WorldWideScience

Sample records for equipements thermiques industriels

  1. Process insulation. Isolation thermique des equipements

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    A manual is presented to assist managers and operating personnel to recognize industrial energy management opportunities, and provides mathematical equations, general information on proven techniques and technology, and examples. It deals with process insulation, focusing on the insulation of mechanical systems such as piping, process vessels, equipment, and ductwork. The manual describes the effects of insulation materials; commonly encountered types of insulation, coverings and protective finishes as well as common applications; energy management opportunities, divided into housekeeping, low cost, and retrofit; and includes worked examples of each. Includes glossary. 17 figs., 8 tabs.

  2. Stockage thermique saisonnier par puits geothermiques pour batiments residentiels equipes de panneaux photovoltaiques-thermiques

    Science.gov (United States)

    Brischoux, Pauline

    The energy efficiency of a ground-source heat pump system with solar heat injection from photovoltaic-thermal panels is evaluated. The system provides heat to a single-family house located in Montreal. Unlike conventional GSHP systems, the borehole, or boreholes, is equipped with two independent fluid circuits. Thus, it is possible to inject heat from the solar panels and extract energy with the heat pump simultaneously. First, the system is analyzed with a single borehole using numerical simulations within the TRNSYS environment. Results show that the heat injection in the borehole increases the efficiency of the system and limits the reduction in performance caused by unbalanced ground loads. However, part of the heat injected during the summer is lost by thermal diffusion to the ground surrounding the borehole and a single borehole is not appropriate for seasonal thermal energy storage. A study of the same system is performed after replacing the single borehole by a borefield consisting of 15 shallow boreholes. This analysis points out the technical feasibility of seasonal borehole thermal energy storage (BTES) systems for residential applications. Such a system reaches a higher energy efficiency than the system including a single borehole with solar charging but requires a large storage volume. The last part of this thesis presents a preliminary study of an ice storage system. The results are compared to the BTES in terms of energy efficiency and needed configuration. The system with BTES requires a large storage volume but achieves a high overall energy efficiency. The ice storage system involves a much smaller storage volume but does not seem to be able to reach an energy efficiency similar to the BTES, the heat pump inlet temperature being limited by the low storage temperature. However, the overall energy efficiency of this system is similar to conventional GSHP systems, i.e. without solar charging.

  3. Les performances mécaniques et thermiques d’un béton léger à base de déchets industriels solides et de granulats de bois

    Directory of Open Access Journals (Sweden)

    Mohamed Larbi Benmalek

    2014-04-01

    Les résultats expérimentaux montrent qu’à densité égale, les matériaux élaborés sont mécaniquement et thermiquement compétitifs. Ils sont intéressants du point de vue confort et stockage thermiques.

  4. The point of view of thermal equipment users; Le point de vue des gestionnaires d`equipements thermiques

    Energy Technology Data Exchange (ETDEWEB)

    Barroyer, P. [Compagnie Generale de Chauffe, 59 - Saint Andre Lez Lille (France)

    1997-12-31

    The influence of new pollution regulations in France on the operation of thermal equipment for central heating systems or industrial heat process systems, is examined. The main French regulations concerning air pollution control and energy rational consumption are reviewed, and their effects on the design, equipment, operation and costs of heat plants are discussed: impacts of the decree on upgrading and disposal of fossil fuel ashes, the decree on special protection zone (large cities), the clean air law, the compulsory declaration for classified combustion plants and limit air pollution emission levels

  5. The point of view from thermal equipment managers; Le point de vue des gestionnaires d`equipements thermiques

    Energy Technology Data Exchange (ETDEWEB)

    Barroyeur, P. [Compagnie General de Chauffe, 59 - Saint Andre Lez Lille (France)

    1997-12-31

    The new French regulations on air pollution and classified installations have increased the technical and economical constraints of thermal equipment managers in the domain of collective space heating and industrial heating. The aim of this paper is to precise the impact of these regulations in particular, on the valorization and elimination of fossil fuel ashes, and on the design, operation and maintenance of combustion installations (maximum acceptable limits of pollutant emissions). (J.S.)

  6. Valorisation de chaleur à bas niveau thermique Upgrading Low-Thermal-Level Heat

    OpenAIRE

    Cohen G.; Rojey A.

    2006-01-01

    La mise en oeuvre à la fois de cycles thermodynamiques et de fluides adaptés permet d'élargir considérablement les possibilités de récupération et de valorisation de la chaleur à bas niveau contenue dans les rejets thermiques industriels, l'eau géothermale, le rayonnement solaire ou le milieu environnant. Ceci permettra une meilleure préservation des ressources énergétiques dans les principaux secteurs consommateurs d'énergie : résidentiel, tertiaire et industriel. On décrit les possibilités ...

  7. Photothermal radiometry applied to characterization and control of thermal contact resistance of crimped metals; Radiometrie photothermique appliquee a la caracterisation et au controle de la resistance thermique de contact de metaux sertis

    Energy Technology Data Exchange (ETDEWEB)

    Van Schel, Etienne

    1989-11-15

    Modulated photothermal radiometry is used to study the thermal contact between two metals. At first, two models using a bidimensional axisymmetric geometry are proposed to describe the interface: the first one deals with thermal contact resistance, the second one with an equivalent layer. A thorough calculation of the photothermal signal taking into account the nature of the sample and the detection is here presented. Theoretical simulations show the influence of several parameters (frequency. dimensions of the excitation and the detection) on the sensitivity of the method applied to the detection of the thermal resistance. The comparison, with a three layer-model justifies the use of thermal resistance in periodical regime, for air layers between metals. Then, we present an experimental device that is used to validate the model. The results, obtained on duralumin-copper samples, show the sensitivity of the method and lead us to propose values of thermal contact resistance for different crimpings. At last an industrial testing equipment is described. The results, obtained on laboratory samples, are confirmed. Heat exchanger pipes, including voluntary defects are tested. Thanks to this device, we are able to make an in situ crimping control that can also be applied to other types of contacts. [French] La radiometrie photothermique est utilisee pour etudier le contact thermique entre deux metaux. Tout d'abord, deux modeles utilisant une geometrie bidimensionnelle axisymetrique sont proposes pour decrire l'interface: le premier utilise une resistance thermique de contact, le second un milieu equivalent Un calcul complet du signal photothermique, prenant en compte la nature de l'echantillon et de la detection, est presente. Des simulations theoriques montrent l'influence de quelques parametres (frequence, dimensions de l'excitation et de la detection) sur la sensibilite de la methode a la detection de la resistance thermique. La comparaison, avec un modele a trois

  8. Combustion and regulations. Impacts of new regulations on medium-power thermal equipment (boilers, engines, turbines, dryers and furnaces); Combustion et reglementation. Incidences des nouvelles reglementations sur les equipements thermiques de moyenne puissance (chaudieres, moteurs, turbines, secheurs et fours)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This conference is composed of 20 papers on the influence of French and European new pollution regulations on medium size thermal equipment such as boilers, engines, turbines, dryers and furnaces. It is discussed what is going to change with new regulations, how they will apply to existing plants, what will be the impact on future equipment costs. The evolution of energy suppliers and equipment manufacturers facing these new regulations is also examined: fuel substitution, improvements in turbines and engines with water injection and special chambers, diesel engine control, lean mixtures and electronic control for gas engines... Means for reducing SOx, NOx and ash emission levels in boilers are also examined

  9. INFLUENCE DE L’EPAISSEUR SUR LE COEFFICIENT DE DILATATION THERMIQUE DE LA TOLE ALMGSI

    Directory of Open Access Journals (Sweden)

    S SAADALLAH

    2014-12-01

    Full Text Available L’objectif de cet article est l’étude de l’influence de l’épaisseur sur le coefficient de dilatation thermique de la tôle AlMgSi. Les résultats obtenus dépendent fortement de l’épaisseur. Les courbes dilatométriques varient d’une direction à une autre. Il y a présence d’une anisotropie dont l’intensité dépend de l’épaisseur et de la direction de mesure. L’échantillon prélevé selon la direction Y et dont l’épaisseur est de 1.15mm présente une dilatation faible devant les autres. Ce comportement le rend intéressant dans le domaine industriel.

  10. Thermal systems; Systemes thermiques

    Energy Technology Data Exchange (ETDEWEB)

    Lalot, S. [Valenciennes Univ. et du Hainaut Cambresis, LME, 59 (France); Lecoeuche, S. [Ecole des Mines de Douai, Dept. GIP, 59 - Douai (France)]|[Lille Univ. des Sciences et Technologies, 59 - Villeneuve d' Ascq (France); Ahmad, M.; Sallee, H.; Quenard, D. [CSTB, 38 - Saint Martin d' Heres (France); Bontemps, A. [Universite Joseph Fourier, LEGI/GRETh, 38 - Grenoble (France); Gascoin, N.; Gillard, P.; Bernard, S. [Laboratoire d' Energetique, Explosion, Structure, 18 - Bourges (France); Gascoin, N.; Toure, Y. [Laboratoire Vision et Robotique, 18 - Bourges (France); Daniau, E.; Bouchez, M. [MBDA, 18 - Bourges (France); Dobrovicescu, A.; Stanciu, D. [Bucarest Univ. Polytechnique, Faculte de Genie Mecanique (Romania); Stoian, M. [Reims Univ. Champagne Ardenne, Faculte des Sciences, UTAP/LTM, 51 (France); Bruch, A.; Fourmigue, J.F.; Colasson, S. [CEA Grenoble, Lab. Greth, 38 (France); Bontemps, A. [Universite Joseph Fourier, LEGI/GRETh, 38 - Grenoble (France); Voicu, I.; Mare, T.; Miriel, J. [Institut National des Sciences Appliquees (INSA), LGCGM, IUT, 35 - Rennes (France); Galanis, N. [Sherbrooke Univ., Genie Mecanique, QC (Canada); Nemer, M.; Clodic, D. [Ecole des Mines de Paris, Centre Energetique et Procedes, 75 (France); Lasbet, Y.; Auvity, B.; Castelain, C.; Peerhossaini, H. [Nantes Univ., Ecole Polytechnique, Lab. de Thermocinetiquede Nantes, UMR-CNRS 6607, 44 (France)

    2005-07-01

    This session about thermal systems gathers 26 articles dealing with: neural model of a compact heat exchanger; experimental study and numerical simulation of the thermal behaviour of test-cells with walls made of a combination of phase change materials and super-insulating materials; hydraulic and thermal modeling of a supercritical fluid with pyrolysis inside a heated channel: pre-dimensioning of an experimental study; energy analysis of the heat recovery devices of a cryogenic system; numerical simulation of the thermo-hydraulic behaviour of a supercritical CO{sub 2} flow inside a vertical tube; mixed convection inside dual-tube exchangers; development of a nodal approach with homogenization for the simulation of the brazing cycle of a heat exchanger; chaotic exchanger for the cooling of low temperature fuel cells; structural optimization of the internal fins of a cylindrical generator; a new experimental approach for the study of the local boiling inside the channels of exchangers with plates and fins; experimental study of the flow regimes of boiling hydrocarbons on a bundle of staggered tubes; energy study of heat recovery exchangers used in Claude-type refrigerating systems; general model of Carnot engine submitted to various operating constraints; the free pistons Stirling cogeneration system; natural gas supplied cogeneration system with polymer membrane fuel cell; influence of the CRN coating on the heat flux inside the tool during the wood unrolling process; transport and mixture of a passive scalar injected inside the wake of a Ahmed body; control of a laser welding-brazing process by infrared thermography; 2D self-adaptative method for contours detection: application to the images of an aniso-thermal jet; exergy and exergy-economical study of an 'Ericsson' engine-based micro-cogeneration system; simplified air-conditioning of telephone switching equipments; parametric study of the 'low-energy' individual dwelling; brief synthesis of

  11. Valorisation de chaleur à bas niveau thermique Upgrading Low-Thermal-Level Heat

    Directory of Open Access Journals (Sweden)

    Cohen G.

    2006-11-01

    Full Text Available La mise en oeuvre à la fois de cycles thermodynamiques et de fluides adaptés permet d'élargir considérablement les possibilités de récupération et de valorisation de la chaleur à bas niveau contenue dans les rejets thermiques industriels, l'eau géothermale, le rayonnement solaire ou le milieu environnant. Ceci permettra une meilleure préservation des ressources énergétiques dans les principaux secteurs consommateurs d'énergie : résidentiel, tertiaire et industriel. On décrit les possibilités que présentent : - Les cycles thermodynamiques directs (pompes de chaleur à compression ou à absorption dans le domaine du chauffage résidentiel et tertiaire où elles sont déjà bien implantées et dont les applications commencent à pénétrer le secteur industriel. - Les cycles thermodynamiques inverses (thermotransformateurs et cycles moteurs à fluide organique pour lesquels les progrès techniques accomplis et l'accroissement du prix de l'énergie devraient permettre d'en assurer la diffusion progressive dans le secteur industriel. The implementation of both thermodynamic cycles and suitable fluids makes for a considerable widening of the capacity to recover and upgrade the low-level heat contained in industrial heat wastes, geothermal water, solar radiation or the surrounding environment. This will make for better conservation of energy resources in the leading sectors of energy consumption, i. e. residential, tertiary and industrial. This article describes these possibilities in the form of: (a Direct thermodynamic cycles (compression or absorption heat pumps in the field of home and tertiary heating where they have already obtained a solid foothold and for which applications are beginning te penetrate into the industrial sector. (b Reverse thermodynamic cycles (heat transformers and organic-fluid motor cycles for which the technical advances made and the increase in energy prices should enable them to spread progressively

  12. Industrial gases. Special issue; Industriele gassen. Thema

    Energy Technology Data Exchange (ETDEWEB)

    De Boer, A.; Voermans, F. (ed.)

    2004-07-01

    In three articles attention is paid to the use of synthesis gas in the Netherlands. In the first article the growing market for synthesis gas is discussed, in the second article it is argued that the energy efficiency of the production of nitrogen can be improved, and the third article is about cooling an ice track by means of carbon dioxide. [Dutch] In 3 artikelen wordt aandacht besteed aan het gebruik van industriele gassen. In het eerste artikel wordt de sterk groeiende markt voor synthese gas besproken, in het tweede artikel wordt aangegeven hoe de efficiency van stikstofproduktie kan worden verbeterd, en het derde artikele gaat in op het gebruik van kooldioxide in de koeling van een ijsbaan.

  13. Thermal diffusion (1963); Diffusion thermique (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Lemarechal, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    This report brings together the essential principles of thermal diffusion in the liquid and gaseous phases. The macroscopic and molecular aspects of the thermal diffusion constant are reviewed, as well as the various measurement method; the most important developments however concern the operation of the CLUSIUS and DICKEL thermo-gravitational column and its applications. (author) [French] Ce rapport rassemble les principes essentiels de la diffusion thermique en phase liquide et en phase gazeuse. Les aspects macroscopique et moleculaire de la constante de diffusion thermique sont passes en revue ainsi que ses differentes methodes de mesure; mais les developpements les plus importants concernent le fonctionnement de ls colonne thermogravitationnelle de CLUSIUS et DICKEL et ses applications. (auteur)

  14. Space heating in buildings: thermal diagnosis of an industrial building; Chauffage des batiments: bilan thermique d`un batiment industriel

    Energy Technology Data Exchange (ETDEWEB)

    Brunet, R.

    1996-12-31

    The various heat transfer equations used for calculations in thermal diagnosis of an industrial building are reviewed: calculation of the heat losses through walls as a function of building materials, calculation of the energy consumption for heating fresh air (as a function of the air pollution rate in the building), calculation of the total heat losses, the heating energy demand and the annual energy consumption. Data concerning building materials characteristics, insulation and heating loads in the various regions of France, are also presented

  15. impacts des rejets industriels sur les eaux souterraines

    African Journals Online (AJOL)

    USER

    pollution et sont nombreuses, notamment les usines sidérurgiques, métalliques et pétrochimiques. Leurs rejets ont des effets néfastes sur les eaux de la région. Actuellement, les effluents industriels situés dans la région de Berrahal, contiennent d'importantes quantités de produits chimiques organiques et inorganiques et ...

  16. Nouvelles approches ergonomiques de la cartographie des risques industriels

    Directory of Open Access Journals (Sweden)

    Éliane Propeck-Zimmermann

    2009-12-01

    Full Text Available Les cartes actuelles présentent des insuffisances pour une gestion territoriale des risques industriels. En redéfinissant le concept de «situation à risques» et en l'implémentant dans un SIG, on peut disposer à la demande d'informations riches et variées: cartes analytiques, de synthèse, typologies, requêtes spatiales diverses. Les recherches en cours visent à développer une interface ergonomique pour faciliter la concertation entre différents acteurs.

  17. Caracterisation thermique de modules de refroidissement pour la photovoltaique concentree

    Science.gov (United States)

    Collin, Louis-Michel

    Pour rentabiliser la technologie des cellules solaires, une reduction du cout d'exploitation et de fabrication est necessaire. L'utilisation de materiaux photovoltaiques a un impact appreciable sur le prix final par quantite d'energie produite. Une technologie en developpement consiste a concentrer la lumiere sur les cellules solaires afin de reduire cette quantite de materiaux. Or, concentrer la lumiere augmente la temperature de la cellule et diminue ainsi son efficacite. Il faut donc assurer a la cellule un refroidissement efficace. La charge thermique a evacuer de la cellule passe au travers du recepteur, soit la composante soutenant physiquement la cellule. Le recepteur transmet le flux thermique de la cellule a un systeme de refroidissement. L'ensemble recepteur-systeme de refroidissement se nomme module de refroidissement. Habituellement, la surface du recepteur est plus grande que celle de la cellule. La chaleur se propage donc lateralement dans le recepteur au fur et a mesure qu'elle traverse le recepteur. Une telle propagation de la chaleur fournit une plus grande surface effective, reduisant la resistance thermique apparente des interfaces thermiques et du systeme de refroidissement en aval vers le module de refroidissement. Actuellement, aucune installation ni methode ne semble exister afin de caracteriser les performances thermiques des recepteurs. Ce projet traite d'une nouvelle technique de caracterisation pour definir la diffusion thermique du recepteur a l'interieur d'un module de refroidissement. Des indices de performance sont issus de resistances thermiques mesurees experimentalement sur les modules. Une plateforme de caracterisation est realisee afin de mesurer experimentalement les criteres de performance. Cette plateforme injecte un flux thermique controle sur une zone localisee de la surface superieure du recepteur. L'injection de chaleur remplace le flux thermique normalement fourni par la cellule. Un systeme de refroidissement est installe

  18. 1 Etude thermique expérimentale des suspensions non ...

    African Journals Online (AJOL)

    FAGLA

    3Laboratoire de Caractérisation Thermophysique des Matériaux et .... [6] ont étudié le stockage et de distribution du froid par chaleur latente en traitant, ...... siège du meilleur échange thermique, d‟où le nombre de Nusselt le plus élevé).

  19. Reduction de la sensation des malaises thermiques: determination ...

    African Journals Online (AJOL)

    La présente étude a pour objet de contribuer à la réduction de la sensation des malaises thermiques à travers la recherche des orientations préférentielles des bâtiments dans les différentes zones du Togo à partir des conditions aérodynamiques et climatiques locales. Les données climatiques à savoir la température, ...

  20. Thermal diffusivity of solids; Diffusivite thermique des solides

    Energy Technology Data Exchange (ETDEWEB)

    Kleimann, H; Fetiveau, Y; Richard, M; Eyraud, L; Eyraud, C; Elston, J [Institut National des Sciences Appliquees, Lyon (France); Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-07-01

    The authors recall the different methods of thermal diffusivity measurements and point out the possible causes of errors. They study in particular the sinusoidal methods of thermal attack using the measurement of either an amplitude or a phase, in which the controlled energy in-put is obtained either by Joule effect or by radiation. By the use of controlled systems, it is possible to apply those methods to the measurement of thermal diffusivity of their samples in a large scale of temperature. The authors describe their experimental achievements and give several results dealing especially with Al{sub 2}O{sub 3}, BeO, MgO. (author) [French] Les auteurs rappellent les diverses methodes de mesure de la diffusivite thermique et indiquent les sources d'erreurs possibles. Ils etudient particulierement les methodes d'attaque thermique sinusoidales utilisant soit une mesure d'amplitude, soit une mesure de phase dans lesquelles l'apport energetique controle est effectue soit par effet Joule, soit par rayonnement. La mise en oeuvre de systemes asservis permet l'utilisation de ces methodes pour la mesure de la diffusivite thermique d'echantillons minces dans une gamme etendue de temperature. Les auteurs decrivent les realisations experimentales et fournissent divers resultats concernant notamment Al{sub 2}O{sub 3}, BeO, MgO. (auteur)

  1. Elaboration et Suivi des Budgets de Marketing Industriel: le Système ADVISOR

    OpenAIRE

    Choffray, Jean-Marie; Delabre, Gilles

    1982-01-01

    Cet article revoit les problèmes posés par l'élaboration et le suivi des budgets de marketing dans un environnement industriel. Il présente le système ADVISOR pour lequel nous avons développé un programme interactif adapté aux besoins des entreprises Françaises.

  2. Draught control by means of industrial air curtains. Background information on the design of industrial air curtains; Tochtbestrijding met industriele luchtgordijnen. Achtergronden bij ontwerp van industriele luchtgrodijnen

    Energy Technology Data Exchange (ETDEWEB)

    Cremers, B. [Biddle, Kootstertille (Netherlands); Traversar, R. [TNO Milieu, Energie en Procesinnovatie TNO-MEP, Apeldoorn (Netherlands)

    2008-02-15

    In industrial buildings a balanced ventilation is not common property. Due to increasing differences in pressure across the front much cold outside air enters the building, resulting in poor comfort near the door. A good air curtain can heat up large amounts of incoming cold outside air in such a way that energy saving is optimal and comfort remains high. (mk) [Dutch] Bij industriele gebouwen is gebalanceerde ventilatie geen gemeengoed. Door oplopende drukverschillen over de gevel komt veel koude buitenlucht naar binnen en is het comfort vlak achter de deur erg laag. Een goed luchtgordijn kan grote hoeveelheden binnenkomende koude buitenlucht zodanig opwarmen dat de energiebesparing optimaal is en het comfort hoog blijft.

  3. Generative Fertigung im Maschinenbau - industrieller 3D-Druck auf dem Weg in die Serienproduktion

    OpenAIRE

    Müller, Bernhard

    2014-01-01

    3D-Druck ist aktuell medial omnipräsent, sein Potential für echte industrielle Anwendungen, v. a. im Maschinenbauumfeld, wird kontrovers diskutiert. Der Vortrag gibt einen fundierten Einblick in den Stand der Technik zum industriellen 3D-Druck (Generative Fertigung , Additive Manufacturing) und zeigt spezifische Potentiale mit industrieller Relevanz auf. Dabei werden ebenso Praxisbeispiele aus heutiger Anwendung in der Industrie gezeigt als auch Zukunftsszenarien für potentielle Anwendungen e...

  4. DESIGNOR: une méthode nouvelle d'aide à la conception des produits industriels

    OpenAIRE

    Choffray, Jean-Marie

    1980-01-01

    Cet article présente une méthode nouvelle, appelée DESIGNOR, d'aide à la décision marketing. Son objectif est d'accroître la créativité au cours du processus de développement d'un nouveau produit industriel et de réduire les risques d'échec commercial.

  5. Thermal and Hydrolytic Stability of Dithiophophoric Acids Stabilité thermique et hydrolytique des acides dithiophosphoriques

    Directory of Open Access Journals (Sweden)

    Ivanov S. K.

    2006-11-01

    Full Text Available The thermal and hydrolytic stability of dibutyl-, diisobutyl- and diisooctyldithiophosphoric acids have been studied in the range of 40-80°C. The reaction progress was followed by the H2S evolution kinetics in volumetric equipment at constant pressure, equal to the barometric one. The kinetic parameters of the process have been determined at various acid water ratios - maximum rates of gas evolution, activation energy and the kinetic order. It has been shown that the hydrolysis proceeds mainly along the sulph-hydrate group of the acid (up to temperatures of 60°C, while at higher temperatures the ester groups and the thion sulphur are attacked too. The thermal stability of dithiophosphoric acids has been studied in the presence of stainless steel, lead and copper plates. It has been shown that stainless steel doesn't affect the process rate, while copper and especially lead increase the gas evolution and decrease the activation energy. A model describing the reaction progress at the interfacial surfaces - organic phase, water and metal surface - has been developed. Based on these data a conclusion is advanced, related to the manifacture technology of antioxidant, anticorrosion and antiwear additives of the zinc dialkyldithiophosphate type. It is pointed out that the neutralization process of dithiophosphoric acids should be carried out in a stainless steel reactor at tempeatures below 70°C. Le présent article s'efforce d'élucider l'influence de l'eau, de la température et des surfaces métalliques sur la stabilité thermique et hydrolytique des acides dibutyl-, diisobutyl- et diisooctyldithiophosphoriques, à la lumière du concept d'interaction.

  6. Les Parcs Industriels Fournisseurs ou le choix de la proximité géographique

    OpenAIRE

    Sonia Adam-Ledunois; Jérôme Guédon; Sophie Renault

    2008-01-01

    International audience; La proximité géographique est régulièrement présentée comme le remède à de nombreux maux, la solution à des relations distendues voire rompues, et cela tant sur un plan social qu'économique. Nombre de décisions ou démarches, civiles, politiques ou stratégiques, placent ainsi la proximité au cœur des dispositifs envisagés (emplois de proximité, police de proximité, fête des voisins, pôle de compétitivité, systèmes de production localisés, districts industriels, etc.). L...

  7. Evolution des quasiparticules nodales du cuprate supraconducteur YBa2Cu3Oy en conductivite thermique

    Science.gov (United States)

    Rene de Cotret, Samuel

    Ce memoire presente des mesures de conductivite thermique sur les supraconducteurs YBCO et Tl-2201 afin de statuer sur la presence possible d'un point critique quantique (QCP) dans le diagramme de phase de cuprates. Ce point critique quantique serait a l'origine de la reconstruction de la surface de Fermi, d'un large cylindre de trous en de petites poches de trous et d'electrons. La conductivite thermique dans le regime T → 0 permet d'extraire une quantite purement electronique liee aux vitesses de Fermi et du gap, au noeud. Une discontinuite dans cette quantite pourrait signaler la traversee du dopage critique qui reconstruit la surface de Fermi. Plusieurs sondes experimentales distinguent une transition de phase ou un crossover a T* a temperature finie. D'autres sondes mettent en evidence une transition de phase sous l'effet d'un champ magnetique. La presence ou non de cet ordre, a temperature et champ magnetique nul questionne la communaute depuis plusieurs annees. Dans cette etude, nous detectons une variation brusque de kappa0/T a p = 0.18 dans YBCO et a p = 0.20 dans Tl-2201. Ces sauts sont interpretes comme un signe de la transition a temperature nulle et sont en faveur d'un QCP. Le manque de donnees d'un meme materiau a ces dopages ne permet pas de valider hors de tout doute l'existence d'un point critique quantique. Le modele theorique YRZ decrit aussi bien les donnees de conductivite thermique. Des pistes de travaux experimentaux a poursuivre sont proposees pour determiner la presence ou non du QCP de facon franche. Mots-cles : Supraconducteurs, cuprates, conductivite thermique, point critique quantique.

  8. Prediction du profil de durete de l'acier AISI 4340 traite thermiquement au laser

    Science.gov (United States)

    Maamri, Ilyes

    Les traitements thermiques de surfaces sont des procedes qui visent a conferer au coeur et a la surface des pieces mecaniques des proprietes differentes. Ils permettent d'ameliorer la resistance a l'usure et a la fatigue en durcissant les zones critiques superficielles par des apports thermiques courts et localises. Parmi les procedes qui se distinguent par leur capacite en terme de puissance surfacique, le traitement thermique de surface au laser offre des cycles thermiques rapides, localises et precis tout en limitant les risques de deformations indesirables. Les proprietes mecaniques de la zone durcie obtenue par ce procede dependent des proprietes physicochimiques du materiau a traiter et de plusieurs parametres du procede. Pour etre en mesure d'exploiter adequatement les ressources qu'offre ce procede, il est necessaire de developper des strategies permettant de controler et regler les parametres de maniere a produire avec precision les caracteristiques desirees pour la surface durcie sans recourir au classique long et couteux processus essai-erreur. L'objectif du projet consiste donc a developper des modeles pour predire le profil de durete dans le cas de traitement thermique de pieces en acier AISI 4340. Pour comprendre le comportement du procede et evaluer les effets des differents parametres sur la qualite du traitement, une etude de sensibilite a ete menee en se basant sur une planification experimentale structuree combinee a des techniques d'analyse statistiques eprouvees. Les resultats de cette etude ont permis l'identification des variables les plus pertinentes a exploiter pour la modelisation. Suite a cette analyse et dans le but d'elaborer un premier modele, deux techniques de modelisation ont ete considerees, soient la regression multiple et les reseaux de neurones. Les deux techniques ont conduit a des modeles de qualite acceptable avec une precision d'environ 90%. Pour ameliorer les performances des modeles a base de reseaux de neurones, deux

  9. Numerical and experimental investigation of industrial electrostatic precipitators; Etude numerique et experimentale d`electrofiltres industriels

    Energy Technology Data Exchange (ETDEWEB)

    Tochon, P.

    1997-10-17

    This work deals with electrostatic precipitators or ESP used for gas-solid particles separation. By means of a dust-controlled testing loop created and realised at the GRETh`s plate-form (Research Group on Heat Exchangers) and a numerical model developed during this work from TRIO software, the study of the performances of different ESP geometries has been carried out. Many electrical, hydraulic and particular parameters governing solid particles collection under ionised electric field have been identified, measured and modelled. The numerical model, ratified with experimental data obtained during this study and from literature, allows to describe local and global phenomena occurring in any geometries. Furthermore, parametric studies have been carried out in order to propose some optimised geometries. allowing to increase collection efficiencies. At least, on-site measurements with CETIAT (Centre Technique des Industries Aerauliques et Thermiques) allow to identify dust particles likely to be thrown out to the atmosphere, and troubles peculiar to large scales industrial plants. The numerical model has also been tested on these data. At the end of this study, an efficient dust-controlled experimental tool, PACIFIC loop, and a numerical simulation allowing ESP sizing are available. (author)

  10. Simulation of the thermal behaviour of electric industrial resistance furnaces using the I-DEAS/TMG code; Simulation du comportement thermique des fours electriques industriels a resistances a l`aide du code I-DEAS/TMG

    Energy Technology Data Exchange (ETDEWEB)

    Plard, Ch; Branchu, K; Le Cloirec, B [Electricite de France, 77 - Moret sur Loing (France). Direction des Etudes et Recherches

    1997-12-31

    In order to answer the modeling needs of manufacturers and users of electrical resistance furnaces, Electricite de France (EdF) has been appealed to search for a numerical simulation tool for the modeling of thermal phenomena and to carry out its qualification. The TNG software has been retained according to its modeling characteristics of radiant heat transfers and to the coupling with thermal conduction. After a description of the main characteristics of this code, two examples of application to electrical furnaces are presented. The first example illustrates how it can be possible to accurately reproduce the behaviour of a big industrial furnace. The second example is an illustration of numerical simulation possibilities for the optimization of processes performed with an electric furnace. (J.S.)

  11. Simulation of the thermal behaviour of electric industrial resistance furnaces using the I-DEAS/TMG code; Simulation du comportement thermique des fours electriques industriels a resistances a l`aide du code I-DEAS/TMG

    Energy Technology Data Exchange (ETDEWEB)

    Plard, Ch.; Branchu, K.; Le Cloirec, B. [Electricite de France, 77 - Moret sur Loing (France). Direction des Etudes et Recherches

    1996-12-31

    In order to answer the modeling needs of manufacturers and users of electrical resistance furnaces, Electricite de France (EdF) has been appealed to search for a numerical simulation tool for the modeling of thermal phenomena and to carry out its qualification. The TNG software has been retained according to its modeling characteristics of radiant heat transfers and to the coupling with thermal conduction. After a description of the main characteristics of this code, two examples of application to electrical furnaces are presented. The first example illustrates how it can be possible to accurately reproduce the behaviour of a big industrial furnace. The second example is an illustration of numerical simulation possibilities for the optimization of processes performed with an electric furnace. (J.S.)

  12. TRANSFERT THERMIQUE INSTATIONNAIRE DANS UN MUR TRICOUCHES SUBISSANT UN CHANGEMENT DE PHASE PAR SOLIDIFICATION.

    OpenAIRE

    O Arfi; E Mezaache

    2016-01-01

    Une étude numérique du transfert de chaleur instationnaire dans un mur tricouches est présentée. Le modèle physique est basé sur l’équation de conduction thermique unidirectionnelle en tenant compte des équations de couplages au niveau des interfaces et des conditions convectives de surfaces. Les équations de transfert sont données en représentation enthalpique pour le matériau à changement de phase (MCP), et en formulation générale pour les régions solides. La formulation adimensionnelle a p...

  13. Underground seasonal storage of industrial waste heat; Saisonale Speicherung industrieller Abwaerme im Untergrund

    Energy Technology Data Exchange (ETDEWEB)

    Reuss, M.; Mueller, J. [Bayerische Landesanstalt fuer Landtechnik, TU Muenchen-Weihenstephan, Freising (Germany)

    1998-12-31

    The thermal efficiency of subject systems, especially at higher temperatures is influenced by heat and humidity transport underground. Thermal conductivity and specific thermal capacity depend on the humidity content of the soil. A simulation model was developed that describes the coupled heat and humidity transport in the temperature range up to 90 C. This model will be validated in laboratory and field tests and then be used for designing and analysing underground stores. Pilot plants for the storage of industrial waste heat were designed and planned on the basis of this simulation. In both cases these are cogeneration plants whose waste heat was to be used for space heating and as process energy. Both plants have a very high demand of electric energy which is mostly supplied by the cogeneration plant. The waste heat is put into the store during the summer. In the winter heat is supplied by both the store and the cogeneration plant. In both cases the store has a volume of approx. 15,000 cubic metres with 140 and 210 pits located in a depth of 30 and 40 metres. The plants are used to carry out extensive measurements for the validation of simulation models. (orig.) [Deutsch] Die thermische Leistungsfaehigkeit solcher Systeme wird insbesondere im hoeheren Temperaturbereich durch den Waerme- und Feuchtetransport im Untergrund beeinflusst. Sowohl die Waermeleitfaehigkeit als auch die spezifische Waermekapazitaet sind vom Feuchtegehalt des Bodens abhaengig. Es wurde ein Simulationsmodell entwickelt, das den gekoppelten Waerme- und Feuchtetransport im Temperaturbereich bis 90 C beschreibt. Dieses Modell wird an Labor- und Feldexperimenten validiert und dient dann zur Auslegung und Analyse von Erdwaermesonden-Speichern. Basierend auf diesen theoretischen Grundlagenarbeiten wurden Pilotanlagen zur saisonalen Speicherung industrieller Abwaerme ausgelegt und geplant. In beiden Faellen handelt es sich um Kraft/Waermekopplungsanlagen, deren Abwaerme zur Gebaeudeheizung und

  14. Sociologie du travail et critique du temps industriel The Sociology of Labor and a critical vision of industrial Time

    Directory of Open Access Journals (Sweden)

    Jens Thoemmes

    2009-07-01

    Full Text Available La sociologie du travail a développé un point de vue particulier sur l'analyse des temporalités sociales. L'objectif de cet article est de montrer l'élaboration progressive d'une critique d'un temps industriel unique et unifiant. Cette critique s'appuie sur trois éléments : la multiplicité des temporalités de l’activité professionnelle, le caractère déstructurant du travail industriel et l'émergence d'un temps des loisirs. Ce point de vue a été élaboré par la sociologie du travail en France après 1945, notamment par Georges Friedmann, Pierre Naville et William Grossin.  Avant d’aborder cette période nous voudrions  interroger le moment de la fondation de la sociologie. En mobilisant des travaux peu connus de Max Weber sur le travail, nous verrons en quoi il est un précurseur de l’analyse des attitudes diversifiées des individus et des collectifs à l’égard du temps. Cette perspective lie, dès les premières enquêtes sociologiques, le travail industriel à une interrogation sur les temporalités.The sociology of work and labor developed a particular viewpoint on the analysis of social times. The objective of this article is to show how a criticism of a unique and unifying industrial time progressively grew up. Such criticism leans on three elements: the multiplicity of social times linked to the occupational activity, the disintegrating nature of work in the manufacturing process and the emergence of leisure-time. This point of view was elaborated by the sociology of work in France after 1945, notably by Georges Friedmann, Pierre Naville and William Grossin. Before approaching this period we question the moment of the foundation of sociology. By mobilizing little known research by Max Weber on the manufacturing process, we shall see in what way he was a precursor of the analysis of diversified attitudes regarding time by individuals and groups.

  15. Equipment considerations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Trace or ultratrace analyses require that the HPLC equipment used, including the detector, be optimal for such determinations. HPLC detectors are discussed at length in Chapter 4; discussion here is limited to the rest of the equipment. In general, commercial equipment is adequate for trace analysis; however, as the authors approach ultratrace analysis, it becomes very important to examine the equipment thoroughly and optimize it, where possible. For this reason they will review the equipment commonly used in HPLC and discuss the optimization steps. Detectability in HPLC is influenced by two factors (1): (a) baseline noise or other interferences that lead to errors in assigning the baseline absorbance; (b) peak width. 87 refs

  16. Gas loop - continuous measurement of thermal and fast neutron fluxes; Boucle a gaz - mesure continue de flux de neutrons thermiques et rapides

    Energy Technology Data Exchange (ETDEWEB)

    Droulers, Y; Pleyber, G; Sciers, P; Maurin, G [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1964-07-01

    The measurement method described in this report can be applied both to thermal and fast neutron fluxes. A description is given of two practical applications in each of these two domains. This method is particularly suitable for measurements carried out on 'loop' type equipment. The measurement of the relative flux variations are carried out with an accuracy of 5 per cent. The choice of the shape of the gas circuit leaves a considerable amount of liberty for the adaptation of the measurement circuit to the experimental conditions. (authors) [French] La methode de mesure defrite dans ce rapport s1 applique aussi bien au flux de neutrons thermiques, qu'au flux de neutrons rapides. On donne la description de deux realisations pratiques dans chacun de ces domaines. Cette methode est particulierement adaptee a des mesures effectuees sur des dispositifs du type 'boucle'. La mesure des variations relatives de flux se fait avec une precision de 5 pour cent. Le choix de la configuration du circuit gazeux donne une grande souplesse dans l'adaptation du circuit de mesure aux conditions experimentales. (auteurs)

  17. Thermal cycling behaviour and thermal stability of uranium-molybdenum alloys of low molybdenum content; Comportement au cyclage thermique et stabilite thermique des alliaces uranium-molybdene de faibles teneurs en molybdene

    Energy Technology Data Exchange (ETDEWEB)

    Decours, J; Fabrique, B; Peault, O [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    We have studied the behaviour during thermal cycling of as-cast U-Mo alloys whose molybdenum content varies from 0.5 to 3 per cent; results are given concerning grain stability during extended heat treatments and the effect of treatments combining protracted heating with thermal cycling. The thermal cycling treatments were carried out at 550, 575, 600 and 625 deg C for 1000 cycles; the protracted heating experiments were done at 550, 575, 600 and 625 deg C for 2000 hours (4000 hrs at 625 deg C). The 0.5 per cent alloy resists much better to the thermal cycling than does the non-alloyed uranium. This resistance is, however, much lower than that of alloys containing over l per cent, even at 550 deg C it improves after a heat treatment for grain-refining. Alloys of over 1.1 per cent have a very good resistance to a cycling treatment even at 625 deg C, and this behaviour improves with increasing concentrations up to 3 per cent. An increase in the temperature up to the {gamma}-phase has few disadvantages provided that it is followed by rapid cooling (50 to 100 deg C/min). The {alpha} grain is fine, the {gamma}-phase is of the modular form, and the behaviour during a thermal cycling treatment is satisfactory. If this cooling is slow (15 deg /hr) the {alpha}-grain is coarse and cycling treatment behaviour is identical to that of the 0.5 per cent alloy. The protracted heat treatments showed that the {alpha}-grain exhibits satisfactory stability after 2000 hours at 575, 600 and 625 deg C, and after 4000 hours at 625 deg C. A heat cycling treatment carried out after these tests affects only very little the behaviour of these alloys during cycling. (authors) [French] Nous avons etudie le comportement au cyclage thermique des alliages U-Mo, brut de coulee, dont la teneur varie de 0,5 a 3 pour cent de molybdene, les resultats de stabilite du grain au cours de traitements thermiques de longue duree, ainsi que ceux des traitements combines de longue duree et de cyclage. Les

  18. Influence d'un ecran thermique sur le bilan energetique et le microclimat nocturnes d'une serre

    OpenAIRE

    Baille, M.; Laury, J.C.; Baille, Alain

    1984-01-01

    Dans cet article, on présente les résultats expérimentaux concernant les effets d’un écran thermique sur les déperditions énergétiques et le microclimat nocturnes de deux serres identiques, mais de matériaux de couverture différents : verre horticole ordinaire (V.O.) et verre à faible émissivité (V.F.E.). lorsque l’écran est déployé, on constate une diminution significative des pertes thermiques globales dans les deux serres. L’écran agit surtout au niveau des pertes par convection et par...

  19. Construction of a differential thermal analysis installation; Realisation d'une installation d'analyse thermique differentielle

    Energy Technology Data Exchange (ETDEWEB)

    Branche, G; Chantret, F [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1959-07-01

    The authors are indicating the characteristics of a D.T.A. installation they built. Experimental rooms, ovens, thermal regulation, recording methods are thoroughly described, with outlining of the requirements to obtain a high sensitivity. Numerous D.T.A. curves relating to argillaceous substances, bituminous shales, and uraniferous compounds are given. (author) [French] Les auteurs donnent les caracteristiques de l'installation d'Analyse Thermique Differentielle qu'ils ont construits. Ils decrivent en detail les chambres d'experiences, les fours, la regulation thermique, l'enregistrement, en insistant sur les conditions necessaires pour obtenir une sensibilite elevee. Ils donnent de nombreuses courbes differentielles relatives des produits argileux, des schistes bitumineux et des composes uraniferes. (auteur)

  20. Mesure et modélisation multidimensionnelle des transferts thermiques gaz-paroi dans le cas des moteurs à allumage commandé Measurement and Multidimensional Modeling of Gas-Wall Heat Transfers in Spark-Ignition Engines

    Directory of Open Access Journals (Sweden)

    Gilaber P.

    2006-11-01

    formulation k-epsilon de la turbulence a été adoptée. La sensibilité du modèle aux effets de densité et de turbulence a été testée par l'intermédiaire de variations de l'avance à l'allumage et du régime. La comparaison entre mesure et simulation a montré un bon accord, tant en termes de flux thermiques locaux et instantanés, qu'en termes de bilan global. The computational fluid dynamics codes, which help to predict the behaviour of combusting gas in reciprocating engines, need, as boundary conditions for the momentum and energy equations, to approximate wall frictions and heat transfer between gas and walls. The purpose of this work is to validate a heat transfer model for spark ignited engines. Two steps of research have been worked on to meet this objective: an experimental phase and a computational phase. In the experimental phase, measurements were made on a test-engine instrumented with fast-response surface heat flux gages. Each gage consisted of a steel cylinder, containing two thermocouples. To analyze the influence of fluid dynamics on heat transfer, a Laser Doppler Velocimeter was used, by means of a spacer placed between the engine head and cylinder. The spacer was equiped with two windows and two heat-flux gages permitting simultaneous measurements of the heat flux and of the fluid dynamics outside the boundary layer. Two other gages were present in the head of the engine and up to ten data inputs could be simultaneously recorded at each crank-angle, including two velocity components and the cylinder pressure. A parametric analysis was carried out revealing the following trends:- the global heat transfer rate for a thermodynamic cycle of the engine decreases as the speed of the engine is increased, but the peak value of the wall heat-flux increases because of the increase of the turbulence level. - the volumetric efficiency appeared to have little effect on the turbulence level, and its influence on the heat transfer is mainly due to the increase of

  1. Isolation thermique et acoustique des bâtiments réglementation, produits, mise en oeuvre

    CERN Document Server

    Bureau Veritas

    2015-01-01

    Les impératifs d’efficacité énergétique et de confort acoustique dans les bâtiments entraînent de nouvelles réponses constructives et une évolution considérable des matériaux et procédés d’isolation. Tenant compte des derniers DTU parus, ce guide regroupe dans un même volume l’essentiel des dispositions techniques de mise en oeuvre des systèmes d’isolation thermique et phonique des bâtiments. Ainsi cet ouvrage : • apporte l’éclairage nécessaire à la compréhension des réglementations thermique et acoustique ; • définit les exigences à atteindre concernant l’isolement aux bruits aériens intérieurs et extérieurs, les niveaux de bruits de chocs et d’équipements, ainsi que le traitement acoustique des parties communes ; • détaille les techniques d’isolation des toitures étanchées et des couvertures ; • décrit l’isolation thermique des murs par l’intérieur et par l’extérieur. Ce manuel pratique est destiné aux maîtres d’ouvrage et promoteurs qui y tr...

  2. High power quality for customers; De l'electricite de qualite chez les industriels

    Energy Technology Data Exchange (ETDEWEB)

    Calani, B. [Electricite de France (EDF), 93 - Saint-Denis (France); Tanneau, G. [Electricite de France (EDF), 92 - Clamart (France)

    2000-01-01

    The electrical power quality is a strong criterion for many manufacturers. The improvement of the electrical network and devices has allowed to reach a good power quality level all over the French territory which satisfies the majority of most customer's expectations. However, in some cases, only local desensitization can ne efficient enough to meet the customer's requirement. Emergent equipment based on power electronic devices are evaluated at the Research and Development Division. The aim is to propose the best service offer to our customers on both technical and economical aspects. (authors)

  3. Industrial treatment of solutions of fission products. Separation of caesium-137; Traitement industriel de solutions de produits de fission. Separation du cesium-137

    Energy Technology Data Exchange (ETDEWEB)

    Fisher, C; Raggenbass, A [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1959-07-01

    Two types of chemical treatment can be considered for the manufacture of solid sources for industrial uses from fission product solutions remaining after plutonium extraction: a) concentration of the solution and preparation of solid sources from the bulk material, without separation, b) separation of one or several fission products from which the sources are made. Examination of the radio-chemical composition of the mixture of fission products that will be available from the Marcoule reactors (G1, G2 and G3) shows that caesium-137 accounts for 30 per cent of the {gamma} energy available immediately after the plutonium separation, 70 per cent two years after and 100 per cent after five years. There is practically no advantage in making sources from bulk fission products, since the separation of caesium-137 is no more complicated and yet it results in a material with more potential uses. The separation of caesium-137 by a method based on the standard phospho-tungstate precipitation method has been considered. Previously, the precipitated caesium phospho-tungstate was dissolved and caesium was recovered from the solution by cation-exchange or by removal of phosphate and tungstate ions by anion-exchange. A study has now been made, of the metathesis of caesium phospho-tungstate to barium phosphate and tungstate by the action of barium hydroxide, the caesium being obtained in solution as the hydroxide. The advantages of this new procedure are: - greater decontamination of caesium-137 without further purification, - possibility of direct transformation to caesium sulphate, - general simplification of the procedure and, consequently, of the equipment. (author) [French] Deux types de traitement chimique peuvent etre envisages pour amener a l'etat de sources solides utilisables industriellement les produits de fission contenus dans les solutions residuaires de l'extraction du plutonium. Ces traitements sont les suivants: a) concentration des solutions et confection de

  4. Industrial treatment of solutions of fission products. Separation of caesium-137; Traitement industriel de solutions de produits de fission. Separation du cesium-137

    Energy Technology Data Exchange (ETDEWEB)

    Fisher, C.; Raggenbass, A. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1959-07-01

    Two types of chemical treatment can be considered for the manufacture of solid sources for industrial uses from fission product solutions remaining after plutonium extraction: a) concentration of the solution and preparation of solid sources from the bulk material, without separation, b) separation of one or several fission products from which the sources are made. Examination of the radio-chemical composition of the mixture of fission products that will be available from the Marcoule reactors (G1, G2 and G3) shows that caesium-137 accounts for 30 per cent of the {gamma} energy available immediately after the plutonium separation, 70 per cent two years after and 100 per cent after five years. There is practically no advantage in making sources from bulk fission products, since the separation of caesium-137 is no more complicated and yet it results in a material with more potential uses. The separation of caesium-137 by a method based on the standard phospho-tungstate precipitation method has been considered. Previously, the precipitated caesium phospho-tungstate was dissolved and caesium was recovered from the solution by cation-exchange or by removal of phosphate and tungstate ions by anion-exchange. A study has now been made, of the metathesis of caesium phospho-tungstate to barium phosphate and tungstate by the action of barium hydroxide, the caesium being obtained in solution as the hydroxide. The advantages of this new procedure are: - greater decontamination of caesium-137 without further purification, - possibility of direct transformation to caesium sulphate, - general simplification of the procedure and, consequently, of the equipment. (author) [French] Deux types de traitement chimique peuvent etre envisages pour amener a l'etat de sources solides utilisables industriellement les produits de fission contenus dans les solutions residuaires de l'extraction du plutonium. Ces traitements sont les suivants: a) concentration des solutions et

  5. L’écologie industrielle : quand l’écosystème industriel devient un vecteur du développement durable

    Directory of Open Access Journals (Sweden)

    Arnaud Diemer

    2007-08-01

    Full Text Available L’écologie industrielle, définie par Robert Frosch (1995 comme « l’ensemble des pratiques destinées à réduire la pollution industrielle », nous amène à penser que l’écosystème industriel peut être un véritable vecteur du développement durable. L’ingénierie écologique et l’écotechnologie recommandent aux industriels de procéder à un ensemble d’opérations de rationalisation de la production (optimisation des consommations énergétiques et matérielles, minimisation des déchets à la source,réutilisation des rejets pour servir de matières premières à d’autres processus de production. Les symbioses industrielles et les parcs éco-industriels sont généralement présentés comme des modèles de rationalisation industrielle et des illustrations tangibles du développement durable.Industrial ecology is defined by Robert Frosch (1995 as practices intended to reduce industrial pollution. That leads us to think industrial ecosystem as a vector of sustainable development.Ecological engineering and ecotechnology recommend managers to rationalize the production process (optimization of material consumptions, minimization of bads…. Industrial symbiosis and industrial parks are generally presented as models of industrial rationalization and tangible illustrations of the sustainable development.

  6. La montagne, lieu de développement industriel : l’exemple du Languedoc-Roussillon

    Directory of Open Access Journals (Sweden)

    2007-03-01

    Full Text Available Michel WieninRiches en énergie (rivières, bois, puis houille, en matières premières minérales et en produits d’élevage, les régions de montagne ont développé tôt une industrie qui profite de l’essor des transports au XIXe siècle. Loin des grands bassins miniers, les vallées se transforment en une succession de bourgs industriels, accédant beaucoup plus vite à la modernité que les plaines restées agricoles ou que les villages d’altitude, à l’écart du progrès. Délimité par le Massif Central et les Pyrénées, le Languedoc-Roussillon présente une plaine évoluant vers une quasi-monoculture de la vigne et des vallées de montagne qui se tournent vers l’industrie textile et métallurgique.France’s mountain regions, which are rich in varied sources of energy (rivers, woods, then coal, in mineral resources and in products derived from livestock rearing, developed industries at an early date, benefiting from the development of new transport networks during the 19th century. Far from the major mining basins, the mountain valleys were transformed into a succession of industrial villages, reaching modernity more rapidly than the plains, still devoted to agriculture, or the villages high in the mountains and isolated from such progress. Bordered by the Massif Central and the Pyrenees, the region of Languedoc-Roussillon comprises a plain which evolved towards a mono-activity of wine production and the mountain valleys which witnessed the development of textile and metallurgical industries.

  7. Impact des Propriétés Mécaniques, Géométriques et thermiques des ...

    African Journals Online (AJOL)

    AKA Boko

    Avecε , la déformation, α le coefficient de dilatation thermique, T. ∆ l'écart de température, E, I et A le module d'élasticité, le moment quadratique de la section des éléments substrats et la section des éléments. L'équilibre des moments dans la structure renforcée donne l'équation 13: (). () () ()[. ]a. T. tyyxNxMxM. xM. +. +. +. +.

  8. [Hydrotherapy equipment].

    Science.gov (United States)

    Tsibikov, V B; Ragozin, S I; Mikheeva, L V

    1985-01-01

    A flow-chart is developed demonstrating the relation between medical and prophylactic institutions within the organizational structure of the rehabilitation system and main types of rehabilitation procedures. In order to ascertain the priority in equipping rehabilitation services with adequate hardware the special priority criterion is introduced. The highest priority is assigned to balneotherapeutic and fangotherapeutic services. Based on the operation-by-operation analysis of clinical processes related to service and performance of balneologic procedures the preliminary set of clinical devices designed for baths, basins and showers in hospitals and rehabilitation departments is defined in a generalized form.

  9. L'évolution des combustibles pour moteurs thermiques Evolution of Fuels for Thermal Engines

    Directory of Open Access Journals (Sweden)

    Balaceanu J. C.

