Salt Efflorescence Effects on Soil Surface Erodibility and Dust Emissions

Science.gov (United States)

Van Pelt, R. S.; Zhang, G.

2017-12-01

Soluble salts resulting from weathering of geological materials often form surface crusts or efflorescences in areas with shallow saline groundwater. In many cases, the affected areas are susceptible to wind erosion due to their lack of protective vegetation and their flat topography. Fugitive dusts containing soluble salts affect the biogeochemistry of deposition regions and may result in respiratory irritation during transport. We created efflorescent crusts on soil trays by surface evaporation of single salt solutions and bombarded the resultant efflorescences with quartz abrader sand in a laboratory wind tunnel. Four replicate trays containing a Torrifluvent soil affected by one of nine salts commonly found in arid and semiarid streams were tested and the emissions were captured by an aspirated multi-stage deposition and filtering system. We found that in most cases the efflorescent crust reduced the soil surface erodibility but also resulted in the emission of salt rich dust. Two of the salts, sodium thiosulfate and calcium chloride, resulted in increased soil volume and erodibility. However, one of the calcium chloride replicates was tested after an outbreak of humid air caused hygroscopic wetting of the soil and it became indurated upon drying greatly decreasing the erodibility. Although saline affected soils are not used for agricultural production and degradation is not a great concern, the release of salt rich dust is an area of environmental concern and steps to control the dust emissions from affected soils should be developed. Future testing will utilize suites of salts found in streams of arid and semiarid regions.

Strength, shrinkage, erodibility and capillary flow characteristics of cement-treated recycled pavement materials

Directory of Open Access Journals (Sweden)

William Fedrigo

2017-09-01

Full Text Available Full-depth recycling with portland cement (FDR-PC has been widely used for pavement rehabilitation; however, doubts remain regarding factors affecting some properties of the recycled material. Aiming on quantifying the effects of those factors on the strength, drying shrinkage, erodibility, capillary rise and absorption of cement-treated mixtures (CTM of reclaimed asphalt pavement (RAP and graded crushed stone, tests were conducted considering different RAP contents, cement contents, compaction efforts and curing times. Cement addition increased the mixtures strength and reduced their erodibility and capillary flow characteristics, but increased shrinkage. Low cement contents resulted in acceptable strength for CTM, but in high capillary rise and absorption, not being suitable if the layer is exposed to long periods of water soaking. Higher compaction effort led to similar effects as cement addition, counterbalancing low cement contents usage and reducing costs and shrinkage cracking risk. Strength and shrinkage showed higher growth rates at early stages, and then precautions should be taken in order to avoid moisture loss. Increasing RAP content decreased strength; though, RAP effect on the other properties was statistically non-significant, indicating a similar behaviour as CTM without RAP. Considering the studied properties, the mixture with most satisfactory behaviour for field applications was identified. The results highlighted strength is not the only property to be considered when designing FDR-PC mixtures; although presenting acceptable strength, some mixtures may fail due to shrinkage cracking or erosion, when exposed to water content variations. Keywords: Full-depth recycling with cement, Strength, Drying shrinkage, Erodibility, Capillary rise, Absorption

Soil erodibility in Europe: a high-resolution dataset based on LUCAS.

Science.gov (United States)

Panagos, Panos; Meusburger, Katrin; Ballabio, Cristiano; Borrelli, Pasqualle; Alewell, Christine

2014-05-01

The greatest obstacle to soil erosion modelling at larger spatial scales is the lack of data on soil characteristics. One key parameter for modelling soil erosion is the soil erodibility, expressed as the K-factor in the widely used soil erosion model, the Universal Soil Loss Equation (USLE) and its revised version (RUSLE). The K-factor, which expresses the susceptibility of a soil to erode, is related to soil properties such as organic matter content, soil texture, soil structure and permeability. With the Land Use/Cover Area frame Survey (LUCAS) soil survey in 2009 a pan-European soil dataset is available for the first time, consisting of around 20,000 points across 25 Member States of the European Union. The aim of this study is the generation of a harmonised high-resolution soil erodibility map (with a grid cell size of 500 m) for the 25 EU Member States. Soil erodibility was calculated for the LUCAS survey points using the nomograph of Wischmeier and Smith (1978). A Cubist regression model was applied to correlate spatial data such as latitude, longitude, remotely sensed and terrain features in order to develop a high-resolution soil erodibility map. The mean K-factor for Europe was estimated at 0.032 thahha(-1)MJ(-1)mm(-1) with a standard deviation of 0.009 thahha(-1)MJ(-1)mm(-1). The yielded soil erodibility dataset compared well with the published local and regional soil erodibility data. However, the incorporation of the protective effect of surface stone cover, which is usually not considered for the soil erodibility calculations, resulted in an average 15% decrease of the K-factor. The exclusion of this effect in K-factor calculations is likely to result in an overestimation of soil erosion, particularly for the Mediterranean countries, where highest percentages of surface stone cover were observed. Copyright © 2014. Published by Elsevier B.V.

Soil erodibility mapping using three approaches in the Tangiers province –Northern Morocco

Directory of Open Access Journals (Sweden)

Hamza Iaaich

2016-09-01

Full Text Available Soil erodibility is a key factor in assessing soil loss rates. In fact, soil loss is the most occurring land degradation form in Morocco, affecting rural and urban vulnerable areas. This work deals with large scale mapping of soil erodibility using three mapping approaches: (i the CORINE approach developed for Europe by the JRC; (ii the UNEP/FAO approach developed within the frame of the United Nations Environmental Program for the Mediterranean area; (iii the Universal Soil Loss Equation (USLE K factor. Our study zone is the province of Tangiers, North-West of Morocco. For each approach, we mapped and analyzed different erodibility factors in terms of parent material, topography and soil attributes. The thematic maps were then integrated using a Geographic Information System to elaborate a soil erodibility map for each of the three approaches. Finally, the validity of each approach was checked in the field, focusing on highly eroded areas, by confronting the estimated soil erodibility and the erosion state as observed in the field. We used three statistical indicators for validation: overall accuracy, weighted Kappa factor and omission/commission errors. We found that the UNEP/FAO approach, based principally on lithofacies and topography as mapping inputs, is the most adapted for the case of our study zone, followed by the CORINE approach. The USLE K factor underestimated the soil erodibility, especially for highly eroded areas.

Power module assembly with reduced inductance

Energy Technology Data Exchange (ETDEWEB)

Ward, Terence G.; Stancu, Constantin C.; Jaksic, Marko; Mann, Brooks S.

2018-03-13

A power module assembly has a plurality of electrically conducting layers, including a first layer and a third layer. One or more electrically insulating layers are operatively connected to each of the plurality of electrically conducting layers. The electrically insulating layers include a second layer positioned between and configured to electrically isolate the first and the third layers. The first layer is configured to carry a first current flowing in a first direction. The third layer is configured to carry a second current flowing in a second direction opposite to the first direction, thereby reducing an inductance of the assembly. The electrically insulating layers may include a fourth layer positioned between and configured to electrically isolate the third layer and a fifth layer. The assembly results in a combined substrate and heat sink structure. The assembly eliminates the requirements for connections between separate substrate and heat sink structures.

Societal Forces That ERODE Creativity

Science.gov (United States)

Sternberg, Robert; Kaufman, James C.

2018-01-01

Background/Context: Creativity is an indispensable force in intellectual, social, cultural, and economic development. Yet societal forces conspire to erode it. Educators have despaired for many years over how schools often fail to encourage creativity, but society as a whole is just as guilty. But how do schools and society fail to encourage, or…

Value-Eroding Teacher Behaviors Scale: A Validity and Reliability Study

Science.gov (United States)

Arseven, Zeynep; Kiliç, Abdurrahman; Sahin, Seyma

2016-01-01

In the present study, it is aimed to develop a valid and reliable scale for determining value-eroding behaviors of teachers, hence their values of judgment. The items of the "Value-eroding Teacher Behaviors Scale" were designed in the form of 5-point likert type rating scale. The exploratory factor analysis (EFA) was conducted to…

7 CFR 12.21 - Identification of highly erodible lands criteria.

Science.gov (United States)

2010-01-01

... the Universal Soil Loss Equation (USLE): (i) Rainfall and runoff (R); (ii) The degree to which the... and surface soil moisture (C) and the degree to which soil resists wind erosion (I). (3) The USLE is...) Basis for identification as highly erodible. Soil map units and an erodibility index will be used as the...

Dispersive and erodible soils - fundamental differences

CSIR Research Space (South Africa)

Paige-Green, P

2008-11-01

Full Text Available Dispersive, erodible and slaking soils are prevalent over wide areas of South Africa. Each of these materials increases the cost of construction, but dispersive soils are likely to lead to far more serious problems, particularly in dam construction...

The use of nutritional supplements to induce ketosis and reduce symptoms associated with keto-induction: a narrative review

OpenAIRE

Cliff J. d C. Harvey; Grant M. Schofield; Micalla Williden

2018-01-01

Background Adaptation to a ketogenic diet (keto-induction) can cause unpleasant symptoms, and this can reduce tolerability of the diet. Several methods have been suggested as useful for encouraging entry into nutritional ketosis (NK) and reducing symptoms of keto-induction. This paper reviews the scientific literature on the effects of these methods on time-to-NK and on symptoms during the keto-induction phase. Methods PubMed, Science Direct, CINAHL, MEDLINE, Alt Health Watch, Food Science So...

Bonding stability of adhesive systems to eroded dentin

Directory of Open Access Journals (Sweden)

Janaina Barros CRUZ

2015-01-01

Full Text Available This in vitro study evaluated the immediate and 6 months microshear bond strength (µSBS of different adhesive systems to sound and eroded dentin. Sixty bovine incisors were embedded in acrylic resin and ground to obtain flat buccal dentin surfaces. Specimens were randomly allocated into two groups: sound dentin (immersion in artificial saliva and eroded dentin (erosive challenge following a pH cycling model comprising 4 ×/day Sprite Light® drink for 10 days. Then, specimens were reassigned according to the adhesive system: etch-and-rinse adhesive (Adper Single Bond, two-step self-etch system (Clearfil SE Bond, or one-step self-etch adhesive (Adper Easy One. Polyethylene tubes with an internal diameter of 0.76 mm were placed over pre-treated dentin and filled with resin composite (Z250. Half of the specimens were evaluated by the µSBS test after 24 h, and the other half 6 months later, after water storage at 37°C. Failure mode was evaluated using a stereomicroscope (400×. Data were analyzed by three-way repeated measures analysis of variance and Tukey’s post hoc tests (α = 0.05. After 6 months of water aging, marked reductions in µSBS values were observed, irrespective of the substrate. The µSBS values for eroded dentin were lower than those obtained for sound dentin. No difference in bonding effectiveness was observed among adhesive systems. For all groups, adhesive/mixed failure was observed. In conclusion, eroded dentin compromises the bonding quality of adhesive systems over time.

An iso-erodent map Imo state of Nigeria | Madubuike | International ...

African Journals Online (AJOL)

Among inputs/resources often needed for erosion risk assessment of a region is the iso-erodent map of the region. This is a map showing areas of equal erosion potentials in the region. As Imo and Abia states of Nigeria lie in a high erosion region of the country, it was decided in this work to produce an iso-erodent map of ...

U.S.V.I. Soil Erodibility (Kffact)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — U.S.V.I. soil erodibility (Kffactor) - low values indicate low vulnerability to erosion, higher values mean higher susceptibility to runoff.

Elastic wave generated by granular impact on rough and erodible surfaces

Science.gov (United States)

Bachelet, Vincent; Mangeney, Anne; de Rosny, Julien; Toussaint, Renaud; Farin, Maxime

2018-01-01

The elastic waves generated by impactors hitting rough and erodible surfaces are studied. For this purpose, beads of variable materials, diameters, and velocities are dropped on (i) a smooth PMMA plate, (ii) stuck glass beads on the PMMA plate to create roughness, and (iii) the rough plate covered with layers of free particles to investigate erodible beds. The Hertz model validity to describe impacts on a smooth surface is confirmed. For rough and erodible surfaces, an empirical scaling law that relates the elastic energy to the radius Rb and normal velocity Vz of the impactor is deduced from experimental data. In addition, the radiated elastic energy is found to decrease exponentially with respect to the bed thickness. Lastly, we show that the variability of the elastic energy among shocks increases from some percents to 70% between smooth and erodible surfaces. This work is a first step to better quantify seismic emissions of rock impacts in natural environment, in particular on unconsolidated soils.

Testing the ecotoxicology of vegetable versus mineral based lubricating oils: 2. Induction of mixed function oxidase enzymes in barramundi, Lates calcarifer, a tropical fish species

International Nuclear Information System (INIS)

Mercurio, Philip; Burns, Kathryn A.; Cavanagh, Joanne

2004-01-01

An increasing number of vegetable-based oils are being developed as environmentally friendly alternatives to petroleum products. However, toxicity towards key tropical marine species has not been investigated. In this study we used laboratory-based biomarker induction experiments to compare the relative stress of a vegetable-based lubricating oil for marine 2-stroke engines with its mineral oil-based counterpart on tropical fish. The sub-lethal stress of 2-stoke outboard lubricating oils towards the fish Lates calcarifer (barramundi) was examined using liver microsomal mixed function oxidase (MFO) induction assays. This study is the first investigation into the use of this key commercial species in tropical North Queensland, Australia in stress assessment of potential hydrocarbon pollution using ethoxyresorufin O-deethylase (EROD) induction. Our results indicated that barramundi provide a wide range of inducible rates of EROD activity in response to relevant organic stressors. The vegetable- and mineral-based lubricants induced significant EROD activity at 1.0 mg kg -1 and there was no significant difference between the two oil treatments at that concentration. At increasing concentrations of 2 and 3 mg kg -1 , the mineral-based lubricant resulted in slightly higher EROD activity than the vegetable-based lubricant. The EROD activity of control and treated barramundi are found to be within ranges for other species from temperate and tropical environments. These results indicate that vegetable-based lubricants may be less stressful to barramundi than their mineral counterparts at concentrations of lubricant ≥2 mg kg -1 . There is great potential for this species to be used in the biomonitoring of waterways around tropical North Queensland and SE Asia. - Vegetable-based lubricating oils appear to cause a tropical fish species less stress than mineral oils

Testing the ecotoxicology of vegetable versus mineral based lubricating oils: 2. Induction of mixed function oxidase enzymes in barramundi, Lates calcarifer, a tropical fish species

Energy Technology Data Exchange (ETDEWEB)

Mercurio, Philip; Burns, Kathryn A.; Cavanagh, Joanne

2004-05-01

An increasing number of vegetable-based oils are being developed as environmentally friendly alternatives to petroleum products. However, toxicity towards key tropical marine species has not been investigated. In this study we used laboratory-based biomarker induction experiments to compare the relative stress of a vegetable-based lubricating oil for marine 2-stroke engines with its mineral oil-based counterpart on tropical fish. The sub-lethal stress of 2-stoke outboard lubricating oils towards the fish Lates calcarifer (barramundi) was examined using liver microsomal mixed function oxidase (MFO) induction assays. This study is the first investigation into the use of this key commercial species in tropical North Queensland, Australia in stress assessment of potential hydrocarbon pollution using ethoxyresorufin O-deethylase (EROD) induction. Our results indicated that barramundi provide a wide range of inducible rates of EROD activity in response to relevant organic stressors. The vegetable- and mineral-based lubricants induced significant EROD activity at 1.0 mg kg{sup -1} and there was no significant difference between the two oil treatments at that concentration. At increasing concentrations of 2 and 3 mg kg{sup -1}, the mineral-based lubricant resulted in slightly higher EROD activity than the vegetable-based lubricant. The EROD activity of control and treated barramundi are found to be within ranges for other species from temperate and tropical environments. These results indicate that vegetable-based lubricants may be less stressful to barramundi than their mineral counterparts at concentrations of lubricant {>=}2 mg kg{sup -1}. There is great potential for this species to be used in the biomonitoring of waterways around tropical North Queensland and SE Asia. - Vegetable-based lubricating oils appear to cause a tropical fish species less stress than mineral oils.

Robotic removal of eroded vaginal mesh into the bladder.

Science.gov (United States)

Macedo, Francisco Igor B; O'Connor, Jeffrey; Mittal, Vijay K; Hurley, Patrick

2013-11-01

Vaginal mesh erosion into the bladder after midurethral sling procedure or cystocele repair is uncommon, with only a few cases having been reported in the literature. The ideal surgical management is still controversial. Current options for removal of eroded mesh include: endoscopic, transvaginal or abdominal (either open or laparoscopic) approaches. We, herein, present the first case of robotic removal of a large eroded vaginal mesh into the bladder and discuss potential benefits and limitations of the technique. © 2013 The Japanese Urological Association.

The use of nutritional supplements to induce ketosis and reduce symptoms associated with keto-induction: a narrative review.

Science.gov (United States)

Harvey, Cliff J D C; Schofield, Grant M; Williden, Micalla

2018-01-01

Adaptation to a ketogenic diet (keto-induction) can cause unpleasant symptoms, and this can reduce tolerability of the diet. Several methods have been suggested as useful for encouraging entry into nutritional ketosis (NK) and reducing symptoms of keto-induction. This paper reviews the scientific literature on the effects of these methods on time-to-NK and on symptoms during the keto-induction phase. PubMed, Science Direct, CINAHL, MEDLINE, Alt Health Watch, Food Science Source and EBSCO Psychology and Behavioural Sciences Collection electronic databases were searched online. Various purported ketogenic supplements were searched along with the terms "ketogenic diet", "ketogenic", "ketosis" and ketonaemia (/ ketonemia). Additionally, author names and reference lists were used for further search of the selected papers for related references. Evidence, from one mouse study, suggests that leucine doesn't significantly increase beta-hydroxybutyrate (BOHB) but the addition of leucine to a ketogenic diet in humans, while increasing the protein-to-fat ratio of the diet, doesn't reduce ketosis. Animal studies indicate that the short chain fatty acids acetic acid and butyric acid, increase ketone body concentrations. However, only one study has been performed in humans. This demonstrated that butyric acid is more ketogenic than either leucine or an 8-chain monoglyceride. Medium-chain triglycerides (MCTs) increase BOHB in a linear, dose-dependent manner, and promote both ketonaemia and ketogenesis. Exogenous ketones promote ketonaemia but may inhibit ketogenesis. There is a clear ketogenic effect of supplemental MCTs; however, it is unclear whether they independently improve time to NK and reduce symptoms of keto-induction. There is limited research on the potential for other supplements to improve time to NK and reduce symptoms of keto-induction. Few studies have specifically evaluated symptoms and adverse effects of a ketogenic diet during the induction phase. Those that

[Spatiotemporal variation of typical red soil eroded landscape pattern: a case study in Changting County of Fujian Province].

Science.gov (United States)

Wu, Guo-sheng; Lin, Hui-hua; Zhu, He-jian; Sha, Jin-ming; Dai, Wen-yuan

2011-07-01

Based on the 1988, 2000, and 2007 remote sensing images of a typical red soil eroded region (Changting County, Fujian Province) and the digital elevation model (DEM), the eroded landscape types were worked out, and the changes of the eroded landscape pattern in the region from 1988 to 2007 were analyzed with the spatial mathematics model. In 1988-2007, different eroded landscape types in the region had the characteristics of inter-transfer, mainly manifested in the transfer from seriously eroded to lightly eroded types but still existed small amount of the transference from lightly eroded to seriously eroded types. Little change was observed in the controid of the eroded landscape. In the County, Hetian Town was all along the eroded center. During the study period, the landscape pattern index showed a tendency of low heterogeneity, low fragmentation, and high regularization at landscape level, but an overall improvement and expansion of lightly eroded and easy-to-tackle patches as well as the partial improvement and fragmentation of seriously eroded and difficult-to-tackle patches at patch level.

Textural characteristics and sedimentary environment of sediment at eroded and deposited regions in the severely eroded coastline of Batu Pahat, Malaysia.

Science.gov (United States)

Wan Mohtar, Wan Hanna Melini; Nawang, Siti Aminah Bassa; Abdul Maulud, Khairul Nizam; Benson, Yannie Anak; Azhary, Wan Ahmad Hafiz Wan Mohamed

2017-11-15

This study investigates the textural characteristics of sediments collected at eroded and deposited areas of highly severed eroded coastline of Batu Pahat, Malaysia. Samples were taken from systematically selected 23 locations along the 67km stretch of coastline and are extended to the fluvial sediments of the main river of Batu Pahat. Grain size distribution analysis was conducted to identify its textural characteristics and associated sedimentary transport behaviours. Sediments obtained along the coastline were fine-grained material with averaged mean size of 7.25 ϕ, poorly sorted, positively skewed and has wide distributions. Samples from eroded and deposition regions displayed no distinctive characteristics and exhibited similar profiles. The high energy condition transported the sediments as suspension, mostly as pelagic and the sediments were deposited as shallow marine and agitated deposits. The fluvial sediments of up to 3km into the river have particularly similar profile of textural characteristics with the neighbouring marine sediments from the river mouth. Profiles were similar with marine sediments about 3km opposite the main current and can go up to 10km along the current of Malacca Straits. Copyright © 2017 Elsevier B.V. All rights reserved.

A Physically—Based Geometry Model for Transport Distance Estimation of Rainfall-Eroded Soil Sediment

Directory of Open Access Journals (Sweden)

Qian-Gui Zhang

2016-01-01

Full Text Available Estimations of rainfall-induced soil erosion are mostly derived from the weight of sediment measured in natural runoff. The transport distance of eroded soil is important for evaluating landscape evolution but is difficult to estimate, mainly because it cannot be linked directly to the eroded sediment weight. The volume of eroded soil is easier to calculate visually using popular imaging tools, which can aid in estimating the transport distance of eroded soil through geometry relationships. In this study, we present a straightforward geometry model to predict the maximum sediment transport distance incurred by rainfall events of various intensity and duration. In order to verify our geometry prediction model, a series of experiments are reported in the form of a sediment volume. The results show that cumulative rainfall has a linear relationship with the total volume of eroded soil. The geometry model can accurately estimate the maximum transport distance of eroded soil by cumulative rainfall, with a low root-mean-square error (4.7–4.8 and a strong linear correlation (0.74–0.86.

Outcome of Membrane Sweeping in Reducing Induction Rates in Post-Date Pregnancies

International Nuclear Information System (INIS)

Saleem, U.; Mustafa, N.; Akhtar, S.

2013-01-01

Objectives: To determine the effectiveness of membrane sweeping in reducing need for induction of labour in post-date pregnancies and to enlist types and frequencies of complications experienced with membrane sweeping. Study Design: Randomized Control trial. Setting and Duration of Study: The study was carried out at Department of Obstetrics and Gynaecology, Combined Military Hospital, Lahore from February 2007 to April 2008. Patients and Methods: One hundred primi or second gravidas with uncomplicated singleton pregnancies having cephalic presentation at 40+1-5 weeks of gestation were enrolled after informed consent, and divided randomly into two groups of fifty each. Biophysical profile of 8/8 for each case was ensured. Group A underwent membrane sweeping while group B did not. All patients not having spontaneous labour were induced at 40+5 weeks. Data regarding number of patients having spontaneous labour or induction of labour was recorded. Mode of delivery either vaginal or cesarean birth was also recorded. In group A occurence of complications i.e vaginal bleeding or leaking, discomfort, irregular pains, fever and neonatal sepsis was recorded. Results: The difference in rate of spontaneous labor, induction rate and mode of delivery was insignificant between both the groups (p>0.05). In group A, 44% felt discomfort, 4% had bleeding per vaginum, 2% had leaking per vaginum and 28% had more than one complication. There were no cases of maternal or neonatal sepsis. Twenty percent did not have any side effects. Conclusion: Sweeping of membranes is not effective in reducing induction rates in post dates pregnancies. It does not improve the spontaneous labour rate and there is no effect on the mode of delivery. Therefore, any potential benefits of this intervention must be balanced against risk of maternal discomfort and other adverse effects. (author)

The use of nutritional supplements to induce ketosis and reduce symptoms associated with keto-induction: a narrative review

Directory of Open Access Journals (Sweden)

Cliff J. d C. Harvey

2018-03-01

Full Text Available Background Adaptation to a ketogenic diet (keto-induction can cause unpleasant symptoms, and this can reduce tolerability of the diet. Several methods have been suggested as useful for encouraging entry into nutritional ketosis (NK and reducing symptoms of keto-induction. This paper reviews the scientific literature on the effects of these methods on time-to-NK and on symptoms during the keto-induction phase. Methods PubMed, Science Direct, CINAHL, MEDLINE, Alt Health Watch, Food Science Source and EBSCO Psychology and Behavioural Sciences Collection electronic databases were searched online. Various purported ketogenic supplements were searched along with the terms “ketogenic diet”, “ketogenic”, “ketosis” and ketonaemia (/ ketonemia. Additionally, author names and reference lists were used for further search of the selected papers for related references. Results Evidence, from one mouse study, suggests that leucine doesn’t significantly increase beta-hydroxybutyrate (BOHB but the addition of leucine to a ketogenic diet in humans, while increasing the protein-to-fat ratio of the diet, doesn’t reduce ketosis. Animal studies indicate that the short chain fatty acids acetic acid and butyric acid, increase ketone body concentrations. However, only one study has been performed in humans. This demonstrated that butyric acid is more ketogenic than either leucine or an 8-chain monoglyceride. Medium-chain triglycerides (MCTs increase BOHB in a linear, dose-dependent manner, and promote both ketonaemia and ketogenesis. Exogenous ketones promote ketonaemia but may inhibit ketogenesis. Conclusions There is a clear ketogenic effect of supplemental MCTs; however, it is unclear whether they independently improve time to NK and reduce symptoms of keto-induction. There is limited research on the potential for other supplements to improve time to NK and reduce symptoms of keto-induction. Few studies have specifically evaluated symptoms and adverse

Advancing Understanding of Earthquakes by Drilling an Eroding Convergent Margin

Science.gov (United States)

von Huene, R.; Vannucchi, P.; Ranero, C. R.

2010-12-01

A program of IODP with great societal relevance is sampling and instrumenting the seismogenic zone. The zone generates great earthquakes that trigger tsunamis, and submarine slides thereby endangering coastal communities containing over sixty percent of the earth’s population. To asses and mitigate this endangerment it is urgent to advance understanding of fault dynamics that allows more timely anticipation of hazardous seismicity. Seismogenesis on accreting and eroding convergent plate boundaries apparently differ because of dissimilar materials along the interplate fault. As the history of instrumentally recorded earthquakes expands the difference becomes clearer. The more homogeneous clay, silt and sand subducted at accreting margins is associated with great earthquakes (M 9) whereas the fragmented upper plate rock that can dominate subducted material along an eroding margin plate interface is associated with many tsunamigenic earthquakes (Bilek, 2010). Few areas have been identified where the seismogenic zone can be reached with scientific drilling. In IODP accreting margins are studied on the NanTroSeize drill transect off Japan where the ultimate drilling of the seismogenic interface may occur by the end of IODP. The eroding Costa Rica margin will be studied in CRISP where a drill program will begin in 2011. The Costa Rican geophysical site survey will be complete with acquisition and processing of 3D seismic data in 2011 but the entire drilling will not be accomplished in IODP. It is appropriate that the accreting margin study be accomplished soon considering the indications of a pending great earthquake that will affect a country that has devoted enormous resources to IODP. However, understanding the erosional end-member is scientifically as important to an understanding of fault mechanics. Transoceanic tsunamis affect the entire Pacific rim where most subduction zones are eroding margins. The Costa Rican subduction zone is less complex operationally and

Erodibility of waste (Loess) soils from construction sites under water and wind erosional forces.

Science.gov (United States)

Tanner, Smadar; Katra, Itzhak; Argaman, Eli; Ben-Hur, Meni

2018-03-01

Excess soils from construction sites (waste soils) become a problem when exposed to soil erosion by water or wind. Understanding waste soil erodibility can contribute to its proper reuse for various surface applications. The general objective of the study was to provide a better understanding of the effects of soil properties on erodibility of waste soils excavated from various depths in a semiarid region under rainfall and wind erosive forces. Soil samples excavated from the topsoil (0-0.3m) and subsoil layers (0.3-0.9 and >1m depths) were subjected to simulated rainfall and wind. Under rainfall erosive forces, the subsoils were more erodible than the topsoil, in contrast to the results obtained under wind erosive forces. Exchangeable sodium percentage was the main factor controlling soil erodibility (K i ) under rainfall, and a significant logarithmic regression line was found between these two parameters. In addition, a significant, linear regression was found between K i and slaking values for the studied soil samples, suggesting that the former can be predicted from the latter. Soil erodibility under wind erosion force was controlled mainly by the dry aggregate characteristics (mean weight diameter and aggregate density): their higher values in the subsoil layers resulted in lower soil erodibility compared to the topsoil. Copyright © 2017 Elsevier B.V. All rights reserved.

Wind erodibility of soils from North Darfur State

International Nuclear Information System (INIS)

Medani, G. H.; Mustafa, M. A.

2003-01-01

Wind erodibility of soils (WE) is a prime factor for the prediction, assessment and mapping of wind erosion. Hence, this study was undertaken to generate WE data and pertinent relationships for North Darfur State. Surface soil samples (0-3 cm) were collected from forty farms scattered all over the state. Non-erodible soil particles (NEP) (>0.84 mm in diameter), WE and various relevant physical and chemical soil properties were determined. Regression analysis showed that NEP significantly (p 2 =0.825), clay (r 2 =0.754), silt (r 2 =0.737) and clay/ (silt + sand) ratio (r 2 =0.663), and decreased with increase in sand (r 2 =0.761), (silt+sand) / clay ratio (r 2 =0.766) and (silt+sand) / (clay+organic matter) ratio (r 2 =0.811). The four basic soil properties and their ratios gave the reverse effects on WE with slightly lower coefficients of determinations. Although organic matter is a slightly better predictor of both NEP and WE than (Si+S)/ (C+OM) ratio, the latter is preferred because it integrates in addition to OM resilient soil properties. A multiple regression equation with a relatively high coefficient of determination (R 2 =0.830) may also be used for predicting NEP from knowledge of the four prime soil properties. These properties accounted for only 62% of the variation of WE, thus it is not recommended for prediction purposes. The determined wind erodibility groups correlated very well with those established else where.(Author)

Dose-response curves for fish MFO induction: How do we interpret different maxima and slopes?

International Nuclear Information System (INIS)

Parrott, J.L.

1995-01-01

Induction of hepatic mixed function oxygenase (MFO) activity has been useful for screening effluents from pulp mills and oil refineries. Effluents and pure compounds can be assessed by direct fish exposure or by concentration with semipermeable membrane devices (SPMDs) and by measuring MFO in fish liver cell lines exposed to SPMD extracts. In these experiments, both fish and fish cells showed differences in slopes of dose-response curves, and in the maximal ethoxyresorufin-O-deethylase (EROD) activity. For example, TCDD elicits an EROD maxima of over 500 pmol/mg/min in PLHC-1 (Poeciliopsis lucida hepatocellular carcinoma cell line), while pulp mill and oil refinery effluent extracts showed maxima of 40 to 200 pmol/mg/min. Substituted phenanthrenes caused induction maxima of 100 pmol/mg/min. Similarly, in rainbow trout in vivo, TCDD and other chlorinated dioxins and furans induced up to 500 pmol/mg/min, whereas pulp mill and refinery effluents and substituted phenanthrenes produced EROD maxima of up to 100 pmol/mg/min. Differences in the slopes of dose-response curves were also common. In the current assessment of potencies, these diverse response curves are boiled-down to one number, the EC50 or other threshold-type of concentration. Comparisons of EC50s cannot express these differences and instead, ignore them. However, the authors realize there must be a better approach that takes into account these large differences in dose-response curve shape, slope and maxima. Interaction and discussions with modelers in the session will allow them to discuss various approaches to expressing the potencies of MFO inducers in fish

The immediate effectiveness of barley straw mulch in reducing soil erodibility and surface runoff generation in Mediterranean vineyards.

Science.gov (United States)

Prosdocimi, Massimo; Jordán, Antonio; Tarolli, Paolo; Keesstra, Saskia; Novara, Agata; Cerdà, Artemi

2016-03-15

Soil and water loss in agriculture is a major problem throughout the world, and especially in Mediterranean areas. Non-conservation agricultural practices have further aggravated the situation, especially in vineyards, which are affected by one of the highest rates of soil loss among cultivated lands. Therefore, it is necessary to find the right soil practices for more sustainable viticulture. In this regard, straw mulching has proven to be effective in other crop and fire affected soils, but, nonetheless, little research has been carried out in vineyards. This research tests the effect of barley straw mulching on soil erosion and surface runoff on vineyards in Eastern Spain where the soil and water losses are non-sustainable. An experiment was setup using rainfall simulation tests at 55 mm h(-1) over 1h on forty paired plots of 0.24 m(2): twenty bare and twenty straw covered. Straw cover varied from 48 to 90% with a median value of 59% as a result of the application of 75 g of straw per m(2). The use of straw mulch resulted in delayed ponding and runoff generation and, as a consequence, the median water loss decreased from 52.59 to 39.27% of the total rainfall. The straw cover reduced the median sediment concentration in runoff from 9.8 to 3.0 g L(-1) and the median total sediment detached from 70.34 to 15.62 g per experiment. The median soil erosion rate decreased from 2.81 to 0.63 Mg ha(-1)h(-1) due to the straw mulch protection. Straw mulch is very effective in reducing soil erodibility and surface runoff, and this benefit was achieved immediately after the application of the straw. Copyright © 2015 Elsevier B.V. All rights reserved.

Biorock Electric Reefs Grow Back Severely Eroded Beaches in Months

Directory of Open Access Journals (Sweden)

Thomas J. F. Goreau

2017-10-01

Full Text Available Severely eroded beaches on low lying islands in Indonesia were grown back in a few months—believed to be a record—using an innovative method of shore protection, Biorock electric reef technology. Biorock shore protection reefs are growing limestone structures that get stronger with age and repair themselves, are cheaper than concrete or rock sea walls and breakwaters, and are much more effective at shore protection and beach growth. Biorock reefs are permeable, porous, growing, self-repairing structures of any size or shape, which dissipate wave energy by internal refraction, diffraction, and frictional dissipation. They do not cause reflection of waves like hard sea walls and breakwaters, which erodes the sand in front of, and then underneath, such structures, until they collapse. Biorock reefs stimulate settlement, growth, survival, and resistance to the environmental stress of all forms of marine life, restoring coral reefs, sea grasses, biological sand production, and fisheries habitat. Biorock reefs can grow back eroded beaches and islands faster than the rate of sea level rise, and are the most cost-effective method of shore protection and adaptation to global sea level rise for low lying islands and coasts.

Cytochrome P4501A induction in avian hepatocyte cultures exposed to polychlorinated biphenyls: Comparisons with AHR1-mediated reporter gene activity and in ovo toxicity

Energy Technology Data Exchange (ETDEWEB)

Manning, Gillian E., E-mail: gmann017@uottawa.ca [Centre for Advanced Research in Environmental Genomics, Department of Biology, University of Ottawa, Ottawa, ON, Canada K1N 6N5 (Canada); Environment Canada, National Wildlife Research Centre, Ottawa, ON, Canada K1A 0H3 (Canada); Mundy, Lukas J., E-mail: lukas.mundy@ec.gc.ca [Centre for Advanced Research in Environmental Genomics, Department of Biology, University of Ottawa, Ottawa, ON, Canada K1N 6N5 (Canada); Environment Canada, National Wildlife Research Centre, Ottawa, ON, Canada K1A 0H3 (Canada); Crump, Doug, E-mail: doug.crump@ec.gc.ca [Environment Canada, National Wildlife Research Centre, Ottawa, ON, Canada K1A 0H3 (Canada); Jones, Stephanie P., E-mail: stephanie.jones@ec.gc.ca [Environment Canada, National Wildlife Research Centre, Ottawa, ON, Canada K1A 0H3 (Canada); Chiu, Suzanne, E-mail: suzanne.chiu@ec.gc.ca [Environment Canada, National Wildlife Research Centre, Ottawa, ON, Canada K1A 0H3 (Canada); Klein, Jeff, E-mail: jeffery@well-labs.com [Wellington Laboratories Inc., Research Division, Guelph, ON, Canada N1G 3chsM5 (Canada); Konstantinov, Alex, E-mail: alex@well-labs.com [Wellington Laboratories Inc., Research Division, Guelph, ON, Canada N1G 3chsM5 (Canada); Potter, Dave, E-mail: dpotter@well-labs.com [Wellington Laboratories Inc., Research Division, Guelph, ON, Canada N1G 3chsM5 (Canada); Kennedy, Sean W., E-mail: sean.kennedy@ec.gc.ca [Centre for Advanced Research in Environmental Genomics, Department of Biology, University of Ottawa, Ottawa, ON, Canada K1N 6N5 (Canada); Environment Canada, National Wildlife Research Centre, Ottawa, ON, Canada K1A 0H3 (Canada)

2013-01-01

Avian-specific toxic equivalency factors (TEFs) were developed by the World Health Organization to simplify environmental risk assessments of dioxin-like compounds (DLCs), but TEFs do not account for differences in the toxic and biochemical potencies of DLCs among species of birds. Such variability may be due to differences in species sensitivity to individual DLCs. The sensitivity of avian species to DLCs was recently associated with the identity of amino acids 324 and 380 in the aryl hydrocarbon receptor 1 (AHR1) ligand binding domain. A luciferase reporter gene (LRG) assay, measuring AHR1-mediated induction of a cytochrome P450 1A5 (CYP1A5) reporter gene, in combination with a species' AHR1 ligand binding domain sequence, were also shown to predict avian species sensitivity to polychlorinated biphenyls (PCBs) and PCB relative potency in a given species. The goals of the present study were to (1) characterize the concentration-dependent effects of 2,3,7,8-tetrachlorodibenzo-p-dioxin and PCBs 126, 77, 105 and 118 on induction of ethoxyresorufin O-deethylase (EROD) activity and CYP1A4/5 mRNA in chicken, ring-necked pheasant and Japanese quail embryo hepatocytes and (2) compare these in vitro results to those previously generated by the LRG assay and in ovo toxicity studies. EROD activity and CYP1A4/5 mRNA expression data support and complement the findings of the LRG assay. CYP1A enzyme activity and mRNA expression were significantly correlated both with luciferase activity and in ovo toxicity induced by PCBs. Relative potency values were generally similar between the LRG and EROD assays and indicate that the relative potency of some PCBs may differ among species. -- Highlights: ► The chicken isn't the most sensitive species to CYP1A induction by PCB 105 and 118. ► The relative potency of PCBs differs between avian species. ► EROD activity was correlated with luciferase activity from the LRG assay. ► EROD activity was a better predictor of

Cytochrome P4501A induction in avian hepatocyte cultures exposed to polychlorinated biphenyls: Comparisons with AHR1-mediated reporter gene activity and in ovo toxicity

International Nuclear Information System (INIS)

Manning, Gillian E.; Mundy, Lukas J.; Crump, Doug; Jones, Stephanie P.; Chiu, Suzanne; Klein, Jeff; Konstantinov, Alex; Potter, Dave; Kennedy, Sean W.

2013-01-01

Avian-specific toxic equivalency factors (TEFs) were developed by the World Health Organization to simplify environmental risk assessments of dioxin-like compounds (DLCs), but TEFs do not account for differences in the toxic and biochemical potencies of DLCs among species of birds. Such variability may be due to differences in species sensitivity to individual DLCs. The sensitivity of avian species to DLCs was recently associated with the identity of amino acids 324 and 380 in the aryl hydrocarbon receptor 1 (AHR1) ligand binding domain. A luciferase reporter gene (LRG) assay, measuring AHR1-mediated induction of a cytochrome P450 1A5 (CYP1A5) reporter gene, in combination with a species' AHR1 ligand binding domain sequence, were also shown to predict avian species sensitivity to polychlorinated biphenyls (PCBs) and PCB relative potency in a given species. The goals of the present study were to (1) characterize the concentration-dependent effects of 2,3,7,8-tetrachlorodibenzo-p-dioxin and PCBs 126, 77, 105 and 118 on induction of ethoxyresorufin O-deethylase (EROD) activity and CYP1A4/5 mRNA in chicken, ring-necked pheasant and Japanese quail embryo hepatocytes and (2) compare these in vitro results to those previously generated by the LRG assay and in ovo toxicity studies. EROD activity and CYP1A4/5 mRNA expression data support and complement the findings of the LRG assay. CYP1A enzyme activity and mRNA expression were significantly correlated both with luciferase activity and in ovo toxicity induced by PCBs. Relative potency values were generally similar between the LRG and EROD assays and indicate that the relative potency of some PCBs may differ among species. -- Highlights: ► The chicken isn't the most sensitive species to CYP1A induction by PCB 105 and 118. ► The relative potency of PCBs differs between avian species. ► EROD activity was correlated with luciferase activity from the LRG assay. ► EROD activity was a better predictor of toxicity than CYP

Frijolito Watershed: Integrated investigations of a rapidly eroding pinyon-juniper hillslope

International Nuclear Information System (INIS)

Wilcox, B.P.; Pitlick, J.

1995-01-01

The dramatic acceleration of erosion associated with the expansion of pinyon-juniper woodlands over the past 100 years has been widely recognized, but few process-based studies of this phenomenon have been undertaken. In an attempt to identify the underlying causes, and the factors that affect erosion processes, we have initiated an interdisciplinary study of a rapidly eroding pinyon-juniper woodland in northern New Mexico. Since July 1993, we have collected data on runoff, erosion, and weather conditions from a 1-ha catchment study area and have conducted surveys of topography, soils, and vegetation. Our preliminary results indicate that although runoff makes up less than 10% of the annual water budget, runoff events - which are frequent in the summer - are capable of moving large amounts of sediment. We estimate that between July 1993 and October 1994, between 25,000 and 50,000 kg of sediment has eroded and been transported from the catchment. The information gained from such studies is essential to our ability to formulate effective strategies for managing these rapidly eroding woodlands

The SiBI connector: a new medical device to facilitate preoxygenation and reduce waste anesthetic gases during inhaled induction with sevoflurane.

Science.gov (United States)

Colas, M J; Tétrault, J P; Dumais, L; Truong, P; Claprood, Y; Martin, R

2000-12-01

The SiBI connector is a new medical device used for vital capacity inhaled induction with sevoflurane. It allows efficient preoxygenation of patients and reduces waste anesthetic gases in the operation room during induction.

Assessment of ground water contamination in Erode District ...

African Journals Online (AJOL)

admin

A systematic study has been carried out to assess the water contamination and the effect of the tanneries and dyeing industries effluents on Erode District, Tamil Nadu. Ten (10) sampling locations were selected in and around industries. The water samples were collected from the selected sampling points. The samples ...

Wind-eroded silicate as a source of hydrogen peroxide on Mars

DEFF Research Database (Denmark)

Bak, Ebbe Norskov; Merrison, Jonathan P.; Jensen, Svend Knak

-sists of silicates [4] that due to wind erosion has a very fine grained texture. Based on the composition of the surface material and investigations showing that crushing of silicates can give rise to reactive oxygen species [5], we hypothesized that wind erosion of silicates can explain the reactivity of Martian...... soil. Wind-erosion of silicate could thus be one of several causes of the soil’s reactivity. As our experiments show, the globally distributed wind eroded silicate dust can lead to the production of hydrogen peroxide which might explain the reactivity of the Martian soil. The reactivity of eroded...

Water and dissolved carbon transport in an eroding soil landscape using column experiments

DEFF Research Database (Denmark)

Rieckh, Helene; Gerke, Horst; Glæsner, Nadia

2014-01-01

In the hummocky ground moraine soil landscape, a spatial continuum of more or less eroded soils developed from till under intensive agricultural cultivation. Water flow and solute transport are affected by the variable soil structural and pedological developments, which are posing a challenge...... for flux estimation. The objective of this study was to investigate transport of water, dissolved organic (DOC), and particulate carbon (PC) through soil profiles of an eroded Haplic Luvisol and a heavily eroded Haplic Regosol. We studied 5 soil horizons in three replicates each: Ap (0-20 cm) and E (20...... boundary. Breakthrough curves for a pre-applied tracer (Br-) on the soil surface and a tracer applied with irrigation water (3H2O) were modeled analytically using CXTFIT. The heterogeneity of the Luvisol horizons was generally higher than that of the Regosol horizons, which relates to the higher...

Eroded dentin does not jeopardize the bond strength of adhesive restorative materials

Directory of Open Access Journals (Sweden)

Janaina Barros Cruz

2012-08-01

Full Text Available This in vitro study evaluated the bond strength of adhesive restorative materials to sound and eroded dentin. Thirty-six bovine incisors were embedded in acrylic resin and ground to obtain flat buccal dentin surfaces. Specimens were randomly allocated in 2 groups: sound dentin (immersion in artificial saliva and eroded dentin (pH cycling model - 3× / cola drink for 7 days. Specimens were then reassigned according to restorative material: glass ionomer cement (KetacTM Molar Easy Mix, resin-modified glass ionomer cement (VitremerTM or adhesive system with resin composite (Adper Single Bond 2 + Filtek Z250. Polyethylene tubes with an internal diameter of 0.76 mm were placed over the dentin and filled with the material. The microshear bond test was performed after 24 h of water storage at 37ºC. The failure mode was evaluated using a stereomicroscope (400×. Bond strength data were analyzed with two-way ANOVA and Tukey's post hoc tests (α = 0.05. Eroded dentin showed bond strength values similar to those for sound dentin for all materials. The adhesive system showed the highest bond strength values, regardless of the substrate (p < 0.0001. For all groups, the adhesive/mixed failure prevailed. In conclusion, adhesive materials may be used in eroded dentin without jeopardizing the bonding quality. It is preferable to use an etch-and-rinse adhesive system because it shows the highest bond strength values compared with the glass ionomer cements tested.

Interrill and rill erodibility in the northern andean highlands

NARCIS (Netherlands)

Romero, C.; Stroosnijder, L.; Baigorria, G.A.

2007-01-01

There is a lack of quantitative information describing the physical processes causing soil erosion in the Andean Highlands, especially those related to interrill and rill erodibility factors. To assess how susceptible are soils to erosion in this region, field measurements of interrill (Ki) and rill

sessment of ground water contamination in Erode District, Tamilnadu

African Journals Online (AJOL)

A systematic study has been carried out to assess the water contamination and the effect of the tanneries and dyeing industries effluents on Erode District, Tamil Nadu. Ten (10) sampling locations were selected in and around industries. The water samples were collected from the selected sampling points. The samples ...

Physico-chemical properties and fertility status of water eroded soils of Sharkul area of district Mansehra, Pakistan

Directory of Open Access Journals (Sweden)

Farmanullah Khan, A. Iqbal

2011-11-01

Full Text Available Soil degradation is the major threat to agricultural sustainability because it affects the soil productivity. Present study was conducted in 2008 to evaluate physico-chemical properties and fertility status of some eroded soil series of Sharkul area district Manshera, Hazara division, Khyber Pakhtunkhwa, Pakistan. Six soil series including slightly eroded (Dosera and Girari, moderately eroded (Nakholi and Sharkul and severely eroded (Ahl and Banser were selected. Soil samples were collected from surface (0-15 cm, subsurface (30-45 cm and substrata soil (60-75cm depths and were analyzed for various soil properties. Due to severity of erosion, bulk density increased, while total porosity, saturation percentage and organic matter decreased significantly. AB-DTPA extractable P, K, Fe, Cu, Zn, and Mn concentrations were decreased due to the severity of erosion in surface and sub surface soils, whereas in the substrata soils (60-75 cm depth, the effect of erosion was almost non significant. Sub-surface and sub-strata soils were found deficient in available P ( Zn > Fe > Mn. The physical and chemical properties of eroded soils varied significantly and the increasing severity of erosion resulted in corresponding deterioration of soil quality.

The Influence of Eroded Blades on Wind Turbine Performance Using Numerical Simulations

Directory of Open Access Journals (Sweden)

Matthias Schramm

2017-09-01

Full Text Available During their operation, wind turbine blades are eroded due to rain and hail, or they are contaminated with insects. Since the relative inflow velocity is higher at the outer than at the inner part of the blades, erosion occurs mostly at the outer blade region. In order to prevent strong erosion, it is possible to install a leading edge protection, which can be applied to the blades after the initial installation, but changes the shape of the initial airfoil sections. It is unclear how this modification influences the aerodynamic performance of the turbine. Hence, it is investigated in this work. The NREL 5 MW turbine is simulated with clean and eroded blades, which are compared to coated blades equipped with leading edge protection. Aerodynamic polars are generated by means of Computational Fluid Dynamics, and load calculations are conducted using the blade element momentum theory. The analysis in this work shows that, compared to clean rotor blades, the worse aerodynamic behaviour of strongly eroded blades can lead to power losses of 9 % . In contrast, coated blades only have a small impact on the turbine power of less than 1 % .

Induction-heating MOCVD reactor with significantly improved heating efficiency and reduced harmful magnetic coupling

KAUST Repository

Li, Kuang-Hui; Alotaibi, Hamad S.; Sun, Haiding; Lin, Ronghui; Guo, Wenzhe; Torres-Castanedo, Carlos G.; Liu, Kaikai; Galan, Sergio V.; Li, Xiaohang

2018-01-01

In a conventional induction-heating III-nitride metalorganic chemical vapor deposition (MOCVD) reactor, the induction coil is outside the chamber. Therefore, the magnetic field does not couple with the susceptor well, leading to compromised heating efficiency and harmful coupling with the gas inlet and thus possible overheating. Hence, the gas inlet has to be at a minimum distance away from the susceptor. Because of the elongated flow path, premature reactions can be more severe, particularly between Al- and B-containing precursors and NH3. Here, we propose a structure that can significantly improve the heating efficiency and allow the gas inlet to be closer to the susceptor. Specifically, the induction coil is designed to surround the vertical cylinder of a T-shaped susceptor comprising the cylinder and a top horizontal plate holding the wafer substrate within the reactor. Therefore, the cylinder coupled most magnetic field to serve as the thermal source for the plate. Furthermore, the plate can block and thus significantly reduce the uncoupled magnetic field above the susceptor, thereby allowing the gas inlet to be closer. The results show approximately 140% and 2.6 times increase in the heating and susceptor coupling efficiencies, respectively, as well as a 90% reduction in the harmful magnetic flux on the gas inlet.

Induction-heating MOCVD reactor with significantly improved heating efficiency and reduced harmful magnetic coupling

KAUST Repository

Li, Kuang-Hui

2018-02-23

In a conventional induction-heating III-nitride metalorganic chemical vapor deposition (MOCVD) reactor, the induction coil is outside the chamber. Therefore, the magnetic field does not couple with the susceptor well, leading to compromised heating efficiency and harmful coupling with the gas inlet and thus possible overheating. Hence, the gas inlet has to be at a minimum distance away from the susceptor. Because of the elongated flow path, premature reactions can be more severe, particularly between Al- and B-containing precursors and NH3. Here, we propose a structure that can significantly improve the heating efficiency and allow the gas inlet to be closer to the susceptor. Specifically, the induction coil is designed to surround the vertical cylinder of a T-shaped susceptor comprising the cylinder and a top horizontal plate holding the wafer substrate within the reactor. Therefore, the cylinder coupled most magnetic field to serve as the thermal source for the plate. Furthermore, the plate can block and thus significantly reduce the uncoupled magnetic field above the susceptor, thereby allowing the gas inlet to be closer. The results show approximately 140% and 2.6 times increase in the heating and susceptor coupling efficiencies, respectively, as well as a 90% reduction in the harmful magnetic flux on the gas inlet.

75 FR 75961 - Notice of Implementation of the Wind Erosion Prediction System for Soil Erodibility System...

Science.gov (United States)

2010-12-07

... implementation of the WEPS system does not affect the Highly Erodible Map Unit List contained in the NRCS Field Office Technical Guide as of January 1, 1990. This 1990 list will continue to be used for all erodibility... plant damage, and predict PM-10 emissions when wind speeds exceed the erosion threshold. The WEPS model...

Eroded Layered Material in Southwest Utopia Planitia

Science.gov (United States)

1999-01-01

Images from the Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC)dramatically illustrate that many places on the red planet have outcrops of layered geologic materials. The two pictures above show the remains of layered material inside craters in southwestern Utopia Planitia (see inset for detailed view). These remnant layers indicate that the craters--and perhaps the plains that surround them--were once buried beneath a deposit that has since been eroded away. This theme of layered outcrops and exhumed craters appears to be one of the dominant observations that MGS MOC has made--to date--about Mars. The origin and composition of the layered material--and its ultimate fate once it was largely eroded away--are unknown. Each of the two pictures shown here covers an area about 4 kilometers (2.5 miles)by 6.3 kilometers (3.9 miles). Illumination is from the lower right. These are subframes of a single MOC image acquired in July 1998 during the MGS Science Phasing Orbits imaging campaign. This figure was presented at the 30th Lunar and Planetary Science Conference in Houston, Texas, March 1999. Malin Space Science Systems and the California Institute of Technology built the MOC using spare hardware from the Mars Observer mission. MSSS operates the camera from its facilities in San Diego, CA. The Jet Propulsion Laboratory's Mars Surveyor Operations Project operates the Mars Global Surveyor spacecraft with its industrial partner, Lockheed Martin Astronautics, from facilities in Pasadena, CA and Denver, CO.

Highly erodible terrain in agriculture land against chipped pruned branches. Or how to stop the soil erosion with low investment

Science.gov (United States)

Cerdà, A.

2009-04-01

The session on "Soil erosion and sediment control with vegetation and bioengineering on severely eroded terrain" pays special attention to the severe soil erosion suffered on steep slopes and erodible parent materials and soils. Within the last 20 years, in the Mediterranean lands, the citrus orchards were reallocated on steep slopes due to the urban development and better climatic and management conditions of the new plantations. The lack of vegetation cover on the new slope plantations of citrus resulted in high erosion rates. Those non-sustainable soil losses were measured by means of rainfall simulation experiments, Gerlach collectors, geomorphological transect and topographical measurements. The October 2007 and October 2008 rainy periods resulted in sheet, rill and gully erosion. Some recently planted orchards (2005) had the first pruning season in 2008. The pruned chipped branches reduced the soil losses to 50 % of the expected, although the litter (pruned branches) covered 4.67 % of the soil. This is why a research was developed by means of simulated rainfall experiments to determine the vegetation cover (litter, mainly leaves) to protect the soil to reach a sustainable erosion rate. Rainfall simulation experiments at 43 mm h-1 where performed on 1 m2 plots covered with 0, 3, 7, 15, 30, 45, 60, 80 and 100 % litter cover (pruned chipped branches) to determine the sustainable litter cover to avoid the soil losses. The results show that more that 45 % litter cover almost reduces the soil losses to negligible rates. The results confirm that 4 % of vegetation cover reduces the soil losses to 50 %. Key words: Agriculture land, erodible terrain, land management, citrus, erosion, Spain, Valencia, herbicides. Acknowledgements, We thanks the financial support of the Ministerio de Ciencia e Innovación by means of the project CGL2008-02879/BTE, "PERDIDA DE SUELO EN NUEVAS EXPLOTACIONES CITRICOLAS EN PENDIENTE. ESTRATEGIAS PARA EL CONTROL DE LA EROSION HIDRICA"

A Hydrodynamic and Sediment Transport Model for the Waipaoa Shelf, New Zealand: Sensitivity of Fluxes to Spatially-Varying Erodibility and Model Nesting

Directory of Open Access Journals (Sweden)

Julia M. Moriarty

2014-04-01

Full Text Available Numerical models can complement observations in investigations of marine sediment transport and depositional processes. A coupled hydrodynamic and sediment transport model was implemented for the Waipaoa River continental shelf offshore of the North Island of New Zealand, to complement a 13-month field campaign that collected seabed and hydrodynamic measurements. This paper described the formulations used within the model, and analyzed the sensitivity of sediment flux estimates to model nesting and seabed erodibility. Calculations were based on the Regional Ocean Modeling System—Community Sediment Transport Modeling System (ROMS-CSTMS, a primitive equation model using a finite difference solution to the equations for momentum and water mass conservation, and transport of salinity, temperature, and multiple classes of suspended sediment. The three-dimensional model resolved the complex bathymetry, bottom boundary layer, and river plume that impact sediment dispersal on this shelf, and accounted for processes including fluvial input, winds, waves, tides, and sediment resuspension. Nesting within a larger-scale, lower resolution hydrodynamic model stabilized model behavior during river floods and allowed large-scale shelf currents to impact sediment dispersal. To better represent observations showing that sediment erodibility decreased away from the river mouth, the seabed erosion rate parameter was reduced with water depth. This allowed the model to account for the observed spatial pattern of erodibility, though the model held the critical shear stress for erosion constant. Although the model neglected consolidation and swelling processes, use of a spatially-varying erodibility parameter significantly increased export of fluvial sediment from Poverty Bay to deeper areas of the shelf.

Bond strength and interfacial morphology of orthodontic brackets bonded to eroded enamel treated with calcium silicate-sodium phosphate salts or resin infiltration.

Science.gov (United States)

Costenoble, Aline; Vennat, Elsa; Attal, Jean-Pierre; Dursun, Elisabeth

2016-11-01

 To investigate the shear bond strength (SBS) of orthodontic brackets bonded to eroded enamel treated with preventive approaches and to examine the enamel/bracket interfaces.  Ninety-one brackets were bonded to seven groups of enamel samples: sound; eroded; eroded+treated with calcium silicate-sodium phosphate salts (CSP); eroded+infiltrated by ICON ® ; eroded+infiltrated by ICON ® and brackets bonded with 1-month delay; eroded+infiltrated by an experimental resin; and eroded+infiltrated by an experimental resin and brackets bonded with 1-month delay. For each group, 12 samples were tested in SBS and bond failure was assessed with the adhesive remnant index (ARI); one sample was examined using scanning electron microscopy (SEM).  Samples treated with CSP or infiltration showed no significant differences in SBS values with sound samples. Infiltrated samples followed by a delayed bonding showed lower SBS values. All of the values remained acceptable. The ARI scores were significantly higher for sound enamel, eroded, and treated with CSP groups than for all infiltrated samples. SEM examinations corroborated the findings.  Using CSP or resin infiltration before orthodontic bonding does not jeopardize the bonding quality. The orthodontic bonding should be performed shortly after the resin infiltration.

Heme oxygenase-1 induction improves cardiac function following myocardial ischemia by reducing oxidative stress.

Directory of Open Access Journals (Sweden)

Yossi Issan

Full Text Available Oxidative stress plays a key role in exacerbating diabetes and cardiovascular disease. Heme oxygenase-1 (HO-1, a stress response protein, is cytoprotective, but its role in post myocardial infarction (MI and diabetes is not fully characterized. We aimed to investigate the protection and the mechanisms of HO-1 induction in cardiomyocytes subjected to hypoxia and in diabetic mice subjected to LAD ligation.In vitro: cultured cardiomyocytes were treated with cobalt-protoporphyrin (CoPP and tin protoporphyrin (SnPP prior to hypoxic stress. In vivo: CoPP treated streptozotocin-induced diabetic mice were subjected to LAD ligation for 2/24 h. Cardiac function, histology, biochemical damage markers and signaling pathways were measured.HO-1 induction lowered release of lactate dehydrogenase (LDH and creatine phospho kinase (CK, decreased propidium iodide staining, improved cell morphology and preserved mitochondrial membrane potential in cardiomyocytes. In diabetic mice, Fractional Shortening (FS was lower than non-diabetic mice (35±1%vs.41±2, respectively p<0.05. CoPP-treated diabetic animals improved cardiac function (43±2% p<0.01, reduced CK, Troponin T levels and infarct size compared to non-treated diabetic mice (P<0.01, P<0.001, P<0.01 respectively. CoPP-enhanced HO-1 protein levels and reduced oxidative stress in diabetic animals, as indicated by the decrease in superoxide levels in cardiac tissues and plasma TNFα levels (p<0.05. The increased levels of HO-1 by CoPP treatment after LAD ligation led to a shift of the Bcl-2/bax ratio towards the antiapoptotic process (p<0.05. CoPP significantly increased the expression levels of pAKT and pGSK3β (p<0.05 in cardiomyocytes and in diabetic mice with MI. SnPP abolished CoPP's cardioprotective effects.HO-1 induction plays a role in cardioprotection against hypoxic damage in cardiomyocytes and in reducing post ischemic cardiac damage in the diabetic heart as proved by the increased levels of pAKT with

Predicting of soil erosion with regarding to rainfall erosivity and soil erodibility

Science.gov (United States)

Suif, Zuliziana; Razak, Mohd Amirun Anis Ab; Ahmad, Nordila

2018-02-01

The soil along the hill and slope are wearing away due to erosion and it can take place due to occurrence of weak and heavy rainfall. The aim of this study is to predict the soil erosion degree in Universiti Pertahanan Nasional Malaysia (UPNM) area focused on two major factor which is soil erodibility and rainfall erosivity. Soil erodibility is the possibilities of soil to detach and carried away during rainfall and runoff. The "ROM" scale was used in this study to determine the degree of soil erodibility, namely low, moderate, high, and very high. As for rainfall erosivity, the erosive power caused by rainfall that cause soil loss. A daily rainfall data collected from January to April was analyzed by using ROSE index classification to identify the potential risk of soil erosion. The result shows that the soil erodibilty are moderate at MTD`s hill, high at behind of block Lestari and Landslide MTD hill, and critical at behind the mess cadet. While, the highest rainfall erosivity was recorded in March and April. Overall, this study would benefit the organization greatly in saving cost in landslide protection as relevant authorities can take early measures repairing the most affected area of soil erosion.

Wind-Eroded Silicate as a Source of Hydrogen Peroxide on Mars

Science.gov (United States)

Bak, E. N.; Merrison, J. P.; Jensen, S. K.; Nørnberg, P.; Finster, K.

2014-07-01

Laboratory simulations show that wind-eroded silicate can be a source of hydrogen peroxide. The ubiquitous, fine-grained silicate dust might thus explain the oxidizing properties of the martian soil and affect the preservation of organic compounds.

Quality Uncertainty Erodes Trust in Science

Directory of Open Access Journals (Sweden)

Simine Vazire

2017-02-01

Full Text Available When consumers of science (readers and reviewers lack relevant details about the study design, data, and analyses, they cannot adequately evaluate the strength of a scientific study. Lack of transparency is common in science, and is encouraged by journals that place more emphasis on the aesthetic appeal of a manuscript than the robustness of its scientific claims. In doing this, journals are implicitly encouraging authors to do whatever it takes to obtain eye-catching results. To achieve this, researchers can use common research practices that beautify results at the expense of the robustness of those results (e.g., p-hacking. The problem is not engaging in these practices, but failing to disclose them. A car whose carburetor is duct-taped to the rest of the car might work perfectly fine, but the buyer has a right to know about the duct-taping. Without high levels of transparency in scientific publications, consumers of scientific manuscripts are in a similar position as buyers of used cars – they cannot reliably tell the difference between lemons and high quality findings. This phenomenon – quality uncertainty – has been shown to erode trust in economic markets, such as the used car market. The same problem threatens to erode trust in science. The solution is to increase transparency and give consumers of scientific research the information they need to accurately evaluate research. Transparency would also encourage researchers to be more careful in how they conduct their studies and write up their results. To make this happen, we must tie journals’ reputations to their practices regarding transparency. Reviewers hold a great deal of power to make this happen, by demanding the transparency needed to rigorously evaluate scientific manuscripts. The public expects transparency from science, and appropriately so – we should be held to a higher standard than used car salespeople.

