WorldWideScience

Sample records for engineers receive top

  1. Wave Engine Topping Cycle Assessment

    Science.gov (United States)

    Welch, Gerard E.

    1996-01-01

    The performance benefits derived by topping a gas turbine engine with a wave engine are assessed. The wave engine is a wave rotor that produces shaft power by exploiting gas dynamic energy exchange and flow turning. The wave engine is added to the baseline turboshaft engine while keeping high-pressure-turbine inlet conditions, compressor pressure ratio, engine mass flow rate, and cooling flow fractions fixed. Related work has focused on topping with pressure-exchangers (i.e., wave rotors that provide pressure gain with zero net shaft power output); however, more energy can be added to a wave-engine-topped cycle leading to greater engine specific-power-enhancement The energy addition occurs at a lower pressure in the wave-engine-topped cycle; thus the specific-fuel-consumption-enhancement effected by ideal wave engine topping is slightly lower than that effected by ideal pressure-exchanger topping. At a component level, however, flow turning affords the wave engine a degree-of-freedom relative to the pressure-exchanger that enables a more efficient match with the baseline engine. In some cases, therefore, the SFC-enhancement by wave engine topping is greater than that by pressure-exchanger topping. An ideal wave-rotor-characteristic is used to identify key wave engine design parameters and to contrast the wave engine and pressure-exchanger topping approaches. An aerodynamic design procedure is described in which wave engine design-point performance levels are computed using a one-dimensional wave rotor model. Wave engines using various wave cycles are considered including two-port cycles with on-rotor combustion (valved-combustors) and reverse-flow and through-flow four-port cycles with heat addition in conventional burners. A through-flow wave cycle design with symmetric blading is used to assess engine performance benefits. The wave-engine-topped turboshaft engine produces 16% more power than does a pressure-exchanger-topped engine under the specified topping

  2. Hawking receives top US award at White House

    Science.gov (United States)

    Banks, Michael

    2009-09-01

    The Cambridge physicist Stephen Hawking has been awarded the highest US civilian honour - the presidential medal of freedom. At a ceremony at the White House last month, Hawking, together with 15 other recipients, received the 2009 award from President Barack Obama. The medal is given to individuals who make a contribution "to the security or national interests of the US, world peace, cultural or other significant public or private endeavours".

  3. Process engineering applied to receiving waters

    DEFF Research Database (Denmark)

    Harremoës, Poul

    1973-01-01

    Processes in the media, which recieve waste, must be included in the sphere of interest within industry's environmental consciousness. Pollution problems are not very simple and should thus not be dealt with in too simple a fashion. Chemical engineers are very well suited to deal...

  4. Study of a LH2-fueled topping cycle engine for aircraft propulsion

    Science.gov (United States)

    Turney, G. E.; Fishbach, L. H.

    1983-01-01

    An analytical investigation was made of a topping cycle aircraft engine system which uses a cryogenic fuel. This system consists of a main turboshaft engine which is mechanically coupled (by cross-shafting) to a topping loop which augments the shaft power output of the system. The thermodynamic performance of the topping cycle engine was analyzed and compared with that of a reference (conventional-type) turboshaft engine. For the cycle operating conditions selected, the performance of the topping cycle engine in terms of brake specific fuel consumption (bsfc) was determined to be about 12 percent better than that of the reference turboshaft engine. Engine weights were estimated for both the topping cycle engine and the reference turboshaft engine. These estimates were based on a common shaft power output for each engine. Results indicate that the weight of the topping cycle engine is comparable to that of the reference turboshaft engine. Previously announced in STAR as N83-34942

  5. Study of LH2-fueled topping cycle engine for aircraft propulsion

    Science.gov (United States)

    Turney, G. E.; Fishbach, L. H.

    1983-01-01

    An analytical investigation was made of a topping cycle aircraft engine system which uses a cryogenic fuel. This system consists of a main turboshaft engine which is mechanically coupled (by cross-shafting) to a topping loop which augments the shaft power output of the system. The thermodynamic performance of the topping cycle engine was analyzed and compared with that of a reference (conventional-type) turboshaft engine. For the cycle operating conditions selected, the performance of the topping cycle engine in terms of brake specific fuel consumption (bsfc) was determined to be about 12 percent better than that of the reference turboshaft engine. Engine weights were estimated for both the topping cycle engine and the reference turboshaft engine. These estimates were based on a common shaft power output for each engine. Results indicate that the weight of the topping cycle engine is comparable to that of the reference turboshaft engine.

  6. Analysis of a topping-cycle, aircraft, gas-turbine-engine system which uses cryogenic fuel

    Science.gov (United States)

    Turney, G. E.; Fishbach, L. H.

    1984-01-01

    A topping-cycle aircraft engine system which uses a cryogenic fuel was investigated. This system consists of a main turboshaft engine that is mechanically coupled (by cross-shafting) to a topping loop, which augments the shaft power output of the system. The thermodynamic performance of the topping-cycle engine was analyzed and compared with that of a reference (conventional) turboshaft engine. For the cycle operating conditions selected, the performance of the topping-cycle engine in terms of brake specific fuel consumption (bsfc) was determined to be about 12 percent better than that of the reference turboshaft engine. Engine weights were estimated for both the topping-cycle engine and the reference turboshaft engine. These estimates were based on a common shaft power output for each engine. Results indicate that the weight of the topping-cycle engine is comparable with that of the reference turboshaft engine.

  7. Waste Receiving and Processing (WRAP) facility engineering study

    International Nuclear Information System (INIS)

    Christie, M.A.; Cammann, J.W.; McBeath, R.S.; Rode, H.H.

    1985-01-01

    A new Hanford waste management facility, the Waste Receiving and Processing (WRAP) facility (planned to be operational by FY 1994) will receive, inspect, process, and repackage contact-handled transuranic (CH-TRU) contaminated solid wastes. The wastes will be certified according to the waste acceptance criteria for disposal at the Waste Isolation Pilot Plant (WIPP) geologic repository in southeast New Mexico. Three alternatives which could cost effectively be applied to certify Hanford CH-TRU waste to the WIPP Waste Acceptance Criteria (WIPP-WAC) have been examined in this updated engineering study. The alternatives differed primarily in the reference processing systems used to transform nonconforming waste into an acceptable, certified waste form. It is recommended to include the alternative of shredding and immobilizing nonconforming wastes in cement (shred/grout processing) in the WRAP facility. Preliminary capital costs for WRAP in mid-point-of-construction (FY 1991) dollars were estimated at $45 million for new construction and $37 million for modification and installation in an existing Hanford surplus facility (231-Z Building). Operating, shipping, and decommissioning costs in FY 1986 dollars were estimated at $126 million, based on a 23-y WRAP life cycle (1994 to 2017). During this period, the WRAP facility will receive an estimated 38,000 m 3 (1.3 million ft 3 ) of solid CH-TRU waste. The study recommends pilot-scale testing and evaluation of the processing systems planned for WRAP and advises further investigation of the 231-Z Building as an alternative to new facility construction

  8. The Gender and Race-Ethnicity of Faculty in Top Science and Engineering Research Departments

    Science.gov (United States)

    Beutel, Ann M.; Nelson, Donna J.

    This study examines the gender and racial-ethnic composition of faculty in top research departments for science and engineering "S-E - disciplines. There are critical masses of at least 15% women in top research departments in biological sciences, psychology, and social sciences but not in physical sciences and engineering. Blacks and Hispanics together make up only 4.1% of the faculty in our study. Black and Hispanic females are the most poorly represented groups; together, they make up only 1% of the faculty in top S-E research departments. For most S-E disciplines, less than 15% of full professors in top research departments are women or non-Whites.

  9. Instantaneous heat flux flowing into piston top-land surface of D.I. diesel engine; DI diesel kikan no piston top land bu eno shunji netsuryusoku

    Energy Technology Data Exchange (ETDEWEB)

    Taguma, M [Zexel Corp., Tokyo (Japan); Inui, M; Enomoto, Y; Hagihara, Y [Musashi Institute of Technology, Tokyo (Japan); Koyama, T [Mitsubishi Motors Co., Tokyo (Japan)

    1997-10-01

    The thermal loads of the piston top-land surface in D.I. diesel engine during actual operation is not cleared. The authors fixed thin film thermocouples in the top-land center of a standard piston, and measured the instantaneous heat fluxes in that place. As a result, the authors made clear the thermal loads of the piston top-land surface in a cycle, and confirmed presence of the flame inflow to the piston top-land center. In addition, the authors made clear the thermal loads of the piston top-land surface in EGR operation. 4 refs., 8 figs.

  10. Test Operations Procedure (TOP) 05-2-543 Enhanced Flight Termination Receiver (EFTR) Range Certification Testing

    Science.gov (United States)

    2011-07-25

    35 5.10 Signal Strength Telemetry Output ( SSTO ) (Test Number 10) ............ 38 5.11 Operational...All command outputs and monitor outputs shall respond properly. TOP 05-2-543 25 July 2011 38 5.10 Signal Strength Telemetry Output ( SSTO ...Test Number 10). a. Purpose. This test verifies that the signal strength telemetry output ( SSTO ) voltage is monotonic and directly related to the

  11. William Knocke receives 2008 Virginia Outstanding Civil Engineer Award

    OpenAIRE

    Daniilidi, Christina

    2008-01-01

    William R. Knocke, W.C. English Professor and head of the Charles E. Via, Jr. Department of Civil and Environmental Engineering at Virginia Tech, was awarded the 2008 Virginia Outstanding Civil Engineer Award at the Virginia Section of the American Society of Civil Engineers' (ASCE) banquet, held recently in Williamsburg, Va.

  12. Performance Enhancement of One and Two-Shaft Industrial Turboshaft Engines Topped With Wave Rotors

    Science.gov (United States)

    Fatsis, Antonios

    2018-05-01

    Wave rotors are rotating equipment designed to exchange energy between high and low enthalpy fluids by means of unsteady pressure waves. In turbomachinery, they can be used as topping devices to gas turbines aiming to improve performance. The integration of a wave rotor into a ground power unit is far more attractive than into an aeronautical application, since it is not accompanied by any inconvenience concerning the over-weight and extra dimensioning. Two are the most common types of ground industrial gas turbines: The one-shaft and the two-shaft engines. Cycle analysis for both types of gas turbine engines topped with a four-port wave rotor is calculated and their performance is compared to the performance of the baseline engine accordingly. It is concluded that important benefits are obtained in terms of specific work and specific fuel consumption, especially compared to baseline engines with low compressor pressure ratio and low turbine inlet temperature.

  13. Experience with a top-down versus bottom-up nuclear engineering educational paradigm

    International Nuclear Information System (INIS)

    Harms, A.A.

    1991-01-01

    Nuclear engineering courses are generally taught from a top-down pedagogical perspective; i.e., one begins with a body of knowledge drawn from advanced nuclear science, engineering, and experience and from this distills a selected part to match the intellectual capacity of the class. This pedagogical approach has evidently been most effect at the graduate level of instruction as evidenced by the ready entry of masters and doctoral students into the professions. A schematic depiction of this approach is suggested and is extended to the undergraduate level of nuclear engineering education

  14. Manufacturing at Nanoscale: Top-Down, Bottom-up and System Engineering

    International Nuclear Information System (INIS)

    Zhang Xiang; Sun Cheng; Fang, Nicholas

    2004-01-01

    The current nano-technology revolution is facing several major challenges: to manufacture nanodevices below 20 nm, to fabricate three-dimensional complex nano-structures, and to heterogeneously integrate multiple functionalities. To tackle these grand challenges, the Center for Scalable and Integrated NAno-Manufacturing (SINAM), a NSF Nanoscale Science and Engineering Center, set its goal to establish a new manufacturing paradigm that integrates an array of new nano-manufacturing technologies, including the plasmonic imaging lithography and ultramolding imprint lithography aiming toward critical resolution of 1-10 nm and the hybrid top-down and bottom-up technologies to achieve massively parallel integration of heterogeneous nanoscale components into higher-order structures and devices. Furthermore, SINAM will develop system engineering strategies to scale-up the nano-manufacturing technologies. SINAMs integrated research and education platform will shed light to a broad range of potential applications in computing, telecommunication, photonics, biotechnology, health care, and national security

  15. Jacobs Engineering Group Inc. receives architectural and engineering design contract from Stanford Linear Accelerator Centre

    CERN Multimedia

    2004-01-01

    "Jacobs Engineering Group Inc. announced that a subsidiary company won a contract from Stanford Linear Accelerator Center (SLAC), to provide architectural and engineering design services for the Linac Coherent Light Source (LCLS) conventional facilities" (1/2 page)

  16. Engineering satellite-based navigation and timing global navigation satellite systems, signals, and receivers

    CERN Document Server

    Betz, J

    2016-01-01

    This book describes the design and performance analysis of satnav systems, signals, and receivers. It also provides succinct descriptions and comparisons of all the world’s satnav systems. Its comprehensive and logical structure addresses all satnav signals and systems in operation and being developed. Engineering Satellite-Based Navigation and Timing: Global Navigation Satellite Systems, Signals, and Receivers provides the technical foundation for designing and analyzing satnav signals, systems, and receivers. Its contents and structure address all satnav systems and signals: legacy, modernized, and new. It combines qualitative information with detailed techniques and analyses, providing a comprehensive set of insights and engineering tools for this complex multidisciplinary field. Part I describes system and signal engineering including orbital mechanics and constellation design, signal design principles and underlying considerations, link budgets, qua tifying receiver performance in interference, and e...

  17. The all new BMW top diesel engines; Die neuen Diesel Spitzenmotorisierungen von BMW

    Energy Technology Data Exchange (ETDEWEB)

    Ardey, N.; Wichtl, R.; Steinmayr, T.; Kaufmann, M.; Hiemesch, D.; Stuetz, W. [BMW Motoren GmbH, Steyr (Austria)

    2012-11-01

    series standard with an NOx storage catalyst. The new BMW 6-cylinder TwinPower Turbo diesel engine achieves a rated power of 280 kW and a maximum torque of 740 Nm. With a specific power output of 93.6 kW per litre cylinder capacity, it assumes the top position among series diesel engines. Comprehensive friction measures mean that the friction level of existing BMW 6-cylinder diesel drivetrains is achieved despite a higher ignition pressure configuration. The BMW X5 M50d reaches the 100 km/h mark in only 5.4 seconds. With a standardised fuel consumption of 7.5 litres per 100 km, it is at least 18% below its 8-cylinder competitors. With an acceleration of 0 to 100 km/h in 4.7 seconds and a standardised fuel consumption of 6.3 litres per 100 km, the BMW M550d xDrive is unrivalled in its category. In the BMW 5 Series, the new diesel drivetrain is offered exclusively in the exhaust emission level EU6. The new BMW TwinPower Turbo diesel variant drivetrain is a perfect example of the BMW EfficientDynamics strategy. A strong sporting character and a high degree of supremacy in combination with low fuel consumption that remains unsurpassed in this segment. (orig.)

  18. General vs health specialized search engine: a blind comparative evaluation of top search results.

    Science.gov (United States)

    Pletneva, Natalia; Ruiz de Castaneda, Rafael; Baroz, Frederic; Boyer, Celia

    2014-01-01

    This paper presents the results of a blind comparison of top ten search results retrieved by Google.ch (French) and Khresmoi for everyone, a health specialized search engine. Participants--students of the Faculty of Medicine of the University of Geneva had to complete three tasks and select their preferred results. The majority of the participants have largely preferred Google results while Khresmoi results showed potential to compete in specific topics. The coverage of the results seems to be one of the reasons. The second being that participants do not know how to select quality and transparent health web pages. More awareness, tools and education about the matter is required for the students of Medicine to be able to efficiently distinguish trustworthy online health information.

  19. A top-down approach to crystal engineering of a racemic Δ2-isoxazoline.

    Science.gov (United States)

    Lombardo, Giuseppe M; Rescifina, Antonio; Chiacchio, Ugo; Bacchi, Alessia; Punzo, Francesco

    2014-02-01

    The crystal structure of racemic dimethyl (4RS,5RS)-3-(4-nitrophenyl)-4,5-dihydroisoxazole-4,5-dicarboxylate, C13H12N2O7, has been determined by single-crystal X-ray diffraction. By analysing the degree of growth of the morphologically important crystal faces, a ranking of the most relevant non-covalent interactions determining the crystal structure can be inferred. The morphological information is considered with an approach opposite to the conventional one: instead of searching inside the structure for the potential key interactions and using them to calculate the crystal habit, the observed crystal morphology is used to define the preferential lines of growth of the crystal, and then this information is interpreted by means of density functional theory (DFT) calculations. Comparison with the X-ray structure confirms the validity of the strategy, thus suggesting this top-down approach to be a useful tool for crystal engineering.

  20. A top-down approach in control engineering third-level teaching: The case of hydrogen-generation

    Science.gov (United States)

    Setiawan, Eko; Habibi, M. Afnan; Fall, Cheikh; Hodaka, Ichijo

    2017-09-01

    This paper presents a top-down approach in control engineering third-level teaching. The paper shows the control engineering solution for the issue of practical implementation in order to motivate students. The proposed strategy only focuses on one technique of control engineering to lead student correctly. The proposed teaching steps are 1) defining the problem, 2) listing of acquired knowledge or required skill, 3) selecting of one control engineering technique, 4) arrangement the order of teaching: problem introduction, implementation of control engineering technique, explanation of system block diagram, model derivation, controller design, and 5) enrichment knowledge by the other control techniques. The approach presented highlights hardware implementation and the use of software simulation as a self-learning tool for students.

  1. Effects of injection timing, before and after top dead center on the propulsion and power in a diesel engine

    Directory of Open Access Journals (Sweden)

    Nader Raeie

    2014-06-01

    Full Text Available It is well known that injection strategies including the injection timing and pressure play the most important role in determining engine performance, especially in pollutant emissions. However, the injection timing and pressure quantitatively affect the performance of diesel engine with a turbo charger are not well understood. In this paper, the fire computational fluid dynamics (CFD code with an improved spray model has been used to simulate the spray and combustion processes of diesel with early and late injection timings and six different injection pressure (from 275 bar to 1000 bar. It has been concluded that the use of early injection provides lower soot and higher NOx emissions than the late injection. In this study, it has been tried using the change of fuel injection time at these two next steps: before top dead center (BTDC and after top dead center (ATDC in order to achieving optimum emission and power in a specific point.

  2. Waste Receiving and Processing Facility, Module 1: Volume 5, Engineering studies

    International Nuclear Information System (INIS)

    1992-03-01

    The WRAP facility at Hanford will retrieve, process, certify transuranic, mixed, and low level radioactive wastes for disposal/either on-site or at the WIPP. The Conceptual Design Report for the Waste Receiving And Processing Facility, Module 1 (WRAP 1), established the technical benchmark. The UE ampersand C Engineering Proposal/Work Plan proposed twenty Evaluation/Optimization Engineering Studies to evaluate design alternatives and critically examine functional performance requirements prior to commencement of Preliminary Design. Of these twenty studies, one has been eliminated as unnecessary (The Use of Scintered Metal Filters) due mainly to the lack of National Standards and to the fact that standard HEPA type filters are totally adequate for WRAP application. This report presents an executive summary of the remaining nineteen studies

  3. The Top 100 Business, Education, Engineering and Social Sciences Degrees Conferred on Hispanic Students

    Science.gov (United States)

    Diverse: Issues in Higher Education, 2011

    2011-01-01

    Each year, "Diverse: Issues In Higher Education" publishes lists of the Top 100 producers of associate, bachelor's and graduate degrees awarded to minority students based on research conducted by Dr. Victor M. H. Borden, professor of educational leadership and policy studies at Indiana University Bloomington. This article presents lists of the top…

  4. Value-Chain Engineering of a Tower-Top Cellular Base Station System

    OpenAIRE

    Cooper, Tim; Farrell, Ronan

    2007-01-01

    In this paper we present a value chain analysis of mobile `phone basestations, with a focus on possible antenna based tower-top electronics. Through this analysis we are able to present a number of possible architectural solutions and provide guidance on performance and reliability criterion

  5. Taking It to the Top: A Lesson in Search Engine Optimization

    Science.gov (United States)

    Frydenberg, Mark; Miko, John S.

    2011-01-01

    Search engine optimization (SEO), the promoting of a Web site so it achieves optimal position with a search engine's rankings, is an important strategy for organizations and individuals in order to promote their brands online. Techniques for achieving SEO are relevant to students of marketing, computing, media arts, and other disciplines, and many…

  6. Conceptual engineering design study of thermionic topping of fossil power plants

    Energy Technology Data Exchange (ETDEWEB)

    1978-02-15

    Primary objectives of this study are to investigate alternative design concepts of thermal coupling of thermionic energy converters (TECs) to the steam cycle and the mechanical and electrical aspects of integrating TEC design into the steam power station. The specific tasks include: (1) evaluate design concepts of TEC topping of solvent refined liquified coal-fired steam power plants, with main emphasis devoted to thermal, mechanical, and electrical design aspects. (2) Develop preliminary conceptual design of a modular TEC assembly. (3) Develop preliminary cost estimates of the design modification to a liquified coal-fired steam power plant with TEC topping. (4) Provide support to Thermo Electron Corporation in planning TEC hardware testing. Results are presented in detail.

  7. Brian M. Kleiner receives Ralph H. Bogle Professor Fellowship in Industrial and Systems Engineering

    OpenAIRE

    Owczarski, Mark

    2010-01-01

    Brian M. Kleiner, professor of industrial and systems engineering in the College of Engineering at Virginia Tech, has been named the Ralph H. Bogle Professor Fellow in Industrial and Systems Engineering by the Virginia Tech Board of Visitors.

  8. Engine including a piston member having a high top ring groove

    Energy Technology Data Exchange (ETDEWEB)

    Weber, R.L.; Kamman, K.R.; Ballheimer, B.; Shoup, S.G.

    1990-07-17

    This patent describes an improvement in an engine. It is of the type having a block defining an upper bore, a cylinder liner located in the block bore and defining a piston bore, a cylinder head connected to the block, and a piston assembly including a steel piston member disposed for reciprocation in the piston bore.

  9. Effect of the piston top contour on the tumble flow and combustion features of a GDI engine with a CMCV: a CFD study

    Directory of Open Access Journals (Sweden)

    Congbo Yin

    2016-01-01

    Full Text Available In spite of much progress in the development of gasoline direct injection (GDI engines, choosing an appropriate piston top contour to obtain desirable combustion efficiency is still an arduous process for engineers. This study investigates the combined effects of piston bowl geometry and a charge motion control valve (CMCV on tumble flow and combustion features in GDI engines. Based on the model validation, the processes of intake, spray, mixture formation and combustion at different engine speeds are simulated and analyzed for different piston shapes for the two cases of opening and closing the CMCV. The results show that the bowl on the top of piston is beneficial for the formation and development of tumble flow. The flat top piston with the CMCV closed is able to achieve acceptable combustion pressure. However, with the increase of engine speed and load, the advantages of the flat top pistons gradually disappear; the dual offset bowl piston has a minimum tumble ratio and turbulence kinetic energy (TKE at the end of the compression stroke because of the projection in the middle of the piston top surface which leads to a lower pressure rise rate and a reduced flame propagation speed at high load. The closed CMCV contributes to a faster evaporation rate and a more uniform mixture at lower speeds. It is not recommended for use at high speeds due to lower intake air mass and reduced combustion pressure. The research provides an effective way for engineers to choose an appropriate piston top contour combined with a CMCV to obtain desirable combustion efficiency.

  10. Calage thermodynamique du point mort haut des moteurs à piston Thermodynamic Calibration of Top Dead Center in Piston Engines

    Directory of Open Access Journals (Sweden)

    Pinchon P.

    2006-11-01

    Full Text Available Lorsqu'on utilise un système d'acquisition rapide de données sur moteur, il se pose souvent le problème d'associer des grandeurs calculées, comme le volume de la chambre de combustion, à des grandeurs mesurées comme la pression dans le cylindre. II est alors indispensable de synchroniser avec une grande précision absolue ces deux grandeurs en repérant avec soin au moins un point de référence de la cinématique bielle-manivelle. Dans la méthode développée ici on a choisi de déterminer la position angulaire du vilebrequin correspondant au Point Mort Haut (PMH grâce à l'exploitation du signal de pression-cylindre acquis en compression-détente sans combustion, le moteur étant entraîné en rotation. Le principe du calage consiste à calculer l'écart existant entre le PMH et l'angle de la pression maximale qui est aisément repérable. Basée sur des considérations thermodynamiques théoriques, cette méthode de calage a été testée avec succès au cours d'essais effectués sur divers moteurs dont on a fait varier en particulier le rapport volumétrique, le remplissage et les pertes à la segmentation. La précision de la méthode est de l'ordre de 1/10e de degré de rotation vilebrequin. When a fast data-acquisition system is used for an engine, the problem often arises of associating both calculated data, such as combustion chamber volume, and measured data, such as pressure inside the cylinder. It then becomes indispensable to synchronize these two data with great absolute accuracy by carefully determining at least a reference point in the kinematics of the connecting-rod/crank shaft assembly. In the method developed here, we have chosen to determine the angular position of the crankshaft corresponding to top dead center (TDC by making use of the cylinder-pressure signal recorded during compression/expansion without combustion for motored engine. The calibration principle consists in calculating the shift between TDC and the

  11. Waste Receiving and Processing Facility, Module 1: Volume 6, Engineering assessments

    International Nuclear Information System (INIS)

    1992-03-01

    This report evaluates the ability of the WRAP Module 1 Facility to achieve the required material throughput by developing a time and motion simulation model of the facility using the WITNESS Simulation Program. Analysis of the simulation model indicated that the required throughput of 6825 drums per year based on working 5.5 hours in the Shipping ampersand Receiving and Waste Process areas and 7 hours in the NDA/NDE area for 175 days a year, as stated in the Functional Design Criteria (FDC) Rev. 1 and Supplemental Design Requirements Document (SDRD) Rev. 1, can be achieved

  12. Ekspedeerimisfirmade TOP

    Index Scriptorium Estoniae

    2008-01-01

    Ekspedeerimisfirmade TOP 57. Vt. samas: Tanel Raig. Majandus kukutab ekspedeerimisturgu. Diagramm: Väliskaubanduse statistika; Katrin Raie. Ekspedeerijad hakkavad rohkem koostööle rõhuma. Kommenteerib Jaan Lepp; Müügitulu TOP 10; Müügitulu kasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Eestis registreeritud Vene hiiglane; Ekspedeerimisturu kasumiliider kaotas 20 miljonit; Küsimustele vastab OÜ Contimer juht Dmitri Redkin

  13. The sources and popularity of online drug information: an analysis of top search engine results and web page views.

    Science.gov (United States)

    Law, Michael R; Mintzes, Barbara; Morgan, Steven G

    2011-03-01

    The Internet has become a popular source of health information. However, there is little information on what drug information and which Web sites are being searched. To investigate the sources of online information about prescription drugs by assessing the most common Web sites returned in online drug searches and to assess the comparative popularity of Web pages for particular drugs. This was a cross-sectional study of search results for the most commonly dispensed drugs in the US (n=278 active ingredients) on 4 popular search engines: Bing, Google (both US and Canada), and Yahoo. We determined the number of times a Web site appeared as the first result. A linked retrospective analysis counted Wikipedia page hits for each of these drugs in 2008 and 2009. About three quarters of the first result on Google USA for both brand and generic names linked to the National Library of Medicine. In contrast, Wikipedia was the first result for approximately 80% of generic name searches on the other 3 sites. On these other sites, over two thirds of brand name searches led to industry-sponsored sites. The Wikipedia pages with the highest number of hits were mainly for opiates, benzodiazepines, antibiotics, and antidepressants. Wikipedia and the National Library of Medicine rank highly in online drug searches. Further, our results suggest that patients most often seek information on drugs with the potential for dependence, for stigmatized conditions, that have received media attention, and for episodic treatments. Quality improvement efforts should focus on these drugs.

  14. Grain size engineering of bcc refractory metals: Top-down and bottom-up-Application to tungsten

    International Nuclear Information System (INIS)

    Kecskes, L.J.; Cho, K.C.; Dowding, R.J.; Schuster, B.E.; Valiev, R.Z.; Wei, Q.

    2007-01-01

    We have used two general methodologies for the production of ultrafine grained (UFG) and nanocrystalline (NC) tungsten (W) metal samples: top-down and bottom-up. In the first, Equal channel angular extrusion (ECAE), coupled with warm rolling has been used to fabricate UFG W, and high pressure torsion (HPT) was used to fabricate NC W. We demonstrate an abrupt shift in the deformation mechanism, particularly under dynamic compressive loading, in UFG and NC W. This novel deformation mechanism, a dramatic transition from a uniform deformation mode to that of localized shearing, is shared by other UFG and NC body-centerd cubic (BCC) metals. We have also conducted a series of bottom-up experiments to consolidate powdered UFG W precursors into solid bodies. The bottom-up approach relies on rapid, high-temperature consolidation, specifically designed for UFG and NC W powders. The mechanical property results from the top-down UFG and NC W were used as minimum property benchmarks to guide and design the experimental protocols and parameters for use in the bottom-up procedures. Preliminary results, showing rapid grain growth during the consolidation cycle, did not achieve full density in the W samples. Further development of high-purity W nanopowders and appropriate grain-growth inhibitors (e.g., Zener pinning) will be required to successfully produce bulk-sized UFG and NC W samples

  15. Phase structuring in metal alloys: Ultrasound-assisted top-down approach to engineering of nanostructured catalytic materials.

    Science.gov (United States)

    Cherepanov, Pavel V; Andreeva, Daria V

    2017-03-01

    High intensity ultrasound (HIUS) is a novel and efficient tool for top-down nanostructuring of multi-phase metal systems. Ultrasound-assisted structuring of the phase in metal alloys relies on two main mechanisms including interfacial red/ox reactions and temperature driven solid state phase transformations which affect surface composition and morphology of metals. Physical and chemical properties of sonication medium strongly affects the structuring pathways as well as morphology and composition of catalysts. HIUS can serve as a simple, fast, and effective approach for the tuning of structure and surface properties of metal particles, opening the new perspectives in design of robust and efficient catalysts. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Kinnisvarafirmade TOP 90

    Index Scriptorium Estoniae

    2002-01-01

    TOP 90. Kinnisvara valdkondade TOP 5. Käibe TOP 30. Käibe kasvu TOP 30. Rentaabluse TOP 30. Kasumi TOP 30. Kasumi kasvu TOP 30. Varade tootlikkuse TOP 30. Kinnisvarafirmade üldandmed. Kinnisvarafirmade finantsandmed

  17. Kinnisvarafirmade TOP 90

    Index Scriptorium Estoniae

    2003-01-01

    Kinnisvarafirmade TOP 90. Rentaabluse TOP 30. Käibe TOP 30. Käibe kasvu TOP 30. Kasumi TOP 30. Kasumi kasvu TOP 30. Varade tootlikkuse TOP 30. Kinnisvarafirmade üldandmed. Kinnisvarafirmade finantsandmed

  18. Teedeehitusfirmade TOP 24

    Index Scriptorium Estoniae

    2006-01-01

    Teedeehitusfirmade TOP. Vt. samas: Käibe TOP 10; Käibe kasvu TOP 10; Kasumi TOP 10; Kasumi Kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Teedeehitusfirmade üld- ja finantsandmed

  19. Koolitusfirmade TOP 50

    Index Scriptorium Estoniae

    2006-01-01

    Koolitusfirmade TOP. Vt. samas: Käibe TOP 10; Käibe kasvu TOP 10; Majandustegevuse kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Koolitusfirmade üld- ja finantsandmed

  20. Telekommunikatsiooni TOP aastal 2003

    Index Scriptorium Estoniae

    2004-01-01

    Telekommunikatsiooni TOP aastal 2003. Käibe TOP 10. Käibe kasvu TOP 10. Rentaabluse TOP 10. Kasumi TOP 10. Kasumi kasvu TOP 10. Omakapitali tootlikkuse TOP 10. Telekommunikatsioonifirmade üldandmed. Telekommunikatsioonifirmade finantsandmed

  1. Põllumajandustootjate TOP 50

    Index Scriptorium Estoniae

    2006-01-01

    Põllumajandustootjate TOP. Vt. samas: Käibe TOP 10; Käibe kasvu TOP 10; Majandustegevuse kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Põllumajandustootjate üld- ja finantsandmed

  2. Ehitusmaterjalitootjate TOP 95

    Index Scriptorium Estoniae

    2006-01-01

    Ehitusmaterjalitootjate TOP. Vt. samas: Käibe TOP 10; Käibe kasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Ehitusmaterjalitootjate üld- ja finantsandmed

  3. Engineering Task Plan for the Integrity Assessment Examination of Double-Contained Receiver Tanks (DCRT), Catch Tanks and Ancillary facilities

    International Nuclear Information System (INIS)

    BECKER, D.L.

    2000-01-01

    This Engineering Task Plan (ETP) presents the integrity assessment examination of three DCRTs, seven catch tanks, and two ancillary facilities located in the 200 East and West Areas of the Hanford Site. The integrity assessment examinations, as described in this ETP, will provide the necessary information to enable the independently qualified registered professional engineer (IQRPE) to assess the condition and integrity of these facilities. The plan is consistent with the Double-Shell Tank Waste Transfer Facilities Integrity Assessment Plan

  4. Metabolic engineering of E. coli top 10 for production of vanillin through FA catabolic pathway and bioprocess optimization using RSM.

    Science.gov (United States)

    Chakraborty, Debkumar; Gupta, Gaganjot; Kaur, Baljinder

    2016-12-01

    Metabolic engineering and construction of recombinant Escherichia coli strains carrying feruloyl-CoA synthetase and enoyl-CoA hydratase genes for the bioconversion of ferulic acid to vanillin offers an alternative way to produce vanillin. Isolation and designing of fcs and ech genes was carried out using computer assisted protocol and the designed vanillin biosynthetic gene cassette was cloned in pCCIBAC expression vector for introduction in E. coli top 10. Recombinant strain was implemented for the statistical optimization of process parameters influencing F A to vanillin biotransformation. CCD matrix constituted of process variables like FA concentration, time, temperature and biomass with intracellular, extracellular and total vanillin productions as responses. Production was scaled up and 68 mg/L of vanillin was recovered from 10 mg/L of FA using cell extracts from 1 mg biomass within 30 min. Kinetic activity of enzymes were characterized. From LCMS-ESI analysis a metabolic pathway of FA degradation and vanillin production was predicted. Copyright © 2016 Elsevier Inc. All rights reserved.

  5. A Poisoned Chalice? Why UK Women Engineering and Technology Students May Receive More "Help" than Their Male Peers

    Science.gov (United States)

    Powell, Abigail; Dainty, Andrew; Bagilhole, Barbara

    2011-01-01

    The UK engineering and technology (E&T) sector is male-dominated, with women facing various cultural and structural barriers in entering and developing their careers within it. Existing research in this area has focused on women's recruitment or retaining women in employment, but little has addressed women's transition to industry through the…

  6. Top Earners

    DEFF Research Database (Denmark)

    Badel, Alejandro; Daly, Moira; Huggett, Mark

    of the earnings distribution becomes thicker with age, and (3) the growth rate of earnings over the working lifetime is larger for groups with higher lifetime earnings. Models of top earners should account for these qualitative patterns and, importantly, for how they quantitatively differ across countries....

  7. Electronic warfare receivers and receiving systems

    CERN Document Server

    Poisel, Richard A

    2014-01-01

    Receivers systems are considered the core of electronic warfare (EW) intercept systems. Without them, the fundamental purpose of such systems is null and void. This book considers the major elements that make up receiver systems and the receivers that go in them.This resource provides system design engineers with techniques for design and development of EW receivers for modern modulations (spread spectrum) in addition to receivers for older, common modulation formats. Each major module in these receivers is considered in detail. Design information is included as well as performance tradeoffs o

  8. Autotranspordifirmade TOP 100

    Index Scriptorium Estoniae

    2006-01-01

    Ilmunud ka: Delovõje Vedomosti : Transport i Logistika 29. nov. lk. 10-11. Autofirmade TOP 100. Vt. samas: Käibe TOP 10; Käibe kasvu TOP 10; Majandustegevuse kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Autotranspordifirmade üld- ja finantsandmed. Delovõje Vedomosti : Transport i Logistika sisaldab tabelit Autofirmade TOP 100

  9. EXPERIENCE OF APPLICATION OF FOREIGN MODELS OF STIMULATION OF WORK OF TOP-MANAGERS AT THE RUSSIAN ENTERPRISE OF HEAVY MECHANICAL ENGINEERING

    Directory of Open Access Journals (Sweden)

    A.A. Levchenko

    2009-09-01

    Full Text Available For today many domestic enterprises of sphere of production of goods feel sharp need for change of system of stimulation of work of the organization. Foreign experience of stimulation of work of top-managers is actively made use. In clause the example of application of the adapted foreign system of awarding of top-managers at the Russian enterprise is presented on the basis of regulations about of motivation of key heads business-battalions corporations.

  10. The Audi 3.0l TFSI - the new top-of-the-range V6 engine; Der Audi 3,0l TFSI - die neue V6 Spitzenmotorisierung

    Energy Technology Data Exchange (ETDEWEB)

    Fitzen, M.; Hatz, W.; Eiser, A.; Heiduk, T.; Riegner, J. [Audi AG, Ingolstadt (Germany)

    2008-07-01

    The 3.0l TFSI represents the new top-of-the-range V6 engine from Audi. In its basic form this engine design delivers 213 kW (290 bhp) and 420 Nm. The fundamental design of the engine has been adopted from the naturally aspirated V6 engines as revised in 2006, including the measures to reduce frictional losses. An entirely new development is the supercharger module, with integrated Roots blower, bypass regulation and charge air intercooling. All the components are accommodated inside the V. As a result of the extremely compact dimensions it has also been possible to adopt the arrangement of the inlet and exhaust systems directly from the naturally aspirated engines without any changes. In conjunction with direct injection, this sets new standards in terms of responsiveness, efficiency and noise levels. The new Audi V6 3.0l TFSI combines excellent torque and power output with outstanding responsiveness, along with the package and exhaust-related benefits of a naturally aspirated engine. That makes it ideally suitable for a wide range of applications within the Audi model portfolio. The initial launch of the engine will be in the new A6 for the autumn of 2008. (orig.)

  11. Autotranspordi TOP aastal 2007

    Index Scriptorium Estoniae

    2008-01-01

    TOP 50. Vt. samas: Käibe TOP 10; Käibe kasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Marika Roomere. Täisteenuse pakkumine kergitas tulemusi; Jupiter Plus otsib järjest uusi kasvuvõimalusi; EST-Trans Kaubaveod teenib kasumit toiduvedamisega

  12. Koolitusfirmade TOP aastal 2007

    Index Scriptorium Estoniae

    2008-01-01

    Koolitusfirmade TOP. Vt. samas: Käibe TOP 10; Käibekasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Signe Sillasoo. Invicta tahab lähiaastail laieneda Eestis ja mujalgi; Ketlin Priilinn. Addenda kasutas ära majanduse soodsa seisu. Kommenteerib Heli Sõmer. Juhtide hoiakute muutmisega tõus esikolmikusse

  13. Audiitorfirmade TOP aastal 2007

    Index Scriptorium Estoniae

    2008-01-01

    Audiitorfirmade TOP 51. Vt. samas: Urve Vilk. Audiitoriteni pole majanduslangus jõudnud; Intervjuu I.S. Audiitorteenuste OÜ omaniku Irina Somovaga; Käibe TOP 10; Käibe kasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10

  14. Koolitusfirmade TOP aastal 2006

    Index Scriptorium Estoniae

    2007-01-01

    Koolitusfirmade TOP. Vt. samas: Käibe TOP10; Käibe kasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Varade tootlikkuse TOP 10; Pille Rõivas. Võtmetegur meeskond; Vain & Partnerid: uudsus peitub sisus; Kristo Kiviorg. Teel Baltimaade koolitajate tippu

  15. Top reconstruction and boosted top experimental overview

    CERN Document Server

    Skinnari, Louise

    2015-01-01

    An overview of techniques used to reconstruct resolved and boosted top quarks is presented. Techniques for resolved top quark reconstruction include kinematic likelihood fitters and pseudo- top reconstruction. Many tools and methods are available for the reconstruction of boosted top quarks, such as jet grooming techniques, jet substructure variables, and dedicated top taggers. Different techniques as used by ATLAS and CMS analyses are described and the performance of different variables and top taggers are shown.

  16. Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Engineering Test Report: Radiated Emissions and SARR, SARP, DCS Receivers, Link Frequencies EMI Sensitive Band Test Results, AMSU-A1, S/N 108 2

    Science.gov (United States)

    Valdez, A.

    2000-01-01

    This is the Engineering Test Report, Radiated Emissions and SARR, SARP, DCS Receivers, Link Frequencies EMI Sensitive Band Test Results, AMSU-A1 SIN 108, for the Integrated Advanced Microwave Sounding Unit-A (AMSU-A).

  17. Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Engineering Test Report: Radiated Emissions and SARR, SARP, DCS Receivers, Link Frequencies EMI Sensitive Band Test Results, AMSU-A1, S/N 109

    Science.gov (United States)

    Valdez, A.

    2000-01-01

    This is the Engineering Test Report, Radiated Emissions and SARR, SARP, DCS Receivers, Link Frequencies EMI Sensitive Band Test Results, AMSU-A1, S/N 109, for the Integrated Advanced Microwave Sounding Unit-A (AMSU-A).

  18. Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Engineering Test Report: Radiated Emissions and SARR, SARP, DCS Receivers, Link Frequencies EMI Sensitive Band Test Results, AMSU-A2, S/N 108, 08

    Science.gov (United States)

    Valdez, A.

    2000-01-01

    This is the Engineering Test Report, Radiated Emissions and SARR, SARP, DCS Receivers, Link Frequencies EMI Sensitive Band Test Results, AMSU-A2, S/N 108, for the Integrated Advanced Microwave Sounding Unit-A (AMSU-A).

  19. Books Received

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education. Books Received. Articles in Resonance – Journal of Science Education. Volume 1 Issue 1 January 1996 pp 118-118 Books Received. Books Received · More Details Fulltext PDF. Volume 1 Issue 2 February 1996 pp 120-120 Books Received. Books Received.

  20. A top-down system engineering approach as an alternative to the tradiotinal over-the-bench methodology for the design of a building

    NARCIS (Netherlands)

    Bluyssen, P.M.; Oostra, M.A.R.; Böhms, H.M.

    2010-01-01

    The traditional over-the-bench methodology for the design of a building is resulting in failure costs, failures at delivery and severe problems. An interactive top-down approach is required, both for the communication process necessary to facilitate the design, construction, maintenance and

  1. Top flooding modeling with MAAP4 code

    International Nuclear Information System (INIS)

    Brunet-Thibault, E.; Marguet, S.

    2006-01-01

    An engineering top flooding model was developed in MAAP4.04d.4, the severe accident code used in EDF, to simulate the thermal-hydraulic phenomena that should take place if emergency core cooling (ECC) water was injected in hot leg during quenching. In the framework of the ISTC (International Science and Technology Centre), a top flooding test was proposed in the PARAMETER facility (Podolsk, Russia). The MAAP calculation of the PARAMETER top flooding test is presented in this paper. A comparison between top and bottom flooding was made on the bundle test geometry. According to this study, top flooding appears to cool quickly and effectively the upper plenum internals. (author)

  2. Arvutifirmade TOP 101 aastal 2004

    Index Scriptorium Estoniae

    2005-01-01

    Arvutifirmade TOP 101; Käibe TOP 20; Käibe kasvu TOP 15; Kasumi TOP 15; Rentaabluse TOP 20; Kasumi kasvu TOP 15; Omakapiali tootlikkuse TOP 15; Eesti arvutifirmade finantsandmed; Arvutifirmade üldandmed

  3. Jaekaubanduse TOP 100 aastal 2001

    Index Scriptorium Estoniae

    2002-01-01

    TOP 100. Käibe TOP 30. Käibe kasvu TOP 30. Kasumi TOP 30. Kasumi kasvu TOP 30. Rentaabluse TOP 30. Varade tootlikkuse TOP 30. Jaekaubandusettevõtete finantsseadmed. Jaekaubandusettevõtete üldandmed

  4. Jaekaubandusettevõtete TOP 70

    Index Scriptorium Estoniae

    2005-01-01

    Jaekaubandusettevõtete TOP 70; Käibe TOP 25; Kasumi TOP 25; Käibe kasvu TOP 20; Kasumi kasvu TOP 20; Rentaabluse TOP 20; Omakapitali tootlikkuse TOP 20; Jaekaubandusettevõtete üld- ja finantsandmed

  5. Majutusasutuste TOP 40 aastal 2002

    Index Scriptorium Estoniae

    2003-01-01

    Majutusasutuste TOP 40 aastal 2002. Käibe TOP 40. Kasumi TOP 40. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Majutusasutuste üldandmed. Majutusasutuste finantsandmed

  6. Top-Down and Bottom-Up Approaches in Engineering 1 T Phase Molybdenum Disulfide (MoS2 ): Towards Highly Catalytically Active Materials.

    Science.gov (United States)

    Chua, Chun Kiang; Loo, Adeline Huiling; Pumera, Martin

    2016-09-26

    The metallic 1 T phase of MoS2 has been widely identified to be responsible for the improved performances of MoS2 in applications including hydrogen evolution reactions and electrochemical supercapacitors. To this aim, various synthetic methods have been reported to obtain 1 T phase-rich MoS2 . Here, the aim is to evaluate the efficiencies of the bottom-up (hydrothermal reaction) and top-down (chemical exfoliation) approaches in producing 1 T phase MoS2 . It is established in this study that the 1 T phase MoS2 produced through the bottom-up approach contains a high proportion of 1 T phase and demonstrates excellent electrochemical and electrical properties. Its performance in the hydrogen evolution reaction and electrochemical supercapacitors also surpassed that of 1 T phase MoS2 produced through a top-down approach. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Reisifirmade TOP 40 aastal 2002

    Index Scriptorium Estoniae

    2003-01-01

    Reisifirmade TOP 40 aastal 2002. Reisifirmade TOP-i esikümme. Käibe TOP 40. Kasumi TOP 40. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Reisifirmade üldandmed. Reisifirmade finantsandmed. Tehnilise käibe alusel arvutatud edetabelid: Reisifirmade TOP 25; Käibe TOP 40; Rentaabluse TOP 10; Käibe kasvu TOP 10

  8. Diversity receiver

    NARCIS (Netherlands)

    2005-01-01

    The invention is directed to the reception of high rate radio signals (for example DVB-T signals) while the receiver is moving at a high speed (for example in or with a car). Two or more antennas (12, 16) are closely spaced and arranged behind each other in the direction of motion (v) for receiving

  9. Intergenerational Top Income Persistence

    DEFF Research Database (Denmark)

    Munk, Martin D.; Bonke, Jens; Hussain, M. Azhar

    2016-01-01

    In this paper, we investigate intergenerational top earnings and top income mobility in Denmark. Access to administrative registers allowed us to look at very small fractions of the population. We find that intergenerational mobility is lower in the top when including capital income in the income...... measure— for the rich top 0.1% fathers and sons the elasticity is 0.466. Compared with Sweden, however, the intergenerational top income persistence is about half the size in Denmark....