    2006-11-01

    Full Text Available Depuis la crise pétrolière, l'accroissement des prix et les craintes de pénurie ont conduit à adapter les moteurs aux combustibles disponibles. Si la situation apparaît comme moins tendue, l'industrie des machines thermiques, qui pendant longtemps a eu comme partenaire une industrie du pétrole très sûre, se trouve cependant confrontée à un marché des combustibles incertain dans son ravitaillement et surtout dans ses prix. Les progrès des moteurs diesel et des turbines à gaz, dûs à une meilleure adaptation à leur usage et aussi à l'évolution de la technologie, supposent que les combustibles n'apporteront aucune contrainte majeure en quantité ou en qualité. La modification des usages dévolus désormais au pétrole entraînera une réduction de la coupe lourde et un raffinage plus profond des bruts avec en particulier un développement du craquage catalytique et de la viscoréduction. Or, ces différentes opérations de conversion peuvent conduire à une détérioration de la qualité des combustibles moins grave pour le gazole que pour le fuel lourd. Dans les différents domaines impliqués, les parades technologiques sont en cours de développement. L'industrie des machines thermiques, qui poursuit l'amélioration des engins, et l'industrie du pétrole, qui recherche une réduction des prix des combustibles, sont donc conduites à un compromis optimal auquel elles ne peuvent accéder efficacement qu'en définissant les règles du jeu c'est-à-dire des spécifications internationales rigoureuses des combustibles. Since the oil crisis, the increase in prices and fears of a shortage have led to the adapting of engines to what fuels are available. Whereas the situation now seems somewhat less tense, the thermal machinery industry, which for a long time had a very reliable petroleum industry as its partner, nonetheless finds itself confronted with an uncertain fuel market with regard to supplies and especially to prices. Progress

  10. TRANSFERT THERMIQUE INSTATIONNAIRE DANS UN MUR TRICOUCHES SUBISSANT UN CHANGEMENT DE PHASE PAR SOLIDIFICATION.

    Directory of Open Access Journals (Sweden)

    O Arfi

    2016-05-01

    Full Text Available Une étude numérique du transfert de chaleur instationnaire dans un mur tricouches est présentée. Le modèle physique est basé sur l’équation de conduction thermique unidirectionnelle en tenant compte des équations de couplages au niveau des interfaces et des conditions convectives de surfaces. Les équations de transfert sont données en représentation enthalpique pour le matériau à changement de phase (MCP, et en formulation générale pour les régions solides. La formulation adimensionnelle a permis de dégager les principaux paramètres affectant le transfert : nombre de Biot (Bi, nombre de Stephan (Ste et le degré de surchauffe (qm. La discrétisation des équations est réalisée en utilisant la méthode des volumes finis selon un schéma explicite. La solution numérique est obtenue par une méthode itérative basée sur la notion d’enthalpie critique. L’étude de l’influence de la condition convective chaude, gouvernée par  Bi¥,cet θ¥,c , a montré que la présence des couches solides affecte la cinétique de la solidification, les limites de la solidification et le transfert de chaleur par un effet de stockage et de déstockage d’énergie sensible. L’influence de la température θ¥,c sur le processus de changement de phase est fortement dépendante du nombre de Biot Bi¥,c.

  11. Magnetic susceptibilities and thermal expansion of artificial graphites; Susceptibilites magnetiques et dilatation thermique des graphites artificiels

    Energy Technology Data Exchange (ETDEWEB)

    Cornuault, P; Herpin, A; Hering, H; Seguin, M [Commissariat a l' Energie Atomique, Paris (France); Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    Starting from measurements of the magnetic susceptibility made in the two principal directions of a graphite bar, the distribution function of the normals to the carbon planes in the crystallites has been evaluated. The effect of different variation in the manufacturing process on this crystalline anisotropy has been studied. From this crystalline anisotropy we have calculated the thermal expansion coefficient possessed by a compact mass of crystallites having exactly the same orientational anisotropy as the porous body consideration. The difference between this and the observed expansion coefficient leads to the determination of the expansion of the non-graphitic part of the mass which turns out to have a negative value and is also anisotropic. We have attempted to draw some conclusions from this result. (author) [French] En partant des mesures de la susceptibilite magnetique faites dans les directions des axes principaux d'un barreau de graphite, on a calcule la fonction de distribution des perpendiculaires aux plans graphitiques dans les cristallites. On a etudie les effets que pouvaient provoquer des modifications dans le procede de fabrication sur l'anisotropie cristalline. En considerant cette anisotropie cristalline, nous avons calcule le coefficient de dilatation thermique pour un bloc compact de cristallites ayant exactement la meme anisotropie d'orientation que le corps poreux en question. La difference entre cette valeur et celle mesuree du coefficient de dilatation, nous permet de calculer la dilatation pour la partie non-graphitique du bloc, en l'occurence, on trouve une valeur negative du coefficient pour cette partie, qui est egalement anisotropique. On a essaye d'en tirer quelques conclusions. (auteur)

  12. Biomass equipments. Dryers. Drying, crushing, agglomeration of agro-industrial products; Materiels pour la biomasse. Les secheurs, sechage, broyage, agglomeration de produits agro-industriels

    Energy Technology Data Exchange (ETDEWEB)

    Deur, O. [Promill (France)

    1997-12-31

    This paper describes the French Promill Company activity in the design and manufacturing of complete drying-crushing-agglomerating units for agro-industrial products (pulp of beet, lucerne, etc..). The paper focusses on the thermal and mechanical efficiency of the high temperature dryer and on the pulp granulating squeezer. (J.S.)

  13. Equipment for biomass. Dryers. Drying, crushing, aggregating of agro-industrial products; Materiels pour la biomasse, les secheurs, sechage, broyage, agglomeration de produits agro-industriels

    Energy Technology Data Exchange (ETDEWEB)

    Deur, O. [Promill, 28 - Serville (France)

    1997-12-31

    The French society Promill has developed complete units for the drying, crushing and aggregating of agro-industrial products (beet roots, agricultural wastes, lucerne, maize, etc.). Drying is conducted in a three-pass drum, using any type of fuel (fuel oil, gas, electric power, coal), and ensuring a thermal yield of 680 kCal/kg and ash emission rates complying with French and European legislation. Granulation is conducted with vapour addition, with a granulate flowrate reaching 15 T/h. Crushing is carried out in a hammer mill

  14. COMPORTEMENT D’UN COMPOSITE FINE MINERALE - CIMENT - BOIS ELABORE A L’AIDE DE DECHETS INDUSTRIELS SOLIDES

    Directory of Open Access Journals (Sweden)

    M.L BENMALEK

    2000-06-01

    Full Text Available Cinq fines minérales de différentes natures minéralogiques et de limites granulaires comparables, provenant de résidus de carrières, ont été traitées pour former le squelette de bétons légers d'isolation. L'allégement et le pouvoir isolant de ces bétons sont obtenus par incorporation de granulats de bois dans la matrice constituée de la fine minérale et de ciment CPA. Dans une première partie, sont présentés les principales caractéristiques de ces fines: minéralogie par diffraction des rayons X, granulométrie laser, conductivité thermique à la sonde TPS, densité sèche par  pycnomètrie à eau et morphologie au MEB. La seconde partie est consacrée à l'étude de l'effet des caractéristiques de ces fines sur le comportement hygrothermique et mécanique de ces bétons élaborés avec une même formulation et un même état de consistance au moulage. Les résultats de ces investigations sont comparés entre eux et  à ceux de matériaux usuels classés par la RILEM.

  15. Contribution to the study of thermal diffusivity of solids; Contribution a l'etude de la diffusivite thermique des solides

    Energy Technology Data Exchange (ETDEWEB)

    Zankel, K [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1967-07-01

    Angstroem method has been reviewed for its application to measurements of thermal diffusivity and conductivity on short specimens. An apparatus and a technique have been developed for rapid and precise measurements of a large variety of materials, which might also contain heat sources. This technique allows measurements at both high and low temperatures. Stainless steel, nickel and uranium monocarbide specimens were tested and the results of the thermal diffusivity measurements between 50 deg. C and 700 deg. C are presented. (author) [French] L'application de la methode d'Angstroem pour la mesure de la diffusivite et de la conductivite thermique sur des echantillons courts est examinee. Un appareillage est decrit, qui permet non seulement des mesures sur une grande variete de materiaux, mais qui est aussi concu pour des mesures rapides, precises et ou des sources thermiques peuvent etre introduites au sein de l'echantillon. La methode s'adapte egalement aux mesures a basses et hautes temperatures. Des resultats de mesure sur un echantillon en acier inoxydable, en nickel et en carbure d'uranium pour des temperatures comprises entre 50 et 700 deg. C sont reportes. (auteur)

  16. Cryogenic equipment

    International Nuclear Information System (INIS)

    Leger, L.; Javellaud, J.; Caro, C.; Gilguy, R.; Testard, O.

    1966-06-01

    The cryostats presented here were built from standard parts; this makes it possible to construct a great variety of apparatus at minimum cost. The liquid nitrogen and helium reservoirs were designed so as to reduce losses to a minimum, and so as to make the cryostats as autonomous as possible. The experimental enclosure which is generally placed in the lower part of the apparatus requires a separate study in every case. Furthermore, complete assemblies such as transfer rods, isolated traps and high vacuum valves, were designed with a similar regard for the economic aspects and for the need for standardization. This equipment thus satisfies a great variety of experimental needs; it is readily adaptable and the consumptions of helium and liquid nitrogen are very low. (authors) [fr

  17. Transferts thermiques dans les bassins sédimentaires Heat Transfers in Sedimentary Basins

    Directory of Open Access Journals (Sweden)

    Perrin J. F.

    2006-11-01

    Full Text Available La connaissance de l'évolution des températures dans les bassins sédimentaires est un instrument utile pour l'exploration pétrolière. En effet, connaissant la cinétique de dégradation chimique, on peut prévoir les rendements de transformation de la matière organique dans un bassin donné. La localisation des roches mères permet ensuite d'évaluer le potentiel pétrolier d'un bassin. L'étude présentée ici traite d'un modèle numérique destiné à prévoir ces champs de température tout au long de l'histoire d'un bassin, le modèle servant aussi pour l'étude des phénomènes de dog-leg thermique. Le modèle prend en compte les transferts par conduction et convection forcée (écoulement de l'eau de compaction et calcule un état des pressions et porosités. II fournit des résultats conformes aux valeurs observées in situ, et permet d'expliquer les anomalies de pressions. Knowing how temperatures have evolved in sedimentary basins is of great importance for petroleum exploration. If the chemical degradation kinetics is known, the transformation yields of organic matter can be forecast in a given basin. Then the location of source rocks can be used to evaluate the petroleum potential of a basin. This article describes a numerical model designed to determine these temperature ranges during the entire history of a basin. The model can also be used to investigate thermal dog-leg phenomena. It takes transfers by conduction and forced convection into consideration (flow of compaction water and calculates pressure and porosity conditions. The results it gives are in good agreement with values observed in situ so that various pressure anomalies can be explained.

  18. Medical Issues: Equipment

    Science.gov (United States)

    ... Information Packets Equipment Pool Living With SMA Medical Issues Palliative Breathing Orthopedics Nutrition Equipment Daily Life At ... curesma.org > support & care > living with sma > medical issues > equipment Equipment Individuals with SMA often require a ...

  19. Semiconductor Manufacturing equipment introduction

    International Nuclear Information System (INIS)

    Im, Jong Sun

    2001-02-01

    This book deals with semiconductor manufacturing equipment. It is comprised of nine chapters, which are manufacturing process of semiconductor device, history of semiconductor manufacturing equipment, kinds and role of semiconductor manufacturing equipment, construction and method of semiconductor manufacturing equipment, introduction of various semiconductor manufacturing equipment, spots of semiconductor manufacturing, technical elements of semiconductor manufacturing equipment, road map of technology of semiconductor manufacturing equipment and semiconductor manufacturing equipment in the 21st century.

  20. Towards a strengthening of inspections carried out on pressurised equipment and pipework..

    International Nuclear Information System (INIS)

    Noel, St.

    2010-01-01

    Following the fast presidential election, a major restructuring of the administrative landscape was set in motion. Tasks that historically were the responsibility of the Ministry of Industry are now carried out by the Ministry of Sustainable Development, which in particular is responsible for the whole policy to do with the prevention of technological risks. The General Directorate for the Prevention of Risks (Direction generale de la prevention des risques (DGPR)) of this ministry is now responsible for controlling technological risks, opening up new perspectives in terms of managing accidental risks and offering a new opportunity for an 'integrated' approach, making it possible to deal with an industrial installation in all its facets. Within the DGPR, the Office for the Safety of Industrial Equipment (bureau de la securite des equipements industriels (BSEI)) is responsible for the safety of pressurised equipment, as well as pipes carrying gas, inflammable liquids and chemical products. After a quick presentation of the inspections carried out on this equipment, issues to do with their safety will be dealt with and in particular: - the suitability of inspections carried out in the tight of faults that are likely to occur and develop in the structures; - control of ageing; - management of the quality of new equipment. (author)

  1. Optimistaion énergétique d'un ensemble industriel Energy Optimization of an Industrial Installation

    Directory of Open Access Journals (Sweden)

    Raimbault C.

    2006-11-01

    Full Text Available Cet article porte sur la mise au point d'une méthode d'optimisation du système de production d'utilités d'un ensemble industriel et l'étude de dispositifs destinés à économiser l'énergie. Le programme d'optimisation fait appel à la programmation linéaire. Un programme générateur de matrice et un programme de traduction des résultats ont été mis au point. On dispose ainsi d'un programme d'optimisation adapté à tout système de production d'utilités. Différents dispositifs permettant d'économiser l'énergie ont été étudiés. L'étude a porté, d'une part, sur des dispositifs classiques tels que les dispositifs de récupération de chaleur sur les fumées et, d'autre part, sur des dispositifs nouveaux. Des solutions nouvelles ont été recherchées dans deux domaines qui sont apparus essentiels : production combinée de travail et de chaleur et valorisation de calories à bas niveau. Enfin la méthode d'optimisation a été appliquée au cas d'une raffinerie réelle dont l'étude avait été effectuée récemment. L'optimisation sur une base économique a permis de dégager une économie de 9,3 % sur la consommation d'énergie, mais a surtout démontré les larges possibilités de la méthode dans son application à un cas concret. This article describes the development of a method for optimizing utilities production systems for on industrial installation and the study of energy-saving systems. The optimization program makes use of linear programming. A matrix-generating program and a result-translating program were developed. The result is an optimization program suited for any utilities production system. Different energy-saving systems were examined, including conventional systems such as heat-recovery devices as well as new systems. New solutions were sought for in two fields which appear essential, i. e. the combined production of work and heat and the valorization of low-level calories. The optimization method was

  2. Master i Industriel Informationsteknologi

    DEFF Research Database (Denmark)

    Knudsen, Morten

    2000-01-01

    Målgruppen for denne åbne Masteruddannelse, som udbydes af Aalborg Universitet i samarbejde med IT-Vest, er personer, som dagligt arbejder med teknisk IT, og som har en videregående uddannelse på bachelorniveau. Uddannelsen, som er 3- årig på ½ tid, startede September 1998, og det samlede optag d...

  3. Master i Industriel Informationsteknologi

    DEFF Research Database (Denmark)

    Knudsen, Morten

    2001-01-01

    Målgruppen for denne åbne Masteruddannelse, som udbydes af Aalborg Universitet i samarbejde med IT-Vest, er personer, som dagligt arbejder med teknisk IT, og som har en videregående uddannelse på bachelorniveau. Uddannelsen, som er 3- årig på ½ tid, startede September 1998, og det samlede optag d...

  4. Industriel patriarkalisme som moderniseringsstrategi

    DEFF Research Database (Denmark)

    Rasmussen, Marianne Rostgård

    2003-01-01

    with hierachical social relations between industrialists and workers, specifying a set of duties and obligations for each of the two parties to meet. Industrialists were, among other things, expected to care for workers who were no longer able to provide for themselves due to illness or old age. The article...... discusses different schemes for taking care of ill and aged workers and shows that such schemes were relatively common around 1900. The discussion focuses on norms and practices, not effects. Whether the schemes actually resulted in lessened social tensions during the transformation to an industrial society...

  5. Contribution to the study of thermal mixing between nuclear spin systems; Contribution a l'etude du melange thermique entre systemes de spins nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Goldmann, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-02-15

    This work describes methods of dynamic nuclear polarization in solids based on the thermal mixing between nuclear spin systems. The description of the thermal mixing processes involves most of the fundamental aspects of the spin temperature theory. The experiments, conducted with paradichlorobenzene and para-dibromobenzene, yield a detailed confirmation of the theoretical predictions. (author) [French] Ce travail decrit des methodes de polarisation dynamique nucleaire dans les solides basees sur le melange thermique entre systemes de spins nucleaires. La description des processus de melange thermique met en jeu la plupart des aspects fondamentaux de la theorie de la temperature de spin. Les experiences, realisees avec du paradichlorobenzene et du paradibromobenzene, apportent une confirmation detaillee des previsions theoriques. (auteur)

  6. Selection of equipment for equipment qualification

    International Nuclear Information System (INIS)

    Torr, K.G.

    1989-01-01

    This report describes the methodology applied in selecting equipment in the special safety systems for equipment qualification in the CANDU 600 MW nuclear generating stations at Gentilly 2 and Point Lepreau. Included is an explanation of the selection procedure adopted and the rationale behind the criteria used in identifying the equipment. The equipment items on the list have been grouped into three priority categories as a planning aid to AECB staff for a review of the qualification status of the special safety systems

  7. Etude de la transition ferroelectrique-ferroelastique du KD2PO4 forme du front de phase en fonction du gradient thermique

    OpenAIRE

    Kvítek, Zdeněk

    2010-01-01

    Etude de la transition ferroelectrique-ferroelastique du KD2PO4 forme du front de phase en fonction du gradient thermique The thesis explores complex process of first order transition of KD2PO4 crystal from tetragonal phase to ferroelectric - ferroelastic orthorhombic phase and back at temperature 209 K. The experimental set up of nitrogeneous cryostat allowes temperature and temperature gradient variations during simultaneous three axes optical sample observations, dielectric measurements. T...

  8. Étude expérimentale des performances thermiques d’un nanofluide: eau-éthylène-glycol-Al2O3

    Directory of Open Access Journals (Sweden)

    Răzvan-Silviu Luciu

    2007-01-01

    Full Text Available Une nouvelle classe de fluides composée par des nanoparticules métalliques en suspension dans un liquide, appelée nanofluide, est apparue récemment. Quelques études numériques et expérimentales ont montré que ces nouveaux fluides possedent une puissance d’échange thermique remarquable, comparée aux liquides conventionnels. L’étude qui suit a le bout de montrer par voie expérimentale les performances thermiques d’un nanofluide composé d’oxyde d’alumine dispersé dans de l’éthylene-glycol en différentes concentrations, allant de 0 a 2%. Le dispositif expérimental est un échangeur a tubes concentriques en inox, avec écoulement du fluide chaud dans le tube central et du fluide froid dans le tube annulaire. Les résultats obtenus montrent que la présence des nanoparticules dans le fluide de base a pour effet une augmentation considérable du transfert thermique.

  9. Relative measurement of the fluxes of thermal, resonant and rapid neutrons in reactor G1; Mesures relatives des flux thermique, resonnant et rapide dans le reacteur G1

    Energy Technology Data Exchange (ETDEWEB)

    Carle, R.; Mazancourt, T. de [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1957-07-01

    We sought to determine the behavior of the thermal, resonant and rapid neutron fluxes in the multiplier-reflector transition region, in the two principal directions of the system. We have also measured the variation of these different fluxes in the body of the multiplier medium in a canal filled with graphite and in an empty canal. The results are given in the form of curves representing: - the variation of the ratio of the thermal flux to the rapid flux in axial and radial transitions - the behavior of the thermal and resonant fluxes and the variation of their ratio in the same regions. (author) [French] Nous avons cherche a determiner le comportement des differents flux, thermique, resonnant et rapide a la transition milieu multiplicateur-reflecteur dans les deux directions principales du reseau. Nous avons egalement mesure la variation de ces differents flux au sein du milieu multiplicateur dans un canal rempli de graphite et dans un canal vide. Les resultats sont donnes sous forme de courbe representant: - La variation du rapport du flux thermique au flux rapide aux transitions axiale et radiale - L'allure des flux thermique et resonnant et la variation de leur rapport dans les memes regions. (auteur)

  10. Status of Enhanced Recovery by Thermal Methods Bilan et orientations de la récupération assistée par méthodes thermiques

    Directory of Open Access Journals (Sweden)

    Burger J.

    2006-11-01

    Full Text Available This paper describes the main developments in thermal methods of oil recovery in recent years. Particular attention is devoted to work aimed at improving understanding of the physical and chemical mechanisms involved and at increasing the efficiency of thermal processes. Their preferred domain of application is described and illustrated by typical cases. The contribution of thermal recovery to oil production in the United States and worldwide is discussed. Cet article décrit les principaux développements des méthodes thermiques de récupération du pétrole au cours des dernières années. L'attention est portée aux travaux visant à la compréhension des mécanismes physiques et chimiques mis en jeu et à accroître l'efficacité des procédés thermiques. Leur domaine d'application est présenté et illustré par des cas types. La contribution de la récupération thermique à la production d'hydrocarbures aux Etats-Unis et dans le monde est discutée.

  11. Relative measurement of the fluxes of thermal, resonant and rapid neutrons in reactor G1; Mesures relatives des flux thermique, resonnant et rapide dans le reacteur G1

    Energy Technology Data Exchange (ETDEWEB)

    Carle, R; Mazancourt, T de [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1957-07-01

    We sought to determine the behavior of the thermal, resonant and rapid neutron fluxes in the multiplier-reflector transition region, in the two principal directions of the system. We have also measured the variation of these different fluxes in the body of the multiplier medium in a canal filled with graphite and in an empty canal. The results are given in the form of curves representing: - the variation of the ratio of the thermal flux to the rapid flux in axial and radial transitions - the behavior of the thermal and resonant fluxes and the variation of their ratio in the same regions. (author) [French] Nous avons cherche a determiner le comportement des differents flux, thermique, resonnant et rapide a la transition milieu multiplicateur-reflecteur dans les deux directions principales du reseau. Nous avons egalement mesure la variation de ces differents flux au sein du milieu multiplicateur dans un canal rempli de graphite et dans un canal vide. Les resultats sont donnes sous forme de courbe representant: - La variation du rapport du flux thermique au flux rapide aux transitions axiale et radiale - L'allure des flux thermique et resonnant et la variation de leur rapport dans les memes regions. (auteur)

  12. Heat transfer in gas-cooled piles; Echanges thermiques dans les piles a gaz

    Energy Technology Data Exchange (ETDEWEB)

    Le Foll, J; Gelin, P; Robert, E de [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    . Technological studies led to such developments as special machining of the caps, using high conductibility metanes, anodic oxidation of thin discs. They provided the basis for solving the problem by removing the more trouble-some heat sources and providing heat insulation of the caps. Experimental study of convection around the fuel rod extremities led then to formulate specific boundary conditions of conduction inside the caps for any given geometry. Conduction in turn was studied by electrical analogy and permitted to map the temperature distribution of the critical region. (author) [French] Des mesures de coefficients d'echange locaux effectuees en regime etabli sur une gaine a ailettes longitudinales montrent que la distribution de ces coefficients le long du contour chauffant d'une section droite presente en general des singularites tres accentuees qui rendent inapplicables les calculs classiques de conduction dans les ailettes. Une etude systematique de cette distribution etablit cependant que deux coefficients numeriques calcules par integration dans le plan de section droite suffisent a rattacher les proprietes thermiques globales a celles d'un canal circulaire de contour isotherme, avec une approximation suffisante dans la plupart des cas. Bien qu'assez delicat, le calcul de ces deux coefficients est rendu accessible par deux analogies rheoelectriques et on peut meme atteindre directement l'influence d'une petite deformation du contour de gaine. Pour une valeur donnee de la temperature limite de gaine, le calcul des performances du canal entier est effectue en considerant que cette limite est effectivement atteinte dans une section droite courante. En pratique, la division du combustible en cartouches courtes risque d'introduire des singularites importantes par rapport a ce cas ideal et le probleme se pose de determiner la forme des extremites de cartouches pour eviter que ces singularites n'affectent les performances. Or, les bouchons qui assurent la fermeture des

  13. Study of thermal effects in superconducting RF cavities; Etude des effets thermiques dans le cavites supraconductrices

    Energy Technology Data Exchange (ETDEWEB)

    Bousson, S.; Caruette, A.; Fouaidy, M.; Hammoudi, N.; Junquera, T.; Lesrel, J.; Yaniche, J.F. [Services Techniques, Inst. de Physique Nucleaire, Paris-11 Univ., 91 - Orsay (France)

    1999-11-01

    A high speed thermometric system equipped with 64 fixed surface thermometers is used to investigate thermal effects in several 3 GHz cavities. An evaluation of the time response of our thermometers is presented. A method based on RF signal analysis is proposed to evaluate the normal zone propagation rate during thermal breakdown. (authors) 2 refs., 3 figs.

  14. Analyse de la dégradation thermique du Poly(éther éther cétone)

    Science.gov (United States)

    Courvoisier, Emilie; Bicaba, Yoann; Colin, Xavier

    2018-03-01

    La dégradation thermique du PEEK a été étudiée à l'état caoutchoutique dans de larges intervalles de température (entre 180 et 320 °C) et de pression partielle d'oxygène (entre 0,21 et 50 bars). Tout d'abord, les mécanismes de vieillissement thermique ont été analysés et élucidés par spectroscopie IRTF et par calorimétrie différentielle (DSC) sur des films de PEEK suffisamment minces (entre 10 et 60 μm d'épaisseur) pour s'affranchir totalement des effets de la diffusion d'oxygène. L'oxydation se produit sur les cycles aromatiques provoquant la croissance de cinq nouvelles bandes d'absorption IR centrées à 3650, 3525, 1780, 1740 et 1718 cm-1 et attribuées aux vibrations d'élongation des liaisons O-H du phénol et de l'acide benzoïque, et des liaisons C-O de l'anhydride benzoïque, du benzoate de phényle et de la fluorénone respectivement. De plus, l'oxydation conduit à une large prédominance de la réticulation sur les coupures de chaîne (augmentation de Tg) empêchant le recuit du PEEK, en particulier lorsque la température d'exposition est supérieure au pied du pic de fusion. Enfin, les conséquences de l'oxydation sur les propriétés élastiques ont été analysées et élucidées par micro-indentation sur des sections droites préalablement polies de plaquettes de PEEK de 3 mm d'épaisseur. Les variations du module d'Young et du taux de cristallinité se corrèlent parfaitement, vérifiant ainsi la relation de Tobolsky.

  15. L'essentiel de la RT 2012 obligations et mise en oeuvre de la réglementation thermique

    CERN Document Server

    Leblond, Philippe

    2004-01-01

    Issue du Grenelle de l’environnement, la réglementation thermique 2012 (RT 2012) a pour objectif de limiter les consommations énergétiques des bâtiments et leurs émissions de gaz à effet de serre. Depuis le 1er janvier 2013, tous les dossiers de permis de construire doivent être conformes aux exigences de résultats et de moyens imposées par la RT 2012. Ils devront indiquer notamment : • la valeur de deux coefficients : Bbiomax, le besoin bioclimatique maximal admissible, et Cepmax, la consommation conventionnelle maximale des bâtiments pour les usages en chauffage, ventilation et refroidissement ; • la valeur de la Ticréf, la température conventionnelle intérieure de référence ; • un certain nombre d’exigences de moyens, comme le respect de la surface et l’ouverture minimales des baies, ou l’obligation d’utiliser les énergies renouvelables. Cet ouvrage didactique et complet décrypte les textes de la RT 2012 et fournit sous forme de guide pratique une méthode simple adaptable ...

  16. Evolution de films de cuivre sur un substrat de cordiérite au cours de traitements thermiques

    Science.gov (United States)

    Guille, Jean-Louis; Gondolf, Marc

    1993-04-01

    Copper films were applied on low sintering temperature cordierite substrates either by sputtering or screen printing. Their behaviour during thermal treatments was studied as a function of various parameters : deposition technique, thickness, firing atmosphere, physical state of the substrate (green or sintered). Films were most often broken during the treatment. In the case of screen printed films the effects of an oxydation-reduction cycle of copper are pointed out. Des films de cuivre ont été déposés sur un substrat de cordiérite à basse température de frittage par deux techniques, pulvérisation cathodique et sérigraphie. On étudie leur comportement au cours de traitements thermiques en fonction de différents paramètres : technique de déposition, épaisseur, atmosphère de traitement, état physique du substrat (cru ou fritté). On constate le plus souvent une fragmentation du film. Dans le cas des films sérigraphiés on met en évidence les effets dus à l'oxydation et à la réduction du cuivre.

  17. Églises et temples en bassins industriels : Belfort-Héricourt-Montbéliard (Franche-Comté (1944-2008

    Directory of Open Access Journals (Sweden)

    Yves-Claude Lequin

    2009-11-01

    Full Text Available Si l’on en juge par l’exemple de Belfort-Montbéliard, nombreux furent les lieux de culte - catholiques et luthériens - construits dans les bassins industriels français entre 1950 et 1968. Étapes : églises modernes « en majesté » vers 1950, églises sobres aux formes arrondies dans les ZUP vers 1960, préfabriqués après 1964, quasi arrêt en 1968, reconversion du bâti à partir de 1990. Raisons de cet essor puissant et du rapide déclin : les tensions sociales et les évolutions mentales des paroissiens.From the example of Belfort-Montbéliard, a fair number of places of worship - Catholic and Lutheran - were built in French industrial basins between 1950 and 1968. Stages: modern “in majesty” churches around 1950, sober buildings with curved shapes in priority development areas around 1960, prefabricated buildings after 1964, hardly any construction in 1968, conversion of buildings as from 1990. Reasons for this marked growth and for the swift decline: social tensions and evolution of parishioners ‘minds.

  18. Aerodynamic and thermal studies of cans of gas cooled fuel elements; Etudes aerodynamiques et thermiques de gaines d'elements combustibles refroidis par gaz

    Energy Technology Data Exchange (ETDEWEB)

    Gelin, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Milliat, J P [Electricite de France (EDF), 75 - Paris (France)

    1964-07-01

    l'amelioration des grappes et s'est ensuite poursuivie dans les deux Laboratoires pour le refroidissement interne des elements combustibles annulaires. Au fur et a mesure de l'avancement de ces etudes, les moyens d'essais se sont amplifies tandis que les methodes experimentales n'ont cesse de s'ameliorer. Actuellement, les deux Laboratoires, qui travaillent en pleine collaboration, disposent de moyens puissants. Pour les grappes, l'effort a surtout porte sur les pertes de charge dues aux pieces d'assemblage et sur les variations de temperature autour des elements de la grappe. On est arrive ainsi a determiner d'une facon satisfaisante les points chauds de gaine, les deformations des crayons et les conditions de stabilite de ces deformations. Pour les gaines a chevrons, les etudes ont porte, d'une part sur l'evolution des performances en fonction des parametres geometriques, et, d'autre part sur les singularites aerodynamiques et thermiques creees tant par les ailettes que par les interruptions de cartouche. Ces etudes ont abouti a une connaissance tres complete des cartouches choisies pour les reacteurs EDF2 et EDF3, et ouvrent maintenant des perspectives tres encourageantes pour les reacteurs a venir, en particulier les reacteurs equipes d'elements annulaires; parmi les solutions convenant a la gaine interne de l'element annulaire, les corrugations et les ailettes longitudinales ont fait l'objet d'essais assez etendus dans une large plage de nombre de Reynolds. (auteurs)

  19. Shipboard and laboratory equipment

    Digital Repository Service at National Institute of Oceanography (India)

    Shyamprasad, M.; Ramaswamy, V.

    The polymetallic nodules occur at an average depth of 4500 m. Adequate equipment and techniques are required for the exploration at such depths. Shipboard and various laboratory equipments for the sampling of polymetallic nodules is described...

  20. Remote handling equipment

    International Nuclear Information System (INIS)

    Clement, G.

    1984-01-01

    After a definition of intervention, problems encountered for working in an adverse environment are briefly analyzed for development of various remote handling equipments. Some examples of existing equipments are given [fr

  1. Exercise Equipment: Neutral Buoyancy

    Science.gov (United States)

    Shackelford, Linda; Valle, Paul

    2016-01-01

    Load Bearing Equipment for Neutral Buoyancy (LBE-NB) is an exercise frame that holds two exercising subjects in position as they apply counter forces to each other for lower extremity and spine loading resistance exercises. Resistance exercise prevents bone loss on ISS, but the ISS equipment is too massive for use in exploration craft. Integrating the human into the load directing, load generating, and motion control functions of the exercise equipment generates safe exercise loads with less equipment mass and volume.

  2. BP volume reduction equipment

    International Nuclear Information System (INIS)

    Kitamura, Yoshinori; Muroo, Yoji; Hamanaka, Isao

    2003-01-01

    A new type of burnable poison (BP) volume reduction system is currently being developed. Many BP rods, a subcomponent of spent fuel assemblies are discharged from nuclear power reactors. This new system reduces the overall volume of BP rods. The main system consists of BP rod cutting equipment, equipment for the recovery of BP cut pieces, and special transport equipment for the cut rods. The equipment is all operated by hydraulic press cylinders in water to reduce operator exposure to radioactivity. (author)

  3. New method of determining the thermal utilization factor of a cell; Nouvelle methode de determination du facteur d'utilisation thermique d'une cellule

    Energy Technology Data Exchange (ETDEWEB)

    Amouyal, A; Benoist, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1956-07-01

    A new formula for the thermal utilization factor is derived, which, while comparable in simplicity to the formula given by elementary diffusion theory, furnishes much more precise results. This is clearly brought out by comparison with the results given by the S{sub n} and spherical harmonics methods. (author) [French] Une nouvelle expression du facteur d'utilisation thermique, d'une simplicite comparable a celle de Ia theorie elementaire, est etablie. La comparaison avec les resultats fournis par la methode S{sub n} et les methodes d'harmoniques spheriques montre que la precision obtenue par cette formule est tres superieure a celle que donne la theorie elementaire. (auteur)

  4. Contribution au développement des moteurs à apport de chaleur externe utilisés pour la conversion des rejets thermiques industriels en électricité. Modélisation et optimisation thermodynamique d’un nouveau convertisseur : Turbosol

    OpenAIRE

    Blaise , Mathilde

    2016-01-01

    To convert the industrial waste heat into mechanical, or electrical energy, is a way to decrease the greenhouse gases emission and the energy consumption. The present PhD thesis is co-financed by the french Environment and Energy Management Agency (ADEME), in this context. The other co-financer, the company Hevatech, exploits the patent of a new heat converter into electricity named Turbosol®. Turbosol® is a good candidate for the industrial waste heat recovery. The concept is currently devel...

  5. Electrical equipment qualification

    International Nuclear Information System (INIS)

    Farmer, W.S.

    1983-01-01

    Electrical equipment qualification research programs being carried out by CEA, JAERI, and Sandia Laboratories are discussed. Objectives of the program are: (1) assessment of accident simulation methods for electrical equipment qualification testing; lower coarse (2) evaluation of equipment aging and accelerated aging methods; (3) determine radiation dose spectrum to electrical equipment and assess simulation methods for qualification; (4) identify inadequacies in electrical equipment qualification procedures and standards and potential failure modes; and (5) provide data for verifying and improving standards, rules and regulatory guides

  6. Space Heating Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Rafferty, Kevin D.

    1998-01-01

    The performance evaluation of space heating equipment for a geothermal application is generally considered from either of two perspectives: (a) selecting equipment for installation in new construction, or (b) evaluating the performance and retrofit requirements of an existing system. With regard to new construction, the procedure is relatively straightforward. Once the heating requirements are determined, the process need only involve the selection of appropriately sized hot water heating equipment based on the available water temperature. It is important to remember that space heating equipment for geothermal applications is the same equipment used in non-geothermal applications. What makes geothermal applications unique is that the equipment is generally applied at temperatures and flow rates that depart significantly from traditional heating system design. This chapter presents general considerations for the performance of heating equipment at non-standard temperature and flow conditions, retrofit of existing systems, and aspects of domestic hot water heating.

  7. EFFET DES TRAITEMENTS THERMIQUES SUR LA REACTION ENTRE DES COUCHES MINCES DE TITANE ET DES SUBSTRATS EN ACIER

    Directory of Open Access Journals (Sweden)

    D Slimani

    2015-06-01

    Full Text Available Des couches minces du titane pur ont été déposées avec la méthode de pulvérisation cathodique sur des substrats en acier, type FF80 K-1 contenants ~1% mass. en carbone. La réaction entre les deux parties du système substrat-couche mince est activée avec des traitements thermiques sous vide dans l’intervalle de températures de 400 à900°Cpendant 30 minutes. Les Spectres de diffraction de rayons x confirment l’inter- diffusion des éléments  chimiques du système résultants la formation et la croissance des nouvelles phases en particulier le carbure binaire TiC ayant des caractéristiques thermomécaniques importantes. L’analyse morphologique des échantillons traités  avec le microscope électronique à balayage (MEB montre l’augmentation du flux de diffusion atomique avec la température de recuit, notamment la diffusion du manganèse et du fer vers la surface libre des échantillons aux températures élevées provoquant la dégradation des propriétés mécaniques des revêtements contrairement au premiers stades d’interaction où on a obtenu des bonnes valeurs de la microdureté.

  8. Thermal neutron flux measurements using neutron-electron converters; Mesure de flux de neutrons thermiques avec des convertisseurs neutrons electrons

    Energy Technology Data Exchange (ETDEWEB)

    Le Meur, R; Lecomte, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-07-01

    The operation of neutron-electron converters designed for measuring thermal neutron fluxes is examined. The principle is to produce short lived isotopes emitting beta particles, by activation, and to measure their activity not by extracting them from the reactor, but directly in the reactor using the emitted electrons to deflect the needle of a galvanometer placed outside the flux. After a theoretical study, the results of the measurements are presented; particular attention is paid to a new type of converter characterized by a layer structure. The converters are very useful for obtaining flux distributions with more than 10{sup 7} neutrons cm{sup -2}*sec{sup -1}. They work satisfactorily in pressurized carbon dioxide at 400 Celsius degrees. Some points still have to be cleared up however concerning interfering currents in the detectors and the behaviour of the dielectrics under irradiation. (authors) [French] On examine le fonctionnement de convertisseurs neutrons electrons destines a des mesures de flux de neutrons thermiques. Le principe est de former par activation des isotopes a periodes courtes et a emission beta et de mesurer leur activite non pas en les sortant du reacteur, mais directement en pile, utilisant les electrons emis pour faire devier l'aiguille d'un galvanometre place hors flux. Apres une etude theorique, on indique des resultats de mesures obtenus, en insistant particulierement sur un nouveau type de convertisseur, caracterise par sa structure stratifiee. Les convertisseurs sont tres interessants pour tracer, des cartes de flux a partir de 10{sup 7} neutrons cm{sup -2}*s{sup -1}. Ils sont utilisables pour des flux de 10{sup 14} neutrons cm{sup -2}*s{sup -1}. Ils fonctionnent correctement dans du gaz carbonique sous pression a 400 C. Des points restent cependant a eclaircir concernant les courants parasites dans les detecteurs et le comportement des dielectriques pendant leur irradiation. (auteur)

  9. Renewal of radiological equipment.

    Science.gov (United States)

    2014-10-01

    In this century, medical imaging is at the heart of medical practice. Besides providing fast and accurate diagnosis, advances in radiology equipment offer new and previously non-existing options for treatment guidance with quite low morbidity, resulting in the improvement of health outcomes and quality of life for the patients. Although rapid technological development created new medical imaging modalities and methods, the same progress speed resulted in accelerated technical and functional obsolescence of the same medical imaging equipment, consequently creating a need for renewal. Older equipment has a high risk of failures and breakdowns, which might cause delays in diagnosis and treatment of the patient, and safety problems both for the patient and the medical staff. The European Society of Radiology is promoting the use of up-to-date equipment, especially in the context of the EuroSafe Imaging Campaign, as the use of up-to-date equipment will improve quality and safety in medical imaging. Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or renewal. This plan should look forward a minimum of 5 years, with annual updates. Teaching points • Radiological equipment has a definite life cycle span, resulting in unavoidable breakdown and decrease or loss of image quality which renders equipment useless after a certain time period.• Equipment older than 10 years is no longer state-of-the art equipment and replacement is essential. Operating costs of older equipment will be high when compared with new equipment, and sometimes maintenance will be impossible if no spare parts are available.• Older equipment has a high risk of failure and breakdown, causing delays in diagnosis and treatment of the patient and safety problems both for the patient and the medical staff.• Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or replacement. This plan should look forward a

  10. Contribution to the study of thermal diffusivity of solids; Contribution a l'etude de la diffusivite thermique des solides

    Energy Technology Data Exchange (ETDEWEB)

    Zankel, K. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1967-07-01

    Angstroem method has been reviewed for its application to measurements of thermal diffusivity and conductivity on short specimens. An apparatus and a technique have been developed for rapid and precise measurements of a large variety of materials, which might also contain heat sources. This technique allows measurements at both high and low temperatures. Stainless steel, nickel and uranium monocarbide specimens were tested and the results of the thermal diffusivity measurements between 50 deg. C and 700 deg. C are presented. (author) [French] L'application de la methode d'Angstroem pour la mesure de la diffusivite et de la conductivite thermique sur des echantillons courts est examinee. Un appareillage est decrit, qui permet non seulement des mesures sur une grande variete de materiaux, mais qui est aussi concu pour des mesures rapides, precises et ou des sources thermiques peuvent etre introduites au sein de l'echantillon. La methode s'adapte egalement aux mesures a basses et hautes temperatures. Des resultats de mesure sur un echantillon en acier inoxydable, en nickel et en carbure d'uranium pour des temperatures comprises entre 50 et 700 deg. C sont reportes. (auteur)

  11. Measurement of the diffusion length of thermal neutrons in the beryllium oxide; Mesure de la longueur de diffusion des neutrons thermiques dans l'oxyde de beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Koechlin, J C; Martelly, J; Duggal, V P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    The diffusion length of thermal neutrons in the beryllium oxide has been obtained while studying the spatial distribution of the neutrons in a massive parallelepiped of this matter placed before the thermal column of the reactor core of Saclay. The mean density of the beryllium oxide (BeO) is 2,95 gr/cm{sup 3}, the mean density of the massif is 2,92 gr/cm{sup 3}. The value of the diffusion length, deducted of the done measures, is: L = 32,7 {+-} 0,5 cm (likely gap). Some remarks are formulated about the influence of the spectral distribution of the neutrons flux used. (authors) [French] La longueur de diffusion des neutrons thermiques dans l'oxyde de beryllium a ete obtenue en etudiant la repartition spatiale des neutrons dans un massif parallelepipedique de cette matiere placee devant la colonne thermique de la Pile de Saclay. La densite moyenne de l'oxyde de beryllium (BeO) est de 2,95 gr/cm{sup 3}, la densite moyenne du massif de 2,92 gr/cm{sup 3}. La valeur de la longueur de diffusion, deduite des mesures effectuees est: L 32,7 {+-} 0,5 cm (ecart probable). Des remarques sont formulees quant a l'influence de la repartition spectrale du flux de neutrons utilise. (auteurs)

  12. Methods for determining thermal stresses values. Some examples relating to nuclear reactors; Methodes de determination des contraintes thermiques. Quelques exemples d'application aux reacteurs

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, J; Gautier, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Peres, A [Israel Institute of Technology, Dept. of Nuclear Science Technion (Israel)

    1958-07-01

    As modern techniques develop more elaborate machines, and make their way towards higher and higher temperatures and pressures, the thermal stresses become a matter of major importance in the design of mechanical structures. In the first part of this paper, the authors examine the problem from a theoretical standpoint, and try to evaluate the aptitude and limitation of mathematical techniques to attain the quantitative values of thermal stresses. This paper deals mainly with the experimental methods to measure thermal stresses. The authors show some examples relating to nuclear reactors. (author)Fren. [French] Au fur et a mesure que la technique moderne developpe des machines plus poussees et s'oriente vers des temperatures et des pressions toujours plus elevees, les contraintes thermiques deviennent un facteur d'importance capitale dans le calcul des structures mecaniques. Les auteurs examinent d'abord l'aspect theorique du probleme, ainsi que l'aptitude et les limites du calcul pour exprimer quantitativement la valeur des contraintes thermiques. Les auteurs exposent principalement, ensuite, les methodes experimentales qui permettent de mesurer ces contraintes, et illustrent cet expose de quelques exemples relatifs aux installations nucleaires. (auteur)

  13. Measurement of the thermal utilisation factor of the reactor G1; Mesure du facteur d'utilisation thermique du reacteur G1

    Energy Technology Data Exchange (ETDEWEB)

    Roullier, F; Schmitt, A P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1957-07-01

    The thermal utilisation factor of the lattice of the reactor G1 has been measured by applying the autoradiographic technique to thin detectors irradiated in the cell. The experimental apparatus is described, and the results compared with those obtained by calculation based on various formulae. The results of the study of the thermal flux distribution in a cell containing a thorium rod of the same diameter as the uranium rods in the lattice are also given. The precision of the measurements is discussed. Value found: f diameter 26 = 0.8949 {+-} 0,005. (author) [French] Le facteur d'utilisation thermique du reseau du reacteur G1 a ete mesure en appliquant la technique de l'autoradiographie a des detecteurs minces irradies dans la cellule. Les dispositifs experimentaux sont decrits et les resultats sont compares a ceux obtenus par le calcul a partir de diverses formules. Les resultats de l'etude de la distribution du flux thermique dans une cellule contenant une barre de thorium de meme diametre que les barres d'uranium du reseau sont egalement indiques. La precision des mesures est discutee. Valeur trouvee: f diametre 26 = 0,8949 {+-} 0,005. (author)

  14. Integration of industrial risk in regional policy management. Possibilities of evaluation; L'integration du risque industriel dans les politiques de gestion territoriales. Possibilites d'evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Hubert, Philippe; Pages, Pierre

    1990-02-01

    Since the responsibility for risk management depends more and more on regional factors, evaluation methods and management regulations are not developed enough. This study start from the fact that an important methods exist for evaluation transport of dangerous materials in cities, risk analysis and emergency plans related to classified installations, management of quality of water, 'chronic' industrial risks at local and regional level, probabilistic estimation for industrial plants. The objective is in fact to show what risk analysis could bring to the municipality, the city or the region. [French] Alors que la responsabilite de la maitrise du risque repose de plus en plus sur les collectivites territoriales, soit dans la mouvance naturelle de la decentralisation, soit par des textes specifiques, les moyens d'evaluation et les regles de gestion sont encore tres peu developpes. Cette etude part du fait qu'un materiel important existe cependant: evaluations sur le transport des matieres dangereuses dans les villes, etudes de danger et plans d'intervention associes a la legislation sur les installations classees, gestion de la qualite de l'eau par les agences de bassin, bilans des risques industriels 'chroniques' a l'echelle locale ou regionale, evaluations probabilistes sur des objets industriels. L'objet est donc de montrer ce que peuvent apporter ces analyses dans l'evaluation du risque accidentel dans la collectivite, la ville ou, a cause des implications des strategies de prevention, le departement ou la region. L'heterogeneite de la qualite et de la quantite des resultats que l'on peut attendre en fonction des divers types de risques et de consequences est d'abord mise en valeur. Malgre leurs incertitudes, des modeles existent qui permettent de calculer les victimes d'accidents industriels 'types'. Pour les installations classees et les transports de matieres dangereuses, le calcul du risque est loin d'etre systematique, mais il est pratique. Un second domaine

  15. Modelisation de champs de puits geothermiques en serie pour un stockage thermique saisonnier

    Science.gov (United States)

    Lecomte, Corentin

    This thesis presents a study of the methods for modeling boreholes in series used for seasonal borehole thermal energy storage, along with a description and verification of an analytical model suited for large bore fields (≥ 100 boreholes). A detailed study of existing models for seasonal borehole thermal energy storage using in-series bore fields is performed beforehand, to identify modeling needs. A model entitled NBiS (Network of Borehole in Series) is presented in this thesis. As a first step, the model is studied for a simple configuration involving two boreholes each equipped with a single U-tube, linked in a single network (NBiS(2) model). Then, the model is adapted to a case where the number of boreholes nB is set by the user. Finally, the last version of the model (NBiS(4) model) is suited for nB 4-tubes boreholes piped to form two independent circuits. It also allows the user a mixed configuration with parallel branches of in-series boreholes. Each of the three versions of the NBiS model has been implemented as a Type in the TRNSYS environment. These models have been successfully verified using inter-model comparisons. Lastly, an example of annual simulations for a solar community is presented, where the seasonal borehole thermal energy storage is modeled using a TRNSYS Type of the NBiS suite of models.

  16. RETRIEVAL EQUIPMENT DESCRIPTIONS

    International Nuclear Information System (INIS)

    J. Steinhoff

    1997-01-01

    The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) retrieval from the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. There are no quality assurance requirements or QA controls in this document. Retrieval under normal conditions is accomplished with the same fleet of equipment as is used for emplacement. Descriptions of equipment used for retrieval under normal conditions is found in Emplacement Equipment Descriptions, DI: BCAF00000-01717-5705-00002 (a document in progress). Equipment used for retrieval under abnormal conditions is addressed in this document and consists of the following: (1) Inclined Plane Hauler; (2) Bottom Lift Transporter; (3) Load Haul Dump (LHD) Loader; (4) Heavy Duty Forklift for Emplacement Drifts; (5) Covered Shuttle Car; (6) Multipurpose Vehicle; and (7) Scaler

  17. Medical equipment management

    CERN Document Server

    Willson, Keith; Tabakov, Slavik

    2013-01-01

    Know What to Expect When Managing Medical Equipment and Healthcare Technology in Your Organization As medical technology in clinical care becomes more complex, clinical professionals and support staff must know how to keep patients safe and equipment working in the clinical environment. Accessible to all healthcare professionals and managers, Medical Equipment Management presents an integrated approach to managing medical equipment in healthcare organizations. The book explains the underlying principles and requirements and raises awareness of what needs to be done and what questions to ask. I

  18. Data communication equipment

    International Nuclear Information System (INIS)

    Kim, Hak Seon; Lee, Sang Mok

    1998-02-01

    The contents of this book are introduction of data communication on definition, purpose and history, information terminal about data communication system and data transmission system, data transmit equipment of summary, transmission cable, data port, concentrator and front-end processor, audio communication equipment like phones, radio communication equipment of summary on foundation of electromagnetic waves, AM transmitter, AM receiver, FM receiver and FM transmitter, a satellite and mobile communication equipment such as earth station, TT and C and Cellular phone, video telephone and new media apparatus.

  19. Addressing safety issues through a joint industry programme; Traiter des problemes de securite a travers un programme industriel commun

    Energy Technology Data Exchange (ETDEWEB)

    Pool, G.; Williams, T.P. [BG Technology (United Kingdom); Jones, A.M. [Health and Safety Executive (United Kingdom)

    2000-07-01

    In an increasingly fragmented gas market, the focus for national gas safety may not rest with one major utility or gas supplier but may be spread across many companies. There will also be many new organisations in a liberalized gas industry with varying views on the needs and benefits of safety related technology development but all agree there is a need to ensure that the good safety record of gas as a domestic fuel is maintained. The number of carbon monoxide (CO) incidents is not decreasing significantly despite an increased awareness of the problem. As a consequence, a two-year joint industry programme addressing issues related to carbon monoxide has been established, co-ordinated by BG Technology and supported by gas organisations, government agencies, manufacturers and suppliers across Europe and the World. The 2-year 2 pound million programme has been constructed as twelve separate projects addressing issues such as the reporting and analysis of domestic incidents, improved service or installation practice, CO alarm reliability and information dissemination. The paper gives results and achievements of the programme, through new techniques, standards, procedures or equipment and demonstrates how the gas industry can work together to meet common safety objectives. (authors)

  20. Cooling of electronic equipment

    DEFF Research Database (Denmark)

    A. Kristensen, Anders Schmidt

    2003-01-01

    Cooling of electronic equipment is studied. The design size of electronic equipment decrease causing the thermal density to increase. This affect the cooling which can cause for example failures of critical components due to overheating or thermal induced stresses. Initially a pin fin heat sink...

  1. Capital Equipment Replacement Decisions

    OpenAIRE

    Batterham, Robert L.; Fraser, K.I.

    1995-01-01

    This paper reviews the literature on the optimal replacement of capital equipment, especially farm machinery. It also considers the influence of taxation and capital rationing on replacement decisions. It concludes that special taxation provisions such as accelerated depreciation and investment allowances are unlikely to greatly influence farmers' capital equipment replacement decisions in Australia.

