Performance Tests of a Mechanical Pump in Sodium Environment

Energy Technology Data Exchange (ETDEWEB)

Cho, Chungho; Kim, Jong-Man; Ko, Yung Joo; Kim, Byeongyeon; Cho, Youngil; Jung, Min-Hwan; Gam, Da-Young; Lee, Yong Bum; Jeong, Ji-Young; Kim, Jong-Bum [KAERI, Daejeon (Korea, Republic of)

2016-05-15

Water is often selected as a surrogate test fluid because it is not only cheap, easily available and easy to handle but also its important hydraulic properties (density and kinematic viscosity) are very similar to that of the sodium. Nevertheless, to ensure the performance, safety, and operability of major components before its installation in the SFR, a series of demonstration experiments of some components in sodium environment should be positively necessary. So, SFR NSSS System Design Division of Korea Atomic Energy Research Institute (KAERI) built various sodium experimental facilities, especially STELLA-1 in 2012. STELLA-1 (Sodium inTegral Effect test Loop for safety simuLation and Assessment) is a large-scale separated effect test facility for demonstrating the thermal-hydraulic performances of major components such as a Sodium-to-Sodium heat exchanger (DHX), Sodium-to-Air heat exchanger (AHX) of the decay heat removal system, and mechanical sodium pump of the primary heat transport system (PHTS). The mechanical pump in-sodium performance test was successfully performed with good reproducibility of the experiment and data to compare hydraulic characteristic of a mechanical pump in-water was collected. In effect of temperature variation on the pump pressure head, reduction of pump pressure head at 250℃ by 0.57% of that of 300℃ maybe the result of an increase in sodium viscosity by 13.6% according to operating temperature decrease by 50℃. Also, we confirmed that the more flywheel weight, the longer halving time and the more initial flow rate when the pump seized, the shorter halving time. The results of the mechanical pump performance test data in sodium environment will be used to compare with that of the in water environment after the evaluation of measurement uncertainty for tests.

Semiselective test for the detection of first- and second-division nondisjunction in Drosophila melanogaster

International Nuclear Information System (INIS)

Foureman, P.A.

1986-01-01

Little is known about the relative frequency of induction of nondisjunction in the first and second divisions of meiosis. The killer of prune system is a semiselective Drosophila aneuploidy assay designed to detect chromosome gain resulting from first- or second-division nondisjunction in males. The system can also detect X-Y interchange. Extensive data from nonmutagenized controls indicate that all the expected phenotypes can be recovered. Spontaneous nondisjunction in the first division is three times more frequent than in the second division. Spontaneous interchange between the X chromosome and YS is six times more frequent than between the X chromosome and YL. Exposures of larval males to X-rays, 35 degrees C heat shock, and colchicine were performed. X-ray exposure induced an increase in X-Y interchange events only. A 24-hr heat shock induced an increase in first-division nondisjunction and one type of interchange event. Colchicine failed to induce both nondisjunction and interchange, although it did decrease fertility. The Killer of prune test is of potential value because it allows for the assessment of the relative sensitivities of the two meiotic divisions to perturbations in chromosome number

Phenotypic plasticity and effects of selection on cell division symmetry in Escherichia coli.

Directory of Open Access Journals (Sweden)

Uttara N Lele

Full Text Available Aging has been demonstrated in unicellular organisms and is presumably due to asymmetric distribution of damaged proteins and other components during cell division. Whether the asymmetry-induced aging is inevitable or an adaptive and adaptable response is debated. Although asymmetric division leads to aging and death of some cells, it increases the effective growth rate of the population as shown by theoretical and empirical studies. Mathematical models predict on the other hand, that if the cells divide symmetrically, cellular aging may be delayed or absent, growth rate will be reduced but growth yield will increase at optimum repair rates. Therefore in nutritionally dilute (oligotrophic environments, where growth yield may be more critical for survival, symmetric division may get selected. These predictions have not been empirically tested so far. We report here that Escherichia coli grown in oligotrophic environments had greater morphological and functional symmetry in cell division. Both phenotypic plasticity and genetic selection appeared to shape cell division time asymmetry but plasticity was lost on prolonged selection. Lineages selected on high nutrient concentration showed greater frequency of presumably old or dead cells. Further, there was a negative correlation between cell division time asymmetry and growth yield but there was no significant correlation between asymmetry and growth rate. The results suggest that cellular aging driven by asymmetric division may not be hardwired but shows substantial plasticity as well as evolvability in response to the nutritional environment.

Fusion energy division computer systems network

International Nuclear Information System (INIS)

Hammons, C.E.

1980-12-01

The Fusion Energy Division of the Oak Ridge National Laboratory (ORNL) operated by Union Carbide Corporation Nuclear Division (UCC-ND) is primarily involved in the investigation of problems related to the use of controlled thermonuclear fusion as an energy source. The Fusion Energy Division supports investigations of experimental fusion devices and related fusion theory. This memo provides a brief overview of the computing environment in the Fusion Energy Division and the computing support provided to the experimental effort and theory research

Variable threshold algorithm for division of labor analyzed as a dynamical system.

Science.gov (United States)

Castillo-Cagigal, Manuel; Matallanas, Eduardo; Navarro, Iñaki; Caamaño-Martín, Estefanía; Monasterio-Huelin, Félix; Gutiérrez, Álvaro

2014-12-01

Division of labor is a widely studied aspect of colony behavior of social insects. Division of labor models indicate how individuals distribute themselves in order to perform different tasks simultaneously. However, models that study division of labor from a dynamical system point of view cannot be found in the literature. In this paper, we define a division of labor model as a discrete-time dynamical system, in order to study the equilibrium points and their properties related to convergence and stability. By making use of this analytical model, an adaptive algorithm based on division of labor can be designed to satisfy dynamic criteria. In this way, we have designed and tested an algorithm that varies the response thresholds in order to modify the dynamic behavior of the system. This behavior modification allows the system to adapt to specific environmental and collective situations, making the algorithm a good candidate for distributed control applications. The variable threshold algorithm is based on specialization mechanisms. It is able to achieve an asymptotically stable behavior of the system in different environments and independently of the number of individuals. The algorithm has been successfully tested under several initial conditions and number of individuals.

Lower extremity functional tests and risk of injury in division iii collegiate athletes.

Science.gov (United States)

Brumitt, Jason; Heiderscheit, Bryan C; Manske, Robert C; Niemuth, Paul E; Rauh, Mitchell J

2013-06-01

Functional tests have been used primarily to assess an athlete's fitness or readiness to return to sport. The purpose of this prospective cohort study was to determine the ability of the standing long jump (SLJ) test, the single-leg hop (SLH) for distance test, and the lower extremity functional test (LEFT) as preseason screening tools to identify collegiate athletes who may be at increased risk for a time-loss sports-related low back or lower extremity injury. A total of 193 Division III athletes from 15 university teams (110 females, age 19.1 ± 1.1 y; 83 males, age 19.5 ± 1.3 y) were tested prior to their sports seasons. Athletes performed the functional tests in the following sequence: SLJ, SLH, LEFT. The athletes were then prospectively followed during their sports season for occurrence of low back or LE injury. Female athletes who completed the LEFT in $118 s were 6 times more likely (OR=6.4, 95% CI: 1.3, 31.7) to sustain a thigh or knee injury. Male athletes who completed the LEFT in #100 s were more likely to experience a time-loss injury to the low back or LE (OR=3.2, 95% CI: 1.1, 9.5) or a foot or ankle injury (OR=6.7, 95% CI: 1.5, 29.7) than male athletes who completed the LEFT in 101 s or more. Female athletes with a greater than 10% side-to-side asymmetry between SLH distances had a 4-fold increase in foot or ankle injury (cut point: >10%; OR=4.4, 95% CI: 1.2, 15.4). Male athletes with SLH distances (either leg) at least 75% of their height had at least a 3-fold increase (OR=3.6, 95% CI: 1.2, 11.2 for the right LE; OR=3.6, 95% CI: 1.2, 11.2 for left LE) in low back or LE injury. The LEFT and the SLH tests appear useful in identifying Division III athletes at risk for a low back or lower extremity sports injury. Thus, these tests warrant further consideration as preparticipatory screening examination tools for sport injury in this population. The single-leg hop for distance and the lower extremity functional test, when administered to Division III

Materials division facilities and equipment

International Nuclear Information System (INIS)

Biest, O. v.d.

1984-01-01

The research activities of the Division at the Petten Establishment have the aims of characterising the properties of high temperature materials in industrial process environments and of understanding the structures involved in order to gain an insight into behavioural mechanisms. Metallic materials fall within the scope of the programme; the activities are, at present, almost entirely concerned with austenitic steels and nickel based alloys. Starting in 1984, advanced ceramic materials will be studied as well. The equipment available permits the study of mechanical properties in controlled gaseous environments, of the rates and mechanisms of corrosive reactions between materials and those environments, and of the surface and bulk structures by advanced physical techniques. Special preparation and treatment techniques are available. The Division has developed a Data Bank on high temperature alloys. It also operates an information Centre, the activities of which include the organisation of scientific meetings, the commissioning of ''state of the art'' studies on topics in the field of high temperature materials and their applications and the development of a inventory of current research activities in the field in Europe. This booklet is intended to present the facilities and services of the Division to the organizations which are interested in its programmes of work

Technology Development, Evaluation, and Application (TDEA) FY 1998 Progress Report Environment, Safety, and Health (ESH) Division

Energy Technology Data Exchange (ETDEWEB)

Larry G. Hoffman; Kenneth Alvar; Thomas Buhl; Bruce Erdal; Philip Fresquez; Elizabeth Foltyn; Wayne Hansen; Bruce Reinert

1999-06-01

This progress report presents the results of 10 projects funded ($504K) in FY98 by the Technology Development, Evaluation, and Application (TDEA) Committee of the Environment, Safety, and Health Division. Nine projects are new for this year; two projects were completed in their third and final TDEA-funded year. As a result of their TDEA-funded projects, investigators have published 19 papers in professional journals, proceedings, or Los Alamos reports and presented their work at professional meetings. Supplemental funds and in-kind contributions, such as staff time, instrument use, and work space were also provided to the TDEA-funded projects by organizations external to ESH Division. Products generated from the projects funded in FY98 included a new extremity dosimeter that replaced the previously used finger-ring dosimeters, a light and easy-to-use detector to measure energy deposited by neutron interactions, and a device that will allow workers to determine the severity of a hazard.

Energy and Environment Division annual report, 1978

Energy Technology Data Exchange (ETDEWEB)

Camp, J.A. (ed.)

1978-01-01

Research activities of this Division are reported under nine separate programs, namely: Energy Analysis; Solar Energy; Energy-Efficient Buildings; Chemical Process Research and Development; Environmental Research; Atmospheric Aerosol Research; Oil Shale Research; Instrumentation Development; and Combustion Research. A separate abstract was prepared for each of the nine programs, each of which contained several individual research summaries, with responsible researchers listed. All of the abstracts will appear in Energy Research Abstracts (ERA), and five will appear in Energy Abstracts for Policy Analysis (EAPA).

CSIR Division of Mining Technology annual review 1993/94

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

The Division of Mining Technology of the CSIR (Council for Scientific and Industrial Research) works in partnership with the mining industry to solve problems threatening the health, safety and well-being of the workforce, and the productivity of mining operations through the development and implementation of knowledge and technology. The annual review describes the Division's research projects in the following field: rock engineering (for gold, platinum and coal mining); mining environment; occupational hygiene; surface environment; and mining equipment and systems (systems and equipment, orebody information, coal mining and causes of accidents). Details are also given of the Division's publications, research and consultancy services and information centre.

Division of household tasks and financial management

NARCIS (Netherlands)

Antonides, G.

2011-01-01

Both the standard economic model and bargaining theory make predictions about financial management and the division of household labor between household partners. Using a large Internet survey, we have tested several predictions about task divisions reported by Dutch household partners. The division

Safety and Health Division achievements during 40 years

International Nuclear Information System (INIS)

Noriah Mod Ali

2012-01-01

During her speech, presenter outlined several issues regarding on establishment of Safety and Health Division since 40 years. This division contain of 3 sub unit; Physical Safety Group, Medical Physic Group and Non-ionizing Radiation group (NIR). The objectives of this division to implement R and D activities and services regarding safety and radiological health also non-radiological to ensure public safety, environment and asset suit with obligations established by authorities, IAEA standards and regulations.(author)

Distinguishing Environment and System in Coloured Petri Net Models of Reactive Systems

DEFF Research Database (Denmark)

Tjell, Simon

2007-01-01

This paper introduces and formally defines the environment-and-system-partitioned property for behavioral models of reactive systems expressed in the formal modeling language Coloured Petri Net. The purpose of the formalization is to make it possible to automatically validate any CPN model...... with respect to this property based on structural analysis. A model has the environment-and-system-partitioned property if it is based on a clear division between environment and system. This division is important in many model-driven approaches to software development such as model-based testing and automated...

47 CFR 2.1503 - Test environment.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Test environment. 2.1503 Section 2.1503 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL... Radiobeacons (EPIRBs) General § 2.1503 Test environment. (a) Measurement sites. Radiated emission tests for...

Earth Sciences Division annual report 1990

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-06-01

This Annual Report presents summaries of selected representative research activities grouped according to the principal disciplines of the Earth Sciences Division: Reservoir Engineering and Hydrogeology, Geology and Geochemistry, and Geophysics and Geomechanics. Much of the Division`s research deals with the physical and chemical properties and processes in the earth`s crust, from the partially saturated, low-temperature near-surface environment to the high-temperature environments characteristic of regions where magmatic-hydrothermal processes are active. Strengths in laboratory and field instrumentation, numerical modeling, and in situ measurement allow study of the transport of mass and heat through geologic media -- studies that now include the appropriate chemical reactions and the hydraulic-mechanical complexities of fractured rock systems. Of particular note are three major Division efforts addressing problems in the discovery and recovery of petroleum, the application of isotope geochemistry to the study of geodynamic processes and earth history, and the development of borehole methods for high-resolution imaging of the subsurface using seismic and electromagnetic waves. In 1989 a major DOE-wide effort was launched in the areas of Environmental Restoration and Waste Management. Many of the methods previously developed for and applied to deeper regions of the earth will in the coming years be turned toward process definition and characterization of the very shallow subsurface, where man-induced contaminants now intrude and where remedial action is required.

Biennial activity report of the Division for PIE and NDT Development [for years] 1989-1990

International Nuclear Information System (INIS)

Babu Rao, C.; Shyamsunder, M.T.; Murugan, S.; Ramabathiran, A.; Rajagopalan, C.; Bhattacharya, D.K.; Kumar, P.V.; Kalyanasundaram, P.; Kasiviswanathan, K.V.

1992-01-01

This is the first biennial report of the Division for Post-Irradiation Examination and Non-Destructive Testing (DPEND) of the Indira Gandhi Centre for Atomic Research, Kalpakkam. It covers the research and development (R and D) activities of the Division during 1989 and 1990. The R and D activities of the Division are both multidisciplinary and interdisciplinary. The principal areas of R and D of DPEND are post-irradiation examination of fuel and structural materials, irradiation experiments, non-destructive evaluation for material characterisation, quality assurance and inservice inspection, failure investigations, remote technology etc. These R and D activities are reported in the form of extended summaries arranged under the headings: research and development in non-destructive evaluation, material characterisation, instrumentation, development of techniques, software development, mechanical equipment and systems (development and commissioning), inspections, and failure analysis. Some of the highlights of these activities are : (1)setting up of a radio metallurgy laboratory with hot cells with recirculating nitrogen gas environment to facilitate post-irradiation examination of the carbide fuel of the Fast Breeder Test Reactor. (FBTR), (2) development of the remote milling and drilling machine and development of pressurised capsules for irradiation creep measurement experiments in FBTR, (b) fabrication of non-destructive testing (NDT) reference standards with controlled defects for use in Nuclear Fuel Complex, Hyderabad. There are a number of appendices listing publications, conference paper, invited talks, internal reports etc. by the scientists of the Division and also awards/prizes won by the scientists. A staff-chart of the Division is also given. (M.G.B.)

Weightless environment simulation test; Mujuryo simulation shiken

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, K.; Yamamoto, T.; Kato, F. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1997-07-20

Kawasaki Heavy Industries, Ltd., delivered a Weightless Environment Test System (WETS) to National Space Development Agency of Japan in 1994. This system creates a weightless environment similar to that in space by balancing gravity and buoyancy in the water, and is constituted of a large water tank, facilities to supply air and cooling water to space suits worn in the water, etc. In this report, a weightless environment simulation test and the facilities to supply air and cooling water are described. In the weightless environment simulation test, the astronaut to undergo tests and training wears a space suit quite similar to the suit worn on the orbit, and performs EVA/IVA (extravehicular activities/intravehicular activities) around a JEM (Japanese Experimental Module) mockup installed in the water verifying JEM design specifications, preparing manuals for operations on the orbit, or receives basic space-related drill and training. An EVA weightless environment simulation test No. 3 was accomplished with success in January, 1997, when the supply of breathing water and cooling water to the space suit, etc., were carried out with safety and reliability. 2 refs., 8 figs., 2 tabs.

Earth Sciences Division annual report 1990

International Nuclear Information System (INIS)

1991-06-01

This Annual Report presents summaries of selected representative research activities grouped according to the principal disciplines of the Earth Sciences Division: Reservoir Engineering and Hydrogeology, Geology and Geochemistry, and Geophysics and Geomechanics. Much of the Division's research deals with the physical and chemical properties and processes in the earth's crust, from the partially saturated, low-temperature near-surface environment to the high-temperature environments characteristic of regions where magmatic-hydrothermal processes are active. Strengths in laboratory and field instrumentation, numerical modeling, and in situ measurement allow study of the transport of mass and heat through geologic media -- studies that now include the appropriate chemical reactions and the hydraulic-mechanical complexities of fractured rock systems. Of particular note are three major Division efforts addressing problems in the discovery and recovery of petroleum, the application of isotope geochemistry to the study of geodynamic processes and earth history, and the development of borehole methods for high-resolution imaging of the subsurface using seismic and electromagnetic waves. In 1989 a major DOE-wide effort was launched in the areas of Environmental Restoration and Waste Management. Many of the methods previously developed for and applied to deeper regions of the earth will in the coming years be turned toward process definition and characterization of the very shallow subsurface, where man-induced contaminants now intrude and where remedial action is required

2002 Chemical Engineering Division annual report

International Nuclear Information System (INIS)

Lewis, D.; Graziano, D.; Miller, J. F.

2003-01-01

The Chemical Engineering Division is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. The Division is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory; Environment, Safety, and Health Analytical Chemistry services; and Dosimetry and Radioprotection services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature superconductors. Our wide-ranging expertise finds ready application in solving energy and environmental problems. Division personnel are frequently called on by

The Significance of Family, Environment, and College Preparation: A Study of Factors Influencing Graduation and Persistence Rates of African American Males Playing Division I Basketball

Science.gov (United States)

Mitchell, Enzley, IV

2017-01-01

The purpose of this study was to identify specific external factors including family composition, pre-college environment, and college preparation that contribute to why some African American males playing basketball at the NCAA Division I level graduate and persist while others do not. Despite an aggressive advertising campaign from the NCAA…

Division of labour in the yeast

DEFF Research Database (Denmark)

Wloch-Salamon, Dominika M.; Fisher, Roberta May; Regenberg, Birgitte

2017-01-01

. Saccharomyces cerevisiae displays several phenotypes that could be considered a division of labour, including quiescence, apoptosis and biofilm formation, but they have not been explicitly treated as such. We discuss each of these examples, using a definition of division of labour that involves phenotypic...... variation between cells within a population, cooperation between cells performing different tasks and maximization of the inclusive fitness of all cells involved. We then propose future research directions and possible experimental tests using S. cerevisiae as a model organism for understanding the genetic...... mechanisms and selective pressures that can lead to the evolution of the very first stages of a division of labour....

Macromolecular interactions of the bacterial division FtsZ protein: from quantitative biochemistry and crowding to reconstructing minimal divisomes in the test tube.

Science.gov (United States)

Rivas, Germán; Alfonso, Carlos; Jiménez, Mercedes; Monterroso, Begoña; Zorrilla, Silvia

2013-06-01

The division of Escherichia coli is an essential process strictly regulated in time and space. It requires the association of FtsZ with other proteins to assemble a dynamic ring during septation, forming part of the functionally active division machinery, the divisome. FtsZ reversibly interacts with FtsA and ZipA at the cytoplasmic membrane to form a proto-ring, the first molecular assembly of the divisome, which is ultimately joined by the rest of the division-specific proteins. In this review we summarize the quantitative approaches used to study the activity, interactions, and assembly properties of FtsZ under well-defined solution conditions, with the aim of furthering our understanding of how the behavior of FtsZ is controlled by nucleotides and physiological ligands. The modulation of the association and assembly properties of FtsZ by excluded-volume effects, reproducing in part the natural crowded environment in which this protein has evolved to function, will be described. The subsequent studies on the reactivity of FtsZ in membrane-like systems using biochemical, biophysical, and imaging technologies are reported. Finally, we discuss the experimental challenges to be met to achieve construction of the minimum protein set needed to initiate bacterial division, without cells, in a cell-like compartment. This integrated approach, combining quantitative and synthetic strategies, will help to support (or dismiss) conclusions already derived from cellular and molecular analysis and to complete our understanding on how bacterial division works.

Soldier Satisfaction with Life in Restructured Units during Phase 1 of the Restructuring of the Heavy Division Test

Science.gov (United States)

1979-09-01

working and living in their units during the estructuring of the Heavy Division test at Fort Hood, TX. The questionnaire -as administered to unit...to a control group of soldiers who did not estructure . Results of the study showed that immediately following DO ,’, 1473 EDITIONOF IOV SISO SOLFT

Testing the “division of labor hypothesis” of aphasic verb production using big-data

Directory of Open Access Journals (Sweden)

Yasmeen Faroqi-Shah

2015-05-01

Individuals with aphasia and healthy controls produced a similar proportion of light verbs (.38, U(298 = 13,129, p > 0.05. Linear regression analysis revealed three significant predictors of high light verb use in aphasia: greater syntactic complexity (high DSS score, lower semantic richness (low idea density and lower Verb Naming Test scores (picture naming of heavy verbs, Cho-Reyes & Thompson, 2012. These findings support the division of labor in aphasia – persons with stronger syntactic abilities produce more light verbs and have lower semantic ability (Gordon & Dell, 2003.

Development and Application of a Two-Tier Multiple-Choice Diagnostic Test for High School Students' Understanding of Cell Division and Reproduction

Science.gov (United States)

Sesli, Ertugrul; Kara, Yilmaz

2012-01-01

This study involved the development and application of a two-tier diagnostic test for measuring students' understanding of cell division and reproduction. The instrument development procedure had three general steps: defining the content boundaries of the test, collecting information on students' misconceptions, and instrument development.…

Prediction of software operational reliability using testing environment factors

International Nuclear Information System (INIS)

Jung, Hoan Sung; Seong, Poong Hyun

1995-01-01

For many years, many researches have focused on the quantification of software reliability and there are many models developed to quantify software reliability. Most software reliability models estimate the reliability with the failure data collected during the test assuming that the test environments well represent the operation profile. The experiences show that the operational reliability is higher than the test reliability User's interest is on the operational reliability rather than on the test reliability, however. With the assumption that the difference in reliability results from the change of environment, testing environment factors comprising the aging factor and the coverage factor are defined in this study to predict the ultimate operational reliability with the failure data. It is by incorporating test environments applied beyond the operational profile into testing environment factors. The application results are close to the actual data

Computing, Environment and Life Sciences | Argonne National Laboratory

Science.gov (United States)

Computing, Environment and Life Sciences Research Divisions BIOBiosciences CPSComputational Science DSLData Argonne Leadership Computing Facility Biosciences Division Environmental Science Division Mathematics and Computer Science Division Facilities and Institutes Argonne Leadership Computing Facility News Events About

UAS-NAS Flight Test Series 3: Test Environment Report

Science.gov (United States)

Hoang, Ty; Murphy, Jim; Otto, Neil

2016-01-01

The desire and ability to fly Unmanned Aircraft Systems (UAS) in the National Airspace System (NAS) is of increasing urgency. The application of unmanned aircraft to perform national security, defense, scientific, and emergency management are driving the critical need for less restrictive access by UAS to the NAS. UAS represent a new capability that will provide a variety of services in the government (public) and commercial (civil) aviation sectors. The growth of this potential industry has not yet been realized due to the lack of a common understanding of what is required to safely operate UAS in the NAS. NASA's UAS Integration in the NAS Project is conducting research in the areas of Separation Assurance/Sense and Avoid Interoperability (SSI), Human Systems Integration (HSI), and Communications (Comm), and Certification to support reducing the barriers of UAS access to the NAS. This research is broken into two research themes namely, UAS Integration and Test Infrastructure. UAS Integration focuses on airspace integration procedures and performance standards to enable UAS integration in the air transportation system, covering Detect and Avoid (DAA) performance standards, command and control performance standards, and human systems integration. The focus of Test Infrastructure is to enable development and validation of airspace integration procedures and performance standards, including integrated test and evaluation. In support of the integrated test and evaluation efforts, the Project will develop an adaptable, scalable, and schedulable relevant test environment capable of evaluating concepts and technologies for unmanned aircraft systems to safely operate in the NAS. To accomplish this task, the Project is conducting a series of human-in-the-loop (HITL) and flight test activities that integrate key concepts, technologies and/or procedures in a relevant air traffic environment. Each of the integrated events will build on the technical achievements, fidelity, and

Prediction of safety critical software operational reliability from test reliability using testing environment factors

International Nuclear Information System (INIS)

Jung, Hoan Sung; Seong, Poong Hyun

1999-01-01

It has been a critical issue to predict the safety critical software reliability in nuclear engineering area. For many years, many researches have focused on the quantification of software reliability and there have been many models developed to quantify software reliability. Most software reliability models estimate the reliability with the failure data collected during the test assuming that the test environments well represent the operation profile. User's interest is however on the operational reliability rather than on the test reliability. The experiences show that the operational reliability is higher than the test reliability. With the assumption that the difference in reliability results from the change of environment, from testing to operation, testing environment factors comprising the aging factor and the coverage factor are developed in this paper and used to predict the ultimate operational reliability with the failure data in testing phase. It is by incorporating test environments applied beyond the operational profile into testing environment factors. The application results show that the proposed method can estimate the operational reliability accurately. (Author). 14 refs., 1 tab., 1 fig

Energy Technology Division research summary 2001

International Nuclear Information System (INIS)

2001-01-01

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the U.S. Department of Energy. As shown on the preceding page, the Division is organized into eight sections, four with concentrations in the materials area and four in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officer, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. This Overview highlights some major ET research areas. Research related to the operational safety of commercial light water nuclear reactors (LWRs) for the U.S. Nuclear Regulatory Commission (NRC) remains a significant area of interest for the Division. We currently have programs on environmentally assisted cracking, steam generator integrity, and the integrity of high-burnup fuel during loss-of-coolant accidents. The bulk of the NRC research work is carried out by three ET sections: Corrosion and Mechanics of Materials; Irradiation Performance; and Sensors, Instrumentation, and Nondestructive Evaluation

Ecological Research Division, Marine Research Program

Energy Technology Data Exchange (ETDEWEB)

1980-05-01

This report presents program summaries of the various projects sponsored during 1979 by the Marine Research Program of the Ecological Research Division. Program areas include the effects of petroleum hydrocarbons on the marine environment; a study of the baseline ecology of a proposed OTEC site near Puerto Rico; the environmental impact of offshore geothermal energy development; the movement of radionuclides through the marine environment; the environmental aspects of power plant cooling systems; and studies of the physical and biological oceangraphy of the continental shelves bordering the United States.

Ecological Research Division, Marine Research Program

International Nuclear Information System (INIS)

1980-05-01

This report presents program summaries of the various projects sponsored during 1979 by the Marine Research Program of the Ecological Research Division. Program areas include the effects of petroleum hydrocarbons on the marine environment; a study of the baseline ecology of a proposed OTEC site near Puerto Rico; the environmental impact of offshore geothermal energy development; the movement of radionuclides through the marine environment; the environmental aspects of power plant cooling systems; and studies of the physical and biological oceangraphy of the continental shelves bordering the United States

UKAEA Government Division Annual Review 1994-95

International Nuclear Information System (INIS)

1995-01-01

This is the first annual review of the United Kingdom Atomic Energy Authority (UKAEA) Government Division. The Division was set up in April 1994 with the primary responsibility of completing the UKAEA's nuclear mission by caring for and decommissioning the radioactive facilities used in pursuit of the national nuclear programme over the past 50 years; this includes the safe disposal of the resulting radioactive waste. The progress made in the first year towards carrying out this responsibility at the lowest cost while continuing to ensure safety and protection of the environment is reported. Other responsibilities of Government Division which are reviewed include: management of the UKAEA's sites, buildings and operating facilities; oversight of the United Kingdom fusion research programme and provision for the Joint European Torus which is situated next to the Culham fusion site; and the UKAEA Constabulary. Appended to the review are a financial statement and a list of the main decommissioning tasks. (UK)

Energy Technology Division research summary - 1999.

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-31

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy. As shown on the preceding page, the Division is organized into ten sections, five with concentrations in the materials area and five in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officers, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. The Division's capabilities are generally applied to issues associated with energy production, transportation, utilization, or conservation, or with environmental issues linked to energy. As shown in the organization chart on the next page, the Division reports administratively to the Associate Laboratory Director (ALD) for Energy and Environmental Science and Technology (EEST) through the General Manager for Environmental and Industrial Technologies. While most of our programs are under the purview of the EEST ALD, we also have had programs funded under every one of the ALDs. Some of our research in superconductivity is funded through the Physical Research Program ALD. We also continue to work on a number of nuclear-energy-related programs under the ALD for Engineering Research. Detailed descriptions of our programs on a section-by-section basis are provided in the remainder of this book.

The stem cell division theory of cancer.

Science.gov (United States)

López-Lázaro, Miguel

2018-03-01

All cancer registries constantly show striking differences in cancer incidence by age and among tissues. For example, lung cancer is diagnosed hundreds of times more often at age 70 than at age 20, and lung cancer in nonsmokers occurs thousands of times more frequently than heart cancer in smokers. An analysis of these differences using basic concepts in cell biology indicates that cancer is the end-result of the accumulation of cell divisions in stem cells. In other words, the main determinant of carcinogenesis is the number of cell divisions that the DNA of a stem cell has accumulated in any type of cell from the zygote. Cell division, process by which a cell copies and separates its cellular components to finally split into two cells, is necessary to produce the large number of cells required for living. However, cell division can lead to a variety of cancer-promoting errors, such as mutations and epigenetic mistakes occurring during DNA replication, chromosome aberrations arising during mitosis, errors in the distribution of cell-fate determinants between the daughter cells, and failures to restore physical interactions with other tissue components. Some of these errors are spontaneous, others are promoted by endogenous DNA damage occurring during quiescence, and others are influenced by pathological and environmental factors. The cell divisions required for carcinogenesis are primarily caused by multiple local and systemic physiological signals rather than by errors in the DNA of the cells. As carcinogenesis progresses, the accumulation of DNA errors promotes cell division and eventually triggers cell division under permissive extracellular environments. The accumulation of cell divisions in stem cells drives not only the accumulation of the DNA alterations required for carcinogenesis, but also the formation and growth of the abnormal cell populations that characterize the disease. This model of carcinogenesis provides a new framework for understanding the

The Time Division Multi-Channel Communication Model and the Correlative Protocol Based on Quantum Time Division Multi-Channel Communication

International Nuclear Information System (INIS)

Liu Xiao-Hui; Pei Chang-Xing; Nie Min

2010-01-01

Based on the classical time division multi-channel communication theory, we present a scheme of quantum time-division multi-channel communication (QTDMC). Moreover, the model of quantum time division switch (QTDS) and correlative protocol of QTDMC are proposed. The quantum bit error rate (QBER) is analyzed and the QBER simulation test is performed. The scheme shows that the QTDS can carry out multi-user communication through quantum channel, the QBER can also reach the reliability requirement of communication, and the protocol of QTDMC has high practicability and transplantable. The scheme of QTDS may play an important role in the establishment of quantum communication in a large scale in the future. (general)

Automated corrosion fatigue crack growth testing in pressurized water environments

International Nuclear Information System (INIS)

Ceschini, L.J.; Liaw, P.K.; Rudd, G.E.; Logsdon, W.A.

1984-01-01

This paper describes in detail a novel approach to construct a test facility for developing corrosion fatigue crack growth rate (FCGR) properties in aggressive environments. The environment studied is that of a pressurized water reactor (PWR) at 288 0 C (550 0 F) and 13.8 MPa (200 psig). To expedite data generation, each chamber was designed to accommodate two test specimens. A common water recirculation and pressurization system was employed to service two test chambers. Thus, four fatigue crack propagation rate tests could be conducted simultaneously in the pressurized water environment. The data analysis was automated to minimize the typically high labor costs associated with corrosion fatigue crack propagation testing. Verification FCGR tests conducted on an ASTM A469 rotor steel in a room temperature air environment as well as actual PWR environment FCGR tests performed on an ASTM A533 Grade B Class 2 pressure vessel steel demonstrated that the dual specimen test facility is an excellent system for developing the FCGR properties of materials in adverse environments

MP-Division health and safety reference handbook

International Nuclear Information System (INIS)

Putnam, T.M.

1987-09-01

This report presents the objectives, organization, policies, and essential rules and procedures that have been adopted by MP Division and that form the basis of the Health and Safety Program of the Clinton P. Anderson Meson Physics Facility (LAMPF). The facility includes the beam-delivery systems for the Los Alamos Neutron Scattering Center and the Weapons Neutron Research Facility (LANSCE/WNR). The program is designed not only to assure the health and safety of all personnel, including users, in their work at LAMPF, and of MP-Division staff in their work on the LANSCE/WNR beam lines, but also to protect the facility (buildings and equipment) and the environment. 33 refs., 18 figs., 2 tabs

Division of labour in the yeast: Saccharomyces cerevisiae.

Science.gov (United States)

Wloch-Salamon, Dominika M; Fisher, Roberta M; Regenberg, Birgitte

2017-10-01

Division of labour between different specialized cell types is a central part of how we describe complexity in multicellular organisms. However, it is increasingly being recognized that division of labour also plays an important role in the lives of predominantly unicellular organisms. Saccharomyces cerevisiae displays several phenotypes that could be considered a division of labour, including quiescence, apoptosis and biofilm formation, but they have not been explicitly treated as such. We discuss each of these examples, using a definition of division of labour that involves phenotypic variation between cells within a population, cooperation between cells performing different tasks and maximization of the inclusive fitness of all cells involved. We then propose future research directions and possible experimental tests using S. cerevisiae as a model organism for understanding the genetic mechanisms and selective pressures that can lead to the evolution of the very first stages of a division of labour. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

Applied Physics Division 1998 Progress Report

International Nuclear Information System (INIS)

Cecchini, M.; Crescentini, L; Ghezzi, L.; Kent, C.; Bottomei, M.

2001-01-01

This report outlines the 1998 research activities carried out by the Applied Physics Division of the Innovation Department of ENEA (Italian Agency for New Technologies, Energy and Environment). The fields addressed and discussed include: optical and electro-optical technologies (chaps. 1 and 2); accelerator technologies (chap. 3); diagnostic systems for science and engineering (chaps. 4 and 5); theory, modelling and computational methods (chaps. 6 and 7). The aim of the Applied Physics Division is to develop technologies and systems that can be directly applied by internal (ENEA) and external users in research (high-resolution spectroscopy, laser-generated soft-x-ray sources), production processes (laser material photoproduction, structural analysis), social, cultural and environmental sciences (laser remote sensing, modelling of ecosystems and population dynamics) and medicine (particle accelerator for radiotherapy). Most of the work in 1998 was performed by the division's laboratories at the Frascati, Casaccia and Bologna Research Centres of ENEA; some was done elsewhere in collaboration with other ENEA units, external laboratories and industries. A good share of the activities was carried out for international projects; in particular, the IV European Union Framework Program

Applied Physics Division 1998 Progress Report

Energy Technology Data Exchange (ETDEWEB)

Cecchini, M.; Crescentini, L; Ghezzi, L.; Kent, C.; Bottomei, M. [ENEA, Centro Ricerche Frascati, Frascati, RM (Italy). Applied physics Division

1999-07-01

This report outlines the 1998 research activities carried out by the Applied Physics Division of the Innovation Department of ENEA (Italian Agency for New Technologies, Energy and Environment). The fields addressed and discussed include: optical and electro-optical technologies (chaps. 1 and 2); accelerator technologies (chap. 3); diagnostic systems for science and engineering (chaps. 4 and 5); theory, modelling and computational methods (chaps. 6 and 7). The aim of the Applied Physics Division is to develop technologies and systems that can be directly applied by internal (ENEA) and external users in research (high-resolution spectroscopy, laser-generated soft-x-ray sources), production processes (laser material photoproduction, structural analysis), social, cultural and environmental sciences (laser remote sensing, modelling of ecosystems and population dynamics) and medicine (particle accelerator for radiotherapy). Most of the work in 1998 was performed by the division's laboratories at the Frascati, Casaccia and Bologna Research Centres of ENEA; some was done elsewhere in collaboration with other ENEA units, external laboratories and industries. A good share of the activities was carried out for international projects; in particular, the IV European Union Framework Program.

Chemical Technology Division. Annual technical report, 1995

Energy Technology Data Exchange (ETDEWEB)

Laidler, J.J.; Myles, K.M.; Green, D.W.; McPheeters, C.C.

1996-06-01

Highlights of the Chemical Technology (CMT) Division`s activities during 1995 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) methods for treatment of hazardous waste and mixed hazardous/radioactive waste; (3) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (4) processes for separating and recovering selected elements from waste streams, concentrating low-level radioactive waste streams with advanced evaporator technology, and producing {sup 99}Mo from low-enriched uranium; (5) electrometallurgical treatment of different types of spent nuclear fuel in storage at Department of Energy sites; and (6) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems.

An analysis of the job of strength and conditioning coach for football at the Division II level.

Science.gov (United States)

Massey, C Dwayne; Schwind, Justin J; Andrews, Donnie C; Maneval, Mark W

2009-12-01

The purpose of this investigation was to describe the working environment of the heretofore unexamined Division II football strength and conditioning coach (SCC). Data were collected on demographic characteristics, job satisfaction, major job duties and responsibilities, work environment, and professional and personal relationships. A total of 63 questionnaires were returned by the potential 155 institutions identified at the Division II level. Percentages were used in the reporting of data. The results indicate that this group is relatively young (34.1), new to the profession, have low job stability, a low rate of professional certification, make a salary less than their Division I-A counterparts, and assume more duties and responsibilities than their Division I-A colleagues. Despite these apparent drawbacks, by and large, these SCC appeared content with their career choice and circumstances.

Prediction of software operational reliability using testing environment factor

International Nuclear Information System (INIS)

Jung, Hoan Sung

1995-02-01

Software reliability is especially important to customers these days. The need to quantify software reliability of safety-critical systems has been received very special attention and the reliability is rated as one of software's most important attributes. Since the software is an intellectual product of human activity and since it is logically complex, the failures are inevitable. No standard models have been established to prove the correctness and to estimate the reliability of software systems by analysis and/or testing. For many years, many researches have focused on the quantification of software reliability and there are many models developed to quantify software reliability. Most software reliability models estimate the reliability with the failure data collected during the test assuming that the test environments well represent the operation profile. User's interest is on the operational reliability rather than on the test reliability, however. The experiences show that the operational reliability is higher than the test reliability. With the assumption that the difference in reliability results from the change of environment, testing environment factor comprising the aging factor and the coverage factor are defined in this work to predict the ultimate operational reliability with the failure data. It is by incorporating test environments applied beyond the operational profile into testing environment factor Test reliability can also be estimated with this approach without any model change. The application results are close to the actual data. The approach used in this thesis is expected to be applicable to ultra high reliable software systems that are used in nuclear power plants, airplanes, and other safety-critical applications

Fairchild Stratos Division's Type II prototype lockhopper valve: METC Prototype Test Valve No. F-1 prototype lockhopper valve-testing and development project. Static test report

Energy Technology Data Exchange (ETDEWEB)

Goff, D. R.; Cutright, R. L.; Griffith, R. A.; Loomis, R. B.; Maxfield, D. A.; Moritz, R. S.

1981-10-01

METC Prototype Test Valve No. F-1 is a hybrid design, based on a segmented ball termed a visor valve, developed and manufactured by Fairchild Stratos Division under contract to the Department of Energy. The valve uses a visor arm that rotates into position and then translates to seal. This valve conditionally completed static testing at METC with clean gas to pressures of 1600 psig and internal valve temperatures to 600/sup 0/F. External leakage was excessive due to leakage through the stuffing box, purge fittings, external bolts, and other assemblies. The stuffing box was repacked several times and redesigned midway through the testing, but external leakage was still excessive. Internal leakage through the seats, except for a few anomalies, was very low throughout the 2409 cycles of testing. As shown by the low internal leakage, the visor valve concept appears to have potential for lock-hopper valve applications. The problems that are present with METC Prototype Test Valve No. F-1 are in the seals, which are equivalent to the shaft and bonnet seals in standard valve designs. The operating conditions at these seals are well within the capabilities of available seal designs and materials. Further engineering and minor modifications should be able to resolve the problems identified during static testing.

Rocketdyne Division annual site environmental report Santa Susana Field Laboratory and Desoto sites 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-30

This annual report discusses environmental monitoring at two manufacturing and test operations sites operated in the Los Angeles area by the Rocketdyne Division of Rockwell International Corporation (Rocketdyne). These are identified as the Santa Susana Field Laboratory (SSFL) and the DeSoto site. The sites have been used for manufacturing, R&D, engineering, and testing in a broad range of technical fields, primarily rocket engine propulsion and nuclear reactor technology. The DeSoto site essentially comprises office space and light industry with no remaining radiological operations, and has little potential impact on the environment. The SSFL site, because of its large size (2,668 acres), warrants comprehensive monitoring to assure protection of the environment. SSFL consists of four administrative areas used for research, development, and test operations as well as a buffer zone. A portion of Area I and all of Area II are owned by the U.S. Government and assigned to the National Aeronautics and Space Administration (NASA). A portion of Area IV is under option for purchase by the Department of Energy (DOE).

Rocketdyne Division annual site environmental report Santa Susana Field Laboratory and Desoto sites 1995

International Nuclear Information System (INIS)

1996-01-01

This annual report discusses environmental monitoring at two manufacturing and test operations sites operated in the Los Angeles area by the Rocketdyne Division of Rockwell International Corporation (Rocketdyne). These are identified as the Santa Susana Field Laboratory (SSFL) and the DeSoto site. The sites have been used for manufacturing, R ampersand D, engineering, and testing in a broad range of technical fields, primarily rocket engine propulsion and nuclear reactor technology. The DeSoto site essentially comprises office space and light industry with no remaining radiological operations, and has little potential impact on the environment. The SSFL site, because of its large size (2,668 acres), warrants comprehensive monitoring to assure protection of the environment. SSFL consists of four administrative areas used for research, development, and test operations as well as a buffer zone. A portion of Area I and all of Area II are owned by the U.S. Government and assigned to the National Aeronautics and Space Administration (NASA). A portion of Area IV is under option for purchase by the Department of Energy (DOE)

Analysis of Gauntlet Test Performance and Injury Risk in Intercollegiate Division I Female Soccer (Football) Players: A Retrospective Study.

Science.gov (United States)

Ness, Brandon M; Zimney, Kory; Schweinle, William E

2017-11-01

Injury risk factors and relevant assessments have been identified in women's soccer athletes. Other tests assess fitness (eg, the Gauntlet Test [GT]). However, little empirical support exists for the utility of the GT to predict time loss injury. To examine the GT as a predictor of injury in intercollegiate Division I female soccer athletes. Retrospective, nonexperimental descriptive cohort study. College athletic facilities. 71 female Division I soccer athletes (age 19.6 ± 1.24 y, BMI 23.0 ± 2.19). GT, demographic, and injury data were collected over 3 consecutive seasons. GT trials were administered by coaching staff each preseason. Participation in team-based activities (practices, matches) was restricted until a successful GT trial. Soccer-related injuries that resulted in time loss from participation were recorded. 71 subjects met the inclusion criteria, with 12 lower body time loss injuries sustained. Logistic regression models indicated that with each unsuccessful GT attempt, the odds of sustaining an injury increased by a factor of 3.5 (P soccer athletes in this cohort. Further investigation into the appropriate application of the GT for injury prediction is warranted given the scope of this study.

Transportation environment data bank index

International Nuclear Information System (INIS)

Davidson, C.A.; Foley, J.T.

1976-02-01

In an effort to determine the environment intensities to which shipping containers will be exposed, a ''Data Bank'' of environmental information has been established by Sandia Laboratories, Division 1285 for the ERDA Division of Environmental Control Technology. This document is an index which can be used to request data of interest

Star Excursion Balance Test Anterior Asymmetry Is Associated With Injury Status in Division I Collegiate Athletes.

Science.gov (United States)

Stiffler, Mikel R; Bell, David R; Sanfilippo, Jennifer L; Hetzel, Scott J; Pickett, Kristen A; Heiderscheit, Bryan C

2017-05-01

Study Design Retrospective cohort. Background Star Excursion Balance Test (SEBT) performance differs by sport in healthy collegiate athletes, and lower extremity injury rates also vary by sport, sex, and athletic exposure. The relationship between SEBT performance and injury risk has not been evaluated with consideration of these additional variables, which may be necessary to fully describe the relationship between SEBT performance and injury risk. Objectives To assess the association between preseason SEBT performance and noncontact injury occurrence to the knee or ankle in Division I collegiate athletes when controlling for sport, sex, and athletic exposure. Methods Star Excursion Balance Test performance, starting status, and injury status were reviewed retrospectively in National Collegiate Athletic Association Division I collegiate athletes from a single institution. A total of 147 athletes were healthy at the time of preseason SEBT testing and either remained healthy (n = 118) or sustained a noncontact injury to the knee or ankle (n = 29) during their sport's subsequent competitive season. Side-to-side asymmetries were calculated in each direction as the absolute difference in reach distance between limbs. Star Excursion Balance Test reach distances and asymmetries were compared between groups using multivariable regression, controlling for sport, sex, and athletic exposure (starter, nonstarter). Receiver operating characteristic curves were used to determine optimal sensitivity and specificity for significant models. Results When controlling for sport, sex, and athletic exposure, SEBT side-to-side asymmetry in the anterior direction, expressed as an absolute or normalized to limb length, discriminated between injured and noninjured athletes (area under the curve greater than 0.82). Conclusion Assessing side-to-side reach asymmetry in the anterior direction of the SEBT may assist in identifying collegiate athletes who are at risk for sustaining noncontact

Transportation Environment Data Bank index

International Nuclear Information System (INIS)

Davidson, C.A.; Foley, J.T.

1977-04-01

In an effort to determine the environment intensities to which energy materials in transit will be exposed, a ''Data Bank'' of environmental information has been established by Sandia Laboratories, Division 1285 for the ERDA Division of Environmental Control Technology. This document is an index which can be used to request data of interest

Progress report, Health Sciences Division, 1 October - 31 December, 1981

International Nuclear Information System (INIS)

1982-03-01

The work of the Health Sciences Division during the quarter included development of improved radiation counters and dosimeters, studies of radionuclide migration through the environment, investigations of the effects of radiation upon a variety of living organisms, and calculation of improved dosimetry factors

Chemical Technology Division annual technical report, 2001

International Nuclear Information System (INIS)

Lewis, D.; Gay, E. C.; Miller, J. C.; Boparai, A. S.