  10. TiN/Al2O3/ZnO gate stack engineering for top-gate thin film transistors by combination of post oxidation and annealing

    Science.gov (United States)

    Kato, Kimihiko; Matsui, Hiroaki; Tabata, Hitoshi; Takenaka, Mitsuru; Takagi, Shinichi

    2018-04-01

    Control of fabrication processes for a gate stack structure with a ZnO thin channel layer and an Al2O3 gate insulator has been examined for enhancing the performance of a top-gate ZnO thin film transistor (TFT). The Al2O3/ZnO interface and the ZnO layer are defective just after the Al2O3 layer formation by atomic layer deposition. Post treatments such as plasma oxidation, annealing after the Al2O3 deposition, and gate metal formation (PMA) are promising to improve the interfacial and channel layer qualities drastically. Post-plasma oxidation effectively reduces the interfacial defect density and eliminates Fermi level pinning at the Al2O3/ZnO interface, which is essential for improving the cut-off of the drain current of TFTs. A thermal effect of post-Al2O3 deposition annealing at 350 °C can improve the crystalline quality of the ZnO layer, enhancing the mobility. On the other hand, impacts of post-Al2O3 deposition annealing and PMA need to be optimized because the annealing can also accompany the increase in the shallow-level defect density and the resulting electron concentration, in addition to the reduction in the deep-level defect density. The development of the interfacial control technique has realized the excellent TFT performance with a large ON/OFF ratio, steep subthreshold characteristics, and high field-effect mobility.

  11. Queen's discovery lauded by top scientific journal

    CERN Multimedia

    McGrady, S

    2002-01-01

    A scientific breakthrough at Queen's University's Sudbury Neutrino Observatory has received major international recognition. The journal Science ranked the discovery that cracked the "neutrino problem" second, in the journal's top 10 scientific achievements of 2002 (1/2 page).

  12. Top quark property measurements in single top

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00386283; The ATLAS collaboration

    2016-01-01

    A review of the recent results on measurements of top quark properties in single top quark processes, performed at the LHC by ATLAS and CMS is presented. The measurements are in good agreement with predictions and no deviations from Standard Model expectations have been observed.

  13. Audiitorfirmade TOP 50 aastal 2000

    Index Scriptorium Estoniae

    2001-01-01

    Audiitorfirmade käibe TOP 50, käibe kasvu TOP 25, käibe languse TOP 15, kasumi TOP 50, kasumi kasvu TOP 10, kasumi languse TOP 10, audiitorfirmade finantsnäitajad. Rentaabluse TOP 50, varade tootlikkuse TOP 50

  14. Top Production at LHCb

    CERN Multimedia

    Santana Rangel, Murilo

    2015-01-01

    Single and pair top production in the forward direction at the LHC allows for precision tests of the Standard Model. The observation of top quarks in 7 and 8 TeV data and prospects for precision measurements are shown.

  15. Top Physics at Atlas

    CERN Document Server

    Romano, M; The ATLAS collaboration

    2013-01-01

    This talk is an overview of recent results on top-quark physics obtained by the ATLAS collaboration from the analysis of p-p collisions at 7 and 8 TeV at the Large Hadron Collider. Total and differential top pair cross section, single top cross section and mass measurements are presented.

  16. CDF Top Physics

    Science.gov (United States)

    Tartarelli, G. F.; CDF Collaboration

    1996-05-01

    The authors present the latest results about top physics obtained by the CDF experiment at the Fermilab Tevatron collider. The data sample used for these analysis (about 110 pb{sup{minus}1}) represents almost the entire statistics collected by CDF during four years (1992--95) of data taking. This large data size has allowed detailed studies of top production and decay properties. The results discussed here include the determination of the top quark mass, the measurement of the production cross section, the study of the kinematics of the top events and a look at top decays.

  17. Turismifirmade 2000. a. TOP 30

    Index Scriptorium Estoniae

    2001-01-01

    Turismiettevõtete üldandmed: turismiettevõtete finantsnäitajad; käibe TOP 30; käibe kasvu TOP 10; kasumi TOP 20; kasumi kasvu TOP 10; kasumi languse TOP; rentaabluse TOP 10; varade tootlikkuse TOP 10

  18. Ehitusmaterjalitootjate TOP 70 aastal 2003

    Index Scriptorium Estoniae

    2004-01-01

    Ilmunud ka: Delovõje Vedomosti : Stroitelstvo, 29. sept. 2004, lk. 2,4. Ehitusmaterjalitootjate TOP 70; Käibe TOP 10; Käibe kasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP. Ehitusmaterjalitootjate üldandmed

  19. The analysis of results received from the programme for calculating the concentration of pollutants from vehicles with internal combustion engines on the crossroads in urban environments

    International Nuclear Information System (INIS)

    Tashevski, Done; Dimitrovski, Mile

    1995-01-01

    The analysis of results and influence of specified factors on the concentration of pollutants on the crossroads with chosen characteristic conditions has been made, on the basis of the programme for calculating the concentration of pollutants from vehicles with internal combustion engines on the crossroads in urban environments. (author)

  20. TOP LINAC design; Progetto del TOP LINAC

    Energy Technology Data Exchange (ETDEWEB)

    Picardi, L; Ronsivalle, C; Vignati, A [ENEA, Centro Ricerche Frascati, Rome (Italy). Dip. Innovazione

    1997-11-01

    The report describes a linear accelerator for protons named TOP LINAC designed for the TOP (Terapia Oncologica con Protoni, Oncological Protontherapy) project launched by the Italian National Institute of Health (Istituto Superiore di Sanita`, ISS) to explore in collaboration with the biggest Oncological Hospital in Rome (Istituto Regina Elena, IRE) the potentialities of the therapy with accelerated protons and establish guide lines for the application of this new type of radiotherapy in comparison with the more traditional electron and x-rays radiotherapy. The concept of a compact accelerator for protontherapy applications bore within the Italian Hadrontherapy Collaboration (TERA Collaboration) with the aim to diffuse the protontherapy on the National territory. The ISS program plans to use the TOP linac proton beam also for production of PET (Positron Emission Tomography) radioisotopes and radiobiology studies. Official agreements are in course between ISS and ENEA which provides its experience in the industrial and medical accelerators for the design and the construction of the TOP linac. The accelerator that will be the first 3 GHz proton linac in the world, will be composed of a 428.3 MHz 7 Me V RFQ + DTL injector followed by a 7-65 Me V section of a 3 GHz SCDTL structure and a 65 - 200 Me V variable energy SCL 3 GHz structure. In particular the SCDTL section uses a highly innovative accelerating structure patented by ENEA. In this report the clinical and physical requests are discussed and a preliminary design of the whole machine is given.

  1. Ekspedeerimisettevõtete TOP 50

    Index Scriptorium Estoniae

    2006-01-01

    Ilmunud ka: Delovõje Vedomosti : Transport i Logistika nr. 11, 29. nov. lk. 32-35. Ekspedeerimisettevõtete TOP. Vt. samas: Käibe TOP 10; Käibekasvu TOP 10; Kasumi TOP 10; Kasumikasvu TOP 10; Rentaabluse TOP 10; ROE TOP 10; Ekspedeerimisettevõtete üld- ja finantsandmed. Ajal. Delovõje Vedomosti : Transport i Logistika toodud ainult Ekspedeerimisettevõtete TOP 50

  2. Top Quark Physics

    International Nuclear Information System (INIS)

    Larios, F.

    2006-01-01

    We give an overview of the physics of the Top quark, from the experimental discovery to the studies of its properties. We review some of the work done on the Electroweak and Flavor Changing couplings associated with the Top quark in the Standard Model and beyond. We will focus on the specific contribution of phycisits working in Mexico and Mexican physicists working abroad

  3. Top quark theory

    NARCIS (Netherlands)

    Laenen, E.

    2012-01-01

    The theoretical aspects of a number of top quark properties such as its mass and its couplings are reviewed. Essential aspects in the theoretical description of top quark production, singly, in pairs and in association, as well as its decay related to spin and angular correlations are discussed.

  4. Top physics at CDF

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, R.E. [Univ. of Rochester, NY (United States)

    1997-01-01

    We report on top physics results using a 100 pb{sup -1} data sample of p{bar p} collisions at {radical}s = 1.8 TeV collected with the Collider Detector at Fermilab (CDF). We have identified top signals in a variety of decay channels, and used these channels to extract a measurement of the top mass and production cross section. A subset of the data (67 pb{sup -1}) is used to determine M{sub top} = 176 {+-} 8(stat) {+-} 10(syst) and {sigma}(tt) = 7.6 {sub -2.0}{sup +2.4} pb. We present studies of the kinematics of t{bar t} events and extract the first direct measurement of V{sub tb}. Finally, we indicate prospects for future study of top physics at the Tevatron.

  5. Top Quark Mass

    CERN Document Server

    Mulders, Martijn

    2016-01-01

    Ever since the discovery of the top quark at the Tevatron collider in 1995 the measurement of its mass has been a high priority. As one of the fundamental parameters of the Standard Theory of particle physics, the precise value of the top quark mass together with other inputs provides a test for the self-consistency of the theory, and has consequences for the stability of the Higgs field that permeates the Universe. In this review I will briefly summarize the experimental techniques used at the Tevatron and the LHC experiments throughout the years to measure the top quark mass with ever improving accuracy, and highlight the recent progress in combining all measurements in a single world average combination. As experimental measurements became more precise, the question of their theoretical interpretation has become important. The difficulty of relating the measured quantity to the fundamental top mass parameter has inspired alternative measurement methods that extract the top mass in complementary ways. I wil...

  6. Top quark mass measurement

    International Nuclear Information System (INIS)

    Maki, Tuula; Helsinki Inst. of Phys.; Helsinki U. of Tech.

    2008-01-01

    The top quark is the heaviest elementary particle. Its mass is one of the fundamental parameters of the standard model of particle physics, and an important input to precision electroweak tests. This thesis describes three measurements of the top-quark mass in the dilepton decay channel. The dilepton events have two neutrinos in the final state; neutrinos are weakly interacting particles that cannot be detected with a multipurpose experiment. Therefore, the signal of dilepton events consists of a large amount of missing energy and momentum carried off by the neutrinos. The top-quark mass is reconstructed for each event by assuming an additional constraint from a top mass independent distribution. Template distributions are constructed from simulated samples of signal and background events, and parameterized to form continuous probability density functions. The final top-quark mass is derived using a likelihood fit to compare the reconstructed top mass distribution from data to the parameterized templates. One of the analyses uses a novel technique to add top mass information from the observed number of events by including a cross-section-constraint in the likelihood function. All measurements use data samples collected by the CDF II detector

  7. Table-top diffuse optical imaging

    NARCIS (Netherlands)

    Sturgeon, K.A.; Bakker, L.P.

    2006-01-01

    This report describes the work done during a six months internshipat Philips Research for a Masters in Electronic and Electrical Engineering. An existing table-top tomography system for measuring lightin phantom breasts was restored. Updated software control and image reconstruction software was

  8. Top physics in WHIZARD

    Energy Technology Data Exchange (ETDEWEB)

    Reuter, Juergen; Chokoufe Nejad, Bijan [DESY, Hamburg (Germany). Theory Group; Bach, Fabian [European Commission, Eurostat, Luxembourg (Luxembourg); Hoang, Andre [Vienna Univ. (Austria). Faculty of Physics; Vienna Univ. (Austria). Erwin Schroedinger International Inst. for Mathematical Physics; Kilian, Wolfgang [Siegen Univ. (Germany); Stahlhofen, Maximilian [Mainz Univ. (Germany). PRISMA Cluster of Excellence; Teubner, Thomas [Liverpool Univ. (United Kingdom). Dept. of Mathematical Sciences; Weiss, Christian [DESY, Hamburg (Germany). Theory Group; Siegen Univ. (Germany)

    2016-03-15

    In this talk we summarize the top physics setup in the event generator WHIZARD with a main focus on lepton colliders. This includes full six-, eight- and ten-fermion processes, factorized processes and spin correlations. For lepton colliders, QCD NLO processes for top quark physics are available and discussed. A special focus is on the top-quark pair threshold, where a special implementation combines a non-relativistic effective field theory calculation augmented by a next-to-leading threshold logarithm resummation with a continuum relativistic fixed-order QCD NLO simulation.

  9. Top physics in WHIZARD

    International Nuclear Information System (INIS)

    Reuter, Juergen; Chokoufe Nejad, Bijan; Hoang, Andre; Stahlhofen, Maximilian

    2016-03-01

    In this talk we summarize the top physics setup in the event generator WHIZARD with a main focus on lepton colliders. This includes full six-, eight- and ten-fermion processes, factorized processes and spin correlations. For lepton colliders, QCD NLO processes for top quark physics are available and discussed. A special focus is on the top-quark pair threshold, where a special implementation combines a non-relativistic effective field theory calculation augmented by a next-to-leading threshold logarithm resummation with a continuum relativistic fixed-order QCD NLO simulation.

  10. Top quark discovered

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    Nine months after a careful announcement of tentative evidence for the long-awaited sixth 'top' quark, physicists from the CDF and DO experiments at Fermilab's Tevatron proton-antiproton collider declared on 2 March that they had finally discovered the top quark. Last year (June 1994, page 1), the CDF experiment at the Tevatron reported a dozen candidate top events. These, said CDF, had all the characteristics expected of top, but the difficulties of extracting the tiny signal from a trillion proton-antiproton collisions made them shy of claiming a discovery. For its part, the companion DO Tevatron experiment reported a few similar events but were even more guarded about their interpretation as top quarks. Just after these hesitant announcements, performance at the Tevatron improved dramatically last summer. After the commissioning of a new linear accelerator and a magnet realignment, the machine reached a new world record proton-antiproton collision luminosity of 1.28 x 10 31 per sq cm per s, ten times that originally planned. Data began to pour in at an unprecedented rate and the data sample grew to six trillion collisions. Luminosity has subsequently climbed to 1.7 x 10 31 . The top quark is the final letter in the alphabet of Standard Model particles. According to this picture, all matter is composed of six stronglyinteracting subnuclear particles, the quarks, and six weakly interacting particles, the leptons. Both sextets are neatly arranged as three pairs in order of increasing mass. The fifth quark, the 'beauty' or 'b' quark, was also discovered at Fermilab, back in 1977. Since then physicists have been eagerly waiting for the top to turn up, but have been frustrated by its heaviness - the top is some 40 times the mass of its 'beautiful' partner. Not only is the top quark the heaviest by far, but it is the only quark which has been actively hunted. After the quarry was glimpsed last year, the net has now been

  11. Audiitorite TOP 50 aastal 2005

    Index Scriptorium Estoniae

    2006-01-01

    Audiitorite TOP. Vt. samas: Käibe TOP 10; Käibe kasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; ROE TOP 10; Ketlin Priilinn. Kasvu tagavad lojaalsed kliendid; Klient on audiitori parim müügimees; Teeli Remmelg. Kliendid vaatavad pigem kvaliteeti kui madalat hinda. Kommenteerivad Signe Keernik ja Kalle Lahe. Tabel: Audiitoriettevõtete üld- ja finantsandmed

  12. Jõgevamaa ettevõtete TOP 55

    Index Scriptorium Estoniae

    2004-01-01

    Jõgevamaa ettevõtete TOP 55 aastal 2003. Käibe TOP 40. Kasumi TOP 40. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Jõgevamaa firmade üld- ja finantsandmed

  13. Põlvamaa ettevõtete TOP 50

    Index Scriptorium Estoniae

    2004-01-01

    Ettevõtete TOP 50. Käibe TOP 40. Kasumi TOP 40. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Põlvamaa firmade üldandmed. Põlvamaa firmade finantsandmed

  14. Viljandimaa ettevõtete TOP 50

    Index Scriptorium Estoniae

    2005-01-01

    Viljandimaa ettevõtete TOP 50; Käibe TOP 35; Kasumi TOP 35; Käibe kasvu TOP 20; Kasumi kasvu TOP 20; Rentaabluse TOP 20; Omakapitali tootlikkuse TOP 20; Viljandimaa ettevõtete üld- ja finantsandmed

  15. Jõgevamaa ettevõtete TOP 50

    Index Scriptorium Estoniae

    2005-01-01

    Jõgevamaa ettevõtete TOP 50; Käibe TOP 35; Kasumi TOP 35; Käibe kasvu TOP 20; Kasumi kasvu TOP 20; Rentaabluse TOP 20; Omakapitali tootlikkuse TOP 20; Jõgevamaa ettevõtete üld- ja finantsandmed

  16. Boosted tops at ATLAS

    CERN Document Server

    Villaplana, M; The ATLAS collaboration

    2011-01-01

    A sample of candidate events for highly boosted top quarks is selected following the standard ATLAS selection for semi-leptonic ttbar events plus a requirement that the invariant mass of the reconstructed ttbar pair is greater than 700 GeV. Event displays are presented for the most promising candidates, as well as quantitative results for observables designed to isolate a boosted top quark signal.

  17. Telekommunikatsiooni & arvutitootjate TOP

    Index Scriptorium Estoniae

    2006-01-01

    Telekommunikatsiooni TOP 30. Tabelid. Vt. samas: Indrek Kald. Elisa ka tänavu esikohal; Väike Tele2 võidab paindlikkusest; Kernel läks üle piiri. Diagrammid. Arvutifirmade TOP 100. Tabelid. Vt. samas: Enn Heinsoo. Esikoha tõi kontori müük; Proeksperdil suund välisturgudele;¡ Ida-Eesti turg arenevale firmale kitsas. Diagrammid. Nimekiri: Omanikud

  18. TOP2017 Experimental summary

    CERN Document Server

    Giammanco, Andrea

    2017-01-01

    Thanks to the unprecedentedly fast accumulation of high-energy data at the LHC during the ongoing Run~2, most of the traditional top-quark analyses are experiencing the luxury of having to worry about how to punch through the ``Systematics Wall'', and think about new ways to maximize the utility of their data. New processes involving top quarks are being studied for the first time, and the good old pair-production processes are being explored in unusual settings, such as collisions involving heavy ions, or ``reference data'' collected by the LHC at relatively low centre-of-mass energy. The TOP2017 conference featured 37 talks delivered by experimental physicists, including seven in the ``Young Scientists Forum'' where young colleagues were given the opportunity to elaborate more deeply than usual on their own work. As it is impossible to do justice to all the experimental resu...

  19. Top-ophilia

    Energy Technology Data Exchange (ETDEWEB)

    Quigg, Chris; /Fermilab

    2008-01-01

    Almost from the moment in June 1977 when the discovery of the Upsilon resonance revealed the existence of what we now call the bottom quark, physicists began searching for its partner. Through the years, as we established the electric charge and weak isospin of the b-quark, and detected the virtual influence of its mate, it became clear that the top quark must exist. Exactly at what mass, we couldn't say, but we knew just how top events would look. We also knew that top events would be rare--if the Tevatron could make them at all--and that picking out the events would pose a real challenge for the experimenters and their detectors.

  20. MHD Integrated Topping Cycle Project

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-01

    The overall objective of the project is to design and construct prototypical hardware for an integrated MHD topping cycle, and conduct long duration proof-of-concept tests of integrated system at the US DOE Component Development and Integration Facility in Butte, Montana. The results of the long duration tests will augment the existing engineering design data base on MHD power train reliability, availability, maintainability, and performance, and will serve as a basis for scaling up the topping cycle design to the next level of development, an early commercial scale power plant retrofit. The components of the MHD power train to be designed, fabricated, and tested include: A slagging coal combustor with a rated capacity of 50 MW thermal input, capable of operation with an Eastern (Illinois {number sign}6) or Western (Montana Rosebud) coal, a segmented supersonic nozzle, a supersonic MHD channel capable of generating at least 1.5 MW of electrical power, a segmented supersonic diffuser section to interface the channel with existing facility quench and exhaust systems, a complete set of current control circuits for local diagonal current control along the channel, and a set of current consolidation circuits to interface the channel with the existing facility inverter.

  1. TOP LINAC design

    International Nuclear Information System (INIS)

    Picardi, L.; Ronsivalle, C.; Vignati, A.

    1997-11-01

    The report describes a linear accelerator for protons named TOP LINAC designed for the TOP (Terapia Oncologica con Protoni, Oncological Protontherapy) project launched by the Italian National Institute of Health (Istituto Superiore di Sanita', ISS) to explore in collaboration with the biggest Oncological Hospital in Rome (Istituto Regina Elena, IRE) the potentialities of the therapy with accelerated protons and establish guide lines for the application of this new type of radiotherapy in comparison with the more traditional electron and x-rays radiotherapy. The concept of a compact accelerator for protontherapy applications bore within the Italian Hadrontherapy Collaboration (TERA Collaboration) with the aim to diffuse the protontherapy on the National territory. The ISS program plans to use the TOP linac proton beam also for production of PET (Positron Emission Tomography) radioisotopes and radiobiology studies. Official agreements are in course between ISS and ENEA which provides its experience in the industrial and medical accelerators for the design and the construction of the TOP linac. The accelerator that will be the first 3 GHz proton linac in the world, will be composed of a 428.3 MHz 7 Me V RFQ + DTL injector followed by a 7-65 Me V section of a 3 GHz SCDTL structure and a 65 - 200 Me V variable energy SCL 3 GHz structure. In particular the SCDTL section uses a highly innovative accelerating structure patented by ENEA. In this report the clinical and physical requests are discussed and a preliminary design of the whole machine is given

  2. Top emitting white OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Freitag, Patricia; Luessem, Bjoern; Leo, Karl [Technische Universitaet Dresden, Institut fuer Angewandte Photophysik, George-Baehr-Strasse 1, 01069 Dresden (Germany)

    2009-07-01

    Top emitting organic light emitting diodes (TOLEDs) provide a number of interesting opportunities for new applications, such as the opportunity to fabricate ITO-free devices by using opaque substrates. This makes it possible to manufacture low cost OLEDs for signage and lighting applications. A general top emitting device consists of highly reflecting metal contacts as anode and semitransparent cathode, the latter one for better outcouling reasons. In between several organic materials are deposited as charge transporting, blocking, and emission layers. Here, we show a top emitting white organic light emitting diode with silver electrodes arranged in a p-i-n structure with p- and n-doped charge transport layers. The centrical emission layer consists of two phosphorescent (red and green) and one fluorescent (blue) emitter systems separated by an ambipolar interlayer to avoid mutual exciton quenching. By adding an additional dielectric capping layer on top of the device stack, we achieve a reduction of the strong microcavity effects which appear due to the high reflection of both metal electrodes. Therefore, the outcoupled light shows broad and nearly angle-independent emission spectra, which is essential for white light emitting diodes.

  3. Top quark theory

    Indian Academy of Sciences (India)

    2012-10-04

    Oct 4, 2012 ... The theoretical aspects of a number of top quark properties such as ... to the quadratic divergences of the Higgs self-energy, while yet, ..... given in the literature, each with the aim of recovering a well-behaved expansion in αs.

  4. Top quark properties

    Indian Academy of Sciences (India)

    eter for the tests of the electroweak theory, since radiative corrections to many ... The uncertainty due to jet energy scale (JES) is the dominating systematic .... In the Standard Model, the charge of the top quark is predicted to be that of a normal up- ..... non-negative and f+ + f0 < 1, and the star marks the expectation from the ...

  5. Anomalous top magnetic couplings

    Indian Academy of Sciences (India)

    2012-11-09

    Nov 9, 2012 ... Corresponding author. E-mail: remartinezm@unal.edu.co. Abstract. The real and imaginary parts of the one-loop electroweak contributions to the left and right tensorial anomalous couplings of the tbW vertex in the Standard Model (SM) are computed. Keywords. Top; anomalous. PACS Nos 14.65.Ha; 12.15 ...

  6. CPT analysis with top physics

    Energy Technology Data Exchange (ETDEWEB)

    Cembranos, Jose A. R., E-mail: cembra@fis.ucm.es [Universidad Complutense de Madrid, Departamento de Fisica Teorica I (Spain)

    2013-03-15

    We discuss the possibility of observing CPT violation from top anti-top production in hadronic colliders. We study a general approach by analyzing constraints on the mass difference between the top and anti-top quarks. We present current bounds from Tevatron data, and comment on the prospects for improving these bounds at the LHC and the ILC.

  7. Top Quark Properties at Tevatron

    Energy Technology Data Exchange (ETDEWEB)

    Lysák, Roman [Prague, Inst. Phys.

    2017-11-27

    The latest CDF and D0 experiment measurements of the top quark properties except the top quark mass are presented. The final combination of the CDF and D0 forward-backward asymmetry measurements is shown together with the D0 measurements of the inclusive top quark pair cross-section as well as the top quark polarization.

  8. Landfill Top Covers

    DEFF Research Database (Denmark)

    Scheutz, Charlotte; Kjeldsen, Peter

    2011-01-01

    The purpose of the final cover of a landfill is to contain the waste and to provide for a physical separation between the waste and the environment for protection of public health. Most landfill covers are designed with the primary goal to reduce or prevent infiltration of precipitation...... into the landfill in order to minimize leachate generation. In addition the cover also has to control the release of gases produced in the landfill so the gas can be ventilated, collected and utilized, or oxidized in situ. The landfill cover should also minimize erosion and support vegetation. Finally the cover...... is landscaped in order to fit into the surrounding area/environment or meet specific plans for the final use of the landfill. To fulfill the above listed requirements landfill covers are often multicomponent systems which are placed directly on top of the waste. The top cover may be placed immediately after...

  9. Computing Z-top

    International Nuclear Information System (INIS)

    Kashani-Poor, A.K.

    2014-01-01

    The topological string presents an arena in which many features of string theory proper, such as the interplay between world-sheet and target space descriptions or open-closed duality, can be distilled into computational techniques which yield results beyond perturbation theory. In this thesis, I will summarize my research activity in this area. The presentation is organized around computations of the topological string partition function Z-top based on various perspectives on the topological string. (author)

  10. Top of the list

    International Nuclear Information System (INIS)

    Cameron, A.; Vries, E. de

    2006-01-01

    In this article the authors look at how the major turbine suppliers fared in the year 2005, and look forward to 2006 which could be the best ever for the wind industry. The world wind turbine market continues to be dominated by ten major companies, who together account for almost 100% of the total global market. Although there are some new companies on the horizon it is the ten major companies that the authors concentrate on, in particular the top three, Vestas, Gamesa and Enercon who between them control 66% of the market. They give their overall report on business in 2005 and give their predictions for 2006. By far the leading wind turbine supplier is the Danish Company Vestas, accounting for over 30% of the global market. However all of the top ten companies report a successful year and all are expecting an even better 2006. This paper also reports on potential newcomers to the industry, one of these is California-based Clipper Windpower which commenced manufacturing the 2.5 MW Liberty turbine in Iowa. Chinese manufacturer Goldwind is also looking to enter the market having acquired a licence to produce the Vensys 1.2 MW turbine. It may well be that changes are on the way, there will be jockeying for position at the top and newcomers will want to make an impression on the market

  11. Solar thermal energy receiver

    Science.gov (United States)

    Baker, Karl W. (Inventor); Dustin, Miles O. (Inventor)

    1992-01-01

    A plurality of heat pipes in a shell receive concentrated solar energy and transfer the energy to a heat activated system. To provide for even distribution of the energy despite uneven impingement of solar energy on the heat pipes, absence of solar energy at times, or failure of one or more of the heat pipes, energy storage means are disposed on the heat pipes which extend through a heat pipe thermal coupling means into the heat activated device. To enhance energy transfer to the heat activated device, the heat pipe coupling cavity means may be provided with extensions into the device. For use with a Stirling engine having passages for working gas, heat transfer members may be positioned to contact the gas and the heat pipes. The shell may be divided into sections by transverse walls. To prevent cavity working fluid from collecting in the extensions, a porous body is positioned in the cavity.

  12. Top quark measurements at ATLAS

    CERN Document Server

    Grancagnolo, Sergio; The ATLAS collaboration

    2017-01-01

    The top quark is the heaviest known fundamental particle. As it is the only quark that decays before it hadronizes, this gives us the unique opportunity to probe the properties of bare quarks at the Large Hadron Collider. This talk will present highlights of a few recent precision measurements by the ATLAS Collaboration of the top quark using 13 TeV and 8 TeV collision data: top-quark pair and single top production cross sections including differential distributions will be presented alongside top quark properties measurements. These measurements, including results using boosted top quarks, probe our understanding of top quark production in the TeV regime. Measurements of the top quark mass and searches for rare top quark decays are also presented.

  13. Top quark measurements at ATLAS

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00041686; The ATLAS collaboration

    2017-01-01

    The top quark is the heaviest known fundamental particle. As it is the only quark that decays before it hadronizes, it allows us to probe the properties of bare quarks at the Large Hadron Collider. Highlights of a few recent precision measurements by the ATLAS Collaboration of the top quark using 13 TeV and 8 TeV collision data will be presented: top-quark pair and single top production cross sections including differential distributions will be presented alongside measurements of top-quark properties, including results using boosted top quarks, probe our understanding of top-quark production in the TeV regime. Measurements of the top-quark mass and searches for rare top quark decays are also presented.

  14. Naisjuhtidega ettevõtete TOP 100

    Index Scriptorium Estoniae

    2004-01-01

    Naisjuhtidega ettevõtete TOP 100. Käibe TOP 20. Käibe kasvu TOP 20. Kasumi TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Riigi- ja kohaliku omavalitsuse asutuste naisjuhtide TOP 25. Riigi- ja kohaliku omavalitsuse asutuste eelarve TOP 25. Riigi- ja kohaliku omavalitsuse asutuste töötajate arvu TOP 25. Riigi- ja kohaliku omavalitsuse asutuste naisjuhtide palga TOP 25

  15. Study of top and anti-top mass difference

    CERN Document Server

    Leedumrongwatthanakun, Saroch

    2013-01-01

    The invariance of the standard model under CPT transformations leads to the equality of particle and antiparticle masses. The recent measurements performed by the CMS experiment on the top anti-top mass difference are a test of such symmetry. In this work non-perturbative QCD effects, which may eventually lead to an apparent difference in the mass of a top and anti-top quark, are studied.

  16. Tekstiilitööstuse TOP 47

    Index Scriptorium Estoniae

    2005-01-01

    Tekstiilitööstuse TOP 47; Käibe TOP 35; Kasumi TOP 35; Käibe kasvu TOP 20; Kasumi kasvu TOP 20; Rentaabluse TOP 20; Varade tootlikkuse TOP 20; Tekstiilitööstuse TOP-i firmade üld- ja finantsandmed

  17. Rõivatööstuse TOP 50

    Index Scriptorium Estoniae

    2005-01-01

    Rõivatööstuse TOP 50; Käibe TOP 35; Kasumi TOP 35; Käibe kasvu TOP 20; Kasumi kasvu TOP 20; Rentaabluse TOP 20; Omakapitali tootlikkuse TOP 20; Rõivatööstuse TOP-i firmade üld- ja finantsandmed

  18. Eesti Ettevõtete TOP 100

    Index Scriptorium Estoniae

    2002-01-01

    TOP 100. Käibe TOP 500. Käibe kasvu TOP 100. Kasumi TOP 100. Kasumi kasvu TOP 100. Rentaabluse TOP 100. Omakapitali tootlikkuse TOP 100. Eesti edukamate ettevõtete üldandmed. Eesti edukamate ettevõtete finantsnäitajad. Valdkonna ja maakonna TOP-ide edukamate ettevõtete finantsnäitajad

  19. Treasury Offset Program (TOP) MI

    Data.gov (United States)

    Social Security Administration — The TOP MI helps OPSOS coordinate TOP case processing in the regions. The MI also helped communicate our progress and findings to BFQM and ORDP, as well as the ACOSS.

  20. Top Quark Physics with CMS

    CERN Multimedia

    CERN. Geneva

    2011-01-01

    Higgs mechanism. There are various hints at deviations from the Standard Model expectation which have been observed recently by Tevatron experiments in top final states. Several signatures of new physics accessible at the LHC either suffer from top-quark production as a significant background or contain top quarks themselves. In this talk, we present results on top quark physics obtained from the first LHC data collected by the CMS experiment.They include measurements of the top pair production cross section in various channels and their combination, measurements of the top quark mass, the single top cross section, a search for new particles decaying into top pairs, and a first look at the charge asymmetry.

  1. Wear Analysis of Top Piston Ring to Reduce Top Ring Reversal Bore Wear

    Directory of Open Access Journals (Sweden)

    P. Ilanthirayan

    2017-12-01

    Full Text Available The piston rings are the most important part in engine which controls the lubricating oil consumption and blowby of the gases. The lubricating film of oil is provided to seal of gases towards crankcase and also to give smooth friction free translatory motion between rings and liner. Of the three rings present top ring is more crucial as it does the main work of restricting gases downwards the crankcase. Boundary lubrication is present at the Top dead centre (TDC and Bottom dead centre (BDC of the liner surface. In addition to this, top ring is exposed to high temperature gases which makes the oil present near the top ring to get evaporated and decreasing its viscosity, making metal-metal contact most of the time. Due to this at TDC, excess wear happens on the liner which is termed as Top ring reversal bore wear. The wear rate depends upon many parameters such as lubrication condition, viscosity index, contact type, normal forces acting on ring, geometry of ring face, surface roughness, material property. The present work explores the wear depth for different geometries of barrel ring using Finite Element model with the help of Archard wear law and the same is validated through experimentation. The study reveals that Asymmetric barrel rings have less contact pressure which in turn reduces the wear at Top dead centre.

  2. Angular correlations in top quark decays in standard model extensions

    International Nuclear Information System (INIS)

    Batebi, S.; Etesami, S. M.; Mohammadi-Najafabadi, M.

    2011-01-01

    The CMS Collaboration at the CERN LHC has searched for the t-channel single top quark production using the spin correlation of the t-channel. The signal extraction and cross section measurement rely on the angular distribution of the charged lepton in the top quark decays, the angle between the charged lepton momentum and top spin in the top rest frame. The behavior of the angular distribution is a distinct slope for the t-channel single top (signal) while it is flat for the backgrounds. In this Brief Report, we investigate the contributions which this spin correlation may receive from a two-Higgs doublet model, a top-color assisted technicolor (TC2) and the noncommutative extension of the standard model.

  3. Top production at hadron colliders

    Indian Academy of Sciences (India)

    New results on top quark production are presented from four hadron collider experiments: CDF and D0 at the Tevatron, and ATLAS and CMS at the LHC. Cross-sections for single top and top pair production are discussed, as well as results on the top–antitop production asymmetry and searches for new physics including ...

  4. Single top t-channel

    CERN Document Server

    Faltermann, Nils

    2017-01-01

    The production of single top quarks allows to study the interplay of top quark physics and the electroweak sector of the standard model. Deviations from predictions can be a hint for physics beyond the standard model. The t-channel is the dominant production mode for single top quarks at the LHC. This talk presents the latest measurements from the ATLAS and CMS collaborations.

  5. Forward Top Physics at LHCb

    CERN Multimedia

    CERN. Geneva

    2018-01-01

    The first Run 2 measurement of top pair production in the dilepton channel at 13 TeV will be presented, along with previous Run 1 measurements in final states accessible to both single top and top pair production. Heavy flavour tagging strategies at LHCb will also be discussed.

  6. The top ten.

    Science.gov (United States)

    Davis, C

    1985-10-01

    3 lists were compiled to answer the question of what countries have experienced the most population growth from World War II to the present. The 1st list includes the 10 countries which accounted for the largest gain in world population. The 2nd list shows the 10 countries with the highest growth rates of the 150 or so most populous countries in the world. The last list also shows countries ranked by growth rate but is limited to those with a current population of at least 10 million. To deal with the fact that some countries did not exist at 1 of the reference points, a set of estimates for 1940 provided a convenient starting point. China and India headed the list of countries ranked by absolute gains. They contributed half again as much growth as the next 8 nations combined. Altogether Asia, home to almost 60% of the world's population, captured 5 of the top 10 slots. The US and the USSR are the only developed countries on the list. The Soviet Union also presents the 1st case on the list of a country with a lower ranking in population gain (6th) than in absolute size in 1985 (3rd). Many of the population giants of 1940 (Japan, Great Britain, Germany, France, and Italy) are not on the list. Despite large base populations, their growth has been slow in the intervening years. All of the countries with the highest growth rates experienced over 3% annual average growth during the last 45 years: Kuwait, United Arab Emirates, Libya, Venezuela, Costa Rica, Kenya, Ivory Coast, Mexico, Honduras, and Syria. The influence of immigration is much in evidence in this list and explains otherwise unachievable rates of growth. The top 4 countries in annual rates of growth are all oil exporters. The top 3 countries in the 3rd list -- Venezuela, Kenya, and Mexico -- are carried over from the 2nd list, sharing the characteristics of rapid population growth and substantial base populations. The geographic mix of this list is notable. Asia, Africa, and Latin America each have at least

  7. Top quark physics

    International Nuclear Information System (INIS)

    Menzione, A.

    1995-10-01

    Most of the material presented in this report, comes from contributions to the parallel session PL20 of this conference. We summarise the experimental results of direct production of Top quarks, coming from the CDF and C0 Collaborations at Fermilab, and compare these results to what one expects within current theoretical understanding. Particular attention is given to new results such as all hadronic modes of t bar t decay. As far as the mass is concerned, a comparison is made with precision measurements of related quantities, coming from LEP and other experiments. An attempt is made to look at the medium-term future and understand which variables and with what accuracy one can measure them with increased integrated luminosity

  8. Top quark pair production and top quark properties at CDF

    Energy Technology Data Exchange (ETDEWEB)

    Moon, Chang-Seong [INFN, Pisa

    2016-06-02

    We present the most recent measurements of top quark pairs production and top quark properties in proton-antiproton collisions with center-of-mass energy of 1.96 TeV using CDF II detector at the Tevatron. The combination of top pair production cross section measurements and the direct measurement of top quark width are reported. The test of Standard Model predictions for top quark decaying into $b$-quarks, performed by measuring the ratio $R$ between the top quark branching fraction to $b$-quark and the branching fraction to any type of down quark is shown. The extraction of the CKM matrix element $|V_{tb}|$ from the ratio $R$ is discussed. We also present the latest measurements on the forward-backward asymmetry ($A_{FB}$) in top anti-top quark production. With the full CDF Run II data set, the measurements are performed in top anti-top decaying to final states that contain one or two charged leptons (electrons or muons). In addition, we combine the results of the leptonic forward-backward asymmetry in $t\\bar t$ system between the two final states. All the results show deviations from the next-to-leading order (NLO) standard model (SM) calculation.

  9. Toitlustusettevõtete TOP 30 aastal 2002

    Index Scriptorium Estoniae

    2003-01-01

    Toitlustusettevõtete TOP 30 aastal 2002. Käibe TOP 30. Kasumi TOP 30. Käibe kasvu TOP 30. Kasumi kasvu TOP 30. Rentaabluse TOP 30. Omakapitali tootlikkuse TOP 30. Toitlustusettevõtete üldandmed. Toitlustusettevõtete finantsandmed

  10. Hiiumaa ettevõtete TOP 50

    Index Scriptorium Estoniae

    2005-01-01

    Hiiumaa ettevõtete TOP 50; Käibe TOP 35; Kasumi TOP 35; Hiiumaa ettevõtete üld- ja finantsandmed; Käibe kasvu TOP 20; Kasumi kasvu TOP 20; Rentaabluse TOP 20; Omakapitali tootlikkuse TOP 20. Vt samas: Teeli Remmalg: Hiiumaal jätkub plastitööstuse võidumarss

  11. The search for the top quark

    International Nuclear Information System (INIS)

    Barbaro-Galtieri, A.

    1989-03-01

    This paper discusses the following topics: top search in the near future, general remarks, top search at HERA, searching for the top quarks at the Z 0 machines, finding the top at Lep II, top search in UA2, top search in UA1, and top search at CDF. 58 refs., 38 figs

  12. Toiduainetööstuste TOP 100

    Index Scriptorium Estoniae

    2006-01-01

    Toiduainetööstuse TOP. Vt. samas: Käibe TOP 10; Käibekasvu TOP 10; Kasumi TOP 10; Kasumi kasvu TOP 10; Rentaabluse TOP 10; Omakapitali tootlikkuse TOP 10; Toiduainetööstuse üld- ja finantsandmed

  13. Online-kaubanduse TOP aastal 2003

    Index Scriptorium Estoniae

    2004-01-01

    Online-kaubanduse TOP aastal 2003. Käibe TOP 5. Käibe kasvu TOP 5. Rentaabluse TOP 5. Kasumi TOP 5. Kasumi kasvu TOP 5. Omakapitali tootlikkuse TOP 5. Lisa: TOPi koostamise metoodika. Online-kaubanduse firmade üldandmed. Online kaubanduse firmade finantsandmed

  14. TopView - ATLAS top physics analysis package

    CERN Document Server

    Shibata, A

    2007-01-01

    TopView is a common analysis package which is widely used in the ATLAS top physics working group. The package is fully based on the official ATLAS software Athena and EventView and playing a central role in the collaborative analysis model. It is a functional package which accounts for a broad range issues in implementing physics analysis. As well as being a modular framework suitable as a common workplace for collaborators, TopView implements numerous analysis tools including a complete top-antitop reconstruction and single top reconstruction. The package is currently used to produce common ntuple from Monte Carlo production and future use cases are under rapid development. In this paper, the design and ideas behind TopView and the performance of the analyses implemented in the package are presented with detailed documentation of the contents and instruction for using the package.

  15. Computer networking a top-down approach

    CERN Document Server

    Kurose, James

    2017-01-01

    Unique among computer networking texts, the Seventh Edition of the popular Computer Networking: A Top Down Approach builds on the author’s long tradition of teaching this complex subject through a layered approach in a “top-down manner.” The text works its way from the application layer down toward the physical layer, motivating readers by exposing them to important concepts early in their study of networking. Focusing on the Internet and the fundamentally important issues of networking, this text provides an excellent foundation for readers interested in computer science and electrical engineering, without requiring extensive knowledge of programming or mathematics. The Seventh Edition has been updated to reflect the most important and exciting recent advances in networking.

  16. Receiver Test Selection Criteria

    Science.gov (United States)

    2015-03-12

    The DOT requests that GPS manufacturers submit receivers for test in the following TWG categories: - Aviation (non-certified), cellular, general location/navigation, high precision, timing, networks, and space-based receivers - Each receiver should b...

  17. Naisjuhtidega ettevõtete TOP 70

    Index Scriptorium Estoniae

    2003-01-01

    Naisjuhtidega ettevõtete TOP 70. Käibe TOP 30. Käibe kasvu TOP 30. Kasumi TOP 30. Kasumi kasvu TOP 30. Rentaabluse TOP 30. Omakapitali tootlikkuse TOP 30. Nais- ja meesjuhtidega ettevõtted 2001. aasta 500 edukama ettevõtte hulgas. Naistegevjuhtidega firmade TOP 2001 ja 2002. Riigi- ja kohaliku omavalitsuse asutuste naisjuhtide TOP 20. Riigi- ja kohaliku omavalitsuse asutuste eelarve TOP 20. Riigi- ja kohaliku omavalitsuse asutuste töötajate arvu TOP 20. Naistegevjuhtidega firmade osakaal 2001. aastal. Riigi- ja kohaliku omavalitsuse asutuste naisjuhtide aastapalga TOP 20. Kommenteerib Tiina Raitviir.

  18. Solar powered Stirling engine

    Energy Technology Data Exchange (ETDEWEB)

    Meijer, R.J.

    1987-11-24

    In a solar dish module which comprises a dish which receives incident solar rays and reflects them to a focus at which is located the combination of a receiver and a heat engine organized and arranged so that the heat energy of the reflected solar rays collected at the receiver powers the engine, and wherein the receiver and heat engine are supported from the dish by a framework, the improvement is described which comprises journal means for journaling at least the engine on the framework to maintain certain predetermined spatial orientation for the engine in relation to the direction of gravity irrespective of spatial orientation of the dish.

  19. Financial top 100

    International Nuclear Information System (INIS)

    Jaremko, G.

    1999-01-01

    The way in which the oil industry has rebounded from a difficult financial year was discussed. In 1998, oil prices fell by about 30 per cent from 1997 prices to average US$14.40. In the second quarter of 1999, the rebounding international markets raised oil prices by about one-third to an average US$17.60. Recent surveys have shown that the oil and gas industry will experience major changes in the decade ahead. It was forecasted that in 25 years, total Canadian oil production could near three million barrels per day, an increase of 36 per cent from today's 2.2 million. However, as conventional reserves are running out, production of conventional oil is expected to be diminished by about two-thirds. Naturally-occurring, light refinery-ready oil is forecasted to come mostly from the east coast, whereas western output will be dominated by oil sands. Natural gas will continue to be a huge growth opportunity in the west because of new pipeline expansions and exports to the United States. This paper presented a list of Canada's financial top 100 oil and gas companies which emerged with the best endurance. The list included statistics from 1997 and 1998 for gross revenues, total assets, net income, cash/operating activities, capital expenditures, closing share prices (with percentage change), and market capitalization. 1 fig., 1 tab

  20. Our top priority

    CERN Multimedia

    2012-01-01

    After three years of LHC running, we are still at the beginning of a long research programme with our flagship facility, and hopefully 4 July 2012 will go down in history as the date of one of many landmark discoveries spanning several years. CERN’s top priority for the next decade and more is the full exploitation of the LHC. With speculation about potential future facilities mounting in the light of the discovery of a new Higgs-like particle, it’s important to state that most clearly. Of course, this will rely on continued global collaboration, and it’s important that CERN engage constructively with other regions.   It is important to plan ahead, particularly since the lead times for new projects in particle physics are long, and our field is increasingly global in nature. That’s why the European particle physics community is currently engaged in updating its long-term strategy. Planning ahead allowed us to be ready technologically to build the LHC whe...

