WorldWideScience

Sample records for epics controlled sample

  1. EPICS controlled sample mounting robots at the GM/CA CAT

    Energy Technology Data Exchange (ETDEWEB)

    Makarov, O.A. [GM/CA-CAT, Biosciences Division, Argonne National Laboratory, 9700 South Cass Avenue, Bldg. 436D, Argonne, IL 60439-4861 (United States)], E-mail: makarov@anl.gov; Benn, R.; Corcoran, S.; Devarapalli, S.; Fischetti, R.; Hilgart, M.; Smith, W.W.; Stepanov, S.; Xu, S. [GM/CA-CAT, Biosciences Division, Argonne National Laboratory, 9700 South Cass Avenue, Bldg. 436D, Argonne, IL 60439-4861 (United States)

    2007-11-11

    GM/CA CAT at Sector 23 of the advanced photon source (APS) is an NIH funded facility for crystallographic structure determination of biological macromolecules by X-ray diffraction [R.F. Fischetti, et al., GM/CA canted undulator beamlines for protein crystallography, Acta Crystallogr. A 61 (2005) C139]. The facility consists of three beamlines; two based on canted undulators and one on a bending magnet. The scientific and technical goals of the CAT emphasize streamlined, efficient throughput for a variety of sample types, sizes and qualities, representing the cutting edge of structural biology research. For this purpose all three beamlines are equipped with the ALS-style robots [C.W.Cork, et al. Status of the BCSB automated sample mounting and alignment system for macromolecular crystallography at the Advanced Light Source, SRI-2003, San-Francisco, CA, USA, August 25-29, 2003] for an automated mounting of cryo-protected macromolecular crystals. This report summarizes software and technical solutions implemented with the first of the three operational robots at beamline 23-ID-B. The automounter's Dewar can hold up to 72 or 96 samples residing in six Rigaku ACTOR magazines or ALS-style pucks, respectively. Mounting of a crystal takes approximately 2 s, during which time the temperature of the crystal is maintained near that of liquid nitrogen.

  2. EPICS application source/release control

    International Nuclear Information System (INIS)

    Zieman, B.; Anderson, J.; Kraimer, M.

    1995-01-01

    This manual describes a set of Application Source/Release Control tools (appSR) that can be used to develop software for EPICS based control systems. The Application Source/Release Control System (appSR) has been unbundled from base EPICS and is now available as an EPICS extension. Due to this unbundling, two new directories must be added to a user's path (see section ''Environment'' on page 3 for more information) and a new command getapp must be issued after the getrel command to get a specific version of appSR (see section ''Creating The Initial Application System Area'' on page 7 for more information). It is now required that GNU make version 3.71 or later be used for makes instead of SUN make. Users should now type gmake instead of make

  3. EPICS Controlled Collimator for Controlling Beam Sizes in HIPPO

    Energy Technology Data Exchange (ETDEWEB)

    Napolitano, Arthur Soriano [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Vogel, Sven C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-03

    Controlling the beam spot size and shape in a diffraction experiment determines the probed sample volume. The HIPPO - High-Pressure-Preferred Orientation– neutron time-offlight diffractometer is located at the Lujan Neutron Scattering Center in Los Alamos National Laboratories. HIPPO characterizes microstructural parameters, such as phase composition, strains, grain size, or texture, of bulk (cm-sized) samples. In the current setup, the beam spot has a 10 mm diameter. Using a collimator, consisting of two pairs of neutron absorbing boron-nitride slabs, horizontal and vertical dimensions of a rectangular beam spot can be defined. Using the HIPPO robotic sample changer for sample motion, the collimator would enable scanning of e.g. cylindrical samples along the cylinder axis by probing slices of such samples. The project presented here describes implementation of such a collimator, in particular the motion control software. We utilized the EPICS (Experimental Physics Interface and Control System) software interface to integrate the collimator control into the HIPPO instrument control system. Using EPICS, commands are sent to commercial stepper motors that move the beam windows.

  4. Development of EPICS based beam-line experimental control employing motor controller for precision positioning

    International Nuclear Information System (INIS)

    Tuli, Anupriya; Jain, Rajiv; Vora, H.S.

    2015-01-01

    In a Synchrotron Radiation Source the beamline experiments are carried out in radiation prone environment, inside the hutch, which demands to conduct experiments remotely. These experiments involves instrument control and data acquisition from various devices. Another factor which attributes to system complexity is precise positioning of sample and placement of detectors. A large number of stepper motors are engaged for achieving the required precision positioning. This work is a result of development of Experimental Physics and Industrial Control System (EPICS) based control system to interface a stepper motor controller developed indigenously by Laser Electronics Support Division of RRCAT. EPICS is an internationally accepted open source software environment which follows toolkit approach and standard model paradigm. The operator interface for the control system software was implemented using CSS BOY. The system was successfully tested for Ethernet based remote access. The developed control software comprises of an OPI and alarm handler (EPICS ALH). Both OPI and ALH are linked with PV's defined in database files. The development process resulted into a set of EPICS based commands for controlling stepper motor. These commands are independent of operator interface, i.e. stepper motor can be controlled by using these set of commands directly on EPICS prompt. This command set is illustrated in the above table. EPICS Alarm Handler was also tested independently by running these commands on EPIC prompt. If not using ALH, operator can read the alarm status of a PV using 'SEVR' and 'STAT' attributes. (author)

  5. EPICS and its role in data acquisition and beamline control

    International Nuclear Information System (INIS)

    Mooney, T. M.; Arnold, N. D.; Boucher, E.; Cha, B. K.; Goetze, K. A.; Kraimer, M. R.; Rivers, M. L.; Sluiter, R. L.; Sullivan, J. P.; Wallis, D. B.

    1999-01-01

    Beamline-control and data-acquisition software based on EPICS (a tool kit for building distributed control systems) has been running on many Advanced Photon Source beamlines for several years. EPICS itself, the collaborative software-development effort surrounding it, and EPICS-based beamline software have been described previously in general terms. This talk will review and update that material, focusing on the role EPICS core software plays in beamline applications and on the effects of a few defining characteristics of EPICS on the beamline software we have developed with it

  6. EPICS: Experimental Physics and Industrial Control System

    Science.gov (United States)

    Epics Development Team

    2013-02-01

    EPICS is a set of software tools and applications developed collaboratively and used to create distributed soft real-time control systems for scientific instruments such as particle accelerators and telescopes. Such distributed control systems typically comprise tens or even hundreds of computers, networked together to allow communication between them and to provide control and feedback of the various parts of the device from a central control room, or even remotely over the internet. EPICS uses Client/Server and Publish/Subscribe techniques to communicate between the various computers. A Channel Access Gateway allows engineers and physicists elsewhere in the building to examine the current state of the IOCs, but prevents them from making unauthorized adjustments to the running system. In many cases the engineers can make a secure internet connection from home to diagnose and fix faults without having to travel to the site. EPICS is used by many facilities worldwide, including the Advanced Photon Source at Argonne National Laboratory, Fermilab, Keck Observatory, Laboratori Nazionali di Legnaro, Brazilian Synchrotron Light Source, Los Alamos National Laboratory, Australian Synchrotron, and Stanford Linear Accellerator Center.

  7. Monitor and Control for PEFP System using EPICS

    International Nuclear Information System (INIS)

    Choi, Hyun Mi; Hong, I. S.; Song, Y. G.; Cho, Y. S.

    2005-01-01

    The construction of PEFP project whose final objective is to build 100 Mev proton accelerator started in 2002 and expected to finish in 2012. In 2005, we have performed 20mA proton beam of 20Mev. For developing the control systems of the 20Mev accelerator as well as 100 Mev accelerator, we chose EPICS(Experimental Physics and Industrial Control System) as the most suitable tool. We have studied EPICS applications for various situation and as the application we developed vacuum control system using EPICS base3.14.4 as the core software and EPICS extensions (e.g., EDM(Extensible Display Manager), MEDM(Motif Editor and Display Manager) etc.) as the user interface. There are a number of projects using EPICS for a broad spectrum of applications. EPICS began as a collaboration between Argonne National Laboratory and Los Alamos National Laboratory in 1991, building on work that was initially done at the ground test Accelerator. It is now running on accelerators that have as many as 180 distributed front-end controllers and control rooms with 20 consoles and a gateway to make system parameters available to offices, web site, and other remote control stations. It is also used at single controller and one workstation systems. We use the EPICS tool kit as a foundation of the control system. We developed a vacuum monitor, RFQ, DTL Turbo pump control system for use Ethernet Multi Serial Deice Severs on PEFP control system. The control system now shows stable and reliable characteristics enough to meet our control requirement. However, the control system is continuously being upgraded to accommodate additional control requirements such as vacuum device control

  8. Qt based GUI system for EPICS control systems

    International Nuclear Information System (INIS)

    Rhyder, A.; Fernandes, R.N.; Starritt, A.

    2012-01-01

    The Qt-based GUI system developed at the Australian Synchrotron for use on EPICS control systems has recently been enhanced to including support for imaging, plotting, user login, logging and configuration recipes. Plans are also being made to broaden its appeal within the wider EPICS community by expanding the range of development options and adding support for EPICS V4. Current features include graphical and non-graphical application development as well as simple 'code-free' GUI design. Additional features will allow developers to let the GUI system handle its own data using Qt-based EPICS-aware classes or, as an alternative, use other control systems data such as PSI's CAFE. (author)

  9. The KSTAR integrated control system based on EPICS

    International Nuclear Information System (INIS)

    Kim, K.H.; Ju, C.J.; Kim, M.K.; Park, M.K.; Choi, J.W.; Kyum, M.C.; Kwon, M.

    2006-01-01

    The Korea Superconducting Tokamak Advanced Research (KSTAR) control system will be developed with several subsystems, which consist of the central control system (e.g. plasma control, machine control, diagnostic control, time synchronization, and interlock systems) and local control systems for various subsystems. We are planning to connect the entire system with several networks, viz. a reflective-memory-based real-time network, an optical timing network, a gigabit Ethernet network for generic machine control, and a storage network. Then it will evolve into a network-based, distributed real-time control system. Thus, we have to consider the standard communication protocols among the subsystems and how to handle the various kinds of hardware in a homogeneous way. To satisfy these requirements, EPICS has been chosen for the KSTAR control. The EPICS framework provides network-based real-time distributed control, operating system independent programming tools, operator interface tools, archiving tools, and interface tools with other commercial and non-commercial software. The most important advantage of the use of the EPICS framework is in providing homogeneity of the system for the control system developer. The developer does not have to be concerned about the specifics of the local system, but can concentrate on the implementation of the control logic with EPICS tools. We will present the details of the integration issues and also will give a brief summary of the entire KSTAR control system from an integration point of view

  10. EPICS: A control system software co-development success story

    International Nuclear Information System (INIS)

    Knott, M.; Gurd, D.; Lewis, S.; Thuot, M.

    1993-01-01

    The Experimental Physics and Industrial Control Systems (EPICS) is the result of a software sharing and co-development effort of major importance now underway. The initial two participants, LANL and ANL, have now been joined by three other labs, and an earlier version of the software has been transferred to three commercial firms and is currently undergoing separate development. The reasons for EPICS's success may be useful to enumerate and explain and the desire and prospects for its continued development are certainly worth examining

  11. EPICS-QT based graphical user interface for accelerator control

    International Nuclear Information System (INIS)

    Basu, A.; Singh, S.K.; Rosily, Sherry; Bhagwat, P.V.

    2016-01-01

    Particle accelerators and many industrial complex systems, require a robust and efficient control for its proper operation to achieve required beam quality, safety of its sub component and all working personnel. This control is executed via a graphical user interface through which an operator interacts with the accelerator to achieve the desired state of the machine and its output. Experimental Physics and Industrial Control System (EPICS) is a widely used control system framework in the field of accelerator control. It acts as a middle layer between field devices and graphic user interface used by the operator. Field devices can also be made EPICS compliant by using EPICS based software in that. On the other hand Qt is a C++ framework which is widely used for creating very professional looking and user friendly graphical component. In Low Energy High Intensity Proton Accelerator (LEHIPA), which is the first stage of the three stage Accelerator Driven System (ADS) program taken by Bhabha Atomic Research Centre (BARC), it is decided that EPICS will be used for controlling the accelerator and Qt will be used for developing the various Graphic User Interface (GUI) for operation and diagnostics. This paper discuss the work carried out to achieve this goal in LEHIPA

  12. Construction of a remote controlled monitoring system with GPIB devices and EPICS

    International Nuclear Information System (INIS)

    Yoshikawa, Takeshi; Yamamoto, Noboru.

    1995-01-01

    The Experimental Physics and Industrial Control System (EPICS) has been used for the accelerator control system in recent years. EPICS has rich set of tools to create application with Graphical User Interface (GUI). It reduces the load of complex programming for GUI and shortens the application development period. This paper will describe the remote temperature monitoring system using EPICS. (author)

  13. EPICS based control system for cryogenic plant at VECC

    International Nuclear Information System (INIS)

    Panda, Umashankar; Pal, Sandip; Mandal, Anupam; Dey, Ranadhir

    2012-01-01

    Cryogenic Plant of Variable Energy Cyclotron Centre consists of two Helium refrigerators (250W and 415W at the rate 4.5K), valve box with sub-cooler and associated sub systems like pure gas storage, helium purifier and impure gas recovery etc. The system also consists of 3.1K liters of liquid Nitrogen (LN 2 ) storage and delivery system. Many of the systems are procured from different suppliers and some are also developed in house. Due to the variety of systems and suppliers the control philosophy, communication protocols and component is also different. So the Supervisory control and data acquisition (SCADA) module has to be such that it can take care of the variance and bring everything into a common control platform. To solve this purpose EPICS (Experimental Physics and Industrial Control System) architecture has been adopted. EPICS is having the advantage of being open source, flexible and unlimited as compared to the commercial SCADA packages. (author)

  14. Integrating EPICS and MDSplus

    International Nuclear Information System (INIS)

    Mastrovito, D.; Davis, W.; Dong, J.; Roney, P.; Sichta, P.

    2006-01-01

    The National Spherical Torus Experiment (NSTX) has been in operation at the Princeton Plasma Physics Laboratory (PPPL) since 1999. Since then, NSTX has made use of the Experimental Physics and Industrial Control System (EPICS) and MDSplus software packages, among others for control and data acquisition. To date, the two products have been integrated using special 'bridging' programs that include client-components for the EPICS and MDSplus servers. Recent improvements in the EPICS software have made it easier to develop a direct interface with MDSplus. This paper will describe the new EPICS extensions developed at PPPL that provide: (1) a direct data interface between EPICS process variables and MDSplus nodes; and (2) an interface between EPICS events and MDSplus events. These extensions have been developed for use with EPICS on Solaris and are currently being modified for use on real-time operating systems. Separately, an XML-RPC client was written to access EPICS 'trended' data, sampled usually once per minute during a 24 h period. The client extracts and writes a day's worth of trended data to a 'daily' MDSplus tree

  15. Monitoring commercial conventional facilities control with the APS control system: The Metasys-to-EPICS interface

    International Nuclear Information System (INIS)

    Nawrocki, G.J.; Seaver, C.L.; Kowalkowski, J.B.

    1995-01-01

    As controls needs at the Advanced Photon Source matured from an installation phase to an operational phase, the need to monitor the existing conventional facilities control system with the EPICS-based accelerator control system was realized. This existing conventional facilities control network is based on a proprietary system from Johnson Controls called Metasys. Initially read-only monitoring of the Metasys parameters will be provided; however, the ability for possible future expansion to full control is available. This paper describes a method of using commercially available hardware and existing EPICS software as a bridge between the Metasys and EPICS control systems

  16. An object oriented framework of EPICS for MicroTCA based control system

    International Nuclear Information System (INIS)

    Geng, Z.

    2012-01-01

    EPICS (Experimental Physics and Industrial Control System) is a distributed control system platform which has been widely used for large scientific devices control like particle accelerators and fusion plant. EPICS has introduced object oriented (C ++ ) interfaces to most of the core services. But the major part of EPICS, the run-time database, only provides C interfaces, which is hard to involve the EPICS record concerned data and routines in the object oriented architecture of the software. This paper presents an object oriented framework which contains some abstract classes to encapsulate the EPICS record concerned data and routines in C ++ classes so that full OOA (Objected Oriented Analysis) and OOD (Object Oriented Design) methodologies can be used for EPICS IOC design. We also present a dynamic device management scheme for the hot swap capability of the MicroTCA based control system. (authors)

  17. Experimental Physics and Industrial Control System (EPICS): Application source/release control for EPICS R3.11.6

    International Nuclear Information System (INIS)

    Zieman, B.; Kraimer, M.

    1994-01-01

    This manual describes a set of tools that can be used to develop software for EPICS based control systems. It provides the following features: Multiple applications; the entire system is composed of an arbitrary number of applications: Source/Release Control; all files created or modified by the applications developers can be put under sccs (a UNIX Source/Release control utility): Multiple Developers; it allows a number of applications developers to work separately during the development phase but combine their applications for system testing and for a production system; Makefiles: makefiles are provided to automatically rebuild various application components. For C and state notation programs, Imagefiles are provided

  18. JBluIce-EPICS control system for macromolecular crystallography

    International Nuclear Information System (INIS)

    Stepanov, S.; Makarov, O.; Hilgart, M.; Pothineni, S.; Urakhchin, A.; Devarapalli, S.; Yoder, D.; Becker, M.; Ogata, C.; Sanishvili, R.; Nagarajan, V.; Smith, J.L.; Fischetti, R.F.

    2011-01-01

    The trio of macromolecular crystallography beamlines constructed by the General Medicine and Cancer Institutes Collaborative Access Team (GM/CA-CAT) in Sector 23 of the Advanced Photon Source (APS) have been in growing demand owing to their outstanding beam quality and capacity to measure data from crystals of only a few micrometres in size. To take full advantage of the state-of-the-art mechanical and optical design of these beamlines, a significant effort has been devoted to designing fast, convenient, intuitive and robust beamline controls that could easily accommodate new beamline developments. The GM/CA-CAT beamline controls are based on the power of EPICS for distributed hardware control, the rich Java graphical user interface of Eclipse RCP and the task-oriented philosophy as well as the look and feel of the successful SSRL BluIce graphical user interface for crystallography. These beamline controls feature a minimum number of software layers, the wide use of plug-ins that can be written in any language and unified motion controls that allow on-the-fly scanning and optimization of any beamline component. This paper describes the ways in which BluIce was combined with EPICS and converted into the Java-based JBluIce, discusses the solutions aimed at streamlining and speeding up operations and gives an overview of the tools that are provided by this new open-source control system for facilitating crystallographic experiments, especially in the field of microcrystallography.

  19. Controlling EPICS from a web browser

    International Nuclear Information System (INIS)

    Evans, K. Jr.

    1999-01-01

    An alternative to using a large graphical display manager like MEDM [1,2] to interface to a control system, is to use individual control objects, such as text boxes, meters, etc., running in a browser. This paper presents three implementations of this concept, one using ActiveX controls, one with Java applets, and another with Microsoft Agent. The ActiveX controls have performance nearing that of MEDM, but they only work on Windows platforms. The Java applets require a server to get around Web security restrictions and are not as fast, but they have the advantage of working on most platforms and with both of the leading Web browsers. The agent works on Windows platforms with and without a browser and allows voice recognition and speech synthesis, making it somewhat more innovative than MEDM

  20. EPICS-based control and data acquisition for the APS slope profiler (Conference Presentation)

    Science.gov (United States)

    Sullivan, Joseph; Assoufid, Lahsen; Qian, Jun; Jemian, Peter R.; Mooney, Tim; Rivers, Mark L.; Goetze, Kurt; Sluiter, Ronald L.; Lang, Keenan

    2016-09-01

    The motion control, data acquisition and analysis system for APS Slope Measuring Profiler was implemented using the Experimental Physics and Industrial Control System (EPICS). EPICS was designed as a framework with software tools and applications that provide a software infrastructure used in building distributed control systems to operate devices such as particle accelerators, large experiments and major telescopes. EPICS was chosen to implement the APS Slope Measuring Profiler because it is also applicable to single purpose systems. The control and data handling capability available in the EPICS framework provides the basic functionality needed for high precision X-ray mirror measurement. Those built in capabilities include hardware integration of high-performance motion control systems (3-axis gantry and tip-tilt stages), mirror measurement devices (autocollimator, laser spot camera) and temperature sensors. Scanning the mirror and taking measurements was accomplished with an EPICS feature (the sscan record) which synchronizes motor positioning with measurement triggers and data storage. Various mirror scanning modes were automatically configured using EPICS built-in scripting. EPICS tools also provide low-level image processing (areaDetector). Operation screens were created using EPICS-aware GUI screen development tools.

  1. Using EPICS enabled industrial hardware for upgrading control systems

    International Nuclear Information System (INIS)

    Bjorkland, Eric A.; Veeramani, Arun; Debelle, Thierry

    2009-01-01

    Los Alamos National Laboratory has been working with National Instruments (NI) and Cosy lab to implement EPICS Input Output Controller (IOC) software that runs directly on NI CompactRIO Real Time Controller (RTC) and communicates with NI LabVIEW through a shared memory interface. In this presentation, we will discuss our current progress in upgrading the control system at the Los Alamos Neutron Science Centre (LANSCE) and what we have learned about integrating CompactRIO into large experimental physics facilities. We will also discuss the implications of using Channel Access Server for LabVIEW which will enable more commercial hardware platforms to be used in upgrading existing facilities or in commissioning new ones.

  2. Implementation of EPICS based Control System for Radioisotope Beam line

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jae-Ha; Ahn, Tae-Sung; Song, Young-Gi; Kwon, Hyeok-Jung; Cho, Yong-Sub [Korea Atomic Energy Research Institute, Gyeongju (Korea, Republic of)

    2015-10-15

    Korea Mult-purpose Accelerator Complex (KOMAC) has been operating 100 MeV proton linear accelerator . For operating 100 MeV linac, various control system has been implemented such as vacuum, power supply, RCCS and etc. KOMAC is operating two beam lines so that clients can use 100 MeV proton beam for their experiment. KOMAC sends beam to beam line and target room using two dipole magnets and several quadrupole magnets. As demand for experiments and Radius Isotope using beam is increased, another beam line is under construction and RI beam line control system is need. To synchronize with KOMAC control system, RI beam line control system is based on Experimental Physics and Industrial control System (EPICS) software. The beam is transported to RI beam line to control magnet power supply and vacuum. Implementation of RI beam line control system is presented and some preliminary results are reported. The base RI beam line control system is implemented. It can control beam direction and vacuum. Comparing archived data and current data, RI beam line and control system will be improved. In the future, scroll pump and gate control system will be implemented using programmable logic controller PLC. RI beam interlock sequence will be added to KOMAC interlock system to protect linac.

  3. An autonomous observation and control system based on EPICS and RTS2 for Antarctic telescopes

    Science.gov (United States)

    Zhang, Guang-yu; Wang, Jian; Tang, Peng-yi; Jia, Ming-hao; Chen, Jie; Dong, Shu-cheng; Jiang, Fengxin; Wu, Wen-qing; Liu, Jia-jing; Zhang, Hong-fei

    2016-01-01

    For unattended telescopes in Antarctic, the remote operation, autonomous observation and control are essential. An EPICS-(Experimental Physics and Industrial Control System) and RTS2-(Remote Telescope System, 2nd Version) based autonomous observation and control system with remoted operation is introduced in this paper. EPICS is a set of open source software tools, libraries and applications developed collaboratively and used worldwide to create distributed soft real-time control systems for scientific instruments while RTS2 is an open source environment for control of a fully autonomous observatory. Using the advantage of EPICS and RTS2, respectively, a combined integrated software framework for autonomous observation and control is established that use RTS2 to fulfil the function of astronomical observation and use EPICS to fulfil the device control of telescope. A command and status interface for EPICS and RTS2 is designed to make the EPICS IOC (Input/Output Controller) components integrate to RTS2 directly. For the specification and requirement of control system of telescope in Antarctic, core components named Executor and Auto-focus for autonomous observation is designed and implemented with remote operation user interface based on browser-server mode. The whole system including the telescope is tested in Lijiang Observatory in Yunnan Province for practical observation to complete the autonomous observation and control, including telescope control, camera control, dome control, weather information acquisition with the local and remote operation.

  4. IFMIF LLRF control system architecture based on EPICS

    International Nuclear Information System (INIS)

    Calvo, J.; Ibarra, A.; Miguel Angel Patricio; Rivers, M.

    2012-01-01

    The IFMIF-EVEDA (International Fusion Materials Irradiation Facility - Engineering Validation and Engineering Design Activity) linear accelerator will be a 9 MeV, 125 mA CW (Continuous Wave) deuteron accelerator prototype to validate the technical options of the accelerator design for IFMIF. The primary mission of such facility is to test and verify materials performance when subjected to extensive neutron irradiation of the type encountered in a fusion reactor. The RF (Radio Frequency) power system of IFMIF-EVEDA consists of 18 RF chains working at 175 MHz with three amplification stages each. The LLRF (Low-Level Radio Frequency) controls the amplitude and phase of the signal to be synchronized with the beam and it also controls the resonance frequency of the cavities. The system is based on a commercial cPCI (Compact Peripheral Component Interconnect) FPGA (Field Programmable Gate Array) board provided by Lyrtech and controlled by a Windows Host PC. For this purpose, it is mandatory to communicate the cPCI FPGA Board with an EPICS Channel Access, building an IOC (Input Output Controller). A new software architecture to design a device support, using AsynPortDriver class and CSS as a GUI (Graphical User Interface), is also presented. (authors)

  5. EPICS IOC module development and implementation for the ISTTOK machine subsystem operation and control

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Paulo, E-mail: pricardofc@ipfn.ist.utl.pt [Associacao EURATOM/IST, Instituto de Plasmas e Fusao Nuclear-Laboratorio Associado, Instituto Superior Tecnico, P-1049-001 Lisboa (Portugal); Duarte, Andre; Pereira, Tiago; Carvalho, Bernardo; Sousa, Jorge; Fernandes, Horacio [Associacao EURATOM/IST, Instituto de Plasmas e Fusao Nuclear-Laboratorio Associado, Instituto Superior Tecnico, P-1049-001 Lisboa (Portugal); Correia, Carlos [Grupo de Electronica e Instrumentacao-Centro de Instrumentacao, Departamento de Fisica, Universidade de Coimbra, P-3004-516 Coimbra (Portugal); Goncalves, Bruno; Varandas, Carlos [Associacao EURATOM/IST, Instituto de Plasmas e Fusao Nuclear-Laboratorio Associado, Instituto Superior Tecnico, P-1049-001 Lisboa (Portugal)

    2011-10-15

    This paper presents a developed, tested and integrated EPICS IOC (I/O controller) module solution for the ISTTOK tokamak machine operation and control for the vacuum and gas injection systems. The work is organized in two software layers which communicate through a serial RS-232 communication protocol. The first software layer is an EPICS IOC module running as a computer server application capable of receiving requests from remote or local clients providing driver interface to the system by forwarding requested commands and receiving system and control operation status. The second software layer is the firmware running in Microchip dsPIC microcontroller modules which performs the interface from RS-232 optical fiber serial protocol to EPICS IOC module. The dsPIC module communicates to the ISTTOK tokamak sensors and actuators via RS-485 and is programmed with a new protocol developed for this purpose that allows EPICS IOC module command sending/receiving, machine operation control and monitoring and system status information. Communication between EPICS IOC module and clients is achieved via a TCP/IP and UDP protocol referred as Channel Access. In addition, the EPICS IOC module provides user client applications access allowing operators to perform remote or local monitoring, operation and control.

  6. Design and application of an EPICS compatible slow plant system controller in J-TEXT tokamak

    International Nuclear Information System (INIS)

    Zhang, J.; Zhang, M.; Zheng, W.; Zhuang, G.; Ding, T.

    2014-01-01

    Highlights: • Underlying functionalities are encapsulated into plug-and-play modules. • The slow controller is EPICS compatible. • The slow controller can work as PSH. - Abstract: J-TEXT tokamak has recently implemented J-TEXT COntrol, Data Access and Communication (CODAC) system on the principle of ITER CODAC. The control network in J-TEXT CODAC system is based on Experimental Physics and Industrial Control System (EPICS). However, former slow plant system controllers in J-TEXT did not support EPICS. Therefore, J-TEXT has designed an EPICS compatible slow controller. And moreover, the slow controller also acts the role of Plant System Host (PSH), which helps non-EPICS controllers to keep working in J-TEXT CODAC system. The basic functionalities dealing with user defined tasks have been modularized into driver or plug-in modules, which are plug-and-play and configured with XML files according to specific control task. In this case, developers are able to implement various kinds of control tasks with these reusable modules, regardless of how the lower-lever functions are implemented, and mainly focusing on control algorithm. And it is possible to develop custom-built modules by themselves. This paper presents design of the slow controller. Some applications of the slow controller have been deployed in J-TEXT, and will be introduced in this paper

  7. Design and application of an EPICS compatible slow plant system controller in J-TEXT tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, J.; Zhang, M. [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); College of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Zheng, W., E-mail: zhengwei@hust.edu.cn [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); College of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Zhuang, G.; Ding, T. [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); College of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2014-05-15

    Highlights: • Underlying functionalities are encapsulated into plug-and-play modules. • The slow controller is EPICS compatible. • The slow controller can work as PSH. - Abstract: J-TEXT tokamak has recently implemented J-TEXT COntrol, Data Access and Communication (CODAC) system on the principle of ITER CODAC. The control network in J-TEXT CODAC system is based on Experimental Physics and Industrial Control System (EPICS). However, former slow plant system controllers in J-TEXT did not support EPICS. Therefore, J-TEXT has designed an EPICS compatible slow controller. And moreover, the slow controller also acts the role of Plant System Host (PSH), which helps non-EPICS controllers to keep working in J-TEXT CODAC system. The basic functionalities dealing with user defined tasks have been modularized into driver or plug-in modules, which are plug-and-play and configured with XML files according to specific control task. In this case, developers are able to implement various kinds of control tasks with these reusable modules, regardless of how the lower-lever functions are implemented, and mainly focusing on control algorithm. And it is possible to develop custom-built modules by themselves. This paper presents design of the slow controller. Some applications of the slow controller have been deployed in J-TEXT, and will be introduced in this paper.

  8. The CEBAF accelerator control system: migrating from a TACL to an EPICS based system

    International Nuclear Information System (INIS)

    Watson, W.A. III; Barker, David; Bickley, Matthew; Gupta, Pratik; Johnson, R.P.

    1994-01-01

    CEBAF is in the process of migrating its accelerator and experimental hall control systems to one based upon EPICS, a control system toolkit developed by a collaboration among several DOE laboratories in the US. The new system design interfaces existing CAMAC hardware via a CAMAC serial highway to VME-based I/O controllers running the EPICS software; future additions and upgrades will for the most part go directly into VME. The decision to use EPICS followed difficulties in scaling the CEBAF-developed TACL system to full machine operation. TACL and EPICS share many design concepts, facilitating the conversion of software from one toolkit to the other. In particular, each supports graphical entry of algorithms built up from modular code, graphical displays with a display editor, and a client-server architecture with name-based I/O. During the migration, TACL and EPICS will interoperate through a socket-based I/O gateway. As part of a collaboration with other laboratories, CEBAF will add relational database support for system management and high level applications support. Initial experience with EPICS is presented, along with a plan for the full migration which is expected to be finished next year. ((orig.))

  9. RIO EPICS device support application case study on an ion source control system (ISHP)

    Energy Technology Data Exchange (ETDEWEB)

    Sanz, Diego [UPM – Universidad Politécnica de Madrid, Madrid (Spain); Ruiz, Mariano, E-mail: mariano.ruiz@upm.es [UPM – Universidad Politécnica de Madrid, Madrid (Spain); Eguiraun, Mikel [Department of Electricity and Electronic, Faculty of Science and Technology, University of Basque Country, Bilbao (Spain); Arredondo, Iñigo [ESS Bilbao Consortium, Zamudio (Spain); Badillo, Inari; Jugo, Josu [Department of Electricity and Electronic, Faculty of Science and Technology, University of Basque Country, Bilbao (Spain); Vega, Jesús; Castro, Rodrigo [Asociación EURATOM/CIEMAT, Madrid (Spain)

    2015-10-15

    Highlights: • A use case example of RIO/FlexRIO design methodology is described. • Ion source device is controlled and monitored by means EPICS IOCs. • NIRIO EPICS device support demonstrates that is able to manage RIO devices. • Easy and fast deployment is possible using RIO/FlexRIO design methodology using NIRIO-EDS. • RIO/FlexRIO technology and EPICS are a good combination for support large scale experiments in fusion environments. - Abstract: Experimental Physics and Industrial Control System (EPICS) is a software tool that during last years has become relevant as a main framework to deploy distributed control systems in large scientific environments. At the moment, ESS Bilbao uses this middleware to perform the control of their Ion Source Hydrogen Positive (ISHP) project. The implementation of the control system was based on: PXI Real Time controllers using the LabVIEW-RT and LabVIEW-EPICS tools; and RIO devices based on Field-Programmable Gate Array (FPGA) technology. Intended to provide a full compliant EPICS IOCs for RIO devices and to avoid additional efforts on the system maintainability, a migration of the current system to a derivative Red Hat Linux (CentOS) environment has been conducted. This paper presents a real application case study for using the NIRIO EPICS device support (NIRIO-EDS) to give support to the ISHP. Although RIO FPGA configurations are particular solutions for ISHP performance, the NIRIO-EDS has permitted the control and monitoring of devices by applying a well-defined design methodology into the previous FPGA configuration for RIO/FlexRIO devices. This methodology has permitted a fast and easy deployment for the new robust, scalable and maintainable software to support RIO devices into the ISHP control architecture.

  10. Application study of EPICS-based redundant method for reactor control system

    International Nuclear Information System (INIS)

    Zhang Ning; Han Lifeng; Chen Yongzhong; Guo Bing; Yin Congcong

    2013-01-01

    In the reactor control system prototype development of TMSR (Thorium Molten Salt Reactor system, CAS) project, EPICS (Experimental Physics and Industrial Control System) is adopted as Instrument and Control software platform. For the aim of IOC (Input/Output Controller) redundancy and data synchronization of the system, the EPICS-based RMT (Redundancy Monitor Task ) software package and its data-synchronization component CCE (Continuous Control Executive) were introduced. By the development of related IOC driver, redundant switch-over control of server IOC was implemented. The method of redundancy implementation using RMT in server and redundancy performance test for power control system are discussed in this paper. (authors)

  11. EPICS Input/Output Controller (IOC) application developer's guide. APS Release 3.12

    International Nuclear Information System (INIS)

    Kraimer, M.R.

    1994-11-01

    This document describes the core software that resides in an Input/Output Controller (IOC), one of the major components of EPICS. The basic components are: (OPI) Operator Interface; this is a UNIX based workstation which can run various EPICS tools; (IOC) Input/Output Controller; this is a VME/VXI based chassis containing a Motorola 68xxx processor, various I/O modules, and VME modules that provide access to other I/O buses such as GPIB, (LAN), Local Area Network; and this is the communication network which allows the IOCs and OPIs to communicate. Epics provides a software component, Channel Access, which provides network transparent communication between a Channel Access client and an arbitrary number of Channel Access servers

  12. Configuration and application of He RFQ LLRF control system based on EPICS

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Tae-Sung; Jeong, Hae-Seong; Kim, Seong-Gu; Song, Young-Gi; Kim, Han-Sung; Seol, Kyung-Tae; Kwon, Hyeok-Jung; Cho, Yong-Sub [Korea Multipurpose Accelerator Complex, Gyeongju (Korea, Republic of)

    2015-10-15

    In He RFQ device, the high-power Radio-Frequency (RF) is very important because it is responsible for the stable delivery and efficient acceleration of the beam. Since that, the control system of high-power Radio-Frequency must be developed and this system is called LLRF control system. The LLRF control system required exquisite amplitude value that has ±1 % error range. We need a precise remote control system for this reason. This paper represents the configuration of LLRF control system in terms of software layers based on EPICS. Also, this paper explains the application of LLRF control system to test environment (hardware) and represents test result and suggests future work. The LLRF control system at the He RFQ is very important. The configuration of LLRF control system is completed on the software side and hardware modules: vxworks operating system installation, EPICS BASE compilation, module source code compiled, object file loading and execution on vxworks, EPICS IOC operation check, etc. The application of LLRF control system to module is implemented well: ADC module, DAC module, EPICS IOC test.

  13. EPICS device support module as ATCA system manager for the ITER fast plant system controller

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Paulo F., E-mail: pricardofc@ipfn.ist.utl.pt [Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico – Universidade Técnica de Lisboa, Lisboa (Portugal); Santos, Bruno; Gonçalves, Bruno; Carvalho, Bernardo B.; Sousa, Jorge; Rodrigues, A.P.; Batista, António J.N.; Correia, Miguel; Combo, Álvaro [Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico – Universidade Técnica de Lisboa, Lisboa (Portugal); Correia, Carlos M.B.A. [Centro de Instrumentação, Departamento de Física, Universidade de Coimbra, Coimbra (Portugal); Varandas, Carlos A.F. [Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico – Universidade Técnica de Lisboa, Lisboa (Portugal)

    2013-10-15

    Highlights: ► In Nuclear Fusion, demanding security and high-availability requirements call for redundancy to be available. ► ATCA based Nuclear Fusion Systems are composed by several electronic and mechanical component. ► Control and monitoring of ATCA electronic systems are recommended. ► ITER Fast Plant System Controller Project CODAC system prototype. ► EPICS device support module as External ATCA system manager solution. -- Abstract: This paper presents an Enhanced Physics and Industrial Control System (EPICS) device support module for the International Thermonuclear Experimental Reactor (ITER) Fast Plant System Controller (FPSC) project based in Advanced Telecommunications Computing Architecture (ATCA) specification. The developed EPICS device support module provides an External System Manager (ESM) solution for monitoring and control the ITER FPSC ATCA shelf system and data acquisition boards in order to take proper action and report problems to a control room operator or high level management unit in case of any system failure occurrence. EPICS device support module acts as a Channel Access (CA) server to report problems and publish ATCA system data information to the control room operator, high level management unit or other CA network clients such as Control System Studio Operator Interfaces (CSS OPIs), Best Ever Alarm System Toolkit (BEAST), Best Ever Archive Utility (BEAUTY) or other CA client applications. EPICS device support module communicates with the ATCA Shelf manager (ShM) using HTTP protocol to send and receive commands through POST method in order to get and set system and shelf components properties such as fan speeds measurements, temperatures readings, module status and ATCA boards acquisition and configuration parameters. All system properties, states, commands and parameters are available through the EPICS device support module CA server in EPICS Process Variables (PV) and signals format. ATCA ShM receives the HTTP protocol

  14. Implementation of EPICS based vacuum control system for variable energy cyclotron centre, Kolkata

    Science.gov (United States)

    Roy, Anindya; Bhole, R. B.; Nandy, Partha P.; Yadav, R. C.; Pal, Sarbajit; Roy, Amitava

    2015-03-01

    The vacuum system of the Room Temperature (K = 130) Cyclotron of Variable Energy Cyclotron Centre is comprised of vacuum systems of main machine and Beam Transport System. The vacuum control system is upgraded to a PLC based Automated system from the initial relay based Manual system. The supervisory control of the vacuum system is implemented in Experimental Physics and Industrial Control System (EPICS). An EPICS embedded ARM based vacuum gauge controller is developed to mitigate the requirement of vendor specific gauge controller for gauges and also for seamless integration of the gauge controllers with the control system. A set of MS-Windows ActiveX components with embedded EPICS Channel Access interface are developed to build operator interfaces with less complex programming and to incorporate typical Windows feature, e.g., user authentication, file handling, better fonts, colors, mouse actions etc. into the operator interfaces. The control parameters, monitoring parameters, and system interlocks of the system are archived in MySQL based EPICS MySQL Archiver developed indigenously. In this paper, we describe the architecture, the implementation details, and the performance of the system.

  15. Implementation of EPICS based vacuum control system for variable energy cyclotron centre, Kolkata

    Energy Technology Data Exchange (ETDEWEB)

    Roy, Anindya, E-mail: r-ani@vecc.gov.in; Bhole, R. B.; Nandy, Partha P.; Yadav, R. C.; Pal, Sarbajit; Roy, Amitava [Variable Energy Cyclotron Centre, 1/AF Bidhan Nagar, Kolkata 700064 (India)

    2015-03-15

    The vacuum system of the Room Temperature (K = 130) Cyclotron of Variable Energy Cyclotron Centre is comprised of vacuum systems of main machine and Beam Transport System. The vacuum control system is upgraded to a PLC based Automated system from the initial relay based Manual system. The supervisory control of the vacuum system is implemented in Experimental Physics and Industrial Control System (EPICS). An EPICS embedded ARM based vacuum gauge controller is developed to mitigate the requirement of vendor specific gauge controller for gauges and also for seamless integration of the gauge controllers with the control system. A set of MS-Windows ActiveX components with embedded EPICS Channel Access interface are developed to build operator interfaces with less complex programming and to incorporate typical Windows feature, e.g., user authentication, file handling, better fonts, colors, mouse actions etc. into the operator interfaces. The control parameters, monitoring parameters, and system interlocks of the system are archived in MySQL based EPICS MySQL Archiver developed indigenously. In this paper, we describe the architecture, the implementation details, and the performance of the system.

  16. Implementation of EPICS based vacuum control system for variable energy cyclotron centre, Kolkata

    International Nuclear Information System (INIS)

    Roy, Anindya; Bhole, R. B.; Nandy, Partha P.; Yadav, R. C.; Pal, Sarbajit; Roy, Amitava

    2015-01-01

    The vacuum system of the Room Temperature (K = 130) Cyclotron of Variable Energy Cyclotron Centre is comprised of vacuum systems of main machine and Beam Transport System. The vacuum control system is upgraded to a PLC based Automated system from the initial relay based Manual system. The supervisory control of the vacuum system is implemented in Experimental Physics and Industrial Control System (EPICS). An EPICS embedded ARM based vacuum gauge controller is developed to mitigate the requirement of vendor specific gauge controller for gauges and also for seamless integration of the gauge controllers with the control system. A set of MS-Windows ActiveX components with embedded EPICS Channel Access interface are developed to build operator interfaces with less complex programming and to incorporate typical Windows feature, e.g., user authentication, file handling, better fonts, colors, mouse actions etc. into the operator interfaces. The control parameters, monitoring parameters, and system interlocks of the system are archived in MySQL based EPICS MySQL Archiver developed indigenously. In this paper, we describe the architecture, the implementation details, and the performance of the system

  17. Multipurpose Controller with EPICS integration and data logging: BPM application for ESS Bilbao

    International Nuclear Information System (INIS)

    Arredondo, I.; Campo, M. del; Echevarria, P.; Jugo, J.; Etxebarria, V.

    2013-01-01

    This work presents a multipurpose configurable control system which can be integrated in an EPICS control network, this functionality being configured through a XML configuration file. The core of the system is the so-called Hardware Controller which is in charge of the control hardware management, the set up and communication with the EPICS network and the data storage. The reconfigurable nature of the controller is based on a single XML file, allowing any final user to easily modify and adjust the control system to any specific requirement. The selected Java development environment ensures a multiplatform operation and large versatility, even regarding the control hardware to be controlled. Specifically, this paper, focused on fast control based on a high performance FPGA, describes also an application approach for the ESS Bilbao's Beam Position Monitoring system. The implementation of the XML configuration file and the satisfactory performance outcome achieved are presented, as well as a general description of the Multipurpose Controller itself

  18. Performance Comparison of EPICS IOC and MARTe in a Hard Real-Time Control Application

    Science.gov (United States)

    Barbalace, Antonio; Manduchi, Gabriele; Neto, A.; De Tommasi, G.; Sartori, F.; Valcarcel, D. F.

    2011-12-01

    EPICS is used worldwide mostly for controlling accelerators and large experimental physics facilities. Although EPICS is well fit for the design and development of automation systems, which are typically VME or PLC-based systems, and for soft real-time systems, it may present several drawbacks when used to develop hard real-time systems/applications especially when general purpose operating systems as plain Linux are chosen. This is in particular true in fusion research devices typically employing several hard real-time systems, such as the magnetic control systems, that may require strict determinism, and high performance in terms of jitter and latency. Serious deterioration of important plasma parameters may happen otherwise, possibly leading to an abrupt termination of the plasma discharge. The MARTe framework has been recently developed to fulfill the demanding requirements for such real-time systems that are alike to run on general purpose operating systems, possibly integrated with the low-latency real-time preemption patches. MARTe has been adopted to develop a number of real-time systems in different Tokamaks. In this paper, we first summarize differences and similarities between EPICS IOC and MARTe. Then we report on a set of performance measurements executed on an x86 64 bit multicore machine running Linux with an IO control algorithm implemented in an EPICS IOC and in MARTe.

  19. Sources of pre-analytical variations in yield of DNA extracted from blood samples: analysis of 50,000 DNA samples in EPIC.

    Directory of Open Access Journals (Sweden)

    Elodie Caboux

    Full Text Available The European Prospective Investigation into Cancer and nutrition (EPIC is a long-term, multi-centric prospective study in Europe investigating the relationships between cancer and nutrition. This study has served as a basis for a number of Genome-Wide Association Studies (GWAS and other types of genetic analyses. Over a period of 5 years, 52,256 EPIC DNA samples have been extracted using an automated DNA extraction platform. Here we have evaluated the pre-analytical factors affecting DNA yield, including anthropometric, epidemiological and technical factors such as center of subject recruitment, age, gender, body-mass index, disease case or control status, tobacco consumption, number of aliquots of buffy coat used for DNA extraction, extraction machine or procedure, DNA quantification method, degree of haemolysis and variations in the timing of sample processing. We show that the largest significant variations in DNA yield were observed with degree of haemolysis and with center of subject recruitment. Age, gender, body-mass index, cancer case or control status and tobacco consumption also significantly impacted DNA yield. Feedback from laboratories which have analyzed DNA with different SNP genotyping technologies demonstrate that the vast majority of samples (approximately 88% performed adequately in different types of assays. To our knowledge this study is the largest to date to evaluate the sources of pre-analytical variations in DNA extracted from peripheral leucocytes. The results provide a strong evidence-based rationale for standardized recommendations on blood collection and processing protocols for large-scale genetic studies.

  20. EPICS based DAQ system

    International Nuclear Information System (INIS)

    Cheng Weixing; Chen Yongzhong; Zhou Weimin; Ye Kairong; Liu Dekang

    2002-01-01

    EPICS is the most popular developing platform to build control system and beam diagnostic system in modern physics experiment facilities. An EPICS based data acquisition system was built in Redhat 6.2 operation system. The system is successfully used in the beam position monitor mapping, it improves the mapping process a lot

  1. EPICS architecture

    International Nuclear Information System (INIS)

    Dalesio, L.R.; Kozubal, A.J.; Kraimer, M.R.

    1992-01-01

    The Experimental Physics and Industrial Control System (EPICS) provides control and data acquisition for the experimental physics community. Because the capabilities required by the experimental physics community for control were not available through industry, we began the design and implementation of EPICS. It is a distributed process control system built on a software communication bus. The functional subsystems, which provide data acquisition, supervisory control, closed loop control, archiving, and alarm management, greatly reduce the need for programming. Sequential control is provided through a sequential control language, allowing the implementer to express state diagrams easily. Data analysis of the archived data is provided through an interactive tool. The timing system provides distributed synchronization for control and time stamped data for data correlation across nodes in the network. The system is scalable from a single test station with a low channel count to a large distributed network with thousands of channels. The functions provided to the physics applications have proven helpful to the experiments while greatly reducing the time to deliver controls. (author)

  2. EPICS Application Based on RTEMS

    International Nuclear Information System (INIS)

    Shi Haoli; Wang Chunhong; Tang Jingyu

    2009-01-01

    At present, in the accelerator field all over the world, the control system is established with EPICS, which is a configuration software package based on Ethernet and distributed control system. Early version of EPICS was developed based on VxWorks. Now, EPICS international collaboration group is dedicating to supporting open source, free RTEMS, and extending RTEMS into the newer version of EPICS3.14. The paper illustrates the development, characteristic of RTEMS, compares the performances of several ordinary RTOS, builds RTEMS operating system based on MVME5500, and finally presents an EPICS application example on RTEMS. (authors)

  3. Multipurpose Controller with EPICS integration and data logging: BPM application for ESS Bilbao

    Energy Technology Data Exchange (ETDEWEB)

    Arredondo, I., E-mail: iarredondo@essbilbao.org [ESS Bilbao, Edificio Cosimet Paseode Landabarri 2, 48940 Leioa, Bizkaia (Spain); Campo, M. del; Echevarria, P. [ESS Bilbao, Edificio Cosimet Paseode Landabarri 2, 48940 Leioa, Bizkaia (Spain); Jugo, J.; Etxebarria, V. [University of Basque Country (UPV/EHU), Department of Electricity and Electronics, Science and Technology Fac., Barrio Sarriena s/n, 48940 Leioa, Bizkaia (Spain)

    2013-10-21

    This work presents a multipurpose configurable control system which can be integrated in an EPICS control network, this functionality being configured through a XML configuration file. The core of the system is the so-called Hardware Controller which is in charge of the control hardware management, the set up and communication with the EPICS network and the data storage. The reconfigurable nature of the controller is based on a single XML file, allowing any final user to easily modify and adjust the control system to any specific requirement. The selected Java development environment ensures a multiplatform operation and large versatility, even regarding the control hardware to be controlled. Specifically, this paper, focused on fast control based on a high performance FPGA, describes also an application approach for the ESS Bilbao's Beam Position Monitoring system. The implementation of the XML configuration file and the satisfactory performance outcome achieved are presented, as well as a general description of the Multipurpose Controller itself.

  4. EPICS system: an overview

    International Nuclear Information System (INIS)

    Bartlett, J.F.; Bobbitt, J.S.; Kramper, B.J.; Lahey, T.E.; MacKinnon, B.A.; West, R.E.

    1984-02-01

    This paper presents an overview of the EPICS control system at FERMILAB. EPICS is a distributed, multi-user, interactive system for the control and monitoring of particle beamlines at a high-energy experimental physics laboratory. The overview discusses the operating environment of the control system, the requirements which determined the design decisions, the hardware and software configurations, and plans for the future growth and enhancement of the present system. This paper is the first of three related papers on the EPICS system. The other two cover (1) the system structure and user interface and (2) RSX implementation issues

  5. Association among individual deprivation, glycemic control, and diabetes complications: the EPICES score.

    Science.gov (United States)

    Bihan, Hélène; Laurent, Silvana; Sass, Catherine; Nguyen, Gérard; Huot, Caroline; Moulin, Jean Jacques; Guegen, René; Le Toumelin, Philippe; Le Clésiau, Hervé; La Rosa, Emilio; Reach, Gérard; Cohen, Régis

    2005-11-01

    Previous studies have related poor glycemic control and/or some diabetes complications to low socioeconomic status. Some aspects of socioeconomic status have not been assessed in these studies. In the present study, we used an individual index of deprivation, the Evaluation de la Précarité et des Inégalités de santé dans les Centres d'Examens de Santé (Evaluation of Precarity and Inequalities in Health Examination Centers [EPICES]) score, to determine the relationship among glycemic control, diabetes complications, and individual conditions of deprivation. We conducted a cross-sectional prevalence study in 135 consecutive diabetic patients (age 59.41 +/- 13.2 years [mean +/- SD]) admitted in the hospitalization unit of a French endocrine department. Individual deprivation was assessed by the EPICES score, calculated from 11 socioeconomic questions. Glycemic control, lipid levels, blood pressure, retinopathy, neuropathy, and nephropathy were assessed. HbA(1c) level was significantly correlated with the EPICES score (r = 0.366, P < 0.001). The more deprived patients were more likely than the less deprived patients to have poor glycemic control (beta = 1.984 [SE 0.477], P < 0.001), neuropathy (odds ratio 2.39 [95% CI 1.05-5.43], P = 0.037), retinopathy (3.66 [1.39-9.64], P = 0.009), and being less often admitted for 1-day hospitalization (0.32 [0.14-0.74], P = 0.008). No significant relationship was observed with either nephropathy or cardiovascular risk factors. Deprivation status is associated with poor metabolic control and more frequent microvascular complications, i.e., retinopathy and neuropathy. The medical and economic burden of deprived patients is high.

  6. The EPICS-based remote control system for muon beam line devices at J-PARC MUSE

    Science.gov (United States)

    Ito, T. U.; Nakahara, K.; Kawase, M.; Fujimori, H.; Kobayashi, Y.; Higemoto, W.; Miyake, Y.

    2010-04-01

    The remote control system for muon beam line devices of J-PARC MUSE has been developed with the Experimental Physics and Industrial Control System (EPICS). The EPICS input/output controller was installed in standard Linux PCs for slow control of the devices. Power supplies for 21 magnetic elements and four slit controllers for the decay-surface muon beam line in the Materials and Life Science Experimental Facility are now accessible via Ethernet from a graphical user interface which has been composed using the Motif Editor and Display Manger.

  7. Development of EPICS Input Output Controller and User Interface for the PEFP Low Level RF Control System

    Energy Technology Data Exchange (ETDEWEB)

    Song, Young Gi; Kim, Han Sung; Seol, Kyung Tae; Kwon, Hyeok Jung; Cho, Yong Sub [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2010-05-15

    The Low-Level RF (LLRF) control system of the Proton Engineering Frontier Project (PEFP) was developed for handling the driving frequency for Quadrupole (RFQ) and the Draft Tube Linac (DTL) cavities in 2006. The RF amplitude and phase of the accelerating field were controlled within 1% and 1 degree by stability requirements, respectively. Operators have been using the LLRF control system under the windows based text console mode as an operator interface. The LLRF control system could not be integrated with Experimental Physics Industrial Control System (EPICS) Input Output Controllers (IOC) for each subsection of PEFP facility. The main objective of this study is to supply operators of the LLRF control system with user friendly and convenient operating environment. The new LLRF control system is composed of a Verse Module Eurocard (VME) baseboard, a PCI Mezzanine Card (PMC), Board Support Package (BSP), EPICS software tool and a Real-Time Operating System (RTOS) VxWorks. A test with a dummy cavity of the new LLRF control system shows that operators can control and monitor operation parameters for a desired feedback action by using EPICS Channel Access (CA).

  8. Development of EPICS Input Output Controller and User Interface for the PEFP Low Level RF Control System

    International Nuclear Information System (INIS)

    Song, Young Gi; Kim, Han Sung; Seol, Kyung Tae; Kwon, Hyeok Jung; Cho, Yong Sub

    2010-01-01

    The Low-Level RF (LLRF) control system of the Proton Engineering Frontier Project (PEFP) was developed for handling the driving frequency for Quadrupole (RFQ) and the Draft Tube Linac (DTL) cavities in 2006. The RF amplitude and phase of the accelerating field were controlled within 1% and 1 degree by stability requirements, respectively. Operators have been using the LLRF control system under the windows based text console mode as an operator interface. The LLRF control system could not be integrated with Experimental Physics Industrial Control System (EPICS) Input Output Controllers (IOC) for each subsection of PEFP facility. The main objective of this study is to supply operators of the LLRF control system with user friendly and convenient operating environment. The new LLRF control system is composed of a Verse Module Eurocard (VME) baseboard, a PCI Mezzanine Card (PMC), Board Support Package (BSP), EPICS software tool and a Real-Time Operating System (RTOS) VxWorks. A test with a dummy cavity of the new LLRF control system shows that operators can control and monitor operation parameters for a desired feedback action by using EPICS Channel Access (CA).

  9. Design and configuration of VME EPICS driver for He RFQ LLRF control system

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Tae-Sung; Jeong, Hae-Seong; Kim, Seong-Gu; Song, Young-Gi; Kim, Han-Sung; Seol, Kyung-Tae; Kwon, Hyeok-Jung; Cho, Yong-Sub [KOMAC, Gyeongju (Korea, Republic of)

    2015-05-15

    In Helium Radio-Frequency Quadrupole (He RFQ) development, the role of the high-power Radio-Frequency (RF) is very important because it is responsible for stable delivery and efficient acceleration of the beam. Since the amplitude control requirements of LLRF system are ±1 % (amplitude), we need a precise remote control system for this reason. This system is referred to as Low-Level RF (LLRF) control system. This paper describes the basic configuration tasks performed by hardware side and the software side to build the LLRF control system, and describes the future work of the He RFQ LLRF control system based on this paper. LLRF control system development at the He RFQ development stage is important. LLRF control system development requires the exact configuration of hardware and software. For each of the Layer configuration is completed on the software side and hardware modules: vxworks operating system installation, EPICS BASE compilation, module source code compiled, object file loading and execution on vxworks, EPICS IOC operation check, etc.

  10. Soft real-time EPICS extensions for fast control: A case study applied to a TCV equilibrium algorithm

    International Nuclear Information System (INIS)

    Castro, R.; Romero, J.A.; Vega, J.; Nieto, J.; Ruiz, M.; Sanz, D.; Barrera, E.; De Arcas, G.

    2014-01-01

    Highlights: • Implementation of a soft real-time control system based on EPICS technology. • High data throughput system control implementation. • GPU technology applied to fast control. • EPICS fast control based solution. • Fast control and data acquisition in Linux. - Abstract: For new control systems development, ITER distributes CODAC Core System that is a software package based on Linux RedHat, and includes EPICS (Experimental Physics and Industrial Control System) as software control system solution. EPICS technology is being widely used for implementing control systems in research experiments and it is a very well tested technology, but presents important lacks to meet fast control requirements. To manage and process massive amounts of acquired data, EPICS requires additional functions such as: data block oriented transmissions, links with speed-optimized data buffers and synchronization mechanisms not based on system interruptions. This EPICS limitation turned out clearly during the development of the Fast Plant System Controller Prototype for ITER based on PXIe platform. In this work, we present a solution that, on the one hand, is completely compatible and based on EPCIS technology, and on the other hand, extends EPICS technology for implementing high performance fast control systems with soft-real time characteristics. This development includes components such as: data acquisition, processing, monitoring, data archiving, and data streaming (via network and shared memory). Additionally, it is important to remark that this system is compatible with multiple Graphics Processing Units (GPUs) and is able to integrate MatLab code through MatLab engine connections. It preserves EPICS modularity, enabling system modification or extension with a simple change of configuration, and finally it enables parallelization based on data distribution to different processing components. With the objective of illustrating the presented solution in an actual

  11. EPICS based low-level radio frequency control system in LIPAc

    Energy Technology Data Exchange (ETDEWEB)

    Calvo, Julio, E-mail: julio.calvo@ciemat.es [Centro de Investigaciones Energeticas Medioambientales y Tecnologicas, Ciemat (Spain); Rivers, Mark L. [Department of Geophysical Sciences and Center for Advanced Radiation Sources, The University of Chicago (United States); Patricio, Miguel A. [Departamento de Informatica, Universidad Carlos III de Madrid (Spain); Ibarra, Angel [Centro de Investigaciones Energeticas Medioambientales y Tecnologicas, Ciemat (Spain)

    2012-11-15

    Highlights: Black-Right-Pointing-Pointer The system proposed can control amplitude and phase of each cavity. Black-Right-Pointing-Pointer Rapid diagnostics are refreshed in milliseconds. Black-Right-Pointing-Pointer Increasing control parameters will not increase consumed time neither complexity. Black-Right-Pointing-Pointer IQ demodulation can be achieved thanks to the transformed values at driver level. - Abstract: The IFMIF-EVEDA (International Fusion Materials Irradiation Facility - Engineering Validation and Engineering Design Activity) linear accelerator, known as Linear IFMIF Prototype Accelerator (LIPAc), will be a 9 MeV, 125 mA continuous wave (CW) deuteron accelerator prototype to validate the technical options of the accelerator design for IFMIF. The primary mission of such facility is to test and verify materials performance when subjected to extensive neutron irradiation of the type encountered in a fusion reactor to prepare for the design, construction, licensing and safe operation of a fusion demonstration reactor (DEMO). The radio frequency (RF) power system of IFMIF-EVEDA consists of 18 RF chains working at 175 MHz with three amplification stages each. The low-level radio frequency (LLRF) controls the amplitude and phase of the signal to be synchronized with the beam and it also controls the resonance frequency of the cavities. The system is based on a commercial compact peripheral component interconnect (cPCI) field programmable gate array (FPGA) board, provided by Lyrtech and controlled by a Windows host PC. For this purpose, it is mandatory to communicate the cPCI FPGA board from EPICS Channel Access [1]. A software architecture on EPICS framework in order to control and monitor the LLRF system is presented.

  12. EPICS system: system structure and user interface

    International Nuclear Information System (INIS)

    West, R.E.; Bartlett, J.F.; Bobbitt, J.S.; Lahey, T.E.; Kramper, B.J.; MacKinnon, B.A.

    1984-02-01

    This paper present the user's view of and the general organization of the EPICS control system at Fermilab. Various subsystems of the EPICS control system are discussed. These include the user command language, software protection, the device database, remote computer interfaces, and several application utilities. This paper is related to two other papers on EPICS: an overview paper and a detailed implementation paper

  13. Versatile Data Acquisition and Controls for EPICS using VME-based FPGAs

    International Nuclear Information System (INIS)

    Trent Allison; Roger Flood

    2001-01-01

    Field Programmable Gate Arrays (FPGAs) have provided versatile VME based data acquisition and control systems with minimal development times for the Thomas Jefferson National Accelerator Facility (Jefferson Lab). FPGAs have been used to interface with VME controllers using both standard A16 and A24 address modes. VME vector-interrupt capability has also been implemented for timing issues in some applications. FPGA designs have additionally been used to provide controls for various systems by interfacing with Analog to Digital Converters (DAC), interlocks, and other drive signals. These controls can be molded to the individual needs of each system and can provide operators with indicators and controls in EPICS via a VME interface. This allows the developer to choose components and make specifications that are not available commercially. Jefferson Lab has begun developing standard FPGA libraries that result in quick turnaround times and inexpensive designs. There have been approximately eight VME based FPGA designs implanted in one department at Jefferson Lab and they are becoming more widespread. FPGAs continue to become larger and faster enabling systems to be incorporated on one integrated circuit. Inherently, FPGAs can process data faster than many microprocessors due to the small processing overhead associated with a custom FPGA design. The ability to modify FPGA code enables the developer to easily implement future additions to a system, making the design flexible and expandable. This work supported by the U.S. DOE Contract No. DE-AC05-84ER40150

  14. EPICS V4 in Python

    International Nuclear Information System (INIS)

    Guobao Shen; Kraimer, M.; Davidsaver, M.

    2012-01-01

    At NSLS-II, Python has been selected as the primary development language for physics applications. Interest in Python as a rapid application development environment continues to grow. Many large experimental scientific facilities have adopted Python for beam commissioning and the operation. The EPICS control system framework has become the de facto standard for the control of large experimental facilities, where it is in use in over 100 facilities. The next version of EPICS (EPICS V4), under active development will extend the support for physics applications, data acquisition, and data analysis. Python support for EPICS V4 will provide an effective framework to address these requirements. This paper presents design, development and status of activities focused on EPICS V4 in Python

  15. GDA and EPICS: working in unison for science driven data acquisition and control at Diamond light source

    International Nuclear Information System (INIS)

    Gibbons, E.P.; Heron, M.T.; Rees, N.P.

    2012-01-01

    Diamond Light Source has recently received funding for an additional 10 photon beamlines, bringing the total to 32 beamlines and around 40 end-stations. These all use EPICS (Experimental Physics and Industrial Control System) for the control of the underlying instrumentation associated with photon delivery, the experiment and most of the data acquisition hardware. For the scientific users Diamond has developed the Generic Data Acquisition (GDA) application framework to provide a consistent science interface across all beamlines. While each application is customized to the science of its beamline, all applications are built from the framework and predominantly interface to the underlying instrumentation through the EPICS abstraction. We will describe the complete system, illustrate how it can be configured for a specific beamline application, and how other synchrotrons are, and can, adapt these tools for their needs. (authors)

  16. An EPICS IOC builder

    International Nuclear Information System (INIS)

    Abbott, M.G.; Cobb, T.

    2012-01-01

    An EPICS IOC (Input/Output Controller) is typically assembled from a number of standard components each with potentially quite complex hardware or software initialization procedures intermixed with a good deal of repetitive boiler-plate code. Assembling and maintaining a complex IOC can be a quite difficult and error prone process, particularly if the components are unfamiliar. The EPICS IOC builder is a Python library designed to automate the assembly of a complete IOC from a concise component level description. The dependencies and interactions between components as well as their detailed initialization procedures are automatically managed by the IOC builder through component description files maintained with the individual components. At Diamond Light Source we have a large library of components that can be assembled into EPICS IOCs. The IOC Builder is further finding increasing use in helping non-expert users to assemble an IOC without specialist knowledge. (authors)

  17. EPICS system: RSX implementation issues

    International Nuclear Information System (INIS)

    Lahey, T.E.; Bartlett, J.F.; Bobbitt, J.S.; Kramper, B.J.; MacKinnon, B.A.; West, R.E.

    1984-02-01

    This paper presents implementation details of the Experimental Physics Interactive Control System (EPICS). EPICS is used to control accelerated particle beams for high-energy physics experiments at the Fermi National Accelerator Laboratory. The topics discussed are: interprocessor communication, support of beamline terminals and devices, resource management, mapping, various problems, some solutions to the problems, performance measurement, and modifications and extensions to RSX-11M. This paper is the third of three related papers on the EPICS system. The other two cover (1) the system overview and (2) the system structure and user interface

  18. J-TEXT-EPICS: An EPICS toolkit attempted to improve productivity

    International Nuclear Information System (INIS)

    Zheng, Wei; Zhang, Ming; Zhang, Jing; Zhuang, Ge

    2013-01-01

    Highlights: • Tokamak control applications can be developed in very short period with J-TEXT-EPICS. • J-TEXT-EPICS enables users to build control applications with device-oriented functions. • J-TEXT-EPICS is fully compatible with EPICS Channel Access protocol. • J-TEXT-EPICS can be easily extended by plug-ins and drivers. -- Abstract: The Joint Texas Experimental Tokamak (J-TEXT) team has developed a new software toolkit for building Experimental Physics and Industrial Control System (EPICS) control applications called J-TEXT-EPICS. It aims to improve the development efficiency of control applications. With device-oriented features, it can be used to set or obtain the configuration or status of a device as well as invoke methods on a device. With its modularized design, its functions can be easily extended. J-TEXT-EPICS is completely compatible with the original EPICS Channel Access protocol and can be integrated into existing EPICS control systems smoothly. It is fully implemented in C number sign, thus it will benefit from abundant resources in.NET Framework. The J-TEXT control system is build with this toolkit. This paper presents the design and implementation of J-TEXT EPICS as well as its application in the J-TEXT control system

  19. Safety control system and its interface to EPICS for the off-line front end of the SPES project

    International Nuclear Information System (INIS)

    Vasquez, J.; Andrighetto, A.; Bassato, G.; Costa, L.; Giacchini, M.; Bertocco, M.