2002-01-01

The Chemical Technology Division (CMT) is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. CMT is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory and Environment, Safety, and Health Analytical Chemistry services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature superconductors

Liquid salt environment stress-rupture testing

Science.gov (United States)

Ren, Weiju; Holcomb, David E.; Muralidharan, Govindarajan; Wilson, Dane F.

2016-03-22

Disclosed herein are systems, devices and methods for stress-rupture testing selected materials within a high-temperature liquid salt environment. Exemplary testing systems include a load train for holding a test specimen within a heated inert gas vessel. A thermal break included in the load train can thermally insulate a load cell positioned along the load train within the inert gas vessel. The test specimen can include a cylindrical gage portion having an internal void filled with a molten salt during stress-rupture testing. The gage portion can have an inner surface area to volume ratio of greater than 20 to maximize the corrosive effect of the molten salt on the specimen material during testing. Also disclosed are methods of making a salt ingot for placement within the test specimen.

LASER SPECTROSCOPY AND TRACE ELEMENT ANALYSIS Chapter from the Energy and Environment Division Annual Report 1980

Energy Technology Data Exchange (ETDEWEB)

Various, Authors

1981-05-01

In order to control pollutants resulting from energy production and utilization, adequate methods are required for monitoring the level of various substances often present at low concentrations. The Energy and Environment Division Applied Research in Laser Spectroscopy & Analytical Techniques Program is directed toward meeting these needs, Emphasis is on the development of physical methods, as opposed to conventional chemical analysis techniques. The advantages, now widely recognized, include ultra-high sensitivity coupled with minimal sample preparation. In some instances physical methods provide multi-parameter measurements which often provide the only means of achiev·ing the sensitivity necessary for the detection of trace contaminants. Work is reported in these areas: APPLIED PHYSICS AND LASER SPECTROSCOPY RESEARCH; MICROPROCESSOR CONTROLLER ANODIC STRIPPING VOLTAMETER FOR TRACE METALS ANALYSIS IN WATER; THE SURVEY OF INSTRUMENTATION FOR ENVIRONMENTAL MONITORING; THE POSSIBLE CHRONDRITIC NATURE OF THE DANISH CRETACEOUS~TERTIARY BOUNDARY; IMPROVEMENT OF THE SENSITIVITY AND PRECISION OF NEUTRON ACTIVATION ANALYSIS OF SOME ELEMENTS IN PLANKTON AND PLANKTONIC FISH; and SOURCES OF SOME SECONDARILY WORKED OBSIDIAN ARTIFACTS FROM TIKAL, GUATEMALA.

Computational Fair Division

DEFF Research Database (Denmark)

Branzei, Simina

Fair division is a fundamental problem in economic theory and one of the oldest questions faced through the history of human society. The high level scenario is that of several participants having to divide a collection of resources such that everyone is satisfied with their allocation -- e.g. two...... heirs dividing a car, house, and piece of land inherited. The literature on fair division was developed in the 20th century in mathematics and economics, but computational work on fair division is still sparse. This thesis can be seen as an excursion in computational fair division divided in two parts....... The first part tackles the cake cutting problem, where the cake is a metaphor for a heterogeneous divisible resource such as land, time, mineral deposits, and computer memory. We study the equilibria of classical protocols and design an algorithmic framework for reasoning about their game theoretic...

Conservatism implications of shock test tailoring for multiple design environments

Science.gov (United States)

Baca, Thomas J.; Bell, R. Glenn; Robbins, Susan A.

1987-01-01

A method for analyzing shock conservation in test specifications that have been tailored to qualify a structure for multiple design environments is discussed. Shock test conservation is qualified for shock response spectra, shock intensity spectra and ranked peak acceleration data in terms of an Index of Conservation (IOC) and an Overtest Factor (OTF). The multi-environment conservation analysis addresses the issue of both absolute and average conservation. The method is demonstrated in a case where four laboratory tests have been specified to qualify a component which must survive seven different field environments. Final judgment of the tailored test specification is shown to require an understanding of the predominant failure modes of the test item.

On infinitely divisible semimartingales

DEFF Research Database (Denmark)

Basse-O'Connor, Andreas; Rosiński, Jan

2015-01-01

to non Gaussian infinitely divisible processes. First we show that the class of infinitely divisible semimartingales is so large that the natural analog of Stricker's theorem fails to hold. Then, as the main result, we prove that an infinitely divisible semimartingale relative to the filtration generated...... by a random measure admits a unique decomposition into an independent increment process and an infinitely divisible process of finite variation. Consequently, the natural analog of Stricker's theorem holds for all strictly representable processes (as defined in this paper). Since Gaussian processes...... are strictly representable due to Hida's multiplicity theorem, the classical Stricker's theorem follows from our result. Another consequence is that the question when an infinitely divisible process is a semimartingale can often be reduced to a path property, when a certain associated infinitely divisible...

Has the "Equal Environments" assumption been tested in twin studies?

Science.gov (United States)

Eaves, Lindon; Foley, Debra; Silberg, Judy

2003-12-01

A recurring criticism of the twin method for quantifying genetic and environmental components of human differences is the necessity of the so-called "equal environments assumption" (EEA) (i.e., that monozygotic and dizygotic twins experience equally correlated environments). It has been proposed to test the EEA by stratifying twin correlations by indices of the amount of shared environment. However, relevant environments may also be influenced by genetic differences. We present a model for the role of genetic factors in niche selection by twins that may account for variation in indices of the shared twin environment (e.g., contact between members of twin pairs). Simulations reveal that stratification of twin correlations by amount of contact can yield spurious evidence of large shared environmental effects in some strata and even give false indications of genotype x environment interaction. The stratification approach to testing the equal environments assumption may be misleading and the results of such tests may actually be consistent with a simpler theory of the role of genetic factors in niche selection.

Towards a Development Environment for Model Based Test Design

OpenAIRE

Jing, Han

2008-01-01

Within the UP IP I&V organization there is high focus on increasing the ability to predict product quality in a cost efficient way. Test automation has therefore been an important enabler for us. The IP test design environment is continuously evolving and the investigations will show which improvements that is most important to implement in short and long term. In Ericsson UP IP I&V, the test automation framework environments are severed to complete some process by automated method, f...

Environmental Sciences Division annual progress report for period ending September 30, 1991

Energy Technology Data Exchange (ETDEWEB)

1992-04-01

This progress report summarizes the research and development activities conducted in the Environmental Sciences Division of Oak Ridge National Laboratory during the period October 1, 1990, through September 30, 1991. The report is structured to provide descriptions of current activities and accomplishments in each of the division`s major organizational units. Following the sections describing the organizational units is a section devoted to lists of information necessary to convey the scope of the work in the division. The Environmental Sciences Division (ESD) at Oak Ridge National Laboratory (ORNL) conducts environmental research and analyses associated with both energy technology development and the interactions between people and the environment. The division engages in basic and applied research for a diverse list of sponsors. While the US Department of Energy (DOE) is the primary sponsor ESD staff also perform research for other federal agencies, state agencies, and private industry. The division works collaboratively with federal agencies, universities, and private organizations in achieving its research objectives and hosts a large number of visiting investigators from these organizations. Given the diverse interdisciplinary specialization of its staff, ESD provides technical expertise on complex environmental problems and renders technical leadership for major environmental issues of national and local concern. This progress report highlights many of ESD`s accomplishment in these and other areas in FY 1991.

MP-Division health and safety reference handbook. [Contains glossary

Energy Technology Data Exchange (ETDEWEB)

Putnam, T.M.

1987-09-01

This report presents the objectives, organization, policies, and essential rules and procedures that have been adopted by MP Division and that form the basis of the Health and Safety Program of the Clinton P. Anderson Meson Physics Facility (LAMPF). The facility includes the beam-delivery systems for the Los Alamos Neutron Scattering Center and the Weapons Neutron Research Facility (LANSCE/WNR). The program is designed not only to assure the health and safety of all personnel, including users, in their work at LAMPF, and of MP-Division staff in their work on the LANSCE/WNR beam lines, but also to protect the facility (buildings and equipment) and the environment. 33 refs., 18 figs., 2 tabs.

Modeling of Complex Life Cycle Prediction Based on Cell Division

Directory of Open Access Journals (Sweden)

Fucheng Zhang

2017-01-01

Full Text Available Effective fault diagnosis and reasonable life expectancy are of great significance and practical engineering value for the safety, reliability, and maintenance cost of equipment and working environment. At present, the life prediction methods of the equipment are equipment life prediction based on condition monitoring, combined forecasting model, and driven data. Most of them need to be based on a large amount of data to achieve the problem. For this issue, we propose learning from the mechanism of cell division in the organism. We have established a moderate complexity of life prediction model across studying the complex multifactor correlation life model. In this paper, we model the life prediction of cell division. Experiments show that our model can effectively simulate the state of cell division. Through the model of reference, we will use it for the equipment of the complex life prediction.

Energy and Environmental Systems Division's publications publications 1968-1982

Energy Technology Data Exchange (ETDEWEB)

None

1982-03-01

Books, journal articles, conference papers, and technical reports produced by the Energy and Environmental Systems Division of Argonne National Laboratory are listed in this bibliography. Subjects covered are energy resources (recovery and use); energy-efficient technology; electric utilities, and environments. (MCW)

Germ cells may survive clipping and division of the spermatic vessels in surgery for intra-abdominal testes

DEFF Research Database (Denmark)

Thorup, J M; Cortes, D; Visfeldt, J

1999-01-01

PURPOSE: Laparoscopy is a well described modality that provides an accurate visual diagnosis upon which further management of intra-abdominal testes may be based. Laparoscopic ligation of spermatic vessels as stage 1 of the procedure is a natural extension of laparoscopy. A staged approach provides...... studied 17 nonpalpable testes in 10 patients 1 year and 7 months to 13(1/2) years old. Results of testicular biopsies of 13 intra-abdominal testes taken at stages 1 and 2 of surgery were available for histological comparison. RESULTS: Median number of spermatogonia per tubular cross section...... of the biopsies taken at stage 2 was slightly lower (0.03) compared to the median number at stage 1 (0.06) of the operation but this difference was not significant (p = 0.2031). CONCLUSIONS: Our study shows that the spermatogonia may survive clipping and division of the spermatic vessels, although the number...

Division of Finance Homepage

Science.gov (United States)

Top Department of Administration logo Alaska Department of Administration Division of Finance Search Search the Division of Finance site DOF State of Alaska Finance Home Content Area Accounting Charge Cards You are here Administration / Finance Division of Finance Updates IRIS Expenditure Object Codes

Biennial activity report of Metallurgy Division for 1989 and 1990

International Nuclear Information System (INIS)

Kamachi Mudali, U.; Muraleedharan, P.; Parameswaran, P.; Swaminathan, K.; Sreedharan, O.M.

1993-01-01

This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor

Robust Tests for Additive Gene-Environment Interaction in Case-Control Studies Using Gene-Environment Independence

DEFF Research Database (Denmark)

Liu, Gang; Lee, Seunggeun; Lee, Alice W

2018-01-01

test with case-control data. Our simulation studies suggest that the EB approach uses the gene-environment independence assumption in a data-adaptive way and provides power gain compared to the standard logistic regression analysis and better control of Type I error when compared to the analysis......There have been recent proposals advocating the use of additive gene-environment interaction instead of the widely used multiplicative scale, as a more relevant public health measure. Using gene-environment independence enhances the power for testing multiplicative interaction in case......-control studies. However, under departure from this assumption, substantial bias in the estimates and inflated Type I error in the corresponding tests can occur. This paper extends the empirical Bayes (EB) approach previously developed for multiplicative interaction that trades off between bias and efficiency...

Materials and Components Technology Division research summary, 1992

International Nuclear Information System (INIS)

1992-11-01

The Materials and Components Technology Division (MCT) provides a research and development capability for the design, fabrication, and testing of high-reliability materials, components, and instrumentation. Current divisional programs related to nuclear energy support the development of the Integral Fast Reactor (IFR): life extension and accident analyses for light water reactors (LWRs); fuels development for research and test reactors; fusion reactor first-wall and blanket technology; and safe shipment of hazardous materials. MCT Conservation and Renewables programs include major efforts in high-temperature superconductivity, tribology, nondestructive evaluation (NDE), and thermal sciences. Fossil Energy Programs in MCT include materials development, NDE technology, and Instrumentation design. The division also has a complementary instrumentation effort in support of Arms Control Technology. Individual abstracts have been prepared for the database

Cell Division Synchronization

Science.gov (United States)

The report summarizes the progress in the design and construction of automatic equipment for synchronizing cell division in culture by periodic...Concurrent experiments in hypothermic synchronization of algal cell division are reported.

Chemical Technology Division, Annual technical report, 1991

Energy Technology Data Exchange (ETDEWEB)

1992-03-01

Highlights of the Chemical Technology (CMT) Division`s activities during 1991 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion and coal-fired magnetohydrodynamics; (3) methods for treatment of hazardous and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources; chemistry of superconducting oxides and other materials of interest with technological application; interfacial processes of importance to corrosion science, catalysis, and high-temperature superconductivity; and the geochemical processes involved in water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL).

Physics Division progress report, January 1, 1991--December 31, 1991

International Nuclear Information System (INIS)

Shera, E.B.; Hollen, G.Y.

1992-06-01

This report provides selected accounts of significant progress in research and development achieved by Physics Division personnel during the period January 1, 1991, through December 31, 1991. It also provides a general description of the goals and interests of the Division, very brief descriptions of projects in the Division, and a list of publications produced during this period. The report represents the three main areas of experimental research and development in which the Physics Division serves the needs of Los Alamos National Laboratory and the nation in defense and basic sciences: (1) fundamental research in nuclear and particle physics, condensed-matter physics, and biophysics; (2) laser physics and applications, especially to high-density plasmas; (3) defense physics, including the development of diagnostic methods for weapons tests, weapons-related high energy-density physics, and other programs

Argonne Physics Division Colloquium

Science.gov (United States)

[Argonne Logo] [DOE Logo] Physics Division Home News Division Information Contact PHY Org Chart Physics Division Colloquium Auditorium, Building 203, Argonne National Laboratory Fridays at 11:00 AM 2017 : Sereres Johnston 15 Sep 2017 Joint Physics and Materials Science Colloquium J. C. Séamus Davis, Cornell

Comparison of chosen physical fitness characteristics of Turkish professional basketball players by division and playing position.

Science.gov (United States)

Köklü, Yusuf; Alemdaroğlu, Utku; Koçak, Fatma Ünver; Erol, A Emre; Fındıkoğlu, Gülin

2011-12-01

The purpose of the present study was to compare chosen physical fitness characteristics of Turkish professional basketball players in different divisions (first and second division) and playing positions. Forty-five professional male basketball players (14 guards, 15 forwards, 16 centers) participated in this study voluntarily. For each player, anthropometric measurements were performed, as well as a multi-stage 20 m shuttle run, isokinetic leg strength, squat jump (SJ), countermovement jump (CMJ), 10-30 meter single-sprint and T-drill agility tests. The differences in terms of division were evaluated by independent t-test and the differences by playing position were evaluated by one-way ANOVA with Post Hoc Tukey test. First division players' CMJ measurements were significantly higher than those of second division players' (p≤0.05), whereas second division players' 10 m sprint times were significantly better than those of first division players' (p≤0.05). In addition, forwards and centers were significantly taller than guards. Centers were significantly heavier and their T-drill test performances were inferior to those of forwards and guards (p≤0.05). Moreover, guards had a significantly higher maximal oxygen uptake (VO2 max) than centers. Guards and forwards showed significantly better performance in the 10 and 30 m sprint tests than centers (p≤0.05). Forwards and centers had significantly better left leg flexor strength at 180°.s(-1)(p≤0.05). In conclusion, the findings of the present study indicated that physical performance of professional basketball players differed among guards, forwards and centers, whereas there were not significant differences between first and second division players. According to the present study, court positions have different demands and physical attributes which are specific to each playing position in professional basketball players. Therefore, these results suggest that coaches should tailor fitness programs according to

INO80 Chromatin Remodeling Coordinates Metabolic Homeostasis with Cell Division

Directory of Open Access Journals (Sweden)

Graeme J. Gowans

2018-01-01

Full Text Available Adaptive survival requires the coordination of nutrient availability with expenditure of cellular resources. For example, in nutrient-limited environments, 50% of all S. cerevisiae genes synchronize and exhibit periodic bursts of expression in coordination with respiration and cell division in the yeast metabolic cycle (YMC. Despite the importance of metabolic and proliferative synchrony, the majority of YMC regulators are currently unknown. Here, we demonstrate that the INO80 chromatin-remodeling complex is required to coordinate respiration and cell division with periodic gene expression. Specifically, INO80 mutants have severe defects in oxygen consumption and promiscuous cell division that is no longer coupled with metabolic status. In mutant cells, chromatin accessibility of periodic genes, including TORC1-responsive genes, is relatively static, concomitant with severely attenuated gene expression. Collectively, these results reveal that the INO80 complex mediates metabolic signaling to chromatin to restrict proliferation to metabolically optimal states.

Divisible ℤ-modules

Directory of Open Access Journals (Sweden)

Futa Yuichi

2016-03-01

Full Text Available In this article, we formalize the definition of divisible ℤ-module and its properties in the Mizar system [3]. We formally prove that any non-trivial divisible ℤ-modules are not finitely-generated.We introduce a divisible ℤ-module, equivalent to a vector space of a torsion-free ℤ-module with a coefficient ring ℚ. ℤ-modules are important for lattice problems, LLL (Lenstra, Lenstra and Lovász base reduction algorithm [15], cryptographic systems with lattices [16] and coding theory [8].

Characterization of dependencies between growth and division in budding yeast.

Science.gov (United States)

Mayhew, Michael B; Iversen, Edwin S; Hartemink, Alexander J

2017-02-01

Cell growth and division are processes vital to the proliferation and development of life. Coordination between these two processes has been recognized for decades in a variety of organisms. In the budding yeast Saccharomyces cerevisiae , this coordination or 'size control' appears as an inverse correlation between cell size and the rate of cell-cycle progression, routinely observed in G 1 prior to cell division commitment. Beyond this point, cells are presumed to complete S/G 2 /M at similar rates and in a size-independent manner. As such, studies of dependence between growth and division have focused on G 1 Moreover, in unicellular organisms, coordination between growth and division has commonly been analysed within the cycle of a single cell without accounting for correlations in growth and division characteristics between cycles of related cells. In a comprehensive analysis of three published time-lapse microscopy datasets, we analyse both intra- and inter-cycle dependencies between growth and division, revisiting assumptions about the coordination between these two processes. Interestingly, we find evidence (i) that S/G 2 /M durations are systematically longer in daughters than in mothers, (ii) of dependencies between S/G 2 /M and size at budding that echo the classical G 1 dependencies, and (iii) in contrast with recent bacterial studies, of negative dependencies between size at birth and size accumulated during the cell cycle. In addition, we develop a novel hierarchical model to uncover inter-cycle dependencies, and we find evidence for such dependencies in cells growing in sugar-poor environments. Our analysis highlights the need for experimentalists and modellers to account for new sources of cell-to-cell variation in growth and division, and our model provides a formal statistical framework for the continued study of dependencies between biological processes. © 2017 The Author(s).

Implementation of a control system test environment in UNIX

International Nuclear Information System (INIS)

Brittain, C.R.; Otaduy, P.J.; Rovere, L.A.

1990-01-01

This paper discusses how UNIX features such as shared memory, remote procedure calls, and signalling have been used to implement a distributed computational environment ideal for the development and testing of digital control systems. The resulting environment -based on features commonly available in commercial workstations- is flexible, allows process simulation and controller development to proceed in parallel, and provides for testing and validation in a realistic environment. In addition, the use of shared memory to exchange data allows other tasks such as user interfaces and recorders to be added without affecting the process simulation or controllers. A library of functions is presented which provides a simple interface to using the features described. These functions can be used in either C or FORTRAN programs and have been tested on a network of Sun workstations and an ENCORE parallel computer. 6 refs., 2 figs

Thermosyphon Flooding in Reduced Gravity Environments Test Results

Science.gov (United States)

Gibson, Marc A.; Jaworske, Donald A.; Sanzi, Jim; Ljubanovic, Damir

2013-01-01

The condenser flooding phenomenon associated with gravity aided two-phase thermosyphons was studied using parabolic flights to obtain the desired reduced gravity environment (RGE). The experiment was designed and built to test a total of twelve titanium water thermosyphons in multiple gravity environments with the goal of developing a model that would accurately explain the correlation between gravitational forces and the maximum axial heat transfer limit associated with condenser flooding. Results from laboratory testing and parabolic flights are included in this report as part I of a two part series. The data analysis and correlations are included in a follow on paper.

Fusion Energy Division progress report, 1 January 1990--31 December 1991

Energy Technology Data Exchange (ETDEWEB)

Sheffield, J.; Baker, C.C.; Saltmarsh, M.J.

1994-03-01

The Fusion Program of the Oak Ridge National Laboratory (ORNL), a major part of the national fusion program, encompasses nearly all areas of magnetic fusion research. The program is directed toward the development of fusion as an economical and environmentally attractive energy source for the future. The program involves staff from ORNL, Martin Marietta Energy systems, Inc., private industry, the academic community, and other fusion laboratories, in the US and abroad. Achievements resulting from this collaboration are documented in this report, which is issued as the progress report of the ORNL Fusion Energy Division; it also contains information from components for the Fusion Program that are external to the division (about 15% of the program effort). The areas addressed by the Fusion Program include the following: experimental and theoretical research on magnetic confinement concepts; engineering and physics of existing and planned devices, including remote handling; development and testing of diagnostic tools and techniques in support of experiments; assembly and distribution to the fusion community of databases on atomic physics and radiation effects; development and testing of technologies for heating and fueling fusion plasmas; development and testing of superconducting magnets for containing fusion plasmas; development and testing of materials for fusion devices; and exploration of opportunities to apply the unique skills, technology, and techniques developed in the course of this work to other areas (about 15% of the Division`s activities). Highlights from program activities during 1990 and 1991 are presented.

Chemical Technology Division annual technical report, 2001

International Nuclear Information System (INIS)

Lewis, D.; Gay, E. C.; Miller, J. C.; Boparai, A. S.

2002-01-01

The Chemical Technology Division (CMT) is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. CMT is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory and Environment, Safety, and Health Analytical Chemistry services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature super-conductors. The Division's wide-ranging expertise finds ready application in solving energy and environmental problems. Division personnel are frequently called on by governmental and industrial

Biennial activity report of Metallurgy Division for 1989 and 1990

Energy Technology Data Exchange (ETDEWEB)

Kamachi Mudali, U; Muraleedharan, P; Parameswaran, P; Swaminathan, K; Sreedharan, O M [eds.; Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

1994-12-31

This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor 7 figs., 6 tabs., 2 ills.

Physics Division progress report, January 1, 1990--December 31, 1990

International Nuclear Information System (INIS)

Shera, E.B.; Hollen, G.Y.

1991-07-01

This report provides selected accounts of significant progress in research and development achieved by Physics Division personnel during the period January 1, 1990, through December 31, 1990. It also provides a general description of the goals and interests of the Division, very brief descriptions of projects in the Division, and a list of publications produced during this period. The report represents the three main areas of experimental research and development in which the Physics Division serves the needs of Los Alamos National Laboratory and the nation in defense and basic sciences: (1) fundamental research in nuclear and particle physics, condensed-matter physics, and biophysics; (2) laser physics and applications, especially to high-density plasmas; and (3) defense physics, including the development of diagnostic methods for weapons tests, weapons-related high energy-density physics, and programs supporting the Strategic Defense Initiative

Reactor Division semestrial progress report January - June 1987

International Nuclear Information System (INIS)

1987-01-01

This report covers the activities of the reactor division at the SCK-CEN during the first semester of 1987. It deals with the BR-2 materials testing reactor, the BR-3 power plant, reactor physics, water cooled reactors, fast neutron reactors, fusion, non nuclear programmes, testing and commissioning, high and medium activities, and informatics. (MCB)

Reactor Division semestrial progress report July - December 1987

International Nuclear Information System (INIS)

1987-01-01

This report covers the activities of the reactor division at the SCK-CEN during the second semester of 1987. It deals with the BR-2 materials testing reactor, the BR-3 power plant, reactor physics, water cooled reactors, fast neutron reactors, fusion, non nuclear programmes, testing and commissioning, high and medium activities, and informatics. (MCB)

Prediction of software operational reliability using testing environment factors

International Nuclear Information System (INIS)

Jung, Hoan Sung; Seong, Poong Hyun

1995-01-01

A number of software reliability models have been developed to estimate and to predict software reliability. However, there are no established standard models to quantify software reliability. Most models estimate the quality of software in reliability figures such as remaining faults, failure rate, or mean time to next failure at the testing phase, and they consider them ultimate indicators of software reliability. Experience shows that there is a large gap between predicted reliability during development and reliability measured during operation, which means that predicted reliability, or so-called test reliability, is not operational reliability. Customers prefer operational reliability to test reliability. In this study, we propose a method that predicts operational reliability rather than test reliability by introducing the testing environment factor that quantifies the changes in environments

Environmental Sciences Division annual progress report for period ending September 30, 1991

Energy Technology Data Exchange (ETDEWEB)

1992-04-01

This progress report summarizes the research and development activities conducted in the Environmental Sciences Division of Oak Ridge National Laboratory during the period October 1, 1990, through September 30, 1991. The report is structured to provide descriptions of current activities and accomplishments in each of the division's major organizational units. Following the sections describing the organizational units is a section devoted to lists of information necessary to convey the scope of the work in the division. The Environmental Sciences Division (ESD) at Oak Ridge National Laboratory (ORNL) conducts environmental research and analyses associated with both energy technology development and the interactions between people and the environment. The division engages in basic and applied research for a diverse list of sponsors. While the US Department of Energy (DOE) is the primary sponsor ESD staff also perform research for other federal agencies, state agencies, and private industry. The division works collaboratively with federal agencies, universities, and private organizations in achieving its research objectives and hosts a large number of visiting investigators from these organizations. Given the diverse interdisciplinary specialization of its staff, ESD provides technical expertise on complex environmental problems and renders technical leadership for major environmental issues of national and local concern. This progress report highlights many of ESD's accomplishment in these and other areas in FY 1991.

Test and analysis of indoor environment of dormitories of universities in autumn

Science.gov (United States)

Chen, Shijia

2017-03-01

In this paper, the indoor thermal and humid environment, luminous environment and acoustic environment of college dormitories in Baoding are tested and conducted a questionnaire survey. From the test, the subjective feelings and the objective evaluation parameters of the students in the dormitory were obtained. At last, the differences of thermal comfort, luminous environment and acoustic environment caused by students' different living habits and adaptability were analyzed.

Process mapping and sequencing in production management: the case of the E and P HSEQ (Health, Safety, Environment and Quality) Division of Repsol YPF Brazil

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Paulo Roberto dos Santos; Silva, Douglas Resende Teixeira da [Repsol YPF Brasil S.A. - UN E and P (Brazil); Moyano, Ignacio Sanchez [Universidad Politecnica de Madrid (Spain); Ferreira Filho, Virgilio Jose Martins [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

One of the main objectives of company's top executives is the optimization of production processes, and process mapping is usually the starting point to reach that goal. As a part of the active effort that Repsol YPF Brazil is making to achieve the optimization of its processes, the company intends to develop a process planning and scheduling management tool for its Exploration and Production (E and P) division, which has recently accomplished the process mapping of its exploration activities. The process mapping was done to make possible in the future a standardization of the exploration activities of the company worldwide, without getting into specific management details for every single process. The present work intends to make progress in the development of the E and P process management plan through the operational expertise of the Health, Safety, Environment and Quality (HSEQ) division of Repsol YPF Brazil. It proposes an initial process management model for the E and P HSEQ activities, which should be eventually expanded for the remaining mapped processes. (author)

Annual report of the Division of High Temperature Engineering

International Nuclear Information System (INIS)

1982-10-01

Research activities conducted in the Division of High Temperature Engineering during fiscal 1981 are described. R and D works of our division are mainly related to a multi-purpose very high-temperature gas-cooled reactor (VHTR) and a fusion reactor. This report deals with the main results obtained on material test, development of computer codes, heat transfer, fluid-dynamics, structural mechanics and the construction of an M + A (Mother and Adapter) section of a HENDEL (Helium Engineering Demonstration Loop) as well. (author)

Progress report: 1996 Radiation Safety Systems Division

International Nuclear Information System (INIS)

Bhagwat, A.M.; Sharma, D.N.; Abani, M.C.; Mehta, S.K.

1997-01-01

The activities of Radiation Safety Systems Division include (i) development of specialised monitoring systems and radiation safety information network, (ii) radiation hazards control at the nuclear fuel cycle facilities, the radioisotope programmes at Bhabha Atomic Research Centre (BARC) and for the accelerators programme at BARC and Centre for Advanced Technology (CAT), Indore. The systems on which development and upgradation work was carried out during the year included aerial gamma spectrometer, automated environment monitor using railway network, radioisotope package monitor and air monitors for tritium and alpha active aerosols. Other R and D efforts at the division included assessment of risk for radiation exposures and evaluation of ICRP 60 recommendations in the Indian context, shielding evaluation and dosimetry for the new upcoming accelerator facilities and solid state nuclear track detector techniques for neutron measurements. The expertise of the divisional members was provided for 36 safety committees of BARC and Atomic Energy Regulatory Board (AERB). Twenty three publications were brought out during the year 1996. (author)

Driver License, Permit, and State ID, Division of Motor Vehicles,

Science.gov (United States)

Skills) Tests Road Test Information Schedule a Road Test Online Business Partners Driving Schools Classes Administration DivisIon of Motor Vehicles Search Minimize Menu DMV Home DMV Home Page Online Services Forms Public Notices Offices DMV Office Locations and Hours DMV Office Wait Times Business Partners Driving

Experimental Facilities Division/User Program Division technical progress report 1999-2000

International Nuclear Information System (INIS)

2001-01-01

In October 1999, the two divisions of the Advanced Photon Source (APS), the Accelerator Systems Division (ASD) and the Experimental Facilities Division (XFD), were reorganized into four divisions (see high-level APS organizational chart, Fig. 1.1). In addition to ASD and XFD, two new divisions were created, the APS Operations Division (AOD), to oversee APS operations, and the User Program Division (UPD), to serve the APS user community by developing and maintaining the highest quality user technical and administration support. Previous XFD Progress Reports (ANL/APS/TB-30 and ANL/APS/TB-34) covered a much broader base, including APS user administrative support and what was previously XFD operations (front ends, interlocks, etc.) This Progress Report summarizes the main scientific and technical activities of XFD, and the technical support, research and development (R and D) activities of UPD from October 1998 through November 2000. The report is divided into four major sections, (1) Introduction, (2) SRI-CAT Beamlines, Technical Developments, and Scientific Applications, (3) User Technical Support, and (4) Major Plans for the Future. Sections 2 and 3 describe the technical activities and research accomplishments of the XFD and UPD personnel in supporting the synchrotron radiation instrumentation (SRI) collaborative access team (CAT) and the general APS user community. Also included in this report is a comprehensive list of publications (Appendix 1) and presentations (Appendix 2) by XFD and UPD staff during the time period covered by this report. The organization of section 2, SRI CAT Beamlines, Technical Developments, and Scientific Applications has been made along scientific techniques/disciplines and not ''geographical'' boundaries of the sectors in which the work was performed. Therefore items under the subsection X-ray Imaging and Microfocusing could have been (and were) performed on several different beamlines by staff in different divisions. The management of

Division of atomic physics

International Nuclear Information System (INIS)

Kroell, S.

1994-01-01

The Division of Atomic Physics, Lund Institute of Technology (LTH), is responsible for the basic physics teaching in all subjects at LTH and for specialized teaching in Optics, Atomic Physics, Atomic and Molecular Spectroscopy and Laser Physics. The Division has research activities in basic and applied optical spectroscopy, to a large extent based on lasers. It is also part of the Physics Department, Lund University, where it forms one of eight divisions. Since the beginning of 1980 the research activities of our division have been centred around the use of lasers. The activities during the period 1991-1992 is described in this progress reports

Chemical Technology Division annual technical report, 1985

International Nuclear Information System (INIS)

1986-04-01

Highlights of the Chemical Technology (CMT) Division's activities during 1985 are presented. In this period, CMT conducted research and development in areas that include the following: (1) advanced batteries - mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) advanced fuel cells with molten carbonate or solid oxide electrolytes; (3) corrosion-protective coatings for high-strength steel; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (5) methodologies for recovery of energy from municipal waste; (6) nuclear technology related to waste management, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor, and proof of breeding in a light water breeder reactor; and (7) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of catalytic hydrogenation and catalytic oxidation; materials chemistry for associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, surface science, and catalysis; the thermochemistry of zeolites and related silicates; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL

Chemical Technology Division annual technical report, 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

Highlights of the Chemical Technology (CMT) Division`s activities during 1994 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion; (3) methods for treatment of hazardous waste and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from waste streams, concentrating radioactive waste streams with advanced evaporator technology, and producing {sup 99}Mo from low-enriched uranium for medical applications; (6) electrometallurgical treatment of the many different types of spent nuclear fuel in storage at Department of Energy sites; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, molecular sieve structures, and impurities in scrap copper and steel; and the geochemical processes involved in mineral/fluid interfaces and water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL).

A decade of Radiometallurgy Division

International Nuclear Information System (INIS)

Ganguly, C.; Bahl, J.K.

1988-12-01

The main thrust of the Research and Development (R and D) activities of the Radiometallurgy Division of the Bhabha Atomic Research Centre is on (1) R and D work and production of plutonium bearing nuclear fuels, (2) Post-Irradiation Examination (PIE) of fuels and structural materials, and (3) failure analysis of power reactor components. The main activities and achievements of the Division during the decade beginning from April 1978 are highlighted and the new thrust areas oriented towards installing a series of 235 MWe and 500 MWe PHWR units and prototype fast breeder reactor (PFBR) of 500 MWe capacity during the next 15 years are described in brief. The major achievements during last ten years are: (1) development and irradiation testing of mixed uranium plutonium oxide (MOX), as an alternative fuel for boiling water reactors at Tarapur, (2) setting up of a 10 tons/year pilot plant for fabrication of oxide fuels and technical support for setting up such plants, (3) development and production of plutonium rich, advanced mixed uranium plutonium monocarbide driver fuel for the Fast Breeder Test Reactor comm issioned at Kalpakkam, (4) development and fabrication of Al- 233 U plate fuel elements for KAMINI reactor, (5) PIE of fuel elements from Indian reactors in operation, (6) failure analysis of reactor components, and (7) in-pile performance analysis of power reactor structural materials. A list of publications during 1978-88 by the scientists of the Division is given at the end. The publications are listed under the headings: (1) fuels, (2) non-destructive evaluation, (3) engineering development, (4) welding development, (5) characterization and property evaluation, and (6) post irradiation examination. The entire text is illustrated with a number of diagrams and photographs - many of them coloured . (M.G.B.)

Field test of wireless sensor network in the nuclear environment

International Nuclear Information System (INIS)

Li, L.; Wang, Q.; Bari, A.; Deng, C.; Chen, D.; Jiang, J.; Alexander, Q.; Sur, B.

2014-01-01

Wireless sensor networks (WSNs) are appealing options for the health monitoring of nuclear power plants due to their low cost and flexibility. Before they can be used in highly regulated nuclear environments, their reliability in the nuclear environment and compatibility with existing devices have to be assessed. In situ electromagnetic interference tests, wireless signal propagation tests, and nuclear radiation hardness tests conducted on candidate WSN systems at AECL Chalk River Labs are presented. The results are favourable to WSN in nuclear applications. (author)

Field test of wireless sensor network in the nuclear environment

Energy Technology Data Exchange (ETDEWEB)

Li, L., E-mail: lil@aecl.ca [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Wang, Q.; Bari, A. [Univ. of Western Ontario, London, Ontario (Canada); Deng, C.; Chen, D. [Univ. of Electronic Science and Technology of China, Chengdu, Sichuan (China); Jiang, J. [Univ. of Western Ontario, London, Ontario (Canada); Alexander, Q.; Sur, B. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)

2014-06-15

Wireless sensor networks (WSNs) are appealing options for the health monitoring of nuclear power plants due to their low cost and flexibility. Before they can be used in highly regulated nuclear environments, their reliability in the nuclear environment and compatibility with existing devices have to be assessed. In situ electromagnetic interference tests, wireless signal propagation tests, and nuclear radiation hardness tests conducted on candidate WSN systems at AECL Chalk River Labs are presented. The results are favourable to WSN in nuclear applications. (author)

Energy Technology Division research summary 1997

International Nuclear Information System (INIS)

1997-01-01

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy. As shown on the preceding page, the Division is organized into ten sections, five with concentrations in the materials area and five in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officers, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. The Division's capabilities are generally applied to issues associated with energy production, transportation, utilization or conservation, or with environmental issues linked to energy. As shown in the organization chart on the next page, the Division reports administratively to the Associate Laboratory Director (ALD) for Energy and Environmental Science and Technology (EEST) through the General Manager for Environmental and Industrial Technologies. While most of our programs are under the purview of the EEST ALD, we also have had programs funded under every one of the ALDs. Some of our research in superconductivity is funded through the Physical Research Program ALD. We also continue to work on a number of nuclear-energy-related programs under the ALD for Engineering Research. Detailed descriptions of our programs on a section-by-section basis are provided in the remainder of this book. This Overview highlights some major trends. Research related to the operational safety of commercial light water nuclear

Energy Technology Division research summary 1997.

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-21

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy. As shown on the preceding page, the Division is organized into ten sections, five with concentrations in the materials area and five in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officers, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. The Division's capabilities are generally applied to issues associated with energy production, transportation, utilization or conservation, or with environmental issues linked to energy. As shown in the organization chart on the next page, the Division reports administratively to the Associate Laboratory Director (ALD) for Energy and Environmental Science and Technology (EEST) through the General Manager for Environmental and Industrial Technologies. While most of our programs are under the purview of the EEST ALD, we also have had programs funded under every one of the ALDs. Some of our research in superconductivity is funded through the Physical Research Program ALD. We also continue to work on a number of nuclear-energy-related programs under the ALD for Engineering Research. Detailed descriptions of our programs on a section-by-section basis are provided in the remainder of this book. This Overview highlights some major trends. Research related to the operational safety of commercial light water

Ergonomic Analysis of Garment Industry using Posture Evaluation Index (PEI) in Virtual Environment

OpenAIRE

Erlinda Muslim; Boy Nurtjahyo; Romadhani Ardi

2011-01-01

This research tried to study, in a virtual environment, the ergonomics of four divisions in garment industry: cutting division, sewing division, button division, and finishing division. Variables that influence the working conditions in each division are different; depend on the real situations that happened. The purpose is to assess the real working conditions based on ergonomics  study  using Posture Evaluation Index (PEI). PEI integrates  the scores of  low back analysi...

Technical activities, 1990: Surface Science Division

International Nuclear Information System (INIS)

Powell, C.J.

1991-05-01

The report summarizes technical activities and accomplishments of the NIST Surface Science Division during Fiscal Year 1990. Overviews are presented of the Division and of its three constituent groups: Surface Dynamical Processes, Thin Films and Interfaces, and Surface Spectroscopies and Standards. These overviews are followed by reports of selected technical accomplishments during the year. A summary is given of Division outputs and interactions that includes lists of publications, talks, committee assignments, seminars (including both Division seminars and Interface Science seminars arranged through the Division), conferences organized, and a standard reference material certified. Finally, lists are given of Division staff and of guest scientists who have worked in the Division during the past year

Overview of the Space Launch System Ascent Aeroacoustic Environment Test Program

Science.gov (United States)

Herron, Andrew J.; Crosby, William A.; Reed, Darren K.

2016-01-01

Characterization of accurate flight vehicle unsteady aerodynamics is critical for component and secondary structure vibroacoustic design. The Aerosciences Branch at the National Aeronautics and Space Administration (NASA) Marshall Space Flight Center has conducted a test at the NASA Ames Research Center (ARC) Unitary Plan Wind Tunnels (UPWT) to determine such ascent aeroacoustic environments for the Space Launch System (SLS). Surface static pressure measurements were also collected to aid in determination of local environments for venting, CFD substantiation, and calibration of the flush air data system located on the launch abort system. Additionally, this test supported a NASA Engineering and Safety Center study of alternate booster nose caps. Testing occurred during two test campaigns: August - September 2013 and December 2013 - January 2014. Four primary model configurations were tested for ascent aeroacoustic environment definition. The SLS Block 1 vehicle was represented by a 2.5% full stack model and a 4% truncated model. Preliminary Block 1B payload and manned configurations were also tested, using 2.5% full stack and 4% truncated models respectively. This test utilized the 11 x 11 foot transonic and 9 x 7 foot supersonic tunnel sections at the ARC UPWT to collect data from Mach 0.7 through 2.5 at various total angles of attack. SLS Block 1 design environments were developed primarily using these data. SLS Block 1B preliminary environments have also been prepared using these data. This paper discusses the test and analysis methodology utilized, with a focus on the unsteady data collection and processing.

AEC testing in a CR environment

International Nuclear Information System (INIS)

McLeod, R.

2004-01-01

Full text: Testing of x-ray machine automatic exposure control (AEC) functionality for varying kVp and patient thickness is a fundamental health physics check. Current test protocols tend to be based on testing in a film environment using film optical density as the measure of conformance. With the move into the digital x-ray image age with the use of computed radiography (CR) and digital radiography (DR) equipment and its associated image storage and retrieval system (PACS) a new AEC testing protocol is required. All CR systems provide a dose assessment tool (called Exposure Index or EI by Kodak) that could be used as a surrogate for optical density. However this work aims to derive an efficient means of assessing the functioning of the AEC of x-ray machines in a CR environment using dose measurement alone. This would eliminate the need to process the many image plates normally required for AEC testing in order to obtain and analyse the exposure measure from the CR system. The EI, and other brand's equivalents, is calibrated for a given condition (for Kodak 80kVp 0.5mmCu + 1mmAl). In order to use dose measurement alone the relationship between EI and dose must be known for varying kVp and patient thicknesses (represented by a perspex phantom). This will depend on the response of the CR plate to varying beam energies. This was assessed using a series of paired exposures at various kVp and perspex thicknesses. In the first exposure of each pair a Kodak CR plate was used, processed in the normal way, and the EI noted. In a second identical exposure an Innovision 35050A pancake ionization chamber was placed in the bucky tray within a specially modified film cassette and the dose measured. Over the 50-125kVp range of clinical use the kV response of the Kodak PSP's shown below is essentially flat for a set dose to the image plate and filtered using the standard Kodak method of 0.5mmCu + 1mmAl. Similar data will be presented showing this relationship using a perspex

How bacterial cell division might cheat turgor pressure - a unified mechanism of septal division in Gram-positive and Gram-negative bacteria.

Science.gov (United States)

Erickson, Harold P

2017-08-01

An important question for bacterial cell division is how the invaginating septum can overcome the turgor force generated by the high osmolarity of the cytoplasm. I suggest that it may not need to. Several studies in Gram-negative bacteria have shown that the periplasm is isoosmolar with the cytoplasm. Indirect evidence suggests that this is also true for Gram-positive bacteria. In this case the invagination of the septum takes place within the uniformly high osmotic pressure environment, and does not have to fight turgor pressure. A related question is how the V-shaped constriction of Gram-negative bacteria relates to the plate-like septum of Gram-positive bacteria. I collected evidence that Gram-negative bacteria have a latent capability of forming plate-like septa, and present a model in which septal division is the basic mechanism in both Gram-positive and Gram-negative bacteria. © 2017 WILEY Periodicals, Inc.

Avoidance behaviour testing of Eisenia andrei in biodegradable plastic environment

Directory of Open Access Journals (Sweden)

Zuzana Tichá

2013-01-01

Full Text Available Avoidance behaviour test with the earthworms (ISO 17512-1:2008 is a rapid screening test for the evaluation of soil and the influence of pollutants and chemicals on the behaviour of earthworms. The purpose of the testing is to determine the avoidance behaviour of earthworm (in this case Eisenia andrei was used which can be used as an organism for the composting and occur naturally in soil environment. The methodology was modified according to the needs of the avoidance behaviour testing of earthworms in biodegradable plastic environment. It is a biodegradable thermoplastic material Mater-Bi, which is produced from corn starch. Californian earthworm (Eisenia andrei was chosen as a test organism. The two-chamber test was used in testing. 10 earthworms were used, which were exposed to a number of concentrations of the test substance, which was mixed into the compost environment. It was recorded both a positive result, avoidance reaction, as well as a negative result, non-avoidance reaction and also there was a case, where individuals prefer both substrates equally. Organisms showed no escape reaction and were fairly evenly distributed in both halves of the test vessel, it can be assessed that organisms prefer both substrates equally. In testing, the mortality was zero, none of the individuals died, at the conclusion of the test there were not found any dead individuals. Avoidance higher than 80 % didn’t occur; it cannot be said that the substrate is toxic or degraded.

Deconstructing Interocular Suppression: Attention and Divisive Normalization.

Directory of Open Access Journals (Sweden)

Hsin-Hung Li

2015-10-01

Full Text Available In interocular suppression, a suprathreshold monocular target can be rendered invisible by a salient competitor stimulus presented in the other eye. Despite decades of research on interocular suppression and related phenomena (e.g., binocular rivalry, flash suppression, continuous flash suppression, the neural processing underlying interocular suppression is still unknown. We developed and tested a computational model of interocular suppression. The model included two processes that contributed to the strength of interocular suppression: divisive normalization and attentional modulation. According to the model, the salient competitor induced a stimulus-driven attentional modulation selective for the location and orientation of the competitor, thereby increasing the gain of neural responses to the competitor and reducing the gain of neural responses to the target. Additional suppression was induced by divisive normalization in the model, similar to other forms of visual masking. To test the model, we conducted psychophysics experiments in which both the size and the eye-of-origin of the competitor were manipulated. For small and medium competitors, behavioral performance was consonant with a change in the response gain of neurons that responded to the target. But large competitors induced a contrast-gain change, even when the competitor was split between the two eyes. The model correctly predicted these results and outperformed an alternative model in which the attentional modulation was eye specific. We conclude that both stimulus-driven attention (selective for location and feature and divisive normalization contribute to interocular suppression.

Deconstructing Interocular Suppression: Attention and Divisive Normalization.

