Smart Capsules for Lead Removal from Industrial Wastewater.

Science.gov (United States)

Tylkowski, Bartosz; Jastrząb, Renata

2017-04-10

Ground and especially drinking water could be contaminated by heavy metal ions such as lead and chromium, or the metalloid arsenic, discarded from industrial wastewater. These heavy metal ions are regarded as highly toxic pollutants which could cause a wide range of health problems in case of a long-term accumulation in the body. Thus, there have been many efforts to reduce the concentration of lead ions in effluent wastewater. They have included the establishment of stringent permissible discharge levels and management policies, the application of various pollution-control technologies, and the development of adsorbent materials for lead reduction. According to Science [1] encapsulation, developed approximately 65 years ago, has been defined as a major interdisciplinary research technology. Encapsulation has been used to deliver almost everything from advanced drugs to unique consumer sensory experiences. In this chapter we review the art of encapsulation technology as a potential breakthrough solution for a recyclable removal system for lead ions. Moreover, in order to provide the readers with a comprehensive and in-depth understanding of recent developments and innovative applications in this field, we highlight some remarkable advantages of encapsulation for heavy metal remove, such as simplicity of preparation, applicability for a wide range of selective extractants, large special interfacial area, ability for concentration of metal ions from dilute solutions, and less leakage of harmful components to the environment.

Performance of a chevron steam dryer for removal of lead-bismuth droplets

International Nuclear Information System (INIS)

Dostal, Vaclav; Yusibani, Elin; Takahashi, Minoru

2005-01-01

An analysis was performed of a chevron type steam dryer with a trap for the removal of lead-bismuth droplets from steam leaving the Water Boiling Direct Contact Lead or Lead-Bismuth Cooled Reactor. The Lagrangian method was used and is described here. The steam flow field was developed using a CFD code FrontFlow/Red. The simulated dryer performance results were compared to a simple theoretical model from literature. The simulation shown that droplets down to 6 microns in diameter can be completely removed by the steam dryer, which is better than reported earlier in literature. A discrepancy with the theoretical model was found for larger droplets (5 to 10 microns in diameter), where the theoretical model predicted lower removal efficiency. The discrepancy is attributed to be installation of the trap, which is not included in this theoretical model. Some droplets of 1 and 0.5 microns were removed in the dryer as well, which indicates the potential for the fine droplet removal if the trap design is carefully optimized. The investigation of the effect of initial droplet velocity shown that the removal efficiency increases with the increase of the positive velocity components. For larger droplets the effect of initial velocity was found to be minuscule. (author)

Removal of Lead Hydroxides Complexes from Solutions Formed in Silver/Gold: Cyanidation Process

Science.gov (United States)

Parga, José R.; Martinez, Raul Flores; Moreno, Hector; Gomes, Andrew Jewel; Cocke, David L.

2014-04-01

The presence of lead hydroxides in "pregnant cyanide solution" decreases the quality of the Dore obtained in the recovery processes of gold and silver, so it is convenient to remove them. The adsorbent capacity of the low cost cow bone powder was investigated for the removal of lead ions from a solution of lead hydroxide complexes at different initial metal ion concentrations (10 to 50 mg/L), and reaction time. Experiments were carried out in batches. The maximum sorption capacity of lead determined by the Langmuir model was found to be 126.58 mg/g, and the separation factor R L was between 0 and 1, indicating a significant affinity of bone for lead. Experimental data follow pseudo-second order kinetics suggesting chemisorption. It is concluded that cow bone powder can be successfully used for the removal of lead ions, and improves the quality of the silver-gold cyanides precipitate.

Removal of lead and phosphate ions from aqueous solutions by organo-smectite.

Science.gov (United States)

Bajda, Tomasz; Szala, Barbara; Solecka, Urszula

2015-01-01

Smectite has been modified using hexadecyltrimethyl ammonium bromide in an amount of double cationic exchange capacity. This alteration makes it possible to use organo-smectite as a sorbent to remove anionic forms. The experiment consisted of the interchangeable sorption of phosphate(V) and lead(II) by organo-smectite. Research was carried out with varying pH (2-5) and various concentrations (0.1-5 mmol/L). Organo-smectite with previously adsorbed lead ions removed more phosphate than the untreated organo-smectite. Experimental data show that lead is more likely to absorb on the organo-smectite than on the organo-smectite with previously adsorbed phosphate ions. It follows that the most effective use of the organo-smectite is through the sorption of first - Pb cations and then PO4 anions. With an increasing concentration of Pb(II) or P(V), the sorption efficiency increases. The maximum sorption efficiency of lead and phosphate ions is observed at pH 5. This enables the removal of harmful lead and phosphorus compounds from waste water and immobilizes them on the sorbent's surface. The alternating reactions of lead and phosphorus ions result in the crystallization of brompyromorphite Pb5(PO4)3Br.

Enhanced bioremediation of lead-contaminated soil by Solanum nigrum L. with Mucor circinelloides.

Science.gov (United States)

Sun, Liqun; Cao, Xiufeng; Li, Min; Zhang, Xu; Li, Xinxin; Cui, Zhaojie

2017-04-01

Strain selected from mine tailings in Anshan for Pb bioremediation was characterized at the genetic level by internal transcribed spacer (ITS) sequencing. Results revealed that the strain belongs to Mucor circinelloides. Bioremediation of lead-contaminated soil was conducted using Solanum nigrum L. combined with M. circinelloides. The removal efficacy was in the order microbial/phytoremediation > phytoremediation > microbial remediation > control. The bioremediation rates were 58.6, 47.2, and 40.2% in microbial/phytoremediation, microbial remediation, and phytoremediation groups, respectively. Inoculating soil with M. circinelloides enhanced Pb removal and S. nigrum L. growth. The bioaccumulation factor (BF, 1.43), enrichment factor (EF, 1.56), and translocation factor (TF, 1.35) were higher than unit, suggesting an efficient ability of S. nigrum L. in Pb bioremediation. Soil fertility was increased after bioremediation according to change in enzyme activities. The results indicated that inoculating S. nigrum L. with M. circinelloides enhanced its efficiency for phytoremediation of soil contaminated with Pb.

Neighborhood level health risk assessment of lead paint removal activities from elevated steel bridges

Energy Technology Data Exchange (ETDEWEB)

Conway, R.F.; Cohen, J.T.; Bowers, T.

1999-07-01

The New York City Department of Transportation (NYCDOT) has adopted strict containment and monitoring procedures during paint removal activities on its bridges because of the increasing awareness about lead poisoning in children in urban environments and the potential risk of lead-based paint releases during those activities. NYCDOT owns nearly 800 bridges scattered throughout New York City. Before undertaking paint removal activities as part of its ongoing preventive maintenance and rehabilitation program, NYCDOT recently conducted an analysis to determine the public health risk posed to children living near them. The analysis the first of its kind to assess the actual public health risk potential during both routine operations and upset conditions, or accidental releases evaluated the total and incremental blood lead levels from paint removal activities on more than 5,000 children from 6 months to 6 years old. Increases in baseline blood lead levels were estimated using several models, including EPA's Integrated Exposure Uptake Biokinetic (IEUBK) Model. This model estimates steady-state blood lead levels in children, reflecting exposure to lead in multiple media over an extended period of time. Increases in lead exposure from paint removal activities in the area surrounding the bridges was estimated using EPA's Industrial Source Complex (ISC3) model to calculate ambient air and deposition levels. Potential releases from the containment and ancillary equipment used in the paint removal process were modeled based on different release scenarios ranging from routine operations to complete failure of containment. To estimate the paint removal activities' contribution to long-term exterior dust lead levels (and its related interior component), a stochastic simulation model was developed for each block in the study area.

Removing antimony from waste lead storage batteries alloy by vacuum displacement reaction technology.

Science.gov (United States)

Liu, Tiantian; Qiu, Keqiang

2018-04-05

With the wide application of lead acid battery, spent lead acid battery has become a serious problem to environmental protection and human health. Though spent battery can be a contaminant if not handled properly, it is also an important resource to obtain refined lead. Nowadays, the Sb-content in lead storage batteries is about 0.5-3 wt%, which is higher than the Sb-content in the crude lead. However, there are few reports about the process of removing antimony from high-antimony lead bullion. In this study, vacuum displacement reaction technology, a new process for removing antimony from high-antimony lead melts, was investigated. During this process, lead oxide was added to the system and antimony from lead melts was converted into antimony trioxide, which easily was evaporated under vacuum so that antimony was removed from lead melts. The experimental results demonstrated that Sb-content in lead melts decreased from 2.5% to 23 ppm under following conditions: mass ratio of PbO/lead bullion of 0.33, residual gas pressure of 30 Pa, melt temperature of 840 °C, reaction time of 60 min. The distillate gotten can be used as by-product to produce antimony white. Moreover, this study is of importance to recycling of waste lead storage batteries alloy. Copyright © 2018 Elsevier B.V. All rights reserved.

Decay heat removal analyses on the heavy liquid metal cooled fast breeding reactor. Comparisons of the decay heat removal characteristics on lead, lead-bismuth and sodium cooled reactors

International Nuclear Information System (INIS)

Sakai, Takaaki; Ohshima, Hiroyuki; Yamaguchi, Akira

2000-04-01

The feasibility study on several concepts for the commercial fast breeder reactor(FBR) in future has been conducted in JNC for the kinds of possible coolants and fuel types to confirm the direction of the FBR developments in Japan. In this report, Lead and Lead-Bismuth eutectic coolants were estimated for the decay heat removal characteristics by the comparison with sodium coolant that has excellent features for the heat transfer and heat transport performance. Heavy liquid metal coolants, such as Lead and Lead-Bismuth, have desirable chemical inertness for water and atmosphere. Therefore, there are many economical plant proposals without an intermediate heat transport system that prevents the direct effect on a reactor core by the chemical reaction between water and the liquid metal coolant at the hypocritical tube failure accidents in a steam generator. In this study, transient analyses on the thermal-hydraulics have been performed for the decay heat removal events in Equivalent plant' with the Lead, Lead-Bismuth and Sodium coolant by using Super-COPD code. And a resulted optimized lead cooled plant in feasibility study was also analyzed for the comparison. In conclusion, it is become clear that the natural circulation performance, that has an important roll in passive safety characteristic of the reactor, is more excellent in heavy liquid metals than sodium coolant during the decay heat removal transients. However, we need to confirm the heat transfer reduction by the oxidized film or the corrosion products expected to appear on the heat transfer surface in the Lead and Lead-Bismuth circumstance. (author)

Comparison between Removal Efficiency of Slag, zeolite, and Conventional media in slow sand Filter for Removal of Lead and Cadmium from Water Resources

Directory of Open Access Journals (Sweden)

A Ebrahimi

2016-03-01

Full Text Available Introduction: Heavy metals owing to their health hazards and high toxicity in low concentration for human and environment have very concern and attention. Slow sand filter is one of the simple and cost-effective for removal of these pollutants. In this method, media play an important role for removal of pollutant. Therefore, the aim of this study was investigation of different media like slag, zeolite, and conventional media in slow sand filter for removal of lead and cadmium. Methods: In this research there are three beds filter include typical filter bed, slag and zeolite that used in pilot plant for investigation of lead and cadmium removal at three concentration of 0.1T 1 and 10 ppm. Each of filters has an internal diameter of 8 cm and a height of 120 cm with Plexiglas, which have a continuous flow operation. Results: The removal efficiency of turbidity by three typical filter bed, slag, and zeolite with initial turbidity of 13 NTU was 46%, 77%, and 89% respectively. Removal efficiency of lead without turbidity was 70.3%, 79%, and 59.8% respectively for 0.1 ppm lead. For 1 ppm, concentration of lead removal efficiency was 51.8%, 52.7% and 52.6% respectively and for 10 ppm it was 53.4%, 57.8%, and 59.8% respectively. Cadmium removal for these media was 23.4%, 37.5%, and 59.4% respectively at 0.1 ppm cadmium. At 1 ppm of cadmium concentration, it was 37.9%, 45% and 41.3% respectively and at 10 ppm concentration of cadmium it was 68.3%, 68.6% and 67% respectively. Conclusion: Slag and zeolite beds are more efficiently than the conventional sand beds in the slow sand filter, so it can be used instead of the usual sand for removing lead and cadmium from resources water.

Photocatalytic enhancement of cesium removal by Prussian blue-deposited TiO2.

Science.gov (United States)

Kim, Hyuncheol; Kim, Minsun; Kim, Wooyul; Lee, Wanno; Kim, Soonhyun

2018-06-19

After the Fukushima nuclear accident, tremendous efforts were made to treat radiocesium, radiostrontium, and other radioactive materials. For the first time, we demonstrate that a TiO 2 photocatalyst can significantly enhance Cs adsorption by Prussian blue-deposited TiO 2 (PB/TiO 2 ) under UV irradiation. In this study, we synthesized PB/TiO 2 using the photodeposition method. After the Cs ions were adsorbed on the PB/TiO 2 in darkness, we then exposed the PB/TiO 2 to UV light irradiation. This resulted in a further increase in Cs ion adsorption of more than 10 times the amount adsorbed in darkness. This photocatalytic-enhanced adsorption of Cs ions was not observed on PB mixed with SiO 2 , nor under visible light irradiation. We investigated the effects of PB concentration, PB/TiO 2 concentration, and gas purging on both dark and photocatalytic-enhanced adsorption of Cs ions by PB/TiO 2 . Based on the results, we suggest that the photocatalytic-enhanced adsorption of Cs ions on PB/TiO 2 is due to photocatalytic reduction of PB, which leads to additional adsorption of Cs ions. The change in solution color before and after the reaction, and the change in solution pH in the dark and during UV irradiation strongly support this suggestion. The photocatalytic-enhanced adsorption of Cs ions was equivalent during radioactive 137 Cs removal, indicating important applications for pollutant removal from contaminated water. Copyright © 2018 Elsevier B.V. All rights reserved.

A novel surface cleaning method for chemical removal of fouling lead layer from chromium surfaces

International Nuclear Information System (INIS)

Gholivand, Kh.; Khosravi, M.; Hosseini, S.G.; Fathollahi, M.

2010-01-01

Most products especially metallic surfaces require cleaning treatment to remove surface contaminations that remain after processing or usage. Lead fouling is a general problem which arises from lead fouling on the chromium surfaces of bores and other interior parts of systems which have interaction with metallic lead in high temperatures and pressures. In this study, a novel chemical solution was introduced as a cleaner reagent for removing metallic lead pollution, as a fouling metal, from chromium surfaces. The cleaner aqueous solution contains hydrogen peroxide (H 2 O 2 ) as oxidizing agent of lead layer on the chromium surface and acetic acid (CH 3 COOH) as chelating agent of lead ions. The effect of some experimental parameters such as acetic acid concentration, hydrogen peroxide concentration and temperature of the cleaner solution during the operation on the efficiency of lead cleaning procedure was investigated. The results of scanning electron microscopy (SEM) showed that using this procedure, the lead pollution layer could be completely removed from real chromium surfaces without corrosion of the original surface. Finally, the optimum conditions for the complete and fast removing of lead pollution layer from chromium surfaces were proposed. The experimental results showed that at the optimum condition (acetic acid concentration 28% (V/V), hydrogen peroxide 8% (V/V) and temperature 35 deg. C), only 15-min time is needed for complete removal of 3 g fouling lead from a chromium surface.

Roles of extracellular polymeric substances in enhanced biological phosphorus removal process.

Science.gov (United States)

Li, Wen-Wei; Zhang, Hai-Ling; Sheng, Guo-Ping; Yu, Han-Qing

2015-12-01

Enhanced biological phosphorus removal (EBPR) process is known to mainly rely on the ability of phosphorus-accumulating organisms to take up, transform and store excess amount of phosphorus (P) inside the cells. However, recent studies have revealed considerable accumulation of P also in the extracellular polymeric substances (EPS) of sludge, implying a non-negligible role of EPS in P removal by EBPR sludge. However, the contribution of EPS to P uptake and the forms of accumulated extracellular P vary substantially in different studies, and the underlying mechanism of P transformation and transportation in EPS remains poorly understood. This review provides a new recognition into the P removal process in EBPR system by incorporating the role of EPS. It overviews on the characteristics of P accumulation in EPS, explores the mechanism of P transformation and transportation in EBPR sludge and EPS, summarizes the main influential factors for the P-accumulation properties of EPS, and discusses the remaining knowledge gaps and needed future efforts that may lead to better understanding and use of such an EPS role for maximizing P recovery from wastewater. Copyright © 2015 Elsevier Ltd. All rights reserved.

An experimental study on lead removing effect of new chelating agent-FZ-820-4

International Nuclear Information System (INIS)

Feng Jue; Zhang Kangrong; Yin Xieyu; Ji Shaowei

2001-01-01

To evaluate the lead removing effects of F Z-82-4, a new chelating agent, and to compare it with those of DTPA, EDTA, H-73-10 and control group. The experiments are carried out using rats. The Pb-nitrate removing effect of FZ-82-4 was obviously superior to those EDTA, H-73-10 and control group, and equivalent to that of DTPA. According to lead excreting rate of urine in 24 hours. For lead retention rate in bones, liver and kidneys, F Z-82-4 group was lower than control group. The Pb-nitrate removing effect of FZ-82-4 was related to administering time, route and dose

Abnormal contrast enhancement after the removal of meningioma

Energy Technology Data Exchange (ETDEWEB)

Soutsu, M; Hashimoto, T; Yamaguchi, Y; Sekino, H; Nakamura, N [Jikei Univ., Tokyo (Japan). School of Medicine

1980-12-01

Since the introduction of Computerized Tomography (CT) in August, 1976, we have had experience with 20 patients with meningioma. In 10 patients out of the 20, the tumors were removed totally and examined by contrast-enhanced CT pre- and postoperatively. In spite of the total removal of the tumor, however, 5 patients showed an unexpected abnormal enhancement at the operated site after the infusion of a contrast material. These changes were relatively intense, so it was suspected that there were residual tumors. Comparing these 5 cases with the remaining 5 that had no postoperative enhancement, the former cases were shown by operative and angiographical findings to have more adhesion and connecting vessels between tumor and cortex. Since such a postoperative abnormal enhancement is seen along the corticotomy or retracted area after operations for and aneurysm or another lesion, damaged brain tissue was though to be the probable reason for this enhancement. Moreover, the circulatory change caused by cutting the connecting vessels between tumor and cortex was considered to be another reason for the enhancement. This mechanism was also considered to be one reason for the post-meningioma syndrome by El-Banhawy. These postoperative enhancements decreased in density and became obscure within 4 or 8 weeks. Any reappearance of such changes after that period should be examined, carefully to determine whether or not it marks a recurrent tumor.

Lead and chromium removal from leachate using horsetail (Equisetum hyemale

Directory of Open Access Journals (Sweden)

E. Kurniati

2014-01-01

Full Text Available Phytoremediation has been widely used for wastewater treatment technology. Horsetail was investigated for its capacity to remediate lead and chromium in leachate. This plant seemed to be an effective choice for phytoremediation due to its survival in extreme to moderate conditions, the availability of annual or perennial varieties and a deep root system. Conducted in a greenhouse, this research used leachate from final disposal. The leachate was exposed to six treated plants with three multiplications using activated natural zeolite media for one month. The treatments were flow system i.e. batch and continue, and living plants weight that is 0, 153 and 306 g planted in 20 cm diameter and 30 cm deep pots. The leachate pH, temperature, lead, and chromium concentration were observed and also the surrounding temperature and humidity. Results showed that 82.2% of lead can be removed by 153 gram horsetail on batch system as well as 61.2% chromium removal by 153 gram horsetail on continue system. Horsetail seemed to have future to be applied in phytoremediation of artisanal and small scale mining waste.

Enhanced DOC removal using anion and cation ion exchange resins.

Science.gov (United States)

Arias-Paic, Miguel; Cawley, Kaelin M; Byg, Steve; Rosario-Ortiz, Fernando L

2016-01-01

Hardness and DOC removal in a single ion exchange unit operation allows for less infrastructure, is advantageous for process operation and depending on the water source, could enhance anion exchange resin removal of dissolved organic carbon (DOC). Simultaneous application of cationic (Plus) and anionic (MIEX) ion exchange resin in a single contact vessel was tested at pilot and bench scales, under multiple regeneration cycles. Hardness removal correlated with theoretical predictions; where measured hardness was between 88 and 98% of the predicted value. Comparing bench scale DOC removal of solely treating water with MIEX compared to Plus and MIEX treated water showed an enhanced DOC removal, where removal was increased from 0.5 to 1.25 mg/L for the simultaneous resin application compared to solely applying MIEX resin. A full scale MIEX treatment plant (14.5 MGD) reduced raw water DOC from 13.7 mg/L to 4.90 mg/L in the treated effluent at a bed volume (BV) treatment rate of 800, where a parallel operation of a simultaneous MIEX and Plus resin pilot (10 gpm) measured effluent DOC concentrations of no greater than 3.4 mg/L, even at bed volumes of treatment 37.5% greater than the full scale plant. MIEX effluent compared to simultaneous Plus and MIEX effluent resulted in differences in fluorescence intensity that correlated to decreases in DOC concentration. The simultaneous treatment of Plus and MIEX resin produced water with predominantly microbial character, indicating the enhanced DOC removal was principally due to increased removal of terrestrially derived organic matter. The addition of Plus resin to a process train with MIEX resin allows for one treatment process to remove both DOC and hardness, where a single brine waste stream can be sent to sewer at a full-scale plant, completely removing lime chemical addition and sludge waste disposal for precipitative softening processes. Published by Elsevier Ltd.

Biosurfactant-enhanced removal of phenanthrene from soil

NARCIS (Netherlands)

Noordman, WH; Ji, W; Brusseau, ML; Janssen, DB

1997-01-01

The possibility to use rhamnolipid biosurfactants for enhancing the elution of phenanthrene from a soil column was tested. Removal of 90% of the phenanthrene was achieved in a 3.6-fold shorter time period when the feed solution contained 500 mg/L rhamnolipid compared to treatment without

Characterization and lead(II) ions removal of modified Punica granatum L. peels.

Science.gov (United States)

Ay, Çiğdem; Özcan, Asiye Safa; Erdoğan, Yunus; Özcan, Adnan

2017-04-03

The aim of the present study was to enhance the biosorption capacity of a waste biomass of Punica granatum L. peels (PGL) using various chemical modification agents. Among these agents, hexamethylenediamine (HMDA) indicated the best performance with regard to the improvement of lead(II) ions removal from aqueous solution. The characterization of HMDA-modified P. granatum L. peels (HMDA-PGL) was achieved by using elemental analysis, FT-IR, thermogravimetric (TG) analysis and zeta potential measurement techniques. Based on FT-IR study, the chemical modification of P. granatum L. peels take place with its carboxyl, carbonyl, hydroxyl, etc. groups and these groups are responsible for the biosorption of lead(II) ions onto modified biomass. Biosorption equilibrium and kinetic data fitted well the Langmuir isotherm and the pseudo-second-order kinetic models, respectively. The highest biosorption capacity obtained from Langmuir isotherm model was 371.36 mg g -1 . Biosorption process was spontaneous and endothermic in nature according to the thermodynamic results and it quickly reached the equilibrium within 60 minutes. The validity of kinetic models used in this study can be quantitatively tested by using a normalized standard deviation Δq(%).

A low sludge generated anode by hybrid solar electrocoagulation for the removal of lead

Science.gov (United States)

Hussin, F.; Aroua, M. K.

2017-06-01

In this work, perforated zinc is proposed as a new anode for lead removal by hybrid solar electrocoagulation. The characteristics of the sludge were investigated to understand the behaviour of lead removal during electrocoagulation. Sludge products formed were characterised using X-ray diffraction (XRD), X-ray fluorescence (XRF) and Field Emission Scanning Electron Microscopy (FESEM). In addition, the pH variation during electrocoagulation and effects on the sludge products were examined. At optimum conditions showed that the perforated zinc electrode produced better performance with high removal efficiency, low sludge volume index and less energy consumption.

Removing chromium and lead metals using phytoremediation technique

Directory of Open Access Journals (Sweden)

Al-Anbari Riyad

2018-01-01

Full Text Available Phytoremediation technique uses plants parts to remove, extract, and absorb heavy or toxic matter from soil and water. In the present study, Catharanthusroseus (Periwinkle and Nerium Oleander (Oleander were used for removing Chromium (Cr and Lead (Pb metals. These plant species were seeded in polyethylene pots containing 8kg of soil. Each pot was irrigated with wastewater for four months (May, June, July and August and accumulation of the considered metals was analyzed after every month for leaf, stem and root by using Atomic Absorption Spectrophotometer (AAS. This experimental work was carried out in the laboratories of Water Desalination Researches Unit - Building and Construction Engineering Department and Environmental Research Centre at the University of Technology in Baghdad City, Iraq. The concentration of Cr was found to be increased with time. High Cr concentration, 20.34 mg/kg, was recorded at August in leaf of Periwinkle and 19.61 mg/kg in root of Oleander in case of using 100% wastewater (WW. While, for Pb, the maximum concentration, 22 mg/kg, was recorded in June in leaf of Periwinkle and 19.5 mg/kg in steam of Oleander. Accordingly, Oleander has the maximum removal efficiency.

Reactivity enhancement of iron sulfide nanoparticles stabilized by sodium alginate: Taking Cr (VI) removal as an example

Energy Technology Data Exchange (ETDEWEB)

Wu, Jun; Wang, Xian-Bin; Zeng, Raymond J., E-mail: rzeng@ustc.edu.cn

2017-07-05

Highlights: • Sodium alginate can be used to stabilize FeS nanoparticles. • FeS-SA enhances Cr(VI) removal efficiency from 65% to 100% compared to naked FeS. • Reduction and adsorption respectively account for 82% and 18% of Cr removal by FeS-SA. • Analysis of reaction products reveals the co-existence of α-FeOOH, S{sub 8}, and Cr(OH){sub 3.} - Abstract: The widespread distribution of chromium(VI) in the environment leads to groundwater contamination. The use of iron sulfide (FeS) to remove Cr(VI) has therefore been proposed. However, aggregation is one of the main problems associated with the use of FeS nanoparticles prepared by traditional methods In this study, we used sodium alginate (SA) to stabilize FeS nanoparticles (FeS-SA). SA could prevent aggregation of FeS by the concurrent electrostatic repulsion and steric hindrance. Homogeneously dispersed FeS-SA nanoparticles 100 nm in diameter were observed. FeS-SA showed high efficiency in Cr(VI) removal, corresponding to an enhancement of efficiency from 65% (7.50 mmol Cr(VI) per g FeS) to 100% (11.54 mmol Cr per g FeS) relative to that achieved with naked FeS. Analysis of reaction products by X-ray diffraction and X-ray photoelectron spectroscopy revealed the co-existence of α-FeOOH, S{sub 8}, and Cr(OH){sub 3} that apparently were introduced by Fe(II), S(−II), and Cr(VI), respectively. In-depth analysis of the removal mechanism revealed that reduction and adsorption respectively account for 82% and 18% of the Cr removal. In addition, higher pH and CaCl{sub 2} concentration resulted in lower removal efficiency. This study provides a promising application of SA in enhancing FeS reactivity for the remediation of groundwater pollution.

Removal of lead, mercury and nickel using the yeast Saccharomyces cerevisiae

Directory of Open Access Journals (Sweden)

Cherlys Infante J.

2014-06-01

Full Text Available Objective. In this study the biomass of the yeast Saccharomyces cerevisiae was used to remove lead, mercury and nickel in the form of ions dissolved in water. Materials and methods. Synthetic solutions were prepared containing the three heavy metals, which were put in contact with viable microorganisms at different conditions of pH, temperature, aeration and agitation. Results. Both individual variables and the interaction effects influenced the biosorption process. Throughout the experimental framework it was observed that the biomass of Saccharomyces cerevisiae removed a higher percentage of lead (86.4% as compared to mercury and nickel (69.7 and 47.8% respectively. When the pH was set at a value of 5 the effect was positive for all three metals. Conclusions. pH was the variable that had a greater influence on the biosorption of lead on the biomass of Saccharomyces cerevisiae. The affinity of the heavy metals for the biomass followed the order Pb>Hg>Ni.

A simplified in-situ electrochemical decontamination of lead from polluted soil (abstract)

International Nuclear Information System (INIS)

Ansari, T.M.; Ahmad, I.; Khan, Q.M.; Chaudhry, A.H.

2011-01-01

This paper reports a simplified In-Situ electrochemical method for remediation of field soil contaminated with lead. A series of electrochemical decontamination experiments including variable conditions such as operating duration and application of enhancement reagent were performed to demonstrate the efficiency of lead removal from spiked and polluted soil samples collected from Lahore, Pakistan. The results showed that the efficiency of lead removal from the contaminated soil increased with increasing the operating duration under a set of experimental conditions. The reagent used as complexing and solubilizing agent i.e. EDTA was found to be efficient in removing lead from the polluted soil. After 15 days duration, 85 % lead removal efficiency was observed in spiked soil under enhanced conditions , however, 63 % lead removal was achieved from the polluted soil samples by the simplified In-situ electrochemical decontamination method. The method is simple, rapid, cheaper and suitable for soil remediation purposes. (author)

Lead recovery and glass microspheres synthesis from waste CRT funnel glasses through carbon thermal reduction enhanced acid leaching process.

Science.gov (United States)

Mingfei, Xing; Yaping, Wang; Jun, Li; Hua, Xu

2016-03-15

In this study, a novel process for detoxification and reutilization of waste cathode ray tube (CRT) funnel glass was developed by carbon thermal reduction enhanced acid leaching process. The key to this process is removal of lead from the CRT funnel glass and synchronous preparation of glass microspheres. Carbon powder was used as an isolation agent and a reducing agent. Under the isolation of the carbon powder, the funnel glass powder was sintered into glass microspheres. In thermal reduction, PbO in the funnel glass was first reduced to elemental Pb by carbon monoxide and then located on the surface of glass microspheres which can be removed easily by acid leaching. Experimental results showed that temperature, carbon adding amount and holding time were the major parameters that controlled lead removal rate. The maximum lead removal rate was 94.80% and glass microspheres that measured 0.73-14.74μm were obtained successfully by setting the temperature, carbon adding amount and holding time at 1200°C, 10% and 30min, respectively. The prepared glass microspheres may be used as fillers in polymer materials and abrasive materials, among others. Accordingly, this study proposed a practical and economical process for detoxification and recycling of waste lead-containing glass. Copyright © 2015 Elsevier B.V. All rights reserved.

In-situ Lead Removal by Iron Nano Particles Coated with Nickel

Directory of Open Access Journals (Sweden)

Mohammadreza Fadaei-tehrani

2016-01-01

Full Text Available This study investigates the potential of nano-zero-valent iron particles coated with nickel in the removal of lead (Pb2+ from porous media. For this purpose, the nano-particles were initially synthesized and later stablilized using the strach biopolymer prior to conducting batch and continuous experiments. The results of the batch experiments revealed that the reaction kinetics fitted well with the pseudo-first-order adsorption model and that the reaction rate ranged from 0.001 to 0.035 g/mg/min depending on solution pH and the molar ratio of Fe/Pb. Continuous experiments showed that lead remediation was mostly influenced not only by seepage velocity but also by the quantity and freshness of nZVI as well as the grain type of the porous media. Maximum Pb2+ removal rates obtained in the batch and lab models were 95% and 80%, respectively. Based on the present study, S-nZVI may be suggested as an efficient agent for in-situ remediation of groundwater contaminated with lead.

Removal of lead (II) from aqueous solutions using rice straw.

Science.gov (United States)

Amer, Hayam; El-Gendy, Ahmed; El-Haggar, Salah

2017-09-01

Lead (Pb 2+ ) is a heavy metal which is utilized in several industries and can have severe impact on the environment and human health. Research work has been carried out lately on the feasibility of using various low cost materials in the removal of heavy metals from wastewater. In this study, the feasibility of utilizing raw rice straw for removal of Pb 2+ from water through biosorption was investigated using batch equilibrium experiments. The effect of several operating parameters on the removal of Pb 2+ using rice straw was studied, revealing the optimum parameters at an initial Pb 2+ concentration of 40 mg/l were: 30 min contact time at a pH of 5.5, particle size 75-150 μm and a dose of 4 g/l. A maximum removal of 94% was achieved under optimum conditions. Langmuir and Freundlich isotherm models were used for the evaluation of the equilibrium experimental data. The maximum adsorption capacity of rice straw calculated using the Langmuir isotherm was 42.55 mg/g.

Enhanced removal of Methylene Blue by electrocoagulation using iron electrodes

Directory of Open Access Journals (Sweden)

Mohamed S. Mahmoud

2013-06-01

Full Text Available The removal of pollutants from effluents by electrocoagulation has become an attractive method in recent years. The study deals with the enhancement of removal of Methylene Blue dye by using an electromagnetic field during the electrocoagulation process. Effects of electrolyte concentration, dye concentration, intensity and the direction of the electromagnet on the decolorization efficiency have been investigated. The formed ferric hydroxide flocs trap colloidal particles and make solid–liquid separation easier during the next stage. The electrocoagulation stages must be optimized in order to design an economically feasible process. The results showed that the optimum electrolysis was 10–20 min at a current density of 8 mA/cm2, while the optimum concentration of the electrolyte (NaOH was found to be 2 wt.% when the dye concentration was 50 mg/L. The utilization of an electromagnetic field enhanced the dye removal due to the induced motion of paramagnetic ions inside the solution. The power consumption required to remove the dye was reduced by 45% in the case of applying an electromagnetic field.

Removal of Lead from Water Using Calcium Alginate Beads Doped with Hydrazine Sulphate-Activated Red Mud as Adsorbent

Directory of Open Access Journals (Sweden)

A. Naga Babu

2017-01-01

Full Text Available Calcium alginate beads doped with hydrazine sulphate-treated red mud are investigated as adsorbent for extracting lead ions from water using batch methods of extraction. Different extraction conditions are optimised for maximum lead extraction. Substantial amount of lead is removed, and the adsorption ability is found to be 138.6 mg/g. Surface characterization using FTIR, EDX, and FESEM confirms that lead is “onto” the surface of the adsorbent. Thermodynamic parameters, adsorption isotherms, and kinetics of adsorption are analysed. Adsorption is “physisorption” in nature and spontaneous. The adsorbent developed can be regenerated using 0.1 M HCl. Thus regenerated adsorbent can be used as the adsorbent for further removal of lead at least 10 times, and this enables the complete removal of lead from water by repetitive use of the regenerated adsorbent. The beads facilitate the easy filtration. The methodology developed is successfully applied for removing lead from industrial waste waters.

Removal of lead ions from industrial waste water by using biomaterials – a novel method

Directory of Open Access Journals (Sweden)

Malairajan Singanan

2005-12-01

Full Text Available A simple cost effective and eco-friendly method for the remediation of lead from industrial wastewater has been investigated. A novel biomaterial, Tridax procumbens (Asteraceae a medicinal plant, was used for the removal of lead ions from synthetic wastewater and the method was also applied for real sample analysis. The operational pH of the experimental solution was fixed as 4.5. The optimum amount of bioadsorbent was 3.5 g. The Pb(II ions removal efficiency of the raw bioadsorbent was also determined. The removal efficiency of the activated carbon of the bioadsorbent was excellent. 98 % removal of Pb(II ions was achieved at the dose rate of 3.5 g. The optimum contact time was estimated to be 160 minutes.

Removal of lead and fluoride from contaminated water using exhausted coffee grounds based bio-sorbent.

Science.gov (United States)

Naga Babu, A; Reddy, D Srinivasa; Kumar, G Suresh; Ravindhranath, K; Krishna Mohan, G V

2018-07-15

Water pollution by industrial and anthropogenic actives has become a serious threat to the environment. World Health Organization (WHO) has identified that lead and fluoride amid the environmental pollutants are most poisonous water contaminants with devastating impact on the human race. The present work proposes a study on economical bio-adsorbent based technique using exhausted coffee grounds in the removal of lead and fluoride contaminants from water. The exhausted coffee grounds gathered from industrial wastes have been acid-activated and examined for their adsorption capacity. The surface morphology and elemental characterization of pre-and-post adsorption operations by FESEM, EDX and FTIR spectral analysis confirmed the potential of the exhausted coffee ground as successful bio-sorbent. However, thermodynamic analysis confirmed the adsorption to be spontaneous physisorption with Langmuir mode of homogenous monolayer deposition. The kinetics of adsorption is well defined by pseudo second order model for both lead and fluoride. A significant quantity of lead and fluoride is removed from the synthetic contaminated water by the proposed bio-sorbent with the respective sorption capabilities of 61.6 mg/g and 9.05 mg/g. However, the developed bio-sorbent is also recyclable and is capable of removing the lead and fluoride from the domestic and industrial waste-water sources with an overall removal efficiency of about 90%. Copyright © 2018 Elsevier Ltd. All rights reserved.

Nanomagnet-based removal of lead and digoxin from living rats

Science.gov (United States)

Herrmann, Inge K.; Schlegel, Andrea; Graf, Rolf; Schumacher, Christoph M.; Senn, Nico; Hasler, Melanie; Gschwind, Sabrina; Hirt, Ann-Marie; Günther, Detlef; Clavien, Pierre-Alain; Stark, Wendelin J.; Beck-Schimmer, Beatrice

2013-08-01

In a number of clinical conditions such as intoxication, bacteraemia or autoimmune diseases the removal of the disease-causing factor from blood would be the most direct cure. However, physicochemical characteristics of the target compounds limit the applicability of classical filtration and diffusion-based processes. In this work, we present a first in vivo magnetic blood purification rodent animal model and demonstrate its ability to rapidly clear toxins from blood circulation using two model toxins with stable plasma levels (lead (Pb2+) and digoxin). Ultra-strong functionalized metal nanomagnets are employed to eliminate the toxin from whole blood in an extracorporeal circuit. In the present experimental demonstration over 40% of the toxin (i.e. lead or digoxin) was removed within the first 10 minutes and over 75% within 40 minutes. After capturing the target substance, a magnetic trap prevents the toxin-loaded nanoparticles from entering the blood circulation. Elemental analysis and magnetic hysteresis measurements confirm full particle recovery by simple magnetic separation (residual particle concentration below 1 μg mL-1 (detection limit)). We demonstrate that magnetic separation-based blood purification offers rapid blood cleaning from noxious agents, germs or other deleterious materials with relevance to a number of clinical conditions. Based on this new approach, current blood purification technologies can be extended to efficiently remove disease-causing factors, e.g. overdosed drugs, bacteria or cancer cells without being limited by filter cut-offs or column surface saturation.

Removal of arsenic from contaminated water using coagulation enhanced microfiltration

International Nuclear Information System (INIS)

Volchek, K.; Velicogna, D.; Dumouchel, A.; Wong, W.P.; Brown, C.E.

2002-01-01

Results of an innovative arsenic removal process were presented. The process is based on a combination of coagulation and microfiltration processes. Coagulation-Enhanced Microfiltration (CEMF) may eventually become a full-scale commercial technology. This study focused on the process with respect to groundwater treatment because of the importance of arsenic contamination in drinking water. Most experiments were bench-scale using tap water spiked with arsenic. Ferric chloride, which is commonly used in arsenic removal processes was also added. In addition, some tests were conducted on actual arsenic-contaminated water from the effluent treatment plant of a former mining site in Ontario. Results indicate a high arsenic removal efficiency in both spiked and actual water solutions. The microfiltration significantly reduced the level of arsenic in the treatment. This paper described the characteristics of membrane separation. It also presented information regarding chemically enhanced membrane filtration and coagulation-enhanced microfiltration. Bench-scale tests were conducted with both tubular membranes and with immersed capillary membranes. The effect of iron to arsenic ratios on the effectiveness of the system was also tested. It was recommended that future research should include a field study of the process on a pilot-scale to optimize process parameters and to accurately determine the cost of the process. 16 refs., 8 tabs., 9 figs

Products of radiation removal of lead from aqueous solutions

International Nuclear Information System (INIS)

Drtinova, Barbora; Pospisil, Milan

2008-01-01

Full text: Some metal ions, including Pb 2+ can be gradually reduced by primary reducing products of water radiolysis (solvated electrons e aq - and H radicals) to insoluble, easily separable metals. Conditions of water remediation using irradiation with accelerated electrons were studied. The solutions with initial concentration 100 mg/L of Pb(II) (originally nitrate) containing OH radical scavengers were irradiated under intensive agitation in sealed thin-glass ampoules by accelerated electrons (4.5 MeV) from a linear accelerator. Doses ranging from 0.5 to 60 kGy (dose rate of 0.5 kGy/s) determined by an alanine dosimeter were applied. Subsequent process of centrifugation (5000 revs per minute) was used for the separation of product- finely dispersed particles. The changes in metal concentration were determined with error ± 3% by means of atomic absorption spectroscopy with flame atomization. The solid products formed after the irradiation were analyzed by both thermogravimetry and differential thermal analysis. For the pre-irradiated systems were carried out calculations by using PHREEQC in order to determinate the speciation. Without addition of an OH radical scavenger the radiation-induced removal of lead did not occur. The influence of potassium formate HCOOK (1x10 -3 - 4x10 -2 mol/L) and 10% isopropanol as typical OH radical scavengers was individually studied. The lead can be completely removed from aqueous solutions (pH about 5-6) containing 1x10 - :2 mol/L of HCOOK already at the dose of 2.5 kGy. With increasing concentration of HCOOK (1x10 -3 - 4x10 -2 mol/L) increases the amount of Pb(HCOO) + form in the solution before irradiation. The radiation product is metallic lead at low concentration of HCOOK to PbCO 3 at higher concentration of the OH radical scavenger. In the system with isopropanol dominates the form Pb 2+ and the product of radiation reduction is then metallic lead

Enhanced removal of Methylene Blue by electrocoagulation using iron electrodes

OpenAIRE

Mohamed S. Mahmoud; Joseph Y. Farah; Taha E. Farrag

2013-01-01

The removal of pollutants from effluents by electrocoagulation has become an attractive method in recent years. The study deals with the enhancement of removal of Methylene Blue dye by using an electromagnetic field during the electrocoagulation process. Effects of electrolyte concentration, dye concentration, intensity and the direction of the electromagnet on the decolorization efficiency have been investigated. The formed ferric hydroxide flocs trap colloidal particles and make solid–liqui...

Enhancing arsenic removal from groundwater at household level with naturally occurring iron

Directory of Open Access Journals (Sweden)

Anitha Kumari Sharma

2016-06-01

Full Text Available A supply of drinking water low in Arsenic (As prevents arsenic poisoning. The presence of high concentrations of iron (Fe in groundwater under the alluvial plains of the large rivers in Southeast Asia is a prerequisite for the simple removal of As. This study investigated the mechanisms and possibilities for enhancing As removal with naturally occurring Fe in a reliable, low cost and sustainable way. The results of the study show that As removal with Fe is greatly enhanced by the addition of an oxidizing agent (preferably KMnO4 immediately after the pumping of groundwater. Further enhancement of As removal in the presence of Fe can be achieved by adding a small volume of a concentrated basic solution of MnO4- and AlO2-, which has a combined oxidation, coagulation and buffering capacity. Best results were obtained when this solution was mixed with the groundwater immediately after its pumping until a pale pink color appeared. Maximum required reaction time was 10 minutes and subsequent filtration of the water was able to reduce the As concentration to near zero. Concentrations of MnO4- and AlO2- can be varied in the solution to achieve sufficient As removal to suit different Fe/As ratios and the presence of interfering co-occurring anions.

Calcium carbonate in the removal of iron and lead from dilute waste water

Energy Technology Data Exchange (ETDEWEB)

Hautala, E; Randall, J; Goodban, A; Waiss, A Jr

1977-01-01

The utility of powdered CaCO/sub 3/ in the removal of lead and iron from dilute aqueous waste waters has been demonstrated and the results successfully applied to treat industrial waste water from a lead battery plant. The reclaimed water is suitable for recycling to the plant and is now being utilized with consequent economic advantages.

THIOGLYCOLIC ACID ESTERIFIED IN TO RICE STRAW FOR REMOVING LEAD FROM AQUEOUS SOLUTION

Directory of Open Access Journals (Sweden)

R. Gong

2011-09-01

Full Text Available Thiol rice straw (TRS was prepared by esterifying thioglycolic acid onto rice straw in the medium of acetic anhydride and acetic acid with sulfuric acid as catalyst. The sorption of lead (Pb on TRS from aqueous solution was subsequently investigated. The batch experiments showed that Pb removal was dependent on initial pH, sorbent dose, Pb concentration, contact time, and temperature. The maximum value of Pb removal appeared at pH 5. For 100 mg/L of Pb solution, a removal ratio of greater than 98% could be achieved with 2.0 g/L or more of TRS. The isothermal data of Pb sorption conformed well to the Langmuir model, and the maximum sorption capacity (Qm of TRS for Pb was 104.17 mg/g. The equilibrium of Pb removal was reached within 120 min. The Pb removal process could be described by the pseudo-first-order kinetic model. The thermodynamic study indicated that the Pb removal process was spontaneous and endothermic.

Isolation and Identification of Cadmium and Lead Resistant Bacteria and their Bacterial Removal from Wastewater

Directory of Open Access Journals (Sweden)

Sanaz Abbasi

2017-01-01

Full Text Available Municipal and industrial effluents continually release into the environment heavy metals of a variety of physical and chemical forms and at various concentrations. Biological treatment processes have attracted a growing attention for the removal of heavy metals from these effluents. For the purposes of the present study, bacteria that are relatively resistant to heavy metals, such as cadmium and lead, were isolated from municipal waste and purified. They were then subjected to biochemical tests for identification and their minimum inhibitory concentrations were determined. Bacterial minimum inhibitory concentrations were initially measured in flasks containing 25, 50, 75, 100, 150, 300, 500, and 700 ppm of lead and cadmium before superior bacteria at populations of 108 CFU/ml were evaluated in terms of their ability to remove lead and cadmium at concentrations of 50, 100, 150, and 300 ppm from enriched municipal wastewater. Base on the results, Bacillus laterosporous and Yersinia pseudotuberculosis were identified as the resistant bacteria and the minimum lead and cadmium inhibitory concentrations for these bacteria were determined to be 300 and 500 ppm, respectively. Moreover, Bacillus laterosporous and Yersinia pseudotuberculosis recorded maximum removal efficiencies of around 50.6% and 45.7%, respectively, with wastewater containing 100 mg/l of lead and 36.18% and 21.41% in the case of cadmium from wastewater enriched with 100 mg/l of lead and 150 mg/l of cadmium.

Laser Monitoring Of Phytoextraction Enhancement Of Lead Contaminated Soil Adopting EDTA And EDDS

Science.gov (United States)

Hassan, M.; Abdelhamied, M.; Hanafy, A. H.; Fantoni, R.; Harith, M. A.

2011-09-01

Removal of heavy metals (HMs) such as Pb from soil, wastewater, and air is essential for environment and human health. Phytoremediation is a well established technology based on the use of certain green plants for contaminants removal from soil, wastewater as well as air. Scented geranium, Pelargonium zonal, is a flowering plant recently used in HMs removal from contaminated soil. In the present work, EDTA (ethylenediaminetetraacetic acid) and EDDS (S, S-ethylenediaminedisuccinic acid) were used as chemical assistants providing higher Pb availability for extraction by plant roots. Lead was artificially added to the planting media, peatmoss, at different concentrations. Laser induced breakdown spectroscopy (LIBS) was used to follow up Pb relative concentrations in peatmoss as well as plant shoots, at different sampling times during the experiment period. Laser induced chlorophyll fluorescence (LICF), has been also used to evaluate chlorophyll formation and photosynthetic apparatus status in geranium plants. Such measurements were performed on geranium plants grown under various Pb levels, as well as EDTA and EDDS combinations. The combined effect of EDTA and EDDS was found to enhance Pb extraction with time. Good correlation was found between LICF results and chlorophyll (a) (Chl.a) concentrations in plant tissues extracted by chemical analysis.

Effect of pH on lead removal from water using tree fern as the sorbent.

Science.gov (United States)

Ho, Yuh-Shan

2005-07-01

The sorption of lead from water onto an agricultural by-product, tree fern, was examined as a function of pH. The sorption processes were carried out using an agitated and baffled system. Pseudo-second-order kinetic analyses were performed to determine the rate constant of sorption, the equilibrium sorption capacity, and the initial sorption rate. Application of the pseudo-second-order kinetics model produced very high coefficients of determination. Results showed the efficiency of tree fern as a sorbent for lead. The optimum pH for lead removal was between 4 and 7, with pH 4.9 resulting in better lead removal. Ion exchange occurred in the initial reaction period. In addition, a relation between the change in the solution hydrogen ion concentration and equilibrium capacity was developed and is presented.

Potential and costs of carbon dioxide removal by enhanced weathering of rocks

Science.gov (United States)

Strefler, Jessica; Amann, Thorben; Bauer, Nico; Kriegler, Elmar; Hartmann, Jens

2018-03-01

The chemical weathering of rocks currently absorbs about 1.1 Gt CO2 a-1 being mainly stored as bicarbonate in the ocean. An enhancement of this slow natural process could remove substantial amounts of CO2 from the atmosphere, aiming to offset some unavoidable anthropogenic emissions in order to comply with the Paris Agreement, while at the same time it may decrease ocean acidification. We provide the first comprehensive assessment of economic costs, energy requirements, technical parameterization, and global and regional carbon removal potential. The crucial parameters defining this potential are the grain size and weathering rates. The main uncertainties about the potential relate to weathering rates and rock mass that can be integrated into the soil. The discussed results do not specifically address the enhancement of weathering through microbial processes, feedback of geogenic nutrient release, and bioturbation. We do not only assess dunite rock, predominantly bearing olivine (in the form of forsterite) as the mineral that has been previously proposed to be best suited for carbon removal, but focus also on basaltic rock to minimize potential negative side effects. Our results show that enhanced weathering is an option for carbon dioxide removal that could be competitive already at 60 US  t-1 CO2 removed for dunite, but only at 200 US  t-1 CO2 removed for basalt. The potential carbon removal on cropland areas could be as large as 95 Gt CO2 a-1 for dunite and 4.9 Gt CO2 a-1 for basalt. The best suited locations are warm and humid areas, particularly in India, Brazil, South-East Asia and China, where almost 75% of the global potential can be realized. This work presents a techno-economic assessment framework, which also allows for the incorporation of further processes.

Enhanced coagulation for turbidity and Total Organic Carbon (TOC) removal from river Kansawati water.

Science.gov (United States)

Narayan, Sumit; Goel, Sudha

2011-01-01

The objective of this study was to determine optimum coagulant doses for turbidity and Total Organic Carbon (TOC) removal and evaluate the extent to which TOC can be removed by enhanced coagulation. Jar tests were conducted in the laboratory to determine optimum doses of alum for the removal of turbidity and Natural Organic Matter (NOM) from river water. Various other water quality parameters were measured before and after thejar tests and included: UV Absorbance (UVA) at 254 nm, microbial concentrations, TDS, conductivity, hardness, alkalinity, and pH. The optimum alum dose for removal of turbidity and TOC was 20 mg/L for the sample collected in November 2009 and 100 mg/L for the sample collected in March 2010. In both cases, the dose for enhanced coagulation was significantly higher than that for conventional coagulation. The gain in TOC removal was insignificant compared to the increase in coagulant dose required. This is usual for low TOC (TOC need to be tested to demonstrate the effectiveness of enhanced coagulation.

Study of Modern Nano Enhanced Techniques for Removal of Dyes and Metals

Directory of Open Access Journals (Sweden)

Samavia Batool

2014-01-01

Full Text Available Industrial effluent often contains the significant amount of hexavalent chromium and synthetic dyes. The discharge of wastewater without proper treatment into water streams consequently enters the soil and disturbs the aquatic and terrestrial life. A range of wastewater treatment technologies have been proposed which can efficiently reduce both Cr(VI and azo dyes simultaneously to less toxic form such as biodegradation, biosorption, adsorption, bioaccumulation, and nanotechnology. Rate of simultaneous reduction of Cr(VI and azo dyes can be enhanced by combining different treatment techniques. Utilization of synergistic treatment is receiving much attention due to its enhanced efficiency to remove Cr(VI and azo dye simultaneously. This review evaluates the removal methods for simultaneous removal of Cr(VI and azo dyes by nanomicrobiology, surface engineered nanoparticles, and nanophotocatalyst. Sorption mechanism of biochar for heavy metals and organic contaminants is also discussed. Potential microbial strains capable of simultaneous removal of Cr(VI and azo dyes have been summarized in some details as well.

Enhanced xylene removal by photocatalytic oxidation using fiber-illuminated honeycomb reactor at ppb level

International Nuclear Information System (INIS)

Wu, Yi-Ting; Yu, Yi-Hui; Nguyen, Van-Huy; Lu, Kung-Te; Wu, Jeffrey Chi-Sheng; Chang, Luh-Maan; Kuo, Chi-Wen

2013-01-01

Graphical abstract: We have designed a fiber-illuminated honeycomb reactor (FIHR) in which the removal efficiency of m-xylene is significantly enhanced to 96.5% as compared to 22.0% for UV irradiation only. The results indicate that photocatalysts not only play the role to substantially oxidize m-xylene, but also alter the chemical properties of xylene under UV illumination. -- Highlights: • The combination of optical fiber and honeycomb significantly enhanced the performance of VOCs photodegradation. • The removal efficiency of m-xylene is enhanced to 96.5% as compared to 22.0% for UV irradiation alone. • Fiber-illuminated honeycomb reactor is the first step toward an industrial-scale technology on the removal of xylene. -- Abstract: The removal of volatile organic compounds (VOCs) at ppb level is one of the most critical challenges in clean rooms for the semiconductor industry. Photocatalytic oxidation is an innovative and promising technology for ppb-level VOCs degradation. We have designed a fiber-illuminated honeycomb reactor (FIHR) in which the removal efficiency of m-xylene is significantly enhanced to 96.5% as compared to 22.0% for UV irradiation only. The results indicate that photocatalysts not only play the role to substantially oxidize m-xylene, but also alter the chemical properties of xylene under UV illumination. Using the FIHR with Mn-TiO 2 photocatalyst not only increased the m-xylene removal efficiency, but also increased the CO 2 selectivity. Interestingly, Mn-TiO 2 in FIHR also showed a very good reusability, 93% removal efficiency was still achieved in 72-h in reaction. Thus, the FIHR gave very high removal efficiency for xylene at ppb level under room temperature. The FIHR has great potential application in the clean room for the air purification system in the future

Enhanced xylene removal by photocatalytic oxidation using fiber-illuminated honeycomb reactor at ppb level

Energy Technology Data Exchange (ETDEWEB)

Wu, Yi-Ting [Department of Chemical Engineering, National Taiwan University, Taipei 10617, Taiwan (China); Yu, Yi-Hui [Department of Civil Engineering, National Taiwan University, Taipei 106, Taiwan (China); Nguyen, Van-Huy [Department of Chemical Engineering, National Taiwan University of Science and Technology, Taipei 10617, Taiwan (China); Lu, Kung-Te [Department of Chemical Engineering, National Taiwan University, Taipei 10617, Taiwan (China); Wu, Jeffrey Chi-Sheng, E-mail: cswu@ntu.edu.tw [Department of Chemical Engineering, National Taiwan University, Taipei 10617, Taiwan (China); Chang, Luh-Maan [Department of Civil Engineering, National Taiwan University, Taipei 106, Taiwan (China); Kuo, Chi-Wen [Taiwan Semiconductor Manufacturing Company, Hsinchu 30078, Taiwan (China)

2013-11-15

Graphical abstract: We have designed a fiber-illuminated honeycomb reactor (FIHR) in which the removal efficiency of m-xylene is significantly enhanced to 96.5% as compared to 22.0% for UV irradiation only. The results indicate that photocatalysts not only play the role to substantially oxidize m-xylene, but also alter the chemical properties of xylene under UV illumination. -- Highlights: • The combination of optical fiber and honeycomb significantly enhanced the performance of VOCs photodegradation. • The removal efficiency of m-xylene is enhanced to 96.5% as compared to 22.0% for UV irradiation alone. • Fiber-illuminated honeycomb reactor is the first step toward an industrial-scale technology on the removal of xylene. -- Abstract: The removal of volatile organic compounds (VOCs) at ppb level is one of the most critical challenges in clean rooms for the semiconductor industry. Photocatalytic oxidation is an innovative and promising technology for ppb-level VOCs degradation. We have designed a fiber-illuminated honeycomb reactor (FIHR) in which the removal efficiency of m-xylene is significantly enhanced to 96.5% as compared to 22.0% for UV irradiation only. The results indicate that photocatalysts not only play the role to substantially oxidize m-xylene, but also alter the chemical properties of xylene under UV illumination. Using the FIHR with Mn-TiO{sub 2} photocatalyst not only increased the m-xylene removal efficiency, but also increased the CO{sub 2} selectivity. Interestingly, Mn-TiO{sub 2} in FIHR also showed a very good reusability, 93% removal efficiency was still achieved in 72-h in reaction. Thus, the FIHR gave very high removal efficiency for xylene at ppb level under room temperature. The FIHR has great potential application in the clean room for the air purification system in the future.

Fabrication of Biomembrane from Banana Stem for Lead Removal

Directory of Open Access Journals (Sweden)

Afianti Sulastri

2016-04-01

Full Text Available Heavy metal (i.e. lead (Pb is one of the environmental issues recently due to its danger for human health. Therefore, strategy for removing Pb from waste water treatment is important. One of the prospective methods to remove Pb is membrane biofilter. Here, the purpose of this study was to prepare the membrane biofilter for Pb removal process. In this study, membrane biofilter was produced from banana stem. Banana stem was selected because of its abundant availability   in Indonesia. And, for somewhat, this banana stem can be environmental problems (become waste since Indonesia is one of the top producers in the world. In short of the experimental procedure, we conducted three steps of experiments: (1 Preparation of microbial cellulose using Acetobacter xylinum using banana stem for a main source; (2 Synthesis of cellulose acetate; and (3 Preparation of biomembrane from obtained cellulose acetate. To produce membrane biofilter, the cellulose acetate was dissolved into dichloromethane to form a dope solution. Then, the doped solution was printed in Petri dish. Some biomembrane properties were characterized for identification, i.e. infrared spectra, electron microscope, and elemental analysis. Experimental results showed that we succeeded to prepare biomembrane with a pore size of 5 μm. The filtration efficiency of our prepared membrane was 93.7% of Pb when using Pb with a concentration of 10 ppm.

Thermal-hydraulic analysis of an innovative decay heat removal system for lead-cooled fast reactors

International Nuclear Information System (INIS)

Giannetti, Fabio; Vitale Di Maio, Damiano; Naviglio, Antonio; Caruso, Gianfranco

2016-01-01

Highlights: • LOOP thermal-hydraulic transient analysis for lead-cooled fast reactors. • Passive decay heat removal system concept to avoid lead freezing. • Solution developed for the diversification of the decay heat removal functions. • RELAP5 vs. RELAP5-3D comparison for lead applications. - Abstract: Improvement of safety requirements in GEN IV reactors needs more reliable safety systems, among which the decay heat removal system (DHR) is one of the most important. Complying with the diversification criteria and based on pure passive and very reliable components, an additional DHR for the ALFRED reactor (Advanced Lead Fast Reactor European Demonstrator) has been proposed and its thermal-hydraulic performances are analyzed. It consists in a coupling of two innovative subsystems: the radiative-based direct heat exchanger (DHX), and the pool heat exchanger (PHX). Preliminary thermal-hydraulic analyses, by using RELAP5 and RELAP5-3D© computer programs, have been carried out showing that the whole system can safely operate, in natural circulation, for a long term. Sensitivity analyses for: the emissivity of the DHX surfaces, the PHX water heat transfer coefficient (HTC) and the lead HTC have been carried out. In addition, the effects of the density variation uncertainty on the results has been analyzed and compared. It allowed to assess the feasibility of the system and to evaluate the acceptable range of the studied parameters. A comparison of the results obtained with RELAP5 and RELAP5-3D© has been carried out and the analysis of the differences of the two codes for lead is presented. The features of the innovative DHR allow to match the decay heat removal performance with the trend of the reactor decay heat power after shutdown, minimizing at the same time the risk of lead freezing. This system, proposed for the diversification of the DHR in the LFRs, could be applicable in the other pool-type liquid metal fast reactors.

Thermal-hydraulic analysis of an innovative decay heat removal system for lead-cooled fast reactors

Energy Technology Data Exchange (ETDEWEB)

Giannetti, Fabio; Vitale Di Maio, Damiano; Naviglio, Antonio; Caruso, Gianfranco, E-mail: gianfranco.caruso@uniroma1.it

2016-08-15

Highlights: • LOOP thermal-hydraulic transient analysis for lead-cooled fast reactors. • Passive decay heat removal system concept to avoid lead freezing. • Solution developed for the diversification of the decay heat removal functions. • RELAP5 vs. RELAP5-3D comparison for lead applications. - Abstract: Improvement of safety requirements in GEN IV reactors needs more reliable safety systems, among which the decay heat removal system (DHR) is one of the most important. Complying with the diversification criteria and based on pure passive and very reliable components, an additional DHR for the ALFRED reactor (Advanced Lead Fast Reactor European Demonstrator) has been proposed and its thermal-hydraulic performances are analyzed. It consists in a coupling of two innovative subsystems: the radiative-based direct heat exchanger (DHX), and the pool heat exchanger (PHX). Preliminary thermal-hydraulic analyses, by using RELAP5 and RELAP5-3D© computer programs, have been carried out showing that the whole system can safely operate, in natural circulation, for a long term. Sensitivity analyses for: the emissivity of the DHX surfaces, the PHX water heat transfer coefficient (HTC) and the lead HTC have been carried out. In addition, the effects of the density variation uncertainty on the results has been analyzed and compared. It allowed to assess the feasibility of the system and to evaluate the acceptable range of the studied parameters. A comparison of the results obtained with RELAP5 and RELAP5-3D© has been carried out and the analysis of the differences of the two codes for lead is presented. The features of the innovative DHR allow to match the decay heat removal performance with the trend of the reactor decay heat power after shutdown, minimizing at the same time the risk of lead freezing. This system, proposed for the diversification of the DHR in the LFRs, could be applicable in the other pool-type liquid metal fast reactors.

Predicting Bacteria Removal by Enhanced Stormwater Control Measures (SCMs) at the Watershed Scale

Science.gov (United States)

Wolfand, J.; Bell, C. D.; Boehm, A. B.; Hogue, T. S.; Luthy, R. G.

2017-12-01

Urban stormwater is a major cause of water quality impairment, resulting in surface waters that fail to meet water quality standards and support their designated uses. Fecal indicator bacteria are present in high concentrations in stormwater and are strictly regulated in receiving waters; yet, their fate and transport in urban stormwater is poorly understood. Stormwater control measures (SCMs) are often used to treat, infiltrate, and release urban runoff, but field measurements show that the removal of bacteria by these structural solutions is limited (median log removal = 0.24, n = 370). Researchers have therefore looked to improve bacterial removal by enhancing SCMs through alterations in flow regimes or adding geomedia such as biochar. The present research seeks to develop a model to predict removal of fecal indicator bacteria by enhanced SCMs at the watershed scale in a semi-arid climate. Using the highly developed Ballona Creek watershed (290 km2) located in Los Angeles County as a case study, a hydrologic model is coupled with a stochastic water quality model to predict E. coli concentration near the outfall of the Ballona Creek, Santa Monica Bay. A hydrologic model was developed using EPA SWMM, calibrated for flow from water year 1998-2006 (NSE = 0.94; R2 = 0.94), and validated from water year 2007-2015 (NSE = 0.90; R2 = 0.93). This bacterial loading model was then linked to EPA SUSTAIN and a SCM bacterial removal script to simulate log removal of bacteria by various SCMs and predict bacterial concentrations in Ballona Creek. Preliminary results suggest small enhancements to SCMs that improve bacterial removal (<0.5 log removal) may offer large benefits to surface water quality and enable communities such as Los Angeles to meet their regulatory requirements.

Enhanced nitrogen removal in trickling filter plants.

Science.gov (United States)

Dai, Y; Constantinou, A; Griffiths, P

2013-01-01

The Beaudesert Sewage Treatment Plant (STP), originally built in 1966 and augmented in 1977, is a typical biological trickling filter (TF) STP comprising primary sedimentation tanks (PSTs), TFs and humus tanks. The plant, despite not originally being designed for nitrogen removal, has been consistently achieving over 60% total nitrogen reduction and low effluent ammonium concentration of less than 5 mg NH3-N/L. Through the return of a NO3(-)-rich stream from the humus tanks to the PSTs and maintaining an adequate sludge age within the PSTs, the current plant is achieving a substantial degree of denitrification. Further enhanced denitrification has been achieved by raising the recycle flows and maintaining an adequate solids retention time (SRT) within the PSTs. This paper describes the approach to operating a TF plant to achieve a high degree of nitrification and denitrification. The effectiveness of this approach is demonstrated through the pilot plant trial. The results from the pilot trial demonstrate a significant improvement in nitrogen removal performance whilst maximising the asset life of the existing infrastructure. This shows great potential as a retrofit option for small and rural communities with pre-existing TFs that require improvements in terms of nitrogen removal.

Study on complexed lead and cadmium ions removal from aqueous solutions by means of ion exchange method

International Nuclear Information System (INIS)

Dudzinska, M.

1992-01-01

The possibility of simultaneous removal of heavy metal ions and organic chelates from waste water has been studied. The experimental work has been preceded by extensive theoretical considerations and calculations of physico-chemical parameters of the process for model and real waste water systems. The negative influence of the presence of sulfate anions on cadmium and lead complexes removal in ion exchange process has been experimentally proved. In the systems free of sulfate anions or when their concentrations were low, the purification process conducted on Amberlite IRA-68 was very effective for cadmium and lead complexes removal. 112 refs, 78 figs, 15 tabs

Technology Demonstration of Wet Abrasive Blasting for Removal of Lead- and Asbestos-Containing Paint

National Research Council Canada - National Science Library

Race, Timothy

2003-01-01

...). This technology demonstration showed that wet blasting using an engineered abrasive can safely and effectively remove lead- and asbestos-containing paint from exterior concrete masonry unit walls...

