WorldWideScience

Sample records for environment monitor sem

  1. Secondary emission monitor (SEM) grids.

    CERN Multimedia

    Patrice Loïez

    2002-01-01

    A great variety of Secondary Emission Monitors (SEM) are used all over the PS Complex. At other accelerators they are also called wire-grids, harps, etc. They are used to measure beam density profiles (from which beam size and emittance can be derived) in single-pass locations (not on circulating beams). Top left: two individual wire-planes. Top right: a combination of a horizontal and a vertical wire plane. Bottom left: a ribbon grid in its frame, with connecting wires. Bottom right: a SEM-grid with its insertion/retraction mechanism.

  2. The influence of environment temperature on SEM image quality

    International Nuclear Information System (INIS)

    Chen, Li; Liu, Junshan

    2015-01-01

    As the structure dimension goes down to the nano-scale, it often requires a scanning electron microscope (SEM) to provide image magnification up to 100 000  ×. However, SEM images at such a high magnification usually suffer from high resolution value and low signal-to-noise ratio, which results in low quality of the SEM image. In this paper, the quality of the SEM image is improved by optimizing the environment temperature. The experimental results indicate that at 100 000  ×, the quality of the SEM image is influenced by the environment temperature, whereas at 50 000  × it is not. At 100 000  × the best SEM image quality can be achieved from the environment temperature ranging 292 from 294 K, and the SEM image quality evaluated by the double stimulus continuous quality scale method can increase from grade 1 to grade 5. It is expected that this image quality improving method can be used in routine measurements with ordinary SEMs to get high quality images by optimizing the environment temperature. (paper)

  3. Tillandsia stricta Sol (Bromeliaceae) leaves as monitors of airborne particulate matter-A comparative SEM methods evaluation: Unveiling an accurate and odd HP-SEM method.

    Science.gov (United States)

    de Oliveira, Martha Lima; de Melo, Edésio José Tenório; Miguens, Flávio Costa

    2016-09-01

    Airborne particulate matter (PM) has been included among the most important air pollutants by governmental environment agencies and academy researchers. The use of terrestrial plants for monitoring PM has been widely accepted, particularly when it is coupled with SEM/EDS. Herein, Tillandsia stricta leaves were used as monitors of PM, focusing on a comparative evaluation of Environmental SEM (ESEM) and High-Pressure SEM (HPSEM). In addition, specimens air-dried at formaldehyde atmosphere (AD/FA) were introduced as an SEM procedure. Hydrated specimen observation by ESEM was the best way to get information from T. stricta leaves. If any artifacts were introduced by AD/FA, they were indiscernible from those caused by CPD. Leaf anatomy was always well preserved. PM density was determined on adaxial and abaxial leaf epidermis for each of the SEM proceedings. When compared with ESEM, particle extraction varied from 0 to 20% in air-dried leaves while 23-78% of particles deposited on leaves surfaces were extracted by CPD procedures. ESEM was obviously the best choice over other methods but morphological artifacts increased in function of operation time while HPSEM operation time was without limit. AD/FA avoided the shrinkage observed in the air-dried leaves and particle extraction was low when compared with CPD. Structural and particle density results suggest AD/FA as an important methodological approach to air pollution biomonitoring that can be widely used in all electron microscopy labs. Otherwise, previous PM assessments using terrestrial plants as biomonitors and performed by conventional SEM could have underestimated airborne particulate matter concentration. © 2016 Wiley Periodicals, Inc.

  4. Low Cost Environmental Sensors for Spaceflight: NMP Space Environmental Monitor (SEM) Requirements

    Science.gov (United States)

    Garrett, Henry B.; Buehler, Martin G.; Brinza, D.; Patel, J. U.

    2005-01-01

    An outstanding problem in spaceflight is the lack of adequate sensors for monitoring the space environment and its effects on engineering systems. By adequate, we mean low cost in terms of mission impact (e.g., low price, low mass/size, low power, low data rate, and low design impact). The New Millennium Program (NMP) is investigating the development of such a low-cost Space Environmental Monitor (SEM) package for inclusion on its technology validation flights. This effort follows from the need by NMP to characterize the space environment during testing so that potential users can extrapolate the test results to end-use conditions. The immediate objective of this effort is to develop a small diagnostic sensor package that could be obtained from commercial sources. Environments being considered are: contamination, atomic oxygen, ionizing radiation, cosmic radiation, EMI, and temperature. This talk describes the requirements and rational for selecting these environments and reviews a preliminary design that includes a micro-controller data logger with data storage and interfaces to the sensors and spacecraft. If successful, such a sensor package could be the basis of a unique, long term program for monitoring the effects of the space environment on spacecraft systems.

  5. Monitoring of environment

    Energy Technology Data Exchange (ETDEWEB)

    Mitsudera, M

    1974-09-01

    The amount of pollutants discharged has now exceeded the environment's natural ability to purify itself. The effect of urbanization is traced especially the degeneration of plants and animals in Tokyo. One of the methods of monitoring plants is remote sensing with multi-band photography and multi-spectroscanning. There is a correlation between the sulfur content of tree leaves and multi-band photograms on red pine trees with a correlation coefficient of -0.862.

  6. The advancement of the built environment research through employment of structural equation modeling (SEM)

    Science.gov (United States)

    Wasilah, S.; Fahmyddin, T.

    2018-03-01

    The employment of structural equation modeling (SEM) in research has taken an increasing attention in among researchers in built environment. There is a gap to understand the attributes, application, and importance of this approach in data analysis in built environment study. This paper intends to provide fundamental comprehension of SEM method in data analysis, unveiling attributes, employment and significance and bestow cases to assess associations amongst variables and constructs. The study uses some main literature to grasp the essence of SEM regarding with built environment research. The better acknowledgment of this analytical tool may assist the researcher in the built environment to analyze data under complex research questions and to test multivariate models in a single study.

  7. Environment monitoring from space

    International Nuclear Information System (INIS)

    Takagi, M.

    1994-01-01

    Environmental problems such as acid rain, ozone depletion, deforestation, erosion, and the greenhouse effect are of increasing concern, and continuous earth observation from artificial satellites has been contributing significant information on the environment since the 1960s. Earth observation from space has the advantages of wide area coverage at potentially high resolutions, periodic and long-term observation capability, data acquisition with uniform quality and repeatability, and ability to observe using different types of sensors. Problems to be solved in earth observation include the need for preprocessing of satellite data, understanding the relationship between observed physical parameters and objects, and the high volume of data for processing. In Japan, a research project on the higher-order utilization of remote sensing data from space was organized in 1985, and the results led to recognition of the importance of satellite observation. It was then decided to undertake a program to improve the understanding of the earth environment by satellite. Five research plans were selected: a basic study on earth observation by microwaves; global change analysis of the biosphere; a study of the physical process of the water cycle over land; a study of air-sea interaction; and higher-order processing of earth observation information. In recognition of the international nature of satellite data, as well as the capabilities of Canada and Japan in computer, communication, and multimedia technologies, bilateral cooperation is proposed in the area of earth environment information systems based on satellite observation

  8. Enhanced defect of interest [DOI] monitoring by utilizing sensitive inspection and ADRTrue SEM review

    Science.gov (United States)

    Kirsch, Remo; Zeiske, Ulrich; Shabtay, Saar; Beyer, Mirko; Yerushalmi, Liran; Goshen, Oren

    2011-03-01

    As semiconductor process design rules continue to shrink, the ability of optical inspection tools to separate between true defects and nuisance becomes more and more difficult. Therefore, monitoring Defect of Interest (DOI) become a real challenge (Figure 1). This phenomenon occurs due to the lower signal received from real defects while noise levels remain almost the same, resulting in inspection high nuisance rate, which jeopardizes the ability to provide a meaningful, true defect Pareto. A non-representative defect Pareto creates a real challenge to a reliable process monitoring (Figure 4). Traditionally, inspection tool recipes were optimized to keep data load at a manageable level and provide defect maps with ~10% nuisance rate, but as defects of interest get smaller with design rule shrinkage, this requirement results in a painful compromise in detection sensitivity. The inspection is usually followed by defect review and classification using scanning electron microscope (SEM), the classification done manually and it is performed on a small sample of the inspection defect map due to time and manual resources limitations. Sample is usually 50~60 randomly selected locations, review is performed manually most of the times, and manual classification is performed for all the reviewed locations. In the approach described in this paper, the inspection tool recipe is optimized for sensitivity rather than low nuisance rate (i.e. detect all DOI with compromising on a higher nuisance rate). Inspection results with high nuisance rate introduce new challenges for SEM review methodology & tools. This paper describe a new approach which enhances process monitoring quality and the results of collaborative work of the Process Diagnostic & Control Business Unit of Applied Materials® and GLOBALFOUNDRIES® utilizing Applied Materials ADRTrueTM & SEMVisionTM capabilities. The study shows that the new approach reveals new defect types in the Pareto, and improves the ability to

  9. Establishing aeolian particulate 'fingerprints' in an airport environment using magnetic measurements and SEM/EDAX

    Science.gov (United States)

    Jones, Sue; Hoon, Stephen R.; Richardson, Nigel; Bennett, Michael

    2016-04-01

    The significant increase in global air travel which has occurred during the last fifty years has generated growing concern regarding the potential impacts associated with increasing emissions of particulate matter (PM) from aviation activity on health and the environment. PM within the airport environment, in particular, may be derived from a wide range of potential sources including aircraft; vehicles; ground support equipment and buildings. In order to investigate and remediate potential problem sources, it is important to be able to identify characteristic particulate 'fingerprints' which would allow source attribution, particularly respirable particulates. To date the identification of such 'fingerprints' has remained elusive but remains a key research priority for the aviation industry (Webb et al, 2008). In previous PM studies, environmental magnetism has been used as a successful technique for discriminating between different emission types and particulate sources in both urban and industrial environments (e.g. Hunt et al 1984; Lecoanet et al 2003, Jones et al 2015). Environmental magnetism is a non-destructive and relatively rapid technique involving the use of non-directional, rock magnetic measurements to characterise the mineral magnetic properties of natural and anthropogenic materials. In other studies scanning electron microscopy (SEM) has also been used as an effective characterisation technique for the investigation of grain size and morphology of PM derived from vehicle emissions (e.g. Bucko et al 2010) and fossil fuel combustion sources (Kim et al 2009). In this study, environmental magnetic measurements and SEM/EDAX have been used to characterise dusts from specific aircraft sources including engines, brakes and tyres. Furthermore, these methods have also been applied to runway (both hard and grass covered surfaces), taxiway and apron dusts collected during extensive environmental sampling at Manchester International Airport, UK in order to

  10. Vision-Based Haptic Feedback for Remote Micromanipulation in-SEM Environment

    Science.gov (United States)

    Bolopion, Aude; Dahmen, Christian; Stolle, Christian; Haliyo, Sinan; Régnier, Stéphane; Fatikow, Sergej

    2012-07-01

    This article presents an intuitive environment for remote micromanipulation composed of both haptic feedback and virtual reconstruction of the scene. To enable nonexpert users to perform complex teleoperated micromanipulation tasks, it is of utmost importance to provide them with information about the 3-D relative positions of the objects and the tools. Haptic feedback is an intuitive way to transmit such information. Since position sensors are not available at this scale, visual feedback is used to derive information about the scene. In this work, three different techniques are implemented, evaluated, and compared to derive the object positions from scanning electron microscope images. The modified correlation matching with generated template algorithm is accurate and provides reliable detection of objects. To track the tool, a marker-based approach is chosen since fast detection is required for stable haptic feedback. Information derived from these algorithms is used to propose an intuitive remote manipulation system that enables users situated in geographically distant sites to benefit from specific equipments, such as SEMs. Stability of the haptic feedback is ensured by the minimization of the delays, the computational efficiency of vision algorithms, and the proper tuning of the haptic coupling. Virtual guides are proposed to avoid any involuntary collisions between the tool and the objects. This approach is validated by a teleoperation involving melamine microspheres with a diameter of less than 2 μ m between Paris, France and Oldenburg, Germany.

  11. Morphological and Production Changes in Stressed Red Yeasts Monitored Using SEM and Raman Spectroscopy

    Czech Academy of Sciences Publication Activity Database

    Hrubanová, Kamila; Samek, Ota; Haroniková, A.; Bernatová, Silvie; Zemánek, Pavel; Márová, I.; Krzyžánek, Vladislav

    2016-01-01

    Roč. 22, S3 (2016), s. 1146-1147 ISSN 1431-9276 R&D Projects: GA MŠk(CZ) LO1212; GA MŠk ED0017/01/01; GA ČR(CZ) GA14-20012S; GA ČR(CZ) GA15-20645S Institutional support: RVO:68081731 Keywords : SEM * Raman spectroscopy Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.891, year: 2016

  12. Monitoring of Multilayered Bacterial Biofilm Morphology by Cryo-SEM for Raman Spectroscopy Measurements

    Czech Academy of Sciences Publication Activity Database

    Hrubanová, Kamila; Bernatová, Silvie; Samek, Ota; Šerý, Mojmír; Zemánek, Pavel; Nebesářová, Jana; Růžička, F.; Krzyžánek, Vladislav

    2015-01-01

    Roč. 21, S3 (2015), s. 187-188 ISSN 1431-9276 R&D Projects: GA MŠk(CZ) LO1212; GA MŠk ED0017/01/01; GA ČR(CZ) GA14-20012S Institutional support: RVO:68081731 ; RVO:60077344 Keywords : multilayered bacterial biofilm * morphology by Cryo-SEM * Raman spectroscopy Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.730, year: 2015

  13. Environment quality monitoring using ARM processor

    Science.gov (United States)

    Vinaya, C. H.; Krishna Thanikanti, Vamsi; Ramasamy, Sudha

    2017-11-01

    This paper of air quality monitoring system describes a model of sensors network to continuously monitoring the environment with low cost developed model. At present time all over the world turned into a great revolution in industrial domain and on the other hand environment get polluting in a dangerous value. There are so many technologies present to reduce the polluting contents but still there is no completely reduction of that pollution. Even there are different methods to monitor the pollution content; these are much costly that not everyone can adapt those methods or devices. Now we are proposing a sensors connected network to monitor the environment continuously and displaying the pollutant gases percentage in air surroundings and can transmit the results to our mobiles by message. The advantage of this system is easy to design, establish at area to monitor, maintenance and most cost effective as well.

  14. Monitoring of radioactivity in the environment 201

    International Nuclear Information System (INIS)

    Moeller, B.; Dyve, J.E.; Tazmini, K.

    2013-01-01

    The Report summarizes the data from Norwegian Radiation Protection Authority and The Norwegian Civil Defence monitoring programs for radioactivity in the environment in 2011. A short description of the systems is also presented.(Author)

  15. Morphological and Production Changes in Planktonic and Biofilm Cells Monitored Using SEM and Raman Spectroscopy

    Czech Academy of Sciences Publication Activity Database

    Hrubanová, Kamila; Krzyžánek, Vladislav; Samek, Ota; Skoupý, Radim; Šiler, Martin; Ježek, Jan; Obruča, S.; Zemánek, Pavel

    2017-01-01

    Roč. 23, S1 (2017), s. 1158-1159 ISSN 1431-9276 R&D Projects: GA ČR(CZ) GA15-20645S; GA ČR(CZ) GA16-12477S; GA ČR(CZ) GA17-15451S; GA MŠk(CZ) LO1212; GA MŠk ED0017/01/01 Institutional support: RVO:68081731 Keywords : biofilm cells * SEM * Raman spectroscopy Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering OBOR OECD: Electrical and electronic engineering Impact factor: 1.891, year: 2016

  16. The monitoring of radioactivity in the environment

    International Nuclear Information System (INIS)

    1986-01-01

    35 separately indexed lectures are discussed of this conference. The contents of the individual contributions cover the following areas: 1) Monitoring networks and guidelines; 2) Monitoring equipment and methods; 3) Development of models for radionuclide migration, and 4) Individual determination and analysis of radionuclides relevant to the environment. (PW) [de

  17. Microplastics Monitoring in Marine Environment

    Directory of Open Access Journals (Sweden)

    Agung Dhamar Syakti

    2017-11-01

    Full Text Available This review summarizes the need for future spatiotemporal comparisons of microplastic abundance across marine environment, through standardized methods for microplastic sampling and analysis in sea water, beach and seabed sediment and marine organism. Pretreatment of the sample prior to the elimination of organic matter should be done using appropriate reagents was also described. Extraction of microplastics from environmental matrices is based on the different density of targeted microplastics with saturated salt solutions (NaCl, NaI, CaCl2, ZnCl2 and lithium metatungstate. Quantification can be achieved by microscopic techniques (binocular, stereomicroscope, fluorescence microscope and scanning electron microscope and discussion on identification methods including FTIR, Pyr-GC/MS and Raman spectroscopy will be provided. This review also endorses the importance of further study regarding the fate and impact of microplastics on marine biota and human health, especially when we acknowledge that co-pollution may occur during the transport on microplastic in marine environment.

  18. Guidelines for radiological monitoring of the environment

    International Nuclear Information System (INIS)

    1990-11-01

    This Standard provides criteria to be used in deciding whether an environmental monitoring program is required for a given nuclear facility. It also sets out a systematic approach to monitoring the environment, which is considered to be outside the facility boundary. It provides guidelines for establishing an environmental program covering sampling and analysis protocols, analytical techniques and sensitivity, statistical treatment of monitoring results, quality assurance, methods for expressing results, and record keeping. The standard applies to the environment of a nuclear facility operating mainly under normal conditions; in addition, certain of these requirements may also apply to situations involving abnormal releases

  19. Monitoring the Environments We Depend On

    International Nuclear Information System (INIS)

    Madsen, Michael

    2013-01-01

    Our overuse of natural resources, pollution and climate change are weakening natural systems’ ability to adapt to ever more sources of stress. The varied environments of our planet are interconnected and the pollution of one has ramifications across all. It is thus important to monitor the health of our environment to ensure a sustainable future. The IAEA, through its Environment Laboratories, Water Resource Programme, and technical cooperation programme, applies unique, versatile and cost-effective isotopic and nuclear techniques to understand many of the key environmental mechanisms needed to ensure a sustainable future. These monitoring systems help Member States make ecologically-responsible and scientifically-grounded development decisions

  20. Modelling Mathematics Teachers' Intention to Use the Dynamic Geometry Environments in Macau: An SEM Approach

    Science.gov (United States)

    Zhou, Mingming; Chan, Kan Kan; Teo, Timothy

    2016-01-01

    Dynamic geometry environments (DGEs) provide computer-based environments to construct and manipulate geometric figures with great ease. Research has shown that DGEs has positive impact on student motivation, engagement, and achievement in mathematics learning. However, the adoption of DGEs by mathematics teachers varies substantially worldwide.…

  1. Soil monitoring as a part of environment monitoring in Slovakia

    International Nuclear Information System (INIS)

    Kobza, J.

    1997-01-01

    In frame of Soil monitoring system it is going about a lot of methods in advance as follows: methods of soil monitoring sites selection and soil monitoring network construction, as well; methods of soil survey and soil sampling; analytical methods (indicating of chemical, agrochemical and physical properties); soil database and methods of evaluation and interpretation of measured results. The monitoring network was constructed on the base of ecological principles - including the monitoring of all soil types and subtypes, various climatic and emission regions as well as relatively clean regions, lowland and highland. Soil monitoring network in forest land is regular (8 x 8 km) with regard to International monitoring system in Forestry. The soil monitoring network in Slovakia consist of 650 monitoring sites (312 sites in farming land and 338 sites in forest land). In addition soil monitoring network includes also 21 monitoring sites. All monitoring sites are geodesically located and reported on the map at a scale of 1:5000. There are the methods concerning the important soil parameters indication with regard to main soil degradation processes a s follows: soil contamination (heavy metals and organic contaminants); soil acidification; soil salinity; soil erosion (deluometrically by the Cs-137 and remote sensing methods); soil compaction; soil fertility and protection. Analytical control system was elaborated according to Good Laboratory Practice. Evaluation of soil monitoring network results is not simple because it depends on various monitored parameters, on aim of evaluation as well as on the scale of landscape which is object for evaluation. There are used the modern statistical methods in monitoring system which can be: universal; disjunctive; simulated. Used statistical methods are significant for interpretation of measured results as follows: trends in landscape; anisotropy; comparison. The evaluation and interpretation way is very significant with regard not

  2. Designing a Secure Exam Management System (SEMS) for M-Learning Environments

    Science.gov (United States)

    Kaiiali, Mustafa; Ozkaya, Armagan; Altun, Halis; Haddad, Hatem; Alier, Marc

    2016-01-01

    M-learning has enhanced the e-learning by making the learning process learner-centered. However, enforcing exam security in open environments where each student has his/her own mobile/tablet device connected to a Wi-Fi network through which it is further connected to the Internet can be one of the most challenging tasks. In such environments,…

  3. The near coastal environment monitored from space

    International Nuclear Information System (INIS)

    Szekielda, K.H.

    1977-01-01

    The optical information required for monitoring the marine environment from space is discussed and applied for the near coastal area. By categorizing coastal features it is possible to recognize coastal regions to a high degree and to indentify water masses derived from land sources and sewage dumping sites. It is concluded that monitoring from space can be used as a tool in environmental planning. (orig.) [de

  4. Employee quality, monitoring environment and internal control

    OpenAIRE

    Chunli Liu; Bin Lin; Wei Shu

    2017-01-01

    We investigate the effect of internal control employees (ICEs) on internal control quality. Using special survey data from Chinese listed firms, we find that ICE quality has a significant positive influence on internal control quality. We examine the effect of monitoring on this result and find that the effect is more pronounced for firms with strict monitoring environments, especially when the firms implement the Chinese internal control regulation system (CSOX), have higher institutional ow...

  5. Cryo-Scanning Electron Microscopy (SEM) and Scanning Transmission Electron Microscopy (STEM)-in-SEM for Bio- and Organo-Mineral Interface Characterization in the Environment.

    Science.gov (United States)

    Wille, Guillaume; Hellal, Jennifer; Ollivier, Patrick; Richard, Annie; Burel, Agnes; Jolly, Louis; Crampon, Marc; Michel, Caroline

    2017-12-01

    Understanding biofilm interactions with surrounding substratum and pollutants/particles can benefit from the application of existing microscopy tools. Using the example of biofilm interactions with zero-valent iron nanoparticles (nZVI), this study aims to apply various approaches in biofilm preparation and labeling for fluorescent or electron microscopy and energy dispersive X-ray spectrometry (EDS) microanalysis for accurate observations. According to the targeted microscopy method, biofilms were sampled as flocs or attached biofilm, submitted to labeling using 4',6-diamidino-2-phenylindol, lectins PNA and ConA coupled to fluorescent dye or gold nanoparticles, and prepared for observation (fixation, cross-section, freezing, ultramicrotomy). Fluorescent microscopy revealed that nZVI were embedded in the biofilm structure as aggregates but the resolution was insufficient to observe individual nZVI. Cryo-scanning electron microscopy (SEM) observations showed nZVI aggregates close to bacteria, but it was not possible to confirm direct interactions between nZVI and cell membranes. Scanning transmission electron microscopy in the SEM (STEM-in-SEM) showed that nZVI aggregates could enter the biofilm to a depth of 7-11 µm. Bacteria were surrounded by a ring of extracellular polymeric substances (EPS) preventing direct nZVI/membrane interactions. STEM/EDS mapping revealed a co-localization of nZVI aggregates with lectins suggesting a potential role of EPS in nZVI embedding. Thus, the combination of divergent microscopy approaches is a good approach to better understand and characterize biofilm/metal interactions.

  6. Platinum 'opal eyes' - an upgraded high resolution imaging standard for performance monitoring of FEG SEM and FEG VPSEM

    International Nuclear Information System (INIS)

    Griffin, B.J.

    2003-01-01

    Full text: The new generation of field emission variable pressure and conventional scanning electron microscopes [FEG (VP)SEM] are capable of extremely high resolution (e.g. 1nm 15kV) and, in parallel, imaging at very low accelerating voltages (e.g. 4 nm 0.1 kV). Most of this level of performance is in conventional high vacuum modes of operation, the variable pressure performances are lower but under rapid development. A synthetic opal sample with fine gold decoration on the 400nm silica spheres was described previously as a suitable standard for the routine monitoring of SEM performance. The sample was named 'OPAL EYES'. Whilst ideal for tungsten and LaBo filament sourced SEMs the level of detail was marginal for field emission SEM performance measurement for two reasons. Firstly, the fine gold decoration was highly variable in grain size and inconsistent between samples making comparable image collection difficult. Secondly the sample was prone to self-contamination and damage during imaging at high accelerating voltages or high magnifications. Overall the 'OPAL EYES' sample has been successful in its adoption by a number of service engineers and laboratories world-wide. A new processing step has been added to the previously described preparation process for the OPAL-EYES standard; a light sputter coating with platinum. The effect is dramatic and results in growth of (presumably -to be checked and reported on) Au-Pt features of remarkably consistent size within the central EYE regions of the sample. These outgrowths are proud of the substrate and often equi-dimensional at a size of ∼ 10 nm. The substrate detail is at a scale of ∼2-3 nm. The new Pt OPAL EYES have been used as a resolution test specimen on a recently installed FEG VPSEM with excellent results. An important feature of this new sample is the high contrast sharp-edged nature of the detail as this not only allows resolution measurement but also definition of interference (vibration, electric fields

  7. TIROS-N/NOAA A-J space environment monitor subsystem. Technical memo

    International Nuclear Information System (INIS)

    Seale, R.A.; Bushnell, R.H.

    1987-04-01

    The Space Environment Monitor (SEM), which is incorporated as a subsystem in the TIROS-N and NOAA A-J satellites, is described. The SEM consists of a Total Energy Detector (TED), a Medium Energy Proton and Electron Detector (MEPED), a High Energy Proton and Alpha Detector (HEPAD) and a Data Processing Unit (DPU). The detectors are intended to provide near-real-time particle data for use in the Space Environment Service Center of National Oceanic and Atmospheric Administration (NOAA) and to provide a long-term scientific data base. Telemeter codes, data reduction, and test instructions are given

  8. Tethered Contactless Mobile Nuclear Environment Monitoring Robot

    International Nuclear Information System (INIS)

    Choi, S. Y.; Lee, E. S.; Lee, Kun J.; Kim, Su H.; Rim, C. T.

    2013-01-01

    In fact, the nuclear environment monitoring is significantly crucial for early detection of NPP accident, radiological emergency, the estimation of radiation exposure to nearby residents as well as the long term radioactivity. In the UAE, the nuclear environment monitoring is, however, quite challenging because sampling locations are far from NPPs and the outdoor temperature and humidity are very high for NPP workers to collect soil, air, and water samples. Therefore, nuclear environment monitoring robots (Nubos) are strongly needed for the NPPs in the UAE. The Nubos can be remotely controlled to collect samples in extreme environment instead of NPP workers. Moreover, the Nubos can be unmanned ground vehicles (UGVs), unmanned aerial vehicles (UAVs) and unmanned marine vehicles (UMVs) to collect soil, air, and water samples, respectively. In this paper, the prototype development of UGV type Nubos using power cable for a long distance power delivery, called Tethered contactless mobile Nubo is introduced and validated by experiments. In this paper, the prototype development of Tethered Contactless Mobile (TeCoM) Nubo, which can be powered continuously within several km distance and avoid tangled cable, and the indoor test are finished. As further works, outdoor demonstration and a grand scale R and D proposal of practical Nubo will be proceeded

  9. Tethered Contactless Mobile Nuclear Environment Monitoring Robot

    Energy Technology Data Exchange (ETDEWEB)

    Choi, S. Y.; Lee, E. S.; Lee, Kun J.; Kim, Su H.; Rim, C. T. [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

    2013-05-15

    In fact, the nuclear environment monitoring is significantly crucial for early detection of NPP accident, radiological emergency, the estimation of radiation exposure to nearby residents as well as the long term radioactivity. In the UAE, the nuclear environment monitoring is, however, quite challenging because sampling locations are far from NPPs and the outdoor temperature and humidity are very high for NPP workers to collect soil, air, and water samples. Therefore, nuclear environment monitoring robots (Nubos) are strongly needed for the NPPs in the UAE. The Nubos can be remotely controlled to collect samples in extreme environment instead of NPP workers. Moreover, the Nubos can be unmanned ground vehicles (UGVs), unmanned aerial vehicles (UAVs) and unmanned marine vehicles (UMVs) to collect soil, air, and water samples, respectively. In this paper, the prototype development of UGV type Nubos using power cable for a long distance power delivery, called Tethered contactless mobile Nubo is introduced and validated by experiments. In this paper, the prototype development of Tethered Contactless Mobile (TeCoM) Nubo, which can be powered continuously within several km distance and avoid tangled cable, and the indoor test are finished. As further works, outdoor demonstration and a grand scale R and D proposal of practical Nubo will be proceeded.

  10. Employee quality, monitoring environment and internal control

    Directory of Open Access Journals (Sweden)

    Chunli Liu

    2017-03-01

    Full Text Available We investigate the effect of internal control employees (ICEs on internal control quality. Using special survey data from Chinese listed firms, we find that ICE quality has a significant positive influence on internal control quality. We examine the effect of monitoring on this result and find that the effect is more pronounced for firms with strict monitoring environments, especially when the firms implement the Chinese internal control regulation system (CSOX, have higher institutional ownership or attach greater importance to internal control. Our findings suggest that ICEs play an important role in the design and implementation of internal control systems. Our study should be of interest to both top managers who wish to improve corporate internal control quality and regulators who wish to understand the mechanisms of internal control monitoring.

  11. Monitoring product safety in the postmarketing environment.

    Science.gov (United States)

    Sharrar, Robert G; Dieck, Gretchen S

    2013-10-01

    The safety profile of a medicinal product may change in the postmarketing environment. Safety issues not identified in clinical development may be seen and need to be evaluated. Methods of evaluating spontaneous adverse experience reports and identifying new safety risks include a review of individual reports, a review of a frequency distribution of a list of the adverse experiences, the development and analysis of a case series, and various ways of examining the database for signals of disproportionality, which may suggest a possible association. Regulatory agencies monitor product safety through a variety of mechanisms including signal detection of the adverse experience safety reports in databases and by requiring and monitoring risk management plans, periodic safety update reports and postauthorization safety studies. The United States Food and Drug Administration is working with public, academic and private entities to develop methods for using large electronic databases to actively monitor product safety. Important identified risks will have to be evaluated through observational studies and registries.

  12. Wireless sensor network and monitoring for environment

    OpenAIRE

    Han, Liang

    2011-01-01

    In recent years, wireless sensor network technology is developing at a surprisingly high speed. More and more fields have started to use the wireless sensor network technology and find the advantages of WSN, such as military applications, environmental observing and forecasting system, medical care, smart home, structure monitoring. The world Environmental Summit in Copenhagen on 2010 has just concluded that environment has become the world’s main concern. But regrettably the summit did no...

  13. Radioactivity Monitoring of the Irish Environment 2006

    International Nuclear Information System (INIS)

    Smith, V.; Dowdall, A; Fegan, M.; Hayden, E.; Kelleher, K.; Long, S.; McEvoy, I.; Somerville, S.; Wong, J.; Pollard, D.

    2007-10-01

    This report presents the results of the environmental radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland (RPII) in 2006. This programme aims to assess the exposure of the Irish population to artificial radioactivity in the environment, to review the temporal and geographical distribution of contaminating radionuclides and to maintain systems and procedures which would allow a rapid assessment of environmental contamination to be made in the event of a radiological emergency. Radioactivity is present in the environment due to natural processes, the testing of nuclear weapons in the atmosphere, past nuclear accidents such as that at Chernobyl in Ukraine and the routine discharge of radionuclides from nuclear installations. Liquid discharges from the British Nuclear Group reprocessing plant at Sellafield in Cumbria in the north-west of England, which are licensed by the UK Environment Agency, continue to be the dominant source of artificial radioactivity in the Irish marine environment. The key elements of the monitoring programme implemented by the RPII in 2006 included; assessment of ambient radioactivity based on measurements of radioactivity in air and of external gamma dose rate at permanent monitoring stations located throughout the country; assessment of levels of radioactivity in drinking water; assessment of levels of radioactivity in foodstuffs based on measurements of total diet, milk and various ingredients; assessment of levels of radioactivity in the Irish marine environment based on sampling and measurement of seawater, sediment, seaweed, fish and shellfish. The RPII monitored airborne radioactivity at ten stations located throughout the country. One of these stations is equipped with a high volume sampler, which allows concentrations of caesium-137 to be measured; another is equipped to detect the presence of the gas krypton-85. This gas is released into the environment primarily as a result of the

  14. Chapter 7. Monitoring of chemical contamination of the environment and analytical-chemical monitoring

    International Nuclear Information System (INIS)

    Sojak, L.

    2006-01-01

    This chapter deals with the monitoring of chemical contamination of the environment and analytical-chemical monitoring. There are presented: the concept o monitoring of the environment of the Slovak Republic; unified monitoring system and complex information about state and development of the environment; analytical methods determination of chemical contaminants in the environment

  15. Radioactivity Monitoring of the Irish Environment 2007

    International Nuclear Information System (INIS)

    Fegan, M.; Dowdall, A.; Hanley, O.; Hayden, E.; Kelleher, K.; Long, S.; Smith, V.; Somerville, S.; Wong, J.; Pollard, D.

    2008-10-01

    This report presents the results of the environmental radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland (RPII) in 2007. This programme aims to assess the exposure of the Irish population to artificial radioactivity in the envorinment, to review the temporal and geographical distribution of contaminating radionuclides and to maintain systems and procedures which would allow a rapid assessment of environmental contamination to be made in the event of a radiological emergency. In additiopn, some natural radioactivity exposure pathways are included in the programme including radioactivity in surface and ground drinking water. Radioactivity is present in the environment due to natural oprocesses, the testing of nuclear weapons in the atmosphere, past nuclear accidents such as that at Chernobyl in the Ukraine and the routine discharge of radionuclides from nuclear installations. Liquid discharges from the British Nuclear Group reprocessing plant at Sellafield in Cumbria in the north-west of England continue to be the dominant source of artificial radioactivity in the Irish marine environment. The key elements of the monitoring programme implemented by the RPII in 2007 included; assessment of ambient radioactivity based on measurements of radioactivity in air and of external gamma dose rate at permanent monitoring stations located throughout the country; assessment of levels of radioactivity in drinking water; assessment of levels of radioactivity in foodstuffs based on measurements of total diet, milk and various ingredients; assessment of levels of radioactivity in the Irish marine environment based on sampling and measurement of seawater, sediment, seaweed, fish and shellfish. The RPII monitored airborne radioactivity at twelve stations located throughout the country. One of these stations is equipped with a high volume sampler, which allows background concentrations of caesium-137 to be measured; another is equipped to

  16. Radioactivity Monitoring of the Irish Environment 2009

    International Nuclear Information System (INIS)

    McGinnity, P.; Currivan, L.; Dowdall, A.; Fegan, M.; Hanley, O.; Kelleher, K.; McKittrick, L.; Somerville, S.; Wong, J.; Pollard, D.

    2010-12-01

    This report presents the results of the environmental radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland (RPII) during 2009. The RPII has routinely monitored levels of radioactivity in the environment since 1982 and this is the latest in the RPII's series of environmental monitoring reports. The RPII reviews and updates its environmental programme annually so as to ensure it remains relevant and continues to focus on the most important sources of radioactivity in the environment. The principal aims of the RPII's monitoring programme are; to assess the level of radioactivity to which the Irish population is exposed as a result of radioactivity in the environment; to study trends and establish the geographical distribution of contaminating radionuclides so as to better understand the long term behaviour of artificial radioactivity in the food chain and the environment; to ensure that any increase in radiation levels resulting from an accidental release of radioactivity to the environment is detected and assessed rapidly. During 2009 radioactivity was measured in a wide range of foods and environmental materials including: air, water, milk, seafood, foodstuffs and complete meals. The most significant source of artificial radioactivity in the Irish marine environment is the discharge of low level liquid radioactive waste from the Sellafield Nuclear Fuel Reprocessing Plant on the north east coast of England. In order to assess the exposure arising from the source extensive sampling of fish and shellfish landed at ports along the north east coast of Ireland is undertaken. The most exposed group of individuals to discharges from Sellafield have been identified as commercial oyster and mussel farmers working along the north east coastline and their families. Manmade radioactivity is also present in the terrestrial environment due primarily to residual global fallout arising primarily from atmospheric testing of nuclear

  17. Radioactivity Monitoring of the Irish Environment 2008

    International Nuclear Information System (INIS)

    Fegan, M.; Currivan, L.; Dowdall, A.; Hanley, O.; Hayden, E.; Kelleher, K.; Long, S.; McKittrick, L.; Somerville, S.; Wong, J.; Pollard, D.

    2010-01-01

    This report presents the results of the environmental radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland (RPII) during 2008. The RPII has routinely monitored levels of radioactivity in the environment since 1982 and this is the latest in the RPII's series of environmental monitoring reports. The RPII reviews and updates its environmental programme annually so as to ensure it remains relevant and continues to focus on the most important sources of radioactivity in the environment. The principal aims of the RPII's monitoring programme are; to assess the level of radioactivity to which the Irish population is exposed as a result of radioactivity in the environment; to study trends and establish the geographical distribution of contaminating radionuclides so as to better understand the long term behaviour of artificial radioactivity in the food chain and the environment; to ensure that any increase in radiation levels resulting from an accidental release of radioactivity to the environment is detected and assessed rapidly. During 2008 radioactivity was measured in a wide range of foods and environmental materials including: air, water, milk, seafood, foodstuffs and complete meals. The most significant source of artificial radioactivity in the Irish marine environment is the discharge of low level liquid radioactive waste from the Sellafield Nuclear Fuel Reprocessing Plant on the north east coast of England. In order to assess the exposure arising from the source extensive sampling of fish and shellfish landed at ports along the north east coast of Ireland is undertaken. The most exposed group of individuals to discharges from Sellafield have been identified as commercial oyster and mussel farmers working along the north east coastline and their families. Manmade radioactivity is also present in the terrestrial environment due primarily to residual global fallout arising primarily from atmospheric testing of nuclear

  18. SEM Anthology

    Science.gov (United States)

    Rodgers, Michelle; Zimar, Heather

    2004-01-01

    The "SEM Anthology" is a compilation of articles by more than 30 enrollment management professionals from a variety of institutions across the country. This collection, which has appeared in SEM Monthly over the past year, chronicles Strategic Enrollment Management efforts at campuses nationwide. The book illustrates the successes and challenges…

  19. MAFF monitoring of the terrestrial environment

    International Nuclear Information System (INIS)

    Sherlock, J.C.

    1991-01-01

    This paper addresses the MAFF food surveillance programme, in particular our Terrestrial Radioactivity Monitoring Programme (TRAMP), and the estimation of dietary intake of radionuclides. The MAFF programme exists primarily to demonstrate that authorized discharges of radioactivity to the environment do not result in individuals receiving doses of radiation in excess of accepted limits. The estimation radionuclide intake ensures over estimation rather than underestimation of dose. Improvements in detection limits and absorption level research could lower the calculated dose to man from radionuclides in food without losing their validity. (author)

  20. Monitoring of radioactivity in the marine environment

    International Nuclear Information System (INIS)

    Bologa, A.S.

    1992-01-01

    The necessity of radioactivity monitoring in the marine environment was imposed by the increasing development of nuclear power and its world-wide use in many different segments of economic and social life. Both natural and artificial radioactivity play an important role in marine ecology and human health. In this respect three major facts continue to prevail in Romania. The fallout, the presence of the Danube river and the expectations for future energy production. Spatial and temporal monitoring of marine radioactivity along the Romanian Black Sea shore has been systematically performed in the Romanian Marine Research Institute in close co-operation with the Institute of Meteorology and Hydrology since 1981. Marine emerged and submerged sediments, coastal and offshore sea water, macroalgae, in vertebrates and fish off the Danube mouths and/or along the coast are monitored for natural and artificial radioactivity by means of beta gross measurements and gamma spectrometry. Concentrations of radionuclides as K-40, Cs-134, Cs-137 in abiotic and biotic samples, environmental distributions coefficients and concentrations factors (CF), as well as experimentally-derived CFs in marine biota as radioecological bioindicators are assessed and stored for a national data base. (author) 3 tabs., 18 refs

  1. Radioactive monitoring of the marine environment

    International Nuclear Information System (INIS)

    Bologa, A. S.

    1991-01-01

    Radioactivity monitoring of marine environment was required by the development of nuclear power and the worldwide use of ionizing radiations in many different activities. Both natural and artificial radioactivity play an important role in marine ecology and human health. In respect of this, three major facts prevail, namely: the fallout, the proximity of Danube River and the future nuclear power production. Spatial and temporal monitoring of marine radioactivity along the Romanian Black Sea shore has been systematically performed in Romanian Marine Research Institute in close cooperation with Institute of Meteorology and Hydrology since 1981. Marine emerged and submerged sediments, coastal and offshore sea water, macroalgae, invertebrates and fish of Danube mouths and/or along the coast are monitored for natural and artificial radioactivity by means of gross beta measurements and gamma spectrometry. Concentrations of radionuclides such as: K-40, Cs-134 and Cs-137 in abiotic and biotic samples, environmental distribution coefficients and concentration factors (CFs) as well as experimentally derived CFs in marine biota as radioecological bioindicators are assessed and stored in a national data base. (author)

  2. The Global Environment Radiation Monitoring Network (GERMON)

    International Nuclear Information System (INIS)

    Zakheim, B.J.; Goellner, D.A.

    1994-01-01

    Following the Chernobyl accident in 1986, a group of experts from the World Health Organization (WHO) and the United Nations Environment Program (UNEP) met in France to discuss and develop the basic principles of a global environmental radiation monitoring network (GERMON). The basic functions of this network were to provide regular reports on environmental radiation levels and to be in a position to provide reliable and accurate radiation measurements on a quick and accurate radiation measurements on a quick turnaround basis in the event of a major radiation release. By 1992, although 58 countries had indicated an interest in becoming a part of the GERMON system, only 16 were providing data on a regular basis. This paper traces the history of GERMON from its inception in 1987 through its activities during 1993-4. It details the objectives of the network, describes functions, lists its participants, and presents obstacles in the current network. The paper examines the data requirements for radiological emergency preparedness and offers suggestions for the current system. The paper also describes the growing need for such a network. To add a domestic perspective, the authors present a summary of the environmental monitoring information system that was used by the NRC in 1986 in its analyses of the Chernobyl incident. Then we will use this 1986 experience to propose a method for the use of GERMON should a similar occasion arise in the future

  3. Advancing UAS methods for monitoring coastal environments

    Science.gov (United States)

    Ridge, J.; Seymour, A.; Rodriguez, A. B.; Dale, J.; Newton, E.; Johnston, D. W.

    2017-12-01

    Utilizing fixed-wing Unmanned Aircraft Systems (UAS), we are working to improve coastal monitoring by increasing the accuracy, precision, temporal resolution, and spatial coverage of habitat distribution maps. Generally, multirotor aircraft are preferred for precision imaging, but recent advances in fixed-wing technology have greatly increased their capabilities and application for fine-scale (decimeter-centimeter) measurements. Present mapping methods employed by North Carolina coastal managers involve expensive, time consuming and localized observation of coastal environments, which often lack the necessary frequency to make timely management decisions. For example, it has taken several decades to fully map oyster reefs along the NC coast, making it nearly impossible to track trends in oyster reef populations responding to harvesting pressure and water quality degradation. It is difficult for the state to employ manned flights for collecting aerial imagery to monitor intertidal oyster reefs, because flights are usually conducted after seasonal increases in turbidity. In addition, post-storm monitoring of coastal erosion from manned platforms is often conducted days after the event and collects oblique aerial photographs which are difficult to use for accurately measuring change. Here, we describe how fixed wing UAS and standard RGB sensors can be used to rapidly quantify and assess critical coastal habitats (e.g., barrier islands, oyster reefs, etc.), providing for increased temporal frequency to isolate long-term and event-driven (storms, harvesting) impacts. Furthermore, drone-based approaches can accurately image intertidal habitats as well as resolve information such as vegetation density and bathymetry from shallow submerged areas. We obtain UAS imagery of a barrier island and oyster reefs under ideal conditions (low tide, turbidity, and sun angle) to create high resolution (cm scale) maps and digital elevation models to assess habitat condition

  4. Distributed computing environment monitoring and user expectations

    International Nuclear Information System (INIS)

    Cottrell, R.L.A.; Logg, C.A.

    1996-01-01

    This paper discusses the growing needs for distributed system monitoring and compares it to current practices. It then goes to identify the components of distributed system monitoring and shows how they are implemented and successfully used at one site today to address the Local area Network (WAN), and host monitoring. It shows how this monitoring can be used to develop realistic service level expectations and also identifies the costs. Finally, the paper briefly discusses the future challenges in network monitoring. (author)

  5. Distributed computing environment monitoring and user expectations

    International Nuclear Information System (INIS)

    Cottrell, R.L.A.; Logg, C.A.

    1995-11-01

    This paper discusses the growing needs for distributed system monitoring and compares it to current practices. It then goes on to identify the components of distributed system monitoring and shows how they are implemented and successfully used at one site today to address the Local Area Network (LAN), network services and applications, the Wide Area Network (WAN), and host monitoring. It shows how this monitoring can be used to develop realistic service level expectations and also identifies the costs. Finally, the paper briefly discusses the future challenges in network monitoring

  6. Negotiation and Monitoring in Open Environments

    NARCIS (Netherlands)

    Clark, K.P.

    2014-01-01

    Large scale, distributed, digital environments offer vast potential. Within these environments, software systems will provide unprecedented support for daily life. Offering access to vast amounts of knowledge and resources, these systems will enable wider participation of society, at large. An

  7. The effects of monitoring environment on problem-solving performance.

    Science.gov (United States)

    Laird, Brian K; Bailey, Charles D; Hester, Kim

    2018-01-01

    While effective and efficient solving of everyday problems is important in business domains, little is known about the effects of workplace monitoring on problem-solving performance. In a laboratory experiment, we explored the monitoring environment's effects on an individual's propensity to (1) establish pattern solutions to problems, (2) recognize when pattern solutions are no longer efficient, and (3) solve complex problems. Under three work monitoring regimes-no monitoring, human monitoring, and electronic monitoring-114 participants solved puzzles for monetary rewards. Based on research related to worker autonomy and theory of social facilitation, we hypothesized that monitored (versus non-monitored) participants would (1) have more difficulty finding a pattern solution, (2) more often fail to recognize when the pattern solution is no longer efficient, and (3) solve fewer complex problems. Our results support the first two hypotheses, but in complex problem solving, an interaction was found between self-assessed ability and the monitoring environment.

  8. Optimal layout of radiological environment monitoring based on TOPSIS method

    International Nuclear Information System (INIS)

    Li Sufen; Zhou Chunlin

    2006-01-01

    TOPSIS is a method for multi-objective-decision-making, which can be applied to comprehensive assessment of environmental quality. This paper adopts it to get the optimal layout of radiological environment monitoring, it is proved that this method is a correct, simple and convenient, practical one, and beneficial to supervision departments to scientifically and reasonably layout Radiological Environment monitoring sites. (authors)

  9. Partial monitoring system Radioactivity of the Environment, 2006

    International Nuclear Information System (INIS)

    Melicherova, T.

    2007-01-01

    In this report the Partial monitoring system 'Radioactivity of the Environment' for the year 2006 is presented. International co-operation of the Slovak Hydrometeorological Institute in the Partial monitoring system 'Radioactivity of the Environment' of the Slovak Republic, international co-operation as well as financial data are reviewed

  10. Distributed intelligent urban environment monitoring system

    Science.gov (United States)

    Du, Jinsong; Wang, Wei; Gao, Jie; Cong, Rigang

    2018-02-01

    The current environmental pollution and destruction have developed into a world-wide major social problem that threatens human survival and development. Environmental monitoring is the prerequisite and basis of environmental governance, but overall, the current environmental monitoring system is facing a series of problems. Based on the electrochemical sensor, this paper designs a small, low-cost, easy to layout urban environmental quality monitoring terminal, and multi-terminal constitutes a distributed network. The system has been small-scale demonstration applications and has confirmed that the system is suitable for large-scale promotion

  11. SEL monitoring of the earth's energetic particle radiation environment

    International Nuclear Information System (INIS)

    Sauer, H.H.

    1989-01-01

    The Space Environment Laboratory (SEL) of the National Oceanic and Atmospheric Administration (NOAA) maintains instruments on board the GOES series of geostationary satellites, and aboard the NOAA/TIROS series of low-altitude, polar-orbiting satellites, which provide monitoring of the energetic particle radiation environment as well as monitoring the geostationary magnetic field and the solar x-ray flux. The data are used by the SEL Space Environment Services Center (SESC) to help provide real-time monitoring and forecasting of the state of the near earth environment and its disturbances, and to maintain a source of reliable information to research and operational activities of a variety of users

  12. Monitoring system for OpenPBS environment

    Energy Technology Data Exchange (ETDEWEB)

    Kolosov, V. [ITEP, Moscow (Russian Federation)]. E-mail: victor.kolosov@itep.ru; Lublev, Y. [ITEP, Moscow (Russian Federation); Makarychev, S. [ITEP, Moscow (Russian Federation)

    2004-11-21

    The OpenPBS batch system is widely used in the HEP community. The Open PBS package has a set of tools to check the current status of the system. This information is useful, but it is not sufficient enough for resource accounting and planning. As a solution for this problem, we developed a monitoring system which parses the logfiles from OpenPBS and stores the information into a SQL database (PostgreSQL). This allows us to analyze the data in many different ways using SQL queries. The system was used in ITEP during the last two years for batch farm monitoring.

  13. Smart Sensor Network System For Environment Monitoring

    Directory of Open Access Journals (Sweden)

    Javed Ali Baloch

    2012-07-01

    Full Text Available SSN (Smart Sensor Network systems could be used to monitor buildings with modern infrastructure, plant sites with chemical pollution, horticulture, natural habitat, wastewater management and modern transport system. To sense attributes of phenomena and make decisions on the basis of the sensed value is the primary goal of such systems. In this paper a Smart Spatially aware sensor system is presented. A smart system, which could continuously monitor the network to observe the functionality and trigger, alerts to the base station if a change in the system occurs and provide feedback periodically, on demand or even continuously depending on the nature of the application. The results of the simulation trials presented in this paper exhibit the performance of a Smart Spatially Aware Sensor Networks.

  14. MAFF monitoring of the terrestrial environment

    International Nuclear Information System (INIS)

    Sherlock, J.C.

    1993-01-01

    This paper addresses the food surveillance programme of the Ministry of Agriculture, Fisheries and Food (MAFF), in particular the Terrestrial Radioactivity Monitoring Programme (TRAMP) and the estimation of dietary intake of radionuclides. To define the surveillance programme the following issues need to be decided upon: 1) the type of food which should be analysed; 2) the nature of the contaminants which should be analysed; and 3) the geographical location from which the food samples should be taken. (author)

  15. Corrosion potential monitoring in nuclear power environments

    International Nuclear Information System (INIS)

    Molander, A.

    2004-01-01

    Full text of publication follows: corrosion monitoring. The corrosion potential is usually an important parameter or even the prime parameter for many types of corrosion processes. One typical example of the strong influence of the corrosion potential on corrosion performance is stress corrosion of sensitized stainless steel in pure high temperature water corresponding to boiling water conditions. The use of in-plant monitoring to follow the effect of hydrogen addition to mitigate stress corrosion in boiling water reactors is now a well-established technique. However, different relations between the corrosion potential of stainless steel and the oxidant concentration have been published and only recently an improved understanding of the electrochemical reactions and other conditions that determine the corrosion potential in BWR systems have been reached. This improved knowledge will be reviewed in this paper. Electrochemical measurements has also been performed in PWR systems and mainly the feedwater system on the secondary side of PWRs. The measurements performed so far have shown that electrochemical measurements are a very sensitive tool to detect and follow oxygen transients in the feedwater system. Also determinations of the minimum hydrazine dosage to the feedwater have been performed. However, PWR secondary side monitoring has not yet been utilized to the same level as BWR hydrogen water chemistry surveillance. The future potential of corrosion potential monitoring will be discussed. Electrochemical measurements are also performed in other reactor systems and in other types of reactors. Experiences will be briefly reviewed. In a BWR on hydrogen water chemistry and in the PWR secondary system the corrosion potentials show a large variation between different system parts. To postulate the material behavior at different locations the local chemical and electrochemical conditions must be known. Thus, modeling of chemical and electrochemical conditions along

  16. Process monitoring with optical fibers and harsh environment sensors

    International Nuclear Information System (INIS)

    Marcus, M.A.; Wang, A.

    1999-01-01

    This volume contains 35 papers presented at the symposium. Some of the topics covered are: sensors for the energy industry; sensors for materials evaluation and structural monitoring; sensors for engine industry; and other harsh environments sensors

  17. UARS Particle Environment Monitor (PEM) Level 3TP V001

    Data.gov (United States)

    National Aeronautics and Space Administration — The Particle Environment Monitor (PEM) Level 3TP data product consists of daily, 65.536 second and 2.048 interval time-ordered, vertical profiles of electron and...

  18. Equivalência semântica, de itens e conceitual da versão brasileira do Neighborhood Environment Walkability Scale for Youth (NEWS-Y

    Directory of Open Access Journals (Sweden)

    Alex Vieira Lima

    2013-12-01

    Full Text Available O objetivo deste estudo foi descrever o processo de tradução e adaptação transcultural da versão brasileira do questionário Neighborhood Environment Walkability Scale for Youth (NEWS-Y. Foram realizadas traduções independentes para o português da versão original do NEWS-Y e respectivas retrotraduções para o inglês. A análise da adaptação semântica e conceitual foi realizada por um grupo de especialistas. A versão traduzida do NEWS-Y foi aplicada em amostra de oito adolescentes de ambos os sexos e apresentou fácil compreensão. Após discretas modificações apontadas nos processos de tradução, o grupo de especialistas considerou que a versão para o idioma português do NEWS-Y apresentou equivalências semântica e conceitual. A versão traduzida do NEWS-Y necessitou de poucos ajustes para garantir a adaptação conceitual, de itens e semântica. Sugere-se que estudos complementares sejam realizados para analisar as outras etapas da adaptação transcultural da versão do NEWS-Y em português no contexto brasileiro.

  19. Transmission Tower Environment Monitoring Using UAV

    International Nuclear Information System (INIS)

    Redzuwan, Redia Mohd; Din, Norashidah Md; Baharuddin, Mohd Zafri; Mustafa, Intan Shafinaz; Omar, Rohayu Che'

    2013-01-01

    Power utility engineers used to conduct ground survey to collect topographic data. Therefore, they can get detailed and accurate information, but these techniques take a lot of labors and expenses, and spending times for the surveying. An attractive solution to the ground survey is using images taken using Unmanned Aerial Vehicle (UAV). Images captured from UAV can be collected quickly and efficiently over the same area covered in the land survey, in a fraction of the time. The purpose of this research is to mosaic the large numbers of spectral images together into a region wide panoramic image which allows experts to analyze the data for transmission tower monitoring purposes.

  20. Radioactive discharges and monitoring of the environment 1988

    International Nuclear Information System (INIS)

    1989-01-01

    This annual report on Radioactive Discharges and Monitoring the Environment, 1988, summarises the programmes of Sellafield, Drigg, Chapelcross, Springfields and Capenhurst for monitoring the discharges of radioactive materials to the sea and the environment. Critical groups and environmental exposure pathways are identified and collective doses to these groups estimated. The disposal of radioactive wastes at each site is discussed. Certificates of authorisation are presented. A summary of recommended doses of specific radionuclides is given. (Author)

  1. Tritium monitoring for nuclear facilities and environment in China

    International Nuclear Information System (INIS)

    Yang Huaiyuan

    1995-12-01

    Reviews of achievement and great progress of tritium monitoring techniques for nuclear facility and environment in China over the past 30 years are made which including the development experiences of several important detectors and instruments for health physics monitoring on site and some sampling and measuring methods for environmental monitoring and assessment. Information on nation wide survey activities during 1970∼1980 years on natural environmental radioactivity level in China and the related tritium data are given. (28 refs., 6 tabs.)

  2. Environment monitoring using LabVIEW

    International Nuclear Information System (INIS)

    Hawtree, J.

    1995-01-01

    A system has been developed for electronically recording and monitoring temperature, humidity, and other environmental variables at the Silicon Detector Facility located in Lab D. The data is collected by LabVIEW software, which runs in the background on an Apple Macintosh. The software is completely portable between Macintosh, MS Windows, and Sun platforms. The hardware includes a Macintosh with 8 MB of RAM; an external ADC-1 analog-to-digital converter that uses a serial port; LabVIEW software; temperature sensors; humidity sensors; and other voltage/current sensing devices. ADC values are converted to ASCII strings and entered into files which are read over Ethernet. Advantages include automatic logging, automatic recovery after power interruptions, and the availability of stand-alone applications for other locations with inexpensive software and hardware

  3. Monitoring Of Pollutants In Museum Environment

    Directory of Open Access Journals (Sweden)

    Ana-Maria Budu

    2015-10-01

    Full Text Available Art works are affected by environmental factors as light, temperature, humidity. Air pollutants are also implicated in their degradation. The pollution in museums has two sources: the air from outside, which brings usually dust and inorganic particles, and the inside sources – the materials used for casings (sealants, textiles placed on the display cases, varnishes, wood that emanate organic compounds. The dust is composed of particles with a diameter of approximately 2µm or higher, which come from soil (silica or animal and vegetal residues (skin cells, pollen. They facilitate water condensation on objects surface and biologic attack. The inorganic compounds are a result of materials combustion (SO2, NO2, NO and in presence of water they form acidic compounds which affect the museum objects. The organic compounds are usually peroxides, acids, phthalates, formaldehyde. The effects of these pollutants are: soiling, surface discolouration, embrittlement, corrosion. Therefore, conservators are interested in monitoring the pollution degree in the display cases or in the museum air and in analyzing the effects of pollutants on the exhibited objects. They use different methods for pollutants identification, like direct reading devices based on colorimetry, that can be read after few minutes and hours (they interact with the pollutants in atmosphere, or indirect reading samples that require a laboratory. The information gathered is used for the identification of pollution source and to analyze the concentration of pollutants needed to provoke damages on the surfaces of art objects. This paper is a review of pollutants that affect the art objects and of the monitoring systems used for their identification and measuring.

  4. Smart sensors for health and environment monitoring

    CERN Document Server

    2015-01-01

    This book covers two most important applications of smart sensors, namely bio-health sensing and environmental monitoring.   The approach taken is holistic and covers the complete scope of the subject matter from the principles of the sensing mechanism, through device physics, circuit and system implementation techniques, and energy issues  to wireless connectivity solutions. It is written at a level suitable mainly for post-graduate level researchers interested in practical applications. The chapters are independent but complementary to each other, and the book works within the wider perspective of essential smart sensors for the Internet of Things (IoT).   This is the second of three books based on the Integrated Smart Sensors research project, which describe the development of innovative devices, circuits, and system-level enabling technologies.  The aim of the project was to develop common platforms on which various devices and sensors can be loaded, and to create systems offering significant improve...

  5. Results of Monitoring at Olkiluoto in 2006. Environment

    International Nuclear Information System (INIS)

    Haapanen, R.

    2007-07-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2006. This is the third annual report. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground characterization facility. Although some of the nuclear power production related monitoring studies by TVO (the power company) have been going on from the 1970s, the repository-related environmental monitoring of Olkiluoto Island has only recently been comprehensive. Consequently, the first Biosphere Description Report was written in 2006. This work further produced some analyses belonging to the environmental monitoring programme, namely the estimates of biomass in terrestrial vegetation (forests) and a preliminary estimate of the biomass in terrestrial fauna (moose). In the monitoring data, the ongoing construction work (OL3, ONKALO and related infrastructure) is seen for instance in raised noise levels and deposition of base cations and iron. The land-use continues to change, but where there is natural environment, it resembles other coastal locations. The nearby marine environment is affected by the cooling water from the nuclear power plant. (orig.)

  6. Results of monitoring at Olkiluoto in 2008. Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2009-09-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2008. These summary reports have been published since 2005 (target year 2004). The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground characterization facility. Although some of the nuclear power production related monitoring studies by TVO (the power company) have been going on from the 1970s, the repository-related environmental monitoring of Olkiluoto Island has only recently been comprehensive. However, the monitoring programme evolves according to experiences from modelling work and increasing knowledge of most important site data. For example, in addition to the originally planned activities, in 2008 several studies on fauna were carried out, some soil and vegetation transects running from land to sea were established, a separate survey of water quality with automatic detectors was carried out and zooplankton and organic carbon studies were started in context of sea monitoring. In the monitoring data, the ongoing construction work (OL3, ONKALO and related infrastructure) is seen for instance in raised levels of noise and some deposited elements. The land-use continues to change, but where there is natural environment is affected by the cooling water from the nuclear power plant. (orig.)

  7. System for ecological monitoring and assessment for NPP site environment

    International Nuclear Information System (INIS)

    Vorob'ev, E.I.; Olejnikov, N.F.; Reznichenko, V.Yu.

    1987-01-01

    On the basis of the Leningrad NPP named after V.I. Lenin the development of a system for ecological monitoring and assessment (EMA) of the environment state and health of personnel and population has started in the EMA program framework. The program of ecological monitoring and assessment coordinates the works on the study of NPP effect on the nature and people, effect of separate factors and their combination, methods and models for the description of the effects, forecasting and evaluation, selection of the optimal protection strategies. Scientific foundations, structure and content of the EMA program are given to coordinate the works carried out according to the program with other works carried out in the country in this direction. The paper deals with the composition of monitoring parameters of the standard system of ecological monitoring of the environment for NPP

  8. Overview of the LHD central control room data monitoring environment

    International Nuclear Information System (INIS)

    Emoto, M.; Yoshinuma, M.; Yoshida, M.; Nakanishi, H.; Iwata, C.; Ohsuna, M.; Nonomura, M.; Imazu, S.; Yokota, M.; Aoyagi, M.; Ogawa, H.; Ida, K.; Watanabe, K.; Kaneko, O.

    2016-01-01

    Highlights: • In this paper, the data monitoring environments in the LHD central control room, for example, summary data graph and video monitoring tools are introduced. Also, the environments for the remote participants are introduced. - Abstract: During the Large Helical Device (LHD) experiments, many scientists and technical staff are working in the central control room to operate the experiment. They must manage the diagnostics and controlling devices referring to the results of the last plasma shot. Also, the experiment coordinator must decide the conditions for the subsequent experiments using the results. Furthermore, many scientists are participating in the experiment from remote sites. Therefore, it is important to share the information in the control room quickly, such as the results of the last plasma discharge, with the remote user as well as with the staff in the room. In this paper, the data monitoring environment in the LHD central control room is introduced.

  9. Overview of the LHD central control room data monitoring environment

    Energy Technology Data Exchange (ETDEWEB)

    Emoto, M., E-mail: emoto.masahiko@nifs.ac.jp; Yoshinuma, M.; Yoshida, M.; Nakanishi, H.; Iwata, C.; Ohsuna, M.; Nonomura, M.; Imazu, S.; Yokota, M.; Aoyagi, M.; Ogawa, H.; Ida, K.; Watanabe, K.; Kaneko, O.

    2016-11-15

    Highlights: • In this paper, the data monitoring environments in the LHD central control room, for example, summary data graph and video monitoring tools are introduced. Also, the environments for the remote participants are introduced. - Abstract: During the Large Helical Device (LHD) experiments, many scientists and technical staff are working in the central control room to operate the experiment. They must manage the diagnostics and controlling devices referring to the results of the last plasma shot. Also, the experiment coordinator must decide the conditions for the subsequent experiments using the results. Furthermore, many scientists are participating in the experiment from remote sites. Therefore, it is important to share the information in the control room quickly, such as the results of the last plasma discharge, with the remote user as well as with the staff in the room. In this paper, the data monitoring environment in the LHD central control room is introduced.

  10. IoT enabled aquatic drone for environment monitoring

    OpenAIRE

    Matos, João Ricardo Baptista de

    2016-01-01

    This thesis presents a platform that tackles environment monitoring by using air and water quality sensors to provide data for the user to know what is happening in that surveilled area. The hardware is incorporated in a sensing module in order to be used with an Unmanned Surface Vehicle (USV). It presents a monitoring system based on Raspberry Pi platform and a multichannel sensing module associated with water quality and air quality measurement parameters. Thus, the temper...

  11. Real time nanogravimetric monitoring of corrosion in radioactive environments

    OpenAIRE

    Tzagkaroulakis, Ioannis; Boxall, Colin

    2017-01-01

    Monitoring and understanding the mechanism of metal corrosion throughout the nuclear fuel cycle play a key role in the safe asset management of facilities. They also provide information essential for making an informed choice regarding the selection of decontamination methods for steel plant and equipment scheduled for decommissioning. Recent advances in Quartz Crystal Nanobalance (QCN) technology offer the means of monitoring corrosion in-situ, in radiologically harsh environments, in real t...

  12. Radioactivity monitoring of the Irish marine environment 1987

    International Nuclear Information System (INIS)

    O'Grady, J.; Currivan, L.

    1990-06-01

    This report represents the results of the Board's monitoring of radioactivity levels in the Irish marine environment during 1987. The principal objective of the monitoring programme is to obtain estimates of radiation doses to the Irish public arising from caesium-137 and caesium 134, the main contaminating radionuclides. Estimates are presented of the radiation doses to the Irish public arising from the consumption of fish and shellfish contaminated with radiocaesium

  13. Results of monitoring at Olkiluoto in 2007. Environment

    International Nuclear Information System (INIS)

    Haapanen, R.