    2012-01-01

    The SPES (Selective Production of Exotic Species) project is based on a facility for the production of neutron-rich radioactive ion beams using the isotope separation on-line technique. The SPES off-line front-end apparatus involves a number of subsystems and procedures that are potentially dangerous both for human operators and for the equipment. The high voltage power supply, the ion source complex power supplies, the target chamber handling systems and the laser source are some example of these subsystems. For that reason, a safety control system has been developed. It is based on Schneider Electrics Preventa family safety modules that control the power supply of critical subsystems in combination with safety detectors that monitor critical variables. A Programmable Logic Controller (PLC), model BMXP342020 from the Schneider Electrics Modicon M340 family, is used for monitoring the status of the system as well as controlling the sequence of some operations in automatic way. A touch screen, model XBTGT5330 from the Schneider Electrics Magelis family, is used as Human Machine Interface (HMI) and communicates with the PLC using MODBUS-TCP. Additionally, an interface to the EPICS control network was developed using a home-made MODBUS-TCP EPICS driver in order to integrate it to the control system of the Front End as well as present the status of the system to the users on the main control panel. (authors)

  20. EPICS release 3.11 specific documentation -- EPICS release notes for 3.11

    International Nuclear Information System (INIS)

    1994-01-01

    EPICS release 3.11 is now ready for user testing. A person who wants to set up a simplified application environment to boot an IOC and create databases using R3.11 should follow the directions in Appendix B, page 27, of the EPICS Source/Release Control Manual, Sept. 20, 1993. The R3.11 EPICS path at ANL/APS is /net/phebos/epics/R3.11 so the command to get the new release is /net/phebos/epics/R3.11/Unix/share/bin/getrel /net/phebos/epics/R3.11. An existing R3.8 short form report can be copied to this new directory and used to create a database. ANL/APS is currently testing an Application Developers Source/Release control system. It is not yet ready for general distribution. Attached are the EPICS R3.11 release notes

  1. Study on managing EPICS database using ORACLE

    International Nuclear Information System (INIS)

    Liu Shu; Wang Chunhong; Zhao Jijiu

    2007-01-01

    EPICS is used as a development toolkit of BEPCII control system. The core of EPICS is a distributed database residing in front-end machines. The distributed database is usually created by tools such as VDCT and text editor in the host, then loaded to front-end target IOCs through the network. In BEPCII control system there are about 20,000 signals, which are distributed in more than 20 IOCs. All the databases are developed by device control engineers using VDCT or text editor. There's no uniform tools providing transparent management. The paper firstly presents the current status on EPICS database management issues in many labs. Secondly, it studies EPICS database and the interface between ORACLE and EPICS database. finally, it introduces the software development and application is BEPCII control system. (authors)

  2. Development and implementation of an EPICS-based accelerator control interface and automated beam optimisation at the S-DALINAC; Entwicklung und Implementierung einer EPICS-basierten Beschleuniger-Steuerungsschnittstelle und automatisierten Strahloptimierung am S-DALINAC

    Energy Technology Data Exchange (ETDEWEB)

    Schoesser, Thomas

    2017-06-12

    This thesis is divided into two parts of improvements to the accelerator control system of the S-DALINAC. In the first part the finalisation of the EPICS migration to the S-DALINAC control system is presented. Therefore the input-outputcontrollers(IOCs) of the controls of magnets, the targets, and the video multiplexer are included into the EPICS framework. In addition to that the operator interfaces(OPIs) of the controls of magnets and targets are implemented. To configure these IOCs and OPIs a relational database is used, which was extended within this thesis. In- and output of magnet control is provided by rotating knobs and touch screens, which hardware were modernised. The realised steps are doing their part in reducing perturbations and ease up operations since. The second part covers the automated optimisation of beam optics. Therefore the software AreaDetector was integrated into the S-DALINAC control system. The functionality is shown by the example of setting a quadrupol magnet deflection-free fully automated. Also the flexibility enables other setups to be automatically optimised in the future.

  3. Are metabolic signatures mediating the relationship between lifestyle factors and hepatocellular carcinoma risk? Results from a nested case-control study in EPIC.

    NARCIS (Netherlands)

    Assi, Nada; Thomas, Duncan C; Leitzman, Michael; Stepien, Magdalena; Chajes, Veronique; Philip, Thierry; Vineis, Paolo; Bamia, Christina; Boutron-Ruault, Marie-Christine; Sandanger, Torkjel M; Molinuevo, Amaia; Boshuizen, Hendriek C; Sundkvist, Anneli; Kühn, Tilman; Travis, Ruth C; Overvad, Kim; Riboli, Elio; Gunter, Marc J; Scalbert, Augustin; Jenab, Mazda; Ferrari, Pietro; Viallon, Vivian

    2018-01-01

    The "meeting-in-the-middle" (MITM) is a principle to identify exposure biomarkers that are also predictors of disease. The MITM statistical framework was applied in a nested case-control study of hepatocellular carcinoma (HCC) within EPIC where healthy lifestyle index (HLI) variables were related to

  4. Integrating commercial and legacy systems with EPICS

    International Nuclear Information System (INIS)

    Hill, J.O.; Kasemir, K.U.

    1997-01-01

    The Experimental Physics and Industrial Control System (EPICS) is a software toolkit, developed by a worldwide collaboration, which significantly reduces the level of effort required to implement a new control system. Recent developments now also significantly reduce the level of effort required to integrate commercial, legacy and/or site-authored control systems with EPICS. This paper will illustrate with an example both the level and type of effort required to use EPICS with other control system components as well as the benefits that may arise

  5. Experience using EPICS on PC platforms

    International Nuclear Information System (INIS)

    Hill, J.O.; Kasemire, K.U.

    1997-03-01

    The Experimental Physics and Industrial Control System (EPICS) has been widely adopted in the accelerator community. Although EPICS is available on many platforms, the majority of implementations have used UNIX workstations as clients, and VME- or VXI-based processors for distributed input output controllers. Recently, a significant portion of EPICS has been ported to personal computer (PC) hardware platforms running Microsoft's operating systems, and also Wind River System's real time vxWorks operating system. This development should significantly reduce the cost of deploying EPICS systems, and the prospect of using EPICS together with the many high quality commercial components available for PC platforms is also encouraging. A hybrid system using both PC and traditional platforms is currently being implemented at LANL for LEDA, the low energy demonstration accelerator under construction as part of the Accelerator Production of Tritium (APT) project. To illustrate these developments the authors compare their recent experience deploying a PC-based EPICS system with experience deploying similar systems based on traditional (UNIX-hosted) EPICS hardware and software platforms

  6. Reliability of Serum Metabolites over a Two-Year Period: A Targeted Metabolomic Approach in Fasting and Non-Fasting Samples from EPIC

    Science.gov (United States)

    Achaintre, David; Sacerdote, Carlotta; Vineis, Paolo; Key, Timothy J.; Onland Moret, N. Charlotte; Scalbert, Augustin; Rinaldi, Sabina; Ferrari, Pietro

    2015-01-01

    Objective Although metabolic profiles have been associated with chronic disease risk, lack of temporal stability of metabolite levels could limit their use in epidemiological investigations. The present study aims to evaluate the reliability over a two-year period of 158 metabolites and compare reliability over time in fasting and non-fasting serum samples. Methods Metabolites were measured with the AbsolueIDQp180 kit (Biocrates, Innsbruck, Austria) by mass spectrometry and included acylcarnitines, amino acids, biogenic amines, hexoses, phosphatidylcholines and sphingomyelins. Measurements were performed on repeat serum samples collected two years apart in 27 fasting men from Turin, Italy, and 39 non-fasting women from Utrecht, The Netherlands, all participating in the European Prospective Investigation into Cancer and Nutrition (EPIC) study. Reproducibility was assessed by estimating intraclass correlation coefficients (ICCs) in multivariable mixed models. Results In fasting samples, a median ICC of 0.70 was observed. ICC values were fasting samples, the median ICC was 0.54. ICC values were fasting as compared to fasting samples, with a statistically significant difference for 19–36% of acylcarnitines, phosphatidylcholines and sphingomyelins. Conclusion A single measurement per individual may be sufficient for the study of 73% and 52% of the metabolites showing ICCs >0.50 in fasting and non-fasting samples, respectively. ICCs were higher in fasting samples that are preferable to non-fasting. PMID:26274920

  7. Three Object-Oriented enhancement for EPICS

    Science.gov (United States)

    Osberg, E. A.; Dohan, D. A.; Richter, R.; Biggs, R.; Chillara, K.; Wade, D.; Bossom, J.

    1994-12-01

    In line with our group's intention of producing software using, where possible, Object-Oriented methodologies and techniques in the development of RF control systems, we have undertaken three projects to enhance the EPICS software environment. Two of the projects involve interfaces to EPICs Channel Access from Object-Oriented languages. The third is an enhancement to the EPICS State Notation Language to better support the Shlaer-Mellor Object-Oriented Analysis and Design Methodology. This paper discusses the motivation, approaches, results and future directions of these three projects.

  8. EPICS channel access using websocket

    International Nuclear Information System (INIS)

    Uchiyama, A.; Furukawa, K.; Higurashi, Y.

    2012-01-01

    Web technology is useful as a means of widely disseminating accelerator and beam status information. For this purpose, WebOPI was implemented by SNS as a web-based system using Ajax (asynchronous JavaScript and XML) with EPICS. On the other hand, it is often necessary to control the accelerator from different locations as well as the central control room during beam operation and maintenance. However, it is not realistic to replace the GUI-based operator interface (OPI) with a Web-based system using Ajax technology because of interactive performance issue. Therefore, as a next generation OPI over the web using EPICS Channel Access (CA), we developed a client system based on WebSocket, which is a new protocol provided by the Internet Engineering Task Force (IETF) for Web-based systems. WebSocket is a web technology that provides bidirectional, full-duplex communication channels over a single TCP connection. By utilizing Node.js and the WebSocket access library called Socket.IO, a WebSocket server was implemented. Node.js is a server-side JavaScript language built on the Google V8 JavaScript Engine. In order to construct the WebSocket server as an EPICS CA client, an add-on for Node.js was developed in C/C++ using the EPICS CA library, which is included in the EPICS base. As a result, for accelerator operation, Web-based client systems became available not only in the central control room but also with various types of equipment. (author)

  9. Web services interface to EPICS channel access

    Institute of Scientific and Technical Information of China (English)

    DUAN Lei; SHEN Liren

    2008-01-01

    Web services is used in Experimental Physics and Industrial Control System (EPICS). Combined with EPICS Channel Access protocol, Web services' high usability, platform independence and language independence can be used to design a fully transparent and uniform software interface layer, which helps us complete channel data acquisition, modification and monitoring functions. This software interface layer, a cross-platform of cross-language,has good interopcrability and reusability.

  10. Web services interface to EPICS channel access

    International Nuclear Information System (INIS)

    Duan Lei; Shen Liren

    2008-01-01

    Web services is used in Experimental Physics and Industrial Control System (EPICS). Combined with EPICS Channel Access protocol, Web services high usability, platform independence and language independence can be used to design a fully transparent and uniform software interface layer, which helps us complete channel data acquisition, modification and monitoring functions. This software interface layer, a cross-platform of cross-language, has good interoperability and reusability. (authors)

  11. Development of EPICS IOC for TPLC-32 platform

    International Nuclear Information System (INIS)

    Jain, Sanjay Kumar; Bhamra, Ratna; Kavalan, P.K.; Vaidya, U.W.

    2014-01-01

    Experimental Physics and Industrial Control System (EPICS) SCADA software package is popular worldwide for deploying accelerator control systems. EPICS base allows building server applications that interact with EPICS compliant lower level hardware, embedded systems, commercial PLCs on one side and facilitates seamless connectivity with EPICS clients on the other side. Large number of such lower level (EPICS complaint) networked systems work in collaborative environment for physics experiment. RCnD has developed a PLC platform, Trombay Programmable Logic Controller TPLC-32 for deploying C and I systems of NPP and allied utilities. This platform is now also being used for deploying accelerator C and I systems. Hence the activity of developing TPLC-32 interface with EPICS was taken up in RCnD. This paper introduces the architecture of the EPICS Input Output Controller (IOC) and describes the implementation of the EPICS SoftIOC for TPLC-32. It also describes Operator Interface developed using MEDM EPICS client for LEHIPA vacuum control system built using TPLC-32. (author)

  12. Simulation using Xorbit with EPICS

    International Nuclear Information System (INIS)

    Evans, K. Jr.

    1995-01-01

    The accelerator code Xorbit has an interface to the Experimental Physics and Industrial Control System (EPICS). This means that machine data such as magnet settings can be sent to Xorbit via EPICS, and the resulting orbit parameters such as beta functions, etc., can be calculated. In addition, Xorbit can be made to simulate the real machine, whether the latter is running or not. To accomplish this for the APS, there is a database of process variables in an IOC corresponding to each APS ring and beamline. These process variables are very similar to the real process variables that read and set power supplies and read monitors, except that when a setting is changed, Xorbit is notified via a callback, calculates a new orbit, and outputs the appropriate readbacks to the database. By attaching the string ''Xorbit:'' to a control name the control system will respond to the simulation rather than the real system. This allows the testing of control algorithms, orbit diagnostics, and many other components of the control system (as well as EPICS itself). It is fast enough to be visually similar to accessing the real system

  13. Development of KOMAC Beam Monitoring System Using EPICS

    Energy Technology Data Exchange (ETDEWEB)

    Song, Young-Gi; Yun, Sang-Pil; Kim, Han-Sung; Kwon, Hyeok-Jung; Cho, Yong-Sub [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    The beam loss signals must be digitized and the sampling has to be synchronized to a reference signal which is an external trigger for beam operation. The digitized data must be accessible by the Experimental Physics and Industrial Control System (EPICS)-based control system, which manages the whole accelerator control. In order to satisfy the requirement, an Input /Output Controller (IOC), which runs Linux on a CPU module with PCI express based Analog to Digital Converter (ADC) modules, has been adopted. An associated linux driver and EPICS device support module also have been developed. The IOC meets the requirements and the development and maintenance of the software for the IOC is considerably efficient. The data acquisition system running EPICS will be used in increasing phase of KOrea Multi-purpose Accelerator Complex (KOMAC) beam power. The beam monitoring system integrates BLM and BPM signals into control system and offers real-time data to operators. The IOC, which is implemented with Linux and PCI driver, has supported data acquisition as a very flexible solution.

  14. Development of KOMAC Beam Monitoring System Using EPICS

    International Nuclear Information System (INIS)

    Song, Young-Gi; Yun, Sang-Pil; Kim, Han-Sung; Kwon, Hyeok-Jung; Cho, Yong-Sub

    2014-01-01

    The beam loss signals must be digitized and the sampling has to be synchronized to a reference signal which is an external trigger for beam operation. The digitized data must be accessible by the Experimental Physics and Industrial Control System (EPICS)-based control system, which manages the whole accelerator control. In order to satisfy the requirement, an Input /Output Controller (IOC), which runs Linux on a CPU module with PCI express based Analog to Digital Converter (ADC) modules, has been adopted. An associated linux driver and EPICS device support module also have been developed. The IOC meets the requirements and the development and maintenance of the software for the IOC is considerably efficient. The data acquisition system running EPICS will be used in increasing phase of KOrea Multi-purpose Accelerator Complex (KOMAC) beam power. The beam monitoring system integrates BLM and BPM signals into control system and offers real-time data to operators. The IOC, which is implemented with Linux and PCI driver, has supported data acquisition as a very flexible solution

  15. Feasibility of the Enhancing Participation In the Community by improving Wheelchair Skills (EPIC Wheels) program: study protocol for a randomized controlled trial.

    Science.gov (United States)

    Giesbrecht, Edward M; Miller, William C; Eng, Janice J; Mitchell, Ian M; Woodgate, Roberta L; Goldsmith, Charles H

    2013-10-24

    Many older adults rely on a manual wheelchair for mobility but typically receive little, if any, training on how to use their wheelchair effectively and independently. Standardized skill training is an effective intervention, but limited access to clinician trainers is a substantive barrier. Enhancing Participation in the Community by Improving Wheelchair Skills (EPIC Wheels) is a 1-month monitored home training program for improving mobility skills in older novice manual wheelchair users, integrating principles from andragogy and social cognitive theory. The purpose of this study is to determine whether feasibility indicators and primary clinical outcome measures of the EPIC Wheels program are sufficiently robust to justify conducting a subsequent multi-site randomized controlled trial. A 2 × 2 factorial randomized controlled trial at two sites will compare improvement in wheelchair mobility skills between an EPIC Wheels treatment group and a computer-game control group, with additional wheelchair use introduced as a second factor. A total of 40 community-dwelling manual wheelchair users at least 55 years old and living in two Canadian metropolitan cities (n = 20 × 2) will be recruited. Feasibility indicators related to study process, resources, management, and treatment issues will be collected during data collection and at the end of the study period, and evaluated against proposed criteria. Clinical outcome measures will be collected at baseline (pre-randomization) and post-intervention. The primary clinical outcome measure is wheelchair skill capacity, as determined by the Wheelchair Skills Test, version 4.1. Secondary clinical outcome measures include wheelchair skill safety, satisfaction with performance, wheelchair confidence, life-space mobility, divided-attention, and health-related quality of life. The EPIC Wheels training program offers several innovative features. The convenient, portable, economical, and adaptable tablet-based, home program model

  16. EPICS IOC development on open source RTEMS RTOS

    International Nuclear Information System (INIS)

    Bharade, S.K.; Joshi, Gopal; Das, D.

    2015-01-01

    Modern control systems applications are often built on top of a real time operating system. At LEHIPA beamlines, open source control systems offer a modem solution for cost effectiveness and technical competence. The 'Experimental Physics and Industrial Control System' (EPICS) and the 'Real-Time Operating System for Multiprocessor Systems' (RTEMS) were chosen to develop the core control system. Presently, the EPICS/RTEMS/MVME5500 control system is implemented for RF Protection Interlock system and BPM. This paper shares an experience of building RTEMS for MVME5500, configuring and run EPICS for RTEMS-MVME5500 architecture. It further shows EPICS bench marking results using EPICS catime and hamesstest utilities for this architecture. (author)

  17. Laboratory Instrumentation Design Research for Scalable Next Generation Epitaxy: Non-Equilibrium Wide Application Epitaxial Patterning by Intelligent Control (NEW-EPIC). Volume 1. 3D Composition/Doping Control via Micromiror Patterned Deep UV Photodesorption: Revolutionary in situ Characterization/Control

    Science.gov (United States)

    2009-02-19

    34 (to be submitted to APL) " Positron Annihilation Spectroscopy of Annealed and As-grown Be-doped GaN" (to be submitted to APL - delayed by the...WIDE APPLICATION EPITAXIAL PATTERNING BY INTELLIGENT CONTROL (NEW-EPIC) 6. AUTHOR(S) DRS DOOLITTILE, FRAZIER, BURNHAM, PRITCHETT, BILLINGSLEY...NEXT GENERATION EPITAXY: NON-EQUILIBRIUM WIDE APPLICATION EPITAXIAL PATTERNING BY INTELLIGENT CONTROL (NEW-EPIC) VOLUME I 3D COMPOSITION/DOPING

  18. Centrally managed name resolution schemes for EPICS

    International Nuclear Information System (INIS)

    Jun, D.

    1997-01-01

    The Experimental Physics and Industrial Control System (EPICS) uses a broadcast method to locate resources and controls distributed across control servers. There are many advantages offered by using a centrally managed name resolution method, in which resources are located using a repository. The suitability of DCE Directory Service as a name resolution method is explored, and results from a study involving DCE are discussed. An alternative nameserver method developed and in use at the Thomas Jefferson national Accelerator Facility (Jefferson Lab) is described and results of integrating this new method with existing EPICS utilities presented. The various methods discussed in the paper are compared

  19. Optimization and test of a digital radio-frequency control system and developments for the EPICS-based accelerator control system at the S-DALINAC

    International Nuclear Information System (INIS)

    Burandt, Christoph Warwick

    2017-01-01

    The first part of this thesis covers multiple extensions of the digital low-level radio-frequency control system of the electron accelerator S-DALINAC. This comprises bringing into regular operation the piezoelectrically driven fine tuners of the superconducting cavities. For this a power supply series has been developed, which is compatible with the existing electronics and can power the piezo elements. Furthermore the flexibility of the radio-frequency control system has been demonstrated on superconducting quarter-wave-resonators of the ion accelerator ALPI. These 160 MHz cavities are quite different to the S-DALINAC's acceleration structures but could be operated successfully with low residual errors in phase and amplitude nevertheless. The second part describes the migration of the accelerator control system to an EPICS-based system. A multitude of devices with a diversity of interfaces and protocols have been integrated and higher-level functionality has been unified. Within the framework of the construction of the third recirculation beam-line, the beam-path-length adjustment mechanism was motorized.

  20. Rapid application development by KEKB accelerator operators using EPICS/Python

    International Nuclear Information System (INIS)

    Tanaka, M.; Satoh, Y.; Kitabayashi, T.

    2004-01-01

    In the KEKB accelerator facility, the control system is constructed based on the framework of EPICS. By using EPICS/Python API, which is originated from KEK, we can develop an EPICS channel access application based on simple Python technology with only a few knowledge of EPICS channel access protocols. The operator's new tuning ideas are quickly implemented to the control system. In this paper, we introduce the EPICS/Python API and report the effectiveness of rapid application development by the KEKB operators using the API. (author)

  1. Formulation of EPICS record naming conventions in J-PARC linac and RCS. Build process of unique and standardized name

    International Nuclear Information System (INIS)

    Fukuta, Shinpei; Kawase, Masato; Kikuzawa, Nobuhiro; Watanabe, Kazuhiko; Sakaki, Hironao; Takahashi, Hiroki

    2011-02-01

    J-PARC (Japan Proton Accelerator Research Complex) accelerator devices are controlled by the use of the software called EPICS (Experimental Physics and Industrial Control System). The unique name called an EPICS record is given to a control signal and data acquisition, Accelerator device control is achieved using the EPICS record. The requirement for the EPICS record name is 2 points; (1) no overlap of the EPICS record name, (2) the control contents can be easily imagined from the EPICS record name. To manage the EPICS record using relational database for the information management of the accelerator device in J-PARC, the naming structure is required so that a mechanical process can be performed easily. It was necessary to standardize the EPICS record name and the EPICS record structure to achieve these requirements. Therefore, we have formulated a guideline called 'EPICS record naming conventions' to decide to an EPICS record name uniquely and standardization. The abbreviated key word list of the accelerator devices and the control signal that compose the EPICS record name is appended to the EPICS record naming conventions. (author)

  2. Psychometric Assessment of the Chinese Version of the Abbreviated Expanded Prostate Cancer Index Composite (EPIC-26) and the Clinical Practice Version (EPIC-CP) in Chinese Men With Prostate Cancer.

    Science.gov (United States)

    Lam, Wendy W T; Tse, Michael A; Ng, Chris N L; Chung, Edward K M; Fielding, Richard

    2017-06-01

    The Expanded Prostate Cancer Index Composite (EPIC) instrument was designed to assess a range of health-related quality-of-life issues specifically relevant to patients with prostate cancer. This study examined the validity and reliability of Chinese versions of the 26-item EPIC and of the 16-item EPIC for Clinical Practice (EPIC-CP) in Chinese patients with prostate cancer. A Chinese version of the 26-item EPIC and the 16-item EPIC-CP were self-completed by 252 Chinese patients with prostate cancer who were recruited from three community-based cancer service centers. Confirmatory factors analysis assessed the factor structures of the EPIC and the EPIC-CP. Internal consistency and construct and clinical validities of the factor structures were assessed. Confirmatory factor analysis revealed that the original factor structure of both EPIC-26 and EPIC-CP showed good fit to this sample. A correlated model was superior to a hierarchical model in both EPIC-26 and EPIC-CP supporting the utility of the domain scores over the total scores. Cronbach α ranged from 0.55 to 0.91 for EPIC-26 and 0.44 to 0.67 for EPIC-CP. Construct validity was supported by correlations between EPIC-26/EPIC-CP and psychological distress measures. Clinical validity was supported by differentiation between patients with and without prostatectomy. These Chinese versions of the five-factor EPIC-26 and the EPIC-CP are valid and practical measures for assessing a range of health-related quality-of-life issues related to the diagnosis and treatment of prostate cancer, highlighting their utility in assessing health-related quality of life for patients diagnosed with prostate cancer. Copyright © 2017 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

  3. Experience with EPICS in a wide variety of applications

    International Nuclear Information System (INIS)

    Kraimer, M.R.; Clausen, M.; Lupton, W.; Watson, C.

    1997-01-01

    Currently more than 70 organizations have obtained permission to use the Experimental Physics and Industrial Control System (EPICS), a set of software packages for building real-time control systems. In this paper representatives from four of these sites discuss the reasons their sites chose EPICS, provide a brief discussion of their control system development, and discuss additional control system tools obtained elsewhere or developed locally

  4. Experience with EPICS in a wide variety of applications

    Energy Technology Data Exchange (ETDEWEB)

    Kraimer, M.R. [Argonne National Lab., IL (United States); Clausen, M. [Deutsches Elektronen Synchrotron, Hamburg (Germany); Lupton, W. [W.M. Keck Observatory, Kamuela, HI (United States); Watson, C. [Thomas Jefferson National Accelerator Facility, Newport News, VA (United States)

    1997-08-01

    Currently more than 70 organizations have obtained permission to use the Experimental Physics and Industrial Control System (EPICS), a set of software packages for building real-time control systems. In this paper representatives from four of these sites discuss the reasons their sites chose EPICS, provide a brief discussion of their control system development, and discuss additional control system tools obtained elsewhere or developed locally.

  5. The EPICS process variable Gateway Version 2

    International Nuclear Information System (INIS)

    Evans, K.

    2005-01-01

    The EPICS Process Variable Gateway is both a Channel Access Server and Channel Access Client that provides a means for many clients, typically on different subnets, to access a process variable while making only one connection to the server that owns the process variable. It also provides additional access security beyond that implemented on the server. It thus protects critical servers while providing suitably restricted access to needed process variables. The original version of the Gateway worked with EPICS Base 3.13 but required a special version, since the changes necessary for its operation were never incorporated into EPICS Base. Version 2 works with any standard EPICS Base 3.14.6 or later and has many improvements in both performance and features over the older version. The Gateway is now used at many institutions and has become a stable, high-performance application. It is capable of handling tens of thousands of process variables with hundreds of thousands of events per second. It has run for over three months in a production environment without having to be restarted. It has many internal process variables that can be used to monitor its state using standard EPICS client tools, such as MEDM and StripTool. Other internal process variables can be used to stop the Gateway, make several kinds of reports, or change the access security without stopping the Gateway. It can even be started on remote workstations from MEDM by using a Secure Shell script. This paper will describe the new Gateway and how it is used. The Gateway is both a server (like an EPICS Input/Output Controller (IOC)) and a client (like the EPICS Motif Editor and Display Manager (MEDM), StripTool, and others). Clients connect to the server side, and the client side connects to IOCs and other servers, possibly other Gateways. See Fig. 1. There are perhaps three principal reasons for using the Gateway: (1) it allows many clients to access a process variable while making only one connection to

  6. Challenges in Comparative Oral Epic

    Directory of Open Access Journals (Sweden)

    John Miles Foley

    2012-10-01

    Full Text Available Originally written in 2001 and subsequently published in China, this collaborative essay explores five questions central to comparative oral epic with regard to Mongolian, South Slavic, ancient Greek, and Old English traditions: “What is a poem in oral epic tradition?” “What is a typical scene or theme in oral epic tradition?” “What is a poetic line in oral epic tradition?” “What is a formula in an oral epic tradition?” “What is the register in oral epic poetry?” Now available for the first time in English, this essay reflects a foundational stage of what has become a productive and long-term collaboration between the Center for Studies in Oral Tradition and the Institute of Ethnic Literature of the Chinese Academy of Social Sciences.

  7. Operational experience from a large EPICS-based accelerator facility

    International Nuclear Information System (INIS)

    Ciarlette, D.J.; Gerig, R.

    1995-01-01

    The Advanced Photon Source (APS) at Argonne National Laboratory is a third-generation x-ray light source which uses the Experimental Physics and Industrial Control System (EPICS) to operate its linear accelerator, positron accumulator ring, booster synchrotron, and storage ring equipment. EPICS has been used at the APS since the beginning of installation and commissioning. Currently, EPICS controls approximately 100 VME crates containing over 100,000 process variables. With this complexity, the APS has had to review some of the methods originally employed and make changes as necessary. In addition, due to commissioning and operational needs, higher-level operator software needed to be created. EPICS has been flexible enough to allow this

  8. EPICS MySQL Archiver - integration between EPICS and MySQL

    International Nuclear Information System (INIS)

    Roy, A.; Bhole, R.B.; Pal, S.; Sarkar, D.

    2012-01-01

    The performance evaluation and analysis of intersystem dependency of the various subsystems of the Superconducting Cyclotron (SCC) demand a well configured data logging, archiving and historic analysis facility for large number of control parameters along with on-line failure analysis facility of every system. Experimental Physics and Industrial Control System (EPICS) is used as development architecture of the control system of these systems with MySQL as database for large amount of relational data management. This combination requires integration between EPICS and MySQL server. For this purpose, MySQL Archiver as an EPICS Extension is developed for data logging and archiving of control parameters into MySQL database. This extension also provides a web based tool for online monitoring of control parameters and historic analysis of archived data. This paper describes the software architecture, implementation, as well as method of configuration for any other EPICS based control system as a utility. This facility is also elaborated with examples, web page views and experiences of deploying it in SCC. (author)

  9. EPICS - MDSplus integration in the ITER Neutral Beam Test Facility

    International Nuclear Information System (INIS)

    Luchetta, Adriano; Manduchi, Gabriele; Barbalace, Antonio; Soppelsa, Anton; Taliercio, Cesare

    2011-01-01

    SPIDER, the ITER-size ion-source test bed in the ITER Neutral Beam Test Facility, is a fusion device requiring a complex central system to provide control and data acquisition, referred to as CODAS. The CODAS software architecture will rely on EPICS and MDSplus, two open-source, collaborative software frameworks, targeted at control and data acquisition, respectively. EPICS has been selected as ITER CODAC middleware and, as the final deliverable of the Neutral Beam Test Facility is the procurement of the ITER Heating Neutral Beam Injector, we decided to adopt this ITER technology. MDSplus is a software package for data management, supporting advanced concepts, such as platform and underlying hardware independence, self description data, and data driven model. The combined use of EPICS and MDSplus is not new in fusion, but their level of integration will be new in SPIDER, achieved by a more refined data access layer. The paper presents the integration software to use effectively EPICS and MDSplus, including the definition of appropriate EPICS records to interact with MDSplus. The MDSplus and EPICS archive concepts are also compared on the basis of performance tests and data streaming is investigated by ad-hoc measurements.

  10. EPICS data archiver at SSRF beamlines

    International Nuclear Information System (INIS)

    Hu Zheng; Mi Qingru; Zheng Lifang; Li Zhong

    2014-01-01

    The control system of SSRF (Shanghai Synchrotron Radiation Facility) is based on EPICS (Experimental Physics and Industrial Control System). Operation data storage for synchrotron radiation facility is important for its status monitoring and analysis. At SSRF, operation data used to be index files recorded by traditional EPICS Channel Archiver. Nevertheless, index files are not suitable for long-term maintenance and difficult for data analysis. Now, RDB Channel Archiver and MySQL are used for SSRF beamline operation data archiving, so as to promote the data storage reliability and usability. By applying a new uploading mechanism to RDB Channel Archiver, its writing performance is improved. A web-based GUI (Graphics User Interface) is also developed to make it easier to access database. (authors)

  11. Helicobacter pylori infection, chronic corpus atrophic gastritis and pancreatic cancer risk in the European Prospective Investigation into Cancer and Nutrition (EPIC) cohort: A nested case-control study.

    Science.gov (United States)

    Huang, Jiaqi; Zagai, Ulrika; Hallmans, Göran; Nyrén, Olof; Engstrand, Lars; Stolzenberg-Solomon, Rachael; Duell, Eric J; Overvad, Kim; Katzke, Verena A; Kaaks, Rudolf; Jenab, Mazda; Park, Jin Young; Murillo, Raul; Trichopoulou, Antonia; Lagiou, Pagona; Bamia, Christina; Bradbury, Kathryn E; Riboli, Elio; Aune, Dagfinn; Tsilidis, Konstantinos K; Capellá, Gabriel; Agudo, Antonio; Krogh, Vittorio; Palli, Domenico; Panico, Salvatore; Weiderpass, Elisabete; Tjønneland, Anne; Olsen, Anja; Martínez, Begoña; Redondo-Sanchez, Daniel; Chirlaque, Maria-Dolores; Hm Peeters, Petra; Regnér, Sara; Lindkvist, Björn; Naccarati, Alessio; Ardanaz, Eva; Larrañaga, Nerea; Boutron-Ruault, Marie-Christine; Rebours, Vinciane; Barré, Amélie; Bueno-de-Mesquita, H B As; Ye, Weimin

    2017-04-15

    The association between H. pylori infection and pancreatic cancer risk remains controversial. We conducted a nested case-control study with 448 pancreatic cancer cases and their individually matched control subjects, based on the European Prospective Investigation into Cancer and Nutrition (EPIC) cohort, to determine whether there was an altered pancreatic cancer risk associated with H. pylori infection and chronic corpus atrophic gastritis. Conditional logistic regression models were applied to calculate odds ratios (ORs) and corresponding 95% confidence intervals (CIs), adjusted for matching factors and other potential confounders. Our results showed that pancreatic cancer risk was neither associated with H. pylori seropositivity (OR = 0.96; 95% CI: 0.70, 1.31) nor CagA seropositivity (OR = 1.07; 95% CI: 0.77, 1.48). We also did not find any excess risk among individuals seropositive for H. pylori but seronegative for CagA, compared with the group seronegative for both antibodies (OR = 0.94; 95% CI: 0.63, 1.38). However, we found that chronic corpus atrophic gastritis was non-significantly associated with an increased pancreatic cancer risk (OR = 1.35; 95% CI: 0.77, 2.37), and although based on small numbers, the excess risk was particularly marked among individuals seronegative for both H. pylori and CagA (OR = 5.66; 95% CI: 1.59, 20.19, p value for interaction cancer risk in western European populations. However, the suggested association between chronic corpus atrophic gastritis and pancreatic cancer risk warrants independent verification in future studies, and, if confirmed, further studies on the underlying mechanisms. © 2016 UICC.

  12. Optimization and test of a digital radio-frequency control system and developments for the EPICS-based accelerator control system at the S-DALINAC; Optimierung und Test der digitalen Hochfrequenzregelung und Entwicklung fuer das EPICS-basierte Beschleunigungskontrollsystem am S-DALINAC

    Energy Technology Data Exchange (ETDEWEB)

    Burandt, Christoph Warwick

    2017-07-01

    The first part of this thesis covers multiple extensions of the digital low-level radio-frequency control system of the electron accelerator S-DALINAC. This comprises bringing into regular operation the piezoelectrically driven fine tuners of the superconducting cavities. For this a power supply series has been developed, which is compatible with the existing electronics and can power the piezo elements. Furthermore the flexibility of the radio-frequency control system has been demonstrated on superconducting quarter-wave-resonators of the ion accelerator ALPI. These 160 MHz cavities are quite different to the S-DALINAC's acceleration structures but could be operated successfully with low residual errors in phase and amplitude nevertheless. The second part describes the migration of the accelerator control system to an EPICS-based system. A multitude of devices with a diversity of interfaces and protocols have been integrated and higher-level functionality has been unified. Within the framework of the construction of the third recirculation beam-line, the beam-path-length adjustment mechanism was motorized.

  13. Comparison of the EPIC Physical Activity Questionnaire with Combined Heart Rate and Movement Sensing in a Nationally Representative Sample of Older British Adults

    Science.gov (United States)

    España-Romero, Vanesa; Golubic, Rajna; Martin, Kathryn R.; Hardy, Rebecca; Ekelund, Ulf; Kuh, Diana; Wareham, Nicholas J.; Cooper, Rachel; Brage, Soren

    2014-01-01

    Objectives To compare physical activity (PA) subcomponents from EPIC Physical Activity Questionnaire (EPAQ2) and combined heart rate and movement sensing in older adults. Methods Participants aged 60–64y from the MRC National Survey of Health and Development in Great Britain completed EPAQ2, which assesses self-report PA in 4 domains (leisure time, occupation, transportation and domestic life) during the past year and wore a combined sensor for 5 consecutive days. Estimates of PA energy expenditure (PAEE), sedentary behaviour, light (LPA) and moderate-to-vigorous PA (MVPA) were obtained from EPAQ2 and combined sensing and compared. Complete data were available in 1689 participants (52% women). Results EPAQ2 estimates of PAEE and MVPA were higher than objective estimates and sedentary time and LPA estimates were lower [bias (95% limits of agreement) in men and women were 32.3 (−61.5 to 122.6) and 29.0 (−39.2 to 94.6) kJ/kg/day for PAEE; −4.6 (−10.6 to 1.3) and −6.0 (−10.9 to −1.0) h/day for sedentary time; −171.8 (−454.5 to 110.8) and −60.4 (−367.5 to 246.6) min/day for LPA; 91.1 (−159.5 to 341.8) and 55.4 (−117.2 to 228.0) min/day for MVPA]. There were significant positive correlations between all self-reported and objectively assessed PA subcomponents (rho  = 0.12 to 0.36); the strongest were observed for MVPA (rho = 0.30 men; rho = 0.36 women) and PAEE (rho = 0.26 men; rho = 0.25 women). Conclusion EPAQ2 produces higher estimates of PAEE and MVPA and lower estimates of sedentary and LPA than objective assessment. However, both methodologies rank individuals similarly, suggesting that EPAQ2 may be used in etiological studies in this population. PMID:24516543

  14. Comparison of the EPIC Physical Activity Questionnaire with combined heart rate and movement sensing in a nationally representative sample of older British adults.

    Directory of Open Access Journals (Sweden)

    Vanesa España-Romero

    Full Text Available To compare physical activity (PA subcomponents from EPIC Physical Activity Questionnaire (EPAQ2 and combined heart rate and movement sensing in older adults.Participants aged 60-64y from the MRC National Survey of Health and Development in Great Britain completed EPAQ2, which assesses self-report PA in 4 domains (leisure time, occupation, transportation and domestic life during the past year and wore a combined sensor for 5 consecutive days. Estimates of PA energy expenditure (PAEE, sedentary behaviour, light (LPA and moderate-to-vigorous PA (MVPA were obtained from EPAQ2 and combined sensing and compared. Complete data were available in 1689 participants (52% women.EPAQ2 estimates of PAEE and MVPA were higher than objective estimates and sedentary time and LPA estimates were lower [bias (95% limits of agreement in men and women were 32.3 (-61.5 to 122.6 and 29.0 (-39.2 to 94.6 kJ/kg/day for PAEE; -4.6 (-10.6 to 1.3 and -6.0 (-10.9 to -1.0 h/day for sedentary time; -171.8 (-454.5 to 110.8 and -60.4 (-367.5 to 246.6 min/day for LPA; 91.1 (-159.5 to 341.8 and 55.4 (-117.2 to 228.0 min/day for MVPA]. There were significant positive correlations between all self-reported and objectively assessed PA subcomponents (rho= 0.12 to 0.36; the strongest were observed for MVPA (rho = 0.30 men; rho = 0.36 women and PAEE (rho = 0.26 men; rho = 0.25 women.EPAQ2 produces higher estimates of PAEE and MVPA and lower estimates of sedentary and LPA than objective assessment. However, both methodologies rank individuals similarly, suggesting that EPAQ2 may be used in etiological studies in this population.

  15. EPICS GPIB device support

    International Nuclear Information System (INIS)

    Winans, J.

    1993-01-01

    A GPIB device support module is used to provide access to the operating parameters of a GPIB device. GPIB devices may be accessed via National Instruments 1014 cards or via Bitbus Universal Gateways. GPIB devices typically have many parameters, each of which may be thought of in terms of the standard types of database records available in EPICS. It is the job of the device support module designer to decide how the mapping of these parameters will be made to the available record types. Once this mapping is complete, the device support module may be written. The writing of the device support module consists primarily of the construction of a parameter table. This table is used to associate the database record types with the operating parameters of the GPIB instrument. Other aspects of module design include the handling of SRQ events and errors. SRQ events are made available to the device support module if so desired. The processing of an SRQ event is completely up to the designer of the module. They may be ignored, tied to event based record processing, or anything else the designer wishes. Error conditions may be handled in a similar fashion

  16. Are Metabolic Signatures Mediating the Relationship between Lifestyle Factors and Hepatocellular Carcinoma Risk? Results from a Nested Case-Control Study in EPIC.

    Science.gov (United States)

    Assi, Nada; Thomas, Duncan C; Leitzmann, Michael; Stepien, Magdalena; Chajès, Véronique; Philip, Thierry; Vineis, Paolo; Bamia, Christina; Boutron-Ruault, Marie-Christine; Sandanger, Torkjel M; Molinuevo, Amaia; Boshuizen, Hendriek C; Sundkvist, Anneli; Kühn, Tilman; Travis, Ruth C; Overvad, Kim; Riboli, Elio; Gunter, Marc J; Scalbert, Augustin; Jenab, Mazda; Ferrari, Pietro; Viallon, Vivian

    2018-05-01

    Background: The "meeting-in-the-middle" (MITM) is a principle to identify exposure biomarkers that are also predictors of disease. The MITM statistical framework was applied in a nested case-control study of hepatocellular carcinoma (HCC) within European Prospective Investigation into Cancer and Nutrition (EPIC), where healthy lifestyle index (HLI) variables were related to targeted serum metabolites. Methods: Lifestyle and targeted metabolomic data were available from 147 incident HCC cases and 147 matched controls. Partial least squares analysis related 7 lifestyle variables from a modified HLI to a set of 132 serum-measured metabolites and a liver function score. Mediation analysis evaluated whether metabolic profiles mediated the relationship between each lifestyle exposure and HCC risk. Results: Exposure-related metabolic signatures were identified. Particularly, the body mass index (BMI)-associated metabolic component was positively related to glutamic acid, tyrosine, PC aaC38:3, and liver function score and negatively to lysoPC aC17:0 and aC18:2. The lifetime alcohol-specific signature had negative loadings on sphingomyelins (SM C16:1, C18:1, SM(OH) C14:1, C16:1 and C22:2). Both exposures were associated with increased HCC with total effects (TE) = 1.23 (95% confidence interval = 0.93-1.62) and 1.40 (1.14-1.72), respectively, for BMI and alcohol consumption. Both metabolic signatures mediated the association between BMI and lifetime alcohol consumption and HCC with natural indirect effects, respectively, equal to 1.56 (1.24-1.96) and 1.09 (1.03-1.15), accounting for a proportion mediated of 100% and 24%. Conclusions: In a refined MITM framework, relevant metabolic signatures were identified as mediators in the relationship between lifestyle exposures and HCC risk. Impact: The understanding of the biological basis for the relationship between modifiable exposures and cancer would pave avenues for clinical and public health interventions on metabolic mediators

  17. EPICS: Channel Access security design

    International Nuclear Information System (INIS)

    Kraimer, M.; Hill, J.

    1994-05-01

    This document presents the design for implementing the requirements specified in: EPICS -- Channel Access Security -- functional requirements, Ned. D. Arnold, 03/09/92. Use of the access security system is described along with a summary of the functional requirements. The programmer's interface is given. Security protocol is described and finally aids for reading the access security code are provided

  18. A shared memory based interface of MARTe with EPICS for real-time applications

    International Nuclear Information System (INIS)

    Yun, Sangwon; Neto, André C.; Park, Mikyung; Lee, Sangil; Park, Kaprai

    2014-01-01

    Highlights: • We implemented a shared memory based interface of MARTe with EPICS. • We implemented an EPICS module supporting device and driver support. • We implemented an example EPICS IOC and CSS OPI for evaluation. - Abstract: The Multithreaded Application Real-Time executor (MARTe) is a multi-platform C++ middleware designed for the implementation of real-time control systems. It currently supports the Linux, Linux + RTAI, VxWorks, Solaris and MS Windows platforms. In the fusion community MARTe is being used at JET, COMPASS, ISTTOK, FTU and RFX in fusion [1]. The Experimental Physics and Industrial Control System (EPICS), a standard framework for the control systems in KSTAR and ITER, is a set of software tools and applications which provide a software infrastructure for use in building distributed control systems to operate devices. For a MARTe based application to cooperate with an EPICS based application, an interface layer between MARTe and EPICS is required. To solve this issue, a number of interfacing solutions have been proposed and some of them have been implemented. Nevertheless, a new approach is required to mitigate the functional limitations of existing solutions and to improve their performance for real-time applications. This paper describes the design and implementation of a shared memory based interface between MARTe and EPICS

  19. A shared memory based interface of MARTe with EPICS for real-time applications

    Energy Technology Data Exchange (ETDEWEB)

    Yun, Sangwon, E-mail: yunsw@nfri.re.kr [National Fusion Research Institute (NFRI), Gwahangno 169-148, Yuseong-Gu, Daejeon 305-806 (Korea, Republic of); Neto, André C. [Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, P-1049-001 Lisboa (Portugal); Park, Mikyung; Lee, Sangil; Park, Kaprai [National Fusion Research Institute (NFRI), Gwahangno 169-148, Yuseong-Gu, Daejeon 305-806 (Korea, Republic of)

    2014-05-15

    Highlights: • We implemented a shared memory based interface of MARTe with EPICS. • We implemented an EPICS module supporting device and driver support. • We implemented an example EPICS IOC and CSS OPI for evaluation. - Abstract: The Multithreaded Application Real-Time executor (MARTe) is a multi-platform C++ middleware designed for the implementation of real-time control systems. It currently supports the Linux, Linux + RTAI, VxWorks, Solaris and MS Windows platforms. In the fusion community MARTe is being used at JET, COMPASS, ISTTOK, FTU and RFX in fusion [1]. The Experimental Physics and Industrial Control System (EPICS), a standard framework for the control systems in KSTAR and ITER, is a set of software tools and applications which provide a software infrastructure for use in building distributed control systems to operate devices. For a MARTe based application to cooperate with an EPICS based application, an interface layer between MARTe and EPICS is required. To solve this issue, a number of interfacing solutions have been proposed and some of them have been implemented. Nevertheless, a new approach is required to mitigate the functional limitations of existing solutions and to improve their performance for real-time applications. This paper describes the design and implementation of a shared memory based interface between MARTe and EPICS.

  20. A MySQL Based EPICS Archiver

    Energy Technology Data Exchange (ETDEWEB)

    Christopher Slominski

    2009-10-01

    Archiving a large fraction of the EPICS signals within the Jefferson Lab (JLAB) Accelerator control system is vital for postmortem and real-time analysis of the accelerator performance. This analysis is performed on a daily basis by scientists, operators, engineers, technicians, and software developers. Archiving poses unique challenges due to the magnitude of the control system. A MySQL Archiving system (Mya) was developed to scale to the needs of the control system; currently archiving 58,000 EPICS variables, updating at a rate of 11,000 events per second. In addition to the large collection rate, retrieval of the archived data must also be fast and robust. Archived data retrieval clients obtain data at a rate over 100,000 data points per second. Managing the data in a relational database provides a number of benefits. This paper describes an archiving solution that uses an open source database and standard off the shelf hardware to reach high performance archiving needs. Mya has been in production at Jefferson Lab since February of 2007.

  1. A MySQL Based EPICS Archiver

    International Nuclear Information System (INIS)

    Slominski, Christopher

    2009-01-01

    Archiving a large fraction of the EPICS signals within the Jefferson Lab (JLAB) Accelerator control system is vital for postmortem and real-time analysis of the accelerator performance. This analysis is performed on a daily basis by scientists, operators, engineers, technicians, and software developers. Archiving poses unique challenges due to the magnitude of the control system. A MySQL Archiving system (Mya) was developed to scale to the needs of the control system; currently archiving 58,000 EPICS variables, updating at a rate of 11,000 events per second. In addition to the large collection rate, retrieval of the archived data must also be fast and robust. Archived data retrieval clients obtain data at a rate over 100,000 data points per second. Managing the data in a relational database provides a number of benefits. This paper describes an archiving solution that uses an open source database and standard off the shelf hardware to reach high performance archiving needs. Mya has been in production at Jefferson Lab since February of 2007.

  2. Usability of human Infinium MethylationEPIC BeadChip for mouse DNA methylation studies.

    Science.gov (United States)

    Needhamsen, Maria; Ewing, Ewoud; Lund, Harald; Gomez-Cabrero, David; Harris, Robert Adam; Kular, Lara; Jagodic, Maja

    2017-11-15

    The advent of array-based genome-wide DNA methylation methods has enabled quantitative measurement of single CpG methylation status at relatively low cost and sample input. Whereas the use of Infinium Human Methylation BeadChips has shown great utility in clinical studies, no equivalent tool is available for rodent animal samples. We examined the feasibility of using the new Infinium MethylationEPIC BeadChip for studying DNA methylation in mouse. In silico, we identified 19,420 EPIC probes (referred as mEPIC probes), which align with a unique best alignment score to the bisulfite converted reference mouse genome mm10. Further annotation revealed that 85% of mEPIC probes overlapped with mm10.refSeq genes at different genomic features including promoters (TSS1500 and TSS200), 1st exons, 5'UTRs, 3'UTRs, CpG islands, shores, shelves, open seas and FANTOM5 enhancers. Hybridization of mouse samples to Infinium Human MethylationEPIC BeadChips showed successful measurement of mEPIC probes and reproducibility between inter-array biological replicates. Finally, we demonstrated the utility of mEPIC probes for data exploration such as hierarchical clustering. Given the absence of cost and labor convenient genome-wide technologies in the murine system, our findings show that the Infinium MethylationEPIC BeadChip platform is suitable for investigation of the mouse methylome. Furthermore, we provide the "mEPICmanifest" with genomic features, available to users of Infinium Human MethylationEPIC arrays for mouse samples.

  3. A Nested Case-Control Study of Metabolically Defined Body Size Phenotypes and Risk of Colorectal Cancer in the European Prospective Investigation into Cancer and Nutrition (EPIC.

    Directory of Open Access Journals (Sweden)

    Neil Murphy

    2016-04-01

    Full Text Available Obesity is positively associated with colorectal cancer. Recently, body size subtypes categorised by the prevalence of hyperinsulinaemia have been defined, and metabolically healthy overweight/obese individuals (without hyperinsulinaemia have been suggested to be at lower risk of cardiovascular disease than their metabolically unhealthy (hyperinsulinaemic overweight/obese counterparts. Whether similarly variable relationships exist for metabolically defined body size phenotypes and colorectal cancer risk is unknown.The association of metabolically defined body size phenotypes with colorectal cancer was investigated in a case-control study nested within the European Prospective Investigation into Cancer and Nutrition (EPIC study. Metabolic health/body size phenotypes were defined according to hyperinsulinaemia status using serum concentrations of C-peptide, a marker of insulin secretion. A total of 737 incident colorectal cancer cases and 737 matched controls were divided into tertiles based on the distribution of C-peptide concentration amongst the control population, and participants were classified as metabolically healthy if below the first tertile of C-peptide and metabolically unhealthy if above the first tertile. These metabolic health definitions were then combined with body mass index (BMI measurements to create four metabolic health/body size phenotype categories: (1 metabolically healthy/normal weight (BMI < 25 kg/m2, (2 metabolically healthy/overweight (BMI ≥ 25 kg/m2, (3 metabolically unhealthy/normal weight (BMI < 25 kg/m2, and (4 metabolically unhealthy/overweight (BMI ≥ 25 kg/m2. Additionally, in separate models, waist circumference measurements (using the International Diabetes Federation cut-points [≥80 cm for women and ≥94 cm for men] were used (instead of BMI to create the four metabolic health/body size phenotype categories. Statistical tests used in the analysis were all two-sided, and a p-value of <0.05 was

  4. The implement of the interface between EPICS and LabVIEW

    International Nuclear Information System (INIS)

    Liu Jia; Wang Chunhong

    2009-01-01

    The control system of BEPCII (Beijing Electron Positron Collider) is based on EPICS (Experimental Physics and Industrial Control System). LabVIEW is often used to develop data acquisition system on Windows platform. EPICS IOC version 3.14 or later, can be currently running on windows. The SharedMemory developed by SNS (Spallation Neutron Source) can implement the interface between Windows IOC and LabVIEW. The paper describes the method how to use SharedMemory and a application of magnet measurement system, so that LabVIEW and EPICS can share data each other. (authors)

  5. Gravimetric dust sampling for control purposes and occupational dust sampling.

    CSIR Research Space (South Africa)

    Unsted, AD

    1997-02-01

    Full Text Available Prior to the introduction of gravimetric dust sampling, konimeters had been used for dust sampling, which was largely for control purposes. Whether or not absolute results were achievable was not an issue since relative results were used to evaluate...

  6. The PSI web interface to the EPICS channel archiver

    International Nuclear Information System (INIS)

    Gaudenz Jud; Luedeke, A.; Portmann, W.

    2012-01-01

    the EPICS (Experimental Physics and Industrial Control System) channel archiver is used at different facilities at PSI (Paul Scherrer Institute) like the Swiss Light Source or the medical cyclotron. The EPICS channel archiver is a powerful tool to collect control system data of thousands of EPICS process variables with rates of many Hertz each to an archive for later retrieval. Within the package of the channel archiver version 2 you get a Java application for graphical data retrieval and a command line tool for data extraction into different file formats. For the Paul Scherrer Institute (PSI) we wanted a possibility to retrieve the archived data from a web interface. It was desired to have flexible retrieval functions and to allow interchanging data references by e-mail. This web interface has been implemented by the PSI controls group and has now been in operation for several years. This paper will highlight the special features of the PSI web interface to the EPICS channel archiver

  7. A study of some features of the ultra high vacuum systems for EPIC

    International Nuclear Information System (INIS)

    Elsey, R.J.; Bennett, J.R.J.; Dossett, A.J.

    1977-01-01

    This report covers the experimental work carried out towards the development of the ultra high vacuum for the proposed electron positron storage ring, EPIC. Experiments included outgassing tests on samples of materials and pump-down tests on full scale aluminium vessels. The effect of baking was investigated. The approval of the similar machine PETRA at Hamburg and the subsequent withdrawal of the EPIC proposal in October 1975 curtailed the vacuum work. The experiments reported here are therefore incomplete, but nevertheless proved useful in showing that there should have been no major problems with building the vacuum system for EPIC. (author)

  8. Prospect-EPIC Utrecht: study design and characteristics of the cohort population. European Prospective Investigation into Cancer and Nutrition.

    Science.gov (United States)

    Boker, L K; van Noord, P A; van der Schouw, Y T; Koot, N V; Bueno de Mesquita, H B; Riboli, E; Grobbee, D E; Peeters, P H

    2001-01-01

    The European Prospective Investigation into Cancer and Nutrition (EPIC), which has been established in order to investigate the relations between nutrition and cancer, was initiated in 1990 and involves 10 European countries with heterogeneous dietary patterns and differing cancer incidence rates. This manuscript presents the design, recruitment and baseline characteristics of the Prospect-EPIC cohort co-ordinated in Utrecht, The Netherlands. The cohort is based on volunteers recruited among women participating in a regional breast cancer screening program. It comprises of 17,357 subjects aged 50-69 years at enrolment from Utrecht and vicinity, who have consented to participate in the study and its follow-up. Each participant filled out a general questionnaire and a food frequency questionnaire. Participants were also physically examined and have donated a blood sample. Participation rate was 34.5%. Blood samples were donated by most participants (97.5%) and detailed informed consents were obtained from 87.4% of participants. Mean age at enrolment was 57 years. Anthropometric, lifestyle and morbidity characteristics of the cohort population did not differ largely from those of similar study populations in The Netherlands. Based on the Prospect-EPIC population, we intend to conduct prospective total cohort, nested case-control or case-cohort studies, in order to investigate relations between consumption of certain food groups or nutrients and chronic diseases, including hormone dependant cancers such as breast, colon, endometrial and ovary cancers.

  9. Extrasolar Planetary Imaging Coronagraph (EPIC)

    Science.gov (United States)

    Clampin, Mark

    2009-01-01

    The Extrasolar Planetary Imaging Coronagraph (EPIC) is a proposed NASA Exoplanet Probe mission to image and characterize extrasolar giant planets. EPIC will provide insights into the physical nature and architecture of a variety of planets in other solar systems. Initially, it will detect and characterize the atmospheres of planets identified by radial velocity surveys, determine orbital inclinations and masses and characterize the atmospheres around A and F type stars which cannot be found with RV techniques. It will also observe the inner spatial structure of exozodiacal disks. EPIC has a heliocentric Earth trailing drift-away orbit, with a 5 year mission lifetime. The robust mission design is simple and flexible ensuring mission success while minimizing cost and risk. The science payload consists of a heritage optical telescope assembly (OTA), and visible nulling coronagraph (VNC) instrument. The instrument achieves a contrast ratio of 10^9 over a 5 arcsecond field-of-view with an unprecedented inner working angle of 0.13 arcseconds over the spectral range of 440-880 nm. The telescope is a 1.65 meter off-axis Cassegrain with an OTA wavefront error of lambda/9, which when coupled to the VNC greatly reduces the requirements on the large scale optics.

  10. Epic Allies, a Gamified Mobile Phone App to Improve Engagement in Care, Antiretroviral Uptake, and Adherence Among Young Men Who Have Sex With Men and Young Transgender Women Who Have Sex With Men: Protocol for a Randomized Controlled Trial.

    Science.gov (United States)

    LeGrand, Sara; Muessig, Kathryn E; Platt, Alyssa; Soni, Karina; Egger, Joseph R; Nwoko, Nkechinyere; McNulty, Tobias; Hightow-Weidman, Lisa B

    2018-04-05

    In the United States, young men who have sex with men (YMSM) and transgender women who have sex with men (YTWSM) bear a disproportionate burden of prevalent and incident HIV infections. Once diagnosed, many YMSM and YTWSM struggle to engage in HIV care, adhere to antiretroviral therapy (ART), and achieve viral suppression. Computer-based interventions, including those focused on behavior change, are recognized as effective tools for engaging youth. The purpose of the study described in this protocol is to evaluate the efficacy of Epic Allies, a theory-based mobile phone app that utilizes game mechanics and social networking features to improve engagement in HIV care, ART uptake, ART adherence, and viral suppression among HIV-positive YMSM and YTWSM. The study also qualitatively assesses intervention acceptability, perceived impact, and sustainability. This is a two-group, active-control randomized controlled trial of the Epic Allies app. YMSM and YTWSM aged 16 to 24 inclusive, with detectable HIV viral load are randomized 1:1 within strata of new to care (newly entered HIV medical care ≤12 months of baseline visit) or ART-nonadherent (first entered HIV medical care >12 months before baseline visit) to intervention or control conditions. The intervention condition addresses ART adherence barriers through medication reminders and adherence monitoring, tracking of select adherence-related behaviors (eg, alcohol and marijuana use), an interactive dashboard that displays the participant's adherence-related behaviors and provides tailored feedback, encouragement messages from other users, daily HIV/ART educational articles, and gamification features (eg, mini-games, points, badges) to increase motivation for behavior change and app engagement. The control condition features weekly phone-based notifications to encourage participants to view educational information in the control app. Follow-up assessments are administered at 13, 26, and 39 weeks for each arm. The

  11. The Philippine Epics and Ballads Multimedia Archive

    Directory of Open Access Journals (Sweden)

    Nicole Revel

    2013-10-01

    Full Text Available This essay offers an introduction to the Philippine Epics and Ballads Archive. This collection is a joint endeavor between singers, scholars, knowledgeable local persons, and technical assistants. This archive exemplifies a part of the cultural heritage among 15 national cultural communities and their respective languages. A multi-media eCompanion offers an interactive version of a Palawan epic song.

  12. EPICS SCA CLIENTS ON THE .NET X64 PLATFORM

    International Nuclear Information System (INIS)

    Timossi, Chris; Nishimura, Hiroshi

    2006-01-01

    We have developed a .NET assembly, which we call SCA.NET, which we have been using for building EPICS based control room applications at the Advanced Light Source (ALS). In this paper we report on our experiences building a 64-bit version of SCA.NET and the underlying channel access libraries for Windows XP x64 (using a dual core AMD Athlon CPU). We also report on our progress in building new accelerator control applications for this environment

  13. Radiation monitoring system based on EPICS

    International Nuclear Information System (INIS)

    Wang Weizhen; Li Jianmin; Wang Xiaobing; Hua Zhengdong; Xu Xunjiang

    2008-01-01

    Shanghai Synchrotron Radiation Facility (SSRF for short) is a third-generation light source building in China, including a 150 MeV injector, 3.5 GeV booster, 3.5 GeV storage ring and an amount of beam line stations. During operation, a mass of Synchrotron Radiation will be produced by electrons in the booster and the storage ring. Bremsstrahlung and neutrons will also be produced as a result of the interaction between the electrons, especially the beam loss, and the wall of the vacuum beam pipe. SSRF Radiation Monitoring System is established for monitoring the radiation dosage of working area and environment while SSRF operating. The system consists of detectors, intelligent data-collecting modules, monitoring computer, and managing computer. The software system is developed based on EPICS (Experimental Physics and Industrial Control System), implementing the collecting and monitoring the data output from intelligent modules, analyzing the data, and so on. (authors)

  14. A Woman Voice in an Epic: Tracing Gendered Motifs in Anne Vabarna's Peko

    Directory of Open Access Journals (Sweden)

    Andreas Kalkun

    2008-12-01

    Full Text Available In the article the gendered motifs found in Anne Vabarna’s Seto epic Peko are analysed. Besides the narrative telling of the life of the male hero, the motives regarding eating, refusing to eat or offering food, and the aspect of the female body or its control deserve to be noticed. These scenes do not communicate the main plot, they are often related to minor characters of the epic and slow down the narrative, but at the same time they clearly carry artistic purpose and meaning. I consider these motifs, present in the liminal parts of the epic, to be the dominant symbols of the epic where the author’s feminine world is being exposed. Observing these motifs of Peko in the context of Seto religious worldview, the life of Anne Vabarna and the social position of Seto women, the symbols become eloquent and informative.

  15. Lessons learned enhancing EPICS CA for LANSCE timed and flavored data

    International Nuclear Information System (INIS)

    Hill, Jeffrey O.

    2009-01-01

    A previous paper described an upgrade to EPICS enabling client side tools at LANSCE to receive subscription updates filtered selectively to match a logical configuration of LANSCE beam gates, as configured by the control room. The upgrade required fundamental changes in the EPICS core components. First, the event queue in the EPICS server was upgraded to buffer record (function block) and device specific parameters accessed generically via software interfaces for introspection of 3rd party data. In contrast, event queues in previous versions of EPICS were strictly limited to buffering only value, timestamp, and alarm status tuples. Second, the Channel Access server is being upgraded to filter subscription updates. In this follow on paper some necessary design changes mid-project and the lessons learned during the software development will be described.

  16. Software for NAA sample changer control

    Energy Technology Data Exchange (ETDEWEB)

    Dutra Neto, Aimore; Menezes, Maria Angela de B.C., E-mail: dutraa@cdtn.br, E-mail: menezes@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-RJ), Belo Horizonte, MG (Brazil)

    2015-07-01

    In CDTN/CNEN laboratories, the neutron activation analysis (NAA) is an analytical technique routinely employed. The irradiation is performed in the TRIGA MARK I IPR-R1 reactor. After irradiated, the samples depend of an operator to be changed, creating a bottle neck in the process. To optimize the whole process, an automation of the changing samples is necessary. In order to achieve this goal, it was developed a software to control a sample changer under construction at CDTN laboratories. Two programs, running in two different environments, manages the entire acquisition process and performs all activities necessary to move the motors to positioning the samples and control the vacuum to grip the vials. The high level routine communicates with Genie 2000 software to control a Canberra Multiport II, while a low level program controls the physical assemble. (author)

  17. Automated sampling and control of gaseous simulations

    KAUST Repository

    Huang, Ruoguan; Keyser, John

    2013-01-01

    In this work, we describe a method that automates the sampling and control of gaseous fluid simulations. Several recent approaches have provided techniques for artists to generate high-resolution simulations based on a low-resolution simulation

  18. Software for NAA sample changer control

    International Nuclear Information System (INIS)

    Dutra Neto, Aimore; Menezes, Maria Angela de B.C.

    2015-01-01

    In CDTN/CNEN laboratories, the neutron activation analysis (NAA) is an analytical technique routinely employed. The irradiation is performed in the TRIGA MARK I IPR-R1 reactor. After irradiated, the samples depend of an operator to be changed, creating a bottle neck in the process. To optimize the whole process, an automation of the changing samples is necessary. In order to achieve this goal, it was developed a software to control a sample changer under construction at CDTN laboratories. Two programs, running in two different environments, manages the entire acquisition process and performs all activities necessary to move the motors to positioning the samples and control the vacuum to grip the vials. The high level routine communicates with Genie 2000 software to control a Canberra Multiport II, while a low level program controls the physical assemble. (author)

  19. EPICS: operating system independent device/driver support

    International Nuclear Information System (INIS)

    Kraimer, M.R.

    2003-01-01

    Originally EPICS input/output controllers (IOCs) were only supported on VME-based systems running the vxWorks operating system. Now IOCs are supported on many systems: vxWorks, RTEMS, Solaris, HPUX, Linux, WIN32, and Darwin. A challenge is to provide operating-system-independent device and driver support. This paper presents some techniques for providing such support. EPICS (Experimental Physics and Industrial Control System) is a set of software tools, libraries, and applications developed collaboratively and used worldwide to create distributed, real-time control systems for scientific instruments such as particle accelerators, telescopes, and other large scientific experiments. An important component of all EPICS-based control systems is a collection of input/output controllers (IOCs). An IOC has three primary components: (1) a real-time database; (2) channel access, which provides network access to the database; and (3) device/driver support for interfacing to equipment. This paper describes some projects related to providing device/driver support on non-vxWorks systems. In order to support IOCs on platforms other than vxWorks, operating-system-independent (OSI) application program interfaces (APIs) were defined for threads, semaphores, timers, etc. Providing support for a new platform consists of providing an operating-system-dependent implementation of the OSI APIs.

  20. EPICS V4 Evaluation for SNS Neutron Data

    Energy Technology Data Exchange (ETDEWEB)

    Kasemir, Kay [ORNL; Pearson, Matthew R [ORNL; Guyotte, Greg S [ORNL

    2015-01-01

    Version 4 of the Experimental Physics and Industrial Control System (EPICS) toolkit allows defining application-specific structured data types (pvData) and offers a network protocol for their efficient exchange (pvAccess). We evaluated V4 for the transport of neutron events from the detectors of the Spallation Neutron Source (SNS) to data acquisition and experiment monitoring systems. This includes the comparison of possible data structures, performance tests, and experience using V4 in production on a beam line.

  1. Controlled sample program publication No. 1: characterization of rock samples

    International Nuclear Information System (INIS)

    Ames, L.L.