Biostimulation strategies to enhance manganese removal in drinking water biofilters

DEFF Research Database (Denmark)

Breda, Inês Lousinha Ribeiro; Ramsay, Loren; Søborg, Ditte

to national drinking water criteria. The period during which virgin filter media matures into a fully functional biofilter is designated as the start-up period. The duration of a start-up for efficient manganese removal varies from weeks to more than a year. The aim of this study was to investigate...... growth and activity of specific bacteria. Biostimulation of virgin media to enhance initial manganese removal using different amendments strategies is possible especially in the early stages of filter development whereas autocatalytic processes appear to become dominant with time. The complex...

Fruit stones from industrial waste for the removal of lead ions from polluted water.

Science.gov (United States)

Rashed, M N

2006-08-01

Lead, one of the earliest metals recognized and used by humans, has a long history of beneficial use. However, it is now recognized as toxic and as posing a widespread threat to humans and wildlife. Treatment of lead from polluted water and wastewater has received a great deal of attention. Adsorption is one of the most common technologies for the treatment of lead-polluted water. This technique was evaluated here, with the goal of identifying innovative, low-cost adsorbent. This study presents experiments undertaken to determine the suitable conditions for the use of peach and apricot stones, produced from food industries as solid waste, as adsorbents for the removal of lead from aqueous solution. Chemical stability of adsorbents, effect of pH, adsorbents dose, adsorption time and equilibrium concentration were studied. The results reveal that adsorption of lead ions onto peach stone was stronger than onto apricot stone up to 3.36% at 3 h adsorption time. Suitable equilibrium time for the adsorption was 3-5 h (% Pb adsorption 93% for apricot and 97.64% for peach). The effective adsorption range for pH in the range was 7-8. Application of Langmuir and Freundlich isotherm models show high adsorption maximum and binding energies for using these adsorbents for the removal of lead ions from contaminated water and wastewater.

Supported liquid membrane based removal of lead(II) and cadmium(II) from mixed feed: Conversion to solid waste by precipitation

Energy Technology Data Exchange (ETDEWEB)

Bhatluri, Kamal Kumar; Manna, Mriganka Sekhar; Ghoshal, Aloke Kumar; Saha, Prabirkumar, E-mail: p.saha@iitg.ac.in

2015-12-15

Highlights: • Simultaneous removal of two heavy metals lead and cadmium. • Conversion of liquid waste to solid precipitation. • Precipitation facilitates the metals transportation through LM. • Solidification of liquid waste minimizes the final removal of waste. - Abstract: Simultaneous removal of two heavy metals, lead(II) and cadmium(II), from mixed feed using supported liquid membrane (SLM) based technique is investigated in this work. The carrier-solvent combination of “sodium salt of Di-2-ethylhexylphosphoric acid (D2EHPA) (4% w/w) in environmentally benign coconut oil” was immobilized into the pores of solid polymeric polyvinylidene fluoride (PVDF) support. Sodium carbonate (Na{sub 2}CO{sub 3}) was used as the stripping agent. Carbonate salts of lead(II) and cadmium(II) were formed in the stripping side interface and they were insoluble in water leading to precipitation inside the stripping solution. The transportation of solute is positively affected due to the precipitation. Lead(II) removal was found to be preferential due to its favorable electronic configuration. The conversion of the liquid waste to the solid one was added advantage for the final removal of hazardous heavy metals.

Significantly improving trace thallium removal from surface waters during coagulation enhanced by nanosized manganese dioxide.

Science.gov (United States)

Huangfu, Xiaoliu; Ma, Chengxue; Ma, Jun; He, Qiang; Yang, Chun; Jiang, Jin; Wang, Yaan; Wu, Zhengsong

2017-02-01

Thallium (Tl) is an element of high toxicity and significant accumulation in human body. There is an urgent need for the development of appropriate strategies for trace Tl removal in drinking water treatment plants. In this study, the efficiency and mechanism of trace Tl (0.5 μg/L) removal by conventional coagulation enhanced by nanosized manganese dioxide (nMnO 2 ) were explored in simulated water and two representative surface waters (a river water and a reservoir water obtained from Northeast China). Experimental results showed that nMnO 2 significantly improve Tl(I) removal from selected waters. The removal efficiency was dramatically higher in the simulated water, demonstrating by less than 0.1 μg/L Tl residual. The enhancement of trace Tl removal in the surface waters decreased to a certain extent. Both adjusting water pH to alkaline condition and preoxidation of Tl(I) to Tl(III) benefit trace Tl removal from surface waters. Data also indicated that competitive cation of Ca 2+ decreased the efficiency of trace Tl removal, resulting from the reduction of Tl adsorption on nMnO 2 . Humic acid could largely low Tl removal efficiency during nMnO 2 enhanced coagulation processes. Trace elemental Tl firstly adsorbed on nMnO 2 and then removed accompanying with nMnO 2 settling. The information obtained in the present study may provide a potential strategy for drinking water treatment plants threatened by trace Tl. Copyright © 2016 Elsevier Ltd. All rights reserved.

Enhanced removal of radioactive particles by fluorocarbon surfactant solutions

International Nuclear Information System (INIS)

Kaiser, R.; Harling, O.K.

1993-08-01

The proposed research addressed the application of ESI's particle removal process to the non-destructive decontamination of nuclear equipment. The cleaning medium used in this process is a solution of a high molecular weight fluorocarbon surfactant in an inert perfluorinated liquid which results in enhanced particle removal. The perfluorinated liquids of interest, which are recycled in the process, are nontoxic, nonflammable, and environmentally compatible, and do not present a hazard to the ozone layer. The information obtained in the Phase 1 program indicated that the proposed ESI process is technically effective and economically attractive. The fluorocarbon surfactant solutions used as working media in the ESI process survived exposure of up to 10 Mrad doses of gamma rays, and are considered sufficiently radiation resistant for the proposed process. Ultrasonic cleaning in perfluorinated surfactant solutions was found to be an effective method of removing radioactive iron (Fe 59) oxide particles from contaminated test pieces. Radioactive particles suspended in the process liquids could be quantitatively removed by filtration through a 0.1 um membrane filter. Projected economics indicate a pre-tax pay back time of 1 month for a commercial scale system

Poly(acrylic acid) modifying bentonite with in-situ polymerization for removing lead ions.

Science.gov (United States)

He, Y F; Zhang, L; Yan, D Z; Liu, S L; Wang, H; Li, H R; Wang, R M

2012-01-01

In this paper, a new kind of poly(acrylic acid) modified clay adsorbent, the poly(acrylic acid)/bentonite composite (PAA/HB) was prepared by in-situ polymerization, and utilized to remove lead(II) ions from solutions. The maximum adsorption of adsorbent is at pH 5 for metal ions, whereas the adsorption starts at pH 2. The effects of contact time (5-60 min), initial concentration of metal ions (200-1,000 mg/L) and adsorbent dosage (0.04-0.12 g/100 mL) have been reported in this article. The experimental data were investigated by means of kinetic and equilibrium adsorption isotherms. The kinetic data were analyzed by the pseudo-first-order and pseudo-second-order equation. The experimental data fitted the pseudo-second-order kinetic model very well. Langmuir and Freundlich isotherms were tried for the system to better understand the adsorption isotherm process. The maximal adsorption capacity of the lead(II) ions on the PAA/HB, as calculated from the Langmuir model, was 769.2 mg/g. The results in this study indicated that PAA/HB was an attractive candidate for removing lead(II) (99%).

Improved removal performance and mechanism investigation of papermaking wastewater treatment using manganese enhanced Fenton reaction.

Science.gov (United States)

Wang, Yingcai; Wang, Can; Shi, Shuai; Fang, Shuai

2018-06-01

The effects of Mn(II) on Fenton system to treat papermaking wastewater and the mechanism of Mn(II) enhanced Fenton reaction were investigated in this study. The chemical oxygen demand (COD) removal efficiency was enhanced in the presence of Mn(II), which increased by 19% compared with that of the Fenton system alone. The pseudo-first order reaction kinetic rate constant of Mn(II)/Fenton system was 2.11 times higher than that of Fenton system. 67%-81% COD were removed with the increasing Mn(II) concentration from 0 to 0.8 g/L. COD removal efficiency was also enhanced in a wider pH range (3-7), which indicated the operation parameters of Fenton technology could be broadened to a milder condition. The study of the mechanism showed that Mn(II) participated in the oxidation and coagulation stages in Fenton system. In the oxidation stage, Mn(II) promotes the production of HO 2 •/ O 2 • - , then HO 2 •/ O 2 • - reacts with Fe(III) to accelerate the formation of Fe(II), and finally accelerates the production of HO•. Meantime MnMnO 3 and Fe(OH) 3 forms in the coagulation stage, facilitating the removal of suspended substances and a large amount of COD, which enhances the overall COD removal of papermaking wastewater. This study provided a detailed mechanism to improve practical applications of Fenton technology.

Active removal of ibuprofen by Money plant enhanced by ferrous ions.

Science.gov (United States)

Chehrenegar, Behdad; Hu, Jiangyong; Ong, Say Leong

2016-02-01

In this study, the removal of ibuprofen (IBP), a pharmaceutical compound, from aqueous media by Money plant (Epipremnum aureum) was investigated. The effect of ferrous iron (Fe(2+)) on enhancing the IBP removal rate was also analyzed. The first-order removal rate constants showed higher values for lower IBP initial concentrations in the range of 0.20-0.28 d(-1) for an initial concentration of 125 μg L(-1) to 0.03-0.13 d(-1) for an initial concentration of 1000 μg L(-1). Introducing ferrous iron to the aqueous media enhanced the first-order removal rate constant up to 6.5 times in a 3 d time period. Along with the removal of IBP from the media, the endogenous concentration of H2O2 also decreased presumably by the production of hydroxyl radical (·OH). Reduction in the endogenous H2O2 concentration was recorded to be 38% and 98% in the absence and presence of Fe(2+) respectively in the first day and the H2O2 level remained considerably low until day 7 which then gradually increased slightly. Simultaneous reduction of IBP and endogenous H2O2 concentration could be due to the reaction of IBP with ·OH and presumably ·OH production itself accelerated via Fenton reaction. In addition, presence of sodium bicarbonate (NaHCO3) as ·OH scavenger in the system showed reduction of first-order removal rate constant from 1.30 d(-1) to 0.07 d(-1) which could be a possible evidence of biological advanced oxidation process which is believed to play an important role in phytoremediation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Simultaneous nitrogen and phosphorus removal in the sulfur cycle-associated Enhanced Biological Phosphorus Removal (EBPR) process.

Science.gov (United States)

Wu, Di; Ekama, George A; Wang, Hai-Guang; Wei, Li; Lu, Hui; Chui, Ho-Kwong; Liu, Wen-Tso; Brdjanovic, Damir; van Loosdrecht, Mark C M; Chen, Guang-Hao

2014-02-01

Hong Kong has practiced seawater toilet flushing since 1958, saving 750,000 m(3) of freshwater every day. A high sulfate-to-COD ratio (>1.25 mg SO4(2-)/mg COD) in the saline sewage resulting from this practice has enabled us to develop the Sulfate reduction, Autotrophic denitrification and Nitrification Integrated (SANI(®)) process with minimal sludge production and oxygen demand. Recently, the SANI(®) process has been expanded to include Enhanced Biological Phosphorus Removal (EBPR) in an alternating anaerobic/limited-oxygen (LOS-EBPR) aerobic sequencing batch reactor (SBR). This paper presents further development - an anaerobic/anoxic denitrifying sulfur cycle-associated EBPR, named as DS-EBPR, bioprocess in an alternating anaerobic/anoxic SBR for simultaneous removal of organics, nitrogen and phosphorus. The 211 day SBR operation confirmed the sulfur cycle-associated biological phosphorus uptake utilizing nitrate as electron acceptor. This new bioprocess cannot only reduce operation time but also enhance volumetric loading of SBR compared with the LOS-EBPR. The DS-EBPR process performed well at high temperatures of 30 °C and a high salinity of 20% seawater. A synergistic relationship may exist between sulfur cycle and biological phosphorus removal as the optimal ratio of P-release to SO4(2-)-reduction is close to 1.0 mg P/mg S. There were no conventional PAOs in the sludge. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evaluation of natural clay Brasgel as adsorbent in removal of lead in synthetic waste water

International Nuclear Information System (INIS)

Lima, W.S.; Rodrigues, M.G.F.; Mota, M.F.; Patricio, A.C.L.; Silva, M.M.

2012-01-01

The smectite clays have high adsorption capacity and cation exchange. Due to its chemical and physical characteristics, they can be effectively used as adsorbent of pollutants (such as metal ions). The initial objective of this study was to characterize the clay Brasgel through the techniques of X-Ray Diffraction (XRD), X-Ray Spectrometry by Energy Dispersive (EDX) and nitrogen adsorption (BET method), seeking its use in removing lead (Pb 2+ ) from synthetic effluents. System was used in finite bath to assess the potential removal of lead (Pb 2+ ), following a 2 2 factorial experimental design with three center point experiments, taking as input variables: pH and initial concentrations of lead (Pb 2+ ). The clay has Brasgel clay in its composition that characterize it as a smectite clay. By having a large surface area, this clay showed great potential on the adsorption of metal ions. (author)

Simultaneous removal of humic acid/fulvic acid and lead from landfill leachate using magnetic graphene oxide

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jing [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Gong, Ji-Lai, E-mail: jilaigong@gmail.com [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Zenga, Guang-Ming, E-mail: zgming@hnu.edu.cn [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Ou, Xiao-Ming [China National Engineering Research Center for Agrochemicals, Hunan Research Institute of Chemical Industry, Changsha 410014 (China); Jiang, Yan; Chang, Ying-Na; Guo, Min; Zhang, Chang; Liu, Hong-Yu [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China)

2016-05-01

Highlights: • Magnetic graphene oxide was synthesized and used to simultaneously remove HA/FA and Pb(II) from landfill leachate. • In HA-Pb(II) system, Pb(II) removal rapidly increased to the maximum (about 87%) and considerably decreased with increasing HA concentration. However, in FA-Pb(II) system, Pb(II) removal slightly increased and remained constant as FA concentration increased. • In binary system, the removal efficiency of HA/FA by MGO was enhanced due to the increase of Pb(II) concentration. • In landfill leachate, MGO showed considerable removal efficiency for both Pb(II) and HA/FA. - Abstract: The elimination of organic matters and heavy metals in landfill leachate remains a longstanding challenge in wastewater treatment. In this study, magnetic graphene oxide (MGO) was synthesized and investigated to explore the possibility of applying in the simultaneous removal of HA/FA and Pb(II) from landfill leachate. MGO was characterized by Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) spectroscope. In single system, the sorption isotherm for FA on MGO at 25 °C were better described by Freundlich model than Langmuir and Temkin models with a maximum adsorption capacity of 72.38 mg/g. The isotherm data for HA at 25 °C was fitted well both Freundlich and Temkin models with a maximum adsorption capacity of 98.82 mg/g, while the isotherm data for Pb(II) at 25 °C was fitted well both Langmuir and Temkin models with a maximum adsorption capacity of 58.43 mg/g. In binary system, results showed that TOC removal (both in HA and FA) enhanced with increasing Pb(II). Furthermore, TOC removal enhancement caused by the increase of Pb(II) in HA-Pb(II) system was greater than that in FA-Pb(II), which was caused by HA possessing more substantial aromatic rings than FA. Noticeably, Pb(II) removal steeply increased to the maximum (about 87%) with increasing

Laboratory studies on the removal of radon-born lead from KamLAND's organic liquid scintillator

Science.gov (United States)

Keefer, G.; Grant, C.; Piepke, A.; Ebihara, T.; Ikeda, H.; Kishimoto, Y.; Kibe, Y.; Koseki, Y.; Ogawa, M.; Shirai, J.; Takeuchi, S.; Mauger, C.; Zhang, C.; Schweitzer, G.; Berger, B. E.; Dazeley, S.; Decowski, M. P.; Detwiler, J. A.; Djurcic, Z.; Dwyer, D. A.; Efremenko, Y.; Enomoto, S.; Freedman, S. J.; Fujikawa, B. K.; Furuno, K.; Gando, A.; Gando, Y.; Gratta, G.; Hatakeyama, S.; Heeger, K. M.; Hsu, L.; Ichimura, K.; Inoue, K.; Iwamoto, T.; Kamyshkov, Y.; Karwowski, H. J.; Koga, M.; Kozlov, A.; Lane, C. E.; Learned, J. G.; Maricic, J.; Markoff, D. M.; Matsuno, S.; McKee, D.; McKeown, R. D.; Miletic, T.; Mitsui, T.; Motoki, M.; Nakajima, Kyo; Nakajima, Kyohei; Nakamura, K.; O`Donnell, T.; Ogawa, H.; Piquemal, F.; Ricol, J.-S.; Shimizu, I.; Suekane, F.; Suzuki, A.; Svoboda, R.; Tajima, O.; Takemoto, Y.; Tamae, K.; Tolich, K.; Tornow, W.; Watanabe, Hideki; Watanabe, Hiroko; Winslow, L. A.; Yoshida, S.

2015-01-01

The removal of radioactivity from liquid scintillator has been studied in preparation of a low background phase of KamLAND. This paper describes the methods and techniques developed to measure and efficiently extract radon decay products from liquid scintillator. We report the radio-isotope reduction factors obtained when applying various extraction methods. During this study, distillation was identified as the most efficient method for removing radon-born lead from liquid scintillator.

Non-tumor enhancement at the surgical margin on CT after the removal of brain tumors

International Nuclear Information System (INIS)

Adachi, Michito; Hosoya, Takaaki; Yamaguchi, Kohichi; Yamada, Kiyotada

1992-01-01

Marginal enhancement is occasionally seen at the surgical margin on CT after the total removal of brain tumors. This enhancement disappears in due time, and therefore we call it non-tumor enhancement. It is often difficult, however, to differentiate non-tumor enhancement from tumor recurrence. In this study, we attempted to determine the characteristics of non-tumor enhancement. The subjects of the study consisted of 15 patients with astrocytoma and one with metastatic tumor in whom sequential CT scans had been performed after total removal of the tumor. Based on the observation of these sequential CT scans, the characteristics of non-tumor enhancement were presumed to be as follows: (1) In four cases, enhancement at the surgical margin persisted more than four months after surgery and then disappeared. Therefore, these cases were considered non-tumor enhancement. Prolonged duration of enhancement such as that in these cases is not necessarily due to recurrence. Marginal enhancement within 3 mm in thickness and with a well-demarcated border like that of a flax is likely to be non-tumor enhancement. (author)

Temporal dependence of the enhancement of material removal in femtosecond-nanosecond dual-pulse laser-induced breakdown spectroscopy

International Nuclear Information System (INIS)

Scaffidi, Jon; Pearman, William; Carter, J. Chance; Colston, Bill W. Jr.; Angel, S. Michael

2004-01-01

Despite the large neutral atomic and ionic emission enhancements that have been noted in collinear and orthogonal dual-pulse laser-induced breakdown spectroscopy, the source or sources of these significant signal and signal-to-noise ratio improvements have yet to be explained. In the research reported herein, the combination of a femtosecond preablative air spark and a nanosecond ablative pulse yields eightfold and tenfold material removal improvement for brass and aluminum, respectively, but neutral atomic emission is enhanced by only a factor of 3-4. Additionally, temporal correlation between enhancement of material removal and of atomic emission is quite poor, suggesting that the atomic-emission enhancements noted in the femtosecond-nanosecond pulse configuration result in large part from some source other than simple improvement in material removal

Lead and copper removal from aqueous solutions by porous glass derived calcium hydroxyapatite

International Nuclear Information System (INIS)

Liang Wen; Zhan Lei; Piao Longhua; Ruessel, Christian

2011-01-01

Graphical abstract: . Adsorption of Pb 2+ increases with the increase in NaCl volume percentage (1:0%, 2:30%, 3:40%, 4:40%) of the Glass Derived Hydroxyapatite and reaches equilibrium after 24 h. Highlights: → Novel porous glass derived hydroxyapatite matrix is prepared. → Glass derived hydroxyapatite matrix adsorbs lead and copper ions in solutions effectively. → Two adsorption mechanisms including ion exchange theory and the dissolution and precipitation theory are involved in removal of the heavy metal ions from the solutions. - Abstract: A porous glass was prepared by sintering Na 2 O-CaO-B 2 O 3 glass powder with powdered sodium chloride. Subsequently, the sodium chloride was dissolved in water resulting in a highly porous material. A sample was prepared consisting of 60 vol% glass and 40 vol% salt which both had particle sizes 2 HPO 4 solutions at room temperature for 1 day. The porous glass derived hydroxyapatite matrix was then processed for removing lead and copper ions from aqueous solutions. The results showed that the glass derived calcium hydroxyapatite matrix effectively immobilizes lead and copper ions in solution. The adsorption mechanism was investigated by the X-ray Diffraction (XRD) and Scanning Electron Microscopy including Energy Dispersive X-Ray Spectrometry (SEM-EDX).

Microbial Community Profile of a Lead Service Line Removed from a Drinking Water Distribution System▿

Science.gov (United States)

White, Colin; Tancos, Matthew; Lytle, Darren A.

2011-01-01

A corroded lead service line was removed from a drinking water distribution system, and the microbial community was profiled using 16S rRNA gene techniques. This is the first report of the characterization of a biofilm on the surface of a corroded lead drinking water service line. The majority of phylotypes have been linked to heavy-metal-contaminated environments. PMID:21652741

A Novel GH-92 Nano-Adsorbent Using the Sponge from the Persian Gulf for Lead and Cadmium Removal

Directory of Open Access Journals (Sweden)

Hossein Ghafourian

2015-05-01

Full Text Available Removing pollutants from aquatic ecosystems, especially from drinking water, has always been a major concern for scientists. Recent decades have witnessed the widespread application of natural compounds used as adsorbents to remove various pollutants. On the other hand, studies have proved nanotechnology to be an effective way of removing pollutants. A new type of sponge belonging to the family Demospongiae that has nano holes and is native to the Persian Gulf was investigated for the first time in the present study for use as an adsorbent to remove calcium, magnesium, cobalt, cadmium, and lead ions from water. For this purpose, adbsorption in sponges of different aggregate sizes, contact time, particle size, and ambient pH were measured. The results showed that the proposed sponge is capable of adsorbing the above-mentioned metal ions to various degrees. While small amounts of calcium, magnesium, and cobalt were adsorbed by this sponge, cadmium recorded a higher adsorption of 2.37 mg/g at pH=5. The highest adsorption level of 79.19 mg per gram of adsorbent was recorded for lead at a pH range of 4.5-5 with a mesh size of 230. This is the highest adsorption ever recorded for lead in the literature on selective separation of lead from the other ions.

Evaluation of the potentiality of a Mexican natural zeolite chabazite-type in the lead removal in water

International Nuclear Information System (INIS)

Alvarado I, J.; Sotelo L, M.; Meza F, D.; Paz M, F. A.; Maubert F, M.

2013-01-01

The intention of this paper is to present the characterization of a natural zeolite, chabazite-type, from the Mexican reservoir La Palma, at Divisaderos, Sonora, where their potential use as ion exchange material to remove lead in water is assessed. The chabazite was characterized through X-ray diffraction, Icp-OES, Icp-Ms, EDX, Bet and TG/TGD. The results indicate the presence of Ba(1930 ppm) and Sr(1220 ppm), which are characteristic of aluminium rich phases. A chabazite modification treatment is proposed by using solutions of NaOH (0.1 M) and NH 4 NO 3 (1 M). The lead removal kinetics both in natural zeolite as in their chemically modified forms was obtained by using the ion exchange process in a batch reactor. The results show how unnecessary natural zeolite homo ionization is for the removal of lead, thereby obtaining the equilibrium concentration of unmodified zeolite for plotting the adsorption isotherm, which was adjusted to Langmuir model. The Langmuir isotherm has a good fit of the results at equilibrium (R 2 =0.92), which demonstrates that natural zeolites studied, in its natural form, contains exchangeable cations required (Ca +2 , Mg 2+ and Na + ) for potentially be used as an adsorbent material/ion exchanger for water treatment impacted by lead. (Author)

Citric-acid preacidification enhanced electrokinetic remediation for removal of chromium from chromium-residue-contaminated soil.

Science.gov (United States)

Meng, Fansheng; Xue, Hao; Wang, Yeyao; Zheng, Binghui; Wang, Juling

2018-02-01

Electrokinetic experiments were conducted on chromium-residue-contaminated soils collected from a chemical plant in China. Acidification-electrokinetic remediation technology was proposed in order to solve the problem of removing inefficient with ordinary electrokinetic. The results showed that electrokinetic remediation removal efficiency of chromium from chromium-contaminated soil was significantly enhanced with acidizing pretreatment. The total chromium [Cr(T)] and hexavalent chromium [Cr(VI)] removal rate of the group acidized by citric acid (0.9 mol/L) for 5 days was increased from 6.23% and 19.01% in the acid-free experiments to 26.97% and 77.66% in the acidification-treated experiments, respectively. In addition, part of chromium with the state of carbonate-combined will be converted into water-soluble state through acidification to improve the removal efficiency. Within the appropriate concentration range, the higher concentration of acid was, the more chromium was released. So the removal efficiency of chromium depended on the acid concentration. The citric acid is also a kind of complexing agent, which produced complexation with Cr that was released by the electrokinetic treatment and then enhanced the removal efficiency. The major speciation of chromium that was removed from soils by acidification-electrokinetics remediation was acid-soluble speciation, revivification speciation and oxidation speciation, which reduced biological availability of chromium.

Enhanced adsorbability and photocatalytic activity of TiO2-graphene composite for polycyclic aromatic hydrocarbons removal in aqueous phase.

Science.gov (United States)

Bai, Hongzhen; Zhou, Jun; Zhang, Hongjian; Tang, Guping

2017-02-01

Photodegradation via titanium dioxide (TiO 2 ) has been used to remove polycyclic aromatic hydrocarbons (PAHs) from environmental media broadly. In this study, a series of TiO 2 -graphene composites (P25-GR) with different GR weight ratios were synthesized via hydrothermal reaction of graphene oxide (GO) and P25. Their structures were characterized and the proprieties were tested in aqueous phase. Phenanthrene (PHE), fluoranthene (FLAN), and benzo[a]pyrene (BaP) were selected as models of PAHs. The experiment indicated that P25-2.5%GR exhibited enhancement in both adsorption and photodegradation, ∼80% of PAHs were removed after 2h photocatalysis. The influence of photodegradation rate was studied, including PAHs initial concentration and pH. Aromatic intermediates were identified during the reaction process and the degradation pathways were portrayed. This work explored the enhanced photocatalysis performance was attributed to the PAH-selective adsorbability and the strong electron transfer ability of the composite. The analysis of the degradation intermediates confirmed that the reaction proceeded with the formation of free radicals, leading to the gradual PAH mineralization. Copyright © 2016 Elsevier B.V. All rights reserved.

Enhancement of removal of SO2 and NOx by powdery materials in radiation treatment of exhaust gases

International Nuclear Information System (INIS)

Tokunaga, Okihiro; Namba, Hideki; Suzuki, Nobutake

1985-01-01

We studied the effect of powdery silica on radiation removal of SO 2 and NOx from mixtures of SO 2 , NOx, water vapour, oxygen and nitrogen under irradiation by electron beams of 1.5 MeV at 120 0 C. The SO 2 and NOx concentrations decreased when powdery silica was fed without irradiation. Decrements of SO 2 and NOx concentrations were markedly enhanced when powdery silica was fed together with the irradiation. The enhancement of SO 2 - and NOx-removal is attributed to the adsorption of SO 2 and NO on the water-covered surface of powdery silica, and the effective removal of NO 2 due to the reaction with water adsorbed on the surface of powdery silica. The results obtained show that the addition of powdery silica under irradiation is an effective method of enhancing the removal of SO 2 and NOx. (author)

Phyto-enhanced remediation of soil co-contaminated with lead and diesel fuel using biowaste and Dracaena reflexa: A laboratory study.

Science.gov (United States)

Dadrasnia, Arezoo; Pariatamby, Agamuthu

2016-03-01

In phytoremediation of co-contaminated soil, the simultaneous and efficient remediation of multiple pollutants is a major challenge rather than the removal of pollutants. A laboratory-scale experiment was conducted to investigate the effect of 5% addition of each of three different organic waste amendments (tea leaves, soy cake, and potato skin) to enhance the phytoaccumulation of lead (60 mg kg(-1)) and diesel fuel (25,000 mg kg(-1)) in co-contaminated soil by Dracaena reflexa Lam for a period of 180 day. The highest rate of oil degradation was recorded in co-contaminated soil planted with D. reflexa and amended with soy cake (75%), followed by potato skin (52.8%) and tea leaves (50.6%). Although plants did not accumulate hydrocarbon from the contaminated soil, significant bioaccumulation of lead in the roots and stems of D. reflexa was observed. At the end of 180 days, 16.7 and 9.8 mg kg(-1) of lead in the stems and roots of D. reflexa were recorded, respectively, for the treatment with tea leaves. These findings demonstrate the potential of organic waste amendments in enhancing phytoremediation of oil and bioaccumulation of lead. © The Author(s) 2015.

Optimization of Lead Removal via Napier Grass in Synthetic Brackish Water using Response Surface Model

Science.gov (United States)

Hongsawat, P.; Suttiarporn, P.; Wutsanthia, K.; Kongsiri, G.

2018-03-01

The efficiency of the lead (Pb) phytoremediation by Napier grass was studied on the plant’s growth and plant’s tolerance on the Pb toxicity in synthetic brackish water. It was found that the plant was high tolerance to high level of Pb concentration (10 mg/l) in synthetic brackish water. Which revealed on the possibilities of plant’s growth under the presence of Pb contaminated condition. According to the Pb removal efficiency, the highest one (88.63±4.9%) was found at 10 ppm Pb concentration, 0.3 g/l NaCl concentration during the period 45 day. However, this study investigated the optimum condition for lead (Pb) removal from synthetic brackish water using phytoremediation treatment with Napier grass through a Box-Behnken Design. Three operational variables, i.e. Pb concentration (1, 5.5, 10 mg/l), NaCl (0.1, 0.3, 0.5 g/l) and period time (7, 26, 45 day), were determined. The results were provided evidence that the highest Pb removal efficiency (93.56%) from synthetic brackish water via Napier grass was Pb and NaCl concentration at 10 mg/l and 0.5 g/l during 45 day.

Biological characterization of lead-enhanced exopolysaccharide produced by a lead resistant Enterobacter cloacae strain P2B.

Science.gov (United States)

Naik, Milind Mohan; Pandey, Anju; Dubey, Santosh Kumar

2012-09-01

A lead resistant bacterial strain isolated from effluent of lead battery manufacturing company of Goa, India has been identified as Enterobacter cloacae strain P2B based on morphological, biochemical characters, FAME profile and 16S rDNA sequence data. This bacterial strain could resist lead nitrate up to 1.6 mM. Significant increase in exopolysaccharide (EPS) production was observed as the production increased from 28 to 108 mg/L dry weight when exposed to 1.6 mM lead nitrate in Tris buffered minimal medium. Fourier-transformed infrared spectroscopy of this EPS revealed presence of several functional groups involved in metal binding viz. carboxyl, hydroxyl and amide groups along with glucuronic acid. Gas chromatography coupled with mass spectrometry analysis of alditol-acetate derivatives of acid hydrolysed EPS produced in presence of 1.6 mM lead nitrate demonstrated presence of several neutral sugars such as rhamnose, arabinose, xylose, mannose, galactose and glucose, which contribute to lead binding hydroxyl groups. Scanning electron microscope coupled with energy dispersive X-ray spectrometric analysis of this lead resistant strain exposed to 1.6 mM lead nitrate interestingly revealed mucous EPS surrounding bacterial cells which sequestered 17 % lead (as weight %) extracellularly and protected the bacterial cells from toxic effects of lead. This lead resistant strain also showed multidrug resistance. Thus these results significantly contribute to better understanding of structure, function and environmental application of lead-enhanced EPSs produced by bacteria. This lead-enhanced biopolymer can play a very important role in bioremediation of several heavy metals including lead.

Novel chitosan/PVA/zerovalent iron biopolymeric nanofibers with enhanced arsenic removal applications.

Science.gov (United States)

Chauhan, Divya; Dwivedi, Jaya; Sankararamakrishnan, Nalini

2014-01-01

Enhanced removal application of both forms of inorganic arsenic from arsenic-contaminated aquifers at near-neutral pH was studied using a novel electrospun chitosan/PVA/zerovalent iron (CPZ) nanofibrous mat. CPZ was carefully examined using scanning electron microscopy (SEM) equipped with energy-dispersive X-ray analysis (EDX), transmission electron microscopy (TEM), atomic fluorescence spectroscopy (AFM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and thermal gravimetric analysis (TGA). Application of the adsorbent towards the removal of total inorganic arsenic in batch mode has also been studied. A suitable mechanism for the adsorption has also been discussed. CPZ nanofibers mat was found capable to remove 200.0±10.0 mg g(-1) of As(V) and 142.9±7.2 mg g(-1) of As(III) from aqueous solution of pH 7.0 at ambient condition. Addition of ethylenediaminetetraacetic acid (EDTA) enabled the stability of iron in zerovalent state (ZVI). Enhanced capacity of the fibrous mat could be attributed to the high surface area of the fibers, presence of ZVI, and presence of functional groups such as amino, carboxyl, and hydroxyl groups of the chitosan and EDTA. Both Langmuir and Freundlich adsorption isotherms were applicable to describe the removal process. The possible mechanism of adsorption has been explained in terms of electrostatic attraction between the protonated amino groups of chitosan/arsenate ions and oxidation of arsenite to arsenate by Fentons generated from ZVI and subsequent complexation of the arsenate with the oxidized iron. These CPZ nanofibrous mats has been prepared with environmentally benign naturally occurring biodegradable biopolymer chitosan, which offers unique advantage in the removal of arsenic from contaminated groundwater.

An efficient strategy for enhancing traffic capacity by removing links in scale-free networks

International Nuclear Information System (INIS)

Huang, Wei; Chow, Tommy W S

2010-01-01

An efficient link-removal strategy, called the variance-of-neighbor-degree-reduction (VNDR) strategy, for enhancing the traffic capacity of scale-free networks is proposed in this paper. The VNDR strategy, which considers the important role of hub nodes, balances the amounts of packets routed from each node to the node's neighbors. Compared against the outcomes of strategies that remove links among hub nodes, our results show that the traffic capacity can be greatly enhanced, especially under the shortest path routing strategy. It is also found that the average transport time is effectively reduced by using the VNDR strategy only under the shortest path routing strategy

Supported liquid membrane based removal of lead(II) and cadmium(II) from mixed feed: Conversion to solid waste by precipitation.

Science.gov (United States)

Bhatluri, Kamal Kumar; Manna, Mriganka Sekhar; Ghoshal, Aloke Kumar; Saha, Prabirkumar

2015-12-15

Simultaneous removal of two heavy metals, lead(II) and cadmium(II), from mixed feed using supported liquid membrane (SLM) based technique is investigated in this work. The carrier-solvent combination of "sodium salt of Di-2-ethylhexylphosphoric acid (D2EHPA) (4% w/w) in environmentally benign coconut oil" was immobilized into the pores of solid polymeric polyvinylidene fluoride (PVDF) support. Sodium carbonate (Na2CO3) was used as the stripping agent. Carbonate salts of lead(II) and cadmium(II) were formed in the stripping side interface and they were insoluble in water leading to precipitation inside the stripping solution. The transportation of solute is positively affected due to the precipitation. Lead(II) removal was found to be preferential due to its favorable electronic configuration. The conversion of the liquid waste to the solid one was added advantage for the final removal of hazardous heavy metals. Copyright © 2015 Elsevier B.V. All rights reserved.

Recent developments in the biochemistry and ecology of enhanced biological phosphorus removal

NARCIS (Netherlands)

Kortstee, GJJ; Appeldoorn, KJ; Bonting, CFC; van Niel, EWJ; van Veen, HW

Most of the genes encoding the enzymes involved in polyP synthesis and degradation and in phosphate transport have been studied in various Gram-negative bacteria. Progress has also been made in studying the biochemical mechanisms underlying the process of enhanced biological phosphorus removal

Recent developments in the biochemistry and ecology of enhanced biological phosphorus removal

NARCIS (Netherlands)

Kortstee, G.J.J.; Appeldoorn, K.J.; Bonting, C.F.C.; Niel, van E.W.J.; Veen, van H.W.

2000-01-01

Most of the genes encoding the enzymes involved in polyP synthesis and degradation and in phosphate transport have been studied in various Gram-negative bacteria. Progress has also been made in studying the biochemical mechanisms underlying the process of enhanced biological phosphorus removal

Removal of Lead Ions From Waste streams Using Flowing-Through Porous Electrodes

International Nuclear Information System (INIS)

El-Deab, M.S.; Saleh, M.M.; El-Anadouli, B.E.; Ateya, B.G.

1999-01-01

Packed bed electrodes, made of stacked screens, have been used as cathodes for the removal of lead ions from flowing alkaline electrolytes. We consider the coulombic efficiency ξ =ipb/(ipb+iH), and the collection efficiency given by ψ=i L (exp)/nFvc, where i L (exp) is the geometric limiting current for lead deposition. Two regions are defined in the current-potential relations, depending on whether hydrogen evolution does, or does not, contribute to the measured current, corresponding to ξ less than, or equal to, 100%, respectively. The geometric limiting current, i L (exp), increases with increase of v. The collection efficiency ψ increases as v decreases and/or L increases. Operating the cell at higher flow rates increases the overall coulombic efficiency, over a broader range of cell currents

Enhanced performance of denitrifying sulfide removal process under micro-aerobic condition

International Nuclear Information System (INIS)

Chen Chuan; Ren Nanqi; Wang Aijie; Liu Lihong; Lee, Duu-Jong

2010-01-01

The denitrifying sulfide removal (DSR) process with bio-granules comprising both heterotrophic and autotrophic denitrifiers can simultaneously convert nitrate, sulfide and acetate into di-nitrogen gas, elementary sulfur and carbon dioxide, respectively, at high loading rates. This study determines the reaction rate of sulfide oxidized into sulfur, as well as the reduction of nitrate to nitrite, would be enhanced under a micro-aerobic condition. The presence of limited oxygen mitigated the inhibition effects of sulfide on denitrifier activities, and enhanced the performance of DSR granules. The advantages and disadvantages of applying the micro-aerobic condition to the DSR process are discussed.

Quantitative evaluation of enhanced laser tattoo removal by skin optical clearing

Directory of Open Access Journals (Sweden)

Caihua Liu

2015-05-01

Full Text Available Lasers have been widely used for tattoo removal, but the limited light penetration depth caused by high skin scattering property restricts the therapeutic outcome of deep tattoo. Skin optical clearing method, by introducing optical clearing agent (OCA into skin, has shown some improvement in the effect of laser tattoo removal. In this study, the enhanced laser tattoo removal has been quantitatively assessed. OCA was applied to the skin of tattoo animal model and Q-switched Nd:YAG laser (1064 nm irradiation was used to remove the tattoo. The skin evaluation instrument (Mexameter probe, MPA580 was applied to measure the content of tattoo pigment before and after laser treatment, and then the clearance rate of pigment was calculated. Further, Monte Carlo (MC method was utilized to simulate the effect of skin optical clearing on light transmission in tattoo skin model. By comparing the pigment change of tattoo areas respectively treated with OCA plus laser and single laser, it was found that pigment clearance of the former tattoo area was increased by 1.5-fold. Further, the MC simulation verified that the reduced light scattering in skin could increase the effective dose of luminous flux reaching to the deep tattoo regions. It can be concluded from both experiment and theoretical simulations that skin optical clearing technique could improve the outcome of laser tattoo removal, which should be beneficial for clinical laser tattoo removal and other laser pigment elimination.

Laboratory studies on the removal of radon-born lead from KamLAND's organic liquid scintillator

Energy Technology Data Exchange (ETDEWEB)

Keefer, G., E-mail: gregkeefer@llnl.gov [Department of Physics and Astronomy, University of Alabama, Tuscaloosa, AL 35487 (United States); Grant, C. [Department of Physics and Astronomy, University of Alabama, Tuscaloosa, AL 35487 (United States); Piepke, A. [Department of Physics and Astronomy, University of Alabama, Tuscaloosa, AL 35487 (United States); Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa 277-8583 (Japan); Ebihara, T.; Ikeda, H. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Kishimoto, Y. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa 277-8583 (Japan); Kibe, Y.; Koseki, Y.; Ogawa, M.; Shirai, J.; Takeuchi, S. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Mauger, C.; Zhang, C. [W.K. Kellogg Radiation Laboratory, California Institute of Technology, Pasadena, CA 91125 (United States); Schweitzer, G. [Department of Chemistry, University of Tennessee, Knoxville, TN 37996 (United States); Berger, B.E. [Department of Physics, Colorado State University, Fort Collins, CO 80523 (United States); Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa 277-8583 (Japan); Dazeley, S. [Department of Physics and Astronomy, Louisiana State University, Baton Rouge, LA 70803 (United States); Decowski, M.P. [Physics Department, University of California, Berkeley, Berkeley, CA 94720 (United States); Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa 277-8583 (Japan); Detwiler, J.A. [Physics Department, University of California, Berkeley, Berkeley, CA 94720 (United States); Djurcic, Z. [Department of Physics and Astronomy, University of Alabama, Tuscaloosa, AL 35487 (United States); and others

2015-01-01

The removal of radioactivity from liquid scintillator has been studied in preparation of a low background phase of KamLAND. This paper describes the methods and techniques developed to measure and efficiently extract radon decay products from liquid scintillator. We report the radio-isotope reduction factors obtained when applying various extraction methods. During this study, distillation was identified as the most efficient method for removing radon-born lead from liquid scintillator.

Removal of cadmium, copper, lead and zinc from simulated industrial effluents using silica powder

International Nuclear Information System (INIS)

Javed, T.; Awan, A.; Arshad, M.; Khan, S.N.

2013-01-01

Rapid industrial development have led to the recognition and increasing understanding of interrelationship between pollution, public health and environment. Industrial development results in the generation of industrial effluents, and if untreated results in water, sediment and soil pollution. In Pakistan most of the industrial effluents are discharged into surrounding ecosystems without any treatment. Industrial wastes and emission contain toxic and hazardous substances, most of which are detrimental to human health. Extensive efforts are being made around the world for the removal of heavy metal from industrial effluents. A laboratory scale study was designed for removal of Cd, Cu, Pb and Zn from simulated solutions at various weight of silica (0.5gm, 1gm, 2 gm, 3gm and 4 gm), Voltammeter was used to quantify the metals. Maximum removal of all metals was achieved with 4 gm of silica. Absorption of lead onto silic a was higher than other metals. (author)

Enhancing mercury removal across air pollution control devices for coal-fired power plants by desulfurization wastewater evaporation.

Science.gov (United States)

Bin, Hu; Yang, Yi; Cai, Liang; Yang, Linjun; Roszak, Szczepan

2017-10-09

Desulfurization wastewater evaporation technology is used to enhance the removal of gaseous mercury (Hg) in conventional air pollution control devices (APCDs) for coal-fired power plants. Studies have affirmed that gaseous Hg is oxidized and removed by selective catalytic reduction (SCR), an electrostatic precipitator (ESP) and wet flue gas desulfurization (WFGD) in a coal-fired thermal experiment platform with WFGD wastewater evaporation. Effects of desulfurization wastewater evaporation position, evaporation temperature and chlorine ion concentration on Hg oxidation were studied as well. The Hg 0 oxidation efficiency was increased ranging from 30% to 60%, and the gaseous Hg removal efficiency was 62.16% in APCDs when wastewater evaporated before SCR. However, the Hg 0 oxidation efficiency was 18.99% and the gaseous Hg removal efficiency was 40.19% in APCDs when wastewater evaporated before ESP. The results show that WFGD wastewater evaporation before SCR is beneficial to improve the efficiency of Hg oxidized and removed in APCDs. Because Hg 2+ can be easily removed in ACPDs and WFGD wastewater in power plants is enriched with chlorine ions, this method realizes WFGD wastewater zero discharge and simultaneously enhances Hg removal in APCDs.

Effect of bioaugmentation to enhance phytoremediation for removal of phenanthrene and pyrene from soil with Sorghum and Onobrychis sativa

Science.gov (United States)

2014-01-01

The use of plants to remove Poly-aromatic-hydrocarbons (PAHs) from soil (phytoremediation) is emerging as a cost-effective method. Phytoremediation of contaminated soils can be promoted by the use of adding microorganisms with the potential of pollution biodegradation (bioaugmentation). In the present work, the effect of bacterial consortium was studied on the capability of Sorghum and Onobrychis sativa for the phytoremediation of soils contaminated with phenanthrene and pyrene. 1.5 kg of the contaminated soil in the ratio of 100 and 300 mg phenanthrene and/or pyrene per kg of dry soil was then transferred into each pot (nine modes). The removal efficiency of natural, phytoremediation and bioaugmentation, separately and combined, were evaluated. The samples were kept under field conditions, and the remaining concentrations of pyrene and phenanthrene were determined after 120 days. The rhizosphere as well as the microbial population of the soil was also determined. Results indicated that both plants were able to significantly remove pyrene and phenanthrene from the contaminated soil samples. Phytoremediation alone had the removal efficiency of about 63% and 74.5% for pyrene and phenanthrene respectively. In the combined mode, the removal efficiency dramatically increased, leading to pyrene and phenanthrene removal efficiencies of 74.1% and 85.02% for Onobrychis sativa and 73.84% and 85.2% for sorghum, respectively. According to the results from the present work, it can be concluded that Onobrychis sativa and sorghum are both efficient in removing pyrene and phenanthrene from contamination and bioaugmentation can significantly enhance the phytoremediation of soils contaminated with pyrene and phenanthrene by 22% and 16% respectively. PMID:24406158

A Personal Perspective on the Initial Federal Health-Based Regulation to Remove Lead from Gasoline

Science.gov (United States)

Bridbord, Kenneth; Hanson, David

2009-01-01

Objective This article describes the personal experience and perspective of the authors, who had primary responsibility for drafting the initial health-based regulation limiting lead content of gasoline during the early 1970s while employed by the U.S. Environmental Protection Agency (EPA). Data source Information used by the U.S. EPA in developing the initial health-based regulation limiting lead content of gasoline in December 1973 and studies documenting the impact of that and subsequent actions. Data extraction Among the lessons learned from this experience is the importance of having input from independent scientists to the regulatory decision-making process. This also demonstrates the critical role of independent peer-reviewed research, such as that supported by the National Institutes of Health, as well as research conducted by scientists from the Centers for Disease Control and Prevention, in delineating the consequences of lead exposure in the population. Data synthesis Removal of lead from gasoline in the United States has been described as one of the great public health achievements of the 20th century, but it almost did not happen. The experience of the authors in developing this regulation may be helpful to others involved in developing health-based regulatory policy in the future. Conclusion The initial U.S. EPA health-based regulation to remove lead from gasoline is clearly an example where science successfully affected public policy. The leadership of the U.S. EPA at that time deserves much credit for establishing an atmosphere in which this was possible. PMID:19672397

Removal of Lead (II from Aqueous Solution Using Chitosan Impregnated Granular Activated Carbon

Directory of Open Access Journals (Sweden)

Ali Mousa Ridha

2017-03-01

Full Text Available The use of biopolymer material Chitosan impregnated granular activated carbon CHGAC as adsorbent in the removal of lead ions pb.2+ from aqueous solution was studied using batch adsorption mode. The prepared CHGAC was characterized by Scanning Electronic Microscopy (SEM and atomic-absorption pectrophotometer. The adsorption of lead ions onto Chitosan-impregnated granular activated carbon was examined as a function of adsorbent weight, pH and contact time in Batch system. Langmuir and Freundlich models were employed to analyze the resulting experimental data demonstrated that better fitted by Langmuir isotherm model than Freundlich model, with good correlation coefficient. The maximum adsorption capacity calculated from the pseudo second order model in conformity to the experimental values. This means that the adsorption performance of lead ions onto CHGAC follows a pseudo second order model, which illustrates that the adsorption of Pb2+ onto CHGAC was controlled by chemisorption. The granular activated carbon GAC impregnated by Chitosan was effectively applied as adsorbent for the elimination of lead ions from aqueous solution.

Removal of polonium contamination by lead-bismuth eutectic in nuclear systems

International Nuclear Information System (INIS)

Miura, Terumitsu; Obara, Toru; Sekimoto, Hiroshi

2003-01-01

Lead-Bismuth eutectic (LBE) is considered as a promising candidate of the coolant of liquid metal cooled fast reactor, and the coolant and/or target of accelerator driven system. LBE has various good characters for coolant, but it has also some problems such as polonium production. It is necessary to take polonium contamination into consideration, when LBE is used as the coolant. In the present paper, the removal of contaminating polonium from material surface is studied. Baking method is investigated for polonium removal from contaminated quartz glass plate in vacuum. Before and after baking, the mass of the contaminants on the surface and alpha particle counts from contaminated surface is measured. When the contaminated quartz glass plates are baked at more than 400degC for a few minutes, alpha particle counts from the surface decreases by more than 99.7%, and the mass of contaminants decreases by more than 50%. When the baking was performed at 300degC for 15 minutes and more, alpha particle count decreases by more than 80%, and the mass decreases in little. When, the baking temperature is lower than 200degC, alpha particle counts and mass do not decrease. (author)

Despina Hatzifotiadou: ALICE Master Class 3 - Theory: strangeness enhancement; centrality of lead-lead collisions; efficiency, yield, background etc

CERN Multimedia

CERN. Geneva

2016-01-01

This is the 3rd of 4 short online videos. It explains what is: strangeness enhancement; centrality of lead-lead collisions; efficiency, yield, background etc. More details and related links on this indico event page. In more detail: What is Physics Master Classes Students after morning lectures, run programmes in the afternoon to do measurements. These tutorials are about how to use the software required to do these measurements. Background info and examples  Looking for strange particles with ALICE http://aliceinfo.cern.ch/Public/MasterCL/MasterClassWebpage.html Introduction to first part of the exercise : what are strange particles, V0 decays, invariant mass. Demonstration of the software for the 1st part of the exercise - visual identification of V0s Introduction to second part of the exercise : strangeness enhancement; centrality of lead-lead collisions; explanation of efficiency, yield, background etc Demonstration of the software for the 2nd part of the exercise - invariant mass spectr...

Integration of pneumatic fracturing with bioremediation from the enhanced removal of BTX from low permeability gasoline-contaminated soils

International Nuclear Information System (INIS)

Venkatraman, S.N.; Kosson, D.S.; Schuring, J.R.; Boland, T.M.

1995-01-01

A pilot-scale evaluation of the integrated pneumatic fracturing and bioremediation system was carried out to demonstrate the enhanced removal of BTX from a gasoline contaminated, low permeability soil formation. The fracturing enhanced subsurface permeability by an average of over 36 times, and established an extended bioremediation zone supporting aerobic, denitrifying and methanogenic populations. Subsurface amendment injections consisting of phosphate and nitrogen were made periodically over a 50-week period to stimulate microbial activity. Results indicate that 79% of the soil-phase BTX was removed during the field test, with over 85% of the mass removed attributable to bioremediation

Effective removal of trace thallium from surface water by nanosized manganese dioxide enhanced quartz sand filtration.

Science.gov (United States)

Huangfu, Xiaoliu; Ma, Chengxue; Ma, Jun; He, Qiang; Yang, Chun; Zhou, Jian; Jiang, Jin; Wang, Yaan

2017-12-01

Thallium (Tl) has drawn wide concern due to its high toxicity even at extremely low concentrations, as well as its tendency for significant accumulation in the human body and other organisms. The need to develop effective strategies for trace Tl removal from drinking water is urgent. In this study, the removal of trace Tl (0.5 μg L -1 ) by conventional quartz sand filtration enhanced by nanosized manganese dioxide (nMnO 2 ) has been investigated using typical surface water obtained from northeast China. The results indicate that nMnO 2 enhanced quartz sand filtration could remove trace Tl(I) and Tl(III) efficiently through the adsorption of Tl onto nMnO 2 added to a water matrix and onto nMnO 2 attached on quartz sand surfaces. Tl(III)-HA complexes might be responsible for higher residual Tl(III) in the effluent compared to residual Tl(I). Competitive Ca 2+ cations inhibit Tl removal to a certain extent because the Ca 2+ ions will occupy the Tl adsorption site on nMnO 2 . Moreover, high concentrations of HA (10 mgTOC L -1 ), which notably complexes with and dissolves nMnO 2 (more than 78%), resulted in higher residual Tl(I) and Tl(III). Tl(III)-HA complexes might also enhance Tl(III) penetration to a certain extent. Additionally, a higher pH level could enhance the removal of trace Tl from surface water. Finally, a slight increase of residual Tl was observed after backwash, followed by the reduction of the Tl concentration in the effluent to a "steady" state again. The knowledge obtained here may provide a potential strategy for drinking water treatment plants threatened by trace Tl. Copyright © 2017. Published by Elsevier Ltd.

Enhanced performance of denitrifying sulfide removal process under micro-aerobic condition.

Science.gov (United States)

Chen, Chuan; Ren, Nanqi; Wang, Aijie; Liu, Lihong; Lee, Duu-Jong

2010-07-15

The denitrifying sulfide removal (DSR) process with bio-granules comprising both heterotrophic and autotrophic denitrifiers can simultaneously convert nitrate, sulfide and acetate into di-nitrogen gas, elementary sulfur and carbon dioxide, respectively, at high loading rates. This study determines the reaction rate of sulfide oxidized into sulfur, as well as the reduction of nitrate to nitrite, would be enhanced under a micro-aerobic condition. The presence of limited oxygen mitigated the inhibition effects of sulfide on denitrifier activities, and enhanced the performance of DSR granules. The advantages and disadvantages of applying the micro-aerobic condition to the DSR process are discussed. 2010 Elsevier B.V. All rights reserved.

Phosphorous removal from aqueous solution can be enhanced through the calcination of lime sludge.

Science.gov (United States)

Bal Krishna, K C; Niaz, Mohamed R; Sarker, Dipok C; Jansen, Troy

2017-09-15

Water treatment plants generate an enormous amount of the sludge which is normally treated as waste. In the recent past, many investigations have been focused on developing an economical adsorbent using water treatment sludge to remove phosphorous (P) from aqueous solutions. However, the great extents of the studies have been limited in the use of alum- and iron-based sludges. This study, therefore, investigated the P removal performance of the calcined lime sludge. Calcined lime sludge at 700 °C significantly enhanced the P removal efficiency whereas marginal improvement was noted when the sludge calcined at 400 °C was tested. With increase P removal efficiency, final pH values of the solution also significantly increased. P removal efficiency of the calcined sludge decreased with increasing the initial P concentrations. However, the removal efficiency could be improved by increasing the weight of the sludge. Further analysis demonstrated that P removal trend followed both pseudo-second order and diffusion-chemisorption kinetics signifying the P removal is potentially due to a multi-mechanistic reaction in which, the process is controlled by intra-particle diffusion followed by chemisorptions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Kape barako (coffea liberica) grounds as adsorbent for the removal of lead in lead-enriched Marikina river water samples

International Nuclear Information System (INIS)

Valera, Florenda S.; Garcia, Jhonard John L.

2015-01-01

Kape Barako (Coffee liberica) grounds (residue left after brewing ground coffee) were used as adsorbent for the removal of lead in Marikina River water samples. The sundried coffee grounds showed 9.30% moisture after drying in the oven. The coffee grounds were determined using Shimadzu AA-6501S Atomic Adsorption Spectrometer. The lead concentration was determined to be 4.7 mg/kg in coffee grounds and below detection limit in the Marikina River water samples. The adsorption studies were done at room temperature, and the optimized parameters were a contact time of 3 hours, an adsorbent dose of 3.0 g/L and 4.0 mg/L Pb-enriched water samples. The maximum uptake capacity was found to be 14.2 mg of lead/g adsorbent. The adsorption studies were done at room temperature, and the optimized parameters were a contact time of 3 hours, an adsorbent dose of 3.0 g/L and 4.0 mg/L Pb-enriched water samples. Analyses of the coffee grounds before and after lead adsorption using Shimadzu IR-Affinity-I Fourier Transform Infrared Spectrometer showed marked difference in the spectra, indicating interaction between Pb and the functional groups of the coffee grounds. (author)

Enhancement of plaque removal by baking soda toothpastes from less accessible areas in the dentition.

Science.gov (United States)

Thong, S; Hooper, W; Xu, Y; Ghassemi, A; Winston, A

2011-01-01

To determine if baking soda toothpastes are relatively more effective than non-baking soda toothpastes in promoting plaque removal from less accessible sites in the dentition. Several single-brushing comparisons of baking soda and non-baking soda toothpastes for their overall ability to remove plaque have been published. In this study, individual comparisons of these published data, comparing the plaque removal performance of baking soda and non-baking soda toothpastes at various sites in the dentition, were examined to see if there were any site-dependant performance trends. The site-specific single-brushing data were then combined and analyzed in two ways. Meta-analyses of the clinical studies were performed to compare baking soda's relative plaque removal advantage at various sites in the mouth using paired t-testing at p baking soda toothpastes were graphically compared with plaque index reductions due to brushing with non-baking soda dentifrices. The percent relative plaque removal advantage for baking soda toothpastes at various sites were plotted against the reduction in plaque index due to brushing with non-baking soda toothpastes. Individual comparisons showed that brushing with the toothpastes containing baking soda generally removed significantly more plaque from each site than brushing with toothpastes without baking soda. The relative efficacy advantage for baking soda toothpastes was consistently higher at sites where the non-baking soda toothpastes removed less plaque. Meta-analytical comparisons confirmed baking soda toothpastes to be relatively more effective in enhancing plaque removal from sites where less plaque was removed compared to brushing with non-baking soda toothpastes (p baking soda toothpastes' relative plaque removal advantage could be seen to increase hyperbolically with decreasing plaque removal by the non-baking soda toothpastes with which they were compared. We presuppose that the reason less plaque is removed by non-baking soda

Using Magnetically Responsive Tea Waste to Remove Lead in Waters under Environmentally Relevant Conditions

KAUST Repository

Yeo, Siang Yee

2013-06-20

We report the use of a simple yet highly effective magnetite-waste tea composite to remove lead(II) (Pb2+) ions from water. Magnetite-waste tea composites were dispersed in four different types of water–deionized (DI), artificial rainwater, artificial groundwater and artificial freshwater–that mimic actual environmental conditions. The water samples had varying initial concentrations (0.16–5.55 ppm) of Pb2+ ions and were mixed with the magnetite-waste tea composite for at least 24 hours to allow adsorption of the Pb2+ ions to reach equilibrium. The magnetite-waste tea composites were stable in all the water samples for at least 3 months and could be easily removed from the aqueous media via the use of permanent magnets. We detected no significant leaching of iron (Fe) ions into the water from the magnetite-waste tea composites. The percentage of Pb adsorbed onto the magnetite-waste tea composite ranged from ~70% to 100%; the composites were as effective as activated carbon (AC) in removing the Pb2+ ions from water, depending on the initial Pb concentration. Our prepared magnetite-waste tea composites show promise as a green, inexpensive and highly effective sorbent for removal of Pb in water under environmentally realistic conditions.

Using Magnetically Responsive Tea Waste to Remove Lead in Waters under Environmentally Relevant Conditions

KAUST Repository

Yeo, Siang Yee; Choi, Siwon; Dien, Vivian; Sow-Peh, Yoke Keow; Qi, Genggeng; Hatton, T. Alan; Doyle, Patrick S.; Thio, Beng Joo Reginald

2013-01-01

We report the use of a simple yet highly effective magnetite-waste tea composite to remove lead(II) (Pb2+) ions from water. Magnetite-waste tea composites were dispersed in four different types of water–deionized (DI), artificial rainwater, artificial groundwater and artificial freshwater–that mimic actual environmental conditions. The water samples had varying initial concentrations (0.16–5.55 ppm) of Pb2+ ions and were mixed with the magnetite-waste tea composite for at least 24 hours to allow adsorption of the Pb2+ ions to reach equilibrium. The magnetite-waste tea composites were stable in all the water samples for at least 3 months and could be easily removed from the aqueous media via the use of permanent magnets. We detected no significant leaching of iron (Fe) ions into the water from the magnetite-waste tea composites. The percentage of Pb adsorbed onto the magnetite-waste tea composite ranged from ~70% to 100%; the composites were as effective as activated carbon (AC) in removing the Pb2+ ions from water, depending on the initial Pb concentration. Our prepared magnetite-waste tea composites show promise as a green, inexpensive and highly effective sorbent for removal of Pb in water under environmentally realistic conditions.

Optimization of enhanced biological phosphorus removal after periods of low loading.

Science.gov (United States)

Miyake, Haruo; Morgenroth, Eberhard

2005-01-01

Enhanced biological phosphorus removal is a well-established technology for the treatment of municipal wastewater. However, increased effluent phosphorus concentrations have been reported after periods (days) of low organic loading. The purpose of this study was to evaluate different operating strategies to prevent discharge of effluent after such low-loading periods. Mechanisms leading to these operational problems have been related to the reduction of polyphosphate-accumulating organisms (PAOs) and their storage compounds (polyhydroxy alkanoates [PHA]). Increased effluent phosphorus concentrations can be the result of an imbalance between influent loading and PAOs in the system and an imbalance between phosphorus release and uptake rates. The following operating conditions were tested in their ability to prevent a reduction of PHA and of overall biomass during low organic loading conditions: (a) unchanged operation, (b) reduced aeration time, (c) reduced sludge wastage, and (d) combination of reduced aeration time and reduced sludge wastage. Experiments were performed in a laboratory-scale anaerobic-aerobic sequencing batch reactor, using acetate as the carbon source. Without operational adjustments, phosphorus-release rates decreased during low-loading periods but recovered rapidly. Phosphorus-uptake rates also decreased, and the recovery typically required several days to increase to normal levels. The combination of reduced aeration time and reduced sludge wastage allowed the maintenance of constant levels of both PHA and overall biomass. A mathematical model was used to explain the influence of the tested operating conditions on PAO and PHA concentrations. While experimental results were in general agreement with model predictions, the kinetic expression for phosphorus uptake deviated significantly for the first 24 hours after low-loading conditions. Mechanisms leading to these deviations need to be further investigated.

Enhancing phosphorus removal in constructed wetlands with ochre from mine drainage treatment.

Science.gov (United States)

Heal, K V; Dobbie, K E; Bozika, E; McHaffie, H; Simpson, A E; Smith, K A

2005-01-01

No single end-use has yet been identified that is capable of consuming the projected production of ochre (mainly iron (III) oxides) from mine drainage treatment. However, the high sorption capacity of ochre for phosphorus (up to 26 mg kg(-1)) means that it could be used in constructed wetlands to enhance phosphorus removal. Laboratory batch experiments showed that coarse-grained ochre removes 90% of all phosphorus forms from sewage effluent after 15 minutes of shaking. From a larger-scale experiment, it is estimated that constructed wetlands with an ochre substrate should remove phosphorus from sewage effluent for up to 200-300 years. The suitability of ochre for phosphorus removal is being investigated at the field scale in a wastewater constructed wetland (175 m2 area) in Berwickshire, UK. The hydraulic and treatment performance of the wetland were monitored for 15 months prior to installation at the inlet in November 2003 of a tank containing approximately 1200 kg ochre. Results so far show that improved hydraulic design is required for ochre to increase the mean phosphorus removal efficiency of the system (27 +/- 28%), but potentially toxic metals (Al, Cd, Cr, Cu, Fe, Ni, Pb, Zn) have not been released from the ochre into the wetland outflow.

Enhanced heat rectification effect in a quantum dot connected to ferromagnetic leads

Energy Technology Data Exchange (ETDEWEB)

Chi, Feng, E-mail: chifeng@semi.ac.cn [School of Physical Science and Technology, Inner Mongolia University, Huhehaote 010023 (China); College of Engineering, Bohai University, Jinzhou 121013 (China); Sun, Lian-Liang [College of Science, North China University of Technology, Beijing 100041 (China); Zheng, Jun; Guo, Yu [College of Engineering, Bohai University, Jinzhou 121013 (China)

2015-06-15

We study theoretically the heat generation by electric current in an interacting single level quantum-dot connected to ferromagnetic leads. The heat is transferred between the dot and the lattice vibration of its host material (phonon reservoir). Particular attention is paid on the heat's rectification effect achieved by properly arranging the dot level and the bias voltage. We find that this effect is remarkably enhanced when the two leads' magnetic moments are in antiparallel configuration, i.e., the magnitude of the heat generation is reduced (amplified) in the negative (positive) bias regime as compared to the cases of parallel configuration and nonmagnetic leads. The rectification effect is even enhanced when one of the lead's spin polarization approaches to unit, during which the negative differential of the heat generation is weakened due to the change of the spin-dependent electron occupation numbers on the dot. The found results may be used for thermal transistor in the newly emerged research subject of phononics. - Highlights: • Heat flow between electrons and phonons is controlled by interaction between them. • A thermal diode or rectifier is proposed to work under electrical bias. • The heat rectification effect can be enhanced by the leads' ferromagnetism.

Removal of cadmium and lead from water by activated carbon

International Nuclear Information System (INIS)

Abdel-Shafy, H.I.; Abdel-Sabour, M.F.; El-Gamal, I.M.; Abo-El-Wafa, O.