    2008-06-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2007. These summary reports have been published since 2005 (target year 2004). The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground characterization facility. Although some of the nuclear power production related monitoring studies by TVO (the power company) have been going on from the 1970s, the repository-related environmental monitoring of Olkiluoto Island has only recently been comprehensive. In the monitoring data, the ongoing construction work (OL3, ONKALO and related infrastructure) is seen for instance in raised noise levels and deposition of base cations and iron. The land-use continues to change, but where there is natural environment, it resembles other coastal locations. The nearby marine environment is affected by the cooling water from the nuclear power plant. (orig.)

  14. Crack Growth Monitoring in Harsh Environments by Electric Potential Measurements

    International Nuclear Information System (INIS)

    Lloyd, Wilson Randolph; Reuter, Walter Graham; Weinberg, David Michael

    1999-01-01

    Electric potential measurement (EPM) technology offers an attractive alternative to conventional nondestructive evaluation (NDE) for monitoring crack growth in harsh environments. Where conventional NDE methods typically require localized human interaction, the EPM technique developed at the Idaho National Engineering and Environmental Laboratory (INEEL) can be operated remotely and automatically. Once a crack-like defect is discovered via conventional means, EPM can be applied to monitor local crack size changes. This is of particular interest in situations where an identified structural defect is not immediately rejectable from a fitness-for-service viewpoint, but due to operational and environmental conditions may grow to an unsafe size with continuing operation. If the location is in a harsh environment where periodic monitoring by normal means is either too costly or not possible, a very expensive repair may be immediately mandated. However, the proposed EPM methodology may offer a unique monitoring capability that would allow for continuing service. INEEL has developed this methodology, supporting equipment, and calibration information to apply EPM in a field environment for just this purpose. Laboratory and pilot scale tests on full-size engineering structures (pressure vessels and piping) have been successfully performed. The technique applicable is many severe environments because the sensitive equipment (electronics, operators) can be situated in a remote location, with only current and voltage probe electrical leads entering into the harsh environment. Experimental results showing the utility of the methodology are presented, and unique application concepts that have been examined by multiple experiments are discussed

  15. Network monitoring module of BES III system environment

    International Nuclear Information System (INIS)

    Song Liwen; Zhao Jingwei; Zhang Bingyun

    2002-01-01

    In order to meet the needs of the complicated network architecture of BES III (Beijing Spectrometer III) and make sure normal online running in the future, it is necessary to develop a multi-platforms Network Monitoring Tool which can help system administrator monitor and manage BES III network. The author provides a module that can monitor not only the traffic of switch-router's ports but also the performance status of key devices in the network environment, meanwhile it can also give warning to manager and submit the related reports. the great sense, the theory basis, the implementing method and the graph in formation of this tool will be discussed

  16. Modification of GNPS environment radiation monitoring network system

    International Nuclear Information System (INIS)

    Jiang Lili; Cao Chunsheng

    1999-01-01

    GNPS Environment Radiation Continuous Monitoring System (KRS), the only real time on-line system of site radiation monitoring, was put into service in 1993 prior to the first loading the the plant. It is revealed through several years of operation that this system has some deficiencies such as inadequate real time monitoring means, no figure and diagram display function on the central computer, high failures, frequent failure warning signals, thus making the availability of the system at a low level. In recent years, with the rapid development of computer network technology and increasingly strict requirements on the NPP environment protection raised by the government and public, KRS modification had become necessary and urgent. In 1996, GNPS carried out modification work on the measuring geometry condition of γ radiation monitoring sub-station and lightening protection. To enhance the functions of real time monitoring and data auto-processing, further modification of the system was made in 1998, including the update of the software and hardware of KRS central processor, set-up of system computer local network and database. In this way, the system availability and monitoring quality are greatly improved and effective monitoring and analysis means are provided for gaseous release during normal operation and under accident condition

  17. Monitoring radioactivity in the environment: context, objectives, challenges and prospects

    International Nuclear Information System (INIS)

    Collet, J.; Jaunet, P.

    2010-01-01

    The aims of environmental radioactivity monitoring are multiples: protection of human health and environment, knowledge of the radiological status of the environment, early detection of radiological events, public information. This monitoring is ensured by several stakeholders (licensees, IRSN, ASN, state and local authorities, associations...) and in all environment compartments (air, water, soil, fauna and flora...). Within a European regulatory context, the Nuclear Transparency and Security Act 2006-686 of 13 June 2006 (TSN Act) reinforces the importance attached to consideration of safety, radiation protection and the environment. Other developments in the scope of environmental radioactivity must be noted: new stakeholders, lower background radiation, deployment of the French National Network of Environmental Radioactivity Monitoring (RNM), evolution of the ICPR thoughts to take better account of environmental protection, post-accident management doctrine, new concerns about environmental behaviour of some radionuclides. In order to maintain a quality policy in the field of environmental radioactivity measurements and to ensure the transparency of information, ASN will make sure that the strategy of environmental radioactivity monitoring will take into account these concerns. (author)

  18. SLIM (SEM for Low Interception Monitoring) An Innovative Non-Destructive Beam Monitor for the Extraction Lines of a Hadrontherapy Centre

    CERN Document Server

    Badano, L; Pezzetta, M; Molinari, G

    2003-01-01

    Real time monitoring of hadrontherapy beam intensity and profile is a critical issue for the optimisation of the dose delivery to the patient carcinogenic tissue, the patient safety and the operation of the accelerator complex. For this purpose an innovative beam monitor, based on the secondary emission of electrons by a nonperturbative, sub-micron thick Al target placed directly in the extracted beam path, is being proposed. The secondary electrons, accelerated by an electrostatics focusing system, are detected by a monolithic silicon position sensitive sensor, which provides the beam intensity and its position with a precision of 1 mm at 10 kHz frame rate. The conceptual design and the engineering study optimised for hadrontherapy, together with the results of the preliminary tests of the first system prototype, will be presented.

  19. Radiation monitoring in the NPP environment, control of radioactivity in NPP-environment system

    International Nuclear Information System (INIS)

    Egorov, Yu.A.

    1987-01-01

    Problems of radiation monitoring and control of the NPP-environment system (NPPES) are considered. Radiation control system at the NPP and in the environment provides for the control of the NPP, considered as the source of radioactive releases in the environment and for the environmental radiation climate control. It is shown, that the radiation control of the NPP-environment system must be based on the ecological normalization principles of the NPP environmental impacts. Ecological normalization should be individual for the NPP region of each ecosystem. The necessity to organize and conduct radiation ecological monitoring in the NPP regions is pointed out. Radiation ecological monitoring will provide for both environmental current radiation control and information for mathematical models, used in the NPPES radiation control

  20. Results of monitoring at Olkiluoto in 2012. Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2014-04-01

    In 2003, Posiva Oy presented a programme for monitoring at Olkiluoto during construction and operation of ONKALO. In 2012 the monitoring programme was updated to concern the years 2012-2018. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). This Working Report presents the main results of Posiva's environmental monitoring programme on Olkiluoto Island in 2012. Results are presented under five topics: 1. Evolution of geosphere, 2. Biosphere modelling input data, 3. Interaction between surface environment and groundwater in bedrock, 4. Environmental impact and 5. Baseline of monitoring of radioactive releases. Concerning the evolution of geosphere, LIDAR-scannings were done in the Olkiluoto area in 2012. The acquired data can be used for elevation and other modelling purposes. The soil solution quality in 2012 was quite comparable to that in earlier years. Proximity of the sea and the young age of soils are seen in soil solution results. Biosphere modelling input data in 2012 included e.g. continuous tree litterfall and transpiration data, as well as updated game statistics and population estimates of fauna, a fishery survey from the River Eurajoki (2011) and basic monitoring data from Olkiluoto offshore properties. Interaction between surface environment and groundwater in bedrock includes e.g. weather and surface water monitoring data. Environmental impact analyses included e.g. monitoring of noise, air quality, effluent waters and private drilled wells. Noise monitoring in the vicinity of ONKALO showed that in the case of raised noise levels the sources are mainly the traffic on Olkiluodontie road, the air conditioning of ONKALO and occasional sources such as springtime bird sounds. Construction activities in the area were seen in increased amount of NO 3 -N in the bulk deposition, and Al and Fe accumulating on needle surfaces in areas close to the rock piling and crushing area. Scots

  1. Results of monitoring at Olkiluoto in 2012. Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. (ed.) [Haapanen Forest Consulting, Vanhakylae (Finland)

    2014-04-15

    In 2003, Posiva Oy presented a programme for monitoring at Olkiluoto during construction and operation of ONKALO. In 2012 the monitoring programme was updated to concern the years 2012-2018. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). This Working Report presents the main results of Posiva's environmental monitoring programme on Olkiluoto Island in 2012. Results are presented under five topics: 1. Evolution of geosphere, 2. Biosphere modelling input data, 3. Interaction between surface environment and groundwater in bedrock, 4. Environmental impact and 5. Baseline of monitoring of radioactive releases. Concerning the evolution of geosphere, LIDAR-scannings were done in the Olkiluoto area in 2012. The acquired data can be used for elevation and other modelling purposes. The soil solution quality in 2012 was quite comparable to that in earlier years. Proximity of the sea and the young age of soils are seen in soil solution results. Biosphere modelling input data in 2012 included e.g. continuous tree litterfall and transpiration data, as well as updated game statistics and population estimates of fauna, a fishery survey from the River Eurajoki (2011) and basic monitoring data from Olkiluoto offshore properties. Interaction between surface environment and groundwater in bedrock includes e.g. weather and surface water monitoring data. Environmental impact analyses included e.g. monitoring of noise, air quality, effluent waters and private drilled wells. Noise monitoring in the vicinity of ONKALO showed that in the case of raised noise levels the sources are mainly the traffic on Olkiluodontie road, the air conditioning of ONKALO and occasional sources such as springtime bird sounds. Construction activities in the area were seen in increased amount of NO{sub 3}-N in the bulk deposition, and Al and Fe accumulating on needle surfaces in areas close to the rock piling and crushing area

  2. Results of monitoring at Olkiluoto in 2009. Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2010-10-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2009. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to the experiences gained from the modelling work and an increased understanding of the site. Augmentations in 2009 include e.g. establishment of a new forest intensive monitoring plot (FIP14), continuation of studies on fine roots and on the species composition and abundances of small mammals. Line transect samplings of ants, terrestrial snails and earthworms were carried out and a systematic monitoring of island birds was started. In addition, a project was started where the sediment load and factors affecting the sediment transportation into Eurajoensalmi bay is examined. Dust produced during construction of the third nuclear power unit (OL3), ONKALO and related infrastructure can be seen in the soil solution and deposition results. Furthermore, the construction works and road traffic have a raising effect on the noise levels of the immediate surroundings. The land-use continues to change, but the remaining natural environment resembles other coastal locations. The young age of the soils and the closeness of the sea are reflected in the soil properties. Mammalian fauna on the island is typical of coastal

  3. Results of monitoring at Olkiluoto in 2009. Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. (ed.) (Haapanen Forest Consulting, Vanhakylae (Finland))

    2010-10-15

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2009. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to the experiences gained from the modelling work and an increased understanding of the site. Augmentations in 2009 include e.g. establishment of a new forest intensive monitoring plot (FIP14), continuation of studies on fine roots and on the species composition and abundances of small mammals. Line transect samplings of ants, terrestrial snails and earthworms were carried out and a systematic monitoring of island birds was started. In addition, a project was started where the sediment load and factors affecting the sediment transportation into Eurajoensalmi bay is examined. Dust produced during construction of the third nuclear power unit (OL3), ONKALO and related infrastructure can be seen in the soil solution and deposition results. Furthermore, the construction works and road traffic have a raising effect on the noise levels of the immediate surroundings. The land-use continues to change, but the remaining natural environment resembles other coastal locations. The young age of the soils and the closeness of the sea are reflected in the soil properties. Mammalian fauna on the island is typical of coastal

  4. Radioactivity monitoring of the Irish marine environment 1991 and 1992

    International Nuclear Information System (INIS)

    McGarry, A.; Lyons, S.; McEnri, C.; Ryan, T.; O'Colmain, M.; Cunningham, J.D.

    1994-05-01

    This report presents the results of the Radiological Protection Institute's programme of monitoring of radioactivity in the seas around Ireland during 1991 and 1992. The principal objective of the monitoring programme is to review the risks to human health arising from the Sellafield discharges. Secondary objectives include studies of the distribution of the significant contaminating radionuclides in the marie environment and the identification of trends with a view to assessing possible future effects. Estimates of the radiation doses to the Irish public are also presented in this report. 23 refs. 24 tabs. 9 figs

  5. Web based remote monitoring and controlling system for vulnerable environments

    Science.gov (United States)

    Thomas, Aparna; George, Minu

    2016-03-01

    The two major areas of concern in industrial establishments are monitoring and security. The remote monitoring and controlling can be established with the help of Web technology. Managers can monitor and control the equipment in the remote area through a web browser. The targeted area includes all type of susceptible environment like gas filling station, research and development laboratories. The environmental parameters like temperature, light intensity, gas etc. can be monitored. Security is a very important factor in an industrial setup. So motion detection feature is added to the system to ensure the security. The remote monitoring and controlling system makes use of the latest, less power consumptive and fast working microcontroller like S3C2440. This system is based on ARM9 and Linux operating system. The ARM9 will collect the sensor data and establish real time video monitoring along with motion detection feature. These captured video data as well as environmental data is transmitted over internet using embedded web server which is integrated within the ARM9 board.

  6. Design of the Resources and Environment Monitoring Website in Kashgar

    International Nuclear Information System (INIS)

    Huang, Z; Lin, Q Z; Wang, Q J

    2014-01-01

    Despite the development of the web geographical information system (web GIS), many useful spatial analysis functions are ignored in the system implementation. As Kashgar is rich in natural resources, it is of great significance to monitor the ample natural resource and environment situation in the region. Therefore, with multiple uses of spatial analysis, resources and environment monitoring website of Kashgar was built. Functions of water, vegetation, ice and snow extraction, task management, change assessment as well as thematic mapping and reports based on TM remote sensing images were implemented in the website. The design of the website was presented based on database management tier, the business logic tier and the top-level presentation tier. The vital operations of the website were introduced and the general performance was evaluated

  7. Radiation protection instrumentation. Monitoring equipment. Radioactive aerosols in the environment

    International Nuclear Information System (INIS)

    1996-01-01

    This international standard applies to portable or installed equipment for continuous monitoring of radioactive aerosols in the environment in normal and emergency conditions. Monitoring involves continuous sampling and, where desirable, automatic start of sampling. The document applies particularly to the following assignments: (i) determination of the volume activity of radionuclides in the form of aerosols, either per time unit, along with its time changes, or in the integral form over a longer time period such as 24 h, and measurement of the volume sampled; (ii) triggering a warning alarm signal if the preset volume activity or time integral of the volume activity of aerosols has been exceeded. The document deals with radioactive aerosol monitor design, testing procedures, and documentation. Appended tables refer to the reference and normal testing conditions, tests in normal testing conditions, tests during changes of the affecting quantities, and tests of the air circuit. (P.A.)

  8. Metagenomic frameworks for monitoring antibiotic resistance in aquatic environments.

    Science.gov (United States)

    Port, Jesse A; Cullen, Alison C; Wallace, James C; Smith, Marissa N; Faustman, Elaine M

    2014-03-01

    High-throughput genomic technologies offer new approaches for environmental health monitoring, including metagenomic surveillance of antibiotic resistance determinants (ARDs). Although natural environments serve as reservoirs for antibiotic resistance genes that can be transferred to pathogenic and human commensal bacteria, monitoring of these determinants has been infrequent and incomplete. Furthermore, surveillance efforts have not been integrated into public health decision making. We used a metagenomic epidemiology-based approach to develop an ARD index that quantifies antibiotic resistance potential, and we analyzed this index for common modal patterns across environmental samples. We also explored how metagenomic data such as this index could be conceptually framed within an early risk management context. We analyzed 25 published data sets from shotgun pyrosequencing projects. The samples consisted of microbial community DNA collected from marine and freshwater environments across a gradient of human impact. We used principal component analysis to identify index patterns across samples. We observed significant differences in the overall index and index subcategory levels when comparing ecosystems more proximal versus distal to human impact. The selection of different sequence similarity thresholds strongly influenced the index measurements. Unique index subcategory modes distinguished the different metagenomes. Broad-scale screening of ARD potential using this index revealed utility for framing environmental health monitoring and surveillance. This approach holds promise as a screening tool for establishing baseline ARD levels that can be used to inform and prioritize decision making regarding management of ARD sources and human exposure routes. Port JA, Cullen AC, Wallace JC, Smith MN, Faustman EM. 2014. Metagenomic frameworks for monitoring antibiotic resistance in aquatic environments. Environ Health Perspect 122:222–228; http://dx.doi.org/10.1289/ehp

  9. Results of monitoring at Olkiluoto in 2010 - Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2011-10-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2010. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Augmentations in 2010 include one previously unmonitored private drilled well, and sampling of crop plants, aquatic macrophytes, and bottom fauna, as well as soil and water in order to obtain more data on site-specific concentration ratios. In addition to Olkiluoto Island, two so called reference lakes have been included in the sampling. Studies have been going on on one reference mire, as well. Bottom fauna studies of River Eurajoki exist from late 1970s, but have not been presented here before. Dust produced during construction of the third nuclear power unit (OL3), ONKALO and related infrastructure can be seen in the analysis results of needle litter. The construction works and road traffic have a raising effect on the noise levels of the immediate surroundings. The land-use continues to change, but the remaining natural environment resembles other coastal locations. The young age of the soils and the closeness of the sea are reflected in the soil properties. Mammalian fauna on the island is typical of coastal areas in

  10. Results of monitoring at Olkiluoto in 2010 - Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. (ed.) [Haapanen Forest Consulting, Vanhakylae (Finland)

    2011-10-15

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2010. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Augmentations in 2010 include one previously unmonitored private drilled well, and sampling of crop plants, aquatic macrophytes, and bottom fauna, as well as soil and water in order to obtain more data on site-specific concentration ratios. In addition to Olkiluoto Island, two so called reference lakes have been included in the sampling. Studies have been going on on one reference mire, as well. Bottom fauna studies of River Eurajoki exist from late 1970s, but have not been presented here before. Dust produced during construction of the third nuclear power unit (OL3), ONKALO and related infrastructure can be seen in the analysis results of needle litter. The construction works and road traffic have a raising effect on the noise levels of the immediate surroundings. The land-use continues to change, but the remaining natural environment resembles other coastal locations. The young age of the soils and the closeness of the sea are reflected in the soil properties. Mammalian fauna on the island is typical of coastal

  11. Results of monitoring at Olkiluoto in 2005. Environment

    International Nuclear Information System (INIS)

    Haapanen, R.

    2006-08-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2005. This is the second annual report. Monitoring has been carried out for varying time periods depending on the sector: some monitoring activities performed by TVO originate from the 1970s, others connected with the construction of the final disposal repository for nuclear waste and the underground research facility ONKALO have just started. The system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for environmental impact analyses. In 2005 the deposition collectors and nearby needles caught some dust from the rock piling and crushing activities and traffic. Noise was another clear effect, originating mostly from OL3 construction, rock piling and crushing area and the concrete station. The studies further confirmed that the vegetation, forests, soils and animal life are typical of a coastal region within the same vegetation zone. The nearby marine environment is affected by the cooling water from the nuclear power plant, to varying extents depending on the organism and the distance. Monitoring of marine environments as well as radionuclide analyses at the moment produce reference data for the future and create a basis for the construction of a model, as no input from Posiva's activities will influence these areas for a long time. (orig.)

  12. Results of Monitoring at Olkiluoto in 2004. Environment

    International Nuclear Information System (INIS)

    Haapanen, R.

    2005-07-01

    This report presents the main results of the environmental monitoring programme connected with Posiva Oy's activities on Olkiluoto island. This is the first annual report and covers the years 2004 and partly 2003. Monitoring has been carried out for varying time periods depending on the sector: some monitoring activities performed by TVO originate from the 1970s, others connected with the construction of the final disposal repository for nuclear waste and the underground research facility ONKALO are about to start. The system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for environmental impact analyses. No unexplainable deviations from reference data were seen in the results presented in this report. The vegetation, forests, soils and animal life are typical of a coastal region within the same vegetation zone. The nearby marine environment is affected by the cooling water from the nuclear power plant, to varying extents depending on the organism and the distance. Monitoring of marine environments as well as radionuclide analyses at the moment produce reference data for the future and create a basis for the construction of a model, as no input from Posiva's activities will influence these areas for a long time. (orig.)

  13. An 'artificial mussel' for monitoring heavy metals in marine environments

    International Nuclear Information System (INIS)

    Wu, Rudolf S.S.; Lau, T.C.; Fung, Wendy K.M.; Ko, P.H.; Leung, Kenneth M.Y.

    2007-01-01

    A new chemical sampling device, artificial mussel (AM), has been developed for monitoring metals in marine environments. This device consists of a polymer ligand suspended in artificial seawater within a Perspex tubing, and enclosed with semi-permeable gel at both ends. Laboratory and field experiments were carried out to examine the uptake of five metals (Cd, Cr, Cu, Pb and Zn) by the AM. Uptake of metals by AM was proportional to the exposure metal concentrations, and the AM was able to accumulate the ASV labile fractions of metals. Uptake and release of the metals of AM are similar to those of the mussel Perna viridis, but less affected by salinity and temperature. Field studies demonstrated that the AM can not only provide a time-integrated estimate of metals concentrations, but also allows comparisons of metal levels in different environments and geographical areas beyond the natural distribution limits of biomonitors. - A new monitoring device to provide a time-integrated estimate for monitoring metals in marine environments

  14. Monitoring the impacts of trade agreements on food environments.

    Science.gov (United States)

    Friel, S; Hattersley, L; Snowdon, W; Thow, A-M; Lobstein, T; Sanders, D; Barquera, S; Mohan, S; Hawkes, C; Kelly, B; Kumanyika, S; L'Abbe, M; Lee, A; Ma, J; Macmullan, J; Monteiro, C; Neal, B; Rayner, M; Sacks, G; Swinburn, B; Vandevijvere, S; Walker, C

    2013-10-01

    The liberalization of international trade and foreign direct investment through multilateral, regional and bilateral agreements has had profound implications for the structure and nature of food systems, and therefore, for the availability, nutritional quality, accessibility, price and promotion of foods in different locations. Public health attention has only relatively recently turned to the links between trade and investment agreements, diets and health, and there is currently no systematic monitoring of this area. This paper reviews the available evidence on the links between trade agreements, food environments and diets from an obesity and non-communicable disease (NCD) perspective. Based on the key issues identified through the review, the paper outlines an approach for monitoring the potential impact of trade agreements on food environments and obesity/NCD risks. The proposed monitoring approach encompasses a set of guiding principles, recommended procedures for data collection and analysis, and quantifiable 'minimal', 'expanded' and 'optimal' measurement indicators to be tailored to national priorities, capacity and resources. Formal risk assessment processes of existing and evolving trade and investment agreements, which focus on their impacts on food environments will help inform the development of healthy trade policy, strengthen domestic nutrition and health policy space and ultimately protect population nutrition. © 2013 The Authors. Obesity Reviews published by John Wiley & Sons Ltd on behalf of the International Association for the Study of Obesity.

  15. Radioactivity Monitoring of the Irish Environment 2010-2011

    International Nuclear Information System (INIS)

    McGinnity, P.; Currivan, L.; Dowdall, A.; Hanley, O.; Kelleher, K.; McKittrick, L.; Pollard, D.; Somerville, S.; Wong, J.; McMahon, C.

    2012-11-01

    This report presents the results of the environmental radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland RPII during 2010 and 2011. The RPII has routinely monitored levels of radioactivity in the Irish environment since 1982 and this is the latest in the RPII's series of environmental monitoring reports. The RPII reviews and updates its environmental programme annually to ensure it remains relevant and continues to focus on the most important sources of radioactivity in the environment. The data presented in this report confirm that while the levels of artificial radioactivity in the Irish environment are detectable, they are low. They do not pose a significant risk to the human health of the Irish population. Trace amounts of radioactive isotopes consistent with the Fukushima nuclear accident were detected in air, rainwater and milk samples during the period March to May 2011. These increases in levels of radioactivity were not of concern from a public health point of view. For the remainder of the reporting period, activity concentrations of radionuclides in airborne particles were low and consistent with measurements made in recent years. Radioactivity levels in milk, mixed diet and a wide range of foodstuffs were low and, for the majority of samples, below the detection limits. All drinking waters tested were found to be in compliance with the total indicative dose defined in national and EU legislation. The doses incurred by the Irish public in 2010 and 2011 as a result of artificial radioactivity in the marine environment are small when compared to dose limits or to natural radiation doses received by the Irish public. The doses to the most exposed individuals, members of the oyster and mussel farmers critical group, were approximately 0.02 per cent and 0.05 per cent of the annual dose limit of 1000 microsieverts for members of the public from practices involving controllable sources of radiation in 2010 and

  16. SPACE RADIATION ENVIRONMENT MONITORED BY KITSAT-1 AND KITSAT-2

    Directory of Open Access Journals (Sweden)

    Y. H. Shin

    1996-06-01

    Full Text Available The results of space radiation experiments carried out on board the first two Korean technology demonstration microsatellites are presented in this paper. The first satellite, KITSAT-1, launched in August 1992, carries a radiation monitoring payload called cosmic ray experiment(CRE for characterizing the low-earth orbit(LEO radiation environment. The CRE consists of two sub-systems: the cosmic particle experiment (CPE and the total dose experiment(TDE. In addition, single event upset(SEUrates of the program memory and the RAM disk are also monitored. The second satellite, KITSAT-2, launched in September 1993, carries a newly developed 32-bit on-board computer(OBC, KASCOM(KAIST satellite computer in addition to OBC186. SEUs ocurred in the KASCOM, as well as in the program memory and RAM disk memory, have been monitored since the beginning of the satellite operation. These two satellites, which are very similar in structures but different in orbits, provide a unique opportunity to study the effects of the radiation environment characterized by the orbit.

  17. Radioactivity Monitoring of the Irish Environment 2003-2005

    International Nuclear Information System (INIS)

    Ryan, R.W.; Dowdall, A; Fegan, M.F.; Hayden, E.; Kelleher, K.; Long, S.; McEvoy, I.; McKittrick, L.; McMahon, C.A.; Murray, M.; Smith, K.; Sequeira, S.; Wong, J.; Pollard, D.

    2007-05-01

    This report presents the results of the environmental radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland (RPII) between 2003 and 2005. This programme aims to assess the exposure of the Irish population to anthropogenic radioactivity in the environment, to review the temporal and geographical distribution of contaminating radionuclides and to maintain systems and procedures which would allow a rapid assessment of environmental contamination to be made in the event of a radiological emergency. Radioactivity is present in the environment due to natural processes, the testing of nuclear weapons in the atmosphere, past nuclear accidents such as that at Chernobyl and the routine licensed discharge of radionuclides from nuclear installations. Liquid discharges from the British Nuclear Group reprocessing plant at Sellafield in Cumbria in the North-West of England continue to be the dominant source of anthropogenic radioactivity in the Irish marine environment. The key elements of the monitoring programme implemented by the RPII during the reporting period include; assessment of ambient radioactivity based on measurements of radioactivity in air and external gamma dose rate at permanent monitoring stations located throughout the country; assessment of levels of radioactivity in drinking water; assessment of levels of radioactivity in foodstuffs based on measurements of total diet, milk and miscellaneous ingredients; assessment of levels of radioactivity in the marine environment based on sampling and measurements of seawater, sediment, seaweed, fish and shellfish. The RPII monitored airborne radioactivity at eleven stations located throughout the country. One station is equipped with a high volume sampler, which allows global fallout concentrations to be measured, and one is equipped to detect the presence of the gas krypton-85. Krypton-85 is released into the environment primarily as a result of the reprocessing of nuclear

  18. Results of Monitoring at Olkiluoto in 2011. Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. [Haapanen Forest Consulting, Vanhakylae (Finland)

    2012-11-15

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2011. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Monitoring activities in 2011 proceeded according to the plans. The land-use of the island continues to change due to the construction work of OL3, ONKALO and related infrastructure, but the remaining natural environment resembles other coastal locations. The amount of nitrogen in the bulk deposition increased in 2011, whereas that of sulphur decreased. Some litterfall fractions showed higher Al and Fe values than earlier, likely caused by soil dust. Proximity of the sea is seen in wet deposition and soil solution results. Soil solution also reflects the young age of soils. Undestorey vegetation has shown no essential changes during the monitoring period. Mammalian fauna on the island is typical of coastal areas in Southwestern Finland. Game catches vary according to hunting pressure and natural variation in populations. The condition of the nearby sea is affected by the continuous land uplift, the shallowness of the area, the weather conditions, the general condition of the Bothnian Sea, the nutrient and sediment loads

  19. Results of Monitoring at Olkiluoto in 2011. Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2012-11-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2011. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Monitoring activities in 2011 proceeded according to the plans. The land-use of the island continues to change due to the construction work of OL3, ONKALO and related infrastructure, but the remaining natural environment resembles other coastal locations. The amount of nitrogen in the bulk deposition increased in 2011, whereas that of sulphur decreased. Some litterfall fractions showed higher Al and Fe values than earlier, likely caused by soil dust. Proximity of the sea is seen in wet deposition and soil solution results. Soil solution also reflects the young age of soils. Undestorey vegetation has shown no essential changes during the monitoring period. Mammalian fauna on the island is typical of coastal areas in Southwestern Finland. Game catches vary according to hunting pressure and natural variation in populations. The condition of the nearby sea is affected by the continuous land uplift, the shallowness of the area, the weather conditions, the general condition of the Bothnian Sea, the nutrient and sediment loads

  20. Results of Monitoring at Olkiluoto in 2011. Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. (ed.) [Haapanen Forest Consulting, Vanhakylae (Finland)

    2012-11-15

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2011. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Monitoring activities in 2011 proceeded according to the plans. The land-use of the island continues to change due to the construction work of OL3, ONKALO and related infrastructure, but the remaining natural environment resembles other coastal locations. The amount of nitrogen in the bulk deposition increased in 2011, whereas that of sulphur decreased. Some litterfall fractions showed higher Al and Fe values than earlier, likely caused by soil dust. Proximity of the sea is seen in wet deposition and soil solution results. Soil solution also reflects the young age of soils. Undestorey vegetation has shown no essential changes during the monitoring period. Mammalian fauna on the island is typical of coastal areas in Southwestern Finland. Game catches vary according to hunting pressure and natural variation in populations. The condition of the nearby sea is affected by the continuous land uplift, the shallowness of the area, the weather conditions, the general condition of the Bothnian Sea, the nutrient and sediment

  1. The Node Monitoring Component of a Scalable Systems Software Environment

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Samuel James [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    This research describes Fountain, a suite of programs used to monitor the resources of a cluster. A cluster is a collection of individual computers that are connected via a high speed communication network. They are traditionally used by users who desire more resources, such as processing power and memory, than any single computer can provide. A common drawback to effectively utilizing such a large-scale system is the management infrastructure, which often does not often scale well as the system grows. Large-scale parallel systems provide new research challenges in the area of systems software, the programs or tools that manage the system from boot-up to running a parallel job. The approach presented in this thesis utilizes a collection of separate components that communicate with each other to achieve a common goal. While systems software comprises a broad array of components, this thesis focuses on the design choices for a node monitoring component. We will describe Fountain, an implementation of the Scalable Systems Software (SSS) node monitor specification. It is targeted at aggregate node monitoring for clusters, focusing on both scalability and fault tolerance as its design goals. It leverages widely used technologies such as XML and HTTP to present an interface to other components in the SSS environment.

  2. Cable condition monitoring in a pressurized water reactor environment

    International Nuclear Information System (INIS)

    Al-Hussaini, T.J.

    1988-01-01

    Oconee Nuclear Station is the first nuclear plant designed, engineered and constructed by Duke Power Company. Even though the accelerated aging method was available to determine the life expectancy of the cable used in the reactor building, no natural aging data was available at that time. In order to be able to verify the condition of the reactor building cable over the life of the plant, an on-going cable monitoring plan was instituted. Various types of cable were selected to be monitored, and they were installed in cable life evaluation circuits in the reactor building. At five year intervals over the life of the plant, cable samples would be removed from these cable life evaluation circuits and tested to determine the effects of the reactor building environment on the integrity of the cable. A review of the cable life evaluation circuits and the results of the evaluation program to date is presented

  3. Construct mine environment monitoring system based on wireless mesh network

    Science.gov (United States)

    Chen, Xin; Ge, Gengyu; Liu, Yinmei; Cheng, Aimin; Wu, Jun; Fu, Jun

    2018-04-01

    The system uses wireless Mesh network as a network transmission medium, and strive to establish an effective and reliable underground environment monitoring system. The system combines wireless network technology and embedded technology to monitor the internal data collected in the mine and send it to the processing center for analysis and environmental assessment. The system can be divided into two parts: the main control network module and the data acquisition terminal, and the SPI bus technology is used for mutual communication between them. Multi-channel acquisition and control interface design Data acquisition and control terminal in the analog signal acquisition module, digital signal acquisition module, and digital signal output module. The main control network module running Linux operating system, in which the transplant SPI driver, USB card driver and AODV routing protocol. As a result, the internal data collection and reporting of the mine are realized.

  4. Performance of an alpha air monitor in a dusty environment

    International Nuclear Information System (INIS)

    Hoover, M.D.; Newton, G.J.; Yeh, H.C.; Seiler, F.A.; Boecker, B.B.

    1988-01-01

    The Eberline Alpha-6 Continuous Air Monitor (CAM) was evaluated for use in detecting alpha radiation from 238 Pu and 239 Pu in the presence of background aerosols of salt dust and radon progeny. The Alpha-6 method uses an embedded, multichannel analyzer and real-time computer to correct for the presence of alpha-emitting radon progeny and to accurately report plutonium air concentration in dust-free environments. However, accumulation of mg/cm 2 salt dust on the sample collection filter was found to be equivalent to an infinitely thick layer. Dust loading raises the limit of detection in proportion to the concentration of airborne salt. Proper detection of 239 Pu is impaired by airborne concentrations of salt greater than 2 mg/m 3 . Alpha spectral analysis at a central monitoring computer is recommended to avoid detection errors at higher salt concentrations. (author)

  5. Complex monitoring of aerospace and mountain environment at Beo Mussala

    International Nuclear Information System (INIS)

    Angelov, I.; Angelov, C.; Barnekov, L. and others

    2006-01-01

    The mission of BEO Moussala is the observing, complex monitoring and studies of global change processes, aerospace and mountain environment, natural hazards and technological risks. BEO Moussala is the focal point of the BEO Centre of Excellence established and promoted in the framework of FP5 project HIMONTONET essentially improving its research capacities in frame of the FP6 project BEOBAL. The basic fields of current and future activities and studies at BEO Moussala are: global change, aerospace and mountain environment, natural hazards and technological risks and not at least development, design and enhancement of measurement devices and systems. The basic parameters and characteristics of the new measuring facilities are given and discussed from the point of view of the requirements of Global Atmospheric Watch (GAW) and Global Change Programs

  6. Ao leitor sem medo

    Directory of Open Access Journals (Sweden)

    José Eisenberg

    2000-05-01

    Full Text Available O texto resenha Ao leitor sem medo, de Renato Janine Ribeiro (Belo Horizonte, UFMG, 1999.This text is a review of Ao leitor sem medo by Renato Janine Ribeiro (Belo Horizonte, UFMG, 1999

  7. An Integrated Environment Monitoring System for Underground Coal Mines—Wireless Sensor Network Subsystem with Multi-Parameter Monitoring

    OpenAIRE

    Zhang, Yu; Yang, Wei; Han, Dongsheng; Kim, Young-Il

    2014-01-01

    Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs). We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS) as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between t...

  8. Data Quality Monitoring : Automatic MOnitoRing Environment (AMORE ) Web Administration Tool in ALICE Experiment

    CERN Document Server

    Nagi, Imre

    2013-01-01

    ALICE (A Large Ion Collider Experiment) is the heavy-ion detector designed to study the physics of strongly interacting matter and the quark-gluon plasma at the CERN Large Hadron Collider (LHC). The quality of the acquired data evolves over time depending on the status of the detectors, its components and the operating environment. To get an excellent performance of detector, all detector configurations have to be set perfectly so that the data-taking can be done in an optimal way. This report describes a new implementation of the administration tools of the ALICE’s DQM framework called AMORE (Automatic MonitoRing Environment) with web technologies.

  9. Monitoring of contamination of atmospheric environment by radiation

    International Nuclear Information System (INIS)

    Ise, Hiroaki

    1995-01-01

    Atmospheric pollution has become a worldwide problem regardless of developed industrial nations and developing countries. In particular, the pollution due to automobile exhaust gas, the carcinogenic particles in diesel exhaust and their relation to various respiratory diseases are the problems. Nitrogen oxides and sulfur oxides in exhaust gas become the cause of acid rain. Radiation began to be utilized for the measurement of the concentration of floating particles and the amount of fallout dust, the forecast of the generation and diffusion of pollutants, the elucidation of the contribution of generation sources in wide areas and so on. In this report, the circumstances that radiation became to be utilized for monitoring atmospheric environment and the present status and the perspective of the radiation utilization in the field of the preservation of atmospheric environment are described. The progress of the method of measuring floating particles in Japan is explained. The automatic measurement of floating particles by β-ray absorption method and the application of β-ray absorption method to the measurement of the amount of fallout dust, generation source particles and the exposure to floating particles of individuals for health control are described. The utilization of radiation for real time monitoring, the investigation of the generation of blown-up dust, atmospheric diffusion experiment and the elucidation of the contribution of generation sources by PIXE radioactivation analysis are reported. (K.I.)

  10. Energy harvesting schemes for building interior environment monitoring

    Science.gov (United States)

    Zylka, Pawel; Pociecha, Dominik

    2016-11-01

    A vision to supply microelectronic devices without batteries making them perpetual or extending time of service in battery-oriented mobile supply schemes is the driving force of the research related to ambient energy harvesting. Energy harnessing aims thus at extracting energy from various ambient energy "pools", which generally are cost- or powerineffective to be scaled up for full-size, power-plant energy generation schemes supplying energy in electric form. These include - but are not limited to - waste heat, electromagnetic hum, vibrations, or human-generated power in addition to traditional renewable energy resources like water flow, tidal and wind energy or sun radiation which can also be exploited at the miniature scale by energy scavengers. However, in case of taking advantage of energy harvesting strategies to power up sensors monitoring environment inside buildings adaptable energy sources are restrained to only some which additionally are limited in spatial and temporal accessibility as well as available power. The paper explores experimentally an energy harvesting scheme exploiting human kinesis applicable in indoor environment for supplying a wireless indoor micro-system, monitoring ambient air properties (pressure, humidity and temperature).

  11. Survey of environment related monitoring programmes of international organizations and their contribution to international monitoring programmes

    International Nuclear Information System (INIS)

    1986-12-01

    The report is a summary of environment-related monitoring programmes of international governmental organizations and their contribution to international monitoring programmes. it presents the situation as of November 1986: This survey has been prepared by a consultant for the Secretariat as a background document for the second meeting of the Environment Experts, Economic Summit in Munich, November 1986. It serves information purposes only. No claim for completeness is intended. This report may also prove to be helpful for administrators and the scientific community as regards gaining knowledge on present arrangements, approaches and environmental activities in the framework of international organizations. In this light, the present report could facilitate communication and progress in solving pressing environmental problems on the international level. (orig.)

  12. Information system of partial monitoring system 'Radioactivity of the environment'

    International Nuclear Information System (INIS)

    Melicherova, T.

    2007-01-01

    Slovak Hydrometeorological Institute (SHMI) is operator of radiation monitoring from 1963. At present SHMI operates in its monitoring network 23 detectors GammaTracer fy Genitron, one mobile detector and one standby detector. Radiation data (dose rate in the unit nSv/h) from detectors in the automated meteorological stations are transmitted by data-logger and private institute network to National Telecommunication Centre in Bratislava. The data from MSS (message switch system) are inserted into the database. The 1 hours and 24 hours averages are computed on the server automatically. Delay between time of measurements and time of inserting data to database is only 10 min. Radiation files from SHMI network are on-line transmitted to information system of Nuclear Regulatory Authority of the Slovak Republic and to information system of Slovak Army. Transmission to to Crisis Centre of Civil Protection is under reconstruction at present. Database contains one table for radiation data and several tables for configurations, catalogues of stations and additional tables. Database works in environment client-server. On client PC runs the user front-end application. This application provides to display the data using many filters, to display tables with configurations concerning technical equipment, to display maps, graphs, etc. There is the possibility to store data into the archives, to make reports and to analyse data in the environment of professional statistical software. Precipitations values from meteorological stations were integrated do the information system of radiation monitoring for better interpretation of gamma dose rate values. SHMI cooperates in the radiation data exchange with European Commission Joint Research Centre in Ispra, Radiation Warning Centre in Vienna and Meteoservice Budapest. (author)

  13. Environment monitoring and residents health condition monitoring of nuclear power plant Bohunice region

    International Nuclear Information System (INIS)

    Letkovicova, M.; Rehak, R.; Stehlikova, B.; Celko, M.; Hraska, S.; Klocok, L.; Kostial, J.; Prikazsky, V.; Vidovic, J.; Zirko, M.; Beno, T.; Mitosinka, J.

    1998-01-01

    The report contents final environment evaluation and selected characteristic of residents health physics of nuclear power plant Bohunice region. Evaluated data were elaborated during analytical period 1993-1997.Task solving which results are documented in this final report was going on between 1996- 1998. The report deals in individual stages with the following: Information obtaining and completing which characterize demographic situation of the area for the 1993-1997 period; Datum obtaining and completing which contain selected health physics characteristics of the area residents; Database structures for individual data archiving from monitoring and collection; Brief description of geographic information system for graphic presentation of evaluation results based on topographic base; Digital mapping structure description; Results and evaluation of radionuclide monitoring in environment performed by Environmental radiation measurements laboratory by the nuclear power plant Bohunice for the 1993-1997 period. Demographic situation evaluation and selected health physics characteristics of the area of nuclear power plant residents for the 1993-1997 period are summarized in the final part of the document. Monitoring results and their evaluation is processed in graph, table, text description and map output forms. Map outputs are processed in the geographic information system Arc View GIS 3.0a environment

  14. Radioactivity monitoring of the Irish marine environment 1985-86

    International Nuclear Information System (INIS)

    Cunningham, J.D.; O'Grady, J.; Rush, T.

    1988-01-01

    This report presents the results of the monitoring programme for the two-year period from January 1985 to December 1986. Information on the radioactive contamination of the marine environment is obtained from the analysis of environmental samples taken at a number of locations along the coastline and various sampling stations in the western Irish Sea. These usually include samples of surface seawater, sediment, seaweed, fish and shellfish. Estimates are presented of the individual and collective doses received by the Irish public from the consumption of fish and shellfish during the period 1985-1986. These doses are assessed in terms of the system of dose limitation recommended by the International Commission on Radiological Protection and embodied in the Basic Safety Standards Directive of the European Community

  15. Monitoring of health and environment by National Uranium Company (NUC)

    International Nuclear Information System (INIS)

    Georgescu, D.P.; Banciu, O

    1998-01-01

    Among the activities of geological survey, exploitation and processing of radioactive ore performed by National Uranium Company (NUC) a major attention is paid to personnel medical monitoring, to influences on the public health in the affected zones and also to the impact on environment, based on specific criteria and accomplished by medical and technical institutions having an adequate profile, in conformity with the enforced laws and with recommendations of international authorities on this field. Health monitoring of the active and retired personnel and of population from the affected sites by the NUC activities is done on the basis of a program established in co-operation with the Work Protection Department and the management of the company's subunits. The methodology used at present has the following three stages: 1. Periodical medical examination of the personnel including all the compulsory investigations requested by the Ministry of Health; 2. Annual epidemiology descriptive studies concerning the analysis of the personnel health state; 3. Analytical epidemiologic studies (retrospective and prospective) having the aim of surveying the radiation effects on the human target organs of the exposed personnel and also the impact on the public health in the influenced zones. At present the incidence of professional diseases liked to uranium is no longer a problem. Attention has to be focused to the diseases due to microclimate, noise, intensive physical effort and stress (non-specific chronic breathing diseases, arterial high blood pressure, heart diseases, digestive diseases and neuroses). The paper presents also the environmental factors investigated in connection with the importance which they have in radioactive contamination: air, water, soil, sediments, vegetation, and agricultural products. There are given the results of the tests performed on 25,000 samples and from more then 20,000 radiometric measurements performed between 1975 - 1997 in each subunit of

  16. Tritium monitoring in environment at ICIT Tritium Separation Facility

    International Nuclear Information System (INIS)

    Varlam, Carmen; Stefanescu, I.; Vagner, Irina; Faurescu, I.; Toma, A.; Dulama, C.; Dobrin, R.

    2008-01-01

    Full text: The Cryogenic Pilot is an experimental project developed within the national nuclear energy research program, which is designed to develop the required technologies for tritium and deuterium separation by cryogenic distillation of heavy water. The process used in this installation is based on a combination between liquid-phase catalytic exchange (LPCE) and cryogenic distillation. Basically, there are two ways that the Cryogenic Pilot could interact with the environment: by direct atmospheric release and through the sewage system. This experimental installation is located 15 km near the region biggest city and in the vicinity - about 1 km, of Olt River. It must be specified that in the investigated area there is an increased chemical activity; almost the entire Experimental Cryogenic Pilot's neighborhood is full of active chemical installations. This aspect is really essential for our study because the sewerage system is connected with the other three chemical plants from the neighborhood. For that reason we progressively established elements of an environmental monitoring program well in advance of tritium operation in order to determine baseline levels. The first step was the tritium level monitoring in environmental water and wastewater of industrial activity from neighborhood. In order to establish the base level of tritium concentration in the environment around the nuclear facilities, we investigated the sample preparation treatment for different types of samples: onion, green beams, grass, apple, garden lettuce, tomato, cabbage, strawberry and grapes. We used azeotropic distillation of all types of samples, the carrier solvent being toluene from different Romanian providers. All measurements for the determination of environmental tritium concentration were performed using liquid scintillation counting (LSC), with the Quantulus 1220 spectrometer. (authors)

  17. Monitoring of radionuclides in the environment - is chemistry still needed?

    International Nuclear Information System (INIS)

    Cooper, E.L.

    1989-01-01

    Improvements in gamma spectrometry have led to a decline in the use of radiochemical methods by environmental laboratories. Radiochemical methods are still required for radioisotopes which do not emit gamma rays (e.g. 89,90 Sr, 239,240 Pu, etc.); however, as the levels of these radioisotopes from weapons fallout declined in the 1970's and 1980's, the interest in them also declined. The changes which had occurred in analytical methodology became apparent after the Chernobyl accident when all the early measurements were obtained by gamma spectrometry and information on Sr isotopes and actinides only began to emerge some weeks later. The role of chemistry in monitoring begins with sampling because of speciation and matrix effects and extends through the radiochemical analysis. In some cases it may be necessary to determine speciation because of differences in dose conversion factors or environmental behavior. There is a need to improve radiochemical procedures and the IAEA has established in dose conversion factors or environmental behavior. There is a need to improve radiochemical procedures and the IAEA has established a new coordinated research program on rapid methods. Clearly, there still are chemical aspects to monitoring radionuclides in the environment, and these are discussed

  18. Neutron-activation method of monitoring of the environment

    International Nuclear Information System (INIS)

    Sattarov, G.S.; Muzafarov, A.M.; Komilov, J.M.; Kadirov, F.; Kist, A.A.

    2004-01-01

    Full text: Estimation of technogenic influences of the industrial enterprises on an environment, in particular, on ground and underground waters, was carried out by the fragmentary analysis of their element structure. In the report application of neutron-activation analysis (NAA) for monitoring an environment is considered. The total contents of elements was determined by NAA method with use of a reactor such as WWR-SM. Values of factors of correlation (K) are calculated with use of the computer, by special algorithm and reception of numerical values between 30 elements in the samples selected by a traditional technique from more than 600 points in area of activity GMZ-2. The developed technique has allowed to reveal elements indicators of technogenic (As, Ag, Sb, W, Au), mixed (Mo, Ba, Hg) and natural (Sc, Fe, Co, Ni, Rb, Cs, REE, Hf, Th, U) origins. Change of the total contents of elements in underground waters which were selected from observant chinks quarterly within three years is investigated. The technique of definition of forms of a presence of elements in underground and the sewage, based on electrodialysis division of ions with use nuclear (on a basis polyethyleneterephtalate film) filters with a diameter of pores of 0,16x0,2 micrometres is developed

  19. An artificial reality environment for remote factory control and monitoring

    Science.gov (United States)

    Kosta, Charles Paul; Krolak, Patrick D.

    1993-01-01

    Work has begun on the merger of two well known systems, VEOS (HITLab) and CLIPS (NASA). In the recent past, the University of Massachusetts Lowell developed a parallel version of NASA CLIPS, called P-CLIPS. This modification allows users to create smaller expert systems which are able to communicate with each other to jointly solve problems. With the merger of a VEOS message system, PCLIPS-V can now act as a group of entities working within VEOS. To display the 3D virtual world we have been using a graphics package called HOOPS, from Ithaca Software. The artificial reality environment we have set up contains actors and objects as found in our Lincoln Logs Factory of the Future project. The environment allows us to view and control the objects within the virtual world. All communication between the separate CLIPS expert systems is done through VEOS. A graphical renderer generates camera views on X-Windows devices; Head Mounted Devices are not required. This allows more people to make use of this technology. We are experimenting with different types of virtual vehicles to give the user a sense that he or she is actually moving around inside the factory looking ahead through windows and virtual monitors.

  20. Radioactivity monitoring of the Irish marine environment 1993 to 1995

    International Nuclear Information System (INIS)

    Pollard, D.; Long, S.; Hayden, E.; Smith, V.; Ryan, T.P.; Dowdall, A.; McGarry, A.; Cunningham, J.D.

    1996-10-01

    This report presents the results of the marine radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland during the period 1993 to 1995. The principal objective of this programme is to assess the exposure to the Irish population arising from radioactive contamination in the Irish marine environment and to estimate the risks to human health arising from such exposure. In addition, the programme aims to assess the distribution of the significant contaminating radionuclides in the marine environment and to identify tends with a view to assessing possible future effects. The results show that by 1995 the mean concentration of caesium-137 in fish landed at north-east ports had fallen to 1.6 Bq/kg, from a figure of 68 Bq/kg in 1979-82 and 3.0 Bq/kg in 1993. A similar decline is evident for seawater, sediment and seaweed. In addition, the Irish Sea data show the progressive dilution of artificial radioactivity with increasing distance from Sellafield

  1. Integrated site investigation and groundwater monitoring in an urban environment

    Science.gov (United States)

    Weatherl, R. K.

    2017-12-01

    Understanding groundwater dynamics around cities and other areas of human influence is of crucial importance for water resource management and protection, especially in a time of environmental and societal change. The human environment presents a unique challenge in terms of hydrological characterization, as the water cycle is generally artificialized and emissions of treated waste and chemical products into the surface- and groundwater system tend to disrupt the natural aqueous signature in significant ways. This project presents an integrated approach for robust characterization and monitoring of an urban aquifer which is actively exploited for municipal water supply. The study is carried out in the town of Fehraltorf, in the canton of Zürich, Switzerland. This particular town encompasses industrial and agricultural zones in addition to its standard urban setting. A minimal amount of data exist at this site, and the data that do exist are spatially and temporally sparse. Making use of traditional hydrogeological methods alongside evolving and emerging technologies, we aim to identify sources of contamination and to define groundwater flow and solute transport through space and time. Chemical and physical indicator parameters are identified for tracing contaminations including micropollutants and plant nutrients. Wireless sensors are installed for continuous on-line monitoring of essential parameters (electrical conductivity, temperature, water level). A wireless sensor network has previously been installed in the sewer system of the study site, facilitating investigation into interactions between sewer water and groundwater. Our approach illustrates the relations between land use, climate, rainfall dynamics, and the groundwater signature through time. At its conclusion, insights gained from this study will be used by municipal authorities to refine protective zones around pumping wells and to direct resources towards updating practices and replacing

  2. Tritium monitoring in the environment of the French territory

    Energy Technology Data Exchange (ETDEWEB)

    Leprieur, F.; Roussel-Debet, S.; Pierrard, O.; Tournieux, D.; Boissieux, T.; Caldera-Ideias, P. [Institut de radioprotection et de surete nucleaire (France)

    2014-07-01

    Introduction: Radioactive releases in the environment from civilian and military nuclear facilities have significantly decreased over the last few decades, except for discharges of tritium which are forecast to increase due to changes in the fuel management in power plants and in the longer term by new tritium-emitting units (fusion reactors). In the aim to perform its radiological monitoring mission throughout the French territory, IRSN uses and develops advanced technology equipment to sample and to analyze tritium in the different environmental compartments. Methodology: IRSN uses bubblers to collect both tritium vapour (HTO) and gaseous tritium (mainly HT) in the air. Another method, developed by IRSN, consists in directly sampling the water vapour in the air by condensing in a cold trap and more recently with passive sampler. In continental and marine surface water, samples are usually collected by automatic water samplers. Instantaneous surface water samples are also collected by grab sample devices. In addition, IRSN conducts animal and plant samples near French nuclear facilities. Natural origin and tritium remaining from testing of nuclear weapons In the atmosphere, the background levels of tritium of 1 to 2 Bq/L measured in water vapour, equivalent to an activity of 0.01 to 0.02 Bq/m{sup 3} of air. In fresh waters, the tritium activity currently ranges between 1 and 3 Bq/L of water. In the marine environment, tritium emitted during nuclear weapon tests has been totally 'diluted' in cosmogenic tritium and concentration levels at the surface have remained around 0.1 to 0.2 Bq/L. In biological matrices, total tritium concentration range from 1 to 3 Bq/kg f.w. with a variable proportion of free and organically bounded forms. Tritium around nuclear facilities: Close to facilities releasing more than 2x10{sup 13} Bq/year of gaseous tritium, higher activity levels, ranging from a few tens to a few hundred Bq/L, are observed in the atmospheric and

  3. Cesium-137 monitoring of aquatic and terrestrial environment in Goiania

    International Nuclear Information System (INIS)

    Godoy, J.N.O.; Guimaraes, J.R.D.; Gouvea, V.A.; Rochedo, E.R.R.

    1988-01-01

    During the Goiania radiological accident, aprox. 1200 Ci of Cs - 137 were inadvertently manipulated and an unknown fraction of this total was available for environmental dispertion during at least 6 weeks, before efficient remedial action could be undertaken. The main dispersion pathways were rainwater run-off and soil ressuspension and further deposition. Cs-137 monitoring in the local environment started in the first week of October, including to date aprox. 1300 measurements of soil, vegetable (fruits and kitchen-gardens), ground and drinking water, sediments and fish, aerosol, precipitation and external dose measurement with TL dosimeters, in the surroundings of the main contamination spots. Until the conclusion of de-contamination activities in late December, the ranges of Cs-137 in a 50m radius of evacuated areas were as follows: 10 2 -10 4 Bq/Kg for surface soils and edible vegetables, 10 0 -10 1 mBq/m 3 in air and 10 Bq/l in all water types. River sediment and fish 5-10 Km downstream the accident are ranged respectively 10 2 -10 3 and 10 2 /Kg. These data indicated the pathways and locations for intervention for further reduction of radiation exposure. This intervention consisted mainly in tree-tipping and surface soil removal. (author) [pt

  4. Acoustical monitoring of diesel engines in reverberant environment

    International Nuclear Information System (INIS)

    Mein, M.

    1995-10-01

    The feed-back knowledge of emergency diesel generators in nuclear power plants shows that some malfunctions, mainly affecting fuel-injection or distribution system of the engine can be heard and detected by experienced maintenance agents. This study consists in the feasibility,v of acoustical monitoring of those diesel engines, taking into account the reverberant environment of the machine. The operating cycle of the diesel is composed of transient events (injection, combustion, valve closure...) which generate highly non stationary acoustical signals. The detection of a malfunction appearing on such transients requires the use of adapted signal processing techniques. Visual analysis of the phenomena is first proceeded using time-frequency and time-scale representations. The second step will be parametric modeling of acoustical signatures for the extraction of characteristic parameters, in order to characterize the fault and to use an automatic classification system. The lest part of the study will concern the evaluation of the robustness of the detection methods in regard to acoustical reverberation. (author). 10 refs., 6 figs

  5. Radioactivity monitoring of the Irish marine environment 1996 and 1997

    International Nuclear Information System (INIS)

    Long, S.; Pollard, D.; Hayden, E.; Smith, V.; Fegan, M.; Ryan, T.P.; Dowdall, A.; Cunningham, J.D.

    1998-07-01

    This report presents the results of the marine radioactivity monitoring programme carried out be the Radiological Protection Institute of Ireland (RPII) during 1996 and 1997. The primary objective of the programme is to assess the exposure to the Irish population resulting from radioactive contamination of the Irish marine environment and to estimate the risks to health from this exposure. Discharges from the British Nuclear Fuels (BNFL) reprocessing plant at Sellafield continue to be the principal source of this contamination. Approximately 300 samples of fish, shellfish, seaweed, seawater and sediment were collected each year. The samples were analysed for a range of contaminating radionuclides at the Institute's radioanalytical laboratory. The results show that the radionuclide of greatest dosimetric significance continues to be caesium-137. Since 1994 the commissioning and operation of new facilities at Sellafield have resulted in an increase in the discharges of technetium-99 to the Irish Sea. This has been reflected in an increase in the activity concentration of this radionuclide at all east coast sampling sites during the reporting period. The main pathway contributing to the exposure of the Irish public is the consumption of seafood. The committed effective dose to heavy consumers of seafood due to artificial radionuclides in 1996 was 1.6 μSv and in 1997 was 1.4 μSv. in 1996 was 1.6 μSv and in 1997 was 1.4 μSv

  6. Annual report on radioactive discharges from Winfrith and monitoring the environment 1987

    International Nuclear Information System (INIS)

    1988-04-01

    The 1987 Annual Report on radioactive discharges from Winfrith Atomic Energy Establishment and monitoring of the environment is given. The report covers waste discharges to the sea and the earth atmosphere and the associated environmental monitoring. (UK)

  7. Advanced SEM imaging

    International Nuclear Information System (INIS)

    Joy, D. C.; Newbury, D. E.

    1998-01-01

    The scanning electron microscope (SEM) represents the most promising tool for metrology, defect review, and for the analysis of ULSI structures, but both fundamental problems such as electron-solid interactions, and practical considerations such as electron-optical constraints, are now setting a limit to performance. This paper examines the directions in which an advanced SEM might be developed to overcome these constraints. The SEM also offers considerable promise as a tool for the high spatial resolution X-ray microanalysis, especially for those situations where a thin cross-section is not practical and first surface analysis is required. The ways in which this capability can be incorporated in an advanced SEM are examined

  8. Advanced SEM imaging

    International Nuclear Information System (INIS)

    Joy, D.C.; Newbury, D.E.; Newbury, D.E.

    1998-01-01

    The scanning electron microscope (SEM) represents the most promising tool for metrology, defect review, and for the analysis of ULSI structures, but both fundamental problems such as electron-solid interactions, and practical considerations such as electron-optical constraints, are now setting a limit to performance. This paper examines the directions in which an advanced SEM might be developed to overcome these constraints. The SEM also offers considerable promise as a tool for the high spatial resolution X-ray microanalysis, especially for those situations where a thin cross-section is not practical and first surface analysis is required. The ways in which this capability can be incorporated in an advanced SEM are examined. copyright 1998 American Institute of Physics

  9. Radioactivity monitoring of the Irish marine environment 1998 and 1999

    International Nuclear Information System (INIS)

    Ryan, T.P.; Long, S.; Dowdall, A.; Hayden, E.; Smith, V.; Fegan, M.; Sequeira, S.; Pollard, D.; Cunningham, J.D.

    2000-09-01

    The safety of the food chain and the protection of the environment are prime concerns of the Irish public. This report presents the results of the marine radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland (RPII) during 1998 and 1999. The primary objective of the programme is to assess the exposure of the Irish population resulting from radioactive contamination of the Irish marine environment and to estimate the risks to health from this exposure. Discharged radioactive waste from the British Nuclear Fuels plc (BNFL) reprocessing plant at Sellafield continues to be the dominant source of this contamination. In particular, the remobilisation from sediments of historic discharges makes an important contribution to the levels of radioactivity in the seawater of the western Irish Sea. Approximately 300 samples of fish, shellfish, seaweed, seawater and sediment were collected in 1998 and again in 1999. Both the Marine Institute and the Department of the Marine and Natural Resources assisted the Institute with this sampling. The samples were analysed for a range of contaminating radionuclides at the Institute's radio-analytical laboratory. The results show that the radionuclide of greatest dosimetric significance continues to be caesium-137. The activity concentration of this radionuclide in the Irish marine environment has remained relatively stable since the mid 1990s but at a lower level than that observed during the previous two decades. Along the Irish coastline the highest activity concentrations observed are in the north-east. Since 1994 the commissioning and operation of new facilities at Sellafield have resulted in an increase in the discharges of technetium-99 to the Irish Sea. This has been reflected in an increase in the activity concentrations of this radionuclide at all east coast sampling sites between 1994 and 1999. However, the low radiotoxicity of technetium-99 means that it is generally of lesser

  10. Radioactivity monitoring of the Irish marine environment 1998 and 1999

    International Nuclear Information System (INIS)

    Ryan, T.; Long, S.; Dowdall, A.

    2000-09-01

    The safety of the food chain and the protection of the environment are prime concerns of the Irish public. This report presents the results of the marine radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland (RPII) during 1998 and 1999. The primary objective of the programme is to assess the exposure of the Irish population resulting from radioactive contamination of the Irish marine environment and to estimate the risks to health from this exposure. Discharged radioactive waste from the British Nuclear Fuels plc (BNFL) reprocessing plant at Sellafield continues to be the dominant source of this contamination. In particular, the remobilization from sediments of historic discharges makes an important contribution to the levels of radioactivity in the seawater of the western Irish Sea. Approximately 300 samples of fish, shellfish, seaweed, seawater and sediment were collected in 1998 and again in 1999. Both the Marine Institute and the Department of the Marine and Natural Resources assisted the Institute with this sampling. The samples were analysed for a range of contaminating radionuclides at the Institute's radio-analytical laboratory. The results show that the radionuclide of greatest dosimetric significance continues to be caesium-137. The activity concentration of this radionuclide in the Irish marine environment has remained relatively stable since the mid 1990s but at a lower level than that observed during the previous two decades. Along the Irish coastline the highest activity concentrations observed are in the north-east. Since 1994 the commissioning and operation of new facilities at Sellafield have resulted in an increase in the discharges of technetium-99 to the Irish Sea. This has been reflected in an increase in the activity concentrations of this radionuclide at all east coast sampling sites between 1994 and 1999. However, the low radiotoxicity of technetium-99 means that it is generally of lesser

  11. Annual report on radioactive discharges and monitoring of the environment 1993. V. 2: Certificates of authorisation and environmental monitoring programmes

    International Nuclear Information System (INIS)

    1994-01-01

    British Nuclear Fuels plc's Certificates of Authorisation, under which it operates, are reproduced in the second volume of the 1993 Annual Report on Radioactive Discharges and Monitoring of the Environment. The report also includes environmental monitoring programmes relating to discharge authorisation for each of the Sellafield, Drigg, Chapelcross, Springfields and Capenhurst sites. (UK)

  12. Biomonitors of urban air pollution: Magnetic studies and SEM observations of corticolous foliose and microfoliose lichens and their suitability for magnetic monitoring

    International Nuclear Information System (INIS)

    Chaparro, Marcos A.E.; Lavornia, Juan M.; Chaparro, Mauro A.E.; Sinito, Ana M.

    2013-01-01

    This study explored the suitability of available lichen species as air pollution biomonitors and assessed their potential for magnetic monitoring in cities. Several lichens on tree bark were collected in urban and industrial sites from Tandil city, as well as control sites. The results showed that magnetite-like minerals were the main magnetic carriers in all sites and samples. However, the concentration varied between clean and polluted sites. In addition, magnetic-grain size-distribution showed clear differences between sites. Observations by scanning electron microscopy showed different particles in a variety of shapes and grain sizes; moreover, the presence of iron oxides and several toxic elements was detected by energy dispersive spectroscopy analysis. Although eleven lichen species were identified that appeared suitable for use as air-pollution monitors, three of them, Parmotrema pilosum, Punctelia hipoleucites and Dirinaria picta, occurred more frequently in the area, thus constituting appropriate species for future monitoring in the study area. - Highlights: ► Magnetite-like minerals are the main carriers in lichen samples. ► Magnetic concentration and grain sizes vary between polluted and control sites. ► Different pollution loads were classified from pcoorda and K-means clustering analysis. ► Parmotrema pilosum, Punctelia hipoleucites and Dirinaria picta appear to be suitable air pollution monitors. - Lichen species are airborne pollutant collectors that are well-distributed in some urban areas and allow effective magnetic monitoring at low cost in cities.

  13. Integrated Monitoring AWAReness Environment (IM-AWARE), Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — American GNC Corporation (AGNC) and Louisiana Tech University (LaTECH) are proposing a significant breakthrough technology, the Integrated Monitoring AWAReness...