Science.gov (United States)

Li, Hsin-Hung; Carrasco, Marisa; Heeger, David J

2015-10-01

In interocular suppression, a suprathreshold monocular target can be rendered invisible by a salient competitor stimulus presented in the other eye. Despite decades of research on interocular suppression and related phenomena (e.g., binocular rivalry, flash suppression, continuous flash suppression), the neural processing underlying interocular suppression is still unknown. We developed and tested a computational model of interocular suppression. The model included two processes that contributed to the strength of interocular suppression: divisive normalization and attentional modulation. According to the model, the salient competitor induced a stimulus-driven attentional modulation selective for the location and orientation of the competitor, thereby increasing the gain of neural responses to the competitor and reducing the gain of neural responses to the target. Additional suppression was induced by divisive normalization in the model, similar to other forms of visual masking. To test the model, we conducted psychophysics experiments in which both the size and the eye-of-origin of the competitor were manipulated. For small and medium competitors, behavioral performance was consonant with a change in the response gain of neurons that responded to the target. But large competitors induced a contrast-gain change, even when the competitor was split between the two eyes. The model correctly predicted these results and outperformed an alternative model in which the attentional modulation was eye specific. We conclude that both stimulus-driven attention (selective for location and feature) and divisive normalization contribute to interocular suppression.

2010-11 Research Portfolio: Research & Development Division

Science.gov (United States)

Educational Testing Service, 2010

2010-01-01

This document describes the breadth of the research that the ETS (Educational Testing Service) Research & Development division is conducting in 2010. This portfolio will be updated in early 2011 to reflect changes to existing projects and new projects that were added after this document was completed. The research described in this portfolio falls…

E-Division activities report

International Nuclear Information System (INIS)

Barschall, H.H.

1984-07-01

E (Experimental Physics) Division carries out basic and applied research in atomic and nuclear physics, in materials science, and in other areas related to the missions of the Laboratory. Some of the activities are cooperative efforts with other divisions of the Laboratory, and, in a few cases, with other laboratories. Many of the experiments are directly applicable to problems in weapons and energy, some have only potential applied uses, and others are in pure physics. This report presents abstracts of papers published by E (Experimental Physics) Division staff members between July 1983 and June 1984. In addition, it lists the members of the scientific staff of the division, including visitors and students, and some of the assignments of staff members on scientific committees. A brief summary of the budget is included

Reliability Verification of DBE Environment Simulation Test Facility by using Statistics Method

International Nuclear Information System (INIS)

Jang, Kyung Nam; Kim, Jong Soeg; Jeong, Sun Chul; Kyung Heum

2011-01-01

In the nuclear power plant, all the safety-related equipment including cables under the harsh environment should perform the equipment qualification (EQ) according to the IEEE std 323. There are three types of qualification methods including type testing, operating experience and analysis. In order to environmentally qualify the safety-related equipment using type testing method, not analysis or operation experience method, the representative sample of equipment, including interfaces, should be subjected to a series of tests. Among these tests, Design Basis Events (DBE) environment simulating test is the most important test. DBE simulation test is performed in DBE simulation test chamber according to the postulated DBE conditions including specified high-energy line break (HELB), loss of coolant accident (LOCA), main steam line break (MSLB) and etc, after thermal and radiation aging. Because most DBE conditions have 100% humidity condition, in order to trace temperature and pressure of DBE condition, high temperature steam should be used. During DBE simulation test, if high temperature steam under high pressure inject to the DBE test chamber, the temperature and pressure in test chamber rapidly increase over the target temperature. Therefore, the temperature and pressure in test chamber continue fluctuating during the DBE simulation test to meet target temperature and pressure. We should ensure fairness and accuracy of test result by confirming the performance of DBE environment simulation test facility. In this paper, in order to verify reliability of DBE environment simulation test facility, statistics method is used

Chemical Technology Division annual technical report 1989

International Nuclear Information System (INIS)

1990-03-01

Highlights of the Chemical Technology (CMT) Division's activities during 1989 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including high-performance batteries (mainly lithium/iron sulfide and sodium/metal chloride), aqueous batteries (lead-acid and nickel/iron), and advanced fuel cells with molten carbonate and solid oxide electrolytes: (2) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (3) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste and for producing 99 Mo from low-enriched uranium targets, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor (the Integral Fast Reactor), and waste management; and (5) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be administratively responsible for and the major user of the Analytical Chemistry Laboratory at Argonne National Laboratory (ANL)

Chemical Technology Division annual technical report, 1988

International Nuclear Information System (INIS)

1989-05-01

Highlights of the Chemical Technology (CMT) Divisions's activities during 1988 are presented. In this period, CMT conducted research and development in the following areas: (1) high-performance batteries (mainly lithium-alloy/metal sulfide, sodium/metal chloride, and sodium/sulfur); (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (5) methods for recovery of energy from municipal waste and techniques for treatment of hazardous chemical water; (6) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste and for producing /sup 99/Mo from low-enriched uranium targets, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor, and waste management; and (7) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 53 figs., 16 tabs

Progress report of Applied Physics Division. 1 October 1980 - 30 June 1981. Acting Division Chief - Dr. J. Parry

International Nuclear Information System (INIS)

2004-01-01

In September 1980, the Commission approved a reorganization of Physics Division, Engineering Research Division and Instrumentation and Control Division to form two new research divisions to be known as Applied Physics Division and Nuclear Technology Division. The Applied Physics Division will be responsible for applied science programs, particularly those concerned with nuclear techniques. The Division is organized as four sections with the following responsibilities: (1) Nuclear Applications and Energy Studies Section. Program includes studies in nuclear physics, nuclear applications, ion implantation and neutron scattering. (2) Semiconductor and Radiation Physics Section. Studies in semiconductor radiation detectors, radiation standards and laser applications. (3) Electronic Systems Section. This includes systems analysis, digital systems, instrument design, project instrumentation and instrument maintenance. (4) Fusion Physics Section. This covers work carried out by staff currently attached to university groups (author)

Chemical Technology Division annual technical report, 1993

Energy Technology Data Exchange (ETDEWEB)

Battles, J.E.; Myles, K.M.; Laidler, J.J.; Green, D.W.

1994-04-01

Chemical Technology (CMT) Division this period, conducted research and development in the following areas: advanced batteries and fuel cells; fluidized-bed combustion and coal-fired magnetohydrodynamics; treatment of hazardous waste and mixed hazardous/radioactive waste; reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; separating and recovering transuranic elements, concentrating radioactive waste streams with advanced evaporators, and producing {sup 99}Mo from low-enriched uranium; recovering actinide from IFR core and blanket fuel in removing fission products from recycled fuel, and disposing removal of actinides in spent fuel from commercial water-cooled nuclear reactors; and physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, molecular sieve structures, thin-film diamond surfaces, effluents from wood combustion, and molten silicates; and the geochemical processes involved in water-rock interactions. The Analytical Chemistry Laboratory in CMT also provides a broad range of analytical chemistry support.

Chemical Technology Division annual technical report, 1993

International Nuclear Information System (INIS)

Battles, J.E.; Myles, K.M.; Laidler, J.J.; Green, D.W.

1994-04-01

Chemical Technology (CMT) Division this period, conducted research and development in the following areas: advanced batteries and fuel cells; fluidized-bed combustion and coal-fired magnetohydrodynamics; treatment of hazardous waste and mixed hazardous/radioactive waste; reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; separating and recovering transuranic elements, concentrating radioactive waste streams with advanced evaporators, and producing 99 Mo from low-enriched uranium; recovering actinide from IFR core and blanket fuel in removing fission products from recycled fuel, and disposing removal of actinides in spent fuel from commercial water-cooled nuclear reactors; and physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, molecular sieve structures, thin-film diamond surfaces, effluents from wood combustion, and molten silicates; and the geochemical processes involved in water-rock interactions. The Analytical Chemistry Laboratory in CMT also provides a broad range of analytical chemistry support

Division Quilts: A Measurement Model

Science.gov (United States)

Pratt, Sarah S.; Lupton, Tina M.; Richardson, Kerri

2015-01-01

As teachers seek activities to assist students in understanding division as more than just the algorithm, they find many examples of division as fair sharing. However, teachers have few activities to engage students in a quotative (measurement) model of division. Efraim Fischbein and his colleagues (1985) defined two types of whole-number…

Grouping of Environments for Testing Navy Bean in Ethiopia ...

African Journals Online (AJOL)

Kassaye

bean (Phaseolus vulgaris L.) lines was tested in a multi-environment variety trial ... of methods available for the analysis of GEI and stability. .... parameters in the kth bilinear term are obtained as the kth component of the .... AMMI ANOVA of grain yield for 16 navy bean lines at fourteen environments during 2010 – 2011 main ...

Atmospheric sciences division. Annual report, fiscal year 1981

International Nuclear Information System (INIS)

Raynor, G.S.

1981-12-01

The research activities of the Atmospheric Sciences Division of the Department of Energy and Environment for FY 1981 are presented. Facilities and major items of equipment are described. Research programs are summarized in three categories, modeling, field and laboratory experiments and data management and analysis. Each program is also described individually with title, principal investigator, sponsor and funding levels for FY 1981 and FY 1982. Future plans are summarized. Publications for FY 1981 are listed with abstracts. A list of personnel is included

Comparison of Concussion Rates Between NCAA Division I and Division III Men's and Women's Ice Hockey Players.

Science.gov (United States)

Rosene, John M; Raksnis, Bryan; Silva, Brie; Woefel, Tyler; Visich, Paul S; Dompier, Thomas P; Kerr, Zachary Y

2017-09-01

Examinations related to divisional differences in the incidence of sports-related concussions (SRC) in collegiate ice hockey are limited. To compare the epidemiologic patterns of concussion in National Collegiate Athletic Association (NCAA) ice hockey by sex and division. Descriptive epidemiology study. A convenience sample of men's and women's ice hockey teams in Divisions I and III provided SRC data via the NCAA Injury Surveillance Program during the 2009-2010 to 2014-2015 academic years. Concussion counts, rates, and distributions were examined by factors including injury activity and position. Injury rate ratios (IRRs) and injury proportion ratios (IPRs) with 95% confidence intervals (CIs) were used to compare concussion rates and distributions, respectively. Overall, 415 concussions were reported for men's and women's ice hockey combined. The highest concussion rate was found in Division I men (0.83 per 1000 athlete-exposures [AEs]), followed by Division III women (0.78/1000 AEs), Division I women (0.65/1000 AEs), and Division III men (0.64/1000 AEs). However, the only significant IRR was that the concussion rate was higher in Division I men than Division III men (IRR = 1.29; 95% CI, 1.02-1.65). The proportion of concussions from checking was higher in men than women (28.5% vs 9.4%; IPR = 3.02; 95% CI, 1.63-5.59); however, this proportion was higher in Division I women than Division III women (18.4% vs 1.8%; IPR = 10.47; 95% CI, 1.37-79.75). The proportion of concussions sustained by goalkeepers was higher in women than men (14.2% vs 2.9%; IPR = 4.86; 95% CI, 2.19-10.77), with findings consistent within each division. Concussion rates did not vary by sex but differed by division among men. Checking-related concussions were less common in women than men overall but more common in Division I women than Division III women. Findings highlight the need to better understand the reasons underlying divisional differences within men's and women's ice hockey and the

Differences in strength and conditioning coach self-perception of leadership style behaviors at the National Basketball Association, Division I-A, and Division II levels.

Science.gov (United States)

Magnusen, Marshall J

2010-06-01

Leader behaviors have been found to vary by competitive level (6,9,11,26). Similar differences based on the competitive environment have been reported with strength coaches and their training emphases (15,28) but not their leadership style behaviors. This latter area is important to explore because strength coach leader behaviors may result in enhanced cooperation, improved communication, and improved athlete psychological and emotional well-being (14,23,25,27). Accordingly, the purpose of this study was to examine the differences in self-perceived leadership styles of National Basketball Association, Division I-A (DI-A) men's basketball, and Division II (DII) men's basketball strength and conditioning coaches. The self-perceived leadership styles of 145 men's basketball strength coaches (National Basketball Association [NBA]=22, DI-A=92, and DII=31) were obtained using the Revised Leadership Scale for Sport (26,41). Frequency data about demographics and training methods were also collected. No significant differences were reported for positive feedback. Otherwise, NBA strength coaches reported more democratic leadership style behaviors than DI-A strength coaches. Division I-A strength coaches were found to be more autocratic than NBA or DII strength coaches. Both NBA and DI-A strength coaches indicated a higher level of training and instruction than did DII strength coaches. National Basketball Association strength coaches also reported engaging in more situational and socially supportive leader behaviors than DI-A and DII strength coaches. Leader behaviors can positively and negatively impact an athlete (23); thus, strength coaches need to evaluate their competitive environment and reflect on the impact of their behaviors and how their approach to leading athletes may need to vary based on the situation.

Ergonomic Analysis of Garment Industry using Posture Evaluation Index (PEI in Virtual Environment

Directory of Open Access Journals (Sweden)

Erlinda Muslim

2011-09-01

Full Text Available This research tried to study, in a virtual environment, the ergonomics of four divisions in garment industry: cutting division, sewing division, button division, and finishing division. Variables that influence the working conditions in each division are different; depend on the real situations that happened. The purpose is to assess the real working conditions based on ergonomics  study  using Posture Evaluation Index (PEI. PEI integrates  the scores of  low back analysis (LBA, ovako working  posture  (OWAS,  and  rapid  upper  limb assessment  (RULA.  Analysis  phase  was  done  using  digital  human model  in  virtual  environment  that  available  on  Jack  6.0.  The  results show  that  the  working  conditions  in  garment industry had enough amount of risk that can injured the musculoskeletal system of the workers. This research enriches the  body  of  ergonomics  knowledge  in Indonesia  because  it  is  the  first  research  in  Indonesia that  applied  virtual environment approach to ergonomics analysis in industry.

Ontario Hydro Research Division, 1980

International Nuclear Information System (INIS)

The work of the Research Division of Ontario Hydro provides technical and scientific support for the engineering and operation of a power system that includes hydraulic, fossil-fired, and nuclear generation. It also relates to the transmission and distribution of electricity and to the need to help customers use electricity with safety and economy. Among the examples of projects given are qualification of CANDU heat transport system components, pressure tube replacement, steam generator integrity, testing for earthquake resistance, and radioactive waste disposal

Environment, Safety, and Health Self-Assessment Report, Fiscal Year 2008

Energy Technology Data Exchange (ETDEWEB)

Chernowski, John

2009-02-27

Lawrence Berkeley National Laboratory's Environment, Safety, and Health (ES&H) Self-Assessment Program ensures that Integrated Safety Management (ISM) is implemented institutionally and by all divisions. The Self-Assessment Program, managed by the Office of Contract Assurance (OCA), provides for an internal evaluation of all ES&H programs and systems at LBNL. The functions of the program are to ensure that work is conducted safely, and with minimal negative impact to workers, the public, and the environment. The Self-Assessment Program is also the mechanism used to institute continuous improvements to the Laboratory's ES&H programs. The program is described in LBNL/PUB 5344, Environment, Safety, and Health Self-Assessment Program and is composed of four distinct assessments: the Division Self-Assessment, the Management of Environment, Safety, and Health (MESH) review, ES&H Technical Assurance, and the Appendix B Self-Assessment. The Division Self-Assessment uses the five core functions and seven guiding principles of ISM as the basis of evaluation. Metrics are created to measure performance in fulfilling ISM core functions and guiding principles, as well as promoting compliance with applicable regulations. The five core functions of ISM are as follows: (1) Define the Scope of Work; (2) Identify and Analyze Hazards; (3) Control the Hazards; (4) Perform the Work; and (5) Feedback and Improvement. The seven guiding principles of ISM are as follows: (1) Line Management Responsibility for ES&H; (2) Clear Roles and Responsibilities; (3) Competence Commensurate with Responsibilities; (4) Balanced Priorities; (5) Identification of ES&H Standards and Requirements; (6) Hazard Controls Tailored to the Work Performed; and (7) Operations Authorization. Performance indicators are developed by consensus with OCA, representatives from each division, and Environment, Health, and Safety (EH&S) Division program managers. Line management of each division performs the

Rocketdyne division annual site environmental report, Santa Susana Field Laboratory and De Soto Sites, 1992

Energy Technology Data Exchange (ETDEWEB)

none,

1993-12-14

This annual report discusses environmental monitoring at two manufacturing and test operations sites operated in the Los Angeles area by the Rocketdyne Division of Rockwell International Corporation. These are identified as the Santa Susana Field Laboratory (SSFL) and the De Soto site. These sites have been used for manufacturing, R&D, engineering, and testing in a broad range of technical fields, primarily rocket engine propulsion and nuclear reactor technology. The De Soto site is essentially light industry with some laboratory-scale R&D and has little potential impact on the environment. The SSFL site, because of its large size (2,668 acres), warranted comprehensive monitoring to assure protection of the environment. The purpose of this report is to present information on environmental and effluent monitoring primarily for the regulatory agencies involved in controlling environmental remediation, i.e., the U.S. DOE, the Nuclear Regulatory Commission (NRC), and the California State Department of Health Services (DHS) Radiologic Health Branch (RHB). For that reason, information concentrates on Area IV at SSFL as this is the site of the former nuclear operations. While the major area of interest is radiological, this report also includes a discussion of nonradiological monitoring at SSFL.

Rocketdyne division annual site environmental report, Santa Susana Field Laboratory and De Soto Site, 1991

Energy Technology Data Exchange (ETDEWEB)

none,

1992-12-03

This annual report discusses environmental monitoring at two manufacturing and test operations sites operated in the Los Angeles area by the Rocketdyne Division of Rockwell International Corporation. These are identified as the Santa Susana Field Laboratory (SSFL) and the De Soto site. These sites have been used for manufacturing, R&D, engineering, and testing in a broad range of technical fields, primarily rocket engine propulsion and nuclear reactor technology. The De Soto site is essentially light industry with some laboratory-scale R&D and has little potential impact on the environment. The SSFL site, because of its large size (2.668 acres), warranted comprehensive monitoring to assure protection of the environment. The purpose of this report is to present information on environmental and effluent monitoring primarily for the regulatory agencies involved in controlling operations with nuclear fuel or nuclear reactors. i.e., the U.S. DOE and the California State Department of Health Services (DHS). Radiologic Health Branch (RHB). For that reason. information concentrates on Area IV at SSFL as this is the site of the former nuclear operations. While the major area of interest is radiological, this report also includes a discussion of nonradiological monitoring at SSFL.

Rocketdyne division annual site environmental report, Santa Susana Field Laboratory and De Soto Sites, 1993

Energy Technology Data Exchange (ETDEWEB)

None, None

1994-10-21

This annual report discusses environmental monitoring at two manufacturing and test operations sites operated in the Los Angeles area by the Rocketdyne Division of Rockwell International Corporation. These are identified as the Santa Susana Field Laboratory (SSFL) and the De Soto site. These sites have been used for manufacturing, R&D, engineering, and testing in a broad range of technical fields, primarily rocket engine propulsion and nuclear reactor technology. The De Soto site is essentially light industry with some laboratory-scale R&D and has little potential impact on the environment. The SSFL site, because of its large size (2,668 acres), warranted comprehensive monitoring to assure protection of the environment. The purpose of this report is to present information on environmental and effluent monitoring primarily for the regulatory agencies involved in controlling environmental remediation, i.e., the U.S. DOE, the Nuclear Regulatory Commission (NRC), and the California State Department of Health Services (DHS) Radiologic Health Branch (RHB). For that reason, information concentrates on Area IV at SSFL as this is the site of the former nuclear operations. While the major area of interest is radiological, this report also includes a discussion of nonoradiological monitoring at SSFL.

Energy and Environment Division, annual report FY 1980

Energy Technology Data Exchange (ETDEWEB)

Osowitt, M. (ed.)

1981-07-01

This report covers research in: energy analysis; energy efficiency studies; solar energy; chemical process; energy-efficient buildings; environmental pollutant studies; combustion research; laser spectroscopy and trace elements; and oil shale and coal research. An energy and environment personnel listing is appended. Separate projects are indexed individually for the database. (PSB)

Progress report of Environmental Assessment Division 1991-1994

International Nuclear Information System (INIS)

Sadasivan, S.; Nambi, K.S.V.

1994-01-01

The research and development (R and D) activities of Environmental Assessment Division during the period 1991-1994 are reported in the form of individual summaries arranged under the headings: 1) Studies on radioactivity measurements, 2) Dosimetry, 3) Epidemiological studies, 4) Aerosol studies, 5) Pollution monitoring systems, 6) Studies on trace constituents in the environment, and 7) Modelling studies. At the end of the report a list of publications including papers published in journals, presented at symposia, conferences etc., and published technical reports is given. (author)

Progress report of Environmental Assessment Division 1991-1994

Energy Technology Data Exchange (ETDEWEB)

Sadasivan, S; Nambi, K S.V. [comps.; Bhabha Atomic Research Centre, Bombay (India). Environmental Assessment Div.

1994-12-31

The research and development (R and D) activities of Environmental Assessment Division during the period 1991-1994 are reported in the form of individual summaries arranged under the headings: (1) Studies on radioactivity measurements, (2) Dosimetry, (3) Epidemiological studies, (4) Aerosol studies, (5) Pollution monitoring systems, (6) Studies on trace constituents in the environment, and (7) Modelling studies. At the end of the report a list of publications including papers published in journals, presented at symposia, conferences etc., and published technical reports is given. (author).

77 FR 40586 - Coastal Programs Division

Science.gov (United States)

2012-07-10

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration Coastal Programs Division AGENCY: Coastal Programs Division, Office of Ocean and Coastal Resource Management, National Ocean.... FOR FURTHER INFORMATION CONTACT: Kerry Kehoe, Coastal Programs Division (NORM/3), Office of Ocean and...

Life Sciences Division progress report for CYs 1997-1998[Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Mann, Reinhold C.

1999-01-01

common mission of the division is to advance science and technology to understand complex biological systems and their relationship with human health and the environment

Life Sciences Division progress report for CYs 1997-1998 [Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Mann, Reinhold C.

1999-06-01

common mission of the division is to advance science and technology to understand complex biological systems and their relationship with human health and the environment.

Dense wavelength division multiplexing devices for metropolitan-area datacom and telecom networks

Science.gov (United States)

DeCusatis, Casimer M.; Priest, David G.

2000-12-01

Large data processing environments in use today can require multi-gigabyte or terabyte capacity in the data communication infrastructure; these requirements are being driven by storage area networks with access to petabyte data bases, new architecture for parallel processing which require high bandwidth optical links, and rapidly growing network applications such as electronic commerce over the Internet or virtual private networks. These datacom applications require high availability, fault tolerance, security, and the capacity to recover from any single point of failure without relying on traditional SONET-based networking. These requirements, coupled with fiber exhaust in metropolitan areas, are driving the introduction of dense optical wavelength division multiplexing (DWDM) in data communication systems, particularly for large enterprise servers or mainframes. In this paper, we examine the technical requirements for emerging nextgeneration DWDM systems. Protocols for storage area networks and computer architectures such as Parallel Sysplex are presented, including their fiber bandwidth requirements. We then describe two commercially available DWDM solutions, a first generation 10 channel system and a recently announced next generation 32 channel system. Technical requirements, network management and security, fault tolerant network designs, new network topologies enabled by DWDM, and the role of time division multiplexing in the network are all discussed. Finally, we present a description of testing conducted on these networks and future directions for this technology.

Chemical technology division: Annual technical report 1987

International Nuclear Information System (INIS)

1988-05-01

Highlights of the Chemical Technology (CMT) Division's activities during 1987 are presented. In this period, CMT conducted research and development in the following areas: (1) high-performance batteries--mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (5) methods for the electromagnetic continuous casting of steel sheet and for the purification of ferrous scrap; (6) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (7) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor, and waste management; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for liquids and vapors at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; the thermochemistry of various minerals; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 54 figs., 9 tabs

Chemical Technology Division annual technical report 1989

Energy Technology Data Exchange (ETDEWEB)

1990-03-01

Highlights of the Chemical Technology (CMT) Division's activities during 1989 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including high-performance batteries (mainly lithium/iron sulfide and sodium/metal chloride), aqueous batteries (lead-acid and nickel/iron), and advanced fuel cells with molten carbonate and solid oxide electrolytes: (2) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (3) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste and for producing {sup 99}Mo from low-enriched uranium targets, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor (the Integral Fast Reactor), and waste management; and (5) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be administratively responsible for and the major user of the Analytical Chemistry Laboratory at Argonne National Laboratory (ANL).

Chemical technology division: Annual technical report 1987

Energy Technology Data Exchange (ETDEWEB)

1988-05-01

Highlights of the Chemical Technology (CMT) Division's activities during 1987 are presented. In this period, CMT conducted research and development in the following areas: (1) high-performance batteries--mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (5) methods for the electromagnetic continuous casting of steel sheet and for the purification of ferrous scrap; (6) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (7) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor, and waste management; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for liquids and vapors at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; the thermochemistry of various minerals; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 54 figs., 9 tabs.

Chemical Technology Division annual technical report, 1986

International Nuclear Information System (INIS)

1987-06-01

Highlights of the Chemical Technology (CMT) Division's activities during 1986 are presented. In this period, CMT conducted research and development in areas that include the following: (1) high-performance batteries - mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants, the technology for fluidized-bed combustion, and a novel concept for CO 2 recovery from fossil fuel combustion; (5) methods for recovery of energy from municipal waste; (6) methods for the electromagnetic continuous casting of steel sheet; (7) techniques for treatment of hazardous waste such as reactive metals and trichloroethylenes; (8) nuclear technology related to waste management, a process for separating and recovering transuranic elements from nuclear waste, and the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor; and (9) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of catalytic hydrogenation and catalytic oxidation; materials chemistry for associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, surface science, and catalysis; the thermochemistry of zeolites and related silicates; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 127 refs., 71 figs., 8 tabs

Indoor Environment Program

International Nuclear Information System (INIS)

Daisey, J.M.

1993-06-01

This paper reports progress during the year 1992 in the Indoor Environment Program in the Energy and Environment Division of Lawrence Berkeley Laboratory. Studies in the following areas are reported: energy performance and ventilation in buildings; physical and chemical characterization of indoor air pollutants; indoor radon; indoor air quality; exposure to indoor air pollutants and risk analysis. Pollutants of particular interest include: radon; volatile, semi-volatile and particulate organic compounds; and combustion emissions including environmental tobacco smoke, carbon monoxide, and nitrogen oxides

Theoretical Division progress report

International Nuclear Information System (INIS)

Cooper, N.G.

1979-04-01

This report presents highlights of activities in the Theoretical (T) Division from October 1976-January 1979. The report is divided into three parts. Part I presents an overview of the Division: its unique function at the Los Alamos Scientific Laboratory (LASL) and within the scientific community as a whole; the organization of personnel; the main areas of research; and a survey of recent T-Division initiatives. This overview is followed by a survey of the 13 groups within the Division, their main responsibilities, interests, and expertise, consulting activities, and recent scientific accomplisments. The remainder of the report, Parts II and III, is devoted to articles on selected research activities. Recent efforts on topics of immediate interest to energy and weapons programs at LASL and elsewhere are described in Part II, Major National Programs. Separate articles present T-Divison contributions to weapons research, reactor safety and reactor physics research, fusion research, laser isotope separation, and other energy research. Each article is a compilation of independent projects within T Division, all related to but addressing different aspects of the major program. Part III is organized by subject discipline, and describes recent scientific advances of fundamental interest. An introduction, defining the scope and general nature of T-Division efforts within a given discipline, is followed by articles on the research topics selected. The reporting is done by the scientists involved in the research, and an attempt is made to communicate to a general audience. Some data are given incidentally; more technical presentations of the research accomplished may be found among the 47 pages of references. 110 figures, 5 tables

Prokaryotic cell division: flexible and diverse

NARCIS (Netherlands)

den Blaauwen, T.

2013-01-01

Gram-negative rod-shaped bacteria have different approaches to position the cell division initiating Z-ring at the correct moment in their cell division cycle. The subsequent maturation into a functional division machine occurs in vastly different species in two steps with appreciable time in

Standard Test Method for Saltwater Pressure Immersion and Temperature Testing of Photovoltaic Modules for Marine Environments

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This test method provides a procedure for determining the ability of photovoltaic modules to withstand repeated immersion or splash exposure by seawater as might be encountered when installed in a marine environment, such as a floating aid-to-navigation. A combined environmental cycling exposure with modules repeatedly submerged in simulated saltwater at varying temperatures and under repetitive pressurization provides an accelerated basis for evaluation of aging effects of a marine environment on module materials and construction. 1.2 This test method defines photovoltaic module test specimens and requirements for positioning modules for test, references suitable methods for determining changes in electrical performance and characteristics, and specifies parameters which must be recorded and reported. 1.3 This test method does not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of this test method. 1.4 The values stated in SI units are to be ...

Stratification of the state of Santa Catarina in macro-environments for bean cultivation

Directory of Open Access Journals (Sweden)

Juliano Garcia Bertoldo

2009-01-01

Full Text Available The purpose of this study was to suggest a division of the State of Santa Catarina in macro-environments forexperimentation and bean production. Data of the traits grain yield and plant cycle were evaluated in 10 common beangenotypes grown in nine environments. The data were submitted to the Student-Newman Keuls test, to detect differencesbetween environments, and the Best Linear Unbiased Prediction, to predict the environmental values. The results showed: (adifferences between the regions of Santa Catarina for the traits grain yield and plant cycle, which had a significant positivecorrelation of 0.26 (b Based on the genotypes and environments studied the state can be divided in two macro-environments(MA1 and MA2 and four micro-environments (MI1, MI2, MI3 and MI4. The state of Santa Catarina may be roughly dividedin at least two macro-environments for the recommendation of new cultivars.

Fusion Energy Division progress report, 1 January 1990--31 December 1991

International Nuclear Information System (INIS)

Sheffield, J.; Baker, C.C.; Saltmarsh, M.J.

1994-03-01

The Fusion Program of the Oak Ridge National Laboratory (ORNL), a major part of the national fusion program, encompasses nearly all areas of magnetic fusion research. The program is directed toward the development of fusion as an economical and environmentally attractive energy source for the future. The program involves staff from ORNL, Martin Marietta Energy systems, Inc., private industry, the academic community, and other fusion laboratories, in the US and abroad. Achievements resulting from this collaboration are documented in this report, which is issued as the progress report of the ORNL Fusion Energy Division; it also contains information from components for the Fusion Program that are external to the division (about 15% of the program effort). The areas addressed by the Fusion Program include the following: experimental and theoretical research on magnetic confinement concepts; engineering and physics of existing and planned devices, including remote handling; development and testing of diagnostic tools and techniques in support of experiments; assembly and distribution to the fusion community of databases on atomic physics and radiation effects; development and testing of technologies for heating and fueling fusion plasmas; development and testing of superconducting magnets for containing fusion plasmas; development and testing of materials for fusion devices; and exploration of opportunities to apply the unique skills, technology, and techniques developed in the course of this work to other areas (about 15% of the Division's activities). Highlights from program activities during 1990 and 1991 are presented

Fisheries and the marine environment: policy support and research 1991-92

International Nuclear Information System (INIS)

1993-01-01

This Directorate of Fisheries Report for 1991-2 reviews the work of the Fish Stock Management Division and the Aquatic Environment Protection Division in the fields of control and monitoring of non-radioactive and radioactive waste and of fish and shellfish disease monitoring. (UK)

49 CFR 1242.03 - Made by accounting divisions.

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Made by accounting divisions. 1242.03 Section 1242... accounting divisions. The separation shall be made by accounting divisions, where such divisions are maintained, and the aggregate of the accounting divisions reported for the quarter and for the year. ...

Testing Applications in MANET Environments through Emulation

Directory of Open Access Journals (Sweden)

Pietro Manzoni

2009-01-01

Full Text Available Mobile Ad Hoc Network solution testing is typically done using simulation. The simulated code is generally a simplified version of the real code, and thus code porting to actual operating systems lacks a strong validation. In this work we present Castadiva, a test-bed architecture that allows validating software solutions for real ad hoc network environments using low-cost, off-the-shelf devices and open source software. Castadiva is also compatible with the ns-2 simulator, allowing a combined and more complete evaluation. In this work we present our tool and the results obtained when evaluating videocalls in different scenarios, both static and dynamic.

Environmental and Medical Sciences Division progress report January - December, 1980

International Nuclear Information System (INIS)

Hainge, W.M.

1982-02-01

A progress report on the work performed during 1980 by the Environmental and Medical Sciences Division at UKAEA Harwell is given. The programmes considered were atmospheric pollution; landfill research; monitoring of radioactive fallout and other radionuclides and trace elements in the environment; radioactive and non-radioactive aerosol metabolic studies; inhalation toxicology of radioactive aerosols and other hazardous materials; chemical analytical services; and radiation physics in dosimetry research, applied radiation spectrometry and data systems. (U.K.)

Artificial intelligence in a mission operations and satellite test environment

Science.gov (United States)

Busse, Carl

1988-01-01

A Generic Mission Operations System using Expert System technology to demonstrate the potential of Artificial Intelligence (AI) automated monitor and control functions in a Mission Operations and Satellite Test environment will be developed at the National Aeronautics and Space Administration (NASA) Jet Propulsion Laboratory (JPL). Expert system techniques in a real time operation environment are being studied and applied to science and engineering data processing. Advanced decommutation schemes and intelligent display technology will be examined to develop imaginative improvements in rapid interpretation and distribution of information. The Generic Payload Operations Control Center (GPOCC) will demonstrate improved data handling accuracy, flexibility, and responsiveness in a complex mission environment. The ultimate goal is to automate repetitious mission operations, instrument, and satellite test functions by the applications of expert system technology and artificial intelligence resources and to enhance the level of man-machine sophistication.

2017 T Division Lightning Talks

Energy Technology Data Exchange (ETDEWEB)

Ramsey, Marilyn Leann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Abeywardhana, Jayalath AMM [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Adams, Colin Mackenzie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Adams, Luke Clyde [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carter, Austin Lewis [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ducru, Pablo Philippe [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Duignan, Thomas John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gifford, Brendan Joel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hills, Benjamin Hale [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hoffman, Kentaro Jack [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Khair, Adnan Ibne [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kochanski, Kelly Anne Pribble [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ledwith, Patrick John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Leveillee, Joshua Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lewis, Sina Genevieve [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ma, Xiaoyu [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Merians, Hugh Drake [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Moore, Bryan Alexander [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Nijjar, Parmeet Kaur [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Oles, Vladyslav [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Olszewski, Maciej W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Philipbar, Brad Montgomery [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Reisner, Andrew Ray [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Roberts, David Benjamin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rufa, Dominic Antonio [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Sifain, Andrew E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Smith, Justin Steven [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Smith, Lauren Taylor Wisbey [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Svolos, Lampros [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Thibault, Joshua Ryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ushijima-Mwesigwa, Hayato Montezuma [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Weaver, Claire Marie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Witzen, Wyatt Andrew [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Zentgraf, Sabine Silvia [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Alred, John Michael [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-06

All members of the T Division Community, students, staff members, group leaders, division management, and other interested individuals are invited to come and support the following student(s) as they present their Lightning Talks.

Division: The Sleeping Dragon

Science.gov (United States)

Watson, Anne

2012-01-01

Of the four mathematical operators, division seems to not sit easily for many learners. Division is often described as "the odd one out". Pupils develop coping strategies that enable them to "get away with it". So, problems, misunderstandings, and misconceptions go unresolved perhaps for a lifetime. Why is this? Is it a case of "out of sight out…

E-Division activities report

International Nuclear Information System (INIS)

Barschall, H.H.

1979-07-01

This report describes some of the activities in E (Experimental Physics) Division during the past year. E-Division carries out research and development in areas related to the missions of the Laboratory. Many of the activities are in pure and applied atomic and nuclear physics. In addition, this report describes work on accelerators, radiation damage, microwaves, and plasma diagnostics

Novel Coiled-Coil Cell Division Factor ZapB Stimulates Z Ring Assembly and Cell Division

DEFF Research Database (Denmark)

Ebersbach, Gitte; Galli, Elizabeth; Møller-Jensen, Jakob

2008-01-01

Formation of the Z ring is the first known event in bacterial cell division. However, it is not yet known how the assembly and contraction of the Z ring is regulated. Here, we identify a novel cell division factor ZapB in Escherichia coli that simultaneously stimulates Z ring assembly and cell...... division. Deletion of zapB resulted in delayed cell division and the formation of ectopic Z rings and spirals whereas overexpression of ZapB resulted in nucleoid condensation and aberrant cell divisions. Localization of ZapB to the divisome depended on FtsZ but not FtsA, ZipA or FtsI and ZapB interacted...... with FtsZ in a bacterial two-hybrid analysis. The simultaneous inactivation of FtsA and ZipA prevented Z ring assembly and ZapB localization. Time lapse microscopy showed that ZapB-GFP is present at mid-cell in a pattern very similar to that of FtsZ. Cells carrying a zapB deletion and the ftsZ84ts allele...

Podcast: The Electronic Crimes Division

Science.gov (United States)

Sept 26, 2016. Chris Lukas, the Special Agent in Charge of the Electronic Crimes Division within the OIG's Office of Investigations talks about computer forensics, cybercrime in the EPA and his division's role in criminal investigations.

Corrosion testing of type 304L stainless steel in tuff groundwater environments

International Nuclear Information System (INIS)

Westerman, R.E.; Pitman, S.G.; Haberman, J.H.

1987-11-01

The stress-corrosion cracking (SCC) resistance of Type 304L stainless steel (SS) to elevated temperatures in tuff rock and tuff groundwater environments was determined under irradiated and nonirradiated conditions using U-bend specimens and slow-strain-rate tests. The steel was tested both in the solution-annealed condition and after sensitization heat treatments. The material was found to be susceptible to SCC in both the solution-annealed and solution-annealed-and-sensitized conditions when exposed to an irradiated crushed tuff rock environment containing air and water vapor at 90 0 C. A similar exposure at 50 0 C did not result in failure after a 25-month test duration. Specimens of sensitized 304 SS conditioned with a variety of sensitization heat treatments resisted failure during a test of 1-year duration in which a nonirradiated environment of tuff rock and groundwater held at 200 0 C was allowed to boil to dryness on a cyclical basis. All specimens of sensitized 304 SS exposed to this environment failed. Slow-strain-rate studies were performed on 304L, 304, and 316L SS specimens. The 304L SS was tested in J-13 well water at 150 0 C, and the 316L SS at 95 0 C. Neither material showed evidence of SCC in these tests. Sensitized 304 SS did exhibit SCC in J-13 well water in tests conducted at 150 0 C. 12 refs., 27 figs., 13 tabs

Rotating Arc Jet Test Model: Time-Accurate Trajectory Heat Flux Replication in a Ground Test Environment

Science.gov (United States)

Laub, Bernard; Grinstead, Jay; Dyakonov, Artem; Venkatapathy, Ethiraj

2011-01-01

Though arc jet testing has been the proven method employed for development testing and certification of TPS and TPS instrumentation, the operational aspects of arc jets limit testing to selected, but constant, conditions. Flight, on the other hand, produces timevarying entry conditions in which the heat flux increases, peaks, and recedes as a vehicle descends through an atmosphere. As a result, we are unable to "test as we fly." Attempts to replicate the time-dependent aerothermal environment of atmospheric entry by varying the arc jet facility operating conditions during a test have proven to be difficult, expensive, and only partially successful. A promising alternative is to rotate the test model exposed to a constant-condition arc jet flow to yield a time-varying test condition at a point on a test article (Fig. 1). The model shape and rotation rate can be engineered so that the heat flux at a point on the model replicates the predicted profile for a particular point on a flight vehicle. This simple concept will enable, for example, calibration of the TPS sensors on the Mars Science Laboratory (MSL) aeroshell for anticipated flight environments.

Chemical Technology Division annual technical report, 1986

Energy Technology Data Exchange (ETDEWEB)

1987-06-01

Highlights of the Chemical Technology (CMT) Division's activities during 1986 are presented. In this period, CMT conducted research and development in areas that include the following: (1) high-performance batteries - mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants, the technology for fluidized-bed combustion, and a novel concept for CO/sub 2/ recovery from fossil fuel combustion; (5) methods for recovery of energy from municipal waste; (6) methods for the electromagnetic continuous casting of steel sheet; (7) techniques for treatment of hazardous waste such as reactive metals and trichloroethylenes; (8) nuclear technology related to waste management, a process for separating and recovering transuranic elements from nuclear waste, and the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor; and (9) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of catalytic hydrogenation and catalytic oxidation; materials chemistry for associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, surface science, and catalysis; the thermochemistry of zeolites and related silicates; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 127 refs., 71 figs., 8 tabs.

Interdependence of bacterial cell division and genome segregation and its potential in drug development.

Science.gov (United States)

Misra, Hari S; Maurya, Ganesh K; Chaudhary, Reema; Misra, Chitra S

2018-03-01

Cell division and genome segregation are mutually interdependent processes, which are tightly linked with bacterial multiplication. Mechanisms underlying cell division and the cellular machinery involved are largely conserved across bacteria. Segregation of genome elements on the other hand, follows different pathways depending upon its type and the functional components encoded on these elements. Small molecules, that are known to inhibit cell division and/or resolution of intertwined circular chromosome and maintenace of DNA topology have earlier been tested as antibacterial agents. The utility of such drugs in controlling bacterial infections has witnessed only partial success, possibly due to functional redundancy associated with targeted components. However, in due course, literature has grown with newer information. This review has brought forth some recent findings on bacterial cell division with special emphasis on crosstalk between cell division and genome segregation that could be explored as novel targets in drug development. Copyright © 2018 Elsevier GmbH. All rights reserved.

Chlamydia co-opts the rod shape-determining proteins MreB and Pbp2 for cell division.

Science.gov (United States)

Ouellette, Scot P; Karimova, Gouzel; Subtil, Agathe; Ladant, Daniel

2012-07-01

Chlamydiae are obligate intracellular bacterial pathogens that have extensively reduced their genome in adapting to the intracellular environment. The chlamydial genome contains only three annotated cell division genes and lacks ftsZ. How this obligate intracellular pathogen divides is uncharacterized. Chlamydiae contain two high-molecular-weight (HMW) penicillin binding proteins (Pbp) implicated in peptidoglycan synthesis, Pbp2 and Pbp3/FtsI. We show here, using HMW Pbp-specific penicillin derivatives, that both Pbp2 and Pbp3 are essential for chlamydial cell division. Ultrastructural analyses of antibiotic-treated cultures revealed distinct phenotypes: Pbp2 inhibition induced internal cell bodies within a single outer membrane whereas Pbp3 inhibition induced elongated phenotypes with little internal division. Each HMW Pbp interacts with the Chlamydia cell division protein FtsK. Chlamydiae are coccoid yet contain MreB, a rod shape-determining protein linked to Pbp2 in bacilli. Using MreB-specific antibiotics, we show that MreB is essential for chlamydial growth and division. Importantly, co-treatment with MreB-specific and Pbp-specific antibiotics resulted in the MreB-inhibited phenotype, placing MreB upstream of Pbp function in chlamydial cell division. Finally, we showed that MreB also interacts with FtsK. We propose that, in Chlamydia, MreB acts as a central co-ordinator at the division site to substitute for the lack of FtsZ in this bacterium. © 2012 Blackwell Publishing Ltd.

Spectroscopy Division : Progress report for Oct 1979 - Dec 1980

International Nuclear Information System (INIS)

Saksena, G.D.; Naik, R.C.

1981-01-01

An account of the activities, with an individual summary of each, of the Spectroscopy Division of the Bhabha Atomic Research Centre (BARC), Bombay, for the period from October 1979 to December 1980 is given. The activities of the Division are mainly concerned with: (1) spectrochemical analysis of nuclear fuels, reactor materials, mineral samples, environmental samples, biological samples, and other samples by methods of optical emission spectroscopy, electron spectroscopy, and X-ray fluorescence spectroscopy, (2) research and development primarily in the field of high resolution atomic and molecular spectroscopy, and (3) design and fabrication of high precision optical instruments and electronic components for other Divisions of BARC and other constituent units of the Department of Atomic Energy. During the report period, the following were fabricated: a monochromator using a concave holographic grating, a holographic grating spectrograph, a core viewing system for the Fast Breeder Test Reactor now under construction at Kalpakkam, a critical angle refractometer for heavy water analysis in the Rajasthan Atomic Power Station, electronic equipment like frequency divider amplifier, lock-in-voltmeter, analog ratio meter etc. required for laser spectroscopy. Lists of the staff members, their publications during the report period, educational and training activities of the Division are also given. Two feature articles, one dealing with beam foil spectroscopy and the other with monochromatization of synchrotron radiation, are also included. (M.G.B.)

Division of Integrity and Materials

International Nuclear Information System (INIS)

Zdarek, J.

1995-01-01

The organization structure is described of the Division of Integrity and Materials, Institute of Nuclear Research plc, Rez, and the main fields of their activities given. Listed are the major research projects of the Division in 1994. (Z.S.)

2016 T Division Lightning Talks

Energy Technology Data Exchange (ETDEWEB)

Ramsey, Marilyn Leann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Adams, Luke Clyde [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Ferre, Gregoire Robing [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Grantcharov, Vesselin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Iaroshenko, Oleksandr [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Krishnapriyan, Aditi [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Kurtakoti, Prajvala Kishore [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Le Thien, Minh Quan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Lim, Jonathan Ng [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Low, Thaddeus Song En [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Lystrom, Levi Aaron [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Ma, Xiaoyu [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Nguyen, Hong T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Pogue, Sabine Silvia [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Orandle, Zoe Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Reisner, Andrew Ray [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Revard, Benjamin Charles [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Roy, Julien [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Sandor, Csanad [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Slavkova, Kalina Polet [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Weichman, Kathleen Joy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Wu, Fei [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Yang, Yang [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division

2016-11-29

These are the slides for all of the 2016 T Division lightning talks. There are 350 pages worth of slides from different presentations, all of which cover different topics within the theoretical division at Los Alamos National Laboratory (LANL).

Physics Division progress report, October 1, 1986--September 30, 1987

International Nuclear Information System (INIS)

Shera, E.B.; Sowerwine, H.

1989-05-01

This report provides brief accounts of significant progress in development activities and research results achieved by Physics Division personnel during the period October 1, 1986 through September 30, 1987. These efforts are representative of the three main areas of experimental research and development in which the Physics Division serves Los Alamos National Laboratory's and the nation's needs in defense and basic sciences: defense physics, including the development of diagnostic methods for weapons tests, weapon-related high-energy-density physics, and programs supporting the Strategic Defense Initiative; laser physics and applications, especially to high-density plasmas; and fundamental research in nuclear and particle physics, condensed-matter physics, and biophysics. Throughout the report, emphasis is placed on the design, construction, and application of a variety of advanced, often unique, instruments and instrument systems that maintain the Division's position at the leading edge of research and development in the specific fields germane to its mission

Analytical Chemistry Division's sample transaction system

International Nuclear Information System (INIS)

Stanton, J.S.; Tilson, P.A.

1980-10-01

The Analytical Chemistry Division uses the DECsystem-10 computer for a wide range of tasks: sample management, timekeeping, quality assurance, and data calculation. This document describes the features and operating characteristics of many of the computer programs used by the Division. The descriptions are divided into chapters which cover all of the information about one aspect of the Analytical Chemistry Division's computer processing

Optical Code-Division Multiple-Access and Wavelength Division Multiplexing: Hybrid Scheme Review

OpenAIRE

P. Susthitha Menon; Sahbudin Shaari; Isaac A.M. Ashour; Hesham A. Bakarman

2012-01-01

Problem statement: Hybrid Optical Code-Division Multiple-Access (OCDMA) and Wavelength-Division Multiplexing (WDM) have flourished as successful schemes for expanding the transmission capacity as well as enhancing the security for OCDMA. However, a comprehensive review related to this hybrid system are lacking currently. Approach: The purpose of this paper is to review the literature on OCDMA-WDM overlay systems, including our hybrid approach of one-dimensional coding of SAC OCDMA with WDM si...