1989-01-01

Adsorption of cadmium and lead from water by carbon was studied using powdered or granular carbon. The studied water artificially contaminated by cadmium and lead amounting to 1 mg/dm 3 each. Batch as well as continuous system were carried out. The batch system was used to determine the time to maintain equilibrium followed by adsorption isotherm. Results obtained by using the powered carbon were found to match with Freundlich's equation where 1/n was 2.12 and 2.096 for Cd and Pb, respectively. Corresponding constants (K) were 4.2·10 -2 and 76.0·10 -2 . The amount of powdered activated carbon required to reduce residual Cd and Pb concentration to 0.01 mg/dm 3 for each are 26.98 and 2.86 mg, respectively. Similar batch system study was carried out for the granular carbon. When granular carbon was used in a continuous system, two different contact times, namely 10 to 20 min were examined. The results obtained showed that increasing the contact time from 10 to 20 min increases the metal to carbon removal efficiency. The overall results indicated that the breakthrough point for either Cd or Pb is the reverse of their adsorption as indicated by K value. (author). 22 refs, 10 figs, 7 tabs

Enhanced NO{sub x} removal in wet scrubbers using metal chelates. Final report, Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-12-01

Successful pilot plant tests of simultaneous removal of SO{sub 2} and NO{sub x} in a wet lime flue gas desulfurization system were concluded in December. The test, at up to 1.5 MW(e) capacity, were conducted by the Cincinnati Gas and Electric Company and Dravo Lime Company for the US Department of Energy at a pilot plant facility at the Miami Fort station of CG&E near Cincinnati, Ohio. The pilot plant scrubbed a slipstream of flue gas from Unit 7 a 530 MW coal-fired electric generating unit. Tests were conducted in three phases between April and December. The technology tested was wet scrubbing with Thiosorbic{reg_sign} magnesium-enhanced lime for SO{sub 2} removal and simultaneous NO scrubbing with ferrous EDTA, a metal chelate. Magnesium-enhanced lime-based wet scrubbing is used at 20 full-scale high-sulfur coal-fired electric generating units with a combined capacity of 8500 MW. Ferrous EDTA reacts with nitric oxide, NO, which comprises about 96% of NO{sub x} from coal-fired boilers. In this report, although not precise, NO and NO{sub x} are used interchangeably. A major objective of the tests was to combine NO{sub x} removal using ferrous EDTA, a developing technology, with SO{sub 2} removal using wet lime FGD, already in wide commercial use. If successful, this could allow wide application of this NO{sub x} removal technology. Volume 2 covers: description and results of NO{sub x} removal tests; and description and results of waste characterization studies.

Enhanced nitrogen removal in single-chamber microbial fuel cells with increased gas diffusion areas

KAUST Repository

Yan, Hengjing

2012-11-23

Single-chamber microbial fuel cells (MFCs) with nitrifiers pre-enriched at the air cathodes have previously been demonstrated as a passive strategy for integrating nitrogen removal into current-generating bioelectrochemical systems. To further define system design parameters for this strategy, we investigated in this study the effects of oxygen diffusion area and COD/N ratio in continuous-flow reactors. Doubling the gas diffusion area by adding an additional air cathode or a diffusion cloth significantly increased the ammonia and COD removal rates (by up to 115% and 39%), ammonia removal efficiency (by up to 134%), the cell voltage and cathode potentials, and the power densities (by a factor of approximately 2). When the COD/N ratio was lowered from 13 to 3, we found up to 244% higher ammonia removal rate but at least 19% lower ammonia removal efficiency. An increase of COD removal rate by up to 27% was also found when the COD/N ratio was lowered from 11 to 3. The Coulombic efficiency was not affected by the additional air cathode, but decreased by an average of 11% with the addition of a diffusion cloth. Ammonia removal by assimilation was also estimated to understand the ammonia removal mechanism in these systems. These results showed that the doubling of gas diffusion area enhanced N and COD removal rates without compromising electrochemical performance. © 2012 Wiley Periodicals, Inc.

Evaluating the Efficiency of Air Shower in Removing Lead from Army Combat Uniform Swatches Loaded with Gunshot Residue

Science.gov (United States)

2016-03-25

about ASs ability to reduce Pb contamination on ACU resulting from activities on IFRs . The results of this study could impact the use of ASs at IFRs by...the 0-, 45-, and 90-degree angles of impact . Analysis of lead mass remaining on swatches after the exposure indicated the percent of lead removed...22 Number and Design of Nozzles ........................................................................ 23 Angle of Impact

Lead-resistant strain KQBT-3 inoculants of Tricholoma lobayensis Heim that enhance remediation of lead-contaminated soil.

Science.gov (United States)

Li, Ying; Qin, Chui-Xin; Gao, Biyu; Hu, Yuanjia; Xu, Heng

2015-01-01

To enhance lead-detoxifying efficiency of Tricholoma lobayensis Heim, one lead-resistant strain KQBT-3 (Bacillus thuringiensis) was applied owing to its excellent ability to tolerate Pb. KQBT-3 domesticated in liquid medium with increasing lead concentrations could tolerate Pb(NO3)2 up to a concentration of 800 mg L(-1). Pot experiments showed that the KQBT-3 not only could promote the growth of T. lobayensis, but also could enhance its Pb accumulation ability under heavy metal stress. Biomass and accumulation of Pb increased 47.3% and 33.2%, respectively. In addition, after inoculation of KQBT-3, the significant decrease of malondialdehyde indicated KQBT-3 could alleviate lipid peroxidation in T. lobayensis. What is interesting is that superoxide dismutase and peroxidase activities in T. lobayensis inoculated with KQBT-3 were increased, and the maximum increasing rate was 121.71% and 117.29%, respectively. However, the catalase activity increased slightly. This revealed that inoculating KQBT-3 further induced oxidative response in T. lobayensis due to Pb accumulation. Therefore, the present work showed that KQBT-3 made a major contribution to promote growth and lead uptake of T. lobayensis and alleviate the oxidative stress. This kind of auxiliary effect on macrofungi can be developed into a novel bioremediation strategy.

Performance of a modified multi-stage bubble column reactor for lead(II) and biological oxygen demand removal from wastewater using activated rice husk

International Nuclear Information System (INIS)

Sahu, J.N.; Agarwal, S.; Meikap, B.C.; Biswas, M.N.

2009-01-01

The excessive release of wastewater into the environment is a major concern worldwide. Adsorption is the one of the most effective technique for treatment of wastewater. In this work activated carbon prepared from rice husk has been used as an adsorbent. In the present investigation a three phase modified multi-stage bubble column reactor (MMBCR) has been designed to remove lead and biochemical oxygen demand (BOD) from wastewater by means of its adsorption onto the surface of activated rice husk. The multi-staging has been achieved by hydrodynamically induced continuous bubble generation, breakup and regeneration. Under optimum conditions, maximum lead and BOD reduction achieved using activated rice husk was 77.15% and 19.05%, respectively. Results showed MMBCR offered appreciated potential benefits for lead removal from wastewater and BOD removal, even this extent of removal is encouraging and the MMBCR can be used a pretreatment unit before subjecting the wastewater to biological treatment

Performance of a modified multi-stage bubble column reactor for lead(II) and biological oxygen demand removal from wastewater using activated rice husk.

Science.gov (United States)

Sahu, J N; Agarwal, S; Meikap, B C; Biswas, M N

2009-01-15

The excessive release of wastewater into the environment is a major concern worldwide. Adsorption is the one of the most effective technique for treatment of wastewater. In this work activated carbon prepared from rice husk has been used as an adsorbent. In the present investigation a three phase modified multi-stage bubble column reactor (MMBCR) has been designed to remove lead and biochemical oxygen demand (BOD) from wastewater by means of its adsorption onto the surface of activated rice husk. The multi-staging has been achieved by hydrodynamically induced continuous bubble generation, breakup and regeneration. Under optimum conditions, maximum lead and BOD reduction achieved using activated rice husk was 77.15% and 19.05%, respectively. Results showed MMBCR offered appreciated potential benefits for lead removal from wastewater and BOD removal, even this extent of removal is encouraging and the MMBCR can be used a pretreatment unit before subjecting the wastewater to biological treatment.

Factors Leading to Self-Removal from the Bariatric Surgery Program After Attending the Orientation Session.

Science.gov (United States)

Yang, Kai; Zhang, Binghao; Kastanias, Patti; Wang, Wei; Okraniec, Allan; Sockalingam, Sanjeev

2017-01-01

Bariatric surgery orientation sessions are often the first point of contact and a recommended component of pre-bariatric surgery assessment. Self-removal rates after bariatric program orientation are as high as 25 % despite the proven efficacy of this procedure. The objective of this study was to identify factors contributing to patient self-removal after orientation using a mixed method approach. Patients who attended the Toronto Western Hospital Bariatric Surgery Program orientation between 2012 and 2013 and then self-removed from the program (N = 216) were included in the study. Subjects were interviewed via telephone using a semi-structured interview guide, generating both quantitative and qualitative data. Factors leading to discontinuation were rated on a five-point Likert scale. Qualitative data was analyzed using constant comparative methodology. The response rate was 59 % with a 40.7 % completion rate (N = 88). Concerns about potential surgical risks and complications and the ability to adapt to changes in eating and drinking post-operatively were identified as the top two factors for patients' self-removal from the program. Thematic analysis uncovered 11 major themes related to patient self-removal. Unexpected themes include perceived personal suitability for the surgery, family impact of surgery, miscommunication with the family physician, and fears related to the orientation information. This is one of the first studies examining barriers to bariatric surgery in the pre-operative setting and offers new insights into the reasons patients self-remove from bariatric surgery programs. This study may inform bariatric orientation program changes resulting in improved access to this effective surgical intervention.

Using quartz sand to enhance the removal efficiency of M. aeruginosa by inorganic coagulant and achieve satisfactory settling efficiency.

Science.gov (United States)

Pei, Haiyan; Jin, Yan; Xu, Hangzhou; Ma, Chunxia; Sun, Jiongming; Li, Hongmin

2017-10-19

In this study, low-cost and non-polluting quartz sand was respectively mixed with AlCl 3 , FeCl 3 and PAFC to synergistically remove Microcystis aeruginosa. Results showed that quartz sand could markedly increase the algae removal efficiency and decrease the coagulant doses. The increase of removal efficiency with AlCl 3 and FeCl 3 was only due to the enhancement of floc density by the quartz sand. However, the removal efficiency with PAFC was increased not only by the enhanced floc density, but also by the enlarged floc size. Flocs from 50 mg/L sand addition were larger than that with other sand doses, which was on account of the appropriate enhancement of collision efficiency at this dose. After coagulation, the extracellular organic matter (EOM) and microcystins (MCs) in system with quartz sand was remarkably reduced. That's because quartz sand can enhance the coagulation so as to improve capping the EOM and MCs in flocs during coagulation process. Owing to 200 mg/L quartz sand could damage the cell's membrane during coagulation proces, algal cells in the system lysed two days earlier than with 50 mg/L sand during flocs storage. In addition, cells with PAFC incurred relatively moderate cellular oxidative damage and could remain intact for longer time.

Removal of metals from lead-zinc mine tailings using bioleaching and followed by sulfide precipitation.

Science.gov (United States)

Ye, Maoyou; Li, Guojian; Yan, Pingfang; Ren, Jie; Zheng, Li; Han, Dajian; Sun, Shuiyu; Huang, Shaosong; Zhong, Yujian

2017-10-01

Mine tailings often contain significant amounts of metals and sulfide, many traditional operations used to minerals was not as good as those currently available. This study investigated metals removal from lead-zinc mine tailings using bioleaching and followed by sulfide precipitation. Metals were dissolved from the tailings by the bacteria in a bioleaching reactor. During a 10% pulp density bioleaching experiment, approximately 0.82% Pb, 97.38% Zn, and 71.37% Fe were extracted after 50 days. With the pulp density of 10% and 20%, the dissolution of metals followed shrinking core kinetic model. Metals (Pb, Zn, and Fe) present in the pregnant bioleaching leachate. Metals were next precipitated as a sulfide phase using sodium sulfide (Na 2 S). Metal precipitations were selectively and quantitatively produced from the bioleaching leachate by adding Na 2 S. More than 99% of the zinc and 75% of the iron was precipitated using 25 g/L Na 2 S in the bioleaching leachate. The results in the study were to provide useful information for recovering or removing metals from lead-zinc mine tailings. Copyright © 2017 Elsevier Ltd. All rights reserved.

EVALUATION OF FERRIC CHLORIDE AND ALUM EFFICIENCIES IN ENHANCED COAGULATION FOR TOC REMOVAL AND RELATED RESIDUAL METAL CONCENTRATIONS

Directory of Open Access Journals (Sweden)

A. Mesdaghinia, M. T. Rafiee, F. Vaezi and A. H. Mahvi

2005-07-01

Full Text Available Although the removal of colloidal particles continues to be an important reason for using coagulation, a newer objective, the removal of natural organic matter (NOM to reduce the formation of disinfection by-products (DBPs, is growing in importance. Enhanced coagulation is thus introduced to most water utilities treating surface water. Bench-scale experiments were conducted to compare the effectiveness of alum and ferric chloride in removing DBPs precursors from eight synthetic water samples, each representing a different element of the USEPA’s 3×3 enhanced coagulation matrix. The effect of enhanced coagulation on the residual metal (aluminum/iron concentration in the treated water was assessed as well. The removal of total organic carbon (TOC was dependent on the coagulant type and was enhanced with increasing coagulant dose, but the latter had no further considerable effect in case of increasing to high levels. For all the treated samples coagulation with ferric chloride proved to be more effective than alum at similar doses and the mean values of treatment efficiencies were 51% and 32% for ferric chloride and alum, respectively. Ferric chloride was therefore considered the better chemical for enhancing the coagulation process. Besides, due to less production of sludge by this coagulant, it would be predicted that treatment plants would be confronted to fewer problems with respect to final sludge disposal. Measurements of residual metal in treated water indicated that iron and aluminum concentrations had been increased as expected but the quality of water concerning the residual metal deteriorated much more in cases of under-dosing. Despite expecting high residual Al and Fe concentrations under enhanced coagulation, metal concentrations were frequently remained low and were not increased appreciably.

Removal of trace metal contaminants from potable water by electrocoagulation

Science.gov (United States)

Heffron, Joe; Marhefke, Matt; Mayer, Brooke K.

2016-06-01

This study investigated the effects of four operational and environmental variables on the removal of trace metal contaminants from drinking water by electrocoagulation (EC). Removal efficiencies for five metals (arsenic, cadmium, chromium, lead and nickel) were compared under varying combinations of electrode material, post-treatment, water composition and pH. Iron electrodes out-performed aluminum electrodes in removing chromium and arsenic. At pH 6.5, aluminum electrodes were slightly more effective at removing nickel and cadmium, while at pH 8.5, iron electrodes were more effective for these metals. Regardless of electrode, cadmium and nickel removal efficiencies were higher at pH 8.5 than at pH 6.5. Post-EC treatment using membrane filtration (0.45 μm) enhanced contaminant removal for all metals but nickel. With the exception of lead, all metals exhibited poorer removal efficiencies as the ionic strength of the background electrolyte increased, particularly in the very high-solids synthetic groundwaters. Residual aluminum concentrations were lowest at pH 6.5, while iron residuals were lowest in low ionic strength waters. Both aluminum and iron residuals required post-treatment filtration to meet drinking water standards. EC with post-treatment filtration appears to effectively remove trace metal contaminants to potable water standards, but both reactor and source water parameters critically impact removal efficiency.

Chelating agent-assisted electrokinetic removal of cadmium, lead and copper from contaminated soils

International Nuclear Information System (INIS)

Giannis, Apostolos; Nikolaou, Aris; Pentari, Despina; Gidarakos, Evangelos

2009-01-01

An integrated experimental program was conducted to remove Cd, Pb and Cu from contaminated soil. The chelate agents nitrilotriacetic acid (NTA), diethylenetriamine pentaacetic acid (DTPA) and ethyleneglycol tetraacetic acid (EGTA) were used as washing solutions under different pH conditions and concentrations. Results showed that the extraction efficiency for Cd in decreasing order was NTA > EGTA > DTPA, while for Pb and Cu it was DTPA > NTA > EGTA. The use of higher chelate concentrations did not necessarily result in greater extraction efficiency. Electrokinetic remediation was applied by conditioning anolyte-catholyte pH to neutral values in order to avoid any potential alterations to the physicochemical soil properties. The removal efficiency for Cd was 65-95%, for Cu 15-60%, but for Pb was less than 20%. The phytotoxicity of the treated soil showed that the soil samples from the anode section were less phytotoxic than the untreated soil, but the phytotoxicity was increased in the samples from the cathode section. - Cadmium, lead and copper were extracted from contaminated soil by integrated electrokinetic and soil washing studies.

Chelating agent-assisted electrokinetic removal of cadmium, lead and copper from contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Giannis, Apostolos, E-mail: apostolos.giannis@enveng.tuc.g [Laboratory of Toxic and Hazardous Waste Management, Department of Environmental Engineering, Technical University of Crete, Politechnioupolis, Chania 73100 (Greece); Nikolaou, Aris [Laboratory of Toxic and Hazardous Waste Management, Department of Environmental Engineering, Technical University of Crete, Politechnioupolis, Chania 73100 (Greece); Pentari, Despina [Laboratory of Inorganic and Organic Geochemistry and Organic Petrography, Department of Mineral Resources Engineering, Technical University of Crete, Politechnioupolis, Chania 73100 (Greece); Gidarakos, Evangelos, E-mail: gidarako@mred.tuc.g [Laboratory of Toxic and Hazardous Waste Management, Department of Environmental Engineering, Technical University of Crete, Politechnioupolis, Chania 73100 (Greece)

2009-12-15

An integrated experimental program was conducted to remove Cd, Pb and Cu from contaminated soil. The chelate agents nitrilotriacetic acid (NTA), diethylenetriamine pentaacetic acid (DTPA) and ethyleneglycol tetraacetic acid (EGTA) were used as washing solutions under different pH conditions and concentrations. Results showed that the extraction efficiency for Cd in decreasing order was NTA > EGTA > DTPA, while for Pb and Cu it was DTPA > NTA > EGTA. The use of higher chelate concentrations did not necessarily result in greater extraction efficiency. Electrokinetic remediation was applied by conditioning anolyte-catholyte pH to neutral values in order to avoid any potential alterations to the physicochemical soil properties. The removal efficiency for Cd was 65-95%, for Cu 15-60%, but for Pb was less than 20%. The phytotoxicity of the treated soil showed that the soil samples from the anode section were less phytotoxic than the untreated soil, but the phytotoxicity was increased in the samples from the cathode section. - Cadmium, lead and copper were extracted from contaminated soil by integrated electrokinetic and soil washing studies.

Chelant-aided enhancement of lead mobilization in residential soils

International Nuclear Information System (INIS)

Sarkar, Dibyendu; Andra, Syam S.; Saminathan, Sumathi K.M.; Datta, Rupali

2008-01-01

Chelation of metals is an important factor in enhancing solubility and hence, availability to plants to promote phytoremediation. We compared the effects of two chelants, namely, ethylenediaminetetraacetic acid (EDTA) and ethylenediaminedisuccinic acid (EDDS) in enhancing mobilized lead (Pb) in Pb-based paint contaminated residential soils collected from San Antonio, Texas and Baltimore, Maryland. Batch incubation studies were performed to investigate the effectiveness of the two chelants in enhancing mobilized Pb, at various concentrations and treatment durations. Over a period of 1 month, the mobilized Pb pool in the San Antonio study soils increased from 52 mg kg -1 to 287 and 114 mg kg -1 in the presence of 15 mM kg -1 EDTA and EDDS, respectively. Stepwise linear regression analysis demonstrated that pH and organic matter content significantly affected the mobilized Pb fraction. The regression models explained a large percentage, from 83 to 99%, of the total variation in mobilized Pb concentrations. - Complexation by a biodegradable chelating agent, EDDS enhances mobilized Pb concentrations in Pb-paint contaminated residential soils

Enhancement of sludge reduction and methane production by removing extracellular polymeric substances from waste activated sludge.

Science.gov (United States)

Nguyen, Minh Tuan; Mohd Yasin, Nazlina Haiza; Miyazaki, Toshiki; Maeda, Toshinari

2014-12-01

The management of waste activated sludge (WAS) recycling is a concern that affects the development of the future low-carbon society, particularly sludge reduction and biomass utilization. In this study, we investigated the effect of removing extracellular polymeric substances (EPS), which play important roles in the adhesion and flocculation of WAS, on increased sludge disintegration, thereby enhancing sludge reduction and methane production by anaerobic digestion. EPS removal from WAS by ethylenediaminetetraacetic acid (EDTA) significantly enhanced sludge reduction, i.e., 49 ± 5% compared with 27 ± 1% of the control at the end the digestion process. Methane production was also improved in WAS without EPS by 8881 ± 109 CH4 μmol g(-1) dry-weight of sludge. Microbial activity was determined by denaturing gradient gel electrophoresis and real-time polymerase chain reaction, which showed that the hydrolysis and acetogenesis stages were enhanced by pretreatment with 2% EDTA, with a larger methanogenic community and better methane production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Treatment of highway runoff : engineered filter media for pollutant removal through enhanced sorption : final report.

Science.gov (United States)

2015-07-27

The work performed in this study focused on the investigation of the use of engineered biofiltration layers to enhance the removal of roadway stormwater runoff contaminants (specifically nutrients, solids, heavy metals, and pH). Six Georgia native gr...

Using Volcanic Ash to Remove Dissolved Uranium and Lead

Science.gov (United States)

McKay, David S.; Cuero, Raul G.

2009-01-01

Experiments have shown that significant fractions of uranium, lead, and possibly other toxic and/or radioactive substances can be removed from an aqueous solution by simply exposing the solution, at ambient temperature, to a treatment medium that includes weathered volcanic ash from Pu'u Nene, which is a cinder cone on the Island of Hawaii. Heretofore, this specific volcanic ash has been used for an entirely different purpose: simulating the spectral properties of Martian soil. The treatment medium can consist of the volcanic ash alone or in combination with chitosan, which is a natural polymer that can be produced from seafood waste or easily extracted from fungi, some bacteria, and some algae. The medium is harmless to plants and animals and, because of the abundance and natural origin of its ingredient( s), is inexpensive. The medium can be used in a variety of ways and settings: it can be incorporated into water-filtration systems; placed in contact or mixed with water-containing solids (e.g., soils and sludges); immersed in bodies of water (e.g., reservoirs, lakes, rivers, or wells); or placed in and around nuclear power plants, mines, and farm fields.

A Novel Approach for the Removal of Lead(II Ion from Wastewater Using Mucilaginous Leaves of Diceriocaryum eriocarpum Plant

Directory of Open Access Journals (Sweden)

Joshua N. Edokpayi

2015-10-01

Full Text Available Lead(II ion is a very toxic element known to cause detrimental effects to human health even at very low concentrations. An adsorbent prepared using mucilaginous leaves from Diceriocaryum eriocarpum plant (DEP was used for the adsorption of lead(II ion from aqueous solution. Batch experiments were performed on simulated aqueous solutions under optimized conditions of adsorbent dosage, contact time, pH and initial lead(II ion concentration at 298 K. The Langmuir isotherm model more suitably described the adsorption process than the Freundlich model with linearized coefficients of 0.9661 and 0.9547, respectively. Pseudo-second order kinetic equation best described the kinetics of the reaction. Fourier transform infra-red analysis confirmed the presence of amino (–NH, carbonyl (–C=O and hydroxyl (–OH functional groups. Application of the prepared adsorbent to wastewater samples of 10 mg/L and 12 mg/L of lead(II ion concentration taken from a waste stabilization pond showed removal efficiencies of 95.8% and 96.4%, respectively. Futhermore, 0.1 M HCl was a better desorbing agent than 0.1 M NaOH and de-ionized water. The experimental data obtained demonstrated that mucilaginous leaves from DEP can be used as a suitable adsorbent for lead(II ion removal from wastewater.

Lessons from the removal of lead from gasoline for controlling other environmental pollutants: A case study from New Zealand

Directory of Open Access Journals (Sweden)

Horrocks John

2008-01-01

Full Text Available Abstract Background It took over two decades to achieve the removal of leaded gasoline in this country. This was despite international evidence and original research conducted in New Zealand on the harm to child cognitive function and behaviour from lead exposure. Objective To identify lessons from the New Zealand experience of removing leaded gasoline that are potentially relevant to the control of other environmental pollutants. Discussion From the available documentation, we suggest a number of reasons for the slow policy response to the leaded gasoline hazard. These include: (1 industry power in the form of successful lobbying by the lead additive supplier, Associated Octel; (2 the absence of the precautionary principle as part of risk management policy; and (3 weak policymaking machinery that included: (a the poor use of health research evidence (from both NZ and internationally, as well as limited use of expertise in academic and non-governmental organisations; (b lack of personnel competent in addressing technically complex issues; and (c diffusion of responsibility among government agencies. Conclusion There is a need for a stronger precautionary approach by policymakers when considering environmental pollutants. Politicians, officials and health workers need to strengthen policymaking processes and effectively counter the industry tactics used to delay regulatory responses.

Lessons from the removal of lead from gasoline for controlling other environmental pollutants: a case study from New Zealand.

Science.gov (United States)

Wilson, Nick; Horrocks, John

2008-01-07

It took over two decades to achieve the removal of leaded gasoline in this country. This was despite international evidence and original research conducted in New Zealand on the harm to child cognitive function and behaviour from lead exposure. To identify lessons from the New Zealand experience of removing leaded gasoline that are potentially relevant to the control of other environmental pollutants. From the available documentation, we suggest a number of reasons for the slow policy response to the leaded gasoline hazard. These include: (1) industry power in the form of successful lobbying by the lead additive supplier, Associated Octel; (2) the absence of the precautionary principle as part of risk management policy; and (3) weak policymaking machinery that included: (a) the poor use of health research evidence (from both NZ and internationally), as well as limited use of expertise in academic and non-governmental organisations; (b) lack of personnel competent in addressing technically complex issues; and (c) diffusion of responsibility among government agencies. There is a need for a stronger precautionary approach by policymakers when considering environmental pollutants. Politicians, officials and health workers need to strengthen policymaking processes and effectively counter the industry tactics used to delay regulatory responses.

Enhanced xylene removal by photocatalytic oxidation using fiber-illuminated honeycomb reactor at ppb level.

Science.gov (United States)

Wu, Yi-Ting; Yu, Yi-Hui; Nguyen, Van-Huy; Lu, Kung-Te; Wu, Jeffrey Chi-Sheng; Chang, Luh-Maan; Kuo, Chi-Wen

2013-11-15

The removal of volatile organic compounds (VOCs) at ppb level is one of the most critical challenges in clean rooms for the semiconductor industry. Photocatalytic oxidation is an innovative and promising technology for ppb-level VOCs degradation. We have designed a fiber-illuminated honeycomb reactor (FIHR) in which the removal efficiency of m-xylene is significantly enhanced to 96.5% as compared to 22.0% for UV irradiation only. The results indicate that photocatalysts not only play the role to substantially oxidize m-xylene, but also alter the chemical properties of xylene under UV illumination. Using the FIHR with Mn-TiO2 photocatalyst not only increased the m-xylene removal efficiency, but also increased the CO2 selectivity. Interestingly, Mn-TiO2 in FIHR also showed a very good reusability, 93% removal efficiency was still achieved in 72-h in reaction. Thus, the FIHR gave very high removal efficiency for xylene at ppb level under room temperature. The FIHR has great potential application in the clean room for the air purification system in the future. Copyright © 2013 Elsevier B.V. All rights reserved.

Enhanced pharmaceutical removal from water in a three step bio-ozone-bio process.

Science.gov (United States)

de Wilt, Arnoud; van Gijn, Koen; Verhoek, Tom; Vergnes, Amber; Hoek, Mirit; Rijnaarts, Huub; Langenhoff, Alette

2018-07-01

Individual treatment processes like biological treatment or ozonation have their limitations for the removal of pharmaceuticals from secondary clarified effluents with high organic matter concentrations (i.e. 17 mg TOC/L). These limitations can be overcome by combining these two processes for a cost-effective pharmaceutical removal. A three-step biological-ozone-biological (BO 3 B) treatment process was therefore designed for the enhanced pharmaceutical removal from wastewater effluent. The first biological step removed 38% of ozone scavenging TOC, thus proportionally reducing the absolute ozone input for the subsequent ozonation. Complementariness between biological and ozone treatment, i.e. targeting different pharmaceuticals, resulted in cost-effective pharmaceutical removal by the overall BO 3 B process. At a low ozone dose of 0.2 g O 3 /g TOC and an HRT of 1.46 h in the biological reactors, the removal of 8 out of 9 pharmaceuticals exceeded 85%, except for metoprolol (60%). Testing various ozone doses and HRTs revealed that pharmaceuticals were ineffectively removed at 0.1 g O3/g TOC and an HRT of 0.3 h. At HRTs of 0.47 and 1.46 h easily and moderately biodegradable pharmaceuticals such as caffeine, gemfibrozil, ibuprofen, naproxen and sulfamethoxazole were over 95% removed by biological treatment. The biorecalcitrant carbamazepine was completely ozonated at a dose of 0.4 g O 3 /g TOC. Ozonation products are likely biodegraded in the last biological reactor as a 17% TOC removal was found. No appreciable acute toxicity towards D. magna, P. subcapitata and V. fischeri was found after exposure to the influents and effluents of the individual BO 3 B reactors. The BO 3 B process is estimated to increase the yearly wastewater treatment tariff per population equivalent in the Netherlands by less than 10%. Overall, the BO 3 B process is a cost-effective treatment process for the removal of pharmaceuticals from secondary clarified effluents. Copyright

A metabolic model for members of the genus Tetrasphaera involved in enhanced biological phosphorus removal

DEFF Research Database (Denmark)

Kristiansen, Rikke; Nguyen, Hien Thi Thu; Saunders, Aaron Marc

2013-01-01

Members of the genus Tetrasphaera are considered to be putative polyphosphate accumulating organisms (PAOs) in enhanced biological phosphorus removal (EBPR) from wastewater. Although abundant in Danish full-scale wastewater EBPR plants, how similar their ecophysiology is to ‘Candidatus Accumuliba......Members of the genus Tetrasphaera are considered to be putative polyphosphate accumulating organisms (PAOs) in enhanced biological phosphorus removal (EBPR) from wastewater. Although abundant in Danish full-scale wastewater EBPR plants, how similar their ecophysiology is to ‘Candidatus....... japonica and T. elongata. Based on the models, we propose that under anaerobic conditions the Tetrasphaerarelated PAOs take up glucose and ferment this to succinate and other components. They also synthesize glycogen as a storage polymer, using energy generated from the degradation of stored polyphosphate...... by ‘Candidatus Accumulibacter phosphatis’, and reveals Tetrasphaera populations to be unusual and physiologically versatile PAOs carrying out denitrification, fermentation and polyphosphate accumulation....

Removal of heavy metals from contaminated soil by electrodialytic remediation enhanced with organic acids.

Science.gov (United States)

Merdoud, Ouarda; Cameselle, Claudio; Boulakradeche, Mohamed Oualid; Akretche, Djamal Eddine

2016-11-09

The soil from an industrial area in Algeria was contaminated with Cr (8370 mg kg -1 ), Ni (1135 mg kg -1 ) and zinc (1200 mg kg -1 ). The electrodialytic remediation of this soil was studied using citric acid and EDTA as facilitating agents. 0.1 M citric acid or EDTA was added directly to the soil before it was introduced in an electrodialytic cell in an attempt to enhance the heavy metal solubility in the interstitial fluid. The more acidic pH in the soil when citric acid was used as the facilitating agent was not enough to mobilize and remove the metals from the soil. Only 7.2% of Ni and 6.7% of Zn were removed from the soil in the test with citric acid. The best results were found with EDTA, which was able to solubilize and complex Zn and Ni forming negatively charged complexes that were transported and accumulated in the anolyte. Complete removal was observed for Ni and Zn in the electrodialytic treatment with EDTA. Minor amounts of Cr were removed with both EDTA and citric acid.

Enhanced electrokinetic remediation of lead-contaminated soil by complexing agents and approaching anodes.

Science.gov (United States)

Zhang, Tao; Zou, Hua; Ji, Minhui; Li, Xiaolin; Li, Liqiao; Tang, Tang

2014-02-01

Optimizing process parameters that affect the remediation time and power consumption can improve the treatment efficiency of the electrokinetic remediation as well as determine the cost of a remediation action. Lab-scale electrokinetic remediation of Pb-contaminated soils was investigated for the effect of complexant ethylenediaminetetraacetic acid (EDTA) and acetic acid and approaching anode on the removal efficiency of Pb. When EDTA was added to the catholyte, EDTA dissolved insoluble Pb in soils to form soluble Pb-EDTA complexes, increasing Pb mobility and accordingly removal efficiency. The removal efficiency was enhanced from 47.8 to 61.5 % when the EDTA concentration was increased from 0.1 to 0.2 M, showing that EDTA played an important role in remediation. And the migration rate of Pb was increased to 72.3 % when both EDTA and acetic acid were used in the catholyte. The "approaching anode electrokinetic remediation" process in the presence of both EDTA and acetic acid had a higher Pb-removal efficiency with an average efficiency of 83.8 %. The efficiency of electrokinetic remediation was closely related to Pb speciation. Exchangeable and carbonate-bounded Pb were likely the forms which could be removed. All results indicate that the approaching anode method in the presence of EDTA and acetic acid is an advisable choice for electrokinetic remediation of Pb-contaminated soil.

The potential of the innovative SeMPAC process for enhancing the removal of recalcitrant organic micropollutants

Energy Technology Data Exchange (ETDEWEB)

Alvarino, T., E-mail: teresa.alvarino@usc.es [Department of Chemical Engineering, Institute of Technology, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain); Komesli, O. [Ataturk University, Department of Environmental Engineering, 25250 Erzurum (Turkey); Middle East Technical University, Department of Environmental Engineering, 06531 Ankara (Turkey); Suarez, S., E-mail: sonia.suarez@usc.es [Department of Chemical Engineering, Institute of Technology, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain); Lema, J.M., E-mail: juan.lema@usc.es [Department of Chemical Engineering, Institute of Technology, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain); Omil, F., E-mail: francisco.omil@usc.es [Department of Chemical Engineering, Institute of Technology, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain)

2016-05-05

Highlights: • Complete OMPs mass balance in a combined system biological treatment plus PAC. • Improvement of the denitrification after PAC addition. • Enhancement of OMPs biotransformation after PAC addition. • Relation between hydrophobicity (log D) and sorption onto the PAC. • Progressive saturation of the activated carbon in the solid phase with the time. - Abstract: SeMPAC is an innovative process based on a membrane sequential batch reactor to which powdered activated carbon (PAC) is directly added. It was developed with the aim of obtaining a high quality effluent in terms of conventional pollutants and organic micropollutants (OMPs). High COD removal and nitrification efficiencies (>95%) were obtained already during the operation without PAC, although denitrification was enhanced by PAC addition. OMPs were followed in the solid and liquid matrixes so that biotransformation, sorption onto the sludge and adsorption onto the PAC could be assessed. Recalcitrant compounds, such as carbamazepine and diazepam, were readily removed only after PAC addition (>99%). Progressive saturation of PAC was observed, with increasing concentrations of OMPs in the solid phase. Removal efficiencies for recalcitrant compounds were used as indicators for new additions of PAC. An improvement in the moderately biodegradable OMPs removal was observed after PAC addition (e.g. fluoxetine, trimethoprim) which was attributed to the biofilm that grew onto the sorbent, as well as to adsorption onto PAC.

Experimental Design of Electrocoagulation and Magnetic Technology for Enhancing Suspended Solids Removal from Synthetic Wastewater

Directory of Open Access Journals (Sweden)

Moh Faiqun Ni'am

2014-10-01

Full Text Available Design of experiments (DOE is one of the statistical method that is used as a tool to enhance and improve experimental quality. The changes to the variables of a process or system is supposed to give the optimal result (response and quite satisfactory. Experimental design can defined as a test or series of test series by varying the input variables (factors of a process that can known to cause changes in output (response. This paper presents the results of experimental design of wastewater treatment by electrocoagulation (EC technique. A combined magnet and electrocoagulation (EC technology were designed to increase settling velocity and to enhance suspended solid removal efficiencies from wastewater samples. In this experiment, a synthetic wastewater samples were prepared by mixing 700 mg of the milk powder in one litre of water and treated by using an acidic buffer solution. The monopolar iron (Fe plate anodes and cathodes were employed as electrodes. Direct current was varied in a range of between 0.5 and 1.1 A, and flowrate in a range of between 1.00 to 3.50 mL/s. One permanent magnets namely AlNiCo with a magnetic strength of 0.16T was used in this experiment. The results show that the magnetic field and the flowrate have major influences on suspended solids removal. The efficiency removals of suspended solids, turbidity and COD removal efficiencies at optimum conditions were found to be more than 85%, 95%, and 75%, respectively.

Photochemical removal of aniline in aqueous solutions: switching from photocatalytic degradation to photo-enhanced polymerization recovery.

Science.gov (United States)

Tang, Heqing; Li, Jing; Bie, Yeqiang; Zhu, Lihua; Zou, Jing

2010-03-15

Organic pollutants may be treated by either a degradation process or a recovery process in the view point of sustainable chemistry. Photocatalytic removal of aniline was investigated in aqueous solutions. It was found that the photocatalytic oxidation of aniline resulted in its degradation or polymerization, depending on its concentration. Hence a new treatment strategy was proposed in combination of photocatalytic degradation and polymerization, where the polymerization was in fact a recovery process. When aniline concentration was as low as 0.1 mmol L(-1), it was possible to photocatalytically degrade aniline, which could be further enhanced by increasing solution pH, modifying TiO(2) surface with the addition of anions, or coupling with the photoreduction of added oxidants. When aniline concentration was increased to about 1 mmol L(-1), the photocatalytic oxidation was observed to yield the polymerization of aniline, leading to nanocomposites of polyaniline (PAN) and TiO(2). Alternatively, the photo-enhanced chemical polymerization of aniline at higher concentrations (>or=50 mmol L(-1)) in the presence of chemical oxidants produced PAN nanostructures. The conversion of pollutant aniline to valuable PAN nanostructures or nano-PAN/TiO(2) composites is suggestive for possible applications in the treatment of aniline wastewaters as a sustainable environmental protection measure. (c) 2009 Elsevier B.V. All rights reserved.

Use of additives to enhance the removal of phenols from water treated with horseradish and hydrogen peroxide.

Science.gov (United States)

Tonegawa, Masami; Dec, Jerzy; Bollag, Jean-Marc

2003-01-01

Use of additives, such as polyethylene glycol (PEG), selected surfactants, chitosan gel, or activated carbon, has been shown to enhance enzymatic treatment of water polluted with organic compounds. In this study, additives were used to facilitate the removal of 2,4-dichlorophenol (2,4-DCP) from water using minced horseradish (Armoracia rusticana P. Gaertn. et al.) as a carrier of peroxidase activity. The specific objectives of the study were to (i) enhance the pollutant removal activity of minced horseradish by the addition of PEG and other additives (e.g., Tween 20, Triton X-100, and rhamnolipid); (ii) eliminate colored reaction products by the addition of chitosan; and (iii) eliminate color by amending treated water with activated carbon. The disappearance of 2,4-DCP in horseradish-treated water samples amended with PEG or various surfactants (75-90%) was greatly increased over that observed in nonamended samples (29%). The effect of PEG depended on its average molecular weight. As indicated by visible spectrophotometry, enclosing horseradish pieces between two sealed chitosan films completely eliminated colored reaction products; however, the decolorization was accompanied by a reduction in 2,4-DCP removal (from 95 to 60%). On the other hand, commercially available activated carbon completely removed colored reaction products from the treated water without reducing the removal efficiency. Based on the results obtained, it can be concluded that the use of additives may considerably improve the quality of wastewater treated by plant materials.

New mechanism for enhancing ash removal efficiency and reducing tritium inventory

International Nuclear Information System (INIS)

Li Chengyue; Deng Baiquan; Yan Jiancheng

2007-01-01

A new mechanism is suggested to suppress ash particle back streams in the divertor region of our fusion experimental breeder (FEB) reactor for enhancing the ash removal efficiency and reducing the tritium inventory by applications of the nonlinear effect of high power rf ponderomotive force potential which reflects the plate-released and re-ionized He + back to the plate. Meanwhile, the potential does not hinder α particles, which are coming from scraping of the layer, flowing to the target plate. However, it does stop tritium ions flowing to the target. Based on the FEB design parameters, our calculations have shown that the ash removal efficiency can be improved by as much as 40% if the parallel component of rf field 150-200 V/cm is applied to the location at a perpendicular distance L=20 cm apart from the plate and the plate-recycling neutral helium atom energy is about 0.75 eV, at the same time, the tritium inventory can be reduced to some extent. (authors)

Washing enhanced electrokinetic remediation for removal cadmium from real contaminated soil

International Nuclear Information System (INIS)

Giannis, Apostolos; Gidarakos, Evangelos

2005-01-01

The main objective of this study is to evaluate the combination of electrokinetic remediation and soil washing technology in order to remove cadmium from contaminated soil. This paper presents the results of an experimental research undertaken to evaluate different washing and purging solutions to enhance the removal of cadmium from a real contaminated soil during electrokinetic remediation. Two different experimental modules were applied in the laboratory. Soil was saturated with tap water, while acetic and hydrochloric acids, as well as ethylenediaminetetraacetic acid (EDTA) were used as purging solutions in the first module. Results show that there was a decrease of cadmium concentration near anode, but a significant increase in the middle of the cell, due to the increasing pH. Citric, nitric and acetic acids were used for soil washing and purging solutions in the second module. In this case, an 85% reduction of cadmium concentration was achieved. Therefore, results indicate that soil pH and washing solutions are the most important factors in governing the dissolution and/or desorption of Cd in a soil system under electrical fields

Removal of Lead from Wastewater Contaminated with Chemical Synthetic Dye by Aspergillus terreus

Directory of Open Access Journals (Sweden)

Lamyai Neeratanaphan

2015-07-01

Full Text Available Novel isolated microorganisms have been demonstrated to efficiently remove lead from wastewater contaminated with chemical synthetic dye. In this study, the physical and chemical parameters of wastewater samples (including Pb concentrations were analyzed before and after treatment with microorganisms. The highest Pb concentration detected in wastewater was 0.788 mg/l. Investigations of the Pb tolerance and removal capacities of microorganism strains isolated from the wastewater sediment resulted in the selection of three fungal isolates (F102, F203 and F302. Interestingly, isolate F203 had a Pb tolerance of up to 100 mg/l. Using DNA barcoding and morphological characteristics, fungal isolate F203 was identified as Aspergillus terreus. Wastewater characteristics before treatment included a grayish black color with pH, TDS, BOD, COD and Pb concentrations higher than the Thailand standard values. Wastewater qualities after treatment with A. terreus showed definite improvement; however, the values of certain parameters were still higher than the allowed values based on the Thailand standard. The only improvement that fell within the allowed standard was the Pb concentration. Next, A. terreus was used for Pb adsorption in wastewater with an initial Pb concentration of 0.788 mg/l at time points corresponding to 0, 24, 48, 72, 96, 120, 144 and 168 h of incubation. The results showed that A. terreus could adsorb and remove higher amounts of Pb from wastewater than the other fungal isolates. Time course adsorption analysis showed the remaining Pb concentrations as 0.788, 0.213, 0.162, 0.117, 0.100, 0.066, 0.042 and 0.032 mg/l, respectively; the percentage of Pb removal could be estimated as 0, 72.97, 79.44, 85.15, 87.31, 91.62, 94.67 and 95.94%, respectively. In conclusion, A. terreus possessed the ability to adsorb up to 96% of Pb from chemical synthetic dye within 168 h. Thus, A. terreus might be suitable for adaptation and use in Pb treatment.

[Kinetic simulation of enhanced biological phosphorus removal with fermentation broth as carbon source].

Science.gov (United States)

Zhang, Chao; Chen, Yin-Guang

2013-07-01

As a high-quality carbon source, fermentation broth could promote the phosphorus removal efficiency in enhanced biological phosphorus removal (EBPR). The transformation of substrates in EBPR fed with fermentation broth was well simulated using the modified activated sludge model No. 2 (ASM2) based on the carbon source metabolism. When fermentation broth was used as the sole carbon source, it was found that heterotrophic bacteria acted as a promoter rather than a competitor to the phosphorus accumulating organisms (PAO). When fermentation broth was used as a supplementary carbon source of real municipal wastewater, the wastewater composition was optimized for PAO growth; and the PAO concentration, which was increased by 3.3 times compared to that in EBPR fed with solely real municipal wastewater, accounting for about 40% of the total biomass in the reactor.

Overexpression of histone demethylase Fbxl10 leads to enhanced migration in mouse embryonic fibroblasts

Energy Technology Data Exchange (ETDEWEB)

Rohde, Magdalena; Sievers, Elisabeth; Janzer, Andreas [Institute of Pathology, University of Bonn, Sigmund-Freud-Strasse 25, 53127 Bonn (Germany); Willmann, Dominica [Urologische Klinik/Frauenklinik und Zentrale Klinische Forschung, Klinikum der Universität Freiburg, Breisacherstrasse 66, 79106 Freiburg (Germany); Egert, Angela; Schorle, Hubert [Department of Developmental Pathology, Institute of Pathology, University of Bonn, Sigmund-Freud-Strasse 25, 53127 Bonn (Germany); Schüle, Roland [Urologische Klinik/Frauenklinik und Zentrale Klinische Forschung, Klinikum der Universität Freiburg, Breisacherstrasse 66, 79106 Freiburg (Germany); Kirfel, Jutta, E-mail: Jutta.Kirfel@ukb.uni-bonn.de [Institute of Pathology, University of Bonn, Sigmund-Freud-Strasse 25, 53127 Bonn (Germany)

2016-11-01

Cell migration is a central process in the development and maintenance of multicellular organisms. Tissue formation during embryonic development, wound healing, immune responses and invasive tumors all require the orchestrated movement of cells to specific locations. Histone demethylase proteins alter transcription by regulating the chromatin state at specific gene loci. FBXL10 is a conserved and ubiquitously expressed member of the JmjC domain-containing histone demethylase family and is implicated in the demethylation of H3K4me3 and H3K36me2 and thereby removing active chromatin marks. However, the physiological role of FBXL10 in vivo remains largely unknown. Therefore, we established an inducible gain of function model to analyze the role of Fbxl10 and compared wild-type with Fbxl10 overexpressing mouse embryonic fibroblasts (MEFs). Our study shows that overexpression of Fbxl10 in MEFs doesn’t influence the proliferation capability but leads to an enhanced migration capacity in comparison to wild-type MEFs. Transcriptome and ChIP-seq experiments demonstrated that Fbxl10 binds to genes involved in migration like Areg, Mdk, Lmnb1, Thbs1, Mgp and Cxcl12. Taken together, our results strongly suggest that Fbxl10 plays a critical role in migration by binding to the promoter region of migration-associated genes and thereby might influences cell behaviour to a possibly more aggressive phenotype. - Highlights: • Migration capability of MEFs is enhanced after Fbxl10 upregulation. • Overexpression of Fbxl10 induced migration-associated genes. • Fbxl10 binds directly to migration-associated genes.

Overexpression of histone demethylase Fbxl10 leads to enhanced migration in mouse embryonic fibroblasts

International Nuclear Information System (INIS)

Rohde, Magdalena; Sievers, Elisabeth; Janzer, Andreas; Willmann, Dominica; Egert, Angela; Schorle, Hubert; Schüle, Roland; Kirfel, Jutta

2016-01-01

Cell migration is a central process in the development and maintenance of multicellular organisms. Tissue formation during embryonic development, wound healing, immune responses and invasive tumors all require the orchestrated movement of cells to specific locations. Histone demethylase proteins alter transcription by regulating the chromatin state at specific gene loci. FBXL10 is a conserved and ubiquitously expressed member of the JmjC domain-containing histone demethylase family and is implicated in the demethylation of H3K4me3 and H3K36me2 and thereby removing active chromatin marks. However, the physiological role of FBXL10 in vivo remains largely unknown. Therefore, we established an inducible gain of function model to analyze the role of Fbxl10 and compared wild-type with Fbxl10 overexpressing mouse embryonic fibroblasts (MEFs). Our study shows that overexpression of Fbxl10 in MEFs doesn’t influence the proliferation capability but leads to an enhanced migration capacity in comparison to wild-type MEFs. Transcriptome and ChIP-seq experiments demonstrated that Fbxl10 binds to genes involved in migration like Areg, Mdk, Lmnb1, Thbs1, Mgp and Cxcl12. Taken together, our results strongly suggest that Fbxl10 plays a critical role in migration by binding to the promoter region of migration-associated genes and thereby might influences cell behaviour to a possibly more aggressive phenotype. - Highlights: • Migration capability of MEFs is enhanced after Fbxl10 upregulation. • Overexpression of Fbxl10 induced migration-associated genes. • Fbxl10 binds directly to migration-associated genes.

Single underwater image enhancement based on color cast removal and visibility restoration

Science.gov (United States)

Li, Chongyi; Guo, Jichang; Wang, Bo; Cong, Runmin; Zhang, Yan; Wang, Jian

2016-05-01

Images taken under underwater condition usually have color cast and serious loss of contrast and visibility. Degraded underwater images are inconvenient for observation and analysis. In order to address these problems, an underwater image-enhancement method is proposed. A simple yet effective underwater image color cast removal algorithm is first presented based on the optimization theory. Then, based on the minimum information loss principle and inherent relationship of medium transmission maps of three color channels in an underwater image, an effective visibility restoration algorithm is proposed to recover visibility, contrast, and natural appearance of degraded underwater images. To evaluate the performance of the proposed method, qualitative comparison, quantitative comparison, and color accuracy test are conducted. Experimental results demonstrate that the proposed method can effectively remove color cast, improve contrast and visibility, and recover natural appearance of degraded underwater images. Additionally, the proposed method is comparable to and even better than several state-of-the-art methods.

Features of an emergency heat-conducting path in reactors about lead-bismuth and lead heat-carriers

International Nuclear Information System (INIS)

Beznosov, A.V.; Bokova, T.A.; Molodtsov, A.A.

2006-01-01

The reactor emergency heat removal systems should transfer heat from the surface of reactor core fuel element claddings to the primary circuit followed by heat transfer to the environment. One suggests three design approaches for emergency heat removal systems in lead-bismuth and lead cooled reactor circuits that take account of the peculiar nature of their features. Application of the discussed systems for emergency heat removal improves safety of lead-bismuth and lead cooled reactor plants [ru

REMOVAL OF LEAD(II) IONS FROM AQUEOUS SOLUTIONS ...

African Journals Online (AJOL)

Preferred Customer

lung cancer, convulsion and even death if ingested at elevated levels. ... osmosis have been used for removing heavy metal ions from aqueous media [4-6]. ... organic molecules and silica surface functions, (ii) chlorination of the silica surface ...

Biosorption characteristic of Alcaligenes sp. BAPb.1 for removal of lead(II) from aqueous solution.

Science.gov (United States)

Jin, Yu; Yu, Sumei; Teng, Chunying; Song, Tao; Dong, Liying; Liang, Jinsong; Bai, Xin; Xu, Xiuhong; Qu, Juanjuan

2017-06-01

In this study, strain BAPb.1 was isolated from lead mining area and used as an adsorbent to remove lead(II) ions from aqueous solution. The physicochemical characteristics, heavy metal resistance and antibiotic sensitivity of strain BAPb.1 were investigated. Biosorption capacity was evaluated by batch biosorption experiments, and isothermal characteristics were discussed. Atomic force microscopy (AFM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and Fourier transform infrared spectrometry (FTIR) were conducted to explore the mechanism for lead(II) adsorption. Based on morphological and physiological characteristics as well as the phylogenetic analysis of 16S rDNA sequences, strain BAPb.1 was identified as a member of the genus Alcaligenes. It exhibited high resistances to multiple heavy metals such as lead(II), copper(II), zinc(II), nickel(II) and chromium(VI), and to antibiotics such as kanamycin, ampicillin, streptomycin, chloramphenicol, and tetracycline. The optimum conditions for maximum biosorption rate of 85.2% and maximum capacity of 56.8 mg g -1 were found at pH of 5, adsorbent dosage of 1.5 g L -1 (dry weight), initial lead(II) concentration of 100 mg L -1 , and contact time of 30 min at 30 °C. Biosorption isotherms were well fitted with Langmuir isotherm model. Mechanism analysis reveals that the lead(II) ions may exchange with sodium and potassium ions, and the hydroxyl, carbonyl and phosphate groups on the cell surface can chelate the lead(II) ions, therefore, surface adsorption play significant role in the biosorption process.

Enhanced Dispersion and Removal of Ammonia Emitted from a Poultry House with a Vegetative Environmental Buffer

Directory of Open Access Journals (Sweden)

Kyoung S. Ro

2018-03-01

Full Text Available Vegetative environmental buffers (VEBs, which are composed of tolerant trees, shrubs, and tall grasses, can be used to control and reduce the transport of ammonia (NH3 emissions from animal feeding operations (AFOs. However, the effectiveness of VEBs has not been quantitated. In this study, we measure the dispersion and removal of NH3 in simulated emissions from a small broiler house that was equipped with a VEB. The dispersion enhancement due to the VEB was estimated by comparing the measured downwind concentration of the co-released tracer gas, methane (CH4, to the theoretical CH4 concentrations at the same distance downwind without the VEB. The accuracy of the theoretical downwind concentrations calculated using the forward Lagrangian stochastic (fLS technique was 95%, which was validated by comparing the measured and calculated CH4 concentrations in a separate experiment without the VEB. The VEB enhanced the dispersion of CH4 and reduced the downwind concentration to 63% of the theoretical concentration. In addition to dispersion, the VEB removed another 22% of the NH3, resulting in a net 51% decrease of the theoretical downwind concentration. These results clearly demonstrated that the VEB was effective both in dispersing and removing NH3 emitted from the broiler house.

The microbial community in a high-temperature enhanced biological phosphorus removal (EBPR process

Directory of Open Access Journals (Sweden)

Ying Hui Ong

2016-01-01

Full Text Available An enhanced biological phosphorus removal (EBPR process operated at a relatively high temperature, 28 °C, removed 85% carbon and 99% phosphorus from wastewater over a period of two years. This study investigated its microbial community through fluorescent in situ hybridization (FISH and clone library generation. Through FISH, considerably more Candidatus “Accumulibacter phosphatis” (Accumulibacter-polyphosphate accumulating organisms (PAOs than Candidatus ‘Competibacter phosphatis’ (Competibacter-glycogen accumulating organisms were detected in the reactor, at 36 and 7% of total bacterial population, respectively. A low ratio of Glycogen/Volatile Fatty Acid of 0.69 further indicated the dominance of PAOs in the reactor. From clone library generated, 26 operational taxonomy units were retrieved from the sludge and a diverse population was shown, comprising Proteobacteria (69.6%, Actinobacteria (13.7%, Bacteroidetes (9.8%, Firmicutes (2.94%, Planctomycetes (1.96%, and Acidobacteria (1.47%. Accumulibacter are the only recognized PAOs revealed by the clone library. Both the clone library and FISH results strongly suggest that Accumulibacter are the major PAOs responsible for the phosphorus removal in this long-term EBPR at relatively high temperature.

Analysis of the passive heat removal enhancement for AP1000 containment due to the partially wetted coverage

Energy Technology Data Exchange (ETDEWEB)

Li, Cheng, E-mail: 510395453@qq.com [State Nuclear Power Technology Research & Development Center, 102209 Beijing (China); Li, Le [Tsinghua University, Institute of Nuclear and New Energy Technology, 100084 Beijing (China); Li, Junming [Tsinghua University, Key Laboratory for Thermal Science and Power Engineering of Ministry of Education, Department of Thermal Engineering, Beijing 100084 (China); Zhang, Yajun [Tsinghua University, Institute of Nuclear and New Energy Technology, 100084 Beijing (China); Li, Zhihui [State Nuclear Power Technology Research & Development Center, 102209 Beijing (China)

2017-03-15

Highlights: • Heat removal by steam condensation, thermal conduction and evaporation is the most important scheme for AP1000 PCCS. Traditionally, studies on containment wall condensation and evaporation have been widely made, while it lacks studies on the shell two-dimension (2-D) thermal conduction. Currently, based on the known heat and mass transfer correlations and the phenomenon from water wetted coverage test, the physical model for 2-D thermal conduction is given and numerical simulation is then made. By discussions, it forms the following highlights. • The partially wetted surface can enhance the whole heat transfer process (including inner condensation, wall thermal conduction and outside cooling) and the maximum enhancement factor can be as large as 63%. There is an enhancement peak at around dry strip fraction a = 90%. When L is less than 0.03 m, its influence on heat transfer is small and the enhancement is mainly affected by dry coverage. However, for larger L, both α and L contribute much to larger enhancement. • Location at the spring line is often used for safety analysis and the dry strip fraction there for AP1000 is mainly at 10%–80%. Accordingly, further analysis is made on L (0.03 < L < 0.3) and a fitting expression is given for α = 10%–80%. It could be used to improve the corresponding software and it could also be used for containment scaling-down criteria analysis. - Abstract: AP1000 containment uses the water film evaporation, coupled with containment inner condensation, to remove the core decay heat. However, water film cannot fully cover heat transfer surface and dry-wetted strips appear. As a result, heat transfer within the containment shell is a two-dimension thermal conduction. Current work numerically studied the AP1000 heat removal enhancement due to the partially wetted coverage phenomenon. It used the evaporation and condensation boundary conditions and Fluent software to calculate the local heat fluxes and their

Analysis of the passive heat removal enhancement for AP1000 containment due to the partially wetted coverage

International Nuclear Information System (INIS)

Li, Cheng; Li, Le; Li, Junming; Zhang, Yajun; Li, Zhihui

2017-01-01

Highlights: • Heat removal by steam condensation, thermal conduction and evaporation is the most important scheme for AP1000 PCCS. Traditionally, studies on containment wall condensation and evaporation have been widely made, while it lacks studies on the shell two-dimension (2-D) thermal conduction. Currently, based on the known heat and mass transfer correlations and the phenomenon from water wetted coverage test, the physical model for 2-D thermal conduction is given and numerical simulation is then made. By discussions, it forms the following highlights. • The partially wetted surface can enhance the whole heat transfer process (including inner condensation, wall thermal conduction and outside cooling) and the maximum enhancement factor can be as large as 63%. There is an enhancement peak at around dry strip fraction a = 90%. When L is less than 0.03 m, its influence on heat transfer is small and the enhancement is mainly affected by dry coverage. However, for larger L, both α and L contribute much to larger enhancement. • Location at the spring line is often used for safety analysis and the dry strip fraction there for AP1000 is mainly at 10%–80%. Accordingly, further analysis is made on L (0.03 < L < 0.3) and a fitting expression is given for α = 10%–80%. It could be used to improve the corresponding software and it could also be used for containment scaling-down criteria analysis. - Abstract: AP1000 containment uses the water film evaporation, coupled with containment inner condensation, to remove the core decay heat. However, water film cannot fully cover heat transfer surface and dry-wetted strips appear. As a result, heat transfer within the containment shell is a two-dimension thermal conduction. Current work numerically studied the AP1000 heat removal enhancement due to the partially wetted coverage phenomenon. It used the evaporation and condensation boundary conditions and Fluent software to calculate the local heat fluxes and their

Enhanced Cr(VI) removal by polyethylenimine- and phosphorus-codoped hierarchical porous carbons.

Science.gov (United States)

Chen, Shixia; Wang, Jun; Wu, Zeliang; Deng, Qiang; Tu, Wenfeng; Dai, Guiping; Zeng, Zheling; Deng, Shuguang

2018-08-01

The amino- and phosphorus-codoped (N,P-codoped) porous carbons derived from oil-tea shells were facilely fabricated through a combination of phosphoric acid (H 3 PO 4 ) activation and amino (polyethylenimine, PEI) modification method. The as-synthesized carbon adsorbents were systematically characterized and evaluated for Cr(VI) removal in aqueous solutions. The relationship between adsorbent properties and adsorption behaviors was illustrated. Moreover, the influences of contact time, initial Cr(VI) concentration, pH, coexisting anions and temperature were also investigated. The adsorption behavior of Cr(VI) could be perfectly described by the pseudo-second-order kinetic model and Sips adsorption model. The maximum adsorption capacity of Cr(VI) on the carbon adsorbents synthesized in this work was 355.0 mg/g, and this excellent Cr(VI) capacity could be sustained with other coexisting anions. In addition to high surface area and suitable pore size distribution, the high Cr(VI) removal capacity is induced by rich heteroatoms incorporation and the Cr(VI) removal mechanism was clearly illustrated. Furthermore, the continuous column breakthrough experiment on obtained N,P-codoped carbon was conducted and well fitted by the Thomas model. This work revealed that PEI modification and P-containing groups could significantly enhance Cr(VI) adsorption capacity and make these N,P-codoped biomass-derived carbons potent adsorbents in practical water treatment applications. Copyright © 2018 Elsevier Inc. All rights reserved.

Enhancement of emulsifier production by Curvularia lunata in cadmium, zinc and lead presence.

Science.gov (United States)

Paraszkiewicz, Katarzyna; Frycie, Aleksandra; Słaba, Mirosława; Długoński, Jerzy

2007-10-01

The influence of cadmium, zinc and lead on fungal emulsifier synthesis and on the growth of filamentous fungus Curvularia lunata has been studied. Tolerance to heavy metals established for C. lunata was additionally compared with the sensitivity exhibited by strains of Curvularia tuberculata and Paecilomyces marquandii-fungi which do not secrete compounds of emulsifying activity. Although C. lunata, as the only one out of all studied fungi, exhibited the lowest tolerance to heavy metals when grown on a solid medium (in conditions preventing emulsifier synthesis), it manifested the highest tolerance in liquid culture - in conditions allowing exopolymer production. Cadmium, zinc and lead presented in liquid medium up to a concentration of 15 mM had no negative effect on C. lunata growth and stimulated emulsifier synthesis. In the presence of 15 mM of heavy metals, both the emulsifier and 24-h-old growing mycelium exhibited maximum sorption capacities, which were determined as 18.2 +/- 2.67, 156.1 +/- 10.32 mg g(-1) for Cd2+, 22.2 +/- 3.40, 95.2 +/- 14.21 mg g(-1) for Zn2+ and 51.1 +/- 1.85, 230.0 +/- 28.47 mg g(-1) for Pb2+ respectively. The results obtained by us in this work indicate that the emulsifier acts as a protective compound increasing the ability of C. lunata to survive in heavy metal polluted environment. Enhancement of exopolymer synthesis in the presence of Cd2+, Zn2+ and Pb2+ may also suggest, at least to some extent, a metal-specific nature of emulsifier production in C. lunata. Due to accumulation capability and tolerance to heavy metals, C. lunata mycelium surrounded by the emulsifier could be applied for toxic metal removal.

Understanding and removing surface states limiting charge transport in TiO2 nanowire arrays for enhanced optoelectronic device performance.

Science.gov (United States)

Sheng, Xia; Chen, Liping; Xu, Tao; Zhu, Kai; Feng, Xinjian

2016-03-01

Charge transport within electrode materials plays a key role in determining the optoelectronic device performance. Aligned single-crystal TiO 2 nanowire arrays offer an ideal electron transport path and are expected to have higher electron mobility. Unfortunately, their transport is found not to be superior to that in nanoparticle films. Here we show that the low electron transport in rutile TiO 2 nanowires is mainly caused by surface traps in relatively deep energy levels, which cannot be removed by conventional approaches, such as oxygen annealing treatment. Moreover, we demonstrate an effective wet-chemistry approach to minimize these trap states, leading to over 20-fold enhancement in electron diffusion coefficient and 62% improvement in solar cell performance. On the basis of our results, the potential of TiO 2 NWs can be developed and well-utilized, which is significantly important for their practical applications.

Enhanced chitosan beads-supported Fe(0)-nanoparticles for removal of heavy metals from electroplating wastewater in permeable reactive barriers.

Science.gov (United States)

Liu, Tingyi; Yang, Xi; Wang, Zhong-Liang; Yan, Xiaoxing

2013-11-01

The removal of heavy metals from electroplating wastewater is a matter of paramount importance due to their high toxicity causing major environmental pollution problems. Nanoscale zero-valent iron (NZVI) became more effective to remove heavy metals from electroplating wastewater when enhanced chitosan (CS) beads were introduced as a support material in permeable reactive barriers (PRBs). The removal rate of Cr (VI) decreased with an increase of pH and initial Cr (VI) concentration. However, the removal rates of Cu (II), Cd (II) and Pb (II) increased with an increase of pH while decreased with an increase of their initial concentrations. The initial concentrations of heavy metals showed an effect on their removal sequence. Scanning electron microscope images showed that CS-NZVI beads enhanced by ethylene glycol diglycidyl ether (EGDE) had a loose and porous surface with a nucleus-shell structure. The pore size of the nucleus ranged from 19.2 to 138.6 μm with an average aperture size of around 58.6 μm. The shell showed a tube structure and electroplating wastewaters may reach NZVI through these tubes. X-ray photoelectron spectroscope (XPS) demonstrated that the reduction of Cr (VI) to Cr (III) was complete in less than 2 h. Cu (II) and Pb (II) were removed via predominant reduction and auxiliary adsorption. However, main adsorption and auxiliary reduction worked for the removal of Cd (II). The removal rate of total Cr, Cu (II), Cd (II) and Pb (II) from actual electroplating wastewater was 89.4%, 98.9%, 94.9% and 99.4%, respectively. The findings revealed that EGDE-CS-NZVI-beads PRBs had the capacity to remediate actual electroplating wastewater and may become an effective and promising technology for in situ remediation of heavy metals. Copyright © 2013 Elsevier Ltd. All rights reserved.

Atypical choroid plexus papilloma: spontaneous resolution of diffuse leptomeningeal contrast enhancement after primary tumor removal in 2 pediatric cases.

Science.gov (United States)

Scala, Marcello; Morana, Giovanni; Milanaccio, Claudia; Pavanello, Marco; Nozza, Paolo; Garrè, Maria Luisa

2017-09-01

Atypical choroid plexus papillomas can metastasize in the form of leptomeningeal seeding. Postoperative chemotherapy is the recommended first-line treatment when gross-total removal is not achieved or in cases of disseminated disease. Here the authors report on 2 children with atypical choroid plexus papillomas and MRI findings of diffuse leptomeningeal enhancement at diagnosis, later presenting with spontaneous resolution of the leptomeningeal involvement after removal of the primary lesions. Observations in this report expand our knowledge about the natural history and biological behavior of these tumors and highlight the role of close neuroimaging surveillance in the management of atypical choroid plexus papillomas in cases with MRI evidence of diffuse leptomeningeal enhancement at presentation.