Incorporation of Fine-Grained Sediment Erodibility Measurements into Sediment Transport Modeling, Capitol Lake, Washington

Science.gov (United States)

Stevens, Andrew W.; Gelfenbaum, Guy; Elias, Edwin; Jones, Craig

2008-01-01

Capitol Lake was created in 1951 with the construction of a concrete dam and control gate that prevented salt-water intrusion into the newly formed lake and regulated flow of the Deschutes River into southern Puget Sound. Physical processes associated with the former tidally dominated estuary were altered, and the dam structure itself likely caused an increase in retention of sediment flowing into the lake from the Deschutes River. Several efforts to manage sediment accumulation in the lake, including dredging and the construction of sediment traps upriver, failed to stop the lake from filling with sediment. The Deschutes Estuary Feasibility Study (DEFS) was carried out to evaluate the possibility of removing the dam and restoring estuarine processes as an alternative ongoing lake management. An important component of DEFS was the creation of a hydrodynamic and sediment transport model of the restored Deschutes Estuary. Results from model simulations indicated that estuarine processes would be restored under each of four restoration alternatives, and that over time, the restored estuary would have morphological features similar to the predam estuary. The model also predicted that after dam-removal, a large portion of the sediment eroded from the lake bottom would be deposited near the Port of Olympia and a marina located in lower Budd Inlet seaward of the present dam. The volume of sediment transported downstream was a critical piece of information that managers needed to estimate the total cost of the proposed restoration project. However, the ability of the model to predict the magnitude of sediment transport in general and, in particular, the volume of sediment deposition in the port and marina was limited by a lack of information on the erodibility of fine-grained sediments in Capitol Lake. Cores at several sites throughout Capitol Lake were collected between October 31 and November 1, 2007. The erodibility of sediments in the cores was later determined in the

Effect of CPP-ACP on the remineralization of acid-eroded human tooth enamel: nanomechanical properties and microtribological behaviour study

International Nuclear Information System (INIS)

Zheng, L; Zheng, J; Zhang, Y F; Qian, L M; Zhou, Z R

2013-01-01

Casein phosphopeptide-stabilized amorphous calcium phosphate (CPP-ACP) has been used to enhance tooth remineralization in the dental clinic. But the contribution of CPP-ACP to the remineralization of acid-eroded human tooth enamel is of widespread controversy. To confirm the application potential of CPP-ACP in the remineralization repair of tooth erosion caused by acid-attack, the effect of remineralization in vitro in 2% w/v CPP-ACP solution on the acid-eroded human tooth enamel was investigated in this study. The repair of surface morphology and the improvement of nanomechanical and microtribological properties were characterized with laser confocal scanning microscope, scanning electron microscope, nanoindentation tester and nanoscratch tester. Results showed that a layer of uneven mineral deposits, which were mainly amorphous calcium phosphate (ACP) in all probability, was observed on the acid-eroded enamel surface after remineralization. Compared with the acid-eroded enamel surface, the nanoindentation hardness and Young's modulus of the remineralized enamel surface obviously increased. Both the friction coefficient and wear volume of the acid-eroded enamel surface decreased after remineralization. However, both the nanomechanical and the anti-wear properties of the remineralized enamel surface were still inferior to those of original enamel surface. In summary, tooth damage caused by acid erosion could be repaired by remineralization in CPP-ACP solution, but the repair effect, especially on the nanomechanical and anti-wear properties of the acid-eroded enamel, was limited. These results would contribute to a further exploration of the remineralization potential of CPP-ACP and a better understanding of the remineralization repair mechanism for acid-eroded human tooth enamel. (paper)

Effect of CPP-ACP on the remineralization of acid-eroded human tooth enamel: nanomechanical properties and microtribological behaviour study

Science.gov (United States)

Zheng, L.; Zheng, J.; Zhang, Y. F.; Qian, L. M.; Zhou, Z. R.

2013-10-01

Casein phosphopeptide-stabilized amorphous calcium phosphate (CPP-ACP) has been used to enhance tooth remineralization in the dental clinic. But the contribution of CPP-ACP to the remineralization of acid-eroded human tooth enamel is of widespread controversy. To confirm the application potential of CPP-ACP in the remineralization repair of tooth erosion caused by acid-attack, the effect of remineralization in vitro in 2% w/v CPP-ACP solution on the acid-eroded human tooth enamel was investigated in this study. The repair of surface morphology and the improvement of nanomechanical and microtribological properties were characterized with laser confocal scanning microscope, scanning electron microscope, nanoindentation tester and nanoscratch tester. Results showed that a layer of uneven mineral deposits, which were mainly amorphous calcium phosphate (ACP) in all probability, was observed on the acid-eroded enamel surface after remineralization. Compared with the acid-eroded enamel surface, the nanoindentation hardness and Young's modulus of the remineralized enamel surface obviously increased. Both the friction coefficient and wear volume of the acid-eroded enamel surface decreased after remineralization. However, both the nanomechanical and the anti-wear properties of the remineralized enamel surface were still inferior to those of original enamel surface. In summary, tooth damage caused by acid erosion could be repaired by remineralization in CPP-ACP solution, but the repair effect, especially on the nanomechanical and anti-wear properties of the acid-eroded enamel, was limited. These results would contribute to a further exploration of the remineralization potential of CPP-ACP and a better understanding of the remineralization repair mechanism for acid-eroded human tooth enamel.

Impact of land use change on soil erodibility

Directory of Open Access Journals (Sweden)

F. Taleshian Jeloudar

2018-01-01

Full Text Available Vulnerability of soil separates to detachment by water is described as soil erodibility by Universal Soil Loss Equation which can be affected by land use change. In this study it was attempted to quantify the changes of Universal Soil Loss Equation K-factor and its soil driving factors in three land uses including rangeland, rainfed farming, and orchards in Babolrood watershed, northern Iran. Soil composite samples were obtained from two layers in three land uses, and the related soil physico-chemical properties were measured. The rainfed farming land use showed the highest clay contents, but the highest amounts of soil organic matter and sand particles were found in orchard land use. The high intensity of tillage led to the significant decrease of soil aggregate stability and permeability in the rainfed farming land use. The Universal Soil Loss Equation K-factor was negatively correlated with soil permeability (r=-0.77**. In rangeland, the K-factor (0.045 Mg h/MJ/mm was significantly higher and the particle size distribution had a great impact on the K-factor. The orchard land use, converted from the rangeland, did not show any increase of soils erodibility and can potentially be introduced as a good alternative land use in sloping areas. However, more detailed studies on environmental, social and economic aspects of this land use are needed.

Design of Controller for Reducing In-Rush Current of Single-Phase Induction Motor

Energy Technology Data Exchange (ETDEWEB)

Park, Su Kang; Baek, Hyung Lae; Lee, Sang Il [Chosun University, Kwangju (Korea)

2001-05-01

During an AC motor's start-up accelerating period, a large amount of current is required to reach to the rating speed. This is called in-rush current. This peak in-rush current can be more than about several times the operating or steady-state current in the full load rating of the motor. In-rush current is present in both and electronic ballasts. The main area of concern is the tripping of circuit breaker and fuses which can affect electrical system components From this, we can see that the electrical power controllers will be rather concerned, since they have to supply the actual current necessary to start the motor. This paper presents a new method to reducing in-rush current and energy saving of the single-phase induction motor used in air-conditioner. It can be obtained that proposed system is low cost and small size as compared with other controller. Experiments are focused on a capacitor starting single-phase induction motor. The optimal power saving and in-rush current limiting by phase angle control are verified by experimental results. Also, auxiliary winding was controlled by electronic starting switch. (author). 10 refs., 13 figs., 2 tabs.

Distribution of Shrubland and Grassland Soil Erodibility on the Loess Plateau

Directory of Open Access Journals (Sweden)

Xiao Zhang

2018-06-01

Full Text Available Soil erosion is one of the most severe problems facing environments and has increased throughout the 20th century. Soil erodibility (K-factor is one of the important indicators of land degradation, and many models have been used to estimate K values. Although soil erodibility has been estimated, the comparison of different models and their usage at a regional scale and, in particular, for different land use types, need more research. Four of the most widely distributed land use types were selected to analyze, including introduced and natural grassland, as well as introduced and natural shrubland. Soil particle size, soil organic matter and other relevant soil properties were measured to estimate soil erodibility in the Loess Plateau. The results show that: (1 the erosion productivity impact calculator (EPIC model and SHIRAZI model are both suitable for the Loess Plateau, while the SHIRAZI model has the advantage of fewer parameters; (2 introduced grassland has better ability to protect both the 0–5 cm soils and 5–20 cm soils, while the differences between introduced and natural shrubland are not obvious at a catchment scale; (3 the K values of introduced grassland, natural grassland, introduced shrubland and natural shrubland in the 0–5 cm layer vary from 0.008 to 0.037, 0.031 to 0.046, 0.012 to 0.041 and 0.008 to 0.045 (t·hm2·h/(MJ·mm·hm2, while the values vary from 0.009 to 0.039, 0.032 to 0.046, 0.012 to 0.042 and 0.008 to 0.048 (t·hm2·h/(MJ·mm·hm2 in the 5–20 cm layer. The areas with a mean multiyear precipitation of 370–440 mm are the most important places for vegetation restoration construction management at a regional scale. A comprehensive balance between water conservation and soil conservation is needed and important when selecting the species used to vegetation restoration. This study provides suggestions for ecological restoration and provides a case study for the estimate of soil erodibility in arid and semiarid

Continuum modeling of ion-beam eroded surfaces under normal incidence: Impact of stochastic fluctuations

International Nuclear Information System (INIS)

Dreimann, Karsten; Linz, Stefan J.

2010-01-01

Graphical abstract: Deterministic surface pattern (left) and its stochastic counterpart (right) arising in a stochastic damped Kuramoto-Sivashinsky equation that serves as a model equation for ion-beam eroded surfaces and is systematically investigated. - Abstract: Using a recently proposed field equation for the surface evolution of ion-beam eroded semiconductor target materials under normal incidence, we systematically explore the impact of additive stochastic fluctuations that are permanently present during the erosion process. Specifically, we investigate the dependence of the surface roughness, the underlying pattern forming properties and the bifurcation behavior on the strength of the fluctuations.

[Characteristics of Soil Respiration along Eroded Sloping Land with Different SOC Background on the Hilly Loess Plateau].

Science.gov (United States)

Chen, Gai; Xu, Ming-xiang; Zhang, Ya-feng; Wang, Chao-hua; Fan, Hui-min; Wang, Shan-shan

2015-09-01

This study aimed to characterize soil respiration along eroded sloping land at erosion and deposition area under different soil organic carbon(SOC) levels, and linked the relationship between soil respiration and soil temperature, soil moisture, SOC and slope position. Experiments were carried out in the plots of S type slopes include five different soil organic carbon levels in the Loess Hilly Region. The S type slopes were divided into control area at the top of the slope, erosion area at the middle of the slope and deposition area at the toe of the slope. We found that soil temperature had a greater impact on soil respiration in the deposition area, whereas soil moisture had a greater impact on soil respiration in the erosion area compared among control area, erosion area and deposition area. In addition, SOC was the most important factor affecting soil respiration, which can explain soil respiration variation 54. 72%, followed by soil moisture, slope position and soil temperature, which explain soil respiration variation 18. 86% , 16. 13% and 10. 29%, respectively. Soil respiration response to erosion showed obvious on-site and off-site effects along the eroded sloping land. Soil respiration in the erosion area was reduced by 21. 14% compared with control area, and soil respiration in the deposition area was increased by 21. 93% compared with control area. Erosion effect on source and sink of carbon emission was correlated with SOC content of the eroded sloping land. When SOC content was higher than 6. 82 g.kg-1, the slope. erosion tended to be a carbon sequestration process, and when SOC content was lower than 3.03 g.kg-1, the slope erosion tended to be a process of the carbon emission source. The model could reflect the relationship between soil respiration and independent variables of soil organic carbon content, soil temperature and moisture.

Reducing the Lift-Off Effect on Permeability Measurement for Magnetic Plates From Multifrequency Induction Data

OpenAIRE

Lu, Mingyang; Zhu, Wenqian; Yin, Liyuan; Peyton, Anthony J.; Yin, Wuliang; Qu, Zhigang

2017-01-01

Lift-off variation causes errors in eddy current measurement of nonmagnetic plates as well as magnetic plates. For nonmagnetic plates, previous work has been carried out to address the issue. In this paper, we follow a similar strategy, but try to reduce the lift-off effect on another index--zero-crossing frequency for magnetic plates. This modified index, termed as the compensated zero-crossing frequency, can be obtained from the measured multifrequency inductance spectral data using the alg...

Geomorphology and forest management in New Zealand's erodible steeplands: An overview

Science.gov (United States)

Phillips, Chris; Marden, Michael; Basher, Les R.

2018-04-01

In this paper we outline how geomorphological understanding has underpinned forest management in New Zealand's erodible steeplands, where it contributes to current forest management, and suggest where it will be of value in the future. We focus on the highly erodible soft-rock hill country of the East Coast region of North Island, but cover other parts of New Zealand where appropriate. We conclude that forestry will continue to make a significant contribution to New Zealand's economy, but several issues need to be addressed. The most pressing concerns are the incidence of post-harvest, storm-initiated landslides and debris flows arising from steepland forests following timber harvesting. There are three areas where geomorphological information and understanding are required to support the forest industry - development of an improved national erosion susceptibility classification to support a new national standard for plantation forestry; terrain analysis to support improved hazard and risk assessment at detailed operational scales; and understanding of post-harvest shallow landslide-debris flows, including their prediction and management.

Vector control of induction machines

CERN Document Server

Robyns, Benoit

2012-01-01

After a brief introduction to the main law of physics and fundamental concepts inherent in electromechanical conversion, ""Vector Control of Induction Machines"" introduces the standard mathematical models for induction machines - whichever rotor technology is used - as well as several squirrel-cage induction machine vector-control strategies. The use of causal ordering graphs allows systematization of the design stage, as well as standardization of the structure of control devices. ""Vector Control of Induction Machines"" suggests a unique approach aimed at reducing parameter sensitivity for

Effects of human pharmaceuticals on cytotoxicity, EROD activity and ROS production in fish hepatocytes

International Nuclear Information System (INIS)

Laville, N.; Aiet-Aiessa, S.; Gomez, E.; Casellas, C.; Porcher, J.M.

2004-01-01

Pharmaceuticals are found in the aquatic environment but their potential effects on non-target species like fish remain unknown. This in vitro study is a first approach in the toxicity assessment of human drugs on fish. Nine pharmaceuticals were tested on two fish hepatocyte models: primary cultures of rainbow trout hepatocytes (PRTH) and PLHC-1 fish cell line. Cell viability, interaction with cytochrome P450 1A (CYP1A) enzyme and oxidative stress were assessed by using 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrasodium bromide tetrazolium (MTT), 7-ethoxyresorufin-o-deethylase (EROD) and dichlorofluorescein (DCFH-DA) assays, respectively. The tested drugs were clofibrate (CF), fenofibrate (FF), carbamazepine (CBZ), fluoxetine (FX), diclofenac (DiCF), propranolol (POH), sulfamethoxazole (SFX), amoxicillin (AMX) and gadolinium chloride (GdCl 3 ). All substances were cytotoxic, except AMX at concentration up to 500 μM. The calculated MTT EC 50 values ranged from 2 μM (CF) to 651 μM (CBZ) in PLHC-1, and from 53 μM (FF) to 962 μM (GdCl 3 ) in PRTH. CF, FF, and FX were the most cytotoxic drugs and induced oxidative stress before being cytotoxic. Compared to hepatocytes from human and dog, fish hepatocytes seemed to be more susceptible to the peroxisome proliferators (PPs) CF and FF. In PLHC-1 cells none of the tested drugs induced the EROD activity whereas POH appeared as a weak EROD inducer in PRTH. Moreover, in PRTH, SFX, DiCF, CBZ and to a lesser extend, FF and CF inhibited the basal EROD activity at clearly sublethal concentrations which may be of concern at the biological and chemical levels in a multipollution context

Bond Stability of a Universal Adhesive System to Eroded/Abraded Dentin After Deproteinization.

Science.gov (United States)

Augusto, M G; Torres, Crg; Pucci, C R; Schlueter, N; Borges, A B

Erosive/abrasive challenges can potentially compromise bonding to dentin. Aiming to improve the quality and stability of bonding to this substrate, this study investigated the combined effect of erosion and toothbrush abrasion on the microtensile bond strength (μTBS) stability to dentin using a universal adhesive system in total and self-etching modes, associated or not associated with deproteinization. Bovine dentin specimens were divided into five groups according to the organic matrix condition (n=20): control (C); erosion (E); erosion + abrasion (EA); erosion + sodium hypochlorite (EH); erosion + abrasion + sodium hypochlorite (EAH). The groups were further divided (n=10) according to the mode of application (total or self-etching) of a universal adhesive. After the bonding procedure, composite blocks were built up, and the samples were cut to obtain sticks for μTBS testing. For each specimen, one-half of the sticks was immediately tested, and the other one-half was tested after artificial aging (5000 thermocycles, 5°C and 55°C). Three-way analysis of variance (α=5%) showed a significant difference for the triple interaction ( p=0.0007). Higher μTBS means were obtained for the EH and EAH groups compared with the E and EA groups. The control group showed immediate μTBS values similar to that of the E and EA groups for both bond strategies. Erosion and erosion/abrasion did not significantly influence the immediate μTBS to dentin. Artificial aging reduced μTBS values for the groups C, E, and EA using the total-etching mode. Deproteinization maintained the bond stability to artificially aged eroded and eroded/abraded dentin.

Induction of liver monooxygenases by annatto and bixin in female rats

Directory of Open Access Journals (Sweden)

A.C.A.X. De-Oliveira

2003-01-01

Full Text Available Annatto or urucum is an orange-yellow dye obtained from Bixa orellana seeds. It has been used as a natural dye in a variety of food products, drugs and cosmetics, and also in Brazilian cuisine as a condiment ('colorau'. Bixin, a carotenoid devoid of provitamin A activity, is the main pigment found in annatto. Some carotenoids (canthaxanthin, astaxanthin and ß-Apo-8'-carotenal are known to be potent inducers of CYP1A1, a property not shared by others (ß-carotene, lycopene and lutein. Little is known, however, about the CYP1A1-inducing properties of bixin and annatto. The present study was performed to determine the effects of an annatto extract (28% bixin and bixin (95% pure on rat liver monooxygenases. Adult female Wistar rats were treated by gavage with daily doses of annatto (250 mg/kg body weight, which contains approximately 70 mg bixin/kg body weight, bixin (250 mg/kg body weight or the vehicle only (corn oil, 3.75 g/kg body weight for 5 consecutive days, or were not treated (untreated control. The activities of aniline-4-hydroxylase (A4H, ethoxycoumarin-O-deethylase (ECOD, ethoxy- (EROD, methoxy- (MROD, pentoxy- (PROD and benzyloxy- (BROD resorufin-O-dealkylases were measured in liver microsomes. Annatto (250 mg/kg containing 70 mg bixin/kg induced EROD (3.8x, MROD (4.2x, BROD (3.3x and PROD (2.4x. Bixin (250 mg/kg was a weaker inducer of EROD (2.7x, MROD (2.3x and BROD (1.9x and did not alter PROD, A4H or ECOD activities. These results suggest that constituents of the extract other than bixin play an important role in the induction of CYP1A and CYP2B observed with annatto food colorings.

Crop Performance and Soil Properties in Two Artificially-Eroded Soils in North-Central Alberta

Energy Technology Data Exchange (ETDEWEB)

Izaurralde, R Cesar C.; Malhi, S. S.; Nyborg, M.; Solberg, E. D.; Quiroga Jakas, Maria C.

2006-09-01

Field experiments were conducted from 1991 to 1995 at Josephburg (Orthic Black Chernozem, Typic Cryoboroll) and Cooking Lake (Orthic Gray Luvisol, Typic Cryoboralf), Alberta, to determine impact of topsoil removal on selected soil properties, N-mineralization potential and crop yield, and effectiveness of various amendments for restoring the productivity of eroded soils. The simulated-erosion levels were established in the autumn of 1990 by removing 20 cm topsoil in 5-cm depth increments. The four amendments were: control, addition of 5 cm of topsoil, fertilizers to supply 100 kg N ha-1 and 20 kg P ha-1, and cattle manure at 75 Mg ha-1. Topsoil and manure were applied once in the autumn of 1990, while fertilizers were applied annually from 1991 to 1995. Available N and P, total C, N and P, and N-mineralization potential decreased, while bulk density increased with increasing depth of topsoil removal. Tiller number, plant height, spike density, thousand kernel weight, and leaf area index decreased with simulated erosion. Grain yield reductions due to simulated soil erosion were either linear or curvilinear functions of nutrient removal. Application of N and P fertilizers and manure improved grain yield and reduced the impact of yield loss due to erosion. Return of 5 cm of topsoil also increased grain yield, but to a lesser extent than manure or fertilizers. Grain yields were maximized when fertilizers were also applied to organic amendment treatments. In conclusion, the findings suggest the importance of integrated use of organic amendments and chemical fertilizers for best crop yields on severely-eroded soils.

Glyphosate and AMPA distribution in wind-eroded sediment derived from loess soil

NARCIS (Netherlands)

Martins Bento, Celia; Goossens, Dirk; Rezaei, Mahrooz; Riksen, M.J.P.M.; Mol, J.G.J.; Ritsema, C.J.; Geissen, V.

2017-01-01

Glyphosate is one of the most used herbicides in agricultural lands worldwide. Wind-eroded sediment and dust, as an environmental transport pathway of glyphosate and of its main metabolite aminomethylphosphonic acid (AMPA), can result in environmental- and human exposure far beyond the agricultural

High Ripples Reduction in DTC of Induction Motor by Using a New Reduced Switching Table

Science.gov (United States)

Mokhtari, Bachir; Benkhoris, Mohamed F.

2016-05-01

The direct torque and flux control (DTC) of electrical motors is characterized by ripples of torque and flux. Among the many solutions proposed to reduce them is to use modified switching tables which is very advantageous; because its implementation is easy and requires no additional cost compared to other solutions. This paper proposes a new reduced switching table (RST) to improve the DTC by reducing harmful ripples of torque and flux. This new switching table is smaller than the conventional one (CST) and depends principally at the flux error. This solution is studied by simulation under Matlab/Simulink and experimentally validated on a testbed with DSPACE1103. The results obtained of a DTC with RST applied to a three-phase induction motor (IM) show a good improvement and an effectiveness of proposed solution, the torque ripple decreases about 47% and 3% for the stator flux compared with a basic DTC.

Interrill Erodibility of P and C on conventially and organically farmed Devon soils

Science.gov (United States)

Kuhn, N. J.

2012-04-01

Soil erosion can have significant off-site effects on water quality and thus human and habitat health. Apart from sedimentation, the transfer of nutrients, both dissolved and particulate, is a major concern. The particulate transfer of nutrients from agricultural land can occur either by rill or interrill erosion. Rill erosion is non-selective and affects only a limited extent of agricultural land. Interrill processes such as crusting, splash and raindrop-impacted wash, on the other hand, act on all cropland and affect the quality of the water from all areas generating runoff. A significant amount of phosphorus (P) is contained in the surface soil layer transformed by interrill processes annually. In the EU, the P content of a crusted (2 mm) surface layer corresponds to 4 to 40 kg ha-1 of P on arable land (1.094 mil km2). Therefore, the role of interrill processes and erosion for regional nutrient cycling requires close attention. Interrill erosion is a complex phenomenon, involving the detachment, transport and deposition of soil particles by raindrop impacted flow. Resistance to interrill erosion varies between soils depending on their physical, chemical and mineralogical properties. In addition, significant changes in soil resistance to interrill erosion occur during storms as a result of changes in surface roughness, cohesion and particle size. As a consequence, erosion on interrill areas is selective, moving the most easily detached small and/or light soil particles which are often enriched in clay, P and organic C. Commonly, the risk of erosion associated with organically farmed soils is lower than those farmed in a conventional way. This is attributed to greater aggregate stability and thus greater infiltration and lower erodibility. Erosion of nutrients on organically farmed soils is therefore considered to be reduced by the same order of magnitude than the amount of eroded soil compared to conventionally farmed soils. However, the selective nature of

Blarina brevicauda as a biological monitor of polychlorinated biphenyls: evaluation of hepatic cytochrome P450 induction.

Science.gov (United States)

Russell, Julie S; Halbrook, Richard S; Woolf, Alan; French, John B; Melancon, Mark J

2004-08-01

We assessed the value of short-tailed shrews (Blarina brevicauda) as a possible biomonitor for polychlorinated biphenyl pollution through measurement of the induction of hepatic cytochrome P450 and associated enzyme activities. First, we checked the inducibility of four monooxygenases (benzyloxyresorufin-O-dealkylase [BROD], ethoxyresorufin-O-dealkylase [EROD], methoxyresorufin-O-dealkylase [MROD], and pentoxyresorufin-O-dealkylase [PROD]) by measuring the activity of these enzymes in hepatic microsomes prepared from shrews injected with beta-naphthoflavone (betaNF) or phenobarbital (PB), typical inducers of cytochrome P4501A (CYP1A) and CYP2B enzyme families, respectively. Enzyme activity was induced in shrews that received betaNF but not in shrews that received PB; PROD was not induced by either exposure. Later, shrews were exposed to a mixture of polychlorinated biphenyls (PCBs) (Aroclor 1242:1254, in 1:2 ratio) at 0.6, 9.6, and 150 ppm in food, for 31 d. Induction in these shrews was measured by specific enzyme activity (BROD, EROD, and MROD) in hepatic microsomes, by western blotting of solubilized microsomes against antibodies to CYP1A or CYP2B, and by duration of sodium pentobarbital-induced sleep. These three CYP enzymes were induced in shrews by PCBs at similar levels of exposure as in cotton rat (Sigmodon hispidus). Neither sleep time nor the amount of CYP2B family protein were affected by PCB exposure. Blarina brevicauda can be a useful biomonitor of PCBs that induce CYP1A, especially in habitats where they are the abundant small mammal.

CYP1A inhibition in fish gill filaments: A novel assay applied on pharmaceuticals and other chemicals

Energy Technology Data Exchange (ETDEWEB)

Beijer, Kristina; Abrahamson, Alexandra; Brunstroem, Bjoern [Department of Environmental Toxicology, Uppsala University, Norbyvaegen 18A, SE-752 36 Uppsala (Sweden); Brandt, Ingvar, E-mail: ingvar.brandt@ebc.uu.se [Department of Environmental Toxicology, Uppsala University, Norbyvaegen 18A, SE-752 36 Uppsala (Sweden)

2010-01-31

The gill filament 7-ethoxyresorufin O-deethylase (EROD) assay was originally developed as a biomarker for cytochrome P4501A (CYP1A) induction by Ah-receptor agonists in water. In this study, the assay was adapted to measure inhibition of CYP1A activity in fish gill filaments ex vivo. The experiments were carried out using gill arch filaments from {beta}-naphthoflavone ({beta}NF)-exposed three-spined stickleback (Gasterosteus aculeatus). Candidate CYP1A inhibitors were added to the assay buffer. Nine selected pharmaceuticals and five known or suspected CYP1A-modulating chemicals were examined with regard to their ability to reduce EROD activity in gill filaments. Ellipticine, a well characterized CYP1A inhibitor, was the most effective inhibitor of the compounds tested. At a concentration in the assay buffer of 1 {mu}M the antifungal azoles ketoconazole, miconazole and bitertanol, and the plant flavonoid acacetin reduced gill EROD activity by more than 50%, implying IC50 values below 1 {mu}M. These compounds have previously been shown to inhibit EROD activity in liver microsomes from fish and mammals at similar concentrations. The proton pump inhibitor omeprazole reduced the gill EROD activity by 39% at 10 {mu}M. It is concluded that the modified gill filament EROD assay is useful to screen for waterborne pollutants that inhibit catalytic CYP1A activity in fish gills.

CYP1A inhibition in fish gill filaments: A novel assay applied on pharmaceuticals and other chemicals

International Nuclear Information System (INIS)

Beijer, Kristina; Abrahamson, Alexandra; Brunstroem, Bjoern; Brandt, Ingvar

2010-01-01

The gill filament 7-ethoxyresorufin O-deethylase (EROD) assay was originally developed as a biomarker for cytochrome P4501A (CYP1A) induction by Ah-receptor agonists in water. In this study, the assay was adapted to measure inhibition of CYP1A activity in fish gill filaments ex vivo. The experiments were carried out using gill arch filaments from β-naphthoflavone (βNF)-exposed three-spined stickleback (Gasterosteus aculeatus). Candidate CYP1A inhibitors were added to the assay buffer. Nine selected pharmaceuticals and five known or suspected CYP1A-modulating chemicals were examined with regard to their ability to reduce EROD activity in gill filaments. Ellipticine, a well characterized CYP1A inhibitor, was the most effective inhibitor of the compounds tested. At a concentration in the assay buffer of 1 μM the antifungal azoles ketoconazole, miconazole and bitertanol, and the plant flavonoid acacetin reduced gill EROD activity by more than 50%, implying IC50 values below 1 μM. These compounds have previously been shown to inhibit EROD activity in liver microsomes from fish and mammals at similar concentrations. The proton pump inhibitor omeprazole reduced the gill EROD activity by 39% at 10 μM. It is concluded that the modified gill filament EROD assay is useful to screen for waterborne pollutants that inhibit catalytic CYP1A activity in fish gills.

Morphology of ductile metals eroded by a jet of spherical particles impinging at normal incidence

Science.gov (United States)

Veerabhadra Rao, P.; Young, S. G.; Buckley, D. H.

1983-01-01

Scanning electron microscopy and energy-dispersive X-ray spectroscopy are used, together with surface profile measurements, in the present morphological study of the erosion of an aluminum alloy and copper by the normal impact of spherical glass erodent particles. The morphology of the damage pattern is a manifestation of the flow pattern of erodent particles, and yields insight into the mechanisms that may be active at different stages of erosion. The simultaneous appearance of radial cracks and concentric rings is reported, together with wave crests which contain an accumulation of metallic flakes. A preliminary analysis is advanced to explain the formation of the various damage patterns observed.

ASSESSMENT SPATIAL VARIABILITY OF SOIL ERODIBILITY BY USING OF GEOSTATISTIC AND GIS (Case study MEHR watershed of SABZEVAR

Directory of Open Access Journals (Sweden)

Ayoubi, S.A

2005-05-01

Full Text Available Soil erodibility is one of the key factors on some sediment and soil erosion models such as USLE, MUSLE, RUSLE, AUSLE (USLE modified in LS factor and MMF and represents like K factor and is function of particle distribution, organic mater, soil structure and ermeability. Traditional methods do not take spatial variability and estimate precision of variables in to consideration and amount of them are constant across the whole of soil series .This study was performed to assess spatial variability of soil erodibility and its relevant variables at MEHR watershed from Khorasan province, in northern Iran. Interested network was designed by 110 samples like nested- systematic with distance about 50, 100, 250 and 500 meter across the study area by preparing point map at GIS. Sampling points were identified in field by an Global Positioning system. Soil sampling was done at depth of 0-5cm of ground surface and permeability was studied at depth of 5-30 cm. Some soil properties such as particle distribution and organic mater were measured at laboratory. Particle size distribution was determined by Hydrometer method and Organic matter was measured by wet oxidation approach. Then spatial analysis was done. Variography analysis on soil attributes according to soil erodibility, showed that Gaussian, exponential and spherical models were the most models to predict spatial variability of soil parameters. The range of spatial dependencies was changed from 320 to 3200 m. Soil attribute maps prepared by kriging technique using models parameters. Then soil attributes were composed by Wischmeier (1978 formula in Illwis media to calculate K factor. Amount of soil erodibility changed from 0.13 to 0.91 that it's maximum and minimum was identified in east and southwest of studiedarea. Soil spatial variability pattern, is similar to silt pattern due to high effect of silt on soil rodibility, Also that is partially confirmed with geology map, indicated which soil

[Soil anti-erodibility of abandoned lands during different succession stages of plant community in hilly-gullied region of the Loess Plateau: Take Fangta small watershed as an example].

Science.gov (United States)

Yan, Fang-chen; Jiao, Ju-ying; Cao, Bin-ting; Yu, Wei-jie; Wei, Yan-hong; Kou, Meng; Hu, Shu

2016-01-01

Field survey and laboratory experiment were conducted to study the soil anti-erodibility of abandoned croplands during different vegetation succession stages in hilly-gullied region of the Loess Plateau, based on the analysis of soil particle composition, size distribution and group characteristics, soil aggregate fractal dimensions and stability. The results showed that in the earlier stages of succession from annual to perennial herbs in abandoned croplands, soil size distribution changed a little bit, the fractal dimension of soil particle increased, soil structure improved, fractal dimension and damage percent of soil aggregate structure decreased, soil stability increased, thus soil anti-erodibility increased. Therefore, natural restoration of vegetation is of great significance to improve the soil structure, increase soil erosion resistance, reduce soil erosion and promote sustainable development of regional ecological environment.

Determination of interrill soil erodibility coefficient based on Fuzzy and Fuzzy-Genetic Systems

Directory of Open Access Journals (Sweden)

Habib Palizvan Zand

2017-02-01

Full Text Available Introduction: Although the fuzzy logic science has been used successfully in various sudies of hydrology and soil erosion, but in literature review no article was found about its performance for estimating of interrill erodibility. On the other hand, studies indicate that genetic algorithm techniques can be used in fuzzy models and finding the appropriate membership functions for linguistic variables and fuzzy rules. So this study was conducted to develop the fuzzy and fuzzy–genetics models and investigation of their performance in the estimation of soil interrill erodibility factor (Ki. Materials and Methods: For this reason 36 soil samples with different physical and chemical properties were collected from west of Azerbaijan province . soilsamples were also taken from the Ap or A horizon of each soil profile. The samples were air-dried , sieved and Some soil characteristics such as soil texture, organic matter (OM, cation exchange capacity (CEC, sodium adsorption ratio (SAR, EC and pH were determined by the standard laboratory methods. Aggregates size distributions (ASD were determined by the wet-sieving method and fractal dimension of soil aggregates (Dn was also calculated. In order to determination of soil interrill erodibility, the flume experiment performed by packing soil a depth of 0.09-m in 0.5 × 1.0 m. soil was saturated from the base and adjusted to 9% slope and was subjected to at least 90 min rainfall . Rainfall intensity treatments were 20, 37 and 47 mm h-1. During each rainfall event, runoff was collected manually in different time intervals, being less than 60 s at the beginning, up to 15 min near the end of the test. At the end of the experiment, the volumes of runoff samples and the mass of sediment load at each time interval were measured. Finally interrill erodibility values were calculated using Kinnell (11 Equation. Then by statistical analyses Dn and sand percent of the soils were selected as input variables and Ki as

Fluvial organic carbon flux from an eroding peatland catchment, southern Pennines, UK

Directory of Open Access Journals (Sweden)

R. R. Pawson

2008-03-01

Full Text Available This study investigates for the first time the relative importance of dissolved organic carbon (DOC and particulate organic carbon (POC in the fluvial carbon flux from an actively eroding peatland catchment in the southern Pennines, UK. Event scale variability in DOC and POC was examined and the annual flux of fluvial organic carbon was estimated for the catchment. At the event scale, both DOC and POC were found to increase with discharge, with event based POC export accounting for 95% of flux in only 8% of the time. On an annual cycle, exports of 35.14 t organic carbon (OC are estimated from the catchment, which represents an areal value of 92.47 g C m⁻² a⁻¹. POC was the most significant form of organic carbon export, accounting for 80% of the estimated flux. This suggests that more research is required on both the fate of POC and the rates of POC export in eroding peatland catchments.

Harlequin duck capture and EROD activity data from Prince William Sound, Alaska, 2011, 2013, 2014

Data.gov (United States)

Department of the Interior — This data set includes capture information and ethoxyresorufin­O­deethylase (EROD) activity results for harlequin ducks sampled during March 2011, 2013, and 2014 in...

Influence of bleaching agents on surface roughness of sound or eroded dental enamel specimens.

Science.gov (United States)

Azrak, Birgül; Callaway, Angelika; Kurth, Petra; Willershausen, Brita

2010-12-01

The aim of the present in vitro study was to assess the effect of bleaching agents on eroded and sound enamel specimens. Enamel specimens prepared from human permanent anterior teeth were incubated with different bleaching agents containing active ingredients as 7.5 or 13.5% hydrogen peroxide or 35% carbamide peroxide, ranging in pH from 4.9 to 10.8. The effect of the tooth whitening agents on surface roughness was tested for sound enamel surfaces as well as for eroded enamel specimens. To provoke erosive damage, the enamel specimens were incubated for 10 hours with apple juice (pH = 3.4). Afterwards, pretreated and untreated dental slices were incubated with one of the bleaching agents for 10 hours. The surface roughness (R(a)) of all enamel specimens (N = 80) was measured using an optical profilometric device. A descriptive statistical analysis of the R(a) values was performed. The study demonstrated that exposure to an acidic bleaching agent (pH = 4.9) resulted in a higher surface roughness (p = 0.043) than treatment with a high peroxide concentration (pH = 6.15). If the enamel surface was previously exposed to erosive beverages, subsequent bleaching may enhance damage to the dental hard tissue. Bleaching agents with a high concentration of peroxide or an acidic pH can influence the surface roughness of sound or eroded enamel. © 2010, COPYRIGHT THE AUTHORS. JOURNAL COMPILATION © 2010, WILEY PERIODICALS, INC.

Application of forgetful analgesia induction in induction period in patients with obstructive jaundice

Directory of Open Access Journals (Sweden)

Wei DU

2014-03-01

Full Text Available Objective　To observe the effect of forgetful analgesia induction and tracheal intubation on the hemodynamic changes in induction period in patients with obstructive jaundice, and explore a safe method for anesthesia induction and tracheal intubation. Methods　Sixty patients with obstructive jaundice undergoing elective abdominal operation in General Hospital of PLA from February, 2013 to August, 2013 were involved in the present study. Participants included 36 male and 24 female patients, aging 19-65 years (mean 42±5 years, weighing 47-73 kg (mean 54±6 kg, with ASA Ⅰ-Ⅱ. These 60 patients were randomly divided into forgetful analgesia induction-tracheal intubation group (group A, n=30 and rapid induction-tracheal intubation group (group B, n=30. The heart rate (HR, mean arterial pressure (MAP, pulse oxygen saturation (SpO2 at the time point of before induction (T0, before intubation (T1, at the moment of intubation (T2 and 3 min after intubation (T3 were determined in both groups. Administration times of ephedrine hydrochloride and atropine was recorded in both groups. Results　There was no significant difference in HR, MAP, SpO2 before and after induction in group A. In the patients of group B, the HR increased and MAP decreased after induction compared with those before induction (P<0.05, and the change of SpO2 was not significant. Ephedrine hydrochloride and atropine were administrated in both groups, and the cases and times of ephedrine hydrochloride administration were more in group B than in group A (P<0.05. Conclusion　The forgetful analgesia induction-tracheal intubation could effectively control the stress response and reduce the fluctuation in hemodynamics during induction of anesthesia in patients with obstructive jaundice. DOI: 10.11855/j.issn.0577-7402.2014.02.15

Testing the effect of a microbial-based soil amendment on aggregate stability and erodibility

DEFF Research Database (Denmark)

Malozo, Mponda; Iversen, Bo Vangsø; Heckrath, Goswin Johann

to the rainfall-runoff experiment where the microbial-based product had a clear effect on soil erodibility. In relation to measurement of aggregate stability as well as clay dispersion, the picture was less clear. Especially for the sandy Tanzania soil with a low content of organic matter, a clear effect was seen...... aggregate stability and erodibility. Two commercial products, gypsum and a microbial-based solution were used for the experiment and were tested on two Danish sandy loamy soils as well on a sandy soil from Tanzania. The carrier of the microbial-based product, a glycerol solution, was tested as well....... In the laboratory, soils were treated with the soil amendments in a two-step procedure at controlled water contents following aerobic incubation in closed containers. Water-aggregate stability and clay dispersion were measured on soil aggregates less than 8 mm in diameter. Aggregate stability was measured...

How Welfare Regimes Generate and Erode Social Capital

DEFF Research Database (Denmark)

Larsen, Christian Albrekt

2007-01-01

in the USA and other liberal welfare regimes, while social capital is stable in the so-called social democratic and conservative welfare regimes. The second puzzle is why the group of social democratic regimes have extremely high levels of social trust. It is argued that both puzzles have to do......Comparative studies of social capital, operationalised as social trust between citizens, have revealed two major puzzles. The first puzzle has to do with the decline in social trust in the USA, which fuelled considerable debate about social capital. The question is why social capital erodes...... with the presence or absence of a poor and culturally distinct underclass. The social democratic welfare regimes hinder – while the liberal welfare regime generate – such underclass phenomena....

Eroding market stability by proliferation of financial instruments

Science.gov (United States)

Caccioli, F.; Marsili, M.; Vivo, P.

2009-10-01

We contrast Arbitrage Pricing Theory (APT), the theoretical basis for the development of financial instruments, with a dynamical picture of an interacting market, in a simple setting. The proliferation of financial instruments apparently provides more means for risk diversification, making the market more efficient and complete. In the simple market of interacting traders discussed here, the proliferation of financial instruments erodes systemic stability and it drives the market to a critical state characterized by large susceptibility, strong fluctuations and enhanced correlations among risks. This suggests that the hypothesis of APT may not be compatible with a stable market dynamics. In this perspective, market stability acquires the properties of a common good, which suggests that appropriate measures should be introduced in derivative markets, to preserve stability. in here

Introduction of a methoxymethyl side chain into p-phenylenediamine attenuates its sensitizing potency and reduces the risk of allergy induction

Energy Technology Data Exchange (ETDEWEB)

Goebel, Carsten, E-mail: goebel.c.1@pg.com [The Procter and Gamble Co., Central Product Safety and Communications, Darmstadt (Germany); Troutman, John [The Procter and Gamble Co., Central Product Safety, Cincinnati, OH (United States); Hennen, Jenny [Dept. of Environmental Toxicology, Trier University, Trier (Germany); Rothe, Helga; Schlatter, Harald [The Procter and Gamble Co., Central Product Safety and Communications, Darmstadt (Germany); Gerberick, G. Frank [The Procter and Gamble Co., Central Product Safety, Cincinnati, OH (United States); Blömeke, Brunhilde [Dept. of Environmental Toxicology, Trier University, Trier (Germany)

2014-02-01

The strong sensitizing potencies of the most important primary intermediates of oxidative hair dyes, p-phenylenediamine (PPD) and p-toluylenediamine (PTD, i.e. 2-methyl-PPD) are well established. They are considered as the key sensitizers in hair dye allergic contact dermatitis. While modification of their molecular structure is expected to alter their sensitizing properties, it may also impair their color performance. With introduction of a methoxymethyl side chain we found the primary intermediate 2-methoxymethyl-p-phenylenediamine (ME-PPD) with excellent hair coloring performance but significantly reduced sensitizing properties compared to PPD and PTD: In vitro, ME-PPD showed an attenuated innate immune response when analyzed for its protein reactivity and dendritic cell activation potential. In vivo, the effective concentration of ME-PPD necessary to induce an immune response 3-fold above vehicle control (EC3 value) in the local lymph node assay (LLNA) was 4.3%, indicating a moderate skin sensitizing potency compared to values of 0.1 and 0.17% for PPD and PTD, respectively. Finally, assessing the skin sensitizing potency of ME-PPD under consumer hair dye usage conditions through a quantitative risk assessment (QRA) indicated an allergy induction risk negligible compared to PPD or PTD. - Highlights: • Methoxymethyl side chain in p-phenylenediamine reduces its strong skin sensitizing properties. • Reduced protein reactivity and dendritic cell activation. • Reduced skin sensitizing potency in local lymph node assay (LLNA). • Negligible allergy induction risk under hair dye usage conditions.

Introduction of a methoxymethyl side chain into p-phenylenediamine attenuates its sensitizing potency and reduces the risk of allergy induction

International Nuclear Information System (INIS)

Goebel, Carsten; Troutman, John; Hennen, Jenny; Rothe, Helga; Schlatter, Harald; Gerberick, G. Frank; Blömeke, Brunhilde

2014-01-01

The strong sensitizing potencies of the most important primary intermediates of oxidative hair dyes, p-phenylenediamine (PPD) and p-toluylenediamine (PTD, i.e. 2-methyl-PPD) are well established. They are considered as the key sensitizers in hair dye allergic contact dermatitis. While modification of their molecular structure is expected to alter their sensitizing properties, it may also impair their color performance. With introduction of a methoxymethyl side chain we found the primary intermediate 2-methoxymethyl-p-phenylenediamine (ME-PPD) with excellent hair coloring performance but significantly reduced sensitizing properties compared to PPD and PTD: In vitro, ME-PPD showed an attenuated innate immune response when analyzed for its protein reactivity and dendritic cell activation potential. In vivo, the effective concentration of ME-PPD necessary to induce an immune response 3-fold above vehicle control (EC3 value) in the local lymph node assay (LLNA) was 4.3%, indicating a moderate skin sensitizing potency compared to values of 0.1 and 0.17% for PPD and PTD, respectively. Finally, assessing the skin sensitizing potency of ME-PPD under consumer hair dye usage conditions through a quantitative risk assessment (QRA) indicated an allergy induction risk negligible compared to PPD or PTD. - Highlights: • Methoxymethyl side chain in p-phenylenediamine reduces its strong skin sensitizing properties. • Reduced protein reactivity and dendritic cell activation. • Reduced skin sensitizing potency in local lymph node assay (LLNA). • Negligible allergy induction risk under hair dye usage conditions

Erodibility of calcareous soils as influenced by land use and intrinsic soil properties in a semiarid region of central Iran.

Science.gov (United States)

Ayoubi, Shamsollah; Mokhtari, Javad; Mosaddeghi, Mohammad Reza; Zeraatpisheh, Mojtaba

2018-03-06

The most important properties affecting the soil loss and runoff were investigated, and the effects of land use on the soil properties, together with the erodibility indices in a semiarid zone, central Iran, were evaluated. The locations of 100 positions were acquired by cLHS and 0-5-cm surface soil layer samples were used for laboratory analyses from the Borujen Region, Chaharmahal-Va-Bakhtiari Province, central Iran. To measure in situ runoff and soil erodibility of three different land uses comprising dryland, irrigated farming, and rangeland, a portable rainfall simulator was used. The results showed that the high variations (coefficient of variation, CV) were obtained for electrical conductivity (EC), mean weight diameter (MWD), soil organic carbon (SOC), and soil erodibility indices including runoff volume, soil loss, and sediment concentration (CV ~ 43.6-77.4%). Soil erodibility indices showed positive and significant correlations with bulk density and negative correlations with SOC, MWD, clay content, and soil shear strength in the area under investigation. The values of runoff in the dryland, irrigated farming, and rangeland were found 1.5, 28.9, and 58.7 cm 3 ; soil loss in the dryland, irrigated farming, and rangeland were observed 0.25, 2.96, and 76.8 g; and the amount of sediment concentration in the dryland, irrigated farming, and rangeland were found 0.01, 0.11, and 0.15 g cm -3 . It is suggested that further investigations should be carried out on soil erodibility and the potential of sediment yield in various land uses with varying topography and soil properties in semiarid regions of Iran facing the high risk of soil loss.

EROD activity and stable isotopes in seabirds to disentangle marine food web contamination after the Prestige oil spill

Energy Technology Data Exchange (ETDEWEB)

Velando, Alberto, E-mail: avelando@uvigo.e [Departamento de Ecoloxia e Bioloxia Animal, Facultade de Ciencias, Universidade de Vigo, Campus As Lagoas, 36310 Vigo (Spain); Munilla, Ignacio [Departamento de Botanica, Facultade de Farmacia, Universidade de Santiago de Compostela, Santiago de Compostela (Spain); Lopez-Alonso, Marta [Departamento de Patoloxia Animal, Facultade de Veterinaria, Universidade de Santiago de Compostela, Lugo (Spain); Freire, Juan [Grupo de Recursos Marinos y Pesquerias Universidade da Coruna, A Coruna (Spain); Perez, Cristobal [Departamento de Ecoloxia e Bioloxia Animal, Facultade de Ciencias, Universidade de Vigo, Campus As Lagoas, 36310 Vigo (Spain)

2010-05-15

In this study, we measured via surgical sampling hepatic EROD activity in yellow-legged gulls from oiled and unoiled colonies, 17 months after the Prestige oil spill. We also analyzed stable isotope composition in feathers of the biopsied gulls, in an attempt to monitor oil incorporation into marine food web. We found that yellow-legged gulls in oiled colonies were being exposed to remnant oil as shown by hepatic EROD activity levels. EROD activity was related to feeding habits of individual gulls with apparent consequences on delayed lethality. Capture-recapture analysis of biopsied gulls suggests that the surgery technique did not affect gull survival, giving support to this technique as a monitoring tool for oil exposure assessment. Our study highlights the combination of different veterinary, toxicological and ecological methodologies as a useful approach for the monitoring of exposure to remnant oil after a large oil spill. - Two years after Prestige oil spill, seabirds were exposed to remnant oil related to their feeding habits with consequences on delayed lethality.

EROD activity and stable isotopes in seabirds to disentangle marine food web contamination after the Prestige oil spill

International Nuclear Information System (INIS)

Velando, Alberto; Munilla, Ignacio; Lopez-Alonso, Marta; Freire, Juan; Perez, Cristobal

2010-01-01

In this study, we measured via surgical sampling hepatic EROD activity in yellow-legged gulls from oiled and unoiled colonies, 17 months after the Prestige oil spill. We also analyzed stable isotope composition in feathers of the biopsied gulls, in an attempt to monitor oil incorporation into marine food web. We found that yellow-legged gulls in oiled colonies were being exposed to remnant oil as shown by hepatic EROD activity levels. EROD activity was related to feeding habits of individual gulls with apparent consequences on delayed lethality. Capture-recapture analysis of biopsied gulls suggests that the surgery technique did not affect gull survival, giving support to this technique as a monitoring tool for oil exposure assessment. Our study highlights the combination of different veterinary, toxicological and ecological methodologies as a useful approach for the monitoring of exposure to remnant oil after a large oil spill. - Two years after Prestige oil spill, seabirds were exposed to remnant oil related to their feeding habits with consequences on delayed lethality.

Erodibility of surface-mine spoil banks in southeastern Ohio : an approximation

Energy Technology Data Exchange (ETDEWEB)

McKenzie, C D; Studlick, J R.J.

1979-07-01

Measurements of accumulated sediment in inter-bank basins of unreclaimed strip mines determined the average annual site loss from unvegetated, 18-year-old spoil banks. Assuming that the universal soil loss equation (USLE) can be used to estimate sediment yield from strip mine slopes, the topographic factor in the USLE was determined in 2 ways, and values for erodibility well calculated. The technique is applicable to unreclaimed mines where inter-bank basins trap all slope-derived sediment.

Role of brain cytochrome P450 mono-oxygenases in bilirubin oxidation-specific induction and activity.

Science.gov (United States)

Gambaro, Sabrina E; Robert, Maria C; Tiribelli, Claudio; Gazzin, Silvia

2016-02-01

In the Crigler-Najjar type I syndrome, the genetic absence of efficient hepatic glucuronidation of unconjugated bilirubin (UCB) by the uridine 5'-diphospho-glucuronosyltransferase1A1 (UGT1A1) enzyme produces the rise of UCB level in blood. Its entry to central nervous system could generate toxicity and neurological damage, and even death. In the past years, a compensatory mechanism to liver glucuronidation has been indicated in the hepatic cytochromes P450 enzymes (Cyps) which are able to oxidize bilirubin. Cyps are expressed also in the central nervous system, the target of bilirubin toxicity, thus making them theoretically important to confer a protective activity toward bilirubin accumulation and neurotoxicity. We therefore investigated the functional induction (mRNA, EROD/MROD) and the ability to oxidize bilirubin of Cyp1A1, 1A2, and 2A3 in primary astrocytes cultures obtained from two rat brain region (cortex: Cx and cerebellum: Cll). We observed that Cyp1A1 was the Cyp isoform more easily induced by beta-naphtoflavone (βNF) in both Cx and Cll astrocytes, but oxidized bilirubin only after uncoupling by 3, 4,3',4'-tetrachlorobiphenyl (TCB). On the contrary, Cyp1A2 was the most active Cyp in bilirubin clearance without uncoupling, but its induction was confined only in Cx cells. Brain Cyp2A3 was not inducible. In conclusion, the exposure of astrocytes to βNF plus TCB significantly enhanced Cyp1A1 mediating bilirubin clearance, improving cell viability in both regions. These results may be a relevant groundwork for the manipulation of brain Cyps as a therapeutic approach in reducing bilirubin-induced neurological damage.

Photorefractive keratectomy (PRK) at 193 nm using an erodible mask: new developments and clinical progress

Science.gov (United States)

Gordon, Michael; Seiler, Theo; Carey, Joseph P.; Friedman, Marc D.; Johnsson, N. M. F.; King, Michael C.; Muller, David F.

1993-06-01

This paper reports on our progress using an erodible mask to perform photorefractive keratectomy (PRK) for the correction of myopic astigmatism. We describe modifications to the mask, the mask eye cup and the surgical microscope aimed at simplifying the procedure and improving the ergonomics of the hardware. We report the clinical results of the post-op exam for 20 patients who have undergone PRK for myopic astigmatism under a Phase IIA study. The results compare favorably with an earlier Phase IIA study for performing PRK with a computer-controlled iris. Most important, the clinical data show the absence of any significant corneal haze and no significant decrease in spectacle corrected visual acuity. Although more long term follow-up is needed, the preliminary results support the safety and effectiveness of using an erodible mask to perform PRK for myopic astigmatism.

A PEDOTRANSFER FUNCTION FOR ESTIMATING THE SOIL ERODIBILITY FACTOR IN SICILY

Directory of Open Access Journals (Sweden)

Vincenzo Bagarello

2009-09-01

Full Text Available The soil erodibility factor, K, of the Universal Soil Loss Equation (USLE is a simple descriptor of the soil susceptibility to rill and interrill erosion. The original procedure for determining K needs a knowledge of soil particle size distribution (PSD, soil organic matter, OM, content, and soil structure and permeability characteristics. However, OM data are often missing and soil structure and permeability are not easily evaluated in regional analyses. The objective of this investigation was to develop a pedotransfer function (PTF for estimating the K factor of the USLE in Sicily (south Italy using only soil textural data. The nomograph soil erodibility factor and its associated first approximation, K’, were determined at 471 sampling points distributed throughout the island of Sicily. Two existing relationships for estimating K on the basis of the measured geometric mean particle diameter were initially tested. Then, two alternative PTFs for estimating K’ and K, respectively, on the basis of the measured PSD were derived. Testing analysis showed that the K estimate by the proposed PTF (eq.11, which was characterized by a Nash-Suttcliffe efficiency index, NSEI, varying between 0.68 and 0.76, depending on the considered data set, was appreciably more accurate than the one obtained by other existing equations, yielding NSEI values varying between 0.21 and 0.32.

Effect of inter-tissue inductive coupling on multi-frequency imaging of intracranial hemorrhage by magnetic induction tomography

Science.gov (United States)

Xiao, Zhili; Tan, Chao; Dong, Feng

2017-08-01

Magnetic induction tomography (MIT) is a promising technique for continuous monitoring of intracranial hemorrhage due to its contactless nature, low cost and capacity to penetrate the high-resistivity skull. The inter-tissue inductive coupling increases with frequency, which may lead to errors in multi-frequency imaging at high frequency. The effect of inter-tissue inductive coupling was investigated to improve the multi-frequency imaging of hemorrhage. An analytical model of inter-tissue inductive coupling based on the equivalent circuit was established. A set of new multi-frequency decomposition equations separating the phase shift of hemorrhage from other brain tissues was derived by employing the coupling information to improve the multi-frequency imaging of intracranial hemorrhage. The decomposition error and imaging error are both decreased after considering the inter-tissue inductive coupling information. The study reveals that the introduction of inter-tissue inductive coupling can reduce the errors of multi-frequency imaging, promoting the development of intracranial hemorrhage monitoring by multi-frequency MIT.

Turbidity current hydraulics and sediment deposition in erodible sinuous channels: Laboratory experiments and numerical simulations

NARCIS (Netherlands)

Janocko, M.; Cartigny, M.J.B.; Nemec, W.; Hansen, E.W.M.

2013-01-01

This study explores the relationship between the hydraulics of turbidity currents in erodible sinuous channels and the resulting intra-channel sediment depocentres (channel bars). Four factors are considered to exert critical control on sedimentation in sinuous submarine channels: (1) the

Sensitivity Analysis of the USLE Soil Erodibility Factor to Its Determining Parameters

Science.gov (United States)

Mitova, Milena; Rousseva, Svetla

2014-05-01

Soil erosion is recognized as one of the most serious soil threats worldwide. Soil erosion prediction is the first step in soil conservation planning. The Universal Soil Loss Equation (USLE) is one of the most widely used models for soil erosion predictions. One of the five USLE predictors is the soil erodibility factor (K-factor), which evaluates the impact of soil characteristics on soil erosion rates. Soil erodibility nomograph defines K-factor depending on soil characteristics, such as: particle size distribution (fractions finer that 0.002 mm and from 0.1 to 0.002 mm), organic matter content, soil structure and soil profile water permeability. Identifying the soil characteristics, which mostly influence the K-factor would give an opportunity to control the soil loss through erosion by controlling the parameters, which reduce the K-factor value. The aim of the report is to present the results of analysis of the relative weight of these soil characteristics in the K-factor values. The relative impact of the soil characteristics on K-factor was studied through a series of statistical analyses of data from the geographic database for soil erosion risk assessments in Bulgaria. Degree of correlation between K-factor values and the parameters that determine it was studied by correlation analysis. The sensitivity of the K-factor was determined by studying the variance of each parameter within the range between minimum and maximum possible values considering average value of the other factors. Normalizing transformation of data sets was applied because of the different dimensions and the orders of variation of the values of the various parameters. The results show that the content of particles finer than 0.002 mm has the most significant relative impact on the soil erodibility, followed by the content of particles with size from 0.1 mm to 0.002 mm, the class of the water permeability of the soil profile, the content of organic matter and the aggregation class. The

Analysis of eroded bovine teeth through laser speckle imaging

Science.gov (United States)

Koshoji, Nelson H.; Bussadori, Sandra K.; Bortoletto, Carolina C.; Oliveira, Marcelo T.; Prates, Renato A.; Deana, Alessandro M.

2015-02-01

Dental erosion is a non-carious lesion that causes progressive tooth wear of structure through chemical processes that do not involve bacterial action. Its origin is related to eating habits or systemic diseases involving tooth contact with substances that pose a very low pH. This work demonstrates a new methodology to quantify the erosion by coherent light scattering of tooth surface. This technique shows a correlation between acid etch duration and laser speckle contrast map (LASCA). The experimental groups presented a relative contrast between eroded and sound tissue of 17.8(45)%, 23.4 (68)% 39.2 (40)% and 44.3 (30)%, for 10 min, 20 min, 30 min and 40 min of acid etching, respectively.

Use of oxidative and reducing vapor generation for reducing the detection limits of iodine in biological samples by inductively coupled plasma atomic emission spectrometry

International Nuclear Information System (INIS)

Vtorushina, Eh.A.; Saprykin, A.I.; Knapp, G.

2009-01-01

Procedures of microwave combustion in an oxygen flow and microwave acid decomposition of biological samples were optimized for the subsequent determination of iodine. A new method was proposed for the generation of molecular iodine from periodate iona using hydrogen peroxide as a reductant. Procedures were developed for determining iodine in biological samples by inductively coupled plasma atomic emission spectrometry (ICP-AES) using oxidative and reducing vapor generation; these allowed the detection limit for iodine to be lowered by 3-4 orders of magnitude. The developed procedures were used to analyze certified reference materials of milk (Skim Milk Powder BCR 150) and seaweed (Sea Lettuce BCR 279) and a Supradyn vitamin complex

Predictive model for local scour downstream of hydrokinetic turbines in erodible channels

Science.gov (United States)

Musa, Mirko; Heisel, Michael; Guala, Michele

2018-02-01

A modeling framework is derived to predict the scour induced by marine hydrokinetic turbines installed on fluvial or tidal erodible bed surfaces. Following recent advances in bridge scour formulation, the phenomenological theory of turbulence is applied to describe the flow structures that dictate the equilibrium scour depth condition at the turbine base. Using scaling arguments, we link the turbine operating conditions to the flow structures and scour depth through the drag force exerted by the device on the flow. The resulting theoretical model predicts scour depth using dimensionless parameters and considers two potential scenarios depending on the proximity of the turbine rotor to the erodible bed. The model is validated at the laboratory scale with experimental data comprising the two sediment mobility regimes (clear water and live bed), different turbine configurations, hydraulic settings, bed material compositions, and migrating bedform types. The present work provides future developers of flow energy conversion technologies with a physics-based predictive formula for local scour depth beneficial to feasibility studies and anchoring system design. A potential prototype-scale deployment in a large sandy river is also considered with our model to quantify how the expected scour depth varies as a function of the flow discharge and rotor diameter.

Retrofitting adjustable speed drives for large induction motors

International Nuclear Information System (INIS)

Wuestefeld, M.R.; Merriam, C.H.; Porter, N.S.

2004-01-01

Adjustable speed drives (ASDs) are used in many power plants to control process flow by varying the speed of synchronous and induction motors. In applications where the flow requirements vary significantly, ASDs reduce energy and maintenance requirements when compared with drag valves, dampers or other methods to control flow. Until recently, high horsepower ASDs were not available for induction motors. However, advances in power electronics technology have demonstrated the reliability and cost effectiveness of ASDs for large horsepower induction motors. Emphasis on reducing operation and maintenance costs and increasing the capacity factor of nuclear power plants has led some utilities to consider replacing flow control devices in systems powered by large induction motors with ASDs. ASDs provide a high degree of reliability and significant energy savings in situations where full flow operation is not needed for a substantial part of the time. This paper describes the basic adjustable speed drive technologies available for large induction motor applications, ASD operating experience and retrofitting ASDs to replace the existing GE Boiling Water Reactor recirculation flow control system

The concentrations of heavy metals and the incidence of micronucleated erythrocytes and liver EROD activity in two edible-fish from the Paraíba do Sul river basin in Brazil | Concentração de metais pesados e incidência de eritrócitos micronucleados e atividade de EROD hepática em duas espécies de peixes comestíveis na bacia do Rio Paraíba do Sul, Brasil

Directory of Open Access Journals (Sweden)

Thiago Estevam Martins Parente

2015-02-01

Full Text Available The Paraíba do Sul river (PSR basin crosses one of the most populated and industrialized regions of Brazil and receives effluent from the metallurgic, paper mill and agricultural industries. PSR water has multiple uses, including being a supply of potable water and riverine populations which consume some species of its fish. In the present study, we investigated the responses of two biomarkers of aquatic pollution, EROD activity in the liver and micronuclei frequency in peripheral blood, as well as the concentrations of seven heavy metals in the muscle tissue of two species of fish native to the PSR: Geophagus brasiliensis and Hypostomus sp. Sampling was performed in both the wet and dry seasons of 2003, with a total of 339 fish collected from 16 sites along the PSR basin. Fish collected at Levy Gasparian, Barra Mansa and Três Rios both had higher EROD activity and micronuclei frequency. The results also suggested a moderate induction of EROD activity in fish collected from S.L. Paraitinga and Sapucaia. Micronuclei frequency was elevated in fish from S.J. Campos, Além Paraíba, Campos and S.J. Barra. In all cases, heavy metal concentrations did not exceed the maximum considered safe for fish meat consumption. -------------------------------------------------------------------------------------------- A bacia do rio Paraíba do Sul (PSR atravessa uma das regiões mais povoadas e industrializadas do Brasil, recebendo efluentes de indústrias metalúrgicas, de papel e celulose e agrícolas. Os usos das águas do PSR são múltiplos, incluem o fornecimento de água potável, e as populações ribeirinhas consomem algumas de suas espécies de peixes. No presente trabalho foram investigadas as respostas de dois biomarcadores à poluição, a atividade hepática de EROD e a freqüência de micronúcleo em sangue periférico, e medidos os níveis de sete metais pesados no músculo de duas espécies de peixes nativas do PSR, Geophagus brasiliensis and

Influence of biochar and terra preta substrates on wettability and erodibility of soils

Science.gov (United States)

Smetanova, A.; Dotterweich, M.; Diehl, D.; Ulrich, U.; Fohrer, N.

2012-04-01

Biochar (BC) and terra preta substrates (TPS) have recently been promoted as soil amendments suitable for soil stabilization, soil amelioration and long-term carbon sequestration. BC is a carbon-enriched substance produced by thermal decomposition of organic material. TPS is composed of liquid and solid organic matter, including BC, altered by acid-lactic fermentation. Their effect on wettability, soil erodibility and nutrient discharge through overland flow was studied by laboratory experiments. At water contents between 0 and 100% BC is water repellent, while TPS changes from a wettable into a repellent state. The 5 and 10 vol % mixtures of BC and 10 and 20 vol% mixtures of TPS with sand remain mainly wettable during drying but repellency maxima are shifted to higher water contents with respect to pure sand and are mainly of subcritical nature. The runoff response was dominated by infiltration properties of the substrates rather than their wettability.Only one mixtures (20% TPS) produced more runoff than sandy-loamy soil on a 15% slope at an intensity of 25 mm•h-1. The 10% BC decreased runoff by up to 40%. At higher rainfall intensities (45 and 55 mm•h-1) the 10% TPS7 was up to 35% less erodible than 10% BC. Despite the TPS containing more nutrients, nutrient discharge varied between types of nutrients, slopes, rainfall intensities and mixtures. The application of a 1 cm layer onto the soil surface instead of 10% mixtures is not recommended due to high nutrient concentrations in the runoff and the wettability of pure substrates. The usage of 10% BC in lowland areas with low frequency and low-intensity precipitation and 10% TPS7 in areas with higher rainfall intensities appears to be appropriate and commendable according to current results. However, together with reversibility of repellency, it needs to undergo further examination in the field under different environmental and land use conditions Key words: biochar, terra preta substrate, wettability

A statistical model for horizontal mass flux of erodible soil

International Nuclear Information System (INIS)

Babiker, A.G.A.G.; Eltayeb, I.A.; Hassan, M.H.A.

