situ bulk condensation polymerization of bisphenol A and epichlorohydrin in the presence of ZrB{sub 2}/Al{sub 2}O{sub 3}. The heat-conducting properties of composites were investigated by the finite element method (FEM) and the thermal conductivity test. The finite-element program ANSYS was used for this numerical analysis, and three-dimensional spheres-in-cube lattice array models were built to simulate the microstructure of composite materials for different filler contents. The thermal conductivity of composites was determined by laser flash method (LFA447 Nanoflash), using the measured heat capacity and thermal diffusivity, with separately entered density data. The results show that the effective chemical bonds are formed between ZrB{sub 2}/Al{sub 2}O{sub 3} and γ-glycidoxypropyltrimethoxysilane after the surface functionalization. The interfacial compatibility and bonding of modified particles with the epoxy matrix are improved. The thermal conductivities of functionalized composites with 3 vol% and 5 vol% loading are increased by 8.3% and 12.5% relative to the unmodified composites, respectively. Comparison of experimental values and calculated values of the thermal conductivity, the average relative differences are under 5%. The predictive values of thermal conductivity of epoxy composites are in reasonable agreement with the experimental values. - Highlights: • The surfaces of ZrB{sub 2}/Al{sub 2}O{sub 3} were functionalized by silane coupling agents. • The thermal conductivity (TC) of modified epoxy composites is improved significantly. • The FEM values of TC are in reasonable agreement with the experimental values.

  20. Improving Hardness and Toughness of Boride Composites Based on AIMgB14

    Energy Technology Data Exchange (ETDEWEB)

    Peters, Justin Steven [Iowa State Univ., Ames, IA (United States)

    2007-01-01

    The search for new super-hard materials has usually focused on strongly bonded, highly symmetric crystal structures similar to diamond. The two hardest single-phase materials, diamond and cubic boron nitride (cBN), are metastable, and both must be produced at high temperatures and pressures, which makes their production costly. In 2000, a superhard composite based on a low-symmetry, boron-rich compound was reported. Since then, many advances have been made in the study of this AlMgB14-TiB2 composite. The composite has been shown to exhibit hardness greater than either of its constituent phases, relying on its sub-micron microstructure to provide hardening and strengthening mechanisms. With possible hardness around 40 GPa, an AlMgB14 - 60 vol% TiB2 approaches the hardness of cBN, yet is amenable to processing under ambient pressure conditions. There are interesting aspects of both the AlMgB14 and TiB2 phases. AlMgB14 is comprised of a framework of boron, mostly in icosahedral arrangements. It is part of a family of 12 known compounds with the same boron lattice, with the metal atoms replaced by Li, Na, Y or a number of Lanthanides. Another peculiar trait of this family of compounds is that every one contains a certain amount of intrinsic vacancies on one or both of the metal sites. These vacancies are significant, ranging from 3 to 43% of sites depending on the composition. TiB2 is a popular specialty ceramic material due to its high hardness, moderate toughness, good corrosion resistance, and high thermal and electrical conductivity. The major drawback is the difficulty of densification of pure TiB2 ceramics. A combination of sintering aids, pressure, and temperatures of 1800 C are often required to achieve near full density articles. The AlMgB14 - TiB2 composites can achieve 99% density from hot-pressing at 1400 C. This is mostly due to the preparation of powders by a high-energy milling technique known as mechanical alloying. The resulting fine powders have high activity, and Fe from wear debris acts as a sintering aid. Mechanical alloying improves the sinterability of the composite material, it has the same effect on pure TiB2. TiB2 processed by high-energy milling has been found to achieve 99% theoretical density at 1400 C with the addition of ~1 wt% Fe. Both the AlMgB14 - TiB2 composites and pure TiB2 produced from these methods have enhanced mechanical properties due to their fine microstructures. These materials show exceptional promise in the field of wear resistance. This includes cutting tools, erosion resistant coatings, and low-friction sliding contacts to name a few. Under certain wear conditions, the composite material can show performance on par with that of current high-end cBN and WC materials tailored for wear resistance. The composite material also exhibits low reactivity with Ti alloys, a pre-requisite for effective machining of these alloys, a trait that few hard materials possess.

  1. Ground State Structures of Boron-Rich Rhodium Boride: An Ab Initio Study

    Science.gov (United States)

    Chu, Bin-Hua; Zhao, Yuan; Yan, Jin-Liang; Li, Da

    2018-01-01

    Not Available Supported by the Natural Science Foundation of Shandong Province under Grant Nos ZR2016AP02, ZR2016FM38 and ZR2016EMP01, the Innovation Project of Ludong University under Grant No LB2016013, the Open Project of State Key Laboratory of Superhard Materials of Jilin University under Grant No 201605, and the National Natural Science Foundation of China under Grant Nos 11704170 and 61705097.

  2. Research and Development on Titanium Alloys

    Science.gov (United States)

    1949-10-31

    are being prepared by the Norton Company for evaluation. Titanium boride , tantalum boride , zirconium boride , tungsten boride , and molybdenum boride ...alloying additionO will be ex- tended. 9 Ternary alloys of manganese and carbon, manganese and vanadium, and molybdenum and tungsten, prepared by...graphite crucibles lined with tantalum carbide and turgsten boride as refractories for molten titanium,. Melts were prepared In crucibles made of zirconium

  3. Electrical and magnetic properties of several ruthenates and superconductivity in magnesium boride and MgCNi(3)

    Science.gov (United States)

    He, Tao

    2002-09-01

    Perovskite-based ruthenates have been receiving considerable attention both because of their interesting and variable magnetic properties, and because of the discovery of exotic superconductivity in the layered ruthenate Sr 2RuO4. Another perovskite, SrRuO3, is the only known oxide ferromagnet with a 4d transition metal, and magnetism is easily suppressed by Ca doping. The suppression of ferromagnetic interactions in SrxCa1-xRuO3 has frequently been attributed to the orthorhombic structural distortion, either through the crossover to classical antiferromagnetic interactions, or, alternatively, to a nearly ferromagnetic metal. This study reports the comparison of the magnetic properties of Srx(Na0.5La0.5)1-xRuO 3 to SrxCa1-xRuO3, showing that there is a much faster suppression of ferromagnetic interactions in the former case. Neither orthorhombic distortion nor cation size disorder can explain the observed difference. Instead, the difference may be attributed to charge disorder on the A-site, which greatly affects the local environment of Ru atoms and leads to the faster suppression of the long-range ferromagnetic state. The magnetic ground state of perovskite structure CaRuO3 has been enigmatic for decades. This study also shows that paramagnetic CaRuO 3 can be made ferromagnetic by very small amounts of partial substitution of Ru by various transition metals. The results are consistent with the recent proposal that CaRuO3 is not a classical antiferromagnet, but rather is poised at a critical point between ferromagnetic and paramagnetic ground states. Ti, Fe, Mn and Ni doping result in ferromagnetic behavior. The second part of this thesis is on the superconductivity of MgB 2 and MgCNi3. Since the discovery of superconductivity in MgB2 in January 2001, detailed information on its properties has been rapidly accumulated. The reported properties, the very simple structure, and the commercial availability of this material make MgB2 a favorite candidate for large scale and electronic applications. In thin film fabrication, the reactivity of MgB2 with substrate materials or insulating or metallic layers in multi-layer circuits is an important factor. In this work the reactivity of MgB2 with powdered forms of common substrate and electronic materials is studied. Some oxides and nitrides prove to be potentially good substrates for making thin films, while others, including some commonly used substrates like Al2O3, SrTiO 3, and SiO2, have serious chemical compatibility problems. In the latter case, caution should be taken when fabricating thin films. This thesis also describes the discovery of superconductivity at 8 K in the perovskite structure compound MgCNi3. This material is the three-dimensional analogue of the LnNi2B2C family of superconductors, which have Tcs up to 16K. The itinerant electrons in both LnNi2B2C and MgCNi3 are based on partial filling of Ni d-states, which generally leads to ferromagnetism, as is the case in metallic Ni. The very high relative proportion of Ni in MgCNi3 is especially suggestive of the possible importance of magnetic interactions in the superconductivity, and, further, the lower Tc of the three-dimensional compound is contrary to conventional ideas.