  2. Experimental methods of reactor physics; Methodes experimentales de physique des reacteurs a neutrons thermiques

    Energy Technology Data Exchange (ETDEWEB)

    Breton, D; Lafore, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    This paper is a synthesis of various experimental methods in use with the reactors of the Commissariat a l'Energie Atomique. The main techniques used are mentioned and the difficulties encountered and the accuracy obtained are particularly dwelt upon. The application of these various methods to reactors in order to obtain specific results is also indicated. This paper consists of five parts. I - General methods. Macroscopic and microscopic flux distribution (anisotropy effect), power distribution, etc... II - Kinetic measurements a) pulsed neutron technique: apparatus and accuracy; application to {lambda}t and to anti reactivity measurements; application to graphite, light water and beryllium oxide. b) oscillation techniques: equipment and accuracy; application to the measurements of effective cross sections and resonance integrals. c) fluctuations: apparatus and technique of measurement. III - Poison methods. Description of methods for introducing and extracting the poison, difficulties encountered with light and heavy water, measurement of temperature coefficients and anti-reactivity. IV - Spectra measurements. Choice and development of foils, problems of measurement, application to spectral measurements for thermalization studies, application to dosimetry. V - Experimental shielding measurements. The technique and apparatus recently developed in this field are presented. (authors) [French] Cette communication fait une synthese des differentes methodes experimentales mises en oeuvre sur les reacteurs du CEA. Elle presente les principales techniques utilisees et insiste plus particulierement sur les difficultes rencontrees et la precision obtenue; elle indique egalement l'application de ces differentes methodes sur les reacteurs, en vue de l'obtention des resultats determines. Elle comporte cinq parties: I - METHODES GENERALES: Distribution de flux macroscopique et microscopique (effet d'anisotropie), distribution de puissance, etc... II - MESURES CINETIQUES: a

  3. An apparatus for differential thermal analysis (1961); Realisation d'un appareil d'analyse thermique differentielle (1961)

    Energy Technology Data Exchange (ETDEWEB)

    Rappeneau, J; Quetier, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-07-01

    An apparatus for differential thermal analysis has been developed for the study of the energy stored in irradiated graphite. It makes possible the measurement of variations in the differential enthalpy d H / d{theta} of irradiated graphite between room temperature and 800 deg. C. The integration of the results gives values for the total energy H({theta}). The temperature measurements are made with an accuracy of 0,1 deg. C and are reproducible to {+-} 0,2 deg. C. The characteristics of the apparatus are such that it is possible to study, as a function of irradiation conditions (doses, temperatures), the evolution of the energy spectrum of the graphite as well as the modifications of this spectrum brought about by annealing and successive irradiations, by slow annealing, or by annealing under irradiation. The apparatus developed can also be used for the study of metals and alloys (transition temperatures and heats of transformation), in particular uranium and uranium alloys. (authors) [French] Un appareil d'analyse thermique differentielle a ete realise pour etudier l'energie emmagasinee par le graphite irradie. Il permet de determiner la variation de l'enthalpie differentielle dH / d{theta} du graphite irradie entre la temperature ambiante et 800 deg. C. L'integration des resultats obtenus fournit les valeurs de l'energie totale H({theta}). Les mesures de temperature sont effectuees avec une sensibilite de 0,1 deg. C et la reproductibilite des mesures est assuree a {+-} 0,2 deg. C. Les caracteristiques de cet appareil sont suffisantes pour permettre d'etudier en fonction des conditions d'irradiation (doses, temperatures) l'evolution du spectre d'energie du graphite ainsi que les modifications de ce spectre par des recuits et des irradiations successives, par des recuits lents, ou par des recuits sous rayonnement. Par ailleurs, l'appareil mis au point peut etre utilise pour etudier les metaux et alliages (temperatures de transition et chaleurs de transformation), en

  4. Modélisation d'un choc thermique doux d'un verre S.S.C en utilisant l'approche thermomécanique

    Science.gov (United States)

    Malou, Z.; Hamidouche, M.; Madjoubi, M. A.; Bousbaa, C.; Bouaouadja, N.

    2005-05-01

    Dans ce travail, nous avons étudié l'endommagement du verre silico-sodo-calcique (trois différentes épaisseurs : 2mm, 4mm, et 8mm) par choc thermique descendant. Nous avons utilisé l'approche thermomécanique en terme de facteur d'intensité de contrainte en se basant sur un calcul numérique. Le choc thermique descendant, est la mise en contact brutal d'un échantillon, préalablement chauffé à une température Ti, avec un milieu dont la température Tf est inférieure à Ti. Le gradient thermique engendré induit des contraintes de tension dans les couches superficielles du corps. Ces contraintes peuvent conduire à la rupture du matériau. Les hypothèses prises en compte lors de la simulation sont comme suit : Le refroidissement des échantillons en verre chauffés à différentes températures, inférieures à sa température de transition, est fait par jet d'air à 20° C pendant 6 secondes. Ce temps est suffisant pour que la température des échantillons atteigne l'ambiante. Le coefficient de transfert de chaleur est de 600 W/°C.m2. Les températures chaudes ont été variées entre 100° C et 450° C. Lors des calculs, nous avons intégré, l'évolutions en fonction de la température des propriétés thermoélastiques du verre. Dans un premier temps, nous avons déterminé les températures et les contraintes transitoires dans l'échantillon à tout instant du choc thermique. Ensuite, nous avons déterminé l'évolution du facteur d'intensité de contrainte (FIC) durant le refroidissement. Enfin, les FIC calculés sont comparés à la ténacité (K1c) du matériau. Cette dernière a été mesurée en utilisant la mécanique linéaire de la rupture. Nous avons vérifié que quand le facteur FIC atteint la valeur de la ténacité dans la zone des défauts critiques, ces derniers se propagent d'une manière brutale causant ainsi la dégradation de l'échantillon. Par cette technique, nous avons directement accès à l'écart de température critique

  5. Operational measurements in radioprotection in the industrial and medical environments; Mesures operationnelles en radioprotection dans les milieux industriel et medical

    Energy Technology Data Exchange (ETDEWEB)

    Rodde, S.; Vial, Th.; Truffert, H.; Kramar, R.; Batalla, A.; Roine, Ph.; Pin, A.; Lahaye, Th.; Rodde, S.; Bordy, J.M.; Paquet, F.; Veres, A.; Cadiou, A.; Branthonne, J.Y.; Noel, A.; Laloubere, L.; Moreau, St.; Gensdarmes, F.; Marques, S.; Lestang, M.; Valendru, N.; Tranchant, Ph.; Martel, P.; Bernhard, S.; Chareyre, P.; Gardin, I.; Casanova, Ph.; De Vita, A.; Tenailleau, L.; Masson, B.; Feret, B.; Guerin, M.; Guillot, L.; Gaultier, E.

    2009-07-01

    operational measurement to the committed dose (P. Casanova); 24 - technical control of environments in basic nuclear facilities (A. De Vita); 25 - measurements of the atmospheric tritium with low volume activity level in nuclear facilities (PREVAIR system) (L. Tenailleau); 26 - measurement of high-energy pulsed neutrons (B. Masson); 27 - dismantling: from in-situ measurement to final package characterization (B. Feret); 28 - new generation of detection and identification equipments (M. Guerin); 29 - DIRAD{sup TM} - radionuclides detection and identification - system of automatic detection and identification of moving radioactive objects (L. Guillot); 30 - ViewPoint - radioprotection supervision post (E. Gaultier). (J.S.)

  6. Tests on dynamic corrosion by water. Influence of the passage of a heat flux on the corrosion kinetics. pH measurement in water at high temperature; Essais de corrosion dynamique par l'eau. Influence du passage d'un flux thermique sur la cinetique de corrosion. Mesure du pH dans l'eau a haute temperature

    Energy Technology Data Exchange (ETDEWEB)

    Coriou, H.; Grall, L.; Hure, J.; Saint-James, R. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Berthod [Societe Grenobloise d' Etudes et d' Applications Hydrauliques, 38 (France); Le peintre [Centre National de la Recherche Scientifique (CNRS), 38 - Grenoble (France)

    1958-07-01

    The passage of a heat flux through the surface of a metal placed in a corrosive medium influences the rate of corrosion, these being higher than under adiabatic conditions. The apparatus developed for corrosion tests is described, it is possible to obtain with this equipment: 1) Heat fluxes greater than 200 W/cm{sup 2}, across aluminium canning, which is cooled by water (temperature 50 deg. C), circulating with flow rates of the order of 5 to 6 m/s. 2) Heat fluxes which can go up to 150 W/cm{sup 2}, across canning of zircaloy or stainless steel. The cooling fluid is pressurized water at a temperature around 280 deg. C, the flow-rate of circulation reaching 6 m/s. The results obtained on aluminium canning are studied from the viewpoint of corrosion, paying particular attention to cavitation phenomena which can cause serious damage in certain special circumstances. After developing a glass electrode system capable of supporting high pressures, the authors have investigated materials capable of functioning as a hydrogen electrode and of resisting satisfactorily corrosion by water at 200 deg. C. Various possibilities have been examined: electrodes of special glasses, quartz, metals, with a membrane etc... The results of the various tests and the practical limits of utilisation are given. (author)Fren. [French] Le passage d'un flux thermique a travers la surface d'un metal place dans un milieu corrosif influence les vitesses de corrosion, celles-ci etant plus elevees que dans des conditions adiabatiques. On decrit les appareils mis au point, pour essais de corrosion. Ils permettent d'obtenir: 1) A travers des gaine aluminium des flux thermiques depassant 200 W /cm{sup 2}. Les gaines sont refroidies par l'eau (temperature 50 deg. C), circulant a des vitesses de l'ordre de 5 a 6 m/s. 2) A travers des gaines en zircaloy ou acier inoxydable des flux thermiques pouvant s'elever a 150 W/cm{sup 2}. Le fluide de refroidissement est de l

  7. Tests on dynamic corrosion by water. Influence of the passage of a heat flux on the corrosion kinetics. pH measurement in water at high temperature; Essais de corrosion dynamique par l'eau. Influence du passage d'un flux thermique sur la cinetique de corrosion. Mesure du pH dans l'eau a haute temperature

    Energy Technology Data Exchange (ETDEWEB)

    Coriou, H; Grall, L; Hure, J; Saint-James, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Berthod, [Societe Grenobloise d' Etudes et d' Applications Hydrauliques, 38 (France); peintre, Le [Centre National de la Recherche Scientifique (CNRS), 38 - Grenoble (France)

    1958-07-01

    The passage of a heat flux through the surface of a metal placed in a corrosive medium influences the rate of corrosion, these being higher than under adiabatic conditions. The apparatus developed for corrosion tests is described, it is possible to obtain with this equipment: 1) Heat fluxes greater than 200 W/cm{sup 2}, across aluminium canning, which is cooled by water (temperature 50 deg. C), circulating with flow rates of the order of 5 to 6 m/s. 2) Heat fluxes which can go up to 150 W/cm{sup 2}, across canning of zircaloy or stainless steel. The cooling fluid is pressurized water at a temperature around 280 deg. C, the flow-rate of circulation reaching 6 m/s. The results obtained on aluminium canning are studied from the viewpoint of corrosion, paying particular attention to cavitation phenomena which can cause serious damage in certain special circumstances. After developing a glass electrode system capable of supporting high pressures, the authors have investigated materials capable of functioning as a hydrogen electrode and of resisting satisfactorily corrosion by water at 200 deg. C. Various possibilities have been examined: electrodes of special glasses, quartz, metals, with a membrane etc... The results of the various tests and the practical limits of utilisation are given. (author)Fren. [French] Le passage d'un flux thermique a travers la surface d'un metal place dans un milieu corrosif influence les vitesses de corrosion, celles-ci etant plus elevees que dans des conditions adiabatiques. On decrit les appareils mis au point, pour essais de corrosion. Ils permettent d'obtenir: 1) A travers des gaine aluminium des flux thermiques depassant 200 W /cm{sup 2}. Les gaines sont refroidies par l'eau (temperature 50 deg. C), circulant a des vitesses de l'ordre de 5 a 6 m/s. 2) A travers des gaines en zircaloy ou acier inoxydable des flux thermiques pouvant s'elever a 150 W/cm{sup 2}. Le fluide de refroidissement est de l'eau sous pression a une temperature

  8. HVAC systems and equipment

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, S.T. (Linford Air and Refrigeration Company, Oakland, CA (US))

    1990-02-01

    The author discusses the section of the ASHRAE Standard 90.1-1989 which addresses HVAC systems and equipment. New features of HVAC systems mandatory general requirements are described. New prescriptive requirements are detailed.

  9. Personal Protective Equipment

    National Research Council Canada - National Science Library

    1998-01-01

    ... of personal protective equipment A safety program for new employees is a necessary part of any orientation program An on-going safety program should be used to motivate employees to continue to use...

  10. Electronic equipment packaging technology

    CERN Document Server

    Ginsberg, Gerald L

    1992-01-01

    The last twenty years have seen major advances in the electronics industry. Perhaps the most significant aspect of these advances has been the significant role that electronic equipment plays in almost all product markets. Even though electronic equipment is used in a broad base of applications, many future applications have yet to be conceived. This versatility of electron­ ics has been brought about primarily by the significant advances that have been made in integrated circuit technology. The electronic product user is rarely aware of the integrated circuits within the equipment. However, the user is often very aware of the size, weight, mod­ ularity, maintainability, aesthetics, and human interface features of the product. In fact, these are aspects of the products that often are instrumental in deter­ mining its success or failure in the marketplace. Optimizing these and other product features is the primary role of Electronic Equipment Packaging Technology. As the electronics industry continues to pr...

  11. CV equipment responsibilities

    CERN Document Server

    Pirollet, B

    2008-01-01

    This document describes the limits of the responsibilities of the TS/CV for fire fighting equipment at the LHC. The various interfaces, providers and users of the water supply systems and clean water raising systems are described.

  12. Equipment for hydraulic testing

    International Nuclear Information System (INIS)

    Jacobsson, L.; Norlander, H.

    1981-07-01

    Hydraulic testing in boreholes is one major task of the hydrogeological program in the Stripa Project. A new testing equipment for this purpose was constructed. It consists of a downhole part and a surface part. The downhole part consists of two packers enclosing two test-sections when inflated; one between the packers and one between the bottom packer and the bottom of the borehole. A probe for downhole electronics is also included in the downhole equipment together with electrical cable and nylon tubing. In order to perform shut-in and pulse tests with high accuracy a surface controlled downhole valve was constructed. The surface equipment consists of the data acquisition system, transducer amplifier and surface gauges. In the report detailed descriptions of each component in the whole testing equipment are given. (Auth.)

  13. Development of an apparatus for measuring the thermal conductivity of irradiated or non-irradiated graphite; Realisation d'un appareil de mesure de la conductibilite thermique du graphite irradie ou non irradie

    Energy Technology Data Exchange (ETDEWEB)

    Bocquet, M; Micaud, G

    1962-07-01

    An apparatus was developed for measuring the thermal conductivity coefficient K of irradiated or non-irradiated graphite. The measurement of K at around room temperature with an accuracy of about 6% is possible. The study specimen is placed in a vacuum between a hot and a cold source which create a temperature gradient {delta}{theta}/ {delta}x in the steady state. The amount of heat transferred, Q, is deduced from the electrical power dissipated at the hot source, after allowing for heat losses. The thermal conductivity coefficient is defined as: K = Q/S. {delta}x/{delta}{theta}, S being the cross section of the sample. Systematic studies have made it possible to determine the mean values of the thermal conductivity. (authors) [French] Un appareil de mesure du coefficient de conductibilite thermique K du graphite irradie ou non irradie a ete realise. Utilisant le principe du transfert de chaleur, il permet de mesurer K au voisinage de la temperature ambiante avec une precision de 6 pour cent environ. L'echantillon de graphite etudie est place sous vide entre une source chaude et une source froide qui creent en regime permanent un gradient de temperature {delta}{theta}/{delta}x La quantite de chaleur transferee Q est deduite de la puissance electrique dissipee dans la source chaude en deduisant les pertes thermiques. Le coefficient de conductibilite thermique est defini par: K = Q/S. {delta}x/{delta}{theta} S designant la section de l'echantillon. Des etudes systematiques ont permis de determiner pour differents graphites non irradies les valeurs moyennes des coefficients de conductibilite thermique. Ces etudes ont mis en evidence pour un type de graphite donne, l'influence de la densite apparente sur le coefficient de conductibilite thermique. A partir de mesures effectuees sur des echantillons de graphite irradies preleves par carottage dans les empilements des reacteurs a moderateur de graphite les variations du rapport K0/Ki en fonction de la dose et de la

  14. Analyse de l'emballement thermique d'un système chimique hybride non tempéré

    OpenAIRE

    Véchot , Luc; Bigot , Jean-Pierre; Minko , Wilfried ,; Kazmierczak , Marc; Vicot , Patricia

    2009-01-01

    National audience; Ce travail s'intéresse au “blow-down” (emballement thermique en présence d'un évent de sécurité) d'un système chimique non tempéré (30% CHP) soumis à un incendie. Il utilise une maquette à l'échelle 0,1 l. L'analyse des données post décomposition a montré que la vapeur présente est principalement un produit de la réaction. Toutes les expériences de blow-down ont présenté deux pics de pression, quel que soit le rapport A/V, ce qui est typique des systèmes non tempérés. Nous ...

  15. Measurement of a thermal neutron flux using air activation; Mesure de flux de neutrons thermiques par activation d'air

    Energy Technology Data Exchange (ETDEWEB)

    Guyonvarh, M; Lecomte, P; Le Meur, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-07-01

    It is necessary to know, in irradiation loops, the thermal neutron flux after the irradiation device has been introduced and without being obliged to wait for the discharge of this device. In order to measure the flux and to control it continuously, one possible method is to place in the flux a coiled steel tube through which air passes. By measuring the activity of argon 41, and with a knowledge of the flow rate and the temperature of the air, it is possible to calculate the flux. An air-circulation flux controller is described and the relationship between the flux and the count rate is established The accuracy of an absolute measurement is about 14 per cent; that of a relative measurement is about 3 per cent. The measurement can be carried out equally well whether the reactor is operating at maximum or at low power. The measurement range goes from 10{sup 9} to lO{sup 15} n.cm{sup -2}.sec{sup -1}, and it would be possible after a few modifications to measure fluxes between 10{sup 5} and 10{sup 15} n.cm{sup -2}.sec{sup -1}. Finally, the method is very safe to operate: there is little risk of irradiation because of the low specific activity of the argon-41 formed, and no risk of contamination because the decay product of argon-41 is stable. This method, which is now being used in loops, is thus very practical. (authors) [French] Sur des boucles d'irradiation il est necessaire de connaitre le flux de neutrons thermiques apres mise en place du dispositif d'irradiation et sans etre oblige d'attendre le detournement de ce dispositif. Pour mesurer le flux et le controler en permanence, une methode consiste a placer sous flux un serpentin en acier dans lequel on fait circuler de l'air. La mesure d'activite d'argon 41 permet de calculer le flux, connaissant le debit et la temperature de l'air. Un controleur de flux par circulation d'air est decrit et la relation entre le flux et le taux de comptage est etablie. La precision d'une mesure absolue est de l'ordre de 14 pour

  16. Equipment abnormality monitoring device

    International Nuclear Information System (INIS)

    Ando, Yasumasa

    1991-01-01

    When an operator hears sounds in a plantsite, the operator compares normal sounds of equipment which he previously heard and remembered with sounds he actually hears, to judge if they are normal or abnormal. According to the method, there is a worry that abnormal conditions can not be appropriately judged in a case where the number of objective equipments is increased and in a case that the sounds are changed gradually slightly. Then, the device of the present invention comprises a plurality of monitors for monitoring the operation sound of equipments, a recording/reproducing device for recording and reproducing the signals, a selection device for selecting the reproducing signals among the recorded signals, an acoustic device for converting the signals to sounds, a switching device for switching the signals to be transmitted to the acoustic device between to signals of the monitor and the recording/reproducing signals. The abnormality of the equipments can be determined easily by comparing the sounds representing the operation conditions of equipments for controlling the plant operation and the sounds recorded in their normal conditions. (N.H.)

  17. Prioritizing equipment for replacement.

    Science.gov (United States)

    Capuano, Mike

    2010-01-01

    It is suggested that clinical engineers take the lead in formulating evaluation processes to recommend equipment replacement. Their skill, knowledge, and experience, combined with access to equipment databases, make them a logical choice. Based on ideas from Fennigkoh's scheme, elements such as age, vendor support, accumulated maintenance cost, and function/risk were used.6 Other more subjective criteria such as cost benefits and efficacy of newer technology were not used. The element of downtime was also omitted due to the data element not being available. The resulting Periop Master Equipment List and its rationale was presented to the Perioperative Services Program Council. They deemed the criteria to be robust and provided overwhelming acceptance of the list. It was quickly put to use to estimate required capital funding, justify items already thought to need replacement, and identify high-priority ranked items for replacement. Incorporating prioritization criteria into an existing equipment database would be ideal. Some commercially available systems do have the basic elements of this. Maintaining replacement data can be labor-intensive regardless of the method used. There is usually little time to perform the tasks necessary for prioritizing equipment. However, where appropriate, a clinical engineering department might be able to conduct such an exercise as shown in the following case study.

  18. Radioactive decontamination of equipment

    International Nuclear Information System (INIS)

    1982-03-01

    After a recall of some definitions relating to decontamination techniques and of the regulation into effect, the principles to be respected to arrange rationally work zones are quoted while insisting more particularly on the types of coatings which facilitate maintenance operations and the dismantling of these installations. Then, the processes and equipments to use in decontamination units for routine or particular operations are described; the list of recommended chemical products to decontaminate the equipment is given. The influence of these treatments on the state and the duration of life of equipments is studied, and some perfectible methods are quoted. In the appendix, are given: the limits of surface contamination accepted in the centers; a standard project which defines the criteria of admissible residual contamination in wastes considered as cold wastes; some remarks on the interest that certain special ventilation and air curtain devices for the protection of operators working on apparatus generating contaminated dusts [fr

  19. Equipment Operational Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Greenwalt, B; Henderer, B; Hibbard, W; Mercer, M

    2009-06-11

    The Iraq Department of Border Enforcement is rich in personnel, but poor in equipment. An effective border control system must include detection, discrimination, decision, tracking and interdiction, capture, identification, and disposition. An equipment solution that addresses only a part of this will not succeed, likewise equipment by itself is not the answer without considering the personnel and how they would employ the equipment. The solution should take advantage of the existing in-place system and address all of the critical functions. The solutions are envisioned as being implemented in a phased manner, where Solution 1 is followed by Solution 2 and eventually by Solution 3. This allows adequate time for training and gaining operational experience for successively more complex equipment. Detailed descriptions of the components follow the solution descriptions. Solution 1 - This solution is based on changes to CONOPs, and does not have a technology component. It consists of observers at the forts and annexes, forward patrols along the swamp edge, in depth patrols approximately 10 kilometers inland from the swamp, and checkpoints on major roads. Solution 2 - This solution adds a ground sensor array to the Solution 1 system. Solution 3 - This solution is based around installing a radar/video camera system on each fort. It employs the CONOPS from Solution 1, but uses minimal ground sensors deployed only in areas with poor radar/video camera coverage (such as canals and streams shielded by vegetation), or by roads covered by radar but outside the range of the radar associated cameras. This document provides broad operational requirements for major equipment components along with sufficient operational details to allow the technical community to identify potential hardware candidates. Continuing analysis will develop quantities required and more detailed tactics, techniques, and procedures.

  20. Charging equipment. Ladegeraet

    Energy Technology Data Exchange (ETDEWEB)

    Neumann, E

    1981-09-17

    The invention refers to a charging equipment, particularly on board charging equipment for charging traction batteries of an electric vehicle from the AC mains supply, consisting of a DC converter, which contains a controlled power transistor, a switching off unloading circuit and a power transmitter, where the secondary winding is connected in series with a rectifier diode, and a smoothing capacitor is connected in parallel with this series circuit. A converter module is provided, which consists of two DC voltage converters, whose power transistors are controlled by a control circuit in opposition with a phase displacement of 180/sup 0/.

  1. Experimental equipment, ch. 6

    International Nuclear Information System (INIS)

    Boomstra, F.; Hoogenboom, A.M.; Prins, C.M.; Strasters, B.A.; Vermeer, A.; Wit, P. de; Zwol, N.A. van.

    1977-01-01

    The experimental equipment in use at Utrecht university is discussed. Attention is paid to the tandem Van de Graaff accelerator and the 4MV and 1MV accelerators. The detection systems for gamma-ray spectroscopy are reviewed with emphasis on the compton-suppression spectrometer. The data-handling system used for experiments with the tandem is also briefly discussed

  2. Equipment gift to Monaco

    International Nuclear Information System (INIS)

    1970-01-01

    Research work at the Agency's Laboratory of Marine Radioactivity in Monaco, including that concerned with pollution of the sea, has been made more effective by its latest acquisition of equipment. This is a spectrophotometer donated by the Federal Republic of Germany. (author)

  3. Lifetime of Mechanical Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Leland, K.

    1999-07-01

    The gas plant at Kaarstoe was built as part of the Statpipe gas transport system and went on stream in 1985. In 1993 another line was routed from the Sleipner field to carry condensate, and the plant was extended accordingly. Today heavy additional supply- and export lines are under construction, and the plant is extended more than ever. The main role of the factory is to separate the raw gas into commercial products and to pump or ship it to the markets. The site covers a large number of well-known mechanical equipment. This presentation deals with piping, mechanical and structural disciplines. The lifetime of mechanical equipment is often difficult to predict as it depends on many factors, and the subject is complex. Mechanical equipment has been kept in-house, which provides detailed knowledge of the stages from a new to a 14 years old plant. The production regularity has always been very high, as required. The standard of the equipment is well kept, support systems are efficient, and human improvisation is extremely valuable.

  4. Safeguards techniques and equipment

    International Nuclear Information System (INIS)

    1997-01-01

    The current booklet is intended to give a full and balanced description of the techniques and equipment used for both nuclear material accountancy and containment and surveillance measures, and for the new safeguards measure of environmental sampling. As new verification measures continue to be developed, the material in the booklet will be periodically reviewed and updated versions issued. (author)

  5. Equipping tomorrow's fire manager

    Science.gov (United States)

    Christopher A. Dicus

    2008-01-01

    Fire managers are challenged with an ever-increasing array of both responsibilities and critics. As in the past, fire managers must master the elements of fire behavior and ecology using the latest technologies. In addition, today’s managers must be equipped with the skills necessary to understand and liaise with a burgeoning group of vocal stakeholders while also...

  6. Electrical equipment design library

    International Nuclear Information System (INIS)

    1994-01-01

    This book guides the design supervision, construction order for electrical equipment. The contents of this library are let's use electricity like this, leading-in-pole and casual power, electric pole install below 300KVA, electric pole install below 301∼1000KVA, electric pole install exceed 1000KVA, rooftop install exceed 1000KVA, CUBICLE type, 154KV services. It adds an appendix.

  7. Orphee reactor experimental equipment

    International Nuclear Information System (INIS)

    1987-01-01

    Experimental equipment around the ORPHEE reactor is presented. The neutron source; and the spectrometers and sample environment (inelastic and quasi-elastic scattering, elastic scattering, spread scattering, small angle scattering) are described. An experiment proposal and reports guide is supplied [fr

  8. Seismic qualification of equipment

    International Nuclear Information System (INIS)

    Heidebrecht, A.C.; Tso, W.K.

    1983-03-01

    This report describes the results of an investigation into the seismic qualification of equipment located in CANDU nuclear power plants. It is particularly concerned with the evaluation of current seismic qualification requirements, the development of a suitable methodology for the seismic qualification of safety systems, and the evaluation of seismic qualification analysis and testing procedures

  9. Underground coal equipment

    Energy Technology Data Exchange (ETDEWEB)

    Chadwick, J.

    2002-12-01

    This paper reports on increasing automation and enhanced productivity on longwalls, new development cutting and bolting technologies and haulage systems. Amongst equipment discussed is DBT's Electra series EL3000 shearer, the Dosco LH1400 roadheader with onboard bolters, and Joy 12 CM30 continuous miners. 4 photos.

  10. Global Industriel E-handel

    DEFF Research Database (Denmark)

    Rask, Morten

    Afhandlingen undersøger danske industrivirksomheders transformationsproces på vej mod en ny æra, hvor Internettet anvendes som et centralt redskab i samhandelen med andre virksomheder, og hvor virksomhedens konkurrenceevne og globaliseringsproces styrkes som følge af anvendelsen. Formålet med afh...

  11. Visual communication and terminal equipment

    International Nuclear Information System (INIS)

    Kang, Cheol Hui

    1988-06-01

    This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.

  12. Visual communication and terminal equipment

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Cheol Hui

    1988-06-15

    This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.

  13. Equipment cost optimization

    International Nuclear Information System (INIS)

    Ribeiro, E.M.; Farias, M.A.; Dreyer, S.R.B.

    1995-01-01

    Considering the importance of the cost of material and equipment in the overall cost profile of an oil company, which in the case of Petrobras, represents approximately 23% of the total operational cost or 10% of the sales, an organization for the optimization of such costs has been established within Petrobras. Programs are developed aiming at: optimization of life-cycle cost of material and equipment; optimization of industrial processes costs through material development. This paper describes the methodology used in the management of the development programs and presents some examples of concluded and ongoing programs, which are conducted in permanent cooperation with suppliers, technical laboratories and research institutions and have been showing relevant results

  14. X-ray equipment

    International Nuclear Information System (INIS)

    Redmayne, I.G.B.

    1988-01-01

    The patent concerns a warning and protection system for mobile x-ray equipment used for 'on site' radiography, so that workers in the vicinity of such a working unit can be alerted to its presence. The invention is a local repeater warning system which gives a preliminary warning that energisation of the tubehead is imminent, as well as a switch near the tubehead to abort or inhibit energisation. The latter switch allows personnel caught in the vicinity of the tubehead to prevent energisation. The preliminary warning may be flashing lamps or by a klaxon. The control unit for the equipment may include a monitoring circuit to detect failure of the warning light or klaxon. (U.K.)

  15. X-ray equipment

    Energy Technology Data Exchange (ETDEWEB)

    Redmayne, I.G.B.

    1988-01-06

    The patent concerns a warning and protection system for mobile x-ray equipment used for 'on site' radiography, so that workers in the vicinity of such a working unit can be alerted to its presence. The invention is a local repeater warning system which gives a preliminary warning that energisation of the tubehead is imminent, as well as a switch near the tubehead to abort or inhibit energisation. The latter switch allows personnel caught in the vicinity of the tubehead to prevent energisation. The preliminary warning may be flashing lamps or by a klaxon. The control unit for the equipment may include a monitoring circuit to detect failure of the warning light or klaxon. (U.K.).

  16. Tube for irradiation equipment

    International Nuclear Information System (INIS)

    Goehrich, K.; Vogt, H.

    1979-01-01

    This patent describes a tube for irradiation equipment for limiting an emergent beam, with a baseplate, possessing a central aperture, intended for attaching to the equipment, as well as four carrier plates, each of which possesses a limiting edge and a sliding edge located at right angles thereto. The carrier plates are located parallel to the baseplate, the limiting edge of each carrier plate resting against the sliding edge of the adjacent carrier plate and each of the two mutually opposite pairs of carrier plates being displaceable, parallel to the direction of its sliding edges and symmetrically to the center of the transmission aperture, for the purpose of continuously varying the transmission aperture defined by the limiting edges, during which displacement each of the displaced carrier plates carries with it the carrier plate, resting against the limiting edge of the former plate, parallel to the direction of the limiting edge of the latter plate. 8 claims

  17. Equipment for isotope diagnostics

    International Nuclear Information System (INIS)

    Platz, W.

    1976-01-01

    The invention concerns an improvement of equipment for isotope diagnostics allowing to mark special intensity ranges of the recorded measurements by means of different colors. For undisturbed operation it is of advantage to avoid electric circuits between movable and unmovable parts of the color recorder. According to the invention, long gear wheels of glass fiber-reinforced polyamide are used for these connections. (ORU) [de

  18. Soviet equipment flies in

    CERN Multimedia

    CERN PhotoLab

    1978-01-01

    End of February 1977 a Soviet Ilyushin-76 heavy freight aircraft landed at Cointrin airport having on board fifty large wire proprtional chambers and associated apparatus, together weighing 10 tons, supplied by the Joint Institute for Nuclear Research, Dubna, USSR. The equipment was for the CERN- Dubna-Munich-Saclay experiment NA4 on deep inelastic muon scattering being set up in the North Area of SPS. See Weekly Bulletin 11/78.

  19. Labelling of equipment dispensers.

    Science.gov (United States)

    Gray, D C

    1993-01-01

    A new labelling system for use on medical equipment dispensers is tested. This system uses one of the objects stored in each unit of the dispenser as the 'label', by attaching it to the front of the dispenser with tape. The new system was compared to conventional written labelling by timing subjects asked to select items from two dispensers. The new system was 27% quicker than the conventional system. Images Fig. 1 PMID:8110335

  20. Equipment Obsolescence Management Program

    Energy Technology Data Exchange (ETDEWEB)

    Redmond, J.

    2014-07-01

    Nuclear Power Plant (NPP) Operators are challenged with securing reliable supply channels for safety related equipment due to equipment obsolescence. Many Original Equipment Manufacturers (OEMs) have terminated production of spare parts and product life-cycle support. The average component life cycles are much shorter than the NPP design life, which means that replacement components and parts for the original NPP systems are not available for the complete design life of the NPPs. The lack or scarcity of replacement parts adversely affects plant reliability and ultimately the profitability of the affected NPPs. This problem is further compounded when NPPs pursue license renewal and approval for plant-life extension. A reliable and predictable supply of replacement co components is necessary for NPPs to remain economically competitive and meet regulatory requirements and guidelines. Electrical and I and C components, in particular, have short product life cycles and obsolescence issues must be managed pro actively and not reactively in order to mitigate the risk to the NPP to ensure reliable and economic NPP operation. (Author)

  1. Personal protective equipment

    International Nuclear Information System (INIS)

    2004-01-01

    This Practical Radiation Technical Manual is one of a series that has been designed to provide guidance on radiological protection for employers, radiation protection officers, managers and other technically competent persons who have responsibility for ensuring the safety of employees working with ionizing radiation. The Manual may be used with the appropriate IAEA Practical Radiation Safety Manuals to provide training, instruction and information for all employees engaged in work with ionizing radiation. Personal protective equipment (PPE) includes clothing or other special equipment that is issued to individual workers to provide protection against actual or potential exposure to ionizing radiations. It is used to protect each worker against the prevailing risk of external or internal exposure in circumstances in which it is not reasonably practicable to provide complete protection by means of engineering controls or administrative methods. Adequate personal protection depends on PPE being correctly selected, fitted and maintained. Appropriate training for the users and arrangements to monitor usage are also necessary to ensure that PPE provides the intended degree of protection effectively. This Manual explains the principal types of PPE, including protective clothing and respiratory protective equipment (RPE). Examples of working procedures are also described to indicate how PPE should be used within a safe system of work. The Manual will be of most benefit if it forms part of a more comprehensive training programme or is supplemented by the advice of a qualified expert in radiation protection. Some of the RPE described in this Manual should be used under the guidance of a qualified expert

  2. Study of deformation mechanisms of zinc bicrystals by thermal cycling (1963); Etude des mecanismes de deformation par cyclage thermique de bicristaux de zinc (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Mondon, J [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1963-06-15

    The thermal cycling of zinc bicrystals has been studied in order to precise the thermal cycling growth mechanism, proposed by Burke and TURKALO, specially the dependence of 'equi-cohesive' temperature of grains on their mutual orientation and the parameters of the thermal cycle. Dilatometric studies showed that a bicrystal had no equi-cohesive temperature and that the grain-boundary develops stress at all temperatures. The creep of single and bicrystal have been studied on a dilatometer with stress below the Yield-stress. At constant temperature secondary creep appears after a transient period, at cycled temperature creep stays transient for strains of about 10{sup -4} to 10{sup -3} when the crystal is plastically hard. Micrographic investigations show that grain-boundary migration accompanies the grain boundary shearing and that cycles produce a strong polygonisation, corroborating the fact that the grain boundary remains a stress-generator and that creep occurs in the volume of grains. The discussion of results shows that the transient creep of hard grain in a bicrystal makes the thermal cycling irreversible and allows on elongation at each cycle if that have the lower expansion coefficient. (author) [French] Le cyclage thermique de bicristaux de zinc a ete etudie pour preciser le mecanisme de la croissance au cyclage thermique propose par BURKE et TURKALO, notamment la temperature d' 'equicohesion' des grains en fonction de leur orientation mutuelle et du regime de cyclage impose. Des essais dilatometriques ont montre qu'un bicristal ne presentait pas de temperature d'equicohesion et que le joint exercait des contraintes quelle que soit la temperature superieure du cycle. Le fluage de monocristaux et de bicristaux a ete etudie sur un dilatometre avec des contraintes inferieures a la limite elastique. A temperature constante le fluage secondaire apparait apres une periode transitoire, a temperature cyclee le fluage reste transitoire pour des deformations de l

  3. État des connaissances sur le traitement thermique des produits lourds State of the Art of the Thermal Treatment of Heavy Products

    Directory of Open Access Journals (Sweden)

    Blouri B.

    2006-11-01

    Full Text Available Après rappel du traitement thermique des hydrocarbures comme un moyen de viscoréduction des charges lourdes, craquage en oléfines gazeuses, ou pyrolyse totale en gaz de synthèse, le mécanisme réactionnel de vapocraquage des produits lourds constitue la première partie de l'article. Le craquage des huiles lourdes s'effectue selon un mécanisme radicalaire, tandis que les dépôts de carbone sont formés par des réactions de cycloadditions et polycondensations à des températures moyennes et par l'intermédiaire des radicaux à haute température. L'étude expérimentale du craquage thermique du n-tétracosane, du méthyl-6 eicosane et du dodécylbenzène constitue la deuxième partie de l'article et elle met en évidence, grâce à un mécanisme réactionnel du type moléculaire, la possibilité de craquage contrôlé d'une isoparaffine ou d'un hydrocarbure aromatique lourd en hydrocarbure liquide plus léger. After reviewing the thermal treatment of hydrocarbons as a way of visbreaking heavy feedstock, cracking them into gaseous olefins, or totally pyrolyzing them into synthetic gas, the first part of this article describes the reac-tion mechanism of the steam cracking of heavy products. Heavy oils are cracked by a radical mechanism, while carbon deposits are formed by cycloaddition and polycondensation reactions at mean temperatures and by the intermediary of radicals at high temperature. An experimental investigation of the thermal cracking of n-tetracosane, 6-methyleicosane and dodecylbenzene makes up the second part of the article. A reaction mechanism of the molecular type is used to describe the possibility of the controlled cracking of an isoparaffin or of a heavy aromatic hydrocarbon into a lighter liquid hydrocarbon.

  4. Le néo-corporatisme réinterpellé : analyse comparée de deux politiques d'accès à l'emploi, l'apprentissage industriel en Belgique et le contrat de qualification "jeunes" en France

    OpenAIRE

    Levêque, Audrey

    2006-01-01

    The comparative study of the "apprentissage industriel" in French speaking Belgium and of the "contrat de qualification jeunes" in France shows the maintenance of the neo corporatist model of social State. The analysis of the emergence and of the implementation of these two employment public policies for low qualified young permit to understand how they are appropriated on the ground, especially in the metallurgy sector. If these policies are intended for those low qualified young, the implem...

  5. Scientific Equipment Division - Overview

    International Nuclear Information System (INIS)

    Halik, J.

    2001-01-01

    Full text: The Scientific Equipment Division consists of the Design Group and the Mechanical Workshop. The activity of the Division includes the following: - designing of devices and equipment for experiments in physics, their mechanical construction and assembly. In particular, there are vacuum chambers and installations for HV and UHV; - maintenance and upgrading of the existing installations and equipment in our Institute; - participation of our engineers and technicians in design works, equipment assembly and maintenance for experiments in foreign laboratories. The Design Group is equipped with PC-computers and AutoCAD graphic software (release 2000 and Mechanical Desktop 4.0) and a AO plotter, what allows us to make drawings and 2- and 3-dimensional mechanical documentation to the world standards. The Mechanical Workshop can offer a wide range of machining and treatment methods with satisfactory tolerances and surface quality. It offers the following possibilities: - turning - cylindrical elements of a length up to 2000 mm and a diameter up to 400 mm, and also disc-type elements of a diameter up to 600 mm and a length not exceeding 300 mm; - milling - elements of length up to 1000 mm and gear wheels of diameter up to 300 mm; - grinding - flat surfaces of dimensions up to 300 mm x 1000 mm and cylindrical elements of a diameter up to 200 mm and a length up to 800 mm; - drilling - holes of a diameter up to 50 mm; - welding - electrical and gas welding, including TIG vacuum-tight welding; - soft and hard soldering; - mechanical works including precision engineering; - plastics treatment - machining and polishing using diamond milling, modelling, lamination of various shapes and materials, including plexiglas, scintillators and light-guides; - painting - paint spraying with possibility of using furnace-fred drier of internal dimensions of 800 mm x 800 mm x 800 mm. Our workshop posses CNC milling machine which can be used for machining of work-pieces up to 500 kg

  6. The development of a pilot industrial irradiation facility; Realisation d'une station d'irradiation {gamma} a caractere 'semi-industriel'

    Energy Technology Data Exchange (ETDEWEB)

    Balestic, F; Leveque, P; Prevost, C; Comte, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Saclay, utilisee pour le stockage des barres d'uranium apres leur defournement, a ete specialement amenagee pour permettre des irradiations sur des quantites semi-industrielles de produits chimiques et alimentaires. Des calculs de flux {gamma} ont montre qu'il etait possible de realiser des sources intenses et d'irradier de grands volumes avec des arrangements particuliers de barres dans la casemate. L'installation comporte ainsi deux parties ou different la repartition des barres et les dispositifs d'irradiation. Dans une premiere chambre betonnee et climatisee, 9 rangees verticales de barres d'uranium et de canaux a irradiation alternent avec un ecartement minimum de fa n a constituer un assemblage compact. Le diametre des canaux varie de 10 a 20 cm et la hauteur de chargement utile, 70 cm, correspond a la zone sensiblement uniforme du rayonnement. Dans une deuxieme chambre maintenue a -7 deg. C, des balancelles (h: 70 cm, Q: 35 cm) guidees par un monorail circulent autour d'une seule rangee de 20 barres. La carte des flux y a l'interieur de la casemate a ete etablie par une methode de calcul deja utilisee pour les barres de la pile EL2 a Saclay. Le champ du rayonnement varie dans le temps principalement au cours des premiers mois apres le defournement et suivant le motif geo etrique adopte pour les barres. Les intensites d onisation theoriques sont comprises entre dix mille et plusieurs millions de roentgens par heure. Ces valeurs sont comparees aux resultats obtenus avec les dosimetres chimiques au sulfate ferreux et a l'acide oxalique. En outre, des verreseurs etalonnes avec des sources de cobalt permettent un controle rapide de la dose delivree aux balancelles du convoyeur durant leur parcours dans la chambre froide. La casemate de desactivation de EL3 constitue de par sa capacite de traitement la premiere realisation en France d'une station d'irradiation {gamma} a caractere semi-industriel effectuee avec le concours des services du Commissariat a l

  7. Mining face equipment

    Energy Technology Data Exchange (ETDEWEB)

    G, Litvinskiy G; Babyuk, G V; Yakovenko, V A

    1981-01-07

    Mining face equipment includes drilling advance wells, drilling using explosives on the contour bore holes, loading and transporting the crushed mass, drilling reinforcement shafts, injecting reinforcement compounds and moving the timber. Camouflet explosives are used to form relaxed rock stress beyond the mining area to decrease costs of reinforcing the mining area by using nonstressed rock in the advance well as support. The strengthening solution is injected through advanced cementing wells before drilling the contour bores as well as through radial cementing wells beyond the timbers following loading and transport of the mining debris. The advance well is 50-80 m.

  8. Coal ash monitoring equipment

    Energy Technology Data Exchange (ETDEWEB)

    Clayton, C G; Wormald, M R

    1978-10-02

    The monitoring equipment is used to determine the remainder from combustion (ash slack) of coal in wagons designed for power stations. Next to the rails, a neutron source (252 Cf, 241 Am/Be) is situated, which irradiates the coal with neutrons at a known dose, which produces the reaction 27 Al (n ..gamma..) Al 28. The aluminium content is a measure of the remainder. The 1.78 MeV energy is measured downstream of the rail with a detector. The neutron source can only act in the working position of a loaded wagon.

  9. Management of Transportation Equipment.

    Science.gov (United States)

    1982-11-01

    Record% % %. "jP -M -. M LIh TRANSPORTATION MAENTKENAI4CE SHOP WORKLOAD CONTROL WORK CENTER SADR A-OR .a’* tLR 4.,R53 8114LM 0 o 251 50 75 100 125 ISO ...PDBP 06 7 4892 TRACTOR, WHEEL, INDUST, 14001-20000 PDBP 06 7 4893 TRACTOR, WHEEL, INDUST, 20001-27000 PDBP 06 7 4894 TRACTOR, WHEEL, INDUST, 27001 PDBP...27K TRACTOR, WHEEL, INDUST, 27001 PDBP & UP P-i LINE ITEM 07 LIGHTING AND POWER GENERATION EQUIPMENT 5110 T FLOODLIGHT ELEC FLOODLIGHT, ELEC, TRUCK

  10. Californium-252 Program Equipment Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Chattin, Fred Rhea [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wilson, Kenton [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ezold, Julie G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-12-01

    To successfully continue the 252Cf production and meet the needs of the customers, a comprehensive evaluation of the Building 7920 processing equipment was requested to identify equipment critical to the operational continuity of the program.

  11. IMPACT DE L’ORIENTATION SUR LE CONFORT THERMIQUE INTERIEUR DANS L’HABITATION COLLECTIVE : Cas de la nouvelle ville Ali Mendjeli, Constantine

    Directory of Open Access Journals (Sweden)

    S BELLARA LOUAFI

    2009-06-01

    Une étude est effectuée sur le site de la nouvelle ville ALI MENDJELI de Constantine afin de comparer et de chercher la relation entre les éléments du climat et l’orientation. Une investigation sur terrain (relevé des températures, humidité relatives, températures de surfaces est entreprise pour évaluer la réponse quantitative globale pour ce type de climat (semi aride. Parallèlement à cela une simulation à l’aide d’un logiciel TRNSYS (version 14.1 a été effectuée pour tester plusieurs possibilités d’orientations et d’améliorations afin de déterminer les éléments qui peuvent servir à des conditions meilleures. Les résultats montrent que la prise en compte du critère orientation fait participer le bâtiment à une conception plus performante thermiquement et plus économe énergétiquement.

  12. Dosimetry techniques of thermal neutrons and {gamma} radiation in reactor cores; Techniques de dosimetrie des neutrons thermiques et du rayonnement {gamma} dans les piles

    Energy Technology Data Exchange (ETDEWEB)

    Sutton, J; Draganic, I; Hering, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    Chemical studies under radiation done in the reactor cores require to be followed by dosimetry. When the irradiations are done in the reflector, one can limit to the measure of the {gamma} and the neutron radiation. For the dosimetry of the {gamma} radiation, a dosimeter of ferrous sulfate is convenient until doses of about 10{sup 6} rep. The use of aired oxalic acid solutions permits to reach 10{sup 7} rep. The dosimetry of thermal neutrons has been made with solutions of cobalt sulphate or paper filter impregnated with this salt. The total chemical effect of the {gamma} and of the slow neutrons radiation is obtained with solutions of ferrous sulfate added with lithium sulphate. (M.B.) [French] Les etudes de chimie sous radiation faites dans les piles exigent d'etre suivies par dosimetrie. Lorsque les irradiations sont effectues dans le reflecteur, on peut se limiter a doser le rayonnement {gamma} et les neutrons. Pour la dosimetrie du rayonnement {gamma}, un dosimetre a sulfate ferreux convient jusqu'a des doses d'environ 10{sup 6} rep. L'emploi de solutions aerees d'acide oxalique permet d'atteindre 10{sup 7} rep. La dosimetrie des neutrons thermiques a ete faite avec des solutions de sulfate de cotalt ou du papier filtre impregne de ce sel. L'effet chimique total du rayonnement {gamma} et des neutrons lents est obtenu avec des solutions de sulfate ferreux additionne de sulfate de lithium. (M.B.)

  13. Thermal, intermediate and fast neutron flux measurements using activation detectors; Mesure des flux de neutrons thermiques, intermediaires et rapides au moyen de detecteurs par activation

    Energy Technology Data Exchange (ETDEWEB)

    Brisbois, J; Lott, M; Manent, G [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1964-07-01

    The problem of neutron flux measurements using activation detectors is studied in the particular case of protection research. It is shown how it possible, it is possible, using a known thermal flux, to organise a coherent calibration system for all the detectors. The rapid neutron detectors are calibrated with respect to a reference detector (phosphorus) in a natural uranium converter; the intermediate neutron detectors with respect to gold in the axial channel of ZOE. This method makes it possible to minimise the errors due to the activation cross-sections. A brief description is given of the counting room of the Pile Safety Study Service, as well of the practical utilisation characteristics of the counters employed. (authors) [French] Le probleme de la mesure des flux de neutrons au moyen de detecteurs par activation est etudie dans le cas particulier des etudes de protections. On montre comment, a partir d'un flux thermique connu, on peut organiser un systeme coherent d'etalonnage de tous les detecteurs. Les detecteurs de neutrons rapides sont etalonnes par rapport a un detecteur de reference (phosphore) dans un convertisseur en uranium naturel; les detecteurs de neutrons intermediaires, par rapport a l'or dans le canal axial de ZOE, Cette methode permet de minimiser les erreurs dues aux sections efficaces d'activation. On decrit sommairement la salle de comptage du Service d'Etudes de Protections de Piles et on indique les caracteristiques d'emploi pratique des detecteurs utilises. (auteurs)

  14. Les hydrocarbures aromatiques polycycliques dans l'environnement : la réhabilitation des anciens sites industriels The Polycyclic Aromatic Hydrocarbons in the Environment : the Former Industrial Sites Remediation

    Directory of Open Access Journals (Sweden)

    Costes J. M.

    2006-12-01

    Full Text Available Les hydrocarbures aromatiques polycycliques ou HAP peuvent être d'origine naturelle mais ils proviennent principalement des processus de pyrolyse. On peut les retrouver dans les sols de certains anciens sites industriels. Cela peut être le cas des sites d'anciennes usines à gaz. Même si aucune conséquence sur la santé humaine n'a été signalée et même si les risques paraissent virtuels, le principe de précaution rend nécessaire de s'occuper des risques liés à ces anciens sites industriels. Gaz de France, propriétaire de 467 sites d'anciennes usines à gaz assume l'héritage industriel dans le cadre d'un protocole signé avec le ministère de l'Environnement. Après une étude des sols, une évaluation des risques est réalisée. En fonction des résultats de cette évaluation des risques et de l'usage du site (actuel et prévu, des solutions de traitement peuvent être mises en Suvre. Parmi les techniques applicables aux sols pollués par des HAP, un intérêt particulier s'est porté sur les traitements biologiques, en pleine évolution, qui offrent une solution économique bien adaptée au traitement de grands volumes de sols souillés par une pollution organique moyennement concentrée. Polycyclic aromatic hydrocarbons (PAHs can be found under natural conditions but they can be produced by pyrolysis processes. They can be found in former industrial sites subsoil, especially on Manufactured Gas Plant sites (MGP sites. Gaz de France has inherited the patrimony of former French gas companies on nationalisation in 1946; consequently, Gaz De France is still the owner of 467 of manufactured gas plants. Even if no impact on human health has been detected and even if the risks seem to be virtual, Gaz de France has to prevent any environmental consequence due to the possible presence of residues in the subsoil of the sites: a protocol has been signed with the French Ministry of Environment. Following the investigations on the site, a

  15. Characterization equipment essential drawing plan

    International Nuclear Information System (INIS)

    WILSON, G.W.

    1999-01-01

    The purpose of this document is to list the Characterization equipment drawings that are classified as Essential Drawings. Essential Drawings: Are those drawings identified by the facility staff as necessary to directly support the safe operation of the facility or equipment (HNF 1997a). The Characterization equipment drawings identified in this report are deemed essential drawings as defined in HNF-PRO-242, Engineering Drawing Requirements (HNF 1997a). These drawings will be prepared, revised, and maintained per HNF-PRO-440, Engineering Document Change Control (HNF 1997b). All other Characterization equipment drawings not identified in this document will be considered Support drawings until the Characterization Equipment Drawing Evaluation Report is completed

  16. Coal mining equipment

    International Nuclear Information System (INIS)

    Stein, R.R.; Martin, T.W.

    1991-01-01

    The word in longwall components is big, and these larger components have price tags to match. The logic behind the greater investment is that it will yield high production rates and good uptime statistics. This is true in most cases. More important than single-shift tonnage records, average shift production continues to climb upwards. This paper reports on the quality, and more significantly, the quantity of service supplied for long-wall equipment, which has reached levels that would have been seen as unachievable when longwall mining was first introduced in the U.S. The school of thought then was that longwall would increase productivity in part by reducing the number of production units and thus reducing the number of personnel employed underground. The expectation of fewer employees turned out to be unrealistic. That was probably one reason that some early attempts to install longwall system looked more like failures than vision of the future

  17. Reactor fuel charging equipment

    International Nuclear Information System (INIS)

    Wade, Elman.