    1978-10-01

    A description is presented of the methodology used and the geologic parameters measured on several rocks which are being used in round-robin laboratory and nuclide adsorption methodology experiments. Presently investigators from various laboratories are determining nuclide distribution coefficients utilizing numerous experimental techniques. Unfortunately, it appears that often the resultant data are dependent not only on the type of groundwater and rock utilized, but also on the experimentor or method used. The Controlled Sample Program is a WISAP (Waste Isolation Safety Assessment Program) attempt to resolve the apparent method and dependencies and to identify individual experimenter's bias. The rock samples characterized in an interlaboratory Kd methodology comparison program include Westerly granite, Argillaceous shale, Oolitic limestone, Sentinel Gap basalt, Conasauga shale, Climax Stock granite, anhydrite, Magenta dolomite and Culebra dolomite. Techniques used in the characterization include whole rock chemical analysis, X-ray diffraction, optical examination, electron microprobe elemental mapping, and chemical analysis of specific mineral phases. Surface areas were determined by the B.E.T. and ethylene glycol sorption methods. Cation exchange capacities were determined with 85 Sr, but were of questionable value for the high calcium rocks. A quantitative mineralogy was also estimated for each rock. Characteristics which have the potential of strongly affecting radionuclide Kd values such as the presence of sulfides, water-soluble, pH-buffering carbonates, glass, and ferrous iron were listed for each rock sample

  2. Doing accelerator physics using SDDS, UNIX, and EPICS

    International Nuclear Information System (INIS)

    Borland, M.; Emery, L.; Sereno, N.

    1995-01-01

    The use of the SDDS (Self-Describing Data Sets) file protocol, together with the UNIX operating system and EPICS (Experimental Physics and Industrial Controls System), has proved powerful during the commissioning of the APS (Advanced Photon Source) accelerator complex. The SDDS file protocol has permitted a tool-oriented approach to developing applications, wherein generic programs axe written that function as part of multiple applications. While EPICS-specific tools were written for data collection, automated experiment execution, closed-loop control, and so forth, data processing and display axe done with the SDDS Toolkit. Experiments and data reduction axe implemented as UNIX shell scripts that coordinate the execution of EPICS specific tools and SDDS tools. Because of the power and generic nature of the individual tools and of the UNIX shell environment, automated experiments can be prepared and executed rapidly in response to unanticipated needs or new ideas. Examples are given of application of this methodology to beam motion characterization, beam-position-monitor offset measurements, and klystron characterization

  3. Pierre Gy's sampling theory and sampling practice heterogeneity, sampling correctness, and statistical process control

    CERN Document Server

    Pitard, Francis F

    1993-01-01

    Pierre Gy's Sampling Theory and Sampling Practice, Second Edition is a concise, step-by-step guide for process variability management and methods. Updated and expanded, this new edition provides a comprehensive study of heterogeneity, covering the basic principles of sampling theory and its various applications. It presents many practical examples to allow readers to select appropriate sampling protocols and assess the validity of sampling protocols from others. The variability of dynamic process streams using variography is discussed to help bridge sampling theory with statistical process control. Many descriptions of good sampling devices, as well as descriptions of poor ones, are featured to educate readers on what to look for when purchasing sampling systems. The book uses its accessible, tutorial style to focus on professional selection and use of methods. The book will be a valuable guide for mineral processing engineers; metallurgists; geologists; miners; chemists; environmental scientists; and practit...

  4. Temperature Control Diagnostics for Sample Environments

    International Nuclear Information System (INIS)

    Santodonato, Louis J.; Walker, Lakeisha M.H.; Church, Andrew J.; Redmon, Christopher Mckenzie

    2010-01-01

    In a scientific laboratory setting, standard equipment such as cryocoolers are often used as part of a custom sample environment system designed to regulate temperature over a wide range. The end user may be more concerned with precise sample temperature control than with base temperature. But cryogenic systems tend to be specified mainly in terms of cooling capacity and base temperature. Technical staff at scientific user facilities (and perhaps elsewhere) often wonder how to best specify and evaluate temperature control capabilities. Here we describe test methods and give results obtained at a user facility that operates a large sample environment inventory. Although this inventory includes a wide variety of temperature, pressure, and magnetic field devices, the present work focuses on cryocooler-based systems.

  5. Automated sampling and control of gaseous simulations

    KAUST Repository

    Huang, Ruoguan

    2013-05-04

    In this work, we describe a method that automates the sampling and control of gaseous fluid simulations. Several recent approaches have provided techniques for artists to generate high-resolution simulations based on a low-resolution simulation. However, often in applications the overall flow in the low-resolution simulation that an animator observes and intends to preserve is composed of even lower frequencies than the low resolution itself. In such cases, attempting to match the low-resolution simulation precisely is unnecessarily restrictive. We propose a new sampling technique to efficiently capture the overall flow of a fluid simulation, at the scale of user\\'s choice, in such a way that the sampled information is sufficient to represent what is virtually perceived and no more. Thus, by applying control based on the sampled data, we ensure that in the resulting high-resolution simulation, the overall flow is matched to the low-resolution simulation and the fine details on the high resolution are preserved. The samples we obtain have both spatial and temporal continuity that allows smooth keyframe matching and direct manipulation of visible elements such as smoke density through temporal blending of samples. We demonstrate that a user can easily configure a simulation with our system to achieve desired results. © 2013 Springer-Verlag Berlin Heidelberg.

  6. EPIC: an Error Propagation/Inquiry Code

    International Nuclear Information System (INIS)

    Baker, A.L.

    1985-01-01

    The use of a computer program EPIC (Error Propagation/Inquiry Code) will be discussed. EPIC calculates the variance of a materials balance closed about a materials balance area (MBA) in a processing plant operated under steady-state conditions. It was designed for use in evaluating the significance of inventory differences in the Department of Energy (DOE) nuclear plants. EPIC rapidly estimates the variance of a materials balance using average plant operating data. The intent is to learn as much as possible about problem areas in a process with simple straightforward calculations assuming a process is running in a steady-state mode. EPIC is designed to be used by plant personnel or others with little computer background. However, the user should be knowledgeable about measurement errors in the system being evaluated and have a limited knowledge of how error terms are combined in error propagation analyses. EPIC contains six variance equations; the appropriate equation is used to calculate the variance at each measurement point. After all of these variances are calculated, the total variance for the MBA is calculated using a simple algebraic sum of variances. The EPIC code runs on any computer that accepts a standard form of the BASIC language. 2 refs., 1 fig., 6 tabs

  7. Getting DNA copy numbers without control samples

    Directory of Open Access Journals (Sweden)

    Ortiz-Estevez Maria

    2012-08-01

    Full Text Available Abstract Background The selection of the reference to scale the data in a copy number analysis has paramount importance to achieve accurate estimates. Usually this reference is generated using control samples included in the study. However, these control samples are not always available and in these cases, an artificial reference must be created. A proper generation of this signal is crucial in terms of both noise and bias. We propose NSA (Normality Search Algorithm, a scaling method that works with and without control samples. It is based on the assumption that genomic regions enriched in SNPs with identical copy numbers in both alleles are likely to be normal. These normal regions are predicted for each sample individually and used to calculate the final reference signal. NSA can be applied to any CN data regardless the microarray technology and preprocessing method. It also finds an optimal weighting of the samples minimizing possible batch effects. Results Five human datasets (a subset of HapMap samples, Glioblastoma Multiforme (GBM, Ovarian, Prostate and Lung Cancer experiments have been analyzed. It is shown that using only tumoral samples, NSA is able to remove the bias in the copy number estimation, to reduce the noise and therefore, to increase the ability to detect copy number aberrations (CNAs. These improvements allow NSA to also detect recurrent aberrations more accurately than other state of the art methods. Conclusions NSA provides a robust and accurate reference for scaling probe signals data to CN values without the need of control samples. It minimizes the problems of bias, noise and batch effects in the estimation of CNs. Therefore, NSA scaling approach helps to better detect recurrent CNAs than current methods. The automatic selection of references makes it useful to perform bulk analysis of many GEO or ArrayExpress experiments without the need of developing a parser to find the normal samples or possible batches within the

  8. Getting DNA copy numbers without control samples.

    Science.gov (United States)

    Ortiz-Estevez, Maria; Aramburu, Ander; Rubio, Angel

    2012-08-16

    The selection of the reference to scale the data in a copy number analysis has paramount importance to achieve accurate estimates. Usually this reference is generated using control samples included in the study. However, these control samples are not always available and in these cases, an artificial reference must be created. A proper generation of this signal is crucial in terms of both noise and bias.We propose NSA (Normality Search Algorithm), a scaling method that works with and without control samples. It is based on the assumption that genomic regions enriched in SNPs with identical copy numbers in both alleles are likely to be normal. These normal regions are predicted for each sample individually and used to calculate the final reference signal. NSA can be applied to any CN data regardless the microarray technology and preprocessing method. It also finds an optimal weighting of the samples minimizing possible batch effects. Five human datasets (a subset of HapMap samples, Glioblastoma Multiforme (GBM), Ovarian, Prostate and Lung Cancer experiments) have been analyzed. It is shown that using only tumoral samples, NSA is able to remove the bias in the copy number estimation, to reduce the noise and therefore, to increase the ability to detect copy number aberrations (CNAs). These improvements allow NSA to also detect recurrent aberrations more accurately than other state of the art methods. NSA provides a robust and accurate reference for scaling probe signals data to CN values without the need of control samples. It minimizes the problems of bias, noise and batch effects in the estimation of CNs. Therefore, NSA scaling approach helps to better detect recurrent CNAs than current methods. The automatic selection of references makes it useful to perform bulk analysis of many GEO or ArrayExpress experiments without the need of developing a parser to find the normal samples or possible batches within the data. The method is available in the open-source R package

  9. Robust sampled-data control of hydraulic flight control actuators

    OpenAIRE

    Kliffken, Markus Gustav

    1997-01-01

    In todays flight-by-wire systems the primary flight control surfaces of modern commercial and transport aircraft are driven by electro hydraulic linear actuators. Changing flight conditions as well as nonlinear actuator dynamics may be interpreted as parameter uncertainties of the linear actuator model. This demands a robust design for the controller. Here the parameter space design is used for the direct sampled-data controller synthesis. Therefore, a static output controller is choosen, the...

  10. SNS online display technologies for EPICS

    International Nuclear Information System (INIS)

    Kasemir, K.U.; Chen, X.; Purcell, J.; Danilova, E.

    2012-01-01

    The ubiquitousness of web clients from personal computers to cell phones results in a growing demand for web-based access to control system data. At the Oak Ridge National Laboratory Spallation Neutron Source (SNS) we have investigated different technical approaches to provide read access to data in the Experimental Physics and Industrial Control System (EPICS) for a wide variety of web client devices. The core web technology, HTTP, is less than ideal for online control system displays. Appropriate use of Ajax, especially the Long Poll paradigm, can alleviate fundamental HTTP limitations. The SNS Status web uses basic Ajax technology to generate generic displays for a wide audience. The Dashboard uses Long Poll and more client-side Java-Script to offer more customization and faster updates for users that need specialized displays. The Web OPI uses RAP for web access to any BOY display, offering utmost flexibility because users can create their own BOY displays in CSS. These three approaches complement each other. Users can access generic status displays with zero effort, invest time in creating their fully customized displays for the Web OPI, or use the Dashboard as an intermediate solution

  11. Hyperarchiver: an evolution of EPICS channel archiver

    International Nuclear Information System (INIS)

    Campo, M. del; Arredondo, I.; Jugo, J.; Giacchini, M.; Giovannini, L.

    2012-01-01

    Data storage is a primary issue in any research facility. In the EPICS middleware based accelerator community, Channel Archiver has been always considered the main reference. It works with Oracle and MySQL, probably the best well known relational databases. However, demanding requirements at minimum costs have fostered the development of a wide range of alternatives, like MDSPlus (Consorzio RFX), SciDB (BNL) or Hypertable (IFNF). This document launches a tool called HyperArchiver, which was firstly developed at IFNF (Italy) and eventually customised by ESS Bilbao (Spain). Based on a NoSQL database named Hypertable, it focuses on large data sets management with maximum scalability, reliability and performance. Besides the update and further customization made at ESS Bilbao, HyperArchiver is presented with a set of GUIs, in order to provide an easy use and integration with any general control system. A LabVIEW VI and two cross-platform PyQt GUIs for both Hypertable data retrieval and HyperArchiver control have been developed and successfully tested at ESS Bilbao. (author)

  12. Collaborative development of the EPICS Qt framework Phase I Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Mayssat, Robert E. [Lyncean Technologies, Inc., Palo Alto, CA (United States)

    2015-01-15

    At Lyncean, a private company spun-off from technology developed at the SLAC National Lab, we have been using EPICS for over a decade. EPICS is ubiquitous on our flagship product – the Compact Light Source. EPICS is not only used to control our laser and accelerator systems, but also to control our x-ray beamlines. The goal of this SBIR is for Lyncean Technologies to spearhead a worldwide collaborative effort for the development of control system tools for EPICS using the Qt framework, a C++-based coding environment that could serve as a competitive alternative to the Java-based Control System Studio (CSS). This grant's Phase I, not unlike a feasibility study, is designed for planning and scoping the preparatory work needed for Phase II or other funding opportunities. The three main objectives of this Phase I are (1) to become better acquainted with the existing EPICS Qt software and Qt framework in order to evaluate the best options for ongoing development, (2) to demonstrate that our engineers can lead the EPICS community and jump-start the Qt collaboration, and (3) to identify a scope for our future work with solicited feedback from the EPICS community. This Phase I report includes key technical findings. It clarifies the differences between the two apparently-competing EPICS Qt implementations, caQtDM and the QE Framework; it explains how to create python-bindings, and compares Qt graphical libraries. But this report is also a personal story that narrates the birth of a collaboration. Starting a collaboration is not the work of a single individual, but the work of many. Therefore this report is also an attempt to publicly give credit to many who supported the effort. The main take-away from this grant is the successful birth of an EPICS Qt collaboration, seeded with existing software from the PSI and the Australian Synchrotron. But a lot more needs to be done for the collaboration founders' vision to be realized, and for the collaboration to reach

  13. Quality assurance of the international computerised 24 h dietary recall method (EPIC-Soft).

    Science.gov (United States)

    Crispim, Sandra P; Nicolas, Genevieve; Casagrande, Corinne; Knaze, Viktoria; Illner, Anne-Kathrin; Huybrechts, Inge; Slimani, Nadia

    2014-02-01

    The interview-administered 24 h dietary recall (24-HDR) EPIC-Soft® has a series of controls to guarantee the quality of dietary data across countries. These comprise all steps that are part of fieldwork preparation, data collection and data management; however, a complete characterisation of these quality controls is still lacking. The present paper describes in detail the quality controls applied in EPIC-Soft, which are, to a large extent, built on the basis of the EPIC-Soft error model and are present in three phases: (1) before, (2) during and (3) after the 24-HDR interviews. Quality controls for consistency and harmonisation are implemented before the interviews while preparing the seventy databases constituting an EPIC-Soft version (e.g. pre-defined and coded foods and recipes). During the interviews, EPIC-Soft uses a cognitive approach by helping the respondent to recall the dietary intake information in a stepwise manner and includes controls for consistency (e.g. probing questions) as well as for completeness of the collected data (e.g. system calculation for some unknown amounts). After the interviews, a series of controls can be applied by dietitians and data managers to further guarantee data quality. For example, the interview-specific 'note files' that were created to track any problems or missing information during the interviews can be checked to clarify the information initially provided. Overall, the quality controls employed in the EPIC-Soft methodology are not always perceivable, but prove to be of assistance for its overall standardisation and possibly for the accuracy of the collected data.

  14. DOE's Pollution Prevention Information Clearinghouse (EPIC)

    International Nuclear Information System (INIS)

    Otis, P.T.

    1994-05-01

    The US Department of Energy's (DOE's) Pollution Prevention Information Clearinghouse (EPIC) is a computer system intended for the exchange of pollution prevention information DOE-wide. EPIC is being developed as a distributed system that will allow access to other databases and applications. The first prototype of EPIC (Prototype I) was put on-line in January 1994. Prototype I contains information on EM-funded pollution prevention projects; relevant laws, regulations, guidance, and policy; facility and DOE contacts; and meetings and conferences. Prototype I also gives users access to the INEL Hazardous Solvent Substitution Data System (HSSDS) and to information contained on the US Environmental Protection Agency's (EPNS) Pollution Prevention Infbrmation Exchange System (PIES) as a test of the distributed system concept. An initial user group of about 35 is testing and providing feedback on Prototype I. Prototype II, with a Graphical User Interface (GUI), is planned for the end of CY94. This paper describes the current state of EPIC in terms of architecture, user interface, and information content. Plans for Prototype II and the final system are then discussed. The EPIC development effort is being coordinated with EPA and US Department of Defense (DoD) efforts to develop or upgrade their pollution prevention information exchange systems

  15. Development of EPICS channel access embedded ActiveX components for GUI development

    International Nuclear Information System (INIS)

    Roy, A.; Bhole, R.B.; Pal, S.

    2012-01-01

    The paper describes the integration of Experimental Physics and Industrial Control System (EPICS) Channel Access (CA) protocol and Microsoft ActiveX technology towards developing a generalize operator interface (OPI) building facility for Windows platform. EPICS is used as the development architecture of the control system in Superconducting Cyclotron (SCC). Considering the operators' familiarity and compatibility with third party software, it was decided to use MS-Windows platform at operator interface level in SCC during commission. Microsoft Visual Basic (VB) is used on trial basis as OPI building platform to incorporate user specific features e.g. file system access for data storage and analysis, user authentication at OPI level etc. A set of EPICS Channel Access embedded ActiveX components is developed to ease the programming complexity and reduce developmental time of the OPI for Windows platform. OPIs, developed using these components and containing hundreds of process parameters, are being used reliably over a considerable period of time. (author)

  16. Study of 3D visualization of fast active reflector based on openGL and EPICS

    International Nuclear Information System (INIS)

    Luo Mingcheng; Wu Wenqing; Liu Jiajing; Tang Pengyi; Wang Jian

    2014-01-01

    Active Reflector is the one of the innovations of Five hundred meter Aperture Spherical Telescope (FAST). Its performance will influence the performance of whole telescope and for display all status of ARS in real time, the EPICS (Experimental Physics and Industrial Control System) is used to develop the control system of ARS and virtual 3D technology-OpenGL is used to visualize the status. For the real-time performance of EPICS, the status visualization is also display in real time for users to improve the efficiency of telescope observing. (authors)

  17. 21 CFR 203.38 - Sample lot or control numbers; labeling of sample units.

    Science.gov (United States)

    2010-04-01

    ... numbers; labeling of sample units. (a) Lot or control number required on drug sample labeling and sample... identifying lot or control number that will permit the tracking of the distribution of each drug sample unit... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Sample lot or control numbers; labeling of sample...

  18. 77 FR 73655 - Epic Marketplace, Inc., and Epic Media Group, LLC; Analysis of Proposed Consent Order To Aid...

    Science.gov (United States)

    2012-12-11

    ... action or make final the agreement's proposed order. Epic Marketplace, Inc. (``Epic'') is an advertising company that engages in online behavioral advertising, which is the practice of tracking a consumer's online activities in order to deliver advertising targeted to the consumer's interests. Epic is a wholly...

  19. HyperArchiver: an EPICS archiver prototype based on Hypertable

    International Nuclear Information System (INIS)

    Giacchini, M.; Giovannini, L.; Montis, M.; Bassato, G.; Vasquez, J.A.; Prete, G.; Andrighetto, A.; Petkus, R.; Lange, R.; Kasemir, K.; Del Campo, M.; Jugo, J.

    2012-01-01

    This work started in the context of NSLS2 project at Brookhaven National Laboratory. The NSLS2 control system foresees a very high number of PV variables and has strict requirements in terms of archiving/retrieving rate: our goal was to store 10 K PV/sec and retrieve 4 K PV/sec for a group of 4 signals. The HyperArchiver is an EPICS Archiver implementation engined by Hypertable, an open source database whose internal architecture is derived from Google's Big Table. We discuss the performance of HyperArchiver and present the results of some comparative tests. (authors)

  20. European Prospective Investigation into Cancer and Nutrition (EPIC): study populations and data collection

    DEFF Research Database (Denmark)

    Riboli, E.; Hunt, K.J.; Slimani, N.

    2002-01-01

    , mostly in liquid nitrogen. To calibrate dietary measurements, a standardised, computer-assisted 24-hour dietary recall was implemented at each centre on stratified random samples of the participants, for a total of 36 900 subjects. EPIC represents the largest single resource available today world...

  1. Education for Change: Epic Charter School

    Science.gov (United States)

    EDUCAUSE, 2015

    2015-01-01

    The student-centered school model of Epic Charter School in Oakland, California, framed around a hero's journey empowers middle school students with sense of unity and purpose in life, where they can feel part of a culture with a shared experience and with more opportunities to experiences growth and accomplishment. Design and engineering is front…

  2. The coal epic at Freyming-Merlebach

    International Nuclear Information System (INIS)

    2003-01-01

    This information document has been realized on the closure of the Merlebach site. It is devoted to the coal epic at Freyming-Merlebach. The historical aspects of the exploitation, the working conditions, the economic and environmental aspects of the mine and the today situation are detailed. (A.L.B.)

  3. Preliminary design and integration of EPICS operation interface for the Taiwan photon source

    International Nuclear Information System (INIS)

    Cheng, Y.S.; Jenny Chen; Chiu, P.C.; Kuo, C.H.; Liao, C.Y.; Hsu, K.T.; Wu, C.Y.

    2012-01-01

    The TPS (Taiwan Photon Source) is the latest generation 3 GeV synchrotron light source which has been in construction since 2010. The EPICS (Experimental Physics and Industrial Control System) framework is adopted as control system infrastructure for the TPS. The EPICS IOCs (Input Output Controller) and various database records have been gradually implemented to control and monitor available subsystems of the TPS at this moment. The subsystem includes timing, power supply, motion controller, miscellaneous Ethernet compliant devices etc. Through EPICS PVs (Process Variables) channel access, remote access I/O data via Ethernet interface can be observed by the usable graphical tool-kits, such as the EDM (Extensible Display Manager) and MATLAB. The operation interface mainly includes the function of setting, reading, save, restore and etc. Integration of operation interfaces will depend upon properties of each subsystem. In addition, the centralized management method is utilized to serve every client from file servers in order to maintain consistent versions of related EPICS files. (authors)

  4. Design and Implementation of a Web-based Monitoring System by using EPICS Channel Access Protocol

    International Nuclear Information System (INIS)

    An, Eun Mi; Song, Yong Gi

    2009-01-01

    Proton Engineering Frontier Project (PEFP) has developed a 20MeV proton accelerator, and established a distributed control system based on EPICS for sub-system components such as vacuum unit, beam diagnostics, and power supply system. The control system includes a real-time monitoring and alarm functions. From the aspect of a efficient maintenance of a control system and a additional extension of subsystems, EPICS software framework was adopted. In addition, a control system should be capable of providing an easy access for users and a real-time monitoring on a user screen. Therefore, we have implemented a new web-based monitoring server with several libraries. By adding DB module, the new IOC web monitoring system makes it possible to monitor the system through the web. By integrating EPICS Channel Access (CA) and Database libraries into a Database module, the web-based monitoring system makes it possible to monitor the sub-system status through user's internet browser. In this study, we developed a web based monitoring system by using EPICS IOC (Input Output Controller) with IBM server

  5. ISAC EPICS on Linux: the march of the penguins

    International Nuclear Information System (INIS)

    Richards, J.; Nussbaumer, R.; Rapaz, S.; Waters, G.

    2012-01-01

    The DC linear accelerators of the ISAC radioactive beam facility at TRIUMF do not impose rigorous timing constraints on the control system. Therefore a real-time operating system is not essential for device control. The ISAC Control System is completing a move to the use of the Linux operating system for hosting all EPICS IOCs. The IOC platforms include GE-Fanuc VME based CPUs for control of most optics and diagnostics, rack mounted servers for supervising PLCs, small desktop PCs for GPIB and RS232 instruments, as well as embedded ARM processors controlling CAN-bus devices that provide a suitcase sized control system. This article focuses on the experience of creating a customized Linux distribution for front-end IOC deployment. Rationale, a road-map of the process, and efficiency advantages in personnel training and system management realized by using a single OS will be discussed. (authors)

  6. Flight Vehicle Control and Aerobiological Sampling Applications

    OpenAIRE

    Techy, Laszlo

    2009-01-01

    Aerobiological sampling using unmanned aerial vehicles (UAVs) is an exciting research field blending various scientific and engineering disciplines. The biological data collected using UAVs helps to better understand the atmospheric transport of microorganisms. Autopilot-equipped UAVs can accurately sample along pre-defined flight plans and precisely regulated altitudes. They can provide even greater utility when they are networked together in coordinated sampling missions: such measurements ...

  7. [Dietary habits and cancer: the experience of EPIC-Italy].

    Science.gov (United States)

    Sieri, Sabina; Agnoli, Claudia; Pala, Valeria; Mattiello, Amalia; Panico, Salvatore; Masala, Giovanna; Assedi, Melania; Tumino, Rosario; Frasca, Graziella; Sacerdote, Carlotta; Vineis, Paolo; Krogh, Vittorio

    2015-01-01

    to investigate hypothesised relationships between diet and cancer by assessing diet as a whole, in the Italian cohort EPIC. multicentric prospective study. 47,749 volunteers were recruited between 1993 and 1998 in the centres of Varese and Turin (Northern Italy), Florence (Central Italy), Naples and Ragusa (Southern Italy). Information on diet and lifestyle were collected through validated questionnaires. Anthropometric measurements were taken and biological samples collected using standardised protocols. follow-up was carried out by accessing regional cancer and mortality registries, hospital discharge records, and by telephone inquiries (only for Naples). After a median follow-up of 11 years, 879 incident cases of breast cancer, 421 cases of colorectal cancer, and 152 deaths were identified. Multivariate Cox regression models were used to estimate risks in relation to dietary characteristics. the "Olive oil & Salad" dietary pattern, characterised by high consumption of raw vegetables and olive oil, was associated with a lower risk of overall mortality in the elderly. Adherence to a Mediterranean diet rich in vegetables and fruit was associated with reduced risk of colon cancer. Consumption of high-glycemic carbohydrates was associated with higher incidence of breast cancer and colorectal cancer. Reduced risk of colon cancer was also found in regular consumers of yoghurt. the accuracy and comprehensiveness of EPIC-Italy data made it possible to investigate both individual dietary components and dietary habits as a whole, to thereby provide Italians with dietary and lifestyle advice that will help them to remain healthy.

  8. Calibration of the DSCOVR EPIC visible and NIR channels using MODIS Terra and Aqua data and EPIC lunar observations

    Directory of Open Access Journals (Sweden)

    I. V. Geogdzhayev

    2018-01-01

    Full Text Available The unique position of the Deep Space Climate Observatory (DSCOVR Earth Polychromatic Imaging Camera (EPIC at the Lagrange 1 point makes an important addition to the data from currently operating low Earth orbit observing instruments. EPIC instrument does not have an onboard calibration facility. One approach to its calibration is to compare EPIC observations to the measurements from polar-orbiting radiometers. Moderate Resolution Imaging Spectroradiometer (MODIS is a natural choice for such comparison due to its well-established calibration record and wide use in remote sensing. We use MODIS Aqua and Terra L1B 1 km reflectances to infer calibration coefficients for four EPIC visible and NIR channels: 443, 551, 680 and 780 nm. MODIS and EPIC measurements made between June 2015 and 2016 are employed for comparison. We first identify favorable MODIS pixels with scattering angle matching temporarily collocated EPIC observations. Each EPIC pixel is then spatially collocated to a subset of the favorable MODIS pixels within 25 km radius. Standard deviation of the selected MODIS pixels as well as of the adjacent EPIC pixels is used to find the most homogeneous scenes. These scenes are then used to determine calibration coefficients using a linear regression between EPIC counts s−1 and reflectances in the close MODIS spectral channels. We present thus inferred EPIC calibration coefficients and discuss sources of uncertainties. The lunar EPIC observations are used to calibrate EPIC O2 absorbing channels (688 and 764 nm, assuming that there is a small difference between moon reflectances separated by  ∼  10 nm in wavelength and provided the calibration factors of the red (680 nm and NIR (780 nm are known from comparison between EPIC and MODIS.

  9. Calibration of the DSCOVR EPIC Visible and NIR Channels using MODIS Terra and Aqua Data and EPIC Lunar Observations

    Science.gov (United States)

    Geogdzhayev, Igor V.; Marshak, Alexander

    2018-01-01

    The unique position of the Deep Space Climate Observatory (DSCOVR) Earth Polychromatic Imaging Camera (EPIC) at the Lagrange 1 point makes an important addition to the data from currently operating low Earth orbit observing instruments. EPIC instrument does not have an onboard calibration facility. One approach to its calibration is to compare EPIC observations to the measurements from polar-orbiting radiometers. Moderate Resolution Imaging Spectroradiometer (MODIS) is a natural choice for such comparison due to its well-established calibration record and wide use in remote sensing. We use MODIS Aqua and Terra L1B 1km reflectances to infer calibration coefficients for four EPIC visible and NIR channels: 443, 551, 680 and 780 nm. MODIS and EPIC measurements made between June 2015 and 2016 are employed for comparison. We first identify favorable MODIS pixels with scattering angle matching temporarily collocated EPIC observations. Each EPIC pixel is then spatially collocated to a subset of the favorable MODIS pixels within 25 km radius. Standard deviation of the selected MODIS pixels as well as of the adjacent EPIC pixels is used to find the most homogeneous scenes. These scenes are then used to determine calibration coefficients using a linear regression between EPIC counts/sec and reflectances in the close MODIS spectral channels. We present thus inferred EPIC calibration coefficients and discuss sources of uncertainties. The lunar EPIC observations are used to calibrate EPIC O2 absorbing channels (688 and 764 nm), assuming that there is a small difference between moon reflectances separated by approx.10 nm in wavelength provided the calibration factors of the red (680 nm) and near-IR (780 nm) are known from comparison between EPIC and MODIS.

  10. Controlling Sample Rotation in Acoustic Levitation

    Science.gov (United States)

    Barmatz, M. B.; Stoneburner, J. D.

    1985-01-01

    Rotation of acoustically levitated object stopped or controlled according to phase-shift monitoring and control concept. Principle applies to square-cross-section levitation chamber with two perpendicular acoustic drivers operating at same frequency. Phase difference between X and Y acoustic excitation measured at one corner by measuring variation of acoustic amplitude sensed by microphone. Phase of driver adjusted to value that produces no rotation or controlled rotation of levitated object.

  11. Enlisted Personnel Individualized Career System (EPICS) Test and Evaluation

    Science.gov (United States)

    1984-01-01

    The EPICS program, which was developed using an integrated personnel systems approach ( IPSA ), delays formal school training until after personnel have...received shipboard on-job training complemented by job performance aids (3PAs). Early phases of the program, which involved developing the IPSA EPICS...detailed description of the conception and development of the EPICS IPSA model, the execution of the front-end job design analyses, 3PA and instructional

  12. ATCA Shelf Manager EPICS device support for ITER CODAC Core System

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Bruno, E-mail: bsantos@ipfn.ist.utl.pt [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Carvalho, Paulo F.; Rodrigues, A.P.; Carvalho, Bernardo B.; Sousa, Jorge; Batista, António J.N.; Correia, Miguel; Combo, Álvaro M.; Cruz, Nuno [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Correia, Carlos M.B.A. [Centro de Instrumentação, Departamento de Física, Universidade de Coimbra, 3004-516 Coimbra (Portugal); Gonçalves, Bruno [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal)

    2015-10-15

    Highlights: • This architecture targets the health management integration into the NDS. • The developed solution supports the ShM redundancy features, specified by ATCA. • The average RTT was around 59 ms and in 99.9% of the cases was less than 130 ms. • Without losing any update cycle, can monitor a system shelf with approximately 400 sensors. • This solution enables the user to configure the entire system in DB files and st.cmd. - Abstract: The ITER CODAC Core System (CCS) is responsible for plant Instrumentation and Control (I&C) supervising and monitoring. This system uses the Enhanced Physics and Industrial Control System (EPICS) Channel Access (CA) protocol as the interface with the Plant Operation Network (PON). This paper presents a generic EPICS device support developed for the integration of the ATCA Shelf Manager (ShM) into the ITER CCS, providing scalability and easy configuration. The device support uses the available HTTP interface on Shelf Manager in the communication layer. Both HTTP server and sensors/actuators definitions can be configured using the EPICS database file and the Input/Output Controller (IOC) initialization file. A proposal based on this device is also presented, targeting the Nominal Device Support (NDS) for health management. The EPICS device support running in an IOC provides Process Variables (PV) to the PON network with the system information and these PVs can be used by all CA clients, such as EPICS user interface clients, alarm systems and archive systems. Operation with redundant ATCA ShMs and device support scalability tests were performed and the results are presented.

  13. Control charts for location based on different sampling schemes

    NARCIS (Netherlands)

    Mehmood, R.; Riaz, M.; Does, R.J.M.M.

    2013-01-01

    Control charts are the most important statistical process control tool for monitoring variations in a process. A number of articles are available in the literature for the X̄ control chart based on simple random sampling, ranked set sampling, median-ranked set sampling (MRSS), extreme-ranked set

  14. Nutrient patterns and their food sources in an International Study Setting: report from the EPIC study.

    Science.gov (United States)

    Moskal, Aurelie; Pisa, Pedro T; Ferrari, Pietro; Byrnes, Graham; Freisling, Heinz; Boutron-Ruault, Marie-Christine; Cadeau, Claire; Nailler, Laura; Wendt, Andrea; Kühn, Tilman; Boeing, Heiner; Buijsse, Brian; Tjønneland, Anne; Halkjær, Jytte; Dahm, Christina C; Chiuve, Stephanie E; Quirós, Jose R; Buckland, Genevieve; Molina-Montes, Esther; Amiano, Pilar; Huerta Castaño, José M; Gurrea, Aurelio Barricarte; Khaw, Kay-Tee; Lentjes, Marleen A; Key, Timothy J; Romaguera, Dora; Vergnaud, Anne-Claire; Trichopoulou, Antonia; Bamia, Christina; Orfanos, Philippos; Palli, Domenico; Pala, Valeria; Tumino, Rosario; Sacerdote, Carlotta; de Magistris, Maria Santucci; Bueno-de-Mesquita, H Bas; Ocké, Marga C; Beulens, Joline W J; Ericson, Ulrika; Drake, Isabel; Nilsson, Lena M; Winkvist, Anna; Weiderpass, Elisabete; Hjartåker, Anette; Riboli, Elio; Slimani, Nadia

    2014-01-01

    Compared to food patterns, nutrient patterns have been rarely used particularly at international level. We studied, in the context of a multi-center study with heterogeneous data, the methodological challenges regarding pattern analyses. We identified nutrient patterns from food frequency questionnaires (FFQ) in the European Prospective Investigation into Cancer and Nutrition (EPIC) Study and used 24-hour dietary recall (24-HDR) data to validate and describe the nutrient patterns and their related food sources. Associations between lifestyle factors and the nutrient patterns were also examined. Principal component analysis (PCA) was applied on 23 nutrients derived from country-specific FFQ combining data from all EPIC centers (N = 477,312). Harmonized 24-HDRs available for a representative sample of the EPIC populations (N = 34,436) provided accurate mean group estimates of nutrients and foods by quintiles of pattern scores, presented graphically. An overall PCA combining all data captured a good proportion of the variance explained in each EPIC center. Four nutrient patterns were identified explaining 67% of the total variance: Principle component (PC) 1 was characterized by a high contribution of nutrients from plant food sources and a low contribution of nutrients from animal food sources; PC2 by a high contribution of micro-nutrients and proteins; PC3 was characterized by polyunsaturated fatty acids and vitamin D; PC4 was characterized by calcium, proteins, riboflavin, and phosphorus. The nutrients with high loadings on a particular pattern as derived from country-specific FFQ also showed high deviations in their mean EPIC intakes by quintiles of pattern scores when estimated from 24-HDR. Center and energy intake explained most of the variability in pattern scores. The use of 24-HDR enabled internal validation and facilitated the interpretation of the nutrient patterns derived from FFQs in term of food sources. These outcomes open research opportunities and

  15. Nutrient patterns and their food sources in an International Study Setting: report from the EPIC study.

    Directory of Open Access Journals (Sweden)

    Aurelie Moskal

    Full Text Available Compared to food patterns, nutrient patterns have been rarely used particularly at international level. We studied, in the context of a multi-center study with heterogeneous data, the methodological challenges regarding pattern analyses.We identified nutrient patterns from food frequency questionnaires (FFQ in the European Prospective Investigation into Cancer and Nutrition (EPIC Study and used 24-hour dietary recall (24-HDR data to validate and describe the nutrient patterns and their related food sources. Associations between lifestyle factors and the nutrient patterns were also examined. Principal component analysis (PCA was applied on 23 nutrients derived from country-specific FFQ combining data from all EPIC centers (N = 477,312. Harmonized 24-HDRs available for a representative sample of the EPIC populations (N = 34,436 provided accurate mean group estimates of nutrients and foods by quintiles of pattern scores, presented graphically. An overall PCA combining all data captured a good proportion of the variance explained in each EPIC center. Four nutrient patterns were identified explaining 67% of the total variance: Principle component (PC 1 was characterized by a high contribution of nutrients from plant food sources and a low contribution of nutrients from animal food sources; PC2 by a high contribution of micro-nutrients and proteins; PC3 was characterized by polyunsaturated fatty acids and vitamin D; PC4 was characterized by calcium, proteins, riboflavin, and phosphorus. The nutrients with high loadings on a particular pattern as derived from country-specific FFQ also showed high deviations in their mean EPIC intakes by quintiles of pattern scores when estimated from 24-HDR. Center and energy intake explained most of the variability in pattern scores.The use of 24-HDR enabled internal validation and facilitated the interpretation of the nutrient patterns derived from FFQs in term of food sources. These outcomes open research

  16. EPIC: A Framework for Using Video Games in Ethics Education

    Science.gov (United States)

    Schrier, Karen

    2015-01-01

    Ethics education can potentially be supplemented through the use of video games. This article proposes a novel framework (Ethics Practice and Implementation Categorization [EPIC] Framework), which helps educators choose games to be used for ethics education purposes. The EPIC Framework is derived from a number of classic moral development,…

  17. Design for Change : EPIC pillars for Persuasive Design for Health

    NARCIS (Netherlands)

    Tjin-Kam-Jet-Siemons, Liseth; van Gemert-Pijnen, Julia E.W.C.

    2016-01-01

    What makes technology now truly empathic? How to develop designs that matter? We apply the EPIC for change model for persuasive and empathic designs. EPIC stands for: • Engagement: Creating experience, flow using persuasive strategies and triggers in development, using positive psychology concepts;

  18. EPIC: Helping School Life and Family Support Each Other.

    Science.gov (United States)

    Montgomery, David

    1992-01-01

    Born out of a 1981 murder, Buffalo (New York) Public Schools' EPIC (Effective Parenting Information for Children) program successfully combines parenting, effective teaching, and community programs to help family and school life support each other. Under EPIC, teachers are advised to help students acquire 23 skills involving self-esteem, rules,…

  19. Perfusion Electronic Record Documentation Using Epic Systems Software.

    Science.gov (United States)

    Riley, Jeffrey B; Justison, George A

    2015-12-01

    The authors comment on Steffens and Gunser's article describing the University of Wisconsin adoption of the Epic anesthesia record to include perfusion information from the cardiopulmonary bypass patient experience. We highlight the current-day lessons and the valuable quality and safety principles the Wisconsin-Epic model anesthesia-perfusion record provides.

  20. The improved physical activity index for measuring physical activity in EPIC Germany.

    Science.gov (United States)

    Wientzek, Angelika; Vigl, Matthäus; Steindorf, Karen; Brühmann, Boris; Bergmann, Manuela M; Harttig, Ulrich; Katzke, Verena; Kaaks, Rudolf; Boeing, Heiner

    2014-01-01

    In the European Investigation into Cancer and Nutrition study (EPIC), physical activity (PA) has been indexed as a cross-tabulation between PA at work and recreational activity. As the proportion of non-working participants increases, other categorization strategies are needed. Therefore, our aim was to develop a valid PA index for this population, which will also be able to express PA continuously. In the German EPIC centers Potsdam and Heidelberg, a clustered sample of 3,766 participants was re-invited to the study center. 1,615 participants agreed to participate and 1,344 participants were finally included in this study. PA was measured by questionnaires on defined activities and a 7-day combined heart rate and acceleration sensor. In a training sample of 433 participants, the Improved Physical Activity Index (IPAI) was developed. Its performance was evaluated in a validation sample of 911 participants and compared with the Cambridge Index and the Total PA Index. The IPAI consists of items covering five areas including PA at work, sport, cycling, television viewing, and computer use. The correlations of the IPAI with accelerometer counts in the training and validation sample ranged r = 0.40-0.43 and with physical activity energy expenditure (PAEE) r = 0.33-0.40 and were higher than for the Cambridge Index and the Total PA Index previously applied in EPIC. In non-working participants the IPAI showed higher correlations than the Cambridge Index and the Total PA Index, with r = 0.34 for accelerometer counts and r = 0.29 for PAEE. In conclusion, we developed a valid physical activity index which is able to express PA continuously as well as to categorize participants according to their PA level. In populations with increasing rates of non-working people the performance of the IPAI is better than the established indices used in EPIC.

  1. The improved physical activity index for measuring physical activity in EPIC Germany.

    Directory of Open Access Journals (Sweden)

    Angelika Wientzek

    Full Text Available In the European Investigation into Cancer and Nutrition study (EPIC, physical activity (PA has been indexed as a cross-tabulation between PA at work and recreational activity. As the proportion of non-working participants increases, other categorization strategies are needed. Therefore, our aim was to develop a valid PA index for this population, which will also be able to express PA continuously. In the German EPIC centers Potsdam and Heidelberg, a clustered sample of 3,766 participants was re-invited to the study center. 1,615 participants agreed to participate and 1,344 participants were finally included in this study. PA was measured by questionnaires on defined activities and a 7-day combined heart rate and acceleration sensor. In a training sample of 433 participants, the Improved Physical Activity Index (IPAI was developed. Its performance was evaluated in a validation sample of 911 participants and compared with the Cambridge Index and the Total PA Index. The IPAI consists of items covering five areas including PA at work, sport, cycling, television viewing, and computer use. The correlations of the IPAI with accelerometer counts in the training and validation sample ranged r = 0.40-0.43 and with physical activity energy expenditure (PAEE r = 0.33-0.40 and were higher than for the Cambridge Index and the Total PA Index previously applied in EPIC. In non-working participants the IPAI showed higher correlations than the Cambridge Index and the Total PA Index, with r = 0.34 for accelerometer counts and r = 0.29 for PAEE. In conclusion, we developed a valid physical activity index which is able to express PA continuously as well as to categorize participants according to their PA level. In populations with increasing rates of non-working people the performance of the IPAI is better than the established indices used in EPIC.

  2. Study on the utilization of the cognitive architecture EPIC to the task analysis of a nuclear power plant operator

    International Nuclear Information System (INIS)

    Soares, Herculano Vieira

    2003-02-01

    This work presents a study of the use of the integrative cognitive architecture EPIC - Executive-Process - Interactive-Control, designed to evaluate the performance of a person performing tasks in parallel in a man-machine interface, as a methodology for Cognitive Task Analysis of a nuclear power plant operator. A comparison of the results obtained by the simulation by EPIC and the results obtained by application of the MHP model to the tasks performed by a shift operator during the execution of the procedure PO-E-3 - Steam Generator Tube Rupture of Angra 1 Nuclear Power Plant is done. To subsidize that comparison, an experiment was performed at the Angra 2 Nuclear Power Plant Full Scope Simulator in which three operator tasks were executed, its completion time measured and compared with the results of MHP and EPIC modeling. (author)

  3. Controlling a sample changer using the integrated counting system

    International Nuclear Information System (INIS)

    Deacon, S.; Stevens, M.P.

    1985-06-01

    Control of the Sample Changer from a counting system can be achieved by using a Scaler Timer type 6255 and Sample Changer Control Interface type 6263. The interface used, however, has quite complex circuitry. The application therefore lends itself to the use of another 6000 Series module the Integrated Counting System (ICS). Using this unit control is carried out through a control program written in BASIC for the Commodore PET (or any other device with an IEEE-488 interface). The ICS then controls the sample changer through an interface unit which is relatively simple. A brief description of how ICS controls the sample changer is given. The control program is then described, firstly the running options are given, followed by a program description listing and flowchart. (author)

  4. Controlling a sample changer using the integrated counting system

    Energy Technology Data Exchange (ETDEWEB)

    Deacon, S; Stevens, M P

    1985-06-01

    Control of the Sample Changer from a counting system can be achieved by using a Scaler Timer type 6255 and Sample Changer Control Interface type 6263. The interface used, however, has quite complex circuitry. The application therefore lends itself to the use of another 6000 Series module-the Integrated Counting System (ICS). Using this unit control is carried out through a control program written in BASIC for the Commodore PET (or any other device with an IEEE-488 interface). The ICS then controls the sample changer through an interface unit which is relatively simple. A brief description of how ICS controls the sample changer is given. The control program is then described; first the running options are given, followed by a program description listing and flowchart.

  5. A Cloud Top Pressure Algorithm for DSCOVR-EPIC

    Science.gov (United States)

    Min, Q.; Morgan, E. C.; Yang, Y.; Marshak, A.; Davis, A. B.

    2017-12-01

    The Earth Polychromatic Imaging Camera (EPIC) sensor on the Deep Space Climate Observatory (DSCOVR) satellite presents unique opportunities to derive cloud properties of the entire daytime Earth. In particular, the Oxygen A- and B-band and corresponding reference channels provide cloud top pressure information. In order to address the in-cloud penetration depth issue—and ensuing retrieval bias—a comprehensive sensitivity study has been conducted to simulate satellite-observed radiances for a wide variety of cloud structures and optical properties. Based on this sensitivity study, a cloud top pressure algorithm for DSCOVR-EPIC has been developed. Further, the algorithm has been applied to EPIC measurements.

  6. EPIC229426032 b and EPIC246067459 b: discovery and characterization of two new transiting hot Jupiters from K2

    Science.gov (United States)

    Soto, M. G.; Díaz, M. R.; Jenkins, J. S.; Rojas, F.; Espinoza, N.; Brahm, R.; Drass, H.; Jones, M. I.; Rabus, M.; Hartman, J.; Sarkis, P.; Jordán, A.; Lachaume, R.; Pantoja, B.; Vučković, M.; Ciardi, D. R.; Crossfield, I.; Dressing, C.; Gonzales, E.; Hirsch, L.

    2018-05-01

    We report the discovery of two hot Jupiters orbiting the stars EPIC229426032 and EPIC246067459. We used photometric data from Campaign 11 and 12 of the Kepler K2 Mission and radial velocity data obtained using the HARPS, FEROS, and CORALIE spectrographs. EPIC229426032 b and EPIC246067459 b have masses of 1.60^{+0.11}_{-0.11} and 0.86^{+0.13}_{-0.12}Mjup, radii of 1.65^{+0.07}_{-0.08} and 1.30^{+0.15}_{-0.14} R_{jup}, and are orbiting their host stars in 2.18 and 3.20-day orbits, respectively. The large radius of EPIC229426032 b leads us to conclude that this candidate corresponds to a highly inflated hot Jupiter. EPIC2460674559 b has a radius consistent with theoretical models, considering the high incident flux falling on the planet. We consider EPIC229426032 b to be a excellent system for follow-up studies, since not only is it very inflated, but it also orbits a relatively bright star (V = 11.6).

  7. Quality Control Samples for the Radiological Determination of Tritium in Urine Samples

    International Nuclear Information System (INIS)

    Ost'pezuk, P.; Froning, M.; Laumen, S.; Richert, I.; Hill, P.

    2004-01-01

    The radioactive decay product of tritium is a low energy beta that cannot penetrate the outer dead layer of human skin. Therefore , the main hazard associated with tritium is internal exposure. In addition, due to the relatively long half life and short biological half life, tritium must be ingested in large amounts to pose a significant health risk. On the other hand, the internal exposure should be kept as low as practical. For incorporation monitoring of professional radiation workers the quality control is of utmost importance. In the Research Centre Juelich GmbH (FZJ) a considerable fraction of monitoring by excretion analysis relates to the isotope Tritium. Usually an aliquot of an urine sample is mixed with a liquid scintillator and measured in a liquid scintillation counter. Quality control samples in the form of three kind of internal reference samples (blank, reference samples with low activity and reference sample with elevated activity) were prepared from a mixed, Tritium (free) urine samples. 1 ml of these samples were pipetted into a liquid scintillation vial. In the part of theses vials a known amounts of Tritium were added. All these samples were stored at 20 degrees. Based on long term use of all these reference samples it was possible to construct appropriate control charts with the upper and lower alarm limits. Daily use of these reference samples decrease significantly the risk for false results in original urine with no significant increase of the determination time. (Author) 2 refs

  8. Mapping Romanzo Criminale. An Epic Narrative Ecosystem?

    Directory of Open Access Journals (Sweden)

    Marta Boni

    2015-05-01

    Full Text Available Romanzo Criminale is one of the few recent Italian media products that has emerged as a societal phenomenon and as a vehicle for the exportation of a national culture. It is a complex narrative which extends in time and space due to its various adaptations and intermedial crossovers. Following the path of complexity, drawing on Edgar Morin’s work, Romanzo Criminale will be thought of as a complex system. As precedent studies on the intertwining of official and grassroots discourses show, Romanzo Criminale becomes a complex world, with its boundaries and internal organization. This paper will show that Romanzo Criminale can be studied as a semiosphere (Lotman 2005, or a semiotic space defined by and which encourages the intertwining of texts and audience appropriations, creating an epic process. Some methodological perspectives used for mapping this phenomenon will be discussed, namely Franco Moretti’s distant reading.

  9. The rebirth of the epic from the Nietzsche's Philosophy

    Directory of Open Access Journals (Sweden)

    Reza Samim

    2016-12-01

    Full Text Available his philosophy with Iranian mysticism. Such identification is fundamentally flawed and contradicts Nietzsche's ontological principles and moral values. Some of the Iranian commentators, expert in Nietzsche's philosophy, identified Nietzsche's thought is pregnant from the epic universal values, not the mystical patterns. Understanding of Nietzsche's Philosophy is possible with the help of Shahnameh and Iliad not mysticism. The reason of this fundamental error lies in the fact that these Iranian commentators fail to distinguish the subtle differences between mysticism and epic, and this failure, has led to their mixing Nietzsche's thought with the Iranian mysticism. Epic and mysticism are related in the differences not the similarities. Although there could be some similarities between the mystical worldview and that of epic, they are merely outward and superficial. In effect, in the matter of epistemic, moral and ontological principles, epic contradicts mysticism. At the best, mysticism can be considered to be the negative correspondence of epic and called “Negative Epic”. Nietzsche's thought has been affected to a greater extent by the Greek culture than and prior to the Iranian traditions. Nietzche's symbolic recourse to Zoroaster cannot be a cogent basis for these commentators' claim. Moreover, Nietzche's grasp of Zoroastrian worldview is so much blurred and incomplete. He appreciates the Greek culture not the Iranian traditions. Therefore, autonomy, voluntarism, appreciation of life and denunciation of passivity are the set of values and principles associating Nietzsche's philosophy with epic. These are exactly the principles disregarded and even denied in mystical thought. In other words, Nietzsche's philosophy can be considered the rebirth of the epic in the sphere of philosophical thought.

  10. Butterflies and Dragon-Eagles: Processing Epics from Southwest China

    Directory of Open Access Journals (Sweden)

    Mark Bender

    2012-03-01

    Full Text Available In the mountains of southwest China, epic narratives are part of the traditional performance-scapes of many ethnic minority cultures. In some cases locals participate in the preservation of oral or oral-connected epics from their respective areas. This article discusses the dynamics of acquiring and translating texts from two major ethnic minority groups in cooperation with local tradition-bearers, poets, and scholars.

  11. Sample size calculations for case-control studies

    Science.gov (United States)

    This R package can be used to calculate the required samples size for unconditional multivariate analyses of unmatched case-control studies. The sample sizes are for a scalar exposure effect, such as binary, ordinal or continuous exposures. The sample sizes can also be computed for scalar interaction effects. The analyses account for the effects of potential confounder variables that are also included in the multivariate logistic model.

  12. An instrumentation for control and measurement of activated mineral samples

    International Nuclear Information System (INIS)

    Skaarup, P.

    1976-01-01

    A description is given of an instrumentation for control of a pneumatic tube system used to transport mineral samples for activation in a reactor and from there to a detector arrangement. A possible content of uranium in the samples can be seen from the radiation measured. The instrumentation includes a PDP-11 computer and a CAMAC crate

  13. NEW EPICS/RTEMS IOC BASED ON ALTERA SOC AT JEFFERSON LAB

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Jianxun [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Seaton, Chad [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Allison, Trent L. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Bevins, Brian S. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Cuffe, Anthony W. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2018-02-01

    A new EPICS/RTEMS IOC based on the Altera System-on-Chip (SoC) FPGA is being designed at Jefferson Lab. The Altera SoC FPGA integrates a dual ARM Cortex-A9 Hard Processor System (HPS) consisting of processor, peripherals and memory interfaces tied seamlessly with the FPGA fabric using a high-bandwidth interconnect backbone. The embedded Altera SoC IOC has features of remote network boot via U-Boot from SD card or QSPI Flash, 1Gig Ethernet, 1GB DDR3 SDRAM on HPS, UART serial ports, and ISA bus interface. RTEMS for the ARM processor BSP were built with CEXP shell, which will dynamically load the EPICS applications at runtime. U-Boot is the primary bootloader to remotely load the kernel image into local memory from a DHCP/TFTP server over Ethernet, and automatically run RTEMS and EPICS. The first design of the SoC IOC will be compatible with Jefferson Lab’s current PC104 IOCs, which have been running in CEBAF 10 years. The next design would be mounting in a chassis and connected to a daughter card via standard HSMC connectors. This standard SoC IOC will become the next generation of low-level IOC for the accelerator controls at Jefferson Lab.

  14. Fault tolerant controllers for sampled-data systems

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik; Stoustrup, Jakob

    2004-01-01

    A general compensator architecture for fault tolerant control (FTC) for sampled-data systems is proposed. The architecture is based on the YJBK parameterization of all stabilizing controllers, and uses the dual YJBK parameterization to quantify the performance of the fault tolerant system. The FTC...

  15. An 'intelligent' approach to radioimmunoassay sample counting employing a microprocessor-controlled sample counter

    International Nuclear Information System (INIS)

    Ekins, R.P.; Sufi, S.; Malan, P.G.

    1978-01-01

    The enormous impact on medical science in the last two decades of microanalytical techniques employing radioisotopic labels has, in turn, generated a large demand for automatic radioisotopic sample counters. Such instruments frequently comprise the most important item of capital equipment required in the use of radioimmunoassay and related techniques and often form a principle bottleneck in the flow of samples through a busy laboratory. It is therefore imperative that such instruments should be used 'intelligently' and in an optimal fashion to avoid both the very large capital expenditure involved in the unnecessary proliferation of instruments and the time delays arising from their sub-optimal use. Most of the current generation of radioactive sample counters nevertheless rely on primitive control mechanisms based on a simplistic statistical theory of radioactive sample counting which preclude their efficient and rational use. The fundamental principle upon which this approach is based is that it is useless to continue counting a radioactive sample for a time longer than that required to yield a significant increase in precision of the measurement. Thus, since substantial experimental errors occur during sample preparation, these errors should be assessed and must be related to the counting errors for that sample. The objective of the paper is to demonstrate that the combination of a realistic statistical assessment of radioactive sample measurement, together with the more sophisticated control mechanisms that modern microprocessor technology make possible, may often enable savings in counter usage of the order of 5- to 10-fold to be made. (author)

  16. 'Intelligent' approach to radioimmunoassay sample counting employing a microprocessor controlled sample counter

    International Nuclear Information System (INIS)

    Ekins, R.P.; Sufi, S.; Malan, P.G.

    1977-01-01

    The enormous impact on medical science in the last two decades of microanalytical techniques employing radioisotopic labels has, in turn, generated a large demand for automatic radioisotopic sample counters. Such instruments frequently comprise the most important item of capital equipment required in the use of radioimmunoassay and related techniques and often form a principle bottleneck in the flow of samples through a busy laboratory. It is therefore particularly imperitive that such instruments should be used 'intelligently' and in an optimal fashion to avoid both the very large capital expenditure involved in the unnecessary proliferation of instruments and the time delays arising from their sub-optimal use. The majority of the current generation of radioactive sample counters nevertheless rely on primitive control mechanisms based on a simplistic statistical theory of radioactive sample counting which preclude their efficient and rational use. The fundamental principle upon which this approach is based is that it is useless to continue counting a radioactive sample for a time longer than that required to yield a significant increase in precision of the measurement. Thus, since substantial experimental errors occur during sample preparation, these errors should be assessed and must be releted to the counting errors for that sample. It is the objective of this presentation to demonstrate that the combination of a realistic statistical assessment of radioactive sample measurement, together with the more sophisticated control mechanisms that modern microprocessor technology make possible, may often enable savings in counter usage of the order of 5-10 fold to be made. (orig.) [de

  17. On the Issue of Origin of the Yakut Epic Olonkho

    Directory of Open Access Journals (Sweden)

    Vasiliy Nikolayevich Ivanov

    2018-03-01

    Full Text Available The issue on the origin of the Yakut heroic epic Olonkho was covered in works in history and ethnography of the Yakuts back in the 19th century, for instance, in the famous monograph Yakuts. Experience of ethnographic research by a Polish exile V.L. Seroshevskiy (1896. Since that time, this issue was interesting for many, but no special monograph research has been done yet. Currently, the issue of Olonkho origin is gaining special scientific and general cultural significance, as on November 25, 2005 the Yakut heroic epic Olonkho according to the historical decision of UNESCO was granted the high status “Masterpiece of oral and non-material heritage of humanity”. The Yakut epic is a part of the multicomponent epic creative work of the Turkic nations but it was the only one to get such a high international recognition. This paper aims to revive the scientific interest to the issue of the Yakut epic’s genesis. To date, some rich source-related and historiographical material has been accumulated for broader generalizations – the main point is that the Yakut epic is becoming an important object of comparative historical analysis of the origin of all Turkic epics. The thing is that epic researchers admit that almost a thousand years of existence isolated from the whole Turkic world in the North-East of Asia kept many archaic features of the epics of the ancient ancestors – natives of Central Asia and Southern Siberia. It became clear that Olonkho origin is organically linked with the ethnic history of its nation.The paper follows this comprehensive process reflected in works by archeologists, ethnographers, historians and linguists. Their latest achievements are impressive, bringing a lot of novelty into the conventional views of origins and development of the Yakut epic. The paper attempts to specify that novelty and rationalize the idea that time has come to introduce that novelty into science to solve the long-standing issue of origin of

  18. LabVIEW Library to EPICS Channel Access

    CERN Document Server

    Liyu, Andrei; Thompson, Dave H

    2005-01-01

    The Spallation Neutron Source (SNS) accelerator systems will deliver a 1.0 GeV, 1.4 MW proton beam to a liquid mercury target for neutron scattering research. The accelerator complex consists of a 1 GeV linear accelerator, an accumulator ring and associated transport lines. The SNS diagnostics platform is PC-based and will run Windows for its OS and LabVIEW as its programming language. Data acquisition hardware will be based on PCI cards. There will be about 300 rack-mounted computers. The Channel Access (CA) protocol of the Experimental Physics and Industrial Control System (EPICS) is the SNS control system communication standard. This paper describes the approaches, implementation, and features of LabVIEW library to CA for Windows, Linux, and Mac OS X. We also discuss how the library implements the asynchronous CA monitor routine using LabVIEW's occurrence mechanism instead of a callback function (which is not available in LabVIEW). The library is used to acquire accelerator data and applications have been ...

  19. Field-based random sampling without a sampling frame: control selection for a case-control study in rural Africa.

    Science.gov (United States)

    Crampin, A C; Mwinuka, V; Malema, S S; Glynn, J R; Fine, P E

    2001-01-01

    Selection bias, particularly of controls, is common in case-control studies and may materially affect the results. Methods of control selection should be tailored both for the risk factors and disease under investigation and for the population being studied. We present here a control selection method devised for a case-control study of tuberculosis in rural Africa (Karonga, northern Malawi) that selects an age/sex frequency-matched random sample of the population, with a geographical distribution in proportion to the population density. We also present an audit of the selection process, and discuss the potential of this method in other settings.

  20. Predictors of social anxiety in an opioid dependent sample and a control sample

    OpenAIRE

    Shand, Fiona L.; Degenhardt, Louisa; Nelson, Elliot C.; Mattick, Richard P.

    2010-01-01

    Compared to other mental health problems, social anxiety is under-acknowledged amongst opioid dependent populations. This study aimed to assess levels of social anxiety and identify its predictors in an opioid dependent sample and a matched control group. Opioid dependent participants (n = 1385) and controls (n = 417) completed the Social Interaction Anxiety Scale (SIAS), the Social Phobia Scale (SPS) and a diagnostic interview. Regression analyses were used to test a range of predictors of s...

  1. Research of pneumatic control transmission system for small irradiation samples

    International Nuclear Information System (INIS)

    Bai Zhongxiong; Zhang Haibing; Rong Ru; Zhang Tao

    2008-01-01

    In order to reduce the absorbed dose damage for the operator, pneumatic control has been adopted to realize the rapid transmission of small irradiation samples. On/off of pneumatic circuit and directions for the rapid transmission system are controlled by the electrical control part. The main program initializes the system and detects the location of the manual/automatic change-over switch, and call for the corresponding subprogram to achieve the automatic or manual operation. Automatic subprogram achieves the automatic sample transmission; Manual subprogram completes the deflation, and back and forth movement of the radiation samples. This paper introduces in detail the implementation of the system, in terms of both hardware and software design. (authors)

  2. Sampling and Control Circuit Board for an Inertial Measurement Unit

    Science.gov (United States)

    Chelmins, David T (Inventor); Powis, Richard T., Jr. (Inventor); Sands, Obed (Inventor)

    2016-01-01

    A circuit board that serves as a control and sampling interface to an inertial measurement unit ("IMU") is provided. The circuit board is also configured to interface with a local oscillator and an external trigger pulse. The circuit board is further configured to receive the external trigger pulse from an external source that time aligns the local oscillator and initiates sampling of the inertial measurement device for data at precise time intervals based on pulses from the local oscillator. The sampled data may be synchronized by the circuit board with other sensors of a navigation system via the trigger pulse.

  3. EPIC'S NEW REMOTE SENSING DATA AND INFORMATION TOOLS AVAILABLE FOR EPA CUSTOMERS

    Science.gov (United States)

    EPIC's New Remote Sensing Data and Information Tools Available for EPA Customers Donald Garofalo Environmental Photographic Interpretation Center (EPIC) Landscape Ecology Branch Environmental Sciences Division National Exposure Research Laboratory Several new too...

  4. The Cosmopolitan Epics of 2004: A Case Study

    Directory of Open Access Journals (Sweden)

    Assoc. Prof. Saverio Giovacchini

    2011-01-01

    Full Text Available In 2004 Hollywood produced three purportedly blockbuster epic films:Troy, King Arthur and Alexander. Many critics suggested a direct linkbetween the 1950s “sword and sandal” epic and this new crop of movies.Similarities between the two cycles certainly exist but in this essay I want to emphasize a crucial difference between the contemporary,cosmopolitan, epic and the previous, more nation-bound, 1950s cycle.Rather than being in tune with key elements of American foreign policy, the new cycle of “sword and sandal” films offers a somber assessment of American imperial adventures. I shall contend, in fact, that the new crop of epic films had to choose between two generic conventions that are, at present, not compatible. On the one hand, epic films had traditionally been the bearers of the foreign policy vision of the country that produced them. On the other, their inflated budgets made them dependent on an international market. Deeply aware of a globalized and rising opposition to US foreign policy and of the fact that foreign box office now exceeds the domestic take of a blockbuster, it may be no wonder that the makers of these films chose to craft them into citizens of the world.

  5. Chronicle and the epic: Machado de Assis in homeric verses

    Directory of Open Access Journals (Sweden)

    Ionara Satin

    2015-12-01

    Full Text Available The aim of this study is to show the presence of classical epic, Homer's Iliad, in the chronicle of Machado de Assis, analyzing the intertextual dialogue between Machado de Assis and the epic poem by Homer, considering the concept of intertextuality developed by Julia Kristeva from philosophical conceptions of Bakhtin. In the chronicle of March 18, 1894 for the newspaper Gazeta de Notícias on sunday column "A Semana", Machado de Assis crosses Homer's epic to his chronicle, rewrites the epic text for the daily issues of his weekly column. To Tiphaine Samoyault, writing is rewriting, "stand on the existing foundations and contribute to a continued creation" (2008, p. 77 one of the principles of intertextuality. It was observed that from the reading and assimilation of the classic poem, Machado de Assis can approach so far genres, bringing the verses to his prose, leaving it closer to poetry. In this sense, we can see the richness of Machado de Assis chronicles, often left on the sidelines in favor of his short stories and romances. In addition, the dialogue, to rewrite the epic in his chronicle, Machado seems to contribute to this "continuous creation", reviving the memory of literature and emphasizing the permanence of classical work.

  6. Rock sampling. [method for controlling particle size distribution

    Science.gov (United States)

    Blum, P. (Inventor)

    1971-01-01

    A method for sampling rock and other brittle materials and for controlling resultant particle sizes is described. The method involves cutting grooves in the rock surface to provide a grouping of parallel ridges and subsequently machining the ridges to provide a powder specimen. The machining step may comprise milling, drilling, lathe cutting or the like; but a planing step is advantageous. Control of the particle size distribution is effected primarily by changing the height and width of these ridges. This control exceeds that obtainable by conventional grinding.

  7. Characterization of rock samples and mineralogical controls on leachates

    Science.gov (United States)

    Hammarstrom, Jane M.; Cravotta, Charles A.; Galeone, Daniel G.; Jackson, John C.; Dulong, Frank T.; Hornberger, Roger J.; Brady, Keith B.C.

    2009-01-01

    Rocks associated with coal beds typically include shale, sandstone, and (or) limestone. In addition to common rock-forming minerals, all of these rock types may contain sulfide and sulfate minerals, various carbonate minerals, and organic material. These different minerals have inherently different solubility characteristics, as well as different acid-generating or acid-neutralizing potentials. The abundance and composition of sulfur- and carbonate-bearing minerals are of particular interest in interpreting the leaching column data because (1) pyrite and carbonate minerals are the primary controls on the acid-base account of a sample, (2) these minerals incorporate trace metals that can be released during weathering, and (3) these minerals readily react during weathering due to mineral dissolution and oxidation of iron.Rock samples were collected by the Pennsylvania Department of Environmental Protection (PaDEP) from five different sites to assess the draft standardized leaching column method (ADTI-WP2) for the prediction of weathering rates and water quality at coal mines. Samples were sent to USGS laboratories for mineralogical characterization and to ActLabs for chemical analysis. The samples represent a variety of rock types (shales, sandstones, and coal refuse) that are typical of coal overburden in the eastern United States. These particular samples were chosen for testing the weathering protocols because they represent a range of geochemical and lithologic characteristics, sulfur contents, and acid-base accounting characteristics (Hornberger et al., 2003). The rocks contain variable amounts of pyrite and carbonate minerals and vary in texture.This chapter includes bulk rock chemical data and detailed mineralogical and textural data for unweathered starting materials used in the interlaboratory validation study, and for two samples used in the early phases of leaching column tests (Wadesville Sandstone, Leechburg Coal Refuse). We also characterize some of the

  8. Sample Size Calculation for Controlling False Discovery Proportion

    Directory of Open Access Journals (Sweden)

    Shulian Shang

    2012-01-01

    Full Text Available The false discovery proportion (FDP, the proportion of incorrect rejections among all rejections, is a direct measure of abundance of false positive findings in multiple testing. Many methods have been proposed to control FDP, but they are too conservative to be useful for power analysis. Study designs for controlling the mean of FDP, which is false discovery rate, have been commonly used. However, there has been little attempt to design study with direct FDP control to achieve certain level of efficiency. We provide a sample size calculation method using the variance formula of the FDP under weak-dependence assumptions to achieve the desired overall power. The relationship between design parameters and sample size is explored. The adequacy of the procedure is assessed by simulation. We illustrate the method using estimated correlations from a prostate cancer dataset.