  4. Catalytic Reductions and Tandem Reactions of Nitro Compounds Using in Situ Prepared Nickel Boride Catalyst in Nanocellulose Solution.

    Science.gov (United States)

    Prathap, Kaniraj Jeya; Wu, Qiong; Olsson, Richard T; Dinér, Peter

    2017-09-15

    A mild and efficient method for the in situ reduction of a wide range of nitroarenes and aliphatic nitrocompounds to amines in excellent yields using nickel chloride/sodium borohydride in a solution of TEMPO-oxidized nanocellulose in water (0.01 wt %) is described. The nanocellulose has a stabilizing effect on the catalyst, which increases the turnover number and enables low loading of nickel catalyst (0.1-0.25 mol % NiCl2). In addition, two tandem protocols were developed in which the in situ formed amines were either Boc-protected to carbamates or further reacted with an epoxide to yield β-amino alcohols in excellent yields.

  5. Multiple Electron Charge Transfer Chemistries for Electrochemical Energy Storage Systems: The Metal Boride and Metal Air Battery

    Science.gov (United States)

    Stuart, Jessica F.

    The primary focus of this work has been to develop high-energy capacity batteries capable of undergoing multiple electron charge transfer redox reactions to address the growing demand for improved electrical energy storage systems that can be applied to a range of applications. As the levels of carbon dioxide (CO2) increase in the Earth's atmosphere, the effects on climate change become increasingly apparent. According to the Energy Information Administration (EIA), the U.S. electric power sector is responsible for the release of 2,039 million metric tons of CO2 annually, equating to 39% of total U.S. energy-related CO2 emissions. Both nationally and abroad, there are numerous issues associated with the generation and use of electricity aside from the overwhelming dependence on fossil fuels and the subsequent carbon emissions, including reliability of the grid and the utilization of renewable energies. Renewable energy makes up a relatively small portion of total energy contributions worldwide, accounting for only 13% of the 3,955 billion kilowatt-hours of electricity produced each year, as reported by the EIA. As the demand to reduce our dependence on fossils fuels and transition to renewable energy sources increases, cost effective large-scale electrical energy storage must be established for renewable energy to become a sustainable option for the future. A high capacity energy storage system capable of leveling the intermittent nature of energy sources such as solar, wind, and water into the electric grid and provide electricity at times of high demand will facilitate this transition. In 2008, the Licht Group presented the highest volumetric energy capacity battery, the vanadium diboride (VB2) air battery, exceedingly proficient in transferring eleven electrons per molecule. This body of work focuses on new developments to this early battery such as fundamentally understanding the net discharge mechanism of the system, evaluation of the properties and performance of nanoscopic anodic materials in addition to the previously developed macroscopic system, as well as the exploration of a high-energy capacity TiB 2/VB2 composite anode. However, the greatest challenge to this room temperature VB2 primary battery is to develop a means to electrochemically recharge the anodic material (how to reinsert the eleven electrons per molecule that are removed during the battery's discharge). Rechargeable batteries, such as the new molten air battery presented in this thesis, offer a high intrinsic capacity mode for energy storage and overcome problems such as the need for higher energy capacity, cost-effective batteries for a range of electronic, transportation, and large-scale power storage devices. Molten air batteries presented and discussed in this work are viable systems that provide a means to electrochemically recharge the VB2-air battery and deliver large-scale energy storage due to their scalability, location flexibility, construction from readily available resources, and offer increased energy storage capacity for the electric grid. One example is the VB2 molten air battery, which discharges according to: VB 2 + 11/4 O2 → 1/ 2 V2O5 + B2O3 (1). Previously, our group has shown that carbon dioxide can be captured from atmospheric air concentrations at solar efficiencies as high as 50%, and that carbon dioxide emissions associated with the production of several commodities can be electrochemically avoided in by the Solar Thermal Electrochemical Process (STEP). Utilizing this process, the carbon molten air battery relies on carbon dioxide directly from the air: Charging: CO2 (g) → C (solid) + O2 (g) (2) Discharging: C (solid) + O2 (g) → CO2 (g) (3). More specifically, in a molten carbonate electrolyte containing added oxide, such as lithium carbonate with lithium oxide, the four-electron charging reaction, Equation 2, approaches 100% faradic efficiency and can be described as the following two equations: O2- (dissolved) + CO2 (g) → CO 32- (molten) (2a) CO32- (molten) ?→ C (solid) + O2 (g) + O2- (dissolved) (2b). Thus, powered by the oxidation of carbon formed directly from the CO 2 in our earth's atmosphere, the carbon molten air battery is a viable system to provide large-scale energy storage. These batteries are rechargeable and have amongst the highest intrinsic battery storage capacities available. The electron charge transfer chemistry is demonstrated through three examples. These examples utilize iron, carbon, and vanadium diboride as reactive materials, each containing intrinsic volumetric energy capacities of 10,000 Wh/L for Fe to Fe (III), 19,000 Wh/L for C to CO2, and 27,000 Wh/L for VB2 to B2O3 and V2O 5, compared to 6,200 Wh/L for the lithium air battery.

  6. Synthesis and characterization of titania-based monodisperse fluorescent europium nanoparticles for biolabeling

    Energy Technology Data Exchange (ETDEWEB)

    Tan Mingqian [Department of Analytical Chemistry, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Graduate School of the Chinese Academy of Sciences, Dalian 116023 (China); Wang Guilan [Department of Analytical Chemistry, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Graduate School of the Chinese Academy of Sciences, Dalian 116023 (China); Ye Zhiqiang [Department of Analytical Chemistry, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Graduate School of the Chinese Academy of Sciences, Dalian 116023 (China); Yuan Jingli [Department of Analytical Chemistry, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Graduate School of the Chinese Academy of Sciences, Dalian 116023 (China)]. E-mail: jingliyuan@yahoo.com.cn

    2006-03-15

    Inorganic-organic hybrid titania-based nanoparticles covalently bound to a fluorescent Eu{sup 3+} chelate of 4,4'-bis(1'',1'',1'',2'',2'',3'',3''-heptafluoro-4'',6''-hexanedion-6''-yl) chlorosulfo-o-terphenyl (BHHCT-Eu{sup 3+}) were synthesized by a sol-gel technique. A conjugate of BHHCT with 3-[2-(2-aminoethylamino) ethylamino]propyl-trimethoxysilane (APTS) was used as a precursor for the nanoparticle preparation and monodisperse nanoparticles consisting of titania network and silica sub-network covalently bound to the Eu{sup 3+} chelate were prepared by the copolymerization of APTS-BHHCT conjugate, titanium tetraisopropoxide (TTIP) and free APTS in EuCl{sub 3} water-alcohol solution. The effects of reaction conditions on size and fluorescence lifetime of the nanoparticles were investigated. The characterizations by transmission electron microscopy and fluorometric methods indicate that the nanoparticles are near spherical and strongly fluorescent having a fluorescence quantum yield of 11.6% and a long fluorescence lifetime of {approx}0.4 ms. The direct-introduced amino groups on the nanoparticle's surface by using free APTS in nanoparticle preparation facilitated the biolabeling process of the nanoparticles. The nanoparticle-labeled streptavidin (SA) was prepared and used in a sandwich-type time-resolved fluoroimmunoassay (TR-FIA) of human prostate-specific antigen (PSA) by using a 96-well microtiter plate as the solid phase carrier. The method gives a detection limit of 66 pg/ml for the PSA assay.

