WorldWideScience

Sample records for epon su-8 resist

  1. Thermal and optical properties of sol-gel and SU-8 resists

    Science.gov (United States)

    Suzuki, Toshiyuki; Morikawa, Junko; Hashimoto, Toshimasa; Buividas, Ričardas; Gervinskas, Gediminas; Paipulas, Domas; Malinauskas, Mangirdas; Mizeikis, Vygantas; Juodkazis, Saulius

    2012-03-01

    We report on a combined differential scanning calorimetric (DSC) and Raman scattering study of thermal polymerization of sol-gel organic-inorganic SZ2080 and SU-8 resists. In SZ2080, endothermic peak at 95°C signify drying of the resist and justifies the required pre-bake at around 100°C for 1-2 h for the best performance during femtosecond (fs-)direct laser writing. A strong exothermic peak at 140°C (under 2 K/min heating rate) completes polymerization of the resist. It is revealed that 1wt% of photoinitiators change Raman scattering intensity of SZ2080 and can contribute efficiently to heating and cross-linking of photo-polymers. In the case of SU-8, a 65°C DSC feature related to solvent evaporation was observed. The strongest changes in Raman spectrum occurs at a narrow 895 cm-1 band which is linked to polymerization. Raman scattering taken during DSC revealed spectral changes following the polymerization; an applicability of this method for monitoring photopolymerization induced by ultra-fast laser sources and feasibility of a laser-modulated calorimetry is discussed.

  2. MICROSTRUCTURING OF SU-8 RESIST FOR MEMS AND BIO-APPLICATIONS

    OpenAIRE

    Dey, P.K.; Pramanick, B.; RaviShankar, A.; Ganguly, P.; Das, S.

    2017-01-01

    Some studies on the fabrication of micro-needles, micro-pillers, and micro-channels using SU-8 negative photoresist for MEMS and bio-applications are reported. The SU-8 processing technology was standardized for the purpose. Micro-pillars were fabricated on SU-8 polymer by soft lithographic technique. Micro-needles were realized on SU-8 film utilizing lensing effect of the etched groove structure of the glass substrate. Micro-channel was fabricated by molding of PDMS polymer on patterned SU-8...

  3. Focusing properties of x-ray polymer refractive lenses from SU-8 resist layer

    Science.gov (United States)

    Snigirev, Anatoly A.; Snigireva, Irina; Drakopoulos, Michael; Nazmov, Vladimir; Reznikova, Elena; Kuznetsov, Sergey; Grigoriev, Maxim; Mohr, Jurgen; Saile, Volker

    2003-12-01

    Compound refractive lenses printed in Al and Be are becoming the key X-ray focusing and imaging components of beamline optical layouts at the 3rd generation synchrotron radiation sources. Recently proposed planar optical elements based on Si, diamond etc. may substantially broaden the spectrum of the refractive optics applicability. Planar optics has focal distances ranging from millimeters to tens of meters offering nano- and micro-focusing lenses, as well as beam condensers and collimators. Here we promote deep X-ray lithography and LIGA-type techniques to create high aspect-ratio lens structures for different optical geometries. Planar X-ray refractive lenses were manufactured in 1 mm thick SU-8 negative resist layer by means of deep synchrotron radiation lithography. The focusing properties of lenses were studied at ID18F and BM5 beamlines at the ESRF using monochromatic radiation in the energy range of 10 - 25 keV. By optimizing lens layout, mask making and resist processing, lenses of good quality were fabricated. The resolution of about 270 nm (FWHM) with gain in the order of 300 was measured at 14 keV. In-line holography of B-fiber was realized in imaging and projection mode with a magnification of 3 and 20, respectively. Submicron features of the fiber were clearly resolved. A radiation stability test proved that the fabricated lenses don't change focusing characteristics after dose of absorbed X-ray radiation of about 2 MJ/cm3. The unique radiation stability along with the high effficiency of SU8 lenses opens wide range of their synchrotron radiation applications such as microfocusing elements, condensers and collimators.

  4. Mode-locked fiber laser using SU8 resist incorporating carbon nanotubes

    Science.gov (United States)

    Hernandez-Romano, Ivan; Mandridis, Dimitrios; May-Arrioja, Daniel A.; Sanchez-Mondragon, Jose J.; Delfyett, Peter J.

    2011-06-01

    We report the fabrication of a saturable absorber made of a novel polymer SU8 doped with Single Wall Carbon Nanotubes (SWCNTs). A passive mode-locked ring cavity fiber laser was built with a 100 μm thick SU8/SWCNT film inserted between two FC/APC connectors. Self-starting passively mode-locked lasing operation was observed at 1572.04 nm, with a FWHM of 3.26 nm. The autocorrelation trace was 1.536 ps corresponding to a pulse-width of 871 fs. The time-bandwidth product was 0.344, which is close enough to transform-limited sech squared pulses. The repetition rate was 21.27 MHz, and a maximum average output power of 1 mW was also measured.

  5. Single mode solid state distributed feedback dye laser fabricated by grey scale electron beam lithography on dye doped SU-8 resist

    DEFF Research Database (Denmark)

    Balslev, Søren; Rasmussen, Torben; Shi, Peixiong

    2005-01-01

    We demonstrate grey scale electron beam lithography on functionalized SU-8 resist for fabrication of single mode solid state dye laser devices. The resist is doped with Rhodamine 6G perchlorate and the lasers are based on a first order Bragg grating distributed feedback resonator. The lasers...

  6. Reconfigurable multiport EPON repeater

    Science.gov (United States)

    Oishi, Masayuki; Inohara, Ryo; Agata, Akira; Horiuchi, Yukio

    2009-11-01

    An extended reach EPON repeater is one of the solutions to effectively expand FTTH service areas. In this paper, we propose a reconfigurable multi-port EPON repeater for effective accommodation of multiple ODNs with a single OLT line card. The proposed repeater, which has multi-ports in both OLT and ODN sides, consists of TRs, BTRs with the CDR function and a reconfigurable electrical matrix switch, can accommodate multiple ODNs to a single OLT line card by controlling the connection of the matrix switch. Although conventional EPON repeaters require full OLT line cards to accommodate subscribers from the initial installation stage, the proposed repeater can dramatically reduce the number of required line cards especially when the number of subscribers is less than a half of the maximum registerable users per OLT. Numerical calculation results show that the extended reach EPON system with the proposed EPON repeater can save 17.5% of the initial installation cost compared with a conventional repeater, and can be less expensive than conventional systems up to the maximum subscribers especially when the percentage of ODNs in lightly-populated areas is higher.

  7. Processing of thin SU-8 films

    International Nuclear Information System (INIS)

    Keller, Stephan; Blagoi, Gabriela; Lillemose, Michael; Haefliger, Daniel; Boisen, Anja

    2008-01-01

    This paper summarizes the results of the process optimization for SU-8 films with thicknesses ≤5 µm. The influence of soft-bake conditions, exposure dose and post-exposure-bake parameters on residual film stress, structural stability and lithographic resolution was investigated. Conventionally, the SU-8 is soft-baked after spin coating to remove the solvent. After the exposure, a post-exposure bake at a high temperature T PEB ≥ 90 °C is required to cross-link the resist. However, for thin SU-8 films this often results in cracking or delamination due to residual film stress. The approach of the process optimization is to keep a considerable amount of the solvent in the SU-8 before exposure to facilitate photo-acid diffusion and to increase the mobility of the monomers. The experiments demonstrate that a replacement of the soft-bake by a short solvent evaporation time at ambient temperature allows cross-linking of the thin SU-8 films even at a low T PEB = 50 °C. Fourier-transform infrared spectroscopy is used to confirm the increased cross-linking density. The low thermal stress due to the reduced T PEB and the improved structural stability result in crack-free structures and solve the issue of delamination. The knowledge of the influence of different processing parameters on the responses allows the design of optimized processes for thin SU-8 films depending on the specific application

  8. Bi cluster-assembled interconnects produced using SU8 templates

    International Nuclear Information System (INIS)

    Partridge, J G; Matthewson, T; Brown, S A

    2007-01-01

    Bi clusters with an average diameter of 25 nm have been deposited from an inert gas aggregation source and assembled into thin-film interconnects which are formed between planar electrical contacts and supported on Si substrates passivated with Si 3 N 4 or thermally grown oxide. A layer of SU8 (a negative photoresist based on EPON SU-8 epoxy resin) is patterned using optical or electron-beam lithography, and it defines the position and dimensions of the cluster film. The conduction between the contacts is monitored throughout the deposition/assembly process, and subsequent I(V) characterization is performed in situ. Bi cluster-assembled interconnects have been fabricated with nanoscale widths and with up to 1:1 thickness:width aspect ratios. The conductivity of these interconnects has been increased, post-deposition, using a simple thermal annealing process

  9. Chemical synthesis on SU-8

    DEFF Research Database (Denmark)

    Qvortrup, Katrine; Taveras, Kennedy; Thastrup, Ole

    2011-01-01

    In this paper we describe a highly effective surface modification of SU-8 microparticles, the attachment of appropriate linkers for solid-supported synthesis, and the successful chemical modification of these particles via controlled multi-step organic synthesis leading to molecules attached...

  10. SU-8 cantilever chip interconnection

    DEFF Research Database (Denmark)

    Johansson, Alicia Charlotte; Janting, Jakob; Schultz, Peter

    2006-01-01

    The polymer SU-8 is becoming widely used for all kinds of micromechanical and microfluidic devices, not only as a photoresist but also as the constitutional material of the devices. Many of these polymeric devices need to include a microfluidic system as well as electrical connection from the ele...

  11. Micromechanical testing of SU-8 cantilevers

    OpenAIRE

    Hopcroft, M; Kramer, T; Kim, G; Takashima, K; Higo, Y; Moore, D; Brugger, J

    2005-01-01

    SU-8 is a photoplastic polymer with a wide range of possible applications in microtechnology. Cantilevers designed for atomic force microscopes were fabricated in SU-8. The mechanical properties of these cantilevers were investigated using two microscale testing techniques: contact surface profilometer beam deflection and static load deflection at a point on the beam using a specially designed test machine. The SU-8 Young's modulus value from the microscale test methods is approximately 2-3 GPa.

  12. SU-8 negative photoresist for optical mask manufacturing

    Science.gov (United States)

    Bogdanov, Alexei L.

    2000-06-01

    The requirements for better control, linearity, and uniformity of critical dimension (CD) on photomasks in fabrication of 180 and 150 nm generation devices result in increasing demand for thinner, more etching durable, and more sensitive e-beam resists. Novolac based resists with chemical amplification have been a choice for their sensitivity and stability during etching. However, difficult CD control due to the acid catalyzer diffusion and quite narrow post exposure bake (PEB) process window are some of the major drawbacks of these resists. SU-8 is recently introduced to the market negative photoresist. High sensitivity, fairly good adhesion properties, and relatively simple processing of SU-8 make it a good substitution for novolac based chemically amplified negative e-beam resists in optical mask manufacturing. The replacement of traditional chemically amplified resists by SU- 8 can increase the process latitude and reduce resist costs. Among the obvious drawbacks of SU-8 are the use of solvent- based developer and demand of oxygen plasma for resist removal. In this paper the use of SU-8 for optical mask manufacturing is reported. All steps of resist film preparation, exposure and development are paid a share of attention. Possibilities to use reactive ion etching (RIE) with oxygen in order to increase resist mask contrast are discussed. Special exposure strategy (pattern outlining) was employed to further improve the edge definition. The resist PEB temperature and time were studied to estimate their weight in overall CD control performance. Specially designed test patterns with 0.25 micrometer design rule could be firmly transferred into a chromium layer both by wet etching and ion milling. Influence of exposure dose variation on the pattern CD change was studied.

  13. SU-8 Based Piezoresistive Mechanical Sensor

    DEFF Research Database (Denmark)

    Thaysen, Jacob; Yalcinkaya, Arda Deniz; Vestergaard, R.K.

    2002-01-01

    We present the first SU-8 based piezoresistive mechanical sensor. Conventionally, silicon has been used as a piezoresistive material due to its high gauge factor and thereby high sensitivity to strain changes in a sensor. By using the fact that SU-8 is much softer than silicon and that a gold...

  14. Novel SU-8 based vacuum wafer-level packaging for MEMS devices

    DEFF Research Database (Denmark)

    Murillo, Gonzalo; Davis, Zachary James; Keller, Stephan Urs

    2010-01-01

    This work presents a simple and low-cost SU-8 based wafer-level vacuum packaging method which is CMOS and MEMS compatible. Different approaches have been investigated by taking advantage of the properties of SU-8, such as chemical resistance, optical transparence, mechanical reliability and versa......This work presents a simple and low-cost SU-8 based wafer-level vacuum packaging method which is CMOS and MEMS compatible. Different approaches have been investigated by taking advantage of the properties of SU-8, such as chemical resistance, optical transparence, mechanical reliability...

  15. Diffusion of water into SU-8 microcantilevers

    DEFF Research Database (Denmark)

    Liu, C.J.; Liu, Y.; Sokuler, M.

    2010-01-01

    We present a method to monitor the diffusion of liquid molecules in polymers. A microdrop of water is deposited by a piezoelectric drop generator onto the upper surface of a cantilever made of SU-8 based photoresist. In response, the cantilever bends in the opposite direction. We find...... sophisticated finite element model the diffusion coefficient of water in the SU-8 polymer can be determined quantitatively from the dynamics of cantilever bending....... that this bending is mainly caused by the diffusion of water into the cantilever and the consequent swelling of SU-8. Using a one-dimensional diffusion model and assuming a simple swelling law, we qualitatively model the bending of the cantilever during in and out diffusion of water in SU-8. With a more...

  16. On SU(8)sub(L)xSU(8)sub(R) grand unified model

    International Nuclear Information System (INIS)

    Pirogov, Yu.F.

    1981-01-01

    A set of general propositions is considered which ground the choice of the SU(8)sub(L)xSU(8)sub(R) group as a unified symmetry group. According to these propositions the group SU(8)sub(L)xSU(8)sub(R) is the most natural unified group, it is the maximal symmetry group of the kinetic term of the lagrangian single family which conserves the fermion number. A new principle is introduced. According to this principle, the mirror doubling of the fermion spectrum, necessary for renormalizability of the given unified model is, on the other hand, a manifestation of the extended conformal invariance at short distances [ru

  17. SU-8 doped and encapsulated n-type graphene nanomesh with high air stability

    Energy Technology Data Exchange (ETDEWEB)

    Al-Mumen, Haider [Department of Electrical and Computer Engineering, Michigan State University, East Lansing, Michigan 48824 (United States); Department of Electrical Engineering, University of Babylon, Babylon (Iraq); Dong, Lixin; Li, Wen, E-mail: wenli@egr.msu.edu [Department of Electrical and Computer Engineering, Michigan State University, East Lansing, Michigan 48824 (United States)

    2013-12-02

    N-type doping of graphene with long-term chemical stability in air represents a significant challenge for practical application of graphene electronics. This paper reports a reversible doping method to achieve highly stable n-type graphene nanomeshes, in which the SU-8 photoresist simultaneously serves as an effective electron dopant and an excellent encapsulating layer. The chemically stable n-type characteristics of the SU-8 doped graphene were evaluated in air using their Raman spectra, electrical transport properties, and electronic band structures. The SU-8 doping does minimum damage to the hexagonal carbon lattice of graphene and is completely reversible by removing the uncrosslinked SU-8 resist.

  18. SU-8 micro Coriolis mass flow sensor

    NARCIS (Netherlands)

    Monge, Rosa; Groenesteijn, Jarno; Alveringh, Dennis; Wiegerink, Remco J.; Lötters, Joost Conrad; Fernandez, Luis J.

    2017-01-01

    Abstract This work presents the modelling, design, fabrication and test of the first micro Coriolis mass flow sensor fully fabricated in SU-8 by photolithography processes. The sensor consists of a channel with rectangular cross-section with inner opening of 100 μm × 100 μm and is actuated at

  19. Enhanced Sleep Mode MAC Control for EPON

    DEFF Research Database (Denmark)

    Yan, Ying; Dittmann, Lars

    2011-01-01

    This paper introduces sleep mode operations for EPON. New MAC control functions are proposed to schedule sleep periods. Traffic profiles are considered to optimize energy efficiency and network performances. Simulation results are analyzed in OPNET modeler.......This paper introduces sleep mode operations for EPON. New MAC control functions are proposed to schedule sleep periods. Traffic profiles are considered to optimize energy efficiency and network performances. Simulation results are analyzed in OPNET modeler....

  20. Surface modification of SU8 photoresist for shrinkage improvement in a monolithic MEMS microstructure

    Science.gov (United States)

    Chung, C. K.; Hong, Y. Z.

    2007-02-01

    The effect of O2 plasma treatment on the surface property of exposed and unexposed SU8 photoresist has been investigated for the fabrication of a monolithic MEMS microstructure. It can solve the non-uniformity problem of second resist coating on the SU8 with high intrinsic shrinkage after exposure and post-exposure baking (PEB) in the fabrication of the stacked polymer-metal or polymer-polymer structure, which was used in the application of microfluid, bio and chemistry. The thickness difference of untreated SU8 before PEB between the exposed and unexposed SU8 was about 0.3% while that after PEB increased to about 6%. It could result in large non-uniformity of about 18 µm thickness difference for the following second resist coating on the hydrophobic surface without plasma treatment. The surface property of SU8 in terms of the contact angle and surface energy can be adjusted by O2 plasma treatment for enhancing the coating uniformity of the following resist. The measured contact angles of the exposed and unexposed SU8 decrease with O2 plasma time, corresponding to the increased surface energy determined by the Lifshitz-van der Waals/Lewis acid-base approach. It displayed that the similar hydrophilic surface property can minimize the thickness difference of second resist coating on the first shrunken SU8. A monolithic nozzle plate with a physical resolution of 600 dpi in a single column was demonstrated for an inkjet application based on the improved uniformity.

  1. In situ SU-8 silver nanocomposites

    Directory of Open Access Journals (Sweden)

    Søren V. Fischer

    2015-07-01

    Full Text Available Nanocomposite materials containing metal nanoparticles are of considerable interest in photonics and optoelectronics applications. However, device fabrication of such materials always encounters the challenge of incorporation of preformed nanoparticles into photoresist materials. As a solution to this problem, an easy new method of fabricating silver nanocomposites by an in situ reduction of precursors within the epoxy-based photoresist SU-8 has been developed. AgNO3 dissolved in acetonitrile and mixed with the epoxy-based photoresist SU-8 forms silver nanoparticles primarily during the pre- and post-exposure soft bake steps at 95 °C. A further high-temperature treatment at 300 °C resulted in the formation of densely homogeneously distributed silver nanoparticles in the photoresist matrix. No particle growth or agglomeration of nanoparticles is observed at this point. The reported new in situ silver nanocomposite materials can be spin coated as homogeneous thin films and structured by using UV lithography. A resolution of 5 µm is achieved in the lithographic process. The UV exposure time is found to be independent of the nanoparticle concentration. The fabricated silver nanocomposites exhibit high plasmonic responses suitable for the development of new optoelectronic and optical sensing devices.

  2. High temperature SU-8 pyrolysis for fabrication of carbon electrodes

    DEFF Research Database (Denmark)

    Hassan, Yasmin Mohamed; Caviglia, Claudia; Hemanth, Suhith

    2017-01-01

    In this work, we present the investigation of the pyrolysis parameters at high temperature (1100 °C) for the fabrication of two-dimensional pyrolytic carbon electrodes. The electrodes were fabricated by pyrolysis of lithographically patterned negative epoxy based photoresist SU-8. A central...... composite experimental design was used to identify the influence of dwell time at the highest pyrolysis temperature and heating rate on electrical, electrochemical and structural properties of the pyrolytic carbon: Van der Pauw sheet resistance measurements, cyclic voltammetry, electrochemical impedance...... spectroscopy and Raman spectroscopy were used to characterize the pyrolytic carbon. The results show that the temperature increase from 900 °C to 1100 °C improves the electrical and electrochemical properties. At 1100 °C, longer dwell time leads to lower resistivity, while the variation of the pyrolysis...

  3. On grand unified SU(8)sub(L) x SU(8)sub(R) model

    International Nuclear Information System (INIS)

    Pirogov, Yu.F.

    1980-01-01

    In the model of early chiral grand unification SU(8)sub(L)xSU(8)sub(R) with intermediate symmetry hierarchies the radiation corrections for sinsup(2)thetasub(W)(μ) and α(μ) are calculated and unification mass M 8 is found in the one loop approximation with Higgs fields contribution being neglected. It is shown that there exists a natural hierarchy, leading to the decrease of sinsup(2)thetasub(W)(Msub(W)) down to the value sinsup(2)thetasub(W)=1/5-1/4 and simultaneous decrease of M 8 down to M 8 =(10 6 -10 7 ) GeV as compared with the values when there is no hierarchy [ru

  4. SU-8 photoresist and SU-8 based nanocomposites for broadband acoustical matching at 1 GHz

    Energy Technology Data Exchange (ETDEWEB)

    Ndieguene, A; Campistron, P; Carlier, J; Wang, S; Callens-Debavelaere, D; Nongaillard, B, E-mail: Assane.Ndieguene@meletu.univ-valenciennes.f [Univ Lille Nord de France, F-59000 Lille (France)

    2009-11-01

    So as to integrate acoustic functions in BioMEMS using 1 GHz ZnO transducers deposited on silicon substrates, acoustic waves propagation through the silicon substrate and its transmission in water needs to be maximized (the insertion losses at the Si / water interface are about 6dB). In the context of integration, it is interesting for mechanical impedance matching to use photosensitive materials such as SU-8 so that patterns may be obtained. Nanocomposite materials based on SU-8 mixed with nanoparticles having adequate impedances were fabricated. These new materials are characterized in terms of their acoustic velocity, impedance and attenuation. For this, the nanocomposite layers are deposited on the substrate by spin coating to obtain a thickness of about 10 {mu}m, in order to separate acoustic echoes from the material (even if {lambda}/4 layer thickness is lower than 1 {mu}m). The insertion losses of the device immersed in water can be simulated as a function of frequency for a given reflection coefficient between the silicon substrate and the photoresist. The characteristics of some nanocomposites made with SU-8 and various concentrations of nanoparticles like Ti0{sub 2}, SrTiO{sub 3} or W have been determined.

  5. ONU Power Saving Scheme for EPON System

    Science.gov (United States)

    Mukai, Hiroaki; Tano, Fumihiko; Tanaka, Masaki; Kozaki, Seiji; Yamanaka, Hideaki

    PON (Passive Optical Network) achieves FTTH (Fiber To The Home) economically, by sharing an optical fiber among plural subscribers. Recently, global climate change has been recognized as a serious near term problem. Power saving techniques for electronic devices are important. In PON system, the ONU (Optical Network Unit) power saving scheme has been studied and defined in XG-PON. In this paper, we propose an ONU power saving scheme for EPON. Then, we present an analysis of the power reduction effect and the data transmission delay caused by the ONU power saving scheme. According to the analysis, we propose an efficient provisioning method for the ONU power saving scheme which is applicable to both of XG-PON and EPON.

  6. L’idéologie dans les chants de l’EPON

    Directory of Open Access Journals (Sweden)

    Joëlle Dalègre

    2011-11-01

    Full Text Available L’idéologie de l’EPON, (organisation de jeunesse de la résistance grecque vue à travers ses chants, l’une de ses armes favorites de propagande.Cette communication se propose, à travers quelques chants, de montrer les grandes thèmes idéologiques de l’EPON, tout en la replaçant dans le cadre spécifique grec. Créée par le mouvement de résistance de masse du pays, l’EAM, l’EPON se propose d’encadrer les jeunes de tous âges, de les faire participer à la résistance, civile et parfois armée et de les conduire vers la construction de l’avenir radieux qui leur est promis à la fin de la guerre. Le chant fait partie des nombreux moyens de propagande utilisés par l’EPON (et précédemment par l’EON mais aussi d’un réel travail d’éducation entrepris en tous lieux par les cadres de l’organisation, souvent des enseignants. Justice, travail, école, prospérité, égalité homme/femme, des réalités inconnues dans la Grèce de l’avant-guerre qui ne peuvent que provoquer enthousiasme et espérance dans une génération prête à se sacrifier généreusement.Based on a number of songs, this communication summarizes the great ideological themes of EPON, while at the same time placing them in the specifically Greek context. Created by EAM, the national resistance movement, EPON set out to recruit the young of all ages, to make them participate in the civil and armed resistance against the occupiers, and to help them build the brilliant future they were promised at the end of the war. Song was one of the many forms of propaganda used by EPON, but also a real form of education undertaken everywhere by the heads of the organisation, who were often teachers. Justice, work, school, prosperity, equality between men and women, unknown realities in pre-war Greece that could only inspire enthusiasm and hope in a generation prepared to make any sacrifice.

  7. Broken SU(8) symmetry and the new particles

    International Nuclear Information System (INIS)

    Kramer, G.; Schiller, D.H.

    1976-05-01

    We study the mass spectra and wave functions for vector and pseudoscalar mesons in broken SU(8) (SU(8) is contained in SU(4)F * SU(2)J), where F stands for flavour and J for usual spin. The connection with the standard mass breaking in SU(4)F is worked out. We find that even in the presence of strong SU(8) breaking the ideal mixing scheme for the vector mesons can be approximately retained. For the pseudoscalar mesons the mixing of the singlet with the 63-plet representation of SU(8) turns out to be essential and stongly nonideal. (orig.) [de

  8. Photochemical modification and patterning of SU-8 using Anthraquinone photolinkers

    DEFF Research Database (Denmark)

    Blagoi, Gabriela; Keller, Stephan Urs; Persson, Karl Fredrik

    2008-01-01

    -dimensional patterns on a Novolac A derivative polymer (SU-8) and, subsequently, their functionalization with biomolecules. Anthraquinone (AQ) derivatives are used to chemically modify and pattern SU-8 surfaces. Features as small as 20 μm are obtained when using uncollimated light. The X−Y spatial resolution...

  9. Low Cost SU8 Based Above IC Process for High Q RF Power Inductors Integration

    International Nuclear Information System (INIS)

    Ghannam, A.; Bourrier, D.; Viallon, Ch.; Parra, Th.

    2011-01-01

    This paper presents a new process for integration of high-Q RF power inductors above low resistivity silicon substrates. The process uses the SU8 resin as a dielectric layer. The aim of using the SU8 is to form thick dielectric layer that can enhance the performance of the inductors. The flexibility of the process enables the possibility to realize complex shaped planar inductors with various dielectric and metal thicknesses to meet the requirements of the application. Q values of 55 at 5 GHz has been demonstrated for an inductance value of 0.8 nH using a 60 μm thick SU8 layer and 30 μm thick copper ribbons. (author)

  10. Fabrication of raised and inverted SU8 polymer waveguides

    Science.gov (United States)

    Holland, Anthony S.; Mitchell, Arnan; Balkunje, Vishal S.; Austin, Mike W.; Raghunathan, Mukund K.

    2005-01-01

    Polymer films with high optical transmission have been investigated for making optical devices for several years. SU8 photoresist and optical adhesives have been investigated for use as thin films for optical devices, not what they were originally designed for. Optical adhesives are typically a one component thermoset polymer and are convenient to use for making thin film optical devices such as waveguides. They are prepared in minutes as thin films unlike SU8, which has to be carefully thermally cured over several hours for optimum results. However SU8 can be accurately patterned to form the geometry of structures required for single mode optical waveguides. SU8 in combination with the lower refractive index optical adhesive films such as UV15 from Master Bond are used to form single and multi mode waveguides. SU8 is photopatternable but we have also used dry etching of the SU8 layer or the other polymer layers e.g. UV15 to form the ribs, ridges or trenches required to guide single modes of light. Optical waveguides were also fabricated using only optical adhesives of different refractive indices. The resolution obtainable is poorer than with SU8 and hence multi mode waveguides are obtained. Loss measurements have been obtained for waveguides of different geometries and material combinations. The process for making polymer waveguides is demonstrated for making large multi mode waveguides and microfluidic channels by scaling the process up in size.

  11. Functionalized SU-8 patterned with X-ray Lithography

    DEFF Research Database (Denmark)

    Balslev, Søren; Romanato, F.

    2005-01-01

    spontaneous emission light source that couples out light normal to the chip plane. In addition we examine the influence of the x-ray irradiation on the fluorescence of thin films of dye doped SU-8. The dye embedded in the SU-8 is optically excited during, characterization by an external light source tuned......In this work we demonstrate the feasibility of x-ray lithography on SU-8 photoresist doped with the laser dye Rhodamine 6G, while retaining the photoactive properties of the embedded dye. Two kinds of structures are fabricated via soft x-ray lithography and characterized: a laser and in amplified...

  12. Using IGMP V3 for controllable multicast over EPON

    Science.gov (United States)

    Zhang, Chuanhao; Liu, Deming; Zhang, Li; Wu, Guangsheng

    2008-11-01

    The character of 1Gbps bandwidth and tree-based structure make EPON very suitable for broadcast or multicast services such as IPTV. The document proposed a novel scheme, based on the former research for controllable multicast over EPON system, mainly considering system security and maintainability. It can both control the IPTV program source's and the receiver's validity, improving the efficiency and precision. The processing of the two configurations mode is given in detail.

  13. Innovative SU-8 Lithography Techniques and Their Applications

    Directory of Open Access Journals (Sweden)

    Jeong Bong Lee

    2014-12-01

    Full Text Available SU-8 has been widely used in a variety of applications for creating structures in micro-scale as well as sub-micron scales for more than 15 years. One of the most common structures made of SU-8 is tall (up to millimeters high-aspect-ratio (up to 100:1 3D microstructure, which is far better than that made of any other photoresists. There has been a great deal of efforts in developing innovative unconventional lithography techniques to fully utilize the thick high aspect ratio nature of the SU-8 photoresist. Those unconventional lithography techniques include inclined ultraviolet (UV exposure, back-side UV exposure, drawing lithography, and moving-mask UV lithography. In addition, since SU-8 is a negative-tone photoresist, it has been a popular choice of material for multiple-photon interference lithography for the periodic structure in scales down to deep sub-microns such as photonic crystals. These innovative lithography techniques for SU-8 have led to a lot of unprecedented capabilities for creating unique micro- and nano-structures. This paper reviews such innovative lithography techniques developed in the past 15 years or so.

  14. Using an SU-8 Photoresist Structure and Cytochrome C Thin Film Sensing Material for a Microbolometer

    Directory of Open Access Journals (Sweden)

    Guo-Dung John Su

    2012-11-01

    Full Text Available There are two critical parameters for microbolometers: the temperature coefficient of resistance (TCR of the sensing material, and the thermal conductance of the insulation structure. Cytochrome c protein, having a high TCR, is a good candidate for infrared detection. We can use SU-8 photoresist for the thermal insulation structure, given its low thermal conductance. In this study, we designed a platform structure based on a SU-8 photoresist. We fabricated an infrared sensing pixel and recorded a high TCR for this new structure. The SU-8 photoresist insulation structure was fabricated using the exposure dose method. We experimentally demonstrated high values of TCR from 22%/K to 25.7%/K, and the measured noise was 1.2 × 10–8 V2/Hz at 60 Hz. When the bias current was 2 μA, the calculated voltage responsivity was 1.16 × 105 V/W. This study presents a new kind of microbolometer based on cytochrome c protein on top of an SU-8 photoresist platform that does not require expensive vacuum deposition equipment.

  15. Investigation of the bond strength between the photo-sensitive polymer SU-8 and gold

    DEFF Research Database (Denmark)

    Nordström, Maria; Johansson, Alicia; Sánchez Noguerón, E.

    2005-01-01

    adhesion promotors between the SU-8 and Au; (ii) the influence of the processing sequence, keeping either Au or SU-8 as the bottom layer; (iii) the importance of the UV exposure dosage of the SU-8. For comparison, also the bond strength between SU-8 and other materials was measured. For SU-8 and Au without...

  16. Development of untethered SU-8 polymer scratch drive microrobots

    KAUST Repository

    Valencia Garcia, Manuel

    2011-01-01

    This paper presents the design, simulation, fabrication and testing of novel, untethered SU-8 polymer microrobots based on scratch drive actuators (SDAs). The design consists of two 100×120×10μm linked SDAs, individually operated close to their resonant frequencies. The resonant frequency and deflection behavior of an individual SDA can be controlled by its shape, thickness, and stiffening design features. As a result, paired SDAs can be actuated individually or simultaneously by a multifrequency driving signal, allowing for two-dimensional displacement. The fabrication process uses SU-8 as structural material and PMGI as sacrificial material. The SU-8 provides a flexible material for the SDA\\'s plates as well as the bushing. Finally, a Cr/Au layer is blanket deposited to provide electrical conductivity.

  17. Development of untethered SU-8 polymer scratch drive microrobots

    KAUST Repository

    Valencia Garcia, Manuel; Atallah, Tarek Nabil; Castro, David; Conchouso Gonzalez, David; Al Dosari, Mishari Ibraheem; Hammad, Rafat; Al Rawashdeh, Ehab Jamal; Zaher, Amir Omar; Kosel, Jü rgen; Foulds, Ian G.

    2011-01-01

    This paper presents the design, simulation, fabrication and testing of novel, untethered SU-8 polymer microrobots based on scratch drive actuators (SDAs). The design consists of two 100×120×10μm linked SDAs, individually operated close to their resonant frequencies. The resonant frequency and deflection behavior of an individual SDA can be controlled by its shape, thickness, and stiffening design features. As a result, paired SDAs can be actuated individually or simultaneously by a multifrequency driving signal, allowing for two-dimensional displacement. The fabrication process uses SU-8 as structural material and PMGI as sacrificial material. The SU-8 provides a flexible material for the SDA's plates as well as the bushing. Finally, a Cr/Au layer is blanket deposited to provide electrical conductivity.

  18. Fabricating microfluidic valve master molds in SU-8 photoresist

    Science.gov (United States)

    Dy, Aaron J.; Cosmanescu, Alin; Sluka, James; Glazier, James A.; Stupack, Dwayne; Amarie, Dragos

    2014-05-01

    Multilayer soft lithography has become a powerful tool in analytical chemistry, biochemistry, material and life sciences, and medical research. Complex fluidic micro-circuits require reliable components that integrate easily into microchips. We introduce two novel approaches to master mold fabrication for constructing in-line micro-valves using SU-8. Our fabrication techniques enable robust and versatile integration of many lab-on-a-chip functions including filters, mixers, pumps, stream focusing and cell-culture chambers, with in-line valves. SU-8 created more robust valve master molds than the conventional positive photoresists used in multilayer soft lithography, but maintained the advantages of biocompatibility and rapid prototyping. As an example, we used valve master molds made of SU-8 to fabricate PDMS chips capable of precisely controlling beads or cells in solution.

  19. SU-8 as a Material for Microfabricated Particle Physics Detectors

    CERN Document Server

    Maoddi, Pietro; Jiguet, Sebastien; Renaud, Philippe

    2014-01-01

    Several recent detector te chnologies developed for particle physics applications are based on microfabricated structures. Dete ctors built with this approach generally exhibit the overall best performance in te rms of spatial and time resolution. Many properties of the SU-8 photoepoxy make it suitable for the manufacturing of microstructured particle detectors. This arti cle aims to review some emerging detector technologies making use of SU-8 microstructu ring, namely micropatte rn gaseous detectors and microfluidic scintillation detectors. Th e general working principle and main process steps for the fabrication of each device are reported, with a focus on the advantages brought to the device functionality by the us e of SU-8. A novel process based on multiple bonding steps for the fabrication of thin multila yer microfluidic scin tillation detectors developed by the authors is presented. Finally, a brief overview of the applications for the discussed devices is given.

  20. Fabricating microfluidic valve master molds in SU-8 photoresist

    International Nuclear Information System (INIS)

    Dy, Aaron J; Cosmanescu, Alin; Sluka, James; Glazier, James A; Amarie, Dragos; Stupack, Dwayne

    2014-01-01

    Multilayer soft lithography has become a powerful tool in analytical chemistry, biochemistry, material and life sciences, and medical research. Complex fluidic micro-circuits require reliable components that integrate easily into microchips. We introduce two novel approaches to master mold fabrication for constructing in-line micro-valves using SU-8. Our fabrication techniques enable robust and versatile integration of many lab-on-a-chip functions including filters, mixers, pumps, stream focusing and cell-culture chambers, with in-line valves. SU-8 created more robust valve master molds than the conventional positive photoresists used in multilayer soft lithography, but maintained the advantages of biocompatibility and rapid prototyping. As an example, we used valve master molds made of SU-8 to fabricate PDMS chips capable of precisely controlling beads or cells in solution. (technical note)

  1. Effects of design geometry on SU8 polymer waveguides

    Science.gov (United States)

    Holland, Anthony S.; Balkunje, Vishal S.; Mitchell, Arnan; Austin, Michael W.; Raghunathan, Mukund K.; Kostovski, Gorgi

    2005-02-01

    The spin-on photoresist SU8 from MicroChem has a relatively high refractive index (n=1.57 at 1550nm) compared with other polymers. It is stable and has high optical transmission at optical communication wavelengths. In this paper we study rib waveguides fabricated using SU8 as the core layer and thermoset polymers UV15 (n=1.50 at 1550nm) from Master Bond and NOA61 (n=1.54 at 1550nm) from Gentec as the cladding layers. The rib height is varied from 0.3 to 1.7μm high. This is part of the SU8 layer sandwiched between the cladding layers. The waveguides are tested to determine the effects of varying this geometry for single mode optical transmission. The lengths of the waveguides were 1.5 cm to 5 cm.

  2. SU-8 Photolithography as a Toolbox for Carbon MEMS

    Directory of Open Access Journals (Sweden)

    Rodrigo Martinez-Duarte

    2014-09-01

    Full Text Available The use of SU-8 as precursor for glass-like carbon, or glassy carbon, is presented here. SU-8 carbonizes when subject to high temperature under inert atmosphere. Although epoxy-based precursors can be patterned in a variety of ways, photolithography is chosen due to its resolution and reproducibility. Here, a number of improvements to traditional photolithography are introduced to increase the versatility of the process. The shrinkage of SU-8 during carbonization is then detailed as one of the guidelines necessary to design carbon patterns. A couple of applications—(1 carbon-electrode dielectrophoresis for bioparticle manipulation; and (2 the use of carbon structures as micro-molds are also presented.

  3. SU-8 micropatterning for microfluidic droplet and microparticle focusing

    International Nuclear Information System (INIS)

    Debuisson, Damien; Senez, Vincent; Arscott, Steve

    2011-01-01

    We demonstrate micropatterned surfaces consisting of concentric circles and spirals which can focus an evaporating sessile droplet to a specific location on a surface. We also study the micropattern geometry to focus microparticles contained within the droplet. The micropatterned surfaces are fabricated using the photoresist SU-8. Our process enables the modification of the surface wetting via the formation of smooth trench-like defects in the SU-8 which define the micropatterns; the geometry of these micropatterns determines the droplet/microparticle focusing. It is clearly shown that the introduction of small gaps into the micropatterns promotes microparticle centring due to the modification of the depinning angle of the droplet. We also show that the use of spiral micropatterns promotes microparticle centring. Finally, microparticle focusing can be enhanced by modification of surface wetting via the addition of a thin fluorocarbon hydrophobic layer onto the SU-8

  4. Improved anti-stiction coating of SU-8 molds

    DEFF Research Database (Denmark)

    Lange, Jacob Moresco; Clausen, Casper Hyttel; Svendsen, Winnie Edith

    2010-01-01

    of the epoxy groups by oxygen plasma or sulfuric acid improves the deposition of FDTS. The deposition of FDTS on acid-activated and untreated SU-8 gave an identical well performing anti-stiction coating, as opposed to oxygen plasma activated surface which resulted in a poor FDTS coverage. In this paper...

  5. SU-8 photoresist-derived electrospun carbon nanofibres as high ...

    Indian Academy of Sciences (India)

    ... Refresher Courses · Symposia · Live Streaming. Home; Journals; Bulletin of Materials Science; Volume 40; Issue 3. SU-8 photoresist-derived electrospun carbon nanofibres as high-capacity anode material for lithium ion battery. M KAKUNURI S KAUSHIK A SAINI C S SHARMA. Volume 40 Issue 3 June 2017 pp 435-439 ...

  6. Combined electron beam and UV lithography in SU-8

    DEFF Research Database (Denmark)

    Gersborg-Hansen, Morten; Thamdrup, Lasse Højlund; Mironov, Andrej

    2007-01-01

    We present combined electron beam and UV lithography (CEUL) in SU-8 as a fast and flexible lithographic technique for prototyping of functional polymer devices and pattern transfer applications. CEUL is a lithographic technique suitable for defining both micrometer and nanometer scale features...

  7. Special Issue: 15 Years of SU8 as MEMS Material

    Directory of Open Access Journals (Sweden)

    Arnaud Bertsch

    2015-06-01

    Full Text Available In 1997, the first paper using SU-8 as a material for microfabrication was published [1], demonstrating the interest of this negative photoresist for the near-UV structuration of thick layers and the manufacturing of high aspect-ratio components.[...

  8. Fabrication of SU-8 low frequency electrostatic energy harvester

    KAUST Repository

    Ramadan, Khaled S.; Foulds, Ian G.

    2011-01-01

    A 1500μm × 1500μm × 150μm out-of-plane, gap closing, electrostatic energy harvester is designed and fabricated to harvest low-frequency ambient vibrations. SU-8 is used to fabricate the proof mass (1200μm × 1200μm × 150μm) and the 5 m springs

  9. SU-8 as a material for lab-on-a-chip-based mass spectrometry.

    Science.gov (United States)

    Arscott, Steve

    2014-10-07

    This short review focuses on the application of SU-8 for the microchip-based approach to the miniaturization of mass spectrometry. Chip-based mass spectrometry will make the technology commonplace and bring benefits such as lower costs and autonomy. The chip-based miniaturization of mass spectrometry necessitates the use of new materials which are compatible with top-down fabrication involving both planar and non-planar processes. In this context, SU-8 is a very versatile epoxy-based, negative tone resist which is sensitive to ultraviolet radiation, X-rays and electron beam exposure. It has a very wide thickness range, from nanometres to millimetres, enabling the formation of mechanically rigid, very high aspect ratio, vertical, narrow width structures required to form microfluidic slots and channels for laboratory-on-a-chip design. It is also relatively chemically resistant and biologically compatible in terms of the liquid solutions used for mass spectrometry. This review looks at the impact and potential of SU-8 on the different parts of chip-based mass spectrometry - pre-treatment, ionization processes, and ion sorting and detection.

  10. A novel IPTV program multiplex access system to EPON

    Science.gov (United States)

    Xu, Xian; Liu, Deming; He, Wei; Lu, Xi

    2007-11-01

    With the rapid development of high speed networks, such as Ethernet Passive Optical Network (EPON), traffic patterns in access networks have evolved from traditional text-oriented service to the mixed text-, voice- and video- based services, leading to so called "Triple Play". For supporting IPTV service in EPON access network infrastructure, in this article we propose a novel IPTV program multiplex access system to EPON, which enables multiple IPTV program source servers to seamlessly access to IPTV service access port of optical line terminal (OLT) in EPON. There are two multiplex schemes, namely static multiplex scheme and dynamic multiplex scheme, in implementing the program multiplexing. Static multiplex scheme is to multiplex all the IPTV programs and forward them to the OLT, regardless of the need of end-users. While dynamic multiplex scheme can dynamically multiplex and forward IPTV programs according to what the end-users actually demand and those watched by no end-user would not be multiplexed. By comparing these two schemes, a reduced traffic of EPON can be achieved by using dynamic multiplex scheme, especially when most end-users are watching the same few IPTV programs. Both schemes are implemented in our system, with their hardware and software designs described.

  11. SU-8-based microneedles for in vitro neural applications

    International Nuclear Information System (INIS)

    Altuna, Ane; Tijero, María; Berganzo, Javier; Salido, Rafa; Fernández, Luis J; Gabriel, Gemma; Guimerá, Anton; Villa, Rosa; Menéndez de la Prida, Liset

    2010-01-01

    This paper presents novel design, fabrication, packaging and the first in vitro neural activity recordings of SU-8-based microneedles. The polymer SU-8 was chosen because it provides excellent features for the fabrication of flexible and thin probes. A microprobe was designed in order to allow a clean insertion and to minimize the damage caused to neural tissue during in vitro applications. In addition, a tetrode is patterned at the tip of the needle to obtain fine-scale measurements of small neuronal populations within a radius of 100 µm. Impedance characterization of the electrodes has been carried out to demonstrate their viability for neural recording. Finally, probes are inserted into 400 µm thick hippocampal slices, and simultaneous action potentials with peak-to-peak amplitudes of 200–250 µV are detected.

  12. Investigation of the bond strength between the photo-sensitive polymer SU-8 and Au

    DEFF Research Database (Denmark)

    Nordstrom, Maria; Johansson, Alicia; Sanches-Noguerón, E.

    2004-01-01

    promotors between the SU-8 and Au (ii) the effect of the processing sequence, either keeping SU-8 as bottum layer or Au (iii) varying the UV exposure dosage of the SU-8. For comparison, also the bond strength between SU-8 and other materials was measured. We report on bond strength of 4.8 +/- 1.2 MPa...

  13. Carbonization of SU-8 Based Electrode for MEMS Supercapacitors

    OpenAIRE

    Liu, Yang

    2014-01-01

    Supercapacitors are more sustainable and environmentally friendly energy sources than traditional ones. To achieve the supercapacitors with both energy density and power density that mainly depend on the effective surface area of theelectrodes, SU-8 can be used for electrode material to fabricate 3D microstructures as the electrodes that increase the effective surface area significantly. The objective of this project is to fabricate the reliable electrodes of large surface area for supercapac...

  14. Fabrication of SU-8 microstructures for analytical microfluidic applications

    OpenAIRE

    Tuomikoski, Santeri

    2007-01-01

    Miniaturization of analytical devices has been an ongoing trend to improve performance of analytical tools. These systems have been microfabricated originally of silicon and glass, but polymers have become increasingly popular as alternative materials. Polymers are mostly used because the material costs are lower and fabrication processes are easier. However, those facts depend heavily on the fabrication method and particular polymer. In this thesis the usability of epoxy-polymer SU-8 has bee...

  15. SU-8 Guiding Layer for Love Wave Devices

    Directory of Open Access Journals (Sweden)

    Michael I. Newton

    2007-11-01

    Full Text Available SU-8 is a technologically important photoresist used extensively for thefabrication of microfluidics and MEMS, allowing high aspect ratio structures to beproduced. In this work we report the use of SU-8 as a Love wave sensor guiding layerwhich allows the possibility of integrating a guiding layer with flow cell during fabrication.Devices were fabricated on ST-cut quartz substrates with a single-single finger design suchthat a surface skimming bulk wave (SSBW at 97.4 MHz was excited. SU-8 polymer layerswere successively built up by spin coating and spectra recorded at each stage; showing afrequency decrease with increasing guiding layer thickness. The insertion loss andfrequency dependence as a function of guiding layer thickness was investigated over thefirst Love wave mode. Mass loading sensitivity of the resultant Love wave devices wasinvestigated by deposition of multiple gold layers. Liquid sensing using these devices wasalso demonstrated; water-glycerol mixtures were used to demonstrate sensing of density-viscosity and the physical adsorption and removal of protein was also assessed usingalbumin and fibrinogen as model proteins.

  16. Plasma etching of polymers like SU8 and BCB

    Science.gov (United States)

    Mischke, Helge; Gruetzner, Gabi; Shaw, Mark

    2003-01-01

    Polymers with high viscosity, like SU8 and BCB, play a dominant role in MEMS application. Their behavior in a well defined etching plasma environment in a RIE mode was investigated. The 40.68 MHz driven bottom electrode generates higher etch rates combined with much lower bias voltages by a factor of ten or a higher efficiency of the plasma with lower damaging of the probe material. The goal was to obtain a well-defined process for the removal and structuring of SU8 and BCB using fluorine/oxygen chemistry, defined using variables like electron density and collision rate. The plasma parameters are measured and varied using a production proven technology called SEERS (Self Excited Electron Resonance Spectroscopy). Depending on application and on Polymer several metals are possible (e.g., gold, aluminum). The characteristic of SU8 and BCB was examined in the case of patterning by dry etching in a CF4/O2 chemistry. Etch profile and etch rate correlate surprisingly well with plasma parameters like electron density and electron collision rate, thus allowing to define to adjust etch structure in situ with the help of plasma parameters.

  17. Symmetry hierarchies and radiative corrections in the grand unified model SU(8)/sub L/ x SU(8)/sub R/

    International Nuclear Information System (INIS)

    Pirogov, Y.F.

    1982-01-01

    In the SU(8)/sub L/ x SU(8)/sub R/ model of precocious chiral unification, radiative corrections for the effective parameters sin 2 theta/sub W/(μ) and α(μ) are calculated in the one-loop approximation, neglecting contributions of the Higgs fields, and the unification mass M 8 is determined in the presence of a hierarchy of intermediate symmetries. It is shown that a natural hierarchy exists which leads to a decrease in sin 2 theta/sub W/(M/sub W/L) down to the value sin 2 theta/sub W/ = (1/5)--(1/4) together with a decrease in M 8 down to M 8 = 10 6 --10 7 GeV in comparison with the values in the absence of a hierarchy

  18. Reducing Attendance Time in LR-EPONs With Differentiated Services

    KAUST Repository

    Elrasad, Amr

    2015-04-09

    This work presents a novel on-the-fly void filling scheme for Long-Reach EPON called Size Controlled Batch Void Filling (SCBVF). SCBVF aims at reducing the time between consecutive bandwidth grants (attendance time) and hence reducing the average delay for delay-sensitive traffic.

  19. A Practical Approach For Excess Bandwidth Distribution for EPONs

    KAUST Repository

    Elrasad, Amr

    2014-03-09

    This paper introduces a novel approach called Delayed Excess Scheduling (DES), which practically reuse the excess bandwidth in EPONs system. DES is suitable for the industrial deployment as it requires no timing constraint and achieves better performance compared to the previously reported schemes.

  20. Functionalization of SU-8 Photoresist Surfaces with IgG Proteins

    DEFF Research Database (Denmark)

    Blagoi, Gabriela; Keller, Stephan Urs; Johansson, Alicia

    2008-01-01

    immunoassays were employed to characterize the binding efficiency of model proteins to bare SU-8 surface, SU-8 treated with cerium ammonium nitrate (CAN) etchant and CAN treated surfaces modified by aminosilanization. The highest binding capacity of antibodies was observed on bare SU-8. This explains why bare...... SU-8 in a functional fluorescent sandwich immunoassay detecting C-reactive protein (CRP) gave twice as high signal as compared with the other two surfaces. Immunoassays performed on bare SU-8 and CAN treated SU-8 resulted in detection limits of CRP of 30 and 80 ng/ml respectively which is sufficient...... for detecting CRP in clinical samples, where concentrations of 3–10 μg/ml are normal for healthy individuals. In conclusion, bare SU-8 and etched SU-8 can be modified with antibodies by a simple adsorption procedure which simplifies building lab-on-a-chip systems in SU-8. Additionally, we report the fabrication...