  9. Control System Radioactive Contamination in Food Samples in Poland

    International Nuclear Information System (INIS)

    Grabowski, D.; Kurowski, W.; Muszynski, W.; Rubel, B.; Smagala, G.; Swietochowska, J.

    2001-01-01

    Full text: The analyses of the level of radioactive contamination in food samples are carried out by the Service for Measurements of Radioactive Contamination (SMRC) in Poland. The Service was brought into existence in 1961. The Service comprises of a network of measurement stations and the Centre of Radioactive Contamination Measurements (CRCM). The duty of the Centre is being executed by the Central Laboratory for Radiological Protection (CLRP). The uniform methods of sampling are used in measurement stations. All important foodstuff: milk, meat, vegetables, fruit, cereals are controlled in the Service stations. The radiochemical and spectrometric methods are used to determine the activity of radioactive isotopes. The standard equipment of the measurement station is the measurement system type SAPOS-90 and multichannel analyser with scintillation or germanium detector. The structure of the Service, kinds of samples tested by each station, program of sampling in normal and during accident situation are presented in this paper. (author)

  10. Predictors of social anxiety in an opioid dependent sample and a control sample.

    Science.gov (United States)

    Shand, Fiona L; Degenhardt, Louisa; Nelson, Elliot C; Mattick, Richard P

    2010-01-01

    Compared to other mental health problems, social anxiety is under-acknowledged amongst opioid dependent populations. This study aimed to assess levels of social anxiety and identify its predictors in an opioid dependent sample and a matched control group. Opioid dependent participants (n=1385) and controls (n=417) completed the Social Interaction Anxiety Scale (SIAS), the Social Phobia Scale (SPS) and a diagnostic interview. Regression analyses were used to test a range of predictors of social anxiety. Opioid dependent cases had higher mean scores on both scales compared to controls. Predictors of social anxiety centred on emotional rejection in childhood, either by parents or peers. For opioid dependent cases, but not controls, lifetime non-opioid substance dependence (cannabis, sedatives, and tobacco) was associated with higher levels of social anxiety. However, much of the variance in social anxiety remains unexplained for this population.

  11. Pirate Alterity and Mimesis in Colonial Epic Poetry

    Directory of Open Access Journals (Sweden)

    Javier de Navascués

    2016-05-01

    Full Text Available Pirate representation is studied in a series of Epic poems in the late sixteenth century and early seventeenth century. The ambiguous image of the English enemy is read in texts by Juan de Miramontes, Pedro de Oña, Martín del Barco Centenera and Juan de Castellanos, among others. On the one hand, Colonial Epic ignores some important differences between privateers and pirates since the privateering had been legally accepted by all European nations, including Spain. Besides, Pirate is always called «Lutheran» and revealing its absolute otherness with respect to the Catholic model. On the other hand, it proposes a laudatory epics enemy painting from the imitation of the values accepted by the colonial society. The relationship between the Spanish hero and the privateer is represented not in a vertical direction, as could happen between colonizer and colonized subject, but on a level of rivalry.

  12. Collection and control of tritium bioassay samples at Pantex

    International Nuclear Information System (INIS)

    Fairrow, N.L.; Ivie, W.E.

    1992-01-01

    Pantex is the final assembly/disassembly point for US nuclear weapons. The Pantex internal dosimetry section monitors radiation workers once a month for tritium exposure. In order to manage collection and control of the bioassay specimens efficiently, a bar code system for collection of samples was developed and implemented to speed up the process and decrease the number of errors probable when transferring data. In the past, all the bioassay data from samples were entered manually into a computer database. Transferring the bioassay data from the liquid scintillation counter to each individual's dosimetry record required as much as two weeks of concentrated effort

  13. Helicobacter pylori infection assessed by ELISA and by immunoblot and noncardia gastric cancer risk in a prospective study: the Eurgast-EPIC project

    DEFF Research Database (Denmark)

    González, C A; Megraud, F; Buissoniere, A

    2012-01-01

    of its effect on gastric cancer (GC) risk. Antibodies detected by western blot are known to persist longer after the loss of the infection. In a nested case-control study from the Eurogast-EPIC cohort, including 88 noncardia GC cases and 338 controls, we assessed the association between noncardia GC...

  14. On Collecting and Publishing the Albanian Oral Epic

    Directory of Open Access Journals (Sweden)

    Arbnora Dushi

    2014-05-01

    Full Text Available The aim of this paper is to examine how the Albanian epic known as the ‘Cycle of the Frontier Warriors’ has been presented in Albanian folklore collections. I will examine seven written versions of the song ‘The Wedding of Ali Bajraktari’, which belongs to this epic cycle. The ‘Cycle of the Frontier Warriors’, has been an object of collection since the beginning of the twentieth century. There are now dozens of volumes published, but the studies published to date concentrate on historical, thematic and comparative rather than contextual and textual issues.

  15. Controls to validate plasma samples for cell free DNA quantification

    DEFF Research Database (Denmark)

    Pallisgaard, Niels; Spindler, Karen-Lise Garm; Andersen, Rikke Fredslund

    2015-01-01

    , are diverging due to methodological differences with lack of standardisation and definition of sensitivity. The new biological information has not yet come into routine use. The present study presents external standardisation by spiking with non-human DNA fragments to control for loss of DNA during sample...... preparation and measurement. It also suggests a method to control for admixture of DNA from normal lymphocytes by utilizing the unique immunoglobulin gene rearrangement in the B-cells. The results show that this approach improves the quality of the analysis and lowers the risk of falsely increased values...

  16. Implementation of KoHLT-EB DAQ System using compact RIO with EPICS

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Dae-Sik; Kim, Suk-Kwon; Lee, Dong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Cho, Seungyon [National Fusion Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    EPICS (Experimental Physics and Industrial Control System) is a collection of software tools collaboratively developed which can be integrated to provide a comprehensive and scalable control system. Currently there is an increase in use of such systems in large Physics experiments like KSTAR, ITER and DAIC (Daejeon Accelerator Ion Complex). The Korean heat load test facility (KoHLT-EB) was installed at KAERI. This facility is utilized for a qualification test of the plasma facing component (PFC) for the ITER first wall and DEMO divertor, and the thermo-hydraulic experiments. The existing data acquisition device was Agilent 34980A multifunction switch and measurement unit and controlled by Agilent VEE. In the present paper, we report the EPICS based newly upgraded KoHLT-EB DAQ system which is the advanced data acquisition system using FPGA-based reconfigurable DAQ devices like compact RIO. The operator interface of KoHLT-EB DAQ system is composed of Control-System Studio (CSS) and another server is able to archive the related data using the standalone archive tool and the archiveviewer can retrieve that data at any time in the infra-network.

  17. Molecular genetic analysis of cereal β-amylase genes using exon-primed intron-crossing (EPIC PCR

    Directory of Open Access Journals (Sweden)

    Stratula Olga

    2014-01-01

    Full Text Available The proteins encoded by cereal β-amylase genes Bamy1 and Bamy2 genes play an important role in seedling germination and in the brewing process. Here, we use exon-primed intron-crossing (EPIC to analyse Bamy1 and Bamy2 genetic diversity among 38 accessions belonging to six Poaceae tribes. DNA sequence alignment of multiple Poaceae species β-amylase sequences allowed design of EPIC primers that simultaneously amplify Bamy1 and Bamy2 in all the cereal species investigated. The genetic variation observed in the samples investigated is analysed and discussed, and illustrates the effectiveness of this approach for intra- and interspecific analysis in plant species.

  18. Extrasolar Planetary Imaging Coronagraph (EPIC): visible nulling cornagraph testbed results

    Science.gov (United States)

    Lyon, Richard G.; Clampin, Mark; Melnick, Gary; Tolls, Volker; Woodruff, Robert; Vasudevan, Gopal

    2008-07-01

    The Extrasolar Planetary Imaging Coronagraph (EPIC) is a NASA Astrophysics Strategic Mission Concept under study for the upcoming Exoplanet Probe. EPIC's mission would be to image and characterize extrasolar giant planets, and potential super-Earths, in orbits with semi-major axes between 2 and 10 AU. EPIC will provide insights into the physical nature of a variety of planets in other solar systems complimenting radial velocity (RV) and astrometric planet searches. It will detect and characterize the atmospheres of planets identified by radial velocity surveys and potentially some transits, determine orbital inclinations and masses, characterize the atmospheres of gas giants around A and F stars, observed the inner spatial structure and colors of inner Spitzer selected debris disks. EPIC would be launched into a heliocentric Earth trailing drift-away orbit, with a 3-year mission lifetime (5 year goal) and will revisit planets at least three times. The starlight suppression approach consists of a visible nulling coronagraph (VNC) that enables high order starlight suppression in broadband light. To demonstrate the VNC approach and advance it's technology readiness the NASA/Goddard Space Flight Center and Lockheed-Martin have developed a laboratory VNC and have demonstrated white light nulling. We will discuss our ongoing VNC work and show the latest results from the VNC testbed.

  19. Anthropometry and the risk of lung cancer in EPIC

    NARCIS (Netherlands)

    Dewi, Nikmah Utami; Boshuizen, Hendriek C.; Johansson, Mattias; Vineis, Paolo; Kampman, Ellen; Steffen, Annika; Tjønneland, Anne; Halkjær, Jytte; Overvad, Kim; Severi, Gianluca; Fagherazzi, Guy; Boutron-Ruault, Marie Christine; Kaaks, Rudolf; Li, Kuanrong; Boeing, Heiner; Trichopoulou, Antonia; Bamia, Christina; Klinaki, Eleni; Tumino, Rosario; Palli, Domenico; Mattiello, Amalia; Tagliabue, Giovanna; Peeters, Petra H.; Vermeulen, Roel; Weiderpass, Elisabete; Gram, Inger Torhild; Huerta, José María; Agudo, Antonio; Sánchez, María José; Ardanaz, Eva; Dorronsoro, Miren; Quirós, José Ramón; Sonestedt, Emily; Johansson, Mikael; Grankvist, Kjell; Key, Tim; Khaw, Kay Tee; Wareham, Nick; Cross, Amanda J.; Norat, Teresa; Riboli, Elio; Fanidi, Anouar; Muller, David; Bueno-De-Mesquita, H.B.

    2016-01-01

    The associations of body mass index (BMI) and other anthropometric measurements with lung cancer were examined in 348,108 participants in the European Investigation Into Cancer and Nutrition (EPIC) between 1992 and 2010. The study population included 2,400 case patients with incident lung cancer,

  20. Anthropometry and the Risk of Lung Cancer in EPIC

    NARCIS (Netherlands)

    Dewi, Nikmah Utami; Boshuizen, Hendriek C; Johansson, Mattias; Vineis, Paolo; Kampman, Ellen; Steffen, Annika; Tjønneland, Anne; Halkjær, Jytte; Overvad, Kim; Severi, Gianluca; Fagherazzi, Guy; Boutron-Ruault, Marie-Christine; Kaaks, Rudolf; Li, Kuanrong; Boeing, Heiner; Trichopoulou, Antonia; Bamia, Christina; Klinaki, Eleni; Tumino, Rosario; Palli, Domenico; Mattiello, Amalia; Tagliabue, Giovanna; Peeters, Petra H; Vermeulen, Roel; Weiderpass, Elisabete; Torhild Gram, Inger; Huerta, José María; Agudo, Antonio; Sánchez, María-José; Ardanaz, Eva; Dorronsoro, Miren; Quirós, José Ramón; Sonestedt, Emily; Johansson, Mikael; Grankvist, Kjell; Key, Tim; Khaw, Kay-Tee; Wareham, Nick; Cross, Amanda J; Norat, Teresa; Riboli, Elio; Fanidi, Anouar; Muller, David; Bueno-de-Mesquita, H Bas

    2016-01-01

    The associations of body mass index (BMI) and other anthropometric measurements with lung cancer were examined in 348,108 participants in the European Investigation Into Cancer and Nutrition (EPIC) between 1992 and 2010. The study population included 2,400 case patients with incident lung cancer,

  1. Anthropometry and the risk of lung cancer in EPIC

    NARCIS (Netherlands)

    Dewi, Nikmah Utami; Boshuizen, Hendriek C.; Johansson, Mattias; Vineis, Paolo; Kampman, Ellen; Steffen, Annika; Tjønneland, Anne; Halkjær, Jytte; Overvad, Kim; Severi, Gianluca; Fagherazzi, Guy; Boutron-Ruault, Marie Christine; Kaaks, Rudolf; Li, Kuanrong; Boeing, Heiner; Trichopoulou, Antonia; Bamia, Christina; Klinaki, Eleni; Tumino, Rosario; Palli, Domenico; Mattiello, Amalia; Tagliabue, Giovanna; Peeters, Petra H.; Vermeulen, Roel; Weiderpass, Elisabete; Gram, Inger Torhild; Huerta, José María; Agudo, Antonio; Sánchez, María José; Ardanaz, Eva; Dorronsoro, Miren; Quirós, José Ramón; Sonestedt, Emily; Johansson, Mikael; Grankvist, Kjell; Key, Tim; Khaw, Kay Tee; Wareham, Nick; Cross, Amanda J.; Norat, Teresa; Riboli, Elio; Fanidi, Anouar; Muller, David; Bueno-De-Mesquita, H. Bas

    2016-01-01

    The associations of body mass index (BMI) and other anthropometric measurements with lung cancer were examined in 348,108 participants in the European Investigation Into Cancer and Nutrition (EPIC) between 1992 and 2010. The study population included 2,400 case patients with incident lung cancer,

  2. Eating out, weight and weight gain. A cross-sectional and prospective analysis in the context of the EPIC-PANACEA study.

    Science.gov (United States)

    Naska, A; Orfanos, P; Trichopoulou, A; May, A M; Overvad, K; Jakobsen, M U; Tjønneland, A; Halkjær, J; Fagherazzi, G; Clavel-Chapelon, F; Boutron-Ruault, M-C; Rohrmann, S; Hermann, S; Steffen, A; Haubrock, J; Oikonomou, E; Dilis, V; Katsoulis, M; Sacerdote, C; Sieri, S; Masala, G; Tumino, R; Mattiello, A; Bueno-de-Mesquita, H B; Skeie, G; Engeset, D; Barricarte, A; Rodríguez, L; Dorronsoro, M; Sánchez, M-J; Chirlaque, M-D; Agudo, A; Manjer, J; Wirfält, E; Hellström, V; Shungin, D; Khaw, K-T; Wareham, N J; Spencer, E A; Freisling, H; Slimani, N; Vergnaud, A-C; Mouw, T; Romaguera, D; Odysseos, A; Peeters, P H M

    2011-03-01

    The aim of this study was to examine the association of body mass index (BMI) and weight gain with eating at restaurants and similar establishments or eating at work among 10 European countries of the European Prospective Investigation into Cancer and Nutrition (EPIC) study. This study included a representative sample of 24,310 randomly selected EPIC participants. Single 24-h dietary recalls with information on the place of consumption were collected using standardized procedures between 1995 and 2000. Eating at restaurants was defined to include all eating and drinking occasions at restaurants, cafeterias, bars and fast food outlets. Eating at work included all eating and drinking occasions at the workplace. Associations between eating at restaurants or eating at work and BMI or annual weight changes were assessed using sex-specific linear mixed-effects models, controlling for potential confounders. In southern Europe energy intake at restaurants was higher than intake at work, whereas in northern Europe eating at work appeared to contribute more to the mean daily intake than eating at restaurants. Cross-sectionally, eating at restaurants was found to be positively associated with BMI only among men (β=+0.24, P=0.003). Essentially no association was found between BMI and eating at work among both genders. In a prospective analysis among men, eating at restaurants was found to be positively, albeit nonsignificantly, associated with weight gain (β=+0.05, P=0.368). No association was detected between energy intake at restaurants and weight changes, controlling for total energy intake. Among men, eating at restaurants and similar establishments was associated with higher BMI and possibly weight gain.

  3. Preview-based sampling for controlling gaseous simulations

    KAUST Repository

    Huang, Ruoguan

    2011-01-01

    In this work, we describe an automated method for directing the control of a high resolution gaseous fluid simulation based on the results of a lower resolution preview simulation. Small variations in accuracy between low and high resolution grids can lead to divergent simulations, which is problematic for those wanting to achieve a desired behavior. Our goal is to provide a simple method for ensuring that the high resolution simulation matches key properties from the lower resolution simulation. We first let a user specify a fast, coarse simulation that will be used for guidance. Our automated method samples the data to be matched at various positions and scales in the simulation, or allows the user to identify key portions of the simulation to maintain. During the high resolution simulation, a matching process ensures that the properties sampled from the low resolution simulation are maintained. This matching process keeps the different resolution simulations aligned even for complex systems, and can ensure consistency of not only the velocity field, but also advected scalar values. Because the final simulation is naturally similar to the preview simulation, only minor controlling adjustments are needed, allowing a simpler control method than that used in prior keyframing approaches. Copyright © 2011 by the Association for Computing Machinery, Inc.

  4. Computer-controlled sampling system for airborne particulates

    International Nuclear Information System (INIS)

    Hall, C.F.; Anspaugh, L.R.; Koval, J.S.; Phelps, P.L.; Steinhaus, R.J.

    1975-01-01

    A self-contained, mobile, computer-controlled air-sampling system has been designed and fabricated that also collects and records the data from eight meteorological sensors. The air-samplers are activated automatically when the collected meteorological data meet the criteria specified at the beginning of the data-collection run. The filters from the samplers are intended to collect airborne 239 Pu for later radionuclide analysis and correlation with the meteorological data for the study of resuspended airborne radioactivity and for the development of a predictive model. This paper describes the system hardware, discusses the system and software concepts, and outlines the operational procedures for the system

  5. CAFE, a modern C++ interface to the EPICS channel access library

    International Nuclear Information System (INIS)

    Chrin, J.; Sloan, M.C.

    2012-01-01

    CAFE (Channel Access interface) is a C++ library that provides a modern, multifaceted interface to the EPICS-based control system that we may find in particle accelerators for instance. CAFE makes extensive use of templates and containers with multiple STL-compatible access methods to enhance efficiency, flexibility and performance. Stability and robustness are accomplished by ensuring that connectivity to EPICS channels remains in a well defined state in every eventuality, and results of all synchronous and asynchronous operations are captured and reported with integrity. CAFE presents the user with a number of options for writing and retrieving data to and from the control system. In addition to basic read and write operations, a further abstraction layer provides transparency to more intricate functionalities involving logical sets of data; such 'group' objects are easily instantiated through an XML-based configuration mechanism. CAFE's suitability for use in a broad spectrum of applications is demonstrated. These range from high performance Qt GUI (Graphical User Interface) control widgets, to event processing agents that propagate data through the Object Managements Group's Data Distribution Service (OMG-DDS), to script-like frameworks such as MATLAB. The methodology for the modular use of CAFE serves to improve maintainability by enforcing a logical boundary between the channel access components and the programming extensions of the application framework at hand. (authors)

  6. Costs and financing of routine immunization: Approach and selected findings of a multi-country study (EPIC).

    Science.gov (United States)

    Brenzel, Logan; Young, Darwin; Walker, Damian G

    2015-05-07

    Few detailed facility-based costing studies of routine immunization (RI) programs have been conducted in recent years, with planners, managers and donors relying on older information or data from planning tools. To fill gaps and improve quality of information, a multi-country study on costing and financing of routine immunization and new vaccines (EPIC) was conducted in Benin, Ghana, Honduras, Moldova, Uganda and Zambia. This paper provides the rationale for the launch of the EPIC study, as well as outlines methods used in a Common Approach on facility sampling, data collection, cost and financial flow estimation for both the routine program and new vaccine introduction. Costing relied on an ingredients-based approach from a government perspective. Estimating incremental economic costs of new vaccine introduction in contexts with excess capacity are highlighted. The use of more disaggregated System of Health Accounts (SHA) coding to evaluate financial flows is presented. The EPIC studies resulted in a sample of 319 primary health care facilities, with 65% of facilities in rural areas. The EPIC studies found wide variation in total and unit costs within each country, as well as between countries. Costs increased with level of scale and socio-economic status of the country. Governments are financing an increasing share of total RI financing. This study provides a wealth of high quality information on total and unit costs and financing for RI, and demonstrates the value of in-depth facility approaches. The paper discusses the lessons learned from using a standardized approach, as well as proposes further areas of methodology development. The paper discusses how results can be used for resource mobilization and allocation, improved efficiency of services at the country level, and to inform policies at the global level. Efforts at routinizing cost analysis to support sustainability efforts would be beneficial. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Adiponectin and risk of coronary heart disease in apparently healthy men and women (from the EPIC-Norfolk Prospective Population Study)

    NARCIS (Netherlands)

    Côté, Mélanie; Cartier, Amélie; Reuwer, Anne Q.; Arsenault, Benoit J.; Lemieux, Isabelle; Després, Jean-Pierre; Wareham, Nicholas J.; Kastelein, John J. P.; Boekholdt, S. Matthijs; Khaw, Kay-Tee

    2011-01-01

    The objective of the present study was to evaluate the association between adiponectin levels and incidence of coronary heart disease (CHD). We performed a prospective case-control analysis nested in the EPIC-Norfolk cohort. Participants were apparently healthy men and women 45 to 79 years of age

  8. Phytosterol plasma concentrations and coronary heart disease in the prospective Spanish EPIC cohort

    Science.gov (United States)

    Escurriol, Verónica; Cofán, Montserrat; Moreno-Iribas, Concepción; Larrañaga, Nerea; Martínez, Carmen; Navarro, Carmen; Rodríguez, Laudina; González, Carlos A.; Corella, Dolores; Ros, Emilio

    2010-01-01

    Phytosterol intake with natural foods, a measure of healthy dietary choices, increases plasma levels, but increased plasma phytosterols are believed to be a coronary heart disease (CHD) risk factor. To address this paradox, we evaluated baseline risk factors, phytosterol intake, and plasma noncholesterol sterol levels in participants of a case control study nested within the European Prospective Investigation into Cancer and Nutrition (EPIC) Spanish cohort who developed CHD (n = 299) and matched controls (n = 584) who remained free of CHD after a 10 year follow-up. Sitosterol-to-cholesterol ratios increased across tertiles of phytosterol intake (P = 0.026). HDL-cholesterol level increased, and adiposity measures, cholesterol/HDL ratios, and levels of glucose, triglycerides, and lathosterol, a cholesterol synthesis marker, decreased across plasma sitosterol tertiles (P phytosterol intake and plasma sitosterol. The multivariable-adjusted odds ratio for CHD across the lowest to highest plasma sitosterol tertile was 0.59 (95% confidence interval, 0.36–0.97). Associations were weaker for plasma campesterol. The apolipoprotein E genotype was unrelated to CHD risk or plasma phytosterols. The data suggest that plasma sitosterol levels are associated with a lower CHD risk while being markers of a lower cardiometabolic risk in the EPIC-Spain cohort, a population with a high phytosterol intake. PMID:19786566

  9. Cooking of meat and fish in Europe--results from the European Prospective Investigation into Cancer and Nutrition (EPIC).

    Science.gov (United States)

    Rohrmann, S; Linseisen, J; Becker, N; Norat, T; Sinha, R; Skeie, G; Lund, E; Martínez, C; Barricarte, A; Mattisson, I; Berglund, G; Welch, A; Davey, G; Overvad, K; Tjønneland, A; Clavel-Chapelon, F; Kesse, E; Lotze, G; Klipstein-Grobusch, K; Vasilopoulou, E; Polychronopoulos, E; Pala, V; Celentano, E; Bueno-De-Mesquita, H B; Peeters, P H M; Riboli, E; Slimani, N

    2002-12-01

    There is epidemiologic evidence that the consumption of fried, grilled or barbecued meat and fish that are well-done or browned may be associated with an increased cancer risk. These high-temperature cooking methods are thought to be surrogates for mutagens and carcinogens produced in meat and fish, eg heterocyclic amines or polycyclic hydrocarbons. Since data on food cooking methods are scarce, the aim of this study was to describe the variation in meat and fish cooking methods in different parts of Europe. Using a standardized 24 h recall from a sub-sample of the EPIC cohort (35 644 persons, 35-75 y old), mean daily intake of meat and fish prepared by different cooking methods and the relative contribution of the cooking methods to the overall cooking of meat and fish was calculated. Whereas frying was more often noted in northern Europe, roasting and stir frying were more often used in the south. Concerning high-temperature cooking methods, their frequency of application varies between 15% in the EPIC cohort of North-Italy and 49% in the cohort of The Netherlands. Average consumption of fried, grilled and barbecued meat and fish ranges from a low of 12 g/day in the centres in southern Spain to a high of 91 g/day in northern Spain. High variation in both the kind of meat/fish consumed as well as its cooking methods is observed within EPIC. In order to use this variation for the evaluation of the impact of cooking methods on cancer risk, a questionnaire on meat and fish cooking methods is being developed and could be applied in the whole EPIC cohort.

  10. Context-specific attentional sampling: Intentional control as a pre-requisite for contextual control.

    Science.gov (United States)

    Brosowsky, Nicholaus P; Crump, Matthew J C

    2016-08-01

    Recent work suggests that environmental cues associated with previous attentional control settings can rapidly and involuntarily adjust attentional priorities. The current study tests predictions from adaptive-learning and memory-based theories of contextual control about the role of intentions for setting attentional priorities. To extend the empirical boundaries of contextual control phenomena, and to determine whether theoretical principles of contextual control are generalizable we used a novel bi-dimensional stimulus sampling task. Subjects viewed briefly presented arrays of letters and colors presented above or below fixation, and identified specific stimuli according to a dimensional (letter or color) and positional cue. Location was predictive of the cued dimension, but not the position or identity. In contrast to previous findings, contextual control failed to develop through automatic, adaptive-learning processes. Instead, previous experience with intentionally changing attentional sampling priorities between different contexts was required for contextual control to develop. Copyright © 2016 Elsevier Inc. All rights reserved.

  11. Quantum Ensemble Classification: A Sampling-Based Learning Control Approach.

    Science.gov (United States)

    Chen, Chunlin; Dong, Daoyi; Qi, Bo; Petersen, Ian R; Rabitz, Herschel

    2017-06-01

    Quantum ensemble classification (QEC) has significant applications in discrimination of atoms (or molecules), separation of isotopes, and quantum information extraction. However, quantum mechanics forbids deterministic discrimination among nonorthogonal states. The classification of inhomogeneous quantum ensembles is very challenging, since there exist variations in the parameters characterizing the members within different classes. In this paper, we recast QEC as a supervised quantum learning problem. A systematic classification methodology is presented by using a sampling-based learning control (SLC) approach for quantum discrimination. The classification task is accomplished via simultaneously steering members belonging to different classes to their corresponding target states (e.g., mutually orthogonal states). First, a new discrimination method is proposed for two similar quantum systems. Then, an SLC method is presented for QEC. Numerical results demonstrate the effectiveness of the proposed approach for the binary classification of two-level quantum ensembles and the multiclass classification of multilevel quantum ensembles.

  12. Connect high speed analog-digital converter with EPICS based on LabVIEW

    International Nuclear Information System (INIS)

    Wang Wei; Chi Yunlong

    2008-01-01

    This paper introduce a method to connect high speed analog-digital converter (ADC212/100) with EPICS on Windows platform using LabVIEW. We use labVIEW to communicate with the converter, then use interface sub-VIs between LabVIEW and EPICS to access the EPICS IOC by Channel Access (CA). For the easy use graph programming language of LabVIEW, this method could shorten the develop period and reduce manpower cost. (authors)

  13. A Consistent EPIC Visible Channel Calibration Using VIIRS and MODIS as a Reference.

    Science.gov (United States)

    Haney, C.; Doelling, D. R.; Minnis, P.; Bhatt, R.; Scarino, B. R.; Gopalan, A.

    2017-12-01

    The Earth Polychromatic Imaging Camera (EPIC) aboard the Deep Space Climate Observatory (DSCOVR) satellite constantly images the sunlit disk of Earth from the Lagrange-1 (L1) point in 10 spectral channels spanning the UV, VIS, and NIR spectrums. Recently, the DSCOVR EPIC team has publicly released version 2 dataset, which has implemented improved navigation, stray-light correction, and flat-fielding of the CCD array. The EPIC 2-year data record must be well-calibrated for consistent cloud, aerosol, trace gas, land use and other retrievals. Because EPIC lacks onboard calibrators, the observations made by EPIC channels must be calibrated vicariously using the coincident measurements from radiometrically stable instruments that have onboard calibration systems. MODIS and VIIRS are best-suited instruments for this task as they contain similar spectral bands that are well-calibrated onboard using solar diffusers and lunar tracking. We have previously calibrated the EPIC version 1 dataset by using EPIC and VIIRS angularly matched radiance pairs over both all-sky ocean and deep convective clouds (DCC). We noted that the EPIC image required navigations adjustments, and that the EPIC stray-light correction provided an offset term closer to zero based on the linear regression of the EPIC and VIIRS ray-matched radiance pairs. We will evaluate the EPIC version 2 navigation and stray-light improvements using the same techniques. In addition, we will monitor the EPIC channel calibration over the two years for any temporal degradation or anomalous behavior. These two calibration methods will be further validated using desert and DCC invariant Earth targets. The radiometric characterization of the selected invariant targets is performed using multiple years of MODIS and VIIRS measurements. Results of these studies will be shown at the conference.

  14. [Is the socioeconomic deprivation EPICES score useful in obstetrics?].

    Science.gov (United States)

    Convers, M; Langeron, A; Sass, C; Moulin, J-J; Augier, A; Varlet, M-N; Seffert, P; Chêne, G

    2012-04-01

    To describe a validated and multifactorial deprivation score to study the relationship between socioeconomic deprivation and perinatal risks. The index of deprivation EPICES (Evaluation of Precarity and Inequalities in Health Examination Centers) was used to characterize the deprivation status of 234 women in post-partum in comparison with perinatal morbidity. The cutoff value of 30.7 was the threshold to define deprivation. Two hundred and eight patients were included in this retrospective study from whom 48 (23%) had a score of deprivation higher than 30.7. Maternofetal morbidity was more severe in deprived patients. The current results show that the EPICES score could be a useful obstetrical tool for the identification of deprived women during pregnancy. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

  15. Implementation of an EPICS IOC on an Embedded Soft Core Processor Using Field Programmable Gate Arrays

    International Nuclear Information System (INIS)

    Douglas Curry; Alicia Hofler; Hai Dong; Trent Allison; J. Hovater; Kelly Mahoney

    2005-01-01

    At Jefferson Lab, we have been evaluating soft core processors running an EPICS IOC over μClinux on our custom hardware. A soft core processor is a flexible CPU architecture that is configured in the FPGA as opposed to a hard core processor which is fixed in silicon. Combined with an on-board Ethernet port, the technology incorporates the IOC and digital control hardware within a single FPGA. By eliminating the general purpose computer IOC, the designer is no longer tied to a specific platform, e.g. PC, VME, or VXI, to serve as the intermediary between the high level controls and the field hardware. This paper will discuss the design and development process as well as specific applications for JLab's next generation low-level RF controls and Machine Protection Systems

  16. Cooperative vehicle control, feature tracking and ocean sampling

    Science.gov (United States)

    Fiorelli, Edward A.

    This dissertation concerns the development of a feedback control framework for coordinating multiple, sensor-equipped, autonomous vehicles into mobile sensing arrays to perform adaptive sampling of observed fields. The use of feedback is central; it maintains the array, i.e. regulates formation position, orientation, and shape, and directs the array to perform its sampling mission in response to measurements taken by each vehicle. Specifically, we address how to perform autonomous gradient tracking and feature detection in an unknown field such as temperature or salinity in the ocean. Artificial potentials and virtual bodies are used to coordinate the autonomous vehicles, modelled as point masses (with unit mass). The virtual bodies consist of linked, moving reference points called virtual leaders. Artificial potentials couple the dynamics of the vehicles and the virtual bodies. The dynamics of the virtual body are then prescribed allowing the virtual body, and thus the vehicle group, to perform maneuvers that include translation, rotation and contraction/expansion, while ensuring that the formation error remains bounded. This methodology is called the Virtual Body and Artificial Potential (VBAP) methodology. We then propose how to utilize these arrays to perform autonomous gradient climbing and front tracking in the presence of both correlated and uncorrelated noise. We implement various techniques for estimation of gradients (first-order and higher), including finite differencing, least squares error minimization, averaging, and Kalman filtering. Furthermore, we illustrate how the estimation error can be used to optimally choose the formation size. To complement our theoretical work, we present an account of sea trials performed with a fleet of autonomous underwater gliders in Monterey Bay during the Autonomous Ocean Sampling Network (AOSN) II project in August 2003. During these trials, Slocum autonomous underwater gliders were coordinated into triangle

  17. Epic and Romance in The Lord Of The Rings

    Directory of Open Access Journals (Sweden)

    Martin Simonson

    2016-10-01

    Full Text Available In the field of comparative literature The Lord of the Rings has been most frequently studied within the contexts of romance and epic. This approach, however, leaves out important generic aspects of the global picture, such as the narrative’s strong adherence to the novel genre and to mythic traditions beyond romance and epic narratives. If we choose one particular genre as the yardstick against which to measure the work’s success in narrative terms, we tend to end up with the conclusion that The Lord of the Rings does not quite make sense within the given limits of the genre in question. In Tolkien’s work there is a narrative and stylistic exploration of the different genres’ constraints in which the Western narrative traditions – myth, epic, romance, the novel, and their respective subgenres – interact in a previously unknown but still very much coherent world that, because of the particular cohesion required by such a chronotope, exhibits a clear contextualization of references to the previous traditions. As opposed to many contemporary literary expressions, the ensuing absence of irony and parody creates a generic dialogue, in which the various narrative traditions explore and interrogate each other’s limits without rendering the others absurdly incompatible, ridiculous or superfluous.

  18. Optimal grade control sampling practice in open-pit mining

    DEFF Research Database (Denmark)

    Engström, Karin; Esbensen, Kim Harry

    2017-01-01

    Misclassification of ore grades results in lost revenues, and the need for representative sampling procedures in open pit mining is increasingly important in all mining industries. This study evaluated possible improvements in sampling representativity with the use of Reverse Circulation (RC) drill...... sampling compared to manual Blast Hole (BH) sampling in the Leveäniemi open pit mine, northern Sweden. The variographic experiment results showed that sampling variability was lower for RC than for BH sampling. However, the total costs for RC drill sampling are significantly exceeding current costs...... for manual BH sampling, which needs to be compensated for by other benefits to motivate introduction of RC drilling. The main conclusion is that manual BH sampling can be fit-for-purpose in the studied open pit mine. However, with so many mineral commodities and mining methods in use globally...

  19. Virtual IO controllers at J-PARC MR using Xen

    International Nuclear Information System (INIS)

    Kamikubota, N.; Yamada, S.; Yamamoto, N.; Iitsuka, T.; Motohashi, S.; Takagi, M.; Yoshida, S.; Nemoto, H.

    2012-01-01

    The control system for J-PARC accelerator complex has been developed based on the EPICS tool-kit. About 90 traditional ('real') VME-bus computers are used as EPICS IOCs (Input/Output Controller) in the control system for J-PARC MR (Main Ring). In 2010-2011, we demonstrated a 'virtual' IOC using Xen, an open-source virtual machine monitor. Scientific Linux with an EPICS IOC runs on a Xen virtual machine. EPICS records for oscilloscopes (network devices) are configured. Advantages of virtual IOC are discussed. In addition, future directions are discussed. Plan view of virtual IOCs for MR operation will be given. (authors)

  20. Enhancement of real-time EPICS IOC PV management for the data archiving system

    Science.gov (United States)

    Kim, Jae-Ha

    2015-10-01

    The operation of a 100-MeV linear proton accelerator, the major driving values and experimental data need to be archived. According to the experimental conditions, different data are required. Functions that can add new data and delete data in real time need to be implemented. In an experimental physics and industrial control system (EPICS) input output controller (IOC), the value of process variables (PVs) are matched with the driving values and data. The PV values are archived in text file format by using the channel archiver. There is no need to create a database (DB) server, just a need for large hard disk. Through the web, the archived data can be loaded, and new PV values can be archived without stopping the archive engine. The details of the implementation of a data archiving system with channel archiver are presented, and some preliminary results are reported.

  1. The K2 Ecliptic Plane Input Catalog (EPIC) and Stellar Classifications of 138,600 Targets in Campaigns 1-8

    Science.gov (United States)

    Huber, Daniel; Bryson, Stephen T.; Haas, Michael R.; Barclay, Thomas; Barentsen, Geert; Howell, Steve B.; Sharma, Sanjib; Stello, Dennis; Thompson, Susan E.

    2016-05-01

    The K2 Mission uses the Kepler spacecraft to obtain high-precision photometry over ≈80 day campaigns in the ecliptic plane. The Ecliptic Plane Input Catalog (EPIC) provides coordinates, photometry, and kinematics based on a federation of all-sky catalogs to support target selection and target management for the K2 mission. We describe the construction of the EPIC, as well as modifications and shortcomings of the catalog. Kepler magnitudes (Kp) are shown to be accurate to ≈0.1 mag for the Kepler field, and the EPIC is typically complete to Kp ≈ 17 (Kp ≈ 19 for campaigns covered by Sloan Digital Sky Survey). We furthermore classify 138,600 targets in Campaigns 1-8 (≈88% of the full target sample) using colors, proper motions, spectroscopy, parallaxes, and galactic population synthesis models, with typical uncertainties for G-type stars of ≈3% in {T}{{eff}}, ≈0.3 dex in {log} g, ≈40% in radius, ≈10% in mass, and ≈40% in distance. Our results show that stars targeted by K2 are dominated by K-M dwarfs (≈41% of all selected targets), F-G dwarfs (≈36%), and K giants (≈21%), consistent with key K2 science programs to search for transiting exoplanets and galactic archeology studies using oscillating red giants. However, we find significant variation of the fraction of cool dwarfs with galactic latitude, indicating a target selection bias due to interstellar reddening and increased contamination by giant stars near the galactic plane. We discuss possible systematic errors in the derived stellar properties, and differences with published classifications for K2 exoplanet host stars. The EPIC is hosted at the Mikulski Archive for Space Telescopes (MAST): http://archive.stsci.edu/k2/epic/search.php.

  2. Chimpanzee responding during matching to sample: control by exclusion.

    OpenAIRE

    Beran, Michael J; Washburn, David A

    2002-01-01

    Three chimpanzees performed a computerized matching-to-sample task in which samples were photographs of items and comparison stimuli were geometric symbols called lexigrams. In Experiment 1, samples were either defined (i.e., they represented items that were associated already with a specific lexigram label by the chimpanzees) or undefined (i.e., they did not have an already learned association with a specific lexigram). On each trial, the foil (incorrect) comparison could be either a defined...

  3. Controlled chloride cracking of austenitic stainless steel tube samples

    OpenAIRE

    Raseroka, M.S.; Pistorius, P.C.

    2009-01-01

    An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperatur...

  4. A versatile trigger and synchronization module with IEEE1588 capabilities and EPICS support

    International Nuclear Information System (INIS)

    Lopez, J.M.; Ruiz, M.; Borrego, J.; Arcas, G. de; Barrera, E.; Vega, J.

    2010-01-01

    Event timing and synchronization are two key aspects to improve in the implementation of distributed data acquisition (dDAQ) systems such as the ones used in fusion experiments. It is also of great importance the integration of dDAQ in control and measurement networks. This paper analyzes the applicability of the IEEE1588 and EPICS standards to solve these problems, and presents a hardware module implementation based in both of them that allow adding these functionalities to any DAQ. The IEEE1588 standard facilitates the integration of event timing and synchronization mechanisms in distributed data acquisition systems based on IEEE 803.3 (Ethernet). An optimal implementation of such system requires the use of network interface devices which include specific hardware resources devoted to the IEE1588 functionalities. Unfortunately, this is not the approach followed in most of the large number of applications available nowadays. Therefore, most solutions are based in software and use standard hardware network interfaces. This paper presents the development of a hardware module (GI2E) with IEEE1588 capabilities which includes USB, RS232, RS485 and CAN interfaces. This permits to integrate any DAQ element that uses these interfaces in dDAQ systems in an efficient and simple way. The module has been developed with Motorola's Coldfire MCF5234 processor and National Semiconductors's PHY DP83640T, providing it with the possibility to implement the PTP protocol of IEEE1588 by hardware, and therefore increasing its performance over other implementations based in software. To facilitate the integration of the dDAQ system in control and measurement networks the module includes a basic Input/Output Controller (IOC) functionality of the Experimental Physics and Industrial Control System (EPICS) architecture. The paper discusses the implementation details of this module and presents its applications in advanced dDAQ applications in the fusion community.

  5. Sampling

    CERN Document Server

    Thompson, Steven K

    2012-01-01

    Praise for the Second Edition "This book has never had a competitor. It is the only book that takes a broad approach to sampling . . . any good personal statistics library should include a copy of this book." —Technometrics "Well-written . . . an excellent book on an important subject. Highly recommended." —Choice "An ideal reference for scientific researchers and other professionals who use sampling." —Zentralblatt Math Features new developments in the field combined with all aspects of obtaining, interpreting, and using sample data Sampling provides an up-to-date treat

  6. Patterns of alcohol consumption in 10 European countries participating in the EPIC project

    DEFF Research Database (Denmark)

    Sieri, S.; Agudo, A.; Kesse, E.

    2002-01-01

    , are characterised by widely differing drinking habits and frequencies of alcohol-related diseases. Methods: We collected a single standardised 24-hour dietary recall per subject from a random sample of the EPIC cohort (36 900 persons initially and 35 955 after exclusion of subjects under 35 and over 74 years of age......). This provided detailed information on the distribution of alcohol consumption during the day in relation to main meals, and was used to determine weekly consumption patterns. The crude and adjusted (by age, day of week and season) means of total ethanol consumption and consumption according to type of beverage...... were stratified by centre and sex. Results: Sex was a strong determinant of drinking patterns in all 10 countries. The highest total alcohol consumption was observed in the Spanish centres (San Sebastian, 41.4 g day−1) for men and in Danish centres (Copenhagen, 20.9 g day−1) for women. The lowest total...

  7. Turbidity-controlled sampling for suspended sediment load estimation

    Science.gov (United States)

    Jack Lewis

    2003-01-01

    Abstract - Automated data collection is essential to effectively measure suspended sediment loads in storm events, particularly in small basins. Continuous turbidity measurements can be used, along with discharge, in an automated system that makes real-time sampling decisions to facilitate sediment load estimation. The Turbidity Threshold Sampling method distributes...

  8. Adaptive control of theophylline therapy: importance of blood sampling times.

    Science.gov (United States)

    D'Argenio, D Z; Khakmahd, K

    1983-10-01

    A two-observation protocol for estimating theophylline clearance during a constant-rate intravenous infusion is used to examine the importance of blood sampling schedules with regard to the information content of resulting concentration data. Guided by a theory for calculating maximally informative sample times, population simulations are used to assess the effect of specific sampling times on the precision of resulting clearance estimates and subsequent predictions of theophylline plasma concentrations. The simulations incorporated noise terms for intersubject variability, dosing errors, sample collection errors, and assay error. Clearance was estimated using Chiou's method, least squares, and a Bayesian estimation procedure. The results of these simulations suggest that clinically significant estimation and prediction errors may result when using the above two-point protocol for estimating theophylline clearance if the time separating the two blood samples is less than one population mean elimination half-life.

  9. New development of EPICS based data acquisition system for H-Alpha diagnostic

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Taegu, E-mail: glory@nfri.re.kr; Lee, Woongryol; Son, Souhun; Park, Jinseop

    2015-10-15

    Highlights: • The H-Alpha DAQ system was modified to measure the low current signal from the PMT. • We developed a new H-Alpha data acquisition system with a CPCI based digitizer. • We developed a signal conditioning box for converting the current to voltage. • The new signal condition box (SCB) has three input range level (400 nA, 1 μA and 2 μA). • It was successfully performed and stably operates more than the previous DAQ system. - Abstract: The H-Alpha diagnostic system has been developed to measure the line integrated intensity in the direction of toroidal and poloidal. The data acquisition (DAQ) system for H-Alpha diagnostics of the Korea Superconducting Tokamak Advanced Research (KSTAR) at the beginning of the first plasma in 2008 was developed with VME form factor digitizer in the Linux OS platform. The VME digitizer module of H-Alpha data acquisition system was modified to measure the low current signal from the photo-multiplier tubes (PMT). The input maximum current values of modified digitizer module are 400 nA and low current data is expressed as the value of the voltage between −10 V and +10 V. At first time, there was no problem to measure H-Alpha signal, but it could not measure the H-Alpha data signal as the KSTAR Plasma density increased. It exceeds digitizer input range, which means the H-Alpha signal is over 400 nA, so we should manually change the resistor on the digitizer board to measure the 400 nA over current. This is not easy to do and showed instability in the long time operation with high sampling data acquisition. In order to overcome these weak points, a new H-Alpha data acquisition system has been developed with a compact PCI (cPCI) based digitizer and a signal conditioning box for converting the current to voltage in the Linux OS platform. The new data acquisition system was developed based on Experimental Physics and Industrial Control System (EPICS) framework like other KSTAR diagnostics with standard framework (SFW

  10. 78 FR 69363 - Lake Tahoe Basin Management Unit, California, Heavenly Mountain Resort Epic Discovery Project

    Science.gov (United States)

    2013-11-19

    ... DEPARTMENT OF AGRICULTURE Forest Service Lake Tahoe Basin Management Unit, California, Heavenly Mountain Resort Epic Discovery Project AGENCY: Lake Tahoe Basin Management Unit, Forest Service, USDA...: The Epic Discovery Project is intended to enhance summer activities in response to the USDA Forest...

  11. 75 FR 65985 - Safety Zone: Epic Roasthouse Private Party Firework Display, San Francisco, CA

    Science.gov (United States)

    2010-10-27

    ... the navigable waters of San Francisco Bay 1,000 yards off Epic Roasthouse Restaurant, San Francisco.... Wright, Program Manager, Docket Operations, telephone 202-366-9826. SUPPLEMENTARY INFORMATION: Regulatory... waters of San Francisco Bay, 1,000 yards off Epic Roasthouse Restaurant, San Francisco, CA. The fireworks...

  12. Chapter 5: Quality assurance/quality control in stormwater sampling

    Science.gov (United States)

    Sampling the quality of stormwater presents unique challenges because stormwater flow is relatively short-lived with drastic variability. Furthermore, storm events often occur with little advance warning, outside conventional work hours, and under adverse weather conditions. Therefore, most stormwat...

  13. Sample size optimization in nuclear material control. 1

    International Nuclear Information System (INIS)

    Gladitz, J.

    1982-01-01

    Equations have been derived and exemplified which allow the determination of the minimum variables sample size for given false alarm and detection probabilities of nuclear material losses and diversions, respectively. (author)

  14. Preview-based sampling for controlling gaseous simulations

    KAUST Repository

    Huang, Ruoguan; Melek, Zeki; Keyser, John

    2011-01-01

    to maintain. During the high resolution simulation, a matching process ensures that the properties sampled from the low resolution simulation are maintained. This matching process keeps the different resolution simulations aligned even for complex systems

  15. Plasma phospholipid fatty acid concentration and incident coronary heart disease in men and women: the EPIC-Norfolk prospective study.

    Directory of Open Access Journals (Sweden)

    Kay-Tee Khaw

    Full Text Available The lack of association found in several cohort studies between dietary saturated fat and coronary heart disease (CHD risk has renewed debate over the link between dietary fats and CHD.We assessed the relationship between plasma phospholipid fatty acid (PFA concentration and incident CHD using a nested case control design within a prospective study (EPIC-Norfolk of 25,639 individuals aged 40-79 years examined in 1993-1997 and followed up to 2009. Plasma PFA concentrations were measured by gas chromatography in baseline samples retrieved from frozen storage. In 2,424 men and women with incident CHD compared with 4,930 controls alive and free of cardiovascular disease, mean follow-up 13 years, saturated PFA (14:0, 16:0,18:0 plasma concentrations were significantly associated with increased CHD risk (odds ratio [OR] 1.75, 95% CI 1.27-2.41, p<0.0001, in top compared to bottom quartiles (Q, and omega-6 polyunsaturated PFA concentrations were inversely related (OR 0.77, 0.60-0.99, p<0.05 after adjusting for age, sex, body mass index, blood pressure, smoking, alcohol intake, plasma vitamin C, social class, education, and other PFAs. Monounsaturated PFA, omega-3 PFA, and trans PFA concentrations were not significantly associated with CHD. Odd chain PFA (15:0, 17:0 concentrations were significantly inversely associated with CHD (OR 0.73, 0.59-0.91, p<0.001, Q4 versus Q1. Within families of saturated PFA or polyunsaturated PFA, significantly heterogeneous relationships with CHD were observed for individual fatty acids.In this study, plasma concentrations of even chain saturated PFA were found to be positively and omega-6 polyunsaturated PFA inversely related to subsequent coronary heart disease risk. These findings are consistent with accumulating evidence suggesting a protective role of omega-6 fats substituting for saturated fats for CHD prevention.

  16. Comparison of Different Matrices as Potential Quality Control Samples for Neurochemical Dementia Diagnostics

    NARCIS (Netherlands)

    Lelental, Natalia; Brandner, Sebastian; Kofanova, Olga; Blennow, Kaj; Zetterberg, Henrik; Andreasson, Ulf; Engelborghs, Sebastiaan; Mroczko, Barbara; Gabryelewicz, Tomasz; Teunissen, Charlotte; Mollenhauer, Brit; Parnetti, Lucilla; Chiasserini, Davide; Molinuevo, Jose Luis; Perret-Liaudet, Armand; Verbeek, Marcel M.; Andreasen, Niels; Brosseron, Frederic; Bahl, Justyna M. C.; Herukka, Sanna-Kaisa; Hausner, Lucrezia; Froelich, Lutz; Labonte, Anne; Poirier, Judes; Miller, Anne-Marie; Zilka, Norbert; Kovacech, Branislav; Urbani, Andrea; Suardi, Silvia; Oliveira, Catarina; Baldeiras, Ines; Dubois, Bruno; Rot, Uros; Lehmann, Sylvain; Skinningsrud, Anders; Betsou, Fay; Wiltfang, Jens; Gkatzima, Olymbia; Winblad, Bengt; Buchfelder, Michael; Kornhuber, Johannes; Lewczuk, Piotr

    2016-01-01

    Background: Assay-vendor independent quality control (QC) samples for neurochemical dementia diagnostics (NDD) biomarkers are so far commercially unavailable. This requires that NDD laboratories prepare their own QC samples, for example by pooling leftover cerebrospinal fluid (CSF) samples.

  17. Juvencus and the biblical epic: specificity and literary criticism

    Directory of Open Access Journals (Sweden)

    Elena María Calderón de Cuervo

    2015-04-01

    Full Text Available Latin Christian poetry has emerged in  Constantine Era and flourished between 400 and 800. It has a fundamental role in the development of literary theory and critical discourse, because, except for Prudencio, the rest of the poets of this first period has chosen by the adaptation of the classical canon to Christian themes. The Christian epic is therefore one of the first genres and begins as biblical epic. The first major work of this type is the Gospel Harmony from the Spanish poet Juvencus, until 330. This work begins a long series of biblical poetry, Latin at first, but after this there is its continuation in the vernaculars, like Caedmon, Cynewulf, The Heliand, The Passion by Clermont till Ojeda, Milton and Klopstock.The dedication to the established authority , the subordination of the art´s purpose for the salvation of the soul as well as the desire to legitimize poetry with Christian arguments remain as fundamental premises in the construction of gender. When the modern epic apear, its compromise with new theological Aporia will not lose those extraliterary requirements from provenance.Keywords: Latin Christian poetry; Constantine Era; Virgil.

  18. Use of EPICS and Python technology for the development of a computational toolkit for high heat flux testing of plasma facing components

    Energy Technology Data Exchange (ETDEWEB)

    Sugandhi, Ritesh, E-mail: ritesh@ipr.res.in; Swamy, Rajamannar, E-mail: rajamannar@ipr.res.in; Khirwadkar, Samir, E-mail: sameer@ipr.res.in

    2016-11-15

    Highlights: • An integrated approach to software development for computational processing and experimental control. • Use of open source, cross platform, robust and advanced tools for computational code development. • Prediction of optimized process parameters for critical heat flux model. • Virtual experimentation for high heat flux testing of plasma facing components. - Abstract: The high heat flux testing and characterization of the divertor and first wall components are a challenging engineering problem of a tokamak. These components are subject to steady state and transient heat load of high magnitude. Therefore, the accurate prediction and control of the cooling parameters is crucial to prevent burnout. The prediction of the cooling parameters is based on the numerical solution of the critical heat flux (CHF) model. In a test facility for high heat flux testing of plasma facing components (PFC), the integration of computations and experimental control is an essential requirement. Experimental physics and industrial control system (EPICS) provides powerful tools for steering controls, data simulation, hardware interfacing and wider usability. Python provides an open source alternative for numerical computations and scripting. We have integrated these two open source technologies to develop a graphical software for a typical high heat flux experiment. The implementation uses EPICS based tools namely IOC (I/O controller) server, control system studio (CSS) and Python based tools namely Numpy, Scipy, Matplotlib and NOSE. EPICS and Python are integrated using PyEpics library. This toolkit is currently under operation at high heat flux test facility at Institute for Plasma Research (IPR) and is also useful for the experimental labs working in the similar research areas. The paper reports the software architectural design, implementation tools and rationale for their selection, test and validation.

  19. Use of EPICS and Python technology for the development of a computational toolkit for high heat flux testing of plasma facing components

    International Nuclear Information System (INIS)

    Sugandhi, Ritesh; Swamy, Rajamannar; Khirwadkar, Samir

    2016-01-01

    Highlights: • An integrated approach to software development for computational processing and experimental control. • Use of open source, cross platform, robust and advanced tools for computational code development. • Prediction of optimized process parameters for critical heat flux model. • Virtual experimentation for high heat flux testing of plasma facing components. - Abstract: The high heat flux testing and characterization of the divertor and first wall components are a challenging engineering problem of a tokamak. These components are subject to steady state and transient heat load of high magnitude. Therefore, the accurate prediction and control of the cooling parameters is crucial to prevent burnout. The prediction of the cooling parameters is based on the numerical solution of the critical heat flux (CHF) model. In a test facility for high heat flux testing of plasma facing components (PFC), the integration of computations and experimental control is an essential requirement. Experimental physics and industrial control system (EPICS) provides powerful tools for steering controls, data simulation, hardware interfacing and wider usability. Python provides an open source alternative for numerical computations and scripting. We have integrated these two open source technologies to develop a graphical software for a typical high heat flux experiment. The implementation uses EPICS based tools namely IOC (I/O controller) server, control system studio (CSS) and Python based tools namely Numpy, Scipy, Matplotlib and NOSE. EPICS and Python are integrated using PyEpics library. This toolkit is currently under operation at high heat flux test facility at Institute for Plasma Research (IPR) and is also useful for the experimental labs working in the similar research areas. The paper reports the software architectural design, implementation tools and rationale for their selection, test and validation.

  20. Exon-primed intron-crossing (EPIC markers for non-model teleost fishes

    Directory of Open Access Journals (Sweden)

    Riethoven Jean-Jack M

    2010-03-01

    Full Text Available Abstract Background Exon-primed intron-crossing (EPIC markers have three advantages over anonymous genomic sequences in studying evolution of natural populations. First, the universal primers designed in exon regions can be applied across a broad taxonomic range. Second, the homology of EPIC-amplified sequences can be easily determined by comparing either their exon or intron portion depending on the genetic distance between the taxa. Third, having both the exon and intron fragments could help in examining genetic variation at the intraspecific and interspecific level simultaneously, particularly helpful when studying species complex. However, the paucity of EPIC markers has hindered multilocus studies using nuclear gene sequences, particularly in teleost fishes. Results We introduce a bioinformatics pipeline for developing EPIC markers by comparing the whole genome sequences between two or more species. By applying this approach on five teleost fishes whose genomes were available in the Ensembl database http://www.ensembl.org, we identified 210 EPIC markers that have single-copy and conserved exon regions with identity greater than 85% among the five teleost fishes. We tested 12 randomly chosen EPIC markers in nine teleost species having a wide phylogenetic range. The success rate of amplifying and sequencing those markers varied from 44% to 100% in different species. We analyzed the exon sequences of the 12 EPIC markers from 13 teleosts. The resulting phylogeny contains many traditionally well-supported clades, indicating the usefulness of the exon portion of EPIC markers in reconstructing species phylogeny, in addition to the value of the intron portion of EPIC markers in interrogating the population history. Conclusions This study illustrated an effective approach to develop EPIC markers in a taxonomic group, where two or more genome sequences are available. The markers identified could be amplified across a broad taxonomic range of teleost

  1. Quality control for measurement of soil samples containing 237Np and 241Am as radiotracer

    International Nuclear Information System (INIS)

    Sha Lianmao; Zhang Caihong; Song Hailong; Ren Xiaona; Han Yuhu; Zhang Aiming; Chu Taiwei

    2003-01-01

    This paper reports quality control (QC) for the measurement of soil samples containing 237 Np and 241 Am as radiotracers in migration test of transuranic nuclides. All of the QC were done independently by the QA members of analytical work. It mainly included checking 5%-10% of the total analyzed samples; preparing blank samples, blind replicate sample and spiked samples used as quality control samples to check the quality of analytical work

  2. EPIC OF AWESOMEANIMÁTICA DE UN EPISODIO PILOTO

    OpenAIRE

    PEIRÓ TIMONER, LLORENÇ ANDREU

    2016-01-01

    [EN] Epic of Awesome is a pre-production project for an animated short in 2D, produced entirely using specialized software for story-board creation. The project includes every phase prior to the final animation stage needed for the production of audiovisual narratives: idea, research, script, designs, initial story-board, final story-board, layout, voice acting, music and effects, animatics, clean-up and the final edition of the animated short. The story, exposed in a comedic tone with the in...

  3. Poetry’s Politics in Archaic Greek Epic and Lyric

    Directory of Open Access Journals (Sweden)

    David F. Elmer

    2013-03-01

    Full Text Available This essay builds on work in The Poetics of Consent (2013, which argues that the Iliad’s representation of politics reflects the workings of the oral tradition underlying the poem as we have it, a tradition that developed in the context of Panhellenic festivals. Applying a similar perspective to poetry belonging to the very different performative context of the symposium, this essay draws evidence from Theognis and Alcaeus suggesting that the social dynamics of sympotic performance could be expressed in terms of political fragmentation and alienation. In the Odyssey, the contrast between the epic singers Phemios and Demodokos reflects an awareness of the difference between these performative contexts.

  4. Sampled-data and discrete-time H2 optimal control

    NARCIS (Netherlands)

    Trentelman, Harry L.; Stoorvogel, Anton A.

    1993-01-01

    This paper deals with the sampled-data H2 optimal control problem. Given a linear time-invariant continuous-time system, the problem of minimizing the H2 performance over all sampled-data controllers with a fixed sampling period can be reduced to a pure discrete-time H2 optimal control problem. This

  5. PC-based input/output controllers from a VME perspective

    International Nuclear Information System (INIS)

    Hill, J.O.

    1999-01-01

    The Experimental Physics and Industrial Control System (EPICS) has been widely adopted in the accelerator community. Although EPICS is available on many platforms, the majority of sites have deployed VME- or VXI-based input output controllers running the vxWorks real time operating system. Recently, a hybrid approach using vxWorks on both PC and traditional platforms is being implemented at LANL. To illustrate these developments the author compares his recent experience deploying PC-based EPICS input output controllers with experience deploying similar systems based on traditional EPICS platforms

  6. Apolipoprotein C-III Levels and Incident Coronary Artery Disease Risk: The EPIC-Norfolk Prospective Population Study.

    Science.gov (United States)

    van Capelleveen, Julian C; Bernelot Moens, Sophie J; Yang, Xiaohong; Kastelein, John J P; Wareham, Nicholas J; Zwinderman, Aeilko H; Stroes, Erik S G; Witztum, Joseph L; Hovingh, G Kees; Khaw, Kay-Tee; Boekholdt, S Matthijs; Tsimikas, Sotirios

    2017-06-01

    Apolipoprotein C-III (apoC-III) is a key regulator of triglyceride metabolism. Elevated triglyceride-rich lipoproteins and apoC-III levels are causally linked to coronary artery disease (CAD) risk. The mechanism(s) through which apoC-III increases CAD risk remains largely unknown. The aim was to confirm the association between apoC-III plasma levels and CAD risk and to explore which lipoprotein subfractions contribute to this relationship between apoC-III and CAD risk. Plasma apoC-III levels were measured in baseline samples from a nested case-control study in the European Prospective Investigation of Cancer (EPIC)-Norfolk study. The study comprised 2711 apparently healthy study participants, of whom 832 subsequently developed CAD. We studied the association of baseline apoC-III levels with incident CAD risk, lipoprotein subfractions measured by nuclear magnetic resonance spectroscopy and inflammatory biomarkers. ApoC-III levels were significantly associated with CAD risk (odds ratio, 1.91; 95% confidence interval, 1.48-2.48 for highest compared with lowest quintile), retaining significance after adjustment for traditional CAD risk factors (odds ratio, 1.47; 95% confidence interval, 1.11-1.94). ApoC-III levels were positively correlated with triglyceride levels, ( r =0.39), particle numbers of very-low-density lipoprotein ( r =0.25), intermediate-density lipoprotein ( r =0.23), small dense low-density lipoprotein ( r =0.26), and high-sensitivity C-reactive protein ( r =0.15), whereas an inverse correlation was observed with large low-density lipoprotein particle number ( r =-0.11), P C-reactive protein. ApoC-III levels are significantly associated with incident CAD risk. Elevated levels of remnant lipoproteins, small dense low-density lipoprotein, and low-grade inflammation may explain this association. © 2017 American Heart Association, Inc.

  7. Development and Validation of WebQuests in Teaching Epics

    Directory of Open Access Journals (Sweden)

    Ronald Candy Santos Lasaten

    2017-05-01

    Full Text Available Using the Research Development (R&D methodology, the study aimed to develop and validate WebQuests which can be used in literature subjects, particularly in the tertiary level to address the need of literature teachers for pedagogy in the teaching of epic s. The development of the Web Quests was anchored on the Theory of Constructivism. Two groups of experts validated the Web Quests – the literature experts and the ICT experts. The Content Validation Checklist, used by the literature experts, was utilized t o evaluate the content of the Web Quests. Meanwhile, the Rubric for Evaluating Web Quests, used by the ICT experts, was utilized to evaluate the design characteristics of the Web Quests. Computed weighted means using range interval of point scores were emp loyed to treat the data gathered from the evaluation conducted by both group of experts. The Web Quests developed contain five major parts which include: 1 introduction; 2 task; 3 process; 4 evaluation; and 5 conclusion. Based on the findings, the con tent of the Web Quests developed are valid in terms of objectives, activities and instructional characteristics. Likewise, the design characteristics of the Web Quests are excellent in terms of introductions, tasks, processes, resources, evaluations, concl usions and overall designs. Thus, the Web Quests developed are acceptable and can be utilized as instructional materials by literature teachers in the teaching of epics.

  8. Indigenous women in Spanish American Historic Epic Poetry

    Directory of Open Access Journals (Sweden)

    Lise Segas

    2016-05-01

    Full Text Available Epic poetry has always been considered a masculine genre. The eruption of a group identity, masculine, white, aristocratic and christian, is the result of the representation and the exclusion of the Other, fictitious and singular, but in fact composed of a variety of ethnic groups, origins, sex, genders, religions and different degrees between fiction and historicity. Indeed, in the historical epic poetry which narrated the Conquest, except for the conquistadors listed at length and the indigenous kings and caciques, only few characters are distinguished by a historical individualisation. The Other, Amerindian and female, makes a shy entrance into history, into singularity, into the (historical and christian truth. It is the case of interpreters: Malinche and India Catalina, only historical native women that appear as part of the narrative plot as well as in the conquest enterprise in the poems of Lasso de la Vega (Cortés valeroso y Mexicana, Mexicana, of Juan de Castellanos (Elegías de varones ilustres de Indias and of Saavedra Guzmán (El peregrino indiano.

  9. Optimal sampling period of the digital control system for the nuclear power plant steam generator water level control

    International Nuclear Information System (INIS)

    Hur, Woo Sung; Seong, Poong Hyun

    1995-01-01

    A great effort has been made to improve the nuclear plant control system by use of digital technologies and a long term schedule for the control system upgrade has been prepared with an aim to implementation in the next generation nuclear plants. In case of digital control system, it is important to decide the sampling period for analysis and design of the system, because the performance and the stability of a digital control system depend on the value of the sampling period of the digital control system. There is, however, currently no systematic method used universally for determining the sampling period of the digital control system. Generally, a traditional way to select the sampling frequency is to use 20 to 30 times the bandwidth of the analog control system which has the same system configuration and parameters as the digital one. In this paper, a new method to select the sampling period is suggested which takes into account of the performance as well as the stability of the digital control system. By use of the Irving's model steam generator, the optimal sampling period of an assumptive digital control system for steam generator level control is estimated and is actually verified in the digital control simulation system for Kori-2 nuclear power plant steam generator level control. Consequently, we conclude the optimal sampling period of the digital control system for Kori-2 nuclear power plant steam generator level control is 1 second for all power ranges. 7 figs., 3 tabs., 8 refs. (Author)

  10. Fruit and vegetable intake and type 2 diabetes: EPIC-InterAct prospective study and meta-analysis

    Science.gov (United States)

    Cooper, Andrew J; Forouhi, Nita G; Ye, Zheng; Buijsse, Brian; Arriola, Larraitz; Balkau, Beverley; Barricarte, Aurelio; Beulens, Joline WJ; Boeing, Heiner; Büchner, Frederike L; Dahm, Christina C; de Lauzon-Guillain, Blandine; Fagherazzi, Guy; Franks, Paul W; Gonzalez, Carlos; Grioni, Sara; Kaaks, Rudolf; Key, Timothy J; Masala, Giovanna; Navarro, Carmen; Nilsson, Peter; Overvad, Kim; Panico, Salvatore; Quirós, Jose Ramón; Rolandsson, Olov; Roswall, Nina; Sacerdote, Carlotta; Sánchez, María-José; Slimani, Nadia; Sluijs, Ivonne; Spijkerman, Annemieke MW; Teucher, Birgit; Tjonneland, Anne; Tumino, Rosario; Sharp, Stephen J; Langenberg, Claudia; Feskens, Edith JM; Riboli, Elio; Wareham, Nicholas J

    2013-01-01

    Background/Objective Fruit and vegetable intake (FVI) may reduce the risk of type 2 diabetes (T2D), but the epidemiological evidence is inconclusive. The aim of this study is to examine the prospective association of FVI with T2D and conduct an updated meta-analysis. Subjects/Methods In the EPIC-InterAct (European Prospective Investigation into Cancer-InterAct) prospective case-cohort study nested within eight European countries, a representative sample of 16 154 participants and 12 403 incident cases of T2D were identified from 340 234 individuals with 3.99 million person-years of follow-up. For the meta-analysis we identified prospective studies on FVI and T2D risk by systematic searches of MEDLINE and EMBASE until April 2011. Results In EPIC-InterAct, estimated FVI by dietary questionnaires varied more than two-fold between countries. In adjusted analyses the hazard ratio (95% confidence interval) comparing the highest with lowest quartile of reported intake was 0.90 (0.80-1.01) for FVI; 0.89 (0.76-1.04) for fruit, and 0.94 (0.84-1.05) for vegetables. Among FV sub-types, only root vegetables were inversely associated with diabetes 0.87 (0.77-0.99). In meta-analysis using pooled data from five studies including EPIC-InterAct, comparing the highest with lowest category for FVI was associated with a lower relative risk of diabetes (0.93 (0.87-1.00)). Fruit or vegetables separately were not associated with diabetes. Among FV sub-types, only green leafy vegetable intake (RR: 0.84 (0.74-0.94)) was inversely associated with diabetes. Conclusions Sub-types of vegetables, such as root vegetables or green leafy vegetables may be beneficial for the prevention of diabetes, while total FVI may exert a weaker overall effect. PMID:22854878

  11. Control of the hafnium content in Co samples by SSMS

    International Nuclear Information System (INIS)

    Lukaszew, R.A.; Cretella, R.F.