  7. Photoactive europium(III) centered mesoporous hybrids with 2-thenoyltrifluoroacetone functionalized SBA-16 and organic polymers.

    Science.gov (United States)

    Li, Yajuan; Yan, Bing

    2010-03-14

    A series of novel ternary organic-inorganic mesoporous polymeric hybrids TTFA-S16-Eu-PMMA, TTFA-S16-Eu-PMAA, and TTFA-S16-Eu-PVP (TTFA = 2-Thenoyltrifluoroacetone; PMMA = polymethyl methacrylate; PMAA = polymethacrylic acid; PVP = polyvinylpyrrolidone) have been assembled by the Eu(3+) complex covalently attaching to the TTFA directly functionalized ordered mesoporous SBA-16 and organic polymer. FTIR, UV, XRD, TEM, N(2) adsorption measurements, photoluminescent spectra, and TG plots were characterized, and the results reveal that they all have high surface area, uniformity in the mesostructure, and good crystallinity. In addition, the ternary rare earth mesoporous polymeric hybrids show an overall increase in luminescent lifetime and quantum efficiency compared to binary rare earth mesoporous hybrid TTFA-S16-Eu, especially the mesoporous hybrid with PVP exhibits the highest luminescence quantum efficiency and longest lifetime.

  8. Electroluminescence of a device based on europium {beta}-diketonate with phosphine oxide complex

    Energy Technology Data Exchange (ETDEWEB)

    Quirino, W.G. [LOEM - Department of Physics - Pontificia Universidade Catolica do Rio de Janeiro, PUC-Rio - P.O.Box 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil); Adati, R.D. [Institute of Chemistry, Sao Paulo State OYiversity - UNESP, P.O.Box. 355, Araraquara, SP, CEP 14801-970 (Brazil); Lima, S.A.M. [Institute of Chemistry, Sao Paulo State OYiversity - UNESP, P.O.Box. 355, Araraquara, SP, CEP 14801-970 (Brazil); Legnani, C. [LOEM - Department of Physics - Pontificia Universidade Catolica do Rio de Janeiro, PUC-Rio - P.O.Box 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil); Jafelicci, M. [Institute of Chemistry, Sao Paulo State OYiversity - UNESP, P.O.Box. 355, Araraquara, SP, CEP 14801-970 (Brazil); Davolos, M.R. [Institute of Chemistry, Sao Paulo State OYiversity - UNESP, P.O.Box. 355, Araraquara, SP, CEP 14801-970 (Brazil); Cremona, M. [LOEM - Department of Physics - Pontificia Universidade Catolica do Rio de Janeiro, PUC-Rio - P.O.Box 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil)]. E-mail: cremona@fis.puc-rio.br

    2006-11-23

    Rare earth (RE) ions have spectroscopic characteristics to emit light in narrow lines, which makes RE complexes with organic ligands candidates for full color OLED (Organic Light Emitting Diode) applications. In particular, {beta}-diketone rare earth (RE{sup 3+}) complexes show high fluorescence emission efficiency due to the high absorption coefficient of the {beta}-diketone and energy transfer to the central ion. In this work, the fabrication and the electroluminescent properties of devices containing a double and triple-layer OLED using a new {beta}-diketone complex, [Eu(bmdm){sub 3}(tppo){sub 2}], as transporting and emitting layers are compared and discussed. The double and triple-layer devices based on this complex present the following configurations respectively: device 1: ITO/TPD (40 nm)/[Eu(bmdm){sub 3}(tppo){sub 2}] (40 nm)/Al (150 nm); device 2: ITO/TPD (40 nm)/[Eu(bmdm){sub 3}(tppo){sub 2}] (40 nm)/Alq{sub 3} (20 nm)/Al (150 nm) and device 3: ITO/TPD (40 nm)/bmdm-ligand (40 nm)/Al (150 nm), were TPD is (N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1-biphenil-4,4-diamine) and bmdm is butyl methoxy-dibenzoyl-methane. All the films were deposited by thermal evaporation carried out in a high vacuum system. These devices exhibit high intensity photo- (PL) and electro-luminescent (EL) emission. Electroluminescence spectra show emission from Eu{sup 3+} ions attributed to the {sup 5}D{sub 0} to {sup 7}F {sub J} (J = 0, 1, 2, 3 and 4) transitions with the hypersensitive {sup 5}D{sub 0} {sup {yields}} {sup 7}F{sub 2} transition (around 612 nm) as the most prominent one. Moreover, a transition from {sup 5}D{sub 1} to {sup 7}F{sub 1} is also observed around 538 nm. The OLED light emission was almost linear with the current density. The EL CIE chromaticity coordinates (X = 0.66 and Y = 0.33) show the dominant wavelength, {lambda} {sub d} = 609 nm, and the color gamut achieved by this device is 0.99 in the CIE color space.

  9. Self-assembly of a helical zinc-europium complex: speciation in aqueous solution and luminescence

    Directory of Open Access Journals (Sweden)

    Emmanuel eDeiters

    2013-09-01

    Full Text Available Two new tridentate(NNO-bidentate(NN compartmental ligands, HL5 and HL6, are synthesized from pyridine and benzimidazole synthons. They react in aqueous solution under physiological conditions with ZnII, LnIII, or a mixture thereof, to yield complexes of different stoichiometries, 1:3, 2:2, 2:3, 1:1:3, the speciation of which is established by UV-visible titrations and ESI mass spectrometry. Photophysical studies of the EuIII-containing solutions in Tris-HCl 0.1 M (pH = 7.4 show that lanthanide luminescence arises from a unique N6O3 coordination site with pseudo D3 symmetry. Relevant parameters such as crystal field splitting, lifetime, radiative lifetime and intrinsic quantum yield perfectly match those reported for dinuclear 4f-4f helicates in which the EuIII ion has the same coordination environment.

  10. Stabilizing divalent europium in aqueous solution using size-discrimination and electrostatic effects.

    Science.gov (United States)

    Regueiro-Figueroa, Martín; Barriada, José Luis; Pallier, Agnès; Esteban-Gómez, David; Blas, Andrés de; Rodríguez-Blas, Teresa; Tóth, Éva; Platas-Iglesias, Carlos

    2015-05-18

    We report two macrocyclic ligands containing a 1,10-diaza-18-crown-6 fragment functionalized with either two picolinamide pendant arms (bpa18c6) or one picolinamide and one picolinate arm (ppa18c6(-)). The X-ray structure of [La(ppa18c6)(H2O)](2+) shows that the ligand binds to the metal ion using the six donor atoms of the crown moiety and the four donor atoms of the pendant arms, 11-coordination being completed by the presence of a coordinated water molecule. The X-ray structure of the [Sr(bpa18c6)(H2O)](2+) was also investigated due to the very similar ionic radii of Sr(2+) and Eu(2+). The structure of this complex is very similar to that of [La(ppa18c6)(H2O)](2+), with the metal ion being 11-coordinated. Potentiometric measurements were used to determine the stability constants of the complexes formed with La(3+) and Eu(3+). Both ligands present a very high selectivity for the large La(3+) ion over the smaller Eu(3+), with a size-discrimination ability that exceeds that of the analogous ligand containing two picolinate pendant arms reported previously (bp18c6(2-)). DFT calculations using the TPSSh functional and the large-core pseudopotential approximation provided stability trends in good agreement with the experimental values, indicating that charge neutral ligands derived from 1,10-diaza-18-crown-6 enhance the selectivity of the ligand for the large Ln(3+) ions. Cyclic voltammetry measurements show that the stabilization of Eu(2+) by these ligands follows the sequence bp18c6(2-) stability against oxidation than the aquated ion, for which an E1/2 value of -585 mV has been measured.