    1977-01-01

    In many types of reactor fuel charging equipment, tongs or a grab, attached to a trolley, housed in a guide duct, can be used for withdrawing from the core a selected spent fuel assembly or to place a new fuel assembly in the core. In these facilities, the trolley may have wheels that roll on rails in the guide duct. This ensures the correct alignment of the grab, the trolley and fuel assembly when this fuel assembly is being moved. By raising or lowering such a fuel assembly, the trolley can be immerged in the coolant bath of the reactor, whereas at other times it can be at a certain level above the upper surface of the coolant bath. The main object of the invention is to create a fuel handling apparatus for a sodium cooled reactor with bearings lubricated by the sodium coolant and in which the contamination of these bearings is prevented [fr

  18. Thermal conductivity of sintered UO{sub 2} under in-pile conditions; Conductibilite thermique de l'UO{sub 2} fritte dans les conditions d'utilisation en pile

    Energy Technology Data Exchange (ETDEWEB)

    Stora, J P; Bernardy De Sigoyer, B; Delmas, R; Deschamps, P; Lavaud, B; Ringot, C [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    The temperature distribution in a stack of sintered UO{sub 2} cylinders has been studied both in the laboratory where the heat energy is produced by an axial heating element, and in-pile, where the heating is due solely to nuclear effects. Under a high thermal gradient the UO{sub 2} cracks both along radial planes and along pseudo-cylindrical surfaces: these latter act as thermal barriers to the heat flow, It is therefore an apparent thermal conductivity k{sub a}(T), lower than the intrinsic value k(T) of this parameter which is measured. The efficiency of these barriers decreases when the gap decreases and when the external pressure acting on the cracked stack increases: in the limiting case, for high values of the binding strain, k{sub a}(T) {approx_equal} k(T). In the domain of phonon conduction (T {<=} 1350 deg C), the expression kw.cm{sup -1}.C{sup -1}=1/(11+0.024*T) accounts for the real thermal conductivity. Above 1350 deg C the thermal conductivity increases. Two in-pile measurements up to 1250 deg C carried out using cartridges fitted with thermocouples confirm, within the limits of experimental error, the above expression and the qualitative effects of the binding strains. Similar tests have been carried out-of-pile and in-pile on the real shape of the EL-4 fuel 'pencils'. Out-of-pile, the influence of the initial free gap, of the nature of the gas filing the 'pencil' and of the external pressure have been studied; the results are compatible with the above interpretation; It appears that an external pressure of 60 kg/cm{sup 2} is insufficient to restore completely the thermal conductivity of the fuel. (authors) [French] La distribution de temperature dans un empilement de cylindres d'UO{sub 2} fritte est etudiee a la fois au laboratoire, ou l'energie calorifique est produite par un element chauffant axial, et en pile, ou l'echauffement est uniquement nucleaire. Sous gradient thermique eleve, l'UO{sub 2} se fracture a la fois suivant des plans radiaux et

  19. Chapter 12. Space Heating Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Rafferty, Kevin D.

    1998-01-01

    The performance evaluation of space heating equipment for a geothermal application is generally considered from either of two perspectives: (a) selecting equipment for installation in new construction, or (b) evaluating the performance and retrofit requirements of an existing system. With regard to new construction, the procedure is relatively straightforward. Once the heating requirements are determined, the process need only involve the selection of appropriately sized hot water heating equipment based on the available water temperature. It is important to remember that space heating equipment for geothermal applications is the same equipment used in non-geothermal applications. What makes geothermal applications unique is that the equipment is generally applied at temperatures and flow rates that depart significantly from traditional heating system design. This chapter presents general considerations for the performance of heating equipment at non-standard temperature and flow conditions, retrofit of existing systems, and aspects of domestic hot water heating.

  20. Thermal diffusivity measurements between 0 {sup 0}C and 2000 {sup 0}C: application to UO{sub 2}; Mesure de la diffusivite thermique de 0 {sup 0}C et 2000 {sup 0}C application a UO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Van Craeynest, J C; Weilbacher, J C; Lallement, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1969-07-01

    We have built two types of apparatus to measure the thermal diffusivity of ceramic fuels. The first apparatus, based on Angstrom's method, operates between 0 deg. C and 1000 deg. C. Satisfactory results have been obtained for iron, nickel and molybdenum. The other apparatus, based on Cowan's method, operates between 1000 deg. C and 2000 deg. C on thin slabs. The thermal conductivity of UO{sub 2} has been measured from 0 deg. C to 2000 deg. C. There is a good agreement between our results and the well known values for UO{sub 2}. (authors) [French] Afin d'etudier la conductibilite thermique des combustibles ceramiques, nous avons mis au point deux types d'appareils nous permettant de mesurer la diffusivite thermique {alpha}, la conductibilite etant egale au produit de la diffusivite par la densite et la chaleur specifique. Un premier type d'appareil base sur la methode d'Angstroem nous permet d'obtenir des resultats de diffusivite sur echantillon de fabrication courante entre 0 deg.C et 1000 deg. C. Une serie de mesures a ete effectuee sur le fer, le nickel et le molybdene afin de controler le bon fonctionnement des appareils. Un deuxieme type d'appareil base sur la methode de Cowan nous permet d'atteindre la diffusivite thermique d'echantillons minces entre 1000 deg. C et 2000 deg. C. Un controle des resultats obtenus sur l'oxyde d'uranium a moyenne et haute temperature nous permet de conclure a un tres bon accord entre nos resultats et ceux de la litterature. (auteurs)

  1. Etude expérimentale sur le comportement d’un nouveau type d’accumulateur d’énergie thermique. Déterminations préliminaires sur l’installation expérimentale

    Directory of Open Access Journals (Sweden)

    Valentin Pavel

    2004-01-01

    Full Text Available On présente la première partie d’une étude concernant le comportement d’un nouveau type d’accumulateur d’énergie thermique. Sont présentées les déterminations se référant au comportement de l’unité centrale de stockage dans la phase de relaxation (refroidissement libre afin d’établir les pertes de chaleur, pour avoir une approche correcte des phénomènes dans les étapes ultérieures des études concernant l’accumulateur.

  2. Equipment repair in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, S

    1982-01-01

    Most equipment in Chinese coal mines consists of machinery and equipment produced in the 1950s; the efficiency of 4-62, CTD-57 and 70B/sub 2/ ventilators is 15% lower than that of new ones; that of SSM and AYaP pumps, 10% lower than of modern ones. Equipment renovation is done in three ways: replacing obsolete equipment with new equipment of the same type; improving the performance of existing equipment by introducing efficiency and reconstruction; and replacing obsolete equipment with advanced equipment. It is indicated that the second way, for example, replacement of 4-62 ventilator blades with a maximum efficiency of 73% by 4-72 ventilator blades raises its efficiency to 90%. Replacing the 8DA-8x3 water pump, having a maximum efficiency of 63%, with the 200D 43x3 pump with a maximum efficiency of 78%, enables an electricity savings of 7000 yuan per year, which exceeds all replacement costs (600 yuan). The need to improve equipment maintenance and preventive work to increase equipment service life and to introduce new techniques and efficiency is noted.

  3. 21 CFR 866.4540 - Immunonephelometer equipment.

    Science.gov (United States)

    2010-04-01

    ...) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4540 Immunonephelometer equipment. (a) Identification. Immunonephelometer equipment for clinical use...

  4. 21 CFR 866.4520 - Immunofluorometer equipment.

    Science.gov (United States)

    2010-04-01

    ...) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4520 Immunofluorometer equipment. (a) Identification. Immunofluorometer equipment for clinical use with...

  5. Equipment standards for interventional cardiology

    International Nuclear Information System (INIS)

    Dowling, A.; Gallagher, A.; Walsh, C.; Malone, J.

    2005-01-01

    Interventional radiology has seen rapid growth in cardiology and represents an alternative to hazardous surgery. Recently there has been a substantial growth in the number of procedures being performed and interventional cardiology (IC) procedures are the most common interventional procedures in Europe. Advances in imaging technology have facilitated the development of increasingly complex radiological IC equipment. Currently, the technology is developing at a rate ahead of supporting research, equipment standards and a regulatory framework. International standards play a key role in the design, manufacture and performance of radiological IC equipment. A survey of 12 IC systems (15 imaging chains) was conducted in Irish hospitals. The aim of the study was to assess the imbalance between rapidly advancing technology and existing standards and to propose recommendations for new IC equipment standards. The results demonstrate the need for definitive equipment requirements and standardisation in the design, manufacture, acceptance and maintenance of IC equipment. (authors)

  6. Generation of equipment response spectrum considering equipment-structure interaction

    International Nuclear Information System (INIS)

    Lee, Sang Hoon; Yoo, Kwang Hoon

    2005-01-01

    Floor response spectra for dynamic response of subsystem such as equipment, or piping in nuclear power plant are usually generated without considering dynamic interaction between main structure and subsystem. Since the dynamic structural response generally has the narrow-banded shapes, the resulting floor response spectra developed for various locations in the structure usually have high spectral peak amplitudes in the narrow frequency bands corresponding to the natural frequencies of the structural system. The application of such spectra for design of subsystems often leads to excessive design conservatisms, especially when the equipment frequency and structure are at resonance condition. Thus, in order to provide a rational and realistic design input for dynamic analysis and design of equipment, dynamic equipment-structure interaction (ESI) should be considered in developing equipment response spectrum which is particularly important for equipment at the resonance condition. Many analytical methods have been proposed in the past for developing equipment response spectra considering ESI. However, most of these methods have not been adapted to the practical applications because of either the complexities or the lack of rigorousness of the methods. At one hand, mass ratio among the equipment and structure was used as an important parameter to obtain equipment response spectra. Similarly, Tseng has also proposed the analytical method for developing equipment response spectra using mass ratio in the frequency domain. This method is analytically rigorous and can be easily validated. It is based on the dynamic substructuring method as applied to the dynamic soil-structure interaction (SSI) analysis, and can relatively easily be implemented for practical applications without to change the current dynamic analysis and design practice for subsystems. The equipment response spectra derived in this study are also based on Tseng's proposed method

  7. Overall Equipment Effectiveness Implementation Criteria

    Science.gov (United States)

    Abramova, I. G.; Abramov, D. A.

    2018-01-01

    This article documents the methods applied in production control technics specifically focused on commonly used parameter OEE (Overall Equipment Effectiveness). The indicators of extensive and intensive use of equipment are considered. Their appointment this is comparison in the same type of production within the industry and comparison of single-type and / or different types of equipment in terms of capacity. However, it is shown that there is no possibility of revealing the reasons for the machine’s operation: productive / unproductive, with disturbances. Therefore, in the article reveals the approaches to calculating the indicator characterizing the direct operation of the equipment. The Machine Load coefficient is approaching closely to the indicator of the efficiency of the use of equipment. Methods analysis is proceeded through the historically applied techniques such as “Stopwatch” and “Motion” studies. Was performed the analysis of the efficiency index of OEE equipment using the comparable indexes performance of equipment in the Russian practice. An important indicator of OEE contains three components. The meaning of each of them reflects historically applicable indicators. The value of the availability of equipment indicator is close to the value of the equipment extensibility index. The value of the indicator of the efficiency of work can be compared with the characteristic of the capacity of the equipment and the indicator of the quality level can meet the requirements for compliance with the manufacturing technology. Shown that the sum of the values of the coefficient of “Availability” of the equipment and the value of the “Factor of compaction of working hours” are one. As well as the total value of the indicator “level of quality” and the coefficient of marriage given in the result unit. The measurability of the indicators makes it possible to make a prediction about efficiency of the equipment.

  8. Information technology equipment cooling system

    Science.gov (United States)

    Schultz, Mark D.

    2014-06-10

    According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools warm air generated by the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat from the rack of information technology equipment.

  9. Management methodology for pressure equipment

    Science.gov (United States)

    Bletchly, P. J.

    Pressure equipment constitutes a significant investment in capital and a major proportion of potential high-risk plant in many operations and this is particularly so in an alumina refinery. In many jurisdictions pressure equipment is also subject to statutory regulation that imposes obligations on Owners of the equipment with respect to workplace safety. Most modern technical standards and industry codes of practice employ a risk-based approach to support better decision making with respect to pressure equipment. For a management system to be effective it must demonstrate that risk is being managed within acceptable limits.

  10. Cryogenic equipment; Materiel cryogenique

    Energy Technology Data Exchange (ETDEWEB)

    Leger, L; Javellaud, J; Caro, C; Gilguy, R; Testard, O

    1966-06-01

    The cryostats presented here were built from standard parts; this makes it possible to construct a great variety of apparatus at minimum cost. The liquid nitrogen and helium reservoirs were designed so as to reduce losses to a minimum, and so as to make the cryostats as autonomous as possible. The experimental enclosure which is generally placed in the lower part of the apparatus requires a separate study in every case. Furthermore, complete assemblies such as transfer rods, isolated traps and high vacuum valves, were designed with a similar regard for the economic aspects and for the need for standardization. This equipment thus satisfies a great variety of experimental needs; it is readily adaptable and the consumptions of helium and liquid nitrogen are very low. (authors) [French] De nombreuses experiences utilisant les basses temperatures, necessitent l'emploi d'un materiel cryogenique complexe n'existant pas dans le commerce. Les cryostats presentes ici ont ete realises a partir d'elements standard, ce qui permet, malgre la diversite des appareils, de realiser un ensemble a moindre frais. Les reservoirs d'azote et d'helium liquides ont ete concus de facon a limiter les pertes et a conferer au cryostat la plus grande autonomie possible. L'enceinte experimentale situee en general dans la partie inferieure de l'appareil necessite dans tous les cas une etude speciale. D'autre part des ensembles complets tels que les cannes de transfert, piege isole, robinet pour vide secondaire, ont ete concus dans le meme souci de rentabilite et de standardisation. Ce materiel peut donc repondre a un grand nombre d'exigences experimentales, il est facilement adaptable, et les consommations d'helium et d'azote liquide sont tres reduites. (auteurs)

  11. 29 CFR 1926.952 - Mechanical equipment.

    Science.gov (United States)

    2010-07-01

    ... equipment that are not covered with insulating protective equipment. (c) Derrick trucks, cranes and other lifting equipment. (1) All derrick trucks, cranes and other lifting equipment shall comply with subpart N...

  12. 22 CFR 135.32 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  13. 21 CFR 1403.32 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  14. 45 CFR 602.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  15. 49 CFR 18.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  16. 34 CFR 80.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  17. 10 CFR 600.232 - Equipment.

    Science.gov (United States)

    2010-01-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  18. 45 CFR 1183.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  19. Measure of the slowing down area of thermal state 1,45 eV neutrons in the graphite; Mesure de l'aire de ralentissement des neutrons dans le graphite de 1,45 eV a l'etat thermique

    Energy Technology Data Exchange (ETDEWEB)

    Robert, C [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1956-12-15

    The life of a neutron emitted as a fast one within a moderating medium may be divided into two parts; at first it is slowed down colliding with the nuclei of the medium; later on, as soon as its energy is of the order of the thermal agitation energy, it diffuses until captured by some nucleus. As a matter of fact, dividing the evolution of a neutron into two phases, a slowing down phase and a diffusing phase is arbitrary, since the thermal equilibrium is attained stepwise. This report is intended to examine the means of inferring the distribution of thermal neutrons from the distribution of fast neutrons on the basis of the distribution of nascent thermal neutrons and of the law of scattering. (author) [French] La vie d'un neutron emis a l'etat rapide dans un milieu moderateur comprend 2 parties: au debut il se ralentit par chocs sur les noyaux du milieu; ensuite, lorsque son energie est de l'ordre de l'energie d'agitation thermique, il diffuse jusqu'a sa capture par un noyau. La separation de l'evolution d'un neutron en deux phases, phase de ralentissement, puis phase de diffusion, est, en realite, arbitraire; un neutron doit atteindre l'equilibre thermique progressivement. L'objet de ce rapport est de voir comment on peut deduire la repartition des thermiques de la repartition des rapides connaissant la repartition des thermiques naissants et la loi de diffusion. (au0010te.

  20. Some examples of a differential calorimeter use for low temperature thermal effects measurement; Quelques exemples d'utilisation d'un calorimetre differentiel a puissance compensee pour des mesures d'anomalies thermiques a basses temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Bochirol, L; Bonjour, E

    1967-07-01

    The principle of a differential calorimeter is briefly described. The apparatus allows a direct and continuous determination of the differential heat-capacity between a sample and a reference, in the range 20 to 600 deg. K approximately. Some examples concerning measurements at low temperatures of reversible or non reversible thermal effects are given. They show the possibilities of the apparatus and are connected with: - detection and measurements of thermal effects associated to structural transformations in elastomers at low temperatures, - measurements of Wigner energy released after neutron irradiations at 77 deg. K for: recrystallized pyro-graphites; high purity iron, aluminium. [French] On decrit brievement le principe d'un calorimetre differentiel qui permet la determination directe et continue de la difference de chaleur specifique apparente entre un echantillon et une reference, dans une gamme de temperatures s'etendant de 20 a 600 deg. K environ. On donne quelques exemples de mesure a basses temperatures d'effets thermiques reversibles ou non reversibles. Ils montrent les possibilites de l'appareillage et concernent: - la detection et la mesure d'effets thermiques associes a des transformations structurales dans des elastomeres a basse temperature, - la mesure du degagement d'energie Wigner apres des irradiations neutroniques a 77 deg. K dans: des pyrographites recristallises; du fer de haute purete et de l'aluminium. (auteurs)

  1. Modification of non metallic materials under the influence of the radiation and thermal retrogradation of these modifications; Modification de materiaux non metalliques sous l'influence des rayonnements et retrogradation thermique de ces modifications

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, G; Perio, P; Gigon, J; Tournarie, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    The action of the radiation on solids constitute an extremely vast domain of study, which the CEA hardly begins. There is not a very long time, indeed, that we have relatively intense fluxes (6.10{sup 12} thermal neutrons by cm{sup 2}.s{sup -} {sup 1} in the center of the reactor core of Saclay). Materials submitted to radiations, were followed by the evolution of a certain number of physical properties. The study of thermal retrogradation, at moderate temperature, of the modifications provoked by the irradiation were also followed. We will limit, in this report, to expose our experiences on graphite and lithium fluoride. (M.B.) [French] L'action des rayonnements sur les solides constitue un domaine extremement vaste dont l'etude, au Commissariat a l'Energie Atomique, commence a peine. Il n'y a pas tres longtemps, en effet, que nous disposons de flux relativement intenses (6.10{sup 12} neutrons thermiques par cm{sup 2}.s{sup -1} au centre de la pile de Saclay). Dans les materiaux soumis au rayonnement nous suivons l'evolution d'un certain nombre de proprietes physiques et nous etudions la retrogradation thermique, a temperature moderee, des modifications provoquees par l'irradiation. Nous nous bornerons ici a exposer nos experiences sur le graphite et le fluorure de lithium. (M.B.)

  2. Food Service Equipment and Appurtenances.

    Science.gov (United States)

    National Sanitation Foundation, Ann Arbor, MI.

    Equipment design specifications are presented relating to tables of all kinds, counters, sinks and drainboards, bins, shelves, drawers, hoods and similar kitchen appurtenances, not including baking, roasting, toasting, broiling or frying equipment, food preparation machinery such as slicers, choppers, and cutters, mixers and grinders, steam…

  3. Equipe de trabalho

    Directory of Open Access Journals (Sweden)

    Gabriel Gerber Hornink

    2014-08-01

    Full Text Available   Equipe de Trabalho 2014 1. Equipe editorial Editor-Chefe Bayardo Bapstista Torres, Instituto de Química - USP, Brasil Eduardo Galembeck, Departamento de Bioquímica Instituto de Biologia UNICAMP, Brasil   Editores Gabriel Gerber Hornink, Depto. Bioquímica, Instituto de Ciências Biomédicas, Universidade - Federal de Alfenas - Unifal-MG, Brasil Vera Maria Treis Trindade, Instituto de Ciências Básicas da Saúde, Departamento de Bioquímica, Universidade Federal do Rio Grande do Sul, Brasil   Corpo Editorial Adriana Cassina, Departamento de Bioquímica, Facultad de Medicina, Universidad de la República, Uruguai Angel Herráez, Departamento de Bioquímica y Biología molecular, Universidad de Alcalá de Henares, Madrid, Espanha André Amaral Gonçalves Bianco, Universidade Federal de São Paulo (Unifesp, Brasil Denise Vaz de Macedo, Departamento de Bioquímica, Instituto de Biologia, Universidade Estadual de Campinas - Unicamp, Brasil Eneida de Paula, Departamento de Bioquímica, Instituto de Biologia, Universidade Estadual de Campinas - Unicamp, Brasil Guilherme Andrade Marson, Instituto de Química - USP, Brasil Jose Antonio Martinez Oyanedel, Universidad de Concepción, Chile Josep Maria Fernández Novell, Dept. Bioquímica i Biologia Molecular Universitat de Barcelona, Espanha Leila Maria Beltramini, Instituto de Física de São Carlos, Universidade Estadual de São Paulo - USP, Brasil Manuel João da Costa, Escola de Ciências da Saúde, Universidade do Minho, Portugal Maria Lucia Bianconi, Instituto de Bioquímica Médica Universidade Federal do Rio de Janeiro (UFRJ, Brasil María Noel Alvarez, Departamento de Bioquímica, Facultad de Medicina, Universidad de la República, Uruguai Miguel Ángel Medina Torres, Department of Molecular Biology & Biochemistry Faculty of Sciences University of Málaga, Espanha Nelma Regina Segnini Bossolan, Instituto de Física de São Carlos, Universidade de São Paulo - USP, Brasil Paulo De Avila

  4. Information technology equipment cooling method

    Science.gov (United States)

    Schultz, Mark D.

    2015-10-20

    According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools air utilized by the rack of information technology equipment to cool the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat generated by the rack of information technology equipment.

  5. Development of manufacturing equipment and QC equipment for DUPIC fuel

    International Nuclear Information System (INIS)

    Yang, Myung Seung; Park, J.J.; Lee, J.W.; Kim, S.S.; Yim, S.P.; Kim, J.H.; Kim, K.H.; Na, S.H.; Kim, W.K.; Shin, J.M.; Lee, D.Y.; Cho, K.H.; Lee, Y.S.; Sohn, J.S.; Kim, M.J.

    1999-05-01

    In this study, DUPIC powder and pellet fabrication equipment, welding system, QC equipment, and fission gas treatment are developed to fabricate DUPIC fuel at IMEF M6 hot cell. The systems are improved to be suitable for remote operation and maintenance with the manipulator at hot cell. Powder and pellet fabrication equipment have been recently developed. The systems are under performance test to check remote operation and maintenance. Welding chamber and jigs are designed and developed to remotely weld DUPIC fuel rod with manipulators at hot cell. Remote quality control equipment are being tested for analysis and inspection of DUPIC fuel characteristics at hot cell. And trapping characteristics is analyzed for cesium and ruthenium released under oxidation/reduction and sintering processes. The design criteria and process flow diagram of fission gas treatment system are prepared incorporating the experimental results. The fission gas treatment system has been successfully manufactured. (Author). 33 refs., 14 tabs., 91 figs

  6. TRANSPORT AND EMPLACEMENT EQUIPMENT DESCRIPTIONS

    International Nuclear Information System (INIS)

    1997-01-01

    The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) Transport and Emplacement in the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. The Transport and Emplacement equipment described in this document consists of the following: (1) WP Transporter; (2) Reusable Rail Car; (3) Emplacement Gantry; (4) Gantry Carrier; and (5) Transport Locomotive

  7. Containment and Surveillance Equipment Compendium

    International Nuclear Information System (INIS)

    Luetters, F.O.

    1980-02-01

    The Containment and Surveillance Equipment Compendium contains information sections describing the application and status of seals, optical surveillance systems, and monitors for international safeguards systems. The Compendium is a collection of information on equipment in use (generally by the IAEA) or under development in the US in diverse programs being conducted at numerous facilities under different sponsors. The Compendium establishes a baseline for the status and applications of C/S equipment and is a tool to assist in the planning of future C/S hardware development activities. The Appendix contains design concepts which can be developed to meet future goals

  8. Materials flow management in the metal industry. Design and techno-economical analysis of industriyl recycling concepts; Stoffstrommanagement in der Metallindustrie. Zur Gestaltung und techno-oekonomischen Bewertung industrieller Recyclingkonzepte

    Energy Technology Data Exchange (ETDEWEB)

    Haehre, S.

    2000-07-01

    Materials flow management is an attempt to cope with excessive consumption of resources and with the large-scale release of pollutants, both of which are hazards of our industrialised society. It is necessary to analyse materials and energy flow along interconnected product and process chains to develop suitable concepts, e.g. for innovative environmental protection and recycling measures. A planning instrument is designed for this purpose which is based on a combination of flowsheeting models common in chemical process engineering and material flow networks based on Petri nets. Its application enables computer-assisted design and techno-economic evaluation of industrial recycling concepts, so that decision makers in enterprises and administrations will be given a tool for in-house and external material flow management. In the implementation stage, the flowsheeting system 'Aspen Plus' and the eco-banancing tool 'Umberto' were used, and exemplary problems of material flow management in the steel and zinc industry were investigated. [German] Zur Ueberwindung negativer Umwelteinfluesse der Industriegesellschaft, die inbesondere aus dem Ressourcenverbrauch und der Freisetzung grosser Schadstoffmengen resultieren, werden Massnahmen im Sinne des Stoffstrommanagements gefordert. Die Entwicklung geeigneter Konzepte, etwa zum Einsatz innovativer Umweltschutz- und Recyclingmassnahmen, macht die Analyse von Stoff- und Energiestroemen entlang vernetzter Produkt- und Prozessketten erforderlich. Hierfuer wird ein Planungsinstrument konzipiert, das auf einer Kombination verfahrenstechnischer Flowsheeting-Modelle und Petri-Netz-basierter Stoffstromnetze beruht. Sein Einsatz ermoeglicht computergestuetzt die Gestaltung und techno-oekonomische Bewertung industrieller Recyclingkonzepte, so dass Entscheidungstraeger in Unternehmen und Behoerden ein Hilfsmittel zum betrieblichen und betriebsuebergreifenden Stoffstrommanagement erhalten. Bei der Implementierung

  9. Data Center Equipment Location and Monitoring System

    DEFF Research Database (Denmark)

    2013-01-01

    Abstract: Data center equipment location systems include hardware and software to provide information on the location, monitoring, and security of servers and other equipment in equipment racks. The systems provide a wired alternative to the wireless RFID tag system by using electronic ID tags...... connected to each piece of equipment, each electronic ID tag connected directly by wires to an equipment rack controller on the equipment rack. The equipment rack controllers link to a central control computer that provides an operator ...

  10. EAS Equipment Authorization Grantee Registrations

    Data.gov (United States)

    Federal Communications Commission — EAS (Equipment Authorization System). Radio Frequency (RF) devices are required to be properly authorized under 47 CFR Part 2 prior to being marketed or imported...

  11. ENERGY STAR Certified Imaging Equipment

    Data.gov (United States)

    U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 2.0 ENERGY STAR Program Requirements for Imaging Equipment that are effective as of...

  12. EMR Measurements on NDA Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Macdonell, Alexander Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meierbachtol, Krista Cruse [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Evans, James Walter Jr. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mayo, Douglas R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-07-10

    Electromagnetic radiation (EMR) emission strength measurements were performed on a suite of passive non-destructive assay (NDA) radiation detection equipment. Data were collected from 9 kHz up to 6 GHz on each of the assembled systems.

  13. Mongolia - Vocational Education - Equipment Upgrades

    Data.gov (United States)

    Millennium Challenge Corporation — Evaluation design The impact evaluation sought to identify the causal impact of exposure to equipment upgrades on subsequent outcomes. Insofar as we were not able to...

  14. Origins of eponymous orthopaedic equipment.

    Science.gov (United States)

    Meals, Clifton; Wang, Jeffrey

    2010-06-01

    Orthopaedists make great use of eponymous equipment, however the origins of these tools are unknown to many users. This history enriches, enlightens, and enhances surgical education, and may inspire modern innovation. We explored the origins of common and eponymous orthopaedic equipment. We selected pieces of equipment named for their inventors and in the broadest use by modern orthopaedists. We do not describe specialized orthopaedic implants and instruments owing to the overwhelming number of these devices. The history of this equipment reflects the coevolution of orthopaedics and battlefield medicine. Additionally, these stories evidence the primacy of elegant design and suggest that innovation is often a process of revision and refinement rather than sudden inspiration. Their history exposes surgical innovators as brilliant, lucky, hardworking, and sometimes odd. These stories amuse, enlighten, and may inspire modern orthopaedists to develop creative solutions of their own. The rich history of the field's eponymous instruments informs an ongoing tradition of innovation in orthopaedics.

  15. Operation monitor for plant equipment

    International Nuclear Information System (INIS)

    Kondo, Tetsufumi; Kanemoto, Shigeru.

    1991-01-01

    In a nuclear power plant, states of each of equipment in the plant are monitored accurately even under such a operation condition that the power is changed. That is, the fundamental idea is based on a model comparison method. A deviation between an output signal upon normal plant state obtained in a forecasting model device and that of the objective equipment in the plant are compared with a predetermined value. The result of the comparison is inputted to an alarm device to alarm the abnormality of the states of the equipment to an operator. The device of the present invention thus constituted can monitor the abnormality of the operation of equipment accurately even under such a condition that a power level fluctuates. As a result, it can remarkably contribute to mitigate operator's monitoring operation under the condition such as during load following operation. (I.S.)

  16. Equipment improvements for performance enhancement

    International Nuclear Information System (INIS)

    Gaestel, P.; Guesnon, H.; Sauze, G.

    1994-01-01

    In order to enhance the reactor availability, several improvements on reactor equipment have been developed: design optimization for stator maintenance replacement in the main alternator; adjustment modification of stator coils in the main alternator for an easier maintenance; improvement of the fuel handling line (pole crane, transfer equipment, loading machine); development of a loose part trapping system in the steam generator secondary circuit. 1 tab

  17. Low level photoneutron detection equipment

    International Nuclear Information System (INIS)

    Ji Changsong; Zhang Yuqin; Li Yuansui

    1991-01-01

    A low level photoneutron detection equipment has been developed. The photoneutrons produced by interaction of 226 Ra gamma quanta and deutron (D) target are detected with n-n discrimination detector made up of 3 He proportional counter array. The D-content information in the target can be obtained from the measured photoneutron counts. The equipment developed is mainly used for nondestructive D-content measurement of D-devices

  18. FUSRAP equipment concept development study

    International Nuclear Information System (INIS)

    Hinerman, K.B.; Smith, R.E.

    1981-01-01

    Under DOE contract, Dalton-Dalton-Newport, Inc. is performing an engineering evaluation of three selected FUSRAP sites in an effort to generate equipment concepts to perform remedial action for retrieval, packaging, storing, and transporting contaminated soil and other debris. Along with this engineering evaluation, an analysis of state and Federal regulations was made which had significant impact on the selected equipment and costs for each remedial action concept

  19. Remotely operated replaceable process equipment

    International Nuclear Information System (INIS)

    Westendorf, H.

    1987-01-01

    The coupling process of pneumatic and electrical auxiliary lines of a pneumatic control pressure line in a large cell of the reprocessing plant is carried out, together with the coupling process of the connecting flange of the process equipment. The coupling places of the auxiliary lines, such as control or supply lines, are laid in the flange parts of the flanges to be connected. The pipe flange on the frame side remains flush with the connecting flange of the process equipment. (DG) [de

  20. Partners in qualified equipment supply

    International Nuclear Information System (INIS)

    Rygg, D.E.; O'Hare, G.J.

    1993-01-01

    Industry initiatives have been taken to improve procurement practices and commercial dedication programs, formation of procurement engineering groups, emphasis on product quality, and increased engineering involvement in procurement and maintenance of qualified equipment. This poses new challenges for many licensees in terms of resources, product knowledge, and access to information normally held proprietary by equipment suppliers. Alternative approaches to future licensee/Westinghouse relationships which will allow licensees to adapt to the changing environment are discussed. 2 figs

  1. Wobbe index control system in gas industry processes; Systeme de controle de l'index de Wobbe du gaz naturel dans les processus industriels

    Energy Technology Data Exchange (ETDEWEB)

    Cassibba, M.; Bertani, M. [SNAM, (Italy)

    2000-07-01

    Natural gas supplied to industry for process utilizations originates from different sources and that can cause fluctuations in gas composition. Changing gas composition may lead to production problems in industry with sensitive thermal processes (particularly glass industry and thermal metal treatments), such as efficiency and product quality. An equipment suitable to control and adjust such variations has been developed. Experimental tests in laboratory were carried out in order to investigate the control system accuracy and reliability. In particular five different settings were tested: at a preset thermal input by adjusting the natural gas flow rate in respect to Wobbe Index variations; at a set furnace temperature and stack oxygen level with variable thermal input by monitoring the Wobbe Index value; at constant Wobbe Index value by adding air to natural gas; at constant thermal input and prefixed Wobbe Index value by adding air to natural gas and varying the air and gas mixture flow rate; gross calorific value control by adding air or LPG to natural gas. All the tested settings gave good results. This report illustrates these results and the main features of the control system. The control and regulation system was installed in two glass factories for field tests. (authors)

  2. 29 CFR 97.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

  3. 44 CFR 13.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

  4. 24 CFR 85.32 - Equipment.

    Science.gov (United States)

    2010-04-01

    ...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

  5. 41 CFR 105-71.132 - Equipment.

    Science.gov (United States)

    2010-07-01

    .... (4) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be... managing equipment (including replacement equipment), whether acquired in whole or in part with grant funds... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Equipment. 105-71.132...

  6. 43 CFR 12.72 - Equipment.

    Science.gov (United States)

    2010-10-01

    ...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

  7. 1968 Listing of Swimming Pool Equipment.

    Science.gov (United States)

    National Sanitation Foundation, Ann Arbor, MI. Testing Lab.

    An up-to-date listing of swimming pool equipment including--(1) companies authorized to display the National Sanitation Foundation seal of approval, (2) equipment listed as meeting NSF swimming pool equipment standards relating to diatomite type filters, (3) equipment listed as meeting NSF swimming pool equipment standard relating to sand type…

  8. Study of the thermal drop at the uranium-can interface for fuel elements in gas-graphite reactors; Etude de la chute thermique au contact uranium-gaine pour des elements combustibles de reacteur de la filiere graphite-gaz

    Energy Technology Data Exchange (ETDEWEB)

    Faussat, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Levenes, G; Michel, M [Societe Industrielle de Combustible Nucleaire (France)

    1964-07-01

    The report reviews the tests now under way at the CEA, for determining the thermal contact resistance at the uranium-can interface for fuel elements used in gas-graphite type reactors. These are laboratory tests carried out with equipment based on the principle of a heat flow across a stack of test pieces having planar contact surfaces. The following points emerge from this work: - for a metallic uranium element canned in magnesium, of the type G-2 or EDF-2, a value of 0.2 deg C/W/cm{sup 2} seems reasonable for can temperatures of 400 deg C and above. - this value is independent of the micro-geometric state of the uranium surface in a range of roughness which easily includes those observed on tubes and rods produced industrially. - for the internal cans of elements cooled internally and externally, the value of the contact resistance for temperatures of under 400 deg C as a function of the stresses in the can has not yet been measured exactly. (authors) [French] Le rapport fait le point des essais actuellement en cours au CEA pour determiner la resistance thermique de contact uranium-gaine pour des reacteurs de la filiere graphite-gaz. Ces essais sont effectues en laboratoire sur des appareils bases sur le principe d'une circulation de flux de chaleur a travers un empilement d'eprouvettes dont les faces en contact sont planes. De l'etude, il ressort essentiellement que: - pour un element a uranium metallique et gaine de magnesium type G-2 ou EdF-2, on peut admettre la valeur de 0,2 deg C/W/cm{sup 2} pour des temperatures de gaines de 400 deg C et plus. - cette valeur ne depend pas de l'etat de surface microgeometrique de l'uranium pour un domaine de rugosites couvrant largement celles que l'on observe sur des tubes et barreaux fabriques en serie. - pour les gaines internes d'elements a refroidissement interne et externe la valeur de la resistance de contact reste a preciser pour les temperatures inferieures a 400 deg C, en fonction des contraintes existant dans les

  9. Thermal and radiation induced polymerisation of carbon sub-oxide; Polymerisation thermique et sous rayonnement du sous-oxyde de carbone

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Michel

    1964-03-15

    eclaircis, nous pensons avoir assez de resultats concordants concernant la polymerisation du sous-oxyde de carbone pour pouvoir conclure en faveur d'un mecanisme ionique. Quant a la formule elle doit tres vraisemblablement comporter des enchainements de cycles lactoniques pour des raisons deja invoquees par d'autrus auteurs; mais l'examen du spectre infrarouge du polymere anhydre montre qu'il s'agit plutot de doubles cycles condenses pentagonaux, relies entre eux par des liaisons simples ou doubles selon la disposition des doubles liaisons a l'interieur des cycles. Recapitulons ci-dessous les principaux resultats en faveur d'un mecanisme ionique, ainsi que les objections qu'il est possible de leur opposer le cas echeant: 1 - Les capteurs de radicaux libres, NO, O{sub 2} ou CH{sub 3} - CH = CH{sub 3} ne modifient pas la vitesse de polymerisation thermique ou sous rayonnement. Ces gaz se retrouvant inchanges a la fin de la polymerisation. 2 - L'acetaldehyde a effectivement une action inhibitrice mais celle-ci n'est vraisemblablement pas de nature radicalaire car si on fait agir l'acetaldehyde sur un film de polymere anhydre et qu'on l'evacue ensuite le film n'a pas perdu ses proprietes catalytiques vis-a-vis d'une 'seconde' polymerisation (pas de periode d'induction), en outre nous avons constate que l'acetaldehyde ne supprimait pas le paramagnetisme du polymere. Nous avons deja interprete l'action inhibitrice de l'acetaldehyde comme etant due a une adsorption preferentielle, bien que nous n'ayons pas mesure directement cette adsorption. 3 - BF{sub 3} initie la polynerisation de C{sub 3}O{sub 2} en phase liquide, a basse temperature, et le polymere qu'on obtient de cette facon est paramagnetique, 4 - Inversement on a constate l'echec d'un essai d'initiation de la polymerisation pour un generateur de radicaux libres. 5 - L'action de l'eau montre que le paramagnetisme du polymere n'est pas du a des radicaux libres mais a la chaine de doubles liaisons conjuguees. Par contre l

  10. Browse Title Index

    African Journals Online (AJOL)

    Vol 6, No 1 (2010), Étude des performances thermiques d'un réfrigérateur local ... Vol 7, No 2 (2011), Évaluation des rejets d'eaux usées de la ville de Niamey ... Industriel : Cas de la plaine de la Meboudja, Nord-Est Algérien, Abstract PDF.

  11. rapid extraction of volatile compounds from citrus fruits using a ...

    African Journals Online (AJOL)

    M.A. Ferhat , M.N. Boukhatem, M. Hazzit 3, F.Chemat

    1 sept. 2016 ... que l'industrie chimique utilise des procédés utilisant les propriétés thermiques spécifiques ... moins de solvant, moins d'énergie et diminuant les rejets. ...... expression à froid à l'aide d'un appareil d'extraction semi industriel ...

  12. Performance monitoring of safeguards equipment

    International Nuclear Information System (INIS)

    Sirisena, K.; Peltoranta, M.; Goussarov, V.; Vodrazka, P.

    1999-01-01

    SGTCS is responsible for monitoring and reporting the performance of the SG equipment. Performance monitoring (PM) has been implemented in most important safeguards equipment operating unattended in nuclear facilities. Inspectors acquire equipment performance data in facilities. After inspection, the data package is submitted to SGTCS for processing and analysis. The performance data is used for identification of systems or components, which should be changed in the field and for identification of modules which, should be diagnosed at HQ in order to determine the cause of failure. Moreover, the performance data is used for preventive maintenance and spares distribution planning, and to provide statistics for official reports and management decision making. An important part of the performance monitoring is reporting. Equipment performance reports contain information about equipment inventory, utilization, failure types, failure distribution, and reliability. Trends in performance are given in graphical form in cases, where past data is available. Reliability estimates such as expected times between failures are provided. The automated reporting tools are obtainable through EMIS database application. (author)

  13. AVM branch vibration test equipment

    International Nuclear Information System (INIS)

    Anne, J.P.

    1995-01-01

    An inventory of the test equipment of the AVM Branch ''Acoustic and Vibratory Mechanics Analysis Methods'' group has been undertaken. The purpose of this inventory is to enable better acquaintance with the technical characteristics of the equipment, providing an accurate definition of their functionalities, ad to inform potential users of the possibilities and equipment available in this field. The report first summarizes the various experimental surveys conduced. Then, using the AVM equipment database to draw up an exhaustive list of available equipment, it provides a full-scope picture of the vibration measurement systems (sensors, conditioners and exciters) and data processing resources commonly used on industrial sites and in laboratories. A definition is also given of a mobile test unit, called 'shelter', and a test bench used for the testing and performance rating of the experimental analysis methods developed by the group. The report concludes with a description of two fixed installations: - the calibration bench ensuring the requisite quality level for the vibration measurement systems ; - the training bench, whereby know-how acquired in the field in the field of measurement and experimental analysis processes is made available to others. (author). 27 refs., 15 figs., 2 appends

  14. 78 FR 25916 - Authorization of Radiofrequency Equipment

    Science.gov (United States)

    2013-05-03

    ...] Authorization of Radiofrequency Equipment AGENCY: Federal Communications Commission. ACTION: Proposed rule... bodies, and measurement procedures used to determine RF equipment compliance. The Commission believes... Commission is responsible for an equipment authorization program for radiofrequency (RF) devices under part 2...

  15. Propagation of thermal neutrons in mock-up screw-shaped steel elements with water protection; Propagation des neutrons thermiques dans des fausses cartouches d'acier en helice dans une protection d'eau. Programme tournesol 3

    Energy Technology Data Exchange (ETDEWEB)

    Devillers, C L; Lanore, J M [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1967-07-01

    This report treats the streaming of thermal neutrons in a cylindrical duct in light water. The duct contains a spiral iron shield. Transmission and reflection matrices are used to describe the probabilities for the thermal neutrons to be absorbed or to be scattered on the surfaces. The neutron paths across the void are represented by geometrical matrices. The numerical resolution is performed by the Monte-Carlo method. (authors) [French] Dans ce rapport on traite un probleme de fuites de neutrons thermiques dans un canal cylindrique plonge dans l'eau et obture par un ecran helicoidal en acier. On utilise des matrices de transmission-reflexion pour decrire les probabilites d'absorption et de diffusion des neutrons sur les parois et l'helicoide et des matrices de correspondance geometrique pour representer la propagation dans le vide. La resolution numerique se fait par une methode de Monte-Carlo. (auteur)

  16. Compréhension de la stabilité thermique des alliages d'aluminium Al-Cu-Mg Understanding of the thermal stability of Al-Cu-Mg aluminum alloys

    Directory of Open Access Journals (Sweden)

    Pouget Gaëlle

    2013-11-01

    Full Text Available Les alliages d'aluminium 2xxx (Al-Cu-Mg sont connus pour être performants à chaud et sont par exemple utilisés pour certaines pièces de structure des avions. L'effet de la composition en Cu et Mg sur leur stabilité thermique, ainsi que celui de la précipitation durcissante associée ont été étudiés. Des comportements différents sont observés et trois zones de composition (en poids % identifiées: 3,1–3,7Cu et 1,6–2,0Mg : durcissement par la phase S' (Al2CuMg, limite d'élasticité ∼ 465 MPa à l'état T8 et bonne stabilité thermique jusqu'à 200 ∘C. 4,8–5,4Cu et 0–0,4Mg : durcissement par la phase θ' (Al2Cu, limite d'élasticité ∼ 380 MPa à l'état T8 et bonne stabilité thermique jusqu'à 300 ∘C. 3,7–4,3Cu et 0,9–1,3Mg : durcissement par S'+ θ', limite d'élasticité ∼ 470 MPa à l'état T8 mais stabilité thermique insuffisante à 150 ∘C et au delà; ce vieillissement important est associé à une concentration en Cu en solution solide élevée, ce qui accélère la cinétique de coalescence des précipités. La première zone de composition est donc recommandée pour des applications à température intermédiaire, typiquement 150 ∘C, et la seconde pour des applications à plus haute température, entre 250 et 300 ∘C. La troisième zone est à éviter pour des applications à 150 ∘C et au-delà. 2xxx aluminum alloys (Al-Cu-Mg have a good behaviour at elevated temperature and are used for some aircraft's structural parts. In this study, the effect of Cu and Mg content on the thermal stability and strengthening precipitation has been investigated. Three different behaviours are observed depending on the alloy composition: 3.1–3.7Cu, 1.6–2.0Mg: strengthening by S' (Al2CuMg, yield strength ∼ 465 MPa in T8 temper and good thermal stability up to 200 ∘C. 4.8–5.4Cu, 0–0.4Mg: strengthening by θ' (Al2Cu, yield strength ∼ 380 MPa in T8 and good thermal stability up to

  17. Problems Associated with the Monochromatisation of Slow Neutrons; Quelques aspects de la monochromatisation des neutrons thermiques; Nekotorye voprosy monokhromatizatsii medlennykh nejtronov; Algunos problemas de la monocromatizacion de neutrones lentos

    Energy Technology Data Exchange (ETDEWEB)

    Vertebnyj, V P; Kolotyj, V V; Majstrenko, A N

    1963-01-15

    The paper sets out the result of calculations to determine the shape of the spectral line of twin-rotor, pulsing, slow-neutron monochromators, as a function of the shifts in the phases between the rotors. Consideration is also given to die possibility of using certain light elements as slow-neutron filters. (author) [French] Les auteurs exposent les resultats de leurs calculs relatifs a la forme du spectre des monochromateurs a impulsions et a deux rotors pour neutrons thermiques en fonction de la distance et du dephasage entre les rotors. Ils examinent egalement la possibilite d*utiliser certains elements legers comme filtres a neutrons lents. (author) [Spanish] Los autores exponen ios resultadas de sus calculos relativos a la forma de la linea espectral de los monocromadores pulsantes de dos rotores para neutrones lentos en funcion de la distancia y del desias amiento de los rotores. Examinan asimismo la posibilidad de utilizar algunos elementos ligeros como filtros de neutrones lentos. (author)

  18. Parameterization and Observability Analysis of Scalable Battery Clusters for Onboard Thermal Management Paramétrage et analyse d’observabilité de clusters de batteries de taille variable pour une gestion thermique embarquée

    Directory of Open Access Journals (Sweden)

    Lin Xinfan

    2013-03-01

    Full Text Available Although the battery surface temperature is commonly measured, the core temperature of a cell may be much higher hence more critical than the surface temperature. The core temperature of a battery, though usually unmeasured in commercial applications, can be estimated by an observer, based on a lumped-parameter battery thermal model and the measurement of the current and the surface temperature. Even with a closed loop observer based on the measured surface temperature, the accuracy of the core temperature estimation depends on the model parameters. For such purpose, an online parameterization methodology and an adaptive observer are designed for a cylindrical battery. The single cell thermal model is then scaled up to create a battery cluster model to investigate the temperature pattern of the cluster. The modeled thermal interconnections between cells include cell to cell heat conduction and convection to the surrounding coolant flow. An observability analysis is performed on the cluster before designing a closed loop observer for the pack. Based on the analysis, guidelines for determining the minimum number of required sensors and their exact locations are derived that guarantee the observability of all temperature states. Bien que la température de surface d’une batterie soit généralement mesurée, la température interne d’une cellule peut être beaucoup plus élevée donc plus critique que la température de surface. La température interne d’une batterie, pourtant normalement non mesurée dans les applications commerciales, peut être évaluée par un observateur, sur la base d’un modèle thermique de batterie à constantes localisées et à partir de la mesure du courant et de la température de surface. Même avec un observateur en boucle fermée basé sur la température de surface mesurée, la précision de l’estimation de la température interne dépend des constantes du modèle. Dans cette optique, une méthodologie de

  19. Another donation of computer equipment

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    On Thursday 27 February, CERN was pleased to donate computer equipment to a physics institute in the Philippines.   H.E. Leslie J. Baja and Rolf Heuer. Following donations of computer equipment to institutes in Morocco, Ghana, Bulgaria, Serbia and Egypt, CERN is to send 50 servers and 4 network switches to the National Institute of Physics at the University of the Philippines Diliman. CERN’s Director-General Rolf Heuer and the Ambassador of the Philippines to Switzerland and Lichtenstein, H.E. Leslie J. Baja, spoke of their enthusiasm for the project during an official ceremony. The equipment will be used for various high energy physics research programmes in the Philippines and for the University’s development of digital resources for science.

  20. Ultrasonic Inspection following Heat Treatment of Uranium Alloys; Controle des Traitements Thermiques d'Alliage d'Uranium par Ultrasons; Kontrol' termicheskoj obrabotki uranovykh splavov s pomoshch'yu ul'trazvuka; Control Ultrasonico de los Tratamientos Termicos de Aleaciones de Uranio

    Energy Technology Data Exchange (ETDEWEB)

    Destribats, Marie-Therese; Cherpentier, C.; Papezik, F.; Pigeon, M. [Centre d' Etudes Nucleaires Desaclay (France)

    1965-10-15

    To improve the behaviour of low uranium alloys in reactors it is often necessary to reduce grain size by heat treatment. It has proved essential to provide for inspection of the whole element and the entire output in order to discover the exact quality of the fuel used. This inspection cannot be made by micrography because of the time required and the fact that the data obtained are incomplete. The inspection system adopted is based on the principle of absorption of ultrasonic waves by materials. This absorption depends on the structure of the medium. If {lambda} is small in relation to grain size G, absorption is low; whereas if G is of the order of {lambda}/2, absorption is very high. The tests were made first in air, using the multiple-echo system, then by measuring the height of the first echo, and finally by transmission in water, the height of the transmitted echo being compared with that of the initial signal. In industrial use, the amplitude of the echo transmitted by the material is compared with the echo obtained from a standard of the same characteristics and shape. Inspection takes place in a special machine in which the materials are rotated by rollers and adjustable transducers move over the element. The helicoidal scanning is carried out with a pitch of less than 5 mm. The ultrasonic generator includes a control system ensuring a constant reference echo. The paper quotes a series of records showing the results obtained with various alloys and in particular the faults observed in elements treated by induction upon linear displacement. The arrangement can detect faulty treatment zones of less than 1 cm{sup 2}. The system is at present used to inspect all low alloy uranium fuels of the G2, EL3, EDF1, EDF2 and INCA reactors, i.e. rods and tubes with diameters between 20 and 95 mm. (author) [French] Afin d'obtenir une meilleure tenue des alliages d'uranium faiblement allies dans les reacteurs, un affinage du grain par traitements thermiques est souvent

  1. Irradiation and development of the nuclear emulsions exposed to intense fluxes of thermal neutrons with {gamma} rays; Irradiation et developpement des emulsions nucleaires exposees a des flux intenses de neutrons thermiques, accompagnes de rayons {gamma}

    Energy Technology Data Exchange (ETDEWEB)

    Faraggi, H; Bonnet, A; Cohen, J [Commissariat a l' Energie Atomique, Lab. du Fort de Chatillon, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1952-07-01

    The thermal neutron fluxes provided by nuclear reactors permit the survey of relatively rare phenomenons, and dosage of very weak quantities of some elements. One of the most favorable detection technique are constituted by the use of the nuclear emulsions. one can mention: - the dosage of uranium by counting in the emulsion the number of traces due to fission fragments after irradiation. - The dosage of the lithium and the boron as trace amounts with the help of nuclear reactions (n, {alpha}) and thermal neutrons. - The research of reactions (n, {alpha}) or (n, p) of very weak cross section for middle or heavy elements. These different applications require however important neutrons fluxes. It had therefore obliged us to search for the most favorable irradiation and development of the emulsions conditions, to get the best visibility of the trajectories and decrease the phenomena of fog on the emulsion, which prevents any observation. (M.B.) [French] Les flux de neutrons thermiques fournis par les reacteurs nucleaires permettent l'etude de phenomenes relativement rares, et le dosage de tres faibles quantites de certains elements. Un des moyens de detection les plus favorables est constitue par l'utilisation des emulsions nucleaires. on peut citer: - le dosage de l'uranium par comptage dans l'emulsion du nombre de traces dues aux fragments de fission apres irradiation. - Le dosage du lithium et du bore a l'etat de traces a l'aide des reactions (n, {alpha}) sous l'action des neutrons thermiques. - La recherche de reactions (n,{alpha}) ou (n,p) de tres faible section efficace pour des elements moyens ou lourds. Ces differentes applications necessite cependant des flux de neutrons important. On a donc ete amene a rechercher les conditions les plus favorables d'irradiation et de developpement des emulsions, de maniere a obtenir la meilleure visibilite des trajectoires et diminuer les phenomenes de voile de l'emulsion, qui empeche toute observation. (M.B.)

  2. Waste Electrical and Electronic Equipment

    DEFF Research Database (Denmark)

    Bigum, Marianne Kristine Kjærgaard; Christensen, Thomas Højlund

    2011-01-01

    Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans and the env......Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans...