Space Launch System Base Heating Test: Environments and Base Flow Physics

Science.gov (United States)

Mehta, Manish; Knox, Kyle S.; Seaford, C. Mark; Dufrene, Aaron T.

2016-01-01

The NASA Space Launch System (SLS) vehicle is composed of four RS-25 liquid oxygen- hydrogen rocket engines in the core-stage and two 5-segment solid rocket boosters and as a result six hot supersonic plumes interact within the aft section of the vehicle during ight. Due to the complex nature of rocket plume-induced ows within the launch vehicle base during ascent and a new vehicle con guration, sub-scale wind tunnel testing is required to reduce SLS base convective environment uncertainty and design risk levels. This hot- re test program was conducted at the CUBRC Large Energy National Shock (LENS) II short-duration test facility to simulate ight from altitudes of 50 kft to 210 kft. The test program is a challenging and innovative e ort that has not been attempted in 40+ years for a NASA vehicle. This presentation discusses the various trends of base convective heat ux and pressure as a function of altitude at various locations within the core-stage and booster base regions of the two-percent SLS wind tunnel model. In-depth understanding of the base ow physics is presented using the test data, infrared high-speed imaging and theory. The normalized test design environments are compared to various NASA semi- empirical numerical models to determine exceedance and conservatism of the ight scaled test-derived base design environments. Brief discussion of thermal impact to the launch vehicle base components is also presented.

Chemical Technology Division annual technical report 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials and electrified interfaces. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division`s activities during 1997 are presented.

Reducing test-data volume and test-power simultaneously in LFSR reseeding-based compression environment

Energy Technology Data Exchange (ETDEWEB)

Wang Weizheng; Kuang Jishun; You Zhiqiang; Liu Peng, E-mail: jshkuang@163.com [College of Information Science and Engineering, Hunan University, Changsha 410082 (China)

2011-07-15

This paper presents a new test scheme based on scan block encoding in a linear feedback shift register (LFSR) reseeding-based compression environment. Meanwhile, our paper also introduces a novel algorithm of scan-block clustering. The main contribution of this paper is a flexible test-application framework that achieves significant reductions in switching activity during scan shift and the number of specified bits that need to be generated via LFSR reseeding. Thus, it can significantly reduce the test power and test data volume. Experimental results using Mintest test set on the larger ISCAS'89 benchmarks show that the proposed method reduces the switching activity significantly by 72%-94% and provides a best possible test compression of 74%-94% with little hardware overhead. (semiconductor integrated circuits)

Lightning Talks 2015: Theoretical Division

Energy Technology Data Exchange (ETDEWEB)

Shlachter, Jack S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-11-25

This document is a compilation of slides from a number of student presentations given to LANL Theoretical Division members. The subjects cover the range of activities of the Division, including plasma physics, environmental issues, materials research, bacterial resistance to antibiotics, and computational methods.

Developmental control of cell division

NARCIS (Netherlands)

Boxem, M. (Mike)

2002-01-01

During development of multicellular organisms, cell divisions need to be coordinated with the developmental program of the entire organism. Although the mechanisms that drive cells through the division cycle are well understood, very little is known about the pathways that link extracellular signals

Testing Algorithmic Skills in Traditional and Non-Traditional Programming Environments

Science.gov (United States)

Csernoch, Mária; Biró, Piroska; Máth, János; Abari, Kálmán

2015-01-01

The Testing Algorithmic and Application Skills (TAaAS) project was launched in the 2011/2012 academic year to test first year students of Informatics, focusing on their algorithmic skills in traditional and non-traditional programming environments, and on the transference of their knowledge of Informatics from secondary to tertiary education. The…

Simple test guidelines for screening oilspill sorbents for toxicity

International Nuclear Information System (INIS)

Blenkinsopp, S.A.; Sergy, G.; Doe, K.; Jackman, P.; Huybers, A.

1998-01-01

Environment Canada's Emergencies Science Division has established a program to develop a standard test method suitable for evaluating the toxicity of common sorbent materials. Sorbents are used to absorb or adsorb spilled oil and other hazardous materials. They vary widely in composition and packaging. They are often treated with oleophilic and hydrophobic compounds to improve performance and have been used in large quantities during oil spills. Until now, their potential toxicity has never been considered. Three tests have been evaluated to determine how appropriate they are in screening the toxicity of sorbents. Seven toxicity test recommendations for sorbents were presented. 7 refs., 3 tabs., 2 figs

Genotype-by-Environment Interaction and Testing Environments for Plantain and Banana (Musa spp. L. Breeding in West Africa

Directory of Open Access Journals (Sweden)

Ortiz, R.

1999-01-01

Full Text Available With reduced budgets allocated for international agricultural research, site rationalisation had become an important issue to consider when carrying out multilocational testing of promising selections. The aim of this paper was to determine the importance of the genotype-by-environment interaction in multilocational trials of plantains and bananas (Musa spp. L. in selected sites of West Africa comprising the humid forest and the forest-savanna transition zones. A sample of plantain-banana hybrids, plantain landraces, exotic banana cultivars and diploid parental banana accessions were evaluated in three locations : Mbalmayo and Onne (humid forest and Ibadan (forest-savanna transition. The experimental results of our research suggested that multilocational testing is more profitable than single site evaluation over several years in the Musa breeding station. Furthermore, based on correlated responses across environments for yield potential, we suggest that one of the selection sites in the humid forest (i. e., Mbalmayo be dropped since selections in one site (Onne may be well adapted to the other location in the same agroecozone. Conversely, the relatively poor performance of most genotypes in dry environments (e. g. Ibadan reinforces the importance of early testing across a wide range of environments. In this way selections with broad or specific adaptation may be identified for further release to targeted farmers.

Design of a Realistic Test Simulator For a Built-In Self Test Environment

Directory of Open Access Journals (Sweden)

A. Ahmad

2010-12-01

Full Text Available This paper presents a realistic test approach suitable to Design For Testability (DFT and Built- In Self Test (BIST environments. The approach is culminated in the form of a test simulator which is capable of providing a required goal of test for the System Under Test (SUT. The simulator uses the approach of fault diagnostics with fault grading procedure to provide the tests. The tool is developed on a common PC platform and hence no special software is required. Thereby, it is a low cost tool and hence economical. The tool is very much suitable for determining realistic test sequences for a targeted goal of testing for any SUT. The developed tool incorporates a flexible Graphical User Interface (GUI procedure and can be operated without any special programming skill. The tool is debugged and tested with the results of many bench mark circuits. Further, this developed tool can be utilized for educational purposes for many courses such as fault-tolerant computing, fault diagnosis, digital electronics, and safe - reliable - testable digital logic designs.

Space Suit Portable Life Support System (PLSS) 2.0 Unmanned Vacuum Environment Testing

Science.gov (United States)

Watts, Carly; Vogel, Matthew

2016-01-01

For the first time in more than 30 years, an advanced space suit Portable Life Support System (PLSS) design was operated inside a vacuum chamber representative of the flight operating environment. The test article, PLSS 2.0, was the second system-level integrated prototype of the advanced PLSS design, following the PLSS 1.0 Breadboard that was developed and tested throughout 2011. Whereas PLSS 1.0 included five technology development components with the balance the system simulated using commercial-off-the-shelf items, PLSS 2.0 featured first generation or later prototypes for all components less instrumentation, tubing and fittings. Developed throughout 2012, PLSS 2.0 was the first attempt to package the system into a flight-like representative volume. PLSS 2.0 testing included an extensive functional evaluation known as Pre-Installation Acceptance (PIA) testing, Human-in-the-Loop testing in which the PLSS 2.0 prototype was integrated via umbilicals to a manned prototype space suit for 19 two-hour simulated EVAs, and unmanned vacuum environment testing. Unmanned vacuum environment testing took place from 1/9/15-7/9/15 with PLSS 2.0 located inside a vacuum chamber. Test sequences included performance mapping of several components, carbon dioxide removal evaluations at simulated intravehicular activity (IVA) conditions, a regulator pressure schedule assessment, and culminated with 25 simulated extravehicular activities (EVAs). During the unmanned vacuum environment test series, PLSS 2.0 accumulated 378 hours of integrated testing including 291 hours of operation in a vacuum environment and 199 hours of simulated EVA time. The PLSS prototype performed nominally throughout the test series, with two notable exceptions including a pump failure and a Spacesuit Water Membrane Evaporator (SWME) leak, for which post-test failure investigations were performed. In addition to generating an extensive database of PLSS 2.0 performance data, achievements included requirements and

Chemical Technology Division annual technical report, 1994

International Nuclear Information System (INIS)

1995-06-01

Highlights of the Chemical Technology (CMT) Division's activities during 1994 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion; (3) methods for treatment of hazardous waste and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from waste streams, concentrating radioactive waste streams with advanced evaporator technology, and producing 99 Mo from low-enriched uranium for medical applications; (6) electrometallurgical treatment of the many different types of spent nuclear fuel in storage at Department of Energy sites; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, molecular sieve structures, and impurities in scrap copper and steel; and the geochemical processes involved in mineral/fluid interfaces and water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL)

Chemical Technology Division, Annual technical report, 1991

International Nuclear Information System (INIS)

1992-03-01

Highlights of the Chemical Technology (CMT) Division's activities during 1991 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion and coal-fired magnetohydrodynamics; (3) methods for treatment of hazardous and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources; chemistry of superconducting oxides and other materials of interest with technological application; interfacial processes of importance to corrosion science, catalysis, and high-temperature superconductivity; and the geochemical processes involved in water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL)

Chemical Technology Division, Annual technical report, 1991

Energy Technology Data Exchange (ETDEWEB)

1992-03-01

Highlights of the Chemical Technology (CMT) Division's activities during 1991 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion and coal-fired magnetohydrodynamics; (3) methods for treatment of hazardous and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources; chemistry of superconducting oxides and other materials of interest with technological application; interfacial processes of importance to corrosion science, catalysis, and high-temperature superconductivity; and the geochemical processes involved in water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL).

E-Division activities report

International Nuclear Information System (INIS)

Barschall, H.H.

1981-07-01

This report describes some of the activities in E (Experimental Physics) Division during the past year. E-Division carries out research and development in areas related to the missions of the Laboratory. Many of the activities are in pure and applied atomic and nuclear physics and in material science. In addition this report describes work on accelerators, microwaves, plasma diagnostics, determination of atmospheric oxygen and of nitrogen in tissue

Instrumentation and Controls Division annual progress report for period ending September 1, 1973

International Nuclear Information System (INIS)

Sadowski, G.S.

1976-08-01

Research progress is described under the following topics: (1) pulse counting and analysis; (2) support for the thermonuclear division ORMAK project; (3) miscellaneous electronics development; (4) detectors of ionizing particles and radiation; (5) radiation monitoring; (6) support for the Oak Ridge Electron Linear Accelerator; (7) automatic control and data acquisition; (8) process instrumentation and control; (9) reactor instrumentation and controls; (10) instrumentation for reactor division experiments and test loops; (11) maintenance and service; and (12) ecological science studies

Engineering Physics Division integral experiments and their analyses

International Nuclear Information System (INIS)

Anon.

1980-01-01

Integral experiments are performed as part of the Engineering Physics Division's on-going research in the development and application of radiation shielding methods. Integral experiments performed at the Oak Ridge Electron Linear Accelerator (ORELA) under the Division's Magnetic Fusion program are designed to provide data against which ORNL and all other organizations involved in shielding calculations for fusion devices can test their calculational methods and interaction data. The Tower Shielding Facility (TSF) continues to be the primary source of integral data for fission reactor shielding design. The experiments performed at the TSF during the last few years have been sponsored by the Gas Cooled Fast Reactor (GCFR) program. During this report period final documentation was also prepared for the remaining LMFBR shielding experiments, including an examination of streaming through annular slits and measurement of secondary gamma-ray production in reinforced concrete

Some new fatigue tests in high temperature water and liquid sodium environment

International Nuclear Information System (INIS)

Hattori, Takahiro; Yamauchi, Takayoshi; Kanasaki, Hiroshi; Kondo, Yoshiyuki; Endo, Tadayoshi.

1987-01-01

To evaluate the fatigue strength of structural materials for PWR or FBR plants, fatigue test data must be obtained in an environment of simulated primary and secondary water for PWR or of high temperature liquid sodium for FBR. Generally, such tests make it necessary to prepare expensive facilities, so when large amount of fatigue data are required, it is necessary to rationalize and simplify the fatigue tests while maintaining high accuracy. At the Takasago Research Development Center, efforts to rationalize facilities and maintain accuracy in fatigue tests have been made by developing new test methods and improving conventional techniques. This paper introduces a new method of low cycle fatigue test in high temperature water, techniques for automatic measurement of crack initiation and propagation in high temperature water environment and a multiple type fatigue testing machine for high temperature liquid sodium. (author)

Physics division annual report - 1999

International Nuclear Information System (INIS)

Thayer, K.

2000-01-01

This report summarizes the research performed in the past year in the Argonne Physics Division. The Division's programs include operation of ATLAS as a national heavy-ion user facility, nuclear structure and reaction research with beams of heavy ions, accelerator research and development especially in superconducting radio frequency technology, nuclear theory and medium energy nuclear physics. The Division took significant strides forward in its science and its initiatives for the future in the past year. Major progress was made in developing the concept and the technology for the future advanced facility of beams of short-lived nuclei, the Rare Isotope Accelerator. The scientific program capitalized on important instrumentation initiatives with key advances in nuclear science. In 1999, the nuclear science community adopted the Argonne concept for a multi-beam superconducting linear accelerator driver as the design of choice for the next major facility in the field a Rare Isotope Accelerator (RIA) as recommended by the Nuclear Science Advisory Committee's 1996 Long Range Plan. Argonne has made significant R and D progress on almost all aspects of the design concept including the fast gas catcher (to allow fast fragmentation beams to be stopped and reaccelerated) that in large part, defined the RIA concept the superconducting rf technology for the driver accelerator, the multiple-charge-state concept (to permit the facility to meet the design intensity goals with existing ion-source technology), and designs and tests of high-power target concepts to effectively deal with the full beam power of the driver linac. An NSAC subcommittee recommended the Argonne concept and set as tie design goal Uranium beams of 100-kwatt power at 400 MeV/u. Argonne demonstrated that this goal can be met with an innovative, but technically in-hand, design

Chemical Sciences Division: Annual report 1992

International Nuclear Information System (INIS)

1993-10-01

The Chemical Sciences Division (CSD) is one of twelve research Divisions of the Lawrence Berkeley Laboratory, a Department of Energy National Laboratory. The CSD is composed of individual groups and research programs that are organized into five scientific areas: Chemical Physics, Inorganic/Organometallic Chemistry, Actinide Chemistry, Atomic Physics, and Physical Chemistry. This report describes progress by the CSD for 1992. Also included are remarks by the Division Director, a description of work for others (United States Office of Naval Research), and appendices of the Division personnel and an index of investigators. Research reports are grouped as Fundamental Interactions (Photochemical and Radiation Sciences, Chemical Physics, Atomic Physics) or Processes and Techniques (Chemical Energy, Heavy-Element Chemistry, and Chemical Engineering Sciences)

Materials and Components Technology Division research summary, 1991

International Nuclear Information System (INIS)

1991-04-01

This division has the purpose of providing a R and D capability for design, fabrication, and testing of high-reliability materials, components, and instrumentation. Current divisional programs are in support of the Integral Fast Reactor, life extension for light water reactors, fuels development for the new production reactor and research and test reactors, fusion reactor first-wall and blanket technology, safe shipment of hazardous materials, fluid mechanics/materials/instrumentation for fossile energy systems, and energy conservation and renewables (including tribology, high- temperature superconductivity). Separate abstracts have been prepared for the data base

Materials and Components Technology Division research summary, 1991

Energy Technology Data Exchange (ETDEWEB)

1991-04-01

This division has the purpose of providing a R and D capability for design, fabrication, and testing of high-reliability materials, components, and instrumentation. Current divisional programs are in support of the Integral Fast Reactor, life extension for light water reactors, fuels development for the new production reactor and research and test reactors, fusion reactor first-wall and blanket technology, safe shipment of hazardous materials, fluid mechanics/materials/instrumentation for fossile energy systems, and energy conservation and renewables (including tribology, high- temperature superconductivity). Separate abstracts have been prepared for the data base.

Aliphatic hydrocarbons in surface sediments from South China Sea off Kuching Division, Sarawak

International Nuclear Information System (INIS)

Hafidz Yusoff; Zaini Assim; Samsur Mohamad

2012-01-01

Eighteen surface sediment samples collected from South China Sea off Kuching Division, Sarawak were analyzed for aliphatic hydrocarbons. These hydrocarbons were recovered from sediment by Soxhlet extraction method and then analyzed using gas chromatography equipped with mass spectrometer (GC/ MS). Total concentrations of aliphatic hydrocarbons in surface sediments from South China Sea off Kuching division are ranged from 35.6 μg/ g to 1466.1 μg/ g dry weights. The sediments collected from Bako Bay, Kuching showed high concentrations of total aliphatic hydrocarbons. Several molecular indices were used to predict the predominant sources of hydrocarbons. Carbon preference index (CPI) value revealed widespread anthropogenic input in this study area (CPI= 0 to 4.1). The ratio of C 31 / C 19 and C 29 / C 31 indicated that major input of aliphatic hydrocarbon mostly transfer by lateral input to the marine environment than atmospheric movements. Generally, the concentrations of aliphatic hydrocarbons in sediment from South China Sea off Kuching division are generally higher compare to other area in the world. (author)

Periplasmic Acid Stress Increases Cell Division Asymmetry (Polar Aging of Escherichia coli.

Directory of Open Access Journals (Sweden)

Michelle W Clark

Full Text Available Under certain kinds of cytoplasmic stress, Escherichia coli selectively reproduce by distributing the newer cytoplasmic components to new-pole cells while sequestering older, damaged components in cells inheriting the old pole. This phenomenon is termed polar aging or cell division asymmetry. It is unknown whether cell division asymmetry can arise from a periplasmic stress, such as the stress of extracellular acid, which is mediated by the periplasm. We tested the effect of periplasmic acid stress on growth and division of adherent single cells. We tracked individual cell lineages over five or more generations, using fluorescence microscopy with ratiometric pHluorin to measure cytoplasmic pH. Adherent colonies were perfused continually with LBK medium buffered at pH 6.00 or at pH 7.50; the external pH determines periplasmic pH. In each experiment, cell lineages were mapped to correlate division time, pole age and cell generation number. In colonies perfused at pH 6.0, the cells inheriting the oldest pole divided significantly more slowly than the cells inheriting the newest pole. In colonies perfused at pH 7.50 (near or above cytoplasmic pH, no significant cell division asymmetry was observed. Under both conditions (periplasmic pH 6.0 or pH 7.5 the cells maintained cytoplasmic pH values at 7.2-7.3. No evidence of cytoplasmic protein aggregation was seen. Thus, periplasmic acid stress leads to cell division asymmetry with minimal cytoplasmic stress.

Insights into the Mechanisms of Chloroplast Division

Directory of Open Access Journals (Sweden)

Yamato Yoshida

2018-03-01

Full Text Available The endosymbiosis of a free-living cyanobacterium into an ancestral eukaryote led to the evolution of the chloroplast (plastid more than one billion years ago. Given their independent origins, plastid proliferation is restricted to the binary fission of pre-existing plastids within a cell. In the last 25 years, the structure of the supramolecular machinery regulating plastid division has been discovered, and some of its component proteins identified. More recently, isolated plastid-division machineries have been examined to elucidate their structural and mechanistic details. Furthermore, complex studies have revealed how the plastid-division machinery morphologically transforms during plastid division, and which of its component proteins play a critical role in generating the contractile force. Identifying the three-dimensional structures and putative functional domains of the component proteins has given us hints about the mechanisms driving the machinery. Surprisingly, the mechanisms driving plastid division resemble those of mitochondrial division, indicating that these division machineries likely developed from the same evolutionary origin, providing a key insight into how endosymbiotic organelles were established. These findings have opened new avenues of research into organelle proliferation mechanisms and the evolution of organelles.

Physics Division progress report, Special 50th anniversary issue, January 1, 1992--December 31, 1992

International Nuclear Information System (INIS)

Shera, E.B.; Hollen, G.Y.

1993-01-01

This special anniversary issue of the Physics Division progress report presents a series of articles that describe the missions and projects of the past and present Physics Division Leaders during their respective tenures. The report also includes selected accounts of significant progress in research and development achieved by Physics Division personnel during the period January 1, 1992, through December 31, 1992, a general description of the goals and interests of the Division, and a list of publications produced during this period. The report represents the three main areas of experimental research and development in which the Physics Division serves the needs of Los Alamos National Laboratory and the nation in defense and basic sciences: (1) fundamental research in nuclear and particle physics, condensed-matter physics, and biophysics; (2) laser physics and applications, especially to high-density plasmas; and (3) defense physics, including the development of diagnostic methods for weapons tests, weapons-related high energy-density physics, and other programs

The 1988 Leti Division progress report

International Nuclear Information System (INIS)

Anon.

1988-01-01

The 1988 progress report of the CEA's LETI Division (Division of Electronics, Technology and Instrumentation, France) is presented. The missions of LETI Division involve military and nuclear applications of electronics and fundamental research. The research programs developed in 1988 are the following: materials and components, non-volatile silicon memories, silicon-over-insulator, integrated circuits technologies, common experimental laboratory (opened to the European community), mass memories, photodetectors, micron sensors and flat screens [fr

Space Environment Testing of Photovoltaic Array Systems at NASA's Marshall Space Flight Center

Science.gov (United States)

Phillips, Brandon S.; Schneider, Todd A.; Vaughn, Jason A.; Wright, Kenneth H., Jr.

2015-01-01

To successfully operate a photovoltaic (PV) array system in space requires planning and testing to account for the effects of the space environment. It is critical to understand space environment interactions not only on the PV components, but also the array substrate materials, wiring harnesses, connectors, and protection circuitry (e.g. blocking diodes). Key elements of the space environment which must be accounted for in a PV system design include: Solar Photon Radiation, Charged Particle Radiation, Plasma, and Thermal Cycling. While solar photon radiation is central to generating power in PV systems, the complete spectrum includes short wavelength ultraviolet components, which photo-ionize materials, as well as long wavelength infrared which heat materials. High energy electron radiation has been demonstrated to significantly reduce the output power of III-V type PV cells; and proton radiation damages material surfaces - often impacting coverglasses and antireflective coatings. Plasma environments influence electrostatic charging of PV array materials, and must be understood to ensure that long duration arcs do not form and potentially destroy PV cells. Thermal cycling impacts all components on a PV array by inducing stresses due to thermal expansion and contraction. Given such demanding environments, and the complexity of structures and materials that form a PV array system, mission success can only be ensured through realistic testing in the laboratory. NASA's Marshall Space Flight Center has developed a broad space environment test capability to allow PV array designers and manufacturers to verify their system's integrity and avoid costly on-orbit failures. The Marshall Space Flight Center test capabilities are available to government, commercial, and university customers. Test solutions are tailored to meet the customer's needs, and can include performance assessments, such as flash testing in the case of PV cells.

Energy Division annual progress report for period ending September 30, 1983

Energy Technology Data Exchange (ETDEWEB)

1984-06-01

This report covers work done during FY 1983 by the staff of the Energy Division and its subcontractors and by colleagues in other Oak Ridge National Laboratory divisions working on Energy Division projects. The work can be divided into four areas: (1) analysis and assessment, (2) models and data systems, (3) research to improve the efficiency of energy use and to improve electric power transmission and distribution, and (4) research utilization. Support came principally from the US Department of Energy (DOE), the US Nuclear Regulatory Commission, and the US Department of Defense, but also from a number of other agencies and organizations. Analysis and assessment included work on (a) environmental issues, including those deriving from the preparation of environmental impact statements; (b) energy and resource analysis; and (c) emergency preparedness. The models and data systems area involved research on evaluating and developing energy, environment, and engineering simulation models and on devising large data management systems, evaluating user data requirements, and compiling data bases. Research on improving the efficiency of energy use was focused primarily on the buildings and electricity sectors. A major effort on heat pump technology, which includes both heat-activated and electrically driven systems, continues. An important aspect of all the work was research utilization. Since the Energy Division is doing applied research, results are, by definition, intended to solve problems or answer questions of DOE and other sponsors. However, there are other users, and research utilization activities include technology transfer, commercialization efforts, outreach to state and regional organizations, and, of course, information dissemination.

Energy Division annual progress report for period ending September 30, 1983

International Nuclear Information System (INIS)

1984-06-01

This report covers work done during FY 1983 by the staff of the Energy Division and its subcontractors and by colleagues in other Oak Ridge National Laboratory divisions working on Energy Division projects. The work can be divided into four areas: (1) analysis and assessment, (2) models and data systems, (3) research to improve the efficiency of energy use and to improve electric power transmission and distribution, and (4) research utilization. Support came principally from the US Department of Energy (DOE), the US Nuclear Regulatory Commission, and the US Department of Defense, but also from a number of other agencies and organizations. Analysis and assessment included work on (a) environmental issues, including those deriving from the preparation of environmental impact statements; (b) energy and resource analysis; and (c) emergency preparedness. The models and data systems area involved research on evaluating and developing energy, environment, and engineering simulation models and on devising large data management systems, evaluating user data requirements, and compiling data bases. Research on improving the efficiency of energy use was focused primarily on the buildings and electricity sectors. A major effort on heat pump technology, which includes both heat-activated and electrically driven systems, continues. An important aspect of all the work was research utilization. Since the Energy Division is doing applied research, results are, by definition, intended to solve problems or answer questions of DOE and other sponsors. However, there are other users, and research utilization activities include technology transfer, commercialization efforts, outreach to state and regional organizations, and, of course, information dissemination

Division of labor associated with brood rearing in the honey bee: how does it translate to colony fitness?

Directory of Open Access Journals (Sweden)

Ramesh R Sagili

2011-02-01

Full Text Available Division of labor is a striking feature observed in honey bees and many other social insects. Division of labor has been claimed to benefit fitness. In honey bees, the adult work force may be viewed as divided between non-foraging hive bees that rear brood and maintain the nest, and foragers that collect food outside the nest. Honey bee brood pheromone is a larval pheromone that serves as an excellent empirical tool to manipulate foraging behaviors and thus division of labor in the honey bee. Here we use two different doses of brood pheromone to alter the foraging stimulus environment, thus changing demographics of colony division of labor, to demonstrate how division of labor associated with brood rearing affects colony growth rate. We examine the effects of these different doses of brood pheromone on individual foraging ontogeny and specialization, colony level foraging behavior, and individual glandular protein synthesis. Low brood pheromone treatment colonies exhibited significantly higher foraging population, decreased age of first foraging and greater foraging effort, resulting in greater colony growth compared to other treatments. This study demonstrates how division of labor associated with brood rearing affects honey bee colony growth rate, a token of fitness.

Physics division annual report 2006.

Energy Technology Data Exchange (ETDEWEB)

Glover, J.; Physics

2008-02-28

This report highlights the activities of the Physics Division of Argonne National Laboratory in 2006. The Division's programs include the operation as a national user facility of ATLAS, the Argonne Tandem Linear Accelerator System, research in nuclear structure and reactions, nuclear astrophysics, nuclear theory, investigations in medium-energy nuclear physics as well as research and development in accelerator technology. The mission of nuclear physics is to understand the origin, evolution and structure of baryonic matter in the universe--the core of matter, the fuel of stars, and the basic constituent of life itself. The Division's research focuses on innovative new ways to address this mission.

Relationships and Predictive Capabilities of Jump Assessments to Soccer-Specific Field Test Performance in Division I Collegiate Players.

Science.gov (United States)

Lockie, Robert G; Stage, Alyssa A; Stokes, John J; Orjalo, Ashley J; Davis, DeShaun L; Giuliano, Dominic V; Moreno, Matthew R; Risso, Fabrice G; Lazar, Adrina; Birmingham-Babauta, Samantha A; Tomita, Tricia M

2016-12-03

Leg power is an important characteristic for soccer, and jump tests can measure this capacity. Limited research has analyzed relationships between jumping and soccer-specific field test performance in collegiate male players. Nineteen Division I players completed tests of: leg power (vertical jump (VJ), standing broad jump (SBJ), left- and right-leg triple hop (TH)); linear (30 m sprint; 0⁻5 m, 5⁻10 m, 0⁻10, 0⁻30 m intervals) and change-of-direction (505) speed; soccer-specific fitness (Yo-Yo Intermittent Recovery Test Level 2); and 7 × 30-m sprints to measure repeated-sprint ability (RSA; total time (TT), performance decrement (PD)). Pearson's correlations ( r ) determined jump and field test relationships; stepwise regression ascertained jump predictors of the tests ( p jumps correlated with the 0⁻5, 0⁻10, and 0⁻30 m sprint intervals ( r = -0.65⁻-0.90). VJ, SBJ, and left- and right-leg TH correlated with RSA TT ( r = -0.51⁻-0.59). Right-leg TH predicted the 0⁻5 and 0⁻10 m intervals (R² = 0.55⁻0.81); the VJ predicted the 0⁻30 m interval and RSA TT (R² = 0.41⁻0.84). Between-leg TH asymmetry correlated with and predicted left-leg 505 and RSA PD ( r = -0.68⁻0.62; R² = 0.39⁻0.46). Improvements in jumping ability could contribute to faster speed and RSA performance in collegiate soccer players.

Relationships and Predictive Capabilities of Jump Assessments to Soccer-Specific Field Test Performance in Division I Collegiate Players

Directory of Open Access Journals (Sweden)

Robert G. Lockie

2016-12-01

Full Text Available Leg power is an important characteristic for soccer, and jump tests can measure this capacity. Limited research has analyzed relationships between jumping and soccer-specific field test performance in collegiate male players. Nineteen Division I players completed tests of: leg power (vertical jump (VJ, standing broad jump (SBJ, left- and right-leg triple hop (TH; linear (30 m sprint; 0–5 m, 5–10 m, 0–10, 0–30 m intervals and change-of-direction (505 speed; soccer-specific fitness (Yo-Yo Intermittent Recovery Test Level 2; and 7 × 30-m sprints to measure repeated-sprint ability (RSA; total time (TT, performance decrement (PD. Pearson’s correlations (r determined jump and field test relationships; stepwise regression ascertained jump predictors of the tests (p < 0.05. All jumps correlated with the 0–5, 0–10, and 0–30 m sprint intervals (r = −0.65–−0.90. VJ, SBJ, and left- and right-leg TH correlated with RSA TT (r = −0.51–−0.59. Right-leg TH predicted the 0–5 and 0–10 m intervals (R2 = 0.55–0.81; the VJ predicted the 0–30 m interval and RSA TT (R2 = 0.41–0.84. Between-leg TH asymmetry correlated with and predicted left-leg 505 and RSA PD (r = −0.68–0.62; R2 = 0.39–0.46. Improvements in jumping ability could contribute to faster speed and RSA performance in collegiate soccer players.

Division of Analytical Chemistry, 1998

DEFF Research Database (Denmark)

Hansen, Elo Harald

1999-01-01

The article recounts the 1998 activities of the Division of Analytical Chemistry (DAC- formerly the Working Party on Analytical Chemistry, WPAC), which body is a division of the Federation of European Chemical Societies (FECS). Elo Harald Hansen is the Danish delegate, representing The Danish...... Chemical Society/The Society for Analytical Chemistry....

Oil spill sorbents: Testing protocol and certification listing program

International Nuclear Information System (INIS)

Cooper, D.; Gausemel, I.

1993-01-01

Environment Canada's Emergencies Engineering Division is spearheading a program in conjunction with the Canadian General Standards Board that would see the development of a certification and listing program in addition to a national standard for the testing of sorbent materials. Funding for this program is provided by Environment Canada (EC), Canadian Coast Guard (CCG), Marine Spill Response Corporation (MSRC), US Coast Guard (USCG), and US Minerals Management Service (MMS). The test methods are based upon those defined by the American Society for Testing and Materials and previous test methods developed by Environment Canada for our series of reports entitled Selection Criteria and Laboratory Evaluation of Oil Spill Sorbents. This series, which was started in 1975, encompasses a number of commercially available oil spill sorbents tested with different petroleum products and hydrocarbon solvents. The testing program will categorize the sorbents according to their operating characteristics. The main categories are oil spills on water, oil spills on land, and industrial use. The characteristics to be evaluated with the new test protocols include initial and maximum sorption capacities, water pickup, buoyancy, reuse potential, retention profile, disintegration (material integrity), and ease of application and retrieval. In the near future are plans to incorporate changes to the test that would involve increasing the list of test liquids to encompass spills in an industrial setting, in addition to testing sorbent booms and addressing the disposal problem

Current programmes of Metallurgy Division (1991)

International Nuclear Information System (INIS)

1991-01-01

Current research and development programmes of the Metallurgy Division are listed under the headings: 1)Thrust Areas, 2)High Temperature Materials Section, 3)Chemical Metallurgy Section, 4)Metallurgical Thermochemistry Section, 5)Physical Metallurgy Section, 6)Mechanical Metallurgy Section, 7)Corrosion Metallurgy Section, 8)Electrochemical Science and Technology Section, 9)Ceramics Section, and 10)Fabrication and Maintenance Group. A list of equipment in the Division and a list of sciientific personnel of the Division are also given. (M.G.B.)

Development and Testing of the Church Environment Audit Tool.

Science.gov (United States)

Kaczynski, Andrew T; Jake-Schoffman, Danielle E; Peters, Nathan A; Dunn, Caroline G; Wilcox, Sara; Forthofer, Melinda

2018-05-01

In this paper, we describe development and reliability testing of a novel tool to evaluate the physical environment of faith-based settings pertaining to opportunities for physical activity (PA) and healthy eating (HE). Tool development was a multistage process including a review of similar tools, stakeholder review, expert feedback, and pilot testing. Final tool sections included indoor opportunities for PA, outdoor opportunities for PA, food preparation equipment, kitchen type, food for purchase, beverages for purchase, and media. Two independent audits were completed at 54 churches. Interrater reliability (IRR) was determined with Kappa and percent agreement. Of 218 items, 102 were assessed for IRR and 116 could not be assessed because they were not present at enough churches. Percent agreement for all 102 items was over 80%. For 42 items, the sample was too homogeneous to assess Kappa. Forty-six of the remaining items had Kappas greater than 0.60 (25 items 0.80-1.00; 21 items 0.60-0.79), indicating substantial to almost perfect agreement. The tool proved reliable and efficient for assessing church environments and identifying potential intervention points. Future work can focus on applications within faith-based partnerships to understand how church environments influence diverse health outcomes.

When we test, do we stress? Impact of the testing environment on cortisol secretion and memory performance in older adults.

Science.gov (United States)

Sindi, Shireen; Fiocco, Alexandra J; Juster, Robert-Paul; Pruessner, Jens; Lupien, Sonia J

2013-08-01

The majority of studies find that older adults have worse memory performance than young adults. However, contextual features in the testing environment may be perceived as stressful by older adults, increasing their stress hormone levels. Given the evidence that older adults are highly sensitive to the effects of stress hormones (cortisol) on memory performance, it is postulated that a stressful testing environment in older adults can lead to an acute stress response and to memory impairments. The current study compared salivary cortisol levels and memory performance in young and older adults tested in environments manipulated to be stressful (unfavourable condition) or not stressful (favourable condition) for each age group. 28 young adults and 32 older adults were tested in two testing conditions: (1) a condition favouring young adults (constructed to be less stressful for young adults), and (2) a condition favouring older adults (constructed to be less stressful for older adults). The main outcome measure was salivary cortisol levels. Additionally, immediate and delayed memory performances were assessed during each condition. In older adults only, we found significantly high cortisol levels and low memory performance in the condition favouring young adults. In contrast, cortisol levels were lower and memory performance was better when older adults were tested in conditions favouring them. There was no effect of testing condition in young adults. The results demonstrate that older adults' memory performance is highly sensitive to the testing environment. These findings have important implications for both research and clinical settings in which older adults are tested for memory performance. Copyright © 2012 Elsevier Ltd. All rights reserved.

USB HW/SW Co-Simulation Environment with Custom Test Tool Integration

Directory of Open Access Journals (Sweden)

Grigor Y. Zargaryan

2014-06-01

Full Text Available This paper describes a new verification environment for USB 2.0 controller. New methodology is presented, where a co-simulation environment is used as one of the starting points for the embedded hardware/software development and as an accelerator of the overall design process. The verification environment is based on the device emulation/virtualization technique, using USB controller’s real register transfer level (RTL instead of models. This approach is functionally very close to the corresponding real-world devices and allows wider opportunities for hardware debugging. The new software utilities for USB host and device functionality testing are also presented. This tool allows generating custom tests by including various transfer types and modifying parameters such as data payload, interval, number of pipes, etc. It can be used for both hardware (HW and software (SW limitations characterization, as well as debugging.

Chemical and Laser Sciences Division annual report 1989

International Nuclear Information System (INIS)

Haines, N.

1990-06-01

The Chemical and Laser Sciences Division Annual Report includes articles describing representative research and development activities within the Division, as well as major programs to which the Division makes significant contributions

Performance testing of waste forms in a tuff environment

International Nuclear Information System (INIS)

Oversby, V.M.

1983-11-01

This paper describes experimental work conducted to establish the chemical composition of water which will have reacted with Topopah Spring Member tuff prior to contact with waste packages. The experimental program to determine the behavior of spent fuel and borosilicate glass in the presence of this water is then described. Preliminary results of experiments using spent fuel segments with defects in the Zircaloy cladding are presented. Some results from parametric testing of a borosilicate glass with tuff and 304L stainless steel are also discussed. Experiments conducted using Topopah Spring tuff and J-13 well water have been conducted to provide an estimate of the post-emplacement environment for waste packages in a repository at Yucca Mountain. The results show that emplacement of waste packages should cause only small changes in the water chemistry and rock mineralogy. The changes in environment should not have any detrimental effects on the performance of metal barriers or waste forms. The NNWSI waste form testing program has provided preliminary results related to the release rate of radionuclides from the waste package. Those results indicate that release rates from both spent fuel and borosilicate glass should be below 1 part in 10 5 per year. Future testing will be directed toward making release rate testing more closely relevant to site specific conditions. 17 references, 7 figures

Assessing The Representative And Discriminative Ability Of Test Environments For Rice Breeding In Malaysia Using GGE Biplot

Directory of Open Access Journals (Sweden)

Yusuff Oladosu

2017-11-01

Full Text Available Identification of outstanding rice genotype for target environments is complicated by genotype environment interactions. Using genotype main effect plus genotype by environment interaction GGE Biplot software fifteen rice genotypes were evaluated at five locations representing the major rice producing areas in peninsula Malaysia in two cropping seasons to i identify ideal test environment for selecting superior rice genotype and ii identify discriminative and representative ability of test locations. Genotypes locations years and genotypes by environment interaction effect revealed high significant difference P 0.01 for number of tillers per hill grains per panicle grain weight per hill and yield per hectare. Grain yield per hectare had a non-repeatable crossover pattern that formed a complex and single mega-environment. Based on the crossover pattern a set of cultivars were selected for the whole region on the merit of mean performance and their stability analysis. The tested environments were divided into two mega-environments. An ideal test environment that measures the discriminative and representative ability of test location reveal that environment Sekinchan SC is the best environment while Kedah KD and Penang PN can also be considered as favorable environment whereas Serdang SS and Tanjung Karang TK were the poorest locations for selecting genotypes adapted to the whole region. This study serves a reference for genotypes evaluation as well as identification of test locations for rice breeding in Malaysia.

Qualification test of packages for transporting radioactive materials and wastes

International Nuclear Information System (INIS)

Oliveira Santos, P. de; Miaw, S.T.W.

1990-01-01

Since 1979 the Waste Treatment Division of Nuclear Tecnology Development Center has been developed and tested packagings for transporting radioactive materials and wastes. The Division has designed facilities for testing Type A packages in accordance with the adopted regulations. The Division has tested several packages for universities, research centers, industries, INB, FURNAS, etc. (author) [pt

Division of Information Technology - Overview

International Nuclear Information System (INIS)

Szlachciak, J.

2007-01-01

I have a great pleasure to introduce the youngest division in our Institute, namely the Division of Information Technology. The division was created in 2005, but this is the first time when it reports its activities. The main purpose of creation was a better management of al IT activities in different departments, lowering IT costs and increase security over all computer systems used be the Institute. Although we have started with small human resources, we have received a big support from other departments. Special thanks go to the Department of Detectors and Nuclear Electronics. Our division handles many service-oriented activities. In daily work we answer many IT-related questions and deliver our help in order to solve hardware and software problems. The style of our work can be described as a result-oriented one. Here is the list of our biggest achievements: · construction of the server room; · implementation of two electronic bank systems; · development of the dynamic hardware and software inventory system; · development of the Scientific Activity Database. (author)

Sensor integration and testing in an airborne environment

Science.gov (United States)

Ricks, Timothy P.; Streling, Julie T.; Williams, Kirk W.

2005-11-01

The U.S. Army Redstone Technical Test Center (RTTC) has been supporting captive flight testing of missile sensors and seekers since the 1980's. Successful integration and test of sensors in an airborne environment requires attention to a broad range of disciplines. Data collection requirements drive instrumentation and flight profile configurations, which along with cost and airframe performance factors influence the choice of test aircraft. Installation methods used for instrumentation must take into consideration environmental and airworthiness factors. In addition, integration of test equipment into the aircraft will require an airworthiness release; procedures vary between the government for military aircraft, and the Federal Aviation Administration (FAA) for the use of private, commercial, or experimental aircraft. Sensor mounting methods will depend on the type of sensor being used, both for sensor performance and crew safety concerns. Pilots will require navigation input to permit the execution of accurate and repeatable flight profiles. Some tests may require profiles that are not supported by standard navigation displays, requiring the use of custom hardware/software. Test locations must also be considered in their effect on successful data collection. Restricted airspace may also be required, depending on sensor emissions and flight profiles.

Progress report of Environmental Assessment Division: 1995-1997

Energy Technology Data Exchange (ETDEWEB)

Nair, P V.N.; Nambi, K S.V. [comps.; Environmental Assessment Division, Bhabha Atomic Research Centre, Mumbai (India)

1998-08-01

The research and development (R and D) activities of Environmental Assessment Division during the period 1995 - 1997 are reported in the form of individual summaries arranged under the headings: 1) Studies on Radioactivity Measurements 2) Internal Dosimetry Studies 3) Epidemiological Studies 4) Aerosol Studies 5) Pollution Monitoring Systems 6) Studies on Trace Constituents in the Environment 7) Modelling Studies 8) Radiological Safety Assessment and 9) Dating Studies. At the end of the report, list of publications including papers published in journals, papers in symposium proceedings, papers in bulletins/newsletters and reports and summaries of Ph.D. theses completed during the period are given. (author)

The Rapid Integration and Test Environment - A Process for Achieving Software Test Acceptance

OpenAIRE

Jack, Rick

2010-01-01

Proceedings Paper (for Acquisition Research Program) Approved for public release; distribution unlimited. The Rapid Integration and Test Environment (RITE) initiative, implemented by the Program Executive Office, Command, Control, Communications, Computers and Intelligence, Command and Control Program Office (PMW-150), was born of necessity. Existing processes for requirements definition and management, as well as those for software development, did not consistently deliver high-qualit...

Heavy mineral sorting and distributions within massive sandstone divisions (Bouma A divisions) of Brushy Canyon Formation turbidites

Science.gov (United States)

Motanated, K.; Tice, M. M.

2009-12-01

KANNIPA MOTANATED and MICHAEL M. TICE Department of Geology and Geophysics, Texas A&M University, College Station, TX 77843-3115, USA Sediment sorting data are commonly used for interpreting depositional environments, analyzing mechanisms of deposition and transportation, and inferring relative transport distance of sediments. Typically, sorting in sandstones is estimated by point-counting thin sections which is a time consuming procedure and requires cutting sections of rock samples. We demonstrate a new technique for quantifying sediment sorting using element distribution maps obtained by x-ray fluorescence microscopy. We show that hydraulic sorting of Zr- and Ti- bearing grains (probably zircon and rutile, respectively) results in characteristic vertical profiles of Zr and Ti abundances within the Bouma A divisions of turbidites of the Brushy Canyon Formation, Delaware Basin, southern New Mexico. Zr- and Ti- bearing grains decrease in abundance and diameter from bases to tops of A divisions in every sample examined in this study. These results contrast with previous observations which suggest that grading in Brushy Canyon Formation structureless sandstones is absent or rare. The data support turbiditic interpretations of these rocks against traction current interpretations which rely on the lack of textural grading. Grading is reflected in vertical profiles of Ti/Al, Zr/Al and Zr/Ti ratios, which each decrease upward. These compositional variations could potentially be used as geochemical proxies for physical sorting, and might be useful for inferring depositional processes and relative transport distances.

An examination of the stretching practices of Division I and Division III college football programs in the midwestern United States.

Science.gov (United States)

Judge, Lawrence W; Craig, Bruce; Baudendistal, Steve; Bodey, Kimberly J

2009-07-01

Research supports the use of preactivity warm-up and stretching, and the purpose of this study was to determine whether college football programs follow these guidelines. Questionnaires designed to gather demographic, professional, and educational information, as well as specific pre- and postactivity practices, were distributed via e-mail to midwestern collegiate programs from NCAA Division I and III conferences. Twenty-three male coaches (12 from Division IA schools and 11 from Division III schools) participated in the study. Division I schools employed certified strength coaches (CSCS; 100%), whereas Division III schools used mainly strength coordinators (73%), with only 25% CSCS. All programs used preactivity warm-up, with the majority employing 2-5 minutes of sport-specific jogging/running drills. Pre stretching (5-10 minutes) was performed in 19 programs (91%), with 2 (9%) performing no pre stretching. Thirteen respondents used a combination of static/proprioceptive neuromuscular facilitation/ballistic and dynamic flexibility, 5 used only dynamic flexibility, and 1 used only static stretching. All 12 Division I coaches used stretching, whereas only 9 of the 11 Division III coaches did (p = 0.22). The results indicate that younger coaches did not use pre stretching (p = 0.30). The majority of the coaches indicated that they did use post stretching, with 11 of the 12 Division I coaches using stretching, whereas only 5 of the 11 Division III coaches used stretching postactivity (p = 0.027). Divisional results show that the majority of Division I coaches use static-style stretching (p = 0.049). The results of this study indicate that divisional status, age, and certification may influence how well research guidelines are followed. Further research is needed to delineate how these factors affect coaching decisions.

The Global Environment as Life-worlds: On the Meanings of Sustainable Development

Directory of Open Access Journals (Sweden)

Kei Otsuki

2009-01-01

Full Text Available The environmental political arena was once dominated by two opposing forces. On the one hand, environmentalists demanded unconditional conservation of the environment; and on the other, developmentalistspromoted economic development by exploiting the environment. The normalization of the concept of sustainable development at the end of the 1980s opened a new policy space in this arena, in which expertpolicy-makers began to emphasize the importance of natural resource management. Yet, this emphasis on management has not sufficiently taken account of social and cultural meanings attached to the environment, generating policy contestations furthermore. This article argues that the current contestations stem from the persisting assumption that the environment as a set of natural resources to be managed is detachable from human activities. Two examples illustrate this argument: the first example shows the emergence of social development concerns in the Amazon; and the second example shows intensifying cultural politics of whaling. Both instances demonstrate that the assumption of the environment at stake (rainforest and whale to be managed relies on a clear conceptual division between nature and society concerning the environment, whereas this division has been continuously blurred in the process of political negotiations over time. Drawing on the phenomenology and some aspects of science studies, this article proposes to discard the nature-society division and consider the environment as a re-assemblage of human and non-human elements embedded within the involved actors’ life-worlds.