  11. Some light-ion excitation-function measurements on titanium, yttrium, and europium, and associated results

    Energy Technology Data Exchange (ETDEWEB)

    West, H.I. Jr. [ed.; Lanier, R.G.; Mustafa, M.G.; Nuckolls, R.M.; Nagle, R.J.; O`Brien, H. [Lawrence Livermore National Lab., CA (United States); Frehaut, J.; Adam, A.; Philis, C. [Service de Physique et Techniques Nucleaires, Centre d`Etudes Bruyeres-le-Chatel, Boite Postale 12 (France)

    1993-11-01

    This report discusses: Fabrication of Plastic-Matrix-Encapsulated Accelerator Targets and Their Use in Measuring Nuclear Excitation Functions; Correcting Excitation Function Data in the Low Energy Region for Finite Thickness of the Target Foils, Including Effects of Straggling; Excitation Functions for the Nuclear Reactions on Titanium Leading to the Production {sup 48}V, {sup 44}Sc and {sup 47}Sc by Proton, Deuteron and Triton Irradiations at 0--35 MeV; Some Excitation Functions of Proton and Deuteron Induced Reactions on {sup 89}Y; Measurements of the Excitation Functions of the Isobaric Chain {sup 87}Y, {sup 87}Y{sup m}, {sup 87}Y{sup g} and {sup 87}Sr{sup m}; Levels in {sup 87}Y Observed in the Decay of {sup 87}Zr; and Nuclear Reaction Excitation Functions from the Irradiation of {sup 151,153}Eu with Protons And deuterons up to 35 MeV.

  12. Performance of Europium-Doped Strontium Iodide, Transparent Ceramics and Bismuth-loaded Polymer Scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Cherepy, N J; Payne, S A; Sturm, B W; O' Neal, S P; Seeley, Z M; Drury, O B; Haselhorst, L K; Rupert, B L; Sanner, R D; Thelin, P A; Fisher, S E; Hawrami, R; Shah, K S; Burger, A; Ramey, J O; Boatner, L A

    2011-08-30

    Recently discovered scintillators for gamma ray spectroscopy, single crystal SrI{sub 2}(Eu), GYGAG(Ce) transparent ceramic and Bismuth-loaded plastics, offer resolution and fabrication advantages compared to commercial scintillators, such as NaI(Tl) and standard PVT plastic. Energy resolution at 662 keV of 2.7% is obtained with SrI{sub 2}(Eu), while 4.5% is obtained with GYGAG(Ce). A new transparent ceramic scintillator for radiographic imaging systems, GLO(Eu) offers high light yield of 70,000 Photons/MeV, high stopping, and low radiation damage. Implementation of single crystal SrI{sub 2}(Eu), Gd-based transparent ceramics, and Bi-loaded plastic scintillators can advance the state-of-the art in ionizing radiation detection systems.

  13. Synthesis and characterization of the europium (III) complex as an organic luminescent material

    Energy Technology Data Exchange (ETDEWEB)

    Zhuo Zuliang; Zhang Fujun; Xu Zheng; Lu Lifang; Li Junming; Wang Yongsheng [Key Laboratory of Luminescence and Optical Information (Beijing Jiaotong University), Ministry of Education, Beijing 100044 (China); Lv Yuguang, E-mail: fjzhang@bjtu.edu.c [The Provincial Key Laboratory of Biomaterials, College of Chemistry and Pharmacy, Jiamusi University, Jiamusi 154007 (China)

    2010-11-15

    The red emission organic material Eu(coumarin){sub 3{center_dot}}2H{sub 2}O complex was synthesized and its morphology, energy level alignment and luminescence characteristics were studied by using scanning electron microscopy, Fourier transform infrared spectra, cyclic voltammetry and ultraviolet-visible absorption spectra and fluorescence spectra. Eu(coumarin){sub 3{center_dot}}2H{sub 2}O shows bright red emission originating from Eu{sup 3+} ions under 345 nm light excitation. The luminescence lifetime of Eu{sup 3+} in this complex is about 580 {mu}s. To improve the quality of Eu(coumarin){sub 3{center_dot}}2H{sub 2}O thin films, Eu(coumarin){sub 3{center_dot}}2H{sub 2}O was doped with a poly(N-vinylcarbazole) (PVK) solution. The organic materials 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) and aluminum quinoline (Alq{sub 3}) were used as hole-blocking and electron-transporting layers in our fabricated electroluminescence (EL) devices on indium tin oxide (ITO) substrates, respectively. The EL devices ITO/poly-(3,4-ethylenedioxythiophene):poly-(styrenesulphonic acid) (PEDOT:PSS)/emitting layer (PVK:Eu)/BCP/Alq{sub 3}/Al were fabricated, and EL spectra were measured under different driving voltages. There is one emission peaking at 490 nm in addition to the characteristic emission peaks of Eu{sup 3+}, which should be attributed to the spectral overlap between the PVK emission and electroplex emission originating from PVK and BCP interfaces. This explanation can be positively supported by the dependence of the EL spectral variation of ITO/ PVK/BCP/Alq{sub 3}/Al devices on the driving voltage.

  14. Pulsed laser deposition of europium-doped multilayer thin films for spectral storage applications

    Science.gov (United States)

    Bezares, Francisco J.

    This thesis studies different Eu optical centers in MgS:Eu and CaS:Eu thin films produced by Chemically Controlled Pulse Laser Deposition (CCPLD) and evaluates their suitability for the development of spectral storage devices of the future. The produced thin films consist of one or more optically active layer(s), MgS:Eu, CaS:Eu or a similar material, and a corresponding ZnS capping layer that functions as a protecting barrier for the other layers and preserves their composition and integrity. Given that the synthesis of the materials used to produce the multilayer structures in this work proved a great challenge, careful attention was given to the optimization of all fabrication parameters. Mass Spectrometry was used during the deposition of the thin films and the data obtained resulted on improvements and optimization of the deposition process. Scanning electron microscopy studies of these thin films were conducted to study degradation upon long-term storage. Microscopy results show that the morphology of the produced thin films is correlated to the growth environment during deposition and deterioration of the deposited materials could be initiated by nano-gaps and cracks in the capping layer of the thin films. In addition to optical centers in MgS:Eu and CaS:Eu, new centers were created by changing the thin film growth environment inside a hi-vacuum chamber, modifying the composition of the ablation target material, or both. For example, introducing O2--, or alternatively HCl, inside the CCPLD chamber while producing MgS:Eu thin films results in the formation of impurity associated centers across lattice sites throughout the deposited structures. In another method of impurity doping studied, Cl-- and Na+ were introduced into the MgS:Eu and CaS:Eu lattices by mixing trace amounts of the impurity ions into these materials in polycrystalline form and making this mixture a deposition target by hi-pressure cold compression technique. The introduction of these impurity ions will alter the crystal field environment around the Eu ions thus creating new optical centers with a shift in energy of their characteristic Zero Phonon Line. After extensive characterization of the optical properties of the thin films produced, laser-induced fluorescence spectroscopy and absorption spectroscopy measurements confirm that they are suitable candidates to be used in conjunction with power-gated spectral holeburning technique and could potentially provide ultrahigh, terabits per square inch, storage densities.