1986-11-01

It is shown that the mass flux of erodible soil transported horizontally by a statistically distributed wind flow has a statistical distribution. Explicit expression for the probability density function, p.d.f., of the flux is derived for the case in which the wind speed has a Weibull distribution. The statistical distribution for a mass flux characterized by a generalized Bagnold formula is found to be Weibull for the case of zero threshold speed. Analytic and numerical values for the average horizontal mass flux of soil are obtained for various values of wind parameters, by evaluating the first moment of the flux density function. (author)

Assessment of Ground Water Quality in and around Gobichettipalayam Town Erode District, Tamilnadu

OpenAIRE

P. N. Palanisamy; A. Geetha; M. Sujatha; P. Sivakumar; K. Karunakaran

2007-01-01

Ground water samples collected from different localities in and around Gobichettipalayam town, Erode District, Tamil Nadu were analyzed for their physico- chemical characteristics. This analysis result was compared with the WHO & ICMR standards of drinking water quality parameters with the following water quality parameters namely pH, Electrical conductivity, CN-, Cl-, SO42-, Na+, K+, Ca & Mg in CaCO3 equivalents, phenolphthalein alkalinity, hydroxide alkalinity, carbonate alkalinity, bicarbo...

Evaluation of the WEPP hillslope model on stable and eroding semiarid woodlands

International Nuclear Information System (INIS)

Wilcox, B.P.; Simanton, J.R.

1995-01-01

In this paper, we evaluate runoff and erosion prediction by the WEPP hillslope model for two pinyon-juniper sites in New Mexico: one has a low erosion rate (stable site) and the other (unstable site) is eroding at very rapid rates (as a result of landuse and climatic perturbations over the last century). Runoff and erosion measurements were made at plot and hillslope scales at both sites. WEPP was evaluated using both rainfall simulation and natural rainfall data. Rainfall simulation was performed on both vegetated and bare plots. Parameter values used were developed from rainfall simulation experiments and site characteristics. In general, runoff and erosion were underpredicted at both sites but to a much larger degree at the unstable site. On the unstable site predictions were much improved when we used hydraulic conductivity (Ke) derived from the bare plot rainfall simulation. Also of importance, at the unstable site we observed a large increase in erosion as scale increased from the plot to the hillslope as a result of a well developed channel network. These results are preliminary, in that only a few storms were evaluated, however, they do suggest some important strategies for predicting the impact of reduced vegetation cover to erosion in semiarid landscapes

A novel induction motor starting method using superconduction

International Nuclear Information System (INIS)

Silva, F.B.B.; Orlando, M.T.D.; Fardin, J.F.; Simonetti, D.S.; Baldan, C.A.

2014-01-01

Highlights: • Alternative method for starting up induction motor. • Based on using a high-temperature superconductor. • A prototype of the limiter was constructed with a 2G-YBCO tape. • Prototype was tested with a 55-kW industrial induction motor in a 440-V/60-Hz. • Offers reduced current waveform distortion compared to the soft starter method. - Abstract: In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method

A novel induction motor starting method using superconduction

Energy Technology Data Exchange (ETDEWEB)

Silva, F.B.B., E-mail: flaviobarcelos@ifes.edu.br [Ifes – Federal Institute of Espírito Santo, Dept. of Industrial Automation, Serra, ES 29173087 (Brazil); UFES – Federal University of Espírito Santo, Dept. of Electrical Engineering, Vitória, ES (Brazil); Orlando, M.T.D. [UFES – Federal University of Espírito Santo, Dept. of Physics, Vitória, ES (Brazil); Fardin, J.F.; Simonetti, D.S. [UFES – Federal University of Espírito Santo, Dept. of Electrical Engineering, Vitória, ES (Brazil); Baldan, C.A. [EEL/USP – Engineering School from Lorena/University of São Paulo, SP (Brazil)

2014-12-15

Highlights: • Alternative method for starting up induction motor. • Based on using a high-temperature superconductor. • A prototype of the limiter was constructed with a 2G-YBCO tape. • Prototype was tested with a 55-kW industrial induction motor in a 440-V/60-Hz. • Offers reduced current waveform distortion compared to the soft starter method. - Abstract: In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method.

Land degradation assessment by geo-spatially modeling different soil erodibility equations in a semi-arid catchment.

Science.gov (United States)

Saygın, Selen Deviren; Basaran, Mustafa; Ozcan, Ali Ugur; Dolarslan, Melda; Timur, Ozgur Burhan; Yilman, F Ebru; Erpul, Gunay

2011-09-01

Land degradation by soil erosion is one of the most serious problems and environmental issues in many ecosystems of arid and semi-arid regions. Especially, the disturbed areas have greater soil detachability and transportability capacity. Evaluation of land degradation in terms of soil erodibility, by using geostatistical modeling, is vital to protect and reclaim susceptible areas. Soil erodibility, described as the ability of soils to resist erosion, can be measured either directly under natural or simulated rainfall conditions, or indirectly estimated by empirical regression models. This study compares three empirical equations used to determine the soil erodibility factor of revised universal soil loss equation prediction technology based on their geospatial performances in the semi-arid catchment of the Saraykoy II Irrigation Dam located in Cankiri, Turkey. A total of 311 geo-referenced soil samples were collected with irregular intervals from the top soil layer (0-10 cm). Geostatistical analysis was performed with the point values of each equation to determine its spatial pattern. Results showed that equations that used soil organic matter in combination with the soil particle size better agreed with the variations in land use and topography of the catchment than the one using only the particle size distribution. It is recommended that the equations which dynamically integrate soil intrinsic properties with land use, topography, and its influences on the local microclimates, could be successfully used to geospatially determine sites highly susceptible to water erosion, and therefore, to select the agricultural and bio-engineering control measures needed.

Granular flows on erodible layers: type and evolution of flow and deposit structures

Science.gov (United States)

Crosta, G.; De Blasio, F.; De Caro, M.; Volpi, G.; Frattini, P.

2012-04-01

The interaction of a fast moving landslide mass with the basal layer over which movement takes place has been discussed in previous contributions. Nevertheless, the evolution of the structures within the moving mass and the erodible layer are still to be described in detail (Hungr and Evans, 2004; Crosta et al., 1992, 2006, 2009, 2011; Dufresne et al., 2010; Mangeney et al., 2010) and modeling results (Crosta et al., 2006, 2009, 2011; Mangeney et al., 2010). We present some of the results from a campaign of laboratory experiments aimed at studying the evolution of a granular flow at the impact with and during the successive spreading over a cohesionless erodible layer. We performed these test to study the processes and to collect data and evidences to compare them with the results of numerical simulations and to verify capabilities of numerical codes. The laboratory setup consists of an inclined slope and an horizontal sector where release and transport, and deposition take place, respectively. Materials used for the tests are: a uniform rounded siliceous sand (Hostun sand; 0.125-0.5 mm) commonly adopted in lab tests because free of scale effects, and a gravel made of angular elements (12 mm in ave. size). Both the materials have been tested in dry conditions. Different slope angles have been tested (40, 45, 50, 55, 50, 66°) as well as different thicknesses of the erodible layer (0, 0.5, 1, 2 cm) and volumes of the released material (1.5, 3, 5, 9.6 liters). Tests have been monitored by means of a high speed camera and the pre- and post-failure geometries have been surveyed by means of a laser scanner. Deposit description allowed also the computation of volumes and the characterization of the different structures developed and frozen into the deposit. Experiments allowed us to observe the extreme processes occurring during the movement and the mise en place of the deposits. In particular, we observe the formation of a clear wave-like feature developing during the

Numerical simulation of evolutionary erodible bedforms using the particle finite element method

Science.gov (United States)

Bravo, Rafael; Becker, Pablo; Ortiz, Pablo

2017-07-01

This paper presents a numerical strategy for the simulation of flows with evolutionary erodible boundaries. The fluid equations are fully resolved in 3D, while the sediment transport is modelled using the Exner equation and solved with an explicit Lagrangian procedure based on a fixed 2D mesh. Flow and sediment are coupled in geometry by deforming the fluid mesh in the vertical direction and in velocities with the experimental sediment flux computed using the Meyer Peter Müller model. A comparison with real experiments on channels is performed, giving good agreement.

Energy saving work of frequency controlled induction cage machine

Energy Technology Data Exchange (ETDEWEB)

Gnacinski, P. [Gdynia Maritime University, Department of Ship Electrical Power Engineering, Morska Str. 8, 81-225 Gdynia (Poland)]. E-mail: piotrg@am.gdynia.pl

2007-03-15

Energy saving work, understood as lowering the supply voltage when load torque is much less than rated, is one way of reducing power losses in an induction cage machine working with a variable load. Reduction in power losses also affects the thermal properties of an induction machine because the energy saving work allows the temperature rise of the windings to decrease. Thanks to a lower temperature of the windings, the same load torque can be carried by a machine of less rated power. The ability of energy saving work to reduce the temperature of windings depends on the thermal properties of an induction machine, which are different in the case of a machine with foreign ventilation and its own ventilation. This paper deals with the thermal effect of energy saving work on a frequency controlled induction cage machine. A comparison of the properties of a machine with its own and outside ventilation is presented. The results of the investigations are shown for a 3 kW induction cage machine with the two previously mentioned ways of ventilation: one provided with a fan placed on a shaft and the other provided with a fan driven by an auxiliary motor.

Energy saving work of frequency controlled induction cage machine

International Nuclear Information System (INIS)

Gnacinski, P.

2007-01-01

Energy saving work, understood as lowering the supply voltage when load torque is much less than rated, is one way of reducing power losses in an induction cage machine working with a variable load. Reduction in power losses also affects the thermal properties of an induction machine because the energy saving work allows the temperature rise of the windings to decrease. Thanks to a lower temperature of the windings, the same load torque can be carried by a machine of less rated power. The ability of energy saving work to reduce the temperature of windings depends on the thermal properties of an induction machine, which are different in the case of a machine with foreign ventilation and its own ventilation. This paper deals with the thermal effect of energy saving work on a frequency controlled induction cage machine. A comparison of the properties of a machine with its own and outside ventilation is presented. The results of the investigations are shown for a 3 kW induction cage machine with the two previously mentioned ways of ventilation: one provided with a fan placed on a shaft and the other provided with a fan driven by an auxiliary motor

Quantifying the eroded volume of mercury-contaminated sediment using terrestrial laser scanning at Stocking Flat, Deer Creek, Nevada County, California, 2010–13

Science.gov (United States)

Howle, James F.; Alpers, Charles N.; Bawden, Gerald W.; Bond, Sandra

2016-07-28

High-resolution ground-based light detection and ranging (lidar), also known as terrestrial laser scanning, was used to quantify the volume of mercury-contaminated sediment eroded from a stream cutbank at Stocking Flat along Deer Creek in the Sierra Nevada foothills, about 3 kilometers west of Nevada City, California. Terrestrial laser scanning was used to collect sub-centimeter, three-dimensional images of the complex cutbank surface, which could not be mapped non-destructively or in sufficient detail with traditional surveying techniques.The stream cutbank, which is approximately 50 meters long and 8 meters high, was surveyed on four occasions: December 1, 2010; January 20, 2011; May 12, 2011; and February 4, 2013. Volumetric changes were determined between the sequential, three-dimensional lidar surveys. Volume was calculated by two methods, and the average value is reported. Between the first and second surveys (December 1, 2010, to January 20, 2011), a volume of 143 plus or minus 15 cubic meters of sediment was eroded from the cutbank and mobilized by Deer Creek. Between the second and third surveys (January 20, 2011, to May 12, 2011), a volume of 207 plus or minus 24 cubic meters of sediment was eroded from the cutbank and mobilized by the stream. Total volumetric change during the winter and spring of 2010–11 was 350 plus or minus 28 cubic meters. Between the third and fourth surveys (May 12, 2011, to February 4, 2013), the differencing of the three-dimensional lidar data indicated that a volume of 18 plus or minus 10 cubic meters of sediment was eroded from the cutbank. The total volume of sediment eroded from the cutbank between the first and fourth surveys was 368 plus or minus 30 cubic meters.

Lexicographic Path Induction

DEFF Research Database (Denmark)

Schürmann, Carsten; Sarnat, Jeffrey

2009-01-01

Programming languages theory is full of problems that reduce to proving the consistency of a logic, such as the normalization of typed lambda-calculi, the decidability of equality in type theory, equivalence testing of traces in security, etc. Although the principle of transfinite induction......, and weak normalization for Gödel’s T follows indirectly; both have been formalized in a prototypical extension of Twelf....

Sub ablative Er: YAG laser irradiation on surface roughness of eroded dental enamel.

Science.gov (United States)

Curylofo-Zotti, Fabiana Almeida; Lepri, Taísa Penazzo; Colucci, Vivian; Turssi, Cecília Pedroso; Corona, Silmara Aparecida Milori

2015-11-01

This study evaluated the effects of Er:YAG laser irradiation applied at varying pulse repetition rate on the surface roughness of eroded enamel. Bovine enamel slabs (n = 10) were embedded in polyester resin, ground, and polished. To erosive challenges, specimens were immersed two times per day in 20mL of concentrated orange juice (pH = 3.84) under agitation, during a two-day period. Specimens were randomly assigned to irradiation with the Er:YAG laser (focused mode, pulse energy of 60 mJ and energy density of 3.79 J/cm(2) ) operating at 1, 2, 3, or 4 Hz. The control group was left nonirradiated. Surface roughness measurements were recorded post erosion-like formation and further erosive episodes by a profilometer and observed through atomic force microscopy (AFM). Analysis of variance revealed that the control group showed the lowest surface roughness, while laser-irradiated substrates did not differ from each other following post erosion-like lesion formation. According to analysis of covariance, at further erosive episodes, the control group demonstrated lower surface roughness (P > 0.05), than any of the irradiated groups (P enamel eroded. The AFM images showed that the specimens irradiated by the Er:YAG laser at 1 Hz presented a less rough surface than those irradiated at 2, 3, and 4 Hz. © 2015 Wiley Periodicals, Inc.

Inverter-Current-Feedback Resonance-Suppression Method for LCL-Type DG System to Reduce Resonance-Frequency Offset and Grid-Inductance Effect

DEFF Research Database (Denmark)

Zhou, Leming; Zhou, Xiaoping; Chen, Yandong

2018-01-01

For the LCL-type grid-connected distributed generation system, the grid-current-feedback active damping (GCFAD) methods have a conflict between the resonance-suppression ability and harmonic-currents amplification. For this, an inverter-current-feedback reso-nance-suppression (ICFRS) method without...... additional sensors is proposed to reduce resonance-frequency offset and grid-inductance effect due to its unattenuated damping characteristic under high-frequency bandwidth. By analyzing two types of equivalent impedance models of ICFRS and GCFAD with a high-pass filter (HPF), GCFAD can suppress...

Effects of land conversion from native shrub to pistachio orchard on soil erodibility in an arid region.

Science.gov (United States)

Yakupoglu, Tugrul; Gundogan, Recep; Dindaroglu, Turgay; Kara, Zekeriya

2017-10-29

Land-use change through degrading natural vegetation for agricultural production adversely affects many of soil properties particularly organic carbon content of soils. The native shrub land and grassland of Gaziantep-Adiyaman plateau that is an important pistachio growing eco-region have been cleared to convert into pistachio orchard for the last 50 to 60 years. In this study, the effects of conversion of natural vegetation into agricultural uses on soil erodibility have been investigated. Soil samples were collected from surface of agricultural fields and adjacent natural vegetation areas, and samples were analyzed for some soil erodibility indices such as dispersion ratio (DR), erosion ratio (ER), structural stability index (SSI), Henin's instability index (I s ), and aggregate size distribution after wet sieving (AggSD). According to the statistical evaluation, these two areas were found as different from each other in terms of erosion indices except for I s index (P < 0.001 for DR and ER or P < 0.01 for SSI). In addition, native shrub land and converted land to agriculture were found different in terms of AggSD in all aggregate size groups. As a contrary to expectations, correlation tests showed that there were no any interaction between soil organic carbon and measured erodibility indices in two areas. In addition, significant relationships were determined between measured variables and soil textural fractions as statistical. These obtaining findings were attributed to changing of textural component distribution and initial aggregate size distribution results from land-use change in the study area. Study results were explained about hierarchical aggregate formation mechanism.

Use of the Maximum Torque Sensor to Reduce the Starting Current in the Induction Motor

Directory of Open Access Journals (Sweden)

Muchlas

2010-03-01

Full Text Available Use of the maximum torque sensor has been demonstrated able to improve the standard ramp-up technique in the induction motor circuit system. The induction motor used was of a three-phase squirrel-cage motor controlled using a microcontroller 68HC11. From the simulation done, it has been found that this innovative technique could optimize the performance of motor by introducing low stator current and low power consumption over the standard ramp-up technique.

Experimental and Numerical Study of the Radiant Induction-Unit and the Induction Radiant Air-Conditioning System

Directory of Open Access Journals (Sweden)

Qiang Si

2016-12-01

Full Text Available In this paper we proposed the novel air-conditioning system which combined induction ventilation and radiant air-conditioning. The indoor terminal device is the radiant induction-unit (RIDU. The RIDU is the induction unit combined with the pore radiant panel on which the copper pipes with rigid aluminum diffusion fins are installed. The two-stage evaporator chiller with the non-azeotropic mixture refrigerant is utilized in the system to reduce the initial investment in equipment. With the performance test and the steady state heat transfer model based on the theory of radiative heat transfer, the relationship between the induction ratio of the RIDU and the characteristic of the air supply was studied. Based on this, it is verified that the RIDU has a lower dew-point temperature and better anti-condensation performance than a traditional plate-type radiant panel. The characteristics of the radiation and convection heat transfer of the RIDU were studied. The total heat exchange of the RIDU can be 16.5% greater than that of the traditional plate-type radiant terminal.

Transfer of benzo[a]pyrene from microplastics to Artemia nauplii and further to zebrafish via a trophic food web experiment: CYP1A induction and visual tracking of persistent organic pollutants.

Science.gov (United States)

Batel, Annika; Linti, Frederic; Scherer, Martina; Erdinger, Lothar; Braunbeck, Thomas

2016-07-01

The uptake of microplastic particles and the transfer of potential harmful substances along with microplastics has been studied in a variety of organisms, especially invertebrates. However, the potential accumulation of very small microplastic particles along food webs ending with vertebrate models has not been investigated so far. Therefore, a simple artificial food chain with Artemia sp. nauplii and zebrafish (Danio rerio) was established to analyze the transfer of microplastic particles and associated persistent organic pollutants (POPs) between different trophic levels. Very small (1-20 μm) microplastic particles accumulated in Artemia nauplii and were subsequently transferred to fish. Virgin particles not loaded with POPs did not cause any observable physical harm in the intestinal tracts of zebrafish, although parts of the particles were retained within the mucus of intestinal villi and might even have been taken up by epithelial cells. The transfer of associated POPs was tested with the polycyclic aromatic hydrocarbon benzo[a]pyrene and an ethoxyresorufin-O-deethylase (EROD) assay for CYP1A induction in zebrafish liver as well as via fluorescence analyses. Whereas a significant induction in the EROD assay could not be shown, because of high individual variation and low sensitivity regarding substance concentration, the fluorescence tracking of benzo[a]pyrene indicates that food-borne microplastic-associated POPs may actually desorb in the intestine of fish and are thus transferred to the intestinal epithelium and liver. Environ Toxicol Chem 2016;35:1656-1666. © 2016 SETAC. © 2016 SETAC.

Deposition of eroded soil on terraced croplands in Minchet catchment, Ethiopian Highlands

Directory of Open Access Journals (Sweden)

Alemtsehay Subhatu

2017-09-01

Full Text Available In the Ethiopian Highlands, soil and water conservation practices are of utmost importance to conserve eroded soil and combat soil loss. This study provides detailed results on on-site sediment deposition and net soil loss in terraced croplands in a catchment in the sub-humid Ethiopian Highlands. Sediment deposition was measured on horse bean and maize fields during the crop growing seasons of 2014 and 2015. Measurements took place on observation plots on terraced cropland with varying spacing between terraces and varying slope gradients. Net soil loss, in this case the amount leaving the terraced cropland, was calculated by modelling the Universal Soil Loss Equation (USLE for the whole observation field and subtracting the measured sediment deposition. The study result showed about 8–11 t ha−1 sediment was deposited in the deposition zone of the terraced cropland, with greater sediment deposition on terraces with narrow spacing and steeper slope gradients. Sediment deposition was highest in July and August, and relatively low in September. Annual soil loss ranged from 32 to 37 t ha−1 in the terraced cropland of the study area. From the total soil loss in the crop growing season, about 54–74% sediment was deposited on the deposition zone of terraced crop fields. Implementation of soil and water conservation with narrow spacing, especially on the steep slopes of the sub-humid Ethiopian Highlands or other similar area, are thus highly recommended as they enable conservation of the eroded soil in the cropland.

Cranium eroding sweat gland carcinoma. A case report

International Nuclear Information System (INIS)

Arslan, M.; Karadeniz, A. N.; Aksu, G.; Guveli, M.

2005-01-01

Background. Sweat gland carcinomas are rare tumors. Eccrine sweat gland carcinomas are also very rare, with only about 200 cases reported in the world literature and only one of them was eroding the cranium. Treatment modalities of these carcinomas are not well known. Case report. Our patient was 47 years old female. Since 1989, she was operated on six times because of the tumour relapses. After each operation, the pathological results were: sweat gland adenoma, sweat gland tumour, cylindroma, turban tumour, malign cylindiroma. That was her seventh relapse. On examination, a lesion of the size 10 x 6 cm was observed in the left parietal region. Computed tomography showed the lesion had the size of 11 x 5 cm, and was destroying the tabula externa, diploic region and tabula. The tumour was invading the dura and causing periost reaction. Surgery and postoperative radiotherapy treatment was planned because of malign transformation and risk of recurrence. Conclusions. Only one case with cranium erosion was reported in literature. In our case, also intracranial extension of the tumor was observed. (author)

Differential effects of biochar on soils within an eroded field

Science.gov (United States)

Schumacher, Thomas; Chintala, Rajesh; Sandhu, Saroop; Kumar, Sandeep; Clay, Dave; Gelderman, Ron; Papiernik, Sharon; Malo, Douglas; Clay, Sharon; Julson, Jim

2015-04-01

Future uses of biochar will in part be dependent not only on the effects of biochar on soil processes but also on the availability and economics of biochar production. If pyrolysis for production of bio-oil and syngas becomes wide-spread, biochar as a by-product of bio-oil production will be widely available and relatively inexpensive compared to the production of biochar as primary product. Biochar produced as a by-product of optimized bio-oil production using regionally available feedstocks was examined for properties and for use as an amendment targeted to contrasting soils within an eroded field in an on-farm study initiated in 2013 at Brookings, South Dakota, USA. Three plant based biochar materials produced from carbon optimized gasification of corn stover (Zea mays L.), Ponderosa pine (Pinus ponderosa Lawson and C. Lawson) wood residue, and switchgrass (Panicum virgatum L.) were applied at a 1% (w/w) rate to a Maddock soil (Sandy, Mixed, Frigid Entic Hapludolls) located in an eroded upper landscape position and a Brookings soil (Fine-Silty, Mixed, Superactive, Frigid Pachic Hapludolls) located in a depositional landscape position. The cropping system within this agricultural landscape was a corn (Zea mays L.) and soybean (Glycine max L.) rotation. Biochar physical and chemical properties for each of the feedstocks were determined including pH, surface area, surface charge potential, C-distribution, ash content, macro and micro nutrient composition. Yields, nutrient content, and carbon isotope ratio measurements were made on the harvested seed. Soil physical properties measured included water retention, bulk density, and water infiltration from a ponded double ring infiltrometer. Laboratory studies were conducted to determine the effects of biochar on partitioning of nitrate and phosphorus at soil surface exchange complex and the extracellular enzymes activity of C and N cycles. Crop yields were increased only in the Maddock soil. Biochar interacted with each

The abrasive effect of commercial whitening toothpastes on eroded enamel.

Science.gov (United States)

Mosquim, Victor; Martines Souza, Beatriz; Foratori Junior, Gerson Aparecido; Wang, Linda; Magalhães, Ana Carolina

2017-06-01

To evaluate the in vitro abrasive effect of commercial whitening toothpastes on eroded bovine enamel samples in respect to erosive tooth wear. 72 bovine crowns were embedded, polished and subjected to the baseline profile analysis. The samples were then protected in 2/3 of the enamel surface and were randomly assigned to six groups (n= 12/group): G1: Oral-B 3D White, G2: Close-up Diamond Attraction Power White, G3: Sorriso Xtreme White 4D, G4: Colgate Luminous White, G5: Crest (conventional toothpaste), G6:erosion only (control). All samples were submitted to an erosive pH cycling (4 x 90 seconds in 0.1% citric acid, pH 2.5, per day) and abrasive challenges (2 x 15 seconds, per day) for 7 days. After the first and the last daily cycles, the samples were subjected to abrasive challenges, using a toothbrushing machine, soft toothbrushes and slurry of the tested toothpastes (1.5 N). Between the challenges, the samples were immersed in artificial saliva. The final profile was obtained and overlaid to the baseline profile for the calculation of the erosive tooth wear (μm). The data were subjected to Kruskal-Wallis/Dunn tests (Penamel wear (3.68±1.06 μm), similarly to G3 (3.17± 0.80 μm) and G4 (3.44± 1.29 μm). G3 and G4 performed similarly between them and compared with G5 (2.35± 1.44 μm). G2 (1.51± 0.95 μm) and G6 (0.85± 0.36 μm) showed the lowest enamel wear, which did not differ between them and from G5. Oral-B 3D White showed the highest abrasive potential while Close-up Diamond Attraction Power White showed the lowest abrasive potential on eroded enamel in vitro. This study showed that some commercial whitening toothpastes, especially those containing pyrophosphate associated with hydrated silica, enhanced enamel erosive wear.

Tracing the source of soil organic matter eroded from temperate forest catchments using carbon and nitrogen isotopes

Science.gov (United States)

Emma P. McCorkle; Asmeret Asefaw Berhe; Carolyn T. Hunsaker; Dale W. Johnson; Karis J. McFarlane; Marilyn L. Fogel; Stephen C. Hart

2016-01-01

Soil erosion continuously redistributes soil and associated soil organic matter (SOM) on the Earth's surface, with important implications for biogeochemical cycling of essential elements and terrestrial carbon sequestration. Despite the importance of soil erosion, surprisingly few studies have evaluated the sources of eroded carbon (C). We used natural abundance...

Reducing Error, Fraud and Corruption (EFC) in Social Protection Programs

OpenAIRE

Tesliuc, Emil Daniel; Milazzo, Annamaria

2007-01-01

Social Protection (SP) and Social Safety Net (SSN) programs channel a large amount of public resources, it is important to make sure that these reach the intended beneficiaries. Error, fraud, or corruption (EFC) reduces the economic efficiency of these interventions by decreasing the amount of money that goes to the intended beneficiaries, and erodes the political support for the program. ...

Power Quality Improvement in a Cascaded Multilevel Inverter Interfaced Grid Connected System Using a Modified Inductive–Capacitive–Inductive Filter with Reduced Power Loss and Improved Harmonic Attenuation

Directory of Open Access Journals (Sweden)

Meenakshi Jayaraman

2017-11-01

Full Text Available Recently, multilevel inverters are more researched due to the advantages they offer over conventional voltage source inverters in grid connected applications. Passive filters are connected at the output of these inverters to produce sinusoidal waveforms with reduced harmonics and to satisfy grid interconnection standard requirements. This work proposes a new passive filter topology for a pulse width modulated five-level cascaded inverter interfaced grid connected system. The proposed passive filter inserts an additional resistance-capacitance branch in parallel to the filter capacitor of the traditional inductive–capacitive–inductive filter in addition to a resistance in series with it to reduce damping power loss. It can attenuate the switching frequency harmonic current components much better than the traditional filter while maintaining the same overall inductance, reduced capacitance and resistance values. The basic parameter design procedure and an approach to discover the parameters of the proposed filter is introduced. Further, a novel methodology using Particle Swarm Optimization (PSO is recommended to guarantee minimum damping loss while ensuring reduced peak during resonance. In addition, PSO algorithm is newly employed in this work to maximize harmonic attenuation in and around the switching frequency on the premise of allowable values of filter inductance and capacitance. A comparative discussion considering traditional passive filters and the proposed filter is presented and evaluated through experiments conducted on a 110 V, 1 kW five-level grid connected inverter. The modulation algorithm for the multilevel inverter is implemented using a SPARTAN 6-XC6SLX25 Field Programmable Gate Array (FPGA processor. The analysis shows that the proposed filter not only provides decreased damping power loss but also is capable of providing considerable harmonic ripple reduction in the high frequency band, improved output waveforms and lesser

Effects of organic and inorganic amendments on soil erodibility

Directory of Open Access Journals (Sweden)

Nutullah Özdemir

2015-10-01

Full Text Available The objective of the present investigation is to find out the effect of incorporating of various organic and inorganic matter sources such as lime (L, zeolit (Z, polyacrylamide (PAM and biosolid (BS on the instability index. A bulk surface (0–20 cm depth soil sample was taken from Samsun, in northern part of Turkey. Some soil properties were determined as follows; fine in texture, modarete in organic matter content, low in pH and free of alkaline problem. The soil samples were treated with the inorganic and organic materials at four different levels including the control treatments in a randomized factorial block design. The soil samples were incubated for ten weeks. After the incubation period, corn was grown in all pots. The results can be summarized as organic and inorganic matter treatments increased structure stability and decreased soil erodibility. Effectiveness of the treatments varied depending on the types and levels of organic and inorganic materials.

Measuring the Amount of Eroded Soil and Surface Runoff Water in the Field

OpenAIRE

Abdulfatah Faraj Aboufayed

2013-01-01

Water erosion is the most important problems of the soil in the Jabel Nefusa area located in northwest of Libya; therefore, erosion station had been established in the Faculty of Veterinary and dryfarming research Station, University of the Al-japel Al-gharbi in Zentan. The length of the station is 72.6 feet, 6 feet width and the percentage of its slope is 3%. The station were established to measure the amount of soil eroded and amount of surface water produced during the seasons 95/96 and 96...

Dynamics of 'abc' and 'qd' constant parameters induction generator model

DEFF Research Database (Denmark)

Fajardo-R, L.A.; Medina, A.; Iov, F.

2009-01-01

In this paper, parametric sensibility effects on dynamics of the induction generator in the presence of local perturbations are investigated. The study is conducted in a 3x2 MW wind park dealing with abc, qd0 and qd reduced order, induction generator model respectively, and with fluxes as state...

Inductive reasoning.

Science.gov (United States)

Hayes, Brett K; Heit, Evan; Swendsen, Haruka

2010-03-01

Inductive reasoning entails using existing knowledge or observations to make predictions about novel cases. We review recent findings in research on category-based induction as well as theoretical models of these results, including similarity-based models, connectionist networks, an account based on relevance theory, Bayesian models, and other mathematical models. A number of touchstone empirical phenomena that involve taxonomic similarity are described. We also examine phenomena involving more complex background knowledge about premises and conclusions of inductive arguments and the properties referenced. Earlier models are shown to give a good account of similarity-based phenomena but not knowledge-based phenomena. Recent models that aim to account for both similarity-based and knowledge-based phenomena are reviewed and evaluated. Among the most important new directions in induction research are a focus on induction with uncertain premise categories, the modeling of the relationship between inductive and deductive reasoning, and examination of the neural substrates of induction. A common theme in both the well-established and emerging lines of induction research is the need to develop well-articulated and empirically testable formal models of induction. Copyright © 2010 John Wiley & Sons, Ltd. For further resources related to this article, please visit the WIREs website. Copyright © 2010 John Wiley & Sons, Ltd.

The flame retardants tetrabromobisphenol A and tetrabromobisphenol A-bisallylether suppress the induction of interleukin-2 receptor α chain (CD25) in murine splenocytes

International Nuclear Information System (INIS)

Pullen, Sabine; Boecker, Ronald; Tiegs, Gisa

2003-01-01

Polybrominated flame retardants (PBF) are frequently used additives in electronical equipment. They are ubiquitous environmental contaminants which bioaccumulate with several health effects for humans and the environment. This study investigated immunotoxic effects of the PBF tetrabromobisphenol A (TBBP A), tetrabromobisphenol A-bisallylether (TBBP A-AE), tetrabromobisphenol A-bis-(2,3-dibromopropyl-ether) (TBBP A-PE), decabromodiphenylether (DBDE), and 2,4,6-tribromophenol (TBP) in vitro. The structurally related polychlorinated aromatic hydrocarbon 3,4,3',4'-tetrachlorobiphenyl (PCB77) and dioxins mediate their immunotoxicity via the Ah-receptor gene complex. A highly relevant function of the Ah receptor, the induction of CYP 1A1 in hepatocytes of C57BL/6 mice by the established inducers 3-methylcholanthrene (MC) and PCB77 was compared to the effect of PBF by measurement of ethoxyresorufin-o-deethylase (EROD) activity. The PBF did not show any induction of CYP 1A1, while EROD activity of hepatocytes exposed to MC and PCB77 was induced 10.8- and 8.7-fold, respectively. To investigate immunotoxic effects of the flame retardants, splenocytes of C57BL/6 mice were incubated with subtoxic doses of the flame retardants and PCB77 and activated by concanavalin A (Con A). The flame retardants TBBP A and TBBP A-AE significantly inhibited the expression of interleukin-2 receptor α chain (CD25) in contrast to TBBP A-PE, DBDE, TBP, and PCB77 as shown by immunohistochemistry and quantitative analysis by laser scanning cytometry. None of the substances had any effect on the Con A-induced production of cytokines. Hence, TBBP A and TBBP A-AE may act as immunotoxic compounds by specifically inhibiting the expression of CD25

Inductive tuners for microwave driven discharge lamps

Science.gov (United States)

Simpson, James E.

1999-01-01

An RF powered electrodeless lamp utilizing an inductive tuner in the waveguide which couples the RF power to the lamp cavity, for reducing reflected RF power and causing the lamp to operate efficiently.

Some heterocyclic aromatic compounds are Ah receptor agonists in the DR-CALUX assay and the EROD assay with RTL-W1 cells.

Science.gov (United States)

Hinger, Gunnar; Brinkmann, Markus; Bluhm, Kerstin; Sagner, Anne; Takner, Helena; Eisenträger, Adolf; Braunbeck, Thomas; Engwall, Magnus; Tiehm, Andreas; Hollert, Henner

2011-09-01

Heterocyclic aromatic compounds containing nitrogen, sulfur, or oxygen heteroatoms (NSO-HET) have been detected in air, soil, marine, and freshwater systems. However, only few publications are available investigating NSO-HET using in vitro bioassays. To support better characterization of environmental samples, selected NSO-HET were screened for dioxin-like activity in two bioassays. The present study focuses on the identification and quantification of dioxin-like effects of 12 NSO-HET using the DR-CALUX assay, and the 7-ethoxyresorufin-O-deethylase (EROD) assay with the permanent fish liver cell line RTL-W1. Changes of the total medium compound concentrations during the test procedure due to, e.g., sorption or volatilization were quantified using GC/MS. The NSO-HET benzofuran, 2,3-dimethylbenzofuran, dibenzofuran, dibenzothiophen, acridine, xanthene, and carbazole caused a response in the DR-CALUX assay. Only benzofuran and 2,3-dimethylbenzofuran were also positive in the EROD assay. All other compounds were inactive in the EROD assay. Relative potency (REP) values ranged from (2.80 ± 1.32) · 10(-8) to (3.26 ± 2.03) · 10(-6) in the DR-CALUX and from (3.26 ± 0.91) · 10(-7) to (4.87 ± 1.97) · 10(-7) in the EROD assay. The REP values were comparable to those of larger polycyclic aromatic hydrocarbons, e.g., fluoranthene and pyrene. Thus, and because of the ubiquitous distribution of heterocyclic aromatic compounds in the environment, the provided data will further facilitate the bioanalytical and analytical characterization of environmental samples towards these toxicants.

Antibody induction versus corticosteroid induction for liver transplant recipients

DEFF Research Database (Denmark)

Penninga, Luit; Wettergren, André; Wilson, Colin H

2014-01-01

BACKGROUND: Liver transplantation is an established treatment option for end-stage liver failure. To date, no consensus has been reached on the use of immunosuppressive T-cell specific antibody induction compared with corticosteroid induction of immunosuppression after liver transplantation....... OBJECTIVES: To assess the benefits and harms of T-cell specific antibody induction versus corticosteroid induction for prevention of acute rejection in liver transplant recipients. SEARCH METHODS: We searched The Cochrane Hepato-Biliary Group Controlled Trials Register, the Cochrane Central Register...... to identify additional trials. SELECTION CRITERIA: We included all randomised clinical trials assessing immunosuppression with T-cell specific antibody induction versus corticosteroid induction in liver transplant recipients. Our inclusion criteria stated that participants within each included trial should...

Induction linacs

International Nuclear Information System (INIS)

Keefe, D.

1986-07-01

The principle of linear induction acceleration is described, and examples are given of practical configurations for induction linacs. These examples include the Advanced Technology Accelerator, Long Pulse Induction Linac, Radial Line Accelerator (RADLAC), and Magnetically-Insulated Electron-Focussed Ion Linac. A related concept, the auto accelerator, is described in which the high-current electron-beam technology in the sub-10 MeV region is exploited to produce electron beams at energies perhaps as high as the 100 to 1000 MeV range. Induction linacs for ions are also discussed. The efficiency of induction linear acceleration is analyzed

A Microfabricated Transduction Coil for Inductive Deep Brain Stimulation

Directory of Open Access Journals (Sweden)

Jie (Jayne WU

2006-07-01

Full Text Available "Inductively Coupled Deep Brain Stimulator" describes a chip/system design to inductively couple arbitrary waveforms to electrodes embedded in the brain for deep brain stimulation or other neurostimulation. This approach moves the conventionally implanted signal generator outside the body and provides flexibility in adjusting waveforms to investigate optimum stimulation waveforms. An "inlaid electroplating" process with through-wafer plating is used to reduce microcoil resistance and integrate microstructures and electronics. Utilizing inductive link resonance specific to microcoils, waveforms are selectively transmitted to microcoils, which further produces biphasic waveforms that are suitable for deep brain stimulation.

High current induction linacs

International Nuclear Information System (INIS)

Barletta, W.; Faltens, A.; Henestroza, E.; Lee, E.

1994-07-01

Induction linacs are among the most powerful accelerators in existence. They have accelerated electron bunches of several kiloamperes, and are being investigated as drivers for heavy ion driven inertial confinement fusion (HIF), which requires peak beam currents of kiloamperes and average beam powers of some tens of megawatts. The requirement for waste transmutation with an 800 MeV proton or deuteron beam with an average current of 50 mA and an average power of 40 MW lies midway between the electron machines and the heavy ion machines in overall difficulty. Much of the technology and understanding of beam physics carries over from the previous machines to the new requirements. The induction linac allows use of a very large beam aperture, which may turn out to be crucial to reducing beam loss and machine activation from the beam halo. The major issues addressed here are transport of high intensity beams, availability of sources, efficiency of acceleration, and the state of the needed technology for the waste treatment application. Because of the transformer-like action of an induction core and the accompanying magnetizing current, induction linacs make the most economic sense and have the highest efficiencies with large beam currents. Based on present understanding of beam transport limits, induction core magnetizing current requirements, and pulse modulators, the efficiencies could be very high. The study of beam transport at high intensities has been the major activity of the HIF community. Beam transport and sources are limiting at low energies but are not significant constraints at the higher energies. As will be shown, the proton beams will be space-charge-dominated, for which the emittance has only a minor effect on the overall beam diameter but does determine the density falloff at the beam edge

Mood induction in depressive patients: a comparative multidimensional approach.

Directory of Open Access Journals (Sweden)

Irina Falkenberg

Full Text Available Anhedonia, reduced positive affect and enhanced negative affect are integral characteristics of major depressive disorder (MDD. Emotion dysregulation, e.g. in terms of different emotion processing deficits, has consistently been reported. The aim of the present study was to investigate mood changes in depressive patients using a multidimensional approach for the measurement of emotional reactivity to mood induction procedures. Experimentally, mood states can be altered using various mood induction procedures. The present study aimed at validating two different positive mood induction procedures in patients with MDD and investigating which procedure is more effective and applicable in detecting dysfunctions in MDD. The first procedure relied on the presentation of happy vs. neutral faces, while the second used funny vs. neutral cartoons. Emotional reactivity was assessed in 16 depressed and 16 healthy subjects using self-report measures, measurements of electrodermal activity and standardized analyses of facial responses. Positive mood induction was successful in both procedures according to subjective ratings in patients and controls. In the cartoon condition, however, a discrepancy between reduced facial activity and concurrently enhanced autonomous reactivity was found in patients. Relying on a multidimensional assessment technique, a more comprehensive estimate of dysfunctions in emotional reactivity in MDD was available than by self-report measures alone and this was unsheathed especially by the mood induction procedure relying on cartoons. The divergent facial and autonomic responses in the presence of unaffected subjective reactivity suggest an underlying deficit in the patients' ability to express the felt arousal to funny cartoons. Our results encourage the application of both procedures in functional imaging studies for investigating the neural substrates of emotion dysregulation in MDD patients. Mood induction via cartoons appears to

The fate of eroded soil organic carbon along a European transect – controls after deposition in terrestrial and aquatic systems

DEFF Research Database (Denmark)

Kirkels, Frédérique; Cammeraat, Erik; Kalbitz, Karsten

that the turnover of deposited C is significantly affected by soil and organic matter properties, and whether deposition occurs in terrestrial or aquatic environments. We sampled topsoils from 10 agricultural sites along a European transect, spanning a wide range of SOC and soil characteristics (e.g. texture......The potential fate of eroded soil organic carbon (SOC) after deposition is key to understand carbon cycling in eroding landscapes. Globally, large quantities of sediments and SOC are redistributed by soil erosion on agricul-tural land, particularly after heavy precipitation events. Deposition......, aggregation, C content, etc.). Turnover of SOC was determined for terrestrial and aquatic depositional conditions in a 10-week incubation study. Moreover, we studied the impact of labile carbon inputs (‘priming’) on SOC stability using 13C labelled cellulose. We evaluated potentially important controls...

Antibody induction versus placebo, no induction, or another type of antibody induction for liver transplant recipients

DEFF Research Database (Denmark)

Penninga, Luit; Wettergren, André; Wilson, Colin H

2014-01-01

. All 19 trials were with high risk of bias. Of the 19 trials, 16 trials were two-arm trials, and three trials were three-arm trials. Hence, we found 25 trial comparisons with antibody induction agents: interleukin-2 receptor antagonist (IL-2 RA) versus no induction (10 trials with 1454 participants....... Furthermore, serum creatinine was statistically significantly higher when T-cell specific antibody induction was compared with no induction (MD 3.77 μmol/L, 95% CI 0.33 to 7.21; low-quality evidence), as well as when polyclonal T-cell specific antibody induction was compared with no induction, but this small...... T-cell specific antibody induction, drug-related adverse events were less common among participants treated with interleukin-2 receptor antagonists (RR 0.23, 95% CI 0.09 to 0.63; low-quality evidence), but this was caused by the results from one trial, and trial sequential analysis could not exclude...

Chromatic induction from surrounding stimuli under perceptual suppression.

Science.gov (United States)

Horiuchi, Koji; Kuriki, Ichiro; Tokunaga, Rumi; Matsumiya, Kazumichi; Shioiri, Satoshi

2014-11-01

The appearance of colors can be affected by their spatiotemporal context. The shift in color appearance according to the surrounding colors is called color induction or chromatic induction; in particular, the shift in opponent color of the surround is called chromatic contrast. To investigate whether chromatic induction occurs even when the chromatic surround is imperceptible, we measured chromatic induction during interocular suppression. A multicolor or uniform color field was presented as the surround stimulus, and a colored continuous flash suppression (CFS) stimulus was presented to the dominant eye of each subject. The subjects were asked to report the appearance of the test field only when the stationary surround stimulus is invisible by interocular suppression with CFS. The resulting shifts in color appearance due to chromatic induction were significant even under the conditions of interocular suppression for all surround stimuli. The magnitude of chromatic induction differed with the surround conditions, and this difference was preserved regardless of the viewing conditions. The chromatic induction effect was reduced by CFS, in proportion to the magnitude of chromatic induction under natural (i.e., no-CFS) viewing conditions. According to an analysis with linear model fitting, we revealed the presence of at least two kinds of subprocesses for chromatic induction that reside at higher and lower levels than the site of interocular suppression. One mechanism yields different degrees of chromatic induction based on the complexity of the surround, which is unaffected by interocular suppression, while the other mechanism changes its output with interocular suppression acting as a gain control. Our results imply that the total chromatic induction effect is achieved via a linear summation of outputs from mechanisms that reside at different levels of visual processing.

The impacts of grazing land management on the wind erodibility of the Mulga Lands of western Queensland, Australia

Science.gov (United States)

An estimated 100 Mt of dust is eroded by wind from the Australian land surface each year. Wind erosion may be widespread across the arid and semi-arid rangelands, with impacts on soil nutrients, carbon and ecosystem services, human health, and climate. The susceptibility of landscapes to wind erosio...

Improvement of low speed induction generator performances and reducing the power of excitation and voltage control system

Energy Technology Data Exchange (ETDEWEB)

Budisan, N. [Politechnica Univ. of Timisoara (Romania); Hentea, T.; Mahil, S. [Purdue Univ. Calumet, Hammond, IN (United States); Madescu, G. [Romanian Academy, Timisoara (Romania)

1996-12-31

In this paper we present the results of our investigations concerning the utilization of induction generators at very low speed. It is shown that, by proper design, it is possible to obtain high efficiency and high power factor values. The optimized induction generators require lower reactive power resulting in lower size and price of the excitation control system. 4 refs., 2 figs.

Multilevel DC Link Inverter for Brushless Permanent Magnet Motors with Very Low Inductance

International Nuclear Information System (INIS)

Su, G.J.

2001-01-01

Due to their long effective air gaps, permanent magnet motors tend to have low inductance. The use of ironless stator structure in present high power PM motors (several tens of kWs) reduces the inductance even further ( and lt; 100(micro)H). This low inductance imposes stringent current regulation demands for the inverter to obtain acceptable current ripple. An analysis of the current ripple for these low inductance brushless PM motors shows that a standard inverter with the most commonly used IGBT switching devices cannot meet the current regulation demands and will produce unacceptable current ripples due to the IGBT's limited switching frequency. This paper introduces a new multilevel dc link inverter, which can dramatically reduce the current ripple for brushless PM motor drives. The operating principle and design guidelines are included

Application of a particle separation device to reduce inductively coupled plasma-enhanced elemental fractionation in laser ablation-inductively coupled plasma-mass spectrometry

International Nuclear Information System (INIS)

Guillong, Marcel; Kuhn, Hans-Rudolf; Guenther, Detlef

2003-01-01

The particle size distribution of laser ablation aerosols are a function of the wavelength, the energy density and the pulse duration of the laser, as well as the sample matrix and the gas environment. Further the size of the particles affects the vaporization and ionization efficiency in the inductively coupled plasma (ICP). Some matrices produce large particles, which are not completely vaporized and ionized in the ICP. The previous work has shown that analytical results such as matrix-independent calibration, accuracy and precision can be significantly influenced by the particle sizes of the particles. To minimize the particle size related incomplete conversion of the sample to ions in the ICP a particle separation device was developed, which allows effective particle separation using centrifugal forces in a thin coiled tube. In this device, the particle cut-off size is varied by changing the number of turns in the coil, as well as by changing the gas flow and the tube diameter. The interaction of the laser with the different samples leads to varying particle size distributions. When carrying out quantitative analysis with non-matrix matched calibration reference materials, it was shown that different particle cut-off sizes were required depending on the ICP conditions and the instrument used for analysis. Various sample materials were investigated in this study to demonstrate the applicability of the device. For silicate matrices, the capability of the ICP to produce ions was significantly reduced for particles larger than 0.5 μm, and was dependent on the element monitored. To reduce memory effects caused by the separated particles, a washout procedure was developed, which additionally allowed the analysis of the trapped particles. These results clearly demonstrate the very important particle size dependent ICP-MS signal response and the potential of the described particle size based separator for the reduction of ICP induced elemental fractionation

Real-Time System Verification by Kappa-Induction

Science.gov (United States)

Pike, Lee S.

2005-01-01

We report the first formal verification of a reintegration protocol for a safety-critical, fault-tolerant, real-time distributed embedded system. A reintegration protocol increases system survivability by allowing a node that has suffered a fault to regain state consistent with the operational nodes. The protocol is verified in the Symbolic Analysis Laboratory (SAL), where bounded model checking and decision procedures are used to verify infinite-state systems by k-induction. The protocol and its environment are modeled as synchronizing timeout automata. Because k-induction is exponential with respect to k, we optimize the formal model to reduce the size of k. Also, the reintegrator's event-triggered behavior is conservatively modeled as time-triggered behavior to further reduce the size of k and to make it invariant to the number of nodes modeled. A corollary is that a clique avoidance property is satisfied.

Correlation of erosion and erodibility assessments using caesium-137

International Nuclear Information System (INIS)

Elliott, G.L.; Campbell, B.L.; Loughran, R.J.

1984-01-01

Data are presented which show that in soils in which net erosion is occurring, the content of the environmental isotope caesium-137 is highly correlated with soil loss. Other soil characteristics which may be related to the caesium content and therefore to soil loss have also been examined. Of these factors, an improved index of soil aggregate stability explained the most variation in caesium content (52%). Soil organic matter content explained 27% of variation in caesium content and other soil erodibility indices based on quantitative measurement of aggregate stability, explained between 6% and 21% of the variation. Indices based on implied hydrologic characteristics, implied aggregation and clay dispersion explained between 1% and 3% of caesium variation. It is suggested that practical factors of soil protection are relevant to the prediction of erosion hazard and may be more relevant than some indices of soil resistance. It is noted further that caesium-137 content of a soil gives every indication of being a most suitable predictor of soil erosion status

The StreamCat Dataset: Accumulated Attributes for NHDPlusV2 Catchments (Version 2.1) for the Conterminous United States: Soil Erodibility (KFFACT)

Data.gov (United States)

U.S. Environmental Protection Agency — This dataset represents the adjusted soil erodibility factor within individual, local NHDPlusV2 catchments and upstream, contributing watersheds. Attributes of the...

Inductive and deductive reasoning in obsessive-compulsive disorder.

Science.gov (United States)

Liew, Janice; Grisham, Jessica R; Hayes, Brett K

2018-06-01

This study examined the hypothesis that participants diagnosed with obsessive-compulsive disorder (OCD) show a selective deficit in inductive reasoning but are equivalent to controls in deductive reasoning. Twenty-five participants with OCD and 25 non-clinical controls made inductive and deductive judgments about a common set of arguments that varied in logical validity and the amount of positive evidence provided (premise sample size). A second inductive reasoning task required participants to make forced-choice decisions and rate the usefulness of diverse evidence or non-diverse evidence for evaluating arguments. No differences in deductive reasoning were found between participants diagnosed with OCD and control participants. Both groups saw that the amount of positive evidence supporting a conclusion was an important guide for evaluating inductive arguments. However, those with OCD showed less sensitivity to premise diversity in inductive reasoning than controls. The findings were similar for both emotionally neutral and OCD-relevant stimuli. The absence of a clinical control group means that it is difficult to know whether the deficit in diversity-based reasoning is specific to those with OCD. People with OCD are impaired in some forms of inductive reasoning (using diverse evidence) but not others (use of sample size). Deductive reasoning appears intact in those with OCD. Difficulties using evidence diversity when reasoning inductively may maintain OCD symptoms through reduced generalization of learned safety information. Copyright © 2017 Elsevier Ltd. All rights reserved.

A novel approach to determine the interphase transformer inductance of 18 pulse rectifiers

International Nuclear Information System (INIS)

Sefa, Ibrahim; Altin, Necmi

2009-01-01

The interphase transformer inductance seriously affects the performance of 18 pulse rectifiers. Low inductance values cause non-characteristic harmonics whereas high inductance values increase the rectifier cost and size. Hence, determination of the interphase transformer inductance value is an important problem in the design of 18 pulse rectifiers. In this paper, an approach to determine the optimum inductance value of an interphase transformer is proposed and a practical formula is introduced. The proposed approach has been validated with simulation and experimental studies carried out with designed capacitive loaded autotransformer based 18 pulse rectifier for different IPT inductance values at different load levels. Experimental and simulation results show that cost effective interphase transformer inductance value can be determined with the proposed approach and this value reduces the line current harmonics and improves power factor drastically.

Induction of nocebo and placebo effects on itch and pain by verbal suggestions

NARCIS (Netherlands)

Laarhoven, A.I.M. van; Vogelaar, M.L.; Wilder-Smith, O.H.G.; Riel, P.L.C.M. van; Kerkhof, P.C.M. van de; Kraaimaat, F.W.; Evers, A.W.M.

2011-01-01

Physical complaints, such as pain, can be effectively reduced by placebo effects through induction of positive expectations, or increased by nocebo effects through induction of negative expectations. In the present study, verbally induced nocebo and placebo effects on itch were experimentally

Surgical excision of eroded mesh after prior abdominal sacrocolpopexy.

Science.gov (United States)

South, Mary M T; Foster, Raymond T; Webster, George D; Weidner, Alison C; Amundsen, Cindy L

2007-12-01

months. Seven patients ultimately required abdominal excision and all had symptom resolution, however, not without complications. Two patients had bowel injury during lysis of adhesions requiring bowel resection in 1 case and repair in another, 1 had a postoperative wound infection with breakdown, 1 was readmitted for postoperative fever requiring antibiotics, and 1 had an acute coronary syndrome requiring transfer to the cardiology service. Transvaginal excision of mesh with or without endoscopy appears to be a safe and less invasive method for excision of eroded vaginal mesh after prior abdominal sacrocolpopexy. Up to 3 vaginal excision attempts may be necessary to achieve symptom resolution, and complete removal of mesh will likely improve outcomes with the transvaginal technique. Although abdominal excision can be considered the gold standard for excision of eroded mesh, it is not without potentially increased morbidity.

Measurement of the D0 WAMUS magnet inductance

International Nuclear Information System (INIS)

Kristalinski, A.; Hance, R.; Jaskierny, W.

1994-12-01

Historically, the term inductance, as it relates to magnets, has been relatively obscure at Fermilab. Confusion resulted from the typical engineering approach to the matter, whereby distinction may not have been made between analytical and beam line magnets; and distribution transformers. The latter always have a laminated core to reduce eddy currents which makes their inductance in a transitional state very close to that in a steady state. This is true only if the core material is not in saturation, which is once again the case for transformers; but not for magnets, especially the analytical ones. Based on the traditional ''transformer'' thinking, an incorrect method to measure magnet inductance was initially employed. The characteristics of a tank circuit including the magnet under test were observed. Then based on the resonant frequency and quality factor, the inductance was calculated. This method represents a very valuable tool for magnet testing where you can compare newly built magnets to a reference magnet and see if there is any difference. Although electrically correct, this method unfortunately does not reveal any valuable information which could be used to anticipate the magnet behavior under the normal working conditions. Another method of measuring inductance, based on a freewheeling discharge of the magnet, is also widely used in the Lab. To measure the inductance, a magnet is powered from a small power supply for up to 100 A to 200 A, then the power is turned off and the current decay in the magnet is recorded. Based on the dc resistance measurements and the magnet current decay data, one can determine the magnet inductance. In order to do so, the inductance is assumed to be constant and current decay is assumed to be exponential. To find out how well the effective inductance represents the real process taking place in the magnet was one of the purposes of the experiment

Does market integration buffer risk, erode traditional sharing practices and increase inequality? A test among Bolivian forager-farmers.

Science.gov (United States)

Gurven, Michael; Jaeggi, Adrian V; von Rueden, Chris; Hooper, Paul L; Kaplan, Hillard

2015-08-01

Sharing and exchange are common practices for minimizing food insecurity in rural populations. The advent of markets and monetization in egalitarian indigenous populations presents an alternative means of managing risk, with the potential impact of eroding traditional networks. We test whether market involvement buffers several types of risk and reduces traditional sharing behavior among Tsimane Amerindians of the Bolivian Amazon. Results vary based on type of market integration and scale of analysis (household vs. village), consistent with the notion that local culture and ecology shape risk management strategies. Greater wealth and income were unassociated with the reliance on others for food, or on reciprocity, but wealth was associated with a greater proportion of food given to others (i.e., giving intensity) and a greater number of sharing partners (i.e., sharing breadth). Across villages, greater mean income was negatively associated with reciprocity, but economic inequality was positively associated with giving intensity and sharing breadth. Incipient market integration does not necessarily replace traditional buffering strategies but instead can often enhance social capital.

Coupled diffusion of two species in a slab with an eroding boundary

International Nuclear Information System (INIS)

Leite, S.B.; Ozisik, M.N.; Verghese, K.

1981-01-01

The diffusion of two interchangeable species in a medium with an eroding boundary is analyzed by modeling the problem as the solution of two diffusion equations coupled at the source term for a slab with a moving boundary. Formal solutions are developed for the concentration of the two species as a function of time and position in the slab for arbitrary initial distributions of the diffusing species, arbitrary sources within the medium and boundary conditions of the third kind at the bounding surfaces. It is shown with an illustrative example, that the resulting coupled integral equations for the species can be solved very efficiently by an approach employing both a lower- and upper-bound starting function for the concentrations. (author)

Model of inductive plasma production assisted by radio-frequency wave in tokamaks

International Nuclear Information System (INIS)

Hasegawa, Makoto; Hanada, Kazuaki; Sato, Kohnosuke

2007-01-01

For initial plasma production, an induction electric field generated by applying voltage to a poloidal field (PF) coil system is used to produce a Townsend avalanche breakdown. When the avalanche margins are small, as for the International Thermonuclear Experimental Reactor (ITER) in which the induction electric field is about 0.3 V/m, the assistance of radio-frequency waves (RF) is provided to reduce the induction electric field required for reliable breakdown. However, the conditions of RF-assisted breakdown are not clear. Here, the effects of both RF and induction electric field on the RF-assisted breakdown are evaluated considering the electron loss. When traveling loss is the dominant loss, a simple model of an extended Townsend avalanche is proposed. In this model, the induction electric field required for RF-assisted breakdown can be decreased to half that required for induction breakdown. (author)

Induction machine handbook

CERN Document Server

Boldea, Ion

2002-01-01

Often called the workhorse of industry, the advent of power electronics and advances in digital control are transforming the induction motor into the racehorse of industrial motion control. Now, the classic texts on induction machines are nearly three decades old, while more recent books on electric motors lack the necessary depth and detail on induction machines.The Induction Machine Handbook fills industry's long-standing need for a comprehensive treatise embracing the many intricate facets of induction machine analysis and design. Moving gradually from simple to complex and from standard to

Phase-Inductance-Based Position Estimation Method for Interior Permanent Magnet Synchronous Motors

Directory of Open Access Journals (Sweden)

Xin Qiu

2017-12-01

Full Text Available This paper presents a phase-inductance-based position estimation method for interior permanent magnet synchronous motors (IPMSMs. According to the characteristics of phase induction of IPMSMs, the corresponding relationship of the rotor position and the phase inductance is obtained. In order to eliminate the effect of the zero-sequence component of phase inductance and reduce the rotor position estimation error, the phase inductance difference is employed. With the iterative computation of inductance vectors, the position plane is further subdivided, and the rotor position is extracted by comparing the amplitudes of inductance vectors. To decrease the consumption of computer resources and increase the practicability, a simplified implementation is also investigated. In this method, the rotor position information is achieved easily, with several basic math operations and logical comparisons of phase inductances, without any coordinate transformation or trigonometric function calculation. Based on this position estimation method, the field orientated control (FOC strategy is established, and the detailed implementation is also provided. A series of experiment results from a prototype demonstrate the correctness and feasibility of the proposed method.

Induction of Fish Biomarkers by Synthetic-Based Drilling Muds

Science.gov (United States)

Gagnon, Marthe Monique; Bakhtyar, Sajida

2013-01-01

The study investigated the effects of chronic exposure of pink snapper (Pagrus auratus Forster), to synthetic based drilling muds (SBMs). Fish were exposed to three mud systems comprised of three different types of synthetic based fluids (SBFs): an ester (E), an isomerized olefin (IO) and linear alpha olefin (LAO). Condition factor (CF), liver somatic index (LSI), hepatic detoxification (EROD activity), biliary metabolites, DNA damage and stress proteins (HSP-70) were determined. Exposure to E caused biologically significant effects by increasing CF and LSI, and triggered biliary metabolite accumulation. While ester-based SBFs have a rapid biodegradation rate in the environment, they caused the most pronounced effects on fish health. IO induced EROD activity and biliary metabolites and LAO induced EROD activity and stress protein levels. The results demonstrate that while acute toxicity of SBMs is generally low, chronic exposure to weathering cutting piles has the potential to affect fish health. The study illustrates the advantages of the Western Australian government case-by-case approach to drilling fluid management, and highlights the importance of considering the receiving environment in the selection of SBMs. PMID:23894492

NLC Hybrid Solid State Induction Modulator

CERN Document Server

Cassel, R L; Pappas, G C; Delamare, J E

2004-01-01

The Next Linear Collider accelerator proposal at SLAC requires a high efficiency, highly reliable, and low cost pulsed power modulator to drive the X-band klystrons. The original NLC envisions a solid state induction modulator design to drive up to 8 klystrons to 500 kV for 3 μs at 120 PPS with one modulator delivering greater than 1,000 MW pulse, at 500 kW average. A change in RF compression techniques resulted in only two klystrons needed pulsing per modulator at a reduced pulse width of 1.6 μsec or approximately 250 MW of the pulsed power and 80 kW of average powers. A prototype Design for Manufacturability (DFM) 8-pack modulator was under construction at the time of the change, so a redirection of modulator design was in order. To utilities the equipment which had already be fabricated, a hybrid modulator was designed and constructed using the DFM induction modulator parts and a conventional pulse transformer. The construction and performance of this hybrid two klystron Induction modul...

Cybernetic systems based on inductive logic

International Nuclear Information System (INIS)

Fry, Robert L.

2001-01-01

Recent work in the area of inductive logic suggests that cybernetics might be quantified and reduced to engineering practice. If so, then there are considerable implications for engineering, science, and other fields. This paper attempts to capture the essential ideas of cybernetics cast in the light of inductive logic. The described inductive logic extends conventional logic by adding a conjugate logical domain of questions to the logical domain of assertions intrinsic to Boolean Algebra with which most are familiar. This was first posited and developed by Richard Cox. Interestingly enough, these two logical domains, one of questions and the other of assertions, only exist relative to one another with each possessing natural measures of entropy and probability, respectively. Examples are given that highlight the utility of cybernetic approaches to neuroscience, algorithm design, system engineering, and the design and understanding of defensive and offensive systems. For example, the application of cybernetic approaches to defense systems suggests that these systems possess a wavefunction which like quantum mechanics, collapses when we 'look' through the eyes of the system sensors such as radars and optical sensors

Reducing youth internalizing symptoms: Effects of a family-based preventive intervention on parental guilt induction and youth cognitive style

Science.gov (United States)

McKEE, LAURA G.; PARENT, JUSTIN; FOREHAND, REX; RAKOW, AARON; WATSON, KELLY H.; DUNBAR, JENNIFER P.; REISING, MICHELLE M.; HARDCASTLE, EMILY; COMPAS, BRUCE E.

2014-01-01

This study utilized structural equation modeling to examine the associations among parental guilt induction (a form of psychological control), youth cognitive style, and youth internalizing symptoms, with parents and youth participating in a randomized controlled trial of a family-based group cognitive–behavioral preventive intervention targeting families with a history of caregiver depression. The authors present separate models utilizing parent report and youth report of internalizing symptoms. Findings suggest that families in the active condition (family-based group cognitive–behavioral group) relative to the comparison condition showed a significant decline in parent use of guilt induction at the conclusion of the intervention (6 months postbaseline). Furthermore, reductions in parental guilt induction at 6 months were associated with significantly lower levels of youth negative cognitive style at 12 months. Finally, reductions in parental use of guilt induction were associated with lower youth internalizing symptoms 1 year following the conclusion of the intervention (18 months postbaseline). PMID:24438999

Technique to reduce the shaft torque stress at an induction machine

Directory of Open Access Journals (Sweden)

Adrian Tulbure

2005-10-01

Full Text Available For the active attenuation at load stress in the drive shaft, the control system should receive as input signal the instantaneous shaft torque value. In this context an intelligent observer for shaft tongue of mains operatea induction machine, which is able to responding by variation of LIF (Load Input Function[1] must be developed. Extensive computer simulation prove the effectiveness of the proposed solution. In order to obtain a practical validation, the stimulated regulator has been designed and tested in the Institute of Electrical Engineering in Clausthal/Germany [2]. This paper contains following parts: Developing the mathematical model, Practical realisation, Simulations and measurements, Evaluating the control solutions and Conclusions.