    1989-01-01

    The production of 60 Co requires a strict control of the chemical composition of the cobalt before irradiation in order to avoid the activation of some undesirable elements and to constrain the presence of slow neutron poisons. A methodology by SSMS for the survey analysis of metallic Co prior to its irradiation in the nuclear reactor at Embalse (Cdba., Argentina) is described. The low detection limit attained for Hf (below 0.5 ppm) is outlined. The results obtained for some other impurities without a standard reference are compared with atomic emission spectrographic data and show satisfactory agreement. (orig.)

  12. Sampled Data Adaptive Digital Computer Control of Surface Ship Maneuvers

    Science.gov (United States)

    1976-06-01

    0.53 feet. Systems fcr which fuel considerations are not a motivating 157 factor lay te designed without this part of the control law ta allow finer...COXXXQXxaQXQ«^2Q£>’^ o>- —,>->>>ozor X < a. Ps4 <i i— « aC _J o < a o-*»-» ujOO • •>- o • •oo«mo z o «j II II ** » < ii ii -^ -* -,-^a:- i—— * O.-IUJ

  13. Quality-control design for surface-water sampling in the National Water-Quality Network

    Science.gov (United States)

    Riskin, Melissa L.; Reutter, David C.; Martin, Jeffrey D.; Mueller, David K.

    2018-04-10

    The data-quality objectives for samples collected at surface-water sites in the National Water-Quality Network include estimating the extent to which contamination, matrix effects, and measurement variability affect interpretation of environmental conditions. Quality-control samples provide insight into how well the samples collected at surface-water sites represent the true environmental conditions. Quality-control samples used in this program include field blanks, replicates, and field matrix spikes. This report describes the design for collection of these quality-control samples and the data management needed to properly identify these samples in the U.S. Geological Survey’s national database.

  14. Status of the Experimental Physics and Industrial Control System at NSTX

    International Nuclear Information System (INIS)

    Sichta, P.; Dong, J.

    2002-01-01

    The NSTX achieved first plasma in 1999. The Experimental Physics and Industrial Control System (EPICS) is used to provide data-integration services for monitoring and control of all NSTX engineering subsystems. EPICS is a set of software initially developed at U.S. DOE laboratories. It is currently used and maintained through a global collaboration of hundreds of scientists and engineers. This paper will relate some of our experiences using and supporting the EPICS software. Topics include reliability and maintainability, lessons learned, recently added engineering subsystems, new EPICS software tools, and a review of our first EPICS software upgrade. Steps to modernize the technical infrastructure of EPICS to ensure effective support for NSTX will also be described

  15. Using lot quality-assurance sampling and area sampling to identify priority areas for trachoma control: Viet Nam.

    Science.gov (United States)

    Myatt, Mark; Mai, Nguyen Phuong; Quynh, Nguyen Quang; Nga, Nguyen Huy; Tai, Ha Huy; Long, Nguyen Hung; Minh, Tran Hung; Limburg, Hans

    2005-10-01

    To report on the use of lot quality-assurance sampling (LQAS) surveys undertaken within an area-sampling framework to identify priority areas for intervention with trachoma control activities in Viet Nam. The LQAS survey method for the rapid assessment of the prevalence of active trachoma was adapted for use in Viet Nam with the aim of classifying individual communes by the prevalence of active trachoma among children in primary school. School-based sampling was used; school sites to be sampled were selected using an area-sampling approach. A total of 719 communes in 41 districts in 18 provinces were surveyed. Survey staff found the LQAS survey method both simple and rapid to use after initial problems with area-sampling methods were identified and remedied. The method yielded a finer spatial resolution of prevalence than had been previously achieved in Viet Nam using semiquantitative rapid assessment surveys and multistage cluster-sampled surveys. When used with area-sampling techniques, the LQAS survey method has the potential to form the basis of survey instruments that can be used to efficiently target resources for interventions against active trachoma. With additional work, such methods could provide a generally applicable tool for effective programme planning and for the certification of the elimination of trachoma as a blinding disease.

  16. ITER Fast Plant System Controller prototype based on PXIe platform

    International Nuclear Information System (INIS)

    Ruiz, M.; Vega, J.; Castro, R.; Sanz, D.; López, J.M.; Arcas, G. de; Barrera, E.; Nieto, J.; Gonçalves, B.; Sousa, J.; Carvalho, B.; Utzel, N.; Makijarvi, P.

    2012-01-01

    Highlights: ► Implementation of Fast Plant System Controller (FPSC) for ITER CODAC. ► Efficient data acquisition and data movement using EPICS. ► Performance of PCIe technologies in the implementation of FPSC. - Abstract: The ITER Fast Plant System Controller (FPSC) is based on embedded technologies. The FPSC will be devoted to both data acquisition tasks (sampling rates higher than 1 kHz) and control purposes (feedback loop actuators). Some of the essential requirements of these systems are: (a) data acquisition and data preprocessing; (b) interfacing with different networks and high speed links (Plant Operation Network, timing network based on IEEE1588, synchronous data transference and streaming/archiving networks); and (c) system setup and operation using EPICS (Experimental Physics and Industrial Control System) process variables. CIEMAT and UPM have implemented a prototype of FPSC using a PXIe (PCI eXtension for Instrumentation) form factor in a R and D project developed in two phases. The paper presents the main features of the two prototypes developed that have been named alpha and beta. The former was implemented using LabVIEW development tools as it was focused on modeling the FPSC software modules, using the graphical features of LabVIEW applications, and measuring the basic performance in the system. The alpha version prototype implements data acquisition with time-stamping, EPICS monitoring using waveform process variables (PVs), and archiving. The beta version prototype is a complete IOC implemented using EPICS with different software functional blocks. These functional blocks are integrated and managed using an ASYN driver solution and provide the basic functionalities required by ITER FPSC such as data acquisition, data archiving, data pre-processing (using both CPU and GPU) and streaming.

  17. Integrating the Theory of Sampling into Underground Mine Grade Control Strategies

    Directory of Open Access Journals (Sweden)

    Simon C. Dominy

    2018-05-01

    Full Text Available Grade control in underground mines aims to deliver quality tonnes to the process plant via the accurate definition of ore and waste. It comprises a decision-making process including data collection and interpretation; local estimation; development and mining supervision; ore and waste destination tracking; and stockpile management. The foundation of any grade control programme is that of high-quality samples collected in a geological context. The requirement for quality samples has long been recognised, where they should be representative and fit-for-purpose. Once a sampling error is introduced, it propagates through all subsequent processes contributing to data uncertainty, which leads to poor decisions and financial loss. Proper application of the Theory of Sampling reduces errors during sample collection, preparation, and assaying. To achieve quality, sampling techniques must minimise delimitation, extraction, and preparation errors. Underground sampling methods include linear (chip and channel, grab (broken rock, and drill-based samples. Grade control staff should be well-trained and motivated, and operating staff should understand the critical need for grade control. Sampling must always be undertaken with a strong focus on safety and alternatives sought if the risk to humans is high. A quality control/quality assurance programme must be implemented, particularly when samples contribute to a reserve estimate. This paper assesses grade control sampling with emphasis on underground gold operations and presents recommendations for optimal practice through the application of the Theory of Sampling.

  18. Programming PLCS under EPICS at the SNS Project : Further Experiences in Collaboration

    International Nuclear Information System (INIS)

    P. A. Gurd; W. H. Strong; J. D. Creel

    2003-01-01

    The Spallation Neutron Source (SNS) is an accelerator-based neutron source being built in Tennessee by a partnership of six national laboratories. The control system components for the SNS were produced by personnel at the collaborating laboratories, by vendors of the equipment, and by commercial contractors. A number of different approaches were used to provide the programming for both the programmable logic controllers (PLCs) and the input-output controllers (IOCs) which were all based on the Experimental Physics and Industrial Control System (EPICS). For conventional facilities, both the PLCs and the IOCs were programmed under a commercial contract. The PLCs for the high power radio frequency system (HPRF) were programmed by the vendors of the equipment, while the IOCs were programmed by the collaborating laboratory. Finally, while the IOCs for the cryogenic systems were programmed at Oak Ridge, three different approaches were used to produce the PLC programming: some were programmed at Oak Ridge, some at TJNAF, and some at vendor sites. This paper discusses the status of the PLCs in the control system and the integration challenges encountered in the various approaches

  19. Integrating Gigabit ethernet cameras into EPICS at Diamond light source

    International Nuclear Information System (INIS)

    Cobb, T.

    2012-01-01

    At Diamond Light Source a range of cameras are used to provide images for diagnostic purposes in both the accelerator and photo beamlines. The accelerator and existing beamlines use Point Grey Flea and Flea2 Firewire cameras. We have selected Gigabit Ethernet cameras supporting GigE Vision for our new photon beamlines. GigE Vision is an interface standard for high speed Ethernet cameras which encourages inter-operability between manufacturers. This paper describes the challenges encountered while integrating GigE Vision cameras from a range of vendors into EPICS. GigE Vision cameras appear to be more reliable than the Firewire cameras, and the simple cabling makes much easier to move the cameras to different positions. Upcoming power over Ethernet versions of the cameras will reduce the number of cables still further

  20. Numerical and modeling techniques used in the EPIC code

    International Nuclear Information System (INIS)

    Pizzica, P.A.; Abramson, P.B.

    1977-01-01

    EPIC models fuel and coolant motion which result from internal fuel pin pressure (from fission gas or fuel vapor) and/or from the generation of sodium vapor pressures in the coolant channel subsequent to pin failure in an LMFBR. The modeling includes the ejection of molten fuel from the pin into a coolant channel with any amount of voiding through a clad rip which may be of any length or which may expand with time. One-dimensional Eulerian hydrodynamics is used to model both the motion of fuel and fission gas inside a molten fuel cavity and the mixture of two-phase sodium and fission gas in the channel. Motion of molten fuel particles in the coolant channel is tracked with a particle-in-cell technique

  1. Retrieving Smoke Aerosol Height from DSCOVR/EPIC

    Science.gov (United States)

    Xu, X.; Wang, J.; Wang, Y.

    2017-12-01

    Unlike industrial pollutant particles that are often confined within the planetary boundary layer, smoke from forest and agriculture fires can inject massive carbonaceous aerosols into the upper troposphere due to the intense pyro-convection. Sensitivity of weather and climate to absorbing carbonaceous aerosols is regulated by the altitude of those aerosol layers. However, aerosol height information remains limited from passive satellite sensors. Here we present an algorithm to estimate smoke aerosol height from radiances in the oxygen A and B bands measured by the Earth Polychromatic Imaging Camera (EPIC) from the Deep Space Climate Observatory (DSCOVR). With a suit of case studies and validation efforts, we demonstrate that smoke aerosol height can be well retrieved over both ocean and land surfaces multiple times daily.

  2. Radiation effects in wild terrestrial vertebrates - the EPIC collection.

    Science.gov (United States)

    Sazykina, Tatiana; Kryshev, Ivan I

    2006-01-01

    The paper presents data on radiation effects in populations of wild vertebrate animals inhabiting contaminated terrestrial ecosystems. The data were extracted from the database "Radiation effects on biota", compiled within the framework of the EC Project EPIC (2000-2003). The data collection, based on publications in Russian, demonstrates radiation effects in the areas characterized with high levels of radionuclides (Kyshtym radioactive trace; "spots" of enhanced natural radioactivity in the Komi region of Russia; territories contaminated from the Chernobyl fallout). The data covers a wide range of exposures from acute accidental irradiation to lifetime exposures at relatively low dose rates. Radiation effects include mortality, changes in reproduction, decrease of health, ecological effects, cytogenetic effects, adaptation to radiation, and others. Peculiarities of radiation effects caused by different radionuclides are described, also the severity of effects as they appear in different organisms (e.g. mice, frogs, birds, etc.).

  3. Radiation effects in wild terrestrial vertebrates - the EPIC collection

    International Nuclear Information System (INIS)

    Sazykina, Tatiana; Kryshev, Ivan I.

    2006-01-01

    The paper presents data on radiation effects in populations of wild vertebrate animals inhabiting contaminated terrestrial ecosystems. The data were extracted from the database 'Radiation effects on biota', compiled within the framework of the EC Project EPIC (2000-2003). The data collection, based on publications in Russian, demonstrates radiation effects in the areas characterized with high levels of radionuclides (Kyshtym radioactive trace; 'spots' of enhanced natural radioactivity in the Komi region of Russia; territories contaminated from the Chernobyl fallout). The data covers a wide range of exposures from acute accidental irradiation to lifetime exposures at relatively low dose rates. Radiation effects include mortality, changes in reproduction, decrease of health, ecological effects, cytogenetic effects, adaptation to radiation, and others. Peculiarities of radiation effects caused by different radionuclides are described, also the severity of effects as they appear in different organisms (e.g. mice, frogs, birds, etc.)

  4. Vegetation Earth System Data Record from DSCOVR EPIC Observations

    Science.gov (United States)

    Knyazikhin, Y.; Song, W.; Yang, B.; Mottus, M.; Rautiainen, M.; Stenberg, P.

    2017-12-01

    The NASA's Earth Polychromatic Imaging Camera (EPIC) onboard NOAA's Deep Space Climate Observatory (DSCOVR) mission was launched on February 11, 2015 to the Sun-Earth Lagrangian L1 point where it began to collect radiance data of the entire sunlit Earth every 65 to 110 min in June 2015. It provides imageries in near backscattering directions with the scattering angle between 168° and 176° at ten ultraviolet to near infrared (NIR) narrow spectral bands centered at 317.5 (band width 1.0) nm, 325.0 (2.0) nm, 340.0 (3.0) nm, 388.0 (3.0) nm, 433.0 (3.0) nm, 551.0 (3.0) nm, 680.0 (3.0) nm, 687.8 (0.8) nm, 764.0 (1.0) nm and 779.5 (2.0) nm. This poster presents current status of the Vegetation Earth System Data Record of global Leaf Area Index (LAI), solar zenith angle dependent Sunlit Leaf Area Index (SLAI), Fraction vegetation absorbed Photosynthetically Active Radiation (FPAR) and Normalized Difference Vegetation Index (NDVI) derived from the DSCOVR EPIC observations. Whereas LAI is a standard product of many satellite missions, the SLAI is a new satellite-derived parameter. Sunlit and shaded leaves exhibit different radiative response to incident Photosynthetically Active Radiation (400-700 nm), which in turn triggers various physiological and physical processes required for the functioning of plants. FPAR, LAI and SLAI are key state parameters in most ecosystem productivity models and carbon/nitrogen cycle. The product at 10 km sinusoidal grid and 65 to 110 min temporal frequency as well as accompanying Quality Assessment (QA) variables will be publicly available from the NASA Langley Atmospheric Science Data Center. The Algorithm Theoretical Basis (ATBD) and product validation strategy are also discussed in this poster.

  5. Nitrous Oxide Emissions from Biofuel Crops and Parameterization in the EPIC Biogeochemical Model

    Science.gov (United States)

    This presentation describes year 1 field measurements of N2O fluxes and crop yields which are used to parameterize the EPIC biogeochemical model for the corresponding field site. Initial model simulations are also presented.

  6. Prospect-EPIC Utrecht: Study design and characteristics of the cohort population

    NARCIS (Netherlands)

    Boker, L.K.; Noord, P.A.H. van; Schouw, Y.T. van der; Koot, V.C.M.; Bueno-de-Mesquita, H.B.; Riboli, E.; Grobbee, D.E.; Peeters, P.H.M.

    2001-01-01

    The European Prospective Investigation into Cancer and Nutrition (EPIC), which hasbe en established in order to investigate the relations between nutrition and cancer, wasinitiated in 1990 and involves10 European countrieswith heterogeneous dietary patternsand differing cancer incidence rates. This

  7. Exploring Lyric, Epic, and Dramatic Voices: Stages of Incandescence in the Poetry of the Aged.

    Science.gov (United States)

    Reed, M. Ann

    1992-01-01

    Identifies true relationships between the psyche and the lyric, epic, and dramatic voices of poetry. Shows how the acts of identifying, responding to, and composing in these three voices engage healing, inspiration, and active imagination among the aging. (SR)

  8. Startup of the experimental physics industrial control system at NSTX

    International Nuclear Information System (INIS)

    Sichta, P.; Dong, J.

    1999-01-01

    The Experimental Physics Industrial Control System (EPICS) is a set of software which is being used as the basis of the National Spherical Torus Experiment's (NSTX) Process Control System, a major element of the NSTX's Central Instrumentation and Control System. EPICS is a result of a co-development effort started by several US Department of Energy National Laboratories. EPICS is actively supported through an international collaboration made up of government and industrial users. EPICS' good points include portability, scalability, and extensibility. A drawback for small experiments is that a wide range of software skills are necessary to get the software tools running for the process engineers. The authors' experience in designing, developing, operating, and maintaining NSTX's EPICS (system) will be reviewed

  9. Replica sizing strategy for aortic valve replacement improves haemodynamic outcome of the epic supra valve.

    Science.gov (United States)

    Gonzalez-Lopez, David; Faerber, Gloria; Diab, Mahmoud; Amorim, Paulo; Zeynalov, Natig; Doenst, Torsten

    2017-10-01

    Current sizing strategies suggest valve selection based on annulus diameter despite supra-annular placement of biological prostheses potentially allowing placement of a larger size. We assessed the frequency of selecting a larger prosthesis if prosthesis size was selected using a replica (upsizing) and evaluated its impact on haemodynamics. We analysed all discharge echocardiograms between June 2012 and June 2014, where a replica sizer was used for isolated aortic valve replacement (Epic Supra: 266 patients, Trifecta: 49 patients). Upsizing was possible in 71% of the Epic Supra valves (by 1 size: 168, by 2 sizes: 20) and in 59% of the Trifectas (by 1 size: 26, by 2 sizes: 3). Patients for whom upsizing was possible had the lowest pressure gradients within their annulus size groups. The difference was significant in annulus diameters of 21-22 or 25-26 mm (Epic Supra) and 23-24 mm (Trifecta). Trifecta gradients were the lowest. However, the ability to upsize the Epic Supra by 2 sizes eliminated the differences between Epic Supra and Trifecta. Upsizing did not cause intraoperative complications. Using replica sizers for aortic prosthesis size selection allows the implantation of bigger prostheses than recommended in most cases and reduces postoperative gradients, specifically for Epic Supra. © The Author 2017. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

  10. The EPIC nutrient database project (ENDB): a first attempt to standardize nutrient databases across the 10 European countries participating in the EPIC study

    DEFF Research Database (Denmark)

    Slimani, N.; Deharveng, G.; Unwin, I.

    2007-01-01

    because there is currently no European reference NDB available. Design: A large network involving national compilers, nutritionists and experts on food chemistry and computer science was set up for the 'EPIC Nutrient DataBase' ( ENDB) project. A total of 550-1500 foods derived from about 37 000...... standardized EPIC 24-h dietary recalls (24-HDRS) were matched as closely as possible to foods available in the 10 national NDBs. The resulting national data sets ( NDS) were then successively documented, standardized and evaluated according to common guidelines and using a DataBase Management System...

  11. 27 CFR 27.75 - Samples of distilled spirits, wine, and beer for quality control purposes.

    Science.gov (United States)

    2010-04-01

    ... spirits, wine, and beer for quality control purposes. 27.75 Section 27.75 Alcohol, Tobacco Products and... DISTILLED SPIRITS, WINES, AND BEER General Requirements Exemptions § 27.75 Samples of distilled spirits, wine, and beer for quality control purposes. Samples of distilled spirits, wine, and beer in containers...

  12. Maximum likelihood estimation for Cox's regression model under nested case-control sampling

    DEFF Research Database (Denmark)

    Scheike, Thomas; Juul, Anders

    2004-01-01

    Nested case-control sampling is designed to reduce the costs of large cohort studies. It is important to estimate the parameters of interest as efficiently as possible. We present a new maximum likelihood estimator (MLE) for nested case-control sampling in the context of Cox's proportional hazard...

  13. Design, analysis, and interpretation of field quality-control data for water-sampling projects

    Science.gov (United States)

    Mueller, David K.; Schertz, Terry L.; Martin, Jeffrey D.; Sandstrom, Mark W.

    2015-01-01

    The process of obtaining and analyzing water samples from the environment includes a number of steps that can affect the reported result. The equipment used to collect and filter samples, the bottles used for specific subsamples, any added preservatives, sample storage in the field, and shipment to the laboratory have the potential to affect how accurately samples represent the environment from which they were collected. During the early 1990s, the U.S. Geological Survey implemented policies to include the routine collection of quality-control samples in order to evaluate these effects and to ensure that water-quality data were adequately representing environmental conditions. Since that time, the U.S. Geological Survey Office of Water Quality has provided training in how to design effective field quality-control sampling programs and how to evaluate the resultant quality-control data. This report documents that training material and provides a reference for methods used to analyze quality-control data.

  14. A microcomputer controlled sample changer system for γ-ray spectroscopy

    International Nuclear Information System (INIS)

    Jost, D.T.; Kraehenbuehl, U.; Gunten, H.R. von

    1982-01-01

    A Z-80 based microcomputer is used to control a sample changer system connected to two γ-ray spectrometers. Samples are changed according to preselected counting criteria (maximum time and/or desired precision). Special precautions were taken to avoid the loss of information and of samples in case of a power failure. (orig.)

  15. Adaptive sampling rate control for networked systems based on statistical characteristics of packet disordering.

    Science.gov (United States)

    Li, Jin-Na; Er, Meng-Joo; Tan, Yen-Kheng; Yu, Hai-Bin; Zeng, Peng

    2015-09-01

    This paper investigates an adaptive sampling rate control scheme for networked control systems (NCSs) subject to packet disordering. The main objectives of the proposed scheme are (a) to avoid heavy packet disordering existing in communication networks and (b) to stabilize NCSs with packet disordering, transmission delay and packet loss. First, a novel sampling rate control algorithm based on statistical characteristics of disordering entropy is proposed; secondly, an augmented closed-loop NCS that consists of a plant, a sampler and a state-feedback controller is transformed into an uncertain and stochastic system, which facilitates the controller design. Then, a sufficient condition for stochastic stability in terms of Linear Matrix Inequalities (LMIs) is given. Moreover, an adaptive tracking controller is designed such that the sampling period tracks a desired sampling period, which represents a significant contribution. Finally, experimental results are given to illustrate the effectiveness and advantages of the proposed scheme. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

  16. Note: Design and development of wireless controlled aerosol sampling network for large scale aerosol dispersion experiments

    International Nuclear Information System (INIS)

    Gopalakrishnan, V.; Subramanian, V.; Baskaran, R.; Venkatraman, B.

    2015-01-01

    Wireless based custom built aerosol sampling network is designed, developed, and implemented for environmental aerosol sampling. These aerosol sampling systems are used in field measurement campaign, in which sodium aerosol dispersion experiments have been conducted as a part of environmental impact studies related to sodium cooled fast reactor. The sampling network contains 40 aerosol sampling units and each contains custom built sampling head and the wireless control networking designed with Programmable System on Chip (PSoC™) and Xbee Pro RF modules. The base station control is designed using graphical programming language LabView. The sampling network is programmed to operate in a preset time and the running status of the samplers in the network is visualized from the base station. The system is developed in such a way that it can be used for any other environment sampling system deployed in wide area and uneven terrain where manual operation is difficult due to the requirement of simultaneous operation and status logging

  17. Note: Design and development of wireless controlled aerosol sampling network for large scale aerosol dispersion experiments

    Energy Technology Data Exchange (ETDEWEB)

    Gopalakrishnan, V.; Subramanian, V.; Baskaran, R.; Venkatraman, B. [Radiation Impact Assessment Section, Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India)

    2015-07-15

    Wireless based custom built aerosol sampling network is designed, developed, and implemented for environmental aerosol sampling. These aerosol sampling systems are used in field measurement campaign, in which sodium aerosol dispersion experiments have been conducted as a part of environmental impact studies related to sodium cooled fast reactor. The sampling network contains 40 aerosol sampling units and each contains custom built sampling head and the wireless control networking designed with Programmable System on Chip (PSoC™) and Xbee Pro RF modules. The base station control is designed using graphical programming language LabView. The sampling network is programmed to operate in a preset time and the running status of the samplers in the network is visualized from the base station. The system is developed in such a way that it can be used for any other environment sampling system deployed in wide area and uneven terrain where manual operation is difficult due to the requirement of simultaneous operation and status logging.

  18. Continuity with Creole Epic and Innovation in the «History of New Mexico», 1610

    Directory of Open Access Journals (Sweden)

    Pedro Cebollero

    2017-11-01

    Full Text Available This is an introductory study to Gaspar de Villagrá’s History of New Mexico (1610 in the context of the Cortés epic cycle tradition. The concept of «epic continuity» is utilized in order to better understand how the poem adheres to epic tradition at the same time that it goes through formal changes needed for its renovation. Part of the renovation is the inclusion of prose as a legal defense strategy, and its use as a vehicle for the struggles of Mexican Creoles. It is proposed that this poem belongs in a Frontier Creole epic sub-cycle.

  19. EPIC Calibration/Validation Experiment Field Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Koch, Steven E [National Severe Storm Laboratory/NOAA; Chilson, Phillip [University of Oklahoma; Argrow, Brian [University of Colorado

    2017-03-15

    A field exercise involving several different kinds of Unmanned Aerial Systems (UAS) and supporting instrumentation systems provided by DOE/ARM and NOAA/NSSL was conducted at the ARM SGP site in Lamont, Oklahoma on 29-30 October 2016. This campaign was part of a larger National Oceanic and Atmospheric Administration (NOAA) UAS Program Office program awarded to the National Severe Storms Laboratory (NSSL). named Environmental Profiling and Initiation of Convection (EPIC). The EPIC Field Campaign (Test and Calibration/Validation) proposed to ARM was a test or “dry-run” for a follow-up campaign to be requested for spring/summer 2017. The EPIC project addresses NOAA’s objective to “evaluate options for UAS profiling of the lower atmosphere with applications for severe weather.” The project goal is to demonstrate that fixed-wing and rotary-wing small UAS have the combined potential to provide a unique observing system capable of providing detailed profiles of temperature, moisture, and winds within the atmospheric boundary layer (ABL) to help determine the potential for severe weather development. Specific project objectives are: 1) to develop small UAS capable of acquiring needed wind and thermodynamic profiles and transects of the ABL using one fixed-wing UAS operating in tandem with two different fixed rotary-wing UAS pairs; 2) adapt and test miniaturized, high-precision, and fast-response atmospheric sensors with high accuracy in strong winds characteristic of the pre-convective ABL in Oklahoma; 3) conduct targeted short-duration experiments at the ARM Southern Great Plains site in northern Oklahoma concurrently with a second site to be chosen in “real-time” from the Oklahoma Mesonet in coordination with the (National Weather Service (NWS)-Norman Forecast Office; and 4) gain valuable experience in pursuit of NOAA’s goals for determining the value of airborne, mobile observing systems for monitoring rapidly evolving high-impact severe weather

  20. The CEBAF control system

    International Nuclear Information System (INIS)

    Watson, W.A. III.

    1995-01-01

    CEBAF has recently upgraded its accelerator control system to use EPICS, a control system toolkit being developed by a collaboration among laboratories in the US and Europe. The migration to EPICS has taken place during a year of intense commissioning activity, with new and old control systems operating concurrently. Existing CAMAC hardware was preserved by adding a CAMAC serial highway link to VME; newer hardware developments are now primarily in VME. Software is distributed among three tiers of computers: first, workstations and X terminals for operator interfaces and high level applications; second, VME single board computers for distributed access to hardware and for local control processing; third, embedded processors where needed for faster closed loop operation. This system has demonstrated the ability to scale EPICS to controlling thousands of devices, including hundreds of embedded processors, with control distributed among dozens of VME processors executing more than 125,000 EPICS database records. To deal with the large size of the control system, CEBAF has integrated an object oriented database, providing data management capabilities for both low level I/O and high level machine modeling. A new callable interface which is control system independent permits access to live EPICS data, data in other Unix processes, and data contained in the object oriented database

  1. Automatic sample changer control software for automation of neutron activation analysis process in Malaysian Nuclear Agency

    Science.gov (United States)

    Yussup, N.; Ibrahim, M. M.; Rahman, N. A. A.; Mokhtar, M.; Salim, N. A. A.; Soh@Shaari, S. C.; Azman, A.; Lombigit, L.; Azman, A.; Omar, S. A.

    2018-01-01

    Most of the procedures in neutron activation analysis (NAA) process that has been established in Malaysian Nuclear Agency (Nuclear Malaysia) since 1980s were performed manually. These manual procedures carried out by the NAA laboratory personnel are time consuming and inefficient especially for sample counting and measurement process. The sample needs to be changed and the measurement software needs to be setup for every one hour counting time. Both of these procedures are performed manually for every sample. Hence, an automatic sample changer system (ASC) that consists of hardware and software is developed to automate sample counting process for up to 30 samples consecutively. This paper describes the ASC control software for NAA process which is designed and developed to control the ASC hardware and call GammaVision software for sample measurement. The software is developed by using National Instrument LabVIEW development package.

  2. A New Attribute Control Chart using Multiple Dependent State Repetitive Sampling

    KAUST Repository

    Aldosari, Mansour Sattam; Aslam, Muhammad; Jun, Chi-Hyuck

    2017-01-01

    In this manuscript, a new attribute control chart using multiple dependent state repetitive sampling is designed. The operational procedure and structure of the proposed control chart is given. The required measures to determine the average run length (ARL) for in-control and out-of-control processes are given. Tables of ARLs are reported for various control chart parameters. The proposed control chart is more sensitive in detecting a small shift in the process as compared to the existing attribute control charts. The simulation study shows the efficiency of the proposed chart over the existing charts. An example is given for the illustration purpose.

  3. A New Attribute Control Chart using Multiple Dependent State Repetitive Sampling

    KAUST Repository

    Aldosari, Mansour Sattam

    2017-03-25

    In this manuscript, a new attribute control chart using multiple dependent state repetitive sampling is designed. The operational procedure and structure of the proposed control chart is given. The required measures to determine the average run length (ARL) for in-control and out-of-control processes are given. Tables of ARLs are reported for various control chart parameters. The proposed control chart is more sensitive in detecting a small shift in the process as compared to the existing attribute control charts. The simulation study shows the efficiency of the proposed chart over the existing charts. An example is given for the illustration purpose.

  4. The impact of overactive bladder, incontinence and other lower urinary tract symptoms on quality of life, work productivity, sexuality and emotional well-being in men and women: results from the EPIC study.

    Science.gov (United States)

    Coyne, Karin S; Sexton, Chris C; Irwin, Debra E; Kopp, Zoe S; Kelleher, Con J; Milsom, Ian

    2008-06-01

    To examine the effect overactive bladder (OAB) and other lower urinary tract symptoms (LUTS) on health-related quality of life (HRQoL) in a population sample, as OAB often occurs in conjunction with many other LUTS. A nested case-control analysis was performed on men and women with (cases) and without (controls) OAB, from the EPIC study. OAB was assessed using 2002 International Continence Society definitions. Based on their responses to questions about LUTS, cases were classified into five groups; continent OAB, OAB with incontinence, OAB + postmicturition, OAB + voiding, and OAB + postmicturition + voiding. Both cases and controls were asked questions about symptom bother (OAB-q), generic QoL (EQ-5D), work productivity (Work Productivity and Activity Impairment, WPAI), depressive symptoms (Center for Epidemiologic Studies Depression Scale), sexual satisfaction, and erectile dysfunction (men only) using the Massachusetts Male Aging Study. Cases answered additional condition-specific questions HRQoL (OAB-q short form), Patient Perception of Bladder Condition and work productivity related to a specific health problem (WPAI-SHP). General linear models were used to evaluate group differences. Of the EPIC participants, 1434 identified OAB cases were matched by age, gender and country, with 1434 participants designated as controls. Cases and controls were primarily Caucasian (96.2% and 96.7%, respectively), and most (65%) were female; the mean age was 53.8 and 53.7 years, respectively. Comorbid conditions differed significantly by case/control status, with cases reporting significantly greater rates of chronic constipation, asthma, diabetes, high blood pressure, bladder or prostate cancer, neurological conditions and depression. There were significant differences between the cases and controls in all reported LUTS. The OAB + postmicturition + voiding group reported significantly greater symptom bother, worse HRQoL, higher rates of depression and decreased enjoyment of

  5. A Client/Server Architecture for Supporting Science Data Using EPICS Version 4

    Energy Technology Data Exchange (ETDEWEB)

    Dalesio, Leo [EPIC Consulting, Jacksonville, FL (United States)

    2015-04-21

    The Phase 1 grant that serves as a precursor to this proposal, prototyped complex storage techniques for high speed structured data that is being produced in accelerator diagnostics and beam line experiments. It demonstrates the technologies that can be used to archive and retrieve complex data structures and provide the performance required by our new accelerators, instrumentations, and detectors. Phase 2 is proposed to develop a high-performance platform for data acquisition and analysis to provide physicists and operators a better understanding of the beam dynamics. This proposal includes developing a platform for reading 109 MHz data at 10 KHz rates through a multicore front end processor, archiving the data to an archive repository that is then indexed for fast retrieval. The data is then retrieved from this data archive, integrated with the scalar data, to provide data sets to client applications for analysis, use in feedback, and to aid in identifying problem with the instrumentation, plant, beam steering, or model. This development is built on EPICS version 4 , which is being successfully deployed to implement physics applications. Through prior SBIR grants, EPICS version 4 has a solid communication protocol for middle layer services (PVAccess), structured data representation and methods for efficient transportation and access (PVData), an operational hierarchical record environment (JAVA IOC), and prototypes for standard structured data (Normative Types). This work was further developed through project funding to successfully deploy the first service based physics application environment with demonstrated services that provide arbitrary object views, save sets, model, lattice, and unit conversion. Thin client physics applications have been developed in Python that implement quad centering, orbit display, bump control, and slow orbit feedback. This service based architecture has provided a very modular and robust environment that enables commissioning teams

  6. Exploiting H infinity sampled-data control theory for high-precision electromechanical servo control design

    NARCIS (Netherlands)

    Oomen, T.A.E.; Wal, van de M.M.J.; Bosgra, O.H.

    2006-01-01

    Optimal design of digital controllers for industrial electromechanical servo systems using an Hinf-criterion is considered. Present industrial practice is to perform the control design in the continuous time domain and to discretize the controller a posteriori. This procedure involves unnecessary

  7. Creating an EPICS Based Test Stand Development System for a BPM Digitizer of the Linac Coherent Light Source

    International Nuclear Information System (INIS)

    2011-01-01

    The Linac Coherent Light Source (LCLS) is required to deliver a high quality electron beam for producing coherent X-rays. As a result, high resolution beam position monitoring is required. The Beam Position Monitor (BPM) digitizer acquires analog signals from the beam line and digitizes them to obtain beam position data. Although Matlab is currently being used to test the BPM digitizer?s functions and capability, the Controls Department at SLAC prefers to use Experimental Physics and Industrial Control Systems (EPICS). This paper discusses the transition of providing similar as well as enhanced functionalities, than those offered by Matlab, to test the digitizer. Altogether, the improved test stand development system can perform mathematical and statistical calculations with the waveform signals acquired from the digitizer and compute the fast Fourier transform (FFT) of the signals. Finally, logging of meaningful data into files has been added.

  8. Continuous quality control of the blood sampling procedure using a structured observation scheme

    DEFF Research Database (Denmark)

    Seemann, T. L.; Nybo, M.

    2015-01-01

    Background: An important preanalytical factor is the blood sampling procedure and its adherence to the guidelines, i.e. CLSI and ISO 15189, in order to ensure a consistent quality of the blood collection. Therefore, it is critically important to introduce quality control on this part of the process....... As suggested by the EFLM working group on the preanalytical phase we introduced continuous quality control of the blood sampling procedure using a structured observation scheme to monitor the quality of blood sampling performed on an everyday basis. Materials and methods: Based on our own routines the EFLM....... Conclusion: It is possible to establish a continuous quality control on blood sampling. It has been well accepted by the staff and we have already been able to identify critical areas in the sampling process. We find that continuous auditing increase focus on the quality of blood collection which ensures...

  9. Quantitative food intake in the EPIC-Germany cohorts. European Investigation into Cancer and Nutrition.

    Science.gov (United States)

    Schulze, M B; Brandstetter, B R; Kroke, A; Wahrendorf, J; Boeing, H

    1999-01-01

    The EPIC-Heidelberg and the EPIC-Potsdam studies with about 53,000 study participants represent the German contribution to the EPIC (European Investigation into Cancer and Nutrition) cohort study. Within the EPIC study, standardized 24-hour dietary recalls were applied as a quantitative calibration method in order to estimate the amount of scaling bias introduced by the varying center-specific dietary assessment methods. This article presents intake of food items and food groups in the two German cohorts estimated by 24-hour quantitative dietary recalls. Recalls from 1,013 men and 1,078 women in Heidelberg and 1,032 men and 898 women in Potsdam were included in the analysis. The intake of recorded food items or recipe ingredients as well as fat used for cooking was summarized into 16 main food groups and a variety of different subgroups stratified by sex and weighted for the day of the week and age. In more than 90% of the recalls, consumption of dairy products, cereals and cereal products, bread, fat, and non-alcoholic beverages, particularly coffee/tea, was reported. Inter-cohort evaluations revealed that bread, potatoes, fruit and fat were consumed in higher amounts in the Potsdam cohort while the opposite was found for pasta/rice, non-alcoholic, and alcoholic beverages. It was concluded that the exposure variation was increased by having two instead of one EPIC study centers in Germany. Copyright 1999 S. Karger AG, Basel

  10. Uncertainties in cloud phase and optical thickness retrievals from the Earth Polychromatic Imaging Camera (EPIC)

    Science.gov (United States)

    Meyer, Kerry; Yang, Yuekui; Platnick, Steven

    2018-01-01

    This paper presents an investigation of the expected uncertainties of a single channel cloud optical thickness (COT) retrieval technique, as well as a simple cloud temperature threshold based thermodynamic phase approach, in support of the Deep Space Climate Observatory (DSCOVR) mission. DSCOVR cloud products will be derived from Earth Polychromatic Imaging Camera (EPIC) observations in the ultraviolet and visible spectra. Since EPIC is not equipped with a spectral channel in the shortwave or mid-wave infrared that is sensitive to cloud effective radius (CER), COT will be inferred from a single visible channel with the assumption of appropriate CER values for liquid and ice phase clouds. One month of Aqua MODIS daytime granules from April 2005 is selected for investigating cloud phase sensitivity, and a subset of these granules that has similar EPIC sun-view geometry is selected for investigating COT uncertainties. EPIC COT retrievals are simulated with the same algorithm as the operational MODIS cloud products (MOD06), except using fixed phase-dependent CER values. Uncertainty estimates are derived by comparing the single channel COT retrievals with the baseline bi-spectral MODIS retrievals. Results show that a single channel COT retrieval is feasible for EPIC. For ice clouds, single channel retrieval errors are minimal (clouds the error is mostly limited to within 10%, although for thin clouds (COT cloud masking and cloud temperature retrievals are not considered in this study. PMID:29619116

  11. Preparation and analysis of standardized waste samples for Controlled Ecological Life Support Systems (CELSS)

    Science.gov (United States)

    Carden, J. L.; Browner, R.

    1982-01-01

    The preparation and analysis of standardized waste samples for controlled ecological life support systems (CELSS) are considered. Analysis of samples from wet oxidation experiments, the development of ion chromatographic techniques utilizing conventional high pressure liquid chromatography (HPLC) equipment, and an investigation of techniques for interfacing an ion chromatograph (IC) with an inductively coupled plasma optical emission spectrometer (ICPOES) are discussed.

  12. Sampling methods to the statistical control of the production of blood components.

    Science.gov (United States)

    Pereira, Paulo; Seghatchian, Jerard; Caldeira, Beatriz; Santos, Paula; Castro, Rosa; Fernandes, Teresa; Xavier, Sandra; de Sousa, Gracinda; de Almeida E Sousa, João Paulo

    2017-12-01

    The control of blood components specifications is a requirement generalized in Europe by the European Commission Directives and in the US by the AABB standards. The use of a statistical process control methodology is recommended in the related literature, including the EDQM guideline. The control reliability is dependent of the sampling. However, a correct sampling methodology seems not to be systematically applied. Commonly, the sampling is intended to comply uniquely with the 1% specification to the produced blood components. Nevertheless, on a purely statistical viewpoint, this model could be argued not to be related to a consistent sampling technique. This could be a severe limitation to detect abnormal patterns and to assure that the production has a non-significant probability of producing nonconforming components. This article discusses what is happening in blood establishments. Three statistical methodologies are proposed: simple random sampling, sampling based on the proportion of a finite population, and sampling based on the inspection level. The empirical results demonstrate that these models are practicable in blood establishments contributing to the robustness of sampling and related statistical process control decisions for the purpose they are suggested for. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Varieties of Stimulus Control in Matching-to-Sample: A Kernel Analysis

    Science.gov (United States)

    Fields, Lanny; Garruto, Michelle; Watanabe, Mari

    2010-01-01

    Conditional discrimination or matching-to-sample procedures have been used to study a wide range of complex psychological phenomena with infrahuman and human subjects. In most studies, the percentage of trials in which a subject selects the comparison stimulus that is related to the sample stimulus is used to index the control exerted by the…

  14. The standardized computerized 24-h dietary recall method EPIC-Soft adapted for pan-European dietary monitoring

    DEFF Research Database (Denmark)

    Slimani, N.; Casagrande, C.; Nicolas, G.

    2011-01-01

    monitoring. Within European Food Consumption Validation (EFCOVAL), EPIC-Soft was adapted and further developed on various aspects that were required to optimize its use. In this paper, we present the structure and main interview steps of the EPIC-Soft program, after implementation of a series of new...

  15. Computer graphics for quality control in the INAA of geological samples

    International Nuclear Information System (INIS)

    Grossman, J.N.; Baedecker, P.A.

    1987-01-01

    A data reduction system for the routine instrumental activation analysis of samples is described, with particular emphasis on interactive graphics capabilities for evaluating analytical quality. Graphics procedures were developed to interactively control the analysis of selected photopeaks during spectral analysis, and to evaluate detector performance during a given counting cycle. Graphics algorithms are also used to compare the data on reference samples with accepted values, to prepare quality control charts to evaluate long term precision and to search for systematic variations in data on reference samples as a function of time. (author)

  16. Computer graphics for quality control in the INAA of geological samples

    Science.gov (United States)

    Grossman, J.N.; Baedecker, P.A.

    1987-01-01

    A data reduction system for the routine instrumental activation analysis of samples is described, with particular emphasis on interactive graphics capabilities for evaluating analytical quality. Graphics procedures have been developed to interactively control the analysis of selected photopeaks during spectral analysis, and to evaluate detector performance during a given counting cycle. Graphics algorithms are also used to compare the data on reference samples with accepted values, to prepare quality control charts to evaluate long term precision and to search for systematic variations in data on reference samples as a function of time. ?? 1987 Akade??miai Kiado??.

  17. An Experience Sampling Study of Learning, Affect, and the Demands Control Support Model

    Science.gov (United States)

    Daniels, Kevin; Boocock, Grahame; Glover, Jane; Hartley, Ruth; Holland, Julie

    2009-01-01

    The demands control support model (R. A. Karasek & T. Theorell, 1990) indicates that job control and social support enable workers to engage in problem solving. In turn, problem solving is thought to influence learning and well-being (e.g., anxious affect, activated pleasant affect). Two samples (N = 78, N = 106) provided data up to 4 times per…

  18. A method to encapsulate model structural uncertainty in ensemble projections of future climate: EPIC v1.0

    Science.gov (United States)

    Lewis, Jared; Bodeker, Greg E.; Kremser, Stefanie; Tait, Andrew

    2017-12-01

    computationally efficient than running multiple GCM or RCM simulations. Such a large ensemble of projections permits a description of a probability density function (PDF) of future climate states rather than a small number of individual story lines within that PDF, which may not be representative of the PDF as a whole; the EPIC method largely corrects for such potential sampling biases. The method is useful for providing projections of changes in climate to users wishing to investigate the impacts and implications of climate change in a probabilistic way. A web-based tool, using the EPIC method to provide probabilistic projections of changes in daily maximum and minimum temperatures for New Zealand, has been developed and is described in this paper.

  19. Synchrotron Radiation Beam Line of Piezoelectric Monochromator Control

    International Nuclear Information System (INIS)

    Ye Shengan; LIU Ping; Zheng Lifang

    2009-01-01

    It describes a Piezo Amplifier and Servo-controller module applied in the LN2-cooled Monochromator control system. The application of RS232 communication based on EPICS software environment and its software are implemented. (authors)

  20. Controlled cooling versus rapid freezing of teratozoospermic semen samples: Impact on sperm chromatin integrity

    Directory of Open Access Journals (Sweden)

    Shivananda N Kalludi

    2011-01-01

    Full Text Available Aim: The present study evaluates the impact of controlled slow cooling and rapid freezing techniques on the sperm chromatin integrity in teratozoospermic and normozoospermic samples. Setting: The study was done in a university infertility clinic, which is a tertiary healthcare center serving the general population. Design: It was a prospective study designed in vitro. Materials and Methods: Semen samples from normozoospermic (N=16 and teratozoospermic (N=13 infertile men were cryopreserved using controlled cooling and rapid freezing techniques. The sperm chromatin integrity was analyzed in fresh and frozen-thawed samples. Statistical Analysis Used: Data were reported as mean and standard error (mean ± SEM of mean. The difference between two techniques was determined by a paired t-test. Results: The freeze-thaw induced chromatin denaturation was significantly (P<0.01 elevated in the post-thaw samples of normozoospermic and teratozoospermic groups. Compared to rapid freezing, there was no difference in the number of red sperms (with DNA damage by the controlled slow cooling method in both normozoospermic and teratozoospermic groups. Freeze-thaw induced sperm chromatin denaturation in teratozoospermic samples did not vary between controlled slow cooling and rapid freezing techniques. Conclusions: Since the controlled slow cooling technique involves the use of expensive instrument and is a time consuming protocol, rapid freezing can be a good alternative technique for teratozoospermic and normozoospermic samples when sperm DNA damage is a concern.

  1. Sample size reassessment for a two-stage design controlling the false discovery rate.

    Science.gov (United States)

    Zehetmayer, Sonja; Graf, Alexandra C; Posch, Martin

    2015-11-01

    Sample size calculations for gene expression microarray and NGS-RNA-Seq experiments are challenging because the overall power depends on unknown quantities as the proportion of true null hypotheses and the distribution of the effect sizes under the alternative. We propose a two-stage design with an adaptive interim analysis where these quantities are estimated from the interim data. The second stage sample size is chosen based on these estimates to achieve a specific overall power. The proposed procedure controls the power in all considered scenarios except for very low first stage sample sizes. The false discovery rate (FDR) is controlled despite of the data dependent choice of sample size. The two-stage design can be a useful tool to determine the sample size of high-dimensional studies if in the planning phase there is high uncertainty regarding the expected effect sizes and variability.

  2. Implementation of the Integrated Alarm System for KOMAC facility using EPICS framework and Eclipse

    International Nuclear Information System (INIS)

    Song, Young-Gi; Kim, Jae-Ha; Kim, Han-Sung; Kwon, Hyeok-Jung; Cho, Yong-Sub

    2017-01-01

    The alarm detecting layer is the component that monitors alarm signals which are transported to the processing part through message queue. The main purpose of the processing part is to transfer the alarm signals connecting an alarm identification and state of the alarm to database system. The operation interface of system level signal links has been developed by EPICS framework. EPICS tools have been used for monitoring device alarm status. The KOMAC alarm system was developed for offering a user-friendly, intuitive user interface. The alarm system is implemented with EPICS IOC for alarm server, eclipse-mars integrated development tool for alarm viewer, and mariadb for alarm log. The new alarm system supports intuitive user interface on alarm information and alarm history. Alarm view has plans to add login function, user permission on alarm acknowledge, user permission of PV import, search and report function.

  3. Electrokinetic control of sample splitting at a channel bifurcation using isotachophoresis

    International Nuclear Information System (INIS)

    Persat, Alexandre; Santiago, Juan G

    2009-01-01

    We present a novel method for accurately splitting ionic samples at microchannel bifurcations. We leverage isotachophoresis (ITP) to focus and transport sample through a one-inlet, two-outlet microchannel bifurcation. We actively control the proportion of splitting by controlling potentials at end-channel reservoirs (and thereby controlling the current ratio). We explore the effect of buffer chemistry and local electric field on splitting dynamics and propose and validate a simple Kirchoff-type rule controlling the split ratio. We explore the effects of large applied electric fields on sample splitting and attribute a loss of splitting accuracy to electrohydrodynamic instabilities. We propose a scaling analysis to characterize the onset of this instability. This scaling is potentially useful for other electrokinetic flow problems with self-sharpening interfaces.

  4. Observer-based output feedback control of networked control systems with non-uniform sampling and time-varying delay

    Science.gov (United States)

    Meng, Su; Chen, Jie; Sun, Jian

    2017-10-01

    This paper investigates the problem of observer-based output feedback control for networked control systems with non-uniform sampling and time-varying transmission delay. The sampling intervals are assumed to vary within a given interval. The transmission delay belongs to a known interval. A discrete-time model is first established, which contains time-varying delay and norm-bounded uncertainties coming from non-uniform sampling intervals. It is then converted to an interconnection of two subsystems in which the forward channel is delay-free. The scaled small gain theorem is used to derive the stability condition for the closed-loop system. Moreover, the observer-based output feedback controller design method is proposed by utilising a modified cone complementary linearisation algorithm. Finally, numerical examples illustrate the validity and superiority of the proposed method.

  5. Uncertainties in cloud phase and optical thickness retrievals from the Earth Polychromatic Imaging Camera (EPIC).

    Science.gov (United States)

    Meyer, Kerry; Yang, Yuekui; Platnick, Steven

    2016-01-01

    This paper presents an investigation of the expected uncertainties of a single channel cloud optical thickness (COT) retrieval technique, as well as a simple cloud temperature threshold based thermodynamic phase approach, in support of the Deep Space Climate Observatory (DSCOVR) mission. DSCOVR cloud products will be derived from Earth Polychromatic Imaging Camera (EPIC) observations in the ultraviolet and visible spectra. Since EPIC is not equipped with a spectral channel in the shortwave or mid-wave infrared that is sensitive to cloud effective radius (CER), COT will be inferred from a single visible channel with the assumption of appropriate CER values for liquid and ice phase clouds. One month of Aqua MODIS daytime granules from April 2005 is selected for investigating cloud phase sensitivity, and a subset of these granules that has similar EPIC sun-view geometry is selected for investigating COT uncertainties. EPIC COT retrievals are simulated with the same algorithm as the operational MODIS cloud products (MOD06), except using fixed phase-dependent CER values. Uncertainty estimates are derived by comparing the single channel COT retrievals with the baseline bi-spectral MODIS retrievals. Results show that a single channel COT retrieval is feasible for EPIC. For ice clouds, single channel retrieval errors are minimal (< 2%) due to the particle size insensitivity of the assumed ice crystal (i.e., severely roughened aggregate of hexagonal columns) scattering properties at visible wavelengths, while for liquid clouds the error is mostly limited to within 10%, although for thin clouds (COT < 2) the error can be higher. Potential uncertainties in EPIC cloud masking and cloud temperature retrievals are not considered in this study.

  6. Improving adherence to the Epic Beacon ambulatory workflow.

    Science.gov (United States)

    Chackunkal, Ellen; Dhanapal Vogel, Vishnuprabha; Grycki, Meredith; Kostoff, Diana

    2017-06-01

    Computerized physician order entry has been shown to significantly improve chemotherapy safety by reducing the number of prescribing errors. Epic's Beacon Oncology Information System of computerized physician order entry and electronic medication administration was implemented in Henry Ford Health System's ambulatory oncology infusion centers on 9 November 2013. Since that time, compliance to the infusion workflow had not been assessed. The objective of this study was to optimize the current workflow and improve the compliance to this workflow in the ambulatory oncology setting. This study was a retrospective, quasi-experimental study which analyzed the composite workflow compliance rate of patient encounters from 9 to 23 November 2014. Based on this analysis, an intervention was identified and implemented in February 2015 to improve workflow compliance. The primary endpoint was to compare the composite compliance rate to the Beacon workflow before and after a pharmacy-initiated intervention. The intervention, which was education of infusion center staff, was initiated by ambulatory-based, oncology pharmacists and implemented by a multi-disciplinary team of pharmacists and nurses. The composite compliance rate was then reassessed for patient encounters from 2 to 13 March 2015 in order to analyze the effects of the determined intervention on compliance. The initial analysis in November 2014 revealed a composite compliance rate of 38%, and data analysis after the intervention revealed a statistically significant increase in the composite compliance rate to 83% ( p < 0.001). This study supports a pharmacist-initiated educational intervention can improve compliance to an ambulatory, oncology infusion workflow.

  7. Genetic variability of the mTOR pathway and prostate cancer risk in the European Prospective Investigation on Cancer (EPIC.

    Directory of Open Access Journals (Sweden)

    Daniele Campa

    2011-02-01

    Full Text Available The mTOR (mammalian target of rapamycin signal transduction pathway integrates various signals, regulating ribosome biogenesis and protein synthesis as a function of available energy and amino acids, and assuring an appropriate coupling of cellular proliferation with increases in cell size. In addition, recent evidence has pointed to an interplay between the mTOR and p53 pathways. We investigated the genetic variability of 67 key genes in the mTOR pathway and in genes of the p53 pathway which interact with mTOR. We tested the association of 1,084 tagging SNPs with prostate cancer risk in a study of 815 prostate cancer cases and 1,266 controls nested within the European Prospective Investigation into Cancer and Nutrition (EPIC. We chose the SNPs (n = 11 with the strongest association with risk (p<0.01 and sought to replicate their association in an additional series of 838 prostate cancer cases and 943 controls from EPIC. In the joint analysis of first and second phase two SNPs of the PRKCI gene showed an association with risk of prostate cancer (OR(allele = 0.85, 95% CI 0.78-0.94, p = 1.3 x 10⁻³ for rs546950 and OR(allele = 0.84, 95% CI 0.76-0.93, p = 5.6 x 10⁻⁴ for rs4955720. We confirmed this in a meta-analysis using as replication set the data from the second phase of our study jointly with the first phase of the Cancer Genetic Markers of Susceptibility (CGEMS project. In conclusion, we found an association with prostate cancer risk for two SNPs belonging to PRKCI, a gene which is frequently overexpressed in various neoplasms, including prostate cancer.

  8. DSCOVR/EPIC observations of SO2 reveal dynamics of young volcanic eruption clouds

    Science.gov (United States)

    Carn, S. A.; Krotkov, N. A.; Taylor, S.; Fisher, B. L.; Li, C.; Bhartia, P. K.; Prata, F. J.

    2017-12-01

    Volcanic emissions of sulfur dioxide (SO2) and ash have been measured by ultraviolet (UV) and infrared (IR) sensors on US and European polar-orbiting satellites since the late 1970s. Although successful, the main limitation of these observations from low Earth orbit (LEO) is poor temporal resolution (once per day at low latitudes). Furthermore, most currently operational geostationary satellites cannot detect SO2, a key tracer of volcanic plumes, limiting our ability to elucidate processes in fresh, rapidly evolving volcanic eruption clouds. In 2015, the launch of the Earth Polychromatic Imaging Camera (EPIC) aboard the Deep Space Climate Observatory (DSCOVR) provided the first opportunity to observe volcanic clouds from the L1 Lagrange point. EPIC is a 10-band spectroradiometer spanning UV to near-IR wavelengths with two UV channels sensitive to SO2, and a ground resolution of 25 km. The unique L1 vantage point provides continuous observations of the sunlit Earth disk, from sunrise to sunset, offering multiple daily observations of volcanic SO2 and ash clouds in the EPIC field of view. When coupled with complementary retrievals from polar-orbiting UV and IR sensors such as the Ozone Monitoring Instrument (OMI), the Ozone Mapping and Profiler Suite (OMPS), and the Atmospheric Infrared Sounder (AIRS), we demonstrate how the increased observation frequency afforded by DSCOVR/EPIC permits more timely volcanic eruption detection and novel analyses of the temporal evolution of volcanic clouds. Although EPIC has detected several mid- to high-latitude volcanic eruptions since launch, we focus on recent eruptions of Bogoslof volcano (Aleutian Islands, AK, USA). A series of EPIC exposures from May 28-29, 2017, uniquely captures the evolution of SO2 mass in a young Bogoslof eruption cloud, showing separation of SO2- and ice-rich regions of the cloud. We show how analyses of these sequences of EPIC SO2 data can elucidate poorly understood processes in transient eruption

  9. Report on the NAT-9 quality control exercise on uranium isotopes in two soil samples

    International Nuclear Information System (INIS)

    Bleise, Andreas

    2001-04-01

    The International Atomic Energy Agency (IAEA) section of Nutritional and Health related Environmental Studies (NAHRES) organized a quality control study for laboratories analysing samples from the UNEP field mission to Kosovo. Quality control was the major responsibility of the IAEA in the UN field assessment team. The NAT-9 quality control study consists of two soil materials from the IAEA Laboratories in Seibersdorf. The scope of this exercise was to determine the content of the uranium isotopes U-234, U-235 and U-238. The IAEA did not provide specific instructions, the participants were encouraged to apply their established analytical procedures to the samples. Five laboratories were invited to participate, four laboratories submitted results. For each soil sample 10 laboratory mean values were reported, using ICP-MS (3 laboratories) and α-spectrometry (1 laboratory). The participating laboratories were capable to distinguish the different uranium isotopes. All laboratories obtained the natural uranium ratio between U-235 and U-238. However, the results highlight a particular analytical weak spot. Although the methods of measuring the analytical signals are highly dependable, the sample preparation steps, in particular the sample dissolution procedure, appears to be lacking total quality control and has contributed to the deviations from the reported target values. One laboratory has documented evidence that extensive and well-controlled digestion methods can yield measurement results close to the target values. (author)

  10. Practical iterative learning control with frequency domain design and sampled data implementation

    CERN Document Server

    Wang, Danwei; Zhang, Bin

    2014-01-01

    This book is on the iterative learning control (ILC) with focus on the design and implementation. We approach the ILC design based on the frequency domain analysis and address the ILC implementation based on the sampled data methods. This is the first book of ILC from frequency domain and sampled data methodologies. The frequency domain design methods offer ILC users insights to the convergence performance which is of practical benefits. This book presents a comprehensive framework with various methodologies to ensure the learnable bandwidth in the ILC system to be set with a balance between learning performance and learning stability. The sampled data implementation ensures effective execution of ILC in practical dynamic systems. The presented sampled data ILC methods also ensure the balance of performance and stability of learning process. Furthermore, the presented theories and methodologies are tested with an ILC controlled robotic system. The experimental results show that the machines can work in much h...

  11. Preparation of quality control samples in radioimmunoassay for thyroid stimulating hormone (TSH)

    International Nuclear Information System (INIS)

    Ali, O.M.

    2006-03-01

    To days, the radioimmunoassay is becomes the best technique to analysis different concentrations of substance, especially in medical and research laboratories. Although the specificity of RIA techniques, the quality controls must takes place to give good results as possible. In this dissertation i prepared quality control samples of thyroid stimulating hormone (TSH), to use it in RIA techniques and to control the reliability results of those laboratories which used these methods. We used China production kits of RIA method to determine the level of hormone (low-normal-high) concentration. Statistical parameters were used to drown the control chart of the mean to these data.(Author)

  12. Highly simplified lateral flow-based nucleic acid sample preparation and passive fluid flow control

    Science.gov (United States)

    Cary, Robert E.

    2015-12-08

    Highly simplified lateral flow chromatographic nucleic acid sample preparation methods, devices, and integrated systems are provided for the efficient concentration of trace samples and the removal of nucleic acid amplification inhibitors. Methods for capturing and reducing inhibitors of nucleic acid amplification reactions, such as humic acid, using polyvinylpyrrolidone treated elements of the lateral flow device are also provided. Further provided are passive fluid control methods and systems for use in lateral flow assays.

  13. Highly simplified lateral flow-based nucleic acid sample preparation and passive fluid flow control

    Energy Technology Data Exchange (ETDEWEB)

    Cary, Robert B.

    2018-04-17

    Highly simplified lateral flow chromatographic nucleic acid sample preparation methods, devices, and integrated systems are provided for the efficient concentration of trace samples and the removal of nucleic acid amplification inhibitors. Methods for capturing and reducing inhibitors of nucleic acid amplification reactions, such as humic acid, using polyvinylpyrrolidone treated elements of the lateral flow device are also provided. Further provided are passive fluid control methods and systems for use in lateral flow assays.

  14. Sampling technologies and air pollution control devices for gaseous and particulate arsenic: a review

    International Nuclear Information System (INIS)

    Helsen, Lieve

    2005-01-01

    Direct measurement of arsenic release requires a good sampling and analysis procedure in order to capture and detect the total amount of metals emitted. The literature is extensively reviewed in order to evaluate the efficiency of full field-scale and laboratory scale techniques for capturing particulate and gaseous emissions of arsenic from the thermo-chemical treatment of different sources of arsenic. Furthermore, trace arsenic concentrations in ambient air, national standard sampling methods and arsenic analysis methods are considered. Besides sampling techniques, the use of sorbents is also reviewed with respect to both approaches (1) to prevent the metals from exiting with the flue gas and (2) to react or combine with the metals in order to be collected in air pollution control systems. The most important conclusion is that submicron arsenic fumes are difficult to control in conventional air pollution control devices. Complete capture of the arsenic species requires a combination of particle control and vapour control devices. - Submicron arsenic fumes are difficult to control in conventional air pollution control devices

  15. Iterative learning control with sampled-data feedback for robot manipulators

    Directory of Open Access Journals (Sweden)

    Delchev Kamen

    2014-09-01

    Full Text Available This paper deals with the improvement of the stability of sampled-data (SD feedback control for nonlinear multiple-input multiple-output time varying systems, such as robotic manipulators, by incorporating an off-line model based nonlinear iterative learning controller. The proposed scheme of nonlinear iterative learning control (NILC with SD feedback is applicable to a large class of robots because the sampled-data feedback is required for model based feedback controllers, especially for robotic manipulators with complicated dynamics (6 or 7 DOF, or more, while the feedforward control from the off-line iterative learning controller should be assumed as a continuous one. The robustness and convergence of the proposed NILC law with SD feedback is proven, and the derived sufficient condition for convergence is the same as the condition for a NILC with a continuous feedback control input. With respect to the presented NILC algorithm applied to a virtual PUMA 560 robot, simulation results are presented in order to verify convergence and applicability of the proposed learning controller with SD feedback controller attached

  16. An advanced computer-controlled automatic alpha-beta air sample counter

    International Nuclear Information System (INIS)

    Howell, W.P.; Bruinekool, D.J.; Stapleton, E.E.

    1984-01-01

    An improved computer-controlled automatic alpha-beta air sample counter was developed, based upon an earlier automatic air sample counter design. The system consists of an automatic sample changer, an electronic counting system utilizing a large silicon diode detector, a small desk-type microcomputer, a high-speed matrix printer and the necessary data interfaces. The system is operated by commands from the keyboard and programs stored on magnetic tape cassettes. The programs provide for background counting, Chi 2 test, radon subtraction and sample counting for sample periods of one day to one week. Output data are printed by the matrix printer on standard multifold paper. The data output includes gross beta, gross alpha and plutonium results. Data are automatically corrected for background, counter efficiency, and in the gross alpha and plutonium channels, for the presence of radon

  17. [Sampling in quality control of medicinal materials-A case of Epimedium].

    Science.gov (United States)

    Wang, Chuanyi; Cao, Jinyi; Liang, Yun; Huang, Wenhua; Guo, Baolin

    2009-04-01

    To investigate the effect of the different individual number of sampling on the assay results of the medicinal materials. Epimedium pubescens and E. brevicornu were used as samples. The 6 sampling levels were formulated as 1 individual, 5, 10, 20, 30, 50 individuals mix, each level with 3 parallels and 1 individual level5 parallels. The contents of epimedin C and icariin, and the peak areas of epimedin A, epimedin B, rhamnosyl icarisid II and icarisid II in all samples were analyzed by HPLC. The variation degree varied with species and chemical constituents, but the RSD and the deviation from the true value decreased with the increase of individual number on the same chemical constituent. The sampling number should be more than 10 individuals in quality control of Epimedium, and 50 or more individuals would be better for representing the quality of medicinal materials.

  18. Automated facility for analysis of soil samples by neutron activation, counting, and data control

    International Nuclear Information System (INIS)

    Voegele, A.L.; Jesse, R.H.; Russell, W.L.; Baker, J.

    1978-01-01

    An automated facility remotely and automatically analyzes soil, water, and sediment samples for uranium. The samples travel through pneumatic tubes and switches to be first irradiated by neutrons and then counted for resulting neutron and gamma emission. Samples are loaded into special carriers, or rabbits, which are then automatically loaded into the pneumatic transfer system. The sample carriers have been previously coded with an identification number, which can be automatically read in the system. This number is used for correlating and filing data about the samples. The transfer system, counters, and identification system are controlled by a network of microprocessors. A master microprocessor initiates routines in other microprocessors assigned to specific tasks. The software in the microprocessors is unique for this type of application and lends flexibility to the system

  19. Advanced computer-controlled automatic alpha-beta air sample counter

    International Nuclear Information System (INIS)

    Howell, W.P.; Bruinekool, D.J.; Stapleton, E.E.