  15. Comparing the 2,2'-Biphenylenedithiophosphinate Binding of Americium with Neodymium and Europium.

    Science.gov (United States)

    Cross, Justin N; Macor, Joseph A; Bertke, Jeffery A; Ferrier, Maryline G; Girolami, Gregory S; Kozimor, Stosh A; Maassen, Joel R; Scott, Brian L; Shuh, David K; Stein, Benjamin W; Stieber, S Chantal E

    2016-10-04

    Advancing our understanding of the minor actinides (Am, Cm) versus lanthanides is key for developing advanced nuclear-fuel cycles. Herein, we describe the preparation of (NBu4 )Am[S2 P((t) Bu2 C12 H6 )]4 and two isomorphous lanthanide complexes, namely one with a similar ionic radius (i.e., Nd(III) ) and an isoelectronic one (Eu(III) ). The results include the first measurement of an Am-S bond length, with a mean value of 2.921(9) Å, by single-crystal X-ray diffraction. Comparison with the Eu(III) and Nd(III) complexes revealed subtle electronic differences between the complexes of Am(III) and the lanthanides. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Effect of europium content on physical properties of In2O3 thin films ...

    Indian Academy of Sciences (India)

    Author Affiliations. O KAMOUN1 A BOUKHACHEM1 C MRABET1 A YUMAK1 P PETKOVA1 K BOUBAKER1 M AMLOUK1. Unité de Physique des Dispositifs à Semi-conducteurs, Faculté des Sciences de Tunis, Université de Tunis El Manar, 2092 Tunis, Tunisia ...

  17. Sorption behavior of cesium, cobalt and europium radionuclides onto hydroxyl magnesium silicate

    Energy Technology Data Exchange (ETDEWEB)

    Hamed, Mostafa M.; Holiel, M.; Ahmed, I.M. [Atomic Energy Authority, Cairo (Egypt). Hot Laboratories and Waste Management Center

    2016-07-01

    The radioactive wastes from different activities have to be safely disposed of and isolated from the human environment. The retardation of radioactive materials by designed barriers is originally controlled by the sorption ability of the mineral compositions. In this work, a naturally available mineral composite, a hydroxyl magnesium silicate (HMS) was investigated as potential natural inorganic sorbent for the retention of long-lived radionuclides ({sup 134}Cs, {sup 60}Co and {sup 152+154}Eu) from aqueous solutions. The factors affecting the sorption process, such as contact time and pH were evaluated. Furthermore X-ray fluorescence (XRF), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), X-ray diffraction (XRD), differential thermal and thermogravimetry analyses (DTA/TGA) measurements were examined in order to assess the physicochemical properties of the magnesium silicate mineral. Langmuir and Freundlich isotherms fitted the result s substantially better than the Flory-Huggins isotherm and the sorption was found to follow pseudo-first order kinetic model. The proposed mineral has been successfully applied for the sorption of {sup 134}Cs, {sup 60}Co and {sup 152+154}Eu radionuclides from real radioactive waste. The results indicated that about 97.4-99% of {sup 134}Cs, {sup 60}Co and {sup 152+154}Eu radionuclides were efficiently retained onto the HMS mineral. Based on the results obtained, it can be concluded that the HMS mineral is an economic and efficient retaining material for environmental hazardous migration and/or leakage of some radionuclides such as {sup 134}Cs, {sup 60}Co and {sup 152+154}Eu and trivalent actinide ({sup 241}Am, {sup 242m}Am and {sup 243}Am) ions. Therefore, this study could be used as a starting point to establish and consider that mineral as an engineered barrier around the disposal facilities at the nuclear activity centres.

  18. Optical Spectroscopy of Europium doped Gallium Nitride prepared by Solid Source Molecular Beam Epitaxy

    Science.gov (United States)

    Nyein, Ei Ei; Seo, J. T.; Bluiett, A.; Anderson, J.; Hommerich, U. H.; Heikenfeld, J.; Garter, M.; Lee, D. S.; Steckl, A. J.

    2001-04-01

    Thin Film Electroluminescence Displays (TEFL’s) are all solid-state devices and offer several advantages over well known LCD’s including increased brightness and viewing angle. We are currently investigating Eu doped GaN as a potential red phosphor for TEFL display applications. Eu doped GaN films were grown by solid source molecular beam epitaxy on Si (111) substates. The material was optically characterized through temperature dependent emission spectroscopy using a He-Cd laser at 325 nm for above band gap excitation. A strong red emission was obtained at 622 nm, which corresponds to an Eu^3+ inner 4f-shell transition from the ^5D 0 to ^7F2 state. A temperature dependent study of the red Eu^3+ line showed that the integrated emission intensity decreased by roughly a factor of 20 between 77K and room temperature. On the contrary, the emission lifetime changed only slightly ( 10-20non-radiative decay processes are small. Therefore, the observed thermal quenching of red Eu emission is assigned to a strongly temperature dependent pumping process.

  19. Identification of defect-trap-related europium sites in gallium nitride

    Energy Technology Data Exchange (ETDEWEB)

    Fleischman, Z.; Tafon, P.S.; Dierolf, V. [Physics Department, Lehigh University, 16 Memorial Drive East, Bethlehem, PA 18015 (United States); Munasinghe, C.; Steckl, A.J. [Nanoelectronics Laboratory, University of Cincinnati, Cincinnati, OH 45221 (United States)

    2007-03-15

    We performed site-selective combined excitation-emission spectroscopy (CEES) studies on Eu-doped GaN layers grown using Interrupted Growth Epitaxy (IGE). We identified numerous Eu{sup 3+} incorporation sites, which exhibit different relative emission intensities as the growth conditions are varied. We found defect-trap related Eu sites that can be excited over a wide spectral range and that dominate the photoluminescence spectra for above-bandgap excitation. Spectra obtained through above-bandgap excitation, which simulates EL operation, are identical to the emission spectra of these defect-trap related sites, indicating that these particular Eu ions would be the major contributors to electroluminescent (EL) emission in these samples. In resonant excitation, however, the emission from these sites is rather weak suggesting that these are minority sites. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  20. Experimental Study and modelling of the Sorption of Selenite and Europium Onto Smectite and Illite Clays

    Energy Technology Data Exchange (ETDEWEB)

    Missana, T.; Alonso, U.; Garcia-Gutierrez, M.

    2009-10-12

    This study provides a large set of experimental selenite sorption data for pure smectite and illite. Similar sorption behavior existed in both clays: linear within a large range of the Se concentrations investigated and independent of ionic strength. Selenite sorption was also analysed in the illite/smectite system with the clays mixed in two different proportions. The objective of the study was to provide the simplest model possible to fit the experimental data, a model also capable of describing selenite sorption in binary illite/smectite clay systems. Selenite sorption data were modeled using both a one-and a two-site non-electrostatic model that took into account the formation of two complexes at the edge sites of the clay. The complexation constants obtained by fitting sorption data of the individual minerals were incorporated into a model to predict the adsorption of selenium in the illite/ smectite mixtures; the models predictions were consistent with the experimental adsorption data. (Author) 42 refs.

  1. Effect of europium content on physical properties of In2O3 thin films ...

    Indian Academy of Sciences (India)

    During the deposition process, the precursor mixture flow rate was taken constantly at 4 ml min. −1 ... TC(hkl) calculated values of the doped In2O3 thin films are given in table 1. Figure 2. X-ray diffraction spectra of ... wavelength of CuKα radiation, β1/2 the full-width at half- maximum of each peaks and θ the Bragg angle.