  1. Functionalization of SU-8 photoresist surfaces with IgG proteins

    International Nuclear Information System (INIS)

    Blagoi, Gabriela; Keller, Stephan; Johansson, Alicia; Boisen, Anja; Dufva, Martin

    2008-01-01

    The negative epoxy-based photoresist SU-8 has a variety of applications within microelectromechanical systems (MEMS) and lab-on-a-chip systems. Here, several methods to functionalize SU-8 surfaces with IgG proteins were investigated. Fluorescent labeled proteins and fluorescent sandwich immunoassays were employed to characterize the binding efficiency of model proteins to bare SU-8 surface, SU-8 treated with cerium ammonium nitrate (CAN) etchant and CAN treated surfaces modified by aminosilanization. The highest binding capacity of antibodies was observed on bare SU-8. This explains why bare SU-8 in a functional fluorescent sandwich immunoassay detecting C-reactive protein (CRP) gave twice as high signal as compared with the other two surfaces. Immunoassays performed on bare SU-8 and CAN treated SU-8 resulted in detection limits of CRP of 30 and 80 ng/ml respectively which is sufficient for detecting CRP in clinical samples, where concentrations of 3-10 μg/ml are normal for healthy individuals. In conclusion, bare SU-8 and etched SU-8 can be modified with antibodies by a simple adsorption procedure which simplifies building lab-on-a-chip systems in SU-8. Additionally, we report the fabrication process and use of microwells created in a SU-8 layer with the same dimensions as a standard microscope glass slide that could fit into fluorescent scanners. The SU-8 microwells minimize the reagent consumption and are straightforward to handle compared to SU-8 coated microscope slides

  2. Fabrication of high-aspect ratio SU-8 micropillar arrays

    DEFF Research Database (Denmark)

    Amato, Letizia; Keller, Stephan S.; Heiskanen, Arto

    2012-01-01

    to the resolution limit of photolithography. This paper describes process optimization for the fabrication of dense SU-8 micropillar arrays (2.5μm spacing) with nominal height ⩾20μm and nominal diameter ⩽2.5μm (AR ⩾8). Two approaches, differing in temperature, ramping rate and duration of the baking steps were...... compared as part of the photolithographic processing, in order to evaluate the effect of baking on the pattern resolution. Additionally, during the post-processing, supercritical point drying and hard baking were introduced yielding pillars with diameter 1.8μm, AR=11 and an improved temporal stability....

  3. A High-Throughput SU-8Microfluidic Magnetic Bead Separator

    DEFF Research Database (Denmark)

    Bu, Minqiang; Christensen, T. B.; Smistrup, Kristian

    2007-01-01

    We present a novel microfluidic magnetic bead separator based on SU-8 fabrication technique for high through-put applications. The experimental results show that magnetic beads can be captured at an efficiency of 91 % and 54 % at flow rates of 1 mL/min and 4 mL/min, respectively. Integration...... of soft magnetic elements in the chip leads to a slightly higher capturing efficiency and a more uniform distribution of captured beads over the separation chamber than the system without soft magnetic elements....

  4. SU-8 etching in inductively coupled oxygen plasma

    DEFF Research Database (Denmark)

    Rasmussen, Kristian Hagsted; Keller, Stephan Sylvest; Jensen, Flemming

    2013-01-01

    Structuring or removal of the epoxy based, photo sensitive polymer SU-8 by inductively coupled plasma reactive ion etching (ICP-RIE) was investigated as a function of plasma chemistry, bias power, temperature, and pressure. In a pure oxygen plasma, surface accumulation of antimony from the photo......-initiator introduced severe roughness and reduced etch rate significantly. Addition of SF6 to the plasma chemistry reduced the antimony surface concentration with lower roughness and higher etch rate as an outcome. Furthermore the etch anisotropy could be tuned by controlling the bias power. Etch rates up to 800 nm...

  5. SU-8 hollow cantilevers for AFM cell adhesion studies

    Science.gov (United States)

    Martinez, Vincent; Behr, Pascal; Drechsler, Ute; Polesel-Maris, Jérôme; Potthoff, Eva; Vörös, Janos; Zambelli, Tomaso

    2016-05-01

    A novel fabrication method was established to produce flexible, transparent, and robust tipless hollow atomic force microscopy (AFM) cantilevers made entirely from SU-8. Channels of 3 μm thickness and several millimeters length were integrated into 12 μm thick and 40 μm wide cantilevers. Connected to a pressure controller, the devices showed high sealing performance with no leakage up to 6 bars. Changing the cantilever lengths from 100 μm to 500 μm among the same wafer allowed the targeting of various spring constants ranging from 0.5 to 80 N m-1 within a single fabrication run. These hollow polymeric AFM cantilevers were operated in the optical beam deflection configuration. To demonstrate the performance of the device, single-cell force spectroscopy experiments were performed with a single probe detaching in a serial protocol more than 100 Saccharomyces cerevisiae yeast cells from plain glass and glass coated with polydopamine while measuring adhesion forces in the sub-nanoNewton range. SU-8 now offers a new alternative to conventional silicon-based hollow cantilevers with more flexibility in terms of complex geometric design and surface chemistry modification.

  6. SU-8 hollow cantilevers for AFM cell adhesion studies

    International Nuclear Information System (INIS)

    Martinez, Vincent; Behr, Pascal; Vörös, Janos; Zambelli, Tomaso; Drechsler, Ute; Polesel-Maris, Jérôme; Potthoff, Eva

    2016-01-01

    A novel fabrication method was established to produce flexible, transparent, and robust tipless hollow atomic force microscopy (AFM) cantilevers made entirely from SU-8. Channels of 3 μm thickness and several millimeters length were integrated into 12 μm thick and 40 μm wide cantilevers. Connected to a pressure controller, the devices showed high sealing performance with no leakage up to 6 bars. Changing the cantilever lengths from 100 μm to 500 μm among the same wafer allowed the targeting of various spring constants ranging from 0.5 to 80 N m −1 within a single fabrication run. These hollow polymeric AFM cantilevers were operated in the optical beam deflection configuration. To demonstrate the performance of the device, single-cell force spectroscopy experiments were performed with a single probe detaching in a serial protocol more than 100 Saccharomyces cerevisiae yeast cells from plain glass and glass coated with polydopamine while measuring adhesion forces in the sub-nanoNewton range. SU-8 now offers a new alternative to conventional silicon-based hollow cantilevers with more flexibility in terms of complex geometric design and surface chemistry modification. (paper)

  7. Tailoring the mechanical properties of SU-8/clay nanocomposites: polymer microcantilever fabrication perspective

    CSIR Research Space (South Africa)

    Chen, H

    2014-03-01

    Full Text Available SU-8/Clay nanocomposite is considered as a candidate material for microcantilever sensor fabrication. Organically modified montmorillonite clay nanoparticles are dispersed in the universally used negative photoresist polymer SU-8, for a low cost...

  8. A proof of concept of a BioMEMS glucose biosensor using microfabricated SU-8 films

    OpenAIRE

    Psoma, Sotiria D.

    2009-01-01

    The present project investigated and proved the concept of developing a novel BioMEMS glucose micro-biosensor using a simple one-step microfabrication process of the widely used SU-8 polymer. More specifically, the study focused on the investigation of the suitability of the SU-8 polymer as a matrix for enzyme immobilisation that is carried out during the microfabrication process. A comparative study between commercially available SU-8 and “customised” SU-8 solutions showed tha...

  9. Fabrication of SU-8 low frequency electrostatic energy harvester

    KAUST Repository

    Ramadan, Khaled S.

    2011-11-01

    A 1500μm × 1500μm × 150μm out-of-plane, gap closing, electrostatic energy harvester is designed and fabricated to harvest low-frequency ambient vibrations. SU-8 is used to fabricate the proof mass (1200μm × 1200μm × 150μm) and the 5 m springs. Different harvesters were designed to harvest at 50, 75 and 110 Hz. At 110 Hz, Simulations show that with an input vibration of 10 μm amplitude at the frequency of resonance of the structure, the energy harvester should generate an average output power density of 0.032μW/mm3. This is the most area-efficient low-frequency electrostatic harvester to-date. © 2011 IEEE.

  10. Gold Nanoparticles-Coated SU-8 for Sensitive Fluorescence-Based Detections of DNA

    DEFF Research Database (Denmark)

    Cao, Cuong; Birtwell, Sam W.; Høgberg, Jonas

    2012-01-01

    SU-8 epoxy-based negative photoresist has been extensively employed as a structural material for fabrication of numerous biological microelectro-mechanical systems (Bio-MEMS) or lab-on-a-chip (LOC) devices. However, SU-8 has a high autofluorescence level that limits sensitivity of microdevices...... for various Bio-MEMs and LOC devices that use SU-8 as a structural material....

  11. A Fast Channel Switching Method in EPON System for IPTV Service

    Science.gov (United States)

    Nie, Yaling; Yoshiuchi, Hideya

    This paper presents a fast channel switching method in Ethernet Passive Optical Network (EPON) system for IPTV service. Fast channel switching is one of the important features of successful IPTV systems. Users surely prefer IPTV systems with small channel switching time rather than a longer one. Thus a channel switching control module and a channel/permission list in EPON system’s ONU or OLT is designed. When EPON system receives channel switching message from IPTV end user, the channel switching control module will catch the message and search the channel list and permission list maintained in EPON system, then got the matching parameter of EPON for the new channel. The new channel’s data transmission will be enabled by directly updating the optical filter of the ONU that end user connected. By using this method in EPON system, it provides a solution for dealing with channel switching delays in IPTV service.

  12. Downstream-based Scheduling for Energy Conservation in Green EPONs

    KAUST Repository

    Chen, Shen

    2012-05-01

    Maximizing the optical network unit’s (ONU) sleep time is an effective approach for achieving maximum energy conservation in green Ethernet passive optical networks (EPONs). While overlapping downstream and upstream ONU transmissions can maximize the ONU sleep time, it jeopardizes the quality of service (QoS) performance of the network, especially for downstream traffic in case the overlapping is based on the upstream time slot. In this paper, we study the downstream traffic performance in green EPONs under the limited service discipline and the upstream-based overlapped time window. Specifically, we first derive the expected mean packet delay, and then present a closed-form expression of the ONU sleep time, setting identical upstream/downstream transmission cycle times based on a maximum downstream traffic delay re-quirement. With the proposed system model, we present a novel downstream bandwidth allocation scheme for energy conservation in green EPONs. Simulation results verify the proposed model and highlight the advantages of our scheme over conventional approaches.

  13. SU(8) family unification with boson-fermion balance

    CERN Multimedia

    CERN. Geneva

    2014-01-01

    Grand unification has been intensively investigated for over forty years, and many different approaches have been tried. In this talk I propose a model that involves three ingredients that do not appear in the usual constructions: (1) boson--fermion balance without full supersymmetry, (2) canceling the spin 1/2 fermion gauge anomalies against the anomaly from a gauged spin 3/2 gravitino, and (3) using a scalar field representation with non-zero U(1) generator to break the SU(8) gauge symmetry through a ground state which, before dynamical symmetry breaking, has a periodic U(1) generator structure. The model has a number of promising features: (1) natural incorporation of three families, (2) incorporation of the experimentally viable flipped SU(5) model, (3) a symmetry breaking pathway to the standard model using the scalar field required by boson-fermion balance, together with a stage of most attractive channel dynamical symmetry breaking, without postulating additional Higgs fields, (4) vanishing of bare Yuk...

  14. Surface modification of SU-8 for metal/SU-8 adhesion using RF plasma treatment for application in thermopile detectors

    International Nuclear Information System (INIS)

    Ashraf, Shakeel; Mattsson, Claes G; Thungström, Göran; Fondell, Mattis; Lindblad, Andreas

    2015-01-01

    This article reports on plasma treatment of SU-8 epoxy in order to enhance adhesive strength for metals. Its samples were fabricated on standard silicon wafers and treated with (O 2 and Ar) RF plasma at a power of 25 W at a low pressure of (3 × 10 −3 Torr) for different time spans (10–70 s). The sample surfaces were characterized in terms of contact angle, surface (roughness and chemistry) and using a tape test. During the contact angle measurement, it was observed that the contact angle was reduced from 73° to 5° (almost wet) and 23° for (O 2 and Ar) treated samples, respectively. The root mean square surface roughness was significantly increased by 21.5% and 37.2% for (O 2 and Ar) treatment, respectively. A pattern of metal squares was formed on the samples using photolithography for a tape test. An adhesive tape was applied to the samples and peeled off at 180°. The maximum adhesion results, more than 90%, were achieved for the O 2 -treated samples, whereas the Ar-treated samples showed no change. The XPS study shows the formation of new species in the O 2 -treated sample compared to the Ar-treated samples. The high adhesive results were due to the formation of hydrophilic groups and new O 2 species in the O 2 -treated samples, which were absent in Ar-treated samples. (paper)

  15. Uniform fabrication of thick SU-8 patterns on small-sized wafers for micro-optics applications

    Science.gov (United States)

    Abada, S.; Reig, B.; Daran, E.; Doucet, JB; Camps, T.; Charlot, S.; Bardinal, V.

    2014-05-01

    This paper reports on an alternative method for precise and uniform fabrication of 100μm-thick SU-8 microstructures on small-sized or non-circular samples. Standard spin-coating of high-viscosity resists is indeed known to induce large edge beads, leading to an air gap between the mask and the SU-8 photo-resist surface during UV photolithography. This results in a non uniform thickness deposition and in a poor pattern definition. This problem becomes highly critical in the case of small-sized samples. To overcome it, we have developed a soft thermal imprint method based on the use of a nano-imprint equipment and applicable whatever sample fragility, shape and size (from 2cm to 6 inches). After final photolithography, the SU8 pattern thickness variation profile is measured. Thickness uniformity is improved from 30% to 5% with a 5μm maximal deviation to the target value over 2cm-long samples.

  16. A Simple Hydrophilic Treatment of SU-8 Surfaces for Cell Culturing and Cell Patterning

    DEFF Research Database (Denmark)

    Wang, Zhenyu; Stangegaard, Michael; Dufva, Hans Martin

    2005-01-01

    SU-8, an epoxy-based photoresist, widely used in constitution different mTAS systems, is incompatible with mammalian cell adhesion and culture in its native form. Here, we demonstrate a simple, cheap and robust two-step method to render a SU-8 surface hydrophilic and compatible with cell culture........ The contact angle of SU-8 surface was significantly reduced from 90° to 25° after the surface modification. The treated SU-8 surfaces provided a cell culture environment that was comparable with cell culture flask surface in terms of generation time and morphology....

  17. Surface Modification of Photoresist SU-8 for Low Autofluorescence and Bioanalytical Applications

    DEFF Research Database (Denmark)

    Cao, Cuong; Birtwell, Sam W.; Høgberg, Jonas

    2011-01-01

    This paper reports a surface modification of epoxy-based negative photoresist SU-8 for reducing its autofluorescence while enhancing its biofunctionality. By covalently depositing a thin layer of 20 nm Au nanoparticles (AuNPs) onto the SU-8 surface, we found that the AuNPs-coated SU-8 surface...... is much less fluorescent than the untreated SU-8. Moreover, DNA probes can easily be immobilized on the Au surface and are thermally stable over a wide range of temperature. These improvements will benefit bioanalytical applications such as DNA hybridization and solid-phase PCR (SP-PCR)....

  18. SU-8 Composite Based “Lube-tape” for a Wide Range of Tribological Applications

    Directory of Open Access Journals (Sweden)

    Prabakaran Saravanan

    2014-05-01

    Full Text Available In a previous work, we have developed a perflouropolyether (PFPE lubricant droplet-filled SU-8 composite which promotes bonding between the molecules of SU-8 and PFPE and provides excellent boundary lubrication. The SU-8 + PFPE composite has enhanced the wear durability of SU-8 by more than four orders of magnitude. In this work, the same SU-8 + PFPE composite was used to fabricate a stand-alone laminate film called “Lube-tape”. It has integrated two layers of approximately 90 microns thickness each; the top layer is made of SU-8 + PFPE composite and the bottom layer of pristine SU-8. Thus, a single tape can have drastically contrasting high friction and low friction properties on its two surfaces. The composite side has the initial coefficient of friction ~7 times lower and the wear life more than four orders of magnitude than those of the pristine SU-8 side. This lube tape can be used on any load bearing surface to improve the tribological performance by simply pasting the pristine SU-8 side onto the substrate.

  19. Bandwidth Allocation Method by Service for WDM EPON

    Institute of Scientific and Technical Information of China (English)

    Yongseok; Chang; Changgyu; Choi; Jonghoon; Eom; Sungho; Kim

    2003-01-01

    A WDM(Wavelength Division Multiplexing) EPON(Ethernet Passive Optical Network) is an economical and efficient access network that has attracted significant research attention in recent years. A MAC(Media Access Control) Protocol of PON is based on TDMA(Time Division Multiple Access) basically, we can classify this protocol into a fixed length slot assignment method suitable for leased line supporting Qos(Quality of Service) and a variable length slot assignment method suitable for LAN/MAN with the best ...

  20. Deep proton writing of high aspect ratio SU-8 micro-pillars on glass

    Energy Technology Data Exchange (ETDEWEB)

    Ebraert, Evert, E-mail: eebraert@b-phot.org; Rwamucyo, Ben; Thienpont, Hugo; Van Erps, Jürgen

    2016-12-15

    Deep proton writing (DPW) is a fabrication technology developed for the rapid prototyping of polymer micro-structures. We use SU-8, a negative resist, spincoated in a layer up to 720 μm-thick in a single step on borosilicate glass, for irradiation with a collimated 12 MeV energy proton beam. Micro-pillars with a slightly conical profile are irradiated in the SU-8 layer. We determine the optimal proton fluence to be 1.02 × 10{sup 4} μm{sup −2}, with which we are able to repeatably achieve micro-pillars with a top-diameter of 138 ± 1 μm and a bottom-diameter of 151 ± 3 μm. The smallest fabricated pillars have a top-diameter of 57 ± 5 μm. We achieved a root-mean-square sidewall surface roughness between 19 nm and 35 nm for the fabricated micro-pillars, measured over an area of 5 × 63.7 μm. We briefly discuss initial testing of two potential applications of the fabricated micro-pillars. Using ∼100 μm-diameter pillars as waveguides for gigascale integration optical interconnect applications, has shown a 4.7 dB improvement in optical multimode fiber-to-fiber coupling as compared to the case where an air–gap is present between the fibers at the telecom wavelength of 1550 nm. The ∼140 μm-diameter pillars were used for mold fabrication with silicone casting. The resulting mold can be used for hydrogel casting, to obtain hydrogel replicas mimicking human tissue for in vitro bio-chemical applications.

  1. Overflow control mechanism (OCM) for Ethernet passive optical networks (EPONs)

    Science.gov (United States)

    Hajduczenia, Marek; da Silva, Henrique J. A.; Monteiro, Paulo P.

    2007-05-01

    The nonfragmentable nature of Ethernet data frames, as well as operation of the priority oriented packet schedulers in the optical network units, in conjunction with heavy network load conditions and the lack of detailed knowledge about the queue's composition at the optical line terminal (OLT) level, result in the creation of upstream channel slot remainders. The existing methods, in the form of nonpreemptive packet schedulers and multithreshold reporting process defined vaguely by the IEEE 802.3-2005 standard, result in either increased packet delay or Ethernet passive optical network (EPON) system incompatibility, respectively, since threshold processing was never officially defined in the scope of the respective EPON standard. We propose an alternative approach, based on basic modifications of the standard and extended GATE multipoint control protocol data unit format and meaning, allowing for the OLT packet scheduling agent to grant always exactly the requested slot size, thus preventing creation of any upstream channel slot remainders. It is estimated that, on average, ˜3% of upstream channel bandwidth can be salvaged when slot remainders are absent in the upstream channel transmission.

  2. A design and implementation of IPTV STB over EPON

    Science.gov (United States)

    Zhang, Shu; Liu, Deming; Wang, Jinjuan; Chang, Yuguang

    2007-11-01

    In this paper, a system of digital television over EPON is first introduced. System structure and working process are described in detail, including technology scheme of each part. According to DVB-C, digital TV signal is first received, then TS streams are de-multiplexed and decrypted and so IP stream made up of TS streams is transmitted in EPON. Then, as the most important terminal device on the side of users, STB receives Ethernet data, gets the MPEG-2 TS through network processing. After that, STB parses TS file, decodes video and audio, analyzes SI data, and sends the gained data to TV to display video and EPG. Besides, STB fulfills the web browser. According to the function of the system, technical requirements and main scheme of an IPTV STB are analyzed and realized. It's based on AMD Au1200 processor with Linux operation system. The hardware and software architectures are introduced, together with functional description of every part. We realize all modules required and the experiment shows a good performance of facility and stability.

  3. A Review on Surface Stress-Based Miniaturized Piezoresistive SU-8 Polymeric Cantilever Sensors

    Science.gov (United States)

    Mathew, Ribu; Ravi Sankar, A.

    2018-06-01

    In the last decade, microelectromechanical systems (MEMS) SU-8 polymeric cantilevers with piezoresistive readout combined with the advances in molecular recognition techniques have found versatile applications, especially in the field of chemical and biological sensing. Compared to conventional solid-state semiconductor-based piezoresistive cantilever sensors, SU-8 polymeric cantilevers have advantages in terms of better sensitivity along with reduced material and fabrication cost. In recent times, numerous researchers have investigated their potential as a sensing platform due to high performance-to-cost ratio of SU-8 polymer-based cantilever sensors. In this article, we critically review the design, fabrication, and performance aspects of surface stress-based piezoresistive SU-8 polymeric cantilever sensors. The evolution of surface stress-based piezoresistive cantilever sensors from solid-state semiconductor materials to polymers, especially SU-8 polymer, is discussed in detail. Theoretical principles of surface stress generation and their application in cantilever sensing technology are also devised. Variants of SU-8 polymeric cantilevers with different composition of materials in cantilever stacks are explained. Furthermore, the interdependence of the material selection, geometrical design parameters, and fabrication process of piezoresistive SU-8 polymeric cantilever sensors and their cumulative impact on the sensor response are also explained in detail. In addition to the design-, fabrication-, and performance-related factors, this article also describes various challenges in engineering SU-8 polymeric cantilevers as a universal sensing platform such as temperature and moisture vulnerability. This review article would serve as a guideline for researchers to understand specifics and functionality of surface stress-based piezoresistive SU-8 cantilever sensors.[Figure not available: see fulltext.

  4. Design of EPON far-end equipment based on FTTH

    Science.gov (United States)

    Feng, Xiancheng; Yun, Xiang

    2008-12-01

    Now, most favors fiber access is mainly the EPON fiber access system. Inheriting from the low cost of Ethernet, usability and bandwidth of optical network, EPON technology is one of the best technologies in fiber access and is adopted by the carriers all over the world widely. According to the scheme analysis to FTTH fan-end equipment, hardware design of ONU is proposed in this paper. The FTTH far-end equipment software design deference modulation design concept, it divides the software designment into 5 function modules: the module of low-layer driver, the module of system management, the module of master/slave communication, and the module of main/Standby switch and the module of command line. The software flow of the host computer is also analyzed. Finally, test is made for Ethernet service performance of FTTH far-end equipment, E1 service performance and the optical path protection switching, and so on. The results of test indicates that all the items are accordance with technical request of far-end ONU equipment and possess good quality and fully reach the requirement of telecommunication level equipment. The far-end equipment of FTTH divides into several parts based on the function: the control module, the exchange module, the UNI interface module, the ONU module, the EPON interface module, the network management debugging module, the voice processing module, the circuit simulation module, the CATV module. In the downstream direction, under the protect condition, we design 2 optical modules. The system can set one group optical module working and another group optical module closure when it is initialized. When the optical fiber line is cut off, the LOS warning comes out. It will cause MUX to replace another group optical module, simultaneously will reset module 3701/3711 and will make it again test the distance, and will give the plug board MPC850 report through the GPIO port. During normal mode, the downstream optical signal is transformed into the

  5. Design of controllable multicast for IPTV over EPON

    Science.gov (United States)

    Zhang, Chuanhao; Liu, Deming; Zhang, Li; Wu, Guangsheng

    2007-11-01

    The character of 1Gbps bandwidth and tree-based structure make EPON very suitable for broadcast or multicast services such as IPTV. In this paper we focus on security mechanisms that should be available to groups that specifically request it, and therefore are willing to pay the extra cost of implementing those mechanisms. We concentrate on two issues: how unauthorized multicast traffic can be prevented by means of multicast transit traffic control; how a group's susceptibility is likely to be reduced by means of multicast group access control. We have proposed a novel scheme that should be available to multicast groups that desire precautionary measures be taken to avert the threats of Invalid source and unauthorized access.

  6. Single-mode waveguides with SU-8 polymer core and cladding for MOEMS applications

    DEFF Research Database (Denmark)

    Nordström, Maria; Zauner, Dan; Boisen, Anja

    2007-01-01

    Fabrication and optical characterization of singlemode polymeric embedded waveguides are performed. A specific material combination (SU-8 2005 as core and the modified SU-8 mr-L 6050XP as cladding) is chosen in order to obtain a small refractive index difference for single-mode propagation combined...... can fabricate waveguides with an index difference in the order of 10−3, where both the core material and the cladding material are based on SU-8. The refractive index measurements are performed on thin polymeric films, while further optical characterizations are performed on waveguides with a height...

  7. Energy Efficiency in Ethernet Passive Optical Networks (EPONs): Protocol Design and Performance Evaluation

    DEFF Research Database (Denmark)

    Yan, Ying; Dittmann, Lars

    2011-01-01

    a suitable wakeup time scheduler at the Optical Line Terminal (OLT). A generic EPON system is considered, which is composed of an OLT and several ONUs that are EMM enabled. An energy consumption optimization problem aimed at saving energy is proposed and two heuristic sleep mode scheduling policies......As concerns about energy consumption grow, the power consumption of the EPON becomes a matter of increasing importance. In respect of energy efficiency, the current standard has no management protocols aiming to reduce power consumption in EPONs. In this paper, we propose an Energy Management...... and guaranteeing the network performance at the same time. Simulation results show that an EMM-based EPON with well designed scheduling disciplines is essential to achieving significant energy saving while meeting the delay constraint....

  8. Thermodynamic and Mechanical Properties of Epon 862 With Curing Agent Detda by Molecular Simulation

    National Research Council Canada - National Science Library

    Tack, Jeremy L

    2006-01-01

    Fully atomistic molecular dynamics (MD) simulations were used to predict the properties of EPON 862 cross-linked with curing agent DETDA, a potentially useful epoxy resin for future applications of nanocomposites...

  9. Shock and Release Response of Unreacted Epon 828: Shot 2s-905

    Energy Technology Data Exchange (ETDEWEB)

    Pisa, Matthew Alexander [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fredenburg, David A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dattelbaum, Dana M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lang, John Michael [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Sandoval, Donald Leon [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-11-16

    This document summarizes the shock and release response of Epon 828 measured in the dynamic impact experiment 2s-905. Experimentally, a thin Kel-F impactor backed by a low impedance foam impacted an Epon 828 target with embedded electromagnetic gauges. Computationally, a one dimensional simulation of the impact event was performed, and tracer particles were located at the corresponding electromagnetic gauge locations. The experimental configuration was such that the Epon 828 target was initially shocked, and then allowed to release from the high-pressure state. Comparisons of the experimental gauge and computational tracer data were made to assess the performance of equation of state (EOS) 7603, a SESAME EOS for Epon 828, on and off the principal shock Hugoniot. Results indicate that while EOS 7603 can capture the Hugoniot response to better that 1%, while the sound speeds at pressure are under-predicted by 6 - 7%.

  10. A flexible solution for the next generation EPON with hybrid bidirectional 1Gbps and 10Gbps

    Science.gov (United States)

    Zhang, Weixun; Qiao, Yaojun; Li, Hui; Ji, Yuefeng

    2007-11-01

    Ethernet PON (EPON) has been proved to be a successful technology among all the standardized PON systems [1, 2], in terms of its cost-effective and large bandwidth virtue. And EPON has become a network of a choice for subscriber oriented digital service delivery, taking over the market previously dominated by DSL. However, with the development of advanced video services, the bandwidth capacity of current EPON seems to be not well suited for the future large deployment of triple-play services. Many researches are now taken about the Next Generation EPON; and the recent 10G EPON system standardization effort in the IEEE [3] results a lot of interest in the evolution of current PON systems towards high data rate system capable of providing a future-proof platform for delivery of personalized triple-play services. In this paper, a novel architecture of TDM-based 10GE-PON system is proposed. It combines the GE-PON and 10GE-PON systems, and provides symmetric 1Gbps/10Gbps or asymmetric access simultaneously. According to the results of the simulation on the system throughput and latency performance, the system is verified to be one solution and an important step from 1Gbit/s to 10Gbit/s for the Next Generation EPON.

  11. Fabrication of thin SU-8 cantilevers: initial bending, release and time stability

    DEFF Research Database (Denmark)

    Keller, Stephan Urs; Haefliger, D.; Boisen, Anja

    2010-01-01

    SU-8 cantilevers with a thickness of 2 mu m were fabricated using a dry release method and two steps of SU-8 photolithography. The processing of the thin SU-8 film defining the cantilevers was experimentally optimized to achieve low initial bending due to residual stress gradients. In parallel......, the rotational deformation at the clamping point allowed a qualitative assessment of the device release from the fluorocarbon-coated substrate. The change of these parameters during several months of storage at ambient temperature was investigated in detail. The introduction of a long hard bake in an oven after...... development of the thin SU-8 film resulted in reduced cantilever bending due to removal of residual stress gradients. Further, improved time-stability of the devices was achieved due to the enhanced cross-linking of the polymer. A post-exposure bake at a temperature T-PEB = 50 degrees C followed by a hard...

  12. A facile micropatterning method for a highly flexible PEDOT:PSS on SU-8

    KAUST Repository

    Cho, Nam Chul; Diekhans, Justin; Steward, Malia; Bakr, Osman; Choi, Seungkeun

    2016-01-01

    We report the micropatterning of conducting polymer on the epoxy-based photoresist to demonstrate fully organic, conducting and flexible electrodes. We show that polystyrene sulfonic acid can be covalently linked to the surface of the photoresist (SU-8) by forming sulfonyl ester at the interfaces. We also present an application of the patterned PEDOT:PSS (poly(3,4-ethylenedioxythiophene) polystyrene sulfonate)/SU-8 to the electroplating of metal electrodes. © 2016 Elsevier B.V.

  13. A facile micropatterning method for a highly flexible PEDOT:PSS on SU-8

    KAUST Repository

    Cho, Nam Chul

    2016-04-17

    We report the micropatterning of conducting polymer on the epoxy-based photoresist to demonstrate fully organic, conducting and flexible electrodes. We show that polystyrene sulfonic acid can be covalently linked to the surface of the photoresist (SU-8) by forming sulfonyl ester at the interfaces. We also present an application of the patterned PEDOT:PSS (poly(3,4-ethylenedioxythiophene) polystyrene sulfonate)/SU-8 to the electroplating of metal electrodes. © 2016 Elsevier B.V.

  14. Single-mode waveguides with SU-8 polymer core and cladding for MOEMS applications

    OpenAIRE

    Nordström, Maria; Zauner, Dan; Boisen, Anja; Hübner, Jörg

    2007-01-01

    Fabrication and optical characterization of singlemode polymeric embedded waveguides are performed. A specific material combination (SU-8 2005 as core and the modified SU-8 mr-L 6050XP as cladding) is chosen in order to obtain a small refractive index difference for single-mode propagation combined with the conventional fabrication method UV lithography to facilitate the integration of different types of optical detection methods on lab-on-a-chip systems. We analyze the behavior of the refrac...

  15. PDMS as a sacrificial substrate for SU-8-based biomedical and microfluidic applications

    International Nuclear Information System (INIS)

    Patel, Jasbir N; Kaminska, Bozena; Gray, Bonnie L; Gates, Byron D

    2008-01-01

    We describe a new fabrication process utilizing polydimethylesiloxane (PDMS) as a sacrificial substrate layer for fabricating free-standing SU-8-based biomedical and microfluidic devices. The PDMS-on-glass substrate permits SU-8 photo patterning and layer-to-layer bonding. We have developed a novel PDMS-based process which allows the SU-8 structures to be easily peeled off from the substrate after complete fabrication. As an example, a fully enclosed microfluidic chip has been successfully fabricated utilizing the presented new process. The enclosed microfluidic chip uses adhesive bonding technology and the SU-8 layers from 10 µm to 450 µm thick for fully enclosed microchannels. SU-8 layers as large as the glass substrate are successfully fabricated and peeled off from the PDMS layer as single continuous sheets. The fabrication results are supported by optical microscopy and profilometry. The peel-off force for the 120 µm thick SU-8-based chips is measured using a voice coil actuator (VCA). As an additional benefit the release step leaves the input and the output of the microchannels accessible to the outside world facilitating interconnecting to the external devices

  16. Investigation on the mechanism of nitrogen plasma modified PDMS bonding with SU-8

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Chengxin; Yuan, Yong J., E-mail: yongyuan@swjtu.edu.cn

    2016-02-28

    Graphical abstract: - Highlights: • Different nitrogen plasma processes modified PDMS bonding with SU-8 had been studied. • The effect of nitrogen plasma modification would produce the best result and the recovery of PDMS hydrophobicity could be delayed. - Abstract: Polydimethylsiloxane (PDMS) and SU-8 are both widely used for microfluidic system. However, it is difficult to permanently seal SU-8 microfluidic channels using PDMS with conventional methods. Previous efforts of combining these two materials mainly employed oxygen plasma modified PDMS. The nitrogen plasma modification of PDMS bonding with SU-8 is rarely studied in recent years. In this work, the mechanism of nitrogen plasma modified PDMS bonding with SU-8 was investigated. The fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and contact angle of a water droplet were used to analyze the nitrogen plasma modified surface and the hydrophilic stability of PDMS samples. Pull-off tests were used for estimating the bonding effect of interface between nitrogen plasma modified PDMS and SU-8.

  17. Effects of post exposure bake temperature and exposure time on SU-8 nanopattern obtained by electron beam lithography

    Science.gov (United States)

    Yasui, Manabu; Kazawa, Elito; Kaneko, Satoru; Takahashi, Ryo; Kurouchi, Masahito; Ozawa, Takeshi; Arai, Masahiro

    2014-11-01

    SU-8 is a photoresist imaged using UV rays. However, we investigated the characteristics of an SU-8 nanopattern obtained by electron beam lithography (EBL). In particular, we studied the relationship between post-exposure bake (PEB) temperature and exposure time on an SU-8 nanopattern with a focus on phase transition temperature. SU-8 residue was formed by increasing both PEB temperature and exposure time. To prevent the formation of this, Monte Carlo simulation was performed; the results of such simulation showed that decreasing the thickness of SU-8 can reduce the amount of residue from the SU-8 nanopattern. We confirmed that decreasing the thickness of SU-8 can also prevent the formation of residue from the SU-8 nanopattern with EBL.

  18. On symmetry hierarchy and radiative corrections in the grand unified model SU(8)sub(L)xSU(8)sub(R)

    International Nuclear Information System (INIS)

    Pirogov, Yu.F.

    1982-01-01

    In the model of precocious chiral unification SU(8)sub(L)xSU(8)sub(R) radiative corrections are calculated for the effective parameters sin 2 thetaw(μ) and α(μ) and the unification mass M 8 is determifed in presence of a hierarchy of intermediate symmetries. The one-loop approximation is used and contributions from the Higgs fields are neglected. It is shown that a natural hierarchy exists leading to a decrease of sinsup(2)thetasub(w)(Msub(wsub(L))) up to sinsup(2)thetasub(w)=1/5-1/4 together with a decrease of M 8 up to M 8 =10 6 -10 7 GeV, as compared with the magnitudes without the hierarchy [ru

  19. Effects of temperature on mechanical properties of SU-8 photoresist material

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Soon Wan; Park, Seung Bae [State University of New York, New York (United States)

    2013-09-15

    A representative fabrication processing of SU-8 photoresist, Ultraviolet (UV) lithography is usually composed of spin coat, soft bake, UV exposure, post exposure bake (PEB), development and optional hard bake, etc. The exposed region of SU-8 is crosslinked during the PEB process and its physical properties highly depend on UV exposure and PEB condition. This work was initiated to investigate if thermal baking after fabrication can affect the mechanical properties of SU-8 photoresist material because SU-8 is trying to be used as a structural material for MEMS operated at high temperature. Since a temperature of 95 .deg. C is normally recommended for PEB process, elevated temperatures up to 200 .deg. C were considered for the optional hard bake process. The viscoelastic material properties were measured by dynamic mechanical analyses (DMA). Also, pulling tests were performed to obtain Young's modulus and Poisson's ratio as a function of strain rate in a wide temperature range. From this study, the effects of temperature on the elastic and viscoelastic material properties of SU-8 were obtained.

  20. Effects of temperature on mechanical properties of SU-8 photoresist material

    International Nuclear Information System (INIS)

    Chung, Soon Wan; Park, Seung Bae

    2013-01-01

    A representative fabrication processing of SU-8 photoresist, Ultraviolet (UV) lithography is usually composed of spin coat, soft bake, UV exposure, post exposure bake (PEB), development and optional hard bake, etc. The exposed region of SU-8 is crosslinked during the PEB process and its physical properties highly depend on UV exposure and PEB condition. This work was initiated to investigate if thermal baking after fabrication can affect the mechanical properties of SU-8 photoresist material because SU-8 is trying to be used as a structural material for MEMS operated at high temperature. Since a temperature of 95 .deg. C is normally recommended for PEB process, elevated temperatures up to 200 .deg. C were considered for the optional hard bake process. The viscoelastic material properties were measured by dynamic mechanical analyses (DMA). Also, pulling tests were performed to obtain Young's modulus and Poisson's ratio as a function of strain rate in a wide temperature range. From this study, the effects of temperature on the elastic and viscoelastic material properties of SU-8 were obtained.

  1. 3-dimensional free standing micro-structures by proton beam writing of Su 8-silver nanoParticle polymeric composite

    Science.gov (United States)

    Igbenehi, H.; Jiguet, S.

    2012-09-01

    Proton beam lithography a maskless direct-write lithographic technique (well suited for producing 3-Dimensional microstructures in a range of resist and semiconductor materials) is demonstrated as an effective tool in the creation of electrically conductive freestanding micro-structures in an Su 8 + Nano Silver polymer composite. The structures produced show non-ohmic conductivity and fit the percolation theory conduction model of tunneling of separated nanoparticles. Measurements show threshold switching and a change in conductivity of at least 4 orders of magnitude. The predictable range of protons in materials at a given energy is exploited in the creation of high aspect ratio, free standing micro-structures, made from a commercially available SU8 Silver nano-composite (GMC3060 form Gersteltec Inc. a negative tone photo-epoxy with added metallic nano-particles(Silver)) to create films with enhanced electrical properties when exposed and cured. Nano-composite films are directly written on with a finely focused MeV accelerated Proton particle beam. The energy loss of the incident proton beams in the target polymer nano- composite film is concentrated at the end of its range, where damage occurs; changing the chemistry of the nano-composite film via an acid initiated polymerization - creating conduction paths. Changing the energy of the incident beams provide exposed regions with different penetration and damage depth - exploited in the demonstrated cantilever microstructure.

  2. Microchannel-connected SU-8 honeycombs by single-step projection photolithography for positioning cells on silicon oxide nanopillar arrays

    International Nuclear Information System (INIS)

    Larramendy, Florian; Paul, Oliver; Blatche, Marie Charline; Mazenq, Laurent; Laborde, Adrian; Temple-Boyer, Pierre

    2015-01-01

    We report on the fabrication, functionalization and testing of SU-8 microstructures for cell culture and positioning over large areas. The microstructure consists of a honeycomb arrangement of cell containers interconnected by microchannels and centered on nanopillar arrays designed for promoting cell positioning. The containers have been dimensioned to trap single cells and, with a height of 50 µm, prevent cells from escaping. The structures are fabricated using a single ultraviolet photolithography exposure with focus depth in the lower part of the SU-8 resist. With optimized process parameters, microchannels of various aspect ratios are thus produced. The cell containers and microchannels serve for the organization of axonal growth between neurons. The roughly 2 µm-high and 500 nm-wide nanopillars are made of silicon oxide structured by deep reactive ion etching. In future work, beyond their cell positioning purpose, the nanopillars could be functionalized as sensors. The proof of concept of the novel microstructure for organized cell culture is given by the successful growth of interconnected PC12 cells. Promoted by the honeycomb geometry, a dense network of interconnections between the cells has formed and the intended intimate contact of cells with the nanopillar arrays was observed by scanning electron microscopy. This proves the potential of these new devices as tools for the controlled cell growth in an interconnected container system with well-defined 3D geometry. (paper)

  3. Novel SU-8/Ionic Liquid Composite for Tribological Coatings and MEMS

    Directory of Open Access Journals (Sweden)

    Leili Batooli

    2015-05-01

    Full Text Available Tribology of SU-8 polymer is increasingly relevant due to bursting use of this material in a variety of applications. This study is directed towards introduction and investigation of a novel self-lubricating composite of an ionic liquid (IL in SU-8. The new material can be utilized for fabrication of lubricating polymer coating with tunable surface properties or SU8-made elements for microelectromechanical systems (MEMS with enhanced tribological performance. It is shown that addition of IL drastically alters water affinity of the composite while UV patternability remains unmodified. A lower coefficient of friction and wear has been obtained for two investigated compositions with 4 and 10 wt % ionic liquid.

  4. Immunosensing by luminescence reduction in surface-modified microstructured SU-8

    Energy Technology Data Exchange (ETDEWEB)

    Eravuchira, Pinkie Jacob; Baranowska, Malgorzata; Eckstein, Chris [Departament d’Enginyeria Electrònica, Elèctrica i Automàtica, Universitat Rovira i Virgili, Avda. Països Catalans 26, Tarragona 43007 (Spain); Díaz, Francesc [Departament de Química Física i Inorgànica, Universitat Rovira i Virgili, Marcelí Domingo s/n, Tarragona 43007 (Spain); Llobet, Eduard; Marsal, Lluis F. [Departament d’Enginyeria Electrònica, Elèctrica i Automàtica, Universitat Rovira i Virgili, Avda. Països Catalans 26, Tarragona 43007 (Spain); Ferré-Borrull, Josep, E-mail: josep.ferre@urv.cat [Departament d’Enginyeria Electrònica, Elèctrica i Automàtica, Universitat Rovira i Virgili, Avda. Països Catalans 26, Tarragona 43007 (Spain)

    2017-01-15

    Highlights: • The reduction of photoluminescence of SU-8 upon surface modification is reported. • Micropillar structuring of SU-8 surface results in an increased photoluminescence reduction rate (10% glass, 15% silicon). • Photoluminescence reduction rate can be a transduction parameter for the detection of antibody-antigen binding events. • The proposed sensing mechanism can be used to quantify small concentrations of antibody. • Lower limit of detection (LOD) of 28 μg/ml on silicon substrates and 42 μg/ml on glass substrates was achieved. - Abstract: SU-8, an epoxy based negative photoresist is extensively used as a structural material for the fabrication of microelectro-mechanical systems and in microelectronics technology. However, the possible applications of SU-8 for biosensing have not been explored much, mainly because of the photoluminescence SU-8 possesses in the near-UV and visible wavelength ranges which hinders fluorescent labelling of biorecognition events. In this study we demonstrate that photoluminescence of SU-8 can be employed itself as a sensing transduction parameter to produce a tool for immunosensing: the photoluminescence shows a systematic reduction upon modification of its surface chemistry, and in particular upon attachment of an antigen-antibody (aIgG-IgG) pair. We investigate the relation of the amount of reduction of photoluminescence on planar and microstructured surfaces, and we show that microstructuring leads to a higher reduction than a planar surface. Furthermore, we evaluated the dependence of photoluminescence reduction as a function of analyte concentration to prove that this magnitude can be applied to immunosensing.

  5. Polymer SU-8 Based Microprobes for Neural Recording and Drug Delivery

    Science.gov (United States)

    Altuna, Ane; Fernandez, Luis; Berganzo, Javier

    2015-06-01

    This manuscript makes a reflection about SU-8 based microprobes for neural activity recording and drug delivery. By taking advantage of improvements in microfabrication technologies and using polymer SU-8 as the only structural material, we developed several microprobe prototypes aimed to: a) minimize injury in neural tissue, b) obtain high-quality electrical signals and c) deliver drugs at a micrometer precision scale. Dedicated packaging tools have been developed in parallel to fulfill requirements concerning electric and fluidic connections, size and handling. After these advances have been experimentally proven in brain using in vivo preparation, the technological concepts developed during consecutive prototypes are discussed in depth now.

  6. POLYMER SU-8 BASED MICROPROBES FOR NEURAL RECORDING AND DRUG DELIVERY

    Directory of Open Access Journals (Sweden)

    Ane eAltuna

    2015-06-01

    Full Text Available This manuscript makes a reflection about SU-8 based microprobes for neural activity recording and drug delivery. By taking advantage of improvements in microfabrication technologies and using polymer SU-8 as the only structural material, we developed several microprobe prototypes aimed to: a minimize injury in neural tissue, b obtain high-quality electrical signals and c deliver drugs at a micrometer precision scale. Dedicated packaging tools have been developed in parallel to fulfill requirements concerning electric and fluidic connections, size and handling. After these advances have been experimentally proven in brain using in vivo preparation, the technological concepts developed during consecutive prototypes are discussed in depth now.

  7. Dense vertical SU-8 microneedles drawn from a heated mold with precisely controlled volume

    International Nuclear Information System (INIS)

    Xiang, Zhuolin; Wang, Hao; Yen, Shih-Cheng; Lee, Chengkuo; Murugappan, Suresh Kanna; Pastorin, Giorgia

    2015-01-01

    Drawing lithography technology has recently become a popular technique to fabricate (3D) microneedles. The conventional drawing process shows some limitations in fabricating dense, scale-up and small microneedles. In this study, we demonstrate a new drawing lithography process from a self-loading mold which is able to overcome these challenges. Different from the conventional molds which have difficult alignment and loading issues, a released SU-8 membrane is attached onto a SU-8 coated wafer to generate an innovative self-loading mold. The physically distinct SU-8 colloid in this mold successfully avoids the merging of the microneedle tips in the drawing process. Meanwhile, the same SU-8 colloid in mold can provide microneedles with uniform lengths on a large surface area. Furthermore, a low temperature drawing process with this improved technique prevents sharp tips from bending during the solidification stage. Remarkably, this new drawing lithography technology can fabricate microneedles with various lengths and they are strong enough to penetrate the outermost skin layer, namely the stratum corneum. The spacing between two adjacent microneedles is optimized to maximize the penetration rate through the skin. Histology images and drug diffusion testing demonstrate that microchannels are successfully created and the drugs can permeate the tissue under the skin. The fabricated microneedles are demonstrated to deliver insulin in vivo and lower blood glucose levels, suggesting future possible applications for minimally invasive transdermal delivery of macromolecules. (paper)

  8. Use of SU8 as a stable and biocompatible adhesion layer for gold bioelectrodes.

    Science.gov (United States)

    Matarèse, Bruno F E; Feyen, Paul L C; Falco, Aniello; Benfenati, Fabio; Lugli, Paolo; deMello, John C

    2018-04-03

    Gold is the most widely used electrode material for bioelectronic applications due to its high electrical conductivity, good chemical stability and proven biocompatibility. However, it adheres only weakly to widely used substrate materials such as glass and silicon oxide, typically requiring the use of a thin layer of chromium between the substrate and the metal to achieve adequate adhesion. Unfortunately, this approach can reduce biocompatibility relative to pure gold films due to the risk of the underlying layer of chromium becoming exposed. Here we report on an alternative adhesion layer for gold and other metals formed from a thin layer of the negative-tone photoresist SU-8, which we find to be significantly less cytotoxic than chromium, being broadly comparable to bare glass in terms of its biocompatibility. Various treatment protocols for SU-8 were investigated, with a view to attaining high transparency and good mechanical and biochemical stability. Thermal annealing to induce partial cross-linking of the SU-8 film prior to gold deposition, with further annealing after deposition to complete cross-linking, was found to yield the best electrode properties. The optimized glass/SU8-Au electrodes were highly transparent, resilient to delamination, stable in biological culture medium, and exhibited similar biocompatibility to glass.

  9. Novel method for chemical modification and patterning of the SU-8 photoresist

    DEFF Research Database (Denmark)

    Blagoi, Gabriela; Keller, Stephan Urs; Boisen, Anja

    2007-01-01

    the wetting behaviour of SU-8. The resolution limit of the AQ photopatterning method was 20 μm when using an uncollimated light source. AQ modification followed by a reaction with amino groups of Alexa-647 cadaverine and a Biotin-amino derivative proved possible modification and patterning of polymeric...

  10. Micro-particle filter made in SU-8 for biomedical applications

    DEFF Research Database (Denmark)

    Noeth, Nadine-Nicole; Keller, Stephan Urs; Fetz, Stefanie

    2009-01-01

    We have integrated a micro-particle filter in a polymer cantilever to filter micro-particles from a fluid while simultaneously measuring the amount of filtered particles. In a 3,8 mum thick SU-8 cantilever a filter was integrated with pore sizes between 3 and 30 mum. The chip was inserted in a mi...

  11. Humidity influence on the adhesion of SU-8 polymer from MEMS applications

    Directory of Open Access Journals (Sweden)

    Birleanu Corina

    2017-01-01

    Full Text Available In this paper, the adhesion behaviors of SU-8 polymer thin film from MEMS application were investigated as a function of relative humidity. The adhesion test between the AFM tip and SU-8 polymer have been extensively studied using the atomic force microscope (AFM, for a relative humidity (RH varying between 20 and 90%. The samples for tests are SU-8 polymers hard baked at different temperatures. The hard bake temperature changes the tribo-mechanical properties of polymers. The paper reports the measurements and the modeling of adhesion forces versus humidity in controlled ranges between 20 to 90%RH. To investigate the effect of relative humidity on adhesion for SU-8 polymer hard baked we used an analytical method which encompasses the effect of capillarity as well as the solid-to-solid interaction. While the capillary force expression is considered to be the sum of the superficial tension and the Laplace force for the solid-solid interaction is expressed by the Derjagin, Muller and Toropov (DMT model of solids adhesion. The analytical results obtained are in accordance with those obtained experimentally.

  12. MWP phase shifters integrated in PbS-SU8 waveguides.

    Science.gov (United States)

    Hervás, Javier; Suárez, Isaac; Pérez, Joaquín; Cantó, Pedro J Rodríguez; Abargues, Rafael; Martínez-Pastor, Juan P; Sales, Salvador; Capmany, José

    2015-06-01

    We present new kind of microwave phase shifters (MPS) based on dispersion of PbS colloidal quantum dots (QDs) in commercially available photoresist SU8 after a ligand exchange process. Ridge PbS-SU8 waveguides are implemented by integration of the nanocomposite in a silicon platform. When these waveguides are pumped at wavelengths below the band-gap of the PbS QDs, a phase shift in an optically conveyed (at 1550 nm) microwave signal is produced. The strong light confinement produced in the ridge waveguides allows an improvement of the phase shift as compared to the case of planar structures. Moreover, a novel ridge bilayer waveguide composed by a PbS-SU8 nanocomposite and a SU8 passive layer is proposed to decrease the propagation losses of the pump beam and in consequence to improve the microwave phase shift up to 36.5° at 25 GHz. Experimental results are reproduced by a theoretical model based on the slow light effect produced in a semiconductor waveguide due to the coherent population oscillations. The resulting device shows potential benefits respect to the current MPS technologies since it allows a fast tunability of the phase shift and a high level of integration due to its small size.

  13. Temperature effects in Au piezoresistors integrated in SU-8 cantilever chips

    DEFF Research Database (Denmark)

    Johansson, Alicia; Hansen, Ole; Hales, Jan Harry

    2006-01-01

    We present a cantilever-based biosensor chip made for the detection of biochemical molecules. The device is fabricated entirely in the photosensitive polymer SU-8 except for integrated piezoresistors made of Au. The integrated piezoresistors are used to monitor the surface stress changes due to b...

  14. Fabrication and characterization of microcavity lasers in rhodamine B doped SU8 using high energy proton beam

    Science.gov (United States)

    Venugopal Rao, S.; Bettiol, A. A.; Vishnubhatla, K. C.; Bhaktha, S. N. B.; Narayana Rao, D.; Watt, F.