  14. Applications of wireless sensor networks for monitoring oil and gas onshore fields; Aplicacoes de redes de sensores sem fio em monitoramento de pocos petroliferos terrestres

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Ivanovitch Medeiros D. da; Oliveira, Luiz Affonso H. Guedes de [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2008-07-01

    The major part of onshore oil wells monitoring currently is based on wireless solutions. However these solutions employ old technologies based on analog radios and inefficient communication topologies. On the other hand, technologies based on digital radios can provide more efficient solutions related to energy consumption, security and fault tolerance. Thus, this paper investigates the Wireless Sensor Network as an approach to onshore oil wells monitoring. Reliability, energy consumption and communication delay in a mesh topology will be used as metrics to validate the proposal using the simulation tool NS-2. (author)

  15. Annual report on radioactive discharges and monitoring of the environment 1992. V. 1

    International Nuclear Information System (INIS)

    1993-01-01

    This Annual Report supplements the Company's Health and Safety Annual Report by providing more detailed information on radioactive discharges, monitoring of the environment and critical group doses. BNFL has published Annual Reports on Radioactive Discharges and Monitoring of the Environment, covering the period from 1977 to the present. For 1990 this report has been sub-divided into two complementary parts. Volume I includes annual data for each of the Company sites on radioactive discharges into the environment and the associated environmental monitoring programmes. Volume II reproduces the Certificates of Authorisation under which the Company operates and the statutory environmental monitoring programmes which relate to them. (author)

  16. Annual report on radioactive discharges and monitoring of the environment 1990. V. 2

    International Nuclear Information System (INIS)

    1991-01-01

    This Annual Report supplements the Company's Health and Safety Annual Report by providing more detailed information on radioactive discharges, monitoring of the environment and critical group doses. BNFL has published Annual Reports on Radioactive Discharges and Monitoring of the Environment, covering the period from 1977 to the present. For 1990 this report has been sub-divided into two complementary parts. Volume I includes annual data for each of the Company sites on radioactive discharges into the environment and the associated environmental monitoring programmes. Volume II reproduces the Certificates of Authorisation under which the Company operates and the statutory environmental monitoring programmes which relate to them. (author)

  17. Annual report on radioactive discharges and monitoring of the environment 1990. V. 1

    International Nuclear Information System (INIS)

    1991-01-01

    This Annual Report supplements the Company's Health and Safety Annual Report by providing more detailed information on radioactive discharges, monitoring of the environment and critical group doses. BNFL has published Annual Reports on Radioactive Discharges and Monitoring of the Environment, covering the period from 1977 to the present. For 1990 this report has been sub-divided into two complementary parts. Volume I includes annual data for each of the Company sites on radioactive discharges into the environment and the associated environmental monitoring programmes. Volume II reproduces the Certificates of Authorisation under which the Company operates and the statutory environmental monitoring programmes which relate to them. (author)

  18. Monitoring aquatic environment pollution: a major component of environment management systems

    International Nuclear Information System (INIS)

    Khan, I.H.; Khan, M.H.; Sheikh, I.M.

    1999-01-01

    The paper is based on the international experiences mostly of the UK (United Kingdom) and Europe on monitoring aquatic pollution and controlling water pollution which have a long history of the legislation involved. The U.K. control of water pollution and regulatory laws are very effective as in shown by the fact that 96 percent of rivers in England and Wales are suitable for potable supplies with conventional water treatment. Current British legislation is basically contained n the 1951, 1960 and 1974 acts of parliament in the U.K. A common feature of all this environment legislation is the high level of consultation which has taken place between government and all concerned and al those concerned in the development of legislation and drawing up regulations etc. and involved in implementation of them. Similarly considerable discussion takes place with the controlling authorities by dischargers over the detailed implementation of legislation in the U.K. Consequently these harmonious attitudes have been responsible for the effectiveness of the U.K. legislation. In the U.K. control of discharges of industrial effluents to sewers and to all natural waters including underground water is vested in the regional water authorities, which on application, issue consent permitting discharges of industrial effluents to sewers and to all natural waters including underground waters in vested in the regional water authorities, which on application, issue consent permitting discharges to be made subject to conditions and limitations in the consent/authorisation/approval. The paper critically reviews major aspects of the philosophy of aquatic pollution control and monitoring, as statistics reveal deadly state of liquid effluent contamination water bodies in Pakistan. Without prompt installation of treatment plants we may face a tragedy of catastrophic magnitude. (author)

  19. Building of effluence and environment monitoring capability of uranium mining and metallurgy in China

    International Nuclear Information System (INIS)

    Li Xianjie; Hu Penghua; Duan Jianchen; Xue Jianxin

    2014-01-01

    The status of effluence and environmental monitoring capability of nine uranium mining and metallurgy corporations in operation in China was investigated and analyzed. The results show that there exist some problems in all corporations such as imperfect monitoring plan, ineligible analyst, aging equipment, insufficient analysis capacity, lack of good detection limit. In order to solve the problems, several steps have been taken by Department of Safety and Environment Protection and Department of Geology and Mining (CNNC) in three years, including establishing three-level monitoring sys- tem, equipping corresponding monitoring instrument, holding three training classes, enhancing the analyst capacity, publishing the model for effluence and environment monitoring capability of uranium mining and metallurgy and carrying out comparison on monitoring of U and Ra in water, which greatly improved effluence and environment monitoring capability of uranium mining and metallurgy. (authors)

  20. Spin-polarized SEM

    International Nuclear Information System (INIS)

    Konoto, Makoto

    2007-01-01

    Development of highly effective evaluation technology of magnetic structures on a nanometric scale is a key to understanding spintronics and related phenomena. A high-resolution spin-polarized scanning electron microscope (spin SEM) developed recently is quite suitable for probing such nanostructures because of the capability of analyzing local magnetization vectors in three dimensions. Utilizing the spin SEM, a layered antiferromagnetic structure with the 1nm-alternation of bilayer-sheet magnetization has been successfully resolved. The real-space imaging with full analysis of the temperature-dependent magnetization vectors will be demonstrated. (author)

  1. Annual report on radioactive discharges and monitoring of the environment 1991. V. 1

    International Nuclear Information System (INIS)

    1992-01-01

    This Annual Report supplements and updates British Nuclear Fuel plc's Health and Safety and the Environment Annual Report by providing more detailed information on radioactive discharges, monitoring of the environment and critical groups doses. BNFL has published Annual Reports on Radioactive Discharges and Monitoring of the Environment since 1977. This year the report is again sub-divided into two complementary volumes. Volume I includes, for each of the Company's sites, annual data on radioactive discharges into the environment and the associated environmental monitoring programmes. Critical groups doses for each site are presented in summary tables at the beginning of each chapter. (author)

  2. Monitoring the abundance of plastic debris in the marine environment

    OpenAIRE

    Ryan, Peter G.; Moore, Charles J.; van Franeker, Jan A.; Moloney, Coleen L.

    2009-01-01

    Plastic debris has significant environmental and economic impacts in marine systems. Monitoring is crucial to assess the efficacy of measures implemented to reduce the abundance of plastic debris, but it is complicated by large spatial and temporal heterogeneity in the amounts of plastic debris and by our limited understanding of the pathways followed by plastic debris and its long-term fate. To date, most monitoring has focused on beach surveys of stranded plastics and other litter. Infreque...

  3. Ambient radioactivity monitoring V: Marine environment, fish and marine organisms

    International Nuclear Information System (INIS)

    Wedekind, C.; Kanisch, G.

    1996-01-01

    The sea, originally thought to have an almost unlimited capacity of uptake of pollutants due to its water volumes available for dilution, was shown by growing insight into the physical, chemical and ecologic interdependencies to be a sensitive ecosystem. Its limits to cope with growing pollution are increasingly becoming clear, and this is a particular reason to perform radioactivity monitoring of the sea water, as radioactivity is transferred to the marine organisms. Organisms selected for monitoring are fish and crustaceans. (orig.) [de

  4. Applications of Wireless Sensor Networks in Marine Environment Monitoring: A Survey

    Science.gov (United States)

    Xu, Guobao; Shen, Weiming; Wang, Xianbin

    2014-01-01

    With the rapid development of society and the economy, an increasing number of human activities have gradually destroyed the marine environment. Marine environment monitoring is a vital problem and has increasingly attracted a great deal of research and development attention. During the past decade, various marine environment monitoring systems have been developed. The traditional marine environment monitoring system using an oceanographic research vessel is expensive and time-consuming and has a low resolution both in time and space. Wireless Sensor Networks (WSNs) have recently been considered as potentially promising alternatives for monitoring marine environments since they have a number of advantages such as unmanned operation, easy deployment, real-time monitoring, and relatively low cost. This paper provides a comprehensive review of the state-of-the-art technologies in the field of marine environment monitoring using wireless sensor networks. It first describes application areas, a common architecture of WSN-based oceanographic monitoring systems, a general architecture of an oceanographic sensor node, sensing parameters and sensors, and wireless communication technologies. Then, it presents a detailed review of some related projects, systems, techniques, approaches and algorithms. It also discusses challenges and opportunities in the research, development, and deployment of wireless sensor networks for marine environment monitoring. PMID:25215942

  5. SEM microcharacterization of semiconductors

    CERN Document Server

    Holt, D B

    1989-01-01

    Applications of SEM techniques of microcharacterization have proliferated to cover every type of material and virtually every branch of science and technology. This book emphasizes the fundamental physical principles. The first section deals with the foundation of microcharacterization in electron beam instruments and the second deals with the interpretation of the information obtained in the main operating modes of a scanning electron microscope.

  6. Marketing Management: Monitoring the International Environment Factors Using Global Maps

    Directory of Open Access Journals (Sweden)

    Štěpán Kala

    2015-01-01

    Full Text Available The article discusses the issue of the global marketing environment in line with the factors determining its external conditions. The aim is to specify the marketing-environment indicators in the international context and interpret the use of geographical maps illustratively documenting the differences of particular parameters in various parts of the global market. The research-results help update the theoretical framework of global environment factors. These data are also important for practice. Many enterprises consider the question of optimising their sources and directing their goals towards the opportunities available thanks to global markets. The global environment mapping is thereby an important basis for the marketing activities whose implementation across national boundaries is going to be mainly influenced by peculiarities of the environment involving foreign markets and their changes.

  7. Monitoring the abundance of plastic debris in the marine environment.

    Science.gov (United States)

    Ryan, Peter G; Moore, Charles J; van Franeker, Jan A; Moloney, Coleen L

    2009-07-27

    Plastic debris has significant environmental and economic impacts in marine systems. Monitoring is crucial to assess the efficacy of measures implemented to reduce the abundance of plastic debris, but it is complicated by large spatial and temporal heterogeneity in the amounts of plastic debris and by our limited understanding of the pathways followed by plastic debris and its long-term fate. To date, most monitoring has focused on beach surveys of stranded plastics and other litter. Infrequent surveys of the standing stock of litter on beaches provide crude estimates of debris types and abundance, but are biased by differential removal of litter items by beachcombing, cleanups and beach dynamics. Monitoring the accumulation of stranded debris provides an index of debris trends in adjacent waters, but is costly to undertake. At-sea sampling requires large sample sizes for statistical power to detect changes in abundance, given the high spatial and temporal heterogeneity. Another approach is to monitor the impacts of plastics. Seabirds and other marine organisms that accumulate plastics in their stomachs offer a cost-effective way to monitor the abundance and composition of small plastic litter. Changes in entanglement rates are harder to interpret, as they are sensitive to changes in population sizes of affected species. Monitoring waste disposal on ships and plastic debris levels in rivers and storm-water runoff is useful because it identifies the main sources of plastic debris entering the sea and can direct mitigation efforts. Different monitoring approaches are required to answer different questions, but attempts should be made to standardize approaches internationally.

  8. The monitoring of radioactive contamination and radiation exposure in the environment in Germany- tasks, techniques, realizations

    International Nuclear Information System (INIS)

    Bayer, A.

    1998-01-01

    A brief historical account of the development of the monitoring of radioactivity in the environment in Germany is given. The aims of monitoring and the tasks, classified according to the possible sources of release, are presented and the methods required are described. The monitoring systems, set up on the basis of different legal principles, are presented and the technical realization of these including their current state of development, is described. Finally, an account is given of the coordination of the national monitoring systems which is at present in progress, as well as of the integration of these monitoring systems into international monitoring and information networks. (author)

  9. Radioactivity monitoring of the Irish marine environment 2000 and 2001

    International Nuclear Information System (INIS)

    Ryan, T.P.; McMahon, C.A.; Dowdall, A.

    2003-04-01

    This report presents the results of the marine radioactivity monitoring programme carried out by the Radiological Protection Institute of Ireland (RPII) during 2000 and 2001. The primary objective of the programme is to assess the exposure of the Irish population resulting from radioactive contamination of the Irish marine environment and to estimate the risks to health from this exposure. Discharged radioactive waste from the British Nuclear Fuels plc (BNFL) reprocessing plant at Sellafield in Cumbria in the North West of England continues to be the dominant source of this contamination. In particular, the remobilisation from sediments of historic discharges makes an important contribution to the levels of radioactivity in the seawater of the western Irish Sea. Approximately 300 samples of fish, shellfish, seaweed, seawater and sediment were collected in 2000 and again in 2001. Both the Marine Institute and the Department of Communications, Marine and Natural Resources assisted the Institute with this sampling. The samples were analysed for a range of radionuclides at the Institute's radio-analytical laboratory. The results show that the artificial radionuclide of greatest dosimetric significance continues to be caesium-137. The activity concentration of this radionuclide in the Irish marine environment has remained relatively stable since the mid 1990s but at a lower level than that observed during the previous two decades. Along the Irish coastline the highest activity concentrations observed are in the north-east. Since 1994 the commissioning and operation of new facilities at Sellafield have resulted in an increase in the discharges of technetium-99 to the Irish Sea. This has been reflected in an increase in the activity concentrations of this radionuclide at all east coast sampling sites. However, the low radiotoxicity of technetium-99 means that it is generally of lesser radiological significance than caesium-137. The main pathway contributing to the

  10. Continuous monitoring for airborne alpha emitters in a dusty environment

    International Nuclear Information System (INIS)

    Seiler, F.A.; Newton, G.J.; Guilmette, R.A.

    1988-01-01

    Disposal of radioactive wastes in underground facilities requires continuous monitoring for airborne radioactive materials, both on the surface and underground. In addition to a natural background of nonradioactive and radioactive aerosols, there may be a sizeable dust contribution from ongoing work such as mining and vehicular traffic. In the monitoring of alpha-emitting radionuclides, these aerosols may lead to self-absorption in the source and a deterioration of the energy spectrum of the detected alpha particles. In this paper, the influence of a realistic background aerosol on the performance of an alpha monitoring system is evaluated theoretically. It is shown that depositing alpha emitters and background aerosol on a surface for counting leads rapidly to a considerable loss of counts, a deterioration of the alpha spectra, an eventual saturation of the count rates, and interference from the natural background of Rn daughters

  11. Monitoring coastal wetlands in a highly dynamic tropical environment

    International Nuclear Information System (INIS)

    Saynor, M.J.; Finlayson, C.M.; Spiers, A.; Eliot, I.

    2001-01-01

    The Alligator Rivers Region in the wet-dry tropics of northern Australia has been selected by government and collaborating agencies as a key study area for the monitoring of natural and human-induced coastal change. The Region contains the floodplain wetlands of Kakadu National Park which have been recognised internationally for their natural and cultural heritage value. A coastal monitoring program for assessing and monitoring environmental change in the Alligator Rivers Region has been established at the Environmental Research Institute of the Supervising Scientist. This program has developed a regional capacity to measure and assess change on the wetlands, floodplains and coastline within the region. Field assessment and monitoring procedures have been developed for the program. The assessment procedures require use of georeferencing and data handling techniques to facilitate comparison and relational overlay of a wide variety of information. Monitoring includes regular survey of biophysical and cultural processes on the floodplains; such as the extension of tidal creeks and mangroves, shoreline movement, dieback in Melaleuca wetlands, and weed invasion of freshwater wetlands. A differential Global Positioning System is used to accurately georeference spatial data and a Geographic Information System is then used to store and assess information. The assessment and monitoring procedures can be applied to the wet-dry tropics in general. These studies are all particularly pertinent with the possibility of greenhouse gases causing global warming and potential sea-level rise, a major possible threat to the valued wetlands of Kakadu National Park, and across the wet-dry tropics in general

  12. Long term pipeline monitoring in geomechanically sensitive environments

    Energy Technology Data Exchange (ETDEWEB)

    Weir-Jones, I.; Sun, M. [Weir-Jones Engineering Consultants Ltd. (Canada)

    2011-07-01

    In the oil industry, monitoring pipeline structural integrity is necessary for both regulatory and environmental purposes. Weir-Jones Engineering Consultants developed an automated structural integrity monitoring (SIM) system, data on strain, displacement and temperature are continuously acquired and automatically transmitted to the monitoring personnel. The aim of this paper is to present this technology and its implementation on one of Inter Pipeline Fund's lines as well. The automated SIM equipment was installed on a new 42'' line at the crossing of the Clearwater River close to Fort McMurray. Results showed that this technology is a good way to monitor pipelines in remote locations, environmentally sensitive areas, river and embankment crossings and in locations where external forces can put the pipeline at risk; but it should not be used otherwise as that would not be cost effective. This paper described the developed automated SIM and showed that it should only be used in specific locations to be cost effective.

  13. Mobile monitoring and embedded control system for factory environment.

    Science.gov (United States)

    Lian, Kuang-Yow; Hsiao, Sung-Jung; Sung, Wen-Tsai

    2013-12-17

    This paper proposes a real-time method to carry out the monitoring of factory zone temperatures, humidity and air quality using smart phones. At the same time, the system detects possible flames, and analyzes and monitors electrical load. The monitoring also includes detecting the vibrations of operating machinery in the factory area. The research proposes using ZigBee and Wi-Fi protocol intelligent monitoring system integration within the entire plant framework. The sensors on the factory site deliver messages and real-time sensing data to an integrated embedded systems via the ZigBee protocol. The integrated embedded system is built by the open-source 32-bit ARM (Advanced RISC Machine) core Arduino Due module, where the network control codes are built in for the ARM chipset integrated controller. The intelligent integrated controller is able to instantly provide numerical analysis results according to the received data from the ZigBee sensors. The Android APP and web-based platform are used to show measurement results. The built-up system will transfer these results to a specified cloud device using the TCP/IP protocol. Finally, the Fast Fourier Transform (FFT) approach is used to analyze the power loads in the factory zones. Moreover, Near Field Communication (NFC) technology is used to carry out the actual electricity load experiments using smart phones.

  14. Gene-environment interaction and biological monitoring of occupational exposures

    International Nuclear Information System (INIS)

    Hirvonen, Ari

    2005-01-01

    Biological monitoring methods and biological limit values applied in occupational and environmental medicine have been traditionally developed on the assumption that individuals do not differ significantly in their biotransformation capacities. It has become clear, however, that this is not the case, but wide inter-individual differences exist in the metabolism of chemicals. Integration of the data on individual metabolic capacity in biological monitoring studies is therefore anticipated to represent a significant refinement of the currently used methods. We have recently conducted several biological monitoring studies on occupationally exposed subjects, which have included the determination of the workers' genotypes for the metabolic genes of potential importance for a given chemical exposure. The exposure levels have been measured by urine metabolites, adducts in blood macromolecules, and cytogenetic alterations in lymphocytes. Our studies indicate that genetic polymorphisms in metabolic genes may indeed be important modifiers of individual biological monitoring results of, e.g., carbon disulphide and styrene. The information is anticipated to be useful in insuring that the workplace is safe for everyone, including the most sensitive individuals. This knowledge could also be useful to occupational physicians, industrial hygienists, and regulatory bodies in charge of defining acceptable exposure limits for environmental and/or occupational pollutants

  15. Monitoring the abundance of plastic debris in the marine environment

    NARCIS (Netherlands)

    Ryan, P.G.; Moore, C.J. C.J.; Franeker, van J.A.; Moloney, C.L.

    2009-01-01

    Plastic debris has significant environmental and economic impacts in marine systems. Monitoring is crucial to assess the efficacy of measures implemented to reduce the abundance of plastic debris, but it is complicated by large spatial and temporal heterogeneity in the amounts of plastic debris and

  16. Mobile Monitoring and Embedded Control System for Factory Environment

    Science.gov (United States)

    Lian, Kuang-Yow; Hsiao, Sung-Jung; Sung, Wen-Tsai

    2013-01-01

    This paper proposes a real-time method to carry out the monitoring of factory zone temperatures, humidity and air quality using smart phones. At the same time, the system detects possible flames, and analyzes and monitors electrical load. The monitoring also includes detecting the vibrations of operating machinery in the factory area. The research proposes using ZigBee and Wi-Fi protocol intelligent monitoring system integration within the entire plant framework. The sensors on the factory site deliver messages and real-time sensing data to an integrated embedded systems via the ZigBee protocol. The integrated embedded system is built by the open-source 32-bit ARM (Advanced RISC Machine) core Arduino Due module, where the network control codes are built in for the ARM chipset integrated controller. The intelligent integrated controller is able to instantly provide numerical analysis results according to the received data from the ZigBee sensors. The Android APP and web-based platform are used to show measurement results. The built-up system will transfer these results to a specified cloud device using the TCP/IP protocol. Finally, the Fast Fourier Transform (FFT) approach is used to analyze the power loads in the factory zones. Moreover, Near Field Communication (NFC) technology is used to carry out the actual electricity load experiments using smart phones. PMID:24351642

  17. Mobile Monitoring and Embedded Control System for Factory Environment

    Directory of Open Access Journals (Sweden)

    Kuang-Yow Lian

    2013-12-01

    Full Text Available This paper proposes a real-time method to carry out the monitoring of factory zone temperatures, humidity and air quality using smart phones. At the same time, the system detects possible flames, and analyzes and monitors electrical load. The monitoring also includes detecting the vibrations of operating machinery in the factory area. The research proposes using ZigBee and Wi-Fi protocol intelligent monitoring system integration within the entire plant framework. The sensors on the factory site deliver messages and real-time sensing data to an integrated embedded systems via the ZigBee protocol. The integrated embedded system is built by the open-source 32-bit ARM (Advanced RISC Machine core Arduino Due module, where the network control codes are built in for the ARM chipset integrated controller. The intelligent integrated controller is able to instantly provide numerical analysis results according to the received data from the ZigBee sensors. The Android APP and web-based platform are used to show measurement results. The built-up system will transfer these results to a specified cloud device using the TCP/IP protocol. Finally, the Fast Fourier Transform (FFT approach is used to analyze the power loads in the factory zones. Moreover, Near Field Communication (NFC technology is used to carry out the actual electricity load experiments using smart phones.

  18. Space Experiment Module (SEM)

    Science.gov (United States)

    Brodell, Charles L.

    1999-01-01

    The Space Experiment Module (SEM) Program is an education initiative sponsored by the National Aeronautics and Space Administration (NASA) Shuttle Small Payloads Project. The program provides nationwide educational access to space for Kindergarten through University level students. The SEM program focuses on the science of zero-gravity and microgravity. Within the program, NASA provides small containers or "modules" for students to fly experiments on the Space Shuttle. The experiments are created, designed, built, and implemented by students with teacher and/or mentor guidance. Student experiment modules are flown in a "carrier" which resides in the cargo bay of the Space Shuttle. The carrier supplies power to, and the means to control and collect data from each experiment.

  19. A Mobile Sensor Network System for Monitoring of Unfriendly Environments.

    Science.gov (United States)

    Song, Guangming; Zhou, Yaoxin; Ding, Fei; Song, Aiguo

    2008-11-14

    Observing microclimate changes is one of the most popular applications of wireless sensor networks. However, some target environments are often too dangerous or inaccessible to humans or large robots and there are many challenges for deploying and maintaining wireless sensor networks in those unfriendly environments. This paper presents a mobile sensor network system for solving this problem. The system architecture, the mobile node design, the basic behaviors and advanced network capabilities have been investigated respectively. A wheel-based robotic node architecture is proposed here that can add controlled mobility to wireless sensor networks. A testbed including some prototype nodes has also been created for validating the basic functions of the proposed mobile sensor network system. Motion performance tests have been done to get the positioning errors and power consumption model of the mobile nodes. Results of the autonomous deployment experiment show that the mobile nodes can be distributed evenly into the previously unknown environments. It provides powerful support for network deployment and maintenance and can ensure that the sensor network will work properly in unfriendly environments.

  20. A Miniaturized Sensor for Microbial Monitoring of Spacecraft Water Environment, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Accurate real-time microbial monitoring of water environment is of paramount importance to crew health as well as to ensure proper functioning and control of the...

  1. Annual report on radioactive discharges and monitoring of the environment 1992. V. 1

    International Nuclear Information System (INIS)

    1993-01-01

    This Annual Report supplements and updates the Company's Environment Annual Report by providing more detailed information on radioactive discharges, monitoring of the environment and critical group doses. BNFL has published Annual Reports on Radioactive Discharges and Monitoring of the Environment since 1977. This year the report is again sub-divided into two complementary volumes. Volume I consists of site papers, one for each of the Company's sites and includes annual data on radioactive discharges into the environment and the associated environmental monitoring programmes. Critical group doses for each site are presented in summary tables at the beginning of each Site paper. Volume II reproduces the Certificates of Authorisation regulating the Company's discharges and the statutory environmental monitoring programmes which relate to them. (Author)

  2. Understanding the Spectrum Environment: Data and Monitoring to Improve Spectrum Utilization

    Data.gov (United States)

    Networking and Information Technology Research and Development, Executive Office of the President — The Wireless Spectrum Research and Development Senior Steering Group (WSRD SSG) Workshop V titled: Understanding the Spectrum Environment: Data and Monitoring to...

  3. An integrated environment monitoring system for underground coal mines--Wireless Sensor Network subsystem with multi-parameter monitoring.

    Science.gov (United States)

    Zhang, Yu; Yang, Wei; Han, Dongsheng; Kim, Young-Il

    2014-07-21

    Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs). We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS) as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between the WSN and the CMS. In order to implement the WSN for underground coal mines, two work modes are designed: periodic inspection and interrupt service; the relevant supporting technologies, such as routing mechanism, collision avoidance, data aggregation, interconnection with the CMS, etc., are proposed and analyzed. As WSN nodes are limited in energy supply, calculation and processing power, an integrated network management scheme is designed in four aspects, i.e., topology management, location management, energy management and fault management. Experiments were carried out both in a laboratory and in a real underground coal mine. The test results indicate that the proposed integrated environment monitoring system for underground coal mines is feasible and all designs performed well as expected.

  4. An Integrated Environment Monitoring System for Underground Coal Mines—Wireless Sensor Network Subsystem with Multi-Parameter Monitoring

    Science.gov (United States)

    Zhang, Yu; Yang, Wei; Han, Dongsheng; Kim, Young-Il

    2014-01-01

    Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs). We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS) as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between the WSN and the CMS. In order to implement the WSN for underground coal mines, two work modes are designed: periodic inspection and interrupt service; the relevant supporting technologies, such as routing mechanism, collision avoidance, data aggregation, interconnection with the CMS, etc., are proposed and analyzed. As WSN nodes are limited in energy supply, calculation and processing power, an integrated network management scheme is designed in four aspects, i.e., topology management, location management, energy management and fault management. Experiments were carried out both in a laboratory and in a real underground coal mine. The test results indicate that the proposed integrated environment monitoring system for underground coal mines is feasible and all designs performed well as expected. PMID:25051037

  5. An Integrated Environment Monitoring System for Underground Coal Mines—Wireless Sensor Network Subsystem with Multi-Parameter Monitoring

    Directory of Open Access Journals (Sweden)

    Yu Zhang

    2014-07-01

    Full Text Available Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs. We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between the WSN and the CMS. In order to implement the WSN for underground coal mines, two work modes are designed: periodic inspection and interrupt service; the relevant supporting technologies, such as routing mechanism, collision avoidance, data aggregation, interconnection with the CMS, etc., are proposed and analyzed. As WSN nodes are limited in energy supply, calculation and processing power, an integrated network management scheme is designed in four aspects, i.e., topology management, location management, energy management and fault management. Experiments were carried out both in a laboratory and in a real underground coal mine. The test results indicate that the proposed integrated environment monitoring system for underground coal mines is feasible and all designs performed well as expected.

  6. Distributed Monitoring and Resource Management for Large Cloud Environments

    OpenAIRE

    Wuhib, Fetahi Zebenigus

    2010-01-01

    Over the last decade, the number, size and complexity of large-scale networked systems has been growing fast, and this trend is expected to accelerate. The best known example of a large-scale networked system is probably the Internet, while large datacenters for cloud services are the most recent ones. In such environments, a key challenge is to develop scalable and adaptive technologies for management functions. This thesis addresses the challenge by engineering several protocols  for distri...

  7. Modular Sensor Environment : Audio Visual Industry Monitoring Applications

    OpenAIRE

    Guillot, Calvin

    2017-01-01

    This work was made for Electro Waves Oy. The company specializes in Audio-visual services and interactive systems. The purpose of this work is to design and implement a modular sensor environment for the company, which will be used for developing automated systems. This thesis begins with an introduction to sensor systems and their different topologies. It is followed by an introduction to the technologies used in this project. The system is divided in three parts. The client, tha...

  8. Pollution in the Gulf: Monitoring the marine environment

    International Nuclear Information System (INIS)

    Fowler, S.W.

    1993-01-01

    More than 2 years after the Gulf conflict, scientists are continuing to keep a close watch on marine pollution stemming from the war. Following the conflict in early 1991, major concern was raised worldwide when an estimated four to eight million barrels of crude oil were directly released into the Persian Gulf from the Sea Island terminal in Kuwait. Such amounts clearly made it the largest oil spill in history. The catastrophe was exacerbated when Kuwaiti oil fields were ignited. The magnitude of the pollution, and the types of toxic contaminants involved, led to a worldwide response through the United Nations system. An inter-agency plan of action was developed quickly. As one of its steps, the co-ordinating agency - the United Nations Environment Programme (UNEP) - asked the IAEA's Marine Environment Laboratory (MEL) in Monaco to help make a preliminary assessment of the situation. The Laboratory's main goal in initial surveys was to map the extent and general degree of the war-related pollution throughout the Gulf. Since the initial surveys were done, IAEA-MEL scientists have been engaged in regional follow-up activities in ongoing attempts to obtain a clearer picture of the oil pollution's effects on the Gulf's marine environment. This article highlights the laboratory's work in the Gulf following the 1991 conflict, within the context of co-operative programmes and projects. 1 fig

  9. O Cinema sem Imagens

    Directory of Open Access Journals (Sweden)

    Paulo Andrade

    2001-12-01

    Full Text Available A obra cinematográfica de Marguerite Duras, praticamente desconhecida pelo grande público, estabeleça intricadas relações com sua obra literária, ao promover a indiscernibilidade entre os dois campo, sem, contudo, instituir qualquer tipo de subordinação de um ao outro. O processo de criação do filme Lê camion, de 1977, aponta para outras possibilidades de se pensar o cinema e a literatura.

  10. Monitoring Interior and Exterior Wall Inspections within a Virtual Environment

    Directory of Open Access Journals (Sweden)

    A. Z. Sampaio

    2012-01-01

    Full Text Available This paper describes two prototype applications based on the Virtual Reality (VR technology for use in maintenance planning of buildings. In a building, the paint coating applied to interior walls and the different types of materials applied to façades convey their aesthetic character and also perform an important function of protection. This a construction component which is exposed to agents of deterioration related to its use, needing the regular evaluation of its state of repair. The applications support the performance of such periodic inspections and the monitoring of interior and exterior wall maintenance, using the VR technology. Used during an inspection visit, the applications allow users to consult a database of irregularities, normally associated with the coating, classified by the most probable causes and by the recommended repair methodologies. In addition, a chromatic scale related to the degree of deterioration of the coating, defined as a function of the time between the dates of the application of the paint and the scheduled repainting, can be attributed to each element of coating monitored. This use of the VR technology allows inspections and the evaluation of the degree of wear and tear of materials to be carried out in a highly direct and intuitive manner.

  11. Democracy in the Digital Communication Environment: A Typology Proposal of Political Monitoring Processes

    OpenAIRE

    Feenstra, Ramón A.; Casero Ripollés, Andreu

    2014-01-01

    The digital environment creates new opportunities for citizen political participation. Among these, the monitoring of political and economic power centers stands out. This includes public scrutiny of the management of public funds and the activities of the public and economic systems, thus denouncing dysfunctional features. This article aims to describe, differentiate, and classify the various forms that monitoring can take in current democracies. The results indicate that three major monitor...

  12. Lidar Remote Sensing for Industry and Environment Monitoring

    Science.gov (United States)

    Singh, Upendra N. (Editor); Itabe, Toshikazu (Editor); Sugimoto, Nobuo (Editor)

    2000-01-01

    Contents include the following: 1. Keynote paper: Overview of lidar technology for industrial and environmental monitoring in Japan. 2. lidar technology I: NASA's future active remote sensing mission for earth science. Geometrical detector consideration s in laser sensing application (invited paper). 3. Lidar technology II: High-power femtosecond light strings as novel atmospheric probes (invited paper). Design of a compact high-sensitivity aerosol profiling lidar. 4. Lasers for lidars: High-energy 2 microns laser for multiple lidar applications. New submount requirement of conductively cooled laser diodes for lidar applications. 5. Tropospheric aerosols and clouds I: Lidar monitoring of clouds and aerosols at the facility for atmospheric remote sensing (invited paper). Measurement of asian dust by using multiwavelength lidar. Global monitoring of clouds and aerosols using a network of micropulse lidar systems. 6. Troposphere aerosols and clouds II: Scanning lidar measurements of marine aerosol fields at a coastal site in Hawaii. 7. Tropospheric aerosols and clouds III: Formation of ice cloud from asian dust particles in the upper troposphere. Atmospheric boundary layer observation by ground-based lidar at KMITL, Thailand (13 deg N, 100 deg. E). 8. Boundary layer, urban pollution: Studies of the spatial correlation between urban aerosols and local traffic congestion using a slant angle scanning on the research vessel Mirai. 9. Middle atmosphere: Lidar-observed arctic PSC's over Svalbard (invited paper). Sodium temperature lidar measurements of the mesopause region over Syowa Station. 10. Differential absorption lidar (dIAL) and DOAS: Airborne UV DIAL measurements of ozone and aerosols (invited paper). Measurement of water vapor, surface ozone, and ethylene using differential absorption lidar. 12. Space lidar I: Lightweight lidar telescopes for space applications (invited paper). Coherent lidar development for Doppler wind measurement from the International Space

  13. Radioecological monitoring of the environment in the Republic of Moldova

    International Nuclear Information System (INIS)

    Coretchi, Liubov; Cornescu, A.; Coretchi, Lilia; Chiruta, Iu.

    2009-01-01

    Fundamental criteria of radiation protection, which are required today as a result of various practical applications of nuclear energy, obliges us to carefully analyze environmental issues as a result of the presence of radioactive isotopes into the environment. This is due to the fact that the study of correlated environmental contamination and transmission vectors of radionuclide to humans is a primary means to protect public health. Basic principles that should be considered within the meaning of those already mentioned the processes of knowledge transfer and concentration of radionuclide in the ecosystems in the study taken in medicinal plants, construction materials, food and drinking water. The results regarding quantification of natural and artificial radionuclide activity into environmental factors, food products and construction material are presented in this paper. It was demonstrated that the activity of investigated radionuclide do not essentially exceeded the maximal admissible values indicated in Fundamental Norms of Radiation protection. (authors)

  14. Bioindicators for monitoring radioactive pollution of the marine environment

    International Nuclear Information System (INIS)

    Dahlgaard, H.

    1981-05-01

    Mussels (Mytilus edulis) are globally used as bioindicators for pollution of coastal and estuarine environments by metals and radionuclides. The aim of this work has been to improve the use of Mytilus edulis as a bioindicator by gaining knowledge on its accumulation and loss of certain radionuclides ( 65 Zn, 57 Co, 54 Mn, 51 Cr, 59 Fe and 134 Cs) under different fieldcomparable environmental conditions. A laboratory set-up in which natural concentrations of suspended phytoplankton are kept constant for weeks was evolved for the accumulation experiments with mussels. It is argued that continuous feeding at very low (natural) levels is necessary if field-comparable experiments are to be performed with suspension feeding bivalves. Accumulation via food intake was studied by comparing experiments with different concentrations of contaminated phytoplankton (Phaeodactylum tricornutum). This comparison showed no effect of varying the phytoplankton concentration. Decreasing the salinity and increasing the temperature elevated the influx (initial rate of accumulation) of the radionuclides. During one year excretion experiments were performed by weekly wholebody countings of laboratory contaminated mussels which had been re-introduced in their natural environment. A seasonal effect on the biological half life was detected for 65 Zn. It is concluded that mussels are useful bioindicators provided the variability due to environmental factors, e.g. season and salinity, is taken into consideration. Brown algae, expecially Fucus vesiculosus, were used to trace the controlled liquid discharges (mainly 60 Co, 58 Co, 65 Zn, 54 Mn and sup(110m)Ag) from two Swedish nuclear power plants (Barsebaeck and Ringhals)> Fucus showed higher accumulation than Mytilus. Transfer factors between discharge and sample from a specified location are presented. It is argued that these transfer factors may be useful in estimating the magnitude of an uncontrolled accidental release of activity and its

  15. Space environment monitoring by low-altitude operational satellites

    International Nuclear Information System (INIS)

    Kroehl, H.W.

    1982-01-01

    The primary task of the Defense Meteorological Satellite Program (DMSP) is the acquisition of meteorological data in the visual and infrared spectral regions. The Air Weather Service operates two satellites in low-altitude, sun-synchronous, polar orbits at 850 km altitude, 98.7 deg inclination, 101.5 minute period and dawn-dusk or noon-midnight equatorial crossing times. Special DMSP sensors of interest to the space science community are the precipitating electron spectrometer, the terrestrial noise receiver, and the topside ionosphere plasma monitor. Data from low-altitude, meteorological satellites can be used to build empirical models of precipitating electron characteristics of the auroral zone and polar cap. The Tiros-NOAA satellite program complements the DMSP program. The orbital elements are the same as DMSP's, except for the times of equatorial crossing, and the tilt of the orbital plane. The Tiros-NOAA program meets the civilian community's needs for meteorological data as the DMSP program does for the military

  16. Hanford, Washington: Monitoring to assess the state of the environment

    International Nuclear Information System (INIS)

    Gray, R.H.

    1992-01-01

    Environmental monitoring has been ongoing at the US Department of Energy's Hanford Site for almost 5 years. Concentrations of airborne radionuclides at the Site perimeter, and concentrations of radionuclides and nonradiological water quality in the Columbia River are in compliance with applicable standards. Radionuclide levels in food stuffs irrigated with river water taken downstream of the Site, most onsite wildlife samples, and soils and vegetation from both on- and off-site locations are typical of those attributable to worldwide fallout. The calculated dose potentially received by a maximally exposed individual, using worst-case assumptions for all routes of exposure, was 0.05 mrem/yr in 1989. The average per capita whole-body effective dose to people, based on a population of 340,000 living within 80 km (50 mi) of the Site, was <0.01 to 0.03 mrem annually from 1985 through 1989. Chinook salmon (Oncorhynchus tshawytscha) spawning in Hanford Reach of the Columbia River has increased in recent years with a con-comitant increase in winter roosting activity of bald eagles (Haliaeetus leucocephalus). An elk (Cervus elaphus) herd, established by immigration in 1972, is also increasing. Nesting Canada goose (Branta canadensis), great blue heron (Ardea herodias), various plants and other animals, e.g., mule deer (Odocoileus hemionus), and coyotes (Canis latrans) are common

  17. Tools for monitoring aquatic environments to identify anthropic effects.

    Science.gov (United States)

    da Rocha, Monyque Palagano; Dourado, Priscila Leocadia Rosa; Cardoso, Claudia Andrea Lima; Cândido, Liliam Silva; Pereira, Joelson Gonçalves; de Oliveira, Kelly Mari Pires; Grisolia, Alexeia Barufatti

    2018-01-05

    Anthropic activities are directly related to the contamination of aquatic ecosystems owing to the release of numerous chemicals from agricultural and urban waste. These contaminants cause environmental degradation and a decrease in the availability of water quality. The objective of this search was to evaluate the efficiency of physicochemical, chemical, and microbiological tests; extraction of chlorophyll a; and genetic parameters to identify anthropic activities and weather condition effects on the stream water quality and the consequences of its use by the population. The physicochemical parameters were within the limits allowed by the Brazilian law. However, contamination by metals (Cd 0.510 mg L -1 , Co 0.405 mg L -1 , and Ni 0.316 mg L -1 ) has been found at various collection points to be more than the allowable values. The antibiotic oxytetracycline was detected in stream water in quantities of up to 89 μg L -1 . In relation to microbiological contamination, Escherichia coli and Pseudomonas spp. have been isolated. The averages of chlorophyll a were up to 0.15558 mg cm -2 . Genetic tools identified greater number of micronuclei and DNA damage in periods that showed lower rainfall rates and lower amounts of metals. The analysis used for monitoring was efficient to verify the interference that animal breeding and planting of different cultures have caused on that stream. Thus, the continued use of this water for drinking, irrigation of vegetables, and recreational activities makes the population susceptible to contamination by bacteria and creates conditions for the development of genetic alterations in the long run.

  18. Toward an optimisation technique for dynamically monitored environment

    Science.gov (United States)

    Shurrab, Orabi M.

    2016-10-01

    The data fusion community has introduced multiple procedures of situational assessments; this is to facilitate timely responses to emerging situations. More directly, the process refinement of the Joint Directors of Laboratories (JDL) is a meta-process to assess and improve the data fusion task during real-time operation. In other wording, it is an optimisation technique to verify the overall data fusion performance, and enhance it toward the top goals of the decision-making resources. This paper discusses the theoretical concept of prioritisation. Where the analysts team is required to keep an up to date with the dynamically changing environment, concerning different domains such as air, sea, land, space and cyberspace. Furthermore, it demonstrates an illustration example of how various tracking activities are ranked, simultaneously into a predetermined order. Specifically, it presents a modelling scheme for a case study based scenario, where the real-time system is reporting different classes of prioritised events. Followed by a performance metrics for evaluating the prioritisation process of situational awareness (SWA) domain. The proposed performance metrics has been designed and evaluated using an analytical approach. The modelling scheme represents the situational awareness system outputs mathematically, in the form of a list of activities. Such methods allowed the evaluation process to conduct a rigorous analysis of the prioritisation process, despite any constrained related to a domain-specific configuration. After conducted three levels of assessments over three separates scenario, The Prioritisation Capability Score (PCS) has provided an appropriate scoring scheme for different ranking instances, Indeed, from the data fusion perspectives, the proposed metric has assessed real-time system performance adequately, and it is capable of conducting a verification process, to direct the operator's attention to any issue, concerning the prioritisation capability

  19. Radioactivity in the environment. A summary and radiological assessment of the Environment Agency's monitoring programmes; report for 1997

    International Nuclear Information System (INIS)

    1997-01-01

    The Radioactive Substances Act 1993 provides for controls to be exercised over the keeping and use of radioactive materials and, in particular, on the accumulation and disposal of radioactive wastes. The Environment Agency is responsible for administration and enforcement of the Act in England and Wales. In support of these regulatory functions and as part of the UK Government's arrangements for providing information to the European Commission under the Euratom Treaty, the Agency commissions independent monitoring of radioactive waste disposals and their impact on the environment, and monitoring of radioactivity in air, rainwater and drinking water sources. This report presents the data from these monitoring programmes and provides a commentary on their radiological significance. It includes assessments of radiation exposure of members of the public for compliance with the annual dose limit recommended by the International Commission on Radiological Protection. Concentrations of radioactivity in water are also assessed in relation to the guidelines on drinking water quality recommended by the World Health Organisation. This report for 1997 is one of an annual series published by the Agency. It is being distributed to local authorities as part of the arrangements under the Radioactive Substances Act 1993 for provision of access to environmental information. The monitoring programmes and preparation of this report are managed by the Agency's National Compliance Assessment Service. (author)

  20. Radioactivity in the environment. A summary and radiological assessment of the Environment Ageny's monitoring programmes. Report for 1996

    International Nuclear Information System (INIS)

    1996-01-01

    This report presents the results from the Environment Agency's monitoring of radioactivity in the environment during 1996. Monitoring programmes were carried out in support of the Agency's regulatory functions under the Radioactive Substances Act 1993 and as part of the UK Government's obligations under the Euratom Treaty. The programmes included: effluent monitoring; the quality checking of solid waste disposals; environmental monitoring; the monitoring of radioactivity in air and rainwater; the monitoring of radioactivity in drinking water sources. A total of 160 effluent samples were analysed for nearly 900 determinants, two consignments of solid radioactive waste destined for disposal at British Nuclear Fuels' site at Drigg were checked, direct instrumental monitoring was carried out at ISO locations within the vicinity of nuclear sites, and 532 environmental samples were analysed for over 2,000 determinants. Effluent monitoring: The Agency requires operators of certain sites to provide samples of their liquid effluents for independent analysis. The results are compared with reports submitted by site operators. The majority of results showed satisfactory agreement; operators' values were frequently higher than the Agency's measurements indicating that they were not under-reporting. However, some discrepancies were found and are being investigated. Quality checking of solid waste disposals: Consignments of solid low level radioactive waste are seized by inspectors for examination at the Agency's Waste Quality Checking Laboratory. Sophisticated non-destructive and destructive analytical techniques are used at the laboratory to check the radioactive content and description of the wastes. Consignments of waste from the Atomic Weapons Establishment at Aldermaston and Amersham International at Amersham were examined. In both cases the operators reported higher activity than the Agency's laboratory. The consignments also conformed with the operators' disposal

  1. SEM analysis for irradiated materials

    International Nuclear Information System (INIS)

    Liu Xiaosong; Yao Liang

    2008-06-01

    A radiation-proof Scanning Electron Microscope (SEM) system is introduced. It has been widely used in various areas. For analyzing radioactive samples, normal SEM system needs lots of alterations. Based on KYKY-2800B SEM, the sample room, belt line, operating table and aerator were updated. New radiation-proof SEM system has used to analytic surface contaminated samples and RPV materials samples. An elementary means of SEM analysis for radioactive samples was studied, and this examination supported some available references for further irradiated fuel researches. (authors)

  2. A novel vision-based mold monitoring system in an environment of intense vibration

    International Nuclear Information System (INIS)

    Hu, Fen; He, Zaixing; Zhao, Xinyue; Zhang, Shuyou

    2017-01-01

    Mold monitoring has been more and more widely used in the modern manufacturing industry, especially when based on machine vision, but these systems cannot meet the detection speed and accuracy requirements for mold monitoring because they must operate in environments that exhibit intense vibration during production. To ensure that the system runs accurately and efficiently, we propose a new descriptor that combines the geometric relationship-based global context feature and the local scale-invariant feature transform for the image registration step of the mold monitoring system. The experimental results of four types of molds showed that the detection accuracy of the mold monitoring system is improved in the environment with intense vibration. (paper)

  3. A novel vision-based mold monitoring system in an environment of intense vibration

    Science.gov (United States)

    Hu, Fen; He, Zaixing; Zhao, Xinyue; Zhang, Shuyou

    2017-10-01

    Mold monitoring has been more and more widely used in the modern manufacturing industry, especially when based on machine vision, but these systems cannot meet the detection speed and accuracy requirements for mold monitoring because they must operate in environments that exhibit intense vibration during production. To ensure that the system runs accurately and efficiently, we propose a new descriptor that combines the geometric relationship-based global context feature and the local scale-invariant feature transform for the image registration step of the mold monitoring system. The experimental results of four types of molds showed that the detection accuracy of the mold monitoring system is improved in the environment with intense vibration.

  4. Radiation Protection of the Public and the Environment. Overcoming Environmental Monitoring Inertia

    International Nuclear Information System (INIS)

    Parker, T.G.; Desmond, J.A.; Stevens, A.K.

    2006-01-01

    The first nuclear reactors at Sellafield went critical in 1951 and fuel reprocessing commenced shortly afterwards. As the nuclear programme expanded, reprocessing increased and there was an associated increase in discharges to the environment. An initial environmental monitoring programme was formulated on the basis of research and assessment of the likely behaviour of radionuclides. In addition to the routine process sources there were also incidents that gave rise to acute releases of radioactivity to the environment. Of key significance were: the Windscale fire, 1957; short-cooled fuel reprocessing, 1981; and discharge of contaminated solvent, 1983. All of these incidents added to the requirements for environments for environmental monitoring. The monitoring programme has evolved over a period of more than 50 years. (N.C.)

  5. Radiation Protection of the Public and the Environment. Overcoming Environmental Monitoring Inertia

    Energy Technology Data Exchange (ETDEWEB)

    Parker, T.G.; Desmond, J.A. [British Nuclear Group Sellafield Ltd. (United Kingdom); Stevens, A.K. [Westlakes Scientific Consulting (United Kingdom)

    2006-07-01

    The first nuclear reactors at Sellafield went critical in 1951 and fuel reprocessing commenced shortly afterwards. As the nuclear programme expanded, reprocessing increased and there was an associated increase in discharges to the environment. An initial environmental monitoring programme was formulated on the basis of research and assessment of the likely behaviour of radionuclides. In addition to the routine process sources there were also incidents that gave rise to acute releases of radioactivity to the environment. Of key significance were: the Windscale fire, 1957; short-cooled fuel reprocessing, 1981; and discharge of contaminated solvent, 1983. All of these incidents added to the requirements for environments for environmental monitoring. The monitoring programme has evolved over a period of more than 50 years. (N.C.)

  6. Final annual report of the Partial monitoring system 'Radioactivity of the environment' 2015

    International Nuclear Information System (INIS)

    Melicherova, T.; Cabanekova, H.; Bodorova, J.

    2016-05-01

    The present report evaluates activities of radiation monitoring of Slovak Hydrometeorological Institute (SHMI) in 2015. Analytical part focuses on detailed statistical analysis of monitored data. Detailed knowledge of the course of time series during uneventful period enables early detect and analyze potential increase of radioactivity levels in the environment originating from domestic or foreign sources. SHMI is responsible for international data exchange with the European Commission and with partners in Austria and Hungary.

  7. Final annual report of the Partial monitoring system 'Radioactivity of the environment' 2016

    International Nuclear Information System (INIS)

    Melicherova, T.; Cabanekova, H.; Bodorova, J.

    2017-05-01

    The present report evaluates activities of radiation monitoring of Slovak Hydrometeorological Institute (SHMI) in 2016. Analytical part focuses on detailed statistical analysis of monitored data. Detailed knowledge of the course of time series during uneventful period enables early detect and analyze potential increase of radioactivity levels in the environment originating from domestic or foreign sources. SHMI is responsible for international data exchange with the European Commission and with partners in Austria and Hungary.

  8. Annual report on radioactive discharges and monitoring of the environment, 1996. V. 1

    International Nuclear Information System (INIS)

    1997-01-01

    British Nuclear Fuels Limited (BNFL)'s 1996 report on radioactive discharges from its various sites and monitoring of the surrounding environments are described. For each of the Sellafield, Drigg, Chapelcross, Springfields and Capenhurst sites, details are given on normal operations, radioactive discharges in gaseous, liquid or solid forms, environmental monitoring routines and collective dose and critical group estimates. The second, linked, volume of this report covers certificates of authorisation issued to the company. (UK)

  9. The Integrated Design for Micro - environment Monitoring System of Showcase in Museum

    Directory of Open Access Journals (Sweden)

    Dong Chan

    2017-01-01

    Full Text Available In order to improve the current environment quality of cultural relics in museum and make them preserved for a long time, the paper proposes the integrated design for micro - environment monitoring system of showcase in museum, the system mainly monitors the micro-environment of heritage, such as ultraviolet, light, formaldehyde, CO2, TVOC, PM 2.5, choosing cotex-M3 ARM microcontroller STM32F103ZET6 as the control core. Based on the concept of integration, the system integrates the single air monitoring instruments. The design of circuit mainly includes the process of digital power supply and analog power supply, the acquisition and processing of 5 analog signals from sensors, and the design of reserved interface. In the aspect of interaction, the serial port lcd module was uesd for the display and control, which can get rid of the control of PC and achieve the functions of environmental monitoring, environmental warning, environmental assessment, historical data query. The integrated design for Micro-environment of Showcase in Museum achieves a monitoring platform successfully which is easy for users’ operation and access to display information conveniently. The advantages of the system are strong portability, low cost and short development cycle.

  10. The application of entropy weight TOPSIS method to optimal points in monitoring the Xinjiang radiation environment

    International Nuclear Information System (INIS)

    Feng Guangwen; Hu Youhua; Liu Qian

    2009-01-01

    In this paper, the application of the entropy weight TOPSIS method to optimal layout points in monitoring the Xinjiang radiation environment has been indroduced. With the help of SAS software, It has been found that the method is more ideal and feasible. The method can provide a reference for us to monitor radiation environment in the same regions further. As the method could bring great convenience and greatly reduce the inspecting work, it is very simple, flexible and effective for a comprehensive evaluation. (authors)

  11. NOVANA - National Monitoring and Assessment Programme for the Aquatic and Terrestrial Environment

    DEFF Research Database (Denmark)

    Svendsen, L. M.

    This report is Part 1 of the Programme Description of NOVANA - the Nationwide Monitoring and Assessment Programme for the Aquatic and Terrestrial Environments. Part 1 comprises a general description of the background for the programme, including the international obliga-tions and requirements...... for monitoring of nature and the environment. The overall objective and the scientific and strategic background for the priorities upon which NOVANA pro-gramme is based are described, as are the organization of the programme, the overall economy and the technical assumptions made. Finally the scientific content...

  12. ENVIRONMENT PROTECTION AND ENVIRONMENT MONITORING ISSUES IN THE PROJECTS OF SUBGLACIAL LAKES STUDIES IN ANTARCTICA

    Directory of Open Access Journals (Sweden)

    I. A. Alekhina

    2012-01-01

    Full Text Available Antarctic subglacial lakes can represent extreme natural habitats for microorganisms from the position of their evolution and adaptation, as well as they can contain the information on Antarctic ice sheet history and climatic changes in their sediments. Now only direct measurements and sampling from these habitats can answer on many fundamental questions. Special precaution should be complied at penetration into these unique relic environments without unfavorable impacts and contamination. A number of recommendations were developed on levels of cleanliness and sterility during direct exploration and research of subglacial environments. Documents considered in the article are the first and necessary steps for appropriate and long-term ecological management of subglacial Antarctic environments. Today there are three projects of subglacial aquatic environment research which are in preparation and realization – the Russian project of Lake Vostok, the similar British project of Lake Ellsworth and the American project on Whillans Ice Stream. The programs of ecological stewardship for direct exploration of these lakes are discussed. All these subglacial aquatic objects of further exploration and research are so various on their structure, age and regime, that only results of all programs as a whole can help to draw us a uniform picture of a subglacial ecological system. Ecological stewardship of these should provide the minimal ecological impact with maximal scientific results. On the basis of existing documents and recommendations the general approaches and the program of ecological stewardship for Lake Vostok research are discussed. Study of drilling fluid, drilling chips, Vostok ice core and the fresh frozen water will allow to make an assessment of biological and chemical contamination as a result of the first penetration and to modify the further stewardship program for the second penetration and direct exploration of lake water.

  13. Radiation protection instrumentation. Monitoring equipment. Atmospheric radioactive iodine in the environment

    International Nuclear Information System (INIS)

    1995-01-01

    This international standard applies to portable or installed equipment for the monitoring of radioactive iodine (such as I-131 or I-125) in air in the environment of nuclear installations during normal operation, during design basis events, and in emergency situations. The monitoring involves continuous sample trapping and, where adequate, automatic start of sampling. The document deals with radioactive iodine monitor design, testing procedures, and documentation. Appended tables refer to the reference and normal testing conditions, tests in normal testing conditions, tests during changes of the affecting quantities, and tests of changes in the air circuit. (P.A.)

  14. Annual report on radioactive discharges and monitoring of the environment 1991. V. 2

    International Nuclear Information System (INIS)

    1992-01-01

    This Annual Report supplements British Nuclear Fuel plc's Health and Safety Annual Report by providing more detailed information on radioactive discharges, monitoring of the environmental and critical group doses. BNFL has published Annual Reports on Radioactive Discharges and Monitoring of the Environment, covering the period from 1977 to the present. For 1991 this report has been sub-divided into two complementary parts. Volume II reproduces the Certificates of Authorisation under which the Company operates and the statutory environmental monitoring programmes which relate to them. (author)

  15. Annual report on radioactive discharges and monitoring of the environment 1992. V. 2

    International Nuclear Information System (INIS)

    1993-01-01

    This Annual Report supplements British Nuclear Fuel plc's Health and Safety Annual Report by providing more detailed information on radioactive discharges, monitoring of the environmental and critical group doses. BNFL has published Annual Reports on Radioactive Discharges and Monitoring of the Environment, covering the period from 1977 to the present. For 1991 this report has been sub-divided into two complementary parts. Volume II reproduces the Certificates of Authorisation under which the Company operates and the statutory environmental monitoring programmes which relate to them. (author)

  16. Review of passive accumulation devices for monitoring organic micropollutants in the aquatic environment.

    Science.gov (United States)

    Stuer-Lauridsen, Frank

    2005-08-01

    Over the past 15 years passive sampling devices have been developed that accumulate organic micropollutants and allow detection at ambient sub ng/l concentrations. Most passive accumulation devices (PADs) are designed for 1-4 weeks field deployment, where uptake is governed by linear first order kinetics providing a time weighted average of the exposure concentration. Semipermeable membrane devices (SPMDs) are the most comprehensively studied PADs, but other samplers may also be considered for aquatic monitoring purposes. The applicability of the PADs is reviewed with respect to commonly monitored aqueous matrices and compounds, the detection limits, and for use in quantitative monitoring related to requirements embedded in the EU Water Framework Directive, the US and EU Water Quality Criteria, and the Danish monitoring aquatic programme. The PADs may monitor >75% of the organic micropollutants of the programmes. Research is warranted regarding the uptake in PADs in low flow environments and for the development of samplers for polar organic compounds.

  17. Advanced metrology by offline SEM data processing

    Science.gov (United States)

    Lakcher, Amine; Schneider, Loïc.; Le-Gratiet, Bertrand; Ducoté, Julien; Farys, Vincent; Besacier, Maxime

    2017-06-01

    Today's technology nodes contain more and more complex designs bringing increasing challenges to chip manufacturing process steps. It is necessary to have an efficient metrology to assess process variability of these complex patterns and thus extract relevant data to generate process aware design rules and to improve OPC models. Today process variability is mostly addressed through the analysis of in-line monitoring features which are often designed to support robust measurements and as a consequence are not always very representative of critical design rules. CD-SEM is the main CD metrology technique used in chip manufacturing process but it is challenged when it comes to measure metrics like tip to tip, tip to line, areas or necking in high quantity and with robustness. CD-SEM images contain a lot of information that is not always used in metrology. Suppliers have provided tools that allow engineers to extract the SEM contours of their features and to convert them into a GDS. Contours can be seen as the signature of the shape as it contains all the dimensional data. Thus the methodology is to use the CD-SEM to take high quality images then generate SEM contours and create a data base out of them. Contours are used to feed an offline metrology tool that will process them to extract different metrics. It was shown in two previous papers that it is possible to perform complex measurements on hotspots at different process steps (lithography, etch, copper CMP) by using SEM contours with an in-house offline metrology tool. In the current paper, the methodology presented previously will be expanded to improve its robustness and combined with the use of phylogeny to classify the SEM images according to their geometrical proximities.

  18. Sistema embarcado para monitoramento sem fio de sinais em soldagem a arco elétrico com abordagem tecnológica Embedded system for wireless signal monitoring during arc welding with technological approach

    Directory of Open Access Journals (Sweden)

    Marcus Vinícius Ribeiro Machado

    2012-06-01

    Full Text Available Industrialmente, o processo de soldagem a arco é o mais importante na produção e reparo de equipamentos, e sendo um processo especial de fabricação, que não pode ser completamente inspecionado contra imperfeições somente após sua finalização, o monitoramento da produção se faz necessário. Este monitoramento é tecnologicamente requerido pelas normas ISO 3834:2005 e ISO 17662:2005, que dizem que o fabricante deve adotar medidas para garantir a qualidade necessária, além de especificarem os dados que devem ser monitorados e a correta calibração dos sistemas e equipamentos de medida. Este, portanto, pode ser usado para garantir documentação do processo e tomadas de ações corretivas. Existem sistemas que realizam o monitoramento satisfatoriamente, mas o uso de comunicação por cabos e/ou com computador dedicado dificultam suas aplicações industriais. Então, um sistema embarcado, independente, que monitore diferentes sinais do processo de soldagem e que se comunique de forma robusta e flexível a diferentes equipamentos é fundamental para a indústria. Este sistema deve ser de utilização simplificada e apresentar o estado da arte em tecnologia de comunicação. Devido a essa necessidade, foi então projetado e construído um sistema para monitoramento sem fio de sinais em soldagem a arco elétrico, denominado de MoSo Wi-Fi. Três canais de aquisição estão disponíveis (tensão, corrente e velocidade de alimentação de arame, sendo validados pela instrumentação de soldagens TIG CA e MIG/MAG (curto-circuito, goticular e pulsado, demonstrando grande aplicabilidade e robustez a um baixo custo de hardware.Industrially, arc welding process is the most important in equipment production and repair, and being a special manufacturing process, which cannot be completely inspected for flaws only after its completion, production monitoring is necessary. This monitoring is technologically required by ISO 3834:2005 and ISO 17662

  19. Monitoring of radiation in the environment in the Netherlands. Results in 2001

    CERN Document Server

    Knetsch, G J

    2002-01-01

    This report presents the results of radioactivity measurements in the Dutch environment in 2001. The measurements were carried out by RIVM, RIZA, RIKZ and Inspectorate for Health Protection and Veterinary Public Health. Radioactivity measurements were carried out on airborne particles, deposition, surface water, seawater, drinking water and food (honey, powdered milk, game, poultry, blueberry and chanterelle). Results for ambient dose equivalent rates were obtained from the National Radioactivity Monitoring Network. The levels of radioactivity in the Dutch environment were not elevated in 2001

  20. Monitoring of radiation in the environment in the Netherlands. Results in 2001

    Energy Technology Data Exchange (ETDEWEB)

    Knetsch, G.J. (ed.)

    2002-07-01

    This report presents the results of radioactivity measurements in the Dutch environment in 2001. The measurements were carried out by RIVM, RIZA, RIKZ and Inspectorate for Health Protection and Veterinary Public Health. Radioactivity measurements were carried out on airborne particles, deposition, surface water, seawater, drinking water and food (honey, powdered milk, game, poultry, blueberry and chanterelle). Results for ambient dose equivalent rates were obtained from the National Radioactivity Monitoring Network. The levels of radioactivity in the Dutch environment were not elevated in 2001.

  1. Environs monitoring

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    There were no releases of gaseous waste from ORNL which were of a level that required an incident report to the ERDA. The average concentration of beta radioactivity in the atmosphere at the perimeter of the ERDA-controlled area was less than one percent of the value appliable to releases to uncontrolled areas. There were no releases of liquid waste from the Laboratory which were of a level that required an incident report to the ERDA. The quantity of radionuclides of primary concern in the Clinch River averaged less than 0.4 percent of the MPC/sub w/. The average background level at the PAM and RAM stations during 1974 was 7.5 μR/hr, or 0.3 μR/hr less than the average for 1973. Nine soil samples were collected and analyzed for plutonium and uranium. Plutonium content ranged from 0.9 x 10 -8 μCi/g to 3.4 x 10 -8 μCi/g, and the uranium content ranged from 43 x 10 -8 /g to 117 x 10 -8 μCi/g. (auth)

  2. Monitoring aquatic environment pollution : a major component of environment management system part-II

    International Nuclear Information System (INIS)

    Khan, I.H.; Khan, M.H.; Sheikh, I.M.

    1999-01-01

    The quality of water suitable for simple disinfection and filtration is presented in this article. Aquatic monitoring requires sampling frequencies along the alignment of surface water bodies. It is necessary to control the industrial effluents discharge in to river and sewers. Unlike wastes from entirely domestic sources, however industrial effluents may contain a very large variety of unnatural components which necessitates greater considerations in setting suitable discharge limits and, perhaps closer surveillance to ensure that standards are met. Several suggestion and example of different types of effluent have been described. All the examples given are sufficiently convincing that Pakistan can learn a great deal from international experiences in environmental pollution to avoid catastrophes. (A.B.)

  3. Food and beverage environment analysis and monitoring system: a reliability study in the school food and beverage environment.

    Science.gov (United States)

    Bullock, Sally Lawrence; Craypo, Lisa; Clark, Sarah E; Barry, Jason; Samuels, Sarah E

    2010-07-01

    States and school districts around the country are developing policies that set nutrition standards for competitive foods and beverages sold outside of the US Department of Agriculture's reimbursable school lunch program. However, few tools exist for monitoring the implementation of these new policies. The objective of this research was to develop a computerized assessment tool, the Food and Beverage Environment Analysis and Monitoring System (FoodBEAMS), to collect data on the competitive school food environment and to test the inter-rater reliability of the tool among research and nonresearch professionals. FoodBEAMS was used to collect data in spring 2007 on the competitive foods and beverages sold in 21 California high schools. Adherence of the foods and beverages to California's competitive food and beverage nutrition policies for schools (Senate Bills 12 and 965) was determined using the data collected by both research and nonresearch professionals. The inter-rater reliability between the data collectors was assessed using the intraclass correlation coefficient. Researcher vs researcher and researcher vs nonresearcher inter-rater reliability was high for both foods and beverages, with intraclass correlation coefficients ranging from .972 to .987. Results of this study provide evidence that FoodBEAMS is a promising tool for assessing and monitoring adherence to nutrition standards for competitive foods sold on school campuses and can be used reliably by both research and nonresearch professionals. Copyright 2010 American Dietetic Association. Published by Elsevier Inc. All rights reserved.

  4. Oxford CyberSEM: remote microscopy

    International Nuclear Information System (INIS)

    Rahman, M; Kirkland, A; Cockayne, D; Meyer, R

    2008-01-01

    The Internet has enabled researchers to communicate over vast geographical distances, sharing ideas and documents. e-Science, underpinned by Grid and Web Services, has enabled electronic communications to the next level where, in addition to document sharing, researchers can increasingly control high precision scientific instruments over the network. The Oxford CyberSEM project developed a simple Java applet via which samples placed in a JEOL 5510LV Scanning Electron Microscope (SEM) can be manipulated and examined collaboratively over the Internet. Designed with schoolchildren in mind, CyberSEM does not require any additional hardware or software other than a generic Java-enabled web browser. This paper reflects on both the technical and social challenges in designing real-time systems for controlling scientific equipments in collaborative environments. Furthermore, it proposes potential deployment beyond the classroom setting.