  3. The development of superconducting equipment

    CERN Document Server

    Ueda, T; Hiue, H

    2003-01-01

    Fuji Electric has been developing various types of superconducting equipment for over a quarter of a century. This paper describes the development results achieved for superconducting equipment and especially focuses on large-capacity current leads and superconducting transmission systems, the development of which is being promoted for application to the field of nuclear fusion. High temperature superconductor (HTS) is becoming the mainstream in the field of superconductivity, and the HTS floating coil and conduction-cooled HTS transformed are also introduced as recent developments for devices that utilize this technology. (author)

  4. Mechanical (turbines and auxiliary equipment)

    CERN Document Server

    Sherry, A; Cruddace, AE

    2013-01-01

    Modern Power Station Practice, Volume 3: Mechanical (Turbines and Auxiliary Equipment) focuses on the development of turbines and auxiliary equipment used in power stations in Great Britain. Topics covered include thermodynamics and steam turbine theory; turbine auxiliary systems such as lubrication systems, feed water heating systems, and the condenser and cooling water plants. Miscellaneous station services, and pipework in power plants are also described. This book is comprised of five chapters and begins with an overview of thermodynamics and steam turbine theory, paying particular attenti

  5. Study of radioactivity diffusion for bitumen-coated blocks produced by an industrial coating plant; Etude de la diffusion de la radioactivite de blocs d'enrobes bitumineux en provenance d'un atelier d'enrobage industriel

    Energy Technology Data Exchange (ETDEWEB)

    Rodier, J; Lefillatre, G [Commissariat a l' Energie Atomique, Chusclan (France). Centre de Production de Plutonium de Marcoule

    1969-07-01

    The solidification by bitumen of chemical coprecipitation sludges from the Marcoule waste treatment station has been studied in the laboratory and has led to the construction of an industrial coating plant. The quality of the coated material obtained has been controlled by the lixiviation test carried out with ordinary water and with sea-water on 45 ml laboratory samples and on industrial coated blocks of 150 litres. Tests on blocks of such a size have necessitated the installation of three special tanks. Two, each of 2000 litres capacity, contain ordinary and sea-water which was continuously recycled at a rate of 2.5 cm/hr and renewed periodically. In the third tank having a capacity of 11000 litres, the coated block was buried in earth and sprinkled with ordinary water with a view to studying the migration of radioelements in soil. The results of these tests confirm those obtained during the laboratory experiments. (authors) [French] La solidification par le bitume des boues de coprecipitation chimique de la station de traitement des effluents du Centre de Marcoule, etudiee en laboratoire, a conduit a la realisation d'une installation industrielle d'enrobage. La qualite de l'enrobe obtenu a ete controlee par le test de lixiviation qui a ete effectue en eau ordinaire et en eau de mer sur des echantillons de laboratoire de 45 ml et sur des blocs d'enrobe industriel de 150 litres. L'experimentation sur des blocs de telles dimensions a necessite l'installation de 3 cuves speciales. Deux, d'une capacite de 2000 litres, contiennent de l'eau ordinaire et de l'eau de mer recyclees en permanence a une vitesse de 2.5 cm/h et renouvelees periodiquement. Dans la 3eme cuve d'une capacite de 11000 litres, le bloc d'enrobe a ete enfoui dans de la terre et asperge d'eau ordinaire afin d'etudier la migration des radioelements dans le sol. Les resultats de ces essais confirment ceux obtenus au cours des tests de laboratoire. (auteurs)

  6. Aspects of industrial production of solid electrolyte fuel cells (SOFC) by thermal spraying technology; Aspekte industrieller Fertigung von Festelektrolyt-Brennstoffzellen (SOFC) mittels thermischer Beschichtungsverfahren

    Energy Technology Data Exchange (ETDEWEB)

    Weckmann, Hannes

    2010-07-01

    The present thesis deals with measures to optimize the large-volume production of Solid Oxide Fuel Cells (SOFC) based on thermal spraying technology. Based on the well-established Vacuum Plasma Spraying (VPS) at DLR the potential of alternative thermal spraying techniques as well as alternative base materials was investigated in order to deposit SOFC-anode, electrolyte and insulating layers. Production costs, reproducibility and long-term stability of the production process as well as the fuel cell performance were major target criteria. Depending on the parameter set applied when using the cost efficient Atmospheric Plasma Spraying (APS) in combination with Nickel-Graphite as base material a significant improvement of gas permeability and electrical conductivity was achieved in comparison to the VPS sprayed reference anode. The power density of a fuel cell with an APS-Nickel-Graphite anode (184 mW/cm{sup 2}) was slightly better than the performance with a VPS reference anode (159 mW/cm{sup 2}). In comparison to the VPS process, ceramic electrolyte layers of fully stabilized Zirconia (YSZ) with significantly higher gas tightness could be demonstrated when high energy processes such as Low Pressure Plasma Spraying (LPPS). Thin-film Low Pressure Plasma Spraying (LPPS-Thin-film) and High Velocity Oxy Fuel Spraying (HVOF) were applied. The power density of a fuel cell equipped with an HVOF electrolyte was significantly improved to 234 mW/cm{sup 2} as compared to 187 mW/cm{sup 2} with the VPS sprayed reference cell. Further improvement of the power density was achieved with an LPPS-electrolyte (273 mW/cm{sup 2}). HVOF and VPS sprayed layers of pure Spinel in composite with metallic active braze (equivalent to the sealing between individual layers in the fuel cell stack) could exceed the demanded charge transfer resistance of >1 k{omega}cm{sup 2} at 800 C operating temperature only in few cases. When blended base powder of Spinel and Magnesia in combination with the VPS

  7. Damage limits of accelerator equipment

    CERN Document Server

    Rosell, Gemma

    2014-01-01

    Beam losses occur in particle accelerators for various reasons. The effect of lost particles on accelerator equipment becomes more severe with the increasing energies and intensities. The present study is focused on the damage potential of the proton beam as a function of particle energy and beam size. Injection and extraction energies of different accelerators at CERN were considered.

  8. Pocket dictionary of laboratory equipment

    International Nuclear Information System (INIS)

    Junge, H.D.

    1987-01-01

    This pocket dictionary contains the 2500 most common terms for scientific and technical equipment in chemical laboratories. It is a useful tool for those who are used to communicating in German and English, but have to learn the special terminology in this field. (orig.) [de

  9. Using Gaming Equipment to Teach

    Science.gov (United States)

    Curriculum Review, 2009

    2009-01-01

    Gaming equipment (such as Nintendo's Wii[TM]) is making its way to schools and classrooms. However, most of the discussion regarding how to use this technology and integrate it into lesson plans is happening in blogs on the Internet. An advocate of interactive media in the classroom, Dr. Dawn Hawkins, a faculty member for the Art Institute of…

  10. Isotope-equipped measuring instruments

    International Nuclear Information System (INIS)

    Miyagawa, Kazuo; Amano, Hiroshi

    1980-01-01

    In the steel industry, though the investment in isotope-equipped measuring instruments is small as compared with that in machinery, they play important role in the moisture measurement in sintering and blast furnaces, the thickness measurement in rolling process and others in automatic control systems. The economic aspect of the isotope-equipped measuring instruments is described on the basis of the practices in Kimitsu Works of Nippon Steel Corporation: distribution of such instruments, evaluation of economic effects, usefulness evaluation in view of raising the accuracy, and usefulness evaluation viewed from the failure of the isotope instruments. The evaluation of economic effects was made under the premise that the isotope-equipped measuring instruments are not employed. Then, the effects of raising the accuracy are evaluated for a γ-ray plate thickness gauge and a neutron moisture gauge for coke in a blast furnace. Finally, the usefulness was evaluated, assuming possible failure of the isotope-equipped measuring instruments. (J.P.N.)

  11. Hydraulic turbines and auxiliary equipment

    Energy Technology Data Exchange (ETDEWEB)

    Luo Gaorong [Organization of the United Nations, Beijing (China). International Centre of Small Hydroelectric Power Plants

    1995-07-01

    This document presents a general overview on hydraulic turbines and auxiliary equipment, emphasizing the turbine classification, in accordance with the different types of turbines, standard turbine series in China, turbine selection based on the basic data required for the preliminary design, general hill model curves, chart of turbine series and the arrangement of application for hydraulic turbines, hydraulic turbine testing, and speed regulating device.

  12. Some Measurements of Thermal Neutron Spectra; Mesure de Spectres de Neutrons Thermiques; Nekotorye izmereniya spektrov teplovykh nejtronov; Algunas Mediciones de Espectros de Neutrones Termicos

    Energy Technology Data Exchange (ETDEWEB)

    Poole, M. J.; Schofield, P.; Sinclair, R. N. [United Kingdom Atomic Energy Authority, Research Group, Atomic Energy Research Establishment, Harwell (United Kingdom)

    1964-04-15

    River scattering-law data, in an attempt to predict the shape of the energy spectrum at positions in both blocks. A second experiment introduces a spatial discontinuity instead of thermal. A disc of cadmium sufficiently thick to be black to all neutrons below 0.4 eV is fixed centrally in a tank of water and spectra have been measured near to the disc as a function both of position and of direction of travel of the neutrons (relative to the plane of the cadmium). Finally may be mentioned spectrum measurements in a graphite-uranium lartice which provide a check on spectrum calculations in reactor geometry. Many spectrum experiments can be carried out in either critical or subcritical geometry, and in some discussion is given of the relative merits of those two methods of approach. (author) [French] Les auteurs ont entrepris a Harwell l'execution de travaux complementaires pour determiner la loi de diffusion dans le ralentisseur et pour verifier la validite de cette loi en procedant a des mesures du spectre. La plupart des experiences sur la loi de diffusion ont ete faites a Chalk River (Canada); le traitement des donnees se fait au Laboratoire national d'Argonne (Etats-Unis), et l'analyse ainsi que l'extrapolation necessaire des resultats des mesures se font a Harwell. Les mesures du spectre se divisent naturellement en deux groupes. En utilisant la spectroscopie du temps de vol, les auteurs ont fait un grand nombre de mesures de spectres de neutrons thermiques dans des ralentisseurs empoisonnes homogenes. Ces travaux completent ceux qui ont deja ete effectues par les auteurs et par Beyster et al.; ils servent a verifier les valeurs des sections efficaces du transfert d'energie o(E -> E) deduites de la loi de diffusion en usage. Toutefois, cette experience n'est nullement sensible aux variations angulaires de la diffusion ni a la partie de la section efficace de diffusion qui ne comporte pas de changement de l'energie du neutron diffuse; or, ces deux facteurs ont leur

  13. Thermal decomposition of uranyl nitrate hexahydrate. Study of intermediate reaction products; Decomposition thermique du nitrate d'uranyle hexahydrate etude des intermediaires de cette decomposition

    Energy Technology Data Exchange (ETDEWEB)

    Chottard, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1970-07-01

    The thermal decomposition of uranyl nitrate hexahydrate has been carried but at constant pressure and constant rate of reaction. The following intermediary products have been shown to exist and isolated: UO{sub 2}(NO{sub 3}){sub 2}.3H{sub 2}O; UO{sub 2}(NO{sub 3}){sub 2}. 2H{sub 2}O; UO{sub 2}(NO{sub 3}){sub 2}. H{sub 2}O; UO{sub 2}(NO{sub 3}){sub 2} and UO{sub 3}. These products, together with the hexahydrate UO{sub 2} (NO{sub 3}){sub 2}.6H{sub 2}O, have been studied by: - X-ray diffraction, using the Debye-Scherrer method.- infra-red spectrography: determination of the type of bonding for the water and the nitrate groups. - nuclear magnetic resonance: study of the mobility of water molecules. The main results concern: - the water molecule bonds in the series of hydrates with 6.3 and 2 H{sub 2}O. - isolation and characterization of uranyl nitrate monohydrate, together with the determination of its molecular structure. - the mobility of the water molecules in the series of the hydrates with 6.3 and 2 H{sub 2}O. An analysis is made of the complementary results given by infra-red spectroscopy and nuclear magnetic resonance; they are interpreted for the whole of the hydrate series. [French] La decomposition thermique du nitrate d'uranyle hexahydrate a ete effectuee en operant a pression et vitesse de decomposition constantes. Les produits intermediaires suivants ont ete mis en evidence et isoles: UO{sub 2}(NO{sub 3}){sub 2}, 3H{sub 2}O; UO{sub 2}(NO{sub 3}){sub 2}, 2H{sub 2}O; UO{sub 2}(NO{sub 3}){sub 2},H{sub 2}O; UO{sub 2}(NO{sub 3}){sub 2} et UO{sub 3}. Ces composes, ainsi que l'hexahydrate UO{sub 2}(NO{sub 3} ){sub 2}, 6H{sub 2}O ont ete etudies par: - diffraction des rayons X, selon la methode Debye-Scherrer.- spectrographie infra-rouge: determination des modes de liaison de l'eau et des groupements nitrate. - resonance magnetique nucleaire: etude de la mobilite des molecules d'eau. Les principaux resultats portent sur: - les liaisons des molecules d'eau dans la

  14. Alternative Fuels Data Center: Biodiesel Equipment Options

    Science.gov (United States)

    Equipment Options to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Equipment Options on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Equipment Options on Twitter Bookmark Alternative Fuels Data Center: Biodiesel Equipment Options on Google Bookmark Alternative Fuels

  15. 40 CFR 792.61 - Equipment design.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Equipment design. 792.61 Section 792.61...) GOOD LABORATORY PRACTICE STANDARDS Equipment § 792.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

  16. 40 CFR 160.61 - Equipment design.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160... LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation... appropriate design and adequate capacity to function according to the protocol and shall be suitably located...

  17. 21 CFR 58.61 - Equipment design.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

  18. 34 CFR 74.34 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... as program income. (e) When acquiring replacement equipment, the recipient may use the equipment to... replacement equipment subject to the approval of the Secretary. (f) The recipient's property management... 34 Education 1 2010-07-01 2010-07-01 false Equipment. 74.34 Section 74.34 Education Office of the...

  19. 20 CFR 437.32 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use.... Procedures for managing equipment (including replacement equipment), whether acquired in whole or in part... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Equipment. 437.32 Section 437.32 Employees...

  20. 45 CFR 2541.320 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... replacement equipment, the grantee or subgrantee may use the equipment to be replaced as a trade-in or sell... replacement equipment), whether acquired in whole or in part with grant funds, until disposition takes place... ensure the highest possible return. (e) Disposition. When original or replacement equipment acquired...

  1. 45 CFR 1174.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use... requirements. Procedures for managing equipment (including replacement equipment), whether acquired in whole or... original or replacement equipment acquired under a grant or subgrant is no longer needed for the original...

  2. 45 CFR 1157.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use... requirements. Procedures for managing equipment (including replacement equipment), whether acquired in whole or... original or replacement equipment acquired under a grant or subgrant is no longer needed for the original...

  3. The Cost of Maintaining Educational Communications Equipment.

    Science.gov (United States)

    Humphrey, David A.

    Tentative formulas for calculating the cost of maintaining educational communications equipment are proposed. The formulas are based on a survey of campuses of the State University of New York. The survey analyzed the types of equipment to be maintained, types of maintenance, who uses the equipment, who services the equipment, and the cost…

  4. Construction of an apparatus for measuring the low-temperature thermal conductivity before and after neutron irradiation. Application to uranium dioxide (1963); Realisation d'un appareil pour la mesure de la conductibilite thermique a basse temperature avant et apres irradiation neutronique. Application au dioxyde d'uranium (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Bethoux, O [Commisariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1963-09-15

    An apparatus has been studied and built which makes it possible to alternatively irradiate a sample at room temperature in the reactor 'Melusine' at the Grenoble Nuclear Research Centre, and to measure its thermal conductivity between 20 and 100 deg. K in perfect safety. The results obtained on UO{sub 2} have made it possible on the one hand to check experimentally that the spin-phonon diffusion leads to a thermal resistance independent of temperature above 30 deg. K, and on the other hand to propose a simple theory which takes into count the role played by the damage due to U-235 fission products in the decrease of thermal conductivity after irradiation. (author) [French] Un appareil permettant alternativement d'irradier un echantillon a temperature ambiante dans le reacteur ''Melusine'' du C.E.N.G., et de mesurer sa conductibilite thermique entre 20 et 100 deg. K en toute securite, a ete etudie et construit Les resultats obtenus sur UO{sub 2} ont permis, d'une part, de verifier experimentalement que la diffusion spin-phonon conduit a une resistance thermique independante de la temperature au-dessus de 30 deg. K, et, d'autre part, de proposer une theorie simple tenant compte du role joue par les degats dus aux produits de fission de l'uranium 235, dans la deterioration de la conductibilite thermique apres irradiation. (auteur)

  5. Contribution to the study on the flow rate adjustment for gas cooled power reactors (1964); Contributiom a l'etude de reglage du debit pour les reacteurs industriels refroidis par gaz (1964)

    Energy Technology Data Exchange (ETDEWEB)

    Milliot, B. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1961-06-15

    1. This original study firstly defines the problem of the adjustment of the coolant flow rate in a reactor channel as a function of the corresponding heat transfer equations and of the local and temporal neutron flux. The necessity of such an adjustment is pointed out and the modifying parameters are studied. An adjustment study using the envelope of the possible flux curves is developed. A short study on the technology and the economical advantage of this adjustment is presented. Some measurements, made on G-1 and G-2, show the precision one can obtain from adjustment apparatus itself as well as from the complete reactor adjustment system. 2. Evolution of nuclear properties of fuel in an heterogeneous thermal reactor. In the first port of this paper, the phenomena of fuel evolution have been mainly pointed out. Now a bibliographical study more qualitatively than quantitatively has been done. This survey specifies the present theories and relates to a real effective cross section and also yields to the bases of such a nuclear calculation. (author) [French] 1. Cette etude originale definit d'abord le probleme du reglage du debit de refrigerant dans un canal de reacteur en fonction de la formulation du calcul des performances thermodynamiques de ce canal et des variations du flux neutronique dans l'espace et le temps. La necessite du reglage est ensuite mise en evidence et les parametres le modifiant sont etudies. Une methode de reglage, basee sur l'emploi d 'une courbe enveloppe des courbes de flux possibles, est donnee. Une breve etude de la technologie et des incidences economiques du reglage est presentee. Des mesures effectuees sur les reacteurs G-1 et G-2 montrent la precision que l'on peut attendre des dispositifs de reglage comme du reglage d'ensemble du reacteur lui-meme. 2. Evolution des proprietes nucleaires du combustible dans un reacteur heterogene a neutrons thermiques. Les phenomenes d'evolution du combustible

  6. Contribution to the study on the flow rate adjustment for gas cooled power reactors (1964); Contributiom a l'etude de reglage du debit pour les reacteurs industriels refroidis par gaz (1964)

    Energy Technology Data Exchange (ETDEWEB)

    Milliot, B [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1961-06-15

    1. This original study firstly defines the problem of the adjustment of the coolant flow rate in a reactor channel as a function of the corresponding heat transfer equations and of the local and temporal neutron flux. The necessity of such an adjustment is pointed out and the modifying parameters are studied. An adjustment study using the envelope of the possible flux curves is developed. A short study on the technology and the economical advantage of this adjustment is presented. Some measurements, made on G-1 and G-2, show the precision one can obtain from adjustment apparatus itself as well as from the complete reactor adjustment system. 2. Evolution of nuclear properties of fuel in an heterogeneous thermal reactor. In the first port of this paper, the phenomena of fuel evolution have been mainly pointed out. Now a bibliographical study more qualitatively than quantitatively has been done. This survey specifies the present theories and relates to a real effective cross section and also yields to the bases of such a nuclear calculation. (author) [French] 1. Cette etude originale definit d'abord le probleme du reglage du debit de refrigerant dans un canal de reacteur en fonction de la formulation du calcul des performances thermodynamiques de ce canal et des variations du flux neutronique dans l'espace et le temps. La necessite du reglage est ensuite mise en evidence et les parametres le modifiant sont etudies. Une methode de reglage, basee sur l'emploi d 'une courbe enveloppe des courbes de flux possibles, est donnee. Une breve etude de la technologie et des incidences economiques du reglage est presentee. Des mesures effectuees sur les reacteurs G-1 et G-2 montrent la precision que l'on peut attendre des dispositifs de reglage comme du reglage d'ensemble du reacteur lui-meme. 2. Evolution des proprietes nucleaires du combustible dans un reacteur heterogene a neutrons thermiques. Les phenomenes d'evolution du combustible tiennent une place importante dans l

  7. [Equipment and technology in robotics].

    Science.gov (United States)

    Murphy, Declan; Challacombe, Ben; Nedas, Tim; Elhage, Oussama; Althoefer, Kaspar; Seneviratne, Lakmal; Dasgupta, Prokar

    2007-05-01

    We review the evolution and current status of robotic equipment and technology in urology. We also describe future developments in the key areas of virtual reality simulation, mechatronics and nanorobotics. The history of robotic technology is reviewed and put into the context of current systems. Experts in the associated fields of nanorobotics, mechatronics and virtual reality simulation simulation review the important future developments in these areas.

  8. Remote handling equipment for SNS

    International Nuclear Information System (INIS)

    Poulten, B.H.

    1983-01-01

    This report gives information on the areas of the SNS, facility which become highly radioactive preventing hands-on maintenance. Levels of activity are sufficiently high in the Target Station Area of the SNS, especially under fault conditions, to warrant reactor technology to be used in the design of the water, drainage and ventilation systems. These problems, together with the type of remote handling equipment required in the SNS, are discussed

  9. Margins related to equipment design

    International Nuclear Information System (INIS)

    Devos, J.

    1994-01-01

    Safety margins related to design of reactor equipment are defined according to safety regulations. Advanced best estimate methods are proposed including some examples which were computed and compared to experimental results. Best estimate methods require greater computation effort and more material data but give better variable accuracy and need careful experimental validation. Simplified methods compared to the previous are less sensitive to material data, sometimes are more accurate but very long to elaborate

  10. Temperature radiation measuring equipment. Temperaturstrahlungsmessgeraet

    Energy Technology Data Exchange (ETDEWEB)

    Lotzer, W

    1981-01-22

    The invention is concerned with a temperature radiation measuring equipment for non-contact temperature measurement by the light intensity variation method, with a photoelectric resistance as the measuring element. By having a circuit with a transistor, the 'dark resistance' occurring in the course of time is compensated for and thus gives a genuine reading (ie. the voltage drop across the photoelectric resistance remains constant).

  11. CERN computing equipment for Senegal

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    On 26 May, CERN once again had the honour of donating computing equipment to a foreign institute.   This time, around 100 servers and five network hubs were sent to Senegal, making it the seventh country, after Morocco, Ghana, Bulgaria, Serbia, Egypt and the Philippines, to receive a donation of computing equipment from the Organization. The official ceremony was held at CERN on 26 May in the presence of the Director-General, Rolf Heuer, and Senegal's ambassador to Geneva, Fodé Seck, who both expressed their enthusiasm for the project. The equipment is intended for Cheikh Anta Diop University (UCAD) in Dakar and will be of particular use to students attending the African School of Fundamental Physics and its Applications (ASP 2014) taking place from 3 to 23 August, for which CERN is a partner. The ASP allows a large number of African students to hone their skills in high-energy physics and to forge professional links with fellow physicists in Africa and Europe. ...

  12. JCE Online: Equipment Buyers Guide

    Science.gov (United States)

    Holmes, Jon L.

    1999-01-01

    The Equipment Buyers Guide was edited by Jo Rita Jordan. The new Equipment Buyers Guide, bound into the back of this issue, is also a new resource of JCE Internet. This resource provides an online source for the information contained in the printed guide. Placing this information online allows us to regularly update it and to provide live links to the suppliers' WWW sites. The organization of the online version parallels that of the print version. There is an alphabetical list of suppliers and a categorical listing. Links to these lists are provided on every page in the left-hand navigation bar. To quickly find information about a particular supplier, you click Supplier List, click the letter that begins the supplier's name, and scroll through the list to find the supplier. To find which suppliers provide a particular type of instrument or equipment, use the Categories link; click the category of the equipment you are looking for and then click the link to a supplier. You will then be taken to an alphabetical supplier listing page where you can scroll until you find the particular supplier of the item for which you are looking. Once you have found a supplier, the online Equipment Buyers Guide gives you the traditional contact information. But in addition, you also get one-click access to the WWW sites of the suppliers that have them. Depending on the site, you should be able to find information about the items that you seek and may even be able to order the items online! We think that you will find the online version of the Equipment Buyers Guide useful. To make it more useful, please send your suggestions, any errors or omissions you find, and any additional categories to the editor at jjordan@world.std.com The online Equipment Buyers Guide can be found at JCE Online at http://JChemEd.chem.wisc.edu/JCEWWW/Resources/EBG/ JCE Online in '99 JCE Online is your online source of "all things JCE". In order to provide you with an even more useful online resource, JCE

  13. Division of Scientific Equipment - Overview

    International Nuclear Information System (INIS)

    Halik, J.

    2002-01-01

    Full text: The Scientific Equipment Division consists of the Design Group and the Mechanical Workshop. The activity of the Division includes the following: * designs of devices and equipment for experiments in physics; their mechanical construction and assembly. In particular, these are vacuum chambers and installations for HV and UHV;* maintenance and upgrading of the existing installations and equipment in our Institute; * participation of our engineers and technicians in design works, equipment assembly and maintenance for experiments in foreign laboratories. The Design Group is equipped with PC-computers and AutoCAD graphic software (release 2000 and Mechanical Desktop 4.0) and an A0 plotter, which allow us to make drawings and 2- and 3-dimensional mechanical documentation to the world standards. The Mechanical Workshop offers a wide range of machining and treatment methods with satisfactory tolerances and surface quality. They include: * turning - cylindrical elements of a length up to 2000 mm and a diameter up to 400 mm, and also disc type elements of a diameter up to 600 mm and a length not exceeding 300 mm, * milling - elements of length up to 1000 mm and gear wheels of diameter up to 300 mm, * grinding - flat surfaces of dimensions up to 300 mm x 1000 mm and cylindrical elements of a diameter up to 200 mm and a length up to 800 mm, * drilling - holes of a diameter up to 50 mm, * welding - electrical and gas welding, including TIG vacuum-tight welding, * soft and hard soldering, * mechanical works including precision engineering, * plastics treatment - machining and polishing using diamond milling, modelling, lamination of various shapes and materials, including plexiglas, scintillators and light-guides, * painting - paint spraying with possibility of using furnace-fired drier of internal dimensions of 800 mm x 800 mm x 800 mm. Our workshop is equipped with the CNC milling machine which can be used for machining of work pieces up to 500 kg. The machine

  14. Used energy-related laboratory equipment grant program for institutions of higher learning. Eligible equipment catalog

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    This is a listing of energy related equipment available through the Energy-Related Laboratory Equipment Grant Program which grants used equipment to institutions of higher education for energy-related research. Information included is an overview of the program, how to apply for a grant of equipment, eligibility requirements, types of equipment available, and the costs for the institution.

  15. Data center equipment location and monitoring system

    DEFF Research Database (Denmark)

    2011-01-01

    A data center equipment location system includes both hardware and software to provide for location, monitoring, security and identification of servers and other equipment in equipment racks. The system provides a wired alternative to the wireless RFID tag system by using electronic ID tags...... connected to each piece of equipment, each electronic ID tag connected directly by wires to a equipment rack controller on the equipment rack. The equipment rack controllers then link over a local area network to a central control computer. The central control computer provides an operator interface......, and runs a software application program that communicates with the equipment rack controllers. The software application program of the central control computer stores IDs of the equipment rack controllers and each of its connected electronic ID tags in a database.; The software application program...

  16. Le néo-corporatisme réinterpellé : analyse comparée de deux politiques d'accès à l'emploi, l'apprentissage industriel en Belgique et le contrat de qualification "jeunes" en France

    OpenAIRE

    Levêque, Audrey

    2006-01-01

    L'étude comparative de l'apprentissage industriel en Belgique francophone et du contrat de qualification "jeunes" en France permet de réinterpeller le modèle néo-corporatiste d'Etat social. L'analyse de l'émergence et de la mise en oeuvre de ces deux politiques publiques d'accès à l'emploi pour les jeunes peu qualifiés permet de comprendre comment elles sont réappropriées par les acteurs de terrain et ce, plus particulièrement dans la branche de la métallurgie. Si ces politiques s'adressent t...

  17. Establishment for Nuclear Equipment: Overview

    International Nuclear Information System (INIS)

    Pracz, J.

    2001-01-01

    Full text: The activity of ZdAJ in 2000 was focused on realisation of the Government-Ordered Project - 6/15 MeV Accelerator. The realisation was accomplished in two stages: - stage I should result in deriving principal operational parameters of the accelerator - stage 2 will result in full implementation of the control system providing optimum control of the equipment and automatic maintaining of its parameters. Within the frames of the first stage, a klystron modulator panel was finished and the design documentation of the mechanical supporting structure, the arm, accelerating structure, collimator and control panel were advanced. Manufacturing of the above sub-units in the workshop has started. In the frames of the Specific Project of the State Committee for Scientific Research, the improvement of Neptun lOPC accelerator was undertaken. The read-out of the monitor dose with atmospheric pressure and ambient temperature compensation has been introduced. New filters for equalising the photon and electron beam and new wedge filters have been designed. Changes in programming have been introduced, which improve the patient's safety by eliminating possible personnel errors and increase the accuracy of radiation fields read-out. In 2000 ZdAJ progressed in development of the Quality System conforming EN-ISO 9001 Standard by including the provisions of EN 46001 Standard. The Standard EN 46001: ''Quality Systems - Medical Equipment''. Detailed requirements related to application of EN ISO 9001 is an European Quality Standard extending the provisions of EN ISO 9001 Standard over the manufacturers of medical equipment. (author)

  18. Installation for Studying the Scattering of Cold Neutrons; Installation pour l'etude de la diffusion des neutrons thermiques; Ustanovka dlya izucheniya rasseyaniya kholodnykh nejtronov; Instalacion para estudiar la dispersion de neutrones frios

    Energy Technology Data Exchange (ETDEWEB)

    Golikov, V V; Shapiro, F L; Shkatula, A; Yanik, E A [Ob' edinennyj institut yadernykh issledovanij, Dubna, Union of Soviet Socialist Republics (Russian Federation)

    1963-01-15

    Using the pulsed fut reactor in the Joint Institute for Nuclear Research, an installation was set up to investigate the spectrometry of cold neutrons. The moderator, adjoining the reactor reflector, and the beryllium filter were at the temperature of liquid nitrogen. The scatterer, located at a distance of about 0. 6 m from the moderator, was irradiated by flashes of cold neutrons, whose duration was determined by the lifetime of the neutrons in the moderator and the dispersion of the times-of-flight over a distance of 0. 6 m. The frequency of the flashes was 8/s. The steep beryllium edge of the spectrum, lying around 200 {mu}s, was used for spectrometry in the quasi-elastic range. The energy of the scattered neutrons was determined by the time-of-flight over the distance between scatterer and detector, which was about 10-40 m. ZnS + 10{sub 2}{sup 10} O{sub 3} scintillation detectors with surfaces of 300 and 2 000 cm{sup 2} were used and the efficiency, for fast neutrons, was about 60%. (author) [French] A l'aide du reacteur a flux pulse de neutrons rapides de l'Institut unifie de recherches nucleaires, les auteurs ont mis au point une installation pour la spectrometrie des neutrons thermiques. Le ralentisseur contigu au reflecteur du reacteur et le filtre deberyllium sont maintenus a la temperature de l'azote liquide. Le diffuseur, place a environ 60 cm du ralentisseur, est irradie par une bouffee de neutrons thermiques dont la duree est determinee par la vie moyenne des neutrons dans le ralentisseur et par l'etalement des temps de vol necessaires pour parcourir la distance de 60 cm. La frequence des bouffees est de 8/s. Pour la spectrometrie dans la region quasi-elastique, on utilise la bande en bordure du spectre qui correspond au beryllium et s'etale sur environ 200 {mu}s. L'energie des neutrons diffuses est determinee par la duree du parcours entre le diffuseur et le detecteur. Les auteurs ont utilise des detecteurs a scintillation a ZnS + 10{sub 2}{sup 10} O

  19. Reactor vital equipment determination techniques

    International Nuclear Information System (INIS)

    Bott, T.F.; Thomas, W.S.

    1983-01-01

    The Reactor Vital Equipment Determination Techniques program at the Los Alamos National Laboratory is discussed. The purpose of the program is to provide the Nuclear Regulatory Commission (NRC) with technical support in identifying vital areas at nuclear power plants using a fault-tree technique. A reexamination of some system modeling assumptions is being performed for the Vital Area Analysis Program. A short description of the vital area analysis and supporting research on modeling assumptions is presented. Perceptions of program modifications based on the research are outlined, and the status of high-priority research topics is discussed

  20. The replace repair decision for heavy equipment.

    Science.gov (United States)

    2004-01-01

    The fleet of equipment operated by the Virginia Department of Transportation (VDOT) constitutes a large investment, on the order of half a billion dollars. A means of identifying earlier and more accurately those pieces of equipment whose timely repl...

  1. Proceedings of FED remote maintenance equipment workshop

    International Nuclear Information System (INIS)

    Sager, P.; Garin, J.; Hager, E.R.; Spampinato, P.T.; Tobias, D.; Young, N.

    1981-11-01

    A workshop was convened in two sessions in January and March 1981, on the remote maintenance equipment for the Fusion Engineering Device (FED). The objectives of the first session were to familiarize the participants with the status of the design of the FED and to develop a remote maintenance equipment list for the FED. The objective of the second session was to have the participants present design concepts for the equipment which had been identified in the first session. The equipment list was developed for general purpose and special purpose equipment. The general purpose equipment was categorized as manipulators and other, while the special purpose equipment was subdivided according to the reactor subsystem it serviced: electrical, magnetic, and nuclear. Both mobile and fixed base manipulators were identified. Handling machines were identified as the major requirement for special purpose equipment

  2. Contribution to the study of thermal diffusion in isotopic mixtures of hydrogen; Contribution a l'etude de la diffusion thermique dans les melanges isotopiques de l'hydrogene

    Energy Technology Data Exchange (ETDEWEB)

    Lemarechal-Dupuis, A [Commissariat a l' Energie Atomique, 91 - Saclay (France). Centre d' Etudes Nucleaires

    1968-04-01

    Thermal diffusion constants of the mixtures H{sub 2}-HD and H{sub 2}-HT, where HD and HT were at trace concentrations, have been measured between 90 deg. K and 450 deg. K for H{sub 2}-HD and between 190 deg. K and 450 deg. K for H{sub 2}-HT, by using the elementary effect. Furthermore, the ratio of these constants has been measured by using a thermo-gravitational column of Clusius and Dickel, at temperatures of the hot wire between 455 deg. K and 1200 deg. K, the cold wall being at room temperature. Comparison with the predictions of existing theories shows that the Chapman-Enskog theory cannot account for the thermal diffusion of mixtures containing asymmetric molecules; the possible reasons for this disagreement are discussed. Our set of measurements, combined with the results of other authors, yields precise values at well defined conditions of temperature and concentration, useful for the determination of the coefficients of the semi-empirical expansion of Waldmann and Klemm. Furthermore some aspects of the column theory according to Furry and Jones have been tested. (author) [French] Les constantes de diffusion thermique des melanges H{sub 2}-HD et H{sub 2}-HT ou HD et HT figuraient, a l'etat de traces, ont ete mesurees a l'aide de l'effet elementaire entre 90 deg. K et 450 deg. K pour le melange H{sub 2}-HD,et entre 190 deg. K et 450 deg. K pour le melange H{sub 2}-HT. D'autre part, le rapport de ces constantes a ete mesure a l'aide d'une colonne de Clusius et Dickel pour des temperatures du fil chaud variant entre 455 deg. K et 1200 deg. K, la temperature de la paroi froide etant la temperature ambiante. La comparaison avec les predictions des theories existantes montre que la theorie de Chapman- Enskog ne peut rendre compte de la constante de diffusion thermique de melanges de molecules asymetriques; les raisons de ce desaccord sont discutees. L'ensemble de ces mesures, combine aux resultats d'autres auteurs, permet d'obtenir des valeurs precises dans des

  3. Irradiation and development of the nuclear emulsions exposed to intense fluxes of thermal neutrons with {gamma} rays; Irradiation et developpement des emulsions nucleaires exposees a des flux intenses de neutrons thermiques, accompagnes de rayons {gamma}

    Energy Technology Data Exchange (ETDEWEB)

    Faraggi, H.; Bonnet, A.; Cohen, J. [Commissariat a l' Energie Atomique, Lab. du Fort de Chatillon, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1952-07-01

    The thermal neutron fluxes provided by nuclear reactors permit the survey of relatively rare phenomenons, and dosage of very weak quantities of some elements. One of the most favorable detection technique are constituted by the use of the nuclear emulsions. one can mention: - the dosage of uranium by counting in the emulsion the number of traces due to fission fragments after irradiation. - The dosage of the lithium and the boron as trace amounts with the help of nuclear reactions (n, {alpha}) and thermal neutrons. - The research of reactions (n, {alpha}) or (n, p) of very weak cross section for middle or heavy elements. These different applications require however important neutrons fluxes. It had therefore obliged us to search for the most favorable irradiation and development of the emulsions conditions, to get the best visibility of the trajectories and decrease the phenomena of fog on the emulsion, which prevents any observation. (M.B.) [French] Les flux de neutrons thermiques fournis par les reacteurs nucleaires permettent l'etude de phenomenes relativement rares, et le dosage de tres faibles quantites de certains elements. Un des moyens de detection les plus favorables est constitue par l'utilisation des emulsions nucleaires. on peut citer: - le dosage de l'uranium par comptage dans l'emulsion du nombre de traces dues aux fragments de fission apres irradiation. - Le dosage du lithium et du bore a l'etat de traces a l'aide des reactions (n, {alpha}) sous l'action des neutrons thermiques. - La recherche de reactions (n,{alpha}) ou (n,p) de tres faible section efficace pour des elements moyens ou lourds. Ces differentes applications necessite cependant des flux de neutrons important. On a donc ete amene a rechercher les conditions les plus favorables d'irradiation et de developpement des emulsions, de maniere a obtenir la meilleure visibilite des trajectoires et diminuer les phenomenes de voile de l'emulsion, qui

  4. Musical Sound, Instruments, and Equipment

    Science.gov (United States)

    Photinos, Panos

    2017-12-01

    'Musical Sound, Instruments, and Equipment' offers a basic understanding of sound, musical instruments and music equipment, geared towards a general audience and non-science majors. The book begins with an introduction of the fundamental properties of sound waves, and the perception of the characteristics of sound. The relation between intensity and loudness, and the relation between frequency and pitch are discussed. The basics of propagation of sound waves, and the interaction of sound waves with objects and structures of various sizes are introduced. Standing waves, harmonics and resonance are explained in simple terms, using graphics that provide a visual understanding. The development is focused on musical instruments and acoustics. The construction of musical scales and the frequency relations are reviewed and applied in the description of musical instruments. The frequency spectrum of selected instruments is explored using freely available sound analysis software. Sound amplification and sound recording, including analog and digital approaches, are discussed in two separate chapters. The book concludes with a chapter on acoustics, the physical factors that affect the quality of the music experience, and practical ways to improve the acoustics at home or small recording studios. A brief technical section is provided at the end of each chapter, where the interested reader can find the relevant physics and sample calculations. These quantitative sections can be skipped without affecting the comprehension of the basic material. Questions are provided to test the reader's understanding of the material. Answers are given in the appendix.

  5. Concerning equipment procurement for NPPs

    International Nuclear Information System (INIS)

    Pana, N.

    2002-01-01

    After a stagnation in investments for nuclear power which extended over a period of 10-15 years, assessments done by energy forecast institutes, as well as, evaluations by UE institutions, OECD, and DOE (USA) point to the conclusion solid and argued that the electric energy of nuclear origin will record a new boost beginning probably with the year 2005. Particular efforts were concentrated upon improving the performances of existing plants and, on the other hand, towards new, evolutionary concepts in nuclear engineering. Advanced equipment for nuclear reactors and plants resulted and were already implemented. In Europe construction of both advanced PWR and BWR type reactors are underway. The paper consider the issues of Romanian nuclear power and presents the prospects for advanced CANDU reactors in connection with the Romania's infrastructure and necessities. The problem of modernizing the equipment and components for NPP is discussed in the context of financing and investment conditions. In conclusion, the share of nuclear power in Romania is expected to rise in order to compensate the decline in fossil fuel thermal power and to better solve the environmental issues

  6. Militärisch-Industrieller Komplex?

    DEFF Research Database (Denmark)

    Nørby, Søren

    2015-01-01

    Aufgedeckte Fehlentwicklungen und Missstände bei der Beschaffung von Rüstungsgütern für die Bundeswehr schrecken die deutsche Öffentlichkeit immer wieder – wenn auch nur kurzfristig – auf. Dabei werden in den Diskussionen häufig Argumentationsmuster und Begriffe aus der Zeit des Kalten Krieges...... verwendet, die auch damals schon nur bedingt der Realität entsprachen. So ist zum Beispiel der weithin bekannte Begriff des »Militärisch-Industriellen Komplexes« für die Verhältnisse in Deutschland bis zum heutigen Tag unpassend. Dennoch ist weder in der Geschichts-, noch in der Politik- oder in den...

  7. Equipment available for automating rig operations

    International Nuclear Information System (INIS)

    McNair, W.L.

    1990-01-01

    Several manufacturers are producing automated rig equipment, from complete systems to individual functions for existing drilling rigs. Significant improvements in well site time, costs of operations, and improved drilling performance have led drilling contractors to install this equipment on their rigs. This paper details some of the equipment available for automating rigs

  8. 13 CFR 143.32 - Equipment.

    Science.gov (United States)

    2010-01-01

    ... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Equipment. 143.32 Section 143.32...

  9. 32 CFR 33.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 32 National Defense 1 2010-07-01 2010-07-01 false Equipment. 33.32 Section 33.32 National Defense...

  10. 45 CFR 92.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 45 Public Welfare 1 2010-10-01 2010-10-01 false Equipment. 92.32 Section 92.32 Public Welfare...

  11. 40 CFR 31.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Equipment. 31.32 Section 31.32...

  12. 14 CFR 1273.32 - Equipment.

    Science.gov (United States)

    2010-01-01

    ... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Equipment. 1273.32 Section 1273.32...

  13. 29 CFR 1470.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 29 Labor 4 2010-07-01 2010-07-01 false Equipment. 1470.32 Section 1470.32 Labor Regulations...

  14. 15 CFR 24.32 - Equipment.

    Science.gov (United States)

    2010-01-01

    ... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Equipment. 24.32 Section 24.32...

  15. 38 CFR 43.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Equipment. 43.32 Section...

  16. 30 CFR 250.602 - Equipment movement.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Equipment movement. 250.602 Section 250.602... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Workover Operations § 250.602 Equipment movement. The movement of well-workover rigs and related equipment on and off a platform or from well to well on...

  17. 30 CFR 250.502 - Equipment movement.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Equipment movement. 250.502 Section 250.502... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Completion Operations § 250.502 Equipment movement. The movement of well-completion rigs and related equipment on and off a platform or from well to well...

  18. 46 CFR 121.220 - Cooking equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Cooking equipment. 121.220 Section 121.220 Shipping... SYSTEMS AND EQUIPMENT Cooking and Heating § 121.220 Cooking equipment. (a) Doors on a cooking appliance... cooking appliance must be installed to prevent movement in heavy seas. (c) For a grill or similar type of...

  19. 46 CFR 184.220 - Cooking equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Cooking equipment. 184.220 Section 184.220 Shipping...) VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Cooking and Heating § 184.220 Cooking equipment. (a) Doors on a cooking appliance must be provided with hinges and locking devices to prevent...

  20. Special equipment for etching nitrocellulose film

    International Nuclear Information System (INIS)

    Domanus, J.C.

    1983-08-01

    Nitrocellulose film and converter screens used for neutron radiography are described. Difficulties in visualization of radiographs on those films are mentioned. Because there is no equipment for etching nitrocellulose film available on the market Risoe has designed and produced such equipment at an estimated cost of Dkr. 15,000. Design criteria for this equipment are given and its performance described

  1. Developing equipment for AGR remote visual inspection

    International Nuclear Information System (INIS)

    James, P.W.; Walton, P.J.

    1985-01-01

    The Remote Inspection Group is part of the CEGB's Generation Development and Construction Division, and has responsibility for the design, development, procurement, testing and setting to work of the equipment provided to carry out routine remote visual inspections of its AGRs. This equipment includes both the viewing devices and the necessary placement equipment. (author)

  2. 46 CFR 121.210 - Heating equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Heating equipment. 121.210 Section 121.210 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... SYSTEMS AND EQUIPMENT Cooking and Heating § 121.210 Heating equipment. (a) Each heater must be so...

  3. 46 CFR 184.210 - Heating equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Heating equipment. 184.210 Section 184.210 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Cooking and Heating § 184.210 Heating equipment...

  4. Sample-related peripheral equipment at IPNS

    International Nuclear Information System (INIS)

    Bohringer, D.E.; Crawford, R.K.

    1985-01-01

    This paper describes samples environment equipment provided by IPNS to visiting users and staff scientists. Of the twelve horizontal neutron beam stations, (ten now operational, two under construction) all use one or more form of such support equipment. An in-house support group devotes a significant fraction of its time to development, calibration, and maintenance of this equipment

  5. 14 CFR 121.605 - Airplane equipment.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplane equipment. 121.605 Section 121.605..., FLAG, AND SUPPLEMENTAL OPERATIONS Dispatching and Flight Release Rules § 121.605 Airplane equipment. No person may dispatch or release an airplane unless it is airworthy and is equipped as prescribed in § 121...

  6. Fire prevention and protection for trackless equipment

    Energy Technology Data Exchange (ETDEWEB)

    Burger, A.J.

    1988-10-01

    With the increased use of trackless diesel and electrical equipment underground, the fire danger associated with this equipment has increased. The need for adequate fire prevention and protection on all aspects of trackless mechanised mining must be taken into consideration. This paper describes briefly the causes of fires on trackless equipment and the precautions taken to reduce the risk of ignition. 1 tab.

  7. Load Bearing Equipment for Bone and Muscle

    Science.gov (United States)

    Shackelford, Linda; Griffith, Bryan

    2015-01-01

    Resistance exercise on ISS has proven effective in maintaining bone mineral density and muscle mass. Exploration missions require exercise with similar high loads using equipment with less mass and volume and greater safety and reliability than resistance exercise equipment used on ISS (iRED, ARED, FWED). Load Bearing Equipment (LBE) uses each exercising person to create and control the load to the partner.

  8. Establishment for Nuclear Equipment -Overview

    International Nuclear Information System (INIS)

    Pracz, J.

    2006-01-01

    Research and development works conducted in the Establishment for Nuclear Equipment (ZdAJ) were focused around 3 subject areas: an accelerator for cancer treatment, therapeutical tables, systems and methods for controlling objects that cross international borders. The new, medium energy accelerator for cancer therapy cases is being designed in the Establishment for several years. In 2005 progress was achieved. A physical part, containing an electron beam has been completed and the parameters of that beam make it useful for therapeutical purposes. Consequently, the work on designing and testing of beam control systems, ensuring its high stability, repetition of irradiation parameters and accuracy of dosage have been started. Results of these tests make it very probable that 2006 will be the final year of scientific works and in 2007 the new apparatus will be ready for sales. Therapeutical tables have become a leading product of ZdAJ IPJ. Their technical parameters, reliability and universality in uses are appreciated by many customers of ZdAJ. In 2005, the table Polkam 16 was registered by the national Office for Registration of Medical Equipment as the first product of ZdAJ that meets all technical and formal requirements of the safety mark CE. This allows sales of the product on the market of the European Union. The research and development part of designing a therapeutical table for uses in the total body irradiation technique was also concluded in 2005. After the September 11 terrorist attacks on WTC a matter of controlling international borders have become a priority for many countries. In 2005 in ZdAJ IPJ, we conducted many preliminary calculations and experiments analyzing systems of irradiation sources, both photon and neutron as well as systems of detection and designing of signals triggered by controlling objects crossing the border. The results so far have enabled us to formulate a research project which has been positively evaluated by experts and found

  9. Communication equipment radiation resistance ensurance

    International Nuclear Information System (INIS)

    Myrova, L.O.; Chelizhenko, A.Z.

    1983-01-01

    A review of works on radiation resistance of electronic equipment (epsilon epsilon) for 15 years is presented. The effect of ionizing radiation appearing as a result of nuclear explosions in nuclear facilities and in outerspace on epsilon epsilon has been considered. Types of radiation effects in epsilon epsilon, radiation effect on semiconductor devices and integrated circUits, types of epsilon epsilon failures, as well as the procass of radiation-resistant epsilon epsilon designing and selection of its main parameters have been described. The methods of epsilon epsilon flowsheet optimization, application of mathematical simulation and peculiarities of ensurance of epsilon epsilon radiation resistance of communication systems are considered. Peculiarities of designing of radiation-resistant quartz generators, secondary power supply sources and amplifiers are discussed

  10. Purex: process and equipment performance

    International Nuclear Information System (INIS)

    Orth, D.A.

    1986-01-01

    The Purex process is the solvent extraction system that uses tributyl phosphate as the extractant for separating uranium and plutonium from irradiated reactor fuels. Since the first flowsheet was proposed at Oak Ridge National Laboratory in 1950, the process has endured for over 30 years with only minor modifications. The spread of the technology was rapid, and worldwide use or research on Purex-type processes was reported by the time of the 1955 Geneva Conference. The overall performance of the process has been so good that there are no serious contenders for replacing it soon. This paper presents: process description; equipment performance (mixer-settlers, pulse columns, rapid contactors); fission product decontamination; solvent effects (solvent degradation products); and partitioning of uranium and plutonium

  11. Automation of a thermogravimetric equipment

    International Nuclear Information System (INIS)

    Mussio, L.; Castiglioni, J.; Diano, W.

    1987-01-01

    A low cost automation of some instruments by means of simple electronic circuits and a microcomputer Apple IIe. type is discussed. The electronic circuits described are: a) a position detector including phototransistors connected as differential amplifier; b) a current source that, using the error signal of the position detector, changes the current through the coil of an electromagnetic balance to restore its zero position; c) a proportional temperature controller, zero volt switching to drive a furnace to a desired temperature; d) an interface temperature regulator-microcomputer to control the temperature regulator by software; e) a multiplexer for an analog input of a commercial interface. Those circuits are applied in a thermogravimetric equipment used also for vapours adsorption. A program in block diagram form is included and is able to record change of mass, time, furnace temperature and to drive the temperature regulator in order to have the heating rates or the temperature plateaux needed for the experiment. (author) [pt

  12. Establishment for Nuclear Equipment: Overview

    International Nuclear Information System (INIS)

    Pracz, J.

    2000-01-01

    Full text: The main objective of the activity of the Establishment for Nuclear Equipment (ZdAJ) in 1999 was to obtain the ISO 9001 certificate. Work on this problem has been successfully completed. The changes introduced in agreement with requirements of ISO in supervising the construction, manufacturing and servicing eliminate possible deficiencies of our products and will pay in the future. Two new important ventures have been undertaken: design of an accelerator with two photon energies and a reconstruction of simulator directed towards better geometrical parameters. The completion of the improvements in accelerator is foreseen for the year 2002. The changes comprise almost all sub-assemblies of the device. The modernized simulator will be installed in the hospital already in the year 2000 - the ameliorations concern mainly the arm of the apparatus, collimator, driving gears and control system. Of course - apart from this, the routine production activity of the Establishment was continued in 1999. (author)

  13. Protective equipment use among female rugby players.

    Science.gov (United States)

    Comstock, R Dawn; Fields, Sarah K; Knox, Christy L

    2005-07-01

    Our objective was to assess the prevalence of protective equipment use and the motivation for using protective equipment among a sample of US female rugby players. We surveyed a convenience sample of 234 current US female rugby players from 14 teams participating in a US women's rugby tournament, obtaining self-reported demographic, rugby exposure, and protective equipment use information. Mouthguards were the most commonly used piece of protective equipment: 90.8% of players reported having always worn a mouthguard while playing or practicing rugby within their most recent 3 months of play. Fewer than 15% of players reported having always worn other types of protective equipment. Equipment use varied by playing position. Whereas over 80% of players in all other positions always wore a mouthguard, 66.7% of scrum halves reported always wearing one. Both backs and forwards reported wearing shoulder pads, but only forwards reported always wearing padded headgear. Mouthguards, padded headgear, and shoulder pads were worn "to prevent injury," whereas ankle braces, neoprene sleeves, and athletic tape on joints were worn "to protect a current/recent injury." This is the first study of female rugby players to assess the prevalence of protective equipment use by playing position and the motivation for using protective equipment. With the exception of mouthguards, US female rugby players infrequently use protective equipment. Protective equipment use varies by playing position. Some types of protective equipment appear to be used as primary prevention mechanisms, whereas others are used as secondary or tertiary prevention mechanisms.

  14. Changing nature of equipment and parts qualification

    International Nuclear Information System (INIS)

    Bucci, R.M.

    1988-01-01

    Ideally, the original supplier of a piece of nuclear safety-related equipment has performed a qualification program and will continue to support that equipment throughout the lifetime of the nuclear power plants in which in equipment is installed. The supplier's nuclear quality assurance program will be maintained and he will continue to offer all necessary replacement parts. These parts will be identical to the original parts, certified to the original purchase order requirements, and the parts will be offered at competitive prices. Due to the changing nature of the nuclear plant equipment market, however, one or more of those ideal features are frequently unavailable when safety-related replacement equipment or parts are required. Thus, the process of equipment and parts qualification has had to adjust in order to ensure obtaining qualified replacements when needed. This paper presents some new directions taken in the qualification of replacement equipment and parts to meet changes in the marketplace

  15. Free-world microelectronic manufacturing equipment

    Science.gov (United States)

    Kilby, J. S.; Arnold, W. H.; Booth, W. T.; Cunningham, J. A.; Hutcheson, J. D.; Owen, R. W.; Runyan, W. R.; McKenney, Barbara L.; McGrain, Moira; Taub, Renee G.