    2007-03-01

    The authors present their results on the characterization of individual dye-doped microcavity polymer lasers fabricated using a high energy proton beam. The lasers were fabricated in rhodamine B doped SU8 resist with a single exposure step followed by chemical processing. The resulting trapezoidal shaped cavities had dimensions of ˜250×250μm2. Physical characterization of these structures was performed using a scanning electron microscope while the optical characterization was carried out by recording the emission subsequent to pumping the lasers with 532nm, 6 nanosecond pulses. The authors observed intense, narrow emission near 624nm with the best emission linewidth full width at half maximum of ˜9nm and a threshold ˜150μJ/mm2.

  15. SU-8 Lenses: Simple Methods of Fabrication and Application in Optical Interconnection Between Fiber/LED and Microstructures

    Science.gov (United States)

    Nguyen, Minh-Hang; Nguyen, Hai-Binh; Nguyen, Tuan-Hung; Vu, Xuan-Manh; Lai, Jain-Ren; Tseng, Fan-Gang; Chen, Te-Chang; Lee, Ming-Chang

    2016-05-01

    This paper presents two facile methods to fabricate off-plane lenses made of SU-8, an epoxy-based negative photoresist from MicroChem, on glass for optical interconnection. The methods allow the fabrication of lenses with flexible spot size and focal length depending on SU-8 well size and SU-8 drop volume and viscosity. In the first method, SU-8 drops were applied directly into patterned SU-8 wells with Teflon-coated micropipettes, and were baked to become (a)-spherical lenses. The lens shape and size were mainly determined by SU-8 viscosity, ratio of drop volume to well volume, and baking temperature and time. In the second method, a glass substrate with SU-8 patterned wells was emerged in diluted SU-8, then drawn up and baked to form lenses. The lens shapes and sizes were mainly determined by SU-8 viscosity and well volume. By the two methods, SU-8 lenses were successfully fabricated with spot sizes varying in range from micrometers to hundred micrometers, and focal lengths varying in range of several millimeters, depending on the lens rim diameters and aspheric sag height. Besides, on-plane SU-8 lenses were fabricated by photolithography to work in conjunction with the off-plane SU-8 lenses. The cascaded lenses produced light spots reduced to several micrometers, and they can be applied as a coupler for light coupling from fiber/Light-emitting diode (LED) to microstructures and nanostructures. The results open up the path for fabricating novel optical microsystems for optical communication and optical sensing applications.

  16. Simulation and experimental validation of a SU-8 based PCR thermocycler chip with integrated heaters and temperature sensor

    DEFF Research Database (Denmark)

    El-Ali, Jamil; Perch-Nielsen, Ivan R.; Poulsen, Claus Riber

    2004-01-01

    We present a SU-8 based polymerase chain reaction (PCR) chip with integrated platinum thin film heaters and temperature sensor. The device is fabricated in SU-8 on a glass substrate. The use of SU-8 provides a simple microfabrication process for the PCR chamber, controllable surface properties......C/s, respectively, the performance of the chip is comparable with the best silicon micromachined PCR chips presented in the literature. The SU-8 chamber surface was found to be PCR compatible by amplification of yeast gene ribosomal protein S3 and Campylobacter gene cadF. The PCR compatibility of the chamber...

  17. Experimental demonstration of an improved EPON architecture using OFDMA for bandwidth scalable LAN emulation

    DEFF Research Database (Denmark)

    Deng, Lei; Zhao, Ying; Yu, Xianbin

    2011-01-01

    We propose and demonstrate an improved Ethernet passive optical network (EPON) architecture supporting bandwidth-scalable physical layer local area network (LAN) emulation. Due to the use of orthogonal frequency division multiple access (OFDMA) technology for the LAN traffic transmission, there i...

  18. Biofriendly bonding processes for nanoporous implantable SU-8 microcapsules for encapsulated cell therapy.

    Science.gov (United States)

    Nemani, Krishnamurthy; Kwon, Joonbum; Trivedi, Krutarth; Hu, Walter; Lee, Jeong-Bong; Gimi, Barjor

    2011-01-01

    Mechanically robust, cell encapsulating microdevices fabricated using photolithographic methods can lead to more efficient immunoisolation in comparison to cell encapsulating hydrogels. There is a need to develop adhesive bonding methods which can seal such microdevices under physiologically friendly conditions. We report the bonding of SU-8 based substrates through (i) magnetic self assembly, (ii) using medical grade photocured adhesive and (iii) moisture and photochemical cured polymerization. Magnetic self-assembly, carried out in biofriendly aqueous buffers, provides weak bonding not suitable for long term applications. Moisture cured bonding of covalently modified SU-8 substrates, based on silanol condensation, resulted in weak and inconsistent bonding. Photocured bonding using a medical grade adhesive and of acrylate modified substrates provided stable bonding. Of the methods evaluated, photocured adhesion provided the strongest and most stable adhesion.

  19. Optimized plasma-deposited fluorocarbon coating for dry release and passivation of thin SU-8 cantilevers

    DEFF Research Database (Denmark)

    Keller, Stephan Urs; Häfliger, Daniel; Boisen, Anja

    2008-01-01

    during fluorocarbon deposition, the surface free energy of the coating can be tuned to allow for uniform wetting during spin coating of arbitrary thin SU-8 films. Further, they define an optimal pressure regime for the release of thin polymer structures at high yield. They demonstrate the successful......Plasma-deposited fluorocarbon coatings are introduced as a convenient method for the dry release of polymer structures. In this method, the passivation process in a deep reactive ion etch reactor was used to deposit hydrophobic fluorocarbon films. Standard photolithography with the negative epoxy......-based photoresist SU-8 was used to fabricate polymer structures such as cantilevers and membranes on top of the nonadhesive release layer. The authors identify the plasma density as the main parameter determining the surface properties of the deposited fluorocarbon films. They show that by modifying the pressure...

  20. Electromagnetic characterization of strontium ferrite powders in series 2000, SU8 polymer

    International Nuclear Information System (INIS)

    Sholiyi, Olusegun; Williams, John

    2014-01-01

    In this article, electromagnetic characterization of strontium hexaferrite powders and composites with SU8 was carried out to determine their compatibility with micro and millimeter wave fabrications. The structures of both powders and their composites were scanned with electron microscope to produce the SEM images. Two powder sizes (0.8–1.0 μm and 3–6 μm), were mixed with SU8, spin cast and patterned on wafer, and then characterized using energy dispersive x-ray spectrometry, ferromagnetic resonance (FMR) and vibrating sample magnetometry. In this investigation, FMRs of the samples were determined at 60 GHz while their complex permittivity and permeability were determined using rectangular waveguide method of characterization between 26.5 and 40 GHz frequency range. The results obtained show no adverse effects on the electromagnetic properties of the composites except some slight shift in the resonant frequencies due to anisotropic field of the samples. (paper)

  1. Drift study of SU8 cantilevers in liquid and gaseous environments.

    Science.gov (United States)

    Tenje, Maria; Keller, Stephan; Dohn, Søren; Davis, Zachary J; Boisen, Anja

    2010-05-01

    We present a study of the drift, in terms of cantilever deflections without probe/target interactions, of polymeric SU8 cantilevers. The drift is measured in PBS buffer (pH 7.4) and under vacuum (1mbar) conditions. We see that the cantilevers display a large drift in both environments. We believe this is because the polymer matrix absorbs liquid in one situation whereas it is being degassed in the other. An inhomogeneous expansion/contraction of the cantilever is seen because one surface of the cantilever may still have remains of the release layer from the fabrication. To further study the effect, we coat the cantilevers with a hydrophobic coating, perfluorodecyltrichlorosilane (FDTS). Fully encapsulating the SU8 cantilever greatly reduces the drift in liquid whereas a less significant change is seen in vacuum.

  2. Drift study of SU8 cantilevers in liquid and gaseous environments

    DEFF Research Database (Denmark)

    Tenje, Maria; Keller, Stephan Sylvest; Dohn, Søren

    2010-01-01

    We present a study of the drift, in terms of cantilever deflections without probe/target interactions, of polymeric SU8 cantilevers. The drift is measured in PBS buffer (pH 7.4) and under vacuum (1 mbar) conditions. We see that the cantilevers display a large drift in both environments. We believe...... coat the cantilevers with a hydrophobic coating, perfluorodecyltrichlorosilane (FDTS). Fully encapsulating the SU8 cantilever greatly reduces the drift in liquid whereas a less significant change is seen in vacuum....... this is because the polymer matrix absorbs liquid in one situation whereas it is being degassed in the other. An inhomogeneous expansion/contraction of the cantilever is seen because one surface of the cantilever may still have remains of the release layer from the fabrication. To further study the effect, we...

  3. Electromagnetic characterization of strontium ferrite powders in series 2000, SU8 polymer

    Science.gov (United States)

    Sholiyi, Olusegun; Williams, John

    2014-12-01

    In this article, electromagnetic characterization of strontium hexaferrite powders and composites with SU8 was carried out to determine their compatibility with micro and millimeter wave fabrications. The structures of both powders and their composites were scanned with electron microscope to produce the SEM images. Two powder sizes (0.8-1.0 μm and 3-6 μm), were mixed with SU8, spin cast and patterned on wafer, and then characterized using energy dispersive x-ray spectrometry, ferromagnetic resonance (FMR) and vibrating sample magnetometry. In this investigation, FMRs of the samples were determined at 60 GHz while their complex permittivity and permeability were determined using rectangular waveguide method of characterization between 26.5 and 40 GHz frequency range. The results obtained show no adverse effects on the electromagnetic properties of the composites except some slight shift in the resonant frequencies due to anisotropic field of the samples.

  4. Fabrication of thin SU-8 cantilevers: initial bending, release and time stability

    International Nuclear Information System (INIS)

    Keller, Stephan; Boisen, Anja; Haefliger, Daniel

    2010-01-01

    SU-8 cantilevers with a thickness of 2 µm were fabricated using a dry release method and two steps of SU-8 photolithography. The processing of the thin SU-8 film defining the cantilevers was experimentally optimized to achieve low initial bending due to residual stress gradients. In parallel, the rotational deformation at the clamping point allowed a qualitative assessment of the device release from the fluorocarbon-coated substrate. The change of these parameters during several months of storage at ambient temperature was investigated in detail. The introduction of a long hard bake in an oven after development of the thin SU-8 film resulted in reduced cantilever bending due to removal of residual stress gradients. Further, improved time-stability of the devices was achieved due to the enhanced cross-linking of the polymer. A post-exposure bake at a temperature T PEB = 50 °C followed by a hard bake at T HB = 90 °C proved to be optimal to ensure low cantilever bending and low rotational deformation due to excellent device release and low change of these properties with time. With the optimized process, the reproducible fabrication of arrays with 2 µm thick cantilevers with a length of 500 µm and an initial bending of less than 20 µm was possible. The theoretical spring constant of these cantilevers is k = 4.8 ± 2.5 mN m −1 , which is comparable to the value for Si cantilevers with identical dimensions and a thickness of 500 nm.

  5. Hydrophobic coating of microfluidic chips structured by SU-8 polymer for segmented flow operation

    International Nuclear Information System (INIS)

    Schumacher, J T; Grodrian, A; Metze, J; Kremin, C; Hoffmann, M

    2008-01-01

    We present a hydrophobization procedure for SU-8-based microfluidic chips on borofloat substrates. Different layouts of gold electrodes passivated by the polymer have been investigated. The chips are used for segmented flow in a two-fluid mode that requires a distinct hydrophobicity of the channel walls which is generated by the use of specific silane. In this paper we describe the production and silanization of the chips and demonstrate segmented flow operation

  6. Silicon/SU8 multi-electrode micro-needle for in vivo neurochemical monitoring.

    Science.gov (United States)

    Vasylieva, Natalia; Marinesco, Stéphane; Barbier, Daniel; Sabac, Andrei

    2015-10-15

    Simultaneous monitoring of glucose and lactate is an important challenge for understanding brain energetics in physiological or pathological states. We demonstrate here a versatile method based on a minimally invasive single implantation in the rat brain. A silicon/SU8-polymer multi-sensing needle-shaped biosensor, was fabricated and tested. The multi-electrode array design comprises three platinum planar microelectrodes with a surface area of 40 × 200 µm(2) and a spacing of 200 µm, which were micromachined on a single 3mm long micro-needle having a 100 × 50 µm(2) cross-section for reduced tissue damage during implantation. Platinum micro-electrodes were aligned at the bottom of micro-wells obtained by photolithography on a SU8 photoresist layer. After clean room processing, each micro-electrode was functionalized inside the micro-wells by means of a micro-dispensing device, either with glucose oxidase or with lactate oxidase, which were cross-linked on the platinum electrodes. The third electrode covered with Bovine Serum Albumin (BSA) was used for the control of non-specific currents. The thick SU8 photoresist layer has revealed excellent electrical insulation of the micro-electrodes and between interconnection lines, and ensured a precise localization and packaging of the sensing enzymes on platinum micro-electrodes. During in vitro calibration with concentrations of analytes in the mM range, the micro-wells patterned in the SU8 photoresist proved to be highly effective in eliminating cross-talk signals, caused by H2O2 diffusion from closely spaced micro-electrodes. Moreover, our biosensor was successfully assayed in the rat cortex for simultaneous monitoring of both glucose and lactate during insulin and glucose administration. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Refractive index modulation of SU-8 polymer optical waveguides by means of hybrid photothermal process

    OpenAIRE

    Salazar-Miranda, D.; Castillón, F. F.; Sánchez-Sánchez, J. J.; Angel-Valenzuela, J. L.; Márquez, H.

    2010-01-01

    This paper describes the fabrication and characterization of multimode polymer optical waveguides obtained using a SU-8-2005 polymer by means of photolithographic process. Critical information about refractive index modulation of polymer waveguides as function of fabrication parameters as pre-baked and ultraviolet exposure times is presented. Physical properties of the waveguides were determined by means prism-coupling technique, optical and SEM microscopy. Este trabajo describe la fabrica...

  8. Performance of SU-8 Membrane Suitable for Deep X-Ray Grayscale Lithography

    Directory of Open Access Journals (Sweden)

    Harutaka Mekaru

    2015-02-01

    Full Text Available In combination with tapered-trench-etching of Si and SU-8 photoresist, a grayscale mask for deep X-ray lithography was fabricated and passed a 10-times-exposure test. The performance of the X-ray grayscale mask was evaluated using the TERAS synchrotron radiation facility at the National Institute of Advanced Industrial Science and Technology (AIST. Although the SU-8 before photo-curing has been evaluated as a negative-tone photoresist for ultraviolet (UV and X-ray lithographies, the characteristic of the SU-8 after photo-curing has not been investigated. A polymethyl methacrylate (PMMA sheet was irradiated by a synchrotron radiation through an X-ray mask, and relationships between the dose energy and exposure depth, and between the dose energy and dimensional transition, were investigated. Using such a technique, the shape of a 26-μm-high Si absorber was transformed into the shape of a PMMA microneedle with a height of 76 μm, and done with a high contrast. Although during the fabrication process of the X-ray mask a 100-μm-pattern-pitch (by design was enlarged to 120 μm. However, with an increase in an integrated dose energy this number decreased to 99 μm. These results show that the X-ray grayscale mask has many practical applications. In this paper, the author reports on the evaluation results of SU-8 when used as a membrane material for an X-ray mask.

  9. SU-8 based microdevices to study self-induced chemotaxis in 3D microenvironments

    Science.gov (United States)

    Ayuso, Jose; Monge, Rosa; Llamazares, Guillermo; Moreno, Marco; Agirregabiria, Maria; Berganzo, Javier; Doblaré, Manuel; Ochoa, Iñaki; Fernandez, Luis

    2015-05-01

    Tissues are complex three-dimensional structures in which cell behaviour is frequently guided by chemotactic signals. Although starvation and nutrient restriction induce many different chemotactic processes, the recreation of such conditions in vitro remains difficult when using standard cell culture equipment. Recently, microfluidic techniques have arisen as powerful tools to mimic such physiological conditions. In this context, microfluidic three-dimensional cell culture systems require precise control of cell/hydrogel location because samples need to be placed within a microchamber without obstruction of surrounding elements. In this article, SU-8 is studied as structural material for the fabrication of complex cell culture devices due to its good mechanical properties, low gas permeability and sensor integration capacity. In particular, this manuscript presents a SU-8 based microdevice designed to create “self-induced” medium starvation, based on the combination of nutrient restriction and natural cell metabolism. Results show a natural migratory response towards nutrient source, showing how cells adapt to their own microenvironment modifications. The presented results demonstrate the SU-8 potential for microdevice fabrication applied to cell culture.

  10. Micro-scale metallization on flexible polyimide substrate by Cu electroplating using SU-8 photoresist mask

    International Nuclear Information System (INIS)

    Cho, S.H.; Kim, S.H.; Lee, N.-E.; Kim, H.M.; Nam, Y.W.

    2005-01-01

    Technologies for flexible electronics have been developed to make electronic or microelectromechanical (MEMS) devices on inexpensive and flexible organic substrates. In order to fabricate the interconnect lines between device elements or layers in flexible electronic devices, metallization on the flexible substrate is essential. In this case, the width and conductivity of metallization line are very important for minimizing the size of device. Therefore, the realization of metallization process with the scale of a few micrometers on the flexible substrate is required. In this work, micro-scale metallization lines of Cu were fabricated on the flexible substrate by electroplating using the patterned mask of a negative-tone SU-8 photoresist. Polyimide surface was treated by O 2 /Ar atmospheric plasma for the improvement in adhesion between Cr layer and polyimide and in situ sputter deposition of 100-nm-thick Cu seed layers on the sputter-deposited 50-nm-thick Cr adhesion layer was followed. SU-8 photoresist was spin-coated and patterned by photolithography. Electroplating of Cu line, removal of SU-8, and selective wet etch of Cr adhesion and Cu seed layers were carried out. Gap between the Cu lines was successfully filled by spin-coating of polyimide. Micro-scale Cu metal lines with gap filling on the polyimide substrate with a thickness of 6-12 μm and an aspect ratio of 1-3 were successfully fabricated

  11. Direct injection in organic SU8 nanowires and nanotubes for waveguiding properties investigation

    Science.gov (United States)

    Bigeon, J.; Huby, N.; Duvail, Jean-Luc; Bêche, Bruno

    2014-05-01

    We report photonic concepts related to injection and sub-wavelength propagation in nanofibers (nanowires and nanotubes). These nanostructures are fabricated by the wetting template method leading to aspect ratio of over 250. At first, injection into nanowires and nanotubes of SU8, a photoresist used for integrated photonics, was successfully achieved by using polymer microlensed fibers with sub-micronic radius of curvature. Theoret- ical simulation by finite domain time-dependent (FDTD) method was used to determine the sub-wavelength propagation for nanowires and nanotubes and corroborate this coupling phenomena. The original confinement of energy density into SU8 nanotubes is highlighted. Finally, characterisation of propagation losses is reported by using a cut-back method transposed to such nanotubes and determined to range between 1 and 2 dB/mm. Both injection and cut-back method developed here are compatible with any sub-micronic structures. This work on SU8 nanofibers suggests broader perspectives for future nanophotonics.

  12. SU-8 cantilevers for bio/chemical sensing; Fabrication, characterisation and development of novel read-out methods

    DEFF Research Database (Denmark)

    Nordström, M.; Keller, Stephan Urs; Lillemose, Michael

    2008-01-01

    Here, we present the activities within our research group over the last five years with cantilevers fabricated in the polymer SU-8. We believe that SU-8 is an interesting polymer for fabrication of cantilevers for bio/chemical sensing due to its simple processing and low Young's modulus. We show...

  13. PMMA to SU-8 bonding for polymer based lab-on-a-chip systems with integrated optics

    DEFF Research Database (Denmark)

    Olsen, Brian Bilenberg; Nielsen, Theodor; Clausen, Bjarne Hans

    2004-01-01

    We present an adhesive bonding technique developed for SU-8 based "lab-on-a-chip"- systems with integrated optical components. Microfluidic channels and optical components (e.g. wave-guides) are defined in SU-8 photoresist on a Pyrex glass substrate. The microfluidic channels are sealed by a second...... Pyrex substrate, bonded on top of the cross-linked SU-8 structure using an inter- mediate layer of 950K molecular weight poly-methylmethacrylate (PMMA). Due to a lower refractive index of PMMA, this bonding technique offers optical waveguiding in the SU-8 structures in combination with good sealing...... of the microfluidic channels. The bonding technique is investigated with respect to bonding temperature in the range of 50 - 150 degr. C and at bonding forces of 1000 N and 2000 N on a 4-inch wafer. A maximum bonding strength of 16 MPa is achieved for the PMMA to SU-8 bonding at a bonding temperature of 110 degr. C...

  14. Optimized piranha etching process for SU8-based MEMS and MOEMS construction

    International Nuclear Information System (INIS)

    Holmes, Matthew; Keeley, Jared; Hurd, Katherine; Hawkins, Aaron; Schmidt, Holger

    2010-01-01

    We demonstrate the optimization of the concentration, temperature and cycling of a piranha (H 2 O 2 :H 2 SO 4 ) mixture that produces high yields while quickly etching hollow structures made using a highly crosslinked SU8 polymer sacrificial core. The effects of the piranha mixture on the thickness, refractive index and roughness of common micro-electromechanical systems and micro-opto-electromechanical systems fabrication materials (SiN, SiO 2 and Si) were determined. The effectiveness of the optimal piranha mixture was demonstrated in the construction of hollow anti-resonant reflecting optical waveguides

  15. Optimized piranha etching process for SU8-based MEMS and MOEMS construction

    Science.gov (United States)

    Holmes, Matthew; Keeley, Jared; Hurd, Katherine; Schmidt, Holger; Hawkins, Aaron

    2010-11-01

    We demonstrate the optimization of the concentration, temperature and cycling of a piranha (H2O2:H2SO4) mixture that produces high yields while quickly etching hollow structures made using a highly crosslinked SU8 polymer sacrificial core. The effects of the piranha mixture on the thickness, refractive index and roughness of common micro-electromechanical systems and micro-opto-electromechanical systems fabrication materials (SiN, SiO2 and Si) were determined. The effectiveness of the optimal piranha mixture was demonstrated in the construction of hollow anti-resonant reflecting optical waveguides.

  16. Large-core single-mode rib SU8 waveguide using solvent-assisted microcontact molding.

    Science.gov (United States)

    Huang, Cheng-Sheng; Wang, Wei-Chih

    2008-09-01

    This paper describes a novel fabrication technique for constructing a polymer-based large-core single-mode rib waveguide. A negative tone SU8 photoresist with a high optical transmission over a large wavelength range and stable mechanical properties was used as a waveguide material. A waveguide was constructed by using a polydimethylsiloxane stamp combined with a solvent-assisted microcontact molding technique. The effects on the final pattern's geometry of four different process conditions were investigated. Optical simulations were performed using beam propagation method software. Single-mode beam propagation was observed at the output of the simulated waveguide as well as the actual waveguide through the microscope image.

  17. Optimized piranha etching process for SU8-based MEMS and MOEMS construction

    OpenAIRE

    Holmes, Matthew; Keeley, Jared; Hurd, Katherine; Schmidt, Holger; Hawkins, Aaron

    2010-01-01

    We demonstrate the optimization of the concentration, temperature and cycling of a piranha (H2O2:H2SO4) mixture that produces high yields while quickly etching hollow structures made using a highly crosslinked SU8 polymer sacrificial core. The effects of the piranha mixture on the thickness, refractive index and roughness of common micro-electromechanical systems and micro-opto-electromechanical systems fabrication materials (SiN, SiO2 and Si) were determined. The effectiveness of the optimal...

  18. Microfabrication of pre-aligned fiber bundle couplers using ultraviolet lithography of SU-8

    OpenAIRE

    Yang, Ren; Soper, Steven A.; Wang, Wanjun

    2006-01-01

    This paper describes the design, microfabrication and testing of a pre-aligned array of fiber couplers using direct UV-lithography of SU-8. The fiber coupler array includes an out-of-plane refractive microlens array and two fiberport collimator arrays. With the optical axis of the pixels parallel to the substrate, each pixel of the microlens array can be pre-aligned with the corresponding pixels of the fiberport collimator array as defined by the lithography mask design. This out-of-plane pol...

  19. SU-8 Cantilevers for Bio/chemical Sensing; Fabrication, Characterisation and Development of Novel Read-out Methods

    OpenAIRE

    Anja Boisen; Mogens Havsteen-Jakobsen; Gabriela Blagoi; Daniel Haefliger; Søren Dohn; Alicia Johansson; Michael Lillemose; Stephan Keller; Maria Nordström

    2008-01-01

    Here, we present the activities within our research group over the last five years with cantilevers fabricated in the polymer SU-8. We believe that SU-8 is an interesting polymer for fabrication of cantilevers for bio/chemical sensing due to its simple processing and low Young's modulus. We show examples of different integrated read-out methods and their characterisation. We also show that SU-8 cantilevers have a reduced sensitivity to changes in the environmental temperature and pH of the bu...

  20. Analysis of Sleep-Mode Downlink Scheduling Operations in EPON Systems

    OpenAIRE

    Yan, Ying; Dittmann, Lars

    2011-01-01

    Energy management strategy has been considered as an important component in the future Ethernet Passive Optical Networks (EPONs). In this paper, a sleeping mode operation is studied, and a downlink packet scheduling scheme is analyzed to preserve energy consumption and maintain the required QoS. This paper proposes a novel sleep-mode downlink packet scheduling scheme in order to enhance the sleep control function. Simulation results confirm that the proposed approach offers effective power ma...

  1. Effect of size and moisture on the mechanical behavior of SU-8 thin films

    Science.gov (United States)

    Robin, C. J.; Jonnalagadda, K. N.

    2016-02-01

    The mechanical properties of SU-8 were investigated in conjunction with size effect, mechanical anisotropy and moisture absorption. Uniaxial tensile experiments were conducted on SU-8 films of 500 nm and 2 μm thickness. A spin coating process was used to fabricate the films with one set from a single coat (single layer) and the others containing multiple coats (multilayer) with pre-baking in between. The stress versus strain response was obtained from in situ optical experiments and a digital image correlation method. Compared to single layer films, the multilayer films showed a significant increase in mechanical properties as well as in-plane anisotropy. This anisotropy was confirmed using Fourier transform infrared spectroscopy and attributed to the spin coating process, which resulted in higher crosslinking density in the film, and molecular orientation in the radial direction. Moisture absorption studies revealed that the mechanical properties were affected by water, which exists in both the free and bonded form in the polymer and acts as a plasticizer. The effect of moisture was similar in both the single and multilayer films, but was higher for the latter due to multiple processing steps as well as the existence of higher percentage of epoxy polar groups.

  2. Influences of pretreatment and hard baking on the mechanical reliability of SU-8 microstructures

    International Nuclear Information System (INIS)

    Morikaku, Toshiyuki; Kaibara, Yoshinori; Inoue, Shozo; Namazu, Takahiro; Inoue, Masatoshi; Miura, Takuya; Suzuki, Takaaki; Oohira, Fumikazu

    2013-01-01

    In this paper, the influences of pretreatment and hard baking on the mechanical characteristics of SU-8 microstructures are described. Four types of samples with different combinations of O 2 plasma ashing, primer coating and hard baking were prepared for shear strength tests and uniaxial tensile tests. Specially developed shear test equipment was used to experimentally measure the shear adhesion strength of SU-8 micro posts on a glass substrate. The adhesiveness was strengthened by hard baking at 200 °C for 60 min, whereas other pretreatment processes hardly affected the strength. The pretreatment and hard baking effects on the adhesive strength were compared with those on the fracture strength measured by uniaxial tensile testing. There were no influences of O 2 plasma ashing on both the strengths, and primer coating affected only tensile strength. The primer coating effect as well as the hard baking effect on stress relaxation phenomena in uniaxial tension was observed as well. Fourier transform infrared spectroscopy demonstrated that surface degradation and epoxide-ring opening polymerization would have given rise to the primer coating effect and the hard baking effect on the mechanical characteristics, respectively. (paper)

  3. Influences of pretreatment and hard baking on the mechanical reliability of SU-8 microstructures

    Science.gov (United States)

    Morikaku, Toshiyuki; Kaibara, Yoshinori; Inoue, Masatoshi; Miura, Takuya; Suzuki, Takaaki; Oohira, Fumikazu; Inoue, Shozo; Namazu, Takahiro

    2013-10-01

    In this paper, the influences of pretreatment and hard baking on the mechanical characteristics of SU-8 microstructures are described. Four types of samples with different combinations of O2 plasma ashing, primer coating and hard baking were prepared for shear strength tests and uniaxial tensile tests. Specially developed shear test equipment was used to experimentally measure the shear adhesion strength of SU-8 micro posts on a glass substrate. The adhesiveness was strengthened by hard baking at 200 °C for 60 min, whereas other pretreatment processes hardly affected the strength. The pretreatment and hard baking effects on the adhesive strength were compared with those on the fracture strength measured by uniaxial tensile testing. There were no influences of O2 plasma ashing on both the strengths, and primer coating affected only tensile strength. The primer coating effect as well as the hard baking effect on stress relaxation phenomena in uniaxial tension was observed as well. Fourier transform infrared spectroscopy demonstrated that surface degradation and epoxide-ring opening polymerization would have given rise to the primer coating effect and the hard baking effect on the mechanical characteristics, respectively.

  4. Effect of size and moisture on the mechanical behavior of SU-8 thin films

    International Nuclear Information System (INIS)

    Robin, C J; Jonnalagadda, K N

    2016-01-01

    The mechanical properties of SU-8 were investigated in conjunction with size effect, mechanical anisotropy and moisture absorption. Uniaxial tensile experiments were conducted on SU-8 films of 500 nm and 2 μm thickness. A spin coating process was used to fabricate the films with one set from a single coat (single layer) and the others containing multiple coats (multilayer) with pre-baking in between. The stress versus strain response was obtained from in situ optical experiments and a digital image correlation method. Compared to single layer films, the multilayer films showed a significant increase in mechanical properties as well as in-plane anisotropy. This anisotropy was confirmed using Fourier transform infrared spectroscopy and attributed to the spin coating process, which resulted in higher crosslinking density in the film, and molecular orientation in the radial direction. Moisture absorption studies revealed that the mechanical properties were affected by water, which exists in both the free and bonded form in the polymer and acts as a plasticizer. The effect of moisture was similar in both the single and multilayer films, but was higher for the latter due to multiple processing steps as well as the existence of higher percentage of epoxy polar groups. (paper)

  5. Inkjet Printing of High Aspect Ratio Superparamagnetic SU-8 Microstructures with Preferential Magnetic Directions

    Directory of Open Access Journals (Sweden)

    Loïc Jacot-Descombes

    2014-08-01

    Full Text Available Structuring SU-8 based superparamagnetic polymer composite (SPMPC containing Fe3O4 nanoparticles by photolithography is limited in thickness due to light absorption by the nanoparticles. Hence, obtaining thicker structures requires alternative processing techniques. This paper presents a method based on inkjet printing and thermal curing for the fabrication of much thicker hemispherical microstructures of SPMPC. The microstructures are fabricated by inkjet printing the nanoparticle-doped SU-8 onto flat substrates functionalized to reduce the surface energy and thus the wetting. The thickness and the aspect ratio of the printed structures are further increased by printing the composite onto substrates with confinement pedestals. Fully crosslinked microstructures with a thickness up to 88.8 μm and edge angle of 112° ± 4° are obtained. Manipulation of the microstructures by an external field is enabled by creating lines of densely aggregated nanoparticles inside the composite. To this end, the printed microstructures are placed within an external magnetic field directly before crosslinking inducing the aggregation of dense Fe3O4 nanoparticle lines with in-plane and out-of-plane directions.

  6. Dielectric properties of ligand-modified gold nanoparticle/SU-8 photopolymer based nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Toor, Anju, E-mail: atoor@berkeley.edu [Department of Mechanical Engineering, University of California, Berkeley, CA 94720 (United States); So, Hongyun, E-mail: hyso@berkeley.edu [Department of Mechanical Engineering, University of California, Berkeley, CA 94720 (United States); Pisano, Albert P. [Department of Mechanical Engineering, University of California, Berkeley, CA 94720 (United States); Department of Mechanical and Aerospace Engineering, University of California, San Diego, CA 92093 (United States)

    2017-08-31

    Highlights: • Ligand-modified gold NP/SU-8 nanocomposites were synthesized and demonstrated. • Particle agglomeration and dispersion were characterized with different NPs concentration. • Nanocomposites showed higher average dielectric permittivity compared to SU-8 only. • Relatively lower dielectric loss (average 0.09 at 1 kHz) was achieved with 10 % w/w NPs. - Abstract: This article reports the enhanced dielectric properties of a photodefinable polymer nanocomposite material containing sub–10 nm coated metal nanoparticles (NPs). The surface morphology of the synthesized dodecanethiol-functionalized gold NPs was characterized using the transmission electron microscopy (TEM). We investigated the particle agglomeration and dispersion during the various stages of the nanocomposite synthesis using TEM. Physical properties such as dielectric permittivity and dielectric loss were measured experimentally. The dependence of the dielectric permittivity and loss tangent on the particle concentration, and frequency was studied. Nanocomposite films showed an approximately three times enhancement in average dielectric constant over the polymer base value and an average dielectric loss of 0.09 at 1 kHz, at a filler loading of 10% w/w.

  7. PMMA to SU-8 Bonding for Polymer Based Lab-on-a-chip Systems with Integrated Optics

    DEFF Research Database (Denmark)

    Olsen, Brian Bilenberg; Nielsen, Theodor; Nilsson, Daniel

    2003-01-01

    An adhesive bonding technique for wafer-level sealing of SU-8 based lab-on-a-chip microsystems with integrated optical components is presented. Microfluidic channels and optical components, e.g. waveguides, are fabricated in cross-linked SU-8 and sealed with a Pyrex glass substrate by means...... strength of 16 MPa is achieved at bonding temperatures between 110 oC and 120oC, at a bonding force of 2000 N on a 4-inch wafer. The optical propagation loss of multi-mode 10ym (thickness)x 30ym (width)SU-8 waveguides is measured. The propagation loss in PMMA bonded waveguide struc-tures is more than 5 d......B/cm lower, at wavelengths between 600nm and 900 nm, than in similar structures bonded by an intermediate layer of SU-8. Furthermore 950K PMMA shows no tendency to flow into the bonded structures during bonding because of its high viscosity....

  8. SU-8 Cantilevers for Bio/chemical Sensing; Fabrication, Characterisation and Development of Novel Read-out Methods

    Directory of Open Access Journals (Sweden)

    Anja Boisen

    2008-03-01

    Full Text Available Here, we present the activities within our research group over the last five yearswith cantilevers fabricated in the polymer SU-8. We believe that SU-8 is an interestingpolymer for fabrication of cantilevers for bio/chemical sensing due to its simple processingand low Young’s modulus. We show examples of different integrated read-out methodsand their characterisation. We also show that SU-8 cantilevers have a reduced sensitivity tochanges in the environmental temperature and pH of the buffer solution. Moreover, weshow that the SU-8 cantilever surface can be functionalised directly with receptormolecules for analyte detection, thereby avoiding gold-thiol chemistry.

  9. A two-step sealing-and-reinforcement SU8 bonding paradigm for the fabrication of shallow microchannels

    Science.gov (United States)

    Mehboudi, Aryan; Yeom, Junghoon

    2018-03-01

    Adhesive bonding is a key technique to create microfluidic devices when two separate substrates are used to form microchannels. Among many adhesives explored in microchannel fabrication, SU8 has been widely used as an adhesive layer for sealing the microchannel sidewalls. The majority of the available SU8-based bonding methods, however, suffer from the difficulties associated with sealing of two important types of the microchannel architecture: (1) shallow microchannels with small patterns on a large area, and (2) microchannels with ultra-low aspect ratios (e.g. 6 mm in width and 2~μ m in height). In this paper, a new bonding paradigm based upon the low-temperature and low-pressure SU8 bonding, consisting of two steps of sealing using a thin-SU8-coated PET film and bonding reinforcement using a SU8-coated glass slide, is proposed to resolve the aforementioned difficulties. Since it does not need complicated instruments such as a wafer bonding machine and a lamination device, the developed bonding paradigm is convenient and economical. We successfully demonstrate the compatibility of the proposed bonding paradigm with the two microchannel fabrication approaches based on the glass wet etching and the SU8 photo-lithography, where small microchannels with the innermost surfaces fully made of SU8 are obtained. A theoretical model is employed to better investigate the flow characteristics and the structural behavior of the microchannel including the PET film deformation, strain and von Mises stress distributions, bonding strength, etc. Moreover, we demonstrate the fabrication of the multi-height deep-shallow microchannel sidewalls and their sealing using the SU8-coated PET film. Finally, as a proof-of-concept device, a microfluidic filter consisting of the double-height deep-shallow microchannel is fabricated for separation of 3 µm and 10 µm particles.

  10. A new fabrication process for uniform SU-8 thick photoresist structures by simultaneously removing edge bead and air bubbles

    International Nuclear Information System (INIS)

    Lee, Hun; Lee, Kangsun; Ahn, Byungwook; Xu, Jing; Xu, Linfeng; Oh, Kwang W

    2011-01-01

    This paper proposes a new SU-8 fabrication process to simultaneously remove edge bead and tiny air bubbles by spraying out edge bead removal (EBR) fluid over the entire surface of photoresist. In particular, the edge bead and air bubbles can cause an air gap between a film mask and a photoresist surface during UV exposure. The diffraction effect of UV light by the air gap leads to inaccurate and non-uniform SU-8 patterns. In this study, we demonstrate a simple method using EBR treatment to simultaneously eliminate the edge bead at the edge of wafer and tiny air bubbles inside SU-8. The profiles of thickness variation of SU-8 films with/without the EBR treatment are measured. The results show that the proposed EBR treatment can successfully remove the edge bead and air bubbles over the entire SU-8 films. The average pattern uniformity of SU-8 is improved from 50.5% to 11.3% in the case of 200 µm thickness. This method is simple and inexpensive, compared to a standard EBR process, because it does not require specialized equipment and it can be applied regardless of substrate geometry (e.g. circular wafer and rectangular slide glass).

  11. Simulation of a low frequency Z-axis SU-8 accelerometer in coventorware and MEMS+

    KAUST Repository

    Carreno, Armando Arpys Arevalo

    2013-04-01

    This paper presents the simulation of a z-axis SU-8 capacitive accelerometer. The study consists of a modal analysis of the modeled accelerometer, a study relating capacitance to acceleration, capacitance to deflection, an effective spring constant calculation, and a comparison of results achieved using CoventorWare® ANALYZER™ and MEMS+®. A fabricated energy harvester design from [1] was used for modeling and simulation in this study, with a four spring attachment of a 650μm×650μm; ×110μm proof mass of 4.542×10-8 kg. At rest, the spacing between electrodes is 4μm along the z-axis, and at 1.5g acceleration, there is 1.9μm spacing between electrodes, at which point pull in occurs for a 1V voltage. © 2013 IEEE.

  12. A superhydrophobic chip based on SU-8 photoresist pillars suspended on a silicon nitride membrane

    KAUST Repository

    Marinaro, Giovanni; Accardo, Angelo; De Angelis, Francesco; Dane, Thomas; Weinhausen, Britta; Burghammer, Manfred; Riekel, Christian

    2014-01-01

    We developed a new generation of superhydrophobic chips optimized for probing ultrasmall sample quantities by X-ray scattering and fluorescence techniques. The chips are based on thin Si3N4 membranes with a tailored pattern of SU-8 photoresist pillars. Indeed, aqueous solution droplets can be evaporated and concentrated at predefined positions using a non-periodic pillar pattern. We demonstrated quantitatively the deposition and aggregation of gold glyconanoparticles from the evaporation of a nanomolar droplet in a small spot by raster X-ray nanofluorescence. Further, raster nanocrystallography of biological objects such as rod-like tobacco mosaic virus nanoparticles reveals crystalline macro-domain formation composed of highly oriented nanorods. © 2014 the Partner Organisations.

  13. A superhydrophobic chip based on SU-8 photoresist pillars suspended on a silicon nitride membrane

    KAUST Repository

    Marinaro, Giovanni

    2014-07-28

    We developed a new generation of superhydrophobic chips optimized for probing ultrasmall sample quantities by X-ray scattering and fluorescence techniques. The chips are based on thin Si3N4 membranes with a tailored pattern of SU-8 photoresist pillars. Indeed, aqueous solution droplets can be evaporated and concentrated at predefined positions using a non-periodic pillar pattern. We demonstrated quantitatively the deposition and aggregation of gold glyconanoparticles from the evaporation of a nanomolar droplet in a small spot by raster X-ray nanofluorescence. Further, raster nanocrystallography of biological objects such as rod-like tobacco mosaic virus nanoparticles reveals crystalline macro-domain formation composed of highly oriented nanorods. © 2014 the Partner Organisations.

  14. Bi-directional triplexer with butterfly MMI coupler using SU-8 polymer waveguides

    Science.gov (United States)

    Mareš, David; Jeřábek, Vítězslav; Prajzler, Václav

    2015-01-01

    We report about a design of a bi-directional planar optical multiplex/demultiplex filter (triplexer) for the optical part of planar hybrid WDM bi-directional transceiver in fiber-to-the-home (FTTH) PON applications. The triplex lightwave circuit is based on the Epoxy Novolak Resin SU-8 waveguides on the silica-on-silicon substrate with Polymethylmethacrylate cladding layer. The triplexer is comprised of a linear butterfly concept of multimode interference (MMI) coupler separating downstream optical signals of 1490 nm and 1550 nm. For the upstream channel of 1310 nm, an additional directional coupler (DC) is used to add optical signal of 1310 nm propagating in opposite direction. The optical triplexer was designed and optimized using beam propagation method. The insertion losses, crosstalk attenuation, and extinction ratio for all three inputs/outputs were investigated. The intended triplexer was designed using the parameters of the separated DC and MMI filter to approximate the idealized direct connection of both devices.

  15. The Morphology of Silver Layers on SU8 polymers prepared by Electroless Deposition

    Science.gov (United States)

    Dutta, Aniruddha; Yuan, Biao; Heinrich, Helge; Grabill, Chris; Williams, Henry; Kuebler, Stephen; Bhattacharya, Aniket

    2010-03-01

    Silver was deposited onto the functionalized surface of polymeric SU-8 where gold nanoparticles (Au-NPs) act as nucleation sites using electroless metallization chemistry. Here we report on the evolution of the nanoscale morphology of deposited Ag studied by Transmission Electron Microscopy (TEM). In TEM of sample cross sections correlations between the original gold and the silver nanoparticles were obtained while plan-view TEM results showed the distribution of nanoparticles on the surface. Scanning TEM with a high-angle annular dark field detector was used to obtain atomic number contrast. The morphology of the deposited Ag was controlled through the presence and absence of gum Arabic. The thickness and height fluctuations of the Ag layer were determined as a function of time and a statistical analysis of the growth process was conducted for the initial deposition periods.

  16. A novel and simple fabrication method of embedded SU-8 micro channels by direct UV lithography

    International Nuclear Information System (INIS)

    Fu, C; Hung, C; Huang, H

    2006-01-01

    In this paper, we presents a novel and simple method to fabricate embedded micro channels. The method based on different light absorption properties of the SU-8 thick photoresist under different incident UV wavelengths. The channel structures are defined by the ordinary I-line, while the cover layer is patterned by the deep UV. Because the deep UV is obtained directly on the same aligner with a set of filter mirrors, the embedded channel can be easily produced without other rare facilities. Besides, the relationship between the thickness of the top layer and the exposure dose of the deep UV has been measured by an ingeniously designed experiment. The specific thickness of the top layer of the embedded micro channel can then be secured by the specific deep-UV exposure dose. Further more, many meaningful mechanical structures have been realized by this method, the material property of the top layer are also measured

  17. SU-8 Based MEMS Process with Two Metal Layers using α-Si as a Sacrificial Material

    KAUST Repository

    Ramadan, Khaled S.

    2012-04-01

    Polymer based microelectromechanical systems (MEMS) micromachining is finding more interest in research and applications. This is due to its low cost and less time processing compared with silicon MEMS. SU-8 is a photo-patternable polymer that is used as a structural layer for MEMS and microfluidic devices. In addition to being processed with low cost, it is a biocompatible material with good mechanical properties. Also, amorphous silicon (α-Si) has found use as a sacrificial layer in silicon MEMS applications. α-Si can be deposited at large thicknesses for MEMS applications and also can be released in a dry method using XeF2 which can solve stiction problems related to MEMS applications. In this thesis, an SU-8 MEMS process is developed using amorphous silicon (α-Si) as a sacrificial layer. Electrostatic actuation and sensing is used in many MEMS applications. SU-8 is a dielectric material which limits its direct use in electrostatic actuation. This thesis provides a MEMS process with two conductive metal electrodes that can be used for out-of-plane electrostatic applications like MEMS switches and variable capacitors. The process provides the fabrication of dimples that can be conductive or non-conductive to facilitate more flexibility for MEMS designers. This SU-8 process can fabricate SU-8 MEMS structures of a single layer of two different thicknesses. Process parameters were tuned for two sets of thicknesses which are thin (5-10μm) and thick (130μm). Chevron bent-beam structures and different suspended beams (cantilevers and bridges) were fabricated to characterize the SU-8 process through extracting the density, Young’s Modulus and the Coefficient of Thermal Expansion (CTE) of SU-8. Also, the process was tested and used as an educational tool through which different MEMS structures were fabricated including MEMS switches, variable capacitors and thermal actuators.

  18. Development of an SU-8 MEMS process with two metal electrodes using amorphous silicon as a sacrificial material

    KAUST Repository

    Ramadan, Khaled S.

    2013-02-08

    This work presents an SU-8 surface micromachining process using amorphous silicon as a sacrificial material, which also incorporates two metal layers for electrical excitation. SU-8 is a photo-patternable polymer that is used as a structural layer for MEMS and microfluidic applications due to its mechanical properties, biocompatibility and low cost. Amorphous silicon is used as a sacrificial layer in MEMS applications because it can be deposited in large thicknesses, and can be released in a dry method using XeF2, which alleviates release-based stiction problems related to MEMS applications. In this work, an SU-8 MEMS process was developed using ;-Si as a sacrificial layer. Two conductive metal electrodes were integrated in this process to allow out-of-plane electrostatic actuation for applications like MEMS switches and variable capacitors. In order to facilitate more flexibility for MEMS designers, the process can fabricate dimples that can be conductive or nonconductive. Additionally, this SU-8 process can fabricate SU-8 MEMS structures of a single layer of two different thicknesses. Process parameters were optimized for two sets of thicknesses: thin (5-10 m) and thick (130 m). The process was tested fabricating MEMS switches, capacitors and thermal actuators. © 2013 IOP Publishing Ltd.

  19. Modeling and Simulation of Handover Scheme in Integrated EPON-WiMAX Networks

    DEFF Research Database (Denmark)

    Yan, Ying; Dittmann, Lars

    2011-01-01

    In this paper, we tackle the seamless handover problem in integrated optical wireless networks. Our model applies for the convergence network of EPON and WiMAX and a mobilityaware signaling protocol is proposed. The proposed handover scheme, Integrated Mobility Management Scheme (IMMS), is assisted...... by enhancing the traditional MPCP signaling protocol, which cooperatively collects mobility information from the front-end wireless network and makes centralized bandwidth allocation decisions in the backhaul optical network. The integrated network architecture and the joint handover scheme are simulated using...... OPNET modeler. Results show validation of the protocol, i.e., integrated handover scheme gains better network performances....

  20. Analysis of Sleep-Mode Downlink Scheduling Operations in EPON Systems

    DEFF Research Database (Denmark)

    Yan, Ying; Dittmann, Lars

    2011-01-01

    Energy management strategy has been considered as an important component in the future Ethernet Passive Optical Networks (EPONs). In this paper, a sleeping mode operation is studied, and a downlink packet scheduling scheme is analyzed to preserve energy consumption and maintain the required Qo......S. This paper proposes a novel sleep-mode downlink packet scheduling scheme in order to enhance the sleep control function. Simulation results confirm that the proposed approach offers effective power management on the basis of the traffic conditions. The trade-off between network performances and the power...

  1. Distortion of 3D SU8 photonic structures fabricated by four-beam holographic lithography withumbrella configuration.

    Science.gov (United States)

    Zhu, Xuelian; Xu, Yongan; Yang, Shu

    2007-12-10

    We present a quantitative study of the distortion from a threeterm diamond-like structure fabricated in SU8 polymer by four-beam holographic lithography. In the study of the refraction effect, theory suggests that the lattice in SU8 should be elongated in the [111] direction but have no distortion in the (111) plane, and each triangular-like hole array in the (111) plane would rotate by ~30 degrees away from that in air. Our experiments agree with the prediction on the periodicity in the (111) plane and the rotation due to refraction effect, however, we find that the film shrinkage during lithographic process has nearly compensated the predicted elongation in the [111] direction. In study of photonic bandgap (PBG) properties of silicon photonic crystals templated by the SU8 structure, we find that the distortion has decreased quality of PBG.

  2. Development of 3D out-of-plane SU-8 microlenses using modified micromolding in capillaries (MIMIC) technology

    Science.gov (United States)

    Llobera, A.; Wilke, R.; Johnson, D. W.; Büttgenbach, S.

    2006-04-01

    This paper describes a modification of the standard MIMIC technology, solving its main drawbacks, to define arrays of spherical or ellipsoidal microlenses. Perfectly symmetrical meniscuses have been obtained by using a XP SU-8 NO-2 layer beneath the PDMS mold. Moreover, the photostructurable properties of this polymer allow obtaining self-alignment structures for adequate fiber optics positioning. Microchannels ended with these meniscuses have been filled with standard SU-8 to obtain 3D microlenses. Agreement between theory and experimental results allows confirming the validity of the proposed technology.

  3. An SU-8-based microprobe with a nanostructured surface enhances neuronal cell attachment and growth

    Science.gov (United States)

    Kim, Eunhee; Kim, Jin-Young; Choi, Hongsoo

    2017-12-01

    Microprobes are used to repair neuronal injury by recording electrical signals from neuronal cells around the surface of the device. Following implantation into the brain, the immune response results in formation of scar tissue around the microprobe. However, neurons must be in close proximity to the microprobe to enable signal recording. A common reason for failure of microprobes is impaired signal recording due to scar tissue, which is not related to the microprobe itself. Therefore, the device-cell interface must be improved to increase the number of neurons in contact with the surface. In this study, we developed nanostructured SU-8 microprobes to support neuronal growth. Nanostructures of 200 nm diameter and depth were applied to the surface of microprobes, and the attachment and neurite outgrowth of PC12 cells on the microprobes were evaluated. Neuronal attachment and neurite outgrowth on the nanostructured microprobes were significantly greater than those on non-nanostructured microprobes. The enhanced neuronal attachment and neurite outgrowth on the nanostructured microprobes occurred in the absence of an adhesive coating, such as poly- l-lysine, and so may be useful for implantable devices for long-term use. Therefore, nanostructured microprobes can be implanted without adhesive coating, which can cause problems in vivo over the long term.

  4. Fermion unification model based on the intrinsic SU(8 symmetry of a generalized Dirac equation

    Directory of Open Access Journals (Sweden)

    Eckart eMarsch

    2015-10-01

    Full Text Available A natural generalization of the original Dirac spinor into a multi-component spinor is achieved, which corresponds to the single lepton and the three quarks of the first family of the standard model of elementary particle physics. Different fermions result from similarity transformations of the Dirac equation, but apparently there can be no more fermions according to the maximal multiplicity revealed in this study. Rotations in the fermion state space are achieved by the unitary generators of the U(1 and the SU(3 groups, corresponding to quantum electrodynamics (QED based on electric charge and chromodynamics (QCD based on colour charge. In addition to hypercharge the dual degree of freedom of hyperspin emerges, which occurs due to the duplicity implied by the two related (Weyl and Dirac representations of the Dirac equation. This yields the SU(2 symmetry of the weak interaction, which can be married to U(1 to generate the unified electroweak interaction as in the standard model. Therefore, the symmetry group encompassing all the three groups mentioned above is SU(8, which can accommodate and unify the observed eight basic stable fermions.