  5. The Ocean State Report of the Copernicus Marine Environment Monitoring Service

    Science.gov (United States)

    von Schuckmann, Karina

    2017-04-01

    COPERNICUS is the European Earth observation and monitoring programme, which aims to give the European Union autonomous and operational capability in space-based observation facilities (see the Sentinel missions) and in situ (measurements in the atmosphere, in the ocean and on the ground), and to operate six interlinked environmental monitoring services for the oceans, the atmosphere, territorial development, emergency situations, security and climate change. In this context, the Copernicus Marine Environment Monitoring Service provides an open and free access to regular and systematic information about the physical state and dynamics of the ocean and marine ecosystems for the global ocean and six European regional seas. Mercator Ocean, the French center of global ocean analysis and forecast has been entrusted by the EU to implement and operate the Copernicus Marine Service. The first Ocean State Report Copernicus Marine Environment Monitoring Service has been prepared, and is planned to appear at an annual basis (fall each year) as a unique reference for ocean state reporting. This report contains a state-of-the-art value-added synthesis of the ocean state for the global ocean and the European regional seas from the Copernicus Marine Environment Monitoring Service data products and expert analysis. This activity is aiming to reach a wide audience -from the scientific community, over climate and environmental service and agencies, environmental reporting and bodies to the general public. We will give here an overview on the report, highlight main outcomes, and introduce future plans and developments.

  6. Monitoring of the aquatic environment by species accumulator of pollutants: a review

    Directory of Open Access Journals (Sweden)

    Oscar RAVERA

    2001-09-01

    Full Text Available This paper is a short review on the biomonitoring of aquatic environments by animal and plant species accumulators of toxic pollutants ("scavengers". This monitoring is based on the relationship between the pollutant concentration in the organism and that in its environment, and not on alterations produced by pollution on the biota. The latter is the basis of other types of biomonitoring, such as those based on the biotic and diversity indices and saprobic scale. The various aspects of monitoring by pollutant accumulators are illustrated; for example, the uptake and loss of pollutants, the "critical organs" and "tissues", the detoxification mechanisms and the most common factors (C.F., BAF, BSAF for establishing a connection between the pollutant concentration in the organism and that in its environment. Several examples of this monitoring on heavy metals, radioisotopes and organic micropollutants are reported. The advantages of this monitoring, the characteristics of the species to be used as bioaccumulators and some practical suggestions are listed. A close collaboration between the scientific teams working on the biomonitoring based on accumulator organisms and on the chemical monitoring is recommended from the scientific and economic point of view.

  7. Remote physiological monitoring in an austere environment: a future for battlefield care provision?

    Science.gov (United States)

    Smyth, Matthew J; Round, J A; Mellor, A J

    2018-05-14

    Wearable technologies are making considerable advances into the mainstream as they become smaller and more user friendly. The global market for such devices is forecasted to be worth over US$5 billion in 2018, with one in six people owning a device. Many professional sporting teams use self-monitoring to assess physiological parameters and work rate on the pitch, highlighting the potential utility for military command chains. As size of device reduces and sensitivity improves, coupled with remote connectivity technology, integration into the military environment could be relatively seamless. Remote monitoring of personnel on the ground, giving live updates on their physiological status, would allow commanders or medical officers the ability to manage their soldiers appropriately and improve combat effectiveness. This paper explores a proof of concept for the use of a self-monitoring system in the austere high altitude environment of the Nepalese Himalayas, akin to those experienced by modern militaries fighting in remote locations. It also reviews, in part, the historical development of remote monitoring technologies. The system allowed for physiological recordings, plotted against GPS position, to be remotely monitored in Italy. Examples of the data recorded are given and the performance of the system is discussed, including limitations, potential areas of development and how systems like this one could be integrated into the military environment. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  8. Passive sampling in regulatory chemical monitoring of nonpolar organic compounds in the aquatic environment

    NARCIS (Netherlands)

    Booij, K.; Robinson, C.D.; Burgess, R.M.; Mayer, P.; Roberts, C.A.; Ahrens, L.; Allan, I.J.; Brant, J.; Jones, L.; Kraus, U.R.; Larsen, M.M.; Lepom, P.; Petersen, J.; Pröfrock, D.; Roose, P.; Schäfer, S.; Smedes, F.; Tixier, C.; Vorkamp, K.; Whitehouse, P.

    2016-01-01

    We reviewed compliance monitoring requirements in the EuropeanUnion, the United States, and the Oslo-Paris Convention for the protection of themarine environment of the North-East Atlantic, and evaluated if these are met bypassive sampling methods for nonpolar compounds. The strengths

  9. Inter-comparison of personal monitors for nanoparticles exposure at workplaces and in the environment

    NARCIS (Netherlands)

    Todea, A.M.; Beckmann, S.; Kaminski, H.; Bard, D.; Bau, S.; Clavaguera, S.; Dahmann, D.; Dozol, H.; Dziurowitz, N.; Elihn, K.; Fierz, M.; Lidén, G.; Meyer-Plath, A.; Monz, C.; Neumann, V.; Pelzer, J.; Simonow, B.K.; Thali, P.; Tuinman, I.; Vleuten, A. van der; Vroomen, H.; Asbach, C.

    2017-01-01

    Personal monitors based on unipolar diffusion charging (miniDiSC/DiSCmini, NanoTracer, Partector) can be used to assess the individual exposure to nanoparticles in different environments. The charge acquired by the aerosol particles is nearly proportional to the particle diameter and, by

  10. Application of γ field theory based calculation method to the monitoring of mine nuclear radiation environment

    International Nuclear Information System (INIS)

    Du Yanjun; Liu Qingcheng; Liu Hongzhang; Qin Guoxiu

    2009-01-01

    In order to find the feasibility of calculating mine radiation dose based on γ field theory, this paper calculates the γ radiation dose of a mine by means of γ field theory based calculation method. The results show that the calculated radiation dose is of small error and can be used to monitor mine environment of nuclear radiation. (authors)

  11. IMAGE information monitoring and applied graphics software environment. Volume 2. Software description

    International Nuclear Information System (INIS)

    Hallam, J.W.; Ng, K.B.; Upham, G.L.

    1986-09-01

    The EPRI Information Monitoring and Applied Graphics Environment (IMAGE) system is designed for 'fast proto-typing' of advanced concepts for computer-aided plant operations tools. It is a flexible software system which can be used for rapidly creating, dynamically driving and evaluating advanced operator aid displays. The software is written to be both host computer and graphic device independent

  12. METHODS OF STATISTICAL MONITORING OF PROFESSIONAL ORIENTATION WORK OF SOCIAL EDUCATORS IN PERSONAL LEARNING ENVIRONMENTS

    Directory of Open Access Journals (Sweden)

    Oleksandr M. Korniiets

    2012-12-01

    Full Text Available The article deals with the application of social services WEB 2.0 for personal learning environment creation that is used for professional orientation work of social educator. The feedback is must be in personal learning environment for the effective professional orientation work. This feedback can be organized through statistical monitoring. The typical solution for organizing personal learning environment with built-in statistical surveys and statistical data processing is considered in the article. The possibilities of the statistical data collection and processing services on the example of Google Analytics are investigated.

  13. An Environment IoT Sensor Network for Monitoring the Environment

    Science.gov (United States)

    Martinez, K.; Hart, J. K.; Bragg, O.; Black, A.; Bader, S.; Basford, P. J.; Bragg, G. M.; Fabre, A.

    2016-12-01

    The Internet of Things is a term which has emerged to describe the increase of Internet connectivity of everyday objects. While wireless sensor networks have developed highly energy efficient designs they need a step-change in their interoperability and usability to become more commonly used in Earth Science. IoT techniques can bring many of these advances while reusing some of the technologies developed for low power sensing. Here we concentrate on developing effective use of internet protocols throughout a low power sensor network. This includes 6LowPAN to provide a mesh IPv6 network, 40mW 868 MHz CC1120 radio transceivers to save power but provide kilometre range, a CC2538 ARM® Cortex®-M3 as main processor and CoAP to provide a binary HTTP-like interface to the nodes. We discuss in detail a system we deployed to monitor periglacial, peat and fluvial processes in the Scottish Highlands. The system linked initial nodes 3km away further up the mountain 2km away and used a CoAP GET sequence from a base station in the valley to gather the data. The IPv6 addressing and tunnelling allowed direct connectivity to desktops in Southampton. This provides insights into how the combination of low power techniques and emerging internet standards will bring advantages in interoperability, heterogeneity, usability and maintainability.

  14. Monitoring of radioactivity in the UK environment. An annotated bibliography of current programmes

    International Nuclear Information System (INIS)

    2001-01-01

    With the continuing use of radioactive materials in industry, research and medicine, the public's awareness about the potential impact on human health and safety of any enhanced levels of radiation in the environment has heightened. All those involved recognise this concern and there has developed over the years a network of comprehensive monitoring systems designed to determine the levels of radiation to which members of the public are exposed. In the UK, many organisations carry out regular radioactivity monitoring programmes, and summaries of these programmes have been published in 1983, 1988 and 1992. The number of organisations carrying out monitoring, particularly in the local authority sector, increased rapidly following the Chernobyl incident in 1986 and later levelled off. This report updates those previous summaries, giving synopses of regular UK programmes whose results are published in report form, and of which the Department of the Environment, Transport and the Regions is currently aware

  15. Annual report on radioactive discharges and monitoring of the environment 1990. V. 2

    International Nuclear Information System (INIS)

    1991-01-01

    This Annual Report supplements the Health and Safety Annual Report of British Nuclear Fuels plc by providing more detailed information on radioactive discharges, monitoring of the environment and critical group doses. This report has been sub-divided into two complementary parts. Volume I includes annual data for each of the Company sites on radioactive discharges into the environment and the associated environmental monitoring programmes. The sites involved are: Sellafield where the main activities are irradiated nuclear fuel reprocessing and the Calder Hall nuclear station; the Drigg radioactive waste storage and disposal site; the Chapelcross nuclear power station; Springfields Works which manufactures nuclear fuels; Capenhurst Works where uranium isotopic enrichment plants are operated. Volume II reproduces the Certificates of Authorisation under which the Company operates and the statutory environmental monitoring programmes which relate to them. (author)

  16. Annual report on radioactive discharges and monitoring of the environment 1990. V. 1

    International Nuclear Information System (INIS)

    1991-01-01

    This Annual Report supplements the Health and Safety Annual Report of British Nuclear Fuels plc by providing more detailed information on radioactive discharges, monitoring of the environment and critical group doses. This report has been sub-divided into two complementary parts. Volume I includes annual data for each of the Company sites on radioactive discharges into the environment and the associated environmental monitoring programmes. The sites involved are: Sellafield where the main activities are irradiated nuclear fuel reprocessing and the Calder Hall nuclear station; the Drigg radioactive waste storage and disposal site; the Chapelcross nuclear power station; Springfields Works which manufactures nuclear fuels; Capenhurst Works where uranium isotopic enrichment plants are operated. Volume II reproduces the Certificates of Authorisation under which the Company operates and the statutory environmental monitoring programmes which relate to them. (author)

  17. Integration of wireless sensor networks into cyberinfrastructure for monitoring Hawaiian "mountain-to-sea" environments.

    Science.gov (United States)

    Kido, Michael H; Mundt, Carsten W; Montgomery, Kevin N; Asquith, Adam; Goodale, David W; Kaneshiro, Kenneth Y

    2008-10-01

    Monitoring the complex environmental relationships and feedbacks of ecosystems on catchment (or mountain)-to-sea scales is essential for social systems to effectively deal with the escalating impacts of expanding human populations globally on watersheds. However, synthesis of emerging technologies into a robust observing platform for the monitoring of coupled human-natural environments on extended spatial scales has been slow to develop. For this purpose, the authors produced a new cyberinfrastructure for environmental monitoring which successfully merged the use of wireless sensor technologies, grid computing with three-dimensional (3D) geospatial data visualization/exploration, and a secured internet portal user interface, into a working prototype for monitoring mountain-to-sea environments in the high Hawaiian Islands. A use-case example is described in which native Hawaiian residents of Waipa Valley (Kauai) utilized the technology to monitor the effects of regional weather variation on surface water quality/quantity response, to better understand their local hydrologic cycle, monitor agricultural water use, and mitigate the effects of lowland flooding.

  18. Review of passive accumulation devices for monitoring organic micropollutants in the aquatic environment

    International Nuclear Information System (INIS)

    Stuer-Lauridsen, Frank

    2005-01-01

    Over the past 15 years passive sampling devices have been developed that accumulate organic micropollutants and allow detection at ambient sub ng/l concentrations. Most passive accumulation devices (PADs) are designed for 1-4 weeks field deployment, where uptake is governed by linear first order kinetics providing a time weighted average of the exposure concentration. Semipermeable membrane devices (SPMDs) are the most comprehensively studied PADs, but other samplers may also be considered for aquatic monitoring purposes. The applicability of the PADs is reviewed with respect to commonly monitored aqueous matrices and compounds, the detection limits, and for use in quantitative monitoring related to requirements embedded in the EU Water Framework Directive, the US and EU Water Quality Criteria, and the Danish monitoring aquatic programme. The PADs may monitor >75% of the organic micropollutants of the programmes. Research is warranted regarding the uptake in PADs in low flow environments and for the development of samplers for polar organic compounds. - Major developments in the passive sampling of organic contaminants in aquatic environments will support future monitoring, compliance and research

  19. Viewing Integrated-Circuit Interconnections By SEM

    Science.gov (United States)

    Lawton, Russel A.; Gauldin, Robert E.; Ruiz, Ronald P.

    1990-01-01

    Back-scattering of energetic electrons reveals hidden metal layers. Experiment shows that with suitable operating adjustments, scanning electron microscopy (SEM) used to look for defects in aluminum interconnections in integrated circuits. Enables monitoring, in situ, of changes in defects caused by changes in temperature. Gives truer picture of defects, as etching can change stress field of metal-and-passivation pattern, causing changes in defects.

  20. Development on high precision monitoring technique of radon and thoron in environment

    International Nuclear Information System (INIS)

    Imaizumi, Masayuki; Hamada, Hiromasa; Goto, Masahiro; Nakazato, Hiroomi; Mori, Mitsuhiro

    1999-01-01

    In a field of the environmental management, many technical research and developments such as monitoring on drainage section and flowing speed change of groundwater, analysis on alternating flow phenomenon between surface water and groundwater, analysis on water leakage at a dam, forecasting of landslide, safety evaluation on ground due to detection of faults, have conducted. And, an application to analysis on gas flowing phenomenon from underground to atmosphere as a part of study on evaluation of effect of gas emitted from earth surface on the earth environment was investigated. This study aimed to elucidate behaviors of radon and thoron at environment and to develop a high precision monitoring technique on radon and thoron required to conduct an advanced application to a tracer in hydrology, applied geology, and environment engineering. (G.K.)

  1. Software for marine ecological environment comprehensive monitoring system based on MCGS

    Science.gov (United States)

    Wang, X. H.; Ma, R.; Cao, X.; Cao, L.; Chu, D. Z.; Zhang, L.; Zhang, T. P.

    2017-08-01

    The automatic integrated monitoring software for marine ecological environment based on MCGS configuration software is designed and developed to realize real-time automatic monitoring of many marine ecological parameters. The DTU data transmission terminal performs network communication and transmits the data to the user data center in a timely manner. The software adopts the modular design and has the advantages of stable and flexible data structure, strong portability and scalability, clear interface, simple user operation and convenient maintenance. Continuous site comparison test of 6 months showed that, the relative error of the parameters monitored by the system such as temperature, salinity, turbidity, pH, dissolved oxygen was controlled within 5% with the standard method and the relative error of the nutrient parameters was within 15%. Meanwhile, the system had few maintenance times, low failure rate, stable and efficient continuous monitoring capabilities. The field application shows that the software is stable and the data communication is reliable, and it has a good application prospect in the field of marine ecological environment comprehensive monitoring.

  2. [The marine coastal water monitoring program of the Italian Ministry of the Environment].

    Science.gov (United States)

    Di Girolamo, Irene

    2003-01-01

    The Ministry of the Environment carries out marine and coastal monitoring programs with the collaboration of the coastal Regions. The program in progress (2001-2003), on the basis of results of the previous one, has identified 73 particulary significant areas (57 critical areas and 16 control areas). The program investigates several parameters on water, plancton, sediments, mollusks and benthos with analyses fortnightly, six-monthly and annual. The main aim of these three year monitoring programs is to assess the quality of national marine ecosystem.

  3. Waste heat discharges in the aquatic environment -- impact and monitoring 2

    International Nuclear Information System (INIS)

    Kamath, P.R.

    1980-01-01

    Studies on ecological impacts, on fishes in particular, of waste heat discharges in the aquatic environment are briefly reviewed. These studies cover the susceptibility of fishes to disease and predation, population biology, parasite proliferation and its impact on fishes, synergistic effects due to heat and other stresses such as chemicals, pollutant, lowering of saturation limit of dissolved oxygen at elevated temperature and radioactivity. Experiences of monitoring waste heat discharges at the Rajasthan Atomic Power Station (RAPS) and the Tarapur Atomic Power Station (TAPS) are presented. Entrainment losses and impingement losses are also reviewed. Requirements for thermal monitoring are mentioned. (M.G.B.)

  4. Physical and chemical monitoring of environment components at Rirang and Eko Remaja West Kalimantan

    International Nuclear Information System (INIS)

    Sorot S, Achmad; Deddi, Eep; Wismawati, Titi; Widarti, Sri

    2002-01-01

    The aim of the environmental monitoring is to know the possibility change environmental component quality at Kalan area West Kalimantan. This monitoring activity has done parallel to the exploration and mining research on radioactive ore at Kalan area. The monitoring consist the activities such as river water sampling, stream sediments, soil, and pH. Water and sediment samples were taken from the same location as what been carried out at the previously research sampling. COD and BOD parameters of the water were been analyzed in field, while the other parameters were analyzed at Jakarta using spectrophotometer and Eberline alpha counter SACR5. Data obtained on BOD, COD, and heavy metal constant such as Ca, As, Mg, Fe, Ni, Zn, Cu, Pb, Mn, Mc, U, Th nad Ra lesser than that in 1997/1998 monitoring. Base on the criteria of EQAM, AMDAL the Rirang water quality (4.62 scales) and Eko Remaja water quality (4.76) are fairly good. Result of stream sediment and soil samples analysis are relatively close to 1997/1998 monitoring, except U and Th content were increase 1-5 %. Result of soil analysis on the parameters Ca, Ni, Zn, Cu, Pb, Mn, Mo, U, Th, and fe relatively same with the 1997/1998 monitoring, except the uranium content is lesser than that monitoring. The maximal radioactivity values were accepted is 0.4 Bq/l. Based on the physical and chemical assay of the river water, stream sediments, and soils samples shown that the quality of the environment was not deteriorating, that mean the exploration and mining research on radioactive ores are do not disturb the environment

  5. Progress in the domain of emissions tracking and environment radioactivity monitoring - Proceedings of the technical days organised by the SFRP Environment Section

    International Nuclear Information System (INIS)

    Calmet, Dominique; Calvez, Marianne; Rivasseau, Corinne Cea; Monfort, Marguerite; Manificat, Guillaume; Pierrard, Olivier; Couvez, Celine; Masson, Olivier; Bruno, Valerie; Renaud, Philippe; Genova, Zhana; Reynal, Nathalie; Le Coz, Eric; Tchilian, Nathalie; Diana, Jean-Jacques; Beguinel, Philippe; Cortes, Pierre; Puydarrieux, Stephane; Brun, Thierry; Devin, Patrick; Clavel, Benoit; Hemidy, Pierre-Yves; Gontier, Gilles; Delloye, Thierry; Mailliat, Alain; Ferreri, Giovanni; LECLERC, Elisabeth

    2015-11-01

    The Environment Section of the French Society of Radiation Protection (SFRP) organized a technical meeting on the progress made in the domain of emissions tracking and environment radioactivity monitoring. This document brings together the abstracts and the presentations (slides) of the different talks given at the meeting: 1 - Environment monitoring at the global, national and local scale: historical overview (Dominique CALMET, CEA); 2 - Evolution of radioactivity monitoring in the environment from 1960 to the present day (Guillaume MANIFICAT, IRSN); 3 - Euratom's legal framework (Zhana GENOVA, CTE); 4 - Main regulatory changes during the last decade (Nathalie REYNAL, ASN); 5 - Progress of standardization works on radioactive effluent emissions control and environment monitoring (Philippe BEGUINEL, BNEN); 6 - From operators' self-monitoring to ASN's inspections: a many components control system (Eric LE COZ, ASN); 7 - Control of effluents and emissions management at CEA Centres (Marianne CALVEZ, CEA); 8 - Liquid and gaseous effluents of ITER experimental facility: description and impacts (Pierre CORTES, IO); 9 - Effluents and emissions management strategy at AREVA NC La Hague facility (Stephane PUYDARRIEUX, AREVA); 10 - Radioactive effluents from nuclear facilities ongoing deconstruction: from dimensioning to real effluents (Benoit CLAVEL, EDF); 11 - Radionuclides decontamination process for liquid effluents using micro-algae at the laboratory scale (Corinne RIVASSEAU, CEA); 12 - Radioactive effluents from nuclear medicine services: management, monitoring and impact measurement methods (Nathalie TCHILIAN, ASN); 13 - Evolution history of effluents management and environment monitoring at the Solvay La Rochelle site (Thierry DELLOYE, SOLVAY); 14 - Different international approaches in effluents management and monitoring: example of French and German gaseous effluents - regulation, analyses, accounting rules (Jean-Jacques DIANA, ASN); 15 - Environment

  6. POPs monitoring and related activities by the Ministry of the Environment, Japan

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Yoshitoku; Enomoto, Yasutaka; Kazuko, Kazuko [Ministry of the Environment, Goverment of Japan (Japan)

    2004-09-15

    In Article 16 of Stockholm Convention for the global elimination of Persistent Organic Pollutants (POPs), it is written that ''comparable monitoring data'' reported by the Parties will be used for the ''effectiveness evaluation of the Convention''. A detailed evaluation scheme will be decided by the Conference of the Parties, but various technical aspects of this POPs monitoring were discussed by the international experts at UNEP Chemical's workshop on the development of Global POPs Monitoring held in Geneva in March 2003, and the guidance documents for the monitoring are now being prepared based on the results of the workshop. The Ministry of the Environment (MoE), Japan, has been conducting environmental monitoring of various pollutants including major POPs in Japan for more than two decades, and reported the results every year in a report ''Chemicals in the Environment'' (or KUROHON, meaning ''black book'' in Japanese). Originally a conventional GC/ECD method had been employed for the analysis of organochlorine chemicals (OCs) in biological samples. Then a GC/MS (low resolution) was introduced for OCs analysis in sediments and water, and GC/high resolution(HR)-MS method was introduced for dioxins analysis from around 1990. Due to general decline of POPs levels in the environment, the number of ND (not detected = less than detection limits) data had been increasing in recent years, and consequently it became difficult to extract temporal trends from the monitoring data. In 2002, MoE decided to reorganize the environmental monitoring framework in order to respond to the request of POPs convention, and re-started POPs monitoring by using more sensitive GC/HR-MS method for the analysis of nine POPs chemicals (dioxins and furans have already been monitored by the method; toxaphene is analyzed by GC/negative ionization-MS). The primary purpose of this reorganization is to reveal

  7. Monitoring the sedimentary carbon in an artificially disturbed deep-sea sedimentary environment

    Digital Repository Service at National Institute of Oceanography (India)

    Nath, B.N.; Khadge, N.H.; Nabar, S.; Raghukumar, C.; Ingole, B.S.; Valsangkar, A.B.; Sharma, R.; Srinivas, K.

    1 Author version: Environ. Monit. Assess., vol.184; 2012; 2829-2844 Monitoring the sedimentary carbon in an artificially disturbed deep-sea sedimentary environment B. Nagender Nath * , N.H. Khadge, Sapana Nabar, C. Raghu Kumar, B.S. Ingole... community two years after an artificial rapid deposition event. Publication of Seto Marine Biological Laboratory, 39(1), 17-27. Gage, J.D. (1978). Animals in deep-sea sediments. Proceedings of Royal Society of Edinburgh, 768, 77-93. Gage, J.D., & Tyler...

  8. Monitoring of radiation in the environment in the Netherlands. Results in 2000

    Energy Technology Data Exchange (ETDEWEB)

    Knetsch, G.J. (ed.)

    2002-07-01

    This report presents the results of radioactivity measurements in the environment in the Netherlands carried out by RIVM, RIZA, RIKZ and Inspectorate for Health Protection and Veterinary Public Health in 2000. Measurements of radioactivity have been carried out in airborne particulates, deposition, surface water, seawater, drinking water and food (honey, game, blueberry and mushrooms). Results for ambient dose equivalent rates have been obtained from the National Radioactivity Monitoring Network. No measurements were done in milk. In 2000 no elevated levels of radioactivity were found in the Dutch environment.

  9. Monitoring for radioactive materials releasing to environment in M310 reformatived nuclear power plant

    International Nuclear Information System (INIS)

    Yin Zhenyu; Yang Guangli; Xu Guang

    2012-01-01

    Airborne radioactive materials of nuclear power plant (NPP) releases to the environment from the stack of NPP. Radioactive liquid waste releases of the ocean, the fluvial and the lake through the liquid waste letdyke of NPP. Further more, a few radioactive waste may be taken out of the NPP by vehicle or personnel. For the purpose of strict management and control above-mentioned waste, we use detect equipment monitoring radioactive waste of NPP. Management and control for the releasing of radioactive material to the environment in M310 reformatived NPP is strict and safety. (authors)

  10. Monitoring of radiation in the environment in the Netherlands. Results in 2000

    CERN Document Server

    Knetsch, G J

    2002-01-01

    This report presents the results of radioactivity measurements in the environment in the Netherlands carried out by RIVM, RIZA, RIKZ and Inspectorate for Health Protection and Veterinary Public Health in 2000. Measurements of radioactivity have been carried out in airborne particulates, deposition, surface water, seawater, drinking water and food (honey, game, blueberry and mushrooms). Results for ambient dose equivalent rates have been obtained from the National Radioactivity Monitoring Network. No measurements were done in milk. In 2000 no elevated levels of radioactivity were found in the Dutch environment

  11. Real-Time Molecular Monitoring of Chemical Environment in ObligateAnaerobes during Oxygen Adaptive Response

    Energy Technology Data Exchange (ETDEWEB)

    Holman, Hoi-Ying N.; Wozei, Eleanor; Lin, Zhang; Comolli, Luis R.; Ball, David. A.; Borglin, Sharon; Fields, Matthew W.; Hazen, Terry C.; Downing, Kenneth H.

    2009-02-25

    Determining the transient chemical properties of the intracellular environment canelucidate the paths through which a biological system adapts to changes in its environment, for example, the mechanisms which enable some obligate anaerobic bacteria to survive a sudden exposure to oxygen. Here we used high-resolution Fourier Transform Infrared (FTIR) spectromicroscopy to continuously follow cellular chemistry within living obligate anaerobes by monitoring hydrogen bonding in their cellular water. We observed a sequence of wellorchestrated molecular events that correspond to changes in cellular processes in those cells that survive, but only accumulation of radicals in those that do not. We thereby can interpret the adaptive response in terms of transient intracellular chemistry and link it to oxygen stress and survival. This ability to monitor chemical changes at the molecular level can yield important insights into a wide range of adaptive responses.

  12. On the Relevance of Using OpenWireless Sensor Networks in Environment Monitoring

    Directory of Open Access Journals (Sweden)

    Antoine B. Bagula

    2009-06-01

    Full Text Available This paper revisits the problem of the readiness for field deployments of wireless- sensor networks by assessing the relevance of using Open Hardware and Software motes for environment monitoring. We propose a new prototype wireless sensor network that finetunes SquidBee motes to improve the life-time and sensing performance of an environment monitoring system that measures temperature, humidity and luminosity. Building upon two outdoor sensing scenarios, we evaluate the performance of the newly proposed energy-aware prototype solution in terms of link quality when expressed by the Received Signal Strength, Packet Loss and the battery lifetime. The experimental results reveal the relevance of using the Open Hardware and Software motes when setting up outdoor wireless sensor networks.

  13. A Design of Ginseng Planting Environment Monitoring System Based on WSN

    Directory of Open Access Journals (Sweden)

    Xin Ding

    2014-03-01

    Full Text Available Through the analysis of ginseng products industry chain, this paper designs and implements ginseng planting environment monitoring system. The system realized data collection and detection of ginseng planting environment in real time by using wireless sensor, transmission of environmental parameters in real time by using GPRS wireless transmission module, and video monitor and alarm of ginseng land by using unattended machine. It is the foundation of information transformation of ginseng products industry chain based on the Internet of Things. The experiment of ginseng planting base in Fusong indicates the system can offer support of original data for scientific cultivation of ginseng, comprehensive analysis of ginseng products and propaganda of ginseng brand.

  14. Monitoring of radioactivity in the environs of Finnish nuclear power stations in 1986

    International Nuclear Information System (INIS)

    Ilus, E.; Sjoeblom, K.L.; Aaltonen, H.; Klemola, S.; Arvela, H.

    1987-06-01

    Results of the environmental programmes monitoring radioactivity around the Finnish nuclear power stations in 1986 are reported. After the end of April the fallout nuclides from the Chernobyl accident predominated in all samples taken from the environs of the two power stations Loviisa and Olkiluoto. Radionuclides originating from the Finnish power stations were detected mainly in samples taken from the aquatic environment. The concentrations of the locally discharged nuclides were very low in comparison with the fallout nuclides and their impact on the radiation doses of the population was insignificant. Both nuclear power stations are situated in the main fallout area in Finland. The results of these large monitoring programmes give a good picture of the behaviour of the Chernobyl fallout in the specific areas in Finland

  15. Sentinel-1 provides ice drift observations for Copernicus Marine Environment Monitoring Service (CMEMS)

    DEFF Research Database (Denmark)

    Toudal Pedersen, Leif; Saldo, Roberto

    are matched every month in the processing system.The quality of the ice drift vectors are routinely verified against GPS locations of drift buoys and the RMS difference between the baseline product available through the Copernicus Marine Environment Monitoring Service data portal and GPS drifters is ~500......Sea ice drift information with an accuracy that allows also ice deformation (divergence, shear, vorticity) to be derived is being operationally generated in the Copernicus Marine Environment Monitoring Service (CMEMS).The method is based on 2-dimensional digital cross correlation where subsections......View project in 2007 when large volumes of ENVISAT ASAR images of the Polar regions became available during the International Polar Year. A dataset of daily ice drift vectors of the Polar Regions (North and South) is now available covering the time period from 2007 to the present time.In 2009 the processing...

  16. APPLICATION OF KATG::LUX GENE CONSTRUCT FOR CYTOTOXICITY AND GENOTOXICITY MONITORING OF METOPROLOL IN ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    Eliza Hawrylik

    2017-06-01

    Full Text Available The aim of the study was the evaluation of usefulness of Escherichia coli K-12 RFM 443 katG::lux for cytotoxicity and genotoxicity monitoring of metoprolol in the environment. Metoprolol is one of the most popular cardiac drug which belongs to the group of β – blockers. The drug was applied at concentrations ranging from 10-1 mg/cm3 to 10-5 mg/cm3. Obtained data indicated the influence of metoprolol on lux gene expression and katG promotor activity in E.coli K-12. The results indicato the possibility of using of Escherichia coli K-12 RFM 443 strain with katG::lux gene construct in the monitoring of cytotoxicity and genotoxicity cardiac drug residues in the environment.

  17. Monitoring of radionuclides in the environs of the Finnish nuclear power stations in 1988

    International Nuclear Information System (INIS)

    Klemola, S.; Ilus, E.; Sjoeblom, K.L.; Arvela, H.; Blomqvist, L.

    1991-03-01

    Monitoring of radionuclides around Finnish nuclear power plants continued in 1988 with the regular programmes. About 1000 samples were analysed from both terrestrial and aquatic environments.The dominant artificial radioactive substances in the vicinity of power plants were still the fallout nuclides from the Chernobyl accident, but the concentrations in all the objects monitored are lower than in the previous year. Trace amounts of activation products originating from the airborne releases of local power plants were detected in some air and deposition samples. Discharged nuclides were more abundant in the aquatic environment, especially in samples of indicator organisms. However, their contribution to the radiation doses received by the the public was very small. (orig.)

  18. Integrity mechanism for eHealth tele-monitoring system in smart home environment.

    Science.gov (United States)

    Mantas, Georgios; Lymberopoulos, Dimitrios; Komninos, Nikos

    2009-01-01

    During the past few years, a lot of effort has been invested in research and development of eHealth tele-monitoring systems that will provide many benefits for healthcare delivery from the healthcare provider to the patient's home. However, there is a plethora of security requirements in eHealth tele-monitoring systems. Data integrity of the transferred medical data is one of the most important security requirements that should be satisfied in these systems, since medical information is extremely sensitive information, and even sometimes life threatening information. In this paper, we present a data integrity mechanism for eHealth tele-monitoring system that operates in a smart home environment. Agent technology is applied to achieve data integrity with the use of cryptographic smart cards. Furthermore, the overall security infrastructure and its various components are described.

  19. Taimyr Reindeer and Environmental Change: Monitoring Wild Reindeer Migration in Changing Natural and Social Environments

    Science.gov (United States)

    Petrov, A. N.

    2016-12-01

    The Taimyr Reindeer Herd (TRH) is both the largest and the longest monitored wild reindeer herd in Eurasia. An important part of Arctic ecosystems and Indigenous livelihood, wild reindeer have been continuously monitored for almost 50 years. During this time, herds have exhibited large changes in size and these changes have been recorded in almost all herds across the animal's range. An increasing number of wild reindeer in the Soviet times was followed by a significant population loss in the last decade. In addition, recent monitoring revealed substantial shifts in the distribution of wild populations. The decline in wild reindeer is likely related to natural cycles and changes in the Arctic environment caused by climate variability and anthropogenic activity. This study investigates patterns and possible drives of reindeer population dynamics in space and time. We identify key climatic factors, possible relationships with biomass dynamics, as well as with hunting practices and other human impacts.

  20. Construction and application of an intelligent air quality monitoring system for healthcare environment.

    Science.gov (United States)

    Yang, Chao-Tung; Liao, Chi-Jui; Liu, Jung-Chun; Den, Walter; Chou, Ying-Chyi; Tsai, Jaw-Ji

    2014-02-01

    Indoor air quality monitoring in healthcare environment has become a critical part of hospital management and policy. Manual air sampling and analysis are cost-inhibitive and do not provide real-time air quality data and response measures. In this month-long study over 14 sampling locations in a public hospital in Taiwan, we observed a positive correlation between CO(2) concentration and population, total bacteria, and particulate matter concentrations, thus monitoring CO(2) concentration as a general indicator for air quality could be a viable option. Consequently, an intelligent environmental monitoring system consisting of a CO(2)/temperature/humidity sensor, a digital plug, and a ZigBee Router and Coordinator was developed and tested. The system also included a backend server that received and analyzed data, as well as activating ventilation and air purifiers when CO(2) concentration exceeded a pre-set value. Alert messages can also be delivered to offsite users through mobile devices.

  1. Matchmaking: the influence of monitoring environments on the effectiveness of performance pay systems

    OpenAIRE

    Richard Belfield; David Marsden

    2002-01-01

    This study uses cross-section and panel data from the 1998 Workplace Employee Relations Survey to explore contextual influences on the relationship between performance-related pay (PRP) and organizational performance. While it finds strong evidence that the use of PRP can enhance performance outcomes, it also determines that this relationship is qualified by the structure of workplace monitoring environments. In addition, it presents evidence that managers learn about optimum combinations of ...

  2. Development of an Indoor Airflow Energy Harvesting System for Building Environment Monitoring

    OpenAIRE

    Fei Fei; Shengli Zhou; John D. Mai; Wen Jung Li

    2014-01-01

    Wireless sensor networks (WSNs) have been widely used for intelligent building management applications. Typically, indoor environment parameters such as illumination, temperature, humidity and air quality are monitored and adjusted by an intelligent building management system. However, owing to the short life-span of the batteries used at the sensor nodes, the maintenance of such systems has been labor-intensive and time-consuming. This paper discusses a battery-less self-powering system that...

  3. Marine outfalls monitoring at the CSIR: Evaluating the impact of wastewater discharge on our marine environment

    CSIR Research Space (South Africa)

    Arabi, S

    2012-10-01

    Full Text Available is used in coastal cities throughout the world and, if correctly managed, is recognised as an acceptable disposal option from multiple perspectives, including human and environmental health, social acceptability, and economic prudence. However..., wastewater contains contaminants that can affect the ecological functioning of the marine environment and compromise human health. The impact of wastewater discharge therefore requires careful monitoring. The CSIR uses a wide suite of indicators...

  4. Summary 1998. Releases control and environment monitoring for the CEA Centers

    International Nuclear Information System (INIS)

    1998-01-01

    In the framework of its environmental policy, the CEA aims at reduce as weak as possible, in regards to the technological and economic needs, its activities impacts on the people and the environment. This paper contributes to the public information on the radioactive gaseous and liquid releases during the year 1998. It presents data on the releases and the radioactivity levels around the CEA sites and gathers the associated regulation and monitoring methods. (A.L.B.)

  5. Harnessing monitoring measurements in urban environments for decision making after nuclear accidents

    International Nuclear Information System (INIS)

    Kaiser, J.C.; Proehl, G.

    2007-01-01

    This article gives an overview on the conceptual design of the Inhabited Areas Monitoring Module IA MM which will be introduced into European decision support systems for nuclear emergencies. It will improve the use of monitoring data of radioactive contamination in urban environments for decision making. IAMM converts the dated gamma dose rate (GDR) measurements from geo-referenced locations into maps of surface contamination with an enhanced spatial resolution. Depending on the availability of the monitoring data, IAMM relies on two modes of operation. If there are only a few measurements, these are taken to improve the maps from a deposition model using data assimilation. If the number of measurements is sufficient to apply spatial interpolation IAMM will rely entirely on monitoring data. Suitable geo-referenced data points will be interpreted by IAMM with respect to their detector environment using the concept of location factors. The endpoints of IAMM can be used directly for decision making or dose calculations with either simple dose models or the more refined EuRopean Model for INhabited areas (ERMIN). (orig.)

  6. Initiation of environment protection monitoring system in energetic sector of Sartid Iron and Steel Factory

    International Nuclear Information System (INIS)

    Janjic, Jovan; Ivanovic, Jovan

    2003-01-01

    Energetic sector in SARTID Iron and Steel factory includes complex systems for production, transformation and distribution of all kinds of energy and fluids, supplying all other production divisions. As that, energetic sector has large influence in environment. Incorporating quality system ISO 14001 in SARTID factory, with special care we are working on environment protection monitoring system. Having started with this, as first we are working on implementation of monitoring system for air pollution from our emitters of exhausted gases issued from incineration of blast furnace (BF) gas, natural gas and crude oil. Constant recording of air pollutant emissions from our boilers have became standard procedure now. This monitoring system is based on software package, where input data are permanently measured flow of fuels, fuel composition and quality of combustion. As a result, in each time we know quantity of emitted exhausted components - CO 2 , CO, SO 2 , (NO) x . Another monitoring system that we are implementing right now is some simpler, being used for a lot of smaller BF or natural gas consumers. (Original)

  7. LYSIMETER - A UNIQUE TOOL FOR MONITORING THE INTERACTIONS AMONG THE COMPONENTS OF ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    Ivan Matušek

    2016-06-01

    Full Text Available Modern lysimeter facilities in connection with meteorological stations allow monitoring and evaluation of mutual basic components of the environment, such as water, air, soil and vegetation. Water is the most important component of the ecosystem and the component which connects all the other components. Therefore, we need to know the basic distribution and water balance in the different components of the environment to be able to interpret some processes in nature. Rainfall, which is the primary source of vital processes in the soil, is formed in the air. The amount of precipitation that gets into the soil and into the groundwater is affected by weather conditions. Primary distribution of rainwater is divided between infiltration, surface runoff, transpiration and evapotranspiration. The amount of water infiltrated into the soil and then evaporated by solar activity or activities of plants can be identified primarily by monitoring changes in weight. For this monitoring we use weighable lysimeter. This equipment with the monolith size of surface area 1 m2 and the depth of 1.5 m is able to follow online updates of weight of the 2 ton body with an accuracy of 100 g. When we add to quantification of leakages through the bottom layer, we obtain a comprehensive record of rainfall at the time in the natural environment of the individual components. The obtained data can be further interpreted in terms of the needs of hydrology, agriculture, and environmental studies, and according to the purpose and objectives for which we want to use them.

  8. Process monitoring in high volume semiconductor production environment with in-fab TXRF

    International Nuclear Information System (INIS)

    Ghatak-Roy, A.R.; Hossain, T.Z.

    2000-01-01

    After its introduction in the 80's, TXRF has become an important tool for surface contamination analysis. This is particularly true for the semiconductor industries, where monitoring trace level contamination in ultra clean environment is absolutely necessary for successful device production with reasonable yield. In FAB 25 of the Advanced Micro Devices in Austin, we have installed two TXRF tools, which are model TXRF3750 manufactured by Rigaku. They contain rotating tungsten anodes with three beam capability for wide selection of elements. One of the beams (WM) is used for monitoring of low Z elements such as Na, Mg and Al. The standard output is 9 kW with 300 mA at 30 kV. The tool runs 24 hours a day, 7 days a week, except for maintenance and breakdowns. We have been using TXRF for in-fab monitoring of various tools and processes for trace contamination and some quantification of materials. This in-fab operation is important because it gives real time monitoring without the necessity of bringing the wafers out of the fab. Secondly, being in ultra clean fab environment, the risk of background contamination is minimized. Since TXRF measurement is fast and does not need any sample preparation, this works very well as production support tool. Several wafer fab technicians have been trained to use the tool for round the clock operation. We have successfully monitored tools and processes in our fab. One example is the monitoring of numerous sinks used in the cleaning of production wafers after various processes. Monitor wafers are run after sink cleaning and solvent changes and they are then analyzed for any contamination. Another example is the monitoring of tools that use Ferrofluidic seals so as to prevent any contamination from Fe and Cr. Other tools using TXRF include diffusion furnaces, etchers and plasma cleaning tools. We have also been monitoring processes such as ion implantation, metal deposition and rapid thermal annealing. In this presentation, we will

  9. Design of environment monitoring system to evaluate radionuclide release from subsystem on PWR nuclear power accident

    International Nuclear Information System (INIS)

    Sri Kuntjoro; Sugiyanto; Pande Made Udiyani; Jupiter Sitorus Pane

    2012-01-01

    Nuclear Power Plan (NPP) as a renewable energy source is selected as an alternative, because it has many advantages that is environmentally friendly, fuel supply which is independent of the season, and the price that can compete with other power plants. However, the existence of some public skepticism about nuclear radiation safety, the government must be convinced about the operation of nuclear power plants are safe and secure. Research on the design of environment monitoring system for evaluation of radionuclide release from the reactor subsystems and the environment due to accidents at power reactors has been done. The study was conducted by calculating the distribution of radionuclide release into the reactor subsystem and the environment and also to build the environment radiation monitoring system. Environmental monitoring system consists of a radiation counter, early warning systems, meteorological measurement systems, GPS systems and GIS. Radiation monitoring system used to record the data of radiation, meteorological measurement system used to record data of wind and speed direction, while the GPS system is used to determine position of data measurements. The data is then transmitted to a data acquisition system and then to be transmitted to the control center. Collection and transmission of data is done via SMS formatting using a modem device that is placed in the control center. The control center receives measurement data from various places. In this case the control center has a function as an SMS Gateway. This system can visualize for different measurement locations. Furthermore, radiation data and position data to be integrated with digital maps. System integration is then visualized in a personal computer. To position of measurements directly visualized on the map and also look for the data displayed on a monitor as a red or green circle colour. That colour indicated as a safe limit of radiation monitor. When the cycle colour is red, the system will

  10. AVHRR-based drought-observing system for monitoring the environment and socioeconomic activities

    Science.gov (United States)

    Kogan, F.

    From all natural disaster, drought is the least understandable and the most damaging environmental phenomenon. Although in pre-satellite era, climate data were used for drought monitoring, drought specifics created problems in early drought detection start/end, monitoring its expansion/contraction, intensity and area coverage and the most important, timely estimation of the impacts on the environment and socioeconomic activities. The latest prevented to take prompt measures in mitigating negative consequences of drought for the society. Advances in remote sensing of the past ten years, contributed to the development of comprehensive drought monitoring system and numerous applications, which helped to make decisions for monitoring the environment and predicting sustainable socioeconomic activities. This paper discusses satellite-based land-surface observing system, which provides wells of information used for monitoring such unusual natural disaster as drought. This system was developed from the observations of the Advanced Very High Resolution Radiometer (AVHRR) flown on NOAA operational polar-orbiting satellites. The AVHRR data were packed into the Global Vegetation Index (GVI) product, which have served the global community since 1981. The GVI provided reflectances and indices (4 km spacial resolution) every seven days for each 16 km map cell between 75EN and 55ES covering all land ecosystems. The data includes raw and calibrated radiances in the visible, near infrared and infrared spectral bands, processed (with eliminated high frequency noise) radiances, normalized difference vegetation index (NDVI), 20-year climatology, vegetation condition indices and also products, such as vegetation health, drought, vegetation fraction, fire risk etc. In the past ten years, users around the world used this information addressing different issues of drought impacts on socioeconomic activities and responded positively to real time drought information place regularly on the

  11. Wireless sensor network-based greenhouse environment monitoring and automatic control system for dew condensation prevention.

    Science.gov (United States)

    Park, Dae-Heon; Park, Jang-Woo

    2011-01-01

    Dew condensation on the leaf surface of greenhouse crops can promote diseases caused by fungus and bacteria, affecting the growth of the crops. In this paper, we present a WSN (Wireless Sensor Network)-based automatic monitoring system to prevent dew condensation in a greenhouse environment. The system is composed of sensor nodes for collecting data, base nodes for processing collected data, relay nodes for driving devices for adjusting the environment inside greenhouse and an environment server for data storage and processing. Using the Barenbrug formula for calculating the dew point on the leaves, this system is realized to prevent dew condensation phenomena on the crop's surface acting as an important element for prevention of diseases infections. We also constructed a physical model resembling the typical greenhouse in order to verify the performance of our system with regard to dew condensation control.

  12. Wireless Sensor Network-Based Greenhouse Environment Monitoring and Automatic Control System for Dew Condensation Prevention

    Science.gov (United States)

    Park, Dae-Heon; Park, Jang-Woo

    2011-01-01

    Dew condensation on the leaf surface of greenhouse crops can promote diseases caused by fungus and bacteria, affecting the growth of the crops. In this paper, we present a WSN (Wireless Sensor Network)-based automatic monitoring system to prevent dew condensation in a greenhouse environment. The system is composed of sensor nodes for collecting data, base nodes for processing collected data, relay nodes for driving devices for adjusting the environment inside greenhouse and an environment server for data storage and processing. Using the Barenbrug formula for calculating the dew point on the leaves, this system is realized to prevent dew condensation phenomena on the crop’s surface acting as an important element for prevention of diseases infections. We also constructed a physical model resembling the typical greenhouse in order to verify the performance of our system with regard to dew condensation control. PMID:22163813

  13. Monitoring of radionuclides in the environs of Finnish nuclear power plants in 1989-1990

    International Nuclear Information System (INIS)

    Ilus, E.; Sjoeblom, K-L.; Klemola, S.; Arvela, H.

    1992-01-01

    Surveillance of radioactive substances around Finnish nuclear power plants continued in 1989-1990 according to the regular monitoring programmes. About 1000 samples were analysed annually from both terrestrial and aquatic environments. The dominant artificial radionuclides in the vicinity of the power plants were still the cesium isotopes, 137 Cs and 134 Cs, originating from the Chernobyl accident. Owing to radioactive decay, other fallout nuclides with shorter half-lives disappeared from the environmental samples during the period in question. Trace amounts of activation products originating from the airborne releases of the local power plants were detected in some air and deposition samples. Discharged nuclides were more abundant in the aquatic environment, especially in samples of indicator organisms and sinking matter collected from the Olkiluoto area in 1990. However, the concentrations were so low that they did not markedly raise the radiation burden in the environment. (orig.)

  14. Quality assurance for the measurements and monitoring of radioactivity in the environment

    International Nuclear Information System (INIS)

    Betti, Maria; Aldave de las Heras, Laura

    2004-01-01

    During the Fifth Framework Programme (FP5) of the European Commission--according to an institutional programme in support to the policy of the European Commission for the implementation of Art. 35 and 36 of the Euratom Treaty as well as in the framework of the OSPAR Convention for the protection of marine environment of the north-east Atlantic--at the Institute for Transuranium Elements (ITU-General Directorate Joint Research Centre-European Commission), a reference laboratory for the measurement of radioactivity in the environment (MaRE laboratory) has been set up. In this paper, the principles and philosophy in order to improve the quality and reliability of analytical data for the measurement and monitoring of radioactivity in the environment under a quality assurance (QA) programme are presented. Examples of how a QA programme at the MaRE laboratory is developed and applied are given. Internal and external quality control (QC) programmes are also discussed

  15. Real-time continuous glucose monitoring systems in the classroom/school environment.

    Science.gov (United States)

    Benassi, Kari; Drobny, Jessica; Aye, Tandy

    2013-05-01

    Children with type 1 diabetes (T1D) spend 4-7 h/day in school with very little supervision of their diabetes management. Therefore, families have become more dependent on technology, such as use of real-time continuous glucose monitoring (RT-CGM), to provide increased supervision of their diabetes management. We sought to assess the impact of RT-CGM use in the classroom/school environment. Children with T1D using RT-CGM, their parents, and teachers completed a questionnaire about RT-CGM in the classroom/school environment. The RT-CGM was tolerated well in the classroom/school environment. Seventy percent of parents, 75% of students, and 51% of teachers found RT-CGM useful in the classroom/school environment. The students found the device to be more disruptive than did their parents and teachers. However, all three groups agreed that RT-CGM increased their comfort with diabetes management at school. Our study suggests that RT-CGM is useful and not disruptive in the classroom/school environment. The development of education materials for teachers could further increase its acceptance in the classroom/school environment.

  16. Radioactivity in the environment. Report for 1999. A summary and radiological assessment of the Environment Ageny's monitoring programmes

    International Nuclear Information System (INIS)

    1999-01-01

    The Environment Agency has wide-ranging responsibilities and powers to protect and, where necessary, improve the environment in England and Wales. The Agency also has a duty to protect the environment in a way that works towards sustainable development. In 1998, the Oslo and Paris Commission (OSPAR) strategy for radioactive substances was agreed by Ministers at Sintra, Portugal, to prevent pollution of the North East Atlantic maritime area through progressive and substantial reductions in discharges, emissions and losses of radioactive substances. In June 2000, the UK Government published for consultation the draft UK Strategy for Radioactive Discharges 2001-2020 which sets out the UK's plans to implement the OSPAR strategy. The Government will be issuing statutory guidance to the Environment Agency which will provide the vehicle through which the UK Strategy will be implemented. Radiological monitoring programmes are carried out in support of the Agency's regulatory functions under RSA 93 and as part of the UK Government's obligations under the Euratom Treaty. This report presents the results of the Agency's regular monitoring of radioactivity in the environment during 1999 and an assessment of the radiological impact. The main findings of the regular monitoring programme during 1999 were as follows: (i) The majority of operator declarations of the radioactive content of wastes discharges and disposals had been assessed accurately or were over estimated. (ii) Radiation dose-rates above sediments and concentrations of radionuclides in water, sediment, soil and grass were generally consistent with those reported in previous years, with no clear trend over the last 10 years. Enhanced levels of artificial radionuclides continue to be found in coastal sediments in the vicinity of Sellafield, which decline with increasing distance from the site. Radioactivity levels around other major sites were mostly low or not detectable. (iii) As in previous years, concentrations of

  17. Relations Between Self-Reported and Linguistic Monitoring Assessments of Affective Experience in an Extreme Environment.

    Science.gov (United States)

    Smith, Nathan

    2018-03-01

    Approaches for monitoring psychosocial health in challenging environments are needed to maintain the performance and safety of personnel. The purpose of the present research was to examine the relationship between 2 candidate methods (self-reported and linguistics) for monitoring affective experience during extreme environment activities. A single-subject repeated-measures design was used in the present work. The participant was a 46-year-old individual scheduled to complete a self-supported ski expedition across Arctic Greenland. The expedition lasted 28 days, and conditions included severe cold, low stimulation, whiteouts, limited habitability, and threats to life and limb. During the expedition, the participant completed a daily self-report log including assessment of psychological health (perceptions of control and affect) and a video diary (emotion). Video diary entries were subjected to linguistic inquiry and word count analyses before the links between self-report and linguistic data across the expedition period were tested. Similarities in the pattern of self-reported and linguistic assessments emerged across the expedition period. A number of predictable correlations were identified between self-reported and linguistic assessments of affective/emotional experience. Overall, there was better agreement between self-reports and linguistic analytics for indicators of negative affect/emotion. Future research should build on this initial study to further test the links between self-reported affect and emotional states monitored via linguistics. This could help develop methods for monitoring psychological health in extreme environments and support organizational decision making. Crown Copyright © 2017. Published by Elsevier Inc. All rights reserved.

  18. Radioactivity in the environment. Report for 2001 : a summary and radiological assessment of the Environment Agency's monitoring programmes

    International Nuclear Information System (INIS)

    2003-01-01

    RSA 93 authorisations. Radiological monitoring programmes are carried out in support of the Agency's regulatory functions under RSA 93 and as part of the UK Government's obligations under the Euratom Treaty. This report presents the results of the Agency's regular monitoring of radioactivity in the environment during 2001 and an assessment of the radiological impact. The main findings of the regular monitoring programme during 2001 were as follows: The majority of operator declarations of the radioactive content of waste discharges and disposals had been assessed accurately or were over-estimate; Radiation dose rates above sediments and concentrations of radionuclides in water, sediment, soil and grass were generally consistent with those reported in previous years. Enhanced levels of artificial radionuclides continue to be found in coastal sediments in the vicinity of Sellafield, which decline with increasing distance from the site. Radioactivity levels around other major sites were mostly low or not detectable; As in previous years, concentrations of radionuclides in samples of airborne dust and rainwater from seven locations in the UK were very low or undetectable; Water from all 31 monitored sources of drinking water in England and Wales, except one in Derbyshire, were consistently below the World Health Organisation (WHO) drinking water screening levels. The enhanced level of uranium in the Derbyshire water is due to the natural levels of uranium in the local geology, and is insignificant from a radiological point of view. Assessments of doses that might be received by members of the public from drinking water and occupation of beaches, inter-tidal areas and river banks around nuclear and major non-nuclear sites were made. In all cases, doses were less than the annual dose limit for members of the public of 1000 microsieverts (1000 μSv). Houseboat dwellers on the Ribble Estuary in Lancashire received the highest total annual dose of 142 μSv. This is due to

  19. Embedded Active Fiber Optic Sensing Network for Structural Health Monitoring in Harsh Environments

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Anbo [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States)

    2016-09-30

    This report summarizes technical progress on the program “Embedded Active Fiber Optic Sensing Network for Structural Health Monitoring in Harsh Environments” funded by the National Energy Technology Laboratory of the U.S. Department of Energy, and performed by the Center for Photonics Technology at Virginia Tech. The objective of this project is to develop a first-of-a-kind technology for remote fiber optic generation and detection of acoustic waves for structural health monitoring in harsh environments. During the project period, which is from April 1, 2013 to Septemeber 30, 2016, three different acoustic generation mechanisms were studied in detail for their applications in building a fiber optic acoustic generation unit (AGU), including laser induced plasma breakdown (LIP), Erbium-doped fiber laser absorption, and metal laser absorption. By comparing the performance of the AGUs designed based on these three mechanisms and analyzing the experimental results with simulations, the metal laser absorption method was selected to build a complete fiber optic structure health monitoring (FO-SHM) system for the proposed high temperature multi-parameter structure health monitoring application. Based on the simulation of elastic wave propagation and fiber Bragg grating acoustic pulse detection, an FO-SHM element together with a completed interrogation system were designed and built. This system was first tested on an aluminum piece in the low-temperature range and successfully demonstrated its capability of multi-parameter monitoring and multi-point sensing. In the later stages of the project, the research was focused on improving the surface attachment design and preparing the FO-SHM element for high temperature environment tests. After several upgrades to the surface attachment methods, the FO-SHM element was able to work reliably up to 600oC when attached to P91 pipes, which are the target material of this project. In the final stage of this project, this FO

  20. Unmanned Aerial Vehicle Based Wireless Sensor Network for Marine-Coastal Environment Monitoring.

    Science.gov (United States)

    Trasviña-Moreno, Carlos A; Blasco, Rubén; Marco, Álvaro; Casas, Roberto; Trasviña-Castro, Armando

    2017-02-24

    Marine environments are delicate ecosystems which directly influence local climates, flora, fauna, and human activities. Their monitorization plays a key role in their preservation, which is most commonly done through the use of environmental sensing buoy networks. These devices transmit data by means of satellite communications or close-range base stations, which present several limitations and elevated infrastructure costs. Unmanned Aerial Vehicles (UAV) are another alternative for remote environmental monitoring which provide new types of data and ease of use. These aircraft are mainly used in video capture related applications, in its various light spectrums, and do not provide the same data as sensing buoys, nor can they be used for such extended periods of time. The aim of this research is to provide a flexible, easy to deploy and cost-effective Wireless Sensor Network (WSN) for monitoring marine environments. This proposal uses a UAV as a mobile data collector, low-power long-range communications and sensing buoys as part of a single WSN. A complete description of the design, development, and implementation of the various parts of this system is presented, as well as its validation in a real-world scenario.

  1. The environment, international standards, asset health management and condition monitoring: An integrated strategy

    Energy Technology Data Exchange (ETDEWEB)

    Roe, S. [CSD, British Institute of Non-Destructive Testing (BINDT) (United Kingdom); Mba, D. [School of Engineering, Cranfield University, MK43 0AL, Bedfordshire (United Kingdom)], E-mail: d.mba@cranfield.ac.uk

    2009-02-15

    Asset Health Management (AHM), supported by condition monitoring (CM) and performance measuring technologies, together with trending, modelling and diagnostic frameworks, is not only critical to the reliability of high-value machines, but also to a companies Overall Equipment Efficiency (OEE), system safety and profitability. In addition these protocols are also critical to the global concern of the environment. Industries involved with monitoring key performances indicators (KPI) to improve OEE would benefit from a standardised qualification and certification scheme for their personnel, particularly if it is based on internationally accepted procedures for the various CM technologies that also share the same objectives as AH and CM. Furthermore, the development of 'models' for implementation of a Carbon tax is intrinsically dependent on the integrity and accuracy of measurements contributing to these indicators. This paper reviews the global picture of condition monitoring, the environment and related international standards and then considers their relationship and equivalent global objectives. In addition, it presents the methods behind the development of such standards for certification of competence in personnel involved with data collection, modelling and measurements of KPIs. Two case studies are presented that highlight the integrated strategy in practise.

  2. Monitoring the Microgravity Environment Quality On-Board the International Space Station Using Soft Computing Techniques

    Science.gov (United States)

    Jules, Kenol; Lin, Paul P.

    2001-01-01

    This paper presents an artificial intelligence monitoring system developed by the NASA Glenn Principal Investigator Microgravity Services project to help the principal investigator teams identify the primary vibratory disturbance sources that are active, at any moment in time, on-board the International Space Station, which might impact the microgravity environment their experiments are exposed to. From the Principal Investigator Microgravity Services' web site, the principal investigator teams can monitor via a graphical display, in near real time, which event(s) is/are on, such as crew activities, pumps, fans, centrifuges, compressor, crew exercise, platform structural modes, etc., and decide whether or not to run their experiments based on the acceleration environment associated with a specific event. This monitoring system is focused primarily on detecting the vibratory disturbance sources, but could be used as well to detect some of the transient disturbance sources, depending on the events duration. The system has built-in capability to detect both known and unknown vibratory disturbance sources. Several soft computing techniques such as Kohonen's Self-Organizing Feature Map, Learning Vector Quantization, Back-Propagation Neural Networks, and Fuzzy Logic were used to design the system.

  3. The environment, international standards, asset health management and condition monitoring: An integrated strategy

    International Nuclear Information System (INIS)

    Roe, S.; Mba, D.

    2009-01-01

    Asset Health Management (AHM), supported by condition monitoring (CM) and performance measuring technologies, together with trending, modelling and diagnostic frameworks, is not only critical to the reliability of high-value machines, but also to a companies Overall Equipment Efficiency (OEE), system safety and profitability. In addition these protocols are also critical to the global concern of the environment. Industries involved with monitoring key performances indicators (KPI) to improve OEE would benefit from a standardised qualification and certification scheme for their personnel, particularly if it is based on internationally accepted procedures for the various CM technologies that also share the same objectives as AH and CM. Furthermore, the development of 'models' for implementation of a Carbon tax is intrinsically dependent on the integrity and accuracy of measurements contributing to these indicators. This paper reviews the global picture of condition monitoring, the environment and related international standards and then considers their relationship and equivalent global objectives. In addition, it presents the methods behind the development of such standards for certification of competence in personnel involved with data collection, modelling and measurements of KPIs. Two case studies are presented that highlight the integrated strategy in practise

  4. Tunable Diode Laser Sensor for Monitoring and Control of Harsh Combustion Environments

    Energy Technology Data Exchange (ETDEWEB)

    VonDrasek, William; Melsio-Pubill, Anna

    2006-05-30

    This work represents the collaborative effort between American Air Liquide and Physical Sciences, Inc. for developing a sensor based on near-IR tunable diode lasers (TDL). The multi-species capability of the sensor for simultaneous monitoring of CO, O2, and H2O concentration as well as gas temperature is ideal for in-situ monitoring on industrial furnaces. The chemical species targeted are fundamental for controlling the combustion space for improved energy efficiency, reduced pollutants, and improved product quality, when coupling the measurement to a combustion control system. Several add-on modules developed provide flexibility in the system configuration for handling different process monitoring applications. For example, the on-Demand Power Control system for the 1.5 ?m laser is used for high particle density exhaust streams where laser transmission is problematic. For long-distance signal collection a fiber optic communication system is used to reduce noise pick-up. Finally, hardened modules to withstand high ambient temperatures, immune to EMF interference, protection from flying debris, and interfaced with pathlength control laser beam shielding probes were developed specifically for EAF process monitoring. Demonstration of these different system configurations was conducted on Charter Steel's reheat furnace, Imco Recycling, Inc. (now Aleris International, Inc.) aluminum reverberatory furnace, and Gerdau Ameristeel's EAF. Measurements on the reheat furnace demonstrated zone monitoring with the measurement performed close to the steel billet. Results from the aluminum furnace showed the benefit of measuring in-situ near the bath. In this case, low-level furnace optimization was performed and demonstrated 5% fuel savings. Monitoring tests on the EAF off-gas demonstrated the level of industrialization of the sensor to survive the harsh EAF environment. Long-term testing on the EAF has been on-going for over 6 months with essentially zero maintenance

  5. Norwegian monitoring (1990-2015) of the marine environment around the sunken nuclear submarine Komsomolets.

    Science.gov (United States)

    Gwynn, Justin P; Heldal, Hilde Elise; Flo, Janita K; Sværen, Ingrid; Gäfvert, Torbjörn; Haanes, Hallvard; Føyn, Lars; Rudjord, Anne Liv

    2018-02-01

    Norway has monitored the marine environment around the sunken Russian nuclear submarine Komsomolets since 1990. This study presents an overview of 25 years of Norwegian monitoring data (1990-2015). Komsomolets sank in 1989 at a depth of 1680 m in the Norwegian Sea while carrying two nuclear torpedoes in its armament. Subsequent Soviet and Russian expeditions to Komsomolets have shown that releases from the reactor have occurred and that the submarine has suffered considerable damage to its hulls. Norwegian monitoring detected 134 Cs in surface sediments around Komsomolets in 1993 and 1994 and elevated activity concentrations of 137 Cs in bottom seawater between 1991 and 1993. Since then and up to 2015, no increased activity concentrations of radionuclides above values typical for the Norwegian Sea have been observed in any environmental sample collected by Norwegian monitoring. In 2013 and 2015, Norwegian monitoring was carried out using an acoustic transponder on the sampling gear that allowed samples to be collected at precise locations, ∼20 m from the hull of Komsomolets. The observed 238 Pu/ 239,240 Pu activity ratios and 240 Pu/ 239 Pu atom ratios in surface sediments sampled close to Komsomolets in 2013 did not indicate any releases of Pu isotopes from reactor or the torpedo warheads. Rather, these values probably reflect the overprinting of global fallout ratios with fluxes of these Pu isotopes from long-range transport of authorised discharges from nuclear reprocessing facilities in Northern Europe. However, due to the depth at which Komsomolets lies, the collection of seawater and sediment samples in the immediate area around the submarine using traditional sampling techniques from surface vessels is not possible, even with the use of acoustic transponders. Further monitoring is required in order to have a clear understanding of the current status of Komsomolets as a potential source of radioactive contamination to the Norwegian marine environment

  6. Macrobrachium amazonicum: an alternative for microbiological monitoring of aquatic environments in Brazil

    Directory of Open Access Journals (Sweden)

    Raimunda Sâmia Nogueira Brilhante

    2014-11-01

    Full Text Available This study aimed to evaluate the role of the Amazon River prawn, Macrobrachium amazonicum, as carrier of Candida spp., by analyzing the correlation between Candida spp. from these prawns and their environment (surface water and sediment, through M13-PCR fingerprinting and RAPD-PCR. For this purpose, 27 strains of Candida spp. were evaluated. These strains were recovered from the gastrointestinal tract of adult M. amazonicum (7/27 from Catú Lake, Ceará State, Brazil and from the aquatic environment (surface water and sediment of this lake (20/27. Molecular comparison between the strains from prawns and the aquatic environment was conducted by M13-PCR fingerprinting and RAPD-PCR, utilizing the primers M13 and OPQ16, respectively. The molecular analysis revealed similarities between the band patterns of eight Candida isolates with the primer M13 and 11 isolates with the primer OPQ16, indicating that the same strains are present in the digestive tract of M. amazonicum and in the aquatic environment where these prawns inhabit. Therefore, these prawns can be used as sentinels for environmental monitoring through the recovery of Candida spp. from the aquatic environment in their gastrointestinal tract

  7. Development of metallic system multi-composite materials for compound environment and corrosion monitoring technology

    International Nuclear Information System (INIS)

    Kiuchi, Kiyoshi

    1996-01-01

    For the structural materials used for the pressure boundary of nuclear power plants and others, the long term durability over several decades under the compound environment, in which the action of radiation and the corrosion and erosion in the environment of use are superposed, is demanded. To its controlling factors, the secular change of materials due to irradiation ageing and the chemical and physical properties of extreme compound environment are related complicatedly. In the first period of this research, the development of the corrosion-resistant alloys with the most excellent adaptability to environments was carried out by the combination of new alloy design and alloy manufacturing technology. In the second period, in order to heighten the adaptability as the pressure boundary materials between different compound environments, the creation of metallic system multi-composite materials has been advanced. Also corrosion monitoring technique is being developed. The stainless steel for water-cooled reactors, the wear and corrosion-resistant superalloy for reactor core, the corrosion-resistant alloy and the metallic refractory material for reprocessing nitric acid reaction vessels are reported. (K.I.)