    1983-01-01

    An improved computer controlled automatic alpha-beta air sample counter was developed, based upon an earlier automatic air sample counter design. The system consists of an automatic sample changer, an electronic counting system utilizing a large silicon diode detector, a small desk-type microcomputer, a high speed matrix printer, and the necessary data interfaces. The system is operated by commands from the keyboard and programs stored on magnetic tape cassettes. The programs provide for background counting, Chi 2 test, radon subtraction, and sample counting for sample periods of one day to one week. Output data are printed by the matrix printer on standard multifold paper. The data output includes gross beta, gross alpha, and plutonium results. Data are automatically corrected for background, counter efficiency, and in the gross alpha and plutonium channels, for the presence of radon

  20. Maximum likelihood estimation for Cox's regression model under nested case-control sampling

    DEFF Research Database (Denmark)

    Scheike, Thomas Harder; Juul, Anders

    2004-01-01

    -like growth factor I was associated with ischemic heart disease. The study was based on a population of 3784 Danes and 231 cases of ischemic heart disease where controls were matched on age and gender. We illustrate the use of the MLE for these data and show how the maximum likelihood framework can be used......Nested case-control sampling is designed to reduce the costs of large cohort studies. It is important to estimate the parameters of interest as efficiently as possible. We present a new maximum likelihood estimator (MLE) for nested case-control sampling in the context of Cox's proportional hazards...... model. The MLE is computed by the EM-algorithm, which is easy to implement in the proportional hazards setting. Standard errors are estimated by a numerical profile likelihood approach based on EM aided differentiation. The work was motivated by a nested case-control study that hypothesized that insulin...

  1. Sampled-Data Control of Spacecraft Rendezvous with Discontinuous Lyapunov Approach

    Directory of Open Access Journals (Sweden)

    Zhuoshi Li

    2013-01-01

    Full Text Available This paper investigates the sampled-data stabilization problem of spacecraft relative positional holding with improved Lyapunov function approach. The classical Clohessy-Wiltshire equation is adopted to describe the relative dynamic model. The relative position holding problem is converted into an output tracking control problem using sampling signals. A time-dependent discontinuous Lyapunov functionals approach is developed, which will lead to essentially less conservative results for the stability analysis and controller design of the corresponding closed-loop system. Sufficient conditions for the exponential stability analysis and the existence of the proposed controller are provided, respectively. Finally, a simulation result is established to illustrate the effectiveness of the proposed control scheme.

  2. A Discrete-Time Chattering Free Sliding Mode Control with Multirate Sampling Method for Flight Simulator

    Directory of Open Access Journals (Sweden)

    Yunjie Wu

    2013-01-01

    Full Text Available In order to improve the tracking accuracy of flight simulator and expend its frequency response, a multirate-sampling-method-based discrete-time chattering free sliding mode control is developed and imported into the systems. By constructing the multirate sampling sliding mode controller, the flight simulator can perfectly track a given reference signal with an arbitrarily small dynamic tracking error, and the problems caused by a contradiction of reference signal period and control period in traditional design method can be eliminated. It is proved by theoretical analysis that the extremely high dynamic tracking precision can be obtained. Meanwhile, the robustness is guaranteed by sliding mode control even though there are modeling mismatch, external disturbances and measure noise. The validity of the proposed method is confirmed by experiments on flight simulator.

  3. Quality control on the accuracy of the total Beta activity index in different sample matrices water

    International Nuclear Information System (INIS)

    Pujol, L.; Pablo, M. A. de; Payeras, J.

    2013-01-01

    The standard ISO/IEC 17025:2005 of general requirements for the technical competence of testing and calibration laboratories, provides that a laboratory shall have quality control procedures for monitoring the validity of tests and calibrations ago. In this paper, the experience of Isotopic Applications Laboratory (CEDEX) in controlling the accuracy rate of total beta activity in samples of drinking water, inland waters and marine waters is presented. (Author)

  4. Advanced Data Acquisition System Implementation for the ITER Neutron Diagnostic Use Case Using EPICS and FlexRIO Technology on a PXIe Platform

    Science.gov (United States)

    Sanz, D.; Ruiz, M.; Castro, R.; Vega, J.; Afif, M.; Monroe, M.; Simrock, S.; Debelle, T.; Marawar, R.; Glass, B.

    2016-04-01

    To aid in assessing the functional performance of ITER, Fission Chambers (FC) based on the neutron diagnostic use case deliver timestamped measurements of neutron source strength and fusion power. To demonstrate the Plant System Instrumentation & Control (I&C) required for such a system, ITER Organization (IO) has developed a neutron diagnostics use case that fully complies with guidelines presented in the Plant Control Design Handbook (PCDH). The implementation presented in this paper has been developed on the PXI Express (PXIe) platform using products from the ITER catalog of standard I&C hardware for fast controllers. Using FlexRIO technology, detector signals are acquired at 125 MS/s, while filtering, decimation, and three methods of neutron counting are performed in real-time via the onboard Field Programmable Gate Array (FPGA). Measurement results are reported every 1 ms through Experimental Physics and Industrial Control System (EPICS) Channel Access (CA), with real-time timestamps derived from the ITER Timing Communication Network (TCN) based on IEEE 1588-2008. Furthermore, in accordance with ITER specifications for CODAC Core System (CCS) application development, the software responsible for the management, configuration, and monitoring of system devices has been developed in compliance with a new EPICS module called Nominal Device Support (NDS) and RIO/FlexRIO design methodology.

  5. Improving ambulatory saliva-sampling compliance in pregnant women: a randomized controlled study.

    Directory of Open Access Journals (Sweden)

    Julian Moeller

    Full Text Available OBJECTIVE: Noncompliance with scheduled ambulatory saliva sampling is common and has been associated with biased cortisol estimates in nonpregnant subjects. This study is the first to investigate in pregnant women strategies to improve ambulatory saliva-sampling compliance, and the association between sampling noncompliance and saliva cortisol estimates. METHODS: We instructed 64 pregnant women to collect eight scheduled saliva samples on two consecutive days each. Objective compliance with scheduled sampling times was assessed with a Medication Event Monitoring System and self-reported compliance with a paper-and-pencil diary. In a randomized controlled study, we estimated whether a disclosure intervention (informing women about objective compliance monitoring and a reminder intervention (use of acoustical reminders improved compliance. A mixed model analysis was used to estimate associations between women's objective compliance and their diurnal cortisol profiles, and between deviation from scheduled sampling and the cortisol concentration measured in the related sample. RESULTS: Self-reported compliance with a saliva-sampling protocol was 91%, and objective compliance was 70%. The disclosure intervention was associated with improved objective compliance (informed: 81%, noninformed: 60%, F(1,60  = 17.64, p<0.001, but not the reminder intervention (reminders: 68%, without reminders: 72%, F(1,60 = 0.78, p = 0.379. Furthermore, a woman's increased objective compliance was associated with a higher diurnal cortisol profile, F(2,64  = 8.22, p<0.001. Altered cortisol levels were observed in less objective compliant samples, F(1,705  = 7.38, p = 0.007, with delayed sampling associated with lower cortisol levels. CONCLUSIONS: The results suggest that in pregnant women, objective noncompliance with scheduled ambulatory saliva sampling is common and is associated with biased cortisol estimates. To improve sampling compliance, results suggest

  6. Plasma elaidic acid level as biomarker of industrial trans fatty acids and risk of weight change: report from the EPIC study.

    Science.gov (United States)

    Chajès, Véronique; Biessy, Carine; Ferrari, Pietro; Romieu, Isabelle; Freisling, Heinz; Huybrechts, Inge; Scalbert, Augustin; Bueno de Mesquita, Bas; Romaguera, Dora; Gunter, Marc J; Vineis, Paolo; Hansen, Camilla Plambeck; Jakobsen, Marianne Uhre; Clavel-Chapelon, Françoise; Fagherazzi, Guy; Boutron-Ruault, Marie-Christine; Katzke, Verana; Neamat-Allah, Jasmine; Boeing, Heiner; Bachlechner, Ursula; Trichopoulou, Antonia; Naska, Androniki; Orfanos, Philippos; Pala, Valeria; Masala, Giovanna; Mattiello, Amalia; Skeie, Guri; Weiderpass, Elisabete; Agudo, Antonio; Huerta, Jose Maria; Ardanaz, Eva; Sánchez, Maria Jose; Dorronsoro, Miren; Quirós, Jose Ramon; Johansson, Ingegerd; Winkvist, Anna; Sonested, Emily; Key, Tim; Khaw, Kay-Tee; Wareham, Nicolas J; Peeters, Petra H M; Slimani, Nadia

    2015-01-01

    Few epidemiological studies have examined the association between dietary trans fatty acids and weight gain, and the evidence remains inconsistent. The main objective of the study was to investigate the prospective association between biomarker of industrial trans fatty acids and change in weight within the large study European Prospective Investigation into Cancer and Nutrition (EPIC) cohort. Baseline plasma fatty acid concentrations were determined in a representative EPIC sample from the 23 participating EPIC centers. A total of 1,945 individuals were followed for a median of 4.9 years to monitor weight change. The association between elaidic acid level and percent change of weight was investigated using a multinomial logistic regression model, adjusted by length of follow-up, age, energy, alcohol, smoking status, physical activity, and region. In women, doubling elaidic acid was associated with a decreased risk of weight loss (odds ratio (OR) = 0.69, 95% confidence interval (CI) = 0.55-0.88, p = 0.002) and a trend was observed with an increased risk of weight gain during the 5-year follow-up (OR = 1.23, 95% CI = 0.97-1.56, p = 0.082) (p-trendacid level and risk of weight loss (OR = 0.82, 95% CI = 0.66-1.01, p = 0.062) while no significant association was found with risk of weight gain during the 5-year follow-up (OR = 1.08, 95% CI = 0.88-1.33, p = 0.454). No association was found for saturated and cis-monounsaturated fatty acids. These data suggest that a high intake of industrial trans fatty acids may decrease the risk of weight loss, particularly in women. Prevention of obesity should consider limiting the consumption of highly processed foods, the main source of industrially-produced trans fatty acids.

  7. External quality control in ground-water sampling and analysis at the Hanford Site

    International Nuclear Information System (INIS)

    Hall, S.H.; Juracich, S.P.

    1991-11-01

    At the US Department of Energy's Hanford Site, external Quality Control (QC) for ground-water monitoring is extensive and has included routine submittal of intra- and interlaboratory duplicate samples, blind samples, and several kinds of blank samples. Examination of the resulting QC data for nine of the constituents found in ground water at the Hanford Site shows that the quality of analysis has generally been within the expectations of precision and accuracy that have been established by the US Environmental Protection Agency (EPA). The constituents subjected to review were nitrate, chromium, sodium, fluoride, carbon tetrachloride, tritium, ammonium, trichloroethylene, and cyanide. Of these, the fluoride measurements were notable exceptions and were poor by EPA standards. The review has shown that interlaboratory analysis of duplicate samples yields the most useful QC data for evaluating laboratory performance in determining commonly encountered constituents. For rarely encountered constituents, interlaboratory comparisons may be augmented with blind samples (synthetic samples of known composition). Intralaboratory comparisons, blanks, and spikes should be generally restricted to studies of suspected or known sample contamination and to studies of the adequacy of sampling and analytical procedures

  8. Politics in poetry: epic poetry as a critique of Dutch culture

    Directory of Open Access Journals (Sweden)

    O.M. Heynders

    2010-07-01

    Full Text Available This article describes a Dutch volume of epic poetry, using a disciplinary strategy (concepts and devices from narrative studies and a cultural analytical and rhetorical approach. The volume “Roeshoofd hemelt” by Joost Zwagerman (2005 is a political poetic text that raises fundamental questions on issues of mental illness and on consumerism in contemporary Dutch society.

  9. Diversity of dietary patterns observed in the European Prospective Investigation into Cancer and Nutrition (EPIC) project

    NARCIS (Netherlands)

    Slimani, N.; Fahey, M.; Welch, A.A.; Wirfalt, E.; Stripp, C.; Bergstrom, E.; Linseisen, J.; Schulze, M.B.; Bamia, C.; Chloptsios, Y.; Veglia, F.; Panico, S.; Bueno de Mesquita, B.; Ocké, M.C.; Brustadt, M.; Lund, E.; Gonzalez, C.A.; Barcos, A.; Berglund, G.; Winkvist, A.; Mulligan, A.; Appleby, P.; Overvad, K.; Tjonneland, A.; Clavel-Chapelon, F.; Kesse, E.; Ferrari, P.; Staveren, van W.A.; Riboli, E.

    2002-01-01

    Objective: To describe the diversity in dietary patterns existing across centres/regions participating in the European Prospective Investigation into Cancer and Nutrition (EPIC). Design and setting: Single 24-hour dietary recall measurements were obtained by means of standardised face-to-face

  10. The True Lion King of Africa: The Epic History of Sundiata, King of Old Mali.

    Science.gov (United States)

    Paterno, Domenica R.

    David Wisniewski's 1992 picture book version of the African epic of "Sundiata, Lion King of Mali" and the actual historical account of the 13th century Lion King, Sundiata, are both badly served by Disney's "The Lion King." Disney has been praised for using African animals as story characters; for using the African landscape as…

  11. The Epic Poem "Raol de Cambrai" and Student Analysis of the French Feudal Aristocracy.

    Science.gov (United States)

    Madison, Kenneth G.

    1980-01-01

    Suggests how college history teachers can help students understand the French aristocracy and its role in medieval society by using a twelfth century epic. "Raol de Cambrai" gives students a sense that the poem's action could have happened to real people. A content analysis of the poem's action and characters is included. (DB)

  12. Constraining the Origin of Phobos with the Elpasolite Planetary Ice and Composition Spectrometer (EPICS) - Simulated Performance

    Science.gov (United States)

    Nowicki, S. F.; Mesick, K.; Coupland, D. D. S.; Dallmann, N. A.; Feldman, W. C.; Stonehill, L. C.; Hardgrove, C.; Dibb, S.; Gabriel, T. S. J.; West, S.

    2017-12-01

    Elpasolites are a promising new family of inorganic scintillators that can detect both gamma rays and neutrons within a single detector volume, reducing the instrument size, weight, and power (SWaP), all of which are critical for planetary science missions. The ability to distinguish between neutron and gamma events is done through pulse shape discrimination (PSD). The Elpasolite Planetary Ice and Composition Spectrometer (EPICS) utilizes elpasolites in a next-generation, highly capable, low-SWaP gamma-ray and neutron spectrometer. We present simulated capabilities of EPICS sensitivities to neutron and gamma-rays, and demonstrate how EPICS can constrain the origin of Phobos between the following three main hypotheses: 1) accretion after a giant impact with Mars, 2) co-accretion with Mars, and 3) capture of an external body. The MCNP6 code was used to calculate the neutron and gamma-ray flux that escape the surface of Phobos, and GEANT4 to model the response of the EPICS instrument on orbit around Phobos.

  13. EPIC 219217635: A Doubly Eclipsing Quadruple System Containing an Evolved Binary

    DEFF Research Database (Denmark)

    Borkovits, T.; Albrecht, S.; Rappaport, S.

    2018-01-01

    We have discovered a doubly eclipsing, bound, quadruple star system in the field of K2 Campaign 7. EPIC 219217635 is a stellar image with Kp = 12.7 that contains an eclipsing binary (‘EB’) with PA = 3.59470 d and a second EB with PB = 0.61825 d. We have obtained followup radial-velocity (‘RV’) sp...

  14. POPULARIZING EPIC NARRATIVE IN GEORGE R.R. MARTIN'S A GAME OF THRONES

    Directory of Open Access Journals (Sweden)

    Ida Rochani Adi

    2012-11-01

    Full Text Available This research is intended to show the sustainability of epic in latest years of human history through the most phenomenal fantasy in American literature, A Game of Thrones. Along with the capability of human beings in thinking dearly and sensibly, it is commonsensical that people tend to free themselves from irrationality. The reality shows, however, that the existence of epic fantasy still has power in appealing audiences or readers. This is the case with A Game of Thrones written by George RR Martin who was given the award of One of The Most Influential People in 2011 by Time magazine. This qualitative march, using genre approach, finds out that in order to be compatible with today's society, an epic seen in A Game of Thrones, which is commonly known as a story centering on the legendary hero and his heroic deed in oral folk tradition, keeps its power as an epic fantasy narrative through certain archetypes and formulas. Through genre analysis using semiotic approach, the research brings about conclusions that the elements of high fantasy, elements built through rational representation, and a smart combination of convention and invention brings about its popularity. It is also concluded that there is a close relationship between the myth and the mode of people living even in the most modern context.

  15. Mediterranean Style Diet and 12-Year Incidence of Cardiovascular Diseases: The Epic-NL Cohort Stusy

    NARCIS (Netherlands)

    Hoevenaar-Blom, M.P.; Nooyens, A.J.C.; Kromhout, D.; Spijkerman, A.M.W.; Beulens, W.J.; Schouw, van der Y.T.; Bueno-de-Mesquita4, B.; Verschuren, W.M.M.

    2012-01-01

    Background: A recent meta-analysis showed that a Mediterranean style diet may protect against cardiovascular diseases (CVD). Studies on disease-specific associations are limited. We evaluated the Mediterranean Diet Score (MDS) in relation to incidence of total and specific CVDs. Methods: The EPIC-NL

  16. Poetics of the Epic and Survivals of the Genre in Swaziland ...

    African Journals Online (AJOL)

    This paper seeks to suggest that the ongoing and robust tradition of bringing together excerpts from legends, praise poems, songs and genealogical recitations during national ceremonies and festivals such as Incwala, vouch for an erstwhile epic culture in Swaziland. International Journal of Humanistic Studies Vol.3 2004: ...

  17. Design of a Clean Room for Quality Control of an Environmental Sampling in KINAC

    International Nuclear Information System (INIS)

    Yoon, Jongho; Ahn, Gil Hoon; Seo, Hana; Han, Kitek; Park, Il Jin

    2014-01-01

    The objective of environmental sampling and analysis for safeguards is to characterize the nuclear materials handled and the activities conducted at the specific locations. The KINAC is responsible for the conclusions drawn from the analytical results provided by the analytical laboratories. To assure the KINAC of the continuity of the quality of the analytical results provided by the laboratories, the KINAC will implement a quality control(QC) programme. One of the QC programme is to prepare QC samples. The establishment of a clean room is needed to handle QC samples due to stringent control of contamination. The KINAC designed a clean facility with cleanliness of ISO Class 6, the Clean Room for Estimation and Assay of trace Nuclear materials(CREAN) to meet conflicting requirements of a clean room and for handling of nuclear materials according to Korean laws. The clean room will be expected to acquire of a radiation safety license under these conditions in this year and continue to improve it. The construction of the CREAN facility will be completed by the middle of 2015. In terms of QC programme, the establishment of a clean room is essential and will be not only very helpful for setting of quality control system for the national environmental sampling programme but also be applied for the environmental sample analysis techniques to the nuclear forensics

  18. Networked control systems with communication constraints :tradeoffs between sampling intervals, delays and performance

    NARCIS (Netherlands)

    Heemels, W.P.M.H.; Teel, A.R.; Wouw, van de N.; Nesic, D.

    2010-01-01

    There are many communication imperfections in networked control systems (NCS) such as varying transmission delays, varying sampling/transmission intervals, packet loss, communication constraints and quantization effects. Most of the available literature on NCS focuses on only some of these aspects,

  19. Controlled power delivery for super-resolution imaging of biological samples using digital micromirror device

    Science.gov (United States)

    Valiya Peedikakkal, Liyana; Cadby, Ashley

    2017-02-01

    Localization based super resolution images of a biological sample is generally achieved by using high power laser illumination with long exposure time which unfortunately increases photo-toxicity of a sample, making super resolution microscopy, in general, incompatible with live cell imaging. Furthermore, the limitation of photobleaching reduces the ability to acquire time lapse images of live biological cells using fluorescence microscopy. Digital Light Processing (DLP) technology can deliver light at grey scale levels by flickering digital micromirrors at around 290 Hz enabling highly controlled power delivery to samples. In this work, Digital Micromirror Device (DMD) is implemented in an inverse Schiefspiegler telescope setup to control the power and pattern of illumination for super resolution microscopy. We can achieve spatial and temporal patterning of illumination by controlling the DMD pixel by pixel. The DMD allows us to control the power and spatial extent of the laser illumination. We have used this to show that we can reduce the power delivered to the sample to allow for longer time imaging in one area while achieving sub-diffraction STORM imaging in another using higher power densities.

  20. Glycemic Control in a Clinic-Based Sample of Diabetics in M'Bour Senegal

    Science.gov (United States)

    BeLue, Rhonda; Ndiaye, Khadidiatou; NDao, Fatou; Ba, Fatou Niass Niang; Diaw, Mor

    2016-01-01

    Background: Sub-Saharan Africa (SSA) including Senegal is faced with a significant and increasing burden of type 2 diabetes. However, little information is available about diabetes management among Senegalese diabetics. Purpose: The current study aims to describe the level of glycemic control among a convenience sample of diabetics who receive…

  1. Quality control of measurements made on fixed-area sample plots

    Science.gov (United States)

    Ola Lindgren

    2000-01-01

    The paper describes results from a large program for quality control of forest measurements. The performance of 87 surveyors was evaluated. Tree heights were usually measured well, whereas the counting of tree-rings on increment cores was a source of considerable bias for many surveyors. During tree count on sample plots, many surveyors had a tendency to forget trees,...

  2. PCR assay with host specific internal control forStaphylococcus aureus from bovine milk samples

    Directory of Open Access Journals (Sweden)

    Zafer Cantekin

    2015-03-01

    Full Text Available Staphylococcus aureus is considered as one of the most important and common pathogens of bovine mastitis. Polymerase Chain Reaction is frequently proposed in the diagnosis of S. aureus directly from milk samples instead of classical culture. However, false-negative results may occur in the polymerase chain reaction analysis performed directly from clinical material. For the purpose of disclosing the false negative results, the use of internal amplification controls can be beneficial. Therefore, in this study a new polymerase chain reaction technique with host specific internal amplification control was developed by optimizing S. aureus-specific primers in combination with bovine specific primers. The effectiveness of the developed technique in this study was attempted in milk samples from bovine subclinical mastitis. This technique has the potential to detect S. aureus from bovine milk samples or dairy products.

  3. Implementation of an Enhanced Measurement Control Program for handling nuclear safety samples at WSRC

    International Nuclear Information System (INIS)

    Boler-Melton, C.; Holland, M.K.

    1991-01-01

    In the separation and purification of nuclear material, nuclear criticality safety (NCS) is of primary concern. The primary nuclear criticality safety controls utilized by the Savannah River Site (SRS) Separations Facilities involve administrative and process equipment controls. Additional assurance of NCS is obtained by identifying key process hold points where sampling is used to independently verify the effectiveness of production control. Nuclear safety measurements of samples from these key process locations provide a high degree of assurance that processing conditions are within administrative and procedural nuclear safety controls. An enhanced procedure management system aimed at making improvements in the quality, safety, and conduct of operation was implemented for Nuclear Safety Sample (NSS) receipt, analysis, and reporting. All procedures with nuclear safety implications were reviewed for accuracy and adequate detail to perform the analytical measurements safely, efficiently, and with the utmost quality. Laboratory personnel worked in a ''Deliberate Operating'' mode (a systematic process requiring continuous expert oversight during all phases of training, testing, and implementation) to initiate the upgrades. Thus, the effort to revise and review nuclear safety sample procedures involved a team comprised of a supervisor, chemist, and two technicians for each procedure. Each NSS procedure was upgraded to a ''Use Every Time'' (UET) procedure with sign-off steps to ensure compliance with each step for every nuclear safety sample analyzed. The upgrade program met and exceeded both the long and short term customer needs by improving measurement reliability, providing objective evidence of rigid adherence to program principles and requirements, and enhancing the system for independent verification of representative sampling from designated NCS points

  4. 3D virtual world remote laboratory to assist in designing advanced user defined DAQ systems based on FlexRIO and EPICS

    Energy Technology Data Exchange (ETDEWEB)

    Carpeño, A., E-mail: antonio.cruiz@upm.es [Universidad Politécnica de Madrid UPM, Madrid (Spain); Contreras, D.; López, S.; Ruiz, M.; Sanz, D.; Arcas, G. de; Esquembri, S. [Universidad Politécnica de Madrid UPM, Madrid (Spain); Vega, J.; Castro, R. [Laboratorio Nacional de Fusión CIEMAT, Madrid (Spain)

    2016-11-15

    Highlights: • Assist in the design of FPGA-based data acquisition systems using EPICS and FlexRIO. • Virtual Reality technologies are highly effective at creating rich training scenarios. • Virtual actions simulate the behavior of a real system to enhance the training process. • Virtual actions can make real changes remotely in the physical ITER’s Fast Controller. - Abstract: iRIO-3DLab is a platform devised to assist developers in the design and implementation of intelligent and reconfigurable FPGA-based data acquisition systems using EPICS and FlexRIO technologies. Although these architectures are very powerful in defining the behavior of DAQ systems, this advantage comes at the price of greater difficulty in understanding how the system works, and how it should be configured and built according to the hardware available and the processing demanded by the requirements of the diagnostics. In this regard, Virtual Reality technologies are highly effective at creating rich training scenarios due to their ability to provide immersive training experiences and collaborative environments. The designed remote laboratory is based on a 3D virtual world developed in Opensim, which is accessible through a standard free 3D viewer. Using a client-server architecture, the virtual world connects with a service running in a Linux-based computer executing EPICS. Through their avatars, users interact with virtual replicas of this equipment as they would in real-life situations. Some actions can be used to simulate the behavior of a real system to enhance the training process, while others can be used to make real changes remotely in the physical system.

  5. 3D virtual world remote laboratory to assist in designing advanced user defined DAQ systems based on FlexRIO and EPICS

    International Nuclear Information System (INIS)

    Carpeño, A.; Contreras, D.; López, S.; Ruiz, M.; Sanz, D.; Arcas, G. de; Esquembri, S.; Vega, J.; Castro, R.

    2016-01-01

    Highlights: • Assist in the design of FPGA-based data acquisition systems using EPICS and FlexRIO. • Virtual Reality technologies are highly effective at creating rich training scenarios. • Virtual actions simulate the behavior of a real system to enhance the training process. • Virtual actions can make real changes remotely in the physical ITER’s Fast Controller. - Abstract: iRIO-3DLab is a platform devised to assist developers in the design and implementation of intelligent and reconfigurable FPGA-based data acquisition systems using EPICS and FlexRIO technologies. Although these architectures are very powerful in defining the behavior of DAQ systems, this advantage comes at the price of greater difficulty in understanding how the system works, and how it should be configured and built according to the hardware available and the processing demanded by the requirements of the diagnostics. In this regard, Virtual Reality technologies are highly effective at creating rich training scenarios due to their ability to provide immersive training experiences and collaborative environments. The designed remote laboratory is based on a 3D virtual world developed in Opensim, which is accessible through a standard free 3D viewer. Using a client-server architecture, the virtual world connects with a service running in a Linux-based computer executing EPICS. Through their avatars, users interact with virtual replicas of this equipment as they would in real-life situations. Some actions can be used to simulate the behavior of a real system to enhance the training process, while others can be used to make real changes remotely in the physical system.

  6. The Prevalence and Typologies of Controlling Behaviors in a General Population Sample.

    Science.gov (United States)

    Walker, Kate; Sleath, Emma; Tramontano, Carlo

    2017-10-01

    The aim of this study was to examine the prevalence and typologies of controlling behaviors within a general population sample. Participants ( N = 427) completed the Revised Controlling Behaviors Scale and the Revised Conflict Tactics Scale. Prevalence of perpetration and victimization of controlling behaviors was relatively high, although the frequency and severity of the behaviors was mainly low level. Five clusters were established based on the use of five types of controlling behaviors: economic, threatening, intimidating, emotional, and isolating. Significant differences were found between the perpetration clusters and (a) minor physical assault, (b) severe physical assault, (c) minor psychological aggression, and (d) severe psychological aggression. Furthermore, significant differences were found between the victimization clusters and (a) physical assault, (b) minor psychological aggression, and (c) severe psychological aggression. It is clear that controlling behaviors are a feature within general population relationships, and further research is required to understand when such behaviors become problematic, and what needs to be done to prevent this from happening.

  7. Using sampled-data feedback control and linear feedback synchronization in a new hyperchaotic system

    International Nuclear Information System (INIS)

    Zhao Junchan; Lu Junan

    2008-01-01

    This paper investigates control and synchronization of a new hyperchaotic system which was proposed by [Chen A, Lu J-A, Lue J, Yu S. Generating hyperchaotic Lue attractor via state feedback control. Physica A 2006;364:103-10]. Firstly, we give different sampled-data feedback control schemes with the variation of system parameter d. Specifically, we only use one controller to drive the system to the origin when d element of (-0.35, 0), and use two controllers if d element of [0, 1.3]. Next, we combine PC method with linear feedback approach to realize synchronization, and derive similar conclusions with varying d. Numerical simulations are also given to validate the proposed approaches

  8. Integration of the HVCM PLC into the PEFP Control System

    International Nuclear Information System (INIS)

    Song, Young Gi; Jang, Ji Ho; Kwon, Hyeok Jung; Cho, Yong Sub

    2011-01-01

    The High Voltage Converter Modulators (HVCM) for the 100-MeV accelerator was installed to drive the 20-MeV linac. There are two klystrons in the 20-MeV linac and one modulator was used to drive two klystrons simultaneously. The HVCM for the 20-MeV linac area in Korea Atomic Energy Research Institute (KAERI) is shown in Fig. 1. We were faced with the necessity of integrating Programmable Logic Controllers (PLCs) for the HVCM into the Proton Engineering Frontier Project (PEFP) control system. At the PEFP, Experimental Physics and Industrial Control System (EPICS) has become the most widely used solution for building control systems for 100MeV proton accelerator. The EPICS as a standard development tool is a distributed architecture that provides several solutions such as independent programming tools for operating system, operator interface tools, and archiving tools. Although EPICS is used directly in our control system, HVCMs were delivered with the Allen-Bradley ControlLogix as a PLC. The industrial PLC has been verified for safety systems. We need to connect an interface from our EPICS control system to AB-PLC using Ethernet/IP (ControlNet over Ethernet) protocol over Ethernet. In this paper, we will present the communication protocol and EPICS IOC installation for the EPICS based PLC control system

  9. Modeling Microbial Processes in EPIC to Estimate Greenhouse Gas Emissions from soils

    Science.gov (United States)

    Schwab, D. E.; Izaurralde, R. C.; McGill, W. B.; Williams, J. R.; Schmid, E.

    2009-12-01

    Emissions of trace gases (CO2, N2O and CH4) to the atmosphere from managed terrestrial ecosystems have been contributing significantly to the warming of Earth. Trace gas production is dominated by biospheric processes. An improved knowledge of the soil-plant-atmosphere interface is of key importance for understanding trace gas dynamics. In soils, microbial metabolism plays a key role in the release or uptake of trace gases. Here we present work on the biophysical and biogeochemical model EPIC (Environmental Policy/Integrated Climate) to extend its capabilities to simulate CO2 and N2O fluxes in managed and unmanaged ecosystems. Emphasis will be given to recently developed, microbially-based, denitrification and nitrification modules. The soil-atmosphere exchange of trace gases can be measured by using various equipments, but often these measurements exhibit extreme space-time variability. We use hourly time steps to account for the variability induced by small changes in environmental conditions. Soils are often studied as macroscopic systems, although their functions are predominantly controlled at a microscopic level; i.e. the level of the microorganisms. We include these processes to the extent that these are known and can be quantitatively described. We represent soil dynamics mathematically with routines for gas diffusion, Michael Menten processes, electron budgeting and other processes such as uptake and transformations. We hypothesize that maximization of energy capture form scarce substrates using energetic favorable reactions drives evolution and that competitive advantage can result by depriving a competitor from a substrate. This Microbe Model changes concepts of production of N-containing trace gases; it unifies understanding of N oxidation and reduction, predicts production and evolution of trace gases and is consistent with observations of anaerobic ammonium oxidation.

  10. Comparing U.S. Army suicide cases to a control sample: initial data and methodological lessons.

    Science.gov (United States)

    Alexander, Cynthia L; Reger, Mark A; Smolenski, Derek J; Fullerton, Nicole R

    2014-10-01

    Identification of risk and protective factors for suicide is a priority for the United States military, especially in light of the recent steady increase in military suicide rates. The Department of Defense Suicide Event Report contains comprehensive data on suicides for active duty military personnel, but no analogous control data is available to permit identification of factors that differentially determine suicide risk. This proof-of-concept study was conducted to determine the feasibility of collecting such control data. The study employed a prospective case-control design in which control cases were randomly selected from a large Army installation at a rate of four control participants for every qualifying Army suicide. Although 111 Army suicides were confirmed during the study period, just 27 control soldiers completed the study. Despite the small control sample, preliminary analyses comparing suicide cases to controls identified several factors more frequently reported for suicide cases, including recent failed intimate relationships, outpatient mental health history, mood disorder diagnosis, substance abuse history, and prior self-injury. No deployment-related risk factors were found. These data are consistent with existing literature and form a foundation for larger control studies. Methodological lessons learned regarding study design and recruitment are discussed to inform future studies. Reprint & Copyright © 2014 Association of Military Surgeons of the U.S.

  11. The lack of selection bias in a snowball sampled case-control study on drug abuse.

    Science.gov (United States)

    Lopes, C S; Rodrigues, L C; Sichieri, R

    1996-12-01

    Friend controls in matched case-control studies can be a potential source of bias based on the assumption that friends are more likely to share exposure factors. This study evaluates the role of selection bias in a case-control study that used the snowball sampling method based on friendship for the selection of cases and controls. The cases selected fro the study were drug abusers located in the community. Exposure was defined by the presence of at least one psychiatric diagnosis. Psychiatric and drug abuse/dependence diagnoses were made according to the Diagnostic and Statistical Manual of Mental Disorders (DSM-III-R) criteria. Cases and controls were matched on sex, age and friendship. The measurement of selection bias was made through the comparison of the proportion of exposed controls selected by exposed cases (p1) with the proportion of exposed controls selected by unexposed cases (p2). If p1 = p2 then, selection bias should not occur. The observed distribution of the 185 matched pairs having at least one psychiatric disorder showed a p1 value of 0.52 and a p2 value of 0.51, indicating no selection bias in this study. Our findings support the idea that the use of friend controls can produce a valid basis for a case-control study.

  12. Heating and thermal control of brazing technique to break contamination path for potential Mars sample return

    Science.gov (United States)

    Bao, Xiaoqi; Badescu, Mircea; Sherrit, Stewart; Bar-Cohen, Yoseph; Campos, Sergio

    2017-04-01

    The potential return of Mars sample material is of great interest to the planetary science community, as it would enable extensive analysis of samples with highly sensitive laboratory instruments. It is important to make sure such a mission concept would not bring any living microbes, which may possibly exist on Mars, back to Earth's environment. In order to ensure the isolation of Mars microbes from Earth's Atmosphere, a brazing sealing and sterilizing technique was proposed to break the Mars-to-Earth contamination path. Effectively, heating the brazing zone in high vacuum space and controlling the sample temperature for integrity are key challenges to the implementation of this technique. The break-thechain procedures for container configurations, which are being considered, were simulated by multi-physics finite element models. Different heating methods including induction and resistive/radiation were evaluated. The temperature profiles of Martian samples in a proposed container structure were predicted. The results show that the sealing and sterilizing process can be controlled such that the samples temperature is maintained below the level that may cause damage, and that the brazing technique is a feasible approach to breaking the contamination path.

  13. EPIC Forest LAI Dataset: LAI estimates generated from the USDA Environmental Policy Impact Climate (EPIC) model (a widely used, field-scale, biogeochemical model) on four forest complexes spanning three physiographic provinces in VA and NC.

    Data.gov (United States)

    U.S. Environmental Protection Agency — This data depicts calculated and validated LAI estimates generated from the USDA Environmental Policy Impact Climate (EPIC) model (a widely used, field-scale,...

  14. Preparation of quality control samples for thyroid hormones T3 and T4 in radioimmunoassay techniques

    International Nuclear Information System (INIS)

    Ahmed, F.O.A.

    2006-03-01

    Today, the radioimmunoassay becomes one of the best techniques for quantitative analysis of very low concentration of different substances. RIA is being widely used in medical and research laboratories. To maintain high specificity and accuracy in RIA and other related techniques the quality controls must be introduced. In this dissertation quality control samples for thyroid hormones (Triiodothyronine T3 and Thyroxin T4), using RIA techniques. Ready made chinese T4, T3 RIA kits were used. IAEA statistical package were selected.(Author)

  15. Quality control of the analysis of IAEA samples in the radium institute

    International Nuclear Information System (INIS)

    Belyaev, B.N.; Lovtsus, A.V.; Makarova, T.P.; Stepanov, A.V.

    1989-01-01

    Metrological chracteristics of mass and alpha spectrometric methods in the Radium Institute for analysis of spent fuel control samples are evaluated. The techniques of analysis and the procedure of quality control for isotopic ratio measurements based on the use of uranium and plutonium standard reference materials (NBS, NBL, SAL made in USSR) are described. The results of measurements performed during cooperation with IAEA are discussed, and the sources of systematic and random errors are analyzed. The results obtained agree well with the target values. (author)

  16. The CEBAF control system for the CHL

    International Nuclear Information System (INIS)

    Keesee, M.S.; Bevins, B.S.

    1996-01-01

    The CEBAF Central Helium Liquefier (CHL) control system consists of independent safety controls located at each subsystem, CAMAC computer interface hardware, and a CEBAF-designed control software called Thaumaturgic Automated Control Logic (TACL). The paper describes how control software was interfaced with the subsystems of the CHL. Topics of configuration, editing, operator interface, datalogging, and internal logic functions are presented as they relate to the operational needs of the helium plant. The paper also describes the effort underway to convert from TACL to the Experimental Physics and Industrial Control System (EPICS), the new control system for the CEBAF accelerator. This software change will require customizing EPICS software to cryogenic process control

  17. Attitudes to Gun Control in an American Twin Sample: Sex Differences in the Causes of Variation.

    Science.gov (United States)

    Eaves, Lindon J; Silberg, Judy L

    2017-10-01

    The genetic and social causes of individual differences in attitudes to gun control are estimated in a sample of senior male and female twin pairs in the United States. Genetic and environmental parameters were estimated by weighted least squares applied to polychoric correlations for monozygotic (MZ) and dizygotic (DZ) twins of both sexes. The analysis suggests twin similarity for attitudes to gun control in men is entirely genetic while that in women is purely social. Although the volunteer sample is small, the analysis illustrates how the well-tested concepts and methods of genetic epidemiology may be a fertile resource for deepening our scientific understanding of biological and social pathways that affect individual risk to gun violence.

  18. A Pragmatic and Sociolinguistic Account of δαιμόνιε in Early Greek Epic

    Directory of Open Access Journals (Sweden)

    H. Paul Brown

    2011-11-01

    Full Text Available Consideration of the social standing and emotional relation of speaker to addressee in epic shows that the address daimonie implies negative disposition and surprise, not the friendship term that would emerge later.

  19. A development environment for the SSC control system

    International Nuclear Information System (INIS)

    Murray, Doug; Martinsen, Garth; Wang, Judy

    1994-01-01

    The SSC is developing a design environment for control system development within the context of EPICS. The environment is aimed at developers of applications using the EPICS Input/Output Controller (IOC). The unique aspect of this effort is our emphasis on providing a simple and intuitive development environment compared with tools currently available. Our most important goal in this effort has been to hide the complexity of EPICS IOC development from the developers. This paper describes two tools which are under development; The Function Block Editor (FBE) and the State Machine Editor (SME). The FBE provides a visual editing environment for graphically describing control processes as a set of related functional blocks. The configuration of functional blocks is then translated into IOC records and executed. SME allows the user to visually construct a sequence using a notation we are modeling after Grafcet [1]. State machines are translated into EPICS State Notation Language programs and executed. Future extensions will be described. ((orig.))

  20. APPLICATION OF LOT QUALITY ASSURANCE SAMPLING FOR ASSESSING DISEASE CONTROL PROGRAMMES - EXAMINATION OF SOME METHODOLOGICAL ISSUES

    OpenAIRE

    T. R. RAMESH RAO

    2011-01-01

    Lot Quality Assurance Sampling (LQAS), a statistical tool in industrial setup, has been in use since 1980 for monitoring and evaluation of programs on disease control / immunization status among children / health workers performance in health system. While conducting LQAS in the field, there are occasions, even after due care of design, there are practical and methodological issues to be addressed before it is recommended for implementation and intervention. LQAS is applied under the assumpti...

  1. The cryogenic control system of BEPCⅡ

    Institute of Scientific and Technical Information of China (English)

    LI Gang; WANG Ke-Xiang; ZHAO Ji-Jiu; YUE Ke-Juan; DAI Ming-Sui; HUANG Yi-Ling; JIANG Bo

    2008-01-01

    A superconducting cryogenic system has been designed and deployed in the Beijing Electron-Positron Collider Upgrade Project(BEPCⅡ).The system consists of a Siemens PLC(ST-PLC,Programmable Logic Controller)for the compressor control,an Allen Bradley(AB)PLC for the cryogenic equipments,and the Experimental Physics and Industrial Control System(EPICS)that integrates the PLCs.The system fully automates the superconducting cryogenic control with process control,PID(Proportional-Integral-Differential)control loops,real-time data access and data storage,alarm handler and human machine interface.It is capable of automatic recovery as well.This paper describes the BEPCⅡ cryogenic control system,data communication between ST-PLC and EPICS Input/Output Controllers(IOCs),and the integration of the flow control,the low level interlock,the AB-PLC,and EPICS.

  2. Potential substitution of mineral P fertilizer by manure: EPIC development and implementation

    Science.gov (United States)

    Azevedo, Ligia B.; Vadas, Peter A.; Balkovič, Juraj; Skalský, Rastislav; Folberth, Christian; van der Velde, Marijn; Obersteiner, Michael

    2016-04-01

    Sources of mineral phosphorus (P) fertilizers are non-renewable. Although the longevity of P mines and the risk of future P depletion are highly debated P scarcity may be detrimental to agriculture in various ways. Some of these impacts include increasing food insecurity and nitrogen (N) and P imbalances, serious fluctuations in the global fertilizer and crop market prices, and contribution in geopolitical conflicts. P-rich waste produced from livestock production activities (i.e. manure) are an alternative to mineral P fertilizer. The substitution of mineral fertilizer with manure (1) delays the depletion of phosphate rock stocks, (2) reduces the vulnerability of P fertilizer importing countries to sudden changes in the fertilizer market, (3) reduces the chances of geopolitical conflicts arising from P exploitation pressures, (4) avoids the need for environmental protection policies in livestock systems, (5) is an opportunity for the boosting of crop yields in low nutrient input agricultural systems, and (6) contributes to the inflow of not only P but also other essential nutrients to agricultural soils. The Environmental Policy Integrated Climate model (EPIC) is a widely used process-based, crop model integrating various environmental flows relevant to crop production as well as environmental quality assessments. We simulate crop yields using a powerful computer cluster infra-structure (known as EPIC-IIASA) in combination with spatially-explicit EPIC input data on climate, management, soils, and landscape. EPIC-IIASA contains over 131,000 simulation units and it has 5 arc-min resolution. In this work, we implement two process-based models of manure biogeochemistry into EPIC-IIASA, i.e. SurPhos (for P) and Manure DNDC (for N and carbon) and a fate model model describing nutrient outflows from fertilizer via runoff. For EGU, we will use EPIC-IIASA to quantify the potential of mineral P fertilizer substitution with manure. Specifically, we will estimate the relative

  3. Calorimeters for Precision Power Dissipation Measurements on Controlled-Temperature Superconducting Radiofrequency Samples

    International Nuclear Information System (INIS)

    Xiao, Binping P.; Kelley, Michael J.; Reece, Charles E.; Phillips, H. L.

    2012-01-01

    Two calorimeters, with stainless steel and Cu as the thermal path material for high precision and high power versions, respectively, have been designed and commissioned for the surface impedance characterization (SIC) system at Jefferson Lab to provide low temperature control and measurement for CW power up to 22 W on a 5 cm dia. disk sample which is thermally isolated from the RF portion of the system. A power compensation method has been developed to measure the RF induced power on the sample. Simulation and experimental results show that with these two calorimeters, the whole thermal range of interest for superconducting radiofrequency (SRF) materials has been covered. The power measurement error in the interested power range is within 1.2% and 2.7% for the high precision and high power versions, respectively. Temperature distributions on the sample surface for both versions have been simulated and the accuracy of sample temperature measurements have been analysed. Both versions have the ability to accept bulk superconductors and thin film superconducting samples with a variety of substrate materials such as Al, Al 2 O 3 , Cu, MgO, Nb and Si

  4. Everyday temptations: an experience sampling study of desire, conflict, and self-control.

    Science.gov (United States)

    Hofmann, Wilhelm; Baumeister, Roy F; Förster, Georg; Vohs, Kathleen D

    2012-06-01

    How often and how strongly do people experience desires, to what extent do their desires conflict with other goals, and how often and successfully do people exercise self-control to resist their desires? To investigate desire and attempts to control desire in everyday life, we conducted a large-scale experience sampling study based on a conceptual framework integrating desire strength, conflict, resistance (use of self-control), and behavior enactment. A sample of 205 adults wore beepers for a week. They furnished 7,827 reports of desire episodes and completed personality measures of behavioral inhibition system/behavior activation system (BIS/BAS) sensitivity, trait self-control, perfectionism, and narcissistic entitlement. Results suggest that desires are frequent, variable in intensity, and largely unproblematic. Those urges that do conflict with other goals tend to elicit resistance, with uneven success. Desire strength, conflict, resistance, and self-regulatory success were moderated in multiple ways by personality variables as well as by situational and interpersonal factors such as alcohol consumption, the mere presence of others, and the presence of others who already had enacted the desire in question. Whereas personality generally had a stronger impact on the dimensions of desire that emerged early in its course (desire strength and conflict), situational factors showed relatively more influence on components later in the process (resistance and behavior enactment). In total, these findings offer a novel and detailed perspective on the nature of everyday desires and associated self-regulatory successes and failures. 2012 APA, all rights reserved

  5. Identification of clinical biomarkers for pre-analytical quality control of blood samples.

    Science.gov (United States)

    Kang, Hyun Ju; Jeon, Soon Young; Park, Jae-Sun; Yun, Ji Young; Kil, Han Na; Hong, Won Kyung; Lee, Mee-Hee; Kim, Jun-Woo; Jeon, Jae-Pil; Han, Bok Ghee

    2013-04-01

    Pre-analytical conditions are key factors in maintaining the high quality of biospecimens. They are necessary for accurate reproducibility of experiments in the field of biomarker discovery as well as achieving optimal specificity of laboratory tests for clinical diagnosis. In research at the National Biobank of Korea, we evaluated the impact of pre-analytical conditions on the stability of biobanked blood samples by measuring biochemical analytes commonly used in clinical laboratory tests. We measured 10 routine laboratory analytes in serum and plasma samples from healthy donors (n = 50) with a chemistry autoanalyzer (Hitachi 7600-110). The analyte measurements were made at different time courses based on delay of blood fractionation, freezing delay of fractionated serum and plasma samples, and at different cycles (0, 1, 3, 6, 9) of freeze-thawing. Statistically significant changes from the reference sample mean were determined using the repeated-measures ANOVA and the significant change limit (SCL). The serum levels of GGT and LDH were changed significantly depending on both the time interval between blood collection and fractionation and the time interval between fractionation and freezing of serum and plasma samples. The glucose level was most sensitive only to the elapsed time between blood collection and centrifugation for blood fractionation. Based on these findings, a simple formula (glucose decrease by 1.387 mg/dL per hour) was derived to estimate the length of time delay after blood collection. In addition, AST, BUN, GGT, and LDH showed sensitive responses to repeated freeze-thaw cycles of serum and plasma samples. These results suggest that GGT and LDH measurements can be used as quality control markers for certain pre-analytical conditions (eg, delayed processing or repeated freeze-thawing) of blood samples which are either directly used in the laboratory tests or stored for future research in the biobank.

  6. Control Charts for Processes with an Inherent Between-Sample Variation

    Directory of Open Access Journals (Sweden)

    Eva Jarošová

    2018-06-01

    Full Text Available A number of processes to which statistical control is applied are subject to various effects that cause random changes in the mean value. The removal of these fluctuations is either technologically impossible or economically disadvantageous under current conditions. The frequent occurrence of signals in the Shewhart chart due to these fluctuations is then undesirable and therefore the conventional control limits need to be extended. Several approaches to the design of the control charts with extended limits are presented in the paper and applied on the data from a real production process. The methods assume samples of size greater than 1. The performance of the charts is examined using the operating characteristic and average run length. The study reveals that in many cases, reducing the risk of false alarms is insufficient.

  7. Examination of weight control practices in a non-clinical sample of college women.

    Science.gov (United States)

    Hayes, S; Napolitano, M A

    2012-09-01

    The current study examined healthy weight control practices among a sample of college women enrolled at an urban university (N=715; age=19.87±1.16; 77.2% Caucasian; 13.4% African American, 7.2% Asian, 2.2% other races). Participants completed measures as part of an on-line study about health habits, behaviors, and attitudes. Items from the Three Factor Eating Questionnaire were selected and evaluated with exploratory factor analysis to create a healthy weight control practices scale. Results revealed that college women, regardless of weight status, used a comparable number (four of eight) of practices. Examination of racial differences between Caucasian and African American women revealed that normal weight African American women used significantly fewer strategies than Caucasian women. Of note, greater use of healthy weight control practices was associated with higher cognitive restraint, drive for thinness, minutes of physical activity, and more frequent use of compensatory strategies. Higher scores on measures of binge and disinhibited eating, body dissatisfaction, negative affect, and depressive symptoms were associated with greater use of healthy weight control practices by underweight/normal weight but not by overweight/obese college women. Results suggest that among a sample of college females, a combination of healthy and potentially unhealthy weight control practices occurs. Implications of the findings suggest the need for effective weight management and eating disorder prevention programs for this critical developmental life stage. Such programs should be designed to help students learn how to appropriately use healthy weight control practices, as motivations for use may vary by weight status.

  8. Classical and additional antiphospholipid antibodies in blood samples of ischemic stroke patients and healthy controls.

    Science.gov (United States)

    Carmel-Neiderman, Narin-Nard; Tanne, David; Goren, Idan; Rotman-Pikielny, Pnina; Levy, Yair

    2017-04-01

    Classical antiphospholipid antibodies (aPLa) are found in 6-25% of blood samples from stroke patients. The frequency of novel aPLa antibodies in blood samples of CVA patients is not known. Enzyme-linked immunosorbent assays (ELISA) were performed on blood samples from 209 CVA patients (170 samples were obtained during the acute phase and 39 samples were from patients with complete carotid stenosis) and compared to 54 healthy controls. Subjects were tested for the presence of the classical aPL antibodies anticardiolipin (aCL) and anti-beta2-glycoprotein (aβ2gI), in addition to antiphosphatidylethanolamine (aPE), anti-phosphatidylserine (aPS), and Annexin V. All antibodies were tested for both IgM and IgG subclasses. Numeric analysis of the antibody titer levels (μ/ml) revealed a significantly higher subclinical titer by two standard deviations of many aPL autoantibodies among CVA patients (Pv < 0.05). However, according to the kit manufacturer's cutoff value, no positive antibodies were found except a trend toward higher percentage of positive aPS IgG titer in the CVA group compared to controls (6.2 vs. %0; P = 0.077). According to the manufacturer's cutoff, significantly higher levels of positive antibodies were not found among stroke patients. However, the absolute ELISA values of stroke patients were significantly higher. These results suggest that lower cutoff values than those used for APS diagnosis should be used for risk stratification of CVA among healthy individuals.

  9. Microstructural controls on the macroscopic behavior of geo-architected rock samples

    Science.gov (United States)

    Mitchell, C. A.; Pyrak-Nolte, L. J.

    2017-12-01

    Reservoir caprocks, are known to span a range of mechanical behavior from elastic granitic units to visco-elastic shale units. Whether a rock will behave elastically, visco-elastically or plastically depends on both the compositional and textural or microsctructural components of the rock, and how these components are spatially distributed. In this study, geo-architected caprock fabrication was performed to develop synthetic rock to study the role of rock rheology on fracture deformations, fluid flow and geochemical alterations. Samples were geo-architected with Portland Type II cement, Ottawa sand, and different clays (kaolinite, illite, and Montmorillonite). The relative percentages of these mineral components are manipulated to generate different rock types. With set protocols, the mineralogical content, texture, and certain structural aspects of the rock were controlled. These protocols ensure that identical samples with the same morphological and mechanical characteristics are constructed, thus overcoming issues that may arise in the presence of heterogeneity and high anisotropy from natural rock samples. Several types of homogeneous geo-architected rock samples were created, and in some cases the methods were varied to manipulate the physical parameters of the rocks. Characterization of rocks that the samples exhibit good repeatability. Rocks with the same mineralogical content generally yielded similar compressional and shear wave velocities, UCS and densities. Geo-architected rocks with 10% clay in the matrix had lower moisture content and effective porosities than rocks with no clay. The process by which clay is added to the matrix can strongly affect the resulting compressive strength and physical properties of the geo-architected sample. Acknowledgment: This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Geosciences Research Program under Award Number (DE-FG02-09ER16022).

  10. European Prospective Investigation into Cancer and Nutrition (EPIC) calibration study: rationale, design and population characteristics

    DEFF Research Database (Denmark)

    Slimani, N.; Kaaks, R.; Ferrari, P.

    2002-01-01

    The European Prospective Investigation into Cancer and Nutrition (EPIC), which covers a large cohort of half a million men and women from 23 European centres in 10 Western European countries, was designed to study the relationship between diet and the risk of chronic diseases, particularly cancer......, a calibration approach was developed. This approach involved an additional dietary assessment common across study populations to re-express individual dietary intakes according to the same reference scale. A single 24-hour diet recall was therefore collected, as the EPIC reference calibration method, from...... in a large multi-centre European study. These studies showed that, despite certain inherent methodological and logistic constraints, a study design such as this one works relatively well in practice. The average response in the calibration study was 78.3% and ranged from 46.5% to 92.5%. The calibration...

  11. Diversity of dietary patterns observed in the European Prospective Investigation into Cancer and Nutrition (EPIC) project

    DEFF Research Database (Denmark)

    Slimani, N.; Fahey, M.; Welch, A.A.

    2002-01-01

    differences were observed across centres, the countries participating in EPIC are characterised by specific dietary patterns. Overall, Italy and Greece have a dietary pattern characterised by plant foods (except potatoes) and a lower consumption of animal and processed foods, compared with the other EPIC...... countries. France and particularly Spain have more heterogeneous dietary patterns, with a relatively high consumption of both plant foods and animal products. Apart from characteristics specific to vegetarian groups, the UK 'health-conscious' group shares with the UK general population a relatively high...... consumption of tea, sauces, cakes, soft drinks (women), margarine and butter. In contrast, the diet in the Nordic countries, The Netherlands, Germany and the UK general population is relatively high in potatoes and animal, processed and sweetened/refined foods, with proportions varying across countries...

  12. Analisis Efektivitas Iklan Jejaring Sosial sebagai Media Promosi Menggunakan EPIC Model

    Directory of Open Access Journals (Sweden)

    Nur Hasanah

    2016-02-01

    Full Text Available Keberhasilan dalam sebuah iklan atau promosi yang sesuai dengan kebutuhan masyarakat terhadap Informasi Layanan Pendidikan di jejaring sosial sangat bergantung pada kemasan tampilan yang menarik dan berita yang disampaikan. Pencapaian keberhasilan tujuan promosi tersebut akan membutuhkan tindakan yang berkesinambungan dan tepat sasaran. Untuk mengetahui apakah Facebook Huma Harati itu efektif atau tidak maka perlu adanya pengukuran terhadap Facebook itu sendiri, salah satunya menggunakan metode EPIC (Empaty, Persuation, Impact, and Communication. Hasil analisa menyatakan bahwa Fanpage Huma Harati merupakan tempat yang efektif sebagai media promosi, hal ini terlihat dari nilai empaty, persuasiona, impact and communication yang diperoleh. Nilai rata-rata pada EPIC rate adalah 3,978, dimensi komunikasi mendapat nilai tertinggi dari dimensi lainnya yaitu 4,02. 

  13. Air and smear sample calculational tool for Fluor Hanford Radiological control

    International Nuclear Information System (INIS)

    BAUMANN, B.L.

    2003-01-01

    A spreadsheet calculation tool was developed to automate the calculations performed for determining the concentration of airborne radioactivity and smear counting as outlined in HNF--13536, Section 5.2.7, ''Analyzing Air and Smear Samples''. This document reports on the design and testing of the calculation tool. Radiological Control Technicians (RCTs) will save time and reduce hand written and calculation errors by using an electronic form for documenting and calculating work place air samples. Current expectations are RCTs will perform an air sample and collect the filter or perform a smear for surface contamination. RCTs will then survey the filter for gross alpha and beta/gamma radioactivity and with the gross counts utilize either hand calculation method or a calculator to determine activity on the filter. The electronic form will allow the RCT with a few key strokes to document the individual's name, payroll, gross counts, instrument identifiers; produce an error free record. This productivity gain is realized by the enhanced ability to perform mathematical calculations electronically (reducing errors) and at the same time, documenting the air sample

  14. Control sample design using a geodemographic discriminator: An application of Super Profiles

    Science.gov (United States)

    Brown, Peter J. B.; McCulloch, Peter G.; Williams, Evelyn M. I.; Ashurst, Darren C.

    The development and application of an innovative sampling framework for use in a British study of the early detection of gastric cancer are described. The Super Profiles geodemographic discriminator is used in the identification of geographically distinct control and contrast areas from which samples of cancer registry case records may be drawn for comparison with the records of patients participating in the gastric cancer intervention project. Preliminary results of the application of the framework are presented and confirm its effectiveness in satisfactorily reflecting known patterns of variation in cancer occurrence by age, gender and social class. The method works well for cancers with a known and clear social gradient, such as lung and breast cancer, moderately well for gastric cancer and somewhat less well for oesophageal cancer, where the social class gradient is less clear.

  15. Automated injection of a radioactive sample for preparative HPLC with feedback control

    International Nuclear Information System (INIS)

    Iwata, Ren; Yamazaki, Shigeki

    1990-01-01

    The injection of a radioactive reaction mixture into a preparative HPLC column has been automated with computer control for rapid purification of routinely prepared positron emitting radiopharmaceuticals. Using pneumatic valves, a motor-driven pump and a liquid level sensor, two intelligent injection methods for the automation were compared with regard to efficient and rapid sample loading into a 2 mL loop of the 6-way valve. One, a precise but rather slow method, was demonstrated to be suitable for purification of 18 F-radiopharmaceuticals, while the other, due to its rapid operation, was more suitable for 11 C-radiopharmaceuticals. A sample volume of approx 0.5 mL can be injected onto a preparative HPLC column with over 90% efficiency with the present automated system. (author)

  16. EPIC: A Testbed for Scientifically Rigorous Cyber-Physical Security Experimentation

    OpenAIRE

    SIATERLIS CHRISTOS; GENGE BELA; HOHENADEL MARC

    2013-01-01

    Recent malware, like Stuxnet and Flame, constitute a major threat to Networked Critical Infrastructures (NCIs), e.g., power plants. They revealed several vulnerabilities in today's NCIs, but most importantly they highlighted the lack of an efficient scientific approach to conduct experiments that measure the impact of cyber threats on both the physical and the cyber parts of NCIs. In this paper we present EPIC, a novel cyber-physical testbed and a modern scientific instrument that can pr...

  17. Fuel and coolant motions following pin failure: EPIC models and the PBE-5S experiment

    International Nuclear Information System (INIS)

    Garner, P.L.; Abramson, P.B.

    1979-01-01

    The EPIC computer code has been used to analyze the post-fuel-pin-failure behavior in the PBE-5S experiment performed at Sandia Laboratories. The effects of modeling uncertainties on the calculation are examined. The calculations indicate that the majority of the piston motion observed in the test is due to the initial pressurization of the coolant channel by fuel vapor at cladding failure. A more definitive analysis requires improvements in calculational capabilities and experiment diagnostics

  18. Sampled control of vibration in suspended cask by using vibration manipulation functions

    International Nuclear Information System (INIS)

    Kotake, Shigeo

    2014-01-01

    Safe and reliable operation is most important for decommissioning the Fukushima 1 nuclear power plant. Especially it requires for transferring spent nuclear fuels from fuel pool to storage cask. Since the heavy cask will be suspended during the transferring operation, there is a risk of dropping it in case of the strike of large earthquakes. In this study, we introduce analytical functions to suppress residual vibration of a suspended cask by using vibration manipulation function. Hence the oscillation of the cask can be feedforward or sampled-data controlled by moving a trolley with analog actuator, the possible risk could be reduced. (author)

  19. Macronutrient, vitamin, and mineral intakes in the EPIC-Germany cohorts.

    Science.gov (United States)

    Schulze, M B; Linseisen, J; Kroke, A; Boeing, H

    2001-01-01

    This article presents intakes of nutrients in the EPIC-Heidelberg and the EPIC-Potsdam (European Investigation into Cancer and Nutrition) studies. Estimates are based on standardized 24-hour dietary recalls. Recalls from 1,013 men and 1,078 women in Heidelberg and from 1,032 men and 898 women in Potsdam were included in the analysis. The estimated nutrient intake was based on the German Food Code and Nutrient Data Base version II.3. Analyses were carried out stratified by sex and weighted for the day of the week and age. Men in Potsdam reported significantly higher intakes of energy (mean Potsdam = 10,718 kJ, mean Heidelberg = 10,387 kJ) and higher intakes of vitamins and minerals as compared with men in Heidelberg. However, Heidelberg men consumed more alcohol, alpha-tocopherol, phosphorus, calcium, and magnesium. Potsdam women reported lower energy (mean Potsdam = 7,537 kJ, mean Heidelberg = 7,855 kJ), alcohol, and cholesterol intakes as compared with Heidelberg women. Vitamin and mineral intakes were lower too, except for retinol and ascorbic acid. The intakes of energy and most nutrients observed in the Potsdam and Heidelberg study populations were within the range reported from other German studies. The observed differences between both study populations indicate different dietary patterns, increasing the exposure variation in the EPIC study. Copyright 2001 S. Karger AG, Basel

  20. Connection of control circuits of machine for automatic measurement of radioactive samples

    International Nuclear Information System (INIS)

    Vorlicek, J.

    1984-01-01

    A windowless through-flow gas detector is used for measurement. The automatic machine is controlled by four flip-flops defining the following states: the dish replacement in the measuring space, washing, measurement, measured value print-out, and resetting. The first and second outputs of the first, second and third flip-flops are connected to six inputs of a block whose four outputs provide counter reset and stop-watch reset, washing, measurement, and print-out. Such machine control eliminates measurement errors by disabling sample measurement until air is removed from the measurement space, introduced on an unwashed dish or on several dishes passed under the detector. The elimination of this error is also guaranteed in manual operation. (M.D.)

  1. Sequence analysis of the canine mitochondrial DNA control region from shed hair samples in criminal investigations.

    Science.gov (United States)

    Berger, C; Berger, B; Parson, W

    2012-01-01

    In recent years, evidence from domestic dogs has increasingly been analyzed by forensic DNA testing. Especially, canine hairs have proved most suitable and practical due to the high rate of hair transfer occurring between dogs and humans. Starting with the description of a contamination-free sample handling procedure, we give a detailed workflow for sequencing hypervariable segments (HVS) of the mtDNA control region from canine evidence. After the hair material is lysed and the DNA extracted by Phenol/Chloroform, the amplification and sequencing strategy comprises the HVS I and II of the canine control region and is optimized for DNA of medium-to-low quality and quantity. The sequencing procedure is based on the Sanger Big-dye deoxy-terminator method and the separation of the sequencing reaction products is performed on a conventional multicolor fluorescence detection capillary electrophoresis platform. Finally, software-aided base calling and sequence interpretation are addressed exemplarily.

  2. Synchronization of Hierarchical Time-Varying Neural Networks Based on Asynchronous and Intermittent Sampled-Data Control.

    Science.gov (United States)

    Xiong, Wenjun; Patel, Ragini; Cao, Jinde; Zheng, Wei Xing

    In this brief, our purpose is to apply asynchronous and intermittent sampled-data control methods to achieve the synchronization of hierarchical time-varying neural networks. The asynchronous and intermittent sampled-data controllers are proposed for two reasons: 1) the controllers may not transmit the control information simultaneously and 2) the controllers cannot always exist at any time . The synchronization is then discussed for a kind of hierarchical time-varying neural networks based on the asynchronous and intermittent sampled-data controllers. Finally, the simulation results are given to illustrate the usefulness of the developed criteria.In this brief, our purpose is to apply asynchronous and intermittent sampled-data control methods to achieve the synchronization of hierarchical time-varying neural networks. The asynchronous and intermittent sampled-data controllers are proposed for two reasons: 1) the controllers may not transmit the control information simultaneously and 2) the controllers cannot always exist at any time . The synchronization is then discussed for a kind of hierarchical time-varying neural networks based on the asynchronous and intermittent sampled-data controllers. Finally, the simulation results are given to illustrate the usefulness of the developed criteria.

  3. Rectal swab screening assays of public health importance in molecular diagnostics: Sample adequacy control.

    Science.gov (United States)

    Glisovic, Sanja; Eintracht, Shaun; Longtin, Yves; Oughton, Matthew; Brukner, Ivan

    Rectal swabs are routinely used by public health authorities to screen for multi-drug resistant enteric bacteria including vancomycin-resistant enterococci (VRE) and carbapenem-resistant enterobacteriaceae (CRE). Screening sensitivity can be influenced by the quality of the swabbing, whether performed by the patient (self-swabbing) or a healthcare practitioner. One common exclusion criterion for rectal swabs is absence of "visible soiling" from fecal matter. In our institution, this criterion excludes almost 10% of rectal swabs received in the microbiology laboratory. Furthermore, over 30% of patients in whom rectal swabs are cancelled will not be re-screened within the next 48h, resulting in delays in removing infection prevention measures. We describe two quantitative polymerase chain reaction (qPCR)-based assays, human RNAse P and eubacterial 16S rDNA, which might serve as suitable controls for sampling adequacy. However, lower amounts of amplifiable human DNA make the 16s rDNA assay a better candidate for sample adequacy control. Copyright © 2017. Published by Elsevier Ltd.

  4. Remote control air sampling and fast chemical analysis of the composition

    Energy Technology Data Exchange (ETDEWEB)

    Kukuczka, A; Golisz, T

    1981-01-01

    In 1979 the Central mine rescue station in Bytom (Poland) developed and introduced into use a new method of remote control air and gas (from fires) sampling and swift chemical analysis of the samples' composition. The device in this method includes: a probe (situated beyond the fire detector directly in the control zone), thick-walled elastic hose, direr, piston pump, rotameter, chromatograph and minicomputer. The basic technical data included in the set: the capacity of the pump 8 1/min, 2.5 kg mass. run on 12 V current (built at the Main Mining Affairs Inst. in Poland); the chromatograph is VARIAN 1420-10 (USA produced),the working gas is helium (balloon volume 40 1), feed--alternating 220V, capacity--1.5 kW, time for measuring gas from fires-- 15 to 20 min (as apposed to the 1.5h spent before when the SRC device was being used) at an accuracy of /sup + -/ 0.05% (volume); the chromatograph works with a mini-computer (model CDS-111C) with a 20 kg mass.and a size of 16 x 46 x 56 cm. As tests in Moszczenica coal mines, where a fire in 504/2 occurred, showed (the chromatograph was located 750m from the probe for burning gases), the method proved to be a good one although the VARIAN 1420-10 was insufficiently reliable and the VARIAN-1400-AEROGRAF proved to be better.