Inductions Buffer Nurses' Job Stress, Health, and Organizational Commitment.

Science.gov (United States)

Kamau, Caroline; Medisauskaite, Asta; Lopes, Barbara

2015-01-01

Nurses suffer disproportionate levels of stress and are at risk of sickness-absence and turnover intentions, but there is a lack of research clarifying preventions. This study investigated the impact of inductions (job preparation courses) about mental health for nurses' job stress, general health, and organizational commitment. Data from 6,656 nurses were analyzed using structural equation modeling (SEM), showing that mental health inductions increase nurses' job satisfaction, which reduces their occupational stress and improves their health. SEM showed that these occupational health benefits increase the nurses' commitment to the organization. Job satisfaction (feeling valued, rewarded) also had a direct effect on nurses' intentions to continue working for the organization. Mental health inductions are therefore beneficial beyond job performance: they increase occupational health in the nursing profession.

Low-induction pulse current generator with a volume bus arrangement

International Nuclear Information System (INIS)

Bocharov, Yu.N.; Krivosheev, S.I.; Lapin, N.G.; Shneerson, G.A.

1993-01-01

Pulse current generator (PC6) with 38 kj stored energy designed for up to 50 kV charging voltage used to obtain magnetic fields within megagauss range, is described. Space (volume) bus arrangement of its modules is used to reduce eigen inductance of PC6. Current is commutated by solid-body spark gaps. Under 3uH inductive load PC6 provides for formation of up to 2.25 MA current pulse with 3.3x10 12 A/s pulse rise time. Technique to determine low inductances as applied to PC6 elements is described. The described PC6 is used for experiments on generation of super-strong pulse magnetic fields in single-loop solenoid with volume occupied by magnetic field, 5-7 mm. Magnetic field with up to 350 T induction amplitude is obtained in these experiments

Increasing induction motors efficiency by reducing electromagnetic loads

Directory of Open Access Journals (Sweden)

Olivian Chiver

2014-12-01

Full Text Available The efficiency of any device is a major problem today. The design and construction of high efficiency motors is strongly required from the viewpoint of reducing energy consumption and protecting the environment. This paper deal with the problem of improving efficiency by reducing electrical and magnetic loads of these motors. Using the finite elements method (FEM, the authors will study the influence of these changes on the parameters and characteristics of the initial motor.

Real And Reactive Power Saving In Three Phase Induction Machine Using Star-Delta Switching Schemes

Directory of Open Access Journals (Sweden)

Ramesh Daravath

2017-04-01

Full Text Available Induction machines are the most commonly used industrial drives for variety of applications. It has been estimated that induction motors consumes approximately 50 of all the electric energy generated. Further in the area of renewable energy sources such as wind or bio-mass energy induction machines have been found suitable for functioning as generators. In this context it may be mentioned that a star-delta switching is common for the starting of three-phase induction motor. Now it is proposed to use this star-delta switching for energy conservation of induction machines i.e. at times of reduced loads the machine switched back to star connection. Using a three-phase 400 V 50 Hz 4-pole induction machine it has been demonstrated that the star-delta switching of stator winding of three-phase induction machine motor generator operations reconnected in star at suitable reduced loads with a switching arrangement can result in improved efficiency and power factor as compared to a fixed delta or star connection. The predetermined values along with the experimental results have also been presented in this report. A simulation program has been developed for the predetermination of performance of the three-phase induction machine using exact equivalent circuit. A case study on a 250 kW 400 V 4-pole three-phase induction machine operated with different load cycles reveals the significant real and reactive power savings that could be obtained in the present proposal.

Possible Oxcarbazepine Inductive Effects on Aripiprazole Metabolism: A Case Report.

Science.gov (United States)

McGrane, Ian R; Loveland, Joshua G; de Leon, Jose

2017-01-01

Oxcarbazepine is a cytochrome P450 (CYP) 3A4 inducer, which is structurally similar to carbamazepine. Although lacking Food and Drug Administration approval, oxcarbazepine is sometimes prescribed to treat aggressive behavior in youth with autism spectrum disorder (ASD). These youths may also be taking second-generation antipsychotics, some of which are substrates of the CYP3A4 metabolic pathway. The combination of these medications may result in decreased serum antipsychotic concentrations, potentially reducing effectiveness. A limited number of reports are available which discuss reduced atypical antipsychotic concentrations secondary to oxcarbazepine CYP3A4 induction. We report a young boy taking oxcarbazepine (1200 mg/d) who presented with an unexpectedly low serum aripiprazole concentration. Utilizing therapeutic drug monitoring, pharmacogenetic testing, and a tool to evaluate drug-drug interactions, we estimate that oxcarbazepine possibly reduced his serum aripiprazole concentration by 68%. Our report is important, as it is the first to describe a drug-drug interaction between oxcarbazepine and aripiprazole. This report should encourage the completion of in vitro and clinical studies and the publication of case reports describing the possible inductive effects of oxcarbazepine on atypical antipsychotics (including cariprazine, lurasidone, quetiapine, aripiprazole, brexpiprazole, iloperidone, and risperidone) mediated by induction of the CYP3A4 metabolic pathway.

Initial Response of Pine Seedlings and Weeds to Dried Sewage Sludge in Rehabilitation of an Eroded Forest Site

Science.gov (United States)

Charles R. Berry

1977-01-01

Dried sewage sludge was applied at rates of 0, 17, 34, and 69 metric tons/ha on a badly eroded forest site in the Piedmont region of northeast Georgia. Production of weed bio mass varied directly with amount of sludge applied. Heigh growth for both shortleafand loblolly pine seedlings appeared to be greater on plots receiving 17 metric tons of sludge/ha, bu differences...

Linear induction accelerators

International Nuclear Information System (INIS)

Briggs, R.J.

1986-06-01

The development of linear induction accelerators has been motivated by applications requiring high-pulsed currents of charged particles at voltages exceeding the capability of single-stage, diode-type accelerators and at currents too high for rf accelerators. In principle, one can accelerate charged particles to arbitrarily high voltages using a multi-stage induction machine, but the 50-MeV, 10-kA Advanced Test Accelerator (ATA) at LLNL is the highest voltage machine in existence at this time. The advent of magnetic pulse power systems makes sustained operation at high-repetition rates practical, and this capability for high-average power is very likely to open up many new applications of induction machines in the future. This paper surveys the US induction linac technology with primary emphasis on electron machines. A simplified description of how induction machines couple energy to the electron beam is given, to illustrate many of the general issues that bound the design space of induction linacs

Labor Induction

Science.gov (United States)

f AQ FREQUENTLY ASKED QUESTIONS FAQ154 LABOR, DELIVERY, AND POSTPARTUM CARE Labor Induction • What is labor induction? • Why is labor induced? • What is the Bishop score? • What is “ripening ...

The Analysis and Comparison of Leakage Inductance in Different Winding Arrangements for Planar Transformer

DEFF Research Database (Denmark)

Ouyang, Ziwei; Thomsen, Ole Cornelius; Andersen, Michael Andreas E.

2009-01-01

The coupling of the windings can be easily increased by using multiply stacked planar windings connection. Interleaving is a well-known technique used to reduce leakage inductance and minimize high-frequency winding losses. The paper aims to analyze leakage inductance based on magneto motive force...

Preliminary development and evaluation of an appearance-based dissonance induction intervention for reducing UV exposure.

Science.gov (United States)

Chait, Sari R; Thompson, J Kevin; Jacobsen, Paul B

2015-01-01

The current study examined the feasibility of an appearance-based dissonance induction approach for the modification of tanning and sunscreen use behaviors. Undergraduate female students were randomized to: a healthy lifestyle condition, an appearance-based dissonance condition, or an appearance-based psychoeducation condition. Reports of tanning and sunscreen use were collected immediately before and 1 month following intervention (N=225). Relative to the healthy lifestyle condition, participants in the dissonance condition reported a significant reduction in daily hours spent tanning. Additionally, sunscreen use on the body decreased significantly for the healthy lifestyle group, but did not change for the dissonance group. The psychoeducation condition did not differ from the healthy lifestyle condition on any measure. These findings should encourage additional research into the use of dissonance induction as an appearance-based strategy for promoting reductions in UV exposure. Copyright © 2014 Elsevier Ltd. All rights reserved.

Inductive reasoning 2.0.

Science.gov (United States)

Hayes, Brett K; Heit, Evan

2018-05-01

Inductive reasoning entails using existing knowledge to make predictions about novel cases. The first part of this review summarizes key inductive phenomena and critically evaluates theories of induction. We highlight recent theoretical advances, with a special emphasis on the structured statistical approach, the importance of sampling assumptions in Bayesian models, and connectionist modeling. A number of new research directions in this field are identified including comparisons of inductive and deductive reasoning, the identification of common core processes in induction and memory tasks and induction involving category uncertainty. The implications of induction research for areas as diverse as complex decision-making and fear generalization are discussed. This article is categorized under: Psychology > Reasoning and Decision Making Psychology > Learning. © 2017 Wiley Periodicals, Inc.

Modeling and Speed Control of Induction Motor Drives Using Neural Networks

Directory of Open Access Journals (Sweden)

V. Jamuna

2010-08-01

Full Text Available Speed control of induction motor drives using neural networks is presented. The mathematical model of single phase induction motor is developed. A new simulink model for a neural network-controlled bidirectional chopper fed single phase induction motor is proposed. Under normal operation, the true drive parameters are real-time identified and they are converted into the controller parameters through multilayer forward computation by neural networks. Comparative study has been made between the conventional and neural network controllers. It is observed that the neural network controlled drive system has better dynamic performance, reduced overshoot and faster transient response than the conventional controlled system.

Risk assessment of PCDD/Fs levels in human tissues related to major food items based on chemical analyses and micro-EROD assay.

Science.gov (United States)

Tsang, H L; Wu, S C; Wong, C K C; Leung, C K M; Tao, S; Wong, M H

2009-10-01

Nine groups of food items (freshwater fish, marine fish, pork, chicken, chicken eggs, leafy, non-leafy vegetables, rice and flour) and three types of human samples (human milk, maternal serum and cord serum) were collected for the analysis of PCDD/Fs. Results of chemical analysis revealed PCDD/Fs concentrations (pg g(-1) fat) in the following ascending order: pork (0.289 pg g(-1) fat), grass carp (Ctenopharyngodon idellus) (freshwater fish) (0.407), golden thread (Nemipterus virgatus) (marine fish) (0.511), chicken (0.529), mandarin fish (Siniperca kneri) (marine fish) (0.535), chicken egg (0.552), and snubnose pompano (Trachinotus blochii) (marine fish) (1.219). The results of micro-EROD assay showed relatively higher PCDD/Fs levels in fish (2.65 pg g(-1) fat) when compared with pork (0.47), eggs (0.33), chicken (0.13), flour (0.07), vegetables (0.05 pg g(-1) wet wt) and rice (0.05). The estimated average daily intake of PCDD/Fs of 3.51 pg EROD-TEQ/kg bw/day was within the range of WHO Tolerable Daily Intake (1-4 pg WHO-TEQ/kg bw/day) and was higher than the Provisional Tolerable Daily Intake (PMTL) (70 pg for dioxins and dioxin-like PCBs) recommended by the Joint FAO/WHO Expert Committee on Food Additives (JECFA) [Joint FAO/WHO Expert Committee on Food Additives (JECFA), Summary and conclusions of the fifty-seventh meeting, JECFA, 2001.]. Nevertheless, the current findings were significantly lower than the TDI (14 pg WHO-TEQ/kg/bw/day) recommended by the Scientific Committee on Food of the Europe Commission [European Scientific Committee on Food (EU SCF), Opinions on the SCF on the risk assessment of dioxins and dioxin-like PCBs in food, 2000.]. However, it should be noted that micro-EROD assay overestimates the PCDD/Fs levels by 2 to 7 folds which may also amplify the PCDD/Fs levels accordingly. Although the levels of PCDD/Fs obtained from micro-EROD assay were much higher than those obtained by chemical analysis by 2 to 7 folds, it provides a cost-effective and

EROD activity, chromosomal damage, and oxidative stress in response to contaminants exposure in tree swallow (Tachycineta bicolor) nestlings from Great Lakes Areas of Concern

Science.gov (United States)

Custer, Thomas W.; Custer, Christine M.; Dummer, Paul; Bigorgne, Emilie; Oziolor, Elias; Karouna-Renier, Natalie K.; Schultz, Sandra; Erickson, Richard A.; Aagaard, Kevin; Matson, Cole W.

2017-01-01

Tree swallow, Tachycineta bicolor, nestlings were collected from 60 sites in the Great Lakes, which included multiple sites within 27 Areas of Concern (AOCs) and six sites not listed as AOCs from 2010 to 2014. Nestlings, approximately 12 days-of-age, were evaluated for ethoxyresorufin-O-dealkylase (EROD) activity, chromosomal damage, and six measures of oxidative stress. Data on each of these biomarkers were divided into four equal numbered groups from the highest to lowest values and the groups were compared to contaminant concentrations using multivariate analysis. Contaminant concentrations, from the same nestlings, included polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs), perfluorinated compounds (PFCs), and 17 elements. Alkylated polycyclic aromatic hydrocarbons (aPAHs) and parent PAHs (pPAHs) were measured in pooled nestling dietary samples. Polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans, and pesticides were measured in sibling eggs. Concentrations of aPAHs, pPAHs, chlordane, dieldrin, heptachlor, and PCBs, in that order, were the major contributors to the significant differences between the lowest and highest EROD activities; PFCs, PBDEs, the remaining pesticides, and all elements were of secondary importance. The four categories of chromosomal damage did not separate out well based on the contaminants measured. Concentrations of aPAHs, pPAHs, heptachlor, PCBs, chlordane, and dieldrin were the major contributors to the significant differences between the lowest and highest activities of two oxidative stress measures, total sulfhydryl (TSH) activity and protein bound sulfhydryl (PBSH) activity. The four categories of thiobarbituric acid reacting substances (TBARS), oxidized glutathione (GSSG), reduced glutathione (GSH), and the ratio of GSSG/GSH did not separate well based on the contaminants measured.

Eroding students' rural motivation: first do no harm?

Science.gov (United States)

Hurst, Samia

2014-01-01

Migration of health professionals is one of the drivers of vast inequalities in access to healthcare, as medical graduates tend to move away from both poorer countries and rural areas. One of the central ethical problems raised in attempting to alleviate these inequalities is the tension between the healthcare needs of under-served patients and the rights of medical graduates to choose their place of work and specialty. If medical graduates had greater motivation to work in under-served rural areas, this tension would decrease accordingly. Medical schools have a duty to avoid eroding existing motivation for such training and practice. This duty has practical implications. Medical students' motivation regarding their choice of specialty changes during medical training, turning them away from choices such as primary care and rural practice towards more highly specialised, more hospital based specialties. Although students may be victims of a number of biases in the initial assessment, this is unlikely to be the whole story. Students' priorities are likely to change based on their admiration for specialist role models and the visibility of the financial and non-financial rewards attached to these specialties. Students may also have a false expectation upon admission that they will be proficient in rural medicine on graduation, and change their mind once they realise the limits of their skills in that area. Although the measures required to reverse this effect currently lack a solid evidence base, they are plausible and supported by the available data.

The Dimensionality of Reasoning: Inductive and Deductive Inference can be Explained by a Single Process.

Science.gov (United States)

Hayes, Brett K; Stephens, Rachel G; Ngo, Jeremy; Dunn, John C

2018-02-01

Three-experiments examined the number of qualitatively different processing dimensions needed to account for inductive and deductive reasoning. In each study, participants were presented with arguments that varied in logical validity and consistency with background knowledge (believability), and evaluated them according to deductive criteria (whether the conclusion was necessarily true given the premises) or inductive criteria (whether the conclusion was plausible given the premises). We examined factors including working memory load (Experiments 1 and 2), individual working memory capacity (Experiments 1 and 2), and decision time (Experiment 3), which according to dual-processing theories, modulate the contribution of heuristic and analytic processes to reasoning. A number of empirical dissociations were found. Argument validity affected deduction more than induction. Argument believability affected induction more than deduction. Lower working memory capacity reduced sensitivity to argument validity and increased sensitivity to argument believability, especially under induction instructions. Reduced decision time led to decreased sensitivity to argument validity. State-trace analyses of each experiment, however, found that only a single underlying dimension was required to explain patterns of inductive and deductive judgments. These results show that the dissociations, which have traditionally been seen as supporting dual-processing models of reasoning, are consistent with a single-process model that assumes a common evidentiary scale for induction and deduction. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

The transient response for different types of erodable surface thermocouples using finite element analysis

Directory of Open Access Journals (Sweden)

Mohammed Hussein

2007-01-01

Full Text Available The transient response of erodable surface thermocouples has been numerically assessed by using a two dimensional finite element analysis. Four types of base metal erodable surface thermocouples have been examined in this study, included type-K (alumel-chromel, type-E (chromel-constantan, type-T (copper-constantan, and type-J (iron-constantan with 50 mm thick- ness for each. The practical importance of these types of thermocouples is to be used in internal combustion engine studies and aerodynamics experiments. The step heat flux was applied at the surface of the thermocouple model. The heat flux from the measurements of the surface temperature can be commonly identified by assuming that the heat transfer within these devices is one-dimensional. The surface temperature histories at different positions along the thermocouple are presented. The normalized surface temperature histories at the center of the thermocouple for different types at different response time are also depicted. The thermocouple response to different heat flux variations were considered by using a square heat flux with 2 ms width, a sinusoidal surface heat flux variation width 10 ms period and repeated heat flux variation with 2 ms width. The present results demonstrate that the two dimensional transient heat conduction effects have a significant influence on the surface temperature history measurements made with these devices. It was observed that the surface temperature history and the transient response for thermocouple type-E are higher than that for other types due to the thermal properties of this thermocouple. It was concluded that the thermal properties of the surrounding material do have an impact, but the properties of the thermocouple and the insulation materials also make an important contribution to the net response.

Contaminated soil phytoremediation by Cyperus laxus Lam. cytochrome p450 EROD-activity induced by hydrocarbons in roots.

Science.gov (United States)

López-Martínez, S; Gallegos-Martínez, M E; Pérez-Flores, L J; Gutiérrez-Rojas, M

2008-01-01

Laboratory and greenhouse experiments with Cyperus laxus Lam were conducted to determine the rate and extent of phytoremediation and the effect of hydrocarbons on the cytochrome P450 EROD (7-ethoxyresorufin-O-deethylase) enzymatic activity in roots. Plants were cultivated on hydrocarbon-contaminated soil (HCS) and spiked perlite. Phytoremediation was evaluated using 6.5 kg HCS (173 +/- 15 mg total petroleum hydrocarbons [TPH] g(-1) of dry soil) pots at different moisture contents; the average removal rate was 3.46-0.25 mg TPH g(-1) dry soil month(-1) and 48% was removed when moisture was kept at 60%. The aromatic hydrocarbon fraction was the mostly removed, 60%; aliphatic, 51%; and polar 24% after 24-month experiments. In unplanted pots, TPH concentration did not exhibit significant differences with respect to the initial concentration. We confirmed that the presence of hydrocarbons induced ERODactivity up to 6.5-fold. Moreover, short-term experiments (up to 13 d) with spiked perlite demonstrated that two EROD activities in roots contributed to the total detected; 60% was found in the cytosolic and 40% in the microsomal fraction. To our knowledge, this is the first work that tries to build links between the hydrocarbon-inducible character of ERODactivity in roots and the phytoremediation ability of C. laxus in highly contaminated soils.

Teacher induction

NARCIS (Netherlands)

Beijaard, D.; Buitink, J.; Kessels, C.; Peterson, P.; Baker, E.; McGraw, B.

2010-01-01

Teacher induction programs are intended to support the professional development of beginning teachers and thereby contribute to the reduction of teacher attrition during the early teaching years. Teacher induction programs are often based upon a deficit model with a focus on the better organization

Spatially variable rock erodibility in bedrock channels undergoing transient response to baselevel change, Great Falls area, Virginia

OpenAIRE

Shobe, Charles; Kee, Connor; Hancock, Gregory

2018-01-01

This is a poster that was presented in April 2014 at the Geological Society of America southeastern section meeting in Blacksburg, VA, USA. The poster presents rock strength and roughness data from tributaries to the Potomac River in Virginia. Our data support the idea that bedrock channel erodibility is greater on the channel margins than at the thalweg, which we hypothesize to be the result of weathering damage preferentially accumulated on the channel banks. This work was published in Shob...

Modeling and identification of induction micromachines in microelectromechanical systems applications

Energy Technology Data Exchange (ETDEWEB)

Lyshevski, S.E. [Purdue University at Indianapolis (United States). Dept. of Electrical and Computer Engineering

2002-11-01

Microelectromechanical systems (MEMS), which integrate motion microstructures, radiating energy microdevices, controlling and signal processing integrated circuits (ICs), are widely used. Rotational and translational electromagnetic based micromachines are used in MEMS as actuators and sensors. Brushless high performance micromachines are the preferable choice in different MEMS applications, and therefore, synchronous and induction micromachines are the best candidates. Affordability, good performance characteristics (efficiency, controllability, robustness, reliability, power and torque densities etc.) and expanded operating envelopes result in a strong interest in the application of induction micromachines. In addition, induction micromachines can be easily fabricated using surface micromachining and high aspect ratio fabrication technologies. Thus, it is anticipated that induction micromachines, controlled using different control algorithms implemented using ICs, will be widely used in MEMS. Controllers can be implemented using specifically designed ICs to attain superior performance, maximize efficiency and controllability, minimize losses and electromagnetic interference, reduce noise and vibration, etc. In order to design controllers, the induction micromachine must be modeled, and its mathematical model parameters must be identified. Using microelectromechanics, nonlinear mathematical models are derived. This paper illustrates the application of nonlinear identification methods as applied to identify the unknown parameters of three phase induction micromachines. Two identification methods are studied. In particular, nonlinear error mapping technique and least squares identification are researched. Analytical and numerical results, as well as practical capabilities and effectiveness, are illustrated, identifying the unknown parameters of a three phase brushless induction micromotor. Experimental results fully support the identification methods. (author)

Temporal shift of sea turtle nest sites in an eroding barrier island beach

Science.gov (United States)

Fujisaki, Ikuko; Lamont, Margaret M.; Carthy, Raymond R.

2018-01-01

Shoreline changes affect functionality of a sandy beach as a wildlife habitat and coastal erosion is among the primary causes of the changes. We examined temporal shifts in locations where loggerheads placed nests in relation to coastal erosion along a barrier island beach in the northern Gulf of Mexico. We first confirmed consistency in long-term (1855–2001), short-term (1976–2001), and more recent (2002–2012) shoreline change rates in two adjacent beach sections, one historically eroding (west beach) and the other accreting (east beach). The mean annual shoreline change rate in the two sections was significantly different in all time periods. The recent (1998–2012) mean change rate was −10.9 ± 9.9 m/year in the west beach and −2.8 ± 4.9 m/year in the east beach, which resulted in the loss of about 70% and 30% of area in the west and east beaches, respectively. Loggerheads nested significantly closer to the vegetation line in 2012 than in 2002 in the west beach but the difference between the two time periods was not significant in the east beach. However, the distance from nests to the vegetation line from 2002 to 2014 was significantly reduced annually in both beaches; on average, loggerheads nested closer to the vegetation line by 9 m/year in the west beach and 5.8 m/year in the east beach. The observed shoreline change rate and corresponding shift of nest placement sites, combined with the forecasted future beach loss, highlighted the importance of addressing the issue of beach erosion to conserve sandy beach habitats.

Effect of trifluoperazine on toxicity, HIF-1α induction and hepatocyte regeneration in acetaminophen toxicity in mice

Energy Technology Data Exchange (ETDEWEB)

Chaudhuri, Shubhra, E-mail: SCHAUDHURI@uams.edu [Department of Pediatrics, University of Arkansas for Medical Sciences, Little Rock, Arkansas (United States); Arkansas Children' s Hospital Research Institute, Little Rock, AR (United States); McCullough, Sandra S., E-mail: mcculloughsandras@uams.edu [Department of Pediatrics, University of Arkansas for Medical Sciences, Little Rock, Arkansas (United States); Arkansas Children' s Hospital Research Institute, Little Rock, AR (United States); Hennings, Leah, E-mail: lhennings@uams.edu [Department of Pathology, University of Arkansas for Medical Sciences, Little Rock, Arkansas (United States); Arkansas Children' s Hospital Research Institute, Little Rock, AR (United States); Brown, Aliza T., E-mail: brownalizat@uams.edu [Department of Pediatrics, University of Arkansas for Medical Sciences, Little Rock, Arkansas (United States); Arkansas Children' s Hospital Research Institute, Little Rock, AR (United States); Li, Shun-Hwa [Department of Pediatrics, Medical College of Wisconsin, Milwaukee, WI (United States); Simpson, Pippa M., E-mail: psimpson@mcw.edu [Department of Pediatrics, Medical College of Wisconsin, Milwaukee, WI (United States); Hinson, Jack A., E-mail: hinsonjacka@uams.edu [Department of Pharmacology and Toxicology, University of Arkansas for Medical Sciences, Little Rock, Arkansas, Arkansas Children' s Hospital Research Institute, Little Rock, AR (United States); James, Laura P., E-mail: jameslaurap@uams.edu [Department of Pediatrics, University of Arkansas for Medical Sciences, Little Rock, Arkansas (United States); Arkansas Children' s Hospital Research Institute, Little Rock, AR (United States); Department of Pharmacology and Toxicology, University of Arkansas for Medical Sciences, Little Rock, Arkansas, Arkansas Children' s Hospital Research Institute, Little Rock, AR (United States)

2012-10-15

Oxidative stress and mitochondrial permeability transition (MPT) are important mechanisms in acetaminophen (APAP) toxicity. The MPT inhibitor trifluoperazine (TFP) reduced MPT, oxidative stress, and toxicity in freshly isolated hepatocytes treated with APAP. Since hypoxia inducible factor-one alpha (HIF-1α) is induced very early in APAP toxicity, a role for oxidative stress in the induction has been postulated. In the present study, the effect of TFP on toxicity and HIF-1α induction in B6C3F1 male mice treated with APAP was examined. Mice received TFP (10 mg/kg, oral gavage) prior to APAP (200 mg/kg IP) and at 7 and 36 h after APAP. Measures of metabolism (hepatic glutathione and APAP protein adducts) were comparable in the two groups of mice. Toxicity was decreased in the APAP/TFP mice at 2, 4, and 8 h, compared to the APAP mice. At 24 and 48 h, there were no significant differences in toxicity between the two groups. TFP lowered HIF-1α induction but also reduced the expression of proliferating cell nuclear antigen, a marker of hepatocyte regeneration. TFP can also inhibit phospholipase A{sub 2}, and cytosolic and secretory PLA{sub 2} activity levels were reduced in the APAP/TFP mice compared to the APAP mice. TFP also lowered prostaglandin E{sub 2} expression, a known mechanism of cytoprotection. In summary, the MPT inhibitor TFP delayed the onset of toxicity and lowered HIF-1α induction in APAP treated mice. TFP also reduced PGE{sub 2} expression and hepatocyte regeneration, likely through a mechanism involving PLA{sub 2}. -- Highlights: ► Trifluoperazine reduced acetaminophen toxicity and lowered HIF-1α induction. ► Trifluoperazine had no effect on the metabolism of acetaminophen. ► Trifluoperazine reduced hepatocyte regeneration. ► Trifluoperazine reduced phospholipase A{sub 2} activity and prostaglandin E{sub 2} levels.

Induction heating using induction coils in series-parallel circuits

Science.gov (United States)

Matsen, Marc Rollo; Geren, William Preston; Miller, Robert James; Negley, Mark Alan; Dykstra, William Chet

2017-11-14

A part is inductively heated by multiple, self-regulating induction coil circuits having susceptors, coupled together in parallel and in series with an AC power supply. Each of the circuits includes a tuning capacitor that tunes the circuit to resonate at the frequency of AC power supply.

Characterization of the photosynthetic induction response in a Populus species with stomata barely responding to light changes.

Science.gov (United States)

Tang, Y; Liang, N

2000-08-01

The photosynthetic induction response is constrained by stomatal and biochemical limitations. However, leaves in some plants like Populus koreana x trichocarpa cv. Peace (a hybrid clone) may have little stomatal limitation because their stomata barely respond to changes in photon flux density (PFD). We examined the induction responses of leaves of well-watered and dehydrated P. koreana x trichocarpa plants grown in a high-light or a low-light regime. With an increase in PFD from 50 to 500 micromol m(-2) s(-1), steady-state stomatal conductance (g(s)) increased by only 0.25-8.2%, regardless of the initial g(s), but steady-state assimilation rate (A) increased by 550-1810%. Photosynthetic induction times required to reach 50% (IT50) and 90% (IT90) of A at high PFD were 60-90 s and 210-360 s, respectively. Examination of the dynamic relationships between A and g(s), and between A and intercellular CO2 concentration, indicated that the induction limitation was imposed completely by the biochemical components within 30-40 s after the PFD increase. Values of IT50 and IT90 were significantly higher in low-light leaves than in high-light leaves, whereas the induction state at 60 s and the induction efficiency at 60 and 120 s after the increase in PFD were lower in low-light leaves than in high-light leaves. Dehydration reduced leaf water potential (psi) significantly, resulting in a significantly decreased initial g(s). Leaf water potential had no significant effects on induction time in high-light leaves, but a low psi significantly reduced the induction time in low-light leaves. We conclude that the photosynthetic induction response was limited almost completely by biochemical components because the stomata barely responded to light changes. The biochemical limitation appeared to be higher in low-light leaves than in high-light leaves. Mild water stress may have reduced steady-state A and g(s), but it had little effect on the photosynthetic induction response in high

Reconstruction of eroded and deposited sediment volumes in the floodplains of the embanked River Waal, the Netherlands, for the period 1650 - 1850 AD

Science.gov (United States)

Hobo, Noortje; Makaske, Bart; Middelkoop, Hans

2010-05-01

The embanked floodplains of the River Waal developed as a result of stepwise downstream migration of meander bends between confining dykes. Accretion in the upstream limb of the outer bend - enhanced by groynes and trees - and erosion in the downstream limb have resulted in a series of successively developed sand bars, separated by secondary channels. On top of the sand bars and the secondary channel fills, fine-grained overbank sediments were deposited. Downstream migration ceased around 1850 AD, when the river bed was fixed by large-scale construction of groynes, and only overbank deposition continued. Eroded and deposited sediment volumes associated with downstream migration are affected by human activities. Goal of the present research is to estimate a sediment budget for a 12-km-long section along the River Waal, by quantifying the amount of erosion and deposition. We estimated these volumes for time slices of 50 years, between 1650 and 1850 AD, in order to be able to assess the variable impact of human interference during this period. To estimate erosion, we created geomorphological maps for all time slices, based on maps dating from the 17th century to present. In these maps, distinction is made between sand bars, residual channels, and older deposits (all sediments deposited before 1650 AD). Comparison between all maps allowed us to calculate the eroded area per time slice. Eroded volumes were hence estimated by multiplying the eroded area by the average river depth at that period, which is assumed to be the erosion depth. For estimation of deposition we used lithological cross-sections. These cross-sections are positioned such that every sand bar and every residual channel is represented in at least one cross-section. In every cross-section isochrones were drawn, based on OSL datings, chronologic interpretation of heavy metal profiles, and the historical maps. These isochrones are used to calculate the thickness of the sand bars, the residual channel fills

lac operon induction in Escherichia coli: Systematic comparison of IPTG and TMG induction and influence of the transacetylase LacA.

Science.gov (United States)

Marbach, Anja; Bettenbrock, Katja

2012-01-01

Most commonly used expression systems in bacteria are based on the Escherichia coli lac promoter. Furthermore, lac operon elements are used today in systems and synthetic biology. In the majority of the cases the gratuitous inducers IPTG or TMG are used. Here we report a systematic comparison of lac promoter induction by TMG and IPTG which focuses on the aspects inducer uptake, population heterogeneity and a potential influence of the transacetylase, LacA. We provide induction curves in E. coli LJ110 and in isogenic lacY and lacA mutant strains and we show that both inducers are substrates of the lactose permease at low inducer concentrations but can also enter cells independently of lactose permease if present at higher concentrations. Using a gfp reporter strain we compared TMG and IPTG induction at single cell level and showed that bimodal induction with IPTG occurred at approximately ten-fold lower concentrations than with TMG. Furthermore, we observed that lac operon induction is influenced by the transacetylase, LacA. By comparing two Plac-gfp reporter strains with and without a lacA deletion we could show that in the lacA(+) strain the fluorescence level decreased after few hours while the fluorescence further increased in the lacA(-) strain. The results indicate that through the activity of LacA the IPTG concentration can be reduced below an inducing threshold concentration-an influence that should be considered if low inducer amounts are used. Copyright © 2011 Elsevier B.V. All rights reserved.

Non-pharmacological interventions for assisting the induction of anaesthesia in children.

Science.gov (United States)

Manyande, Anne; Cyna, Allan M; Yip, Peggy; Chooi, Cheryl; Middleton, Philippa

2015-07-14

Induction of general anaesthesia can be distressing for children. Non-pharmacological methods for reducing anxiety and improving co-operation may avoid the adverse effects of preoperative sedation. To assess the effects of non-pharmacological interventions in assisting induction of anaesthesia in children by reducing their anxiety, distress or increasing their co-operation. In this updated review we searched CENTRAL (the Cochrane Library 2012, Issue 12) and searched the following databases from inception to 15 January 2013: MEDLINE, EMBASE, PsycINFO and Web of Science. We reran the search in August 2014. We will deal with the single study found to be of interest when we next update the review. We included randomized controlled trials of a non-pharmacological intervention implemented on the day of surgery or anaesthesia. At least two review authors independently extracted data and assessed risk of bias in trials. We included 28 trials (2681 children) investigating 17 interventions of interest; all trials were conducted in high-income countries. Overall we judged the trials to be at high risk of bias. Except for parental acupuncture (graded low), all other GRADE assessments of the primary outcomes of comparisons were very low, indicating a high degree of uncertainty about the overall findings. Parental presence: In five trials (557 children), parental presence at induction of anaesthesia did not reduce child anxiety compared with not having a parent present (standardized mean difference (SMD) 0.03, 95% confidence interval (CI) -0.14 to 0.20). In a further three trials (267 children) where we were unable to pool results, we found no clear differences in child anxiety, whether a parent was present or not. In a single trial, child anxiety showed no significant difference whether one or two parents were present, although parental anxiety was significantly reduced when both parents were present at the induction. Parental presence was significantly less effective than

Electric Machine with Boosted Inductance to Stabilize Current Control

Science.gov (United States)

Abel, Steve

2013-01-01

High-powered motors typically have very low resistance and inductance (R and L) in their windings. This makes the pulse-width modulated (PWM) control of the current very difficult, especially when the bus voltage (V) is high. These R and L values are dictated by the motor size, torque (Kt), and back-emf (Kb) constants. These constants are in turn set by the voltage and the actuation torque-speed requirements. This problem is often addressed by placing inductive chokes within the controller. This approach is undesirable in that space is taken and heat is added to the controller. By keeping the same motor frame, reducing the wire size, and placing a correspondingly larger number of turns in each slot, the resistance, inductance, torque constant, and back-emf constant are all increased. The increased inductance aids the current control but ruins the Kt and Kb selections. If, however, a fraction of the turns is moved from their "correct slot" to an "incorrect slot," the increased R and L values are retained, but the Kt and Kb values are restored to the desired values. This approach assumes that increased resistance is acceptable to a degree. In effect, the heat allocated to the added inductance has been moved from the controller to the motor body, which in some cases is preferred.

Apparatus and method for reducing inductive coupling between levitation and drive coils within a magnetic propulsion system

Science.gov (United States)

Post, Richard F.

2001-01-01

An apparatus and method is disclosed for reducing inductive coupling between levitation and drive coils within a magnetic levitation system. A pole array has a magnetic field. A levitation coil is positioned so that in response to motion of the magnetic field of the pole array a current is induced in the levitation coil. A first drive coil having a magnetic field coupled to drive the pole array also has a magnetic flux which induces a parasitic current in the levitation coil. A second drive coil having a magnetic field is positioned to attenuate the parasitic current in the levitation coil by canceling the magnetic flux of the first drive coil which induces the parasitic current. Steps in the method include generating a magnetic field with a pole array for levitating an object; inducing current in a levitation coil in response to motion of the magnetic field of the pole array; generating a magnetic field with a first drive coil for propelling the object; and generating a magnetic field with a second drive coil for attenuating effects of the magnetic field of the first drive coil on the current in the levitation coil.

Propensity score method for analyzing the effect of labor induction in prolonged pregnancy.

Science.gov (United States)

Pyykönen, Aura; Tapper, Anna-Maija; Gissler, Mika; Haukka, Jari; Petäjä, Jari; Lehtonen, Lasse

2018-04-01

There is an ongoing debate on the optimal time of labor induction to reduce the risks associated with prolonged pregnancy. Registry-based study of 212 716 term, singleton cephalic deliveries between 2006 and 2012 in Finland comparing the outcomes of labor induction with those of expectant management in five, three-day gestational age periods between 40 and 42 weeks (group 1: 40 +0 -40 +2 ; group 2: 40 +3 -40 +5 ; group 3: 40 +6 -41 +1 ; group 4: 41 +2 -41 +4 ; group 5: 41 +5 -42 +0 ). Using Poisson regression, induced deliveries in each of the gestational age periods were compared with all ongoing pregnancies. Propensity score matching was applied to reduce confounding by indication. In the gestational age groups 1 and 2, labor induction significantly decreased the risk of meconium aspiration syndrome [relative risk (RR) 0.40, 95% confidence interval (CI) 0.18-0.91 (group 1), RR 0.44, 95% CI 0.21-0.91 (group 2)] but increased the risk for prolonged hospitalization of a neonate [RR 1.30, 95% CI 1.10-1.54 (group 1) and RR 1.23, 95% CI 1.03-1.47 (group 2)]. In groups 3 and 4, labor induction significantly increased the risk for emergency cesarean section [RR 1.17, 95% CI 1.06-1.28 (group 3) and RR 1.19, 95% CI 1.09-1.29 (group 4)] but still reduced the risk for meconium aspiration syndrome. In group 5, labor induction did not affect the risk for any of the studied outcomes (operative delivery, obstetric trauma, neonatal mortality, respirator treatment, Apgar <7). Propensity score matching is a novel approach to studying the effect of labor induction. It highlighted the conflicting maternal and neonatal risks and benefits of the intervention, and supported expectant management as a valid option, at least until close to 42 weeks. © 2017 Nordic Federation of Societies of Obstetrics and Gynecology.

Precise derating of three phase induction motors with unbalanced voltages

International Nuclear Information System (INIS)

Faiz, Jawad; Ebrahimpour, H.

2007-01-01

Performance analysis of three phase induction motors under supply voltage unbalance conditions is normally conducted using the well-known symmetrical components analysis. In this analysis, the voltage unbalance level at the terminals of the machine is assessed by means of the NEMA or IEC definitions. Both definitions lead to a relatively large error in predicting the performance of a machine. A method has recently been proposed in which, in addition to the voltage unbalance factor (VUF), the phase angle has been taken into account in the analysis. This means that the voltage unbalance factor is regarded as a complex value. This paper shows that although the use of the complex VUF reduces the computational error considerably, it is still high. This is proven by evaluating the derating factor of a three phase induction motor. A method is introduced to determine the derating factor precisely using the complex unbalance factor for an induction motor operating under any unbalanced supply condition. A practical case for derating of a typical three phase squirrel cage induction motor supplied by an unbalanced voltage is studied in the paper

Induction stoves as an option for clean cooking in rural India

International Nuclear Information System (INIS)

Banerjee, Manjushree; Prasad, Rakesh; Rehman, Ibrahim H; Gill, Bigsna

2016-01-01

As part of a programme on ‘access to clean cooking alternatives in rural India’, induction stoves were introduced in nearly 4000 rural households in Himachal Pradesh, one of the few highly electrified states in India. Analysis of primary usage information from 1000 rural households revealed that electricity majorly replaced Liquid Petroleum Gas (LPG), generally used as a secondary cooking fuel, but did not influence a similar shift from traditional mud stoves as the primary cooking technology. Likewise, the shift from firewood to electricity as a primary cooking fuel was observed in only 5% of the households studied. Country level analysis indicates that rural households falling in lower monthly per capita expenditure (MPCE) classes have lesser access to electricity and clean cooking options than those falling in higher MPCE classes. Again, only three states in India with high levels of rural household electrification report consumption statuses more than 82 kWh per month (the estimated mean for electricity consumption by induction stoves). Overall, the results of the study indicate that induction stoves will have limited potential in reducing the consumption of firewood and LPG if included in energy access programmes, that too only in regions where high levels of electrification exist. - Highlights: • Primary survey of induction stove users was conducted in 1000 rural households. • In 84% households, electricity replaced LPG as the secondary cooking fuel. • In only 5% households, electricity replaced firewood as the primary cooking fuel. • Electricity as a cooking fuel for rural India still needs massive investments. • Currently, induction stoves are only able to reduce consumption of firewood and LPG.

Improved focus solenoid design for linear induction accelerators

International Nuclear Information System (INIS)

Zentler, J.M.; Van Maren, R.D.; Nexsen, W.E.

1992-08-01

Our FXR linear induction accelerator produces a 2 KA, 17 MeV electron beam of 60 ns duration. The beam is focused on a tantalum target to produce x-rays for radiography. The FWHM spot size of the focused beam is currently 2.2 mm. We strive to reduce the spot size by 30% by improving the field characteristics of focusing solenoids housed in each of 50 induction cells along the beamline. Tilts in the magnetic axis of the existing solenoids range up to 12 mrad (0.7 degrees). We are building new solenoid assemblies which include ferromagnetic homogenizer rings. These dramatically reduce field errors. A field tilt of under 0.5 mrad has been achieved. Mechanical alignment of the rings is critical. We developed a novel construction method in which the rings are wound with 4 mil thick Si-Fe ribbon into grooves on an aluminum cylinder. The cylinder then becomes the winding mandrel for the focus solenoids. This forms a more accurate and compact assembly than the standard practice of pressing individual solid rings onto a tube

Inductance loop and partial

CERN Document Server

Paul, Clayton R

2010-01-01

"Inductance is an unprecedented text, thoroughly discussing "loop" inductance as well as the increasingly important "partial" inductance. These concepts and their proper calculation are crucial in designing modern high-speed digital systems. World-renowned leader in electromagnetics Clayton Paul provides the knowledge and tools necessary to understand and calculate inductance." "With the present and increasing emphasis on high-speed digital systems and high-frequency analog systems, it is imperative that system designers develop an intimate understanding of the concepts and methods in this book. Inductance is a much-needed textbook designed for senior and graduate-level engineering students, as well as a hands-on guide for working engineers and professionals engaged in the design of high-speed digital and high-frequency analog systems."--Jacket.

Possibility of reducing stray losses and parasitic torques in two-phase emergency feeding of induction motors

Czech Academy of Sciences Publication Activity Database

Schreier, Luděk; Bendl, Jiří; Chomát, Miroslav; Klíma, J.

2006-01-01

Roč. 51, č. 2 (2006), s. 109-131 ISSN 0001-7043 R&D Projects: GA ČR(CZ) GA102/04/0215 Institutional research plan: CEZ:AV0Z20570509 Keywords : induction motor * emergency operation of electrical drives * stray losses Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

Energy efficiency in speed control system for induction motors; Eficiencia energetica em sistema de controle de velocidade em motores de inducao

Energy Technology Data Exchange (ETDEWEB)

Silva, Arlete Vieira da; Ribeiro, Elisangela do Nascimento; Tenorio, Iana Cavalcanti; Horta, Mario Marcos Brito [Centro Universitario de Belo Horizonte (UnBH), MG (Brazil)], e-mails: arlete.silva@prof.unibh.br, nr.elisangela@gmail.com, ianactenorio@gmail.com, mario_bhorta@yahoo.com.br

2011-07-01

This work has as objective the study of energy efficiency of induction motors fed by frequency inverters, since this is a practical resource that has progressively allowed the replacement of mechanical speed reducers. In this work the speed control of induction motors of the squirrel cage has steeped through the frequency inverters using scalar control. Induction motors are frequently used in industrial applications due to its simple construction, its low maintenance and reduced in size. It was possible through tests made at UNI-BH Electrical Engineering laboratory to obtain satisfactory results regarding the performance of the inverter CFW08 (WEG), speed control of induction motor. (author)

Soil aggregates, organic matter turnover and carbon balance in a Mediterranean eroded vineyard

Science.gov (United States)

Novara, Agata; Lo Papa, Giuseppe; Dazzi, Carmelo; Gristina, Luciano; Cerdà, Artemi

2014-05-01

The carbon cycle is being affected by the human impacts (Novara et al., 2011; Yan-Gui et al., 2013), and one of those is the intensification in the soil erosion in agriculture land (Cerdà et al., 2009; García Orenes et al., 2009). Vineyards also are affected by the human activities (Fernández Calviño, 2012). Vineyards in Sicily are cultivated on 110.000 ha, 10% of which on >10% slope. Deficiencies of soil organic matter are typical of the semi arid Mediterranean environment especially where traditional intensive cropping practices are adopted (Novara et al., 2012; 2013). These practices in vineyards could lead soil to intensive erosion processes (Novara et al., 2011). The fate of SOC under erosion processes is difficult to understand because of the influence of the erosion impact on SOC pathway, which depends on the different features of the process involved (detachment, transport and/or deposition). Soil erosion must be considered a net C source (Lal, 2003), as eroded soils have lower net primary productivity (NPP) (Dick and Gregorich, 2004) caused by reduction in the effective rooting depth and all in all determining decline in soil quality. Breakdown of aggregates and soil dispersion expose SOM to microbial/enzymatic processes and chemical soil properties (Dimoyiannis, 2012; Kocyigit and Demirci, 2012). Moreover the light fraction, transported by runoff, is labile and easily mineralized determining CO2 emission in the atmosphere (Jacinthe and Lal, 2004). Therefore, the carbon pool is lower in eroded than in un-eroded soil scapes and the rate of mineralization of soil organic matter is higher in sediments than in original soil. In this survey we show a research conducted on a slope sequence of three soil profiles in an irrigated vineyard located in Sambuca di Sicilia, Italy (UTM33-WGS84: 4169367N; 325011E). The SOC content was measured at depth intervals of 10 cm up to a depth of 60 cm in each pedon. Wet aggregate-size fractions with no prior chemical

A taxonomy of inductive problems.

Science.gov (United States)

Kemp, Charles; Jern, Alan

2014-02-01

Inductive inferences about objects, features, categories, and relations have been studied for many years, but there are few attempts to chart the range of inductive problems that humans are able to solve. We present a taxonomy of inductive problems that helps to clarify the relationships between familiar inductive problems such as generalization, categorization, and identification, and that introduces new inductive problems for psychological investigation. Our taxonomy is founded on the idea that semantic knowledge is organized into systems of objects, features, categories, and relations, and we attempt to characterize all of the inductive problems that can arise when these systems are partially observed. Recent studies have begun to address some of the new problems in our taxonomy, and future work should aim to develop unified theories of inductive reasoning that explain how people solve all of the problems in the taxonomy.

Estimativa da erodibilidade pela desagregação por ultra-som e atributos de solos com horizonte B textural Estimating soil erodibility from sonication indexes and other attributes of textural B horizon soils

Directory of Open Access Journals (Sweden)

Marcos Aurélio Carolino de Sá

2004-07-01

Full Text Available A erodibilidade de solos é um fator importante na estimativa das perdas por erosão. Este fator é uma expressão da combinação de atributos do solo, os quais possibilitam sua estimativa por meio de equações. O objetivo deste trabalho foi medir atributos químicos e mineralógicos que, combinados com índices de estabilidade de agregados determinados por ultra-som, pudessem ser utilizados como variáveis em modelos na estimativa da erodibilidade de solos com horizonte B textural do Brasil. Estes atributos foram determinados em 22 solos de erodibilidade conhecida, medida diretamente em parcelas no campo. Atributos de 21 dos solos foram utilizados no ajuste dos modelos. Um dos solos (Argissolo Vermelho-Amarelo foi escolhido ao acaso para teste. De 96 variáveis, 15 foram incluídas nos modelos de estimativa da erodibilidade. A maioria delas é representada por índices de desagregação por sonificação de amostras do horizonte A. Foram obtidos quatro modelos para estimar a erodibilidade, com R² variando entre 0,83** e 0,91**. A erodibilidade pode ser estimada com base na estabilidade de agregados por ultra-som.Soil erodibility is an important factor for estimating soil erosion losses. This factor is an expression of combined soil attributes, which make possible its estimation by equations. The objective of this study was to measure some chemical and mineralogical attributes, and to combine them with aggregate stability indexes from sonication analysis, in equations in order to estimate soil erodibility of textural B horizon soils from Brazil. These attributes were measured for 22 soils that had their erodibility measured from field plots. Attributes of 21 soils were used to adjust the equations. One of the soils (Red-Yellow Argisol was used to test the equations. From 96 variables, 15 were significantly correlated to soil erodibility. Most of them are represented by the disruption indexes from sonication analysis of A horizon samples. This

Half Bridge Inductive Heater

Directory of Open Access Journals (Sweden)

Zoltán GERMÁN-SALLÓ

2015-12-01

Full Text Available Induction heating performs contactless, efficient and fast heating of conductive materials, therefore became one of the preferred heating procedure in industrial, domestic and medical applications. During induction heating the high-frequency alternating currents that heat the material are induced by means of electromagnetic induction. The material to be heated is placed inside the time-varying magnetic field generated by applying a highfrequency alternating current to an induction coil. The alternating electromagnetic field induces eddy currents in the workpiece, resulting resistive losses, which then heat the material. This paper describes the design of a power electronic converter circuit for induction heating equipment and presents the obtained results. The realized circuit is a low power half bridge resonant inverter which uses power MOS transistors and adequate driver circuits.

Effect of farmyard manure, mineral fertilizers and mung bean residues on some microbiological properties of eroded soil in district Swat

Directory of Open Access Journals (Sweden)

M. Naeem

2009-05-01

Full Text Available The present study was conducted to evaluate the efficacy of organic and inorganic fertilizers and mung bean residues on improving microbiological properties of eroded lands of District Swat, North West Frontier Province (NWFP Pakistan under wheat-mung bean-wheat cropping system during 2006 to 2008. The experiment was laid out in RCBD split-plot arrangement. Mung bean was grown and a basal dose of 25-60 kg N-P2O5 ha-1 was applied. After mung bean harvest, three residues management practices, i.e., R+ (mung bean residues incorporated into soil, R- (mung bean residues removed and F (fallow were performed in the main-plots. Sub-plot factor consisted of six fertilizer treatments for wheat crop i.e., T1 (control, T2 (120 kg N ha-1, T3 (120-90-0 kg N-P2O5-K2O ha-1, T4 (120-90-60 kg N-P2O5-K2O ha-1, T5 (90-90-60 kg N-P2O5-K2O + 10 t FYM ha-1 and T6 (60-90-60 kg N-P2O5- K2O + 20 t FYM ha-1. The results showed that microbial activity, microbial biomass-C and-N, mineralizable C and N were highest with T6 as well as with the incorporation of mung bean residues (R+. Compared with control, T6 increased microbial biomass C, N, mineralizable C and N by 33.8, 164.1, 35.5 and 110.6% at surface and 38.4, 237.5, 38.7 and 124.1% at sub-surface soil, respectively, while R+ compared with fallow increased these properties by 33.7, 47.4, 21.4 and 32.2% at surface and 36.8, 51, 21.9 and 35.4% at sub-surface soil, respectively. Inclusion of mung bean with its residues incorporated and application of 20 t FYM ha-1 and reducing inorganic N fertilizer to 60 kg N ha-1 for wheat is recommended for improving microbiological properties of slightly eroded lands

Inductive Reasoning and Writing

Science.gov (United States)

Rooks, Clay; Boyd, Robert

2003-01-01

Induction, properly understood, is not merely a game, nor is it a gimmick, nor is it an artificial way of explaining an element of reasoning. Proper understanding of inductive reasoning--and the various types of reasoning that the authors term inductive--enables the student to evaluate critically other people's writing and enhances the composition…

Effect of Home Cage Bedding in the Induction Chamber on Serum Cortisol and Corticosterone Levels in Response to Isoflurane-induced Anesthesia in C57BL/6J Mice.

Science.gov (United States)

Reiter, Cara P; Christy, Amanda C; Olsen, Cara H; Bentzel, David E

2017-03-01

Mice are routinely anesthetized with isoflurane in an induction chamber. The AVMA Guidelines for the Euthanasia of Animals states that distress should be minimized during euthanasia but does not address this point in regard to induction of anesthesia. Here we evaluated the potential for familiar surroundings to reduce the adrenocortical response of mice during anesthesia induction with isoflurane. However, adding bedding from the animals' home cage to the induction chamber failed to significantly reduce serum cortisol or corticosterone levels in male and female C57BL/6J mice. These results indicate that familiar surroundings do not appear sufficient to reduce the adrenocortical response of mice during anesthesia induction with isoflurane.

Design of a low parasitic inductance SiC power module with double-sided cooling

Energy Technology Data Exchange (ETDEWEB)

Yang, Fei [The University of Tennessee, Knoxville; Liang, Zhenxian [Cree Inc.; Wang, Fei [ORNL; Wang, Zhiqiang [ORNL

2017-03-01

In this paper, a low-parasitic inductance SiC power module with double-sided cooling is designed and compared with a baseline double-sided cooled module. With the unique 3D layout utilizing vertical interconnection, the power loop inductance is effectively reduced without sacrificing the thermal performance. Both simulations and experiments are carried out to validate the design. Q3D simulation results show a power loop inductance of 1.63 nH, verified by the experiment, indicating more than 60% reduction of power loop inductance compared with the baseline module. With 0Ω external gate resistance turn-off at 600V, the voltage overshoot is less than 9% of the bus voltage at a load of 44.6A.

MODELING CONTROLLED ASYNCHRONOUS ELECTRIC DRIVES WITH MATCHING REDUCERS AND TRANSFORMERS

Directory of Open Access Journals (Sweden)

V. S. Petrushin

2015-04-01

Full Text Available Purpose. Working out of mathematical models of the speed-controlled induction electric drives ensuring joint consideration of transformers, motors and loadings, and also matching reducers and transformers, both in static, and in dynamic regimes for the analysis of their operating characteristics. Methodology. At mathematical modelling are considered functional, mass, dimensional and cost indexes of reducers and transformers that allows observing engineering and economic aspects of speed-controlled induction electric drives. The mathematical models used for examination of the transitive electromagnetic and electromechanical processes, are grounded on systems of nonlinear differential equations with nonlinear coefficients (parameters of equivalent circuits of motors, varying in each operating point, including owing to appearances of saturation of magnetic system and current displacement in a winding of a rotor of an induction motor. For the purpose of raise of level of adequacy of models a magnetic circuit iron, additional and mechanical losses are considered. Results. Modelling of the several speed-controlled induction electric drives, different by components, but working on a loading equal on character, magnitude and a demanded control range is executed. At use of characteristic families including mechanical, at various parameters of regulating on which performances of the load mechanism are superimposed, the adjusting characteristics representing dependences of a modification of electrical, energy and thermal magnitudes from an angular speed of motors are gained. Originality. The offered complex models of speed-controlled induction electric drives with matching reducers and transformers, give the chance to realize well-founded sampling of components of drives. They also can be used as the design models by working out of speed-controlled induction motors. Practical value. Operating characteristics of various speed-controlled induction electric

Biomarker responses in persian sturgeon (Acipenser persicus exposed to benzo-a-pyrene and beta-naphthoflavone

Directory of Open Access Journals (Sweden)

Karimzadeh Katayoon

2013-01-01

Full Text Available Biotransformation enzymes of xenobiotics (ethoxyresorufin-O-deethylase, cytochrome P4501A1 content and glutathione-S-transferase were investigated in the liver of Persian Sturgeon (Acipenser persicus after a 96-hour exposure to polycyclic aromatic hydrocarbons (PAHs, premutagenic benzo[a]pyrene (BaP and beta-naphthoflavone (BNF. The fish were injected 10 mg/kg wet-body weight in corn oil for 96 hours every days. Ethoxyresorufin-O-deethylase activity (EROD and glutathione s-transferase activity (GST were measured in the fish liver. Cytochrome P4501A1 (CYP1A1 content was estimated by indirect enzyme-linked immunosorbent assay (ELISA. The response appeared as early as 12 hours post exposure. A time-dependent response was observed in the EROD activity, being significantly higher at 48 hours post exposure to 10 mg/kg of BaP. The greatest induction occurred in the fish treated with 10 mg/kg BaP, in which a 32.1- fold increase in EROD activity was observed. Results showed that EROD activity in A. persicus is significantly increased by BaP and BNF treatments. Both chemicals showed higher values of EROD activity compared to the liver CYP1A content. There was a rise in glutathione-S-transferase activity in fish exposed to BNF, but no increase was observed in fish treated with BaP. The results showed that hepatic CYP1A expression in terms of induction of EROD activity might be suited as a biomarker of organic contamination in aquatic environments and led to lower sensitivity of the second phase in the detoxification enzyme.

Fuel saver based on electromagnetic induction for automotive engine

Science.gov (United States)

Siregar, Houtman P.; Sibarani, Maradu

2007-12-01

In the considered research is designed and analyzed the performance of the fuel saver which is based on electromagnetic induction for automotive diesel engine. The fuel saver which is based on permanent magnet has sold in market and its performance has tested. In comparison to the former fuel saver, in the proposed work is produced fuel saver which is based on electromagnetic induction. The considered research is the continuation of my former work. Performance of the produced fuel saver which is installed in the fuel line of internal combustion engine rig is compared to the performance of the standard internal combustion engine rig Speed of the engine, wire diameter of coil, and number of coil which is coiled in the winding of the the fuel saver are chosen as the testing variables. The considered research has succeeded to design the fuel saver which is based on electromagnetic induction for saving the automotive fuel consumption. Results of the research show that the addition of the fuel saver which is based on electromagnetic induction to the flow of the diesel fuel can significantly save the automative fuel consumption. In addition the designed fuel saver can reduce the opacity of the emission gas.

Effects of induction heating parameters on controlling residual stress in intermediate size pipes

International Nuclear Information System (INIS)

Rybicki, E.F.; McGuire, P.A.

1981-01-01

Induction heating for stress improvement (IHSI) is a method for reducing the tensile weld induced stresses on the inner surfaces of the girth welded pipes. The process entails inductively heating the outside of a welded pipe while cooling the inner surface with flowing water. A 10-inch schedule 80 Type 304 stainless steel pipe was selected for this study. Residual stresses due to welding were first determined using a finite element computational model. 26 refs

Erodibility of cement-stabilized tropical soils in highway engineering in Togo

International Nuclear Information System (INIS)

Eklu-Natey, T.E.D.

1992-01-01

This work contains a methodical study on the suceptibility to weather of cement-stabilized tropical soils of Togo by simulating on the one hand the climatic conditions of the original surroundings and on the other hand the variations occuring in situ of the degree of saturation and compaction. The chosen tests ensure for the first time a simple execution and at the same time reproducible numerical values of the results achieved. From results of the slaking, erosion, adhesion, durability and swelling tests clear parameters and classification criteria were derived which help to forecast the susceptibility to weather of soils in tropical climates. A method for the determination of the reaction to water of soils is proposed consisting of a particular process of derivation and interpretation of the consistency value for a given swelling rate. Moreover a possibility is recommended with which the time-consuming and expensive mineralogical analyses which were frequently used in the past for torpical soils can be avoided. The proposed evaluation criteria provides civil engineers working in permanently moist, arid or intermittently moist tropical regions with practical and theoretical bases for the estimation of the erodibility of soils. (orig./BBR) [de

Induction melter apparatus

Science.gov (United States)

Roach, Jay A [Idaho Falls, ID; Richardson, John G [Idaho Falls, ID; Raivo, Brian D [Idaho Falls, ID; Soelberg, Nicholas R [Idaho Falls, ID

2008-06-17

Apparatus and methods of operation are provided for a cold-crucible-induction melter for vitrifying waste wherein a single induction power supply may be used to effect a selected thermal distribution by independently energizing at least two inductors. Also, a bottom drain assembly may be heated by an inductor and may include an electrically resistive heater. The bottom drain assembly may be cooled to solidify molten material passing therethrough to prevent discharge of molten material therefrom. Configurations are provided wherein the induction flux skin depth substantially corresponds with the central longitudinal axis of the crucible. Further, the drain tube may be positioned within the induction flux skin depth in relation to material within the crucible or may be substantially aligned with a direction of flow of molten material within the crucible. An improved head design including four shells forming thermal radiation shields and at least two gas-cooled plenums is also disclosed.

Regulation of the cellulolytic system in Trichoderma reesei by sophorose: induction of cellulase and repression of beta-glucosidase.

OpenAIRE

Sternberg, D; Mandels, G R

1980-01-01

Sophorose has two regulatory roles in the production of cellulase enzymes in Trichoderma reesei: beta-glucosidase repression and cellulase induction. Sophorose also is hydrolyzed by the mycelial-associated beta-glucosidase. Repression of beta-glucosidase reduces sophorose hydrolysis and thus may increase cellulase induction.

Eroding dipoles and vorticity growth for Euler flows in {{{R}}}^{3}: the hairpin geometry as a model for finite-time blowup

Science.gov (United States)

Childress, Stephen; Gilbert, Andrew D.

2018-02-01

A theory of an eroding ‘hairpin’ vortex dipole structure in three-dimensions is developed, extending our previous study of an axisymmetric eroding dipole without swirl. The axisymmetric toroidal dipole was found to lead to maximal growth of vorticity, as {t}4/3. The hairpin is here similarly proposed as a model to produce large ‘self-stretching’ of vorticity, with the possibility of finite-time blow-up. We derive a system of partial differential equations of ‘generalized’ form, involving contour averaging of a locally two-dimensional Euler flow. We do not attempt here to solve the system exactly, but point out that non-existence of physically acceptable solutions would most probably be a result of the axial flow. Because of the axial flow the vorticity distribution within the dipole eddies is no longer of the simple Sadovskii type (vorticity constant over a cross-section) obtained in the axisymmetric problem. Thus the solution of the system depends upon the existence of a larger class of propagating two-dimensional dipoles. The hairpin model is obtained by formal asymptotic analysis. As in the axisymmetric problem a local transformation to ‘shrinking’ coordinates is introduced, but now in a self-similar form appropriate to the study of a possible finite-time singularity. We discuss some properties of the model, including a study of the helicity and a first step in iterating toward a solution from the Sadovskii structure. We also present examples of two-dimensional propagating dipoles not previously studied, which have a vorticity profile consistent with our model. Although no rigorous results can be given, and analysis of the system is only partial, the formal calculations are consistent with the possibility of a finite time blowup of vorticity at a point of vanishing circulation of the dipole eddies, but depending upon the existence of the necessary two-dimensional propagating dipole. Our results also suggest that conservation of kinetic energy as

RTO/RC ITER plasma performance: inductive and steady-state operation

International Nuclear Information System (INIS)

Mukhovatov, V.; Boucher, D.; Fujisawa, N.; Shimada, M.; Vayakis, G.; Janeschitz, G.; Matsumoto, H.; Leonov, V.; Polevoy, A.

2000-01-01

The plasma performance in two design options of the reduced-technical objectives/reduced cost (RTO/RC) ITER, i.e. IAM (intermediate aspect ratio machine) and LAM (low aspect ratio machine) is analysed. It is shown that Q=P fus /P aux ∼10 can be obtained in both options at inductively driven ELMy H-mode operation. The operation domain in LAM is found to be marginally larger than that in IAM. The non-inductive operation with Q approx.= 5 will be possible in both machines, provided a large amount of power with a high current drive efficiency is applied, or substantial improvement of the energy confinement time relative to the ELMy H-mode (H H =1.2-1.4) is obtained. The required values of H H and β N are marginally smaller in IAM. The IAM-like machine, ITER-FEAT (fusion energy advanced tokamak), proposed for a detailed engineering design is discussed in brief. (author)

Ultra-compact microwave filters using kinetic inductance microstrip

International Nuclear Information System (INIS)

Pond, J.M.; Carroll, K.R.; Cukauskas, E.J.