  5. MEMS flexible artificial basilar membrane fabricated from piezoelectric aluminum nitride on an SU-8 substrate

    International Nuclear Information System (INIS)

    Jang, Jongmoon; Choi, Hongsoo; Jang, Jeong Hun

    2017-01-01

    In this paper, we present a flexible artificial basilar membrane (FABM) that mimics the passive mechanical frequency selectivity of the basilar membrane. The FABM is composed of a cantilever array made of piezoelectric aluminum nitride (AlN) on an SU-8 substrate. We analyzed the orientations of the AlN crystals using scanning electron microscopy and x-ray diffraction. The AIN crystals are oriented in the c -axis (0 0 2) plane and effective piezoelectric coefficient was measured as 3.52 pm V −1 . To characterize the frequency selectivity of the FABM, mechanical displacements were measured using a scanning laser Doppler vibrometer. When electrical and acoustic stimuli were applied, the measured resonance frequencies were in the ranges of 663.0–2369 Hz and 659.4–2375 Hz, respectively. These results demonstrate that the mechanical frequency selectivity of this piezoelectric FABM is close to the human communication frequency range (300–3000 Hz), which is a vital feature of potential auditory prostheses. (paper)

  6. Single Mode SU8 Polymer Based Mach-Zehnder Interferometer for Bio-Sensing Application

    Science.gov (United States)

    Boiragi, Indrajit; Kundu, Sushanta; Makkar, Roshan; Chalapathi, Krishnamurthy

    2011-10-01

    This paper explains the influence of different parameters to the sensitivity of an optical waveguide Mach-Zehnder Interferometer (MZI) for real time detection of biomolecules. The sensing principle is based on the interaction of evanescence field with the biomolecules that get immobilized on sensing arm. The sensitivity has been calculated by varying the sensing window length, wavelength and concentration of bio-analyte. The maximum attainable sensitivity for the preferred design is the order of 10-8 RIU at 840 nm wavelength with a sensing window length of 1cm. All the simulation work has been carried out with Opti-BPMCAD for the optimization of MZI device parameters. The SU8 polymers are used as a core and clad material to fabricate the waveguide. The refractive index of cladding layer is optimized by varying the curing temperature for a fixed time period and the achieved index difference between core and clad is Δn = 0.0151. The fabricated MZI device has been characterized with LASER beam profiler at 840 nm wavelength. This study demonstrates the effectiveness of the different parameter to the sensitivity of a single mode optical waveguide Mach-Zehnder Interferometer for bio-sensing application.

  7. Thin film free-standing PEDOT:PSS/SU8 bilayer microactuators

    International Nuclear Information System (INIS)

    Taccola, S; Greco, F; Mazzolai, B; Mattoli, V; Jager, E W H

    2013-01-01

    Several smart active materials have been proposed and tested for the development of microactuators. Among these, conjugated polymers are of great interest because miniaturization improves their electrochemical properties, such as increasing the speed and stress output of microactuators, with respect to large-scale actuators. Recently we developed a novel fabrication process to obtain robust free-standing conductive ultra-thin films made of the conjugated polymer poly(3, 4-ethylenedioxythiophene) doped with the polyanion poly(styrenesulfonate) (PEDOT:PSS). These conductive free-standing nanofilms, with thicknesses ranging between a few tens to several hundreds of nm, allow the realisation of new all polymer microactuators using facile microfabrication methods. Here, we report a novel processing method for manufacturing all polymer electrochemical microactuators. We fabricated and patterned free-standing PEDOT:PSS/SU8 bilayer microactuators in the form of microfingers of a variety of lengths using adapted microfabrication procedures. By imposing electrochemical oxidation/reduction cycles on the PEDOT:PSS we were able to demonstrate reversible actuation of the microactuators resulting in bending of the microfingers. A number of possible applications can be envisaged for these small, soft actuators, such as microrobotics and cell manipulation. (technical note)

  8. Study of functional viability of SU-8-based microneedles for neural applications

    International Nuclear Information System (INIS)

    Fernández, Luis J; Altuna, Ane; Tijero, Maria; Vilares, Roman; Berganzo, Javier; Blanco, F J; Gabriel, Gemma; Villa, Rosa; Rodríguez, Manuel J; Batlle, Montse

    2009-01-01

    This paper presents the design, fabrication, packaging and first test results of SU-8-based microneedles for neural applications. By the use of photolithography, sputtering and bonding techniques, polymer needles with integrated microchannels and electrodes have been successfully fabricated. The use of photolithography for the patterning of the fluidic channel integrated in the needle allows the design of multiple outlet ports at the needle tip, minimizing the possibility of being blocked by the tissue. Furthermore, the flexibility of the polymer reduces the risk of fracture and tissue damage once the needle is inserted, while it is still rigid enough to allow a perfect insertion into the neural tissue. Fluidic and electric characterization of the microneedles has shown their viability for drug delivery and monitoring in neural applications. First drug delivery tests in ex vivo tissue demonstrated the functional viability of the needle to deliver drugs to precise points. Furthermore, in vivo experiments have demonstrated lower associated damages during insertion than those by stereotaxic standard needles

  9. An autonomous recovery mechanism against optical distribution network failures in EPON

    Science.gov (United States)

    Liem, Andrew Tanny; Hwang, I.-Shyan; Nikoukar, AliAkbar

    2014-10-01

    Ethernet Passive Optical Network (EPON) is chosen for servicing diverse applications with higher bandwidth and Quality-of-Service (QoS), starting from Fiber-To-The-Home (FTTH), FTTB (business/building) and FTTO (office). Typically, a single OLT can provide services to both residential and business customers on the same Optical Line Terminal (OLT) port; thus, any failures in the system will cause a great loss for both network operators and customers. Network operators are looking for low-cost and high service availability mechanisms that focus on the failures that occur within the drop fiber section because the majority of faults are in this particular section. Therefore, in this paper, we propose an autonomous recovery mechanism that provides protection and recovery against Drop Distribution Fiber (DDF) link faults or transceiver failure at the ONU(s) in EPON systems. In the proposed mechanism, the ONU can automatically detect any signal anomalies in the physical layer or transceiver failure, switching the working line to the protection line and sending the critical event alarm to OLT via its neighbor. Each ONU has a protection line, which is connected to the nearest neighbor ONU, and therefore, when failure occurs, the ONU can still transmit and receive data via the neighbor ONU. Lastly, the Fault Dynamic Bandwidth Allocation for recovery mechanism is presented. Simulation results show that our proposed autonomous recovery mechanism is able to maintain the overall QoS performance in terms of mean packet delay, system throughput, packet loss and EF jitter.

  10. Development of an SU-8 MEMS process with two metal electrodes using amorphous silicon as a sacrificial material

    KAUST Repository

    Ramadan, Khaled S.; Nasr, Tarek Adel Hosny; Foulds, Ian G.

    2013-01-01

    method using XeF2, which alleviates release-based stiction problems related to MEMS applications. In this work, an SU-8 MEMS process was developed using ;-Si as a sacrificial layer. Two conductive metal electrodes were integrated in this process to allow

  11. SU-8 Based MEMS Process with Two Metal Layers using α-Si as a Sacrificial Material

    KAUST Repository

    Ramadan, Khaled S.

    2012-01-01

    MEMS applications. α-Si can be deposited at large thicknesses for MEMS applications and also can be released in a dry method using XeF2 which can solve stiction problems related to MEMS applications. In this thesis, an SU-8 MEMS process is developed

  12. Order of multiphoton excitation of sulfonium photo-acid generators used in photoresists based on SU-8

    Science.gov (United States)

    Williams, Henry E.; Diaz, Carlos; Padilla, Gabriel; Hernandez, Florencio E.; Kuebler, Stephen M.

    2017-06-01

    Multiphoton lithography (MPL), Z-scan spectroscopy, and quantum chemical calculations were employed to investigate the order of multiphoton excitation that occurs when femtosecond laser pulses are used to excite two sulfonium photo-acid generators (PAGs) commonly used in photoresists based on the cross-linkable epoxide SU-8. The mole-fractions of the mono- and bis-sulfonium forms of these PAGs were determined for the commercially available photoresist SU-8 2075 and for the PAGs alone from a separate source. Both were found to contain similar fractions of the mono- and bis-forms, with the mono form present in the majority. Reichert's method was used to determine the solvatochromic strength of the SU-8 matrix, so that results obtained for the PAGs in SU-8 and in solution could be reliably compared. The PAGs were found to exhibit a minimal solvatochromic shift for a series of solvents that span across the solvatochromic strength of SU-8 itself. Sub-micron-sized features were fabricated in SU-8 2075 by MPL using amplified and continuous-wave mode-locked laser pulses. Analysis of the features as a function of average laser power, scan speed, and excitation wavelength shows that the PAGs can be activated by both two- and three-photon absorption (2PA and 3PA). Which activation mode dominates depends principally upon the excitation wavelength because the average laser powers that can be used with the photoresist are limited by practical considerations. The power must be high enough to effect sufficient cross-linking, yet not so high as to exceed the damage threshold of the material. When the laser pulses have a duration on the order of 100 fs, 3PA dominates at wavelengths near 800 nm, whereas 2PA becomes dominant at wavelengths below 700 nm. These findings are corroborated by open-aperture Z-scan measurements and quantum chemical calculations of the cross-sections for 2PA and 3PA as a function of wavelength.

  13. Blind void filling in LR-EPONs: How efficient it can be?

    KAUST Repository

    Elrasad, Amr; Shihada, Basem

    2015-01-01

    This work proposes a novel blind void (idle periods) filling in Long-Reach Ethernet Passive Optical Networks (LR-EPONs) namely Size Controlled Batch Void Filling (SCBVF). We emphasize on reducing grant delays and hence reducing the average packet delay. SCBVF delay reduction is achieved by early flushing data during the idle time periods (voids) between allocated grants. The proposed approach can be integrated with almost all of the previously reported dynamic bandwidth allocation schemes. SCBVF is less sensitive to differential distance between ONUs and can work well in case of small differential distances compared to previously reported void filling schemes. We support our work by extensive simulation study considering bursty traffic with long range dependency. Numerical results show a delay reduction up to 35% compared to non-void filling scheme outperforming its main competitors that can achieve up to 7% delay reduction.

  14. Blind void filling in LR-EPONs: How efficient it can be?

    KAUST Repository

    Elrasad, Amr

    2015-07-01

    This work proposes a novel blind void (idle periods) filling in Long-Reach Ethernet Passive Optical Networks (LR-EPONs) namely Size Controlled Batch Void Filling (SCBVF). We emphasize on reducing grant delays and hence reducing the average packet delay. SCBVF delay reduction is achieved by early flushing data during the idle time periods (voids) between allocated grants. The proposed approach can be integrated with almost all of the previously reported dynamic bandwidth allocation schemes. SCBVF is less sensitive to differential distance between ONUs and can work well in case of small differential distances compared to previously reported void filling schemes. We support our work by extensive simulation study considering bursty traffic with long range dependency. Numerical results show a delay reduction up to 35% compared to non-void filling scheme outperforming its main competitors that can achieve up to 7% delay reduction.

  15. Comparison of three different scales techniques for the dynamic mechanical characterization of two polymers (PDMS and SU8)

    Science.gov (United States)

    Le Rouzic, J.; Delobelle, P.; Vairac, P.; Cretin, B.

    2009-10-01

    In this article the dynamic mechanical characterization of PDMS and SU8 resin using dynamic mechanical analysis, nanoindentation and the scanning microdeformation microscope have been presented. The methods are hereby explained, extended for viscoelastic behaviours, and their compatibility underlined. The storage and loss moduli of these polymers over a wide range of frequencies (from 0.01 Hz to somekHz) have been measured. These techniques are shown fairly matching and the two different viscoelastic behaviours of these two polymers have been exhibited. Indeed, PDMS shows moduli which still increase at 5kHz whereas SU8 ones decrease much sooner. From a material point of view, the Havriliak and Negami model to estimate instantaneous, relaxed moduli and time constant of these materials has been identified.

  16. An isotropic suspension system for a biaxial accelerometer using electroplated thick metal with a HAR SU-8 mold

    International Nuclear Information System (INIS)

    Lee, Jin Seung; Lee, Seung S

    2008-01-01

    In this paper, a novel approach is developed to design an isotropic suspension system using thick metal freestanding micro-structures combining bulk micro-machining with electroplating based on a HAR SU-8 mold. An omega-shape isotropic suspension system composed of circular curved beams that have free switching of imaginary boundary conditions is proposed. This novel isotropic suspension design is not affected by geometric dimensional parameters and always achieves matching stiffness along the principle axes of elasticity. Using the finite element method, the isotropic suspension system was compared with an S-shaped meandering suspension system. In order to realize the suggested isotropic suspension system, a cost-effective fabrication process using electroplating with the SU-8 mold was developed to avoid expensive equipment and materials such as deep reactive-ion etching (DRIE) or a silicon-on-insulator (SOI) wafer. The fabricated isotropic suspension system was verified by electromagnetic actuation experiments. Finally, a biaxial accelerometer with isotropic suspension system was realized and tested using a vibration generator system. The proposed isotropic suspension system and the modified surface micro-machining technique based on electroplating with an SU-8 mold can contribute towards minimizing the system size, simplifying the system configuration, reducing the system price of and facilitating mass production of various types of low-cost sensors and actuators

  17. Injection and waveguiding properties in SU8 nanotubes for sub-wavelength regime propagation and nanophotonics integration

    Science.gov (United States)

    Bigeon, John; Huby, Nolwenn; Duvail, Jean-Luc; Bêche, Bruno

    2014-04-01

    We report photonic concepts related to injection and sub-wavelength propagation in nanotubes, an unusual but promising geometry for highly integrated photonic devices. Theoretical simulation by the finite domain time-dependent (FDTD) method was first used to determine the features of the direct light injection and sub-wavelength propagation regime within nanotubes. Then, the injection into nanotubes of SU8, a photoresist used for integrated photonics, was successfully achieved by using polymer microlensed fibers with a sub-micronic radius of curvature, as theoretically expected from FDTD simulations. The propagation losses in a single SU8 nanotube were determined by using a comprehensive set-up and a protocol for optical characterization. The attenuation coefficient has been evaluated at 1.25 dB mm-1 by a cut-back method transposed to such nanostructures. The mechanisms responsible for losses in nanotubes were identified with FDTD theoretical support. Both injection and cut-back methods developed here are compatible with any sub-micronic structures. This work on SU8 nanotubes suggests broader perspectives for future nanophotonics.

  18. Proton beam writing on PMMA and SU-8 films as a tool for development of micro-structures for organic electronics

    Energy Technology Data Exchange (ETDEWEB)

    Sarkar, Mihir, E-mail: mihirs@iitk.ac.in [Department of Physics, Indian Institute of Technology Kanpur, Kanpur 208016 (India); Shukla, Neeraj; Banerji, Nobin [Department of Physics, Indian Institute of Technology Kanpur, Kanpur 208016 (India); Mohapatra, Y.N. [Department of Physics, Indian Institute of Technology Kanpur, Kanpur 208016 (India); Materials Science Programme, Indian Institute of Technology Kanpur, Kanpur 208016 (India); Samtel Center for Display Technologies, Indian Institute of Technology Kanpur, Kanpur 208016 (India)

    2012-02-15

    Proton beam writing is a maskless lithographic technique for the fabrication of 3D micro and nano structures in polymers. The fabricated structures find application in micro fluidics, optics, biosensors, etc. We use proton beam writing for micro-patterning in polymers which will facilitate fabrication of test structures for micro-components of micro-fluidic devices, organic thin film transistors (OTFT) and organic light emitting diodes (OLED). In this paper we report fabrication of varying width micro channels in PMMA and SU-8 films used as positive and negative resists respectively. The patterns were written using 2 MeV proton beam focused down to around 1 micron. We have achieved clean periodic micro-channels of width varying from few micrometers to wider ones in both the resists. Being a mask less lithography it provides an efficient way of reducing turnaround time for test structures with several channel widths and patterns being conveniently written at the same development cycle. Possible applications of the patterned structures in OLED/TFT are discussed. Additional structures like checkered board are also fabricated. Optimized fluence for both the resist has been determined.

  19. Molybdenum coated SU-8 microneedle electrodes for transcutaneous electrical nerve stimulation.

    Science.gov (United States)

    Soltanzadeh, Ramin; Afsharipour, Elnaz; Shafai, Cyrus; Anssari, Neda; Mansouri, Behzad; Moussavi, Zahra

    2017-11-21

    Electrophysiological devices are connected to the body through electrodes. In some applications, such as nerve stimulation, it is needed to minimally pierce the skin and reach the underneath layers to bypass the impedance of the first layer called stratum corneum. In this study, we have designed and fabricated surface microneedle electrodes for applications such as electrical peripheral nerve stimulation. We used molybdenum for microneedle fabrication, which is a biocompatible metal; it was used for the conductive layer of the needle array. To evaluate the performance of the fabricated electrodes, they were compared with the conventional surface electrodes in nerve conduction velocity experiment. The recorded signals showed a much lower contact resistance and higher bandwidth in low frequencies for the fabricated microneedle electrodes compared to those of the conventional electrodes. These results indicate the electrode-tissue interface capacitance and charge transfer resistance have been increased in our designed electrodes, while the contact resistance decreased. These changes will lead to less harmful Faradaic current passing through the tissue during stimulation in different frequencies. We also compared the designed microneedle electrodes with conventional ones by a 3-dimensional finite element simulation. The results demonstrated that the current density in the deep layers of the skin and the directivity toward a target nerve for microneedle electrodes were much more than those for the conventional ones. Therefore, the designed electrodes are much more efficient than the conventional electrodes for superficial transcutaneous nerve stimulation purposes.

  20. An energy saving mechanism of EPON networks for real time video transmission

    Science.gov (United States)

    Liu, Chien-Ping; Wu, Ho-Ting; Chiang, Yun-Ting; Chien, Shieh-Chieh; Ke, Kai-Wei

    2015-07-01

    Modern access networks are constructed widely by passive optical networks (PONs) to meet the growing bandwidth demand. However, higher bandwidth means more energy consumption. To save energy, a few research works propose the dual-mode energy saving mechanism that allows the ONU to operate between active and sleep modes periodically. However, such dual-mode energy saving design may induce unnecessary power consumption or packet delay increase in the case where only downstream data exist for most of the time. In this paper, we propose a new tri-mode energy saving scheme for Ethernet PON (EPON). The new tri-mode energy saving design, combining the dual-mode saving mechanism with the doze mode, allows the ONU to switch among these three modes alternatively. In the doze mode, the ONU may receive downstream data while keeping its transmitter close. Such scenario is often observed for real time video downstream transmission. Furthermore, the low packet delay of high priority upstream data can be attained through the use of early wake-up mechanism employed in both energy saving modes. The energy saving and system efficiency can thus be achieved jointly while maintaining the differentiated QoS for data with various priorities. Performance results via simulation have demonstrated the effectiveness of such mechanism.

  1. Heavy Traffic Feasible Hybrid Intracycle and Cyclic Sleep for Power Saving in 10G-EPON

    Directory of Open Access Journals (Sweden)

    Xintian Hu

    2014-01-01

    Full Text Available Energy consumption in optical access networks costs carriers substantial operational expense (OPEX every year and is one of contributing factors for the global warming. To reduce energy consumption in the 10-gigabit Ethernet passive optical network (10G-EPON, a hybrid intracycle and cyclic sleep mechanism is proposed in this paper. Under heavy traffic load, optical network units (ONUs can utilize short idle slots within each scheduling cycle to enter intracycle sleep without postponing data transmission. In this way, energy conservation is achieved even under heavy traffic load with quality of service (QoS guarantee. Under light traffic load, ONUs perform long cyclic sleep for several scheduling cycles. The adoption of cyclic sleep instead of intracycle sleep under light traffic load can reduce unnecessary frequent transitions between sleep and full active work caused by using intracycle sleep. Further, the Markov chain of the proposed mechanism is established. The performances of the proposed mechanism and existing approaches are analyzed quantitatively based on the chain. For the proposed mechanism, power saving ability with QoS guarantee even under heavy traffic and better power saving performance than existing approaches are verified by the quantitative analysis. Moreover, simulations validate the above conclusions based on the chain.

  2. A high aspect ratio SU-8 fabrication technique for hollow microneedles for transdermal drug delivery and blood extraction

    Science.gov (United States)

    Chaudhri, Buddhadev Paul; Ceyssens, Frederik; De Moor, Piet; Van Hoof, Chris; Puers, Robert

    2010-06-01

    Protein drugs, e.g. hormonal drugs, cannot be delivered orally to a patient as they get digested in the gastro-intestinal (GI) tract. Thus, it is imperative that these kinds of drugs are delivered transdermally through the skin. To provide for real-time feedback as well as to test independently for various substances in the blood, we also need a blood sampling system. Microneedles can perform both these functions. Further, microneedles made of silicon or metal have the risk of breaking inside the skin thereby leading to complications. SU-8, being approved of as being biocompatible by the Food and Drug Agency (FDA) of the United States, is an attractive alternative because firstly it is a polymer material, thereby reducing the chances of breakages inside the skin, and secondly it is a negative photoresist, thereby leading to ease of fabrication. Thus, here we present very tall (around 1600 µm) SU-8 polymer-based hollow microneedles fabricated by a simple and repeatable process, which are a very good candidate for transdermal drug delivery as well as blood extraction. The paper elaborates on the details that allow the fabrication of such extreme aspect ratios (>100).

  3. A high aspect ratio SU-8 fabrication technique for hollow microneedles for transdermal drug delivery and blood extraction

    International Nuclear Information System (INIS)

    Chaudhri, Buddhadev Paul; Ceyssens, Frederik; Van Hoof, Chris; Puers, Robert; De Moor, Piet

    2010-01-01

    Protein drugs, e.g. hormonal drugs, cannot be delivered orally to a patient as they get digested in the gastro-intestinal (GI) tract. Thus, it is imperative that these kinds of drugs are delivered transdermally through the skin. To provide for real-time feedback as well as to test independently for various substances in the blood, we also need a blood sampling system. Microneedles can perform both these functions. Further, microneedles made of silicon or metal have the risk of breaking inside the skin thereby leading to complications. SU-8, being approved of as being biocompatible by the Food and Drug Agency (FDA) of the United States, is an attractive alternative because firstly it is a polymer material, thereby reducing the chances of breakages inside the skin, and secondly it is a negative photoresist, thereby leading to ease of fabrication. Thus, here we present very tall (around 1600 µm) SU-8 polymer-based hollow microneedles fabricated by a simple and repeatable process, which are a very good candidate for transdermal drug delivery as well as blood extraction. The paper elaborates on the details that allow the fabrication of such extreme aspect ratios (>100).

  4. Nonlinear numerical analysis and experimental testing for an electrothermal SU-8 microgripper with reduced out-of-plane displacement

    Science.gov (United States)

    Voicu, Rodica-Cristina; Zandi, Muaiyd Al; Müller, Raluca; Wang, Changhai

    2017-11-01

    This paper reports the results of numerical nonlinear electro-thermo-mechanical analysis and experimental testing of a polymeric microgripper designed using electrothermal actuators. The simulation work was carried out using a finite element method (FEM) and a commercial software (Coventorware 2014). The biocompatible SU-8 polymer was used as structural material for the fabrication of the microgripper. The metallic micro-heater was encapsulated in the polymeric actuation structures of the microgripper to reduce the undesirable out-of-plane displacement of the microgripper tips, and to electrically isolate the micro-heater, and to reduce the mechanical stress as well as to improve the thermal efficiency. The electro- thermo-mechanical analysis of the actuator considers the nonlinear temperature-dependent properties of the SU-8 polymer and the gold thin film layers used for the micro-heater fabrication. An optical characterisation of the microgripper based on an image tracking approach shows the thermal response and the good repeatability. The average deflection is ~11 µm for an actuation current of ~17 mA. The experimentally obtained tip deflection and the heater temperature at different currents are both shown to be in good agreement with the nonlinear electro-thermo-mechanical simulation results. Finally, we demonstrate the capability of the microgripper by capture and manipulation of cotton fibres.

  5. Organic Field-Effect Transistors Based on a Liquid-Crystalline Polymeric Semiconductor using SU-8 Gate Dielectrics on Flexible Substrates

    Science.gov (United States)

    Tetzner, Kornelius; Bose, Indranil R.; Bock, Karlheinz

    2014-01-01

    In this work, the insulating properties of poly(4-vinylphenol) (PVP) and SU-8 (MicroChem, Westborough, MA, USA) dielectrics are analyzed and compared with each other. We further investigate the performance behavior of organic field-effect transistors based on a semiconducting liquid-crystal polymer (LCP) using both dielectric materials and evaluate the results regarding the processability. Due to the lower process temperature needed for the SU-8 deposition, the realization of organic transistors on flexible substrates is demonstrated showing comparable charge carrier mobilities to devices using PVP on glass. In addition, a µ-dispensing procedure of the LCP on SU-8 is presented, improving the switching behavior of the organic transistors, and the promising stability data of the SU-8/LCP stack are verified after storing the structures for 60 days in ambient air showing negligible irreversible degradation of the organic semiconductor. PMID:28788243

  6. Organic Field-Effect Transistors Based on a Liquid-Crystalline Polymeric Semiconductor using SU-8 Gate Dielectrics onFlexible Substrates

    Directory of Open Access Journals (Sweden)

    Kornelius Tetzner

    2014-10-01

    Full Text Available In this work, the insulating properties of poly(4-vinylphenol (PVP and SU-8 (MicroChem, Westborough, MA, USA dielectrics are analyzed and compared with each other. We further investigate the performance behavior of organic field-effect transistors based on a semiconducting liquid-crystal polymer (LCP using both dielectric materials and evaluate the results regarding the processability. Due to the lower process temperature needed for the SU-8 deposition, the realization of organic transistors on flexible substrates is demonstrated showing comparable charge carrier mobilities to devices using PVP on glass. In addition, a µ-dispensing procedure of the LCP on SU-8 is presented, improving the switching behavior of the organic transistors, and the promising stability data of the SU-8/LCP stack are verified after storing the structures for 60 days in ambient air showing negligible irreversible degradation of the organic semiconductor.

  7. Organic Field-Effect Transistors Based on a Liquid-Crystalline Polymeric Semiconductor using SU-8 Gate Dielectrics onFlexible Substrates.

    Science.gov (United States)

    Tetzner, Kornelius; Bose, Indranil R; Bock, Karlheinz

    2014-10-29

    In this work, the insulating properties of poly(4-vinylphenol) (PVP) and SU-8 (MicroChem, Westborough, MA, USA) dielectrics are analyzed and compared with each other. We further investigate the performance behavior of organic field-effect transistors based on a semiconducting liquid-crystal polymer (LCP) using both dielectric materials and evaluate the results regarding the processability. Due to the lower process temperature needed for the SU-8 deposition, the realization of organic transistors on flexible substrates is demonstrated showing comparable charge carrier mobilities to devices using PVP on glass. In addition, a µ-dispensing procedure of the LCP on SU-8 is presented, improving the switching behavior of the organic transistors, and the promising stability data of the SU-8/LCP stack are verified after storing the structures for 60 days in ambient air showing negligible irreversible degradation of the organic semiconductor.

  8. Heterogeneous integration of thin film compound semiconductor lasers and SU8 waveguides on SiO2/Si

    Science.gov (United States)

    Palit, Sabarni; Kirch, Jeremy; Mawst, Luke; Kuech, Thomas; Jokerst, Nan Marie

    2010-02-01

    We present the heterogeneous integration of a 3.8 μm thick InGaAs/GaAs edge emitting laser that was metal-metal bonded to SiO2/Si and end-fire coupled into a 2.8 μm thick tapered SU8 polymer waveguide integrated on the same substrate. The system was driven in pulsed mode and the waveguide output was captured on an IR imaging array to characterize the mode. The waveguide output was also coupled into a multimode fiber, and into an optical head and spectrum analyzer, indicating lasing at ~997 nm and a threshold current density of 250 A/cm2.

  9. The influence of hard-baking temperature applied for SU8 sensor layer on the sensitivity of capacitive chemical sensor

    Science.gov (United States)

    Klanjšek Gunde, Marta; Hauptman, Nina; Maček, Marijan; Kunaver, Matjaž

    2009-06-01

    SU8, the near-UV photosensitive epoxy-based polymer was used as a sensor layer in the capacitive chemical sensor, ready for integration with a generic double-metal CMOS technology. It was observed that the response of the sensor slowly increases with the temperature applied in hard-baking process as long as it remains below 300°C. At this temperature the response of the sensor abruptly increases and becomes almost threefold. It was shown that fully crosslinked structure of the sensor layer becomes opened and disordered when the sensor is hard-baked at temperatures between 300°C and 320°C, that is, still well below the degradation temperature of the polymer. These changes in chemical structure were analyzed by Fourier-transform infrared spectroscopy. The temperature-dependent changes of the sensor layer structure enable one to prepare a combination of capacitive chemical sensors with good discrimination between some volatile organic compounds.

  10. Characterization of channel waveguides and tunable microlasers in SU8 doped with rhodamine B fabricated using proton beam writing

    International Nuclear Information System (INIS)

    Rao, S Venugopal; Bettiol, A A; Watt, F

    2008-01-01

    We present our results on the fabrication and characterization of buried channel waveguides and tunable microlasers in SU8 doped with rhodamine B achieved using direct writing with a 2.0 MeV proton beam. The channel waveguides, fabricated in single exposure, had an optical propagation loss of -1 at 532 nm measured using the scattering technique while the microlasers with dimensions of 250 x 250 μm 2 had a threshold of ∼150 μJ mm -2 when pumped with 532 nm nanosecond pulses. The emitted wavelength from the microlasers was tunable to an extent of ∼15 nm with increasing pump intensity and different pumping angles. The advantages of such micro-photonic components for the realization of a lab-on-a-chip device are discussed briefly. (fast track communication)

  11. Paper Microzone Plates as Analytical Tools for Studying Enzyme Stability: A Case Study on the Stabilization of Horseradish Peroxidase Using Trehalose and SU-8 Epoxy Novolac Resin.

    Science.gov (United States)

    Ganaja, Kirsten A; Chaplan, Cory A; Zhang, Jingyi; Martinez, Nathaniel W; Martinez, Andres W

    2017-05-16

    Paper microzone plates in combination with a noncontact liquid handling robot were demonstrated as tools for studying the stability of enzymes stored on paper. The effect of trehalose and SU-8 epoxy novolac resin (SU-8) on the stability of horseradish peroxidase (HRP) was studied in both a short-term experiment, where the activity of various concentrations of HRP dried on paper were measured after 1 h, and a long-term experiment, where the activity of a single concentration of HRP dried and stored on paper was monitored for 61 days. SU-8 was found to stabilize HRP up to 35 times more than trehalose in the short-term experiment for comparable concentrations of the two reagents, and a 1% SU-8 solution was found to stabilize HRP approximately 2 times more than a 34% trehalose solution in both short- and long-term experiments. The results suggest that SU-8 is a promising candidate for use as an enzyme-stabilizing reagent for paper-based diagnostic devices and that the short-term experiment could be used to quickly evaluate the capacity of various reagents for stabilizing enzymes to identify and characterize new enzyme-stabilizing reagents.

  12. Variable disparity estimation based intermediate view reconstruction in dynamic flow allocation over EPON-based access networks

    Science.gov (United States)

    Bae, Kyung-Hoon; Lee, Jungjoon; Kim, Eun-Soo

    2008-06-01

    In this paper, a variable disparity estimation (VDE)-based intermediate view reconstruction (IVR) in dynamic flow allocation (DFA) over an Ethernet passive optical network (EPON)-based access network is proposed. In the proposed system, the stereoscopic images are estimated by a variable block-matching algorithm (VBMA), and they are transmitted to the receiver through DFA over EPON. This scheme improves a priority-based access network by converting it to a flow-based access network with a new access mechanism and scheduling algorithm, and then 16-view images are synthesized by the IVR using VDE. Some experimental results indicate that the proposed system improves the peak-signal-to-noise ratio (PSNR) to as high as 4.86 dB and reduces the processing time to 3.52 s. Additionally, the network service provider can provide upper limits of transmission delays by the flow. The modeling and simulation results, including mathematical analyses, from this scheme are also provided.

  13. Fabrication of a roller type PDMS stamp using SU-8 concave molds and its application for roll contact printing

    International Nuclear Information System (INIS)

    Park, Jongho; Kim, Beomjoon

    2016-01-01

    Continuous fabrication of micropatterns at low-cost is attracting attention in various applications within industrial fields. To meet such demands, we have demonstrated a roll contact printing technique, using roller type polydimethylsiloxane (PDMS) stamps with roll-to-flat and roll-to-roll stages. Roller type PDMS stamps for roll contact printing were fabricated using a custom-made metal support and SU-8 microstructures fabricated on concave substrates as a mold. The molding/casting method which we developed here provided faster and easier fabrication than conventional methods for roller type stamps. Next, roll contact printing was performed using fabricated roller type PDMS stamps with roll-to-flat and roll-to-roll stages. Patterns with minimum widths of 3 μm and 2.1 μm were continuously fabricated for each stage, respectively. In addition, the relationship between applied pressures and dimensional changes of roll contact printed patterns was investigated. Finally, we confirmed that roll contact printing and the new fabrication method for roller stamps presented in this study demonstrated the feasibility for industrial applications. (paper)

  14. Contact printed masks for 3D microfabrication in negative resists

    DEFF Research Database (Denmark)

    Häfliger, Daniel; Boisen, Anja

    2005-01-01

    We present a process based on contact printed shadow masks for three dimensional microfabrication of soft and sensitive overhanging membranes in SU-8. A metal mask is transferred onto unexposed SU-8 from an elastomer stamp made of polydimethylsiloxane. This mask is subsequently embedded into the ......We present a process based on contact printed shadow masks for three dimensional microfabrication of soft and sensitive overhanging membranes in SU-8. A metal mask is transferred onto unexposed SU-8 from an elastomer stamp made of polydimethylsiloxane. This mask is subsequently embedded...... into the negative resist to protect buried material from UV-exposure. Unlike direct evaporation-deposition of a mask onto the SU-8, printing avoids high stress and radiation, thus preventing resist wrinkling and prepolymerization. We demonstrate effective monolithic fabrication of soft, 4-μm thick and 100-μm long...

  15. Investigation of a novel approach for the cross-linking characterization of SU-8 photoresist materials by means of optical dispersion measurements

    Science.gov (United States)

    Taudt, Ch.; Baselt, T.; Koch, E.; Hartmann, P.

    2014-03-01

    The increase in efficiency and precision in the production of semiconductor structures under the use of polymeric materials like SU-8 is crucial in securing the technological innovation within this industry. The manufacturing of structures on wafers demands a high quality of materials, tools and production processes. In particular, deviations in the materials' parameters (e.g. cross-linking state, density or mechanical properties) could lead to subsequent problems such as a reduced lifetime of structures and systems. In particular problems during the soft and post-exposure bake process can lead to an inhomogeneous distribution of material properties. This paper describes a novel approach for the characterization of SU-8 material properties in relation to a second epoxy-based material of different cross-linking by the measurement of optical dispersion within the material. A white-light interferometer was used. In particular the setup consisted of a white-light source, a Michelson-type interferometer and a spectrometer. The investigation of the dispersion characteristics was carried out by the detection of the equalization wavelength for different positions of the reference arm in a range from 400 to 900 nm. The measured time delay due to dispersion ranges from 850 to 1050 ps/m. For evaluation purposes a 200μm SU-8 sample was characterized in the described setup regarding its dispersion characteristics in relation to bulk epoxy material. The novel measurement approach allowed a fast and high-resolution material characterization for SU-8 micro structures which was suitable for integration in production lines. The outlook takes modifications of the experimental setup regarding on-wafer measurements into account.

  16. Genetic expression programming-based DBA for enhancing peer-assisted music-on-demand service in EPON

    Science.gov (United States)

    Liem, Andrew Tanny; Hwang, I.-Shyan; Nikoukar, AliAkbar; Lee, Jhong-Yue

    2015-03-01

    Today, the popularity of peer-assisted music-on-demand (MoD) has increased significantly worldwide. This service allows users to access large music library tracks, listen to music, and share their playlist with other users. Unlike the conventional voice traffic, such an application maintains music quality that ranges from 160 kbps to 320 kbps, which most likely consumes more bandwidth than other traffics. In the access network, Ethernet passive optical network (EPON) is one of the best candidates for delivering such a service because of being cost-effective and with high bandwidth. To maintain music quality, a stutter needs to be prevented because of either network effects or when the due user was not receiving enough resources to play in a timely manner. Therefore, in this paper, we propose two genetic expression programming (GEP)-based dynamic bandwidth allocations (DBAs). The first DBA is a generic DBA that aims to find an optimum formula for voice, video, and data services. The second DBA aims to find optimum formulas so that Optical Line Terminal (OLT) can satisfy not only the voice and Peer-to-Peer (P2P) MoD traffics but also reduce the stutter. Optical Network Unit (ONU) traits such as REPORT and GATE messages, cycle time, and mean packet delay are set to be predictor variables. Simulation results show that our proposed DBAs can satisfy the voice and P2P MoD services packet delay and monitor other overall system performances such as expedited forwarding (EF) jitter, packet loss, bandwidth waste, and system throughputs.

  17. Integración de las redes ópticas pasivas Ethernet EPON/GPON con la tecnología WiMAX . (Artículo)

    OpenAIRE

    Logroño Gómez, Jorge Israel

    2009-01-01

    El presente proyecto está orientado al estudio de las redes EPON/GPON y su integración con la tecnología WiMAX. Este artículo inicia con un estudio de las características generales sobre la Convergencia Fijo-Móvil (CFM), sus razones en este proceso de continuo cambio en las telecomunicaciones y de manera general las características del desarrollo de la tecnología WiMAX (Worldwide Interoperability for Microwave Access) como tecnología de acceso de banda ancha inalámbrica. Posteriormente se inc...

  18. Design and fabrication of an ac-electro-osmosis micropump with 3D high-aspect-ratio electrodes using only SU-8

    International Nuclear Information System (INIS)

    Rouabah, Hamza A; Morgan, Hywel; Green, Nicolas G; Park, Benjamin Y; Zaouk, Rabih B; Madou, Marc J

    2011-01-01

    Lab-on-a-chip devices require integrated pumping and fluid control in microchannels. A recently developed mechanism that can produce fluid flow is an integrated ac-electro-osmosis micropump. However, like most electrokinetic pumps, ac-electro-osmotic pumps are incapable of handling backpressure as the pumping force mechanism acts on the surface of the fluid rather than the bulk. This paper presents a novel 3D electrode structure designed to overcome this limitation. The electrodes are fabricated using carbon-MEMS technology based on the pyrolysis of the photo-patternable polymer SU-8. The novel ac-electro-osmosis micropump shows an increase in the flow velocity compared to planar electrodes.

  19. Optical Amplification at 1525 nm in BaYF5: 20% Yb3+, 2% Er3+ Nanocrystals Doped SU-8 Polymer Waveguide

    Directory of Open Access Journals (Sweden)

    Pengcheng Zhao

    2014-01-01

    Full Text Available We demonstrated optical amplification in BaYF5: 20% Yb3+, 2% Er3+ (BYF nanocrystals doped polymer waveguide. BYF nanocrystals with an average size of ∼13 nm were synthesized by a high-boiling solvent process. Intense 1.53 μm fluorescence was obtained in the nanocrystals under excitation at 980 nm. An optical polymer waveguide was fabricated by using BYF nanocrystals doped SU-8 polymer as the core material. A relative optical gain of ∼10.4 dB at 1525 nm was achieved in a 1.1 cm long waveguide for an input signal power of ∼0.09 mW and a pump power of ∼212 mW.

  20. Coleman-Weinberg symmetry breaking in SU(8) induced by a third rank antisymmetric tensor scalar field II: the fermion spectrum

    Science.gov (United States)

    Adler, Stephen L.

    2017-07-01

    We continue our study of Coleman-Weinberg symmetry breaking induced by a third rank antisymmetric tensor scalar, in the context of the SU(8) model (Adler 2014 Int. J. Mod. Phys. A 29 1450130) we proposed earlier. We focus in this paper on qualitative features that will determine whether the model can make contact with the observed particle spectrum. We discuss the mechanism for giving the spin \\frac{3}{2} field a mass by the BEH mechanism, and analyze the remaining massless spin \\frac{1}{2} fermions, the global chiral symmetries, and the running couplings after symmetry breaking. We note that the smallest gluon mass matrix eigenvalue has an eigenvector suggestive of U(1) B-L , and conjecture that the theory runs to an infrared fixed point at which there is a massless gluon with 3 to  -1 ratios in generator components. Assuming this, we discuss a mechanism for making contact with the standard model, based on a conjectured asymmetric breaking of Sp(4) to SU(2) subgroups, one of which is the electroweak SU(2), and the other of which is a ‘technicolor’ group that binds the original SU(8) model fermions, which play the role of ‘preons’, into composites. Quarks can emerge as 5 preon composites and leptons as 3 preon composites, with consequent stability of the proton against decay to a single lepton plus a meson. A composite Higgs boson can emerge as a two preon composite. Since anomaly matching for the relevant conserved global symmetry current is not obeyed by three fermion families, emergence of three composite families requires formation of a Goldstone boson with quantum numbers matching this current, which can be a light dark matter candidate.

  1. The emerging WDM EPON

    CERN Document Server

    Radivojević, Mirjana

    2017-01-01

    This book proposes dynamic wavelength and bandwidth allocation (DWBA), a hybrid of time-division multiplexing (TDM) and wavelength-division multiplexing (WDM), which offers a solution for service providers faced with multiservice networks. It discusses different models, architectures and implementations and evaluates their performance.

  2. Investigation of the air effect on the resonance frequency and damping of three small assembled structures using different adhesive materials (SU8 epoxy resin and compressed gold)

    International Nuclear Information System (INIS)

    Nouira, H; Foltête, E; Hirsinger, L; Ballandras, S

    2008-01-01

    There has been growing interest in recent years in the understanding of microsystems and the mechanical properties essential for their design. In this context, an experimental technique is proposed to characterize the structures of small dimensions composed of both silicon and lithium niobate and assembled using three different adhesive materials (SU8 (5 and 1 µm) and compressed gold) surrounded by various ambient air pressure levels. Dynamic tests were performed on three different structures used for the manufacturing of a harvesting energy microconverter. The assembled structure is mounted on a support and excited by a white noise signal via an electromagnetic shaker. The dynamic responses are recorded by a Doppler laser vibrometer and the modal parameters (obtained from the dynamic response) are identified in order to determine their evolution when the ambient air pressure inside the vacuum chamber is changed. A nonlinear modal identification is then performed. It is based on the logarithmic decrement method applied in the time–frequency domain using a wavelet transform of the time responses. The evolution of the equivalent modal frequencies and damping of the assembled structure versus time and vibration magnitude are identified for several pressure values ranging from a secondary vacuum to atmospheric pressure

  3. Tribo-functionalizing Si and SU8 materials by surface modification for application in MEMS/NEMS actuator-based devices

    International Nuclear Information System (INIS)

    Singh, R A; Satyanarayana, N; Sinha, S K; Kustandi, T S

    2011-01-01

    Micro/nano-electro-mechanical-systems (MEMS/NEMS) are miniaturized devices built at micro/nanoscales. At these scales, the surface/interfacial forces are extremely strong and they adversely affect the smooth operation and the useful operating lifetimes of such devices. When these forces manifest in severe forms, they lead to material removal and thereby reduce the wear durability of the devices. In this paper, we present a simple, yet robust, two-step surface modification method to significantly enhance the tribological performance of MEMS/NEMS materials. The two-step method involves oxygen plasma treatment of polymeric films and the application of a nanolubricant, namely perfluoropolyether. We apply the two-step method to the two most important MEMS/NEMS structural materials, namely silicon and SU8 polymer. On applying surface modification to these materials, their initial coefficient of friction reduces by ∼4-7 times and the steady-state coefficient of friction reduces by ∼2.5-3.5 times. Simultaneously, the wear durability of both the materials increases by >1000 times. The two-step method is time effective as each of the steps takes the time duration of approximately 1 min. It is also cost effective as the oxygen plasma treatment is a part of the MEMS/NEMS fabrication process. The two-step method can be readily and easily integrated into MEMS/NEMS fabrication processes. It is anticipated that this method will work for any kind of structural material from which MEMS/NEMS are or can be made.

  4. Tribo-functionalizing Si and SU8 materials by surface modification for application in MEMS/NEMS actuator-based devices

    Science.gov (United States)

    Singh, R. A.; Satyanarayana, N.; Kustandi, T. S.; Sinha, S. K.

    2011-01-01

    Micro/nano-electro-mechanical-systems (MEMS/NEMS) are miniaturized devices built at micro/nanoscales. At these scales, the surface/interfacial forces are extremely strong and they adversely affect the smooth operation and the useful operating lifetimes of such devices. When these forces manifest in severe forms, they lead to material removal and thereby reduce the wear durability of the devices. In this paper, we present a simple, yet robust, two-step surface modification method to significantly enhance the tribological performance of MEMS/NEMS materials. The two-step method involves oxygen plasma treatment of polymeric films and the application of a nanolubricant, namely perfluoropolyether. We apply the two-step method to the two most important MEMS/NEMS structural materials, namely silicon and SU8 polymer. On applying surface modification to these materials, their initial coefficient of friction reduces by ~4-7 times and the steady-state coefficient of friction reduces by ~2.5-3.5 times. Simultaneously, the wear durability of both the materials increases by >1000 times. The two-step method is time effective as each of the steps takes the time duration of approximately 1 min. It is also cost effective as the oxygen plasma treatment is a part of the MEMS/NEMS fabrication process. The two-step method can be readily and easily integrated into MEMS/NEMS fabrication processes. It is anticipated that this method will work for any kind of structural material from which MEMS/NEMS are or can be made.

  5. In situ SU-8 silver nanocomposites

    DEFF Research Database (Denmark)

    Fischer, Søren Vang; Uthuppu, Basil; Jakobsen, Mogens Havsteen

    2015-01-01

    Nanocomposite materials containing metal nanoparticles are of considerable interest in photonics and optoelectronics applications. However, device fabrication of such materials always encounters the challenge of incorporation of preformed nanoparticles into photoresist materials. As a solution to...

  6. Double layer resist process scheme for metal lift-off with application in inductive heating of microstructures

    DEFF Research Database (Denmark)

    Ouattara, Lassana; Knutzen, Michael; Keller, Stephan Urs

    2010-01-01

    We present a new method to define metal electrodes on top of high-aspect-ratio microstructures using standard photolithography equipment and a single chromium mask. A lift-off resist (LOR) layer is implemented in an SU-8 photolithography process to selectively remove metal at the end of the proce......We present a new method to define metal electrodes on top of high-aspect-ratio microstructures using standard photolithography equipment and a single chromium mask. A lift-off resist (LOR) layer is implemented in an SU-8 photolithography process to selectively remove metal at the end...

  7. On grand unified SU(8)sub(L)xSU(8)sub(R) model

    International Nuclear Information System (INIS)

    Pirogov, Yu.F.

    1980-01-01

    A set of general prjnciples justifying the choice of the group SU(N)sub(L)xSU(N)sub(R) with N=8 as the grand unified symmetry group is considered. Accordjng to these principles the group SU(N)sub(L)xSU(N)sub(R) is one of the most natural unified groups. Namely this group is maximum symmetry group of kinetic term of the Lagrangian of one family, which conserves fermion number. A new principle has been introduced according to which one of the manifestations of extended conformal invariance at small distances is mirror doubling of set of fermions, which is necessary on the other hand for renormalizability of the given unified model

  8. Application of Matrix Projection Exposure Using a Liquid Crystal Display Panel to Fabricate Thick Resist Molds

    Science.gov (United States)

    Fukasawa, Hirotoshi; Horiuchi, Toshiyuki

    2009-08-01

    The patterning characteristics of matrix projection exposure using an analog liquid crystal display (LCD) panel in place of a reticle were investigated, in particular for oblique patterns. In addition, a new method for fabricating practical thick resist molds was developed. At first, an exposure system fabricated in past research was reconstructed. Changes in the illumination optics and the projection lens were the main improvements. Using fly's eye lenses, the illumination light intensity distribution was homogenized. The projection lens was changed from a common camera lens to a higher-grade telecentric lens. In addition, although the same metal halide lamp was used as an exposure light source, the central exposure wavelength was slightly shortened from 480 to 450 nm to obtain higher resist sensitivity while maintaining almost equivalent contrast between black and white. Circular and radial patterns with linewidths of approximately 6 µm were uniformly printed in all directions throughout the exposure field owing to these improvements. The patterns were smoothly printed without accompanying stepwise roughness caused by the cell matrix array. On the bases of these results, a new method of fabricating thick resist molds for electroplating was investigated. It is known that thick resist molds fabricated using the negative resist SU-8 (Micro Chem) are useful because very high aspect patterns are printable and the side walls are perpendicular to the substrate surfaces. However, the most suitable exposure wavelength of SU-8 is 365 nm, and SU-8 is insensitive to light of 450 nm wavelength, which is most appropriate for LCD matrix exposure. For this reason, a novel multilayer resist process was proposed, and micromolds of SU-8 of 50 µm thickness were successfully obtained. As a result, feasibility for fabricating complex resist molds including oblique patterns was demonstrated.

  9. 基于EPON的池州配电通信网综合管理系统设计与实现%Design and Implementation of the Integrated Management System of Chizhou Distribution Communication Network Based on EPON Technology

    Institute of Scientific and Technical Information of China (English)

    江龙才; 霍朝辉; 步冬静

    2016-01-01

    Distribution communication networks have many characteristics, such as wide distribution, a number of terminal nodes, various types of bearer services, multiple access technology of mixed applications and the bad running scene environment, which may cause lots of problem, such as diversiifed technology standards, too many equipment manufacturers and complex network structures.These problems make the scheduling and management of distribution communication networks inconvenient.Because of the present situation of Chizhou power supply company, this paper puts forward management requirements of distribution communication networks based on its existing technology and architectures.This paper also designs and develops a comprehensive network management prototype system based on EPON technology.The management requirements and comprehensive network management prototype system can manage distribution communication networks effectively and improve its availability.%配用电通信网具有分布广泛、终端节点众多、承载业务类型丰富多样、多种接入技术混合应用、现场运行环境恶劣等特点,导致配用电通信网存在技术制式多样化、设备厂家众多、组网结构复杂等问题,不便于管理和调度。文章基于池州供电公司现状,在现有配用电通信网技术及体系架构的基础上,提出配用电通信网的管理需求,基于EPON设计并研发了配用电通信综合网管原型系统,以便能够有效地管理配用电通信网络,提高配用电通信网的可用率。

  10. Resist materials for proton micromachining

    International Nuclear Information System (INIS)

    Kan, J.A. van; Sanchez, J.L.; Xu, B.; Osipowicz, T.; Watt, F.

    1999-01-01

    The production of high aspect ratio microstructures is a potential growth area. The combination of deep X-ray lithography with electroforming and micromolding (i.e. LIGA) is one of the main techniques used to produce 3D microstructures. The new technique of proton micromachining employs focused MeV protons in a direct write process which is complementary to LIGA, e.g. micromachining with 2 MeV protons results in microstructures with a height of 63 μm and lateral sub-micrometer resolution in PMMA resist. The aim of this paper is to investigate the capabilities of proton micromachining as a lithographic technique. This involves the study of different types of resists. The dose distribution of high molecular weight PMMA is compared with three other types of resist: First the positive photo resist AZ P4620 will be discussed and then PMGI SF 23, which can be used as a deep UV, e-beam or X-ray resist. Finally SU-8, a new deep UV negative type of chemically amplified resist will be discussed. All these polymers are applied using the spin coating technique at thicknesses of between 1 and 36 μm

  11. Proton beam micromachining on strippable aqueous base developable negative resist

    International Nuclear Information System (INIS)

    Rajta, I.; Uzonyi, I.; Baradacs, E.; Chatzichristidi, M.; Raptis, I.; Valamontes, E.S.