  5. The German version of the Expanded Prostate Cancer Index Composite (EPIC): translation, validation and minimal important difference estimation.

    Science.gov (United States)

    Umbehr, Martin H; Bachmann, Lucas M; Poyet, Cedric; Hammerer, Peter; Steurer, Johann; Puhan, Milo A; Frei, Anja

    2018-02-20

    No official German translation exists for the 50-item Expanded Prostate Cancer Index Composite (EPIC), and no minimal important difference (MID) has been established yet. The aim of the study was to translate and validate a German version of the EPIC with cultural adaptation to the different German speaking countries and to establish the MID. We translated and culturally adapted the EPIC into German. For validation, we included a consecutive subsample of 92 patients with localized prostate cancer undergoing radical prostatectomy who participated the Prostate Cancer Outcomes Cohort. Baseline and follow-up assessments took place before and six weeks after prostatectomy in 2010 and 2011. We assessed the EPIC, EORTC QLQ-PR25, Feeling Thermometer, SF-36 and a global rating of health state change variable. We calculated the internal consistency, test-retest reliability, construct validity, responsiveness and MID. For most EPIC domains and subscales, our a priori defined criteria for reliability were fulfilled (construct reliability: Cronbach's alpha 0.7-0.9; test-retest reliability: intraclass-correlation coefficient ≥ 0.7). Cross-sectional and longitudinal correlations between EPIC and EORTC QLQ-PR25 domains ranged from 0.14-0.79, and 0.06-0.5 and 0.08-0.72 for Feeling Thermometer and SF-36, respectively. We established MID values of 10, 4, 12, and 6 for the urinary, bowel, sexual and hormonal domain. The German version of the EPIC is reliable, responsive and valid to measure HRQL in prostate cancer patients and is now available in German language. With the suggested MID we provide interpretation to what extent changes in HRQL are clinically relevant for patients. Hence, study results are of interest beyond German speaking countries.

  6. Job Stress and Locus of Control in Teachers: Comparisons between Samples from the United States and Zimbabwe

    Science.gov (United States)

    Crothers, Laura M.; Kanyongo, Gibbs Y.; Kolbert, Jered B.; Lipinski, John; Kachmar, Steven P.; Koch, Gary D.

    2010-01-01

    This study examines the relationship between educators' locus of control and job stress using samples from the US and Zimbabwe. Multiple regression analyses are used to identify significant relationships in the US sample between teachers' external locus of control and the severity of the job stress that they experience, coupled with the perceived…

  7. System design specification for rotary mode core sample trucks No. 2, 3, and 4 programmable logic controller

    International Nuclear Information System (INIS)

    Dowell, J.L.; Akers, J.C.

    1995-01-01

    The system this document describes controls several functions of the Core Sample Truck(s) used to obtain nuclear waste samples from various underground storage tanks at Hanford. The system will monitor the sampling process and provide alarms and other feedback to insure the sampling process is performed within the prescribed operating envelope. The intended audience for this document is anyone associated with rotary or push mode core sampling. This document describes the Alarm and Control logic installed on Rotary Mode Core Sample Trucks (RMCST) number-sign 2, 3, and 4. It is intended to define the particular requirements of the RMCST alarm and control operation (not defined elsewhere) sufficiently for detailed design to implement on a Programmable Logic Controller (PLC)

  8. Statistical Power and Optimum Sample Allocation Ratio for Treatment and Control Having Unequal Costs Per Unit of Randomization

    Science.gov (United States)

    Liu, Xiaofeng

    2003-01-01

    This article considers optimal sample allocation between the treatment and control condition in multilevel designs when the costs per sampling unit vary due to treatment assignment. Optimal unequal allocation may reduce the cost from that of a balanced design without sacrificing any power. The optimum sample allocation ratio depends only on the…

  9. Randomized controlled trial of attention bias modification in a racially diverse, socially anxious, alcohol dependent sample.

    Science.gov (United States)

    Clerkin, Elise M; Magee, Joshua C; Wells, Tony T; Beard, Courtney; Barnett, Nancy P

    2016-12-01

    Attention biases may be an important treatment target for both alcohol dependence and social anxiety. This is the first ABM trial to investigate two (vs. one) targets of attention bias within a sample with co-occurring symptoms of social anxiety and alcohol dependence. Additionally, we used trial-level bias scores (TL-BS) to capture the phenomena of attention bias in a more ecologically valid, dynamic way compared to traditional attention bias scores. Adult participants (N = 86; 41% Female; 52% African American; 40% White) with elevated social anxiety symptoms and alcohol dependence were randomly assigned to an 8-session training condition in this 2 (Social Anxiety ABM vs. Social Anxiety Control) by 2 (Alcohol ABM vs. Alcohol Control) design. Symptoms of social anxiety, alcohol dependence, and attention bias were assessed across time. Multilevel models estimated the trajectories for each measure within individuals, and tested whether these trajectories differed according to the randomized training conditions. Across time, there were significant or trending decreases in all attention TL-BS parameters (but not traditional attention bias scores) and most symptom measures. However, there were not significant differences in the trajectories of change between any ABM and control conditions for any symptom measures. These findings add to previous evidence questioning the robustness of ABM and point to the need to extend the effects of ABM to samples that are racially diverse and/or have co-occurring psychopathology. The results also illustrate the potential importance of calculating trial-level attention bias scores rather than only including traditional bias scores. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Randomized Controlled Trial of Attention Bias Modification in a Racially Diverse, Socially Anxious, Alcohol Dependent Sample

    Science.gov (United States)

    Clerkin, Elise M.; Magee, Joshua C.; Wells, Tony T.; Beard, Courtney; Barnett, Nancy P.

    2016-01-01

    Objective Attention biases may be an important treatment target for both alcohol dependence and social anxiety. This is the first ABM trial to investigate two (vs. one) targets of attention bias within a sample with co-occurring symptoms of social anxiety and alcohol dependence. Additionally, we used trial-level bias scores (TL-BS) to capture the phenomena of attention bias in a more ecologically valid, dynamic way compared to traditional attention bias scores. Method Adult participants (N=86; 41% Female; 52% African American; 40% White) with elevated social anxiety symptoms and alcohol dependence were randomly assigned to an 8-session training condition in this 2 (Social Anxiety ABM vs. Social Anxiety Control) by 2 (Alcohol ABM vs. Alcohol Control) design. Symptoms of social anxiety, alcohol dependence, and attention bias were assessed across time. Results Multilevel models estimated the trajectories for each measure within individuals, and tested whether these trajectories differed according to the randomized training conditions. Across time, there were significant or trending decreases in all attention TL-BS parameters (but not traditional attention bias scores) and most symptom measures. However, there were not significant differences in the trajectories of change between any ABM and control conditions for any symptom measures. Conclusions These findings add to previous evidence questioning the robustness of ABM and point to the need to extend the effects of ABM to samples that are racially diverse and/or have co-occurring psychopathology. The results also illustrate the potential importance of calculating trial-level attention bias scores rather than only including traditional bias scores. PMID:27591918

  11. Physical Activity, Bone Health, and Obesity in Peri-/Pre- and Postmenopausal Women: Results from the EPIC-Potsdam Study.

    Science.gov (United States)

    Menzel, Juliane; di Giuseppe, Romina; Wientzek, Angelika; Kroke, Anja; Boeing, Heiner; Weikert, Cornelia

    2015-10-01

    Physical activity (PA) is suggested to increase the peak bone mass and to minimize age-related bone loss, and thereby to reduce the risk of osteoporosis. However, the relation between PA and bone health considering the obesity status is unclear so far. The present study examines the association between PA levels and calcaneal broadband ultrasound attenuation (BUA), particularly under consideration of obesity. Data from a population-based sample of 6776 German women from the EPIC-Potsdam cohort were analyzed. Calibrated PA data were used. Statistical analyses were stratified by menopausal and obesity status. Multiple linear regression was used to model the relationship between PA and BUA levels after adjustment for age, body mass index (BMI), smoking status, education, alcohol and calcium intake, and hormone use. Peri-/premenopausal had higher BUA levels (112.39 ± 10.05 dB/MHz) compared to postmenopausal women (106.44 ± 9.95 dB/MHz). In both groups, BUA levels were higher in the fourth compared to the lowest quartile of PA (p for trend obesity, a significant positive relationship was also observed in women with BMI < 30 kg/m(2) but with higher waist circumference or BF%. In conclusion, our results strengthen the hypothesis that PA has a positive influence on BUA levels, though dependent on weight.

  12. Normalization of RNA-seq data using factor analysis of control genes or samples

    Science.gov (United States)

    Risso, Davide; Ngai, John; Speed, Terence P.; Dudoit, Sandrine

    2015-01-01

    Normalization of RNA-seq data has proven essential to ensure accurate inference of expression levels. Here we show that usual normalization approaches mostly account for sequencing depth and fail to correct for library preparation and other more-complex unwanted effects. We evaluate the performance of the External RNA Control Consortium (ERCC) spike-in controls and investigate the possibility of using them directly for normalization. We show that the spike-ins are not reliable enough to be used in standard global-scaling or regression-based normalization procedures. We propose a normalization strategy, remove unwanted variation (RUV), that adjusts for nuisance technical effects by performing factor analysis on suitable sets of control genes (e.g., ERCC spike-ins) or samples (e.g., replicate libraries). Our approach leads to more-accurate estimates of expression fold-changes and tests of differential expression compared to state-of-the-art normalization methods. In particular, RUV promises to be valuable for large collaborative projects involving multiple labs, technicians, and/or platforms. PMID:25150836

  13. Test bed for real-time image acquisition and processing systems based on FlexRIO, CameraLink, and EPICS

    International Nuclear Information System (INIS)

    Barrera, E.; Ruiz, M.; Sanz, D.; Vega, J.; Castro, R.; Juárez, E.; Salvador, R.

    2014-01-01

    Highlights: • The test bed allows for the validation of real-time image processing techniques. • Offers FPGA (FlexRIO) image processing that does not require CPU intervention. • Is fully compatible with the architecture of the ITER Fast Controllers. • Provides flexibility and easy integration in distributed experiments based on EPICS. - Abstract: Image diagnostics are becoming standard ones in nuclear fusion. At present, images are typically analyzed off-line. However, real-time processing is occasionally required (for instance, hot-spot detection or pattern recognition tasks), which will be the objective for the next generation of fusion devices. In this paper, a test bed for image generation, acquisition, and real-time processing is presented. The proposed solution is built using a Camera Link simulator, a Camera Link frame-grabber, a PXIe chassis, and offers software interface with EPICS. The Camera Link simulator (PCIe card PCIe8 DVa C-Link from Engineering Design Team) generates simulated image data (for example, from video-movies stored in fusion databases) using a Camera Link interface to mimic the frame sequences produced with diagnostic cameras. The Camera Link frame-grabber (FlexRIO Solution from National Instruments) includes a field programmable gate array (FPGA) for image acquisition using a Camera Link interface; the FPGA allows for the codification of ad-hoc image processing algorithms using LabVIEW/FPGA software. The frame grabber is integrated in a PXIe chassis with system architecture similar to that of the ITER Fast Controllers, and the frame grabber provides a software interface with EPICS to program all of its functionalities, capture the images, and perform the required image processing. The use of these four elements allows for the implementation of a test bed system that permits the development and validation of real-time image processing techniques in an architecture that is fully compatible with that of the ITER Fast Controllers

  14. Discordant genotyping results using DNA isolated from anti-doping control urine samples.

    Science.gov (United States)

    Choong, Eva; Schulze, Jenny J; Ericsson, Magnus; Rane, Anders; Ekström, Lena

    2017-07-01

    The UGT2B17 gene deletion polymorphism is known to correlate to urinary concentration of testosterone-glucuronide and hence this genotype exerts a large impact on the testosterone/epitestosterone (T/E) ratio, a biomarker for testosterone doping. The objective of this study was to assess if DNA isolated from athletes' urine samples (n = 713) obtained in routine doping controls could be targeted for genotyping analysis for future integration in the athlete's passport. A control population (n = 21) including both urine and blood DNA was used for genotyping concordance test. Another aim was to study a large group (n = 596) of authentic elite athletes in respect of urinary steroid profile in relation to genetic variation. First we found that the genotype results when using urine-derived DNA did not correlate sufficiently with the genotype obtained from whole blood DNA. Secondly we found males with one or two UGT2B17 alleles had higher T/E (mean 1.63 ± 0.93) than females (mean 1.28 ± 1.08), p˂0.001. Unexpectedly, we found that several male del/del athletes in power sports had a T/E ˃1. If men in power sport exert a different urinary steroid profile needs to be further investigated. The other polymorphisms investigated in the CYP17A1, UGT2B7 and UGT2B15 genes did not show any associations with testosterone and epitestosterone concentrations. Our results show that genotyping using urine samples according to our method is not useful in an anti-doping setting. Instead, it is of importance for the anti-doping test programs to include baseline values in the ABP to minimize any putative impact of genotype. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  15. Transcriptome sequencing of the Microarray Quality Control (MAQC RNA reference samples using next generation sequencing

    Directory of Open Access Journals (Sweden)

    Thierry-Mieg Danielle

    2009-06-01

    Full Text Available Abstract Background Transcriptome sequencing using next-generation sequencing platforms will soon be competing with DNA microarray technologies for global gene expression analysis. As a preliminary evaluation of these promising technologies, we performed deep sequencing of cDNA synthesized from the Microarray Quality Control (MAQC reference RNA samples using Roche's 454 Genome Sequencer FLX. Results We generated more that 3.6 million sequence reads of average length 250 bp for the MAQC A and B samples and introduced a data analysis pipeline for translating cDNA read counts into gene expression levels. Using BLAST, 90% of the reads mapped to the human genome and 64% of the reads mapped to the RefSeq database of well annotated genes with e-values ≤ 10-20. We measured gene expression levels in the A and B samples by counting the numbers of reads that mapped to individual RefSeq genes in multiple sequencing runs to evaluate the MAQC quality metrics for reproducibility, sensitivity, specificity, and accuracy and compared the results with DNA microarrays and Quantitative RT-PCR (QRTPCR from the MAQC studies. In addition, 88% of the reads were successfully aligned directly to the human genome using the AceView alignment programs with an average 90% sequence similarity to identify 137,899 unique exon junctions, including 22,193 new exon junctions not yet contained in the RefSeq database. Conclusion Using the MAQC metrics for evaluating the performance of gene expression platforms, the ExpressSeq results for gene expression levels showed excellent reproducibility, sensitivity, and specificity that improved systematically with increasing shotgun sequencing depth, and quantitative accuracy that was comparable to DNA microarrays and QRTPCR. In addition, a careful mapping of the reads to the genome using the AceView alignment programs shed new light on the complexity of the human transcriptome including the discovery of thousands of new splice variants.

  16. Correcting Classifiers for Sample Selection Bias in Two-Phase Case-Control Studies

    Science.gov (United States)

    Theis, Fabian J.

    2017-01-01

    Epidemiological studies often utilize stratified data in which rare outcomes or exposures are artificially enriched. This design can increase precision in association tests but distorts predictions when applying classifiers on nonstratified data. Several methods correct for this so-called sample selection bias, but their performance remains unclear especially for machine learning classifiers. With an emphasis on two-phase case-control studies, we aim to assess which corrections to perform in which setting and to obtain methods suitable for machine learning techniques, especially the random forest. We propose two new resampling-based methods to resemble the original data and covariance structure: stochastic inverse-probability oversampling and parametric inverse-probability bagging. We compare all techniques for the random forest and other classifiers, both theoretically and on simulated and real data. Empirical results show that the random forest profits from only the parametric inverse-probability bagging proposed by us. For other classifiers, correction is mostly advantageous, and methods perform uniformly. We discuss consequences of inappropriate distribution assumptions and reason for different behaviors between the random forest and other classifiers. In conclusion, we provide guidance for choosing correction methods when training classifiers on biased samples. For random forests, our method outperforms state-of-the-art procedures if distribution assumptions are roughly fulfilled. We provide our implementation in the R package sambia. PMID:29312464

  17. Adrenal hormones before and after venography during adrenal venous sampling: a self-controlled study.

    Science.gov (United States)

    Koike, Yuya; Matsui, Seishi; Omura, Masao; Makita, Kohzoh; Obara, Alfonso W D; Moriya, Nobukazu; Nishikawa, Tetsuo

    2017-03-01

    A stress reaction involving increased adrenal hormone release occurs when starting adrenal venous sampling (AVS). The purpose of the present study was to investigate the effect of single shot venography on adrenal hormone production during AVS. This was a prospective self-controlled study. We enrolled 54 consecutive patients (21 men, 33 women; mean age 52 ± 11 years) with primary aldosteronism who underwent AVS from May 2014 to February 2015. Under non-stimulated conditions, blood samples were obtained from a common trunk of the left adrenal vein before and after single shot venography. The initial plasma aldosterone and cortisol concentration (PAC and PCC) were compared with those measured after venography for each patient. PAC and PCC were slightly but significantly decreased between before and after venography (after log transformation 2.12 ± 0.73 vs 2.07 ± 0.72, P = 0.00066, 1.89 ± 0.52 vs 1.83 ± 0.53, P = 0.00031, respectively). During non-stimulated left AVS, adrenal hormone secretion was slightly but significantly decreased after venography, similar to the normal time-related stress reaction. Venography did not increase the adrenal hormone secretion.

  18. Microcomputer-based systems for automatic control of sample irradiation and chemical analysis of short-lived isotopes

    International Nuclear Information System (INIS)

    Bourret, S.C.

    1974-01-01

    Two systems resulted from the need for the study of the nuclear decay of short-lived radionuclides. Automation was required for better repeatability, speed of chemical separation after irradiation and for protection from the high radiation fields of the samples. A MCS-8 computer was used as the nucleus of the automatic sample irradiation system because the control system required an extensive multiple-sequential circuit. This approach reduced the sequential problem to a computer program. The automatic chemistry control system is a mixture of a fixed and a computer-based programmable control system. The fixed control receives the irradiated liquid sample from the reactor, extracts the liquid and disposes of the used sample container. The programmable control executes the chemistry program that the user has entered through the teletype. (U.S.)

  19. Virtualization in control system environment

    International Nuclear Information System (INIS)

    Shen, L.R.; Liu, D.K.; Wan, T.M.

    2012-01-01

    In large scale distributed control system, there are lots of common service composed an environment for the entire control system, such as the server system for the common software base library, application server, archive server and so on. This paper gives a description of a virtualization realization for control system environment including the virtualization for server, storage, network system and application for the control system. With a virtualization instance of the EPICS based control system environment that was built by the VMware vSphere v4, we tested the whole functionality of this virtualization environment in the SSRF control system, including the common server of the NFS, NIS, NTP, Boot and EPICS base and extension library tools, we also have applied virtualization to application servers such as the Archive, Alarm, EPICS gateway and all of the network based IOC. Specially, we test the high availability and VMotion for EPICS asynchronous IOC successful under the different VLAN configuration of the current SSRF control system network. (authors)

  20. Robust Adaptive Stabilization of Linear Time-Invariant Dynamic Systems by Using Fractional-Order Holds and Multirate Sampling Controls

    Directory of Open Access Journals (Sweden)

    S. Alonso-Quesada

    2010-01-01

    Full Text Available This paper presents a strategy for designing a robust discrete-time adaptive controller for stabilizing linear time-invariant (LTI continuous-time dynamic systems. Such systems may be unstable and noninversely stable in the worst case. A reduced-order model is considered to design the adaptive controller. The control design is based on the discretization of the system with the use of a multirate sampling device with fast-sampled control signal. A suitable on-line adaptation of the multirate gains guarantees the stability of the inverse of the discretized estimated model, which is used to parameterize the adaptive controller. A dead zone is included in the parameters estimation algorithm for robustness purposes under the presence of unmodeled dynamics in the controlled dynamic system. The adaptive controller guarantees the boundedness of the system measured signal for all time. Some examples illustrate the efficacy of this control strategy.

  1. Developing Exon-Primed Intron-Crossing (EPIC) markers for population genetic studies in three Aedes disease vectors.

    Science.gov (United States)

    White, Vanessa Linley; Endersby, Nancy Margaret; Chan, Janice; Hoffmann, Ary Anthony; Weeks, Andrew Raymond

    2015-03-01

    Aedes aegypti, Aedes notoscriptus, and Aedes albopictus are important vectors of many arboviruses implicated in human disease such as dengue fever. Genetic markers applied across vector species can provide important information on population structure, gene flow, insecticide resistance, and taxonomy, however, robust microsatellite markers have proven difficult to develop in these species and mosquitoes generally. Here we consider the utility and transferability of 15 Ribosome protein (Rp) Exon-Primed Intron-Crossing (EPIC) markers for population genetic studies in these 3 Aedes species. Rp EPIC markers designed for Ae. aegypti also successfully amplified populations of the sister species, Ae. albopictus, as well as the distantly related species, Ae. notoscriptus. High SNP and good indel diversity in sequenced alleles plus support for amplification of the same regions across populations and species were additional benefits of these markers. These findings point to the general value of EPIC markers in mosquito population studies. © 2014 Institute of Zoology, Chinese Academy of Sciences.

  2. Variability of fish consumption within the 10 European countries participating in the European Investigation into Cancer and Nutrition (EPIC) study

    DEFF Research Database (Denmark)

    Welch, A.A.; Lund, E.; Amiano, P.

    2002-01-01

    OBJECTIVE: To describe and compare the consumption of total fish (marine foods) and the fish sub-groups - white fish, fatty fish, very fatty fish, fish products and crustacea, in participants from the European Investigation into Cancer and Nutrition (EPIC) study. DESIGN: Cross-sectional analysis...... of dietary intake using a computerised standardised 24-hour recall interview. Crude means, means and standard errors adjusted by age, season and day of the week were calculated, stratified by centre and gender. SETTING: Twenty-seven redefined centres in the 10 European countries participating in the EPIC...... study. SUBJECTS: In total, 35 955 subjects (13 031 men and 22 924 women), aged 35-74 years, selected from the main EPIC cohort. RESULTS: A six- to sevenfold variation in total fish consumption exists in women and men, between the lowest consumption in Germany and the highest in Spain. Overall, white...

  3. Pathology findings and validation of gastric and esophageal cancer cases in a European cohort (EPIC/EUR-GAST)

    DEFF Research Database (Denmark)

    Carneiro, F; Moutinho, C; Pera, G

    2007-01-01

    OBJECTIVE: Cardia, non-cardia and intestinal and diffuse subtypes of gastric cancer may have different trends and etiological factors. However, the available information is not always collected in population cancer registries, and heterogeneous criteria have been applied for the histopathological...... classification of tumors. We describe the pathological features of incident gastric and esophageal cancers identified within the European Prospective Investigation into Cancer and Nutrition (EPIC). MATERIAL AND METHODS: In an investigation on gastric and esophageal cancer (EUR-GAST) in the EPIC project......, a validation study of diagnoses reported by EPIC centers was conducted by a European panel of pathologists. Original pathology reports, stained slides of tumors and the respective paraffin blocks were requested from the centers. RESULTS: The whole series encompassed 467 cancer cases (gastric and esophageal...

  4. Coffee Drinking and Mortality in Ten European Countries – the EPIC Study

    Science.gov (United States)

    Gunter, Marc J.; Murphy, Neil; Cross, Amanda J.; Dossus, Laure; Dartois, Laureen; Fagherazzi, Guy; Kaaks, Rudolf; Kühn, Tilman; Boeing, Heiner; Aleksandrova, Krasimira; Tjønneland, Anne; Olsen, Anja; Overvad, Kim; Larsen, Sofus Christian; Cornejo, Maria Luisa Redondo; Agudo, Antonio; Pérez, María José Sánchez; Altzibar, Jone M; Navarro, Carmen; Ardanaz, Eva; Khaw, Kay-Tee; Butterworth, Adam; Bradbury, Kathryn E; Trichopoulou, Antonia; Lagiou, Pagona; Trichopoulos, Dimitrios; Palli, Domenico; Grioni, Sara; Vineis, Paolo; Panico, Salvatore; Tumino, Rosario; Bueno-de-Mesquita, Bas; Siersema, Peter; Leenders, Max; Beulens, Joline WJ; Uiterwaal, Cuno U; Wallström, Peter; Nilsson, Lena Maria; Landberg, Rikard; Weiderpass, Elisabete; Skeie, Guri; Braaten, Tonje; Brennan, Paul; Licaj, Idlir; Muller, David C; Sinha, Rashmi; Wareham, Nick; Riboli, Elio

    2018-01-01

    Background How coffee consumption relates to mortality in diverse European populations, with variable coffee preparation methods and customs, is unclear. Objectives To examine whether coffee consumption is associated with all-cause and cause-specific mortality in men and women. Design Prospective cohort study. Setting Ten European countries. Participants A total of 521,330 men and women enrolled in the European Prospective Investigation into Cancer and Nutrition (EPIC). Main outcome measure Multivariable hazard ratios (HRs) and 95% confidence intervals(CIs) estimated using multivariable Cox proportional hazards models. The association of coffee with serum biomarkers of liver function, inflammation, and metabolic health was evaluated in the EPIC Biomarkers sub-cohort (n=14,800). Results During a mean follow-up of 16.4 years, 41,693 deaths occurred. Compared with non-consumers, participants in the highest quartile of coffee consumption experienced statistically significant lower all-cause mortality (Men: HR=0.88, 95%CI: 0.82–0.95; P-trendcoffee and circulatory disease mortality, (HR=0.78, 95%CI: 0.68–0.90; P-trendcoffee and ovarian cancer mortality (HR 1.12, 95% CI: 1.02–1.23 P-trend 0.001). In the EPIC-biomarkers sub-cohort, higher coffee consumption was associated with lower serum alkaline phosphatase, alanine transaminase, aspartate transaminase, and C-reactive protein. Limitation Reverse causality may have led to spurious findings; however, results did not differ following exclusion of participants who died within 8-years of baseline. The study is also limited by a single assessment of coffee drinking habits at baseline. Conclusions These results confirm prior findings on the reduced risk of mortality associated with coffee drinking but additionally show that this relationship does not vary by country where coffee preparation and drinking habits may differ. The study also reports novel inverse relationships between coffee drinking and digestive disease

  5. Implementation of Epic Beaker Clinical Pathology at an academic medical center

    Directory of Open Access Journals (Sweden)

    Matthew D Krasowski

    2016-01-01

    Full Text Available Background: Epic Beaker Clinical Pathology (CP is a relatively new laboratory information system (LIS operating within the Epic suite of software applications. To date, there have not been any publications describing implementation of Beaker CP. In this report, we describe our experience in implementing Beaker CP version 2012 at a state academic medical center with a go-live of August 2014 and a subsequent upgrade to Beaker version 2014 in May 2015. The implementation of Beaker CP was concurrent with implementations of Epic modules for revenue cycle, patient scheduling, and patient registration. Methods: Our analysis covers approximately 3 years of time (2 years preimplementation of Beaker CP and roughly 1 year after using data summarized from pre- and post-implementation meetings, debriefings, and the closure document for the project. Results: We summarize positive aspects of, and key factors leading to, a successful implementation of Beaker CP. The early inclusion of subject matter experts in the design and validation of Beaker workflows was very helpful. Since Beaker CP does not directly interface with laboratory instrumentation, the clinical laboratories spent extensive preimplementation effort establishing middleware interfaces. Immediate challenges postimplementation included bar code scanning and nursing adaptation to Beaker CP specimen collection. The most substantial changes in laboratory workflow occurred with microbiology orders. This posed a considerable challenge with microbiology orders from the operating rooms and required intensive interventions in the weeks following go-live. In postimplementation surveys, pathology staff, informatics staff, and end-users expressed satisfaction with the new LIS. Conclusions: Beaker CP can serve as an effective LIS for an academic medical center. Careful planning and preparation aid the transition to this LIS.

  6. Estimation of Leaf Area Index and its Sunlit Portion from DSCOVR EPIC data

    Science.gov (United States)

    Knyazikhin, Y.; Yang, B.; Mottus, M.; Rautiainen, M.; Stenberg, P.; Yan, L.; Chen, C.; Yan, K.; Park, T.; Myneni, R. B.; Song, W.

    2016-12-01

    The NASA's Earth Polychromatic Imaging Camera (EPIC) onboard NOAA's Deep Space Climate Observatory (DSCOVR) mission was launched on February 11, 2015 to the Sun-Earth Lagrangian L1 point where it began to collect radiance data of the entire sunlit Earth at 16 km resolution (in equatorial zone) every 65 to 110 min in June 2015. It provides imageries in near backscattering directions with the scattering angle between 168o and 176o at ten UV to Near-IR narrow spectral bands centered at 317.5 (band width 1.0) nm, 325.0 (1.0) nm, 340.0 (3.0) nm, 388.0 (3.0) nm, 433.0 (3.0) nm, 551.0 (3.0) nm, 680.0 (1.7) nm, 687.8 (0.6) nm, 764.0 (1.7) nm and 779.5 (2.0) nm. This poster presents the theoretical basis of the algorithm designed for the generation of leaf area index (LAI) and diurnal course of sunlit leaf area index (SLAI) from EPIC Bidirectional Reflectance Factor of vegetated land. LAI and SLAI are defined as the total hemi-surface and sunlit leaf semi-surface per unit ground area. Whereas LAI is a standard product of many satellite the SLAI is a new satellite-derived parameter. Sunlit and shaded leaves exhibit different radiative response to incident Photosynthetically Active Radiation (400-700 nm), which in turn triggers various physiological and physical processes required for the functioning of plants. Leaf area and its sunlit portion are key state parameters in most ecosystem productivity and carbon/nitrogen cycle. Status of the EPIC LAI/SLAI product and its validation strategy are also discussed in this poster.

  7. Sabiduría epicúrea y Psicología

    Directory of Open Access Journals (Sweden)

    Vicente Pelechano

    2006-01-01

    Full Text Available Se presenta el marco teórico, la lógica de elaboración y primeros datos de validación de un cuestionario de sabiduría epicúrea (EPI-1 que ha sido cumplimentado por dos muestras de 473 y 266 adultos, con un predominio de mujeres. Además, se han cumplimentado el cuestionario NEO-PI-R de Costa y McCrae de los cinco grandes y dos escalas conectadas teóricamente con concepciones de sabiduría: una de prudencia y otra de intolerancia a la ambigüedad. Los resultados sugieren que, aunque sin una consistencia alta, se pueden rastrear en nuestros días los elementos básicos de la sabiduría epicúrea que se mezclan con otros de corte más funcional. Las relaciones con los cinco grandes así como con prudencia interpersonal e intolerancia de la ambigüedad demuestran que la sabiduría epicúrea no puede identificarse con ninguna de estas dimensiones, aunque guarda relaciones tenues con neuroticismo, apertura a la experiencia e intolerancia de la ambigüedad; asimismo se presenta como independiente de “prudencia” operacionalizada mediante refranes, que representa más bien estrategias de “supervivencia interpersonal”. Los resultados alcanzados se discuten dentro de un modelo de sabiduría alternativo al del grupo de Baltes en Berlín.

  8. Comparison of UHPLC and HPLC in benzodiazepines analysis of postmortem samples: a case-control study.

    Science.gov (United States)

    Behnoush, Behnam; Sheikhazadi, Ardeshir; Bazmi, Elham; Fattahi, Akbar; Sheikhazadi, Elham; Saberi Anary, Seyed Hossein

    2015-04-01

    The aim of this study was to compare system efficiency and analysis duration regarding the solvent consumption and system maintenance in high-pressure liquid chromatography (HPLC) and ultra high-pressure liquid chromatography (UHPLC). In a case-control study, standard solutions of 7 benzodiazepines (BZs) and 73 biological samples such as urine, tissue, stomach content, and bile that screened positive for BZs were analyzed by HPLC and UHPLC in laboratory of forensic toxicology during 2012 to 2013. HPLC analysis was performed using a Knauer by 100-5 C-18 column (250 mm × 4.6 mm) and Knauer photodiode array detector (PAD). UHPLC analysis was performed using Knauer PAD detector with cooling autosampler and Eurospher II 100-3 C-18 column (100 mm × 3 mm) and also 2 pumps. The mean retention time, standard deviation, flow rate, and repeatability of analytical results were compared by using 2 methods. Routine runtimes in HPLC and UHPLC took 40 and 15 minutes, respectively. Changes in mobile phase composition of the 2 methods were not required. Flow rate and solvent consumption in UHPLC decreased. Diazepam and flurazepam were detected more frequently in biological samples. In UHPLC, small particle size and short length of column cause effective separation of BZs in a very short time. Reduced flow rate, solvent consumption, and injection volume cause more efficiency and less analysis costs. Thus, in the detection of BZs, UHPLC is an accurate, sensitive, and fast method with less cost of analysis.

  9. EPIC 201585823, a rare triple-mode RR Lyrae star discovered in K2 mission data

    DEFF Research Database (Denmark)

    Kurtz, Donald W.; Bowman, Dominic M.; Ebo, Simon J.

    2016-01-01

    We have discovered a new, rare triple-mode RR Lyr star, EPIC 201585823, in the Kepler K2 mission Campaign 1 data. This star pulsates primarily in the fundamental and first-overtone radial modes, and, in addition, a third non-radial mode. The ratio of the period of the non-radial mode...... pixels with significant signal for the star, but without correction for pointing changes, is best for frequency analysis of this star, and, by implication, other RR Lyr stars observed by the K2 mission. We compare several pipeline reductions of the K2 mission data for this star....

  10. Diversity of dietary patterns observed in the European Prospective Investigation into Cancer and Nutrition (EPIC) project

    DEFF Research Database (Denmark)

    Slimani, N.; Fahey, M.; Welch, A.A.

    2002-01-01

    countries. France and particularly Spain have more heterogeneous dietary patterns, with a relatively high consumption of both plant foods and animal products. Apart from characteristics specific to vegetarian groups, the UK 'health-conscious' group shares with the UK general population a relatively high....../centres. In these countries, consumption of vegetables and fruit is similar to, or below, the overall EPIC means, and is low for legumes and vegetable oils. Overall, dietary patterns were similar for men and women, although there were large gender differences for certain food groups. CONCLUSIONS: There are considerable...

  11. Benefits of expressive writing in reducing test anxiety: A randomized controlled trial in Chinese samples.

    Science.gov (United States)

    Shen, Lujun; Yang, Lei; Zhang, Jing; Zhang, Meng

    2018-01-01

    To explore the effect of expressive writing of positive emotions on test anxiety among senior-high-school students. The Test Anxiety Scale (TAS) was used to assess the anxiety level of 200 senior-high-school students. Seventy-five students with high anxiety were recruited and divided randomly into experimental and control groups. Each day for 30 days, the experimental group engaged in 20 minutes of expressive writing of positive emotions, while the control group was asked to merely write down their daily events. A second test was given after the month-long experiment to analyze whether there had been a reduction in anxiety among the sample. Quantitative data was obtained from TAS scores. The NVivo10.0 software program was used to examine the frequency of particular word categories used in participants' writing manuscripts. Senior-high-school students indicated moderate to high test anxiety. There was a significant difference in post-test results (P 0.05). Students' writing manuscripts were mainly encoded on five code categories: cause, anxiety manifestation, positive emotion, insight and evaluation. There was a negative relation between positive emotion, insight codes and test anxiety. There were significant differences in the positive emotion, anxiety manifestation, and insight code categories between the first 10 days' manuscripts and the last 10 days' ones. Long-term expressive writing of positive emotions appears to help reduce test anxiety by using insight and positive emotion words for Chinese students. Efficient and effective intervention programs to ease test anxiety can be designed based on this study.

  12. Benefits of expressive writing in reducing test anxiety: A randomized controlled trial in Chinese samples.

    Directory of Open Access Journals (Sweden)

    Lujun Shen

    Full Text Available To explore the effect of expressive writing of positive emotions on test anxiety among senior-high-school students.The Test Anxiety Scale (TAS was used to assess the anxiety level of 200 senior-high-school students. Seventy-five students with high anxiety were recruited and divided randomly into experimental and control groups. Each day for 30 days, the experimental group engaged in 20 minutes of expressive writing of positive emotions, while the control group was asked to merely write down their daily events. A second test was given after the month-long experiment to analyze whether there had been a reduction in anxiety among the sample. Quantitative data was obtained from TAS scores. The NVivo10.0 software program was used to examine the frequency of particular word categories used in participants' writing manuscripts.Senior-high-school students indicated moderate to high test anxiety. There was a significant difference in post-test results (P 0.05. Students' writing manuscripts were mainly encoded on five code categories: cause, anxiety manifestation, positive emotion, insight and evaluation. There was a negative relation between positive emotion, insight codes and test anxiety. There were significant differences in the positive emotion, anxiety manifestation, and insight code categories between the first 10 days' manuscripts and the last 10 days' ones.Long-term expressive writing of positive emotions appears to help reduce test anxiety by using insight and positive emotion words for Chinese students. Efficient and effective intervention programs to ease test anxiety can be designed based on this study.

  13. Benefits of expressive writing in reducing test anxiety: A randomized controlled trial in Chinese samples

    Science.gov (United States)

    Zhang, Jing; Zhang, Meng

    2018-01-01

    Purpose To explore the effect of expressive writing of positive emotions on test anxiety among senior-high-school students. Methods The Test Anxiety Scale (TAS) was used to assess the anxiety level of 200 senior-high-school students. Seventy-five students with high anxiety were recruited and divided randomly into experimental and control groups. Each day for 30 days, the experimental group engaged in 20 minutes of expressive writing of positive emotions, while the control group was asked to merely write down their daily events. A second test was given after the month-long experiment to analyze whether there had been a reduction in anxiety among the sample. Quantitative data was obtained from TAS scores. The NVivo10.0 software program was used to examine the frequency of particular word categories used in participants’ writing manuscripts. Results Senior-high-school students indicated moderate to high test anxiety. There was a significant difference in post-test results (P 0.05). Students’ writing manuscripts were mainly encoded on five code categories: cause, anxiety manifestation, positive emotion, insight and evaluation. There was a negative relation between positive emotion, insight codes and test anxiety. There were significant differences in the positive emotion, anxiety manifestation, and insight code categories between the first 10 days’ manuscripts and the last 10 days’ ones. Conclusions Long-term expressive writing of positive emotions appears to help reduce test anxiety by using insight and positive emotion words for Chinese students. Efficient and effective intervention programs to ease test anxiety can be designed based on this study. PMID:29401473

  14. Feasibility of repeated 24-h dietary recalls combined with a food-recording booklet, using EPIC-Soft, among preschoolers

    DEFF Research Database (Denmark)

    Trolle, Ellen; Amiano, P.; Ege, Majken

    2011-01-01

    Background/Objectives:This study evaluates the feasibility among preschoolers of the 2 Ã 24-h dietary recalls (24-HDRs) method combined with a food-recording booklet (FRB), using EPIC-Soft pc-program for the 24-HDR (the software developed to conduct 24-HDRs in the European Prospective Investigation...... for a majority of the parents. In future studies, it may be beneficial to develop the FRB more like a structured food record (FR), which might, in principle, change the method to a one-day FR method from more than a 24-HDR method. It is recommended then to further investigate the use of EPIC-Soft as a data...

  15. Incorporation of a PbSe Array Based Spectrograph into EPICS using LabView at the JLab FEL Facility

    International Nuclear Information System (INIS)

    Hardy, D.; Benson, S.V.; Shinn, M.D.; Zhang, S.

    2005-01-01

    A real-time spectrograph with a 1Hz update rate was designed and installed at the JLab FEL facility using a Cal Sensors PbSe array and a Roper Scientific SpectraPro 300 monochrometer. This paper describes the implementation of EPICS channel access on a remote PC running LabView with modification of vendor supplied LabView VI's to allow display of FEL light spectra in real-time on a remote workstation. This allows PC based diagnostics to be used in EPICS

  16. Development of Multi-Sensor Global Cloud and Radiance Composites for DSCOVR EPIC Imager with Subpixel Definition

    Science.gov (United States)

    Khlopenkov, K. V.; Duda, D. P.; Thieman, M. M.; Sun-Mack, S.; Su, W.; Minnis, P.; Bedka, K. M.

    2017-12-01

    The Deep Space Climate Observatory (DSCOVR) is designed to study the daytime Earth radiation budget by means of onboard Earth Polychromatic Imaging Camera (EPIC) and National Institute of Standards and Technology Advanced Radiometer (NISTAR). EPIC imager observes in several shortwave bands (317-780 nm), while NISTAR measures the top-of-atmosphere (TOA) whole-disk radiance in shortwave and total broadband windows. Calculation of albedo and outgoing longwave flux requires a high-resolution scene identification such as the radiance observations and cloud property retrievals from low earth orbit and geostationary satellite imagers. These properties have to be co-located with EPIC imager pixels to provide scene identification and to select anisotropic directional models, which are then used to adjust the NISTAR-measured radiance and subsequently obtain the global daytime shortwave and longwave fluxes. This work presents an algorithm for optimal merging of selected radiances and cloud properties derived from multiple satellite imagers to obtain seamless global hourly composites at 5-km resolution. The highest quality observation is selected by means of an aggregated rating which incorporates several factors such as the nearest time relative to EPIC observation, lowest viewing zenith angle, and others. This process provides a smoother transition and avoids abrupt changes in the merged composite data. Higher spatial accuracy in the composite product is achieved by using the inverse mapping with gradient search during reprojection and bicubic interpolation for pixel resampling. The composite data are subsequently remapped into the EPIC-view domain by convolving composite pixels with the EPIC point spread function (PSF) defined with a half-pixel accuracy. Within every EPIC footprint, the PSF-weighted average radiances and cloud properties are computed for each cloud phase and then stored within five data subsets (clear-sky, water cloud, ice cloud, total cloud, and no

  17. The development of an automatic sample-changer and control instrumentation for isotope-source neutron-activation analysis

    International Nuclear Information System (INIS)

    Andeweg, A.H.; Watterson, J.I.W.

    1983-01-01

    An automatic sample-changer was developed at the Council for Mineral Technology for use in isotope-source neutron-activation analysis. Tests show that the sample-changer can transfer a sample of up to 3 kg in mass over a distance of 3 m within 5 s. In addition, instrumentation in the form of a three-stage sequential timer was developed to control the sequence of irradiation transfer and analysis

  18. Quality control in diagnostic molecular pathology in the Netherlands; proficiency testing for patient identification in tissue samples

    NARCIS (Netherlands)

    Thunnissen, F. B. J. M.; Tilanus, M. G. J.; Ligtenberg, M. J. L.; Nederlof, P. M.; Dinjens, W. N. M.; Meulemans, E.; van den Brule, A. J. C.; van Noesel, C. J. M.; de Leeuw, W. J. F.; Schuuring, E.

    2004-01-01

    Aims: To describe the evolution of proficiency testing for molecular diagnostic pathology with respect to determining unambiguously the patient identity of tissue samples by microsatellite analysis. Method: Four rounds of quality control exchanges of samples from different patients were sent with

  19. Output Information Based Fault-Tolerant Iterative Learning Control for Dual-Rate Sampling Process with Disturbances and Output Delay

    Directory of Open Access Journals (Sweden)

    Hongfeng Tao

    2018-01-01

    Full Text Available For a class of single-input single-output (SISO dual-rate sampling processes with disturbances and output delay, this paper presents a robust fault-tolerant iterative learning control algorithm based on output information. Firstly, the dual-rate sampling process with output delay is transformed into discrete system in state-space model form with slow sampling rate without time delay by using lifting technology; then output information based fault-tolerant iterative learning control scheme is designed and the control process is turned into an equivalent two-dimensional (2D repetitive process. Moreover, based on the repetitive process stability theory, the sufficient conditions for the stability of system and the design method of robust controller are given in terms of linear matrix inequalities (LMIs technique. Finally, the flow control simulations of two flow tanks in series demonstrate the feasibility and effectiveness of the proposed method.

  20. Method validation for control determination of mercury in fresh fish and shrimp samples by solid sampling thermal decomposition/amalgamation atomic absorption spectrometry.

    Science.gov (United States)

    Torres, Daiane Placido; Martins-Teixeira, Maristela Braga; Cadore, Solange; Queiroz, Helena Müller

    2015-01-01

    A method for the determination of total mercury in fresh fish and shrimp samples by solid sampling thermal decomposition/amalgamation atomic absorption spectrometry (TDA AAS) has been validated following international foodstuff protocols in order to fulfill the Brazilian National Residue Control Plan. The experimental parameters have been previously studied and optimized according to specific legislation on validation and inorganic contaminants in foodstuff. Linearity, sensitivity, specificity, detection and quantification limits, precision (repeatability and within-laboratory reproducibility), robustness as well as accuracy of the method have been evaluated. Linearity of response was satisfactory for the two range concentrations available on the TDA AAS equipment, between approximately 25.0 and 200.0 μg kg(-1) (square regression) and 250.0 and 2000.0 μg kg(-1) (linear regression) of mercury. The residues for both ranges were homoscedastic and independent, with normal distribution. Correlation coefficients obtained for these ranges were higher than 0.995. Limits of quantification (LOQ) and of detection of the method (LDM), based on signal standard deviation (SD) for a low-in-mercury sample, were 3.0 and 1.0 μg kg(-1), respectively. Repeatability of the method was better than 4%. Within-laboratory reproducibility achieved a relative SD better than 6%. Robustness of the current method was evaluated and pointed sample mass as a significant factor. Accuracy (assessed as the analyte recovery) was calculated on basis of the repeatability, and ranged from 89% to 99%. The obtained results showed the suitability of the present method for direct mercury measurement in fresh fish and shrimp samples and the importance of monitoring the analysis conditions for food control purposes. Additionally, the competence of this method was recognized by accreditation under the standard ISO/IEC 17025.

  1. The effects of parameter estimation on minimizing the in-control average sample size for the double sampling X bar chart

    Directory of Open Access Journals (Sweden)

    Michael B.C. Khoo

    2013-11-01

    Full Text Available The double sampling (DS X bar chart, one of the most widely-used charting methods, is superior for detecting small and moderate shifts in the process mean. In a right skewed run length distribution, the median run length (MRL provides a more credible representation of the central tendency than the average run length (ARL, as the mean is greater than the median. In this paper, therefore, MRL is used as the performance criterion instead of the traditional ARL. Generally, the performance of the DS X bar chart is investigated under the assumption of known process parameters. In practice, these parameters are usually estimated from an in-control reference Phase-I dataset. Since the performance of the DS X bar chart is significantly affected by estimation errors, we study the effects of parameter estimation on the MRL-based DS X bar chart when the in-control average sample size is minimised. This study reveals that more than 80 samples are required for the MRL-based DS X bar chart with estimated parameters to perform more favourably than the corresponding chart with known parameters.

  2. Slowing the Titanic: China's Epic Struggle with Tobacco.

    Science.gov (United States)

    Stone, Emily C A; Zhou, Caicun

    2016-12-01

    China is home to a third of the world's smokers and, correspondingly, to a third of the world's cases of lung cancer. Beginning in the mid-1990s, a generation or so later than in many Western countries, the Chinese government commenced measures to control tobacco, limiting advertising, banning smoking in many public venues, and increasing taxation. At the time of this review, there are signs that these policies are having some effect, but hundreds of millions of Chinese continue to smoke and rates of diagnosis of lung cancer continue to rise. There is much work to be done and much premature death to be suffered before the epidemic is slowed to the levels reached in Australia or the United States. This article aims to provide, particularly for practicing lung cancer clinicians, a description of patterns of smoking in China, the lung cancer epidemic there, and the stimuli for and barriers to tobacco control imposed by the highly complex and unique regulatory setting of the Chinese tobacco industry. A particular challenge in developing this description has come from the variability of studies published about a huge nation that has enormous diversity in wealth, education, urbanization, and tradition. The studies vary because the data vary. Much information on lung cancer and smoking rates in China comes, for example, from studies of cohorts that may number in the millions yet represent only a small percentage of the population and sometimes only a tiny geographic area of such a vast nation. National registry data on lung cancer in China do not yet cover even a fifth of the national population. Even so, we argue that several major trends can be identified: (1) more than 50% of men smoke regularly; (2) there are more than 300 million smokers in China; (3) almost half a million new cases of lung cancer are diagnosed in China each year; (4) secondhand smoking is a significant problem in China (as elsewhere), accounting for a high proportion of lung cancer cases among

  3. Feasible sampling plan for Bemisia tabaci control decision-making in watermelon fields.

    Science.gov (United States)

    Lima, Carlos Ho; Sarmento, Renato A; Pereira, Poliana S; Galdino, Tarcísio Vs; Santos, Fábio A; Silva, Joedna; Picanço, Marcelo C

    2017-11-01

    The silverleaf whitefly Bemisia tabaci is one of the most important pests of watermelon fields worldwide. Conventional sampling plans are the starting point for the generation of decision-making systems of integrated pest management programs. The aim of this study was to determine a conventional sampling plan for B. tabaci in watermelon fields. The optimal leaf for B. tabaci adult sampling was the 6 th most apical leaf. Direct counting was the best pest sampling technique. Crop pest densities fitted the negative binomial distribution and had a common aggregation parameter (K common ). The sampling plan consisted of evaluating 103 samples per plot. This sampling plan was conducted for 56 min, costing US$ 2.22 per sampling and with a 10% maximum evaluation error. The sampling plan determined in this study can be adopted by farmers because it enables the adequate evaluation of B. tabaci populations in watermelon fields (10% maximum evaluation error) and is a low-cost (US$ 2.22 per sampling), fast (56 min per sampling) and feasible (because it may be used in a standardized way throughout the crop cycle) technique. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  4. Job stress and locus of control in teachers: comparisons between samples from the United States and Zimbabwe

    Science.gov (United States)

    Crothers, Laura M.; Kanyongo, Gibbs Y.; Kolbert, Jered B.; Lipinski, John; Kachmar, Steven P.; Koch, Gary D.

    2010-12-01

    This study examines the relationship between educators' locus of control and job stress using samples from the US and Zimbabwe. Multiple regression analyses are used to identify significant relationships in the US sample between teachers' external locus of control and the severity of the job stress that they experience, coupled with the perceived degree of organisational support received. However, this relationship between the locus of control and stress indices could not be identified for the Zimbabwean sample. Significant differences between the two samples were noted in terms of educators' perceptions of the frequency of poor organisational support, with the Zimbabwean teachers reporting greater dissatisfaction. To explain these differences, a qualitative approach was utilised to illuminate the contextual stressors that educators face in Zimbabwe. The implications for teacher preparation measures are discussed.

  5. Electronic module for control of sample feeding device of spectrometers of X-ray fluorescent analysis of CRV type

    International Nuclear Information System (INIS)

    Petrov, V.A.; Fursov, A.V.

    2002-01-01

    The scheme of electronic module for sample feeding device control for the CRV type X-ray fluorescence analysis spectrometers is considered. This module provides realization of next functions: sample change operations and installation in starting position; signaling and defense at emergency cases; indication of any sample amount in the spectrometer chamber; testing function at tuning and testing of modules. All these principal functions are entrusted with microcontroller. Programming of the microcontroller is putting into effect by algorithm of the whole sample feeding device. In the capacity of microcontroller the single crystalline processor PICI16C54 and stepping motor of NV-306-V2202 model have been used

  6. Control of the positional relationship between a sample collection instrument and a surface to be analyzed during a sampling procedure using a laser sensor

    Science.gov (United States)

    Van Berkel, Gary J [Clinton, TN; Kertesz, Vilmos [Knoxville, TN

    2012-02-21

    A system and method utilizes distance-measuring equipment including a laser sensor for controlling the collection instrument-to-surface distance during a sample collection process for use, for example, with mass spectrometric detection. The laser sensor is arranged in a fixed positional relationship with the collection instrument, and a signal is generated by way of the laser sensor which corresponds to the actual distance between the laser sensor and the surface. The actual distance between the laser sensor and the surface is compared to a target distance between the laser sensor and the surface when the collection instrument is arranged at a desired distance from the surface for sample collecting purposes, and adjustments are made, if necessary, so that the actual distance approaches the target distance.

  7. The integration of two control systems

    International Nuclear Information System (INIS)

    Bickley, M.; White, K.

    1995-01-01

    During the past year the Continuous Electron Beam Accelerator Facility (CEBAF) has installed a new machine control system, based on the Experimental Physics and Industrial Control System (EPICS). The migration from CEBAF's old control system, Thaumaturgic Automated Control Logic (TACL), had to be done concurrently with commissioning of the CEBAF accelerator. The smooth transition to EPICS was made possible by the similarity of the control systems' topological design and network communication protocol. Both systems have operator display computer nodes which are decoupled from the data acquisition and control nodes. The communication between display and control nodes of both control systems is based on making named requests for data, with data being passed on change of value. Due to TACL's use of a central communications process, it was possible to integrate both control systems' network communications in that process. This in turn meant that CEBAF did not require changes to any other software in order to support network communication between TACL and EPICS. CEBAF implemented the machine's control under EPICS in an evolutionary, controlled manner. 4 refs., 3 figs

  8. Enabling Future Large Searches for Exoplanet Auroral Emission with the EPIC Correlator Architecture

    Science.gov (United States)

    Thyagarajan, Nithyanandan; Beardsley, Adam P.; Bowman, Judd D.; Morales, Miguel F.

    2017-05-01

    Extrasolar planets are expected to emit strong ``auroral'' emission at radio frequencies generated by the interaction of the host star's stellar winds with the planet's magnetosphere through electron-cyclotron maser emission. This transient emission lasts a few seconds to days and is almost fully circularly polarized. Detecting this emission in exoplanets is a critical probe of their magnetospheres and thus their interior compositions and habitability. The intensity and detectability of the emission depends on the suitability of many factors to the observing parameters such as the strength of the stellar wind power, the planetary magnetosphere cross-section, the highly beamed and coherent nature of electron-cyclotron emission, and narrow ranges of the planet's orbital phase. Large areas of sky must be surveyed continuously to high sensitivity to detect auroral emission. Next-generation radio telescopes with wide fields of view, large collecting areas and high efficiency are needed for these searches. This poses challenges to traditional correlator architectures whose computational cost scales as the square of the number of antennas. I will present a novel radio aperture synthesis imaging architecture - E-field Parallel Imaging Correlator (EPIC) - whose all-sky and full Stokes imaging capabilities will not only address the aforementioned factors preventing detection but also solve the computational challenges posed by large arrays. Compared to traditional imaging, EPIC is inherently fast and thus presents the unique advantage of probing transient timescales ranging orders of magnitude from tens of microseconds to days at no additional cost.

  9. An Analysis of Pulsating Subdwarf B Star EPIC 203948264 Observed During Campaign 2 of K2

    Directory of Open Access Journals (Sweden)

    Ketzer Laura

    2017-01-01

    Full Text Available We present a preliminary analysis of the newly–discovered pulsating subdwarf B (sdB star EPIC 203948264. The target was observed for 83 days in short cadence mode during Campaign 2 of K2, the two–gyro mission of the Kepler space telescope. A time–series analysis of the data revealed 22 independent pulsation frequencies in the g–mode region ranging from 100 to 600 μHz (0:5 to 2:8 hours. The main method we use to identify pulsation modes is asymptotic period spacing, and we were able to assign all but one of the pulsations to either l = 1 or l = 2. The average period spacings of both sequences are 261:34 ± 0.78 s and 151:18 ± 0.34 s, respectively. The pulsation amplitudes range from 0.77 ppt down to the detection limit at 0.212 ppt, and are not stable over the duration of the campaign. We detected one possible low–amplitude, l = 2, rotationally split multiplet, which allowed us to constrain the rotation period to 46 days or longer. This makes EPIC 203948264 another slowly rotating sdB star.

  10. Circulating RANKL and RANKL/OPG and Breast Cancer Risk by ER and PR Subtype: Results from the EPIC Cohort.

    Science.gov (United States)

    Sarink, Danja; Schock, Helena; Johnson, Theron; Overvad, Kim; Holm, Marianne; Tjønneland, Anne; Boutron-Ruault, Marie-Christine; His, Mathilde; Kvaskoff, Marina; Boeing, Heiner; Lagiou, Pagona; Papatesta, Eleni-Maria; Trichopoulou, Antonia; Palli, Domenico; Pala, Valeria; Mattiello, Amalia; Tumino, Rosario; Sacerdote, Carlotta; Bueno-de-Mesquita, H B As; van Gils, Carla H; Peeters, Petra H; Weiderpass, Elisabete; Agudo, Antonio; Sánchez, Maria-José; Chirlaque, Maria-Dolores; Ardanaz, Eva; Amiano, Pilar; Khaw, Kay Tee; Travis, Ruth; Dossus, Laure; Gunter, Mark; Rinaldi, Sabina; Merritt, Melissa; Riboli, Elio; Kaaks, Rudolf; Fortner, Renée T

    2017-09-01

    Receptor activator of nuclear factor-kappa B (RANK)-RANK ligand (RANKL) signaling promotes mammary tumor development in experimental models. Circulating concentrations of soluble RANKL (sRANKL) may influence breast cancer risk via activation of RANK signaling; this may be modulated by osteoprotegerin (OPG), the decoy receptor for RANKL. sRANKL and breast cancer risk by hormone receptor subtype has not previously been investigated. A case-control study was nested in the European Prospective Investigation into Cancer and Nutrition (EPIC) cohort. This study included 1,976 incident invasive breast cancer cases [estrogen receptor positive (ER+), n = 1,598], matched 1:1 to controls. Women were pre- or postmenopausal at blood collection. Serum sRANKL was quantified using an ELISA, serum OPG using an electrochemiluminescent assay. Risk ratios (RR) and 95% confidence intervals (95% CI) were calculated using conditional logistic regression. Associations between sRANKL and breast cancer risk differed by tumor hormone receptor status ( P het = 0.05). Higher concentrations of sRANKL were positively associated with risk of ER+ breast cancer [5th vs. 1st quintile RR 1.28 (95% CI, 1.01-1.63); P trend = 0.20], but not ER- disease. For both ER+ and estrogen and progesterone receptor positive (ER+PR+) breast cancer, results considering the sRANKL/OPG ratio were similar to those for sRANKL; we observed a suggestive inverse association between the ratio and ER-PR- disease [5th vs. 1st quintile RR = 0.60 (0.31-1.14); P trend = 0.03]. This study provides the first large-scale prospective data on circulating sRANKL and breast cancer. We observed limited evidence for an association between sRANKL and breast cancer risk. Cancer Prev Res; 10(9); 525-34. ©2017 AACR . ©2017 American Association for Cancer Research.

  11. Continuous quality control of the blood sampling procedure using a structured observation scheme.

    Science.gov (United States)

    Seemann, Tine Lindberg; Nybo, Mads

    2016-10-15

    An observational study was conducted using a structured observation scheme to assess compliance with the local phlebotomy guideline, to identify necessary focus items, and to investigate whether adherence to the phlebotomy guideline improved. The questionnaire from the EFLM Working Group for the Preanalytical Phase was adapted to local procedures. A pilot study of three months duration was conducted. Based on this, corrective actions were implemented and a follow-up study was conducted. All phlebotomists at the Department of Clinical Biochemistry and Pharmacology were observed. Three blood collections by each phlebotomist were observed at each session conducted at the phlebotomy ward and the hospital wards, respectively. Error frequencies were calculated for the phlebotomy ward and the hospital wards and for the two study phases. A total of 126 blood drawings by 39 phlebotomists were observed in the pilot study, while 84 blood drawings by 34 phlebotomists were observed in the follow-up study. In the pilot study, the three major error items were hand hygiene (42% error), mixing of samples (22%), and order of draw (21%). Minor significant differences were found between the two settings. After focus on the major aspects, the follow-up study showed significant improvement for all three items at both settings (P < 0.01, P < 0.01, and P = 0.01, respectively). Continuous quality control of the phlebotomy procedure revealed a number of items not conducted in compliance with the local phlebotomy guideline. It supported significant improvements in the adherence to the recommended phlebotomy procedures and facilitated documentation of the phlebotomy quality.

  12. A distributed timing system for synchronizing control and data correlation

    International Nuclear Information System (INIS)

    Stettler, M.; Thuot, M.; Dalesio, L.R.; Cole, R.; Fite, C.; Slentz, G.; Warren, D.

    1992-01-01

    Synchronization is necessary in experimental physics machines to provide positive control over related events. The Ground Test Accelerator (GTA) timing system provides this function through a distributed control system, known as the Experimental Physics and Industrial Control System (EPICS). The EPICS timing system was designed to take advantage of a distributed architecture, and provides time stamping for synchronous data correlation as well as event control. The system has been successfully demonstrated on over a dozen controller nodes for operation and data analysis. The design of the hardware, software, and operational results are discussed. (author). 2 refs., 4 figs

  13. A distributed timing system for sychronizing control and data correlation

    International Nuclear Information System (INIS)

    Stettler, M.; Thout, M.; Dalesio, L.R.; Cole, R.; Fite, C.; Slentz, G.; Warren, D.

    1992-01-01

    Synchronization is necessary in experimental physics machines to provide positive control over related events. The Ground Test Accelerator (GTA) timing system provides this function through a distributed control system, known as the Experimental Physics and Industrial Control System (EPICS). The EPICS timing system was designed to take advantage of a distributed architecture, and provides time stamping for synchronous data correlation as well as event control. The system has been successfully demonstrated on over a dozen controller nodes for operation and data analysis. The design of the hardware, software, and operational results are discussed

  14. Elpasolite Planetary Ice and Composition Spectrometer (EPICS): A Low-Resource Combined Gamma-Ray and Neutron Spectrometer for Planetary Science

    Science.gov (United States)

    Stonehill, L. C.; Coupland, D. D. S.; Dallmann, N. A.; Feldman, W. C.; Mesick, K.; Nowicki, S.; Storms, S.

    2017-12-01

    The Elpasolite Planetary Ice and Composition Spectrometer (EPICS) is an innovative, low-resource gamma-ray and neutron spectrometer for planetary science missions, enabled by new scintillator and photodetector technologies. Neutrons and gamma rays are produced by cosmic ray interactions with planetary bodies and their subsequent interactions with the near-surface materials produce distinctive energy spectra. Measuring these spectra reveals details of the planetary near-surface composition that are not accessible through any other phenomenology. EPICS will be the first planetary science instrument to fully integrate the neutron and gamma-ray spectrometers. This integration is enabled by the elpasolite family of scintillators that offer gamma-ray spectroscopy energy resolutions as good as 3% FWHM at 662 keV, thermal neutron sensitivity, and the ability to distinguish gamma-ray and neutron signals via pulse shape differences. This new detection technology will significantly reduce size, weight, and power (SWaP) while providing similar neutron performance and improved gamma energy resolution compared to previous scintillator instruments, and the ability to monitor the cosmic-ray source term. EPICS will detect scintillation light with silicon photomultipliers rather than traditional photomultiplier tubes, offering dramatic additional SWaP reduction. EPICS is under development with Los Alamos National Laboratory internal research and development funding. Here we report on the EPICS design, provide an update on the current status of the EPICS development, and discuss the expected sensitivity and performance of EPICS in several potential missions to airless bodies.

  15. Association of sleep duration with chronic diseases in the European Prospective Investigation into Cancer and Nutrition (EPIC-Potsdam study.

    Directory of Open Access Journals (Sweden)

    Anne von Ruesten

    Full Text Available BACKGROUND: In view of the reduced number of hours devoted to sleep in modern western societies the question arises what effects might result from sleep duration on occurrence of chronic diseases. METHODS: Data from 23 620 middle-aged participants of the European Prospective Investigation into Cancer and Nutrition (EPIC-Potsdam study, that were recruited between 1994-1998, were analyzed by using Cox proportional hazard regression to examine the association between self-reported sleep duration at baseline and incidence of chronic diseases, such as diabetes, myocardial infarction, stroke, and cancer. RESULTS: During a mean follow-up period of 7.8 years 841 incident cases of type 2 diabetes, 197 cases of myocardial infarction, 169 incident strokes, and 846 tumor cases were observed. Compared to persons sleeping 7-<8 h/day, participants with sleep duration of <6 h had a significantly increased risk of stroke (Hazard Ratio (HR = 2.06, 95% confidence interval (CI: 1.18-3.59, cancer (HR = 1.43, 95% CI: 1.09-1.87, and overall chronic diseases (HR = 1.31, 95% CI: 1.10-1.55 in multivariable adjusted models. Self-reported daytime sleep at baseline was not associated with incident chronic diseases in the overall study sample. However, there had been an effect modification of daytime sleep by hypertension showing that daytime sleep was inversely related to chronic disease risk among non-hypertensive participants but directly related to chronic diseases among hypertensives. CONCLUSION: Sleep duration of less than 6 h is a risky behavior for the development of chronic diseases, particularly stroke and cancer, and should be therefore addressed in public health campaigns.

  16. Association of sleep duration with chronic diseases in the European Prospective Investigation into Cancer and Nutrition (EPIC)-Potsdam study.

    Science.gov (United States)

    von Ruesten, Anne; Weikert, Cornelia; Fietze, Ingo; Boeing, Heiner

    2012-01-01

    In view of the reduced number of hours devoted to sleep in modern western societies the question arises what effects might result from sleep duration on occurrence of chronic diseases. Data from 23 620 middle-aged participants of the European Prospective Investigation into Cancer and Nutrition (EPIC)-Potsdam study, that were recruited between 1994-1998, were analyzed by using Cox proportional hazard regression to examine the association between self-reported sleep duration at baseline and incidence of chronic diseases, such as diabetes, myocardial infarction, stroke, and cancer. During a mean follow-up period of 7.8 years 841 incident cases of type 2 diabetes, 197 cases of myocardial infarction, 169 incident strokes, and 846 tumor cases were observed. Compared to persons sleeping 7-day, participants with sleep duration of <6 h had a significantly increased risk of stroke (Hazard Ratio (HR) = 2.06, 95% confidence interval (CI): 1.18-3.59), cancer (HR = 1.43, 95% CI: 1.09-1.87), and overall chronic diseases (HR = 1.31, 95% CI: 1.10-1.55) in multivariable adjusted models. Self-reported daytime sleep at baseline was not associated with incident chronic diseases in the overall study sample. However, there had been an effect modification of daytime sleep by hypertension showing that daytime sleep was inversely related to chronic disease risk among non-hypertensive participants but directly related to chronic diseases among hypertensives. Sleep duration of less than 6 h is a risky behavior for the development of chronic diseases, particularly stroke and cancer, and should be therefore addressed in public health campaigns.

  17. Analysis of methods commonly used in biomedicine for treatment versus control comparison of very small samples.

    Science.gov (United States)

    Ristić-Djurović, Jasna L; Ćirković, Saša; Mladenović, Pavle; Romčević, Nebojša; Trbovich, Alexander M

    2018-04-01

    A rough estimate indicated that use of samples of size not larger than ten is not uncommon in biomedical research and that many of such studies are limited to strong effects due to sample sizes smaller than six. For data collected from biomedical experiments it is also often unknown if mathematical requirements incorporated in the sample comparison methods are satisfied. Computer simulated experiments were used to examine performance of methods for qualitative sample comparison and its dependence on the effectiveness of exposure, effect intensity, distribution of studied parameter values in the population, and sample size. The Type I and Type II errors, their average, as well as the maximal errors were considered. The sample size 9 and the t-test method with p = 5% ensured error smaller than 5% even for weak effects. For sample sizes 6-8 the same method enabled detection of weak effects with errors smaller than 20%. If the sample sizes were 3-5, weak effects could not be detected with an acceptable error; however, the smallest maximal error in the most general case that includes weak effects is granted by the standard error of the mean method. The increase of sample size from 5 to 9 led to seven times more accurate detection of weak effects. Strong effects were detected regardless of the sample size and method used. The minimal recommended sample size for biomedical experiments is 9. Use of smaller sizes and the method of their comparison should be justified by the objective of the experiment. Copyright © 2018 Elsevier B.V. All rights reserved.