1991-01-01

This paper reports on multi-pole microwave filters designed and fabricated using microstrip transmission line sections which consist of two very thin films of sputtered niobium nitride (NbN) separated by another very thin film of sputtered Si. Since the thicknesses of all three films are much less than the superconducting penetration depth, the kinetic inductance is significantly greater than the magnetic inductance. As a result, the phase velocity of a microstrip transmission line is much less than the free space speed of light. Since resonant structures are reduced in size proportionately, the size and weight of microstrip circuits can be greatly reduced. Prototype filters consisting of four open circuit half-wavelength microstrip stubs separated by full-wavelength microstrip sections have been measured. The circuits are connected to 34 mil diameter coaxial cable via an intermediate coplanar waveguide section. Passbands of 4 GHz separated by 3 GHz reject bands have been measured in a structure which occupies less than 0.5 cm 2 including the coplanar waveguide transitions. Higher-order passbands, although possessing an increased insertion loss, maintain filter passband characteristics through 20.0 GHz

Practicing induction:

DEFF Research Database (Denmark)

Sprogøe, Jonas; Rohde, Nicolas

2009-01-01

We claim that induction potentially triggers both individual and organizational learning and by drawing on practice-based theory we discuss how the interplay between individual and organization, what we call a generative dance, ignites both kinds of learning.......We claim that induction potentially triggers both individual and organizational learning and by drawing on practice-based theory we discuss how the interplay between individual and organization, what we call a generative dance, ignites both kinds of learning....

Control System for Producing Electricity with Dual Stator Winding Cage-Rotor Induction Generator

Directory of Open Access Journals (Sweden)

Lucian Nicolae Tutelea

2014-09-01

Full Text Available This paper will present the key design equations and control design model of the Dual Stator Winding Cage-Rotor Induction Generator (DSWIG to achieve wide-speed-range operation with reduced capacity of the static power controller for low power wind or hydro applications. The proposed induction generator consists of a standard squirrel-cage rotor and a stator with two separate windings wound for a similar number of poles. Moreover, the system control strategy using the stator flux orientation is consequently proposed. The aim of the paper is to emphasize that the low speed induction generators with power electronic converters represent a realistic and useful solution for direct drive power applications.

Evaluating the influence of feedbacks between erosion rate and weathering on the distribution of erodibility in bedrock river channels

OpenAIRE

Shobe, Charles; Hancock, Gregory; Eppes, Martha; Small, Eric

2018-01-01

This is a poster presented on November 3rd, 2015 at the Geological Society of America annual meeting in Baltimore, MD, USA. The poster presents rock strength and roughness data from tributaries to the Potomac River in Virginia. Our data support the idea that bedrock channel erodibility is greater on the channel margins than at the thalweg, which we hypothesize to be the result of weathering damage preferentially accumulated on the channel banks. This work was published in Shobe et al (2017; E...

Microbial oxidation of lithospheric organic carbon in rapidly eroding tropical mountain soils.

Science.gov (United States)

Hemingway, Jordon D; Hilton, Robert G; Hovius, Niels; Eglinton, Timothy I; Haghipour, Negar; Wacker, Lukas; Chen, Meng-Chiang; Galy, Valier V

2018-04-13

Lithospheric organic carbon ("petrogenic"; OC petro ) is oxidized during exhumation and subsequent erosion of mountain ranges. This process is a considerable source of carbon dioxide (CO 2 ) to the atmosphere over geologic time scales, but the mechanisms that govern oxidation rates in mountain landscapes are poorly constrained. We demonstrate that, on average, 67 ± 11% of the OC petro initially present in bedrock exhumed from the tropical, rapidly eroding Central Range of Taiwan is oxidized in soils, leading to CO 2 emissions of 6.1 to 18.6 metric tons of carbon per square kilometer per year. The molecular and isotopic evolution of bulk OC and lipid biomarkers during soil formation reveals that OC petro remineralization is microbially mediated. Rapid oxidation in mountain soils drives CO 2 emission fluxes that increase with erosion rate, thereby counteracting CO 2 drawdown by silicate weathering and biospheric OC burial. Copyright © 2018 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

Ketoconazole attenuates radiation-induction of tumor necrosis factor

Energy Technology Data Exchange (ETDEWEB)

Hallahan, D.E.; Virudachalam, S.; Kufe, D.W.; Weichselbaum, R.R. [Dana Farber Cancer Institute, Boston, MA (United States)

1994-07-01

Previous work has demonstrated that inhibitors of phospholipase A2 attenuate ionizing radiation-induced arachidonic acid production, protein kinase C activation, and prevent subsequent induction of the tumor necrosis factor gene. Because arachidonic acid contributes to radiation-induced tumor necrosis factor expression, the authors analyzed the effects of agents which alter arachidonate metabolism on the regulation of this gene. Phospholipase A2 inhibitors quinicrine, bromphenyl bromide, and pentoxyfylline or the inhibitor of lipoxygenase (ketoconazole) or the inhibitor of cycloxygenase (indomethacine) were added to cell culture 1 h prior to irradiation. Radiation-induced tumor necrosis factor gene expression was attenuated by each of the phospholipase A2 inhibitors (quinicrine, bromphenylbromide, and pentoxyfylline). Furthermore, ketoconazole attenuated X ray induced tumor necrosis factor gene expression. Conversely, indomethacin enhanced tumor necrosis factor expression following irradiation. The finding that radiation-induced tumor necrosis factor gene expression was attenuated by ketoconazole suggests that the lipoxygenase pathway participates in signal transduction preceding tumor necrosis factor induction. Enhancement of tumor necrosis factor expression by indomethacin following irradiation suggests that prostaglandins produced by cyclooxygenase act as negative regulators of tumor necrosis factor expression. Inhibitors of tumor necrosis factor induction ameliorate acute and subacute sequelae of radiotherapy. The authors propose therefore, that ketoconazole may reduce acute radiation sequelae such as mucositis and esophagitis through a reduction in tumor necrosis factor induction or inhibition of phospholipase A2 in addition to its antifungal activity. 25 refs., 2 figs.

Fault Diagnosis of Low-Power Three-Phase Induction Motor

Directory of Open Access Journals (Sweden)

Gedzurs Aleksejs

2016-12-01

Full Text Available An Induction motor reliability survey at an egg processing plant shows that almost 50% of the total motor failures are fan induction motors. Visual investigations of the faulty fan motors show that the main cause of the induction motor failure is air gap eccentricity. In this study, experimental tests are performed on a 1.1kW three-phase induction motor to detect air gap eccentricity and overheating of the induction motor. Heating tests show that end shield housing temperature reaches 100°C with blocked air flow from the fan, which can reduce the lifespan of the bearing. Dimension measurements of the end shield housing show that the dimensions of both tested motors back-end shields are larger than ISO tolerance grade limit. It leads to a loose fit between the housing and bearing, causing air gap eccentricity. Also, both motor back end shield housing has an out-of-round condition leading to an unbalanced magnetic pull. To detect the air gap eccentricity caused by too loose of a fit between housing bore and bearing, current Park’s vector approach is used. To measure three phase current, Hall Effect current transducers, a digital oscilloscope is used and Matlab software to process the measurement data. Results show that Park’s vector approach can be used to detect the air gap eccentricity caused by too loose a fit between bearing and housing. Therefore, the Park’s vector approach can be used to diagnose air gap eccentricity and analyse the type of the air gap eccentricity.

Local and non-local effects of spanwise finite perturbations in erodible river bathymetries

Science.gov (United States)

Musa, Mirko; Hill, Craig; Guala, Michele

2015-11-01

Laboratory experiments were performed to study the effect of axial-flow hydrokinetic turbine models on an erodible river bed under live-bed conditions. Results indicate that the presence of an operating turbine rotor creates a blockage in the mean flow which produces a remarkable geomorphic signature in the migrating bedforms. These impacts affect a local area downstream of the turbines when placed symmetrically with respect to the cross section of the channel. On the other hand, more interesting results are observed with an asymmetric installation of the turbines. This configuration demonstrates a stronger effect on the mean flow, resulting in a larger plan-wise distortion of the mean topography and differential migration patterns of bedforms. Different turbine installation arrangements and hub heights above the mean bed were investigated, focusing mainly on the perturbation of sediment transport characteristics influenced by the turbine wake. Additional results with spanwise modulated submerged walls explore the possibility to control river topography harvesting this type of geomorphic destabilization.

Economic implications of labor induction.

Science.gov (United States)

Garcia-Simon, Raquel; Montañes, Antonio; Clemente, Jesús; Del Pino, María D; Romero, Manuel A; Fabre, Ernesto; Oros, Daniel

2016-04-01

To assess health service costs associated with labor induction according to different clinical situations in a tertiary-level hospital. In a prospective study, individual patient cost data were assessed for women admitted for induction of labor at a tertiary hospital in Spain between November 1, 2012, and August 31, 2013. The costs of labor induction were estimated according to maternal and neonatal outcomes, method of delivery, cervical condition at admission, and obstetric indication. Direct costs including professional fees, epidural, maternal stay, consumables, and drugs were calculated. Overall, 412 women were included in the final cost analysis. The mean total cost of labor induction was €3589.87 (95% confidence interval [CI] 3475.13-3704.61). Cesarean delivery after labor induction (€4830.45, 95% CI 4623.13-5037.58) was significantly more expensive than spontaneous delivery (€3037.45, 95% CI 2966.91-3179.99) and instrumental vaginal delivery (€3344.31, 95%CI 3151.69-3536.93). The total cost for patients with a very unfavorable cervix (Bishop score Labor induction for hypertensive disorders of pregnancy was the most expensive obstetric indication for induction of labor (€4347.32, 95% CI 3890.45-4804.18). Following the induction of labor, a number of patient- and treatment-related factors influence costs associated with delivery. Copyright © 2015 International Federation of Gynecology and Obstetrics. Published by Elsevier Ireland Ltd. All rights reserved.

SU-8 etching in inductively coupled oxygen plasma

DEFF Research Database (Denmark)

Rasmussen, Kristian Hagsted; Keller, Stephan Sylvest; Jensen, Flemming

2013-01-01

Structuring or removal of the epoxy based, photo sensitive polymer SU-8 by inductively coupled plasma reactive ion etching (ICP-RIE) was investigated as a function of plasma chemistry, bias power, temperature, and pressure. In a pure oxygen plasma, surface accumulation of antimony from the photo......-initiator introduced severe roughness and reduced etch rate significantly. Addition of SF6 to the plasma chemistry reduced the antimony surface concentration with lower roughness and higher etch rate as an outcome. Furthermore the etch anisotropy could be tuned by controlling the bias power. Etch rates up to 800 nm...

SOIL ERODIBILITY IN THE BRAZILIAN COASTAL PLAINS ERODIBILIDADE DO SOLO NOS TABULEIROS COSTEIROS

Directory of Open Access Journals (Sweden)

Nilton Curi

2011-07-01

Full Text Available

In order to determine soil losses caused by water erosion, in different situations, erosion prediction models, such as the Universal Soil Loss Equation (USLE, are used. Their application on agricultural and environmental planning depends on the determination of the USLE factors, including erodibility (K factor. The objective of this study was to determine erodibility for the main soil classes of the Brazilian Coastal Plains region, in Aracruz, Espírito Santo State. The experiment was established in the following soils: medium/clayey texture Yellow Argisol (PA1, Haplic Plinthosol (FX, and moderately rocky Yellow Argisol (PA2. For the calculation of soil erodibility, data of erosivity and soil losses, from November 1997 to May 2004, were used. Soil losses samplings were performed for each rainfall event regarded as erosive. The erodibility values were 0.007 Mg h MJ^-1 mm^-1

Inductive line energy storage generator

Energy Technology Data Exchange (ETDEWEB)

Choi, P [Ecole Polytechnique, Palaiseau (France). Laboratoire de Physique des Milieux Ionises

1997-12-31

The inductive energy storage (IES) generator has long been considered to be the most efficient system for energy usage in large pulsed power system at the MA level. A number of parameters govern the efficiency of energy transfer between the storage capacitors and the load, and the level of current deliverable to the load. For high power system, the energy storage capacitors are arranged as a Marx generator. The primary constraints are the inductances in the various parts of the circuit, in particular, the upstream inductance between the Marx and the POS, and the downstream inductance between the POS and the load. This paper deals with the effect of replacing part of the upstream inductance with a transmission line and introduces the new concept of an inductive line for energy storage (ILES). Extensive parametric scans were carried out on circuit simulations to investigate the effect of this upstream transmission line. A model was developed to explain the operation of the ILES design based on the data obtained. Comparison with an existing IES generator shows that the ILES design offers a significant improvement in the maximum current and hence energy delivered to an inductive load. (author). 5 figs., 1 ref.

Deficient induction response in a Xenopus nucleocytoplasmic hybrid.

Directory of Open Access Journals (Sweden)

Patrick Narbonne

2011-11-01

Full Text Available Incompatibilities between the nucleus and the cytoplasm of sufficiently distant species result in developmental arrest of hybrid and nucleocytoplasmic hybrid (cybrid embryos. Several hypotheses have been proposed to explain their lethality, including problems in embryonic genome activation (EGA and/or nucleo-mitochondrial interactions. However, conclusive identification of the causes underlying developmental defects of cybrid embryos is still lacking. We show here that while over 80% of both Xenopus laevis and Xenopus (Silurana tropicalis same-species androgenetic haploids develop to the swimming tadpole stage, the androgenetic cybrids formed by the combination of X. laevis egg cytoplasm and X. tropicalis sperm nucleus invariably fail to gastrulate properly and never reach the swimming tadpole stage. In spite of this arrest, these cybrids show quantitatively normal EGA and energy levels at the stage where their initial gastrulation defects are manifested. The nucleocytoplasmic incompatibility between these two species instead results from a combination of factors, including a reduced emission of induction signal from the vegetal half, a decreased sensitivity of animal cells to induction signals, and differences in a key embryonic protein (Xbra concentration between the two species, together leading to inefficient induction and defective convergence-extension during gastrulation. Indeed, increased exposure to induction signals and/or Xbra signalling partially rescues the induction response in animal explants and whole cybrid embryos. Altogether, our study demonstrates that the egg cytoplasm of one species may not support the development promoted by the nucleus of another species, even if this nucleus does not interfere with the cytoplasmic/maternal functions of the egg, while the egg cytoplasm is also capable of activating the genome of that nucleus. Instead, our results provide evidence that inefficient signalling and differences in the

Inductive Reasoning: A Training Approach

Science.gov (United States)

Klauer, Karl Josef; Phye, Gary D.

2008-01-01

Researchers have examined inductive reasoning to identify different cognitive processes when participants deal with inductive problems. This article presents a prescriptive theory of inductive reasoning that identifies cognitive processing using a procedural strategy for making comparisons. It is hypothesized that training in the use of the…

Simulated bat populations erode when exposed to climate change projections for western North America.

Directory of Open Access Journals (Sweden)

Mark A Hayes

Full Text Available Recent research has demonstrated that temperature and precipitation conditions correlate with successful reproduction in some insectivorous bat species that live in arid and semiarid regions, and that hot and dry conditions correlate with reduced lactation and reproductive output by females of some species. However, the potential long-term impacts of climate-induced reproductive declines on bat populations in western North America are not well understood. We combined results from long-term field monitoring and experiments in our study area with information on vital rates to develop stochastic age-structured population dynamics models and analyzed how simulated fringed myotis (Myotis thysanodes populations changed under projected future climate conditions in our study area near Boulder, Colorado (Boulder Models and throughout western North America (General Models. Each simulation consisted of an initial population of 2,000 females and an approximately stable age distribution at the beginning of the simulation. We allowed each population to be influenced by the mean annual temperature and annual precipitation for our study area and a generalized range-wide model projected through year 2086, for each of four carbon emission scenarios (representative concentration pathways RCP2.6, RCP4.5, RCP6.0, RCP8.5. Each population simulation was repeated 10,000 times. Of the 8 Boulder Model simulations, 1 increased (+29.10%, 3 stayed approximately stable (+2.45%, +0.05%, -0.03%, and 4 simulations decreased substantially (-44.10%, -44.70%, -44.95%, -78.85%. All General Model simulations for western North America decreased by >90% (-93.75%, -96.70%, -96.70%, -98.75%. These results suggest that a changing climate in western North America has the potential to quickly erode some forest bat populations including species of conservation concern, such as fringed myotis.

Inductive Monitoring System (IMS)

Data.gov (United States)

National Aeronautics and Space Administration — IMS: Inductive Monitoring System The Inductive Monitoring System (IMS) is a tool that uses a data mining technique called clustering to extract models of normal...

Reduced impact of induced gate noise on inductively degenerated LNAs in deep submicron CMOS technologies

DEFF Research Database (Denmark)

Rossi, P.; Svelto, F.; Mazzanti, A.

2005-01-01

Designers of radio-frequency inductively-degenerated CMOS low-noise-amplifiers have usually not followed the guidelines for achieving minimum noise figure. Nonetheless, state-of-the- art implementations display noise figure values very close to the theoretical minimum. In this paper, we point out...... that this is due to the effect of the parasitic overlap capacitances in the MOS device. In particular, we show that overlap capacitances lead to a significant induced-gate-noise reduction, especially when deep sub-micron CMOS processes are used....

Effect of inductance between middle and outer cylinders on diode voltage of pulse forming line

International Nuclear Information System (INIS)

Liu Jinliang; Wang Xinxin

2008-01-01

Based on the experimental device of the water spiral pulse forming line(PFL) type electron beam accelerator, the effect of inductance between the middle and outer cylinders of PFL on diode voltage is theoretically and experimentally studied in this paper. The formulae are introduced, with which the effect of inductance on diode voltage is calculated. In addition, the diode voltage waveform is simulated through the Pspice software. The theoretical and simulated results agree well with the experimental results, which show that large inductance between middle and outer cylinders can shorten the waveform flat part of diode voltage, increase waveform rise time and reduce the diode peak voltage. When the inductance is smaller than 200 nH, a nearly square voltage waveform can be obtained in field-emission diode. (authors)

Effect of Inductive Coil Shape on Sensing Performance of Linear Displacement Sensor Using Thin Inductive Coil and Pattern Guide

Directory of Open Access Journals (Sweden)

Hiroyuki Wakiwaka

2011-11-01

Full Text Available This paper discusses the effect of inductive coil shape on the sensing performance of a linear displacement sensor. The linear displacement sensor consists of a thin type inductive coil with a thin pattern guide, thus being suitable for tiny space applications. The position can be detected by measuring the inductance of the inductive coil. At each position due to the change in inductive coil area facing the pattern guide the value of inductance is different. Therefore, the objective of this research is to study various inductive coil pattern shapes and to propose the pattern that can achieve good sensing performance. Various shapes of meander, triangular type meander, square and circle shape with different turn number of inductive coils are examined in this study. The inductance is measured with the sensor sensitivity and linearity as a performance evaluation parameter of the sensor. In conclusion, each inductive coil shape has its own advantages and disadvantages. For instance, the circle shape inductive coil produces high sensitivity with a low linearity response. Meanwhile, the square shape inductive coil has a medium sensitivity with higher linearity.

Global model of instabilities in low-pressure inductively coupled chlorine plasmas

Science.gov (United States)

Despiau-Pujo, Emilie; Chabert, Pascal

2009-10-01

Experimental studies have shown that low-pressure inductive discharges operating with electronegative gases are subject to instabilities near the transition between capacitive (E) and inductive (H) modes. A global model, consisting of two particle balance equations and one energy balance equation, has been previously proposed to describe the instability mechanism in SF6/ArSF6 [1]. This model, which agrees qualitatively well with experimental observations, leaves significant quantitative differences. In this paper, the model is revisited with Cl2 as the feedstock gas. An alternative treatment of the inductive power deposition is evaluated and chlorine chemistry is included. Old and new models are systematically compared. The alternative inductive coupling description slightly modifies the results. The effect of gas chemistry is even more pronounced. The instability window is smaller in pressure and larger in absorbed power, the frequency is higher and the amplitudes of oscillations are reduced. The feedstock gas is weakly dissociated ( 16%) and Cl2^+ is the dominant positive ion, which is consistent with the moderate electron density during the instability cycle. [1] M.A. Lieberman, A.J. Lichtenberg, and A.M. Marakhtanov, Appl. Phys. Lett. 75 (1999) 3617

The use of a special software for induction motor diagnostics in the diamond industry

Directory of Open Access Journals (Sweden)

Shevchuk Vladislav A.

2017-01-01

Full Text Available The field of induction motor application in the diamond industry has considerably increased due to the transition to the underground mining method. This article is devoted to the research the induction motor diagnostic technique in the diamond industry using special software. The practice shows that unreliability of induction motors causes some serious economic losses related to the expenses on premature maintenance and idle time. This article is devoted to the research of diagnostic technique of induction motors in the diamond industry using a special software. The article presents some data obtained in the course of the research conducted at an industrial site of the diamond company “ALROSA” in Mirny using the vibration-based diagnostics. Thus, based on the analysis of the findings some recommendations concerning the improvement of maintenance and servicing system have been given. The use of these recommendations allows assessing the operational reliability of induction motors in the diamond industry, minimizing the risk of sudden failures and reducing the maintenance and repair expenses.

A Position Sensorless Control Method for SRM Based on Variation of Phase Inductance

Science.gov (United States)

Komatsuzaki, Akitomo; Miki, Ichiro

Switched reluctance motor (SRM) drives are suitable for variable speed industrial applications because of the simple structure and high-speed capability. However, it is necessary to detect the rotor position with a position sensor attached to the motor shaft. The use of the sensor increases the cost of the drive system and machine size, and furthermore the reliability of the system is reduced. Therefore, several approaches to eliminate the position sensor have already been reported. In this paper, a position sensorless control method based on the variation of the phase inductance is described. The phase inductance regularly varies with the rotor position. The SRM is controlled without the position sensor using the de-fluxing period and the phase inductance. The turn-off timing is determined by computing the difference of angle between the sampling point and the aligned point and the variation of angle during the de-fluxing period. In the magnetic saturation region, the phase inductance at the current when the effect of the saturation starts is computed and the sensorless control can be carried out using this inductance. Experimental results show that the SRM is well controlled without the position sensor using the proposed method.

Dose sparing of induction dose of propofol by fentanyl and butorphanol: A comparison based on entropy analysis

Directory of Open Access Journals (Sweden)

Jasleen Kaur

2013-01-01

Full Text Available Background: The induction dose of propofol is reduced with concomitant use of opioids as a result of a possible synergistic action. Aim and Objectives: The present study compared the effect of fentanyl and two doses of butorphanol pre-treatment on the induction dose of propofol, with specific emphasis on entropy. Methods: Three groups of 40 patients each, of the American Society of Anaesthesiologistsphysical status I and II, were randomized to receive fentanyl 2 μg/kg (Group F, butorphanol 20 μg/kg (Group B 20 or 40 μg/kg (Group B 40 as pre-treatment. Five minutes later, the degree of sedation was assessed by the observer′s assessment of alertness scale (OAA/S. Induction of anesthesia was done with propofol (30 mg/10 s till the loss of response to verbal commands. Thereafter, rocuronium 1 mg/kg was administered and endotracheal intubation was performed 2 min later. OAA/S, propofol induction dose, heart rate, blood pressure, oxygen saturation and entropy (response and state were compared in the three groups. Statistical Analysis: Data was analyzed using ANOVA test with posthoc significance, Kruskal-Wallis test, Chi-square test and Fischer exact test. A P<0.05 was considered as significant. Results: The induction dose of propofol (mg/kg was observed to be 1.1±0.50 in Group F, 1.05±0.35 in Group B 20 and 1.18±0.41 in Group B40. Induction with propofol occurred at higher entropy values on pre-treatment with both fentanyl as well as butorphanol. Hemodynamic variables were comparable in all the three groups. Conclusion: Butorphanol 20 μg/kg and 40 μg/kg reduce the induction requirement of propofol, comparable to that of fentanyl 2 μg/kg, and confer hemodynamic stability at induction and intubation.

Reduced-Capacity Inrush Current Suppressor Using a Matrix Converter in a Wind Power Generation System with Squirrel-Cage Induction Machines

Directory of Open Access Journals (Sweden)

Sho Shibata

2016-03-01

Full Text Available This paper describes the reduced capacity of the inrush current suppressor using a matrix converter (MC in a large-capacity wind power generation system (WPGS with two squirrel-cage induction machines (SCIMs. These SCIMs are switched over depending on the wind speed. The input side of the MC is connected to the source in parallel. The output side of the MC is connected in series with the SCIM through matching transformers. The modulation method of the MC used is direct duty ratio pulse width modulation. The reference output voltage of the MC is decided by multiplying the SCIM current with the variable control gain. Therefore, the MC performs as resistors for the inrush current. Digital computer simulation is implemented to confirm the validity and practicability of the proposed inrush current suppressor using PSCAD/EMTDC (power system computer-aided design/electromagnetic transients including DC. Furthermore, the equivalent resistance of the MC is decided by the relationship between the equivalent resistance and the capacity of the MC. Simulation results demonstrate that the proposed inrush current suppressor can suppress the inrush current perfectly.

An Analog-Digital Mixed Measurement Method of Inductive Proximity Sensor

Directory of Open Access Journals (Sweden)

Yi-Xin Guo

2015-12-01

Full Text Available Inductive proximity sensors (IPSs are widely used in position detection given their unique advantages. To address the problem of temperature drift, this paper presents an analog-digital mixed measurement method based on the two-dimensional look-up table. The inductance and resistance components can be separated by processing the measurement data, thus reducing temperature drift and generating quantitative outputs. This study establishes and implements a two-dimensional look-up table that reduces the online computational complexity through structural modeling and by conducting an IPS operating principle analysis. This table is effectively compressed by considering the distribution characteristics of the sample data, thus simplifying the processing circuit. Moreover, power consumption is reduced. A real-time, built-in self-test (BIST function is also designed and achieved by analyzing abnormal sample data. Experiment results show that the proposed method obtains the advantages of both analog and digital measurements, which are stable, reliable, and taken in real time, without the use of floating-point arithmetic and process-control-based components. The quantitative output of displacement measurement accelerates and stabilizes the system control and detection process. The method is particularly suitable for meeting the high-performance requirements of the aviation and aerospace fields.

Preoperative parental information and parents' presence at induction of anaesthesia.

Science.gov (United States)

Astuto, M; Rosano, G; Rizzo, G; Disma, N; Raciti, L; Sciuto, O

2006-06-01

Preoperative preparation of paediatric patients and their environment in order to prevent anxiety is an important issue in paediatric anaesthesia. Anxiety in paediatric patients may lead to immediate negative postoperative responses. When a child undergoes surgery, information about the child's anaesthesia must be provided to parents who are responsible for making informed choices about healthcare on their child's behalf. A combination of written, pictorial, and verbal information would improve the process of informed consent. The issue of parental presence during induction of anaesthesia has been a controversial topic for many years. Potential benefits from parental presence at induction include reducing or avoiding the fear and anxiety that might occur in both the child and its parents, reducing the need for preoperative sedatives, and improving the child's compliance even if other studies showed no effects on the anxiety and satisfaction level. The presence of other figures such as clowns in the operating room, together with one of the child's parents, is an effective intervention for managing child and parent anxiety during the preoperative period.

Segmented motor drive - with multi-phase induction motor

DEFF Research Database (Denmark)

Bendixen, Flemming Buus

of the induction motor is set up. The model is able to calculate dynamical electric, magnetic and mechanic state variables, but initially it is used to calculate static characteristics in motors with different number of phases and different voltage supply shapes. This analysis show i.e. that the efficiency....... The multi-phase motor is selected for further analysis. The project is limited to examine if increasing the number of phases can improve the characteristics for induction motor drives. In the literature it is demonstrated that torque production in a six-phase motor can be increased, if a 3rd harmonic......This PhD project commences in modulation of motor drives, i.e. having the advantage of reducing the number of variants and improves the system reliability at error situations. Four different motor drive topologies with modular construction as common denominator are compared on a general level...

CHUVAS, EROSIVIDADE, ERODIBILIDADE, USO DO SOLO E SUAS RELAÇÕES COM FOCOS EROSIVOS LINEARES NA ALTA BACIA DO RIO ARAGUAIA / Rainfall, erosivity, erodibility, land use and their relationships with erosion sites in the upper Araguaia River Basin

Directory of Open Access Journals (Sweden)

Silvando Carlos da Silva

2007-12-01

Full Text Available The intensive process of land occupation by farmers in the tropical savanna region of MidwestBrazil during the last three decades has promoted several environment impacts, such as theoccurrence of gully erosion processes as a consequence of intensive deforestation. Just in theUpper Araguaia River Basin, it was identified more than 300 large and medium gully features,which are related with the high natural susceptibility of the sandy soils; high erosivity and erodibility; inadequate land-use; lack of soil conservation practices; and a high annual rainfallindex during the rainy season. The objective of this research was to identify spatial relationshipsbetween rainfall distribution, erosivity, erodibility, land-use, and gully erosion distribution,which may support environmental planning actions related to land use conservation.Quantitative results show a high correlation between gully erosion distribution and higherosivity/erodibility and inadequate land-use.

Urofollitropin and ovulation induction

NARCIS (Netherlands)

van Wely, Madelon; Yding Andersen, Claus; Bayram, Neriman; van der Veen, Fulco

2005-01-01

Anovulation is a common cause of female infertility. Treatment for women with anovulation is aimed at induction of ovulation. Ovulation induction with follicle-stimulating hormone (FSH) is indicated in women with WHO type II anovulation in whom treatment with clomifene citrate (clomifene) has

Symbolic Solution Approach to Wind Turbine based on Doubly Fed Induction Generator Model

DEFF Research Database (Denmark)

Cañas–Carretón, M.; Gómez–Lázaro, E.; Martín–Martínez, S.

2015-01-01

–order induction generator is selected to model the electric machine, being this approach suitable to estimate the DFIG performance under transient conditions. The corresponding non–linear integro-differential equation system has been reduced to a linear state-space system by using an ad-hoc local linearization......This paper describes an alternative approach based on symbolic computations to simulate wind turbines equipped with Doubly–Fed Induction Generator (DFIG). The actuator disk theory is used to represent the aerodynamic part, and the one-mass model simulates the mechanical part. The 5th...

Reduced Sleep During Social Isolation Leads to Cellular Stress and Induction of the Unfolded Protein Response.

Science.gov (United States)

Brown, Marishka K; Strus, Ewa; Naidoo, Nirinjini

2017-07-01

Social isolation has a multitude of negative consequences on human health including the ability to endure challenges to the immune system, sleep amount and efficiency, and general morbidity and mortality. These adverse health outcomes are conserved in other social species. In the fruit fly Drosophila melanogaster, social isolation leads to increased aggression, impaired memory, and reduced amounts of daytime sleep. There is a correlation between molecules affected by social isolation and those implicated in sleep in Drosophila. We previously demonstrated that acute sleep loss in flies and mice induced the unfolded protein response (UPR), an adaptive signaling pathway. One mechanism indicating UPR upregulation is elevated levels of the endoplasmic reticular chaperone BiP/GRP78. We previously showed that BiP overexpression in Drosophila led to increased sleep rebound. Increased rebound sleep has also been demonstrated in socially isolated (SI) flies. D. melanogaster were used to study the effect of social isolation on cellular stress. SI flies displayed an increase in UPR markers; there were higher BiP levels, increased phosphorylation of the translation initiation factor eIF2α, and increased splicing of xbp1. These are all indicators of UPR activation. In addition, the effects of isolation on the UPR were reversible; pharmacologically and genetically altering sleep in the flies modulated the UPR. The reduction in sleep observed in SI flies is a cellular stressor that results in UPR induction. © Sleep Research Society 2017. Published by Oxford University Press [on behalf of the Sleep Research Society]. All rights reserved. For permissions, please email: journals.permissions@oup.com

Induction immunosuppressive therapies in renal transplantation.

Science.gov (United States)

Gabardi, Steven; Martin, Spencer T; Roberts, Keri L; Grafals, Monica

2011-02-01

Induction immunosuppressive therapies for patients undergoing renal transplantation are reviewed. The goal of induction therapy is to prevent acute rejection during the early posttransplantation period by providing a high degree of immunosuppression at the time of transplantation. Induction therapy is often considered essential to optimize outcomes, particularly in patients at high risk for poor short-term outcomes. All of the induction immunosuppressive agents currently used are biological agents and are either monoclonal (muromonab-CD3, daclizumab, basiliximab, alemtuzumab) or polyclonal (antithymocyte globulin [equine] or antithymocyte globulin [rabbit]) antibodies. Although antithymocyte globulin (rabbit) is not labeled for induction therapy, it is used for this purpose more than any other agent. Basiliximab is not considered as potent an immunosuppressive agent but has a much more favorable adverse-effect profile compared with antithymocyte globulin (rabbit) and is most commonly used in patients at low risk for acute rejection. Rituximab is being studied for use as induction therapy but to date has not demonstrated any significant benefits over placebo. While head-to-head data are available comparing most induction agents, the final decision on the most appropriate induction therapy for a transplant recipient is highly dependent on preexisting medical conditions, donor characteristics, and the maintenance immunosuppressive regimen to be used. No standard induction immunosuppressive regimen exists for patients undergoing renal transplantation. Antithymocyte globulin (rabbit) is the most commonly used agent, whereas basiliximab appears safer. The choice of regimen depends on the preferences of clinicians and institutions.

A Philosophical Treatise of Universal Induction

Directory of Open Access Journals (Sweden)

Samuel Rathmanner

2011-06-01

Full Text Available Understanding inductive reasoning is a problem that has engaged mankind for thousands of years. This problem is relevant to a wide range of fields and is integral to the philosophy of science. It has been tackled by many great minds ranging from philosophers to scientists to mathematicians, and more recently computer scientists. In this article we argue the case for Solomonoff Induction, a formal inductive framework which combines algorithmic information theory with the Bayesian framework. Although it achieves excellent theoretical results and is based on solid philosophical foundations, the requisite technical knowledge necessary for understanding this framework has caused it to remain largely unknown and unappreciated in the wider scientific community. The main contribution of this article is to convey Solomonoff induction and its related concepts in a generally accessible form with the aim of bridging this current technical gap. In the process we examine the major historical contributions that have led to the formulation of Solomonoff Induction as well as criticisms of Solomonoff and induction in general. In particular we examine how Solomonoff induction addresses many issues that have plagued other inductive systems, such as the black ravens paradox and the confirmation problem, and compare this approach with other recent approaches.

Review of induction LINACS

International Nuclear Information System (INIS)

Faltens, A.; Keefe, D.

1981-10-01

There has been a recent upsurge of activity in the field of induction linacs, with several new machines becoming operational and others in the design stages. The performance levels of electron machines have reached 10's of kiloamps of current and will soon reach 10's of MeV's of energy. Acceleration of ion current has been demonstrated, and the study of a 10 GeV heavy ion induction linac for ICF continues. The operating principles of induction linacs are reviewed with the emphasis on design choices which are important for increasing the maximum beam currents

Properties of inductive reasoning.

Science.gov (United States)

Heit, E

2000-12-01

This paper reviews the main psychological phenomena of inductive reasoning, covering 25 years of experimental and model-based research, in particular addressing four questions. First, what makes a case or event generalizable to other cases? Second, what makes a set of cases generalizable? Third, what makes a property or predicate projectable? Fourth, how do psychological models of induction address these results? The key results in inductive reasoning are outlined, and several recent models, including a new Bayesian account, are evaluated with respect to these results. In addition, future directions for experimental and model-based work are proposed.

Review of induction linacs

International Nuclear Information System (INIS)

Faltens, A.; Keefe, D.

1982-01-01

There has been a recent upsurge of activity in the field of induction linacs, with several new machines becoming operational and others in the design stages. The performance levels of electron machines have reached 10's of kiloamps of current and will soon reach 10's of MeV's of energy. Acceleration of several kiloamps of ion current has been demonstrated, and the study of a 10 GeV heavy ion induction linac for ICF continues. The operating principles of induction linacs are reviewed with the emphasis on design choices which are important for increasing the maximum beam currents

Induction generator-induction motor wind-powered pumping system

Energy Technology Data Exchange (ETDEWEB)

Miranda, M.S.; Lyra, R.O.C.; Silva, S.R. [CPDEE - UFMG, Belo Horizonte (Brazil)

1997-12-31

The energy storage matter plays an important role in wind-electric conversion systems for isolated applications. Having that in mind, two different approaches can be basically considered: either the immediate conversion of the generated electric energy, as in a water pumping system or electric energy storage for later use, as in a battery charging system. Due to some features such as no need of an external reactive power source and, sometimes, a gearbox, permanent-magnet synchronous generators have been broadly used in low rated power isolated systems. Despite that, system performance can be affected when the generator is feeding an inductive load (e.g., an induction motor) under variable-speed-variable-frequency operational conditions. Since there is no effective flux control, motor overload may occur at high wind speeds. Thus, good system performance can be obtained through additional control devices which may increase system cost. Although being rugged and cheap, induction machines always work as a reactive power drain; therefore, they demand an external reactive power source. Considering that, reactive static compensators appear as an attractive alternative to the cost x performance problem. In addition to that, different control strategies can be used so that system performance can be improved.

Regulation of ATM induction

International Nuclear Information System (INIS)

Clarke, R.A.; Fang, Z.M.; Kearsley, J.H.; Lee, C.S.; Sarris, M.; De Murrell, D.

2000-01-01

Full text: ATM, the tumour suppressor protein mutated in ataxia-telangiectasia, is of pivotal importance in controlling the cells primary response to ionising radiation (IR) induced DNA damage. Mutations in ATM which reduce the level of the ATM protein and/or compromise ATM functions are known to give rise to radiosensitivity and defective cell cycle checkpoint control. In response to DNA damage ATM kinase is rapidly activated and initiates downstream signalling to cell cycle control molecules including p53. To investigate additional mechanisms of ATM control we have employed ATM antisense expression in cultured cells, western analyses and immunohistochemistry in situ. We report that ATM can be up-regulated up to 10-fold following exposure to low levels of ionising radiation. ATM radiation-induction was radiation dose dependent while the rapidity of the response indicates a post translational pathway. The concurrent time frames for the radiation-induction of ATM levels and the activation of ATM kinase activity appear to be complimentary in boosting ATM's protective response to IR induced DNA damage, especially in ATM 'low expressing' systems. We also provide the first report of ATM misregulation in 2 cancer patients, indicating that ATM is not only radio-protective but has possible implications in cancer, particularly breast cancer. These results have particular importance in defining the regulation of the ATM protein as an: adaptive radio-response; radio-prognostic market in tumours and normal tissue, and breast cancer marker

Two-Phase Induction Motor Drives

Directory of Open Access Journals (Sweden)

Gholam Reza Arab Markadeh

2010-10-01

Full Text Available The lack of variable-speed drives for two (single induction motor is a reality. This article attempts mainly to investigate the reasons for this lack of variable – speed drives. This paper deals with literature survey of various existing converter topologies, which have been proposed for adjustable speed single phase induction motor drives. Various converter topologies have been compared in this paper. Among these converter topologies, the adjustable frequency PWM inverter is the best choice for single-phase induction motor drives. However, adjustable-frequency drives have not been widely used with single-phase Induction motors. The open-loop constant V/F control law cannot be used with the single-phase induction motor drives as it is used with three phase motors. The variation of the operating frequency at lower speed range with constant load torque causes variation in motor's slip. A constant V/F control is suitable only over the upper speed range.

CFOA-Based Lossless and Lossy Inductance Simulators

Directory of Open Access Journals (Sweden)

F. Kaçar

2011-09-01

Full Text Available Inductance simulator is a useful component in the circuit synthesis theory especially for analog signal processing applications such as filter, chaotic oscillator design, analog phase shifters and cancellation of parasitic element. In this study, new four inductance simulator topologies employing a single current feedback operational amplifier are presented. The presented topologies require few passive components. The first topology is intended for negative inductance simulation, the second topology is for lossy series inductance, the third one is for lossy parallel inductance and the fourth topology is for negative parallel (-R (-L (-C simulation. The performance of the proposed CFOA based inductance simulators is demonstrated on both a second-order low-pass filter and inductance cancellation circuit. PSPICE simulations are given to verify the theoretical analysis.

Induction sensor for measuring the accelerating voltage in an iron-free induction accelerator

International Nuclear Information System (INIS)

Bol'nykh, N.S.; Il'in, Yu.M.; Kostyushok, A.A.; Suvorov, V.A.

1987-01-01

An inductive sensor is described for measuring the amplitude and form of the accelerating-voltage pulse in the storage coils in a radial iron-free linear induction accelerator. The sensor does not respond to interference from external fields and does not require adjustment after calibration

Low-temperature thermal decomposition of dioxin-like compounds in fly ash: combination of chemical analysis with in vitro bioassays (EROD and DR-CALUX).

Science.gov (United States)

Behnisch, Peter A; Hosoe, Kazunori; Shiozaki, Ken; Ozaki, Hironori; Nakamura, Kazuo; Sakai, Shin-Ichi

2002-12-01

To investigate the dechlorination of fly ash during low-temperature treatment under oxygen-deficient conditions (thermocatalyic treatment or Hagenmaier process), six fly ash samples from six different incineration plants were treated in a laboratory experiment or in the actual plant, either under ideal (400 degrees C, 120 min) or intermediate (300 degrees C, 30 min) conditions. The aim of the present study was to confirm the decrease in the I-TEQ (international toxicity equivalency) of polychlorinated dibenzo-p-dioxins/-furans (PCDD/Fs) and coplanar polychlorinated biphenyls (co-PXBs) and, also for the first time, the decrease in the sum of dioxin-like toxicity (bioassay- or bio-TEQ) of all kinds of other dioxin-like Ah receptor agonists (such as PXDD/Fs, PXBs, PXN, X = Br, F) measured by two state-of-the-art cell-based Ah receptor-dependent bioassays: H4IIE-Ethoxy-Resorufin-o-Deethylase (EROD) and H4IIE-luc/DR-Chemical Activated Luciferase expression (DR-CALUX). The treatment efficiency was calculated on the basis of the reduction in the I-TEQ and bio-TED values. For these fly ash samples, the treatment efficiency, as measured by chemical analysis, was higher than 99%, and 85%-99%, in the case of the bio-TED values, indicating that these Ah receptor binding toxic compounds were sufficiently decomposed. Bio-TEQ values for untreated fly ash samples (n = 6) were on average 1.2 times (range 0.7-1.9), for the H4IIE-EROD assay, and 2.8 times (1.1-4.9), for the DR-CALUX assay, higher than I-TEQ values measured by chemical analyses (sum of PCDD/Fs and co-PCBs). In the case of these fly ash samples treated under ideal conditions and therefore low in contaminants, the bio-TEQ values were on average 1.4 times (range 0.9-1.8), for the H4IIE-EROD assay, and 5.1 times (range 1.2-12), for the DR-CALUX assay, higher than the I-TEQ values.

The induction on a continuous variable

International Nuclear Information System (INIS)

Zhang Jingzhong.

1989-06-01

Mathematical induction is a useful tool. But it could be used to prove only the proposition with form P(n) for the natural number n. Could the natural number n be replaced by a continuous variable x? Yes, and then we have the continuous induction. The continuous induction is very easy to grasp by the students who have learned mathematical induction. And it can be used to prove many basic propositions in the elementary calculus. (author)

Decreased term and postterm birthweight in the United States: impact of labor induction.

Science.gov (United States)

Zhang, Xun; Joseph, K S; Kramer, Michael S

2010-08-01

We sought to assess recent trends in falling mean birthweight (BW) and gestational age (GA) among US non-Hispanic white singleton live births >or=37 weeks of gestation and the contribution of increased rates of induction to these trends. This was an ecological study based on US vital statistics from 1992 through 2003. From 1992 through 2003, mean BW fell by 37 g, mean GA by 3 days, and macrosomia rates by 25%. Rates of induction nearly doubled from 14% to 27%. Our ecological state-level analysis showed that the increased rate of induction was significantly associated with reduced mean BW (r = -0.54; 95% confidence interval [CI], -0.71 to -0.29), mean GA (r = -0.44; 95% CI, -0.65 to -0.17), and rate of macrosomia (r = -0.55; 95% CI, -0.74 to -0.32). Increasing use of induction is a likely cause of the observed recent declines in BW and GA. The impact of these trends on infant and long-term health warrants attention and investigation. Copyright (c) 2010 Mosby, Inc. All rights reserved.

Arterial oxygen partial pressures reduce the insulin-dependent induction of the perivenously located glucokinase in rat hepatocyte cultures: mimicry of arterial oxygen pressures by H2O2.

OpenAIRE

Kietzmann, T; Roth, U; Freimann, S; Jungermann, K

1997-01-01

Liver glucokinase (GK) is localized predominantly in the perivenous zone. GK mRNA was induced by insulin maximally under venous O2 partial pressure (pO2) and only half-maximally under arterial pO2. CoCl2 and desferrioxamine mimicked venous pO2 and enhanced the insulin-dependent induction of GK mRNA under arterial pO2. H2O2 mimicked arterial pO2 and reduced insulin-induced GK mRNA under venous pO2 to the lower arterial levels. Thus the zonal O2 gradient in liver seems to have a key role in the...

Resveratrol attenuates methylglyoxal-induced mitochondrial dysfunction and apoptosis by Sestrin2 induction

Energy Technology Data Exchange (ETDEWEB)

Seo, Kyuhwa; Seo, Suho; Han, Jae Yun; Ki, Sung Hwan; Shin, Sang Mi, E-mail: smshin@chosun.ac.kr

2014-10-15

Methylglyoxal is found in high levels in the blood and other tissues of diabetic patients and exerts deleterious effects on cells and tissues. Previously, we reported that resveratrol, a polyphenol in grapes, induced the expression of Sestrin2 (SESN2), a novel antioxidant protein, and inhibited hepatic lipogenesis. This study investigated whether resveratrol protects cells from the methylglyoxal-induced toxicity via SESN2 induction. Methylglyoxal significantly induced cell death in HepG2 cells. However, cells pretreated with resveratrol were rescued from methylglyoxal-induced apoptosis. Resveratrol attenuated glutathione (GSH) depletion and ROS production promoted by methylglyoxal. Moreover, mitochondrial damage was observed by methylglyoxal treatment, but resveratrol restored mitochondrial function, as evidenced by the observed lack of mitochondrial permeability transition and increased ADP/ATP ratio. Resveratrol treatment inhibited SESN2 depletion elicited by methylglyoxal. SESN2 overexpression repressed methylglyoxal-induced mitochondrial dysfunction and apoptosis. Likewise, rotenone-induced cytotoxicity was not observed in SESN2 overexpressed cells. Furthermore, siRNA knockdown of SESN2 reduced the ability of resveratrol to prevent methylglyoxal-induced mitochondrial permeability transition. In addition, when mice were exposed to methylglyoxal after infection of Ad-SESN2, the plasma levels of alanine aminotransferase (ALT) and aspartate aminotransferase (AST) and GSH depletion by methylglyoxal in liver was reduced in Ad-SESN2 infected mice. Our results demonstrated that resveratrol is capable of protecting cells from methylglyoxal-induced mitochondrial dysfunction and oxidative stress via SESN2 induction. - Highlights: • Resveratrol decreased methylglyoxal-induced apoptosis. • Resveratrol attenuated GSH depletion and ROS production promoted by methylglyoxal. • Resveratrol restored the mitochondrial function by Sestrin2 induction. • Induction of Sestrin2

Resveratrol attenuates methylglyoxal-induced mitochondrial dysfunction and apoptosis by Sestrin2 induction

International Nuclear Information System (INIS)

Seo, Kyuhwa; Seo, Suho; Han, Jae Yun; Ki, Sung Hwan; Shin, Sang Mi

2014-01-01

Methylglyoxal is found in high levels in the blood and other tissues of diabetic patients and exerts deleterious effects on cells and tissues. Previously, we reported that resveratrol, a polyphenol in grapes, induced the expression of Sestrin2 (SESN2), a novel antioxidant protein, and inhibited hepatic lipogenesis. This study investigated whether resveratrol protects cells from the methylglyoxal-induced toxicity via SESN2 induction. Methylglyoxal significantly induced cell death in HepG2 cells. However, cells pretreated with resveratrol were rescued from methylglyoxal-induced apoptosis. Resveratrol attenuated glutathione (GSH) depletion and ROS production promoted by methylglyoxal. Moreover, mitochondrial damage was observed by methylglyoxal treatment, but resveratrol restored mitochondrial function, as evidenced by the observed lack of mitochondrial permeability transition and increased ADP/ATP ratio. Resveratrol treatment inhibited SESN2 depletion elicited by methylglyoxal. SESN2 overexpression repressed methylglyoxal-induced mitochondrial dysfunction and apoptosis. Likewise, rotenone-induced cytotoxicity was not observed in SESN2 overexpressed cells. Furthermore, siRNA knockdown of SESN2 reduced the ability of resveratrol to prevent methylglyoxal-induced mitochondrial permeability transition. In addition, when mice were exposed to methylglyoxal after infection of Ad-SESN2, the plasma levels of alanine aminotransferase (ALT) and aspartate aminotransferase (AST) and GSH depletion by methylglyoxal in liver was reduced in Ad-SESN2 infected mice. Our results demonstrated that resveratrol is capable of protecting cells from methylglyoxal-induced mitochondrial dysfunction and oxidative stress via SESN2 induction. - Highlights: • Resveratrol decreased methylglyoxal-induced apoptosis. • Resveratrol attenuated GSH depletion and ROS production promoted by methylglyoxal. • Resveratrol restored the mitochondrial function by Sestrin2 induction. • Induction of Sestrin2

Tritium recycling and inventory in eroded debris of plasma-facing materials

International Nuclear Information System (INIS)

Hassanein, A.

1999-01-01

Damage to plasma-facing components (PFCs) and structural materials due to loss of plasma confinement in magnetic fusion reactors remains one of the most serious concerns for safe, successful, and reliable tokamak operation. High erosion losses due to surface vaporization, spallation, and melt-layer splashing are expected during such an event. The eroded debris and dust of the PFCs, including trapped tritium, will be contained on the walls or within the reactor chamber therefore, they can significantly influence plasma behavior and tritium inventory during subsequent operations. Tritium containment and behavior in PFCS and in the dust and debris is an important factor in evaluating and choosing the ideal plasma-facing materials (PFMs). Tritium buildup and release in the debris of candidate materials is influenced by the effect of material porosity on diffusion and retention processes. These processes have strong nonlinear behavior due to temperature, volubility, and existing trap sites. A realistic model must therefore account for the nonlinear and multidimensional effects of tritium diffusion in the porous-redeposited and neutron-irradiated materials. A tritium-transport computer model, TRAPS (Tritium Accumulation in Porous Structure), was developed and used to evaluate and predict the kinetics of tritium transport in porous media. This model is coupled with the TRICS (Tritium In Compound Systems) code that was developed to study the effect of surface erosion during normal and abnormal operations on tritium behavior in PFCS

Low-pressure water-cooled inductively coupled plasma torch

Science.gov (United States)

Seliskar, Carl J.; Warner, David K.

1988-12-27

An inductively coupled plasma torch is provided which comprises an inner tube, including a sample injection port to which the sample to be tested is supplied and comprising an enlarged central portion in which the plasma flame is confined; an outer tube surrounding the inner tube and containing water therein for cooling the inner tube, the outer tube including a water inlet port to which water is supplied and a water outlet port spaced from the water inlet port and from which water is removed after flowing through the outer tube; and an r.f. induction coil for inducing the plasma in the gas passing into the tube through the sample injection port. The sample injection port comprises a capillary tube including a reduced diameter orifice, projecting into the lower end of the inner tube. The water inlet is located at the lower end of the outer tube and the r.f. heating coil is disposed around the outer tube above and adjacent to the water inlet.

Development of induction cells at CAEP

International Nuclear Information System (INIS)

Wang Huacen; Zhang Kaizhi; Cheng Nian'an; Zhang Wenwei; Lai Qinggui; Wen Long; Zhang Linwen; Deng Jianjun; Ding Bonan

2002-01-01

The effects to develop induction cells for induction linac and radiography at CAEP are introduced and reviewed in this paper. During the past two decades, several kinds of cells have been designed and tested, and some of them have been used for construction of induction linac, such as Dragon-1 and 12 MeV, and a Synthetic Test Stand (STS) for comprehensive linac technology study. The structure, test results and performance in the induction linac of these cells are given

Linear induction accelerator

Science.gov (United States)

Buttram, M.T.; Ginn, J.W.

1988-06-21

A linear induction accelerator includes a plurality of adder cavities arranged in a series and provided in a structure which is evacuated so that a vacuum inductance is provided between each adder cavity and the structure. An energy storage system for the adder cavities includes a pulsed current source and a respective plurality of bipolar converting networks connected thereto. The bipolar high-voltage, high-repetition-rate square pulse train sets and resets the cavities. 4 figs.

Model of Transient Process Where Three-Phase Transducer Feeds Induction Motor Equivalent as a Variable Active-Inductive Load

Directory of Open Access Journals (Sweden)

Nenad Marković

2016-01-01

Full Text Available The paper presents a new approach in the analysis of a transient state in a system where the feeding source is a transducer-IGBT inverter and load is introduced through the induction motor with its R-L parameters. Induction motors with different parameters of powers and power factors are tested. MATLAB simulation of the three-phase inverter that feeds the induction machine has replaced the missing lab equipment with which mathematical model of this system was verified. According to the selected parameters of the inverter and induction machine and through the simulation in the MATLAB program, the results are obtained in the form of diagrams that verify the model of a transient state of the induction machine operation when it operates as a motor which is presented as a variable R-L load. The transient process of the system three-phase bridge inverter whose active-inductive load is the induction machine in the conditions of the change of the load parameters is analyzed. The model of the transient process in the system formed by the inverter in PWM (Pulse Width Modulation converter and induction machine is developed in the time domain and phase coordinates.

Restoring crop productivity of eroded lands through , integrated plant nutrient management (IPNM) for sustained production

International Nuclear Information System (INIS)

Bhatti, A.U.; Ali, S.

2005-01-01

Crop productivity of eroded lands is very poor due to removal of top fertile soil losing organic matter and plant nutrients, with consequent exposure of the sub-soil with poor fertility status. Crop productivity of such lands needs to be restored in order to help farmers feed many mouths because of increased population and high land pressure. Three field experiments were laid out at three sites, Thana, Malakand Agency; Kabal and Matta, Swat during 2003-2004 to study the effect of integrated plant nutrient management on the yield of wheat. The fertilizer treatments consisted of farmer's practice (60-45-0 kg N-P/sub 2/O/sub 5/-K/sub 2/O ha/sup -1/), recommended fertilizer rate (120-90-60 kg N-P/sub 2/O/sub 5/-K/sub 2/O ha/sup -l/ + 5 kg Zn ha/sup -1), and combined application of organic and inorganic sources of plant nutrients (FYM at the rate of 20 t ha/sup -1/ plus 60-90-60 kg N-P/sub 2/O/sub 5/-K/sub 2/O ha/sup -1/ + 5 kg Zn ha/sup -1/). The results obtained from these field trails showed that the combined application of FYM with NPK Zn increased the grain yield significantly over the other two treatments with an increase of 50-80% over the farmer's practice and 11 to 23 % over the recommended dose. As regards straw yields, T/sub 2/ and T/sub 3/ increased the yields significantly over farmer's practice (T) at all the sites; However, T/sub 2/ and T/sub 3/ at Thana and Kabal were at par with each other. As regards effect of various treatments on soil properties, organic matter content was improved at Thana and Kabal sites while at Matta the results were inconsistent. Similarly soil P and Zn contents were increased considerably in T/sub 2/ and T/sub 3/ at Thana and Kabal being at par with each other. It is apparent from these results that the crop productivity of eroded lands at all the three sties was considerably restored and the soil fertility status was improved by integrated plant nutrient management. (author)

Wind-Eroded Crater Floors and Intercrater Plains, Terra Sabaea, Mars

Science.gov (United States)

Irwin, Rossman P.; Wray, James J.; Mest, Scott C.; Maxwell, Ted A.

2018-02-01

Ancient impact craters with wind-eroded layering on their floors provide a record of resurfacing materials and processes on early Mars. In a 54 km Noachian crater in Terra Sabaea (20.2°S, 42.6°E), eolian deflation of a friable, dark-toned layer up to tens of meters thick has exposed more resistant, underlying light-toned material. These layers differ significantly from strata of similar tone described in other regions of Mars. The light-toned material has no apparent internal stratification, and visible/near-infrared spectral analysis suggests that it is rich in feldspar. Its origin is ambiguous, as we cannot confidently reject igneous, pyroclastic, or clastic alternatives. The overlying dark-toned layer is probably a basaltic siltstone or sandstone that was emplaced mostly by wind, although its weak cementation and inverted fluvial paleochannels indicate some modification by water. Negative-relief channels are not found on the crater floor, and fluvial erosion is otherwise weakly expressed in the study area. Small impacts onto this crater's floor have exposed deeper friable materials that appear to contain goethite. Bedrock outcrops on the crater walls are phyllosilicate bearing. The intercrater plains contain remnants of a post-Noachian thin, widespread, likely eolian mantle with an indurated surface. Plains near Hellas-concentric escarpments to the north are more consistent with volcanic resurfacing. A 48 km crater nearby contains similar dark-over-light outcrops but no paleochannels. Our findings indicate that dark-over-light stratigraphy has diverse origins across Mars and that some dark-toned plains with mafic mineralogy are not of igneous origin.

Structured Statistical Models of Inductive Reasoning

Science.gov (United States)

Kemp, Charles; Tenenbaum, Joshua B.

2009-01-01

Everyday inductive inferences are often guided by rich background knowledge. Formal models of induction should aim to incorporate this knowledge and should explain how different kinds of knowledge lead to the distinctive patterns of reasoning found in different inductive contexts. This article presents a Bayesian framework that attempts to meet…

SOS-like induction in Bacillus subtilis: induction of the RecA protein analog and a damage-inducible operon by DNA damage in Rec+ and DNA repair-deficient strains

International Nuclear Information System (INIS)

Lovett, C.M. Jr.; Love, P.E.; Yasbin, R.E.; Roberts, J.W.

1988-01-01

We quantitated the induction of the Bacillus subtilis Rec protein (the analog of Escherichia coli RecA protein) and the B. subtilis din-22 operon (representative of a set of DNA damage-inducible operons in B. subtilis) following DNA damage in Rec+ and DNA repair-deficient strains. After exposure to mitomycin C or UV irradiation, each of four distinct rec (recA1, recB2, recE4, and recM13) mutations reduced to the same extent the rates of both Rec protein induction (determined by densitometric scanning of immunoblot transfers) and din-22 operon induction (determined by assaying beta-galactosidase activity in din-22::Tn917-lacZ fusion strains). The induction deficiencies in recA1 and recE4 strains were partially complemented by the E. coli RecA protein, which was expressed on a plasmid in B. subtilis; the E. coli RecA protein had no effect on either induction event in Rec+, recB2, or recM13 strains. These results suggest that (i) the expression of both the B. subtilis Rec protein and the din-22 operon share a common regulatory component, (ii) the recA1 and recE4 mutations affect the regulation and/or activity of the B. subtilis Rec protein, and (iii) an SOS regulatory system like the E. coli system is highly conserved in B. subtilis. We also showed that the basal level of B. subtilis Rec protein is about 4,500 molecules per cell and that maximum induction by DNA damage causes an approximately fivefold increase in the rate of Rec protein accumulation

Assessment and modeling of inductive and non-inductive scenarios for ITER

International Nuclear Information System (INIS)

Boucher, D.; Vayakis, G.; Moreau, D.

1999-01-01

This paper presents recent developments in modeling and simulations of ITER performances and scenarios. The first part presents an improved modeling of coupled divertor/main plasma operation including the simulation of the measurements involved in the control loop. The second part explores the fusion performances predicted under non-inductive operation with internal transport barrier. The final part covers a detailed scenario for non-inductive operation using a reverse shear configuration with lower hybrid and fast wave current drive. (author)

Single-Electrical-Port Control of Cascaded Doubly-Fed Induction Machine for EV/HEV Applications

DEFF Research Database (Denmark)

Han, Peng; Cheng, Ming; Chen, Zhe

2017-01-01

A single-electrical-port control scheme, for four-quadrant operation of cascaded doubly-fed induction machine (CDFIM), which has long been conceived as a motor or generator only suitable for limited two-quadrant operation, is proposed and theoretically demonstrated. The drive system is configured...... as slave inverter. With this configuration, the control emphasis is placed on the slave inverter, yielding reduced control complexity and cost, and the inaccuracy of flux estimation in conventional FOC for singly-fed induction machines is avoided at very low or even zero speed. It is found that the doubly...

[Mood induction procedures: a critical review].

Science.gov (United States)

Gilet, A-L

2008-06-01

For a long period in the history of psychological research, emotion and cognition have been studied independently, as if one were irrelevant to the other. The renewed interest of researchers for the study of the relations between cognition and emotion has led to the development of a range of laboratory methods for inducing temporary mood states. This paper aims to review the main mood induction procedures allowing the induction of a negative mood as well as a positive mood, developed since the pioneer study of Schachter and Singer [Psychol Rev 69 (1962) 379-399] and to account for the usefulness and problems related to the use of such techniques. The first part of this paper deals with the detailed presentation of some of the most popular mood induction procedures according to their type: simple (use of only one mood induction technique) or combined (association of two or more techniques at once). The earliest of the modern techniques is the Velten Mood Induction Procedure [Behav Res Ther 6 (1968) 473-482], which involves reading aloud sixty self-referent statements progressing from relative neutral mood to negative mood or dysphoria. Some researchers have varied the procedure slightly by changing the number of the statements [Behav Res Ther 21 (1983) 233-239, Br J Clin Psychol 21 (1982) 111-117, J Pers Soc Psychol 35 (1977) 625-636]. Various other mood induction procedures have been developed including music induction [Cogn Emotion 11 (1997) 403-432, Br J Med Psychol 55 (1982) 127-138], film clip induction [J Pers Soc Psychol 20 (1971) 37-43, Cogn Emotion 7 (1993) 171-193, Rottenberg J, Ray RR, Gross JJ. Emotion elicitation using films. In: Coan JA, Allen JJB, editors. The handbook of emotion elicitation and assessment. New York: Oxford University Press, 2007], autobiographical recall [J Clin Psychol 36 (1980) 215-226, Jallais C. Effets des humeurs positives et négatives sur les structures de connaissances de type script. Thèse de doctorat non publi

Induction accelerator test module for HIF

International Nuclear Information System (INIS)

Faltens, A.

1991-04-01

An induction linac test module suitable for investigating the drive requirements and the longitudinal coupling impedance of a high-power ion induction linac has been constructed by the Heavy Ion Fusion (HIF) group at LBL. The induction linac heavy ion driver for inertial confinement fusion (ICF) as presently envisioned uses multiple parallel beams which are transported in separate focusing channels but accelerated together in the induction modules. The resulting induction modules consequently have large beam apertures-1--2 meters in diameter- and correspondingly large outside diameters. The module geometry is related to a low-frequency ''gap capacity'' and high-frequency structural resonances, which are affected by the magnetic core loading and the module pulser impedance. A description of the test module and preliminary results are presented. 3 figs

Dynamic Average-Value Modeling of Doubly-Fed Induction Generator Wind Energy Conversion Systems

Science.gov (United States)

Shahab, Azin

In a Doubly-fed Induction Generator (DFIG) wind energy conversion system, the rotor of a wound rotor induction generator is connected to the grid via a partial scale ac/ac power electronic converter which controls the rotor frequency and speed. In this research, detailed models of the DFIG wind energy conversion system with Sinusoidal Pulse-Width Modulation (SPWM) scheme and Optimal Pulse-Width Modulation (OPWM) scheme for the power electronic converter are developed in detail in PSCAD/EMTDC. As the computer simulation using the detailed models tends to be computationally extensive, time consuming and even sometimes not practical in terms of speed, two modified approaches (switching-function modeling and average-value modeling) are proposed to reduce the simulation execution time. The results demonstrate that the two proposed approaches reduce the simulation execution time while the simulation results remain close to those obtained using the detailed model simulation.

[In case of fetal macrosomia, the best strategy is the induction of labor at 38 weeks of gestation].

Science.gov (United States)

Rozenberg, P

2016-11-01

Macrosomic fetuses are at increased risk of obstetric complications, and notably shoulder dystocia, responsible for a severe neonatal morbidity. In case of fetal macrosomia, three options are: (i) the elective cesarean delivery, but this is recommended only when the estimated fetal weight is≥4500g for diabetic women and 5000g for non-diabetic women; (ii) the expectative management, but children with birth weight≥4500 had significantly increased risk of perinatal mortality, neonatal asphyxia, trauma, and cesarean delivery; (iii) the induction of labor which, reducing the possibility of fetal growth, reduce the risk of cesarean delivery for cephalopelvic disproportion and shoulder dystocia. As 2 former trials did not show maternal or neonatal benefit with induction of labor for fetal macrosomia, it was therefore not recommended. However, these 2 studies had small sample size (273 and 40 women) and a methodology limiting their ability to show a difference, justifying to achieve a large multicentre randomized controlled trial. This trial was performed by Boulvain et al. and the results published in 2015 in the Lancet. Inclusion criteria were: a singleton pregnancy in cephalic presentation and a suspected fetal macrosomia defined by an ultrasound estimated weight>95th percentile between 36 and 38 weeks. Women were randomly assigned to receive induction of labor within 3 days between 37 +0  and 38 +6  weeks of gestation, or expectant management. Expectant management continued until either spontaneous labour or diagnosis of a condition necessitating induction. The primary outcome was a composite of clinically significant shoulder dystocia, fracture of the clavicle, brachial plexus injury, intracranial haemorrhage, or death. Baseline characteristics were similar between groups. The mean birth weight (±SD) was 3831 (±324) g in the induction group 4118 (±392) g in the expectant group. Induction of labor significantly reduced the risk of shoulder dystocia or

Evaluation of Breaking Performance in Vibration-Assisted Electrostatic Surface Induction Actuator

DEFF Research Database (Denmark)

Nemoto, Takeru; Zsurzsan, Tiberiu-Gabriel; Yamamoto, Akio

2015-01-01

This paper evaluates breaking performance of an electrostatic surface induction actuator. The actuator is equipped with piezoelectric vibrator such that the friction between the slider and the stator electrodes can be dramatically reduced by squeeze-film effect. In such an actuator, the friction...... conditions. The result clearly shows the effect of friction change in breaking performance of the actuator....