  8. Application of thin layer activation technique for monitoring corrosion of carbon steel in hydrocarbon processing environment.

    Science.gov (United States)

    Saxena, R C; Biswal, Jayashree; Pant, H J; Samantray, J S; Sharma, S C; Gupta, A K; Ray, S S

    2018-05-01

    Acidic crude oil transportation and processing in petroleum refining and petrochemical operations cause corrosion in the pipelines and associated components. Corrosion monitoring is invariably required to test and prove operational reliability. Thin Layer Activation (TLA) technique is a nuclear technique used for measurement of corrosion and erosion of materials. The technique involves irradiation of material with high energy ion beam from an accelerator and measurement of loss of radioactivity after the material is subjected to corrosive environment. In the present study, TLA technique has been used to monitor corrosion of carbon steel (CS) in crude oil environment at high temperature. Different CS coupons were irradiated with a 13 MeV proton beam to produce Cobalt-56 radioisotope on the surface of the coupons. The corrosion studies were carried out by subjecting the irradiated coupons to a corrosive environment, i.e, uninhibited straight run gas oil (SRGO) containing known amount of naphthenic acid (NA) at high temperature. The effects of different parameters, such as, concentration of NA, temperature and fluid velocity (rpm) on corrosion behaviour of CS were studied. Copyright © 2018 Elsevier Ltd. All rights reserved.

  9. High frequency monitoring of the coastal marine environment using the MAREL buoy.

    Science.gov (United States)

    Blain, S; Guillou, J; Tréguer, P; Woerther, P; Delauney, L; Follenfant, E; Gontier, O; Hamon, M; Leilde, B; Masson, A; Tartu, C; Vuillemin, R

    2004-06-01

    The MAREL Iroise data buoy provides physico-chemical measurements acquired in surface marine water in continuous and autonomous mode. The water is pumped 1.5 m from below the surface through a sampling pipe and flows through the measuring cell located in the floating structure. Technological innovations implemented inside the measuring cell atop the buoy allow a continuous cleaning of the sensor, while injection of chloride ions into the circuit prevents biological fouling. Specific sensors for temperature, salinity, oxygen and fluorescence investigated in this paper have been evaluated to guarantee measurement precision over a 3 month period. A bi-directional link under Internet TCP-IP protocols is used for data, alarms and remote-control transmissions with the land-based data centre. Herein, we present a 29 month record for 4 parameters measured using a MAREL buoy moored in a coastal environment (Iroise Sea, Brest, France). The accuracy of the data provided by the buoy is assessed by comparison with measurements of sea water weekly sampled at the same site as part of SOMLIT (Service d'Observation du Milieu LIToral), the French network for monitoring of the coastal environment. Some particular events (impact of intensive fresh water discharges, dynamics of a fast phytoplankton bloom) are also presented, demonstrating the worth of monitoring a highly variable environment with a high frequency continuous reliable system.

  10. A Movement-Assisted Deployment of Collaborating Autonomous Sensors for Indoor and Outdoor Environment Monitoring

    Directory of Open Access Journals (Sweden)

    Ewa Niewiadomska-Szynkiewicz

    2016-09-01

    Full Text Available Using mobile robots or unmanned vehicles to assist optimal wireless sensors deployment in a working space can significantly enhance the capability to investigate unknown environments. This paper addresses the issues of the application of numerical optimization and computer simulation techniques to on-line calculation of a wireless sensor network topology for monitoring and tracking purposes. We focus on the design of a self-organizing and collaborative mobile network that enables a continuous data transmission to the data sink (base station and automatically adapts its behavior to changes in the environment to achieve a common goal. The pre-defined and self-configuring approaches to the mobile-based deployment of sensors are compared and discussed. A family of novel algorithms for the optimal placement of mobile wireless devices for permanent monitoring of indoor and outdoor dynamic environments is described. They employ a network connectivity-maintaining mobility model utilizing the concept of the virtual potential function for calculating the motion trajectories of platforms carrying sensors. Their quality and utility have been justified through simulation experiments and are discussed in the final part of the paper.

  11. A Movement-Assisted Deployment of Collaborating Autonomous Sensors for Indoor and Outdoor Environment Monitoring.

    Science.gov (United States)

    Niewiadomska-Szynkiewicz, Ewa; Sikora, Andrzej; Marks, Michał

    2016-09-14

    Using mobile robots or unmanned vehicles to assist optimal wireless sensors deployment in a working space can significantly enhance the capability to investigate unknown environments. This paper addresses the issues of the application of numerical optimization and computer simulation techniques to on-line calculation of a wireless sensor network topology for monitoring and tracking purposes. We focus on the design of a self-organizing and collaborative mobile network that enables a continuous data transmission to the data sink (base station) and automatically adapts its behavior to changes in the environment to achieve a common goal. The pre-defined and self-configuring approaches to the mobile-based deployment of sensors are compared and discussed. A family of novel algorithms for the optimal placement of mobile wireless devices for permanent monitoring of indoor and outdoor dynamic environments is described. They employ a network connectivity-maintaining mobility model utilizing the concept of the virtual potential function for calculating the motion trajectories of platforms carrying sensors. Their quality and utility have been justified through simulation experiments and are discussed in the final part of the paper.

  12. Multi-terminal remote monitoring and warning system using Micro Air Vehicle for dangerous environment

    Science.gov (United States)

    Yu, Yanan; Wang, Xiaoxun; He, Chengcheng; Lai, Chenlong; Liu, Yuanchao

    2015-11-01

    For overcoming the problems such as remote operation and dangerous tasks, multi-terminal remote monitoring and warning system based on STC89C52 Micro Control Unit and wireless communication technique was proposed. The system with MCU as its core adopted multiple sets of sensor device to monitor environment parameters of different locations, such as temperature, humidity, smoke other harmful gas concentration. Data information collected was transmitted remotely by wireless transceiver module, and then multi-channel data parameter was processed and displayed through serial communication protocol between the module and PC. The results of system could be checked in the form of web pages within a local network which plays a wireless monitoring and warning role. In a remote operation, four-rotor micro air vehicle which fixed airborne data acquisition device was utilized as a middleware between collecting terminal and PC to increase monitoring scope. Whole test system has characteristics of simple construction, convenience, real time ability and high reliability, which could meet the requirements of actual use.

  13. A Wearable Wireless Sensor Network for Indoor Smart Environment Monitoring in Safety Applications.

    Science.gov (United States)

    Antolín, Diego; Medrano, Nicolás; Calvo, Belén; Pérez, Francisco

    2017-02-14

    This paper presents the implementation of a wearable wireless sensor network aimed at monitoring harmful gases in industrial environments. The proposed solution is based on a customized wearable sensor node using a low-power low-rate wireless personal area network (LR-WPAN) communications protocol, which as a first approach measures CO₂ concentration, and employs different low power strategies for appropriate energy handling which is essential to achieving long battery life. These wearables nodes are connected to a deployed static network and a web-based application allows data storage, remote control and monitoring of the complete network. Therefore, a complete and versatile remote web application with a locally implemented decision-making system is accomplished, which allows early detection of hazardous situations for exposed workers.

  14. A Wearable Wireless Sensor Network for Indoor Smart Environment Monitoring in Safety Applications

    Directory of Open Access Journals (Sweden)

    Diego Antolín

    2017-02-01

    Full Text Available This paper presents the implementation of a wearable wireless sensor network aimed at monitoring harmful gases in industrial environments. The proposed solution is based on a customized wearable sensor node using a low-power low-rate wireless personal area network (LR-WPAN communications protocol, which as a first approach measures CO2 concentration, and employs different low power strategies for appropriate energy handling which is essential to achieving long battery life. These wearables nodes are connected to a deployed static network and a web-based application allows data storage, remote control and monitoring of the complete network. Therefore, a complete and versatile remote web application with a locally implemented decision-making system is accomplished, which allows early detection of hazardous situations for exposed workers.

  15. Passive Sampling in Regulatory Chemical Monitoring of Nonpolar Organic Compounds in the Aquatic Environment

    DEFF Research Database (Denmark)

    Booij, Kees; Robinson, Craig D; Burgess, Robert M

    2016-01-01

    We reviewed compliance monitoring requirements in the European Union, the United States, and the Oslo-Paris Convention for the protection of the marine environment of the North-East Atlantic, and evaluated if these are met by passive sampling methods for nonpolar compounds. The strengths...... is the best available technology for chemical monitoring of nonpolar organic compounds. Key issues to be addressed by scientists and environmental managers are outlined....... and shortcomings of passive sampling are assessed for water, sediments, and biota. Passive water sampling is a suitable technique for measuring concentrations of freely dissolved compounds. This method yields results that are incompatible with the EU's quality standard definition in terms of total concentrations...

  16. Qualification, monitoring, and integration into a production environment of the world's first fully programmable illuminator

    Science.gov (United States)

    McIntyre, Gregory; Corliss, Daniel; Groenendijk, Remco; Carpaij, Rene; van Niftrik, Ton; Landie, Guillaume; Tamura, Takao; Pepin, Thomas; Waddell, James; Woods, Jerry; Robinson, Chris; Tian, Kehan; Johnson, Richard; Halle, Scott; Kim, Ryoung-Han; Mclellan, Erin; Kato, Hirokazu; Scaduto, Anthony; Maier, Carl; Colburn, Matt

    2011-04-01

    This paper will describe the development, qualification, monitoring, and integration into a production environment of the world's first fully programmable illuminator for optical lithography. FlexRay TM, a programmable illuminator based on a MEMs multi-mirror array that was developed for TWINSCAN XT:19x0i and TWINSCAN NXT series ASML immersion scanners, was first installed in January 2010 at Albany Nanotech, with subsequent tools installed in IBM's East Fishkill Manufacturing facility. After a brief overview of the concept and benefits of FlexRay, this paper will provide a comprehensive assessment of its reliability and imaging performance. A CD-based pupil qualification (CDPQ) procedure will be introduced and shown to be an efficient and effective way to monitor pupil performance. Various CDPQ and in-resist measurement results will be described, offering convincing evidence that FlexRay reliably generates high-quality pupils and is well suited for high volume manufacturing at lithography's leading edge.

  17. Research-Based Monitoring, Prediction, and Analysis Tools of the Spacecraft Charging Environment for Spacecraft Users

    Science.gov (United States)

    Zheng, Yihua; Kuznetsova, Maria M.; Pulkkinen, Antti A.; Maddox, Marlo M.; Mays, Mona Leila

    2015-01-01

    The Space Weather Research Center (http://swrc. gsfc.nasa.gov) at NASA Goddard, part of the Community Coordinated Modeling Center (http://ccmc.gsfc.nasa.gov), is committed to providing research-based forecasts and notifications to address NASA's space weather needs, in addition to its critical role in space weather education. It provides a host of services including spacecraft anomaly resolution, historical impact analysis, real-time monitoring and forecasting, tailored space weather alerts and products, and weekly summaries and reports. In this paper, we focus on how (near) real-time data (both in space and on ground), in combination with modeling capabilities and an innovative dissemination system called the integrated Space Weather Analysis system (http://iswa.gsfc.nasa.gov), enable monitoring, analyzing, and predicting the spacecraft charging environment for spacecraft users. Relevant tools and resources are discussed.

  18. The monitoring of the terrestrial environment around Almirante Alvaro Alberto nuclear power station

    Energy Technology Data Exchange (ETDEWEB)

    Tavares, P.G.; Souza, R.F.; Cardoso, S.N.M., E-mail: pgtares@eletronuclear.gov.b, E-mail: rfsouza@eletronuclear.gov.b, E-mail: sergion@eletronuclear.gov.b [ELETROBRAS Eletronuclear S.A., Paraty, RJ (Brazil). Lab. de Monitoracao Ambiental

    2011-07-01

    The goal of this paper is to evaluate the environmental monitoring around Almirante Alvaro Alberto Nuclear Power Station after the beginning the operation of Unit II, in July 2000. The Environmental Monitoring Laboratory (EML) has, for purpose, to monitor the environment around the station to verify if there is a potential impact caused by the operation of the units. The EML collects several environmental samples and analyses radiometrically to determine the presence of artificial radionuclides. The types of the samples are marine samples (sea water, fish, algae, beach sand and sediments), terrestrial (milk, banana, soil, grass, superficial and underground water and river water and sediment) and aerial samples (rain water, airborne for iodine and particulate). This paper only describes the monitoring of terrestrial samples. At the EML, the samples are prepared and analysed following international procedures. The samples of milk, banana, soil, grass, surface and underground water, river water and river sediment are analysed by gamma spectrometry in a multi-channel analyser GENIE-2000 System with High-purity Germanium (HpGe) detectors to determine the activities of the detectable radionuclides. The EML also analyses tritium in surface water by liquid scintillation counting. In addition, analysis of {sup 89}Sr/{sup 90}Sr, by beta counting and {sup 131}I by gamma spectrometry are performed in the processed milk. The results are, then, compared with those obtained in pre-operational time of Angra 1 (1978 - 1982) and those obtained in operational time of the units until 2010. The results show us that, from 1982 until now, there is no impact in terrestrial environment caused by the operation neither of Angra 1 nor both Angra 1 and Angra 2. (author)

  19. The monitoring of the terrestrial environment around Almirante Alvaro Alberto nuclear power station

    International Nuclear Information System (INIS)

    Tavares, P.G.; Souza, R.F.; Cardoso, S.N.M.

    2011-01-01

    The goal of this paper is to evaluate the environmental monitoring around Almirante Alvaro Alberto Nuclear Power Station after the beginning the operation of Unit II, in July 2000. The Environmental Monitoring Laboratory (EML) has, for purpose, to monitor the environment around the station to verify if there is a potential impact caused by the operation of the units. The EML collects several environmental samples and analyses radiometrically to determine the presence of artificial radionuclides. The types of the samples are marine samples (sea water, fish, algae, beach sand and sediments), terrestrial (milk, banana, soil, grass, superficial and underground water and river water and sediment) and aerial samples (rain water, airborne for iodine and particulate). This paper only describes the monitoring of terrestrial samples. At the EML, the samples are prepared and analysed following international procedures. The samples of milk, banana, soil, grass, surface and underground water, river water and river sediment are analysed by gamma spectrometry in a multi-channel analyser GENIE-2000 System with High-purity Germanium (HpGe) detectors to determine the activities of the detectable radionuclides. The EML also analyses tritium in surface water by liquid scintillation counting. In addition, analysis of 89 Sr/ 9 0 Sr, by beta counting and 131 I by gamma spectrometry are performed in the processed milk. The results are, then, compared with those obtained in pre-operational time of Angra 1 (1978 - 1982) and those obtained in operational time of the units until 2010. The results show us that, from 1982 until now, there is no impact in terrestrial environment caused by the operation neither of Angra 1 nor both Angra 1 and Angra 2. (author)

  20. Supervision monitoring for radiation environment around Daya Bay and Lingao nuclear power stations

    International Nuclear Information System (INIS)

    Huang Naiming; Chen Zhidong; Song Haiqing; Deng Fei; Lin Qing; Huang Nairong; Zhou Ruidong; Mo Guanghua; Li Lingjuan; Liu Ying; Li Qiaoqin; Lai Liming; Zhou Xue

    2004-01-01

    This paper systematically introduces the supervision monitoring for radiation environment around the Guangdong Daya Bay and Ling Ao nuclear power station by the Guangdong Environmental Radiation Research and Monitoring Center. It includes the monitoring plan, methods, quality assurance, main results and conclusions. The results show that: (1) The gas discharge have not caused any detectable impacts to the terrestrial and atmospheric environment since their operation; (2) 110m Ag could only be detected in seawater in the West Daya Bay in 1995 and 1997 and in sediments in 1997. The maximum annual average in seawater was 3.1 Bq/m 3 , annual average of 110m Ag in sediments was 1.0 Bq/kg(dry). But it was always detectable in pearl oyster, gulfweed and cuttlefish in the West Daya Bay. The 110m Ag concentrations in halobios were relatively higher in 1994, 1996 and 1997. The maximum concentrations in pearl oyster, gulfweed and cuttlefish were 2.2, 1.7 and 5.8 Bq/kg (fresh) respectively. It has significantly decreased with decreasing discharge from the stations since 1997. (3) 137 Cs could be detected in almost all seawater samples in the West Daya Bay and the concentration were relatively higher from 1994-1998. The maximum annual average was laid in 1995 and it was 4.6 Bq/m 3 . After 1999, its concentration ranged in the background level. The concentrations in other marine samples were extremely low and changed in the range of the background. (4) 3 H in seawater in the West Daya Bay would go up as a pulse soon after 3 H discharge from the station and would go down to the background after 3-5 days. The annual average of monitoring results were between 0.8-3.4 Bq/L

  1. Novel biospectroscopy sensor technologies towards environmental health monitoring in urban environments

    International Nuclear Information System (INIS)

    Obinaju, Blessing E.; Martin, Francis L.

    2013-01-01

    Biospectroscopy is an emerging inter-disciplinary field that exploits the application of sensor technologies [e.g., Fourier-transform infrared spectroscopy, Raman spectroscopy] to lend novel insights into biological questions. Methods involved are relatively non-destructive so samples can subsequently be analysed by more conventional approaches, facilitating deeper mechanistic insights. Fingerprint spectra are derived and these consist of wavenumber–absorbance intensities; within a typical biological experiment, a complex dataset is quickly generated. Biological samples range from biofluids to cytology to tissues derived from human or sentinel sources, and analyses can be carried out ex vivo or in situ in living tissue. A reference range of a designated normal state can be derived; anything outside this is potentially atypical and discriminating chemical entities identified. Computational approaches allow one to minimize within-category confounding factors. Because of ease of sample preparation, low-cost and high-throughput capability, biospectroscopy approaches herald a new greener means of environmental health monitoring in urban environments. -- Highlights: ► Biospectroscopy is an emerging inter-disciplinary field. ► Physical sciences sensors with computational tools lend novel insights into biology. ► Analyse in a non-destructive manner; correlate with conventional methodologies. ► Low-cost, high-throughput and label-free (i.e., a green) technology. ► Can be applied to environmental health monitoring in urban environments. -- Biospectroscopy techniques allow the fingerprinting of biological material in a wide range of contexts that could relate to environmental health monitoring in urban environments

  2. IMAGE information monitoring and applied graphics software environment. Volume 4. Applications description

    International Nuclear Information System (INIS)

    Hallam, J.W.; Ng, K.B.; Upham, G.L.

    1986-09-01

    The EPRI Information Monitoring and Applied Graphics Environment (IMAGE) system is designed for 'fast proto-typing' of advanced concepts for computer-aided plant operations tools. It is a flexible software system which can be used for rapidly creating, dynamically driving and evaluating advanced operator aid displays. The software is written to be both host computer and graphic device independent. This four volume report includes an Executive Overview of the IMAGE package (Volume 1), followed by Software Description (Volume II), User's Guide (Volume III), and Description of Example Applications (Volume IV)

  3. Development of Advanced In-Situ Techniques for Chemistry Monitoring and Corrosion Mitigation in SCWO Environments

    International Nuclear Information System (INIS)

    Macdonald, D.D.

    2000-01-01

    Super Critical Water Oxidation (SCWO) is a promising technology for destroying highly toxic organic waste (including physiological agents) and for reducing the volume of DOE's low-level nuclear waste. The major problem inhibiting the wide implementation of SCWO is the lack of fundamental knowledge about various physico-chemical and corrosion processes that occur in SCW environments. In particular, the lack of experimental techniques for accurately monitoring important parameters, such as pH, corrosion potential and corrosion rate, has severely hampered the development of a quantitative understanding of the degradation of materials in this extraordinarily aggressive environment. Accordingly, the principal objective of the present program has been to develop new, innovative methods for accurately measuring parameters that characterize corrosion processes under super critical conditions

  4. Robot Vision to Monitor Structures in Invisible Fog Environments Using Active Imaging Technology

    Energy Technology Data Exchange (ETDEWEB)

    Park, Seungkyu; Park, Nakkyu; Baik, Sunghoon; Choi, Youngsoo; Jeong, Kyungmin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    Active vision is a direct visualization technique using a highly sensitive image sensor and a high intensity illuminant. Range-gated imaging (RGI) technique providing 2D and 3D images is one of emerging active vision technologies. The RGI technique extracts vision information by summing time sliced vision images. In the RGI system, objects are illuminated for ultra-short time by a high intensity illuminant and then the light reflected from objects is captured by a highly sensitive image sensor with the exposure of ultra-short time. The RGI system provides 2D and 3D image data from several images and it moreover provides clear images from invisible fog and smoke environment by using summing of time-sliced images. Nowadays, the Range-gated (RG) imaging is an emerging technology in the field of surveillance for security applications, especially in the visualization of invisible night and fog environment. Although RGI viewing was discovered in the 1960's, this technology is, nowadays, more and more applicable by virtue of the rapid development of optical and sensor technologies, such as highly sensitive imaging sensor and ultra-short pulse laser light. In contrast to passive vision systems, this technology enables operation even in harsh environments like fog and smoke. During the past decades, several applications of this technology have been applied in target recognition and in harsh environments, such as fog, underwater vision. Also, this technology has been demonstrated 3D imaging based on range-gated imaging. In this paper, a robot system to monitor structures in invisible fog environment is developed using an active range-gated imaging technique. The system consists of an ultra-short pulse laser device and a highly sensitive imaging sensor. The developed vision system is carried out to monitor objects in invisible fog environment. The experimental result of this newly approach vision system is described in this paper. To see invisible objects in fog

  5. Robot Vision to Monitor Structures in Invisible Fog Environments Using Active Imaging Technology

    International Nuclear Information System (INIS)

    Park, Seungkyu; Park, Nakkyu; Baik, Sunghoon; Choi, Youngsoo; Jeong, Kyungmin

    2014-01-01

    Active vision is a direct visualization technique using a highly sensitive image sensor and a high intensity illuminant. Range-gated imaging (RGI) technique providing 2D and 3D images is one of emerging active vision technologies. The RGI technique extracts vision information by summing time sliced vision images. In the RGI system, objects are illuminated for ultra-short time by a high intensity illuminant and then the light reflected from objects is captured by a highly sensitive image sensor with the exposure of ultra-short time. The RGI system provides 2D and 3D image data from several images and it moreover provides clear images from invisible fog and smoke environment by using summing of time-sliced images. Nowadays, the Range-gated (RG) imaging is an emerging technology in the field of surveillance for security applications, especially in the visualization of invisible night and fog environment. Although RGI viewing was discovered in the 1960's, this technology is, nowadays, more and more applicable by virtue of the rapid development of optical and sensor technologies, such as highly sensitive imaging sensor and ultra-short pulse laser light. In contrast to passive vision systems, this technology enables operation even in harsh environments like fog and smoke. During the past decades, several applications of this technology have been applied in target recognition and in harsh environments, such as fog, underwater vision. Also, this technology has been demonstrated 3D imaging based on range-gated imaging. In this paper, a robot system to monitor structures in invisible fog environment is developed using an active range-gated imaging technique. The system consists of an ultra-short pulse laser device and a highly sensitive imaging sensor. The developed vision system is carried out to monitor objects in invisible fog environment. The experimental result of this newly approach vision system is described in this paper. To see invisible objects in fog

  6. SEM: A Cultural Change Agent

    Science.gov (United States)

    Barnes, Bradley; Bourke, Brian

    2015-01-01

    The authors advance the concept that institutional culture is a purposeful framework by which to view SEM's utility, particularly as a cultural change agent. Through the connection of seemingly independent functions of performance and behavior, implications emerge that deepen the understanding of the influence of culture on performance outcomes…

  7. NATO Advanced Research Workshop, 19-22 May 1997: Rapid Method for Monitoring the Environment for Biological Hazards

    National Research Council Canada - National Science Library

    1997-01-01

    The NATO Advanced Research Workshop met for the purpose of bringing to light rapid methods for monitoring the environment for biological hazards such as biological warfare agents, naturally occurring...

  8. Independent regulatory control and monitoring of the environment at the uranium legacy sites under reclamation

    International Nuclear Information System (INIS)

    Shandala, N.K.; Titov, A.V.; Kiselev, S.M.; Isaev, D.V.; Aladova, R.A.

    2012-01-01

    Full text: Radiation safety at areas affected by the natural uranium mining and milling facilities is very important for the environment protection and human health. For this purpose the close operator-regulator contact is required during remedial operations. One of the key mechanisms of the operating regulatory supervision of radiation safety at uranium legacy sites is organization of independent radiation control and monitoring in the course of reclamation and after its completion. The main stages of this strategy include: detailed radiation survey at the area and in the vicinity of the former uranium mining sites; threat assessment in order to identify the regulatory priorities; environmental radiation control and monitoring. Tailings and shallow disposal sites of the uranium mining wastes are the most critical areas in terms of potential hazard for the environment. Tailings are the source of contamination of the near-land air due to the radionuclide dust resuspension from the tailing surface; surface and ground water due to washing out from by precipitation and surface streams of toxic and radioactive elements. Frequently, contamination of surface and ground waters results in some problems, especially when using the leaching fluids for the solution mining and draining hydraulic fluids. Radiation risk for the residents of areas near not operating uranium mining and milling facilities depends on the following factors: radon exhalation from the surface of dumps and tailing; radioactive dust transfer; using radioactive material in building; contamination of surface water streams and aquifers used for drinking water supply; contamination of open ponds used for fish breeding and catching; contamination of foodstuffs grown in the nuclear legacy areas. Radiation monitoring is necessary for the up-to-date response to changing radiation situation during reclamation and arrangement of adequate countermeasures. We mean here comprehensive dynamic surveillance including long

  9. Overview of the Copernicus Marine Environment Monitoring Service Products Available for the Arctic Region

    Directory of Open Access Journals (Sweden)

    A.L. Kholod

    2017-04-01

    Full Text Available The Copernicus Marine Environment Monitoring Service is one of six services (ocean, atmosphere, land, emergency situations, security and climate changes launched by the European Union within the EU Earth observation program. The data in the monitoring system covers both the entire World Ocean and individual European basins. The paper reviews the products of the Copernicus Marine Service operational system available in the Arctic. At the present time this region is of the increased interest both in Russia and in the world community. The system products include information on the thermodynamic, biogeochemical and bio-optical state of the marine environment. The system products are accessed through the electronic catalog of products. Selection criteria and possibilities for searching interesting information through the interactive web-portal are given in the paper. The system products containing the data of model calculations, satellite and in situ measurement results are considered. Spatial and temporal characteristics of the products are given, information on by whom, how the product was obtained and what is its accuracy is represented. The results of the system products visualization by the integrated tools (they allow one to construct and analyze time series, profiles, horizontal and vertical sections are shown. All the system data is publicly available to the registered users. Regular changes and updates of the system products as well as the mechanisms for accessing them take place. This information is sent to users by e-mail and is available on the news flash of the web-portal.

  10. An IoT-Based Computational Framework for Healthcare Monitoring in Mobile Environments

    Directory of Open Access Journals (Sweden)

    Higinio Mora

    2017-10-01

    Full Text Available The new Internet of Things paradigm allows for small devices with sensing, processing and communication capabilities to be designed, which enable the development of sensors, embedded devices and other ‘things’ ready to understand the environment. In this paper, a distributed framework based on the internet of things paradigm is proposed for monitoring human biomedical signals in activities involving physical exertion. The main advantages and novelties of the proposed system is the flexibility in computing the health application by using resources from available devices inside the body area network of the user. This proposed framework can be applied to other mobile environments, especially those where intensive data acquisition and high processing needs take place. Finally, we present a case study in order to validate our proposal that consists in monitoring footballers’ heart rates during a football match. The real-time data acquired by these devices presents a clear social objective of being able to predict not only situations of sudden death but also possible injuries.

  11. Effective radiological contamination control and monitoring techniques in high alpha environments.

    Science.gov (United States)

    Funke, Kevin C

    2003-02-01

    In the decommissioning of a highly contaminated alpha environment, such as the one at Hanford's 233-S Plutonium Concentration Facility, one of the key elements of a successful radiological control program is an integrated safety approach. This approach begins with the job-planning phase where the scope of the work is described. This is followed by a brainstorming session involving engineering and craft to identify how to perform the work in a logical sequence of events. Once the brainstorming session is over, a Job Hazard Analysis is performed to identify any potential problems. Mockups are utilized to enable the craft to get hands on experience and provide feedback and ideas to make the job run smoother. Ideas and experience gained during mockups are incorporated into the task instruction. To assure appropriate data are used in planning and executing the job, our principal evaluation tools included lapel and workplace air sampling, plus continuous air monitors and frequent surveys to effectively monitor job progress. In this highly contaminated alpha environment, with contamination levels ranging from 0.3 Bq cm-2 to approximately 100,000 Bq cm-2 (2,000 dpm per 100 cm2 to approximately 600 million dpm per 100 cm2), with average working levels of 1,600-3,200 Bq cm-2 (10-20 million dpm per 100 cm2) without concomitant ambient radiation levels, control of the spread of contamination is key to keeping airborne levels As Low As Reasonably Achievable.

  12. External radiation monitoring in TAPS and RAPS environs (1980-81) using TLD

    International Nuclear Information System (INIS)

    Basu, A.S.; Nambi, K.S.V.; Sunta, C.M.

    1983-01-01

    Results of environmental external radiation monitoring using quarterly integrated TLD measurements are presented for environments of the Tarapur Atomic Power Station (TAPS) and the Rajasthan Atomic Power Station (RAPS) for the two year monitoring period (1980-81). The data fit into the unimodal log-normal distribution except for locations where gaseous radioactivity escaping from the plant makes a significant contribution. The average natural radiation background in TAPS and RAPS environment is estimated to be 59.6 +- 4.7 mR yr -1 and 65.1 +- 9.8 mR yr -1 respectively. Contribution from the plant superimposed over the natural level leads frequently to bi-normal distribution. The effect of stack-released gaseous radioactivity is seen in locations within 1.6 km of TAPS: for example Ghivoli village registered an excess of 9.3 mR yr -1 over the natural background. The quarterly background values indicate minor temporal and spatial variations which can be attributed to changes in natural as well as stack released radioactivity. (author)

  13. An IoT-Based Computational Framework for Healthcare Monitoring in Mobile Environments.

    Science.gov (United States)

    Mora, Higinio; Gil, David; Terol, Rafael Muñoz; Azorín, Jorge; Szymanski, Julian

    2017-10-10

    The new Internet of Things paradigm allows for small devices with sensing, processing and communication capabilities to be designed, which enable the development of sensors, embedded devices and other 'things' ready to understand the environment. In this paper, a distributed framework based on the internet of things paradigm is proposed for monitoring human biomedical signals in activities involving physical exertion. The main advantages and novelties of the proposed system is the flexibility in computing the health application by using resources from available devices inside the body area network of the user. This proposed framework can be applied to other mobile environments, especially those where intensive data acquisition and high processing needs take place. Finally, we present a case study in order to validate our proposal that consists in monitoring footballers' heart rates during a football match. The real-time data acquired by these devices presents a clear social objective of being able to predict not only situations of sudden death but also possible injuries.

  14. A self-sustainable winery, an advanced passive building and remote monitoring of environments in wineries

    Directory of Open Access Journals (Sweden)

    Roger Boulton

    2017-08-01

    Full Text Available The self-sustainable winery was conceived in 2006 and the intention was to create a building and its related utility systems that would operate independently from the energy and water grids and to eliminate hydrocarbon fuels from its operation, capture and sequester the carbon dioxide from its fermentations and create a zero carbon footprint facility. The winery was the highest scoring LEED building at any university when it was completed and the first LEED Platinum Winery in the USA. The adjacent Jess Jackson sustainable winery building is a highly passive research and utility space that will house the advanced energy and water systems that make this off-grid performance possible. Together these buildings will operate every daily in energy and water positive modes and at capacities, which exceed the demands even during the harvest season. The data system incorporated into these buildings for one hundred and fifty research fermentors, fourteen teaching fermentors will also monitor all energy, water and building activities in a secure, cloud-based software system that supports both web and handheld access, with the potential for bidirectional date and control functions. This data network has been extended to include real time monitoring of temperature, humidity, carbon dioxide and volatile organic compounds in five production areas within two commercial winery sites and two creamery facilities, located more than 100 km from Davis. This now provides an example of a distributed dynamic network for the monitoring of the built environment in remote commercial food and wine facilities.

  15. Demonstration of TEG-powered wireless autonomous transducer solution for condition monitoring in industrial environment

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Ziyang; Patrascu, Mihai; Su, Jiale; Vullers, Ruud J.M. [imec the Netherlands, Eindhoven (Netherlands)

    2011-07-01

    Imec/Holst Centre focuses on the development of wireless autonomous transducer solution, which is poised to bring about huge impact in the sectors of health care, machinery, transportation and energy, etc. In this paper, we first showcase a TEG-powered demonstration for condition monitoring in industrial environment. Composing of sensor-actuator, front-end interface, digital signal processing unit and radio, the developed wireless sensor node can monitor the changing operating condition, i.e. the loading on a rolling-element bearing, on a rotating shaft. The use of a specially designed TEG, working in tandem with an energy storage device, can significantly improve the energy autonomy of the condition monitoring system as a whole. The different components in the demonstration are presented. Subsequently, the experimental results of vibration signature analysis are exhibited. On one hand, the presented demonstration sheds light on the huge potential of thermoelectric energy harvesting to achieve energy autonomy. On the other hand, it also points to the aspects that are in need of further development, namely miniaturization and cost reduction of energy harvesters. Aimed at the delivery of cost-effective miniaturized thermoelectric harvesting devices, imec/Holst Centre has been tackling with the relevant challenges by resorting to, but not limited to, its expertise in micromachining. An update on the latest research results is subsequently given with regard to various micromachined thermoelectric devices, fully fledged wearable TEGs with custom designed package and thermoelectric material property optimization. (orig.)

  16. A Java based environment to control and monitor distributed processing systems

    International Nuclear Information System (INIS)

    Legrand, I.C.

    1997-01-01

    Distributed processing systems are considered to solve the challenging requirements of triggering and data acquisition systems for future HEP experiments. The aim of this work is to present a software environment to control and monitor large scale parallel processing systems based on a distributed client-server approach developed in Java. One server task may control several processing nodes, switching elements or controllers for different sub-systems. Servers are designed as multi-thread applications for efficient communications with other objects. Servers communicate between themselves by using Remote Method Invocation (RMI) in a peer-to-peer mechanism. This distributed server layer has to provide a dynamic and transparent access from any client to all the resources in the system. The graphical user interface programs, which are platform independent, may be transferred to any client via the http protocol. In this scheme the control and monitor tasks are distributed among servers and network controls the flow of information among servers and clients providing a flexible mechanism for monitoring and controlling large heterogenous distributed systems. (author)

  17. Monitoring User-Based Accessibility Assessment in Urban Environments and in Public Buildings

    Directory of Open Access Journals (Sweden)

    Gintaras Stauskis

    2018-04-01

    Full Text Available The research features analysis of user-experience-based accessibility assessment and progress monitoring of buildings and public spaces; this analysis is used as a tool for facilitating the development of humane, socially sustainable and an inclusive urban environment. A group of users representing people with different kinds of disabilities, the elderly and families with children was created to assess the quality of access to various buildings with different functions and locations across Vilnius and in Singapore. A school, two hospitals, a rehab centre and two offices were selected for access monitoring in Vilnius City, while a hotel, a café and two metro stations with public squares were chosen for access assessment in Singapore. As the same method was principally applied to assess accessibility of selected buildings in Vilnius City in 2000 and 2017 and in Singapore in 2012, the article draws a comparative analysis of access levels in these two cities located in different global regions. The results show a definite improvement of access quality over time and also identify the critical aspects in this process. The segment of plot planning represents the lowest quality of access for all assessed building types as compared to the building segment and the external–internal element segments. The paper also draws conclusions that access improvement is a continuous process of implementing advanced urban policy instruments, and city planners can contribute to it by constantly analysing and presenting to public the monitoring data about the progress in access improvement. Comparing the assessment results between Vilnius City and Singapore – cities that are located in different global regions and in different socio-economic environments – provides a practical tool for benchmarking and setting the priorities for this process.

  18. An Environment for Guideline-based Decision Support Systems for Outpatients Monitoring.

    Science.gov (United States)

    Zini, Elisa M; Lanzola, Giordano; Bossi, Paolo; Quaglini, Silvana

    2017-08-11

    We propose an architecture for monitoring outpatients that relies on mobile technologies for acquiring data. The goal is to better control the onset of possible side effects between the scheduled visits at the clinic. We analyze the architectural components required to ensure a high level of abstraction from data. Clinical practice guidelines were formalized with Alium, an authoring tool based on the PROforma language, using SNOMED-CT as a terminology standard. The Alium engine is accessible through a set of APIs that may be leveraged for implementing an application based on standard web technologies to be used by doctors at the clinic. Data sent by patients using mobile devices need to be complemented with those already available in the Electronic Health Record to generate personalized recommendations. Thus a middleware pursuing data abstraction is required. To comply with current standards, we adopted the HL7 Virtual Medical Record for Clinical Decision Support Logical Model, Release 2. The developed architecture for monitoring outpatients includes: (1) a guideline-based Decision Support System accessible through a web application that helps the doctors with prevention, diagnosis and treatment of therapy side effects; (2) an application for mobile devices, which allows patients to regularly send data to the clinic. In order to tailor the monitoring procedures to the specific patient, the Decision Support System also helps physicians with the configuration of the mobile application, suggesting the data to be collected and the associated collection frequency that may change over time, according to the individual patient's conditions. A proof of concept has been developed with a system for monitoring the side effects of chemo-radiotherapy in head and neck cancer patients. Our environment introduces two main innovation elements with respect to similar works available in the literature. First, in order to meet the specific patients' needs, in our work the Decision

  19. A Cost Effective Solution for Development Environment for Data Acquisition, Monitoring and Simulation of PLC Controlled Applications

    Directory of Open Access Journals (Sweden)

    O. Bjelica

    2014-06-01

    Full Text Available It is very important to test and monitor the operation of Programmable Logic Controller (PLC in real time (online. Nowadays, conventional, but expensive monitoring systems for PLCs, such as Supervisory Control and Data Acquisition (SCADA systems, software and hardware simulators (or debuggers, are widely used. This paper proposes a user friendly and cost-effective development environment for monitoring, data acquisition and online simulation of applications with PLC. The purpose of this solution is to simulate the process which is controlled by the PLC. The performances of the proposed development environment are presented on the examples of washing machine and dishwasher simulators.

  20. Framework for SEM contour analysis

    Science.gov (United States)

    Schneider, L.; Farys, V.; Serret, E.; Fenouillet-Beranger, C.

    2017-03-01

    SEM images provide valuable information about patterning capability. Geometrical properties such as Critical Dimension (CD) can be extracted from them and are used to calibrate OPC models, thus making OPC more robust and reliable. However, there is currently a shortage of appropriate metrology tools to inspect complex two-dimensional patterns in the same way as one would work with simple one-dimensional patterns. In this article we present a full framework for the analysis of SEM images. It has been proven to be fast, reliable and robust for every type of structure, and particularly for two-dimensional structures. To achieve this result, several innovative solutions have been developed and will be presented in the following pages. Firstly, we will present a new noise filter which is used to reduce noise on SEM images, followed by an efficient topography identifier, and finally we will describe the use of a topological skeleton as a measurement tool that can extend CD measurements on all kinds of patterns.

  1. SEM-based characterization techniques

    International Nuclear Information System (INIS)

    Russell, P.E.

    1986-01-01

    The scanning electron microscope is now a common instrument in materials characterization laboratories. The basic role of the SEM as a topographic imaging system has steadily been expanding to include a variety of SEM-based analytical techniques. These techniques cover the range of basic semiconductor materials characterization to live-time device characterization of operating LSI or VLSI devices. This paper introduces many of the more commonly used techniques, describes the modifications or additions to a conventional SEM required to utilize the techniques, and gives examples of the use of such techniques. First, the types of signals available from a sample being irradiated by an electron beam are reviewed. Then, where applicable, the type of spectroscopy or microscopy which has evolved to utilize the various signal types are described. This is followed by specific examples of the use of such techniques to solve problems related to semiconductor technology. Techniques emphasized include: x-ray fluorescence spectroscopy, electron beam induced current (EBIC), stroboscopic voltage analysis, cathodoluminescnece and electron beam IC metrology. Current and future trends of some of the these techniques, as related to the semiconductor industry are discussed

  2. Monitoring airborne biotic contaminants in the indoor environment of pig and poultry confinement buildings.

    Science.gov (United States)

    Hong, Pei-Ying; Li, Xiangzhen; Yang, Xufei; Shinkai, Takumi; Zhang, Yuanhui; Wang, Xinlei; Mackie, Roderick I

    2012-06-01

    Given the growing concerns over human and animal health issues related to confined animal feeding operations, an in-depth examination is required to monitor for airborne bacteria and associated antibiotic resistance genes. Our 16S rRNA-based pyrosequencing revealed that the airborne microbial community skewed towards a higher abundance of Firmicutes (> 59.2%) and Bacteroidetes (4.2-31.4%) within the confinement buildings, while the office environment was predominated by Proteobacteria (55.2%). Furthermore, bioaerosols in the confinement buildings were sporadically associated with genera of potential pathogens, and these genera were more frequently observed in the bioaerosols of pig and layer hen confinement than the turkey confinement buildings and office environment. High abundances of tetracycline resistance genes (9.55 × 10(2) to 1.69 × 10(6) copies ng(-1) DNA) were also detected in the bioaerosols sampled from confinement buildings. Bacterial lineages present in the poultry bioaerosols clustered apart from those present in the pig bioaerosols and among the different phases of pig production, suggesting that different livestock as well as production phase were associated with a distinct airborne microbial community. By understanding the diversity of biotic contaminants associated with the different confinement buildings, this study facilitates the implementation of better management strategies to minimize potential health impacts on both livestock and humans working in this environment. © 2012 Society for Applied Microbiology and Blackwell Publishing Ltd.

  3. Fiber Bragg grating sensors in harsh environments: considerations and industrial monitoring applications

    Science.gov (United States)

    Méndez, Alexis

    2017-06-01

    Over the last few years, fiber optic sensors (FOS) have seen an increased acceptance and widespread use in industrial sensing and in structural monitoring in civil, aerospace, marine, oil & gas, composites and other applications. One of the most prevalent types in use today are fiber Bragg grating (FBG) sensors. Historically, FOS have been an attractive solution because of their EM immunity and suitability for use in harsh environments and rugged applications with extreme temperatures, radiation exposure, EM fields, high voltages, water contact, flammable atmospheres, or other hazards. FBG sensors have demonstrated that can operate reliably in many different harsh environment applications but proper type and fabrication process are needed, along with suitable packaging and installation procedure. In this paper, we review the impact that external factors and environmental conditions play on FBG's performance and reliability, and describe the appropriate sensor types and protection requirements suitable for a variety of harsh environment applications in industrial furnaces, cryogenic coolers, nuclear plants, maritime vessels, oil & gas wells, aerospace crafts, automobiles, and others.

  4. CMEMS (Copernicus Marine Environment Monitoring Service) In Situ Thematic Assembly Centre: A service for operational Oceanography

    Science.gov (United States)

    Manzano Muñoz, Fernando; Pouliquen, Sylvie; Petit de la Villeon, Loic; Carval, Thierry; Loubrieu, Thomas; Wedhe, Henning; Sjur Ringheim, Lid; Hammarklint, Thomas; Tamm, Susanne; De Alfonso, Marta; Perivoliotis, Leonidas; Chalkiopoulos, Antonis; Marinova, Veselka; Tintore, Joaquin; Troupin, Charles

    2016-04-01

    Copernicus, previously known as GMES (Global Monitoring for Environment and Security), is the European Programme for the establishment of a European capacity for Earth Observation and Monitoring. Copernicus aims to provide a sustainable service for Ocean Monitoring and Forecasting validated and commissioned by users. From May 2015, the Copernicus Marine Environment Monitoring Service (CMEMS) is working on an operational mode through a contract with services engagement (result is regular data provision). Within CMEMS, the In Situ Thematic Assembly Centre (INSTAC) distributed service integrates in situ data from different sources for operational oceanography needs. CMEMS INSTAC is collecting and carrying out quality control in a homogeneous manner on data from providers outside Copernicus (national and international networks), to fit the needs of internal and external users. CMEMS INSTAC has been organized in 7 regional Dissemination Units (DUs) to rely on the EuroGOOS ROOSes. Each DU aggregates data and metadata provided by a series of Production Units (PUs) acting as an interface for providers. Homogeneity and standardization are key features to ensure coherent and efficient service. All DUs provide data in the OceanSITES NetCDF format 1.2 (based on NetCDF 3.6), which is CF compliant, relies on SeaDataNet vocabularies and is able to handle profile and time-series measurements. All the products, both near real-time (NRT) and multi-year (REP), are available online for every CMEMS registered user through an FTP service. On top of the FTP service, INSTAC products are available through Oceanotron, an open-source data server dedicated to marine observations dissemination. It provides services such as aggregation on spatio-temporal coordinates and observed parameters, and subsetting on observed parameters and metadata. The accuracy of the data is checked on various levels. Quality control procedures are applied for the validity of the data and correctness tests for the

  5. Wireless microwave acoustic sensor system for condition monitoring in power plant environments

    Energy Technology Data Exchange (ETDEWEB)

    Pereira da Cunha, Mauricio [Univ. of Maine, Orno, ME (United States)

    2017-03-30

    This project successfully demonstrated novel wireless microwave acoustic temperature and pressure sensors that can be embedded into equipment and structures located in fossil fuel power plant environments to monitor the condition of components such as steam headers, re-heat lines, water walls, burner tubes, and power turbines. The wireless microwave acoustic sensor technology researched and developed through a collaborative partnership between the University of Maine and Environetix Technologies Corporation can provide a revolutionary impact in the power industry since it is anticipated that the wireless sensors will deliver reliable real-time sensing information in harsh power plant conditions that involve temperatures up to 1100oC and pressures up to 750 psi. The work involved the research and development of novel high temperature harsh environment thin film electrodes, piezoelectric smart microwave acoustic sensing elements, sensor encapsulation materials that were engineered to function over long times up to 1100oC, and a radio-frequency (RF) wireless interrogation electronics unit that are located both inside and outside the high temperature harsh environment. The UMaine / Environetix team have interacted with diverse power plant facilities, and identified as a testbed a local power generation facility, which burns municipal solid waste (MSW), the Penobscot Energy Recovery Company (PERC), Orrington, Maine. In this facility Environetix / UMaine successfully implemented and tested multiple wireless temperature sensor systems within the harsh-environment of the economizer chamber and at the boiler tubes, transferring the developed technology to the power plant environment to perform real-time sensor monitoring experiments under typical operating conditions, as initially targeted in the project. The wireless microwave acoustic sensor technology developed under this project for power plant applications offers several significant advantages including wireless

  6. Continuous Distributed Top-k Monitoring over High-Speed Rail Data Stream in Cloud Computing Environment

    Directory of Open Access Journals (Sweden)

    Hanning Wang

    2013-01-01

    Full Text Available In the environment of cloud computing, real-time mass data about high-speed rail which is based on the intense monitoring of large scale perceived equipment provides strong support for the safety and maintenance of high-speed rail. In this paper, we focus on the Top-k algorithm of continuous distribution based on Multisource distributed data stream for high-speed rail monitoring. Specifically, we formalized Top-k monitoring model of high-speed rail and proposed DTMR that is the Top-k monitoring algorithm with random, continuous, or strictly monotone aggregation functions. The DTMR was proved to be valid by lots of experiments.

  7. Automated CD-SEM metrology for efficient TD and HVM

    Science.gov (United States)

    Starikov, Alexander; Mulapudi, Satya P.

    2008-03-01

    CD-SEM is the metrology tool of choice for patterning process development and production process control. We can make these applications more efficient by extracting more information from each CD-SEM image. This enables direct monitors of key process parameters, such as lithography dose and focus, or predicting the outcome of processing, such as etched dimensions or electrical parameters. Automating CD-SEM recipes at the early stages of process development can accelerate technology characterization, segmentation of variance and process improvements. This leverages the engineering effort, reduces development costs and helps to manage the risks inherent in new technology. Automating CD-SEM for manufacturing enables efficient operations. Novel SEM Alarm Time Indicator (SATI) makes this task manageable. SATI pulls together data mining, trend charting of the key recipe and Operations (OPS) indicators, Pareto of OPS losses and inputs for root cause analysis. This approach proved natural to our FAB personnel. After minimal initial training, we applied new methods in 65nm FLASH manufacture. This resulted in significant lasting improvements of CD-SEM recipe robustness, portability and automation, increased CD-SEM capacity and MT productivity.

  8. Glacial and periglacial environment monitoring in Aosta Valley - Northwestern Italian Alps

    Science.gov (United States)

    Motta, Elena; Cremonese, Edoardo; Morra di Cella, Umberto; Pogliotti, Paolo; Vagliasindi, Marco

    2010-05-01

    Aosta Valley is a small alpine region of about 3.300 km2 located in the NW Italy, on the southern side of the Alps and surrounded by the highest Alpine peaks such as Mont Blanc (4810m), Mont Rose (4634m) and Cervino (4478m), More than 50% of the territory has an elevation above 2000 metres asl. High mountain, glacial and periglacial environments cover a significant part of the territory. As the cryosphere is strongly sensitive to climate change, global warming effects are particularly evident in this alpine region, and they often affect environment and social and economic life, thus representing a key issue for politicians and people working and living in the valley. Among these effects, some of the most important are the decrease of water storage due to glaciers retreat and the increasing natural hazards as a consequence of rapid environmental dynamics. Hence the importance of monitoring glacial and periglacial environment, in order to quantify effects of climate change, to detect new dynamics and to manage consequences on the environment and the social life. In Aosta Valley the understanding of these phenomena is carried out by means of several actions, both at a regional scale and on specific representative sites. A multi-temporal analysis of aerial photographs, orthophotos and satellite imagery allows to detect glaciers evolution trend at a regional scale. All this information is collected in a Regional Glacier inventory, according to the World Glaciers Inventory standard and recommendations. Analysis of the information collected in the Inventory show that the total area presently covered by glaciers is about 135 km2; area changes occurred in the past has been about -44.3 km2, and -17 km2. between 1975 and 2005. Glacier inventory also gathers - for each of the about 200 glaciers - morphological data, information about events and photos both historical and present. Glacier mass balance (the difference resulting from the mass gained by the glacier through the

  9. NATO Advanced Study Institute on Laser Control & Monitoring in New Materials, Biomedicine, Environment, Security & Defense

    CERN Document Server

    Hall, Trevor J; Paredes, Sofia A; Extreme Photonics & Applications

    2010-01-01

    "Extreme Photonics & Applications" arises from the 2008 NATO Advanced Study Institute in Laser Control & Monitoring in New Materials, Biomedicine, Environment, Security and Defense. Leading experts in the manipulation of light offered by recent advances in laser physics and nanoscience were invited to give lectures in their fields of expertise and participate in discussions on current research, applications and new directions. The sum of their contributions to this book is a primer for the state of scientific knowledge and the issues within the subject of photonics taken to the extreme frontiers: molding light at the ultra-finest scales, which represents the beginning of the end to limitations in optical science for the benefit of 21st Century technological societies. Laser light is an exquisite tool for physical and chemical research. Physicists have recently developed pulsed lasers with such short durations that one laser shot takes the time of one molecular vibration or one electron rotation in an ...

  10. The role of environmental biotechnology in exploring, exploiting, monitoring, preserving, protecting and decontaminating the marine environment.

    Science.gov (United States)

    Kalogerakis, Nicolas; Arff, Johanne; Banat, Ibrahim M; Broch, Ole Jacob; Daffonchio, Daniele; Edvardsen, Torgeir; Eguiraun, Harkaitz; Giuliano, Laura; Handå, Aleksander; López-de-Ipiña, Karmele; Marigomez, Ionan; Martinez, Iciar; Øie, Gunvor; Rojo, Fernando; Skjermo, Jorunn; Zanaroli, Giulio; Fava, Fabio

    2015-01-25

    In light of the Marine Strategy Framework Directive (MSFD) and the EU Thematic Strategy on the Sustainable Use of Natural Resources, environmental biotechnology could make significant contributions in the exploitation of marine resources and addressing key marine environmental problems. In this paper 14 propositions are presented focusing on (i) the contamination of the marine environment, and more particularly how to optimize the use of biotechnology-related tools and strategies for predicting and monitoring contamination and developing mitigation measures; (ii) the exploitation of the marine biological and genetic resources to progress with the sustainable, eco-compatible use of the maritime space (issues are very diversified and include, for example, waste treatment and recycling, anti-biofouling agents; bio-plastics); (iii) environmental/marine biotechnology as a driver for a sustainable economic growth. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. Power Balance AODV Routing Algorithm of WSN in Precision Agriculture Environment Monitoring

    Directory of Open Access Journals (Sweden)

    Xiaoqin Qin

    2013-11-01

    Full Text Available As one of important technologies of IOT (Internet of Things, WSN (Wireless Sensor Networks has been widely used in precision agriculture environment monitoring. WSN is a kind of energy-constrained network, but power balance is not taken into account in traditional routing protocols. A novel routing algorithm, named Power Balance Ad hoc On-Demand Distance Vector (PB-AODV, is proposed on cross-layer design. In the route discovery process of PB-AODV, routing path is established by the Received Signal Strength Indication (RSSI value. The optimal transmitting power, which is computed according to RSSI value, power threshold and node’s surplus energy, is encapsulated into Route Reply Packet. Hence, the sender node can adjust its transmission power to save energy according to the Route Reply Packet. Simulation results show that the proposed algorithm is effective for load balancing, and increases the WSN’s lifetime 14.3% consequently.

  12. Monitoring of radioactivity in the environs of Finnish nuclear power stations in 1987

    International Nuclear Information System (INIS)

    Sjoeblom, K.-L.; Klemola, S.; Ilus, E.; Arvela, H.; Blomqvist, L.

    1989-06-01

    Results of the environmental programmes for monitoring radioactive contamination around Finnish nuclear power plants in 1987 are reported. Fallout from the Chernobyl accident, which took place in April 1986, was still dominating the artificial radiation situation in Finland. Thus, large amounts of 137 Cs and other long-lived fallout nuclides predominated in the environmental samples taken in the vicinity of nuclear power plants. The extremely small airborne releases from Finnish nuclear power plants were almost totally covered by fallout nuclides. The somewhat higher aquatic releases were easier to distinguish, and it was possible to follow their spread in the marine environment. The contribution of locally discharged nuclides to radiation doses of the population was insignificant

  13. Monitoring of radioactive contamination in food and the environment 1986-1998

    International Nuclear Information System (INIS)

    Liland, Astrid; Skuterud, Lavrans; Bergan, Tone; Forseth, Torbjoern; Gaare, Eldar; Hellstroem, Turid

    2001-01-01

    The results from the national monitoring of radioactive contamination in food and the environment 1986-1998 are presented. The average 137Cs concentration is decreasing in cow's and goat's milk, sheep, reindeer and fresh water fish. Pasture and fungi are, on the contrary, not showing a general decreasing trend. The radioactivity in food and humans has been decreasing since 1987. The effective dose from intake is estimated to 0.02 mSv for an average Norwegian in 1998. Vulnerable groups may have received doses up to 0.4 mSv. One cannot rule out the possibility that some individuals in these groups have received doses superior to 1 mSv/year. (Author)

  14. Image Acquisition of Robust Vision Systems to Monitor Blurred Objects in Hazy Smoking Environments

    International Nuclear Information System (INIS)

    Ahn, Yongjin; Park, Seungkyu; Baik, Sunghoon; Kim, Donglyul; Nam, Sungmo; Jeong, Kyungmin

    2014-01-01

    Image information in disaster area or radiation area of nuclear industry is an important data for safety inspection and preparing appropriate damage control plans. So, robust vision system for structures and facilities in blurred smoking environments, such as the places of a fire and detonation, is essential in remote monitoring. Vision systems can't acquire an image when the illumination light is blocked by disturbance materials, such as smoke, fog, dust. The vision system based on wavefront correction can be applied to blurred imaging environments and the range-gated imaging system can be applied to both of blurred imaging and darken light environments. Wavefront control is a widely used technique to improve the performance of optical systems by actively correcting wavefront distortions, such as atmospheric turbulence, thermally-induced distortions, and laser or laser device aberrations, which can reduce the peak intensity and smear an acquired image. The principal applications of wavefront control are for improving the image quality in optical imaging systems such as infrared astronomical telescopes, in imaging and tracking rapidly moving space objects, and in compensating for laser beam distortion through the atmosphere. A conventional wavefront correction system consists of a wavefront sensor, a deformable mirror and a control computer. The control computer measures the wavefront distortions using a wavefront sensor and corrects it using a deformable mirror in a closed-loop. Range-gated imaging (RGI) is a direct active visualization technique using a highly sensitive image sensor and a high intensity illuminant. Currently, the range-gated imaging technique providing 2D and 3D images is one of emerging active vision technologies. The range-gated imaging system gets vision information by summing time sliced vision images. In the RGI system, a high intensity illuminant illuminates for ultra-short time and a highly sensitive image sensor is gated by ultra

  15. Image Acquisition of Robust Vision Systems to Monitor Blurred Objects in Hazy Smoking Environments

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Yongjin; Park, Seungkyu; Baik, Sunghoon; Kim, Donglyul; Nam, Sungmo; Jeong, Kyungmin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    Image information in disaster area or radiation area of nuclear industry is an important data for safety inspection and preparing appropriate damage control plans. So, robust vision system for structures and facilities in blurred smoking environments, such as the places of a fire and detonation, is essential in remote monitoring. Vision systems can't acquire an image when the illumination light is blocked by disturbance materials, such as smoke, fog, dust. The vision system based on wavefront correction can be applied to blurred imaging environments and the range-gated imaging system can be applied to both of blurred imaging and darken light environments. Wavefront control is a widely used technique to improve the performance of optical systems by actively correcting wavefront distortions, such as atmospheric turbulence, thermally-induced distortions, and laser or laser device aberrations, which can reduce the peak intensity and smear an acquired image. The principal applications of wavefront control are for improving the image quality in optical imaging systems such as infrared astronomical telescopes, in imaging and tracking rapidly moving space objects, and in compensating for laser beam distortion through the atmosphere. A conventional wavefront correction system consists of a wavefront sensor, a deformable mirror and a control computer. The control computer measures the wavefront distortions using a wavefront sensor and corrects it using a deformable mirror in a closed-loop. Range-gated imaging (RGI) is a direct active visualization technique using a highly sensitive image sensor and a high intensity illuminant. Currently, the range-gated imaging technique providing 2D and 3D images is one of emerging active vision technologies. The range-gated imaging system gets vision information by summing time sliced vision images. In the RGI system, a high intensity illuminant illuminates for ultra-short time and a highly sensitive image sensor is gated by ultra

  16. Effect-directed analysis supporting monitoring of aquatic environments--An in-depth overview.

    Science.gov (United States)

    Brack, Werner; Ait-Aissa, Selim; Burgess, Robert M; Busch, Wibke; Creusot, Nicolas; Di Paolo, Carolina; Escher, Beate I; Mark Hewitt, L; Hilscherova, Klara; Hollender, Juliane; Hollert, Henner; Jonker, Willem; Kool, Jeroen; Lamoree, Marja; Muschket, Matthias; Neumann, Steffen; Rostkowski, Pawel; Ruttkies, Christoph; Schollee, Jennifer; Schymanski, Emma L; Schulze, Tobias; Seiler, Thomas-Benjamin; Tindall, Andrew J; De Aragão Umbuzeiro, Gisela; Vrana, Branislav; Krauss, Martin

    2016-02-15

    Aquatic environments are often contaminated with complex mixtures of chemicals that may pose a risk to ecosystems and human health. This contamination cannot be addressed with target analysis alone but tools are required to reduce this complexity and identify those chemicals that might cause adverse effects. Effect-directed analysis (EDA) is designed to meet this challenge and faces increasing interest in water and sediment quality monitoring. Thus, the present paper summarizes current experience with the EDA approach and the tools required, and provides practical advice on their application. The paper highlights the need for proper problem formulation and gives general advice for study design. As the EDA approach is directed by toxicity, basic principles for the selection of bioassays are given as well as a comprehensive compilation of appropriate assays, including their strengths and weaknesses. A specific focus is given to strategies for sampling, extraction and bioassay dosing since they strongly impact prioritization of toxicants in EDA. Reduction of sample complexity mainly relies on fractionation procedures, which are discussed in this paper, including quality assurance and quality control. Automated combinations of fractionation, biotesting and chemical analysis using so-called hyphenated tools can enhance the throughput and might reduce the risk of artifacts in laboratory work. The key to determining the chemical structures causing effects is analytical toxicant identification. The latest approaches, tools, software and databases for target-, suspect and non-target screening as well as unknown identification are discussed together with analytical and toxicological confirmation approaches. A better understanding of optimal use and combination of EDA tools will help to design efficient and successful toxicant identification studies in the context of quality monitoring in multiply stressed environments. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Annual report on radioactive discharges from Winfrith and monitoring the environment 1991

    International Nuclear Information System (INIS)

    1992-05-01

    This annual report, the seventh, aims to provide full information on our discharges and environmental monitoring. The report is mainly graphical, comparing past and current levels with authorised limits, derived limits or the recommended limits of the International Commission on Radiological Protection (ICRP). Discharges from Winfrith are subject to Authorisations issued jointly by the Department of the Environment (DOE) and the Ministry of Agriculture, Fisheries and Food (MAFF). These Authorisations, one for discharges to the sea and one for discharges to the atmosphere, require that Winfrith establish a need to discharge; that we apply Best Practicable Means (BPM) to reduce our discharges; that our discharges are below set Authorised Limits; and that schedules of effluent and environmental monitoring are established. As a 'back stop', discharges at the limits must not result in doses to the most potentially exposed part of the local population - the critical group -exceeding 0.5 mSv per year. The limit recommended by the International Commission on Radiological Protection (ICRP) for dose to a member of the general public is 1.0 mSv per year. In September 1990 Winfrith's Steam Generating Heavy Water Reactor (SGHWR) was shut down therefore the pattern of discharges for 1991 differs from previous years. Discharges are generally reduced resulting in an even lower dose to the critical group, well below 1% of the ICRP limit and much less than 1% of the UK average natural background dose. (author)

  18. Online monitoring of dynamic tip clearance of turbine blades in high temperature environments

    Science.gov (United States)

    Han, Yu; Zhong, Chong; Zhu, Xiaoliang; Zhe, Jiang

    2018-04-01

    Minimized tip clearance reduces the gas leakage over turbine blade tips and improves the thrust and efficiency of turbomachinery. An accurate tip clearance sensor, measuring the dynamic clearances between blade tips and the turbine case, is a critical component for tip clearance control. This paper presents a robust inductive tip clearance sensor capable of monitoring dynamic tip clearances of turbine machines in high-temperature environments and at high rotational speeds. The sensor can also self-sense the temperature at a blade tip in situ such that temperature effect on tip clearance measurement can be estimated and compensated. To evaluate the sensor’s performance, the sensor was tested for measuring the tip clearances of turbine blades under various working temperatures ranging from 700 K to 1300 K and at turbine rotational speeds ranging from 3000 to 10 000 rpm. The blade tip clearance was varied from 50 to 2000 µm. The experiment results proved that the sensor can accurately measure the blade tip clearances with a temporal resolution of 10 µm. The capability of accurately measuring the tip clearances at high temperatures (~1300 K) and high turbine rotation speeds (~30 000 rpm), along with its compact size, makes it promising for online monitoring and active control of blade tip clearances of high-temperature turbomachinery.