  1. Participative Design With Top Management

    DEFF Research Database (Denmark)

    Simonsen, Jesper

    2004-01-01

    meetings aimed at aligning top management with the supplier’s analysis. The article describes the MUST method’s anchoring principle and the technique of problem mapping supporting this principle. This participatory approach resulted in mutual learning processes with top management which is rarely reported...... on in the PD community. Top management participated by reviewing, challenging, and reformulating the IT designers’ central suppositions, assumptions, and hypotheses related to the causal relation between identified problems and suggested solutions....

  2. Boosted top: experimental tools overview

    CERN Document Server

    Usai, Emanuele

    2015-01-01

    An overview of tools and methods for the reconstruction of high-boost top quark decays at the LHC is given in this report. The focus is on hadronic decays, in particular an overview of the current status of top quark taggers in physics analyses is presented. The most widely used jet substructure techniques, normally used in combination with top quark taggers, are reviewed. Special techniques to treat pileup in large cone jets are described, along with a comparison of the performance of several boosted top quark reconstruction techniques.

  3. Could stops lighten the top?

    International Nuclear Information System (INIS)

    Bilal, A.; Ellis, J.; Fogli, G.L.

    1990-01-01

    The analysis of the presently available electroweak data including radiative corrections in the standard model suggests that the top quark weighs more than the Z 0 . We examine whether squark loops in the minimal supersymmetric model, particularly those involving stops (partners of the top quark), could reduce substantially the preferred range of top quark masses. Given the present lower bounds on squark masses, we find that stop effects can reduce the central value of m t by at most a few GeV, although they do make a very heavy top quark increasingly unlikely. (orig.)

  4. Service Cart For Engines

    Science.gov (United States)

    Ng, Gim Shek

    1995-01-01

    Cart supports rear-mounted air-cooled engine from Volkswagen or Porsche automobile. One person removes, repairs, tests, and reinstalls engine of car, van, or home-built airplane. Consists of framework of wood, steel, and aluminum components supported by four wheels. Engine lifted from vehicle by hydraulic jack and gently lowered onto waiting cart. Jack removed from under engine. Rear of vehicle raised just enough that engine can be rolled out from under it. Cart easily supports 200-lb engine. Also used to hold transmission. With removable sheet-metal top, cart used as portable seat.

  5. Signs of tops from highly mixed stops

    Energy Technology Data Exchange (ETDEWEB)

    Backović, Mihailo [Center for Cosmology, Particle Physics and Phenomenology - CP3,Universite Catholique de Louvain, Louvain-la-neuve (Belgium); Mariotti, Alberto [Theoretische Natuurkunde and IIHE/ELEM, Vrije Universiteit Brussel,and International Solvay Institutes, Pleinlaan 2, B-1050 Brussels (Belgium); Spannowsky, Michael [Institute for Particle Physics Phenomenology, Department of Physics,Durham University, Durham DH1 3LE (United Kingdom)

    2015-06-17

    Supersymmetric extensions of the Standard Model with highly mixed squark flavours beyond minimal flavour violation provide interesting scenarios of new physics, which have so far received limited attention. We propose a calculable realization of such scenarios in models of gauge mediation augmented with an extra interaction between the messengers and the up type squark. We compute the supersymmetric spectrum and analyze the flavour physics constraints on such models. In a simplified model approach, we show that scenarios with maximal squark flavour mixing result in interesting phenomenological signatures at the LHC. We show that the model can be probed up to masses of m{sub ũ}≲950 GeV in the single-top event topology at LHC14 with as little as 300 fb{sup −1}. The most distinctive signature of highly mixed scenarios, the same sign positive charge di-top, can be also probed to comparable squark masses at high luminosity LHC14.

  6. More Efficient Solar Thermal-Energy Receiver

    Science.gov (United States)

    Dustin, M. O.

    1987-01-01

    Thermal stresses and reradiation reduced. Improved design for solar thermal-energy receiver overcomes three major deficiencies of solar dynamic receivers described in literature. Concentrator and receiver part of solar-thermal-energy system. Receiver divided into radiation section and storage section. Concentrated solar radiation falls on boiling ends of heat pipes, which transmit heat to thermal-energy-storage medium. Receiver used in number of applications to produce thermal energy directly for use or to store thermal energy for subsequent use in heat engine.

  7. Multi-Dimensional Top-k Dominating Queries

    DEFF Research Database (Denmark)

    Yiu, Man Lung; Mamoulis, Nikos

    2009-01-01

    The top-k dominating query returns k data objects which dominate the highest number of objects in a dataset. This query is an important tool for decision support since it provides data analysts an intuitive way for finding significant objects. In addition, it combines the advantages of top......-k and skyline queries without sharing their disadvantages: (i) the output size can be controlled, (ii) no ranking functions need to be specified by users, and (iii) the result is independent of the scales at different dimensions. Despite their importance, top-k dominating queries have not received adequate...

  8. Status of the top quark: Top production cross section and top properties

    Energy Technology Data Exchange (ETDEWEB)

    Boisvert, V.; /Rochester U.

    2006-08-01

    This report describes the latest cross section and property measurements associated with the top quark at the Tevatron Run II. The largest data sample used is 760 pb{sup -1} of integrated luminosity. Due to its large mass, the top quark might be involved in the process of electroweak symmetry breaking, making it a useful probe for signs of new physics.

  9. New directions in top physics

    Energy Technology Data Exchange (ETDEWEB)

    Schell, Torben Karl

    2017-02-01

    The top quark plays an important role for many aspects of particle physics. The coupling of the Higgs boson to top quarks is a key parameter to probe electroweak symmetry breaking and is important for the evolution of the Higgs potential to high energies. In addition, many models of physics beyond the Standard Model predict heavy particles that decay to top-quark pairs. Furthermore, the unexplained hierarchy of fermion masses culminates in the large top-quark mass. In this thesis, we consider resonance searches based on top quarks in the fully hadronic final state. We employ multivariate techniques in form of boosted decision trees and add several improvements to the original HEPTopTagger algorithm. These modifications and extensions result in the new HEPTopTagger2. The achieved improvements are used to estimate the precision to which the top Yukawa coupling can be measured at a future 100 TeV proton-proton collider in the fully hadronic final state of t anti tH production. We find that at such a collider a precision measurement of the top Yukawa coupling to 1% should be possible. The statistical precision is backed up by demonstrating that in the ratio σ(t anti tH)/σ(t anti tZ) theoretical uncertainties cancel to below-percent level. Finally, we propose a Froggatt-Nielsen-type model to address the hierarchy of fermion masses in the Standard Model and determine current and projected bounds on the available parameter space.

  10. A flexible WLAN receiver

    NARCIS (Netherlands)

    Schiphorst, Roelof; Hoeksema, F.W.; Slump, Cornelis H.

    2003-01-01

    Flexible radio receivers are also called Software Defined Radios (SDRs) [1], [2]. The focus of our SDR project [3] is on designing the front end, from antenna to demodulation in bits, of a °exible, multi-standard WLAN receiver. We try to combine an instance of a (G)FSK receiver (Bluetooth) with an

  11. Mountains: top down.

    Science.gov (United States)

    Woodwell, George M

    2004-11-01

    Mountainous regions offer not only essential habitat and resources, including water, to the earth's more than 6 billion inhabitants, but also insights into how the global human habitat works, how it is being changed at the moment as global climates are disrupted, and how the disruption may lead to global biotic and economic impoverishment. At least 600 million of the earth's more than 6 billion humans dwell in mountainous regions. Such regions feed water into all the major rivers of the world whose valleys support most of the rest of us. At least half of the valley dwellers receive part or all of their water from montane sources, many from the melt water of glaciers, others from the annual snow melt. Glaciers are retreating globally as the earth warms as a result of human-caused changes in the composition of the atmosphere. Many are disappearing, a change that threatens municipal water supplies virtually globally. The warming is greatest in the higher latitudes where the largest glaciers such as those of Greenland and the Antarctic Continent have become vulnerable. The melting of ice in the northern hemisphere raises serious concerns about the continued flow of the Gulf Stream and the possibility of massive climatic changes in Scandinavia and northern Europe. Mountains are also biotic islands in the sea life, rich in endemism at the ecotype level. The systematic warming of the earth changes the environment out from under these genetically specialized strains (ecotypes) which are then maladapted and vulnerable to diseases of all types. The process is systematic impoverishment in the pattern conspicuous on mountain slopes with increasing exposure to climatic extremes. It is seen now in the increased mortality and morbidity of plants as climatic changes accumulate. The seriousness of the global climatic disruption is especially clear in any consideration of mountains. It can and must be addressed constructively despite the adamancy of the current US administration.

  12. Highly Sensitive Optical Receivers

    CERN Document Server

    Schneider, Kerstin

    2006-01-01

    Highly Sensitive Optical Receivers primarily treats the circuit design of optical receivers with external photodiodes. Continuous-mode and burst-mode receivers are compared. The monograph first summarizes the basics of III/V photodetectors, transistor and noise models, bit-error rate, sensitivity and analog circuit design, thus enabling readers to understand the circuits described in the main part of the book. In order to cover the topic comprehensively, detailed descriptions of receivers for optical data communication in general and, in particular, optical burst-mode receivers in deep-sub-µm CMOS are presented. Numerous detailed and elaborate illustrations facilitate better understanding.

  13. Solar engine system

    International Nuclear Information System (INIS)

    Tan, K.K.; Bahrom Sanugi; Chen, L.C.; Chong, K.K.; Jasmy Yunus; Kannan, K.S.; Lim, B.H.; Noriah Bidin; Omar Aliman; Sahar Salehan; Sheikh Ab Rezan Sheikh A H; Tam, C.M.; Chen, Y.T.

    2001-01-01

    This paper reports the revolutionary solar engine system in Universiti Teknologi Malaysia (UTM). The solar engine is a single cylinder stirling engine driven by solar thermal energy. A first prototype solar engine has been built and demonstrated. A new-concept non-imaging focusing heliostat and a recently invented optical receiver are used in the demonstration. Second generation of prototype solar engine is described briefly. In this paper, the solar engine system development is reported. Measurement for the first prototype engine speed, temperature and specifications are presented. The benefits and potential applications for the future solar engine system, especially for the electricity generating aspect are discussed. (Author)

  14. Top quark properties at ATLAS

    CERN Document Server

    Dilip, Jana

    2008-01-01

    The ATLAS potential for the study of the top quark properties and physics beyond the Standard Model in the top quark sector, is described. The measurements of the top quark charge, the spin and spin correlations, the Standard Model decay (t-> bW), rare top quark decays associated to flavour changing neutral currents (t-> qX with X = gluon, Z, photon) and ttbar resonances are discussed. The sensitivity of the ATLAS experiment is estimated for an expected luminosity of 1fb-1 at the LHC. The full simulation of the ATLAS detector is used. For the Standard Model measurements the expected precision is presented. For the tests of physics beyond the Standard Model, the 5 sigma discovery potential (in the presence of a signal) and the 95% Confidence Level (CL) limit (in the absence of a signal) are given.

  15. Võrumaa ettevõtete TOP 50 aastal 2003

    Index Scriptorium Estoniae

    2004-01-01

    Võrumaa ettevõtete TOP 50 aastal 2003. Käibe TOP 40. Kasumi TOP 40. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Võrumaa firmade üld- ja finantsandmed

  16. Uncovering the single top: observation of electroweak top quark production

    Energy Technology Data Exchange (ETDEWEB)

    Benitez, Jorge Armando [Michigan State Univ., East Lansing, MI (United States)

    2009-01-01

    The top quark is generally produced in quark and anti-quark pairs. However, the Standard Model also predicts the production of only one top quark which is mediated by the electroweak interaction, known as 'Single Top'. Single Top quark production is important because it provides a unique and direct way to measure the CKM matrix element Vtb, and can be used to explore physics possibilities beyond the Standard Model predictions. This dissertation presents the results of the observation of Single Top using 2.3 fb-1 of Data collected with the D0 detector at the Fermilab Tevatron collider. The analysis includes the Single Top muon+jets and electron+jets final states and employs Boosted Decision Tress as a method to separate the signal from the background. The resulting Single Top cross section measurement is: (1) σ(p$\\bar{p}$→ tb + X, tqb + X) = 3.74-0.74+0.95 pb, where the errors include both statistical and systematic uncertainties. The probability to measure a cross section at this value or higher in the absence of signal is p = 1.9 x 10-6. This corresponds to a standard deviation Gaussian equivalence of 4.6. When combining this result with two other analysis methods, the resulting cross section measurement is: (2) σ(p$\\bar{p}$ → tb + X, tqb + X) = 3.94 ± 0.88 pb, and the corresponding measurement significance is 5.0 standard deviations.

  17. Search for Top in TOTEM

    CERN Document Server

    Corrales, Alonso

    2017-01-01

    The work assigned to me during this summer (from June 19th to August 11th) was in the "Search for Top in TOTEM" project, a CMG project in collaboration with TOTEM, under the supervision of Martijn Mulders and Laurent Forthomme. The goal is to determine physical properties of the top anti top quark pair (tt) created by central exclusive processes, particularly the invariant mass. For that it is necessary to relate the measurements of the reconstructed top pair kinematics in the central detector of CMS with the detected protons in the Roman Pots of TOTEM just outside the interaction site, about 200 m from it. CMS only considers decay products from the proton collision, it does not regard the forward protons that participated in the collision. On the contrary, TOTEM does consider these protons. In this research measurements of both TOTEM and CMS were combined Figure 1 shows a diagram of the production of the top anti top pair from the interaction of the two protons. A central exclusive process occurs when the pr...

  18. Delphi Accounts Receivable Module -

    Data.gov (United States)

    Department of Transportation — Delphi accounts receivable module contains the following data elements, but are not limited to customer information, cash receipts, line of accounting details, bill...

  19. NASA systems engineering handbook

    Science.gov (United States)

    Shishko, Robert; Aster, Robert; Chamberlain, Robert G.; McDuffee, Patrick; Pieniazek, Les; Rowell, Tom; Bain, Beth; Cox, Renee I.; Mooz, Harold; Polaski, Lou

    1995-06-01

    This handbook brings the fundamental concepts and techniques of systems engineering to NASA personnel in a way that recognizes the nature of NASA systems and environment. It is intended to accompany formal NASA training courses on systems engineering and project management when appropriate, and is designed to be a top-level overview. The concepts were drawn from NASA field center handbooks, NMI's/NHB's, the work of the NASA-wide Systems Engineering Working Group and the Systems Engineering Process Improvement Task team, several non-NASA textbooks and guides, and material from independent systems engineering courses taught to NASA personnel. Five core chapters cover systems engineering fundamentals, the NASA Project Cycle, management issues in systems engineering, systems analysis and modeling, and specialty engineering integration. It is not intended as a directive.

  20. The theory of the top

    CERN Document Server

    Klein, Felix; Nagem, Raymond J; Sandri, Guido

    The Theory of the Top. Volume IV. Technical Applications of the Theory of the Top is the fourth and final volume in a series of self-contained English translations of the classic and definitive treatment of rigid body motion. Key features: * Complete and unabridged presentation with recent advances and additional notes; * Annotations by the translators provide insights into the nature of science and mathematics in the late 19th century; * Each volume interweaves theory and applications. The Theory of the Top was originally presented by Felix Klein as an 1895 lecture at Göttingen University that was broadened in scope and clarified as a result of collaboration with Arnold Sommerfeld.  Graduate students and researchers interested in theoretical and applied mechanics will find this series of books a thorough and insightful account.  Other volumes in the series include Introduction to the Kinematics and Kinetics of the Top, Development of the Theory in the Case of the Heavy Symmetric Top, and Perturbation...

  1. Kinematic top analyses at CDF

    Energy Technology Data Exchange (ETDEWEB)

    Grassmann, H.; CDF Collaboration

    1995-03-01

    We present an update of the top quark analysis using kinematic techniques in p{bar p} collisions at {radical}s = 1.8 TeV with the Collider Detector at Fermilab (CDF). We reported before on a study which used 19.3 pb{sup {minus}1} of data from the 1992--1993 collider run, but now we use a larger data sample of 67 pb{sup {minus}1}. First, we analyze the total transverse energy of the hard collision in W+{ge}3 jet events, showing the likely presence of a t{bar t} component in the event sample. Next, we compare in more detail the kinematic structure of W+ {ge}3 jet events with expectations for top pair production and with background processes, predominantly direct W+ jet production. We again find W+ {ge} 3 jet events which cannot be explained in terms of background, but show kinematic features as expected from top. These events also show evidence for beauty quarks, in agreement with expectations from top, but not compatible with expectations from backgrounds. The findings confirm the observation of top events made earlier in the data of the 1992--1993 collider run.

  2. Proceedings of the 6th international workshop on top-quark physics. TOP 2013

    International Nuclear Information System (INIS)

    Husemann, Ulrich; Mildner, Hannes; Roscher, Frank

    2014-09-01

    The 6th International Workshop on Top-Quark Physics (TOP 2013) took place in Durbach, Germany, between September 14-19, 2013. Physicists from all over the world reported on the latest theoretical and experimental results on the physics of the top quark and discussed perspectives for the research field. While the weather in Durbach didn't always keep the promise, the scientific program certainly did: the 125 participants followed 50 plenary presentations in 15 topical sessions, complemented by a poster session in picturesque Staufenberg castle, in which 20 young scientist discussed their work over tarte flambee and and a glass of wine in front of their posters. All participants could vote for the best poster and the three best posters received prizes. In two question-and-answer sessions young physicists had the opportunity to meet world experts on top-quark physics in an informal atmosphere. The excursion brought the participants to the city of Strasbourg, France, with a boat trip on the Ill river and strolls through Strasbourg's beautiful old town. The TOP 2013 conference was co-organized by Karlsruhe Institute of Technology (KIT), DESY, and the University of Hamburg. We gratefully acknowledge the financial support the conference received from the DFG, the Helmholtz Alliance ''Physics at the Terascale'', the KIT Center Elementary Particle and Astroparticle Physics and from Blue Yonder. The conference would not have been possible without many helpers. First and foremost, we would like to thank our conference secretary, Mrs. Baerbel Braeunling. We would also like to thank the technical support team for the sessions (Martin Goerner, Steffen Roecker, Frank Roscher, Eike Schlieckau, Markus Seidel, Shawn Williamson), and the staff at Hotel Vier Jahreszeiten. We also thank Britta Liebaug for the design of the poster and the web page and Kirsten Sachs for her support in publishing these proceedings. Last but not least, the German top physics

  3. Proceedings of the 6th international workshop on top-quark physics. TOP 2013

    Energy Technology Data Exchange (ETDEWEB)

    Husemann, Ulrich; Mildner, Hannes; Roscher, Frank (eds.)

    2014-09-15

    The 6th International Workshop on Top-Quark Physics (TOP 2013) took place in Durbach, Germany, between September 14-19, 2013. Physicists from all over the world reported on the latest theoretical and experimental results on the physics of the top quark and discussed perspectives for the research field. While the weather in Durbach didn't always keep the promise, the scientific program certainly did: the 125 participants followed 50 plenary presentations in 15 topical sessions, complemented by a poster session in picturesque Staufenberg castle, in which 20 young scientist discussed their work over tarte flambee and and a glass of wine in front of their posters. All participants could vote for the best poster and the three best posters received prizes. In two question-and-answer sessions young physicists had the opportunity to meet world experts on top-quark physics in an informal atmosphere. The excursion brought the participants to the city of Strasbourg, France, with a boat trip on the Ill river and strolls through Strasbourg's beautiful old town. The TOP 2013 conference was co-organized by Karlsruhe Institute of Technology (KIT), DESY, and the University of Hamburg. We gratefully acknowledge the financial support the conference received from the DFG, the Helmholtz Alliance ''Physics at the Terascale'', the KIT Center Elementary Particle and Astroparticle Physics and from Blue Yonder. The conference would not have been possible without many helpers. First and foremost, we would like to thank our conference secretary, Mrs. Baerbel Braeunling. We would also like to thank the technical support team for the sessions (Martin Goerner, Steffen Roecker, Frank Roscher, Eike Schlieckau, Markus Seidel, Shawn Williamson), and the staff at Hotel Vier Jahreszeiten. We also thank Britta Liebaug for the design of the poster and the web page and Kirsten Sachs for her support in publishing these proceedings. Last but not least, the German top physics

  4. WordPress Top Plugins

    CERN Document Server

    Corbin, Brandon

    2010-01-01

    Time flies when you're having fun. This is the right way to describe this WordPress Top Plugins book by Brandon Corbin. With real world examples and by showing you the perks of having these plugins installed on your websites, the author is all set to captivate your interest from start to end. Regardless of whether this is your first time working with WordPress, or you're a seasoned WordPress coding ninja, WordPress Top Plugins will walk you through finding and installing the best plugins for generating and sharing content, building communities and reader base, and generating real advertising r

  5. B-2 Systems Engineering Case Study

    Science.gov (United States)

    2007-01-01

    of four small circles on the top view in front of the cockpit and on the bottom view engine bay doors. This air data system has no standard pitot ...Skantze, General, Air Force, Source Selection Advisory Board Chairman Erich Smith, Vought, Test Engineer, Systems Engineer, Chief engineer Henry

  6. Solar energy receiver

    Science.gov (United States)

    Schwartz, Jacob

    1978-01-01

    An improved long-life design for solar energy receivers provides for greatly reduced thermally induced stress and permits the utilization of less expensive heat exchanger materials while maintaining receiver efficiencies in excess of 85% without undue expenditure of energy to circulate the working fluid. In one embodiment, the flow index for the receiver is first set as close as practical to a value such that the Graetz number yields the optimal heat transfer coefficient per unit of pumping energy, in this case, 6. The convective index for the receiver is then set as closely as practical to two times the flow index so as to obtain optimal efficiency per unit mass of material.

  7. Cryogenic microwave channelized receiver

    International Nuclear Information System (INIS)

    Rauscher, C.; Pond, J.M.; Tait, G.B.

    1996-01-01

    The channelized receiver being presented demonstrates the use of high temperature superconductor technology in a microwave system setting where superconductor, microwave-monolithic-integrated-circuit, and hybrid-integrated-circuit components are united in one package and cooled to liquid-nitrogen temperatures. The receiver consists of a superconducting X-band four-channel demultiplexer with 100-MHz-wide channels, four commercial monolithically integrated mixers, and four custom-designed hybrid-circuit detectors containing heterostructure ramp diodes. The composite receiver unit has been integrated into the payload of the second-phase NRL high temperature superconductor space experiment (HTSSE-II). Prior to payload assembly, the response characteristics of the receiver were measured as functions of frequency, temperature, and drive levels. The article describes the circuitry, discusses the key issues related to design and implementation, and summarizes the experimental results

  8. Alexandrite Lidar Receiver

    National Research Council Canada - National Science Library

    Wilkerson, Thomas

    2000-01-01

    ...". The chosen vendor, Orca Photonics, In. (Redmond, WA), in close collaboration with USU personnel, built a portable, computerized lidar system that not only is suitable as a receiver for a near IR alexandrite laser, but also contains an independent Nd...

  9. Receiver Gain Modulation Circuit

    Science.gov (United States)

    Jones, Hollis; Racette, Paul; Walker, David; Gu, Dazhen

    2011-01-01

    A receiver gain modulation circuit (RGMC) was developed that modulates the power gain of the output of a radiometer receiver with a test signal. As the radiometer receiver switches between calibration noise references, the test signal is mixed with the calibrated noise and thus produces an ensemble set of measurements from which ensemble statistical analysis can be used to extract statistical information about the test signal. The RGMC is an enabling technology of the ensemble detector. As a key component for achieving ensemble detection and analysis, the RGMC has broad aeronautical and space applications. The RGMC can be used to test and develop new calibration algorithms, for example, to detect gain anomalies, and/or correct for slow drifts that affect climate-quality measurements over an accelerated time scale. A generalized approach to analyzing radiometer system designs yields a mathematical treatment of noise reference measurements in calibration algorithms. By treating the measurements from the different noise references as ensemble samples of the receiver state, i.e. receiver gain, a quantitative description of the non-stationary properties of the underlying receiver fluctuations can be derived. Excellent agreement has been obtained between model calculations and radiometric measurements. The mathematical formulation is equivalent to modulating the gain of a stable receiver with an externally generated signal and is the basis for ensemble detection and analysis (EDA). The concept of generating ensemble data sets using an ensemble detector is similar to the ensemble data sets generated as part of ensemble empirical mode decomposition (EEMD) with exception of a key distinguishing factor. EEMD adds noise to the signal under study whereas EDA mixes the signal with calibrated noise. It is mixing with calibrated noise that permits the measurement of temporal-functional variability of uncertainty in the underlying process. The RGMC permits the evaluation of EDA by

  10. Climbing back to the top

    Energy Technology Data Exchange (ETDEWEB)

    Curry, Lynn

    2010-07-01

    California - the top wind producer in the US since the 1980s lost its lead in 2008 in the face of intense competition from other states. But backed by strong financial and political support from the government, California's wind energy sector is slowly making a comeback. (orig.)

  11. Kowalevski top in quantum mechanics

    International Nuclear Information System (INIS)

    Matsuyama, A.

    2013-01-01

    The quantum mechanical Kowalevski top is studied by the direct diagonalization of the Hamiltonian. The spectra show different behaviors depending on the region divided by the bifurcation sets of the classical invariant tori. Some of these spectra are nearly degenerate due to the multiplicity of the invariant tori. The Kowalevski top has several symmetries and symmetry quantum numbers can be assigned to the eigenstates. We have also carried out the semiclassical quantization of the Kowalevski top by the EBK formulation. It is found that the semiclassical spectra are close to the exact values, thus the eigenstates can be also labeled by the integer quantum numbers. The symmetries of the system are shown to have close relations with the semiclassical quantum numbers and the near-degeneracy of the spectra. -- Highlights: •Quantum spectra of the Kowalevski top are calculated. •Semiclassical quantization is carried out by the EBK formulation. •Quantum states are labeled by the semiclassical integer quantum numbers. •Multiplicity of the classical torus makes the spectra nearly degenerate. •Symmetries, quantum numbers and near-degenerate spectra are closely related

  12. Top production at hadron colliders

    Indian Academy of Sciences (India)

    mulated by the summer of 2010, the first top quark event candidates were observed and ..... Result of combined fit to data in the exclusive three-jet bin, the exclusive .... Figure 7 shows the results of a model-independent measurement of.

  13. TEMAC, Top Event Sensitivity Analysis

    International Nuclear Information System (INIS)

    Iman, R.L.; Shortencarier, M.J.

    1988-01-01

    1 - Description of program or function: TEMAC is designed to permit the user to easily estimate risk and to perform sensitivity and uncertainty analyses with a Boolean expression such as produced by the SETS computer program. SETS produces a mathematical representation of a fault tree used to model system unavailability. In the terminology of the TEMAC program, such a mathematical representation is referred to as a top event. The analysis of risk involves the estimation of the magnitude of risk, the sensitivity of risk estimates to base event probabilities and initiating event frequencies, and the quantification of the uncertainty in the risk estimates. 2 - Method of solution: Sensitivity and uncertainty analyses associated with top events involve mathematical operations on the corresponding Boolean expression for the top event, as well as repeated evaluations of the top event in a Monte Carlo fashion. TEMAC employs a general matrix approach which provides a convenient general form for Boolean expressions, is computationally efficient, and allows large problems to be analyzed. 3 - Restrictions on the complexity of the problem - Maxima of: 4000 cut sets, 500 events, 500 values in a Monte Carlo sample, 16 characters in an event name. These restrictions are implemented through the FORTRAN 77 PARAMATER statement

  14. Top mass measurement at CDF

    International Nuclear Information System (INIS)

    Rolli, S.

    1996-06-01

    We present the measurement of the top quark mass using L = 110 pb -1 data sample of pp collisions at √s = 1.8 TeV collected with the Collider Detector at Fermilab (CDF). We show the results for the different channels and discuss with some emphasis the determination of the systematic uncertainties. 7 refs., 10 figs., 5 tabs

  15. Observation of the Top Quark

    Science.gov (United States)

    Kim, S. B.

    1995-08-01

    Top quark production is observed in{bar p}p collisions at{radical}s= 1.8 TeV at the Fermilab Tevatron. The Collider Detector at Fermilab (CDF) and D{O} observe signals consistent with t{bar t} to WWb{bar b}, but inconsistent with the background prediction by 4.8{sigma} (CDF), 4.6a (D{O}). Additional evidence for the top quark Is provided by a peak in the reconstructed mass distribution. The kinematic properties of the excess events are consistent with the top quark decay. They measure the top quark mass to be 176{plus_minus}8(stat.){plus_minus}10(sys.) GeV/c{sup 2} (CDF), 199{sub -21}{sup+19}(stat.){plus_minus}22(sys.) GeV/c{sup 2} (D{O}), and the t{bar t} production cross section to be 6.8{sub -2.4}{sup+3.6}pb (CDF), 6.4{plus_minus}2.2 pb (D{O}).

  16. Tree compression with top trees

    DEFF Research Database (Denmark)

    Bille, Philip; Gørtz, Inge Li; Landau, Gad M.

    2013-01-01

    We introduce a new compression scheme for labeled trees based on top trees [3]. Our compression scheme is the first to simultaneously take advantage of internal repeats in the tree (as opposed to the classical DAG compression that only exploits rooted subtree repeats) while also supporting fast...

  17. Tree compression with top trees

    DEFF Research Database (Denmark)

    Bille, Philip; Gørtz, Inge Li; Landau, Gad M.

    2015-01-01

    We introduce a new compression scheme for labeled trees based on top trees. Our compression scheme is the first to simultaneously take advantage of internal repeats in the tree (as opposed to the classical DAG compression that only exploits rooted subtree repeats) while also supporting fast...

  18. Top Jets at the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, L.G.; Lee, S.J.; Perez, G.; Sung, I.; Virzi, J.

    2008-10-06

    We investigatethe reconstruction of high pT hadronically-decaying top quarksat the Large Hadron Collider. One of the main challenges in identifying energetictop quarks is that the decay products become increasingly collimated. This reducesthe efficacy of conventional reconstruction methods that exploit the topology of thetop quark decay chain. We focus on the cases where the decay products of the topquark are reconstructed as a single jet, a"top-jet." The most basic"top-tag" methodbased on jet mass measurement is considered in detail. To analyze the feasibility ofthe top-tagging method, both theoretical and experimental aspects of the large QCDjet background contribution are examined. Based on a factorization approach, wederive a simple analytic approximation for the shape of the QCD jet mass spectrum.We observe very good agreement with the Monte Carlo simulation. We consider high pT tt bar production in the Standard Model as an example, and show that our theoretical QCD jet mass distributions can efficiently characterize the background via sideband analyses. We show that with 25 fb-1 of data, our approach allows us to resolve top-jets with pT _> 1 TeV, from the QCD background, and about 1.5 TeV top-jets with 100 fb-1, without relying on b-tagging. To further improve the significancewe consider jet shapes (recently analyzed in 0807.0234 [hep-ph]), which resolve thesubstructure of energy flow inside cone jets. A method of measuring the top quarkpolarization by using the transverse momentum of the bottom quark is also presented.The main advantages of our approach are: (i) the mass distributions are driven byfirst principle calculations, instead of relying solely on Monte Carlo simulation; (ii) for high pT jets (pT _> 1 TeV), IR-safe jet shape variables are robust against detectorresolution effects. Our analysis can be applied to other boosted massive particlessuch as the electroweak gauge bosons and the Higgs.

  19. Measurements of Top Properties at the Tevatron

    International Nuclear Information System (INIS)

    Husemann, Ulrich; Yale U.

    2007-01-01

    The large data samples of thousands of top events collected at the Tevatron experiments CDF and D(O) allow for a variety of measurements to analyze the properties of the top quark. Guided by the question ''Is the top quark observed at the Tevatron really the top quark of the standard model,'' we present Tevatron analyses studying the top production mechanism including resonant t(bar t) production, the V -A structure of the t → Wb decay vertex, the charge of the top quark, and single-top production via flavor-changing neutral currents

  20. 'Chaos' in superregenerative receivers

    International Nuclear Information System (INIS)

    Commercon, Jean-Claude; Badard, Robert

    2005-01-01

    The superregenerative principle has been known since the early 1920s. The circuit is extremely simple and extremely sensitive. Today, superheterodyne receivers generally supplant superregenerative receivers in most applications because there are several undesirable characteristics: poor selectivity, reradiation, etc. Superregenerative receivers undergo a revival in recent papers for wireless systems, where low cost and very low power consumption are relevant: house/building meters (such as water, energy, gas counter), personal computer environment (keyboard, mouse), etc. Another drawback is the noise level which is higher than that of a well-designed superheterodyne receiver; without an antenna input signal, the output of the receiver hears in an earphone as a waterfall noise; this sound principally is the inherent input noise amplified and detected by the circuit; however, when the input noise is negligible with respect of an antenna input signal, we are faced to an other source of 'noise' self-generated by the superregenerative working. The main objective of this paper concerns this self-generated noise coming from an exponential growing followed by a re-injection process for which the final state is a function of the phase of the input signal

  1. Properties of the Top Quark

    Energy Technology Data Exchange (ETDEWEB)

    Wicke, Daniel; /Wuppertal U., Dept. Math.

    2009-08-01

    The aim of particle physics is the understanding of elementary particles and their interactions. The current theory of elementary particle physics, the Standard Model, contains twelve different types of fermions which (neglecting gravity) interact through the gauge bosons of three forces. In addition a scalar particle, the Higgs boson, is needed for theoretical consistency. These few building blocks explain all experimental results found in the context of particle physics, so far. Nevertheless, it is believed that the Standard Model is only an approximation to a more complete theory. First of all the fourth known force, gravity, has withstood all attempts to be included until now. Furthermore, the Standard Model describes several features of the elementary particles like the existence of three families of fermions or the quantisation of charges, but does not explain these properties from underlying principles. Finally, the lightness of the Higgs boson needed to explain the symmetry breaking is difficult to maintain in the presence of expected corrections from gravity at high scales. This is the so called hierarchy problem. In addition astrophysical results indicate that the universe consists only to a very small fraction of matter described by the Standard Model. Large fractions of dark energy and dark matter are needed to describe the observations. Both do not have any correspondence in the Standard Model. Also the very small asymmetry between matter and anti-matter that results in the observed universe built of matter (and not of anti-matter) cannot be explained until now. It is thus an important task of experimental particle physics to test the predictions of the Standard Model to the best possible accuracy and to search for deviations pointing to necessary extensions or modifications of our current theoretical understanding. The top quark was predicted to exist by the Standard Model as the partner of the bottom quark. It was first observed in 1995 by the

  2. Properties of the Top Quark

    International Nuclear Information System (INIS)

    Wicke, Daniel

    2009-01-01

    The aim of particle physics is the understanding of elementary particles and their interactions. The current theory of elementary particle physics, the Standard Model, contains twelve different types of fermions which (neglecting gravity) interact through the gauge bosons of three forces. In addition a scalar particle, the Higgs boson, is needed for theoretical consistency. These few building blocks explain all experimental results found in the context of particle physics, so far. Nevertheless, it is believed that the Standard Model is only an approximation to a more complete theory. First of all the fourth known force, gravity, has withstood all attempts to be included until now. Furthermore, the Standard Model describes several features of the elementary particles like the existence of three families of fermions or the quantisation of charges, but does not explain these properties from underlying principles. Finally, the lightness of the Higgs boson needed to explain the symmetry breaking is difficult to maintain in the presence of expected corrections from gravity at high scales. This is the so called hierarchy problem. In addition astrophysical results indicate that the universe consists only to a very small fraction of matter described by the Standard Model. Large fractions of dark energy and dark matter are needed to describe the observations. Both do not have any correspondence in the Standard Model. Also the very small asymmetry between matter and anti-matter that results in the observed universe built of matter (and not of anti-matter) cannot be explained until now. It is thus an important task of experimental particle physics to test the predictions of the Standard Model to the best possible accuracy and to search for deviations pointing to necessary extensions or modifications of our current theoretical understanding. The top quark was predicted to exist by the Standard Model as the partner of the bottom quark. It was first observed in 1995 by the

  3. Toiduainetööstuse TOP 95 aastal 2003

    Index Scriptorium Estoniae

    2004-01-01

    Toiduainetööstuse TOP 95; Kasumi TOP 40; Käibe TOP 40; Kasumi kasvu TOP 30; Rentaabluse TOP 30; Alkoholitootjate TOP; Pagarite TOP; Käibe kasvu TOP 30; Omakapitali tootlikkuse TOP 30; Toiduainetööstuste üld- ja finantsandmed

  4. Top quark production at the Tevatron

    Energy Technology Data Exchange (ETDEWEB)

    Varnes, Erich W.; /Arizona U.

    2010-09-01

    The Fermilab Tevatron has, until recently, been the only accelerator with sufficient energy to produce top quarks. The CDF and D0 experiments have collected large samples of top quarks. We report on recent top quark production measurements of the single top and t{bar t} production cross sections, as well as studies of the t{bar t} invariant mass distribution and a search for highly boosted top quarks.

  5. Solar thermal central receivers

    International Nuclear Information System (INIS)

    Vant-Hull, L.L.

    1993-01-01

    Market issues, environmental impact, and technology issues related to the Solar Central Receiver concept are addressed. The rationale for selection of the preferred configuration and working fluid are presented as the result of a joint utility-industry analysis. A $30 million conversion of Solar One to an external molten salt receiver would provide the intermediate step to a commercial demonstration plant. The first plant in this series could produce electricity at 11.2 cents/kWhr and the seventh at 8.2 cents/kWhr, completely competitive with projected costs of new utility plants in 1992

  6. Wideband CMOS receivers

    CERN Document Server

    Oliveira, Luis

    2015-01-01

    This book demonstrates how to design a wideband receiver operating in current mode, in which the noise and non-linearity are reduced, implemented in a low cost single chip, using standard CMOS technology.  The authors present a solution to remove the transimpedance amplifier (TIA) block and connect directly the mixer’s output to a passive second-order continuous-time Σ∆ analog to digital converter (ADC), which operates in current-mode. These techniques enable the reduction of area, power consumption, and cost in modern CMOS receivers.

  7. Thermal design of top shield

    International Nuclear Information System (INIS)

    Raghupathy, S.; Velusamy, K.; Parthasarathy, U.; Ghosh, D.; Selvaraj, P.; Chellapandi, P.; Chetal, S.C.

    2005-01-01

    Full text of publication follows: Prototype Fast Breeder Reactor (PFBR) is a 500 MWe, sodium cooled, pool type fast reactor. The top shield forms the top cover for the main vessel (MV) and includes roof slab (RS), large rotatable plug (LRP), small rotatable plug (SRP) and control Plug (CP). RS, LRP and SRP are box type structures consisting of top and bottom plates stiffened by radial stiffeners and vertical penetration shells. TS is exposed to argon cover gas provided above sodium pool on the bottom side and reactor containment building air at the top. Heat transfer takes place through the argon cover gas to the bottom plate of TS. Annular gaps are formed between the components supported on TS and the component penetrations through which cellular convection takes place. A single thermal shield provided below TS reduces the heat flux to the bottom plate to 1.15 kW/m 2 . The MV (SS 316 LN) is welded to RS (carbon steel A48 P2) through a dissimilar metal weld. A step in RS and an anti convection barrier (ACB) outside RS are provided to limit the temperature at the MV-RS junction. The MV is surrounded by safety vessel (SV) and reactor vault made of concrete. Thermal insulation is provided outside SV to limit the heat transfer to the reactor vault. The design requirements of TS are to maintain the operating temperature at 383-393 K, limit the temperature difference (ΔT) across the height of TS to 20 / 100 K under normal operation/loss of cooling, provide minimum annular gap size at the component penetrations, provide a nearly linear temperature gradient in the CP portion within the height of TS, maintain the temperature of top plate of CP > 383 K, limit the ΔT across the top plate of CP to 2 K, limit the temperature near the inflatable / backup seal to 393 K, limit the temperature at the MV-RS junction and the heat flux to the reactor vault. The total heat transferred to TS is estimated to be 210 kW. A dedicated closed loop cooling system with a total flow rate of 10

  8. Top-Down Enterprise Application Integration with Reference Models

    Directory of Open Access Journals (Sweden)

    Willem-Jan van den Heuvel

    2000-11-01

    Full Text Available For Enterprise Resource Planning (ERP systems such as SAP R/3 or IBM SanFrancisco, the tailoring of reference models for customizing the ERP systems to specific organizational contexts is an established approach. In this paper, we present a methodology that uses such reference models as a starting point for a top-down integration of enterprise applications. The re-engineered models of legacy systems are individually linked via cross-mapping specifications to the forward-engineered reference model's specification. The actual linking of reference and legacy models is done with a methodology for connecting (new business objects with (old legacy systems.

  9. Receiver gain function: the actual NMR receiver gain

    OpenAIRE

    Mo, Huaping; Harwood, John S.; Raftery, Daniel

    2010-01-01

    The observed NMR signal size depends on the receiver gain parameter. We propose a receiver gain function to characterize how much the raw FID is amplified by the receiver as a function of the receiver gain setting. Although the receiver is linear for a fixed gain setting, the actual gain of the receiver may differ from what the gain setting suggests. Nevertheless, for a given receiver, we demonstrate that the receiver gain function can be calibrated. Such a calibration enables accurate compar...

  10. Campus Projects Receiving "Earmarks."

    Science.gov (United States)

    Schonberger, Benjamin

    1991-01-01

    Specific campus projects that Congress has directed federal agencies to support this year at over 120 colleges and universities are listed. The agencies neither requested support nor sponsored merit-based competitions for the awards. In some cases, the institutions have a history of receiving special federal treatment. (MSE)

  11. Gold awards for CERN's top suppliers!

    CERN Multimedia

    2003-01-01

    CERN's awards to the LHC project's best suppliers are now into their second year. Three companies received 'Golden Hadrons' for 2003. The Golden Hadron awards were presented to the delighted representatives of the winning firms by LHC Project Leader Lyn Evans on Friday 16 May. Only three out of the LHC's four hundred suppliers were lucky enough to receive a gold award. The consortium IHI (Japan)-Linde Kryotechnik (Switzerland), the Belgian company JDL Technologies and the Japanese firm Furukawa Electric Company were rewarded not only for their technical and financial achievements but also for their compliance with contractual deadlines. The 2003 Golden Hadron winners with Lyn Evans. From left to right: Armin Senn, Thomas Voigt, Kirkor Kurtcuoglu of LINDE KRYOTECHNIK ; Tadaaki Honda, Project Leader and Motoki Yoshinaga, Associate Director of IHI Corporation ; Lyn Evans, LHC Project Leader; Shinichiro Meguro, Managing Director of FURUKAWA ELECTRIC COMPANY ; Nobuyoshi Saji, Consulting Engineer of IHI Corporatio...

  12. Nuclear reactor fuel assembly with a removably top nozzle

    International Nuclear Information System (INIS)

    Shallenberger, J.M.; Ferlan, S.J.

    1985-01-01

    The invention relates to a nuclear fuel assembly having an improved attaching structure for removably mounting the top nozzle of the fuel assembly on the upper end of a control-rod guide thimble. The attaching structure comprises an outer socket defined in a portion of the top nozzle, an inner socket extending from the upper end of the guide thimble and removably received in the outer socket for interlocking engagement therewith, and an elongate locking member adapted to be inserted into the inner socket to maintain said interlocking engagement. Removal of the locking member from the inner socket enables the latter to be withdrawn from the outer socket, thereby enabling the top nozzle to be removed from the guide thimble

  13. The Top Companies You Want to Work for Most and Why.

    Science.gov (United States)

    Freedland, Marjorie

    1988-01-01

    Summarizes the results of the 1987 National Engineering Student Employer Preference Survey and compares them with those reported by three previous biennial surveys. Lists the top 25 employer choices in electrical, mechanical, computer science, industrial, chemical, civil and astro/aeronautical engineering. (TW)

  14. Automotive engineering partners

    Energy Technology Data Exchange (ETDEWEB)

    Liebl, Johannes; Siebenpfeiffer, Wolfgang (eds.)

    2012-05-15

    The brochure under consideration consists of contributions to the following aspects: (1) the ATZ ranking of the Top 75 of the companies providing development service; (2) Challenges and opportunities of hybrid vehicles: (3) Localization of sound sources; (4) Sectoral index engineering services.

  15. NASA Systems Engineering Handbook

    Science.gov (United States)

    Hirshorn, Steven R.; Voss, Linda D.; Bromley, Linda K.

    2017-01-01

    The update of this handbook continues the methodology of the previous revision: a top-down compatibility with higher level Agency policy and a bottom-up infusion of guidance from the NASA practitioners in the field. This approach provides the opportunity to obtain best practices from across NASA and bridge the information to the established NASA systems engineering processes and to communicate principles of good practice as well as alternative approaches rather than specify a particular way to accomplish a task. The result embodied in this handbook is a top-level implementation approach on the practice of systems engineering unique to NASA. Material used for updating this handbook has been drawn from many sources, including NPRs, Center systems engineering handbooks and processes, other Agency best practices, and external systems engineering textbooks and guides. This handbook consists of six chapters: (1) an introduction, (2) a systems engineering fundamentals discussion, (3) the NASA program project life cycles, (4) systems engineering processes to get from a concept to a design, (5) systems engineering processes to get from a design to a final product, and (6) crosscutting management processes in systems engineering. The chapters are supplemented by appendices that provide outlines, examples, and further information to illustrate topics in the chapters. The handbook makes extensive use of boxes and figures to define, refine, illustrate, and extend concepts in the chapters.

  16. Capacity Building for Engineering Education

    DEFF Research Database (Denmark)

    de Graaff, Erik; Deboer, Jennifer

    2015-01-01

    faculty leadership training workshops/courses/seminars, helping to broker the offering of these around the world. Since 2011 IIDEA has been offering diverse workshops facilitated by top engineering education leaders as stand alone or as pre- post conference activities. Engineering educators...

  17. Breaking open the set top box

    Science.gov (United States)

    Banks, David; Wiley, Anthony; Catania, Nicolas; Coles, Alastair N.; Smith, Duncan; Baynham, Simon; Deliot, Eric; Chidzey, Rod

    1998-02-01

    In this paper we describe the work being done at HP Labs Bristol in the area of home networks and gateways. This work is based on the idea of breaking open the set top box by physically separating the access network specific functions from the application specific functions. The access network specific functions reside in an access network gateway that can be shared by many end user devices. The first section of the paper present the philosophy behind this approach. The end user devices and the access network gateways must be interconnected by a high bandwidth network which can offer a bounded delay service for delay sensitive traffic. We are advocating the use of IEEE 1394 for this network, and the next section of the paper gives a brief introduction to this technology. We then describe a prototype digital video broadcasting satellite compliant gateway that we have built. This gateway could be used, for example, by a PC for receiving a data service or by a digital TV for receiving an MPEG-2 video service. A control architecture is the presented which uses a PC application to provide a web based user interface to the system. Finally, we provide details of our work on extending the reach of IEEE 1394 and its standardization status.