Multifold enhanced synergistic removal of nickel and phosphate by a (N,Fe)-dual-functional bio-sorbent: Mechanism and application

International Nuclear Information System (INIS)

Zhang, Yan-hong; Liu, Fu-qiang; Zhu, Chang-qing; Zhang, Xiao-peng; Wei, Meng-meng; Wang, Feng-he; Ling, Chen; Li, Ai-min

2017-01-01

Highlights: • A (N,Fe)-dual-functional bio-sorbent was newly synthesized. • Removal of Ni(II) and H_2PO_4"− could be remarkably enhanced over 3 times. • A multiple mechanism resulted in the synergic adsorption. • N/Fe-DB is efficient and repeatable in treating electroplating wastewater. - Abstract: A novel (N,Fe)-dual-functional biosorbent (N/Fe-DB) capable of efficient synergistic removal of Ni(II) and H_2PO_4"− from aqueous solution was synthesized. The adsorption capacities of Ni(II) and H_2PO_4"− were both remarkably enhanced over 3 times compared with those in single systems. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy confirmed that complexation of amino groups and ligand exchange of hydrous ferric oxide in N/Fe-DB played dominant roles. The electric double layer compressing and chelating ligand of deprotonated H_2PO_4"− accounted for the enhanced removal of Ni(II) in binary system, while cation bridge interaction promoted uptake of H_2PO_4"−. Furthermore, the coadsorbates were sequentially recovered, with the ratios of more than 99.0%. Besides, the recovered N/Fe-DB remained stable and applicable to the treatment of real electroplating wastewater even after six adsorption-regeneration cycles. Since the electroplating industry is springing up, effective control of heavy metals and phosphate has attracted global concerns. Based on the enhanced coremoval properties and superb regenerability, N/Fe-DB is potentially applicable to practical production.

Potential of hydrolysis of particulate COD in extended anaerobic conditions to enhance biological phosphorous removal.

Science.gov (United States)

Jabari, P; Yuan, Q; Oleszkiewicz, J A

2016-11-01

The effect of anaerobic hydrolysis of particulate COD (pCOD) on biological phosphorous removal in extended anaerobic condition was investigated through (i) sequencing batch reactors (SBR)s with anaerobic hydraulic retention time (HRT) of 0.8, 2, and 4 h; (ii) batch tests using biomass from a full scale biological nutrient removal (BNR) plant; and (iii) activated sludge modeling (BioWin 4.1 simulation). The results from long-term SBRs operation showed that phosphorus removal was correlated to the ratio of filtered COD (FCOD) to total phosphorus (TP) in the influent. Under conditions with low FCOD/TP ratio (average of 20) in the influent, extending anaerobic HRT to 4 h in the presence of pCOD did not significantly improve overall phosphorous removal. During the period with high FCOD/TP ratio (average of 37) in the influent, all SBRs removed phosphorous completely, and the long anaerobic HRT did not have negative effect on overall phosphorous removal. The batch tests also showed that pCOD at different concentration during 4 h test did not affect the rate of anaerobic phosphorus release. The rate of anaerobic hydrolysis of pCOD was significantly low and extending the anaerobic HRT was ineffective. The simulation (BioWin 4.1) of SBRs with low influent FCOD/TP ratio showed that the default kinetics of anaerobic hydrolysis in ASM2d overestimated phosphorous removal in the SBRs (high anaerobic hydrolysis of pCOD). The default anaerobic hydrolysis rate in BioWin 4.1 (ten times lower) could produce similar phosphorous removal to that in the experiment. Results showed that the current kinetics of anaerobic hydrolysis in ASM2d could lead to considerable error in predicting phosphorus removal in processes with extended anaerobic HRT. Biotechnol. Bioeng. 2016;113: 2377-2385. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Enhanced Cleaning of Genesis Solar Wind Sample 61348 for Film Residue Removal

Science.gov (United States)

Allums, K. K.; Gonzalez, C. P.; Kuhlman, K. R.; Allton, J. H.

2015-01-01

The Genesis mission returned to Earth on September 8, 2004, experiencing a nonnominal reentry. During the recovery of the collector materials from the capsule, many of the collector fragments were placed on the adhesive protion of post-it notes to prevent the fragments from moving during transport back to Johnson Space Center. This unknowingly provided an additional contaminate that would prove difficult to remove with the limited chemistries allowed in the Genesis Curation Laboratory. Generally when collector material samples are prepared for allocation to PIs, the samples are cleaned front side only with Ultra-Pure Water (UPW) via megasonic dispersion to the collector surface to remove crash debris and contamination. While this cleaning method works well on samples that were not placed on post-its during recovery, it has caused movement of the residue on the back of the sample to be deposited on the front in at least two examples. Therefore, samples placed on the adhesive portion on post-it note, require enhanced cleaning methods since post-it residue has proved resistant to UPW cleaning.

TESTING OF A FULL-SCALE ROTARY MICROFILTER FOR THE ENHANCED PROCESS FOR RADIONUCLIDES REMOVAL

Energy Technology Data Exchange (ETDEWEB)

Herman, D; David Stefanko, D; Michael Poirier, M; Samuel Fink, S

2009-01-01

Savannah River National Laboratory (SRNL) researchers are investigating and developing a rotary microfilter for solid-liquid separation applications in the Department of Energy (DOE) complex. One application involves use in the Enhanced Processes for Radionuclide Removal (EPRR) at the Savannah River Site (SRS). To assess this application, the authors performed rotary filter testing with a full-scale, 25-disk unit manufactured by SpinTek Filtration with 0.5 micron filter media manufactured by Pall Corporation. The filter includes proprietary enhancements by SRNL. The most recent enhancement is replacement of the filter's main shaft seal with a John Crane Type 28LD gas-cooled seal. The feed material was SRS Tank 8F simulated sludge blended with monosodium titanate (MST). Testing examined total insoluble solids concentrations of 0.06 wt % (126 hours of testing) and 5 wt % (82 hours of testing). The following are conclusions from this testing.

Advanced Hydraulic Studies on Enhancing Particle Removal

DEFF Research Database (Denmark)

He, Cheng

clarifier. The inlet zone of an existing rectangular storm water clarifier was redesigned to improve the fluid flow conditions and reduce the hydraulic head loss in order to remove the lamellar plates and adapt the clarifier to the needs of high-rate clarification of storm water with flocculant addition...... excessive local head losses and helped to select structural changes to reduce such losses. The analysis of the facility showed that with respect to hydraulic operation, the facility is a complex, highly non-linear hydraulic system. Within the existing constraints, a few structural changes examined......The removal of suspended solids and attached pollutants is one of the main treatment processes in wastewater treatment. This thesis presents studies on the hydraulic conditions of various particle removal facilities for possible ways to increase their treatment capacity and performance by utilizing...

Removal of Retained Lead Shot Through Laparoscopic Appendectomy

Science.gov (United States)

Lloyd, D. M.

2003-01-01

We describe a patient presenting with lead shot in his appendix. A plain radiograph of his lumbar spine was performed for back pain, and an incidental finding of lead shot retained within the appendix was seen. Lead shot in the appendix is associated with appendicitis, and 2 cases have been reported of lead intoxication. We suggest that an elective laparoscopic appendectomy should be offered to patients as a possible management option. PMID:12856854

A novel approach to enhance biological nutrient removal using a culture supernatant from Micrococcus luteus containing resuscitation-promoting factor (Rpf) in SBR process.

Science.gov (United States)

Liu, Yindong; Su, Xiaomei; Lu, Lian; Ding, Linxian; Shen, Chaofeng

2016-03-01

A culture supernatant from Micrococcus luteus containing resuscitation-promoting factor (SRpf) was used to enhance the biological nutrient removal of potentially functional bacteria. The obtained results suggest that SRpf accelerated the start-up process and significantly enhanced the biological nutrient removal in sequencing batch reactor (SBR). PO4 (3-)-P removal efficiency increased by over 12 % and total nitrogen removal efficiency increased by over 8 % in treatment reactor acclimated by SRpf compared with those without SRpf addition. The Illumina high-throughput sequencing analysis showed that SRpf played an essential role in shifts in the composition and diversity of bacterial community. The phyla of Proteobacteria and Actinobacteria, which were closely related to biological nutrient removal, were greatly abundant after SRpf addition. This study demonstrates that SRpf acclimation or addition might hold great potential as an efficient and cost-effective alternative for wastewater treatment plants (WWTPs) to meet more stringent operation conditions and legislations.

Enhanced ethanol production by removal of cutin and epicuticular waxes of wheat straw by plasma assisted pretreatment

DEFF Research Database (Denmark)

Kádár, Zsófia; Schultz-Jensen, Nadja; Jensen, J. S.

2015-01-01

as with Scanning Electron Microscopy (SEM) imaging. Compounds resulting from wax degradation were analyzed in the washing water of PAP wheat straw. The wax removal enhanced enzymatic hydrolysis yield and, consequently, the efficiency of wheat straw conversion into ethanol. In total, PAP increased the conversion...

Ultrafast carrier dynamics in bimetallic nanostructure-enhanced methylammonium lead bromide perovskites.

Science.gov (United States)

Zarick, Holly F; Boulesbaa, Abdelaziz; Puretzky, Alexander A; Talbert, Eric M; DeBra, Zachary R; Soetan, Naiya; Geohegan, David B; Bardhan, Rizia

2017-01-26

In this work, we examine the impact of hybrid bimetallic Au/Ag core/shell nanostructures on the carrier dynamics of methylammonium lead tribromide (MAPbBr 3 ) mesoporous perovskite solar cells (PSCs). Plasmon-enhanced PSCs incorporated with Au/Ag nanostructures demonstrated improved light harvesting and increased power conversion efficiency by 26% relative to reference devices. Two complementary spectral techniques, transient absorption spectroscopy (TAS) and time-resolved photoluminescence (trPL), were employed to gain a mechanistic understanding of plasmonic enhancement processes. TAS revealed a decrease in the photobleach formation time, which suggests that the nanostructures improve hot carrier thermalization to an equilibrium distribution, relieving hot phonon bottleneck in MAPbBr 3 perovskites. TAS also showed a decrease in carrier decay lifetimes, indicating that nanostructures enhance photoinduced carrier generation and promote efficient electron injection into TiO 2 prior to bulk recombination. Furthermore, nanostructure-incorporated perovskite films demonstrated quenching in steady-state PL and decreases in trPL carrier lifetimes, providing further evidence of improved carrier injection in plasmon-enhanced mesoporous PSCs.

Applying carbon dioxide, plant growth-promoting rhizobacterium and EDTA can enhance the phytoremediation efficiency of ryegrass in a soil polluted with zinc, arsenic, cadmium and lead.

Science.gov (United States)

Guo, Junkang; Feng, Renwei; Ding, Yongzhen; Wang, Ruigang

2014-08-01

This study was conducted to investigate the use of elevated carbon dioxide (CO2), plant growth-promoting rhizobacterium Burkholderia sp. D54 (PGPR) and ethylenediaminetetraacetic acid (EDTA) to enhance the phytoextraction efficiency of ryegrass in response to multiple heavy metal (or metalloid)-polluted soil containing zinc (Zn), arsenic (As), cadmium (Cd) and lead (Pb). All of the single or combined CO2, PGPR and EDTA treatments promoted ryegrass growth. The stimulation of ryegrass growth by CO2 and PGPR could primarily be attributed to the regulation of photosynthesis rather than decreased levels of Zn, As and Cd in the shoots. Most treatments seemed to reduce the Zn, As and Cd contents in the shoots, which might be associated with enhanced shoot biomass, thus causing a "dilution effect" regarding their levels. The combined treatments seemed to perform better than single treatments in removing Zn, As, Cd and Pb from soil, judging from the larger biomass and relatively higher total amounts (TAs) of Zn, As, Cd and Pb in both the shoots and roots. Therefore, we suggest that the CO2 plus PGPR treatment will be suitable for removing Zn, As, Cd and Pb from heavy metal (or metalloid)-polluted soils using ryegrass as a phytoremediation material. Copyright © 2014 Elsevier Ltd. All rights reserved.

Lead removal from cathode ray tube glass by the action of calcium hydroxide and poly(vinyl chloride)

International Nuclear Information System (INIS)

Grause, Guido; Takahashi, Kenshi; Kameda, Tomohito; Yoshioka, Toshiaki

2014-01-01

Highlights: • About 99.9% of lead is removed from CRT glass by PbCl 2 volatilization. • PVC is used as chlorination agent with the aid of Ca(OH) 2 as HCl absorbing material. • The residual calcium silicate has a lead content as low as 140 mg kg −1 . • Lead leaching from the residue was below the detection limit. - Abstract: With the development of flat screen technology, the cathode ray tubes (CRTs) used in TV sets became obsolete, leaving huge amounts of lead-containing CRT glass for disposal. We developed a novel lead volatilization process in which PbCl 2 was generated in the presence of poly(vinyl chloride) (PVC) as a chlorination agent and Ca(OH) 2 as an HCl absorber. PVC was incinerated in air atmosphere and the resulting HCl was captured by Ca(OH) 2 before exiting the reactor with the air flow. CaCl 2 and Ca(OH) 2 reacted with the lead glass forming volatile PbCl 2 and crystalline Ca-silicates. Since the reactivity of lead glass with gaseous HCl is negligible, the presence of Ca(OH) 2 was essential for the success of this method. At a temperature of 1000 °C, a molar Cl/Pb ratio of 16, and a molar Ca/Si ratio of about 2, approximately 99.9% of the lead was volatilized, leaving a residue with a lead content of 140 mg kg −1 . The residual calcium silicate, with its low lead level, has the potential to be repurposed for other uses

Lead Poisoning Prevention Tips

Science.gov (United States)

... or removed safely. How are children exposed to lead? Lead-based paint and lead contaminated dust are ... What can be done to prevent exposure to lead? It is important to determine the construction year ...

Enhancement of plaque removal efficacy by tooth brushing with baking soda dentifrices: results of five clinical studies.

Science.gov (United States)

Putt, Mark S; Milleman, Kimberly R; Ghassemi, Annahita; Vorwerk, Linda M; Hooper, William J; Soparkar, Pramod M; Winston, Anthony E; Proskin, Howard M

2008-01-01

An earlier clinical study demonstrated that brushing with a commercial Arm & Hammer dentifrice containing baking soda physically removed significantly more plaque than brushing with either of two commercial dentifrices which did not contain baking soda. However, little has been done to confirm these results and to compare baking soda-containing dentifrices with more recently commercialized non-baking soda dentifrice formulations. The objective of this study was to compare commercial dentifrices containing 20% to 65% baking soda and commercial dentifrices without baking soda in enhancing plaque removal efficacy of tooth brushing. Five randomized, controlled, blinded, crossover clinical studies were performed among healthy adult volunteers who provided informed consent. After approximately 24 hours without oral hygiene, subjects with sufficient plaque were enrolled in the study phase. Plaque was scored before and after supervised brushing for one minute using the Turesky, et al. modification of the Quigley-Hein Plaque Index at six sites per tooth according to Soparkar's modification as described by Lobene, et al. In each study, wash-out periods with a regular dentifrice not evaluated in the study separated each product treatment. In all studies, every dentifrice exhibited a significant (p baking soda dentifrices resulted in statistically greater (p baking soda. Results on other tooth surfaces, such as facial, lingual, proximal, and gingival surfaces also demonstrated statistically greater (p baking soda-containing dentifrices as compared to the baking soda-free dentifrices. In three of the studies comparing different levels of baking soda, brushing with dentifrices with higher concentrations of baking soda consistently removed numerically more plaque than those containing lower levels. In one of these three studies, the difference in plaque removal between the baking soda dentifrices reached statistical significance. The results suggest a positive relationship

Multifold enhanced synergistic removal of nickel and phosphate by a (N,Fe)-dual-functional bio-sorbent: Mechanism and application

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yan-hong [State Key Laboratory of Pollution Control and Resources Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); State Environmental Protection Engineering Center for Organic Chemical Industrial Waste Water Disposal Resource Reuse, Nanjing 210023 (China); Liu, Fu-qiang, E-mail: jogia@163.com [State Key Laboratory of Pollution Control and Resources Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); State Environmental Protection Engineering Center for Organic Chemical Industrial Waste Water Disposal Resource Reuse, Nanjing 210023 (China); Zhu, Chang-qing; Zhang, Xiao-peng; Wei, Meng-meng [State Key Laboratory of Pollution Control and Resources Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); State Environmental Protection Engineering Center for Organic Chemical Industrial Waste Water Disposal Resource Reuse, Nanjing 210023 (China); Wang, Feng-he [School of Environment, Nanjing Normal University, Nanjing, 210023 (China); Ling, Chen; Li, Ai-min [State Key Laboratory of Pollution Control and Resources Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); State Environmental Protection Engineering Center for Organic Chemical Industrial Waste Water Disposal Resource Reuse, Nanjing 210023 (China)

2017-05-05

Highlights: • A (N,Fe)-dual-functional bio-sorbent was newly synthesized. • Removal of Ni(II) and H{sub 2}PO{sub 4}{sup −} could be remarkably enhanced over 3 times. • A multiple mechanism resulted in the synergic adsorption. • N/Fe-DB is efficient and repeatable in treating electroplating wastewater. - Abstract: A novel (N,Fe)-dual-functional biosorbent (N/Fe-DB) capable of efficient synergistic removal of Ni(II) and H{sub 2}PO{sub 4}{sup −} from aqueous solution was synthesized. The adsorption capacities of Ni(II) and H{sub 2}PO{sub 4}{sup −} were both remarkably enhanced over 3 times compared with those in single systems. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy confirmed that complexation of amino groups and ligand exchange of hydrous ferric oxide in N/Fe-DB played dominant roles. The electric double layer compressing and chelating ligand of deprotonated H{sub 2}PO{sub 4}{sup −} accounted for the enhanced removal of Ni(II) in binary system, while cation bridge interaction promoted uptake of H{sub 2}PO{sub 4}{sup −}. Furthermore, the coadsorbates were sequentially recovered, with the ratios of more than 99.0%. Besides, the recovered N/Fe-DB remained stable and applicable to the treatment of real electroplating wastewater even after six adsorption-regeneration cycles. Since the electroplating industry is springing up, effective control of heavy metals and phosphate has attracted global concerns. Based on the enhanced coremoval properties and superb regenerability, N/Fe-DB is potentially applicable to practical production.

Enhancement of the complete autotrophic nitrogen removal over nitrite process in a modified single-stage subsurface vertical flow constructed wetland: Effect of saturated zone depth.

Science.gov (United States)

Huang, Menglu; Wang, Zhen; Qi, Ran

2017-06-01

This study was conducted to explore enhancement of the complete autotrophic nitrogen removal over nitrite (CANON) process in a modified single-stage subsurface vertical flow constructed wetland (VSSF) with saturated zone, and nitrogen transformation pathways in the VSSF treating digested swine wastewater were investigated at four different saturated zone depths (SZDs). SZD significantly affected nitrogen transformation pathways in the VSSF throughout the experiment. As the SZD was 45cm, the CANON process was enhanced most effectively in the system owing to the notable enhancement of anammox. Correspondingly, the VSSF had the best TN removal performance [(76.74±7.30)%] and lower N 2 O emission flux [(3.50±0.22)mg·(m 2 ·h) - 1 ]. It could be concluded that autotrophic nitrogen removal via CANON process could become a primary route for nitrogen removal in the VSSF with optimized microenvironment that developed as a result of the appropriate SZD. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enhanced azo dye removal in a continuously operated up-flow anaerobic filter packed with henna plant biomass

Energy Technology Data Exchange (ETDEWEB)

Huang, Jingang, E-mail: hjg@hdu.edu.cn [Institute of Environmental Science and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); State Key Laboratory of Pollution Control and Resource Reuse, College of Environmental Science and Engineering, Tongji University, Shanghai 200092 (China); Wu, Mengke; Chen, Jianjun; Liu, Xiuyan; Chen, Tingting [Institute of Environmental Science and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Wen, Yue [State Key Laboratory of Pollution Control and Resource Reuse, College of Environmental Science and Engineering, Tongji University, Shanghai 200092 (China); Tang, Junhong; Xie, Zhengmiao [Institute of Environmental Science and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China)

2015-12-15

Highlights: • Henna stem mixed with ceramic media in UAF enhanced the removal of AO7. • Bio-reduction was the main AO7 removal pathway in henna-added UAF. • Adsorption and endogenous reduction were the main removal pathways in the control. • Henna played a multiple role in providing electron donors and redox mediator. - Abstract: Effects of henna plant biomass (stem) packed in an up-flow anaerobic bio-filter (UAF) on an azo dye (AO7) removal were investigated. AO7 removal, sulfanilic acid (SA) formation, and pseudo first-order kinetic constants for these reactions (k{sub AO7} and k{sub SA}) were higher in the henna-added UAF (R2) than in the control UAF without henna (R1). The maximum k{sub AO7} in R1 and R2 were 0.0345 and 0.2024 cm{sup −1}, respectively, on day 18; the corresponding molar ratios of SA formation to AO7 removal were 0.582 and 0.990. Adsorption and endogenous bio-reduction were the main AO7 removal pathways in R1, while in R2 bio-reduction was the dominant. Organics in henna could be released and fermented to volatile fatty acids, acting as effective electron donors for AO7 reduction, which was accelerated by soluble and/or fixed lawsone. Afterwards, the removal process weakened over time, indicating the demand of electron donation and lawsone-releasing during the long-term operation of UAF.

Enhancing organic matter removal, biopolymer recovery and electricity generation from distillery wastewater by combining fungal fermentation and microbial fuel cell.

Science.gov (United States)

Ghosh Ray, S; Ghangrekar, M M

2015-01-01

For enhancing organic matter removal from cereal-based distillery stillage two-stage treatment consisting of fermentation by Aspergillus awamori followed by microbial fuel cell (MFC) is proposed. Considerable reduction in total and soluble chemical oxygen demand (COD) up to 70% and 40%, respectively, along with 98% reduction of suspended solids (SS) has been achieved during fungal pretreatment. The process generated chitosan, a useful fermentation byproduct from fungal mycelia, as 0.6-0.7g/l of settled sludge with mycelium (3.8% solids). Prior treatment of wastewater with fungal strain enhanced the power generation in MFC by 2.9 times at an organic loading rate of 1.5kgCOD/m(3)day, demonstrating soluble COD reduction of 92% in MFC. While treating distillery wastewater, this two-stage integrated biological process demonstrated overall 99% COD removal and almost complete removal of SS, delivering ample scope for scale-up and industrial application to offer effective solution for distillery wastewater treatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

FERRATE TREATMENT FOR REMOVING CHROMIUM FROM HIGH-LEVEL RADIOACTIVE TANK WASTE

International Nuclear Information System (INIS)

Sylvester, Paul; Rutherford, Andy; Gonzalez-Martin, Anuncia; Kim, J.; Rapko, Brian M.; Lumetta, Gregg J.

2000-01-01

A method has been developed for removing chromium from alkaline high-level radioactive tank waste. Removing chromium from these wastes is critical in reducing the volume of waste requiring expensive immobilization and deep geologic disposition. The method developed is based on the oxidation of insoluble chromium(III) compounds to soluble chromate using ferrate. The tests conducted with a simulated Hanford tank sludge indicate that the chromium removal with ferrate is more efficient at 5 M NaOH than at 3 M NaOH. Chromium removal increases with increasing Fe(VI)/Cr(III) molar ratio, but the chromium removal tends to level out for Fe(VI)/Cr(III) greater than 10. Increasing temperature leads to better chromium removal, but higher temperatures also led to more rapid ferrate decomposition. Tests with radioactive Hanford tank waste generally confirmed the simulant results. In all cases examined, ferrate enhanced the chromium removal, with a typical removal of around 60-70% of the total chromium present in the washed sludge solids. The ferrate leachate solutions did not contain significant concentrations of transuranic elements, so these solutions could be handled as low-activity waste

Application of contact stabilization activated sludge for enhancing biological phosphorus removal (EBPR in domestic wastewater

Directory of Open Access Journals (Sweden)

Ehab M. Rashed

2014-04-01

Full Text Available The experiment has been performed in order to investigate the effect of using contact stabilization activated sludge as an application of enhancing biological phosphorous removal (EBPR by using contact tank as a phosphorus uptake zone and using thickening tank as a phosphorus release zone. The study involved the construction of a pilot plant which was setup in Quhafa waste water treatment plant (WWTP that included contact, final sedimentation, stabilization and thickening tanks, respectively with two returns sludge in this system one of them to contact tank and another to stabilization tank. Then observation of the uptake and release of total phosphorus by achievement through two batch test using sludge samples from thickener and final sedimentations. Results showed the removal efficiencies of COD, BOD and TP for this pilot plant with the range of 94%, 85.44% and 80.54%, respectively. On the other hand the results of batch tests showed that the reason of high ability of phosphorus removal for this pilot plant related to the high performance of microorganisms for phosphorus accumulating. Finally the mechanism of this pilot plant depends on the removal of the phosphorus from the domestic waste water as a concentrated TP solution from the supernatant above the thickening zone not through waste sludge like traditional systems.

Enhancement of oxygen transfer and nitrogen removal in a membrane separation bioreactor for domestic wastewater treatment.

Science.gov (United States)

Chiemchaisri, C; Yamamoto, K

2005-01-01

Biological nitrogen removal in a membrane separation bioreactor developed for on-site domestic wastewater treatment was investigated. The bioreactor employed hollow fiber membrane modules for solid-liquid separation so that the biomass could be completely retained within the system. Intermittent aeration was supplied with 90 minutes on and off cycle to achieve nitrification and denitrification reaction for nitrogen removal. High COD and nitrogen removal of more than 90% were achieved under a moderate temperature of 25 degrees C. As the temperature was stepwise decreased from 25 to 5 degrees C, COD removal in the system could be constantly maintained while nitrogen removal was deteriorated. Nevertheless, increasing aeration supply could enhance nitrification at low temperature with benefit from complete retention of nitrifying bacteria within the system by membrane separation. At low operating temperature range of 5 degrees C, nitrogen removal could be recovered to more than 85%. A mathematical model considering diffusion resistance of limiting substrate into the bio-particle is applied to describe nitrogen removal in a membrane separation bioreactor. The simulation suggested that limitation of the oxygen supply was the major cause of inhibition of nitrification during temperature decrease. Nevertheless, increasing aeration could promote oxygen diffusion into the bio-particle. Sufficient oxygen was supplied to the nitrifying bacteria and the nitrification could proceed. In the membrane separation bioreactor, biomass concentration under low temperature operation was allowed to increase by 2-3 times of that of moderate temperature to compensate for the loss of bacterial activities so that the temperature effect was masked.

Silver Niobate Lead-Free Antiferroelectric Ceramics: Enhancing Energy Storage Density by B-Site Doping.

Science.gov (United States)

Zhao, Lei; Gao, Jing; Liu, Qing; Zhang, Shujun; Li, Jing-Feng

2018-01-10

Lead-free dielectric ceramics with high recoverable energy density are highly desired to sustainably meet the future energy demand. AgNbO 3 -based lead-free antiferroelectric ceramics with double ferroelectric hysteresis loops have been proved to be potential candidates for energy storage applications. Enhanced energy storage performance with recoverable energy density of 3.3 J/cm 3 and high thermal stability with minimal energy density variation (<10%) over a temperature range of 20-120 °C have been achieved in W-modified AgNbO 3 ceramics. It is revealed that the W 6+ cations substitute the B-site Nb 5+ and reduce the polarizability of B-site cations, leading to the enhanced antiferroelectricity, which is confirmed by the polarization hysteresis and dielectric tunability. It is believed that the polarizability of B-site cations plays a dominant role in stabilizing the antiferroelectricity in AgNbO 3 system, in addition to the tolerance factor, which opens up a new design approach to achieve stable antiferroelectric materials.

The mechanism of enhanced wastewater nitrogen removal by photo-sequencing batch reactors based on comprehensive analysis of system dynamics within a cycle.

Science.gov (United States)

Ye, Jianfeng; Liang, Junyu; Wang, Liang; Markou, Giorgos

2018-07-01

To understand the mechanism of enhanced nitrogen removal by photo-sequencing batch reactors (photo-SBRs), which incorporated microalgal photosynthetic oxygenation into the aerobic phases of a conventional cycle, this study performed comprehensive analysis of one-cycle dynamics. Under a low aeration intensity (about 0.02 vvm), a photo-SBR, illuminated with light at 92.27 μ·mol·m -2 ·s -1 , could remove 99.45% COD, 99.93% NH 4 + -N, 90.39% TN, and 95.17% TP, while the control SBR could only remove 98.36% COD, 83.51% NH 4 + -N, 78.96% TN, and 97.75% TP, for a synthetic domestic sewage. The specific oxygen production rate (SOPR) of microalgae in the photo-SBR could reach 6.63 fmol O 2 ·cell -1 ·h -1 . One-cycle dynamics shows that the enhanced nitrogen removal by photo-SBRs is related to photosynthetic oxygenation, resulting in strengthened nitrification, instead of direct nutrient uptake by microalgae. A too high light or aeration intensity could deteriorate anoxic conditions and thus adversely affect the removal of TN and TP in photo-SBRs. Copyright © 2018 Elsevier Ltd. All rights reserved.

Removal of copper ions from aqueous solutions by means of micellar-enhanced ultrafiltration

Directory of Open Access Journals (Sweden)

Kowalska Izabela

2017-01-01

Full Text Available The aim of the study was to assess the usefulness of micellar–enhanced ultrafiltration (MEUF for removal of copper ions from water solutions in comparison with classic ultrafiltration process. The tests were conducted in a semi–pilot membrane installation with the use of ultrafiltration module KOCH/ROMICON® at a transmembrane pressure of 0.05 MPa. The effect of concentration of copper ions on ultrafiltration process efficiency was investigated. The second part of the tests concerned the removal of copper ions by MEUF under wide range of anionic surfactant concentration (0.25, 1, and 5 CMC (critical micelle concentration. Concentration of copper ions in model solutions was equal to 5, 20, and 50 mg Cu/L. Furthermore, the effect of surfactant leakage to the permeate side during filtration was evaluated. Conducted experiments confirmed effectiveness of MEUF in copper ions removal. For the highest copper concentration in the feed (i.e. 50 mg/L, the average concentration of copper ions in the permeate ranged from 1.2–4.7 mg Cu/L depending on surfactant concentration. During filtration experiments, UF module exhibited stable transport properties for model solutions containing copper. For the highest concentration of metal, the decrease of permeate flux did not exceed 11% after 60 minutes of filtration. In the presence of the surfactant, a slight deterioration of transport properties was observed.

Extracorporeal Carbon Dioxide Removal Enhanced by Lactic Acid Infusion in Spontaneously Breathing Conscious Sheep.

Science.gov (United States)

Scaravilli, Vittorio; Kreyer, Stefan; Belenkiy, Slava; Linden, Katharina; Zanella, Alberto; Li, Yansong; Dubick, Michael A; Cancio, Leopoldo C; Pesenti, Antonio; Batchinsky, Andriy I

2016-03-01

The authors studied the effects on membrane lung carbon dioxide extraction (VCO2ML), spontaneous ventilation, and energy expenditure (EE) of an innovative extracorporeal carbon dioxide removal (ECCO2R) technique enhanced by acidification (acid load carbon dioxide removal [ALCO2R]) via lactic acid. Six spontaneously breathing healthy ewes were connected to an extracorporeal circuit with blood flow 250 ml/min and gas flow 10 l/min. Sheep underwent two randomly ordered experimental sequences, each consisting of two 12-h alternating phases of ALCO2R and ECCO2R. During ALCO2R, lactic acid (1.5 mEq/min) was infused before the membrane lung. Caloric intake was not controlled, and animals were freely fed. VCO2ML, natural lung carbon dioxide extraction, total carbon dioxide production, and minute ventilation were recorded. Oxygen consumption and EE were calculated. ALCO2R enhanced VCO2ML by 48% relative to ECCO2R (55.3 ± 3.1 vs. 37.2 ± 3.2 ml/min; P less than 0.001). During ALCO2R, minute ventilation and natural lung carbon dioxide extraction were not affected (7.88 ± 2.00 vs. 7.51 ± 1.89 l/min, P = 0.146; 167.9 ± 41.6 vs. 159.6 ± 51.8 ml/min, P = 0.063), whereas total carbon dioxide production, oxygen consumption, and EE rose by 12% each (223.53 ± 42.68 vs. 196.64 ± 50.92 ml/min, 215.3 ± 96.9 vs. 189.1 ± 89.0 ml/min, 67.5 ± 24.0 vs. 60.3 ± 20.1 kcal/h; P less than 0.001). ALCO2R was effective in enhancing VCO2ML. However, lactic acid caused a rise in EE that made ALCO2R no different from standard ECCO2R with respect to ventilation. The authors suggest coupling lactic acid-enhanced ALCO2R with active measures to control metabolism.

Removal of radionuclides from household water

International Nuclear Information System (INIS)

Vesterbacka, P.; Turtiainen, T.; Haemaelaeinen, K.; Salonen, L.; Arvela, H.

2007-02-01

Research upon methods for removing radionuclides from household water was initiated in Finland in 1995. Three research projects, of which two were carried out with National Technology Agency of Finland and one with CEC, have been completed by the end of 2002. One of the main objectives of the research was to compose a guidebook for consumers and water treatment companies. Radon can be removed from household water by aeration and by activated carbon filtration. Aerators that are well designed and set up can remove over 90% of waterborne radon. The best aerators have achieved removal efficiencies that are nearly 100%. However, setting up an aeration system requires thorough planning. Also, activated carbon filtration removes radon efficiently. The removal efficiencies have been over 90%, often nearly 100%. Depending on the water quality and usage, the carbon batch inside the filter needs to be changed every 2 - 3 years. Since activated carbon filters emit gamma radiation while in use, they should not be installed inside the dwelling but in a separate building or by the well. It is recommended that uranium be removed from drinking water by anion exchange, which is the most efficient removal method for this purpose. Typically, the removal efficiencies are nearly 100%. The one exception is the so called tap filter, the removal efficiency of which depends on uranium concentration in raw water and the rate of water flow. High saline concentration in water may extricate uranium from ion exchange resin. Changes in plumbing pressure or pH-value do not have any significant influence in uranium retention. Removal efficiencies of lead and polonium vary a lot depending on the chemical form in which they occur in water. They can be reliably removed from water by reverse osmosis only. Other treatment methods, such as ion exchange and activated carbon filtration, remove lead and polonium partly. Lead and polonium are removed more efficiently when they are bound onto smaller

Electrically enhanced MBR system for total nutrient removal in remote northern applications.

Science.gov (United States)

Wei, V; Elektorowicz, M; Oleszkiewicz, J A

2012-01-01

Thousands of sparsely populated communities scatter in the remote areas of northern Canada. It is economically preferable to adopt the decentralized systems to treat the domestic wastewater because of the vast human inhabitant distribution and cold climatic conditions. Electro-technologies such as electrofiltration, elctrofloatation, electrocoagulation and electrokinetic separation have been applied in water and conventional wastewater treatment for decades due to the minimum requirements of chemicals as well as ease of operation. The membrane bioreactor (MBR) is gaining popularity in recent years as an alternative water/wastewater treatment technology. However, few studies have been conducted to hyphenate these two technologies. The purpose of this work is to design a novel electrically enhanced membrane bioreactor (EMBR) as an alternative decentralized wastewater treatment system with improved nutrient removal and reduced membrane fouling. Two identical submerged membranes (GE ZW-1 hollow fiber module) were used for the experiment, with one as a control. The EMBR and control MBR were operated for 4 months at room temperature (20 ± 2 °C) with synthetic feed and 2 months at 10 °C with real sewage. The following results were observed: (1) the transmembrane pressure (TMP) increased significantly more slowly in the EMBR and the interval between the cleaning cycles of the EMBR increased at least twice; (2) the dissolved chemical oxygen demand (COD) or total organic carbon (TOC) in the EMBR biomass was reduced from 30 to 51%, correspondingly, concentrations of the extracellular polymeric substances (EPS), the major suspicious membrane foulants, decreased by 26-46% in the EMBR; (3) both control and EMBR removed >99% of ammonium-N and >95% of dissolved COD, in addition, ortho-P removal in the EMBR was >90%, compared with 47-61% of ortho-P removal in the MBR; and (4) the advantage of the EMBR over the conventional MBR in terms of membrane fouling retardation and

Analysis and testing of W-DHR system for decay heat removal in the lead-cooled ELSY reactor

International Nuclear Information System (INIS)

Bandini, Giacomino; Meloni, Paride; Polidori, Massimiliano; Gaggini, Piero; Labanti, Valerio; Tarantino, Mariano; Cinotti, Luciano; Presciuttini, Leonardo

2009-01-01

An innovative LFR system that complies with GEN IV goals is under design in the frame of ELSY European project. ELSY is a lead-cooled pool-type reactor of about 1500 MW thermal power which normally relies on the secondary system for decay heat removal. Since the secondary system is not safety-grade and must be fully depressurized in case of detection of a steam generator tube rupture, an independent and much reliable decay heat removal (DHR) system is foreseen on the primary side. Owing to the limited capability of the Reactor Vessel Air Cooling System (RVACS) in this large power reactor, additional safety-grade loops equipped with coolers immersed in the primary coolant are necessary for an efficient removal of decay heat. Some of these loops (W-DHR) are of innovative design and may operate with water at atmospheric pressure. In the frame of the ICE program to be performed on the integral facility CIRCE at ENEA/Brasimone research centre within the EUROTRANS European project, integral circulation experiments with core heat transport and heat removal by steam generator will be conducted in a reactor pool-type configuration. Taking advantage from this experimental program, a mock-up of W-DHR heat exchanger will be tested in order to investigate its functional behavior for decay heat removal. Some pre-test calculations of W-DHR heat exchanger operation in CIRCE have been performed with the RELAP5 thermal-hydraulic code in order to support the heat exchanger design and test conduct. In this paper the experimental activity to be conducted in CIRCE and main results from W-DHR pre-test calculations are presented, along with a preliminary investigation of the W-DHR system efficiency in ELSY configuration. (author)

Lead salt resonant cavity enhanced detector with MEMS mirror

Science.gov (United States)

Felder, F.; Fill, M.; Rahim, M.; Zogg, H.; Quack, N.; Blunier, S.; Dual, J.

2010-01-01

We describe a tunable resonant cavity enhanced detector (RCED) for the mid-infrared employing narrow gap lead-chalcogenide (IV-VI) layers on a Si substrate. The device consists of an epitaxial Bragg reflector layer, a thin p-n+ heterojunction with PbSrTe as detecting layer and a micro-electro-mechanical system (MEMS) micromirror as second mirror. Despite the thin absorber layer the sensitivity is even higher than for a conventional detector. Tunability is achieved by changing the cavity length with a vertically movable MEMS mirror. The device may be used as miniature infrared spectrometer to cover the spectral range from 30 μm.

Decontamination and coating of lead

International Nuclear Information System (INIS)

Rankin, W.N.; Bush, S.P.; Lyon, C.E.; Walker, V.

1988-01-01

Technology is being developed to decontaminate lead used in shielding applications in contaminated environments for recycle as shieldings. Technology is also being developed to coat either decontaminated lead or new lead before it is used in contaminated environments. The surface of the coating is expected to be much easier to decontaminate than the original lead surface. If contamination becomes severely embedded in the coating and cannot be removed, it can be easily cut with a knife and removed from the lead. The used coating can be disposed of as radioactive (hot hazardous) waste. The lead can then be recoated for further use as a shielding material

Removal of Cu(II) in water by polymer enhanced ultrafiltration: Influence of polymer nature and pH.

Science.gov (United States)

Kochkodan, Olga D; Kochkodan, Viktor M; Sharma, Virender K

2018-01-02

This study presents an efficient removal of Cu(II) in water using the polymer enhanced ultrafiltration (PEUF) method. Polymer of different molecular weight (MW) (polyethyleneimine (PEI), sodium lignosulfonates (SLS) and dextrans) were investigated to evaluate efficiency in removal of Cu(II) in water by the PEUF method. The decomposition of Cu(II)-polymer complex was also evaluated in order to reuse polymers. Cu(II) complexation depends on the MW of chelating polymer and the pH of feed solution. It was found that the Cu(II) rejection increased with the polymer dosage with high removal of Cu(II) when using PEI and SLS at a 10:20 (mg/mg) ratio ([Cu(II)]:[polymer]). It was found that the maximum chelating capacity was 15 mg of Cu(II) per 20 mg of PEI. The Cu(II)-PEI complex could be decomposed by acid addition and the polymer could be efficiently reused with multiple complexation-decomplexation cycles. A conceptual flow chart of the integrated process of efficient removal of Cu(II) by PEUF method is suggested.

Removal Mechanisms of Para-nitrophenol in Reclaimed Water using SAT and its Bio-enhancement

Science.gov (United States)

Wen, Y. L.; Yang, Y.; Zhang, H.; Lou, B.

2017-12-01

Nowadays, we were facing with water resource shortage along with water pollution. It was important to undertake the cost effective technology to treat polluted water whilst encourage water reuse. Soil aquifer treatment (SAT) was an efficient technology, using the infiltration process of mediation, adsorption and biodegradation on the pollutants in the environment to achieve the goal of recycling water. For a better understanding of the transport and attenuation of para-nitrophenol (P-NP) and the change of microbial community at the stress of p-nitrophenol in soil aquifer treatment system, two column experiments were operated to investigate the physical, chemical, and microbial dynamics. At the same time, the bio-augment method was used to enhance the SAT biodegradation system. The SAT column experiment was operated about 38 days, which demonstrated that two reduction zones were revealed at the middle of the column and the biodiversity of the microbial community could be destroyed under the P-NP stress. Absorption was the main removal mechanism according to the obtained experimental data. By using the displacement method, the BIO-SAT system was operated about 36 days, which showed perfect outcome for the P-NP removal at a higher concentration. From the PCR-DGGE and high throughput sequencing study, enhanced bacteria could form a stable biological community with indigenous communities. Through the Canonical Correspondence Analysis (CCA) microbial degradation and environmental factors, the results showed that the pH was a very important parameter affects the degradation of nitrophenol degradation bacteria. The metal ions under the condition of low concentration can promote the growth of microbial degradation. This study provide valuable result on the attenuation potential of for the bio-enhanced SAT system (BIO-SAT). (No Image Selected)

Enhanced nitrogen removal from piggery wastewater with high NH4+ and low COD/TN ratio in a novel upflow microaerobic biofilm reactor.

Science.gov (United States)

Meng, Jia; Li, Jiuling; Li, Jianzheng; Antwi, Philip; Deng, Kaiwen; Nan, Jun; Xu, Pianpian

2018-02-01

To enhance nutrient removal more cost-efficiently in microaerobic process treating piggery wastewater characterized by high ammonium (NH 4 + -N) and low chemical oxygen demand (COD) to total nitrogen (TN) ratio, a novel upflow microaerobic biofilm reactor (UMBR) was constructed and the efficiency in nutrient removal was evaluated with various influent COD/TN ratios and reflux ratios. The results showed that the biofilm on the carriers had increased the biomass in the UMBR and enhanced the enrichment of slow-growth-rate bacteria such as nitrifiers, denitrifiers and anammox bacteria. The packed bed allowed the microaerobic biofilm process perform well at a low reflux ratio of 35 with a NH 4 + -N and TN removal as high as 93.1% and 89.9%, respectively. Compared with the previously developed upflow microaerobic sludge reactor, the UMBR had not changed the dominant anammox approach to nitrogen removal, but was more cost-efficiently in treating organic wastewater with high NH 4 + -N and low COD/TN ratio. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mechanism insights into enhanced trichloroethylene removal using xanthan gum-modified microscale zero-valent iron particles.

Science.gov (United States)

Xin, Jia; Han, Jun; Zheng, Xilai; Shao, Haibing; Kolditz, Olaf

2015-03-01

This report focuses on the enhancement in trichloroethylene (TCE) removal from contaminated groundwater using xanthan gum (XG)-modified, microscale, zero-valent iron (mZVI). Compared with bare mZVI, XG-coated mZVI increased the TCE removal efficiency by 30.37% over a 480-h experimental period. Because the TCE removal is attributed to both sorption and reduction processes, the contributions from sorption and reduction were separately investigated to determine the mechanism of XG on TCE removal using mZVI. The results showed that the TCE sorption capacity of mZVI was lower in the presence of XG, whereas the TCE reduction capacity was significantly increased. The FTIR spectra confirmed that XG, which is rich in hydrophilic functional groups, was adsorbed onto the iron surface through intermolecular hydrogen bonds, which competitively repelled the sorption and mass transfer of TCE toward reactive sites. The variations in the pH, Eh, and Fe(2+) concentration as functions of the reaction time were recorded and indicated that XG buffered the solution pH, inhibited surface passivation, and promoted TCE reduction by mZVI. Overall, the XG-modified mZVI was considered to be potentially effective for the in-situ remediation of TCE contaminated groundwater due to its high stability and dechlorination reactivity. Copyright © 2014 Elsevier Ltd. All rights reserved.

Characterization of Functionalized Polyurethane Foam for Lead Ion Removal from Water

Directory of Open Access Journals (Sweden)

Subhashini Gunashekar

2014-01-01

Full Text Available Polyurethane foams functionalized with sulfonic acid groups are used in this study to exchange lead (Pb2+ ions from aqueous solutions. Toluene-2, 4-diisocyanate, 2,6-diisocyanate (TDI was reacted with Polypropylene glycol 1200 (PPG in 2 : 1 molar ratio to form a linear prepolymer. The linear prepolymer was further polymerized using N,N-bis(2-hydroxyethyl-2-aminoethanesulfonic acid (BES, which acts both as a chain extender and an ion-exchanger for Pb2+ ions. The functionalized polyurethane foam was characterized by Fourier transform infrared spectroscopy (FTIR, gel permeation chromatography (GPC, scanning electron microscopy (SEM, and energy dispersive X-ray spectroscopy (EDX. The Pb2+ ion exchange capacity was determined using an Inductively Coupled Plasma Mass Spectrometer (ICP-MS. The maximum Pb2+ ion exchange capacity of the foam was found to be 51 ppb/g from a 100 ppb Pb2+ solution over a period of two hours. In addition, pH analysis was carried out on the foam composition with the best Pb2+ ion removal capacity. The pH results based on two-hour exposures showed that the functionalized polyurethane foam performed better at lower pH levels.

Removal of iron and manganese from groundwater: a study of using potassium permanganate and sedimentation

Directory of Open Access Journals (Sweden)

Elsheikh Mohamed

2018-01-01

Full Text Available Experiments are done for different combinations of Fe+2 and Mn+2 concentrations. The obtained results show that Potassium Permanganate (PP gives good results in iron and manganese removal. By using PP dose near to half of the theoretically required one, it can remove up to 100 % and 90 % of iron and manganese, respectively over different tested concentrations at pH=7.0. Increasing rate of filtration influences the Mn+2 removal process obviously. Sedimentation is required when combined concentrations of iron and manganese are greater than 5.0 ppm to reduce filter rapid clogging. Using conventional treatment with adding alum, flocculation, sedimentation and filtration can remove up to 97% and 18% of iron and manganese, respectively. Using PP in addition to alum enhances manganese removal but decreases iron removal. However, using alum with increasing pH to 10 leads to 100 % and 95 % of Fe+2 and Mn+2 removal and increases filter working period.

Removal of radionuclides from household water

International Nuclear Information System (INIS)

Vesterbacka, P.; Turtiainen, T.; Haemaelaeinen, K.; Salonen, L.; Arvela, H.

2003-10-01

Research upon methods for removing radionuclides from household water was initiated in Finland in 1995. Three research projects, of which two were carried out with National Technology Agency of Finland and one with CEC, have been completed by the end of 2002. One of the main objectives of the research was to compose a guidebook for consumers and water treatment companies. Radon can be removed from household water by aeration and by activated carbon filtration. Aerators that are well designed and set up can remove over 90% of waterborne radon. The best aerators have achieved removal efficiencies that are nearly 100%. However, setting up an aeration system requires thorough planning. Also, activated carbon filtration removes radon efficiently. The removal efficiencies have been over 90%, often nearly 100%. Depending on the water quality and usage, the carbon batch inside the filter needs to be changed every 2-3 years. Since activated carbon filters emit gamma radiation while in use, they should not be installed inside the dwelling but in a separate building or by the well. It is recommended that uranium be removed from drinking water by anion exchange, which is the most efficient removal method for this purpose. Typically, the removal efficiencies are nearly 100%. The one exception is the so called tap filter, the removal efficiency of which depends on uranium concentration in raw water and the rate of water flow. High saline concentration in water may extricate uranium from ion exchange resin. Changes in plumbing pressure or pH-value do not have any significant influence in uranium retention. Removal efficiencies of lead and polonium vary a lot depending on the chemical form in which they occur in water. They can be reliably removed from water by reverse osmosis only. Other treatment methods, such as ion exchange and activated carbon filtration, remove lead and polonium partly. Lead and polonium are removed more efficiently when they are bound onto smaller particles

Enhanced Removal of Hydrophobic Gas by Aerial Ultrasonic Waves and Two Kinds of Water Mists of Different Particle Sizes

Science.gov (United States)

Matsumoto, Keisuke; Miura, Hikaru

2012-07-01

Air pollutants can cause health problems, such as bronchitis and cancer, and are now recognized as a social problem. Hence, a method is proposed for the collection and removal of gaseous air pollutants by aerial ultrasonic waves and water mist. Typically, gas removal effects are studied using lemon oil vapor (“lemon gas”), which is a hydrophobic gas. Previous experiments using lemon gas have shown that a removal rate of up to 40% can be achieved in an intense standing wave at 20 kHz, for an amount of water mist of 1.39 cm3/s and an electrical input power of 50 W. Increasing the surface area of the water mist leads to greater removal of hydrophobic gas. In this study, the effects of gas removal are examined by conducting experiments using intense aerial ultrasonic waves to disperse two kinds of water mists, each composed of particles of different sizes: small particles (diameter: ≈3 µm) and conventional large particles (diameter: ≈60 µm).

Study on complexed lead and cadmium ions removal from aqueous solutions by means of ion exchange method; Studia nad usuwaniem skompleksowanych jonow olowiu i kadmu z roztworow wodnych metodami jonowymiennymi

Energy Technology Data Exchange (ETDEWEB)

Dudzinska, M. [Politechnika Lubelska, Lublin (Poland)

1992-12-31

The possibility of simultaneous removal of heavy metal ions and organic chelates from waste water has been studied. The experimental work has been preceded by extensive theoretical considerations and calculations of physico-chemical parameters of the process for model and real waste water systems. The negative influence of the presence of sulfate anions on cadmium and lead complexes removal in ion exchange process has been experimentally proved. In the systems free of sulfate anions or when their concentrations were low, the purification process conducted on Amberlite IRA-68 was very effective for cadmium and lead complexes removal. 112 refs, 78 figs, 15 tabs.

Enhanced Cr(VI) removal from groundwater by Fe0-H2O system with bio-amended iron corrosion

DEFF Research Database (Denmark)

Yin, Weizhao; Li, Yongtao; Wu, Jinhua

2017-01-01

Abstract A one-pot bio-iron system was established to investigate synergetic abiotic and biotic effects between iron and microorganisms on Cr(VI) removal. More diverse iron corrosion and reactive solids, such as green rusts, lepidocrocite and magnetite were found in the bio-iron system than...... transfer on the solid phase. The results also showed that the reduction of Cr(VI) by microorganisms was insignificant, indicating the adsorption/co-precipitation of Cr by iron oxides on iron surface was responsible for the overall Cr(VI) removal. Our study demonstrated that the bio-amended iron corrosion...... in the Fe0-H2O system, leading to 4.3 times higher Cr(VI) removal efficiency in the bio-iron system than in the Fe0-H2O system. The cycling experiment also showed that the Cr(VI) removal capacity of Fe0 in the bio-iron system was 12.4 times higher than that in the Fe0-H2O system. A 62 days of life...

Applying fermentation liquid of food waste as carbon source to a pilot-scale anoxic/oxic-membrane bioreactor for enhancing nitrogen removal: Microbial communities and membrane fouling behaviour.

Science.gov (United States)

Tang, Jialing; Wang, Xiaochang C; Hu, Yisong; Ngo, Huu Hao; Li, Yuyou; Zhang, Yongmei

2017-07-01

Fermentation liquid of food waste (FLFW) was applied as an external carbon source in a pilot-scale anoxic/oxic-membrane bioreactor (A/O-MBR) system to enhance nitrogen removal for treating low COD/TN ratio domestic wastewater. Results showed that, with the FLFW addition, total nitrogen removal increased from lower than 20% to 44-67% during the 150days of operation. The bacterial metabolic activities were obviously enhanced, and the significant change in microbial community structure promoted pollutants removal and favored membrane fouling mitigation. By monitoring transmembrane pressure and characterizing typical membrane foulants, such as extracellular polymeric substances (EPS), dissolved organic matter (DOM), and inorganics and biopolymers in the cake layer, it was confirmed that FLFW addition did not bring about any additional accumulation of membrane foulants, acceleration of fouling rate, or obvious irreversible membrane fouling in the whole operation period. Therefore, FLFW is a promising alternative carbon source to enhance nitrogen removal for the A/O-MBR system. Copyright © 2017 Elsevier Ltd. All rights reserved.

Iodine removing method in organic solvent

International Nuclear Information System (INIS)

Suzuki, Takeo; Sakurai, Manabu

1988-01-01

Purpose: To effectively remove iodine in an organic solvent to thereby remove iodine in the solvent that can be re-used or put to purning treatment. Method: Organic solvent formed from wastes of nuclear facilities is mixed with basic lead acetate, or silica gel or activated carbon incorporated with such a compound to adsorb iodine in the organic solvent to the basic lead acetate. Then, iodine in the organic solvent is removed by separating to eliminate the basic lead acetate adsorbing iodine from the organic solvent or by passing the organic solvent through a tower or column charged or pre-coated with silica gel or activated carbon incorporated with lead acetate. By using basic lead acetate as the adsorbents, iodine can effective by adsorbed and eliminated. Thus, the possibility of circumstantial release of iodine can be reduced upon reusing or burning treatment of the organic solvent. (Kamimura, M.)

Removal of lead from the industrial and synthetic Cu-Pb-Fe alloy with argon barbotage

Directory of Open Access Journals (Sweden)

B. Oleksiak

2012-01-01

Full Text Available Results of research on removal of lead from synthetic and industrial Cu-Pb-Fe alloy with argon barbotage are presented. For examinations was taken a synthetic alloy and industrial alloy coming “Glogow II” Copperworks. As basic research equipment was used a pipe resistance furnace enabling heating of samples up to 1 473 K. Examinations were made in 2 test series. The 1 series was performed on the synthetic alloy, while in 2 series was used an industrial alloy. All series were conducted at 1 473 K and with gas fl ow 5,55•10-6, 6,94•10-6, 8,33•10-6, 9,72•10-6 m3•s-1.

Long term operation of continuous-flow system with enhanced biological phosphorus removal granules at different COD loading.

Science.gov (United States)

Li, Dong; Lv, Yufeng; Zeng, Huiping; Zhang, Jie

2016-09-01

In this study, a continuous-flow system with enhanced biological phosphorus removal (EBPR) granules was operated at different COD concentrations (200, 300 and 400mgL(-)(1)) to investigate the effect of COD loading on this system. The results showed that when the COD concentration in influent was increased to 400mgL(-)(1), the anaerobic COD removal efficiency and total phosphorus removal efficiency reduced obviously and the settling ability of granules deteriorated due to the proliferation of filamentous bacteria. Moreover, high COD loading inhibited the EPS secretion and destroyed the stability of granules. Results of high-through pyrosequencing indicated that filamentous bacteria had a competitive advantage over polyphosphate-accumulating organisms (PAOs) at high COD loading. The performance of system, settling ability of granules and proportion of PAOs gradually recovered to the initial level after the COD concentration was reduced to 200mgL(-)(1) on day 81. Copyright © 2016 Elsevier Ltd. All rights reserved.

Enhanced Stormwater Contaminant Removal Using Tree Filters And Modified Sorbents

Science.gov (United States)

Schifman, L. A.; Kasaraneni, V. K.; Boving, T. B.; Oyanedel-Craver, V.

2012-12-01

Stormwater runoff, particularly in urban areas, contains several groups of contaminants that negatively impact surface- and groundwater quality if left untreated. Contaminants in runoff are often addressed by structural best management practices (BMP) that capture and treat runoff before discharging it. Many BMPs, such as tree filters, act as primary filtration devices that attenuate total suspended solids, nutrients, and heavy metals from runoff; but typically these BMPs are not designed to treat bacteria and have only minor petroleum hydrocarbon (PH) treatment capabilities. To address this shortcoming, three materials (red cedar wood chips, expanded shale, and crushed concrete) were modified with either Quaternary Ammonium Silane (QAS) or Silver Nanoparticles (AgNPs) to provide antimicrobial properties to the matrix and/or exploit their affinity to sorb PH, particularly polycyclic aromatic hydrocarbons (PAH). Results show that of the three materials investigated, wood chips exhibit the highest sorption capacity for QAS, making this material favorable for treating bacteria, while at the same time attenuating PAHs by sorption processes. In case of AgNP amendments to wood, less uptake and more desorption from the wood matrix was observed. Relative to wood, expanded shale and crushed concrete exhibited less affinity for QAS (results for AgNPs are pending). Currently, batch isotherm and unsaturated flow column studies are under way to determine the performance of the amended materials with regard to removal of bacteria, nutrients, heavy metals, and PAH from artificially contaminated runoff. In this presentation, the contaminant removal efficiency of all modified and unmodified materials will be discussed on the background of how these materials may find use in enhanced treatment of stormwater in tree filter BMPs.

Application of Gamma Radiation to Enhance Heavy Metals Removal Efficiency to Bacteria Isolated from Ronpiboon District, Nakhon Sri Thamarat Province, Thailand

International Nuclear Information System (INIS)

Intrasungkha, Nugul; Wisapan, Walakon; Piadang, Nattayana

2006-09-01

The objective of this study was to isolate soil bacteria capable to te move 4 heavy metals, namely, arsenic (As(III)), lead Pb(II) and cadmium f ron old tin mine in Ronpiboon district, Nakhon Sri Thamarat. It was found that there were bacteria which capable to resist arsenic, lead and copper 11, 15, 8 and 2 ileitis, respectively[evacuate;y. The arsenic removal efficiency of these bacteria was evaluated at the low concentration of 1 u g/l. with the results of 7-61%. The lead and copper removal efficiencies at 10 mg/l were found at the range pf 9-98% and 8-40%, respectively. Six isolates of bacteria (KRD, KRH, KRM, KCD13 and KCD14) were selected to be irradiated by gamma radiation at the levels of 2-10 kGy. The heavy metals resistance was found increase in the range of of 125-16% for arsenic, 0-50% for copper, 0-18% for lead and 0-17% for cadmium, respectively. Also ut was found that the low temperature at 4 and -40 degree Celsius can prolong the bacterial survival up to 6 months. Later the arsenic removal experiment in liquid medium was conducted and it was found that the mutants can perform slightly better than wild type only >17%. It was due to the initial concentration of arsenic was too high (10 mg/l). The preliminary study of arsenic removal in soil was also conducted using pack-bed reactor. We found the proper ratio of pack material (soil and gravel) was 1:1 to promote the liquid and air circulation. The suitable medium was found to be acidified mo lass solution which were found promote the growth of tested bacterial isolates.

Enhanced bioremoval of lead by earthworm-Lumbricus terrestris co-cultivated with bacteria-Klebsiella variicola.

Science.gov (United States)

Das, Anamika; Osborne, Jabez W

2017-10-01

Lead is a toxic heavy metal having devastating effects on the environment. The current study was focussed on bioremoval of lead using earthworm and lead resistant bacteria. Earthworms were subjected to various concentrations of lead in the soil bioaugmented with lead resistant bacteria (VITMVCJ1) to enhance the uptake of lead from the contaminated soil. Significant increase was observed in the length and body weight of the earthworms supplemented with lead resistant bacteria. Similarly, there was a substantial increase in the locomotion rate of the earthworms treated with lead resistant bacteria in comparison with the control. The gut micro flora of bacterial treated earthworms had increased number of bacterial cells than the untreated earthworms. The histopathological studies revealed the toxic effects of lead on the gut of earthworms indicating severe damage in lead resistant bacteria untreated worms, whereas the cells were intact in lead resistant bacteria treated worms. COMET assay showed increased DNA damage with higher tail DNA percent in the untreated earthworms. Further, the colonisation of the bacteria supplemented, onto the gut region of earthworms was observed by scanning electron microscopy. Atomic absorption spectrophotometry indicated a fair 50% uptake of lead within the biomass of earthworm treated with lead resistant bacteria. Copyright © 2017 Elsevier B.V. All rights reserved.

Remediation of lead-contaminated soils

International Nuclear Information System (INIS)

Peters, R.W.; Shem, L.

1992-01-01

Excavation and transport of soil contaminated with heavy metals has generally been the standard remediation technique for treatment of heavy-metal-contaminated soils. This approach is not a permanent solution; moreover, off-site shipment and disposal of contaminated soil involves high expense, liability, and appropriate regulatory approval. Recently, a number of other techniques have been investigated for treating such contaminated sites, including flotation, solidification/stabilization, vitrification, and chemical extraction. This paper reports the results of a laboratory investigation determining the efficiency of using chelating agents to extract lead from contaminated soils. Lead concentrations in the soils ranged from 500 to 10,000 mg/kg. Ethylenediaminetetraacetic acid (EDTA) and nitrilotriacetic acid (NTA) were examined for their potential extractive capabilities. Concentrations of the chelating agents ranged from 0.01 to 0.10 M. The pH of the suspensions in which the extractions were performed ranged from 4 to 12. Results showed that the removal of lead using NTA and water was ph-dependent, whereas the removal of lead using EDTA was ph-insensitive. Maximum removals of lead were 68.7%,19.1%, and 7.3% using EDTA, NTA, and water, respectively (as compared with initial lead concentrations)

Enhancement of Fenton oxidation for removing organic matter from hypersaline solution by accelerating ferric system with hydroxylamine hydrochloride and benzoquinone.

Science.gov (United States)

Peng, Siwei; Zhang, Weijun; He, Jie; Yang, Xiaofang; Wang, Dongsheng; Zeng, Guisheng

2016-03-01

Fenton oxidation is generally inhibited in the presence of a high concentration of chloride ions. This study investigated the feasibility of using benzoquinone (BQ) and hydroxylamine hydrochloride (HA) as Fenton enhancers for the removal of glycerin from saline water under ambient temperature by accelerating the ferric system. It was found that organics removal was not obviously affected by chloride ions of low concentration (less than 0.1mol/L), while the mineralization rate was strongly inhibited in the presence of a large amount of chloride ions. In addition, ferric hydrolysis-precipitation was significantly alleviated in the presence of HA and BQ, and HA was more effective in reducing ferric ions into ferrous ions than HA, while the H2O2 decomposition rate was higher in the BQ-Fenton system. Electron spin resonance analysis revealed that OH production was reduced in high salinity conditions, while it was enhanced after the addition of HA and BQ (especially HA). This study provided a possible solution to control and alleviate the inhibitory effect of chloride ions on the Fenton process for organics removal. Copyright © 2015. Published by Elsevier B.V.

Removal of Silicone Oil From Intraocular Lens Using Novel Surgical Materials

Science.gov (United States)

Paschalis, Eleftherios I.; Eliott, Dean; Vavvas, Demetrios G.

2014-01-01

Purpose To design, fabricate, and evaluate novel materials to remove silicone oil (SiO) droplets from intraocular lenses (IOL) during vitreoretinal surgery. Methods Three different designs were fabricated using soft lithography of polydimethylsiloxane (PDMS), three-dimensional (3D) inverse PDMS fabrication using water dissolvable particles, and atomic layer deposition (ALD) of alumina (Al2O3) on surgical cellulose fibers. Laboratory tests included static and dynamic contact angle (CA) measurements with water and SiO, nondestructive x-ray microcomputer tomography (micro-CT), and microscopy. SiO removal was performed in vitro and ex vivo using implantable IOLs and explanted porcine eyes. Results All designs exhibited enhanced hydrophobicity and oleophilicity. Static CA measurements with water ranged from 131° to 160° and with SiO CA approximately 0° in 120 seconds following exposure. Nondestructive x-ray analysis of the 3D PDMS showed presence of interconnected polydispersed porosity of 100 to 300 μm in diameter. SiO removal from IOLs was achieved in vitro and ex vivo using standard 20-G vitrectomy instrumentation. Conclusion Removal of SiO from IOLs can be achieved using materials with lower surface energy than that of the IOLs. This can be achieved using appropriate surface chemistry and surface topography. Three designs, with enhanced hydrophobic properties, were fabricated and tested in vitro and ex vivo. All materials remove SiO within an aqueous environment. Preliminary ex vivo results were very promising, opening new possibilities for SiO removal in vitreoretinal surgeries. Translational Relevance This is the first report of an instrument that can lead to successful removal of SiO from the surface of IOL. In addition to the use of this instrument/material in medicine it can also be used in the industry, for example, retrieval of oil spills from bodies of water. PMID:25237593

Removal of Silicone Oil From Intraocular Lens Using Novel Surgical Materials.