  19. Development of a Flexible Lead-Free Piezoelectric Transducer for Health Monitoring in the Space Environment

    Directory of Open Access Journals (Sweden)

    Marco Laurenti

    2015-11-01

    Full Text Available In this work we report on the fabrication process for the development of a flexible piezopolymeric transducer for health monitoring applications, based on lead-free, piezoelectric zinc oxide (ZnO thin films. All the selected materials are compatible with the space environment and were deposited by the RF magnetron sputtering technique at room temperature, in view of preserving the total flexibility of the structures, which is an important requirement to guarantee coupling with cylindrical fuel tanks whose integrity we want to monitor. The overall transducer architecture was made of a c-axis-oriented ZnO thin film coupled to a pair of flexible Polyimide foils coated with gold (Au electrodes. The fabrication process started with the deposition of the bottom electrode on Polyimide foils. The ZnO thin film and the top electrode were then deposited onto the Au/Polyimide substrates. Both the electrodes and ZnO layer were properly patterned by wet-chemical etching and optical lithography. The assembly of the final structure was then obtained by gluing the upper and lower Polyimide foils with an epoxy resin capable of guaranteeing low outgassing levels, as well as adequate thermal and electrical insulation of the transducers. The piezoelectric behavior of the prototypes was confirmed and evaluated by measuring the mechanical displacement induced from the application of an external voltage.

  20. Micro Penning Trap for Continuous Magnetic Field Monitoring in High Radiation Environments

    Science.gov (United States)

    Latorre, Javiera; Bollen, Georg; Gulyuz, Kerim; Ringle, Ryan; Bado, Philippe; Dugan, Mark; Lebit Team; Translume Collaboration

    2016-09-01

    As new facilities for rare isotope beams, like FRIB at MSU, are constructed, there is a need for new instrumentation to monitor magnetic fields in beam magnets that can withstand the higher radiation level. Currently NMR probes, the instruments used extensively to monitor magnetic fields, do not have a long lifespans in radiation-high environments. Therefore, a radiation-hard replacement is needed. We propose to use Penning trap mass spectrometry techniques to make high precision magnetic field measurements. Our Penning microtrap will be radiation resistant as all of the vital electronics will be at a safe distance from the radiation. The trap itself is made from materials not subject to radiation damage. Penning trap mass spectrometers can determine the magnetic field by measuring the cyclotron frequency of an ion with a known mass and charge. This principle is used on the Low Energy Beam Ion Trap (LEBIT) minitrap at NSCL which is the foundation for the microtrap. We have partnered with Translume, who specialize in glass micro-fabrication, to develop a microtrap in fused-silica glass. A microtrap is finished and ready for testing at NSCL with all of the electronic and hardware components setup. DOE Phase II SBIR Award No. DE-SC0011313, NSF Award Number 1062410 REU in Physics, NSF under Grant No. PHY-1102511.

  1. Nuclear plant's virtual simulation for on-line radioactive environment monitoring and dose assessment for personnel

    International Nuclear Information System (INIS)

    Mol, Antonio Carlos A.; Jorge, Carlos Alexandre F.; Lapa, Celso Marcelo F.

    2009-01-01

    This paper reports the use of nuclear plant's simulation for online dose rate monitoring and dose assessment for personnel, using virtual reality technology. The platform used for virtual simulation was adapted from a low cost game engine, taking advantage of all its image rendering capabilities, as well as the physics for movement and collision, and networking capabilities for multi-user interactive navigation. A real nuclear plant was virtually modeled and simulated, so that a number of users can navigate simultaneously in this virtual environment in first or third person view, each one receiving visual information about both the radiation dose rate in each actual position, and the radiation dose received. Currently, this research and development activity has been extended to consider also on-line measurements collected from radiation monitors installed in the real plant that feed the simulation platform with dose rate data, through a TCP/IP network. Results are shown and commented, and other improvements are discussed, as the execution of a more detailed dose rate mapping campaign.

  2. Inter-comparison of personal monitors for nanoparticles exposure at workplaces and in the environment.

    Science.gov (United States)

    Todea, Ana Maria; Beckmann, Stefanie; Kaminski, Heinz; Bard, Delphine; Bau, Sébastien; Clavaguera, Simon; Dahmann, Dirk; Dozol, Hélène; Dziurowitz, Nico; Elihn, Karine; Fierz, Martin; Lidén, Göran; Meyer-Plath, Asmus; Monz, Christian; Neumann, Volker; Pelzer, Johannes; Simonow, Barbara Katrin; Thali, Patrick; Tuinman, Ilse; van der Vleuten, Arjan; Vroomen, Huub; Asbach, Christof

    2017-12-15

    Personal monitors based on unipolar diffusion charging (miniDiSC/DiSCmini, NanoTracer, Partector) can be used to assess the individual exposure to nanoparticles in different environments. The charge acquired by the aerosol particles is nearly proportional to the particle diameter and, by coincidence, also nearly proportional to the alveolar lung-deposited surface area (LDSA), the metric reported by all three instruments. In addition, the miniDiSC/DiSCmini and the NanoTracer report particle number concentration and mean particle size. In view of their use for personal exposure studies, the comparability of these personal monitors was assessed in two measurement campaigns. Altogether 29 different polydisperse test aerosols were generated during the two campaigns, covering a large range of particle sizes, morphologies and concentrations. The data provided by the personal monitors were compared with those obtained from reference instruments: a scanning mobility particle sizer (SMPS) for LDSA and mean particle size and a ultrafine particle counter (UCPC) for number concentration. The results indicated that the LDSA concentrations and the mean particle sizes provided by all investigated instruments in this study were in the order of ±30% of the reference value obtained from the SMPS when the particle sizes of the test aerosols generated were within 20-400nm and the instruments were properly calibrated. Particle size, morphology and concentration did not have a major effect within the aforementioned limits. The comparability of the number concentrations was found to be slightly worse and in the range of ±50% of the reference value obtained from the UCPC. In addition, a minor effect of the particle morphology on the number concentration measurements was observed. The presence of particles >400nm can drastically bias the measurement results of all instruments and all metrics determined. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. International Conference on SEMS 2012

    CERN Document Server

    Liu, Chuang; Scientific explanation and methodology of science; SEMS 2012

    2014-01-01

    This volume contains the contributed papers of invitees to SEMS 2012 who have also given talks at the conference. The invitees are experts in philosophy of science and technology from Asia (besides China), Australia, Europe, Latin America, North America, as well as from within China. The papers in this volume represent the latest work of each researcher in his or her expertise; and as a result, they give a good representation of the cutting-edge researches in diverse areas in different parts of the world.

  4. Virtual Environments for Visualizing Structural Health Monitoring Sensor Networks, Data, and Metadata.

    Science.gov (United States)

    Napolitano, Rebecca; Blyth, Anna; Glisic, Branko

    2018-01-16

    Visualization of sensor networks, data, and metadata is becoming one of the most pivotal aspects of the structural health monitoring (SHM) process. Without the ability to communicate efficiently and effectively between disparate groups working on a project, an SHM system can be underused, misunderstood, or even abandoned. For this reason, this work seeks to evaluate visualization techniques in the field, identify flaws in current practices, and devise a new method for visualizing and accessing SHM data and metadata in 3D. More precisely, the work presented here reflects a method and digital workflow for integrating SHM sensor networks, data, and metadata into a virtual reality environment by combining spherical imaging and informational modeling. Both intuitive and interactive, this method fosters communication on a project enabling diverse practitioners of SHM to efficiently consult and use the sensor networks, data, and metadata. The method is presented through its implementation on a case study, Streicker Bridge at Princeton University campus. To illustrate the efficiency of the new method, the time and data file size were compared to other potential methods used for visualizing and accessing SHM sensor networks, data, and metadata in 3D. Additionally, feedback from civil engineering students familiar with SHM is used for validation. Recommendations on how different groups working together on an SHM project can create SHM virtual environment and convey data to proper audiences, are also included.

  5. A WSN based Environment and Parameter Monitoring System for Human Health Comfort: A Cloud Enabled Approach

    Directory of Open Access Journals (Sweden)

    Manohara Pai

    2014-05-01

    Full Text Available The number and type of sensors measuring physical and physiological parameters have seen dramatic increase due to progress in the MEMS and Nano Technology. The Wireless Sensor Networks (WSNs in turn is bringing new applications in environment monitoring and healthcare in order to improve the quality of service especially in hospitals. The adequacy of WSNs to gather critical information has provided solution but with limited storage, computation and scalability. This limitation is addressed by integrating WSN with cloud services. But, once the data enters the cloud the owner has no control over it. Hence confidentiality and integrity of the data being stored in the cloud are compromised. In this proposed work, secure sensor-cloud architecture for the applications in healthcare is implemented by integrating two different clouds. The sink node of WSN outsources data into the cloud after performing operations to secure the data. Since the SaaS and IaaS environments of Cloud Computing are provided by two different cloud service providers (CSPs, both the CSPs will not have complete information of the architecture. This provides inherent security as data storage and data processing are done on different clouds.

  6. [POPULATION MONITORING OF THE HEALTH SHAPING ENVIRONMENT OF THE STUDENTS OF NAGORNO KARABAKH].

    Science.gov (United States)

    Galstyan, H

    2016-10-01

    The study of the health shaping environment of students is one of the actual biomedical tasks, it is also the scientific founding for conducting health-preventive and health-preserving measures. Despite the importance of the proposed problem, this study is a pioneering attempt in Nagorno Karabakh. The objective of the work is the scientific grounding of regional peculiarities and the contemporary level of health shaping environment of students on the basis of population monitoring system. The results of the study prove that the studied health criteria are within limits of physiological norm. The most wide-spead risk factors are lack of physical activity, in the group of young boys - also tobacco use and alcohol consumption. The analysis of daily diet of examinees attests ''fat'' nutrition model. The data on the impact of physical effort reveal high tension in the cardiac activity in the group of physically untrained students. The study of the impact of educational and mental strain on the functional state of the organism of the students revealed that daily academic leads to fatigue. The examination session is characterized by strongly expressed sympatotonia sympathicotonia, mental strain - by parasympatotonia. The obtained results point to the necessity of the enhanced control in preserving and strengthening the health of the younger generation considering the above-brought regional peculiarities.

  7. Comparison of passive sampling and biota for monitoring of tonalide in aquatic environment.

    Science.gov (United States)

    Tumova, Jitka; Grabicova, Katerina; Golovko, Oksana; Koba, Olga; Kodes, Vit; Fedorova, Ganna; Grabic, Roman; Kroupova, Hana Kocour

    2017-10-01

    Synthetic musk compounds are extensively used in personal care and cosmetic products all over the world. Afterwards, they are discharged into the environment mainly because they are not completely removed in wastewater treatment plants. The aim of this study was to investigate if a passive sampler is applicable for the monitoring of tonalide, a polycyclic musk compound, in the aquatic environment and to compare the levels of tonalide in pesticide-polar organic chemical integrative sampler (POCIS) and biota. For this purpose, four sampling localities on the three biggest rivers in the Czech Republic were selected. Tonalide was determined in POCIS at all sampling sites in the concentration ranging from 9 ng/POCIS (Labe River, Hradec Králové) to 25 ng/POCIS (Morava River, Blatec). The locality with the most frequent occurrence of tonalide in biota samples was the Morava River which well corresponded with the highest tonalide concentration in POCIS among sampling sites. The highest number of positive tonalide detections among all studied biota samples was found in fish plasma. To the best of our knowledge, this is the first evidence that tonalide bioaccumulates in fish blood. Tonalide levels were below the limit of quantification in benthos samples at all sampling sites.

  8. Longitudinal monitoring of Listeria monocytogenes and Listeria phages in seafood processing environments in Thailand.

    Science.gov (United States)

    Vongkamjan, Kitiya; Benjakul, Soottawat; Kim Vu, Hue Thi; Vuddhakul, Varaporn

    2017-09-01

    Listeria monocytogenes is a foodborne pathogen commonly found in environments of seafood processing, thus presenting a challenge for eradication from seafood processing facilities. Monitoring the prevalence and subtype diversity of L. monocytogenes together with phages that are specific to Listeria spp. ("Listeria phages") will provide knowledge on the bacteria-phage ecology in food processing plants. In this work, a total of 595 samples were collected from raw material, finished seafood products and environmental samples from different sites of a seafood processing plant during 17 sampling visits in 1.5 years of study. L. monocytogenes and Listeria spp. (non-monocytogenes) were found in 22 (3.7%) and 43 (7.2%) samples, respectively, whereas 29 Listeria phages were isolated from 9 (1.5%) phage-positive samples. DNA fingerprint analysis of L. monocytogenes isolates revealed 11 Random Amplified Polymorphic DNA (RAPD) profiles, with two subtypes were frequently observed over time. Our data reveal a presence of Listeria phages within the same seafood processing environments where a diverse set of L. monocytogenes subtypes was also found. Although serotype 4b was observed at lower frequency, data indicate that isolates from this seafood processing plant belonged to both epidemiologically important serotypes 1/2a and 4b, which may suggest a potential public health risk. Phages (all showed a unique genome size of 65 ± 2 kb) were classified into 9 host range groups, representing both broad- and narrow-host range. While most L. monocytogenes isolates from this facility were susceptible to phages, five isolates showed resistance to 12-20 phages. Variations in phage host range among Listeria phages isolated from food processing plant may affect a presence of a diverse set of L. monocytogenes isolates derived from the same processing environment in Thailand. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Advanced Oil Spill Detection Algorithms For Satellite Based Maritime Environment Monitoring

    Science.gov (United States)

    Radius, Andrea; Azevedo, Rui; Sapage, Tania; Carmo, Paulo

    2013-12-01

    During the last years, the increasing pollution occurrence and the alarming deterioration of the environmental health conditions of the sea, lead to the need of global monitoring capabilities, namely for marine environment management in terms of oil spill detection and indication of the suspected polluter. The sensitivity of Synthetic Aperture Radar (SAR) to the different phenomena on the sea, especially for oil spill and vessel detection, makes it a key instrument for global pollution monitoring. The SAR performances in maritime pollution monitoring are being operationally explored by a set of service providers on behalf of the European Maritime Safety Agency (EMSA), which has launched in 2007 the CleanSeaNet (CSN) project - a pan-European satellite based oil monitoring service. EDISOFT, which is from the beginning a service provider for CSN, is continuously investing in R&D activities that will ultimately lead to better algorithms and better performance on oil spill detection from SAR imagery. This strategy is being pursued through EDISOFT participation in the FP7 EC Sea-U project and in the Automatic Oil Spill Detection (AOSD) ESA project. The Sea-U project has the aim to improve the current state of oil spill detection algorithms, through the informative content maximization obtained with data fusion, the exploitation of different type of data/ sensors and the development of advanced image processing, segmentation and classification techniques. The AOSD project is closely related to the operational segment, because it is focused on the automation of the oil spill detection processing chain, integrating auxiliary data, like wind information, together with image and geometry analysis techniques. The synergy between these different objectives (R&D versus operational) allowed EDISOFT to develop oil spill detection software, that combines the operational automatic aspect, obtained through dedicated integration of the processing chain in the existing open source NEST

  10. Planktonic foraminiferal abnormalities in coastal and open marine eastern Mediterranean environments: A natural stress monitoring approach in recent and early Holocene marine systems

    Science.gov (United States)

    Antonarakou, A.; Kontakiotis, G.; Zarkogiannis, S.; Mortyn, P. G.; Drinia, H.; Koskeridou, E.; Anastasakis, G.

    2018-05-01

    Marine environmental status can be assessed through the study of bio-indicator species. Here, we monitor natural environmental stress by the occurrence of morphologically abnormal planktonic foraminiferal specimens from a suite of surface sediments in the eastern Mediterranean Sea. We also compare Scanning Electron Microscopy (SEM) abnormality observations from sapropel S1-derived sediments in the Aegean, Libyan and Levantine basins, since they provide a direct record of a natural stress experiment that took place over past time scales. At initial sapropel deposition levels, we observe increased growth asymmetry in Globigerinoides ruber twinned and twisted individuals, possibly associated with eutrophication and anoxia. In modern material, a range of malformations and aberrant morphologies from slight deformity with smaller or overdeveloped chambers to more severe deformity with abnormally protruding or misplaced chambers, distorted spirals, and double tests is also observed, as a result of the hypersaline, oligotrophic and oxygen-depleted nature of the Mediterranean Sea water column. Overall, we highlight the current use of the relative abundance of abnormal tests as a bio-indicator for monitoring natural stress, especially the occurrence of twin specimens as indicative of high-salinity stress conditions, and further illustrate the necessity to map both their spatial and temporal distribution for accurate paleoenvironmental reconstructions. Such an approach presents the advantage to rapidly provide information over wide spatial and temporal scales, extending our ability to monitor a wide variety of environments (from coastal to the open-sea). However, further investigations should extend this approach to test the robustness of our findings in a number of similar oceanic settings.

  11. Trends in monitoring pharmaceuticals and personal-care products in the aquatic environment by use of passive sampling devices

    Science.gov (United States)

    Mills, G.A.; Vrana, B.; Allan, I.; Alvarez, D.A.; Huckins, J.N.; Greenwood, R.

    2007-01-01

    The use of passive sampling in monitoring pharmaceuticals and personal-care products (PPCPs) in the aquatic environment is discussed. The utility of passive sampling methods for monitoring the fraction of heavy metals and the biologically available fraction of non-polar organic priority pollutants is recognized and these technologies are being used in surveys of water quality. These devices are used to measure the dissolved fraction and they can yield information that can be used in the development of risk assessments models. These devices can also be used to locate illegal dumping and to monitor specific sources of input of PPCPs into the environment, or to monitor the effectiveness of water treatment processes in the removal of these compounds from wastewater. These devices can provide representative information at low cost which necessitate a combination of laboratory calibration and field studies for emerging pollutants.

  12. semPLS: Structural Equation Modeling Using Partial Least Squares

    Directory of Open Access Journals (Sweden)

    Armin Monecke

    2012-05-01

    Full Text Available Structural equation models (SEM are very popular in many disciplines. The partial least squares (PLS approach to SEM offers an alternative to covariance-based SEM, which is especially suited for situations when data is not normally distributed. PLS path modelling is referred to as soft-modeling-technique with minimum demands regarding mea- surement scales, sample sizes and residual distributions. The semPLS package provides the capability to estimate PLS path models within the R programming environment. Different setups for the estimation of factor scores can be used. Furthermore it contains modular methods for computation of bootstrap confidence intervals, model parameters and several quality indices. Various plot functions help to evaluate the model. The well known mobile phone dataset from marketing research is used to demonstrate the features of the package.

  13. Final annual report of the Partial monitoring system 'Radioactivity of the environment' 2014

    International Nuclear Information System (INIS)

    Melicherova, T.; Cabanekova, H.; Bodorova, J.

    2015-01-01

    The present report evaluates activities of radiation monitoring of Slovak Hydrometeorological Institute (SHMI) in 2014. Analytical part focuses on detailed statistical analysis of monitored data. Detailed knowledge of the course of time series during uneventful period enables early detect and analyze potential increase of radioactivity levels in the environment originating from domestic or foreign sources. SHMI is responsible for international data exchange with the European Commission and with partners in Austria and Hungary.

  14. Persistent Monitoring of Urban Infrasound Phenomenology-Report 2: Investigation of Structural Infrasound Signals in an Urban Environment

    Science.gov (United States)

    2016-11-01

    rural environments where anthropological noise sources are limited. As interest in monitoring sources at local distances grows in the infrasound...TASK NUMBER 5f. WORK UNIT NUMBER J62BH4 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NUMBER U.S...where anthropological noise sources are limited. As interest in monitoring sources at local distances grows in the infrasound community, it is vital to

  15. The Effect of Nonnormality on CB-SEM and PLS-SEM Path Estimates

    OpenAIRE

    Z. Jannoo; B. W. Yap; N. Auchoybur; M. A. Lazim

    2014-01-01

    The two common approaches to Structural Equation Modeling (SEM) are the Covariance-Based SEM (CB-SEM) and Partial Least Squares SEM (PLS-SEM). There is much debate on the performance of CB-SEM and PLS-SEM for small sample size and when distributions are nonnormal. This study evaluates the performance of CB-SEM and PLS-SEM under normality and nonnormality conditions via a simulation. Monte Carlo Simulation in R programming language was employed to generate data based on the theoretical model w...

  16. Real-time on-line space research laboratory environment monitoring with off-line trend and prediction analysis

    Science.gov (United States)

    Jules, Kenol; Lin, Paul P.

    2007-06-01

    With the International Space Station currently operational, a significant amount of acceleration data is being down-linked, processed and analyzed daily on the ground on a continuous basis for the space station reduced gravity environment characterization, the vehicle design requirements verification and science data collection. To help understand the impact of the unique spacecraft environment on the science data, an artificial intelligence monitoring system was developed, which detects in near real time any change in the reduced gravity environment susceptible to affect the on-going experiments. Using a dynamic graphical display, the monitoring system allows science teams, at any time and any location, to see the active vibration disturbances, such as pumps, fans, compressor, crew exercise, re-boost and extra-vehicular activities that might impact the reduced gravity environment the experiments are exposed to. The monitoring system can detect both known and unknown vibratory disturbance activities. It can also perform trend analysis and prediction by analyzing past data over many increments (an increment usually lasts 6 months) collected onboard the station for selected disturbances. This feature can be used to monitor the health of onboard mechanical systems to detect and prevent potential systems failures. The monitoring system has two operating modes: online and offline. Both near real-time on-line vibratory disturbance detection and off-line detection and trend analysis are discussed in this paper.

  17. SCIENTIFIC AND INNOVATIVE APPROACH TO PROBLEM PERTAINING TO EVALUATION AND MONITORING OF ENVIRONMENT QUALITY IN REPUBLIC OF BELARUS

    Directory of Open Access Journals (Sweden)

    I. V. Voytov

    2009-01-01

    Full Text Available The paper proposes a scientific and innovative approach to solution of an important problem in the field of rational nature management and ecology which presupposes realization of evaluation, analysis and monitoring of environment  quality  (EQ in Belarus.  This  approach is based on methods and  facilities  of  administrative-command  and  partially  automatic-control  management.   The  main components of the innovative approach are an automatic  system for  evaluation and monitoring of EQ including estimation and formation of nature-resource potential within 11 cadaster and other data base, general principles on evaluation and monitoring of EQ, structural and algorithmic schemes for evaluation of ecological state of administrative territories, calculation of generalized indices of nature-territorial complexes and solution of nature protection problems in respect of EQ monitoring. A system of equation calculation for the analysis and evaluation of technogenic load on main nature components of the environment (free air, water objects, soil cover, realization of monitoring function in respect of EQ and ecological state of local and urban territories, nature resources  and enterprises, pollution and state of some recipients and also data resources for execution of analytical calculations and functions directed on monitoring quality of nature components of the environment is advanced in the paper.

  18. SiC Sensors in Extreme Environments: Real-time Hydrogen Monitoring for Energy Plant Applications

    Science.gov (United States)

    Ghosh, Ruby

    2008-03-01

    Clean, efficient energy production, such as the gasification of coal (syngas), requires physical and chemical sensors for exhaust gas monitoring as well as real-time control of the combustion process. Wide-bandgap semiconducting materials systems can meet the sensing demands in these extreme environments consisting of chemically corrosive gases at high temperature and pressure. We have developed a SiC based micro-sensor for detection of hydrogen containing species with millisecond response at 600 C. The sensor is a Pt-SiO2-SiC device with a dense Pt catalytic sensing film, capable of withstanding months of continuous high temperature operation. The device was characterized in robust sensing module that is compatible with an industrial reactor. We report on the performance of the SiC sensor in a simulated syngas ambient at 370 C containing the common interferants CO2, CH4 and CO [1]. In addition we demonstrate that hours of exposure to >=1000 ppm H2S and 15% water vapor does not degrade the sensor performance. To elucidate the mechanisms responsible for the hydrogen response of the sensor we have modeled the hydrogen adsorptions kinetics at the internal Pt-SiO2 interface, using both the Tempkin and Langmuir isotherms. Under the conditions appropriate for energy plant applications, the response of our sensor is significantly larger than that obtained from ultra-high vacuum electrochemical sensor measurements at high temperatures. We will discuss the role of morphology, at the nano to micro scale, on the enhanced catalytic activity observed for our Pt sensing films in response to a heated hydrogen gas stream at atmospheric pressure. [1] R. Loloee, B. Chorpening, S. Beers & R. Ghosh, Hydrogen monitoring for power plant applications using SiC sensors, Sens. Actuators B:Chem. (2007), doi:10.1016/j.snb.2007.07.118

  19. Semipermeable membrane devices in monitoring of organic pollutants in the aquatic environment

    Energy Technology Data Exchange (ETDEWEB)

    Sabaliunas, D

    1999-03-01

    Semipermeable membrane devices (SPMDs) are passive samplers capable of concentrating hydrophobic chemicals from water, sediments, soil and air. They consist of layflat polymeric membrane such as polyethylene containing a thin film of synthetic lipid such as triolein. The transport of hydrophobic chemicals through the membrane into the lipid is governed by the process of passive diffusion. Therefore, SPMDs sample chemicals in a way similar to organisms. This thesis deals with the application of SPMDs in the monitoring of concentrations and effects of organic pollutants in the aquatic environment. SPMDs were exposed to various pesticides (organochlorines, synthetic pyrethroids, dinitroanilines, amides) in laboratory flow-through experiments to study the uptake kinetics of organic chemicals from water. To compare the uptake of model compounds by SPMDs and aquatic organisms, the membrane samplers were exposed to chemicals side-by-side with bivalves. Mixtures of chemicals accumulated by SPMDs and mussels were tested in standard toxicity and genotoxicity assays (Microtox, Mutatox, invertebrate toxicity tests, the Ames test, sister chromatid exchange test). These studies showed that the uptake pattern of organic compounds by SPMDs and aquatic organisms was similar, and the passive samplers accumulated levels of chemicals sufficient for standard bioassays. To further validate the method, SPMDs were deployed in a number of polluted water sources in Lithuania. Bioassay-directed fractionation and chemical analytical methods were used to identify pollutants sampled (PAHs, PCBs, organochlorines) and their effects were evaluated in bioassays. SPMDs proved to be useful tools in monitoring of organic pollutants under the field conditions. Criteria for bioassays to be integrated with the SPMD technique were defined based on the results of these studies. Some important factors in the integration of SPMDs and bioassays (toxicity of SPMD-inherent oleic and sediment

  20. The marine environment monitoring in Saco Piraquara de Fora after the beginning of the Angra 2 nuclear power plant operation

    International Nuclear Information System (INIS)

    Tavares, P.G.; Souza, R.F.; Cardoso, S.N.M.

    2009-01-01

    The goal of this paper is to evaluate the environmental monitoring around the Almirante Alvaro Alberto Nuclear Power Station after the beginning the operation of Unit II, in July 2000. The Environmental Monitoring Laboratory collects several environmental samples and analyses them radiometrically to determine the presence of artificial radionuclides. In the Environmental Monitoring Laboratory, the samples are prepared and analysed following international procedures and the activities of the detectable radionuclides are obtained by gamma spectrometry. The Environmental Monitoring Laboratory analyses tritium in sea water as well. This paper will describe only the monitoring of the marine samples and the results of the measurements are compared with those obtained in pre-operational time of Angra 1 (1978 - 1982), Angra 2 (1996 - 2000) and those obtained in operational time of the units until 2008. The results show that, since 1982 until now, there is no impact on marine environment caused by the operation of Angra 1 and Angra 2. (author)

  1. Overview of the atmospheric ionizing radiation environment monitoring by Bulgarian build instruments

    Science.gov (United States)

    Dachev, Tsvetan; Tomov, Borislav; Matviichuk, Yury; Dimitrov, Plamen; Spurny, Frantisek; Ploc, Ondrej; Uchihori, Yukio; Flueckiger, Erwin; Kudela, Karel; Benton, Eric

    2012-10-01

    Humans are exposed to ionizing radiation all the time, and it is known that it can induce a variety of harmful biological effects. Consequently, it is necessary to quantitatively assess the level of exposure to this radiation as the basis for estimating risks for their health. Spacecraft and aircraft crews are exposed to elevated levels of cosmic radiation of galactic and solar origin and to secondary radiation produced in the atmosphere, the vehicle structure and its contents. The aircraft crew monitoring is required by the following recommendations of the International Commission on Radiological Protection (ICRP) (ICRP 1990), the European Union (EU) introduced a revised Basic Safety Standards Directive (EC 1997) which, inter alia, included the exposure to cosmic radiation. This approach has been also adopted in other official documents (NCRP 2002). In this overview we present the results of ground based, mountain peaks, aircraft, balloon and rocket radiation environment monitoring by means of a Si-diode energy deposition spectrometer Liulin type developed first in Bulgarian Academy of Sciences (BAS) for the purposes of the space radiation monitoring at MIR and International Space Station (ISS). These spectrometers-dosemeters are further developed, calibrated and used by scientific groups in different countries. Calibration procedures of them are performed at different accelerators including runs in the CERN high-energy reference field, simulating the radiation field at 10 km altitude in the atmosphere and with heavy ions in Chiba, Japan HIMAC accelerator were performed also. The long term aircraft data base were accumulated using specially developed battery operated instrument in 2001-2009 years onboard of A310-300 aircrafts of Czech Air Lines, during 24 about 2 months runs with more than 2000 flights and 13500 flight hours on routes over the Atlantic Ocean mainly. The obtained experimental data are compared with computational models like CARI and EPCARD. The

  2. Annual report on radioactive discharges and monitoring of the environment 1986

    International Nuclear Information System (INIS)

    1987-01-01

    British Nuclear Fuels plc (BNFL) provides a comprehensive range of nuclear fuel cycle services, ie the purification and processing of uranium ore concentrates, the enrichment of uranium, the manufacture of uranium and plutonium based fuels, the reprocessing of irradiated fuel, and the conditioning and storage of nuclear materials and radioactive wastes. Some of these activities give rise to discharges of radioactive isotopes to the environment. This annual report follows the pattern established in 1977 in that it gives information on radioactive discharges, through authorised and scheduled outlets, and on environmental monitoring for all of the Company's Works and sites, ie Sellafield Site and the Drigg Storage and Disposal Site; Chapelcross Works; Springfield Works and the Ulnes Walton Disposal Site; and Capenhurst Works. Where a site also encompasses laboratories of the United Kingdom Atomic Energy Authority (UKAEA) reference is made to the significance of the discharges from the latter. It also includes assessment of radiation doses to representative members of the most highly exposed group of the general population (the critical group) for the most important environmental pathways in the vicinity of each site. Information for the period 1971-76 inclusive has also been published by BNFL and prior to 1971, the year in which BNFL was formed, information was published by the UKAEA. An appendix contains certificates of Authorisation granted by the DOE, MAFF and Scottish Office imposing limits and conditions relating to methods of disposal and quantities to be discharged. (author)

  3. Monitoring psychrotrophic lactic acid bacteria contamination in a ready-to-eat vegetable salad production environment.

    Science.gov (United States)

    Pothakos, Vasileios; Snauwaert, Cindy; De Vos, Paul; Huys, Geert; Devlieghere, Frank

    2014-08-18

    A study monitoring lactic acid bacteria contamination was conducted in a company producing fresh, minimally processed, packaged and ready-to-eat (RTE) vegetable salads (stored at 4°C) in order to investigate the reason for high psychrotrophic LAB levels in the products at the end of shelf-life. Initially, high microbial counts exceeding the established psychrotrophic thresholds (>10(7)-10(8)CFU/g) and spoilage manifestations before the end of the shelf-life (7days) occurred in products containing an assortment of sliced and diced vegetables, but within a one year period these spoilage defects became prevalent in the entire processing plant. Environmental sampling and microbiological analyses of the raw materials and final products throughout the manufacturing process highlighted the presence of high numbers of Leuconostoc spp. in halved and unseeded, fresh sweet bell peppers provided by the supplier. A combination of two DNA fingerprinting techniques facilitated the assessment of the species diversity of LAB present in the processing environment along with the critical point of their introduction in the production facility. Probably through air mediation and surface adhesion, mainly members of the strictly psychrotrophic species Leuconostoc gelidum subsp. gasicomitatum and L. gelidum subsp. gelidum were responsible for the cross-contamination of every vegetable handled within the plant. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. Wave Glider Monitoring of Sediment Transport and Dredge Plumes in a Shallow Marine Sandbank Environment.

    Science.gov (United States)

    Van Lancker, Vera; Baeye, Matthias

    2015-01-01

    As human pressure on the marine environment increases, safeguarding healthy and productive seas increasingly necessitates integrated, time- and cost-effective environmental monitoring. Employment of a Wave Glider proved very useful for the study of sediment transport in a shallow sandbank area in the Belgian part of the North Sea. During 22 days, data on surface and water-column currents and turbidity were recorded along 39 loops around an aggregate-extraction site. Correlation with wave and tidal-amplitude data allowed the quantification of current- and wave-induced advection and resuspension, important background information to assess dredging impacts. Important anomalies in suspended particulate matter concentrations in the water column suggested dredging-induced overflow of sediments in the near field (i.e., dynamic plume), and settling of finer-grained material in the far field (i.e., passive plume). Capturing the latter is a successful outcome to this experiment, since the location of dispersion and settling of a passive plume is highly dependent on the ruling hydro-meteorological conditions and thus difficult to predict. Deposition of the observed sediment plumes may cause habitat changes in the long-term.

  5. Development of an Indoor Airflow Energy Harvesting System for Building Environment Monitoring

    Directory of Open Access Journals (Sweden)

    Fei Fei

    2014-05-01

    Full Text Available Wireless sensor networks (WSNs have been widely used for intelligent building management applications. Typically, indoor environment parameters such as illumination, temperature, humidity and air quality are monitored and adjusted by an intelligent building management system. However, owing to the short life-span of the batteries used at the sensor nodes, the maintenance of such systems has been labor-intensive and time-consuming. This paper discusses a battery-less self-powering system that converts the mechanical energy from the airflow in ventilation ducts into electrical energy. The system uses a flutter energy conversion device (FECD capable of working at low airflow speeds while installed on the ventilation ducts inside of buildings. A power management strategy implemented with a circuit system ensures sufficient power for driving commercial electronic devices. For instance, the power management circuit is capable of charging a 1 F super capacitor to 2 V under ventilation duct airflow speeds of less than 3 m/s.

  6. Wave Glider Monitoring of Sediment Transport and Dredge Plumes in a Shallow Marine Sandbank Environment.

    Directory of Open Access Journals (Sweden)

    Vera Van Lancker

    Full Text Available As human pressure on the marine environment increases, safeguarding healthy and productive seas increasingly necessitates integrated, time- and cost-effective environmental monitoring. Employment of a Wave Glider proved very useful for the study of sediment transport in a shallow sandbank area in the Belgian part of the North Sea. During 22 days, data on surface and water-column currents and turbidity were recorded along 39 loops around an aggregate-extraction site. Correlation with wave and tidal-amplitude data allowed the quantification of current- and wave-induced advection and resuspension, important background information to assess dredging impacts. Important anomalies in suspended particulate matter concentrations in the water column suggested dredging-induced overflow of sediments in the near field (i.e., dynamic plume, and settling of finer-grained material in the far field (i.e., passive plume. Capturing the latter is a successful outcome to this experiment, since the location of dispersion and settling of a passive plume is highly dependent on the ruling hydro-meteorological conditions and thus difficult to predict. Deposition of the observed sediment plumes may cause habitat changes in the long-term.

  7. Performance monitoring of an improved disposal trench in a humid environment in a fractured geology

    International Nuclear Information System (INIS)

    Mills, D.; Razor, J.

    1988-01-01

    An engineering evaluation of an improved disposal trench at the Maxey Flats Waste Disposal Site is being conducted in order to demonstrate the feasibility of a burial trench suitable for use at a site in a humid environment and underlain by complex and fractured geologic media. This demonstration is one of several proposed final site stabilization alternatives which will have to be evaluated prior to final site closure. Due to requirements in the Central Midwest Compact Commission, no waste generated as a result of the site closure may be disposed in the Commission's disposal site. Hence, the waste will be disposed on-site. The demonstration trench was constructed and filled with waste during the fall of 1985 with final trench capping being completed in July 1986. Since that time the trench has been evaluated utilizing trench settlement monument elevations, leachate production measurements, leachate radionuclide analysis, chemical tracer analysis and trench water balance. Measurements performed to date indicated that the trench lower infiltration barrier has a permeability of about 1E-7 cm/sec. Water balance measurements indicated that less than one percent of the total rainfall crossed the trench capillary barrier. No settlement of the trench cap has been observed. No liquid has appeared in the leachate collection and monitoring sumps

  8. Sexual Arousal and Sexually Explicit Media (SEM)

    DEFF Research Database (Denmark)

    Hald, Gert Martin; Stulhofer, Aleksandar; Lange, Theis

    2018-01-01

    -mainstream and mainstream SEM groups, and (iii) to explore the validity and predictive accuracy of the Non-Mainstream Pornography Arousal Scale (NPAS). METHODS: Online cross-sectional survey of 2,035 regular SEM users in Croatia. MAIN OUTCOMES MEASURES: Patterns of sexual arousal to 27 different SEM themes, sexual...

  9. Use of portable exposimeters to monitor radiofrequency electromagnetic field exposure in the everyday environment.

    Science.gov (United States)

    Sagar, Sanjay; Struchen, Benjamin; Finta, Viktoria; Eeftens, Marloes; Röösli, Martin

    2016-10-01

    Spatial and temporal distribution of radiofrequency electromagnetic field (RF-EMF) levels in the environment is highly heterogeneous. It is thus not entirely clear how to monitor spatial variability and temporal trends of RF-EMF exposure levels in the environment in a representative and efficient manner. The aim of this study was to test a monitoring protocol for RF-EMF measurements in public areas using portable devices. Using the ExpoM-RF devices mounted on a backpack, we have conducted RF-EMF measurements by walking through 51 different outdoor microenvironments from 20 different municipalities in Switzerland: 5 different city centers, 5 central residential areas, 5 non-central residential areas, 15 rural residential areas, 15 rural centers and 6 industrial areas. Measurements in public transport (buses, trains, trams) were collected when traveling between the areas. Measurements were conducted between 25th March and 11th July 2014. In order to evaluate spatial representativity within one microenvironment, we measured two crossing paths of about 1km in length in each microenvironment. To evaluate repeatability, measurements in each microenvironment were repeated after two to four months on the same paths. Mean RF-EMF exposure (sum of 15 main frequency bands between 87.5 and 5,875MHz) was 0.53V/m in industrial zones, 0.47V/m in city centers, 0.32V/m in central residential areas, 0.25V/m non-central residential areas, 0.23V/m in rural centers and rural residential areas, 0.69V/m in trams, 0.46V/m in trains and 0.39V/m in buses. Major exposure contribution at outdoor locations was from mobile phone base stations (>80% for all outdoor areas with respect to the power density scale). Temporal correlation between first and second measurement of each area was high: 0.89 for total RF-EMF, 0.90 for all five mobile phone downlink bands combined, 0.51 for all five uplink bands combined and 0.79 for broadcasting. Spearman correlation between arithmetic mean values of the

  10. Grey Incidence analyze of Environment Monitoring Data and Research on the Disease Prevention Measures of Longmen Grottoes

    Science.gov (United States)

    LeiLei, Zheng; XueZhi, Fu; Fei, Chu

    2018-05-01

    Longmen Grottoes was afflicted with many diseases for a long period such as weathering, seepage water and organism growth. Those adverse factors were threatening to preserve cultural relic. Longmen Grottoes conservation and restoration project being put into effect by UNESCO in 2002. The Longmen Grottoes area environmental monitoring system was built in order to comprehensively master the distribution law of environmental factors over the Longmen Grottoes. The monitoring items contains temperature, humidity, wind direction, wind speed, precipitation, light intensity,water content in soil, the rock surface temperature and so on. At the same time, monitoring three experiment caves, monitoring the inside temperature, humidity, seepage water and the wall face temperature etc. So as to analyze the relationship between cave environment and regional environment. We statistical and arrange the data using Excel software, Kgraph software and DPS software. Through the grey incidence analyze, the incidence matrix and the correlation degree of the environmental factors was obtained[1]. The main environment factors for the formation of the disease had been researched. Based on the existing environmental monitor data, the relevance of seepage water and fracture displacement with other environmental factors had been studied, and the relational order was obtained. Corresponding preventive measures were put forward by the formation mechanism analyze of the disease.

  11. The use of embedded sensors for the monitoring of adhesive joints in marine environments

    Science.gov (United States)

    McGovern, Scott T.; Spinks, Geoffrey M.; Wallace, Gordon G.

    2005-05-01

    A copolymer incorporating polyaniline was used as a sensing medium in the construction of a resistance based humidity sensor. Aniline monomer was polymerised in the presence of poly (butyl acrylate / vinyl acetate) and a copolymer containing polyaniline emeraldine salt was obtained. The sensing medium was then developed by redissolving 1-2 w/w% of the resulting polymer residue in dichloromethane to produce a processable polymer blend solution. Some of this polymer residue was also de-doped in a solution of ammonia, and then washed with distilled water until the waste water had a neutral pH. This residue was then redissolved at 1-2 w/w% in dichloromethane to produce a second processable polymer blend this time containing polyaniline emeraldine base. The final sensor design utilised 125μm polyester insulated platinum wire as conducting electrodes that were dip coated in the emeraldine salt copolymer solution and allowed to dry in a desiccator. The sensor was then dip-coated in a protective barrier layer of the emeraldine base copolymer to prevent over-oxidation and/or de-protonation of the emeraldine salt sensing medium under this coating. The sensors had an overall final thickness of less than 150μm and showed high sensitivity to humidity, low resistance, and good reversibility without hysteresis. Sensors were monitored for 2-probe resistance changes when in contact with water. Calibration curves for each sensor were produced to convert the resistance reading to mass uptake of water. Individual sensors were embedded within Aluminium 5083 / Araldite 2015 adhesive joints to monitor mass uptake of water when exposed to marine environments. Correlations between mass uptake of water and joint strength were made. There are various advantages of such a sensor design. Polymer based thin film humidity sensors have the advantage that the high processability of the material allows for simple fabrication of a range of geometries including smaller sensor designs. The ease of

  12. Report of the consultant's meeting on monitoring accidentally released radionuclides in the environment

    International Nuclear Information System (INIS)

    2001-01-01

    At an earlier Research Co-ordination Meeting (12-16 August 1991, VIC, Vienna) for the IAEA Programme on 'Rapid Instrumental and Separation Methods for Monitoring Radionuclides in Food and Environmental Samples', it was recognized that a network of analytical laboratories with specially qualified scientists is needed which will provide a timely coordinated response to any future requests for assistance from Member States. The experience gained from the International Chernobyl Project revealed that there is a need for such a closely linked group when the Member State lacks sufficient technical resource to independently perform an assessment of environmental contamination following an accidental release of radioactivity. The existence of such a network of laboratories would help to assure responsible government representatives and the general public that the Agency has additional available resources including specialized experts to perform assessments on which to base required actions for many accident scenarios and their radiological consequences. The purpose of the present Consultants' Meeting is to discuss the organization and scope of the proposed network of analytical laboratories. The Consultants should discuss the matrices and nuclides of interest at various time frames of an accidental release of radioactivity. It is also intended that the Consultants should discuss the laboratories from their experience which would have the specialized expertise needed, in both terrestrial and aquatic sample collection and analysis. Finally, it is intended that the Consultants should discuss whether it would be desirable for the Agency to produce a technical document based on the achievements of the Agency programme on 'Rapid Instrumental and Separation Methods for Monitoring Radionuclides in Food and Environmental Samples'. A Guide Book was considered essential by the participants of this Co-ordinated Research Programme because it would be a succinct form and on a common

  13. Environment

    DEFF Research Database (Denmark)

    Valentini, Chiara

    2017-01-01

    The term environment refers to the internal and external context in which organizations operate. For some scholars, environment is defined as an arrangement of political, economic, social and cultural factors existing in a given context that have an impact on organizational processes and structures....... For others, environment is a generic term describing a large variety of stakeholders and how these interact and act upon organizations. Organizations and their environment are mutually interdependent and organizational communications are highly affected by the environment. This entry examines the origin...... and development of organization-environment interdependence, the nature of the concept of environment and its relevance for communication scholarships and activities....

  14. Near Real Time Structural Health Monitoring with Multiple Sensors in a Cloud Environment

    Science.gov (United States)

    Bock, Y.; Todd, M.; Kuester, F.; Goldberg, D.; Lo, E.; Maher, R.

    2017-12-01

    A repeated near real time 3-D digital surrogate representation of critical engineered structures can be used to provide actionable data on subtle time-varying displacements in support of disaster resiliency. We describe a damage monitoring system of optimally-integrated complementary sensors, including Global Navigation Satellite Systems (GNSS), Micro-Electro-Mechanical Systems (MEMS) accelerometers coupled with the GNSS (seismogeodesy), light multi-rotor Unmanned Aerial Vehicles (UAVs) equipped with high-resolution digital cameras and GNSS/IMU, and ground-based Light Detection and Ranging (LIDAR). The seismogeodetic system provides point measurements of static and dynamic displacements and seismic velocities of the structure. The GNSS ties the UAV and LIDAR imagery to an absolute reference frame with respect to survey stations in the vicinity of the structure to isolate the building response to ground motions. The GNSS/IMU can also estimate the trajectory of the UAV with respect to the absolute reference frame. With these constraints, multiple UAVs and LIDAR images can provide 4-D displacements of thousands of points on the structure. The UAV systematically circumnavigates the target structure, collecting high-resolution image data, while the ground LIDAR scans the structure from different perspectives to create a detailed baseline 3-D reference model. UAV- and LIDAR-based imaging can subsequently be repeated after extreme events, or after long time intervals, to assess before and after conditions. The unique challenge is that disaster environments are often highly dynamic, resulting in rapidly evolving, spatio-temporal data assets with the need for near real time access to the available data and the tools to translate these data into decisions. The seismogeodetic analysis has already been demonstrated in the NASA AIST Managed Cloud Environment (AMCE) designed to manage large NASA Earth Observation data projects on Amazon Web Services (AWS). The Cloud provides

  15. Monitoring the Impact of Anthropogenic and Natural Influences on the Environment of Mesoamerica

    Science.gov (United States)

    Hardin, D.; Graves, S.; Sever, T.; Irwin, D.

    2005-12-01

    Mesoamerica - composed of the seven Central American countries and the five southernmost states of Mexico - is one of the richest biological regions in the world. The region is home to approximately eight percent of the planet's biodiversity. There are 14 biosphere reserves, eight world heritage sites and 589 protected areas. The human population, of over 45 million people consists of more than 50 ethnic groups. This rich biological and cultural diversity is threatened by human influence and natural disasters. Illegal logging and slash and burn agriculture are major contributors to extensive deforestation. Earthquakes, volcanoes, drought, and severe storms threaten the region. Of particular note is the massive destruction and loss of life resulting from hurricane Mitch in 1998. An international effort is underway to preserve the remaining forested regions, with its biodiversity, and to promote sustained development throughout the region. In 2002 the National Aeronautics and Space Administration (NASA) joined with the World Bank and the United States Agency for International Development (USAID) to work with the Central American Commission for Environment and Development (CCAD), to develop an advanced decision support system for Mesoamerica known as SERVIR. (SERVIR is a Spanish acronym meaning to serve.) The partners are contributing expertise in space-based observation with information management technologies and intimate knowledge of local ecosystems to create a system for use by scientists, educators, and policy makers to monitor and forecast ecological changes, respond to natural disasters, and better understand both natural and human induced effects. NASA/Marshall Space Flight Center and the University of Alabama in Huntsville (UAH) are concentrating on the preparation of data products and Information Technology applications that will integrate information from the entire region into a coherent information system that is easy to access and utilize. Already

  16. Annual report on radioactive discharges from Winfrith and monitoring the environment 1990

    International Nuclear Information System (INIS)

    1991-06-01

    This annual report, the sixth of its type, aims to provide full information on discharges and environmental monitoring. The report is mainly graphical, comparing past and current levels with authorised limits, derived limits or the recommended limits of the International Commission on Radiological Protection (ICRP). All the data are presented at the end of the report in tabular form. Discharges from Winfrith are subject to Authorisations issued jointly by the Department of the Environment (DOE) and the Ministry of Agriculture, Fisheries and Food (MAFF). The numerical values of the Authorised Limits are based on past performance, future requirements and the application of Best Practicable Means (BPM). As a ''back stop'', discharges at the limits must not result in doses to the most potentially exposed part of the local population - the critical group - exceeding 0.5 mSv per year. The limit recommended by the International Commission on Radiological Protection (ICRP) for dose to a member of the general public is 1.0 mSv per year. In September 1990 Winfrith's Steam Generating Heavy Water Reactor (SGHWR) was shut down and a decision taken, later, that reactor operation would cease. The pattern of discharges thus changed in the last quarter of the year and discharges in future will be lower, and of a different pattern, than those of the past twenty years. The dose to the critical group, which is already less than 2% of the ICRP limit and less than 1% of the UK average natural background dose will drop further in future years. (Author)

  17. Organophosphorus pollutants (OPP) in aquatic environment at Damietta Governorate, Egypt: implications for monitoring and biomarker responses.

    Science.gov (United States)

    Abdel-Halim, K Y; Salama, A K; El-Khateeb, E N; Bakry, N M

    2006-06-01

    The study was carried out from spring 1999 to spring 2001 to monitor the residue levels of organophosphorus pollutants (OPP) in aquatic environment of the drainage canal surrounding a pesticide factory at Damietta Governorate. Water, sediment, and fish samples were collected at six different seasonal periods. OPPs were analyzed by GLC and confirmed using GC-MS. Chlorpyrifos, chlorpyrifos-methyl, malathion, diazinon, pirimiphos-methyl and profenofos were detected in most samples. Chlorpyrifos was dominant in all water and sediment samples. It was ranged from 24.5 to 303.8 and 0.9 to 303.8 ppb in water and sediment samples, respectively. Diazinon level was slightly similar to chlorpyrifos in fish samples. Data based on the grand total concentration of OPP showed that the most polluted samples were collected either at spring 1999 or autumn 2000. They were 675.5 and 303.8 ppb in water samples and 43.0 and 52.2 ppb in fish collected at spring 1999 and autumn 2000, respectively. The obtained results are in parallel to that found in case of cholinesterase activity where the activity of both acetylcholinesterase (AChE) and butyrylcholinesterase (BuChE) was declined at these seasonal period. The activity levels of AChE and BuChE were found to be 77.18% and 59.67% of control at spring 1999 and 78.62% and 85.80% of control, at autumn 2000, respectively. Thus, AChE and BuChE could be used as biomarkers for tracing and biomonitoring OPP pollution.

  18. Developing the remote sensing-based water environmental model for monitoring alpine river water environment over Plateau cold zone

    Science.gov (United States)

    You, Y.; Wang, S.; Yang, Q.; Shen, M.; Chen, G.

    2017-12-01

    Alpine river water environment on the Plateau (such as Tibetan Plateau, China) is a key indicator for water security and environmental security in China. Due to the complex terrain and various surface eco-environment, it is a very difficult to monitor the water environment over the complex land surface of the plateau. The increasing availability of remote sensing techniques with appropriate spatiotemporal resolutions, broad coverage and low costs allows for effective monitoring river water environment on the Plateau, particularly in remote and inaccessible areas where are lack of in situ observations. In this study, we propose a remote sense-based monitoring model by using multi-platform remote sensing data for monitoring alpine river environment. In this study some parameterization methodologies based on satellite remote sensing data and field observations have been proposed for monitoring the water environmental parameters (including chlorophyll-a concentration (Chl-a), water turbidity (WT) or water clarity (SD), total nitrogen (TN), total phosphorus (TP), and total organic carbon (TOC)) over the china's southwest highland rivers, such as the Brahmaputra. First, because most sensors do not collect multiple observations of a target in a single pass, data from multiple orbits or acquisition times may be used, and varying atmospheric and irradiance effects must be reconciled. So based on various types of satellite data, at first we developed the techniques of multi-sensor data correction, atmospheric correction. Second, we also built the inversion spectral database derived from long-term remote sensing data and field sampling data. Then we have studied and developed a high-precision inversion model over the southwest highland river backed by inversion spectral database through using the techniques of multi-sensor remote sensing information optimization and collaboration. Third, take the middle reaches of the Brahmaputra river as the study area, we validated the key

  19. Remote monitoring of the environment on boundary of the Azerbaijan Republic

    International Nuclear Information System (INIS)

    Pashayev, A.M.; Bayramov, A.A.; Mehdiev, A.Sh.

    2002-01-01

    The project of the automated remote monitoring for a level of an environment background radiation in settlements along boundary of the Azerbaijan Republic, and also along eastern suburbs occupied Azerbaijan Republic regions by Armenia's army is developed. The main purpose of the project is: Increase of a level of a radiation safety on territory of the Azerbaijan Republic; Controlling of a level of an environment background radiation on boundary of the Azerbaijan Republic with the purpose of well-timed warning and acceptance of indispensable measures at probable emergencies on Atomic Power Stations in a number adjacent from Azerbaijan countries, or other ecological catastrophes; Controlling of a level of an environment background radiation along eastern suburbs of Azerbaijan regions occupied of Armenia's army and detection of the facts of wrongful disposals of atomic engineering of Armenia on territory of Azerbaijan. As is known, in a number adjacent from Azerbaijan countries the nuclear industry is advanced or develops. It has resulted in origin of threat of a radiation hazard in case of ecological catastrophes: widely scale leakage of radioactive wastes, explosions, or fires on nuclear generating sets, acts of sabotage, directional against Azerbaijan. In this case, at unfavorable meteorological conditions a radioactive waste may be brought by a wind or a rain on territory of Azerbaijan. For example, the atomic power station constructs intensively in Islamic Republic Iran (IRI). It is necessary to estimate an initial background radiation along southern boundaries of Azerbaijan, that to determine probable changes in an ecology of southern boundaries during regular maintenance of atomic power station. Other example. In the Armenian Republic the atomic power station acts, which one is the padding center of a heightened radiation hazard in the Caucasian region. It is stipulated by several reasons: territory of Armenian Republic is heightened seismic activity, therefore

  20. Roshydromet system of environment radioactive contamination monitoring in the Arctic region of Russia

    International Nuclear Information System (INIS)

    Chelukanov, V.

    1995-01-01

    159 arctic hydrometerological stations take measurements of gamma radiation. 51 stations monitor the density of atmospheric radioactive fallout and 12 stations monitor the concentration of aerosols. 13 hydrological stations sited in the mouths of main Arctic Ocean rivers take water samples. Regional laboratories carry out isotop analysis of samples. Information on high levels of a radioactivity measured at the monitoring stations, as well as information on abnormal radioactivity from regional laboratories are transmitted to the Information Centers on the monitoring system (Moscow and Obnisk) by cable. 2 figs., 1 tab

  1. Technical note: Evaluation of standard ultraviolet absorption ozone monitors in a polluted urban environment

    Directory of Open Access Journals (Sweden)

    E. J. Dunlea

    2006-01-01

    Full Text Available The performance of the EPA Federal Equivalent Method (FEM technique for monitoring ambient concentrations of O3 via ultraviolet absorption (UV has been evaluated using data from the Mexico City Metropolitan Area field campaign (MCMA-2003. Comparisons of UV O3 monitors with open path Differential Optical Absorption Spectroscopy (DOAS and open path Fourier Transform Infrared (FTIR spectroscopy instruments in two locations revealed average discrepancies in the measured concentrations between +13% to −18%. Good agreement of two separate open path DOAS measurements at one location indicated that spatial and temporal inhomogeneities were not substantially influencing comparisons of the point sampling and open path instruments. The poor agreement between the UV O3 monitors and the open path instruments was attributed to incorrect calibration factors for the UV monitors, although interferences could not be completely ruled out. Applying a linear correction to these calibration factors results in excellent agreement of the UV O3 monitors with the co-located open path measurements; regression slopes of 0.94 to 1.04 and associated R2 values of >0.89. A third UV O3 monitor suffered from large spurious interferences, which were attributed to extinction of UV radiation within the monitor by fine particles (3 monitors and recommendations for future testing are made.

  2. Unmanned aerial complexes as a way of NPP and environment radiation monitoring

    International Nuclear Information System (INIS)

    Babak, V.P.; Kanchenko, V.A.; Klyuchnikov, A.A.; Krasnov, V.A.; Chepur, N.L.

    2012-01-01

    As a example of the using of unmanned aircraft for video monitoring and radiation background measurement in the accident area at the NPP Fukushima -1 are shown the efficiency of its use. The analyse of possible environmental monitoring remotely piloted ultralight unmanned aerial vehicle are carried out

  3. Remote Monitoring of Post-eruption Volcano Environment Based-On Wireless Sensor Network (WSN): The Mount Sinabung Case

    Science.gov (United States)

    Soeharwinto; Sinulingga, Emerson; Siregar, Baihaqi

    2017-01-01

    An accurate information can be useful for authorities to make good policies for preventive and mitigation after volcano eruption disaster. Monitoring of environmental parameters of post-eruption volcano provides an important information for authorities. Such monitoring system can be develop using the Wireless Network Sensor technology. Many application has been developed using the Wireless Sensor Network technology, such as floods early warning system, sun radiation mapping, and watershed monitoring. This paper describes the implementation of a remote environment monitoring system of mount Sinabung post-eruption. The system monitor three environmental parameters: soil condition, water quality and air quality (outdoor). Motes equipped with proper sensors, as components of the monitoring system placed in sample locations. The measured value from the sensors periodically sends to data server using 3G/GPRS communication module. The data can be downloaded by the user for further analysis.The measurement and data analysis results generally indicate that the environmental parameters in the range of normal/standard condition. The sample locations are safe for living and suitable for cultivation, but awareness is strictly required due to the uncertainty of Sinabung status.

  4. Consideration of tidal influences in determining measurement periods when monitoring built-environment radon levels

    International Nuclear Information System (INIS)

    Crockett, R.G.M.; Phillips, P.S.; Gillmore, G.K.; Denman, A.R.; Groves-Kirkby, C.J.

    2006-01-01

    Using three hourly-sampling continuous radon monitors, deployed at separate locations in and around the town of Northampton, UK, during the period May 2002 to September 2005, evidence has been identified of tidal influences on built environment radon levels. The data-sets from these deployments, together with additional data-sets collected from a house in Devon, UK, over the period May 1994 to October 1996, and made available by the UK Building Research Establishment, have been analysed using a number of analytical techniques, including a novel correlation technique developed during the investigation. Radon concentration levels in all of the investigated sites exhibit cyclic variation with a period of approximately 14-15 days, equivalent to the spring-tide interval, and lag the corresponding new and full moons by varying periods. The tide/radon lag interval for the two public-sector buildings changes abruptly in September/October, indicating that a significant characteristic of these buildings changes at this time. For domestic properties, the lag is relatively unchanged during the year, but is greater in Devon, in the South-West of England, than in Northampton, in the English East Midlands. These differences are attributed to location relative to coastlines (the South-West experiences greater tidal-loading than the Midlands), underlying geology and rock/soil hydration. Depending on its position within the local 14 to 15-day tidally-induced radon cycle, an individual 7-day radon measurement may yield an erroneous estimate of longer term average levels, up to 46% higher or lower than the average level for one of the reported data-sets. Thus a building with a mean radon concentration below the local Action Level could appear to be unsafe if measured around a tidal-cyclic radon maximum: conversely, a building with a mean radon concentration above the Action Level could appear to be safe when measured around a tidal-cyclic radon minimum. A minimum radon

  5. Development of a fluorescent antibody method for the detection of Enterococcus faecium and its potential for coastal aquatic environment monitoring.

    Science.gov (United States)

    Caruso, Gabriella; Monticelli, L S; Caruso, R; Bergamasco, A

    2008-02-01

    A direct, microscopic fluorescent antibody method was developed to detect the occurrence of Enterococcus faecium in coastal aquatic environments and was compared with the conventional membrane filtering method. The "in situ" application of the antibody-based protocol in the analysis of water samples collected from coastal polyhaline habitats demonstrated good sensitivity and ease of implementation. Data obtained with the microscopic technique were in agreement with those obtained from culture counts. The fluorescent antibody method proved to be a rapid and reliable technique for the detection of E. faecium. The advantages and limitations intrinsic to the method are discussed, highlighting the potential of this new technique for monitoring coastal aquatic environments.

  6. Availability of mollusks as ''biological monitor'' to monitoring of the long-lived silver isotope released into the marine environment

    International Nuclear Information System (INIS)

    Watabe, Teruhisa; Yokosuka, Setsuko; Kurosawa, Akiko

    2003-01-01

    The species of mollusks often show unique physiological properties and the elemental composition different from those of fishes as observed in the blood constituents. Much higher concentrations of metal elements such as cupper, zinc, cadmium and so on have been reported for squids and bivalves than other organisms. The present study reports the results of gamma spectrometry analyses for two species of gastropods (Buccinum isaotakii and Buccinum striatissimum), one of the important species of mollusks, inhabiting on the sea bottom at the depth of some hundreds meters off the coast and for squids (Todarodes pacificus, Thysanoteuthis rhombus, etc.) landed at several fishing ports in Japan. It would be noted that 108m Ag (half-life time: 418.21y) was commonly detected in the viscera of both gastropods and squids usually at the radioactivity level higher than 137 Cs. A discussion on the distribution and inventory of 108m Ag in the water column was attempted on the basis of the data on its specific activity, which was derived from the data on stable silver for the samples of interest obtained by analyses using ICP-AES. Special attention was directed to the efficacy and applicability of the mollusks having an affinity for this element to the environmental monitoring as indices. (author)

  7. A Novel Method To On-Line Monitor Reactor Nuclear Power And In-Core Thermal Environments

    International Nuclear Information System (INIS)

    Liu, Hanying; Miller, Don W.; Li, Dongxu; Radcliff, Thomas D.

    2002-01-01

    For current nuclear power plants, nuclear power can not be directly measured and in-core fuel thermal environments can not be monitored due to the unavailability of an appropriate measurement technology and the inaccessibility of the fuel. If the nuclear deposited power and the in-core thermal conditions (i.e. fuel or coolant temperature and heat transfer coefficient) can be monitored in-situ, then it would play a valuable and critical role in increasing nuclear power, predicting abnormal reactor operation, improving core physical models and reducing core thermal margin so as to implement higher fuel burn-up. Furthermore, the management of core thermal margin and fuel operation may be easier during reactor operation, post-accident or spent fuel storage. On the other hand, for some advanced Generation IV reactors, the sealed and long-lived reactor core design challenges traditional measurement techniques while conventional ex-core detectors and current in-core detectors can not monitor details of the in-core fuel conditions. A method is introduced in this paper that responds to the challenge to measure nuclear power and to monitor the in-core thermal environments, for example, local fuel pin or coolant heat convection coefficient and temperature. In summary, the method, which has been designed for online in-core measurement and surveillance, will be beneficial to advanced plant safety, efficiency and economics by decreasing thermal margin or increasing nuclear power. The method was originally developed for a constant temperature power sensor (CTPS). The CTPS is undergoing design and development for an advanced reactor core to measure in-core nuclear power in measurement mode and to monitor thermal environments in compensation mode. The sensor dynamics was analyzed in compensation mode to determine the environmental temperature and the heat transfer coefficient. Previous research demonstrated that a first order dynamic model is not sufficient to simulate sensor

  8. Monitoring the impact of trade agreements on national food environments: trade imports and population nutrition risks in Fiji.

    Science.gov (United States)

    Ravuvu, Amerita; Friel, Sharon; Thow, Anne-Marie; Snowdon, Wendy; Wate, Jillian

    2017-06-13

    Trade agreements are increasingly recognised as playing an influential role in shaping national food environments and the availability and nutritional quality of the food supply. Global monitoring of food environments and trade policies can strengthen the evidence base for the impact of trade policy on nutrition, and support improved policy coherence. Using the INFORMAS trade monitoring protocol, we reviewed available food supply data to understand associations between Fiji's commitments under WTO trade agreements and food import volume trends. First, a desk review was conducted to map and record in one place Fiji's commitments to relevant existing trade agreements that have implications for Fiji's national food environment under the domains of the INFORMAS trade monitoring protocol. An excel database was developed to document the agreements and their provisions. The second aspect of the research focused on data extraction. We began with identifying food import volumes into Fiji by country of origin, with a particular focus on a select number of 'healthy and unhealthy' foods. We also developed a detailed listing of transnational food corporations currently operating in Fiji. The study suggests that Fiji's WTO membership, in conjunction with associated economic and agricultural policy changes have contributed to increased availability of both healthy and less healthy imported foods. In systematically monitoring the import volume trends of these two categories of food, the study highlights an increase in healthy foods such as fresh fruits and vegetables and whole-grain refined cereals. The study also shows that there has been an increase in less healthy foods including fats and oils; meat; processed dairy products; energy-dense beverages; and processed and packaged foods. By monitoring the trends of imported foods at country level from the perspective of trade agreements, we are able to develop appropriate and targeted interventions to improve diets and health. This

  9. Quantification of differences between occupancy and total monitoring periods for better assessment of exposure to particles in indoor environments

    Science.gov (United States)

    Wierzbicka, A.; Bohgard, M.; Pagels, J. H.; Dahl, A.; Löndahl, J.; Hussein, T.; Swietlicki, E.; Gudmundsson, A.

    2015-04-01

    For the assessment of personal exposure, information about the concentration of pollutants when people are in given indoor environments (occupancy time) are of prime importance. However this kind of data frequently is not reported. The aim of this study was to assess differences in particle characteristics between occupancy time and the total monitoring period, with the latter being the most frequently used averaging time in the published data. Seven indoor environments were selected in Sweden and Finland: an apartment, two houses, two schools, a supermarket, and a restaurant. They were assessed for particle number and mass concentrations and number size distributions. The measurements using a Scanning Mobility Particle Sizer and two photometers were conducted for seven consecutive days during winter in each location. Particle concentrations in residences and schools were, as expected, the highest during occupancy time. In the apartment average and median PM2.5 mass concentrations during the occupancy time were 29% and 17% higher, respectively compared to total monitoring period. In both schools, the average and medium values of the PM2.5 mass concentrations were on average higher during teaching hours compared to the total monitoring period by 16% and 32%, respectively. When it comes to particle number concentrations (PNC), in the apartment during occupancy, the average and median values were 33% and 58% higher, respectively than during the total monitoring period. In both houses and schools the average and median PNC were similar for the occupancy and total monitoring periods. General conclusions on the basis of measurements in the limited number of indoor environments cannot be drawn. However the results confirm a strong dependence on type and frequency of indoor activities that generate particles and site specificity. The results also indicate that the exclusion of data series during non-occupancy periods can improve the estimates of particle concentrations and

  10. Coal conversion and aquatic environments: overview of impacts and strategies for monitoring. Environmental Sciences Division publication No. 1112

    Energy Technology Data Exchange (ETDEWEB)

    Roop, R. D.; Sanders, F. S.; Barnthouse, L. W.