Inductive Loops for Sensing Position as Signature Signals

International Nuclear Information System (INIS)

Larbani, Sofiane; Malik, Noreha Abdul; Nordin, Anis Norashikin; Khan, Sheroz; Shobaki, Mohammad

2013-01-01

In this paper, an inductive sensing technique made of a special shaped inductive loop is proposed. The inductive loop has an inner turn fitted within an outer turn, making a total inductance value 100μH. This loop is made to be shown with balanced response using three capacitance values of 0.068μF each when a sinusoidal voltage source of 5V peak-to-peak is applied. The variation of the relative permeability of the inductance of the inductive loop (AL) results in a variation of the overall inductance value (L+AL), that causes the output signal to change in term of shape and amplitude for variation of total inductance sweep over a given period of time. As a result of change in inductance value (lμH) there is a correspondence increase of 300mV. Theoretical derivations have showed in close agreement with the simulation plots obtained using Multisim software

Inductive Loops for Sensing Position as Signature Signals

Science.gov (United States)

Larbani, Sofiane; Malik, Noreha Abdul; Norashikin Nordin, Anis; Khan, Sheroz; Shobaki, Mohammad

2013-12-01

In this paper, an inductive sensing technique made of a special shaped inductive loop is proposed. The inductive loop has an inner turn fitted within an outer turn, making a total inductance value 100μH. This loop is made to be shown with balanced response using three capacitance values of 0.068μF each when a sinusoidal voltage source of 5V peak-to-peak is applied. The variation of the relative permeability of the inductance of the inductive loop (AL) results in a variation of the overall inductance value (L+AL), that causes the output signal to change in term of shape and amplitude for variation of total inductance sweep over a given period of time. As a result of change in inductance value (lμH) there is a correspondence increase of 300mV. Theoretical derivations have showed in close agreement with the simulation plots obtained using Multisim software.

Relationship between polychlorinated biphenyl 126 treatment and cytochrome P4501A activity in chickens, as measured by in vivo caffeine and ex vivo ethoxyresorufin metabolism

Energy Technology Data Exchange (ETDEWEB)

Feyk, L.A.; Giesy, J.P.; Lambert, G.H.

1999-09-01

Cytochrome P4501A (CYPIA) activity is often used as a biomarker of exposure of wildlife to polyhalogenated diaromatic hydrocarbons (PHDHs) and is usually measured ex vivo in liver tissue. A caffeine breath test with radiolabeled substrate ({sup 14}C-CBT) has been developed to measure in vivo avian CYPIA activity. Research goals were to develop stable isotope methods ({sup 13}C-CBT), determine dose-response relationships between caffeine N-demethylation (CNDM) and PHDH exposure, and assess the relative utility of the CBT and ex vivo ethoxyresorufin-O-deethylase (EROD) assay. The {sup 13}C-CBT methods were developed with 20 chickens (Gallus domesticus). Chickens received three intraperitoneal injections of 0, 1, 5, or 50 {micro}g 3,3{prime},4,4{prime},5-pentachlorobiphenyl (PCB 126)/kg body weight, and CNDM was quantified by measurement of {sup 13}CO{sub 2}/{sup 12}CO{sub 2} in expired breath. The {sup 13}C-CBT was not as sensitive or specific as the EROD assay as an indicator of PHDH exposure and effect in birds. Constitutive CNDM of great interindividual variability was observed, and the magnitude of induction was greater for EROD activity than for CNDM (approximately 1,000- and 2-fold, respectively). Variability associated with baseline {sup 13}CO{sub 2}/{sup 12}CO{sub 2} ratios in expired breath reduced the sensitivity of the {sup 13}C-CBT method.

Inductive Communication System Design Summary

Science.gov (United States)

1978-09-01

The report documents the experience obtained during the design and development of the Inductive Communications System used in the Morgantown People Mover. The Inductive Communications System is used to provide wayside-to-vehicle and vehicle-to-waysid...

Erodibilidade e tensão crítica de cisalhamento em solos de estradas não pavimentadas Erodibility and critical shear stress on unpaved road soils

Directory of Open Access Journals (Sweden)

João F. de Oliveira

2009-12-01

Full Text Available A falta de um sistema adequado para drenagem de águas pluviais em estradas não pavimentadas é um dos principais fatores que causam a sua degradação e, para que referidos sistemas possam ser adequadamente planejados e dimensionados é necessário o conhecimento de parâmetros de resistência dos solos. Com este trabalho se teve, por objetivo, determinar a erodibilidade e a tensão crítica de cisalhamento para diferentes solos de estradas não pavimentadas. Utilizou-se um simulador de escoamento superficial instalado diretamente nos canais das estradas, sob condição natural e se determinou a perda de solo para diferentes lâminas de escoamento. A erodibilidade e a tensão crítica de cisalhamento foram determinadas por meio do ajuste de curvas relacionando-se a perda de solo em função da tensão cisalhante provocada pelo escoamento. Os resultados alcançados mostraram variações nos valores de erodibilidade e de tensão crítica de cisalhamento das estradas avaliadas. Os valores de erodibilidade encontrados mostraram, quando comparados com valores observados na literatura, elevada suscetibilidade à erosão para as condições de estradas, sendo mais elevados nos solos de textura mais arenosa e siltosa. Os valores de tensão crítica se mostraram bastante próximos aos observados em outros trabalhos.The absence of an adequate drainage system in unpaved roads is one of the main factors for their degradation. For adequate planning knowledge of the resistance parameters of soil is necessary. This study had as its objective the determinatiom of the erodibility and critical shear stress of unpaved road soils. For this work, a runoff simulator was directly installed on road channels, under natural conditions. Different flow depths were applied and the soil loss was measured for each depth. The erodibility and the critical shear stress were determined through adjusted curves relating soil disaggregation and flow shear stress. The results

Modeling and analysis with induction generators

CERN Document Server

Simões, M Godoy

2014-01-01

ForewordPrefaceAcknowledgmentsAuthorsPrinciples of Alternative Sources of Energy and Electric GenerationScope of This ChapterLegal DefinitionsPrinciples of Electrical ConversionBasic Definitions of Electrical PowerCharacteristics of Primary SourcesCharacteristics of Remote Industrial, Commercial, and Residential Sites and Rural EnergySelection of the Electric GeneratorInterfacing Primary Source, Generator, and LoadExample of a Simple Integrated Generating and Energy-Storing SystemSolved ProblemsSuggested ProblemsReferencesSteady-State Model of Induction GeneratorsScope of This ChapterInterconnection and Disconnection of the Electric Distribution NetworkRobustness of Induction GeneratorsClassical Steady-State Representation of the Asynchronous MachineGenerated PowerInduced TorqueRepresentation of Induction Generator LossesMeasurement of Induction Generator ParametersBlocked Rotor Test (s = 1)No-Load Test (s = 0)Features of Induction Machines Working as Generators Interconnected to the Distribution NetworkHigh-...

Hypnosis for induction of labour.

Science.gov (United States)

Nishi, Daisuke; Shirakawa, Miyako N; Ota, Erika; Hanada, Nobutsugu; Mori, Rintaro

2014-08-14

Induction of labour using pharmacological and mechanical methods can increase complications. Complementary and alternative medicine methods including hypnosis may have the potential to provide a safe alternative option for the induction of labour. However, the effectiveness of hypnosis for inducing labour has not yet been fully evaluated. To assess the effect of hypnosis for induction of labour compared with no intervention or any other interventions. We searched the Cochrane Pregnancy and Childbirth Group's Trials Register (31 January 2014), handsearched relevant conference proceedings, contacted key personnel and organisations in the field for published and unpublished references. All published and unpublished randomised controlled trials (RCTs) and cluster-RCTs of acceptable quality comparing hypnosis with no intervention or any other interventions, in which the primary outcome is to assess whether labour was induced. Two review authors assessed the one trial report that was identified (but was subsequently excluded). No RCTs or cluster-RCTs were identified from the search strategy. There was no evidence available from RCTs to assess the effect of hypnosis for induction of labour. Evidence from RCTs is required to evaluate the effectiveness and safety of this intervention for labour induction. As hypnosis may delay standard care (in case standard care is withheld during hypnosis), its use in induction of labour should be considered on a case-by-case basis.Future RCTs are required to examine the effectiveness and safety of hypnotic relaxation for induction of labour among pregnant women who have anxiety above a certain level. The length and timing of the intervention, as well as the staff training required, should be taken into consideration. Moreover, the views and experiences of women and staff should also be included in future RCTs.

The design of the accelerating gaps for the linear induction accelerator RADLAC II

International Nuclear Information System (INIS)

Shope, S.L.; Mazarakis, M.G.; Miller, R.B.; Poukey, J.W.

1987-01-01

In high current (50 kA) linear induction accelerators, the accelerating gaps can excite large radial oscillations. A gap was designed that minimized the radial oscillations and reduced potential depressions. The envelope equation predicted radial oscillation amplitudes of 1 mm which agreed with experimental measurements

Study on the plasma generation characteristics of an induction-triggered coaxial pulsed plasma thruster

Science.gov (United States)

Weisheng, CUI; Wenzheng, LIU; Jia, TIAN; Xiuyang, CHEN

2018-02-01

At present, spark plugs are used to trigger discharge in pulsed plasma thrusters (PPT), which are known to be life-limiting components due to plasma corrosion and carbon deposition. A strong electric field could be formed in a cathode triple junction (CTJ) to achieve a trigger function under vacuum conditions. We propose an induction-triggered electrode structure on the basis of the CTJ trigger principle. The induction-triggered electrode structure could increase the electric field strength of the CTJ without changing the voltage between electrodes, contributing to a reduction in the electrode breakdown voltage. Additionally, it can maintain the plasma generation effect when the breakdown voltage is reduced in the discharge experiments. The induction-triggered electrode structure could ensure an effective trigger when the ablation distance of Teflon increases, and the magnetic field produced by the discharge current could further improve the plasma density and propagation velocity. The induction-triggered coaxial PPT we propose has a simplified trigger structure, and it is an effective attempt to optimize the micro-satellite thruster.

Modulation of ethoxyresorufin O-deethylase and glutathione S-transferase activities in Nile tilapia (Oreochromis niloticus) by polycyclic aromatic hydrocarbons containing two to four rings: implications in biomonitoring aquatic pollution.

Science.gov (United States)

Pathiratne, Asoka; Hemachandra, Chamini K

2010-08-01

Despite ubiquity of polycyclic aromatic hydrocarbons (PAHs) in the tropical environments, little information is available concerning responses of tropical fish to PAHs and associated toxicity. In the present study, effects of five PAHs containing two to four aromatic rings on hepatic CYP1A dependent ethoxyresorufin O-deethylase (EROD), glutathione S-transferase (GST) and serum sorbitol dehydrogenase (SDH) activities in Nile tilapia, a potential fish species for biomonitoring pollution in tropical waters, were evaluated. Results showed that EROD activities were induced by the PAHs containing four aromatic rings (pyrene and chrysene) in a dose dependent manner. However PAHs with two to three aromatic rings (naphthalene, phenanthrene and fluoranthene) caused no effect or inhibition of EROD activities depending on the dose and the duration. Fluoranthene was the most potent inhibitor. SDH results demonstrated that high doses of fluoranthene induced hepatic damage. GST activity was induced by the lowest dose of phenanthrene, fluoranthene and chrysene but high doses had no effect. The results indicate that induction of EROD enzyme in Nile tilapia is a useful biomarker of exposure to PAHs such as pyrene and chrysene. However EROD inhibiting PAHs such as fluoranthene in the natural environment may modulate the EROD inducing potential of other PAHs thereby influencing PAH exposure assessments.

Rotor Speed Estimation Method Used in Dynamic Control of the Induction Motor

Directory of Open Access Journals (Sweden)

CRĂCIUNAŞ Gabriela

2013-10-01

Full Text Available In this paper it is proposed an algorithm for rotor speed estimation calculated directly from the rotor flux. The flux required for speed computation is estimated using Gopinath reduced order robust adaptive observer. In order to determine the structure of the observer we started from the state equations of the induction motor using spatial vectors written in fixed coordinates towards stator and considering the rotor speed constant. Quality of speed and rotor fluxestimation was evaluated from the results obtained during different operation regimes. The proposed algorithm was then tested for its usability in the case of indirect field oriented control based on the rotor flux of the induction motor by the simulation inMATLAB/Simulink.

PERFORMANCE OPTIMIZATION OF LINEAR INDUCTION MOTOR BY EDDY CURRENT AND FLUX DENSITY DISTRIBUTION ANALYSIS

Directory of Open Access Journals (Sweden)

M. S. MANNA

2011-12-01

Full Text Available The development of electromagnetic devices as machines, transformers, heating devices confronts the engineers with several problems. For the design of an optimized geometry and the prediction of the operational behaviour an accurate knowledge of the dependencies of the field quantities inside the magnetic circuits is necessary. This paper provides the eddy current and core flux density distribution analysis in linear induction motor. Magnetic flux in the air gap of the Linear Induction Motor (LIM is reduced to various losses such as end effects, fringes, effect, skin effects etc. The finite element based software package COMSOL Multiphysics Inc. USA is used to get the reliable and accurate computational results for optimization the performance of Linear Induction Motor (LIM. The geometrical characteristics of LIM are varied to find the optimal point of thrust and minimum flux leakage during static and dynamic conditions.

Relationship between the induction frequency and LTE in inductively coupled plasmas

International Nuclear Information System (INIS)

Mostaghimi, J.; Boulos, M.I.

1990-01-01

In this paper, the effect of the induction frequency on the local thermodynamic equilibrium (LTE) conditions in an inductively coupled plasma is investigated. Using generators with frequencies ranging from 5 to 56 MHz, a previous study investigated demonstrated the importance of this effect. Their measurements of the excitation temperatures of the iron atomic lines showed a sharp decrease in this temperature as a result of the increase in frequency. Another conclusion was that, all other parameters constant, increase in frequency will help the promotion of non-LTE effects

Zero Emission Mobility Systems in Cities. Inductive Recharge System Planning in Urban Areas

Directory of Open Access Journals (Sweden)

Giulio Maternini

2014-05-01

Full Text Available In the last few years, “Sustainable” and “Smart” mobility became concepts of fundamental importance and led national government to adopt programmes and measures aimed at reducing the carbon emissions of private and commercial vehicles. The final goal is to pursue the EU objectives of reducing the greenhouse gases emission in transportation sector. The progressive electrification of the circulating vehicles represents a possible solution to the air pollution relating problems. A recent innovative research field, which could significantly contribute to the diffusion of the electric vehicles, consists of the inductive recharge systems for electric vehicles. This technology could also bring to considerably environmental and logistic advantages, especially in urban areas. Starting from the analysis of the main ongoing experimentations of these innovative systems in the world, the present paper proposes a possible application of the inductive recharge technology to the public transport vehicles, through the presentation of the case study of Brescia.

Power crowbar system coupled by a current transformer with very low leakage inductance

International Nuclear Information System (INIS)

Kitagawa, S.; Hirano, K.I.

1976-01-01

A reliable, efficient power crowbar system has been developed for fast pinch experiments. In order to reduce the effective impedance of series capacitor system, a current transformer with extremely low leakage inductance has been designed and used. Primary and secondary windings of the transformer are alternately arranged as closely as possible. As a result, the leakage inductance is reduced to 2 nH. It is demonstrated that a current of 390 kA, the rise time of which is 4.5 μsec, is sustained for 100 μsec. Much larger system is being built, which maintains a current of 1 MA over 1 msec. The life of crowbar gap switches is prolonged by the aid of a mechanically-driven metal-to-metal contact switch. Another crowbar switch system with a high coulomb rating is under consideration, in which a gap switch is used together with a saturable reactor and a current transformer

Arginase induction and activation during ischemia and reperfusion and functional consequences for the heart

Directory of Open Access Journals (Sweden)

Klaus-Dieter eSchlüter

2015-03-01

Full Text Available Induction and activation of arginase is among the fastest responses of the heart to ischemic events. Induction of arginase expression and enzyme activation under ischemic conditions shifts arginine consumption from nitric oxide formation (NO to the formation of ornithine and urea. In the heart such a switch in substrate utilisation reduces the impact of the NO/cGMP-pathway on cardiac function that requires intact electromechanical coupling but at the same time it induces ornithine-dependent pathways such as the polyamine metabolism. Both effects significantly reduce the recovery of heart function during reperfusion and thereby limits the success of reperfusion strategies. In this context, changes in arginine consumption trigger cardiac remodelling in an unfavourable way and increases the risk of arrhythmia, specifically in the initial post-ischemic period in which arginase activity is dominating. However, during the entire ischemic period arginase activation might be a meaningful adaptation that is specifically relevant for reperfusion following prolonged ischemic periods. Therefore, a precise understanding about the underlying mechanism that leads to arginase induction as well as of it’s mechanistic impact on post-ischemic hearts is required for optimizing reperfusion strategies. In this review we will summarize our current understanding of these processes and give an outlook about possible treatment options for the future.

Cloning and nitrate induction of nitrate reductase mRNA

OpenAIRE

Cheng, Chi-Lien; Dewdney, Julia; Kleinhofs, Andris; Goodman, Howard M.

1986-01-01

Nitrate is the major source of nitrogen taken from the soil by higher plants but requires reduction to ammonia prior to incorporation into amino acids. The first enzyme in the reducing pathway is a nitrate-inducible enzyme, nitrate reductase (EC 1.6.6.1). A specific polyclonal antiserum raised against purified barley nitrate reductase has been used to immunoprecipitate in vivo labeled protein and in vitro translation products, demonstrating that nitrate induction increases nitrate reductase p...

Quality Induction: The Effects of Comprehensive Induction on New Teacher Retention and Job Satisfaction

Science.gov (United States)

Hendricks-Harris, Mary Therese

2012-01-01

This investigation examined the effect of a comprehensive new teacher induction program on teacher retention and job satisfaction in one suburban school district. New teachers are retained at low rates, and districts are spending resources in an attempt to decrease this number. New teacher induction includes supports for new teachers in their…

Mutation induction for improving of tangerine in Iran

Energy Technology Data Exchange (ETDEWEB)

Majd, F.; Jahangirzadeh, E.; Vedadi, S.; Tafti, M. Naseri; Rastegari, J. [Nuclear Research Center for Agriculture and Medicine, Karaj (Iran, Islamic Republic of)

2009-05-15

Genetic variation is an essential component of crop breeding. Induced mutations are highly effective in enhancing natural variability of genetic resources, and have been instrumental in developing improved cultivars of crops including fruits crops. Recent advances in biotechnological techniques have shown a great potential as efficient methodologies for vegetative micropropagation, screening techniques and genetic characterization including mutation induction. On this basis, a local, well- adapted and widely-consumed Clementine cultivar was selected for introduction into a mutation induction programme in order to reduce the excessive seeds in the fruits. A physical mutagen (γ-ray) was applied at doses of 35, 40 and 45 Gy on selected seedling apical buds. Irradiated buds were grafted onto sour orange root stocks (M{sub 1}V{sub 1}) and chimeras disassociated by further vegetative propagation. Finally M{sub 1}V{sub 3} plants were transferred to the field and after the production of fruits, selection for the desired fruit types was undertaken. The results showed that the radiation treatment was able to produce mutant genotypes with seedless fruits, early and late ripening and cold tolerance. (author)

Artificial Inductance Concept to Compensate Nonlinear Inductance Effects in the Back EMF-Based Sensorless Control Method for PMSM

DEFF Research Database (Denmark)

Lu, Kaiyuan; Lei, Xiao; Blaabjerg, Frede

2013-01-01

The back EMF-based sensorless control method is very popular for permanent magnet synchronous machines (PMSMs) in the medium- to high-speed operation range due to its simple structure. In this speed range, the accuracy of the estimated position is mainly affected by the inductance, which varies...... at different loading conditions due to saturation effects. In this paper, a new concept of using a constant artificial inductance to replace the actual varying machine inductance for position estimation is introduced. This facilitates greatly the analysis of the influence of inductance variation...

Plasma internal inductance dynamics in a tokamak

International Nuclear Information System (INIS)

Romero, J.A.

2010-01-01

A lumped parameter model for tokamak plasma current and inductance time evolution as a function of plasma resistance, non-inductive current drive sources and boundary voltage or poloidal field coil current drive is presented. The model includes a novel formulation leading to exact equations for internal inductance and plasma current dynamics. Having in mind its application in a tokamak inductive control system, the model is expressed in state space form, the preferred choice for the design of control systems using modern control systems theory. The choice of system states allows many interesting physical quantities such as plasma current, inductance, magnetic energy, and resistive and inductive fluxes be made available as output equations. The model is derived from energy conservation theorem, and flux balance theorems, together with a first order approximation for flux diffusion dynamics. The validity of this approximation has been checked using experimental data from JET showing an excellent agreement.

In vitro toxicity of selected pesticides on RTG-2 and RTL-W1 fish cell lines

International Nuclear Information System (INIS)

Babin, M.M.; Tarazona, J.V.

2005-01-01

The rainbow trout fish cell lines RTG-2 and RTL-W1 were used to determine the cytotoxic effects of the pesticides bifenthrin, cypermethrin, cyhalothrin, λ-cyhalothrin, quinalphos and chlorpyrifos. Cytotoxicity was measured by EROD and β-Gal enzymatic activities, the neutral red (NR) uptake assay, and the FRAME KB protein (KBP) assay. The β-Gal activity was unaffected by the pesticide exposure. The EROD activity was induced by cyhalothrin and λ-cyhalothrin (RTG-2 and RTL-W1) and by bifenthrin (RTL-W1). Dose dependent inhibition responses were observed for EROD activity in cells exposed to quinalphos (RTL-W1) and chlorpyrifos (RTG-2 and RTL-W1). RTL-W1 offered a better response for EROD induction. The EC50 values on EROD endpoint were more sensitive than NR and KBP. The acute fish toxicity of chlorpyrifos and quinalphos depends highly on the species; the species sensitivity distributions cover several orders of magnitude and the values obtained for EROS were within the lowest part of the reported ranges. - In vitro cell cultures can provide sensitive indicators for pesticide effects on biota

In vitro toxicity of selected pesticides on RTG-2 and RTL-W1 fish cell lines

Energy Technology Data Exchange (ETDEWEB)

Babin, M.M. [Laboratory for Ecotoxicology, Department of the Environment, INIA, Crta. de La Coruna Km 7, 28040 Madrid (Spain)]. E-mail: babin@inia.es; Tarazona, J.V. [Laboratory for Ecotoxicology, Department of the Environment, INIA, Crta. de La Coruna Km 7, 28040 Madrid (Spain)

2005-05-01

The rainbow trout fish cell lines RTG-2 and RTL-W1 were used to determine the cytotoxic effects of the pesticides bifenthrin, cypermethrin, cyhalothrin, {lambda}-cyhalothrin, quinalphos and chlorpyrifos. Cytotoxicity was measured by EROD and {beta}-Gal enzymatic activities, the neutral red (NR) uptake assay, and the FRAME KB protein (KBP) assay. The {beta}-Gal activity was unaffected by the pesticide exposure. The EROD activity was induced by cyhalothrin and {lambda}-cyhalothrin (RTG-2 and RTL-W1) and by bifenthrin (RTL-W1). Dose dependent inhibition responses were observed for EROD activity in cells exposed to quinalphos (RTL-W1) and chlorpyrifos (RTG-2 and RTL-W1). RTL-W1 offered a better response for EROD induction. The EC50 values on EROD endpoint were more sensitive than NR and KBP. The acute fish toxicity of chlorpyrifos and quinalphos depends highly on the species; the species sensitivity distributions cover several orders of magnitude and the values obtained for EROS were within the lowest part of the reported ranges. - In vitro cell cultures can provide sensitive indicators for pesticide effects on biota.

Snubber-less NPC inverter by a novel reduction technique of parasitic inductance for magnet power supplies

Energy Technology Data Exchange (ETDEWEB)

Koseki, K., E-mail: kunio.koseki@kek.jp; Morita, Y.

2014-10-11

The effects induced by parasitic inductance were studied in a neutral point clamped (NPC) inverter. The energy stored in the parasitic inductance by the output current causes a surge voltage during the turn-off period of semiconductor switches. The effect is serious in a magnet power supply for which a large excitation current is required. It is predicted by a circuit analysis that the parasitic inductance causes an electrical breakdown of the semiconductor switches. It was found that the most promising way to mitigate the effect is to reduce the parasitic inductance. With newly developed circuitry and layout of an NPC inverter, cancelation of the induced magnetic field, which is based on Ampere's circuital law, in power devices has been accomplished. The newly developed NPC inverter has been operated successfully with both a resistive dummy load and the dipole magnets in the main ring synchrotron at the J-PARC facility.

Probabilistic inductive inference: a survey

OpenAIRE

Ambainis, Andris

2001-01-01

Inductive inference is a recursion-theoretic theory of learning, first developed by E. M. Gold (1967). This paper surveys developments in probabilistic inductive inference. We mainly focus on finite inference of recursive functions, since this simple paradigm has produced the most interesting (and most complex) results.

Semipermeable membrane devices concentrate mixed function oxygenase inducers from oil sands and refinery wastewaters

International Nuclear Information System (INIS)

Parrott, J.L.; Hewitt, L.M.

2002-01-01

The health of fish in the Athabasca River was examined to determine the effects of both natural and anthropogenic oil sands exposure on liver mixed function oxygenase (MFO) enzymes. Semipermeable membrane devices (SPMD) were used to concentrate bioavailable compounds that may result in MFO induction. The SPMDs were used for a period of 2 weeks in the Steepbank River as well as in oil refinery wastewater and intake ponds. They were then tested to see if they induced ethoxyresorufin-O-deethylase (EROD) activity in hepatoma cells, a cell line derived from a liver cancer of a small fish. SPMDs from the wastewater pond contained potent EROD inducers in fish liver cells. SPMDs from the Athabasca River exhibited some EROD inducers, but they were 1/100 as potent as those of the refinery wastewater. The characteristics of MFO inducers from refinery wastewater were different from natural inducers from the oil sands in the Athabasca and Steepbank Rivers. For instance, log Kow was less than 5 for refinery wastewater, but it was greater than 5 for Athabasca River wastewater and from natural oil sands exposure. In the case of the Steepbank River, the pattern of MFO induction was similar to the MFO induction seen in wild fish.The highest MFO inducers were found to be in the area of the mine, suggesting and anthropogenic pollution source. The less potent inducers were in the area of the natural and undisturbed oil sands. Very few inducers were found outside of the oil sands formation

Differences in sensitivity of murine spermatogonia and somatic cells in vivo to sister-chromatid exchange induction by nitrosoureas.

Science.gov (United States)

Morales-Ramírez, P; Cruz-Vallejo, V; Rodríguez-Reyes, R

2001-07-01

Previously published data indicate that spermatogonia (SPG) are less sensitive to a sister-chromatid exchange (SCE) induction for different mutagens. In an earlier study, we have observed that bromodeoxyuridine (BrdU) substituted murine SPG are less sensitive to SCE induction by gamma ray in cells, than bone marrow (BM) and salivary gland (SG) cells in vivo. This was interpreted to mean that SPG are more efficient in DNA repair or are less prone to SCE induction. That the lower induction of SCE could be due to a reduced accessibility of mutagens to the SPG by virtue of a physiological barrier, was discarded by using gamma radiation. The aim of the present study was to establish whether or not there are differences in SCE induction by nitrosoureas among SPG, SG and BM cells with BrdU substituted or unsubstituted DNA. It was observed that SCE induction by methylnitrosourea (MNU) or by ethylnitrosourea (ENU) in SPG was, respectively, five and two times lower than in SG, and ten and three times lower than in BM. In SPG after BrdU incorporation, there was no increase in efficiency of SCE induction; in fact, there was even a slight decrease by exposure to MNU or ENU. BM and SG cells showed an increased efficiency in SCE induction after BrdU incorporation. This implies that SPG are also less sensitive to SCE induction by nitrosoureas, which cause a different kind of damage from previously assayed mutagens.

The Study of Residual Voltage of Induction Motor and the Influence of Various Parameters on the Residual Voltage

Science.gov (United States)

Zhang, Shuping; Zhao, Chen; Tan, Weipu

2017-05-01

The majority important load of industrial area is mainly composed of induction motor, it is more common that induction motor becomes sluggishness and even tripping due to the lose of power supply or other malfunction in the practical work. In this paper, space vector method is used to establish a reduced order model of induction motor, and then study the changes of motor electromagnetic after losing electricity. Based on motion equations of the rotor and magnetic flux conservation principle, it uses mathematical methods to deduce the expression of rotor current, rotor flux, the stator flux and the residual voltage of stator side. In addition, relying on thermal power plants, it uses the actual data of power plants, takes DIgsilent software to simulate the residual voltage of motor after losing electricity. analyses the influence on the residual voltage with the changes of the moment of inertia, load ratio, initial size of slip and the load characteristic of induction motor. By analysis of these, it has a more detailed understanding about the changes of residual voltage in practical application, in additional, it is more beneficial to put into standby power supply safely and effectively, moreover, reduce the influence of the input process to the whole system.

Workplace bullying erodes job and personal resources: between- and within-person perspectives.

Science.gov (United States)

Tuckey, Michelle R; Neall, Annabelle M

2014-10-01

Workplace bullying is a serious psychosocial occupational hazard. Despite a wealth of empirical study, research has rarely examined the mechanisms through which bullying has its negative effects. Accordingly, using both between- and within-person approaches, we investigated the erosion of job (Study 1) and personal (Study 2) resources following workplace bullying, mediated by the depletion of emotional energy. In Study 1, self-report survey data were collected from 221 retail workers at 2 time-points spaced 6 months apart. Structural equation modeling revealed that over time bullying depletes coworker support, partially mediated by emotional exhaustion. In Study 2, a 6-week diary was completed by a separate sample of 45 workers employed in various occupations. Within-person weekly variability in bullying exposure was 34%. Hierarchical linear modeling showed that weekly emotional exhaustion partially mediated the negative effects of weekly workplace bullying on both optimism and self-efficacy. The consistent pattern across both studies supports the idea of a resource loss process whereby exposure to bullying at work erodes job and personal resources by depleting energy. Future research should clarify the role of exhaustion in utilizing resources to respond to bullying, focus on predictors of within-person variability in bullying exposure, and more explicitly model the resource loss spiral following workplace bullying. (PsycINFO Database Record (c) 2014 APA, all rights reserved).

Sampling Assumptions in Inductive Generalization

Science.gov (United States)

Navarro, Daniel J.; Dry, Matthew J.; Lee, Michael D.

2012-01-01

Inductive generalization, where people go beyond the data provided, is a basic cognitive capability, and it underpins theoretical accounts of learning, categorization, and decision making. To complete the inductive leap needed for generalization, people must make a key "sampling" assumption about how the available data were generated.…

From Inductive Reasoning to Proof

Science.gov (United States)

Yopp, David A.

2009-01-01

Mathematical proof is an expression of deductive reasoning (drawing conclusions from previous assertions). However, it is often inductive reasoning (conclusions drawn on the basis of examples) that helps learners form their deductive arguments, or proof. In addition, not all inductive arguments generate more formal arguments. This article draws a…

Covariation in Natural Causal Induction.

Science.gov (United States)

Cheng, Patricia W.; Novick, Laura R.

1991-01-01

Biases and models usually offered by cognitive and social psychology and by philosophy to explain causal induction are evaluated with respect to focal sets (contextually determined sets of events over which covariation is computed). A probabilistic contrast model is proposed as underlying covariation computation in natural causal induction. (SLD)

Induction of the Wnt antagonist Dickkopf-1 is involved in stress-induced hippocampal damage.

Directory of Open Access Journals (Sweden)

Francesco Matrisciano

Full Text Available The identification of mechanisms that mediate stress-induced hippocampal damage may shed new light into the pathophysiology of depressive disorders and provide new targets for therapeutic intervention. We focused on the secreted glycoprotein Dickkopf-1 (Dkk-1, an inhibitor of the canonical Wnt pathway, involved in neurodegeneration. Mice exposed to mild restraint stress showed increased hippocampal levels of Dkk-1 and reduced expression of β-catenin, an intracellular protein positively regulated by the canonical Wnt signalling pathway. In adrenalectomized mice, Dkk-1 was induced by corticosterone injection, but not by exposure to stress. Corticosterone also induced Dkk-1 in mouse organotypic hippocampal cultures and primary cultures of hippocampal neurons and, at least in the latter model, the action of corticosterone was reversed by the type-2 glucocorticoid receptor antagonist mifepristone. To examine whether induction of Dkk-1 was causally related to stress-induced hippocampal damage, we used doubleridge mice, which are characterized by a defective induction of Dkk-1. As compared to control mice, doubleridge mice showed a paradoxical increase in basal hippocampal Dkk-1 levels, but no Dkk-1 induction in response to stress. In contrast, stress reduced Dkk-1 levels in doubleridge mice. In control mice, chronic stress induced a reduction in hippocampal volume associated with neuronal loss and dendritic atrophy in the CA1 region, and a reduced neurogenesis in the dentate gyrus. Doubleridge mice were resistant to the detrimental effect of chronic stress and, instead, responded to stress with increases in dendritic arborisation and neurogenesis. Thus, the outcome of chronic stress was tightly related to changes in Dkk-1 expression in the hippocampus. These data indicate that induction of Dkk-1 is causally related to stress-induced hippocampal damage and provide the first evidence that Dkk-1 expression is regulated by corticosteroids in the central

Effects of in vivo chronic exposure to pendimethalin on EROD activity and antioxidant defenses in rainbow trout (Oncorhynchus mykiss).

Science.gov (United States)

Danion, Morgane; Le Floch, Stéphane; Lamour, François; Quentel, Claire

2014-01-01

Pendimethalin, an herbicide active substance frequently used in terrestrial systems, has detected in European aquatic ecosystems. Reliable indicators still need to be found in order to properly assess the impact of pesticides in fish. After an in vivo chronic exposure to pendimethalin, the detoxification process and the antioxidant defense system were assessed in 120 adult rainbow trout, Oncorhynchus mykiss. Four nominal exposure conditions were tested: control (C), 500 ng L(-1) (P500), 800 ng L(-1) (P800) and the commercial formulation Prowl(®) at 500 ng L(-1) (Pw500). Fish samples were made after a 28 day exposure period (D28) and after a fifteen day recovery period in clean fresh water (D43). At D28, ethoxyresorufin-O-deethylase (EROD) activity was not activated in liver in spite of the pendimethalin uptake in fish. At D43, EROD activity in fish exposed to the commercial product was lower than in control fish, which may be explained by the high presence of herbicide in fish (613±163 ng g bile(-1)). Furthermore, antioxidant defense responses were set up by trout in gills and liver following chronic exposure to 800 ng L(-1) of pendimethalin concentration. While the glutathione content (GSH) decreased in gills, it increased in liver associated with higher activities of glutathione peroxidase (GPx) and superoxide dismutase (SOD). These disturbances could lead to reactive oxygen species production and oxidative stress in the vital organs in fish. After fifteen days in clean water, while the SOD activity was restored, the GSH content and GPx activity were still significantly disturbed in fish exposed to pendimethalin in comparison with control. These significant differences between treatments in antioxidant defenses parameters measured, attesting to the irreversibility of the effects. © 2013 Published by Elsevier Inc.

Buccal or sublingual misoprostol for cervical ripening and induction of labour.

Science.gov (United States)

Muzonzini, G; Hofmeyr, G J

2004-10-18

This is one of a series of reviews of cervical ripening and labour induction using standardised methodology. Misoprostol administered by the oral and sublingual routes have the advantage of rapid onset of action, while the sublingual and vaginal routes have the advantage of prolonged activity and greatest bioavailability. To determine the effectiveness and safety of misoprostol administered buccally or sublingually for third trimester cervical ripening and induction of labour. We searched the Cochrane Pregnancy and Childbirth Group trials register (8 December 2003), the Cochrane Central Register of Controlled Trials (The Cochrane Library, Issue 4, 2003), and bibliographies of relevant papers. Randomised controlled trials comparing buccal or sublingual misoprostol used for third trimester cervical ripening or labour induction with placebo/no treatment or other methods listed above it on a predefined list of labour induction methods. A generic strategy was developed to deal with the large volume and complexity of trial data relating to labour induction. Data were extracted onto standardized forms, checked for accuracy, and analysed using RevMan software. Three studies (502 participants) compared buccal/sublingual misoprostol respectively with a vaginal regimen (200 microg versus 50 microg) and with oral administration (50 versus 50 microg and 50 versus 100microg).The buccal route was associated with a trend to fewer caesarean sections than with the vaginal route (18/73 versus 28/79; relative risk (RR) 0.70; 95% confidence interval (CI) 0.42 to 1.15). There were no significant differences in any other outcomes. When the same dosage was used sublingually versus orally, the sublingual route was associated with less failures to achieve vaginal delivery within 24 hours (12/50 versus 19/50; RR 0.63, 95% CI 0.34 to 1.16), reduced oxytocin augmentation (17/50 versus 23/50; RR 0.74, 95% CI 0.45 to 1.21) and reduced caesarean section (8/50 versus 15/50; RR 0.53, 95% CI 0.25 to

Aplicación del bioensayo EROD-H4IIE para la determinación de dioxinas en carnes de pollos broiler: un estudio de equivalencia con la cromatografía de gases de alta resolución acoplada a espectrometría de masas de alta resolución Application of the EROD-H4IIE bioassay for the determination of dioxins in broiler chicken meat: an equivalence study with high resolution gas chromatography coupled to high resolution mass spectrometry

OpenAIRE

JT Schoffer; C Bustos-López; P Sotomayor; CA Mattar; A González; C Robles; F Samsing; O Acevedo; CE Valdovinos

2011-01-01

En el presente estudio se aplicó el bioensayo EROD con línea celular H4IIE para determinar la equivalencia de resultados para carnes de pollo, entre el bioensayo EROD-H4IIE en pg TCDD-EQ/g de tejido y los resultados de la cromatografía de gases de alta resolución acoplada a espectrometría de alta resolución (HRGC/HRMS) en pg WHO-TEQ/g de grasa. Para lo anterior se utilizaron 41 muestras compuestas de trutros de pollo. Éstas fueron obtenidas en la planta faenadora de 4 planteles diferentes de ...

Theoretical and experimental analysis of the induction generators; Analise teorica e experimental do gerador de inducao

Energy Technology Data Exchange (ETDEWEB)

Wu, Marcel; Martins Neto, Luciano; Calixto, Wesley Pacheco; Gontijo, Andre Luiz; Alves, Aylton Jose [Universidade Federal de Uberlandia (LMEE/FEELT/UFU), MG (Brazil). Fac. de Engenharia Eletrica. Lab. de Maquinas Eletricas Especiais], E-mails: marcel@mestrado.ufu.br, lmn@ufu.br, wpcalixto@ieee.org, aja@cefetgo.br

2009-10-15

Due to its lower costs, robustness, reduced maintenance and easy operation, the induction generator shows to be an economic alternative in small power generator systems. This work presents the initial phase of pertinent studies about the employment of the induction generator directly connected to the electrical power grid in a pilot project to be implemented at the Santa Luzia SHP. A project that aims to raise relevant operational aspects and to evidence some advantages about the employment of the induction generator in small power generator systems. This phase comprises the experimentation of an induction generator directly connected to the power grid in a laboratorial scale, plus a computational modeling which represents the same. This computational modeling takes into account loads variations which are being supplied by the generator, unbalance between phases and magnetic saturation effects, such as harmonic distortions in the generated currents. From the experimental model collected data, a theoretical-experimental confrontation of the computational modeling is made, where quantitative and qualitative analyses about the operational characteristics of the machine are made. The results of this work will head the operation and supervision of the SHP induction machine. (author)

Overview of Bearingless Induction Motors

Directory of Open Access Journals (Sweden)

Xiaodong Sun

2014-01-01

Full Text Available Bearingless induction motors combining functions of both torque generation and noncontact magnetic suspension together have attracted more and more attention in the past decades due to their definite advantages of compactness, simple structure, less maintenance, no wear particles, high rotational speed, and so forth. This paper overviews the key technologies of the bearingless induction motors, with emphasis on motor topologies, mathematical models, and control strategies. Particularly, in the control issues, the vector control, independent control, direct torque control, nonlinear decoupling control, sensorless control, and so forth are investigated. In addition, several possible development trends of the bearingless induction motors are also discussed.

Rapid COJEC Induction Therapy for High-risk Neuroblastoma Patients - Cochrane Review.

Science.gov (United States)

Peinemann, F; van Dalen, E C; Berthold, F

2016-04-01

Neuroblastoma is a rare malignant disease and patients with high-risk neuroblastoma have a poor prognosis. Rapid COJEC induction chemotherapy means (almost) the same total doses given within a shorter time period. In theory, rapid COJEC could reduce the risk of drug resistance and it has been considered as a potential candidate for improving the outcome. The objective was to evaluate effects of rapid COJEC compared to standard induction chemotherapy in patients with high-risk neuroblastoma. We searched the databases CENTRAL, MEDLINE, and EMBASE from inception to 11 November 2014 and included randomized controlled trials. We identified one relevant randomized controlled trial with 130 participants receiving rapid COJEC and 132 participants receiving standard OPEC/COJEC induction chemotherapy. There was no statistically significant difference between the treatment groups in complete response (risk ratio 0.99, 95% confidence interval 0.71 to 1.38, P=0.94) and treatment-related mortality (risk ratio 1.21, 95% confidence interval 0.33 to 4.39, P=0.77). A statistically significant difference in favor of the standard treatment arm was identified for the following early toxicities: febrile neutropenia, septicemia, and renal toxicity. The differences in complete response and treatment-related mortality between treatment alternatives were not statistically significantly different. Based on the currently available evidence, we are uncertain about the effects of rapid COJEC induction chemotherapy in patients with high-risk neuroblastoma. © Georg Thieme Verlag KG Stuttgart · New York.

Influences of lamin A levels on induction of pluripotent stem cells

Directory of Open Access Journals (Sweden)

Bingfeng Zuo

2012-09-01

Lamin A is an inner nuclear membrane protein that maintains nuclear structure integrity, is involved in transcription, DNA damage response and genomic stability, and also links to cell differentiation, senescence, premature aging and associated diseases. Induced pluripotent stem (iPS cells have been successfully generated from various types of cells and used to model human diseases. It remains unclear whether levels of lamin A influence reprogramming of somatic cells to pluripotent states during iPS induction. Consistently, lamin A is expressed more in differentiated than in relatively undifferentiated somatic cells, and increases in expression levels with age. Somatic cells with various expression levels of lamin A differ in their dynamics and efficiency during iPS cell induction. Cells with higher levels of lamin A show slower reprogramming and decreased efficiency to iPS cells. Furthermore, depletion of lamin A by transient shRNA accelerates iPS cell induction from fibroblasts. Reduced levels of lamin A are associated with increased expression of pluripotent genes Oct4 and Nanog, and telomerase genes Tert and Terc. On the contrary, overexpression of lamin A retards somatic cell reprogramming to iPS-like colony formation. Our data suggest that levels of lamin A influence reprogramming of somatic cells to pluripotent stem cells and that artificial silencing of lamin A facilitates iPS cell induction. These findings may have implications in enhancing rejuvenation of senescent or older cells by iPS technology and manipulating lamin A levels.

Induction Heating Process Design Using COMSOL Multiphysics Software

Directory of Open Access Journals (Sweden)

Andy Triwinarko

2011-08-01

Full Text Available Induction heating is clean environmental heating process due to a non-contact heating process. There is lots of the induction heating type that be used in the home appliance but it is still new technology in Indonesia. The main interesting area of the induction heating design is the efficiency of the usage of energy and choice of the plate material. COMSOL Multiphysics Software can be used to simulate and estimate the induction heating process. Therefore, the software can be used to design the induction heating process that will have a optimum efficiency. The properties of the induction heating design were also simulated and analyzed such as effect of inductors width, inductors distance, and conductive plate material. The result was shown that the good design of induction heating must have a short width and distance inductor and used silicon carbide as material plate with high frequency controller.

Automatic design of decision-tree induction algorithms

CERN Document Server

Barros, Rodrigo C; Freitas, Alex A

2015-01-01

Presents a detailed study of the major design components that constitute a top-down decision-tree induction algorithm, including aspects such as split criteria, stopping criteria, pruning, and the approaches for dealing with missing values. Whereas the strategy still employed nowadays is to use a 'generic' decision-tree induction algorithm regardless of the data, the authors argue on the benefits that a bias-fitting strategy could bring to decision-tree induction, in which the ultimate goal is the automatic generation of a decision-tree induction algorithm tailored to the application domain o

Smart Sensor for Online Detection of Multiple-Combined Faults in VSD-Fed Induction Motors

Science.gov (United States)

Garcia-Ramirez, Armando G.; Osornio-Rios, Roque A.; Granados-Lieberman, David; Garcia-Perez, Arturo; Romero-Troncoso, Rene J.

2012-01-01

Induction motors fed through variable speed drives (VSD) are widely used in different industrial processes. Nowadays, the industry demands the integration of smart sensors to improve the fault detection in order to reduce cost, maintenance and power consumption. Induction motors can develop one or more faults at the same time that can be produce severe damages. The combined fault identification in induction motors is a demanding task, but it has been rarely considered in spite of being a common situation, because it is difficult to identify two or more faults simultaneously. This work presents a smart sensor for online detection of simple and multiple-combined faults in induction motors fed through a VSD in a wide frequency range covering low frequencies from 3 Hz and high frequencies up to 60 Hz based on a primary sensor being a commercially available current clamp or a hall-effect sensor. The proposed smart sensor implements a methodology based on the fast Fourier transform (FFT), RMS calculation and artificial neural networks (ANN), which are processed online using digital hardware signal processing based on field programmable gate array (FPGA).

What Can a Hypnotic Induction Do?

Science.gov (United States)

Woody, Erik; Sadler, Pamela

2016-10-01

In contrast to how recent definitions of hypnosis describe the induction, a work-sample perspective is advocated that characterizes the induction as an initial, stage-setting phase encompassing everything in a hypnotic session up to the first hypnotic suggestion of particular relevance to the therapeutic or research goals at hand. Four major ways are then discussed in which the induction could affect subsequent hypnotic responses: It may provide information about how subsequent behaviors are to be enacted; it may provide cues about the nature of the interpersonal interaction to be expected in hypnosis; it may provide meta-suggestions, defined as suggestive statements intended to enhance responses to subsequent hypnotic suggestions; and it may provide a clear transition to help allow new behaviors and experiences to emerge. Several ideas for future research are advanced, such as mapping hypnosis style onto the interpersonal circumplex, evaluating whether attentional-state changes measured at the end of the induction actually mediate subsequent hypnotic responsiveness, and systematically examining the impact of ritual-like aspects of inductions.

A Student Teamwork Induction Protocol

Science.gov (United States)

Kamau, Caroline; Spong, Abigail

2015-01-01

Faulty group processes have harmful effects on performance but there is little research about intervention protocols to pre-empt them in higher education. This naturalistic experiment compared a control cohort with an inducted cohort. The inducted cohort attended a workshop, consultations, elected a leader and used tools (a group log and group…

Pulse induction heating

Energy Technology Data Exchange (ETDEWEB)

Vasiliev, A S; Kachanov, B Y; Kogan, B V

1993-12-31

Induction heating and three types of pulse processes were studied. It was found that in pulse processes the frequency and pulse duration of heat treatments do not remain constant. High frequency pulse heat treatments can be used on sprayed coatings; such treatments will result in stronger surfaces with no cracks. For induction hardening, the rate of specific power was 1 to 1.5 kW/sq.cm, for forging it was 0.2 to 0.3 kW/sq.cm and for melting it was 0.05 to 0.1 kW/sq.cm. The application of pulse heating will result in higher rates of specific power.

Inductive dielectric analyzer

International Nuclear Information System (INIS)

Agranovich, Daniel; Popov, Ivan; Ben Ishai, Paul; Feldman, Yuri; Polygalov, Eugene

2017-01-01

One of the approaches to bypass the problem of electrode polarization in dielectric measurements is the free electrode method. The advantage of this technique is that, the probing electric field in the material is not supplied by contact electrodes, but rather by electromagnetic induction. We have designed an inductive dielectric analyzer based on a sensor comprising two concentric toroidal coils. In this work, we present an analytic derivation of the relationship between the impedance measured by the sensor and the complex dielectric permittivity of the sample. The obtained relationship was successfully employed to measure the dielectric permittivity and conductivity of various alcohols and aqueous salt solutions. (paper)

Ribosomal trafficking is reduced in Schwann cells following induction of myelination

Directory of Open Access Journals (Sweden)

James M. Love

2015-08-01

Full Text Available Local synthesis of proteins within the Schwann cell periphery is extremely important for efficient process extension and myelination, when cells undergo dramatic changes in polarity and geometry. Still, it is unclear how ribosomal distributions are developed and maintained within Schwann cell projections to sustain local translation. In this multi-disciplinary study, we expressed a plasmid encoding a fluorescently labeled ribosomal subunit (L4-GFP in cultured primary rat Schwann cells. This enabled the generation of high-resolution, quantitative data on ribosomal distributions and trafficking dynamics within Schwann cells during early stages of myelination, induced by ascorbic acid treatment. Ribosomes were distributed throughout Schwann cell projections, with ~2-3 bright clusters along each projection. Clusters emerged within 1 day of culture and were maintained throughout early stages of myelination. Three days after induction of myelination, net ribosomal movement remained anterograde (directed away from the Schwann cell body, but ribosomal velocity decreased to about half the levels of the untreated group. Statistical and modeling analysis provided additional insight into key factors underlying ribosomal trafficking. Multiple regression analysis indicated that net transport at early time points was dependent on anterograde velocity, but shifted to dependence on anterograde duration at later time points. A simple, data-driven rate kinetics model suggested that the observed decrease in net ribosomal movement was primarily dictated by an increased conversion of anterograde particles to stationary particles, rather than changes in other directional parameters. These results reveal the strength of a combined experimental and theoretical approach in examining protein localization and transport, and provide evidence of an early establishment of ribosomal populations within Schwann cell projections with a reduction in trafficking following

Three-dimensional multi-terminal superconductive integrated circuit inductance extraction

International Nuclear Information System (INIS)

Fourie, Coenrad J; Wetzstein, Olaf; Kunert, Jürgen; Ortlepp, Thomas

2011-01-01

Accurate inductance calculations are critical for the design of both digital and analogue superconductive integrated circuits, and three-dimensional calculations are gaining importance with the advent of inductive biasing, inductive coupling and sky plane shielding for RSFQ cells. InductEx, an extraction programme based on the three-dimensional calculation software FastHenry, was proposed earlier. InductEx uses segmentation techniques designed to accurately model the geometries of superconductive integrated circuit structures. Inductance extraction for complex multi-terminal three-dimensional structures from current distributions calculated by FastHenry is discussed. Results for both a reflection plane modelling an infinite ground plane and a finite segmented ground plane that allows inductive elements to extend over holes in the ground plane are shown. Several SQUIDs were designed for and fabricated with IPHT's 1 kA cm −2 RSFQ1D niobium process. These SQUIDs implement a number of loop structures that span different layers, include vias, inductively coupled control lines and ground plane holes. We measured the loop inductance of these SQUIDs and show how the results are used to calibrate the layer parameters in InductEx and verify the extraction accuracy. We also show that, with proper modelling, FastHenry can be fast enough to be used for the extraction of typical RSFQ cell inductances.

Studies on dual fuel operation of rubber seed oil and its bio-diesel with hydrogen as the inducted fuel

Energy Technology Data Exchange (ETDEWEB)

Edwin Geo, V.; Nagalingam, B. [Department of Mechanical Engineering, KCG College of Technology, Chennai, Tamil Nadu 600097 (India); Nagarajan, G. [Department of Mechanical Engineering, IC Engineering Division, Anna University, Chennai, Tamil Nadu 600025 (India)

2008-11-15

The main problems with the use of neat vegetable oils in diesel engines are higher smoke levels and lower thermal efficiency as compared to diesel. The problem can be tackled by inducting a gaseous fuel in the intake manifold along with air. In this investigation, hydrogen is used as the inducted fuel and rubber seed oil (RSO), rubber seed oil methyl ester (RSOME) and diesel are used as main fuels in a dual fuel engine. A single cylinder diesel engine with rated output of 4.4 kW at 1500 rpm was converted to operate in the dual fuel mode. Dual fuel operation of varying hydrogen quantity with RSO and RSOME results in higher brake thermal efficiency and significant reduction in smoke levels at high outputs. The maximum brake thermal efficiency is 28.12%, 29.26% and 31.62% with RSO, RSOME and diesel at hydrogen energy share of 8.39%, 8.73% and 10.1%, respectively. Smoke is reduced from 5.5 to 3.5 BSU with RSOME and for RSO it is from 6.1 to 3.8 BSU at the maximum efficiency point. The peak pressure and maximum rate of pressure rise increase with hydrogen induction. Heat release rate indicates an increase in the combustion rate with hydrogen induction. On the whole it is concluded that hydrogen can be inducted along with air in order to reduce smoke levels and improve thermal efficiency of RSO and its bio-diesel fuelled diesel engines. (author)

Induction of Biomolecules in Mature Leaves of Terminalia arjuna Due to Feeding of Antheraea mylitta Drury

Directory of Open Access Journals (Sweden)

G. Abraham

2004-01-01

Full Text Available Terminalia arjuna is an important food plant of the tasar silkworm, Antheraea mylitta Drury. In this study, we investigated the induction of biomolecules in mature leaves of these plants subjected to insect feeding. Increase in total tannin content, lipid peroxidation, and trypsin inhibitor activity have been observed in mature leaves damaged by the insects. The growth rate of Vth instar larvae of A. mylitta fed on previously damaged foliage reduced by 87.1%. Induction of biomolecules for defense mechanisms in relation to herbivore damage has been discussed.

The Impact of Induction/Mentoring on Job Satisfaction and Retention of Novice Teachers

Science.gov (United States)

Williams, Ingrid Rene'e

2012-01-01

Teachers are essential to the success of all students. In an effort to reduce high teacher turnover, states and/or school systems are implementing induction/mentoring programs as a mechanism for supporting teachers in their early years. The issue is not the availability of teachers; higher education is producing more than enough qualified…

Linking Ah receptor mediated effects of sediments and impacts on fish to key pollutants in the Yangtze Three Gorges Reservoir, China - A comprehensive perspective.

Science.gov (United States)

Floehr, Tilman; Scholz-Starke, Björn; Xiao, Hongxia; Hercht, Hendrik; Wu, Lingling; Hou, Junli; Schmidt-Posthaus, Heike; Segner, Helmut; Kammann, Ulrike; Yuan, Xingzhong; Roß-Nickoll, Martina; Schäffer, Andreas; Hollert, Henner

2015-12-15

The Three Gorges Reservoir (TGR), created in consequence of the Yangtze River's impoundment by the Three Gorges Dam, faces numerous anthropogenic impacts that challenge its unique ecosystem. Organic pollutants, particularly aryl hydrocarbon receptor (AhR) agonists, have been widely detected in the Yangtze River, but only little research was yet done on AhR-mediated activities. Hence, in order to assess effects of organic pollution, with particular focus on AhR-mediated activities, several sites in the TGR area were examined applying the "triad approach". It combines chemical analysis, in vitro, in vivo and in situ investigations to a holistic assessment. Sediments and the benthic fish species Pelteobagrus vachellii were sampled in 2011/2012, respectively, to identify relevant endpoints. Sediment was tested in vitro with the ethoxyresorufin-O-deethylase (EROD) induction assay, and in vivo with the Fish Embryo Toxicity Test and Sediment Contact Assay with Danio rerio. Activities of phase I (EROD) and phase II (glutathione-S-transferase) biotransformation enzymes, pollutant metabolites and histopathological alterations were studied in situ in P. vachellii. EROD induction was tested in vitro and in situ to evaluate possible relationships. Two sites, near Chongqing and Kaixian city, were identified as regional hot-spots and further investigated in 2013. The sediments induced in the in vitro/in vivo bioassays AhR-mediated activities and embryotoxic/teratogenic effects - particularly on the cardiovascular system. These endpoints could be significantly correlated to each other and respective chemical data. However, particle-bound pollutants showed only low bioavailability. The in situ investigations suggested a rather poor condition of P. vachellii, with histopathological alterations in liver and excretory kidney. Fish from Chongqing city exhibited significant hepatic EROD induction and obvious parasitic infestations. The polycyclic aromatic hydrocarbon (PAH) metabolite 1

Scalable conditional induction variables (CIV) analysis

KAUST Repository

Oancea, Cosmin E.; Rauchwerger, Lawrence

2015-01-01

challenges to automatic parallelization. Because the complexity of such induction variables is often due to their conditional evaluation across the iteration space of loops we name them Conditional Induction Variables (CIV). This paper presents a flow

Toxicity of polybrominated diphenyl ethers (de-71) in chicken (Gallus gallus), mallard (Anas platyrhynchos), and American kestrel (Falco sparverius) embryos and hatchlings

Science.gov (United States)

McKernan, M.A.; Rattner, B.A.; Hale, R.C.; Ottinger, M.A.

2009-01-01

Embryonic survival, pipping and hatching success, and sublethal biochemical, endocrine, and histological endpoints were examined in hatchling chickens (Gallus gallus), mallards (Anas platyrhynchos), and American kestrels (Falco sparverius) following air cell administration of a pentabrominated diphenyl ether (penta-BDE; DE-71) mixture (0.01-20 mu g/g egg) or polychlorinated biphenyl (PCB) congener 126 (3,3', 4,4', 5-pentachlorobiphenyl; 0.002 mu g/g egg). The penta-BDE decreased pipping and hatching success at concentrations of 10 and 20 mu g/g egg in kestrels but had no effect on survival endpoints in chickens or mallards. Sublethal effects in hatchling chickens included ethoxyresorufin-O-dealkylase (EROD) induction and histological changes in the bursa, but these responses were not observed in other species. Polychlorinated biphenyl congener 126 (positive control) reduced survival endpoints in chicken and kestrel embryos and caused sublethal effects (EROD induction, reduced bursal mass and follicle size) in chickens. Mallards were clearly less sensitive than the other species to administered penta-BDE and PCB 126. In a second experiment, the absorption of penta-BDE (11.1 mu g/g egg, air cell administered during early development) into the contents of chicken and kestrel eggs was determined at various intervals (24 h postinjection, midincubation, and pipping). By pipping, 29% of the penta-BDE administered dose was present in the egg contents in chickens, and 18% of the administered dose was present in kestrel egg contents. Based on uptake in kestrels, the lowest-observed-effect level on pipping and hatching success may be as low as 1.8 mu g total penta-BDE/g egg, which approaches concentrations detected in eggs of free-ranging birds. Because some penta-BDE congeners are still increasing in the environment, the toxic effects observed in the present study are cause for concern in wildlife.

Induction Brazing

DEFF Research Database (Denmark)

Henningsen, Poul

, or if the hottest area is located outside the joint interface, a number of defects may appear: the braze metal may flow away from the joint, the flux may burn off, poor binding of the braze metal may appear or the braze metal may be overheated. Joint geometry as well as electro-magnetic properties of the work piece...... presents a combined numerical and experimental method for determination of appropriate/optimiged coil geometry and position in induction brazing tube-to-plate joints of different ratios between tube and plate thickness and different combinations of the materials stainless steel, brass and copper....... The method has proven to give successful results in brazing tube-plate joints of copper-brass, copper-stainless steel, stainless steel-brass, and stainless steel-stainless steel. A new design of an adjustable flux concentrator for induction heating tube-to-plate joints is proposed and tested on a variety...

Addiction, adolescence, and innate immune gene induction

Directory of Open Access Journals (Sweden)

Fulton T Crews

2011-04-01

Full Text Available Repeated drug use/abuse amplifies psychopathology, progressively reducing frontal lobe behavioral control and cognitive flexibility while simultaneously increasing limbic temporal lobe negative emotionality. The period of adolescence is a neurodevelopmental stage characterized by poor behavioral control as well as strong limbic reward and thrill seeking. Repeated drug abuse and/or stress during this stage increase the risk of addiction and elevate activator innate immune signaling in the brain. Nuclear factor-kappa-light-chain-enhancer of activated B cells (NF-κB is a key glial transcription factor that regulates proinflammatory chemokines, cytokines, oxidases, proteases, and other innate immune genes. Induction of innate brain immune gene expression (e.g., NF-κB facilitates negative affect, depression-like behaviors, and inhibits hippocampal neurogenesis. In addition, innate immune gene induction alters cortical neurotransmission consistent with loss of behavioral control. Studies with anti-oxidant, anti-inflammatory, and anti-depressant drugs as well as opiate antagonists link persistent innate immune gene expression to key behavioral components of addiction, e.g. negative affect-anxiety and loss of frontal cortical behavioral control. This review suggests that persistent and progressive changes in innate immune gene expression contribute to the development of addiction. Innate immune genes may represent a novel new target for addiction therapy.

Experimental demonstration of the KEK induction synchrotron

International Nuclear Information System (INIS)

Takayama, Ken; Torikai, Kota; Shimosaki, Yoshito; Kono, Tadaaki; Iwashita, Taiki; Arakida, Yoshio; Nakamura, Eiji; Shirakata, Masashi; Sueno, Takeshi; Wake, Masayoshi; Otsuka, Kazunori

2007-01-01

Recent progress in the KEK induction synchrotron is presented. In the recent experiment, by using a newly developed induction acceleration system instead of radio-wave acceleration devices, a single proton bunch injected from the 500 MeV Booster ring and captured by the barrier bucket created by the induction step-voltages was accelerated to 6 GeV in the KEK proton synchrotron

[Evaluation of the scales used to measure anxiety and child behaviour during the induction of anaesthesia. Literature review].

Science.gov (United States)

Jerez, C; Lázaro, J J; Ullán, A M

2016-02-01

The assessment of children's anxiety during anaesthetic induction is useful to determine if pre-operative strategies have been effective in reducing anxiety. The aim of this study is to review the different tools used to evaluate child anxiety or behaviour during the induction of anaesthesia. The electronic databases with no date limits were reviewed in December 2013, with a second review repeated in September 2014. A data extraction template was applied to find the scales used in the articles. Eight observational scales were found. Six of them can only be used during induction of anaesthesia, and two of those could be applied at various perioperative times, before surgery and during induction of anaesthesia. Copyright © 2014 Sociedad Española de Anestesiología, Reanimación y Terapéutica del Dolor. Publicado por Elsevier España, S.L.U. All rights reserved.

Research on Stabilization Properties of Inductive-Capacitive Transducers Based on Hybrid Electromagnetic Elements

Science.gov (United States)

Konesev, S. G.; Khazieva, R. T.; Kirllov, R. V.; Konev, A. A.

2017-01-01

Some electrical consumers (the charge system of storage capacitor, powerful pulse generators, electrothermal systems, gas-discharge lamps, electric ovens, plasma torches) require constant power consumption, while their resistance changes in the limited range. Current stabilization systems (CSS) with inductive-capacitive transducers (ICT) provide constant power, when the load resistance changes over a wide range and increaseы the efficiency of high-power loads’ power supplies. ICT elements are selected according to the maximum load, which leads to exceeding a predetermined value of capacity. The paper suggests carrying load power by the ICT based on multifunction integrated electromagnetic components (MIEC) to reduce the predetermined capacity of ICT elements and CSS weights and dimensions. The authors developed and patented ICT based on MIEC that reduces the CSS weights and dimensions by reducing components number with the possibility of device’s electric energy transformation and resonance frequency changing. An ICT mathematical model was produced. The model determines the width of the load stabilization range. Electromagnetic processes study model was built with the MIEC integral parameters (full inductance of the electrical lead, total capacity, current of electrical lead). It shows independence of the load current from the load resistance for different ways of MIEC connection.