Science.gov (United States)

Paschalis, Eleftherios I; Eliott, Dean; Vavvas, Demetrios G

2014-09-01

To design, fabricate, and evaluate novel materials to remove silicone oil (SiO) droplets from intraocular lenses (IOL) during vitreoretinal surgery. Three different designs were fabricated using soft lithography of polydimethylsiloxane (PDMS), three-dimensional (3D) inverse PDMS fabrication using water dissolvable particles, and atomic layer deposition (ALD) of alumina (Al 2 O 3 ) on surgical cellulose fibers. Laboratory tests included static and dynamic contact angle (CA) measurements with water and SiO, nondestructive x-ray microcomputer tomography (micro-CT), and microscopy. SiO removal was performed in vitro and ex vivo using implantable IOLs and explanted porcine eyes. All designs exhibited enhanced hydrophobicity and oleophilicity. Static CA measurements with water ranged from 131° to 160° and with SiO CA approximately 0° in 120 seconds following exposure. Nondestructive x-ray analysis of the 3D PDMS showed presence of interconnected polydispersed porosity of 100 to 300 μm in diameter. SiO removal from IOLs was achieved in vitro and ex vivo using standard 20-G vitrectomy instrumentation. Removal of SiO from IOLs can be achieved using materials with lower surface energy than that of the IOLs. This can be achieved using appropriate surface chemistry and surface topography. Three designs, with enhanced hydrophobic properties, were fabricated and tested in vitro and ex vivo. All materials remove SiO within an aqueous environment. Preliminary ex vivo results were very promising, opening new possibilities for SiO removal in vitreoretinal surgeries. This is the first report of an instrument that can lead to successful removal of SiO from the surface of IOL. In addition to the use of this instrument/material in medicine it can also be used in the industry, for example, retrieval of oil spills from bodies of water.

Highly effective removal of mercury and lead ions from wastewater by mercaptoamine-functionalised silica-coated magnetic nano-adsorbents: Behaviours and mechanisms

Energy Technology Data Exchange (ETDEWEB)

Bao, Shuangyou; Li, Kai; Ning, Ping [Faculty of Environmental Science and Engineering, Kunming University of Science and Technology, YunNan, KunMing, 650500 (China); Peng, Jinhui [Faculty of Metallurgical and Energy, Kunming University of Science and Technology, YunNan, KunMing 650500 (China); Jin, Xu [Faculty of Environmental Science and Engineering, Kunming University of Science and Technology, YunNan, KunMing, 650500 (China); Tang, Lihong, E-mail: luckyman@163.com [Faculty of Environmental Science and Engineering, Kunming University of Science and Technology, YunNan, KunMing, 650500 (China)

2017-01-30

Highlights: • Highly effective removal of Hg(II) and Pb(II) ions from wastewater. • This adsorbent had multiple adsorption sites (sulfur and amine sites) on the surface. • This adsorbent had better tolerance to low pH for removal of Hg(II). • This new hybrid material was much cheaper and no secondary pollution. • This adsorbent shows notable advantages including easy separation and recyclability. - Abstract: A novel hybrid material was fabricated using mercaptoamine-functionalised silica-coated magnetic nanoparticles (MAF-SCMNPs) and was effective in the extraction and recovery of mercury and lead ions from wastewater. The properties of this new magnetic material were explored using various characterisation and analysis methods. Adsorbent amounts, pH levels and initial concentrations were optimised to improve removal efficiency. Additionally, kinetics, thermodynamics and adsorption isotherms were investigated to determine the mechanism by which the fabricated MAF-SCMNPs adsorb heavy metal ions. The results revealed that MAF-SCMNPs were acid-resistant. Sorption likely occurred by chelation through the amine group and ion exchange between heavy metal ions and thiol functional groups on the nanoadsorbent surface. The equilibrium was attained within 120 min, and the adsorption kinetics showed pseudo-second-order (R{sup 2} > 0.99). The mercury and lead adsorption isotherms were in agreement with the Freundlich model, displaying maximum adsorption capacities of 355 and 292 mg/g, respectively. The maximum adsorptions took place at pH 5–6 and 6–7 for Hg(II) and Pb(II), respectively. The maximum adsorptions were observed at 10 mg and 12 mg adsorbent quantities for Hg(II) and Pb(II), respectively. The adsorption process was endothermic and spontaneous within the temperature range of 298–318 K. This work demonstrates a unique magnetic nano-adsorbent for the removal of Hg(II) and Pb(II) from wastewater.

[Enhanced nitrogen and phosphorus removal of wastewater by using sludge anaerobic fermentation liquid as carbon source in a pilot-scale system].

Science.gov (United States)

Luo, Zhe; Zhou, Guang-Jie; Liu, Hong-Bo; Nie, Xin-Yu; Chen, Yu; Zhai, Li-Qin; Liu, He

2015-03-01

In order to explore the possibility of enhanced nitrogen and phosphorus removal in wastewater using sludge anaerobic fermentation liquid as external carbon source, the present study proposed an A2/O reactor system with a total effective volume of 4 660 L and real municipal wastewater for treatment. The results showed that under the conditions of the influent COD at 243.7 mg x L(-1), NH4(+) -N at 30. 9 mg x L(-1), TN at 42.9 mg'L- , TP at 2.8 mg x L(-1), the backflow ratio of nitrification liquid at 200% and recycle ratio of sludge at 100%, the addition of acetic acid into anoxic tank could enhance the removal efficiency of nitrogen and phosphorus, and the optimal influent quantity and SCOD incremental of carbon were 7 500 L x d(-1) and 50 mg L(-1), respectively. When the sludge fermentation liquid was used as external carbon source and the average effluent COD, NH4(+) -N, TN, TP removal efficiency were 81.60%, 88.91%, 64.86% and 87.61%, the effluent concentrations were 42.18, 2.77, 11.92 and 0.19 mg x L(-1), respectively, which met China's first Class (A) criteria specified in the Discharge Standard Urban Sewage Treatment Plant Pollutant (GB 18918-2002). The results of the present study demonstrated that the addition of sludge anaerobic fermented liquid as external carbon source was a feasible way to enhance the removal of nitrogen and phosphorous in municipal wastewater, providing a new feasible strategy for the reuse and recycle of sewage sludge in China.

The modelling of lead removal from water by deep eutectic solvents functionalized CNTs: artificial neural network (ANN) approach.

Science.gov (United States)

Fiyadh, Seef Saadi; AlSaadi, Mohammed Abdulhakim; AlOmar, Mohamed Khalid; Fayaed, Sabah Saadi; Hama, Ako R; Bee, Sharifah; El-Shafie, Ahmed

2017-11-01

The main challenge in the lead removal simulation is the behaviour of non-linearity relationships between the process parameters. The conventional modelling technique usually deals with this problem by a linear method. The substitute modelling technique is an artificial neural network (ANN) system, and it is selected to reflect the non-linearity in the interaction among the variables in the function. Herein, synthesized deep eutectic solvents were used as a functionalized agent with carbon nanotubes as adsorbents of Pb 2+ . Different parameters were used in the adsorption study including pH (2.7 to 7), adsorbent dosage (5 to 20 mg), contact time (3 to 900 min) and Pb 2+ initial concentration (3 to 60 mg/l). The number of experimental trials to feed and train the system was 158 runs conveyed in laboratory scale. Two ANN types were designed in this work, the feed-forward back-propagation and layer recurrent; both methods are compared based on their predictive proficiency in terms of the mean square error (MSE), root mean square error, relative root mean square error, mean absolute percentage error and determination coefficient (R 2 ) based on the testing dataset. The ANN model of lead removal was subjected to accuracy determination and the results showed R 2 of 0.9956 with MSE of 1.66 × 10 -4 . The maximum relative error is 14.93% for the feed-forward back-propagation neural network model.

Lead immobilization by geological fluorapatite and fungus Aspergillus niger.

Science.gov (United States)

Li, Zhen; Wang, Fuwei; Bai, Tongshuo; Tao, Jinjin; Guo, Jieyun; Yang, Mengying; Wang, Shimei; Hu, Shuijin

2016-12-15

Phosphate solubilizing fungi have high ability to secrete organic acids. In this study, fungus Aspergillus niger and geological fluorapatite were applied in lead remediation in aqueous solution. Formation and morphology of the lead minerals, e.g., pyromorphite and lead oxalate, were investigated by SEM, XRD, and ATR-IR. The total quantity of organic acids reached the maximum at the sixth day, which improved the concentration of soluble P up to ∼370mg/L from ∼0.4mg/L. The organic acids, especially the oxalic acid, enhance the solubility of fluorapatite significantly. The stable fluoropyromorphite [Pb 5 (PO 4 ) 3 F] is precipitated with the elevated solubility of fluorapatite in the acidic environment. Furthermore, A. niger grows normally with the presence of lead cations. It is shown that >99% lead cations can be removed from the solution. However, immobilization caused by the precipitation of lead oxalate cannot be ignored if the fungus A. niger was cultured in the Pb solution. This study elucidates the mechanisms of lead immobilization by FAp and A. niger, and sheds its perspective in lead remediation, especially for high Pb concentration solution. Copyright © 2016 Elsevier B.V. All rights reserved.

Simultaneous removal of NO and SO2 using vacuum ultraviolet light (VUV)/heat/peroxymonosulfate (PMS).

Science.gov (United States)

Liu, Yangxian; Wang, Yan; Wang, Qian; Pan, Jianfeng; Zhang, Jun

2018-01-01

Simultaneous removal process of SO 2 and NO from flue gas using vacuum ultraviolet light (VUV)/heat/peroxymonosulfate (PMS) in a VUV spraying reactor was proposed. The key influencing factors, active species, reaction products and mechanism of SO 2 and NO simultaneous removal were investigated. The results show that vacuum ultraviolet light (185 nm) achieves the highest NO removal efficiency and yield of and under the same test conditions. NO removal is enhanced at higher PMS concentration, light intensity and oxygen concentration, and is inhibited at higher NO concentration, SO 2 concentration and solution pH. Solution temperature has a double impact on NO removal. CO 2 concentration has no obvious effect on NO removal. and produced from VUV-activation of PMS play a leading role in NO removal. O 3 and ·O produced from VUV-activation of O 2 also play an important role in NO removal. SO 2 achieves complete removal under all experimental conditions due to its very high solubility in water and good reactivity. The highest simultaneous removal efficiency of SO 2 and NO reaches 100% and 91.3%, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Application of bifunctional Saccharomyces cerevisiae to remove lead(II) and cadmium(II) in aqueous solution

International Nuclear Information System (INIS)

Zhang Yunsong; Liu Weiguo; Zhang Li; Wang Meng; Zhao Maojun

2011-01-01

A magnetic adsorbent, EDTAD-functionalized Saccharomyces cerevisiae, has been synthesized to behave as an adsorbent for heavy metal ions by adjusting the pH value of the aqueous solution to make carboxyl and amino groups protonic or non-protonic. The bifunctional Saccharomyces cerevisiae (EMS) were used to remove lead(II) and cadmium(II) in solution in a batch system. The results showed that the adsorption capacity of the EMS for the heavy metal ions increased with increasing solution pH, and the maximum adsorption capacity (88.16 mg/g for Pb 2+ , 40.72 mg/g for Cd 2+ ) at 10 deg. C was found to occur at pH 5.5 and 6.0, respectively. The adsorption process followed the Langmuir isotherm model. The regeneration experiments revealed that the EMS could be successfully reused.

Nanodomain Engineered (K, Na)NbO3 Lead-Free Piezoceramics: Enhanced Thermal and Cycling Reliabilities

DEFF Research Database (Denmark)

Yao, Fang-Zhou; Wang, Ke; Cheng, Li-Qian

2015-01-01

- based materials, accepting the drawbacks of high temperature and cycling instabilities. Here, we present that CaZrO3-modified (K, Na)NbO3 piezoceramics not only possess excellent performance at ambient conditions benefiting from nanodomain engineering, but also exhibit superior stability against......The growing environmental concerns have been pushing the development of viable green alternatives for lead-based piezoceramics to be one of the priorities in functional ceramic materials. A polymorphic phase transition has been utilized to enhance piezoelectric properties of lead-free (K, Na)NbO3...... temperature fluctuation and electrical fatigue cycling. It was found that the piezoelectric coefficient d33 is temperature independent under 4 kV/mm, which can be attributed to enhanced thermal stability of electric field engineered domain configuration; whereas the electric field induced strain exhibits...

Use of adsorption using granular activated carbon (GAC) for the enhancement of removal of chromium from synthetic wastewater by electrocoagulation.

Science.gov (United States)

Vivek Narayanan, N; Ganesan, Mahesh

2009-01-15

The present work deals with removal of hexavalent chromium from synthetic effluents in a batch stirred electrocoagulation cell with iron-aluminium electrode pair coupled with adsorption using granular activated carbon (GAC). Several working parameters such as pH, current density, adsorbent concentration and operating time were studied in an attempt to achieve higher removal capacity. Results obtained with synthetic wastewater revealed that most effective removal capacities of chromium (VI) could be achieved when the initial pH was near 8. The removal of chromium (VI) during electrocoagulation, is due to the combined effect of chemical precipitation, coprecipitation, sweep coagulation and adsorption. In addition, increasing current density in a range of 6.7-26.7mA/cm2 and operating time from 20 to 100min enhanced the treatment rate to reduce metal ion concentration below admissible legal levels. The addition of GAC as adsorbent resulted in remarkable increase in the removal rate of chromium at lower current densities and operating time, than the conventional electrocoagulation process. The method was found to be highly efficient and relatively fast compared to existing conventional techniques.

Fractional Factorial Design Study on the Performance of GAC-Enhanced Electrocoagulation Process Involved in Color Removal from Dye Solutions

Directory of Open Access Journals (Sweden)

Iuliana Gabriela Breaban

2013-07-01

Full Text Available The aim of this study was to determine the effects of main factors and interactions on the color removal performance from dye solutions using the electrocoagulation process enhanced by adsorption on Granular Activated Carbon (GAC. In this study, a mathematical approach was conducted using a two-level fractional factorial design (FFD for a given dye solution. Three textile dyes: Acid Blue 74, Basic Red 1, and Reactive Black 5 were used. Experimental factors used and their respective levels were: current density (2.73 or 27.32 A/m2, initial pH of aqueous dye solution (3 or 9, electrocoagulation time (20 or 180 min, GAC dose (0.1 or 0.5 g/L, support electrolyte (2 or 50 mM, initial dye concentration (0.05 or 0.25 g/L and current type (Direct Current—DC or Alternative Pulsed Current—APC. GAC-enhanced electrocoagulation performance was analyzed statistically in terms of removal efficiency, electrical energy, and electrode material consumptions, using modeling polynomial equations. The statistical significance of GAC dose level on the performance of GAC enhanced electrocoagulation and the experimental conditions that favor the process operation of electrocoagulation in APC regime were determined. The local optimal experimental conditions were established using a multi-objective desirability function method.

Fractional Factorial Design Study on the Performance of GAC-Enhanced Electrocoagulation Process Involved in Color Removal from Dye Solutions.

Science.gov (United States)

Secula, Marius Sebastian; Cretescu, Igor; Cagnon, Benoit; Manea, Liliana Rozemarie; Stan, Corneliu Sergiu; Breaban, Iuliana Gabriela

2013-07-10

The aim of this study was to determine the effects of main factors and interactions on the color removal performance from dye solutions using the electrocoagulation process enhanced by adsorption on Granular Activated Carbon (GAC). In this study, a mathematical approach was conducted using a two-level fractional factorial design ( FFD ) for a given dye solution. Three textile dyes: Acid Blue 74, Basic Red 1, and Reactive Black 5 were used. Experimental factors used and their respective levels were: current density (2.73 or 27.32 A/m²), initial pH of aqueous dye solution (3 or 9), electrocoagulation time (20 or 180 min), GAC dose (0.1 or 0.5 g/L), support electrolyte (2 or 50 mM), initial dye concentration (0.05 or 0.25 g/L) and current type (Direct Current- DC or Alternative Pulsed Current- APC ). GAC-enhanced electrocoagulation performance was analyzed statistically in terms of removal efficiency, electrical energy, and electrode material consumptions, using modeling polynomial equations. The statistical significance of GAC dose level on the performance of GAC enhanced electrocoagulation and the experimental conditions that favor the process operation of electrocoagulation in APC regime were determined. The local optimal experimental conditions were established using a multi-objective desirability function method.

A change in strategy for a CERCLA Removal Action Demolition Project in progress results in overall project enhancements

International Nuclear Information System (INIS)

Albertin, M.; Nichols, R.M.; Edwards, D.T.

1995-01-01

This paper discusses changes made in a demolition project at the Fernald Environmental Management Project (FEMP), a site on the National Priorities list (NPL), owned by the Department of Energy. The project, to demolish fourteen uranium ore silos and their structure, was based on a Removal Action Work Plan, submitted and approved by the United States Environmental Protection Agency (USEPA), that integrated Comprehensive Environmental Response Compensation and Liability Act (CERCLA) requirements to remove the source of contamination and threat to public health and the environment. After the demolition contractor defaulted at 30% complete, completion of the project by the USEPA deadline was threatened. The recovery plan included re-evaluation of project documents in addition to the schedule. It was determined that re-interpretation of the removal action criteria, including design and Removal Action Work Plan, would eliminate road-blocks, and optimize resources, resulting in project completion by the original deadline even after lost-time in mobilizing another contractor. This presentation will discuss the open-quotes lessons learnedclose quotes by the project team and illustrate how simplification of construction methods resulted in enhancements to the environmental controls, improved material handing, and created a safer work environment

Laser-based coatings removal

International Nuclear Information System (INIS)

Freiwald, J.G.; Freiwald, D.A.

1995-01-01

Over the years as building and equipment surfaces became contaminated with low levels of uranium or plutonium dust, coats of paint were applied to stabilize the contaminants in place. Most of the earlier paint used was lead-based paint. More recently, various non-lead-based paints, such as two-part epoxy, are used. For D ampersand D (decontamination and decommissioning), it is desirable to remove the paints or other coatings rather than having to tear down and dispose of the entire building. This report describes the use of pulse-repetetion laser systems for the removal of paints and coatings

Laser-based coatings removal

Energy Technology Data Exchange (ETDEWEB)

Freiwald, J.G.; Freiwald, D.A. [F2 Associates, Inc., Albuquerque, NM (United States)

1995-10-01

Over the years as building and equipment surfaces became contaminated with low levels of uranium or plutonium dust, coats of paint were applied to stabilize the contaminants in place. Most of the earlier paint used was lead-based paint. More recently, various non-lead-based paints, such as two-part epoxy, are used. For D&D (decontamination and decommissioning), it is desirable to remove the paints or other coatings rather than having to tear down and dispose of the entire building. This report describes the use of pulse-repetetion laser systems for the removal of paints and coatings.

Process for lead removal from rare earth

International Nuclear Information System (INIS)

Bollat, A.; Sabot, J.L.

1987-01-01

An aqueous solution of rare earth chlorides and lead chlorides, with a chloride concentration of at least 2 moles/liter and a pH between 2 and 4, is extracted by an alkylphosphonic acid ester and rare earth(s) is (are) recovered from the organic phase [fr

Enhanced NIF neutron activation diagnostics.

Science.gov (United States)

Yeamans, C B; Bleuel, D L; Bernstein, L A

2012-10-01

The NIF neutron activation diagnostic suite relies on removable activation samples, leading to operational inefficiencies and a fundamental lower limit on the half-life of the activated product that can be observed. A neutron diagnostic system measuring activation of permanently installed samples could remove these limitations and significantly enhance overall neutron diagnostic capabilities. The physics and engineering aspects of two proposed systems are considered: one measuring the (89)Zr/(89 m)Zr isomer ratio in the existing Zr activation medium and the other using potassium zirconate as the activation medium. Both proposed systems could improve the signal-to-noise ratio of the current system by at least a factor of 5 and would allow independent measurement of fusion core velocity and fuel areal density.

Novel adsorption and photocatalytic oxidation for removal of gaseous toluene by V-doped TiO{sub 2}/PU under visible light

Energy Technology Data Exchange (ETDEWEB)

Pham, Thanh-Dong; Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr

2015-12-30

Highlights: • V doping was used to enhance the photocatalytic activity of TiO{sub 2} photocatalyst. • The enhanced TiO{sub 2} was fixed on porous polyurethane (PU) by chemical bonds. • The PU was used as a substrate to increase the adsorption ability of the photocatalyst. • V-TiO{sub 2}/PU adsorbed and photocatalytically oxidized toluene gas under visible light. • The V/TiO{sub 2} ratio of 6 wt% was optimal for enhancing the photocatalytic activity. - Abstract: In this study, V was used as a dopant to defect into the TiO{sub 2} lattice, leading to formation of Ti{sup 3+} and V{sup 4+} in the lattice. The presence of Ti{sup 3+} and V{sup 4+} introduced into the TiO{sub 2} lattice increased the electron–hole pair generation capacity and electron–hole pair separation efficiency of the TiO{sub 2}, leading to enhancement of the photocatalytic activity of the photocatalyst. Porous polyurethane (PU) was used to immobilize the V-doped TiO{sub 2} by creating chemical bonds. The use of porous substrate contributed to the increased adsorption ability of the enhanced photocatalyst, as well as expanded its application for the removal of toluene from aerosols. Under dark conditions, the V-TiO{sub 2}/PU only exhibited adsorption ability for toluene treatment in aerosol. Under visible light conditions, the V-TiO{sub 2}/PU exhibited high photocatalytic oxidation ability for the removal of toluene in aerosol. The photocatalytic oxidation ability was found to depend on the V to TiO{sub 2} ratio. The optimal V content in V/TiO{sub 2} for enhancing the photocatalytic activity of TiO{sub 2} was determined to be 6 wt%. Even under visible light irradiation, the 6% V-TiO{sub 2}/PU sample could photocatalytically remove 80% of the toluene in 200-ppmV inlet gas, while 89.3% of the removed amount was mineralized into CO{sub 2} and H{sub 2}O.

Enhanced Removal of a Human Norovirus Surrogate from Fresh Vegetables and Fruits by a Combination of Surfactants and Sanitizers▿

Science.gov (United States)

Predmore, Ashley; Li, Jianrong

2011-01-01

Fruits and vegetables are major vehicles for transmission of food-borne enteric viruses since they are easily contaminated at pre- and postharvest stages and they undergo little or no processing. However, commonly used sanitizers are relatively ineffective for removing human norovirus surrogates from fresh produce. In this study, we systematically evaluated the effectiveness of surfactants on removal of a human norovirus surrogate, murine norovirus 1 (MNV-1), from fresh produce. We showed that a panel of surfactants, including sodium dodecyl sulfate (SDS), Nonidet P-40 (NP-40), Triton X-100, and polysorbates, significantly enhanced the removal of viruses from fresh fruits and vegetables. While tap water alone and chlorine solution (200 ppm) gave only <1.2-log reductions in virus titer in all fresh produce, a solution containing 50 ppm of surfactant was able to achieve a 3-log reduction in virus titer in strawberries and an approximately 2-log reduction in virus titer in lettuce, cabbage, and raspberries. Moreover, a reduction of approximately 3 logs was observed in all the tested fresh produce after sanitization with a solution containing a combination of 50 ppm of each surfactant and 200 ppm of chlorine. Taken together, our results demonstrate that the combination of a surfactant with a commonly used sanitizer enhanced the efficiency in removing viruses from fresh produce by approximately 100 times. Since SDS is an FDA-approved food additive and polysorbates are recognized by the FDA as GRAS (generally recognized as safe) products, implementation of this novel sanitization strategy would be a feasible approach for efficient reduction of the virus load in fresh produce. PMID:21622782

Enhanced selective removal of Cu(II) from aqueous solution by novel polyethylenimine-functionalized ion imprinted hydrogel: Behaviors and mechanisms

Energy Technology Data Exchange (ETDEWEB)

Wang, Jingjing [State Key Laboratory of Pollutant Control and Resource Reuse, Nanjing 210023 (China); School of the Environment, Nanjing University, Nanjing 210023 (China); Li, Zhengkui, E-mail: zhkuili@nju.edu.cn [State Key Laboratory of Pollutant Control and Resource Reuse, Nanjing 210023 (China); School of the Environment, Nanjing University, Nanjing 210023 (China)

2015-12-30

Highlights: • A novel ion-imprinted poly(polyethylenimine/hydroxyethyl acrylate) hydrogel was synthesized. • The prepared hydrogel enhanced the selectivity of Cu(II) removal. • The material had high adsorption capacity and excellent regeneration property for copper. • The adsorption mechanism was the chelate interaction between functional groups and Cu(II) ions. - Abstract: A novel polyethylenimine-functionalized ion-imprinted hydrogel (Cu(II)-p(PEI/HEA)) was newly synthesized by {sup 60}Co-γ-induced polymerization for the selective removal of Cu(II) from aqueous solution. The adsorption performances including the adsorption capacity and selectivity of the novel hydrogel were much better than those of similar adsorbents reported. The hydrogel was characterized via scanning electron microscope, transmission electron microscopy, Fourier transform infrared spectra, thermal gravimetric analysis and X-ray photoelectron spectroscopy to determine the structure and mechanisms. The adsorption process was pH and temperature sensitive, better fitted to pseudo-second-order equation, and was Langmuir monolayer adsorption. The maximum adsorption capacity for Cu(II) was 40.00 mg/g. The selectivity coefficients of ion-imprinted hydrogel for Cu(II)/Pb(II), Cu(II)/Cd(II) and Cu(II)/Ni(II) were 55.09, 107.47 and 63.12, respectively, which were 3.93, 4.25 and 3.53 times greater than those of non-imprinted hydrogel, respectively. Moreover, the adsorption capacity of Cu(II)-p(PEI/HEA) could still keep more than 85% after four adsorption–desorption cycles. Because of such enhanced selective removal performance and excellent regeneration property, Cu(II)-p(PEI/HEA) is a promising adsorbent for the selective removal of copper ions from wastewater.

Re-use of winery wastewaters for biological nutrient removal.

Science.gov (United States)

Rodríguez, L; Villaseñor, J; Buendía, I M; Fernández, F J

2007-01-01

The aim of this study was to evaluate the feasibility of the re-use of the winery wastewater to enhance the biological nutrient removal (BNR) process. In batch experiments it was observed that the addition of winery wastewater mainly enhanced the nitrogen removal process because of the high denitrification potential (DNP), of about 130 mg N/g COD, of the contained substrates. This value is very similar to that obtained by using pure organic substrates such as acetate. The addition of winery wastewater did not significantly affect either phosphorus or COD removal processes. Based on the experimental results obtained, the optimum dosage to remove each mg of N-NO3 was determined, being a value of 6.7 mg COD/mg N-NO3. Because of the good properties of the winery wastewater to enhance the nitrogen removal, the viability of its continuous addition in an activated sludge pilot-scale plant for BNR was studied. Dosing the winery wastewater to the pilot plant a significant increase in the nitrogen removal was detected, from 58 to 75%. The COD removal was slightly increased, from 89 to 95%, and the phosphorus removal remained constant.

Application of bifunctional Saccharomyces cerevisiae to remove lead(II) and cadmium(II) in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Zhang Yunsong [Department of Chemistry, College of Life and Science, Sichuan Agricultural University, Yaan 625014 (China); Liu Weiguo [Agronomy College, Sichuan Agricultural University, Wenjiang 611130 (China); Zhang Li; Wang Meng [Department of Chemistry, College of Life and Science, Sichuan Agricultural University, Yaan 625014 (China); Zhao Maojun, E-mail: yaanyunsong@yahoo.com.cn [Department of Chemistry, College of Life and Science, Sichuan Agricultural University, Yaan 625014 (China)

2011-09-15

A magnetic adsorbent, EDTAD-functionalized Saccharomyces cerevisiae, has been synthesized to behave as an adsorbent for heavy metal ions by adjusting the pH value of the aqueous solution to make carboxyl and amino groups protonic or non-protonic. The bifunctional Saccharomyces cerevisiae (EMS) were used to remove lead(II) and cadmium(II) in solution in a batch system. The results showed that the adsorption capacity of the EMS for the heavy metal ions increased with increasing solution pH, and the maximum adsorption capacity (88.16 mg/g for Pb{sup 2+}, 40.72 mg/g for Cd{sup 2+}) at 10 deg. C was found to occur at pH 5.5 and 6.0, respectively. The adsorption process followed the Langmuir isotherm model. The regeneration experiments revealed that the EMS could be successfully reused.

Startup and long term operation of enhanced biological phosphorus removal in continuous-flow reactor with granules.

Science.gov (United States)

Li, Dong; Lv, Yufeng; Zeng, Huiping; Zhang, Jie

2016-07-01

The startup and long term operation of enhanced biological phosphorus removal (EBPR) in a continuous-flow reactor (CFR) with granules were investigated in this study. Through reducing the settling time from 9min to 3min gradually, the startup of EBPR in a CFR with granules was successfully realized in 16days. Under continuous-flow operation, the granules with good phosphorus and COD removal performance were stably operated for more than 6months. And the granules were characterized with particle size of around 960μm, loose structure and good settling ability. During the startup phase, polysaccharides (PS) was secreted excessively by microorganisms to resist the influence from the variation of operational mode. Results of relative quantitative PCR indicated that granules dominated by polyphosphate-accumulating organisms (PAOs) were easier accumulated in the CFR because more excellent settling ability was needed in the system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Superconducting magnets and leads thereto

International Nuclear Information System (INIS)

Biltcliffe, M.N.; Hanley, P.E.; McKinnon, J.B.; Wheatley, R.W.

1975-01-01

The magnet described comprises a cryostat containing a superconducting coil for the generation of a magnetic field, with a short-circuiting superconducting link connected across the coil, and electrical leads extending through the cryostat to the coil; these leads are provided with joints within the cryostat to enable them to be detached from the coil and removed from the cryostat without interrupting the current through the coil, thus reducing heat conduction to the cryostat through the leads. The joints are arranged so that the leads can be readily detached and re-attached to the coil from outside the cryostat. Gas-tight seals are provided where the leads pass through the outer wall of the cryostat, with caps that can be secured after removal of the leads. This kind of magnet can provide a stable magnetic field continuously over long periods, such as is required in nuclear magnetic resonance spectrometers. (U.K.)

Enhancement of nutrient removal from swine wastewater digestate coupled to biogas purification by microalgae Scenedesmus spp.

Science.gov (United States)

Prandini, Jean Michel; da Silva, Márcio Luís Busi; Mezzari, Melissa Paola; Pirolli, Mateus; Michelon, William; Soares, Hugo Moreira

2016-02-01

This work investigated the effects of swine wastewater-derived biogas on microalgae biomass production and nutrient removal rates from piggery wastewater concomitantly with biogas filtration. Photobioreactors with dominant Scenedesmus spp. were prepared using non-sterile digestate and exposed to different photoperiods. In the presence of biogas and autotrophic conditions microalgae yield of 1.1±0.2 g L(-1) (growth rate of 141.8±3.5 mg L(-1) d(-1)) was obtained leading to faster N-NH3 and P-PO4(3-) assimilation rate of 21.2±1.2 and 3.5±2.5 mg L(-1) d(-1), respectively. H2S up to 3000 ppmv was not inhibitory and completely removed. Maximum CO2 assimilation of 219±4.8 mg L(-1) d(-1) was achieved. Biological consumption of CH4 up to 18% v/v was verified. O2 up to 22% v/v was controlled by adding acetate to exacerbate oxygen demand by microorganisms. Microalgae-based wastewater treatment coupled to biogas purification accelerates nutrient removal concomitantly producing valuable biomass and biomethane. Copyright © 2015 Elsevier Ltd. All rights reserved.

Enhanced WWTP effluent organic matter removal in hybrid ozonation-coagulation (HOC) process catalyzed by Al-based coagulant

Energy Technology Data Exchange (ETDEWEB)

Jin, Xin [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Jin, Pengkang, E-mail: pkjin@hotmail.com [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Hou, Rui [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Yang, Lei [Department of Materials Science and Engineering, Monash University, Clayton, VIC, 3800 (Australia); Wang, Xiaochang C., E-mail: xcwang@xauat.edu.cn [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China)

2017-04-05

Highlights: • A novel HOC process was firstly put forward to apply in wastewater reclamation. • Interactions between ozone and Al-based coagulants was found in the HOC process. • Ozonation can be catalyzed and enhanced by Al-based coagulants in the HOC process. • HOC process showed better organics removal than pre-ozonation-coagulation process. - Abstract: A novel hybrid ozonation-coagulation (HOC) process was developed for application in wastewater reclamation. In this process, ozonation and coagulation occurred simultaneously within a single unit. Compared with the conventional pre-ozonation-coagulation process, the HOC process exhibited much better performance in removing dissolved organic matters. In particular, the maximal organic matters removal efficiency was obtained at the ozone dosage of 1 mgO{sub 3}/mg DOC at each pH value (pH 5, 7 and 9). In order to interpret the mechanism of the HOC process, ozone decomposition was monitored. The results indicated that ozone decomposed much faster in the HOC process. Moreover, by using the reagent of O{sub 3}-resistant hydroxyl radical (·OH) probe compound, para-chlorobenzoic acid (pCBA), and electron paramagnetic resonance (EPR) analysis, it was observed that the HOC process generated higher content of ·OH compared with pre-ozonation process. This indicates that the ·OH oxidation reaction as the key step can be catalyzed and enhanced by Al-based coagulants and their hydrolyzed products in this developed process. Thus, based on the catalytic effects of Al-based coagulants on ozonation, the HOC process provides a promising alternative to the conventional technology for wastewater reclamation in terms of higher efficiency.

Fe/Ti co-pillared clay for enhanced arsenite removal and photo oxidation under UV irradiation

Energy Technology Data Exchange (ETDEWEB)

Li, Yuan [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Guang Dong Electric Power Design Institute, China Energy Engineering Group Co. Ltd., Guangzhou 510663 (China); Cai, Xiaojiao [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Guo, Jingwei [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); The 718th Research Institute of CSIC, Handan 056027 (China); Zhou, Shimin [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Na, Ping, E-mail: naping@tju.edu.cn [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China)

2015-01-01

Graphical abstract: - Highlights: • An iron and titanium co-pillared montmorillonite (Fe-Ti/MMT) was synthesized for arsenite removal. • Variety of characterization results indicated that Fe and Ti species were pillared in MMT. • A possible mechanism of arsenite adsorption/oxidation with UV light was established. • The participation of Fe component can promote the process of photocatalytic oxidation in Fe-Ti/MMT + As(III) system. • Fe-Ti/MMT can function as both photocatalyst and adsorbent for arsenite removal. - Abstract: A series of iron and titanium co-pillared montmorillonites (Fe-Ti/MMT) were prepared using hydrolysis of inserted titanium and different iron content in montmorillonite (MMT). The Fe-Ti/MMT were characterized by X-ray fluorescence, N{sub 2} adsorption and desorption, X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM), confirming the effective insertion of Fe species and TiO{sub 2} in the MMT. The Fe-Ti/MMT was used to remove arsenite (As(III)) from aqueous solutions under different conditions. The result of As(III) adsorption under UV irradiation showed that the photo activity can be enhanced by incorporating Fe and Ti in MMT. Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analysis indicated that the hydroxyl groups bonded to metal oxide (M–OH) played an important role in the adsorption of As(III)

Continuous Fixed-Bed Column Study and Adsorption Modeling: Removal of Lead Ion from Aqueous Solution by Charcoal Originated from Chemical Carbonization of Rubber Wood Sawdust

Directory of Open Access Journals (Sweden)

Swarup Biswas

2015-01-01

Full Text Available The efficiency of chemically carbonized rubber wood sawdust for the removal of lead ion from the aqueous stream was investigated by column process. Chemically carbonized rubber wood sawdust was prepared by treating the sawdust with H2SO4 and HNO3. Maximum removal of lead ion in column process was found as 38.56 mg/g. The effects of operating parameters such as flow rate, bed depth, concentration, and pH were studied in column mode. Experimental data confirmed that the adsorption capacity increased with the increasing inlet concentration and bed depth and decreased with increasing flow rate. Thomas, Yoon-Nelson, and Adams-Bohart models were used to analyze the column experimental data and the relationship between operating parameters. Chemically carbonized rubber wood sawdust was characterized by using Fourier transform infrared spectroscopy. Scanning electron microscope was also utilized for morphological analysis of the adsorbent. Furthermore X-ray fluorescence spectrum analysis and energy dispersive X-ray spectroscopy were also used for the confirmation of lead adsorption process.

Adsorbent material based on passion-fruit wastes to remove lead (Pb), chromium (Cr) and copper (Cu) from metal-contaminated waters

Science.gov (United States)

Campos-Flores, Gaby; Castillo-Herrera, Alberto; Gurreonero-Fernández, Julio; Obeso-Obando, Aída; Díaz-Silva, Valeria; Vejarano, Ricardo

2018-04-01

The aim of the present work was to evaluate the feasibility of passion-fruit shell (PFS) biomass as adsorbent material to remove heavy metals from contaminated waters. Model mediums were used, which were composed of distilled water and the respective metal: lead (Pb), chromium (Cr) and copper (Cu), with a dose of 10g of dry PFSbiomass per liter of medium. The residual concentration of each metal was determined by Atomic Absorption Spectrophotometry (AAS). A good adsorption capacity was exhibited by this agro industrial waste, achieving removal levels of 96,93 and 82% for Pb, Cr and Cu, respectively. In addition, the results obtained showed an adequate fit to the Freundlich model (R2 > 0.91), on the basis of which, the following values of adsorption capacity (k: 1.7057, 0.6784, 0.3302) and adsorption intensity (n: 0.6869, 2.3474, 1.0499), for Pb, Cr and Cu respectively, were obtained. Our results suggest that Pb, Cr and Cu ions can be removed by more than 80% by using this agro industrial waste, which with a minimum treatment could be used as an adsorbent material in the treatment of metal-contaminated waters.

Enhanced coagulation with powdered activated carbon or MIEX secondary treatment: a comparison of disinfection by-product formation and precursor removal.

Science.gov (United States)

Watson, Kalinda; Farré, Maria José; Knight, Nicole

2015-01-01

The removal of both organic and inorganic disinfection by-product (DBP) precursors prior to disinfection is important in mitigating DBP formation, with halide removal being particularly important in salinity-impacted water sources. A matrix of waters of variable alkalinity, halide concentration and dissolved organic carbon (DOC) concentration were treated with enhanced coagulation (EC) followed by anion exchange (MIEX resin) or powdered activated carbon (PAC) and the subsequent disinfection by-product formation potentials (DBP-FPs) assessed and compared to DBP-FPs for untreated samples. Halide and DOC removal were also monitored for both treatment processes. Bromide and iodide adsorption by MIEX treatment ranged from 0 to 53% and 4-78%, respectively. As expected, EC and PAC treatments did not remove halides. DOC removal by EC/PAC was 70 ± 10%, while EC/MIEX enabled a DOC removal of 66 ± 12%. Despite the halide removals achieved by MIEX, increases in brominated disinfection by-product (Br-DBP) formation were observed relative to untreated samples, when favourable Br:DOC ratios were created by the treatment. However, the increases in formation were less than what was observed for the EC/PAC treated waters, which caused large increases in Br-DBP formation when high Br-DBP-forming water quality conditions occurred. The formation potential of fully chlorinated DBPs decreased after treatment in all cases.

Aerosol removal due to precipitation and wind forcings in Milan urban area

Science.gov (United States)

Cugerone, Katia; De Michele, Carlo; Ghezzi, Antonio; Gianelle, Vorne

2018-01-01

Air pollution represents a critical issue in Milan urban area (Northern Italy). Here, the levels of fine particles increase, overcoming the legal limits, mostly in wintertime, due to favourable calm weather conditions and large heating and vehicular traffic emissions. The main goal of this work is to quantify the aerosol removal effect due to precipitation at the ground. At first, the scavenging coefficients have been calculated for aerosol particles with diameter between 0.25 and 3 μm. The average values of this coefficient vary between 2 ×10-5 and 5 ×10-5 s-1. Then, the aerosol removal induced separately by precipitation and wind have been compared through the introduction of a removal index. As a matter of fact, while precipitation leads to a proper wet scavenging of the particles from the atmosphere, high wind speeds cause enhanced particle dispersion and dilution, that locally bring to a tangible decrease of aerosol particles' number. The removal triggered by these two forcings showed comparable average values, but different trends. The removal efficiency of precipitation lightly increases with the increase of particle diameters and vice versa happens with strong winds.

Fe-Mn bi-metallic oxides loaded on granular activated carbon to enhance dye removal by catalytic ozonation.

Science.gov (United States)

Tang, Shoufeng; Yuan, Deling; Zhang, Qi; Liu, Yameng; Zhang, Qi; Liu, Zhengquan; Huang, Haiming

2016-09-01

A Fe-Mn bi-metallic oxide supported on granular activated carbon (Fe-Mn GAC) has been fabricated by an impregnation-desiccation method and tested in the catalytic ozonation of methyl orange (MO) degradation and mineralization. X-ray diffraction, scanning electron microscopy, and Fourier transform infrared spectroscopy characterizations revealed that Fe-Mn oxides were successfully loaded and uniformly distributed on the GAC, and nitrogen adsorption isotherms showed that the supported GAC retained a large surface area and a high pore volume compared with the pristine GAC. The catalytic activity was systematically assessed by monitoring the MO removal efficiencies at different operational parameters, such as catalyst dosage, initial solution pH, and ozone flow rate. The Fe-Mn GAC exhibited better catalytic activity relative to ozone alone and GAC alone, improving the TOC removal by 24.5 and 11.5 % and COD removal by 13.6 and 7.3 %, respectively. The reusability of the hybrid was examined over five consecutive cyclic treatments. The Fe-Mn GAC catalytic activity was only a slight loss in the cycles, showing good stability. The addition of Na2CO3 as hydroxyl radicals (•OH) scavengers proved that the catalytic ozonation mechanism was the enhanced generation of •OH by the Fe-Mn GAC. The above results render the Fe-Mn GAC an industrially promising candidate for catalytic ozonation of dye contaminant removal.

Ligand removal and photo-activation of CsPbBr3 quantum dots for enhanced optoelectronic devices.

Science.gov (United States)

Moyen, Eric; Kanwat, Anil; Cho, Sinyoung; Jun, Haeyeon; Aad, Roy; Jang, Jin

2018-05-10

Perovskite quantum dots have recently emerged as a promising light source for optoelectronic applications. However, integrating them into devices while preserving their outstanding optical properties remains challenging. Due to their ionic nature, perovskite quantum dots are extremely sensitive and degrade on applying the simplest processes. To maintain their colloidal stability, they are surrounded by organic ligands; these prevent efficient charge carrier injection in devices and have to be removed. Here we report on a simple method, where a moderate thermal process followed by exposure to UV in air can efficiently remove ligands and increase the photo-luminescence of the room temperature synthesized perovskite quantum dot thin films. Annealing is accompanied by a red shift of the emission wavelength, usually attributed to the coalescence and irreversible degradation of the quantum dots. We show that it is actually related to the relaxation of the quantum dots upon the ligand removal, without the creation of non-radiative recombining defects. The quantum dot surface, as devoid of ligands, is subsequently photo-oxidized and smoothened upon exposure to UV in air, which drastically enhances their photo-luminescence. This adequate combination of treatments improves by more than an order of magnitude the performances of perovskite quantum dot light emitting diodes.

Removal of lead(II) by adsorption using treated granular activated carbon: batch and column studies.

Science.gov (United States)

Goel, Jyotsna; Kadirvelu, Krishna; Rajagopal, Chitra; Kumar Garg, Vinod

2005-10-17

In the present study, a deeper understanding of adsorption behavior of Pb(II) from aqueous systems onto activated carbon and treated activated carbon has been attempted via static and column mode studies under various conditions. It probes mainly two adsorbents that is, activated carbon (AC) and modified activated carbon (AC-S). Characterization of both the adsorbents was one of the key focal areas of the present study. This has shown a clear change or demarcation in the various physical and chemical properties of the modified adsorbent from its precursor activated carbon. Both the adsorbents are subjected to static mode adsorption studies and then after a comparison based on isotherm analysis; more efficient adsorbent is screened for column mode adsorption studies. The lead removal increased for sample of treated carbon. The extent of Pb(II) removal was found to be higher in the treated activated carbon. The aim of carrying out the continuous-flow studies was to assess the effect of various process variables, viz., of bed height, hydraulic loading rate and initial feed concentration on breakthrough time and adsorption capacity. This has helped in ascertaining the practical applicability of the adsorbent. Breakthrough curves were plotted for the adsorption of lead on the adsorbent using continuous-flow column operation by varying different operating parameters like hydraulic loading rate (3.0-10.5 m3/(hm2)), bed height (0.3-0.5 m) and feed concentrations (2.0-6.0 mg/l). At the end, an attempt has also been made to model the data generated from column studies using the empirical relationship based on Bohart-Adams model. This model has provided an objective framework to the subjective interpretation of the adsorption system and the model constant obtained here can be used to achieve the ultimate objective of our study that is, up scaling and designing of adsorption process at the pilot plant scale level. AC-S column regeneration using 0.5 and 1.0M concentration of

Enhanced accumulation of copper and lead in amaranth (Amaranthus paniculatus), Indian mustard (Brassica juncea) and sunflower (Helianthus annuus).

Science.gov (United States)

Rahman, Motior M; Azirun, Sofian M; Boyce, Amru N

2013-01-01

Soil contamination by copper (Cu) and lead (Pb) is a widespread environmental problem. For phytoextraction to be successful and viable in environmental remediation, strategies that can improve plant uptake must be identified. In the present study we investigated the use of nitrogen (N) fertilizer as an efficient way to enhance accumulation of Cu and Pb from contaminated industrial soils into amaranth, Indian mustard and sunflower. Plants were grown in a greenhouse and fertilized with N fertilizer at rates of 0, 190 and 380 mg kg⁻¹ soil. Shoots, roots and total accumulation of Cu and Pb, transfer factor (TF), translocation index were assessed to evaluate the transport and translocation ability of tested plants. Addition of N fertilizer acidified the industrial soil and caused the pH to decrease to 5.5 from an initial pH of 6.9. Industrial soil amended with N fertilizer resulted in the highest accumulation of Pb and Cu (for Pb 10.1-15.5 mg kg⁻¹, for Cu 11.6-16.8 mg kg⁻¹) in the shoots, which was two to four folds higher relative to the concentration in roots in all the three plants used. Sunflower removed significantly higher Pb (50-54%) and Cu (34-38%) followed by amaranth and Indian mustard from industrial soils with the application of N fertilizer. The TF was Sunflower is the best plant species to carry out phytoextraction of Pb and Cu. In contrast, Pb and Cu removal by Indian mustard and amaranth shows great potential as quick and short duration vegetable crops. The results suggest that the application of N fertilizer in contaminated industrial soil is an effective amendment for the phytoextraction of Pb and Cu from contaminated industrial soils.

Apatite and Chitin Amendments Promote Microbial Activity and Augment Metal Removal in Marine Sediments

Science.gov (United States)

2013-07-01

remedial history at met- als contaminated soils sites [10,13,14]. Apatite’s use in sediment remediation is more recent [15]. The DoD (Navy) is currently...ABSTRACT In situ amendments are a promising approach to enhance removal of metal contaminants from diverse environments including soil , groundwater... Soil Treatments to Reduce the Phyto and Bioavailability of Lead, Zinc, and Cadmium ,” Journal of Environmental Quality, Vol. 33, No. 2, 2004, pp. 522

One pot synthesis of CdS/TiO{sub 2} hetero-nanostructures for enhanced H{sub 2} production from water and removal of pollutants from aqueous streams

Energy Technology Data Exchange (ETDEWEB)

Mani, A. Daya; Subrahmanyam, Ch., E-mail: csubbu@iith.ac.in

2016-01-15

Highlights: • Novel one pot synthesis of CdS/TiO{sub 2} hetero nanostructures by combustion synthesis. • Excellent visible light photocatalytic activity for H{sub 2} production from water. • Enhanced activity for the removal of Cr(VI) from aqueous streams. - Abstract: To achieve more effective coupling of cadmium sulfide (CdS) to the TiO{sub 2}, single step synthesis of CdS/TiO{sub 2} composites is advantageous. In the present study a novel one pot synthesis of several CdS/TiO{sub 2} hetero-nanostructures was explored through combustion technique. As the process involves the simultaneous nucleation of CdS and TiO{sub 2} it leads to the proper connectivity between the constituent materials. All the catalysts were characterized by using several techniques and the excellent visible light activity of the composites has been asserted by the H{sub 2} production from water containing sacrificial reagents, removal of methylene blue and Cr(VI) from aqueous streams. Therefore the present synthetic strategy which is devoid of using molecular linker at interface is more suitable for solar applications, which require faster rates of electron transfer at the hetero junctions.

Fast adsorption kinetics of highly dispersed ultrafine nickel/carbon nanoparticles for organic dye removal

Science.gov (United States)

Kim, Taek-Seung; Song, Hee Jo; Dar, Mushtaq Ahmad; Lee, Hack-Jun; Kim, Dong-Wan

2018-05-01

Magnetic metal/carbon nano-materials are attractive for pollutant adsorption and removal. In this study, ultrafine nickel/carbon nanoparticles are successfully prepared via electrical wire explosion processing in ethanol media for the elimination of pollutant organic dyes such as Rhodamine B and methylene blue in aqueous solutions. High specific surface areas originating from both the nano-sized particles and the existence of carbon on the surface of Ni nanoparticles enhance dye adsorption capacity. In addition to this, the excellent dispersity of Ni/C nanoparticles in aqueous dye solutions leads to superior adsorption rates. The adsorption kinetics for the removal of organic dyes by Ni/C nanoparticles agree with a pseudo-second-order model and follow Freundlich adsorption isotherm behavior.

Enhanced Leads and Appointment System

Data.gov (United States)

Social Security Administration — The data asset contains information on current or upcoming appointments, individuals who will be attending the appointment, potential intent to file a claim (lead),...

Image processing on the image with pixel noise bits removed

Science.gov (United States)

Chuang, Keh-Shih; Wu, Christine

1992-06-01

Our previous studies used statistical methods to assess the noise level in digital images of various radiological modalities. We separated the pixel data into signal bits and noise bits and demonstrated visually that the removal of the noise bits does not affect the image quality. In this paper we apply image enhancement techniques on noise-bits-removed images and demonstrate that the removal of noise bits has no effect on the image property. The image processing techniques used are gray-level look up table transformation, Sobel edge detector, and 3-D surface display. Preliminary results show no noticeable difference between original image and noise bits removed image using look up table operation and Sobel edge enhancement. There is a slight enhancement of the slicing artifact in the 3-D surface display of the noise bits removed image.

Novel porous fly-ash containing geopolymer monoliths for lead adsorption from wastewaters

Energy Technology Data Exchange (ETDEWEB)

Novais, Rui M., E-mail: ruimnovais@ua.pt; Buruberri, L.H.; Seabra, M.P.; Labrincha, J.A.

2016-11-15

Highlights: • Porous fly ash containing-geopolymer monoliths for lead adsorption were developed. • Geopolymers’ porosity and pH of the ion solution controls the adsorption capacity. • Lead adsorption by the geopolymer monoliths up to 6.34 mg/g was observed. • These novel adsorbents can be used in packed beds that are easily collected. • The reuse of biomass fly ash wastes as raw material ensures waste valorization. - Abstract: In this study novel porous biomass fly ash-containing geopolymer monoliths were produced using a simple and flexible procedure. Geopolymers exhibiting distinct total porosities (ranging from 41.0 to 78.4%) and low apparent density (between 1.21 and 0.44 g/cm{sup 3}) were fabricated. Afterwards, the possibility of using these innovative materials as lead adsorbents under distinct conditions was evaluated. Results demonstrate that the geopolymers’ porosity and the pH of the ion solution strongly affect the lead adsorption capacity. Lead adsorption by the geopolymer monoliths ranged between 0.95 and 6.34 mg{sub lead}/g{sub geopolymer}. More porous geopolymers presented better lead removal efficiency, while higher pH in the solution reduced their removal ability, since metal precipitation is enhanced. These novel geopolymeric monoliths can be used in packed beds that are easily collected when exhausted, which is a major advantage in comparison with the use of powdered adsorbents. Furthermore, their production encompasses the reuse of biomass fly-ash, mitigating the environmental impact associated with this waste disposal, while decreasing the adsorbents production costs.

Lead and Drinking Water from Private Wells

Science.gov (United States)

... type=”submit” value=”Submit” /> Healthy Water Home Lead and Drinking Water from Private Wells Recommend on ... remove lead from my drinking water? What is lead? Lead is a naturally occurring bluish-gray metal ...

Apparatus and methods for purifying lead

Science.gov (United States)

Tunison, Harmon M.

2016-01-12

Disclosed is an exemplary method of purifying lead which includes the steps of placing lead and a fluoride salt blend in a container; forming a first fluid of molten lead at a first temperature; forming a second fluid of the molten fluoride salt blend at a second temperature higher than the first temperature; mixing the first fluid and the second fluid together; separating the two fluids; solidifying the molten fluoride salt blend at a temperature above a melting point of the lead; and removing the molten lead from the container. In certain exemplary methods the molten lead is removed from the container by decanting. In still other exemplary methods the molten salt blend is a Lewis base fluoride eutectic salt blend, and in yet other exemplary methods the molten salt blend contains sodium fluoride, lithium fluoride, and potassium fluoride.

Reversible surface binding of cadmium and lead by lactic acid and bifidobacteria.

Science.gov (United States)

Teemu, Halttunen; Seppo, Salminen; Jussi, Meriluoto; Raija, Tahvonen; Kalle, Lertola

2008-07-15

Extensive cadmium and lead contamination of water has been reported to occur locally as a result of human activities. Lactic acid bacteria have been reported to remove cadmium and lead from water. The aim of this work was to clarify the mechanisms of cadmium and lead removal from water. In addition, the effect of other metals, reversibility of binding and recyclability of the biomass was assessed. Based on our earlier data, the two most promising lactic acid bacteria, Lactobacillus fermentum ME3 and Bifidobacterium longum 46, were selected for these experiments. The results showed that the presence of other cationic metals and blocking of carboxyl and phosphoryl groups reduced cadmium and lead removal. These results suggest involvement of electrostatic interactions in cadmium and lead removal, and support our earlier findings. Transmission electron micrographs showed large deposits of lead on the bacterial surface suggesting formation of metallic lead precipitates. Both cadmium and lead removal were reversible processes established by full recovery of removed metal after desorption with dilute solutions of EDTA and HNO(3). Resorption capacity of both biomasses tested was reduced after regeneration with 10 mM EDTA and 15 mM HNO(3). Taken together, the results suggest involvement of several reversible mechanisms such as ion exchange and precipitation in cadmium and lead binding by lactic acid bacteria. The results show that specific lactic acid bacteria have the potential for removal of cadmium and lead from water although reduction in resorption capacity after regeneration of the biomass may form a problem. Since the studies so far have mainly focused on removal of single metals from pure water, metal removal in conditions of natural waters should be assessed in further experiments.

Use of constructed wetland for the removal of heavy metals from industrial wastewater.

Science.gov (United States)

Khan, Sardar; Ahmad, Irshad; Shah, M Tahir; Rehman, Shafiqur; Khaliq, Abdul

2009-08-01

This study was conducted to investigate the effectiveness of a continuous free surface flow wetland for removal of heavy metals from industrial wastewater, in Gadoon Amazai Industrial Estate (GAIE), Swabi, Pakistan. Industrial wastewater samples were collected from the in-let, out-let and all cells of the constructed wetland (CW) and analyzed for heavy metals such as lead (Pb), cadmium (Cd), iron (Fe), nickel (Ni), chromium (Cr) and copper (Cu) using standard methods. Similarly, samples of aquatic macrophytes and sediments were also analyzed for selected heavy metals. Results indicate that the removal efficiencies of the CW for Pb, Cd, Fe, Ni, Cr, and Cu were 50%, 91.9%, 74.1%, 40.9%, 89%, and 48.3%, respectively. Furthermore, the performance of the CW was efficient enough to remove the heavy metals, particularly Cd, Fe, and Cu, from the industrial wastewater fed to it. However, it is suggested that the metal removal efficiency of the CW can be further enhanced by using proper management of vegetation and area expansion of the present CW.

Stabilized chitosan/Fe(0)-nanoparticle beads to remove heavy metals from polluted sediments.

Science.gov (United States)

Liu, T; Sun, Y; Wang, Z L

2016-01-01

Sediment contamination by heavy metals has become a widespread problem that can affect the normal behaviors of rivers and lakes. After chitosan/Fe(0)-nanoparticles (CS-NZVI) beads were cross-linked with glutaraldehyde (GLA), their mechanical strength, stability and separation efficiency from the sediment were obviously improved. Moreover, the average aperture size of GLA-CS-NZVI beads was 20.6 μm and NZVI particles were nearly spherical in shape with a mean diameter of 40.2 nm. In addition, the pH showed an insignificant effect on the removal rates from the sediment. Due to the dissolution of metals species into aqueous solutions as an introduction of the salt, the removal rates of all heavy metals from the sediment were increased with an increase of the salinity. The competitive adsorption of heavy metals between the sediment particles and GLA-CS-NZVI beads became stronger as the sediment particles became smaller, leading to decreased removal rates. Therefore, the removal efficiency could be enhanced by optimizing experimental conditions and choosing appropriate materials for the target contaminants.

Elliptical Leaf Spring Shock and Vibration Mounts with Enhanced Damping and Energy Dissipation Capabilities Using Lead Spring

Directory of Open Access Journals (Sweden)

Moussa Leblouba

2015-01-01

Full Text Available We present an enhancement to the existing elliptical leaf spring (ELS for improved damping and energy dissipation capabilities. The ELS consists of a high tensile stainless steel elliptical leaf spring with polymer or rubber compound. This device is conceived as a shock and vibration isolator for equipment and lightweight structures. The enhancement to the ELS consists of a lead spring plugged vertically between the leaves (referred to as lead-rubber elliptical leaf spring (LRELS. The lead is shown to produce hysteretic damping under plastic deformations. The LRELS isolator is shown to exhibit nonlinear hysteretic behavior. In both horizontal directions, the LRELS showed symmetrical rate independent behavior but undergoes stiffening behavior under large displacements. However, in the vertical direction, the LRELS behavior is asymmetric, exhibiting softening behavior in compression and stiffening behavior in tension. Mathematical models based on the Bouc-Wen model, describing the hysteretic behavior of the proposed isolator, are developed and numerically calibrated using a series of finite element analyses. The LRELS is found to be effective in the in-plane and vertical directions. The improved damping and energy dissipation of the LRELS is provided from the hysteretic damping of the lead spring.

Enhanced removal of nitrate from water using amine-grafted agricultural wastes

Energy Technology Data Exchange (ETDEWEB)

Kalaruban, Mahatheva; Loganathan, Paripurnanda [Faculty of Engineering, University of Technology Sydney (UTS), P.O. Box 123, Broadway, NSW 2007 (Australia); Shim, W.G. [Faculty of Engineering, University of Technology Sydney (UTS), P.O. Box 123, Broadway, NSW 2007 (Australia); Department of Polymer Science and Engineering, Sunchon National University, 255 Jungang-ro, Suncheon, Jeollanam-do (Korea, Republic of); Kandasamy, Jaya; Ngo, H.H. [Faculty of Engineering, University of Technology Sydney (UTS), P.O. Box 123, Broadway, NSW 2007 (Australia); Vigneswaran, Saravanamuthu, E-mail: s.vigneswaran@uts.edu.au [Faculty of Engineering, University of Technology Sydney (UTS), P.O. Box 123, Broadway, NSW 2007 (Australia)

2016-09-15

Adsorption using low-cost adsorbents is a favourable water treatment method for the removal of water contaminants. In this study the enhanced removal of nitrate, a contaminant at elevated concentration affecting human health and causing eutrophication of water, was tested using chemically modified agricultural wastes as adsorbents. Batch and fixed-bed adsorption studies were performed on corn cob and coconut copra that were surface modified by amine-grafting to increase the surface positive charges. The Langmuir nitrate adsorption capacities (mg N/g) were 49.9 and 59.0 for the amine-grafted (AG) corn cob and coconut copra, respectively at pH 6.5 and ionic strength 1 × 10{sup −3} M NaCl. These values are higher than those of many commercially available anion exchange resins. Fixed-bed (15-cm height) adsorption capacities (mg N/g) calculated from the breakthrough curves were 15.3 and 18.6 for AG corn cob and AG coconut copra, respectively, for an influent nitrate concentration 20 mg N/L at a flow velocity 5 m/h. Nitrate adsorption decreased in the presence of sulphate, phosphate and chloride, with sulphate being the most competitive anion. The Thomas model fitted well to the fixed-bed adsorption data from four repeated adsorption/desorption cycles. Plug-flow model fitted well to the data from only the first cycle. - Highlights: • Ground coconut copra and corn cob particles surfaces are readily amine-grafted. • Amine-grafting reversed the particles' surface charge from negative to positive. • Amine-grafting of the waste particles increased nitrate adsorption capacity. • Nitrate adsorption capacity reduced by co-ions; sulphate > chloride > phosphate. • Fixed-bed nitrate adsorption data fitted well to Thomas and plug-flow models.

Enhanced removal of nitrate from water using amine-grafted agricultural wastes

International Nuclear Information System (INIS)

Kalaruban, Mahatheva; Loganathan, Paripurnanda; Shim, W.G.; Kandasamy, Jaya; Ngo, H.H.; Vigneswaran, Saravanamuthu

2016-01-01

Adsorption using low-cost adsorbents is a favourable water treatment method for the removal of water contaminants. In this study the enhanced removal of nitrate, a contaminant at elevated concentration affecting human health and causing eutrophication of water, was tested using chemically modified agricultural wastes as adsorbents. Batch and fixed-bed adsorption studies were performed on corn cob and coconut copra that were surface modified by amine-grafting to increase the surface positive charges. The Langmuir nitrate adsorption capacities (mg N/g) were 49.9 and 59.0 for the amine-grafted (AG) corn cob and coconut copra, respectively at pH 6.5 and ionic strength 1 × 10"−"3 M NaCl. These values are higher than those of many commercially available anion exchange resins. Fixed-bed (15-cm height) adsorption capacities (mg N/g) calculated from the breakthrough curves were 15.3 and 18.6 for AG corn cob and AG coconut copra, respectively, for an influent nitrate concentration 20 mg N/L at a flow velocity 5 m/h. Nitrate adsorption decreased in the presence of sulphate, phosphate and chloride, with sulphate being the most competitive anion. The Thomas model fitted well to the fixed-bed adsorption data from four repeated adsorption/desorption cycles. Plug-flow model fitted well to the data from only the first cycle. - Highlights: • Ground coconut copra and corn cob particles surfaces are readily amine-grafted. • Amine-grafting reversed the particles' surface charge from negative to positive. • Amine-grafting of the waste particles increased nitrate adsorption capacity. • Nitrate adsorption capacity reduced by co-ions; sulphate > chloride > phosphate. • Fixed-bed nitrate adsorption data fitted well to Thomas and plug-flow models.

Simultaneous inhibition of sulfate-reducing bacteria, removal of H2S and production of rhamnolipid by recombinant Pseudomonas stutzeri Rhl: Applications for microbial enhanced oil recovery.

Science.gov (United States)

Zhao, Feng; Zhou, Ji-Dong; Ma, Fang; Shi, Rong-Jiu; Han, Si-Qin; Zhang, Jie; Zhang, Ying

2016-05-01

Sulfate-reducing bacteria (SRB) are widely existed in oil production system, and its H2S product inhibits rhamnolipid producing bacteria. In-situ production of rhamnolipid is promising for microbial enhanced oil recovery. Inhibition of SRB, removal of H2S and production of rhamnolipid by recombinant Pseudomonas stutzeri Rhl were investigated. Strain Rhl can simultaneously remove S(2-) (>92%) and produce rhamnolipid (>136mg/l) under S(2-) stress below 33.3mg/l. Rhl reduced the SRB numbers from 10(9) to 10(5)cells/ml, and the production of H2S was delayed and decreased to below 2mg/l. Rhl also produced rhamnolipid and removed S(2-) under laboratory simulated oil reservoir conditions. High-throughput sequencing data demonstrated that addition of strain Rhl significantly changed the original microbial communities of oilfield production water and decreased the species and abundance of SRB. Bioaugmentation of strain Rhl in oilfield is promising for simultaneous control of SRB, removal of S(2-) and enhance oil recovery. Copyright © 2016 Elsevier Ltd. All rights reserved.

Enhancement removal of tartrazine dye using HCl-doped polyaniline and TiO2-decorated PANI particles

Science.gov (United States)

Elsayed, M. A.; Gobara, Mohamed

2016-08-01

HCl-doped polyaniline (HCl-PANI) and titanium dioxide decorated with polyaniline (TiO2-decorated PANI) with different TiO2:PANI ratios were chemically prepared and utilized for the removal of tartrazine (TZ) dye from a synthetic aqueous solution. The mechanism of preparation of the sample suggested that aniline was adsorbed on the TiO2 surface before the polymerization process took place. Samples were characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, energy dispersive x-ray spectroscopy and x-ray diffraction. The results showed that HCl-PANI and TiO2-decorated PANI have an amorphous structure. The thermal stability of the prepared samples was characterized using thermo-gravimetric (TG) analysis. HCl-PANI is stable up to 200 °C and the relative weight per cent of PANI in the TiO2-decorated PANI was 20, 25, 40 and 45%. The removal activity of TiO2-decorated PANI via TZ azo dye was investigated under UV light irradiations and compared with HCl-PANI and TiO2 particles. The results indicated the superiority of the TiO2-decorated PANI over pure HCl-PANI and TiO2. However, the excessive PANI percentage tends to form a relatively thick layer, and even aggregates on the surface of TiO2. This hinders the migration of excited electrons from the outer PANI layer to the inner TiO2 particles, which consequently leads to a decrease in the removal efficiency. A possible mechanism for the removal oxidative degradation is also mentioned.