    1977-01-01

    Impact assessment and environmental monitoring are difficult but crucial steps needed to ensure the environmentally safe development of coal conversion technologies. This paper summarizes strategies for impact assessment and monitoring developed at Oak Ridge National Laboratory for DOE's program to build demonstration facilities. Impacts on aquatic environments depend heavily on the abiotic and biotic characteristics of the site and details of facility design. Key issues include availability of water, use of ''zero-discharge'' designs, and methods of handling solid wastes. In monitoring programs emphasis is placed on (1) thorough use of existing data, (2) use of a synoptic reconnaissance survey, criteria for choosing parameters to be measured, and the search for ecologically meaningful, cost-effective methods.

  11. Remote sensing of gene expression in Planta: transgenic plants as monitors of exogenous stress perception in extraterrestrial environments

    Science.gov (United States)

    Manak, Michael S.; Paul, Anna-Lisa; Sehnke, Paul C.; Ferl, Robert J.

    2002-01-01

    Transgenic arabidopsis plants containing the alcohol dehydrogenase (Adh) gene promoter fused to the green fluorescent protein (GFP) reporter gene were developed as biological sensors for monitoring physiological responses to unique environments. Plants were monitored in vivo during exposure to hypoxia, high salt, cold, and abcissic acid in experiments designed to characterize the utility and responses of the Adh/GFP biosensors. Plants in the presence of environmental stimuli that induced the Adh promoter responded by expressing GFP, which in turn generated a detectable fluorescent signal. The GFP signal degraded when the inducing stimulus was removed. Digital imaging of the Adh/GFP plants exposed to each of the exogenous stresses demonstrated that the stress-induced gene expression could be followed in real time. The experimental results established the feasibility of using a digital monitoring system for collecting gene expression data in real time from Transgenic Arabidopsis Gene Expression System (TAGES) biosensor plants during space exploration experiments.

  12. Stigmergy-based Long-Term Monitoring of Indoor Users Mobility in Ambient Assisted Living Environments: the DOREMI Project Approach

    OpenAIRE

    Palumbo, Filippo; La Rosa, Davide; Ferro, Erina

    2016-01-01

    Aging trends in Europe motivate the need for technological solutions aimed at preventing the main causes of morbidity and premature mortality. In this framework, the DOREMI project addresses three important causes of morbidity and mortality in the elderly by devising an ICT-based home care services for aging people to contrast cognitive decline, sedentariness and unhealthy dietary habits. In DOREMI, the house itself is transformed in an unobtrusive monitoring environment able to keep track of...

  13. Quality of environment monitoring: which approach to build up with local actors? ANCLI/IRSN meeting on March 24, 2004

    International Nuclear Information System (INIS)

    2004-01-01

    This report presents and discusses the main conclusions of a survey performed among the Information Local Commission (CLIs) and the French Radioprotection and Nuclear Safety Institute (IRSN) in order to know their expectations as far the control of the environment and the monitoring of releases by nuclear installations are concerned. It also reports discussions which occurred during the presentation of these results during a meeting at Ville d'Avray

  14. Significance of Operating Environment in Condition Monitoring of Large Civil Structures

    Directory of Open Access Journals (Sweden)

    Sreenivas Alampalli

    1999-01-01

    Full Text Available Success of remote long-term condition monitoring of large civil structures and developing calibrated analytical models for damage detection, depend significantly on establishing accurate baseline signatures and their sensitivity. Most studies reported in the literature concentrated on the effect of structural damage on modal parameters without emphasis on reliability of modal parameters. Thus, a field bridge structure was studied for the significance of operating conditions in relation to baseline signatures. Results indicate that in practice, civil structures should be monitored for at least one full cycle of in-service environmental changes before establishing baselines for condition monitoring or calibrating finite-element models. Boundary conditions deserve special attention.

  15. Nuclear Power Plant environment`s surveillance by satellite remote sensing and in-situ monitoring data

    Science.gov (United States)

    Zoran, Maria

    The main environmental issues affecting the broad acceptability of nuclear power plant are the emission of radioactive materials, the generation of radioactive waste, and the potential for nuclear accidents. All nuclear fission reactors, regardless of design, location, operator or regulator, have the potential to undergo catastrophic accidents involving loss of control of the reactor core, failure of safety systems and subsequent widespread fallout of hazardous fission products. Risk is the mathematical product of probability and consequences, so lowprobability and high-consequence accidents, by definition, have a high risk. NPP environment surveillance is a very important task in frame of risk assessment. Satellite remote sensing data had been applied for dosimeter levels first time for Chernobyl NPP accident in 1986. Just for a normal functioning of a nuclear power plant, multitemporal and multispectral satellite data in complementarily with field data are very useful tools for NPP environment surveillance and risk assessment. Satellite remote sensing is used as an important technology to help environmental research to support research analysis of spatio-temporal dynamics of environmental features nearby nuclear facilities. Digital processing techniques applied to several LANDSAT, MODIS and QuickBird data in synergy with in-situ data are used to assess the extent and magnitude of radiation and non-radiation effects on the water, near field soil, vegetation and air. As a test case the methodology was applied for for Nuclear Power Plant (NPP) Cernavoda, Romania. Thermal discharge from nuclear reactors cooling is dissipated as waste heat in Danube-Black -Sea Canal and Danube River. Water temperatures captured in thermal IR imagery are correlated with meteorological parameters. If during the winter thermal plume is localized to an area of a few km of NPP, the temperature difference between the plume and non-plume areas being about 1.5 oC, during summer and fall , is

  16. Configuration Management and Infrastructure Monitoring Using CFEngine and Icinga for Real-time Heterogeneous Data Taking Environment

    Science.gov (United States)

    Poat, M. D.; Lauret, J.; Betts, W.

    2015-12-01

    The STAR online computing environment is an intensive ever-growing system used for real-time data collection and analysis. Composed of heterogeneous and sometimes groups of custom-tuned machines, the computing infrastructure was previously managed by manual configurations and inconsistently monitored by a combination of tools. This situation led to configuration inconsistency and an overload of repetitive tasks along with lackluster communication between personnel and machines. Globally securing this heterogeneous cyberinfrastructure was tedious at best and an agile, policy-driven system ensuring consistency, was pursued. Three configuration management tools, Chef, Puppet, and CFEngine have been compared in reliability, versatility and performance along with a comparison of infrastructure monitoring tools Nagios and Icinga. STAR has selected the CFEngine configuration management tool and the Icinga infrastructure monitoring system leading to a versatile and sustainable solution. By leveraging these two tools STAR can now swiftly upgrade and modify the environment to its needs with ease as well as promptly react to cyber-security requests. By creating a sustainable long term monitoring solution, the detection of failures was reduced from days to minutes, allowing rapid actions before the issues become dire problems, potentially causing loss of precious experimental data or uptime.

  17. WildSense: Monitoring Interactions among Wild Deer in Harsh Outdoor Environments Using a Delay-Tolerant WSN

    Directory of Open Access Journals (Sweden)

    Junho Ahn

    2016-01-01

    Full Text Available Biologists and ecologists often monitor the spread of disease among deer in the wild by using tracking systems that record their movement patterns, locations, and interaction behavior. The existing commercial systems for monitoring wild deer utilize collars with GPS sensors, deployed on captured and rereleased deer. The GPS sensors record location data every few hours, enabling researchers to approximate the interaction behavior of tracked deer with their GPS locations. However, the coarse granularity of periodically recorded GPS location data provides only limited precision for determining deer interaction behavior. We have designed a novel system to monitor wild deer interaction behavior more precisely in harsh wilderness environments. Our system combines the functionalities of both GPS and RF-radio sensors with low-cost and minimal-resource motes. We designed and built our system to be able to operate robustly for a period of up to several months for continual tracking and monitoring of the locations and interaction behaviors of wild deer in harsh environments. We successfully deployed six deer collars on six wild deer that were captured and rereleased in the Soapstone Prairie Natural Area of northern Colorado over a one-month period. In this paper, we describe how we designed and built this system and evaluate its successful operation in a wilderness area.

  18. Tesla VUPJT instruments for radiation monitoring of working environment and selected aplications

    International Nuclear Information System (INIS)

    Slezak, V.; Kula, J.; Novakova, O.; Jursova, L.; Severa, L.

    1986-01-01

    A survey is presented of the current state of development and production of instruments for ionizing radiation monitoring and detection, also listing possible applications in the national economy. (author)

  19. Monitoring heat and humid air emissions in the environment of large power plants

    International Nuclear Information System (INIS)

    Haessler, G.

    1976-01-01

    Environmental monitoring systems are installed for site evaluation purposes, the confirmation of predictions, to secure evidence, assess damage, for research and development purposes and in order to evaluate plant performance. (orig./RW) [de

  20. Person × Environment Interactions on Adolescent Delinquency: Sensation Seeking, Peer Deviance and Parental Monitoring.

    Science.gov (United States)

    Mann, Frank D; Kretsch, Natalie; Tackett, Jennifer L; Harden, K Paige; Tucker-Drob, Elliot M

    2015-04-01

    Sensation seeking is a personality trait that is robustly correlated with delinquent behavior in adolescence. The current study tested specific contextual factors hypothesized to facilitate, exacerbate or attenuate this risk factor for adolescent delinquency. Individual differences in sensation seeking, peer deviance, parental monitoring and self-reported delinquent behavior were assessed in a sample of 470 adolescents. Peer deviance partially mediated the effects of sensation seeking and parental monitoring on adolescent delinquency. We also found evidence for a three-way interaction between sensation seeking, peer deviance and parental monitoring, such that the highest rates of delinquency occurred from the concurrence of high sensation seeking, high peer deviance, and low levels of parental monitoring. Results highlight the importance of considering peer- and family-level processes when evaluating personality risk and problematic adolescent behavior.

  1. Annual report on radioactive discharges and monitoring of the environment 1988

    International Nuclear Information System (INIS)

    1989-01-01

    This report supplements BNFL's Health and Safety Annual Report and lists 1988 discharges and environmental monitoring for the following sites: Sellafield, Chapelcross, Drigg Storage and Disposal Site, Springfields Works, Capenhurst Works. (UK)

  2. Certified reference materials for organic contaminants for use in monitoring of the aquatic environment

    NARCIS (Netherlands)

    Boer, de J.; McGovern, E.

    2001-01-01

    Over the last three decades organic contaminants have been of increasing importance in environmental monitoring. Dioxins, furans, polychlorinated biphenyls and organochlorine pesticides have determined the environmental research agenda. This has led to an increasing demand for certified reference

  3. Monitoring Microbes in the Spacecraft Environment by Mass Spectrometry of Ribosomal RNA, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The unique stresses in the spacecraft environment including isolation, containment, weightlessness, increased radiation exposure, and enhanced microbial...

  4. Monitoring of radioactivity in the UK environment: an annotated bibliography of current programmes

    International Nuclear Information System (INIS)

    Cotter, A.J.R.; Hunt, G.J.

    1992-01-01

    In the UK, many organisations carry out regular radioactivity monitoring programmes, and summaries of these programmes have been published in 1983 and 1988. The number of organisations carrying out radioactivity monitoring has increased rapidly in recent years, particularly in the local authority sector. The present report updates the previous summarises in the form of an annotated bibliography, giving synopses of all regular UK programmes whose results are published in report form. (author)

  5. SEM based overlay measurement between resist and buried patterns

    Science.gov (United States)

    Inoue, Osamu; Okagawa, Yutaka; Hasumi, Kazuhisa; Shao, Chuanyu; Leray, Philippe; Lorusso, Gian; Baudemprez, Bart

    2016-03-01

    With the continuous shrink in pattern size and increased density, overlay control has become one of the most critical issues in semiconductor manufacturing. Recently, SEM based overlay of AEI (After Etch Inspection) wafer has been used for reference and optimization of optical overlay (both Image Based Overlay (IBO) and Diffraction Based Overlay (DBO)). Overlay measurement at AEI stage contributes monitor and forecast the yield after formation by etch and calibrate optical measurement tools. however those overlay value seems difficult directly for feedback to a scanner. Therefore, there is a clear need to have SEM based overlay measurements of ADI (After Develop Inspection) wafers in order to serve as reference for optical overlay and make necessary corrections before wafers go to etch. Furthermore, to make the corrections as accurate as possible, actual device like feature dimensions need to be measured post ADI. This device size measurement is very unique feature of CDSEM , which can be measured with smaller area. This is currently possible only with the CD-SEM. This device size measurement is very unique feature of CD-SEM , which can be measured with smaller area. In this study, we assess SEM based overlay measurement of ADI and AEI wafer by using a sample from an N10 process flow. First, we demonstrate SEM based overlay performance at AEI by using dual damascene process for Via 0 (V0) and metal 1 (M1) layer. We also discuss the overlay measurements between litho-etch-litho stages of a triple patterned M1 layer and double pattern V0. Second, to illustrate the complexities in image acquisition and measurement we will measure overlay between M1B resist and buried M1A-Hard mask trench. Finally, we will show how high accelerating voltage can detect buried pattern information by BSE (Back Scattering Electron). In this paper we discuss the merits of this method versus standard optical metrology based corrections.

  6. Environmental survey near a decommissioning nuclear facility: example of tritium monitoring in the terrestrial environment of Creys-Malville - Environmental survey near a nuclear facility undergoing decommissioning: example of tritium monitoring in the terrestrial environment of Creys-Malville

    Energy Technology Data Exchange (ETDEWEB)

    Boyer, C.; Gontier, G.; Chauveau, J.L. [EDF CIDEN, Division Environnement, 154 Avenue Thiers, 69458 Lyon (France); Pourcelot, L.; Roussel-Debet, S.; Cossonnet, P.C. [IRSN, LERCM Cadarache and LMRE Orsay (France); Jean-Baptiste, P. [LSCE, UMR 1572-CEA/CNRS/UVQS, 91198 Gif sur Yvette (France)

    2014-07-01

    As part of the regulatory environmental monitoring around its nuclear power plants (NPP) in France, EDF carries out more than 40.000 measurements of radionuclides in the environment every year. In addition, EDF performs more detailed radioecological surveys on all of its sites. The purposes of these surveys are: 1/ to control that radioactive discharge limits prescribed by the regulatory authority are respected, 2/ to monitor the environment of the NPPs to verify normal plant operation and to detect all possible failures in power station operation at an early stage and 3/ to establish if there is any increase of radionuclides of anthropogenic origin in the environment and to determine whether this build-up can be attributed to plant operations. Radioecological surveys are conducted in the environment surrounding each of EDF's NPPs. Samples are collected in surrounding ecosystems (terrestrial and aquatic) where the radioactive releases are discharged (liquid and gaseous discharges). These surveys results enable the examination of the spatial distribution and temporal variability of radionuclide activity in the environment throughout the reactors life, from the first fuel load to the decommissioning of the plant. The results from this monitoring have shown that EDF's nuclear power plants have only a minor effect on radionuclide levels in the environment. These results highlight the efficiency of EDF's efforts to minimise its impacts on the environment via an efficient waste management system and high operating standards of its plants. In particular, tritium is subject to special monitoring for more than 30 years; concentrations of free tritium and organically bound tritium in major environmental compartments are therefore well-known in the vicinity of French NPPs. At the end of a reactor's life, EDF has collected a large amount of reference data before decommissioning operations start. During these operations, EDF pursue the radioecological survey

  7. Monitoring of radiation in the environment in the Netherlands. Results in 2002

    NARCIS (Netherlands)

    Knetsch GJ; RIZA; RIKZ; KvW; LSO; IMD

    2004-01-01

    The Dutch government is compelled to measure radioactivity in the environment under terms of the Euratom Treaty of 1957. This report presents the results of radioactivity measurements in the Dutch environment in 2002. The measurements were carried out by RIVM, RIZA, RIKZ and Inspectorate for Health

  8. The challenge of monitoring the cryosphere in alpine environments: Prepare the present for the future

    Science.gov (United States)

    Fischer, Andrea; Helfricht, Kay; Seiser, Bernd; Stocker-Waldhuber, Martin; Hartl, Lea; Wiesenegger, Hans

    2017-04-01

    Understanding the interaction of mountain glaciers and permafrost with weather and climate is essential for the interpretation of past states of the cryosphere in terms of climate change. Most of the glaciers and rock glaciers in Eastern Alpine terrain are subject to strong gradients in climatic forcing, and the persistence of these gradients under past climatic conditions is, more or less, unknown. Thus a key challenge of monitoring the cryosphere is to define the demands on a monitoring strategy for capturing essential processes and their potential changes. For example, the effects of orographic precipitation and local shading vary with general circulation patterns and the amount of solar radiation during the melt(ing) season. Recent investigations based on the Austrian glacier inventories have shown that glacier distribution is closely linked to topography and climatic situation, and that these two parameters imply also different sensitivities of the specific glaciers to progressing climate change. This leads to the need to develop a monitoring system capturing past, but also fairly unknown future ensembles of climatic state and sensitivities. As a first step, the Austrian glacier monitoring network has been analyzed from the beginning of the records onwards. Today's monitoring network bears the imprints of past research interests, but also past funding policies and personal/institutional engagements. As a limitation for long term monitoring in general, today's monitoring strategies have to cope with being restricted to these historical commitments to preserve the length of the time series, but at the same time expanding the measurements to fulfil present and future scientific and societal demands. The decision on cryospheric benchmark sites has an additional uncertainty: the ongoing disintegration of glaciers, their increasing debris cover as well as the potential low ice content and relatively unknown reaction of rock glaciers in the course of climate change

  9. SoundProof: A Smartphone Platform for Wireless Monitoring of Wildlife and Environment

    Science.gov (United States)

    Lukac, M.; Monibi, M.; Lane, M. L.; Howell, L.; Ramanathan, N.; Borker, A.; McKown, M.; Croll, D.; Terschy, B.

    2011-12-01

    We are developing an open-source, low-cost wildlife and environmental monitoring solution based on Android smartphones. Using a smartphone instead of a traditional microcontroller or single board computer has several advantages: smartphones are single integrated devices with multiple radios and a battery; they have a robust software interface which enables customization; and are field-tested by millions of users daily. Consequently, smartphones can improve the cost, configurability, and real-time access to data for environmental monitoring, ultimately replacing existing monitoring solutions which are proprietary, difficult to customize, expensive, and require labor-intensive maintenance. While smartphones can radically change environmental and wildlife monitoring, there are a number of technical challenges to address. We present our smartphone-based platform, SoundProof, discuss the challenges of building an autonomous system based on Android phones, and our ongoing efforts to enable environmental monitoring. Our system is built using robust off-the-shelf hardware and mature open-source software where available, to increase scalability and ease of installation. Key features include: * High-quality acoustic signal collection from external microphones to monitor wildlife populations. * Real-time data access, remote programming, and configuration of the field sensor via wireless cellular or WiFi channels, accessible from a website. * Waterproof packaging and solar charger setup for long-term field deployments. * Rich instrumentation of the end-to-end system to quickly identify and debug problems. * Supplementary mesh networking system with long-range wireless antennae to provide coverage when no cell network is available. We have deployed this system to monitor Rufous Crowned Sparrows on Anacapa Island, Chinese Crested Turns on the Matsu Islands in Taiwan, and Ashy Storm Petrels on South East Farallon Island. We have testbeds at two UC Natural Reserves to field

  10. Development of a Compact Range-gated Vision System to Monitor Structures in Low-visibility Environments

    International Nuclear Information System (INIS)

    Ahn, Yong-Jin; Park, Seung-Kyu; Baik, Sung-Hoon; Kim, Dong-Lyul; Choi, Young-Soo; Jeong, Kyung-Min

    2015-01-01

    Image acquisition in disaster area or radiation area of nuclear industry is an important function for safety inspection and preparing appropriate damage control plans. So, automatic vision system to monitor structures and facilities in blurred smoking environments such as the places of a fire and detonation is essential. Vision systems can't acquire an image when the illumination light is blocked by disturbance materials, such as smoke, fog and dust. To overcome the imaging distortion caused by obstacle materials, robust vision systems should have extra-functions, such as active illumination through disturbance materials. One of active vision system is a range-gated imaging system. The vision system based on the range-gated imaging system can acquire image data from the blurred and darken light environments. Range-gated imaging (RGI) is a direct active visualization technique using a highly sensitive image sensor and a high intensity illuminant. Currently, the range-gated imaging technique providing 2D and range image data is one of emerging active vision technologies. The range-gated imaging system gets vision information by summing time sliced vision images. In the RGI system, a high intensity illuminant illuminates for ultra-short time and a highly sensitive image sensor is gated by ultra-short exposure time to only get the illumination light. Here, the illuminant illuminates objects by flashing strong light through disturbance materials, such as smoke particles and dust particles. In contrast to passive conventional vision systems, the RGI active vision technology enables operation even in harsh environments like low-visibility smoky environment. In this paper, a compact range-gated vision system is developed to monitor structures in low-visibility environment. The system consists of illumination light, a range-gating camera and a control computer. Visualization experiments are carried out in low-visibility foggy environment to see imaging capability

  11. Development of a Compact Range-gated Vision System to Monitor Structures in Low-visibility Environments

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Yong-Jin; Park, Seung-Kyu; Baik, Sung-Hoon; Kim, Dong-Lyul; Choi, Young-Soo; Jeong, Kyung-Min [KAERI, Daejeon (Korea, Republic of)

    2015-05-15

    Image acquisition in disaster area or radiation area of nuclear industry is an important function for safety inspection and preparing appropriate damage control plans. So, automatic vision system to monitor structures and facilities in blurred smoking environments such as the places of a fire and detonation is essential. Vision systems can't acquire an image when the illumination light is blocked by disturbance materials, such as smoke, fog and dust. To overcome the imaging distortion caused by obstacle materials, robust vision systems should have extra-functions, such as active illumination through disturbance materials. One of active vision system is a range-gated imaging system. The vision system based on the range-gated imaging system can acquire image data from the blurred and darken light environments. Range-gated imaging (RGI) is a direct active visualization technique using a highly sensitive image sensor and a high intensity illuminant. Currently, the range-gated imaging technique providing 2D and range image data is one of emerging active vision technologies. The range-gated imaging system gets vision information by summing time sliced vision images. In the RGI system, a high intensity illuminant illuminates for ultra-short time and a highly sensitive image sensor is gated by ultra-short exposure time to only get the illumination light. Here, the illuminant illuminates objects by flashing strong light through disturbance materials, such as smoke particles and dust particles. In contrast to passive conventional vision systems, the RGI active vision technology enables operation even in harsh environments like low-visibility smoky environment. In this paper, a compact range-gated vision system is developed to monitor structures in low-visibility environment. The system consists of illumination light, a range-gating camera and a control computer. Visualization experiments are carried out in low-visibility foggy environment to see imaging capability.

  12. Annual report on radioactive discharges from Winfrith and monitoring the environment 1989

    International Nuclear Information System (INIS)

    1990-03-01

    The numerical values of the authorised limits are based on past performance, future requirements and the application of BPM. As a 'back-stop', discharges at the limits must not result in doses to the most potentially exposed part of the local population -the critical group - exceeding 0.5 mSv per year. The limit of the International Commission on Radiological Protection (ICRP) for dose to a member of the general public is 1.0 mSv per year. During 1989 some small changes took place in our discharge patterns, our environmental monitoring and in the assessment of critical group doses. These changes are discussed in the introductions to the two parts of this report where the relevant Authorisations are also discussed. This report, the fifth of our annual series, has as its aim the provision, to the general public, of full information on discharges from the SGHWR reactor and other smaller sources at Winfrith and the associated environmental monitoring programmes. Some improvements in presentation have been made. The data, mainly provided graphically in the main text, are still compared with authorised limits or derived levels, but numerical values are now given. The graphs refer to specifically authorised radio-nuclides e.g. tritium, rather than to gross activity. Previous reports were restricted to monitoring at the site boundary and to off-site monitoring. Some data are now given in the report for on-site monitoring. (author)

  13. Possibility of continuous monitoring of environment around the nuclear plant using satellite remote sensing

    International Nuclear Information System (INIS)

    Sasaki, Takanori; Tanabu, Yoshimine; Fujita, Shigetaka; Zhao Wenhui

    2008-01-01

    Interest in nuclear power generation is increasing by rising of power demand and environmental concern. It is important more and more to confirm and show the safety operation of nuclear plants, which is useful to remove anxiety of residents. Satellite remote sensing is one of the way of it. Large observation width and long and continuous observation period are advantage of satellite remote sensing. In addition, it is very important to be able to monitor without visitation on the site. We have continued local area environmental analysis using various satellites. MODIS on Terra and Aqua which are NASA satellites received by Hachinohe Institute of Technology is mainly used. According to these results, we have shown that combined analysis of various information parameters such as land surface temperature, geographical changes, vegetation, etc. is very effective to monitor environmental changes. In these analyses, error detection is very important. Therefore, enough storage data with continuously monitoring in usual state is necessary. Moreover, it is thought that the confirmation of stable operation of plants by means of continuous monitoring can contribute to reduce residents' anxiety of nuclear power plant. Additionally, in the case that the change of influence on surroundings is detected, it is possible to grasp the situation and take measure in early stage by error detection. In this paper, as an possible example of continuous monitoring using satellite remote sensing, we introduce the result of analysis and investigation of which changes of sea surface temperature and chlorophyll concentration on the sea around power plant. (author)

  14. Monitoring equipment environment during nuclear plant operation at Salem and Hope Creek generating stations

    International Nuclear Information System (INIS)

    Blum, A.; Smith, R.J.

    1991-01-01

    Monitoring of environmental parameters has become a significant issue for operating nuclear power plants. While the long-term benefits of plant life extension programs are being pursued with comprehensive environmental monitoring programs, the potential effect of local hot spots at various plant locations needs to be evaluated for its effect on equipment degradation and shortening of equipment qualified life. A significant benefit can be experienced from temperature monitoring when a margin exists between the design versus actual operating temperature. This margin can be translated into longer equipment qualified life and significant reduction in maintenance activities. At PSE and G, the immediate need for monitoring environmental parameters is being accomplished via the use of a Logic Beach Bitlogger. The Bitlogger is a portable data loggings system consisting of a system base, input modules and a communication software package. Thermocouples are installed on selected electrical equipment and cables are run from the thermocouples to the input module of the Bitlogger. Temperature readings are taken at selected intervals, stored in memory, and downloaded periodically to a PC software program, i.e., Lotus. The data is formatted into tabular or graphical documents. Because of their versatility, Bitloggers are being used differently at the authors Nuclear facility. At the Salem Station (2 Units-4 loop Westinghouse PWR), a battery powered, fully portable, calibrated Bitlogger is located in an accessible area inside Containment where it monitors the temperature of various electrical equipment within the Pressurizer Enclosure. It is planned that close monitoring of the local hot spot temperatures in this area will allow them to adjust and reconcile the environmental qualification of the equipment

  15. GÉANT PERFsonar MDM-Based Circuit Monitoring in a Multidomain Environment

    DEFF Research Database (Denmark)

    Kleist, Josva; Yu, Hao; Dittmann, Lars

    2014-01-01

    Global research collaborations today require reliable and secure dedicated network connections to facilitate data communications between collaborating partners. To deal with the deluge of data, dedicated connections are needed to transport data in a highly efficient manner. Managing such links......, which often cross multiple administrative domains with heterogeneous infrastructure, poses many compelling research challenges, one of which is interdomain network monitoring. In this article, a multidomain circuit monitoring system, CMon, is introduced. Using some services of GÉANT perfSONAR MDM, CMon...

  16. Environment radiological monitoring by JNC related to the JCO criticality accident

    International Nuclear Information System (INIS)

    Watanabe, Hitoshi

    2001-01-01

    Concerning the criticality accident at JCO Co., Ltd. (JCO) which occurred at 10:35 on 30th Sep. 1999, Japan Nuclear Cycle Development Institute (JNC) established ''JNC's task force'' at 12:35 on the same data in conjunction with Head Office and Tokai Works. JNC's task force had collaborated on environmental radiological monitoring with the government of Japan and the local governments. This report compiles the results of the environmental monitoring performed by JNC's task force based on the request from the government of Japan and the local governments. (author)

  17. Annual report on radioactive discharges and monitoring of the environment 1981

    International Nuclear Information System (INIS)

    1982-07-01

    A report is given on discharges and disposal of radioactive wastes through authorised outlets and on environmental monitoring for all of BNFL's Company Works and Sites during 1981. At no time during 1981 have discharges and disposals of radioactive wastes at any of the Works or Sites exceeded those laid down in any of the Authorisations. Similarly, environmental monitoring studies have shown that the radiation doses to the most highly exposed group of the general population were significantly lower than the dose limit recommended by the ICRP. (U.K.)

  18. Quantum Fingerprint-Based Air Quality Monitoring in Coastal Environments, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Coastal environments vital to our nation are strongly impacted by natural and human factors and are also sensitive to global climate change. A need exists for...

  19. Development of monitoring-control methods for heavy remote handling operations in an irradiated environment

    Energy Technology Data Exchange (ETDEWEB)

    Argouac' h, J R [Alsthom-Atlantique, ACB Nantes (France)

    1984-11-01

    Heavy remote handling equipment units have benefited from the progress made in robotics, but with certain specific constraints linked to the environment in which they are required to operate. Notably, these constraints impose the exclusive use of electrical techniques.

  20. The radiation monitoring of environment around place of treatment and storage of radioactive wastes

    International Nuclear Information System (INIS)

    Vdovina, E.D.

    2001-01-01

    Full text: Large success was attained in the field of radiation protection of research nuclear center, but it is necessary to carry out works in this way around place of treatment and storage of radioactive wastes too. Moreover, for protection of environment it is necessary to control radiation condition of system (radioactive wastes of nuclear center - environment). There is large amount of natural and man-made radionuclides in environment and it is important to solve problem to control individual radionuclides, polluting natural environment. Also, it is necessary to control concentrations of specific radionuclides, which are marks of definite radioactive source. The radionuclides 137 Cs, 90 Sr, 60 Co, 141 Ce, 144 Ce, 95 Zr, 95 Nb, 131 I and natural radionuclides of uranium, thorium and their products of decay are basic radionuclides. The 57 Co, 35 S, 32 P are considered also basic radionuclides taking into consideration specialization of our Institute. The basic problems of control of environment are following: observation of radioactive pollution level of environment objects; estimation of radioactive pollution level with the purpose of warning of possible negative consequences; investigation of dynamics of radioactivity and prognosis of radioactive pollution of environment objects; influence on sources of radioactive pollution. There is large volume information, characterizing radiation condition of environment around research nuclear center and around place of treatment and storage of radioactive wastes. The bank of environment object analysis result date was build for investigation of information. The system of protection around location of treatment and storage of radioactive wastes and around nuclear center consists of control of radioactive wastes, superficial and underground water, soil, plants, atmospheric precipitation. There are analysis of total β- activity, α-activity and γ-spectrometry. This control includes estimation of throw down values

  1. A Decision Matrix and Monitoring based Framework for Infrastructure Performance Enhancement in A Cloud based Environment

    OpenAIRE

    Alam, Mansaf; Shakil, Kashish Ara

    2014-01-01

    Cloud environment is very different from traditional computing environment and therefore tracking the performance of cloud leverages additional requirements. The movement of data in cloud is very fast. Hence, it requires that resources and infrastructure available at disposal must be equally competent. Infrastructure level performance in cloud involves the performance of servers, network and storage which act as the heart and soul for driving the entire cloud business. Thus a constant improve...

  2. A monitor for the laboratory evaluation of control integrity in digital control systems operating in harsh electromagnetic environments

    Science.gov (United States)

    Belcastro, Celeste M.; Fischl, Robert; Kam, Moshe

    1992-01-01

    This paper presents a strategy for dynamically monitoring digital controllers in the laboratory for susceptibility to electromagnetic disturbances that compromise control integrity. The integrity of digital control systems operating in harsh electromagnetic environments can be compromised by upsets caused by induced transient electrical signals. Digital system upset is a functional error mode that involves no component damage, can occur simultaneously in all channels of a redundant control computer, and is software dependent. The motivation for this work is the need to develop tools and techniques that can be used in the laboratory to validate and/or certify critical aircraft controllers operating in electromagnetically adverse environments that result from lightning, high-intensity radiated fields (HIRF), and nuclear electromagnetic pulses (NEMP). The detection strategy presented in this paper provides dynamic monitoring of a given control computer for degraded functional integrity resulting from redundancy management errors, control calculation errors, and control correctness/effectiveness errors. In particular, this paper discusses the use of Kalman filtering, data fusion, and statistical decision theory in monitoring a given digital controller for control calculation errors.

  3. Monitoring the ecology and environment using remote sensing in the Jinta area/Middle Reaches of Heihe River Basin

    Science.gov (United States)

    Lu, Anxin; Wang, Lihong; Chen, Xianzhang

    2003-07-01

    A major monitoring area, a part of the middle reaches of Heihe basin, was selected. The Landsat TM data in summer of 1990 and 2000 were used with interpretation on the computer screen, classification and setting up environmental investigation database (1:100000) combined with DEM, land cover/land use, land type data and etc., according to the environmental classification system. Then towards to the main problems of environment, the spatial statistical analysis and dynamic comparisons were carried out using the database. The dynamic monitoring results of 1999 and 2000 show that the changing percentage with the area of 6 ground objects are as follows: land use and agriculture land use increased by 34.17% and 19.47% respectively, wet land and water-body also increased by 6.29% and 8.03% respectively; unused land increased by 1.73% and the biggest change is natural/semi-natural vegetation area, decreased by 42.78%, the main results above meat with the requirements of precise and practical conditions by the precise exam and spot check. With the combinations of using TM remote sensing data and rich un-remote sensing data, the investigations of ecology and environment and the dynamic monitoring would be carried out efficiently in the arid area. It is a dangerous signal of large area desertification if the area of natural/semi-natural vegetation is reduced continuously and obviously.

  4. Combining remote sensing and on-site monitoring methods to investigate footpath erosion within a popular recreational heathland environment.

    Science.gov (United States)

    Rodway-Dyer, Sue; Ellis, Nicola

    2018-06-01

    Footpaths are a prominent consequence of natural area tourism and reflect damage caused to valuable, sensitive habitats by people pressure. Degradation impacts on vegetation, wildlife, on and off-site soil movement and loss, creation of additional informal off-path footpaths (desire lines), and visual destruction of landscapes. Impacts need to be measured and monitored on a large temporal and spatial scale to aid in land management to maintain access and preserve natural environments. This study combined remote sensing (Light Detection and Ranging [LiDAR] and aerial photography) with on-site measurement of footpaths within a sensitive heathland habitat (Land's End, Cornwall, UK). Soil loss, slope angle change, vegetation damage and a hydrology model were combined to comprehensively study the site. Results showed 0.09 m mean soil loss over five years, footpath widening, increasing grass cover into heathland, and water channelling on the footpaths exacerbating erosion. The environments surrounding the footpaths were affected with visitors walking off path, requiring further management and monitoring. Multiple remote sensing techniques were highly successful in comprehensively assessing the area, particularly the hydrology model, demonstrating the potential of providing a valuable objective and quantitative monitoring and management tool. Copyright © 2018 Elsevier Ltd. All rights reserved.

  5. Modeling and Monitoring Terrestrial Primary Production in a Changing Global Environment: Toward a Multiscale Synthesis of Observation and Simulation

    Directory of Open Access Journals (Sweden)

    Shufen Pan

    2014-01-01

    Full Text Available There is a critical need to monitor and predict terrestrial primary production, the key indicator of ecosystem functioning, in a changing global environment. Here we provide a brief review of three major approaches to monitoring and predicting terrestrial primary production: (1 ground-based field measurements, (2 satellite-based observations, and (3 process-based ecosystem modelling. Much uncertainty exists in the multi-approach estimations of terrestrial gross primary production (GPP and net primary production (NPP. To improve the capacity of model simulation and prediction, it is essential to evaluate ecosystem models against ground and satellite-based measurements and observations. As a case, we have shown the performance of the dynamic land ecosystem model (DLEM at various scales from site to region to global. We also discuss how terrestrial primary production might respond to climate change and increasing atmospheric CO2 and uncertainties associated with model and data. Further progress in monitoring and predicting terrestrial primary production requires a multiscale synthesis of observations and model simulations. In the Anthropocene era in which human activity has indeed changed the Earth’s biosphere, therefore, it is essential to incorporate the socioeconomic component into terrestrial ecosystem models for accurately estimating and predicting terrestrial primary production in a changing global environment.

  6. Monitoring of Trichloroethene and Tetrachloroethene Content in Soil-Water Environment in Third Phase of Ecological Audit of Land

    Directory of Open Access Journals (Sweden)

    Pusz Agnieszka

    2014-07-01

    Full Text Available Trichloroethene (TCE and tetrachloroethene (PCE are chemical compounds which pose a serious threat for human health. Their specific properties make it possible that these substances may linger in soil and water for many years. These are the reasons why wells with water designed for drinking purposes have been subject of monitoring since 2006. This paper presents the results of monitoring research conducted in the soil-water environment within the framework in third phase of an ecological audit of land. The ecological audit of land made it possible to identify the cause and degree of the degradation, and helped formulate rationale for remedy decisions pertaining to the land (remediation/reclamation. The objective of the paper was to determine the pollution status of the soil-water environment and, subsequently, monitor (in years 2008-2010 the contents of the hazardous substances, namely trichloroethene and tetrachloroethene, within the area of the potential impact of metallurgical plant located in borders of the Main Underground Water Reservoir Wierzbica-Ostrowiec (GZWP 420 in in voivodeship Świętokrzyskie.

  7. Radioecological monitoring of the environment of a French nuclear power plant after 12 years in operation

    International Nuclear Information System (INIS)

    Foulquier, L.; Descamps, B.; Roussel, S.

    1992-01-01

    Taking Fessenheim Nuclear Power Plant as an example, this paper gives a description of various types of environmental test carried out under the responsibility of the Operator of Nuclear Power Plants in France: permanent monitoring of radioactivity, periodic radioecological assessments. The main results of measurements taken, show the effect of the Plant to be negligible. 8 refs., 1 fig., 4 tabs

  8. Satellite synthetic aperture radar for monitoring of surface deformation in shallow underground mining environments

    CSIR Research Space (South Africa)

    Engelbrecht, J

    2016-08-01

    Full Text Available . There are also human health-and-safety concerns in potentially unstable areas. To monitor the extent of deforming areas over time, ground-based surveys, including GPS and spirit-levelling techniques, are frequently employed. However, the process is time...

  9. Performance Evaluation of the United Nations Environment Programme Air Quality Monitoring Unit

    Science.gov (United States)

    A request for technical collaboration between the UNEP and the US EPA resulted in the establishment of a MCRADA. The purpose of this agreement was to evaluate an air quality monitoring system (referred to as the UNEP pod) developed by the UNEP for use in environmental situations ...

  10. Monitoring and Depth of Strategy Use in Computer-Based Learning Environments for Science and History

    Science.gov (United States)

    Deekens, Victor M.; Greene, Jeffrey A.; Lobczowski, Nikki G.

    2018-01-01

    Background: Self-regulated learning (SRL) models position metacognitive monitoring as central to SRL processing and predictive of student learning outcomes (Winne & Hadwin, 2008; Zimmerman, 2000). A body of research evidence also indicates that depth of strategy use, ranging from surface to deep processing, is predictive of learning…

  11. Monitoring human health behaviour in one's living environment: a technological review.

    Science.gov (United States)

    Lowe, Shane A; Ólaighin, Gearóid

    2014-02-01

    The electronic monitoring of human health behaviour using computer techniques has been an active research area for the past few decades. A wide array of different approaches have been investigated using various technologies including inertial sensors, Global Positioning System, smart homes, Radio Frequency IDentification and others. It is only in recent years that research has turned towards a sensor fusion approach using several different technologies in single systems or devices. These systems allow for an increased volume of data to be collected and for activity data to be better used as measures of behaviour. This change may be due to decreasing hardware costs, smaller sensors, increased power efficiency or increases in portability. This paper is intended to act as a reference for the design of multi-sensor behaviour monitoring systems. The range of technologies that have been used in isolation for behaviour monitoring both in research and commercial devices are reviewed and discussed. Filtering, range, sensitivity, usability and other considerations of different technologies are discussed. A brief overview of commercially available activity monitors and their technology is also included. Copyright © 2013 IPEM. Published by Elsevier Ltd. All rights reserved.

  12. A UAV based system for real time flash flood monitoring in desert environments using Lagrangian microsensors

    KAUST Repository

    Abdelkader, Mohamed; Shaqura, Mohammad; Claudel, Christian G.; Gueaieb, Wail

    2013-01-01

    with advance warning, for which real time monitoring is critical. While satellite-based high resolution weather forecasts can help predict floods to a certain extent, they are not reliable enough, as flood models depend on a large number of parameters

  13. Monitoring of biological odour filtration in closed environments with olfactometry and an electronic nose

    NARCIS (Netherlands)

    Willers, H.C.; Gijsel, de P.; Ogink, N.W.M.; Amico, D' A.; Martinelli, E.; Natale, Di C.; Ras, van N.; Waarde, van der J.

    2004-01-01

    Air treatment with a compact biological membrane filter, and air quality monitoring with an electronic nose were tested in the laboratory on air from a cage containing six mice. Additional analyses of air to and from the filter were performed using olfactometry and ammonia and hydrogen sulphide gas

  14. Nitrogen balances at farm level as a tool to monitor effects of agri-environment policy

    NARCIS (Netherlands)

    Brouwer, F.M.

    1998-01-01

    Nitrogen balances at farm level are an important tool for monitoring the effects of agri-environmental policy in the European Union. Nitrogen surpluses, defined as the difference between input and output flows, are a pressure indicator to link agricultural activities with environmental quality

  15. NRPA. Radioactivity in the marine environment 2008 and 2009. Results from the Norwegian national monitoring programme (RAME)

    International Nuclear Information System (INIS)

    Gaefvert, T.; Heldal, H. E.; Brungot, A. L.; Gwynn, J.; Svaeren, I.; Kolstad, A. K.; Moeller, B.; Straalberg, E.; Christensen, G. C.; Drefvelin, J.; Dowdall, M.; Lind, B.; Rudjord, A. L.

    2011-04-01

    The issue of present and potential radioactive contamination in the marine environment has received considerable attention in Norway. In the late 1980s several accidents and incidents involving nuclear-powered submarines,demonstrated that the risk of the release of radionuclides into the Barents Sea should be considered more carefully. In particular, it became evident that better documentation concerning the radioactivity levels in fish and other seafood was important for the seafood export industries. Furthermore, in the early 1990s, information concerning the dumping of nuclear waste emerged through bilateral environmental cooperation between Norway and Russia. In the years that followed, concern grew regarding the safety of military and civil nuclear installations in the northwest of Russia. This concern was associated not only with possible reactor accidents, but also with the prolonged or sudden release of radio-nuclides from radioactive waste facilities.In addition to the potential threats outlined above, radionuclides originating from nuclear weapons fallout, the Chernobyl accident and waste discharged from European reprocessing facilities have been detected in the Norwegian marine environment. In 1994 and 1995, the discharge of 99Tc from the reprocessing facility at Sellafield in the UK increased sharply, and although this discharge has been reduced, it continued at a high level up to 2003. There has been much public concern about the consequences of such kinds of release, as the radionuclides discharged to the Irish Sea are transported by ocean currents via the North Sea into the Norwegian coastal current and to the Barents Sea. In response to this concern, programmes for the monitoring of radioactivity in the marine environment have been established. Due to the economic importance of the fishing industry and its vulnerability to contamination, as well as any rumours of radioactive contamination, one of the main objectives of these programmes is to

  16. Development of system decision support tools for behavioral trends monitoring of machinery maintenance in a competitive environment

    Science.gov (United States)

    Adeyeri, Michael Kanisuru; Mpofu, Khumbulani

    2017-06-01

    The article is centred on software system development for manufacturing company that produces polyethylene bags using mostly conventional machines in a competitive world where each business enterprise desires to stand tall. This is meant to assist in gaining market shares, taking maintenance and production decisions by the dynamism and flexibilities embedded in the package as customers' demand varies under the duress of meeting the set goals. The production and machine condition monitoring software (PMCMS) is programmed in C# and designed in such a way to support hardware integration, real-time machine conditions monitoring, which is based on condition maintenance approach, maintenance decision suggestions and suitable production strategies as the demand for products keeps changing in a highly competitive environment. PMCMS works with an embedded device which feeds it with data from the various machines being monitored at the workstation, and the data are read at the base station through transmission via a wireless transceiver and stored in a database. A case study was used in the implementation of the developed system, and the results show that it can monitor the machine's health condition effectively by displaying machines' health status, gives repair suggestions to probable faults, decides strategy for both production methods and maintenance, and, thus, can enhance maintenance performance obviously.

  17. Natural disaster reduction applications of the Chinese small satellite constellation for environment and disaster monitoring and forecasting

    Science.gov (United States)

    Liu, Sanchao; Fan, Yida; Gao, Maofang

    2013-10-01

    The Small Satellite Constellation for Environment and Disaster Monitoring and Forecasting (SSCEDMF) is an important component of Chinese satellites earth observation system. The first stage of SSCEDMF is composed by "2+1" satellites. The 2 optical satellites (HJ-1-A and HJ-1-B) and 1 S band microwave satellite (HJ-1-C) were successful launched on September 6, 2008 and November 19, 2012 respectively. This article introduced SSCEDMF characteristic and the disaster reduction application system and satellites on-orbit test works, and also analyzed the application capacity in natural disasters included flood, ice flooding, wild fire, severely drought, snow disasters, large area landslide and debris flow, sea ice, earthquake recovering, desertification and plant diseases and insect pests. Furthermore, we show some cases of China's and other countries' new natural disasters forecasting, monitoring, assessment and recovery construction.

  18. Proceedings (slides) of the ANCCLI-IRSN seminar: 'environment - health: what monitoring in territories by the different actors'

    International Nuclear Information System (INIS)

    2012-01-01

    Relations between the operation of nuclear facilities and the health of populations are recurrent topics. For this reason, the national association of information committees and local commissions (ANCCLI), and the radiation protection and nuclear safety institute (IRSN) have jointly organized this seminar devoted to the monitoring of environment and public health. Its aim was to share the experience of the different actors in order to help the local commissions of information (CLI) in carrying out their own actions on these topics. The first day, the Golfech, Gravelines, Cadarache and Saint-Laurent-Des-Eaux CLIs presented their local environmental monitoring actions and their impact studies for facilities effluents. IRSN presented its methodology for the elaboration of its annual radiological status of the French environment. A round table permitted the different intervening parties to exchange about their monitoring goals. The second day, the Tricastin and Gravelines CLI, as well as the health care supervision institute InVS), presented different studies and attempts of answers to the health-impact questions coming from the surrounding communities. The contributions and limitations of public health studies were discussed through a presentation of the joint ANCCLI/IRSN/InVS methodological guidebook 'public health in the vicinity of nuclear facilities: how to approach the questions asked'. This document gathers the slides of the available presentations: 1 - Environmental monitoring by the Tarn-et-Garonne departmental laboratory in partnership with the Golfech's CLI (A. Calafat); 2 - Environmental monitoring by the Tarn-et-Garonne veterinary laboratory (V. Rossetto); 3 - Independent environmental monitoring by the Tarn-et-Garonne and occasional expertises around the Gravelines site (F. Cazier); 4 - Study of the impact on Durance river of the liquid radiological effluents of CEA-Cadarache site (C. Fourcaud); 5 - Study of the impact on Loire river of the chemical

  19. Cyber-physical security of Wide-Area Monitoring, Protection and Control in a smart grid environment.

    Science.gov (United States)

    Ashok, Aditya; Hahn, Adam; Govindarasu, Manimaran

    2014-07-01

    Smart grid initiatives will produce a grid that is increasingly dependent on its cyber infrastructure in order to support the numerous power applications necessary to provide improved grid monitoring and control capabilities. However, recent findings documented in government reports and other literature, indicate the growing threat of cyber-based attacks in numbers and sophistication targeting the nation's electric grid and other critical infrastructures. Specifically, this paper discusses cyber-physical security of Wide-Area Monitoring, Protection and Control (WAMPAC) from a coordinated cyber attack perspective and introduces a game-theoretic approach to address the issue. Finally, the paper briefly describes how cyber-physical testbeds can be used to evaluate the security research and perform realistic attack-defense studies for smart grid type environments.

  20. Cyber-physical security of Wide-Area Monitoring, Protection and Control in a smart grid environment

    Science.gov (United States)

    Ashok, Aditya; Hahn, Adam; Govindarasu, Manimaran

    2013-01-01

    Smart grid initiatives will produce a grid that is increasingly dependent on its cyber infrastructure in order to support the numerous power applications necessary to provide improved grid monitoring and control capabilities. However, recent findings documented in government reports and other literature, indicate the growing threat of cyber-based attacks in numbers and sophistication targeting the nation’s electric grid and other critical infrastructures. Specifically, this paper discusses cyber-physical security of Wide-Area Monitoring, Protection and Control (WAMPAC) from a coordinated cyber attack perspective and introduces a game-theoretic approach to address the issue. Finally, the paper briefly describes how cyber-physical testbeds can be used to evaluate the security research and perform realistic attack-defense studies for smart grid type environments. PMID:25685516

  1. SEM probe of IC radiation sensitivity

    Science.gov (United States)

    Gauthier, M. K.; Stanley, A. G.

    1979-01-01

    Scanning Electron Microscope (SEM) used to irradiate single integrated circuit (IC) subcomponent to test for radiation sensitivity can localize area of IC less than .03 by .03 mm for determination of exact location of radiation sensitive section.

  2. Environmental radiation monitoring on the CERN sites and in the CERN environment during 1998

    Energy Technology Data Exchange (ETDEWEB)

    Vojtyla, P; Wittekind, D

    1999-04-15

    As a consequence of changes in the administrative structure of TIS Division in 1996 and 1997, the Environmental Section was integrated into the TIS Technical Services and Environment Group that also looks after the non-radiation parameters in the CERN releases and environment. However, it remains the duty of the Radiation Protection Group (RP) to define the environmental programme for radiation and radioactivity, and of the leader of RP to report its results both inside and outside CERN. Part I of this Annual Report describes the results of measurements which are relevant for assessing the radiological impact of CERN's activities on the environment and the population living in the vicinity of the CERN sites. Measurements of radioactivity released into the atmosphere and into water, as well as measurements of stray radiation at or near the CERN site boundaries, are reported.

  3. Air-Sense: indoor environment monitoring evaluation system based on ZigBee network

    Science.gov (United States)

    Huang, Yang; Hu, Liang; Yang, Disheng; Liu, Hengchang

    2017-08-01

    In the modern life, people spend most of their time indoors. However, indoor environmental quality problems have always been affecting people’s social activities. In general, indoor environmental quality is also related to our indoor activities. Since most of the organic irritants and volatile gases are colorless, odorless and too tiny to be seen, because we have been unconsciously overlooked indoor environment quality. Consequently, our body suffer a great health problem. In this work, we propose Air-Sense system which utilizes the platform of ZigBee Network to collect and detect the real-time indoor environment quality. What’s more, Air-Sense system can also provide data analysis, and visualizing the results of the indoor environment to the user.

  4. WebSpy: An Architecture for Monitoring Web Server Availability in a Multi-Platform Environment

    Directory of Open Access Journals (Sweden)

    Madhan Mohan Thirukonda

    2002-01-01

    Full Text Available For an electronic business (e-business, customer satisfaction can be the difference between long-term success and short-term failure. Customer satisfaction is highly impacted by Web server availability, as customers expect a Web site to be available twenty-four hours a day and seven days a week. Unfortunately, unscheduled Web server downtime is often beyond the control of the organization. What is needed is an effective means of identifying and recovering from Web server downtime in order to minimize the negative impact on the customer. An automated architecture, called WebSpy, has been developed to notify administration and to take immediate action when Web server downtime is detected. This paper describes the WebSpy architecture and differentiates it from other popular Web monitoring tools. The results of a case study are presented as a means of demonstrating WebSpy's effectiveness in monitoring Web server availability.

  5. On the relevance of efficient, integrated computer and network monitoring in HEP distributed online environment

    CERN Document Server

    Carvalho, D F; Delgado, V; Albert, J N; Bellas, N; Javello, J; Miere, Y; Ruffinoni, D; Smith, G

    1996-01-01

    Large Scientific Equipments are controlled by Computer System whose complexity is growing driven, on the one hand by the volume and variety of the information, its distributed nature, thhe sophistication of its trearment and, on the over hand by the fast evolution of the computer and network market. Some people call them generically Large-Scale Distributed Data Intensive Information Systems or Distributed Computer Control Systems (DCCS) for those systems dealing more with real time control. Taking advantage of (or forced by) the distributed architecture, the tasks are more and more often implemented as Client-Server applications. In this frame- work the monitoring of the computer nodes, the communications network and the applications becomes of primary importance for ensuring the safe running and guaranteed performance of the system. With the future generation of HEP experiments, such as those at the LHC in view, it is to integrate the various functions of DCCS monitoring into one general purpose Multi-layer ...

  6. On the Relevancy of Efficient, Integrated Computer and Network Monitoring in HEP Distributed Online Environment

    Science.gov (United States)

    Carvalho, D.; Gavillet, Ph.; Delgado, V.; Albert, J. N.; Bellas, N.; Javello, J.; Miere, Y.; Ruffinoni, D.; Smith, G.

    Large Scientific Equipments are controlled by Computer Systems whose complexity is growing driven, on the one hand by the volume and variety of the information, its distributed nature, the sophistication of its treatment and, on the other hand by the fast evolution of the computer and network market. Some people call them genetically Large-Scale Distributed Data Intensive Information Systems or Distributed Computer Control Systems (DCCS) for those systems dealing more with real time control. Taking advantage of (or forced by) the distributed architecture, the tasks are more and more often implemented as Client-Server applications. In this framework the monitoring of the computer nodes, the communications network and the applications becomes of primary importance for ensuring the safe running and guaranteed performance of the system. With the future generation of HEP experiments, such as those at the LHC in view, it is proposed to integrate the various functions of DCCS monitoring into one general purpose Multi-layer System.

  7. Real-time monitoring for alpha emitters in high-airflow environments

    International Nuclear Information System (INIS)

    Koster, J.E.; MacArthur, D.W.; Bounds, J.A.; Rawool-Sullivan, M.; Whitley, C.R.; Conaway, J.G.; Steadman, P.A.

    1996-01-01

    Key problems in detecting alpha contamination for site characterization and decontamination and decommissioning that remain to be solved include measurement of airborne contamination, material holdup within pipes, and leakage of material containers. These problems are very difficult using traditional alpha detectors and systems. The ionization detection method (long-range alpha detection of LRAD) offers a number of specific advantages for these environmental measurements. An LRAD system detects the air molecules ionized by alpha-emitting contamination rather than the alpha particles. Thus, LRAD-based detectors are not limited by the short range of alpha particles and can be used to detect contamination anywhere that air can penetrate. Extending this technology to large enclosures of long pipes requires a system optimized for large airflows. In this paper we will present designs and preliminary results for high-volume flow-through air monitors based on the LRAD technique. In addition, we will discuss the behavior of the monitors and their potential applications

  8. Method and apparatus for conducting structural health monitoring in a cryogenic, high vibration environment

    Science.gov (United States)

    Qing, Xinlin (Inventor); Beard, Shawn J. (Inventor); Li, Irene (Inventor)

    2013-01-01

    Sensors affixed to various such structures, where the sensors can withstand, remain affixed, and operate while undergoing both cryogenic temperatures and high vibrations. In particular, piezoelectric single crystal transducers are utilized, and these sensors are coupled to the structure via a low temperature, heat cured epoxy. This allows the transducers to monitor the structure while the engine is operating, even despite the harsh operating conditions. Aspects of the invention thus allow for real time monitoring and analysis of structures that operate in conditions that previously did not permit such analysis. A further aspect of the invention relates to use of piezoelectric single crystal transducers. In particular, use of such transducers allows the same elements to be used as both sensors and actuators.

  9. A UAV based system for real time flash flood monitoring in desert environments using Lagrangian microsensors

    KAUST Repository

    Abdelkader, Mohamed

    2013-05-01

    Floods are the most common natural disasters, causing thousands of casualties every year in the world. In particular, flash flood events are particularly deadly because of the short timescales on which they occur. Most casualties could be avoided with advance warning, for which real time monitoring is critical. While satellite-based high resolution weather forecasts can help predict floods to a certain extent, they are not reliable enough, as flood models depend on a large number of parameters that cannot be estimated beforehand. In this article, we present a novel flood sensing architecture to monitor large scale desert hydrological basins surrounding metropolitan areas, based on unmanned air vehicles. The system relies on Lagrangian (mobile) microsensors, that are released by a swarm of UAVs. A preliminary testbed implementing this technology is briefly described, and future research directions and problems are discussed. © 2013 IEEE.

  10. Automatic laser beam alignment using blob detection for an environment monitoring spectroscopy

    Science.gov (United States)

    Khidir, Jarjees; Chen, Youhua; Anderson, Gary

    2013-05-01

    This paper describes a fully automated system to align an infra-red laser beam with a small retro-reflector over a wide range of distances. The component development and test were especially used for an open-path spectrometer gas detection system. Using blob detection under OpenCV library, an automatic alignment algorithm was designed to achieve fast and accurate target detection in a complex background environment. Test results are presented to show that the proposed algorithm has been successfully applied to various target distances and environment conditions.

  11. Space Weather Monitoring for ISS Space Environments Engineering and Crew Auroral Observations

    Science.gov (United States)

    Minow, Joseph I.; Pettit, Donald R.; Hartman, William A.

    2012-01-01

    The awareness of potentially significant impacts of space weather on spaceand ground ]based technological systems has generated a strong desire in many sectors of government and industry to effectively transform knowledge and understanding of the variable space environment into useful tools and applications for use by those entities responsible for systems that may be vulnerable to space weather impacts. Essentially, effectively transitioning science knowledge to useful applications relevant to space weather has become important. This talk will present proven methodologies that have been demonstrated to be effective, and how in the current environment those can be applied to space weather transition efforts.

  12. 2. All-Polish Seminar: Monitoring of Radioactive Environment Contamination Using ASS-500 and PMS Stations

    International Nuclear Information System (INIS)

    1998-01-01

    During last 10 years the modern system of radiological pollution monitoring has been developed in Poland. At the beginning it was composed of ASS-500 stations. At the end of 1995 five automatic PMS stations have been installed as the result of the collaboration between Polish and Danish governments. Several stations of both types were include later. The system is coordinated by Central Laboratory for Radiological Protection. The report reviews the meeting dedicated to problems and future developments of the system

  13. Annual report on radioactive discharges and monitoring of the environment 1984

    International Nuclear Information System (INIS)

    1985-01-01

    Information is given on the liquid, airborne, and solid radioactive discharges through authorised outlets, and on environmental monitoring for all of BNFL's works and sites for 1984; ie Sellafield site and Drigg storage and disposal site; Chapelcross works; Springfields works and Ulnes Walton disposal site; Capenhurst works. Included is assessment of radiation doses to representative members of the most highly exposed group of the general population for the most important environmental pathways. (author)

  14. Significance of Operating Environment in Condition Monitoring of Large Civil Structures

    OpenAIRE

    Alampalli, Sreenivas

    1999-01-01

    Success of remote long-term condition monitoring of large civil structures and developing calibrated analytical models for damage detection, depend significantly on establishing accurate baseline signatures and their sensitivity. Most studies reported in the literature concentrated on the effect of structural damage on modal parameters without emphasis on reliability of modal parameters. Thus, a field bridge structure was studied for the significance of operating conditions in relation to bas...

  15. Integrity monitoring of vehicle positioning in urban environment using RTK-GNSS, IMU and speedometer

    Science.gov (United States)

    El-Mowafy, Ahmed; Kubo, Nobuaki

    2017-05-01

    Continuous and trustworthy positioning is a critical capability for advanced driver assistance systems (ADAS). To achieve continuous positioning, methods such as global navigation satellite systems real-time kinematic (RTK), Doppler-based positioning, and positioning using low-cost inertial measurement unit (IMU) with car speedometer data are combined in this study. To ensure reliable positioning, the system should have integrity monitoring above a certain level, such as 99%. Achieving this level when combining different types of measurements that have different characteristics and different types of errors is a challenge. In this study, a novel integrity monitoring approach is presented for the proposed integrated system. A threat model of the measurements of the system components is discussed, which includes both the nominal performance and possible fault modes. A new protection level is presented to bound the maximum directional position error. The proposed approach was evaluated through a kinematic test in an urban area in Japan with a focus on horizontal positioning. Test results show that by integrating RTK, Doppler with IMU/speedometer, 100% positioning availability was achieved. The integrity monitoring availability was assessed and found to meet the target value where the position errors were bounded by the protection level, which was also less than an alert level, indicating the effectiveness of the proposed approach.

  16. Monitoring Litter Inputs from the Adour River (Southwest France to the Marine Environment

    Directory of Open Access Journals (Sweden)

    Antoine Bruge

    2018-03-01

    Full Text Available Rivers are major pathways for litter to enter the ocean, especially plastic debris. Yet, further research is needed to improve knowledge on rivers contribution, increase data availability, refine litter origins, and develop relevant solutions to limit riverine litter inputs. This study presents the results of three years of aquatic litter monitoring on the Adour river catchment (southwest of France. Litter monitoring consisted of collecting all litter stranded on river banks or stuck in the riparian vegetation in defined areas identified from cartographic and hydromorphological analyses, and with the support of local stakeholders. Litter samples were then sorted and counted according to a list of items containing 130 categories. Since 2014, 278 litter samplings were carried out, and 120,632 litter items were collected, sorted, and counted. 41% of litter could not be identified due to high degradation. Food and beverage packaging, smoking-related items, sewage related debris, fishery and mariculture gear, and common household items represented around 70% of identifiable items. Overall, the present study contributes to our knowledge of litter sources and pathways, with the target of reducing the amounts entering the ocean. The long-term application of this monitoring is a way forward to measure societal changes as well as assess effectiveness of measures.

  17. Changing tides: Adaptive monitoring, assessment, and management of pharmaceutical hazards in the environment through time.

    Science.gov (United States)

    Gaw, Sally; Brooks, Bryan W

    2016-04-01

    Pharmaceuticals are ubiquitous contaminants in aquatic ecosystems. Adaptive monitoring, assessment, and management programs will be required to reduce the environmental hazards of pharmaceuticals of concern. Potentially underappreciated factors that drive the environmental dose of pharmaceuticals include regulatory approvals, marketing campaigns, pharmaceutical subsidies and reimbursement schemes, and societal acceptance. Sales data for 5 common antidepressants (duloxetine [Cymbalta], escitalopram [Lexapro], venlafaxine [Effexor], bupropion [Wellbutrin], and sertraline [Zoloft]) in the United States from 2004 to 2008 were modeled to explore how environmental hazards in aquatic ecosystems changed after patents were obtained or expired. Therapeutic hazard ratios for Effexor and Lexapro did not exceed 1; however, the therapeutic hazard ratio for Zoloft declined whereas the therapeutic hazard ratio for Cymbalta increased as a function of patent protection and sale patterns. These changes in therapeutic hazard ratios highlight the importance of considering current and future drivers of pharmaceutical use when prioritizing pharmaceuticals for water quality monitoring programs. When urban systems receiving discharges of environmental contaminants are examined, water quality efforts should identify, prioritize, and select target analytes presently in commerce for effluent monitoring and surveillance. © 2015 SETAC.

  18. Integrity monitoring of vehicle positioning in urban environment using RTK-GNSS, IMU and speedometer

    International Nuclear Information System (INIS)

    El-Mowafy, Ahmed; Kubo, Nobuaki

    2017-01-01

    Continuous and trustworthy positioning is a critical capability for advanced driver assistance systems (ADAS). To achieve continuous positioning, methods such as global navigation satellite systems real-time kinematic (RTK), Doppler-based positioning, and positioning using low-cost inertial measurement unit (IMU) with car speedometer data are combined in this study. To ensure reliable positioning, the system should have integrity monitoring above a certain level, such as 99%. Achieving this level when combining different types of measurements that have different characteristics and different types of errors is a challenge. In this study, a novel integrity monitoring approach is presented for the proposed integrated system. A threat model of the measurements of the system components is discussed, which includes both the nominal performance and possible fault modes. A new protection level is presented to bound the maximum directional position error. The proposed approach was evaluated through a kinematic test in an urban area in Japan with a focus on horizontal positioning. Test results show that by integrating RTK, Doppler with IMU/speedometer, 100% positioning availability was achieved. The integrity monitoring availability was assessed and found to meet the target value where the position errors were bounded by the protection level, which was also less than an alert level, indicating the effectiveness of the proposed approach. (paper)

  19. Radioactivity monitoring of life environment in the Republic of Croatia, Report for 2004 - IMI-CRZ-81

    International Nuclear Information System (INIS)

    2005-01-01

    The radioactivity measurement programme in the environment of Republic of Croatia for 2004 is continuation of measurements that have started in 1959. Sampling, radiochemical analyses and measurements were carried out by the Radiation Protection Unit, Institute for Medical Research and Occupational Health, Zagreb. The scope of the monitoring of contamination in the environmental samples according to the European Commission recommendations of 8 June 2000, was to collect samples of air, fallout, soil, water, alimentary products and fodder. The purpose of these investigations is to collect as many data as possible for the assessment of radiation risk to man. (author)

  20. Chlorinated hydrocarbons in the marine environment. A report prepared by the Panel on Monitoring Persistent Pesticides in the Marine Environment of the Committee on Oceanography

    Science.gov (United States)

    ,; Goldberg, E.D.; Butler, P.; Meier, P.; Menzel, D.; Paulik, G.; Risebrough, R.; Stickel, L.F.