  18. Top quark studies at hadron colliders

    Energy Technology Data Exchange (ETDEWEB)

    Sinervo, P.K. [Univ. of Toronto, Ontario (Canada)

    1997-01-01

    The techniques used to study top quarks at hadron colliders are presented. The analyses that discovered the top quark are described, with emphasis on the techniques used to tag b quark jets in candidate events. The most recent measurements of top quark properties by the CDF and DO Collaborations are reviewed, including the top quark cross section, mass, branching fractions, and production properties. Future top quark studies at hadron colliders are discussed, and predictions for event yields and uncertainties in the measurements of top quark properties are presented.

  19. Top quark studies at hadron colliders

    International Nuclear Information System (INIS)

    Sinervo, P.K.

    1997-01-01

    The techniques used to study top quarks at hadron colliders are presented. The analyses that discovered the top quark are described, with emphasis on the techniques used to tag b quark jets in candidate events. The most recent measurements of top quark properties by the CDF and DO Collaborations are reviewed, including the top quark cross section, mass, branching fractions, and production properties. Future top quark studies at hadron colliders are discussed, and predictions for event yields and uncertainties in the measurements of top quark properties are presented

  20. Top quark studies at hadron colliders

    International Nuclear Information System (INIS)

    Sinervo, P.K.

    1996-08-01

    The techniques used to study top quarks at hadron colliders are presented. The analyses that discovered the top quark are described, with emphasis on the techniques used to tag b quark jets in candidate events. The most recent measurements of top quark properties by the CDF and D null collaborations are reviewed, including the top quark cross section, mass, branching fractions and production properties. Future top quark studies at hadron colliders are discussed, and predictions for event yields and uncertainties in the measurements of top quark properties are presented

  1. Engine piston assembly and forged piston member therefor having a cooling recess

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, B.C.; Erickson, K.L.; Green, J.A.; Nyez, D.S.

    1989-09-19

    This patent describes a forged steel piston member for reciprocating movement in an engine. It comprises: an upper portion of substantially cylindrical shape and having a central axis, a top surface, a tubular wall depending from the top surface and having a peripheral groove adapted to receive a sealing ring, a lower end surface, and an inwardly facing wall surface extending upwardly from the lower end surface. The upper portion further includes an outwardly facing wall surface spaced radially inwardly from the inwardly facing wall surface and a downwardly facing transition portion blendingly associated with the inwardly and outwardly facing wall surfaces to collectively define an annular cooling recess, the transition portion being elevational spaced a relatively short distance from the top surface; and the inwardly facing wall surface being a machined surface of revolution about the central axis integral or one-piece forging.

  2. The Top-100 Most-Cited Articles on Meningioma.

    Science.gov (United States)

    Almutairi, Othman; Albakr, Abdulrahman; Al-Habib, Amro; Ajlan, Abdulrazag

    2017-11-01

    There is an abundance of articles published on meningioma. To identify the 100 most-cited articles on meningioma and to perform a bibliometric analysis. In November 2016, we performed a title-specific search of the Scopus database using "meningioma" as our search query term without publication date restrictions. The top 100 most cited articles were obtained and reviewed. The top 100 most cited articles received a mean 198 citations per paper. Publication dates ranged from 1953 to 2013; most articles were published between 1994 and 2003, with 50 articles published during that period. NEUROSURGERY published the greatest number of top cited articles (22 of 100). The most frequent study categories were laboratorial studies (31 of 100) and natural history studies (28 of 100). Nonoperative management studies were twice as common as operative management studies in the top-cited articles. Neurosurgery as a specialty contributed to 50% of the top 100 list. The most contributing institute was the Mayo Clinic (11%); the majority of the top cited articles originated in the United States (53%). We identified the top 100 most-cited articles on meningioma that may be considered significant and impactful works, as well as the most noteworthy. In addition, we recognized the historical development and advances in meningioma research and the important contributions of various authors, specialty fields, and countries. A large proportion of the most cited articles were written by authors other than neurosurgeons, and many of these articles were published in non-neurosurgery journals. Copyright © 2017 Elsevier Inc. All rights reserved.

  3. Bibliometric analysis of the top 100 cited cardiovascular articles.

    Science.gov (United States)

    Shuaib, Waqas; Khan, Muhammad S; Shahid, Hassan; Valdes, Emilio A; Alweis, Richard

    2015-04-01

    The number of citations an article receives is an important indication of its impact and contribution to the clinical world. There is a paucity of literature concerning top article citations in cardiology. The main objective of this investigation was to bridge this gap and to provide readers a practical guide in evaluating the cardiovascular literature. Scopus Library database was searched to determine the citations of all published cardiovascular articles. One hundred two journals were included in our investigation under the Institute of Science Information Web of Science subject category "cardiology, cardiovascular, and heart." We did not apply any time or study-type restriction in our search. The top 100 cited articles were selected and analyzed by 2 independent investigators. The journal with the highest number of top 100 cited articles was Circulation with 36, followed by 28 in the European Heart Journal. A statistically significant association was found between the journal impact factor and the number of top 100 cited articles (p journals such as The Lancet (n = 4) and The New England Journal of Medicine (n = 1) contributed only 5 articles to the list despite their extremely high impact factors. In conclusion, our analysis provides an insight on the citation frequency of top cited articles published in cardiovascular medicine to help recognize the quality of the works, discoveries, and the trends steering cardiology. Copyright © 2015 Elsevier Inc. All rights reserved.

  4. Toiduainetööstuse TOP 95 aastal 2002

    Index Scriptorium Estoniae

    2003-01-01

    Toiduainetööstuse TOP 95. Käibe TOP 50. Kasumi TOP 50. Rentaabluse TOP 25. Kasumi kasvu TOP 25. Omakapitali tootlikkuse TOP 25. Käibe kasvu TOP 25. Toiduainetööstuse TOP 95 ettevõtted 2002: üldandmed ja finantsandmed

  5. Ida-Virumaa ettevõtete TOP aastal 2002

    Index Scriptorium Estoniae

    2003-01-01

    Ettevõtete TOP 55. TOP-i esikümme. Käibe TOP 40. Kasumi TOP 40. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Ida-Virumaa firmade üldandmed. Ida-Virumaa firmade finantsandmed

  6. Table-top job analysis

    Energy Technology Data Exchange (ETDEWEB)

    1994-12-01

    The purpose of this Handbook is to establish general training program guidelines for training personnel in developing training for operation, maintenance, and technical support personnel at Department of Energy (DOE) nuclear facilities. TTJA is not the only method of job analysis; however, when conducted properly TTJA can be cost effective, efficient, and self-validating, and represents an effective method of defining job requirements. The table-top job analysis is suggested in the DOE Training Accreditation Program manuals as an acceptable alternative to traditional methods of analyzing job requirements. DOE 5480-20A strongly endorses and recommends it as the preferred method for analyzing jobs for positions addressed by the Order.

  7. Top-down cellular pyramids

    Energy Technology Data Exchange (ETDEWEB)

    Wu, A Y; Rosenfeld, A

    1983-10-01

    A cellular pyramid is an exponentially tapering stack of arrays of processors (cells), where each cell is connected to its neighbors (siblings) on its own level, to a parent on the level above, and to its children on the level below. It is shown that in some situations, if information flows top-down only, from fathers to sons, then a cellular pyramid may be no faster than a one-level cellular array; but it may be possible to use simpler cells in the pyramid case. 23 references.

  8. Digital Receiver Phase Meter

    Science.gov (United States)

    Marcin, Martin; Abramovici, Alexander

    2008-01-01

    The software of a commercially available digital radio receiver has been modified to make the receiver function as a two-channel low-noise phase meter. This phase meter is a prototype in the continuing development of a phase meter for a system in which radiofrequency (RF) signals in the two channels would be outputs of a spaceborne heterodyne laser interferometer for detecting gravitational waves. The frequencies of the signals could include a common Doppler-shift component of as much as 15 MHz. The phase meter is required to measure the relative phases of the signals in the two channels at a sampling rate of 10 Hz at a root power spectral density measurements in laser metrology of moving bodies. To illustrate part of the principle of operation of the phase meter, the figure includes a simplified block diagram of a basic singlechannel digital receiver. The input RF signal is first fed to the input terminal of an analog-to-digital converter (ADC). To prevent aliasing errors in the ADC, the sampling rate must be at least twice the input signal frequency. The sampling rate of the ADC is governed by a sampling clock, which also drives a digital local oscillator (DLO), which is a direct digital frequency synthesizer. The DLO produces samples of sine and cosine signals at a programmed tuning frequency. The sine and cosine samples are mixed with (that is, multiplied by) the samples from the ADC, then low-pass filtered to obtain in-phase (I) and quadrature (Q) signal components. A digital signal processor (DSP) computes the ratio between the Q and I components, computes the phase of the RF signal (relative to that of the DLO signal) as the arctangent of this ratio, and then averages successive such phase values over a time interval specified by the user.

  9. Top quark production at the LHC

    CERN Document Server

    Gilles, Geoffrey; The ATLAS collaboration

    2018-01-01

    The top quark is the heaviest known fundamental particle. As it is the only quark that decays before it hadronizes, it gives us the unique opportunity to probe the properties of bare quarks at the Large Hadron Collider. This talk will present highlights of a few recent precision measurements of the top quark using 13 TeV and 8 TeV collision data: top-quark pair and single top production cross sections, including differential distributions and production in association with bosons, will be presented alongside top quark properties measurements. These measurements, including results using boosted top quarks, probe our understanding of top quark production in the TeV regime. Measurements of the top quark mass are also presented.

  10. Results on top-quark physics and top-quark-like signatures by CMS

    Science.gov (United States)

    Chabert, Eric; CMS Collaboration

    2017-07-01

    This report reviews the results obtained by the CMS Collaboration on top quark physics, focusing on the latest ones based on p-p collisions provided by the LHC at \\sqrt{s}=13{{TeV}} during Run II. It covers measurements of single-top, top quark pairs and associated productions as well as measurements of top quark properties. Finally several beyond the standard model searches involving top quark in the final states are presented, such as searches for supersymmetry in the third generation, heavy resonances decaying into a top quark pair, or dark matter produced in association to a single-top or a top quark pair.

  11. Top mass in ATLAS and CMS

    CERN Document Server

    Castro, A.

    2017-01-01

    Top quarks are produced copiously at the LHC, and a variety of related measurements has been made in the recent years by the two collaborations ATLAS and CMS. The most recent measurements of the top quark mass by the two collaborations are reported here. The top quark mass has been measured with a relative uncertainty smaller than 0.3pct, making the top quark the most accurately measured quark.

  12. New Physics in Single-Top Production

    CERN Document Server

    Kind, OM; The ATLAS collaboration

    2013-01-01

    In this presentation for TOP 2013 the latest results on searches of physics beyond the Standard Model using single-top signatures from CDF, CMS, D0 and ATLAS are collected. This includes searches for unknown resonances like W' or b*, measurements of the W helicity fractions and top polarisation in single-top events, as well as tests for CP violation, FCNC or anomalous weak couplings.

  13. Top technology at the crossroads?

    International Nuclear Information System (INIS)

    Buescher, T.; Weber, R.

    2003-01-01

    Under the auspices of the Young Generation within KTG, young engineers met in Gronau on November 7-11, 2002 upon invitation by URENCO in order to discuss a variety of aspects of the future of nuclear power in Germany. Among the points emphasized were personal commitment and the need to discuss the topic of nuclear power under ethical aspects. (orig.)

  14. Pressure difference receiving ears

    DEFF Research Database (Denmark)

    Michelsen, Axel; Larsen, Ole Næsbye

    2007-01-01

    Directional sound receivers are useful for locating sound sources, and they can also partly compensate for the signal degradations caused by noise and reverberations. Ears may become inherently directional if sound can reach both surfaces of the eardrum. Attempts to understand the physics...... of the eardrum. The mere existence of sound transmission to the inner surface does not ensure a useful directional hearing, since a proper amplitude and phase relationship must exist between the sounds acting on the two surfaces of the eardrum. The gain of the sound pathway must match the amplitude and phase...... of the sounds at the outer surfaces of the eardrums, which are determined by diffraction and by the arrival time of the sound, that is by the size and shape of the animal and by the frequency of sound. Many users of hearing aids do not obtain a satisfactory improvement of their ability to localize sound sources...

  15. Search for Single Top Production at LEP

    CERN Document Server

    Achard, P; Aguilar-Benítez, M; Alcaraz, J; Alemanni, G; Allaby, James V; Aloisio, A; Alviggi, M G; Anderhub, H; Andreev, V P; Anselmo, F; Arefev, A; Azemoon, T; Aziz, T; Bagnaia, P; Bajo, A; Baksay, G; Baksay, L; Baldew, S V; Banerjee, S; Banerjee, Sw; Barczyk, A; Barillère, R; Bartalini, P; Basile, M; Batalova, N; Battiston, R; Bay, A; Becattini, F; Becker, U; Behner, F; Bellucci, L; Berbeco, R; Berdugo, J; Berges, P; Bertucci, B; Betev, B L; Biasini, M; Biglietti, M; Biland, A; Blaising, J J; Blyth, S C; Bobbink, Gerjan J; Böhm, A; Boldizsar, L; Borgia, B; Bottai, S; Bourilkov, D; Bourquin, Maurice; Braccini, S; Branson, J G; Brochu, F; Burger, J D; Burger, W J; Cai, X D; Capell, M; Cara Romeo, G; Carlino, G; Cartacci, A M; Casaus, J; Cavallari, F; Cavallo, N; Cecchi, C; Cerrada, M; Chamizo-Llatas, M; Chang, Y H; Chemarin, M; Chen, A; Chen, G; Chen, G M; Chen, H F; Chen, H S; Chiefari, G; Cifarelli, Luisa; Cindolo, F; Clare, I; Clare, R; Coignet, G; Colino, N; Costantini, S; de la Cruz, B; Cucciarelli, S; van Dalen, J A; De Asmundis, R; Déglon, P L; Debreczeni, J; Degré, A; Dehmelt, K; Deiters, K; Della Volpe, D; Delmeire, E; Denes, P; De Notaristefani, F; De Salvo, A; Diemoz, M; Dierckxsens, M; Dionisi, C; Dittmar, M; Doria, A; Dova, M T; Duchesneau, D; Echenard, B; Eline, A; El-Mamouni, H; Engler, A; Eppling, F J; Ewers, A; Extermann, P; Falagán, M A; Falciano, S; Favara, A; Fay, J; Fedin, O; Felcini, M; Ferguson, T; Fesefeldt, H S; Fiandrini, E; Field, J H; Filthaut, Frank; Fisher, P H; Fisher, W; Fisk, I; Forconi, G; Freudenreich, Klaus; Furetta, C; Galaktionov, Yu; Ganguli, S N; García-Abia, P; Gataullin, M; Gentile, S; Giagu, S; Gong, Z F; Grenier, G; Grimm, O; Grünewald, M W; Guida, M; van Gulik, R; Gupta, V K; Gurtu, A; Gutay, L J; Haas, D; Hakobyan, R S; Hatzifotiadou, D; Hebbeker, T; Hervé, A; Hirschfelder, J; Hofer, H; Hohlmann, M; Holzner, G; Hou, S R; Hu, Y; Jin, B N; Jones, L W; de Jong, P; Josa-Mutuberria, I; Käfer, D; Kaur, M; Kienzle-Focacci, M N; Kim, J K; Kirkby, Jasper; Kittel, E W; Klimentov, A; König, A C; Kopal, M; Koutsenko, V F; Kräber, M H; Krämer, R W; Krenz, W; Krüger, A; Kunin, A; Ladrón de Guevara, P; Laktineh, I; Landi, G; Lebeau, M; Lebedev, A; Lebrun, P; Lecomte, P; Lecoq, P; Le Coultre, P; Le Goff, J M; Leiste, R; Levtchenko, M; Levchenko, P M; Li, C; Likhoded, S A; Lin, C H; Lin, W T; Linde, Frank L; Lista, L; Liu, Z A; Lohmann, W; Longo, E; Lü, Y S; Lübelsmeyer, K; Luci, C; Luminari, L; Lustermann, W; Ma Wen Gan; Malgeri, L; Malinin, A; Maña, C; Mangeol, D J J; Mans, J; Martin, J P; Marzano, F; Mazumdar, K; McNeil, R R; Mele, S; Merola, L; Meschini, M; Metzger, W J; Mihul, A; Milcent, H; Mirabelli, G; Mnich, J; Mohanty, G B; Muanza, G S; Muijs, A J M; Musicar, B; Musy, M; Nagy, S; Natale, S; Napolitano, M; Nessi-Tedaldi, F; Newman, H; Niessen, T; Nisati, A; Nowak, H; Ofierzynski, R A; Organtini, G; Palomares, C; Pandoulas, D; Paolucci, P; Paramatti, R; Passaleva, G; Patricelli, S; Paul, T; Pauluzzi, M; Paus, C; Pauss, Felicitas; Pedace, M; Pensotti, S; Perret-Gallix, D; Petersen, B; Piccolo, D; Pierella, F; Pioppi, M; Piroué, P A; Pistolesi, E; Plyaskin, V; Pohl, M; Pozhidaev, V; Pothier, J; Prokofiev, D O; Prokofev, D; Quartieri, J; Rahal-Callot, G; Rahaman, M A; Raics, P; Raja, N; Ramelli, R; Rancoita, P G; Ranieri, R; Raspereza, A V; Razis, P A; Ren, D; Rescigno, M; Reucroft, S; Riemann, S; Riles, K; Roe, B P; Romero, L; Rosca, A; Rosier-Lees, S; Roth, S; Rosenbleck, C; Roux, B; Rubio, Juan Antonio; Ruggiero, G; Rykaczewski, H; Sakharov, A; Saremi, S; Sarkar, S; Salicio, J; Sánchez, E; Sanders, M P; Schäfer, C; Shchegelskii, V; Schmidt-Kärst, S; Schmitz, D; Schopper, Herwig Franz; Schotanus, D J; Schwering, G; Sciacca, C; Servoli, L; Shevchenko, S; Shivarov, N; Shoutko, V; Shumilov, E; Shvorob, A V; Siedenburg, T; Son, D; Souga, C; Spillantini, P; Steuer, M; Stickland, D P; Stoyanov, B; Strässner, A; Sudhakar, K; Sultanov, G G; Sun, L Z; Sushkov, S V; Suter, H; Swain, J D; Szillási, Z; Tang, X W; Tarjan, P; Tauscher, Ludwig; Taylor, L; Tellili, B; Teyssier, D; Timmermans, C; Ting, Samuel C C; Ting, S M; Tonwar, S C; Tóth, J; Tully, C; Tung, K L; Ulbricht, J; Valente, E; Van de Walle, R T; Vásquez, R P; Veszpremi, V; Vesztergombi, G; Vetlitskii, I; Vicinanza, D; Viertel, Gert M; Villa, S; Vivargent, M; Vlachos, S; Vodopyanov, I; Vogel, H; Vogt, H; Vorobev, I; Vorobyov, A A; Wadhwa, M; Wallraff, W; Wang, X L; Wang, Z M; Weber, M; Wienemann, P; Wilkens, H; Wynhoff, S; Xia, L; Xu, Z Z; Yamamoto, J; Yang, B Z; Yang, C G; Yang, H J; Yang, M; Yeh, S C; Zalite, A; Zalite, Yu; Zhang, Z P; Zhao, J; Zhu, G Y; Zhu, R Y; Zhuang, H L; Zichichi, A; Zimmermann, B; Zöller, M

    2002-01-01

    Single top production in e^+e^- annihilations is searched for in data collected by the L3 detector at centre-of-mass energies from 189 to 209 GeV, corresponding to a total integrated luminosity of 634 pb-1. Investigating hadronic and semileptonic top decays, no evidence of single top production at LEP is obtained and upper limits on the single top cross section as a function of the centre-of-mass energy are derived. Limits on possible anomalous couplings, as well as on the scale of contact interactions responsible for single top production are determined.

  16. Single top quark production with CMS

    Directory of Open Access Journals (Sweden)

    Piccolo Davide

    2013-11-01

    Full Text Available Measurements of single top quark production performed using the CMS experiment [1] data collected in 2011 at centre-of-mass energies of 7 TeV and in 2012 at 8 TeV, are presented. The cross sections for the electroweak production of single top quarks in the t-channel and in association with W-bosons is measured and the results are used to place constraints on the CKM matrix element Vtb. Measurements of top quark properties in single top quark production are also presented. The results include the measurement of the charge ratio in the single top t-channel.

  17. CP Violation in Single Top Quark Production

    Energy Technology Data Exchange (ETDEWEB)

    Geng, Weigang [Michigan State Univ., East Lansing, MI (United States)

    2012-01-01

    We present a search for CP violation in single top quark production with the DØ experiment at the Tevatron proton-antiproton collider. CP violation in the top electroweak interaction results in different single top quark production cross sections for top and antitop quarks. We perform the search in the single top quark final state using 5.4 fb-1 of data, in the s-channel, t-channel, and for both combined. At this time, we do not see an observable CP asymmetry.

  18. Top quark physics at the LHC

    Directory of Open Access Journals (Sweden)

    Jeong Kim Tae

    2014-04-01

    Full Text Available In 2011, an integrated luminosity of more than 5 fb−1 at 7 TeV has been delivered by the LHC. The measurement of the cross section in top quark pair production and in single top quark production, top quark mass, top quark properties and new physics searches in top quark decays have been performed at the CMS experiment with various integrated luminosities. An overview of the latest results of these measurements and searches by the time of ICFP 2012 conference will be presented.

  19. Searching for the top at UA2

    International Nuclear Information System (INIS)

    Unal, G.

    1990-10-01

    The projects conceived for searching the quark top, predicted by the Standard Model, are described. The required existence of the quark top from the Standard Model and its production from proton-antiproton collisions are reviewed. The UA2 experimental device is described. The method applied for the search of the top is explained. The analysis of the UA2 data does not allow to conclude the existence of the top. However, the low mass limit of 69 GeV/C 2 can be established for the top mass. The results of the analysis of the W decays into supersymmetric particles are included [fr

  20. Top down electroweak dipole operators

    Science.gov (United States)

    Fuyuto, Kaori; Ramsey-Musolf, Michael

    2018-06-01

    We derive present constraints on, and prospective sensitivity to, the electric dipole moment (EDM) of the top quark (dt) implied by searches for the EDMs of the electron and nucleons. Above the electroweak scale v, the dt arises from two gauge invariant operators generated at a scale Λ ≫ v that also mix with the light fermion EDMs under renormalization group evolution at two-loop order. Bounds on the EDMs of first generation fermion systems thus imply bounds on |dt |. Working in the leading log-squared approximation, we find that the present upper bound on |dt | is 10-19 e cm for Λ = 1 TeV, except in regions of finely tuned cancellations that allow for |dt | to be up to fifty times larger. Future de and dn probes may yield an order of magnitude increase in dt sensitivity, while inclusion of a prospective proton EDM search may lead to an additional increase in reach.

  1. Ultrasonic Testing of NIF Amplifier FAU Top Plates

    International Nuclear Information System (INIS)

    Chinn, D.J.; Huber, R.D.; Haskins, J.J.; Rodriguez, J.A.; Souza, P.R.; Le, T.V.

    2002-01-01

    A key component in the National Ignition Facility (NIF) laser optic system is the amplifier frame assembly unit (FAU). The cast aluminum top plate that supports the FAU is required to withstand loads that would occur during an earthquake with a recurrence period of 1000 years. The stringent seismic requirements placed on the FAU top plate induced a study of the cast aluminum material used in the top plate. Ultrasonic testing was used to aid in characterizing the aluminum material used in the plates. This report documents the work performed using contact ultrasonic testing to characterize the FAU top plate material. The ultrasonic work reported here had 3 objectives: (1) inspect the plate material before cyclic testing conducted at the Pacific Earthquake Engineering Research Center (PEER); (2) determine the overall quality of individual plates; and (3) detect large defects in critical areas of individual plates. Section III, ''Pre-cyclic test inspection'', describes work performed in support of Objective 1. Section IV, ''Ultrasonic field measurements'', describes work performed in support of Objectives 2 and 3

  2. Top Management Involvement in New Product Development

    DEFF Research Database (Denmark)

    Felekoglu, Burcu; Maier, Anja; Moultrie, James

    2010-01-01

    a broader conceptual space than this participation. This paper reviews the literature on top management involvement in new product development (NPD) and discusses relevance of different theoretical perspectives from other disciplines such as management, organisational behaviour and communication to analyse......Involvement of top managers in new product development (NPD) is a critical factor affecting NPD performance and frequently considered to be the participation of top management to certain activities in NPD or their NPD related behaviours. However, “Top management involvement in NPD” occupies...... antecedents, realisation and consequences of top management involvement in NPD. It is argued that top management has different involvement at different NPD levels: organisation level and project level. Resulting from this literature review, a tentative framework for top management involvement in NPD...

  3. Ground receiving station (GRS) of UMS - receiving and processing the electromagnetic wave data from satellite

    International Nuclear Information System (INIS)

    Mohammad Syahmi Nordin; Fauziah Abdul Aziz

    2007-01-01

    The low resolution Automatic Picture Transmission (APT) data from the National Oceanic and Atmospheric Administration (NOAA) polar-orbiting satellites Advanced Very High Resolution Radiometer (AVHRR) is being received and recorded in real-time mode at ground receiving station in School of Science and Technology, Universiti Malaysia Sabah. The system is suitable for the developing and undeveloped countries in south and Southeast Asia and is said to be acceptable for engineering, agricultural, climatological and environmental applications. The system comprises a personal computer attached with a small APT receiver. The data transmission between the ground receiving station and NOAA satellites is using the electromagnetic wave. The relation for receiving and processing the electromagnetic wave in the transmission will be discussed. (Author)

  4. Engineering Encounters: Engineering Adaptations

    Science.gov (United States)

    Gatling, Anne; Vaughn, Meredith Houle

    2015-01-01

    Engineering is not a subject that has historically been taught in elementary schools, but with the emphasis on engineering in the "Next Generation Science Standards," curricula are being developed to explicitly teach engineering content and design. However, many of the scientific investigations already conducted with students have…

  5. Ravimimüüjate TOP 30 aastal 2002

    Index Scriptorium Estoniae

    2003-01-01

    Ravimimüüjate TOP 30 aastal 2002. Käibe TOP 30. Kasumi TOP 30. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Ravimimüüjad 2002: üld- ja finantsandmed

  6. Tekstiilitööstuse TOP 30 aastal 2002

    Index Scriptorium Estoniae

    2003-01-01

    Tekstiilitööstuse TOP 30. Kasumi TOP 30. Käibe TOP 30. Rentaabluse TOP 20. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Omakapitali tootlikkuse TOP 20. Tekstiilitööstuse ettevõtted 2002: üld- ja finantsandmed

  7. Trükitööstuste TOP 50

    Index Scriptorium Estoniae

    2002-01-01

    Trükitööstuste TOP 50. Käibe TOP 30. Käibe kasum TOP 30. Kasvu TOP 30. Kasumi kasvu TOP 30. Rentaabluse TOP. Varade tootlikkuse TOP. Trükitööstusettevõtete üldandmed. Trükitööstusettevõtete finantsandmed

  8. Rõivatööstuse TOP 40 aastal 2002

    Index Scriptorium Estoniae

    2003-01-01

    Rõivatööstuse TOP 40. Käibe TOP 40. Kasumi TOP 40. Käibe kasvu TOP 20. Kasumi kasvu TOP 20. Rentaabluse TOP 20. Omakapitali tootlikkuse TOP 20. Rõivatööstuse ettevõtted: üldandmed ja finantsandmed

  9. Läänemaa ettevõtete TOP 50

    Index Scriptorium Estoniae

    2005-01-01

    Läänemaa ettevõtete TOP 50; Käibe TOP 35; Kasumi TOP 35; Käibe kasvu TOP 20; Kasumi kasvu TOP 20; Rentaabluse TOP 20; Omakapitali tootlikkuse TOP 20; Läänemaa ettevõtete üld- ja finantsandmed

  10. Ida-Virumaa ettevõtete TOP 50

    Index Scriptorium Estoniae

    2005-01-01

    Ilmunud ka: Delovõje Vedomosti-Severo-Vostok 7. sept. lk. 4. Ida-Virumaa ettevõtete TOP 50; Käibe TOP 35; Kasumi TOP 35; Käibe kasvu TOP 20; Kasumi kasvu TOP 20; Rentaabluse TOP 20; Omakapitali tootlikkuse TOP 20; Ida-Virumaa ettevõtete üld- ja finantsandmed

  11. Toiduainetööstuse TOP 100 aastal 2001

    Index Scriptorium Estoniae

    2002-01-01

    TOP 100. Toiduainetööstuste rentaabluse TOP 40. Varade tootlikkuse TOP 40. Käibe TOP 50. Käibe kasvu TOP 50. Kasumi TOP 50. Kasumi kasvu TOP 50. Toiduainetööstuse finantsandmed aastal 2001. Toiduainetööstuse üldandmed aastal 2001

  12. CERN apprentice receives award

    CERN Multimedia

    2008-01-01

    Another CERN apprentice has received an award for the quality of his work. Stéphane Küng (centre), at the UIG ceremony last November, presided over by Geneva State Councillor Pierre-François Unger, Head of the Department of Economics and Health. Electronics technician Stéphane Küng was honoured in November by the Social Foundation of the Union Industrielle Genevoise (UIG) as one of Geneva’s eight best apprentices in the field of mechatronics. The 20-year-old Genevan obtained his Federal apprentice’s certificate (Certificat fédéral de capacité - CFC) in June 2007, achieving excellent marks in his written tests at the Centre d’Enseignement Professionnel Technique et Artisanal (CEPTA). Like more than 200 youngsters before him, Stéphane Küng spent part of his four-year sandwich course working at CERN, where he followed many practical training courses and gained valuable hands-on experience in various technical groups and labs. "It’ always very gr...

  13. Lääne-Virumaa TOP 100 aastal 2000

    Index Scriptorium Estoniae

    2001-01-01

    Lääne-Virumaa edukamad ettevõtted; Lääne-Virumaa käibe TOP 100; Käibe kasvu TOP 20; Käibe languse TOP 10; Kasumi TOP 20; Kasumi kasvu TOP 20; Rentabluse TOP 20; ROA TOP 20; Kasumi languse TOP 10; Kahjumi TOP 10; Lääne-Virumaa käibelt suuremate ettevõtete finantsandmed. Lääne-Virumaa ettevõtete üldandmed

  14. GNSS Software Receiver for UAVs

    DEFF Research Database (Denmark)

    Olesen, Daniel Madelung; Jakobsen, Jakob; von Benzon, Hans-Henrik

    2016-01-01

    This paper describes the current activities of GPS/GNSS Software receiver development at DTU Space. GNSS Software receivers have received a great deal of attention in the last two decades and numerous implementations have already been presented. DTU Space has just recently started development of ...... of our own GNSS software-receiver targeted for mini UAV applications, and we will in in this paper present our current progress and briefly discuss the benefits of Software Receivers in relation to our research interests....

  15. Top-of-Rail lubricant

    Energy Technology Data Exchange (ETDEWEB)

    Alzoubi, M. F.; Fenske, G. R.; Erck, R. A.; Boparai, A. S.

    2000-07-14

    Analysis of the volatile and semivolatile fractions collected after use of the TOR lubricant indicated that other than contaminants in the collection laboratory, no compounds on the EPA's Target Compound Lists (Tables 2 and 5) were detected in these fractions. The data of these qualitative analyses, given in the various tables in the text, indicate only the relative amounts of the tentatively identified compounds. The authors recommend that quantitative analysis be performed on the volatile and semivolatile fractions to allow confirmation of the tentatively identified compounds and to obtain absolute amounts of the detected compounds. Additionally, the semivolatile fraction should be analyzed by liquid chromatography/mass spectrometry to identify compounds that are not chromatographable under the temperature program used for determination of semivolatile compounds. Introducing the top-of-rail (TOR) lubricant into the wheel/rail interface results in a reduction of almost 60% of lateral friction force over the forces encountered under dry conditions. This reveals good potential for energy savings, as well as wear reduction, for railroad companies. In TOR lubrication, an increase in the angle of attack and axle load results in increased lateral friction and rate of lubricant consumption. The most efficient TOR lubricant quantity to be used in the wheel/rail interface must be calculated precisely according to the number of cars, axle loads, train speed, and angle of attack.

  16. Top medical news stories 2015

    Directory of Open Access Journals (Sweden)

    Robbins RA

    2015-12-01

    Full Text Available No abstract available. Article truncated after 150 words. Here is our list of the top seven medical news stories for 2015 with special emphasis on the Southwest. 7. Wearable health devices: A wave of wearable computing devices such as Fitbit and UP wristbands have people keeping track of how much they sit, stand, walk, climb stairs and calories they consume (1. These fitness-tracking devices herald a series of devices that will detect and monitor serious diseases. However, these so-called medical-grade wearables require approval from the U.S. Food and Drug Administration, a regulatory hurdle avoided by the fitness-tracking devices which will likely slow their introduction. 6. Caitlyn Jenner: Caitlyn Jenner became the most famous transgender woman in the world following an interview published in Vanity Fair (2. The Vanity Fair website saw 11.6 million visits curious about the former Olympic athlete. Though Jenner publicly shared her gender identity, many transgender Americans do not-12% of gender non-conforming adults said they ...

  17. Measurement of top properties in ATLAS

    CERN Document Server

    Veloso, F; The ATLAS collaboration

    2010-01-01

    The top quark may play a special role in the Standard Model of particle physics. It is, for instance, the heaviest fundamental particle known, with a mass close to the electroweak symmetry breaking scale. Millions of top quark pairs will be produced per year at the LHC at nominal luminosity. ATLAS will measure many of the top quark properties with unprecedented precision. The ATLAS sensitivity studies done with Monte Carlo for the measurements of the top quark mass, the top quark charge, rare top quark decays and flavour changing neutral currents, the $t\\bar t$ spin correlations and $W$ boson polarization, the anomalous couplings at the $Wtb$ vertex and $t\\bar t$ resonances are reviewed.

  18. Qinshan CANDU project open top construction method

    International Nuclear Information System (INIS)

    Petrunik, K.J.; Wittann, K.; Khan, A.; Ricciuti, R.; Ivanov, A.; Chen, S.

    2003-01-01

    The significant schedule reductions achieved on the Qinshan CANDU Project were due in large part to the incorporation of advanced construction technologies in project design and delivery. For the Qinshan Project, a number of key advantages were realized through the use of the 'Open Top' construction method. This paper discusses the Qinshan Phase III CANDU Project Open Top implementation method. The Open Top method allowed major equipment to be installed simply, via the use of a Very Heavy Lift (VHL) crane and permitted the use of large-scale modularization. The advantages of Open Top construction, such as simplified access, more flexible project scheduling, improved construction safety and quality, and reduced labours are presented. The large-scale modularization of the Reactor Building Dousing System and the Open Top installation method and advantages relative to traditional CANDU 6 construction practices are also presented. Finally, major improvements for future CANDU plant construction using the Open Top method are discussed. (author)

  19. The significance of the heavy top quark

    International Nuclear Information System (INIS)

    Simmons, Elizabeth H.

    1997-01-01

    Experiment shows that the top quark is far heavier than the other elementary fermions. This finding has stimulated research on theories of electroweak and flavor symmetry breaking that include physics beyond the standard model. Efforts to accommodate a heavy top quark within existing frameworks have revealed constraints on model-building. Other investigations have started from the premise that a large top quark mass could signal a qualitative difference between the top quark and other fermions, perhaps in the form of new interactions peculiar to the top quark. Such new dynamics may also help answer existing questions about electroweak and flavor physics. This talk explores the implications of the heavy top quark in the context of weakly-coupled (e.g., SUSY) and strongly-coupled (e.g., technicolor) theories of electroweak symmetry breaking

  20. Top quark mass measurements with CMS

    CERN Document Server

    Kovalchuk, Nataliia

    2017-01-01

    Measurements of the top quark mass are presented, obtained from CMS data collected in proton-proton collisions at the LHC at centre-of-mass energies of 7 TeV and 8 TeV. The mass of the top quark is measured using several methods and channels, including the reconstructed invariant mass distribution of the top quark, an analysis of endpoint spectra as well as measurements from shapes of top quark decay distributions. The dependence of the mass measurement on the kinematic phase space is investigated. The results of the various channels are combined and compared to the world average. The top mass and also $\\alpha_{\\textnormal S}$ are extracted from the top pair cross section measured at CMS.

  1. TOP500 Supercomputers for November 2004

    Energy Technology Data Exchange (ETDEWEB)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2004-11-08

    24th Edition of TOP500 List of World's Fastest Supercomputers Released: DOE/IBM BlueGene/L and NASA/SGI's Columbia gain Top Positions MANNHEIM, Germany; KNOXVILLE, Tenn.; BERKELEY, Calif. In what has become a closely watched event in the world of high-performance computing, the 24th edition of the TOP500 list of the worlds fastest supercomputers was released today (November 8, 2004) at the SC2004 Conference in Pittsburgh, Pa.

  2. TOP500 Supercomputers for June 2004

    Energy Technology Data Exchange (ETDEWEB)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2004-06-23

    23rd Edition of TOP500 List of World's Fastest Supercomputers Released: Japan's Earth Simulator Enters Third Year in Top Position MANNHEIM, Germany; KNOXVILLE, Tenn.;&BERKELEY, Calif. In what has become a closely watched event in the world of high-performance computing, the 23rd edition of the TOP500 list of the world's fastest supercomputers was released today (June 23, 2004) at the International Supercomputer Conference in Heidelberg, Germany.

  3. Top Quark Production at Hadron Colliders

    Energy Technology Data Exchange (ETDEWEB)

    Phaf, Lukas Kaj [Univ. of Amsterdam (Netherlands)

    2004-03-01

    This thesis describes both theoretical and experimental research into top quark production. The theoretical part contains a calculation of the single-top quark production cross section at hadron colliders, at Next to Leading Order (NLO) accuracy. The experimental part describes a measurement of the top quark pair production cross section in proton-antiproton collisions, at a center of mass energy of 1.96 TeV.

  4. A table top exercise and workshop

    International Nuclear Information System (INIS)

    Lakey, J.R.A.

    1992-01-01

    Table top exercises are widely applied in training for emergency preparedness and have long been a feature of Courses on Planning for Nuclear Emergencies. Experience of a large number of table top exercises is used to provide a classification of the types of exercise indicating the application and the disadvantages. The use of workshops is considered to be complementary rather than an alternative to teaching methods available from table top exercises. (author)

  5. A heat receiver design for solar dynamic space power systems

    Science.gov (United States)

    Baker, Karl W.; Dustin, Miles O.; Crane, Roger

    1990-01-01

    An advanced heat pipe receiver designed for a solar dynamic space power system is described. The power system consists of a solar concentrator, solar heat receiver, Stirling heat engine, linear alternator and waste heat radiator. The solar concentrator focuses the sun's energy into a heat receiver. The engine and alternator convert a portion of this energy to electric power and the remaining heat is rejected by a waste heat radiator. Primary liquid metal heat pipes transport heat energy to the Stirling engine. Thermal energy storage allows this power system to operate during the shade portion of an orbit. Lithium fluoride/calcium fluoride eutectic is the thermal energy storage material. Thermal energy storage canisters are attached to the midsection of each heat pipe. The primary heat pipes pass through a secondary vapor cavity heat pipe near the engine and receiver interface. The secondary vapor cavity heat pipe serves three important functions. First, it smooths out hot spots in the solar cavity and provides even distribution of heat to the engine. Second, the event of a heat pipe failure, the secondary heat pipe cavity can efficiently transfer heat from other operating primary heat pipes to the engine heat exchanger of the defunct heat pipe. Third, the secondary heat pipe vapor cavity reduces temperature drops caused by heat flow into the engine. This unique design provides a high level of reliability and performance.

  6. Top Physics at CMS/LHC

    Directory of Open Access Journals (Sweden)

    Daskalakis Georgios

    2017-01-01

    Full Text Available Recent results on the inclusive and differential production cross sections of top-quark pair and single top-quark processes are presented, obtained using data from proton-proton collisions collected with the CMS detector at the LHC. The large centre-of-mass energies available at LHC allow for the copious production of top-quark pairs in association with other final state particles at high transverse momentum. Measurements of such processes as well as of the top-quark mass and other properties will be discussed. The results are compared with the most up-to-date standard model theory predictions.

  7. Differential Top Cross-section Measurements

    CERN Document Server

    Fenton, Michael James; The ATLAS collaboration

    2017-01-01

    The top quark is the heaviest known fundamental particle. The measurement of the differential top-quark pair production cross-section provides a stringent test of advanced perturbative QCD calculations. The ATLAS collaboration has performed detailed measurements of those differential cross sections at a centre-of-mass energy of 13 TeV. This talk focuses on differential cross-section measurements in the lepton+jets final state, including using boosted top quarks to probe our understanding of top quark production in the TeV regime.

  8. Top quark production cross-section measurements

    CERN Document Server

    Chen, Ye; The ATLAS collaboration

    2017-01-01

    Measurements of the inclusive and differential cross-sections for top-quark pair and single top production cross sections in proton-proton collisions with the ATLAS detector at the Large Hadron Collider are presented at center-of-mass energies of 8 TeV and 13 TeV. The inclusive measurements reach high precision and are compared to the best available theoretical calculations. These measurements, including results using boosted tops, probe our understanding of top-pair production in the TeV regime. The results are compared to Monte Carlo generators implementing LO and NLO matrix elements matched with parton showers and NLO QCD calculations. For the t-channel single top measurement, the single top-quark and anti-top-quark total production cross-sections, their ratio, as well as differential cross sections are also presented. A measurement of the production cross-section of a single top quark in association with a W boson, the second largest single-top production mode, is also presented. Finally, measurements of ...

  9. 2nd International Conference on Health Care Systems Engineering

    CERN Document Server

    Sahin, Evren; Li, Jingshan; Guinet, Alain; Vandaele, Nico

    2016-01-01

    In this volume, scientists and practitioners write about new methods and technologies for improving the operation of health care organizations. Statistical analyses play an important role in these methods with the implications of simulation and modeling applied to the future of health care. Papers are based on work presented at the Second International Conference on Health Care Systems Engineering (HCSE2015) in Lyon, France. The conference was a rare opportunity for scientists and practitioners to share work directly with each other. Each resulting paper received a double blind review. Paper topics include: hospital drug logistics, emergency care, simulation in patient care, and models for home care services. Discusses statistical analysis and operations management for health care delivery systems based on real case studies Papers in this volume received a double blind review Brings together the work of scientists, practitioners, and clinicians to unite research and practice in the future of these systems Top...

  10. Dish/stirling hybrid-receiver

    Science.gov (United States)

    Mehos, Mark S.; Anselmo, Kenneth M.; Moreno, James B.; Andraka, Charles E.; Rawlinson, K. Scott; Corey, John; Bohn, Mark S.

    2002-01-01

    A hybrid high-temperature solar receiver is provided which comprises a solar heat-pipe-receiver including a front dome having a solar absorber surface for receiving concentrated solar energy, a heat pipe wick, a rear dome, a sidewall joining the front and the rear dome, and a vapor and a return liquid tube connecting to an engine, and a fossil fuel fired combustion system in radial integration with the sidewall for simultaneous operation with the solar heat pipe receiver, the combustion system comprising an air and fuel pre-mixer, an outer cooling jacket for tangentially introducing and cooling the mixture, a recuperator for preheating the mixture, a burner plenum having an inner and an outer wall, a porous cylindrical metal matrix burner firing radially inward facing a sodium vapor sink, the mixture ignited downstream of the matrix forming combustion products, an exhaust plenum, a fossil-fuel heat-input surface having an outer surface covered with a pin-fin array, the combustion products flowing through the array to give up additional heat to the receiver, and an inner surface covered with an extension of the heat-pipe wick, a pin-fin shroud sealed to the burner and exhaust plenums, an end seal, a flue-gas diversion tube and a flue-gas valve for use at off-design conditions to limit the temperature of the pre-heated air and fuel mixture, preventing pre-ignition.

  11. Handbook for sound engineers

    CERN Document Server

    Ballou, Glen

    2015-01-01

    Handbook for Sound Engineers is the most comprehensive reference available for audio engineers, and is a must read for all who work in audio.With contributions from many of the top professionals in the field, including Glen Ballou on interpretation systems, intercoms, assistive listening, and fundamentals and units of measurement, David Miles Huber on MIDI, Bill Whitlock on audio transformers and preamplifiers, Steve Dove on consoles, DAWs, and computers, Pat Brown on fundamentals, gain structures, and test and measurement, Ray Rayburn on virtual systems, digital interfacing, and preamplifiers

  12. Engineering Encounters: Reverse Engineering

    Science.gov (United States)

    McGowan, Veronica Cassone; Ventura, Marcia; Bell, Philip

    2017-01-01

    This column presents ideas and techniques to enhance your science teaching. This month's issue shares information on how students' everyday experiences can support science learning through engineering design. In this article, the authors outline a reverse-engineering model of instruction and describe one example of how it looked in our fifth-grade…

  13. Scenario-based table top simulations

    DEFF Research Database (Denmark)

    Broberg, Ole; Edwards, Kasper; Nielsen, J.

    2012-01-01

    This study developed and tested a scenario-based table top simulation method in a user-driven innovation setting. A team of researchers worked together with a user group of five medical staff members from the existing clinic. Table top simulations of a new clinic were carried out in a simple model...

  14. Experimental results on SUSY searches with top

    CERN Document Server

    Eifert, Till

    2014-01-01

    Searches for supersymmetric partner particles of the top and bottom quarks at the Large Hadron Collider are reviewed. The focus is on the status of searches for a relatively light partner of the top quark performed by the CMS and ATLAS Collaborations. No excess beyond Standard Model expectations is observed and exclusion limits are set on the masses of supersymmetric particles.

  15. Top quark property measurements at the LHC

    CERN Document Server

    Hawkings, Richard; The ATLAS collaboration

    2014-01-01

    Measurements of top quark properties performed at the Large Hadron Collider are reviewed, with a particular emphasis on top-pair charge asymmetries, spin correlations and polarization measurements performed by the ATLAS and CMS collaborations. The measurements are generally in good agreement with predictions from next-to-leading-order QCD calculations, and no deviations from Standard Model expectations have been seen.