    2004-01-01

    Complete text of publication follows. Proton Beam Micromachining (PBM, also known as P-beam writing), a novel direct- write process for the production of 3D microstructures, can be used to make multilevel structures in a single layer of resist by varying the ion energy. The interaction between the bombarding ions and the target material is mainly ionization, and very few ions suffer high angle nuclear collisions, therefore structures made with PBM have smooth near vertical side walls. The most commony applied resists in PBM are the positive, conventional, polymethyl methacrylate (PMMA); and the negative, chemically amplified, SU-8 (Micro Chem Corp). SU-8 is an epoxy based resist suitable also for LIGA and UV-LIGA processes, it offers good sensitivity, good process latitude, very high aspect ratio and therefore it dominates in the high aspect ratio micromachining applications. SU-8 requires 30 nC/mm 2 fluence for PBM irradiations at 2 MeV protons. Its crosslinking chemistry is based on the eight epoxy rings in the polymer chain, which provide a very dense three dimensional network in the presence of suitably activated photo acid generators (PAGs) which is very difficult to be stripped away after development. Thus, stripping has to be assisted with plasma processes or with special liquid removers. Moreover, the SU-8 developer is organic, propylene glycol methyl ether acetate (PGMEA), and thus environmentally non-friendly. To overcome the SU-8 stripping limitations, design of a negative resist system where solubility change is not based solely on cross- linking but also on the differentiation of hydrophilicity between exposed and non-exposed areas is desirable. A new resist formulation, fulfilling the above specifications has been developed recently [1]. This formulation is based on a specific grade epoxy novolac (EP) polymer, a partially hydrogenated poly-4-hydroxy styrene (PHS) polymer, and an onium salt as photoacid generator (PAG), and has been successfully

  12. Simulation of SU-8 frequency-driven scratch drive actuators

    KAUST Repository

    Conchouso Gonzalez, David

    2013-04-01

    This paper presents the simulation of Scratch Drive Actuators (SDAs) for micro-robotic applications. SDAs use electrostatic forces to generate motion on top of an interdigitated electrode array. The purpose of this investigation is to evaluate several design geometries and micro-actuator configurations using ConventorWare®\\'s finite element analysis module. The study performed investigates the SDAs modal and electrostatic behavior and the effects of linking two or more SDAs together in a microrobot device. In addition, the interdigitated electrode array performance, used for power delivery, was studied by changing the thickness of its dielectric layer. We present our observations based on these studies, which will aid in the understanding and development of future SDA designs. © 2013 IEEE.

  13. Simulation of SU-8 frequency-driven scratch drive actuators

    KAUST Repository

    Conchouso Gonzalez, David; Carreno, Armando Arpys Arevalo; Castro, David; Al Rawashdeh, Ehab Jamal; Valencia Garcia, Manuel; Zaher, Amir Omar; Kosel, Jü rgen; Foulds, Ian G.

    2013-01-01

    This paper presents the simulation of Scratch Drive Actuators (SDAs) for micro-robotic applications. SDAs use electrostatic forces to generate motion on top of an interdigitated electrode array. The purpose of this investigation is to evaluate several design geometries and micro-actuator configurations using ConventorWare®'s finite element analysis module. The study performed investigates the SDAs modal and electrostatic behavior and the effects of linking two or more SDAs together in a microrobot device. In addition, the interdigitated electrode array performance, used for power delivery, was studied by changing the thickness of its dielectric layer. We present our observations based on these studies, which will aid in the understanding and development of future SDA designs. © 2013 IEEE.

  14. SU-8 photoresist-derived electrospun carbon nanofibres as high ...

    Indian Academy of Sciences (India)

    2017-06-09

    Jun 9, 2017 ... as high-capacity anode material for lithium ion battery. M KAKUNURI, S KAUSHIK, A SAINI and C S SHARMA. ∗. Creative and Advanced Research Based On Nanomaterials (CARBON) Laboratory, Department of Chemical Engineering,. Indian Institute of Technology, Hyderabad, Kandi 502285, India. ∗.

  15. SU-8 Cantilever Sensor with Integrated Read-Out

    DEFF Research Database (Denmark)

    Johansson, Alicia Charlotte

    2007-01-01

    Cantilever baserede biosensorer kan bruges til så kaldet label-free detektion af små koncentrationer af molekyler i en opløsning. Når et specifikt molekyle binder til overfladen af en cantilever induceres et overfladestress som resulterer i en udbøjning af cantileveren. Cantileverens udbøjningen ...

  16. Proton beam micromachined buried microchannels in negative tone resist materials

    International Nuclear Information System (INIS)

    Rajta, I.; Chatzichristidi, M.; Baradacs, E.; Cserhati, C.; Raptis, I.; Manoli, K.; Valamontes, E.S.

    2007-01-01

    In the present work the Atomki, Debrecen microprobe facility has been used to write long tilted structures by 2 MeV protons. For the formation of the structures, two exposures have been carried out at +20 o and -20 o using a goniometer stage sample holder. The tilted structures were resolved in the negative tone resist materials SU-8 and ADEPR (an aqueous base developable chemically amplified resist). The length of the microchannels was varied between 100 μm and 1000 μm, the wall thickness was less than 10 μm. By applying the developed methodology it was possible to resolve the desired layout through the whole length of the channel

  17. Resist materials for proton beam writing: A review

    Energy Technology Data Exchange (ETDEWEB)

    Kan, J.A. van, E-mail: phyjavk@nus.edu.sg [Centre for Ion Beam Applications, Physics Department, 2 Science Drive 3, National University of Singapore, 117542 Singapore (Singapore); Malar, P. [Research Institute, SRM University, Kattankulathur, Chennai 603203 (India); Wang, Y.H. [Centre for Ion Beam Applications, Physics Department, 2 Science Drive 3, National University of Singapore, 117542 Singapore (Singapore)

    2014-08-15

    Highlights: • PBW can now achieve 19 nm details in HSQ and 65 nm in PMMA. • A complete table of resist materials for PBW has been presented, including minimum feature size, achievable aspect ratio, suitability for electroplating and where available contrast of the resist. • PBW fabricated molds can now be used for single DNA molecule detection, single DNA manipulation and large scale Genome mapping. - Abstract: Proton beam writing (PBW) is a lithographic technique that has been developed since the mid 1990s, initially in Singapore followed by several groups around the world. MeV protons while penetrating materials will maintain a practically straight path. During the continued slowing down of a proton in material it will mainly interact with substrate electrons and transfer a small amount of energy to each electron, the induced secondary electrons will modify the molecular structure of resist within a few nanometers around the proton track. The recent demonstration of high aspect ratio sub 20 nm lithography in HSQ shows the potential of PBW. To explore the full capabilities of PBW, the understanding of the interaction of fast protons with different resist materials is important. Here we give an update of the growing number of resist materials that have been evaluated for PBW. In particular we evaluate the exposure and development strategies for the most promising resist materials like PMMA, HSQ, SU-8 and AR-P and compare their characteristics with respect to properties such as contrast and sensitivity. Besides an updated literature survey we also present new findings on AR-P and PMGI resists. Since PBW is a direct write technology it is important to look for fast ways to replicate micro and nanostructures. In this respect we will discuss the suitability and performance of several resists for Ni electroplating for mold fabrication in nano imprint technologies. We will summarize with an overview of proton resist characteristics like sensitivity, contrast

  18. Resist materials for proton beam writing: A review

    International Nuclear Information System (INIS)

    Kan, J.A. van; Malar, P.; Wang, Y.H.

    2014-01-01

    Highlights: • PBW can now achieve 19 nm details in HSQ and 65 nm in PMMA. • A complete table of resist materials for PBW has been presented, including minimum feature size, achievable aspect ratio, suitability for electroplating and where available contrast of the resist. • PBW fabricated molds can now be used for single DNA molecule detection, single DNA manipulation and large scale Genome mapping. - Abstract: Proton beam writing (PBW) is a lithographic technique that has been developed since the mid 1990s, initially in Singapore followed by several groups around the world. MeV protons while penetrating materials will maintain a practically straight path. During the continued slowing down of a proton in material it will mainly interact with substrate electrons and transfer a small amount of energy to each electron, the induced secondary electrons will modify the molecular structure of resist within a few nanometers around the proton track. The recent demonstration of high aspect ratio sub 20 nm lithography in HSQ shows the potential of PBW. To explore the full capabilities of PBW, the understanding of the interaction of fast protons with different resist materials is important. Here we give an update of the growing number of resist materials that have been evaluated for PBW. In particular we evaluate the exposure and development strategies for the most promising resist materials like PMMA, HSQ, SU-8 and AR-P and compare their characteristics with respect to properties such as contrast and sensitivity. Besides an updated literature survey we also present new findings on AR-P and PMGI resists. Since PBW is a direct write technology it is important to look for fast ways to replicate micro and nanostructures. In this respect we will discuss the suitability and performance of several resists for Ni electroplating for mold fabrication in nano imprint technologies. We will summarize with an overview of proton resist characteristics like sensitivity, contrast

  19. Antimicrobial Resistance

    Science.gov (United States)

    ... least 10 countries (Australia, Austria, Canada, France, Japan, Norway, Slovenia, South Africa, Sweden and the United Kingdom ... plan Global report on surveillance Country situation analysis Policy to combat antimicrobial resistance More on antimicrobial resistance ...

  20. Antimicrobial Resistance

    Science.gov (United States)

    ... can prevent and manage antimicrobial resistance. It is collaborating with partners to strengthen the evidence base and ... on the global action plan. WHO has been leading multiple initiatives to address antimicrobial resistance: World Antibiotic ...

  1. Antibiotic resistance

    Directory of Open Access Journals (Sweden)

    Marianne Frieri

    2017-07-01

    Full Text Available Summary: Antimicrobial resistance in bacterial pathogens is a challenge that is associated with high morbidity and mortality. Multidrug resistance patterns in Gram-positive and -negative bacteria are difficult to treat and may even be untreatable with conventional antibiotics. There is currently a shortage of effective therapies, lack of successful prevention measures, and only a few new antibiotics, which require development of novel treatment options and alternative antimicrobial therapies. Biofilms are involved in multidrug resistance and can present challenges for infection control. Virulence, Staphylococcus aureus, Clostridium difficile infection, vancomycin-resistant enterococci, and control in the Emergency Department are also discussed. Keywords: Antibiotic resistance, Biofilms, Infections, Public health, Emergency Department

  2. Downstream-based Scheduling for Energy Conservation in Green EPONs

    KAUST Repository

    Chen, Shen; Dhaini, Ahmad R.; Ho, Pin-Han; Shihada, Basem; Shen, Gangxiang; Lin, Chih-Hao

    2012-01-01

    the ONU sleep time, it jeopardizes the quality of service (QoS) performance of the network, especially for downstream traffic in case the overlapping is based on the upstream time slot. In this paper, we study the downstream traffic performance in green

  3. Resistant Hypertension.

    Science.gov (United States)

    Doroszko, Adrian; Janus, Agnieszka; Szahidewicz-Krupska, Ewa; Mazur, Grzegorz; Derkacz, Arkadiusz

    2016-01-01

    Resistant hypertension is a severe medical condition which is estimated to appear in 9-18% of hypertensive patients. Due to higher cardiovascular risk, this disorder requires special diagnosis and treatment. The heterogeneous etiology, risk factors and comorbidities of resistant hypertension stand in need of sophisticated evaluation to confirm the diagnosis and select the best therapeutic options, which should consider lifestyle modifications as well as pharmacological and interventional treatment. After having excluded pseudohypertension, inappropriate blood pressure measurement and control as well as the white coat effect, suspicion of resistant hypertension requires an analysis of drugs which the hypertensive patient is treated with. According to one definition - ineffective treatment with 3 or more antihypertensive drugs including diuretics makes it possible to diagnose resistant hypertension. A multidrug therapy including angiotensin - converting enzyme inhibitors, angiotensin II receptor blockers, beta blockers, diuretics, long-acting calcium channel blockers and mineralocorticoid receptor antagonists has been demonstrated to be effective in resistant hypertension treatment. Nevertheless, optional, innovative therapies, e.g. a renal denervation or baroreflex activation, may create a novel pathway of blood pressure lowering procedures. The right diagnosis of this disease needs to eliminate the secondary causes of resistant hypertension e.g. obstructive sleep apnea, atherosclerosis and renal or hormonal disorders. This paper briefly summarizes the identification of the causes of resistant hypertension and therapeutic strategies, which may contribute to the proper diagnosis and an improvement of the long term management of resistant hypertension.

  4. Camptothecin resistance

    DEFF Research Database (Denmark)

    Brangi, M; Litman, Thomas; Ciotti, M

    1999-01-01

    . Glucuronides were found at equal levels in both parental and resistant colon cancer cell lines for epirubicin and to a lesser extent for SN-38 and mitoxantrone. Low levels of glucuronidation could also be detected in the resistant breast cancer cells. These results were confirmed by analysis of the UGT1A...

  5. Antibiotic Resistance

    DEFF Research Database (Denmark)

    Munck, Christian

    morbidity and mortality as well as an increase in the cost of treatment. Understanding how bacteria respond to antibiotic exposure gives the foundations for a rational approach to counteract antimicrobial resistance. In the work presented in this thesis, I explore the two fundamental sources...... of antimicrobial resistance: (1) adaptive mutations and (2) horizontal acquisition of resistance genes from antibiotic gene reservoirs. By studying the geno- and phenotypic changes of E. coli in response to single and drug-pair exposures, I uncover the evolutionary trajectories leading to adaptive resistance. I...... to rationally design drug combinations that limit the evolution of antibiotic resistance due to counteracting evolutionary trajectories. My results highlight that an in-depth knowledge about the genetic responses to the individual antimicrobial compounds enables the prediction of responses to drug combinations...

  6. Antimicrobial Resistance

    Science.gov (United States)

    ... past two decades due to the increase in immunocompromised and elderly patients, increasing use of invasive indwelling ... aureus developing resistance to vancomycin, a very powerful antibiotic prescribed for the most intractable bacterial infections. In ...

  7. Drug Resistance

    Science.gov (United States)

    ... Drug-resistance testing is also recommended for all pregnant women with HIV before starting HIV medicines and also in some pregnant women already taking HIV medicines. Pregnant women will work with their health ...

  8. Antimicrobial resistance

    DEFF Research Database (Denmark)

    Llor, Carl; Bjerrum, Lars

    2014-01-01

    Antimicrobial resistance is a global public health challenge, which has accelerated by the overuse of antibiotics worldwide. Increased antimicrobial resistance is the cause of severe infections, complications, longer hospital stays and increased mortality. Overprescribing of antibiotics......-the-counter sale of antibiotics, the use of antimicrobial stewardship programmes, the active participation of clinicians in audits, the utilization of valid rapid point-of-care tests, the promotion of delayed antibiotic prescribing strategies, the enhancement of communication skills with patients with the aid...

  9. Resistant hypertension.

    Science.gov (United States)

    Wei, Fang-Fei; Zhang, Zhen-Yu; Huang, Qi-Fang; Yang, Wen-Yi; Staessen, Jan A

    2018-06-15

    The publication of the first non-randomised proof-of-concept trial of renal denervation as a treatment modality in treatment-resistant hypertension set the stage for a search for novel devices with the expectation that technology would reduce the burden of hypertension by reducing or eliminating the costly and lifelong use of blood pressure lowering medications. As we demonstrate in this review, this idea so attractive to manufacturers and invasive cardiologists and radiologists overlooked decades of careful pathophysiological research in a disease, which still remains enigmatic but remains the major cause of cardiovascular mortality worldwide. To make our point, we first reviewed the prevalence and risks associated with treatment-resistant hypertension. Next, we highlighted the key points required for the diagnosis of treatment-resistant hypertension, including the recording of the ambulatory blood pressure and the assessment of adherence to medication. Finally, we summarised new insights in the management of treatment-resistant hypertension by medication and devices and in the future research. Throughout our review, we focused on new evidence became available since 2013. Our conclusion is that optimising medical treatment based on simple algorithms remains the state of the art in treatment-resistant hypertension.

  10. Anticoagulant Resistance

    DEFF Research Database (Denmark)

    Heiberg, Ann-Charlotte

    Although sewer rat control is carried out in more than 80 % of all Danish municipalities, with usage of large amounts of anticoagulant rodenticides, knowledge on anticoagulant resistance among rats living in the sewers is limited. As rat problems in urban areas are believed to be related to sewer...... problems (70-90 % in UK and DK) unawareness of resistance amongst these populations of Brown rats may constitute a future control problem and knowledge on this issue has become crucial. Rats were captured in sewers from seven different locations in the suburban area of Copenhagen. Locations was chosen...... to represent different sewer rat management strategies i) no anticoagulants for approx. 20 years ii) no anticoagulants for the last 5 years and iii) continuous control for many years. Animals were tested for resistance to bromadiolone by Blood-Clotting Response test, as bromadiolone is the most frequently used...

  11. Reducing Resistance

    DEFF Research Database (Denmark)

    Lindell, Johanna

    care may influence decisions on antibiotic use. Based on video-and audio recordings of physician-patient consultations it is investigated how treatment recommendations are presented, can be changed, are forecast and explained, and finally, how they seemingly meet resistance and how this resistance......Antibiotic resistance is a growing public health problem both nationally and internationally, and efficient strategies are needed to reduce unnecessary use. This dissertation presents four research studies, which examine how communication between general practitioners and patients in Danish primary...... is responded to.The first study in the dissertation suggests that treatment recommendations on antibiotics are often done in a way that encourages patient acceptance. In extension of this, the second study of the dissertation examines a case, where acceptance of such a recommendation is changed into a shared...

  12. Drug resistance

    NARCIS (Netherlands)

    Gorter, J.A.; Potschka, H.; Noebels, J.L.; Avoli, M.; Rogawski, M.A.; Olsen, R.W.; Delgado-Escueta, A.V.

    2012-01-01

    Drug resistance remains to be one of the major challenges in epilepsy therapy. Identification of factors that contribute to therapeutic failure is crucial for future development of novel therapeutic strategies for difficult-to-treat epilepsies. Several clinical studies have shown that high seizure

  13. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... video) Animation of Antimicrobial Resistance (text version) Arabic Translation of Animation of Antimicrobial Resistance Chinese Translation of Animation of Antimicrobial Resistance French Translation of ...

  14. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More sharing options ... of Animation of Antimicrobial Resistance More in Antimicrobial ... Antimicrobial Resistance Monitoring System About NARMS 2015 NARMS Integrated ...

  15. Dielectric properties of ligand-modified gold nanoparticles/SU-8 photopolymer based nanocomposites

    KAUST Repository

    Toor, Anju; So, Hongyun; Pisano, Albert P.

    2017-01-01

    This article reports the enhanced dielectric properties of a photodefinable nanocomposite material containing sub–10 nm coated metal nanoparticles (NPs). The surface morphology of the synthesized dodecanethiol-functionalized gold NPs was characterized using the transmission electron microscopy (TEM). We investigated the particle agglomeration and dispersion during the various stages of the nanocomposite synthesis using TEM. Physical properties such as dielectric permittivity and dielectric loss were measured experimentally. The dependence of dielectric permittivity and loss tangent on particle concentration and frequency was studied. Nanocomposite films showed an approximately three times enhancement in average dielectric constant over the polymer base value and an average dielectric loss of 0.09 at 1 kHz, at a filler loading of 10% w/w.

  16. Simulation of a low frequency Z-axis SU-8 accelerometer in coventorware and MEMS+

    KAUST Repository

    Carreno, Armando Arpys Arevalo; Conchouso Gonzalez, David; Zaher, Amir Omar; Foulds, Ian G.; Kosel, Jü rgen

    2013-01-01

    calculation, and a comparison of results achieved using CoventorWare® ANALYZER™ and MEMS+®. A fabricated energy harvester design from [1] was used for modeling and simulation in this study, with a four spring attachment of a 650μm×650μm; ×110μm proof mass of 4.542

  17. Dielectric properties of ligand-modified gold nanoparticles/SU-8 photopolymer based nanocomposites

    KAUST Repository

    Toor, Anju

    2017-04-15

    This article reports the enhanced dielectric properties of a photodefinable nanocomposite material containing sub–10 nm coated metal nanoparticles (NPs). The surface morphology of the synthesized dodecanethiol-functionalized gold NPs was characterized using the transmission electron microscopy (TEM). We investigated the particle agglomeration and dispersion during the various stages of the nanocomposite synthesis using TEM. Physical properties such as dielectric permittivity and dielectric loss were measured experimentally. The dependence of dielectric permittivity and loss tangent on particle concentration and frequency was studied. Nanocomposite films showed an approximately three times enhancement in average dielectric constant over the polymer base value and an average dielectric loss of 0.09 at 1 kHz, at a filler loading of 10% w/w.

  18. A Multimodal, SU-8 - Platinum - Polyimide Microelectrode Array for Chronic In Vivo Neurophysiology.

    Directory of Open Access Journals (Sweden)

    Gergely Márton

    Full Text Available Utilization of polymers as insulator and bulk materials of microelectrode arrays (MEAs makes the realization of flexible, biocompatible sensors possible, which are suitable for various neurophysiological experiments such as in vivo detection of local field potential changes on the surface of the neocortex or unit activities within the brain tissue. In this paper the microfabrication of a novel, all-flexible, polymer-based MEA is presented. The device consists of a three dimensional sensor configuration with an implantable depth electrode array and brain surface electrodes, allowing the recording of electrocorticographic (ECoG signals with laminar ones, simultaneously. In vivo recordings were performed in anesthetized rat brain to test the functionality of the device under both acute and chronic conditions. The ECoG electrodes recorded slow-wave thalamocortical oscillations, while the implanted component provided high quality depth recordings. The implants remained viable for detecting action potentials of individual neurons for at least 15 weeks.

  19. Insulin Resistance

    DEFF Research Database (Denmark)

    Jensen, Benjamin Anderschou Holbech

    Insulin resistance (IR) is escalating with alarming pace and is no longer restricted to westernized countries. As a forerunner for some of the most serious threats to human health including metabolic syndrome, cardiovascular diseases, and type 2-diabetes, the need for new treatment modalities...... interventions. We further show that improving the inflammatory toning, using fish oil as fat source, protects mice against diet induced obesity and -inflammation while preserving insulin sensitivity, even in the absence of free fatty acid receptor 4. Conversely, HFD-induced intestinal dysbiosis is associated...

  20. Resistance welding

    DEFF Research Database (Denmark)

    Bay, Niels; Zhang, Wenqi; Rasmussen, Mogens H.

    2003-01-01

    Resistance welding comprises not only the well known spot welding process but also more complex projection welding operations, where excessive plastic deformation of the weld point may occur. This enables the production of complex geometries and material combinations, which are often not possible...... to weld by traditional spot welding operations. Such joining processes are, however, not simple to develop due to the large number of parameters involved. Development has traditionally been carried out by large experimental investigations, but the development of a numerical programme system has changed...... this enabling prediction of the welding performance in details. The paper describes the programme in short and gives examples on industrial applications. Finally investigations of causes for failure in a complex industrial joint of two dissimilar metals are carried out combining numerical modelling...

  1. Antibiotic Resistance

    DEFF Research Database (Denmark)

    Hansen, Malene Plejdrup; Hoffmann, Tammy C; McCullough, Amanda R

    2015-01-01

    hygiene, and possibly vaccination and exercise, may be effective. Also, a large range of complementary and alternative medicines (e.g. zinc, vitamin C and probiotics) are proposed for preventing and treating ARIs, but evidence for efficacy is scarce. General practitioners' (GPs) attitudes towards...... wrong. Shared decision making might be a solution, as it enables clinician and patient to participate jointly in making a health decision, having discussed the options together with the evidence for their harms as well as benefits. Furthermore, GPs' diagnostic uncertainty - often leading...... will greatly improve the use of antibiotics for ARIs. However, used in concert, combinations are likely to enable clinicians and health care systems to implement the strategies that will reduce antimicrobial resistance in the future....

  2. Resisting dehumanization

    DEFF Research Database (Denmark)

    Lassen, Inger Marie

    2018-01-01

    Recent years have seen an increase in the influx of asylum-seekers in Scandinavia, and in Denmark this has led to ever-tighter immigration control. This article discusses emerging practices of refugee solidarity and resistance to hegemonic migration policy in Danish civil society in the wake...... of what has been referred to as the European refugee crisis. It further reflects upon what it means to be a Danish citizen facing the dilemma of law-abiding conduct versus human decency, in line with what Foucault (1983) referred to as ‘ethical self-formation’. This is illustrated through a case study...... of an incident from September 2015, when a member of a Danish City Council offered private shelter to immigrants who were on their way to Norway. The incident led to legal proceedings in August 2016 for what the defendant referred to as ‘the offense of helping fellow human beings in need’. The study is informed...

  3. Electrical resistivity measurements to predict abrasion resistance

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 31; Issue 2. Electrical resistivity measurements to predict abrasion resistance of rock aggregates ... It was seen that correlation coefficients were increased for the rock classes. In addition ...

  4. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More sharing options ... CVM) produced a nine-minute animation explaining how antimicrobial resistance both emerges and proliferates among bacteria. Over time, ...

  5. Combating Antibiotic Resistance

    Science.gov (United States)

    ... Bacteria Phasing Out Certain Antibiotic Use in Farm Animals FDA: Cutting-Edge Technology Sheds Light on Antibiotic Resistance For More Information Antibiotics and Antibiotic Resistance Antimicrobial Resistance Information for Consumers and Health Professionals CDC: ...

  6. Hydraulic resistance of biofilms

    KAUST Repository

    Dreszer, C.; Vrouwenvelder, Johannes S.; Paulitsch-Fuchs, Astrid H.; Zwijnenburg, Arie; Kruithof, Joop C.; Flemming, Hans Curt

    2013-01-01

    resistance is very low compared to the expected biofilm resistance and, thus, biofilm resistance can be determined accurately. Transmembrane pressure drop was monitored. As biofilm parameters, thickness, total cell number, TOC, and extracellular polymeric

  7. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More sharing options ... produced a nine-minute animation explaining how antimicrobial resistance both emerges and proliferates among bacteria. Over time, ...

  8. HIV Resistance Testing

    Science.gov (United States)

    ... 14, 2016 Select a Language: Fact Sheet 126 HIV Resistance Testing WHAT IS RESISTANCE? HOW DOES RESISTANCE ... ARVs. If you miss doses of your medications, HIV will multiply more easily. More mutations will occur. ...

  9. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More sharing ... CVM) produced a nine-minute animation explaining how antimicrobial resistance both emerges and proliferates among bacteria. Over ...

  10. Induced resistance: an enhancement of basal resistance?

    NARCIS (Netherlands)

    Vos, M. de; Robben, C.; Pelt, J.A. van; Loon, L.C. van; Pieterse, C.M.J.

    2002-01-01

    Upon primary pathogen attack, plants activate resistance mechanisms at the site of infection. Besides this so-called basal resistance, plants have also the ability to enhance their defensive capacity against future pathogen attack. There are at least two types of biologically induced resistance.

  11. Animation of Antimicrobial Resistance

    Science.gov (United States)

    ... Animal & Veterinary Cosmetics Tobacco Products Animal & Veterinary Home Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin ...

  12. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Animal & Veterinary Cosmetics Tobacco Products Animal & Veterinary Home Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin ...

  13. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... More in Antimicrobial Resistance National Antimicrobial Resistance Monitoring System ... If you need help accessing information in different file formats, see Instructions for Downloading ...

  14. Resistance to Powdery Mildews

    DEFF Research Database (Denmark)

    Siwoszek, Agnieszka Izabela

    in majority of them. Resistance to barley powdery mildew in the field is controlled by use of resistant varieties in a combination with fungicides. Early disease management is crucial for effective control. Yet, the pathogen commonly develops fungicide resistance due to simple point mutations. Several studies...... protection. In the present study, I provide an overview of the current knowledge about plant pathogens and plant disease resistance. I use Arabidopsis as a model to investigate the mechanism of non-host resistance, presumed to be the most durable and broad-spectrum form of resistance. I attempt to determine...

  15. Oxidation-resistant cermet

    Science.gov (United States)

    Phillips, W. M.

    1977-01-01

    Chromium metal alloys and chromium oxide ceramic are combined to produce cermets with oxidation-resistant properties. Application of cermets includes use in hot corrosive environments requiring strong resistive materials.

  16. Resistance seam welding

    International Nuclear Information System (INIS)

    Schueler, A.W.

    1977-01-01

    The advantages and disadvantages of the resistance seam welding process are presented. Types of seam welds, types of seam welding machines, seam welding power supplies, resistance seam welding parameters and seam welding characteristics of various metals

  17. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... how antimicrobial resistance both emerges and proliferates among bacteria. Over time, the use of antimicrobial drugs will result in the development of resistant strains of bacteria, complicating clinician's efforts to select the appropriate antimicrobial ...

  18. Electrical Methods: Resistivity Methods

    Science.gov (United States)

    Surface electrical resistivity surveying is based on the principle that the distribution of electrical potential in the ground around a current-carrying electrode depends on the electrical resistivities and distribution of the surrounding soils and rocks.

  19. Insulin Resistance and Prediabetes

    Science.gov (United States)

    ... Your Baby is Born Monogenic Diabetes Insulin Resistance & Prediabetes Insulin resistance and prediabetes occur when your body ... will stay in the healthy range. What is prediabetes? Prediabetes means your blood glucose levels are higher ...

  20. Antimicrobial (Drug) Resistance

    Science.gov (United States)

    ... with facebook share with twitter share with linkedin Antimicrobial (Drug) Resistance Go to Information for Researchers ► Credit: ... and infectious diseases. Why Is the Study of Antimicrobial (Drug) Resistance a Priority for NIAID? Over time, ...

  1. CONFERENCE REPORT ANTIRETROVIRAL RESISTANCE

    African Journals Online (AJOL)

    2004-08-02

    Aug 2, 2004 ... development of new agents with potential clinical utility for treating resistant ... data on the emergence of resistance among Thai women given zidovudine ... had achieved full virological suppression (viral load. < 50 copies/ml).

  2. Resistance to Linezolid

    DEFF Research Database (Denmark)

    Vester, Birte; Ntokou, Eleni

    2017-01-01

    Linezolid is an antimicrobial agent that binds to the bacterial ribosome and thereby inhibits protein synthesis. Soon after its release as a clinical drug, it became clear that bacteria could become resistant to linezolid. The resistance mechanisms are mainly causing alteration of the drug target...... site, but probably efflux might also play a role. The resistance is still rare in surveillance studies, but outbreaks of resistant clones from hospitals have been observed. So far the main mechanisms of resistance are occurrence of mutations in ribosomal genes or obtaining plasmids with a gene coding...... for a methyltransferase providing resistance. The most obvious way to avoid resistance may be development of derivatives of linezolid overcoming the known resistance mechanisms....

  3. Resisting Organizational Change

    OpenAIRE

    Andersson, Gunnar

    2015-01-01

    We are continuously reminded of how change induces controversy and resistance, regardless of support. We repeatedly experience resistance in difficulties of implementation, little progress, and poor results, rather than increased productivity as anticipated. In a detailed account of how change plays out, a mosaic of what resistance looks like emerges. The picture is both familiar and absolutely concrete, and challenges the structural assumptions and dichotomies on support and resistance in an...

  4. Antibiotic resistance reservoirs

    NARCIS (Netherlands)

    Versluis, Dennis

    2016-01-01

    One of the major threats to human health in the 21st century is the emergence of pathogenic bacteria that are resistant to multiple antibiotics, thereby limiting treatment options. An important route through which pathogens become resistant is via acquisition of resistance genes from

  5. Resisting Mind Control.

    Science.gov (United States)

    Anderson, Susan M.; Zimbardo, Philip G.

    1980-01-01

    Provides conceptual analyses of mind control techniques along with practical advice on how to resist these techniques. The authors stress that effective mind control stems more from everyday social relations than from exotic technological gimmicks. Suggestions are given for resisting persuasion, resisting systems, and challenging the system.…

  6. Engineering and Characterizing Light-Matter Interactions in Photonic Crystals

    Science.gov (United States)

    2010-01-01

    SU8 monomer has, on average, eight epoxy groups, that under go a ring-opening polymerization in the presence of an acid catalyst. SU8 falls into...copper oxide [49] into colloidal and SU8 polymer photonic crystal templates, respectively. 1.5.2 Gas-Phase Infilling Gas-phase deposition typically...resist using direct laser writing. 78 Figure 2. Scanning electron micrograph of an over- polymerized woodpile structure fabricated in SU8 photo-resist

  7. Integrated Active and Passive Polymer Optical Components with nm to mm Features

    DEFF Research Database (Denmark)

    Christiansen, Mads Brøkner; Schøler, Mikkel; Kristensen, Anders

    2007-01-01

    We present wafer-scale fabrication of integrated active and passive polymer optics with nm to mm features. First order DFB lasers, defined in dye doped SU-8 resist are integrated with SU-8 waveguides.......We present wafer-scale fabrication of integrated active and passive polymer optics with nm to mm features. First order DFB lasers, defined in dye doped SU-8 resist are integrated with SU-8 waveguides....

  8. Challenges to Resistance Welding

    DEFF Research Database (Denmark)

    Song, Quanfeng

    This report originates from the compulsory defense during my Ph.D. study at the Technical University of Denmark. Resistance welding is an old and well-proven technology. Yet the emergence of more and more new materials, new designs, invention off new joining techniques, and more stringent...... requirement in quality have imposed challenges to the resistance welding. More some research and development have to be done to adapt the old technology to the manufacturing industry of the 21st century. In the 1st part of the report, the challenging factors to the resistance welding are reviewed. Numerical...... simulation of resistance welding has been under development for many years. Yet it is no easy to make simulation results reliable and accurate because of the complexity of resistance welding process. In the 2nd part of the report numerical modeling of resistance welding is reviewed, some critical factors...

  9. Multidrug-Resistant Candida

    DEFF Research Database (Denmark)

    Arendrup, Maiken Cavling; Patterson, Thomas F

    2017-01-01

    Invasive Candida infections remain an important cause of morbidity and mortality, especially in hospitalized and immunocompromised or critically ill patients. A limited number of antifungal agents from only a few drug classes are available to treat patients with these serious infections. Resistance...... can be either intrinsic or acquired. Resistance mechanisms are not exchanged between Candida; thus, acquired resistance either emerges in response to an antifungal selection pressure in the individual patient or, more rarely, occur due to horizontal transmission of resistant strains between patients....... Although multidrug resistance is uncommon, increasing reports of multidrug resistance to the azoles, echinocandins, and polyenes have occurred in several Candida species, most notably Candida glabrata and more recently Candida auris. Drivers are overall antifungal use, subtherapeutic drug levels at sites...

  10. Resistance in Everyday Life

    DEFF Research Database (Denmark)

    This book is about resistance in everyday life, illustrated through empirical contexts from different parts of the world. Resistance is a widespread phenomenon in biological, social and psychological domains of human cultural development. Yet, it is not well articulated in the academic literature....... The contributors deal with strategies for handling dissent by individuals or groups, specifically dissent through resistance. Resistance can be a location of intense personal, interpersonal and cultural negotiation, and that is the primary reason for interest in this phenomenon. Ordinary life events contain...

  11. Resistent tuberkulose i Danmark

    DEFF Research Database (Denmark)

    Thomsen, V O; Johansen, I S; Bauer, J O

    2001-01-01

    INTRODUCTION: Increased rates of multidrug-resistant (MDR) tuberculosis (TB) has been reported from countries close to Denmark. We evaluated the incidence of drug resistance in Denmark in order to determine the magnitude of the problem. MATERIALS AND METHODS: Susceptibility testing was performed......-cluster. Among all patients with isoniazid- and streptomycin-resistance, 77.0% had clustered strains. DISCUSSION: In conclusion, although drug resistance among untreated Danes was close to the rate estimated in good national programmes, close monitoring is needed in future years, as active transmission...

  12. Antipastorialism : Resistant Georgic Mode

    National Research Council Canada - National Science Library

    Zimmerman, Donald

    2000-01-01

    .... Abolitionists, women, Afro-British slaves, and those who protested land enclosure developed a multivalent, resistant mode of writing, which I name 'antipastoralism', that countered orthodox, poetical...

  13. Antibiotic resistance in animals.

    Science.gov (United States)

    Barton, Mary D; Pratt, Rachael; Hart, Wendy S

    2003-01-01

    There is currently no systematic surveillance or monitoring of antibiotic resistance in Australian animals. Registration of antibiotics for use in animals is tightly controlled and has been very conservative. Fluoroquinolones have not been registered for use in food producing animals and other products have been removed from the market because of human health concerns. In the late 1970s, the Animal Health Committee coordinated a survey of resistance in Salmonella and Escherichia coli isolates from cattle, pigs and poultry and in bovine Staphylococcus aureus. Some additional information is available from published case reports. In samples collected prior to the withdrawal of avoparcin from the market, no vancomycin resistant Enterococcus faecium or Enterococcus faecalis were detected in samples collected from pigs, whereas some vanA enterococci, including E. faecium and E. faecalis, were found in chickens. No vanB enterococci were detected in either species. Virginiamycin resistance was common in both pig and poultry isolates. Multiple resistance was common in E. coli and salmonellae isolates. No fluoroquinolone resistance was found in salmonellae, E. coli or Campylobacter. Beta-lactamase production is common in isolates from bovine mastitis, but no methicillin resistance has been detected. However, methicillin resistance has been reported in canine isolates of Staphylococcus intermedius and extended spectrum beta-lactamase producing E. coli has been found in dogs.

  14. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Skip to common links HHS U.S. Department of Health and Human Services U.S. Food and Drug Administration A to Z Index Follow FDA En Español Search FDA Submit search ... & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet ...

  15. Resistance and conformity

    NARCIS (Netherlands)

    Sumter, S.R.; Bokhorst, C.L.; Westenberg, P.M.; Levesque, R.J.R.

    2011-01-01

    Resistance to peer influence, or the ability to resist making choices or adopting views under the implicit or explicit influence of your peers, is expected to undergo changes during adolescence. Two developmental trajectories have emerged from the field. On the one hand, adolescents show a temporary

  16. Mechanisms of Antibiotic Resistance

    Science.gov (United States)

    Munita, Jose M.; Arias, Cesar A.

    2015-01-01

    Emergence of resistance among the most important bacterial pathogens is recognized as a major public health threat affecting humans worldwide. Multidrug-resistant organisms have emerged not only in the hospital environment but are now often identified in community settings, suggesting that reservoirs of antibiotic-resistant bacteria are present outside the hospital. The bacterial response to the antibiotic “attack” is the prime example of bacterial adaptation and the pinnacle of evolution. “Survival of the fittest” is a consequence of an immense genetic plasticity of bacterial pathogens that trigger specific responses that result in mutational adaptations, acquisition of genetic material or alteration of gene expression producing resistance to virtually all antibiotics currently available in clinical practice. Therefore, understanding the biochemical and genetic basis of resistance is of paramount importance to design strategies to curtail the emergence and spread of resistance and devise innovative therapeutic approaches against multidrug-resistant organisms. In this chapter, we will describe in detail the major mechanisms of antibiotic resistance encountered in clinical practice providing specific examples in relevant bacterial pathogens. PMID:27227291

  17. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Skip to common links HHS U.S. Department of Health and Human Services U.S. Food and Drug Administration ... Tobacco Products Animal & Veterinary Home Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet ...

  18. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... menu Skip to common links HHS U.S. Department of Health and Human Services U.S. Food and Drug Administration ... Tobacco Products Animal & Veterinary Home Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More ...

  19. Phenotypic Resistance to Antibiotics

    Directory of Open Access Journals (Sweden)

    Jose L. Martinez

    2013-04-01

    Full Text Available The development of antibiotic resistance is usually associated with genetic changes, either to the acquisition of resistance genes, or to mutations in elements relevant for the activity of the antibiotic. However, in some situations resistance can be achieved without any genetic alteration; this is called phenotypic resistance. Non-inherited resistance is associated to specific processes such as growth in biofilms, a stationary growth phase or persistence. These situations might occur during infection but they are not usually considered in classical susceptibility tests at the clinical microbiology laboratories. Recent work has also shown that the susceptibility to antibiotics is highly dependent on the bacterial metabolism and that global metabolic regulators can modulate this phenotype. This modulation includes situations in which bacteria can be more resistant or more susceptible to antibiotics. Understanding these processes will thus help in establishing novel therapeutic approaches based on the actual susceptibility shown by bacteria during infection, which might differ from that determined in the laboratory. In this review, we discuss different examples of phenotypic resistance and the mechanisms that regulate the crosstalk between bacterial metabolism and the susceptibility to antibiotics. Finally, information on strategies currently under development for diminishing the phenotypic resistance to antibiotics of bacterial pathogens is presented.

  20. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... More in Antimicrobial Resistance National Antimicrobial Resistance Monitoring System About NARMS 2015 NARMS Integrated Report Data Meetings ... Deutsch | 日本語 | فارسی | English FDA Accessibility Careers FDA Basics FOIA No FEAR ...

  1. Resistance to change

    NARCIS (Netherlands)

    Dow, J.; Perotti, E.

    2009-01-01

    Established firms often fail to maintain leadership following disruptive market shifts. We argue that such firms are more prone to internal resistance. A radical adjustment of assets affects the distribution of employee rents, creating winners and losers. Losers resist large changes when strong

  2. Resistance to change

    NARCIS (Netherlands)

    Dow, J.; Perotti, E.

    2013-01-01

    Established firms often fail to maintain leadership following disrup tive market shifts. We argue that such firms are more prone to internal resistance. A radical adjustment of assets affects the distribution of employee rents, creating winners and losers. Losers resist large changes when strong

  3. Glycosphingolipids and insulin resistance

    NARCIS (Netherlands)

    Langeveld, Mirjam; Aerts, Johannes M. F. G.

    2009-01-01

    Obesity is associated with an increased risk for insulin resistance, a state characterized by impaired responsiveness of liver, muscle and adipose tissue to insulin. One class of lipids involved in the development of insulin resistance are the (glyco)sphingolipids. Ceramide, the most simple

  4. A study on heat resistance of high temperature resistant coating

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Liping; Wang, Xueying; Zhang, Qibin; Qin, Yanlong; Lin, Zhu [Research Institute of Engineering Technology of CNPC, Tianjin (China)

    2005-04-15

    A high temperature resistant coating has been developed, which is mainly for heavy oil production pipes deserved the serious corrosion. The coating has excellent physical and mechanical performance and corrosion resistance at room and high temperature. In order to simulate the underground working condition of heavy oil pipes,the heat resistance of the high temperature resistant coating has been studied. The development and a study on the heat resistance of the DHT high temperature resistance coating have been introduced in this paper

  5. A study on heat resistance of high temperature resistant coating

    International Nuclear Information System (INIS)

    Zhang, Liping; Wang, Xueying; Zhang, Qibin; Qin, Yanlong; Lin, Zhu

    2005-01-01

    A high temperature resistant coating has been developed, which is mainly for heavy oil production pipes deserved the serious corrosion. The coating has excellent physical and mechanical performance and corrosion resistance at room and high temperature. In order to simulate the underground working condition of heavy oil pipes,the heat resistance of the high temperature resistant coating has been studied. The development and a study on the heat resistance of the DHT high temperature resistance coating have been introduced in this paper

  6. Multidrug-resistant tuberculosis

    Directory of Open Access Journals (Sweden)

    McNerney Ruth

    2008-01-01

    Full Text Available Abstract Background With almost 9 million new cases each year, tuberculosis remains one of the most feared diseases on the planet. Led by the STOP-TB Partnership and WHO, recent efforts to combat the disease have made considerable progress in a number of countries. However, the emergence of mutated strains of Mycobacterium tuberculosis that are resistant to the major anti-tuberculosis drugs poses a deadly threat to control efforts. Multidrug-resistant tuberculosis (MDR-TB has been reported in all regions of the world. More recently, extensively drug resistant-tuberculosis (XDR-TB that is also resistant to second line drugs has emerged in a number of countries. To ensure that adequate resources are allocated to prevent the emergence and spread of drug resistance it is important to understand the scale of the problem. In this article we propose that current methods of describing the epidemiology of drug resistant tuberculosis are not adequate for this purpose and argue for the inclusion of population based statistics in global surveillance data. Discussion Whereas the prevalence of tuberculosis is presented as the proportion of individuals within a defined population having disease, the prevalence of drug resistant tuberculosis is usually presented as the proportion of tuberculosis cases exhibiting resistance to anti-tuberculosis drugs. Global surveillance activities have identified countries in Eastern Europe, the former Soviet Union and regions of China as having a high proportion of MDR-TB cases and international commentary has focused primarily on the urgent need to improve control in these settings. Other regions, such as sub-Saharan Africa have been observed as having a low proportion of drug resistant cases. However, if one considers the incidence of new tuberculosis cases with drug resistant disease in terms of the population then countries of sub-Saharan Africa have amongst the highest rates of transmitted MDR-TB in the world. We propose

  7. Genetics Home Reference: clopidogrel resistance

    Science.gov (United States)

    ... Facebook Twitter Home Health Conditions Clopidogrel resistance Clopidogrel resistance Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Clopidogrel resistance is a condition in which the drug clopidogrel ...

  8. Genetics Home Reference: warfarin resistance

    Science.gov (United States)

    ... Email Facebook Twitter Home Health Conditions Warfarin resistance Warfarin resistance Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Warfarin resistance is a condition in which individuals have ...

  9. Hydraulic resistance of biofilms

    KAUST Repository

    Dreszer, C.

    2013-02-01

    Biofilms may interfere with membrane performance in at least three ways: (i) increase of the transmembrane pressure drop, (ii) increase of feed channel (feed-concentrate) pressure drop, and (iii) increase of transmembrane passage. Given the relevance of biofouling, it is surprising how few data exist about the hydraulic resistance of biofilms that may affect the transmembrane pressure drop and membrane passage. In this study, biofilms were generated in a lab scale cross flow microfiltration system at two fluxes (20 and 100Lm-2h-1) and constant cross flow (0.1ms-1). As a nutrient source, acetate was added (1.0mgL-1 acetate C) besides a control without nutrient supply. A microfiltration (MF) membrane was chosen because the MF membrane resistance is very low compared to the expected biofilm resistance and, thus, biofilm resistance can be determined accurately. Transmembrane pressure drop was monitored. As biofilm parameters, thickness, total cell number, TOC, and extracellular polymeric substances (EPS) were determined, it was demonstrated that no internal membrane fouling occurred and that the fouling layer actually consisted of a grown biofilm and was not a filter cake of accumulated bacterial cells. At 20Lm-2h-1 flux with a nutrient dosage of 1mgL-1 acetate C, the resistance after 4 days reached a value of 6×1012m-1. At 100Lm-2h-1 flux under the same conditions, the resistance was 5×1013m-1. No correlation of biofilm resistance to biofilm thickness was found; Biofilms with similar thickness could have different resistance depending on the applied flux. The cell number in biofilms was between 4×107 and 5×108 cellscm-2. At this number, bacterial cells make up less than a half percent of the overall biofilm volume and therefore did not hamper the water flow through the biofilm significantly. A flux of 100Lm-2h-1 with nutrient supply caused higher cell numbers, more biomass, and higher biofilm resistance than a flux of 20Lm-2h-1. However, the biofilm thickness

  10. Antibiotic Resistance in Foodborne Pathogens

    OpenAIRE

    Walsh, Ciara; Duffy, Geraldine

    2013-01-01

    Wide-spread antibiotic resistance among bacterial pathogens is now a serious public health issue and multi-antibiotic resistance has been reported in many foodborne pathogens including Salmonella and E. coli. A study to determine antibiotic resistance profiles of a range of Salmonella and Verocytotoxigenic E.coli (VTEC) isolated from Irish foods revealed significant levels of antibiotic resistance in the strains. S. typhimurium DT104 were multiantibiotic resistant with 97% resistant to 7 anti...

  11. FRC collisionless resistivity

    International Nuclear Information System (INIS)

    Tajima, T.; Horton, W.

    1990-01-01

    Ions in the field reversed configuration (FRC) exhibit stochastic orbits due to the field null and the curvature of poloidal field lines. Velocity correlations of these particles decay in a power law fashion t -m where 1 ≤ m ≤ 2. This decay of the single particle correlation function is characteristic of the long tail correlations of strongly chaotic or nonlinear systems found in other problems of statistical physics. This decay of correlations gives rise to a collisionless resistivity that can far exceed the collisional resistivity in an FRC plasma. The finite correlation τ c of a single particle limits the acceleration in the electric field producing the finite resistivity. Maxwellian test particle distributions are integrated to find the measure of the set of stochastic ions that contribute to the collisionless resistivity. The computed conductivity is proportional to the square root of the characteristic ion gyroradius in both simulation and theory

  12. Antimicrobial (Drug) Resistance Prevention

    Science.gov (United States)

    ... June 6, 2018 HIV Vaccine Elicits Antibodies in Animals that Neutralize Dozens of HIV Strains , June 4, 2018 ... Antimicrobial (Drug) Resistance > Understanding share with facebook share with twitter share ...

  13. Antibiotics and Resistance: Glossary

    Science.gov (United States)

    ... chromosomes and plasmids. Transposons often carry genes specifying antimicrobial resistance. Virus An extremely small infective agent, visible only with an electron microscope. Viruses can cause disease in humans, animals and plants. Viruses consist of a protein coat ...

  14. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... search Popular ... produced a nine-minute animation explaining how antimicrobial resistance both emerges and proliferates among bacteria. Over time, the use of antimicrobial drugs will ...

  15. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... bacteria. Over time, the use of antimicrobial drugs will result in the development of resistant strains of ... and other key audiences. We hope this animation will make the concept more understandable to non-scientists ...

  16. Treatment-Resistant Schizophrenia

    DEFF Research Database (Denmark)

    Howes, Oliver D; McCutcheon, Rob; Agid, Ofer

    2017-01-01

    OBJECTIVE: Research and clinical translation in schizophrenia is limited by inconsistent definitions of treatment resistance and response. To address this issue, the authors evaluated current approaches and then developed consensus criteria and guidelines. METHOD: A systematic review of randomize...

  17. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... it More sharing options Linkedin Pin it Email Print The Food and Drug Administration's (FDA's) Center for ... issue of antimicrobial resistance is that the subject material appears abstract and is complex. This video was ...

  18. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... produced material may be copied, reproduced, and distributed as long as FDA's Center for Veterinary Medicine is cited as the corporate author. Animation Animation of Antimicrobial Resistance ( ...

  19. Piggyback resistive Micromegas

    CERN Document Server

    Attié, D; Durand, D; Desforge, D; Ferrer-Ribas, E; Galán, J; Giomataris, Y; Gongadze, A; Iguaz, F J; Jeanneau, F; de Oliveira, R; Papaevangelou, T; Peyaud, A; Teixeira, A

    2013-01-01

    Piggyback Micromegas consists in a novel readout architecture where the anode element is made of a resistive layer on a ceramic substrate. The resistive layer is deposited on the thin ceramic substrate by an industrial process which provides large dynamic range of resistivity (10$^6$ to 10$^{10}$\\,M$\\Omega$/square). The particularity of this new structure is that the active part is entirely dissociated from the read-out element. This gives a large flexibility on the design of the anode structure and the readout scheme. Without significant loss, signals are transmitted by capacitive coupling to the read-out pads. The detector provides high gas gain, good energy resolution and the resistive layer assures spark protection for the electronics. This assembly could be combined with modern pixel array electronic ASICs. First tests with different Piggyback detectors and configurations will be presented. This structure is adequate for cost effective fabrication and low outgassing detectors. It was designed to perform ...