    1971-01-01

    made immediately to effect a drastic reduction of the escape of persistent toxicants into the environment, with the ultimate aim of achieving virtual cessation in the shortest possible time. ? Programs should be designed both to determine the rates of entry of each pollutant into the marine environment and to make base-line determinations of the distribution of the pollutants among the components of that environment, These should be followed by a program of monitoring long-term trends in order to record progress and to document possible disaster. ? The laws relating to the registration of chemical substances and the release of production figures by government should be examined and perhaps revised in light of evidence of environmental deterioration caused by some of these substances.

  1. Monitoring of radiation in the environment in the Netherlands. Results in 2000

    NARCIS (Netherlands)

    Knetsch GJ; LSO; RIZA; RIKZ; Keuringsdienst van Waren

    2002-01-01

    This report presents the results of radioactivity measurements in the environment in the Netherlands carried out by RIVM, RIZA, RIKZ and Inspectorate for Health Protection and Veterinary Public Health in 2000. Measurements of radioactivity have been carried out in airborne particulates, deposition,

  2. Monitoring of radiation in the environment in the Netherlands. Results in 2001

    NARCIS (Netherlands)

    Knetsch GJ; RIZA; RIKZ; LSO

    2003-01-01

    This report presents the results of radioactivity measurements in the Dutch environment in 2001. The measurements were carried out by RIVM, RIZA, RIKZ and Inspectorate for Health Protection and Veterinary Public Health. Radioactivity measurements were carried out on airborne particles, deposition,

  3. Environmental radiation monitoring on the CERN sites and in the CERN environment during 1997

    Energy Technology Data Exchange (ETDEWEB)

    Vojtyla, P; Wittekind, D

    1998-04-10

    As a consequence of changes in the administrative structure of TIS Division in 1996 and 1997, the Environmental Section was integrated into the TIS Technical Services and Environment Group that also looks after the non-radiation parameters in the CERN releases and environment. However, it remains the duty of the Radiation Protection Group to define the environmental programme for radiation and radioactivity, and to report its results both inside and outside CERN. In 1997, the environmental programme was slightly modified after discussions with the Sektion zur Ueberwachung der Radioaktivitaet (SUeR) in Fribourg. Gamma spectroscopy analyses of moss and water plants collected once per year in the rivers l'Allondon, Le Lion, Le Nant d'Avril and La Versoix were added. Moss and water plants were chosen as they are sensitive indicators of the presence of natural and man-made radioactivity in the environment. Part I of this Annual Report describes the results of measurements which are relevant for assessing the radiological impact of CERN's activities on the environment and the population living in the vicinity of the CERN sites. Measurements of radioactivity released into the atmosphere and into water, as well as measurements of stray radiation at or near the CERN site boundaries, are reported.

  4. Effect-directed analysis supporting monitoring of aquatic environments — An in-depth overview

    NARCIS (Netherlands)

    Brack, W.; Ait-Aissa, S.; Burgess, R.M.; Creusot, N.; Di Paolo, C.; Escher, B.I.; Hewitt, L.M.; Hilscherova, K.; Hollender, J.; Hollert, H.; Jonker, W.; Kool, J.; Lamoree, M.H.; Muschket, M.; Neumann, S.; Rostkowski, P.; Ruttkies, C.; Schollee, J.; Schymanski, E.L.; Schulze, T.; Seiler, T.; Tindall, A.J.; De Aragão Umbuzeiro, G.; Vrana, B.; Krauss, M.

    2016-01-01

    Aquatic environments are often contaminated with complex mixtures of chemicals that may pose a risk to ecosystems and human health. This contamination cannot be addressed with target analysis alone but tools are required to reduce this complexity and identify those chemicals that might cause adverse

  5. Biodiversity Monitoring Using NGS Approaches on Unusual Substrates (2013 DOE JGI Genomics of Energy and Environment 8th Annual User Meeting)

    Energy Technology Data Exchange (ETDEWEB)

    Gilbert, Tom

    2013-03-01

    Tom Gilbert of the Natural History Museum of Denmark on "Biodiversity monitoring using NGS approaches on unusual substrates" at the 8th Annual Genomics of Energy & Environment Meeting in Walnut Creek, Calif.

  6. Monitoring of radioactivity in the environment 201; Overvaking av radioaktivitet i omgivnadene 2011. Resultat fraa Straalevernet sine Radnett- og luftfilterstasjonar og fraa Sivilforsvaret si radacmaaleteneste

    Energy Technology Data Exchange (ETDEWEB)

    Moeller, B.; Dyve, J.E.; Tazmini, K.

    2013-03-01

    The Report summarizes the data from Norwegian Radiation Protection Authority and The Norwegian Civil Defence monitoring programs for radioactivity in the environment in 2011. A short description of the systems is also presented.(Author)

  7. Guidelines for environmental monitoring after acute oil spill in the marine environment; Retningslinjer for miljoeundersoekelser i marint miljoe etter akutt oljeforurensning

    Energy Technology Data Exchange (ETDEWEB)

    Joergensen, N.M.; Camus, L.-H.; Larsen, B.; Voegele, G.M.; Spikkerud, C.; Anker-Nilsen, T.; Dijk, J van; Lorentsen, S.-H.; Stabbetorp, O.; Bjoerge, A.; Boitsov, S.; Klungsoeyr, J.

    2012-07-01

    Contents of environmental damage assessments and monitoring of acute oil spills in the marine environment are outlined. The guideline provides general advice on timing, contents and scope of post spill surveys for documenting biological recovery and food safety.(Author)

  8. Study of different Chemcatcher configurations in the monitoring of nonylphenol ethoxylates and nonylphenol in aquatic environment.

    Science.gov (United States)

    Ahkola, Heidi; Herve, Sirpa; Knuutinen, Juha

    2014-01-01

    The main aim of the European Union Water Framework Directive (WFD) (2000/60/EC) is to protect rivers, lakes, coastal waters and groundwaters (EC 2000). The implementation of the WFD requires monitoring the concentration levels of several priority pollutants such as nonylphenol ethoxylates (NPEOs) and nonylphenol (NP) in the area of EU. The present practices for determining the concentration levels of various pollutants are, in many respects, insufficient, and there is an urgent need to develop more cost-effective sampling methods. A passive sampling tool named Chemcatcher was tested for monitoring NPEOs and NP in aqueous media. These environmentally harmful substances have been widely used in different household and industrial applications, and they affect aquatic ecosystems, for example, by acting as endocrine disrupting compounds. The suitability of different receiving phases which were sulfonated styrene-divinylbenzene reversed phase polymer (SDB-RPS), standard styrene-divinyl benzene polymer (SDB-XC) and C-18 (octadecyl) was assessed in laboratory and field trials. The effect of a diffusion membrane on the accumulation of studied compounds was also investigated. The SDB-XC and C-18 receiving phases collected the NPEOs and NP most effectively. The water flow affected the accumulation factor of the studied substances in the field trials, and the water concentrations calculated using sampling rates were tenfold lower than those measured with conventional spot sampling. The concentration of the analytes in spot samples taken from the sampling sites might be higher because in that case, the particle-bound fraction is also measured. The NPEOs readily attach to suspended matter, and therefore, the total concentration of such compounds in water is much higher. Also, the spot samples were not taken daily but once a week, while the passive samplers collected the compounds continuously for 2- or 4-week time periods. This may cause differences when comparing the results of

  9. Annual report on radioactive discharges and monitoring of the environment 1982

    International Nuclear Information System (INIS)

    1983-08-01

    A report is given on the liquid, airborne and solid radioactive discharges through authorised outlets and on environmental monitoring for all of BNFL's Works and sites for 1982, i.e. Sellafield Site and the Drigg Storage and Disposal Site; Chapelcross Works; Springfields Works and the Ulnes Walton Disposal Site; and Capenhurst Works. The report includes assessment of radiation doses to representative members of the most highly exposed group of the general population for the most important environmental pathways. At no time during 1982 have discharges and disposals of radioactive wastes through authorised outlets at any of the above Works exceeded those laid down in any of the Authorisations. (U.K.)

  10. Ecological and hydrological monitoring of the natural environment with help of cosmic rays

    International Nuclear Information System (INIS)

    Oskomov, V.V.

    2001-01-01

    It is noted that with help cosmic ray it is possible measuring the contaminating element concentration in the atmosphere, near surface water layer, and soil by characteristic radiation of elements generated by cosmic rays. With aim of determination of hydrological and glaciology characteristics of glaciers and snow cover of mountain districts the method for moisture store determination in the substance with help of natural ionizing radiation were used. With help of automate remote system including a set of detectors for muons, neutrons and gamma quanta, and others ones placed near researched medium the ecological and hydrological monitoring is worked out

  11. Results of monitoring of tritium behaviour and its concentration in the objects of Chernobylsk NPP environment

    International Nuclear Information System (INIS)

    Badyaev, V.V.; Egorov, Yu.A.; Korobejnikov, V.L.; Krasnozhen, G.N.; Stegachev, G.F.; Tolstykh, V.D.

    1985-01-01

    Results of systematic observations on tritium behaviur at the Chernobyl NPP in the system ''source of formation-environment'' are presented. Investigations were conducted in a stepwise manner. Investigations of the first step were performed in order to make an experimental basis of the tritium dynamic model. Tritium activity is determined in all NPP technological subsystems, in cooling reservoir and in the atmosphere. The dynamic model of tritium accumulation at NPP with LWGR-reactor and its exchange with environment is developed and studied at the second step. The third step of investigations includes studies of tritium behaviour in complex experiments along with the behaviour of other radionuclides present in NPP releases and effluents incidentally state of environmental objects is recorded. It is shown that tritium specific activity in atmosphere does not exceed the background values. Tritium activity in leaves of trees is equal to (5-7)x10 -11 Ci/kg of mass

  12. Monitoring of the land and geological environment condition in the Eupatorijska arroyo in Dnipropetrovsk

    Directory of Open Access Journals (Sweden)

    Bogachenko L.D.

    2015-09-01

    Full Text Available The article analyzes the condition of the land and the geological environment in the Eupatorijska arroyo, engineering-geological estimation of the territory of the arroyo is carried out, negative engineering-geological processes and phenomena are defined. It was found that due to the negative technogenic impact in conjunction with natural and climatic factors, the slopes under study can be considered as those under the risk of landslides and therefore are in need of engineering protection.

  13. Aerotechnogenic Monitoring of Urban Environment on Snow Cover Pollution (on the Example of Voronezh City

    Directory of Open Access Journals (Sweden)

    Prozhorina Tatyana Ivanovna

    2014-09-01

    Full Text Available Snow cover is characterized by high sorption ability and represents an informative object in the process of identifying the technogenic pollution of urban environment. The article contains the results of the research on the chemical composition of the snow which fell in Voronezh in the winter period of 2013–2014. The coefficients of chemical elements concentration were calculated to provide objective characteristics of snow cover pollution. The authors analyze the connection between the presence of pollutants in snow and the level of technogenic impact. The obtained ranges of anomaly coefficients among anions reflect the composition of technogenic emissions. The mineralization of snow water reliably characterizes the intensity of anthropogenic impact on the urban environment, and the value of mineralization snow samples ranges from 62,6 (background to 183,9 mg/l. Maximum values of mineralization (more than 150 mg/l are typical for samples taken in transport area. High values of salinity (more than 120 mg/l are observed in snow samples taken in the industrial area, which confirms the high “technogenic pressure” on the urban environment in zones of industrial and transport potential of the city. The investigated functional areas can be arranged in the following series by descending level of contamination: transport area > industrial zone > residential and recreational areas > background territory. The study of the chemical composition of snow cover in the various functional areas of Voronezh allows to conclude that the pH level, mineralization and the content of suspended solids in snow waters characterize the intensity of anthropogenic pressure on the urban environment, and the composition of melt waters indicates the nature of its pollution.

  14. Presence of thallium in the environment: sources of contaminations, distribution and monitoring methods.

    Science.gov (United States)

    Karbowska, Bozena

    2016-11-01

    Thallium is released into the biosphere from both natural and anthropogenic sources. It is generally present in the environment at low levels; however, human activity has greatly increased its content. Atmospheric emission and deposition from industrial sources have resulted in increased concentrations of thallium in the vicinity of mineral smelters and coal-burning facilities. Increased levels of thallium are found in vegetables, fruit and farm animals. Thallium is toxic even at very low concentrations and tends to accumulate in the environment once it enters the food chain. Thallium and thallium-based compounds exhibit higher water solubility compared to other heavy metals. They are therefore also more mobile (e.g. in soil), generally more bioavailable and tend to bioaccumulate in living organisms. The main aim of this review was to summarize the recent data regarding the actual level of thallium content in environmental niches and to elucidate the most significant sources of thallium in the environment. The review also includes an overview of analytical methods, which are commonly applied for determination of thallium in fly ash originating from industrial combustion of coal, in surface and underground waters, in soils and sediments (including soil derived from different parent materials), in plant and animal tissues as well as in human organisms.

  15. Development of Advanced In-Situ Techniques for Chemistry Monitoring and Corrosion Mitigation in SCWO Environments

    International Nuclear Information System (INIS)

    Macdonald, D. D.; Lvov, S. N.

    2000-01-01

    This project is developing sensing technologies and corrosion monitoring techniques for use in super critical water oxidation (SCWO) systems to reduce the volume of mixed low-level nuclear waste by oxidizing organic components in a closed cycle system where CO2 and other gaseous oxides are produced, leaving the radioactive elements concentrated in ash. The technique uses water at supercritical temperatures under highly oxidized conditions by maintaining a high fugacity of molecular oxygen in the system, which causes high corrosion rates of even the most corrosive resistant reactor materials. This project significantly addresses the high corrosion shortcoming through development of (a) advanced electrodes and sensors for in situ potentiometric monitoring of pH in high subcritical and supercritical aqueous solutions, (b) an approach for evaluating the association constants for 1-1 aqueous electrolytes using a flow-through electrochemical thermocell; (c) an electrochemical noise sensor for the in situ measurement of corrosion rate in subcritical and supercritical aqueous systems; (d) a model for estimating the effect of pressure on reaction rates, including corrosion reactions, in high subcritical and supercritical aqueous systems. The project achieved all objectives, except for installing some of the sensors into a fully operating SCWO system

  16. On the relevancy of efficient, integrated computer and network monitoring in HEP distributed online environment

    International Nuclear Information System (INIS)

    Carvalho, D.; Gavillet, Ph.; Delgado, V.; Javello, J.; Miere, Y.; Ruffinoni, D.; Albert, J.N.; Bellas, N.; Smith, G.

    1996-01-01

    Large Scientific Equipment are controlled by Computer Systems whose complexity is growing driven, on the one hand by the volume and variety of the information, its distributed nature, the sophistication of its treatment and, on the other hand by the fast evolution of the computer and network market. Some people call them generically Large-Scale Distributed Data Intensive Information Systems or Distributed Computer Control Systems (DCCS) for those systems dealing more with real time control. Taking advantage of (or forced by) the distributed architecture, the tasks are more and more often implemented as Client-Server applications. In this framework the monitoring of the computer nodes, the communications network and the applications becomes of primary importance for ensuring the the safe running and guaranteed performance of the system. With the future generation of HEP experiments, such as those at the LHC in view, it is proposed to integrate the various functions of DCCS monitoring into one general purpose Multi-layer System. (author)

  17. Distributed Smart Device for Monitoring, Control and Management of Electric Loads in Domotic Environments

    Directory of Open Access Journals (Sweden)

    Carlos Perez-Vidal

    2012-04-01

    Full Text Available This paper presents a microdevice for monitoring, control and management of electric loads at home. The key idea is to compact the electronic design as much as possible in order to install it inside a Schuko socket. Moreover, the electronic Schuko socket (electronic microdevice + Schuko socket has the feature of communicating with a central unit and with other microdevices over the existing powerlines. Using the existing power lines, the proposed device can be installed in new buildings or in old ones. The main use of this device is to monitor, control and manage electric loads to save energy and prevent accidents produced by different kind of devices (e.g., iron used in domestic tasks. The developed smart device is based on a single phase multifunction energy meter manufactured by Analog Devices (ADE7753 to measure the consumption of electrical energy and thento transmit it using a serial interface. To provide current measurement information to the ADE7753, an ultra flat SMD open loop integrated circuit current transducer based on the Hall effect principle manufactured by Lem (FHS-40P/SP600 has been used. Moreover, each smart device has a PL-3120 smart transceiver manufactured by LonWorks to execute the user’s program, to communicate with the ADE7753 via serial interface and to transmit information to the central unit via powerline communication. Experimental results show the exactitude of the measurements made using the developed smart device.

  18. Distributed smart device for monitoring, control and management of electric loads in domotic environments.

    Science.gov (United States)

    Morales, Ricardo; Badesa, Francisco J; García-Aracil, Nicolas; Perez-Vidal, Carlos; Sabater, Jose María

    2012-01-01

    This paper presents a microdevice for monitoring, control and management of electric loads at home. The key idea is to compact the electronic design as much as possible in order to install it inside a Schuko socket. Moreover, the electronic Schuko socket (electronic microdevice + Schuko socket) has the feature of communicating with a central unit and with other microdevices over the existing powerlines. Using the existing power lines, the proposed device can be installed in new buildings or in old ones. The main use of this device is to monitor, control and manage electric loads to save energy and prevent accidents produced by different kind of devices (e.g., iron) used in domestic tasks. The developed smart device is based on a single phase multifunction energy meter manufactured by Analog Devices (ADE7753) to measure the consumption of electrical energy and then to transmit it using a serial interface. To provide current measurement information to the ADE7753, an ultra flat SMD open loop integrated circuit current transducer based on the Hall effect principle manufactured by Lem (FHS-40P/SP600) has been used. Moreover, each smart device has a PL-3120 smart transceiver manufactured by LonWorks to execute the user's program, to communicate with the ADE7753 via serial interface and to transmit information to the central unit via powerline communication. Experimental results show the exactitude of the measurements made using the developed smart device.

  19. Annual report on radioactive discharges and monitoring of the environment 1980

    International Nuclear Information System (INIS)

    1981-07-01

    A report is given on radioactive discharges through authorised outlets and on environmental monitoring for all of British Nuclear Fuels Limited Works and Sites, i.e. the Windscale and Calder Works and the Drigg Storage and Disposal Site; Chapelcross Works; Springfields Works and the Ulnes Walton Disposal Site; and Capenhurst Works. The report includes information on liquid and airborne radioactive effluents and solid radioactive waste at each of the Company's Works and Sites. Assessments are made of maximum radiological exposures to individual members of the public expressed in terms of limits based on ICRP recommendations and in accordance with advice given by the NRPB. The report showed that at no time during 1980 did discharges and disposals of radioactive wastes through authorised outlets at any of the Works exceed those laid down in any of the Authorisations. Environmental monitoring studies also showed that the radiation exposure in 1980 of the most highly exposed groups of the general population was significantly lower than the Annual Limit recommended by the ICRP. (U.K.)

  20. Atmospheric environment measurement 3. Environmental pollution monitoring system using PIXE analysis

    International Nuclear Information System (INIS)

    Ishii, Keizo

    2009-01-01

    The PIXE(Proton Induced X-ray Emission) method is used in various fields owing to its high sensitivity. This method can be used to analyze multiple elements in a short time and therefore is suitable for the analysis of large quantities of environmental samples. We researched the effect of removing footwear in a room on indoor aerosol pollution. The concentration of aerosol particles in the case that footwear was not removed was 5 times larger than in the case when footwear was removed. We were able to identify a source of air pollution using both the results of PIXE analysis and information on wind direction. We applied PIXE analysis to investigate airborne yellow sand, which originals from the Gobi desert. By analyzing each yellow sand particle, hazardous yellow sand could be detected. We also applied PIXE analysis to river water pollution. River water samples were collected at a number of points along a river. The dilution of metallic elements by the river water was observed. Thus, it was shown that monitoring systems using the PIXE method are very useful for monitoring environmental pollution. (author)

  1. Development of Advanced In-Situ Techniques for Chemistry Monitoring and Corrosion Mitigation in SCWO Environments

    Energy Technology Data Exchange (ETDEWEB)

    Macdonald, D. D.; Lvov, S. N.

    2000-03-31

    This project is developing sensing technologies and corrosion monitoring techniques for use in super critical water oxidation (SCWO) systems to reduce the volume of mixed low-level nuclear waste by oxidizing organic components in a closed cycle system where CO2 and other gaseous oxides are produced, leaving the radioactive elements concentrated in ash. The technique uses water at supercritical temperatures under highly oxidized conditions by maintaining a high fugacity of molecular oxygen in the system, which causes high corrosion rates of even the most corrosive resistant reactor materials. This project significantly addresses the high corrosion shortcoming through development of (a) advanced electrodes and sensors for in situ potentiometric monitoring of pH in high subcritical and supercritical aqueous solutions, (b) an approach for evaluating the association constants for 1-1 aqueous electrolytes using a flow-through electrochemical thermocell; (c) an electrochemical noise sensor for the in situ measurement of corrosion rate in subcritical and supercritical aqueous systems; (d) a model for estimating the effect of pressure on reaction rates, including corrosion reactions, in high subcritical and supercritical aqueous systems. The project achieved all objectives, except for installing some of the sensors into a fully operating SCWO system.

  2. Escherichia Coli-Lux Biosensor Used to Monitor the Cytotoxicity and Genotoxicity of Pharmacological Residues in Environment

    Directory of Open Access Journals (Sweden)

    Eliza Hawrylik

    2018-05-01

    Full Text Available The aim of the study was to evaluate the usefulness of Escherichia coli K-12 RFM 443 recA::lux for cytotoxicity and genotoxicity monitoring of metoprolol in the environment. Metoprolol is one of the most popular cardiac drug which belongs to the group of β–blockers. The drug was applied at concentrations ranging from 0.01 µg/cm3 to 100 µg/cm3. The conducted studies are preliminary studies aimed at validation of the recA::lux gene construct in the direction of determining its sensitivity to metoprolol. The drug concentrations were selected experimentally to obtain a positive luminescence response. Obtained data indicated the influence of metoprolol on lux gene expression and recA promoter activity based on the use of laboratory samples using PBS buffer. Results indicate a potential possibility of using a bacterial biosensor Escherichia coli K - 12 RFM 443 with recA::lux gene fusion in cytotoxicity and genotoxicity monitoring of the cardiac drugs residue in the environment.

  3. Enhanced Sensitivity of Gas Sensor Based on Poly(3-hexylthiophene Thin-Film Transistors for Disease Diagnosis and Environment Monitoring

    Directory of Open Access Journals (Sweden)

    Marco R. Cavallari

    2015-04-01

    Full Text Available Electronic devices based on organic thin-film transistors (OTFT have the potential to supply the demand for portable and low-cost gadgets, mainly as sensors for in situ disease diagnosis and environment monitoring. For that reason, poly(3-hexylthiophene (P3HT as the active layer in the widely-used bottom-gate/bottom-contact OTFT structure was deposited over highly-doped silicon substrates covered with thermally-grown oxide to detect vapor-phase compounds. A ten-fold organochloride and ammonia sensitivity compared to bare sensors corroborated the application of this semiconducting polymer in sensors. Furthermore, P3HT TFTs presented approximately three-order higher normalized sensitivity than any chemical sensor addressed herein. The results demonstrate that while TFTs respond linearly at the lowest concentration values herein, chemical sensors present such an operating regime mostly above 2000 ppm. Simultaneous alteration of charge carrier mobility and threshold voltage is responsible for pushing the detection limit down to units of ppm of ammonia, as well as tens of ppm of alcohol or ketones. Nevertheless, P3HT transistors and chemical sensors could compose an electronic nose operated at room temperature for a wide range concentration evaluation (1–10,000 ppm of gaseous analytes. Targeted analytes include not only biomarkers for diseases, such as uremia, cirrhosis, lung cancer and diabetes, but also gases for environment monitoring in food, cosmetic and microelectronics industries.

  4. An Optical Fiber-Based Sensor Array for the Monitoring of Zinc and Copper Ions in Aqueous Environments

    Directory of Open Access Journals (Sweden)

    Steven Kopitzke

    2014-02-01

    Full Text Available Copper and zinc are elements commonly used in industrial applications as aqueous solutions. Before the solutions can be discharged into civil or native waterways, waste treatment processes must be undertaken to ensure compliance with government guidelines restricting the concentration of ions discharged in solution. While currently there are methods of analysis available to monitor these solutions, each method has disadvantages, be it high costs, inaccuracy, and/or being time-consuming. In this work, a new optical fiber-based platform capable of providing fast and accurate results when performing solution analysis for these metals is described. Fluorescent compounds that exhibit a high sensitivity and selectivity for either zinc or copper have been employed for fabricating the sensors. These sensors demonstrated sub-part-per-million detection limits, 30-second response times, and the ability to analyze samples with an average error of under 10%. The inclusion of a fluorescent compound as a reference material to compensate for fluctuations from pulsed excitation sources has further increased the reliability and accuracy of each sensor. Finally, after developing sensors capable of monitoring zinc and copper individually, these sensors are combined to form a single optical fiber sensor array capable of simultaneously monitoring concentration changes in zinc and copper in aqueous environments.

  5. Acoustic displacement sensor for harsh environment: application to SFR core support plate monitoring

    International Nuclear Information System (INIS)

    PeRISSE, J.; MACe, J.R.; VOUAGNER, P.

    2013-06-01

    The need for instrumentation able to monitor internal parameters inside reactor vessels during plant operation is getting stronger. Internal mechanical structures important for safety are concerned: for example core support plate, fuel assemblies or primary pumps. Because of very harsh environmental conditions (high temperature, pressure and radiation) and maintenance requirements, sensors are generally located on the outer shell of the vessel with, for example, strain gages, accelerometers, eddy current or US sensors. Then, some complex signal processing calculations must be performed to address internal structure behavior or health analysis but with bias effects (transfer path analysis method for example). This study will show an original displacement sensor based on an acoustic wave guide that can measure small displacement of mechanical structures inside reactor vessels. The application selected in this case is the monitoring of the core support plate for a sodium fast reactor (SFR). The wave guide - a thin tube sealed with pressurized argon gas inside - is installed inside the liquid sodium vessel (temperature between 400 deg. C to 550 deg. C). One extremity is connected to the mechanical structure for control. It includes two acoustic reflectors; such reflectors are dedicated to a calibration procedure to estimate the acoustic wave velocity whatever the temperature profile along the wave guide (velocity is temperature dependent). The opposite extremity of the wave guide is located outside the vessel and includes an emission/reception acoustic transducer. Using acoustic pulse reflectometry method, a plane wave pressure signal propagates inside the tube and reflects from the extremity and acoustic reflectors. The pulse-echo signals are recorded and processed in the frequency domain. Signal processing is performed to estimate the time of flight of pulse reflections patterns along the acoustic path. Then, monitored structure displacement - i.e. movement of the

  6. Study on Environment Performance Evaluation and Regional Differences of Strictly-Environmental-Monitored Cities in China

    Directory of Open Access Journals (Sweden)

    Ji Guo

    2017-12-01

    Full Text Available With the rapid economic growth and development, the problem of environmental pollution in China’s cities is becoming increasingly serious, and environmental pollution takes on a regional difference. There is, however, little comprehensive evaluation on the environmental performance and the regional difference of strictly-environmental-monitored cities in China. In this paper, the environmental performance of 109 strictly-environmental-monitored cities in China is evaluated in terms of natural performance, management performance, and scale performance by Data Envelopment Analysis (DEA, incorporating PM2.5 and PM10 as undesirable outputs. The empirical results show that: (1 At present, the natural performance is quite high, while the management performance is noticeably low for most cities. (2 The gap between the level of economic development and environmental protection among cities in China is large, and the scale efficiency of big cities is better than that of smaller cities. The efficiency value of large-scale cities such as Beijing, Shanghai, Guangzhou, Shenzhen, etc. is high, equaling 1; the value of smaller cities such as Sanmenxia, Baoding, Mudanjiang, and Pingdingshan is low, close to 0, indicating that big cities are characterized by high environmental efficiency. (3 From the perspective of region, the level of environmental performance in China is very uneven. For example, the environmental efficiency level of the Pan-Pearl River Delta region is superior to that of the Pan-Yangtze River region and the Bahia Rim region, whose values of environmental efficiency are 0.858, 0.658, and 0.622 respectively. The average efficiency of the Southern Coastal Economic Zone, Eastern Coastal Comprehensive Economic Zone, and the Comprehensive Economic Zone in the middle reaches of the Yangtze River is higher than that of other regions. Finally, corresponding countermeasures and suggestions are put forward. The method used in this paper is applicable

  7. Aeroflex Single Board Computers and Instrument Circuit Cards for Nuclear Environments Measuring and Monitoring

    International Nuclear Information System (INIS)

    Stratton, Sam; Stevenson, Dave; Magnifico, Mateo

    2013-06-01

    A Single Board Computer (SBC) is an entire computer including all of the required components and I/O interfaces built on a single circuit board. SBC's are used across numerous industrial, military and space flight applications. In the case of military and space implementations, SBC's employ advanced high reliability processors designed for rugged thermal, mechanical and even radiation environments. These processors, in turn, rely on equally advanced support components such as memory, interface, and digital logic. When all of these components are put together on a printed circuit card, the result is a highly reliable Single Board Computer that can perform a wide variety of tasks in very harsh environments. In the area of instrumentation, peripheral circuit cards can be developed that directly interface to the SBC and various radiation measuring devices and systems. Designers use signal conditioning and high reliability Analog to Digital Converters (ADC's) to convert the measuring device signals to digital data suitable for a microprocessor. The data can then be sent to the SBC via high speed communication protocols such as Ethernet or similar type of serial bus. Data received by the SBC can then be manipulated and processed into a form readily available to users. Recent events are causing some in the NPP industry to consider devices and systems with better radiation and temperature performance capability. Systems designed for space application are designed for the harsh environment of space which under certain conditions would be similar to what the electronics will see during a severe nuclear reactor event. The NPP industry should be considering higher reliability electronics for certain critical applications. (authors)

  8. Development of the computer code to monitor gamma radiation in the nuclear facility environment

    International Nuclear Information System (INIS)

    Akhmad, Y. R.; Pudjiyanto, M.S.

    1998-01-01

    Computer codes for gamma radiation monitoring in the vicinity of nuclear facility which have been developed could be introduced to the commercial potable gamma analyzer. The crucial stage of the first year activity was succeeded ; that is the codes have been tested to transfer data file (pulse high distribution) from Micro NOMAD gamma spectrometer (ORTEC product) and the convert them into dosimetry and physics quantities. Those computer codes are called as GABATAN (Gamma Analyzer of Batan) and NAGABAT (Natural Gamma Analyzer of Batan). GABATAN code can isable to used at various nuclear facilities for analyzing gamma field up to 9 MeV, while NAGABAT could be used for analyzing the contribution of natural gamma rays to the exposure rate in the certain location

  9. Space Based Measurements for Atmospheric Carbon Dioxide: a New Tool for Monitoring Our Environment

    Science.gov (United States)

    Crisp, David

    2015-01-01

    Fossil fuel combustion, deforestation, and other human activities are now adding almost 40 billion tons of carbon dioxide (CO2) to the atmosphere each year. Interestingly, as these emissions have increased over time, natural "sinks" in land biosphere and oceans have absorbed roughly half of this CO2, reducing the rate of atmospheric buildup by a half. Measurements of the increasing acidity (pH) of seawater indicate that the ocean absorbs one quarter of this CO2. Another quarter is apparently being absorbed by the land biosphere, but the identity and location of these natural land CO2 "sinks" are still unknown. The existing ground-based greenhouse gas monitoring network provides an accurate record of the atmospheric buildup, but still does not have the spatial resolution or coverage needed to identify or quantify CO2 sources and sinks.

  10. On the general principles of health monitoring of population living in NPP environment

    International Nuclear Information System (INIS)

    Dimitrov, P.

    1991-01-01

    The basic principles of health monitoring and its significance as a source of information for the organization and regulation of health control are pointed out. Attention is drawn to the surveillance and quantitative evaluation of the factors affecting individuals, as well as their consequencies. The necessity of determining the real health status of the population, as well as of forecasting its future changes and of evaluating the prognosticated changes is stressed. The nosologic units and classes of diseases, relevant to radiation action, should be put into constant observation. Special attention is paid to the study of demographic indices, congenital malformations, neoplasms of thyroid, lungs, leucoses, osteosarcomas, reproduction ability based on data for sterile marriages, spontaneous abortions, death-borns and perinatal lethality. 9 refs., 1 tab

  11. Evaluation of Content-Matched Range Monitoring Queries over Moving Objects in Mobile Computing Environments.

    Science.gov (United States)

    Jung, HaRim; Song, MoonBae; Youn, Hee Yong; Kim, Ung Mo

    2015-09-18

    A content-matched (CM) rangemonitoring query overmoving objects continually retrieves the moving objects (i) whose non-spatial attribute values are matched to given non-spatial query values; and (ii) that are currently located within a given spatial query range. In this paper, we propose a new query indexing structure, called the group-aware query region tree (GQR-tree) for efficient evaluation of CMrange monitoring queries. The primary role of the GQR-tree is to help the server leverage the computational capabilities of moving objects in order to improve the system performance in terms of the wireless communication cost and server workload. Through a series of comprehensive simulations, we verify the superiority of the GQR-tree method over the existing methods.

  12. Evaluation of Content-Matched Range Monitoring Queries over Moving Objects in Mobile Computing Environments

    Directory of Open Access Journals (Sweden)

    HaRim Jung

    2015-09-01

    Full Text Available A content-matched (CM rangemonitoring query overmoving objects continually retrieves the moving objects (i whose non-spatial attribute values are matched to given non-spatial query values; and (ii that are currently located within a given spatial query range. In this paper, we propose a new query indexing structure, called the group-aware query region tree (GQR-tree for efficient evaluation of CMrange monitoring queries. The primary role of the GQR-tree is to help the server leverage the computational capabilities of moving objects in order to improve the system performance in terms of the wireless communication cost and server workload. Through a series of comprehensive simulations, we verify the superiority of the GQR-tree method over the existing methods.

  13. Measurement comparisons of radioactivity among European monitoring laboratories for the environment and food stuff

    International Nuclear Information System (INIS)

    Waetjen, U.; Spasova, Y.; Altzitzoglou, T.

    2008-01-01

    For more than 15 years, European Union (EU) laboratories monitoring environmental radioactivity have been obliged to participate in measurement comparisons organised by the European Commission. After a short review of comparisons conducted during the 1990s, the approach of IRMM organising these comparisons since 2003 is presented. It relies on the provision of comparison samples with reference values traceable to the International Reference System for radionuclides (SIR). The results of the most recent comparison, the determination of 40 K, 90 Sr and 137 Cs in milk powder, are presented. The influence of repetitive participation in measurement comparisons on laboratory performance is studied on the basis of data from more than 20 laboratories having participated in several exercises during the last 15 years

  14. Induced Environment Contamination Monitor (IECM), air sampler - Results from the Space Transport System (STS-2) flight

    Science.gov (United States)

    Peters, P. N.; Hester, H. B.; Bertsch, W.; Mayfield, H.; Zatko, D.

    1983-01-01

    An investigation involving sampling the rapidly changing environment of the Shuttle cargo bay is considered. Four time-integrated samples and one rapid acquisition sample were collected to determine the types and quantities of contaminants present during ascent and descent of the Shuttle. The sampling times for the various bottles were controlled by valves operated by the Data Acquisition and Control System (DACS) of the IECM. Many of the observed species were found to be common solvents used in cleaning surfaces. When the actual volume sampled is taken into account, the relative mass of organics sampled during descent is about 20 percent less than during ascent.

  15. Open external circuit for microbial fuel cell sensor to monitor the nitrate in aquatic environment.

    Science.gov (United States)

    Wang, Donglin; Liang, Peng; Jiang, Yong; Liu, Panpan; Miao, Bo; Hao, Wen; Huang, Xia

    2018-07-15

    This study employed an open external circuit, rather than a closed circuit applied in previous studies, to operate an microbial fuel cell (MFC) sensor for real-time nitrate monitoring, and achieved surprisingly greater sensitivity (4.42 ± 0.3-6.66 ± 0.4 mV/(mg/L)) when the nitrate was at a concentration of 10-40 mg/L, compared to that of the MFC sensor with a closed circuit (0.8 ± 0.05-1.6 ± 0.1 mV/(mg/L)). The MFC sensor operated in open circuit (O-MFC sensor) delivered much more stable performance than that operated in closed circuit (C-MFC sensor) when affected by organic matter (NaAc). The sensitivity of O-MFC sensor was twice that of C-MFC sensor at a low background concentration of organic matter. When organic matter reached a high concentration, the sensitivity of O-MFC sensor remained at an acceptable level, while that of C-MFC sensor dropped to almost zero. Challenged by a combined shock of organic matter and nitrate, O-MFC sensor delivered evident electrical signals for nitrate warning, while C-MFC failed. Another novel feature of this study lies in a new mathematical model to examine the bioanode process of nitrate monitoring. It revealed that lower capacitance of the bioanode in O-MFC was the major contributor to the improved sensitivity of the device. Copyright © 2018 Elsevier B.V. All rights reserved.

  16. IceTrendr: a linear time-series approach to monitoring glacier environments using Landsat

    Science.gov (United States)

    Nelson, P.; Kennedy, R. E.; Nolin, A. W.; Hughes, J. M.; Braaten, J.

    2017-12-01

    Arctic glaciers in Alaska and Canada have experienced some of the greatest ice mass loss of any region in recent decades. A challenge to understanding these changing ecosystems, however, is developing globally-consistent, multi-decadal monitoring of glacier ice. We present a toolset and approach that captures, labels, and maps glacier change for use in climate science, hydrology, and Earth science education using Landsat Time Series (LTS). The core step is "temporal segmentation," wherein a yearly LTS is cleaned using pre-processing steps, converted to a snow/ice index, and then simplified into the salient shape of the change trajectory ("temporal signature") using linear segmentation. Such signatures can be characterized as simple `stable' or `transition of glacier ice to rock' to more complex multi-year changes like `transition of glacier ice to debris-covered glacier ice to open water to bare rock to vegetation'. This pilot study demonstrates the potential for interactively mapping, visualizing, and labeling glacier changes. What is truly innovative is that IceTrendr not only maps the changes but also uses expert knowledge to label the changes and such labels can be applied to other glaciers exhibiting statistically similar temporal signatures. Our key findings are that the IceTrendr concept and software can provide important functionality for glaciologists and educators interested in studying glacier changes during the Landsat TM timeframe (1984-present). Issues of concern with using dense Landsat time-series approaches for glacier monitoring include many missing images during the period 1984-1995 and that automated cloud mask are challenged and require the user to manually identify cloud-free images. IceTrendr is much more than just a simple "then and now" approach to glacier mapping. This process is a means of integrating the power of computing, remote sensing, and expert knowledge to "tell the story" of glacier changes.

  17. Partial Least Squares Strukturgleichungsmodellierung (PLS-SEM)

    DEFF Research Database (Denmark)

    Hair, Joseph F.; Hult, G. Tomas M.; Ringle, Christian M.

    (PLS-SEM) hat sich in der wirtschafts- und sozialwissenschaftlichen Forschung als geeignetes Verfahren zur Schätzung von Kausalmodellen behauptet. Dank der Anwenderfreundlichkeit des Verfahrens und der vorhandenen Software ist es inzwischen auch in der Praxis etabliert. Dieses Buch liefert eine...... anwendungsorientierte Einführung in die PLS-SEM. Der Fokus liegt auf den Grundlagen des Verfahrens und deren praktischer Umsetzung mit Hilfe der SmartPLS-Software. Das Konzept des Buches setzt dabei auf einfache Erläuterungen statistischer Ansätze und die anschauliche Darstellung zahlreicher Anwendungsbeispiele anhand...... einer einheitlichen Fallstudie. Viele Grafiken, Tabellen und Illustrationen erleichtern das Verständnis der PLS-SEM. Zudem werden dem Leser herunterladbare Datensätze, Aufgaben und weitere Fachartikel zur Vertiefung angeboten. Damit eignet sich das Buch hervorragend für Studierende, Forscher und...

  18. FIB-SEM tomography in biology.

    Science.gov (United States)

    Kizilyaprak, Caroline; Bittermann, Anne Greet; Daraspe, Jean; Humbel, Bruno M

    2014-01-01

    Three-dimensional information is much easier to understand than a set of two-dimensional images. Therefore a layman is thrilled by the pseudo-3D image taken in a scanning electron microscope (SEM) while, when seeing a transmission electron micrograph, his imagination is challenged. First approaches to gain insight in the third dimension were to make serial microtome sections of a region of interest (ROI) and then building a model of the object. Serial microtome sectioning is a tedious and skill-demanding work and therefore seldom done. In the last two decades with the increase of computer power, sophisticated display options, and the development of new instruments, an SEM with a built-in microtome as well as a focused ion beam scanning electron microscope (FIB-SEM), serial sectioning, and 3D analysis has become far easier and faster.Due to the relief like topology of the microtome trimmed block face of resin-embedded tissue, the ROI can be searched in the secondary electron mode, and at the selected spot, the ROI is prepared with the ion beam for 3D analysis. For FIB-SEM tomography, a thin slice is removed with the ion beam and the newly exposed face is imaged with the electron beam, usually by recording the backscattered electrons. The process, also called "slice and view," is repeated until the desired volume is imaged.As FIB-SEM allows 3D imaging of biological fine structure at high resolution of only small volumes, it is crucial to perform slice and view at carefully selected spots. Finding the region of interest is therefore a prerequisite for meaningful imaging. Thin layer plastification of biofilms offers direct access to the original sample surface and allows the selection of an ROI for site-specific FIB-SEM tomography just by its pronounced topographic features.

  19. The Development and Validation of an Instrument to Monitor the Implementation of Social Constructivist Learning Environments in Grade 9 Science Classrooms in South Africa

    Science.gov (United States)

    Luckay, Melanie B.; Laugksch, Rudiger C.

    2015-01-01

    This article describes the development and validation of an instrument that can be used to assess students' perceptions of their learning environment as a means of monitoring and guiding changes toward social constructivist learning environments. The study used a mixed-method approach with priority given to the quantitative data collection. During…

  20. Stimulating innovation for global monitoring of agriculture and its impact on the environment in support of GEOGLAM

    Science.gov (United States)

    Bydekerke, Lieven; Gilliams, Sven; Gobin, Anne

    2015-04-01

    There is an urgent need to ensure food supply for a growing global population. To enable a sustainable growth of agricultural production, effective and timely information is required to support decision making and to improve management of agricultural resources. This requires innovative ways and monitoring methods that will not only improve short-term crop production forecasts, but also allow to assess changes in cultivation practices, agricultural areas, agriculture in general and, its impact on the environment. The G20 launched in June 2011 the "GEO Global Agricultural Monitoring initiative (GEOGLAM), requesting the GEO (Group on Earth Observations) Agricultural Community of Practice to implement GEOGLAM with the main objective to improve crop yield forecasts as an input to the Agricultural Market Information System (AMIS), in order to foster stabilisation of markets and increase transparency on agricultural production. In response to this need, the European Commission decided in 2013 to fund an international partnership to contribute to GEOGLAM and its research agenda. The resulting SIGMA project (Stimulating Innovation for Global Monitoring of Agriculture), a partnership of 23 globally distributed expert organisations, focusses on developing datasets and innovative techniques in support of agricultural monitoring and its impact on the environment in support of GEOGLAM. SIGMA has 3 generic objectives which are: (i) develop and test methods to characterise cropland and assess its changes at various scales; (ii) develop and test methods to assess changes in agricultural production levels; and; (iii) study environmental impacts of agriculture. Firstly, multi-scale remote sensing data sets, in combination with field and other ancillary data, will be used to generate an improved (global) agro-ecological zoning map and crop mask. Secondly, a combination of agro-meteorological models, satellite-based information and long-term time series will be explored to assess crop

  1. A round periodization monitoring of gamma rays in the environment around Daya Bay Nuclear Power Plant

    International Nuclear Information System (INIS)

    Su Qiong; Song Haiqing

    1992-12-01

    The materials of environmental background radiations around a NPP (nuclear power Plant) to be constructed is an important part in the environment effect evaluation report before its operation. The sampling and preparation of samples of air dust and rain water, measuring equipment and analytical method of gamma radionuclides, and a discussion on obtained results in the second round investigation of the two investigations are presented. Comparing with the first round investigation, the sampling places are expanded and improved, especially, a complete and satisfactory data are obtained due to the combination of anti-coincidence shield/anti-Compton HPGe ultra-low γ spectrometer and common HPGe spectrometer. These provides more systematic material to the environmental science research

  2. Study on radon concentration monitoring using activated charcoal canisters in high humidity environments

    International Nuclear Information System (INIS)

    Wang Yuexing; Wang Haijun; Yang Yifang; Qin Sichang; Wang Zhentao; Zhang Zhenjiang

    2009-01-01

    The effects of humidity on the sensitivity using activated charcoal canisters for measuring radon concentrations in high humidity environments were studied. Every canister filled with 80 g of activated charcoal, and they were exposed to 48 h or 72 h in the relative humidity of 68%, 80%, 88% and 96% (28 degree C), respectively. The amount of radon absorbed in the canisters was determined by counting the gamma rays from 214 Pb and 214 Bi (radon progeny). The results showed that counts decreased with the increase of relative humidity. There was a negative linear relationship between count and humidity. In the relative humidity range of 68%-96%, the sensitivity of radon absorption decreased about 2.4% for every 1% (degree)rise in humidity. The results also showed that the exposure time of the activated charcoal canisters should be less than 3 days. (authors)

  3. Current Measurements and Overwash Monitoring Using Tilt Current Meters in Three Coastal Environments

    Science.gov (United States)

    Lowell, N. S.; Sherwood, C. R.; Decarlo, T. M.; Grant, J. R.

    2014-12-01

    Tilt Current Meters (TCMs) provide accurate, cost effective measurements of near-bottom current velocities. Many studies in coastal environments require current measurements, which are frequently made with Acoustic Doppler Profilers (ADPs). ADPs are expensive, however, and may not be suitable for locations where there is significant risk of damage, loss, or theft or where a large spatial array of measurements is required. TCMs, by contrast, are smaller, less expensive, and easier to deploy. This study tested TCMs in three sites to determine their suitability for use in research applications. TCMs are based on the drag-tilt principle, where the instrument tilts in response to current. The meter consists of a buoyant float with an onboard accelerometer, three-axis tilt sensor, three-axis magnetometer (compass), and a data logger. Current measurements are derived by post processing the tilt and compass values and converting them to velocity using empirical calibration data. Large data-storage capacity (4 GB) and low power requirements allow long deployments (many months) at high sample rates (16 Hz). We demonstrate the utility of TCM current measurements on a reef at Dongsha Atoll in the South China Sea, and in Vineyard Sound off Cape Cod, where the TCM performance was evaluated against ADP measurements. We have also used the TCM to record waves during an overwash event on a Cape Cod barrier beach during a winter storm. The TCM recorded waves as they came through the overwash channel, and the data were in agreement with the water-level record used as a reference. These tests demonstrate that TCMs may be used in a variety of near shore environments and have the potential to significantly increase the density of meters in future studies were current measurements are required.

  4. Alternative Landfill Cover and Monitoring Systems for Landfills in Arid Environments

    International Nuclear Information System (INIS)

    Rawlinson, S. E.

    2002-01-01

    In December 2000, a performance monitoring facility was constructed adjacent to the mixed waste disposal unit U-3ax/bl at the Area 3 Radioactive Waste Management Site at the Nevada Test Site. This facility consists of eight drainage lysimeters measuring 10 feet in diameter, 8 feet deep, and backfilled with native soil. The lysimeters have three different surface treatments: two were left bare, two were revegetated with native species, and two were allowed to revegetate with invader species (two are reserved for future studies). The lysimeters are instrumented with an array of soil water content and soil water potential sensors and have sealed bottoms so that any drainage can be measured. All sensors are working properly and indicate that the bare lysimeters are the wettest, as expected. The vegetated lysimeters, both seeded and those allowed to revegetate with invader species, are significantly drier than the bare cover treatments. No drainage has occurred in any of the lysimeters. The Accelerated Site Technology Deployment program under the U.S. Department of Energy's Office of Science and Technology provided the funding for this project with the objective of reducing the uncertainty associated with the performance of monolayer-evapotranspiration waste covers in arid regions such as the one deployed at U-3ax/bl

  5. Optimising the neutron environment of Radiation Portal Monitors: A computational study

    Energy Technology Data Exchange (ETDEWEB)

    Gilbert, Mark R., E-mail: mark.gilbert@ccfe.ac.uk [United Kingdom Atomic Energy Authority, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Ghani, Zamir [United Kingdom Atomic Energy Authority, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); McMillan, John E. [Department of Physics and Astronomy, University of Sheffield, Hicks building, Hounsfield Road, Sheffield S3 7RH (United Kingdom); Packer, Lee W. [United Kingdom Atomic Energy Authority, Culham Science Centre, Abingdon OX14 3DB (United Kingdom)

    2015-09-21

    Efficient and reliable detection of radiological or nuclear threats is a crucial part of national and international efforts to prevent terrorist activities. Radiation Portal Monitors (RPMs), which are deployed worldwide, are intended to interdict smuggled fissile material by detecting emissions of neutrons and gamma rays. However, considering the range and variety of threat sources, vehicular and shielding scenarios, and that only a small signature is present, it is important that the design of the RPMs allows these signatures to be accurately differentiated from the environmental background. Using Monte-Carlo neutron-transport simulations of a model {sup 3}He detector system we have conducted a parameter study to identify the optimum combination of detector shielding, moderation, and collimation that maximises the sensitivity of neutron-sensitive RPMs. These structures, which could be simply and cost-effectively added to existing RPMs, can improve the detector response by more than a factor of two relative to an unmodified, bare design. Furthermore, optimisation of the air gap surrounding the helium tubes also improves detector efficiency.

  6. Radon and thoron monitoring in the environment of Kumaun Himalayas: survey and outcomes

    International Nuclear Information System (INIS)

    Ramola, R.C.; Negi, M.S.; Choubey, V.M.

    2005-01-01

    Monitoring of radon, thoron and their daughter products was carried out in houses of Kumaun Himalaya, India using LR-115 plastic track detectors. The measurements were made in residential houses from June 1999 to May 2000 at a height of 2.5 m from ground level using a twin chamber radon dosimeter. The twin chamber radon dosimeter can record the values of radon, thoron and their decay products separately. Maximum and minimum indoor radon and thoron concentrations were evaluated and activity concentrations of radon and thoron daughters were estimated. The resulting dose rates due to radon, thoron and their decay products varied from 0.04 to 1.89 μSv/h. A detailed analysis of the distribution of radon, thoron and their decay products inside the house is also reported. The observed dose rates inside the houses of Kumaun Himalaya were found to be lower than the ICRP recommended value of 200 Bq/m 3 and thus are within safe limits

  7. Monitoring and Characterization of Miscellaneous Electrical Loads in a Large Retail Environment

    Energy Technology Data Exchange (ETDEWEB)

    Gentile-Polese, L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Frank, S. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sheppy, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lobato, C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Rader, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Long, N. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-02-01

    Buildings account for 40% of primary energy consumption in the United States (residential 22%; commercial 18%). Most (70% residential and 79% commercial) is used as electricity. Thus, almost 30% of U.S. primary energy is used to provide electricity to buildings. Plug loads play an increasingly critical role in reducing energy use in new buildings (because of their increased efficiency requirements), and in existing buildings (as a significant energy savings opportunity). If all installed commercial building miscellaneous electrical loads (CMELs) were replaced with energy-efficient equipment, a potential annual energy saving of 175 TWh, or 35% of the 504 TWh annual energy use devoted to MELs, could be achieved. This energy saving is equivalent to the annual energy production of 14 average-sized nuclear power plants. To meet DOE's long-term goals of reducing commercial building energy use and carbon emissions, the energy efficiency community must better understand the components and drivers of CMEL energy use, and develop effective reduction strategies. These goals can be facilitated through improved data collection and monitoring methodologies, and evaluation of CMELs energy-saving techniques.

  8. Evaluating a radiation monitor for mixed-field environments based on SRAM technology

    CERN Document Server

    Tsiligiannis, G; Bosio, A; Girard, P; Pravossoudovitch, S; Todri, A; Virazel, A; Mekki, J; Brugger, M; Wrobel, F; Saigne, F

    2014-01-01

    Instruments operating in particle accelerators and colliders are exposed to radiations that are composed of particles of different types and energies. Several of these instruments often embed devices that are not hardened against radiation effects. Thus, there is a strong need for mon- itoring the levels of radiation inside the mixed-field radiation areas, throughout different positions. Different metrics exist for measuring the radiation damage induced to electronic devices, such as the Total Ionizing Dose (TID), the Displacement Damage (DD) and of course the fluence of parti- cles for estimating the error rates of the electronic devices among other applications. In this paper, we propose an SRAM based monitor, that is used to define the fluence of High Energy Hadrons (HEH) by detecting Single Event Upsets in the memory array. We evaluated the device by testing it inside the H4IRRAD area of CERN, a test area that reproduces the radiation conditions inside the Large Hadron Collider (LHC) tunnel and its shield...

  9. Monitoring variation in greenhouse gases concentration in urban environment of Delhi.

    Science.gov (United States)

    Sahay, Samraj; Ghosh, Chirashree

    2013-01-01

    Cities across the globe are considered as major anthropogenic sources of greenhouse gases (GHG), yet very few efforts has been made to monitor ambient concentration of GHG in cities, especially in a developing country like India. Here, variations in the ambient concentrations of carbon dioxide (CO(2)) and methane (CH(4)) in residential, commercial, and industrial areas of Delhi are determined from fortnightly daytime observations from July, 2008 to March, 2009. Results indicate that the average daytime ambient concentration of CO(2) varied from 495 to 554 ppm in authorized residential areas, 503 to 621 ppm in the slums or jhuggies in the unauthorized residential areas, 489 to 582 ppm in commercial areas, and 512 to 568 ppm in industrial areas with an average of 541 ± 27 ppm. CH(4) concentration varied from 652 to 5,356 ppbv in authorized residential areas, 500 to 15,220 ppbv in the unauthorized residential areas, 921 to 11,000 ppbv in the commercial areas, and 250 to 2,550 ppbv in the industrial areas with an average of 3,226 ± 1,090 ppbv. A low mid-afternoon CO(2) concentration was observed at most of the sites, primarily due to strong biospheric photosynthesis coupled with strong vertical mixing.

  10. Annual report on radioactive discharges and monitoring of the environment 1978

    International Nuclear Information System (INIS)

    1979-07-01

    The report gives information on radioactive discharges and environmental monitoring for all the Works and Sites of British Nuclear Fuels Ltd. Where a site also encompasses laboratories of the United kingdom Atomic Energy Authority (UKAEA) reference is made to the latter. The report includes assessment of maximum radiological exposures to individual members of the public based on the recommendations of the International Commission on Radiological Protection (ICRP) as advised by the National Radiological Protection Board (NRPB). This year account is taken of new recommendations, ICRP 26, which emphasise the importance of justification and optimisation of practices leading to radiological exposure, and revises the method for evaluating the significance of such exposure. This method recognises that certain consequences of exposure are believed not to occur unless a threshold dose to a particular part of the body is exceeded and that other possible consequences can be evaluated by computing an effective dose equivalent. In both cases limits are stated, the latter being numerically equal to the previous 5 millisievert (500 millirem) per annum whole body dose limit. In addition ICRP comment that it would be prudent to restrict actual continuous exposure over a whole life time to within an average of 1 millisievert (100 millirem) per annum. The assessments are based on data published by NRPB as interim recommendations until ICRP data becomes available. (author)

  11. Stable carbon isotopes to monitor the CO2 source mix in the urban environment

    Science.gov (United States)

    Vogel, F. R.; Wu, L.; Ramonet, M.; Broquet, G.; Worthy, D. E. J.

    2014-12-01

    Urban areas are said to be responsible for approximately 71% of fossil fuel CO2 emissions while comprising only two percent of the land area [IEA, 2008]. This limited spatial expansion could facility a monitoring of anthropogenic GHGs from atmospheric observations. As major sources of emissions, cities also have a huge potential to drive emissions reductions. To effectively manage emissions, cities must however, first establish techniques to validate their reported emission statistics. A pilot study which includes continues 13CO2 data from calibrated cavity ring-down spectrometers [Vogel et al. 2013] of two "sister sites" in the vicinity of Toronto, Canada is contrasted to recent observations of 13CO2 observations in Paris during significant pollution events. Using Miller-Tans plots [Miller and Tans, 2003] for our multi-season observations reveals significant changes of the source signatures of night time CO2 emissions which reflect the importance of natural gas burning in Megacities (up to 80% of fossil fuel sources) and show-case the potential of future isotope studies to determine source sectors. Especially the winter data this approach seems suitable to determine the source contribution of different fuel types (natural gas, liquid fuels and coal) which can inform the interpretation of other Greenhouse Gases and air pollution levels.

  12. Monitoring exposure of personnel to volatile nitrosamines in the laboratory environment

    Energy Technology Data Exchange (ETDEWEB)

    Issenberg, P; Swanson, S E

    1980-01-01

    A convenient sampling method was developed for collection of volatile nitrosamines from large-volume air samples. Stainless steel tubes containing 0.3 g Tenax GC were employed to collect nitrosamines from 5-30 1 air samples. Nitrosamines were eluted from the sample tubes with diethylether to minimize formation of artifacts which were observed when thermal desorption was employed. Eluates were analysed directly by GC-TEA and nitrosamine identities were confirmed using high-resolution GC-MS with selected ion-monitoring. The detection limit was approximately 0.8 micrograms/m3 (0.3 ppb) for NDMA in 2 ml of diethylether extract. The laboratory operations studied included chemical synthesis, trace analysis, animal treatment, microbial mutagenesis tests and in vitro biochemical procedures. In most cases, nitrosamines were not detected in laboratory air, but levels of 200-800 micrograms/m3 (42 to 180 ppb) of N-nitrosomethyl-tert-butylamine were measured during animal treatment, 0.8-8.6 micrograms/m3 (0.3 to 2.8 ppb) of NDMA during mutagenesis assays, 12-22 micrograms/m3 (4-7 ppb) of NDMA during in vitro metabolism studies and 11 micrograms/m3 (3.6 ppb) of NDMA in a walk-in refrigerator. Appropriate corrective measures reduced all nitrosamine levels to below the detection limit. Hamsters and rats treated with NDAA (80 mg/kg, s.c.) excreted 4.4 and 12.9%, respectively, of the nitrosamine in expired air in 24 hr. This route of excretion may be metabolically significant and should be considered in the safe design of animal treatment and holding facilities.

  13. Telemedical systems for home monitoring of patients with chronic conditions in rural environment

    Directory of Open Access Journals (Sweden)

    Marcin Maciejewski

    2014-03-01

    Full Text Available This paper describes the requirements and possible implementations of a telemedical system. The idea of remote patient monitoring is a point of interest for researchers in Poland, and is also in high demand in fields such as diabetology, cardiology, and geriatrics, among others. Aging society, medical care costs and many other factors make remote patient care a promising idea for the future. For each and every condition, a specialized type of sensor must be used to allow specific measurements to be performed. Moreover, a local data storage and communication device must be provided for the sensor to be able to relay data to the station. A smart phone can be used perform such tasks. By implementing such remote diagnostic systems it is possible to collect, process, store and present vital medical data that can be used immediately to perform diagnosis, or later as reference for expert systems. The ‘Borboleta’ and ‘SaguiSaúde’ systems already implemented can serve as a base for system analysis. The systems provide necessary functions and can be used as reference. Many factors contribute to the success of the telemedical system, such as ease of access, scalability, safety, platform independence, and many others. For easier implementation and clarity, the system should be divided into independent layers, which will also make it easier to modify and integrate into other medical systems. Making the system easy to use for patients, medical staff, administrators and data managers makes the task of system design especially challenging. One must decide which information is necessary for each type of user and provide them clearly and in an orderly fashion.

  14. Real time monitoring in-vivo micro-environment through the wound heal mechanism

    Science.gov (United States)

    Yan, Jack

    2013-02-01

    One of the In-vivo system's challenge is real time display the sensing information. Usually Ultrasound, CT, MRI, PET are used to get the internal information, this thesis proposed another approach to address the display challenge. Special nano-particles are in-taken or injected to living subject (usually into blood circulation) to sense and collect psychological information when the active particles pass through the tissues of interest. Using the wound healing mechanism, these activated particles (Information collected) can be drifted out to the wound area and adhibited close to the skin, then skin can show different color if the activated particles are concentrated enough in the specific area to create a skin screen. The skin screen can display the blood status, internal organ's temperature, pressure depending the nano-particles' function and their pathway. This approach can also be used to display in-body video if the particles are sensitive and selective enough. In the future, the skin screen can be bio-computer's monitor. The wound healing in an animal model normally divides in four phase: Hemostasis, Inflammation, Proliferation and Maturation. Hemostasis phase is to form a stable clot sealing the damaged vessel. Inflammation phase causes the blood vessels to become leaky releasing plasma and PMN's (polymorphonucleocytes) into the surrounding tissue and provide the first line of defense against infection. Proliferation phase involves replacement of dermal tissues and sometimes subdermal tissues in deeper wounds as well as contraction of the wound. Maturation phase remodels the dermal tissues mainly by fibroblast to produce greater tensile strength. The skin screen wound will be carefully controlled to be triggered at dermis layer.

  15. Annual report on radioactive discharges and monitoring of the environment 1979

    International Nuclear Information System (INIS)

    1980-07-01

    This report gives information on radioactive discharges through authorised outlets and on environmental monitoring, for all of the British Nuclear Fuel Company's Works and Sites ie the Windscale and Calder Works and the Drigg Storage and Disposal site; Chapelcross Works; Springfields Works and the Ulnes Walton Disposal Site; and Capenhurst Works. Where a site also encompasses laboratories of the United Kingdom Atomic Energy Authority (UKAEA) reference is made to the significance of the discharges from the latter. The report includes assessment of maximum radiological exposures to individual members of the public expressed in terms of limits based on the recommendations of the International Commission on Radiological Protection (ICRP) and in accordance with advice given by the National Radiological Protection Board (NRPB) on the application of the Commission's recommendations in the UK. It is recognised that certain consequences of exposure are believed not to occur unless a threshold dose to a particular part of the body is exceeded and that other possible consequences can be evaluated by computing an effective dose equivalent. In both cases limits are stated, the latter being 5 millisievert (500 millirem) per annum, together with the comment that it would be prudent to restrict actual continuous exposure over a whole lifetime to an average of 1 millisievert (100 millirem) per annum. The assessments are based on data recommended by ICRP. Where these data are not yet available the assessments are based on data published by NRPB as interim recommendations. The percentage of the effective dose equivalent limit is quoted together with the individual contributions to it. Where other limits, which are 'threshold' in nature and cannot be summed, are apparently more restrictive a textual comment is made. (author)

  16. Environment

    International Nuclear Information System (INIS)

    McIntyre, A.D.; Turnbull, R.G.H.

    1992-01-01

    The development of the hydrocarbon resources of the North Sea has resulted in both offshore and onshore environmental repercussions, involving the existing physical attributes of the sea and seabed, the coastline and adjoining land. The social and economic repercussions of the industry were equally widespread. The dramatic and speedy impact of the exploration and exploitation of the northern North Sea resources in the early 1970s, on the physical resources of Scotland was quickly realised together with the concern that any environmental and social damage to the physical and social fabric should be kept to a minimum. To this end, a wide range of research and other activities by central and local government, and other interested agencies was undertaken to extend existing knowledge on the marine and terrestrial environments that might be affected by the oil and gas industry. The outcome of these activities is summarized in this paper. The topics covered include a survey of the marine ecosystems of the North Sea, the fishing industry, the impact of oil pollution on seabirds and fish stocks, the ecology of the Scottish coastline and the impact of the petroleum industry on a selection of particular sites. (author)

  17. Search Engine Marketing (SEM: Financial & Competitive Advantages of an Effective Hotel SEM Strategy

    Directory of Open Access Journals (Sweden)

    Leora Halpern Lanz

    2015-05-01

    Full Text Available Search Engine Marketing and Optimization (SEO, SEM are keystones of a hotels marketing strategy, in fact research shows that 90% of travelers start their vacation planning with a Google search. Learn five strategies that can enhance a hotels SEO and SEM strategies to boost bookings.

  18. Search Engine Marketing (SEM): Financial & Competitive Advantages of an Effective Hotel SEM Strategy

    OpenAIRE

    Leora Halpern Lanz

    2015-01-01

    Search Engine Marketing and Optimization (SEO, SEM) are keystones of a hotels marketing strategy, in fact research shows that 90% of travelers start their vacation planning with a Google search. Learn five strategies that can enhance a hotels SEO and SEM strategies to boost bookings.

  19. Does Sexually Explicit Media (SEM) Affect Me?

    DEFF Research Database (Denmark)

    Hald, Gert Martin; Træen, Bente; Noor, Syed W

    2015-01-01

    and understanding of one’s sexual orientation.First-person effects refer to self-perceived and self-reported effects of SEM consumptionas experienced by the consumer. In addition, the study examined and provided athorough validation of the psychometric properties of the seven-item PornographyConsumption Effect...

  20. SEM: A user's manual for materials science

    International Nuclear Information System (INIS)

    Gabriel, B.L.

    1985-01-01

    This book provides a reference of techniques used by the metallurgical microscopist. It contains an introduction to the instrumentation and methods of scanning electron microscopy with historical as well as state-of-the-art methodologies. Topics covered include: SEM instrumentation, photography, energy dispersive spectroscopy, introduction to sample preparation, polished samples, fracture surfaces, replicas and thin films