Energy Technology Division research summary 2004

International Nuclear Information System (INIS)

Poeppel, R. B.; Shack, W. J.

2004-01-01

The Energy Technology (ET) Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy (DOE). The Division's capabilities are generally applied to technical issues associated with energy systems, biomedical engineering, transportation, and homeland security. Research related to the operational safety of commercial light water nuclear reactors (LWRs) for the US Nuclear Regulatory Commission (NRC) remains another significant area of interest for the Division. The pie chart below summarizes the ET sources of funding for FY 2004

1998 Chemical Technology Division Annual Technical Report.

Energy Technology Data Exchange (ETDEWEB)

Ackerman, J.P.; Einziger, R.E.; Gay, E.C.; Green, D.W.; Miller, J.F.

1999-08-06

The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division's activities during 1998 are presented.

Chemical Technology Division annual technical report 1997

International Nuclear Information System (INIS)

1998-06-01

The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials and electrified interfaces. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division's activities during 1997 are presented

Biology Division progress report for the period of October 1, 1986--September 30, 1988

Energy Technology Data Exchange (ETDEWEB)

1988-09-01

The Biology Division of the Oak Ridge National Laboratory is one component of the Department of Energy's intramural program in life sciences. Accordingly, /approximately/75% of the Division's total budget is derived from the Department of Energy through its Office of Health and Environmental Research. With respect to experimental biology, the congressionally mandated mission of this Office is to study adverse health effects of energy production and utilization. Within this stated broad mission, common themes among the research programs of the Biology Division are interactions of animals, cells, and molecules with their respective environments. Investigations focus on genetic and somatic effects of radiation and chemicals. Goals include identification and quantification of these effects, elucidation of pathways by which the effects are expressed, assessment of risks associated with radiation and chemical exposures, and establishment of strategies for extrapolation of risk data from animals to humans. Concurrent basic studies in genetics, biochemistry, molecular biology, and cell biology illuminate normal life processes as prerequisites to comprehending mutagenic and carcinogenic effects of environmental agents.

Energy Division progress report, fiscal years 1994--1995

Energy Technology Data Exchange (ETDEWEB)

Moser, C.I. [ed.

1996-06-01

At ORNL, the Energy Division`s mission is to provide innovative solutions to energy and related issues of national and global importance through interdisciplinary research and development. Its goals and accomplishments are described in this progress report for FY 1994 and FY 1995. The Division`s expenditures in FY 1995 totaled 44.9 million. Sixty percent of the divisions work was supported by the US DOE. Other significant sponsors include the US DOT, the US DOD, other federal agencies, and some private organizations. The Division`s programmatic activities cover three main areas: (1) analysis and assessment, (2) transportation systems, and (3) energy use and delivery technologies. Analysis and assessment activities involve energy and resource analysis, preparation of environmental assessments and impact statements, and impact statements, research on emergency preparedness, analysis of energy and environmental needs in developing countries, and transportation analysis. Transportation systems research seeks to improve the quality of both civilian and military transportation efforts. Energy use and delivery technologies focus on building equipment, building envelopes, (walls, roofs, attics, and materials), improvement of energy efficiency in buildings, and electric power systems.

Digital Arithmetic: Division Algorithms

DEFF Research Database (Denmark)

Montuschi, Paolo; Nannarelli, Alberto

2017-01-01

Division is one of the basic arithmetic operations supported by every computer system. The operation can be performed and implemented by either hardware or software, or by a combination of the two. Although division is not as frequent as addition and multiplication, nowadays, most processors impl...... significant hardware resources and is more suitable for software implementation on the existing multiply units. The purpose of this entry is to provide an introductory survey using a presentation style suitable for the interested non-specialist readers as well....

Power Dissipation in Division

DEFF Research Database (Denmark)

Liu, Wei; Nannarelli, Alberto

2008-01-01

A few classes of algorithms to implement division in hardware have been used over the years: division by digit-recurrence, by reciprocal approximation by iterative methods and by polynomial approximation. Due to the differences in the algorithms, a comparison among their implementation in terms o...... of performance and precision is sometimes hard to make. In this work, we use power dissipation and energy consumption as metrics to compare among those different classes of algorithms. There are no previous works in the literature presenting such a comparison....

Interoperable Solution for Test Execution in Various I&T Environments

Science.gov (United States)

Lee, Young H.; Bareh, Magdy S.

2006-01-01

When there is spacecraft collaboration between several industry partners, there is an inherent difference in integration and test (I&T) methodologies, which creates a challenge for verifying flight systems during the development phase. To converge the differing I&T methodologies, considerations were required for multiple project areas such as Flight System Testbed (FST), Assembly, Test, and Launch Operations (ATLO), and Spacecraft Simulator environments. This paper details the challenges and approaches of the JPL's effort in engineering a solution to testing the flight system with the Mission Operations Ground System while maintaining the comparability with testing methods of the industry partners.

Biological effect of aerospace environment on alfalfa

International Nuclear Information System (INIS)

Zhang Yuexue; Liu Jielin; Han Weibo; Tang Fenglan; Hao Ruochao; Shang Chen; DuYouying; Li Jikai; Wang Changshan

2009-01-01

The biological effect of aerospace environment on two varieties of Medicago sativa L. was studied. In M 1 germination results showed that aerospace environment increased cell division and the number of micronucleus, changed germination rate, caused seedling aberrations. Cytogenetical and seedling aberration of Zhaodong showed more sensitivity than Longmu 803. Branches and fresh weight of Zhaodong had shown more serious damage than control and Longmu 803. (authors)

Important projects of the Division

International Nuclear Information System (INIS)

2008-01-01

In this chapter important projects of the Division for Radiation Safety, NPP Decommissioning and Radwaste Management of the VUJE, a. s. are presented. Division for Radiation Safety, NPP Decommissioning and Radwaste Management has successfully carried out variety of significant projects. The most significant projects that were realised, are implemented and possible future projects are introduced in the following part of presentation.

Cell division requirement for activation of murine leukemia virus in cell culture by irradiation

International Nuclear Information System (INIS)

Otten, J.A.; Quarles, J.M.; Tennant, R.W.

1976-01-01

Actively dividing cultures of AKR mouse cells were exposed to relatively low dose-rates of γ radiation and tested for activation of endogenous leukemia viruses. Efficient and reproducible induction of virus was obtained with actively dividing cells, but cultures deprived of serum to inhibit cell division before and during γ irradiation were not activated, even when medium with serum was added immediately after irradiation. These results show that cell division was required for virus induction but that a stable intermediate similar to the state induced by halogenated pyrimidines was not formed. In actively dividing AKR cell cultures, virus activation appeared to be proportional to the dose of γ radiation; the estimated frequency of activation was 1-8 x 10 - 5 per exposed cell and the efficiency of activation was approximately 0.012 inductions per cell per rad. Other normal primary and established mouse cell cultures tested were not activated by γ radiation. The requirement of cell division for radiation and chemical activation may reflect some common mechanism for initiation of virus expression

14 CFR Appendix J to Part 23 - HIRF Environments and Equipment HIRF Test Levels

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false HIRF Environments and Equipment HIRF Test Levels J Appendix J to Part 23 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF.... 23, App. J Appendix J to Part 23—HIRF Environments and Equipment HIRF Test Levels This appendix...

Chemical Technology Division. Annual technical report, 1995

International Nuclear Information System (INIS)

Laidler, J.J.; Myles, K.M.; Green, D.W.; McPheeters, C.C.

1996-06-01

Highlights of the Chemical Technology (CMT) Division's activities during 1995 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) methods for treatment of hazardous waste and mixed hazardous/radioactive waste; (3) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (4) processes for separating and recovering selected elements from waste streams, concentrating low-level radioactive waste streams with advanced evaporator technology, and producing 99 Mo from low-enriched uranium; (5) electrometallurgical treatment of different types of spent nuclear fuel in storage at Department of Energy sites; and (6) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems

Instrumentation and Controls Division Progress report, July 1, 1992--June 30, 1994

Energy Technology Data Exchange (ETDEWEB)

McDonald, D.W.

1995-06-01

The Instrumentation and Controls (I&C) Division serves a national laboratory, and as such has an expansive domain: science, industry, and national defense. The core mission is to support the scientific apparatus of the Laboratory and all of the systems that protect the safety and health of people and the environment. Progress is reported for the five sections: photonics and measurements systems, electronic systems, signal processing, controls and systems integration, and technical support.

Perceptions about gender relations and sexual division of labor for people with disabilities

Directory of Open Access Journals (Sweden)

Lilian Barros Moreira

2011-07-01

Full Text Available Contemporary society has discussed the idea of “diversity”, and among its possibilities, the insertion of people with disabilities (PWDs in organizations has been often discussed in organizational studies. Although disability appears to be no longer an uncomfortable subject to be discussed, it is still a very delicate issue to be talked about. In addition to it, gender relations and sexual division of   labor are not solved issues when work is involved. This work was carried out with the objective of understanding the perceptions of PWDs about gender relations and sexual division of  labor. We argue that both this perception and its origin are connected to the subjectivity. The research was conducted in a hospital, where five people were interviewed. The interviews were analyzed through the method of content analysis. They did not show explicitly the interviewees’ perception of unequal gender relations, but this was noticed through the method of observation. The interviewees’ view of gender relations was found to be full of social stereotypes. Finally, questions were asked that intended to lead the reader to a deeper reflection about sexual division of labor, disability and prejudice in the organizational environment.

Biology Division progress report for period of October 1, 1988--September 30, 1989

Energy Technology Data Exchange (ETDEWEB)

1990-02-01

The Biology Division of the Oak Ridge National Laboratory is one component of the Department of Energy's intramural program in life sciences. With respect to experimental biology, the congressionally mandated mission of this Office is to study adverse health effects of energy production and utilization. Within this stated broad mission, common themes among the research programs of the Biology Division are interactions of animals, cells, and molecules with their respective environments. Investigations focus on genetic and somatic effects of radiation and chemicals. Goals include identification and quantification of these effects, elucidation of pathways by which the effects are expressed, assessment of risks associated with radiation and chemical exposures, and establishment of strategies for extrapolation of risk data from animals to humans. Concurrent basic studies in genetics, biochemistry, molecular biology, and cell biology illuminate normal life processes as prerequisites to comprehending mutagenic and carcinogenic effects of environmental agents. This Progress Report is intended to provide both broad perspectives of the Division's research programs and synopses of recent achievements. Readers are invited to contact individual principal investigators for more detailed information, including reprints of publications. 120 refs.

Spatial Layout of Multi-Environment Test Sites: A Case Study of Maize in Jilin Province

Directory of Open Access Journals (Sweden)

Zuliang Zhao

2018-05-01

Full Text Available Variety regional tests based on multiple environments play a critical role in understanding the high yield and adaptability of new crop varieties. However, the current approach mainly depends on experience from breeding experts and is difficulty to promote because of inconsistency between testing and actual situation. We propose a spatial layout method based on the existing systematic regional test network. First, the method of spatial clustering was used to cluster the planting environment. Then, we used spatial stratified sampling to determine the minimum number of test sites in each type of environment. Finally, combined with the factors such as the convenience of transportation and the planting area, we used spatial balance sampling to generate the layout of multi-environment test sites. We present a case study for maize in Jilin Province and show the utility of the method with an accuracy of about 94.5%. The experimental results showed that 66.7% of sites are located in the same county and the unbalanced layout of original sites is improved. Furthermore, we conclude that the set of operational technical ideas for carrying out the layout of multi-environment test sites based on crop varieties in this paper can be applied to future research.

Stationary infinitely divisible processes

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole E.

Several recent strands of work has led to the consideration of various types of continuous time stationary and infinitely divisible processes. A review of these types, with some new results, is presented.......Several recent strands of work has led to the consideration of various types of continuous time stationary and infinitely divisible processes. A review of these types, with some new results, is presented....

FtsZ-less prokaryotic cell division as well as FtsZ- and dynamin-less chloroplast and non-photosynthetic plastid division

Directory of Open Access Journals (Sweden)

Shin-Ya eMiyagishima

2014-09-01

Full Text Available The chloroplast division machinery is a mixture of a stromal FtsZ-based complex descended from a cyanobacterial ancestor of chloroplasts and a cytosolic dynamin-related protein (DRP 5B-based complex derived from the eukaryotic host. Molecular genetic studies have shown that each component of the division machinery is normally essential for normal chloroplast division. However, several exceptions have been found. In the absence of the FtsZ ring, nonphotosynthetic plastids are able to proliferate, likely by elongation and budding. Depletion of DRP5B impairs, but does not stop chloroplast division. Chloroplasts in glaucophytes, which possesses a peptidoglycan (PG layer, divide without DRP5B. Certain parasitic eukaryotes possess nonphotosynthetic plastids of secondary endosymbiotic origin, but neither FtsZ nor DRP5B is encoded in their genomes. Elucidation of the FtsZ- and/or DRP5B-less chloroplast division mechanism will lead to a better understanding of the function and evolution of the chloroplast division machinery and the finding of the as-yet-unknown mechanism that is likely involved in chloroplast division. Recent studies have shown that FtsZ was lost from a variety of prokaryotes, many of which lost PG by regressive evolution. In addition, even some of the FtsZ-bearing bacteria are able to divide when FtsZ and PG are depleted experimentally. In some cases, alternative mechanisms for cell division, such as budding by an increase of the cell surface-to-volume ratio, are proposed. Although PG is believed to have been lost from chloroplasts other than in glaucophytes, there is some indirect evidence for the existence of PG in chloroplasts. Such information is also useful for understanding how nonphotosynthetic plastids are able to divide in FtsZ-depleted cells and the reason for the retention of FtsZ in chloroplast division. Here we summarize information to facilitate analyses of FtsZ- and/or DRP5B-less chloroplast and nonphotosynthetic plastid

Nuclear Technology Division annual progress report for period ending June 30, 1974

International Nuclear Information System (INIS)

1975-01-01

Abstracts of research projects are presented concerning nuclear properties, general reactor development and support, test reactor operations support, LOFT support, PBF support, FEFPL support, TRSP support, techniques and instrumentation, non-nuclear energy sources, and related activities of division personnel. (U.S.)

Earth Sciences Division collected abstracts: 1979

International Nuclear Information System (INIS)

Henry, A.L.; Schwartz, L.L.

1980-01-01

This report is a compilation of abstracts of papers, internal reports, and talks presented during 1979 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore Laboratory. The arrangement is alphabetical (by author). For a given report, a bibliographic reference appears under the name of each coauthor, but the abstract iself is given only under the name of the first author or the first Earth Sciences Division author. A topical index at the end of the report provides useful cross references, while indicating major areas of research interest in the Earth Sciences Division

Chemical Sciences Division annual report 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

The division is one of ten LBL research divisions. It is composed of individual research groups organized into 5 scientific areas: chemical physics, inorganic/organometallic chemistry, actinide chemistry, atomic physics, and chemical engineering. Studies include structure and reactivity of critical reaction intermediates, transients and dynamics of elementary chemical reactions, and heterogeneous and homogeneous catalysis. Work for others included studies of superconducting properties of high-{Tc} oxides. In FY 1994, the division neared completion of two end-stations and a beamline for the Advanced Light Source, which will be used for combustion and other studies. This document presents summaries of the studies.

Accelerator and Fusion Research Division annual report, October 1981-September 1982. Fiscal year 1982

International Nuclear Information System (INIS)

Johnson, R.K.; Bouret, C.

1983-05-01

This report covers the activities of LBL's Accelerator and Fusion Research Division (AFRD) during 1982. In nuclear physics, the Uranium Beams Improvement Project was concluded early in the year, and experimentation to exploit the new capabilities began in earnest. Technical improvement of the Bevalac during the year centered on a heavy-ion radiofrequency quadrupole (RFQ) as part of the local injector upgrade, and we collaborated in studies of high-energy heavy-ion collision facilities. The Division continued its collaboration with Fermilab to design a beam-cooling system for the Tevatron I proton-antiprotron collider and to engineer the needed cooling components for the antiproton. The high-field magnet program set yet another record for field strength in an accelerator-type dipole magnet (9.2 T at 1.8 K). The Division developed the design for the Advanced Light Source (ALS), a 1.3-GeV electron storage ring designed explicitly (with low beam emittance and 12 long straight sections) to generate high-brilliance synchrotron light from insertion devices. The Division's Magnetic Fusion Energy group continued to support major experiments at the Princeton Plasma Physics Laboratory, the Lawrence Livermore National Laboratory (LLNL), and General Atomic Co. by developing positive-ion-based neutral-beam injectors. Progress was made toward converting our major source-test facility into a long-pulse national facility, the Neutral Beam Engineering Test Facility, which was completed on schedule and within budget in 1983. Heavy Ion Fusion research focused on planning, theoretical studies, and beam-transport experiments leading toward a High Temperature Experiment - a major test of this promising backup approach to fusion energy

Physics Division progress report for period ending September 30, 1988

Energy Technology Data Exchange (ETDEWEB)

Livingston, A.B. (ed.)

1989-03-01

This report covers the research and development activities of the Physics Division for the 1988 fiscal year, beginning October 1, 1987, and ending September 30, 1988. The activities of this Division are concentrated in the areas of experimental nuclear physics, experimental atomic physics, and theoretical nuclear and atomic physics. Operation of the Holifield Heavy Ion Research Facility as a national user facility continues to represent the single largest activity within the Division. This year saw the completion of the acceleration tube upgrade of the 25-MV tandem electrostatic accelerator and the achievement of record terminal potentials, operation for an experiment with 25 million volts on terminal, and successful tests with beam at 25.5 MV. The experimental nuclear physics program continues to be dominated by research utilizing heavy ions. These activities, while continuing to center largely on the Holifield Facility, have seen significant growth in the use of facilities that provide intermediate energies and especially ultrarelativistic beams. The UNISOR program, since its inception, has been intimately associated with the Division and, most particularly, with the Holifield Facility. In addition to the Holifield Facility, the Division operates two smaller facilities, the EN Tandem and the ECR Ion Source Facility, as ''User Resources.'' The efforts in theoretical physics, covering both nuclear and atomic physics, are presented. In addition to research with multicharged heavy ions from the ECR source, the effort on atomic physics in support of the controlled fusion program includes a plasma diagnostics development program. The concentration of this program on optical and laser technology is marked by the change in designation to the Laser and Electro-Optics Lab. A small, continuing effort in elementary particle physics, carried out in collaboration with the University of Tennessee, is reported.

Physics Division progress report for period ending September 30, 1988

International Nuclear Information System (INIS)

Livingston, A.B.

1989-03-01

This report covers the research and development activities of the Physics Division for the 1988 fiscal year, beginning October 1, 1987, and ending September 30, 1988. The activities of this Division are concentrated in the areas of experimental nuclear physics, experimental atomic physics, and theoretical nuclear and atomic physics. Operation of the Holifield Heavy Ion Research Facility as a national user facility continues to represent the single largest activity within the Division. This year saw the completion of the acceleration tube upgrade of the 25-MV tandem electrostatic accelerator and the achievement of record terminal potentials, operation for an experiment with 25 million volts on terminal, and successful tests with beam at 25.5 MV. The experimental nuclear physics program continues to be dominated by research utilizing heavy ions. These activities, while continuing to center largely on the Holifield Facility, have seen significant growth in the use of facilities that provide intermediate energies and especially ultrarelativistic beams. The UNISOR program, since its inception, has been intimately associated with the Division and, most particularly, with the Holifield Facility. In addition to the Holifield Facility, the Division operates two smaller facilities, the EN Tandem and the ECR Ion Source Facility, as ''User Resources.'' The efforts in theoretical physics, covering both nuclear and atomic physics, are presented. In addition to research with multicharged heavy ions from the ECR source, the effort on atomic physics in support of the controlled fusion program includes a plasma diagnostics development program. The concentration of this program on optical and laser technology is marked by the change in designation to the Laser and Electro-Optics Lab. A small, continuing effort in elementary particle physics, carried out in collaboration with the University of Tennessee, is reported

Advances in nickel hydrogen technology at Yardney Battery Division

Science.gov (United States)

Bentley, J. G.; Hall, A. M.

1987-01-01

The current major activites in nickel hydrogen technology being addressed at Yardney Battery Division are outlined. Five basic topics are covered: an update on life cycle testing of ManTech 50 AH NiH2 cells in the LEO regime; an overview of the Air Force/industry briefing; nickel electrode process upgrading; 4.5 inch cell development; and bipolar NiH2 battery development.

Physics division annual report - October 2000.

Energy Technology Data Exchange (ETDEWEB)

Thayer, K. [ed.

2000-10-16

This report summarizes the research performed in the past year in the Argonne Physics Division. The Division's programs include operation of ATLAS as a national heavy-ion user facility, nuclear structure and reaction research with beams of heavy ions, accelerator research and development especially in superconducting radio frequency technology, nuclear theory and medium energy nuclear physics. The Division took significant strides forward in its science and its initiatives for the future in the past year. Major progress was made in developing the concept and the technology for the future advanced facility of beams of short-lived nuclei, the Rare Isotope Accelerator. The scientific program capitalized on important instrumentation initiatives with key advances in nuclear science. In 1999, the nuclear science community adopted the Argonne concept for a multi-beam superconducting linear accelerator driver as the design of choice for the next major facility in the field a Rare Isotope Accelerator (RIA) as recommended by the Nuclear Science Advisory Committee's 1996 Long Range Plan. Argonne has made significant R&D progress on almost all aspects of the design concept including the fast gas catcher (to allow fast fragmentation beams to be stopped and reaccelerated) that in large part, defined the RIA concept the superconducting rf technology for the driver accelerator, the multiple-charge-state concept (to permit the facility to meet the design intensity goals with existing ion-source technology), and designs and tests of high-power target concepts to effectively deal with the full beam power of the driver linac. An NSAC subcommittee recommended the Argonne concept and set as tie design goal Uranium beams of 100-kwatt power at 400 MeV/u. Argonne demonstrated that this goal can be met with an innovative, but technically in-hand, design.

Generating realistic environments for cyber operations development, testing, and training

Science.gov (United States)

Berk, Vincent H.; Gregorio-de Souza, Ian; Murphy, John P.

2012-06-01

Training eective cyber operatives requires realistic network environments that incorporate the structural and social complexities representative of the real world. Network trac generators facilitate repeatable experiments for the development, training and testing of cyber operations. However, current network trac generators, ranging from simple load testers to complex frameworks, fail to capture the realism inherent in actual environments. In order to improve the realism of network trac generated by these systems, it is necessary to quantitatively measure the level of realism in generated trac with respect to the environment being mimicked. We categorize realism measures into statistical, content, and behavioral measurements, and propose various metrics that can be applied at each level to indicate how eectively the generated trac mimics the real world.

Fusion Energy Division: Annual progress report, period ending December 31, 1987

Energy Technology Data Exchange (ETDEWEB)

Morgan, O.B. Jr.; Berry, L.A.; Sheffield, J.

1988-11-01

The Fusion Program of Oak Ridge National Laboratory (ORNL), a major part of the national fusion program, carries out research in nearly all areas of magnetic fusion. Collaboration among staff from ORNL, Martin Marietta Energy Systems, Inc., private industry, the academic community, and other fusion laboratories, in the United States and abroad, is directed toward the development of fusion as an energy source. This report documents the program's achievements during 1987. Issued as the annual progress report of the ORNL Fusion Energy Division, it also contains information from components of the Fusion Program that are external to the division (about 15% of the program effort). The areas addressed by the Fusion Program include the following: experimental and theoretical research on magnetic confinement concepts, engineering and physics of existing and planned devices, development and testing of diagnostic tools and techniques in support of experiments, assembly and distribution to the fusion community of databases on atomic physics and radiation effects, development and testing of technologies for heating and fueling fusion plasmas, development and testing of superconducting magnets for containing fusion plasmas, and development and testing of materials for fusion devices. Highlights from program activities are included in this report. 126 figs., 15 tabs.

Fusion Energy Division: Annual progress report, period ending December 31, 1987

International Nuclear Information System (INIS)

Morgan, O.B. Jr.; Berry, L.A.; Sheffield, J.

1988-11-01

The Fusion Program of Oak Ridge National Laboratory (ORNL), a major part of the national fusion program, carries out research in nearly all areas of magnetic fusion. Collaboration among staff from ORNL, Martin Marietta Energy Systems, Inc., private industry, the academic community, and other fusion laboratories, in the United States and abroad, is directed toward the development of fusion as an energy source. This report documents the program's achievements during 1987. Issued as the annual progress report of the ORNL Fusion Energy Division, it also contains information from components of the Fusion Program that are external to the division (about 15% of the program effort). The areas addressed by the Fusion Program include the following: experimental and theoretical research on magnetic confinement concepts, engineering and physics of existing and planned devices, development and testing of diagnostic tools and techniques in support of experiments, assembly and distribution to the fusion community of databases on atomic physics and radiation effects, development and testing of technologies for heating and fueling fusion plasmas, development and testing of superconducting magnets for containing fusion plasmas, and development and testing of materials for fusion devices. Highlights from program activities are included in this report. 126 figs., 15 tabs

Physics Research Integrated Development Environment (PRIDE)

International Nuclear Information System (INIS)

Burton, J.; Cormell, L.

1993-12-01

Past efforts to implement a Software Engineering approach to High Energy Physics computing have been met with significant resistance and have been, in many cases, only marginally successful. At least a portion of the problem has been the Lick of an integrated development environment, tailored to High Energy Physics and incorporating a suite of Computer Aided Software Engineering tools. The Superconducting Super Collider Physics Research Division Computing Department is implementing pilot projects to develop just such an environment

Theoretical Division annual report, FY 1975

International Nuclear Information System (INIS)

Carruthers, P.A.

1976-02-01

This report presents an overview of the activities in the Theoretical Division and a summary of research highlights during FY 1975. It is intended to inform a wide audience about the theoretical work of the LASL and, therefore, contains introductory material which places recent advances in a broader context. The report is organized into two special interest reports: reactor safety research and the Advanced Research Committee, and 11 reports from the T-Division group leaders on the work of their respective groups. Main interests and responsibilities are outlined including the relationship of the group's work to the work of other T-Division groups and other divisions at the Laboratory. The description of research highlights for FY 1975 explains in a fairly simple, straightforward manner the major recent advances and their significance. Each group report is followed by a publication list for FY 1975 (330 references) and a list of talks given outside the Laboratory (140 references). 29 figures

The History of Metals and Ceramics Division

Energy Technology Data Exchange (ETDEWEB)

Craig, D.F.

1999-01-01

The division was formed in 1946 at the suggestion of Dr. Eugene P. Wigner to attack the problem of the distortion of graphite in the early reactors due to exposure to reactor neutrons, and the consequent radiation damage. It was called the Metallurgy Division and assembled the metallurgical and solid state physics activities of the time which were not directly related to nuclear weapons production. William A. Johnson, a Westinghouse employee, was named Division Director in 1946. In 1949 he was replaced by John H Frye Jr. when the Division consisted of 45 people. He was director during most of what is called the Reactor Project Years until 1973 and his retirement. During this period the Division evolved into three organizational areas: basic research, applied research in nuclear reactor materials, and reactor programs directly related to a specific reactor(s) being designed or built. The Division (Metals and Ceramics) consisted of 204 staff members in 1973 when James R. Weir, Jr., became Director. This was the period of the oil embargo, the formation of the Energy Research and Development Administration (ERDA) by combining the Atomic Energy Commission (AEC) with the Office of Coal Research, and subsequent formation of the Department of Energy (DOE). The diversification process continued when James O. Stiegler became Director in 1984, partially as a result of the pressure of legislation encouraging the national laboratories to work with U.S. industries on their problems. During that time the Division staff grew from 265 to 330. Douglas F. Craig became Director in 1992.

The division of labor across the transition to parenthood : A justice perspective

NARCIS (Netherlands)

Kluwer, E.S; Heesink, J.A.M.; Van de Vliert, E.

2002-01-01

In a three-wave longitudinal survey among 293 couples, we studied the determinants of husbands' and wives' fairness judgments regarding the division of labor across the transition to parenthood. We tested predictions derived from the distributive justice framework that perceptions of fairness

An Evaluation of the Model School Division (MSD) Preschool Program for the School Year 1973-74.

Science.gov (United States)

District of Columbia Public Schools, Washington, DC. Dept. of Research and Evaluation.

This study was designed to assess the extent to which children served by the Model Schools Division Preschool Program developed socially, intellectually, physically and emotionally during the 1973-74 school year. This evaluation was also designed to measure the appropriateness of the learning environment and the amount of services provided by the…

Theoretical physics division

International Nuclear Information System (INIS)

Anon.

1980-01-01

Research activities of the theoretical physics division for 1979 are described. Short summaries are given of specific research work in the following fields: nuclear structure, nuclear reactions, intermediate energy physics, elementary particles [fr

Selling money on eBay: A field study of surplus division

OpenAIRE

Gizatulina, Alia; Gorelkina, Olga

2016-01-01

We study the division of trade surplus in a competitive market environment by conducting a natural field experiment on German eBay. Acting as a seller, we offer Amazon gift cards with face values of up to 500 Euro. Randomly arriving buyers, the subjects of our experiment, make price offers according to eBay rules. Using a novel decomposition method, we infer offered shares of trade surplus and find that the average share proposed to the seller amounts to 29%. Additionally, we document: (i) in...

Atmospheric and Geophysical Sciences Division: Program report, FY 1987

International Nuclear Information System (INIS)

1988-05-01

In 1988 the Atmospheric and Geophysical Sciences Division began its 15th year as a division. As the Division has grown over the years, its modeling capabilities have expanded to include a broad range of time and space scales ranging from hours to years, and from kilometers to global, respectively. For this report, we have chosen to show a subset of results from several projects to illustrate the breadth, depth, and diversity of the modeling activities that are a major part of the Division's research, development, and application efforts. In addition, the recent reorganization of the Division, including the merger of another group with the Division, is described, and the budget, personnel, models, and publications are reviewed. 95 refs., 26 figs., 2 tabs

DEVELOPMENT OF KITSAT-1 AND 2 MECHANICAL SYSTEM AND RESULTS OF ENVIRONMENT TEST

Directory of Open Access Journals (Sweden)

J. S. Bae

1996-06-01

Full Text Available The satellite experiences the launch environment such as vibration, acceleration, shock induced by rocket and the orbit environment such as high vacuum, no gravity, high temperature and cryogenic. Therefore, the satellite should be designed and manufactured to endure such environments. Also, special care must be taken on the assembly of parts and subsystem. Finally, we describe the environment test of microsatellite to ensure the reliable operation during launch period as well as in-orbit operation.

Couples’ Attitudes, Childbirth, and the Division of Labor

NARCIS (Netherlands)

Jansen, Miranda; Liefbroer, Aart C.

2006-01-01

In this article, the authors examine effects of partners’ attitudes on the timing of the birth of a first child, the division of domestic labor, the division of child care, and the division of paid labor of couples. They use data from the Panel Study of Social Integration in the Netherlands, which

Crash testing of nuclear fuel shipping containers

International Nuclear Information System (INIS)

Jefferson, R.M.; Yoshimura, H.R.

1977-08-01

In an attempt to understand the dynamics of extra severe transportation accidents and to evaluate state-of-the-art computational techniques for predicting the dynamic response of shipping casks involved in vehicular system crashes, the Environmental Control Technology Division of ERDA undertook a program with Sandia to investigate these areas. The program encompasses the following distinct major efforts. The first of these utilizes computational methods for predicting the effects of the accident environment and, subsequently, to calculate the damage incurred by a container as the result of such an accident. The second phase involves the testing of 1 / 8 -scale models of transportation systems. Through the use of instrumentation and high-speed motion photography the accident environments and physical damage mechanisms are studied in detail. After correlating the results of these first two phases, a full scale event involving representative hardware is conducted. To date two of the three selected test scenarios have been completed. Results of the program to this point indicate that both computational techniques and scale modeling are viable engineering approaches to studying accident environments and physical damage to shipping casks

Crash testing of nuclear fuel shipping containers

International Nuclear Information System (INIS)

Jefferson, R.M.; Yoshimura, H.R.

1977-12-01

In an attempt to understand the dynamics of extra severe transportation accidents and to evaluate state-of-the-art computational techniques for predicting the dynamic response of shipping casks involved in vehicular system crashes, the Environmental Control Technology Division of ERDA undertook a program with Sandia to investigate these areas. This program, which began in 1975, encompasses the following distinct major efforts. The first of these utilizes computational methods for predicting the effects of the accident environment and, subsequently, to calculate the damage incurred by a container as the result of such an accident. The second phase involves the testing of 1 / 8 -scale models of transportation systems. Through the use of instrumentation and high-speed motion photography, the accident environments and physical damage mechanisms are studied in detail. After correlating the results of these first two phases, a full scale event involving representative hardware is conducted. To date two of the three selected test scenarios have been completed. Results of the program to this point indicate that both computational techniques and scale modeling are viable engineering approaches to studying accident environments and physical damage to shipping casks

Radioactive Waste and Clean-up Division

International Nuclear Information System (INIS)

Collard, G.

2001-01-01

The main objectives of the Radioactive Waste and Clean-up division of SCK-CEN are outlined. The division's programme consists of research, development and demonstration projects and aims to contribute to the objectives of Agenda 21 on sustainable development in the field of radioactive waste and rehabilitation of radioactively contaminated sites

Stochastic Individual-Based Modeling of Bacterial Growth and Division Using Flow Cytometry

Directory of Open Access Journals (Sweden)

Míriam R. García

2018-01-01

Full Text Available A realistic description of the variability in bacterial growth and division is critical to produce reliable predictions of safety risks along the food chain. Individual-based modeling of bacteria provides the theoretical framework to deal with this variability, but it requires information about the individual behavior of bacteria inside populations. In this work, we overcome this problem by estimating the individual behavior of bacteria from population statistics obtained with flow cytometry. For this objective, a stochastic individual-based modeling framework is defined based on standard assumptions during division and exponential growth. The unknown single-cell parameters required for running the individual-based modeling simulations, such as cell size growth rate, are estimated from the flow cytometry data. Instead of using directly the individual-based model, we make use of a modified Fokker-Plank equation. This only equation simulates the population statistics in function of the unknown single-cell parameters. We test the validity of the approach by modeling the growth and division of Pediococcus acidilactici within the exponential phase. Estimations reveal the statistics of cell growth and division using only data from flow cytometry at a given time. From the relationship between the mother and daughter volumes, we also predict that P. acidilactici divide into two successive parallel planes.

Atmospheric and Geophysical Sciences Division Program Report, 1988--1989

Energy Technology Data Exchange (ETDEWEB)

1990-06-01

In 1990, the Atmospheric and Geophysical Sciences Division begins its 17th year as a division. As the Division has grown over the years, its modeling capabilities have expanded to include a broad range of time and space scales ranging from hours to decades and from local to global. Our modeling is now reaching out from its atmospheric focus to treat linkages with the oceans and the land. In this report, we describe the Division's goal and organizational structure. We also provide tables and appendices describing the Division's budget, personnel, models, and publications. 2 figs., 1 tab.

Health in police officers: Role of risk factor clusters and police divisions.

Science.gov (United States)

Habersaat, Stephanie A; Geiger, Ashley M; Abdellaoui, Sid; Wolf, Jutta M

2015-10-01

Law enforcement is a stressful occupation associated with significant health problems. To date, most studies have focused on one specific factor or one domain of risk factors (e.g., organizational, personal). However, it is more likely that specific combinations of risk factors are differentially health relevant and further, depend on the area of police work. A self-selected group of officers from the criminal, community, and emergency division (N = 84) of a Swiss state police department answered questionnaires assessing personal and organizational risk factors as well as mental and physical health indicators. In general, few differences were observed across divisions in terms of risk factors or health indicators. Cluster analysis of all risk factors established a high-risk and a low-risk cluster with significant links to all mental health outcomes. Risk cluster-by-division interactions revealed that, in the high-risk cluster, Emergency officers reported fewer physical symptoms, while community officers reported more posttraumatic stress symptoms. Criminal officers in the high-risk cluster tended to perceived more stress. Finally, perceived stress did not mediate the relationship between risk clusters and posttraumatic stress symptoms. In summary, our results support the notion that police officers are a heterogeneous population in terms of processes linking risk factors and health indicators. This heterogeneity thereby appeared to be more dependent on personal factors and individuals' perception of their own work conditions than division-specific work environments. Our findings further suggest that stress-reduction interventions that do not target job-relevant sources of stress may only show limited effectiveness in reducing health risks associated with police work. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biology Division progress report, October 1, 1991--September 30, 1993

Energy Technology Data Exchange (ETDEWEB)

Hartman, F.C.; Cook, J.S.

1993-10-01

This Progress Report summarizes the research endeavors of the Biology Division of the Oak Ridge National Laboratory during the period October 1, 1991, through September 30, 1993. The report is structured to provide descriptions of current activities and accomplishments in each of the Division`s major organizational units. Lists of information to convey the entire scope of the Division`s activities are compiled at the end of the report.

Radix-16 Combined Division and Square Root Unit

DEFF Research Database (Denmark)

Nannarelli, Alberto

2011-01-01

Division and square root, based on the digitrecurrence algorithm, can be implemented in a combined unit. Several implementations of combined division/square root units have been presented mostly for radices 2 and 4. Here, we present a combined radix-16 unit obtained by overlapping two radix-4...... result digit selection functions, as it is normally done for division only units. The latency of the unit is reduced by retiming and low power methods are applied as well. The proposed unit is compared to a radix-4 combined division/square root unit, and to a radix-16 unit, obtained by cascading two...

Engineering Physics Division progress report for period ending November 30, 1978

International Nuclear Information System (INIS)

Maienschein, F.C.

1979-01-01

Research and other activities of the Engineering Physics Division (formerly Neutron Physics Division) of ORNL during the period February 28, 1977 to November 30, 1978, are reported. The format is that of abstracts and summaries of prepared papers. Work is summarized in the following general areas: measurements of neutron cross sections and related quantities; cross-section theory, evaluations, and evaluation techniques; cross-section processing, testing, and sensitivity analyses; integral experiments and their analyses; development of methods for shield and reactor analyses; analyses for specific systems or applications (liquid-metal fast breeder reactor program, gas-cooled reactor program, alternate fuel cycle program, magnetic fusion energy program, high-energy physics program, accelerator breeding studies, miscellaneous studies); and information analysis and distribution. Overviews of each of these areas are included

Chemical Technology Division Annual Report 2000

International Nuclear Information System (INIS)

Lewis, D.; Gay, E. C.; Miller, J. F.; Einziger, R. E.; Green, D. W.

2001-01-01

The Chemical Technology Division (CMT) is one of eight engineering research divisions within Argonne National Laboratory (ANL), one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base through developing industrial technology and transferring that technology to industry. The Chemical Technology Division is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by ANL's mission. Additionally, the Division operates the Analytical Chemistry Laboratory, which provides a broad range of analytical services to ANL and other organizations. The Division is multi-disciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia, urban planning, and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature superconductors. In this annual report we present an overview of the technical programs together with representative highlights. The report is not intended to be comprehensive or encyclopedic, but to serve as an indication of the condition

Materials Sciences Division 1990 annual report

Energy Technology Data Exchange (ETDEWEB)

1990-12-31

This report is the Materials Sciences Division`s annual report. It contains abstracts describing materials research at the National Center for Electron Microscopy, and for research groups in metallurgy, solid-state physics, materials chemistry, electrochemical energy storage, electronic materials, surface science and catalysis, ceramic science, high tc superconductivity, polymers, composites, and high performance metals.

Earth Sciences Division, collected abstracts-1977

International Nuclear Information System (INIS)

Quitiquit, W.A.; Ledbetter, G.P.; Henry, A.L.

1978-01-01

This report is a compilation of abstracts of papers, internal reports, and talks presented during 1977 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore Laboratory. It is arranged alphabetically by author and includes a cross-reference by subject indicating the areas of research interest of the Earth Sciences Division

High School Sport Specialization Patterns of Current Division I Athletes.

Science.gov (United States)

Post, Eric G; Thein-Nissenbaum, Jill M; Stiffler, Mikel R; Brooks, M Alison; Bell, David R; Sanfilippo, Jennifer L; Trigsted, Stephanie M; Heiderscheit, Bryan C; McGuine, Timothy A

Sport specialization is a strategy to acquire superior sport performance in 1 sport but is associated with increased injury risk. Currently, the degree of high school specialization among Division I athletes is unknown. College athletes will display increased rates of specialization as they progress through their high school careers. Descriptive epidemiological study. Level 4. Three hundred forty-three athletes (115 female) representing 9 sports from a Midwest Division I University completed a previously utilized sport specialization questionnaire regarding sport participation patterns for each grade of high school. McNemar and chi-square tests were used to investigate associations of grade, sport, and sex with prevalence of sport specialization category (low, moderate, high) (a priori P ≤ 0.05). Specialization increased throughout high school, with 16.9% (n = 58) and 41.1% (n = 141) of athletes highly specialized in 9th and 12th grades, respectively. Football athletes were less likely to be highly specialized than nonfootball athletes for each year of high school ( P 0.23). The majority of Division I athletes were not classified as highly specialized throughout high school, but the prevalence of high specialization increased as athletes progressed through high school. Nonfootball athletes were more likely to be highly specialized than football athletes at each grade level. Most athletes who are recruited to participate in collegiate athletics will eventually specialize in their sport, but it does not appear that early specialization is necessary to become a Division I athlete. Athletes should be counseled regarding safe participation in sport during high school to minimize injury and maximize performance.

Nuclear size and cell division delay

International Nuclear Information System (INIS)

Bird, R.P.

1986-01-01

Radiation-induced division delay has been linked to damage at the nuclear envelope. Further, cells in G 2 phase are drastically arrested by high LET radiation such that single particles traversing cell nuclei may produce measurable division delay. A modest effort was initiated using two related cell lines of different size, near-diploid cells and near-tetraploid cells of Chinese hamster origin, to compare their sensitivity for radiation-induced division delay. If the nuclear surface is the critical target, then a larger nuclear cross-section presented to an alpha-particle beam should exhibit delay induced by a lesser particle fluence. Preliminary estimates of the extent of delay in asynchronous cultures following low doses of gamma-irradiation or of alpha-irradiation were made by in-situ observation of the time of onset of mitosis and by fixation and staining of cultures to determine the mitotic index as a function of time after irradiation. The basic approach to evaluating division delay will be to use Colecemid to accumulate mitotic cells over a period of time

Parallel optoelectronic trinary signed-digit division

Science.gov (United States)

Alam, Mohammad S.

1999-03-01

The trinary signed-digit (TSD) number system has been found to be very useful for parallel addition and subtraction of any arbitrary length operands in constant time. Using the TSD addition and multiplication modules as the basic building blocks, we develop an efficient algorithm for performing parallel TSD division in constant time. The proposed division technique uses one TSD subtraction and two TSD multiplication steps. An optoelectronic correlator based architecture is suggested for implementation of the proposed TSD division algorithm, which fully exploits the parallelism and high processing speed of optics. An efficient spatial encoding scheme is used to ensure better utilization of space bandwidth product of the spatial light modulators used in the optoelectronic implementation.

Empirical usability testing in a component-based environment : improving test efficiency with component-specific usability measures

NARCIS (Netherlands)

Brinkman, W.P.; Haakma, R.; Bouwhuis, D.G.; Bastide, R.; Palanque, P.; Roth, J.

2005-01-01

This paper addresses the issue of usability testing in a component-based software engineering environment, specifically measuring the usability of different versions of a component in a more powerful manner than other, more holistic, usability methods. Three component-specific usability measures are

Radiochemistry Division annual progress report : 1992

International Nuclear Information System (INIS)

Natarajan, V.; Godbole, S.V.; Iyer, R.H.

1994-01-01

The research and development activities of the Radiochemistry Division during 1992 are briefly described in the form of individual summaries grouped under the headings: 1) Nuclear Chemistry, 2) Actinide Chemistry, 3) Spectroscopy, and 4) Instrumentation. A list of publications numbering 95 by the scientific staff of the Division is also included in the report. (author). 35 figs., 56 tabs

Employee retention within the Information Technology Division of a South African Bank

Directory of Open Access Journals (Sweden)

Joy Mohlala

2012-05-01

Research purpose: To understand the challenges faced by the bank’s information technology leadership team to retain employees. Motivation for the study: To understand the challenges faced in attracting and retaining information technology professionals, and how this can serve as input for reducing skills shortages in Information Technology Divisions. Research design, approach and method: An interpretive approach employing a case study strategy and qualitative methods was employed. Semi structured interviews were conducted with thirteen senior managers and four directors of the bank’s Information Technology Division, who were selected on a purposive basis. Data were subjected to Creswell’s four stage data analysis process. Main findings: Findings indicate that employee turnover is the main contributor of skills shortages within the studied division. The lack of a retention strategy is making it difficult for leadership to identify crucial skills that must be retained. Practical/managerial implications: Evidence suggests that this bank, although they would like to retain information technology professionals, is not creating an environment conducive to do this, as little attention is paid to the unique demands of this group of employees. Contribution/value-add: This study investigates a specific group of employees for which a unique retention strategy does not exist. In understanding the challenges that impact on attracting and retaining information technology professionals, this study can contribute to the development of a retention strategy for these employees.

Division of Labor

KAUST Repository

Oke, Muse; Zaher, Manal S.; Hamdan, Samir

2014-01-01

The first assignment of DNA polymerases at the eukaryotic replication fork was possible after the in vitro reconstitution of the simian virus 40 (SV40) replication system. In this system, DNA polymerase α (Pol α) provides both leading and lagging strands with RNA-DNA primers that are extended by DNA polymerase δ (Pol δ). Extrapolating the architecture of the replication fork from the SV40 model system to an actual eukaryotic cell has been challenged by the discovery of a third DNA polymerase in Saccharomyces cerevisiae, DNA polymerase ε (Pol ε). A division of labor has been proposed for the eukaryotic replication fork whereby Pol ε replicates the leading strand and Pol δ replicates the lagging strand. However, an alternative model of unequal division of labor in which Pol δ can still participate in leading-strand synthesis is plausible.

Division of Labor

KAUST Repository

Oke, Muse

2014-09-12

The first assignment of DNA polymerases at the eukaryotic replication fork was possible after the in vitro reconstitution of the simian virus 40 (SV40) replication system. In this system, DNA polymerase α (Pol α) provides both leading and lagging strands with RNA-DNA primers that are extended by DNA polymerase δ (Pol δ). Extrapolating the architecture of the replication fork from the SV40 model system to an actual eukaryotic cell has been challenged by the discovery of a third DNA polymerase in Saccharomyces cerevisiae, DNA polymerase ε (Pol ε). A division of labor has been proposed for the eukaryotic replication fork whereby Pol ε replicates the leading strand and Pol δ replicates the lagging strand. However, an alternative model of unequal division of labor in which Pol δ can still participate in leading-strand synthesis is plausible.