  16. Top quark distributions in hadronic collisions

    CERN Document Server

    Frixione, Stefano; Nason, P; Ridolfi, G; Frixione, S; Mangano, M L; Nason, P; Ridolfi, G

    1995-01-01

    We present kinematical distributions for top quark pairs produced at the Tevatron \\ppbar\\ Collider, as predicted within Next-to-Leading-Order QCD. We consider single and double-inclusive distributions, and compare our results to those obtained with the shower Monte Carlo HERWIG. We discuss the implications of our findings for experimental issues such as the measurement of the top quark mass.

  17. Top 12 Web Resources for 2012

    Science.gov (United States)

    Gonzales, Lisa; Vodicka, Devin

    2012-01-01

    In this article, the authors describe some of the top websites recommended by colleagues for the Association of California School Administrators. The Top 12 for 2012 are: (1) Facebook (facebook.com); (2) Twitter (twitter.com); (3) Tungle (tungle.me); (4) FCMAT (fcmat.org); (5) YouSendIt (yousendit.com); (6) Slideshare (slideshare.net); (7) QR…

  18. Latest ATLAS measurements on top quark properties

    CERN Document Server

    Derue, Frederic; The ATLAS collaboration

    2017-01-01

    The top quark is unique among the known quarks in that it decays before it has an opportunity to form hadronic bound states. This makes measurements of its properties particularly interesting as one can access directly the properties of a bare quark. The latest measurements of these properties with the ATLAS detector at the LHC are presented using 8 TeV and 13 TeV data, excluding results from single top production. Measurements of top quark spin observables in top-antitop events, each sensitive to a different coefficient of the spin density matrix, are presented and compared to the Standard Model predictions. The helicity of the W boson from the top decays and the production angles of the top quark are further discussed. New results on the measurment of color flow effects in $t{\\bar t}$ events are presented. Limits on the rate of flavour changing neutral currents in the production or decay of the top quark are reported. The cross-section measurement of photons produced in association with top-quark pairs is a...

  19. Thermal design of top shield for PFBR

    International Nuclear Information System (INIS)

    Gajapathy, R.; Jalaludeen, S.; Selvaraj, A.; Bhoje, S.B.

    1988-01-01

    India's Liquid Metal Cooled Fast Breeder Reactor programme started with the construction of loop type 13MW(e) Fast Breeder Test Reactor (FBTR) which attained criticality in October 1985. With the experience of FBTR, the design work on pool type 500 MW(e) Prototype Fast Breeder Reactor (PFBR) which will be a forerunner for future commercial fast breeder reactors, has been started. The Top Shield forms the cover for the main vessel which contains the primary circuit. Argon cover gas separates the Top Shield from the free level of hot sodium pool (803K). The Top Shield which is of box type construction consists of control plug, two rotatable plugs and roof slab, assembled together, which provide biological shielding, thermal shielding and leak tight containment at the top of the main vessel. Heat is transferred from the sodium pool to the Top Shield through argon cover gas and through components supported by it and dipped in the sodium pool. The Top Shield should be maintained at the desired operating temperature by incorporating a cooling system inside it. Insulation may be provided below the bottom plate to reduce the heat load to the cooling system, if required. The thermal design of Top Shield consists of estimation of heat transfer to the Top Shield, selection of operating temperature, assessment of insulation requirement, design of cooling system and evaluation of transient temperature changes

  20. SWFSC/MMTD/CCE: Tagging and Tracking of Physeter (T-TOP/T-TOP2) 1997

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This research was devoted to studying sperm whale (Physeter macrocephalus) behavior. The principal study area for T-TOP and T-TOP2 was the Pioneer Seamount, 50...

  1. Measuring top-quark polarization in top-pair + missing-energy events.

    Science.gov (United States)

    Berger, Edmond L; Cao, Qing-Hong; Yu, Jiang-Hao; Zhang, Hao

    2012-10-12

    The polarization of a top quark can be sensitive to new physics beyond the standard model. Since the charged lepton from top-quark decay is maximally correlated with the top-quark spin, it is common to measure the polarization from the distribution in the angle between the charged lepton and the top-quark directions. We propose a novel method based on the charged lepton energy fraction and illustrate the method with a detailed simulation of top-quark pairs produced in supersymmetric top squark pair production. We show that the lepton energy ratio distribution that we define is very sensitive to the top-quark polarization but insensitive to the precise measurement of the top-quark energy.

  2. Top quark mass measurement in dilepton channel

    International Nuclear Information System (INIS)

    Lysak, R.

    2007-01-01

    In this work, we measured the top quark mass in tt'-' events produced in pp'-' interactions at the center-of-mass energy 1.96 TeV using CDF detector. We used dilepton in tt'-' events where both W bosons from top quarks are decaying into leptons. The data sample corresponds to 340 pb -1 . We found there 33 tt'-' candidates while expecting 10.5 ± 1.9 background events. In the measurement, we reconstruct one, representative mass for each event using the assumption about longitudinal momentum of in tt'-' system, in order to be able to kinematically solve the under-constrained system. The mass distributions (templates) are created for simulated signal and background events. Templates are parametrized in order to obtain smooth probability density functions. Likelihood maximization which includes these parametrized templates is then performed on reconstructed masses obtained from data sample in order to obtain final top quark mass estimate. The result of applying this procedure on data events is top quark mass estimate 169.5 +7. 7 - 7.2 (stat.) ± 4.0(syst.) GeV/c 2 for 30 out of 33 candidates, where the solution for top quark mass was found. This measurement was a part of first top quark mass measurement in dilepton channel at CDF in Run II. The top quark mass measured here is consistent with the CDF measurement in dilepton channel from Run I M top = 167.4 ± 10.3(stat.) ± 4.8(syst.) GeV/c 2 . Moreover, the combined result of four top quark mass measurements in dilepton channel from Run II (one of these four measurements is our measurement) M top = 167.9 ± 5.2(stat.) ± 3.7(syst.) GeV/c 2 significantly (by ∼ 40%) improved the precision of top quark mass determination from Run I. It should be also noted, that this combined result is consistent with measurement obtained in 'lepton+jets' channel at CDF in Run II (M top = 173.5 +3.9 -3.8 GeV/c 2 ). So, we don't have yet any indication about new physics beyond the Standard Model. My main contribution in this analysis was

  3. Top quark studies with the ATLAS detector

    CERN Document Server

    Capua, Marcella; The ATLAS collaboration

    2015-01-01

    The latest top quark studies in proton-proton collisions at a centre-of-mass energy of 7 and 8 TeV with the ATLAS detector are reported. We present recent results on the top pair production inclusive cross-sections, top pair production differential cross-section in the resolved and boosted regimes, single top-quark production cross-sections measured in the t-channel, s-channel and W-boson associated processes, as well as the CKM matrix element $|V_{tb}|$ determination. The results are compared with theoretical expectations. Latest ATLAS results on top properties will be also shown in terms of direct and mass pole, spin correlations and charge asymmetry.

  4. Top quark studies with the ATLAS detector

    CERN Document Server

    Capua, Marcella; The ATLAS collaboration

    2015-01-01

    The latest studies of top quark production measurement in proton-proton collisions at a centre-of-mass energy of 7 and 8 TeV with the ATLAS detector are reported. The talk will present recent results on the top pair production inclusive cross sections, top pair production differential cross section in resolved and boosted regime, single top-quark productions cross sections measured for t-channel, s-channel and W-boson associated processes. as well as d the CKM matrix element |Vtb| determination. All the results are compared with theoretical expectations. Latest ATLAS results on top mass measurements will be also shown in terms of direct and mass pole results.

  5. TOP500 Supercomputers for June 2002

    Energy Technology Data Exchange (ETDEWEB)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2002-06-20

    19th Edition of TOP500 List of World's Fastest Supercomputers Released MANNHEIM, Germany; KNOXVILLE, Tenn.;&BERKELEY, Calif. In what has become a much-anticipated event in the world of high-performance computing, the 19th edition of the TOP500 list of the worlds fastest supercomputers was released today (June 20, 2002). The recently installed Earth Simulator supercomputer at the Earth Simulator Center in Yokohama, Japan, is as expected the clear new number 1. Its performance of 35.86 Tflop/s (trillions of calculations per second) running the Linpack benchmark is almost five times higher than the performance of the now No.2 IBM ASCI White system at Lawrence Livermore National Laboratory (7.2 Tflop/s). This powerful leap frogging to the top by a system so much faster than the previous top system is unparalleled in the history of the TOP500.

  6. Top quark production at the LHC

    CERN Document Server

    Ferreira da Silva, Pedro

    2016-01-01

    Twenty years past its discovery, the top quark continues attracting great interest as experiments keep unveiling its properties. An overview of the latest measurements in the domain of top quark production, performed by the ATLAS and CMS experiments at the CERN LHC, is given. The latest measurements of top quark production rates via strong and electroweak processes are reported and compared to different perturbative QCD predictions. Fundamental properties, such as the mass or the couplings of the top quark, as well as re-interpretations seeking for beyond the standard model contributions in the top quark sector, are extracted from these measurements. In each case an attempt to highlight the first results and main prospects for the on-going Run 2 of the LHC is made.

  7. D OE top quark mass analysis

    International Nuclear Information System (INIS)

    Strovink, M.

    1995-07-01

    Based on (44-48 pb -1 ) of lepton + jets data, we review D0's initial analysis of the top quark mass. The result, M top = 199 ± 19/21 (stat.) ± 22 (syst.) GeV/c 2 , is insensitive to background normalization. The errors are based on ISAJET top Monte Carlo, with its more severe gluon radiation, and allow for ISAJET/HERWIG differences. Good progress is being made in reducing the systematic error. We present a new study based on two-dimensional distributions of reconstructed top quark vs. dijet mass. With 98.7% confidence we observe a peak in the top mass - dijet mass plane. The peak and its projections are similar both in shape and magnitude to expectations based on the decay sequence 1 → bW, W → jj

  8. Top quark production at the LHC (single top and tt-bar cross sections)

    International Nuclear Information System (INIS)

    Lange, J.

    2014-01-01

    With the large number of top quarks produced at the LHC, top quark physics enters an era of precision and properties measurements. This article reviews the recent advances in top quark cross section measurements performed by ATLAS and CMS using data recorded in 2011 with integrated luminosities up to 5 fb -1 . They include precision inclusive cross sections, the establishment of challenging channels, first differential cross section measurements and single top production. An overall good agreement with Standard Model predictions is observed

  9. 78 FR 1776 - Airworthiness Directives; International Aero Engines AG Turbofan Engines

    Science.gov (United States)

    2013-01-09

    ... Engines AG Turbofan Engines AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed... Aero Engines AG (IAE), V2525-D5 and V2528-D5 turbofan engines, with a certain number (No.) 4 bearing... proposed AD. Discussion We received a report of a fire warning on an IAE V2525 turbofan engine shortly...

  10. Measurements and searches with top quarks

    International Nuclear Information System (INIS)

    Peters, Reinhild Yvonne

    2008-01-01

    In 1995 the last missing member of the known families of quarks, the top quark, was discovered by the CDF and D0 experiments at the Tevatron, a proton-antiproton collider at Fermilab near Chicago. Until today, the Tevatron is the only place where top quarks can be produced. The determination of top quark production and properties is crucial to understand the Standard Model of particle physics and beyond. The most striking property of the top quark is its mass--of the order of the mass of a gold atom and close to the electroweak scale--making the top quark not only interesting in itself but also as a window to new physics. Due to the high mass, much higher than of any other known fermion, it is expected that the top quark plays an important role in electroweak symmetry breaking, which is the most prominent candidate to explain the mass of particles. In the Standard Model, electroweak symmetry breaking is induced by one Higgs field, producing one additional physical particle, the Higgs boson. Although various searches have been performed, for example at the Large Electron Positron Collider (LEP), no evidence for the Higgs boson could yet be found in any experiment. At the Tevatron, multiple searches for the last missing particle of the Standard Model are ongoing with ever higher statistics and improved analysis techniques. The exclusion or verification of the Higgs boson can only be achieved by combining many techniques and many final states and production mechanisms. As part of this thesis, the search for Higgs bosons produced in association with a top quark pair (t(bar t)H) has been performed. This channel is especially interesting for the understanding of the coupling between Higgs and the top quark. Even though the Standard Model Higgs boson is an attractive candidate, there is no reason to believe that the electroweak symmetry breaking is induced by only one Higgs field. In many models more than one Higgs boson are expected to exist, opening even more channels

  11. Discovery of single top quark production

    Energy Technology Data Exchange (ETDEWEB)

    Gillberg, Dag [Simon Fraser Univ., Burnaby, BC (Canada)

    2009-04-01

    The top quark is by far the heaviest known fundamental particle with a mass nearing that of a gold atom. Because of this strikingly high mass, the top quark has several unique properties and might play an important role in electroweak symmetry breaking - the mechanism that gives all elementary particles mass. Creating top quarks requires access to very high energy collisions, and at present only the Tevatron collider at Fermilab is capable of reaching these energies. Until now, top quarks have only been observed produced in pairs via the strong interaction. At hadron colliders, it should also be possible to produce single top quarks via the electroweak interaction. Studies of single top quark production provide opportunities to measure the top quark spin, how top quarks mix with other quarks, and to look for new physics beyond the standard model. Because of these interesting properties, scientists have been looking for single top quarks for more than 15 years. This thesis presents the first discovery of single top quark production. An analysis is performed using 2.3 fb-1 of data recorded by the D0 detector at the Fermilab Tevatron Collider at centre-of-mass energy √s = 1.96 TeV. Boosted decision trees are used to isolate the single top signal from background, and the single top cross section is measured to be σ(p$\\bar{p}$ → tb + X, tqb + X) = 3.74-0.74+0.95 pb. Using the same analysis, a measurement of the amplitude of the CKM matrix element Vtb, governing how top and b quarks mix, is also performed. The measurement yields: |V{sub tb}|f1L| = 1.05 -0.12+0.13, where f1L is the left-handed Wtb coupling. The separation of signal from background is improved by combining the boosted decision trees with two other multivariate techniques. A new cross section measurement is performed, and the significance for the excess over the predicted background exceeds 5

  12. The Top Quark, QCD, And New Physics.

    Science.gov (United States)

    Dawson, S.

    2002-06-01

    The role of the top quark in completing the Standard Model quark sector is reviewed, along with a discussion of production, decay, and theoretical restrictions on the top quark properties. Particular attention is paid to the top quark as a laboratory for perturbative QCD. As examples of the relevance of QCD corrections in the top quark sector, the calculation of e{sup+}e{sup -}+ t{bar t} at next-to-leading-order QCD using the phase space slicing algorithm and the implications of a precision measurement of the top quark mass are discussed in detail. The associated production of a t{bar t} pair and a Higgs boson in either e{sup+}e{sup -} or hadronic collisions is presented at next-to-leading-order QCD and its importance for a measurement of the top quark Yulrawa coupling emphasized. Implications of the heavy top quark mass for model builders are briefly examined, with the minimal supersymmetric Standard Model and topcolor discussed as specific examples.

  13. Top Quark Mass Measurement in Dilepton Channel

    Energy Technology Data Exchange (ETDEWEB)

    Lysak, Roman [Inst. of Experimental Physics, Kosice (Slovak Republic)

    2007-06-01

    We present a measurement of the top quark mass from events produced in p$\\bar{p}$ collisions at a center-of-mass energy of 1.96 TeV, using the Collider Detector at Fermilab. We identify t$\\bar{t}$ candidates where both W bosons from the top quarks decay into leptons (eν, µν, τν) from a data sample of 340 pb-1. The top quark mass is reconstructed in each event separately by the method which draw upon simulated distribution of t$\\bar{t}$ longitudinal momentum in order to extract probability distribution for the top quark mass. Representative distributions, or templates, are constructed from simulated samples of signal and background events, and parametrized to form continuous probability density functions. A likelihood fit incorporating these parametrized templates is then performed on the data sample masses in order to derive a final top quark mass. Measured top quark mass is Mtop = 169.5$+7.7\\atop{-7.2}$(stat.) ± 4.0(syst.) GeV/c2.

  14. Measurement of the top quark mass

    International Nuclear Information System (INIS)

    Blusk, Steven R.

    1998-01-01

    The first evidence and subsequent discovery of the top quark was reported nearly 4 years ago. Since then, CDF and D0 have analyzed their full Run 1 data samples, and analysis techniques have been refined to make optimal use of the information. In this paper, we report on the most recent measurements of the top quark mass, performed by the CDF and D0 collaborations at the Fermilab Tevatron. The CDF collaboration has performed measurements of the top quark mass in three decay channels from which the top quark mass is measured to be 175.5 ± 6.9 GeV=c 2 . The D0 collaboration combines measurements from two decay channels to obtain a top quark mass of 172.1 ± 7.1 GeV/c 2 . Combining the measurements from the two experiments, assuming a 2 GeV GeV/c 2 correlated systematic uncertainty, the measurement of the top quark mass at the Tevatron is 173.9 ± 5.2 GeV/c 2 . This report presents the measurements of the top quark mass from each of the decay channels which contribute to this measurement

  15. MOD/R : A knowledge assisted approach towards top-down only CMOS VLSI design

    NARCIS (Netherlands)

    Spaanenburg, L.; Beunder, M.; Beune, F.A.; Gerez, Sabih H.; Holstein, B.; Luchtmeyer, R.C.C.; Smit, Jaap; van der Werf, A.; Willems, H.

    1985-01-01

    MOD/R models all views on the design space in relations. This is achieved by eliminating the package constraints, as are apparent in PCB oriented hardware description languages. Assisted by knowledge engineering it allows for a top-down, mostly hierarchical decomposition, virtually eliminating the

  16. Hadronization systematics and top mass reconstruction

    Directory of Open Access Journals (Sweden)

    Corcella Gennaro

    2014-01-01

    Full Text Available I discuss a few issues related to the systematic error on the top mass mea- surement at hadron colliders, due to hadronization effects. Special care is taken about the impact of bottom-quark fragmentation in top decays, especially on the reconstruction relying on final states with leptons and J/Ψ in the dilepton channel. I also debate the relation between the measured mass and its theoretical definition, and report on work in progress, based on the Monte Carlo simulation of fictitious top-flavoured hadrons, which may shed light on this issue and on the hadronization systematics.

  17. TOP500 Supercomputers for June 2005

    Energy Technology Data Exchange (ETDEWEB)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2005-06-22

    25th Edition of TOP500 List of World's Fastest Supercomputers Released: DOE/L LNL BlueGene/L and IBM gain Top Positions MANNHEIM, Germany; KNOXVILLE, Tenn.; BERKELEY, Calif. In what has become a closely watched event in the world of high-performance computing, the 25th edition of the TOP500 list of the world's fastest supercomputers was released today (June 22, 2005) at the 20th International Supercomputing Conference (ISC2005) in Heidelberg Germany.

  18. Top quark pair production in ATLAS

    CERN Document Server

    Moreno Llacer, M; The ATLAS collaboration

    2010-01-01

    Top-quark pairs are expected to be produced at the LHC, even at the lower beam energy and luminosity in the first years of running. Establishing the top-pair signal and measuring the production cross-section are important benchmarks for ATLAS, and will help understand the detector performance for events with high-pT leptons, high jet multiplicity, missing transverse energy. The prospects for early top physics measurements will be shown, with a particular emphasis on the progress achieved with data so far.

  19. Search for top in UA2

    International Nuclear Information System (INIS)

    Repellin, J.P.

    1989-01-01

    A search for the top quark in the data collected during 1988 by the UA2 collaboration at the CERN proton-antiproton collider is presented. In UA2 the selected decay mode is t → eν-barb. The present report is limited to the study of topologies with an electron, a neutrino, and two or more jets. With an integrated luminosity of 2.5 pb -1 the data do not show any contribution from top and at this preliminary stage of the analysis a top mass between 30 and 60 GeV seems excluded. (K.A.) 9 refs.; 9 figs.; 2 tabs

  20. Precision Determination of the Top Quark Mass

    Energy Technology Data Exchange (ETDEWEB)

    Movilla Fernandez, Pedro A.; /LBL, Berkeley

    2007-05-01

    The CDF and D0 collaborations have updated their measurements of the mass of the top quark using proton-antiproton collisions at {radical}s = 1.96 TeV produced at the Tevatron. The uncertainties in each of the top-antitop decay channels have been reduced. The new Tevatron average for the mass of the top quark based on about 1 fb{sup -1} of data per experiment is 170.9 {+-} 1.8 GeV/c{sup 2}.

  1. Top quark mass measurement at the Tevatron

    Energy Technology Data Exchange (ETDEWEB)

    Guimaraes da Costa, Joao; /Harvard U.

    2004-12-01

    The authors report on the latest experimental measurements of the top quark mass by the CDF and D0 Collaborations at the Fermilab Tevatron. They present a new top mass measurement using the t{bar t} events collected by the D0 Collaboration in Run I between 1994 and 1996. This result is combined with previous measurements to yield a new world top mass average. They also describe several preliminary results using up to 193 pb{sup -1} of t{bar t} events produced in {bar p}p collisions at {radical}s = 1.96 TeV during the Run II of the Tevatron.

  2. Global constraints on top quark anomalous couplings

    Science.gov (United States)

    Déliot, Frédéric; Faria, Ricardo; Fiolhais, Miguel C. N.; Lagarelhos, Pedro; Onofre, António; Pease, Christopher M.; Vasconcelos, Ana

    2018-01-01

    The latest results on top quark physics, namely single top quark production cross sections, W -boson helicity and asymmetry measurements are used to probe the Lorentz structure of the W t b vertex. The increase of sensitivity to new anomalous physics contributions to the top quark sector of the standard model is quantified by combining the relevant results from Tevatron and the Large Hadron Collider. The results show that combining an increasing set of available precision measurements in the search for new physics phenomena beyond the standard model leads to significant sensitivity improvements, especially when compared with the current expectation for the High Luminosity run at the LHC.

  3. The de Sitter relativistic top theory

    International Nuclear Information System (INIS)

    Armenta, J.; Nieto, J.A.

    2005-01-01

    We discuss the relativistic top theory from the point of view of the de Sitter (or anti-de Sitter) group. Our treatment rests on the Hanson-Regge spherical relativistic top Lagrangian formulation. We propose an alternative method for studying spinning objects via Kaluza-Klein theory. In particular, we derive the relativistic top equations of motion starting with the geodesic equation for a point particle in 4+N dimensions. We compare our approach with Fukuyama's formulation of spinning objects, which is also based on Kaluza-Klein theory. We also report a generalization of our approach to a 4+N+D dimensional theory

  4. New Physics in Single-Top Production

    CERN Document Server

    Lohse, T; The ATLAS collaboration

    2014-01-01

    In this paper an overview of recent results on the search for physics beyond the Standard Model in the electro-weak top-quark production from the ATLAS, D0 , CDF and CMS collaborations is given. This includes searches for W' and b$^∗$ resonances as well as measurements of CP violation, the W helicity fractions and the top-quark polarisation in single-top production. A brief review on the search for flavour-changing neutral currents and cross-section measurements with respect to the CKM matrix element $V_{tb}$ is given.

  5. Top physics in ATLAS and CMS

    CERN Document Server

    Diez, Carmen

    2018-01-01

    A selection of recent results of top quark production performed by the ATLAS and CMS Collaborations at the LHC is presented. The results include measurements of top quark pair production, including inclusive and differential cross sections, as well as cross sections for ${\\rm t\\bar{t}}$ production in association with additional heavy-quark jets or additional bosons. The production of single top quarks via t-channel, tW associated production, and in association with a Z boson is also discussed. The results discussed are mostly obtained using data collected in proton-proton collisions at centre-of-mass energies of 8 and 13 TeV.

  6. Women in Top Management and Firm Performance

    DEFF Research Database (Denmark)

    Smith, Nina; Smith, Valdemar; Verner, Mette

    -observations for all Danish firms with more than 50 employees over the period 1994-2003, the analysis suggests that the proportion of women in top management jobs has from none to positive influence on firm performance. However, the results show that the strength of the effects of women in top management depends...... on how top CEOs are defined and on the method of estimation of the model. Next, the results point towards a positive influence on firm performance of the staff representation in the supervisory board of the firm but more women representing the shareholders in the supervisory board of the firm seems...

  7. Top 100 Cited Classic Articles in Breast Cancer Research.

    Science.gov (United States)

    Uysal, Erdal

    2017-07-01

    This study aimed to analyze 100 most cited articles in breast cancer research. The data in this study were obtained by a search conducted on the Web of Science (WOS). In brief, the term "breast cancer" was typed in the search box of WOS basic research including all the years and the data. The analysis was carried out by compiling the top 100 cited articles in the shortlist as sorted by the journals, categories of the studies, the countries, the centers, the authors and the publication date. No statistical methods were used in the study. All data were reported as percentages, numbers and bar charts on tables. Our findings showed that the most frequently cited article received 7609 citations to date. Most articles were published in the New England Journal of Medicine. 81% of the studies originated from the USA. The National Institutes of Health (NIH USA) was ranked the first with 21% and it was followed by Harvard University in terms of number of published articles. 42% of the articles were published under the category of medicine and general internal medicine. Top 100 most cited articles originated from the United States. The highest number of articles among the top 100 articles were published in New England Journal of Medicine and National Institutes of Health NIH USA was the leading institutes published the most articles.

  8. MHD Integrated Topping Cycle Project

    Science.gov (United States)

    1993-04-01

    Manufacture, assembly, and checkout of combustion subsystem hardware was completed and the hardware was delivered to CDIF along with the water electrical isolators. A successful nozzle proof test was concluded; its purpose was to evaluate adequacy of the nozzle structure and sealing of sidewall-to-electrode wall joints, water tubes, and stud and wire penetrations at operating pressure. Design modifications to spare channel inlet frame were made to enable iron oxide injection. Results of tests in the CDIF 1A1 channel which compared effect of different cathode wall iron oxide injection locations indicated that injection through the side port may be more effective, particularly if one of the two ports becomes clogged. Design confirmation testing of a pneumatically driven ram to clear a plugged iron oxide injector tip was performed. Manufacture of spare and replacement parts for 1A4 channel and diffuser was begun. Construction of the cathode power cabinets and associated control system was completed. Hot-fire checkout series was completed for the combustion subsystem; 16.8 thermal hours were accumulated during seven tests. This test series demonstrated adequacy of overall cooling of combustion subsystem and provided an initial evaluation of heat losses and slagging characteristics. Several major facility activities at the CDIF were accomplished including installation and testing of new iron oxide pumps, initial on-line checkout of coal feed system modifications, modification of seed system including replacement of silo rotary feeder, installation of new filter receiver on the silo, conversion of fly ash bin to dust collector, removal of all of the electrical wiring (used for 1A1 channel) between the channel and HVR in order to install 1A4 wiring, and installation of the 1A4 channel.

  9. Solar advanced internal film receiver

    International Nuclear Information System (INIS)

    Torre Cabezas, M. de la

    1990-01-01

    In a Solar Central Internal Film Receiver, the heat absorbing fluid (a molten nitrate salt) flows in a thin film down over the non illuminated side of an absorber panel. Since the molten salt working fluid is not contained in complicated tube manifolds, the receiver design is simples than a conventional tube type-receiver resulting in a lower cost and a more reliable receiver. The Internal Film Receiver can be considered as an alternative to the Direct Absorption Receiver, in the event that the current problems of the last one can not be solved. It also describes here the test facility which will be used for its solar test, and the test plans foreseen. (Author) 17 refs

  10. Communications receivers principles and design

    CERN Document Server

    Rohde, Ulrich L; Zahnd, Hans

    2017-01-01

    This thoroughly updated guide offers comprehensive explanations of the science behind today’s radio receivers along with practical guidance on designing, constructing, and maintaining real-world communications systems. You will explore system planning, antennas and antenna coupling, amplifiers and gain control, filters, mixers, demodulation, digital communication, and the latest software defined radio (SDR) technology. Written by a team of telecommunication experts, Communications Receivers: Principles and Design, Fourth Edition, features technical illustrations, schematic diagrams, and detailed examples. Coverage includes: • Basic radio considerations • Radio receiver characteristics • Receiver system planning • Receiver implementation considerations • RF and baseband techniques for Software-Defined Radios • Transceiver SDR considerations • Antennas and antenna coupling • Mixers • Frequency sources and control • Ancillary receiver circuits • Performance measurement

  11. Toiduainetööstuse TOP 100 aastal 2000

    Index Scriptorium Estoniae

    2001-01-01

    Toiduainetööstuse käibe TOP 75; Toiduainetööstuse käibekasvu TOP 60; Toiduainetööstuse kasumi TOP 80; Kahjumi TOP 15; Toiduainetööstuse kasumi kasvu TOP 60; Rentaabluse TOP 50; varade tootlikkuse TOP 50; Toiduainetööstuse finantsandmed aastal 2000; Toiduainetööstuse üldandmed aastal 2000

  12. Mechanical engineering

    International Nuclear Information System (INIS)

    1988-01-01

    The Mechanical Engineering Division provides the other NAC divisions with design and construction services. Items of special mechanical significance are discussed here. The projects which received major design attention during the past year were: a coupling capacitor for SPC2; a bending magnet and solenoid for ECR ion source; a scanner for outer orbits of the SSC; a scattering chamber for an experimental beamline; a beam swinger; a rotary target magazine for isotope production; a robot arm for isotope production; an isotope transport system and a target cooling system for isotope production. The major projects that were under construction are: a magnetic spectrometer; a second injector cyclotron (SPC2) and extensions to the high-energy beamlines. 4 figs

  13. Tower-Top Antenna Array Calibration Scheme for Next Generation Networks

    Directory of Open Access Journals (Sweden)

    McCormack Justine

    2007-01-01

    Full Text Available Recently, there has been increased interest in moving the RF electronics in basestations from the bottom of the tower to the top, yielding improved power efficiencies and reductions in infrastructural costs. Tower-top systems have faced resistance in the past due to such issues as increased weight, size, and poor potential reliability. However, modern advances in reducing the size and complexity of RF subsystems have made the tower-top model more viable. Tower-top relocation, however, faces many significant engineering challenges. Two such challenges are the calibration of the tower-top array and ensuring adequate reliability. We present a tower-top smart antenna calibration scheme designed for high-reliability tower-top operation. Our calibration scheme is based upon an array of coupled reference elements which sense the array's output. We outline the theoretical limits of the accuracy of this calibration, using simple feedback-based calibration algorithms, and present their predicted performance based on initial prototyping of a precision coupler circuit for a array. As the basis for future study a more sophisticated algorithm for array calibration is also presented whose performance improves with array size.

  14. Thermal analysis of GFRP-reinforced continuous concrete decks subjected to top fire

    Science.gov (United States)

    Hawileh, Rami A.; Rasheed, Hayder A.

    2017-12-01

    This paper presents a numerical study that investigates the behavior of continuous concrete decks doubly reinforced with top and bottom glass fiber reinforced polymer (GFRP) bars subjected to top surface fire. A finite element (FE) model is developed and a detailed transient thermal analysis is performed on a continuous concrete bridge deck under the effect of various fire curves. A parametric study is performed to examine the top cover thickness and the critical fire exposure curve needed to fully degrade the top GFRP bars while achieving certain fire ratings for the deck considered. Accordingly, design tables are prepared for each fire curve to guide the engineer to properly size the top concrete cover and maintain the temperature in the GFRP bars below critical design values in order to control the full top GFRP degradation. It is notable to indicate that degradation of top GFRP bars do not pose a collapse hazard but rather a serviceability concern since cracks in the negative moment region widen resulting in simply supported spans.

  15. Terascale Optimal PDE Simulations (TOPS) Center

    Energy Technology Data Exchange (ETDEWEB)

    Professor Olof B. Widlund

    2007-07-09

    Our work has focused on the development and analysis of domain decomposition algorithms for a variety of problems arising in continuum mechanics modeling. In particular, we have extended and analyzed FETI-DP and BDDC algorithms; these iterative solvers were first introduced and studied by Charbel Farhat and his collaborators, see [11, 45, 12], and by Clark Dohrmann of SANDIA, Albuquerque, see [43, 2, 1], respectively. These two closely related families of methods are of particular interest since they are used more extensively than other iterative substructuring methods to solve very large and difficult problems. Thus, the FETI algorithms are part of the SALINAS system developed by the SANDIA National Laboratories for very large scale computations, and as already noted, BDDC was first developed by a SANDIA scientist, Dr. Clark Dohrmann. The FETI algorithms are also making inroads in commercial engineering software systems. We also note that the analysis of these algorithms poses very real mathematical challenges. The success in developing this theory has, in several instances, led to significant improvements in the performance of these algorithms. A very desirable feature of these iterative substructuring and other domain decomposition algorithms is that they respect the memory hierarchy of modern parallel and distributed computing systems, which is essential for approaching peak floating point performance. The development of improved methods, together with more powerful computer systems, is making it possible to carry out simulations in three dimensions, with quite high resolution, relatively easily. This work is supported by high quality software systems, such as Argonne's PETSc library, which facilitates code development as well as the access to a variety of parallel and distributed computer systems. The success in finding scalable and robust domain decomposition algorithms for very large number of processors and very large finite element problems is, e

  16. Engineer Ethics

    International Nuclear Information System (INIS)

    Lee, Dae Sik; Kim, Yeong Pil; Kim, Yeong Jin

    2003-03-01

    This book tells of engineer ethics such as basic understanding of engineer ethics with history of engineering as a occupation, definition of engineering and specialized job and engineering, engineer ethics as professional ethics, general principles of ethics and its limitation, ethical theory and application, technique to solve the ethical problems, responsibility, safety and danger, information engineer ethics, biotechnological ethics like artificial insemination, life reproduction, gene therapy and environmental ethics.

  17. Giving top quark effective operators a boost

    CERN Document Server

    Englert, Christoph

    2016-01-01

    We investigate the prospects to systematically improve generic effective field theory-based searches for new physics in the top sector during LHC run 2 as well as the high luminosity phase. In particular, we assess the benefits of high momentum transfer final states on top EFT-fit as a function of systematic uncertainties in comparison with sensitivity expected from fully-resolved analyses focusing on $t\\bar t$ production. We find that constraints are typically driven by fully-resolved selections, while boosted top quarks can serve to break degeneracies in the global fit. This demystifies and clarifies the importance of high momentum transfer final states for global fits to new interactions in the top sector from direct measurements.

  18. Top 10 Myths about Cardiovascular Disease

    Science.gov (United States)

    ... Thromboembolism Aortic Aneurysm More Top 10 Myths about Cardiovascular Disease Updated:Mar 16,2018 How much do ... Healthy This content was last reviewed July 2015. Cardiovascular Conditions • Conditions Home • Arrhythmia and Atrial Fibrillation • Cardiac ...

  19. Impact loads on the pressure vessel top

    International Nuclear Information System (INIS)

    Krieg, R.; Malmberg, T.; Messemer, G.

    1995-01-01

    A steam explosion can cause core melt to be bounced against the internal side of the RPV top. The bouncing velocity up to which the top can withstand the impact is to be determined. Plausible assumptions about a core melt mass of 80000 kg result in a tolerable maximum bouncing velocity of about 200 m/s. Reliable estimates are expected from the BERDA experiments simulating a pessimistic course of events on a 1:10 scale. (orig.)

  20. Search for single top production at HERA

    International Nuclear Information System (INIS)

    Brandt, G.

    2008-01-01

    A search for single top production in e p collisions using the complete high-energy data from HERA is presented. This search is based on the analysis of events containing isolated leptons (electronic or muons) and missing transverse momentum P T miss . In the absence of a signal, an upper limit on the top production cross-section σ ep→etX tuγ T miss and the measurements of W boson polarisation fractions.

  1. Search for the top quark with CDF

    International Nuclear Information System (INIS)

    Barbaro-Galtieri, A.

    1991-01-01

    During the 1988--89 Tevatron Collider run the CDF detector has collected data for an integrated luminosity of 4.4 pb -1 . The sample has been used to search for the top quark in several topologies. Preliminary results show that a top mass below 89 GeV is excluded at the 95% confidence level, thus extending the limit of 77 GeV previously published by CDF. 14 refs., 8 figs

  2. Single Top-Quark Production at CDF

    CERN Multimedia

    CERN. Geneva

    2008-01-01

    The main challenge of the single top-quark search at the Tevatron is the huge background from W+jets events and QCD events, which makes the use of advanced multivariate techniques essential. The recent single top analyses using either the matrix element method, neural networks, likelihood discriminants or boosted decision trees as well as the combination of the former three analyses will be presented...

  3. Top Production Properties in ATLAS & CMS

    CERN Document Server

    Neep, Thomas James; The ATLAS collaboration

    2017-01-01

    The large mass and short lifetime of the top quark mean that it decays before forming bound states. This allows the top quark to be studied as a bare quark and opens up the possibility to measure many properties that can not be probed using other quarks. Precise study of these properties, including spin correlations, polarisations and asymmetries, may shed light on possible physics beyond the Standard Model.

  4. The discovery of the top quark

    International Nuclear Information System (INIS)

    Sinervo, P.K.

    1995-12-01

    The top quark and the Higgs boson are the heaviest elementary particles predicted by the standard model. The four lightest quark flavours, the up, down, strange and charm quarks, were well-established by the mid-1970's. The discovery in 1977 of the Τ resonances, a new family of massive hadrons, required the introduction of the fifth quark flavour. Experimental and theoretical studies have indicated that this quark also has a heavier partner, the top quark

  5. The Discovery of the Top Quark

    Science.gov (United States)

    Sinervo, P.K.

    1995-12-01

    The top quark and the Higgs boson are the heaviest elementary particles predicted by the standard model. The four lightest quark flavours, the up, down, strange and charm quarks, were well-established by the mid-1970's. The discovery in 1977 of the {Tau} resonances, a new family of massive hadrons, required the introduction of the fifth quark flavour. Experimental and theoretical studies have indicated that this quark also has a heavier partner, the top quark.

  6. Anomalous couplings in single top and searches for rare top quark couplings with the ATLAS detector

    CERN Document Server

    Cabrera Urban, Susana; The ATLAS collaboration

    2017-01-01

    The top quark is the heaviest known fundamental particle and probing its couplings with the other fundamental particle may open a window to physics beyond the Standard Model. Single top-quark production provides a unique window to study the coupling between the top quark, the W boson and the b quark, since it involves the $Wtb$ vertex in both production and decay. Measurements of angular correlations in single top quark events in the t-channel exchange of a W boson are presented based on the 8 TeV ATLAS dataset. Differential cross-sections are measured as a function of angular variables that are sensitive to anomalous contributions to the Wtb vertex and the top quark polarization. Searches for flavour-changing neutral current top-quark interactions are also discussed based on the 8 TeV and 13 TeV ATLAS dataset. Searches for rare top quark decays to Higgs and Z bosons are presented in top quark production, and searches for rare top quark interactions with gluons and Z bosons are presented in single top quark p...

  7. Humanitarian engineering in the engineering curriculum

    Science.gov (United States)

    Vandersteen, Jonathan Daniel James

    placements are a valuable pedagogical experience but risk benefiting the student disproportionately more than the receiving community. Local development placements offer different rewards and liabilities. To conclude, a major adjustment in engineering curriculum to address human development is appropriate and this new curriculum should include both local and international placements. However, the great force of altruism must be directed towards creating meaningful and lasting change.

  8. Recent top physics results from CMS

    CERN Multimedia

    CERN. Geneva

    2014-01-01

    The top quark, discovered in 1995 at the Tevatron, is the heaviest known elementary particle. The largeness of its mass gives rise to a number of peculiar properties: top quarks decay before they would hadronize and the measurement of their decay products provides direct access to its properties such as spin, charge, or polarization. The top quark couples most strongly with the Higgs boson, and plays a key role in the electro-weak symmetry breaking and in many scenarios of physics beyond the Standard Model. With its large center-of-mass energy and luminosity, the LHC produces top quarks in copious quantities, giving access to many new precision measurements. In this seminar, I will present recent measurements from the CMS experiment. I will focus in particular on the results on single-top quark production, where results are available in all production modes, the t-, the s- and the tW-channels. Furthermore, I will present recent measurements of top quark properties as well as searches for anomalous couplings ...

  9. Stability of heterodyne terahertz receivers

    NARCIS (Netherlands)

    Kooi, J.W.; Baselmans, J.J.A.; Baryshev, A.; Schieder, R.; Hajenius, M.; Gao, J.R.; Klapwijk, T.M.; Voronov, B.; Gol'tsman, G.

    2006-01-01

    In this paper we discuss the stability of heterodyne terahertz receivers based on small volume NbN phonon cooled hot electron bolometers (HEBs). The stability of these receivers can be broken down in two parts: the intrinsic stability of the HEB mixer and the stability of the local oscillator (LO)

  10. High Gain Advanced GPS Receiver

    National Research Council Canada - National Science Library

    Brown, Alison; Zhang, Gengsheng

    2006-01-01

    NAVSYS High Gain Advanced GPS Receiver (HAGR) uses a digital beam-steering antenna array to enable up to eight GPS satellites to be tracked, each with up to 10 dBi of additional antenna gain over a conventional receiver solution...

  11. Nuclear Power Engineering Education Program, University of Illinois

    International Nuclear Information System (INIS)

    Jones, B.G.

    1993-01-01

    The DOE/CECo Nuclear Power Engineering Education Program at the University of Illinois in its first year has significantly impacted the quality of the power education which our students receive. It has contributed to: the recently completed upgrade of the console of our Advanced TRIGA reactor which increases the reactor's utility for training, the procurement of new equipment to upgrade and refurbish several of the undergraduate laboratory set-ups, and the procurement of computational workstations in support of the instructional computing laboratory. In addition, smaller amounts of funds were used for the recruitment and retention of top quality graduate students, the support of faculty to visit other institutions to attract top students into the discipline, and to provide funds for faculty to participate in short courses to improve their skills and background in the power area. These items and activities have helped elevate in the student's perspective the role of nuclear power in the discipline. We feel this is having a favorable impact on student career selection and on ensuring the continued supply of well educated nuclear engineering graduates

  12. UWB delay and multiply receiver

    Energy Technology Data Exchange (ETDEWEB)

    Dallum, Gregory E.; Pratt, Garth C.; Haugen, Peter C.; Romero, Carlos E.

    2013-09-10

    An ultra-wideband (UWB) delay and multiply receiver is formed of a receive antenna; a variable gain attenuator connected to the receive antenna; a signal splitter connected to the variable gain attenuator; a multiplier having one input connected to an undelayed signal from the signal splitter and another input connected to a delayed signal from the signal splitter, the delay between the splitter signals being equal to the spacing between pulses from a transmitter whose pulses are being received by the receive antenna; a peak detection circuit connected to the output of the multiplier and connected to the variable gain attenuator to control the variable gain attenuator to maintain a constant amplitude output from the multiplier; and a digital output circuit connected to the output of the multiplier.

  13. 5 CFR 1312.27 - Top secret control.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Top secret control. 1312.27 Section 1312... Classified Information § 1312.27 Top secret control. The EOP Security Officer serves as the Top Secret... Top Secret material. The ATSCOs will be responsible for the accountability and custodianship of Top...

  14. The Stirling engine mechanism optimization

    Directory of Open Access Journals (Sweden)

    Jiří Podešva

    2016-03-01

    Full Text Available A special type of the gas engine with external combustion is called Stirling engine. The mechanism has two pistons with two volumes inside. The pistons are connected together through cooler, regenerator and warmer. The engine effectivity depends on the piston movement behaviour. The usual sinusoidal time curve leads to low effectiveness. The quick movement from lower to upper position with a certain delay in both top and bottom dead centres is more effective. The paper deals with three types of mechanisms, analyzing the piston movement, and their behavior. Special emphasize is taken to the piston movement regime.

  15. Prediction of top oil temperature for transformers

    Science.gov (United States)

    He, Qing

    2000-11-01

    When a transformer's winding gets too hot, either the load has to be reduced as a short-term solution or another transformer bay needs to be installed as a long-term plan. To decide on whether to deploy either of these two strategies, one should be able to predict the transformer temperature accurately. In this work, the traditional top-oil-rise model, top-oil model (which includes an ambient temperature) and semi-physical top-oil model are compared. The semi-physical top-oil model outperforms the other two models. Several attempts are also reported to improve the model used for top-oil temperature (TOT) prediction. It is shown that regardless of the order or complexity of the model, no model performs significantly better than the semi-physical top-oil model investigated; moreover, many models have performance measures that are approximately the same as the semi-physical model. Some of the sources of error that affect top-oil temperature prediction are studied here. Experimentation with various discretization schemes and models convinces the author that the semi-physical top-oil model used to predict transformer temperature is near optimal and that other sources of input-data error are frustrating the author's attempt to reduce the prediction error Further. The research demonstrates that the input error caused by database quantization, remote ambient temperature monitoring and low sampling rate accounts for about two-thirds of the error experienced with field data. The results of these simulations also show that the error caused by these sources is less than that obtained when using equivalent field data. It is the opinion of the author that most of this difference is due to the absence of significant driving variables, rather than the approximation used in constructing a semi-physical model. To further improve the error performance of the semi-physical top-oil model, three different neural network models including static neural network, temporal processing network

  16. Customizable Digital Receivers for Radar

    Science.gov (United States)

    Moller, Delwyn; Heavey, Brandon; Sadowy, Gregory

    2008-01-01

    Compact, highly customizable digital receivers are being developed for the system described in 'Radar Interferometer for Topographic Mapping of Glaciers and Ice Sheets' (NPO-43962), NASA Tech Briefs, Vol. 31, No. 7 (August 2007), page 72. The receivers are required to operate in unison, sampling radar returns received by the antenna elements in a digital beam-forming (DBF) mode. The design of these receivers could also be adapted to commercial radar systems. At the time of reporting the information for this article, there were no commercially available digital receivers capable of satisfying all of the operational requirements and compact enough to be mounted directly on the antenna elements. A provided figure depicts the overall system of which the digital receivers are parts. Each digital receiver includes an analog-to-digital converter (ADC), a demultiplexer (DMUX), and a field-programmable gate array (FPGA). The ADC effects 10-bit band-pass sampling of input signals having frequencies up to 3.5 GHz. The input samples are demultiplexed at a user-selectable rate of 1:2 or 1:4, then buffered in part of the FPGA that functions as a first-in/first-out (FIFO) memory. Another part of the FPGA serves as a controller for the ADC, DMUX, and FIFO memory and as an interface between (1) the rest of the receiver and (2) a front-panel data port (FPDP) bus, which is an industry-standard parallel data bus that has a high data-rate capability and multichannel configuration suitable for DBF. Still other parts of the FPGA in each receiver perform signal-processing functions. The digital receivers can be configured to operate in a stand-alone mode, or in a multichannel mode as needed for DBF. The customizability of the receiver makes it applicable to a broad range of system architectures. The capability for operation of receivers in either a stand-alone or a DBF mode enables the use of the receivers in an unprecedentedly wide variety of radar systems.