  20. Antibiotic-Resistant Gonorrhea

    Science.gov (United States)

    ... Search Form Controls Cancel Submit Search the CDC Gonorrhea Note: Javascript is disabled or is not supported ... on Facebook Sexually Transmitted Diseases (STDs) Antibiotic-Resistant Gonorrhea Recommend on Facebook Tweet Share Compartir Low Resolution ...

  1. Cotrimoxazole Resistant Chancroid

    Directory of Open Access Journals (Sweden)

    Kamlender Singh

    1985-01-01

    Full Text Available Four male young adults, after contact with prostitutes, developed clinically typical chancroid which was resistant to cotrimoxazole alone and also in combination with tetracycline. With chloramphenicol, the response was quick and complete with no untoward side effects.

  2. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Resistance Monitoring System About NARMS 2015 NARMS Integrated Report Data Meetings and Publications Resources Judicious Use of ... back to top Popular Content Home Latest Recalls Report an Adverse Event MedWatch Safety Alerts News Releases ...

  3. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... complex. This video was designed to make the concept of antimicrobial resistance more real and understandable to ... audiences. We hope this animation will make the concept more understandable to non-scientists by showing how ...

  4. MULTIDRUG-RESISTANT TUBERCULOSIS

    African Journals Online (AJOL)

    Kurt

    health, with the focus of DOTS programmes on cure of infectious TB patients and prevention of drug resistance. ... Despite highly effective drugs and disease control strategies, morbidity and mortality .... notification and registration system.

  5. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... One of the major obstacles to understanding the issue of antimicrobial resistance is that the subject material ... Website Policies U.S. Food and Drug Administration 10903 New Hampshire Avenue Silver Spring, MD 20993 1-888- ...

  6. Adiabatic and isothermal resistivities

    International Nuclear Information System (INIS)

    Fishman, R.S.

    1989-01-01

    The force-balance method is used to calculate the isothermal resistivity to first order in the electric field. To lowest order in the impurity potential, the isothermal resistivity disagrees with the adiabatic results of the Kubo formula and the Boltzmann equation. However, an expansion of the isothermal resistivity in powers of the impurity potential is divergent, with two sets of divergent terms. The first set arises from the density matrix of the relative electron-phonon system. The second set arises from the explicit dependence of the density matrix on the electric field, which was ignored by force-balance calculations. These divergent contributions are calculated inductively, by applying a recursion relation for the Green's functions. Using the λ 2 t→∞ limit of van Hove, I show that the resummation of these divergent terms yields the same result for the resistivity as the adiabatic calculations, in direct analogy with the work of Argyres and Sigel, and Huberman and Chester

  7. Antibiotics and Antibiotic Resistance

    Science.gov (United States)

    ... all that ails you. Antibiotics, also known as antimicrobial drugs, are drugs that fight infections caused by bacteria. ... Information for Consumers and Health Professionals Information by drug class Antimicrobial Resistance Animal and Veterinary Related Resources Further information ...

  8. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... proliferates among bacteria. Over time, the use of antimicrobial drugs will result in the development of resistant strains ... bacteria, complicating clinician's efforts to select the appropriate ... and human medicine to preserve the effectiveness of these drugs. One ...

  9. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... use of antimicrobial drugs will result in the development of resistant strains of bacteria, complicating clinician's efforts ... Inspections & Compliance Federal, State & Local Officials Consumers Health Professionals Science & Research Industry Scroll back to top Popular ...

  10. Regicide and Resistance

    DEFF Research Database (Denmark)

    Flohr, Mikkel

    2016-01-01

    This article examines the role of resistance in Michel Foucault’s political thought. The article recovers this otherwise obscured aspect of Foucault’s thought through a systematic analysis of his theoretical regicide and consequent reconceptualization of power, agency and resistance. It is argued...... that Foucault developed a highly original account of resistance, which was, and should continue to be considered, central to his thought and its critical potential. It is shown how Foucault’s concept of resistance overcomes the limitation of voluntarism and determinism, which continue to mare contemporary...... political theory, providing a passage from the critique of contemporary configurations of power to the irrepressible possibility that they may be contested and changed....

  11. Stab resistant body armour

    OpenAIRE

    Horsfall, I

    2000-01-01

    There is now a widely accepted need for stab resistant body armour for the police in the UK. However, very little research has been done on knife resistant systems and the penetration mechanics of sharp projectiles are poorly understood. This thesis explores the general background to knife attack and defence with a particular emphasis on the penetration mechanics of edged weapons. The energy and velocity that can be achieved in stabbing actions has been determined for a numb...

  12. Radiation resistant modified polypropylene

    International Nuclear Information System (INIS)

    Bojarski, J.; Zimek, Z.

    1997-01-01

    Radiation technology for production of radiation resistant polypropylene for medical use has been presented. The method consists in radiation induced copolymerization of polypropylene with ethylene and addition of small amount of copolymer of polyethylene and vinyl acetate. The material of proposed composition has a very good mechanical properties and elevated radiation resistivity decided on possibility of radiosterilization of products made of this material and designed for medical use. 3 figs, 3 tabs

  13. Analysis of Online DBA Algorithm with Adaptive Sleep Cycle in WDM EPON

    Science.gov (United States)

    Pajčin, Bojan; Matavulj, Petar; Radivojević, Mirjana

    2018-05-01

    In order to manage Quality of Service (QoS) and energy efficiency in the optical access network, an online Dynamic Bandwidth Allocation (DBA) algorithm with adaptive sleep cycle is presented. This DBA algorithm has the ability to allocate an additional bandwidth to the end user within a single sleep cycle whose duration changes depending on the current buffers occupancy. The purpose of this DBA algorithm is to tune the duration of the sleep cycle depending on the network load in order to provide service to the end user without violating strict QoS requests in all network operating conditions.

  14. Performance of the IEEE 802.3 EPON registration scheme under high load

    Science.gov (United States)

    Bhatia, Swapnil P.; Bartos, Radim

    2004-09-01

    The proposed standard for the IEEE 802.3 Ethernet Passive Optical Network includes a random delayed transmission scheme for registration of new nodes. Although the scheme performs well on low loads, our simulation demonstrates the degraded and undesirable performance of the scheme at higher loads. We propose a simple modification to the current scheme that increases its range of operation and is compatible with the IEEE draft standard. We demonstrate the improvement in performance gained without any significant increase in registration delay.

  15. An enhanced DWBA algorithm in hybrid WDM/TDM EPON networks with heterogeneous propagation delays

    Science.gov (United States)

    Li, Chengjun; Guo, Wei; Jin, Yaohui; Sun, Weiqiang; Hu, Weisheng

    2011-12-01

    An enhanced dynamic wavelength and bandwidth allocation (DWBA) algorithm in hybrid WDM/TDM PON is proposed and experimentally demonstrated. In addition to the fairness of bandwidth allocation, this algorithm also considers the varying propagation delays between ONUs and OLT. The simulation based on MATLAB indicates that the improved algorithm has a better performance compared with some other algorithms.

  16. Electron Beam Induced Mass Loss Dependence on Stained Thin Epon Resin Sections

    Czech Academy of Sciences Publication Activity Database

    Skoupý, Radim; Nebesářová, Jana; Krzyžánek, Vladislav

    2016-01-01

    Roč. 22, S3 (2016), s. 926-927 ISSN 1431-9276 R&D Projects: GA ČR(CZ) GA14-20012S; GA MŠk(CZ) LO1212; GA MŠk ED0017/01/01 Institutional support: RVO:68081731 ; RVO:60077344 Keywords : TEM * STEM * EFTEM Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering; JA - Electronics ; Optoelectronics, Electrical Engineering (BC-A) Impact factor: 1.891, year: 2016

  17. Clopidogrel Resistance: Current Issues

    Directory of Open Access Journals (Sweden)

    NS Neki

    2016-05-01

    Full Text Available Antiplatelet agents are mainly used in the prevention and management of atherothrombotic complications. Dual antiplatelet therapy, combining aspirin and clopidogrel, is the standard care for patients having acute coronary syndromes or undergoing percutaneous coronary intervention according to the current ACC/AHA and ESC guidelines. But in spite of administration of dual antiplatelet therapy, some patients develop recurrent cardiovascular ischemic events especially stent thrombosis which is a serious clinical problem. Antiplatelet response to clopidogrel varies widely among patients based on ex vivo platelet function measurements. Clopidogrel is an effective inhibitor of platelet activation and aggregation due to its selective and irreversible blockade of the P2Y12 receptor. Patients who display little attenuation of platelet reactivity with clopidogrel therapy are labeled as low or nonresponders or clopidogrel resistant. The mechanism of clopidogrel resistance remains incompletely defined but there are certain clinical, cellular and genetic factors including polymorphisms responsible for therapeutic failure. Currently there is no standardized or widely accepted definition of clopidogrel resistance. The future may soon be realised in the routine measurement of platelet activity in the same way that blood pressure, cholesterol and blood sugar are followed to help guide the therapy, thus improving the care for millions of people. This review focuses on the methods used to identify patients with clopidogrel resistance, the underlying mechanisms, metabolism, clinical significance and current therapeutic strategies to overcome clopidogrel resistance. J Enam Med Col 2016; 6(1: 38-46

  18. CONTACT RESISTANCE MODELING

    Directory of Open Access Journals (Sweden)

    S. V. LOSKUTOV

    2018-05-01

    Full Text Available Purpose. To determine the contribution of the real contact spots distribution in the total conductivity of the conductors contact. Methodology. The electrical contact resistance research was carried out on models. The experimental part of this work was done on paper with a graphite layer with membranes (the first type and conductive liquids with discrete partitions (the second type. Findings. It is shown that the contact electrical resistance is mainly determined by the real area of metal contact. The experimental dependence of the electrical resistance of the second type model on the distance between the electrodes and the potential distribution along the sample surface for the first type model were obtained. The theoretical model based on the principle of electric field superposition was considered. The dependences obtained experimentally and calculated by using the theoretical model are in good agreement. Originality. The regularity of the electrical contact resistance formation on a large number of membranes was researched for the first time. A new model of discrete electrical contact based on the liquid as the conducting environment with nuclear membrane partitions was developed. The conclusions of the additivity of contact and bulk electrical resistance were done. Practical value. Based on these researches, a new experimental method of kinetic macroidentation that as a parameter of the metal surface layer deformation uses the real contact area was developed. This method allows to determine the value of average contact stresses, yield point, change of the stress on the depth of deformation depending on the surface treatment.

  19. Resistance to technological progress

    International Nuclear Information System (INIS)

    Isensee, J.

    1983-01-01

    This article deals with the tolerance test the constitutional system (Basic Law) of the Federal Republic of Germany is currently put to as a consequence of the resistance to the power structure of this country, which is expressed in the name of protection and defense for the environment and world peace. This biopacifistic resistance movment, the author says, has nothing to do with the legal right to resist, as laid down in art. 20 (4) of the Basic Law. According to the author, this attitude is an offspring of fear of the hazards of technological progress, primarily of nuclear hazards. Practical resistance, the author states, is preceded by theoretical resistance in speech: De-legitimation of the democratic legality, of the parliamentary functions, of the supreme power of the government, and denial of the citizens duty of obedience. The author raises the question as to whether this attitude of disobedience on ecological grounds marks the onset of a fourth stage of development of the modern state, after we have passed through stages characterised by fear of civil war, of tyranny, and of social privation and suffering. There are no new ideas brought forward by the ecologically minded movement, the author says, for re-shaping our institutions or constitutional system. (HP) [de

  20. Biological improvement of radiation resistance

    Energy Technology Data Exchange (ETDEWEB)

    Chun, K J; Lee, Y K; Kim, J S; Kim, J K; Lee, S J

    2000-08-01

    To investigate the mechanisms of gene action related to the radiation resistance in microorganisms could be essentially helpful for the development of radiation protectants and hormeric effects of low dose radiation. This book described isolation of radiation-resistant microorganisms, induction of radiation-resistant and functionally improved mutants by gamma-ray radiation, cloning and analysis of the radiation resistance related genes and analysis of the expressed proteins of the radiation resistant related genes.

  1. Biological improvement of radiation resistance

    International Nuclear Information System (INIS)

    Chun, K. J.; Lee, Y. K.; Kim, J. S.; Kim, J. K.; Lee, S. J.

    2000-08-01

    To investigate the mechanisms of gene action related to the radiation resistance in microorganisms could be essentially helpful for the development of radiation protectants and hormeric effects of low dose radiation. This book described isolation of radiation-resistant microorganisms, induction of radiation-resistant and functionally improved mutants by gamma-ray radiation, cloning and analysis of the radiation resistance related genes and analysis of the expressed proteins of the radiation resistant related genes

  2. Heat-resistant materials

    CERN Document Server

    1997-01-01

    This handbook covers the complete spectrum of technology dealing with heat-resistant materials, including high-temperature characteristics, effects of processing and microstructure on high-temperature properties, materials selection guidelines for industrial applications, and life-assessment methods. Also included is information on comparative properties that allows the ranking of alloy performance, effects of processing and microstructure on high-temperature properties, high-temperature oxidation and corrosion-resistant coatings for superalloys, and design guidelines for applications involving creep and/or oxidation. Contents: General introduction (high-temperature materials characteristics, and mechanical and corrosion properties, and industrial applications); Properties of Ferrous Heat-Resistant Alloys (carbon, alloy, and stainless steels; alloy cast irons; and high alloy cast steels); Properties of superalloys (metallurgy and processing, mechanical and corrosion properties, degradation, and protective coa...

  3. Fast Resistive Bolometer

    International Nuclear Information System (INIS)

    Deeney, C.; Fehl, D.L.; Hanson, D.L.; Keltner, N.R.; McGurn, J.S.; McKenney, J.L.; Spielman, R.B.

    1999-01-01

    Resistive bolometry is an accurate, robust, spectrally broadband technique for measuring absolute x-ray fluence and flux. Bolometry is an independent technique for x-ray measurements that is based on a different set of physical properties than other diagnostics such as x-ray diodes, photoconducting detectors, and P-I-N diodes. Bolometers use the temperature-driven change in element resistivity to determine the total deposited energy. The calibration of such a device is based on fundamental material properties and its physical dimensions. We describe the use of nickel and gold bolometers to measure x rays generated by high-power z pinches on Sandia's Saturn and Z accelerators. The Sandia bolometer design described herein has a pulse response of ∼1 ns. We describe in detail the fabrication, fielding, and data analysis issues leading to highly accurate x-ray measurements. The fundamental accuracy of resistive bolometry will be discussed

  4. Kinetically Controlled Drug Resistance

    DEFF Research Database (Denmark)

    Sun, Xin E.; Hansen, Bjarne Gram; Hedstrom, Lizbeth

    2011-01-01

    The filamentous fungus Penicillium brevicompactum produces the immunosuppressive drug mycophenolic acid (MPA), which is a potent inhibitor of eukaryotic IMP dehydrogenases (IMPDHs). IMPDH catalyzes the conversion of IMP to XMP via a covalent enzyme intermediate, E-XMP*; MPA inhibits by trapping E...... of resistance is not apparent. Here, we show that, unlike MPA-sensitive IMPDHs, formation of E-XMP* is rate-limiting for both PbIMPDH-A and PbIMPDH-B. Therefore, MPA resistance derives from the failure to accumulate the drug-sensitive intermediate....

  5. [Resistance risk, cross-resistance and biochemical resistance mechanism of Laodelphax striatellus to buprofezin].

    Science.gov (United States)

    Mao, Xu-lian; Liu, Jin; Li, Xu-ke; Chi, Jia-jia; Liu, Yong-jie

    2016-01-01

    In order to investigate the resistance development law and biochemical resistance mechanism of Laodelphax striatellus to buprofezin, spraying rice seedlings was used to continuously screen resistant strains of L. striatellus and dipping rice seedlings was applied to determine the toxicity and cross-resistance of L. striatellus to insecticides. After 32-generation screening with buprofezin, L. striatellus developed 168.49 folds resistance and its reality heritability (h2) was 0.11. If the killing rate was 80%-90%, L. striatellus was expected to develop 10-fold resistance to buprofezin only after 5 to 6 generations breeding. Because the actual reality heritability of field populations was usually lower than that of the resistant strains, the production of field populations increasing with 10-fold resistance would need much longer time. The results of cross-resistance showed that resistant strain had high level cross-resistance with thiamethoxam and imidacloprid, low level cross-resistance with acetamiprid, and no cross-resistance with pymetrozine and chlorpyrifos. The activity of detoxification enzymes of different strains and the syergism of synergist were measured. The results showed that cytochrome P450 monooxygenase played a major role in the resistance of L. striatellus to buprofezin, the esterase played a minor role and the GSH-S-transferase had no effect. Therefore, L. striatellus would have high risk to develop resistance to buprofezin when used in the field and might be delayed by using pymetrozine and chlorpyrifos.

  6. Resistive effects in EXTRAP

    International Nuclear Information System (INIS)

    Tendler, M.

    1987-01-01

    Theoretical studies of the resistive equilibrium and stability of an EXTRAP Z-pinch are reported. Extending the previous analysis we reasses properties of the resistive equilibrium in EXTRAP with the emphasis on the time dependence of the latter. We also qualitatively consider the role of resistive instabilities in EXTRAP, showing that the typical timescale of the filamentation of the discharge (i.e., the non-linear development of the tearing instability) is comparable, at present, to the discharge duration. On the other hand, we emphasize that this phenomenon may still be consistent with the experimental observation of the Bennet's equilibrium. The processes of the current start-up and ramp-up are also analysed for EXTRAP and it is shown that the peculiarities of these processes may lead to the compression oscillations around an evolving rather stable equilibrium. Finally, some consequences of the average minimum-B concept for EXTRAP are discussed and it is shown that this issue virtually reduces to the appearance of the negative curvature of the magnetic field at the periphery. The maximum attainable value of β at the periphery of the pinch is obtained, as required by the ballooning stability criterion. The influence of the finite resistivity on the ballooning mode is also estimated. (orig.)

  7. Shatter resistance in sesame

    International Nuclear Information System (INIS)

    Langham, D.R.

    2001-01-01

    The majority of the world's sesame (probably over 99%) is shattering, and most of the harvest is manual. In a non-mechanized environment the last thing that farmers want is seed retention (''hold''). They want the seed to fall out as easily as possible. The amount of shattering desired is dependent on the method of harvest. By 1944 the first stage of mechanization was initiated. The indehiscent mutant found in 1943 showed in succeeding generations that it was controlled monogenically, and the homozygous recessive (id/id) gave indehiscence. Unfortunately, the id allele had pleiotropic effects including cupped leaves, twisted stems, short seed pods, semi-sterility, and low yield. Improvements in shatter resistance are relative within a specific program. For example, Sesaco has improved its shatter resistance each year, and still for the USA methods of harvest, further improvements are necessary to allow for better retention in adverse weather. This paper presents a methodology for quantifying shatter resistance so researchers can compare levels of shatter resistance between programs. (author)

  8. Corrosion resistant steel

    International Nuclear Information System (INIS)

    Zubchenko, A.S.; Borisov, V.P.; Latyshev, V.B.

    1980-01-01

    Corrosion resistant steel for production of sheets and tubes containing C, Mn, Cr, Si, Fe is suggested. It is alloyed with vanadium and cerium for improving tensile properties and ductility. The steel can be melted by a conventional method in electric-arc or induction furnaces. The mentioned steel is intended to be used as a substitute for nickel-bearing austenitic steels

  9. Viscous, Resistive Magnetorotational Modes

    DEFF Research Database (Denmark)

    Pessah, Martin Elias; Chan, Chi-kwan

    2008-01-01

    We carry out a comprehensive analysis of the behavior of the magnetorotational instability (MRI) in viscous, resistive plasmas. We find exact, non-linear solutions of the non-ideal magnetohydrodynamic (MHD) equations describing the local dynamics of an incompressible, differentially rotating...

  10. The resistance brand

    DEFF Research Database (Denmark)

    Gulbrandsen, Ib Tunby; Just, Sine Nørholm; Uldam, Julie

    “The Trump-resistance will be commercialized” (Hess, 2017). Paraphrasing political activist and artist Gil Scott-Heron’s famous title seems increasingly apt as one corporation after the other voices sympathy with social protesters and/or dismay at the politics of the White House incumbent. But how...

  11. Corrosion resistant composite materials

    International Nuclear Information System (INIS)

    Ul'yanin, E.A.

    1986-01-01

    Foundations for corrosion-resistant composite materials design are considered with account of components compatibility. Fibrous and lamellar composites with metal matrix, dispersion-hardened steels and alloys, refractory metal carbides-, borides-, nitrides-, silicides-based composites are described. Cermet compositions and fields of their application, such as protective coatings for operation in agressive media at high temperatures, are presented

  12. Resistive effects in EXTRAP

    International Nuclear Information System (INIS)

    Tendler, M.

    1985-10-01

    Theoretical studies of the resistive equilibrium and stability of an EXTRAP z-pinch are reported. Extending the previous analysis we reassess properties of the resistive equilibrium in EXTRAP with the emphasis on the time dependence of the latter. We also qualitatively consider the role of resistive instabilities in EXTRAP, showing that the typical timescale of the filamentation of the discharge (i.e. the non-linear development of the tearing instability) is comparable at present, to the discharge duration. On the other hand, we emphasize that this phenomenon may still be consistent with the experimental observation of the Bennet's equilibrium. The processes of the current start-up and ramp up are also analysed for EXTRAP and it is shown that the peculiarities if these processes in EXTRAP may lead to the compression oscillations around and evolving rather stable equilibrium. The frequency of these oscillations is given. Finally, some consequences of the average minimum-B concept for EXTRAP are discussed and it is shown that this issue virtually reduces to the appearance of the negative curvature of the magnetic field at the periphery. The maximum attainable value of β at the periphery of the pinch is obtained, as required by the ballooning stability criterion. The influence of the finite resistivity on the ballooning mode is also estimated. With 4 figures and 21 refs. (Author)

  13. Oseltamivir-Resistant Flu

    Centers for Disease Control (CDC) Podcasts

    2012-04-13

    Dr. Aaron Storms, an Epidemic Intelligence Service (EIS) officer at CDC, discusses his paper about oseltamivir-resistant H1N1flu.  Created: 4/13/2012 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 4/17/2012.

  14. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Pin it Email Print The Food and Drug Administration's (FDA's) Center for Veterinary Medicine (CVM) produced a nine-minute animation explaining how antimicrobial resistance both emerges and proliferates among bacteria. Over time, the use of antimicrobial drugs will result in ...

  15. Multidrug-Resistant Tuberculosis

    Centers for Disease Control (CDC) Podcasts

    In this podcast, Dr. Oeltmann discusses multidrug-resistant tuberculosis. An outbreak occurred in Thailand, which led to 45 cases in the U.S. This serious illness can take up to 2 years to treat. MDR TB is a real threat and a serious condition.

  16. Animation of Antimicrobial Resistance

    Medline Plus

    Full Text Available ... Español Search FDA Submit search Popular Content Home Food Drugs Medical Devices Radiation-Emitting Products Vaccines, ... Biologics Animal & Veterinary Cosmetics Tobacco Products Animal & Veterinary Home Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of ...

  17. Overcoming Resistance to Change

    Science.gov (United States)

    Hull, Ted H.; Balka, Don S.; Miles, Ruth Harbin

    2010-01-01

    Resistance to change is a major obstacle in developing and implementing effective instructional programs, yet it is rarely considered, discussed, or addressed. The school leaders who are responsible for improvement frequently feel that their efforts are being blocked or thwarted. For the most part, they are correct, but they may not realize that…

  18. Antibiotic Resistance and Fungus

    Centers for Disease Control (CDC) Podcasts

    2017-02-28

    Dr. David Denning, President of the Global Action Fund for Fungal Infections and an infectious diseases clinician, discusses antimicrobial resistance and fungus.  Created: 2/28/2017 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 2/28/2017.

  19. Measurement of Dynamic Resistance in Resistance Spot Welding

    DEFF Research Database (Denmark)

    Wu, Pei; Zhang, Wenqi; Bay, Niels

    Through years, the dynamic resistance across the electrodes has been used for weld quality estimation and contact resistance measurement. However, the previous methods of determining the dynamic resistance were mostly based on measuring the voltage and current on the secondary side of the transfo......Through years, the dynamic resistance across the electrodes has been used for weld quality estimation and contact resistance measurement. However, the previous methods of determining the dynamic resistance were mostly based on measuring the voltage and current on the secondary side...... of the transformer in resistance welding machines, implying defects from induction noise and interference with the leads connected to the electrodes for measuring the voltage. In this study, the dynamic resistance is determined by measuring the voltage on the primary side and the current on the secondary side...

  20. HIV resistance testing and detected drug resistance in Europe

    DEFF Research Database (Denmark)

    Schultze, Anna; Phillips, Andrew N; Paredes, Roger

    2015-01-01

    to Southern Europe. CONCLUSIONS: Despite a concurrent decline in virological failure and testing, drug resistance was commonly detected. This suggests a selective approach to resistance testing. The regional differences identified indicate that policy aiming to minimize the emergence of resistance......OBJECTIVES: To describe regional differences and trends in resistance testing among individuals experiencing virological failure and the prevalence of detected resistance among those individuals who had a genotypic resistance test done following virological failure. DESIGN: Multinational cohort...... study. METHODS: Individuals in EuroSIDA with virological failure (>1 RNA measurement >500 on ART after >6 months on ART) after 1997 were included. Adjusted odds ratios (aORs) for resistance testing following virological failure and aORs for the detection of resistance among those who had a test were...

  1. Resistance of Bacteria to Biocides.

    Science.gov (United States)

    Maillard, Jean-Yves

    2018-04-01

    Biocides and formulated biocides are used worldwide for an increasing number of applications despite tightening regulations in Europe and in the United States. One concern is that such intense usage of biocides could lead to increased bacterial resistance to a product and cross-resistance to unrelated antimicrobials including chemotherapeutic antibiotics. Evidence to justify such a concern comes mostly from the use of health care-relevant bacterial isolates, although the number of studies of the resistance characteristics of veterinary isolates to biocides have increased the past few years. One problem remains the definition of "resistance" and how to measure resistance to a biocide. This has yet to be addressed globally, although the measurement of resistance is becoming more pressing, with regulators both in Europe and in the United States demanding that manufacturers provide evidence that their biocidal products will not impact on bacterial resistance. Alongside in vitro evidence of potential antimicrobial cross-resistance following biocide exposure, our understanding of the mechanisms of bacterial resistance and, more recently, our understanding of the effect of biocides to induce a mechanism(s) of resistance in bacteria has improved. This article aims to provide an understanding of the development of antimicrobial resistance in bacteria following a biocide exposure. The sections provide evidence of the occurrence of bacterial resistance and its mechanisms of action and debate how to measure bacterial resistance to biocides. Examples pertinent to the veterinary field are used where appropriate.

  2. Resistant plasmid profile analysis of multidrug resistant Escherichia ...

    African Journals Online (AJOL)

    Multiple drug resistance isolates causing UTI has seri- ous implications for the empiric therapy against patho- genic isolates and for the possible co-selection of antimicrobial resistant mediated by multi drug resistant plasmids21,22. E. coli from clinical isolates are known to harbour plasmids of different molecular sizes23.

  3. Resistant plasmid profile analysis of multidrug resistant Escherichia ...

    African Journals Online (AJOL)

    Background: Multi-drug resistant Escherichia coli has become a major threat and cause of many urinary tract infections (UTIs) in Abeokuta, Nigeria. Objectives: This study was carried out to determine the resistant plasmids of multidrug resistant Escherichia coli isolated from (Urinary tract infections)UTIs in Abeokuta.

  4. Are Sewage Treatment Plants Promoting Antibiotic Resistance?

    Science.gov (United States)

    1. Introduction 1.1. How bacteria exhibit resistance 1.1.1. Resistance to -lactams 1.1.2. Resistance to sulphonamides and trimethoprim 1.1.3. Resistance to macrolides 1.1.4. Resistance to fluoroquinolones 1.1.5. Resistance to tetracyclines 1.1.6. Resistance to nitroimidaz...

  5. Metabolic Resistance in Bed Bugs

    Directory of Open Access Journals (Sweden)

    Omprakash Mittapalli

    2011-03-01

    Full Text Available Blood-feeding insects have evolved resistance to various insecticides (organochlorines, pyrethroids, carbamates, etc. through gene mutations and increased metabolism. Bed bugs (Cimex lectularius are hematophagous ectoparasites that are poised to become one of the major pests in households throughout the United States. Currently, C. lectularius has attained a high global impact status due to its sudden and rampant resurgence. Resistance to pesticides is one factor implicated in this phenomenon. Although much emphasis has been placed on target sensitivity, little to no knowledge is available on the role of key metabolic players (e.g., cytochrome P450s and glutathione S-transferases towards pesticide resistance in C. lectularius. In this review, we discuss different modes of resistance (target sensitivity, penetration resistance, behavioral resistance, and metabolic resistance with more emphasis on metabolic resistance.

  6. Galileo's Trajectory with Mild Resistance

    Science.gov (United States)

    Groetsch, C. W.

    2012-01-01

    An aspect of Galileo's classical trajectory that persists in a simple resistance model is noted. The resistive model provides a case study for the classroom analysis of limiting behaviour of an implicitly defined function. (Contains 1 note.)

  7. Insulin Resistance of Puberty.

    Science.gov (United States)

    Kelsey, Megan M; Zeitler, Philip S

    2016-07-01

    Puberty is a time of considerable metabolic and hormonal change. Notably, puberty is associated with a marked decrease in insulin sensitivity, on par with that seen during pregnancy. In otherwise healthy youth, there is a nadir in insulin sensitivity in mid-puberty, and then it recovers at puberty completion. However, there is evidence that insulin resistance (IR) does not resolve in youth who are obese going into puberty and may result in increased cardiometabolic risk. Little is known about the underlying pathophysiology of IR in puberty, and how it might contribute to increased disease risk (e.g., type 2 diabetes). In this review, we have outlined what is known about the IR in puberty in terms of pattern, potential underlying mechanisms and other mediating factors. We also outline other potentially related metabolic changes that occur during puberty, and effects of underlying insulin resistant states (e.g., obesity) on pubertal changes in insulin sensitivity.

  8. Electrical resistivity probes

    Science.gov (United States)

    Lee, Ki Ha; Becker, Alex; Faybishenko, Boris A.; Solbau, Ray D.

    2003-10-21

    A miniaturized electrical resistivity (ER) probe based on a known current-voltage (I-V) electrode structure, the Wenner array, is designed for local (point) measurement. A pair of voltage measuring electrodes are positioned between a pair of current carrying electrodes. The electrodes are typically about 1 cm long, separated by 1 cm, so the probe is only about 1 inch long. The electrodes are mounted to a rigid tube with electrical wires in the tube and a sand bag may be placed around the electrodes to protect the electrodes. The probes can be positioned in a borehole or on the surface. The electrodes make contact with the surrounding medium. In a dual mode system, individual probes of a plurality of spaced probes can be used to measure local resistance, i.e. point measurements, but the system can select different probes to make interval measurements between probes and between boreholes.

  9. Antifungal resistance in mucorales.

    Science.gov (United States)

    Dannaoui, E

    2017-11-01

    The order Mucorales, which includes the agents of mucormycosis, comprises a large number of species. These fungi are characterised by high-level resistance to most currently available antifungal drugs. Standardised antifungal susceptibility testing methods are now available, allowing a better understanding of the in vitro activity of antifungal drugs against members of Mucorales. Such tests have made apparent that antifungal susceptibility within this group may be species-specific. Experimental animal models of mucormycosis have also been developed and are of great importance in bridging the gap between in vitro results and clinical trials. Amphotericin B, posaconazole and isavuconazole are currently the most active agents against Mucorales; however, their activity remains suboptimal and new therapeutic strategies are needed. Combination therapy could be a promising approach to overcome resistance, but further studies are required to confirm its benefits and safety for patients. Copyright © 2017 Elsevier B.V. and International Society of Chemotherapy. All rights reserved.

  10. Progesterone resistance in endometriosis

    DEFF Research Database (Denmark)

    Patel, Bansari G; Rudnicki, Martin; Yu, Jie

    2017-01-01

    Endometriosis is a common cause of pelvic pain and affects up to 10% of women of reproductive age. Aberrant progesterone signaling in the endometrium plays a significant role in impaired decidualization and establishment of ectopic endometrial implants. Eutopic endometrial cells from women...... with endometriosis fail to downregulate genes needed for decidualization, such as those involved in cell cycle regulation, leading to unbridled proliferation. Several causes of progesterone resistance in the endometrium have been postulated, including congenital "preconditioning", whereby the in utero environment...... renders infants susceptible to neonatal uterine bleeding and endometriosis. Progesterone action is crucial to decreasing inflammation in the endometrium, and deviant progesterone signaling results in a proinflammatory phenotype. Conversely, chronic inflammation can induce a progesterone resistant state...

  11. Antibacterial resistance: an emerging 'zoonosis'?

    Science.gov (United States)

    Labro, Marie-Thérèse; Bryskier, Jean-Marie

    2014-12-01

    Antibacterial resistance is a worldwide threat, and concerns have arisen about the involvement of animal commensal and pathogenic bacteria in the maintenance and spread of resistance genes. However, beyond the facts related to the occurrence of resistant microorganisms in food, food-producing animals and companion animals and their transmission to humans, it is important to consider the vast environmental 'resistome', the selective pathways underlying the emergence of antibacterial resistance and how we can prepare answers for tomorrow.

  12. Corrosion-resistant metal surfaces

    Science.gov (United States)

    Sugama, Toshifumi [Wading River, NY

    2009-03-24

    The present invention relates to metal surfaces having thereon an ultrathin (e.g., less than ten nanometer thickness) corrosion-resistant film, thereby rendering the metal surfaces corrosion-resistant. The corrosion-resistant film includes an at least partially crosslinked amido-functionalized silanol component in combination with rare-earth metal oxide nanoparticles. The invention also relates to methods for producing such corrosion-resistant films.

  13. Shock resistance testing

    International Nuclear Information System (INIS)

    Pouard, M.

    1984-03-01

    In the framework of mechanical tests and to answer the different requests for tests, the T.C.R (Transport Conditionnement et Retraitement) laboratory got test facilities. These installations allow to carry out tests of resistance to shocks, mainly at the safety level of components of nuclear power plants, mockups of transport casks for fuel elements and transport containers for radioactive materials. They include a tower and a catapult. This paper give a decription of the facilities and explain their operation way [fr

  14. Multidrug-Resistant Tuberculosis

    Centers for Disease Control (CDC) Podcasts

    2008-10-28

    In this podcast, Dr. Oeltmann discusses multidrug-resistant tuberculosis. An outbreak occurred in Thailand, which led to 45 cases in the U.S. This serious illness can take up to 2 years to treat. MDR TB is a real threat and a serious condition.  Created: 10/28/2008 by Emerging Infectious Diseases.   Date Released: 10/28/2008.

  15. Resistance and sheet resistance measurements using electron beam induced current

    International Nuclear Information System (INIS)

    Czerwinski, A.; Pluska, M.; Ratajczak, J.; Szerling, A.; KaPtcki, J.

    2006-01-01

    A method for measurement of spatially uniform or nonuniform resistance in layers and strips, based on electron beam induced current (EBIC) technique, is described. High electron beam currents are used so that the overall resistance of the measurement circuit affects the EBIC signal. During the evaluation, the electron beam is scanned along the measured object, whose load resistance varies with the distance. The variation is compensated by an adjustable resistance within an external circuit. The method has been experimentally deployed for sheet resistance determination of buried regions of lateral confinements in semiconductor laser heterostructures manufactured by molecular beam epitaxy

  16. Surveillance of antibiotic resistance

    Science.gov (United States)

    Johnson, Alan P.

    2015-01-01

    Surveillance involves the collection and analysis of data for the detection and monitoring of threats to public health. Surveillance should also inform as to the epidemiology of the threat and its burden in the population. A further key component of surveillance is the timely feedback of data to stakeholders with a view to generating action aimed at reducing or preventing the public health threat being monitored. Surveillance of antibiotic resistance involves the collection of antibiotic susceptibility test results undertaken by microbiology laboratories on bacteria isolated from clinical samples sent for investigation. Correlation of these data with demographic and clinical data for the patient populations from whom the pathogens were isolated gives insight into the underlying epidemiology and facilitates the formulation of rational interventions aimed at reducing the burden of resistance. This article describes a range of surveillance activities that have been undertaken in the UK over a number of years, together with current interventions being implemented. These activities are not only of national importance but form part of the international response to the global threat posed by antibiotic resistance. PMID:25918439

  17. Mechanisms of ouabain resistance

    International Nuclear Information System (INIS)

    Schulz, J.T. III.

    1987-01-01

    Experiments were designed to investigate the mechanism of ouabain resistance in two distinct types of transfected cells derived from ouabain-sensitive CV-1 cell parents. The first type of transfectant is the recipient of a gene encoding the alpha subunit of the rodent renal Na,K-ATPase (R-alphal gene); the second type of transfectant is the recipient of the mouse ouabain resistance gene. Measurements of 86 Rb + uptake and Na,K=ATPase activity in R-alphal gene transfectant cells and CV-1 parent cells indicate that the ouabain-resistant phenotype of the transfectants is due to expression of a relatively ouabain-insensitive Na,K=ATPase. CV-1 parent cells express one component of ouabain sensitive 86 Rb + uptake and one component of ouabain-sensitive Na, K-ATPase activity. R-alpha 1 gene transfectants express the parental forms of ouabain-sensitive 86 Rb + uptake and Na,K-ATPase activity, but in addition express new,relatively ouabain-insensitive forms of 86 Rb + uptake activity and Na,K-ATPase activity

  18. Radiation resistant lining material

    International Nuclear Information System (INIS)

    Ouchi, Koki; Okagawa, Seigo; Tamaki, Hidehiro.

    1990-01-01

    Rigidity, viscoelasticity, flexibility, radiation resistance, leaching resistance, rust-proofness, endurance, etc. are required for the lining materials to wall surfaces and floor surfaces of facilities used under the effect of radiation rays and for the inner surface protection of vessels for radioactive wastes. The present invention provides radiation resistant lining material capable of satisfying such various requirements in a well-balanced manner. That is, the material contains (A) 100 parts by weight of rapidly curing cement, (B) 50 to 300 % by weight of aggregate, and (C) 80 to 120 parts by weight of polymer emulsion. As the specific example, the ingredient (A) is commercially available under the trade name of Jet Cement. The aggregate of the ingredient (B) has preferably from about 0.6 to 0.2 mm of size and is made of material, preferably, silicon or iron grains. As the ingredient (C), acrylic resin emulsion is preferred. As a result of example, these ingredient constitutions can satisfy each of the required performance described above. (I.S.)

  19. Do Fish Resist?

    Directory of Open Access Journals (Sweden)

    Dinesh Joseph Wadiwel

    2016-03-01

    Full Text Available There have been a number of scientific studies on the question of whether fish feel pain. Some have suggested that some fish indeed do feel pain and that this has significant welfare implications (2003. Others have argued that fish do not have the brain development necessary to feel pain. In terms of number of animals killed, the slaughter of sea animals for human consumption significantly exceeds that of any land animals that we use for food, and sea animal slaughter practices frequently lack any basic welfare protections. If fish can be shown to feel pain—or more importantly, if humans can agree that fish feel pain—then this would place a significant question mark over many contemporary fishing practices.  This article substitutes the question 'Do Fish Feel Pain?' with an alternative: 'Do Fish Resist?' It explores the conceptual problems of understanding fish resistance, and the politics of epistemology that surrounds and seeks to develop a conceptual framework for understanding fish resistance to human capture by exploring the development of fishing technologies - the hook, the net and contemporary aquaculture.

  20. Heat resistant protective hand covering

    Science.gov (United States)

    Tschirch, R. P.; Sidman, K. R.; Arons, I. J. (Inventor)

    1984-01-01

    A heat-resistant aromatic polyamide fiber is described. The outer surface of the shell is coated with a fire-resistant elastomer and liner. Generally conforming and secured to the shell and disposed inwardly of the shell, the liner is made of a felt fabric of temperature-resistant aromatic polymide fiber.

  1. Biotechnology: herbicide-resistant crops

    Science.gov (United States)

    Transgenic, herbicide-resistant (HR) crops are planted on about 80% of the land covered by transgenic crops. More than 90% of HR crios are glyphosate-resistant (GR) crops, the others being resistant to glufosinate. The wide-scale adoption of HR crops, largely for economic reasons, has been the mos...

  2. Flow resistance in rod assemblies

    International Nuclear Information System (INIS)

    Korsun, A.S.; Sokolova, M.S.

    2000-01-01

    The general form of relation between the resistance force and the velocity vector, resistance tensor structure and possible types of anisotropy in the flow thorough such structures as rod or tube assemblies are under discussion. Some questions of experimental determination of volumetric resistance force tensor are also under consideration. (author)

  3. Studying Resistance: Some Cautionary Notes

    Science.gov (United States)

    Dimitriadis, Greg

    2011-01-01

    The question of "resistance" has oriented the field of critical ethnography for several generations now. Indeed, the reproduction-resistance binary has animated much of the most important, critical work in educational studies over the last 30 years. Yet, this reproduction-resistance binary has perhaps calcified in recent years. Such work…

  4. Electromigration early resistance increase measurements

    NARCIS (Netherlands)

    Niehof, J.; Flinn, P.A.; Maloney, T.J.

    1993-01-01

    An early resistance change measurement set-up, using an AC bridge technique, has been developed, and measurements have been performed. Large sample-to-sample variations occur. The characteristic time for the resistance change curve is shorter for resistance increase (under current stress) than for

  5. Assessing resistance of stabilized corrosion resistant steels to intergranular corrosion

    International Nuclear Information System (INIS)

    Karas, A.; Cihal, V. Jr.; Vanek, V.; Herzan, J.; Protiva, K.; Cihal, V.

    1987-01-01

    Resistance to intergranular corrosion was determined for four types of titanium-stabilized steels from the coefficients of stabilization efficiency according to the degree the chemical composition was known. The ATA SUPER steel showed the highest resistance parameter value. The resistance of this type of steel of a specific composition, showing a relatively low value of mean nitrogen content was compared with steel of an optimized chemical composition and with low-carbon niobium stabilized, molybdenum modified steels. The comparison showed guarantees of a sufficient resistance of the steel to intergranular corrosion. The method of assessing the resistance to intergranular corrosion using the calculation of the minimum content of Cr', i.e., the effective chromium content, and the maximum effective carbon content C' giving the resistance parameter k seems to be prospective for practical use in the production of corrosion resistant steels. (author). 1 tab., 5 figs., 15 refs

  6. Application of magnetohydrodynamic actuation to continuous flow chemistry.

    Science.gov (United States)

    West, Jonathan; Karamata, Boris; Lillis, Brian; Gleeson, James P; Alderman, John; Collins, John K; Lane, William; Mathewson, Alan; Berney, Helen

    2002-11-01

    Continuous flow microreactors with an annular microchannel for cyclical chemical reactions were fabricated by either bulk micromachining in silicon or by rapid prototyping using EPON SU-8. Fluid propulsion in these unusual microchannels was achieved using AC magnetohydrodynamic (MHD) actuation. This integrated micropumping mechanism obviates the use of moving parts by acting locally on the electrolyte, exploiting its inherent conductive nature. Both silicon and SU-8 microreactors were capable of MHD actuation, attaining fluid velocities of the order of 300 microm s(-1) when using a 500 mM KCl electrolyte. The polymerase chain reaction (PCR), a thermocycling process, was chosen as an illustrative example of a cyclical chemistry. Accordingly, temperature zones were provided to enable a thermal cycle during each revolution. With this approach, fluid velocity determines cycle duration. Here, we report device fabrication and performance, a model to accurately describe fluid circulation by MHD actuation, and compatibility issues relating to this approach to chemistry.

  7. Molecular Detection of Antimicrobial Resistance

    Science.gov (United States)

    Fluit, Ad C.; Visser, Maarten R.; Schmitz, Franz-Josef

    2001-01-01

    The determination of antimicrobial susceptibility of a clinical isolate, especially with increasing resistance, is often crucial for the optimal antimicrobial therapy of infected patients. Nucleic acid-based assays for the detection of resistance may offer advantages over phenotypic assays. Examples are the detection of the methicillin resistance-encoding mecA gene in staphylococci, rifampin resistance in Mycobacterium tuberculosis, and the spread of resistance determinants across the globe. However, molecular assays for the detection of resistance have a number of limitations. New resistance mechanisms may be missed, and in some cases the number of different genes makes generating an assay too costly to compete with phenotypic assays. In addition, proper quality control for molecular assays poses a problem for many laboratories, and this results in questionable results at best. The development of new molecular techniques, e.g., PCR using molecular beacons and DNA chips, expands the possibilities for monitoring resistance. Although molecular techniques for the detection of antimicrobial resistance clearly are winning a place in routine diagnostics, phenotypic assays are still the method of choice for most resistance determinations. In this review, we describe the applications of molecular techniques for the detection of antimicrobial resistance and the current state of the art. PMID:11585788

  8. Antimicrobial resistance of thermophilic Campylobacter

    DEFF Research Database (Denmark)

    Aarestrup, Frank Møller; Engberg, J.

    2001-01-01

    Campylobacter has become the leading cause of zoonotic enteric infections in developed and developing countries world-wide. Antimicrobial resistance has emerged among Campylobacter mainly as a consequence of the use of antimicrobial agents in food animal production. Resistance to drugs of choice...... for the treatment of infections, macrolides and fluoroquinolones has emerged as a clinical problem and interventions to reduce this are recommended. Resistance to fluoroquinolones and macrolides is mediated by chromosomal mutations. Resistance to other relevant antimicrobial agents, mediated by acquired resistance...... genes, has not become widespread so far. However, resistance genes originating from both Gram-positive and Gram-negative bacterial species have been found, showing the potential for acquired resistance to emerge in Campylobacter....

  9. Happy Festivus! Parody as playful consumer resistance

    DEFF Research Database (Denmark)

    Mikkonen, Ilona; Bajde, Domen

    2013-01-01

    Drawing upon literary theory, play and consumer resistance literature, we conceptualize consumer parodic resistance – a resistant form of play that critically refunctions dominant consumption discourses and marketplace ideologies. We explore parodic resistance empirically by analyzing Festivus, a...

  10. Controlling antibiotic resistance in the ICU

    NARCIS (Netherlands)

    Derde, L.P.G.

    2013-01-01

    Patients admitted to intensive care units (ICUs) are frequently colonized with (antibiotic-resistant) bacteria, which may lead to healthcare associated infections. Antimicrobial-resistant bacteria (AMRB), such as methicillin-resistant Staphylococcus aureus (MRSA), vancomycin-resistant Enterococci

  11. Proliferation resistance modeling

    International Nuclear Information System (INIS)

    Bari, R.; Peterson, P.; Roglans, J.; Mladineo, S.; Nuclear Engineering Division; BNL; Univ. of California at Berkely; PNNL

    2004-01-01

    The National Nuclear Security Administration is developing methods for nonproliferation assessments. A working group on Nonproliferation Assessment Methodology (NPAM) assembled a toolbox of methods for various applications in the nonproliferation arena. One application of this methodology is to the evaluation of the proliferation resistance of Generation IV nuclear energy systems. This paper first summarizes the key results of the NPAM program and then provides results obtained thus far in the ongoing application, which is co-sponsored by the DOE Office of Nuclear Energy Science and Technology. In NPAM, a top-level measure of proliferation resistance for a fuel cycle system is developed from a hierarchy of metrics. The problem is decomposed into: metrics to be computed, barriers to proliferation, and a finite set of threats. The analyst models the process undertaken by the proliferant to overcome barriers to proliferation and evaluates the outcomes. In addition to proliferation resistance (PR) evaluation, the application also addresses physical protection (PP) evaluation against sabotage and theft. The Generation IV goal for future nuclear energy systems is to assure that they are very unattractive and the least desirable route for diversion or theft of weapons-usable materials, and provide increased physical protection against terrorism. An Expert Group, addressing this application, has identified six high-level measures for the PR goals (six measures have also been identified for the PP goals). Combined together, the complete set of measures provides information for program policy makers and system designers to compare specific system design features and integral system characteristics and to make choices among alternative options. The Group has developed a framework for a phased evaluation approach to analyzing PR and PP of system characteristics and to quantifying metrics and measures. This approach allows evaluations to become more detailed and representative

  12. NEW RADIATION RESISTANT GREASES

    Energy Technology Data Exchange (ETDEWEB)

    DasGupta, Sharda; Slobodian, J. T.

    1962-11-20

    New radiation resistant greases were prepared from commercially available greases by carrying out radioinduced reactions with styrene. The radiation tolerances of the products were 250-1000 fold more than the starting materials and any product of similar properties now available. The various properties of the new products initially and after exposure to large radiation doses were in no case inferior to the original greases and in some respects improvements were observed. Radiation tolerance of commercial greases could be enhanced by the addition of polystyrene to form a physical mixture rather than copolymers. The reaction mechanisms involved at all stages were studied using infrared spectroscopic techniques. (P.C.H.)

  13. Tunable resistance coatings

    Science.gov (United States)

    Elam, Jeffrey W.; Mane, Anil U.

    2015-08-11

    A method and article of manufacture of intermixed tunable resistance composite materials containing at least one of W:Al.sub.2O.sub.3, Mo:Al.sub.2O.sub.3 or M:Al.sub.2O.sub.3 where M is a conducting compound containing either W or Mo. A conducting material and an insulating material are deposited by such methods as ALD or CVD to construct composites with intermixed materials which do not have structure or properties like their bulk counterparts.

  14. Multidrug resistant Fusarium keratitis.

    Science.gov (United States)

    Antequera, P; Garcia-Conca, V; Martín-González, C; Ortiz-de-la-Tabla, V

    2015-08-01

    We report a case of keratitis in a female contact lens wearer, who developed a deep corneal abscess. The culture of a corneal biopsy scraping was positive for multiresistant Fusarium solani. The patient has a complicated clinical course and failed to respond to local and systemic antifungal treatment, requiring eye enucleation. Fusarium keratitis may progress to severe endophthalmitis. Clinical suspicion is paramount in order to start antifungal therapy without delay. Therapy is complex due to the high resistance of this organism to usual antifungal drugs. Copyright © 2014 Sociedad Española de Oftalmología. Published by Elsevier España, S.L.U. All rights reserved.

  15. Surface Functionalization of Epoxy-Resist- Based Microcantilevers with Iron Oxide Nanocrystals

    DEFF Research Database (Denmark)

    Ingrosso, Chiara; Sardella, E.; Keller, Stephan Sylvest

    2010-01-01

    A functionalization procedure is integrated in the fabrication of micromechanical SU-8 cantilevers in order to chemically bind organic-capped Fe2O3 NCs at the photoresist surface, under visible light, ambient atmosp here and room temperature. The achieved highly interconnected NC multilayer netwo...... is demonstrated an active layer for real-time detection of acetone vapor molecules....

  16. Measuring The Contact Resistances Of Photovoltaic Cells

    Science.gov (United States)

    Burger, D. R.

    1985-01-01

    Simple method devised to measure contact resistances of photovoltaic solar cells. Method uses readily available equipment and applicable at any time during life of cell. Enables evaluation of cell contact resistance, contact-end resistance, contact resistivity, sheet resistivity, and sheet resistivity under contact.

  17. Outwitting the series resistance in scanning spreading resistance microscopy

    International Nuclear Information System (INIS)

    Schulze, A.; Cao, R.; Eyben, P.; Hantschel, T.; Vandervorst, W.