Psychologists conducting Psychotherapy in 2012: current practices and historical trends among Division 29 members.

Science.gov (United States)

Norcross, John C; Rogan, Jessica D

2013-12-01

This study updates three similar investigations conducted in 1981, 1991, and 2001 on APA Division of Psychotherapy members in order to paint a contemporary portrait of psychologists conducting psychotherapy and to chronicle historical trends among Division 29 members. Four hundred twenty-eight psychologists (43% response) completed a questionnaire in 2012 regarding their demographic characteristics, professional activities, theoretical orientations, employment settings, and career experiences. The results point to an increasingly female and aging membership, which continues to be employed primarily in private practices and universities. Psychodynamic (27%), integrative (25%), and cognitive (17%) orientations continue to prevail. Professional activities have remained quite similar across the past 30 years with the exception of declines in projective testing and growth in neuropsychological and health testing. Training and career satisfactions remain high as well.

Physics division. Progress report, January 1, 1995--December 31, 1996

International Nuclear Information System (INIS)

Stewart, M.; Bacon, D.S.; Aine, C.J.; Bartsch, R.R.

1997-10-01

This issue of the Physics Division Progress Report describes progress and achievements in Physics Division research during the period January 1, 1995-December 31, 1996. The report covers the five main areas of experimental research and development in which Physics Division serves the needs of Los Alamos National Laboratory and the nation in applied and basic sciences: (1) biophysics, (2) hydrodynamic physics, (3) neutron science and technology, (4) plasma physics, and (5) subatomic physics. Included in this report are a message from the Division Director, the Physics Division mission statement, an organizational chart, descriptions of the research areas of the five groups in the Division, selected research highlights, project descriptions, the Division staffing and funding levels for FY95-FY97, and a list of publications and presentations

Physics division. Progress report, January 1, 1995--December 31, 1996

Energy Technology Data Exchange (ETDEWEB)

Stewart, M.; Bacon, D.S.; Aine, C.J.; Bartsch, R.R. [eds.] [comps.] [and others

1997-10-01

This issue of the Physics Division Progress Report describes progress and achievements in Physics Division research during the period January 1, 1995-December 31, 1996. The report covers the five main areas of experimental research and development in which Physics Division serves the needs of Los Alamos National Laboratory and the nation in applied and basic sciences: (1) biophysics, (2) hydrodynamic physics, (3) neutron science and technology, (4) plasma physics, and (5) subatomic physics. Included in this report are a message from the Division Director, the Physics Division mission statement, an organizational chart, descriptions of the research areas of the five groups in the Division, selected research highlights, project descriptions, the Division staffing and funding levels for FY95-FY97, and a list of publications and presentations.

Nuclear Chemistry Division annual report FY83

International Nuclear Information System (INIS)

Struble, G.

1983-01-01

The purpose of the annual reports of the Nuclear Chemistry Division is to provide a timely summary of research activities pursued by members of the Division during the preceding year. Throughout, details are kept to a minimum; readers desiring additional information are encouraged to read the referenced documents or contact the authors. The Introduction presents an overview of the Division's scientific and technical programs. Next is a section of short articles describing recent upgrades of the Division's major facilities, followed by sections highlighting scientific and technical advances. These are grouped under the following sections: nuclear explosives diagnostics; geochemistry and environmental sciences; safeguards technology and radiation effect; and supporting fundamental science. A brief overview introduces each section. Reports on research supported by a particular program are generally grouped together in the same section. The last section lists the scientific, administrative, and technical staff in the Division, along with visitors, consultants, and postdoctoral fellows. It also contains a list of recent publications and presentations. Some contributions to the annual report are classified and only their abstracts are included in this unclassified portion of the report (UCAR-10062-83/1); the full article appears in the classified portion (UCAR-10062-83/2)

The ACS-NUCL Division 50th Anniversary: Introduction

Energy Technology Data Exchange (ETDEWEB)

Hobart, David E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-01-10

The ACS Division of Nuclear Chemistry and Technology was initiated in 1955 as a subdivision of the Division of Industrial and Engineering Chemistry. Probationary divisional status was lifted in 1965. The Division’s first symposium was held in Denver in 1964 and it is fitting that we kicked-off the 50th Anniversary in Denver in the spring of 2015. Listed as a small ACS Division with only about 1,000 members, NUCL’s impact over the past fifty years has been remarkable. National ACS meetings have had many symposia sponsored or cosponsored by NUCL that included Nobel Laureates, U.S. Senators, other high-ranking officials and many students as speakers. The range of subjects has been exceptional as are the various prestigious awards established by the Division. Of major impact has been the past 30 years of the NUCL Nuclear Chemistry Summer Schools to help fill the void of qualified nuclear scientists and technicians. In celebrating the 50th Anniversary we honor the past, celebrate the present and shape the future of the Division and nuclear science and technology. To celebrate this auspicious occasion a commemorative lapel pin has been designed for distribution to NUCL Division members.

Concept for waste package environment tests in the Yucca Mountain exploratory shaft

International Nuclear Information System (INIS)

Yow, J.L. Jr.

1985-05-01

The Nevada Nuclear Waste Storage Investigations (NNWSI) project is studying a tuffaceous rock unit located at Yucca Mountain on the western boundary of the Nevada Test Site, Nye County, Nevada. The objective is to evaluate the suitability of the volcanic rocks located above the water table at Yucca Mountain as a potential location for a repository for high level radioactive waste. As part of the NNWSI project, Lawrence Livermore National Laboratory is responsible for the design of the waste package and for determining the expected performance of the waste package in the repository environment. To design an optimal waste package system for the unsaturated emplacement environment, the mechanisms by which liquid water can return to contact the metal canister after peaking of the thermal load must be established. Definition of these flux and flow mechanisms is essential for estimating canister corrosion modes and rates. Therefore, three waste package environment tests are being designed for the in situ phase of exploratory shaft testing. These tests emphasize measurement techniques that offer the possibility of characterizing the movement of water into and through the pores and fractures of the densely welded Topopah Spring Member. Other measurement techniques will be used to examine the interactions between moisture migration and the thermomechanical rock mass behavior. Three reduced-scale heater tests will use electrical resistive heaters in a horizontal configuration. All three tests are designed to investigate moisture conditions in the rock during heating and cooling phases of a thermal cycle so that the effects of these moisture conditions on the performance of the waste package system may be established. 28 refs., 4 figs., 3 tabs

QUEST/Ada: Query utility environment for software testing of Ada

Science.gov (United States)

Brown, David B.

1989-01-01

Results of research and development efforts are presented for Task 1, Phase 2 of a general project entitled, The Development of a Program Analysis Environment for Ada. A prototype of the QUEST/Ada system was developed to collect data to determine the effectiveness of the rule-based testing paradigm. The prototype consists of five parts: the test data generator, the parser/scanner, the test coverage analyzer, a symbolic evaluator, and a data management facility, known as the Librarian. These components are discussed at length. Also presented is an experimental design for the evaluations, an overview of the project, and a schedule for its completion.

24 CFR 4.36 - Action by the Ethics Law Division.

Science.gov (United States)

2010-04-01

... violation is material, the Ethics Law Division shall consider the following factors, as applicable: (1) The... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Action by the Ethics Law Division... the Ethics Law Division. (a) After review of the Inspector General's report, the Ethics Law Division...

The global resource balance table, an integrated table of energy, materials and the environment

International Nuclear Information System (INIS)

Tsuchiya, Haruki

2013-01-01

This paper introduces the Global Resource Balance Table (GRBT), which is an extension of the energy balance tables that expresses the relationships between energy, materials and the environment. The material division of the GRBT includes steel, cement, paper, wood and grain. In contrast, the environmental division of the GRBT includes oxygen, CO 2 and methane. The transaction division rows in the GRBT include production, conversion, end use and stock. Each cell of the GRBT contains the quantities of the respective resources that were generated or consumed. The relationships between the cells were constructed from the laws of conservation of the materials and energy. We constructed a GRBT for 2007 and discussed the increasing air temperature due to waste heat and the CO 2 equivalent from human breathing. The GRBT is a comprehensive integrated table that represents the resources that are consumed by human activities and is useful for energy and environmental studies. - Highlights: • We extended energy balance table and introduced Global Resource Balance Table. • It shows relationships between energy, materials and the environment. • The material division includes steel, cement, paper, wood and grain. • The environmental division includes oxygen, CO 2 and methane. • We discussed on waste heat and CO 2 emission by human breathing

Star Excursion Balance Test Performance Varies by Sport in Healthy Division I Collegiate Athletes.

Science.gov (United States)

Stiffler, Mikel R; Sanfilippo, Jennifer L; Brooks, M Alison; Heiderscheit, Bryan C

2015-10-01

Cross-sectional. To describe performance and asymmetry on the Star Excursion Balance Test (SEBT) by sex and sport, and to determine if differences exist within a collegiate athlete population. Performance on the SEBT may differ between sexes and levels of competition, though the results of previous studies have been inconsistent. Investigation of performance and asymmetry differences between sports is limited. Sex- and sport-specific reference values likely need to be determined to best assess SEBT performance. Performance on the SEBT was retrospectively reviewed in 393 healthy National Collegiate Athletic Association Division I collegiate athletes from 8 sports. Means, standard deviations, and 95% confidence intervals were calculated for all variables. Normalized reach distance (percent limb length) and asymmetry between limbs were compared for the anterior (ANT), posterolateral (PL), and posteromedial (PM) directions and for the composite (COMP) score using a 2-way analysis of variance (ANOVA) of sex by sport, and a 1-way ANOVA to separately compare sports within each sex. Average normalized reach distance ranged from 62% to 69%, 84% to 97%, and 99% to 113% in the ANT, PL, and PM directions, respectively, and from 82% to 92% in the COMP score. Normalized asymmetry ranged from 3% to 4%, 5% to 8%, and 5% to 6% in the ANT, PL, and PM directions, respectively. A significant sex-by-sport interaction (P = .039) was observed in the ANT direction, with a sex effect for soccer players (Psport.

Lead from the center. How to manage divisions dynamically.

Science.gov (United States)

Raynor, M E; Bower, J L

2001-05-01

Conventional wisdom holds that a company's divisions should be given almost total autonomy--especially under conditions of uncertainty--because they are closer to emerging technologies, customers, and competitors than corporate headquarters could ever be. But research from Michael Raynor and Joseph Bower suggests that the corporate office should be more, not less, directive in turbulent markets. Rapid changes in an industry make it difficult to predict where and when synergies among divisions might emerge. With so many possibilities and such uncertainty, companies can't afford to sacrifice their ability to flexibly execute business strategy. Corporate headquarters must play an active role in defining the scope of division-level strategy, the authors say, so that divisions do not act in ways that undermine opportunities to collaborate in the future. But neither can companies afford to sacrifice the competitiveness of their divisions as stand-alone businesses. In creating corporate-level strategic flexibility, a corporate office must balance the need for divisional autonomy now with the potential need for cooperation in the future. Through an examination of four corporations--Sprint, WPP, Teradyne, and Viacom--the authors challenge traditional approaches to diversification in which a company's divisions are either related (they share resources and collaborate) or unrelated (they compete for resources and operate as stand-alone businesses). They argue that companies should adopt a dynamic approach to cooperation among divisions, enabling varying degrees of relatedness between divisions depending on strategic circumstances. The authors offer four tactics to help executives manage divisions dynamically.

Reactor Engineering Division Material for World Wide Web Pages

International Nuclear Information System (INIS)

1996-01-01

This document presents the home page of the Reactor Engineering Division of Argonne National Laboratory. This WWW site describes the activities of the Division, an introduction to its wide variety of programs and samples of the results of research by people in the division

Health Physics Division annual report for the period ending December 31, 1972 Part I : Research and development

International Nuclear Information System (INIS)

1973-01-01

The Health Physics Division of the Bhabha Atomic Research Centre, Bombay (India) is responsible for: (i) assessment and control of radiation and industrial hazards in various research establishments and industrial installations of the Department of Atomic Energy and (ii) prescribing limits and conditions in respect of waste releases to the environment from the above establishments and installations. For effective discharge of these responsibilities, the Division is engaged in various research programmes in the following areas: (1) radiation dosimetry (2) instrumentation (3) pollution (4) environmental radioactivity, both natural and artificial (5) radioactive contamination and nuclear safety (6) industrial hygiene and safety (7) radioecology (8) micrometeorology. These programmes are described in brief. (M.G.B.)

Medical Sciences Division report for 1993

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

This year`s Medical Sciences Division (MSD) Report is organized to show how programs in our division contribute to the core competencies of Oak Ridge Institute for Science and Education (ORISE). ORISE`s core competencies in education and training, environmental and safety evaluation and analysis, occupational and environmental health, and enabling research support the overall mission of the US Department of Energy (DOE).

Medical Sciences Division report for 1993

International Nuclear Information System (INIS)

1993-01-01

This year's Medical Sciences Division (MSD) Report is organized to show how programs in our division contribute to the core competencies of Oak Ridge Institute for Science and Education (ORISE). ORISE's core competencies in education and training, environmental and safety evaluation and analysis, occupational and environmental health, and enabling research support the overall mission of the US Department of Energy (DOE)

Association between biliary complications and technique of hilar division (extrahepatic vs. intrahepatic in major liver resections

Directory of Open Access Journals (Sweden)

Gamaletsos Evangelos

2006-08-01

Full Text Available Abstract Background Division of major vascular and biliary structures during major hepatectomies can be carried out either extrahepatically at the porta hepatic or intrahepatically during the parenchymal transection. In this retrospective study we test the hypothesis that the intrahepatic technique is associated with less early biliary complications. Methods 150 patients who underwent major hepatectomies were retrospectively allocated into an intrahepatic group (n = 100 and an extrahepatic group (n = 50 based on the technique of hilar division. The two groups were operated by two different surgical teams, each one favoring one of the two approaches for hilar dissection. Operative data (warm ischemic time, operative time, blood loss, biliary complications, morbidity and mortality rates were analyzed. Results In extrahepatic patients, operative time was longer (245 ± 50 vs 214 ± 38 min, p Conclusion Intrahepatic hilar division is as safe as extrahepatic hilar division in terms of intraoperative blood requirements, morbidity and mortality. The extrahepatic technique is associated with more severe bile leaks and biliary injuries.

The Performance test of Mechanical Sodium Pump with Water Environment

International Nuclear Information System (INIS)

Cho, Chungho; Kim, Jong-Man; Ko, Yung Joo; Jeong, Ji-Young; Kim, Jong-Bum; Ko, Bock Seong; Park, Sang Jun; Lee, Yoon Sang

2015-01-01

As contrasted with PWR(Pressurized light Water Reactor) using water as a coolant, sodium is used as a coolant in SFR because of its low melting temperature, high thermal conductivity, the high boiling temperature allowing the reactors to operate at ambient pressure, and low neutron absorption cross section which is required to achieve a high neutron flux. But, sodium is violently reactive with water or oxygen like the other alkali metal. So Very strict requirements are demanded to design and fabricate of sodium experimental facilities. Furthermore, performance testing in high temperature sodium environments is more expensive and time consuming and need an extra precautions because operating and maintaining of sodium experimental facilities are very difficult. The present paper describes performance test results of mechanical sodium pump with water which has been performed with some design changes using water test facility in SAM JIN Industrial Co. To compare the hydraulic characteristic of model pump with water and sodium, the performance test of model pump were performed using vender's experimental facility for mechanical sodium pump. To accommodate non-uniform thermal expansion and to secure the operability and the safety, the gap size of some parts of original model pump was modified. Performance tests of modified mechanical sodium pump with water were successfully performed. Water is therefore often selected as a surrogate test fluid because it is not only cheap, easily available and easy to handle but also its important hydraulic properties (density and kinematic viscosity) are very similar to that of the sodium. Normal practice to thoroughly test a design or component before applied or installed in reactor is important to ensure the safety and operability in the sodium-cooled fast reactor (SFR). So, in order to estimate the hydraulic behavior of the PHTS pump of DSFR (600 MWe Demonstraion SFR), the performance tests of the model pump such as performance

QUEST/Ada (Query Utility Environment for Software Testing of Ada): The development of a prgram analysis environment for Ada, task 1, phase 2

Science.gov (United States)

Brown, David B.

1990-01-01

The results of research and development efforts are described for Task one, Phase two of a general project entitled The Development of a Program Analysis Environment for Ada. The scope of this task includes the design and development of a prototype system for testing Ada software modules at the unit level. The system is called Query Utility Environment for Software Testing of Ada (QUEST/Ada). The prototype for condition coverage provides a platform that implements expert system interaction with program testing. The expert system can modify data in the instrument source code in order to achieve coverage goals. Given this initial prototype, it is possible to evaluate the rule base in order to develop improved rules for test case generation. The goals of Phase two are the following: (1) to continue to develop and improve the current user interface to support the other goals of this research effort (i.e., those related to improved testing efficiency and increased code reliable); (2) to develop and empirically evaluate a succession of alternative rule bases for the test case generator such that the expert system achieves coverage in a more efficient manner; and (3) to extend the concepts of the current test environment to address the issues of Ada concurrency.

Modeling the Gas Dynamics Environment in a Subscale Solid Rocket Test Motor

Science.gov (United States)

Eaton, Andrew M.; Ewing, Mark E.; Bailey, Kirk M.; McCool, Alex (Technical Monitor)

2001-01-01

Subscale test motors are often used for the evaluation of solid rocket motor component materials such as internal insulation. These motors are useful for characterizing insulation performance behavior, screening insulation material candidates and obtaining material thermal and ablative property design data. One of the primary challenges associated with using subscale motors however, is the uncertainty involved when extrapolating the results to full-scale motor conditions. These uncertainties are related to differences in such phenomena as turbulent flow behavior and boundary layer development, propellant particle interactions with the wall, insulation off-gas mixing and thermochemical reactions with the bulk flow, radiation levels, material response to the local environment, and other anomalous flow conditions. In addition to the need for better understanding of physical mechanisms, there is also a need to better understand how to best simulate these phenomena using numerical modeling approaches such as computational fluid dynamics (CFD). To better understand and model interactions between major phenomena in a subscale test motor, a numerical study of the internal flow environment of a representative motor was performed. Simulation of the environment included not only gas dynamics, but two-phase flow modeling of entrained alumina particles like those found in an aluminized propellant, and offgassing from wall surfaces similar to an ablating insulation material. This work represents a starting point for establishing the internal environment of a subscale test motor using comprehensive modeling techniques, and lays the groundwork for improving the understanding of the applicability of subscale test data to full-scale motors. It was found that grid resolution, and inclusion of phenomena in addition to gas dynamics, such as two-phase and multi-component gas composition are all important factors that can effect the overall flow field predictions.

Similar effects of substance P on learning and memory function between hippocampus and striatal marginal division

Science.gov (United States)

Yu, Yan; Zeng, Changchun; Shu, Siyun; Liu, Xuemei; Li, Chuhua

2014-01-01

Substance P is an endogenous neurokinin that is present in the central and peripheral nervous systems. The neuropeptide substance P and its high-affinity receptor neurokinin 1 receptor are known to play an important role in the central nervous system in inflammation, blood pressure, motor behavior and anxiety. The effects of substance P in the hippocampus and the marginal division of the striatum on memory remain poorly understood. Compared with the hippocampus as a control, immunofluorescence showed high expression of the substance P receptor, neurokinin 1, in the marginal division of the striatum of normal rats. Unilateral or bilateral injection of an antisense oligonucleotide against neurokinin 1 receptor mRNA in the rat hippocampus or marginal division of the striatum effectively reduced neurokinin 1 receptor expression. Independent of injection site, rats that received this antisense oligonucleotide showed obviously increased footshock times in a Y-maze test. These results indicate that the marginal division of the striatum plays a similar function in learning and memory to the hippocampus, which is a valuable addition to our mechanistic understanding of the learning and memory functions of the marginal division of the striatum. PMID:25206901

15 CFR 950.8 - Satellite Data Services Division (SDSD).

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Satellite Data Services Division (SDSD... THE ENVIRONMENTAL DATA SERVICE ENVIRONMENTAL DATA AND INFORMATION § 950.8 Satellite Data Services Division (SDSD). The Satellite Data Services Division of the EDIS National Climatic Center provides...

Division of Agriculture

Science.gov (United States)

Department of Natural Resources logo, color scheme Department of Natural Resources Division of Agriculture Search Search DNR's site DNR State of Alaska Toggle main menu visibility Agriculture Home Programs Asset Disposals Alaska Caps Progam Board of Agriculture & Conservation Farm To School Program Grants

Development and psychometric testing of the Nursing Workplace Relational Environment Scale (NWRES).

Science.gov (United States)

Duddle, Maree; Boughton, Maureen

2009-03-01

The aim of this study was to develop and test the psychometric properties of the Nursing Workplace Relational Environment Scale (NWRES). A positive relational environment in the workplace is characterised by a sense of connectedness and belonging, support and cooperation among colleagues, open communication and effectively managed conflict. A poor relational environment in the workplace may contribute to job dissatisfaction and early turnover of staff. Quantitative survey. A three-stage process was used to design and test the NWRES. In Stage 1, an extensive literature review was conducted on professional working relationships and the nursing work environment. Three key concepts; collegiality, workplace conflict and job satisfaction were identified and defined. In Stage 2, a pool of items was developed from the dimensions of each concept and formulated into a 35-item scale which was piloted on a convenience sample of 31 nurses. In Stage 3, the newly refined 28-item scale was administered randomly to a convenience sample of 150 nurses. Psychometric testing was conducted to establish the construct validity and reliability of the scale. Exploratory factor analysis resulted in a 22-item scale. The factor analysis indicated a four-factor structure: collegial behaviours, relational atmosphere, outcomes of conflict and job satisfaction which explained 68.12% of the total variance. Cronbach's alpha coefficient for the NWRES was 0.872 and the subscales ranged from 0.781-0.927. The results of the study confirm the reliability and validity of the NWRES. Replication of this study with a larger sample is indicated to determine relationships among the subscales. The results of this study have implications for health managers in terms of understanding the impact of the relational environment of the workplace on job satisfaction and retention.

Quantitative regulation of B cell division destiny by signal strength.

Science.gov (United States)

Turner, Marian L; Hawkins, Edwin D; Hodgkin, Philip D

2008-07-01

Differentiation to Ab secreting and isotype-switched effector cells is tightly linked to cell division and therefore the degree of proliferation strongly influences the nature of the immune response. The maximum number of divisions reached, termed the population division destiny, is stochastically distributed in the population and is an important parameter in the quantitative outcome of lymphocyte responses. In this study, we further assessed the variables that regulate B cell division destiny in vitro in response to T cell- and TLR-dependent stimuli. Both the concentration and duration of stimulation were able to regulate the average maximum number of divisions undergone for each stimulus. Notably, a maximum division destiny was reached during provision of repeated saturating stimulation, revealing that an intrinsic limit to proliferation exists even under these conditions. This limit was linked directly to division number rather than time of exposure to stimulation and operated independently of the survival regulation of the cells. These results demonstrate that a B cell population's division destiny is regulable by the stimulatory conditions up to an inherent maximum value. Division destiny is a crucial parameter in regulating the extent of B cell responses and thereby also the nature of the immune response mounted.

Parkin suppresses Drp1-independent mitochondrial division

Energy Technology Data Exchange (ETDEWEB)

Roy, Madhuparna, E-mail: mroy17@jhmi.edu; Itoh, Kie, E-mail: kito5@jhmi.edu; Iijima, Miho, E-mail: miijima@jhmi.edu; Sesaki, Hiromi, E-mail: hsesaki@jhmi.edu

2016-07-01

The cycle of mitochondrial division and fusion disconnect and reconnect individual mitochondria in cells to remodel this energy-producing organelle. Although dynamin-related protein 1 (Drp1) plays a major role in mitochondrial division in cells, a reduced level of mitochondrial division still persists even in the absence of Drp1. It is unknown how much Drp1-mediated mitochondrial division accounts for the connectivity of mitochondria. The role of a Parkinson’s disease-associated protein—parkin, which biochemically and genetically interacts with Drp1—in mitochondrial connectivity also remains poorly understood. Here, we quantified the number and connectivity of mitochondria using mitochondria-targeted photoactivatable GFP in cells. We show that the loss of Drp1 increases the connectivity of mitochondria by 15-fold in mouse embryonic fibroblasts (MEFs). While a single loss of parkin does not affect the connectivity of mitochondria, the connectivity of mitochondria significantly decreased compared with a single loss of Drp1 when parkin was lost in the absence of Drp1. Furthermore, the loss of parkin decreased the frequency of depolarization of the mitochondrial inner membrane that is caused by increased mitochondrial connectivity in Drp1-knockout MEFs. Therefore, our data suggest that parkin negatively regulates Drp1-indendent mitochondrial division. -- Highlights: •A Drp1-mediated mechanism accounts for ∼95% of mitochondrial division. •Parkin controls the connectivity of mitochondria via a mechanism that is independent of Drp1. •In the absence of Drp1, connected mitochondria transiently depolarize. •The transient depolarization is independent of calcium signaling and uncoupling protein 2.

Parkin suppresses Drp1-independent mitochondrial division

International Nuclear Information System (INIS)

Roy, Madhuparna; Itoh, Kie; Iijima, Miho; Sesaki, Hiromi

2016-01-01

The cycle of mitochondrial division and fusion disconnect and reconnect individual mitochondria in cells to remodel this energy-producing organelle. Although dynamin-related protein 1 (Drp1) plays a major role in mitochondrial division in cells, a reduced level of mitochondrial division still persists even in the absence of Drp1. It is unknown how much Drp1-mediated mitochondrial division accounts for the connectivity of mitochondria. The role of a Parkinson’s disease-associated protein—parkin, which biochemically and genetically interacts with Drp1—in mitochondrial connectivity also remains poorly understood. Here, we quantified the number and connectivity of mitochondria using mitochondria-targeted photoactivatable GFP in cells. We show that the loss of Drp1 increases the connectivity of mitochondria by 15-fold in mouse embryonic fibroblasts (MEFs). While a single loss of parkin does not affect the connectivity of mitochondria, the connectivity of mitochondria significantly decreased compared with a single loss of Drp1 when parkin was lost in the absence of Drp1. Furthermore, the loss of parkin decreased the frequency of depolarization of the mitochondrial inner membrane that is caused by increased mitochondrial connectivity in Drp1-knockout MEFs. Therefore, our data suggest that parkin negatively regulates Drp1-indendent mitochondrial division. -- Highlights: •A Drp1-mediated mechanism accounts for ∼95% of mitochondrial division. •Parkin controls the connectivity of mitochondria via a mechanism that is independent of Drp1. •In the absence of Drp1, connected mitochondria transiently depolarize. •The transient depolarization is independent of calcium signaling and uncoupling protein 2.

The sexual division of leadership in volunteer emergency medical service squads.

Science.gov (United States)

Thompson, A M

1995-01-01

This article reports on theoretical and empirical research that explored the hypothesis that there is a sexual division of leadership in volunteer emergency medical service (EMS) squads. This hypothesis was tested against survey data obtained from 216 current members of nine upstate New York volunteer EMS squads. Despite several mitigating characteristics of these organizations, and despite the lack of supporting statistical evidence at the aggregate level of officership, the research found statistically significant confirmation of sex bias in officer selection when leadership was disaggregated into line and staff officer positions. Medical qualifications and length of EMS squad membership were also included in the model as determinants of leadership experience. These results are discussed relative to the question of the sexual division of leadership in the overarching nonprofit and voluntary sector of the U.S. economy.

Prototype heater test of the environment around a simulated waste package

International Nuclear Information System (INIS)

Ramirez, A.L.; Buscheck, T.A.; Carlson, R.; Daily, W.; Latorre, V.R.; Lee, K; Lin, Wunan; Mao, Nai-hsien; Towse, D.; Ueng, Tzou-Shin; Watwood, D.

1991-01-01

This paper presents selected results obtained during the 301 day duration of the Prototype Engineered Barrier System Field Test (PEBSFT) performed in G-Tunnel within the Nevada Test Site. The test described is a precursor to the Engineered Barrier Systems Field Tests (EBSFT) planned for the Exploratory Shaft Facility in Yucca Mountain. The EBSFT will consist of in situ tests of the geohydrologic and geochemical environment in the near field (within a few meters) of heaters emplaced in welded tuff to simulate the thermal effects of waste packages. The paper discusses the evolution of hydrothermal behavior during the prototype test, including rock temperatures, changes in rock moisture content, air permeability of fractures and gas-phase humidity in the heater borehole

Developing Deaf Students Fraction Skills Requires Understanding Magnitude and Whole Number Division

Science.gov (United States)

Mousley, Keith; Kelly, Ronald R.

2018-01-01

Research has shown that fraction magnitude and whole number division are important precursors to learning and understanding fractions. Deaf and hard-of-hearing (DHH) students are consistently challenged with learning fractions from K-12 through college. Sixty DHH college students were tested for both their understanding of magnitude between two…

Publications - Geospatial Data | Alaska Division of Geological &

Science.gov (United States)

from rocks collected in the Richardson mining district, Big Delta Quadrangle, Alaska: Alaska Division Island 2009 topography: Alaska Division of Geological & Geophysical Surveys Miscellaneous Publication , Geologic map of portions of the Livengood B-3, B-4, C-3, and C-4 quadrangles, Tolovana mining district

Biology Division progress report, October 1, 1993--September 30, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

This Progress Report summarizes the research endeavors of the Biology Division of the Oak Ridge National Laboratory during the period October 1, 1993, through September 30, 1995. The report is structured to provide descriptions of current activities and accomplishments in each of the Division`s major organizational units. Lists of information to convey the entire scope of the Division`s activities are compiled at the end of the report. Attention is focused on the following research activities: molecular, cellular, and cancer biology; mammalian genetics and development; genome mapping program; and educational activities.

Biology and Medicine Division: Annual report 1986

International Nuclear Information System (INIS)

1987-04-01

The Biology and Medicine Division continues to make important contributions in scientific areas in which it has a long-established leadership role. For 50 years the Division has pioneered in the application of radioisotopes and charged particles to biology and medicine. There is a growing emphasis on cellular and molecular applications in the work of all the Division's research groups. The powerful tools of genetic engineering, the use of recombinant products, the analytical application of DNA probes, and the use of restriction fragment length polymorphic DNA are described and proposed for increasing use in the future

Biology and Medicine Division: Annual report 1986

Energy Technology Data Exchange (ETDEWEB)

1987-04-01

The Biology and Medicine Division continues to make important contributions in scientific areas in which it has a long-established leadership role. For 50 years the Division has pioneered in the application of radioisotopes and charged particles to biology and medicine. There is a growing emphasis on cellular and molecular applications in the work of all the Division's research groups. The powerful tools of genetic engineering, the use of recombinant products, the analytical application of DNA probes, and the use of restriction fragment length polymorphic DNA are described and proposed for increasing use in the future.

Mapping Urban Social Divisions

Directory of Open Access Journals (Sweden)

Susan Ball

2010-05-01

Full Text Available Against the background of increased levels of interest in space and images beyond the field of geography, this article (re- introduces earlier work on the semiotics of maps undertaken by geographers in the 1960s. The data limitations, purpose and cultural context in which a user interprets a map's codes and conventions are highlighted in this work, which remains relevant to the interpretation of maps—new and old—forty years later. By means of drawing on geography's contribution to the semiotics of maps, the article goes on to examine the concept of urban social divisions as represented in map images. Using a small number of map images, including two of the most widely known maps of urban social division in Europe and North America, the roles of context, data and purpose in the production and interpretation of maps are discussed. By presenting the examples chronologically the article shows that although advances in data collection and manipulation have allowed researchers to combine different social variables in maps of social division, and to interact with map images, work by geographers on the semiotics of maps is no less relevant today than when it was first proposed forty years ago. URN: urn:nbn:de:0114-fqs1002372

Using a Research-based Approach to Transform Upper-division Courses in Classical and Quantum Mechanics and E&M

Science.gov (United States)

Pollock, Steven

2013-04-01

At most universities, including the University of Colorado, upper-division physics courses are taught using a traditional lecture approach that does not make use of many of the instructional techniques that have been found to improve student learning at the introductory level. We are transforming several upper-division courses using principles of active engagement and learning theory, guided by the results of observations, interviews, and analysis of student work at CU and elsewhere. In this talk I outline these transformations, including the development of faculty consensus learning goals, clicker questions, tutorials, modified homeworks, and more. We present evidence of the effectiveness of these transformations relative to traditional courses, based on student grades, interviews, and through research-based assessments of student conceptual mastery and student attitudes. Our results suggest that many of the tools that have been effective in introductory courses are effective for our majors, and that further research is warranted in the upper-division environment. (See www.colorado.edu/sei/departments/physics.htm for materials)

Nuclear Chemistry Division annual report FY83

Energy Technology Data Exchange (ETDEWEB)

Struble, G. (ed.)

1983-01-01

The purpose of the annual reports of the Nuclear Chemistry Division is to provide a timely summary of research activities pursued by members of the Division during the preceding year. Throughout, details are kept to a minimum; readers desiring additional information are encouraged to read the referenced documents or contact the authors. The Introduction presents an overview of the Division's scientific and technical programs. Next is a section of short articles describing recent upgrades of the Division's major facilities, followed by sections highlighting scientific and technical advances. These are grouped under the following sections: nuclear explosives diagnostics; geochemistry and environmental sciences; safeguards technology and radiation effect; and supporting fundamental science. A brief overview introduces each section. Reports on research supported by a particular program are generally grouped together in the same section. The last section lists the scientific, administrative, and technical staff in the Division, along with visitors, consultants, and postdoctoral fellows. It also contains a list of recent publications and presentations. Some contributions to the annual report are classified and only their abstracts are included in this unclassified portion of the report (UCAR-10062-83/1); the full article appears in the classified portion (UCAR-10062-83/2).

Lower Quarter Y-Balance Test Scores and Lower Extremity Injury in NCAA Division I Athletes.

Science.gov (United States)

Lai, Wilson C; Wang, Dean; Chen, James B; Vail, Jeremy; Rugg, Caitlin M; Hame, Sharon L

2017-08-01

Functional movement tests that are predictive of injury risk in National Collegiate Athletic Association (NCAA) athletes are useful tools for sports medicine professionals. The Lower Quarter Y-Balance Test (YBT-LQ) measures single-leg balance and reach distances in 3 directions. To assess whether the YBT-LQ predicts the laterality and risk of sports-related lower extremity (LE) injury in NCAA athletes. Case-control study; Level of evidence, 3. The YBT-LQ was administered to 294 NCAA Division I athletes from 21 sports during preparticipation physical examinations at a single institution. Athletes were followed prospectively over the course of the corresponding season. Correlation analysis was performed between the laterality of reach asymmetry and composite scores (CS) versus the laterality of injury. Receiver operating characteristic (ROC) analysis was used to determine the optimal asymmetry cutoff score for YBT-LQ. A multivariate regression analysis adjusting for sex, sport type, body mass index, and history of prior LE surgery was performed to assess predictors of earlier and higher rates of injury. Neither the laterality of reach asymmetry nor the CS correlated with the laterality of injury. ROC analysis found optimal cutoff scores of 2, 9, and 3 cm for anterior, posteromedial, and posterolateral reach, respectively. All of these potential cutoff scores, along with a cutoff score of 4 cm used in the majority of prior studies, were associated with poor sensitivity and specificity. Furthermore, none of the asymmetric cutoff scores were associated with earlier or increased rate of injury in the multivariate analyses. YBT-LQ scores alone do not predict LE injury in this collegiate athlete population. Sports medicine professionals should be cautioned against using the YBT-LQ alone to screen for injury risk in collegiate athletes.

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1978-10-01

Research activities in the Division of Reactor Engineering in fiscal 1977 are described. Works of the Division are development of multi-purpose Very High Temperature Gas Cooled Reactor, fusion reactor engineering, and development of Liquid Metal Fast Breeder Reactor for Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology, and Committee on Reactor Physics. (Author)

Hardware-in-the-Loop environment for testing and commissioning of space controllers; Hardware-in-the-Loop Umgebung zum Test und zur Inbetriebnahme von Raumreglern

Energy Technology Data Exchange (ETDEWEB)

Adlhoch, Alexander; Becker, Martin [Hochschule Biberach (Germany). Inst. fuer Gebaeude- und Energiesysteme

2012-07-01

The energy-efficient and optimal functioning of room controllers in terms of indoor air climates is influenced mainly by the control algorithm and the optimal adjustment of the parameters of controllers used in terms of space requirements. In the practical operation, deficits in the function or parameters of the controller are hardly or only with great effort metrological detectable, but have a significant impact on the energy consumption and / or the indoor climate comfort. In a hardware-in-the-loop (HIL) environment, room controllers can be examined in terms of the function under defined conditions, and different controllers can be evaluated comparatively. It is also possible to adjust the parameters of the controller before the commissioning. The HiL environment presented in the contribution under consideration consists of a model of the controlled system, a hardware coupler and a real controller to be tested. Among the spatial models, it can be selected from a plurality of different types of space which in turn can be assigned by means of different spatial parameters and environmental models. These combinations enable a replication of a test scenario corresponding to the later application. The hardware coupler provides a selection of physical inputs and outputs as well as interfaces to different bus systems (for example KNX, LON, EnOcean) for connecting different types of controllers. The construction and operation of a HIL test stand for space controller is presented based on first practical control tests. At this, the focus is on the suitability of this test environment for a variety of different controllers as well as development assistance and assistance for the adjustment of parameters. The HiL environments developed in the joint research project HiL RHK1 for the testing of space controllers, controllers for HVAC systems and refrigeration technology controllers have been developed so that the HiL environments can be coupled to a multi-HIL environment. This

Thermomechanical scoping calculations for the waste package environment tests

International Nuclear Information System (INIS)

Butkovich, T.R.; Yow, J.L. Jr.

1986-03-01

During the site characterization phase of the Nevada Nuclear Waste Storage Investigation Project, tests are planned to provide field information on the hydrological and thermomechanical environment. These results are needed for assessing performance of stored waste packages emplaced at depth in excavations in a rock mass. Scoping calculations were performed to provide information on displacements and stress levels attained around excavations in the rock mass from imposing a thermal load designed to simulate the heat produced by radioactive decay. In this way, approximate levels of stresses and displacements are available for choosing instrumentation type and sensitivity as well as providing indications for optimizing instrument emplacement during the test. 7 refs., 9 figs., 1 tab

The exp-normal distribution is infinitely divisible

OpenAIRE

Pinelis, Iosif

2018-01-01

Let $Z$ be a standard normal random variable (r.v.). It is shown that the distribution of the r.v. $\\ln|Z|$ is infinitely divisible; equivalently, the standard normal distribution considered as the distribution on the multiplicative group over $\\mathbb{R}\\setminus\\{0\\}$ is infinitely divisible.

Division V: Commission 42: Close Binaries

Science.gov (United States)

Ribas, Ignasi; Richards, Mercedes T.; Rucinski, Slavek; Bradstreet, David H.; Harmanec, Petr; Kaluzny, Janusz; Mikolajewska, Joanna; Munari, Ulisse; Niarchos, Panagiotis; Olah, Katalin; Pribulla, Theodor; Scarfe, Colin D.; Torres, Guillermo

2015-08-01

Commission 42 (C42) co-organized, together with Commission 27 (C27) and Division V (Div V) as a whole, a full day of science and business sessions that were held on 24 August 2012. The program included time slots for discussion of business matters related to Div V, C27 and C42, and two sessions of 2 hours each devoted to science talks of interest to both C42 and C27. In addition, we had a joint session between Div IV and Div V motivated by the proposal to reformulate the division structure of the IAU and the possible merger of the two divisions into a new Div G. The current report gives an account of the matters discussed during the business session of C42.

Chemical Technology Division annual technical report, 1990

International Nuclear Information System (INIS)

1991-05-01

Highlights of the Chemical Technology (CMT) Division's activities during 1990 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for coal- fired magnetohydrodynamics and fluidized-bed combustion; (3) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for a high-level waste repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams, concentrating plutonium solids in pyrochemical residues by aqueous biphase extraction, and treating natural and process waters contaminated by volatile organic compounds; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the scientific and engineering programs at Argonne National Laboratory (ANL). 66 refs., 69 figs., 6 tabs

Chemical Technology Division annual technical report, 1990

Energy Technology Data Exchange (ETDEWEB)

1991-05-01

Highlights of the Chemical Technology (CMT) Division's activities during 1990 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for coal- fired magnetohydrodynamics and fluidized-bed combustion; (3) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for a high-level waste repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams, concentrating plutonium solids in pyrochemical residues by aqueous biphase extraction, and treating natural and process waters contaminated by volatile organic compounds; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the scientific and engineering programs at Argonne National Laboratory (ANL). 66 refs., 69 figs., 6 tabs.

Theoretical Division annual report, FY 1975. [LASL

Energy Technology Data Exchange (ETDEWEB)

Carruthers, P.A.

1976-02-01

This report presents an overview of the activities in the Theoretical Division and a summary of research highlights during FY 1975. It is intended to inform a wide audience about the theoretical work of the LASL and, therefore, contains introductory material which places recent advances in a broader context. The report is organized into two special interest reports: reactor safety research and the Advanced Research Committee, and 11 reports from the T-Division group leaders on the work of their respective groups. Main interests and responsibilities are outlined including the relationship of the group's work to the work of other T-Division groups and other divisions at the Laboratory. The description of research highlights for FY 1975 explains in a fairly simple, straightforward manner the major recent advances and their significance. Each group report is followed by a publication list for FY 1975 (330 references) and a list of talks given outside the Laboratory (140 references). 29 figures. (auth)

Development and Testing of the Healthy Work Environment Inventory: A Reliable Tool for Assessing Work Environment Health and Satisfaction.

Science.gov (United States)

Clark, Cynthia M; Sattler, Victoria P; Barbosa-Leiker, Celestina

2016-10-01

Fostering healthy work environments that enhance job satisfaction and reflect high levels of employee engagement and productivity is imperative for all organizations. This is especially true for health care organizations where unhealthy work conditions can lead to poor patient outcomes. A convenience sample of 520 nursing faculty and practice-based nurses in the United States participated in a study to test the psychometric properties of the Healthy Work Environment Inventory (HWEI). A factor analysis and other reliability analyses support the use of the HWEI as a valid and reliable instrument to measure perceptions of work environment health. The HWEI is a 20-item psychometrically sound instrument to measure perceptions of the health of the work environment. It may be completed either as an individual exercise or by all members of a team to compare perceptions of work environment health, to determine areas of strength and improvement, and to form the basis for interviewing. [J Nurs Educ. 2016;55(10):555-562.]. Copyright 2016, SLACK Incorporated.

76 FR 59769 - Clarification on the Division 1.1 Fireworks Approvals Policy

Science.gov (United States)

2011-09-27

... issuing the EX approval. While APA Standard 87-1 references two instances where Division 1.1 fireworks may... test laboratory if the firework device is manufactured in accordance with APA Standard 87-1 (IBR, see... certify that the firework device conforms to the APA Standard 87-1 and that the descriptions and technical...

A novel model of magnetorheological damper with hysteresis division

Science.gov (United States)

Yu, Jianqiang; Dong, Xiaomin; Zhang, Zonglun

2017-10-01

Due to the complex nonlinearity of magnetorheological (MR) behavior, the modeling of MR dampers is a challenge. A simple and effective model of MR damper remains a work in progress. A novel model of MR damper is proposed with force-velocity hysteresis division method in this study. A typical hysteresis loop of MR damper can be simply divided into two novel curves with the division idea. One is the backbone curve and the other is the branch curve. The exponential-family functions which capturing the characteristics of the two curves can simplify the model and improve the identification efficiency. To illustrate and validate the novel phenomenological model with hysteresis division idea, a dual-end MR damper is designed and tested. Based on the experimental data, the characteristics of the novel curves are investigated. To simplify the parameters identification and obtain the reversibility, the maximum force part, the non-dimensional backbone part and the non-dimensional branch part are derived from the two curves. The maximum force part and the non-dimensional part are in multiplication type add-rule. The maximum force part is dependent on the current and maximum velocity. The non-dominated sorting genetic algorithm II (NSGA II) based on the design of experiments (DOE) is employed to identify the parameters of the normalized shape functions. Comparative analysis is conducted based on the identification results. The analysis shows that the novel model with few identification parameters has higher accuracy and better predictive ability.

Nuclear Science Division, 1995--1996 annual report

International Nuclear Information System (INIS)

Poskanzer, A.M.

1997-02-01

This report describes the activities of the Nuclear Science Division (NSD) for the two-year period, January 1, 1995 to January 1, 1997. This was a time of major accomplishments for all research programs in the Division-many of which are highlighted in the reports of this document

Nuclear Science Division, 1995--1996 annual report

Energy Technology Data Exchange (ETDEWEB)

Poskanzer, A.M. [ed.

1997-02-01

This report describes the activities of the Nuclear Science Division (NSD) for the two-year period, January 1, 1995 to January 1, 1997. This was a time of major accomplishments for all research programs in the Division-many of which are highlighted in the reports of this document.

A Study of Mars Dust Environment Simulation at NASA Johnson Space Center Energy Systems Test Area Resource Conversion Test Facility

Science.gov (United States)

Chen, Yuan-Liang Albert

1999-01-01

The dust environment on Mars is planned to be simulated in a 20 foot thermal-vacuum chamber at the Johnson Space Center, Energy Systems Test Area Resource Conversion Test Facility in Houston, Texas. This vacuum chamber will be used to perform tests and study the interactions between the dust in Martian air and ISPP hardware. This project is to research, theorize, quantify, and document the Mars dust/wind environment needed for the 20 foot simulation chamber. This simulation work is to support the safety, endurance, and cost reduction of the hardware for the future missions. The Martian dust environment conditions is discussed. Two issues of Martian dust, (1) Dust Contamination related hazards, and (2) Dust Charging caused electrical hazards, are of our interest. The different methods of dust particles measurement are given. The design trade off and feasibility were studied. A glass bell jar system is used to evaluate various concepts for the Mars dust/wind environment simulation. It was observed that the external dust source injection is the best method to introduce the dust into the simulation system. The dust concentration of 30 Mg/M3 should be employed for preparing for the worst possible Martian atmosphere condition in the future. Two approaches thermal-panel shroud for the hardware conditioning are discussed. It is suggested the wind tunnel approach be used to study the dust charging characteristics then to be apply to the close-system cyclone approach. For the operation cost reduction purpose, a dehumidified ambient air could be used to replace the expensive CO2 mixture for some tests.

Earth Sciences Division, collected abstracts, 1978

International Nuclear Information System (INIS)

Taasevigen, D.K.; Henry, A.L.; Madsen, S.K.

1979-01-01

Abstracts of papers, internal reports, and talks presented during 1978 at national and international meetings by members of the Earth Sciences Division of the Lawrence Livermore Laboratory are compiled. The arrangement is alphabetical (by author). For any given report, a bibliographic reference appears under the name of each coauthor. A topical index at the end provides useful cross references, while indicating major areas of research interest in the Earth Sciences Division

Weapons Experiments Division Explosives Operations Overview

Energy Technology Data Exchange (ETDEWEB)

Laintz, Kenneth E. [Los Alamos National Laboratory

2012-06-19

Presentation covers WX Division programmatic operations with a focus on JOWOG-9 interests. A brief look at DARHT is followed by a high level overview of explosives research activities currently being conducted within in the experimental groups of WX-Division. Presentation covers more emphasis of activities and facilities at TA-9 as these efforts have been more traditionally aligned with ongoing collaborative explosive exchanges covered under JOWOG-9.