Interactive Effects of Jasmonic Acid, Salicylic Acid, and Gibberellin on Induction of Trichomes in Arabidopsis1

Science.gov (United States)

Traw, M. Brian; Bergelson, Joy

2003-01-01

Leaf trichomes protect plants from attack by insect herbivores and are often induced following damage. Hormonal regulation of this plant induction response has not been previously studied. In a series of experiments, we addressed the effects of artificial damage, jasmonic acid, salicylic acid, and gibberellin on induction of trichomes in Arabidopsis. Artificial damage and jasmonic acid caused significant increases in trichome production of leaves. The jar1-1 mutant exhibited normal trichome induction following treatment with jasmonic acid, suggesting that adenylation of jasmonic acid is not necessary. Salicylic acid had a negative effect on trichome production and consistently reduced the effect of jasmonic acid, suggesting negative cross-talk between the jasmonate and salicylate-dependent defense pathways. Interestingly, the effect of salicylic acid persisted in the nim1-1 mutant, suggesting that the Npr1/Nim1 gene is not downstream of salicylic acid in the negative regulation of trichome production. Last, we found that gibberellin and jasmonic acid had a synergistic effect on the induction of trichomes, suggesting important interactions between these two compounds. PMID:14551332

Propagation of ULF waves through the ionosphere: Inductive effect for oblique magnetic fields

Directory of Open Access Journals (Sweden)

M. D. Sciffer

2004-04-01

Full Text Available Solutions for ultra-low frequency (ULF wave fields in the frequency range 1–100mHz that interact with the Earth's ionosphere in the presence of oblique background magnetic fields are described. Analytic expressions for the electric and magnetic wave fields in the magnetosphere, ionosphere and atmosphere are derived within the context of an inductive ionosphere. The inductive shielding effect (ISE arises from the generation of an "inductive" rotational current by the induced part of the divergent electric field in the ionosphere which reduces the wave amplitude detected on the ground. The inductive response of the ionosphere is described by Faraday's law and the ISE depends on the horizontal scale size of the ULF disturbance, its frequency and the ionosphere conductivities. The ISE for ULF waves in a vertical background magnetic field is limited in application to high latitudes. In this paper we examine the ISE within the context of oblique background magnetic fields, extending studies of an inductive ionosphere and the associated shielding of ULF waves to lower latitudes. It is found that the dip angle of the background magnetic field has a significant effect on signals detected at the ground. For incident shear Alfvén mode waves and oblique background magnetic fields, the horizontal component of the field-aligned current contributes to the signal detected at the ground. At low latitudes, the ISE is larger at smaller conductivity values compared with high latitudes.

Key words. Ionosphere (ionosphere-magnetosphere interactions; electric fields and currents; wave propagation

Efficiency optimized control of medium-size induction motor drives

DEFF Research Database (Denmark)

Abrahamsen, F.; Blaabjerg, Frede; Pedersen, John Kim

2000-01-01

The efficiency of a variable speed induction motor drive can be optimized by adaption of the motor flux level to the load torque. In small drives (<10 kW) this can be done without considering the relatively small converter losses, but for medium-size drives (10-1000 kW) the losses can not be disr......The efficiency of a variable speed induction motor drive can be optimized by adaption of the motor flux level to the load torque. In small drives (... not be disregarded without further analysis. The importance of the converter losses on efficiency optimization in medium-size drives is analyzed in this paper. Based on the experiments with a 90 kW drive it is found that it is not critical if the converter losses are neglected in the control, except...... that the robustness towards load disturbances may unnecessarily be reduced. Both displacement power factor and model-based efficiency optimizing control methods perform well in medium-size drives. The last strategy is also tested on a 22 kW drive with good results....

Social perception of soil conservation benefits in Kondoa eroded area of Tanzania

Directory of Open Access Journals (Sweden)

Rajendra P. Shrestha

2015-09-01

Full Text Available A soil conservation project was implemented in Tanzania for over 30 years. This study applied a socio-economic approach to examine and analyse the benefits of soil conservation in the Kondoa eroded area of Tanzania by conducting a household survey of 240 households. The study findings show that 89% and 70% of respondents consider soil conservation activities have increased vegetation and soil fertility, respectively. Decreased soil erosion was perceived by 68% of respondents, increased firewood by 98%, increased fodder by 50%, high crop yields by 56%, and food sufficiency by 68%. These are the outcomes of conservation tillage, integrated farming and use of organic fertilizers, controlled stall feeding, agroforestry, construction of cut off drains, contour bunds and contour ridges cultivation, which are the main land use practices in the area. Access to extension services, household sizes, long term land ownership, crop incomes and awareness of soil conservation project were found to determine the level of participation in soil conservation. Major challenges are the lack of sustainability of those activities because of a recent policy decision to withdraw conservation investment. Despite the challenge, this study concluded that past government efforts on soil conservation activities initiated since the early 1970s through decentralization, institutional collaboration, socioeconomic support to farmers and continuous local community participation in restoring the degraded ecosystem of Kondoa have contributed to ensure environmental and socio-economic sustainability in the area.

Remineralization of eroded enamel by a NaF rinse containing a novel calcium phosphate agent in an in situ model: a pilot study

Directory of Open Access Journals (Sweden)

Bennett T Amaechi

2010-08-01

Full Text Available Bennett T Amaechi1, Ramalingam Karthikeyan1, Poornima K Mensinkai1, Kaveh Najibfard1, Allen C Mackey2, Robert L Karlinsey21University of Texas Health Science Center at San Antonio, San Antonio, Texas, USA; 2Indiana Nanotech, Indianapolis, IN, USAPurpose: An in situ study evaluated the remineralization potential of 225 ppm fluoride (F rinses with and without a calcium phosphate agent (TCP-Si-Ur on eroded enamel.Methods: 20 human patients participated in this IRB approved study. Enamel blocks extracted from 20 human molars were assigned to each of the three study phases (G1, G2, G3. Each block was eroded using 1% citric acid (pH = 2.5, with a slice cut from each block to establish baseline lesion parameters (ie, integrated mineral loss ∆Z, and lesion depth LD using ­transverse microradiography (TMR. Participants and assigned blocks were randomly divided into three 28-day phases. The blocks were mounted into modified orthodontic brackets and bonded to the buccal surface of one of the subject’s mandibular molars. The appliance remained in the ­subject’s mouth for 28 days. Prior to each study phase, participants observed a one-week-washout period using a fluoride-free dentifrice. In each phase, participants brushed with the fluoride-free ­dentifrice for 1 min, followed by one of the following coded treatments: G1: 225 ppm F + 40 ppm ­TCP-Si-Ur rinse (1 min; G2: 225 ppm F rinse (1 min; G3: no rinse (saliva-only. After each phase, appliances were removed and specimens were analyzed using TMR.Results: TMR data (ie, ∆Z and LD revealed all three groups significantly remineralized eroded enamel (paired t-tests, P , 0.001. Net mineralization (% change in ∆Z, LD were as follows (mean (std.dev.: G1: 44.1 (22.6, 30.5 (27.0; G2: 30.0 (7.4, 29.4 (10.5; G3: 23.8 (16.4, 25.7 (15.5. Furthermore, G1 was found to cause significantly more remineralization than G2 (P = 0.039 and G3, (P = 0.002.Conclusion: Mouthrinse containing 225 ppm F plus TCP

Inter-Kingdom Modification of Metabolic Behavior: [GAR+] Prion Induction in Saccharomyces cerevisiae Mediated by Wine Ecosystem Bacteria

Directory of Open Access Journals (Sweden)

Linda F Bisson

2016-11-01

Full Text Available The yeast Saccharomyces cerevisiae has evolved to dominate grape juice fermentation. A suite of cellular properties, rapid nutrient depletion, production of inhibitory compounds and the metabolic narrowing of the niche, all enable a minor resident of the initial population to dramatically increase its relative biomass in the ecosystem. This dominance of the grape juice environment is fueled by a rapid launch of glycolysis and energy generation mediated by transport of hexoses and an efficient coupling of transport and catabolism. Fermentation occurs in the presence of molecular oxygen as the choice between respiratory or fermentative growth is regulated by the availability of sugar a phenomenon known as glucose or catabolite repression. Induction of the GAR+ prion alters the expression of the major hexose transporter active under these conditions, Hxt3, reducing glycolytic capacity. Bacteria present in the grape juice ecosystem were able to induce the GAR+ prion in wine strains of S. cerevisiae. This induction reduced fermentation capacity but did not block it entirely. However, dominance factors such as the rapid depletion of amino acids and other nitrogen sources from the environment were impeded enabling greater access to these substrates for the bacteria. Bacteria associated with arrested commercial wine fermentations were able to induce the prion state, and yeast cells isolated from arrested commercial fermentations were found to be GAR+ thus confirming the ecological relevance of prion induction. Subsequent analyses demonstrated that the presence of environmental acetic acid could lead to GAR+ induction in yeast strains under certain conditions. The induction of the prion enabled yeast growth on non-preferred substrates, oxidation and reduction products of glucose and fructose, present as a consequence of bacterial energy production. In native ecosystems prion induction never exceeded roughly 50-60% of the population of yeast cells

Induction practice -

DEFF Research Database (Denmark)

Rohde, Nicolas; Sprogøe, Jonas

2007-01-01

that induction potentially triggers both individual and organizational learning and by drawing on practice-based theory we discuss how the interplay between individual and the organization, what we call agenerative dance, ignites both kinds of learning. We focus on and describe the interplay , ignites both kinds...

Calculation of Leakage Inductance for High Frequency Transformers

DEFF Research Database (Denmark)

Ouyang, Ziwei; Jun, Zhang; Hurley, William Gerard

2015-01-01

Frequency dependent leakage inductance is often observed. High frequency eddy current effects cause a reduction in leakage inductance. The proximity effect between adjacent layers is responsible for the reduction of leakage inductance. This paper gives a detailed analysis of high frequency leakag...

Surface remineralization potential of casein phosphopeptide-amorphous calcium phosphate on enamel eroded by cola-drinks: An in-situ model study

Directory of Open Access Journals (Sweden)

Navneet Grewal

2013-01-01

Full Text Available Aim: The aim of this study was to investigate the remineralization potential of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP on enamel eroded by cola drinks. Subjects and Methods: A total of 30 healthy subjects were selected from a random sample of 1200 children and divided into two groups of 15 each wherein calcium and phosphorus analyses and scanning electron microscope (SEM analysis was carried out to investigate the remineralization of enamel surface. A total of 30 non-carious premolar teeth were selected from the human tooth bank (HTB to prepare the in-situ appliance. Three enamel slabs were prepared from the same. One enamel slab was used to obtain baseline values and the other two were embedded into the upper palatal appliances prepared on the subjects′ maxillary working model. The subjects wore the appliance after which 30 ml cola drink exposure was given. After 15 days, the slabs were removed and subjected to respective analysis. Statistical Analysis Used: Means of all the readings of soluble calcium and phosphorous levels at baseline,post cola-drink exposure and post cpp-acp application were subjected to statistical analysis SPSS11.5 version.Comparison within groups and between groups was carried out using ANOVA and F-values at 1% level of significance. Results: Decrease in calcium solubility of enamel in the CPP-ACP application group as compared to post-cola drink exposure group (P < 0.05 was seen. Distinctive change in surface topography of enamel in the post-CPP-ACP application group as compared to post-cola drink exposure group was observed. Conclusion: CPP-ACP significantly promoted remineralization of enamel eroded by cola drinks as revealed by significant morphological changes seen in SEM magnification and spectrophotometric analyses.

Rule Induction-Based Knowledge Discovery for Energy Efficiency

OpenAIRE

Chen, Qipeng; Fan, Zhong; Kaleshi, Dritan; Armour, Simon M D

2015-01-01

Rule induction is a practical approach to knowledge discovery. Provided that a problem is developed, rule induction is able to return the knowledge that addresses the goal of this problem as if-then rules. The primary goals of knowledge discovery are for prediction and description. The rule format knowledge representation is easily understandable so as to enable users to make decisions. This paper presents the potential of rule induction for energy efficiency. In particular, three rule induct...

Proton induction linacs as high-intensity neutron sources

International Nuclear Information System (INIS)

Keefe, D.; Hoyer, E.

1981-01-01

Proton induction linacs are explored as high intensity neutron sources. The induction linac - concept, properties, experience with electrons, and possibilities - and its limitations for accelerating ions are reviewed. A number of proton induction linac designs are examined with the LIACEP program and general conclusions are given. Results suggest that a proton induction accelerator of the lowest voltage, consistent with good neutron flux, is preferred and could well be cost competitive with the usual rf linac/storage ring designs. (orig.)

Inductive acquisition of expert knowledge

Energy Technology Data Exchange (ETDEWEB)

Muggleton, S.H.

1986-01-01

Expert systems divide neatly into two categories: those in which (1) the expert decisions result in changes to some external environment (control systems), and (2) the expert decisions merely seek to describe the environment (classification systems). Both the explanation of computer-based reasoning and the bottleneck (Feigenbaum, 1979) of knowledge acquisition are major issues in expert-systems research. The author contributed to these areas of research in two ways: 1. He implemented an expert-system shell, the Mugol environment, which facilitates knowledge acquisition by inductive inference and provides automatic explanation of run-time reasoning on demand. RuleMaster, a commercial version of this environment, was used to advantage industrially in the construction and testing of two large classification systems. 2. He investigated a new techniques called 'sequence induction' that can be used in construction of control systems. Sequence induction is based on theoretical work in grammatical learning. He improved existing grammatical learning algorithms as well as suggesting and theoretically characterizing new ones. These algorithms were successfully applied to acquisition of knowledge for a diverse set of control systems, including inductive construction of robot plans and chess end-gam strategies.

The myth of induction in qualitative nursing research.

Science.gov (United States)

Bergdahl, Elisabeth; Berterö, Carina M

2015-04-01

In nursing today, it remains unclear what constitutes a good foundation for qualitative scientific inquiry. There is a tendency to define qualitative research as a form of inductive inquiry; deductive practice is seldom discussed, and when it is, this usually occurs in the context of data analysis. We will look at how the terms 'induction' and 'deduction' are used in qualitative nursing science and by qualitative research theorists, and relate these uses to the traditional definitions of these terms by Popper and other philosophers of science. We will also question the assertion that qualitative research is or should be inductive. The position we defend here is that qualitative research should use deductive methods. We also see a need to understand the difference between the creative process needed to create theory and the justification of a theory. Our position is that misunderstandings regarding the philosophy of science and the role of inductive and deductive logic and science are still harming the development of nursing theory and science. The purpose of this article is to discuss and reflect upon inductive and deductive views of science as well as inductive and deductive analyses in qualitative research. We start by describing inductive and deductive methods and logic from a philosophy of science perspective, and we examine how the concepts of induction and deduction are often described and used in qualitative methods and nursing research. Finally, we attempt to provide a theoretical perspective that reconciles the misunderstandings regarding induction and deduction. Our conclusion is that openness towards deductive thinking and testing hypotheses is needed in qualitative nursing research. We must also realize that strict induction will not create theory; to generate theory, a creative leap is needed. © 2014 John Wiley & Sons Ltd.

Factors predicting labor induction success: a critical analysis.

Science.gov (United States)

Crane, Joan M G

2006-09-01

Because of the risk of failed induction of labor, a variety of maternal and fetal factors as well as screening tests have been suggested to predict labor induction success. Certain characteristics of the woman (including parity, age, weight, height and body mass index), and of the fetus (including birth weight and gestational age) are associated with the success of labor induction; with parous, young women who are taller and lower weight having a higher rate of induction success. Fetuses with a lower birth weight or increased gestational age are also associated with increased induction success. The condition of the cervix at the start of induction is an important predictor, with the modified Bishop score being a widely used scoring system. The most important element of the Bishop score is dilatation. Other predictors, including transvaginal ultrasound (TVUS) and biochemical markers [including fetal fibronectin (fFN)] have been suggested. Meta-analyses of studies identified from MEDLINE, PubMed, and EMBASE and published from 1990 to October 2005 were performed evaluating the use of TVUS and fFN in predicting labor induction success in women at term with singleton gestations. Both TVUS and Bishop score predicted successful induction [likelihood ratio (LR)=1.82, 95% confidence interval (CI)=1.51-2.20 and LR=2.10, 95%CI=1.67-2.64, respectively]. As well, fFN and Bishop score predicted successful induction (LR=1.49, 95%CI=1.20-1.85, and LR=2.62, 95%CI=1.88-3.64, respectively). Although TVUS and fFN predicted successful labor induction, neither has been shown to be superior to Bishop score. Further research is needed to evaluate these potential predictors and insulin-like growth factor binding protein-1 (IGFBP-1), another potential biochemical marker.

Knowledge, expectations, and inductive reasoning within conceptual hierarchies.

Science.gov (United States)

Coley, John D; Hayes, Brett; Lawson, Christopher; Moloney, Michelle

2004-01-01

Previous research (e.g. Cognition 64 (1997) 73) suggests that the privileged level for inductive inference in a folk biological conceptual hierarchy does not correspond to the "basic" level (i.e. the level at which concepts are both informative and distinct). To further explore inductive inference within conceptual hierarchies, we examine relations between knowledge of concepts at different hierarchical levels, expectations about conceptual coherence, and inductive inference. In Experiments 1 and 2, 5- and 8-year-olds and adults listed features of living kind (Experiments 1 and 2) and artifact (Experiment 2) concepts at different hierarchical levels (e.g. plant, tree, oak, desert oak), and also rated the strength of generalizations to the same concepts. For living kinds, the level that showed a relative advantage on these two tasks differed; the greatest increase in features listed tended to occur at the life-form level (e.g. tree), whereas the greatest increase in inductive strength tended to occur at the folk-generic level (e.g. oak). Knowledge and induction also showed different developmental trajectories. For artifact concepts, the levels at which the greatest gains in knowledge and induction occurred were more varied, and corresponded more closely across tasks. In Experiment 3, adults reported beliefs about within-category similarity for concepts at different levels of animal, plant and artifact hierarchies, and rated inductive strength as before. For living kind concepts, expectations about category coherence predicted patterns of inductions; knowledge did not. For artifact concepts, both knowledge and expectations predicted patterns of induction. Results suggest that beliefs about conceptual coherence play an important role in guiding inductive inference, that this role may be largely independent of specific knowledge of concepts, and that such beliefs are especially important in reasoning about living kinds.

Microcontroller based PWM controlled four switch three phase inverter fed induction motor drive

Directory of Open Access Journals (Sweden)

Mohanty Kant Nalin

2010-01-01

Full Text Available This paper presents PIC microcontroller based PWM inverter controlled four switch three phase inverter (FSTPI fed Induction Motor drive. The advantage of this inverter that uses of 4 switches instead of conventional 6 switches is lesser switching losses, lower electromagnetic interference (EMI, less complexity of control algorithms and reduced interface circuits. Simulation and experimental work are carried out and results presented to demonstrate the feasibility of the proposed approach. Simulation is carried out using MATLAB SIMULINK and in the experimental work a prototype model is built to verify the simulation results. PIC microcontroller (PIC 16F877A is used to generate the PWM pulses for FSTPI to drive the 0.5 hp 3-phase Induction Motor.

Lysogenic induction in Lex Al Escherichia coli mutants: characterization of the induction and prophage repressor influence

International Nuclear Information System (INIS)

Carvalho, R.E.S.

1982-01-01

SOS functions require new synthesis of protein and have been described as dependent on both the rec A and lex A genes. The induction of prophage was studied in bacterial strains lysogenic for a series of phages which synthesize different levels of repressor (λ, λ i m m 4 3 4 J and λ i m m 4 3 4 T ) and was compared to W-reactivation. Prophage induction was detected in lex Al mutants although at a slightly lower level and requiring two times longer when compared with wild-type. The optimum UV-dose for induction differed for each lysogenic strain and correlated with the level of repressor

Inductance position sensor for pneumatic cylinder

Science.gov (United States)

Ripka, Pavel; Chirtsov, Andrey; Mirzaei, Mehran; Vyhnanek, Jan

2018-04-01

The position of the piston in pneumatic cylinder with aluminum wall can be measured by external inductance sensor without modifications of the aluminum piston and massive iron piston rod. For frequencies below 20 Hz the inductance is increasing with inserting rod due to the rod permeability. This mode has disadvantage of slow response to piston movement and also high temperature sensitivity. At the frequency of 45 Hz the inductance is position independent, as the permeability effect is compensated by the eddy current effect. At higher frequencies eddy current effects in the rod prevail, the inductance is decreasing with inserting rod. In this mode the sensitivity is smaller but the sensor response is fast and temperature stability is better. We show that FEM simulation of this sensor using measured material properties gives accurate results, which is important for the sensor optimization such as designing the winding geometry for the best linearity.

Multilayered Regulation of Ethylene Induction Plays a Positive Role in Arabidopsis Resistance against Pseudomonas syringae.

Science.gov (United States)

Guan, Rongxia; Su, Jianbin; Meng, Xiangzong; Li, Sen; Liu, Yidong; Xu, Juan; Zhang, Shuqun

2015-09-01

Ethylene, a key phytohormone involved in plant-pathogen interaction, plays a positive role in plant resistance against fungal pathogens. However, its function in plant bacterial resistance remains unclear. Here, we report a detailed analysis of ethylene induction in Arabidopsis (Arabidopsis thaliana) in response to Pseudomonas syringae pv tomato DC3000 (Pst). Ethylene biosynthesis is highly induced in both pathogen/microbe-associated molecular pattern (PAMP)-triggered immunity and effector-triggered immunity (ETI), and the induction is potentiated by salicylic acid (SA) pretreatment. In addition, Pst actively suppresses PAMP-triggered ethylene induction in a type III secretion system-dependent manner. SA potentiation of ethylene induction is dependent mostly on MITOGEN-ACTIVATED PROTEIN KINASE6 (MPK6) and MPK3 and their downstream ACS2 and ACS6, two type I isoforms of 1-aminocyclopropane-1-carboxylic acid synthases (ACSs). ACS7, a type III ACS whose expression is enhanced by SA pretreatment, is also involved. Pst expressing the avrRpt2 effector gene (Pst-avrRpt2), which is capable of triggering ETI, induces a higher level of ethylene production, and the elevated portion is dependent on SALICYLIC ACID INDUCTION DEFICIENT2 and NONEXPRESSER OF PATHOGENESIS-RELATED GENE1, two key players in SA biosynthesis and signaling. High-order ACS mutants with reduced ethylene induction are more susceptible to both Pst and Pst-avrRpt2, demonstrating a positive role of ethylene in plant bacterial resistance mediated by both PAMP-triggered immunity and ETI. © 2015 American Society of Plant Biologists. All Rights Reserved.

Intrinsic magnetic torque at low magnetic induction

International Nuclear Information System (INIS)

Doria, M.M.; Oliveira, I.G. de.

1993-01-01

Using anisotropic London theory the intrinsic magnetic torque for extreme type II uniaxial superconductors for any value of the magnetic induction is obtained. It is considered the vortex lines straight and take into account the contribution of the supercurrents flowing inside the vortex core within the London theory. It is shown that the interline and intra line free energies give opposite torque contributions, the first drives the magnetic induction parallel to the superconductor's axis of symmetry and the second orthogonal to it. At high magnetic induction torque expression obtained generalizes V. Kogan's formula since it has no free parameters other than the anisotropy γ = m 1 /m 3 and the Ginzburg-Landau parameter κ. At low magnetic induction it is proposed a way to observe vortex chains effects in the total torque based on the fact that London theory is linear and the energy to make a single vortex line in space is independent of the magnetic induction. (author)

On line protection systems for induction motors

International Nuclear Information System (INIS)

Colak, I.; Celik, H.; Sefa, I.; Demirbas, S.

2005-01-01

Protection of induction motors is very important since they are widely used in industry for many applications due to their high robustness, reliability, low cost and maintenance, high efficiency and long service life. So, protecting these motors is crucial for operations. This paper presents a combined protection approach for induction motors. To achieve this, the electrical values of the induction motor were measured with sensitivity ±1% through a data acquisition card and processed with software developed in Visual C++. An on line protection system for induction motors was achieved easily and effectively. The experimental results have shown that the induction motor was protected against the possible problems faced during the operation. The software developed for this protection provides flexible and reliable media for operators and their motors. It is expected that the motor protection achieved in this study might be faster than the classical techniques and also may be applied to larger motors easily after small modifications of the software

Reasoning about modular datatypes with Mendler induction

Directory of Open Access Journals (Sweden)

Paolo Torrini

2015-09-01

Full Text Available In functional programming, datatypes a la carte provide a convenient modular representation of recursive datatypes, based on their initial algebra semantics. Unfortunately it is highly challenging to implement this technique in proof assistants that are based on type theory, like Coq. The reason is that it involves type definitions, such as those of type-level fixpoint operators, that are not strictly positive. The known work-around of impredicative encodings is problematic, insofar as it impedes conventional inductive reasoning. Weak induction principles can be used instead, but they considerably complicate proofs. This paper proposes a novel and simpler technique to reason inductively about impredicative encodings, based on Mendler-style induction. This technique involves dispensing with dependent induction, ensuring that datatypes can be lifted to predicates and relying on relational formulations. A case study on proving subject reduction for structural operational semantics illustrates that the approach enables modular proofs, and that these proofs are essentially similar to conventional ones.

Improvement the DTC system for electric vehicles induction motors

Directory of Open Access Journals (Sweden)

Arif Ali

2010-01-01

Full Text Available A three-phase squirrel-cage induction motor is used as a propulsion system of an electric vehicle (EV. Two different control methods have been designed. The first is based on the conventional DTC Scheme adapted for three level inverter. The second is based on the application of fuzzy logic controller to the DTC scheme. The motor is controlled at different operating conditions using a FLC based DTC technique. In the simulation the novel proposed technique reduces the torque and current ripples. The EV dynamics are taken into account.

Reduced rearing density increases postrelease migration success of Atlantic salmon (Salmo salar) smolts

DEFF Research Database (Denmark)

Larsen, Martin Hage; Johnsson, Jörgen I; Näslund, Joacim

2016-01-01

during rearing in the hatchery. However, individuals reared at reduced density had less eroded dorsal fins and opercula relative to those from the high-density treatment. In the stream, the downstream migration success was 16% higher for fish reared at reduced density than for conspecifics kept at high-density......The overall aim of this study was to investigate the effect of rearing density on the post-release survival of Atlantic salmon (Salmo salar) smolts during seaward migration. Fish were either reared at conventional hatchery density or at one-third of conventional density. Three hundred one-year old...... smolts from each density treatment were individually tagged with passive integrated transponder (PIT) tags and released 3.2 km upstream of a stationary antenna array in a natural stream. There were no significant differences in length, body mass, or condition between fish from the two density treatments...

Human HepaRG Cells can be Cultured in Hanging-drop Plates for Cytochrome P450 Induction and Function Assays.

Science.gov (United States)

Murayama, Norie; Usui, Takashi; Slawny, Nicky; Chesné, Christophe; Yamazaki, Hiroshi

2015-01-01

Recent guidance/guidelines for industry recommend that cytochrome P450 induction can be assessed using human hepatocyte enzyme activity and/or mRNA levels to evaluate potential drug- drug interactions. To evaluate time-dependent cytochrome P450 induction precisely, induction of CYP1A2, CYP2B6, and CYP3A4 mRNA was confirmed (>2-fold) by the treatment with omeprazole, phenobarbital, and rifampicin, respectively, for 24 or 48 h on day 3 from the start of culture. After 24 h, the fold induction of CYP1A2 with 3.6 and 1.8x10(4) HepaRG cells per well was lower than that for 7.2x10(4) cells. CYP1A2 induction levels at 24 h were higher than those after 48 h. In contrast, higher CYP2B6 inductions were confirmed after 48 h exposure than after 24 h, independent of the number of cells per well. To help reduce the use of human cryopreserved hepatocytes, typical P450-dependent enzyme activities were investigated in human HepaRG cells cultured in commercial hanging-drop plates. Newly designed 96-well hanging-drop plates were capable of maintaining human CYP3A-dependent midazolam hydroxylation activities for up to 4 days using only 10% of the recommended initial 7.2x10(4) cells per well. Favorable HepaRG function using hanging-drop plates was confirmed by detecting 1'- hydroxymidazolam O-glucuronide on day 3, suggesting an improvement over traditional control plates in which this metabolite can be detected for 24-well plates. These results suggest that the catalytic function and/or induction of CYP1A2, CYP2B6, and CYP3A4 can be readily assessed with reduced numbers of starting HepaRG cells cultured in three-dimensional cultures in drops prepared with hanging-drop plates.

Fast and accurate inductance and coupling calculation for a multi-layer Nb process

International Nuclear Information System (INIS)

Fourie, Coenrad J; Takahashi, Akitomo; Yoshikawa, Nobuyuki

2015-01-01

Currently, fabrication processes for superconductive integrated circuits are moving to multiple wiring and shielding layers, some of which are placed below the main ground plane (GP) and device layers. The Advanced Industrial Science and Technology advanced process (ADP2) was the first such multi-layer Nb process with planarized passive transmission line and GP layers below the junction layer, and is at the time of writing still the most developed. This process allows complex circuit designs, and accurate inductance extraction helps to push the boundaries of the layouts possible. We show that the position of ground connections between ground layers influences the inductance of structures for which these GPs act as return path, and that this needs to be accounted for in modelling. However, due to the number of wiring layers and GPs, full layout modelling of large cells causes long calculation times. In this paper we discuss methods with which to reduce model size, and calibrate InductEx calculations using these methods against measured results. We show that model reduction followed by calibration results in fast calculation times while good accuracy is maintained. We also show that InductEx correctly handles coupling between conductors in a multi-layer layout, and how to model layouts to gauge unwanted coupling between power lines and single flux quantum electronics. (paper)

Inductive Reasoning About Effectful Data Types

DEFF Research Database (Denmark)

Filinski, Andrzej; Støvring, Kristian

2007-01-01

We present a pair of reasoning principles, definition and proof by rigid induction, which can be seen as proper generalizations of lazy-datatype induction to monadic effects other than partiality. We further show how these principles can be integrated into logical-relations arguments, and obtain...

Inductance and resistance measurement method for vessel detection and coil powering in all-surface inductive heating systems composed of outer squircle coils

Science.gov (United States)

Kilic, Veli Tayfun; Unal, Emre; Demir, Hilmi Volkan

2017-05-01

In this work, we investigate a method proposed for vessel detection and coil powering in an all-surface inductive heating system composed of outer squircle coils. Besides conventional circular coils, coils with different shapes such as outer squircle coils are used for and enable efficient all-surface inductive heating. Validity of the method, which relies on measuring inductance and resistance values of a loaded coil at different frequencies, is experimentally demonstrated for a coil with shape different from conventional circular coil. Simple setup was constructed with a small coil to model an all-surface inductive heating system. Inductance and resistance maps were generated by measuring coil's inductance and resistance values at different frequencies loaded by a plate made of different materials and located at various positions. Results show that in an induction hob for various coil geometries it is possible to detect a vessel's presence, to identify its material type and to specify its position on the hob surface by considering inductance and resistance of the coil measured on at least two different frequencies. The studied method is important in terms of enabling safe, efficient and user flexible heating in an all-surface inductive heating system by automatically detecting the vessel's presence and powering on only the coils that are loaded by the vessel with predetermined current levels.

Structural Design Optimization of Doubly-Fed Induction Generators Using GeneratorSE

Energy Technology Data Exchange (ETDEWEB)

Sethuraman, Latha [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Fingersh, Lee J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dykes, Katherine L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Arthurs, Claire [Georgia Institute of Technology

2017-11-13

A wind turbine with a larger rotor swept area can generate more electricity, however, this increases costs disproportionately for manufacturing, transportation, and installation. This poster presents analytical models for optimizing doubly-fed induction generators (DFIGs), with the objective of reducing the costs and mass of wind turbine drivetrains. The structural design for the induction machine includes models for the casing, stator, rotor, and high-speed shaft developed within the DFIG module in the National Renewable Energy Laboratory's wind turbine sizing tool, GeneratorSE. The mechanical integrity of the machine is verified by examining stresses, structural deflections, and modal properties. The optimization results are then validated using finite element analysis (FEA). The results suggest that our analytical model correlates with the FEA in some areas, such as radial deflection, differing by less than 20 percent. But the analytical model requires further development for axial deflections, torsional deflections, and stress calculations.

Eisenstein integrals and induction of relations

NARCIS (Netherlands)

Ban, E.P. van den

2004-01-01

A survey of joint work with Henrik Schlichtkrull on the induction of certain relations among (partial) Eisenstein integrals for the minimal principal series of a reductive symmetric space is given. The application of this principle of induction to the proof of the Fourier inversion formula in

A Framework of Mathematics Inductive Reasoning

Science.gov (United States)

Christou, Constantinos; Papageorgiou, Eleni

2007-01-01

Based on a synthesis of the literature in inductive reasoning, a framework for prescribing and assessing mathematics inductive reasoning of primary school students was formulated and validated. The major constructs incorporated in this framework were students' cognitive abilities of finding similarities and/or dissimilarities among attributes and…

Diagnostics for induction accelerators

International Nuclear Information System (INIS)

Fessenden, T.J.

1996-04-01

The induction accelerator was conceived by N. C. Christofilos and first realized as the Astron accelerator that operated at LLNL from the early 1960's to the end of 1975. This accelerator generated electron beams at energies near 6 MeV with typical currents of 600 Amperes in 400 ns pulses. The Advanced Test Accelerator (ATA) built at Livermore's Site 300 produced 10,000 Ampere beams with pulse widths of 70 ns at energies approaching 50 MeV. Several other electron and ion induction accelerators have been fabricated at LLNL and LBNL. This paper reviews the principal diagnostics developed through efforts by scientists at both laboratories for measuring the current, position, energy, and emittance of beams generated by these high current, short pulse accelerators. Many of these diagnostics are closely related to those developed for other accelerators. However, the very fast and intense current pulses often require special diagnostic techniques and considerations. The physics and design of the more unique diagnostics developed for electron induction accelerators are presented and discussed in detail

Inductance position sensor for pneumatic cylinder

Directory of Open Access Journals (Sweden)

Pavel Ripka

2018-04-01

Full Text Available The position of the piston in pneumatic cylinder with aluminum wall can be measured by external inductance sensor without modifications of the aluminum piston and massive iron piston rod. For frequencies below 20 Hz the inductance is increasing with inserting rod due to the rod permeability. This mode has disadvantage of slow response to piston movement and also high temperature sensitivity. At the frequency of 45 Hz the inductance is position independent, as the permeability effect is compensated by the eddy current effect. At higher frequencies eddy current effects in the rod prevail, the inductance is decreasing with inserting rod. In this mode the sensitivity is smaller but the sensor response is fast and temperature stability is better. We show that FEM simulation of this sensor using measured material properties gives accurate results, which is important for the sensor optimization such as designing the winding geometry for the best linearity.

Similarity, Induction, Naming, and Categorization (SINC): Generalization or Inductive Reasoning? Reply to Heit and Hayes (2005)

Science.gov (United States)

Sloutsky, Vladimir M.; Fisher, Anna V.

2006-01-01

This article is a response to E. Heit and B. K. Hayes's comment on the target article "Induction and Categorization in Young Children: A Similarity-Based Model" (V. M. Sloutsky & A. V. Fisher, 2004a). The response discusses points of agreement and disagreement with Heit and Hayes; phenomena predicted by similarity, induction, naming, and…

Swaziland : Reducing Poverty Through Shared Growth

OpenAIRE

World Bank

2000-01-01

The people of Swaziland are its greatest resource. Yet, social and economic indicators of household welfare converge to confirm fundamental inequalities in access to incomes and assets, and the existence of significant poverty and deprivation. Furthermore, as the regional economic and social climate is transformed, the fragile gains of the past are being fast eroded. At this historic junct...

Towards prediction of soil erodibility using hyperspectral information: a case study in a semi-arid region of Iran

DEFF Research Database (Denmark)

Ostovari, Yaser; Ghorbani-Dashtaki, Shoja; Bahrami, Hossein-Ali

2018-01-01

and develop Spectrotransfer Function (STF) using spectral reflectance information and Pedotransfer Function (PTF) to predict the K-factor, respectively. The derived STF was compared with developed PTF using measurable soil properties by Ostovari et al. (2016) and the Universal Soil Loss Equation (USLE......Soil Visible–Near-Infrared (Vis-NIR) spectroscopy has become an applicable and interesting technique to evaluate a number of soil properties because it is a fast, cost-effective, and non-invasive measurement technique. The main objective of the study to predict soil erodibility (K-factor), soil...... organic matter (SOM), and calcium carbonate equivalent (CaCO3) in calcareous soils of semi-arid regions located in south of Iran using spectral reflectance information in the Vis-NIR range. The K-factor was measured in 40 erosion plots under natural rainfall and the spectral reflectance of soil samples...

The Effect of a Brief Mindfulness Induction on Processing of Emotional Images: an ERP Study

Directory of Open Access Journals (Sweden)

Marianna D. Eddy

2015-09-01

Full Text Available The ability to effectively direct one’s attention is an important aspect of regulating emotions and a component of mindfulness. Mindfulness practices have been established as effective interventions for mental and physical illness; however, the underlying neural mechanisms of mindfulness and how they relate to emotional processing have not been explored in depth. The current study used a within-subjects repeated measures design to examine if focused breathing, a brief mindfulness induction, could modulate event-related potentials (ERPs during emotional image processing relative to a control condition. We related ERP measures of processing positive, negative, and neutral images (the P300 and late posterior positivity – LPP to state and trait mindfulness measures. Overall, the brief mindfulness induction condition did not influence ERPs reflecting emotional processing; however, in the brief mindfulness induction condition, those participants who reported feeling more decentered (a subscale of the Toronto Mindfulness Scale after viewing the images had reduced P300 responses to negative versus neutral images.

The effect of a brief mindfulness induction on processing of emotional images: an ERP study.

Science.gov (United States)

Eddy, Marianna D; Brunyé, Tad T; Tower-Richardi, Sarah; Mahoney, Caroline R; Taylor, Holly A

2015-01-01

The ability to effectively direct one's attention is an important aspect of regulating emotions and a component of mindfulness. Mindfulness practices have been established as effective interventions for mental and physical illness; however, the underlying neural mechanisms of mindfulness and how they relate to emotional processing have not been explored in depth. The current study used a within-subjects repeated measures design to examine if focused breathing, a brief mindfulness induction, could modulate event-related potentials (ERPs) during emotional image processing relative to a control condition. We related ERP measures of processing positive, negative, and neutral images (the P300 and late positive potential - LPP) to state and trait mindfulness measures. Overall, the brief mindfulness induction condition did not influence ERPs reflecting emotional processing; however, in the brief mindfulness induction condition, those participants who reported feeling more decentered (a subscale of the Toronto Mindfulness Scale) after viewing the images had reduced P300 responses to negative versus neutral images.

Role of oxygen free radicals in the induction of sister chromatid exchanges by cigarette smoke

International Nuclear Information System (INIS)

Lee, C.K.; Brown, B.G.; Rice, W.Y. Jr.; Doolittle, D.J.

1989-01-01

Cigarette smoke has been reported to contain free radicals and free radical generators in both the gas and particulate phases. Studies in our laboratory have shown that both cigarette smoke condensate (CSC) and smoke bubbled through phosphate buffered saline solution (smoke-PBS) increased sister chromatid exchanges (SCE) in Chinese hamster ovary cells in a dose-dependent manner. Since oxygen free radicals have been shown to cause SCEs and other chromosomal damage, we investigated the role of these radicals in the induction of SCEs by CSC and smoke-PBS. Addition of the antioxidant enzymes catalase and superoxide dismutase or the oxygen-radical scavenger ascorbic acid failed to reduce the SCE frequency in the presence of either CSC or smoke-PBS. Additional studies indicated that the quantity of hydrogen peroxide produced in CSC or smoke-PBS is too small to account for the observed SCE induction. It appears, therefore, that SCE induction by CSC or smoke-PBS does not involve the participation of oxygen free radicals

Modeling of Lossy Inductance in Moving-Coil Loudspeakers

DEFF Research Database (Denmark)

Kong, Xiao-Peng; Agerkvist, Finn T.; Zeng, Xin-Wu

2015-01-01

The electrical impedance of moving-coil loudspeakers is dominated by the lossy inductance in high frequency range. Using the equivalent electrical circuit method, a new model for the lossy inductance based on separate functions for the magnitude and phase of the impedance is presented. The electr......The electrical impedance of moving-coil loudspeakers is dominated by the lossy inductance in high frequency range. Using the equivalent electrical circuit method, a new model for the lossy inductance based on separate functions for the magnitude and phase of the impedance is presented...

Rethinking Reinforcement: Allocation, Induction, and Contingency

Science.gov (United States)

Baum, William M

2012-01-01

The concept of reinforcement is at least incomplete and almost certainly incorrect. An alternative way of organizing our understanding of behavior may be built around three concepts: allocation, induction, and correlation. Allocation is the measure of behavior and captures the centrality of choice: All behavior entails choice and consists of choice. Allocation changes as a result of induction and correlation. The term induction covers phenomena such as adjunctive, interim, and terminal behavior—behavior induced in a situation by occurrence of food or another Phylogenetically Important Event (PIE) in that situation. Induction resembles stimulus control in that no one-to-one relation exists between induced behavior and the inducing event. If one allowed that some stimulus control were the result of phylogeny, then induction and stimulus control would be identical, and a PIE would resemble a discriminative stimulus. Much evidence supports the idea that a PIE induces all PIE-related activities. Research also supports the idea that stimuli correlated with PIEs become PIE-related conditional inducers. Contingencies create correlations between “operant” activity (e.g., lever pressing) and PIEs (e.g., food). Once an activity has become PIE-related, the PIE induces it along with other PIE-related activities. Contingencies also constrain possible performances. These constraints specify feedback functions, which explain phenomena such as the higher response rates on ratio schedules in comparison with interval schedules. Allocations that include a lot of operant activity are “selected” only in the sense that they generate more frequent occurrence of the PIE within the constraints of the situation; contingency and induction do the “selecting.” PMID:22287807

Use of misoprostol for induction of labour in unvaorable cervix in eclampsia

International Nuclear Information System (INIS)

Nahar, S.; Begum, S.; Yansur, S.; Rasul, C.H.

2004-01-01

Objective: To find out safety and efficiency of Misoprostol in cervical ripening and induction of labour to achieve vaginal delivery. Results: From Misoprostol insertion to delivery time was 4-24 hours. Vaginal delivery was achieved in 80.2%, which included spontaneous, forceps and vacuum extraction. Caesarean section rate was 19.7%. Indications for C. Section included Misoprostol unresponsiveness 11% and fetal distress in 8.6%. Oxytocin augmentation was required in 32% of cases. Term babies were 58%. Intrauterine death and neonatal deaths were 9.8% and 8.6% respectively. Hyper stimulation and postpartum haemorrhage was seen in 2.4% and 3.7% of patients respectively. Conclusion: intravaginal Misoprostol is well tolerated and is very effective for the induction of labour in eclampsia. It helps vaginal delivery in toxemic patients, reduces maternal morbidity, mortality and hospital stay. (author)

Road infrastructure and demand induction

DEFF Research Database (Denmark)

Nielsen, Thomas Alexander Sick; Hovgesen, Henrik Harder; Lahrmann, Harry

2006-01-01

a long screenline is used to measure the development in aggregate demand in selected corridors. The paper analyses demand induction by establishing time series of aggregate demand that is compared with the national traffic index. Significant trend breaks in the association between aggregate demand...... in the corridors and the national index, following the opening of motorways or bridges, indicates demand induction by infrastructure expansion in a number of instances. Lack of significant trend breaks following opening year is found in peripheral areas where major population centres are missing. This indicates...... the necessity of some latent demand within suitable travel range for new infrastructure elements to produce significant amounts of induced demand. Estimates of demand induction as a percentage of the realised demand five years after opening are between 10% and 67% for new motorway sections depending...

1 MV low-induction pulse generator

International Nuclear Information System (INIS)

Koba, G.I.; Koba, Yu.V.; Slivkov, I.N.; Sukhov, A.D.; Tarumov, Eh.Z.

1980-01-01

A high-voltage pulse generator is described. The generator Uses the Arkadiev-Marx circuit at 1 MV voltage and 12 kJ energy; the inductance of the discharge circuit is 1.3 μN. Low inductance of the generator has been obtained due to the use of low-inductance capacitors and employment of bifilar buses with oil barrier insulation. To provide reliable generator triggering, an ignition circuit has been developed with a resistive coupling between generator steps, based on controlled three-electrode sparkgaps with a distorted field. The generator switching time is slightly dependent on pressure and constitutes 200-300 ns. The generator efficiency is 83%

Thermo-hydrodynamic and inductive modelling of a glass melt elaborated in cold inductive crucible

International Nuclear Information System (INIS)

Sauvage, E.

2009-11-01

Within the context of a search for a new vitrification process for nuclear wastes with a replacement of the presently used metallic pot by an inductive cold crucible, this research thesis deals with the numerical modelling of this technology. After having recalled the interest of nuclear waste vitrification, this report presents the new process based on the use of a cold crucible, describing principles and objectives of this method, and the characteristic physical phenomena associated with the flow and the thermodynamics of the glassy melt in such a crucible. It also recalls and comments the existing works on modelling. The main objective of this research is then to demonstrate the feasibility of 3D thermo-hydraulic and inductive simulations. He describes and analyses the glass physical properties (electrical properties, viscosity, thermal properties), the electromagnetic, hydrodynamic and thermal phenomena. He presents in detail the bubbling mixing modelling, reports 3D induction and fluid mechanical coupling calculations, and specific thermal investigations (radiating transfers, thermal limit conditions)

Mixed function oxidase induction in Carcinus aestuarii. Field and experimental studies for the evaluation of toxicological risk due to Mediterranean contaminants

International Nuclear Information System (INIS)

Fossi, M.C.; Savelli, C.; Casini, S.

1998-01-01

The aim of this study was to test and validate the use of mixed function oxidase (MFO) induction, in the crab Carcinus aestuarii, under experimental and field studies, for the evaluation of toxicological risk due to the main contaminants in the Mediterranean. Two different experiments were performed in the laboratory in order to identify the most suitable tissues for MFO studies in this species and the most suitable and sensitive MFO responses for evaluating chemical stress due to lipophilic contaminants. In order to validate this methodology in the field, two studies were carried out in two polluted Mediterranean lagoons: a transplant experiment in Orbetello Lagoon and an in situ experiment in Venice Lagoon. The following MFO responses were investigated in hepatopancres and gills of the crabs: ethoxyresorufin-O-deethylase (EROD) and benzo(a)pyrene hydroxylase (BPH) activities and reductase enzyme activities. The main results can be summarised as follows: midgut-gland and gills were confirmed to be useful for MFO tests; BPH activity in hepatopancreas was the most suitable and sensitive MFO response for evaluating chemical stress due to Mediterranean contaminants in laboratory and field studies; in the Orbetello Lagoon experiment, a statistically significant difference was found between sites subject to different human impact. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

Temporal kinetics and concentration-response relationships for induction of CYP1A, CYP2B, and CYP3A in primary cultures of beagle dog hepatocytes.

Science.gov (United States)

Graham, Richard A; Tyler, Lindsey O; Krol, Wojciech L; Silver, Ivin S; Webster, Lindsey O; Clark, Philip; Chen, Liangfu; Banks, Troy; LeCluyse, Edward L

2006-01-01

Compared to other species, little information is available on the xenobiotic-induced regulation of cytochrome P450 enzymes in the beagle dog. Dogs are widely used in the pharmaceutical industry for many study types, including those that will impact decisions on compound progression. The purpose of this study was (1) to determine the temporal kinetics of drug-induced changes in canine CYP1A, CYP2B, and CYP3A mRNA and enzymatic activity, and (2) to characterize concentration-response relationships for CYP1A2, CYP2B11, and CYP3A12 using primary cultures of canine hepatocytes treated with beta-naphthoflavone (BNF), phenobarbital (PB), and rifampin (RIF), respectively. CYP1A1 and CYP1A2 mRNA exhibited maximal expression (12,700-fold and 206-fold, respectively) after 36 h of treatment with BNF. PB treatment, but not RIF treatment, caused maximal induction of CYP2B11 mRNA (149-fold) after 48 h of treatment. CYP3A12 and CYP3A26 mRNA levels were increased maximally after 72 h of treatment with PB and RIF (CYP3A12, 35-fold and 18-fold, and CYP3A26, 72-fold and 22-fold with PB and RIF treatment, respectively). Concentration-response relationships for BNF induced 7-ethoxyresorufin O-dealkylation (EROD) (EC(50) = 7.8 +/- 4.2 microM), PB induced 7-benzyloxyresorufin O-dealkylation (BROD) (EC(50) = 123 +/- 30 microM), and PB and RIF induced testosterone 6beta-hydroxylation (EC(50) = 132 +/- 28 microM and 0.98 +/- 0.16 microM) resembled the relationship for human CYP induction compared to that of rodent. Interestingly, RIF had no effect on CYP2B11 expression, which represents a species difference overlooked in previous investigations. Overall, the induction of dog CYP1A, CYP2B, and CYP3A exhibits characteristics that are intermediate to those of rodent and human. (c) 2006 Wiley Periodicals, Inc.

Coreless Concept for High Gradient Induction Cell

International Nuclear Information System (INIS)

Krasnykh, Anatoly

2008-01-01

An induction linac cell for a high gradient is discussed. The proposed solid state coreless approach for the induction linac topology (SLIM(reg s ign)) is based on nanosecond mode operation. This mode may have an acceleration gradient comparable with gradients of rf- accelerator structures. The discussed induction system has the high electric efficiency. The key elements are a solid state semiconductor switch and a high electric density dielectric with a thin section length. The energy in the induction system is storied in the magnetic field. The nanosecond current break-up produces the high voltage. The induced voltage is used for acceleration. This manner of an operation allows the use of low voltage elements in the booster part and achieves a high accelerating gradient. The proposed topology was tested in POP (proof of principle) experiments

Prophage induction by ultraviolet light in Acinetobacter calcoaceticus

Energy Technology Data Exchange (ETDEWEB)

Berenstein, D.

1986-09-01

UV-induction of prophage P78 of Acinetobacter calcoaceticus increased with the UV-dose given to the lysogenic strain from the spontaneous induction frequency of about 0.8% to a maximal frequency of 10%. This 10- to 20-fold increase of induction frequency, as measured by the number of infective centres, was accompanied by a 1000-fold increase in the yield of free phage. This effect was probably due to an increase in burst size under the conditions of lysogenic induction. Unusually, the lysogen was more resistant to UV-irradiation than the corresponding non-lysogenic strain.

Prophage Induction by Ultraviolet Light in Acinetobacter calcoaceticus

DEFF Research Database (Denmark)

Berenstein, D.

1986-01-01

UV-induction of prophage P78 of Acinetobacter calcoaceticus increased with the UV-dose given to the lysogenic strain from the spontaneous induction frequency of about 0.8% to a maximal frequency of 10%. This 10- to 20-fold increase of induction frequency, as measured by the number of infective...... centres, was accompanied by a 1000-fold increase in the yield of free phage. This effect was probably due to an increase in burst size under the conditions of lysogenic induction. Unusually, the lysogen was more resistant to UV-irradiation than the corresponding non-lysogenic strain....

A Power-Efficient Wireless Capacitor Charging System Through an Inductive Link.

Science.gov (United States)

Lee, Hyung-Min; Ghovanloo, Maysam

2013-10-01

A power-efficient wireless capacitor charging system for inductively powered applications has been presented. A bank of capacitors can be directly charged from an ac source by generating a current through a series charge injection capacitor and a capacitor charger circuit. The fixed charging current reduces energy loss in switches, while maximizing the charging efficiency. An adaptive capacitor tuner compensates for the resonant capacitance variations during charging to keep the amplitude of the ac input voltage at its peak. We have fabricated the capacitor charging system prototype in a 0.35- μ m 4-metal 2-poly standard CMOS process in 2.1 mm 2 of chip area. It can charge four pairs of capacitors sequentially. While receiving 2.7-V peak ac input through a 2-MHz inductive link, the capacitor charging system can charge each pair of 1 μ F capacitors up to ±2 V in 420 μ s, achieving a high measured charging efficiency of 82%.

The Effect of Medium Chain Triglycerides on Time to Nutritional Ketosis and Symptoms of Keto-Induction in Healthy Adults: A Randomised Controlled Clinical Trial

Directory of Open Access Journals (Sweden)

Cliff J. d C. Harvey

2018-01-01

Full Text Available Medium chain triglycerides (MCTs are ketogenic and might reduce adverse effects of keto-induction and improve time to ketosis and the tolerability of very low carbohydrate diets. This study investigates whether MCT supplementation improves time to nutritional ketosis (NK, mood, and symptoms of keto-induction. We compared changes in beta-hydroxybutyrate (BOHB, blood glucose, symptoms of keto-induction, and mood disturbance, in 28 healthy adults prescribed a ketogenic diet, randomised to receive either 30 ml of MCT, or sunflower oil as a control, three times per day, for 20 days. The primary outcome measured was the achievement of NK (≥0.5 mmol·L−1 BOHB. Participants also completed a daily Profile of Mood States and keto-induction symptom questionnaire. MCT resulted in higher BOHB at all time points and faster time to NK, a result that failed to reach significance. Symptoms of keto-induction resulted from both diets, with a greater magnitude in the control group, except for abdominal pain, which occurred with greater frequency and severity in the MCT-supplemented diet. There was a possibly beneficial effect on symptoms by MCT, but the effect on mood was unclear. Based on these results, MCTs increase BOHB compared with LCT and reduce symptoms of keto-induction. It is unclear whether MCTs significantly improve mood or time to NK. The trial was registered by the Australia New Zealand Clinical Trial Registry ACTRN12616001099415.

Multilayered Regulation of Ethylene Induction Plays a Positive Role in Arabidopsis Resistance against Pseudomonas syringae1[OPEN

Science.gov (United States)

Guan, Rongxia; Su, Jianbin; Meng, Xiangzong; Li, Sen; Liu, Yidong; Xu, Juan; Zhang, Shuqun

2015-01-01

Ethylene, a key phytohormone involved in plant-pathogen interaction, plays a positive role in plant resistance against fungal pathogens. However, its function in plant bacterial resistance remains unclear. Here, we report a detailed analysis of ethylene induction in Arabidopsis (Arabidopsis thaliana) in response to Pseudomonas syringae pv tomato DC3000 (Pst). Ethylene biosynthesis is highly induced in both pathogen/microbe-associated molecular pattern (PAMP)-triggered immunity and effector-triggered immunity (ETI), and the induction is potentiated by salicylic acid (SA) pretreatment. In addition, Pst actively suppresses PAMP-triggered ethylene induction in a type III secretion system-dependent manner. SA potentiation of ethylene induction is dependent mostly on MITOGEN-ACTIVATED PROTEIN KINASE6 (MPK6) and MPK3 and their downstream ACS2 and ACS6, two type I isoforms of 1-aminocyclopropane-1-carboxylic acid synthases (ACSs). ACS7, a type III ACS whose expression is enhanced by SA pretreatment, is also involved. Pst expressing the avrRpt2 effector gene (Pst-avrRpt2), which is capable of triggering ETI, induces a higher level of ethylene production, and the elevated portion is dependent on SALICYLIC ACID INDUCTION DEFICIENT2 and NONEXPRESSER OF PATHOGENESIS-RELATED GENE1, two key players in SA biosynthesis and signaling. High-order ACS mutants with reduced ethylene induction are more susceptible to both Pst and Pst-avrRpt2, demonstrating a positive role of ethylene in plant bacterial resistance mediated by both PAMP-triggered immunity and ETI. PMID:26265775

UV induction of coliphage 186: Prophage induction as an SOS function

Energy Technology Data Exchange (ETDEWEB)

Lamont, I.; Brumby, A.M.; Egan, J.B.

1989-07-01

Our results show that UV induction of the 186 prophage depends upon the phage function Tum, with the mutant phenotype of turbid plaques on mitomycin plates and the expression of which is controlled by the host LexA protein. Tum function, encoded near the right-hand end of the coliphage 186 chromosome, is under the control of promoter p95. This promoter is overlapped by a sequence closely related to the consensus sequence of the LexA-binding site. It is proposed that inactivation of LexA after UV irradiation (or by genetic means) leads to prophage induction by permitting expression of Tum which, by unknown means, induces prophage. This mechanism is basically different from that seen with the UV-inducible lambdoid coliphages, which are not regulated by LexA.

Heterogeneity in pineapple fruit quality results from plant heterogeneity at flower induction.

Science.gov (United States)

Fassinou Hotegni, V Nicodème; Lommen, Willemien J M; Agbossou, Euloge K; Struik, Paul C

2014-01-01

Heterogeneity in fruit quality constitutes a major constraint in agri-food chains. In this paper the sources of the heterogeneity in pineapple in the field were studied in four experiments in commercial pineapple fields. The aims were to determine (a) whether differences in pineapple fruit quality among individual fruits are associated with differences in vigor of the individual plants within the crop at the time of artificial flower induction; and (b) whether the side shoots produced by the plant during the generative phase account for the fruit quality heterogeneity. Two pineapple cultivars were considered: cv. Sugarloaf and cv. Smooth Cayenne. Plant vigor at the time of artificial flower induction was measured by three variates: the number of functional leaves, the D-leaf length and their cross product. Fruit quality attributes measured at harvest time included external attributes (weight and height of fruit, infructescence and crown) and internal quality attributes [total soluble solids (TSS), pH, translucent flesh]. Results showed that the heterogeneity in fruit weight was a consequence of the heterogeneity in vigor of the plants at the moment of flower induction; that effect was mainly on the infructescence weight and less or not on the crown weight. The associations between plant vigor variates at flower induction and the internal quality attributes of the fruit were poor and/or not consistent across experiments. The weight of the slips (side shoots) explained part of the heterogeneity in fruit weight, infructescence weight and fruit height in cv. Sugarloaf. Possibilities for reducing the variation in fruit quality by precise cultural practices are discussed.

Heterogeneity in pineapple fruit quality results from plant heterogeneity at flower induction

Directory of Open Access Journals (Sweden)

V. Nicodeme eFassinou Hotegni

2014-12-01

Full Text Available Heterogeneity in fruit quality constitutes a major constraint in agri-food chains. In this paper the sources of the heterogeneity in pineapple in the field were studied in four experiments in commercial pineapple fields. The aims were to determine (a whether differences in pineapple fruit quality among individual fruits are associated with differences in vigor of the individual plants within the crop at the time of artificial flower induction; and (b whether the side shoots produced by the plant during the generative phase account for the fruit quality heterogeneity. Two pineapple cultivars were considered: cv. Sugarloaf and cv. Smooth Cayenne. Plant vigor at the time of artificial flower induction was measured by three variates: the number of functional leaves, the D-leaf length and their cross product. Fruit quality attributes measured at harvest time included external attributes (weight and height of fruit, infructescence and crown and internal quality attributes (total soluble solids, pH, translucent flesh. Results showed that the heterogeneity in fruit weight was a consequence of the heterogeneity in vigor of the plants at the moment of flower induction; that effect was mainly on the infructescence weight and less or not on the crown weight. The association between plant vigor variates at flower induction and the internal quality attributes of the fruit were poor and/or not consistent across experiments. The weight of the slips (side shoots, explained part of the heterogeneity in fruit weight, infructescence weight and fruit height in cv. Sugarloaf. Possibilities for reducing the variation in fruit quality by precise cultural practices are discussed.

[Popper and the problem of induction in epidemiology].

Science.gov (United States)

Banegas, J R; Rodríguez Artalejo, F; del Rey Calero, J

2000-01-01

or evidence. This is applicable both to statistical inference as well as to causal inference. We argue that the criteria of causality used in epidemiology are none other than rules of the method designed for the same purpose: they are concerned with eliminating or reducing errors (chance, bias...) on testing a causal hypothesis. Consequently, the so-called ausal inference, the step from evidence to causal theory, is not a logical inductive or probabilistic process but rather a decision based on the evaluation of a causal hypothesis thanks to methodological rules such as the criteria of causality. We believe that the interest of the debate between the Popperian and the inductivist epidemiologists is not merely a matter of words, as, if we are aware that we do not operate inductively, that we cannot establish firmly hypotheses, not even affirm them probabilistically, we will presumably adopt a humbler attitude and look more for the errors in our theories than for their facile examples of confirmation.

Mutation induction of roses through in vitro propagation

International Nuclear Information System (INIS)

Amran Abd Halim; Azhar Mohamad; Rusli Ibrahim

2002-01-01

The genus Rosa has been exploited for a variety used extensively in commercial production for many cultivars. Mutation induction is an alternative way of creating more variations in a single variety. Radiosensitivity test was carried out to identify optimum doses in mutation induction. Shoot tips of excises from in vitro plantlets were irradiated with doses of 0, 20, 40, 60, 80 and 100 Gy using a gamma cell with a 60 Co source at dose rate of 0.25 Gy s -1 . Irradiated shoot tips were cultured on semi solid modified Murashige and Skoog (MS) containing cytokinin (BAP) hormone and incubated at 24 with a photoperiod of 16 hours (3500 lux). Radiosensitivity was assessed by the rate of shoot proliferation four weeks after treatment. Increasing gamma ray doses caused a reduction of survival rate as well as the average shoots produced per plantlet. Through linear estimation of buds and shoots proliferation, radiation dose that reduced the growth to 50% of the control treatment (LD 50 ) was 53 Gy for miniature roses and 60 Gy for cut roses. Based on the radiosensitivity test 20 and 40 Gy were selected for irradiation to get new mutant varieties of roses. Changes in flower characters were found in three treated plants after three months in the green house. (Author)

A high-current racetrack induction accelerator

International Nuclear Information System (INIS)

Mondelli, A.; Roberson, C.W.

1983-01-01

In this paper, the energy and system scaling laws of the Racetrack Induction Accelerator are determined and its operating principles are discussed. This device is a cyclic accelerator that is capable of multi-kiloamp operation. Long pulse induction linac technology is used to obtain short acceleration times. The accelerator consists of a long-pulse linear induction module and a racetrack beam transport system. For detailed studies of the particle dynamics in a racetrack, a numerical model is required to integrate the fully-relativistic single-particle equations of motion in an externally applied magnetic field. The numerical model is a compromise between the need for a large rotational transform and the need for a reasonable volume within the separatrix

"GINEXMAL RCT: Induction of labour versus expectant management in gestational diabetes pregnancies"

Directory of Open Access Journals (Sweden)

Hadar Eran

2011-04-01

effective management to ameliorate maternal and neonatal outcomes. The primary objective is to determine whether caesarean section rate could be reduced among women undergoing induction of labour, in comparison to patients allocated to expectant monitoring. The secondary objective consists of the assessment and comparison of maternal and neonatal outcomes in the two study arms. Trial Registration The study protocol has been registered in the ClinicalTrials.gov Protocol Registration System, identification number NCT01058772.

Diagnostics for induction accelerators

International Nuclear Information System (INIS)

Fessenden, T.J.

1997-01-01

The induction accelerator was conceived by N. C. Christofilos and first realized as the Astron accelerator that operated at Lawrence Livermore National Laboratory (LLNL) from the early 1960s to the end of 1975. This accelerator generated electron beams at energies near 6 MeV with typical currents of 600 Amperes in 400-ns pulses. The Advanced Test Accelerator (ATA) built at Livermore close-quote s Site 300 produced 10,000-Ampere beams with pulse widths of 70 ns at energies approaching 50 MeV. Several other electron and ion induction accelerators have been fabricated at LLNL and Lawrence Berkeley National Laboratory (LBNL). This paper reviews the principal diagnostics developed through efforts by scientists at both laboratories for measuring the current, position, energy, and emittance of beams generated by these high-current, short-pulse accelerators. Many of these diagnostics are closely related to those developed for other accelerators. However, the very fast and intense current pulses often require special diagnostic techniques and considerations. The physics and design of the more unique diagnostics developed for electron induction accelerators are presented and discussed in detail. copyright 1997 American Institute of Physics

Energy-efficient induction motors designing with application of a modified criterion of reduced costs

Directory of Open Access Journals (Sweden)

V.S. Petrushin

2014-03-01

Full Text Available The paper introduces a modified criterion of reduced costs that employs coefficients of operation significance and priority of ohmic loss accounting to allow matching maximum efficiency with minimum reduced costs. Impact of the inflation factor on the criterion of reduced costs is analyzed.

Titrated Misoprostol Versus Dinoprostone for Labor Induction

African Journals Online (AJOL)

Aim: This study designed to compare titrated misoprostol regarding its safety and efficacy with dinoprostone for induction of labor. ... Statistical analysis done using Student's t-test for quantitative data and ..... induction: A pilot study. Rev Bras ...

How similar are recognition memory and inductive reasoning?