Enhanced removal of petroleum hydrocarbons using a bioelectrochemical remediation system with pre-cultured anodes

International Nuclear Information System (INIS)

Venkidusamy, Krishnaveni; Megharaj, Mallavarapu; Marzorati, Massimo; Lockington, Robin; Naidu, Ravi

2016-01-01

Bioelectrochemical remediation (BER) systems such as microbial fuel cells (MFCs) have recently emerged as a green technology for the effective remediation of petroleum hydrocarbon contaminants (PH) coupled with simultaneous energy recovery. Recent research has shown that biofilms previously enriched for substrate degrading bacteria resulted in excellent performance in terms of substrate removal and electricity generation but the effects on hydrocarbon contaminant degradation were not examined. Here we investigate the differences between enriched biofilm anodes and freshly inoculated new anodes in diesel fed single chamber mediatorless microbial fuel cells (DMFC) using various techniques for the enhancement of PH contaminant remediation with concomitant electricity generation. An anodophilic microbial consortium previously selected for over a year through continuous culturing with a diesel concentration of about 800 mg l"−"1 and which now showed complete removal of this concentration of diesel within 30 days was compared to that of a freshly inoculated new anode MFC (showing 83.4% removal of diesel) with a simultaneous power generation of 90.81 mW/m"2 and 15.04 mW/m"2 respectively. The behaviour of pre-cultured anodes at a higher concentration of PH (8000 mg l"−"1) was also investigated. Scanning electron microscopy observation revealed a thick biofilm covering the pre-cultured anodic electrode but not the anode from the freshly inoculated MFC. High resolution imaging showed the presence of thin 60 nm diametre pilus-like projections emanating from the cells. Anodic microbial community profiling confirmed that the selection for diesel degrading exoelectrogenic bacteria had occurred. Identification of a biodegradative gene (alkB) provided strong evidence of the catabolic pathway used for diesel degradation in the DMFCs.

Enhanced removal of petroleum hydrocarbons using a bioelectrochemical remediation system with pre-cultured anodes

Energy Technology Data Exchange (ETDEWEB)

Venkidusamy, Krishnaveni [Centre for Environmental Risk Assessment and Remediation (CERAR), University of South (Australia); CRC for Contamination Assessment and Remediation of the Environment (CRCCARE), Mawson Lakes, SA5095 (Australia); Megharaj, Mallavarapu, E-mail: megh.mallavarapu@newcastle.edu.au [Centre for Environmental Risk Assessment and Remediation (CERAR), University of South (Australia); CRC for Contamination Assessment and Remediation of the Environment (CRCCARE), Mawson Lakes, SA5095 (Australia); Global Centre for Environmental Remediation, Faculty of Science and Information Technology, The University of Newcastle, Callaghan, NSW 2308 (Australia); Marzorati, Massimo [Laboratory for Microbial Ecology and Technology (LabMET), Gent University, 9000 Gent (Belgium); Lockington, Robin [Centre for Environmental Risk Assessment and Remediation (CERAR), University of South (Australia); CRC for Contamination Assessment and Remediation of the Environment (CRCCARE), Mawson Lakes, SA5095 (Australia); Naidu, Ravi [Centre for Environmental Risk Assessment and Remediation (CERAR), University of South (Australia); CRC for Contamination Assessment and Remediation of the Environment (CRCCARE), Mawson Lakes, SA5095 (Australia); Global Centre for Environmental Remediation, Faculty of Science and Information Technology, The University of Newcastle, Callaghan, NSW 2308 (Australia)

2016-01-01

Bioelectrochemical remediation (BER) systems such as microbial fuel cells (MFCs) have recently emerged as a green technology for the effective remediation of petroleum hydrocarbon contaminants (PH) coupled with simultaneous energy recovery. Recent research has shown that biofilms previously enriched for substrate degrading bacteria resulted in excellent performance in terms of substrate removal and electricity generation but the effects on hydrocarbon contaminant degradation were not examined. Here we investigate the differences between enriched biofilm anodes and freshly inoculated new anodes in diesel fed single chamber mediatorless microbial fuel cells (DMFC) using various techniques for the enhancement of PH contaminant remediation with concomitant electricity generation. An anodophilic microbial consortium previously selected for over a year through continuous culturing with a diesel concentration of about 800 mg l{sup −1} and which now showed complete removal of this concentration of diesel within 30 days was compared to that of a freshly inoculated new anode MFC (showing 83.4% removal of diesel) with a simultaneous power generation of 90.81 mW/m{sup 2} and 15.04 mW/m{sup 2} respectively. The behaviour of pre-cultured anodes at a higher concentration of PH (8000 mg l{sup −1}) was also investigated. Scanning electron microscopy observation revealed a thick biofilm covering the pre-cultured anodic electrode but not the anode from the freshly inoculated MFC. High resolution imaging showed the presence of thin 60 nm diametre pilus-like projections emanating from the cells. Anodic microbial community profiling confirmed that the selection for diesel degrading exoelectrogenic bacteria had occurred. Identification of a biodegradative gene (alkB) provided strong evidence of the catabolic pathway used for diesel degradation in the DMFCs.

Removal of Cadmium, Zinc, Lead and Copper by Sorption on Leaching Residue from Nickel Production

Directory of Open Access Journals (Sweden)

Miroslava Václavíková

2006-12-01

Full Text Available A leaching resudue from the nickel production (LRNi, was used to study the removal of selected bivalent cations (Cd, Pb, Cu and Zn from model aqueous solutions. Batch-type experiments have been performed in solutions with initial concentrations of heavy metals in the range of 20-400 mg.L-1 and the adsorbent dosage 2 g.L-1. All adsorption experiments were carried out at ambient temperature (22+1°C in orbital shaker. The experimental data were modeled with Langmuir and Freundlich isotherms. The relatively high uptake indicated that LRNi can adsorb considerable amounts of cadmium and zinc (maximum uptake capacity for cadmium: 25 mg/g at pH 7.2 and ca. 40 mg/g for zinc at pH 7. A significant uptake was also observed for copper and lead at pH 5.8 and 6 respectively, which was attributed to the precipitation of the respective insoluble hydroxides.

Arsenic Removal from Drinking Water by Adsorptive Media, U.S. EPA Demonstration Project at LEADS Head Start Building in Buckeye Lake, OH - Final Performance Evaluation Report

Science.gov (United States)

This report documents the activities performed and the results obtained for the arsenic removal treatment technology demonstration project at Licking Economic Action Development Study (LEADS) Head Start School in Buckeye Lake, Ohio. The objectives of the project were to evaluate...

Scalable and reusable micro-bubble removal method to flatten large-area 2D materials

Science.gov (United States)

Pham, Phi H. Q.; Quach, Nhi V.; Li, Jinfeng; Burke, Peter J.

2018-04-01

Bubbles generated during electro-delamination and chemical etch during large-area two-dimensional (2D) material transfer has been shown to cause rippling, and consequently, results in tears and wrinkles in the transferred film. Here, we demonstrate a scalable and reusable method to remove surface adhered micro-bubbles by using hydrophobic surfaces modified by self-assembled monolayers (SAMs). Bubble removal allows the 2D film to flatten out and prevents the formation of defects. Electrical characterization was used to verify improved transfer quality and was confirmed by increased field-effect mobility and decreased sheet resistance. Raman spectroscopy was also used to validate enhanced electrical quality following transfer. The bubble removal method can be applied to an assortment of 2D materials using diverse hydrophobic SAM variants. Our studies can be integrated into large scale applications and will lead to improved large-area 2D electronics in general.

Chelate-assisted phytoextraction of lead from contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Cooper, E.M.; Sims, J.T.; Cunningham, S.D.; Huang, J.W.; Berti, W.R.

1999-12-01

Phytoextraction, a remediation strategy for lead (Pb)-contaminated soils that removes soil Pb through plant uptake and harvest, may be enhanced by use of synthetic chelates. The authors evaluated Pb desorption from four contaminated soils by seven chelates (CDTA, DTPA, EDDHA, EFTA, HEDTA, HEIDA, and NTA) at three rates. The three most effective chelates (CDTA, DTPA, and HEDTA) were used in greenhouse studies with an uncontaminated soil and a Pb-contaminated soil to determine the effect of chelate type and rate on growth, Pb uptake, and plant elemental composition. Lead desorption varied with chelate and soil and increased with chelate rate, averaging 948 mg Pb kg{sup {minus}1} at the 20 mmol kg{sup {minus}1} rate vs. 28 mg Pb kg{sup {minus}1} by the control. The general ranking of chelate effectiveness, based on total Pb desorbed, was HEDTA > CDTA > DTPA > EGTA > HEIDA > EDDHA {approximately} NTA. Plant uptake of Pb from the contaminated soil was enhanced by CDTA, DTPA, and HEDTA, but with even the most effective treatment (corn, high CDTA rate), the amount of Pb extracted by plants was rather low. Lead extractable by the Toxicity Characteristic Leaching Procedure (TCLP) was increased from 9 mg L{sup {minus}1} in the control to from 47 to 174 mg L{sup {minus}1} in soils treated with 20 mmol kg{sup {minus}1} CDTA or DTPA and chelates generally caused a shift in Pb from resistant to more soluble chemical fractions.

Childhood Blood Lead Reductions Following Removal of Leaded Ceramic Glazes in Artisanal Pottery Production: A Success Story

OpenAIRE

Donald E. Jones, MS; Mario Covarrubias Pérez; Bret Ericson; Daniel Estrada Sánchez; Sandra Gualtero; Andrea Smith-Jones, MS; Jack Caravanos, DrPH, CIH

2013-01-01

Background. Lead exposure within artisanal ceramics workshop communities in Mexico continues to be a major source of childhood lead poisoning. Artisanal ceramics workshops expose children through direct ingestion, contaminated soil, and food prepared in lead-glazed pottery. Conversion to non-lead glazes alone may not effectively reduce exposure. This paper describes a model comprehensive intervention and environmental remediation of an artisanal ceramics workshop in the state of Hidalgo, Mexi...

Strategies to enhance the removal of Fluoroquinolones

OpenAIRE

Amorim, Catarina L.; Maia, Alexandra S.; Moreira, Irina S.; van Loosdrecht, Mark C.M.; Tiritan, Maria E.; Castro, Paula M.L.

2013-01-01

Fluoroquinolones (FQs) are broad-spectrum antibiotics that play an important role in the treatment of serious bacterial infections. Currently, several FQs are available but ciprofloxacin (CPF), ofloxacin (OFL) and norfloxacin (NOR) are amongst the most worldwide prescribed antibiotics. Antibiotics can reach wastewater treatment plants (WWTP) from different routes. Thus removal of these contaminants during the biotreatment process is of major importance in order to avoid their release to other...

Evaluation of natural clay Brasgel as adsorbent in removal of lead in synthetic waste water; Avaliacao da argila Brasgel natural como adsorvente na remocao de chumbo de efluentes sinteticos

Energy Technology Data Exchange (ETDEWEB)

Lima, W.S.; Rodrigues, M.G.F.; Mota, M.F.; Patricio, A.C.L.; Silva, M.M., E-mail: wsl_20@yahoo.com.br [Universidade Federal de Campina Grande (LABNOV/UFCG), PB (Brazil). Unidade Academica de Engenharia Quimica. Lab. de Desenvolvimento de Novos Materiais

2012-07-01

The smectite clays have high adsorption capacity and cation exchange. Due to its chemical and physical characteristics, they can be effectively used as adsorbent of pollutants (such as metal ions). The initial objective of this study was to characterize the clay Brasgel through the techniques of X-Ray Diffraction (XRD), X-Ray Spectrometry by Energy Dispersive (EDX) and nitrogen adsorption (BET method), seeking its use in removing lead (Pb{sup 2+}) from synthetic effluents. System was used in finite bath to assess the potential removal of lead (Pb{sup 2+}), following a 2{sup 2} factorial experimental design with three center point experiments, taking as input variables: pH and initial concentrations of lead (Pb{sup 2+}). The clay has Brasgel clay in its composition that characterize it as a smectite clay. By having a large surface area, this clay showed great potential on the adsorption of metal ions. (author)

The Enhancement of H2O2/UV AOPs for the Removal of Selected Organic Pollutants from Drinking Water with Hydrodynamic Cavitation.

Science.gov (United States)

Čehovin, Matej; Medic, Alojz; Kompare, Boris; Žgajnar Gotvajn, Andreja

2016-12-01

Drinking water contains organic matter that occasionally needs to be treated to assure its sufficient quality and safety for the consumers. H2O2 and UV advanced oxidation processes (H2O2/UV AOPs) were combined with hydrodynamic cavitation (HC) to assess the effects on the removal of selected organic pollutants. Water samples containing humic acid, methylene blue dye and micropollutants (metaldehyde, diatrizoic acid, iohexol) were treated first by H2O2 (dosages from 1 to 12 mg L-1) and UV (dosages from 300 to 2800 mJ cm-2) AOPs alone and later in combination with HC, generated by nozzles and orifice plates (4, 8, 18 orifices). Using HC, the removal of humic acid was enhanced by 5-15%, methylene blue by 5-20% and metaldehyde by approx. 10%. Under favouring conditions, i.e. high UV absorbance of the matrix (more than 0.050 cm-1 at a wavelength of 254 nm) and a high pollutant to oxidants ratio, HC was found to improve the hydrodynamic conditions in the photolytic reactor, to improve the subjection of the H2O2 to the UV fluence rate distribution and to enhance the removal of the tested organic pollutants, thus showing promising potential of further research in this field.

A novel redox-based switch: LMW-PTP oxidation enhances Grb2 binding and leads to ERK activation

International Nuclear Information System (INIS)

Giannoni, Elisa; Raugei, Giovanni; Chiarugi, Paola; Ramponi, Giampietro

2006-01-01

Low molecular weight-PTP has been reported as a redox-sensitive protein during both platelet-derived growth factor and integrin signalling. In response to oxidation the phosphatase undergoes a reversible inactivation, which in turn leads to the increase in tyrosine phosphorylation of its substrates and the properly executed anchorage-dependent proliferation program. Here, we report that an exogenous oxidative stress enhances LMW-PTP tyrosine phosphorylation, through oxidation/inactivation of the enzyme, thus preventing its auto-dephosphorylation activity. In particular, we observed a selective hyper-phosphorylation of Tyr132, that acts as a docking site for the adaptor protein Grb2. The redox-dependent enhancement of Grb2 recruitment to LMW-PTP ultimately leads to an improvement of ERK activation, likely triggering a prosurvival signal against the oxidant environment

Population dynamics of bacteria involved in enhanced biological phosphorus removal in Danish wastewater treatment plants.

Science.gov (United States)

Mielczarek, Artur Tomasz; Nguyen, Hien Thi Thu; Nielsen, Jeppe Lund; Nielsen, Per Halkjær

2013-03-15

The enhanced biological phosphorus removal (EBPR) process is increasingly popular as a sustainable method for removal of phosphorus (P) from wastewater. This study consisted of a comprehensive three-year investigation of the identity and population dynamics of polyphosphate-accumulating organisms (PAOs) and glycogen-accumulating organisms (GAOs) in 28 Danish municipal wastewater treatment plants with nutrient removal. Fluorescence in situ hybridization was applied to quantify ten probe-defined populations of PAO and GAO that in total constituted a large fraction (30% on average) of the entire microbial community targeted by the EUBmix probes. Two PAO genera, Accumulibacter and Tetrasphaera, were very abundant in all EBPR plants (average of 3.7% and 27% of all bacteria, respectively), and their abundance was relatively stable in the Danish full-scale plants without clear temporal variations. GAOs were occasionally present in some plants (Competibacter in 11 plants, Defluviicoccus in 6 plants) and were consistent in only a few plants. This shows that these were not core species in the EBPR communities. The total GAO abundance was always lower than that of Accumulibacter. In plants without EBPR design, the abundance of PAO and GAO was significantly lower. Competibacter correlated in general with high fraction of industrial wastewater. In specific plants Accumulibacter correlated with high C/P ratio of the wastewater and Tetrasphaera with high organic loading. Interestingly, the relative microbial composition of the PAO/GAO species was unique to each plant over time, which gives a characteristic plant-specific "fingerprint". Copyright © 2012 Elsevier Ltd. All rights reserved.

Lead recovery and high silica glass powder synthesis from waste CRT funnel glasses through carbon thermal reduction enhanced glass phase separation process

Energy Technology Data Exchange (ETDEWEB)

Xing, Mingfei [Henan Key Laboratory Cultivation Base of Mine Environmental Protection and Ecological Remediation, Henan Polytechnic University, Jiaozuo 454000 Henan China (China); Institute of Resource and Environment, Henan Polytechnic University, Jiaozuo 454000 Henan China (China); Fu, Zegang [Institute of Resource and Environment, Henan Polytechnic University, Jiaozuo 454000 Henan China (China); Wang, Yaping, E-mail: wangyp326@163.com [School of Surveying and Land Information Engineering, Henan Polytechnic University, Jiaozuo 454000, Henan China (China); Wang, Jingyu [Institute of Resource and Environment, Henan Polytechnic University, Jiaozuo 454000 Henan China (China); Zhang, Zhiyuan [Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

2017-01-15

Highlights: • CRT funnel glass was remelted with B{sub 2}O{sub 3} in reducing atmosphere. • A part of PbO was reduced into Pb and detached from the glass phase. • The rest of PbO and other metal oxides were mainly concentrated in the B{sub 2}O{sub 3} phase. • PbO enriched in the interconnected B{sub 2}O{sub 3} phase can be completely leached out by HNO{sub 3}. • High silica glass powder(SiO{sub 2} purity >95%) was obtained after the leaching process. - Abstract: In this study, a novel process for the removal of toxic lead from the CRT funnel glass and synchronous preparation of high silica glass powder was developed by a carbon-thermal reduction enhanced glass phase separation process. CRT funnel glass was remelted with B{sub 2}O{sub 3} in reducing atmosphere. In the thermal process, a part of PbO contained in the funnel glass was reduced into metallic Pb and detached from the glass phase. The rest of PbO and other metal oxides (including Na{sub 2}O, K{sub 2}O, Al{sub 2}O{sub 3,} BaO and CaO) were mainly concentrated in the boric oxide phase. The metallic Pb phase and boric oxide phase were completely leached out by 5 mol/L HNO{sub 3}. The lead removal rate was 99.80% and high silica glass powder (SiO{sub 2} purity >95 wt%) was obtained by setting the temperature, B{sub 2}O{sub 3} added amount and holding time at 1000 °C, 20% and 30 mins, respectively. The prepared high silicate glass powders can be used as catalyst carrier, semipermeable membranes, adsorbents or be remelted into high silicate glass as an ideal substitute for quartz glass. Thus this study proposed an eco-friendly and economical process for recycling Pb-rich electronic glass waste.

Implementation and Effectiveness of Early Chest Tube Removal during an Enhanced Recovery Programme after Oesophago-gastrectomy

Directory of Open Access Journals (Sweden)

Rajeev Bhandari

2015-03-01

Full Text Available Introduction: Oesophageal resection were notoriously complicated and produces a cohort of patients prone to postoperative complications and here we would like to focus on the implementation and effectiveness of early chest tube removal in ERAS after oesophago-gastrectomy considering the various aspect like pleural effusion and reducing the length of hospital stay which ultimately lead to reducing the economic burden on patient. Methods: An ERAS programme was devised and implemented with the support of a dedicated in-hospital task-force. The patients underwent esophago-gastrectomy were randomly divided into two groups: the ERAS group and the control group (non-ERAS. The ERAS group was treated with early removal of the chest tube after surgery, and the control group was treated with traditional way and outcomes were compared between them. Results: The length of hospital stay and the cost of hospitalization in the ERAS group were significantly lower than those in the control group（p<0.05. However, there was no statistical significant difference in the incidences of pleural effusion between the two groups（p＞0.05. Conclusions: The introduction of early chest tube removal as an ERAS programme after oesophago-gastrectomy would not increase the risk of pleural effusion and would not increase the total length of stay and cost of hospitalisation without jeopardising patient safety or clinical outcomes.

Cardiac implantable electronic device lead extraction using the lead-locking device system: keeping it simple, safe, and inexpensive with mechanical tools and local anesthesia.

Science.gov (United States)

Manolis, Antonis S; Georgiopoulos, Georgios; Metaxa, Sofia; Koulouris, Spyridon; Tsiachris, Dimitris

2017-10-01

We have previously reported our successful approach for percutaneous cardiac implantable electronic device (CIED) lead extraction using inexpensive tools, which we have continued over the years. Herein we report the results of the systematic use of a unique stylet, the lead-locking device (LLD), which securely locks the entire lead lumen, aided with non-powered telescoping sheaths in 54 patients to extract 98 CIED leads. This prospective observational clinical study included 38 men and 16 women aged 68.9±13.1 years undergoing lead extraction for device infection (n=46), lead malfunction (n=5), or prior to defibrillator implant (n=3). Leads were in place for 6.7±4.3 years. Infections were more commonly due to Staphylococcus species (n=40). There were 78 pacing (31 ventricular, 37 atrial, 4 VDD, and 6 coronary sinus leads) and 20 defibrillating leads. Using simple traction (6 leads) and the LLD stylets (92 leads) aided with telescoping sheaths (15 patients), 96 (98%) leads in 52 (96.3%) patients were successfully removed, with all but one leads removed using a subclavian approach; in 1 patient, the right femoral approach was also required. In 2 patients, distal fragments from one ventricular pacing and one defibrillating lead could not be removed. Finally, lead removal was completely (52/54) (96.3%) or partially (2/54) (3.7%) successful in 54 patients for 96 of 98 leads (98%) without major complications. Percutaneous lead extraction can be successful with mechanical tools using the LLD locking stylet aided with non-powered telescoping sheaths through a simplified, safe, and inexpensive procedure using local anesthesia.

Nitrogen removal from coal gasification wastewater by activated carbon technologies combined with short-cut nitrogen removal process.

Science.gov (United States)

Zhao, Qian; Han, Hongjun; Hou, Baolin; Zhuang, Haifeng; Jia, Shengyong; Fang, Fang

2014-11-01

A system combining granular activated carbon and powdered activated carbon technologies along with shortcut biological nitrogen removal (GAC-PACT-SBNR) was developed to enhance total nitrogen (TN) removal for anaerobically treated coal gasification wastewater with less need for external carbon resources. The TN removal efficiency in SBNR was significantly improved by introducing the effluent from the GAC process into SBNR during the anoxic stage, with removal percentage increasing from 43.8%-49.6% to 68.8%-75.8%. However, the TN removal rate decreased with the progressive deterioration of GAC adsorption. After adding activated sludge to the GAC compartment, the granular carbon had a longer service-life and the demand for external carbon resources became lower. Eventually, the TN removal rate in SBNR was almost constant at approx. 43.3%, as compared to approx. 20.0% before seeding with sludge. In addition, the production of some alkalinity during the denitrification resulted in a net savings in alkalinity requirements for the nitrification reaction and refractory chemical oxygen demand (COD) degradation by autotrophic bacteria in SBNR under oxic conditions. PACT showed excellent resilience to increasing organic loadings. The microbial community analysis revealed that the PACT had a greater variety of bacterial taxons and the dominant species associated with the three compartments were in good agreement with the removal of typical pollutants. The study demonstrated that pre-adsorption by the GAC-sludge process could be a technically and economically feasible method to enhance TN removal in coal gasification wastewater (CGW). Copyright © 2014. Published by Elsevier B.V.

Lead elimination by ICRF 158 in rats after chronic lead exposure

Energy Technology Data Exchange (ETDEWEB)

Witting, U; Hultsch, E

1981-02-01

Lead elimination by ICRF 158, a lipophilic derivative of ethylene-diaminetetra-acetate (EDTA), was investigated in rats after chronic lead exposure. The animals had received a lead concentration of 550 ppm in their drinking water for 140 days. Subsequent treatment with ICRF 158 for 30 days led to increased mobilization and elimination of incorporated lead, and the lead-induced inhibition of hemosynthesis was removed. ICR 158 produced no renal damage in excess to lead-induced tubular nephrosis. Separate toxicity tests in mice demonstrated that is less toxic than CaNa/sub 2/EDTA. ICRF 158 does not form stable complexes with lead ions in vitro. The mechanism of action of this lipophilic EDTA derivative is compared to that of its hydrophilic correspondent, the chelating agent CaNa/sub 2/EDTA.

Facile biofunctionalization of silver nanoparticles for enhanced antibacterial properties, endotoxin removal, and biofilm control

Directory of Open Access Journals (Sweden)

Lambadi PR

2015-03-01

Full Text Available Paramesh Ramulu Lambadi,1,* Tarun Kumar Sharma,1,* Piyush Kumar,1 Priyanka Vasnani,2 Sitaramanjaneya Mouli Thalluri,2 Neha Bisht,1 Ranjana Pathania,1,2 Naveen Kumar Navani1,21Department of Biotechnology, 2Centre of Nanotechnology, Indian Institute of Technology, Roorkee, Uttarakhand, India*These authors contributed equally to this workAbstract: Infectious diseases cause a huge burden on healthcare systems worldwide. Pathogenic bacteria establish infection by developing antibiotic resistance and modulating the host’s immune system, whereas opportunistic pathogens like Pseudomonas aeruginosa adapt to adverse conditions owing to their ability to form biofilms. In the present study, silver nanoparticles were biofunctionalized with polymyxin B, an antibacterial peptide using a facile method. The biofunctionalized nanoparticles (polymyxin B-capped silver nanoparticles, PBSNPs were assessed for antibacterial activity against multiple drug-resistant clinical strain Vibrio fluvialis and nosocomial pathogen P. aeruginosa. The results of antibacterial assay revealed that PBSNPs had an approximately 3-fold higher effect than the citrate-capped nanoparticles (CSNPs. Morphological damage to the cell membrane was followed by scanning electron microscopy, testifying PBSNPs to be more potent in controlling the bacterial growth as compared with CSNPs. The bactericidal effect of PBSNPs was further confirmed by Live/Dead staining assays. Apart from the antibacterial activity, the biofunctionalized nanoparticles were found to resist biofilm formation. Electroplating of PBSNPs onto stainless steel surgical blades retained the antibacterial activity against P. aeruginosa. Further, the affinity of polymyxin for endotoxin was exploited for its removal using PBSNPs. It was found that the prepared nanoparticles removed 97% of the endotoxin from the solution. Such multifarious uses of metal nanoparticles are an attractive means of enhancing the potency of antimicrobial

Hydrogen Peroxide Enhances Removal of NOx from Flue Gases

Science.gov (United States)

Collins, Michelle M.

2005-01-01

Pilot scale experiments have demonstrated a method of reducing the amounts of oxides of nitrogen (NOx) emitted by industrial boilers and powerplant combustors that involves (1) injection of H2O2 into flue gases and (2) treatment of the flue gases by caustic wet scrubbing like that commonly used to remove SO2 from combustion flue gases. Heretofore, the method most commonly used for removing NOx from flue gases has been selective catalytic reduction (SCR), in which the costs of both installation and operation are very high. After further development, the present method may prove to be an economically attractive alternative to SCR.

The location and nature of accumulated phosphorus in seven sludges from activated sludge plants which exhibited enhanced phosphorus removal

International Nuclear Information System (INIS)

Buchan, L.

1981-01-01

Electron microscopy combined with the energy dispersive analysis of X-rays (EDX) has been used to examine the nature of the phosphorus accumulated in sludges from seven activated sludge plants exhibiting enhanced phosphorus removal. Large phosphorus accumulations were located in identical structures in the sludges examined. The phosphorus was located in large electron-dense bodies, within large bacterial cells which were characteristically grouped in clusters. The calcium:phosphorus ratio of these electron-dense bodies precluded them from being any form of calcium phosphate precipitate. Quantitative analysis indicated that the electron-dense bodies contained in excess of 30% phosphorus. The results obtained are supportive of a biological mechanism of enhanced phosphorus uptake in activated sludge

Enhancing the nonlinear thermoelectric response of a correlated quantum dot in the Kondo regime by asymmetrical coupling to the leads

Science.gov (United States)

Pérez Daroca, Diego; Roura-Bas, Pablo; Aligia, Armando A.

2018-04-01

We study the low-temperature properties of the differential response of the current to a temperature gradient at finite voltage in a single-level quantum dot including electron-electron interaction, nonsymmetric couplings to the leads, and nonlinear effects. The calculated response is significantly enhanced in setups with large asymmetries between the tunnel couplings. In the investigated range of voltages and temperatures with corresponding energies up to several times the Kondo energy scale, the maximum response is enhanced nearly an order of magnitude with respect to symmetric coupling to the leads.

Enhanced photocatalytic activity and characterization of magnetic Ag/BiOI/ZnFe2O4 composites for Hg0 removal under fluorescent light irradiation

Science.gov (United States)

Li, Chengwei; Zhang, Anchao; Zhang, Lixiang; Song, Jun; Su, Sheng; Sun, Zhijun; Xiang, Jun

2018-03-01

A series of magnetic Ag/BiOI/ZnFe2O4 hybrids synthesized via hydrothermal process, subsequent deposition-precipitation and photoreduction method were employed to remove elemental mercury (Hg0) under fluorescent light irradiation. The effects of Ag content, fluorescent light irradiation, reaction temperature, pH value, flue gas composition, anions and photocatalyst dosage on Hg0 removal were investigated in detail. The as-synthesized photocatalysts were characterized using N2 adsorption-desorption, XRD, SEM, TEM, HRTEM, XPS, VSM, DRS, ESR, PL and photocurrent response. The results showed that the ternary Ag/BiOI/ZnFe2O4 hybrids possessed enhanced visible-light-responsive photocatalytic performances for Hg0 removal. Ag/BiOI/ZnFe2O4 photocatalyst could be easily recovered from the reaction solution by an extra magnet and was stable in the process of Hg0 removal. Lower content of Ag was highly dispersed on the surface of BiOI/ZnFe2O4, while higher content of Ag would result in some aggregations and/or the blockages of micropore. In comparison to BiOI/ZnFe2O4, Ag deposited BiOI/ZnFe2O4 material showed lower recombination rate of electron-hole pairs. The superior Hg0 oxidation removal could correspond to good match of BiOI and ZnFe2O4, excellent fluidity and surface plasmon resonance effect of Ag0 nanoparticles, which led to higher separation efficiency of photogenerated electrons and holes, thereby enhancing the hybrids' photocatalytic activity.

Do new wipe materials outperform traditional lead dust cleaning methods?

Science.gov (United States)

Lewis, Roger D; Ong, Kee Hean; Emo, Brett; Kennedy, Jason; Brown, Christopher A; Condoor, Sridhar; Thummalakunta, Laxmi

2012-01-01

Government guidelines have traditionally recommended the use of wet mopping, sponging, or vacuuming for removal of lead-contaminated dust from hard surfaces in homes. The emergence of new technologies, such as the electrostatic dry cloth and wet disposable clothes used on mopheads, for removal of dust provides an opportunity to evaluate their ability to remove lead compared with more established methods. The purpose of this study was to determine if relative differences exist between two new and two older methods for removal of lead-contaminated dust (LCD) from three wood surfaces that were characterized by different roughness or texture. Standard leaded dust, coefficient of friction was performed for each wipe material. Analysis of variance was used to evaluate the surface and cleaning methods. There were significant interactions between cleaning method and surface types, p = 0.007. Cleaning method was found be a significant factor in removal of lead, p coefficient of friction, significantly different among the three wipes, is likely to influence the cleaning action. Cleaning method appears to be more important than texture in LCD removal from hard surfaces. There are some small but important factors in cleaning LCD from hard surfaces, including the limits of a Swiffer mop to conform to curved surfaces and the efficiency of the wetted shop towel and vacuuming for cleaning all surface textures. The mean percentage reduction in lead dust achieved by the traditional methods (vacuuming and wet wiping) was greater and more consistent compared to the new methods (electrostatic dry cloth and wet Swiffer mop). Vacuuming and wet wiping achieved lead reductions of 92% ± 4% and 91%, ± 4%, respectively, while the electrostatic dry cloth and wet Swiffer mops achieved lead reductions of only 89 ± 8% and  81 ± 17%, respectively.

Dam removal: Listening in

Science.gov (United States)

Foley, M. M.; Bellmore, J. R.; O'Connor, J. E.; Duda, J. J.; East, A. E.; Grant, G. E.; Anderson, C. W.; Bountry, J. A.; Collins, M. J.; Connolly, P. J.; Craig, L. S.; Evans, J. E.; Greene, S. L.; Magilligan, F. J.; Magirl, C. S.; Major, J. J.; Pess, G. R.; Randle, T. J.; Shafroth, P. B.; Torgersen, C. E.; Tullos, D.; Wilcox, A. C.

2017-07-01

Dam removal is widely used as an approach for river restoration in the United States. The increase in dam removals—particularly large dams—and associated dam-removal studies over the last few decades motivated a working group at the USGS John Wesley Powell Center for Analysis and Synthesis to review and synthesize available studies of dam removals and their findings. Based on dam removals thus far, some general conclusions have emerged: (1) physical responses are typically fast, with the rate of sediment erosion largely dependent on sediment characteristics and dam-removal strategy; (2) ecological responses to dam removal differ among the affected upstream, downstream, and reservoir reaches; (3) dam removal tends to quickly reestablish connectivity, restoring the movement of material and organisms between upstream and downstream river reaches; (4) geographic context, river history, and land use significantly influence river restoration trajectories and recovery potential because they control broader physical and ecological processes and conditions; and (5) quantitative modeling capability is improving, particularly for physical and broad-scale ecological effects, and gives managers information needed to understand and predict long-term effects of dam removal on riverine ecosystems. Although these studies collectively enhance our understanding of how riverine ecosystems respond to dam removal, knowledge gaps remain because most studies have been short (< 5 years) and do not adequately represent the diversity of dam types, watershed conditions, and dam-removal methods in the U.S.

Corrosion by liquid lead and lead-bismuth: experimental results review and analysis

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jinsuo [Los Alamos National Laboratory

2008-01-01

Liquid metal technologies for liquid lead and lead-bismuth alloy are under wide investigation and development for advanced nuclear energy systems and waste transmutation systems. Material corrosion is one of the main issues studied a lot recently in the development of the liquid metal technology. This study reviews corrosion by liquid lead and lead bismuth, including the corrosion mechanisms, corrosion inhibitor and the formation of the protective oxide layer. The available experimental data are analyzed by using a corrosion model in which the oxidation and scale removal are coupled. Based on the model, long-term behaviors of steels in liquid lead and lead-bismuth are predictable. This report provides information for the selection of structural materials for typical nuclear reactor coolant systems when selecting liquid lead or lead bismuth as heat transfer media.

Thermodynamic, Kinetic, and Equilibrium Parameters for the Removal of Lead and Cadmium from Aqueous Solutions with Calcium Alginate Beads

Directory of Open Access Journals (Sweden)

Ruth Alfaro-Cuevas-Villanueva

2014-01-01

Full Text Available The sorption of cadmium (Cd and lead (Pb by calcium alginate beads (CAB from aqueous solutions in batch systems was investigated. The kinetic and thermodynamic parameters, as well as the sorption capacities of CAB in each system at different temperatures, were evaluated. The rate of sorption for both metals was rapid in the first 10 minutes and reached a maximum in 50 minutes. Sorption kinetic data were fitted to Lagergren, pseudo-second-order and Elovich models and it was found that the second-order kinetic model describes these data for the two metals; comparing kinetic parameters for Cd and Pb sorption a higher kinetic rate (K2 for Pb was observed, indicating that the interaction between lead cations and alginate beads was faster than for cadmium. Similarly, isotherm data were fitted to different models reported in literature and it was found that the Langmuir-Freundlich (L-F and Dubinin-Radushkevich (D-R models describe the isotherms in all cases. CAB sorption capacity for cadmium was 27.4 mg/g and 150.4 mg/g for lead, at 25°C. Sorption capacities of Cd and Pb increase as temperature rises. According to the thermodynamic parameters, the cadmium and lead adsorption process was spontaneous and endothermic. It was also found that pH has an important effect on the adsorption of these metals by CAB, as more were removed at pH values between 6 and 7.

A reactive barrier to enhance the removal of emerging organic compounds during artificial recharge of aquifers through infiltration basins

OpenAIRE

Valhondo, Cristina

2017-01-01

Artificial recharge of aquifers through infiltration basins (AR) improves water quality and in- creases groundwater resources, which make of it an appropriate technique for the renaturalization of waters affected directly or indirectly by wastewater effluents. Emerging organic compounds (EOCs), typically present in such waters, are mainly reduced during AR by sorption and biotrans- formation. We installed a reactive barrier in an infiltration basin (5000 m2) to enhance the removal of EOCs ...

Recovery and enhancement plan development for the Leading Creek watershed, Meigs County, Ohio

International Nuclear Information System (INIS)

Currie, R.J.; Cherry, D.S.; Latimer, H.A.; Babendreier, J.E.; Van Hassel, J.H.

1998-01-01

Following the flooding of the Meigs No. 31 coal mine in Meigs County, Ohio, a proactive plan was developed to evaluate initial dewatering effects, recovery and development of a watershed enhancement plan. Approximately half of the 31-mile Leading Creek mainstem received ∼one billion gallons of coal mine discharge, including sludge and slurry. Damage to the stream system resulted from high conductivity (∼6,000 micromhos/cm), low pH (2.5--3.5), high metals (aluminum, cadmium, copper, iron and iron floc, lead, manganese, nickel and zinc) and total suspended solids. Most forms of aquatic life were depleted in the impacted areas. Four years after the incident, many forms of benthic macroinvertebrates and fish have recovered in the creek, with sediments purged of metals by stormwater events. The enhancement plan involves a reconnaissance of the creek and tributaries pinpointing areas of agricultural sedimentation and abandoned minedland discharges (AMD). Seventeen tributary and ten mainstem stations were addressed as point source discharges with water/sediment toxicity and in-situ testing of Asian clams. One-third of the stations were intermittently toxic from rainfall runoff and the degree of AMD input. Benthic macroinvertebrates in many tributaries were stressed and comprised 1--5 taxa. Erosion/sedimentation was addressed by the USEPA 1-Dimensional Hydrologic Simulation Program Fortran (HSPF) model, as well as incorporating land use management/habitat assessment, and data management by Geographical Information Systems

Enhanced performance of starter lighting ignition type lead-acid batteries with carbon nanotubes as an additive to the active mass

Science.gov (United States)

Marom, Rotem; Ziv, Baruch; Banerjee, Anjan; Cahana, Beni; Luski, Shalom; Aurbach, Doron

2015-11-01

Addition of various carbon materials into lead-acid battery electrodes was studied and examined in order to enhance the power density, improve cycle life and stability of both negative and positive electrodes in lead acid batteries. High electrical-conductivity, high-aspect ratio, good mechanical properties and chemical stability of multi-wall carbon nanotubes (MWCNT, unmodified and mofified with carboxylic groups) position them as viable additives to enhance the electrodes' electrical conductivity, to mitigate the well-known sulfation failure mechanism and improve the physical integration of the electrodes. In this study, we investigated the incorporation-effect of carbon nanotubes (CNT) to the positive and the negative active materials in lead-acid battery prototypes in a configuration of flooded cells, as well as gelled cells. The cells were tested at 25% and 30% depth-of-discharge (DOD). The positive effect of the carbon nanotubes (CNT) utilization as additives to both positive and negative electrodes of lead-acid batteries was clearly demonstrated and is explained herein based on microscopic studies.

Oil removal of spent hydrotreating catalyst CoMo/Al{sub 2}O{sub 3} via a facile method with enhanced metal recovery

Energy Technology Data Exchange (ETDEWEB)

Yang, Yue [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Xu, Shengming, E-mail: smxu@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Beijing Key Lab of Radioactive Wastes Treatment, Tsinghua University, Beijing 100084 (China); Li, Zhen [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Wang, Jianlong [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Beijing Key Lab of Radioactive Wastes Treatment, Tsinghua University, Beijing 100084 (China); Zhao, Zhongwei [School of Metallurgy and Environment, Central South University, Changsha 410083, Hunan (China); Xu, Zhenghe, E-mail: zhenghe.xu@ualberta.ca [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Department of Chemical and Material Engineering, University of Alberta, Edmonton, Alberta T6G 1H9 (Canada)

2016-11-15

Highlights: • A novel approach for oil removal from spent hydrotreating catalysts has been developed. • Oil removal possibility is analyzed through surface characteristics. • Oil is successfully removed from spent catalysts via aqueous surfactant solution. • Over 98% Mo can be leached after oil removal and thermal treatment. • The proposed deoiling method helps to avoid detrimental impurity generation (CoMoO{sub 4}) and enhance metal recovery. - Abstract: Deoiling process is a key issue for recovering metal values from spent hydrotreating catalysts. The oils can be removed with organic solvents, but the industrialized application of this method is greatly hampered by the high cost and complex processes. Despite the roasting method is simple and low-cost, it generates hardest-to-recycle impurities (CoMoO{sub 4} or NiMoO{sub 4}) and enormous toxic gases. In this study, a novel and facile approach to remove oils from the spent hydrotreating catalysts is developed. Firstly, surface properties of spent catalysts are characterized to reveal the possibility of oil removal. And then, oils are removed with water solution under the conditions of 90 °C, 0.1 wt% SDS, 2.0 wt% NaOH and 10 ml/g L/S ratio for 4 h. Finally, thermal treatment and leaching tests are carried out to further explore the advantages of oil removal. The results show that no hardest-to-recycle impurity CoMoO{sub 4} is found in XPS spectra of thermally treated samples after deoiling and molybdenum is leached completely with sodium carbonate solution. It means that the proposed deoiling method can not only remove oils simply and without enormous harmful gases generating, but also avoid the generation of detrimental impurity and promote recycling of valuable metals from spent hydrotreating catalysts.

Removal of phenol from synthetic waste water using Gemini micellar-enhanced ultrafiltration (GMEUF)

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wenxiang [MOE Key Laboratory of Regional Energy and Environmental Systems Optimization, Resources and Environmental Research Academy, North China Electric Power University, Beijing 102206 (China); Huang, Guohe, E-mail: huang@iseis.org [MOE Key Laboratory of Regional Energy and Environmental Systems Optimization, Resources and Environmental Research Academy, North China Electric Power University, Beijing 102206 (China); Wei, Jia [Faculty of Engineering and Applied Science, University of Regina, Regina, Saskatchewan, Canada S4S 0A2 (Canada); Li, Huiqin; Zheng, Rubing; Zhou, Ya [MOE Key Laboratory of Regional Energy and Environmental Systems Optimization, Resources and Environmental Research Academy, North China Electric Power University, Beijing 102206 (China)

2012-10-15

Highlights: Black-Right-Pointing-Pointer Gemini surfactant micellar enhanced ultrafiltration was used to remove phenol. Black-Right-Pointing-Pointer The effect of different hydrophilic head groups of surfactant was analyzed. Black-Right-Pointing-Pointer SEM, ATR-FTIR and mercury porosimeter were applied to elucidate membrane fouling. Black-Right-Pointing-Pointer Gemini surfactant had superior performance in comparing with conventional surfactant. - Abstract: Comprehensive studies were conducted on the phenol wastewater ultrafiltration (UF) with the help of various concentrations of cationic Gemini surfactant (N1-dodecyl-N1,N1,N2,N2-tetramethyl-N2-octylethane-1,2-diaminium bromide, CG), conventional cationic surfactant (dodecyl trimethyl ammonium bromide, DTAB), anionic surfactant (sodium dodecyl sulfate, SDS) and nonionic surfactant ((dodecyloxy)polyethoxyethanol, Brij35). A flat sheet module with polyethersulfone (PES) membrane was employed in this investigation. The effects of feed concentration (phenol and surfactant) on the retention of phenol and surfactant, permeate flux and membrane fouling by micelles were evaluated. The distribution coefficient (D), the loading of the micelles (L{sub m}) and the equilibrium distribution constant (K) were also utilized to estimate the micellar-enhanced ultrafiltration ability for phenol. Scanning electron microscope (SEM), Fourier transform infrared spectrometer with attenuated total reflectance accessory (ATR-FTIR) and mercury porosimeter were applied to analyze membrane surface morphology, membrane material characteristics and membrane fouling for the original and fouled membranes. Based on the above analysis, the performance of the selected Gemini surfactant was proved superior in the following aspects: retention of phenol/surfactant (peak value is 95.8% for phenol retention), permeate flux and membrane fouling with respect to other conventional surfactants possessing equal alkyl chain length. These results demonstrated

Reformulating Lead-Based Paint as a Problem in Canada

Science.gov (United States)

Perron, Amélie

2011-01-01

Leaded gasoline was officially removed from the Canadian market in December 1990. The removal of a major lead source and the subsequent decline in children's blood lead levels marked an important transition point and sparked the emergence of new discourse on lead in Canada. Today, childhood lead poisoning is viewed as a problem of the past or a problem of the United States. Sparse Canadian surveillance data supported this view. Moreover, tensions among federal agencies evolved into a power struggle, with Health Canada ultimately becoming the dominant authority, thereby relegating important research initiatives to obscurity and also shaping a vastly weaker regulatory response to lead than occurred in the United States. PMID:21836119

Medium-Power Lead-Alloy Reactors: Missions for This Reactor Technology

International Nuclear Information System (INIS)

Todreas, Neil E.; MacDonald, Philip E.; Hejzlar, Pavel; Buongiorno, Jacopo; Loewen, Eric P.

2004-01-01

A multiyear project at the Idaho National Engineering and Environmental Laboratory and the Massachusetts Institute of Technology investigated the potential of medium-power lead-alloy-cooled technology to perform two missions: (1) the production of low-cost electricity and (2) the burning of actinides from light water reactor (LWR) spent fuel. The goal of achieving a high power level to enhance economic performance simultaneously with adoption of passive decay heat removal and modularity capabilities resulted in designs in the range of 600-800 MW(thermal), which we classify as a medium power level compared to the lower [∼100 MW(thermal)] and higher [2800 MW(thermal)] power ratings of other lead-alloy-cooled designs. The plant design that was developed shows promise of achieving all the Generation-IV goals for future nuclear energy systems: sustainable energy generation, low overnight capital cost, a very low likelihood and degree of core damage during any conceivable accident, and a proliferation-resistant fuel cycle. The reactor and fuel cycle designs that evolved to achieve these missions and goals resulted from study of the following key trade-offs: waste reduction versus reactor safety, waste reduction versus cost, and cost versus proliferation resistance. Secondary trade-offs that were also considered were monolithic versus modular design, active versus passive safety systems, forced versus natural circulation, alternative power conversion cycles, and lead versus lead-bismuth coolant.These studies led to a selection of a common modular design with forced convection cooling, passive decay heat removal, and a supercritical CO 2 power cycle for all our reactor concepts. However, the concepts adopt different core designs to optimize the achievement of the two missions. For the low-cost electricity production mission, a design approach based on fueling with low enriched uranium operating without costly reprocessing in a once-through cycle was pursued to achieve a

Separation of Rhenium from Lead-Rich Molybdenite Concentrate via Hydrochloric Acid Leaching Followed by Oxidative Roasting

Directory of Open Access Journals (Sweden)

Guanghui Li

2016-11-01

Full Text Available Lead-rich molybdenite is a typical rhenium-bearing molybdenum resource in China, which has not been efficiently utilized due to its high contents of lead and gangue minerals. In this study, hydrochloric acid was used for preliminarily removing lead and calcite from a lead-rich molybdenite concentrate. Oxidative roasting-ammonia leaching was then carried out for separation of rhenium and extraction of molybdenum. The hydrochloric acid leaching experiments revealed that 93.6% Pb and 97.4% Ca were removed when the leaching was performed at 95 °C for 10 min with HCl concentration of 8 wt. % and liquid-solid ratio of 5 (mL/g. The results of direct oxidative roasting indicated that 89.3% rhenium was volatilized from the raw concentrate after roasting at 600 °C for 120 min in air. In contrast, the rhenium volatilization was enhanced distinctly to 98.0% after the acid-leached concentrate (leaching residue was roasted at 550 °C for 100 min. By the subsequent ammonia leaching, 91.5% molybdenum was leached out from the calcine produced from oxidative roasting of the acid-leached concentrate, while only 79.3% Mo was leached from the calcine produced by roasting molybdenite concentrate without pretreatment.

Enhanced removal of Se(VI) from water via pre-corrosion of zero-valent iron using H2O2/HCl: Effect of solution chemistry and mechanism investigation.

Science.gov (United States)

Shan, Chao; Chen, Jiajia; Yang, Zhe; Jia, Huichao; Guan, Xiaohong; Zhang, Weiming; Pan, Bingcai

2018-04-15

Although the removal of Se(VI) from water by using zero-valent iron (ZVI) is a promising method, passivation of ZVI severely inhibits its performance. To overcome such issue, we proposed an efficient technique to enhance Se(VI) removal via pre-corrosion of ZVI with H 2 O 2 /HCl in a short time (15 min). The resultant pcZVI suspension was weakly acidic (pH 4.56) and contained abundant aqueous Fe 2+ . 57 Fe Mössbauer spectroscopy showed that pcZVI mainly consisted of Fe 0 (66.2%), hydrated ferric oxide (26.3%), and Fe 3 O 4 (7.5%). Efficient removal of Se(VI) from sulfate-rich solution was achieved by pcZVI compared with ZVI (in the absence and presence of H 2 O 2 ) and acid-pretreated ZVI. Moreover, the efficient removal of Se(VI) by pcZVI sustained over a broad pH range (3-9) due to its strong buffering power. The presence of chloride, carbonate, nitrate, and common cations (Na + , K + , Ca 2+ , and Mg 2+ ) posed negligible influence on the removal of Se(VI) by pcZVI, while the inhibitory effect induced by sulfate, silicate, and phosphate indicated the significance of Se(VI) adsorption as a prerequisite step for its removal. The consumption of aqueous Fe 2+ was associated with Se(VI) removal, and X-ray absorption near edge structure revealed that the main pathway for Se(VI) removal by pcZVI was a stepwise reduction of Se(VI) to Se(IV) and then Se 0 as the dominant final state (78.2%). Moreover, higher electron selectivity of pcZVI was attributed to the enhanced enrichment of Se oxyanions prior to their reduction. Copyright © 2018 Elsevier Ltd. All rights reserved.

Denitrifying capabilities of Tetrasphaera and their contribution towards nitrous oxide production in enhanced biological phosphorus removal processes.

Science.gov (United States)

Marques, Ricardo; Ribera-Guardia, Anna; Santos, Jorge; Carvalho, Gilda; Reis, Maria A M; Pijuan, Maite; Oehmen, Adrian

2018-06-15

Denitrifying enhanced biological phosphorus removal (EBPR) systems can be an efficient means of removing phosphate (P) and nitrate (NO 3 - ) with low carbon source and oxygen requirements. Tetrasphaera is one of the most abundant polyphosphate accumulating organisms present in EBPR systems, but their capacity to achieve denitrifying EBPR has not previously been determined. An enriched Tetrasphaera culture, comprising over 80% of the bacterial biovolume was obtained in this work. Despite the denitrification capacity of Tetrasphaera, this culture achieved only low levels of anoxic P-uptake. Batch tests with different combinations of NO 3 - , nitrite (NO 2 - ) and nitrous oxide (N 2 O) revealed lower N 2 O accumulation by Tetrasphaera as compared to Accumulibacter and Competibacter when multiple electron acceptors were added. Electron competition was observed during the addition of multiple nitrogen electron acceptors species, where P uptake appeared to be slightly favoured over glycogen production in these situations. This study increases our understanding of the role of Tetrasphaera-related organisms in denitrifying EBPR systems. Copyright © 2018 Elsevier Ltd. All rights reserved.

Decay heat removal analyses in heavy-liquid-metal-cooled fast breeding reactors. Development of the thermal-hydraulic analysis method for lead-bismuth-cooled, natural-circulation reactors

Energy Technology Data Exchange (ETDEWEB)

Sakai, Takaaki; Enuma, Yasuhiro [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center; Iwasaki, Takashi [Nuclear Energy System Inc., Tokyo (Japan); Ohyama, Kazuhiro [Advanced Reactor Technology Co., Ltd., Tokyo (Japan)

2001-05-01

The feasibility study on future commercial fast breeder reactors in Japan has been conducted at JNC, in which various plant design options with all the possible coolant and fuel types are investigated to determine the conditions for the future detailed study. Lead-bismuth eutectic coolant has been selected as one of the possible coolant options. During the phase-I activity of the feasibility study in FY1999 and FY2000, several plant concepts, which were cooled by the heavy liquid metal coolant, were examined to evaluate the feasibility mainly with respect to economical competitiveness with other coolant reactors. A medium-scale (300 - 550 MWe) plant, cooled by a lead-bismuth natural circulation flow in a pool type vessel, was selected as the most possible plant concept for the heavy liquid metal coolant. Thus, a conceptual design study for a lead-bismuth-cooled, natural-circulation reactor of 400 MWe has been performed at JNC to identify remaining difficulties in technological aspect and its construction cost evaluation. In this report, a thermal-hydraulic analysis method for lead-bismuth-cooled, natural-circulation reactors is described. A Multi-dimensional Steam Generator analysis code (MSG) was applied to evaluate the natural circulation plant by combination with a flow-network-type, plant dynamics code (Super-COPD). By using this combined multi-dimensional plant dynamics code, decay heat removals, ULOHS and UTOP accidents were evaluated for the 100 MWe STAR-LM concept designed by ANL. In addition, decay heat removal by the Primary Reactor Auxiliary Cooling System (PRACS) in the 400 MWe lead-bismuth-cooled, natural-circulation reactor, being studied at JNC, was analyzed. In conclusion, it becomes clear that the combined multi-dimensional plant dynamics code is suitably applicable to analyses of lead-bismuth-cooled, natural-circulation reactors to evaluate thermal-hydraulic phenomena during steady-state and transient conditions. (author)

Remediation potential of mulch for removing lead.

Science.gov (United States)

Jang, A; Bishop, P L

2012-01-01

Hardwood bark mulch has good physicochemical properties for the adsorption of lead (Pb(II)). Batch tests were conducted to obtain the sorption coefficient of Pb(II) in mulch. The results of the Freundlich model were not in as good agreement as for the case of the Langmuir model. In addition, a laboratory-scale mulch permeable reactive barrier (PRB) system was designed for the treatment of Pb(II)-contaminated groundwater. The mulch PRB system, using a mulch layer, can potentially be used in the subsurface for cost-effective and in situ transformation of the Pb(II) into environmentally acceptable forms. From the Pb(II) breakthrough curve, the mulch becomes saturated more quickly at higher flow rates.

Feasibility of lead removal from industrial effluents by sulphate reducing bacteria

International Nuclear Information System (INIS)

Nunez, L. A.; Diez, M.; Rodriguez, F. J.

2009-01-01

Battery manufacturing wastewater contains high concentration of sulphate and lead at low pH values. Biogical treatment by anaerobic reduction of sulphate to sulphite, with organic matter as electron donor, increases alkalinity and allow precipitating lead as sulphide. the type of organic matter, COD/SO 4 ratio and lead concentration over sulphate reduction rate are investigated in this work. (Author)

Assisted phytoremediation of a multi-contaminated soil: Investigation on arsenic and lead combined mobilization and removal.

Science.gov (United States)

Barbafieri, Meri; Pedron, Francesca; Petruzzelli, Gianniantonio; Rosellini, Irene; Franchi, Elisabetta; Bagatin, Roberto; Vocciante, Marco

2017-12-01

The removal of contaminants from an earthy matrix by phytoremediation requires the selection of appropriate plant species and a suitable strategy to be effective. In order to set up an assisted phytoremediation intervention related to a disused industrial site affected by an arsenic and lead complex contamination, an extensive experimental investigation on micro and mesocosm scale has been conducted. Particular attention was given to the choice of plant species: using crop plants (Lupinus albus, Helianthus annuus and Brassica juncea) a series of parallel test campaigns have been realized to investigate different scenarios for the reclamation. With regard to the arsenic contamination, which is certainly the most worrying, the possibility of employing a hyper-accumulator species (Pteris vittata) has also been investigated, highlighting advantages and difficulties associated with such an approach. The application of various mobilizing agents in different concentrations was tested, in order to maximize the extraction efficiency of plants in respect of both contaminants, showing the necessity of a chemically assisted approach to promote their uptake and translocation in the shoots. Phosphate addition appears to produce the desired results, positively affecting As phyto-extraction for both hyper-accumulator and crop plants, while minimizing its toxic effects at the investigated concentrations. With regard to Pb, although tests with EDDS have been encouraging, EDTA should be preferred at present due to lower uncertainties about its effectiveness. The performed tests also improved the addition of mobilizing agents, allowing the simultaneous removal of the two metals despite their great diversity (which in general discourages such approach), with significant saving of time and an obvious improvement of the overall process. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterization of landfill leachates and studies on heavy metal removal.

Science.gov (United States)

Ceçen, F; Gürsoy, G

2000-10-01

This study covers a thorough characterisation of landfill leachates emerging from a sanitary landfill area. The landfill leachates were obtained in the acidic stage of landfill stabilisation. Their organic content was high as reflected by the high BOD5 (5 day biological oxygen demand) and COD (chemical oxygen demand) values. They were also highly polluted in terms of the parameters TKN (total Kjeldahl nitrogen), NH4-N, alkalinity, hardness and heavy metals. Nickel was present in these wastewaters at a significant concentration. With regard to the high heavy metal content of these wastewaters, several physicochemical removal alternatives for the heavy metals Cu, Pb, Zn, Ni, Cd, Cr, Mn and Fe were tested using coagulation, flocculation, precipitation, base addition and aeration. Additionally, COD removal and ammonia stripping were examined. Co-precipitation with either alum or iron salts did not usually lead to significantly higher heavy metal removal than lime alone. The major methods leading to an effective heavy metal removal were aeration and lime addition. Nickel and cadmium seemed to be strongly complexed and were not removed by any method. Also lead removal proved to be difficult. The results are also discussed in terms of compliance with standards.

Study of neutron and gamma shielding by lead borate and bismuth lead borate glasses: transparent radiation shielding

International Nuclear Information System (INIS)

Singh, Vishwanath P.; Badiger, N.M.

2013-01-01

Radiation shielding for gamma and neutron is the prominent area in nuclear reactor technology, medical application, dosimetry and other industries. Shielding of these types of radiation requires an appropriate concrete with mixture of low-to-high Z elements which is an opaque medium. The transparent radiation shielding in visible light for gamma and neutron is also extremely essential in the nuclear facilities as lead window. Presently various types of lead equivalent glass oxides have been invented which are transparent as well as provide protection from radiation. In our study we have assessment of effectiveness of neutron and gamma radiation shielding of xPbO.(1-x) B 2 O 3 (x=0.15 to 0.60) and xBi 2 O 3 .(0.80-x) PbO.0.20 B 2 O 3 (x=0.10 to 0.70) transparent borate and bismuth glasses by NXCOM program. The neutron effective mass removal cross section, Σ R /ρ (cm 2 /g) of the lead, bismuth and boron oxides are given. We found invariable Σ R /ρ of various combinations of the lead borate glass for x=0.15 to 0.60 and bismuth lead borate glass for x=0.10 to 0.70. It is observed that the effective removal cross-section for fast neutron (cm -1 ) of lead borate reduces significantly whereas roughly constant for bismuth borate. The gamma mass attenuation coefficients (μ/ρ) of the glasses were also compared with possible experimental values and found comparable. High (μ/ρ) for gamma radiation of the bismuth glasses shows that it is better gamma shielding compared with lead containing glass. However lead borate glasses are better neutron shielding as the neutron removal coefficient are higher. Our investigation is very useful for nuclear reactor technology where prompt neutron of energy 17 MeV and gamma photon up to 10 MeV produced. (author)

Process for selected gas oxide removal by radiofrequency catalysts

Science.gov (United States)

Cha, Chang Y.

1993-01-01

This process to remove gas oxides from flue gas utilizes adsorption on a char bed subsequently followed by radiofrequency catalysis enhancing such removal through selected reactions. Common gas oxides include SO.sub.2 and NO.sub.x.

Removal of heavy metals from sludge of Sanaru-Lake by electrokinetics

Energy Technology Data Exchange (ETDEWEB)

Seno, T.; Shiba, S.; Hirata, Y. [Dept. of Systems Engineering, Shizuoka Univ., Hamamatsu (Japan)

2001-07-01

Two kinds of experiments were carried out for the removal of heavy metals from soils by electrokinetic technique. One was the removal of lead from kaolinite by using a small-sized test cell. The effect of the kind of purging solutions (such as distilled water, tap water, acetic acid and nitric acid) on removal efficiency was examined. High removal efficiency was obtained for the acetic acid solution. It was found that the controlling pH of solution surrounding cathode had a significant influence on the removal efficiency. The other experiment was the removal of heavy metals from the bottom sludge of Sanaru Lake. Zinc, nickel and copper in the sludge were successfully removed, but lead and chromium were hardly able to remove from the sludge. The simplified one-dimensional mathematical model was proposed. The prediction by the model was qualitatively agreed with the experimental result. (orig.)

Removal of heavy metals and pollutants by membrane adsorption techniques

Science.gov (United States)

Khulbe, K. C.; Matsuura, T.

2018-03-01

Application of polymeric membranes for the adsorption of hazardous pollutants may lead to the development of next-generation reusable and portable water purification appliances. Membranes for membrane adsorption (MA) have the dual function of membrane filtration and adsorption to be very effective to remove trace amounts of pollutants such as cationic heavy metals, anionic phosphates and nitrates. In this review article, recent progresses in the development of MA membranes are surveyed. In addition, recent progresses in the development of advanced adsorbents such as nanoparticles are summarized, since they are potentially useful as fillers in the host membrane to enhance its performance. The future directions of R&D in this field are also shown in the conclusion section.

Nanoscale zero valent supported by Zeolite and Montmorillonite: Template effect of the removal of lead ion from an aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Arancibia-Miranda, Nicolás, E-mail: nicolas.arancibia@usach.cl [Facultad de Química y Biología, CEDENNA, Universidad de Santiago de Chile, USACH, Casilla 40, Santiago C.P. 33 (Chile); Baltazar, Samuel E. [Departamento de Física, CEDENNA, Universidad de Santiago de Chile, USACH, Av. Ecuador 3493, Santiago 9170124 (Chile); García, Alejandra [CIMAV, S.C. Alianza Norte 202, Carretera Monterrey-Aeropuerto Km 10, C.P. 66600, Apodaca Nuevo León (Mexico); University of Texas at San Antonio, Physics and Astronomy Department, One UTSA circle 78249, San Antonio, Texas (United States); Muñoz-Lira, Daniela [Facultad de Química y Biología, CEDENNA, Universidad de Santiago de Chile, USACH, Casilla 40, Santiago C.P. 33 (Chile); Facultad de Ciencias, Universidad de Chile, UCH, Las Palmeras 3425, Santiago 7800024 (Chile); Sepúlveda, Pamela; Rubio, María A. [Facultad de Química y Biología, CEDENNA, Universidad de Santiago de Chile, USACH, Casilla 40, Santiago C.P. 33 (Chile); Altbir, Dora [Departamento de Física, CEDENNA, Universidad de Santiago de Chile, USACH, Av. Ecuador 3493, Santiago 9170124 (Chile)

2016-01-15

composites could be used as an efficient adsorbent for the removal of lead from contaminated water sources.

Synthesis, characterization and application of Lanthanide metal-ion-doped TiO2/bentonite nanocomposite for removal of Lead (II and Cadmium (II from aquatic media

Directory of Open Access Journals (Sweden)

Susan Samadi

2016-07-01

Full Text Available The efficient application of the photocatalytic activity and superficial adsorption on removing heavy metals from water, two types of sorbents, Nd-TiO2/bentonite and Ce-TiO2/bentonite nanocomposites, were synthesized by sol-gel method. The crystalline nanocomposites were obtained after heat treatment at 500 °C for 3 hours. The results of scanning electron microscopy (SEM indicates that Nd-TiO2/bentonite and Ce-TiO2/bentonite were produced on a nanoscale. The phase change of both nanocomposite from amorphous to anatase has been investigated by X- ray diffraction. Removal of lead (II and cadmium (II were studied through adsorption on these nanocomposites by letting them float in the bulk of sample for a definite time in presence and absence of light. The effective parameters in removal process were studied and optimized. The optimum pH, removal time and sorbent dosage in the absence and presence of light for Pb2+ ion were 7, 0.3 g, 15 min and for Cd2+ ion were 7, 0.4 g, 20 min, respectively. Subsequently, the effect of interfering ions in removal process was investigated at optimum conditions and no evidence of interference was observed. The study showed that reproducibility of method (n=9 is good and suitable. The results further indicated that the removal efficiency of Pb2+ ion with Nd-TiO2/bentonite in the presence of light was more than that in the absence of light. Finally, the equilibrium adsorption data fitted Freundlich and Langmuir adsorption models.

Enhanced performance of immobilized laccase in electrospun fibrous membranes by carbon nanotubes modification and its application for bisphenol A removal from water

Energy Technology Data Exchange (ETDEWEB)

Dai, Yunrong, E-mail: daiyr@cugb.edu.cn [School of Water Resources and Environment, School of Scientific Research, China University of Geosciences (Beijing), 100083, Beijing (China); Department of Urban Water Environmental Research, Chinese Research Academy of Environmental Sciences, 100012, Beijing (China); Yao, Jun, E-mail: yaojun@cugb.edu.cn [School of Water Resources and Environment, School of Scientific Research, China University of Geosciences (Beijing), 100083, Beijing (China); Song, Yonghui, E-mail: songyhcraes@gmail.com [Department of Urban Water Environmental Research, Chinese Research Academy of Environmental Sciences, 100012, Beijing (China); Liu, Xiaoling, E-mail: liuxl@craes.org.cn [Department of Urban Water Environmental Research, Chinese Research Academy of Environmental Sciences, 100012, Beijing (China); Wang, Siyu, E-mail: wangsy@craes.org.cn [Department of Urban Water Environmental Research, Chinese Research Academy of Environmental Sciences, 100012, Beijing (China); Yuan, Yu, E-mail: yhzmlyy90311@126.com [Department of Urban Water Environmental Research, Chinese Research Academy of Environmental Sciences, 100012, Beijing (China)

2016-11-05

Highlights: • Both MWCNTs and laccase could be successfully encapsulated into electrospun fibers. • MWCNTs-LCEFMs showed higher activity recovery and better stability than LCEFMs. • Specific surface area and tensile strength of MWCNTs-LCEFMs were also improved. • Addition of MWCNTs enhanced adsorption and removal efficiency of LCEFMs for BPA. • MWCNTs-LCEFMs exhibited better endurance to the change of pH and temperature. - Abstract: Multi-walled carbon nanotubes (MWCNTs) were used as modified materials to improve the performance of laccase-carrying electrospun fibrous membranes (LCEFMs). The MWCNTs modified LCEFMs (MWCNTs-LCEFMs) were successfully fabricated via emulsion electrospinning, with active laccase and MWCNTs encapsulated inside the fibers. After modified by an optimal amount (1.5 wt%, vs. polymer) of MWCNTs, the obtained MWCNTs-LCEFMs showed not only higher activity recovery (85.3%, vs. free laccase) than LCEFMs (71.2%), but also better storage and operational stability, which were mainly attributed to the promoted electron transfer in laccase-catalytic reaction. Furthermore, the specific surface area and tensile strength of MWCNTs-LCEFMs have also been enhanced nearly 2 and 3 times than those of LCEFMs, respectively. The MWCNTs-LCEFMs were applied to remove the widespread bisphenol A from water, where their removal efficiency reached above 90%, with the degradation efficiency accounting for over 80%, and their adsorption efficiency increased about 45% than that of LCEFMs. In addition, the endurances of MWCNTs-LCEFMs to environmental factors such as pH and temperature were also improved.