  17. Anterior Cingulate Cortex Input to the Claustrum Is Required for Top-Down Action Control

    Directory of Open Access Journals (Sweden)

    Michael G. White

    2018-01-01

    Full Text Available Summary: Cognitive abilities, such as volitional attention, operate under top-down, executive frontal cortical control of hierarchically lower structures. The circuit mechanisms underlying this process are unresolved. The claustrum possesses interconnectivity with many cortical areas and, thus, is hypothesized to orchestrate the cortical mantle for top-down control. Whether the claustrum receives top-down input and how this input may be processed by the claustrum have yet to be formally tested, however. We reveal that a rich anterior cingulate cortex (ACC input to the claustrum encodes a preparatory top-down information signal on a five-choice response assay that is necessary for optimal task performance. We further show that ACC input monosynaptically targets claustrum inhibitory interneurons and spiny glutamatergic projection neurons, the latter of which amplify ACC input in a manner that is powerfully constrained by claustrum inhibitory microcircuitry. These results demonstrate ACC input to the claustrum is critical for top-down control guiding action. : White et al. show that anterior cingulate cortex (ACC input to the claustrum encodes a top-down preparatory signal on a 5-choice response assay that is critical for task performance. Claustrum microcircuitry amplifies top-down ACC input in a frequency-dependent manner for eventual propagation to the cortex for cognitive control of action. Keywords: 5CSRTT, optogenetics, fiber photometry, microcircuit, attention, bottom-up, sensory cortices, motor cortices

  18. Waste Receiving and Processing (WRAP) Weight Scale Analysis Results

    International Nuclear Information System (INIS)

    JOHNSON, M.D.

    2000-01-01

    Fairbanks Weight Scales are used at the Waste Receiving and Processing (WRAP) facility to determine the weight of waste drums as they are received, processed, and shipped. Due to recent problems, discovered during calibration, the WRAP Engineering Department has completed this document which outlines both the investigation of the infeed conveyor scale failure in September of 1999 and recommendations for calibration procedure modifications designed to correct deficiencies in the current procedures

  19. Fundamental about energy-efficient set-top boxes; Grundlagen zur Energieeffizienz von Set-Top Boxen

    Energy Technology Data Exchange (ETDEWEB)

    Grieder, T.; Huser, A.

    2004-07-01

    In various countries within Europe, digital television has already achieved a wide distribution. All types of reception are affected by this new technology, cable television, satellite reception and reception with a conventional roof or room aerial. In addition to the television set itself, a separate receiver is required for the digital signals, a so-called set-top box. Instead of one analogue programme, at least 3, or, in extreme cases more than 10, digital programmes are received, with interactive ser-vices also being possible. Up to now, very little of this development has been seen in Switzerland. Thanks to the wide range of programmes available over the cable networks, there is virtually no demand for an improved offer via a conventional aerial. Only in the case of satellite reception has the changeover already taken place in the majority of cases. Attractive additional services, as well as the integration into the international environment, will result in an increasing number of set-top boxes also being used in Switzerland. Over the next 10 to 15 years, the current number of approximately 420,000 units will increase to over 3 million, whereby the total electricity demand within Switzerland will increase by a further 0.5 to 1%. In order to check this increase, the European Union has taken the path of a voluntary agreement with the appliance manufacturers and service providers, and a similar procedure is also recommended for Switzerland. In addition, this study also draws up various recommendations for the importers of set-top boxes and for the service providers. (author)

  20. Top-philic scalar Dark Matter with a vector-like fermionic top partner

    OpenAIRE

    Baek, Seungwon; Ko, Pyungwon; Wu, Peiwen

    2016-01-01

    We consider a simple extension of the Standard Model with a scalar top-philic Dark Matter (DM) $S$ coupling, apart from the Higgs portal, exclusively to the right-handed top quark $t_R$ and a colored vector-like top partner $T$ with a Yukawa coupling $y_{ST}$ which we call the topVL portal. When the Higgs portal is closed and $y_{ST}$ is perturbative $ (\\lesssim 1)$, $TS\\to (W^+b, gt)$, $SS\\to t\\bar{t}$ and $T\\bar{T}\\to (q\\bar{q},gg)$ provide the dominant (co)annihilation contributions to obt...

  1. 78 FR 38957 - Agency Information Collection Activities; Comment Request; Race to the Top-Early Learning...

    Science.gov (United States)

    2013-06-28

    ... demonstrates that high-quality early learning and development programs and services can improve young children...; Comment Request; Race to the Top--Early Learning Challenge Annual Performance Report AGENCY: Office of... the use of information technology. Please note that written comments received in response to this...

  2. The relevance of surveying content in mining engineering education ...

    African Journals Online (AJOL)

    The University of the Witwatersrand School of Mining Engineering (Wits Mining) has its origins in the South African School of Mines, which was established in 1896. It is currently recognised as one of the world's top mining engineering schools that educate mining engineering candidates to become qualified to specialise in ...

  3. Highly efficient 6-stroke engine cycle with water injection

    Science.gov (United States)

    Szybist, James P; Conklin, James C

    2012-10-23

    A six-stroke engine cycle having improved efficiency. Heat is recovered from the engine combustion gases by using a 6-stroke engine cycle in which combustion gases are partially vented proximate the bottom-dead-center position of the fourth stroke cycle, and water is injected proximate the top-dead-center position of the fourth stroke cycle.

  4. Single top quarks and dark matter

    Science.gov (United States)

    Pinna, Deborah; Zucchetta, Alberto; Buckley, Matthew R.; Canelli, Florencia

    2017-08-01

    Processes with dark matter interacting with the standard model fermions through new scalars or pseudoscalars with flavor-diagonal couplings proportional to fermion mass are well motivated theoretically, and provide a useful phenomenological model with which to interpret experimental results. Two modes of dark matter production from these models have been considered in the existing literature: pairs of dark matter produced through top quark loops with an associated monojet in the event, and pair production of dark matter with pairs of heavy flavored quarks (tops or bottoms). In this paper, we demonstrate that a third, previously overlooked channel yields a non-negligible contribution to LHC dark matter searches in these models. In spite of a generally lower production cross section at LHC when compared to the associated top-pair channel, non-flavor violating single top quark processes are kinematically favored and can significantly increase the sensitivity to these models. Including dark matter production in association with a single top quark through scalar or pseudoscalar mediators, the exclusion limit set by the LHC searches for dark matter can be improved by 30% up to a factor of two, depending on the mass assumed for the mediator particle.

  5. Monotop signature from a fermionic top partner

    Science.gov (United States)

    Gonçalves, Dorival; Kong, Kyoungchul; Sakurai, Kazuki; Takeuchi, Michihisa

    2018-01-01

    We investigate monotop signatures arising from phenomenological models of fermionic top partners, which are degenerate in mass and decay into a bosonic dark matter candidate, either spin 0 or spin 1. Such a model provides a monotop signature as a smoking gun, while conventional searches with t t ¯ + missing transverse momentum are limited. Two such scenarios, (i) a phenomenological third generation extradimensional model with excited top and electroweak sectors, and (ii) a model where only a top partner and a dark matter particle are added to the standard model, are studied in the degenerate mass regime. We find that in the case of extra dimension a number of different processes give rise to effectively the same monotop final state, and a great gain can be obtained in the sensitivity for this channel. We show that the monotop search can explore top-partner masses up to 630 and 300 GeV for the third generation extradimensional model and the minimal fermionic top-partner model, respectively, at the high luminosity LHC.

  6. Top physics at CLIC and ILC

    CERN Document Server

    AUTHOR|(SzGeCERN)442572

    2016-11-11

    Measurements of top quark production at $e^+e^-$ colliders can provide a leap in precision in our knowledge of top quark properties and open a new window on physics beyond the Standard Model. In this contribution the top quark physics prospects of linear colliders is reviewed. Progress in detailed full-simulation studies is reported for the highlights of the program. We present the prospects for a measurement of the top quark mass and width in a scan of the beam energy through the pair production threshold, and discuss new studies of alternative measurements in continuum production, which are also capable of a precise determination of the mass in a rigorously defined mass scheme. A precision of 50 MeV on the $\\overline{MS}$ mass is expected when taking into account the dominant systematic uncertainties. Another key measurement is the study of the top quark couplings to electroweak gauge bosons, where form factors can be determined to 1% precision, an order of magnitude better than those from the full LHC prog...

  7. Engineering opportunities in nuclear engineering

    International Nuclear Information System (INIS)

    Walton, D.G.

    1980-01-01

    The pattern of education and training of Nuclear Engineers in the UK is outlined under the headings; degree courses for professional engineers, postgraduate courses, education of technician engineers. Universities which offer specific courses are stated and useful addresses listed. (UK)

  8. D-Zero top quark mass analysis

    International Nuclear Information System (INIS)

    Strovink, M.

    1996-10-01

    I report on D null's preliminary analyses of the top quark mass m t based on an exposure at √s = 1.8 TeV with integrated luminosity ∼100 pb -1 at the Fermilab Tevatron p anti p collider. From three e + μ + ≥ 2 jet events (with background 0.36 ± 0.09), using partly original methods, we obtain m t = 158 ± 24(stat) ± 10(syst) GeV/c 2 . From 30 e or μ + ±4 jets events (with background 17.4 ±2.2), we find m t = 170 ± 15(stat) ± 10(syst) GeV/c 2 . Recently, using multivariate methods based on particular kinematic variables, we have learned how to improve the background suppression in the latter sample without unduly distorting the reconstructed top mass spectra. Applying these methods should improve considerably the accuracy of our top quark mass determination

  9. Workshop: Waiting for the top quark

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    The world of elementary particle physics is eagerly waiting for the top quark, probably the final element of the 'periodic table' of elementary particle constituents. This table consists of two families of weakly interacting particles (leptons) - one series carrying electric charge; the other being electrically neutral - together with a family of quarks carrying electric charge 2/3 (up, charm, top) and a family of charge -1/3 quarks (down, strange, beauty). It was then not surprising that the 1990 Theory Workshop at the DESY Laboratory in Hamburg in October, devoted this time to 'top physics', attracted some 200 physicists, substantially more than previous workshops in the series

  10. Top quark physics in ATLAS (CORFU 2014)

    CERN Document Server

    Moreno Llácer, M; The ATLAS collaboration

    2014-01-01

    The top quark is the heaviest elementary particle observed to date. Being heavier than a W boson, it is the only quark that decays weakly, i.e. into a real W boson and a b quark, before hadronization can occur. In addition, it is the only quark whose Yukawa coupling to the Higgs boson is order of unity. For these reasons the top quark plays a special role in the Standard Model of Particle Physics and in many of its extensions. An accurate knowledge of its properties (mass, couplings, production cross section, decay branching ratios, etc.) can bring key information on fundamental interactions at the electroweak breaking scale and beyond. In this talk the latest measurements of the characteristics of the top quark carried out in the ATLAS experiment at the Large Hadron Collider are presented.

  11. Anomalous creation and decay of top quarks

    CERN Document Server

    Hasegawa, S; The ATLAS collaboration

    2012-01-01

    Due to the top quark’s mass of 173.5 GeV/c2 which is around the energy scale of the spon- taneous symmetry breaking, appearance of new physics can be expected in its production and decay as an anomaly from the standard model expectation. The ATLAS and the CMS experiments have accumulated about 5 fb−1 of data of proton-proton collisions with 7 TeV center of mass energy in 2011, in which 800,000 top quarks pairs are expected. With this high statistics, the ATLAS and the CMS collaborations have investigated the top quark’s production and decay precisely and have reported the results consistent with the standard model.

  12. TOP PRIORITI QMS PRINCIPLES FOR ACHIEVING BUSINESS EXCELLENCE

    Directory of Open Access Journals (Sweden)

    Aleksandar Vujović

    2010-06-01

    Full Text Available The main target of this paper is to select top priority principles of QMS for achieving business excellence. This could be done from the standpoint of significant of principles. That means that. organization should make more attention to this principles in the way for making excellent results. This paper has been developed as a tendency of researchers in the Center for quality-Faculty of mechanical engineering in Podgorica to establish a model for improvement of business processes performances based on quality management system through comparison with top organizational performances characterized by criteria i.e. particularities of the business excellence model. Correlation of principles of the quality management system with QMS principles has been established to that effect. Weight coefficients have been also determined for each principle individually. Thereby key principles were identified, namely priorities in terms of achieving business excellence i.e. areas (principles were given priorities, that is to say principles that play the biggest part in achieving business excellence.

  13. PASS: a component of Desk Top PA for the WIPP

    International Nuclear Information System (INIS)

    Crawford, M.B.; Wilmot, R.D.; Galson, D.A.; Swift, P.N.; Fewell, M.E.

    1998-01-01

    There is a growing recognition internationally of the need to demonstrate comprehensiveness in order to build confidence in performance assessments (PAs) for radioactive waste disposal projects. This has resulted in a number of methodologies being developed to formalize the process of defining and documenting the decision basis that underlies a PA. Such methodologies include process influence diagrams and the rock engineering system (RES) matrix. However, these methodologies focus mainly on the conceptualization of the disposal system and do not provide a ready framework to document the decisions behind the model development and parameterization of the PA system. The Performance Assessment Support System (PASS) is a flexible electronic tool designed to increase the transparency and traceability of decision making in the entire PA process. An application of PASS has been developed for the Waste Isolation Pilot Plant (WIPP) where it forms an important component of Desk Top PA, a PC-based PA computational environment under development at Sandia National Laboratories to document, plan, and support management decisions and to assess performance for the WIPP recertification process. This desk-top PA environment is also aimed at providing scientifically-based decision support for assessing the performance of nuclear and hazardous waste management and environmental clean-up systems

  14. HIGH-EFFICIENCY INFRARED RECEIVER

    Directory of Open Access Journals (Sweden)

    A. K. Esman

    2016-01-01

    Full Text Available Recent research and development show promising use of high-performance solid-state receivers of the electromagnetic radiation. These receivers are based on the low-barrier Schottky diodes. The approach to the design of the receivers on the basis of delta-doped low-barrier Schottky diodes with beam leads without bias is especially actively developing because for uncooled receivers of the microwave radiation these diodes have virtually no competition. The purpose of this work is to improve the main parameters and characteristics that determine the practical relevance of the receivers of mid-infrared electromagnetic radiation at the operating room temperature by modifying the electrodes configuration of the diode and optimizing the distance between them. Proposed original design solution of the integrated receiver of mid-infrared radiation on the basis of the low-barrier Schottky diodes with beam leads allows to effectively adjust its main parameters and characteristics. Simulation of the electromagnetic characteristics of the proposed receiver by using the software package HFSS with the basic algorithm of a finite element method which implemented to calculate the behavior of electromagnetic fields on an arbitrary geometry with a predetermined material properties have shown that when the inner parts of the electrodes of the low-barrier Schottky diode is performed in the concentric elliptical convex-concave shape, it can be reduce the reflection losses to -57.75 dB and the standing wave ratio to 1.003 while increasing the directivity up to 23 at a wavelength of 6.09 μm. At this time, the rounded radii of the inner parts of the anode and cathode electrodes are equal 212 nm and 318 nm respectively and the gap setting between them is 106 nm. These parameters will improve the efficiency of the developed infrared optical-promising and electronic equipment for various purposes intended for work in the mid-infrared wavelength range. 

  15. Low emission internal combustion engine

    Science.gov (United States)

    Karaba, Albert M.

    1979-01-01

    A low emission, internal combustion compression ignition engine having a cylinder, a piston movable in the cylinder and a pre-combustion chamber communicating with the cylinder near the top thereof and in which low emissions of NO.sub.x are achieved by constructing the pre-combustion chamber to have a volume of between 70% and 85% of the combined pre-chamber and main combustion chamber volume when the piston is at top dead center and by variably controlling the initiation of fuel injection into the pre-combustion chamber.

  16. Math, Science, and Engineering Integration in a High School Engineering Course: A Qualitative Study

    Science.gov (United States)

    Valtorta, Clara G.; Berland, Leema K.

    2015-01-01

    Engineering in K-12 classrooms has been receiving expanding emphasis in the United States. The integration of science, mathematics, and engineering is a benefit and goal of K-12 engineering; however, current empirical research on the efficacy of K-12 science, mathematics, and engineering integration is limited. This study adds to this growing…

  17. Optimal Taxation, Inequality and Top Incomes

    OpenAIRE

    Andrienko, Yuri; Apps, Patricia; Rees, Ray

    2014-01-01

    In a number of high-income countries over the past few decades there has been a large growth in income inequality and at the same time a shift in the burden of taxation from the top to the middle of the income distribution. This paper applies the theory of optimal piecewise linear taxation to the issue of the taxation of top incomes. Our results suggest that an appropriate response to rising inequality is a shift towards a more progressive multi-bracket income tax system, with a more differen...

  18. Boosted top production in ATLAS and CMS

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00237277; The ATLAS collaboration

    2017-01-01

    An overview of the boosted top production analyses using data collected by the ATLAS and CMS experiments at $\\sqrt{s}=$' 8 TeV and 13 TeV of proton-proton collisions at the LHC is presented. These analyses use techniques for the reconstruction of boosted objects to measure the production of top quarks at high transverse momenta. The measurements are optimized for the different final states and for different ranges of the transverse momenta of the particles involved, improving on measurements with traditional objects reconstruction based on the combination of resolved objects.

  19. New multigrid solver advances in TOPS

    International Nuclear Information System (INIS)

    Falgout, R D; Brannick, J; Brezina, M; Manteuffel, T; McCormick, S

    2005-01-01

    In this paper, we highlight new multigrid solver advances in the Terascale Optimal PDE Simulations (TOPS) project in the Scientific Discovery Through Advanced Computing (SciDAC) program. We discuss two new algebraic multigrid (AMG) developments in TOPS: the adaptive smoothed aggregation method (αSA) and a coarse-grid selection algorithm based on compatible relaxation (CR). The αSA method is showing promising results in initial studies for Quantum Chromodynamics (QCD) applications. The CR method has the potential to greatly improve the applicability of AMG

  20. TOP500 Supercomputers for November 2003

    Energy Technology Data Exchange (ETDEWEB)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2003-11-16

    22nd Edition of TOP500 List of World s Fastest Supercomputers Released MANNHEIM, Germany; KNOXVILLE, Tenn.; BERKELEY, Calif. In what has become a much-anticipated event in the world of high-performance computing, the 22nd edition of the TOP500 list of the worlds fastest supercomputers was released today (November 16, 2003). The Earth Simulator supercomputer retains the number one position with its Linpack benchmark performance of 35.86 Tflop/s (''teraflops'' or trillions of calculations per second). It was built by NEC and installed last year at the Earth Simulator Center in Yokohama, Japan.

  1. Understanding microelectronics a top-down approach

    CERN Document Server

    Maloberti, Franco

    2011-01-01

    The microelectronics evolution has given rise to many modern benefits but has also changed design methods and attitudes to learning. Technology advancements shifted focus from simple circuits to complex systems with major attention to high-level descriptions. The design methods moved from a bottom-up to a top-down approach. For today's students, the most beneficial approach to learning is this top-down method that demonstrates a global view of electronics before going into specifics. Franco Maloberti uses this approach to explain the fundamentals of electronics, such as processing functions,

  2. W/Top/Higgs-tagging in ATLAS

    CERN Document Server

    Norjoharuddeen, Nurfikri; The ATLAS collaboration

    2017-01-01

    We present updates of W, Top and Higgs tagging studies with the ATLAS detector. The performance of 2 variable taggers, HEPTopTagger and shower deconstruction are compared in Monte Carlo simulations. To asses the modelling of the taggers’ performance, the tagging efficiencies are measured, with the full 2015+2016 dataset, in semi-leptonic top quark pair events and the background rejections are measured in dijet and photon+jet topologies. Recent developments in subjet reconstruction techniques for high transverse momentum Higgs->bb tagging are also presented.

  3. TopN-Pareto Front Search

    Energy Technology Data Exchange (ETDEWEB)

    2016-12-21

    The JMP Add-In TopN-PFS provides an automated tool for finding layered Pareto front to identify the top N solutions from an enumerated list of candidates subject to optimizing multiple criteria. The approach constructs the N layers of Pareto fronts, and then provides a suite of graphical tools to explore the alternatives based on different prioritizations of the criteria. The tool is designed to provide a set of alternatives from which the decision-maker can select the best option for their study goals.

  4. Recent Results on Top Physics in CMS

    CERN Multimedia

    CERN. Geneva

    2012-01-01

    Top physics is a pillar of the physics programme at the LHC. It involves precision measurements, leading to constraints on standard model parameters, as well as many measurements of observables sensitive to new physics. In this seminar, an overview of measurements performed by the CMS experiment in the domain of top physics will be presented, based on pp data collected in 2011 at a center-of-mass energy of 7 TeV. The results will be compared to expectations from theory. Emphasis in will be given to more recent results and to the treatment of systematic uncertainties.

  5. Top and Electroweak Measurements at the Tevatron

    Energy Technology Data Exchange (ETDEWEB)

    Bartos, P. [Comenius U.

    2016-01-01

    In this report, we summarize the latest results of the top-quark mass and electroweak measurements from the Tevatron. Since the world combination of top-quark mass measurements was done, CDF and D0 experiments improved the precision of several results. Some of them reach the relative precition below 1% for a single measurement. From the electroweak results, we report on the WW and WZ production cross section, measurements of the weak mixing angle and indirect measurements of W boson mass. The Tevatron results of the weak mixing angle are still the most precise ones of hadron colliders.

  6. Single top quark production at LEP200?

    International Nuclear Information System (INIS)

    Boos, E.; Ishikawa, T.; Kaneko, T.; Kawabata, S.; Kurihara, Y.; Shimizu, Y.; Tanaka, H.

    1994-01-01

    A complete tree-level calculation of the reaction e + e - → e + ν e anti tb (e - anti ν e t anti b) in the electroweak standard theory in the LEP200 energy range is presented. For top quark masses in the range 130 to 190 GeV the cross sections are found to be in the order of 10 -5 to 10 -6 pb. Therefore, the number of single top quark events is expected to be negligible even with an integrated luminosity of L = 500 pb -1 . It is further demonstrated that the Weizsaecker-Williams approximation is approaching the accurate cross section calculations resonably well. (orig.)

  7. Lepton distribution in top decay: A probe of new physics and top ...

    Indian Academy of Sciences (India)

    it may become difficult to probe new physics couplings of top quark. However, if one can construct observables that are sensitive to production and decay mecha- nism independent of each other, the analysis can be greatly simplified. It has been shown that the angular distribution of the leptons from the decay of top quark is.

  8. An Efficiency Comparison of MBA Programs: Top 10 versus Non-Top 10

    Science.gov (United States)

    Hsu, Maxwell K.; James, Marcia L.; Chao, Gary H.

    2009-01-01

    The authors compared the cohort group of the top-10 MBA programs in the United States with their lower-ranking counterparts on their value-added efficiency. The findings reveal that the top-10 MBA programs in the United States are associated with statistically higher average "technical and scale efficiency" and "scale efficiency", but not with a…

  9. NASA Software Engineering Benchmarking Study

    Science.gov (United States)

    Rarick, Heather L.; Godfrey, Sara H.; Kelly, John C.; Crumbley, Robert T.; Wifl, Joel M.

    2013-01-01

    was its software assurance practices, which seemed to rate well in comparison to the other organizational groups and also seemed to include a larger scope of activities. An unexpected benefit of the software benchmarking study was the identification of many opportunities for collaboration in areas including metrics, training, sharing of CMMI experiences and resources such as instructors and CMMI Lead Appraisers, and even sharing of assets such as documented processes. A further unexpected benefit of the study was the feedback on NASA practices that was received from some of the organizations interviewed. From that feedback, other potential areas where NASA could improve were highlighted, such as accuracy of software cost estimation and budgetary practices. The detailed report contains discussion of the practices noted in each of the topic areas, as well as a summary of observations and recommendations from each of the topic areas. The resulting 24 recommendations from the topic areas were then consolidated to eliminate duplication and culled into a set of 14 suggested actionable recommendations. This final set of actionable recommendations, listed below, are items that can be implemented to improve NASA's software engineering practices and to help address many of the items that were listed in the NASA top software engineering issues. 1. Develop and implement standard contract language for software procurements. 2. Advance accurate and trusted software cost estimates for both procured and in-house software and improve the capture of actual cost data to facilitate further improvements. 3. Establish a consistent set of objectives and expectations, specifically types of metrics at the Agency level, so key trends and models can be identified and used to continuously improve software processes and each software development effort. 4. Maintain the CMMI Maturity Level requirement for critical NASA projects and use CMMI to measure organizations developing software for NASA. 5

  10. United States Department of Energy solar receiver technology development

    Science.gov (United States)

    Klimas, P. C.; Diver, R. B.; Chavez, J. M.

    The United States Department of Energy (DOE), through Sandia National Laboratories, has been conducting a Solar Thermal Receiver Technology Development Program, which maintains a balance between analytical modeling, bench and small scale testing, and experimentation conducted at scales representative of commercially-sized equipment. Central receiver activities emphasize molten salt-based systems on large scales and volumetric devices in the modeling and small scale testing. These receivers are expected to be utilized in solar power plants rated between 100 and 200 MW. Distributed receiver research focuses on liquid metal refluxing devices. These are intended to mate parabolic dish concentrators with Stirling cycle engines in the 5 to 25 kW(sub e) power range. The effort in the area of volumetric receivers is less intensive and highly cooperative in nature. A ceramic foam absorber of Sandia design was successfully tested on the 200 kW(sub t) test bed at Plataforma Solar during 1989. Material integrity during the approximately 90-test series was excellent. Significant progress has been made with parabolic dish concentrator-mounted receivers using liquid metals (sodium or a potassium/sodium mixture) as heat transport media. Sandia has successfully solar-tested a pool boiling reflux receiver sized to power a 25 kW Stirling engine. Boiling stability and transient operation were both excellent. This document describes these activities in detail and will outline plans for future development.

  11. Engineering Institute

    Science.gov (United States)

    Projects Past Projects Publications NSEC » Engineering Institute Engineering Institute Multidisciplinary engineering research that integrates advanced modeling and simulations, novel sensing systems and new home of Engineering Institute Contact Institute Director Charles Farrar (505) 665-0860 Email UCSD EI

  12. Determination of the top-quark mass from hadro-production of single top-quarks

    International Nuclear Information System (INIS)

    Alekhin, S.; Moch, S.; Thier, S.

    2016-08-01

    We present a new determination of the top-quark mass m_t based on the experimental data from the Tevatron and the LHC for single-top hadro-production. We use the inclusive cross sections of s- and t-channel top-quark production to extract m_t and to minimize the dependence on the strong coupling constant and the gluon distribution in the proton compared to the hadro-production of top-quark pairs. As part of our analysis we compute the next-to-next-to-leading order approximation for the s-channel cross section in perturbative QCD based on the known soft-gluon corrections and implement it in the program HatHor for the numerical evaluation of the hadronic cross section. Results for the top-quark mass are reported in the MS and in the on-shell renormalization scheme.

  13. Morel Receives 2005 Maurice Ewing Medal

    Science.gov (United States)

    Schrag, Daniel P.; Morel, François M. M.

    2006-02-01

    François M. M. Morel received the Ewing Medal at the AGU Fall Meeting Honors Ceremony, which was held on 7 December 2005, in San Francisco, Calif. The medal is given for significant original contributions to the scientific understanding of the processes in the ocean; for the advancement of oceanographic engineering, technology, and instrumentation; and for outstanding service to marine sciences. François Morel has led the search to understand the role of metals in the ocean, starting with a focus on inorganic processes and aquatic chemistry, and leading to a blend of geochemistry, microbiology, biochemistry, and genetics. His influence comes from his research and from the way he has educated an entire community of scientists with his textbooks, with his teaching, and through his former students and postdocs who hold faculty positions at universities throughout the world.

  14. Game engine architecture

    CERN Document Server

    Gregory, Jason

    2014-01-01

    ""… this book is the best of its kind, and you're lucky to have found it. It covers the huge field of game engine architecture in a succinct, clear way, and expertly balances the breadth and depth of its coverage, offering enough detail that even a beginner can easily understand the concepts it presents. The author, Jason Gregory, is not only a world expert in his field; he's a working programmer with production-quality knowledge and many shipped game projects under his belt. … Jason is also an experienced educator who has taught in the top-ranked university game program in North America. …

  15. GIVING AND RECEIVING CONSTRUCTIVE FEEDBACK

    Directory of Open Access Journals (Sweden)

    Ірина Олійник

    2015-05-01

    Full Text Available The article scrutinizes the notion of feedback applicable in classrooms where team teaching is provided. The experience of giving and receiving feedback has been a good practice in cooperation between a U.S. Peace Corps volunteer and a Ukrainian counterpart. Giving and receiving feedback is an effective means of classroom observation that provides better insight into the process of teaching a foreign language. The article discusses the stages of feedback and explicates the notion of sharing experience between two teachers working simultaneously in the same classroom. The guidelines for giving and receiving feedback have been provided as well as the most commonly used vocabulary items have been listed. It has been proved that mutual feedback leads to improving teaching methods and using various teaching styles and techniques.

  16. Receiver-exciter controller design

    Science.gov (United States)

    Jansma, P. A.

    1982-01-01

    A description of the general design of both the block 3 and block 4 receiver-exciter controllers for the Deep Space Network (DSN) Mark IV-A System is presented along with the design approach. The controllers are designed to enable the receiver-exciter subsystem (RCV) to be configured, calibrated, initialized and operated from a central location via high level instructions. The RECs are designed to be operated under the control of the DMC subsystem. The instructions are in the form of standard subsystem blocks (SSBs) received via the local area network (LAN). The centralized control provided by RECs and other DSCC controllers in Mark IV-A is intended to reduce DSN operations costs from the Mark III era.

  17. Beef customer satisfaction: USDA quality grade and marination effects on consumer evaluations of top round steaks.

    Science.gov (United States)

    Behrends, J M; Goodson, K J; Koohmaraie, M; Shackelford, S D; Wheeler, T L; Morgan, W W; Reagan, J O; Gwartney, B L; Wise, J W; Savell, J W

    2005-03-01

    An in-home beef study evaluated consumer ratings of top round steaks (semimembranosus) as influenced by USDA quality grade (top Choice or high Select), city (Chicago or Philadelphia), consumer segment (beef loyalists = heavy consumers of beef; budget rotators = cost-driven and split meat consumption between beef and chicken; and variety rotators = higher incomes and education and split meat consumption among beef, poultry, and other foods), degree of doneness, cooking method, and marination. Consumers evaluated each steak for overall like, tenderness, juiciness, flavor like, and flavor amount using 10-point scales (1 = dislike extremely, not at all tender, not at all juicy, dislike extremely, and none at all to 10 = like extremely, extremely tender, extremely juicy, like extremely, and an extreme amount of flavor, respectively). Quality grade affected several consumer sensory traits, with top Choice receiving higher (P Consumers in Chicago rated steaks cooked "medium and less" higher for overall like, tenderness, juiciness, flavor like, and flavor amount than those in Philadelphia (city x degree of doneness; P customers in Philadelphia received among the highest scores for overall like, tenderness, juiciness, flavor like, and flavor amount compared with any cooking method used by customers in Chicago (cooking method x city; P customers' satisfaction with top round steaks, and was the sensory trait most highly correlated to overall like, followed by tenderness, flavor amount, and juiciness. Preparation of top round steaks was crucial in consumers' likes and dislikes, and by improving flavor, higher consumer satisfaction may be achieved.

  18. Mechanical engineering

    CERN Document Server

    Darbyshire, Alan

    2010-01-01

    Alan Darbyshire's best-selling text book provides five-star high quality content to a potential audience of 13,000 engineering students. It explains the most popular specialist units of the Mechanical Engineering, Manufacturing Engineering and Operations & Maintenance Engineering pathways of the new 2010 BTEC National Engineering syllabus. This challenging textbook also features contributions from specialist lecturers, ensuring that no stone is left unturned.

  19. Stability of heterodyne terahertz receivers

    OpenAIRE

    Kooi, J. W.; Baselmans, J. J. A.; Baryshev, A.; Schieder, R.; Hajenius, M.; Gao, J. R.; Klapwijk, T. M.; Voronov, B.; Gol'tsman, G.

    2006-01-01

    In this paper we discuss the stability of heterodyne terahertz receivers based on small volume NbN phonon cooled hot electron bolometers (HEBs). The stability of these receivers can be broken down in two parts: the intrinsic stability of the HEB mixer and the stability of the local oscillator (LO) signal injection scheme. Measurements show that the HEB mixer stability is limited by gain fluctuations with a 1/f spectral distribution. In a 60 MHz noise bandwidth this results in an Allan varian...

  20. Paterson Receives 2004 Walter H. Bucher Medal

    Science.gov (United States)

    Jackson, Ian

    2005-01-01

    Mervyn S. Paterson received the Bucher Medal at the 2004 Fall Meeting Honors Ceremony on 15 December, in San Francisco, California. The medal is given for original contributions to the basic knowledge of the crust and lithosphere. Citation. It is the nature of modern research in the Earth sciences that observations of natural phenomena are often made and interpreted through the prism provided by the enabling sciences and technologies. Thus it has been with Mervyn Paterson's career. His undergraduate training in engineering in Adelaide formed the basis for his Ph.D. study of X-ray line-broadening in cold-worked metals under Orowan at Cambridge. This interest in the deformation of metals was fostered during his employment at the Aeronautical Research Laboratories in Melbourne and by postdoctoral experience at the Institute of Metals at the University of Chicago. Mervyn's general background in engineering and his particular interest in mechanical behavior have underpinned a distinguished career at the Australian National University in the experimental deformation of rocks, providing fundamental new insight into the mechanical behavior of the Earth's crust.

  1. SAT in engineering support personnel training

    International Nuclear Information System (INIS)

    Gonzalez, M.

    1995-01-01

    The NPP engineering support functional area comprises seven common positions: reactor engineer, in-service inspection engineer, performance reliability engineer, system-maintenance engineer, station modification engineer, quality assurance engineer, and regulatory compliance engineer. The primary duties and tasks of each was presented. In Spain, a simplified SAT approach was used to analyze the training needs of these positions. The basic difference between the comprehensive SAT and the simplified method is that the simplified approach uses no taxonomy codes and the task elements are not analyzed to obtain the knowledge and skills. Resulting in an economy of time and personnel resources, this process makes use of job competencies and a top table analysis conducted by subject matter experts. An example of a JPM prepared using the simplified SAT approach was shown. Examples of the simplified approaches used in Russia, France, and USA were also discussed

  2. Model uncertainties in top-quark physics

    CERN Document Server

    Seidel, Markus

    2014-01-01

    The ATLAS and CMS collaborations at the Large Hadron Collider (LHC) are studying the top quark in pp collisions at 7 and 8 TeV. Due to the large integrated luminosity, precision measurements of production cross-sections and properties are often limited by systematic uncertainties. An overview of the modeling uncertainties for simulated events is given in this report.

  3. Learning from Top-Performing Managers.

    Science.gov (United States)

    Brown, Paul L.

    2000-01-01

    Illustrates five criteria that can be used to identify the "best" managers in any organization: business results, employee attitudes, peer confirmation, upper-level manager appraisal, and customer satisfaction. Examines what top-performing managers say and do, and concludes that their thinking processes and their specific sets of skills…

  4. Taking a gamble on the top quark

    International Nuclear Information System (INIS)

    Flam, F.

    1994-01-01

    This article describes the possible discovery of the top quark at Fermilab. Evidence for its existence is now at the level of two standard deviations above background, but a solid claim for discovery will not be made until the probability is five standard deviations. That should require one more year of experimentation

  5. New Physics with Energetic Top Quarks

    CERN Document Server

    Andeen, Timothy; The ATLAS collaboration

    2018-01-01

    Many theories beyond the Standard Model predict new phenomena which decay to energetic top quarks. Searches for such new physics models are performed using the ATLAS experiment at the LHC using proton-proton collision data collected in 2015 and 2016 with a center-of-mass energy of 13 TeV. Selected recent results will be discussed.

  6. Top-Ten IT Issues: 2009

    Science.gov (United States)

    Agee, Anne Scrivener; Yang, Catherine

    2009-01-01

    This article presents the top-ten IT-related issues in terms of strategic importance to the institution, as revealed by the tenth annual EDUCAUSE Current Issues Survey. These IT-related issues include: (1) Funding IT; (2) Administrative/ERP Information Systems; (3) Security; (4) Infrastructure/Cyberinfrastructure; (5) Teaching and Learning with…

  7. Top-down modulation, emotion, and hallucination

    NARCIS (Netherlands)

    Aleman, A; Kahn, RS

    2002-01-01

    We argue that the pivotal role assigned by Northoff to the principle of top-down modulation in catatonia might successfully be applied to other symptoms of schizophrenia, for example, hallucinations. Second, we propose that Northoffs account would benefit from a more comprehensive analysis of the

  8. Top Down proteomics: Facts and perspectives

    Energy Technology Data Exchange (ETDEWEB)

    Catherman, Adam D.; Skinner, Owen S.; Kelleher, Neil L., E-mail: n-kelleher@northwestern.edu

    2014-03-21

    Highlights: • Top Down versus Bottom Up proteomics analysis. • Separations methods for Top Down proteomics. • Developments in mass spectrometry instrumentation and fragmentation. • Native mass spectrometry. - Abstract: The rise of the “Top Down” method in the field of mass spectrometry-based proteomics has ushered in a new age of promise and challenge for the characterization and identification of proteins. Injecting intact proteins into the mass spectrometer allows for better characterization of post-translational modifications and avoids several of the serious “inference” problems associated with peptide-based proteomics. However, successful implementation of a Top Down approach to endogenous or other biologically relevant samples often requires the use of one or more forms of separation prior to mass spectrometric analysis, which have only begun to mature for whole protein MS. Recent advances in instrumentation have been used in conjunction with new ion fragmentation using photons and electrons that allow for better (and often complete) protein characterization on cases simply not tractable even just a few years ago. Finally, the use of native electrospray mass spectrometry has shown great promise for the identification and characterization of whole protein complexes in the 100 kDa to 1 MDa regime, with prospects for complete compositional analysis for endogenous protein assemblies a viable goal over the coming few years.

  9. Measuring the running top-quark mass

    International Nuclear Information System (INIS)

    Langenfeld, Ulrich; Uwer, Peter

    2010-06-01

    In this contribution we discuss conceptual issues of current mass measurements performed at the Tevatron. In addition we propose an alternative method which is theoretically much cleaner and to a large extend free from the problems encountered in current measurements. In detail we discuss the direct determination of the top-quark's running mass from the cross section measurements performed at the Tevatron. (orig.)

  10. Top management motivation in global corporations

    Directory of Open Access Journals (Sweden)

    Dmytro Lukianenko

    2015-11-01

    Full Text Available The article explores economic localization, socialization and development intellectualization processes. The research is focused on the relevant problem implying formation and development of human resources at organizations as a key factor of their competitiveness. Based on generalizing modern theoretical motivational models a comprehensive analysis of the motivation system for top management of corporations within the paradigm of global management has been carried out. Special attention is paid to the phenomenon of global business personification and virtualization, as well as to the formation of new financial and nonfinancial incentives for top managers. Practices of effective incentives for the contemporary key corporate management actors have been studied. A comprehensive country-based comparative analysis of key tools for financial and non-financial corporate incentives for top managers within the system of long-term, short-term and regulatory criteria and parameters has been performed. Based on summarizing academic studies and empirical evidence of the leading multinational corporations a motivational model for top management of corporations has been grounded and suggested for practical implementation in Ukraine with the said model accounting for the corporations' basic needs, financial status and interests as well as for countryspecific and regional features.

  11. Essays on top management and corporate behavior

    NARCIS (Netherlands)

    Wu, H.T.

    2010-01-01

    Human behavior is fascinating, and there is no exception to what its influences are on the financial market. This dissertation consists of three essays that examine corporate behavior that is affected by decisions made by the top management. The first essay studies the rationale for leveraged buyout

  12. Are Female Top Managers Really Paid Less?

    NARCIS (Netherlands)

    Geiler, P.H.M.; Renneboog, L.D.R.

    2014-01-01

    Abstract: Are female top managers paid less than their male counterparts? Is the gender gap higher in male-dominated industries? What effect on pay do female non-executive directors and remuneration consultants exert? While we find no pay gap for the figure-head (CEO), there is strong pay

  13. Are female top managers really paid less?

    NARCIS (Netherlands)

    Geiler, P.H.M.; Renneboog, Luc

    2015-01-01

    We study the gender pay gap for all top managers (CEO and executive directors) of listed UK companies and find mixed evidence: female CEOs do not face a pay gap, but the other female executive directors (e.g. CFO, COO, Deputy CEO) are discriminated against (while controlling for position, tenure,

  14. Top Tagging by Deep Learning Algorithm

    CERN Document Server

    Akil, Ali

    2015-01-01

    In this report I will show the application of a deep learning algorithm on a Monte Carlo simulation sample to test its performance in tagging hadronic decays of boosted top quarks and compare what we get with the results of the application of some other algorithms.

  15. Climate change and marine top predators

    DEFF Research Database (Denmark)

    Climate change affects all components of marine ecosystems. For endothermic top predators, i.e. seabirds and marine mammals, these impacts are often complex and mediated through trophic relationships. In this Research Topic, leading researchers attempt to identify patterns of change among seabirds...... and marine mammals, and the mechanisms through which climate change drives these changes....

  16. Neutrino Masses from Neutral Top Partners

    CERN Document Server

    Batell, Brian

    2015-01-01

    We present theories of `Natural Neutrinos' in which neutral fermionic top partner fields are simultaneously the right-handed neutrinos (RHN), linking seemingly disparate aspects of the Standard Model structure: a) The RHN top partners are responsible for the observed small neutrino masses, b) They help ameliorate the tuning in the weak scale and address the little hierarchy problem, and c) The factor of $3$ arising from $N_c$ in the top-loop Higgs mass corrections is countered by a factor $3$ from the number of vector-like generations of RHN. The RHN top partners may arise in pseudo-Nambu-Goldstone-Boson (pNGB) Higgs models such as the Twin Higgs, as well as more general Composite, Little, and Orbifold Higgs scenarios, and three simple example models are presented. This framework firmly predicts a TeV-scale seesaw, as the RHN masses are bounded to be below the TeV scale by naturalness. The generation of light neutrino masses relies on a collective breaking of lepton number, allowing for comparatively large ne...

  17. Top Down proteomics: Facts and perspectives

    International Nuclear Information System (INIS)

    Catherman, Adam D.; Skinner, Owen S.; Kelleher, Neil L.

    2014-01-01

    Highlights: • Top Down versus Bottom Up proteomics analysis. • Separations methods for Top Down proteomics. • Developments in mass spectrometry instrumentation and fragmentation. • Native mass spectrometry. - Abstract: The rise of the “Top Down” method in the field of mass spectrometry-based proteomics has ushered in a new age of promise and challenge for the characterization and identification of proteins. Injecting intact proteins into the mass spectrometer allows for better characterization of post-translational modifications and avoids several of the serious “inference” problems associated with peptide-based proteomics. However, successful implementation of a Top Down approach to endogenous or other biologically relevant samples often requires the use of one or more forms of separation prior to mass spectrometric analysis, which have only begun to mature for whole protein MS. Recent advances in instrumentation have been used in conjunction with new ion fragmentation using photons and electrons that allow for better (and often complete) protein characterization on cases simply not tractable even just a few years ago. Finally, the use of native electrospray mass spectrometry has shown great promise for the identification and characterization of whole protein complexes in the 100 kDa to 1 MDa regime, with prospects for complete compositional analysis for endogenous protein assemblies a viable goal over the coming few years

  18. CSR Position in the Top Management Team

    DEFF Research Database (Denmark)

    Strand, Robert

    Recently, a number of positions with corporate social responsibility (CSR) in the position title have been introduced to the top management teams (TMTs) of some of the world’s largest corporations. I explore this phenomenon. I revisit 10 such positions identified in a previous study to add...

  19. Top Four Trends in Student Information Systems

    Science.gov (United States)

    Weathers, Robert

    2013-01-01

    The modern student information systems (SIS) is a powerful administrative tool with robust functionality. As such, it is essential that school and district administrators consider the top trends in modern student information systems before going forward with system upgrades or new purchases. These trends, described herein, are: (1) Support for…

  20. Top Yukawa deviation in extra dimension

    International Nuclear Information System (INIS)

    Haba, Naoyuki; Oda, Kin-ya; Takahashi, Ryo

    2009-01-01

    We suggest a simple one-Higgs-doublet model living in the bulk of five-dimensional spacetime compactified on S 1 /Z 2 , in which the top Yukawa coupling can be smaller than the naive standard-model expectation, i.e. the top quark mass divided by the Higgs vacuum expectation value. If we find only single Higgs particle at the LHC and also observe the top Yukawa deviation, our scenario becomes a realistic candidate beyond the standard model. The Yukawa deviation comes from the fact that the wave function profile of the free physical Higgs field can become different from that of the vacuum expectation value, due to the presence of the brane-localized Higgs potentials. In the Brane-Localized Fermion scenario, we find sizable top Yukawa deviation, which could be checked at the LHC experiment, with a dominant Higgs production channel being the WW fusion. We also study the Bulk Fermion scenario with brane-localized Higgs potential, which resembles the Universal Extra Dimension model with a stable dark matter candidate. We show that both scenarios are consistent with the current electroweak precision measurements.