    1988-12-01

    Equipment is examined and evaluated for the manufacture of microelectronic integrated circuit devices and sources for that equipment within the Free World. Equipment suitable for the following are examined: single-crystal silicon slice manufacturing and processing; required lithographic processes; wafer processing; device packaging; and test of digital integrated circuits. Availability of the equipment is also discussed, now and in the near future. Very adequate equipment for most stages of the integrated circuit manufacturing process is available from several sources, in different countries, although the best and most widely used versions of most manufacturing equipment are made in the United States or Japan. There is also an active market in used equipment, suitable for manufacture of capable integrated circuits with performance somewhat short of the present state of the art.

  16. Energy consumption and management in metal heat treatment implementation; Consommation et gestion d`energie dans la mise en oeuvre des traitements thermiques des metaux

    Energy Technology Data Exchange (ETDEWEB)

    Leroux, C. [Vide et Traitements Services, 92 - Gennevilliers (France)

    1996-12-31

    Energy management in the metal heat treatment sector, where thermal efficiency is generally poor, is based on an adequate power supply contract with utilities, a thorough evaluation of energy consumption from the various equipment, and systems for the limitation of energy consumption: warning signals when the contracted power is to be reached, power cut-off systems or intelligent cut-off/restart systems and global load management. For gas appliances, heat recovery combustors may be a solution

  17. 9 CFR 590.502 - Equipment and utensils; PCB-containing equipment.

    Science.gov (United States)

    2010-01-01

    ... Sanitary Standards and accepted practices currently in effect for such equipment. (c) New or replacement equipment or machinery (including any replacement parts) brought onto the premises of any official plant... equipment and machinery, and any replacement parts for such equipment and machinery. Totally enclosed...

  18. Improvement of the heat exchanges by application of an electric field in the boiling freon 12; Amelioration des echanges thermiques par application d'un champ electrique dans le freon 12 bouillant

    Energy Technology Data Exchange (ETDEWEB)

    Bonjour, Emmanuel; Verdier, Jacques; Weil, Louis [Commissariat a l' energie atomique et aux energies alternatives - CEA, Centre d' Etudes Nucleaires de Grenoble (France)

    1960-07-01

    lt was already known that the heat exchanges by simple convection are considerably improved by the application of an electric field, but no study about the effect of this field when there is ebullition has been issued until now. The authors indicate the result of their experimental investigations which present a very great interest for the increase of the efficiency of the refrigeration cycles. Reprint of a paper published in Revue generale du froid, Sep 1960 [French] On savait deja qu'il etait possible d'ameliorer sensiblement les echanges thermiques dus a la simple convection par l'application d'un champ electrique, mais jusqu'a present, il n'existait pas de resultats concernant l'effet de ce champ en presence d'ebullition. Les auteurs indiquent les resultats de leur investigation experimentale qui presente un tres grand interet pour l'accroissement de l'efficacite du cycle de refrigeration. Reproduction d'un article publie dans Revue generale du froid, Sep 1960.

  19. Calculation of the thermal utilisation factor in a cell made up of a given number of concentric media; Calcul du facteur d'utilisation thermique dans une cellule formee d'un nombre quelconque de milieux concentriques

    Energy Technology Data Exchange (ETDEWEB)

    Amouyal, A; Benoist, P; Guionnet, Ch [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-07-01

    The method of calculating the thermal utilisation factor, described in a previous report, is extended to the case of a cylindrical cell containing a given number of concentric media, certain of which may be empty. A collision by collision method is used in all but the peripheral medium, which may be treated by a theory of controlled diffusion. A programme for the IBM 650 calculator has been based on this method. Some numerical results are presented. An equivalent matrix formulation, due to C. Guionnet, is given as an appendix. (author) [French] La methode de calcul du facteur d'utilisation thermique, exposee dans un rapport precedent, est etendue au cas d'une cellule cylindrique comportant un nombre quelconque de milieux concentriques, certains de ces milieux pouvant etre vides. On utilise une methode choc par choc dans tous les milieux excepte le milieu peripherique qui peut etre traite par une theorie de diffusion ajustee. La methode a fait l'objet d'un programme pour le calculateur IBM 650. Quelques resultats numeriques sont presentes. Une formulation matricielle equivalente, due a C. Guionnet, est exposee en annexe. (auteur)

  20. Contribution to the study of recoil species produced by potassium ferrocyanide neutron irradiation; Contribution a l'etude de la reactivite des especes de recul dans le ferrocyanure de potassium irradie aux neutrons thermiques

    Energy Technology Data Exchange (ETDEWEB)

    Meriadec Vernier de Byans, B. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-04-01

    The chemical species produced by potassium ferrocyanide neutron irradiation were separated and identified. The study of their behaviour upon thermal annealing has allowed to establish a scheme of reaction as well as a kinetic treatment of the data. Activation energies are determined in different conditions and the effects of radiation dose, oxygen and water of crystallisation upon the activation energies were studied. Preliminary E.S.R. data and its relevance to the decomposition process is also discussed. (authors) [French] On a separe et identifie les differentes especes chimiques produites par irradiation neutronique de ferrocyanure de potassium. L'etude de leur comportement au cours du recuit thermique a permis l'application de differentes cinetiques et l'etablissement d'un schema de reaction. On a deterrmine la valeur des energies d'activation dans differentes conditions de recuit ainsi que l'influence de la dose de radiations, de l'oxygene et de l'eau de cristallisation sur ces energies. Une serie de mesures de resonance paramagnetique electronique a complete cette etude. (auteurs)

  1. Determination of the mean free path of the thermal neutrons transport by the measure of a complex diffusion length; Determination du libre parcours moyen de transport des neutrons thermiques par la mesure d'une longueur de diffusion complexe

    Energy Technology Data Exchange (ETDEWEB)

    Raievski, V; Horowitz, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    The further method is the outcome of a technique used in the study of neutrons in scattering and slowing-down environment. In this technique, we replace the constant sources used in the classic experiences by modulated sources with a variable frequency. The object of this article is to describe the extension of the method for the mean free path for transport of thermal neutrons and also to indicate the possible applications for other sizes, as the slowing length, or the absolute value of the cross-section of the boron. (M.B.) [French] La methode qui va etre decrite est l'aboutissement d'une technique utilisee dans l'etude des milieux ou diffusent et se ralentissent des neutrons. Dans cette technique, on remplace les sources constantes utilisees dans les experiences classiques par des sources modulees, a frequence variable. L'objet de cet article est de decrire l'extension de la methode a la mesure du libre parcours moyen de transport des neutrons thermiques et egalement d'indiquer les applications possibles a la mesure d'autres grandeurs, telles que la longueur de ralentissement, ou la valeur absolue de la section de capture du bore. (M.B.)

  2. Industrial Ultrasonic Inspection of Stainless-Steel Claddings for the EL4 Reactor; Controle Industriel par Ultrasons des Gaines en Acier Inoxydable du Reacteur EL4; Promyshlennyj kontrol' obolochechnykh trub iz nerzhaveyushchej stali reaktora dlya EL4 s pomoshch'yu ul'trazvukovogo metoda; Metodos Ultrasonicos para Control Industrial de las Vainas de Acero Inoxidable del Reactor EL4

    Energy Technology Data Exchange (ETDEWEB)

    Prot, A. C.; Foulquoer, H. E.; Peyrot, J. P. [Centre d' Etudes Nucleaires de Saclay (France)

    1965-09-15

    Improved reactor performance requires the use of accurately fabricated and carefully inspected components. One inspection relates to the quality of the cladding tubes, whose mechanical reliability is essential for economic reactor operation. The choice and development of a method is a difficult matter and the authors explain the main factors involved. Once the choice has been made and the method has been developed in the laboratory, two new problems arise: Adaptation to meet industrial requirements; and The need to reconcile the quality standards attainable with the manufacturing process at any given stage and the somewhat arbitrarily defined specifications for the finished product. In practice, this involves a statistical study of batches of tubes from various sources and their classification in relation to more or less strict thresholds. The number of tubes which have to be inspected is much larger than originally expected. This has led to the design of an automatic inspection device geared both to the output rates involved and to the requirements of the type of inspection adopted; the latter are generally mechanical and impose particularly careful product fabrication. These various characteristics are now embodied in a device whose capacity can already easily meet the requirements of a fuel-element production line. The potentialities of the device are closely dependent on the characteristics of the inspection equipment used, especially the performances of the electronic part of ultrasonic inspection instruments and of the transducers. This study shows that standard equipment is not very suitable and that immediate thought should be given to special instruments for this type of inspection. (author) [French] L'accroissement des performances des reacteurs necessite l'utilisation de materiaux finement elabores et soigneusement controles. L'un des aspects de ce controle est celui de la qualite des tubes de gainage utilises, dont la tenue mecanique est un facteur

  3. Etude par Spectrométrie de masse de la décomposition thermique sous vide de kérogènes appartenant à deux lignées évolutives distinctes Mass Spectrometry Investigation of the Vaccum Thermal Decomposition of Kerogens from Two Distinct Evolutive Lines

    Directory of Open Access Journals (Sweden)

    Souron C.

    2006-11-01

    Full Text Available Le but de cette étude est la connaissance qualitative et quantitative des composés dégagés lors de la décomposition thermique sous vide de quelques échantillons de kérogènes appartenant à deux lignées différentes. La principale technique utilisée est la spectrométrie de masse, appuyée sur des études préliminaires par thermogravi métrie et analyse élémentaire. Une adaptation particulière de l'appareillage et une mise au point de la méthode d'étalonnage permettent de doser les quatre composés minéraux les plus abondants et de donner une représentation des composés organiques. Cette étude montre que les composés formés au cours du chauffage comprennent, pour tous les kérogènes étudiés, des composés oxygénés et soufrés (CO, H2O, SH2, SOJ libérés principalement dans l'intervalle de température 200-400° C, et des composés hydrocarbonés, plus abondants, dans l'intervalle 300-500° C. On commente dans cet article l'origine supposée de ces composés; la formation de S02 au cours de la pyrolyse est particulièrement mal connue. On remarque que le rapport H2O/C02 peut être un critère de distinction des deux lignées de kérogènes étudiés. La distinction observée sur les produits hydrocarbonés nécessitera des recherches complémentaires pour être utilisée avec plus de sûreté. The aim of this investigation is to obtain a qualitative and quantitative understanding of the compounds given off during the vacuum thermal decomposition of several kerogen samples from two different lines. The main technique used is mass spectrometry, based on prior investigations by thermogravimetry and element onalysis. The equipment was specially adapted and a calibration method was developed for titrating the four most abundant minerai compounds and for representing the organic compounds. This investigation shows that the compounds formed during heating include, for oil the kerogens examined, oxygen-and sulfur

  4. Quality assurance for radiodiagnostic equipment in Uruguay

    International Nuclear Information System (INIS)

    Cotelo, Elena D.

    2001-01-01

    Since Uruguay did not have an study on X-ray equipment, students of Radiation Protection course (RP) made this field work throughout the country. The objective is to obtain information on the number and kind of X-ray radiodiagnostic equipment. Some of the results are: there are 666 radiodiagnostic equipment. The ratio of population to equipment is 4.515 to 1 in the capital and the mean rate in the rest of the country is 4.383 to one, with a minimum of 1.707 and a maximum of 8.220. The Public Health Ministry (MSP) and the Instituciones de Asistencia Medica Colectiva (a kind of private heath assurance) (IAMC) have less equipment in the capital than in the rest of the country. The 37% of the capital population receives assistance through the IAMC , with a 42.5 % of the equipment. Uruguay except the capital has 18 districts and 17 computed tomography equipment, from which only 3 belong to the MSP. Five districts do not have any. In Montevideo, there are 11.500 females over forty years of age per X-ray mammography equipment, and this relation in the rest of the country is 13.900. There are 21 X-ray Interventional radiology equipment, 16 of them are in the capital. Is from relating the radiodiagnostic equipment, the population and the procedures, that quality assistance indicators emerge. This owns high importance on the way to create a RP National Programme. (author)

  5. Maintenance program guidelines for programmatic equipment

    International Nuclear Information System (INIS)

    1994-11-01

    The Division Directors at Lawrence Berkeley Laboratory are responsible for implementing a maintenance program for research equipment (also referred to as programmatic equipment) assigned to them. The program must allow maintenance to be accomplished in a manner that promotes operational safety, environmental protection and compliance, and cost effectiveness; that preserves the intended functions of the facilities and equipment; and that supports the programmatic mission of the Laboratory. Programmatic equipment -- such as accelerators, lasers, radiation detection equipment, and glove boxes -- is dedicated specifically to research. Installed equipment, by contrast, includes the mechanical and electrical systems installed as part of basic building construction, equipment essential to the normal functioning of the facility and its intended use. Examples of installed equipment are heating, ventilating, and air conditioning systems; elevators; and communications systems. The LBL Operating and Assurance Program Plan (PUB-3111, Revision 4) requires that a maintenance program be prepared for programmatic equipment and defines the basic maintenance program elements. Such a program of regular, documented maintenance is vital to the safety and quality of research activities. As a part of that support, this document offers guidance to Laboratory organizations for developing their maintenance programs. It clarifies the maintenance requirements of the Operating and Assurance Program (OAP) and presents an approach that, while not the only possibility, can be expected to produce an effective maintenance program for research equipment belonging to the Laboratory's organizations

  6. Inspection device for buried equipment

    International Nuclear Information System (INIS)

    Hanawa, Jun.

    1994-01-01

    In an inspection device for a buried equipment, a rail is suspended at the upper portion of a vessel of a pit-vessel type pump buried in a plant building floor, and a truck movable vertical in the vessel along the rail, and an ultrasonic wave probe contained in the truck and urged to the vessel by an electromagnet are disposed. In addition, an elevator moving vertically along a shaft is disposed, and an arm having the ultrasonic probe disposed at the end portion and driven by a piston are disposed to the elevator. The ultrasonic wave probe moves vertically together with the truck along the rail in the vessel while being urged to the vessel by the electromagnet to inspect and measure the state at the inner and outer surfaces of the vessel. Further, the length of the arm is controlled so as to set a predetermined distance between the ultrasonic wave probe and the vessel. Subsequently, the elevator is moved vertically along a shaft passing through a shaft hole of a mount, and the shaft is rotated thereby enabling to inspect and measure the state of the inner and outer surfaces of the vessel. (N.H.)

  7. Equipment used in nuclear medicine

    International Nuclear Information System (INIS)

    Das, B.K.; Noreen Norfaraheen Lee Abdullah

    2012-01-01

    Detection of radiation is the common purpose of all equipment's and instruments used in radioisotope laboratories. The first and most important instrument that was used in nuclear medicine was Geiger tube developed by H.W. Geiger as early in 1908. He in association with Mueller developed the so called Geiger-Muller tube (GM tube) which could be used to detect beta and gamma radiations. In spite of its severe limitations, GM tube remained the only external counting device until 1949. In 1948, Kallman reported that the scintillations can be detected and amplified with the help of photomultiplier tubes (PMTs). In comparison with gas filled detectors, scintillation detectors have two principal advantages that augment their use in nuclear medicine. Firstly, they are capable of much higher counting rates because of fast resolving times and secondly, because they are much more efficient for gamma ray detection. The scintillation detector is the most basic block of any modern radioisotope detection instrument like rate meter, counter, scanner, gamma camera or single photon emission computed tomography. (author)

  8. Ageing management and equipment qualification

    International Nuclear Information System (INIS)

    Stahl, Gunnar

    2014-01-01

    The knowledge of how the environment and load of organic material in general and especially polymers and lubricants, is affecting the degradation of important properties, have increased during the last decade. However the restrictions using established additives like some color pigments due to their poisonousness e.g. pigments based at cadmium, lead, mercury etc. have caused problems when replacing additives to polymers. The replacement additives have often been used in new design without going through the required material qualification procedure. There have also been observed that some non-qualified and non-approved materials have been installed in some power plants due to false documentation. There are also a lot of new manufacturers, of materials similar to the previously qualified materials, active at the market. This increases the difficulty to ensure that the required material quality is used. New materials, new additives and new manufacturers makes if more and more difficult to assure that the expected material is present. This causes more strict demands of how the new materials often used in equipment at type-testing and in replacement materials are analyzed and documented. By implementing new steps for chemical, mechanical and electrical analysis and increase the general quality assurance content this issue can be managed. (authors)

  9. Equipment selection for atmospheric drying

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, P D; Bhattacharyya, S [Nuclear Power Corporation, Bhabha Atomic Research Centre, Mumbai (India)

    1994-06-01

    Heavy water management is a major factor in deciding the economics of the PHWRs. Hence it is necessary to have an efficient recovery system, for the heavy water vapour escaping from various process systems and maintain a dry atmosphere in the recovery areas. While the basic objective of the atmospheric drying system is to maximize recovery and to minimize stack losses, it is equally important to optimally design the system with due consideration to operational and maintenance aspects. At present, heavy water vapour recovery in the existing Nuclear Power Plants (NPPs) is carried out by dryers of dual fixed bed design. While moving bed design could have some advantages, this has not been adopted so far because of the cumbersome mechanical design involved and special requirements for nuclear application. Developmental work done in this direction has resulted in compact alternative designs. In one of the designs, the change over from adsorption to regeneration is achieved by rotating the bed slowly. This concept is further refined in another alternative using a dessicant wheel. This paper contains brief equipment description of different designs; enumerates the design requirements of an atmospheric drying system for reactor building; describes steps for designing fixed bed type D{sub 2}O vapour recovery system, and highlights advances in dryer technology. (author). 2 refs., 4 figs., 1 ill.

  10. Materials division facilities and equipment

    International Nuclear Information System (INIS)

    Biest, O. v.d.

    1984-01-01

    The research activities of the Division at the Petten Establishment have the aims of characterising the properties of high temperature materials in industrial process environments and of understanding the structures involved in order to gain an insight into behavioural mechanisms. Metallic materials fall within the scope of the programme; the activities are, at present, almost entirely concerned with austenitic steels and nickel based alloys. Starting in 1984, advanced ceramic materials will be studied as well. The equipment available permits the study of mechanical properties in controlled gaseous environments, of the rates and mechanisms of corrosive reactions between materials and those environments, and of the surface and bulk structures by advanced physical techniques. Special preparation and treatment techniques are available. The Division has developed a Data Bank on high temperature alloys. It also operates an information Centre, the activities of which include the organisation of scientific meetings, the commissioning of ''state of the art'' studies on topics in the field of high temperature materials and their applications and the development of a inventory of current research activities in the field in Europe. This booklet is intended to present the facilities and services of the Division to the organizations which are interested in its programmes of work

  11. ISS qualified thermal carrier equipment

    Science.gov (United States)

    Deuser, Mark S.; Vellinger, John C.; Jennings, Wm. M.

    2000-01-01

    Biotechnology is undergoing a period of rapid and sustained growth, a trend which is expected to continue as the general population ages and as new medical treatments and products are conceived. As pharmaceutical and biomedical companies continue to search for improved methods of production and, for answers to basic research questions, they will seek out new avenues of research. Space processing on the International Space Station (ISS) offers such an opportunity! Space is rapidly becoming an industrial laboratory for biotechnology research and processing. Space bioprocessing offers exciting possibilities for developing new pharmaceuticals and medical treatments, which can be used to benefit mankind on Earth. It also represents a new economic frontier for the private sector. For over eight years, the thermal carrier development team at SHOT has been working with government and commercial sector scientists who are conducting microgravity experiments that require thermal control. SHOT realized several years ago that the hardware currently being used for microgravity thermal control was becoming obsolete. It is likely that the government, academic, and industrial bioscience community members could utilize SHOT's hardware as a replacement to their current microgravity thermal carrier equipment. Moreover, SHOT is aware of several international scientists interested in utilizing our space qualified thermal carrier. SHOT's economic financing concept could be extremely beneficial to the international participant, while providing a source of geographic return for their particular region. Beginning in 2000, flight qualified thermal carriers are expected to be available to both the private and government sectors. .

  12. Diagnostics of Electric Equipment Windings

    Directory of Open Access Journals (Sweden)

    I. I. Branovitsky

    2007-01-01

    Full Text Available The paper presents methodology and results of the investigations pertaining to study of influence of short-circuited turns on transient electrical processes in electric motor windings. Dependence of their damped speed and value of the difference signal, obtained at reciprocal subtraction of damped oscillation curves in absence and in presence of short-circuited turns, on number of turns in the tested windings. It has been determined that damped oscillation curves, immediately attributed to short-circuited turns, have peak values along temporary axis which are areas of the largest transient process sensitivity to КЗ turns.Methodology for diagnostics of single- and three-phase electric motor windings and also other electric equipment, being realized in DO-1 device, has been developed in the paper. The men­tioned device makes it possible to carry out visual comparison and quantitative analysis of damped oscillation curves in the tested windings with standard ones which are set in the device memory and their difference signals.

  13. WP EMPLACEMENT CONTROL AND COMMUNICATION EQUIPMENT DESCRIPTIONS

    International Nuclear Information System (INIS)

    Raczka, N.T.

    1997-01-01

    The objective and scope of this document are to list and briefly describe the major control and communication equipment necessary for waste package emplacement at the proposed nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the required equipment are explained and summarized in the individual subsections of this document. This task was evaluated in accordance with QAP-2-0 and found not to be quality affecting. Therefore, this document was prepared in accordance with NAP-MG-012. The following control and communication equipment are addressed in this document: (1) Programmable Logic Controllers (PLC's); (2) Leaky Feeder Radio Frequency Communication Equipment; (3) Slotted Microwave guide Communication Equipment; (4) Vision Systems; (5) Radio Control Equipment; and (6) Enclosure Cooling Systems

  14. Procurement strategic analysis of nuclear safety equipment

    International Nuclear Information System (INIS)

    Wu Caixia; Yang Haifeng; Li Xiaoyang; Li Shixin

    2013-01-01

    The nuclear power development plan in China puts forward a challenge on procurement of nuclear safety equipment. Based on the characteristics of the procurement of nuclear safety equipment, requirements are raised for procurement process, including further clarification of equipment technical specification, establishment and improvement of the expert database of the nuclear power industry, adoption of more reasonable evaluation method and establishment of a unified platform for nuclear power plants to procure nuclear safety equipment. This paper makes recommendation of procurement strategy for nuclear power production enterprises from following aspects, making a plan of procurement progress, dividing procurement packages rationally, establishing supplier database through qualification review and implementing classified management, promoting localization process of key equipment continually and further improving the system and mechanism of procurement of nuclear safety equipment. (authors)

  15. Improved servicing equipment for steam generators

    International Nuclear Information System (INIS)

    Hedtke, James C.

    1998-01-01

    To help keep personnel exposure as low as reasonably achievable and reduce critical path outage time, most nuclear plants of PWR design in the USA are now using improved equipment to service their steam generators (SGs) during outages. Because of the success of this equipment in the USA, two Belgian plants and one English plant have purchased this equipment, and other nuclear plants in Europe are also considering procurement. The improved SG servicing equipment discussed in this paper discusses consists of nozzle dams, segmented multi-stud tensioner, primary manway cover handling tool set, shield door and fastener cleaner. This equipment is specifically designed for the individual plant application and can also be specified for replacement SG projects. All of the equipment can be used without modification of the existing SGs. (author)

  16. Preparation of alternate fuels by means of bio-methanization, pyrolysis and gasification; Preparation thermique de combustibles alternatifs par bio-methanisation, thermolyse et gazeification

    Energy Technology Data Exchange (ETDEWEB)

    Fontana, A.; Jung, C.G. [Universite Libre de Bruxelles (Belgium)

    2003-06-01

    The paper gives a general description of wastes and their various components each of them depending on their behaviour during the beneficiation treatment: water, organic matters (bio-degradable and non bio-degradable), mineral matters and metals some examples are given. Various processes are available: compost production, bio-methanization and thermal processes. These thermal processes are incineration, gasification and pyrolysis, depending on the quantity (or absence) of air during the process. The paper gives a description of these processes as well as the type of equipment that are utilised. (authors)

  17. Equipment Replacement Decision Making: Opportunities and Challenges

    OpenAIRE

    Fan, Wei (David); Gemar, Mason D.; Machemehl, Randy

    2012-01-01

    The primary function of equipment managers is to replace the right equipment at the right time and at the lowest overall cost. In this paper, the opportunities and challenges associated with equipment replacement optimization (ERO) are discussed in detail. First, a comprehensive review of the state-of-the art and state-of-the practice literature for the ERO problem is conducted. Second, a dynamic programming (DP) based optimization solution methodology is presented to solve the ERO problem. T...

  18. History and development of the tennis equipment

    OpenAIRE

    Horáková, Kateřina

    2007-01-01

    Title: History and development of the tennis equipment. Aim of the work: Process an integral, tabular and synoptic historical development overview of the tennis equipment. This owerview will cover the period since the early beginnings of the game to present days. Methods: Advance work has historical charakter therefore used methods are historiogaphical methods such as chronological method and historical method. Results: Produce tabular description of the tennis equipment by means of reading a...

  19. Mine railway equipments management information system

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X.; Han, K.; Duan, T.; Liu, Z.; Lu, H. [China University of Mining and Technology, Xuzhou (China)

    2007-06-15

    Based on client/server and browser/server models, the management information system described realized the entire life-cycle management of mine railway equipment which included universal equipment and special equipment in the locomotive depot, track maintenance division, electrical depot and car depot. The system has other online functions such as transmitting reports, graphics management, statistics, searches, graphics wizard and web propaganda. It was applied in Pingdingshan Coal Co. Ltd.'s Railway Transport Department. 5 refs., 4 figs.

  20. Aircraft Wiring Support Equipment Integration Laboratory (AWSEIL)

    Data.gov (United States)

    Federal Laboratory Consortium — Purpose:The Aircraft Wiring Support Equipment Integration Laboratory (AWSEIL) provides a variety of research, design engineering and prototype fabrication services...

  1. Making petroleum equipment safe, a priority

    International Nuclear Information System (INIS)

    1999-01-01

    Changes to the 'Act respecting the use of petroleum products' have been announced effective May 1, 1999. The changes have been made to reduce problems which can be attributed to petroleum product leaks. The new regulations will make owners and users of petroleum equipment, including underground and above-ground storage equipment and commercial storage tanks, more accountable for the use of their own equipment. The emphasis in the new regulations is based upon the storage capacity of petroleum equipment and the risks associated with this equipment, rather than the on the activities of the owners concerned. Accordingly, the new regulations call for stricter requirements for high-risk equipment, a private equipment inspection plan, a two-year operating permit, replacing the current permits and certificates, a tariff structure based on the risks associated with the equipment, and deregulation of commercial activities involving petroleum products that require no equipment. Additionally, the amendments to the Act transfer responsibility for administration to the Regie du batiment and to the Ministere des Transports. Details of each of these changes are explained

  2. Utility equipment systems: promising more for less

    Energy Technology Data Exchange (ETDEWEB)

    1987-10-01

    This paper discusses current developments in utility equipment systems, a term applied to carrier vehicles, mostly evolved from well-known forms of construction or mining equipment modified to work with a variety of different front or back end attachments. One of the equipment ranges discussed is the Normet cassette system produced by the Orion corporation of Finland, which allows a basic chassis to be converted from a personnel carrier to an ANFO carrier within minutes. LHD vehicles which are being adapted to fulfil multipurpose roles, such as carrying roof supports, chocks and other heavy mining equipment underground are also discussed. 5 figs.

  3. Detection of Equipment Faults Before Beam Loss

    CERN Document Server

    Galambos, J.

    2016-01-01

    High-power hadron accelerators have strict limits on fractional beam loss. In principle, once a high-quality beam is set up in an acceptable state, beam loss should remain steady. However, in practice, there are many trips in operational machines, owing to excessive beam loss. This paper deals with monitoring equipment health to identify precursor signals that indicate an issue with equipment that will lead to unacceptable beam loss. To this end, a variety of equipment and beam signal measurements are described. In particular, several operational examples from the Spallation Neutron Source (SNS) of deteriorating equipment functionality leading to beam loss are reported.

  4. 21 CFR 866.4500 - Immunoelectrophoresis equipment.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents... clinical use with its electrical power supply is a device used for separating protein molecules...

  5. PROMSYS, Plant Equipment Maintenance and Inspection Scheduling

    International Nuclear Information System (INIS)

    Morgan, D.L.; Srite, B.E.

    1986-01-01

    1 - Description of problem or function: PROMSYS is a computer system designed to automate the scheduling of routine maintenance and inspection of plant equipment. This 'programmed maintenance' provides the detailed planning and accomplishment of lubrication, inspection, and similar repetitive maintenance activities which can be scheduled at specified predetermined intervals throughout the year. The equipment items included are the typical pumps, blowers, motors, compressors, automotive equipment, refrigeration units, filtering systems, machine shop equipment, cranes, elevators, motor-generator sets, and electrical switchgear found throughout industry, as well as cell ventilation, shielding, containment, and material handling equipment unique to nuclear research and development facilities. Four related programs are used to produce sorted schedule lists, delinquent work lists, and optional master lists. Five additional programs are used to create and maintain records of all scheduled and unscheduled maintenance history. 2 - Method of solution: Service specifications and frequency are established and stored. The computer program reviews schedules weekly and prints, on schedule cards, instructions for service that is due the following week. The basic output from the computer program comes in two forms: programmed-maintenance schedule cards and programmed-maintenance data sheets. The data sheets can be issued in numerical building, route, and location number sequence as equipment lists, grouped for work assigned to a particular foreman as the foreman's equipment list, or grouped by work charged to a particular work order as the work-order list. Data sheets grouped by equipment classification are called the equipment classification list

  6. Equipment Reliability Process in Krsko NPP

    International Nuclear Information System (INIS)

    Gluhak, M.

    2016-01-01

    To ensure long-term safe and reliable plant operation, equipment operability and availability must also be ensured by setting a group of processes to be established within the nuclear power plant. Equipment reliability process represents the integration and coordination of important equipment reliability activities into one process, which enables equipment performance and condition monitoring, preventive maintenance activities development, implementation and optimization, continuous improvement of the processes and long term planning. The initiative for introducing systematic approach for equipment reliability assuring came from US nuclear industry guided by INPO (Institute of Nuclear Power Operations) and by participation of several US nuclear utilities. As a result of the initiative, first edition of INPO document AP-913, 'Equipment Reliability Process Description' was issued and it became a basic document for implementation of equipment reliability process for the whole nuclear industry. The scope of equipment reliability process in Krsko NPP consists of following programs: equipment criticality classification, preventive maintenance program, corrective action program, system health reports and long-term investment plan. By implementation, supervision and continuous improvement of those programs, guided by more than thirty years of operating experience, Krsko NPP will continue to be on a track of safe and reliable operation until the end of prolonged life time. (author).

  7. Additional Equipment for Soil Biodegradation

    Science.gov (United States)

    Vondráčková, Terezie; Kraus, Michal; Šál, Jiří

    2017-12-01

    Intensification of industrial production, increasing citizens’ living standards, expanding the consumer assortment mean in the production - consumption cycle a constantly increasing occurrence of waste material, which by its very nature must be considered as a source of useful raw materials in all branches of human activity. In addition to strict legislative requirements, a number of circumstances characterize waste management. It is mainly extensive transport associated with the handling and storage of large volumes of substances with a large assortment of materials (substances of all possible physical and chemical properties) and high demands on reliability and time coordination of follow-up processes. Considerable differences in transport distances, a large number of sources, processors and customers, and not least seasonal fluctuations in waste and strong price pressures cannot be overlooked. This highlights the importance of logistics in waste management. Soils that are contaminated with oil and petroleum products are hazardous industrial waste. Methods of industrial waste disposal are landfilling, biological processes, thermal processes and physical and chemical methods. The paper focuses on the possibilities of degradation of oil pollution, in particular biodegradation by bacteria, which is relatively low-cost among technologies. It is necessary to win the fight with time so that no ground water is contaminated. We have developed two additional devices to help reduce oil accident of smaller ranges. In the case of such an oil accident, it is necessary to carry out the permeability test of contaminated soil in time and, on this basis, to choose the technology appropriate to the accident - either in-sit biodegradation - at the site of the accident, or on-sit - to remove the soil and biodegrade it on the designated deposits. A special injection drill was developed for in-sit biodegradation, tossing and aeration equipment of the extracted soil was developed for

  8. Lunar construction/mining equipment

    Science.gov (United States)

    Ozdemir, Levent

    1990-01-01

    For centuries, mining has utilized drill and blast as the primary method of rock excavation. Although this technique has undergone significant improvements, it still remains a cyclic, labor intensive operation with inherent safety hazards. Other drawbacks include damage to the surrounding ground, creation of blast vibrations, rough excavation walls resulting in increased ventilation requirements, and the lack of selective mining ability. Perhaps the most important shortcoming of drill and blast is that it is not conducive to full implementation of automation or robotics technologies. Numerous attempts have been made in the past to automate drill and blast operations to remove personnel from the hazardous work environment. Although most of the concepts devised look promising on paper, none of them was found workable on a sustained production basis. In particular, the problem of serious damage to equipment during the blasting cycle could not be resolved regardless of the amount of charge used in excavation. Since drill and blast is not capable of meeting the requirements of a fully automated rock fragmentation method, its role is bound to gradually decrease. Mechanical excavation, in contrast, is highly suitable to automation because it is a continuous process and does not involve any explosives. Many of the basic principles and trends controlling the design of an earth-based mechanical excavator will hold in an extraterrestrial environment such as on the lunar surface. However, the economic and physical limitations for transporting materials to space will require major rethinking of these machines. In concept, then, a lunar mechanical excavator will look and perform significantly different from one designed for use here on earth. This viewgraph presentation gives an overview of such mechanical excavator systems.

  9. Considerations concerning the reliability of reactor safety equipment; Considerations sur la fiabilite des ensembles de securite de reacteurs

    Energy Technology Data Exchange (ETDEWEB)

    Furet, J; Guyot, Ch [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-07-01

    A review is made of the circumstances which favor a good collection of maintenance data at the C.E.A. The large amount of data to be treated has made necessary the use of a computer for analyzing automatically the results collected. Here, only particular aspects of the reliability from the point of view of the electronics used for nuclear reactor control will be dealt with: sale and unsafe failures; probability of survival (in the case of reactor safety); availability. The general diagrams of the safety assemblies which have been drawn up for two types of reactor (power reactor and low power experimental reactor) are given. Results are presented of reliability analysis which could be applied to the use of functional modular elements, developed industrially in France. Improvement of this reliability appears to be fairly limited by an increase in the redundancy; on the other hand it is shown how it may be very markedly improved by the use of automatic tests with different frequencies for detecting unsafe failures rates of measurements for the sub-assemblies and for the logic sub-assemblies. Finally examples are given to show the incidence of the complexity and of the use of different technologies in reactor safety equipment on the reliability. (authors) [French] On rappelle les circonstances qui favorisent au C.E.A. la collecte d'une information valable des resultats de la maintenance. L'importance des donnees a traiter a rendu necessaire l'utilisation d'une calculatrice poux l'analyse automatique des resultats recueillis. On se limitera ici aux aspects particuliers de la fiabilite du point de vue de l'electronique pour le controle et la commande de reacteurs nucleaires: pannes sures et pannes non sures; probabilite de survie dans le cas de la securite des reacteurs; facteur de disponibilite. Les schemas de principe des ensembles de securite definis pour deux types de reacteurs (reacteur de puissance et reacteur experimental de faible puissance) sont indiques. On

  10. Special Equipment and/or Devices.

    Science.gov (United States)

    National Sanitation Foundation, Ann Arbor, MI.

    This standard covers the sanitation requirements for equipment and/or devices used in the storage, preparation, or handling of foods and beverages. The National Sanitation Foundation's basic criteria for the evaluation of special equipment and/or devices has been prepared to fulfill several specific needs, its major function being to serve as a…

  11. 21 CFR 1250.67 - Watering equipment.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Watering equipment. 1250.67 Section 1250.67 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... of drinking water or other beverages, or for food preservation purposes, equipment constructed so as...

  12. Using ADA Tasks to Simulate Operating Equipment

    Science.gov (United States)

    DeAcetis, Louis A.; Schmidt, Oron; Krishen, Kumar

    1990-01-01

    A method of simulating equipment using ADA tasks is discussed. Individual units of equipment are coded as concurrently running tasks that monitor and respond to input signals. This technique has been used in a simulation of the space-to-ground Communications and Tracking subsystem of Space Station Freedom.

  13. Enhancement of equipment services for Kozloduy NPP

    International Nuclear Information System (INIS)

    Schultz, Christophe

    2013-01-01

    Conclusion After 5 years of maintenance services, KNPP and AREVA have continuously intensified their partnership Close cooperation between KNPP, AREVA Local Office Engineers and OEM experts Involvement of sophisticated tools for diagnostics and condition monitoring Performance of engineering services and obsolescence evaluation Possibilities to perform equipment modernization of Electrical and IC equipment in future

  14. Emergency team personnel and technical equipment

    International Nuclear Information System (INIS)

    Muralt, R.

    1989-01-01

    The most important requirements for the emergency team can be summarized in three points. 1) The emergency team must be made up of top personnel from all fields and it should be functionally equiped. 2) The emergency teams must have complete command of their equipment. 3) The members of the team must be well motivated. 1 fig

  15. Weight/balance portable test equipment

    International Nuclear Information System (INIS)

    Whitlock, R.W.

    1994-01-01

    This document shows the general layout, and gives a part description for the weight/balance test equipment. This equipment will aid in the regulation of the leachate loading of tanker trucks. The report contains four drawings with part specifications. The leachate originates from lined trenches

  16. 7 CFR 550.38 - Equipment.

    Science.gov (United States)

    2010-01-01

    ... Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE GENERAL ADMINISTRATIVE POLICY FOR NON-ASSISTANCE COOPERATIVE AGREEMENTS Management of Agreements... Agency, the Cooperator shall use the equipment to be replaced as trade-in or sell the equipment and use...

  17. Quantitative techniques for medical equipment maintenance management

    NARCIS (Netherlands)

    Ben Houria, Zeineb; Masmoudi, Malek; Al Hanbali, Ahmad; Khatrouch, Ikram; Masmoudi, Faouzi

    2016-01-01

    The maintenance department in a hospital is responsible for ensuring the safety of medical equipment and their availability while keeping the operation costs minimal. The selection of the best maintenance strategy is a key decision to reduce the equipment downtime, increase the availability, and

  18. 21 CFR 606.60 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Equipment. 606.60 Section 606.60 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS CURRENT... following frequency, include but are not limited to: Equipment Performance check Frequency Frequency of...

  19. Plutonium Immobilization Can Loading Equipment Review

    International Nuclear Information System (INIS)

    Kriikku, E.; Ward, C.; Stokes, M.; Randall, B.; Steed, J.; Jones, R.; Hamilton, L.

    1998-05-01

    This report lists the operations required to complete the Can Loading steps on the Pu Immobilization Plant Flow Sheets and evaluates the equipment options to complete each operation. This report recommends the most appropriate equipment to support Plutonium Immobilization Can Loading operations

  20. Radio monitoring problems, methods, and equipment

    CERN Document Server

    Rembovsky, Anatoly; Kozmin, Vladimir; Smolskiy, Sergey

    2009-01-01

    Offers a unified approach to fundamental aspects of Automated Radio Monitoring (ARM). This book discusses the development, modeling, design, and manufacture of ARM systems. It provides classification and descriptions of modern high-efficient hardware-software ARM equipment, including the equipment for detection and radio direction-finding.

  1. Development of Equipment for Use in Sport

    Science.gov (United States)

    James, David

    2012-01-01

    No one has ever been able to create a running shoe that can make one run faster, but in other sports the design of equipment has the potential to offer considerable enhancement. Judgement has to be made as to whether such advantage becomes unfair. This article indicates many possible sports in which the equipment plays an important part in the…

  2. 36 CFR 1207.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... 1207.32 Parks, Forests, and Public Property NATIONAL ARCHIVES AND RECORDS ADMINISTRATION GENERAL RULES... as follows: (1) Items of equipment with a current per-unit fair market value of less than $5,000 may...) Items of equipment with a current per unit fair market value in excess of $5,000 may be retained or sold...

  3. 21 CFR 211.65 - Equipment construction.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Equipment construction. 211.65 Section 211.65 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS... construction. (a) Equipment shall be constructed so that surfaces that contact components, in-process materials...

  4. 47 CFR 18.203 - Equipment authorization.

    Science.gov (United States)

    2010-10-01

    ... information already on file with the Commission. (2) A technical report pursuant to §§ 18.207 and 18.311. (b... 47 Telecommunication 1 2010-10-01 2010-10-01 false Equipment authorization. 18.203 Section 18.203 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND MEDICAL EQUIPMENT...

  5. Thermal and hydrodynamic study of a whirling liquid hydrogen layer under high heat flux; Etude thermique et hydrodynamique d'une couche tourbillonnaire d'hydrogenen liquide sous flux de chaleur eleve

    Energy Technology Data Exchange (ETDEWEB)

    Ewald, R. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1968-03-01

    In order to achieve a cold neutrons source ({lambda} {>=} 4.10{sup -10} m) in a high flux reactor ({approx} 10{sup 15} neutrons/cm{sup 2}.s), a whirling liquid hydrogen layer (145 mm OD, effective thickness 15 mm, height about 180 mm) was formed, out-of-pile, in a cylindrical transparent glass vessel. The whirling motion was obtained by tangential injection of the liquid, near the wall. Thermal and hydrodynamical conditions of formation and laws of similarity of such a layer were studied. The characteristics of this whirling flow were observed as a function of mass flow rate (5 to 27 g/s; 4.3 to 23 l/mn), and of spillway width (18 and 25 mm). Six different nozzles were used : 1.0; 1.5; 1.9; 2.25; 2.65 and 3.0 mm ID. The total heat influx was found between 8.6 and 10.4 kW. The heat flux density was about 9.4 W/cm{sup 2} and the mean layer density around 80 per cent of that of the liquid hydrogen at 20.4 Kelvin. High speed movies were used to analyze the boiling regime. (author) [French] En vue de realiser une source de neutrons froids ({lambda} {>=} 4.10{sup -10} m) dans un reacteur a haut flux ({approx} 10{sup 15} neutrons thermiques/cm{sup 2}.s), on a forme dans un vase cylindrique transparent en verre, hors-pile, une couche tourbillonnaire ('vortex') d'hydrogene liquide (diametre exterieur 145 mm, epaisseur effective 15 mm, hauteur 180 mm environ). Le mouvement giratoire est obtenu par injection tangentielle du liquide pres de la paroi. L'etude porte sur la determination des conditions thermiques et hydrodynamiques de la formation d'une telle couche et sur les regles de similitude de ce phenomene. On a observe les caracteristiques de l'ecoulement giratoire en fonction du debit (de 5 a 27 g/s, soit de 4.3 a 23 1/mn), de la vitesse d'injection (entre 10 et 110 m/s) et de la largeur du deversoir (18 et 25 mm), ceci pour six diametres differents d'injecteur (1.0 ; 1.5; 1.9; 2.25; 2.65 et 3.0 mm). Le flux de chaleur total mesure

  6. Thermal Decomposition of Methane. Bibliographic Study and Proposal of a Mechanism Décomposition thermique du méthane. Étude bibliographique. Proposition de mécanisme

    Directory of Open Access Journals (Sweden)

    Billaud F.

    2006-11-01

    Full Text Available This review article gives the state-of-the-art of the upgrading of methane by the purely thermal route. It sums up the principal research since 1960 by giving, for each project, the operating conditions, type of reactor and the main results (order, inhibition of the reaction. It also comments on the reactions and the elementary processes written as well as the contribution of new kinetic constants. It emphasizes the effects of temperature, of dilution by inert gases, by hydrogen, by ethane and by water as well as the wall effects. After analyzing a great many publications dealing with the thermal decomposition of methane, this article attempts to give a mechanism and the major stages for which there seems to be a consensus among different authors and that account for the formation of hydrogen, ethane, ethylene, propene and acetylene. This mechanism can be broken down as follows :(a Primary formation of ethane and hydrogen. (b Secondary reactions of ethane. (c Secondary reactions of ethylene. (d Secondary reactions of acetylene. (e Secondary reactions of propene. This mechanism has also made possible the excellent simulation of the formation of all the above-mentioned products. However, concerning the formation of liquid hydrocarbons and coke, there is no coherent mechanism capable of simulating their formation. Cet article de revue fait le point sur la valorisation du méthane par voie purement thermique. Nous avons résumé les principaux travaux depuis 1960 en présentant pour chaque étude les différentes conditions opératoires, le type de réacteur, les principaux résultats (ordre, inhibition de la réaction. Nous avons également commenté les réactions et processus élémentaires écrits ainsi que l'apport de nouvelles constantes cinétiques. Nous soulignons également les effets de la température, de la dilution par des gaz inertes, par l'hydrogène, par l'éthane et par l'eau ainsi que les effets de parois. Après analyse du grand

  7. Thermal and hydrodynamic study of a whirling liquid hydrogen layer under high heat flux; Etude thermique et hydrodynamique d'une couche tourbillonnaire d'hydrogenen liquide sous flux de chaleur eleve

    Energy Technology Data Exchange (ETDEWEB)

    Ewald, R [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1968-03-01

    In order to achieve a cold neutrons source ({lambda} {>=} 4.10{sup -10} m) in a high flux reactor ({approx} 10{sup 15} neutrons/cm{sup 2}.s), a whirling liquid hydrogen layer (145 mm OD, effective thickness 15 mm, height about 180 mm) was formed, out-of-pile, in a cylindrical transparent glass vessel. The whirling motion was obtained by tangential injection of the liquid, near the wall. Thermal and hydrodynamical conditions of formation and laws of similarity of such a layer were studied. The characteristics of this whirling flow were observed as a function of mass flow rate (5 to 27 g/s; 4.3 to 23 l/mn), and of spillway width (18 and 25 mm). Six different nozzles were used : 1.0; 1.5; 1.9; 2.25; 2.65 and 3.0 mm ID. The total heat influx was found between 8.6 and 10.4 kW. The heat flux density was about 9.4 W/cm{sup 2} and the mean layer density around 80 per cent of that of the liquid hydrogen at 20.4 Kelvin. High speed movies were used to analyze the boiling regime. (author) [French] En vue de realiser une source de neutrons froids ({lambda} {>=} 4.10{sup -10} m) dans un reacteur a haut flux ({approx} 10{sup 15} neutrons thermiques/cm{sup 2}.s), on a forme dans un vase cylindrique transparent en verre, hors-pile, une couche tourbillonnaire ('vortex') d'hydrogene liquide (diametre exterieur 145 mm, epaisseur effective 15 mm, hauteur 180 mm environ). Le mouvement giratoire est obtenu par injection tangentielle du liquide pres de la paroi. L'etude porte sur la determination des conditions thermiques et hydrodynamiques de la formation d'une telle couche et sur les regles de similitude de ce phenomene. On a observe les caracteristiques de l'ecoulement giratoire en fonction du debit (de 5 a 27 g/s, soit de 4.3 a 23 1/mn), de la vitesse d'injection (entre 10 et 110 m/s) et de la largeur du deversoir (18 et 25 mm), ceci pour six diametres differents d'injecteur (1.0 ; 1.5; 1.9; 2.25; 2.65 et 3.0 mm). Le flux de chaleur total mesure est compris entre 8.6 et 10.4 kW et la

  8. Automatic monitoring of vibration welding equipment

    Science.gov (United States)

    Spicer, John Patrick; Chakraborty, Debejyo; Wincek, Michael Anthony; Wang, Hui; Abell, Jeffrey A; Bracey, Jennifer; Cai, Wayne W

    2014-10-14

    A vibration welding system includes vibration welding equipment having a welding horn and anvil, a host device, a check station, and a robot. The robot moves the horn and anvil via an arm to the check station. Sensors, e.g., temperature sensors, are positioned with respect to the welding equipment. Additional sensors are positioned with respect to the check station, including a pressure-sensitive array. The host device, which monitors a condition of the welding equipment, measures signals via the sensors positioned with respect to the welding equipment when the horn is actively forming a weld. The robot moves the horn and anvil to the check station, activates the check station sensors at the check station, and determines a condition of the welding equipment by processing the received signals. Acoustic, force, temperature, displacement, amplitude, and/or attitude/gyroscopic sensors may be used.

  9. Requirements for industrial x-ray equipment

    International Nuclear Information System (INIS)

    1987-01-01

    This safety code is concerned with the protection of all individuals who may be exposed to radiation emitted by X-ray equipment operating at energies up to 1 MeV as used in industrial radiography. This code presents basic radiation safety information for the protection of personnel operating and servicing X-ray equipment and other workers and the general public in the vicinity of areas where X-ray equipment is in operation. It specifies general safety features of design, construction and functioning of X-ray equipment and facilities; describes the responsibilities of the user, operator and maintenance personnel; contains recommendations to ensure that the X-ray equipment is used and maintained in accordance with the ALARA principle; and describes a program of personnel monitoring and radiation safety surveys. ( 6 refs., 5 tabs., 4 figs.)

  10. Equipment qualification research program: program plan

    International Nuclear Information System (INIS)

    Dong, R.G.; Smith, P.D.

    1982-01-01

    The Lawrence Livermore National Laboratory (LLNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC) has developed this program plan for research in equipment qualification (EQA). In this report the research program which will be executed in accordance with this plan will be referred to as the Equipment Qualification Research Program (EQRP). Covered are electrical and mechanical equipment under the conditions described in the OBJECTIVE section of this report. The EQRP has two phases; Phase I is primarily to produce early results and to develop information for Phase II. Phase I will last 18 months and consists of six projects. The first project is program management. The second project is responsible for in-depth evaluation and review of EQ issues and EQ processes. The third project is responsible for detailed planning to initiate Phase II. The remaining three projects address specific equipment; i.e., valves, electrical equipment, and a pump

  11. Development of Turbulence-Measuring Equipment

    Science.gov (United States)

    Kovasznay, Leslie S G

    1954-01-01

    Hot wire turbulence-measuring equipment has been developed to meet the more stringent requirements involved in the measurement of fluctuations in flow parameters at supersonic velocities. The higher mean speed necessitates the resolution of higher frequency components than at low speed, and the relatively low turbulence level present at supersonic speed makes necessary an improved noise level for the equipment. The equipment covers the frequency range from 2 to about 70,000 cycles per second. Constant-current operation is employed. Compensation for hot-wire lag is adjusted manually using square-wave testing to indicate proper setting. These and other features make the equipment adaptable to all-purpose turbulence work with improved utility and accuracy over that of older types of equipment. Sample measurements are given to demonstrate the performance.

  12. Oil and gas products and energy equipment

    International Nuclear Information System (INIS)

    1996-01-01

    The planned activities of the Canadian oil and gas products and energy equipment industry for 1996-1997, were presented. The sector is made up of approximately 1500 small and medium sized enterprises. The Canadian oil field manufacturing and servicing industry holds only a small 2.5% share of the world export market, but it is recognized internationally as one of the leading suppliers of advanced petroleum equipment. Their exports include specialized equipment for extracting oil sands, gathering and treatment facilities for sour gas, underbalanced drilling technologies, equipment for wells experiencing declining production rates, top motor drives, winter drilling rigs, and horizontal drilling technologies. They also offer petroleum industry software products. Most exploration and production equipment sold abroad by Canadian firms is manufactured in Canada, but there is an increasing trend toward manufacturing in the country of operation. 2 tabs

  13. Equipment for the handling of thorium materials

    International Nuclear Information System (INIS)

    Heisler, S.W. Jr.; Mihalovich, G.S.

    1988-01-01

    The Feed Materials Production Center (FMPC) is the United States Department of Energy's storage facility for thorium. FMPC thorium handling and overpacking projects ensure the continued safe handling and storage of the thorium inventory until final disposition of the materials is determined and implemented. The handling and overpacking of the thorium materials requires the design of a system that utilizes remote handling and overpacking equipment not currently utilized at the FMPC in the handling of uranium materials. The use of remote equipment significantly reduces radiation exposure to personnel during the handling and overpacking efforts. The design system combines existing technologies from the nuclear industry, the materials processing and handling industry and the mining industry. The designed system consists of a modified fork lift truck for the transport of thorium containers, automated equipment for material identification and inventory control, and remote handling and overpacking equipment for material identification and inventory control, and remote handling and overpacking equipment for repackaging of the thorium materials

  14. Câbles électriques - Calcul du courant admissible - Partie 2: Résistance thermique - Section 2: Méthode de calcul des coefficients de réduction de l'intensité de courant admissible pour des groupes de câbles posés à l'air libre et protégés du rayonnement solaire direct

    CERN Document Server

    1995-01-01

    Câbles électriques - Calcul du courant admissible - Partie 2: Résistance thermique - Section 2: Méthode de calcul des coefficients de réduction de l'intensité de courant admissible pour des groupes de câbles posés à l'air libre et protégés du rayonnement solaire direct

  15. Energy to the Edge (E2E) Equipment Assessment U.S. Army Rapid Equipping Force

    Science.gov (United States)

    2015-05-01

    84 Contents Energy to the Edge • U.S. Army Rapid Equipping Force U.S. Army Rapid Equipping Force 1.0 Executive Summary Executive Summary U.S. Army... audiovisual equipment. • Once radiant barrier liner is inserted, the process of subsequent setups • Cables for lighting and outlets are located...behind the internal barrier • The shelter comes with organic audiovisual equipment. b. • • This shelter has a different setup and tear down process

  16. Days individual equipment of protection and professional risks; Equipements de protection individuelle et risques professionnelles

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-07-01

    The personal protection equipment is studied in the legal way (legal liabilities, certification, European texts), technical way (ergonomics, painfulness of ventilated equipment wearing, reliability of a respirable air line, protection gloves against the chemical risk, exposure to nano particulates, working in hot area), human factors (hostile area and emotion management), studies on personal equipment such evaluation, efficiency, conception of new equipment, physiological tolerance, limit of use, and some general safety studies on the working places. (N.C.)