  2. Sequential multiple-step europium ion implantation and annealing of GaN

    KAUST Repository

    Miranda, S. M C

    2014-01-20

    Sequential multiple Eu ion implantations at low fluence (1×1013 cm-2 at 300 keV) and subsequent rapid thermal annealing (RTA) steps (30 s at 1000 °C or 1100 °C) were performed on high quality nominally undoped GaN films grown by metal organic chemical vapour deposition (MOCVD) and medium quality GaN:Mg grown by hydride vapour phase epitaxy (HVPE). Compared to samples implanted in a single step, multiple implantation/annealing shows only marginal structural improvement for the MOCVD samples, but a significant improvement of crystal quality and optical activation of Eu was achieved in the HVPE films. This improvement is attributed to the lower crystalline quality of the starting material, which probably enhances the diffusion of defects and acts to facilitate the annealing of implantation damage and the effective incorporation of the Eu ions in the crystal structure. Optical activation of Eu3+ ions in the HVPE samples was further improved by high temperature and high pressure annealing (HTHP) up to 1400 °C. After HTHP annealing the main room temperature cathodo- and photoluminescence line in Mg-doped samples lies at ∼ 619 nm, characteristic of a known Mg-related Eu3+ centre, while after RTA treatment the dominant line lies at ∼ 622 nm, typical for undoped GaN:Eu. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. On the response of a europium doped phosphor-coated CMOS digital imaging detector

    Energy Technology Data Exchange (ETDEWEB)

    Seferis, I.E. [Department of Medical Physics, Faculty of Medicine, University of Patras, 26500 Patras (Greece); Michail, C.M.; Valais, I.G.; Fountos, G.P.; Kalyvas, N.I. [Department of Medical Instruments Technology, Technological Educational Institute (TEI) of Athens, Agios Spyridonos, 12210 Athens (Greece); Stromatia, F. [Department of Radiology and Nuclear Medicine, “IASO” General Hospital, Mesogion 264, 15562 Holargos (Greece); Oikonomou, G. [Department of Medical Radiological Technology, Faculty of Health and Caring Professions, Technological Educational Institute (TEI) of Athens, Agios Spyridonos, 12210 Athens (Greece); Kandarakis, I.S., E-mail: kandarakis@teiath.gr [Department of Medical Instruments Technology, Technological Educational Institute (TEI) of Athens, Agios Spyridonos, 12210 Athens (Greece); Panayiotakis, G.S. [Department of Medical Physics, Faculty of Medicine, University of Patras, 26500 Patras (Greece)

    2013-11-21

    Purpose: The purpose of the present study was to assess the information content of a high resolution active pixel CMOS imaging sensor coupled to Gd{sub 2}O{sub 2}S:Eu phosphor screens in terms of single index image quality metrics such as the information capacity (IC) and the noise equivalent passband (Ne). Methods: The CMOS sensor was coupled to two Gd{sub 2}O{sub 2}S:Eu scintillator screens with coating thicknesses of 33.3 and 65.1 mg/cm{sup 2}. IC and Ne were obtained by means of experimentally determined parameters such as the modulation transfer function (MTF), the detective quantum efficiency (DQE) and the noise equivalent quanta (NEQ). Measurements were performed using the standard IEC-RQA5 radiation beam quality (70 kVp) and a W/Rh beam quality (28 kVp). Results: It was found that the detector response function was linear for the exposure ranges under investigation. At 70 kVp, under the RQA 5 conditions IC values were found to range between 1730 and 1851 bits/mm{sup 2} and Ne values were found between 2.28 and 2.52 mm{sup −1}. At 28 kVp the corresponding IC values were found to range between 2535 and 2747 bits/mm{sup 2}, while the Ne values were found between 5.91 and 7.09 mm{sup −1}. Conclusion: IC and Ne of the red emitting phosphor/CMOS sensor combination were found with high values suggesting an acceptable imaging performance in terms of information content and sharpness, for X-ray digital imaging. -- Highlights: •Gd{sub 2}O{sub 2}S:Eu/CMOS combination has comparable image quality parameters to Gd{sub 2}O{sub 2}S:Tb/CMOS. •Information capacity was found with high values suggesting an acceptable imaging performance. •Red emitting phosphors coupled to silicon based optical sensors could be used in developing efficient imaging detectors.

  4. Europium underneath graphene on Ir(111): Intercalation mechanism, magnetism, and band structure

    Science.gov (United States)

    Schumacher, Stefan; Huttmann, Felix; Petrović, Marin; Witt, Christian; Förster, Daniel F.; Vo-Van, Chi; Coraux, Johann; Martínez-Galera, Antonio J.; Sessi, Violetta; Vergara, Ignacio; Rückamp, Reinhard; Grüninger, Markus; Schleheck, Nicolas; Meyer zu Heringdorf, Frank; Ohresser, Philippe; Kralj, Marko; Wehling, Tim O.; Michely, Thomas

    2014-12-01

    The intercalation of Eu underneath Gr on Ir(111) is comprehensively investigated by microscopic, magnetic, and spectroscopic measurements, as well as by density functional theory. Depending on the coverage, the intercalated Eu atoms form either a (2 ×2 ) or a (√{3 }×√{3 }) R 30∘ superstructure with respect to Gr. We investigate the mechanisms of Eu penetration through a nominally closed Gr sheet and measure the electronic structures and magnetic properties of the two intercalation systems. Their electronic structures are rather similar. Compared to Gr on Ir(111), the Gr bands in both systems are essentially rigidly shifted to larger binding energies resulting in n doping. The hybridization of the Ir surface state S1 with Gr states is lifted, and the moiré superperiodic potential is strongly reduced. In contrast, the magnetic behavior of the two intercalation systems differs substantially, as found by x-ray magnetic circular dichroism. The (2 ×2 ) Eu structure displays plain paramagnetic behavior, whereas for the (√{3 }×√{3 }) R 30∘ structure the large zero-field susceptibility indicates ferromagnetic coupling, despite the absence of hysteresis at 10 K. For the latter structure, a considerable easy-plane magnetic anisotropy is observed and interpreted as shape anisotropy.

  5. Transport of europium colloids in vadose zone lysimeters at the semiarid Hanford site.

    Science.gov (United States)

    Liu, Ziru; Flury, Markus; Zhang, Z Fred; Harsh, James B; Gee, Glendon W; Strickland, Chris E; Clayton, Ray E

    2013-03-05

    The objective of this study was to quantify transport of Eu colloids in the vadose zone at the semiarid Hanford site. Eu-hydroxy-carbonate colloids, Eu(OH)(CO3), were applied to the surface of field lysimeters, and migration of the colloids through the sediments was monitored using wick samplers. The lysimeters were exposed to natural precipitation (145-231 mm/year) or artificial irrigation (124-348 mm/year). Wick outflow was analyzed for Eu concentrations, supplemented by electron microscopy and energy-dispersive X-ray analysis. Small amounts of Eu colloids (colloids under both natural precipitation and artificial irrigation; that is, the leading edge of the Eu colloids moved at a velocity of 3 cm/day within the first 2 months after application. Episodic infiltration (e.g., Chinook snowmelt events) caused peaks of Eu in the wick outflow. While a fraction of Eu moved consistent with long-term recharge estimates at the site, the main mass of Eu remained in the top 30 cm of the sediments. This study illustrates that, under field conditions, near-surface colloid mobilization and transport occurred in Hanford sediments.