  1. Käibe kasvu TOP 100

    Index Scriptorium Estoniae

    2003-01-01

    Käibe kasvu TOP 100. 2002. a. netokäibe kasvust Eesti Ehitus OÜ, Russian Estonian Railway Services OÜ, Baltic Pulp & Paper AS-i ja Water Ser AS-i näitel. Diagrammid. Kommenteerivad Selene Rebane ja Rivo Sarapik

  2. Kinematics of electroweak single top quark production

    International Nuclear Information System (INIS)

    Lueck, Jan; Karlsruhe U., EKP

    2006-01-01

    In this thesis, the t-channel matching procedure of two single-top signal Monte Carlo samples is optimized. The s- and matched t-channel samples, generated by MadEvent, are validated by comparing to ZTOP next-to-leading-order calculations. We find good agreement for all kinematic distributions we investigate, except for softer light quark jets due to gluon radiation. Since this has only minor impact on the s-channel, the corresponding MadEvent sample performs its task as expected. For the t-channel, we can conclude that the applied matching procedure leads to a MadEvent sample that successfully describes the kinematic distributions and rates of the 2nd-b quark. However, small differences remain. The discrepancy in the p T -ordered 2nd-leading light jets is mainly due to the absence of initial state gluon splitting and initial and final state gluon radiation matrix elements in the MadEvent sample production. The subsequent PYTHIA showering of the partons is apparently inappropriate for modeling those contributions and not intended for this purpose. The proper way would be to produce all relevant NLO matrix elements and match them as proposed in reference [15]. At present, an NLO-MC-generator for single-top is in preparation [41]. Probably it will be available for future iterations of single-top analyses and will redundantize further matching procedures. We estimate the systematic uncertainty on the single-top acceptance due to the Monte Carlo modeling and find an uncertainty of about 1% on the t-channel acceptance. We obtain a negligible uncertainty well below 1% on the s-channel acceptance. These acceptance uncertainties are very well acceptable for the single-top analyses that are currently under way. A sensitivity study of the simultaneous cross section measurement of the s- and t-channel single-top production modes is conducted. For this purpose, only statistical uncertainties are included. For a future integrated luminosity of 1 fb -1 , we expect to obtain an s

  3. Top-selling childbirth advice books: a discourse analysis.

    Science.gov (United States)

    Kennedy, Holly Powell; Nardini, Katrina; McLeod-Waldo, Rebecca; Ennis, Linda

    2009-12-01

    Recent evidence suggests that one-third of women receive information about pregnancy and childbirth through books. Messages about what characteristics are normal (or expected) in childbirth are disseminated in a variety of ways, including popular childbirth education books, but little study of them has been conducted. The purpose of this investigation is to address that gap by examining the discussions about childbirth in the 10 top-selling books in the United States. Discourse analysis (relating to the public, personal, and political discussions about a specific phenomenon) was used to study 10 best-selling United States childbirth advice books marketed to childbearing women during the first week of November 2007. Book styles ranged from clinical descriptions of pregnancy and birth primarily offering reassurance, self-help information, and danger signs to more folksy and humorous commentaries. Presentation of scientific evidence to support recommendations was uneven and at times inaccurate. Five focal areas of discourse included body image, labor and birth, pain, power and control, and life preparation for motherhood. Top-selling books shine an interesting light on the current state of United States maternity practices. Women and health professionals should assess them carefully and engage with each other about their recommendations and implications for childbirth.

  4. Top-tagging at the energy frontier

    Science.gov (United States)

    Han, Zhenyu; Son, Minho; Tweedie, Brock

    2018-02-01

    At proposed future hadron colliders and in the coming years at the LHC, top quarks will be produced at genuinely multi-TeV energies. Top-tagging at such high energies forces us to confront several new issues in terms of detector capabilities and jet physics. Here, we explore these issues in the context of some simple JHU/CMS-type declustering algorithms and the N -subjettiness jet-shape variable τ32. We first highlight the complementarity between the two tagging approaches at particle level with respect to discriminating top-jets against gluons and quarks, using multivariate optimization scans. We then introduce a basic fast detector simulation, including electromagnetic calorimeter showering patterns determined from GEANT. We consider a number of tricks for processing the fast detector output back to an approximate particle-level picture. Re-optimizing the tagger parameters, we demonstrate that the inevitable losses in discrimination power at very high energies can typically be ameliorated. For example, percent-scale mistag rates might be maintained even in extreme cases where an entire top decay would sit inside of one hadronic calorimeter cell and tracking information is completely absent. We then study three novel physics effects that will come up in the multi-TeV energy regime: gluon radiation off of boosted top quarks, mistags originating from g →t t ¯ , and mistags originating from q →(W /Z )q collinear electroweak splittings with subsequent hadronic decays. The first effect, while nominally a nuisance, can actually be harnessed to slightly improve discrimination against gluons. The second effect can lead to effective O (1 ) enhancements of gluon mistag rates for tight working points. And the third effect, while conceptually interesting, we show to be of highly subleading importance at all energies.

  5. Top-quark mass and top-quark pole mass measurements with the ATLAS detector

    CERN Document Server

    Barillari, Teresa; The ATLAS collaboration

    2017-01-01

    Results of top-quark mass measurements in the di-lepton and in the all-jets top-antitop decay channels with the ATLAS detector are presented. The measurements are obtained using proton--proton collisions at a centre-of-mass energy \\sqrt{s} = 8 TeV at the CERN Large Hadron Collider. The data set used corresponds to an integrated luminosity of 20.2 fb-1. The top-quark mass in the di-lepton channel is measured to be 172.99 +/-0.41 (stat.) +/- 0.74 (syst.) GeV. In the all-jets analysis the top-quark mass is measured to be 173.72 +/- 0.55 (stat.)+/- 1.01 (syst.) GeV. In addition, the top-quark pole mass is determined from inclusive cross-section measurements in the top-antitop di-lepton decay channel with the ATLAS detector. The measurements are obtained using data at \\sqrt{s} = 7 TeV and \\sqrt{s} =8 TeV corresponding to an integrated luminosity of 4.6 fb-1 and 20.2 fb-1 respectively. The top-quark pole mass is measured to be 172.9^{+2.5}_{-2.6} GeV.

  6. ATLAS + CMS top production and properties: Run 1 legacy

    CERN Document Server

    AUTHOR|(SzGeCERN)641905; The ATLAS collaboration

    2015-01-01

    The large Run 1 data sample of top-quark events collected at the Large Hadron Collider allows a variety of measurements to analyse the production and properties of the top quark. Measurements of top-quark production cross sections and top-quark properties in proton-proton collisions with the ATLAS and CMS detectors at the LHC are presented.

  7. Internal combustion engine

    Science.gov (United States)

    Baker, Quentin A.; Mecredy, Henry E.; O'Neal, Glenn B.

    1991-01-01

    An improved engine is provided that more efficiently consumes difficult fuels such as coal slurries or powdered coal. The engine includes a precombustion chamber having a portion thereof formed by an ignition plug. The precombustion chamber is arranged so that when the piston is proximate the head, the precombustion chamber is sealed from the main cylinder or the main combustion chamber and when the piston is remote from the head, the precombustion chamber and main combustion chamber are in communication. The time for burning of fuel in the precombustion chamber can be regulated by the distance required to move the piston from the top dead center position to the position wherein the precombustion chamber and main combustion chamber are in communication.

  8. The Top 10 oomycete pathogens in molecular plant pathology.

    Science.gov (United States)

    Kamoun, Sophien; Furzer, Oliver; Jones, Jonathan D G; Judelson, Howard S; Ali, Gul Shad; Dalio, Ronaldo J D; Roy, Sanjoy Guha; Schena, Leonardo; Zambounis, Antonios; Panabières, Franck; Cahill, David; Ruocco, Michelina; Figueiredo, Andreia; Chen, Xiao-Ren; Hulvey, Jon; Stam, Remco; Lamour, Kurt; Gijzen, Mark; Tyler, Brett M; Grünwald, Niklaus J; Mukhtar, M Shahid; Tomé, Daniel F A; Tör, Mahmut; Van Den Ackerveken, Guido; McDowell, John; Daayf, Fouad; Fry, William E; Lindqvist-Kreuze, Hannele; Meijer, Harold J G; Petre, Benjamin; Ristaino, Jean; Yoshida, Kentaro; Birch, Paul R J; Govers, Francine

    2015-05-01

    Oomycetes form a deep lineage of eukaryotic organisms that includes a large number of plant pathogens which threaten natural and managed ecosystems. We undertook a survey to query the community for their ranking of plant-pathogenic oomycete species based on scientific and economic importance. In total, we received 263 votes from 62 scientists in 15 countries for a total of 33 species. The Top 10 species and their ranking are: (1) Phytophthora infestans; (2, tied) Hyaloperonospora arabidopsidis; (2, tied) Phytophthora ramorum; (4) Phytophthora sojae; (5) Phytophthora capsici; (6) Plasmopara viticola; (7) Phytophthora cinnamomi; (8, tied) Phytophthora parasitica; (8, tied) Pythium ultimum; and (10) Albugo candida. This article provides an introduction to these 10 taxa and a snapshot of current research. We hope that the list will serve as a benchmark for future trends in oomycete research. © 2014 BSPP AND JOHN WILEY & SONS LTD.

  9. SOUND FIELD DIFFUSIVITY AT THE TOP SURFACE OF SCHROEDER DIFFUSER BARRIERS

    Directory of Open Access Journals (Sweden)

    M. R. Monazzam

    2006-10-01

    Full Text Available Reactive barriers are one of the most promising and novel environmental noise barriers. In this case using Schroeder diffusers (e.g. quadratic residue diffusers on the top surface of the T-shape barrier was shown to significantly improve the performance of absorbent T-shape barriers. The reasons behind the high performance of diffuser barriers are considered in this investigation. A question about the diffusivity behavior of Schroeder diffusers when they are utilized on the top of barrier was raised. Diffusion coefficients of a diffuser in different conditions at some receiver locations were predicted by using a 2D boundary element method. It was found that the diffusion coefficient of diffuser at the top of barrier is so small that the diffusivity of the structure is almost the same as rigid T-shape barrier. To find the barrier’s cap behavior, the total field above the top surface of profile barriers was also predicted. It was found that the lowest total energy is at the receiver side of the cap very close to the top surface,which could demonstrate the effect of top surface on absorbing the energy as wave transfers from source edge toward the receiver side of the cap. In this case the amount of minimum total energy depends on the frequency and the configuration of the top surface. A comparison between the reductions of total field at the source side of the cap with the improvements of barrier’s performance was also done. It was shown that the amount of decrease in total field compared to that of an absorbent barrier “Ref” is directly associated to the amount of improvement in the insertion loss made by the diffuser barrier compared to the “Ref” barrier in the wide area on the ground at the shadow zone. Finally it was concluded that the diffuser on the top of barrier does not act as a diffuser and a kind of similarity between the contribution of diffuser and absorbent material on the top of T-profile barrier is seen.

  10. The Situation of Top Universities\\\\\\' Websites in the Islamic World Countries: a Webometric Study

    Directory of Open Access Journals (Sweden)

    Marzieh Goltaji

    2011-10-01

    Full Text Available With regards to important role of universities’ websites, this article aimed to study top universities of the Islamic countries using webometrics methods. Research data were extracted from AltaVista search engine and WEBOMETRICS website. In this study, top universities of the Islamic countries were ranked with some indexes such as number of links, web impact factor, world rank, size, visibility, rich files and scholar. Results showed that there was a significant relation between web impact factor with some indicators such as world rank, size, rich files and scholar, but there was not any significant relation between web impact factor and visibility of the website. Strong significant correlation between top universities of the Islamic world countries websites’ world rank and their ranks based on GDP was another result that we can mention in this study.

  11. Wave-Rotor-Enhanced Gas Turbine Engine Demonstrator

    National Research Council Canada - National Science Library

    Welch, Gerard

    1999-01-01

    The U.S. Army Research Laboratory, NASA Glenn Research Center, and Rolls-Royce Allison are working collaboratively to demonstrate the benefits and viability of a wave-rotor-topped gas turbine engine...

  12. Beyond Standard Model searches with top quarks at ATLAS

    International Nuclear Information System (INIS)

    Chevalier, F.

    2008-01-01

    At the Lhc, the top quark is expected to provide a huge and clean signal. With about eight millions of expected top pairs and three millions of single top events produced per year in the low luminosity runs, and with a low level of backgrounds, the Lhc will open a new opportunity for precision measurements of the top quark properties and for exotic topology searches involving top quarks. As the ATLAS discovery potential on new physics with top quarks is being assessed with many analyses, this paper focuses on two particular topics: heavy neutral resonance and charged Higgs boson searches with top quarks. The analyses and the ATLAS expectations are described.

  13. Measurement of top quark polarisation in t-channel single top quark production

    OpenAIRE

    CMS Collaboration

    2015-01-01

    Journal of High Energy Physics 2016.4 (2016): 073 reproduced by permission of Scuola Internazionale Superiore di Studi Avanzati (SISSA) Artículo escrito por un elevado número de autores, sólo se referencian el que aparece en primer lugar, el nombre del grupo de colaboración, si le hubiera, y los autores pertenecientes a la UAM A first measurement of the top quark spin asymmetry, sensitive to the top quark polarisation, in t-channel single top quark production is presented. It is based o...

  14. Studies on top-quark Monte Carlo modelling for Top2016

    CERN Document Server

    The ATLAS collaboration

    2016-01-01

    This note summarises recent studies on Monte Carlo simulation setups of top-quark pair production used by the ATLAS experiment and presents a new method to deal with interference effects for the $Wt$ single-top-quark production which is compared against previous techniques. The main focus for the top-quark pair production is on the improvement of the modelling of the Powheg generator interfaced to the Pythia8 and Herwig7 shower generators. The studies are done using unfolded data at centre-of-mass energies of 7, 8, and 13 TeV.

  15. Top asymmetry and the search for a light hadronic resonance in association with single top

    CERN Document Server

    Jung, Sunghoon; Wells, James D

    2011-01-01

    The exchange of a light $t$-channel flavor-changing gauge boson, $\\Vp$, with mass $\\sim m_{top}$ remains a leading explanation for the anomalous forward backward asymmetry in top quark production at the Tevatron. Unlike other ideas, including heavier $t$-channel mediators, the light $\\Vp$ model is not easily seen in the $\\mtt$ distribution. We advocate a more promising strategy. While current analyses at hadron colliders may not be sensitive, we propose searching for a $jj$ resonance in association with single top that may allow discovery in existing data. Deviations in the lepton charge asymmetry in this sample should also be present.

  16. Top quark pair production at the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Baernreuther, Peter

    2012-06-28

    One of the most interesting and manifold processes in the Standard Model of elementary particle physics is the top quark pair production. It enabled the discovery of the top quark at the Tevatron in 1995 and the determination of many of its properties. By means of a precise measurement and calculation of the cross section of top quark pair production it is possible to extract the top quark mass. Improvements in the gluon parton distribution functions (important for the Higgs boson production) or improvements in the prediction of the Higgs mass are also closely linked with the top quark pair production. Furthermore, the production process plays an important role in the discovery of new physics. On the one hand the top quark pair decays form the largest part of the background in many BSM models, on the other hand BSM physics can be detected directly in the decay process by investigating the charge symmetry or the invariant mass spectrum. At the LHC it will be possible for the first time to produce a large amount of top quarks; thereby the statistical errors of the observables will be strongly reduced. The enormous increase in the production rate has two reasons. On the one hand, the acceleration energy of the LHC (14 TeV and 7 TeV) is significantly greater than that of the Tevatron (1.96 Tev). This leads to an increase of the cross section by a factor of 100 ({proportional_to}7.3 pb at the Tevatron to {proportional_to}800 pb at 14 TeV LHC). On the other hand, the luminosity of the LHC outperforms the Tevatron by a factor of 10-100. The reduced experimental errors for the observables demand an improvement of the theoretical error. The experimental accuracy of the LHC and the great relevance of the process led to an intensive activity of different research groups in order to improve the calculation of the cross section of top quark pair production. This work presents for the first time a complete numerical result for the full NNLO correction for the top quark pair

  17. Top quark pair production at the LHC

    International Nuclear Information System (INIS)

    Baernreuther, Peter

    2012-01-01

    One of the most interesting and manifold processes in the Standard Model of elementary particle physics is the top quark pair production. It enabled the discovery of the top quark at the Tevatron in 1995 and the determination of many of its properties. By means of a precise measurement and calculation of the cross section of top quark pair production it is possible to extract the top quark mass. Improvements in the gluon parton distribution functions (important for the Higgs boson production) or improvements in the prediction of the Higgs mass are also closely linked with the top quark pair production. Furthermore, the production process plays an important role in the discovery of new physics. On the one hand the top quark pair decays form the largest part of the background in many BSM models, on the other hand BSM physics can be detected directly in the decay process by investigating the charge symmetry or the invariant mass spectrum. At the LHC it will be possible for the first time to produce a large amount of top quarks; thereby the statistical errors of the observables will be strongly reduced. The enormous increase in the production rate has two reasons. On the one hand, the acceleration energy of the LHC (14 TeV and 7 TeV) is significantly greater than that of the Tevatron (1.96 Tev). This leads to an increase of the cross section by a factor of 100 (∝7.3 pb at the Tevatron to ∝800 pb at 14 TeV LHC). On the other hand, the luminosity of the LHC outperforms the Tevatron by a factor of 10-100. The reduced experimental errors for the observables demand an improvement of the theoretical error. The experimental accuracy of the LHC and the great relevance of the process led to an intensive activity of different research groups in order to improve the calculation of the cross section of top quark pair production. This work presents for the first time a complete numerical result for the full NNLO correction for the top quark pair production in quark anti

  18. Reduction of standby energy use in set-top boxes in the United States and the European Union

    Energy Technology Data Exchange (ETDEWEB)

    Zandelin, S.

    2000-06-01

    In the US, there were over 110 million set-top boxes in 1999. About half of these boxes were game consoles. In the EU, the number of set-top boxes was estimated to be about 71 millions in 1999. The most common set-top boxes in the EU were analog satellite receivers. That is quite a difference from the US, where almost no analog satellite receivers exist. It is expected that the amount of set-top boxes will increase rapidly when the broadcasts switch to digital. Set-top boxes in the US consume 7.9 TWh of electricity every year. Of this 5.5 TWh, or 70 %, are consumed while in standby mode. The amount of energy used in standby in the US would be enough to heat about 220,000 Swedish houses. Even though almost half of the set-top boxes in the US are game consoles, they only use 30 % of the set-top energy. This is because they have low standby power. Since most analog cable boxes have a very high standby power, 46 % of the set-top energy come from analog cable boxes. Analog cable boxes use 76 % of the energy in standby mode. The set-top electricity consumption in the US is 0.70 % of the residential electricity use. In the EU the total amount of energy used by set-top boxes is 5.1 TWh every year. The fraction used in standby mode in the EU, 60 %, is smaller than in the US. In the EU, the most common boxes are the analog satellite receivers. They use 59 % of the total set-top energy, or 3.0 TWh. The set-top energy share of the residential electricity use in the EU is about 0.85 %. Sweden has a share that is less than half of the EU share. One reason for that could be that a lot of electricity is used for heating in Sweden. In most set-top boxes, high standby power is because most circuitry and components are still powered when they are not in use. By making modest redesigns and changes of communications protocols between the service provider and the user, the energy efficiency could be increased and the standby power consumption reduced significantly. If nothing is done to

  19. Teamwork for Oversight of Processes and Systems (TOPS). Implementation guide for TOPS version 2.0, 10 August 1992

    Science.gov (United States)

    Strand, Albert A.; Jackson, Darryl J.

    1992-01-01

    As the nation redefines priorities to deal with a rapidly changing world order, both government and industry require new approaches for oversight of management systems, particularly for high technology products. Declining defense budgets will lead to significant reductions in government contract management personnel. Concurrently, defense contractors are reducing administrative and overhead staffing to control costs. These combined pressures require bold approaches for the oversight of management systems. In the Spring of 1991, the DPRO and TRW created a Process Action Team (PAT) to jointly prepare a Performance Based Management (PBM) system titled Teamwork for Oversight of Processes and Systems (TOPS). The primary goal is implementation of a performance based management system based on objective data to review critical TRW processes with an emphasis on continuous improvement. The processes are: Finance and Business Systems, Engineering and Manufacturing Systems, Quality Assurance, and Software Systems. The team established a number of goals: delivery of quality products to contractual terms and conditions; ensure that TRW management systems meet government guidance and good business practices; use of objective data to measure critical processes; elimination of wasteful/duplicative reviews and audits; emphasis on teamwork--all efforts must be perceived to add value by both sides and decisions are made by consensus; and synergy and the creation of a strong working trust between TRW and the DPRO. TOPS permits the adjustment of oversight resources when conditions change or when TRW systems performance indicate either an increase or decrease in surveillance is appropriate. Monthly Contractor Performance Assessments (CPA) are derived from a summary of supporting system level and process-level ratings obtained from objective process-level data. Tiered, objective, data-driven metrics are highly successful in achieving a cooperative and effective method of measuring

  20. Teamwork for Oversight of Processes and Systems (TOPS). Implementation guide for TOPS version 2.0, 10 August 1992

    Science.gov (United States)

    Strand, Albert A.; Jackson, Darryl J.

    As the nation redefines priorities to deal with a rapidly changing world order, both government and industry require new approaches for oversight of management systems, particularly for high technology products. Declining defense budgets will lead to significant reductions in government contract management personnel. Concurrently, defense contractors are reducing administrative and overhead staffing to control costs. These combined pressures require bold approaches for the oversight of management systems. In the Spring of 1991, the DPRO and TRW created a Process Action Team (PAT) to jointly prepare a Performance Based Management (PBM) system titled Teamwork for Oversight of Processes and Systems (TOPS). The primary goal is implementation of a performance based management system based on objective data to review critical TRW processes with an emphasis on continuous improvement. The processes are: Finance and Business Systems, Engineering and Manufacturing Systems, Quality Assurance, and Software Systems. The team established a number of goals: delivery of quality products to contractual terms and conditions; ensure that TRW management systems meet government guidance and good business practices; use of objective data to measure critical processes; elimination of wasteful/duplicative reviews and audits; emphasis on teamwork--all efforts must be perceived to add value by both sides and decisions are made by consensus; and synergy and the creation of a strong working trust between TRW and the DPRO. TOPS permits the adjustment of oversight resources when conditions change or when TRW systems performance indicate either an increase or decrease in surveillance is appropriate. Monthly Contractor Performance Assessments (CPA) are derived from a summary of supporting system level and process-level ratings obtained from objective process-level data. Tiered, objective, data-driven metrics are highly successful in achieving a cooperative and effective method of measuring

  1. Opportunities with top quarks at future circular colliders

    CERN Document Server

    Fuks, Benjamin

    2014-01-01

    We describe various studies relevant for top physics at future circular collider projects currently under discussion. We show how highly-massive top-antitop systems produced in proton-proton collisions at a center-of-mass energy of 100 TeV could be observed and employed for constraining top dipole moments, investigate the reach of future proton-proton and electron-positron machines to top flavor-changing neutral interactions, and discuss top parton densities.

  2. Femtosecond Photon-Counting Receiver

    Science.gov (United States)

    Krainak, Michael A.; Rambo, Timothy M.; Yang, Guangning; Lu, Wei; Numata, Kenji

    2016-01-01

    An optical correlation receiver is described that provides ultra-precise distance and/or time/pulse-width measurements even for weak (single photons) and short (femtosecond) optical signals. A new type of optical correlation receiver uses a fourth-order (intensity) interferometer to provide micron distance measurements even for weak (single photons) and short (femtosecond) optical signals. The optical correlator uses a low-noise-integrating detector that can resolve photon number. The correlation (range as a function of path delay) is calculated from the variance of the photon number of the difference of the optical signals on the two detectors. Our preliminary proof-of principle data (using a short-pulse diode laser transmitter) demonstrates tens of microns precision.

  3. Scintillation-Hardened GPS Receiver

    Science.gov (United States)

    Stephens, Donald R.

    2015-01-01

    CommLargo, Inc., has developed a scintillation-hardened Global Positioning System (GPS) receiver that improves reliability for low-orbit missions and complies with NASA's Space Telecommunications Radio System (STRS) architecture standards. A software-defined radio (SDR) implementation allows a single hardware element to function as either a conventional radio or as a GPS receiver, providing backup and redundancy for platforms such as the International Space Station (ISS) and high-value remote sensing platforms. The innovation's flexible SDR implementation reduces cost, weight, and power requirements. Scintillation hardening improves mission reliability and variability. In Phase I, CommLargo refactored an open-source GPS software package with Kalman filter-based tracking loops to improve performance during scintillation and also demonstrated improved navigation during a geomagnetic storm. In Phase II, the company generated a new field-programmable gate array (FPGA)-based GPS waveform to demonstrate on NASA's Space Communication and Navigation (SCaN) test bed.

  4. Hyper-X Vehicle Model - Top Front View

    Science.gov (United States)

    1996-01-01

    A top front view of an early desk-top model of NASA's X-43A 'Hyper-X,' or Hypersonic Experimental Vehicle, developed to flight test a dual-mode ramjet/scramjet propulsion system at speeds from Mach 7 up to Mach 10 (7 to 10 times the speed of sound, which varies with temperature and altitude). Hyper-X, the flight vehicle for which is designated as X-43A, is an experimental flight-research program seeking to demonstrate airframe-integrated, 'air-breathing' engine technologies that promise to increase payload capacity for future vehicles, including hypersonic aircraft (faster than Mach 5) and reusable space launchers. This multiyear program is currently underway at NASA Dryden Flight Research Center, Edwards, California. The Hyper-X schedule calls for its first flight later this year (2000). Hyper-X is a joint program, with Dryden sharing responsibility with NASA's Langley Research Center, Hampton, Virginia. Dryden's primary role is to fly three unpiloted X-43A research vehicles to validate engine technologies and hypersonic design tools as well as the hypersonic test facility at Langley. Langley manages the program and leads the technology development effort. The Hyper-X Program seeks to significantly expand the speed boundaries of air-breathing propulsion by being the first aircraft to demonstrate an airframe-integrated, scramjet-powered free flight. Scramjets (supersonic-combustion ramjets) are ramjet engines in which the airflow through the whole engine remains supersonic. Scramjet technology is challenging because only limited testing can be performed in ground facilities. Long duration, full-scale testing requires flight research. Scramjet engines are air-breathing, capturing their oxygen from the atmosphere. Current spacecraft, such as the Space Shuttle, are rocket powered, so they must carry both fuel and oxygen for propulsion. Scramjet technology-based vehicles need to carry only fuel. By eliminating the need to carry oxygen, future hypersonic vehicles will

  5. 40 CFR 35.2114 - Value engineering.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Value engineering. 35.2114 Section 35... STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2114 Value engineering. (a) If the project has not received Step 2 grant assistance the applicant shall conduct value engineering...

  6. First woman named to endowed engineering professorship

    OpenAIRE

    Nystrom, Lynn A.

    2005-01-01

    Karen A. Thole, Virginia Tech professor of mechanical engineering, is the first female recipient of an endowed engineering professorship at the university. Thole has received the William S. Cross Professorship in the College of Engineering, established in 1984 by a generous gift from William S. Cross Jr., of Greensboro, N.C.

  7. Measurement of the Mass Difference Between Top and Anti-top Quarks at CDF

    CERN Document Server

    Aaltonen, T.; Amerio, S.; Amidei, D.; Anastassov, A.; Annovi, A.; Antos, J.; Apollinari, G.; Appel, J.A.; Arisawa, T.; Artikov, A.; Asaadi, J.; Ashmanskas, W.; Auerbach, B.; Aurisano, A.; Azfar, F.; Badgett, W.; Bae, T.; Barbaro-Galtieri, A.; Barnes, V.E.; Barnett, B.A.; Barria, P.; Bartos, P.; Bauce, M.; Bedeschi, F.; Behari, S.; Bellettini, G.; Bellinger, J.; Benjamin, D.; Beretvas, A.; Bhatti, A.; Bisello, D.; Bizjak, I.; Bland, K.R.; Blumenfeld, B.; Bocci, A.; Bodek, A.; Bortoletto, D.; Boudreau, J.; Boveia, A.; Brigliadori, L.; Bromberg, C.; Brucken, E.; Budagov, J.; Budd, H.S.; Burkett, K.; Busetto, G.; Bussey, P.; Buzatu, A.; Calamba, A.; Calancha, C.; Camarda, S.; Campanelli, M.; Campbell, M.; Canelli, F.; Carls, B.; Carlsmith, D.; Carosi, R.; Carrillo, S.; Carron, S.; Casal, B.; Casarsa, M.; Castro, A.; Catastini, P.; Cauz, D.; Cavaliere, V.; Cavalli-Sforza, M.; Cerri, A.; Cerrito, L.; Chen, Y.C.; Chertok, M.; Chiarelli, G.; Chlachidze, G.; Chlebana, F.; Cho, K.; Chokheli, D.; Chung, W.H.; Chung, Y.S.; Ciocci, M.A.; Clark, A.; Clarke, C.; Compostella, G.; Convery, M.E.; Conway, J.; Corbo, M.; Cordelli, M.; Cox, C.A.; Cox, D.J.; Crescioli, F.; Cuevas, J.; Culbertson, R.; Dagenhart, D.; d'Ascenzo, N.; Datta, M.; de Barbaro, P.; Dell'Orso, M.; Demortier, L.; Deninno, M.; Devoto, F.; d'Errico, M.; Di Canto, A.; Di Ruzza, B.; Dittmann, J.R.; D'Onofrio, M.; Donati, S.; Dong, P.; Dorigo, M.; Dorigo, T.; Ebina, K.; Elagin, A.; Eppig, A.; Erbacher, R.; Errede, S.; Ershaidat, N.; Eusebi, R.; Farrington, S.; Feindt, M.; Fernandez, J.P.; Field, R.; Flanagan, G.; Forrest, R.; Frank, M.J.; Franklin, M.; Freeman, J.C.; Funakoshi, Y.; Furic, I.; Gallinaro, M.; Garcia, J.E.; Garfinkel, A.F.; Garosi, P.; Gerberich, H.; Gerchtein, E.; Giagu, S.; Giakoumopoulou, V.; Giannetti, P.; Gibson, K.; Ginsburg, C.M.; Giokaris, N.; Giromini, P.; Giurgiu, G.; Glagolev, V.; Glenzinski, D.; Gold, M.; Goldin, D.; Goldschmidt, N.; Golossanov, A.; Gomez, G.; Gomez-Ceballos, G.; Goncharov, M.; Gonzalez, O.; Gorelov, I.; Goshaw, A.T.; Goulianos, K.; Grinstein, S.; Grosso-Pilcher, C.; Group, R.C.; Guimaraes da Costa, J.; Hahn, S.R.; Halkiadakis, E.; Hamaguchi, A.; Han, J.Y.; Happacher, F.; Hara, K.; Hare, D.; Hare, M.; Harr, R.F.; Hatakeyama, K.; Hays, C.; Heck, M.; Heinrich, J.; Herndon, M.; Hewamanage, S.; Hocker, A.; Hopkins, W.; Horn, D.; Hou, S.; Hughes, R.E.; Hurwitz, M.; Husemann, U.; Hussain, N.; Hussein, M.; Huston, J.; Introzzi, G.; Iori, M.; Ivanov, A.; James, E.; Jang, D.; Jayatilaka, B.; Jeon, E.J.; Jindariani, S.; Jones, M.; Joo, K.K.; Jun, S.Y.; Junk, T.R.; Kamon, T.; Karchin, P.E.; Kasmi, A.; Kato, Y.; Ketchum, W.; Keung, J.; Khotilovich, V.; Kilminster, B.; Kim, D.H.; Kim, H.S.; Kim, J.E.; Kim, M.J.; Kim, S.B.; Kim, S.H.; Kim, Y.K.; Kim, Y.J.; Kimura, N.; Kirby, M.; Klimenko, S.; Knoepfel, K.; Kondo, K.; Kong, D.J.; Konigsberg, J.; Kotwal, A.V.; Kreps, M.; Kroll, J.; Krop, D.; Kruse, M.; Krutelyov, V.; Kuhr, T.; Kurata, M.; Kwang, S.; Laasanen, A.T.; Lami, S.; Lammel, S.; Lancaster, M.; Lander, R.L.; Lannon, K.; Lath, A.; Latino, G.; LeCompte, T.; Lee, E.; Lee, H.S.; Lee, J.S.; Lee, S.W.; Leo, S.; Leone, S.; Lewis, J.D.; Limosani, A.; Lin, C.J.; Lindgren, M.; Lipeles, E.; Lister, A.; Litvintsev, D.O.; Liu, C.; Liu, H.; Liu, Q.; Liu, T.; Lockwitz, S.; Loginov, A.; Lucchesi, D.; Lueck, J.; Lujan, P.; Lukens, P.; Lungu, G.; Lys, J.; Lysak, R.; Madrak, R.; Maeshima, K.; Maestro, P.; Malik, S.; Manca, G.; Manousakis-Katsikakis, A.; Margaroli, F.; Marino, C.; Martinez, M.; Mastrandrea, P.; Matera, K.; Mattson, M.E.; Mazzacane, A.; Mazzanti, P.; McFarland, K.S.; McIntyre, P.; McNulty, R.; Mehta, A.; Mehtala, P.; Mesropian, C.; Miao, T.; Mietlicki, D.; Mitra, A.; Miyake, H.; Moed, S.; Moggi, N.; Mondragon, M.N.; Moon, C.S.; Moore, R.; Morello, M.J.; Morlock, J.; Movilla Fernandez, P.; Mukherjee, A.; Muller, Th.; Murat, P.; Mussini, M.; Nachtman, J.; Nagai, Y.; Naganoma, J.; Nakano, I.; Napier, A.; Nett, J.; Neu, C.; Neubauer, M.S.; Nielsen, J.; Nodulman, L.; Noh, S.Y.; Norniella, O.; Oakes, L.; Oh, S.H.; Oh, Y.D.; Oksuzian, I.; Okusawa, T.; Orava, R.; Ortolan, L.; Pagan Griso, S.; Pagliarone, C.; Palencia, E.; Papadimitriou, V.; Paramonov, A.A.; Patrick, J.; Pauletta, G.; Paulini, M.; Paus, C.; Pellett, D.E.; Penzo, A.; Phillips, T.J.; Piacentino, G.; Pianori, E.; Pilot, J.; Pitts, K.; Plager, C.; Pondrom, L.; Poprocki, S.; Potamianos, K.; Prokoshin, F.; Pranko, A.; Ptohos, F.; Punzi, G.; Rahaman, A.; Ramakrishnan, V.; Ranjan, N.; Redondo, I.; Renton, P.; Rescigno, M.; Riddick, T.; Rimondi, F.; Ristori, L.; Robson, A.; Rodrigo, T.; Rodriguez, T.; Rogers, E.; Rolli, S.; Roser, R.; Ruffini, F.; Ruiz, A.; Russ, J.; Rusu, V.; Safonov, A.; Sakumoto, W.K.; Sakurai, Y.; Santi, L.; Sato, K.; Saveliev, V.; Savoy-Navarro, A.; Schlabach, P.; Schmidt, A.; Schmidt, E.E.; Schwarz, T.; Scodellaro, L.; Scribano, A.; Scuri, F.; Seidel, S.; Seiya, Y.; Semenov, A.; Sforza, F.; Shalhout, S.Z.; Shears, T.; Shepard, P.F.; Shimojima, M.; Shochet, M.; Shreyber-Tecker, I.; Simonenko, A.; Sinervo, P.; Sliwa, K.; Smith, J.R.; Snider, F.D.; Soha, A.; Sorin, V.; Song, H.; Squillacioti, P.; Stancari, M.; St. Denis, R.; Stelzer, B.; Stelzer-Chilton, O.; Stentz, D.; Strologas, J.; Strycker, G.L.; Sudo, Y.; Sukhanov, A.; Suslov, I.; Takemasa, K.; Takeuchi, Y.; Tang, J.; Tecchio, M.; Teng, P.K.; Thom, J.; Thome, J.; Thompson, G.A.; Thomson, E.; Toback, D.; Tokar, S.; Tollefson, K.; Tomura, T.; Tonelli, D.; Torre, S.; Torretta, D.; Totaro, P.; Trovato, M.; Ukegawa, F.; Uozumi, S.; Varganov, A.; Vazquez, F.; Velev, G.; Vellidis, C.; Vidal, M.; Vila, I.; Vilar, R.; Vizan, J.; Vogel, M.; Volpi, G.; Wagner, P.; Wagner, R.L.; Wakisaka, T.; Wallny, R.; Wang, S.M.; Warburton, A.; Waters, D.; Wester, W.C., III; Whiteson, D.; Wicklund, A.B.; Wicklund, E.; Wilbur, S.; Wick, F.; Williams, H.H.; Wilson, J.S.; Wilson, P.; Winer, B.L.; Wittich, P.; Wolbers, S.; Wolfe, H.; Wright, T.; Wu, X.; Wu, Z.; Yamamoto, K.; Yamato, D.; Yang, T.; Yang, U.K.; Yang, Y.C.; Yao, W.M.; Yeh, G.P.; Yi, K.; Yoh, J.; Yorita, K.; Yoshida, T.; Yu, G.B.; Yu, I.; Yu, S.S.; Yun, J.C.; Zanetti, A.; Zeng, Y.; Zhou, C.; Zucchelli, S.

    2013-03-18

    We present a measurement of the mass difference between top ($t$) and anti-top ($\\bar{t}$) quarks using $t\\bar{t}$ candidate events reconstructed in the final state with one lepton and multiple jets. We use the full data set of Tevatron $\\sqrt{s} = 1.96$ TeV proton-antiproton collisions recorded by the CDF II detector, corresponding to an integrated luminosity of 8.7 fb$^{-1}$. We estimate event-by-event the mass difference to construct templates for top-quark signal events and background events. The resulting mass difference distribution of data compared to signal and background templates using a likelihood fit yields $\\Delta M_{top} = {M}_{t} - {M}_{\\bar{t}} = -1.95 $pm$ 1.11 (stat) $pm$ 0.59 (syst)$ and is in agreement with the standard model prediction of no mass difference.

  8. PREFACE: 5th International Workshop on Top Quark Physics (TOP2012)

    Science.gov (United States)

    Salamanna, G.; Boisvert, V.; Cerrito, L.; Khan, A.; Moretti, S.; Owen, M.; Schwanenberger, C.

    2013-07-01

    The 5th International Workshop on Top Quark Physics (TOP 2012) took place in Winchester, UK, from the 16-21 September. It gathered students as well as people active in the top quark sector and provided a framework to highlight the newest results and matters related to top quark physics. Discovered in 1995, the top quark is the sixth and heaviest of all quarks, and it is the only one with a lifetime short enough to be observed 'naked'. This makes it an important testing ground in the search for new physics. In fact, the fact of its mass being so much larger than the other quarks, hints at its special role in the Higgs mechanism. For the same reason, in many models of New Physics, new heavy resonances are expected to couple mostly with top quarks. Even if no new particles are observed, the direct correlation between its angular momentum and that of its detectable decay products allows us to probe indirectly New Physics in action when top quarks are created. In this edition of the TOP conference series, for the first time, the agenda was equally balanced between 'traditional' measurements and the now vast number of searches for physics BSM in the top quark sector, thanks mostly to the amount of data collected at the LHC in its Run I. New results were presented by both the Tevatron and the LHC collaborations: improved ttbar and single top cross-section measurements, refined techniques to measure the top quark mass and a large number of results on properties such as spin correlation and W boson polarization in top quark decays were shown. More technical discussions on the experimental issues, both from the detector and the simulation side also took place, drawing together experimentalists and theorists. Reviews of the latest results on ttbar asymmetry both from CDF and D0 and from ATLAS and CMS were shown, and theorists active in the field made some interesting points on this hot topic. Additionally, results on the search for fourth generation fermions and new

  9. Engineering Cartilage

    Science.gov (United States)

    ... Research Matters NIH Research Matters March 3, 2014 Engineering Cartilage Artistic rendering of human stem cells on ... situations has been a major goal in tissue engineering. Cartilage contains water, collagen, proteoglycans, and chondrocytes. Collagens ...

  10. Governing Engineering

    DEFF Research Database (Denmark)

    Buch, Anders

    2012-01-01

    Most people agree that our world face daunting problems and, correctly or not, technological solutions are seen as an integral part of an overall solution. But what exactly are the problems and how does the engineering ‘mind set’ frame these problems? This chapter sets out to unravel dominant...... perspectives in challenge per-ception in engineering in the US and Denmark. Challenge perception and response strategies are closely linked through discursive practices. Challenge perceptions within the engineering community and the surrounding society are thus critical for the shaping of engineering education...... and the engineering profession. Through an analysis of influential reports and position papers on engineering and engineering education the chapter sets out to identify how engineering is problematized and eventually governed. Drawing on insights from governmentality studies the chapter strives to elicit the bodies...

  11. Industrial Engineering

    DEFF Research Database (Denmark)

    Karlsson, Christer

    2015-01-01

    Industrial engineering is a discipline that is concerned with increasing the effectiveness of (primarily) manufacturing and (occasionally).......Industrial engineering is a discipline that is concerned with increasing the effectiveness of (primarily) manufacturing and (occasionally)....

  12. Governing Engineering

    DEFF Research Database (Denmark)

    Buch, Anders

    2011-01-01

    Abstract: Most people agree that our world faces daunting problems and, correctly or not, technological solutions are seen as an integral part of an overall solution. But what exactly are the problems and how does the engineering ‘mind set’ frame these problems? This chapter sets out to unravel...... dominant perspectives in challenge perception in engineering in the US and Denmark. Challenge perception and response strategies are closely linked through discursive practices. Challenge perceptions within the engineering community and the surrounding society are thus critical for the shaping...... of engineering education and the engineering profession. Through an analysis of influential reports and position papers on engineering and engineering education the chapter sets out to identify how engineering is problematized and eventually governed. Drawing on insights from governmentality studies the chapter...

  13. Computer Engineers.

    Science.gov (United States)

    Moncarz, Roger

    2000-01-01

    Looks at computer engineers and describes their job, employment outlook, earnings, and training and qualifications. Provides a list of resources related to computer engineering careers and the computer industry. (JOW)

  14. Engineering _ litteraturliste

    DEFF Research Database (Denmark)

    Sillasen, Martin Krabbe; Daugbjerg, Peer; Nielsen, Keld

    2017-01-01

    Litteraturliste udarbejdet som grundlag for artiklen ”Engineering – svaret på naturfagenes udfordringer?”......Litteraturliste udarbejdet som grundlag for artiklen ”Engineering – svaret på naturfagenes udfordringer?”...

  15. Bottom-up photonic crystal approach with top-down defect and heterostructure fine-tuning.

    Science.gov (United States)

    Ding, Tao; Song, Kai; Clays, Koen; Tung, Chen-Ho

    2010-03-16

    We combine the most efficient (chemical) approach toward three-dimensional photonic crystals with the most convenient (physical) technique for creating non-close-packed crystalline structures. Self-assembly of colloidal particles in artificial opals is followed by a carefully tuned plasma etching treatment. By covering the resulting top layer of more open structure with original dense opal, embedded defect layers and heterostructures can be conveniently designed for advanced photonic band gap and band edge engineering.

  16. TOP500 Supercomputers for June 2003

    Energy Technology Data Exchange (ETDEWEB)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2003-06-23

    21st Edition of TOP500 List of World's Fastest Supercomputers Released MANNHEIM, Germany; KNOXVILLE, Tenn.;&BERKELEY, Calif. In what has become a much-anticipated event in the world of high-performance computing, the 21st edition of the TOP500 list of the world's fastest supercomputers was released today (June 23, 2003). The Earth Simulator supercomputer built by NEC and installed last year at the Earth Simulator Center in Yokohama, Japan, with its Linpack benchmark performance of 35.86 Tflop/s (teraflops or trillions of calculations per second), retains the number one position. The number 2 position is held by the re-measured ASCI Q system at Los Alamos National Laboratory. With 13.88 Tflop/s, it is the second system ever to exceed the 10 Tflop/smark. ASCIQ was built by Hewlett-Packard and is based on the AlphaServerSC computer system.

  17. Top quark kinematics and mass determination

    International Nuclear Information System (INIS)

    Williams, H.H.

    1994-10-01

    An analysis is presented of 10 W + ≥ 3 jet events, each with evidence for the presence of a b quark, that were recently observed by the CDF collaboration. Seven of these events include a fourth jet and can be explicitly reconstructed as t bar t production. The best estimate of the top quark mass is M t = 174 ± 10 -12 +13 GeV/c 2 . A study has also been performed to see if the kinematical properties of events with W + ≥ 3 jets gives evidence for top production. An excess of events with large jet energies, compared to that expected from direct production of W + ≥ 3 jets, is observed. A large fraction of these events also contain a b-quark and a fourth jet

  18. The heavy top quark and supersymmetry

    Energy Technology Data Exchange (ETDEWEB)

    Hall, L.J. [Lawrence Berkeley Lab., CA (United States)]|[Univ. of California, Berkeley, CA (United States)

    1997-01-01

    Three aspects of supersymmetric theories are discussed: electroweak symmetry breaking, the issues of flavor, and gauge unification. The heavy top quark plays an important, sometimes dominant, role in each case. Additional symmetries lead to extensions of the Standard Model which can provide an understanding for many of the outstanding problems of particle physics. A broken supersymmetric extension of spacetime allows electroweak symmetry breaking to follow from the dynamics of the heavy top quark; an extension of isospin provides a constrained framework for understanding the pattern of quark and lepton masses; and a grand unified extension of the Standard Model gauge group provides an elegant understanding of the gauge quantum numbers of the components of a generation. Experimental signatures for each of these additional symmetries are discussed.

  19. Three-body Supersymmetric Top Decays

    CERN Document Server

    Belyaev, A; Lola, S; Belyaev, Alexander; Ellis, John; Lola, Smaragda

    2000-01-01

    We discuss three-body supersymmetric top decays, in schemes both with andwithout R-parity conservation, assuming that sfermion masses are larger thanm_t. We find that MSSM top decays into chargino/neutralino pairs have a strongkinematic suppression in the region of the supersymmetric parameter spaceconsistent with the LEP limits, with a decay width =< 10^{-5} GeV. MSSM topdecays into neutralino pairs have less kinematical suppression, but require aflavour-changing vertex, and are likely to have a smaller rate. On the otherhand, R-violating decays to single charginos, neutralinos and conventionalfermions can be larger for values of the R-violating couplings still permittedby other upper limits. The cascade decays of the charginos and neutralinos maylead to spectacular signals with explicit lepton-number violation, such aslike-sign lepton events.

  20. Populating the Landscape: a top down approach

    CERN Document Server

    Hawking, Stephen William; Hertog, Thomas

    2006-01-01

    We put forward a framework for cosmology that combines the string landscape with no boundary initial conditions. In this framework, amplitudes for alternative histories for the universe are calculated with final boundary conditions only. This leads to a top down approach to cosmology, in which the histories of the universe depend on the precise question asked. We study the observational consequences of no boundary initial conditions on the landscape, and outline a scheme to test the theory. This is illustrated in a simple model landscape that admits several alternative inflationary histories for the universe. Only a few of the possible vacua in the landscape will be populated. We also discuss in what respect the top down approach differs from other approaches to cosmology in the string landscape, like eternal inflation.