Science.gov (United States)

Hayes, Brett K; Heit, Evan

2013-07-01

Conventionally, memory and reasoning are seen as different types of cognitive activities driven by different processes. In two experiments, we challenged this view by examining the relationship between recognition memory and inductive reasoning involving multiple forms of similarity. A common study set (members of a conjunctive category) was followed by a test set containing old and new category members, as well as items that matched the study set on only one dimension. The study and test sets were presented under recognition or induction instructions. In Experiments 1 and 2, the inductive property being generalized was varied in order to direct attention to different dimensions of similarity. When there was no time pressure on decisions, patterns of positive responding were strongly affected by property type, indicating that different types of similarity were driving recognition and induction. By comparison, speeded judgments showed weaker property effects and could be explained by generalization based on overall similarity. An exemplar model, GEN-EX (GENeralization from EXamples), could account for both the induction and recognition data. These findings show that induction and recognition share core component processes, even when the tasks involve flexible forms of similarity.

Speed control of an induction motor by 6-switched 3-level inverter

Directory of Open Access Journals (Sweden)

Saygin Ali

2017-12-01

Full Text Available This paper presents speed control analysis of an induction motor by a 6-switched 3-level inverter. In the analysis of topology, the study used the field oriented control technique which is widely used in the literature, easy and stable for operating systems. The field weaking technique was used for speeds exceeding nominal speed to reduce magnetic saturation and thermal losses. At the end of the process, it was observed to increase motor torque and inverter efficiency. Instead of using 12 switches in conventional 3-level inverters, 6 switches are used in this topology. Reduced number of switches is the greatest contribution of this study.

Speed control of an induction motor by 6-switched 3-level inverter

Science.gov (United States)

Saygin, Ali; Kerem, Alper

2017-12-01

This paper presents speed control analysis of an induction motor by a 6-switched 3-level inverter. In the analysis of topology, the study used the field oriented control technique which is widely used in the literature, easy and stable for operating systems. The field weaking technique was used for speeds exceeding nominal speed to reduce magnetic saturation and thermal losses. At the end of the process, it was observed to increase motor torque and inverter efficiency. Instead of using 12 switches in conventional 3-level inverters, 6 switches are used in this topology. Reduced number of switches is the greatest contribution of this study.

Analyzing high school students' reasoning about electromagnetic induction

Science.gov (United States)

Jelicic, Katarina; Planinic, Maja; Planinsic, Gorazd

2017-06-01

Electromagnetic induction is an important, yet complex, physics topic that is a part of Croatian high school curriculum. Nine Croatian high school students of different abilities in physics were interviewed using six demonstration experiments from electromagnetism (three of them concerned the topic of electromagnetic induction). Students were asked to observe, describe, and explain the experiments. The analysis of students' explanations indicated the existence of many conceptual and reasoning difficulties with the basic concepts of electromagnetism, and especially with recognizing and explaining the phenomenon of electromagnetic induction. Three student mental models of electromagnetic induction, formed during the interviews, which reoccurred among students, are described and analyzed within the knowledge-in-pieces framework.

Integrated Cooling System for Induction Motor Traction Drives, CARAT Program Phase Two Final Report

Energy Technology Data Exchange (ETDEWEB)

Konrad, Charles E. [VPT, Inc., Blacksburg, VA (United States)

2002-12-03

This Program is directed toward improvements in electric vehicle/hybrid electric vehicle traction systems, and in particular, the development of a low cost, highly efficient, compact traction motor-controller system targeted for high volume automotive use. Because of the complex inter-relationships between the motor and the controller, the combination of motor and controller must be considered as a system in the design and evaluation of overall cost and performance. The induction motor is ideally suited for use as a traction motor because of its basic ruggedness, low cost, and high efficiency. As one can see in Figure 1.1, the induction motor traction drive has been continually evolving through a succession of programs spanning the past fifteen years. VPT marketed an induction motor-based traction drive system, the EV2000, which proved to be a reliable, high performance system that was used in a wide range of vehicles. The EV2000 drives evolved from the Modular Electric Vehicle Program (MEVP) and has been used in vehicles ranging in size from 3,000 lb. autos and utility vans, to 32,000 lb. city transit buses. Vehicles powered by the EV2000 induction motor powertrain have accumulated over 2 million miles of service. The EV2000 induction motor system represents 1993 state-of-the-art technology, and evolved from earlier induction motor programs that drove induction motor speeds up to 15,000 rpm to reduce the motor size and cost. It was recognized that the improvements in power density and motor cost sought in the PNGV program could only be achieved through increases in motor speed. Esson’s Rule for motor power clearly states that the power obtainable from a given motor design is the product of motor speed and volume. In order to meet the CARAT Program objectives, the maximum speed goal of the induction motor designed in this Program was increased from 15,000 rpm to 20,000 rpm while maintaining the efficiency and durability demonstrated by lower speed designs done in

Fault Diagnosis System of Induction Motors Based on Neural Network and Genetic Algorithm Using Stator Current Signals

Directory of Open Access Journals (Sweden)

Tian Han

2006-01-01

Full Text Available This paper proposes an online fault diagnosis system for induction motors through the combination of discrete wavelet transform (DWT, feature extraction, genetic algorithm (GA, and neural network (ANN techniques. The wavelet transform improves the signal-to-noise ratio during a preprocessing. Features are extracted from motor stator current, while reducing data transfers and making online application available. GA is used to select the most significant features from the whole feature database and optimize the ANN structure parameter. Optimized ANN is trained and tested by the selected features of the measurement data of stator current. The combination of advanced techniques reduces the learning time and increases the diagnosis accuracy. The efficiency of the proposed system is demonstrated through motor faults of electrical and mechanical origins on the induction motors. The results of the test indicate that the proposed system is promising for the real-time application.

Linear Parameter Varying Control of Induction Motors

DEFF Research Database (Denmark)

Trangbæk, Klaus

The subject of this thesis is the development of linear parameter varying (LPV) controllers and observers for control of induction motors. The induction motor is one of the most common machines in industrial applications. Being a highly nonlinear system, it poses challenging control problems...... for high performance applications. This thesis demonstrates how LPV control theory provides a systematic way to achieve good performance for these problems. The main contributions of this thesis are the application of the LPV control theory to induction motor control as well as various contributions...

Clinical and economic outcomes of rabbit antithymocyte globulin induction in adults who received kidney transplants from living unrelated donors and received cyclosporine-based immunosuppression.

Science.gov (United States)

Miller, James T; Collins, Curtis D; Stuckey, Linda J; Luan, Fu L; Englesbe, Michael J; Magee, John C; Park, Jeong M

2009-10-01

To evaluate the efficacy, safety, and costs of rabbit antithymocyte globulin (TMG) induction in patients who received kidney transplants from living unrelated donors. Retrospective cohort study. Large academic medical center. Eighty-seven patients who received kidney transplants from living unrelated donors: 40 of the recipients underwent transplantation between January 1, 2003, and December 31, 2004, and did not receive TMG induction (no induction group); 47 underwent transplantation between January 1, 2005, and June 30, 2006, and received TMG induction (induction group). All patients received cyclosporine-based immunosuppression. Biopsy-proven acute rejection, posttransplantation complications, and inpatient hospital costs for the first 12 months after transplantation were compared between groups using standard univariate statistical analyses. Induction significantly decreased the occurrence of biopsy-proven acute rejection versus no induction (2% vs 48%, pTMG treatment. Slightly elevated initial costs associated with TMG induction were offset by lower costs related to rejection treatment. Total inpatient costs for the 12 months after transplantation were comparable between the groups (no induction $66,038 vs induction $74,183, p>0.05). For the no induction versus induction groups, no significant differences in cytomegalovirus disease (5% vs 6%), malignancy (3% vs 2%), graft failures (5% vs 6%), mortality (5% vs 4%), and serum creatinine concentrations (mean +/- SD 1.4 +/- 0.3 vs 1.5 +/- 0.3 mg/dl) were observed at 12 months (p>0.05 for all comparisons). Five-day TMG induction effectively reduced the 1-year acute rejection rate without significantly increasing total inpatient costs or posttransplantation complications among recipients of kidney transplants from living unrelated donors.

Induction interview form in EDH

CERN Multimedia

Information technology Department, AIS (Administrative Information Services) Group,

2007-01-01

As part of the efforts to rationalise administrative procedures, the IT and HR Departments have developed a new EDH form for induction interviews, which can be accessed using the link below. In accordance with Administrative Circular No. 2 ('Recruitment, Appointment and possible developments regarding the contractual position of Staff Members', Rev. 3), the work and training objectives to be achieved during the probation period shall be specified in writing to all new staff members during an induction interview. The interview shall take place between the new staff member and his supervisor within six weeks of him taking up his duties at the latest. https://edh.cern.ch/Document/MAPS/Induction (or from the EDH desktop, by clicking on 'Other Tasks' and going to the 'HR & Training' heading) Please note that this form is to be used exclusively for new staff members. A separate EDH form will be developed for fellows. Information technology Department, AIS (Administrative Information Services) Group Human...

Induction interview form in EDH

CERN Document Server

Information technology Department, AIS (Administrative Information Services) Group

2007-01-01

As part of the efforts to rationalise administrative procedures, the IT and HR Departments have developed a new EDH form for induction interviews, which can be accessed using the link below. In accordance with Administrative Circular No. 2 ('Recruitment, Appointment and possible developments regarding the contractual position of Staff Members', Rev. 3), the work and training objectives to be achieved during the probation period shall be specified in writing to all new staff members during an induction interview. The interview shall take place between the new staff member and his supervisor within six weeks of his taking up his duties at the latest. https://edh.cern.ch/Document/MAPS/Induction1) (or from the EDH desktop, by clicking on 'Other Tasks' and going to the 'HR & Training' heading) Please note that this form is to be used exclusively for new staff members. A separate EDH form will be developed for fellows.Information technology Department, AIS (Administrative Information Services) Group Human Re...

Reducing Harmonic Instability and Resonance Problems in PMSG Based Wind Farms

DEFF Research Database (Denmark)

Ebrahimzadeh, Esmaeil; Blaabjerg, Frede; Wang, Xiongfei

2018-01-01

Unlike conventional power systems where harmonic resonances are coming from passive inductive and capacitive elements, large-scale power electronic systems like wind farms present a more complex system, where the fast dynamics of the power electronic converters may present an inductive or capacit......Unlike conventional power systems where harmonic resonances are coming from passive inductive and capacitive elements, large-scale power electronic systems like wind farms present a more complex system, where the fast dynamics of the power electronic converters may present an inductive...... or capacitive behavior. Therefore, the interactions between the fast controllers of the power converters and the passive elements may lead to harmonic instability and new resonances at various frequencies. This paper presents an optimum design technique for the Wind Turbine (WT) inner controllers in a PMSG...... based wind farm in order to reduce the number of resonances and to mitigate harmonic instability. In the approach, a PMSG based wind farm is modeled as a Multi-Input Multi-Output (MIMO) dynamic system by modeling the high bandwidth control loops of the power converters. Resonance frequencies...

Stability improvement of induction generator-based wind turbine systems

DEFF Research Database (Denmark)

Chen, Zhe; Hu, Y.; Blaabjerg, Frede

2007-01-01

The stability improvement of induction-generator-based wind turbine systems under power system fault conditions has been studied. Two types of generators are considered, namely rotor short-circuited induction generators and dynamic slip-controlled wound rotor induction generators. The factors...... affecting the stability are analysed. The characteristics of the induction-generator-based wind turbines are described, and possible methods of improving stability of the wind generators are discussed. The system modelling is presented, and then the discussed methods of improving stability are investigated...

An improved model of induction motors for diagnosis purposes - Slot skewing effect and air-gap eccentricity faults

Energy Technology Data Exchange (ETDEWEB)

Ghoggal, A.; Zouzou, S.E.; Sahraoui, M. [Laboratoire de genie electrique de Biskra, Departement d' electrotechnique, Universite Mohamed Khider, BP 145, Biskra (Algeria); Razik, H. [Groupe de Recherche en Electrotechnique et Electronique de Nancy, Universite Henri Poincare, Faculte des Sciences et Techniques, BP 239, F-54506 Vandoeuvre-les-Nancy (France); Khezzar, A. [Laboratoire d' Electrotechnique de Constantine, Universite Mentouri, Constantine (Algeria)

2009-05-15

This paper describes an improved method for the modeling of axial and radial eccentricities in induction motors (IM). The model is based on an extension of the modified winding function approach (MWFA) which allows for all harmonics of the magnetomotive force (MMF) to be taken into account. It is shown that a plane view of IM gets easily the motor inductances and reduces considerably the calculation process. The described technique includes accurately the slot skewing effect and leads to pure analytical expressions of the inductances in case of radial eccentricity. In order to model the static, dynamic or mixed axial eccentricity, three suitable alternatives are explained. Unlike the previous proposals, the discussed alternatives take into account all the harmonics of the inverse of air-gap function without any development in Fourier series. Simulation results as well as experimental verifications prove the usefulness and the effectiveness of the proposed model. (author)

An improved model of induction motors for diagnosis purposes - Slot skewing effect and air-gap eccentricity faults

International Nuclear Information System (INIS)

Ghoggal, A.; Zouzou, S.E.; Razik, H.; Sahraoui, M.; Khezzar, A.

2009-01-01

This paper describes an improved method for the modeling of axial and radial eccentricities in induction motors (IM). The model is based on an extension of the modified winding function approach (MWFA) which allows for all harmonics of the magnetomotive force (MMF) to be taken into account. It is shown that a plane view of IM gets easily the motor inductances and reduces considerably the calculation process. The described technique includes accurately the slot skewing effect and leads to pure analytical expressions of the inductances in case of radial eccentricity. In order to model the static, dynamic or mixed axial eccentricity, three suitable alternatives are explained. Unlike the previous proposals, the discussed alternatives take into account all the harmonics of the inverse of air-gap function without any development in Fourier series. Simulation results as well as experimental verifications prove the usefulness and the effectiveness of the proposed model.

Computer simulation of a 3-phase induction motor

International Nuclear Information System (INIS)

Memon, N.A.; Unsworth, P.J.

2004-01-01

Computer Simulation of a 3-phase squirrel-cage induction motor is presented in Microsoft QBASIC for understanding trends and various operational modes of an induction motor. Thyristor fed, phase controlled induction motor (three-wire) model has been simulated. In which voltage is applied to the motor stator winding through back-to-back connected thyristors as controlled switches in series with the stator. The simulated induction motor system opens up towards a wide range of investigation/analysis options for research and development work in the field. Key features of the simulation performed are highlighted for development of better understanding of the work done. Complete study of an Induction Motor, starting modes in terms the voltage/current, torque/speed characteristics and their graphical representation produced is presented. Ideal agreement of the simulation results with the notional outcome encourages users to go ahead for various hardware development projects based on the study through the simulation. (author)

Induction of labor in a contemporary obstetric cohort.

Science.gov (United States)

Laughon, S Katherine; Zhang, Jun; Grewal, Jagteshwar; Sundaram, Rajeshwari; Beaver, Julie; Reddy, Uma M

2012-06-01

We sought to describe details of labor induction, including precursors and methods, and associated vaginal delivery rates. This was a retrospective cohort study of 208,695 electronic medical records from 19 hospitals across the United States, 2002 through 2008. Induction occurred in 42.9% of nulliparas and 31.8% of multiparas and elective or no recorded indication for induction at term occurred in 35.5% and 44.1%, respectively. Elective induction at term in multiparas was highly successful (vaginal delivery 97%) compared to nulliparas (76.2%). For all precursors, cesarean delivery was more common in nulliparas in the latent compared to active phase of labor. Regardless of method, vaginal delivery rates were higher with a ripe vs unripe cervix, particularly for multiparas (86.6-100%). Induction of labor was a common obstetric intervention. Selecting appropriate candidates and waiting longer for labor to progress into the active phase would make an impact on decreasing the national cesarean delivery rate. Published by Mosby, Inc.

Induced cytochrome P450 1A activity in cichlid fishes from Guandu River and Jacarepagua Lake, Rio de Janeiro, Brazil

International Nuclear Information System (INIS)

Parente, Thiago E.M.; Oliveira, Ana C.A.X. de; Paumgartten, Francisco J.R.

2008-01-01

The induction of cytochrome P4501A-mediated activity (e.g. ethoxyresorufin-O-deethylation, EROD) has been used as a biomarker for monitoring fish exposure to AhR-receptor ligands such as polycyclic aromatic hydrocarbons (PAH), polychlorinated biphenyls (PCB) and polychlorinated dibenzo-dioxins/furans (PCDD/Fs). In this study we found that hepatic EROD is induced in fish ('Nile tilapia', Oreochromis niloticus and 'acara', Geophagus brasiliensis) from the Guandu River (7-17-fold) and Jacarepagua Lake (7-fold), Rio de Janeiro, Brazil. Since both cichlid fish are consumed by the local population and the Guandu River is the main source of the drinking water supply for the greater Rio de Janeiro metropolitan area, pollution by cytochrome P4501A-inducing chemicals is a cause for concern and should be further investigated in sediments, water and biota. We additionally showed that EROD activity in the fish liver post-mitochondrial supernatant-simpler, cheaper and less time consuming to prepare than the microsomal fraction-is sufficiently sensitive for monitoring purposes. - Increased EROD activity in the liver of cichlid fishes indicated that Guandu River, the source of drinking water supply for Rio de Janeiro is polluted by CYP1A-inducing chemicals

Surface Induction Hardening of Axi-Symmetric Bodies

Czech Academy of Sciences Publication Activity Database

Barglik, J.; Doležel, Ivo; Škopek, M.; Ulrych, B.

2001-01-01

Roč. 1, č. 1 (2001), s. 11-16 ISSN 1335-8243 R&D Projects: GA ČR GA102/01/0184 Grant - others:-(PL) 7T08603716 Keywords : induction heating * induction hardening * numerical solution Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

Numerical simulation of induction heating thick-walled tubes

Directory of Open Access Journals (Sweden)

Lenhard Richard

2018-01-01

Full Text Available In the paper is shown the connection of two toolboxes in an Ansys Workbench solution for induction heating. In Ansys Workbench, Maxwell electromagnetism programs and Fluent have been linked. In Maxwell, a simulation of electromagnetic induction was performed, where data on the magnetic field distribution in the heated material was obtained and then transformed into the Fluent program in which the induction heating simulation was performed.

Analysis of SOS-Induced Spontaneous Prophage Induction in Corynebacterium glutamicum at the Single-Cell Level

Science.gov (United States)

Nanda, Arun M.; Heyer, Antonia; Krämer, Christina; Grünberger, Alexander; Kohlheyer, Dietrich

2014-01-01

The genome of the Gram-positive soil bacterium Corynebacterium glutamicum ATCC 13032 contains three integrated prophage elements (CGP1 to -3). Recently, it was shown that the large lysogenic prophage CGP3 (∼187 kbp) is excised spontaneously in a small number of cells. In this study, we provide evidence that a spontaneously induced SOS response is partly responsible for the observed spontaneous CGP3 induction. Whereas previous studies focused mainly on the induction of prophages at the population level, we analyzed the spontaneous CGP3 induction at the single-cell level using promoters of phage genes (Pint2 and Plysin) fused to reporter genes encoding fluorescent proteins. Flow-cytometric analysis revealed a spontaneous CGP3 activity in about 0.01 to 0.08% of the cells grown in standard minimal medium, which displayed a significantly reduced viability. A PrecA-eyfp promoter fusion revealed that a small fraction of C. glutamicum cells (∼0.2%) exhibited a spontaneous induction of the SOS response. Correlation of PrecA to the activity of downstream SOS genes (PdivS and PrecN) confirmed a bona fide induction of this stress response rather than stochastic gene expression. Interestingly, the reporter output of PrecA and CGP3 promoter fusions displayed a positive correlation at the single-cell level (ρ = 0.44 to 0.77). Furthermore, analysis of the PrecA-eyfp/Pint2-e2-crimson strain during growth revealed the highest percentage of spontaneous PrecA and Pint2 activity in the early exponential phase, when fast replication occurs. Based on these studies, we postulate that spontaneously occurring DNA damage induces the SOS response, which in turn triggers the induction of lysogenic prophages. PMID:24163339

Harmonic modeling of induction motors

Energy Technology Data Exchange (ETDEWEB)

Pedra, J.; Sainz, L.; Corcoles, F. [Department of Electrical Engineering, ETSEIB-UPC, Av. Diagonal 647, 08028 Barcelona (Spain)

2006-07-15

The paper proposes an induction motor model for the study of harmonic load flow in balanced and unbalanced conditions. The parameters of this model are obtained from motor manufacturer data and the positive- and negative-sequence equivalent circuits of the single- and double-cage models. An approximate harmonic model based on motor manufacturer data only is also proposed. In addition, the paper includes manufacturer data and the calculated parameters of 36 induction motors of different rated powers. This database is used to analyze the proposed models. (author)

Induction linacs and pulsed power

International Nuclear Information System (INIS)

Caporaso, G.J.

1995-01-01

Progress in electronic power conversion technology is making possible a new class of induction linacs that can operate at extremely high repetition rates. Advances in insulator technology, pulse forming line design and switching may also lead to a new type of high current accelerator with accelerating gradients at least an order of magnitude greater than those attainable today. The evolution of the induction accelerator pulsed power system will be discussed along with some details of these emerging technologies which are at the frontiers of accelerator technology

Timing of induction of labor.

Science.gov (United States)

Bacak, Stephen J; Olson-Chen, Courtney; Pressman, Eva

2015-10-01

Determining the optimal timing for induction of labor is critical in minimizing the risks to maternal and fetal health. While data are available to guide us in some clinical situations, such as hypertension and diabetes, many gaps in knowledge still exist in others, including cholestasis of pregnancy, fetal anomalies, and placental abruption. This review of the currently available literature assesses the risks and benefits of preterm and early term induction in a wide variety of maternal and fetal conditions. Copyright © 2015 Elsevier Inc. All rights reserved.

Sparus aurata L. liver EROD and GST activities, plasma cortisol, lactate, glucose and erythrocytic nuclear anomalies following short-term exposure either to 17{beta}-estradiol (E{sub 2}) or E{sub 2} combined with 4-nonylphenol

Energy Technology Data Exchange (ETDEWEB)

Teles, M.; Pacheco, M.; Santos, M.A

2005-01-05

Immature Sparus aurata L. (gilthead seabream) were exposed to 17{beta}-estradiol (E{sub 2}) 4000 ng/l and to the same E{sub 2} concentration mixed with 50,000 ng/l 4-nonylphenol (E{sub 2}+NP) during 4, 8, 12 and 16 h. E{sub 2} availability and E{sub 2} plasma level variations were assessed. Liver biotransformation capacity was measured as ethoxyresorufin-O-deethylase (EROD) and glutathione-S-transferase (GST) activities. Plasma cortisol, lactate and glucose were also determined. Genotoxicity was assessed through erythrocytic nuclear anomalies (ENA) frequency. Liver EROD activity significantly decreased during the whole experiment for both treatments, with the exception of 16 h exposure to E{sub 2}. Liver GST activity was significantly increased after 8 and 12 h of exposure either to E{sub 2} or E{sub 2}+NP. An endocrine disruption expressed as plasma cortisol decrease was observed after 16 h exposure under both tested conditions, concomitantly with a plasma lactate increase. No genotoxic responses, measured as ENA frequency, were detected. Analyzing the E{sub 2} water concentration in aquaria without fish it was demonstrated an intense and fast E{sub 2} loss, considerably reducing its availability to fish. In the presence of fish, E{sub 2} water levels were drastically reduced after 4 h exposure, being this reduction more pronounced in E{sub 2} aquarium when compared to E{sub 2}+NP aquarium. In addition, it was demonstrated a rapid E{sub 2} uptake from the water since the highest E{sub 2} plasma concentrations were observed after 4 h exposure, followed by a continuous decrease, which became more pronounced between 8 and 12 h of exposure. Furthermore, during the first 8 h exposure to E{sub 2} and E{sub 2}+NP, seabream plasma E{sub 2} concentrations were higher than the initial water exposure concentration. Comparing the E{sub 2} plasma levels in both seabream-exposed groups, it was clear that its concentration is always higher in E{sub 2}+NP-treated fish. Despite

FEM Optimal Design of Energy Efficient Induction Machines

Directory of Open Access Journals (Sweden)

TUDORACHE, T.

2009-06-01

Full Text Available This paper deals with a comparative numerical analysis of performances of several design solutions of induction machines with improved energy efficiency. Starting from a typical cast aluminum cage induction machine this study highlights the benefit of replacing the classical cast aluminum cage with a cast copper cage in the manufacture of future generation of high efficiency induction machines used as motors or generators. Then the advantage of replacement of standard electrical steel with higher grade steel with smaller losses is pointed out. The numerical analysis carried out in the paper is based on 2D plane-parallel finite element approach of the induction machine, the numerical results being discussed and compared with experimental measurements.

Analyzing high school students’ reasoning about electromagnetic induction

Directory of Open Access Journals (Sweden)

Katarina Jelicic

2017-02-01

Full Text Available Electromagnetic induction is an important, yet complex, physics topic that is a part of Croatian high school curriculum. Nine Croatian high school students of different abilities in physics were interviewed using six demonstration experiments from electromagnetism (three of them concerned the topic of electromagnetic induction. Students were asked to observe, describe, and explain the experiments. The analysis of students’ explanations indicated the existence of many conceptual and reasoning difficulties with the basic concepts of electromagnetism, and especially with recognizing and explaining the phenomenon of electromagnetic induction. Three student mental models of electromagnetic induction, formed during the interviews, which reoccurred among students, are described and analyzed within the knowledge-in-pieces framework.

Modelling imperfect adherence to HIV induction therapy

Directory of Open Access Journals (Sweden)

Smith? Robert J

2010-01-01

Full Text Available Abstract Background Induction-maintenance therapy is a treatment regime where patients are prescribed an intense course of treatment for a short period of time (the induction phase, followed by a simplified long-term regimen (maintenance. Since induction therapy has a significantly higher chance of pill fatigue than maintenance therapy, patients might take drug holidays during this period. Without guidance, patients who choose to stop therapy will each be making individual decisions, with no scientific basis. Methods We use mathematical modelling to investigate the effect of imperfect adherence during the inductive phase. We address the following research questions: 1. Can we theoretically determine the maximal length of a possible drug holiday and the minimal number of doses that must subsequently be taken while still avoiding resistance? 2. How many drug holidays can be taken during the induction phase? Results For a 180 day therapeutic program, a patient can take several drug holidays, but then has to follow each drug holiday with a strict, but fairly straightforward, drug-taking regimen. Since the results are dependent upon the drug regimen, we calculated the length and number of drug holidays for all fifteen protease-sparing triple-drug cocktails that have been approved by the US Food and Drug Administration. Conclusions Induction therapy with partial adherence is tolerable, but the outcome depends on the drug cocktail. Our theoretical predictions are in line with recent results from pilot studies of short-cycle treatment interruption strategies and may be useful in guiding the design of future clinical trials.

Inductive energy storage commutator

International Nuclear Information System (INIS)

Gavrilov, I.M.

1987-01-01

An inductive energy storage commutator is described. The value of commutated current is up to 800 A, the voltage amplitude in the load is up to 50 kV, the working frequency is equal to 1-50 Hz, the commutated power is up to 40 MW. The commutating device comprises of the first stage commutator having two in-series connected modules of the BTSV - 800/235 high-voltage thyristor unit, the second stage commutator containing three GMI-43A parallel connected powerful pulsed triodes, a commutating capacitor, an induction coil, two supplementary high-voltage thyristor keys (20 in-series connected thyristors T2-300 (13 class)), load, control pulse shapers, thyristor keys, power supply

Cognitive Trait Modelling: The Case of Inductive Reasoning Ability

Science.gov (United States)

Kinshuk, Taiyu Lin; McNab, Paul

2006-01-01

Researchers have regarded inductive reasoning as one of the seven primary mental abilities that account for human intelligent behaviours. Researchers have also shown that inductive reasoning ability is one of the best predictors for academic performance. Modelling of inductive reasoning is therefore an important issue for providing adaptivity in…

Performance of a Folded-Strip Toroidally Wound Induction Machine

DEFF Research Database (Denmark)

Jensen, Bogi Bech; Jack, Alan G.; Atkinson, Glynn J.

2011-01-01

This paper presents the measured experimental results from a four-pole toroidally wound induction machine, where the stator is constructed as a pre-wound foldable strip. It shows that if the machine is axially restricted in length, the toroidally wound induction machine can have substantially...... shorter stator end-windings than conventionally wound induction machines, and hence that a toroidally wound induction machine can have lower losses and a higher efficiency. The paper also presents the employed construction method, which emphasizes manufacturability, and highlights the advantages...

Nitric oxide is not a negative regulator of metamorphic induction in the abalone Haliotis asinina

Directory of Open Access Journals (Sweden)

Nobuo eUeda

2014-07-01

Full Text Available Nitric oxide (NO is a second messenger molecule synthesized by the enzyme nitric oxide synthase (NOS that requires the molecular chaperone heat shock protein 90 (HSP90 for normal enzymatic activity. Past studies have revealed that both NO and HSP90 act as negative regulators (repressors of metamorphosis in a diverse range of marine invertebrates, including several molluscan species. Here, we test the role of NO in the metamorphic induction of a vetigastropod mollusc, the tropical abalone Haliotis asinina. Specifically, we 1 test the effects of NO-manipulating pharmacological agents, 2 measure the temporal expression of NOS and HSP90 genes through metamorphosis, and 3 assess the spatial expression of NOS and HSP90 in larvae. We find that inhibition of NOS reduces rates of metamorphosis, indicating that NO facilitates, rather than represses, induction of metamorphosis in H. asinina. The marked increase in NOS expression in putative sensory cells localized to the anterior foot of competent larvae is consistent with NO as an inductive molecule for metamorphosis. In contrast to NOS, HSP90 transcript abundance decreases at competence and there is no evidence of NOS and HSP90 transcript co-localization. This study provides the first evidence of NO as an inductive facilitator of molluscan metamorphosis. Our experimental data suggest that NO modulates signals derived from live inductive substrates via the larval foot to regulate metamorphosis. Inter-specific comparisons of spatial NOS expression in molluscs suggest that the localized pattern of NOS or its protein product is related to the regulatory action of NO in metamorphosis.

Acute exercise attenuates negative affect following repeated sad mood inductions in persons who have recovered from depression.

Science.gov (United States)

Mata, Jutta; Hogan, Candice L; Joormann, Jutta; Waugh, Christian E; Gotlib, Ian H

2013-02-01

Identifying factors that may protect individuals from developing Major Depressive Disorder (MDD) in the face of stress is critical. In the current study we experimentally tested whether such a potentially protective factor, engaging in acute exercise, reduces the adverse effects of repeated sad mood inductions in individuals who have recovered from depression. We hypothesized that recovered depressed participants who engage in acute exercise report a smaller increase in negative affect (NA) and a smaller decrease in positive affect (PA) when exposed to a repeated sad mood induction (i.e., habituation), whereas participants who do not exercise show sensitization (i.e., increased NA and decreased PA in response to a repeated adverse stimulus). Forty-one women recovered from MDD and 40 healthy control women were randomly assigned to either exercise for 15 minutes or quiet rest. Afterward, participants were exposed to two sad mood inductions and reported their levels of affect throughout the study. Recovered depressed participants who had not exercised exhibited higher NA after the second sad mood induction, a finding consistent with sensitization. In contrast, both recovered depressed participants who had engaged in acute exercise and healthy control participants showed no increase in NA in response to the repeated sad mood induction. Participants who exercised reported higher PA after the exercise bout; however, our hypothesis concerning reported PA trajectories following the sad mood inductions was not supported. Results suggest that exercise can serve as a protective factor in the face of exposure to repeated emotional stressors, particularly concerning NA in individuals who have recovered from depression. 2013 APA, all rights reserved

Reconstruction of Eroded and Visually Complicated Archaeological Geometric Patterns: Minaret Choli, Iraq

Directory of Open Access Journals (Sweden)

Rima Al Ajlouni

2011-12-01

Full Text Available Visually complicated patterns can be found in many cultural heritages of the world. Islamic geometric patterns present us with one example of such visually complicated archaeological ornaments. As long-lived artifacts, these patterns have gone through many phases of construction, damage, and repair and are constantly subject to erosion and vandalism. The task of reconstructing these visually complicated ornaments faces many practical challenges. The main challenge is posed by the fact that archaeological reality often deals with ornaments that are broken, incomplete or hidden. Recognizing faint traces of eroded or missing parts proved to be an extremely difficult task. This is also combined with the need for specialized knowledge about the mathematical rules of patterns’ structure, in order to regenerate the missing data. This paper presents a methodology for reconstructing deteriorated Islamic geometric patterns; to predict the features that are not observed and output a complete reconstructed two-dimension accurate measurable model. The simulation process depends primarily on finding the parameters necessary to predict information, at other locations, based on the relationships embedded in the existing data and in the prior -knowledge of these relations. The aim is to build up from the fragmented data and from the historic and general knowledge, a model of the reconstructed object. The proposed methodology was proven to be successful in capturing the accurate structural geometry of many of the deteriorated ornaments on the Minaret Choli, Iraq. However, in the case of extremely deteriorated samples, the proposed methodology failed to recognize the correct geometry. The conceptual framework proposed by this paper can serve as a platform for developing professional tools for fast and efficient results.

Inductance-dependent characteristics of HTS dc-SQUID amplifiers

International Nuclear Information System (INIS)

Mitchell, E.E.; Tilbrook, D.L.; Foley, C.P.; MacFarlane, J.

2002-01-01

Full text: We have experimentally determined the transfer function V Φ and noise S Φ of several high temperature superconducting (HTS) dc SQUIDs of increasing loop size, while they were operated (without input flux transformer) in a small-signal-amplifier (open-loop) mode. A primary aim of our investigation was to provide reliable inductance data to aid our design of subsequent magnetometer devices. Flux was induced by means of current injection via a well-defined stripline directly into the SQUID loop. The loop size was systematically incremented in a range of otherwise similar SQUIDs. For each SQUID, the ratio between the induced flux and the injection current (which we define as the coupling inductance of the device, L c ) was measured as a function of the injection path length and the SQUID loop dimensions. Both L c and the derived SQUID self-inductance, L sq , were then compared with theoretical values, and contributions due to kinetic inductance and junction inductance were estimated. Correlations between the inductance data and our measured values of transfer function V Φ and noise S Φ were compared with previous results. Guidelines for optimisation of gradiometer SQUIDs were established, and in particular, the importance of achieving a large value transfer function together with a relatively small inductance was demonstrated. The strong influence of an enhanced transfer function was further emphasised when an order-of-magnitude reduction in noise was achieved by subjecting one of our SQUIDs to an in-house 'ion-beam trimming' process

Induction of Shiga Toxin-Encoding Prophage by Abiotic Environmental Stress in Food.

Science.gov (United States)

Fang, Yuan; Mercer, Ryan G; McMullen, Lynn M; Gänzle, Michael G

2017-10-01

The prophage-encoded Shiga toxin is a major virulence factor in Stx-producing Escherichia coli (STEC). Toxin production and phage production are linked and occur after induction of the RecA-dependent SOS response. However, food-related stress and Stx-prophage induction have not been studied at the single-cell level. This study investigated the effects of abiotic environmental stress on stx expression by single-cell quantification of gene expression in STEC O104:H4 Δ stx2 :: gfp :: amp r In addition, the effect of stress on production of phage particles was determined. The lethality of stressors, including heat, HCl, lactic acid, hydrogen peroxide, and high hydrostatic pressure, was selected to reduce cell counts by 1 to 2 log CFU/ml. The integrity of the bacterial membrane after exposure to stress was measured by propidium iodide (PI). The fluorescent signals of green fluorescent protein (GFP) and PI were quantified by flow cytometry. The mechanism of prophage induction by stress was evaluated by relative gene expression of recA and cell morphology. Acid (pH stress were additionally assessed. H 2 O 2 and mitomycin C induced expression of the prophage and activated a SOS response. In contrast, HCl and lactic acid induced the Stx-prophage but not the SOS response. The lifestyle of STEC exposes the organism to intestinal and extraintestinal environments that impose oxidative and acid stress. A more thorough understanding of the influence of food processing-related stressors on Stx-prophage expression thus facilitates control of STEC in food systems by minimizing prophage induction during food production and storage. Copyright © 2017 American Society for Microbiology.

Development of a low-cost inductively coupled argon plasma

International Nuclear Information System (INIS)

Ripson, P.A.M.

1983-01-01

The aim of this investigation is to drastically reduce running costs of an inductively coupled plasma. This is done by reducing the argon consumption from 20 l/min to about 1 l/min. First, a sample introduction system operating on 0.1 l/min of carrier argon is described. This system ensures a high ratio of plasma argon and carrier argon even at the low total argon consumptions intended. Next, the developed low consumption plasma is presented. In the proposed design, air is blown perpendicularly against the outside of the torch. A different coil has been developed to make air-cooling efficient. Preliminary data on coupling efficiency for the air-cooled plasma are presented. A similarly low argon consumption has been achieved with water as an external coolant medium. It is concluded that a cheaper alternative to the current ICP has become available. (Auth.)

Armature design for coaxial induction launchers

International Nuclear Information System (INIS)

Andrews, J.A.; Devine, J.R.

1991-01-01

This paper reports on the armature design for a coaxial induction launcher that is influenced by a large set of highly coupled parameters. The simplifying assumptions often employed in coaxial accelerator analysis, such as a uniform or sinusoidal axial distribution of the azimuthal armature current, are unrealistic in induction launchers with monolithic single-turn armatures. In order to better understand the true dynamic behavior of coaxial accelerators, the Center for Electromechanics at The University of Texas at Austin (CEM-UT) has developed series of computer codes based on the current filament method. By utilizing these performance codes in conjunction with electromagnetic (EM) and mechanical finite element programs, it is now possible to design high performance induction launchers with armatures that can withstand the considerable mechanical and thermal loads inherent in a coaxial accelerator launch

A logic for inductive probabilistic reasoning

DEFF Research Database (Denmark)

Jaeger, Manfred

2005-01-01

Inductive probabilistic reasoning is understood as the application of inference patterns that use statistical background information to assign (subjective) probabilities to single events. The simplest such inference pattern is direct inference: from '70% of As are Bs" and "a is an A" infer...... that a is a B with probability 0.7. Direct inference is generalized by Jeffrey's rule and the principle of cross-entropy minimization. To adequately formalize inductive probabilistic reasoning is an interesting topic for artificial intelligence, as an autonomous system acting in a complex environment may have...... to base its actions on a probabilistic model of its environment, and the probabilities needed to form this model can often be obtained by combining statistical background information with particular observations made, i.e., by inductive probabilistic reasoning. In this paper a formal framework...

Oral tolerance induction for human food allergy.

Science.gov (United States)

Noh, Geunwoong; Lee, Jae Ho

2012-04-01

Food allergies are classified as IgE-mediated and non-IgE mediated type. The number of successful reports of immunotherapy, namely tolerance induction for food allergy (TIFA) are increasing, bringing hope for meaningful positive and radical treatment of food allergy. Therapeutic characteristics of the clinical course in TIFA for NFA are different from TIFA for IFA. Cytokines including IL-10, TGF-β and IFN-γ and regulatory cells such as Treg and Breg, are involved in immune tolerance. IFN-γ has been used for tolerance induction of food allergy as an immunomodulatory biologics. A definitive distinction between IgE-mediated and non-IgE-mediated food allergies is absolutely essential for diagnostic and therapeutic purposes. Original SOTI using IFN-γ is more effective then conventional SOTI without IFN-γ. Especially, IFN-γ is absolutely necessary for the tolerance induction of NFA. This review highlights and updates the advances in the conceptual immunological background and the clinical characteristics of oral tolerance induction for food allergy.

Development trends of combined inductance-capacitance electromechanical energy converters

Directory of Open Access Journals (Sweden)

Karayan Hamlet

2018-01-01

Full Text Available In the article the modern state of completely new direction of electromechanical science such as combined inductive-capacitive electromechanics is considered. The wide spectra of its possible practical applications and prospects for further development are analyzed. A new approach for mathematical description of transients in dualcon jugate dynamic systems is proposed. On the basis of the algorithm differential equations for inductive-capacitive compatible electromechanical energy converters are derived. The generalized Lagrangian theory of combined inductively-capacitive electric machines was developed as a union of generalized Lagrangian models of inductive and capacitive electro-mechanical energy converters developed on the basis of the basic principles of binary-conjugate electrophysics. The author gives equations of electrodynamics and electromechanics of combined inductive-capacitive electric machines in case there are active electrotechnical materials of dual purpose (ferroelectromagnets in the structure of their excitation system. At the same time, the necessary Lagrangian for combined inductive-capacitive forces was built using new technologies of interaction between inductive and capacitive subsystems. The joint solution of these equations completely determines the dynamic behavior and energy characteristics of the generalized model of combined machines of any design and in any modes of interaction of their functional elements

Feature-Based versus Category-Based Induction with Uncertain Categories

Science.gov (United States)

Griffiths, Oren; Hayes, Brett K.; Newell, Ben R.

2012-01-01

Previous research has suggested that when feature inferences have to be made about an instance whose category membership is uncertain, feature-based inductive reasoning is used to the exclusion of category-based induction. These results contrast with the observation that people can and do use category-based induction when category membership is…

A Logic Programming Testbed for Inductive Thought and Specification.

Science.gov (United States)

Neff, Norman D.

This paper describes applications of logic programming technology to the teaching of the inductive method in computer science and mathematics. It discusses the nature of inductive thought and its place in those fields of inquiry, arguing that a complete logic programming system for supporting inductive inference is not only feasible but necessary.…

CALCULATION OF INDUCTANCE OF THE INTERIOR PERMANENT MAGNET SYNCHRONOUS MOTOR

Directory of Open Access Journals (Sweden)

Phyong Le Ngo

2017-01-01

Full Text Available Interior permanent magnet synchronous motor (IPMSM refers to salient-pole synchronous motors, characterized by inequality of inductances of longitudinal (d and transverse (q axes. Electromagnetic torque of IPMSM consists of two components: active torque and reactive torque; the latter depends on inductances of d and q axes. An analytical method to calculate own inductances and mutual inductances of a three-phase IPMSM is presented. Distributed windings of the stator are substituted by equivalent sine distributed windings. An interior permanent magnets rotor is substituted by an equivalent salient-pole rotor. Sections of a magnetic circuit comprising interior permanent magnets, air barriers and steel bridges are substituted by equivalent air-gap. The expressions of the magnetic induction created by current of the stator windings at each point of the air gap as well as of magnetic flux linkage of the stator windings have been obtained. The equations of the self-inductances of phases A, B, C, and of inductance of mutual induction are determined from magnetic flux linkage. The inductance of the d and q axes have been obtained as a result of transformation of the axes abc–dq. The results obtained with the use of the proposed analytical method and the finite element method are presented in the form of a graph; the calculations that have been obtained by these two methods were compared. 

Recirculating induction accelerator as a low-cost driver for heavy ion fusion

International Nuclear Information System (INIS)

Barnard, J.J.; Newton, M.A.; Reginato, L.L.; Sharp, W.M.; Shay, H.D.; Yu, S.S.

1991-09-01

As a fusion driver, a heavy ion accelerator offers the advantages of efficient target coupling, high reliability, and long stand-off focusing. While the projected cost of conventional heavy ion fusion (HIF) drivers based on multiple beam induction linacs are quite competitive with other inertial driver options, a driver solution which reduces the cost by a factor of two or more will make the case for HIF truly compelling. The recirculating induction accelerator has the potential of large cost reductions. For this reason, an intensive study of the recirculator concept was performed by a team from LLNL and LBL over the past year. We have constructed a concrete point design example of a 4 MJ driver with a projected efficiency of 35% and projected cost of less than 500 million dollars. A detailed report of our findings during this year of intensive studies has been recently completed. 3 refs., 2 figs., 2 tabs

Loss of Landau Damping for Inductive Impedance in a Double RF System

CERN Document Server

Argyropoulos, T; Burov, A

2013-01-01

In this paper the thresholds of the loss of Landau damping due to the presence of inductive impedance in a single and double harmonic RF systems are determined, both from calculations and particle simulations. A high harmonic RF system, operating in bunch lengthening mode is used in many accelerators with space charge or inductive impedance to reduce the peak line density or stabilize the beam. An analytical approach, based on emerging of the discrete Van Kampen modes, shows that improved stability in a double RF system can be achieved only below some critical value of longitudinal emittance. Above this threshold, a phase shift of more than 15 degrees between the two RF components is proven necessary to stabilize the bunch. These results, confirmed also by particle simulations, now are able to explain observations during the pp operation of the SPS. The thresholds in bunch shortening mode as well as in a single RF case are compared with this regime.

The Tower of Hanoi and Inductive Logic

Science.gov (United States)

Merrotsy, Peter

2015-01-01

In the "Australian Curriculum," the concept of mathematical induction is first met in the senior secondary subject Specialist Mathematics. This article details an example, the Tower of Hanoi problem, which provides an enactive introduction to the inductive process before moving to more abstract and cognitively demanding representations.…

Effect of kicker circuit inductance on the transmission-line discharging

International Nuclear Information System (INIS)

Feng Deren; Wang Xiangqi; Shang Lei; Pei Yuanji; Fan Kuanjun

2004-01-01

Circuit inductance exists at discharging circuit of transmission-line, it includes the inductance at the main switch of thyratron when conducts, the linking inductance between the linking cables, the matching resistance inductance and the load inductance. When a long pulse is generated by transmission-line, the circuit inductance can be omitted. However, when the pulse is short (such as shorter than 200 ns), especially when ferromagnetic core kicker acts as the load, the effect is obvious. The short pulse current is needed in order to generate long time interval synchronous radiation light pulses by using online assembly of pulse convex orbit and DC convex orbit. This paper analyses the effect and presents several experimental results. It also supposes two practical cases to decrease the rise time of the pulse

Induction chemotherapy in acute myeloid leukaemia: origins and emerging directions.

Science.gov (United States)

Upadhyay, Vivek A; Fathi, Amir T

2018-03-01

This review summarizes the hallmark developments in induction chemotherapy for acute myeloid leukaemia and further describes future directions in its evolution. We describe the origin of induction chemotherapy. We also describe notable modifications and adjustments to 7+3 induction chemotherapy since its development. Finally, we describe new efforts to modify and add new agents to induction therapy, including '7+3 Plus' combinations. Induction chemotherapy remains the standard of care for the majority of patients with acute myeloid leukaemia. However, its success is limited in a subset of patients by toxicity, failure to achieve remission and potential for subsequent relapse. Novel agents such as mutant fms like tyrosine kinase 3 inhibitors, mutant isocitrate dehydrogenase inhibitors, CD33-antibody drug conjugates and liposomal formulations have demonstrated significant potential as modifications to traditional induction chemotherapy.

A theory evaluation of an induction programme

Directory of Open Access Journals (Sweden)

Kenrick Hendricks

2012-07-01

Full Text Available Orientation: An induction programme is commonly used to help new employees understand their job within the organisation. Research purpose: The main aim of this study was to examine whether or not the programme theory of an induction programme was plausible and would lead to the intended outcomes as described by the programme manager. Motivation for the study: Induction training is one of the most common training programmes in an organisation. However, there is little research to evaluate whether or not the activities of an induction programme will lead to the intended outcomes of such a programme. Research design, approach and method: This theory evaluation used a descriptive design. One hundred and thirteen employees of a media company completed a ten-item, five-point Likert scale which measured their perceptions of the programme’s outcome, identification with the organisation and intentions to stay with the organisation. Main findings: From this theory evaluation it was apparent that an induction programme based on an implausible programme theory could be problematic. An implausible programme theory affects the design of the programme activities and unsuitable activities may not deliver the desired outcomes. Practical/managerial implications: The intention of the evaluation is to guide human resource managers through a process of replacing an implausible programme theory with one that is plausible, and which ensures better alignment of programme activities and outcomes. Contribution/value-add: The evaluators showed how a plausible programme theory could improve programme design. This redesigned induction programme may lead to benefits, such as staff retention and company identification, rather than the vague assumption that it has been conforming to a legal obligation.

Sliding Mode Control of Induction Motor Phase Currents

DEFF Research Database (Denmark)

Hansen, R.B.; Hattel, T.; Bork, J

1995-01-01

Sliding mode control of induction motor phase currents are investigated through development of two control concepts.......Sliding mode control of induction motor phase currents are investigated through development of two control concepts....

Risk Factors for Cesarean Delivery following Labor Induction in Multiparous Women

Directory of Open Access Journals (Sweden)

Corine J. Verhoeven

2013-01-01

Full Text Available Objective. To identify potential risk factors for cesarean delivery following labor induction in multiparous women at term. Methods. We conducted a retrospective case-control study. Cases were parous women in whom the induction of labor had resulted in a cesarean delivery. For each case, we used the data of two successful inductions as controls. Successful induction was defined as a vaginal delivery after the induction of labor. The study was limited to term singleton pregnancies with a child in cephalic position. Results. Between 1995 and 2010, labor was induced in 2548 parous women, of whom 80 had a cesarean delivery (3%. These 80 cases were compared to the data of 160 parous women with a successful induction of labor. In the multivariate analysis history of preterm delivery (odds ratio (OR 5.3 (95% CI 1.1 to 25, maternal height (OR 0.87 (95% CI 0.80 to 0.95 and dilatation at the start of induction (OR 0.43 (95% CI 0.19 to 0.98 were associated with failed induction. Conclusion. In multiparous women, the risk of cesarean delivery following labor induction increases with previous preterm delivery, short maternal height, and limited dilatation at the start of induction.

Induction of cytochrome P450-associated monooxygenases in northern leopard frogs, Rana pipiens, by 3,3',4,4',5-pentachlorobiphenyl

Science.gov (United States)

Huang, Y.-W.; Melancon, M.J.; Jung, R.E.; Karasov, W.H.

1998-01-01

Northern leopard frogs (Rana pipiens) were injected intraperitoneally either with a solution of polychlorinated biphenyl (PCB) 126 in corn oil at a concentration of 0.2, 0.7, 2.3 and 7.8 mg/kg body weight or with corn oil alone. Appropriate assay conditions with hepatic microsomes were determined for four cytochrome P450-associated monooxygenases: ethoxyresorufin-O-dealkylase (EROD), methoxy-ROD (MROD), benzyloxy-ROD (BROD) and pentoxy-ROD (PROD). One week after PCB administration, the specific activities of EROD, MROD, BROD and PROD were not elevated at doses ? 0.7 mg/kg (p > 0.05), but were significantly increased at doses ? 2.3 mg/kg compared to the control groups (p leopard frogs.

Enhancement of callus induction and regeneration efficiency from ...

African Journals Online (AJOL)

Administrator

2011-09-05

Sep 5, 2011 ... efficiency from embryo cultures of Datura stramonium ... cycle (callus induction and plant regeneration) for Datura stramonium by adjusting carbon sources and ... induction and development in various species, it is not.

Spine formation pattern of adult-born neurons is differentially modulated by the induction timing and location of hippocampal plasticity.

Directory of Open Access Journals (Sweden)

Noriaki Ohkawa

Full Text Available In the adult hippocampus dentate gyrus (DG, newly born neurons are functionally integrated into existing circuits and play important roles in hippocampus-dependent memory. However, it remains unclear how neural plasticity regulates the integration pattern of new neurons into preexisting circuits. Because dendritic spines are major postsynaptic sites for excitatory inputs, spines of new neurons were visualized by retrovirus-mediated labeling to evaluate integration. Long-term potentiation (LTP was induced at 12, 16, or 21 days postinfection (dpi, at which time new neurons have no, few, or many spines, respectively. The spine expression patterns were investigated at one or two weeks after LTP induction. Induction at 12 dpi increased later spinogenesis, although the new neurons at 12 dpi didn't respond to the stimulus for LTP induction. Induction at 21 dpi transiently mediated spine enlargement. Surprisingly, LTP induction at 16 dpi reduced the spine density of new neurons. All LTP-mediated changes specifically appeared within the LTP-induced layer. Therefore, neural plasticity differentially regulates the integration of new neurons into the activated circuit, dependent on their developmental stage. Consequently, new neurons at different developmental stages may play distinct roles in processing the acquired information by modulating the connectivity of activated circuits via their integration.

Callus induction and plant regeneration of Ulex europaeus

OpenAIRE

Ramírez,Ingrid; Dorta,Fernando; Cuadros-Inostroza,Álvaro; Peña-Cortés,Hugo

2012-01-01

A callus induction and plant regeneration protocol was developed from leaf and thorn explants for the plant Ulex europaeus. Explants were incubated on 2% sucrose half-strength Murashige and Skoog Medium (MS) with various combinations of plant growth regulators and antioxidants. The best frequency of callus and shoot formation was obtained with 2,4-dichlorophenoxyacetic acid (2,4-D) 1 mg/l x kinetin (Kin) 0.2 mg/l (DK Medium; callus induction) and zeatin (Z) 1 mg/l (DK medium; shoot induction)...

Scalable conditional induction variables (CIV) analysis

DEFF Research Database (Denmark)

Oancea, Cosmin Eugen; Rauchwerger, Lawrence

2015-01-01

parallelizing compiler and evaluated its impact on five Fortran benchmarks. We have found that that there are many important loops using CIV subscripts and that our analysis can lead to their scalable parallelization. This in turn has led to the parallelization of the benchmark programs they appear in.......Subscripts using induction variables that cannot be expressed as a formula in terms of the enclosing-loop indices appear in the low-level implementation of common programming abstractions such as filter, or stack operations and pose significant challenges to automatic parallelization. Because...... the complexity of such induction variables is often due to their conditional evaluation across the iteration space of loops we name them Conditional Induction Variables (CIV). This paper presents a flow-sensitive technique that summarizes both such CIV-based and affine subscripts to program level, using the same...

Structured statistical models of inductive reasoning.

Science.gov (United States)

Kemp, Charles; Tenenbaum, Joshua B

2009-01-01

Everyday inductive inferences are often guided by rich background knowledge. Formal models of induction should aim to incorporate this knowledge and should explain how different kinds of knowledge lead to the distinctive patterns of reasoning found in different inductive contexts. This article presents a Bayesian framework that attempts to meet both goals and describes [corrected] 4 applications of the framework: a taxonomic model, a spatial model, a threshold model, and a causal model. Each model makes probabilistic inferences about the extensions of novel properties, but the priors for the 4 models are defined over different kinds of structures that capture different relationships between the categories in a domain. The framework therefore shows how statistical inference can operate over structured background knowledge, and the authors argue that this interaction between structure and statistics is critical for explaining the power and flexibility of human reasoning.

Heavy ion induction linacs for fusion

International Nuclear Information System (INIS)

Bangerter, R.O.; Ho, D.D.M.

1991-01-01

In 1976 Denis Keefe proposed the heavy ion induction linac as a driver for inertial confinement fusion (ICF) power plants. Subsequent research has established that heavy ion fusion (HIF) is potentially an attractive energy source and has identified the issues that must be resolved to make HIF a reality. The principal accelerator issues are achieving adequately low transverse and longitudinal emittance and acceptable cost. Results from the single and multiple beam experiments at LBL on transverse emittance are encouraging. A predicted high current longitudinal instability that can affect longitudinal emittance is currently being studied. This paper presents an overview of economics and ICF target requirements and their relationship to accelerator design. It also presents a summary of the status of heavy ion induction linac research. It concludes with a discussion of research plans, including plans for the proposed Induction Linac Systems Experiments (ILSE)

Suppression of Gain Ripples in Superconducting Traveling-Wave Kinetic Inductance Amplifiers

Science.gov (United States)

Bal, Mustafa; Erickson, Robert P.; Ku, Hsiang Sheng; Wu, Xian; Pappas, David P.

Superconducting traveling-wave kinetic inductance (KIT) amplifiers demonstrated gain over a wide bandwidth with high dynamic range and low noise. However, the gain curve exhibits ripples. Impedance mismatch at the input and output ports of the KIT amplifier as wells as split ground planes of the coplanar waveguide (CPW) geometry are potential contributors to the ripple in the gain curve. Here we study the origin of these ripples in KIT amplifiers configured in CPW geometry using approximately 20 nm thick NbTiN films grown by reactive co-sputtering of NbN and TiN. Our NbTiN films have non-linear kinetic inductance as a function of current, described by L =L0 (1 +(I /I*) 2) , where I* = 15 . 96 +/- 0 . 11 mA measured by time domain reflectometry. We report the results of implementing an impedance taper that takes into account a significantly reduced phase velocity as it narrows, adding Au onto the CPW split grounds, as well as employing different designs of dispersion engineering. Qubit Measurements using KIT amplifiers will also be reported.

Induction and direct resistance heating theory and numerical modeling

CERN Document Server

Lupi, Sergio; Aliferov, Aleksandr

2015-01-01

This book offers broad, detailed coverage of theoretical developments in induction and direct resistance heating and presents new material on the solution of problems in the application of such heating. The physical basis of induction and conduction heating processes is explained, and electromagnetic phenomena in direct resistance and induction heating of flat workpieces and cylindrical bodies are examined in depth. The calculation of electrical and energetic characteristics of induction and conduction heating systems is then thoroughly reviewed. The final two chapters consider analytical solutions and numerical modeling of problems in the application of induction and direct resistance heating, providing industrial engineers with the knowledge needed in order to use numerical tools in the modern design of installations. Other engineers, scientists, and technologists will find the book to be an invaluable reference that will assist in the efficient utilization of electrical energy.

Economic analysis comparing induction of labor and expectant management in women with preterm prelabor rupture of membranes between 34 and 37 weeks (PPROMEXIL trial).

Science.gov (United States)

Vijgen, Sylvia M C; van der Ham, David P; Bijlenga, Denise; van Beek, Johannes J; Bloemenkamp, Kitty W M; Kwee, Anneke; Groenewout, Mariët; Kars, Michael M; Kuppens, Simone; Mantel, Gerald; Molkenboer, Jan F M; Mulder, Antonius L M; Nijhuis, Jan G; Pernet, Paula J M; Porath, Martina; Woiski, Mallory D; Weinans, Martin J N; van Wijngaarden, Wim J; Wildschut, Hajo I J; Akerboom, Bertina; Sikkema, J Marko; Willekes, Christine; Mol, Ben W J; Opmeer, Brent C

2014-04-01

To compare the costs of induction of labor and expectant management in women with preterm prelabor rupture of membranes (PPROM). Economic analysis based on a randomized clinical trial. Obstetric departments of eight academic and 52 non-academic hospitals in the Netherlands. Women with PPROM near term who were not in labor 24 h after PPROM. A cost-minimization analysis was done from a health care provider perspective, using a bottom-up approach to estimate resource utilization, valued with unit-costs reflecting actual costs. Primary health outcome was the incidence of neonatal sepsis. Direct medical costs were estimated from start of randomization to hospital discharge of mother and child. Induction of labor did not significantly reduce the probability of neonatal sepsis [2.6% vs. 4.1%, relative risk 0.64 (95% confidence interval 0.25-1.6)]. Mean costs per woman were €8094 for induction and €7340 for expectant management (difference €754; 95% confidence interval -335 to 1802). This difference predominantly originated in the postpartum period, where the mean costs were €5669 for induction vs. €4801 for expectant management. Delivery costs were higher in women allocated to induction than in women allocated to expectant management (€1777 vs. €1153 per woman). Antepartum costs in the expectant management group were higher because of longer antepartum maternal stays in hospital. In women with pregnancies complicated by PPROM near term, induction of labor does not reduce neonatal sepsis, whereas costs associated with this strategy are probably higher. © 2014 Nordic Federation of Societies of Obstetrics and Gynecology.

Edaravone reduces astrogliosis and apoptosis in young rats with kaolin-induced hydrocephalus.

Science.gov (United States)

Garcia, Camila Araújo Bernardino; Catalão, Carlos Henrique Rocha; Machado, Hélio Rubens; Júnior, Ivair Matias; Romeiro, Thais Helena; Peixoto-Santos, José Eduardo; Santos, Marcelo Volpon; da Silva Lopes, Luiza

2017-03-01

We investigated the possible neuroprotective effects of the free radical scavenger edaravone in experimental hydrocephalus. Seven-day-old Wistar rats were divided into three groups: control group (C), untreated hydrocephalic (H), and hydrocephalic treated with edaravone (EH). The H and EH groups were subjected to hydrocephalus induction by 20% kaolin intracisternal injection. The edaravone (20 mg/kg) was administered daily for 14 days from the induction of hydrocephalus. All animals were daily weighed and submitted to behavioral test and assessment by magnetic resonance imaging. After 14 days, the animals were sacrificed and the brain was removed for histological, immunohistochemical, and biochemical studies. The gain weight was similar between groups from the ninth post-induction day. The open field test performance of EH group was better (p  0.01), germinal matrix (p > 0.05), and cerebral cortex (p > 0.05), as compared to H group. We have demonstrated that administration of edaravone for 14 consecutive days after induction of hydrocephalus reduced astrocyte activity and that it has some beneficial effects over apoptotic cell death.

Digital inductive teaching method of strabismus

OpenAIRE

Zhao-Jiang Du; Peng Li; Li Wang

2015-01-01

AIM: To reform the traditional teaching modes of strabismus by using digital induction to enhance logic in teaching process.METHODS: The study was performed in the group of 20 eight-year program clinical undergraduates from the class of 2009 and 198 five-year program clinical undergraduates from the class of 2010. These students were divided into two groups receiving traditional and digital induction teaching over the same period respectively. After classes, questionnaire survey and classroom...

Using squeeze-film effect to reduce surface friction in electrostatic actuators

DEFF Research Database (Denmark)

Zsurzsan, Tiberiu-Gabriel; Yamamoto, Akio; Zhang, Zhe

2015-01-01

This paper presents a method of reducing load friction in two degrees-of-freedom (2-DOF) transparent electrostatic induction actuator by using vibration-induced squeeze film effect. An experimental set-up was built to prove the concept. An overall 70% reduction in required driving voltage...

Factors influencing callus induction and plant regeneration of ...

African Journals Online (AJOL)

ajl yemi

2012-01-12

). Effect of basal medium on callus induction and plant regeneration. Three different kinds of basal mediums (MS, N6 and SH) were used to investigate their effects on callus induction and regeneration. Significant differences ...

Recirculating induction accelerators for inertial fusion: Prospects and status

International Nuclear Information System (INIS)

Friedman, A.; Barnard, J.J.; Cable, M.D.

1995-01-01

The US is developing the physics and technology of induction accelerators for heavy-ion beam-driven inertial fusion. The recirculating induction accelerator repeatedly passes beams through the same set of accelerating and focusing elements, thereby reducing both the length and gradient of the accelerator structure. This promises an attractive driver cost, if the technical challenges associated with recirculation can be met. Point designs for recirculator drivers were developed in a multi-year study by LLNL, LBNL, and FM Technologies, and that work is briefly reviewed here. To validate major elements of the recirculator concept, we are developing a small (4-5-m diameter) prototype recirculator which will accelerate a space-charge-dominated beam of K + ions through 15 laps, from 80 to 320 keV and from 2 to 8 mA. Transverse beam confinement is effected via permanent-magnet quadrupoles; bending is via electric dipoles. This ''Small Recirculator'' is being developed in a build-and-test sequence of experiments. An injector, matching section, and linear magnetic channel using seven half-lattice periods of permanent-magnet quadrupole lenses are operational. A prototype recirculator half-lattice period is being fabricated. This paper outlines the research program, and presents initial experimental results

Baseline AMH Level Associated With Ovulation Following Ovulation Induction in Women With Polycystic Ovary Syndrome.

Science.gov (United States)

Mumford, Sunni L; Legro, Richard S; Diamond, Michael P; Coutifaris, Christos; Steiner, Anne Z; Schlaff, William D; Alvero, Ruben; Christman, Gregory M; Casson, Peter R; Huang, Hao; Santoro, Nanette; Eisenberg, Esther; Zhang, Heping; Cedars, Marcelle I

2016-09-01

Anti-Müllerian hormone (AMH) reduces aromatase activity and sensitivity of follicles to FSH stimulation. Therefore, elevated serum AMH may indicate a higher threshold for response to ovulation induction in women with polycystic ovary syndrome (PCOS). This study sought to determine the association between AMH levels and ovulatory response to treatment among the women enrolled into the Pregnancy in PCOS II (PPCOS II) trial. This was a secondary analysis of data from a randomized clinical trial in academic health centers throughout the United States Participants: A total of 748 women age 18-40 years, with PCOS and measured AMH levels at baseline, were included in this study. Couples were followed for up to five treatment cycles to determine ovulation (midluteal serum progesterone > 5 ng/mL) and the dose required to achieve ovulation. A lower mean AMH and AMH per follicle was observed among women who ovulated compared with women who never achieved ovulation during the study (geometric mean AMH, 5.54 vs 7.35 ng/mL; P = .0001; geometric mean AMH per follicle, 0.14 vs 0.18; P = .01) after adjustment for age, body mass index, T, and insulin level. As AMH levels increased, the dose of ovulation induction medication needed to achieve ovulation also increased. No associations were observed between antral follicle count and ovulation. These results suggest that high serum AMH is associated with a reduced response to ovulation induction among women with PCOS. Women with higher AMH levels may require higher doses of medication to achieve ovulation.