  17. Establishment of nuclear equipment qualification system

    International Nuclear Information System (INIS)

    Joo, Po Kook; Lim, Nam Jin; Lee, Young Gun

    2003-04-01

    This study is carried out by KEARI(Korea Atomic Energy Research Institute) as the lead organization in cooperation with KIMM(Korea Institute of Machinery and Materials), KTL(Korea Testing Laboratory) and KRISS(Korea Research Institute of Standards and Science) to construct a basis of efficient management of nuclear equipment qualification business by expanding test equipment of each of participating organization, and developing qualification technologies. As for KIMM, control system of large scale shaker was replaced with advanced system, and LOCA(Loss of Coolant Accident) test facility was installed. KTL is now capable of conducting seismic tests of nuclear I and C as a result of installation of seismic test equipment during the first two project years. KRISS participated in the Project with a view to have large scale EMI test equipment and related technologies. In parallel with expansion of test equipment, a industrial-educational-research cooperation committee, as an intermediate step toward integrated equipment qualification system to maximize the usage of test equipment, was established and cooperation methods were investigated. As a result, Korea Nuclear Equipment Qualification Association, an corporate juridical person, was established. Research on development of thermal and radiation aging test technology of nuclear materials was carried out by Hanyang University and SECO(Saehan Engineering and Qualification Co., Ltd.). Integrated Equipment Qualification Database was developed which contains material test data, equipment qualification data and other EQ related informations. Standard qualification procedures were developed in order for test laboratories and manufacturers to establish design requirements and to efficiently perform tests

  18. Equipment Reliability Program in NPP Krsko

    International Nuclear Information System (INIS)

    Skaler, F.; Djetelic, N.

    2006-01-01

    Operation that is safe, reliable, effective and acceptable to public is the common message in a mission statement of commercial nuclear power plants (NPPs). To fulfill these goals, nuclear industry, among other areas, has to focus on: 1 Human Performance (HU) and 2 Equipment Reliability (EQ). The performance objective of HU is as follows: The behaviors of all personnel result in safe and reliable station operation. While unwanted human behaviors in operations mostly result directly in the event, the behavior flaws either in the area of maintenance or engineering usually cause decreased equipment reliability. Unsatisfied Human performance leads even the best designed power plants into significant operating events, which can be found as well-known examples in nuclear industry. Equipment reliability is today recognized as the key to success. While the human performance at most NPPs has been improving since the start of WANO / INPO / IAEA evaluations, the open energy market has forced the nuclear plants to reduce production costs and operate more reliably and effectively. The balance between these two (opposite) goals has made equipment reliability even more important for safe, reliable and efficient production. Insisting on on-line operation by ignoring some principles of safety could nowadays in a well-developed safety culture and human performance environment exceed the cost of electricity losses. In last decade the leading USA nuclear companies put a lot of effort to improve equipment reliability primarily based on INPO Equipment Reliability Program AP-913 at their NPP stations. The Equipment Reliability Program is the key program not only for safe and reliable operation, but also for the Life Cycle Management and Aging Management on the way to the nuclear power plant life extension. The purpose of Equipment Reliability process is to identify, organize, integrate and coordinate equipment reliability activities (preventive and predictive maintenance, maintenance

  19. Experimental study of the thermal fission of uranium 235 in the region of symmetrical masses; Contribution a l'etude experimentale de la fission thermique de l'uranium 235 dans la region des masses symetriques

    Energy Technology Data Exchange (ETDEWEB)

    Ribrag, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-03-15

    Energy correlation experiments with fission fragments are strongly perturbed, in the symmetric region, by the detection of spurious events caused by the apparatus. We show that the measurement of an additional parameter, namely the difference in time-of-flight between the fragments, enables us to eliminate these difficulties. In this work we show also an original method of calibration of the time-of-flight set-up. For thermal fission of {sup 235}U, values of mass yields in the symmetric region are found to agree quantitatively with radiochemical values. Moreover, the average total kinetic energy distribution as a function of the pre-neutron emission masses of the fragments has been calculated. This curve presents in the symmetric region a large dip, the value of which takes on the value 21.2 {+-} 0.8 MeV. This value is smaller than previously published results. (author) [French] Les mesures correlees des energies cinetiques des fragments de fission sont fortement perturbees, dans la region symetrique, par la detection d'evenements aberrants d'origine instrumentale. Nous montrons que la mesure d'un parametre supplementaire, a savoir, la difference des temps de vol des deux fragments, nous permet d'eliminer ces difficultes. Dans ce travail, nous indiquons egalement une methode originale de calibration du dispositif de mesure des temps de vol. Dans le cas de la fission thermique de {sup 235}U, nous avons trouve, dans la region symetrique, une courbe de rendement des masses, en accord quantitatif avec les donnees radiochimiques. De plus, nous avons calcule la distribution de l'energie cinetique totale moyenne en fonction de la masse des fragments, avant emission neutronique. Cette courbe presente, dans la region symetrique, un creux important, dont la valeur atteint 21,2 {+-} 0,8 MeV. Cette valeur est inferieure aux resultats precedemment publies. (auteur)

  20. Tritium enrichment by thermal diffusion. I. Calculation of an installation for measuring natural tritium; Enrichissement du tritium par diffusion thermique. - I. Calcul d'une installation destinee a la mesure du tritium naturel

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, M.; Ravoire, J. [Commissariat a l' Energie Atomique, Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France)

    1966-07-01

    The natural content of tritium is so low that its measurement generally requires a preliminary enrichment. The thermal diffusion on hydrogen is studied as an enrichment method. The installation studied comprises two stages of columns of the hot-wire type, together with a device for transferring the tritium from the water sample into the hydrogen in the columns using catalytic exchange. A complete mathematical treatment for the operation of such a unit has been made and programmed for the IBM 7094 computer. An optimization has been effected by means of this program. It is shown that for similar performances, less hydrogen is retained in the case of hot-wire type columns than in the case of columns composed of concentric tubes. (authors) [French] La teneur naturelle du tritium est si faible que sa mesure demande generalement un enrichissement prealable. On etudie la diffusion thermique sur l'hydrogene comme moyen d'enrichissement. L'installation que l'on etudie comprend deux etages de colonnes du type fil chaud, et un dispositif de transfert du tritium de l'echantillon d'eau dans l'hydrogene des colonnes par echange catalytique. Un traitement mathematique complet du fonctionnement d'un tel ensemble a ete etabli et programme sur machine IBM 7094. Une optimisation a ete faite a l'aide du programme. On montre egalement qu'a performances egales, la retenue d'hydrogene est plus faible dans le cas des colonnes du type fil chaud que dans le cas des colonnes du type tubes concentriques. (auteurs)

  1. Contribution to the study of the thermal fission process for uranium 235 (1964); Contribution a l'etude du processus de la fission thermique de l'uranium 235 (1964)

    Energy Technology Data Exchange (ETDEWEB)

    Chahrtache, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-12-15

    This report deals with the study of the distribution of the masses of the fragments produced by the disintegration of the U-236 nucleus, formed when a U-235 nucleus captures a thermal neutron. The experimental method chosen consists in the simultaneous measurement using p-n silicon junction detectors of the energies of the two fragments emitted in coincidence. This measurement is first made by a conditioned analysis of the energy of one of the fragments and then by a two dimensional analysis of the energies of the two fragments. Systematic results, are obtained concerning the distribution of the masses for different values of the total kinetic energy. The five structures appearing both for the mass distributions and for the energies of the fragments are studied and discussed. Generally speaking, our results are in agreement with those obtained by the time-of-flight method. (author) [French] Le present rapport a pour objet t'etude de la distribution des masses des fragments emis lors de la fission du noyau U-236, forme par capture d'un neutron thermique par un noyau d'U-235. La methode experimentale choisie consiste en la mesure simultanee - a l'aide de detecteurs a jonction p-n au silicium des energies des deux fragments emis en coincidence. Cette mesure est d'abord effectuee par analyse conditionnee de l'energie de l'un des fragments puis par analyse bidimensionnelle des energies des deux fragments. Des resultats systematiques sont obtenus sur les distributions des masses pour differentes valeurs de l'energie cinetique totale. Les 'structures fines' apparaissant tant sur les distributions des masses que sur celles des energies des fragments sont egalement etudiees et discutees. D'une facon generale, nos resultats sont en accord avec ceux obtenus par la methode du temps de vol. (auteur)

  2. Tritium enrichment by thermal diffusion. I. Calculation of an installation for measuring natural tritium; Enrichissement du tritium par diffusion thermique. - I. Calcul d'une installation destinee a la mesure du tritium naturel

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, M; Ravoire, J [Commissariat a l' Energie Atomique, Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France)

    1966-07-01

    The natural content of tritium is so low that its measurement generally requires a preliminary enrichment. The thermal diffusion on hydrogen is studied as an enrichment method. The installation studied comprises two stages of columns of the hot-wire type, together with a device for transferring the tritium from the water sample into the hydrogen in the columns using catalytic exchange. A complete mathematical treatment for the operation of such a unit has been made and programmed for the IBM 7094 computer. An optimization has been effected by means of this program. It is shown that for similar performances, less hydrogen is retained in the case of hot-wire type columns than in the case of columns composed of concentric tubes. (authors) [French] La teneur naturelle du tritium est si faible que sa mesure demande generalement un enrichissement prealable. On etudie la diffusion thermique sur l'hydrogene comme moyen d'enrichissement. L'installation que l'on etudie comprend deux etages de colonnes du type fil chaud, et un dispositif de transfert du tritium de l'echantillon d'eau dans l'hydrogene des colonnes par echange catalytique. Un traitement mathematique complet du fonctionnement d'un tel ensemble a ete etabli et programme sur machine IBM 7094. Une optimisation a ete faite a l'aide du programme. On montre egalement qu'a performances egales, la retenue d'hydrogene est plus faible dans le cas des colonnes du type fil chaud que dans le cas des colonnes du type tubes concentriques. (auteurs)

  3. Measurement of a neutral particle flux by a thermal method using the junction temperature effect; Mesure d'un flux de particules neutres par une methode thermique mettant a contribution l'effet de temperature des jonctions

    Energy Technology Data Exchange (ETDEWEB)

    Caron, Anthime [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires. Services Scientifiques

    1966-07-01

    Among all the methods suitable for measuring neutral particle fluxes obtained by proton charge exchange in an organic gas, the thermal method has been chosen. The energy imparted by the neutral particles to the target in the form of heat leads to the latter temperature increasing; this temperature is usually followed with a thermocouple. In order to increase the sensitivity and the elegance of the apparatus the thermocouple has been replaced by a junction whose characteristics are known to vary with temperature. A calibration is carried out using a beam of charged particles. The response obtained is linear. Measurements have been made with a power of up to 1 mW; the accuracy increases with the energy provided; for 4 joules an accuracy of 10 per cent is obtained. The apparatus may be improved in particular by extending the measurement range towards low power values, and by increasing the accuracy. (author) [French] Parmi toutes les methodes utilisees pour la mesure d'un flux de particules neutres, obtenues par echange de charge de protons dans un gaz organique, nous avons choisi la methode thermique. L'energie cedee par les particules neutres a la cible sous forme de chaleur provoque une elevation de temperature de celle-ci; cette temperature est habituellement reperee par thermocouple. Pour accroitre la sensibilite et la finesse de l'appareillage, nous avons substitue au thermocouple une jonction dont on sait que les caracteristiques varient avec la temperature. Un etalonnage est realise par un faisceau de particules chargees. La reponse obtenue est lineaire. Des puissances de l'ordre du mW ont ete mesurees; la precision croit avec l'energie apportee; elle est de 10 pour cent quand celle-ci est de 4 joules. L'appareillage peut etre notablement perfectionne, pour reculer la gamme des mesures vers les basses puissances et accroitre la precision. (auteur)

  4. L'evolution thermique de la matière organique des sédiments : applications d'une simulation mathématique. Potentiel pétrolier des bassins sédimentaires de reconstitution de l'histoire thermique des sédiments Thermal Evolution of Organic Matter in Sediments : Application of a Mathematical Simulation. Petrleum Potential of Sedimentary Basins and Reconstructing the Thermal History of Sediments

    Directory of Open Access Journals (Sweden)

    Tissot B.

    2006-11-01

    Full Text Available Au moyen d'un modèle mathématique, on simule la dégradation thermique de la matière organique des sédiments. Les applications possibles de ce modèle concernent la recherche des zones favorables pour la prospection de l'huile ou du gaz, la détermination de l'époque de formation des hydrocarbures pour la comparer avec l'âge des pièges et celui des couvertures, l'évaluation des réserves ultimes d'un bassin, ainsi que la pyrogénation des schistes bitumineux. Le type de matière organique est représenté dans le modèle par un jeu de constantes qui sont déterminées par des essais de laboratoire; on discute en particulier la distribution des énergies d'activation et sa signification en rapport avec la composition du kérogène. Les autres données nécessaires sont la reconstitution géologique de l'enfouissement et le gradient géothermique. La reconstitution de la géothermie ancienne pose un problème particulier. En associant la mesure de la réflectance de la vitrinite et la loi d'enfouissement, on peut, au moyen d'un modèle d'évolution de la vitrinite, rétablir dans la plupart des cas l'histoire thermique de la matière organique. Ce résultat présente certes un grand intérêt pour l'exploration pétrolière, mais son champ d'application dépasse largement ce domaine et s'étend aux problèmes de géologie générale géothermie, diagenèse des sédiments, tectonique globale, etc. A mathematical model is used to simulate the thermal degradation of the organic matter in sediments. The possible applications of this model have to do with the seorch for favorable ail or gas prospection zones, determining the period when hydrocarbons were formed so as to compare it with the age of traps and caprocks, and estimating the ultimate reserves of a basin a well as the pyrogenation of ail shales. The type of organic matter is represented in the model by a set of constants that are determined by laboratory tests. This article in

  5. Modélisation d'une détente quasi-isotherme d'un gaz par contact direct avec un fluide caloporteur

    OpenAIRE

    Blaise , Mathilde; Maillet , Denis; Feidt , Michel; Alemany , Antoine; Forcinetti , Renato

    2015-01-01

    National audience; Les besoins en électricité sont croissants, cependant, les rejets thermiques industriels sont peu valorisés. La reconsidération des moteurs à apport de chaleur externe est un enjeu d'actualité pour la valorisation des rejets thermiques. Dans ces derniers, la phase de détente motrice offre des possibilités d'amélioration. L'idée ici est d'accompagner cette étape par un apport de chaleur par contact direct avec un fluide caloporteur. En effet, la détente d'un gaz entre une ha...

  6. Drawing Evaluation Report for Sampling Equipment Drawings

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    This document presents the results of a task to update the evaluation of River Protection Project (WP) sampling equipment drawings and updates the assigned drawings category as either essential, support, or general drawings. This report updates the drawing evaluation that was originally done per Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation. The scope of this report is limited to updating the evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the RPP Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, all core sampling equipment, and Light Duty Utility Arm (LDUA) (see LMHC contract No. 519, release 10). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The Cone Penetrometer system, which is depicted on vendor drawings, (not H- series), is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and was not included in the original scope for this update and will be addressed in the evaluation update scheduled for later in fiscal year 1999, when equipment ownership is determined

  7. Drawing evaluation report for sampling equipment drawings

    International Nuclear Information System (INIS)

    WILSON, G.W.

    1999-01-01

    This document presents the results of a task to evaluate Tank Waste Remediation System (TWRS) sampling equipment drawings and identifies drawings category as either essential, support, or general drawings. This report completes the drawing evaluation task as outlined in Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation (Wilson, 1997). The scope of this report is limited to an evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the TRWS Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, and all core sampling equipment (see LMHC Task Order 304). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Light Duty Utility Arm (LDUA), Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The LDUA drawings are addressed in the Characterization Equipment Essential Drawings (HNF 1998). The Cone Penetrometer system drawings which are vendor drawings (not H- series) is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and were not included in the original scope for this evaluation and will be addressed in the evaluation update scheduled for fiscal year 1999

  8. Progress on EPRI electrical equipment qualification research

    International Nuclear Information System (INIS)

    Sliter, G.E.

    1983-01-01

    The objective of EPRI's electrical equipment qualification research program is to provide technical assistance to utilities in meeting nuclear plant safety requirements in a manner consistent with the state of the art. This paper reports progress on several research projects including: radiation effects studies, which compile data on degradation of organic materials in electrical equipment exposed to operational and accident radiation doses; the Equipment Qualification Data Bank, which is a remotely accessible computer system for disseminating qualification information on in-plant equipment, seismic data, and materials data; an aging/seismic correlation program, which is providing test data showing that, in many cases, age degradation has a negligibly small effect on the performance of electrical components under seismic excitation; a review of condition monitoring techniques, which has identified surveillance methods for measuring key performance parameters that have the potential for predicting remaining equipment life; and large-scale hydrogen burn equipment response tests, which are providing data to assess the ability of equipment to remain functional during and after hydrogen burning in postulated degraded core accidents

  9. Long Length Contaminated Equipment Maintenance Plan

    International Nuclear Information System (INIS)

    ESVELT, C.A.

    2000-01-01

    The purpose of this document is to provide the maintenance requirements of the Long Length Contaminated Equipment (LLCE) trailers and provide a basis for the maintenance frequencies selected. This document is applicable to the LLCE Receiver trailer and Transport trailer assembled by Mobilized Systems Inc. (MSI). Equipment used in conjunction with, or in support of, these trailers is not included. This document does not provide the maintenance requirements for checkout and startup of the equipment following the extended lay-up status which began in the mid 1990s. These requirements will be specified in other documentation

  10. Remote handling equipment for CANDU retubing

    International Nuclear Information System (INIS)

    Crawford, G.S.; Lowe, H.

    1993-01-01

    Numet Engineering Ltd. has designed and supplied remote handling equipment for Ontario Hydro's retubing operation of its CANDU reactors at the Bruce Nuclear Generating Station. This equipment consists of ''Retubing Tool Carriers'' an'' Worktables'' which operate remotely or manually at the reactor face. Together they function to transport tooling to and from the reactor face, to position and support tooling during retubing operations, and to deliver and retrieve fuel channels and channel components. This paper presents the fundamentals of the process and discusses the equipment supplied in terms of its design, manufacturing, components and controls, to meet the functional and quality requirements of Ontario Hydro's retubing process. (author)

  11. Equipment for x- and gamma ray radiography

    International Nuclear Information System (INIS)

    Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

    2004-01-01

    The following topics related to the equipment for x - and gamma ray radiography are discussed in this chapter. The topics are x-ray source for Industrial Radiography: properties of x-ray, generation of x-ray, mechanism of x-ray production, x-ray equipment, power supply, distribution of x-ray intensity along the tube: gamma ray source for Industrial Radiography: properties of gamma rays, gamma ray sources, gamma ray projectors on cameras, source changing. Care of Radiographic Equipments: Merits and Demerits of x and Gamma Rays

  12. Exposure parameters in fluoroscopy equipment. Quality control

    International Nuclear Information System (INIS)

    Alonso, M.; Castaneda, M.J.; Matorras, P.; Diaz-Caneja, N.; Gutierrez, I.

    1992-01-01

    Within the quality control program in Diagnostic Radiology currently being undertaken at the 'Marques de Valdecilla' University Hospital, the corresponding specification and procedure prototypes for the control of conventional radioscopy equipment have been elaborated and applied. This paper presents the values proposed in the specifications and those obtained for the following radioscopy equipment parameters: reference kerma, and its reproducibility, kerma linearity, maximum kerma at the skin, and total filtration. The results obtained indicate that the equipment studied could comply with specified requirements if a Maintenance Program were to be implemented in coordination with the Quality Control Program. (author)

  13. LMZ experience in refurbishment of hydroturbine equipment

    Energy Technology Data Exchange (ETDEWEB)

    Sotnikov, Anatoly A. [LMZ, St. Petersburg (Russian Federation). Div. of Hydraulic Machine

    2000-07-01

    AO LMZ experience in refurbishment of hydroturbine equipment is generalized. Hydraulic turbines of many power stations having been in service of more than 30 years need rehabilitation and modernization. As a rule, the following problems are solved in the process of refurbishment works: increase of turbine efficiency and output, ensuring of reliable operation of the equipment during the next length of life, ensuring the environmental safety of the equipment, furnishing of the power station with up to date automatic control systems. The process of refurbishment used by LMZ is described. The examples of refurbishment are given. (author)

  14. Incidents of chemical reactions in cell equipment

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, N.M.; Barlow, C.R. [Uranium Enrichment Organization, Oak Ridge, TN (United States)

    1991-12-31

    Strongly exothermic reactions can occur between equipment structural components and process gases under certain accident conditions in the diffusion enrichment cascades. This paper describes the conditions required for initiation of these reactions, and describes the range of such reactions experienced over nearly 50 years of equipment operation in the US uranium enrichment program. Factors are cited which can promote or limit the destructive extent of these reactions, and process operations are described which are designed to control the reactions to minimize equipment damage, downtime, and the possibility of material releases.

  15. [Development of Hospital Equipment Maintenance Information System].

    Science.gov (United States)

    Zhou, Zhixin

    2015-11-01

    Hospital equipment maintenance information system plays an important role in improving medical treatment quality and efficiency. By requirement analysis of hospital equipment maintenance, the system function diagram is drawed. According to analysis of input and output data, tables and reports in connection with equipment maintenance process, relationships between entity and attribute is found out, and E-R diagram is drawed and relational database table is established. Software development should meet actual process requirement of maintenance and have a friendly user interface and flexible operation. The software can analyze failure cause by statistical analysis.

  16. Automatic dose-rate controlling equipment

    International Nuclear Information System (INIS)

    Szasz, T.; Nagy Czirok, Cs.; Batki, L.; Antal, S.

    1977-01-01

    The patent of a dose-rate controlling equipment that can be attached to X-ray image-amplifiers is presented. In the new equipment the current of the photocatode of the image-amplifier is led into the regulating unit, which controls the X-ray generator automatically. The advantages of the equipment are the following: it can be simply attached to any type of X-ray image-amplifier, it accomplishes fast and sensitive regulation, it makes possible the control of both the mA and the kV values, it is attached to the most reliable point of the image-transmission chain. (L.E.)

  17. Thermal design of horizontal tube boilers. Numerical and experimental investigation; Modelisation thermique de bouilleurs a tubes horizontaux. Etude numerique et validation experimentale

    Energy Technology Data Exchange (ETDEWEB)

    Roser, R.

    1999-11-26

    This work concerns the thermal design of kettle reboilers. Current methods are highly inaccurate, regarded to the correlations for external heat transfer coefficient at one tube scale, as well as to two-phase flow modelling at boiler scale. The aim of this work is to improve these thermal design methods. It contains an experimental investigation with typical operating conditions of such equipment: an hydrocarbon (n-pentane) with low mass flux. This investigation has lead to characterize the local flow pattern through void fraction measurements and, from this, to develop correlations for void fraction, pressure drop and heat transfer coefficient. The approach is original, since the developed correlations are based on the liquid velocity at minimum cross section area between tubes, as variable characterizing the hydrodynamic effects on pressure drop and heat transfer coefficient. These correlations are shown to give much better results than those suggested up to now in the literature, which are empirical transpositions from methods developed for inside tube flows. Furthermore, the numerical code MC3D has been applied using the correlations developed in this work, leading to a modeling of the two-phase flow in the boiler, which is a significant progress compared to current simplified methods. (author)

  18. Bois-Noirs ore. Recovery of uranium of solutions from acid treatment. Results of industrial tests at the Gueugnon plant; Minerai des Bois-Noirs. Recuperation de l'uranium des solutions d'attaques acides. Resultats des essais industriels effectues a l'usine de Gueugnon

    Energy Technology Data Exchange (ETDEWEB)

    Le Bris, J

    1959-04-01

    Industrial-scale tests are reported of the efficiency of two recovery processes for the separation of uranium from sulfuric acid pickling solutions used on ore from Bois-Noirs, at the Gueugnon works. The final stage of each process is sodium uranate. The earlier part of the report deals with tests of the separation of uranium from foreign metals by fractional precipitation. The second part deals with the separation of uranium from these metals by carbonation of the solutions. (author) [French] Le present rapport concerne les essais industriels de deux procedes de recuperation de l'uranium de solutions d'attaque sulfurique du minerai des Bois-Noirs a l'usine de Gueugnon. Le stade final pour ces deux procedes etant l'uranate de sodium, une premiere partie est consacree aux essais de separation de l'uranium des metaux etrangers par precipitation fractionnee; une deuxieme partie est consacree aux essais de separation de l'uranium des metaux etrangers par carbonatation des solutions d'attaque du minerai. (auteur)

  19. Maintenance and fabrication of nuclear electronic equipment

    International Nuclear Information System (INIS)

    Hong, Seok Boong; Chung, Chong Eun; Hwang, In Koo; Koo, In Soo; Park, Bum; Kim, Soo Hee; Lee, Seong Joo; Kim, Min Seok; Choi, Wha Lim

    2011-12-01

    - process equipment at PIEF, Chemical Analysis Team and RWFTF have been calibrated. - The electronic equipment and radiation equipment at RWTF and PIEF have been prepared. - Development and installation of integrated RMS software for Hanaro Cold Neutron Laboratory Building(CNLB) RMS, and development and performance upgrade of a portal monitor for CNLB. - Performance test of the Hardware/Software of digital unit controller has been performed, and functional upgrade of the Hardware/Software of stimulator for SMART MMIS performance test facility has also been performed. - A controller of high voltage power supply for a small electron beam generator and a controller for razer pinning and a remote monitoring apparatus of cathode power supply for a 0.2 Mev. small electron beam generator have been designed and fabricated. - Database construction for effective maintenance for the process equipment and radiation instruments are designed and constructed

  20. 18 CFR 367.57 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... piers and foundations that are designed to be as permanent as the buildings that house the equipment, or... walls, ceilings or floors or without in some way impairing the building, must be included in the...

  1. Capitalization of Defense Technology Security Administration Equipment

    National Research Council Canada - National Science Library

    Gimble, Thomas

    1996-01-01

    ... $5.2 million in the Equipment in Use account on its trial balance. Starting with FY 1996, Defense Technology Security Administration financial data will be included in consolidated DoD financial statements...

  2. Hot conditioning equipment conceptual design report

    Energy Technology Data Exchange (ETDEWEB)

    Bradshaw, F.W., Westinghouse Hanford

    1996-08-06

    This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage.

  3. Hot conditioning equipment conceptual design report

    International Nuclear Information System (INIS)

    Bradshaw, F.W.

    1996-01-01

    This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage

  4. ENERGY STAR Certified Electric Vehicle Supply Equipment

    Data.gov (United States)

    U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 1.0 ENERGY STAR Program Requirements for Electric Vehicle Supply Equipment that are...

  5. Study Of Robotic Replacement Of Equipment Modules

    Science.gov (United States)

    Backes, Paul G.; Tso, Kam S.

    1992-01-01

    Report discusses issues pertaining to control of single-arm robotic manipulator to remove and install interchangeable equipment modules. Presents preliminary control strategy intended to guide development of control algorithms, along with analyses of problems arising in implementing strategy.

  6. Market survey of level measurement equipment

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    In a market survey of level measurement equipment from 42 manufacturers, which is based on different principles of measurement and which is used for different applications, the data of the various manufacturers is compiled. (orig./HP) [de

  7. 77 FR 13173 - Best Equipped Best Served

    Science.gov (United States)

    2012-03-05

    ... on the best equipped, best performing, best served concept for implementation in the 2012-2014... Advisory Committee (NAC). FAA is seeking stakeholder input on the technical and operational feasibility of...

  8. Methods and equipments used in power reactors

    International Nuclear Information System (INIS)

    Beraha, R.; Delevallee, A.

    1976-01-01

    The various reactor γ fuel scanning facilities presently operating around the world are reviewed. Both equipments proposed by FRAMATOME are described: one is intended for scanning removable fuel pencils, and the other one for fuel assembly scanning [fr

  9. AX Tank Farm ancillary equipment study

    International Nuclear Information System (INIS)

    SKELLY, W.A.

    1999-01-01

    This report examines the feasibility of remediating ancillary equipment associated with the 241-AX Tank Farm at the Hanford Site. Ancillary equipment includes surface structures and equipment, process waste piping, ventilation components, wells, and pits, boxes, sumps, and tanks used to make waste transfers to/from the AX tanks and adjoining tank farms. Two remedial alternatives are considered: (1) excavation and removal of all ancillary equipment items, and (2) in-situ stabilization by grout filling, the 241-AX Tank Farm is being employed as a strawman in engineering studies evaluating clean and landfill closure options for Hanford single-shell tanks. This is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms

  10. VIRTUAL ELECTRONIC COMPONENTS OF THE ELECTRONIC EQUIPMENT

    Directory of Open Access Journals (Sweden)

    E. Lazarevich

    2013-01-01

    Full Text Available The article is present new idea of the creation, developments and improvements of the electronic equipment of complex systems by means of the virtual electronic components. The idea of the virtual electronic components is a presentation and perception of the creation and developments of the equipment on two forming: real – in the manner of standard marketed block of the intellectual property and image – in the manner of virtual component. The real component in most cases slows the development of the electronic equipment. The imaginary component is the «locomotive» of development of the electronic equipment. The Imaginary component contains the scientific has brushed against developer. The scientific has brushed against developer reveals of itself in the manner of virtual component on the modern level of the design rates of microelectronics.

  11. 7 CFR 58.626 - Packaging equipment.

    Science.gov (United States)

    2010-01-01

    ... containers with frozen desserts shall be constructed so that all product contact surfaces shall be of... Standards for Equipment for Packaging Frozen Desserts and Cottage Cheese. Quality Specifications for Raw...

  12. ENERGY STAR Certified Small Network Equipment

    Data.gov (United States)

    U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 1.0 ENERGY STAR Program Requirements for Small Networking Equipment that are effective as...

  13. Ethical home medical equipment business practices.

    Science.gov (United States)

    Parver, C

    1991-11-01

    National uniform standards as a condition for receipt of a Medicare provider number would help rid the home medical equipment industry of those unethical and unscrupulous suppliers who have tarnished the industry's reputation.

  14. Experience with rotating equipment in FBTR

    International Nuclear Information System (INIS)

    Babu, A.; Subramanian, K.G.; Selvam, B.

    2006-01-01

    Fast breeder test reactor (FBTR) is a 40MWth sodium cooled PuC-UC fuelled fast breeder reactor located at Kalpakkam, Tamilnadu. FBTR has a variety of mechanical and electrical equipment comprising of single stage and multi stage water pumps, sodium pumps, compressors, Chiller units, Diesel Generator sets, vacuum pumps, ventilation fans, Turbo generator etc. The degree and extent of maintenance on these equipment are decided based on nuclear safety, station technical specification requirements, design criteria and operating philosophy. The variety and complexity of the equipment in FBTR demands various maintenance strategies (preventive, predictive, proactive etc.) for their upkeep. This paper discusses the performance of all mechanical and electrical equipment in FBTR, measures taken for their upkeep, major modifications done to prevent recurring failures, condition monitoring programme implemented, Maintenance Management and Information System developed for data acquisition and dissemination, etc. (author)

  15. Radiation therapy sources, equipment and installations

    International Nuclear Information System (INIS)

    2011-03-01

    The safety code for Telegamma Therapy Equipment and Installations, (AERB/SC/MED-1) and safety code for Brachytherapy Sources, Equipment and Installations, (AERB/SC/MED-3) were issued by AERB in 1986 and 1988 respectively. These codes specified mandatory requirements for radiation therapy facilities, covering the entire spectrum of operations ranging from the setting up of a facility to its ultimate decommissioning, including procedures to be followed during emergency situations. The codes also stipulated requirements of personnel and their responsibilities. With the advent of new techniques and equipment such as 3D-conformal radiation therapy, intensity modulated radiation therapy, image guided radiation therapy, treatment planning system, stereotactic radiosurgery, stereotactic radiotherapy, portal imaging, integrated brachytherapy and endovascular brachytherapy during the last two decades, AERB desires that these codes be revised and merged into a single code titled Radiation Therapy Sources, Equipment, and Installations

  16. Equipment for oral surgery in small animals.

    Science.gov (United States)

    Reiter, Alexander M

    2013-05-01

    This article provides an overview of equipment used for oral surgery. Specific instruments and materials used when performing relevant operative procedures are also mentioned in other articles in this issue. Copyright © 2013 Elsevier Inc. All rights reserved.

  17. A Phenomenological Heat Transfer Model of SI Engines – Application to the Simulation of a Full-Hybrid Vehicle Un modèle phénoménologique de transfert thermique au sein de moteurs à allumage commandé — Application à la simulation d’un véhicule full-hybride

    Directory of Open Access Journals (Sweden)

    Dubouil R.

    2013-02-01

    ICE on its thermal behaviour. Especially, it appears that the efficiency of the engine is less penalized than expected by the cold state of the engine. Finally, a parametric study of the modeled engine and a research of a possible optimization of the engine efficiency and the warm-up period are done. Un véhicule hybride électrique permet des économies de carburant non négligeables grâce à une meilleure utilisation du Moteur à Combustion Interne (MCI sur des points de régime-charge à meilleurs rendements. Cependant ce fonctionnement particulier a un impact sur le comportement thermique du MCI, en particulier, pendant sa période de chauffe après un départ à froid. En effet, le moteur peut être arrêté lorsque le véhicule est à l’arrêt (système Stop&Start ainsi que pendant les phases de propulsion en électrique pur (possible à vitesse faible si l’état de charge de la batterie est suffisamment élevé entraînant un manque de source de chaleur et donc un ralentissement du réchauffement du moteur. De plus, l’utilisation du MCI avec des charges plus importantes lors de la recharge des batteries provoque une augmentation de la puissance thermique disponible issue de la combustion. Les stratégies de contrôle d’un véhicule hybride (répartition d’énergie entre les deux types de propulsion : thermique et électrique ont un effet important sur sa consommation finale. Ainsi, la simulation phénoménologique 0D de véhicules hybrides est utile afin d’évaluer l’efficacité de ces stratégies. Cependant, il existe un nombre très limité d’études où la période de chauffe du moteur thermique est prise en compte dans ce type de simulations. Un outil de simulation utilisant le logiciel Amesim a été développé afin de simuler la montée en température du MCI utilisé dans un système de propulsion hybride parallèle. Le modèle est construit afin de prendre en compte les phénomènes thermiques ayant lieu au sein de cet élément. Un

  18. Manufacture and maintenance of laboratory equipment

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Chang Kyu; Hwang, Bong Ha; Lee, Jong Wha; Kim, Jong Kyun; Yeum, Ki Eon; Park, Myung Ku; Hong, Soon Eon; Choi, Ho Young; An, Dae Kyu; An, Choon; Park, In Won; Kim, Kyung Sik; Lee, Won Jae; Yoon, Ki Byung; Kim, Heung Woo; Lee, In Bae; Yeom, Jeong Hyun; Lee, Chul Ku; Sin, Keon Ju; Oh, Wan Ho; Seo, Yong Chil; Yang, Song Yeul; Lee, Young Soon; Choi, Byung Kwon; Chang, Kyung Duk [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1993-12-01

    This report on the manufacture and maintenance of laboratory equipment contains working contents, scope and contents of request working to the machine shop, also records the principal production design, manufacture contents and a relevant working drawing. The working content and scope of the machine shop is to support the successful and convenient performance of the R and D by manufacture and maintenance of all sorts of laboratory equipment. 11 tabs., 3 figs. (Author) .new.

  19. Manufacture and maintenance of laboratory equipment

    International Nuclear Information System (INIS)

    Hwang, Chang Kyu; Hwang, Bong Ha; Lee, Jong Wha; Kim, Jong Kyun; Yeum, Ki Eon; Park, Myung Ku; Hong, Soon Eon; Choi, Ho Young; An, Dae Kyu; An, Choon; Park, In Won; Kim, Kyung Sik; Lee, Won Jae; Yoon, Ki Byung; Kim, Heung Woo; Lee, In Bae; Yeom, Jeong Hyun; Lee, Chul Ku; Sin, Keon Ju; Oh, Wan Ho; Seo, Yong Chil; Yang, Song Yeul; Lee, Young Soon; Choi, Byung Kwon; Chang, Kyung Duk

    1993-12-01

    This report on the manufacture and maintenance of laboratory equipment contains working contents, scope and contents of request working to the machine shop, also records the principal production design, manufacture contents and a relevant working drawing. The working content and scope of the machine shop is to support the successful and convenient performance of the R and D by manufacture and maintenance of all sorts of laboratory equipment. 11 tabs., 3 figs. (Author) .new

  20. Ion beam stabilization in ion implantation equipment

    International Nuclear Information System (INIS)

    Pina, L.

    1973-01-01

    The results are presented of experimental efforts aimed at ion beam current stabilization in an equipment for ion implantation in solids. The related problems of power supplies are discussed. Measured characteristics of laboratory equipment served the determination of the parameters to be required of the supplies as well as the design and the construction of the supplies. The respective wiring diagram is presented. (J.K.)

  1. Manufacture and maintenance of laboratory equipment

    International Nuclear Information System (INIS)

    Kim, Jong Kyun; Hwang, Chang Kyu; Hwang, Bong Ha; Lee, Jong Wha; Yeom, Ki Eon; Park, Myung Ku; Hong, Soon Hyeon; Choi, Ho Young; An, Dae Kyu; An, Choon; Park, In Won; Kim, Kyeong Sik; Lee, In Bae; Yeom, Jeong Heon; Lee, Chul Ku; Sin, Keon Ju; Oh, Wan Ho; Choi, Byung Kwon; Chang, Kyeong Duk; Lee, Young Soon

    1995-12-01

    This report on the manufacture and maintenance of laboratory equipment contains working contents, scope and contents of a request working to the Machine Shop, also records the principal production design, manufacture contents and a relevant working drawing. The working content and scope of the Machine Shop is to support the successful and convenient performance of the Research and development by manufacture and maintenance of all sorts of laboratory equipment. 12 tabs., 5 figs. (Author) .new

  2. Regulatory process for material handling equipment

    International Nuclear Information System (INIS)

    Rajendran, S.; Agarwal, Kailash

    2017-01-01

    Atomic Energy (Factories) Rules (AEFR) 1996, Rule 35 states, 'Thorough inspection and load testing of a Crane shall be done by a Competent Person at least once every 12 months'. To adhere to this rule, BARC Safety Council constituted 'Material Handling Equipment Committee (MHEC)' under the aegis of Conventional Fire and Safety Review Committee (CFSRC) to carry out periodical inspection and certification of Material Handling Equipment (MHE), tools and tackles used in BARC Facilities at Trombay, Tarapur and Kalpakkam

  3. Manufacture and maintenance of laboratory equipment

    International Nuclear Information System (INIS)

    Kim, J. K.; Whang, C. K.; Lee, J. H.; Youm, K. Y.; Hong, S. H.; Choi, H. Y.; An, C.; Park, I. W.; Kim, K. S.; Lee, W. J.; Yoon, K. B.; Kim, H. W.; Lee, I. B.; Lee, C. K.; Youm, J. H.; Oho, W. H.; Choi, B. K.; Jang, K. D.

    1996-12-01

    This report on the manufacture and maintenance of laboratory equipment contains working contents, scope and contents of a request working to the Machine Shop, also records the principal production design, manufacture contents and a relevant working drawing. The working content and scope of the Machine Shop is to support the successful and convenient performance of the R and D by manufacture and maintenance of all sorts of laboratory equipment. (author). 9 tabs., 12 figs

  4. Stud bolt handling equipment for reactor vessel

    International Nuclear Information System (INIS)

    Bunyan, T.W.

    1989-01-01

    Reactor vessel stud bolt handling equipment includes means for transferring a stud bolt to a carrier from a parking station, or vice versa. Preferably a number of stud bolts are handled simultaneously. The transfer means may include cross arms rotatable about extendable columns, and the equipment is mounted on a mobile base for movement into and out of position. Each carrier comprises a tubular socket and an expandable sleeve to grip a stud bolt. (author)

  5. Protecting electrical equipment against dust explosions

    Energy Technology Data Exchange (ETDEWEB)

    Kaiser, J

    1981-07-01

    The new ordinance on electrical equipment in hazardous areas and the new VDE 0165/6.80 have brought about significant changes in the field of electrical equipment in areas with a explosion hazard due inflammable dust. There are no constructional regulations yet in this field, and producers, planners, and users are uncertain about what measures to take. The article attempts to clear up a few points.

  6. Manufacture and maintenance of laboratory equipment

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Kyun; Hwang, Chang Kyu; Hwang, Bong Ha; Lee, Jong Wha; Yeom, Ki Eon; Park, Myung Ku; Hong, Soon Hyeon; Choi, Ho Young; An, Dae Kyu; An, Choon; Park, In Won; Kim, Kyeong Sik; Lee, In Bae; Yeom, Jeong Heon; Lee, Chul Ku; Sin, Keon Ju; Oh, Wan Ho; Choi, Byung Kwon; Chang, Kyeong Duk; Lee, Young Soon [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1995-12-01

    This report on the manufacture and maintenance of laboratory equipment contains working contents, scope and contents of a request working to the Machine Shop, also records the principal production design, manufacture contents and a relevant working drawing. The working content and scope of the Machine Shop is to support the successful and convenient performance of the Research and development by manufacture and maintenance of all sorts of laboratory equipment. 12 tabs., 5 figs. (Author) .new.

  7. Profit ability versus construction equipment maintenance

    OpenAIRE

    Clutts, Craig A.

    2010-01-01

    CIVINS (Civilian Institutions) Thesis document Approved for public release ; distribution is unlimited Construction equipment is a high cost of capital investment necessary for the successful existence of a private construction company and essential to the mission success of the Naval Construction Force (NCF). The highest impact cost factor other than the initial purchase investment is the expenses related to maintenance and repair. As the equipment ages, the ownership costs decrease an...

  8. Electronic equipment for spectrometric data processing

    International Nuclear Information System (INIS)

    Antonov, L.J.; Trenev, A.M.; Todorova, E.I.; Dimitrov, V.D.

    1978-01-01

    Electronic equipment carrying out logical operations and a full set of the arithmetic operations was developed for spectrometric data processing. The flowsheet of the computing part of the device, made on the basis of a specialized integral circuit, is given. The device includes input registers, multiplexor, matrix commutator, arithmetic unit and indication unit. The equipment is rated to carry out calculations according to comparatively complex formulae in several seconds

  9. Physical protection equipment study. Final report

    International Nuclear Information System (INIS)

    Haberman, W.

    1977-06-01

    This report summarizes the work performed by MITRE for the U.S. Nuclear Regulatory Commission. The major products of this effort are a Catalog of Physical Protection Equipment, a Guide for Evaluation of Physical Protection Equipment, a book of Reference Materials, and a set of guidelines for use in the development of a methodology for measuring levels of security system effectiveness. A summary of recommendations resulting from this study is also presented

  10. Industrial Employment, Investment Equipment and Economic Growth

    OpenAIRE

    Dellas, Harris

    2000-01-01

    The industrialization of labour is the main engine of growth during the early stages of economic development. In less developed countries, equipment investment has played a less important role than non-equipment investment; and it has only proved growth enhancing when it either encountered a substantial industrial labour force or fostered a large increase in the share of industrial employment. These findings draw attention to the effects of investment on the composition of the labour force; a...

  11. The french safety approach regarding equipment qualification

    International Nuclear Information System (INIS)

    Jalouneix, J.; Deletre, G.; Henry, J.Y.; Rousseau, L.

    1989-10-01

    The qualification of the equipment, used in France on nuclear reactors and reactor components, is discussed. The approach on safety involves the qualification of mechanical and electrical components, under operating and under seismic conditions. The principles of the qualification program and the list of the equipment concerned, are given. The conditions in which qualification tests are performed and the methods applied, are summarized. The actions for preserving the qualification procedures, are considered

  12. Equipment system for advanced nuclear fuel development

    International Nuclear Information System (INIS)

    Kwon, Hyuk Il; Ji, C. G.; Bae, S. O.

    2002-11-01

    The purpose of the settlement of equipment system for nuclear Fuel Technology Development Facility(FTDF) is to build a seismic designed facility that can accommodate handling of nuclear materials including <20% enriched Uranium and produce HANARO fuel commercially, and also to establish the advanced common research equipment essential for the research on advanced fuel development. For this purpose, this research works were performed for the settlement of radiation protection system and facility special equipment for the FTDF, and the advanced common research equipment for the fuel fabrication and research. As a result, 11 kinds of radiation protection systems such as criticality detection and alarm system, 5 kinds of facility special equipment such as environmental pollution protection system and 5 kinds of common research equipment such as electron-beam welding machine were established. By the settlement of exclusive domestic facility for the research of advanced fuel, the fabrication and supply of HANARO fuel is possible and also can export KAERI-invented centrifugal dispersion fuel materials and its technology to the nations having research reactors in operation. For the future, the utilization of the facility will be expanded to universities, industries and other research institutes

  13. Similarity principles for equipment qualification by experience

    International Nuclear Information System (INIS)

    Kana, D.D.; Pomerening, D.J.

    1988-07-01

    A methodology is developed for seismic qualification of nuclear plant equipment by applying similarity principles to existing experience data. Experience data are available from previous qualifications by analysis or testing, or from actual earthquake events. Similarity principles are defined in terms of excitation, equipment physical characteristics, and equipment response. Physical similarity is further defined in terms of a critical transfer function for response at a location on a primary structure, whose response can be assumed directly related to ultimate fragility of the item under elevated levels of excitation. Procedures are developed for combining experience data into composite specifications for qualification of equipment that can be shown to be physically similar to the reference equipment. Other procedures are developed for extending qualifications beyond the original specifications under certain conditions. Some examples for application of the procedures and verification of them are given for certain cases that can be approximated by a two degree of freedom simple primary/secondary system. Other examples are based on use of actual test data available from previous qualifications. Relationships of the developments with other previously-published methods are discussed. The developments are intended to elaborate on the rather broad revised guidelines developed by the IEEE 344 Standards Committee for equipment qualification in new nuclear plants. However, the results also contribute to filling a gap that exists between the IEEE 344 methodology and that previously developed by the Seismic Qualification Utilities Group. The relationship of the results to safety margin methodology is also discussed. (author)

  14. Seismic verification of nuclear plant equipment anchorage

    International Nuclear Information System (INIS)

    Lepiece, M.; Van Vyve, J.

    1991-01-01

    More than 60% of the electrical power of Belgium is generated by seven PWR nuclear power plants. For three of them, the electro-mechanical equipment had to be reassessed after ten years of operation, because the seismic requirements were upgraded from 0.1 g to 0.17 g free field ground acceleration. The seismic requalification of the active equipment was a critical problem as the classical methods were too conservative. The approach based on the use of the past experience on the seismic behavior of nonnuclear equipment, chosen and developed by the SQUG, had to be transposed to the Belgian N.P.P. The decision of the accept-ability of equipment relies heavily on the aseismatic capacity of anchorage. The Electrical Power Research Institute (EPRI) developed the procedure and guideline for the demonstration of the aseismatic adequacy of equipment anchorage in a cost-effective and consistent manner, to support the decision by Seismic Review Team. The field inspection procedure to identify the type of fasteners and detect their possible defects and the verification procedure developed to calculate the aseismatic capacity of equipment anchorage on the strength of fasteners, the aseismatic capacity of anchorage and the comparison of the capacity with the demand are reported. (K.I.)

  15. Development of remote handling tools and equipment

    International Nuclear Information System (INIS)

    Nakahira, Masataka; Oka, Kiyoshi; Taguchi, Kou; Ito, Akira; Fukatsu, Seiichi; Oda, Yasushi; Kajiura, Soji; Yamazaki, Seiichiro; Aoyama, Kazuo.

    1997-01-01

    The remote handling (RH) tools and equipment development in ITER focuses mainly on the welding and cutting technique, weld inspection and double-seal door which are essential factors in the replacement of in-vessel components such as divertor and blanket. The conceptual design of these RH tools and equipment has been defined through ITER engineering design activity (EDA). Similarly, elementary R and D of the RH tools and equipment have been extensively performed to accumulate a technological data base for process and performance qualification. Based on this data, fabrications of full-scale RH tools and equipment are under progress. A prototypical bore tool for pipe welding and cutting has already been fabricated and is currently undergoing integrated performance tests. This paper describes the design outline of the RH tools and equipment related to in-vessel components maintenance, and highlights the current status of RH tools and equipment development by the Japan Home Team as an ITER R and D program. This paper also includes an outline of insulation joint and quick-pipe connector development, which has also been conducted through the ITER R and D program in order to standardize RH operations and components. (author)

  16. 7 CFR 58.229 - Filler and packaging equipment.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Filler and packaging equipment. 58.229 Section 58.229....229 Filler and packaging equipment. All filling and packaging equipment shall be of sanitary... equipment should comply with the 3-A Sanitary Standards for equipment for Packaging Dry Milk and Dry Milk...

  17. 46 CFR 108.719 - Pilot boarding equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Pilot boarding equipment. 108.719 Section 108.719... AND EQUIPMENT Miscellaneous Equipment § 108.719 Pilot boarding equipment. (a) This section applies to... vessel must have suitable pilot boarding equipment available for use on each side of the vessel. If a...

  18. 46 CFR 109.347 - Pilot boarding equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Pilot boarding equipment. 109.347 Section 109.347... OPERATIONS Operation and Stowage of Safety Equipment § 109.347 Pilot boarding equipment. (a) The master or person in charge shall ensure that pilot boarding equipment is maintained as follows: (1) The equipment...

  19. 46 CFR 77.40-1 - Pilot boarding equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Pilot boarding equipment. 77.40-1 Section 77.40-1... MISCELLANEOUS SYSTEMS AND EQUIPMENT Pilot Boarding Equipment § 77.40-1 Pilot boarding equipment. (a) This... vessel. (b) Each vessel must have suitable pilot boarding equipment available for use on each side of the...

  20. 7 CFR 3015.167 - Replacement of equipment.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Replacement of equipment. 3015.167 Section 3015.167..., DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Property § 3015.167 Replacement of equipment. (a) If needed, equipment may be exchanged for replacement equipment. Replacement of equipment may be...

  1. 46 CFR 180.175 - Survival craft equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Survival craft equipment. 180.175 Section 180.175... TONS) LIFESAVING EQUIPMENT AND ARRANGEMENTS Survival Craft Arrangements and Equipment § 180.175 Survival craft equipment. (a) General. Each item of survival craft equipment must be of good quality, and...

  2. 14 CFR 135.173 - Airborne thunderstorm detection equipment requirements.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne thunderstorm detection equipment... Aircraft and Equipment § 135.173 Airborne thunderstorm detection equipment requirements. (a) No person may... the aircraft is equipped with either approved thunderstorm detection equipment or approved airborne...

  3. Equipment installation structure of roof slab for tank type FBR and method of equipment installation

    International Nuclear Information System (INIS)

    Sakai, Takao; Yamakawa, Masanori; Otsuka, Masaya; Sekine, Katsuhisa

    1986-01-01

    Purpose: To reduce equipment thermal stress and deformation by eliminating uneven temperature distribution caused at the equipment through section of the roof slab for the tank FBR, and at the same time, simplify the structure installation. Method: Multiple number of vertical fin projects are fit on the equipment through-section inside wall for the roof slab and the cylindrical equipment peripheral wall, and with these projected fins, the ring space of the through section is vertically divided into multiple sections in the circumferential direction. The vertical fins on the through-section inside wall and the fins on the equipment peripheral wall are contacted with each other by revolving them in the lateral direction. As a result, the natural convection caused by the difference of temperatures in the vertical direction of the ring space becomes a convection within each sector divided, and never generates circumferential circulation, which reduce uneven temperature distribution caused at the equipment through section. (Kawakami, Y.)

  4. Environmental/dynamic mechanical equipment qualification and dynamic electrical equipment qualification program (EDQP)

    International Nuclear Information System (INIS)

    Hunter, J.A.

    1984-01-01

    Equipment qualification research is being conducted to investigate acceptable criteria, requirements, and methodologies for the dynamic (including seismic) and environmental qualification of mechanical equipment and for the dynamic (including seismic) qualification of electrical equipment. The program is organized into three elements: (1) General Research, (2) Environmental Research, and (3) Dynamic Research. This paper presents the highlights of the results to date in these three elements of the program

  5. PROBLEMS PERTAINING TO DIVERSIFICATION OF CIVIL EQUIPMENT IN EQUIPMENT OF MILITARY PURPOSE

    OpenAIRE

    A. I. Kotlabay; V. A. Korobkin; V. F. Tamelo; I. V. Kostko; S. V. Kondratiev

    2009-01-01

    Study of directions concerning development of military equipment, its modernization with the purpose to improve its military efficiency is an actual problem for the Armed Forces, military science, designers and researchers.The paper analyzes and estimates possibilities to use civil equipment for military purpose. Problems pertaining to technologies of double application, diversification of civil equipment in military engineering machinery are considered in the paper.