Enhanced performance of immobilized laccase in electrospun fibrous membranes by carbon nanotubes modification and its application for bisphenol A removal from water

International Nuclear Information System (INIS)

Dai, Yunrong; Yao, Jun; Song, Yonghui; Liu, Xiaoling; Wang, Siyu; Yuan, Yu

2016-01-01

Highlights: • Both MWCNTs and laccase could be successfully encapsulated into electrospun fibers. • MWCNTs-LCEFMs showed higher activity recovery and better stability than LCEFMs. • Specific surface area and tensile strength of MWCNTs-LCEFMs were also improved. • Addition of MWCNTs enhanced adsorption and removal efficiency of LCEFMs for BPA. • MWCNTs-LCEFMs exhibited better endurance to the change of pH and temperature. - Abstract: Multi-walled carbon nanotubes (MWCNTs) were used as modified materials to improve the performance of laccase-carrying electrospun fibrous membranes (LCEFMs). The MWCNTs modified LCEFMs (MWCNTs-LCEFMs) were successfully fabricated via emulsion electrospinning, with active laccase and MWCNTs encapsulated inside the fibers. After modified by an optimal amount (1.5 wt%, vs. polymer) of MWCNTs, the obtained MWCNTs-LCEFMs showed not only higher activity recovery (85.3%, vs. free laccase) than LCEFMs (71.2%), but also better storage and operational stability, which were mainly attributed to the promoted electron transfer in laccase-catalytic reaction. Furthermore, the specific surface area and tensile strength of MWCNTs-LCEFMs have also been enhanced nearly 2 and 3 times than those of LCEFMs, respectively. The MWCNTs-LCEFMs were applied to remove the widespread bisphenol A from water, where their removal efficiency reached above 90%, with the degradation efficiency accounting for over 80%, and their adsorption efficiency increased about 45% than that of LCEFMs. In addition, the endurances of MWCNTs-LCEFMs to environmental factors such as pH and temperature were also improved.

Enhanced high temperature thermoelectric response of sulphuric acid treated conducting polymer thin films

KAUST Repository

Sarath Kumar, S. R.; Kurra, Narendra; Alshareef, Husam N.

2015-01-01

We report the high temperature thermoelectric properties of solution processed pristine and sulphuric acid treated poly(3, 4-ethylenedioxythiophene):poly(4-styrenesulfonate) (or PEDOT:PSS) films. The acid treatment is shown to simultaneously enhance the electrical conductivity and Seebeck coefficient of the metal-like films, resulting in a five-fold increase in thermoelectric power factor (0.052 W/m. K ) at 460 K, compared to the pristine film. By using atomic force micrographs, Raman and impedance spectra and using a series heterogeneous model for electrical conductivity, we demonstrate that acid treatment results in the removal of PSS from the films, leading to the quenching of accumulated charge-induced energy barriers that prevent hopping conduction. The continuous removal of PSS with duration of acid treatment also alters the local band structure of PEDOT:PSS, resulting in simultaneous enhancement in Seebeck coefficient.

Enhanced high temperature thermoelectric response of sulphuric acid treated conducting polymer thin films

KAUST Repository

Sarath Kumar, S. R.

2015-11-24

We report the high temperature thermoelectric properties of solution processed pristine and sulphuric acid treated poly(3, 4-ethylenedioxythiophene):poly(4-styrenesulfonate) (or PEDOT:PSS) films. The acid treatment is shown to simultaneously enhance the electrical conductivity and Seebeck coefficient of the metal-like films, resulting in a five-fold increase in thermoelectric power factor (0.052 W/m. K ) at 460 K, compared to the pristine film. By using atomic force micrographs, Raman and impedance spectra and using a series heterogeneous model for electrical conductivity, we demonstrate that acid treatment results in the removal of PSS from the films, leading to the quenching of accumulated charge-induced energy barriers that prevent hopping conduction. The continuous removal of PSS with duration of acid treatment also alters the local band structure of PEDOT:PSS, resulting in simultaneous enhancement in Seebeck coefficient.

Determining tissue-lead levels in large game mammals harvested with lead bullets: human health concerns.

Science.gov (United States)

Tsuji, L J S; Wainman, B C; Jayasinghe, R K; VanSpronsen, E P; Liberda, E N

2009-04-01

Recently, the use of lead isotope ratios has definitively identified lead ammunition as a source of lead exposure for First Nations people, but the isotope ratios for lead pellets and bullets were indistinguishable. Thus, lead-contaminated meat from game harvested with lead bullets may also be contributing to the lead body burden; however, few studies have determined if lead bullet fragments are present in big game carcasses. We found elevated tissue-lead concentrations (up to 5,726.0 microg/g ww) in liver (5/9) and muscle (6/7) samples of big game harvested with lead bullets and radiographic evidence of lead fragments. Thus, we would advise that the tissue surrounding the wound channel be removed and discarded, as this tissue may be contaminated by lead bullet fragments.

Assessment of the enhanced DHRS configuration for MYRRHA reactor

Energy Technology Data Exchange (ETDEWEB)

Bubelis, E.; Jaeger, W. [KIT, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Bandini, G. [ENEA, via Martiri di Monte Sole, 4, 40129 Bologna (Italy); Alemberti, A.; Palmero, M. [ANSALDO, Corso Perrone 25, 16152 Genova (Italy)

2016-10-15

Highlights: • Innovative decay heat removal system (DHRS). • Heavy liquid metal cooled reactor. • Avoiding of lead bismuth eutectic (LBE) freezing. • Numerical assessment and proof of operational principles of innovative DHRS. - Abstract: This paper deals with the assessment of an innovative decay heat removal system for the MYRRHA reactor, based on the analysis of the selected transients with two different system codes. The application to liquid metal cooled reactors has the disadvantage of adding overcooling transients to the transient spectrum. Under these circumstances, freezing of the coolant can occur if no corrective or operator actions are taken in the medium and long term. Therefore, ANSALDO Nucleare invented an enhanced decay heat removal system which avoids the risk of freezing. The numerical assessment and proof of operational principles are performed by KIT and ENEA. The simulation results show that the freezing can be avoided. Moreover, both institutions calculate similar behavior during overcooling transients. This study will help to implement the novel decay heat removal system and the overall safety philosophy of innovative reactor concepts.

Controlled biomass removal - the key parameter to achieve enhanced biological phosphorus removal in biofilm systems

DEFF Research Database (Denmark)

Morgenroth, E.

1999-01-01

the influence of the following processes on EBPR in biofilms was evaluated: (1) mass transfer limitation for oxygen (2) mass transfer limitation for organic substrate, (3) lack of controlled removal of biomass from the system. It was shown that mass transfer of soluble components (oxygen and organic substrate...

Evaluation of the potentiality of a Mexican natural zeolite chabazite-type in the lead removal in water; Evaluacion de la potencialidad de una chabasita natural mexicana en la remocion de plomo en agua

Energy Technology Data Exchange (ETDEWEB)

Alvarado I, J.; Sotelo L, M.; Meza F, D.; Paz M, F. A. [Universidad de Sonora, Blvd. Luis Encinas y Rosales s/n, Col. Centro, Hermosillo, Sonora (Mexico); Maubert F, M., E-mail: msotelo@guaymas.uson.mx [Universidad Autonoma Metropolitana, Unidad Azcapotzalco, Av. San Pablo 180, Col. Reynosa-Tamaulipas, 02200 Mexico D. F. (Mexico)

2013-06-01

The intention of this paper is to present the characterization of a natural zeolite, chabazite-type, from the Mexican reservoir La Palma, at Divisaderos, Sonora, where their potential use as ion exchange material to remove lead in water is assessed. The chabazite was characterized through X-ray diffraction, Icp-OES, Icp-Ms, EDX, Bet and TG/TGD. The results indicate the presence of Ba(1930 ppm) and Sr(1220 ppm), which are characteristic of aluminium rich phases. A chabazite modification treatment is proposed by using solutions of NaOH (0.1 M) and NH{sub 4}NO{sub 3} (1 M). The lead removal kinetics both in natural zeolite as in their chemically modified forms was obtained by using the ion exchange process in a batch reactor. The results show how unnecessary natural zeolite homo ionization is for the removal of lead, thereby obtaining the equilibrium concentration of unmodified zeolite for plotting the adsorption isotherm, which was adjusted to Langmuir model. The Langmuir isotherm has a good fit of the results at equilibrium (R{sup 2}=0.92), which demonstrates that natural zeolites studied, in its natural form, contains exchangeable cations required (Ca{sup +2}, Mg{sup 2+} and Na{sup +}) for potentially be used as an adsorbent material/ion exchanger for water treatment impacted by lead. (Author)

Graphene-enhanced thermal interface materials for heat removal from photovoltaic solar cells

Science.gov (United States)

Saadah, M.; Gamalath, D.; Hernandez, E.; Balandin, A. A.

2016-09-01

The increase in the temperature of photovoltaic (PV) solar cells affects negatively their power conversion efficiency and decreases their lifetime. The negative effects are particularly pronounced in concentrator solar cells. Therefore, it is crucial to limit the PV cell temperature by effectively removing the excess heat. Conventional thermal phase change materials (PCMs) and thermal interface materials (TIMs) do not possess the thermal conductivity values sufficient for thermal management of the next generation of PV cells. In this paper, we report the results of investigation of the increased efficiency of PV cells with the use of graphene-enhanced TIMs. Graphene reveals the highest values of the intrinsic thermal conductivity. It was also shown that the thermal conductivity of composites can be increased via utilization of graphene fillers. We prepared TIMs with up to 6% of graphene designed specifically for PV cell application. The solar cells were tested using the solar simulation module. It was found that the drop in the output voltage of the solar panel under two-sun concentrated illumination can be reduced from 19% to 6% when grapheneenhanced TIMs are used. The proposed method can recover up to 75% of the power loss in solar cells.

Health care of people at work. Workers exposed to lead. I. Inorganic lead

Energy Technology Data Exchange (ETDEWEB)

Waldron, H.A.

1978-01-01

The risks associated with exposure to inorganic lead and the means by which these risks can be minimized are outlined. Lead is used to make a variety of metal products, the grids and oxides in storage batteries, pigments, chemicals, and also for lead plating. In the United States about 70% of the total lead consumption is related to transportation. Uptake of inorganic lead is by ingestion and inhalation. About 90% of the total body burden of lead is contained within the skeletal tissues. Lead is excreted in the kidney, in sweat, and in milk. Toxic effects are directed against the blood, the nervous system, and the kidney. Symptoms of lead poisoning are abdominal pain, constipation, vomiting, asthenia, paresthesia, psychological symptoms, and diarrhea. Physical and biological monitoring can serve to protect workers. Diagnosis of lead poisoning is not easy. Treatment involves removal from exposure and/or treatment with a chelating agent.

Simultaneous removal of SO{sub 2} and NOx by microwave with potassium permanganate over zeolite

Energy Technology Data Exchange (ETDEWEB)

Zai-shan Wei; He-jingying Niu; Yong-feng Ji [Sun Yat-sen University, Guangzhou (China). School of Environmental Science and Engineering

2009-02-15

Simultaneous sulfur dioxide (SO{sub 2}) and nitrogen oxides (NOx) removal from flue gas can be achieved with high efficiency by microwave with potassium permanganate (KMnO{sub 4}) over zeolite. The experimental results showed that the microwave reactor could be used to oxidation of SO{sub 2} to sulfate with the best desulfurization efficiency of 96.8% and oxidize NOx to nitrates with the best NOx removal efficiency of 98.4%. Microwave accentuates catalytic oxidation treatment, and microwave addition can increase the SO{sub 2} and NOx removal efficiency by 7.2% and 12.2% separately. The addition of zeolite to microwave potassium permanganate increases from 16.5% to 43.5% the microwave removal efficiency for SO{sub 2}, and the NOx removal efficiency from 85.6% to 98.2%. The additional use of potassium permanganate to the microwave zeolite leads to the enhancement of SO{sub 2} removal efficiency up from 53.9% to 95%, and denitrification efficiency up from 85.6% to 98.2%. The optimal microwave power and empty bed residence time (EBRT) on simultaneous desulfurization and denitrification are 259 W and 0.357 s, respectively. SO{sub 2} and NOx were rapidly oxidized in microwave induced catalytic oxidation reaction using potassium permanganate with zeolite being the catalyst and microwave absorbent. 13 refs., 6 figs.

Remediation of cadmium- and lead-contaminated agricultural soil by composite washing with chlorides and citric acid.

Science.gov (United States)

Li, Yu-jiao; Hu, Peng-jie; Zhao, Jie; Dong, Chang-xun

2015-04-01

Composite washing of cadmium (Cd)- and lead (Pb)-contaminated agricultural soil from Hunan province in China using mixtures of chlorides (FeCl3, CaCl2) and citric acid (CA) was investigated. The concentrations of composite washing agents for metal removal were optimized. Sequential extraction was conducted to study the changes in metal fractions after soil washing. The removal of two metals at optimum concentration was reached. Using FeCl3 mixed with CA, 44% of Cd and 23% of Pb were removed, and 49 and 32% by CaCl2 mixed with CA, respectively. The mechanism of composite washing was postulated. A mixture of chlorides and CA enhanced metal extraction from soil through the formation of metal-chloride and metal-citrate complexes. CA in extract solutions promoted the formation of metal-chloride complexes and reduced the solution pH. Composite washing reduced Cd and Pb in Fe-Mn oxide forms significantly. Chlorides and CA exerted a synergistic effect on metal extraction during composite washing.

The Use of Activated Alumina and Magnetic Field for the Removal Heavy Metals from Water

Directory of Open Access Journals (Sweden)

Ewa Szatyłowicz

2018-05-01

Full Text Available The objective of this work was to verify the granular activated alumina (AA sorption properties, during the process of removing copper, lead and cadmium from water, and to monitor the impact of magnetic field (MF on the effectiveness of removing copper, lead and cadmium from water. Activated alumina adsorption is known to be an effective and inexpensive technology for the removal of selenium and arsenic from water and was suggested by EPA as a BAT for point-of-use applications. The removal of copper, lead and cadmium from water using AA and impact of magnetic field was less reported. Pilot tests showed that the use of AA sorption materials with MF impact could possibly decrease the copper, lead and cadmium content in the model water. The MF had also a positive effect on the efficiency of removal copper, lead and cadmium on AA. Increasing the efficiency of heavy metals removal in the samples had been exposed magnetic field varied from 1.9% to 8.2% compared to the control samples.

Laser-based coatings removal

International Nuclear Information System (INIS)

Freiwald, J.G.; Freiwald, D.

1995-01-01

Over the years as building and equipment surfaces became contaminated with low levels of uranium or plutonium dust, coats of paint were applied to stabilize the contaminants in place. Most of the earlier paint used was lead-based paint. More recently, various non-lead-based paints, such as two-part epoxy, are used. For D ampersand D (decontamination and decommissioning), it is desirable to remove the paints or other coatings rather than having to tear down and dispose of the entire building

Lead ions removal from aqueous solution using modified carbon ...

Indian Academy of Sciences (India)

2018-02-02

Feb 2, 2018 ... Recently, in Vietnam and many other countries, the pollution of water by ... ions in water, including copper (Cu2+), lead (Pb2+), cadmium. (Cd2+), zinc (Zn2+) and chromium (Cr3+), may be a potential hazard to human health ...

Reconnecting tile drainage to riparian buffer hydrology for enhanced nitrate removal.

Science.gov (United States)

Jaynes, D B; Isenhart, T M

2014-03-01

Riparian buffers are a proven practice for removing NO from overland flow and shallow groundwater. However, in landscapes with artificial subsurface (tile) drainage, most of the subsurface flow leaving fields is passed through the buffers in drainage pipes, leaving little opportunity for NO removal. We investigated the feasibility of re-routing a fraction of field tile drainage as subsurface flow through a riparian buffer for increasing NO removal. We intercepted an existing field tile outlet draining a 10.1-ha area of a row-cropped field in central Iowa and re-routed a fraction of the discharge as subsurface flow along 335 m of an existing riparian buffer. Tile drainage from the field was infiltrated through a perforated pipe installed 75 cm below the surface by maintaining a constant head in the pipe at a control box installed in-line with the existing field outlet. During 2 yr, >18,000 m (55%) of the total flow from the tile outlet was redirected as infiltration within the riparian buffer. The redirected water seeped through the 60-m-wide buffer, raising the water table approximately 35 cm. The redirected tile flow contained 228 kg of NO. On the basis of the strong decrease in NO concentrations within the shallow groundwater across the buffer, we hypothesize that the NO did not enter the stream but was removed within the buffer by plant uptake, microbial immobilization, or denitrification. Redirecting tile drainage as subsurface flow through a riparian buffer increased its NO removal benefit and is a promising management practice to improve surface water quality within tile-drained landscapes. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Cadmium removal by Euglena gracilis is enhanced under anaerobic growth conditions

Energy Technology Data Exchange (ETDEWEB)

Santiago-Martínez, M. Geovanni; Lira-Silva, Elizabeth; Encalada, Rusely; Pineda, Erika; Gallardo-Pérez, Juan Carlos [Departamento de Bioquímica, Instituto Nacional de Cardiología (Mexico); Zepeda-Rodriguez, Armando [Facultad de Medicina, UNAM, Mexico City (Mexico); Moreno-Sánchez, Rafael; Saavedra, Emma [Departamento de Bioquímica, Instituto Nacional de Cardiología (Mexico); Jasso-Chávez, Ricardo, E-mail: rjass_cardiol@yahoo.com.mx [Departamento de Bioquímica, Instituto Nacional de Cardiología (Mexico)

2015-05-15

Highlights: • The protist Euglena gracilis had the ability to grow and remove large amounts of Cd{sup 2+} under anaerobic conditions. • High biomass was attained by combination of glycolytic and mitochondrial carbon sources. • Routes of degradation of glucose, glutamate and malate under anaerobic conditions in E. gracilis are described. • Biosorption was the main mechanism of Cd{sup 2+} removal in anaerobiosis, whereas the Cd{sup 2+} intracellularly accumulated was inactivated by thiol-molecules and polyphosphate. - Abstract: The facultative protist Euglena gracilis, a heavy metal hyper-accumulator, was grown under photo-heterotrophic and extreme conditions (acidic pH, anaerobiosis and with Cd{sup 2+}) and biochemically characterized. High biomass (8.5 × 10{sup 6} cells mL{sup −1}) was reached after 10 days of culture. Under anaerobiosis, photosynthetic activity built up a microaerophilic environment of 0.7% O{sub 2}, which was sufficient to allow mitochondrial respiratory activity: glutamate and malate were fully consumed, whereas 25–33% of the added glucose was consumed. In anaerobic cells, photosynthesis but not respiration was activated by Cd{sup 2+} which induced higher oxidative stress. Malondialdehyde (MDA) levels were 20 times lower in control cells under anaerobiosis than in aerobiosis, although Cd{sup 2+} induced a higher MDA production. Cd{sup 2+} stress induced increased contents of chelating thiols (cysteine, glutathione and phytochelatins) and polyphosphate. Biosorption (90%) and intracellular accumulation (30%) were the mechanisms by which anaerobic cells removed Cd{sup 2+} from medium, which was 36% higher versus aerobic cells. The present study indicated that E. gracilis has the ability to remove Cd{sup 2+} under anaerobic conditions, which might be advantageous for metal removal in sediments from polluted water bodies or bioreactors, where the O{sub 2} concentration is particularly low.

Cadmium removal by Euglena gracilis is enhanced under anaerobic growth conditions

International Nuclear Information System (INIS)

Santiago-Martínez, M. Geovanni; Lira-Silva, Elizabeth; Encalada, Rusely; Pineda, Erika; Gallardo-Pérez, Juan Carlos; Zepeda-Rodriguez, Armando; Moreno-Sánchez, Rafael; Saavedra, Emma; Jasso-Chávez, Ricardo

2015-01-01

Highlights: • The protist Euglena gracilis had the ability to grow and remove large amounts of Cd 2+ under anaerobic conditions. • High biomass was attained by combination of glycolytic and mitochondrial carbon sources. • Routes of degradation of glucose, glutamate and malate under anaerobic conditions in E. gracilis are described. • Biosorption was the main mechanism of Cd 2+ removal in anaerobiosis, whereas the Cd 2+ intracellularly accumulated was inactivated by thiol-molecules and polyphosphate. - Abstract: The facultative protist Euglena gracilis, a heavy metal hyper-accumulator, was grown under photo-heterotrophic and extreme conditions (acidic pH, anaerobiosis and with Cd 2+ ) and biochemically characterized. High biomass (8.5 × 10 6 cells mL −1 ) was reached after 10 days of culture. Under anaerobiosis, photosynthetic activity built up a microaerophilic environment of 0.7% O 2 , which was sufficient to allow mitochondrial respiratory activity: glutamate and malate were fully consumed, whereas 25–33% of the added glucose was consumed. In anaerobic cells, photosynthesis but not respiration was activated by Cd 2+ which induced higher oxidative stress. Malondialdehyde (MDA) levels were 20 times lower in control cells under anaerobiosis than in aerobiosis, although Cd 2+ induced a higher MDA production. Cd 2+ stress induced increased contents of chelating thiols (cysteine, glutathione and phytochelatins) and polyphosphate. Biosorption (90%) and intracellular accumulation (30%) were the mechanisms by which anaerobic cells removed Cd 2+ from medium, which was 36% higher versus aerobic cells. The present study indicated that E. gracilis has the ability to remove Cd 2+ under anaerobic conditions, which might be advantageous for metal removal in sediments from polluted water bodies or bioreactors, where the O 2 concentration is particularly low

Postmortem analysis of encapsulation around long-term ventricular endocardial pacing leads.

Science.gov (United States)

Candinas, R; Duru, F; Schneider, J; Lüscher, T F; Stokes, K

1999-02-01

To analyze the site and thickness of encapsulation around ventricular endocardial pacing leads and the extent of tricuspid valve adhesion, from today's perspective, with implications for lead removal and sensor location. Gross cardiac postmortem analysis was performed in 11 cases (8 female and 3 male patients; mean age, 78+/-7 years). None of the patients had died because of pacemaker malfunction. The mean implant time was 61+/-60 months (range, 4 to 184). The observations ranged from encapsulation only at the tip of the pacing lead to complete encapsulation along the entire length of the pacing lead within the right ventricle. Substantial areas of adhesion at the tricuspid valve apparatus were noted in 7 of the 11 cases (64%). The firmly attached leads could be removed only by dissection, and in some cases, removal was possible only by damaging the associated structures. No specific optimal site for sensor placement could be identified along the ventricular portion of the pacing leads; however, the fibrotic response was relatively less prominent in the atrial chamber. Extensive encapsulation is present in most long-term pacemaker leads, which may complicate lead removal. The site and thickness of encapsulation seem to be highly variable. Tricuspid valve adhesion, which is usually underestimated, may be severe. In contrast to earlier reports, our study demonstrates that the extent of fibrotic encapsulation may not be related to the duration since lead implantation. Moreover, we noted no ideal encapsulation-free site for sensors on the ventricular portion of long-term pacing leads.

Part 6: Modelling of simultaneous chemical-biological P removal ...

African Journals Online (AJOL)

drinie

approaches taken in modelling the chemical P removal processes. In the literature .... to 2 mgP/l) for an iron dose of ~1 to 10 mg/l as Fe - refer to dashed line in Fig. 1). ...... systems exhibiting biological enhanced phosphate removal. Part 3:.

Space Debris Removal: A Game Theoretic Analysis

Directory of Open Access Journals (Sweden)

Richard Klima

2016-08-01

Full Text Available We analyse active space debris removal efforts from a strategic, game-theoretical perspective. Space debris is non-manoeuvrable, human-made objects orbiting Earth, which pose a significant threat to operational spacecraft. Active debris removal missions have been considered and investigated by different space agencies with the goal to protect valuable assets present in strategic orbital environments. An active debris removal mission is costly, but has a positive effect for all satellites in the same orbital band. This leads to a dilemma: each agency is faced with the choice between the individually costly action of debris removal, which has a positive impact on all players; or wait and hope that others jump in and do the ‘dirty’ work. The risk of the latter action is that, if everyone waits, the joint outcome will be catastrophic, leading to what in game theory is referred to as the ‘tragedy of the commons’. We introduce and thoroughly analyse this dilemma using empirical game theory and a space debris simulator. We consider two- and three-player settings, investigate the strategic properties and equilibria of the game and find that the cost/benefit ratio of debris removal strongly affects the game dynamics.

Evaluation of lead in biological samples treated with radiation

International Nuclear Information System (INIS)

Gomaa, O.M.

1996-01-01

The active dry yeast saccharomyces cerevisiae was able to remove lead successfully from the media. The yeast cells (5 g/100 ml) tolerated up to 8190 ppm lead. The most appropriate conditions for better uptake was when the yeast cells were incubated for 2 hours with different concentrations of lead. Both live and dead cells showed an uptake that exceeded 80% even when there was only 16% of the cells alive. The X RF technique proved that lead is associated with the cells, little, or no lead is found in the media after incubation. Lead bio sorption was investigated in concentrations ranging from 500 to 8000 ppm, the uptake followed the Langmuir and Freundlich adsorption models and was found to be 180 mg/g when the incubation was for 2 h rs. Increasing the concentration of peptone from 0 to 1.5% induced a significant increase in metal removal. Incubating the metal with the cells at 45% showed an uptake that reached 97.44%. Radiation affected the metal uptake to a great extent, increasing the dose of exposure to the cells incubated with lead. led to the increase in the uptake of the metal. When the dose of exposure was 8 kGy, the metal removal reached a maximum of 91% compared to 84 for non-irradiated samples. When the irradiated cells were incubated with lead a variable uptake capacity was observed. When the cells were exposed to 4 kGy, they were capable of removing the metal more efficiently, other exposure doses showed an uptake that was almost the same. Transmission electron microscopy revealed that lead was deposited as electron dense granules around the cells. The EDX identified the metal. The scanning electron microscopy showed that the morphology of the cells was affected when radiation was used, the cells shrunk and lost their ellipsoidal shape, while the addition of lead did not affect their morphology at all

Study on diverse passive decay heat removal approach

International Nuclear Information System (INIS)

Lin Qian; Si Shengyi

2012-01-01

One of the most important principles for nuclear safety is the decay heat removal in accidents. Passive decay heat removal systems are extremely helpful to enhance the safety. In currently design of many advanced nuclear reactors, kinds of passive systems are proposed or developed, such as the passive residual heat removal system, passive injection system, passive containment cooling system. These systems provide entire passive heat removal paths from core to ultimate heat sink. Various kinds of passive systems for decay heat removal are summarized; their common features or differences on heat removal paths and design principle are analyzed. It is found that, these passive decay heat removal paths are similarly common on and connected by several basic heat transfer modes and steps. By the combinations or connections of basic modes and steps, new passive decay heat removal approach or diverse system can be proposed. (authors)

Two cases of acute lead poisoning due to occupational exposure to lead.

Science.gov (United States)

Ogawa, Masanori; Nakajima, Yoshiaki; Kubota, Ryuichi; Endo, Yoko

2008-04-01

We experienced two cases of acute lead poisoning due to occupational exposure to lead. The patients were engaged in stripping off antirust compounds including Pb from a bridge and re-painting it at the same work place. Both patients exhibited colic, arthralgia, and anemia. Blood lead levels were 73.1 microg/dl and 96.3 microg/dl. Intravenous CaEDTA chelation therapy was therefore performed. After chelation, blood lead levels decreased and symptoms gradually disappeared. Although the patients were working with protective equipment, the workplace was in the mountains and there was no water for washing. The patients were thus unable to washing their hands and faces. We assume that they swallowed lead dust left on their hands and faces when they removed their clothing, and believe that this poisoning occurred due to lack of knowledge sufficient for protection.

Comparison of Freezing and Hydrate Formation Methods in Removing Chloride and Bromide Ions from Brine

Directory of Open Access Journals (Sweden)

Marzieh Fattahi

2018-01-01

Full Text Available The growing population and enhanced industrial activities coupled with limitations on freshwater availability have led to efforts to desalinate salt water from the seas. Membrane and thermal technologies are the two commonly used for this purpose. In this study, the direct freezing and hydrate formation techniques were used for salt water desalination. Materials and Methods: Distilled water, sodium chloride, and sodium bromide were used as raw materials in the experiments. The experimental setup included a stationary reactor with two coaxial cylinders, in which ice crystals were deposited outside the cool inner cylinder to increase the salt concentration in the residual brine. An electrical conductivity instrument was used to measure sal removal. Results: Salt removal was shown to decrease with increasing salt concentration in the direct freeze method. A different trend was, however, observed in the hydrate formation method; salt removal was negligible at low concentrations in this method but increased at high concentrations before a constant value was reached. Overall, the hydrate formation recorded a higher salt removal efficiency than the other method. To investigate the effect of anion size on salt removal efficiency, experiments were carried out using NaCl and NaBr, which have the same cation but different anion sizes. Result showed that removal efficiency increased with increasing anion size. Conclusion: It was found that increasing ion radius leads to the lower likelihood of ion presence in the crystal lattice, thereby reducing salt removal efficiency. On the other hand, low concentrations of salt serve as site for the generation of cores, which naturally serve as removal accelerators.

Removal of radionuclides from household water; Metoder foer avlaegsnande av radionuklider fraan hushaallsvatten

Energy Technology Data Exchange (ETDEWEB)

Vesterbacka, P.; Turtiainen, T.; Haemaelaeinen, K.; Salonen, L.; Arvela, H.

2007-02-15

Research upon methods for removing radionuclides from household water was initiated in Finland in 1995. Three research projects, of which two were carried out with National Technology Agency of Finland and one with CEC, have been completed by the end of 2002. One of the main objectives of the research was to compose a guidebook for consumers and water treatment companies. Radon can be removed from household water by aeration and by activated carbon filtration. Aerators that are well designed and set up can remove over 90% of waterborne radon. The best aerators have achieved removal efficiencies that are nearly 100%. However, setting up an aeration system requires thorough planning. Also, activated carbon filtration removes radon efficiently. The removal efficiencies have been over 90%, often nearly 100%. Depending on the water quality and usage, the carbon batch inside the filter needs to be changed every 2 - 3 years. Since activated carbon filters emit gamma radiation while in use, they should not be installed inside the dwelling but in a separate building or by the well. It is recommended that uranium be removed from drinking water by anion exchange, which is the most efficient removal method for this purpose. Typically, the removal efficiencies are nearly 100%. The one exception is the so called tap filter, the removal efficiency of which depends on uranium concentration in raw water and the rate of water flow. High saline concentration in water may extricate uranium from ion exchange resin. Changes in plumbing pressure or pH-value do not have any significant influence in uranium retention. Removal efficiencies of lead and polonium vary a lot depending on the chemical form in which they occur in water. They can be reliably removed from water by reverse osmosis only. Other treatment methods, such as ion exchange and activated carbon filtration, remove lead and polonium partly. Lead and polonium are removed more efficiently when they are bound onto smaller

Photoluminescence Enhancement in Formamidinium Lead Iodide Thin Films

NARCIS (Netherlands)

Fang, Hong-Hua; Wang, Feng; Adjokatse, Sampson; Zhao, Ni; Loi, Maria Antonietta

2016-01-01

Formamidinium lead iodide (FAPbI(3)) has a broader absorption spectrum and better thermal stability than the most famous methylammonium lead iodide, thus exhibiting great potential for photovoltaic applications. In this report, the light-induced photoluminescence (PL) evolution in FAPbI(3) thin

Cyanobacterium removal and control of algal organic matter (AOM) release by UV/H2O2 pre-oxidation enhanced Fe(II) coagulation.

Science.gov (United States)

Jia, Peili; Zhou, Yanping; Zhang, Xufeng; Zhang, Yi; Dai, Ruihua

2017-12-11

Harmful algal blooms in source water are a worldwide issue for drinking water production and safety. UV/H 2 O 2 , a pre-oxidation process, was firstly applied to enhance Fe(II) coagulation for the removal of Microcystis aeruginosa [M. aeruginosa, 2.0 (±0.5) × 10 6  cell/mL] in bench scale. It significantly improved both algae cells removal and algal organic matter (AOM) control, compared with UV irradiation alone (254 nm UVC, 5.4 mJ/cm 2 ). About 94.7% of algae cells were removed after 5 min UV/H 2 O 2 pre-treatment with H 2 O 2 dose 375 μmol/L, FeSO 4 coagulation (dose 125 μmol/L). It was also certified that low residue Fe level and AOM control was simultaneously achieved due to low dose of Fe(II) to settle down the cells as well as the AOM. The result of L 9 (3) 4 orthogonal experiment demonstrated that H 2 O 2 and FeSO 4 dose was significantly influenced the algae removal. UV/H 2 O 2 induced an increase of intracellular reactive oxidant species (ROS) and a decrease in zeta potential, which might contribute to the algae removal. The total microcystins (MCs) concentration was 1.5 μg/L after UV/H 2 O 2 pre-oxidation, however, it could be removed simultaneously with the algae cells and AOM. This study suggested a novel application of UV/H 2 O 2 -Fe(II) process to promote algae removal and simultaneously control AOM release in source waters, which is a green and promising technology without secondary pollution. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bromine pretreated chitosan for adsorption of lead

Indian Academy of Sciences (India)

Pollution by heavy metals like lead (II) is responsible for health hazards and environmental degradation. Adsorption is a prevalent method applied for removal of heavy metal pollutants from water. This study explored adsorption performances of 30% bromine pretreated chitosan for lead (II) abatement from water. Bromine ...

Benefits of integrating chemical and mechanical cleaning processes for steam generator sludge removal

International Nuclear Information System (INIS)

Varrin, R.D.; Ferriter, A.M.; Oliver, T.W.; Le Surf, J.E.

1992-01-01

This paper discusses the benefits of performing in-bundle tubesheet lancing in conjunction with chemical cleaning of PWR and PHWR steam generators in which a hard sludge pile is known to exist. The primary benefits of in-bundle lancing are to: (1) increase the exposed area of the sludge pile by cutting furrows in the surface thereby enhancing dissolution of sludge, (2) reduce the volume of solvents required since material removed by lancing does not have to be dissolved chemically, (3) improve rinsing and removal of residual solvent between iron and copper dissolution steps, and (4) allow for verification of process effectiveness by providing high quality in-bundle visual inspection. The reduction in solvent volumes can lead to a significant reduction in solvent costs and waste processing. A case study which includes an economic evaluation for a combined chemical and mechanical cleaning shows a potential cost saving of up to US$ 300,000 over use of chemical cleaning alone. 14 refs., 2 tabs., 2 figs

Enhanced Removal of Nutrients and Trace Organics from Urban Runoff with Novel Capture, Treatment, and Recharge Systems

Science.gov (United States)

Ashoori, N.; Planes, M. T.; Lefevre, G.; Sedlak, D.; Luthy, R. G.

2017-12-01

Rapid population growth, urban sprawl and impact of climate change are forcing water-stressed areas to rely on new local sources of water supply. Under this scenario, reclamation of stormwater runoff has emerged as a source for irrigation and replenishing drinking-water groundwater reservoirs. However, urban stormwater can be a significant source of pollutants, including nutrients and organic compounds. In order to overcome the stormwater treatment system limitations, this project has developed a pilot-scale column system for passive treatment of infiltrated water using low-cost, low-energy geomedia. The objective was to provide guidance on the design and operation of systems for controlling nutrient and trace organic contaminant releases to surface waters. The work comprised of replicate column studies in the field to test stormwater treatment modules with various media, such as woodchips and biochar, using urban runoff from a watershed in Sonoma, California. Woodchip bioreactors host an endemic population of microorganisms that can be harnessed to biologically degrade nitrate. The columns amended with biochar enhance removal of organic pollutants present in stormwater through physicochemical processes (i.e., adsorption onto biochar) and biodegradation in the column through increasing retention time. The field columns were conditioned with stormwater for eight months before being spiked weekly with 50 ppb of representative trace organics. The key finding was the successful field demonstration of a novel treatment system for both the removal of nitrate and trace organics. Nitrogen removal was successful in all columns for the thirteen month experiment due to the woodchips being an effective source of carbon for denitrifying microorganisms to convert nitrate to nitrogen gases. As for the trace organics experiments, the results highlight an overall attenuation of the studied trace organic compounds by the columns containing woodchip and biochar throughout the five

Enhanced selective removal of Cu(II) from aqueous solution by novel polyethylenimine-functionalized ion imprinted hydrogel: Behaviors and mechanisms.

Science.gov (United States)

Wang, Jingjing; Li, Zhengkui

2015-12-30

A novel polyethylenimine-functionalized ion-imprinted hydrogel (Cu(II)-p(PEI/HEA)) was newly synthesized by (60)Co-γ-induced polymerization for the selective removal of Cu(II) from aqueous solution. The adsorption performances including the adsorption capacity and selectivity of the novel hydrogel were much better than those of similar adsorbents reported. The hydrogel was characterized via scanning electron microscope, transmission electron microscopy, Fourier transform infrared spectra, thermal gravimetric analysis and X-ray photoelectron spectroscopy to determine the structure and mechanisms. The adsorption process was pH and temperature sensitive, better fitted to pseudo-second-order equation, and was Langmuir monolayer adsorption. The maximum adsorption capacity for Cu(II) was 40.00 mg/g. The selectivity coefficients of ion-imprinted hydrogel for Cu(II)/Pb(II), Cu(II)/Cd(II) and Cu(II)/Ni(II) were 55.09, 107.47 and 63.12, respectively, which were 3.93, 4.25 and 3.53 times greater than those of non-imprinted hydrogel, respectively. Moreover, the adsorption capacity of Cu(II)-p(PEI/HEA) could still keep more than 85% after four adsorption-desorption cycles. Because of such enhanced selective removal performance and excellent regeneration property, Cu(II)-p(PEI/HEA) is a promising adsorbent for the selective removal of copper ions from wastewater. Copyright © 2015 Elsevier B.V. All rights reserved.

Enhancement of chitosan-graphene oxide SPR sensor with a multi-metallic layers of Au–Ag–Au nanostructure for lead(II) ion detection

Energy Technology Data Exchange (ETDEWEB)

Kamaruddin, Nur Hasiba [Department of Electric, Electronic and Systems Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor (Malaysia); Bakar, Ahmad Ashrif A., E-mail: ashrif@ukm.edu.my [Department of Electric, Electronic and Systems Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor (Malaysia); Yaacob, Mohd Hanif; Mahdi, Mohd Adzir [Wireless and Photonic Network Research Centre, Faculty of Engineering, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia); Zan, Mohd Saiful Dzulkefly [Department of Electric, Electronic and Systems Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor (Malaysia); Shaari, Sahbudin [Institute of Microengineering and Nanoelectronics, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor (Malaysia)

2016-01-15

Highlights: • Tri-metallic Au–Ag–Au CS-GO SPR sensor was fabricated for the first time. • The tri-metallic nanostructure provided an enhanced evanescent field. • Successful functionalization of the CS-GO sensing layer. • Superior performance for lead(II) ion detection. - Abstract: We demonstrate the enhancement of surface plasmon resonance (SPR) technique by implementing a multi-metallic layers of Au–Ag–Au nanostructure in the chitosan-graphene oxide (CS-GO) SPR sensor for lead(II) ion detection. The performance of the sensor is analyzed via SPR measurements, from which the sensitivity, signal-to-noise ratio and repeatability are determined. The nanostructure layers are characterized using field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). We showed that the proposed structure has increased the shift in the SPR angle up to 3.5° within the range of 0.1–1 ppm due to the enhanced evanescent field at the sensing layer-analyte interface. This sensor also exhibits great repeatability which benefits from the stable multi-metallic nanostructure. The SNR value of 0.92 for 5 ppm lead(II) ion solution and reasonable linearity range up to that concentration shows that the tri-metallic CS-GO SPR sensor gives a good response towards the lead(II) ion solution. The CS-GO SPR sensor is also sensitive to at least a 10{sup −5} change in the refractive index. The results prove that our proposed tri-metallic CS-GO SPR sensor demonstrates a strong performance and reliability for lead(II) ion detection in accordance with the standardized lead safety level for wastewater.

Gas cleaning and hydrogen sulfide removal for COREX coal gas by sorption enhanced catalytic oxidation over recyclable activated carbon desulfurizer.

Science.gov (United States)

Sun, Tonghua; Shen, Yafei; Jia, Jinping

2014-02-18

This paper proposes a novel self-developed JTS-01 desulfurizer and JZC-80 alkaline adsorbent for H2S removal and gas cleaning of the COREX coal gas in small-scale and commercial desulfurizing devices. JTS-01 desulfurizer was loaded with metal oxide (i.e., ferric oxides) catalysts on the surface of activated carbons (AC), and the catalyst capacity was improved dramatically by means of ultrasonically assisted impregnation. Consequently, the sulfur saturation capacity and sulfur capacity breakthrough increased by 30.3% and 27.9%, respectively. The whole desulfurizing process combined selective adsorption with catalytic oxidation. Moreover, JZC-80 adsorbent can effectively remove impurities such as HCl, HF, HCN, and ash in the COREX coal gas, stabilizing the system pressure drop. The JTS-01 desulfurizer and JZC-80 adsorbent have been successfully applied for the COREX coal gas cleaning in the commercial plant at Baosteel, Shanghai. The sulfur capacity of JTS-01 desulfurizer can reach more than 50% in industrial applications. Compared with the conventional dry desulfurization process, the modified AC desulfurizers have more merit, especially in terms of the JTS-01 desulfurizer with higher sulfur capacity and low pressure drop. Thus, this sorption enhanced catalytic desulfurization has promising prospects for H2S removal and other gas cleaning.

Sorption of Lead (II Ions on Activated Coconut Husk

Directory of Open Access Journals (Sweden)

Amin Jahangard

2016-10-01

Full Text Available Background: In recent years, various toxic chemicals/compounds have been widely detected at dangerous levels in drinking water in many parts of the world posing a variety of serious health risks to human beings. One of these toxic chemicals is lead, so this paper aimed to evaluate of efficiency coconut husk as cheap adsorbent for removal lead under different conditions. Methods: In the spring of 2015, batch studies were performed in laboratory (Branch of Hamadan, Islamic Azad University, to evaluate the influences of various experimental parameters like pH, initial concentration, adsorbent dosage, contact time and the effect of temperature on the adsorption capacity of coconut husk for removal lead from aqueous solution. Results: Optimum conditions for Pb (II removal were pH 6, adsorbent dosage 1g/100ml of solution and equilibrium time 120 min. The adsorption isotherm was also affected by temperature since the adsorption capacity was increased by raising the temperature from 25 to 45 °C. The equilibrium adsorption isotherm was better described by Freuindlich adsorption isotherm model. Conclusion: It is evident from the literature survey that coconut-based biosorbents have shown good potential for the removal of various aquatic pollutants. Coconut husk-based activated carbon can be a promising adsorbent for removal of Pb from aqueous solutions.

Unit Process Wetlands for Removal of Trace Organic Contaminants and Pathogens from Municipal Wastewater Effluents

Science.gov (United States)

Jasper, Justin T.; Nguyen, Mi T.; Jones, Zackary L.; Ismail, Niveen S.; Sedlak, David L.; Sharp, Jonathan O.; Luthy, Richard G.; Horne, Alex J.; Nelson, Kara L.

2013-01-01

Abstract Treatment wetlands have become an attractive option for the removal of nutrients from municipal wastewater effluents due to their low energy requirements and operational costs, as well as the ancillary benefits they provide, including creating aesthetically appealing spaces and wildlife habitats. Treatment wetlands also hold promise as a means of removing other wastewater-derived contaminants, such as trace organic contaminants and pathogens. However, concerns about variations in treatment efficacy of these pollutants, coupled with an incomplete mechanistic understanding of their removal in wetlands, hinder the widespread adoption of constructed wetlands for these two classes of contaminants. A better understanding is needed so that wetlands as a unit process can be designed for their removal, with individual wetland cells optimized for the removal of specific contaminants, and connected in series or integrated with other engineered or natural treatment processes. In this article, removal mechanisms of trace organic contaminants and pathogens are reviewed, including sorption and sedimentation, biotransformation and predation, photolysis and photoinactivation, and remaining knowledge gaps are identified. In addition, suggestions are provided for how these treatment mechanisms can be enhanced in commonly employed unit process wetland cells or how they might be harnessed in novel unit process cells. It is hoped that application of the unit process concept to a wider range of contaminants will lead to more widespread application of wetland treatment trains as components of urban water infrastructure in the United States and around the globe. PMID:23983451

Unit Process Wetlands for Removal of Trace Organic Contaminants and Pathogens from Municipal Wastewater Effluents.

Science.gov (United States)

Jasper, Justin T; Nguyen, Mi T; Jones, Zackary L; Ismail, Niveen S; Sedlak, David L; Sharp, Jonathan O; Luthy, Richard G; Horne, Alex J; Nelson, Kara L

2013-08-01

Treatment wetlands have become an attractive option for the removal of nutrients from municipal wastewater effluents due to their low energy requirements and operational costs, as well as the ancillary benefits they provide, including creating aesthetically appealing spaces and wildlife habitats. Treatment wetlands also hold promise as a means of removing other wastewater-derived contaminants, such as trace organic contaminants and pathogens. However, concerns about variations in treatment efficacy of these pollutants, coupled with an incomplete mechanistic understanding of their removal in wetlands, hinder the widespread adoption of constructed wetlands for these two classes of contaminants. A better understanding is needed so that wetlands as a unit process can be designed for their removal, with individual wetland cells optimized for the removal of specific contaminants, and connected in series or integrated with other engineered or natural treatment processes. In this article, removal mechanisms of trace organic contaminants and pathogens are reviewed, including sorption and sedimentation, biotransformation and predation, photolysis and photoinactivation, and remaining knowledge gaps are identified. In addition, suggestions are provided for how these treatment mechanisms can be enhanced in commonly employed unit process wetland cells or how they might be harnessed in novel unit process cells. It is hoped that application of the unit process concept to a wider range of contaminants will lead to more widespread application of wetland treatment trains as components of urban water infrastructure in the United States and around the globe.

Experimental Investigation of Phenanthrene Pollutant Removal Efficiency for Contaminated Sandy Soil by Enhanced Soil Washing

Directory of Open Access Journals (Sweden)

Saif salah Alquzweeni

2016-12-01

Full Text Available Polycyclic aromatic hydrocarbons (PAHs are environmental concerns that must be removed to acceptable level. This research assesses two agents (Na2EDTA and SDS to remediate contaminated sandy soil, spiked with 500mg/kg phenanthrene. Five sets of experiments (batch are applied to investigate the optimal of five influencing factors on soil remediation: Na2EDTA-SDS concentration, liquid/Solid ratio, stirring speed, pH value of flushing solution and mixing time. The results of batch experiments showed that SDS has high phenanthrene removal efficiency (90%, while Na2EDTA shows no phenanthrene removal. pH has no effect on phenanthrene removal. To study the influence of flow rates on the removal efficiency of contaminants, two column tests with hydraulic gradient of 0.2 and 1.2 conducted by SDS solution. The results illustrate that high phenanthrene removal from soil obtained by 1.2 hydraulic gradient condition. The SDS flushing solution removed approximately 69% and 81% of phenanthrene from soil under low and high hydraulic gradients, respectively. It was concluded that phenanthrene removal depend on surfactant micelles formation. Overall, the study showed that soil flushing removal efficiency for contaminants depends on the flushing agents selectivity and affinity to the contaminants and the condition of hydraulic gradient.

Batch versus continuous feeding strategies for pharmaceutical removal by subsurface flow constructed wetland

International Nuclear Information System (INIS)

Zhang Dongqing; Gersberg, Richard M.; Zhu, Junfei; Hua, Tao; Jinadasa, K.B.S.N.; Tan, Soon Keat

2012-01-01

This study evaluated the effect of continuous and batch feeding on the removal of 8 pharmaceuticals (carbamazepine, naproxen, diclofenac, ibuprofen, caffeine, salicylic acid, ketoprofen and clofibric acid) from synthetic wastewater in mesocosm-scale constructed wetlands (CWs). Both loading modes were operated at hydraulic application rates of 5.6 cm day −1 and 2.8 cm day −1 . Except for carbamazepine, clofibric acid and naproxen, removal in CWs was significantly (p ow ) and removal efficiencies of pharmaceutical compounds in the CWs, showed that pharmaceutical removal efficiency was significantly (p ow value, but not with log K ow value. - Highlights: ► Batch feeding in mesocosm-scale constructed wetlands enhances pharmaceutical removal. ► K values for the 8 pharmaceuticals were in the range of 0.01–0.1 m day −1 . ► The pharmaceutical removal efficiency was inversely correlated with log D ow value. - Batch (drain and fill) feeding in mesocosm-scale constructed wetlands enhances pharmaceutical removal.

Remediation of lead-contaminated water by geological fluorapatite and fungus Penicillium oxalicum.

Science.gov (United States)

Tian, Da; Wang, Wenchao; Su, Mu; Zheng, Junyi; Wu, Yuanyi; Wang, Shimei; Li, Zhen; Hu, Shuijin

2018-05-16

Phosphate-solubilizing fungi (PSF) can secrete large amounts of organic acids. In this study, the application of the fungus Penicillium oxalicum and geological fluorapatite (FAp) to lead immobilization was investigated. The formation and morphology of the lead-related minerals were analyzed by ATR-IR, XRD, Raman, and SEM. The quantity of organic acids secreted by P. oxalicum reached the maximum on the fourth day, which elevated soluble P concentrations from 0.4 to 108 mg/L in water. The secreted oxalic acid dominates the acidity in solution. P. oxalicum can survive in the solution with Pb concentration of ~ 1700 mg/L. In addition, it was shown that ~ 98% lead cations were removed while the fungus was cultured with Pb (~ 1700 mg/L) and FAp. The mechanism is that the released P from FAp (enhanced by organic acids) can react with Pb 2+ to form the stable pyromorphite mineral [Pb 5 (PO 4 ) 3 F]. The precipitation of lead oxalate also contributes to Pb immobilization. However, lead oxalate is more soluble due to its relatively high solubility. P. oxalicum has a higher rate of organic acid secretion compared with other typical PSF, e.g., Aspergillus niger. This study sheds light on bright future of applying P. oxalicum in Pb remediation.

Post-treatment of anaerobically degraded azo dye Acid Red 18 using aerobic moving bed biofilm process: Enhanced removal of aromatic amines

International Nuclear Information System (INIS)

Hosseini Koupaie, E.; Alavi Moghaddam, M.R.; Hashemi, S.H.

2011-01-01

Highlights: → Biofilm process was applied as post-treatment of anaerobically degraded an azo dye. → More than 65% of the dye total metabolites was completely mineralized. → Based on HPLC analysis, more than 80% of 1-naphthylamine-4-sulfonate was removed. → Inhibition of biofilm growth was increased with increasing the initial dye concentration. → Considerable porous morphology was observed in the SEM photographs of the biofilm. - Abstract: The application of aerobic moving bed biofilm process as post-treatment of anaerobically degraded azo dye Acid Red 18 was investigated in this study. The main objective of this work was to enhance removal of anaerobically formed the dye aromatic metabolites. Three separate sequential treatment systems were operated with different initial dye concentrations of 100, 500 and 1000 mg/L. Each treatment system consisted of an anaerobic sequencing batch reactor (An-SBR) followed by an aerobic moving bed sequencing batch biofilm reactor (MB-SBBR). Up to 98% of the dye decolorization and more than 80% of the COD removal occurred anaerobically. The obtained results suggested no significant difference in COD removal as well as the dye decolorization efficiency using three An-SBRs receiving different initial dye concentrations. Monitoring the dye metabolites through HPLC suggested that more than 80% of anaerobically formed 1-naphthylamine-4-sulfonate was completely removed in the aerobic biofilm reactors. Based on COD analysis results, at least 65-72% of the dye total metabolites were mineralized during the applied treatment systems. According to the measured biofilm mass and also based on respiration-inhibition test results, increasing the initial dye concentration inhibited the growth and final mass of the attached-growth biofilm in MB-SBBRs.

Preparation of novel oxidized mesoporous carbon with excellent adsorption performance for removal of malachite green and lead ion

Science.gov (United States)

Zhang, Xialan; Lin, Qilang; Luo, Shiyuan; Ruan, Kezhao; Peng, Kaiping

2018-06-01

An oxidized mesoporous carbon (OMC) with fluffy structure was fabricated from the mixture of petroleum asphalt and aluminum isopropoxide, and its structures were characterized by FESEM, TEM, BET, TG, XPS and FT-IR. In addition, bath absorption experiments for malachite green (MG) and lead ion (Pb2+) were carried out to explore the effects of pH, initial concentration, contact time and temperature on its absorption process. Results show that the OMC prepared has a fluffy ultrathin-wall structure with narrow pore size distribution and rich oxygen-containing groups. It exhibits excellent absorption performance for the removal of MG as well as Pb2+, as indicated by that its maximum adsorption capacity is 963.1 mg g-1 for MG and 198.6 mg g-1 for Pb2+. The absorption experimental data are all fitted well with pseudo-second-order model and Frendlich isotherm, respectively. More importantly, the OMC still maintains relatively high adsorption capacity after five cycles.

Study on diverse passive decay heat removal approach and principle

International Nuclear Information System (INIS)

Lin Qian; Si Shengyi

2012-01-01

Decay heat removal in post-accident is one of the most important aspects concerned in the reactor safety analysis. Passive decay heat removal approach is used to enhance nuclear safety. In advanced reactors, decay heat is removed by multiple passive heat removal paths through core to ultimate heat sink by passive residual heat removal system, passive injection system, passive containment cooling system and so on. Various passive decay heat removal approaches are summarized in this paper, the common features and differences of their heat removal paths are analyzed, and the design principle of passive systems for decay heat removal is discussed. It is found that. these decay heat removal paths is combined by some basic heat transfer processes, by the combination of these basic processes, diverse passive decay heat removal approach or system design scheme can be drawn. (authors)

Simultaneous removal of SO{sub 2} and NO{sub x} by microwave with potassium permanganate over zeolite

Energy Technology Data Exchange (ETDEWEB)

Wei, Zai-shan; Niu, He-jingying; Ji, Yong-feng [School of Environmental Science and Engineering, Sun Yat-sen University, Guangzhou 510275 (China)

2009-02-15

Simultaneous sulfur dioxide (SO{sub 2}) and nitrogen oxides (NO{sub x}) removal from flue gas can be achieved with high efficiency by microwave with potassium permanganate (KMnO{sub 4}) over zeolite. The experimental results showed that the microwave reactor could be used to oxidation of SO{sub 2} to sulfate with the best desulfurization efficiency of 96.8% and oxidize NO{sub x} to nitrates with the best NO{sub x} removal efficiency of 98.4%. Microwave accentuates catalytic oxidation treatment, and microwave addition can increase the SO{sub 2} and NO{sub x} removal efficiency by 7.2% and 12.2% separately. The addition of zeolite to microwave potassium permanganate increases from 16.5% to 43.5% the microwave removal efficiency for SO{sub 2}, and the NO{sub x} removal efficiency from 85.6% to 98.2%. The additional use of potassium permanganate to the microwave zeolite leads to the enhancement of SO{sub 2} removal efficiency up from 53.9% to 95%, and denitrification efficiency up from 85.6% to 98.2%. The optimal microwave power and empty bed residence time (EBRT) on simultaneous desulfurization and denitrification are 259 W and 0.357 s, respectively. SO{sub 2} and NO{sub x} were rapidly oxidized in microwave induced catalytic oxidation reaction using potassium permanganate with zeolite being the catalyst and microwave absorbent. (author)

Individual and competitive removal of heavy metals using capacitive deionization

International Nuclear Information System (INIS)

Huang, Zhe; Lu, Lu; Cai, Zhenxiao; Ren, Zhiyong Jason

2016-01-01

Highlights: • Capactive deionization can effectively remove cadmium, lead, and chromium from water. • The removal rates of the individual metal ions vary due to adsorption difference. • The interplay between different metal ions when co-present affects ion removal. - Abstract: This study presents the viability and preference of capacitive deionization (CDI) for removing different heavy metal ions in various conditions. The removal performance and mechanisms of three ions, cadmium (Cd"2"+), lead (Pb"2"+) and chromium (Cr"3"+) were investigated individually and as a mixture under different applied voltages and ion concentrations. It was found that CDI could effectively remove these metals, and the performance was positively correlated with the applied voltage. When 1.2 V was applied into solution containing 0.5 mM individual ions, the Cd"2"+, Pb"2"+, and Cr"3"+ removal was 32%, 43%, and 52%, respectively, and the electrosorption played a bigger role in Cd"2"+ removal than for the other two ions. Interestingly, while the removal of Pb"2"+ and Cr"3"+ remained at a similar level of 46% in the mixture of three ions, the Cd"2"+ removal significantly decreased to 14%. Similar patterns were observed when 0.05 mM was used to simulate natural contaminated water condition, but the removal efficiencies were much higher, with the removal of Pb"2"+, Cr"3"+, and Cd"2"+ increased to 81%, 78%, and 42%, respectively. The low valence charge and lack of physical sorption of Cd"2"+ were believed to be the reason for the removal behavior, and advanced microscopic analysis showed clear deposits of metal ions on the cathode surface after operation.

Lead-cooled flexible conversion ratio fast reactor

International Nuclear Information System (INIS)

Nikiforova, Anna; Hejzlar, Pavel; Todreas, Neil E.

2009-01-01

Lead-cooled reactor systems capable of accepting either zero or unity conversion ratio cores depending on the need to burn actinides or operate in a sustained cycle are presented. This flexible conversion ratio reactor is a pool-type 2400 MWt reactor coupled to four 600 MWt supercritical CO 2 (S-CO 2 ) power conversion system (PCS) trains through intermediate heat exchangers. The cores which achieve a power density of 112 kW/l adopt transuranic metallic fuel and reactivity feedbacks to achieve inherent shutdown in anticipated transients without scram, and lead coolant in a pool vessel arrangement. Decay heat removal is accomplished using a reactor vessel auxiliary cooling system (RVACS) complemented by a passive secondary auxiliary cooling system (PSACS). The transient simulation of station blackout (SBO) using the RELAP5-3D/ATHENA code shows that inherent shutdown without scram can be accommodated within the cladding temperature limit by the enhanced RVACS and a minimum (two) number of PSACS trains. The design of the passive safety systems also prevents coolant freezing in case all four of the PSACS trains are in operation. Both cores are also shown able to accommodate unprotected loss of flow (ULOF) and unprotected transient overpower (UTOP) accidents using the S-CO 2 PCS.

Modified TPA-supported removable pontic

Directory of Open Access Journals (Sweden)

Abhay Kumar Jain

2014-01-01

Full Text Available Missing posterior teeth or necessary asymmetric orthodontic extraction may lead to migration, tilting of the adjacent teeth, and supra-eruption of the opposing teeth along with compromised esthetics. The modified TPA supported removable pontic acts as an esthetic pontic during orthodontic space closure.

Effects of rhamnolipid biosurfactants on removal of phenanthrene from soil

NARCIS (Netherlands)

Noordman, Wouter H.; Ji, Wei; Brusseau, Mark L.; Janssen, Dick B.

1998-01-01

Solubilizing agents may enhance remediation of-soils contaminated with hydrophobic organic contaminants by diminishing sorption of the contaminants or increasing desorption rates. The effectiveness of rhamnolipid biosurfactants to enhance the removal of sorbed contaminants from soil was determined

Lead and zinc removal with storage period in porous asphalt ...

African Journals Online (AJOL)

2013-03-01

Mar 1, 2013 ... total suspended sediments (TSS)), nutrients (e.g., total Kjeldahl nitrogen (TKN)), oil ... (e.g., lead, copper and zinc), are carried by stormwater runoff ..... The essential mineral of limestone ..... kinetics of basalt–water interaction.

Enhanced Stormwater Contaminant Removal and Improved Runoff Quality Using Modified Sorbents in Tree Filters

Science.gov (United States)

Schifman, L. A.; Kasaraneni, V.; Boving, T. B.; Oyanedel-Craver, V.

2013-12-01

Stormwater runoff, particularly in urban areas, contains high concentrations of pathogens that are often cited as one of the main reasons for beach closings and other water quality issues in coastal areas. Commonly found contaminants in runoff are often addressed by structural best management practices (BMP) that capture and treat the runoff before discharging it. Many BMP, such as tree filters, act as primary filtration devices that attenuate total suspended solids, nutrients, and heavy metals from runoff, but typically these BMPs are not designed to treat bacteria and have only minor petroleum hydrocarbon (PH) treatment capabilities. To address this shortcoming, the contaminant retention of an alternative sorption material was compared to expanded shale that is usually used in tree filters. Red cedar wood chips were modified with either Quaternary Ammonium Silane (QAS) or Silver Nanoparticles (AgNPs) to provide antimicrobial properties to the matrix and/or exploit their affinity to sorb PH, particularly polycyclic aromatic hydrocarbons (PAH). Results show that the wood chips exhibit the highest sorption capacity for QAS, making this material favorable for treating bacteria, while at the same time attenuating PAH by sorption processes. In the case of AgNP amendment to wood, less AgNP uptake and more desorption from the wood matrix was observed, making this amendment less favorable for bacteria deactivation. Batch experiments show that wood chips modified with QAS can remove up to 3 orders of magnitude of bacteria and retain up to 0.1 mg/g of PAH compared to shale, which has very limited bacteria deactivation (less than one order of magnitude) a PAH retention capacity of 0.04 mg/g. In this talk, the contaminant removal efficiency of the modified and unmodified materials will be discussed on the background of how these materials may find use in enhanced treatment of stormwater in tree filter BMPs.

Application of chemical oxidation for removal of pharmaceuticals in wastewater effluents

DEFF Research Database (Denmark)

Hey, G.; Ledin, A.; la Cour Jansen, J.

2012-01-01

treatment dose is comparable to ClO2. Nevertheless, ozonation significantly enhanced the removal of most APIs including carbamazepine, metoprolol, flutamide, bupropion and beclomethasone. In addition, ozonation allows removal of ibuprofen at higher oxidant dose. APIs that possess the reactive electron...

Dynamics of Intracellular Polymers in Enhanced Biological Phosphorus Removal Processes under Different Organic Carbon Concentrations

Directory of Open Access Journals (Sweden)

Lizhen Xing

2013-01-01

Full Text Available Enhanced biological phosphorus removal (EBPR may deteriorate or fail during low organic carbon loading periods. Polyphosphate accumulating organisms (PAOs in EBPR were acclimated under both high and low organic carbon conditions, and then dynamics of polymers in typical cycles, anaerobic conditions with excess organic carbons, and endogenous respiration conditions were examined. After long-term acclimation, it was found that organic loading rates did not affect the yield of PAOs and the applied low organic carbon concentrations were advantageous for the enrichment of PAOs. A low influent organic carbon concentration induced a high production of extracellular carbohydrate. During both anaerobic and aerobic endogenous respirations, when glycogen decreased to around 80 ± 10 mg C per gram of volatile suspended solids, PAOs began to utilize polyphosphate significantly. Regressed by the first-order reaction model, glycogen possessed the highest degradation rate and then was followed by polyphosphate, while biomass decay had the lowest degradation rate.

The winner takes it all: Event-related brain potentials reveal enhanced motivated attention toward athletes' nonverbal signals of leading.

Science.gov (United States)

Furley, Philip; Schnuerch, Robert; Gibbons, Henning

2017-08-01

Observers of sports can reliably estimate who is leading or trailing based on nonverbal cues. Most likely, this is due to an adaptive mechanism of detecting motivationally relevant signals such as high status, superiority, and dominance. We reasoned that the relevance of leading athletes should lead to a sustained attentional prioritization. To test this idea, we recorded electroencephalography while 45 participants saw brief stills of athletes and estimated whether they were leading or trailing. Based on these recordings, we assessed event-related potentials and focused on the late positive complex (LPC), a well-established signature of controlled attention to motivationally relevant visual stimuli. Confirming our expectation, we found that LPC amplitude was significantly enhanced for leading as compared to trailing athletes. Moreover, this modulation was significantly related to behavioral performance on the score-estimation task. The present data suggest that subtle cues related to athletic supremacy are reliably differentiated in the human brain, involving a strong attentional orienting toward leading athletes. This mechanism might be part of an adaptive cognitive strategy that guides human social behavior.

Environment-friendly approach for the removal of toxic metals

International Nuclear Information System (INIS)

Zahra, N.; Mehmood, F.; Sheikh, S.T.; Javed, K.; Amin, A.

2006-01-01

Water pollution is serious economical problem and the presence of toxic metals like lead causes contamination of plants and then through nutritional chain it affects the health of humans and animals. This research work describes the removal of lead from wastewater using natural bentonites taken from various areas of Pakistan. The batch adsorption process was applied to remove this toxic metal. The quantities of lead metal before and after the treatment of standard solutions with different samples of bentonite were determined by atomic absorption spectroscopic method. The studies were carried out at room temperature, pH 7 and -200 mesh particle size using 50 ml of metal solutions. The time taken to maintain equilibrium was one hour. Then percentage adsorption was estimated on bentonite samples. (author)

A Critical Assessment of the Microorganisms Proposed to be Important to Enhanced Biological Phosphorus Removal in Full-Scale Wastewater Treatment Systems.