Research into fisheries and the marine environment 1989-90

International Nuclear Information System (INIS)

1992-01-01

This biannual report includes notes on the work of the Aquatic Environment Protection Division of the Directorate of Fisheries Research, Lowestoft in relation to assessment and monitoring of radioactive waste disposal and research into the environmental behaviour of radionuclides. (UK)

Laser and Plasma Technology Division annual report 1993

International Nuclear Information System (INIS)

Venkatramani, N.; Verma, R.L.

1994-01-01

This report describes the activities of the Laser and Plasma Technology Division during the year 1993. This Division is engaged in the research and development of high power beams namely laser, plasma and electron beams, which are characterized by high power density, normally in excess of 1 kW/mm 2 . Laser and Plasma Technology Division has strived to establish indigenous capability to cater to the requirements of the Department of Atomic Energy. The broad programme objectives of the Division are : (1) Development and technology readiness studies of laser, plasma and electron beam devices, (2) Studies on related physical phenomena with a view to gain better understanding of the devices, and (3) Improvements in technology and exploration of new areas. This report covers the activities of the Division during 1993 and describes how successfully the objectives have been met. The activities described in the report are diverse in nature. The report has been compiled from individual reports of various groups/sections with marginal editing. (author). refs., tabs., figs

Laser and Plasma Technology Division annual report 1993

Energy Technology Data Exchange (ETDEWEB)

Venkatramani, N; Verma, R L [eds.; Bhabha Atomic Research Centre, Bombay (India). Laser and Plasma Technology Div.

1994-12-31

This report describes the activities of the Laser and Plasma Technology Division during the year 1993. This Division is engaged in the research and development of high power beams namely laser, plasma and electron beams, which are characterized by high power density, normally in excess of 1 kW/mm{sup 2}. Laser and Plasma Technology Division has strived to establish indigenous capability to cater to the requirements of the Department of Atomic Energy. The broad programme objectives of the Division are : (1) Development and technology readiness studies of laser, plasma and electron beam devices, (2) Studies on related physical phenomena with a view to gain better understanding of the devices, and (3) Improvements in technology and exploration of new areas. This report covers the activities of the Division during 1993 and describes how successfully the objectives have been met. The activities described in the report are diverse in nature. The report has been compiled from individual reports of various groups/sections with marginal editing. (author). refs., tabs., figs.

Instructional designing the STEM education model for fostering creative thinking abilities in physics laboratory environment classes

Science.gov (United States)

Chanthala, Chumpon; Santiboon, Toansakul; Ponkham, Kamon

2018-01-01

To investigate the effects of students' activity-based on learning approaching management through the STEM Education Instructional Model for fostering their creative thinking abilities of their learning achievements in physics laboratory classroom environments with the sample size consisted of 48 students at the 10th grade level in two classes in Mahasarakham University Demonstration School(Secondary Division) in Thailand. Students' creative thinking abilities were assessed with the with the 24-item GuilfordCreative Thinking Questionnaire (GCTQ). Students' perceptions of their physics classroom learning environments were obtained using the 35-item Physics Laboratory Environment Inventory (PLEI). Associations between students' learning achievements of their post-test assessment indicated that 26% of the coefficient predictive value (R2) of the variance in students' creative thinking abilities was attributable to their perceptions for the GCTQ. Students' learning outcomes of their post-test assessment, the R2value indicated that 35% of the variances for the PLEI, the R2value indicated that 63% of the variances for their creative thinking abilities were attributable to theiraffecting the activity-based on learning for fostering their creative thinking are provided.

Stigma associated with sexually transmissible infection testing in an online testing environment: examining the perspectives of youth in Vancouver, Canada.

Science.gov (United States)

Karamouzian, Mohammad; Knight, Rod; Davis, Wendy M; Gilbert, Mark; Shoveller, Jean

2018-02-01

Background Online sexually transmissible infection (STI) testing is increasingly available and has shown promising results across different settings. However, evidence on how stigma associated with STI testing may be experienced by youth in the context of these online services is limited. A convenience sample of 71 youth (aged 15-24 years) both male and female was engaged through online and offline recruitment strategies in Vancouver, Canada. Through semistructured and exploratory interviews, participants were asked about their perceptions of stigma associated with STI testing in an online testing environment. Data were analysed using a thematic analysis approach. Youth came from a diverse set of sociodemographic backgrounds and most (n=46, 65%) had previously accessed STI testing in clinic-based settings. Participants' perceptions pointed to the benefits of online testing for reducing the external stigma despite the potential persistence of internalised stigma. Notions of hegemonic masculinity and emphasised femininity were also present in the participants' descriptions of the role of gender in accessing online STI testing. Online STI testing could potentially ameliorate the experiences of participants in regards to the stigma associated with STI testing; however, participants' internalised feelings of shame and stigma around testing for STI may continue to persist. Our findings underscore the need to revisit and re-evaluate existing STI testing services to provide less anxiety-inducing testing environments for youth.

Quantum key distribution for 10 Gb/s dense wavelength division multiplexing networks

International Nuclear Information System (INIS)

Patel, K. A.; Dynes, J. F.; Lucamarini, M.; Choi, I.; Sharpe, A. W.; Yuan, Z. L.; Shields, A. J.; Penty, R. V.

2014-01-01

We demonstrate quantum key distribution (QKD) with bidirectional 10 Gb/s classical data channels in a single fiber using dense wavelength division multiplexing. Record secure key rates of 2.38 Mbps and fiber distances up to 70 km are achieved. Data channels are simultaneously monitored for error-free operation. The robustness of QKD is further demonstrated with a secure key rate of 445 kbps over 25 km, obtained in the presence of data lasers launching conventional 0 dBm power. We discuss the fundamental limit for the QKD performance in the multiplexing environment

Plutonium in the desert environment of the Nevada Test Site and the Tonopah Test Range

International Nuclear Information System (INIS)

Romney, E.M.; Essington, E.H.; Fowler, E.B.; Tamura, T.; Gilbert, R.O.

1987-01-01

Several safety shot tests were conducted in the desert environment of the Nevada Test Site and the Tonopah Test Range during the period 1955 to 1963. Follow-up studies were conducted in fallout areas resulting from these tests to investigate the distribution in soils and the availability to animals and plants of plutonium (and americium) after residence times of 10 to 20 years. Soil profile studies disclosed that more than 95% of the plutonium (and americium) dispersed as fallout to the environment had remained in the top 5 cm of soil in undisturbed areas. Significant amounts had been redistributed into blow-sand mounds formed underneath clumps of vegetation. That redistribution should be expected because the contaminant was associated primarily with the coarse silt and fine sand particle size fractions. Resuspension factors were calculated that varied from 9.1 x 10 -11 m -1 to 5.4 x 10 -9 m -1 with geometric mean and arithmetic averages of 2.9 x 10 -10 m -1 and 6.8 x 10 -10 m -1 , respectively; however, the plutonium essentially remained in place when the soil surface was left undisturbed. Vegetation in the fallout areas was contaminated primarily by resuspendable material deposited on the surface of plant foliage; plutonium concentration ratios ranged from 10 -3 to 10 0 . Carcass samples of small vertebrate animals collected from fallout areas contained only trace amounts of plutonium compared to the environmental exposure levels. Furthermore, only trace amounts of plutonium (and americium) were found in muscle and organ tissues of grazing cattle during a 3-year on-site residence experiment. 36 references, 4 figures

DNR Division of Parks and Trails District Boundaries

Data.gov (United States)

Minnesota Department of Natural Resources — This data shows the DNR Division of Parks and Trails District Boundaries as of May 2010. The boundaries were created by the Division Leadership Team. Boundaries are...

Solid State Division

International Nuclear Information System (INIS)

Green, P.H.; Watson, D.M.

1989-08-01

This report contains brief discussions on work done in the Solid State Division of Oak Ridge National Laboratory. The topics covered are: Theoretical Solid State Physics; Neutron scattering; Physical properties of materials; The synthesis and characterization of materials; Ion beam and laser processing; and Structure of solids and surfaces

Marriage, Specialization, and the Gender Division of Labor

OpenAIRE

Matthew J. Baker; Joyce P. Jacobsen

2005-01-01

A customary gender division of labor is one in which women and men are directed towards certain tasks and/or explicitly prohibited from performing others. We offer an explanation as to why the gender division of labor is so often enforced by custom, and why customary gender divisions of labor generally involve both direction and prohibition. Our model builds on the literature on the marital hold-up problem, and considers both problems in choice of specialty and human capital acquisition in a ...

Fuel Chemistry Division: progress report for 1985

International Nuclear Information System (INIS)

1988-01-01

Fuel Chemistry Division was formed in May 1985 to give a larger emphasis on the research and development in chemistry of the nuclear fuel cycle. The areas of research in Fuel Chemistry Division are fuel development and its chemical quality control, understanding of the fuel behaviour and post irradiation examinations, chemistry of reprocessing and waste management processes as also the basic aspects of actinide and relevant fission product elements. This report summarises the work by the staff of the Division during 1985 and also some work from the previous periods which was not reported in the progress reports of the Radiochemistry Division. The work related to the FBTR fuel was one of the highlights during this period. In the area of process chemistry useful work has been carried out for processing of plutonium bearing solutions. In the area of mass spectrometry, the determination of trace constituents by spark source mass spectrometry has been a major area of research. Significant progress has also been made in the use of alpha spectromet ry techniques for the determination of plutonium in dissolver solution and other samples. The technology of plutonium utilisation is quite complex and the Division would continue to look into the chemical aspects of this technology and provide the necessary base for future developments in this area. (author)

75 FR 45154 - National Security Division; Agency Information Collection Activities:

Science.gov (United States)

2010-08-02

... DEPARTMENT OF JUSTICE [OMB Number 1124-0003] National Security Division; Agency Information...), National Security Division (NSD), will be submitting the following information collection request to the..., 10th & Constitution Avenue, NW., National Security Division, Counterespionage Section/Registration Unit...

Lifespan and reproduction of isoclonal individual E.coli in different environments

DEFF Research Database (Denmark)

Jouvet, Lionel; Steiner, Ulrich

Lifespan and reproduction are key fitness components, both of which are influences by genetics and the environment. Tracking large numbers of genotypically known individuals throughout their lives in known environments has been challenging. Here we show for isogenic individual E. coli bacteria...... under controlled environments how demographic parameters and distributions in reproduction and survival change across environments. We achieve this by using a microfluidic device that traps thousands of individual E. coli cells and tracks their division (reproduction) over their lifespan. Our results...

2003 Chemical Engineering Division annual technical report

International Nuclear Information System (INIS)

Lewis, D.; Graziano, D.; Miller, J. F.; Vandegrift, G.

2004-01-01

The Chemical Engineering Division is one of six divisions within the Engineering Research Directorate at Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, to promote national security, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. The Division is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Additionally, the Division operates the Analytical Chemistry Laboratory, which provides a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training in chemistry; physics; materials science; and electrical, mechanical, chemical, and nuclear engineering. They are specialists in electrochemistry, ceramics, metallurgy, catalysis, materials characterization, nuclear magnetic resonance, repository science, and the nuclear fuel cycle. Our staff have experience working in and collaborating with university, industry and government research and development laboratories throughout the world. Our wide-ranging expertise finds ready application in solving energy, national security, and environmental problems. Division personnel are frequently called on by governmental and industrial organizations for advice and contributions to problem solving in areas that intersect present and past Division programs and activities. Currently, we are engaged in the development of several technologies of

USB environment measurements based on full-scale static engine ground tests

Science.gov (United States)

Sussman, M. B.; Harkonen, D. L.; Reed, J. B.

1976-01-01

Flow turning parameters, static pressures, surface temperatures, surface fluctuating pressures and acceleration levels were measured in the environment of a full-scale upper surface blowing (USB) propulsive lift test configuration. The test components included a flightworthy CF6-50D engine, nacelle, and USB flap assembly utilized in conjunction with ground verification testing of the USAF YC-14 Advanced Medium STOL Transport propulsion system. Results, based on a preliminary analysis of the data, generally show reasonable agreement with predicted levels based on model data. However, additional detailed analysis is required to confirm the preliminary evaluation, to help delineate certain discrepancies with model data, and to establish a basis for future flight test comparisons.

Nuclear Physics Division annual report 1992

International Nuclear Information System (INIS)

Betigeri, M.G.

1993-01-01

The report covers the research and development activities of the Nuclear Physics Division for the period January to December 1992. These research and development activities are reported under the headings: 1) Experiments, 2) Theory, 3) Applications, 4) Instrumentation, and 5) The Pelletron Accelerator. At the end a list of publications by the staff scientists of the Division is given. Colloquia and seminars held during the year are also listed. (author). refs., tabs., figs

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

Hirota, Jitsuya; Asaoka, Takumi; Suzuki, Tomoo; Mitani, Hiroshi; Akino, Fujiyoshi

1977-09-01

Research activities in the Division of Reactor Engineering in fiscal 1976 are described. Works of the division concern mainly the development of multi-purpose Very High Temperature Gas Cooled Reactor, fusion reactor engineering, and the development of Liquid Metal Fast Breeder Reactor in Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology, and activities of the Committee on Reactor Physics. (auth.)

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1976-09-01

Research activities conducted in Reactor Engineering Division in fiscal 1975 are summarized in this report. Works in the division are closely related to the development of multi-purpose High-temperature Gas Cooled Reactor, the development of Liquid Metal Fast Breeder Reactor by Power Reactor and Nuclear Fuel Development Corporation, and engineering research of thermonuclear fusion reactor. Many achievements are described concerning nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology and activities of the Committee on Reactor Physics. (auth.)

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1975-11-01

Research activities in fiscal 1974 in Reactor Engineering Division of eight laboratories and computing center are described. Works in the division are closely related with the development of a multi-purpose High-temperature Gas Cooled Reactor, the development of a Liquid Metal Fast Breeder Reactor in Power Reactor and Nuclear Fuel Development Corporation, and engineering of thermonuclear fusion reactors. They cover nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology and aspects of the computing center. (auth.)

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

Matsuura, Shojiro; Nakahara, Yasuaki; Takano, Hideki

1982-09-01

Research and development activities in the Division of Reactor Engineering in fiscal 1981 are described. The work of the Division is closely related to development of multipurpose Very High Temperature Gas Cooled Reactor and fusion reactor, and development of Liquid Metal Fast Breeder Reactor carried out by Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are achievements in fields such as nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, reactor and nuclear instrumentation, reactor control and diagnosis, and fusion reactor technology, and activities of the Committee on Reactor Physics. (author)

Determination of cell division axes in the early embryogenesis of Caenorhabditis elegans

OpenAIRE

1987-01-01

The establishment of cell division axes was examined in the early embryonic divisions of Caenorhabditis elegans. It has been shown previously that there are two different patterns of cleavage during early embryogenesis. In one set of cells, which undergo predominantly determinative divisions, the division axes are established successively in the same orientation, while division axes in the other set, which divide mainly proliferatively, have an orthogonal pattern of division. We have investig...

History of Division 29, 1993-2013: another 20 years of psychotherapy.

Science.gov (United States)

Williams, Elizabeth Nutt; Barnett, Jeffrey E; Canter, Mathilda B

2013-03-01

The history of Division 29 (Psychotherapy) of the American Psychological Association (APA) from 1993 to 2013 is reviewed. The 20 years of history can be traced via the Division's primary publications (the journal Psychotherapy and its newsletter Psychotherapy Bulletin) as well as the history of those who have served leadership roles in the Division and have won Divisional awards. Several recurring themes emerge related to the Division's articulations of its own identity, the Division's advocacy efforts vis-à-vis the profession and the APA, and the work of the Division on behalf of major social issues (such as disaster relief and the nation's health care).

Solid State Division

Energy Technology Data Exchange (ETDEWEB)

Green, P.H.; Watson, D.M. (eds.)

1989-08-01

This report contains brief discussions on work done in the Solid State Division of Oak Ridge National Laboratory. The topics covered are: Theoretical Solid State Physics; Neutron scattering; Physical properties of materials; The synthesis and characterization of materials; Ion beam and laser processing; and Structure of solids and surfaces. (LSP)

A connection between free and classical infinite divisibility

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole Eiler; Thorbjørnsen, Steen

2004-01-01

In this paper we continue our studies, initiated in Refs. 2–4, of the connections between the classes of infinitely divisible probability measures in classical and in free probability. We show that the free cumulant transform of any freely infinitely divisible probability measure equals...... the classical cumulant transform of a certain classically infinitely divisible probability measure, and we give several characterizations of the latter measure, including an interpretation in terms of stochastic integration. We find, furthermore, an alternative definition of the Bercovici–Pata bijection, which...

Operational computer graphics in the flight dynamics environment

Science.gov (United States)

Jeletic, James F.

1989-01-01

Over the past five years, the Flight Dynamics Division of the National Aeronautics and Space Administration's (NASA's) Goddard Space Flight Center has incorporated computer graphics technology into its operational environment. In an attempt to increase the effectiveness and productivity of the Division, computer graphics software systems have been developed that display spacecraft tracking and telemetry data in 2-d and 3-d graphic formats that are more comprehensible than the alphanumeric tables of the past. These systems vary in functionality from real-time mission monitoring system, to mission planning utilities, to system development tools. Here, the capabilities and architecture of these systems are discussed.

Physics division annual report 2005

International Nuclear Information System (INIS)

Glover, J.

2007-01-01

This report highlights the research performed in 2005 in the Physics Division of Argonne National Laboratory. The Division's programs include operation of ATLAS as a national user facility, nuclear structure and reaction research, nuclear theory, medium energy nuclear research and accelerator research and development. The mission of Nuclear Physics is to understand the origin, evolution and structure of baryonic matter in the universe--the matter that makes up stars, planets and human life itself. The Division's research focuses on innovative new ways to address this mission and 2005 was a year of great progress. One of the most exciting developments is the initiation of the Californium Rare Ion Breeder Upgrade, CARIBU. By combining a Cf-252 fission source, the gas catcher technology developed for rare isotope beams, a high-resolution isobar separator, and charge breeding ECR technology, CARIBU will make hundreds of new neutron-rich isotope beams available for research. The cover illustration shows the anticipated intensities of low-energy beams that become available for low-energy experiments and for injection into ATLAS for reacceleration. CARIBU will be completed in early 2009 and provide us with considerable experience in many of the technologies developed for a future high intensity exotic beam facility. Notable results in research at ATLAS include a measurement of the isomeric states in 252 No that helps pin down the single particle structure expected for superheavy elements, and a new low-background measurement of 16 N beta-decay to determine the 12 C(α, γ) 16 O reaction rate that is so important in astrophysical environments. Precise mass measurements shed new light on the unitarity of the quark weak-mixing matrix in the search for physics beyond the standard model. ATLAS operated for 4686 hours of research in FY2005 while achieving 95% efficiency of beam delivery for experiments. In Medium-Energy Physics, radium isotopes were trapped in an atom trap for

Physics division annual report 2005.

Energy Technology Data Exchange (ETDEWEB)

Glover, J.; Physics

2007-03-12

This report highlights the research performed in 2005 in the Physics Division of Argonne National Laboratory. The Division's programs include operation of ATLAS as a national user facility, nuclear structure and reaction research, nuclear theory, medium energy nuclear research and accelerator research and development. The mission of Nuclear Physics is to understand the origin, evolution and structure of baryonic matter in the universe--the matter that makes up stars, planets and human life itself. The Division's research focuses on innovative new ways to address this mission and 2005 was a year of great progress. One of the most exciting developments is the initiation of the Californium Rare Ion Breeder Upgrade, CARIBU. By combining a Cf-252 fission source, the gas catcher technology developed for rare isotope beams, a high-resolution isobar separator, and charge breeding ECR technology, CARIBU will make hundreds of new neutron-rich isotope beams available for research. The cover illustration shows the anticipated intensities of low-energy beams that become available for low-energy experiments and for injection into ATLAS for reacceleration. CARIBU will be completed in early 2009 and provide us with considerable experience in many of the technologies developed for a future high intensity exotic beam facility. Notable results in research at ATLAS include a measurement of the isomeric states in {sup 252}No that helps pin down the single particle structure expected for superheavy elements, and a new low-background measurement of {sup 16}N beta-decay to determine the {sup 12}C({alpha},{gamma}){sup 16}O reaction rate that is so important in astrophysical environments. Precise mass measurements shed new light on the unitarity of the quark weak-mixing matrix in the search for physics beyond the standard model. ATLAS operated for 4686 hours of research in FY2005 while achieving 95% efficiency of beam delivery for experiments. In Medium-Energy Physics, radium

Standard test method for determining a threshold stress intensity factor for environment-assisted cracking of metallic materials

CERN Document Server

American Society for Testing and Materials. Philadelphia

2003-01-01

1.1 This test method covers the determination of the environment-assisted cracking threshold stress intensity factor parameters, KIEAC and KEAC, for metallic materials from constant-force testing of fatigue precracked beam or compact fracture specimens and from constant-displacement testing of fatigue precracked bolt-load compact fracture specimens. 1.2 This test method is applicable to environment-assisted cracking in aqueous or other aggressive environments. 1.3 Materials that can be tested by this test method are not limited by thickness or by strength as long as specimens are of sufficient thickness and planar size to meet the size requirements of this test method. 1.4 A range of specimen sizes with proportional planar dimensions is provided, but size may be variable and adjusted for yield strength and applied force. Specimen thickness is a variable independent of planar size. 1.5 Specimen configurations other than those contained in this test method may be used, provided that well-established stress ...

A combination test for detection of gene-environment interaction in cohort studies.

Science.gov (United States)

Coombes, Brandon; Basu, Saonli; McGue, Matt

2017-07-01

Identifying gene-environment (G-E) interactions can contribute to a better understanding of disease etiology, which may help researchers develop disease prevention strategies and interventions. One big criticism of studying G-E interaction is the lack of power due to sample size. Studies often restrict the interaction search to the top few hundred hits from a genome-wide association study or focus on potential candidate genes. In this paper, we test interactions between a candidate gene and an environmental factor to improve power by analyzing multiple variants within a gene. We extend recently developed score statistic based genetic association testing approaches to the G-E interaction testing problem. We also propose tests for interaction using gene-based summary measures that pool variants together. Although it has recently been shown that these summary measures can be biased and may lead to inflated type I error, we show that under several realistic scenarios, we can still provide valid tests of interaction. These tests use significantly less degrees of freedom and thus can have much higher power to detect interaction. Additionally, we demonstrate that the iSeq-aSum-min test, which combines a gene-based summary measure test, iSeq-aSum-G, and an interaction-based summary measure test, iSeq-aSum-I, provides a powerful alternative to test G-E interaction. We demonstrate the performance of these approaches using simulation studies and illustrate their performance to study interaction between the SNPs in several candidate genes and family climate environment on alcohol consumption using the Minnesota Center for Twin and Family Research dataset. © 2017 WILEY PERIODICALS, INC.

New grid based test bed environment for carrying out ad-hoc networking experiments

CSIR Research Space (South Africa)

Johnson, D

2006-09-01

Full Text Available and the third is to do analysis on a real test bed network which has implemented the ad-hoc networking protocol. This paper concerns the third option. Most researchers who have done work on test bed environments have used either indoor Wifi inter-office links...

Does rational selection of training and test sets improve the outcome of QSAR modeling?

Science.gov (United States)

Martin, Todd M; Harten, Paul; Young, Douglas M; Muratov, Eugene N; Golbraikh, Alexander; Zhu, Hao; Tropsha, Alexander

2012-10-22

Prior to using a quantitative structure activity relationship (QSAR) model for external predictions, its predictive power should be established and validated. In the absence of a true external data set, the best way to validate the predictive ability of a model is to perform its statistical external validation. In statistical external validation, the overall data set is divided into training and test sets. Commonly, this splitting is performed using random division. Rational splitting methods can divide data sets into training and test sets in an intelligent fashion. The purpose of this study was to determine whether rational division methods lead to more predictive models compared to random division. A special data splitting procedure was used to facilitate the comparison between random and rational division methods. For each toxicity end point, the overall data set was divided into a modeling set (80% of the overall set) and an external evaluation set (20% of the overall set) using random division. The modeling set was then subdivided into a training set (80% of the modeling set) and a test set (20% of the modeling set) using rational division methods and by using random division. The Kennard-Stone, minimal test set dissimilarity, and sphere exclusion algorithms were used as the rational division methods. The hierarchical clustering, random forest, and k-nearest neighbor (kNN) methods were used to develop QSAR models based on the training sets. For kNN QSAR, multiple training and test sets were generated, and multiple QSAR models were built. The results of this study indicate that models based on rational division methods generate better statistical results for the test sets than models based on random division, but the predictive power of both types of models are comparable.

Organizational commitment among intercollegiate head athletic trainers: examining our work environment.

Science.gov (United States)

Winterstein, A P

1998-01-01

To 1) examine the commitment of head athletic trainers to their intercollegiate work environments, 2) develop a model that better reflects the head athletic trainer's daily work setting, and 3) use new techniques to describe the various ways head athletic trainers demonstrate commitment to their organizations. Organizational commitment (OC) surveys were sent to 461 head athletic trainers identified for the sample. A response rate of 71.5% (330/461) was obtained from the mail survey. A proportional random sample of head athletic trainers was taken from a population identified in the National Association of Collegiate Directors of Athletics (NACDA) directory of intercollegiate athletics as Division I, II, and III institutions. Returned OC surveys were analyzed using descriptive and inferential statistics for all demographic and OC variables. Exploratory cluster analysis was performed to examine naturally clustering groups. Exploratory cluster analysis revealed five naturally clustering groups that represent the head athletic trainers' patterns of commitment across the specific organizational targets. Paired t tests indicated that the continuance commitment scores were significantly lower than the affective and normative scores across the sample. Analysis of variance tests indicated significant differences for specific commitment dimensions based on gender and NCAA division demographics. Beyond that, the five-cluster solution revealed no particular demographic characteristics that predisposed individuals to specific clusters. THE FINDINGS REINFORCE A CENTRAL THEME IN INTERCOLLEGIATE ATHLETIC TRAINING: that student-athletes and student athletic trainers are the primary focus of the head athletic trainers' commitment. Positive attachment and obligation directed toward student-athletes and student athletic trainers link the five clusters. Commitment patterns in areas other than student-athletes and student athletic trainers define the cluster membership or head athletic

UAS-NAS Integrated Human in the Loop: Test Environment Report

Science.gov (United States)

Murphy, Jim; Otto, Neil; Jovic, Srba

2015-01-01

The desire and ability to fly Unmanned Aircraft Systems (UAS) in the National Airspace System (NAS) is of increasing urgency. The application of unmanned aircraft to perform national security, defense, scientific, and emergency management are driving the critical need for less restrictive access by UAS to the NAS. UAS represent a new capability that will provide a variety of services in the government (public) and commercial (civil) aviation sectors. The growth of this potential industry has not yet been realized due to the lack of a common understanding of what is required to safely operate UAS in the NAS. NASA's UAS Integration in the NAS Project is conducting research in the areas of Separation Assurance/Sense and Avoid Interoperability (SSI), Human Systems Integration (HSI), and Communication to support reducing the barriers of UAS access to the NAS. This research was broken into two research themes namely, UAS Integration and Test Infrastructure. UAS Integration focuses on airspace integration procedures and performance standards to enable UAS integration in the air transportation system, covering Sense and Avoid (SAA) performance standards, command and control performance standards, and human systems integration. The focus of the Test Infrastructure theme was to enable development and validation of airspace integration procedures and performance standards, including the execution of integrated test and evaluation. In support of the integrated test and evaluation efforts, the Project developed an adaptable, scalable, and schedulable relevant test environment incorporating live, virtual, and constructive elements capable of validating concepts and technologies for unmanned aircraft systems to safely operate in the NAS. To accomplish this task, the Project planned to conduct three integrated events: a Human-in-the-Loop simulation and two Flight Test series that integrated key concepts, technologies and/or procedures in a relevant air traffic environment. Each of

Onset of cell division in maize germination: action of auxins

International Nuclear Information System (INIS)

de Jimenez, E.S.; Baiza, A.; Aguilar, R.

1987-01-01

Seed germination implies metabolic reactivation, synthesis of macromolecules and onset of cell division. During maize germination, meristematic tissues of embryos re-initiate cell division asynchronically. Since auxins are known to stimulate cell division, they asked how auxins might regulate cell cycle re-initiation. Embryonic tissues were incubated with and without auxins. A pulse of either 3 H-thymidine or 32 P-ortophosphate was given to the tissues. Mitotic indexes were determined and % of labeled mitotic cells recorded. Results indicated that meristematic cells re-initiate cell division either from G 1 or G 2 phases. Auxin stimulated differentially the cell division process of these cells. 32 P incorporation into cytoplasmic or nucleic histones was measured. Auxins stimulated this incorporation. Active turnover of histone phosphorylation occurred simultaneously to the cell division process. It is suggested that auxins might regulate the cell cycle by phosphorylation-dephosphorylation of histones

Organization structure. Main activities of the Division

International Nuclear Information System (INIS)

2008-01-01

In this chapter the organization structure as well as main activities of the Division for radiation safety, NPP decommissioning and radioactive waste management are presented. This Division of the VUJE, a.s. consists of the following sections and departments: Section for economic and technical services; Section for radiation protection of employees; Department for management of emergency situations and risk assessment; Department for implementation of nuclear power facilities decommissioning and RAW management; Department for personnel and environmental dosimetry; Department for preparation of NPP decommissioning; Department for RAW treatment technologies; Department for chemical regimes and physico-chemical analyses; Department for management of nuclear power facilities decommissioning and RAW management. Main activities of this Division are presented.

ADP Analysis project for the Human Resources Management Division

Science.gov (United States)

Tureman, Robert L., Jr.

1993-01-01

The ADP (Automated Data Processing) Analysis Project was conducted for the Human Resources Management Division (HRMD) of NASA's Langley Research Center. The three major areas of work in the project were computer support, automated inventory analysis, and an ADP study for the Division. The goal of the computer support work was to determine automation needs of Division personnel and help them solve computing problems. The goal of automated inventory analysis was to find a way to analyze installed software and usage on a Macintosh. Finally, the ADP functional systems study for the Division was designed to assess future HRMD needs concerning ADP organization and activities.

Engineering Research Division publication report, calendar year 1980

International Nuclear Information System (INIS)

Miller, E.K.; Livingston, P.L.; Rae, D.C.

1980-06-01

Each year the Engineering Research Division of the Electronics Engineering Department at Lawrence Livermore Laboratory has issued an internal report listing all formal publications produced by the Division during the calendar year. Abstracts of 1980 reports are presented

Earth Sciences Division collected abstracts: 1980

Energy Technology Data Exchange (ETDEWEB)

Henry, A.L.; Hornady, B.F. (eds.)

1981-10-15

This report is a compilation of abstracts of papers, reports, and talks presented during 1980 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore National Laboratory. The arrangement is alphabetical (by author). For a given report, a bibliographic reference appears under the name of each coauthor, but the abstract itself is given only under the name of the first author (indicated in capital letters) or the first Earth Sciences Division author.

Nuclear Science Division: 1993 Annual report

International Nuclear Information System (INIS)

Myers, W.D.

1994-06-01

This report describes the activities of the Nuclear Science Division for the 1993 calendar year. This was another significant year in the history of the Division with many interesting and important accomplishments. Activities for the following programs are covered here: (1) nuclear structure and reactions program; (2) the Institute for Nuclear and Particle Astrophysics; (3) relativistic nuclear collisions program; (4) nuclear theory program; (5) nuclear data evaluation program, isotope project; and (6) 88-inch cyclotron operations

Nuclear Science Division: 1993 Annual report

Energy Technology Data Exchange (ETDEWEB)

Myers, W.D. [ed.

1994-06-01

This report describes the activities of the Nuclear Science Division for the 1993 calendar year. This was another significant year in the history of the Division with many interesting and important accomplishments. Activities for the following programs are covered here: (1) nuclear structure and reactions program; (2) the Institute for Nuclear and Particle Astrophysics; (3) relativistic nuclear collisions program; (4) nuclear theory program; (5) nuclear data evaluation program, isotope project; and (6) 88-inch cyclotron operations.

Earth Sciences Division annual report 1989

Energy Technology Data Exchange (ETDEWEB)

1990-06-01

This Annual Report presents summaries of selected representative research activities from Lawrence Berkeley Laboratory grouped according to the principal disciplines of the Earth Sciences Division: Reservoir Engineering and Hydrology, Geology and Geochemistry, and Geophysics and Geomechanics. We are proud to be able to bring you this report, which we hope will convey not only a description of the Division's scientific activities but also a sense of the enthusiasm and excitement present today in the Earth Sciences.

Earth Sciences Division collected abstracts: 1980

International Nuclear Information System (INIS)

Henry, A.L.; Hornady, B.F.

1981-01-01

This report is a compilation of abstracts of papers, reports, and talks presented during 1980 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore National Laboratory. The arrangement is alphabetical (by author). For a given report, a bibliographic reference appears under the name of each coauthor, but the abstract itself is given only under the name of the first author (indicated in capital letters) or the first Earth Sciences Division author

Radiochemistry Division annual progress report: 1988

International Nuclear Information System (INIS)

1990-01-01

The report covers the research and development (R and D) work carried out by Radiochemistry Division, Bhabha Atomic Research Centre, Bombay during the period 1987-1988. The R and D work is reported in the form of individual summari es grouped under the headings: (1)Actinide Chemistry, (2)Nuclear Chemistry, and (3)Spectroscopy. Some of the highlights of the work are studies on : (a)solvent extraction and complexation behaviour of actinides, (b)helium ion induced fission of 238 U and 165 Ho and fission yield of 252 Cf(sf), (c)separation of rare earths from fission products, (d)positron annihilation spectroscopy of high Tc superconductors, and (e)EPR spectroscopy of high Tc superconductors. Radioanalytical services and radiation sources given to the other Divisions and Organisations are listed. A list of publications and symposia papers by scientists of the Division is also given. 45 figs., 49 tabs

Engineering Physics Division progress report for period ending November 30, 1980

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

Separate abstracts are included for sections concerning measurement of nuclear cross sections and related quantities; nuclear cross-section evaluations and theory; nuclear cross-section processing, testing, and sensitivity analysis; engineering physics division integral experiments and their analyses; development of methods for shield and reactor analysis; analyses for specific systems or applications; energy model validation; systems reliability and operations research; and information analysis and distribution.

Engineering Physics Division progress report for period ending November 30, 1980

International Nuclear Information System (INIS)

1980-12-01

Separate abstracts are included for sections concerning measurement of nuclear cross sections and related quantities; nuclear cross-section evaluations and theory; nuclear cross-section processing, testing, and sensitivity analysis; engineering physics division integral experiments and their analyses; development of methods for shield and reactor analysis; analyses for specific systems or applications; energy model validation; systems reliability and operations research; and information analysis and distribution

H-Division quarterly report, April--June 1976

International Nuclear Information System (INIS)

1976-01-01

The purview of H-Division is the mechanics of fluids and solid bodies. Concise status reports of the projects undertaken by the various groups in the division are given. Representative topics studied include equations of state of various materials, fracture mechanics, penetration of armor by projectiles, turbulence generation, and the development of dynamics computer codes. 31 figures, 2 tables

Applied Chemistry Division progress report for the period 1990-1992

International Nuclear Information System (INIS)

Bharadwaj, S.R.; Kishore, K.; Ramshesh, V.

1993-01-01

The report covers the research and development (R and D) activities of the Applied Chemistry Division for the period January 1990 to December, 1992. R and D programmes of the Division are formulated to study the chemical aspects related to nuclear power plants and heavy water plants. The Division also gives consultancy to DAE units and outside agencies on water chemistry problems. The thrust areas of the Division's R and D programmes are : decontamination of nuclear facilities, metal water interaction of the materials used in PHT system, chemistry of soluble poisons, biofouling and its control in cooling water circuits, and treatment of cooling waters. Other major R and D activities are in the areas of: solid state reactions and high temperature thermodynamics, primary coolant water chemistry, speciation studies in metal amine systems, high temperature aqueous radiation chemistry. The Division was engaged in studies in novel areas such as dental implants, remote sealing of pipes in MS pipes, and cold fusion. The Division also designed and fabricated instruments like the Knudsen cell mass spectrometer, calorimeters and developed required software. All these R and D activities are reported in the form of individual summaries. A list of publications from the Division and a list of the staff members of the Division are given at the end of the report. (author). tabs., figs., appendices

Effect of gamma-irradiation and colchicine on cell division and differentiation of xylem elements in citrus limon juice vesicle cultures

International Nuclear Information System (INIS)

Khan, Aysha; Chauhan, Y.S.

1999-01-01

The effects of varying doses of gamma irradiation on cell division and cytodifferentiation of tracheary elements in cultured juice vesicles of Citrus limon (L) Burmann var. Assam lemon were investigated. Low radiation doses stimulated cell division and differentiation of xylem fibres, sclereids and tracheids in explants given up to 10 Gy of gamma rays. Although cell division and cytodifferentiation of fibers and sclereids occurred in explants exposed to 150 dose of Gy radiation, the intensity of differentiation was much less than that induced by 10 Gy radiation dose. Amongst the differential elements, tracheids were more sensitive to radiation than fibres and sclereids. The requirement of cell division for differentiation of xylem cells was also studied by using different concentrations of colchicine in Citrus limon juice vesicle cultures. It was found that the low concentrations of colchicine permitted normal cell division and also resulted in normal differentiation of xylem cells; higher colchicine concentration, however, inhibited cell division as well as differentiation and resulted in an abnormal differentiation of tracheary element. A positive correlation between intensity of nucleic acid staining and cell division in both the above-mentioned experiments was qualitatively confirmed by Azur B staining test of nucleic acid. Thus, it was concluded that juice vesicle parenchyma cells go through nucleic acid synthesis, followed by cell division before differentiation. (author)

Continuous Improvement in Battery Testing at the NASA/JSC Energy System Test Area

Science.gov (United States)

Boyd, William; Cook, Joseph

2003-01-01

The Energy Systems Test Area (ESTA) at the Lyndon B. Johnson Space Center in Houston, Texas conducts development and qualification tests to fulfill Energy System Division responsibilities relevant to ASA programs and projects. EST A has historically called upon a variety of fluid, mechanical, electrical, environmental, and data system capabilities spread amongst five full-service facilities to test human and human supported spacecraft in the areas of propulsion systems, fluid systems, pyrotechnics, power generation, and power distribution and control systems. Improvements at ESTA are being made in full earnest of offering NASA project offices an option to choose a thorough test regime that is balanced with cost and schedule constraints. In order to continue testing of enabling power-related technologies utilized by the Energy System Division, an especially proactive effort has been made to increase the cost effectiveness and schedule responsiveness for battery testing. This paper describes the continuous improvement in battery testing at the Energy Systems Test Area being made through consolidation, streamlining, and standardization.

Engineering Physics Division progress report for period ending November 30, 1978. [ORNL

Energy Technology Data Exchange (ETDEWEB)

Maienschein, F.C.

1979-01-01

Research and other activities of the Engineering Physics Division (formerly Neutron Physics Division) of ORNL during the period February 28, 1977 to November 30, 1978, are reported. The format is that of abstracts and summaries of prepared papers. Work is summarized in the following general areas: measurements of neutron cross sections and related quantities; cross-section theory, evaluations, and evaluation techniques; cross-section processing, testing, and sensitivity analyses; integral experiments and their analyses; development of methods for shield and reactor analyses; analyses for specific systems or applications (liquid-metal fast breeder reactor program, gas-cooled reactor program, alternate fuel cycle program, magnetic fusion energy program, high-energy physics program, accelerator breeding studies, miscellaneous studies); and information analysis and distribution. Overviews of each of these areas are included. (RWR)

Towers of generalized divisible quantum codes

Science.gov (United States)

Haah, Jeongwan

2018-04-01

A divisible binary classical code is one in which every code word has weight divisible by a fixed integer. If the divisor is 2ν for a positive integer ν , then one can construct a Calderbank-Shor-Steane (CSS) code, where X -stabilizer space is the divisible classical code, that admits a transversal gate in the ν th level of Clifford hierarchy. We consider a generalization of the divisibility by allowing a coefficient vector of odd integers with which every code word has zero dot product modulo the divisor. In this generalized sense, we construct a CSS code with divisor 2ν +1 and code distance d from any CSS code of code distance d and divisor 2ν where the transversal X is a nontrivial logical operator. The encoding rate of the new code is approximately d times smaller than that of the old code. In particular, for large d and ν ≥2 , our construction yields a CSS code of parameters [[O (dν -1) ,Ω (d ) ,d ] ] admitting a transversal gate at the ν th level of Clifford hierarchy. For our construction we introduce a conversion from magic state distillation protocols based on Clifford measurements to those based on codes with transversal T gates. Our tower contains, as a subclass, generalized triply even CSS codes that have appeared in so-called gauge fixing or code switching methods.

77 FR 48527 - National Customs Automation Program (NCAP) Test Concerning Automated Commercial Environment (ACE...

Science.gov (United States)

2012-08-14

... National Customs Automation Program (NCAP) test concerning the simplified entry functionality in the... DEPARTMENT OF HOMELAND SECURITY U.S. Customs and Border Protection National Customs Automation Program (NCAP) Test Concerning Automated Commercial Environment (ACE) Simplified Entry: Modification of...

Guillain Barre syndrome: the leading cause of acute flaccid paralysis in Hazara division.

Science.gov (United States)

Anis-ur-Rehman; Idris, Muhammad; Elahi, Manzoor; Jamshed; Arif, Adeel

2007-01-01

Acute flaccid paralysis (AFP) can be caused by a number of conditions. A common preventable cause is poliomyelitis which is still being reported in Pakistan, Guillain Barre Syndrome (GBS), also known as Acute Inflammatory Demyelinating Polyneuropathy, is another common cause of acute flaccid paralysis. It is important to recognize GBS in childhood as parents consider all acute flaccid paralysis to be due to poliomyelitis. The present study was designed to know the frequency of different causes of acute flaccid paralysis in Hazara division. This is a retrospective analysis of cases of acute flaccid paralysis reported from various districts of Hazara division during the period January 2003 to December 2004. Acute flaccid paralysis was diagnosed clinically through history and clinical examination. The underlying cause of acute flaccid paralysis was investigated by appropriate laboratory tests, such as serum electrolytes, cerebrospinal fluid analysis, electromyogram, nerve conduction study and stool culture for polio virus and other enteroviruses. Diagnosis of Poliomyelitis was confirmed by stool testing for poliovirus. 74 patients presented with AFP during the study period. 36 were male and 38 were female. Guillain Barre syndrome and enteroviral encephalopathy were the two leading causes of acute flaccid paralysis. Majority of the cases were reported from Mansehra district. Children of age groups 12 to 24 months and > 96 months constituted the majority (20% each). Guillian Barre syndrome was the leading cause of acute flaccid paralysis reported from various parts of Hazara division.

Infrastructure Engineering and Deployment Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Infrastructure Engineering and Deployment Division advances transportation innovation by being leaders in infrastructure technology, including vehicles and...

Peptidoglycan architecture can specify division planes in Staphylococcus aureus.

Science.gov (United States)

Turner, Robert D; Ratcliffe, Emma C; Wheeler, Richard; Golestanian, Ramin; Hobbs, Jamie K; Foster, Simon J

2010-06-15

Division in Staphylococci occurs equatorially and on specific sequentially orthogonal planes in three dimensions, resulting, after incomplete cell separation, in the 'bunch of grapes' cluster organization that defines the genus. The shape of Staphylococci is principally maintained by peptidoglycan. In this study, we use Atomic Force Microscopy (AFM) and fluorescence microscopy with vancomycin labelling to examine purified peptidoglycan architecture and its dynamics in Staphylococcus aureus and correlate these with the cell cycle. At the presumptive septum, cells were found to form a large belt of peptidoglycan in the division plane before the centripetal formation of the septal disc; this often had a 'piecrust' texture. After division, the structures remain as orthogonal ribs, encoding the location of past division planes in the cell wall. We propose that this epigenetic information is used to enable S. aureus to divide in sequentially orthogonal planes, explaining how a spherical organism can maintain division plane localization with fidelity over many generations.

Fermilab | Particle Physics Division

Science.gov (United States)

Diversity Education Safety Sustainability and Environment Contact Science Science Particle Physics Neutrinos Scientific Computing Research & Development Key Discoveries Benefits of Particle Physics Particle Superconducting Test Accelerator LHC and Future Accelerators Accelerators for Science and Society Particle Physics

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1980-09-01

Research activities in the Division of Reactor Engineering in fiscal 1979 are described. The work of the Division is closely related to development of multi-purpose Very High Temperature Gas Cooled Reactor and fusion reactor, and development of Liquid Metal Fast Breeder Reactor carried out by Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are achievements in fields such as nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, reactor and nuclear instrumentation, reactor control and diagnosis, and fusion reactor technology, and activities of the Committees on Reactor Physics and on Decomissioning of Nuclear Facilities. (author)

Radiochemistry Division annual progress report : 1991

International Nuclear Information System (INIS)

Natarajan, V.; Godbole, S.V.; Iyer, R.H.

1993-01-01

The research and development activities of the Radiochemistry Division during 1991 are briefly described under the headings: (i) Nuclear chemistry, (ii) Actinide chemistry, and (iii) Spectroscopy. In the field of nuclear chemistry, the main emphasis has been on the studies of fission process induced by reactor neutrons and light and heavy ions on actinides and low Z (Z c superconductors. A list of publications by the scientific staff of the Division is given at the end. (author). 31 figs., 49 tabs

Carlsbad Area Office Waste Isolation Division Transition Plan

International Nuclear Information System (INIS)

1994-01-01

In October 1993, the US Department of Energy (DOE) announced the Revised Test Strategy for the Waste Isolation Pilot Plant (WIPP). The new strategy involves conducting additional radioactive waste tests in laboratories instead of the underground at the WIPP. It will likely result in an acceleration of regulatory compliance activities needed for a disposal decision, which could result in permanent disposal of transuranic waste earlier than the previous test program and regulatory compliance strategy. The Revised Test Strategy changes the near-term program activities for the WIPP site. The revised strategy deletes radioactive waste tests at the WIPP, prior to completing all activities for initiating disposal operations, and consequently the need to maintain readiness to receive waste in the near-term. However, the new strategy enables the DOE to pursue an earlier disposal decision, supported by an accelerated regulatory compliance strategy. With the new strategy, the WIPP must prepare for disposal operations in early 1998. This Westinghouse Waste Isolation Division (WID) Transition Plan addresses the WID programmatic, budgetary, and personnel changes to conform to the Revised Test Strategy, and to support the accelerated compliance strategy and earlier disposal operations at the WIPP

Nuclear Power Division

International Nuclear Information System (INIS)

Anon.