    2016-01-01

    The performance of nanoelectronics devices critically depends on the distribution of active dopants inside these structures. For this reason, dopant profiling has been defined as one of the major metrology challenges by the international technology roadmap of semiconductors. Scanning spreading resistance microscopy (SSRM) has evolved as one of the most viable approaches over the last decade due to its excellent spatial resolution, sensitivity and quantification accuracy. However, in case of advanced device architectures like fins and nanowires a proper measurement of the spreading resistance is often hampered by the increasing impact of parasitic series resistances (e.g. bulk series resistance) arising from the confined nature of the aforementioned structures. In order to overcome this limitation we report in this paper the development and implementation of a novel SSRM mode (fast Fourier transform-SSRM: FFT-SSRM) which essentially decouples the spreading resistance from parasitic series resistance components. We show that this can be achieved by a force modulation (leading to a modulated spreading resistance signal) in combination with a lock-in deconvolution concept. In this paper we first introduce the principle of operation of the technique. We discuss in detail the underlying physical mechanisms as well as the technical implementation on a state-of-the-art atomic force microscope (AFM). We demonstrate the performance of FFT-SSRM and its ability to remove substantial series resistance components in practice. Eventually, the possibility of decoupling the spreading resistance from the intrinsic probe resistance will be demonstrated and discussed. - Highlights: • A novel electrical AFM mode for carrier profiling in confined volumes is presented. • Thereby the force and hence the contact area between AFM probe and sample is modulated. • Information on the spreading resistance is derived using a lock-in approach. • Bulk series resistance components are

  18. Relaxation resistance of heat resisting alloys with cobalt

    International Nuclear Information System (INIS)

    Borzdyka, A.M.

    1977-01-01

    Relaxation resistance of refractory nickel-chromium alloys containing 5 to 14 % cobalt is under study. The tests involve the use of circular samples at 800 deg to 850 deg C. It is shown that an alloy containing 14% cobalt possesses the best relaxation resistance exceeding that of nickel-chromium alloys without any cobalt by a factor of 1.5 to 2. The relaxation resistance of an alloy with 5% cobalt can be increased by hardening at repeated loading

  19. A resistência olha a resistência

    Directory of Open Access Journals (Sweden)

    Jorge Ponciano Ribeiro

    Full Text Available Resistência é um processo humano que acontece quando a pessoa se encontra sob algum tipo de ameaça. Não é essencialmente um acontecimento psicoterapêutico. Ocorre na terapia não como uma oposição a si mesmo ou ao terapeuta, mas como uma forma de se ajustar a uma nova situação. A resistência, é por natureza, a atualização do instinto de auto-preservação. E o organismo inteligentemente segue a lei da preferência. Resistência é uma forma de contato que não pode ser destruída, mas administrada, porque ela surge como uma defesa da totalidade vivenciada pela pessoa. A Resistência é, às vezes, resistência e awareness mais que ao contato. Ela revela mais o caminho seguido do que oculta a caminhada feita. A resistência é um processo natural, porque o corpo que não resiste, morre, mas falamos em processos de auto-regulação organísmica. Valorizamos mais o que mantêm a resistência funcionando do que à própria resistência. O terapeuta também resiste, ou seja, ele se auto-regula na sua relação com o cliente. Não questionamos a resistência, mas o processo que a mantêm. Trabalhamos com nove mecanismos de defesa, também tradicionalmente, chamados de resistência.

  20. Corrosion resistant cemented carbide

    International Nuclear Information System (INIS)

    Hong, J.

    1990-01-01

    This paper describes a corrosion resistant cemented carbide composite. It comprises: a granular tungsten carbide phase, a semi-continuous solid solution carbide phase extending closely adjacent at least a portion of the grains of tungsten carbide for enhancing corrosion resistance, and a substantially continuous metal binder phase. The cemented carbide composite consisting essentially of an effective amount of an anti-corrosion additive, from about 4 to about 16 percent by weight metal binder phase, and with the remaining portion being from about 84 to about 96 percent by weight metal carbide wherein the metal carbide consists essentially of from about 4 to about 30 percent by weight of a transition metal carbide or mixtures thereof selected from Group IVB and of the Periodic Table of Elements and from about 70 to about 96 percent tungsten carbide. The metal binder phase consists essentially of nickel and from about 10 to about 25 percent by weight chromium, the effective amount of an anti-corrosion additive being selected from the group consisting essentially of copper, silver, tine and combinations thereof

  1. Oxidation Resistant Graphite Studies

    Energy Technology Data Exchange (ETDEWEB)

    W. Windes; R. Smith

    2014-07-01

    The Very High Temperature Reactor (VHTR) Graphite Research and Development Program is investigating doped nuclear graphite grades exhibiting oxidation resistance. During a oxygen ingress accident the oxidation rates of the high temperature graphite core region would be extremely high resulting in significant structural damage to the core. Reducing the oxidation rate of the graphite core material would reduce the structural effects and keep the core integrity intact during any air-ingress accident. Oxidation testing of graphite doped with oxidation resistant material is being conducted to determine the extent of oxidation rate reduction. Nuclear grade graphite doped with varying levels of Boron-Carbide (B4C) was oxidized in air at nominal 740°C at 10/90% (air/He) and 100% air. The oxidation rates of the boronated and unboronated graphite grade were compared. With increasing boron-carbide content (up to 6 vol%) the oxidation rate was observed to have a 20 fold reduction from unboronated graphite. Visual inspection and uniformity of oxidation across the surface of the specimens were conducted. Future work to determine the remaining mechanical strength as well as graphite grades with SiC doped material are discussed.

  2. [Resistant hypertension: An update].

    Science.gov (United States)

    Renna, N F

    2018-02-04

    An estimated 10% to 20% of hypertensive patients could be considered resistant to treatment (RH). These are patients who are not controlled using three drugs, at the maximum tolerated doses, including a diuretic, as well as those with high blood pressure controlled using four or more drugs. The term is used to identify patients that might benefit from special diagnostic and/or therapeutic consideration. The term 'refractory hypertension' has recently been proposed as a novel phenotype of antihypertensive failure. It refers to patients whose blood pressure cannot be controlled with maximum treatment. The first studies of this phenotype indicate that it is rare and affects less than 5% of patients with RH. Adherence to or compliance with medical treatment is key to defining resistant hypertension. Closer attention has been paid to clinical and experimental research since the first scientific statement for the diagnosis, assessment and treatment of RH from the American Heart Association, and in the European guidelines, was published in 2008. This review will set out the concepts relating to prevalence, prognosis and compliance and cover the latest developments on this subject. Copyright © 2018 SEH-LELHA. Publicado por Elsevier España, S.L.U. All rights reserved.

  3. Resistive Memory Devices for Radiation Resistant Non-Volatile Memory

    Data.gov (United States)

    National Aeronautics and Space Administration — Ionizing radiation in space can damage electronic equipment, corrupting data and even disabling computers. Radiation resistant (rad hard) strategies must be employed...

  4. The Prehistory of Antibiotic Resistance.

    Science.gov (United States)

    Perry, Julie; Waglechner, Nicholas; Wright, Gerard

    2016-06-01

    Antibiotic resistance is a global problem that is reaching crisis levels. The global collection of resistance genes in clinical and environmental samples is the antibiotic "resistome," and is subject to the selective pressure of human activity. The origin of many modern resistance genes in pathogens is likely environmental bacteria, including antibiotic producing organisms that have existed for millennia. Recent work has uncovered resistance in ancient permafrost, isolated caves, and in human specimens preserved for hundreds of years. Together with bioinformatic analyses on modern-day sequences, these studies predict an ancient origin of resistance that long precedes the use of antibiotics in the clinic. Understanding the history of antibiotic resistance is important in predicting its future evolution. Copyright © 2016 Cold Spring Harbor Laboratory Press; all rights reserved.

  5. Persistence, resistance, resonance

    Science.gov (United States)

    Tsadka, Maayan

    Sound cannot travel in a vacuum, physically or socially. The ways in which sound operates are a result of acoustic properties, and the ways by which it is considered to be music are a result of social constructions. Therefore, music is always political, regardless of its content: the way it is performed and composed; the choice of instrumentation, notation, tuning; the medium of its distribution; its inherent hierarchy and power dynamics, and more. My compositional praxis makes me less interested in defining a relationship between music and politics than I am in erasing---or at least blurring---the borders between them. In this paper I discuss the aesthetics of resonance and echo in their metaphorical, physical, social, and musical manifestations. Also discussed is a political aesthetic of resonance, manifested through protest chants. I transcribe and analyze common protest chants from around the world, categorizing and unifying them as universal crowd-mobilizing rhythms. These ideas are explored musically in three pieces. Sumud: Rhetoric of Resistance in Three Movements, for two pianos and two percussion players, is a musical interpretation of the political/social concept of sumud, an Arabic word that literally means "steadfastness" and represents Palestinian non-violent resistance. The piece is based on common protest rhythms and uses the acoustic properties inherent to the instruments. The second piece, Three Piano Studies, extends some of the musical ideas and techniques used in Sumud, and explores the acoustic properties and resonance of the piano. The final set of pieces is part of my Critical Mess Music Project. These are site-specific musical works that attempt to blur the boundaries between audience, performers and composer, in part by including people without traditional musical training in the process of music making. These pieces use the natural structure and resonance of an environment, in this case, locations on the UCSC campus, and offer an active

  6. Observations on resistive wall modes

    International Nuclear Information System (INIS)

    Gerwin, R.A.; Finn, J.M.

    1996-01-01

    Several results on resistive wall modes and their application to tokamaks are presented. First, it is observed that in the presence of collisional parallel dynamics there is an exact cancellation to lowest order of the dissipative and sound wave effects for an ideal Ohm's law. This is easily traced to the fact that the parallel dynamics occurs along the perturbed magnetic field lines for such electromagnetic modes. Such a cancellation does not occur in the resistive layer of a tearing-like mode. The relevance to models for resistive wall modes using an electrostatic Hammett-Perkins type operator to model Landau damping will be discussed. Second, we observe that with an ideal Ohm's law, resistive wall modes can be destabilized by rotation in that part of parameter space in which the ideal MHD modes are stable with the wall at infinity. This effect can easily be explained by interpreting the resistive wall instability in terms of mode coupling between the backward stable MHD mode and a stable mode locked into the wall. Such an effect can occur for very small rotation for tearing-resistive wall modes in which inertia dominates viscosity in the layer, but the mode is stabilized by further rotation. For modes for which viscosity dominates in the layer, rotation is purely stabilizing. For both tearing models, a somewhat higher rotation frequency gives stability essentially whenever the tearing mode is stable with a perfectly conducting wall. These tearing/resistive wall results axe also simply explained in terms of mode coupling. It has been shown that resonant external ideal modes can be stabilized in the presence of resistive wall and resistive plasma with rotation of order the nominal tearing mode growth rate. We show that these modes behave as resistive wall tearing modes in the sense above. This strengthens the suggestion that rotational stabilization of the external kink with a resistive wall is due to the presence of resistive layers, even for ideal modes

  7. Profiling Prostate Cancer Therapeutic Resistance

    OpenAIRE

    Cameron A. Wade; Natasha Kyprianou

    2018-01-01

    The major challenge in the treatment of patients with advanced lethal prostate cancer is therapeutic resistance to androgen-deprivation therapy (ADT) and chemotherapy. Overriding this resistance requires understanding of the driving mechanisms of the tumor microenvironment, not just the androgen receptor (AR)-signaling cascade, that facilitate therapeutic resistance in order to identify new drug targets. The tumor microenvironment enables key signaling pathways promoting cancer cell survival ...

  8. Adipokines and Hepatic Insulin Resistance

    Science.gov (United States)

    Hassan, Waseem

    2013-01-01

    Obesity is a major risk factor for insulin resistance and type 2 diabetes. Adipose tissue is now considered to be an active endocrine organ that secretes various adipokines such as adiponectin, leptin, resistin, tumour necrosis factor-α, and interleukin-6. Recent studies have shown that these factors might provide a molecular link between increased adiposity and impaired insulin sensitivity. Since hepatic insulin resistance plays the key role in the whole body insulin resistance, clarification of the regulatory processes about hepatic insulin resistance by adipokines in rodents and human would seem essential in order to understand the mechanism of type 2 diabetes and for developing novel therapeutic strategies to treat it. PMID:23762871

  9. Antibiotics and the resistant microbiome

    DEFF Research Database (Denmark)

    Sommer, Morten; Dantas, Gautam

    2011-01-01

    . Less appreciated are the concomitant changes in the human microbiome in response to these assaults and their contribution to clinical resistance problems. Studies have shown that pervasive changes to the human microbiota result from antibiotic treatment and that resistant strains can persist for years....... Additionally, culture-independent functional characterization of the resistance genes from the microbiome has demonstrated a close evolutionary relationship between resistance genes in the microbiome and in pathogens. Application of these techniques and novel cultivation methods are expected to significantly...... expand our understanding of the interplay between antibiotics and the microbiome....

  10. Rhythms of Resistance and Existence

    DEFF Research Database (Denmark)

    Chaudhary, Nandita; Hviid, Pernille; Marsico, Giuseppina

    2017-01-01

    This book is about resistance in everyday life, illustrated through empirical contexts from different parts of the world. Resistance is a widespread phenomenon in biological, social and psychological domains of human cultural development. Yet, it is not well articulated in the academic literature...... occurrence, the focus here is on everyday resistance as an intentional process where new meaning constructions emerge in thinking, feeling, acting or simply living with others. Resistance is thus conceived as a meaning-making activity that operates at the intersection of personal and collective systems...

  11. Resistance to Barley Leaf Stripe

    DEFF Research Database (Denmark)

    Nørgaard Knudsen, J. C.

    1986-01-01

    in well adapted Northwest European spring cultivars. Virulence matching two hitherto not overcome resistances was demonstrated. Differences in apparent race nonspecific or partial resistance were also present, changing the percentage of infected plants of susceptible genotypes from about 20 to 44 per cent.......Ten barley [Hordeum vulgare] genotypes were inoculated with twelve isolates of Pyrenophora graminea of diverse European and North African origin. Race specific resistance occurred. Four, possibly five, genetically different sources of race-specific resistance were found, three of them occurring...

  12. Organic ice resists

    DEFF Research Database (Denmark)

    Tiddi, William; Elsukova, Anna; Le, Hoa Thanh

    2017-01-01

    Electron-beam lithography (EBL) is the backbone technology for patterning nanostructures and manufacturing nanodevices. It involves processing and handling synthetic resins in several steps, each requiring optimization and dedicated instrumentation in cleanroom environments. Here, we show...... that simple organic molecules, e.g. alcohols, condensed to form thin-films at low temperature demonstrate resist-like capabilities for EBL applications and beyond. The entire lithographic process takes place in a single instrument, and avoids exposing chemicals to the user and the need of cleanrooms. Unlike...... EBL that requires large samples with optically flat surfaces, we patterned on fragile membranes only 5-nm-thin, and 2 x 2 mm2 diamond samples. We created patterns on the nm to sub-mm scale, as well as three-dimensional structures by stacking layers of frozen organic molecules. Finally, using plasma...

  13. Powdery Mildew Disease Resistance

    Energy Technology Data Exchange (ETDEWEB)

    Somerville, Shauna C.

    2010-08-31

    The overall goal of this project was to characterize the PMR5 protein, a member of the DUF231/TBR family, and to determine its role in plant cell wall biogenesis. Since the pmr5 mutants are also resistant to the fungal powdery mildew pathogen, we wished to determine what specific cell wall changes are associated with disease resistance and why. The graduate student working on this project made mutations in the putative active site of PMR5, assuming it is a member of the SGNH/GDSL esterase superfamily (Anantharaman and Aravind, 2010, Biology Direct 5, 1). These mutants were inactive in planta suggesting that PMR5 is a functional enzyme and not a binding protein or chaperone. In addition, she determined that cell wall preparations from the pmr5 mutant exhibited a modest reduction (13%) in total acetyl groups. To pursue characterization further, the graduate student expressed the PMR5 protein in a heterologous E. coli system. She could purify PMR5 using a two step protocol based on tags added to the N and C terminus of the protein. She was able to show the PMR5 protein bound to pectins, including homogalacturonan, but not to other cell wall components (e.g., xyloglucans, arabinans). Based on these observations, a postdoctoral fellow is currently developing an enzyme assay for PMR5 based on the idea that it may be acetylating the homogalacturonic acid pectin fraction. Our initial experiments to localize PMR5 subcellularly suggested that it occurred in the endoplasmic reticulum. However, since the various pectins are believed to be synthesized in the Golgi apparatus, we felt it necessary to repeat our results using a native promoter expression system. Within the past year, we have demonstrated conclusively that PMR5 is localized to the endoplasmic reticulum, a location that sets it apart from most cell wall biogenesis and modification enzymes. The graduate student contributed to the characterization of two suppressor mutants, which were selected as restoring powdery

  14. plasmid mediated resistance in multidrug resistant bacteria isolated

    African Journals Online (AJOL)

    User

    PLASMID MEDIATED RESISTANCE IN MULTIDRUG RESISTANT BACTERIA. ISOLATED FROM CHILDREN WITH SUSPECTED SEPTICAEMIA IN ZARIA,. NIGERIA. AbdulAziz, Z. A.,1* Ehinmidu, J. O.,1 Adeshina, G. O.,1 Pala, Y. Y2., Yusuf, S. S2. and. Bugaje, M. A.3. 1Department of Pharmaceutics and Pharmaceutical ...

  15. Electrical resistivity measurements to predict abrasion resistance of ...

    Indian Academy of Sciences (India)

    WINTEC

    increasing expansion of highway and other construction works and decreasing natural aggregate resources in the world, the demand for crushed stone aggregates has in- creased from day-to-day. One of the important properties of rock aggregates is abrasion resistance. The abrasion resistance of aggregates is generally ...

  16. Vancomycin Resistance in Staphylococcus aureus


    Science.gov (United States)

    McGuinness, Will A.; Malachowa, Natalia; DeLeo, Frank R.

    2017-01-01

    The evolution of Staphylococcus aureus during the modern antibiotic era has been delineated by distinct strain emergence events, many of which include acquisition of antibiotic resistance. The relative high burden of methicillin-resistant S. aureus (MRSA) in healthcare and community settings is a major concern worldwide. Vancomycin, a glycopeptide antibiotic that inhibits cell wall biosynthesis, remains a drug of choice for treatment of severe MRSA infections. S. aureus strains exhibiting increased resistance to vancomycin, known as vancomycin intermediate-resistant S. aureus (VISA) (MIC = 4-8 µg/mL), were discovered in the 1990s. The molecular basis of resistance in VISA is polygenic and involves stepwise mutations in genes encoding molecules predominantly involved in cell envelope biosynthesis. S. aureus isolates with complete resistance to vancomycin (MIC ≥ 16 µg/mL) are termed vancomycin-resistant S. aureus (VRSA)—they were first reported in the U.S. in 2002. Resistance in VRSA is conferred by the vanA gene and operon, which is present on a plasmid. Although treatment of VRSA infections is challenging, the total number of human VRSA infections to date is limited (14 in the U.S.). By comparison, the burden of VISA is relatively high and the molecular mechanisms of resistance are less well-defined. VISA are associated with persistent infections, vancomycin treatment failure, and poor clinical outcomes. Here, we review in brief progress made toward understanding the acquisition of antibiotic resistance in S. aureus, with an emphasis on the molecular mechanisms underlying vancomycin resistance. PMID:28656013

  17. Reconceptualizing resistance: sociology and the affective dimension of resistance.

    Science.gov (United States)

    Hynes, Maria

    2013-12-01

    This paper re-examines the sociological study of resistance in light of growing interest in the concept of affect. Recent claims that we are witness to an 'affective turn' and calls for a 'new sociological empiricism' sensitive to affect indicate an emerging paradigm shift in sociology. Yet, mainstream sociological study of resistance tends to have been largely unaffected by this shift. To this end, this paper presents a case for the significance of affect as a lens by which to approach the study of resistance. My claim is not simply that the forms of actions we would normally recognize as resistance have an affective dimension. Rather, it is that the theory of affect broadens 'resistance' beyond the purview of the two dominant modes of analysis in sociology; namely, the study of macropolitical forms, on the one hand, and the micropolitics of everyday resistance on the other. This broadened perspective challenges the persistent assumption that ideological forms of power and resistance are the most pertinent to the contemporary world, suggesting that much power and resistance today is of a more affective nature. In making this argument, it is a Deleuzian reading of affect that is pursued, which opens up to a level of analysis beyond the common understanding of affect as emotion. I argue that an affective approach to resistance would pay attention to those barely perceptible transitions in power and mobilizations of bodily potential that operate below the conscious perceptions and subjective emotions of social actors. These affective transitions constitute a new site at which both power and resistance operate. © London School of Economics and Political Science 2013.

  18. METHICILLIN RESISTANCE IN STAPHYLOCOCCAL ISOLATES ...

    African Journals Online (AJOL)

    The study assessed the importance of Staphylococcus aureus as a urinary pathogen and the incidence of multidrug resistant (MDR), methicillin-resistant Staphylococcus aureus (MRSA). A total of 86 staphylococcal isolates made up of 50 clinical isolates from urine samples submitted to the Medical Microbiology Laboratory ...

  19. Resistance, Reinhabitation, and Regime Change

    Science.gov (United States)

    Gruenewald, David

    2006-01-01

    How do individuals know when, and what, to resist? Alan Schoenfeld, in the March 2006 issue of "Educational Researcher," tells a story of resistance that all math educators, and all curriculum specialists, need to consider. Schoenfeld titled his story, "What Doesn't Work: The Challenge and Failure of the What Works Clearinghouse to Conduct…

  20. PREVALENCE AND ANTIBIOTIC RESISTANCE OF ...

    African Journals Online (AJOL)

    9 mars 2015 ... strategy to prevent the spread of this resistance. Keywords: Staphylococci; Staphylococcus aureus; Oxacillin; Antibiotic resistance; Disc diffusion. Author Correspondence, e-mail: mn.boukhatem@yahoo.fr. ICID: 1142924. Journal of Fundamental and Applied Sciences. ISSN 1112-9867. Available online at.

  1. Wear resistance of cast iron

    Directory of Open Access Journals (Sweden)

    S. Pietrowski

    2008-10-01

    Full Text Available In this paper investigations of abrasive and adhesive wear resistance of different cast iron grades have been presented. Examinations showed, that the most advantageous pair of materials is the cast iron – the hardened steel with low-tempered martensite. It was found, that martensitic nodular cast iron with carbides is the most resistant material.

  2. Helping Teens Resist Sexual Pressure

    Science.gov (United States)

    ... Listen Español Text Size Email Print Share Helping Teens Resist Sexual Pressure Page Content Article Body Teens are more ... younger the first time they had intercourse. Helping Teens Resist Sexual Pressure “The pressure on teenagers to have sex ...

  3. Dealing with Resistance to Change

    Science.gov (United States)

    Williamson, Ronald; Blackburn, Barbara R.

    2010-01-01

    One of the biggest roadblocks to addressing instructional rigor in schools is the resistance to change that is displayed by teachers, students, parents, and other building and district leaders. Every person deals differently with change. Some are more accepting, others more resistant. No change is successful if the people being asked to change…

  4. Multidrug resistance in Lactococcus lactis

    NARCIS (Netherlands)

    Bolhuis, Hendrik

    1996-01-01

    Multidrug resistance (MDR) was initially recongnized as the major cause of the failure of the drug-based treatment of human cancers. It has become increasingly clear that MDR occurs in mammalian cells but also in lower eukaryotes and bacteria. The appearance of multiple antibiotic resistant

  5. Adriamycin resistance and radiation response

    International Nuclear Information System (INIS)

    Belli, J.A.; Harris, J.R.

    1979-01-01

    Mammalian cells (V79) in culture developed resistance to Adriamycin during continuous exposure to low levels of drug. This resistance was accompanied by change in x-ray survival properties which, in turn, depended upon the isolation of subpopulations from resistant sub lines. These changes in x-ray survival properties were characterized by reduced D/sub Q/ values and a decrease in the D/sub O/. However, these changes were not observed together in the same cell sub line. Adriamycin-resistant cells did not appear to be radiation damage repair deficient. Other phenotypic changes (cell morphology, DNA content and chromosome number) suggested mutational events coincident with the development of Adriamycin resistance

  6. The (Street) Art of Resistance

    DEFF Research Database (Denmark)

    Awad, Sarah H.; Wagoner, Brady; Glaveanu, Vlad Petre

    2017-01-01

    This chapter focuses on the interrelation between resistance, novelty and social change We will consider resistance as both a social and individual phenomenon, a constructive process that articulates continuity and change and as an act oriented towards an imagined future of different communities....... In this account, resistance is thus a creative act having its own dynamic and, most of all, aesthetic dimension. In fact, it is one such visibly artistic form of resistance that will be considered here, the case of street art as a tool of social protest and revolution in Egypt. Street art is commonly defined...... in sharp contrast with high or fine art because of its collective nature and anonymity, its different kind of aesthetics, and most of all its disruptive, ‘anti-social’ outcomes. With the use of illustrations, we will argue here that street art is prototypical of a creative form of resistance, situated...

  7. Resistive instabilities in tokamaks

    International Nuclear Information System (INIS)

    Rutherford, P.H.

    1985-10-01

    Low-m tearing modes constitute the dominant instability problem in present-day tokamaks. In this lecture, the stability criteria for representative current profiles with q(0)-values slightly less than unit are reviewed; ''sawtooth'' reconnection to q(0)-values just at, or slightly exceeding, unity is generally destabilizing to the m = 2, n = 1 and m = 3, n = 2 modes, and severely limits the range of stable profile shapes. Feedback stabilization of m greater than or equal to 2 modes by rf heating or current drive, applied locally at the magnetic islands, appears feasible; feedback by island current drive is much more efficient, in terms of the radio-frequency power required, then feedback by island heating. Feedback stabilization of the m = 1 mode - although yielding particularly beneficial effects for resistive-tearing and high-beta stability by allowing q(0)-values substantially below unity - is more problematical, unless the m = 1 ideal-MHD mode can be made positively stable by strong triangular shaping of the central flux surfaces. Feedback techniques require a detectable, rotating MHD-like signal; the slowing of mode rotation - or the excitation of non-rotating modes - by an imperfectly conducting wall is also discussed

  8. Upper airway resistance syndrome.

    Science.gov (United States)

    Montserrat, J M; Badia, J R

    1999-03-01

    This article reviews the clinical picture, diagnosis and management of the upper airway resistance syndrome (UARS). Presently, there is not enough data on key points like the frequency of UARS and the morbidity associated with this condition. Furthermore, the existence of LIARS as an independent sleep disorder and its relation with snoring and obstructive events is in debate. The diagnosis of UARS is still a controversial issue. The technical limitations of the classic approach to monitor airflow with thermistors and inductance plethysmography, as well as the lack of a precise definition of hypopnea, may have led to a misinterpretation of UARS as an independent diagnosis from the sleep apnea/hypopnea syndrome. The diagnosis of this syndrome can be missed using a conventional polysomnographic setting unless appropriate techniques are applied. The use of an esophageal balloon to monitor inspiratory effort is currently the gold standard. However, other sensitive methods such as the use of a pneumotachograph and, more recently, nasal cannula/pressure transducer systems or on-line monitoring of respiratory impedance with the forced oscillation technique may provide other interesting possibilities. Recognition and characterization of this subgroup of patients within sleep breathing disorders is important because they are symptomatic and may benefit from treatment. Management options to treat UARS comprise all those currently available for sleep apnea/hypopnea syndrome (SAHS). However, the subset of patients classically identified as LIARS that exhibit skeletal craneo-facial abnormalities might possibly obtain further benefit from maxillofacial surgery.

  9. Radiation resistance of elastomers

    International Nuclear Information System (INIS)

    Hourquebie, P.; Bigarre, J.; Forveille, J.L.; Raby, J.; Lazare, L.

    2002-01-01

    The COMOR group is a network of laboratories from both the CEA and the CNRS. This network is particularly involved in fundamental and applied studies on the ageing of polymers under irradiation. COMOR has studied the ageing of EPDM (ethylene-propylene-diene-monomer) because this elastomer is often used in nuclear environment (in cable coating for instance). In this study, we have prepared materials with different formulations and we have characterised their use-condition properties (dielectric and mechanical) before and after γ irradiation. The dielectric measurements are well adapted to study the oxidation and the crosslinking phenomena which appear during the irradiation ageing. We have shown that after a short time, the oxidation is limited by the diffusion of oxygen. A phenolic antioxidant is not able to protect the polymer against the oxidation. However, we used a concentration typical of a purely thermal stabilisation case (0,1%). On the other hand, a diamine type additive with a concentration of 1% showed efficient stabilisation. The mechanical properties of the regular EPDM are strongly affected by the irradiation but there is little difference with regard to radiation resistance between both types of raw materials. Nevertheless, the NORDEL IP 3725 stabilised with the amine has better initial mechanical properties whereas the NORDEL 2722 offers higher strength above 300 kGy. Our results emphasize the stake of a proper stabilisation of polymers with respect to ionising radiation. (authors)

  10. [Unconscious resistance to contraception].

    Science.gov (United States)

    Gloor, P A

    1978-12-01

    The Swiss penal code of 1942 requires the presence of a psychiatrist in all decisions about termination of pregnancy and of sterilization. The so called sexual revolution of the last 20 years has brought about a dissociation of the traditional psychosexual behavior, where eroticism, affection, and desire of a child do not integrate as harmoniously as before. Narcissistic libido, inherent in all of us, can make an individual want a baby for reasons other than normal, but as a reflection of a parent, as a toy for an infantile mother, as a termination to free, sexual life, felt as sin, for a young couple, as a hope for the future, as the rival of one of the parents, as a remedy for something lost. These are just some of the reasons why contraception, completely accepted on a conscious level, can be rejected on an unconscious one, leading to unwanted pregnancies. Family planning, through a better and deeper psychological preparation of its personnel, should better identify patients more at risk of contraceptive failure, and the unconscious resistances of individuals and couples. This very important task can be started in schools with sex education, and in family planning centers with sexual therapy for the couple. This new approach would imply an increased interest for psychology on the part of doctors assisting young couples.

  11. Measurement of Dynamic Resistance in Resistance Spot Welding

    DEFF Research Database (Denmark)

    Wu, Pei; Lu, J.; Zhang, Wenqi

    2007-01-01

    is influenced by inductive noise caused by the high welding current. In this study, the dynamic resistance is determined by measuring the voltage at primary side and current at secondary side. This increases the accuracy of measurement because of higher signal-noise ratio, and allows to apply to in-process......The conventional methods of determining the dynamic resistance were mostly done by measuring the voltage and current at secondary side of transformer in resistance welding machines, in which the measuring set-up normally interferes with the movement of electrode, and the measuring precision...

  12. Resistance patterns, prevalence, and predictors of fluoroquinolones resistance in multidrug resistant tuberculosis patients

    Directory of Open Access Journals (Sweden)

    Nafees Ahmad

    2016-01-01

    Conclusion: The high degree of drug resistance observed, particularly to fluoroquinolones, is alarming. We recommend the adoption of more restrictive policies to control non-prescription sale of fluoroquinolones, its rational use by physicians, and training doctors in both private and public–private mix sectors to prevent further increase in fluoroquinolones resistant Mycobacterium tuberculosis strains.

  13. Glyphosate resistance: state of knowledge

    Science.gov (United States)

    Sammons, Robert Douglas; Gaines, Todd A

    2014-01-01

    Studies of mechanisms of resistance to glyphosate have increased current understanding of herbicide resistance mechanisms. Thus far, single-codon non-synonymous mutations of EPSPS (5-enolypyruvylshikimate-3-phosphate synthase) have been rare and, relative to other herbicide mode of action target-site mutations, unconventionally weak in magnitude for resistance to glyphosate. However, it is possible that weeds will emerge with non-synonymous mutations of two codons of EPSPS to produce an enzyme endowing greater resistance to glyphosate. Today, target-gene duplication is a common glyphosate resistance mechanism and could become a fundamental process for developing any resistance trait. Based on competition and substrate selectivity studies in several species, rapid vacuole sequestration of glyphosate occurs via a transporter mechanism. Conversely, as the chloroplast requires transporters for uptake of important metabolites, transporters associated with the two plastid membranes may separately, or together, successfully block glyphosate delivery. A model based on finite glyphosate dose and limiting time required for chloroplast loading sets the stage for understanding how uniquely different mechanisms can contribute to overall glyphosate resistance. PMID:25180399

  14. Cephalosporin resistance in Neisseria gonorrhoeae

    Directory of Open Access Journals (Sweden)

    Manju Bala

    2010-01-01

    Full Text Available Gonorrhea, a disease of public health importance, not only leads to high incidence of acute infections and complications but also plays a major role in facilitating human immunodeficiency virus (HIV acquisition and transmission. One of the major public health needs for gonorrhea control is appropriate, effective treatment. However, treatment options for gonorrhea are diminishing as Neisseria gonorrhoeae have developed resistance to several antimicrobial drugs such as sulfonamides, penicillin, tetracyclines and quinolones. Antimicrobial resistance (AMR surveillance of N. gonorrhoeae helps establish and maintain the efficacy of standard treatment regimens. AMR surveillance should be continuous to reveal the emergence of new resistant strains, monitor the changing patterns of resistance, and be able to update treatment recommendations so as to assist in disease control. Current treatment guidelines recommend the use of single dose injectable or oral cephalosporins. The emergence and spread of cephalosporin resistant and multi drug resistant N. gonorrhoeae strains, represents a worrying trend that requires monitoring and investigation. Routine clinical laboratories need to be vigilant for the detection of such strains such that strategies for control and prevention could be reviewed and revised from time to time. It will be important to elucidate the genetic mechanisms responsible for decreased susceptibility and future resistance. There is also an urgent need for research of safe, alternative anti-gonococcal compounds that can be administered orally and have effective potency, allowing high therapeutic efficacy (greater than 95.0% cure rate.

  15. Antibiotic resistance in Burkholderia species.

    Science.gov (United States)

    Rhodes, Katherine A; Schweizer, Herbert P

    2016-09-01

    The genus Burkholderia comprises metabolically diverse and adaptable Gram-negative bacteria, which thrive in often adversarial environments. A few members of the genus are prominent opportunistic pathogens. These include Burkholderia mallei and Burkholderia pseudomallei of the B. pseudomallei complex, which cause glanders and melioidosis, respectively. Burkholderia cenocepacia, Burkholderia multivorans, and Burkholderia vietnamiensis belong to the Burkholderia cepacia complex and affect mostly cystic fibrosis patients. Infections caused by these bacteria are difficult to treat because of significant antibiotic resistance. The first line of defense against antimicrobials in Burkholderia species is the outer membrane penetration barrier. Most Burkholderia contain a modified lipopolysaccharide that causes intrinsic polymyxin resistance. Contributing to reduced drug penetration are restrictive porin proteins. Efflux pumps of the resistance nodulation cell division family are major players in Burkholderia multidrug resistance. Third and fourth generation β-lactam antibiotics are seminal for treatment of Burkholderia infections, but therapeutic efficacy is compromised by expression of several β-lactamases and ceftazidime target mutations. Altered DNA gyrase and dihydrofolate reductase targets cause fluoroquinolone and trimethoprim resistance, respectively. Although antibiotic resistance hampers therapy of Burkholderia infections, the characterization of resistance mechanisms lags behind other non-enteric Gram-negative pathogens, especially ESKAPE bacteria such as Acinetobacter baumannii, Klebsiella pneumoniae and Pseudomonas aeruginosa. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Efflux-mediated antimicrobial resistance.

    Science.gov (United States)

    Poole, Keith

    2005-07-01

    Antibiotic resistance continues to plague antimicrobial chemotherapy of infectious disease. And while true biocide resistance is as yet unrealized, in vitro and in vivo episodes of reduced biocide susceptibility are common and the history of antibiotic resistance should not be ignored in the development and use of biocidal agents. Efflux mechanisms of resistance, both drug specific and multidrug, are important determinants of intrinsic and/or acquired resistance to these antimicrobials, with some accommodating both antibiotics and biocides. This latter raises the spectre (as yet generally unrealized) of biocide selection of multiple antibiotic-resistant organisms. Multidrug efflux mechanisms are broadly conserved in bacteria, are almost invariably chromosome-encoded and their expression in many instances results from mutations in regulatory genes. In contrast, drug-specific efflux mechanisms are generally encoded by plasmids and/or other mobile genetic elements (transposons, integrons) that carry additional resistance genes, and so their ready acquisition is compounded by their association with multidrug resistance. While there is some support for the latter efflux systems arising from efflux determinants of self-protection in antibiotic-producing Streptomyces spp. and, thus, intended as drug exporters, increasingly, chromosomal multidrug efflux determinants, at least in Gram-negative bacteria, appear not to be intended as drug exporters but as exporters with, perhaps, a variety of other roles in bacterial cells. Still, given the clinical significance of multidrug (and drug-specific) exporters, efflux must be considered in formulating strategies/approaches to treating drug-resistant infections, both in the development of new agents, for example, less impacted by efflux and in targeting efflux directly with efflux inhibitors.

  17. Determining the Resistivity of Resistive Sheets Using Transmission Measurements

    National Research Council Canada - National Science Library

    Hyde, IV, Milo W

    2006-01-01

    In September 2005, radar cross section (RCS) measurements were made of resistive sheets, or R-cards, wrapped around a polystyrene foam cylinder to compare with a newly developed theoretical RCS prediction technique...

  18. Multidrug resistant to extensively drug resistant tuberculosis: What is ...

    Indian Academy of Sciences (India)

    Prakash

    The modern, ... World Health Organization is based on a four-drug regimen ... Better management and control of tuberculosis specially drug resistant TB by experienced and qualified .... a comprehensive approach including the major DOTS.

  19. Evolution of methicillin-resistant Staphylococcus aureus towards increasing resistance

    DEFF Research Database (Denmark)

    Strommenger, Birgit; Bartels, Mette Damkjær; Kurt, Kevin

    2014-01-01

    To elucidate the evolutionary history of Staphylococcus aureus clonal complex (CC) 8, which encompasses several globally distributed epidemic lineages, including hospital-associated methicillin-resistant S. aureus (MRSA) and the highly prevalent community-associated MRSA clone USA300.......To elucidate the evolutionary history of Staphylococcus aureus clonal complex (CC) 8, which encompasses several globally distributed epidemic lineages, including hospital-associated methicillin-resistant S. aureus (MRSA) and the highly prevalent community-associated MRSA clone USA300....

  20. The Psychic Life of Resistance

    DEFF Research Database (Denmark)

    Barinaga, Ester

    2013-01-01

    to power. This article is a first step to remedy that oversight. Inspired by Butler’s reading of Foucault’s notion of power at work in subjection and resistance, the article uses Goffman to substantiate such an account. Based on a 20-month ethnographic study of a traditional immigrant suburb north...... of Stockholm, Sweden, which is being redeveloped into a high-tech region, it offers empirical insight into the psychic life of resistance. Further, a particular resistance strategy is identified: symbolic dislocations through adherence to a boundary other than the one subjecting the self in the first place....

  1. Azole-Resistant Invasive Aspergillosis

    DEFF Research Database (Denmark)

    Stensvold, Christen Rune; Jørgensen, Lise Nistrup; Arendrup, Maiken Cavling

    2012-01-01

    with point mutation (s) in CYP51A (TR34/L98H and TR46/Y121F/T289A). In the third a single target enzyme alteration (G432S) is found. These resistant “environmental” strains have been detected in many West-European countries as well as in the Asia- Pacifics. Noticeably, these two continents account...... and classes available is impressive compared to the armamentarium in human medicine, azoles will remain the most important group in agriculture due to superior field performance and significant resistance in fungal pathogens to other compounds. Hence, further spread of environmental resistant Aspergillus...

  2. Electrical Resistivity Measurements: a Review

    Science.gov (United States)

    Singh, Yadunath

    World-wide interest on the use of ceramic materials for aerospace and other advanced engineering applications, has led to the need for inspection techniques capable of detecting unusually electrical and thermal anomalies in these compounds. Modern ceramic materials offer many attractive physical, electrical and mechanical properties for a wide and rapidly growing range of industrial applications; moreover specific use may be made of their electrical resistance, chemical resistance, and thermal barrier properties. In this review, we report the development and various techniques for the resistivity measurement of solid kind of samples.

  3. Radiation-resistant plastic insulators

    International Nuclear Information System (INIS)

    Sturm, B.J.; Parkinson, W.W.

    1975-01-01

    A high molecular weight organic composition useful as an electric insulator in radiation fields is provided and comprises normally a solid polymer of an organic compound having a specific resistance greater than 10 19 ohm-cm and containing phenyl groups and 1 to 7.5 weight percent of a high molecular weight organic phosphite. In one embodiment the composition comprises normally solid polystyrene having 7.5 weight percent tris-β-chloroethyl phosphite as an additive; the composition exhibited an increase in the post-irradiation resistivity of over an order of magnitude over the post-irradiation resistivity of pure polystyrene. (Patent Office Record)

  4. Deciphering MCR-2 Colistin Resistance.

    Science.gov (United States)

    Sun, Jian; Xu, Yongchang; Gao, Rongsui; Lin, Jingxia; Wei, Wenhui; Srinivas, Swaminath; Li, Defeng; Yang, Run-Shi; Li, Xing-Ping; Liao, Xiao-Ping; Liu, Ya-Hong; Feng, Youjun

    2017-05-09

    Antibiotic resistance is a prevalent problem in public health worldwide. In general, the carbapenem β-lactam antibiotics are considered a final resort against lethal infections by multidrug-resistant bacteria. Colistin is a cationic polypeptide antibiotic and acts as the last line of defense for treatment of carbapenem-resistant bacteria. Very recently, a new plasmid-borne colistin resistance gene, mcr-2 , was revealed soon after the discovery of the paradigm gene mcr-1 , which has disseminated globally. However, the molecular mechanisms for MCR-2 colistin resistance are poorly understood. Here we show a unique transposon unit that facilitates the acquisition and transfer of mcr-2 Evolutionary analyses suggested that both MCR-2 and MCR-1 might be traced to their cousin phosphoethanolamine (PEA) lipid A transferase from a known polymyxin producer, Paenibacillus Transcriptional analyses showed that the level of mcr-2 transcripts is relatively higher than that of mcr-1 Genetic deletions revealed that the transmembrane regions (TM1 and TM2) of both MCR-1 and MCR-2 are critical for their location and function in bacterial periplasm, and domain swapping indicated that the TM2 is more efficient than TM1. Matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) confirmed that all four MCR proteins (MCR-1, MCR-2, and two chimeric versions [TM1-MCR-2 and TM2-MCR-1]) can catalyze chemical modification of lipid A moiety anchored on lipopolysaccharide (LPS) with the addition of phosphoethanolamine to the phosphate group at the 4' position of the sugar. Structure-guided site-directed mutagenesis defined an essential 6-residue-requiring zinc-binding/catalytic motif for MCR-2 colistin resistance. The results further our mechanistic understanding of transferable colistin resistance, providing clues to improve clinical therapeutics targeting severe infections by MCR-2-containing pathogens. IMPORTANCE Carbapenem and colistin are the last line of

  5. Fire Resistant, Moisture Barrier Membrane

    Science.gov (United States)

    St.Clair, Terry L. (Inventor)

    2000-01-01

    A waterproof and breathable, fire-resistant laminate is provided for use in tents, garments, shoes, and covers, especially in industrial, military and emergency situations. The laminate permits water vapor evaporation while simultaneously preventing liquid water penetration. Further, the laminate is fire-resistant and significantly reduces the danger of toxic compound production when exposed to flame or other high heat source. The laminate may be applied to a variety of substrates and is comprised of a silicone rubber and plurality of fire-resistant, inherently thermally-stable polyimide particles.

  6. Radiation resistance of Rhizopus stolonifer

    International Nuclear Information System (INIS)

    Robbertse, P.J.; Du Toit, T.L.; Van der Merwe, L.J.; Koekemoer, M.L.; Eilers, I.M.I.

    1983-01-01

    A problem encountered with the irradiation of food is that certain micro-organisms are highly resistant to gamma rays. This includes the fungus, Rhizopus stolonifer, associated with most fruits. The Nuclear Development Corporation of South Africa (NUCOR) has found that a combination of radiation and mild heat treatment reduces the radiation dose necessary to kill 90% of R. stolonifer by approximately half. Treatment at 50 degrees Celsius for 10 minutes or at 55 degrees Celsius for five minutes is sufficient. The article discusses the mechanism of radiation resistance in R. stolonifer and the way in which heating affects this resistance

  7. The evolutionary benefit of insulin resistance

    NARCIS (Netherlands)

    Soeters, Maarten R.; Soeters, Peter B.

    2012-01-01

    Insulin resistance is perceived as deleterious, associated with conditions as the metabolic syndrome, type 2 diabetes mellitus and critical illness. However, insulin resistance is evolutionarily well preserved and its persistence suggests that it benefits survival. Insulin resistance is important in

  8. Systemic resistance induced by rhizosphere bacteria

    NARCIS (Netherlands)

    Loon, L.C. van; Bakker, P.A.H.M.; Pieterse, C.M.J.

    1998-01-01

    Nonpathogenic rhizobacteria can induce a systemic resistance in plants that is phenotypically similar to pathogen-induced systemic acquired resistance (SAR). Rhizobacteria-mediated induced systemic resistance (ISR) has been demonstrated against fungi, bacteria, and viruses in Arabidopsis, bean,

  9. Antibiotic and Antimicrobial Resistance: Threat Report 2013

    Science.gov (United States)

    ... Form Controls Cancel Submit Search The CDC Antibiotic / Antimicrobial Resistance Note: Javascript is disabled or is not ... please visit this page: About CDC.gov . Antibiotic / Antimicrobial Resistance About Antimicrobial Resistance Biggest Threats Emerging Drug ...

  10. Resistant and Refractory Hypertension: Antihypertensive Treatment Resistance vs Treatment Failure

    Science.gov (United States)

    Siddiqui, Mohammed; Dudenbostel, Tanja; Calhoun, David A.

    2017-01-01

    Resistant or difficult to treat hypertension is defined as high blood pressure that remains uncontrolled with 3 or more different antihypertensive medications, including a diuretic. Recent definitions also include controlled blood pressure with use of 4 or more medications as also being resistant to treatment. Recently, refractory hypertension, an extreme phenotype of antihypertensive treatment failure has been defined as hypertension uncontrolled with use of 5 or more antihypertensive agents, including a long-acting thiazide diuretic and a mineralocorticoid receptor antagonist. Patients with resistant vs refractory hypertension share similar characteristics and comorbidities, including obesity, African American race, female sex, diabetes, coronary heart disease, chronic kidney disease, and obstructive sleep apnea. Patients with refractory vs resistant hypertension tend to be younger and are more likely to have been diagnosed with congestive heart failure. Refractory hypertension might also differ from resistant hypertension in terms of underlying cause. Preliminary evidence suggests that refractory hypertension is more likely to be neurogenic in etiology (ie, heightened sympathetic tone), vs a volume-dependent hypertension that is more characteristic of resistant hypertension in general. PMID:26514749

  11. Understanding The Resistance to Health Information Systems

    OpenAIRE

    David Ackah; Angelito E Alvarado; Heru Santoso Wahito Nugroho; Sanglar Polnok; Wiwin Martiningsih

    2017-01-01

    User resistance is users’ opposition to system implementation. Resistance often occurs as a result of a mismatch between management goals and employee preferences. There are two types of resistance to health iformation system namely active resistance and passive resistance. The manifestation of active resistance are being critical,  blaming/accusing, blocking, fault finding, sabotaging, undermining, ridiculing, intimidating/threatening, starting rumors, appealing to fear, manipulating arguing...

  12. Communication equipment radiation resistance ensurance

    International Nuclear Information System (INIS)

    Myrova, L.O.; Chelizhenko, A.Z.

    1983-01-01

    A review of works on radiation resistance of electronic equipment (epsilon epsilon) for 15 years is presented. The effect of ionizing radiation appearing as a result of nuclear explosions in nuclear facilities and in outerspace on epsilon epsilon has been considered. Types of radiation effects in epsilon epsilon, radiation effect on semiconductor devices and integrated circUits, types of epsilon epsilon failures, as well as the procass of radiation-resistant epsilon epsilon designing and selection of its main parameters have been described. The methods of epsilon epsilon flowsheet optimization, application of mathematical simulation and peculiarities of ensurance of epsilon epsilon radiation resistance of communication systems are considered. Peculiarities of designing of radiation-resistant quartz generators, secondary power supply sources and amplifiers are discussed

  13. Thermomechanical Modelling of Resistance Welding

    DEFF Research Database (Denmark)

    Bay, Niels; Zhang, Wenqi

    2007-01-01

    The present paper describes a generic programme for analysis, optimization and development of resistance spot and projection welding. The programme includes an electrical model determining electric current and voltage distribution as well as heat generation, a thermal model calculating heat...

  14. Erosion-resistant composite material

    Science.gov (United States)

    Finch, C.B.; Tennery, V.J.; Curlee, R.M.

    A highly erosion-resistant composite material is formed of chemical vapor-deposited titanium diboride on a sintered titanium diboride-nickel substrate. This material may be suitable for use in cutting tools, coal liquefaction systems, etc.

  15. Stronger Fire-Resistant Epoxies

    Science.gov (United States)

    Fohlen, George M.; Parker, John A.; Kumar, Devendra

    1988-01-01

    New curing agent improves mechanical properties and works at lower temperature. Use of aminophenoxycyclotriphosphazene curing agents yields stronger, more heat- and fire-resistant epoxy resins. Used with solvent if necessary for coating fabrics or casting films.

  16. Antimicrobial resistance in the environment

    National Research Council Canada - National Science Library

    Keen, Patricia L; Montforts, M. H. M. M

    2012-01-01

    ... or antibiotic resistance genes as environmental contaminants. It also considers alternate uses and functions for antimicrobial compounds other than those intended for medicinal purposes in humans, animals, and fish...

  17. Strategies to Minimize Antibiotic Resistance

    Directory of Open Access Journals (Sweden)

    Sang Hee Lee

    2013-09-01

    Full Text Available Antibiotic resistance can be reduced by using antibiotics prudently based on guidelines of antimicrobial stewardship programs (ASPs and various data such as pharmacokinetic (PK and pharmacodynamic (PD properties of antibiotics, diagnostic testing, antimicrobial susceptibility testing (AST, clinical response, and effects on the microbiota, as well as by new antibiotic developments. The controlled use of antibiotics in food animals is another cornerstone among efforts to reduce antibiotic resistance. All major resistance-control strategies recommend education for patients, children (e.g., through schools and day care, the public, and relevant healthcare professionals (e.g., primary-care physicians, pharmacists, and medical students regarding unique features of bacterial infections and antibiotics, prudent antibiotic prescribing as a positive construct, and personal hygiene (e.g., handwashing. The problem of antibiotic resistance can be minimized only by concerted efforts of all members of society for ensuring the continued efficiency of antibiotics.

  18. Mechanisms of Resistance to Neurotoxins

    National Research Council Canada - National Science Library

    Schubert, David

    2002-01-01

    .... During all of these events, some groups of nerve cells are spared relative to others. It is therefore likely that biochemical mechanisms exist which lead to increased resistance to oxidative stress and other forms of cytotoxicity...

  19. Bacterial cheating limits antibiotic resistance

    Science.gov (United States)

    Xiao Chao, Hui; Yurtsev, Eugene; Datta, Manoshi; Artemova, Tanya; Gore, Jeff

    2012-02-01

    The widespread use of antibiotics has led to the evolution of resistance in bacteria. Bacteria can gain resistance to the antibiotic ampicillin by acquiring a plasmid carrying the gene beta-lactamase, which inactivates the antibiotic. This inactivation may represent a cooperative behavior, as the entire bacterial population benefits from removing the antibiotic. The cooperative nature of this growth suggests that a cheater strain---which does not contribute to breaking down the antibiotic---may be able to take advantage of cells cooperatively inactivating the antibiotic. Here we find experimentally that a ``sensitive'' bacterial strain lacking the plasmid conferring resistance can invade a population of resistant bacteria, even in antibiotic concentrations that should kill the sensitive strain. We observe stable coexistence between the two strains and find that a simple model successfully explains the behavior as a function of antibiotic concentration and cell density. We anticipate that our results will provide insight into the evolutionary origin of phenotypic diversity and cooperative behaviors.

  20. "Feeling" Series and Parallel Resistances.