  6. A comparative study of europium, thorium and uranium binding to an aquatic fulvic acid

    Energy Technology Data Exchange (ETDEWEB)

    Norden, M.; Ephraim, H.J.; Allard, B. [Linkoeping Univ. (Sweden); Albinsson, Y. [Chalmers Univ. of Technology, Goeteborg (Sweden)

    1993-12-31

    Advances in safe management and disposal of radioactive waste have shown that a comprehensive program requires the incorporation of dissolved organics into radwaste and transport effluent models, with respect to their binding of radionuclides. The binding of Eu{sup 3+}, Th{sup 4+} and UO{sub 2}{sup 2+} to a well-characterized aquatic fulvic acid has been studied using an ultrafiltration method at a bulk electrolyte concentration of 0.10 M NaClO{sub 4}, trace amounts of radionuclides and fulvic acid concentrations of 60 and 120 mg/l. The results expressed as the overall complex formation function, {beta}{sub ov}, versus pH show the following order: Th{sup 4+} > Eu{sup 3+} > UO{sub 2}{sup 2+}. The estimated {beta}{sub 0v} values have been discussed by considering the aqueous chemistry of Eu{sup 3+}, Th{sup 4+} and UO{sub 2}{sup 2+} vis-a-vis the solution chemistry of the fulvic acid sample.

  7. Lithium ionophore VIII as an extraordinarily strong receptor for the trivalent europium cation

    Science.gov (United States)

    Makrlík, Emanuel; Novák, Vít; Vaňura, Petr

    2015-01-01

    On the basis of extraction experiments and γ-activity measurements, the extraction constant corresponding to the equilibrium Eu3+(aq) + 3A-(aq) + 1(nb) ⇆ 1.Eu3+(nb) + 3A-(nb) occurring in the two-phase water-nitrobenzene system (A- = CF3SO-3; 1 = lithium ionophore VIII; aq = aqueous phase, nb = nitrobenzene phase) was determined as log Kex (1.Eu3+, 3A-) = 2.5 ± 0.1. Furthermore, the extremely high stability constant of the 1.Eu3+ complex in nitrobenzene saturated with water was calculated: log βnb (1.Eu3+) = 15.6 ± 0.1. Finally, by using DFT calculations, the most probable structure of the cationic complex species 1.Eu3+ was derived. In the resulting complex, the 'central' cation Eu3+ is bound by six very strong bond interactions to the corresponding six oxygen atoms of the parent ligand 1. It is evident that this exceptionally effective receptor 1 for the Eu3+ cation could be considered as a potential extraction agent for nuclear waste treatment.

  8. [Markers for Immunofluorescence Analysis Based on Europium Complex with Fluorinated β-Diketones Carbazole Series].

    Science.gov (United States)

    Kostryukova, T S; Ivanovskaya, N P; Zatonsky, G V; Osin, N S; Vasilev, N V

    2015-01-01

    In order to develop new markers for immunofluorescence time-resolved luminescence analysis tetraketodiester carbazole series was obtained. Compound contains methoxycarbonyl reactive groups, separated from the 1,3-dicarbonyl chelating fragment by difluoromethylene spacers (CF2)4. Complexes of this compound with the ions Eu3+ are stable in aqueous solution and possess a long-living intensive luminescence with the main peaks: emission--in the area of 615 nm and excitation--in the 380-390 nm, that distinguishes them from most used analogues. Conjugate of streptavidin to compound was obtained and its fluorescent spectral characteristics allow to use it as a universal reagent for various schemes of biological microanalysis.

  9. Measurements of the luminescence lifetimes of Europium (III) ion in nitrilotriacetic acid (NTA) aqueous solution system

    Science.gov (United States)

    Stryla, Zdzislaw; Lis, S.; Hnatejko, Z.; Elbanowski, M.

    1995-03-01

    Time-resolved laser induced fluorescence spectroscopy has been used to study complexation of Eu(III) ion with nitrilotriacetic acid (NTA). An experimental setup consisting of the nitrogen laser pumped tunable dye laser and two different detection devices has been built and extensively tested. Using this apparatus, the lifetimes of the 5D0 level of Eu(III) ion in complexes with NTA in water solution for 2:1, 1:1, 1:2 Eu:NTA molar ratios over the wide pH range have been measured.

  10. Crystallization kinetics and optical properties of titanium-lithium tetraborate glass containing europium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Mohamed, E.A. [Al Azhar University, Department of Physics, Faculty of Science (Girl' s Branch), Cairo (Egypt); Ratep, A. [Ain Shams University, Physics Department, Faculty of Girls, Cairo (Egypt); Abdel-Khalek, E.K.; Kashif, I. [Al-Azhar University, Department of Physics, Faculty of Science, Cairo (Egypt)

    2017-07-15

    The crystallization kinetics and optical properties of [60 Li{sub 2}B{sub 4}O{sub 7}-30 TiO{sub 2}-10 Eu{sub 2}O{sub 3}] (mol%) glass sample have been investigated. The present glass sample exhibits three crystallization exothermic peaks (T{sub p1}, T{sub p2,} and T{sub p3}) corresponding to the formation of LiBO{sub 2}, Li{sub 2}B{sub 4}O{sub 7,} and EuTiO{sub 3} phases, respectively. The presence of phase separation in the glass sample has been confirmed by scanning electron microscopic (SEM). The mean values of Avrami exponent (n = 3.1 and 4) around T{sub p1} and T{sub p2}, indicate that the bulk crystallization with a constant number of nuclei and with an increasing number of nuclei, respectively. The values of the local activation energy as a function of the fraction of crystallization (0.1 ≤ χ ≤ 0.9) decrease for the crystallization of LiBO{sub 2} and EuTiO{sub 3} and increase for the crystallization of Li{sub 2}B{sub 4}O{sub 7}. The values of n(χ) for T{sub p3} and T{sub p2} in the range (0.1 ≤ χ ≤ 0.9) and (0.1 ≤ χ ≤ 0.4), respectively, are larger than 4 indicate that the presence of anomalous in Avrami exponent. The trend of Judd-Ofelt intensity parameters (Ω{sub 2} > Ω{sub 4} > Ω{sub 6}) and the bonding parameter (δ) indicate that the lower symmetry and the highest covalent nature of the bonding around Eu{sup 3+} ions. (orig.)

  11. The insulating-to-superconducting transition in europium high-temperature superconducting ceramics

    CERN Document Server

    Rosenbaum, R

    1997-01-01

    Experiment resistivity data on high-temperature superconducting ceramics of fully oxygenated EuBa sub 2 Cu sub 3 sub - sub x Co sub x O sub y show that the insulating-to-superconducting transitions take place at liquid-helium temperature, provided that the cobalt fraction x exceeds 0.3. The resistivity follows a simple power-law dependence rho propor to T sup - sup 1 sup / sup 2 , attributed to electron-electron interactions. A model based upon intrinsic Josephson tunnelling junctions is suggested to explain the transition from insulating to superconducting states. (author)

  12. DNA interaction of europium(III) complex containing 2,2'-bipyridine and its antimicrobial activity.

    Science.gov (United States)

    Jahani, Shohreh; Khorasani-Motlagh, Mozhgan; Noroozifar, Meissam

    2016-01-01

    The interaction of native fish salmon DNA (FS-DNA) with [Eu(bpy)3Cl2(H2O)]Cl, where bpy is 2,2'-bipyridine, is studied at physiological pH in Tris-HCl buffer by spectroscopic methods, viscometric techniques as well as circular dichroism (CD). These experiments reveal that Eu(III) complex has interaction with FS-DNA. Moreover, binding constant and binding site size have been determined. The value of Kb has been defined 2.46 ± .02 × 10(5) M(-1). The thermodynamic parameters are calculated by Van't Hoff equation, the results show that the interaction of the complex with FS-DNA is an entropically driven phenomenon. CD spectroscopy followed by viscosity as well as fluorescence and UV--Vis measurements indicate that the complex interacts with FS-DNA via groove binding mode. Also, the synthesized Eu(III) complex has been screened for antimicrobial activities.