1981-01-01

The 1981-85 research program planned by the Nuclear Power Division of EPRI places major emphasis on the assurance of safety and realiability of light water reactors (LWRs). Of high priority is a better knowledge of LWR-system behavior undeer abnormal conditions and the behavior of structural materials used for pressure vessels, piping, and large nuclear-plant components. Strong emphasis is also placed on achieving the most-effective performance and utilization of nuclear fuels and improving the corrosion resistance of pressurized-water-reactor steam generators. Efforts are underway to reduce radiation exposure and outage duration and to investigate the human factors involved in plant operation and maintenance. Substantial emphasis is placed on short-range goals designed to achieve useful results in the next two to seven years. The Division's mid- and long-range goal is to improve the use of fissionable and fertile materials and aid in the realization of other reactor systems. A series of general goals, categorized into three time frames and planned expenditures shows the trend of work to be undertaken. 53 figures

Contacts in the Office of Pesticide Programs, Registration Division

Science.gov (United States)

The Registration Division (RD) is responsible product registrations, amendments, registrations, tolerances, experimental use permits, and emergency exemptions for conventional chemical pesticides. Find contacts in this division.

Image transmission in multicore-fiber code-division multiple access network

Science.gov (United States)

Yang, Guu-Chang; Kwong, Wing C.

1997-01-01

Recently, two-dimensional (2-D) signature patterns were proposed to encode binary digitized image pixels in optical code-division multiple-access (CDMA) networks with 'multicore' fiber. The new technology enables parallel transmission and simultaneous access of 2-D images in multiple-access environment, where these signature patterns are defined as optical orthogonal signature pattern codes (OOSPCs). However, previous work on OOSPCs assumed that the weight of each signature pattern was the same. In this paper, we construct a new family of OOSPCs with the removal of this assumption. Since varying the weight of a user's signature pattern affects that user's performance, this approach is useful for CDMA optical systems with multiple performance requirements.

Adaptive pole placement: the division by zero problem

NARCIS (Netherlands)

Arent, Krzysztof; Arent, K.; Polderman, Jan W.; Mareels, I.M.Y.; Mareels, Iven

1995-01-01

We re-examine the division by zero problem which occurs in certainty equivalence based indirect adaptive control algorithms applied to linear systems. By exploiting a parametrization for linear systems induced by the continued fraction description of its transfer function, the division by zero

"American Gothic" and the Division of Labor.

Science.gov (United States)

Saunders, Robert J.

1987-01-01

Provides historical review of gender-based division of labor. Argues that gender-based division of labor served a purpose in survival of tribal communities but has lost meaning today and may be a handicap to full use of human talent and ability in the arts. There is nothing in various art forms which make them more appropriate for males or…

Security and Emergency Management Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Security and Emergency Management Division identifies vulnerabilities, risks, and opportunities to improve the security of transportation systems, critical...

QUEST/Ada (query utility environment for software testing of Ada: The development of a program analysis environment for Ada, task 1, phase 3

Science.gov (United States)

Brown, David B.

1991-01-01

The results of research and development efforts of the first six months of Task 1, Phase 3 of the project are presented. The goals of Phase 3 are: (1) to further refine the rule base and complete the comparative rule base evaluation; (2) to implement and evaluate a concurrency testing prototype; (3) to convert the complete (unit-level and concurrency) testing prototype to a workstation environment; and (4) to provide a prototype development document to facilitate the transfer of research technology to a working environment. These goals were partially met and the results are summarized.

Systems Safety and Engineering Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Systems Safety and Engineering Division conducts engineering, research, and analysis to improve transportation safety, capacity, and resiliency. We provide...

Situational Awareness and Logistics Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Situational Awareness and Logistics Division researches, develops, implements, and analyzes advanced systems to protect, enhance, and ensure resilienceof the...

Ecological-economical approach to assessment of environment state at the Semipalatinsk test site

International Nuclear Information System (INIS)

Chugunova, N.S.; Balykbaeva, S.Y.

2002-01-01

The paper presents methods used for ecological-economical assessment of the environment condition at the former Semipalatinsk Test Site. It also presents methodology of calculating ecological and economical parameters for different options. Besides, the paper provides data describing assessment of ecological and economical damage caused by defense establishment activities at the Semipalatinsk Test Site. (author)

Evolutionary dynamics of division of labor games with selfish agents

Science.gov (United States)

Zhang, Jianlei; Li, Qiaoyu; Zhang, Chunyan

2017-11-01

The division of labor is one of the most basic and widely studied aspects of collective behavior in natural systems. Studies of division of labor are concerned with the integration of the individual worker behavior into a colony level task organization and with the question of how the regulation of the division of labor may contribute to the colony efficiency. This paper investigates the evolution of the division of labor with three strategies by employing the evolutionary game theory. Thus, these available strategies are, respectively, strategy A (performing task A), strategy B (performing task B), and strategy D (not performing any task but only free riding others' contributions). And, two typical networks (i.e., BA scale-free network and lattice network) are employed here for describing the interaction structure among agents. The theoretical analysis together with simulation results reveal that the division of labor can evolve and leads to players that differ in their tendency to take on a given task. The conditions under which the division of labor evolves depend on the costs for performing the task, the benefits led by performing the task, and the interaction structures among the players who are involved with division of labor games.

Life Sciences Division annual report, 1988

Energy Technology Data Exchange (ETDEWEB)

Marrone, B.L.; Cram, L.S. (comps.)

1989-04-01

This report summarizes the research and development activities of Los Alamos National Laboratory's Life Sciences Division for the calendar year 1988. Technical reports related to the current status of projects are presented in sufficient detail to permit the informed reader to assess their scope and significance. Summaries useful to the casual reader desiring general information have been prepared by the Group Leaders and appear in each group overview. Investigators on the staff of the Life Sciences Division will be pleased to provide further information.

Nuclear Physics Division: annual report 1991

International Nuclear Information System (INIS)

Betigeri, M.G.

1993-01-01

A brief account of the research and development activities carried out by the Nuclear Physics Division, Bhabha Atomic Research Centre, Bombay during the period January 1991 to December 1991 is presented. These R and D activities are reported under the headings : 1) Accelerator Facilities, 2) Research Activities, and 3) Instrumentation. At the end, a list of publications by the staff scientists of the Division is given. The list includes papers published in journals, papers presented at conferences, symposia etc., and technical reports. (author). figs., tabs

Life Sciences Division annual report, 1988

International Nuclear Information System (INIS)

Marrone, B.L.; Cram, L.S.

1989-04-01

This report summarizes the research and development activities of Los Alamos National Laboratory's Life Sciences Division for the calendar year 1988. Technical reports related to the current status of projects are presented in sufficient detail to permit the informed reader to assess their scope and significance. Summaries useful to the casual reader desiring general information have been prepared by the Group Leaders and appear in each group overview. Investigators on the staff of the Life Sciences Division will be pleased to provide further information

Relationship between Physiological Off-Ice Testing, On-Ice Skating, and Game Performance in Division I Women's Ice Hockey Players.

Science.gov (United States)

Boland, Michelle; Miele, Emily M; Delude, Katie

2017-10-07

The purpose was to identify off-ice testing variables that correlate to skating and game performance in Division I collegiate women ice hockey players. Twenty female, forward and defensive players (19.95 ± 1.35 yr) were assessed for weight, height, percent fat mass (%FAT), bone mineral density, predicted one repetition maximum (RM) absolute and relative (REL%) bench press (BP) and hex bar deadlift (HDL), lower body explosive power, anaerobic power, countermovement vertical jump (CMJ), maximum inspiratory pressure (MIP), and on-ice repeated skate sprint (RSS) performance. The on-ice RSS test included 6 timed 85.6 m sprints with participants wearing full hockey equipment; fastest time (FT), average time (AT) and fatigue index (FI) for the first length skate (FLS; 10 m) and total length skate (TLS; 85.6 m) were used for analysis. Game performance was evaluated with game statistics: goals, assists, points, plus-minus, and shots on goal (SOG). Correlation coefficients were used to determine relationships. Percent fat mass was positively correlated (p Game performance in women ice hockey players may be enhanced by greater MIP, repeat acceleration ability, and mode-specific training. Faster skating times were associated with lower %FAT. Skating performance in women ice hockey players may be enhanced by improving body composition, anaerobic power, and both lower and upper body strength in off-ice training.

Laser and Plasma Technology Division, Annual Reports 1996 and 1997

International Nuclear Information System (INIS)

Venkatramani, N.

1999-04-01

This report describes the activity of the Laser and Plasma Technology Division of Bhabha Atomic Research Centre during the two year period 1996- 1997. This division is engaged in the research and development of high power beams mainly laser, plasma and electron beams. Laser and Plasma Technology Division has strived to establish indigenous capability to cater to the requirements of Department of Atomic Energy. This involves development and technology readiness study of laser, plasma and electron beam devices. In addition, studies are also carried out on related physical phenomenon with a view to gain better understanding of the devices. This report has been compiled from individual reports of various groups/sections working in the division. A list of publications by the several members of the division is also included. (author)

HISTORY OF THE ENGINEERING PHYSICS AND MATHEMATICS DIVISION 1955-1993

Energy Technology Data Exchange (ETDEWEB)

Maskewitz, B.F.

2001-09-14

A review of division progress reports noting significant events and findings of the Applied Nuclear Physics, Neutron Physics, Engineering Physics, and then Engineering Physics and Mathematics divisions from 1955 to 1993 was prepared for use in developing a history of the Oak Ridge National Laboratory in celebration of its 50th year. The research resulted in an accumulation of historic material and photographs covering 38 years of effort, and the decision was made to publish a brief history of the division. The history begins with a detailed account of the founding of the Applied Nuclear Physics Division in 1955 and continues through the name change to the Neutron Physics Division in the late 1950s. The material thereafter is presented in decades--the sixties, seventies, and eighties--and ends as we enter the nineties.

A division algebra classification of generalized supersymmetries

International Nuclear Information System (INIS)

Toppan, Francesco

2004-10-01

Generalized supersymmetries admitting bosonic tensor central charges are classified in accordance with their division algebra properties. Division algebra consistent constraints lead (in the complex and quaternionic cases) to the classes of hermitian and holomorphic generalized supersymmetries. Applications to the analytic continuation of the M-algebra to the Euclidean and the systematic investigation of certain classes of models in generic space-times are briefly mentioned. (author)

78 FR 49111 - Airworthiness Directives; Pratt & Whitney Division Turbofan Engines

Science.gov (United States)

2013-08-13

... Airworthiness Directives; Pratt & Whitney Division Turbofan Engines AGENCY: Federal Aviation Administration (FAA... & Whitney Division (PW) turbofan engine model PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090...) Applicability This AD applies to all Pratt & Whitney Division (PW) turbofan engine models PW4074, PW4074D...

Laser and Plasma Technology Division annual report 1995

International Nuclear Information System (INIS)

Venkatramani, N.

1996-01-01

This report describes the activity of the Laser and Plasma Technology Division of Bhabha Atomic Research Centre, Mumbai during the period 1995. This division is engaged in the research and development of high power beams namely lasers, plasma and electron beams which are characterized by high power density. This division has strived to establish indigenous capability to cater to the requirements of the Department of Atomic Energy. The broad program objectives of the division are (1) development and technology readiness studies of laser, plasma and electron beam devices; (2) studies on related physical phenomena with a view to gain better understanding of the devices and (3) improvements in technology and exploration of new areas. This report has been compiled from individual reports of various groups/sections with marginal editing. At the end of each section; a list of publications by the staff members in the field indicated by the title of the section is given. refs., figs., tabs

Phenotypic Tests for the Detection of β-Lactamase-Producing Enterobacteriaceae Isolated from Different Environments.

Science.gov (United States)

de Oliveira, Daniele V; Van Der Sand, Sueli T

2016-07-01

Some bacteria from the Enterobacteriaceae family are showing a significant capability to disseminate β-lactams resistance mechanisms among them, and these same mechanisms can be carried out from the hospital environment to superficial water. The aim of this study was to evaluate different phenotypic methods for the detection β-lactamases production by enterobacteria isolated from the anthropogenic environment: hospital wastewater and from a stream that cross the city of Porto Alegre. The applied tests were the modified Hodge test (MHT) and phenotypic tests with the following inhibitors: carbapenemase-phenylboronic acid (APB), metallo-β-lactamase-EDTA, AmpC β-lactamase-cloxacillin, and the confirmatory test for extended-spectrum β-lactamase (ESBL)-clavulanic acid. For this evaluation, 131 isolates were initially subjected to antibiogram using the following antimicrobials: cefotaxime (30 µg), cefpodoxime (10 μg), ceftazidime (30 µg), ertapenem (10 μg), meropenem (10 μg), and aztreonam (30 μg). After this first screening, 62 isolates showed a profile resistance for at least one antimicrobial. These isolates were subjected to all phenotypic tests. Of those, 40 isolates were positive for at least one phenotypic test. In MHT test, one isolate was positive and five were with inconclusive results. The results achieved with the inhibitors are as follows: APB 25/40 positive strains; EDTA 8/40 positive strains; and with CLOXA 2/40 positive strains. ESBL production was observed for 34/40 strains. This assessment shows a high level of bacteria which can produce enzymes that inactivate β-lactams present in the different environment like the stream waters and from the hospital settings.

Engineering Physics and Mathematics Division progress report for period ending December 31, 1994

International Nuclear Information System (INIS)

Sincovec, R.F.

1995-07-01

This report provides a record of the research activities of the Engineering Physics and Mathematics Division for the period January 1, 1993, through December 31, 1994. This report is the final archival record of the EPM Division. On October 1, 1994, ORELA was transferred to Physics Division and on January 1, 1995, the Engineering Physics and Mathematics Division and the Computer Applications Division reorganized to form the Computer Science and Mathematics Division and the Computational Physics and Engineering Division. Earlier reports in this series are identified on the previous pages, along with the progress reports describing ORNL's research in the mathematical sciences prior to 1984 when those activities moved into the Engineering Physics and Mathematics Division

Engineering Physics and Mathematics Division progress report for period ending December 31, 1994

Energy Technology Data Exchange (ETDEWEB)

Sincovec, R.F.

1995-07-01

This report provides a record of the research activities of the Engineering Physics and Mathematics Division for the period January 1, 1993, through December 31, 1994. This report is the final archival record of the EPM Division. On October 1, 1994, ORELA was transferred to Physics Division and on January 1, 1995, the Engineering Physics and Mathematics Division and the Computer Applications Division reorganized to form the Computer Science and Mathematics Division and the Computational Physics and Engineering Division. Earlier reports in this series are identified on the previous pages, along with the progress reports describing ORNL`s research in the mathematical sciences prior to 1984 when those activities moved into the Engineering Physics and Mathematics Division.

Multi-modal virtual environment research at Armstrong Laboratory

Science.gov (United States)

Eggleston, Robert G.

1995-01-01

One mission of the Paul M. Fitts Human Engineering Division of Armstrong Laboratory is to improve the user interface for complex systems through user-centered exploratory development and research activities. In support of this goal, many current projects attempt to advance and exploit user-interface concepts made possible by virtual reality (VR) technologies. Virtual environments may be used as a general purpose interface medium, an alternative display/control method, a data visualization and analysis tool, or a graphically based performance assessment tool. An overview is given of research projects within the division on prototype interface hardware/software development, integrated interface concept development, interface design and evaluation tool development, and user and mission performance evaluation tool development.

New Compensation Technique for Fiber Impairments in Ultra High Capacity Super channel Based on (QDPASK Dense wavelength division multiplex (DWDM systems

Directory of Open Access Journals (Sweden)

Ibrahim A.Murdas

2017-07-01

Full Text Available In this paper we want to increase the data rate and to get larger transmission distance, therefore we use the Advanced modulation technique QDPASK in DWDM system with low channels space. In case of long transmission distance and multi channels system both giving rise to inter channel crosstalk induced by fiber nonlinearities as a result the use of advanced modulation technique becomes difficult. In this paper Quaternary differential phase amplitude shift keying (QDPASK is designed for 32 dense wavelength division multiplexing (DWDM channels, therefore we proposed a new cascade compensation system consist of optical and digital back propagation techniques (ODBP for compensate the linear and nonlinear effects . A performance of the system was reported using QDPASK DWDM fiber-optic system for various system parameters. The research is tested in VPI maker environment.

AC/ARNG Integrated Division Concept Study, Appendices, Volume 3

National Research Council Canada - National Science Library

Twohig, John

1997-01-01

...) division headquarters. The US Army Training and Doctrine Command (TRADOC) was tasked to conduct a viability assessment of the AC/ARNG Integrated Division concept and focus on merits and implementation issues...

Isotope and Nuclear Chemistry Division annual report, FY 1983

International Nuclear Information System (INIS)

Heiken, J.H.; Lindberg, H.A.

1984-05-01

This report describes progress in the major research and development programs carried out in FY 1983 by the Isotope and Nuclear Chemistry Division. It covers radiochemical diagnostics of weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production, separation, and applications (including biomedical applications); element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced analytical techniques; development and applications; atmospheric chemistry and transport; and earth and planetary processes

Isotope and Nuclear Chemistry Division annual report, FY 1983

Energy Technology Data Exchange (ETDEWEB)

Heiken, J.H.; Lindberg, H.A. (eds.)

1984-05-01

This report describes progress in the major research and development programs carried out in FY 1983 by the Isotope and Nuclear Chemistry Division. It covers radiochemical diagnostics of weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production, separation, and applications (including biomedical applications); element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced analytical techniques; development and applications; atmospheric chemistry and transport; and earth and planetary processes.

Isotope and Nuclear Chemistry Division annual report, FY 1984

International Nuclear Information System (INIS)

Heiken, J.H.

1985-04-01

This report describes progress in the major research and development programs carried out in FY 1984 by the Isotope and Nuclear Chemistry Division. It covers radiochemical diagnostics of weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production, separation, and applications (including biomedical applications); element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced analytical techniques: development and applications; atmospheric chemistry and transport; and earth and planetary processes. 287 refs

Cell Division and Evolution of Biological Tissues

Science.gov (United States)

Rivier, Nicolas; Arcenegui-Siemens, Xavier; Schliecker, Gudrun

A tissue is a geometrical, space-filling, random cellular network; it remains in this steady state while individual cells divide. Cell division (fragmentation) is a local, elementary topological transformation which establishes statistical equilibrium of the structure. Statistical equilibrium is characterized by observable relations (Lewis, Aboav) between cell shapes, sizes and those of their neighbours, obtained through maximum entropy and topological correlation extending to nearest neighbours only, i.e. maximal randomness. For a two-dimensional tissue (epithelium), the distribution of cell shapes and that of mother and daughter cells can be obtained from elementary geometrical and physical arguments, except for an exponential factor favouring division of larger cells, and exponential and combinatorial factors encouraging a most symmetric division. The resulting distributions are very narrow, and stationarity severely restricts the range of an adjustable structural parameter

Chemical Technology Division annual technical report, 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

CMT is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. It conducts R&D in 3 general areas: development of advanced power sources for stationary and transportation applications and for consumer electronics, management of high-level and low-level nuclear wastes and hazardous wastes, and electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, materials chemistry of electrified interfaces and molecular sieves, and the theory of materials properties. It also operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at ANL and other organizations. Technical highlights of the Division`s activities during 1996 are presented.

Division of labour and the evolution of extreme specialization.

Science.gov (United States)

Cooper, Guy A; West, Stuart A

2018-05-28

Division of labour is a common feature of social groups, from biofilms to complex animal societies. However, we lack a theoretical framework that can explain why division of labour has evolved on certain branches of the tree of life but not others. Here, we model the division of labour over a cooperative behaviour, considering both when it should evolve and the extent to which the different types should become specialized. We found that: (1) division of labour is usually-but not always-favoured by high efficiency benefits to specialization and low within-group conflict; and (2) natural selection favours extreme specialization, where some individuals are completely dependent on the helping behaviour of others. We make a number of predictions, several of which are supported by the existing empirical data, from microbes and animals, while others suggest novel directions for empirical work. More generally, we show how division of labour can lead to mutual dependence between different individuals and hence drive major evolutionary transitions, such as those to multicellularity and eusociality.

Bulletin of the Division of Electrical Engineering, 1987-1988, volume 3, number 2

Science.gov (United States)

1988-05-01

A report is provided on the activities of the Division of Electrical Engineering of the National Research Council of Canada. The Division engages in the development of standards and test procedures, and undertakes applied research in support of Canadian industry, government departments, and universities. Technology transfer and collaborative research continue to grow in importance as focuses of Division activities. The Division is comprised of three sections: the Laboratory for Biomedical Engineering, the Laboratory for Electromagnetic and Power Engineering, and the Laboratory for Intelligent Systems. An agreement has been reached to commercially exploit the realtime multiprocessor operating system Harmony. The dielectrics group has made contract research agreements with industry from both Canada and the United States. The possibility of employing a new advanced laser vision camera, which can be mounted on a robot arm in a variety of industrial applications is being explored. Potential short-term spinoffs related to intelligent wheelchairs are being sought as part of the new interlaboratory program which has as its long-term objective the development of a mobile robot for health care applications. A program in applied artificial intelligence has been established. Initiatives in collaboration with outside groups include proposals for major institutes in areas ranging from police and security research to rehabilitation research, programs to enhance Canadian industrial competence working with the Canadian Manufacturers' Association and other government departments, and approaches to the utilization of existing facilities which will make them more valuable without significant financial expenditures.

A novel cell division factor from tobacco 2B-13 cells that induced cell division in auxin-starved tobacco BY-2 cells

Science.gov (United States)

Shimizu, Takashi; Eguchi, Kentaro; Nishida, Ikuo; Laukens, Kris; Witters, Erwin; van Onckelen, Harry; Nagata, Toshiyuki

2006-06-01

Effects of auxin as plant hormones are widespread; in fact in almost all aspects of plant growth and development auxin plays a pivotal role. Although auxin is required for propagating cell division in plant cells, its effect upon cell division is least understood. If auxin is depleted from the culture medium, cultured cells cease to divide. It has been demonstrated in this context that the addition of auxin to auxin-starved nondividing tobacco BY-2 cells induced semisynchronous cell division. On the other hand, there are some cell lines, named habituated cells, that can grow without auxin. The cause and reason for the habituated cells have not been clarified. A habituated cell line named 2B-13 is derived from the tobacco BY-2 cell line, which has been most intensively studied among plant cell lines. When we tried to find the difference between two cell lines of BY-2 and 2B-13 cells, we found that the addition of culture filtrated from the auxin-habituated 2B-13 cells induced semisynchronous cell division in auxin-starved BY-2 cells. The cell division factor (CDF) that is responsible for inducing cell division in auxin-starved BY-2 cells was purified to near-homogeneity by sequential passage through a hydroxyapatite column, a ConA Sepharose column and a Sephadex gel filtration column. The resulting purified fraction appeared as a single band of high molecular weight on sodium dodecyl sulfate-polyacrylamide gel electrophoresis gels by silver staining and was able to induce cell division in auxin-starved BY-2 cells. Identification of the protein by MALD-TOF-MS/MS revealed that it is structurally related to P-glycoprotein from Gossypioides kirkii, which belongs to ATP-binding cassette (ABC)-transporters. The significance of CDF as a possible ABC-transporter is discussed in relationship to auxin-autotrophic growth and auxin-signaling pathway.

Fraction Multiplication and Division Word Problems Posed by Different Years of Pre-Service Elementary Mathematics Teachers

Directory of Open Access Journals (Sweden)

Tuba Aydogdu Iskenderoglu

2018-04-01

Full Text Available It is important for pre-service teachers to know the conceptual difficulties they have experienced regarding the concepts of multiplication and division in fractions and problem posing is a way to learn these conceptual difficulties. Problem posing is a synthetic activity that fundamentally has multiple answers. The purpose of this study is to analyze the multiplication and division of fractions problems posed by pre-service elementary mathematics teachers and to investigate how the problems posed change according to the year of study the pre-service teachers are in. The study employed developmental research methods. A total of 213 pre-service teachers enrolled in different years of the Elementary Mathematics Teaching program at a state university in Turkey took part in the study. The “Problem Posing Test” was used as the data collecting tool. In this test, there are 3 multiplication and 3 division operations. The data were analyzed using qualitative descriptive analysis. The findings suggest that, regardless of the year, pre-service teachers had more conceptual difficulties in problem posing about the division of fractions than in problem posing about the multiplication of fractions.

Theoretical Division progress report. [October 1976-January 1979

Energy Technology Data Exchange (ETDEWEB)

Cooper, N.G. (comp.)

1979-04-01

This report presents highlights of activities in the Theoretical (T) Division from October 1976-January 1979. The report is divided into three parts. Part I presents an overview of the Division: its unique function at the Los Alamos Scientific Laboratory (LASL) and within the scientific community as a whole; the organization of personnel; the main areas of research; and a survey of recent T-Division initiatives. This overview is followed by a survey of the 13 groups within the Division, their main responsibilities, interests, and expertise, consulting activities, and recent scientific accomplisments. The remainder of the report, Parts II and III, is devoted to articles on selected research activities. Recent efforts on topics of immediate interest to energy and weapons programs at LASL and elsewhere are described in Part II, Major National Programs. Separate articles present T-Divison contributions to weapons research, reactor safety and reactor physics research, fusion research, laser isotope separation, and other energy research. Each article is a compilation of independent projects within T Division, all related to but addressing different aspects of the major program. Part III is organized by subject discipline, and describes recent scientific advances of fundamental interest. An introduction, defining the scope and general nature of T-Division efforts within a given discipline, is followed by articles on the research topics selected. The reporting is done by the scientists involved in the research, and an attempt is made to communicate to a general audience. Some data are given incidentally; more technical presentations of the research accomplished may be found among the 47 pages of references. 110 figures, 5 tables.

Theoretical Physics Division

International Nuclear Information System (INIS)

This report is a survey of the studies done in the Theoretical Physics Division of the Nuclear Physics Institute; the subjects studied in theoretical nuclear physics were the few-nucleon problem, nuclear structure, nuclear reactions, weak interactions, intermediate energy and high energy physics. In this last field, the subjects studied were field theory, group theory, symmetry and strong interactions [fr

Presence in a Three-Dimensional Test Environment: Benefit or Threat to Market Research?

OpenAIRE

Alma Berneburg

2008-01-01

In market research, the adoption of interactive virtual reality-techniques could be expected to contain many advantages: artificial lab environments could be designed in a more realistic manner and the consideration of “time to the market”-factors could be improved. On the other hand, with an increasing degree of presence and the notional attendance in a simulated test environment, the market research task could fall prey to the tensing virtual reality adventure. In...

Formation of a cylindrical bridge in cell division

Science.gov (United States)

Citron, Daniel; Schmidt, Laura E.; Reichl, Elizabeth; Ren, Yixin; Robinson, Douglas; Zhang, Wendy W.

2007-11-01

In nature, the shape transition associated with the division of a mother cell into two daughter cells proceeds via a variety of routes. In the cylinder-thinning route, which has been observed in Dictyostelium and most animal cells, the mother cell first forms a broad bridge-like region, also known as a furrow, between two daughter cells. The furrow then rapidly evolves into a cylindrical bridge, which thins and eventually severs the mother cell into two. The fundamental mechanism underlying this division route is not understood. Recent experiments on Dictyostelium found that, while the cylinder-thinning route persists even when key actin cross-linking proteins are missing, it is disrupted by the removal of force-generating myosin-II proteins. Other measurements revealed that mutant cells lacking myosin-II have a much more uniform tension over the cell surface than wild-type cells. This suggests that tension variation may be important. Here we use a fluid model, previously shown to reproduce the thinning dynamics [Zhang & Robinson, PNAS 102, 7186 (2005)], to test this idea. Consistent with the experiments, the model shows that the cylinder formation process occurs regardless of the exact viscoelastic properties of the cell. In contrast to the experiments, a tension variation in the model hinders, rather then expedites, the cylinder formation.

Tests on standard concrete samples

CERN Multimedia

CERN PhotoLab

1973-01-01

Compression and tensile tests on standard concrete samples. The use of centrifugal force in tensile testing has been developed by the SB Division and the instruments were built in the Central workshops.

Activity Report of Reactor Physics Division - 1997

International Nuclear Information System (INIS)

Singh, Om Pal

1998-01-01

The research and development activities of the Reactor Physics Division of the Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam during 1997 are reported. The activities are arranged under the headings: nuclear data processing and validation, PFBR and KAMINI core physics, FBTR core physics, radioactivity and shielding and safety analysis. A list of publications of the Division and seminars delivered are included at the end of the report

Power Efficient Division and Square Root Unit

DEFF Research Database (Denmark)

Liu, Wei; Nannarelli, Alberto

2012-01-01

Although division and square root are not frequent operations, most processors implement them in hardware to not compromise the overall performance. Two classes of algorithms implement division or square root: digit-recurrence and multiplicative (e.g., Newton-Raphson) algorithms. Previous work....... The proposed unit is compared to similar solutions based on the digit-recurrence algorithm and it is compared to a unit based on the multiplicative Newton-Raphson algorithm....

Standard Test Methods for Photovoltaic Modules in Cyclic Temperature and Humidity Environments

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 These test methods provide procedures for stressing photovoltaic modules in simulated temperature and humidity environments. Environmental testing is used to simulate aging of module materials on an accelerated basis. 1.2 Three individual environmental test procedures are defined by these test methods: a thermal cycling procedure, a humidity-freeze cycling procedure, and an extended duration damp heat procedure. Electrical biasing is utilized during the thermal cycling procedure to simulate stresses that are known to occur in field-deployed modules. 1.3 These test methods define mounting methods for modules undergoing environmental testing, and specify parameters that must be recorded and reported. 1.4 These test methods do not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of these test methods. 1.5 Any of the individual environmental tests may be performed singly, or may be combined into a test sequence with other environmental or non-envir...

SERVICE HANDBOOK FOR THE DESKTOP SUPPORT CONTRACT WIH IT DIVISION

CERN Multimedia

2000-01-01

A Desktop Support Contract has been running since January 1999 to offer help to all users at CERN with problems that occur with their desktop computers. The contract is run conjointly by the Swedish Company WM-data and the Swiss company DCS.The contract is comprised of the Computing Helpdesk, a General Service for all parts of CERN and also Local Service for those divisions and groups that want faster response times and additional help with their specific computer environment.In order to describe what services are being offered, and also to give a better understanding of the structure of the contract, a Service Handbook has been created. The intended audience for the Service Handbook is everyone that is using the contract, i.e. users, managers and also the service staff inside the contract. In the handbook you will find what help you can get from the contract, how to get in touch with the contract, and also what response times you can expect. Since the computer environment at CERN is a never-changing entity, ...

76 FR 34246 - Automated Commercial Environment (ACE); Announcement of National Customs Automation Program Test...

Science.gov (United States)

2011-06-13

... Environment (ACE); Announcement of National Customs Automation Program Test of Automated Procedures for In... Customs Automation Program (NCAP) test relating to highway movements of commercial goods that are transported in-bond through the United States from one point in Canada to another point in Canada. The NCAP...

Predictive testing of performance of metals in HTR service environments

International Nuclear Information System (INIS)

Kondo, T.; Shindo, M.; Tamura, M.; Tsuji, H.; Kurata, Y.; Tsukada, T.

1982-01-01

Status of the material testing in simulated HTGR environment is reviewed with special attention focused on the methodology of the prediction of performance in long time. Importance of controlling effective chemical potentials relations in the material-environmental interface is stressed in regard of the complex inter-dependent kinetic relation between oxidation and carbon transport. Based on the recent experimental observations, proposals are made to establish some procedures for conservative prediction of the metal performance

Accident response -- X-ray to virtual environment

International Nuclear Information System (INIS)

Hefele, J.; Stupin, D.; Kelley, T.; Sheats, M.; Tsai, C.

1999-01-01

The Engineering Sciences and Applications (ESA) Division of Los Alamos National Laboratory (LANL) has been working to develop a process to extract topographical information from digital x-ray data for modeling in a Computer Aided Design (CAD) environment and translation into a virtual environment. The application for this process is the evolution of a field deployable tool for use by the Accident Response Group (ARG) at the Laboratory. The authors have used both CT Scan and radiography data in their process development. The data is translated into a format recognizable by Pro/ENGINEER trademark and then into a virtual environment that can be operated on by dVISE trademark. They have successfully taken both CT Scan and radiograph data of single components and created solid and virtual environment models for interrogation

Preseason physiological profile of soccer and basketball players in different divisions.

Science.gov (United States)

Metaxas, Thomas I; Koutlianos, Nikos; Sendelides, Thomas; Mandroukas, Athanasios

2009-09-01

The purpose of this study was to examine and compare the cardiorespiratory performance and isokinetic muscle strength between Greek soccer and basketball players of different divisions before starting the training season. Study participants included 100 soccer players and 61 basketball players, who were assigned according to the kind of sport and division. All participants underwent anthropometric measurements and performed an exercise test on a treadmill to determine maximal oxygen uptake (VO2max). Peak torque for quadriceps and hamstring muscles was measured on isokinetic dynamometer at angular velocity of 60 degrees/s(-1), 180 degrees/s(-1), and 300 degrees/s(-1). The statistical p value was set at p duration of the maintenance period and to the effect of the training session on each sport, respectively. Finally, a higher level of muscle strength would be preferable in soccer and basketball and would reduce the risk for injuries in the maintenance and rebuilding training periods.

The Battle River Project: school division implementation of the health-promoting schools approach: assessment for learning: using student health and school capacity measures to inform action and direct policy in a local school district.

Science.gov (United States)

Gleddie, Douglas L; Hobin, Erin P

2011-03-01

The Battle River Project (BRP) is a school division-level intervention in rural Alberta, Canada, built upon the health-promoting schools approach to health promotion. Using self-reported school and student-level data from administrators and students, the central aim of the BRP is to examine: 'How can the school environment and health behaviours (healthy eating, physical activity and mental wellness) of children and youth be improved when a health-promoting schools model, the Ever Active Schools program, is implemented with school division support?' Evidence used to inform school level changes included students' demographic, behavioral, and psychosocial variables linked to school environment data, comprised of school demographics and administrator-assessed quality of policies, facilities, and programs related to physical activity. Each participating school and the division were provided with a tailored report of their schools' results to reflect, plan and implement for positive health behavior change. The main lesson learned was that sharing school-specific evidence can operate as a catalyst for embedding health promoting policy and practices within the school and division culture.

The EGU Seismology Division Early Career Scientist Representative team and its initiatives

Science.gov (United States)

Parisi, Laura; Ermert, Laura; Gualtieri, Lucia; Spieker, Kathrin; Van Noten, Koen; Agius, Matthew R.; Mai, P. Martin

2017-04-01

Since 2014, the Seismology Division (SM) of the European Geosciences Union (EGU) has its Early Career Scientist (ECS) representative to reach out to its numerous 'younger' members. In April 2016, a new team of representatives joined the Division. We are a vivid team of early career scientists, representing both (either) PhD students and post-doctoral researchers working in different seismological disciplines and different countries. The initiatives of the SM ECS-rep team have various aims: (1) to motivate the ECSs to get involved in activities and initiatives of the EGU and the Seismology Division, (2) to promote the research of ECSs, (3) to discuss issues concerning seismologists during this particular stage of their career, (4) to share ideas on how to promote equality between scientists and (5) to improve on the public dissemination of scientific knowledge. In an effort to reach out to experienced and ECS seismologists more effectively and to continuously encourage to voice their ideas by contributing and following our initiatives, a blog and social media pages dedicated to seismology and earthquake trivia are run by the team. Weekly posts are published on the blog and shared on the social media regarding scientific and social aspects of seismology. One of the major contributions recently introduced to the blog is the "Paper of the Month" series where experienced seismologists write about recent or classical - must read - seismology articles. We also aim to organise and promote social and scientific events. During the EGU General Assembly 2016 a social event was held in Vienna allowing ECS to network with peers in an informal environment. Given the success of this event, a similar event will be organized during the General Assembly 2017. Also, similar to previous years, a short course on basic seismology for non seismologists will be requested and offered to all ECSs attending the General Assembly. Finally, a workshop dedicated entirely to ECSs seismologists

Genes involved in cell division in mycoplasmas

Directory of Open Access Journals (Sweden)

Frank Alarcón

2007-01-01

Full Text Available Bacterial cell division has been studied mainly in model systems such as Escherichia coli and Bacillus subtilis, where it is described as a complex process with the participation of a group of proteins which assemble into a multiprotein complex called the septal ring. Mycoplasmas are cell wall-less bacteria presenting a reduced genome. Thus, it was important to compare their genomes to analyze putative genes involved in cell division processes. The division and cell wall (dcw cluster, which in E. coli and B. subtilis is composed of 16 and 17 genes, respectively, is represented by only three to four genes in mycoplasmas. Even the most conserved protein, FtsZ, is not present in all mycoplasma genomes analyzed so far. A model for the FtsZ protein from Mycoplasma hyopneumoniae and Mycoplasma synoviae has been constructed. The conserved residues, essential for GTP/GDP binding, are present in FtsZ from both species. A strong conservation of hydrophobic amino acid patterns is observed, and is probably necessary for the structural stability of the protein when active. M. synoviae FtsZ presents an extended amino acid sequence at the C-terminal portion of the protein, which may participate in interactions with other still unknown proteins crucial for the cell division process.

Progress report [of] Technical Physics Division

International Nuclear Information System (INIS)

Vijendran, P.; Deshpande, R.Y.

1975-01-01

Activities of the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, over the last few years are reported. This division is engaged in developing various technologies supporting the development of nuclear technology. The various fields in which development is actively being carried out are : (i) vacuum technology, (ii) mass spectrometry, (iii) crystal technology, (iv) cryogenics, and (v) magnet technology. For surface studies, the field emission microscope and the Auger electron spectrometer and other types of spectrometers have been devised and perfected. Electromagnets of requisite strength to be used in MHD programme and NMR instruments are being fabricated. Various crystals such as NaI(Tl), Ge, Fluorides, etc. required as windows and prisms in X and gamma-ray spectroscopy, have been grown. In the cryogenics field, expansion engines required for air liquefaction plants, vacuum insulated dewars, helium gas thermometers etc. have been constructed. In addition to the above, the Division provides consultancy and training to personnel from various institutions and laboratories. Equipment and systems perfected are transferred to commercial organizations for regular production. (A.K.)

The Astrophysics Science Division Annual Report 2008

Science.gov (United States)

Oegerle, William; Reddy, Francis; Tyler, Pat

2009-01-01

The Astrophysics Science Division (ASD) at Goddard Space Flight Center (GSFC) is one of the largest and most diverse astrophysical organizations in the world, with activities spanning a broad range of topics in theory, observation, and mission and technology development. Scientific research is carried out over the entire electromagnetic spectrum from gamma rays to radio wavelengths as well as particle physics and gravitational radiation. Members of ASD also provide the scientific operations for three orbiting astrophysics missions WMAP, RXTE, and Swift, as well as the Science Support Center for the Fermi Gamma-ray Space Telescope. A number of key technologies for future missions are also under development in the Division, including X-ray mirrors, and new detectors operating at gamma-ray, X-ray, ultraviolet, infrared, and radio wavelengths. This report includes the Division's activities during 2008.

The effects of test environment and cyclic stretching on the failure properties of human patellar tendons

International Nuclear Information System (INIS)

Haut, R.C.; Powlison, A.C.

1990-01-01

There is a need to document the mechanical properties of patellar tendon allografts used for reconstructive surgery of the damaged anterior cruciate ligament, especially the effects of irradiation sterilization. The purpose of this study was to investigate the influences of in vitro test environment and low-level cyclic stretching prior to failure tests on nonirradiated and irradiated human graft tissues. Bilateral patellar tendons were split and each half processed accordingly. Some graft tissues were stretched cyclically at 2.5 mm deformation before failure. Experiments were performed in a 37 degrees C saline bath or with tissues moistened with a drip of the same. The irradiated grafts relaxed less and generated less slack length in the drip environment than the nonirradiated controls. Cyclic stretching did not alter failure characteristics of either graft tissue. While no significant differences in the tensile responses or failure characteristics were noted for irradiated and nonirradiated grafts in the drip, in the bath environment the nonirradiated tissues had greater strength and modulus. This resulted in there being a significant difference between irradiated and nonirradiated tissue responses in a heated saline bath environment. These experimental results exemplify the need to control in vitro test environments in the evaluation of various sterilization and preservation protocols for soft tissue allografts

Mechanical properties test program on structural materials in a sodium environment

International Nuclear Information System (INIS)

Natesan, K.; Chopra, O.K.; Kassner, T.F.

1979-10-01

This document describes in detail the ongoing and planned US Test program on the mechanical properties of sodium-exposed Type 316 austenitic stainless and Fe-2 1/4 Cr-1 Mo ferritic steels. The test program is based on the Development Requirement Specifications (DRS) established by the DOE/Clinch River Breeder Reactor Project (CRBRP) Program Office, the general need for the development of LMFBR structural-design criteria established by the Nuclear Systems Materials Handbook, and the need for a fundamental understanding of materials behavior in a sodium environment, which is generic to LMFBR systems. The planned test program is an extension of work based on current knowledge of sodium chemistry and the influence of sodium purity on the mechanical properties of structural materials

Reactor Engineering Division annual report

International Nuclear Information System (INIS)

1975-02-01

This report summarizes main research achievements in the 48th fiscal year which were made by Reactor Engineering Division consisted of eight laboratories and Computing Center. The major research and development projects, with which the research programmes in the Division are associated, are development of High Temperature Gas Cooled Reactor for multi-purpose use, development of Liquid Metal Fast Breeder Reactor conducted by Power Reactor and Nuclear Fuel Development Corporation, and Engineering Research Programme for Thermonuclear Fusion Reactor. Many achievements are reported in various research items such as nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, heat transfer and fluid dynamics, reactor and nuclear instrumentation, dynamics analysis and control method development, fusion reactor technology and activities of Computing Center. (auth.)

Earth Sciences Division, collected abstracts-1977. [Research programs

Energy Technology Data Exchange (ETDEWEB)

Quitiquit, W.A.; Ledbetter, G.P.; Henry, A.L.

1978-05-24

This report is a compilation of abstracts of papers, internal reports, and talks presented during 1977 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore Laboratory. It is arranged alphabetically by author and includes a cross-reference by subject indicating the areas of research interest of the Earth Sciences Division.

Motivation Cards to Support Students’ Understanding on Fraction Division

Directory of Open Access Journals (Sweden)

Kamirsyah Wahyu

2017-02-01

Full Text Available This design research aims to develop a learning activity which supports the fifth-grade students to understand measurement fraction division problems (A whole number divided by a fraction that result in a whole number answer conceptually. Furthermore, how students solve the fraction division problem using models is also analyzed.  Data for the retrospective analysis is collected through two teaching experiments in the form of students’ work, field notes, and some part of classroom discussions. The important findings in this research are: 1 the developed learning activity namely Motivation Cards support students understand that  3 divided by one-half means how many one-half are in 3 through models. However, when the divisor is not a unit fraction they could not directly relate the unshaded part in area model for example. 2 area model is proper model to be firstly introduced when the students work on fraction division. 3 understanding this kind of fraction division help students understand other measurement fraction division where both divisor and dividend are fractions. 4 the learning activity supports the development of character values for students.    

Hardware-in-the-loop environment for the design and test of regulators in the refrigeration technology; Hardware-in-the-Loop Umgebung fuer den Entwurf und Test von kaeltetechnischen Reglern

Energy Technology Data Exchange (ETDEWEB)

Koeberle, Thomas; Becker, Martin [Hochschule Biberach (Germany). Inst. fuer Gebaeude- und Energiesysteme

2012-07-01

In its Directive on energy efficiency, The European Commission has specified a target value for saving primary energy by 20 % up the year 2020. According to current projections, the target will be failed by half. This is why significantly more efforts are needed. The energy consumption of the technical supply of coldness amounts nearly 14 % of the total consumption of electrical power in Germany. The Research Council Coldness specifies that the potential for energy conservation in the refrigeration engineering amounts up to 40 %. Thus, more effort must be made in the refrigeration engineering in order to reach the energy saving targets of the European Commission. Thereby, the major portion of the potential of energy saving consists of the establishment of the requirements in regard to system concepts and components as well as the control. The control of refrigeration systems provides a simple possibility of intervention to optimize the energy efficiency. The optimization of control parameters is usually achieved only with great experience and knowledge. There are any tools which facilitate an objective comparison of optimization measures of control concepts, strategies and settings. In order to facilitate the evaluation and comparison of refrigeration controls, a hardware-in-the-loop test environment was set up at the University of Applied Sciences in Biberach (Federal Republic of Germany). The test environment facilitates an implementation of a controller in a simulation environment so that the controller drives the simulation model of the chiller. Due to this procedure, tests are possible under standardized and reproducible conditions. The impact of modified control parameters, disturbances and modifications in the regulatory approach can be investigated by means of the possibility of a targeted impacting of individual disturbances. The test rig was designed, built and tested at the University of Applied Sciences in Biberach. Simulation models were adapted to the

Air-deployable oil spill sampling devices review phase 2 testing. Volume 1

International Nuclear Information System (INIS)

Hawke, L.; Dumouchel, A.; Fingas, M.; Brown, C.E.

2007-01-01

SAIC Canada tested air deployable oil sampling devices for the Emergencies Science and Technology Division of Environment Canada in order to determine the applicability and status of these devices. The 3 devices tested were: Canada's SABER (sampling autonomous buoy for evidence recovery), the United States' POPEIE (probe for oil pollution evidence in the environment); and, Sweden's SAR Floatation 2000. They were tested for buoyancy properties, drift behaviour and sampler sorbent pickup ratios. The SAR and SABER both had lesser draft and greater freeboard, while the POPEIE had much greater draft than freeboard. All 3 devices could be used for oil sample collection in that their drift characteristics would allow for the SABER and SAR devices to be placed upwind of the slick while the POPEIE device could be placed downwind of an oil spill. The sorbent testing revealed that Sefar sorbent and Spectra sorbent used in the 3 devices had negative pickup ratios for diesel but performance improved as oil viscosity increased. Both sorbents are inert and capable of collecting oil in sufficient volumes for consistent fingerprinting analysis. 10 refs., 8 tabs., 8 figs

Wavefront division digital holography

Science.gov (United States)

Zhang, Wenhui; Cao, Liangcai; Li, Rujia; Zhang, Hua; Zhang, Hao; Jiang, Qiang; Jin, Guofan

2018-05-01

Digital holography (DH), mostly Mach-Zehnder configuration based, belongs to non-common path amplitude splitting interference imaging whose stability and fringe contrast are environmental sensitive. This paper presents a wavefront division DH configuration with both high stability and high-contrast fringes benefitting from quasi common path wavefront-splitting interference. In our proposal, two spherical waves with similar curvature coming from the same wavefront are used, which makes full use of the physical sampling capacity of the detectors. The interference fringe spacing can be adjusted flexibly for both in-line and off-axis mode due to the independent modulation to these two waves. Only a few optical elements, including the mirror-beam splitter interference component, are used without strict alignments, which makes it robust and easy-to-implement. The proposed wavefront division DH promotes interference imaging physics into the practical and miniaturized a step forward. The feasibility of this method is proved by the imaging of a resolution target and a water flea.

Chemical and Laser Sciences Division: Annual report, 1987

International Nuclear Information System (INIS)

1988-01-01

As the Chemical and Laser Sciences Division concludes its first year, the Division personnel can be proud of their many scientific and technical accomplishments. Among the important milestones which the Division achieved were significant demonstrations of the process performance in the Special Isotope Separation program, of beam sensing techniques for the NPB program, and of optical angular multiplexing and energy extraction from the ICF KrF laser. In addition, the Los Alamos FTS was brought to operational status and the Bright Source attained intensities on the order of 10 17 W/cm 2 . A few highlights of these and other research and development activities are presented in the following sections of this report