    Science.gov (United States)

    Morse, Robert A.

    1993-01-01

    Equipped with drinking straws and stirring straws, a teacher can help students understand how resistances in electric circuits combine in series and in parallel. Follow-up suggestions are provided. (ZWH)

  1. Employee Resistance to Computer Technology.

    Science.gov (United States)

    Ewert, Alan

    1984-01-01

    The introduction of computers to the work place may cause employee stress. Aggressive, protective, and avoidance behaviors are forms of staff resistance. The development of good training programs will enhance productivity. Suggestions for evaluating computer systems are offered. (DF)

  2. New principle of chemotherapy resistance

    Science.gov (United States)

    A laboratory study has revealed an entirely unexpected process for acquiring drug resistance that bypasses the need to re-establish DNA damage repair in breast cancers that have mutant BRCA1 or BRCA2 genes.

  3. Heavy resistance training and lymphedema

    DEFF Research Database (Denmark)

    Bloomquist, Kira; Karlsmark, Tonny; Christensen, Karl Bang

    2014-01-01

    BACKGROUND: There is limited knowledge regarding progressive resistance training during adjuvant chemotherapy and the risk of developing breast cancer-related lymphedema (BCRL). Furthermore, no studies have investigated the safety of resistance training with heavy loads (> 80% 1 repetition maximum......) in this population. 'Body and Cancer' is a six-week, nine-hour weekly, supervised, multimodal exercise intervention utilizing progressive resistance training with heavy loads for cancer patients undergoing chemotherapy. The purpose of the present study was to estimate the prevalence of BCRL in former participants......, and identify associations between progressive resistance training with heavy loads, and the development of BCRL. MATERIAL AND METHODS: This was a descriptive study. POPULATION: Women treated for breast cancer (n = 149), who had participated in the 'Body and Cancer' exercise intervention between 1 January 2010...

  4. Intrinsic nanofilamentation in resistive switching

    KAUST Repository

    Wu, Xing; Cha, Dong Kyu; Bosman, Michel; Raghavan, Nagarajan; Migas, Dmitri B.; Borisenko, Victor E.; Zhang, Xixiang; Li, Kun; Pey, Kin-Leong

    2013-01-01

    -chip circuitry and non-volatile memory storage. Here, we provide insight into the mechanisms that govern highly reproducible controlled resistive switching via a nanofilament by using an asymmetric metal-insulator-semiconductor structure. In-situ transmission

  5. Insulin resistance and chronic inflammation

    Directory of Open Access Journals (Sweden)

    Natalia Matulewicz

    2016-12-01

    Full Text Available Insulin resistance is a condition of reduced biological response to insulin. Growing evidence indicates the role of the chronic low-grade inflammatory response in the pathogenesis of insulin resistance. Adipose tissue in obesity is characterized by increased lipolysis with the excessive release of free fatty acids, and is also a source of proinflammatory cytokines. Both these factors may inhibit insulin action. Proinflammatory cytokines exert their effect by stimulating major inflammatory NFκB and JNK pathways within the cells. Inflammatory processes in other insulin responsive tissues may also play a role in inducing insulin resistance. This paper is an overview of the chronic low-grade inflammation in adipose tissue, skeletal muscle, liver and endothelial cells during the development of insulin resistance.

  6. Radiation-resistant asporogenic bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Yano, K [Tokyo Univ. (Japan). Faculty of Agriculture

    1975-09-01

    This paper reports the biological and ecological examinations on the radiation-resistant asporogenic bacteria (mainly concerning Micrococcus radiodurans). Radiation-resistant asporogenic bacteria were isolated from the irradiated areas of the natural world as well as from the general areas and from the Rn waters in the Misasa hot spring. The acquiring of the tolerance to radiation in bacteria was also examined. In addition, the future problems of microbiological treatment with irradiation were mentioned.

  7. Radiation-resistant asporogenic bacteria

    International Nuclear Information System (INIS)

    Yano, Keiji

    1975-01-01

    This paper reports the biological and ecological examinations on the radiation-resistant asporogenic bacteria (mainly concerning Micrococcus radiodurans). Radiation-resistant asporogenic bacteria were isolated from the irradiated areas of the natural world as well as from the general areas and from the Rn waters in the Misasa hot spring. The acquiring of the tolerance to radiation in bacteria was also examined. In addition, the future problems of microbiological treatment with irradiation were mentioned. (Tsukamoto, Y.)

  8. Slave songs: Codes of resistance

    OpenAIRE

    Bayer, Sidney Konrad

    2010-01-01

    When slaves were forcibly taken from their homes in Africa and brought to North America to live, work, and die in servitude, they brought with them their culture. This included music and dance, which had been used for generations to express their feelings. Africans still use songs to criticize, to protest, for social commentary, and to resist oppression. Slaves used a variety of means to protest and resist their condition; for example, secret meetings, songs which encouraged escape and sabota...

  9. Trimaran Resistance Artificial Neural Network

    Science.gov (United States)

    2011-01-01

    11th International Conference on Fast Sea Transportation FAST 2011, Honolulu, Hawaii, USA, September 2011 Trimaran Resistance Artificial Neural Network Richard...Trimaran Resistance Artificial Neural Network 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e... Artificial Neural Network and is restricted to the center and side-hull configurations tested. The value in the parametric model is that it is able to

  10. Corrosion resistant neutron absorbing coatings

    Science.gov (United States)

    Choi, Jor-Shan [El Cerrito, CA; Farmer, Joseph C [Tracy, CA; Lee, Chuck K [Hayward, CA; Walker, Jeffrey [Gaithersburg, MD; Russell, Paige [Las Vegas, NV; Kirkwood, Jon [Saint Leonard, MD; Yang, Nancy [Lafayette, CA; Champagne, Victor [Oxford, PA

    2012-05-29

    A method of forming a corrosion resistant neutron absorbing coating comprising the steps of spray or deposition or sputtering or welding processing to form a composite material made of a spray or deposition or sputtering or welding material, and a neutron absorbing material. Also a corrosion resistant neutron absorbing coating comprising a composite material made of a spray or deposition or sputtering or welding material, and a neutron absorbing material.

  11. Antimicrobial resistance mechanisms among Campylobacter.

    Science.gov (United States)

    Wieczorek, Kinga; Osek, Jacek

    2013-01-01

    Campylobacter jejuni and Campylobacter coli are recognized as the most common causative agents of bacterial gastroenteritis in the world. Humans most often become infected by ingesting contaminated food, especially undercooked chicken, but also other sources of bacteria have been described. Campylobacteriosis is normally a self-limiting disease. Antimicrobial treatment is needed only in patients with more severe disease and in those who are immunologically compromised. The most common antimicrobial agents used in the treatment of Campylobacter infections are macrolides, such as erythromycin, and fluoroquinolones, such as ciprofloxacin. Tetracyclines have been suggested as an alternative choice in the treatment of clinical campylobacteriosis but in practice are not often used. However, during the past few decades an increasing number of resistant Campylobacter isolates have developed resistance to fluoroquinolones and other antimicrobials such as macrolides, aminoglycosides, and beta-lactams. Trends in antimicrobial resistance have shown a clear correlation between use of antibiotics in the veterinary medicine and animal production and resistant isolates of Campylobacter in humans. In this review, the patterns of emerging resistance to the antimicrobial agents useful in treatment of the disease are presented and the mechanisms of resistance to these drugs in Campylobacter are discussed.

  12. Resistant starch in cassava products

    Directory of Open Access Journals (Sweden)

    Bruna Letícia Buzati Pereira

    2014-06-01

    Full Text Available Found in different foods, starch is the most important source of carbohydrates in the diet. Some factors present in starchy foods influence the rate at which the starch is hydrolyzed and absorbed in vivo. Due the importance of cassava products in Brazilian diet, the objective of this study was to analyze total starch, resistant starch, and digestible starch contents in commercial cassava products. Thirty three commercial cassava products from different brands, classifications, and origin were analyzed. The method used for determination of resistant starch consisted of an enzymatic process to calculate the final content of resistant starch considering the concentration of glucose released and analyzed. The results showed significant differences between the products. Among the flours and seasoned flours analyzed, the highest levels of resistant starch were observed in the flour from Bahia state (2.21% and the seasoned flour from Paraná state (1.93%. Starch, tapioca, and sago showed levels of resistant starch ranging from 0.56 to 1.1%. The cassava products analyzed can be considered good sources of resistant starch; which make them beneficial products to the gastrointestinal tract.

  13. Candida Species Biofilms’ Antifungal Resistance

    Science.gov (United States)

    Silva, Sónia; Rodrigues, Célia F.; Araújo, Daniela; Rodrigues, Maria Elisa; Henriques, Mariana

    2017-01-01

    Candida infections (candidiasis) are the most prevalent opportunistic fungal infection on humans and, as such, a major public health problem. In recent decades, candidiasis has been associated to Candida species other than Candida albicans. Moreover, biofilms have been considered the most prevalent growth form of Candida cells and a strong causative agent of the intensification of antifungal resistance. As yet, no specific resistance factor has been identified as the sole responsible for the increased recalcitrance to antifungal agents exhibited by biofilms. Instead, biofilm antifungal resistance is a complex multifactorial phenomenon, which still remains to be fully elucidated and understood. The different mechanisms, which may be responsible for the intrinsic resistance of Candida species biofilms, include the high density of cells within the biofilm, the growth and nutrient limitation, the effects of the biofilm matrix, the presence of persister cells, the antifungal resistance gene expression and the increase of sterols on the membrane of biofilm cells. Thus, this review intends to provide information on the recent advances about Candida species biofilm antifungal resistance and its implication on intensification of the candidiasis. PMID:29371527

  14. Atomic crystals resistive switching memory

    International Nuclear Information System (INIS)

    Liu Chunsen; Zhang David Wei; Zhou Peng

    2017-01-01

    Facing the growing data storage and computing demands, a high accessing speed memory with low power and non-volatile character is urgently needed. Resistive access random memory with 4F 2 cell size, switching in sub-nanosecond, cycling endurances of over 10 12 cycles, and information retention exceeding 10 years, is considered as promising next-generation non-volatile memory. However, the energy per bit is still too high to compete against static random access memory and dynamic random access memory. The sneak leakage path and metal film sheet resistance issues hinder the further scaling down. The variation of resistance between different devices and even various cycles in the same device, hold resistive access random memory back from commercialization. The emerging of atomic crystals, possessing fine interface without dangling bonds in low dimension, can provide atomic level solutions for the obsessional issues. Moreover, the unique properties of atomic crystals also enable new type resistive switching memories, which provide a brand-new direction for the resistive access random memory. (topical reviews)

  15. Review of resistance factor for steel: resistance distributions and resistance factor calibration

    International Nuclear Information System (INIS)

    Schmidt, B.J.; Bartlett, F.M.

    2002-01-01

    Changes in the Canadian steel industry warrant a review of the steel resistance factor in CSA Standard S16 (formerly S16.1) 'Limit states design of steel structures', originally calibrated in the landmark study by Kennedy and Gad Aly in 1980. This paper presents statistical parameters for the bending, compression, and tension resistances of W, WWF, and HSS components produced since 1999 that have been derived from geometric and material properties presented in a companion paper. The resistance factor for steel was recalibrated for the live and dead load combination in the 1995 National Building Code of Canada. A resistance factor of 0.95 is suitable for laterally supported beams, stocky columns, and tension members failing by yield of the gross section, whereas the current value of 0.90 is appropriate for intermediate columns and tension members failing by fracture of the net section. (author)

  16. Insulin resistance: definition and consequences.

    Science.gov (United States)

    Lebovitz, H E

    2001-01-01

    Insulin resistance is defined clinically as the inability of a known quantity of exogenous or endogenous insulin to increase glucose uptake and utilization in an individual as much as it does in a normal population. Insulin action is the consequence of insulin binding to its plasma membrane receptor and is transmitted through the cell by a series of protein-protein interactions. Two major cascades of protein-protein interactions mediate intracellular insulin action: one pathway is involved in regulating intermediary metabolism and the other plays a role in controlling growth processes and mitoses. The regulation of these two distinct pathways can be dissociated. Indeed, some data suggest that the pathway regulating intermediary metabolism is diminished in type 2 diabetes while that regulating growth processes and mitoses is normal.--Several mechanisms have been proposed as possible causes underlying the development of insulin resistance and the insulin resistance syndrome. These include: (1) genetic abnormalities of one or more proteins of the insulin action cascade (2) fetal malnutrition (3) increases in visceral adiposity. Insulin resistance occurs as part of a cluster of cardiovascular-metabolic abnormalities commonly referred to as "The Insulin Resistance Syndrome" or "The Metabolic Syndrome". This cluster of abnormalities may lead to the development of type 2 diabetes, accelerated atherosclerosis, hypertension or polycystic ovarian syndrome depending on the genetic background of the individual developing the insulin resistance.--In this context, we need to consider whether insulin resistance should be defined as a disease entity which needs to be diagnosed and treated with specific drugs to improve insulin action.

  17. Deciphering MCR-2 Colistin Resistance

    Directory of Open Access Journals (Sweden)

    Jian Sun

    2017-05-01

    Full Text Available Antibiotic resistance is a prevalent problem in public health worldwide. In general, the carbapenem β-lactam antibiotics are considered a final resort against lethal infections by multidrug-resistant bacteria. Colistin is a cationic polypeptide antibiotic and acts as the last line of defense for treatment of carbapenem-resistant bacteria. Very recently, a new plasmid-borne colistin resistance gene, mcr-2, was revealed soon after the discovery of the paradigm gene mcr-1, which has disseminated globally. However, the molecular mechanisms for MCR-2 colistin resistance are poorly understood. Here we show a unique transposon unit that facilitates the acquisition and transfer of mcr-2. Evolutionary analyses suggested that both MCR-2 and MCR-1 might be traced to their cousin phosphoethanolamine (PEA lipid A transferase from a known polymyxin producer, Paenibacillus. Transcriptional analyses showed that the level of mcr-2 transcripts is relatively higher than that of mcr-1. Genetic deletions revealed that the transmembrane regions (TM1 and TM2 of both MCR-1 and MCR-2 are critical for their location and function in bacterial periplasm, and domain swapping indicated that the TM2 is more efficient than TM1. Matrix-assisted laser desorption ionization–time of flight mass spectrometry (MALDI-TOF MS confirmed that all four MCR proteins (MCR-1, MCR-2, and two chimeric versions [TM1-MCR-2 and TM2-MCR-1] can catalyze chemical modification of lipid A moiety anchored on lipopolysaccharide (LPS with the addition of phosphoethanolamine to the phosphate group at the 4′ position of the sugar. Structure-guided site-directed mutagenesis defined an essential 6-residue-requiring zinc-binding/catalytic motif for MCR-2 colistin resistance. The results further our mechanistic understanding of transferable colistin resistance, providing clues to improve clinical therapeutics targeting severe infections by MCR-2-containing pathogens.

  18. Rolling Resistance Measurement and Model Development

    DEFF Research Database (Denmark)

    Andersen, Lasse Grinderslev; Larsen, Jesper; Fraser, Elsje Sophia

    2015-01-01

    There is an increased focus worldwide on understanding and modeling rolling resistance because reducing the rolling resistance by just a few percent will lead to substantial energy savings. This paper reviews the state of the art of rolling resistance research, focusing on measuring techniques, s......, surface and texture modeling, contact models, tire models, and macro-modeling of rolling resistance...

  19. Analytic study of resistive instabilities

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Magnus

    2003-05-01

    In a fusion plasma there is always a small amount of resistivity that may cause instabilities. Although their rather slow growth rates they can be of major importance for fusion plasma confinement. In this work a MAPLE-code was rewritten and simplified to make it possible to analytically solve the linearized MHD-equations with resistivity in an RFP-configuration. By using the MHD-equations and expanding the unknown perturbed quantities u{sub 1r}(r) and B{sub 1r}(r) as Taylor series and solving each coefficient we could get eigenvalues, dispersion relations and a relation between the growth rate and the resistivity. The new code was first used to solve two cases with no resistivity and simple unstable equilibria which after running gave the correct expected results. The difference from running the original code with these two cases was the greater speed of the calculations and the less memory needed. Then by using an ideal MHD-stable equilibrium in a plasma with no resistivity the code gave us solutions which unfortunately were not of the expected kind but the time of the calculations was still very fast. The resistivity was finally added to the code with the ideal MHD-stable equilibrium. The program also this time gave incorrect results. We could, however, see from a relation between the growth rate and the resistivity that the solution may be approximately correct in this domain. Although we did not get all the correct results we have to consider the fact that we got results, that were not possible before. Before this work was carried out we could not get any results at all in the resistive cue because of the very long memory demanding expressions. In future work and studies it is not only possible to get the desired eigenvalues {gamma} as function of {eta} but also possible to get expressions for eigenfunctions, dispersion relations and other significant relations with a number of variable parameters. We could also use the method for any geometry and possibly for

  20. Analytic study of resistive instabilities

    International Nuclear Information System (INIS)

    Svensson, Magnus

    2003-05-01

    In a fusion plasma there is always a small amount of resistivity that may cause instabilities. Although their rather slow growth rates they can be of major importance for fusion plasma confinement. In this work a MAPLE-code was rewritten and simplified to make it possible to analytically solve the linearized MHD-equations with resistivity in an RFP-configuration. By using the MHD-equations and expanding the unknown perturbed quantities u 1r (r) and B 1r (r) as Taylor series and solving each coefficient we could get eigenvalues, dispersion relations and a relation between the growth rate and the resistivity. The new code was first used to solve two cases with no resistivity and simple unstable equilibria which after running gave the correct expected results. The difference from running the original code with these two cases was the greater speed of the calculations and the less memory needed. Then by using an ideal MHD-stable equilibrium in a plasma with no resistivity the code gave us solutions which unfortunately were not of the expected kind but the time of the calculations was still very fast. The resistivity was finally added to the code with the ideal MHD-stable equilibrium. The program also this time gave incorrect results. We could, however, see from a relation between the growth rate and the resistivity that the solution may be approximately correct in this domain. Although we did not get all the correct results we have to consider the fact that we got results, that were not possible before. Before this work was carried out we could not get any results at all in the resistive cue because of the very long memory demanding expressions. In future work and studies it is not only possible to get the desired eigenvalues γ as function of η but also possible to get expressions for eigenfunctions, dispersion relations and other significant relations with a number of variable parameters. We could also use the method for any geometry and possibly for non

  1. Insulin Resistance in Alzheimer's Disease

    Science.gov (United States)

    Dineley, Kelly T; Jahrling, Jordan B; Denner, Larry

    2014-01-01

    Insulin is a key hormone regulating metabolism. Insulin binding to cell surface insulin receptors engages many signaling intermediates operating in parallel and in series to control glucose, energy, and lipids while also regulating mitogenesis and development. Perturbations in the function of any of these intermediates, which occur in a variety of diseases, cause reduced sensitivity to insulin and insulin resistance with consequent metabolic dysfunction. Chronic inflammation ensues which exacerbates compromised metabolic homeostasis. Since insulin has a key role in learning and memory as well as directly regulating ERK, a kinase required for the type of learning and memory compromised in early Alzheimer's disease (AD), insulin resistance has been identified as a major risk factor for the onset of AD. Animal models of AD or insulin resistance or both demonstrate that AD pathology and impaired insulin signaling form a reciprocal relationship. Of note are human and animal model studies geared toward improving insulin resistance that have led to the identification of the nuclear receptor and transcription factor, peroxisome proliferator-activated receptor gamma (PPARγ) as an intervention tool for early AD. Strategic targeting of alternate nodes within the insulin signaling network has revealed disease-stage therapeutic windows in animal models that coalesce with previous and ongoing clinical trial approaches. Thus, exploiting the connection between insulin resistance and AD provides powerful opportunities to delineate therapeutic interventions that slow or block the pathogenesis of AD. PMID:25237037

  2. Insulin Resistance and Mitochondrial Dysfunction.

    Science.gov (United States)

    Gonzalez-Franquesa, Alba; Patti, Mary-Elizabeth

    2017-01-01

    Insulin resistance precedes and predicts the onset of type 2 diabetes (T2D) in susceptible humans, underscoring its important role in the complex pathogenesis of this disease. Insulin resistance contributes to multiple tissue defects characteristic of T2D, including reduced insulin-stimulated glucose uptake in insulin-sensitive tissues, increased hepatic glucose production, increased lipolysis in adipose tissue, and altered insulin secretion. Studies of individuals with insulin resistance, both with established T2D and high-risk individuals, have consistently demonstrated a diverse array of defects in mitochondrial function (i.e., bioenergetics, biogenesis and dynamics). However, it remains uncertain whether mitochondrial dysfunction is primary (critical initiating defect) or secondary to the subtle derangements in glucose metabolism, insulin resistance, and defective insulin secretion present early in the course of disease development. In this chapter, we will present the evidence linking mitochondrial dysfunction and insulin resistance, and review the potential for mitochondrial targets as a therapeutic approach for T2D.

  3. Selective Insulin Resistance in Adipocytes*

    Science.gov (United States)

    Tan, Shi-Xiong; Fisher-Wellman, Kelsey H.; Fazakerley, Daniel J.; Ng, Yvonne; Pant, Himani; Li, Jia; Meoli, Christopher C.; Coster, Adelle C. F.; Stöckli, Jacqueline; James, David E.

    2015-01-01

    Aside from glucose metabolism, insulin regulates a variety of pathways in peripheral tissues. Under insulin-resistant conditions, it is well known that insulin-stimulated glucose uptake is impaired, and many studies attribute this to a defect in Akt signaling. Here we make use of several insulin resistance models, including insulin-resistant 3T3-L1 adipocytes and fat explants prepared from high fat-fed C57BL/6J and ob/ob mice, to comprehensively distinguish defective from unaffected aspects of insulin signaling and its downstream consequences in adipocytes. Defective regulation of glucose uptake was observed in all models of insulin resistance, whereas other major actions of insulin such as protein synthesis and anti-lipolysis were normal. This defect corresponded to a reduction in the maximum response to insulin. The pattern of change observed for phosphorylation in the Akt pathway was inconsistent with a simple defect at the level of Akt. The only Akt substrate that showed consistently reduced phosphorylation was the RabGAP AS160 that regulates GLUT4 translocation. We conclude that insulin resistance in adipose tissue is highly selective for glucose metabolism and likely involves a defect in one of the components regulating GLUT4 translocation to the cell surface in response to insulin. PMID:25720492

  4. An innovation resistance factor model

    Directory of Open Access Journals (Sweden)

    Siti Salwa Mohd Ishak

    2016-09-01

    Full Text Available The process and implementation strategy of information technology in construction is generally considered through the limiting prism of theoretical contexts generated from innovation diffusion and acceptance. This research argues that more attention should be given to understanding the positive effects of resistance. The study develops a theoretical framing for the Integrated Resistance Factor Model (IRFM. The framing uses a combination of diffusion of innovation theory, technology acceptance model and social network perspective. The model is tested to identify the most significant resistance factors using Partial Least Square (PLS technique. All constructs proposed in the model are found to be significant, valid and consistent with the theoretical framework. IRFM is shown to be an effective and appropriate model of user resistance factors. The most critical factors to influence technology resistance in the online project information management system (OPIMS context are: support from leaders and peers, complexity of the technology, compatibility with key work practices; and pre-trial of the technology before it is actually deployed. The study provides a new model for further research in technology innovation specific to the construction industry.

  5. Resistant Hypertension and Cardiorenovascular Risk

    Directory of Open Access Journals (Sweden)

    Prkacin Ingrid

    2017-06-01

    Full Text Available Studies have documented independent contribution of sympathetic activation to the cardiovascular disease continuum. Hypertension is one of the leading modifiable factors. Most if not all the benefit of antihypertensive treatment depends on blood pressure lowering, regardless how it is obtained. Resistant hypertension is defined as blood pressure that remains uncontrolled in spite of the concurrent use of three antihypertensive drugs of different classes. Ideally, one of the three drugs should be a diuretic, and all drugs should be prescribed at optimal dose amounts. Poor adherence to antihypertensive therapy, undiscovered secondary causes (e.g. obstructive sleep apnea, primary aldosteronism, renal artery stenosis, and lifestyle factors (e.g. obesity, excessive sodium intake, heavy alcohol intake, various drug interactions are the most common causes of resistant hypertension. Cardio(renovascular morbidity and mortality are significantly higher in resistant hypertensive than in general hypertensive population, as such patients are typically presented with a long-standing history of poorly controlled hypertension. Early diagnosis and treatment is needed to avoid further end-organ damage to prevent cardiorenovascular remodeling. Treatment strategy includes lifestyle changes, adding a mineralocorticoid receptor antagonist, treatment adherence in cardiovascular prevention and, in case of failure to control blood pressure, renal sympathetic denervation or baroreceptor activation therapy. The comparative outcomes in resistant hypertension deserve better understanding. In this review, the most current approaches to resistant hypertension and cardiovascular risk based on the available literature evidence will be discussed.

  6. Drug-resistant spinal tuberculosis

    Directory of Open Access Journals (Sweden)

    Anil K Jain

    2018-01-01

    Full Text Available Drug-resistant spinal tuberculosis (TB is an emerging health problem in both developing and developed countries. In this review article, we aim to define management protocols for suspicion, diagnosis, and treatment of such patients. Spinal TB is a deep-seated paucibacillary lesion, and the demonstration of acid-fast bacilli on Ziehl-Neelsen staining is possible only in 10%–30% of cases. Drug resistance is suspected in patients showing the failure of clinicoradiological improvement or appearance of a fresh lesion of osteoarticular TB while on anti tubercular therapy (ATT for a minimum period of 5 months. The conventional culture of Mycobacterium tuberculosis remains the gold standard for both bacteriological diagnosis and drug sensitivity testing (DST; however, the high turn around time of 2–6 weeks for detection with added 3 weeks for DST is a major limitation. To overcome this problem, rapid culture methods and molecular methods have been introduced. From a public health perspective, reducing the period between diagnosis and treatment initiation has direct benefits for both the patient and the community. For all patients of drug-resistant spinal TB, a complete Drug-O-Gram should be prepared which includes details of all drugs, their doses, and duration. Patients with confirmed multidrug-resistant TB strains should receive a regimen with at least five effective drugs, including pyrazinamide and one injectable. Patients with resistance to additional antitubercular drugs should receive individualized ATT as per their DST results.

  7. Insecticide resistance and intracellular proteases.

    Science.gov (United States)

    Wilkins, Richard M

    2017-12-01

    Pesticide resistance is an example of evolution in action with mechanisms of resistance arising from mutations or increased expression of intrinsic genes. Intracellular proteases have a key role in maintaining healthy cells and in responding to stressors such as pesticides. Insecticide-resistant insects have constitutively elevated intracellular protease activity compared to corresponding susceptible strains. This increase was shown for some cases originally through biochemical enzyme studies and subsequently putatively by transcriptomics and proteomics methods. Upregulation and expression of proteases have been characterised in resistant strains of some insect species, including mosquitoes. This increase in proteolysis results in more degradation products (amino acids) of intracellular proteins. These may be utilised in the resistant strain to better protect the cell from stress. There are changes in insect intracellular proteases shortly after insecticide exposure, suggesting a role in stress response. The use of protease and proteasome inhibitors or peptide mimetics as synergists with improved application techniques and through protease gene knockdown using RNA interference (possibly expressed in crop plants) may be potential pest management strategies, in situations where elevated intracellular proteases are relevant. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  8. Resistance exercise training for fibromyalgia.

    Science.gov (United States)

    Busch, Angela J; Webber, Sandra C; Richards, Rachel S; Bidonde, Julia; Schachter, Candice L; Schafer, Laurel A; Danyliw, Adrienne; Sawant, Anuradha; Dal Bello-Haas, Vanina; Rader, Tamara; Overend, Tom J

    2013-12-20

    Fibromyalgia is characterized by chronic widespread pain that leads to reduced physical function. Exercise training is commonly recommended as a treatment for management of symptoms. We examined the literature on resistance training for individuals with fibromyalgia. Resistance training is exercise performed against a progressive resistance with the intention of improving muscle strength, muscle endurance, muscle power, or a combination of these. To evaluate the benefits and harms of resistance exercise training in adults with fibromyalgia. We compared resistance training versus control and versus other types of exercise training. We searched nine electronic databases (The Cochrane Library, MEDLINE, EMBASE, CINAHL, PEDro, Dissertation Abstracts, Current Controlled Trials, World Health Organization (WHO) International Clinical Trials Registry Platform, AMED) and other sources for published full-text articles. The date of the last search was 5 March 2013. Two review authors independently screened 1856 citations, 766 abstracts and 156 full-text articles. We included five studies that met our inclusion criteria. Selection criteria included: a) randomized clinical trial, b) diagnosis of fibromyalgia based on published criteria, c) adult sample, d) full-text publication, and e) inclusion of between-group data comparing resistance training versus a control or other physical activity intervention. Pairs of review authors independently assessed risk of bias and extracted intervention and outcome data. We resolved disagreements between the two review authors and questions regarding interpretation of study methods by discussion within the pairs or when necessary the issue was taken to the full team of 11 members. We extracted 21 outcomes of which seven were designated as major outcomes: multidimensional function, self reported physical function, pain, tenderness, muscle strength, attrition rates, and adverse effects. We evaluated benefits and harms of the interventions using

  9. Paediatrics, insulin resistance and the kidney.

    Science.gov (United States)

    Marlais, Matko; Coward, Richard J

    2015-08-01

    Systemic insulin resistance is becoming more prevalent in the young due to modern lifestyles predisposing to the metabolic syndrome and obesity. There is also evidence that there are critical insulin-resistant phases for the developing child, including puberty, and that renal disease per se causes systemic insulin resistance. This review considers the factors that render children insulin resistant, as well as the accumulating evidence that the kidney is an insulin-responsive organ and could be affected by insulin resistance.

  10. Photolithography-free laser-patterned HF acid-resistant chromium-polyimide mask for rapid fabrication of microfluidic systems in glass

    International Nuclear Information System (INIS)

    Zamuruyev, Konstantin O; Zrodnikov, Yuriy; Davis, Cristina E

    2017-01-01

    Excellent chemical and physical properties of glass, over a range of operating conditions, make it a preferred material for chemical detection systems in analytical chemistry, biology, and the environmental sciences. However, it is often compromised with SU8, PDMS, or Parylene materials due to the sophisticated mask preparation requirements for wet etching of glass. Here, we report our efforts toward developing a photolithography-free laser-patterned hydrofluoric acid-resistant chromium-polyimide tape mask for rapid prototyping of microfluidic systems in glass. The patterns are defined in masking layer with a diode-pumped solid-state laser. Minimum feature size is limited to the diameter of the laser beam, 30 µ m; minimum spacing between features is limited by the thermal shrinkage and adhesive contact of the polyimide tape to 40 µ m. The patterned glass substrates are etched in 49% hydrofluoric acid at ambient temperature with soft agitation (in time increments, up to 60 min duration). In spite of the simplicity, our method demonstrates comparable results to the other current more sophisticated masking methods in terms of the etched depth (up to 300 µ m in borosilicate glass), feature under etch ratio in isotropic etch (∼1.36), and low mask hole density. The method demonstrates high yield and reliability. To our knowledge, this method is the first proposed technique for rapid prototyping of microfluidic systems in glass with such high performance parameters. The proposed method of fabrication can potentially be implemented in research institutions without access to a standard clean-room facility. (paper)

  11. Resistance to minor groove binders.

    Science.gov (United States)

    Colmegna, Benedetta; Uboldi, Sarah; Erba, Eugenio; D'Incalci, Maurizio

    2014-03-01

    In this paper multiple resistance mechanisms to minor groove binders (MGBs) are overviewed. MGBs with antitumor properties are natural products or their derivatives and, as expected, they are all substrates of P-glycoprotein (P-gp). However, a moderate expression of P-gp does not appear to reduce the sensitivity to trabectedin, the only MGB so far approved for clinical use. Resistance to this drug is often related to transcriptional mechanisms and to DNA repair pathways, particularly defects in transcription-coupled nucleotide excision repair (TC-NER). Therefore tumors resistant to trabectedin may become hypersensitive to UV rays and other DNA damaging agents acting in the major groove, such as Platinum (Pt) complexes. If this is confirmed in clinic, that will provide the rationale to combine trabectedin sequentially with Pt derivates.

  12. Liquefaction resistance of calcareous sands

    International Nuclear Information System (INIS)

    Sandoval Vallejo, Eimar

    2012-01-01

    Calcareous sands are unique in terms of their origin, mineralogy, shape, fragility and intra particle porosity. This article presents results from an experimental program carried out to study the liquefaction resistance of a calcareous sand retrieved from Cabo Rojo at Puerto Rico. The experimental program included mineralogical characterization, index properties, and undrained cyclic triaxial tests on isotropically consolidated reconstituted samples. Due to the large variation in the calcareous sand properties, results are compared with previous researches carried out on other calcareous sands around the world. Results showed a wide range in the liquefaction resistance of the studied calcareous sands. Cabo Rojo sand experienced greater liquefaction resistance than most of the calcareous sands used for comparison. Important differences in the excess pore pressure generation characteristics were also found.

  13. DRUG RESISTANCE IN HELICOBACTER PYLORI

    Directory of Open Access Journals (Sweden)

    Júlia Silveira VIANNA

    Full Text Available ABSTRACT Background Helicobacter pylori has a worldwide distribution and is associated with the pathogenesis of various diseases of the digestive system. Treatment to eradicate this microorganism involves the use of a combination of antimicrobials, such as amoxicillin, metronidazole, clarithromycin, and levofloxacin, combined with proton pump inhibitors. Although the current therapy is effective, a high rate of treatment failure has been observed, mainly because of the acquisition of point mutations, one of the major resistance mechanisms developed by H. pylori. This phenomenon is related to frequent and/or inappropriate use of antibiotics. Conclusion This review reported an overview of the resistance to the main drugs used in the treatment of H. pylori, confirming the hypothesis that antibacterial resistance is a highly local phenomenon and genetic characteristics of a given population can influence which therapy is the most appropriate.

  14. Rapid report acetamiprid resistance and cross-resistance in the diamondback moth, Plutella xylostella.

    Science.gov (United States)

    Ninsin, Kodwo D

    2004-09-01

    A 110-fold acetamiprid-resistant Plutella xylostella (L) strain was established after four selection experiments (in five generations) on a 9.5-fold resistant colony in the laboratory. The resistant strain did not show cross-resistance to chlorfluazuron or Bacillus thuringiensis subsp kurstaki Berliner, but displayed low resistance to cartap and phenthoate.

  15. Screening fusarium resistant rootstocks for plant parasitic nematode resistance

    Science.gov (United States)

    The phase out of methyl bromide has directed research toward alternative methods of managing soil-borne pathogens. A limiting factor in many watermelon producing regions is Fusarium wilt caused by the soil-borne fungi Fusarium oxysporum f.sp. niveum (FON). There is no varietal resistance to FON depl...

  16. Plasmid mediated resistance in multidrug resistant bacteria isolated ...

    African Journals Online (AJOL)

    The antibiotic susceptibility testing of isolated bacteria associated with septicaemia in children were carried out using standard microbiological protocol. The MAR index for the test bacterial isolates was determined and the bacterial isolates that displayed multiple antibiotic resistance were investigated for the presence of ...

  17. Insulin resistance in dairy cows.

    Science.gov (United States)

    De Koster, Jenne D; Opsomer, Geert

    2013-07-01

    Glucose is the molecule that drives milk production, and insulin plays a pivotal role in the glucose metabolism of dairy cows. The effect of insulin on the glucose metabolism is regulated by the secretion of insulin by the pancreas and the insulin sensitivity of the skeletal muscles, the adipose tissue, and the liver. Insulin resistance may develop as part of physiologic (pregnancy and lactation) and pathologic processes, which may manifest as decreased insulin sensitivity or decreased insulin responsiveness. A good knowledge of the normal physiology of insulin is needed to measure the in vivo insulin resistance of dairy cows. Copyright © 2013 Elsevier Inc. All rights reserved.

  18. Computing motion using resistive networks

    Science.gov (United States)

    Koch, Christof; Luo, Jin; Mead, Carver; Hutchinson, James

    1988-01-01

    Recent developments in the theory of early vision are described which lead from the formulation of the motion problem as an ill-posed one to its solution by minimizing certain 'cost' functions. These cost or energy functions can be mapped onto simple analog and digital resistive networks. It is shown how the optical flow can be computed by injecting currents into resistive networks and recording the resulting stationary voltage distribution at each node. These networks can be implemented in cMOS VLSI circuits and represent plausible candidates for biological vision systems.

  19. Reflections on researching rape resistance.

    Science.gov (United States)

    Ullman, Sarah E

    2014-03-01

    This article provides a retrospective account of my experience embarking on research about women's resistance to rape, including reflections on personal and professional experiences related to studying this topic. I discuss factors inspiring my interest, including pioneering feminist rape researchers, my experience as a woman living with the reality and fear of rape, and influential mentors who facilitated my career development as a scholar in graduate school and beyond. I weave this narrative together with my thoughts about how the study of resistance relates to other important issues in the field of sexual assault including alcohol, recovery, and prevention.

  20. Radioactive resistance of EEPROM components

    International Nuclear Information System (INIS)

    Loncar, B.; Novakovic, D.; Stankovic, S.; Osmokrovic, P.

    1999-01-01

    The aim of this paper is to examine the resistance of EEPROM components under the influence of gamma radiation. This paper is significant for military industry and space technology. Therefore the analysis of the degradation mechanisms of these components as well as the possibilities to increase their radiation resistance have been considered by many authors. Total dose results are presented for 28C64C EEPROM there is evidence that the first failure appeared for 1000 Gy total dose level. The obtained result are analyzed and explained theoretically via the interaction of gamma radiation with oxide layer. (author)

  1. Corrosion-resistant coating development

    Energy Technology Data Exchange (ETDEWEB)

    Stinton, D.P.; Kupp, D.M.; Martin, R.L. [Oak Ridge National Lab., TN (United States)

    1997-12-01

    SiC-based heat exchangers have been identified as the prime candidate material for use as heat exchangers in advanced combined cycle power plants. Unfortunately, hot corrosion of the SiC-based materials created by alkali metal salts present in the combustion gases dictates the need for corrosion-resistant coatings. The well-documented corrosion resistance of CS-50 combined with its low (and tailorable) coefficient of thermal expansion and low modulus makes CS-50 an ideal candidate for this application. Coatings produced by gelcasting and traditional particulate processing have been evaluated.

  2. Radiation-resistant camera tube

    International Nuclear Information System (INIS)

    Kuwahata, Takao; Manabe, Sohei; Makishima, Yasuhiro

    1982-01-01

    It was a long time ago that Toshiba launched on manufacturing black-and-white radiation-resistant camera tubes employing nonbrowning face-plate glass for ITV cameras used in nuclear power plants. Now in compliance with the increasing demand in nuclear power field, the Company is at grips with the development of radiation-resistant single color-camera tubes incorporating a color-stripe filter for color ITV cameras used under radiation environment. Herein represented are the results of experiments on characteristics of materials for single color-camera tubes and prospects for commercialization of the tubes. (author)

  3. Concretes with high mechanical resistance

    International Nuclear Information System (INIS)

    Mauny, Pierre.

    1973-01-01

    Description is given of a method for manufacturing concretes with high mechanical resistance in compression, obtained by mixing gravels highly resistant to compression, sand and cement in an aqueous medium. Use is made of sands of porous ceramics, such as terra-cotta, of a grain size from 0,1 to 5mm, the pore diameter of which is from 0.5 to 15 microns, chosen so as to be slighty bigger than the crystals of the cement used. This can be applied to the pre-stressed structures used in the nuclear field [fr

  4. Giant magneto-resistance devices

    CERN Document Server

    Hirota, Eiichi; Inomata, Koichiro

    2002-01-01

    This book deals with the application of giant magneto-resistance (GMR) effects to electronic devices. It will appeal to engineers and graduate students in the fields of electronic devices and materials. The main subjects are magnetic sensors with high resolution and magnetic read heads with high sensitivity, required for hard-disk drives with recording densities of several gigabytes. Another important subject is novel magnetic random-access memories (MRAM) with non-volatile non-destructive and radiation-resistant characteristics. Other topics include future GMR devices based on bipolar spin transistors, spin field-effect transistors (FETs) and double-tunnel junctions.

  5. Influence of Addition of Carboxyl Functionalized MWCNTs on Performance of Neat and Carbon Fiber Reinforced EPON 862

    Science.gov (United States)

    2013-05-01

    8.5 Comparison of absorbed energy among neat and various MWCNT doped samples (a) Total energy (b) Energy @ Peak load and (c) Delamination...automotive and recreational sports industries [1–5]. Generally, multiple fabric layers are arranged in a specific sequence and bonded together by a...50, 86]. Figure 31 shows load vs. time and energy vs. time response of neat and various concentration of CNT doped samples at different impact

  6. Inheritance of Cry1F resistance, cross-resistance and frequency of resistant alleles in Spodoptera frugiperda (Lepidoptera: Noctuidae).

    Science.gov (United States)

    Vélez, A M; Spencer, T A; Alves, A P; Moellenbeck, D; Meagher, R L; Chirakkal, H; Siegfried, B D

    2013-12-01

    Transgenic maize, Zea maize L., expressing the Cry1F protein from Bacillus thuringiensis has been registered for Spodoptera frugiperda (J. E. Smith) control since 2003. Unexpected damage to Cry1F maize was reported in 2006 in Puerto Rico and Cry1F resistance in S. frugiperda was documented. The inheritance of Cry1F resistance was characterized in a S. frugiperda resistant strain originating from Puerto Rico, which displayed >289-fold resistance to purified Cry1F. Concentration-response bioassays of reciprocal crosses of resistant and susceptible parental populations indicated that resistance is recessive and autosomal. Bioassays of the backcross of the F1 generation crossed with the resistant parental strain suggest that a single locus is responsible for resistance. In addition, cross-resistance to Cry1Aa, Cry1Ab, Cry1Ac, Cry1Ba, Cry2Aa and Vip3Aa was assessed in the Cry1F-resistant strain. There was no significant cross-resistance to Cry1Aa, Cry1Ba and Cry2Aa, although only limited effects were observed in the susceptible strain. Vip3Aa was highly effective against susceptible and resistant insects indicating no cross-resistance with Cry1F. In contrast, low levels of cross-resistance were observed for both Cry1Ab and Cry1Ac. Because the resistance is recessive and conferred by a single locus, an F1 screening assay was used to measure the frequency of Cry1F-resistant alleles from populations of Florida and Texas in 2010 and 2011. A total frequency of resistant alleles of 0.13 and 0.02 was found for Florida and Texas populations, respectively, indicating resistant alleles could be found in US populations, although there have been no reports of reduced efficacy of Cry1F-expressing plants.

  7. Design, microfabrication, and characterization of a moulded PDMS/SU-8 inkjet dispenser for a Lab-on-a-Printer platform technology with disposable microfluidic chip.

    Science.gov (United States)

    Bsoul, Anas; Pan, Sheng; Cretu, Edmond; Stoeber, Boris; Walus, Konrad

    2016-08-16

    In this paper, we present a disposable inkjet dispenser platform technology and demonstrate the Lab-on-a-Printer concept, an extension of the ubiquitous Lab-on-a-Chip concept, whereby microfluidic modules are directly integrated into the printhead. The concept is demonstrated here through the integration of an inkjet dispenser and a microfluidic mixer enabling control over droplet composition from a single nozzle in real-time during printing. The inkjet dispenser is based on a modular design platform that enables the low-cost microfluidic component and the more expensive actuation unit to be easily separated, allowing for the optional disposal of the former and reuse of the latter. To limit satellite droplet formation, a hydrophobic-coated and tapered micronozzle was microfabricated and integrated with the fluidics to realize the dispenser. The microfabricated devices generated droplets with diameters ranging from 150-220 μm, depending mainly on the orifice diameter, with printing rates up to 8000 droplets per second. The inkjet dispenser is capable of dispensing materials with a viscosity up to ∼19 mPa s. As a demonstration of the inkjet dispenser function and application, we have printed type I collagen seeded with human liver carcinoma cells (cell line HepG2), to form patterned biological structures.

  8. Multidrug resistance in amoebiasis patients.

    Science.gov (United States)

    Bansal, Devendra; Sehgal, Rakesh; Chawla, Yogesh; Malla, Nancy; Mahajan, R C

    2006-08-01

    Amoebiasis, caused by Entamoeba sp. a protozoan parasite, is a major public health problem in tropical and subtropical countries. The symptomatic patients are treated by specific chemotherapy. However, there are reports of treatment failure in some cases suggesting the possibility of drug resistance. The present study was therefore planned to assess the presence and expression of mRNA of multidrug resistance (MDR) gene in clinical isolates of Entamoeba histolytica and E. dispar. Forty five clinical isolates of Entamoeba sp. [E. histolytica (15) and E. dispar (30)] were maintained in polyxenic followed by monoxenic medium. DNA and total RNA were extracted from clinical isolates of Entamoeba sp. and from sensitive strain of E. histolytica (HM1: IMSS) and subjected to polymerase chain reaction (PCR) and multiplex reverse transcription (RT)-PCR techniques. The 344 bp segment of E. histolytica DNA was seen by PCR using primers specific to EhPgp1 in all clinical isolates and sensitive strain of E. histolytica. Over expression of EhPgp1 was observed only in resistant mutant of E. histolytica; however, transcription of EhPgp1 was not seen in any clinical isolates and sensitive strain of E. histolytica. The findings of the present study indicate that, so far, drug resistance in clinical isolates of E. histolytica does not seem to be a major problem in this country. However, susceptibility of clinical isolates of E. histolytica against various antiamoebic drugs needs to be investigated for better management.

  9. Nanoscale organic ferroelectric resistive switches

    NARCIS (Netherlands)

    Khikhlovskyi, V.; Wang, R.; Breemen, A.J.J.M. van; Gelinck, G.H.; Janssen, R.A.J.; Kemerink, M.

    2014-01-01

    Organic ferroelectric resistive switches function by grace of nanoscale phase separation in a blend of a semiconducting and a ferroelectric polymer that is sandwiched between metallic electrodes. In this work, various scanning probe techniques are combined with numerical modeling to unravel their

  10. (Neovossia indica ) resistance in wheat

    Indian Academy of Sciences (India)

    Unknown

    Screening and multiplication of different wheat varieties under laboratory conditions using in vitro culture techniques may speed up the resistance breeding programmes. Hence, the present investigations were planned to study the nature and magnitude of gene effects of inhibition zone formed by the wheat embryos, callus-.

  11. Consumption expressions of ideological resistance

    NARCIS (Netherlands)

    Russell, C.A.; Russell, D.W.; Neijens, P.C.

    2011-01-01

    Purpose - The paper focuses on resistance driven by animosity toward a country due to cultural, political, military and economic reasons. Previous research has linked animosity toward a given country to explicit judgments and purchases of products from that country, thus ignoring the possibility

  12. Nutritional Modulation of Insulin Resistance

    Directory of Open Access Journals (Sweden)

    Martin O. Weickert

    2012-01-01

    Full Text Available Insulin resistance has been proposed as the strongest single predictor for the development of Type 2 Diabetes (T2DM. Chronic oversupply of energy from food, together with inadequate physical activity, have been recognized as the most relevant factors leading to overweight, abdominal adiposity, insulin resistance, and finally T2DM. Conversely, energy reduced diets almost invariably to facilitate weight loss and reduce abdominal fat mass and insulin resistance. However, sustained weight loss is generally difficult to achieve, and distinct metabolic characteristics in patients with T2DM further compromise success. Therefore, investigating the effects of modulating the macronutrient composition of isoenergetic diets is an interesting concept that may lead to additional important insights. Metabolic effects of various different dietary concepts and strategies have been claimed, but results from randomized controlled studies and particularly from longer-term-controlled interventions in humans are often lacking. However, some of these concepts are supported by recent research, at least in animal models and short-term studies in humans. This paper provides an update of the current literature regarding the role of nutrition in the modulation of insulin resistance, which includes the discussion of weight-loss-independent metabolic effects of commonly used dietary concepts.

  13. Fire resistant nuclear fuel cask

    International Nuclear Information System (INIS)

    Heckman, R.C.; Moss, M.

    1979-01-01

    The disclosure is directed to a fire resistant nuclear fuel cask employing reversibly thermally expansible bands between adjacent cooling fins such that normal outward flow of heat is not interfered with, but abnormal inward flow of heat is impeded or blocked

  14. Pathophysiological mechanisms of insulin resistance

    NARCIS (Netherlands)

    Brands, M.

    2013-01-01

    In this thesis we studied pathophysiological mechanisms of insulin resistance in different conditions in humans, i.e. in obesity, during lipid infusions, after hypercaloric feeding, and glucocorticoid treatment. We focused on 3 important hypotheses that are suggested to be implicated in the

  15. Extensively Drug-Resistant TB

    Centers for Disease Control (CDC) Podcasts

    2016-12-16

    Dr. Charlotte Kvasnovsky, a surgery resident and Ph.D. candidate in biostatistics, discusses various types of drug resistance in TB patients in South Africa.  Created: 12/16/2016 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 12/16/2016.

  16. The Internal Resistance of Supercapacitors

    Science.gov (United States)

    Costa, G. G. G.; Pietronero, R. C.; Catunda, T.

    2012-01-01

    In this paper we study the transient behaviour of RC circuits with supercapacitors, varying R between 1 and 100 [omega]. We demonstrate that supercapacitors behave as ideal capacitors in series with an internal resistance (r [similar to] 8 [omega] for C = 0.2 F, 5.5 V). This result is important to optimize the demonstration of RC circuits using a…

  17. Resistive flex sensors: a survey

    International Nuclear Information System (INIS)

    Saggio, Giovanni; Riillo, Francesco; Sbernini, Laura; Quitadamo, Lucia Rita

    2016-01-01

    Resistive flex sensors can be used to measure bending or flexing with relatively little effort and a relatively low budget. Their lightness, compactness, robustness, measurement effectiveness and low power consumption make these sensors useful for manifold applications in diverse fields. Here, we provide a comprehensive survey of resistive flex sensors, taking into account their working principles, manufacturing aspects, electrical characteristics and equivalent models, useful front-end conditioning circuitry, and physic-bio-chemical aspects. Particular effort is devoted to reporting on and analyzing several applications of resistive flex sensors, related to the measurement of body position and motion, and to the implementation of artificial devices. In relation to the human body, we consider the utilization of resistive flex sensors for the measurement of physical activity and for the development of interaction/interface devices driven by human gestures. Concerning artificial devices, we deal with applications related to the automotive field, robots, orthosis and prosthesis, musical instruments and measuring tools. The presented literature is collected from different sources, including bibliographic databases, company press releases, patents, master’s theses and PhD theses. (topical review)

  18. Antimicrobial Drug Resistance and Gonorrhea

    Centers for Disease Control (CDC) Podcasts

    2017-12-26

    Dr. Robert Kirkcaldy, a medical officer at CDC, discusses his article on antimicrobial resistance and gonorrhea.  Created: 12/26/2017 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 12/26/2017.

  19. BALLISTIC RESISTANT ARTICLES COMPRISING TAPES

    NARCIS (Netherlands)

    VAN DER EEM, JORIS; HARINGS, JULES; JANSE, GERARDUS; TJADEN, HENDRIK

    2015-01-01

    The invention pertains to a ballistic-resistant moulded article comprising a compressed stack of sheets comprising reinforcing tapes having a tensile strength of at least 1.0 GPa, a tensile modulus of at least 40 GPa, and a tensile energy-to-break of at least 15 J/g, the direction of the tapes

  20. Molecular mechanism of insulin resistance

    Indian Academy of Sciences (India)

    Free fatty acids are known to play a key role in promoting loss of insulin sensitivity, thereby causing insulin resistance and type 2 diabetes. However, the underlying mechanism involved is still unclear. In searching for the cause of the mechanism, it has been found that palmitate inhibits insulin receptor (IR) gene expression, ...