Science.gov (United States)

Stokholm-Bjerregaard, Mikkel; McIlroy, Simon J; Nierychlo, Marta; Karst, Søren M; Albertsen, Mads; Nielsen, Per H

2017-01-01

Understanding the microbiology of phosphorus (P) removal is considered essential to knowledge-based optimization of enhanced biological P removal (EBPR) systems. Biological P removal is achieved in these systems by promoting the growth of organisms collectively known as the polyphosphate accumulating organisms (PAOs). Also considered important to EBPR are the glycogen accumulating organisms (GAOs), which are theorized to compete with the PAOs for resources at the expense of P removal efficiency. Numerous studies have sought to identify the PAOs and their GAOs competitors, with several candidates proposed for each over the last few decades. The current study collectively assessed the abundance and diversity of all proposed PAOs and GAOs in 18 Danish full-scale wastewater treatment plants with well-working biological nutrient removal over a period of 9 years using 16S rRNA gene amplicon sequencing. The microbial community structure in all plants was relatively stable over time. Evidence for the role of the proposed PAOs and GAOs in EBPR varies and is critically assessed, in light of their calculated amplicon abundances, to indicate which of these are important in full-scale systems. Bacteria from the genus Tetrasphaera were the most abundant of the PAOs. The " Candidatus Accumulibacter" PAOs were in much lower abundance and appear to be biased by the amplicon-based method applied. The genera Dechloromonas, Microlunatus , and Tessaracoccus were identified as abundant putative PAO that require further research attention. Interestingly, the actinobacterial Micropruina and sbr-gs28 phylotypes were among the most abundant of the putative GAOs. Members of the genera Defluviicoccus, Propionivibrio , the family Competibacteraceae, and the spb280 group were also relatively abundant in some plants. Despite observed high abundances of GAOs (periodically exceeding 20% of the amplicon reads), P removal performance was maintained, indicating that these organisms were not

Individual and competitive removal of heavy metals using capacitive deionization

Energy Technology Data Exchange (ETDEWEB)

Huang, Zhe; Lu, Lu [Department of Civil, Environmental, and Architectural Engineering, University of Colorado Boulder, Boulder, CO 80309 (United States); Cai, Zhenxiao [Access Business Group LLC, 7575 Fulton Street East, Ada, MI 49301 (United States); Ren, Zhiyong Jason, E-mail: jason.ren@colorado.edu [Department of Civil, Environmental, and Architectural Engineering, University of Colorado Boulder, Boulder, CO 80309 (United States)

2016-01-25

Highlights: • Capactive deionization can effectively remove cadmium, lead, and chromium from water. • The removal rates of the individual metal ions vary due to adsorption difference. • The interplay between different metal ions when co-present affects ion removal. - Abstract: This study presents the viability and preference of capacitive deionization (CDI) for removing different heavy metal ions in various conditions. The removal performance and mechanisms of three ions, cadmium (Cd{sup 2+}), lead (Pb{sup 2+}) and chromium (Cr{sup 3+}) were investigated individually and as a mixture under different applied voltages and ion concentrations. It was found that CDI could effectively remove these metals, and the performance was positively correlated with the applied voltage. When 1.2 V was applied into solution containing 0.5 mM individual ions, the Cd{sup 2+}, Pb{sup 2+}, and Cr{sup 3+} removal was 32%, 43%, and 52%, respectively, and the electrosorption played a bigger role in Cd{sup 2+} removal than for the other two ions. Interestingly, while the removal of Pb{sup 2+} and Cr{sup 3+} remained at a similar level of 46% in the mixture of three ions, the Cd{sup 2+} removal significantly decreased to 14%. Similar patterns were observed when 0.05 mM was used to simulate natural contaminated water condition, but the removal efficiencies were much higher, with the removal of Pb{sup 2+}, Cr{sup 3+}, and Cd{sup 2+} increased to 81%, 78%, and 42%, respectively. The low valence charge and lack of physical sorption of Cd{sup 2+} were believed to be the reason for the removal behavior, and advanced microscopic analysis showed clear deposits of metal ions on the cathode surface after operation.

Technetium removal from aqueous wastes

International Nuclear Information System (INIS)

Fletcher, P.A.; Jones, C.P.; Junkison, A.R.; Turner, A.D.; Kavanagh, P.R.

1992-03-01

The research discussed in this report has compared several ''state of the art'' techniques for the removal of traces of the radionuclide, technetium, from aqueous wastes. The techniques investigated were: electrochemical reduction to an insoluble oxide, electrochemical ion exchange, seeded ultrafiltration and chemical reduction followed by filtration. Each technique was examined using a simulant based upon the waste generated by the Enhanced Actinide Removal Plant (EARP) at Sellafield. The technique selected for further investigation was direct electrochemical reduction which offers an ideal route for the removal of technetium from the stream (DFs 10-100) and can be operated continuously with a low power consumption 25 kW for the waste generated by EARP. Cell designs for scale up have been suggested to treat the 1000m 3 of waste produced every day. Future work is proposed to investigate the simultaneous removal of other key radionuclides, such as ruthenium, plutonium and cobalt as well as scale up of the resulting process and to investigate the effect of these other radionuclides on the efficiency of the electrochemical reduction technique for the removal of technetium. Total development and full scale plant costs are estimated to be of the order of 5 pounds - 10M, with a time scale of 5 -8 years to realisation. (author)

Multilayer Substrate Configuration Enhances Removal Efficiency of Pollutants in Constructed Wetlands

Directory of Open Access Journals (Sweden)

Shaoyuan Bai

2016-11-01

Full Text Available This study aimed at optimizing horizontal subsurface flow constructed wetlands (CWs to improve hydraulic performance and pollutant removal efficiency. A groundwater modeling package (MODFLOW was used to optimize three design parameters (length-to-width ratio, inlet/outlet-to-length ratio, and substrate size configuration. Using the optimized parameters, three pilot-scale CWs were built to treat actual wastewater. For model validation, we used a tracer test to evaluate hydraulic performance, and investigated the pollutant spatial distributions and removal efficiencies. We conclude that MODFLOW is suitable for designing CWs, accurately predicting that increasing hydraulic conductivity from surface to bottom layers could improve performance. However, the effect of vegetation, which decreased the hydraulic conductivity of the surface layer, should be considered to improve simulation results. Multilayer substrate configuration, with increasing hydraulic conductivity from the surface to bottom layers, significantly increased pollutant removal compared with monolayer configuration. The spatial variation in pollutant transport and degradation through the filling substrate showed that the multilayer configuration was able to increase use of the available space and moderately reduced short-circuiting and dead zones. Thus, multilayer CWs had higher experimental retention times, effective volume fractions and hydraulic efficiencies, and lower short-circuiting compared with monolayer CWs operating under similar conditions.

Secondary lead production

Energy Technology Data Exchange (ETDEWEB)

Hollis, R.G.

1990-10-16

This invention is concerned with the efficient recovery of soft lead from the paste component of used automobile lead-acid storage batteries. According to the invention, a scrap which contains lead oxide, lead sulfate, and antimony in an oxidized state is processed in the following steps to recover lead. A refractory lined reaction vessel is continuously charged with the scrap, along with a reductant effective for reducing lead oxide. The charged material is melted and agitated by means of a submerged lance at 900-1150{degree}C whereby some of the lead oxide of the scrap is reduced to form molten lead. A slag layer is then formed above the molten lead, and an amount of lead oxide is maintained in the slag layer. The molten lead, now containing under 0.5 wt % of antimony, is removed, and the antimony oxide in the scrap is concentrated as oxide in the slag layer. Preferred embodiments of the invention result in the production, in a single step, of a soft lead substantially free of antimony. The slag may be subsequently treated to reduce the antimony oxide and produce a valuable antimony-lead product. Further advantages of the process are that a wet battery paste may be used as the feed without prior drying, and the process can be conducted at a temperature 100-150{degree}C lower than in previously known methods. In addition, a smaller reactor can be employed which reduces both capital cost and fuel costs. The process of the invention is illustrated by descriptions of pilot plant tests. 1 fig.

Enhanced removal of Cd(II) and Pb(II) by composites of mesoporous carbon stabilized alumina

Energy Technology Data Exchange (ETDEWEB)

Yang, Weichun [Department of Environmental Engineering, School of Metallurgy and Environment, Central South University, Lushan South Road 932, Changsha 410017 (China); Chinese National Engineering Research Center for Control & Treatment of Heavy Metal Pollution, Lushan South Road 932, Changsha 410017 (China); Tang, Qiongzhi; Wei, Jingmiao; Ran, Yajun [Department of Environmental Engineering, School of Metallurgy and Environment, Central South University, Lushan South Road 932, Changsha 410017 (China); Chai, Liyuan [Department of Environmental Engineering, School of Metallurgy and Environment, Central South University, Lushan South Road 932, Changsha 410017 (China); Chinese National Engineering Research Center for Control & Treatment of Heavy Metal Pollution, Lushan South Road 932, Changsha 410017 (China); Wang, Haiying, E-mail: haiyw25@163.com [Department of Environmental Engineering, School of Metallurgy and Environment, Central South University, Lushan South Road 932, Changsha 410017 (China); Chinese National Engineering Research Center for Control & Treatment of Heavy Metal Pollution, Lushan South Road 932, Changsha 410017 (China)

2016-04-30

Graphical abstract: - Highlights: • Mesoporous carbon stabilized alumina was prepared by one-pot hard-templating method. • MC/Al{sub 2}O{sub 3} showed excellent performance for Cd(II) and Pb(II) adsorption. • Enhanced adsorption was due to the high surface area and special functional groups. - Abstract: A novel adsorbent of mesoporous carbon stabilized alumina (MC/Al{sub 2}O{sub 3}) was synthesized through one-pot hard-templating method. The adsorption potential of MC/Al{sub 2}O{sub 3} for Cd(II) and Pb(II) from aqueous solution was investigated compared with the mesoporous carbon. The results indicated the MC/Al{sub 2}O{sub 3} showed excellent performance for Cd(II) and Pb(II) removal, the adsorption capacity reached 49.98 mg g{sup −1} for Cd(II) with initial concentration of 50 mg L{sup −1} and reached 235.57 mg g{sup −1} for Pb(II) with initial concentration of 250 mg L{sup −1}, respectively. The kinetics data of Cd(II) adsorption demonstrated that the Cd(II) adsorption rate was fast, and the removal efficiencies with initial concentration of 10 and 50 mg L{sup −1} can reach up 99% within 5 and 20 min, respectively. The pseudo-second-order kinetic model could describe the kinetics of Cd(II) adsorption well, indicating the chemical reaction was the rate-controlling step. The mechanism for Cd(II) and Pb(II) adsorption by MC/Al{sub 2}O{sub 3} was investigated by X-ray photoelectron spectroscopy (XPS) and Fourier transformed infrared spectroscopy (FTIR), and the results indicated that the excellent performance for Cd(II) and Pb(II) adsorption of MC/Al{sub 2}O{sub 3} was mainly attributed to its high surface area and the special functional groups of hydroxy-aluminum, hydroxyl, carboxylic through the formation of strong surface complexation or ion-exchange. It was concluded that MC/Al{sub 2}O{sub 3} can be recognized as an effective adsorbent for removal of Cd(II) and Pb(II) in aqueous solution.

Enhanced Removal of Trichloroethylene in Water Using Nano-ZnO/Polybutadiene Rubber Composites

Directory of Open Access Journals (Sweden)

Dae Gyu Jang

2016-09-01

Full Text Available An innovative nanoscale ZnO/polybutadiene rubber composite (ZBRC was developed as a valid alternative to TiO2 particles or immobilized TiO2 for the mineralization of chlorinated hydrocarbons without difficulties in the recovery of nanoscale photocatalyst particles. A synergistic increase in the removal of 1,1,2-trichloroethylene (TCE through the coupled reaction processes (i.e., sorption, photolysis, and photocatalysis was observed because sorption of TCE to the ultraviolet(UV-transparent polybutadiene rubber occurred, and was coupled with the heterogeneous photocatalytic reactions with nanoscale ZnO particles on the surface of ZBRC. The removal rate of TCE decreased with an increase in the initial concentration of TCE because of both inhibited generation of electron–hole pairs and deficiency of photons to activate ZnO particles. Also, the TCE removal rate increased as the loading amount of ZBRC increased. Based on satisfactory linear regressions (R2 ≥ 0.94 between the apparent degradation rate constant (Kapp and the initial concentration vs. the ZBRC loading amount, the Kapp values can be estimated, a priori, without performing photocatalytic experiments. The removal efficiencies were more significantly affected by the changes in the initial concentration of TCE and the ZBRC loading amounts than by the changes in light intensity and pH in aqueous solutions. From the results of response surface analysis, the greater removal efficiencies of TCE were achieved with higher pH values, greater amounts of ZBRC, and greater intensity of light. Based on these results, newly-developed ZBRC with both high removal efficiency and low cost performs as a valid alternative to TiO2 particles or immobilized TiO2 for the mineralization of chlorinated hydrocarbons in various environmental and industrial matrices.

Application of electrochemical technology for removing petroleum hydrocarbons from produced water using lead dioxide and boron-doped diamond electrodes.

Science.gov (United States)

Gargouri, Boutheina; Gargouri, Olfa Dridi; Gargouri, Bochra; Trabelsi, Souhel Kallel; Abdelhedi, Ridha; Bouaziz, Mohamed

2014-12-01

Although diverse methods exist for treating polluted water, the most promising and innovating technology is the electrochemical remediation process. This paper presents the anodic oxidation of real produced water (PW), generated by the petroleum exploration of the Petrobras plant-Tunisia. Experiments were conducted at different current densities (30, 50 and 100 mA cm(-2)) using the lead dioxide supported on tantalum (Ta/PbO2) and boron-doped diamond (BDD) anodes in an electrolytic batch cell. The electrolytic process was monitored by the chemical oxygen demand (COD) and the residual total petroleum hydrocarbon [TPH] in order to know the feasibility of electrochemical treatment. The characterization and quantification of petroleum wastewater components were performed by gas chromatography mass spectrometry. The COD removal was approximately 85% and 96% using PbO2 and BDD reached after 11 and 7h, respectively. Compared with PbO2, the BDD anode showed a better performance to remove petroleum hydrocarbons compounds from produced water. It provided a higher oxidation rate and it consumed lower energy. However, the energy consumption and process time make useless anodic oxidation for the complete elimination of pollutants from PW. Cytotoxicity has shown that electrochemical oxidation using BDD could be efficiently used to reduce more than 90% of hydrocarbons compounds. All results suggest that electrochemical oxidation could be an effective approach to treat highly concentrated organic pollutants present in the industrial petrochemical wastewater and significantly reduce the cost and time of treatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

When does invasive species removal lead to ecological recovery? Implications for management success

Science.gov (United States)

Kirsten M. Prior; Damian C. Adams; Kier D. Klepzig; Jiri Hulcr

2018-01-01

The primary goal of invasive species management is to eliminate or reduce populations of invasive species. Although management efforts are often motivated by broader goals such as to reduce the negative impacts of invasive species on ecosystems and society, there has been little assessment of the consistency between population-based (e.g., removing invaders) and...

Cd(II) removal and recovery enhancement by using acrylamide–titanium nanocomposite as an adsorbent

International Nuclear Information System (INIS)

Sharma, Ajit; Lee, Byeong-Kyu

2014-01-01

Graphical abstract: - Highlights: • Acrylamide doping initiated 10–20% increase in the particle size. • R-NH 2 Cd 2+ and Cd-O onto the nanocomposite improved Cd(II) adsorption. • Coexisting cations did not make any significant interference of Cd(II) removal. • Increased Ti nanoparticles leads to decrease in mass swelling of acrylamide. - Abstract: Acrylamide (AM) was in-situ doped into titanium during sol–gel reaction and used as an adsorbent for cadmium removal from aqueous solution. The resulting TiO 2 -AM nanocomposite was characterized by particle size distribution (PSD) and thermogravimetric analysis (TGA). After cadmium adsorption, the nanocomposite was also characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy/energy-dispersive X-ray (SEM/EDX) and X-ray photoelectron spectroscopy (XPS) analyses. The adsorption behavior of the nanocomposite was examined by kinetic and equilibrium studies in batch conditions. The maximum cadmium binding capacity of TiO 2 -AM was 322.58 mg g −1 at an optimum pH of 8.0, compared to 86.95 mg g −1 for nano-titanium. Cadmium sorption showed pseudo-second-order kinetics with a rate constant of 4.0 × 10 −4 and 9.4 × 10 −5 g mg −1 min −1 at an initial Cd(II) concentration of 100 and 500 mg L −1 , respectively. Cd (II) adsorption interference of cations (Pb 2+ , Cu 2+ , Co 2+ and Zn +2 ) and anions (Cl − , SO 4 2− , CO 3 2− ) at pH 8 was very nominal because of favorable complex formation of Cd(II) and amide. The Cd(II) adsorption of 27% that was achieved in the fifth cycle was regenerated with 0.05 N acidic solutions

Intensive mutagenesis of the nisin hinge leads to the rational design of enhanced derivatives.

Directory of Open Access Journals (Sweden)

Brian Healy

Full Text Available Nisin A is the most extensively studied lantibiotic and has been used as a preservative by the food industry since 1953. This 34 amino acid peptide contains three dehydrated amino acids and five thioether rings. These rings, resulting from one lanthionine and four methyllanthionine bridges, confer the peptide with its unique structure. Nisin A has two mechanisms of action, with the N-terminal domain of the peptide inhibiting cell wall synthesis through lipid II binding and the C-terminal domain responsible for pore-formation. The focus of this study is the three amino acid 'hinge' region (N 20, M 21 and K 22 which separates these two domains and allows for conformational flexibility. As all lantibiotics are gene encoded, novel variants can be generated through manipulation of the corresponding gene. A number of derivatives in which the hinge region was altered have previously been shown to possess enhanced antimicrobial activity. Here we take this approach further by employing simultaneous, indiscriminate site-saturation mutagenesis of all three hinge residues to create a novel bank of nisin derivative producers. Screening of this bank revealed that producers of peptides with hinge regions consisting of AAK, NAI and SLS displayed enhanced bioactivity against a variety of targets. These and other results suggested a preference for small, chiral amino acids within the hinge region, leading to the design and creation of producers of peptides with hinges consisting of AAA and SAA. These producers, and the corresponding peptides, exhibited enhanced bioactivity against Lactococcus lactis HP, Streptococcus agalactiae ATCC 13813, Mycobacterium smegmatis MC2155 and Staphylococcus aureus RF122 and thus represent the first example of nisin derivatives that possess enhanced activity as a consequence of rational design.

Arsenic removal by magnetic nanocrystalline barium hexaferrite

International Nuclear Information System (INIS)

Patel, Hasmukh A.; Byun, Jeehye; Yavuz, Cafer T.

2012-01-01

Nanoscale magnetite (Fe 3 O 4 ) ( 12 O 19 , BHF) is a well-known permanent magnet (i.e., fridge magnets) and attractive due to its low cost in making large quantities. BHF offers a viable alternative to magnetite nanocrystals for arsenic removal since it features surfaces similar to iron oxides but with much enhanced magnetism. Herein, we employ BHF nanocrystalline materials for the first time in arsenic removal from wastewater. Our results show better (75 %) arsenic removal than magnetite of the similar sizes. The BHF nanoparticles, 6.06 ± 0.52 nm synthesized by thermolysis method at 320 °C do not show hexagonal phase, however, subsequent annealing at 750 °C produced pure hexagonal BHF in >200 nm assemblies. By using BHF, we demonstrate that nanoparticle removal is more efficient and fixed bed type cartridge applications are more possible.

Sequestration Resins for Accelerating Removal of Radioactive Contaminants

International Nuclear Information System (INIS)

Frattini, Paul-L.; Wells, Daniel-M.; Garcia, Susan-E.; Richard, Kohlmann; Asay, Roger; Yengoyan, Leon

2012-09-01

The Electric Power Research Institute (EPRI) is developing sequestration resins that can be used in the treatment of nuclear plant water streams for the enhanced removal of ionic cobalt. EPRI is focusing on three key areas of success: 1. Plant safety. The resins that are synthesized must be fully tested to determine that no leachable species or decomposition products (in the event of a resin bed failure) would be introduced to the plant. 2. Acceptable system performance. The resins are currently being synthesized in a powdered form for use in the reactor water clean-up and fuel pool clean-up systems that utilize pre-coatable filter elements. The resins must have effective flocking behavior; uniform application over the underlay resin and efficient removal from the septa elements after use. Bead type resins are also under development. 3. Enhanced cobalt removal. The resins are expected to out-perform the currently used ion exchange resins in the removal of ionic cobalt. During nuclear plant maintenance or refueling outages, current ion exchange resins may require several days to reduce concentrations of cobalt (for example, radio-cobalt 60 Co and 58 Co) and other activated corrosion products to safe levels in reactor coolant streams. This performance limitation often delays key maintenance activities. EPRI's resins are expected to provide at least a three-fold increase in removal capacity in light water reactor coolants. These resins also offer the potential for higher overall removal efficiencies reducing occupational exposures and waste management costs. This paper addresses issues from the range of novel resin development for radio-cobalt removal from synthesis at the bench-top level through scale-up to demonstration of use in an actual operating nuclear power plant. (authors)

Removal of trace metal contaminants from potable water by electrocoagulation

OpenAIRE

Heffron, Joe; Marhefke, Matt; Mayer, Brooke K.

2016-01-01

This study investigated the effects of four operational and environmental variables on the removal of trace metal contaminants from drinking water by electrocoagulation (EC). Removal efficiencies for five metals (arsenic, cadmium, chromium, lead and nickel) were compared under varying combinations of electrode material, post-treatment, water composition and pH. Iron electrodes out-performed aluminum electrodes in removing chromium and arsenic. At pH 6.5, aluminum electrodes were slightly more...

Meson-Exchange Enhancement of First-Forbidden $\\beta$-Transitions in the Lead Region

CERN Multimedia

Delaure, B J P; Severijns, N

2002-01-01

Both on-line and off-line low temperature nuclear orientation is used to measure the $\\beta$-asymmetry parameter for the first-forbidden g.s. $\\rightarrow$~g.s. $\\beta$-transitions of $^{205}$Hg, $^{207,209}$Tl, $^{209}$Pb and $^{213}$Bi. From this, the ratio of the rank-zero and the rank-one strengths in these decays can be deduced, with the rank of a $\\beta$-transition being defined as the total angular momentum of the lepton system. Combining this result with the experimental ${ft}$-values yields for the first time a purely experimental determination of the rank-zero contribution in these $\\Delta$ J = 0 first-forbidden transitions. This provides an independent check of the large enhancement (of about 100% over the impulse approximation) of the rank-zero matrix element of $\\gamma_{5} $, caused by meson exchange currents (MEC), which was recently obtained from a comparison of calculated first-forbidden $\\beta$-decay rates with experimentally observed values for nuclei in the lead region (A = 205-212). Measur...

Adsorption Study on Moringa Oleifera Seeds and Musa Cavendish as Natural Water Purification Agents for Removal of Lead, Nickel and Cadmium from Drinking Water

Science.gov (United States)

Aziz, N. A. A.; Jayasuriya, N.; Fan, L.

2016-07-01

The effectiveness of plant based materials Moringa oleifera (Moringa) seeds and Musa cavendish (banana peel) for removing heavy metals namely lead (Pb), nickel (Ni) and cadmium (Cd) from contaminated groundwater was studied. Tests were carried out with individual and combined biomass at neutral pH condition on synthetic groundwater samples. The optimum biomass doses were determined as 200 mg/L for single biomass and 400 mg/L (in the ratio of 200 mg/L: 200 mg/L) for combined biomasses and used for adsorption isotherm studies with contact time of 30 minutes. Results showed that combined biomasses was able to met the Pb, Ni and Cd WHO standards from higher Pb, Ni and Cd initial concentrations which were up to 40 µg/L, 50 µg/L 9 µg/L, respectively compared to individual biomass of Moringa seed and banana peel. Moringa seeds exhibited the highest removal of Pb (81%) while the combined biomasses was most effective in removing Ni (74%) and Cd (97%) over wider their initial concentration ranges. The experimental data were linearized with Langmuir and Freundlich adsorption isotherm models. Freundlich model described the Pb adsorption better than the Langmuir model for all the tested biomasses. However, the Langmuir model fit better with the experimental data of Ni adsorption by Moringa seeds. Both models showed negligible differences in the coefficient of determination (R2) when applied for Ni and Cd adsorption on banana peel and combined biomasses, suggesting that there were multiple layers on the biomass interacting with the metals. Chemisorption is suggested to be involved in Pb adsorption for all tested biomasses as the value of nF calculated was lower than one. This type of adsorption could explain the phenomenon of different behavior of Pb removal and the higher Pb adsorption capacity (represented by KF values) compared to Ni and Cd. The study demonstrates that Moringa seeds, banana peel and their combination have the potential to be used as a natural alternative

Lead poisoning in dogs

International Nuclear Information System (INIS)

Zook, B.C.; Carpenter, J.L.; Leeds, E.B.

1969-01-01

Lead poisoning was diagnosed and studied in 60 dogs. It was found that lead poisoning is a common disease of young dogs, especially in the summer and fall, and is related to their chewing and eating habits resulting in the ingestion of paint, linoleum, or other lead-containing materials. The signs were characterized by gastrointestinal dysfunction (colic, vomiting, and diarrhea) and nervous disorders (convulsions, hysteria, nervousness, behavioral changes). The blood findings, which the authors consider nearly pathognomonic, consisted of numerous stippled and immature (especially nucleated) erythrocytes in the absence of severe anemia. Protein and casts were frequently found in the urine. Radiography sometimes revealed lead-containing particles in the gastro-intestinal tract, and lead lines were occasionally detected in the metaphysis of long bones in immature dogs. Treatment with calcium ethylenediamine-tetraacetic acid resulted in rapid and often dramatic recoveries in nearly all instances. Removal of lead from the gastrointestinal tract and treatment to relieve pronounced central nervous disorders was sometimes necessary. 40 references, 6 figures, 7 tables

Delayed and successful manual removal of abnormally adherent ...

African Journals Online (AJOL)

manual removal necessitated by uterine sepsis following conservative management with methotrexate was completely successful. ... Current aetiological concepts include abnormal ... reveal an AAP leading to profuse uterine bleeding.

Improved Electrocoagulation Reactor for Rapid Removal of Phosphate from Wastewater

KAUST Repository

Tian, Yushi

2016-11-01

A new three-electrode electrocoagulation reactor was investigated to increase the rate of removal of phosphate from domestic wastewater. Initially, two electrodes (graphite plate and air cathode) were connected with 0.5 V of voltage applied for a short charging time (∼10 s). The direction of the electric field was then reversed, by switching the power supply lead from the anode to the cathode, and connecting the other lead to a sacrificial aluminum mesh anode for removal of phosphate by electrocoagulation. The performance of this process, called a reverse-electric field, air cathode electrocoagulation (REAEC) reactor, was tested using domestic wastewater as a function of charging time and electrocoagulation time. REAEC wastewater treatment removed up to 98% of phosphate in 15 min (inert electrode working time of 10 s, current density of 1 mA/cm2, and 15 min total electrocoagulation time), which was 6% higher than that of the control (no inert electrode). The energy demand varied from 0.05 kWh/m3 for 85% removal in 5 min, to 0.14 kwh/m3 for 98% removal in 15 min. These results indicate that the REAEC can reduce the energy demands and treatment times compared to conventional electrocoagulation processes for phosphate removal from wastewater.

Enhanced removal of aqueous acetaminophen by a laccase-catalyzed oxidative coupling reaction under a dual-pH optimization strategy.

Science.gov (United States)

Wang, Kaidong; Huang, Ke; Jiang, Guoqiang

2018-03-01

Acetaminophen is one kind of pharmaceutical contaminant that has been detected in municipal water and is hard to digest. A laccase-catalyzed oxidative coupling reaction is a potential method of removing acetaminophen from water. In the present study, the kinetics of radical polymerization combined with precipitation was studied, and the dual-pH optimization strategy (the enzyme solution at pH7.4 being added to the substrate solution at pH4.2) was proposed to enhance the removal efficiency of acetaminophen. The reaction kinetics that consisted of the laccase-catalyzed oxidation, radical polymerization and precipitation were studied by UV in situ, LC-MS and DLS (dynamic light scattering) in situ. The results showed that the laccase-catalyzed oxidation is the rate-limiting step in the whole process. The higher rate of enzyme-catalyzed oxidation under a dual-pH optimization strategy led to much faster formation of the dimer, trimer and tetramer. Similarly, the formation of polymerized products that could precipitate naturally from water was faster. Under the dual-pH optimization strategy, the initial laccase activity was increased approximately 2.9-fold, and the activity remained higher for >250s, during which approximately 63.7% of the total acetaminophen was transformed into biologically inactive polymerized products, and part of these polymerized products precipitated from the water. Laccase belongs to the family of multi-copper oxidases, and the present study provides a universal method to improve the activity of multi-copper oxidases for the high-performance removal of phenol and its derivatives. Copyright © 2017 Elsevier B.V. All rights reserved.

[Remediation efficiency of lead-contaminated soil at an industrial site by ultrasonic-assisted chemical extraction].

Science.gov (United States)

Wang, Xin-jie; Huang, Jin-lou; Liu, Zhi-qiang; Yue, Xi

2013-09-01

This research chose five lead-contaminated sites of a lead-acid battery factory to analyze the speciation distribution and concentration of lead. Under the same conditions (0.1 mol x L(-1) EDTA,30 min, 25 degrees C), the removal effect of heavy metal was compared between ultrasonic-assisted chemical extraction (UCE) and conventional chemical extraction ( CCE), and the variation of lead speciation was further explored. The results showed that the lead removal efficiency of UCE was significantly better than CCE. The lead removal efficiency of WS, A, B, C and BZ was 10.06%, 48.29%, 48.69%, 53.28% and 36.26% under CCE. While the removal efficiency of the UCE was 22.42%, 69.31%, 71.00%, 74.49% and 71.58%, with the average efficiency higher by 22%. By comparing the speciation distribution of the two washing methods, it was found that the acid extractable content maintained or decreased after UCE, whereas it showed an increasing trend after CCE. The reduction effect of the reducible was as high as 98% by UCE. UCE also showed a more efficient reduction effect of the organic matter-sulfite bounded form and the residual form. Hence, it is feasible to improve the washing efficiency of heavy metal contained in soil by conducting the cleaning process with the help of ultrasonic wave, which is a simple and fast mean to remove lead from contaminated sites.

Laser-assisted lead extraction: the European experience.

Science.gov (United States)

Kennergren, C; Bucknall, C A; Butter, C; Charles, R; Fuhrer, J; Grosfeld, M; Tavernier, R; Morgado, T B; Mortensen, P; Paul, V; Richter, P; Schwartz, T; Wellens, F

2007-08-01

The aim of this study is to investigate the safety and effectiveness of Excimer laser-assisted lead extraction in Europe. The final European multi-centre study experience is presented. The Excimer is a cool cutting laser (50 degrees C) with a wavelength of 308 nm. The energy is emitted from the tip of a flexible sheath and is absorbed by proteins and lipids, 64% of the energy is absorbed at a tissue depth of 0.06 mm. The sheath is positioned over the lead, and the fibrosis surrounding the lead is vaporized while advancing the sheath without damaging other leads. From August 1996 to March 2001, 383 leads (170 atrial, 213 ventricular) in 292 patients (mean age 61.6 years, range 13-96) were extracted at 14 European centres. Mean implantation time was 74 months (3-358). Most frequent indications were pocket infection (26%), non-functional leads (21%), patient morbidity (21%), septicaemia or endocarditis (14%), erosion (5%), and lead interference (8%). Median extraction time was 15 min (1-300). Complete extraction was achieved in 90.9% of the leads and partial extraction in 3.4%. Extraction failed in 5.7% of the leads. Major complications = perforations caused 10/22 (3.4/5.7%) of the failures. Most partially extracted patients were considered clinically successful, as only minor lead parts without clinical significance were left. Femoral non-laser technique was used to remove 8/12 of the non-complication failures. The total complication rate, including five minor complications (1.7%), was 5.1%. No in-hospital mortality occurred. Pacing and implantable cardioverter-defibrillator leads can safely, effectively, and predictably be extracted. Open-heart extractions can be limited to special cases. The results indicate that the traditional policy of abandoning redundant leads, instead of removing them, may be obsolete in many patients.

Effect of halide impregnation on elemental mercury removal of activated carbons

Energy Technology Data Exchange (ETDEWEB)

Yim, Yoon Ji; Park, Soo Jin [Dept. of Chemistry, Inha University, Incheon (Korea, Republic of)

2017-02-15

Activated carbons (ACs) were impregnated with potassium halides (KX) to enhance the removal efficiency of elemental mercury (Hg{sup 0}). In this work, the impregnation effect of potassium bromide (KBr) and potassium iodine (KI) were investigated. The surface properties of KX-ACs were determined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The pore structures and total pore volumes of the KX-ACs were analyzed using the N{sub 2} /77 K adsorption isotherms. The Hg{sup 0} removal efficiency of KBr-ACs and KI-ACs was studied under simulated flue gas conditions. The effects of KI and KBr loading, adsorption temperature, and flue gas components on Hg{sup 0} removal efficiency were also investigated. The results showed that the Hg{sup 0} removal efficiency of the ACs was significantly enhanced by KI or KBr impregnation, and KI-ACs showed higher Hg{sup 0} removal efficiency than KBr-ACs under the same conditions. An increase in KI or KBr loading and higher adsorption temperatures improved the Hg{sup 0} removal efficiency, indicating that chemisorption occurred due to the reaction between X− and Hg{sup 0}. The lower extent of Hg{sup 0} removal exhibited by the KBr-ACs than by the KI-ACs was due to the difficulty of Br{sub 2} formation on the surfaces.

Structural evolution of chitosan–palygorskite composites and removal of aqueous lead by composite beads

International Nuclear Information System (INIS)

Rusmin, Ruhaida; Sarkar, Binoy; Liu, Yanju; McClure, Stuart; Naidu, Ravi

2015-01-01

Graphical abstract: - Highlights: • Facile preparation of chitosan–palygorskite composite beads demonstrated. • Components’ mass ratio impacted structural characteristics of composites. • Mechanism of composite formation and structure of composite beads proposed. • Composite beads adsorbed significantly greater amount of Pb than pristine materials. • In-depth investigation done on Pb adsorption mechanisms. - Abstract: This paper investigates the structural evolution of chitosan–palygorskite (CP) composites in relation to variable mass ratios of their individual components. The composite beads’ performance in lead (Pb) adsorption from aqueous solution was also examined. The composite beads were prepared through direct dispersion of chitosan and palygorskite at 1:1, 1:2 and 2:1 mass ratios (CP1, CP2 and C2P, respectively). Analyses by Fourier transform Infrared (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) surface area, X-ray diffraction (XRD) and scanning electron microscopy (SEM) confirmed the dependence of the composites’ structural characteristics on their composition mass ratio. The chitosan–palygorskite composite beads exhibited a better Pb adsorption performance than the pristine materials (201.5, 154.5, 147.1, 27.7 and 9.3 mg g"−"1 for CP1, C2P, CP2, chitosan and palygorskite, respectively). Adsorption of Pb by CP1 and CP2 followed Freundlich isothermal model, while C2P fitted to Langmuir model. Kinetic studies showed that adsorption by all the composites fitted to the pseudo-second order model with pore diffusion also acting as a major rate governing step. The surface properties and specific interaction between chitosan and palygorskite in the composites were the most critical factors that influenced their capabilities in removing toxic metals from water.

Structural evolution of chitosan–palygorskite composites and removal of aqueous lead by composite beads

Energy Technology Data Exchange (ETDEWEB)

Rusmin, Ruhaida, E-mail: ruhaida.rusmin@mymail.unisa.edu.au [CERAR – Centre for Environmental Risk Assessment and Remediation, Building X, University of South Australia, Mawson Lakes, SA 5095 (Australia); Faculty of Applied Sciences, Universiti Teknologi MARA Negeri Sembilan, Kuala Pilah 72000 (Malaysia); Sarkar, Binoy, E-mail: binoy.sarkar@unisa.edu.au [CERAR – Centre for Environmental Risk Assessment and Remediation, Building X, University of South Australia, Mawson Lakes, SA 5095 (Australia); CRC CARE – Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, P.O. Box 486, Salisbury, SA 5106 (Australia); Liu, Yanju [CERAR – Centre for Environmental Risk Assessment and Remediation, Building X, University of South Australia, Mawson Lakes, SA 5095 (Australia); CRC CARE – Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, P.O. Box 486, Salisbury, SA 5106 (Australia); McClure, Stuart [CERAR – Centre for Environmental Risk Assessment and Remediation, Building X, University of South Australia, Mawson Lakes, SA 5095 (Australia); Naidu, Ravi, E-mail: Ravi.Naidu@newcastle.edu.au [CERAR – Centre for Environmental Risk Assessment and Remediation, Building X, University of South Australia, Mawson Lakes, SA 5095 (Australia); CRC CARE – Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, P.O. Box 486, Salisbury, SA 5106 (Australia)

2015-10-30

Graphical abstract: - Highlights: • Facile preparation of chitosan–palygorskite composite beads demonstrated. • Components’ mass ratio impacted structural characteristics of composites. • Mechanism of composite formation and structure of composite beads proposed. • Composite beads adsorbed significantly greater amount of Pb than pristine materials. • In-depth investigation done on Pb adsorption mechanisms. - Abstract: This paper investigates the structural evolution of chitosan–palygorskite (CP) composites in relation to variable mass ratios of their individual components. The composite beads’ performance in lead (Pb) adsorption from aqueous solution was also examined. The composite beads were prepared through direct dispersion of chitosan and palygorskite at 1:1, 1:2 and 2:1 mass ratios (CP1, CP2 and C2P, respectively). Analyses by Fourier transform Infrared (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) surface area, X-ray diffraction (XRD) and scanning electron microscopy (SEM) confirmed the dependence of the composites’ structural characteristics on their composition mass ratio. The chitosan–palygorskite composite beads exhibited a better Pb adsorption performance than the pristine materials (201.5, 154.5, 147.1, 27.7 and 9.3 mg g{sup −1} for CP1, C2P, CP2, chitosan and palygorskite, respectively). Adsorption of Pb by CP1 and CP2 followed Freundlich isothermal model, while C2P fitted to Langmuir model. Kinetic studies showed that adsorption by all the composites fitted to the pseudo-second order model with pore diffusion also acting as a major rate governing step. The surface properties and specific interaction between chitosan and palygorskite in the composites were the most critical factors that influenced their capabilities in removing toxic metals from water.

Is Central Europe Safe from Environmental Lead Intoxications? A Case Series.

Science.gov (United States)

Pelclová, Daniela; Šťastná, Jana; Vlčková, Štěpánka; Vlček, Kamil; Urban, Michal; Laštovková, Andrea; Doležel, Zdeněk

2016-06-01

Preventive measures in Central Europe were successful in suppressing both occupational and environmental lead exposure so that they did not constitute a severe public health problem. However, rare lead intoxications still appear. We report on lead intoxication in four family members where the source was removed lead ceiling paint. The symptoms of the lead intoxication started several weeks after removal and the inhalational exposure to the minimum dust residues lasted for more than three months before the poisoning was diagnosed. Father developed anaemia and saturnine colics. He and his two daughters received antidotal treatment which had to be repeated in the children. Finally, all recovered completely.Lead intoxication may be easily overlooked due to the unspecific symptoms. It is necessary to think of this rare poisoning which may be caused by old paints, historical ceramics and lead shots, in addition to commercial products imported from abroad. Copyright© by the National Institute of Public Health, Prague 2015.

Lead tolerance in plants: strategies for phytoremediation.

Science.gov (United States)

Gupta, D K; Huang, H G; Corpas, F J

2013-04-01

Lead (Pb) is naturally occurring element whose distribution in the environment occurs because of its extensive use in paints, petrol, explosives, sludge, and industrial wastes. In plants, Pb uptake and translocation occurs, causing toxic effects resulting in decrease of biomass production. Commonly plants may prevent the toxic effect of heavy metals by induction of various celular mechanisms such as adsorption to the cell wall, compartmentation in vacuoles, enhancement of the active efflux, or induction of higher levels of metal chelates like a protein complex (metallothioneins and phytochelatins), organic (citrates), and inorganic (sulphides) complexes. Phyotochelains (PC) are synthesized from glutathione (GSH) and such synthesis is due to transpeptidation of γ-glutamyl cysteinyl dipeptides from GSH by the action of a constitutively present enzyme, PC synthase. Phytochelatin binds to Pb ions leading to sequestration of Pb ions in plants and thus serves as an important component of the detoxification mechanism in plants. At cellular level, Pb induces accumulation of reactive oxygen species (ROS), as a result of imbalanced ROS production and ROS scavenging processes by imposing oxidative stress. ROS include superoxide radical (O2(.-)), hydrogen peroxide (H2O2) and hydroxyl radical ((·)OH), which are necessary for the correct functioning of plants; however, in excess they caused damage to biomolecules, such as membrane lipids, proteins, and nucleic acids among others. To limit the detrimental impact of Pb, efficient strategies like phytoremediation are required. In this review, it will discuss recent advancement and potential application of plants for lead removal from the environment.

Removal of methadone by extended dialysis using a high cut-off dialyzer: implications for the treatment of overdose and for pain management in patients undergoing light chain removal.

Science.gov (United States)

Arelin, Viktor; Schmidt, Julius J; Kayser, Nathalie; Kühn-Velten, W Nikolaus; Suhling, Hendrik; Eden, Gabriele; Kielstein, Jan T

2016-06-01

The synthetic opioid methadone hydrochloride has a low molecular weight of 346 D, a high volume of distribution (4 - 7 L/kg), and is lipophilic. It is used as an analgesic and for the maintenance treatment of opiate dependence. In drug addicts, methadone is frequently involved in mixed intoxications that can lead to death. Here we present the case of a drug addict in whom a high cut-off dialysis membrane together with extended dialysis was used in the setting of suspected overdose and acute kidney injury. Although the observed dialyzer plasma clearance (31.5 mL/min) and reduction ratio (38%) were higher than previously reported for standard hemodialysis, the total amount of methadone in the spent dialysate after 1 extended dialysis session was quite low. Hence, even extended dialysis with a high cut-off membrane does not seem to offer a clinically relevant benefit in the setting of overdose for enhanced methadone removal. On the other hand, in patients undergoing high cut-off dialysis for the removal of light chains, methadone could still be used as an analgesic without an additional dose after high cut-off hemodialysis.

Contaminant removal performances on domestic sewage using modified anoxic/anaerobic/oxic process and micro-electrolysis.

Science.gov (United States)

Zhou, Jun; Gao, Jingqing; Liu, Yifan; Xiao, Shuai; Zhang, Ruiqin; Zhang, Zhenya

2013-01-01

The objective of this study was to enhance removal of chemical oxygen demand (COD), total nitrogen (TN) and total phosphorus (TP) from domestic sewage in a sequencing batch reactor with added new materials. A modified anoxic/anaerobic/oxic (MAAO) process, integrating a micro-electrolysis (ME) bed in an anoxic tank, and complex biological media (CBM) in anoxic, anaerobic and oxic tanks to treat domestic sewage, and their performances were investigated. The MAAO system was operated at controlled hydraulic retention time (HRT) of 8 h and mixed liquor recirculation (MLR) at 75%. The results showed that the MAAO system could effectively remove COD, TN and TP with average rates of 93%, 80% and 94%, respectively, in March, and 94%, 76% and 91%, respectively, in August. In this system, TP was primarily removed from the anoxic tank regardless of the operational conditions; removal contribution ratios to TP of the anoxic tank reached 56% both in March and August, indicating that the ME bed can effectively enhance phosphorus removal. TN was primarily removed from the anoxic and anaerobic tanks; removal contribution ratios to TN of anoxic and anaerobic tanks reached 36-38% and 37-38%, respectively. The oxic tank had the highest share of COD removal (56% both in March and August) in the removal of phosphorus. The outflow concentrations of COD, TN and TP were 3-46, 7-14 and 0.3-0.5 mg/L, respectively, in March, and 26-49, 9-15 and 0.04-0.1 mg/L, respectively, in August. COD and TN removal performances indicated that the innovative materials of the ME bed and CBM can effectively enhance COD and TN removal.

Arsenic removal by magnetic nanocrystalline barium hexaferrite

Energy Technology Data Exchange (ETDEWEB)

Patel, Hasmukh A.; Byun, Jeehye; Yavuz, Cafer T., E-mail: yavuz@kaist.ac.kr [Graduate School of EEWS, Korea Advanced Institute of Science and Technology (KAIST) (Korea, Republic of)

2012-07-15

Nanoscale magnetite (Fe{sub 3}O{sub 4}) (<15 nm) is known to remove arsenic efficiently but is very difficult to separate or require high magnetic fields to separate out from the waste water after treatment. Anisotropic hexagonal ferrite (BaFe{sub 12}O{sub 19}, BHF) is a well-known permanent magnet (i.e., fridge magnets) and attractive due to its low cost in making large quantities. BHF offers a viable alternative to magnetite nanocrystals for arsenic removal since it features surfaces similar to iron oxides but with much enhanced magnetism. Herein, we employ BHF nanocrystalline materials for the first time in arsenic removal from wastewater. Our results show better (75 %) arsenic removal than magnetite of the similar sizes. The BHF nanoparticles, 6.06 {+-} 0.52 nm synthesized by thermolysis method at 320 Degree-Sign C do not show hexagonal phase, however, subsequent annealing at 750 Degree-Sign C produced pure hexagonal BHF in >200 nm assemblies. By using BHF, we demonstrate that nanoparticle removal is more efficient and fixed bed type cartridge applications are more possible.

Guidelines for removing permanent makeup

Directory of Open Access Journals (Sweden)

C.Bettina Rümmelein

2016-09-01

Full Text Available Permanent makeup (PMU is a frequently implemented cosmetic procedure performed by beauticians. From a technical point, PMU is considered a facial tattoo. Failed procedures or a change of mind can lead to the desire for removal. The purpose of this retrospective evaluation of patients who came to the clinic with the desire to remove PMU between 2011 and 2015 was to explore the problems, side effects, and results in order to define treatment guidelines for other doctors. We evaluated 87 individual cases in total. In treatable cases, i.e. 52 out of the 87 cases, laser treatments were performed using a nanosecond Q-switched neodymium-doped yttrium aluminium garnet (Nd:YAG laser. It takes between 1-12 treatments to remove the PMU. In three cases, the colour of the PMU could not be removed by laser and remained after the treatment. In two cases, laser treatment had to be terminated due to colour changes towards the green-blue spectrum. Before PMU removal, laser test shots are urgently recommended as unforeseeable colour changes can cause severe aesthetically unpleasant results. Covered up PMU (skin colour is particularly susceptible to changes in colour. Heat-induced shrinking of the eye area can cause an ectropium. Surgical solutions also have to be taken into consideration. The use of proper eye protection with intraocular eye shields is mandatory. This article is an attempt to set up some guidelines for the treatment of PMU removal.

Enhanced nitrogen removal in single-chamber microbial fuel cells with increased gas diffusion areas

KAUST Repository

Yan, Hengjing; Regan, John M.

2012-01-01

significantly increased the ammonia and COD removal rates (by up to 115% and 39%), ammonia removal efficiency (by up to 134%), the cell voltage and cathode potentials, and the power densities (by a factor of approximately 2). When the COD/N ratio was lowered

Removal and transformation of effluent organic matter (EfOM) in biotreated textile wastewater by GAC/O3 pre-oxidation and enhanced coagulation.

Science.gov (United States)

Qian, Feiyue; Sun, Xianbo; Liu, Yongdi; Xu, Hongyong

2013-01-01

GAC/O3 (ozonation in the presence of granular activated carbon) combined with enhanced coagulation was employed to process biotreated textile wastewater for possible reuse. The doses of ozone, GAC and coagulant were the variables studied for optimization. The effects of different treatment processes on effluent organic matter (EfOM) characteristics, including biodegradability, hydrophobic and hydrophilic nature, and apparent molecular weight (AMW) distribution were also investigated. Compared with ozonation, GAC/O3 not only presented a higher pre-oxidation efficiency, but also improved the treatability of hydrophobic and high molecular weight compounds by enhanced coagulation. After treatment by GAC/O3 pre-oxidation (0.6 mg O3 x mg(-1) COD and 20 g x L(-1) GAC) and enhanced coagulation (25 mg x L(-1) Al3+ at pH 5.5), the removal efficiencies of chemical oxygen demand (COD), dissolved organic carbon (DOC) and colour were higher than those for coagulation alone by 17.3%, 12.0% and 25.6%, respectively. Residual organic matter consisted mainly of hydrophobic acids and hydrophilic compounds of AMW wastewater.

2D BiOCl/Bi12O17Cl2 nanojunction: Enhanced visible light photocatalytic NO removal and in situ DRIFTS investigation

Science.gov (United States)

Zhang, Wendong; Dong, Xin'an; Jia, Bin; Zhong, Junbo; Sun, Yanjuan; Dong, Fan

2018-02-01

Novel two-dimensional (2D) BiOCl/Bi12O17Cl2 nanojunctions were fabricated by a facile one-pot in situ method at room temperature. The as-prepared samples were analyzed by XRD, SEM, TEM, HRTEM, UV-vis DRS, PL, ESR and BET-BJH measurement in detail. The photocatalytic performance of the samples was evaluated by removal of NO at ppb level under visible-light illumination. The result reveals that the BiOCl/Bi12O17Cl2 nanojunctions manifests conspicuously enhanced photocatalytic efficiency for NO removal. The facilitated performance can be ascribed to the well-matched band structure and relatively high specific surface area. In addition, the in situ diffuse reflectance infrared Fourier transform spectroscopy was applied to investigate the adsorption and photocatalytic NO oxidation processes. The reaction mechanism of photocatalytic NO oxidation was proposed based on the observed intermediates. The present work could pave a way to synthesize novel visible light photocatalysts at room temperature for environmental application.

Laboratory investigations of stormwater remediation via slag: Effects of metals on phosphorus removal

International Nuclear Information System (INIS)

Okochi, Nnaemeka C.; McMartin, Dena W.

2011-01-01

The use of electric arc furnace (EAF) slag for the removal of phosphorus (P) from various simulated stormwater blends was investigated in the laboratory. The form of P measured was the inorganic orthophosphate (PO 4 -P). The stormwater solutions used in this preliminary study were synthesized as blends of P and typical concentrations of some of the most common and abundant metals in stormwater (e.g. cadmium, copper, lead and zinc), and contacted with EAF slag to determine P removal efficiency and sorptive competition. Results showed that the presence of cadmium, lead and zinc had minimal effect on the removal process; copper was a significant inhibitor of P uptake by the EAF slag media. P removal was greatest in the metal-free and multi-metal stormwater solutions.

Crocodile bones as archives of pollution exposure: lead contamination in Kakadu National Park, and what's in Sweetheart's Osteoderms?

International Nuclear Information System (INIS)

Jeffree, R.A.; Markich, S.J.; Hammerton, K.M.; Russell, R.

2002-01-01

Experimental findings made it then possible to evaluate the hypothesis that the estuarine crocodile osteodermal laminations would record enhanced blood lead concentrations resulting from the ingestion of lead shot. At about 140 days following lead shot ingestion, two osteoderms were removed from each exposed and control animal. SIMS analysis of Pb-208 and Ca-42 signal intensities was then performed on sections that were prepared and analysed using similar methods previously used on field-collected specimens (Twining et al., 1999). These initial findings are consistent with the hypothesis that incremental laminations of the osteoderm will archive a lead signal that responds to enhanced levels of lead in the animal's blood during its life. SEM analysis identified the laminated structure of the osteoderm, however microprobe analysis did not detect appreciable amounts of even Ca and P, although the organic matrix was obviously present. It is proposed that this anomalous result is due to the preparatory tanning of the skin, in acid solution, that could be expected to leach elements from the organic matrix. An analogy is drawn with the decalcified skeletons in the bodies of the Druid sacrifices due their deposition in acid swamp waters in the UK. The challenge is now to sample osteoderms from large crocodiles in the Finniss River, preferably in close proximity to the Rum Jungle mine site, where any archived pollution signal would be more intense, and then repeat this analytical investigation of the osteodermal history of contaminant loadings

A Critical Assessment of the Microorganisms Proposed to be Important to Enhanced Biological Phosphorus Removal in Full-Scale Wastewater Treatment Systems

Directory of Open Access Journals (Sweden)

Per H. Nielsen

2017-04-01

Full Text Available Understanding the microbiology of phosphorus (P removal is considered essential to knowledge-based optimization of enhanced biological P removal (EBPR systems. Biological P removal is achieved in these systems by promoting the growth of organisms collectively known as the polyphosphate accumulating organisms (PAOs. Also considered important to EBPR are the glycogen accumulating organisms (GAOs, which are theorized to compete with the PAOs for resources at the expense of P removal efficiency. Numerous studies have sought to identify the PAOs and their GAOs competitors, with several candidates proposed for each over the last few decades. The current study collectively assessed the abundance and diversity of all proposed PAOs and GAOs in 18 Danish full-scale wastewater treatment plants with well-working biological nutrient removal over a period of 9 years using 16S rRNA gene amplicon sequencing. The microbial community structure in all plants was relatively stable over time. Evidence for the role of the proposed PAOs and GAOs in EBPR varies and is critically assessed, in light of their calculated amplicon abundances, to indicate which of these are important in full-scale systems. Bacteria from the genus Tetrasphaera were the most abundant of the PAOs. The “Candidatus Accumulibacter” PAOs were in much lower abundance and appear to be biased by the amplicon-based method applied. The genera Dechloromonas, Microlunatus, and Tessaracoccus were identified as abundant putative PAO that require further research attention. Interestingly, the actinobacterial Micropruina and sbr-gs28 phylotypes were among the most abundant of the putative GAOs. Members of the genera Defluviicoccus, Propionivibrio, the family Competibacteraceae, and the spb280 group were also relatively abundant in some plants. Despite observed high abundances of GAOs (periodically exceeding 20% of the amplicon reads, P removal performance was maintained, indicating that these organisms

Column study of enhanced Cr(VI) removal and longevity by coupled abiotic and biotic processes using Fe0 and mixed anaerobic culture.

Science.gov (United States)

Zhong, Jiawei; Yin, Weizhao; Li, Yongtao; Li, Ping; Wu, Jinhua; Jiang, Gangbiao; Gu, Jingjing; Liang, Hao

2017-10-01

In this study, Fe 0 and mixed anaerobic culture were integrated in one column to investigate the coupled abiotic and biotic effects on hexa-valent chromium (Cr(VI)) removal and column longevity with an abiotic Fe 0 column in the control experiments. According to the breakthrough study, a slower Cr(VI) breakthrough rate of 0.19 cm/PV was observed in the biotic Fe 0 column whereas the value in the abiotic Fe 0 column was 0.30 cm/PV, resulting in 64% longer life-span and 62% higher Cr(VI) removal capacity in the biotic Fe 0 column than the abiotic one. The solid phase characterization by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and X-ray diffraction (XRD) confirmed that this enhancement was attributed to the higher consumption of iron and greater production of diverse reactive minerals (e.g., green rust, magnetite and lepidocrocite) induced by the synergistic interaction of Fe 0 and anaerobic culture, providing more reactive sites for Cr(VI) adsorption, reduction and co-precipitation. Furthermore, the decreasing breakthrough rates and growing iron corrosion along the biotic Fe 0 column demonstrated an inhomogeneous distribution of reactive zones in the column and its latter 3/5 section was considered to be the most reactive area for Cr(VI) removal. These results indicate that the inoculation of microorganisms in Fe 0 -based permeable reactive barriers will enable this technology a higher removal capacity and longer life-span for the remediation of Cr(VI)-contaminated groundwater. Copyright © 2017 Elsevier Ltd. All rights reserved.

Functionally relevant microorganisms to enhanced biological phosphorus removal performance at full-scale wastewater treatment plants in the United States.

Science.gov (United States)

Gu, April Z; Saunders, A; Neethling, J B; Stensel, H D; Blackall, L L

2008-08-01

The abundance and relevance ofAccumulibacter phosphatis (presumed to be polyphosphate-accumulating organisms [PAOs]), Competibacter phosphatis (presumed to be glycogen-accumulating organisms [GAOs]), and tetrad-forming organisms (TFOs) to phosphorus removal performance at six full-scale enhanced biological phosphorus removal (EBPR) wastewater treatment plants were investigated. Coexistence of various levels of candidate PAOs and GAOs were found at these facilities. Accumulibacter were found to be 5 to 20% of the total bacterial population, and Competibacter were 0 to 20% of the total bacteria population. The TFO abundance varied from nondetectable to dominant. Anaerobic phosphorus (P) release to acetate uptake ratios (P(rel)/HAc(up)) obtained from bench tests were correlated positively with the abundance ratio of Accumulibacter/(Competibacter +TFOs) and negatively with the abundance of (Competibacter +TFOs) for all plants except one, suggesting the relevance of these candidate organisms to EBPR processes. However, effluent phosphorus concentration, amount of phosphorus removed, and process stability in an EBPR system were not directly related to high PAO abundance or mutually exclusive with a high GAO fraction. The plant that had the lowest average effluent phosphorus and highest stability rating had the lowest P(rel)/HAc(up) and the most TFOs. Evaluation of full-scale EBPR performance data indicated that low effluent phosphorus concentration and high process stability are positively correlated with the influent readily biodegradable chemical oxygen demand-to-phosphorus ratio. A system-level carbon-distribution-based conceptual model is proposed for capturing the dynamic competition between PAOs and GAOs and their effect on an EBPR process, and the results from this study seem to support the model hypothesis.

Tuning the electrocaloric enhancement near the morphotropic phase boundary in lead-free ceramics

Science.gov (United States)

Le Goupil, Florian; McKinnon, Ruth; Koval, Vladimir; Viola, Giuseppe; Dunn, Steve; Berenov, Andrey; Yan, Haixue; Alford, Neil Mcn.

2016-06-01

The need for more energy-efficient and environmentally-friendly alternatives in the refrigeration industry to meet global emission targets has driven efforts towards materials with a potential for solid state cooling. Adiabatic depolarisation cooling, based on the electrocaloric effect (ECE), is a significant contender for efficient new solid state refrigeration techniques. Some of the highest ECE performances reported are found in compounds close to the morphotropic phase boundary (MPB). This relationship between performance and the MPB makes the ability to tune the position of the MPB an important challenge in electrocaloric research. Here, we report direct ECE measurements performed on MPB tuned NBT-06BT bulk ceramics with a combination of A-site substitutions. We successfully shift the MPB of these lead-free ceramics closer to room temperature, as required for solid state refrigeration, without loss of the criticality of the system and the associated ECE enhancement.

Decontaminating lead bricks and shielding

International Nuclear Information System (INIS)

Lussiez, G.W.

1993-01-01

Lead used for shielding is often surface contaminated with radionuclides and is therefore a Resource Conservation and Recovery Act (RCRA) D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Lab. decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 100 metric tons and likely to grow substantially because of planned decommissioning operations. This lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for decontaminating lead is removing the thin superficial layer of contamination with an abrasive medium under pressure. For lead, a mixture of alumina with water and air at about 280 kPa (40 psig) rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a sealed-off area. The slurry of abrasive and particles of lead falls through a floor grating and is collected in a pump. A pump sends the slurry mixture back to the spray gun, creating a continuous process

Effect of wastewater colloids on membrane removal of antibiotic resistance genes.

Science.gov (United States)

Breazeal, Maria V Riquelme; Novak, John T; Vikesland, Peter J; Pruden, Amy

2013-01-01

Recent studies have demonstrated that wastewater treatment plants (WWTPs) significantly alter the magnitude and distribution of antibiotic resistance genes (ARGs) in receiving environments, indicating that wastewater treatment represents an important node for limiting ARG dissemination. This study examined the potential for membrane treatment of microconstituent ARGs and the effect of native wastewater colloids on the extent of their removal. Plasmids containing vanA (vancomycin) and bla(TEM) (β-lactam) ARGs were spiked into three representative WWTP effluents versus a control buffer and tracked by quantitative polymerase chain reaction through a cascade of microfiltration and ultrafiltration steps ranging from 0.45 μm to 1 kDa. Significant removal of ARGs was achieved by membranes of 100 kDa and smaller, and presence of wastewater colloids resulted in enhanced removal by 10 kDa and 1 kDa membranes. ARG removal was observed to correlate significantly with the corresponding protein, polysaccharide, and total organic carbon colloidal fractions. Alumina membranes removed ARGs to a greater extent than polyvinylidene fluoride membranes of the same pore size (0.1 μm), but only in the presence of wastewater material. Control studies confirmed that membrane treatment was the primary mechanism of ARG removal, versus other potential sources of loss. This study suggests that advanced membrane treatment technology is promising for managing public health risks of ARGs in wastewater effluents and that removal may even be enhanced by colloids in real-world wastewaters. Copyright © 2012 Elsevier Ltd. All rights reserved.

DELAMINATION AND XRF ANALYSIS OF NIST LEAD IN PAINT FILM STANDARDS

Science.gov (United States)

The objectives of this protocol were to remove the laminate coating from lead paint film standards acquired from NIST by means of surface heating. The average XRF value did not change after removal of the polymer coating suggesting that this protocol is satisfactory for renderin...

Electrodialytic Removal of Heavy Metals from Different Solid Waste Products

DEFF Research Database (Denmark)

Ottosen, Lisbeth M.; Christensen, Iben Vernegren; Pedersen, Anne Juul

2003-01-01

in a 7-day experiment in which oxalic acid was used as enhancement solution. From the straw ash, 66% of the Cd was removed, but 64% of the fly ash dry mass dissolved during the treatment. In this actual experiment, no enhancement solution was used but that will be necessary to avoid dissolution...

Phase separation of cesium from lead borosilicate glass by heat treatment under a reducing atmosphere

Energy Technology Data Exchange (ETDEWEB)

Xu, Zhanglian; Okada, Takashi, E-mail: t-okada@u-fukui.ac.jp; Nishimura, Fumihiro; Yonezawa, Susumu

2016-11-05

Highlights: • Cesium was phase separated from lead borosilicate glass under a reductive atmosphere. • The phase separation occurred on the glass surface that was in contact with the gas. • The leachability of cesium was enhanced by the phase separation. • The degree of such enhancement varied depending on the heat treatment conditions. - Abstract: A phase-separation technique for removing sodium from glass using a heat-treatment method under a reducing atmosphere was previously developed for sodium recovery from waste glass. In this study, this technique was applied to cesium-containing lead borosilicate glass to concentrate the cesium in phase-separated sodium-rich materials for efficient cesium extraction. The theoretical phase-separation temperature of the sodium-rich phase was simulated by thermodynamic equilibrium calculations and was predicted to occur below 700 °C for lead borosilicate glass. Experimentally, a simulated lead borosilicate glass was melted at 1000 °C and subsequently annealed below 700 °C under a CO-containing reducing atmosphere. The phase separation of cesium was found to occur with sodium enrichment on the glass surface that was in contact with the gas phase, promoting cesium extraction from the treated glass using water. The cesium extraction efficiency was affected by the surface area of the treated glass that was in contact with water, and under the examined conditions, the cesium extraction efficiency was up to 66%. Phase separation using reductive heat treatment, combined with a water leaching technique, is suggested to be effective for extracting cesium incorporated in borosilicate glass waste.

Decontaminating lead bricks and shielding

International Nuclear Information System (INIS)

Lussiez, G.

1994-01-01

Lead used for shielding is often surface contaminated with radioisotopes and is therefore a RCRA D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Laboratory decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 50 tons and likely to grow substantially of planned decommissioning operations. Thus lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for contaminated lead is removing the superficial layer of contamination with an abrasive medium under pressure. For lead, a mixture of alumina with water and air at about 40 psig rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a scaled-off area. The slurry of abrasive and particles of lead falls through a floor and is collected in a sump. A pump sends the slurry mixture back to the spray gun, creating a continuous process. The process generates small volumes of lead slurry that can be solidified and, because it passes the TCLP, is not a mixed waste. The decontaminated lead can be released for recycling

Treatment techniques for removing natural radionuclides from drinking water. Final report of the TENAWA project

International Nuclear Information System (INIS)

Annanmaeki, M.; Turtiainen, T.

2000-01-01

TENAWA project (Treatment Techniques for Removing Natural Radionuclides from Drinking Water) was carried out on a cost-shared basic with the European Commission (CEC) under the supervision of Directorate-General XII, Radiation Protection Unit. TENAWA project was started because in several European countries ground water supplies may contain high amounts of natural radionuclides. During the project both laboratory and field research was performed in order to test the applicability of different equipment and techniques for removing natural radionuclides from drinking water. The measurable objectives of the project were: to give recommendations on the most suitable methods for removing radon ( 222 Rn), uranium ( 238,234 U), radium ( 226 , 228 Ra), lead ( 210 Pb) and polonium ( 210 Po) from drinking water of different qualities (i.e. soft, hard, iron-, manganese- and humus-rich, acidic) to test commercially available equipment for its ability to remove radionuclides; to find new materials, absorbents and membranes effective in the removal of radionuclides and to issue guidelines for the treatment and disposal of radioactive wastes produced in water treatment. Radon could be removed efficiently (>95%) from domestic water supplies by both aeration and granular activated carbon (GAC) filtration. Defects in technical reliability or radon removal efficiency were observed in some aerators. The significant drawback of GAC filtration was the elevated gamma dose rates (up to 120 μSv/h) near the filter and the radioactivity of spent GAC. Aeration was found to be a suitable method for removing radon at waterworks, too. The removal efficiencies at waterworks where the aeration process was designed to remove radon or carbon dioxide were 67-99%. If the aeration process was properly designed, removal efficiencies higher than 95% could be attained. Uranium could best be removed (>95%) with strong basic anion exchange resins and radium by applying strong acidic cation exchange resins