  18. The association between diet and obesity in specific European cohorts: DiOgenes and EPIC-PANACEA

    NARCIS (Netherlands)

    Feskens, E.J.M.; Sluik, D.; Huaidong, D.U.

    2014-01-01

    This review summarizes evidence from two projects embedded within the European Prospective Investigation into Cancer and Nutrition (EPIC) on the association between dietary factors and obesity risk, in particular change in weight and waist circumference. A total of 12 publications from DiOGenes and

  19. 75 FR 12230 - Black Oak Energy, L.L.C., EPIC Merchant Energy, LP, SESCO Enterprises, LLC v. PJM Interconnection...

    Science.gov (United States)

    2010-03-15

    ... Energy, L.L.C., EPIC Merchant Energy, LP, SESCO Enterprises, LLC v. PJM Interconnection, L.L.C.; Notice of Filing March 8, 2010. Take notice that on March 1, 2010, PJM Interconnection, L.L.C. filed a..., Order Accepting Compliance filing issued in this proceeding, Black Oak Energy, L.L.C., et al. v. PJM...

  20. “Nitrogen Budgets for the Mississippi River Basin using the linked EPIC-CMAQ-NEWS Models”

    Science.gov (United States)

    Presentation on the results from the 3 linked models, EPIC (USDA), CMAQ and NEWS to analyze a scenario of increased corn production related to biofuels together with Clean Air Act emission reductions across the US and the resultant effect on nitrogen loading to the Gulf of Mexico...

  1. The Experimental Projectile Impact Chamber (EPIC) at Centro de Astrobiología, Spain: Reproducibility and verification of scaling relations.

    Science.gov (United States)

    Ormö, J.; Wünnemann, K.; Collins, G.; Melero Asensio, I.

    2012-09-01

    The Experimental Projectile Impact Chamber (EPIC) consists of a 20.5mm caliber, compressed gas gun and a 7m wide test bed. It is possible to vary the projectile size and density, the velocity up to about 5001n/"s, the impact angle. and the target composition. The EPIC is especially designed for the analysis of impacts into unconsolidated and liquid targets. i.e. allowing the use of gravity scaling. The general objective with the EPIC is to analyze the cratering and modification processes at wet-target (e.g. marinle) impacts. We have carried out 14 shots into dry sand targets with two projectile compositions (light and weak; heavy and strong), at two impact angles. at three impact velocities, and in both quarter-space and half- space geometries. We recorded the impacts with a high-speed camera and compared the results with numerical simulations using iSALE. The evaluation demonstrated that there are noticeable differences between the results from the two projectile types, but that the crater dimensions are consistent with scaling laws based on other impact experiments [1]. This proves the usefulness of the EPIC in the analysis of natural impacts.

  2. The coal epic at Freyming-Merlebach; L'epopee du charbon a Freyming-Merlebach

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    This information document has been realized on the closure of the Merlebach site. It is devoted to the coal epic at Freyming-Merlebach. The historical aspects of the exploitation, the working conditions, the economic and environmental aspects of the mine and the today situation are detailed. (A.L.B.)

  3. Deferasirox in iron-overloaded patients with transfusion-dependent myelodysplastic syndromes: Results from the large 1-year EPIC study

    DEFF Research Database (Denmark)

    Gattermann, Norbert; Finelli, Carlo; Porta, Matteo Della

    2010-01-01

    The prospective 1-year EPIC study enrolled 341 patients with myelodysplastic syndromes (MDS); although baseline iron burden was >2500ng/mL, approximately 50% were chelation-naïve. Overall median serum ferritin decreased significantly at 1 year (p=0.002). Decreases occurred irrespective of whether...

  4. Polymorphisms of genes coding for ghrelin and its receptor in relation to anthropometry, circulating levels of IGF-I and IGFBP-3, and breast cancer risk : a case-control study nested within the European Prospective Investigation into Cancer and Nutrition (EPIC)

    NARCIS (Netherlands)

    Dossus, Laure; Mckay, James D.; Canzian, Federico; Wilkening, Stefan; Rinaldi, Sabina; Biessy, Carine; Olsen, Anja; Tjonneland, Anne; Jakobsen, Marianne U.; Overvad, Kim; Clavel-Chapelon, Francoise; Boutron-Ruault, Marie-Christine; Fournier, Agnes; Linseisen, Jakob; Lukanova, Annekatrin; Boeing, Heiner; Fisher, Eva; Trichopoulou, Antonia; Georgila, Christina; Trichopoulos, Dimitrios; Palli, Domenico; Krogh, Vittorio; Tumino, Rosario; Vineis, Paolo; Quiros, Jose Ramon; Sala, Nuria; Martinez-Garcia, Carmen; Dorronsoro, Miren; Chirlaque, Maria-Dolores; Barricarte, Aurelio; van Duijnhoven, Franzel J. B.; Bueno-de-Mesquita, H. B.; van Gils, Carla H.; Peeters, Petra H. M.; Hallmans, Goran; Lenner, Per; Bingham, Sheila; Khaw, Kay Tee; Key, Tim J.; Travis, Ruth C.; Ferrari, Pietro; Jenab, Mazda; Riboli, Elio; Kaaks, Rudolf

    Ghrelin, an endogenous ligand for the growth hormone secretagogue receptor, has two major functions: the stimulation of the growth hormone production and the stimulation of food intake. Accumulating evidence also suggests a role of ghrelin in cancer development. We conducted a case-control study on

  5. Economic Statistical Design of Variable Sampling Interval X¯$\\overline X $ Control Chart Based on Surrogate Variable Using Genetic Algorithms

    Directory of Open Access Journals (Sweden)

    Lee Tae-Hoon

    2016-12-01

    Full Text Available In many cases, a X¯$\\overline X $ control chart based on a performance variable is used in industrial fields. Typically, the control chart monitors the measurements of a performance variable itself. However, if the performance variable is too costly or impossible to measure, and a less expensive surrogate variable is available, the process may be more efficiently controlled using surrogate variables. In this paper, we present a model for the economic statistical design of a VSI (Variable Sampling Interval X¯$\\overline X $ control chart using a surrogate variable that is linearly correlated with the performance variable. We derive the total average profit model from an economic viewpoint and apply the model to a Very High Temperature Reactor (VHTR nuclear fuel measurement system and derive the optimal result using genetic algorithms. Compared with the control chart based on a performance variable, the proposed model gives a larger expected net income per unit of time in the long-run if the correlation between the performance variable and the surrogate variable is relatively high. The proposed model was confined to the sample mean control chart under the assumption that a single assignable cause occurs according to the Poisson process. However, the model may also be extended to other types of control charts using a single or multiple assignable cause assumptions such as VSS (Variable Sample Size X¯$\\overline X $ control chart, EWMA, CUSUM charts and so on.

  6. Selection bias in population-based cancer case-control studies due to incomplete sampling frame coverage.

    Science.gov (United States)

    Walsh, Matthew C; Trentham-Dietz, Amy; Gangnon, Ronald E; Nieto, F Javier; Newcomb, Polly A; Palta, Mari

    2012-06-01

    Increasing numbers of individuals are choosing to opt out of population-based sampling frames due to privacy concerns. This is especially a problem in the selection of controls for case-control studies, as the cases often arise from relatively complete population-based registries, whereas control selection requires a sampling frame. If opt out is also related to risk factors, bias can arise. We linked breast cancer cases who reported having a valid driver's license from the 2004-2008 Wisconsin women's health study (N = 2,988) with a master list of licensed drivers from the Wisconsin Department of Transportation (WDOT). This master list excludes Wisconsin drivers that requested their information not be sold by the state. Multivariate-adjusted selection probability ratios (SPR) were calculated to estimate potential bias when using this driver's license sampling frame to select controls. A total of 962 cases (32%) had opted out of the WDOT sampling frame. Cases age <40 (SPR = 0.90), income either unreported (SPR = 0.89) or greater than $50,000 (SPR = 0.94), lower parity (SPR = 0.96 per one-child decrease), and hormone use (SPR = 0.93) were significantly less likely to be covered by the WDOT sampling frame (α = 0.05 level). Our results indicate the potential for selection bias due to differential opt out between various demographic and behavioral subgroups of controls. As selection bias may differ by exposure and study base, the assessment of potential bias needs to be ongoing. SPRs can be used to predict the direction of bias when cases and controls stem from different sampling frames in population-based case-control studies.

  7. Sample sizes to control error estimates in determining soil bulk density in California forest soils

    Science.gov (United States)

    Youzhi Han; Jianwei Zhang; Kim G. Mattson; Weidong Zhang; Thomas A. Weber

    2016-01-01

    Characterizing forest soil properties with high variability is challenging, sometimes requiring large numbers of soil samples. Soil bulk density is a standard variable needed along with element concentrations to calculate nutrient pools. This study aimed to determine the optimal sample size, the number of observation (n), for predicting the soil bulk density with a...

  8. A rapid sample screening method for authenticity control of whiskey using capillary electrophoresis with online preconcentration.

    Science.gov (United States)

    Heller, Melina; Vitali, Luciano; Oliveira, Marcone Augusto Leal; Costa, Ana Carolina O; Micke, Gustavo Amadeu

    2011-07-13

    The present study aimed to develop a methodology using capillary electrophoresis for the determination of sinapaldehyde, syringaldehyde, coniferaldehyde, and vanillin in whiskey samples. The main objective was to obtain a screening method to differentiate authentic samples from seized samples suspected of being false using the phenolic aldehydes as chemical markers. The optimized background electrolyte was composed of 20 mmol L(-1) sodium tetraborate with 10% MeOH at pH 9.3. The study examined two kinds of sample stacking, using a long-end injection mode: normal sample stacking (NSM) and sample stacking with matrix removal (SWMR). In SWMR, the optimized injection time of the samples was 42 s (SWMR42); at this time, no matrix effects were observed. Values of r were >0.99 for the both methods. The LOD and LOQ were better than 100 and 330 mg mL(-1) for NSM and better than 22 and 73 mg L(-1) for SWMR. The CE-UV reliability in the aldehyde analysis in the real sample was compared statistically with LC-MS/MS methodology, and no significant differences were found, with a 95% confidence interval between the methodologies.

  9. Identification of control parameters for the sulfur gas storability with bag sampling methods

    Science.gov (United States)

    Air samples containing sulfur compounds are often collected and stored in sample bags prior to analyses. The storage stability of six gaseous sulfur compounds (H2S, CH3SH, DMS, CS2, DMDS and SO2) was compared between two different bag materials (polyvinyl fluoride (PVF) and polyester aluminum (PEA))...

  10. Commercial FPGA based multipurpose controller: implementation perspective

    International Nuclear Information System (INIS)

    Arredondo, I.; Campo, M. del; Echevarria, P.; Belver, D.; Muguira, L.; Garmendia, N.; Hassanzadegan, H.; Eguiraun, M.; Jugo, J.; Etxebarria, V.

    2012-01-01

    This work presents a fast acquisition multipurpose controller, focussing on its EPICS integration and on its XML based configuration. This controller is based on a Lyrtech VHS-ADC board which encloses an FPGA, connected to a Host PC. This Host acts as local controller and implements an IOC integrating the device in an EPICS network. These tasks have been performed using Java as the main tool to program the PC to make the device fit the desired application. All the process includes the use of different technologies: JNA to handle C functions i.e. FPGA API, JavaIOC to integrate EPICS and XML w3c DOM classes to easily configure the particular application. In order to manage the functions, Java specific tools have been developed: Methods to manage the FPGA (read/write registers, acquire data,...), methods to create and use the EPICS server (put, get, monitor,...), mathematical methods to process the data (numeric format conversions,...) and methods to create/ initialize the application structure by means of an XML file (parse elements, build the DOM and the specific application structure). This XML file has some common nodes and tags for all the applications: FPGA registers specifications definition and EPICS variables. This means that the user only has to include a node for the specific application and use the mentioned tools. A main class is in charge of managing the FPGA and EPICS server according to this XML file. This multipurpose controller has been successfully used to implement a BPM and an LLRF application for the ESS-Bilbao (European Spallation Source) facility. (authors)

  11. A separation theorem for the stochastic sampled-data LQG problem. [control of continuous linear plant disturbed by white noise

    Science.gov (United States)

    Halyo, N.; Caglayan, A. K.

    1976-01-01

    This paper considers the control of a continuous linear plant disturbed by white plant noise when the control is constrained to be a piecewise constant function of time; i.e. a stochastic sampled-data system. The cost function is the integral of quadratic error terms in the state and control, thus penalizing errors at every instant of time while the plant noise disturbs the system continuously. The problem is solved by reducing the constrained continuous problem to an unconstrained discrete one. It is shown that the separation principle for estimation and control still holds for this problem when the plant disturbance and measurement noise are Gaussian.

  12. Multiple category-lot quality assurance sampling: a new classification system with application to schistosomiasis control.

    Directory of Open Access Journals (Sweden)

    Casey Olives

    Full Text Available Originally a binary classifier, Lot Quality Assurance Sampling (LQAS has proven to be a useful tool for classification of the prevalence of Schistosoma mansoni into multiple categories (≤10%, >10 and <50%, ≥50%, and semi-curtailed sampling has been shown to effectively reduce the number of observations needed to reach a decision. To date the statistical underpinnings for Multiple Category-LQAS (MC-LQAS have not received full treatment. We explore the analytical properties of MC-LQAS, and validate its use for the classification of S. mansoni prevalence in multiple settings in East Africa.We outline MC-LQAS design principles and formulae for operating characteristic curves. In addition, we derive the average sample number for MC-LQAS when utilizing semi-curtailed sampling and introduce curtailed sampling in this setting. We also assess the performance of MC-LQAS designs with maximum sample sizes of n=15 and n=25 via a weighted kappa-statistic using S. mansoni data collected in 388 schools from four studies in East Africa.Overall performance of MC-LQAS classification was high (kappa-statistic of 0.87. In three of the studies, the kappa-statistic for a design with n=15 was greater than 0.75. In the fourth study, where these designs performed poorly (kappa-statistic less than 0.50, the majority of observations fell in regions where potential error is known to be high. Employment of semi-curtailed and curtailed sampling further reduced the sample size by as many as 0.5 and 3.5 observations per school, respectively, without increasing classification error.This work provides the needed analytics to understand the properties of MC-LQAS for assessing the prevalance of S. mansoni and shows that in most settings a sample size of 15 children provides a reliable classification of schools.

  13. Experimental control of calculation model of scale factor during fracture of circular samples with cracks

    International Nuclear Information System (INIS)

    Gnyp, I.P.; Ganulich, B.K.; Pokhmurskij, V.I.

    1982-01-01

    Reliable methods of estimation of cracking resistance of low-strength plastic materials using the notched samples acceptable for laboratory tests are analysed. Experimental data on the fracture of round notched samples for a number of steels are given. A perfect comparability of calculational and experimental data confirms the legitimacy of the proposed scheme of estimation of the scale factor effect. The necessity of taking into account the strain hardening coefficient at the choice of a sample size for determining the stress intensity factor is pointed out

  14. Chandra Reviews Black Hole Musical: Epic But Off-Key

    Science.gov (United States)

    2006-10-01

    give the strongest evidence to date of a shock wave produced by the supermassive black hole, a clear sign of a powerful explosion. This shock wave appears as a nearly circular ring of high-energy X-rays that is 85,000 light years in diameter and centered on the black hole. Other remarkable features are seen in M87 for the first time including narrow filaments of X-ray emission -- some over 100,000 light years long -- that may be due hot gas trapped by magnetic fields. Also, a large, previously unknown cavity in the hot gas, created by an outburst from the black hole about 70 million years ago, is seen in the X-ray image. Animation Showing a Supermassive Black Hole Outburst in M87 Animation Showing a Supermassive Black Hole Outburst in M87 "We can explain some of what we see, like the shock wave, with textbook physics," said team member Christine Jones, also of the CfA. "However, other details, like the filaments we find, leave us scratching our heads." Sound has been detected from another black hole in the Perseus cluster, which was calculated to have a note some 57 octaves below middle C. However, the sound in M87 appears to be more discordant and complex. A series of unevenly spaced loops in the hot gas gives evidence for small outbursts from the black hole about every 6 million years. These loops imply the presence of sound waves, not visible in the Chandra image, which are about 56 octaves below middle C. The presence of the large cavity and the sonic boom gives evidence for even deeper notes -- 58 or 59 octaves below middle C -- powered by large outbursts. These new results on M87 were presented at the High-Energy Astrophysics Division meeting being held in San Francisco. NASA's Marshall Space Flight Center, Huntsville, Ala., manages the Chandra program for the agency's Science Mission Directorate. The Smithsonian Astrophysical Observatory controls science and flight operations from the Chandra X-ray Center, Cambridge, Mass. Additional information and images are

  15. Efficient Photometry In-Frame Calibration (EPIC) Gaussian Corrections for Automated Background Normalization of Rate-Tracked Satellite Imagery

    Science.gov (United States)

    Griesbach, J.; Wetterer, C.; Sydney, P.; Gerber, J.

    Photometric processing of non-resolved Electro-Optical (EO) images has commonly required the use of dark and flat calibration frames that are obtained to correct for charge coupled device (CCD) dark (thermal) noise and CCD quantum efficiency/optical path vignetting effects respectively. It is necessary to account/calibrate for these effects so that the brightness of objects of interest (e.g. stars or resident space objects (RSOs)) may be measured in a consistent manner across the CCD field of view. Detected objects typically require further calibration using aperture photometry to compensate for sky background (shot noise). For this, annuluses are measured around each detected object whose contained pixels are used to estimate an average background level that is subtracted from the detected pixel measurements. In a new photometric calibration software tool developed for AFRL/RD, called Efficient Photometry In-Frame Calibration (EPIC), an automated background normalization technique is proposed that eliminates the requirement to capture dark and flat calibration images. The proposed technique simultaneously corrects for dark noise, shot noise, and CCD quantum efficiency/optical path vignetting effects. With this, a constant detection threshold may be applied for constant false alarm rate (CFAR) object detection without the need for aperture photometry corrections. The detected pixels may be simply summed (without further correction) for an accurate instrumental magnitude estimate. The noise distribution associated with each pixel is assumed to be sampled from a Poisson distribution. Since Poisson distributed data closely resembles Gaussian data for parameterized means greater than 10, the data may be corrected by applying bias subtraction and standard-deviation division. EPIC performs automated background normalization on rate-tracked satellite images using the following technique. A deck of approximately 50-100 images is combined by performing an independent median

  16. Sample Size Calculation: Inaccurate A Priori Assumptions for Nuisance Parameters Can Greatly Affect the Power of a Randomized Controlled Trial.

    Directory of Open Access Journals (Sweden)

    Elsa Tavernier

    Full Text Available We aimed to examine the extent to which inaccurate assumptions for nuisance parameters used to calculate sample size can affect the power of a randomized controlled trial (RCT. In a simulation study, we separately considered an RCT with continuous, dichotomous or time-to-event outcomes, with associated nuisance parameters of standard deviation, success rate in the control group and survival rate in the control group at some time point, respectively. For each type of outcome, we calculated a required sample size N for a hypothesized treatment effect, an assumed nuisance parameter and a nominal power of 80%. We then assumed a nuisance parameter associated with a relative error at the design stage. For each type of outcome, we randomly drew 10,000 relative errors of the associated nuisance parameter (from empirical distributions derived from a previously published review. Then, retro-fitting the sample size formula, we derived, for the pre-calculated sample size N, the real power of the RCT, taking into account the relative error for the nuisance parameter. In total, 23%, 0% and 18% of RCTs with continuous, binary and time-to-event outcomes, respectively, were underpowered (i.e., the real power was 90%. Even with proper calculation of sample size, a substantial number of trials are underpowered or overpowered because of imprecise knowledge of nuisance parameters. Such findings raise questions about how sample size for RCTs should be determined.

  17. COARSE: Convex Optimization based autonomous control for Asteroid Rendezvous and Sample Exploration, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Sample return missions, by nature, require high levels of spacecraft autonomy. Developments in hardware avionics have led to more capable real-time onboard computing...

  18. Stabilization of nonlinear systems using sampled-data output-feedback fuzzy controller based on polynomial-fuzzy-model-based control approach.

    Science.gov (United States)

    Lam, H K

    2012-02-01

    This paper investigates the stability of sampled-data output-feedback (SDOF) polynomial-fuzzy-model-based control systems. Representing the nonlinear plant using a polynomial fuzzy model, an SDOF fuzzy controller is proposed to perform the control process using the system output information. As only the system output is available for feedback compensation, it is more challenging for the controller design and system analysis compared to the full-state-feedback case. Furthermore, because of the sampling activity, the control signal is kept constant by the zero-order hold during the sampling period, which complicates the system dynamics and makes the stability analysis more difficult. In this paper, two cases of SDOF fuzzy controllers, which either share the same number of fuzzy rules or not, are considered. The system stability is investigated based on the Lyapunov stability theory using the sum-of-squares (SOS) approach. SOS-based stability conditions are obtained to guarantee the system stability and synthesize the SDOF fuzzy controller. Simulation examples are given to demonstrate the merits of the proposed SDOF fuzzy control approach.

  19. Preparation of quality control samples for its use in the radioimmunoassay de T3, T4 and TSH

    International Nuclear Information System (INIS)

    Lavalley E, C.; Delgado S, B.; Ruiz J, A.; Zambrano A, F.

    1991-09-01

    The use of quality control samples is necessary to evaluate, in a very simple way, the quality of the assays in the radioimmunoanalysis, since allows to settle down a quality control intra and inter analysis. In this work the methodology used for the preparation of these samples with low, media and high concentration for hormones related with the thyroid is shown, being obtained the following concentrations: 50, 200 and 500 ng/dl for T 3 ; 5.6, 7.8 and 14.4 μ g/dl for T 4 and 5.4, 13.4 and >50 μ U I/ml for TSH. (Author)

  20. Multiple category-lot quality assurance sampling: a new classification system with application to schistosomiasis control.

    Science.gov (United States)

    Olives, Casey; Valadez, Joseph J; Brooker, Simon J; Pagano, Marcello

    2012-01-01

    Originally a binary classifier, Lot Quality Assurance Sampling (LQAS) has proven to be a useful tool for classification of the prevalence of Schistosoma mansoni into multiple categories (≤10%, >10 and LQAS (MC-LQAS) have not received full treatment. We explore the analytical properties of MC-LQAS, and validate its use for the classification of S. mansoni prevalence in multiple settings in East Africa. We outline MC-LQAS design principles and formulae for operating characteristic curves. In addition, we derive the average sample number for MC-LQAS when utilizing semi-curtailed sampling and introduce curtailed sampling in this setting. We also assess the performance of MC-LQAS designs with maximum sample sizes of n=15 and n=25 via a weighted kappa-statistic using S. mansoni data collected in 388 schools from four studies in East Africa. Overall performance of MC-LQAS classification was high (kappa-statistic of 0.87). In three of the studies, the kappa-statistic for a design with n=15 was greater than 0.75. In the fourth study, where these designs performed poorly (kappa-statistic less than 0.50), the majority of observations fell in regions where potential error is known to be high. Employment of semi-curtailed and curtailed sampling further reduced the sample size by as many as 0.5 and 3.5 observations per school, respectively, without increasing classification error. This work provides the needed analytics to understand the properties of MC-LQAS for assessing the prevalance of S. mansoni and shows that in most settings a sample size of 15 children provides a reliable classification of schools.

  1. Polymorphisms of genes coding for ghrelin and its receptor in relation to anthropometry, circulating levels of IGF-I and IGFBP-3, and breast cancer risk: a case-control study nested within the European Prospective Investigation into Cancer and Nutrition (EPIC).

    Science.gov (United States)

    Dossus, Laure; McKay, James D; Canzian, Federico; Wilkening, Stefan; Rinaldi, Sabina; Biessy, Carine; Olsen, Anja; Tjønneland, Anne; Jakobsen, Marianne U; Overvad, Kim; Clavel-Chapelon, Françoise; Boutron-Ruault, Marie-Christine; Fournier, Agnes; Linseisen, Jakob; Lukanova, Annekatrin; Boeing, Heiner; Fisher, Eva; Trichopoulou, Antonia; Georgila, Christina; Trichopoulos, Dimitrios; Palli, Domenico; Krogh, Vittorio; Tumino, Rosario; Vineis, Paolo; Quirós, José Ramon; Sala, Núria; Martínez-García, Carmen; Dorronsoro, Miren; Chirlaque, Maria-Dolores; Barricarte, Aurelio; van Duijnhoven, Fränzel J B; Bueno-de-Mesquita, H B; van Gils, Carla H; Peeters, Petra H M; Hallmans, Göran; Lenner, Per; Bingham, Sheila; Khaw, Kay Tee; Key, Tim J; Travis, Ruth C; Ferrari, Pietro; Jenab, Mazda; Riboli, Elio; Kaaks, Rudolf

    2008-07-01

    Ghrelin, an endogenous ligand for the growth hormone secretagogue receptor, has two major functions: the stimulation of the growth hormone production and the stimulation of food intake. Accumulating evidence also suggests a role of ghrelin in cancer development. We conducted a case-control study on 1359 breast cancer cases and 2389 matched controls, nested within the European Prospective Investigation into Cancer and Nutrition, to examine the association of common genetic variants in the genes coding for ghrelin (GHRL) and its receptor (GHSR) with anthropometric measures, circulating insulin growth factor I (IGF-I) and insulin-like growth factor-binding protein 3 and breast cancer risk. Pair-wise tagging was used to select the 15 polymorphisms that represent the majority of common genetic variants across the GHRL and GHSR genes. A significant increase in breast cancer risk was observed in carriers of the GHRL rs171407-G allele (odds ratio: 1.2; 95% confidence interval: 1.0-1.4; P = 0.02). The GHRL single-nucleotide polymorphism rs375577 was associated with a 5% increase in IGF-I levels (P = 0.01). A number of GHRL and GHSR polymorphisms were associated with body mass index (BMI) and height (P between GHRL variations are associated with BMI. Furthermore, we have observed evidence for association of GHRL polymorphisms with circulating IGF-I levels and with breast cancer risk. These associations, however, might also be due to chance findings and further large studies are needed to confirm our results.

  2. Regional differences in infection control conditions in a sample of primary health care services in Brazil

    Directory of Open Access Journals (Sweden)

    Mauro Henrique Nogueira Guimarães de Abreu

    2017-11-01

    Full Text Available International guidelines have pointed out the importance of the physical environment of health care facilities in preventing and controlling infection. We aimed to describe the physical environment of dental care facilities in Brazil in 2014, focusing on characteristics designed to control infections. Exactly 16,202 dental offices in the Brazilian Unified National Health System (SUS participated in this survey. Trained researchers extracted information about the infection control characteristics of health facilities by using a structured instrument. We used data from 12 dichotomous questions that evaluated the wall, floor, sink and tap conditions, and the presence and condition of sterilization equipment. We calculated a score by summing the number of characteristics handled appropriately for infection control, which could range from 0 to 12. Hierarchical cluster analyses were developed. None of the 12 criteria were met by all the oral health teams. Only 208 (1.3% dental offices correctly performed all 12-infection control practices. Two clusters, with different frequencies of structure for infection control in dental offices, were identified. South and Southeast regions had the highest frequencies for Cluster 1, with better structure of infection control in dental offices. Dental care facilities of oral health teams were not typically meeting the infection control guidelines regarding clinic design and equipment. Adherence to the guidelines varied among the Brazilian geographic regions.

  3. Sample size calculation while controlling false discovery rate for differential expression analysis with RNA-sequencing experiments.

    Science.gov (United States)

    Bi, Ran; Liu, Peng

    2016-03-31

    RNA-Sequencing (RNA-seq) experiments have been popularly applied to transcriptome studies in recent years. Such experiments are still relatively costly. As a result, RNA-seq experiments often employ a small number of replicates. Power analysis and sample size calculation are challenging in the context of differential expression analysis with RNA-seq data. One challenge is that there are no closed-form formulae to calculate power for the popularly applied tests for differential expression analysis. In addition, false discovery rate (FDR), instead of family-wise type I error rate, is controlled for the multiple testing error in RNA-seq data analysis. So far, there are very few proposals on sample size calculation for RNA-seq experiments. In this paper, we propose a procedure for sample size calculation while controlling FDR for RNA-seq experimental design. Our procedure is based on the weighted linear model analysis facilitated by the voom method which has been shown to have competitive performance in terms of power and FDR control for RNA-seq differential expression analysis. We derive a method that approximates the average power across the differentially expressed genes, and then calculate the sample size to achieve a desired average power while controlling FDR. Simulation results demonstrate that the actual power of several popularly applied tests for differential expression is achieved and is close to the desired power for RNA-seq data with sample size calculated based on our method. Our proposed method provides an efficient algorithm to calculate sample size while controlling FDR for RNA-seq experimental design. We also provide an R package ssizeRNA that implements our proposed method and can be downloaded from the Comprehensive R Archive Network ( http://cran.r-project.org ).

  4. The Mediating Effect of Self-Control on Parenting and Delinquency: A Gendered Approach With a Multinational Sample.

    Science.gov (United States)

    Muftić, Lisa R; Updegrove, Alexander H

    2017-08-01

    This study aims to clarify the relationships between parenting techniques, low self-control, and juvenile delinquency in Gottfredson and Hirschi's general theory of crime while controlling for alternative explanations of delinquency. We relied on a sample of 35,511 adolescent students from 31 countries from the International Self-Report Delinquency 2 Study. Results indicate that parenting exhibits a direct effect on adolescents' violence perpetration and property offending, and that while self-control weakens the strength of this relationship, it fails to fully mediate it. Males reported lower levels of self-control, exposure to poorer parenting techniques, and higher rates of violence perpetration and property offending. The relationship between parenting, self-control, and juvenile delinquency was similar for females and males. These results provide evidence that parenting has important implications for adolescents' involvement in delinquency above and beyond its influence on their level of self-control.

  5. Sample size for post-marketing safety studies based on historical controls.

    Science.gov (United States)

    Wu, Yu-te; Makuch, Robert W

    2010-08-01

    As part of a drug's entire life cycle, post-marketing studies are an important part in the identification of rare, serious adverse events. Recently, the US Food and Drug Administration (FDA) has begun to implement new post-marketing safety mandates as a consequence of increased emphasis on safety. The purpose of this research is to provide exact sample size formula for the proposed hybrid design, based on a two-group cohort study with incorporation of historical external data. Exact sample size formula based on the Poisson distribution is developed, because the detection of rare events is our outcome of interest. Performance of exact method is compared to its approximate large-sample theory counterpart. The proposed hybrid design requires a smaller sample size compared to the standard, two-group prospective study design. In addition, the exact method reduces the number of subjects required in the treatment group by up to 30% compared to the approximate method for the study scenarios examined. The proposed hybrid design satisfies the advantages and rationale of the two-group design with smaller sample sizes generally required. 2010 John Wiley & Sons, Ltd.

  6. Differences in fungi present in induced sputum samples from asthma patients and non-atopic controls: a community based case control study

    Directory of Open Access Journals (Sweden)

    van Woerden Hugo Cornelis

    2013-02-01

    Full Text Available Abstract Background There is emerging evidence for the presence of an extensive microbiota in human lungs. It is not known whether variations in the prevalence of species of microbiota in the lungs may have aetiological significance in respiratory conditions such as asthma. The aim of the study was to undertake semi-quantitative analysis of the differences in fungal species in pooled sputum samples from asthma patients and controls. Methods Induced sputum samples were collected in a case control study of asthma patients and control subjects drawn from the community in Wandsworth, London. Samples from both groups were pooled and then tested for eukaryotes. DNA was amplified using standard PCR techniques, followed by pyrosequencing and comparison of reads to databases of known sequences to determine in a semi-quantitative way the percentage of DNA from known species in each of the two pooled samples. Results A total of 136 fungal species were identified in the induced sputum samples, with 90 species more common in asthma patients and 46 species more common in control subjects. Psathyrella candolleana, Malassezia pachydermatis, Termitomyces clypeatus and Grifola sordulenta showed a higher percentage of reads in the sputum of asthma patients and Eremothecium sinecaudum, Systenostrema alba, Cladosporium cladosporioides and Vanderwaltozyma polyspora showed a higher percentage of reads in the sputum of control subjects. A statistically significant difference in the pattern of fungi that were present in the respective samples was demonstrated using the Phylogenetic (P test (P  Conclusion This study is novel in providing evidence for the widespread nature of fungi in the sputum of healthy and asthmatic individuals. Differences in the pattern of fungi present in asthma patients and controls merit further investigation. Of particular interest was the presence of Malassezia pachydermatis, which is known to be associated with atopic dermatitis.

  7. EPIC 220204960

    DEFF Research Database (Denmark)

    Rappaport, S.; Vanderburg, A.; Borkovits, T.

    2017-01-01

    -star spectrum, which we designate as 'R-S' (red southerly image). With a 3.2-arcsec separation and similar radial velocities and photometric distances, 'B-N' is likely physically associated with 'R-S', making this a quintuple system, but that is incidental to our main claim of a strongly interacting quadruple...

  8. pH control and rapid mixing in spinning NMR samples

    Science.gov (United States)

    Yesinowski, James P.; Sunberg, Richard J.; Benedict, James J.

    An apparatus is described which permits the acquisition of NMR spectra from spinning 20-mm sample tubes while: (1) constantly monitoring the pH; (2) adding reagents to maintain constant pH (pH-statting); (3) efficiently mixing the added reagent. The apparatus was built to study the spontaneous precipitation of calcium phosphates from supersaturated solutions using 31P NMR. Other applications include the rapid determination of NMR titration curves, and the minimization of temperature gradients in large sample tubes. The apparatus was used to measure the 31P chemical shift titration of dilute phosphoric acid, which yielded accurate shifts for the three species of protonated orthophosphate ion. The bulk magnetic susceptibility of 85% H 3PO 4 relative to a dilute aqueous sample was also measured, and is shown to contribute significantly to chemical shift measurements.

  9. Recommended radiological air sampling and internal contamination control at nuclear power plants

    International Nuclear Information System (INIS)

    Rich, B.L.; Ritter, P.D.; Martz, D.E.

    1984-01-01

    It has long been recognized by the NRC Technical Staffs that estimating the quantity of radioactivity inhaled by an individual worker involved large uncertainties. General air samples usually produce concentrations lower than those in the workers Breathing Zone (BZ). NRC guides have recognized this problem by specifying air monitoring programs which sample the Breathing Zone or concentrations known to be higher than that actually inhaled. In addition the availability of suitable samplers to obtain BZ samples and the practicality of requiring their use was somewhat in question to the NRC technical staff. AN NRC development contract was issued to provide a detailed review of the technical aspects of the problems and recommendations for practical upgrade of federal guidance. This project accomplished a review of the nuclear industry experience and knowledge through a literature search, site visits to representative licensed facilities, telephone surveys of many others, laboratory testing of personal air samplers (lapel samplers) and aerosol diffusion experiments to verify key conclusions and assumptions

  10. The behaviour of fatigue-induced microdamage in compact bone samples from control and ovariectomised sheep.

    Science.gov (United States)

    Kennedy, Oran D; Brennan, Orlaith; Mauer, Peter; O'Brien, Fergal J; Rackard, Susan M; Taylor, David; Lee, T Clive

    2008-01-01

    This study investigates the effect of microdamage on bone quality in osteoporosis using an ovariectomised (OVX) sheep model of osteoporosis. Thirty-four sheep were divided into an OVX group (n=16) and a control group (n=18). Fluorochromes were administered intravenously at 3 monthly intervals after surgery to label bone turnover. After sacrifice, beams were removed from the metatarsal and tested in three-point bending. Following failure, microcracks were identified and quantified in terms of region, location and interaction with osteons. Number of cycles to failure (Nf) was lower in the OVX group relative to controls by approximately 7%. Crack density (CrDn) was higher in the OVX group compared to controls. CrDn was 2.5 and 3.5 times greater in the compressive region compared to tensile in control and OVX bone respectively. Combined results from both groups showed that 91% of cracks remained in interstitial bone, approximately 8% of cracks penetrated unlabelled osteons and less than 1% penetrated into labelled osteons. All cases of labelled osteon penetration occurred in controls. Crack surface density (CrSDn), was 25% higher in the control group compared to OVX. It is known that crack behaviour on meeting microstructural features such as osteons will depend on crack length. We have shown that osteon age also affects crack propagation. Long cracks penetrated unlabelled osteons but not labelled ones. Some cracks in the control group did penetrate labelled osteons. This may be due the fact that control bone is more highly mineralized. CrSDn was increased by 25% in the control group compared to OVX. Further study of these fracture mechanisms will help determine the effect of microdamage on bone quality and how this contributes to bone fragility.

  11. EPICS V4 expands support to physics application, data acquisition, and data analysis

    International Nuclear Information System (INIS)

    Dalesio, L.; Carcassi, G.; Kraimer, M.R.; Malitsky, N.; Shen, G.; Davidsaver, M.; Lange, R.; Sekoranja, M.; Rowland, J.; White, G.; Korhonen, T.

    2012-01-01

    EPICS version 4 extends the functionality of version 3 by providing the ability to define, transport, and introspect composite data types. Version 3 provided a set of process variables and a data protocol that adequately defined scalar data along with an atomic set of attributes. While remaining backward compatible, Version 4 is able to easily expand this set with a data protocol capable of exchanging complex data types and parameterized data requests. Additionally, a group of engineers defined reference types for some applications in this environment. The goal of this work is to define a narrow interface with the minimal set of data types needed to support a distributed architecture for physics applications, data acquisition, and data analysis. (authors)

  12. Cultural Trauma and Christian Identity in the Late Medieval Heroic Epic, The Siege of Jerusalem.

    Science.gov (United States)

    DeMarco, Patricia A

    2015-01-01

    This essay examines scenes of violence in the late medieval poem The Siege of Jerusalem in order to reveal the ways in which trauma is used as the grounds upon which Christian/Jewish difference is established. In particular, I argue that this poem serves as an example of a widespread element in Christian chivalric identity, namely the need to manage the repetitive invocation of Christ's crucifixion (ritually repeated through liturgical and poetic invocation) as a means of asserting both the bodily and psychic integrity of the Christian subject in contrast to the violently abjected figure of the Jewish body. The failure of The Siege protagonist, Wespasian, to navigate the cultural trauma of the crucifixion is contrasted to the successful management of trauma by the martial hero, Tancred, in Tasso's epic, Gerusalemme Liberata, illustrating the range of imaginative possibilities for understanding trauma in pre-modern war literature.

  13. Average energetic ion flux variations associated with geomagnetic activity from EPIC/STICS on Geotail

    Science.gov (United States)

    Christon, S. P.; Gloeckler, G.; Eastman, T. E.; McEntire, R. W.; Roelef, E. C.; Lui, A. T. Y.; Williams, D. J.; Frank, L. A.; Paterson, W. R.; Kokubun, S.; hide

    1996-01-01

    The magnetotail ion flux measurements from the Geotail spacecraft are analyzed both with and without the application of selection criteria that identify the plasma regime in which an observation is obtained. The different results are compared with each other. The initial results on the changes of energetic ion flux and composition correlated to average substorm activity in different magnetotail plasma regimes are discussed. The energetic ions are measured using the energetic particles and ion composition (EPIC) experiment and the suprathermal ion composition spectrometer (STICS). The plasma, wave and field instruments of the Geotail satellite were used to identify the principle magnetotail plasma regimes of plasma sheet, lobe, and magnetospheric boundary layer, as well as the magnetosheath and solar wind. Energetic O and H ions were observed in all the plasma regimes.

  14. Relationship between eating styles and temperament in an Anorexia Nervosa, Healtlhy Control, and Morbid Obesity female sample.

    NARCIS (Netherlands)

    Banos, R.M.; Cebolla, A.; Moragrega, I.; van Strien, T.; Fernandez-Aranda, F.; Aguera, Z.; de la Torre, R.; Casanueva, F.F.; Fernandez-Real, J.M.; Fernandez-Garcia, J.C.; Fruhbeck, G.; Gomez-Ambrosi, J.; Jimenez-Murcia, S.; Rodriquez, R.; Tinahones, F.J.; Botella, C.

    2014-01-01

    Objectives: Eating styles have been studied in both Obesity (OB) and Eating Disorders (ED), but they have not been examined in these two weight conditions together. The present study explores differences in eating styles in an Anorexia Nervosa (AN) and OB sample, compared to Healthy Controls (HC),

  15. Association analysis of ANK3 gene variants in nordic bipolar disorder and schizophrenia case-control samples

    DEFF Research Database (Denmark)

    Tesli, Martin; Koefoed, Pernille; Athanasiu, Lavinia

    2011-01-01

    Genetic variants in ankyrin 3 (ANK3) have recently been shown to be associated with bipolar disorder (BD). We genotyped three ANK3 SNPs previously found to be associated with BD (rs10994336, rs1938526, and rs9804190) in a Scandinavian BD case–control sample (N¿=¿854/2,614). Due to evidence...

  16. What Is the Best Blood Sampling Time for Metabolic Control of Phenylalanine and Tyrosine Concentrations in Tyrosinemia Type 1 Patients?

    NARCIS (Netherlands)

    van Dam, Esther; Daly, Anne; Venema-Liefaard, Gineke; van Rijn, Margreet; Derks, Terry G J; McKiernan, Patrick J; Heiner-Fokkema, Rebecca; MacDonald, Anita; van Spronsen, Francjan J

    2017-01-01

    BACKGROUND: Treatment of hereditary tyrosinemia type 1 with nitisinone and phenylalanine and tyrosine restricted diet has largely improved outcome, but the best blood sampling time for assessment of metabolic control is not known. AIM: To study diurnal and day-to-day variation of phenylalanine and

  17. Turbidity-controlled suspended sediment sampling for runoff-event load estimation

    Science.gov (United States)

    Jack Lewis

    1996-01-01

    Abstract - For estimating suspended sediment concentration (SSC) in rivers, turbidity is generally a much better predictor than water discharge. Although it is now possible to collect continuous turbidity data even at remote sites, sediment sampling and load estimation are still conventionally based on discharge. With frequent calibration the relation of turbidity to...

  18. Controlled dehydration of a biological sample using an alternative form of environmental SEM

    Czech Academy of Sciences Publication Activity Database

    Neděla, Vilém

    2010-01-01

    Roč. 237, č. 1 (2010), s. 7-11 ISSN 0022-2720 Institutional research plan: CEZ:AV0Z20650511 Keywords : biological sample * dehydration * environmental SEM * AQUASEM II * hydration system Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.872, year: 2010

  19. Determination of Technetium-99 in Environmental Samples by Solvent Extraction at Controlled Valence

    DEFF Research Database (Denmark)

    Chen, Q.J.; Aarkrog, A.; Dahlgaard, H.

    1989-01-01

    Distribution coefficients of technetium and ruthenium are determined under different conditions with CCl4, cyclohexanone, and 5% tri-isooctylamine (TIOA)/xylene. A method for analyzing 99Tc in environmental samples has been developed by solvent extraction in which the valences of technetium...

  20. Time trends in cigarette smoking in two German cohorts--results from EPIC Germany.

    Science.gov (United States)

    Rohrmann, S; Kroke, A; Boeing, H; Becker, N

    2003-08-01

    Smoking prevention is less advanced in Germany compared with other European and North American countries, and fewer data exist, especially on the consumption habits at the individual level over time. EPIC Germany, which is part of a European multicentre study on diet and cancer, collected data on individual smoking behaviour and allows for consideration of the changing consumption pattern for both centres and different age groups. Within EPIC 25 546 and 27 548 participants, respectively, were recruited in Heidelberg and Potsdam. Data on smoking habits were collected by means of a computer-guided interview during the baseline examination between 1994 and 1998. For each birth cohort smoking prevalence and mean number of cigarettes smoked per day at different ages were calculated. Additionally, the prevalence of non-filter cigarette smoking was computed. Smoking prevalence in the 1990s was still higher among men (Heidelberg 16.3-32.3%; Potsdam 18.2-29.3%) than among women (Heidelberg 12.8-32.0%; Potsdam 10.4-27.8%). However, the percentage of women smokers was still increasing. Filter cigarettes comprised a growing percentage of the cigarettes smoked, but especially among men differences between both German cohorts can still be seen: depending on age, 10.0-12.7% of men in the Heidelberg cohort smoked non-filter cigarettes, but only 1.1-2.3% in the Potsdam cohort. The quantity smoked was higher in the Heidelberg than in the Potsdam cohort with respect to the mean number of cigarettes smoked per day as well as the pack-years of smoking. In conclusion, smoking habits in the Potsdam and the Heidelberg cohorts did not strongly differ by smoking prevalence. However, they did differ according to the quantity and quality of smoking. These differences, as well as the changes over the last 40 years may contribute to a changing pattern of diseases in different groups of the German population.

  1. Implementation of epic beaker anatomic pathology at an academic medical center

    Directory of Open Access Journals (Sweden)

    John Larry Blau

    2017-01-01

    Full Text Available Background: Beaker is a relatively new laboratory information system (LIS offered by Epic Systems Corporation as part of its suite of health-care software and bundled with its electronic medical record, EpicCare. It is divided into two modules, Beaker anatomic pathology (Beaker AP and Beaker Clinical Pathology. In this report, we describe our experience implementing Beaker AP version 2014 at an academic medical center with a go-live date of October 2015. Methods: This report covers preimplementation preparations and challenges beginning in September 2014, issues discovered soon after go-live in October 2015, and some post go-live optimizations using data from meetings, debriefings, and the project closure document. Results: We share specific issues that we encountered during implementation, including difficulties with the proposed frozen section workflow, developing a shared specimen source dictionary, and implementation of the standard Beaker workflow in large institution with trainees. We share specific strategies that we used to overcome these issues for a successful Beaker AP implementation. Several areas of the laboratory-required adaptation of the default Beaker build parameters to meet the needs of the workflow in a busy academic medical center. In a few areas, our laboratory was unable to use the Beaker functionality to support our workflow, and we have continued to use paper or have altered our workflow. In spite of several difficulties that required creative solutions before go-live, the implementation has been successful based on satisfaction surveys completed by pathologists and others who use the software. However, optimization of Beaker workflows has continued to be an ongoing process after go-live to the present time. Conclusions: The Beaker AP LIS can be successfully implemented at an academic medical center but requires significant forethought, creative adaptation, and continued shared management of the ongoing product by

  2. El estudio prospectivo europeo sobre cáncer y nutrición (EPIC

    Directory of Open Access Journals (Sweden)

    Carlos A. González

    2004-01-01

    Full Text Available EPIC es un estudio prospectivo multicéntrico coordinado por la Agencia Internacional de Investigación del Cancer (IARC de la OMS, que se inició en 1993 con la recogida de datos y muestras de sangre en 23 centros de 10 países europeos: Alemania, Dinamarca, España, Francia, Grecia, Holanda, Italia, Noruega, Reino Unido y Suecia, En España se realiza en 5 áreas geográficas: Asturias, Granada, Guipúzcoa, Murcia y Navarra. Se incluyeron en la cohorte 519.978 individuos (de los cuales 366.521 son mujeres y en 385.719 de ellos se dispone de muestras de sangre por análisis de laboratorio. Hasta la fecha se han identificado 24.195 casos incidentes de cáncer. Los resultados de la comparación del consumo alimentario entre los 23 centros europeos se han publicado en el 2002, en un suplemento de una revista europea de Nutrición. Los primeros resultados obtenidos en EPIC sobre la relación de la dieta y el cáncer muestran un efecto protector del consumo de fibras, frutas y verduras sobre el cáncer colo-rectal, un efecto protector del consumo de frutas sobre el cáncer de pulmón, y de las frutas y verduras sobre el tracto digestivo superior, mientras que se ha confirmado que el alto consumo de frutas y verduras no tiene efecto sobre el cáncer de próstata. Usando un diario de 7 días para evaluar el consumo de grasas saturadas, se ha confirmado que un alto consumo de estas aumenta el riesgo de cáncer de mama.

  3. Overweight, obesity and fat distribution in 50- to 64-year-old participants in the European Prospective Investigation into Cancer and Nutrition (EPIC)

    NARCIS (Netherlands)

    Haftenberger, M; Lahmann, P.H.; Panico, S; Gonzalez-Martinez, A.C.; Seidell, J. C.; Boeing, H; Giurdanella, M C; Krogh, V.; Bueno De Mesquita, H Bas; Peeters, Petra H M; Skeie, G.; Hjartåker, A; Rodriguez, M.; Quirós, J. R.; Berglund, G.; Janlert, U; Khaw, K.T.; Spencer, E.A.; Overvad, K.; Tjønneland, A; Clavel-Chapelon, F.; Tehard, B; Miller, A.B.; Klipstein-Grobusch, K; Benetou, V.; Kiriazi, G; Riboli, E.; Slimani, N.

    2002-01-01

    Objective: To describe anthropometric characteristics of participants of the European Prospective Investigation into Cancer and Nutrition (EPIC). Design: A cross-sectional analysis of baseline data of a European prospective cohort study. Subjects: This analysis includes study populations from 25

  4. Evolutionary Process for Integrating COTS-Based Systems (EPIC): An Overview. Key Elements in Building, Fielding, and Supporting Commercial-off-the-Shelf (COTS) Based Solutions

    National Research Council Canada - National Science Library

    Albert, Cecilia

    2002-01-01

    .... The Evolutionary Process for Integrating COTS-based systems (EPIC) redefines acquisition, management, and engineering practices to more effectively leverage the COTS marketplace and other sources of pre-existing components...

  5. Comparison of Address-based Sampling and Random-digit Dialing Methods for Recruiting Young Men as Controls in a Case-Control Study of Testicular Cancer Susceptibility

    OpenAIRE

    Clagett, Bartholt; Nathanson, Katherine L.; Ciosek, Stephanie L.; McDermoth, Monique; Vaughn, David J.; Mitra, Nandita; Weiss, Andrew; Martonik, Rachel; Kanetsky, Peter A.

    2013-01-01

    Random-digit dialing (RDD) using landline telephone numbers is the historical gold standard for control recruitment in population-based epidemiologic research. However, increasing cell-phone usage and diminishing response rates suggest that the effectiveness of RDD in recruiting a random sample of the general population, particularly for younger target populations, is decreasing. In this study, we compared landline RDD with alternative methods of control recruitment, including RDD using cell-...

  6. The evolution of Jefferson Lab's control system

    International Nuclear Information System (INIS)

    K. S. White; M. Bickley; W. Watson

    1999-01-01

    Thomas Jefferson National Accelerator Facility's (Jefferson Lab) accelerator controls were initially implemented as a proprietary in-house system. During machine commissioning, problems were encountered leading to a decision to migrate to the Experimental Physics and Industrial Controls System (EPICS). Since then, the accelerator and all other laboratory controls have been successfully converted. In addition to implementing Jefferson Lab's controls using EPICS, new data visualization tools have been developed and existing programs have been enhanced with new capabilities. In order to provide a more generic interface for high level applications development, a device abstraction layer, called Common DEVice (CDEV), was implemented. These additions have been made available to other laboratories and are in use at many sites, including some that do not use EPICS. Control System development is not limited to computer scientists; operators, engineers and physicists frequently add capabilities using EPICS, CDEV, Tel/tk, and other tools. These contributions have tailored the control system for many different types of customers. For the future, the authors envision more intelligent processing and more capable tools for data storage, retrieval and visualization

  7. THE PLOT OF HUSBAND’S RETURN TO HIS WIFE’S WEDDING IN "THE ODYSSEY" BY HOMER AND IN THE SLAVIC AND RUSSIAN EPIC

    Directory of Open Access Journals (Sweden)

    Tatyana G. Malchukova

    2015-11-01

    Full Text Available The article analyzes the plot of husband’s return to his wife’s wedding embodied both in the millenary Ancient epic literature represented by the "Odyssey" of Homer, and in the Russian and Slavic epic. The study of Homer’s epic heritage, conducted over the years, includes a huge number of works of scientists around the world. Comparative-historical, comparative-genetic and comparative-typological studies found a link between oral folk tradition and epic poetry written by an author. The current international science is developing the hypothesis that professionally individual Homeric poems, which are at least 850 years old, were created in the ancient, oral poetry improvisation in a precise format of hexameter. The study of the Russian epic has less history, but the researches in this field have revealed the presence of Late Antiquity elements in the Slavic environment. These elements along with paganism and Christianity became the source of the people’s spiritual culture. The plot "the return of her husband", which is analyzed in the article, is widely-spread in folklore of many nations, and appeared rudimentarily in "The Odyssey". The western and eastern variants of this theme are diverse in genre structure and stylistic features. In Russian tradition the plot is presented in a large thematic variety "Dobrynya and Alyosha", which evolves into the epic genre due to contamination, small inserts in the epic genre. As a result, the great volume brings together the olden time and the ancient epic, creating intermediate forms comparable with the author’s imitations.

  8. Enhancing the Frequency Adaptability of Periodic Current Controllers with a Fixed Sampling Rate for Grid-Connected Power Converters

    DEFF Research Database (Denmark)

    Yang, Yongheng; Zhou, Keliang; Blaabjerg, Frede

    2016-01-01

    Grid-connected power converters should employ advanced current controllers, e.g., Proportional Resonant (PR) and Repetitive Controllers (RC), in order to produce high-quality feed-in currents that are required to be synchronized with the grid. The synchronization is actually to detect...... of the resonant controllers and by approximating the fractional delay using a Lagrange interpolating polynomial for the RC, respectively, the frequency-variation-immunity of these periodic current controllers with a fixed sampling rate is improved. Experiments on a single-phase grid-connected system are presented...... the instantaneous grid information (e.g., frequency and phase of the grid voltage) for the current control, which is commonly performed by a Phase-Locked-Loop (PLL) system. Hence, harmonics and deviations in the estimated frequency by the PLL could lead to current tracking performance degradation, especially...

  9. Random Photon Absorption Model Elucidates How Early Gain Control in Fly Photoreceptors Arises from Quantal Sampling

    Science.gov (United States)

    Song, Zhuoyi; Zhou, Yu; Juusola, Mikko

    2016-01-01

    Many diurnal photoreceptors encode vast real-world light changes effectively, but how this performance originates from photon sampling is unclear. A 4-module biophysically-realistic fly photoreceptor model, in which information capture is limited by the number of its sampling units (microvilli) and their photon-hit recovery time (refractoriness), can accurately simulate real recordings and their information content. However, sublinear summation in quantum bump production (quantum-gain-nonlinearity) may also cause adaptation by reducing the bump/photon gain when multiple photons hit the same microvillus simultaneously. Here, we use a Random Photon Absorption Model (RandPAM), which is the 1st module of the 4-module fly photoreceptor model, to quantify the contribution of quantum-gain-nonlinearity in light adaptation. We show how quantum-gain-nonlinearity already results from photon sampling alone. In the extreme case, when two or more simultaneous photon-hits reduce to a single sublinear value, quantum-gain-nonlinearity is preset before the phototransduction reactions adapt the quantum bump waveform. However, the contribution of quantum-gain-nonlinearity in light adaptation depends upon the likelihood of multi-photon-hits, which is strictly determined by the number of microvilli and light intensity. Specifically, its contribution to light-adaptation is marginal (≤ 1%) in fly photoreceptors with many thousands of microvilli, because the probability of simultaneous multi-photon-hits on any one microvillus is low even during daylight conditions. However, in cells with fewer sampling units, the impact of quantum-gain-nonlinearity increases with brightening light. PMID:27445779

  10. SERE: single-parameter quality control and sample comparison for RNA-Seq.

    Science.gov (United States)

    Schulze, Stefan K; Kanwar, Rahul; Gölzenleuchter, Meike; Therneau, Terry M; Beutler, Andreas S

    2012-10-03

    Assessing the reliability of experimental replicates (or global alterations corresponding to different experimental conditions) is a critical step in analyzing RNA-Seq data. Pearson's correlation coefficient r has been widely used in the RNA-Seq field even though its statistical characteristics may be poorly suited to the task. Here we present a single-parameter test procedure for count data, the Simple Error Ratio Estimate (SERE), that can determine whether two RNA-Seq libraries are faithful replicates or globally different. Benchmarking shows that the interpretation of SERE is unambiguous regardless of the total read count or the range of expression differences among bins (exons or genes), a score of 1 indicating faithful replication (i.e., samples are affected only by Poisson variation of individual counts), a score of 0 indicating data duplication, and scores >1 corresponding to true global differences between RNA-Seq libraries. On the contrary the interpretation of Pearson's r is generally ambiguous and highly dependent on sequencing depth and the range of expression levels inherent to the sample (difference between lowest and highest bin count). Cohen's simple Kappa results are also ambiguous and are highly dependent on the choice of bins. For quantifying global sample differences SERE performs similarly to a measure based on the negative binomial distribution yet is simpler to compute. SERE can therefore serve as a straightforward and reliable statistical procedure for the global assessment of pairs or large groups of RNA-Seq datasets by a single statistical parameter.

  11. Design and evaluation of a new Peltier-cooled laser ablation cell with on-sample temperature control.

    Science.gov (United States)

    Konz, Ioana; Fernández, Beatriz; Fernández, M Luisa; Pereiro, Rosario; Sanz-Medel, Alfredo

    2014-01-27

    A new custom-built Peltier-cooled laser ablation cell is described. The proposed cryogenic cell combines a small internal volume (20 cm(3)) with a unique and reliable on-sample temperature control. The use of a flexible temperature sensor, directly located on the sample surface, ensures a rigorous sample temperature control throughout the entire analysis time and allows instant response to any possible fluctuation. In this way sample integrity and, therefore, reproducibility can be guaranteed during the ablation. The refrigeration of the proposed cryogenic cell combines an internal refrigeration system, controlled by a sensitive thermocouple, with an external refrigeration system. Cooling of the sample is directly carried out by 8 small (1 cm×1 cm) Peltier elements placed in a circular arrangement in the base of the cell. These Peltier elements are located below a copper plate where the sample is placed. Due to the small size of the cooling electronics and their circular allocation it was possible to maintain a peephole under the sample for illumination allowing a much better visualization of the sample, a factor especially important when working with structurally complex tissue sections. The analytical performance of the cryogenic cell was studied using a glass reference material (SRM NIST 612) at room temperature and at -20°C. The proposed cell design shows a reasonable signal washout (signal decay within less than 10 s to background level), high sensitivity and good signal stability (in the range 6.6-11.7%). Furthermore, high precision (0.4-2.6%) and accuracy (0.3-3.9%) in the isotope ratio measurements were also observed operating the cell both at room temperature and at -20°C. Finally, experimental results obtained for the cell application to qualitative elemental imaging of structurally complex tissue samples (e.g. eye sections from a native frozen porcine eye and fresh flower leaves) demonstrate that working in cryogenic conditions is critical in such

  12. The Effect of Self-Control on Unit and Item Nonresponse in an Adolescent Sample

    Science.gov (United States)

    Watkins, Adam M.; Melde, Chris

    2007-01-01

    In "A General Theory of Crime", Gottfredson and Hirschi dispute whether valid self-report data can be collected among respondents lacking self-control. This research tests this argument by examining two processes that undermine the validity of self-report data: unit and item nonresponse. Specifically, this research addresses two questions: Within…

  13. Controlling moisture content of wood samples using a modified soil-pan decay method

    Science.gov (United States)

    Jerrold E. Winandy; Simon F. Curling; Patricia K. Lebow

    2005-01-01

    In wood, the threshold level below which decay cannot occur varies with species or type of wood product and other factors such as temperature, humidity, and propensity of exposure or service-use to allow rain-induced wetting and subsequent drying. The ability to control wood moisture content (MC) during laboratory decay testing could allow research on the moisture...

  14. The Experimental Physics and Industrial Control System architecture: Past, present, and future

    International Nuclear Information System (INIS)

    Dalesio, L.R.; Hill, J.O.; Kraimer, M.; Lewis, S.; Murray, D.; Hunt, S.; Claussen, M.; Watson, W.

    1993-01-01

    The Experimental Physics and Industrial Control System (EPICS), has been used at a number of sites for performing data acquisition, supervisory control, closed-loop control, sequential control, and operational optimization. The EPICS architecture was originally developed by a group with diverse backgrounds in physics and industrial control. The current architecture represents one instance of the ''standard model.'' It provides distributed processing and communication from any LAN device to the front end controllers. This paper will present the genealogy, current architecture, performance envelope, current installations, and planned extensions for requirements not met by the current architecture

  15. The Proteome of Ulcerative Colitis in Colon Biopsies from Adults - Optimized Sample Preparation and Comparison with Healthy Controls.

    Science.gov (United States)

    Schniers, Armin; Anderssen, Endre; Fenton, Christopher Graham; Goll, Rasmus; Pasing, Yvonne; Paulssen, Ruth Hracky; Florholmen, Jon; Hansen, Terkel

    2017-12-01

    The purpose of the study was to optimize the sample preparation and to further use an improved sample preparation to identify proteome differences between inflamed ulcerative colitis tissue from untreated adults and healthy controls. To optimize the sample preparation, we studied the effect of adding different detergents to a urea containing lysis buffer for a Lys-C/trypsin tandem digestion. With the optimized method, we prepared clinical samples from six ulcerative colitis patients and six healthy controls and analysed them by LC-MS/MS. We examined the acquired data to identify differences between the states. We improved the protein extraction and protein identification number by utilizing a urea and sodium deoxycholate containing buffer. Comparing ulcerative colitis and healthy tissue, we found 168 of 2366 identified proteins differently abundant. Inflammatory proteins are higher abundant in ulcerative colitis, proteins related to anion-transport and mucus production are lower abundant. A high proportion of S100 proteins is differently abundant, notably with both up-regulated and down-regulated proteins. The optimized sample preparation method will improve future proteomic studies on colon mucosa. The observed protein abundance changes and their enrichment in various groups improve our understanding of ulcerative colitis on protein level. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Investigating the factorial structure and availability of work time control in a representative sample of the Swedish working population.

    Science.gov (United States)

    Albrecht, Sophie C; Kecklund, Göran; Tucker, Philip; Leineweber, Constanze

    2016-05-01

    Past research has often neglected the sub-dimensions of work time control (WTC). Moreover, differences in levels of WTC with respect to work and demographic characteristics have not yet been examined in a representative sample. We investigated these matters in a recent sample of the Swedish working population. The study was based on the 2014 data collection of the Swedish Longitudinal Occupational Survey of Health. We assessed the structure of the WTC measure using exploratory and confirmatory factor analysis. Differences in WTC by work and demographic characteristics were examined with independent samplet-tests, one-way ANOVAs and gender-stratified logistic regressions. Best model fit was found for a two-factor structure that distinguished between control over daily hours and control over time off (root mean square error of approximation = 0.06; 95% CI 0.04 to 0.09; Comparative Fit Index (CFI) = 0.99). Women, shift and public-sector workers reported lower control in relation to both factors. Age showed small associations with WTC, while a stronger link was suggested for civil status and family situation. Night, roster and rotating shift work seemed to be the most influential factors on reporting low control over daily hours and time off. Our data confirm the two-dimensional structure underlying WTC, namely the components 'control over daily hours' and 'control over time off'. Women, public-sector and shift workers reported lower levels of control. Future research should examine the public health implications of WTC, in particular whether increased control over daily hours and time off can reduce health problems associated with difficult working-time arrangements. © 2015 the Nordic Societies of Public Health.

  17. The design status of CSNS experimental control system

    International Nuclear Information System (INIS)

    Jian Zhuang; Yuanping Chu; Dapeng Jin; Yuqian Liu; Yinhong Zhang; Zhuoyu Zhang; Kejun Zhu; Libin Ding; Lei Hu; Jiajie Li; Yali, Liu

    2012-01-01

    To meet the increasing demand from user community, China decided to build a world-class spallation neutron source, called CSNS (China Spallation Neutron Source). It can provide users a neutron scattering platform with high flux, wide wavelength range and high efficiency. CSNS construction is expected to start in 2011 and will last 6.5 years. The control system of CSNS is divided into accelerator control system and experimental control system. CSNS Experimental Control System is based on EPICS architecture, offering device operation and device debug interface, communication between devices, environment monitor, machine and personnel protection, interface to accelerator control system, overall system monitor and database service. The control system is divided into 4 parts, such as front control layer, local and global control layer based on EPICS, database and network service and the others. The front control layer is based on YOKOGAWA PLC and other controllers. EPICS includes local and global control layer provides all system control and information exchange. Embedded PLC YOKOGAWA RP61 and others is to be used as communication node between front layer and EPICS. Database service provides system configuration and historical data. From the experience of BESIII, MySQL is an option. The system will be developed in Dongguan, Guangdong province and Beijing. So VPN will be used to help development. Now, total 9 persons are working on this system. (authors)

  18. Optimizing the data acquisition rate for a remotely controllable structural monitoring system with parallel operation and self-adaptive sampling

    International Nuclear Information System (INIS)

    Sheng, Wenjuan; Guo, Aihuang; Liu, Yang; Azmi, Asrul Izam; Peng, Gang-Ding

    2011-01-01

    We present a novel technique that optimizes the real-time remote monitoring and control of dispersed civil infrastructures. The monitoring system is based on fiber Bragg gating (FBG) sensors, and transfers data via Ethernet. This technique combines parallel operation and self-adaptive sampling to increase the data acquisition rate in remote controllable structural monitoring systems. The compact parallel operation mode is highly efficient at achieving the highest possible data acquisition rate for the FBG sensor based local data acquisition system. Self-adaptive sampling is introduced to continuously coordinate local acquisition and remote control for data acquisition rate optimization. Key issues which impact the operation of the whole system, such as the real-time data acquisition rate, data processing capability, and buffer usage, are investigated. The results show that, by introducing parallel operation and self-adaptive sampling, the data acquisition rate can be increased by several times without affecting the system operating performance on both local data acquisition and remote process control

  19. Sample-based reporting of official national control of veterinary drug residues

    DEFF Research Database (Denmark)

    Andersen, Jens Hinge; Jensen, Louise Grønhøj Hørbye; Madsen, Helle L.

    assessment as well as risk management. The European Food Safety Authority has been assigned with the task to set up a system for data collection based on individual analytical results. A pilot project has been launched with participants from eleven Member States for parallel reporting of monitoring results...... from 2015 in aggregated form as well as individual analytical results using a standardised data model. The challenges that face the pilot participants include provisions for categorised sample information, specific method performance data, result evaluation and follow-up actions. Experience gained...

  20. An extension of command shaping methods for controlling residual vibration using frequency sampling

    Science.gov (United States)

    Singer, Neil C.; Seering, Warren P.

    1992-01-01

    The authors present an extension to the impulse shaping technique for commanding machines to move with reduced residual vibration. The extension, called frequency sampling, is a method for generating constraints that are used to obtain shaping sequences which minimize residual vibration in systems such as robots whose resonant frequencies change during motion. The authors present a review of impulse shaping methods, a development of the proposed extension, and a comparison of results of tests conducted on a simple model of the space shuttle robot arm. Frequency shaping provides a method for minimizing the impulse sequence duration required to give the desired insensitivity.