  6. Use of Equipment Information System (EQUIS) to determine priority for purchasing safeguards equipment

    International Nuclear Information System (INIS)

    Silberberg, S.

    1988-01-01

    To manage its large world-wide inventory of safeguards equipment, the IAEA Safeguards department uses a computerized Equipment Information System (EQUIS). EQUIS data have been analyzed using Queueing Theory to determine if inventory is adequate to meet inspector demands and in those cases where it is inadequate, to indicate how many additional units should be procured. Results are tabulated for various types of non-destructive analysis (NDA) equipment. For equipment where there is a high turnover and hence a large amount of data, the analysis provides a powerful tool for assisting procurement decisions

  7. Non-Destructive Inspection Methods for Propulsion Systems and Components

    Science.gov (United States)

    1979-04-01

    tandis qu’une piice samne restera, silencieuse. 11 est alora possible de concevoir des proc4- dures industrielles d’acceptation ou rejet . Le C.E.T.I.H. a...rdalisation do coon turbomachine. ou noteurs thermiques do hauto. perfomance. ndce..ite l& miss on oeuvre do matdriaux at techniques de plus en plus...Instruments lea plum avances actuoliomont pour traitor lea problimes industriels d’~mimmion aconstique. IIAt/ Localimation La localimation eat mimple

  8. The effect of surface roughness on the heat exchange and pressure-drop coefficients; Influence des rugosites de paroi sur les coefficients d'echange thermique et de perte de charge

    Energy Technology Data Exchange (ETDEWEB)

    Malherbe, J M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-02-15

    The effect of various types of roughness on the wall of an axial tube in an annular space of 15-25 mm cooled by an air-flow has been studied in the case of steady turbulence. Roughness of the type 'disrupter of the boundary layer' was set up using triangular threads of 0.2 to 0.4 mm thickness machined in the tube itself, or brass or glass wire wound on a smooth tube. Tests were also carried out using the roughness provided by regularly spaced pyramids 0.4 mm high. The results obtained showed that the heat exchange increased because of the presence of this roughness. A maximum in the heat exchange and pressure-drop coefficients was observed when the pitch equals about eight times the height of the thread. An analytical method has been developed and experiments have been carried out in which the two walls of the annular space were heated in such a way as to transmit unequal heat flows. The region considered is limited to Reynolds's numbers of between 5 X 10{sup 3} and 5 x 10{sup 4} and wall temperatures of under 250 deg C. (author) [French] L'effet de diverses rugosites sur la paroi du tube central d'un espace annulaire de diametre 15-25 mm refroidi par un ecoulement d'air a ete etudie en regime turbulent etabli. Des rugosites du type 'interrupteur de couche limite' etaient realisees au moyen de filets triangulaires, de 0,2 a 0,4 mm de hauteur usines dans l'epaisseur du tube ou de fils de laiton, ou de verre, enroules sur un tube lisse. Les essais ont porte egalement sur des rugosites constituees par des pyramides de 0,4 mm de hauteur et regulierement espacees. Les resultats obtenus ont mis en evidence une augmentation de transfert de chaleur due a la presence des elements rugueux. L'existence d'un maximum pour les coefficients d'echange thermique et de perte de charge a ete constate lorsque le pas atteint huit fois la hauteur des rugosites. Une methode analytique a ete etablie et des experiences ont ete realisees au cours desquelles les deux parois de l

  9. Methodology for assessing laser-based equipment

    Science.gov (United States)

    Pelegrina-Bonilla, Gabriel; Hermsdorf, Jörg; Thombansen, Ulrich; Abels, Peter; Kaierle, Stefan; Neumann, Jörg

    2017-10-01

    Methodologies for the assessment of technology's maturity are widely used in industry and research. Probably the best known are technology readiness levels (TRLs), initially pioneered by the National Aeronautics and Space Administration (NASA). At the beginning, only descriptively defined TRLs existed, but over time, automated assessment techniques in the form of questionnaires emerged in order to determine TRLs. Originally TRLs targeted equipment for space applications, but the demands on industrial relevant equipment are partly different in terms of, for example, overall costs, product quantities, or the presence of competitors. Therefore, we present a commonly valid assessment methodology with the aim of assessing laser-based equipment for industrial use, in general. The assessment is carried out with the help of a questionnaire, which allows for a user-friendly and easy accessible way to monitor the progress from the lab-proven state to the application-ready product throughout the complete development period. The assessment result is presented in a multidimensional metric in order to reveal the current specific strengths and weaknesses of the equipment development process, which can be used to direct the remaining development process of the equipment in the right direction.

  10. Characterization equipment essential/support drawing plan

    International Nuclear Information System (INIS)

    WILSON, G.W.

    1999-01-01

    The purpose of this document is to list the Characterization equipment drawings that are classified as Essential Drawings and Support Drawings. Essential Drawings: Are those drawings identified by the facility staff as necessary to directly support the safe operation of the facility or equipment (HNF 1997a). Support Drawings: Are those drawings identified by facility staff that further describe the design details of structures, systems, or components shown on essential drawings. (HNF 1997a) The Characterization equipment drawings identified in this report are deemed essential drawings as defined in HNF-PRO-242, Engineering Drawing Requirements (HNF 1997a). These drawings will be prepared, revised, and maintained per HNF-PRO-440, Engineering Document Change Control (HNF 1997b). All other Characterization equipment drawings not identified in this document will be considered General drawings until the Characterization Equipment Drawing Evaluation Report (Wilson 1998) is updated during fiscal year 1999. Trucks 1 and 2 drawings are not included in this revision of the essential drawing list due to uncertainty about future use

  11. Diagnostic imaging and radiation therapy equipment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-05-01

    This is the third edition of CSA Standard C22.2 No. 114 (now CAN/CSA-C22.2 No. 114), which is one of a series of standards issued by the Canadian Standards Association under Part II of the Canadian Electrical Code. This edition marks an important shift towards harmonization of Canadian requirements with those of the European community and the United States. Also important to this edition is the expansion of its scope to include the complete range of diagnostic imaging and radiation therapy equipment, rather than solely radiation-emitting equipment. In so doing, equipment previously addressed by CSA Standard C22.2 No. 125, Electromedical Equipment, specifically lasers for medical applications and diagnostic ultrasound units, is now dealt with in the new edition. By virtue of this expanded scope, many of the technical requirements in the electromedical equipment standard have been introduced to the new edition, thereby bringing CSA Standard C22.2 No. 114 up to date. 14 tabs., 16 figs.

  12. Diagnostic imaging and radiation therapy equipment

    International Nuclear Information System (INIS)

    1990-05-01

    This is the third edition of CSA Standard C22.2 No. 114 (now CAN/CSA-C22.2 No. 114), which is one of a series of standards issued by the Canadian Standards Association under Part II of the Canadian Electrical Code. This edition marks an important shift towards harmonization of Canadian requirements with those of the European community and the United States. Also important to this edition is the expansion of its scope to include the complete range of diagnostic imaging and radiation therapy equipment, rather than solely radiation-emitting equipment. In so doing, equipment previously addressed by CSA Standard C22.2 No. 125, Electromedical Equipment, specifically lasers for medical applications and diagnostic ultrasound units, is now dealt with in the new edition. By virtue of this expanded scope, many of the technical requirements in the electromedical equipment standard have been introduced to the new edition, thereby bringing CSA Standard C22.2 No. 114 up to date. 14 tabs., 16 figs

  13. Design by analysis of composite pressure equipment

    International Nuclear Information System (INIS)

    Durand, S.; Mallard, H.

    2004-01-01

    Design by analysis has been particularly pointed out by the european pressure equipment directive. Advanced mechanical analysis like finite element method are used instead of classical design by formulas or graphs. Structural behaviour can be understood by the designer. Design by analysis of metallic pressure equipments is widely used. Material behaviour or limits analysis is based on sophisticated approach (elasto-plastic analysis,..). Design by analysis of composite pressure equipments is not systematically used for industrial products. The difficulty comes from the number of information to handle. The laws of mechanics are the same for composite materials than for steel. The authors want to show that in design by analysis, the composite material approach is only more complete than the metallic approach. Mechanics is more general but not more complicated. A multi-material approach is a natural evolution of design by analysis of composite equipments. The presentation is illustrated by several industrial cases - composite vessel: analogy with metallic calculations; - composite pipes and fittings; - welding and bounding of thermoplastic equipments. (authors)

  14. Resistance welding equipment manufacturing capability for exports

    Energy Technology Data Exchange (ETDEWEB)

    Sastry, V.S.; Raju, Y.S.; Somani, A.K.; Setty, D.S.; Rameswara Raw, A.; Hermantha Rao, G.V.S.; Jayaraj, R.N. [Nuclear Fuel Complex, Dept. of Atomic Energy, Hyderbad (India)

    2010-07-01

    Indian Pressurised Heavy Water Reactor (PHWR) fuel bundle is fully welded and is unique in its design. Appendage welding, end closure welding, and end plate welding is carried out using resistance welding technique. Out of many joining processes available, resistance-welding process is reliable, environment friendly and best suitable for mass production applications. Nuclear Fuel Complex (NFC), an industrial unit is established in Hyderabad, under the aegis of the Dept of Atomic Energy to manufacture fuel for Pressurised Heavy Water Reactors. From inception, NFC has given importance for self-reliance and indigenization with respect to manufacturing process and equipment. Sintering furnaces, centreless grinders, appendage-welding machines, end-closure welding equipment and end-plate welding equipments, which were initially imported, are either indigenized or designed and manufactured in house. NFC has designed, manufactured a new appendage-welding machine for manufacturing 37 element fuel bundles. Recently NFC has bagged an order from IAEA through international bidding for design, manufacture, supply, erection and commissioning of end-closure welding equipment. The paper gives in detail the salient features of these welding equipment. (author)

  15. A Computerized Procedure linked to Virtual Equipment

    International Nuclear Information System (INIS)

    Jung, Yeon Sub; Song, Tae Young

    2011-01-01

    Digital, information, and communication technologies have change human's behavior. This is because human has limitation to memorize and process information. Human has to access other information and real time information for important decisions. Those technologies are playing important roles. Nuclear power plants cannot be exception. Many accidents in nuclear power plants result from absent or incorrect information. The information for nuclear personnel is context sensitive. They don't have enough time to verify the context sensitive information. Therefore they skip the information, as resulting in incident. Nuclear personnel are usually carrying static paper procedures during local task performance. The procedure guides them steps to follow. There is, however, no dynamic and context sensitive information in the paper. The effect of the work is evaluated once while getting permission of the work. Afterward they are not informed. The static paper is generally simplified, so that it does not show detail of equipment being manipulated. Particularly novice workers feel difficult to understand the procedure due to lack of detail. Pictures of equipment inserted in the procedure are not enough for comprehension. A computerized procedure linked with virtual equipment is one of the best solutions to increase the detail of procedure. Virtual equipment, however, has still limitation not to provide real time information, because the virtual equipment is not synchronized with real plants

  16. 18 CFR 367.3980 - Account 398, Miscellaneous equipment.

    Science.gov (United States)

    2010-04-01

    ... service company's operations that are not included in any other account of this system of accounts. (b... equipment. (3) Employees' recreation equipment. (4) Radios. (5) Restaurant equipment. (6) Soda fountains. (7...

  17. Lessons learned in testing of Safeguards equipment

    International Nuclear Information System (INIS)

    Pepper, Susan; Farnitano, Michael; Carelli, Joseph

    2001-01-01

    Full text: During the 1990s, the IAEA Department of Safeguards began a transition from analog to digital equipment. This included surveillance equipment, seals, NDA measurement systems, and other instruments. The transition to digital equipment was intended to facilitate compatibility between and integration of instruments, remote communication of data, improved data storage, and modernization. Many of the instruments are designed to operate on battery power during loss of facility power, and therefore, are designed to consume minimal power. In 2000, the IAEA experienced a number of failures in digital image surveillance (DIS) equipment. A study of the performance data revealed that the failures occurred in 'high risk' environments where the systems were exposed to neutrons. As a supporter of IAEA equipment development and implementation, the U.S. Support Program worked with the IAEA, the equipment designer, and the equipment manufacturer in special meetings on DIS to determine the cause of the failures. It was as a result of these meetings that single event upset (SEU) was determined to be the root cause of the failures. The meeting participants also identified a list of actions to improve the reliability of DIS systems. As a result of the DIS meetings and the identified actions, the U.S. Support Program approved a request from the IAEA and established Task E.125, 'Remote Monitoring and Unattended Digital Surveillance Systems.' This task is an umbrella task intended to provide a mechanism for response to IAEA needs related to improving the reliability of unattended, remote monitoring and DIS equipment. Subtasks approved under this task include: E.125.1, 'SDIS Software Consolidation and DCM-14 Audit' - This subtask involves the consolidation of a number of individual upgrades to the SDIS and review of the DCM-14 software. As the sponsor of the design of the DCM-14 by Dr. Neumann, the German Support Program is also a participant in this subtask; E.125.2, 'DIS

  18. EPERC: The European Pressure Equipment Research Council

    International Nuclear Information System (INIS)

    Darlaston, J.; McAllister, S.

    1998-01-01

    The European Pressure Equipment Research Council (EPERC) is a European Network of industries, research laboratories, inspection bodies and governmental institutions set up to foster co-operative research for the greater benefit of the European industry. The concept of a European Research Council originated at the PVRC meeting in Cannes in 1989 and since this time volunteers from the industry, research laboratories and of the European Commission Joint Research Centre, Petten have worked together to create a Statute for EPERC. In the context of the pressure equipment industry, the creation of EPERC is extremely pertinent, since in the near future, a Council directive on pressure equipment will replace the existing national regulations. In parallel to this, work is in progress for the elaboration of European Standards. It is useful to recall that ''Harmonised Standards'' will be the privileged means of complying with the Essential Safety Requirements of the directive. (author)

  19. Development of nuclear equipment qualification technology

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Heon O; Kim, Wu Hyun; Kim, Jin Wuk; Kim, Jeong Hyun; Lee, Jeong Kyu; Kim, Yong Han; Jeong, Hang Keun [Korea Institute of Machinery and Materials, Taejon (Korea)

    1999-03-01

    In order to enhance testing and evaluation technologies, which is one of the main works of the Chanwon branch of KIMM(Korea Institute of Machinery and Materials), in addition to the present work scope of the testing and evaluation in the industrial facilities such as petroleum and chemical, plants, the qualification technologies of the equipments important to safety used in the key industrial facilities such as nuclear power plants should be localized: Equipments for testing and evaluation is to be set up and the related technologies must be developed. In the first year of this study, of vibration aging qualification technologies of equipments important to safety used in nuclear power plants have been performed. (author). 27 refs., 81 figs., 17 tabs.

  20. Optimization on replacement period of plant equipment

    International Nuclear Information System (INIS)

    Kasai, Masao; Asano, Hiromi

    2002-01-01

    Optimization of the replacement period of plant equipment is one of the main items to rationalize the activities on plant maintenance. There are several models to replace the equipment and the formulations for optimizing the replacement period are different among these models. In this study, we calculated the optimum replacement periods for some equipment parts based on the replacement models and found that the optimum solutions are not so largely differ from the replacement models as far as the replacement period is not so large. So we will be able to use the most usable model especially in the early phase of rationalization on plant maintenance, since there are large uncertainties in data for optimization. (author)

  1. Maintenance and fabrication of electronic equipment

    International Nuclear Information System (INIS)

    Chung, Chong Eun; Moon, Byung Soo; Hong, Suk Boong; Kim, Yong Keun; Kim, Jung Bok

    2003-12-01

    Development of radiation monitoring equipment could be the base of domestic development of RMS. And the technique could be adapted to development of other radiation equipment of KAERI as well as hospitals and nuclear power plants. The RMS technology could be adapted to the development of precision instruments related to nuclear radiation and be the base of fundamental technology such as protein structure analysis of bio technology, development of nano advanced material and aircraft material. The technology of multi-channel readout ASIC for nuclear radiation detector, which has been imported from abroad, could be adapted to development of radiation equipment for image processing, position of detection, NDT etc., and also the technique will be expected to contribute to increase the use of radiation technology to industrial applications

  2. Methods of equipment choice in shotcreting

    Science.gov (United States)

    Sharapov, R. R.; Yadykina, V. V.; Stepanov, M. A.; Kitukov, B. A.

    2018-03-01

    Shotcrete is widely used in architecture, hydraulic engineering structures, finishing works in tunnels, arc covers and ceilings. The problem of the equipment choice in shotcreting is very important. The main issues influencing the equipment choice are quality improvement and intensification of shotcreting. Main parameters and rational limits of technological characteristic of machines used in solving different problems in shotcreting are described. It is suggested to take into account peculiarities of shotcrete mixing processes and peculiarities of applying these mixtures with compressed air kinetic energy. The described method suggests choosing a mixer with the account of energy capacity, Reynolds number and rotational frequency of the mixing drum. The suggested choice procedure of the equipment nomenclature allows decreasing exploitation costs, increasing the quality of shotcrete and shotcreting in general.

  3. Equipment for light therapy BIOFIE family

    International Nuclear Information System (INIS)

    Corcho Corcho, C. A.; Perez Garcia, A.; Herrera Rodriguez, R.

    2016-01-01

    The development experienced in the design and implementation of equipment are presented, within the subject matter of the application of low level laser and also them LED of high efficiency with therapeutic purposes in health and also in animal health, besides, the use of this technology for this application in agriculture. All the equipment that show up has been developed for the Dpto. of Bioengineer of High Politechnical Institute Jose A. Echeverria (CUJAE) in association with Dpto. of Prototypes of the same institution, under the trademark BIOFIE. Like fundamental and innovative characteristic we can make a comment that all equipment destined to health and animal health, work on continuos and modulated signal mode, using in this mode different bio frequencies. (Author)

  4. Development of superconducting equipment for fusion device

    International Nuclear Information System (INIS)

    Konno, Masayuki; Ueda, Toshio; Hiue, Hisaaki; Ohgushi, Kouzou

    1993-01-01

    At Fuji Electric Co., Ltd., the development of superconductivity was started from 1960, and superconducting equipment for fusion device has been developed for ten years. The superconducting equipment, which is developed for fusion by Fuji Electric Co., Ltd., are able to be grouped in three categories which are current lead, superconducting coil and superconducting bus-line. The current lead is an electrical feeder between a superconducting coil and an electrical power supply. The rated current of developed current lead is 30kA at continuous use and 100kA at short time use respectively. The advanced disk type coil is developed for the toroidal field coil and some coils are developed for critical current measurement. Superconductor is applied to the superconducting bus-line between the superconducting coils and the current leads, and the bus-line is being developed for the Large Helical Device. This report describes an abstract of these equipment. (author)

  5. LESSONS LEARNED IN TESTING OF SAFEGUARDS EQUIPMENT

    International Nuclear Information System (INIS)

    Pepper, S.; Farnitano, M.; Carelli, J.; Hazeltine, J.; Bailey, D.

    2001-01-01

    The International Atomic Energy Agency's (IAEA) Department of Safeguards uses complex instrumentation for the application of safeguards at nuclear facilities around the world. Often, this equipment is developed through cooperation with member state support programs because the Agency's requirements are unique and are not met by commercially available equipment. Before approving an instrument or system for routine inspection use, the IAEA subjects it to a series of tests designed to evaluate its reliability. In 2000, the IAEA began to observe operational failures in digital surveillance systems. In response to the observed failures, the IAEA worked with the equipment designer and manufacturer to determine the cause of failure. An action plan was developed to correct the performance issues and further test the systems to make sure that additional operational issues would not surface later. This paper addresses the steps taken to address operation issues related to digital image surveillance systems and the lessons learned during this process

  6. Consolidation equipment for irradiated nuclear fuel channels

    International Nuclear Information System (INIS)

    Taguchi, M.; Komatsu, Y.; Ose, T.

    1989-01-01

    The authors have developed and put into use a new type of mechanical consolidation equipment for irradiated nuclear fuel channels. This includes round-slice cutting of the top 100mm of the fuel channel with a guillotine cutter, and press cutting of the two corners of the remaining length of the fuel channel. Four guillotine blades work in combination with receiving blades arranged inside the fuel channel to cut the top 100mm, including the clips and spacers, of the fuel channel into a round slice. A press assembled in the consolidation equipment then presses the slice to achieve volume reduction. The press cutting operation uses two press cutting blades arranged inside the fuel channel and the receiving blades outside the fuel channel. The remaining length of fuel channel is cut off into L-shaped pieces by press cutting. This consolidation equipment is highly efficient because the round-slice cutting, pressing, and press cutting are all achieved by one unit

  7. Equipment support for the implementation of safeguards

    International Nuclear Information System (INIS)

    Arlt, R.; Bosler, G.; Goldfarb, M.; Schanfein, M.; Whichello, J.

    2001-01-01

    Full text: The provision of effective, reliable, and user-friendly equipment needed for the implementation of safeguards is one of the main objectives of the Division of Technical Services (SOTS) in the Department of Safeguards. As an outcome of a review by an independent external consultant firm, the instrumentation sections of the SGTS were reorganized in January 2001 into two new sections, the Section for NDA Systems and Seals (TNS) and Section for Installed Systems (TIE). Each section has 'cradle-to-grave' responsibilities for development, implementation, maintenance, and decommissioning of safeguards instruments and measurement systems. Unattended assay, monitoring and surveillance instruments are the responsibility of TIE while attended nondestructive assay (NDA) instruments and seals are handled by TNS. The principal goals of both sections are to define equipment requirements based on Departmental needs, to coordinate Support Programme tasks concerning development and implementation activities, to provide system engineering of commercial components, manage laboratory and to do field testing and prove system suitability for defined safeguards applications. In addition both sections coordinate equipment and supply needs for the Department, including acquisition, preparation, servicing, installation, commissioning, troubleshooting, maintenance and repair, ensuring their availability when needed. As required, TIE and TNS provide specialized field support to the Operations Divisions. Each section is working to standardize equipment as much as possible and reduce the number of instruments performing the same function. This reduces both inspector and technician training, required parts inventories, and overall life-cycle costs. Development based on User Needs from the Operations Divisions follows a strict quality control program that includes a thorough qualification testing procedure with the last phase being field-testing under actual facility conditions. A

  8. Study of the effect of neutron and electron irradiations on the low temperature thermal conductivity of germanium and silicon; Etude de l'effet des irradiations neutronique et electronique sur la conductibilite thermique aux basses temperatures du germanium et du silicium

    Energy Technology Data Exchange (ETDEWEB)

    Vandevyver, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-06-15

    The main results obtained from this work are the following: 1 Neutron irradiation (at 300 deg. K) produces lattice defects in germanium and silicon, and a corresponding very large lowering of the thermal conductivity is observed in the low temperature region (4-300 ). The results obtained have been explained with the help of the following hypotheses: for silicon a scattering of phonons by the stress fields produced by the defects; for germanium, a supplementary scattering of the electron phonon type. 2 Annealing treatments carried out on these materials above 373 deg. K restored the thermal conductivity over the whole temperature range of the measurements (4-300 deg. K); in the case of both germanium and silicon there were two steps in the annealing process. 3 A study of the thermal conductivity of germanium (initially P or N) after an electronic irradiation showed that the scattering of phonons could depend on the state of charge of the defects thus produced. (author) [French] Les principaux resultats obtenus au cours de ce travail sont les suivants : 1 Les irradiations neutroniques (a 300 deg. K) introduisent des defauts de reseau dans le germanium et le silicium et l'on observe correlativement pour ces materiaux, une tres importante diminution de conductibilite thermique dans le domaine des basses temperatures (4-300 deg. K). Les resultats obtenus ont pu etre interpretes en admettant principalement: pour le silicium, une diffusion des phonons par les champs de contrainte dus aux defauts; pour le germanium, une diffusion additionnelle du type electron-phonon. 2 Des recuits effectues sur ces materiaux au-dessus de 373 deg. K ont montre une restauration de la conductibilite thermique dans tout l'intervalle de temperature de mesure (4-300 deg. K) et comportant pour le germanium et le silicium, deux etapes de recuit 3 L'etude de la conductibilite thermique de germanium (initialement N ou P) apres une irradiation electronique, a montre que la diffusion des phonons

  9. Process plant equipment operation, control, and reliability

    CERN Document Server

    Holloway, Michael D; Onyewuenyi, Oliver A

    2012-01-01

    "Process Plant Equipment Book is another great publication from Wiley as a reference book for final year students as well as those who will work or are working in chemical production plants and refinery…" -Associate Prof. Dr. Ramli Mat, Deputy Dean (Academic), Faculty of Chemical Engineering, Universiti Teknologi Malaysia "…give[s] readers access to both fundamental information on process plant equipment and to practical ideas, best practices and experiences of highly successful engineers from around the world… The book is illustrated throughout with numerous black & white p

  10. Equipment Qualification Data Base user manual

    International Nuclear Information System (INIS)

    Decker, Q.R.; Fackrell, L.J.; Fitch, L.R.; Meeky, O.B.

    1985-09-01

    This manual details the Equipment Qualification Data Base (EQDB), its usage, and contents. The EQDB consists of two files; the Plant Qualification File (PQF) and the Equipment Qualification File (EQF). The PQF contains plant specific environmental data and the EQF contains summaries of various test results. Two data management systems are used to manipulate the data and are discussed in this manual. SAS Institute System 2000 (S2K) is the management system for the PQF and Query Update (QU) is the operating system for the EQF. Each management system contains report writers. These writers and how to use them are discussed in detail in this manual

  11. Risk matrix model for rotating equipment

    Directory of Open Access Journals (Sweden)

    Wassan Rano Khan

    2014-07-01

    Full Text Available Different industries have various residual risk levels for their rotating equipment. Accordingly the occurrence rate of the failures and associated failure consequences categories are different. Thus, a generalized risk matrix model is developed in this study which can fit various available risk matrix standards. This generalized risk matrix will be helpful to develop new risk matrix, to fit the required risk assessment scenario for rotating equipment. Power generation system was taken as case study. It was observed that eight subsystems were under risk. Only vibration monitor system was under high risk category, while remaining seven subsystems were under serious and medium risk categories.

  12. Development of diaphragm automatic homing equipment

    International Nuclear Information System (INIS)

    Kobayashi, Hidetoshi; Yamada, Koji; Moriya, Shinichi; Koike, Jiro; Okabe, Masao; Oyama, Akihiro.

    1996-01-01

    In steam-turbine overhaul inspection, one of the most important processes is to remove rust and deposited contaminants on the surface of turbine parts, while the turbine is in operation, to recover thermal efficiency and prepare good surface conditions for color penetrant inspection. These processes generally are done by dry honing, but this generates dust. To protect laborers against these conditions, Hitachi, Ltd. has developed automatic honing equipment for the diaphragms of the nuclear steam turbine. This equipment was first used in the first annual inspection and overhaul of Hamaoka Nuclear Power Plant No.4 of Chubu Electric Power Inc. (author)

  13. Benefits of Digital Equipment Generic Qualification Activities

    International Nuclear Information System (INIS)

    Thomas, James E.; Steiman, Samuel C.

    2002-01-01

    As a result of nuclear power plant instrumentation and control obsolescence issues, there have been numerous activities during recent years relating to the qualification of digital equipment. Some of these activities have been 'generic' in nature in that the qualification was not limited to plant specific applications, but was intended to cover a broad base of potential applications of the digital equipment. These generic qualifications have been funded by equipment manufacturers and by utility groups and organizations. The generic activities sponsored by the Electric Power Research Institute (EPRI) have been pilot projects for an overall generic qualification approach. The primary benefit resulting from the generic qualification work to date is that a number of digital platforms and digital devices are now available for use in various nuclear safety-related applications. Many of the tests and evaluations necessary to support plant specific applications have been completed. The amount of data and documentation that each utility must develop on a case by case basis has been significantly reduced. There are also a number of additional benefits resulting from these industry efforts. The challenges and difficulties in qualifying digital equipment for safety-related applications are now more clearly understood. EPRI has published a lessons learned document (EPRI Report 1001452, Generic Qualification of Commercial Grade Digital Devices: Lessons Learned from Initial Pilots, which covers several different qualification areas, including device selection, project planning, vendor surveys and design reviews, and electromagnetic compatibility (EMC) qualification. Application of the experience and lessons learned from the EPRI pilot activities should help reduce the effort and cost required for future qualification work. Most generic qualification activities for commercial equipment have been conducted using the approach of EPRI TR-106439, Guideline on Evaluation and Acceptance

  14. Maintenence and fabrication of Electronic Equipment

    International Nuclear Information System (INIS)

    Chung, Chong Eun; Moon, Byung Soo; Hong, Suk Boong; Kim, Young Keun; Kim, Jung Bok; Lee, Sang Suk

    2004-12-01

    Development of the SPND Monitor could be the base of development of small signal processing circuits and the technique could be used to develop other precision equipment. The repair technology for high purity germanium(HPGe) detector system could be adapted to other areas where high purity detectors are used such as hospitals, universities etc. The technology of multi-channel ASIC for nuclear radiation detector, which has been imported from abroad, could be adapted to development of radiation equipment for image processing, position of detection, NDT etc., and also the technique will be expected to contribute to increase the use of radiation technology to industrial applications

  15. Radiological equipment 'Planmeca' used in dentistry

    International Nuclear Information System (INIS)

    Tuciac, Carolina

    2011-01-01

    Equipment 'Planmeca Pro Max 3D' for volumetric imaging with cone beam examine the patients under computerized tomography considering the rate 0.2-1.0 mm, digital orthopantomography, 3D cephalometry. 3D tomography image facilitates an accurate view of oral structures. It was adopted quickly, and became the basic equipment for all applications in dentistry. The Cone Beam Volumetric Tomography (CBVT), Planmeca Pro Max 3D model give the opportunity to obtain great radiological information very important for the dentist decision. (author)

  16. Conceptual design report, CEBAF basic experimental equipment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-04-13

    The Continuous Electron Beam Accelerator Facility (CEBAF) will be dedicated to basic research in Nuclear Physics using electrons and photons as projectiles. The accelerator configuration allows three nearly continuous beams to be delivered simultaneously in three experimental halls, which will be equipped with complementary sets of instruments: Hall A--two high resolution magnetic spectrometers; Hall B--a large acceptance magnetic spectrometer; Hall C--a high-momentum, moderate resolution, magnetic spectrometer and a variety of more dedicated instruments. This report contains a short description of the initial complement of experimental equipment to be installed in each of the three halls.

  17. RPC industries - UV and EB equipment manufacturers

    International Nuclear Information System (INIS)

    Rodrigues, A.M.

    1987-01-01

    RPC Industries has been manufacturing electron beam and ultraviolet equipment for the industrial processing of materials for more than 15 years. RPC maintains its headquarters and electron processor manufacturing plant in Hayward, California. UV equipment is made in the company's plant near Chicago. Sales offices are maintained in New York, Illinois, and California in the USA, and in Germany, Japan, Australia, Italy, Israel, and Sweden. Complete testing and pilot facilities are available in Hayward (EB) and near Chicago (UV). Described below are the basic system components, applications and advantages of RPC's UV and EB systems. (orig.)

  18. Improvements in remote equipment torquing and fastening

    International Nuclear Information System (INIS)

    Garin, J.

    1978-01-01

    Remote torquing and fastening is a requirement of generic interest for application in an environment not readily accessible to man. The developments over the last 30 years in torque-controlled equipment above 200 nm (150 ft/lb) have not been emphasized. The development of specialized subassemblies to torque and fasten equipment in a remotely controlled environment is an integral part of the Advanced Fuel Recycle Program at Oak Ridge National Laboratory. Commercially available subassemblies have been adapted into a system that would provide remote torquing and fastening in the range of 200 to 750 nm (150 to 550 ft/lb). 9 figures

  19. The Cyrano program. 1 - description and operation of an irradiation device 'Cyrano'. 2 - results of the experiments Cyrano 1 and 2 (study of the EL 4 first-bach pencil); measurement of the thermal conductivity integral for UO{sub 2} sintered up to 2300 deg C; evolution of fission gases at constant power; Programme Cyrano. 1 - description et exploitation d'un dispositif d'irradiation ''cyrano''. 2 - resultats des experiences cyrano 1 et 2 (etude du crayon EL4 1. jeu). Mesure de l'integrale de conductibilite thermique d'UO{sub 2} fritte jusqu'a 2300 deg C. Evolution des gaz de fission a puissance constante

    Energy Technology Data Exchange (ETDEWEB)

    Stora, J P; Chenebault, P [Commissariat a l' Energie Atomique, 91 - Saclay (France). Centre d' Etudes Nucleaires

    1968-07-01

    Two rods of the type 'EL 4 first score' have been irradiated in 'Cyrano' capsules which are suited for continuous measurement of the nuclear power evolved and equipped with thermocouples. The variations of the integral of conductivity of sintered 96 per cent theoretical dense UO{sub 2} has been established until 2300 deg. C; these variations are coherent with those previously measured out-of-pile. The released fission gases have been recovered at different times during the irradiation: the kinetics of release of stable gases is such that, in the experimental conditions (T{sub surface} = 610 deg. C, {integral}{sub T{sub s}}{sup T{sub c}} kdT = 34.7 W cm{sup -1}) the fraction of released gases is still widely increasing after 12 days of irradiation. Numerous observations have been made on concentrations of rare gases locally present in the irradiated fuel. (authors) [French] L'irradiation de deux crayons combustibles type EL 4, 1er jeu, a ete menee a bien dans des capsules 'Cyrano' equipees de dispositifs de mesure continue de la puissance nucleaire et de plusieurs reperes de temperatures; la variation de l'integrale de conductibilite thermique de l'oxyde d'uranium fritte (96 pour cent d. th.) a ete tracee jusqu'a 2300 deg. C; la courbe representative de ces variations est coherente avec celle obtenue precedemment hors pile. Les gaz de fission apparus hors du combustible ont ete extraits du crayon a plusieurs reprises pendant l'experience: la cinetique d'accumulation des gaz stables est telle que dans les conditions etudiees (T{sub surface} = 610 deg. C, {integral}{sub T{sub s}}{sup T{sub c}} kdT = 34.7 W cm{sup -1}) la fraction des gaz degages est encore largement croissante apres 12 jours d'irradiation. De nombreuses observations ont ete recueillies sur la nature et la concentration des gaz rares presents en differents points du combustible irradie. (auteurs)

  20. Seismic qualification of non-safety class equipment whose failure would damage safety class equipment

    International Nuclear Information System (INIS)

    LaSalle, F.R.

    1991-01-01

    Both Code of Federal Regulations, Title 10, Part 50, and US Department of Energy Order 6340.1A have requirements to assess the interaction of non-safety and safety class structures and equipment during a seismic event to maintain the safety function. At the Hanford Site, a cost effective program has been developed to perform the evaluation of non-safety class equipment. Seismic qualification is performed by analysis, test, or upgrading of the equipment to ensure the integrity of safety class structures and equipment. This paper gives a brief overview and synopsis that address design analysis guidelines including applied loading, damping values, component anchorage, allowable loads, and stresses. Test qualification of equipment and walkdown acceptance criteria for heating ampersand ventilation (H ampersand V) ducting, conduit, cable tray, missile zone of influence, as well as energy criteria are presented

  1. Production of Olefins and Higher Hydrocarbons by Thermal Coupling of Methane Production d'oléfines et d'hydrocarbures supérieurs par couplage thermique du méthane

    Directory of Open Access Journals (Sweden)

    Weill J.

    2006-11-01

    Full Text Available Thermal coupling of methane or methane pyrolysis, which is a possible way for the direct chemical conversion of natural gas, can be used to produce ethylene, acetylene and benzene. But the high stability of methane requires a very high pyrolysis temperature (1200°C. To perform this reaction, IFP decided to build and elecric pilot furnace with an overall capacity of 10 m3/h. The design of this furnace is based on shell-and-tube heat exchanger technology with the use of new materials such as ceramics. This furnace has now been operating for more than one year without any noteworthy incident. First we will describe the technological and parametric study that has now been completed. In conclusion, we will make a short economic assessment of the production of ethylene and acetylene in France. Dans le domaine de la conversion du gaz naturel en hydrocarbures supérieurs, il nous a paru intéressant de reconsidérer la pyrolyse du méthane. Contrairement au couplage oxydant [1, 2], il s'agit d'une réaction très ancienne [3] n'ayant fait l'objet que de travaux épisodiques dans le passé [4, 5]. En effet, compte-tenu de sa réactivité très faible, le méthane doit être porté à très haute température, de l'ordre de 1 200°C, pour produire par couplage thermique principalement de l'éthylène de l'acétylène, du benzène, du coke et de l'hydrogène. Ce qui a gouverné notre démarche et la reprise de travaux sur cette réaction, était l'idée que les nouvelles technologies et spécialement les nouveaux matériaux réfractaires tels que les matériaux céramiques devaient permettre de réaliser de nouveaux designs de réacteurs pour mettre en oeuvre cette réaction. Lors d'une étude paramétrique préliminaire [8], réalisée sur un micro-pilote de faible capacité (50 l/h, nous avons pu obtenir des résultats intéressants, parmi lesquels nous avons sélectionné un bilan matière moyen , qui représente un compromis entre les imp

  2. UV Tanning Equipment | Radiation Protection | US EPA

    Science.gov (United States)

    2017-08-07

    Sun lamps and tanning equipment emit ultraviolet (UV) rays. People who are exposed to UV rays over a long period of time are more likely to develop skin cancer. People with light skin are in more danger because their skin is more sensitive to UV rays.

  3. TECHNICAL EQUIPMENT FOR SORTING APPLES BY SIZE

    Directory of Open Access Journals (Sweden)

    Vasilica Ştefan

    2012-01-01

    Full Text Available Need to increase the competitiveness of semi-subsistence farms, by valorisation of the fruits, led to research for designing of an equipment for sorting apples by size, in order to meet market requirement, pricing according to the size of the fruits.

  4. 49 CFR 374.313 - Equipment.

    Science.gov (United States)

    2010-10-01

    .... Each bus (except in commuter service) seating more than 14 passengers (not including the driver) shall..., DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS PASSENGER CARRIER REGULATIONS Adequacy of Intercity Motor Common Carrier Passenger Service § 374.313 Equipment. (a) Temperature control. A...

  5. OEE and equipment effectiveness : an evaluation

    NARCIS (Netherlands)

    Ron, de A.J.; Rooda, J.E.

    2006-01-01

    The overall equipment effectiveness or efficiency (OEE) is a metric that has been accepted in the semiconductor industry. OEE is simple and clear, and standards and guidelines have been developed. Nonetheless, the literature indicates imperfections in applying OEE with regard to the time base and

  6. Maintenance optimization plan for essential equipment reliability

    International Nuclear Information System (INIS)

    Steffen, D.H.

    1996-02-01

    The Maintenance Optimization Plan (MOP) for Essential Equipment Reliability will furnish Tank Waste Remediation System (TWRS) management with a pro-active, forward-thinking process for maintaining essential structures, systems, and components (ESSC) at the Hanford Site tank farms in their designed condition, and to ensure optimum ESSC availability and reliability

  7. EQuIP-ped for Success

    Science.gov (United States)

    Ewing, Molly

    2015-01-01

    The Educators Evaluating the Quality of Instructional Products (EQuIP) Rubric for science is a new tool for science educators that provides criteria by which to examine the alignment and overall quality of lessons and units with respect to the "Next Generation Science Standards" ("NGSS"). The rubric criteria are divided into…

  8. The LHC's equipment all in step

    CERN Multimedia

    2005-01-01

    Over 80% of the control equipment for the LHC will be connected by a special communication network known as WorldFIP, which has been chosen for its very precise timing, excellent operating performance and robustness in difficult environments. Over 350 kilometres of this network are currently being installed in the LHC tunnel and checked for compliance with the required standards.

  9. 7 CFR 3016.32 - Equipment.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Equipment. 3016.32 Section 3016.32 Agriculture Regulations of the Department of Agriculture (Continued) OFFICE OF THE CHIEF FINANCIAL OFFICER, DEPARTMENT OF AGRICULTURE UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND COOPERATIVE AGREEMENTS TO STATE AND LOCAL...

  10. Engineering study of riser equipment contamination

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    This Engineering Study was to evaluate the current equipment and operating procedures to determine if changes could be made to improve ALARA and evaluate the feasibility of implementing the proposed solutions. As part of this study input from the cognizant characterization engineers and operating sampling crews was obtained and evaluated for ALARA improvements

  11. 21 CFR 226.30 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... contamination, including cross-contamination from manufacturing operations. (d) Be suitably grounded... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Equipment. 226.30 Section 226.30 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL...

  12. New Equipping Strategies for Combat Support Hospitals

    Science.gov (United States)

    2010-01-01

    Combat and Doctrine Development and COL Timothy Lamb , supported by MAJ Gary Cooper, included members of our team in visits to Sierra Army Depot and...aspect of improving materiel stew - ardship is improving the quality of data related to the procurement, maintenance, and upgrading of equipment

  13. The first equipment for protection from nanoparticles

    International Nuclear Information System (INIS)

    Faure, Louis-Paul; Bombardier, Pierre; Reinwalt, Jean-Marie

    2009-01-01

    How can we guarantee the containment of ultrafine particles but also implement the ergonomic and handling constraints voiced by researchers? This is the equation that the engineers at FAURE INGENIERIE had to resolve to develop the first barrier protection equipment for nanoparticle research.

  14. Optimization of safety equipment outages improves safety

    International Nuclear Information System (INIS)

    Cepin, Marko

    2002-01-01

    Testing and maintenance activities of safety equipment in nuclear power plants are an important potential for risk and cost reduction. An optimization method is presented based on the simulated annealing algorithm. The method determines the optimal schedule of safety equipment outages due to testing and maintenance based on minimization of selected risk measure. The mean value of the selected time dependent risk measure represents the objective function of the optimization. The time dependent function of the selected risk measure is obtained from probabilistic safety assessment, i.e. the fault tree analysis at the system level and the fault tree/event tree analysis at the plant level, both extended with inclusion of time requirements. Results of several examples showed that it is possible to reduce risk by application of the proposed method. Because of large uncertainties in the probabilistic safety assessment, the most important result of the method may not be a selection of the most suitable schedule of safety equipment outages among those, which results in similarly low risk. But, it may be a prevention of such schedules of safety equipment outages, which result in high risk. Such finding increases the importance of evaluation speed versus the requirement of getting always the global optimum no matter if it is only slightly better that certain local one

  15. A range of equipment for dental radiography

    International Nuclear Information System (INIS)

    Bergman, G.P.M.; Clement, S.L.

    1980-01-01

    A brief review of the history of dental radiography is followed by a description of the latest Philips equipment, ranging from compact units for intra-oral radiography to advanced systems for panoramic techniques and skull radiography. The advantages of automatic exposure control and automatic film processing are also discussed. In conclusion, some probable future trends are forecast. (Auth.)

  16. 22 CFR 226.34 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... Relations AGENCY FOR INTERNATIONAL DEVELOPMENT ADMINISTRATION OF ASSISTANCE AWARDS TO U.S. NON-GOVERNMENTAL ORGANIZATIONS Post-award Requirements Property Standards § 226.34 Equipment. (a) Unless the agreement provides... to provide services to non-Federal outside organizations for a fee that is less than private...

  17. Spent fuel storage process equipment development

    International Nuclear Information System (INIS)

    Park, Hyun Soo; Lee, Jae Sol; Yoo, Jae Hyung

    1990-02-01

    Nuclear energy which is a major energy source of national energy supply entails spent fuels. Spent fuels which are high level radioactive meterials, are tricky to manage and need high technology. The objectives of this study are to establish and develop key elements of spent fuel management technologies: handling equipment and maintenance, process automation technology, colling system, and cleanup system. (author)

  18. 48 CFR 870.112 - Telecommunications equipment.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Telecommunications... DEPARTMENT SUPPLEMENTARY REGULATIONS SPECIAL PROCUREMENT CONTROLS Controls 870.112 Telecommunications... specifications for telecommunications equipment, as defined in VA manual MP-6, Part VIII (available at any VA...

  19. An Evaluation System for Foodservice Equipment

    Science.gov (United States)

    1985-10-01

    of the machine, as eggs , pancakes, etc. cannot be cooked oo a grooved surface. A grooved suriaca will be tilted towards tha grease trough for...Refrigerator Specialty Units PREPARATION EQUIPMENT Burger Forming Machine Electric Meatball Machine breading Machine Crepe Machine Breaded/Sifter

  20. Electronic detecting equipment in the Camac standard

    International Nuclear Information System (INIS)

    Basiladze, S.G.

    1981-01-01

    Basic tends of development of electron detecting equipment of modern facilities for experiments in nuclear physics are considered. Special attention is paid to developments of specialized hybrid integrated circuits, specialized processors for selection of events, usage of integrated circuits of memories in detecting units as well as to prospects of developing nuclear electronics standards [ru

  1. 78 FR 59623 - Emergency Medical Equipment

    Science.gov (United States)

    2013-09-27

    ... accordance with the FAA master minimum equipment list does not adversely affect aviation safety. This action... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Parts 121 and 135 [Docket No... inoperative Emergency Medical Kit (EMK) or automated external defibrillator (AED). A copy of Master Minimum...

  2. 7 CFR 3019.34 - Equipment.

    Science.gov (United States)

    2010-01-01

    ... EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Property Standards § 3019... accounting records shall be investigated to determine the causes of the difference. The recipient shall, in... requirement for the equipment exists in other Federal agencies. The Federal awarding agency shall issue...

  3. 24 CFR 84.34 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER... the physical inspection and those shown in the accounting records shall be investigated to determine... requirement for the equipment exists in other Federal agencies. HUD shall issue instructions to the recipient...

  4. A Guide for Equipping Industrial Arts Facilities.

    Science.gov (United States)

    American Industrial Arts Association, Washington, DC. Equipment Guide Committee.

    A guide for planning new and revising existing industrial arts facilities which gives a listing of tools and equipment recommended for each of the major areas of instruction (automotive and power mechanics, ceramics, drafting, electronics, elementary, general shop, graphic arts, metalworking, plastics, and woodworking). General descriptions and…

  5. Radiation protection calculations for diagnostic medical equipment

    International Nuclear Information System (INIS)

    Klueter, R.

    1992-01-01

    The standards DIN 6812 and DIN 6844 define the radiation protection requirements to be met by biomedical radiography equipment or systems for nuclear medicine. The paper explains the use of a specific computer program for radiation protection calculations. The program offers menu-controlled calculation, with free choice of the relevant nuclides. (DG) [de

  6. Equipment qualification testing - a practical approach

    International Nuclear Information System (INIS)

    Davies, G.A.; McDougall, R.I.; Poirier, M.P.

    1996-01-01

    When nuclear safety equipment is credited with a Required Safety Function it must properly perform that function to facilitate safe control and/or shutdown of the plant during a design basis accident. When such equipment is required to be environmentally (EQ) and/or seismically qualified (SQ) for safety related use in CANDU nuclear power plants, the preferred method of qualification is by type testing. The qualification testing process requires that the test specimen equipment be subjected to the aging stressors associated with the normal service conditions that it would experience during it's required qualified (or service) life. Following the aging process, the test specimen is in a condition representative of that in which it would be at the end of its service life in the plant. The test specimen is then subjected to a simulated accident during which it must satisfy performance requirements thereby demonstrating that it can perform its required safety function. The performance requirements specified for the qualification testing must be designed to ensure that satisfactory performance of the safety function is demonstrated during the qualification program. This paper provides descriptions of practical methods used in the deriving and satisfying of relevant performance requirements during the qualification testing of safety related equipment. (author)

  7. Magnet measuring equipment of SC2

    CERN Multimedia

    CERN PhotoLab

    1974-01-01

    Checking the positioning of the magnet measuring equipment installed between the poles of SC2. The steel structure in front of the magnet is designed to house the rotary condenser and to shield it from the stray magnetic field of the accelerator.

  8. Magnet measuring equipment of SC2

    CERN Multimedia

    1974-01-01

    Checking the positioning of the magnet measuring equipment installed between the poles of SC2. The steel structure in front of the magnet is designed to house the rotary condenser and to shield it from the stray magnetic field of the accelerator. On the left, Marinus van Gulik. (See Photo Archive 7402005 and Annual Report 1974, p. 44.)

  9. USING DIDACTIC EQUIPMENT IN VOCATIONAL SUBJECTS TEACHING

    OpenAIRE

    JIROUT, Jiří

    2011-01-01

    Baccalaureate Work ?Using Didactic Equipment In Vocational Subjects Teaching? describes various methods of teaching and using didactic engineering in education. Theoretic part describes general aspects of using didactic engineering, teaching methods a and ways how to use didactic engineering in teaching vocational subjects. Practical part finds how students appreciate using modern didactic aids and engineering in education.

  10. Robust control investigations for equipment loaded panels

    DEFF Research Database (Denmark)

    Aglietti, G.S.; Langley, R.S.; Rogers, E.

    1998-01-01

    This paper develops a modelling technique for equipment load panels which directly produces (adequate) models of the underlying dynamics on which to base robust controller design/evaluations. This technique is based on the use of the Lagrange's equations of motion and the resulting models...

  11. The first equipment for protection from nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Faure, Louis-Paul; Bombardier, Pierre; Reinwalt, Jean-Marie [FAURE INGENIERIE S.A., Parc Technologique des Fontaines, Chemin des Fontaines, F-38190 Bernin (France)], E-mail: laboratoire@faureingenierie.com

    2009-05-01

    How can we guarantee the containment of ultrafine particles but also implement the ergonomic and handling constraints voiced by researchers? This is the equation that the engineers at FAURE INGENIERIE had to resolve to develop the first barrier protection equipment for nanoparticle research.

  12. Longevity and Depreciation of Audiovisual Equipment.

    Science.gov (United States)

    Post, Richard

    1987-01-01

    Describes results of survey of media service directors at public universities in Ohio to determine the expected longevity of audiovisual equipment. Use of the Delphi technique for estimates is explained, results are compared with an earlier survey done in 1977, and use of spreadsheet software to calculate depreciation is discussed. (LRW)

  13. Design of experimental equipment at CRNL

    International Nuclear Information System (INIS)

    Godden, B.

    1976-01-01

    The Plant Design Division provides a design service to the research and development effort at CRNL. Severe constraints, both environmentally and spatially, are placed on the design of special equipment. Several examples are given. Finally, the use of automated drafting systems is described. (author)

  14. Mechanical equipment for magnet measurement and alignment

    International Nuclear Information System (INIS)

    Harvey, A.

    1992-05-01

    The mechanical equipment for measuring and aligning (or fiducializing) magnets is described by reference to devices designed and built by a number of laboratories. Some of these are now available commercially. The descriptions are supplemented by a list of representative sources of hardware

  15. Diagnosis of Equipment Failures by Pattern Recognition

    DEFF Research Database (Denmark)

    Pau, L. F.

    1974-01-01

    The main problems in relation to automatic fault finding and diagnosis in equipments or production systems are discussed: 1) compression of the syndrome and observation spaces for better discrimination between failure modes; 2) simultaneous display of the failure patterns and the failure instants...

  16. 36 CFR 1210.34 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... 1210.34 Parks, Forests, and Public Property NATIONAL ARCHIVES AND RECORDS ADMINISTRATION GENERAL RULES... data, including date of disposal and sales price or the method used to determine current fair market... the following standards. For equipment with a current per unit fair market value of $5,000 or more...

  17. Gamma scanning equipment for nuclear safeguards

    International Nuclear Information System (INIS)

    De Grandi, G.; Stanchi, L.

    1975-01-01

    Many reasons justify the use of gamma techniques in the field of nuclear safeguards. The paper describes electronic equipment for gamma-scanning of non-irradiated fuel elements. The control of the operation is completely digital and driven by a minicomputer and gives more accurate results in respect of an analog chain which has been successfully used in fuel element manufacturing plants

  18. Automated technological equipment-robot complexes

    International Nuclear Information System (INIS)

    Zhitomirskii, S.V.; Samorodskikh, B.L.

    1984-01-01

    This paper surveys the types of automated technological equipment robot complexes. The principal elements of such complexes are described. Complexes are divided into two principal groups: those using simultaneously acting robots, and those using successively acting robots. The great variety of types of robots using successive action is then described

  19. 14 CFR 125.355 - Airplane equipment.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplane equipment. 125.355 Section 125.355...: AIRPLANES HAVING A SEATING CAPACITY OF 20 OR MORE PASSENGERS OR A MAXIMUM PAYLOAD CAPACITY OF 6,000 POUNDS OR MORE; AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Flight Release Rules § 125.355 Airplane...

  20. 21 CFR 1020.32 - Fluoroscopic equipment.

    Science.gov (United States)

    2010-04-01

    ... manufacturer shall provide to users, under § 1020.30(h)(1)(i), precautions concerning the importance of remote... specified in § 1020.32(d)(1)(v). (iii) Equipment provided with both an AERC mode and a manual mode shall not... shall be operable only when continuous manual activation is provided by the operator. A continuous...