  13. EPR measurement of the effect of glass composition on the oxidation states of europium

    Science.gov (United States)

    Morris, R. V.; Haskin, L. A.

    1974-01-01

    An investigation was conducted concerning the dependence of the concentration ratio of Eu(2+) to Eu(3+) on composition for silicate liquids whose compositional end members are CaAl2Si2O8 and MgSiO3, MG2SiO4, CaMgSi2O6, CaMgSiO4, CaSiO3, or Ca2SiO4. The liquids were quenched to produce glasses. An electron paramagnetic resonance spectrometer was used to determine the concentration ratios of Eu(2+) to Eu(3+) in the glasses.

  14. Oxygen Fugacity of the Martian Mantle from Pigeonite/Melt Partitioning of Samarium, Europium and Gadolinium

    Science.gov (United States)

    Musselwhite, S.; Jones, J. H.; Shearer, C.

    2004-01-01

    This study is part of an ongoing effort to calibrate the pyroxene/melt Eu oxybarometer for conditions relevant to the martian meteorites. There is fairly good agreement between a determinations using equilibria between Fe-Ti oxides and the estimates from Eu anomalies in shergottite augites in tenns of which meteorites are more or less oxidized. The Eu calibration was for angrite composition pyroxenes which are rather extreme. However, application of a calibration for martian composition augites 113 does not significantly reduce the discrepancy between the two methods. One possible reason for this discrepancy is that augites are non-liquidus. The use of pigeonite rather than augite as the oxy-barometer phase is considered. We have conducted experiments on martian composition pigeonite/melt REE partitioning as a function of fO2.

  15. Folic acid-conjugated europium complexes as luminescent probes for selective targeting of cancer cells.

    Science.gov (United States)

    Quici, Silvio; Casoni, Alessandro; Foschi, Francesca; Armelao, Lidia; Bottaro, Gregorio; Seraglia, Roberta; Bolzati, Cristina; Salvarese, Nicola; Carpanese, Debora; Rosato, Antonio

    2015-02-26

    We report the synthesis of three optical probes (Eu(3+)⊂1, Eu(3+)⊂2, and Eu(3+)⊂3) having a luminescent Eu complex (signaling unit) bonded in different positions to folic acid (FA), the folate receptor (FR) targeting unit. The structures of the two regioisomers Eu(3+)⊂1 and Eu(3+)⊂2 were assigned by mass spectrometric experiments. The optical properties and stability of these probes were assessed in phosphate-buffered saline, cell culture medium, rat serum, and cellular lysate, and results indicated that they are chemically and photophysically stable. Cytotoxicity was studied with ovarian cancer cells having high (SKOV-3), intermediate (OVCAR-3), low (IGROV-1), or null (A2780) expression of FRs. The internalized probe, evaluated in SKOV-3, IGROV-1, and A2780 cells, was in the order Eu(3+)⊂2 > Eu(3+)⊂1 > Eu(3+)⊂3. No internalization was observed for A2780 cells. Such results, together with those obtained in competition experiments of FA versus Eu(3+)⊂2 and FA or Eu(3+)⊂2 versus (3)H-FA, indicate that internalization is receptor-mediated and that Eu(3+)⊂2 shows high selectivity and specificity for FR.

  16. Structural and spectroscopic study of the europium complex with N-(diphenylphosphoryl)pyrazine-2-carboxamide

    Science.gov (United States)

    Pham, Y. H.; Trush, V. A.; Amirkhanov, V. M.; Gawryszewska, P.

    2017-12-01

    This work presents a study of the Eu3+ complex with N-(diphenylphosphoryl)pyrazine-2-carboxamide (HL) and diphenylphosphinate ions (Ph2POO-) as co-ligands with the aim of probing the specific energetic and structural characteristics that influence the ligand-to-metal energy transfer and luminescence efficiency. The compound [Eu2(L)2(μ-Ph2POO)2(κ-OP(O)Ph2)2(CH3OH)2] crystallizes as a dimer with the space group P 1 bar . Absorption and emission (295, 77 K) spectra as well as luminescence decay times were used to characterize the photophysical properties of the complex in the solid state. Very effective energy transfer from ligands to Eu3+ ion was demonstrated.

  17. Ultrafast optically-induced magnetization and conductivity dynamics in the europium chalcogenides

    NARCIS (Netherlands)

    Donker, Michiel

    2014-01-01

    De constante drang naar technologische innovatie en fundamentele kennisvergaring zorgt ervoor dat er over de hele wereld onderzoekers bezig zijn met het ontwikkelen van nieuwe materialen en met de controle van de fysische eigenschappen deze materialen. Buitengewoon interessant zijn de zogenaamde

  18. Pentapotassium europium(III dilithium decafluoride, K5EuLi2F10

    Directory of Open Access Journals (Sweden)

    Anna Gagor

    2009-11-01

    Full Text Available The title compound, K5EuLi2F10, belongs to so-called self-activated materials containing lanthanoid ions within the matrix. A common feature of these systems is a large separation between the closest lanthanoid ions, which is one of the crucial factors governing the self-quenching of luminescence. The crystal structure of K5EuLi2F10 is isotypic with other K5RELi2F10 compounds (RE = Nd, Pr. As expected from the lanthanoid contraction, the unit-cell volume for crystal with Eu3+ ions is the smallest of the three structures. Accordingly, the corresponding interatomic RE—RE distances are shorter. In the structure, distorted EuF8 dodecahedra and two different LiF4 tetrahedra, all with m symmetry, are present, forming sheets parallel to (100. The isolated EuF8 dodecahedra exhibit a mean Eu—F distance of 2.356 Å. The K+ cations are located within and between the sheets, leading to highly irregular KFx polyhedra (x = 8–9 around the alkali metal cations.

  19. Tris[2-(2-pyridyliminomethylphenolato(0.67−]europium(III nitrate

    Directory of Open Access Journals (Sweden)

    Qi-Hua Zhao

    2009-06-01

    Full Text Available The title compound, [Eu(C12H9.33N2O3]NO3, was obtained by the reaction of Eu(NO3·3H2O and the Schiff base ligand 2-(2-pyridyliminomethylphenol. The Eu atom is located on a threefold rotation axis and is nine-coordinated by three tridentate Schiff base ligands in a distorted tricapped trigonal-prismatic geometry. The O atom at the phenol hydroxy group is partially deprotonated and the H atoms are modelled with one-third occupancy according to the space group Roverline{3}. Offset face-to-face π–π [centroid–centroid distance = 3.886 (3 Å] and edge-to-face C—H...π interactions are found between adjacent molecules. An intramolecular O—H...N hydrogen bond is also present.

  20. Europium mass balance in polymict samples and implications for plutonic rocks of the lunar crust

    Science.gov (United States)

    Korotev, Randy L.; Haskin, Larry A.

    1988-01-01

    The mean concentrations of Sm and Eu in the lunar surface crust were analyzed by correlating the Sm concentration and the Sm/Eu ratio with Th concentration obtained from published data on a large number of polymict samples from various locations in the lunar highlands, and using the value of 0.91 microg/g for the mean Th concentration of the highlands surface crust obtained by the orbiting gamma-ray experiments. The mean concentration of Sm in the lunar surface crust was found to be between 2 and 3 microg/g, and that of Eu between 0.7 and 1.2 microg/g. The results indicate that there is no significant enrichment or depletion of Eu, compared to Sm, relative to chondritic abundances; i.e., there is no significant 'Eu anomaly' in average upper crust, contrary to predictions by some earlier investigators.