  1. Probing New Physics with Single Top + X

    International Nuclear Information System (INIS)

    Walker, D.G.E.; Yu, Jiang-Hao; Yuan, C.P.

    2012-01-01

    We investigate single top production in association with a variety of Standard Model final states with a focus on the early LHC run. Here X can be jets, large missing transverse momentum and/or electroweak gauge bosons. For this review, we focus on searches for new W' gauge bosons and heavy B' quarks. A general survey of the possible new physics with associated single top production can be found in literature. In essence, the channel probes a variety of new physics, is intricately tied to the new physics at the TeV scale and is essential for maximizing the potential of the early LHC for new physics. We showed TeV W' bosons and B' heavy quarks are easily accessible during the early LHC running

  2. The heavy top quark and supersymmetry

    International Nuclear Information System (INIS)

    Hall, L.J.; Univ. of California, Berkeley, CA

    1996-01-01

    Three aspects of supersymmetric theories are discussed: electroweak symmetry breaking, the issues of flavor, and gauge unification. The heavy top quark plays an important, sometimes dominant, role in each case. Additional symmetries lead to extensions of the standard model which can provide an understanding for many of the outstanding problems of particle physics. A broken supersymmetric extension of spacetime allows electroweak symmetry breaking to follow from the dynamics of the heavy top quark; an extension of isospin provides a constrained framework for understanding the pattern of quark and lepton masses; and a grand unified extension of the standard model gauge group provides an elegant understanding of the gauge quantum numbers of the components of a generation. Experimental signatures for each of these additional symmetries are discussed

  3. The heavy top quark and supersymmetry

    International Nuclear Information System (INIS)

    Hall, L.J.

    1997-01-01

    Three aspects of supersymmetric theories are discussed: electroweak symmetry breaking, the issues of flavor, and gauge unification. The heavy top quark plays an important, sometimes dominant, role in each case. Additional symmetries lead to extensions of the Standard Model which can provide an understanding for many of the outstanding problems of particle physics. A broken supersymmetric extension of spacetime allows electroweak symmetry breaking to follow from the dynamics of the heavy top quark; an extension of isospin provides a constrained framework for understanding the pattern of quark and lepton masses; and a grand unified extension of the Standard Model gauge group provides an elegant understanding of the gauge quantum numbers of the components of a generation. Experimental signatures for each of these additional symmetries are discussed

  4. Entanglement entropy in top-down models

    Energy Technology Data Exchange (ETDEWEB)

    Jones, Peter A.R.; Taylor, Marika [Mathematical Sciences and STAG Research Centre, University of Southampton,Highfield, Southampton, SO17 1BJ (United Kingdom)

    2016-08-26

    We explore holographic entanglement entropy in ten-dimensional supergravity solutions. It has been proposed that entanglement entropy can be computed in such top-down models using minimal surfaces which asymptotically wrap the compact part of the geometry. We show explicitly in a wide range of examples that the holographic entanglement entropy thus computed agrees with the entanglement entropy computed using the Ryu-Takayanagi formula from the lower-dimensional Einstein metric obtained from reduction over the compact space. Our examples include not only consistent truncations but also cases in which no consistent truncation exists and Kaluza-Klein holography is used to identify the lower-dimensional Einstein metric. We then give a general proof, based on the Lewkowycz-Maldacena approach, of the top-down entanglement entropy formula.

  5. Entanglement entropy in top-down models

    International Nuclear Information System (INIS)

    Jones, Peter A.R.; Taylor, Marika

    2016-01-01

    We explore holographic entanglement entropy in ten-dimensional supergravity solutions. It has been proposed that entanglement entropy can be computed in such top-down models using minimal surfaces which asymptotically wrap the compact part of the geometry. We show explicitly in a wide range of examples that the holographic entanglement entropy thus computed agrees with the entanglement entropy computed using the Ryu-Takayanagi formula from the lower-dimensional Einstein metric obtained from reduction over the compact space. Our examples include not only consistent truncations but also cases in which no consistent truncation exists and Kaluza-Klein holography is used to identify the lower-dimensional Einstein metric. We then give a general proof, based on the Lewkowycz-Maldacena approach, of the top-down entanglement entropy formula.

  6. A Search for new particles decaying into top quark anti-top quark pairs

    Energy Technology Data Exchange (ETDEWEB)

    Cassada, Josh Aaron [Univ. of Rochester, NY (United States)

    2000-01-01

    We use 106 pb-1 of data collected with the Collider Detector at Fermilab to search for narrow-width particles decaying to a top and an anti-top quark. We measure the t$\\bar{t}$ invariant mass distribution by requiring that either t or $\\bar{t}$ decays semileptonically to an electron or muon and the other decays hadronically.

  7. Problem Based Learning for engineering.

    Science.gov (United States)

    Kumar, Dinesh; Radcliffe, Pj

    2017-07-01

    the role of Problem Based Learning (PBL) is relative clear in domains such as medicine but its efficacy in engineering is as yet less certain. To clarify the role of PBL in engineering, a 3 day workshop was conducted for senior Brazilian engineering academics where they were given the theory and then an immersive PBL experience. One major purpose for running this workshop was for them to identify suitable courses where PBL could be considered. During this workshop, they were split in teams and given a diverse range of problems. At the conclusion of the workshop, a quantifiable survey was conducted and the results show that PBL can deliver superior educational outcomes providing the student group is drawn from the top 5% of the year 12 students, and that significantly higher resources are made available. Thus, any proposed PBL program in engineering must be able to demonstrate that it can meet these requirements before it can move forward to implementation.

  8. The top 50 cited articles on chordomas.

    Science.gov (United States)

    Ikpeze, Tochukwu; Mesfin, Addisu

    2018-03-01

    Chordomas are rare malignant primary tumors of the spine. In the mobile spine and sacrum an en-bloc resection is associated with decreased rates of recurrence. Our objective was to identify the top cited articles in chordoma research and to further analyze characteristics of these articles. In March 2017, we used ISI Web of Science (v5.11, Thomas Reuter, Philadelphia, Pennsylvania, USA) to search for the following key word: "chordoma". Articles were searched from 1900 to 2017. Articles were ranked based on number of citations. The results were evaluated to determine articles most clinically relevant to the management of chordomas. The top 50 articles that met the search criteria were further characterized on the basis of: title, author, citation density, journal of publication, year (and decade) of publication, institution and country of origin and paper topic. A total of 1,043 articles matched the search criteria. The most influential 50 articles were cited 65 to 290 times. The articles were published between 1926 and 2012, and all articles were published in English. Thirty-three publications (66%) originated from the United States and seven (14%) from Italy. Cancer accounted for the most frequent (n=9) destination journal followed by Journal of Bone and Joint Surgery (n=4). A total of 41 institutions contributed to the top 50 articles. The most common article types were: clinical 44% (n=22), papers that combined clinical and pathology findings 18% (n=9) and basic science research 14% (n=7). The top 50 cited articles on chordomas are predominantly clinical papers, arising from the United States and most frequently published in Cancer and Journal of Bone and Joint Surgery .

  9. Boosted dibosons from mixed heavy top squarks

    Science.gov (United States)

    Ghosh, Diptimoy

    2013-12-01

    The lighter mass eigenstate (t˜1) of the two top squarks, the scalar superpartners of the top quark, is extremely difficult to discover if it is almost degenerate with the lightest neutralino (χ˜10), the lightest stable supersymmetric particle in the R-parity conserving supersymmetry. The current experimental bound on t˜1 mass in this scenario stands only around 200 GeV. For such a light t˜1, the heavier top squark (t˜2) can also be around the TeV scale. Moreover, the high value of the Higgs (h) mass prefers the left- and right-handed top squarks to be highly mixed, allowing the possibility of a considerable branching ratio for t˜2→t˜1h and t˜2→t˜1Z. In this paper, we explore the above possibility together with the pair production of t˜2 t˜2*, giving rise to the spectacular diboson+missing transverse energy final state. For an approximately 1 TeV t˜2 and a few hundred GeV t˜1 the final state particles can be moderately boosted, which encourages us to propose a novel search strategy employing the jet substructure technique to tag the boosted h and Z. The reconstruction of the h and Z momenta also allows us to construct the stransverse mass MT2, providing an additional efficient handle to fight the backgrounds. We show that a 4-5σ signal can be observed at the 14 TeV LHC for ˜1TeV t˜2 with 100fb-1 integrated luminosity.

  10. Rare top quark decays in extended models

    International Nuclear Information System (INIS)

    Gaitan, R.; Miranda, O. G.; Cabral-Rosetti, L. G.

    2006-01-01

    Flavor changing neutral currents (FCNC) decays t → H0 + c, t → Z + c, and H0 → t + c-bar are discussed in the context of Alternative Left-Right symmetric Models (ALRM) with extra isosinglet heavy fermions where FCNC decays may take place at tree-level and are only suppressed by the mixing between ordinary top and charm quarks, which is poorly constraint by current experimental values. The non-manifest case is also briefly discussed

  11. Controlling - a useful tool for top management

    OpenAIRE

    Grigorut Cornel; Grigorut Lavinia-Maria

    2012-01-01

    Controlling outlines business policy of an enterprise, the term derives from an English word - to control - control, managing, setting rules and directing. The controller's duty is to serve the management as an economic navigator and to ensure that the company's ship reaches its profit targets. The controller has to be sure that he or she has an organizational support from the top management. It was suggested to establish the controlling department which can be applied to the systems of econo...

  12. Modeling Electrolytically Top-Gated Graphene

    Directory of Open Access Journals (Sweden)

    Mišković ZL

    2010-01-01

    Full Text Available Abstract We investigate doping of a single-layer graphene in the presence of electrolytic top gating. The interfacial phenomenon is modeled using a modified Poisson–Boltzmann equation for an aqueous solution of simple salt. We demonstrate both the sensitivity of graphene’s doping levels to the salt concentration and the importance of quantum capacitance that arises due to the smallness of the Debye screening length in the electrolyte.

  13. Charm, Beauty and Top at HERA

    International Nuclear Information System (INIS)

    Behnke, O.; Geiser, A.; Lisovyi, M.

    2015-06-01

    Results on open charm and beauty production and on the search for top production in high-energy electron-proton collisions at HERA are reviewed. This includes a discussion of relevant theoretical aspects, a summary of the available measurements and measurement techniques, and their impact on improved understanding of QCD and its parameters, such as parton density functions and charm- and beauty-quark masses. The impact of these results on measurements at the LHC and elsewhere is also addressed.

  14. INNOVATIVE MARKETING STRATEGIES IN TOP MOST COMPANIES

    OpenAIRE

    Sonia*

    2018-01-01

    This Research Study looks at various innovative marketing strategies used by our top most companies .Marketing strategies is a long term, forward looking approach to planning with the fundamental goal achieving a sustainable competitive advantage. Overall approach of this paper is to create a link between growth rate of companies and new marketing strategies. Good marketing is no accident, It is both an art and a science and it results from careful planning and execution using state-of-the-ar...

  15. Anatomy of top 100 upstream players

    International Nuclear Information System (INIS)

    Burk, V.A.

    1992-01-01

    A brief review is given of a recent survey of the top one hundred upstream oil and gas companies which file financial data with the US Securities and Exchange Commission. The analysis indicates the increasing globalisation of the industry with exploration and development spending increasing dramatically outside the US. To survive, companies must operate as efficient low cost finders and producers of oil and gas and anticipate and meet changing market demands quickly. (UK)

  16. Top quark decays in extended models

    International Nuclear Information System (INIS)

    Gaitan, R.; Cabral-Rosetti, L.G.

    2011-01-01

    We evaluate the FCNC decays t → H 0 + c at tree-level and t → γ + c at one-loop level in the context of Alternative Left-Right symmetric Models (ALRM) with extra isosinglet heavy fermions; in the first case, FCNC decays occurs at tree-level and they are only suppressed by the mixing between ordinary top and charm quarks. (author)

  17. Status of the DO top search

    International Nuclear Information System (INIS)

    Li-Demarteau, Q.

    1994-09-01

    Preliminary new results on the top quark search with the DO experiment in bar pp collisions at √s = 1.8 TeV for an integrated luminosity of 15.2 ± 1.8 pb -1 are reported. In this new analysis, which is optimized for high mass top search, a total of seven candidate events in the electron and muon dilepton decay channels (t bar t → eμ, ee and μμ), single lepton decay channels (t bar t → e + jets and t bar t → μ + jets) without b tagging and single electron decay channel (t bar t → e + jets) with b tagging have been observed. The estimated background is 4.7 ± 1.0 events. If we assume the top quark has a mass of 180 GeV/c 2 , a t bar t production cross section of 3.2 ± 3.9 pb with upper limit of 13 pb at 95% C.L. is obtained

  18. Observation of Single Top Quark Production

    Energy Technology Data Exchange (ETDEWEB)

    Gerber, Cecilia E.; /Illinois U., Chicago

    2009-09-01

    The author reports on the observation of electroweak production of single top quarks in p{bar p} collisions at {radical}s = 1.96 Tev using 2.3 fb{sup -1} of data collected with the D0 detector at the fermilab Tevatron Collider. Using events containing an isolated electron or muon, missing transverse energy, two, three or four jets, with one or two of them identified as originating from the fragmentation of a b quark, the measured cross section for the process p{bar p} {yields} tb + X, tqb + X is 3.94 {+-} 0.88 pb (for a top quark mass of 170 GeV). the probability to measure a cross section at this value or higher in the absence of signal is 2.5 x 10{sup -7}, corresponding to a 5.0 standard deviation significance. Using the same dataset, the measured cross sections for the t- and the s-channel processes when determined simultaneously with no assumption on their relative production rate are 3.14{sub -0.80}{sup +0.94} pb and 1.05 {+-} 0.81 pb respectively, consistent with standard model expectations. The measured t-channel cross section has a significance of 4.8 standard deviations, representing the first evidence for the production of an individual single top process to be detected.

  19. Quantum coherence, top transverse polarisation and the Tevatron asymmetry $A_{FB}^\\ell$

    CERN Document Server

    Aguilar-Saavedra, J A

    2014-01-01

    We revisit the relation between the asymmetries $A_{FB}$ and $A_{FB}^\\ell$ in $t \\bar t$ production at the Tevatron, using as new physics benchmark a colour octet. We find that $A_{FB}^\\ell$ receives large contributions from the interference between $\\lambda = \\pm 1/2$ top helicity states, which has been ignored in some of the previous literature on the subject. The omission of these contributions results in a severe underestimation of the asymmetry, around $1/2$ and $1/50$ of the true value for right-handed and left-handed top couplings to the octet, respectively. Interference effects are closely related to a $\\mathcal{O}(1)$ transverse top polarisation, as yet not considered in this context.

  20. Dynamics of a cliff top dune

    Science.gov (United States)

    Rasmussen, K. R.

    2012-12-01

    Morphological changes during more than 100 years have been investigated for a cliff-top dune complex at Rubjerg at the Danish North Sea coast. Here the lower 50 m of the cliff front is composed of Pleistocene steeply inclined floes of silt and clay with coarse sand in between which gives it a saw-tooth appearance. On top of this the dunes are found for several kilometres along the coastline. Due to erosion by the North Sea the cliff has retreated about 120 m between approximately 1880 and 1970 as indicated from two national surveys, and recent GPS-surveys indicate that erosion is continuing at a similar rate. Nevertheless the cliff top dune complex has survived, but its morphology has undergone some changed. The old maps indicate that around 1880 the dune complex was composed of several up to about 20 m high dunes streamlined in the East-West direction which is parallel to the prevailing wind direction. When protective planting started during the first half of the 20th Century the cliff top dunes gradually merged together forming a narrow, tall ridge parallel to the shore line with the highest part reaching about 90 m near 1970. In 1993 the highest points along the ridge was almost 95 m high, but then the protective planting was considerably reduced and recent annual GPS-surveys indicate that the dunes respond quickly to this by changing their morphology towards the original appearance. It is remarkable that despite the mass wasting caused by the constant erosion of the cliff front the dunes have remained more or less intact. Theoretical studies of hill flow indicate given the proper geometry of the cliff then suspension of even coarse grains can be a very effective agent for carrying sand from the exposed parts of the cliff front to and beyond the cliff-top. Mostly the sand grains are deposited within some hundred meters downwind of the cliff dune while silt is often carried more than 10 km inland. Field observations indicate that where the dislodged floes and

  1. Communication received from South Africa

    International Nuclear Information System (INIS)

    1984-02-01

    The document reproduces the press release with a statement by Dr. J.W.L. de Villiers, Executive Chairman of the Atomic Energy Corporation of South Africa Limited, issued on 31 January 1984 and included in the letter received by the Director General of the IAEA from the Resident Representative of South Africa to the Agency on 31 January 1984. This statement refers to the transfer of nuclear material equipment and technology by South Africa to other countries and the Non-Proliferation Treaty

  2. Absorption Efficiency of Receiving Antennas

    DEFF Research Database (Denmark)

    Andersen, Jørgen Bach; Frandsen, Aksel

    2005-01-01

    A receiving antenna with a matched load will always scatter some power. This paper sets an upper and a lower bound on the absorption efficiency (absorbed power over sum of absorbed and scattered powers), which lies between 0 and 100% depending on the directivities of the antenna and scatter...... patterns. It can approach 100% as closely as desired, although in practice this may not be an attractive solution. An example with a small endfire array of dipoles shows an efficiency of 93%. Several examples of small conical horn antennas are also given, and they all have absorption efficiencies less than...

  3. Computational engineering

    CERN Document Server

    2014-01-01

    The book presents state-of-the-art works in computational engineering. Focus is on mathematical modeling, numerical simulation, experimental validation and visualization in engineering sciences. In particular, the following topics are presented: constitutive models and their implementation into finite element codes, numerical models in nonlinear elasto-dynamics including seismic excitations, multiphase models in structural engineering and multiscale models of materials systems, sensitivity and reliability analysis of engineering structures, the application of scientific computing in urban water management and hydraulic engineering, and the application of genetic algorithms for the registration of laser scanner point clouds.

  4. Architectural Engineers

    DEFF Research Database (Denmark)

    Petersen, Rikke Premer

    engineering is addresses from two perspectives – as an educational response and an occupational constellation. Architecture and engineering are two of the traditional design professions and they frequently meet in the occupational setting, but at educational institutions they remain largely estranged....... The paper builds on a multi-sited study of an architectural engineering program at the Technical University of Denmark and an architectural engineering team within an international engineering consultancy based on Denmark. They are both responding to new tendencies within the building industry where...... the role of engineers and architects increasingly overlap during the design process, but their approaches reflect different perceptions of the consequences. The paper discusses some of the challenges that design education, not only within engineering, is facing today: young designers must be equipped...

  5. Tissue engineering

    CERN Document Server

    Fisher, John P; Bronzino, Joseph D

    2007-01-01

    Increasingly viewed as the future of medicine, the field of tissue engineering is still in its infancy. As evidenced in both the scientific and popular press, there exists considerable excitement surrounding the strategy of regenerative medicine. To achieve its highest potential, a series of technological advances must be made. Putting the numerous breakthroughs made in this field into a broad context, Tissue Engineering disseminates current thinking on the development of engineered tissues. Divided into three sections, the book covers the fundamentals of tissue engineering, enabling technologies, and tissue engineering applications. It examines the properties of stem cells, primary cells, growth factors, and extracellular matrix as well as their impact on the development of tissue engineered devices. Contributions focus on those strategies typically incorporated into tissue engineered devices or utilized in their development, including scaffolds, nanocomposites, bioreactors, drug delivery systems, and gene t...

  6. Highlights of top quark cross-section measurements at ATLAS

    CERN Document Server

    Bielski, Rafal; The ATLAS collaboration

    2017-01-01

    Measurements of inclusive and differential top-quark production cross sections in proton-proton collisions with the ATLAS detector at the Large Hadron Collider are presented at a center of mass energy of 8 TeV and 13 TeV. The inclusive measurements of top quark pair and single top quark production reach high precision and are compared to the best available theoretical calculations. Differential measurements of the kinematic properties of top quark events are also discussed. These measurements, including results using boosted top quarks, probe our understanding of top quark production in the TeV regime.

  7. Deep-learning top taggers or the end of QCD?

    Energy Technology Data Exchange (ETDEWEB)

    Kasieczka, Gregor [Institute for Particle Physics, ETH Zürich,Otto-Stern-Weg 5, Zürich (Switzerland); Plehn, Tilman [Institut für Theoretische Physik, Universität Heidelberg,Philosophenweg 16, Heidelberg (Germany); Russell, Michael [School of Physics and Astronomy, University of Glasgow,Glasgow G12 8QQ, Glasgow (United Kingdom); Schell, Torben [Institut für Theoretische Physik, Universität Heidelberg,Philosophenweg 16, Heidelberg (Germany)

    2017-05-02

    Machine learning based on convolutional neural networks can be used to study jet images from the LHC. Top tagging in fat jets offers a well-defined framework to establish our DeepTop approach and compare its performance to QCD-based top taggers. We first optimize a network architecture to identify top quarks in Monte Carlo simulations of the Standard Model production channel. Using standard fat jets we then compare its performance to a multivariate QCD-based top tagger. We find that both approaches lead to comparable performance, establishing convolutional networks as a promising new approach for multivariate hypothesis-based top tagging.

  8. Toiduainetööstuse TOP aastal 2006 / Rivo Sarapik

    Index Scriptorium Estoniae

    Sarapik, Rivo, 1981-

    2007-01-01

    Ilmunud ka: Delovõje Vedomosti : Promõshlennost 17. okt. lk. 12-13. Edukamad toiduainetööstuse tootjad 2006. aastal. Vt. samas: Toiduainetööstuse üld- ja finantsandmed; Käibe TOP 5; Käibe kasvu TOP 5; Kasumi TOP 5; Kasumi kasvu TOP 5; Rentaabluse TOP 5; Omakapitali tootlikkuse TOP 5; Ketlin Priilinn:Võru Juust tipus emafirma abiga. Kommenteerib Tiia Karu. Diagramm; AS Tere tõuseb raske töö toel. Kommenteerib Aivar Häelm. Diagramm; Maag ajab jonnakusega oma asja. Diagramm

  9. Deep-learning top taggers or the end of QCD?

    International Nuclear Information System (INIS)

    Kasieczka, Gregor; Plehn, Tilman; Russell, Michael; Schell, Torben

    2017-01-01

    Machine learning based on convolutional neural networks can be used to study jet images from the LHC. Top tagging in fat jets offers a well-defined framework to establish our DeepTop approach and compare its performance to QCD-based top taggers. We first optimize a network architecture to identify top quarks in Monte Carlo simulations of the Standard Model production channel. Using standard fat jets we then compare its performance to a multivariate QCD-based top tagger. We find that both approaches lead to comparable performance, establishing convolutional networks as a promising new approach for multivariate hypothesis-based top tagging.

  10. Top wealth shares in Australia 1915-2012

    OpenAIRE

    Katic, Pamela; Leigh, Andrew

    2016-01-01

    Combining data from surveys, inheritance tax records, and rich lists, we estimate top wealth shares for Australia from World War I until the present day. We find that the top 1 percent share declined by two-thirds from 1915 until the late 1960s, and rose from the late 1970s to 2010. The recent increase is sharpest at the top of the distribution, with the top 0.001 percent wealth share tripling from 1984 to 2012. The trend in top wealth shares is similar to that in Australian top income shares...

  11. Solar receiver with integrated optics

    Science.gov (United States)

    Jiang, Lun; Winston, Roland

    2012-10-01

    The current challenge for PV/Thermal (PV/T) systems is the reduction of radiation heat loss. Compared to solar thermal selective coating, the solar cells cannot be used as an efficient thermal absorber due to their large emissivity of the encapsulation material. Many commercial PV/T products therefore require a high concentration (more than 10x) to reach an acceptable thermal efficiency for their receivers. Such a concentration system inevitably has to track or semi-track, which induces additional cost and collects only the direct radiation from the sun. We propose a new PV/T design using a vacuum encapsulated thin film cell to solve this problem. The proposed design also collects the diffuse sun light efficiently by using an external compound parabolic concentrator (XCPC). Since the transparent electrode (TCO) of thin film cell is inherently transparent in visible light and reflective beyond infrared, this design uses this layer instead of the conventional solar cell encapsulation as the outmost heat loss surface. By integrating such a vacuum design with a tube shaped absorber, we reduce the complexity of conducting the heat energy and electricity out of the device. A low concentration standalone non-tracking solar collector is proposed in this paper. We also analyzed the thermosyphon system configuration using heat transfer and ray tracing models. The economics of such a receiver are presented.

  12. Broadband direct RF digitization receivers

    CERN Document Server

    Jamin, Olivier

    2014-01-01

    This book discusses the trade-offs involved in designing direct RF digitization receivers for the radio frequency and digital signal processing domains.  A system-level framework is developed, quantifying the relevant impairments of the signal processing chain, through a comprehensive system-level analysis.  Special focus is given to noise analysis (thermal noise, quantization noise, saturation noise, signal-dependent noise), broadband non-linear distortion analysis, including the impact of the sampling strategy (low-pass, band-pass), analysis of time-interleaved ADC channel mismatches, sampling clock purity and digital channel selection. The system-level framework described is applied to the design of a cable multi-channel RF direct digitization receiver. An optimum RF signal conditioning, and some algorithms (automatic gain control loop, RF front-end amplitude equalization control loop) are used to relax the requirements of a 2.7GHz 11-bit ADC. A two-chip implementation is presented, using BiCMOS and 65nm...

  13. Trends in Ph.D. Productivity and Diversity in Top-50 U.S. Chemistry Departments: An Institutional Analysis

    Science.gov (United States)

    Laursen, Sandra L.; Weston, Timothy J.

    2014-01-01

    The education of doctoral chemists contributes to the chemical research enterprise and thus to innovation as an engine of the economy. This quantitative analysis describes trends in the production and diversity of chemistry Ph.D. degrees in the top-50 U.S. Ph.D.-granting departments in the past two decades. Time series data for individual…

  14. Emplacement engineering

    Energy Technology Data Exchange (ETDEWEB)

    Hill, Ernest E [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

    1970-05-01

    Emplacement Engineering can be defined as that portion of a nuclear explosive project that is concerned with the emplacement of the explosive. This definition would then include virtually everything except the design and fabrication of the explosive and the post-shot-effects program. For future commercial application, the post-shot-effects program will essentially disappear. This emplacement portion of a nuclear explosive project constitutes a large fraction of the total project cost, but it has largely been overshadowed by the explosive and explosive-effects portions. As we move into commercial applications. Emplacement Engineering must receive more attention from both industry and government. To place emplacement costs in their proper relationship with total projects costs, we have performed a study of commercial underground nuclear explosive applications such as gas stimulation. Although there are many intangibles in such a study, we have been able to at least obtain some feel for the relative fractional costs of the non-explosive costs compared with the explosive costs. This study involved estimating the cost elements for applications using a single explosive at 5,000 ft, 10,000 ft, and 15,000 ft. For each depth, the cost estimates were made for a range of emplacement hole and explosive diameters. Results of these estimates for explosive-related costs, hole-related costs, and total costs are shown for the three depths. Note that the explosive package outside diameter is assumed as 2 inches less than the hole (or casing) inside diameter for all cases. For the 5,000-ft application the explosive-related costs dominate, and of particular importance is the indicated diameter for minimum total cost which occurs at approximately a 17.5-in. hole (15.5-in. explosive). The hole-related costs are in 'the same range as the explosive-related costs for the 10,000-ft application. For this case, the minimum total cost occurs at approximately a 14-in. hole (12-in. explosive

  15. Microsurgery: the top 50 classic papers in plastic surgery: a citation analysis.

    Science.gov (United States)

    Joyce, Cormac Weekes; Carroll, Sean Michael

    2014-03-01

    The number of citations that a published article has received reflects the importance of the paper in the particular area of practice. In microsurgery, thus far, which journal articles are cited most frequently is unknown. The purpose of this study was to identify and analyze the characteristics of the top 50 papers in the field of microsurgery in the plastic surgery literature. The 50 most cited papers published in high impact plastic surgery and microsurgery journals were identified. The articles were ranked in the order of the number of citations received. These 50 classic papers were analyzed for article type, journal distribution, and geographic and institutional origin. Six international journals contributed to the top 50 papers in microsurgery. The most cited paper reported on the early use of the vascularized bone graft and was cited 116 times. The top 50 papers originated from just 10 countries with the United States producing the most. The Preston and Northcote Community Hospital, Melbourne published 5 papers and this was the most productive institution in the top 50. These papers represent many important milestones in the relatively short history of microsurgery. Furthermore, our citation analysis provides useful information to budding authors as to what makes a paper attain a "classic" status.

  16. Engineering metallic nanostructures for plasmonics and nanophotonics

    Science.gov (United States)

    Lindquist, Nathan C.; Nagpal, Prashant; McPeak, Kevin M.; Norris, David J.; Oh, Sang-Hyun

    2012-03-01

    Metallic nanostructures now play an important role in many applications. In particular, for the emerging fields of plasmonics and nanophotonics, the ability to engineer metals on nanometric scales allows the development of new devices and the study of exciting physics. This review focuses on top-down nanofabrication techniques for engineering metallic nanostructures, along with computational and experimental characterization techniques. A variety of current and emerging applications are also covered.

  17. The race to decipher the top secrets of TOP mRNAs.

    Science.gov (United States)

    Meyuhas, Oded; Kahan, Tamar

    2015-07-01

    Cells encountering hostile growth conditions, like those residing in the middle of a newly developing solid tumor, conserve resources and energy by downregulating protein synthesis. One mechanism in this response is the translational repression of multiple mRNAs that encode components of the translational apparatus. This coordinated translational control is carried through a common cis-regulatory element, the 5' Terminal OligoPyrimidine motif (5'TOP), after which these mRNAs are referred to as TOP mRNAs. Subsequent to the initial structural and functional characterization of members of this family, the research of TOP mRNAs has progressed in three major directions: a) delineating the landscape of the family; b) establishing the pathways that transduce stress cues into selective translational repression; and c) attempting to decipher the most proximal trans-acting factor(s) and defining its mode of action--a repressor or activator. The present chapter critically reviews the development in these three avenues of research with a special emphasis on the two "top secrets" of the TOP mRNA family: the scope of its members and the identity of the proximal cellular regulator(s). This article is part of a Special Issue entitled: Translation and Cancer. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Stress analysis of longwall top coal caving

    Energy Technology Data Exchange (ETDEWEB)

    Alehossein, H.; Poulsen, B.A. [CSIRO Exploration & Mining, Brisbane, Qld. (Australia)

    2010-01-15

    Longwall top coal caving (LTCC) is a relatively new method of mining thick coal seams that is currently achieving high productivity and efficiency. The technique is similar to traditional longwall mining in that a cutting head slices coal from the lower section of the coal seam onto a conveyor belt installed in front of the hydraulic support near the cutting face. In modern LTCC an additional rear conveyor belt is located behind the support, to which the flow of the caved coal from the upper part of the seam can be controlled by a moveable flipper attached to the canopy of the support. The mining method relies on the fracturing of the top coal by the front abutment pressure to achieve satisfactory caving into the rear conveyor. This paper develops a yield and caveability criterion based on in situ conditions in the top coal in advance of the mining face (yield) and behind the supports (caveability). Yielding and caving effects are combined into one single number called caving number (CN), which is the multiplication result of caving factor (CF) and yield factor (YF). Analytical derivations are based on in situ stress conditions, Mohr-Coulomb and/or Hoek-Brown rock failure criteria and an on-associated elastoplastic strain softening material behaviour. The yield and caveability criteria are in agreement with results from both numerical studies and mine data. The caving number is normalised to mining conditions of a reference Chinese mine (LMX mine) and is used to assess LTCC performance at fourteen other Chinese working longwalls that have had varying success with the LTCC technology. As a predictive model, results of this analytical/numerical study are useful to assess the potential success of caving in new LTCC operations and in different mining conditions.

  19. How Accurate Is the Science News We Receive from the Mass Media?

    Science.gov (United States)

    Molitor, Fred

    One day before a health study appeared in the "New England Journal of Medicine (NEJM)" the study was reported media. A content analysis of the top 5 national newspapers examined the accuracy of this news reporting. The NEJM study found that men who took aspirin had 50% fewer heart attacks than men who received a placebo. Analysis of the…

  20. China. Top Sector Energy. Sustainable Building. Opportunities for Dutch companies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-08-15

    For China, sustainable design is necessary for controlling energy usage in crowded and constantly expanding urban areas. It is well known that China is the world's biggest construction market. Nearly half of the new buildings annually constructed worldwide are located in China by 2015. However, only about 4% of these are built according to energy efficiency standards. China's construction market will by 2020 account for 40% of the country's total energy consumption. While it contributes 15% of the world's GDP, China consumes 30% of the earth's steel and half its concrete. On top of which, buildings in China consume a third of the country's increasingly endangered water supplies. Recent research showed that almost half of the national energy consumption has been used for construction related purposes. Of existing buildings, a huge amount needs sustainable redesign and retrofitting technologies.Chinese government has recognized the urgency of widely implementing sustainable buildings. As a result, a national 3-star China National Green Building rating system has been launched in 2006. Yet the Chinese green building revolution is still in its infancy. Main problems are, amongst others, low level of regulations and standards, problematic implementations at local level, lack of awareness and transparency in related public and private sector, lack of expertise of integrated sustainable building design and construction among engineers, designers and constructors. It is also to be expected that more aggressive energy saving and environmental protection targets will be set by the 12th Five Year Plan. Promote green buildings will be one of the top priorities in China's swift urbanization process with focus on saving land, energy, water and materials. Chinese government has recognized the urgency of widely implementing sustainable buildings. Yet the Chinese green building revolution is still in its infancy. Under this framework, the following areas will offer business

  1. The Cherenkov Telescope Array Observatory: top level use cases

    Science.gov (United States)

    Bulgarelli, A.; Kosack, K.; Hinton, J.; Tosti, G.; Schwanke, U.; Schwarz, J.; Colomé, P.; Conforti, V.; Khelifi, B.; Goullon, J.; Ong, R.; Markoff, S.; Contreras, J. L.; Lucarelli, F.; Antonelli, L. A.; Bigongiari, C.; Boisson, C.; Bosnjak, Z.; Brau-Nogué, S.; Carosi, A.; Chen, A.; Cotter, G.; Covino, S.; Daniel, M.; De Cesare, G.; de Ona Wilhelmi, E.; Della Volpe, M.; Di Pierro, F.; Fioretti, V.; Füßling, M.; Garczarczyk, M.; Gaug, M.; Glicenstein, J. F.; Goldoni, P.; Götz, D.; Grandi, P.; Heller, M.; Hermann, G.; Inoue, S.; Knödlseder, J.; Lenain, J.-P.; Lindfors, E.; Lombardi, S.; Luque-Escamilla, P.; Maier, G.; Marisaldi, M.; Mundell, C.; Neyroud, N.; Noda, K.; O'Brien, P.; Petrucci, P. O.; Martí Ribas, J.; Ribó, M.; Rodriguez, J.; Romano, P.; Schmid, J.; Serre, N.; Sol, H.; Schussler, F.; Stamerra, A.; Stolarczyk, T.; Vandenbrouck, J.; Vercellone, S.; Vergani, S.; Zech, A.; Zoli, A.

    2016-08-01

    Today the scientific community is facing an increasing complexity of the scientific projects, from both a technological and a management point of view. The reason for this is in the advance of science itself, where new experiments with unprecedented levels of accuracy, precision and coverage (time and spatial) are realised. Astronomy is one of the fields of the physical sciences where a strong interaction between the scientists, the instrument and software developers is necessary to achieve the goals of any Big Science Project. The Cherenkov Telescope Array (CTA) will be the largest ground-based very high-energy gamma-ray observatory of the next decades. To achieve the full potential of the CTA Observatory, the system must be put into place to enable users to operate the telescopes productively. The software will cover all stages of the CTA system, from the preparation of the observing proposals to the final data reduction, and must also fit into the overall system. Scientists, engineers, operators and others will use the system to operate the Observatory, hence they should be involved in the design process from the beginning. We have organised a workgroup and a workflow for the definition of the CTA Top Level Use Cases in the context of the Requirement Management activities of the CTA Observatory. Scientists, instrument and software developers are collaborating and sharing information to provide a common and general understanding of the Observatory from a functional point of view. Scientists that will use the CTA Observatory will provide mainly Science Driven Use Cases, whereas software engineers will subsequently provide more detailed Use Cases, comments and feedbacks. The main purposes are to define observing modes and strategies, and to provide a framework for the flow down of the Use Cases and requirements to check missing requirements and the already developed Use-Case models at CTA sub-system level. Use Cases will also provide the basis for the definition of

  2. China. Top Sector Energy. Sustainable Building. Opportunities for Dutch companies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-08-15

    For China, sustainable design is necessary for controlling energy usage in crowded and constantly expanding urban areas. It is well known that China is the world's biggest construction market. Nearly half of the new buildings annually constructed worldwide are located in China by 2015. However, only about 4% of these are built according to energy efficiency standards. China's construction market will by 2020 account for 40% of the country's total energy consumption. While it contributes 15% of the world's GDP, China consumes 30% of the earth's steel and half its concrete. On top of which, buildings in China consume a third of the country's increasingly endangered water supplies. Recent research showed that almost half of the national energy consumption has been used for construction related purposes. Of existing buildings, a huge amount needs sustainable redesign and retrofitting technologies.Chinese government has recognized the urgency of widely implementing sustainable buildings. As a result, a national 3-star China National Green Building rating system has been launched in 2006. Yet the Chinese green building revolution is still in its infancy. Main problems are, amongst others, low level of regulations and standards, problematic implementations at local level, lack of awareness and transparency in related public and private sector, lack of expertise of integrated sustainable building design and construction among engineers, designers and constructors. It is also to be expected that more aggressive energy saving and environmental protection targets will be set by the 12th Five Year Plan. Promote green buildings will be one of the top priorities in China's swift urbanization process with focus on saving land, energy, water and materials. Chinese government has recognized the urgency of widely implementing sustainable buildings. Yet the Chinese green building revolution is still in its infancy. Under this framework, the

  3. Architecture of top down, parallel pattern recognition system TOPS and its application to the MR head images

    International Nuclear Information System (INIS)

    Matsunoshita, Jun-ichi; Akamatsu, Shigeo; Yamamoto, Shinji.

    1993-01-01

    This paper describes about the system architecture of a new image recognition system TOPS (top-down parallel pattern recognition system), and its application to the automatic extraction of brain organs (cerebrum, cerebellum, brain stem) from 3D-MRI images. Main concepts of TOPS are as follows: (1) TOPS is the top-down type recognition system, which allows parallel models in each level of hierarchy structure. (2) TOPS allows parallel image processing algorithms for one purpose (for example, for extraction of one special organ). This results in multiple candidates for one purpose, and judgment to get unique solution for it will be made at upper level of hierarchy structure. (author)

  4. Heat receivers for solar dynamic space power systems

    Science.gov (United States)

    Perez-Davis, Marla Esther

    A review of state-of-the-art technology is presented and discussed for phase change materials. Some of the advanced solar dynamic designs developed as part of the Advanced Heat Receiver Conceptual Design Study performed for LeRC are discussed. The heat receivers are analyzed and several recommendations are proposed, including two new concepts. The first concept evaluated the effect of tube geometries inside the heat receiver. It was found that a triangular configuration would provide better heat transfer to the working fluid, although not necessarily with a reduction in receiver size. A sensible heat receiver considered in this study uses vapor grown graphite fiber-carbon (VGCF/C) composite as the thermal storage media and was designed for a 7 kW Brayton engine. The proposed heat receiver stores the required energy to power the system during eclipse in the VGCF/C composite. The heat receiver analysis was conducted through the Systems Improved Numerical Differencing Analyzer and Fluid Integrator (SINDA) software package. The proposed heat receiver compares well with other latent and advanced sensible heat receivers while avoiding the problems associated with latent heat storage salts and liquid metal heat pipes. The weight and size of the system can be optimized by changes in geometry and technology advances for this new material. In addition to the new concepts, the effect of atomic oxygen on several materials is reviewed. A test was conducted for atomic oxygen attack on boron nitride, which experienced a negligible mass loss when exposed to an atomic oxygen fluence of 5 x 10 exp 21 atoms/sq cm. This material could be used to substitute the graphite aperture plate of the heat receiver.

  5. CERN physicist receives Einstein Medal

    CERN Multimedia

    2006-01-01

    On 29 June the CERN theorist Gabriele Veneziano was awarded the prestigious Albert Einstein Medal for significant contributions to the understanding of string theory. This award is given by the Albert Einstein Society in Bern to individuals whose scientific contributions relate to the work of Einstein. Former recipients include exceptional physicists such as Murray Gell-Mann last year, but also Stephen Hawking and Victor Weisskopf. Gabriele Veneziano, a member of the integrated CERN Theory Team since 1977, led the Theory Division from 1994 to 1997 and has already received many prestigious prizes for his outstanding work, including the Enrico Fermi Prize (see CERN Courier, November 2005), the Dannie Heineman Prize for mathematical physics of the American Physical Society in 2004 (see Bulletin No. 47/2003), and the I. Ya. Pomeranchuk Prize of the Institute of Theoretical and Experimental Physics (Moscow) in 1999.

  6. Top tagging with deep neural networks [Vidyo

    CERN Multimedia

    CERN. Geneva

    2017-01-01

    Recent literature on deep neural networks for top tagging has focussed on image based techniques or multivariate approaches using high level jet substructure variables. Here, we take a sequential approach to this task by using anordered sequence of energy deposits as training inputs. Unlike previous approaches, this strategy does not result in a loss of information during pixelization or the calculation of high level features. We also propose new preprocessing methods that do not alter key physical quantities such as jet mass. We compare the performance of this approach to standard tagging techniques and present results evaluating the robustness of the neural network to pileup.

  7. Resonance in a Cone-Topped Tube

    Directory of Open Access Journals (Sweden)

    Angus Cheng-Huan Chia

    2011-06-01

    Full Text Available The relationship between ratio of the upper opening diameter of a cone-topped cylinder to the cylinder diameter,and the ratio of the length of the air column to resonant period was examined. Plastic cones with upper openings ranging from 1.3 cm to 3.6 cm and tuning forks with frequencies ranging from 261.6 Hz to 523.3 Hz were used. The transition from a standing wave in a cylindrical column to a Helmholtz-type resonance in a resonant cavity with a narrow opening was observed.

  8. SM+Top at the LHC

    CERN Document Server

    McCarthy, Tom; The ATLAS collaboration

    2018-01-01

    This overview talk highlights some of the latest results by the ATLAS, CMS & LHCb collaborations. A particular focus is placed on some of the rarer Standard Model processes which have recently become accessible with the large set of proton-proton collision data collected during the successful second run of the LHC at $\\sqrt{s}$ = 13 TeV. Searches and cross-section measurements involving top quark signatures are given prominence, as well as those targeting highly boosted objects such as SM W/Z and Higgs bosons, and which consequently feature large-R jets and substructure techniques.

  9. A top-face-sway electromagnetic micromotor

    Science.gov (United States)

    Liang, Jingqiu; Le, Zichun; Yao, Jinsong; Wu, Zhiyong; Jia, Hongguang; Wu, Yihui; Jia, Zhi; 1, Qiongying Lu; Xuan, Ming; Wang, Lijun

    2003-04-01

    In this paper, the structure of a top-face-sway electromagnetic micromotor and its principle, fabrication and performance are introduced. A combination of the electromagnetic actuating and the planetary reducing provides this micromotor an advantage of low rotational speed and high torque. In addition, since a flexible coupling absorbs the sway and only outputs rotation, it gives this micromotor a balanced output. The dimension of the micromotor is 5 mm. Its rotation speed has a range of 20 - 860 rpm, and its driving current is 300 mA. The output torque of the micromotor is measured to be 13.0 ?Nm.

  10. Measurement of the top quark mass

    Energy Technology Data Exchange (ETDEWEB)

    Hsieh, Tzu-Chung Frank [Univ. of Michigan, Ann Arbor, MI (United States)

    1998-01-01

    From p$\\bar{p}$ collisions at √s = 1.8 TeV in the Fermilab Tevatron collider, top quarks are produced predominantly in t$\\bar{t}$ pairs. After applying a sophisticated event selection to the ≈ 100pb -1 data recorded by the D0 detector, we have 35 t$\\bar{t}$ → e(μ) + jets candidates with the backgrounds estimated to be 16.3 ± 2.2. We perform a kinematically constrained fit for individual events, and the results are input to a likelihood analysis.

  11. Top quark asymmetry and dijet resonances

    CERN Document Server

    Jung, Sunghoon; Wells, James D.

    2011-01-01

    CDF recently reported an anomaly in the $m_{jj}$ distribution of dijet events produced in association with a $W$ boson. If this anomaly is associated with a new flavor conserving vector resonance, $V$, one might have expected to observe effects in the analogous $m_{jj}$ distribution produced in association with a $\\gamma$. No such excess is observed. A single $u-t-V$ flavor changing coupling, however, can contribute to the $m_{jj}$ anomaly while being consistent with other resonance searches. Furthermore, it gives a potential explanation of the observed forward-backward asymmetry in top quark production.

  12. TOP MANAGEMENT SUPPORT TO CLIMATE CHANGE

    OpenAIRE

    Siqueira de Morais Neto; Maurício Fernandes Pereira

    2014-01-01

    The article theme is the Corporate Climate Change and aims to identify whether there is top management support to the companies’ attitudes related to the climate change, with a comparison between two groups of enterprises, “Brazil” and “S&P 500 MZ”, using the Carbon Disclosure Project database. It was used a methodology of a descriptive nature based on secondary data collection, which was done through literature review and the observation of the CDP’s questionnaires. It was observed that 62% ...

  13. Search for anomalous Wtb couplings in single top quark production ...

    Indian Academy of Sciences (India)

    2012-11-08

    Nov 8, 2012 ... Single top quark production provides a unique probe ... our search is improved by dividing our data into six independent analysis ... After the event selection, the expected single top quark contribution is smaller than the.

  14. Board of Directors, Top Management Team and the Developmentof Academic Spin-Off Companies

    OpenAIRE

    Bjørnåli, Ekaterina S.

    2009-01-01

    This dissertation addresses the under-studied area of the role of the top management team (TMT) and board of directors in the development of academic spin-off companies (ASOs) originating from public research institutes. ASO research receives growing attention internationally following the rise in commercialization activities in the vast majority of universities. The studies identify the barriers to and facilitators of ASO formation and growth, which are related to faculty attributes and ince...

  15. Engineering mechanics

    CERN Document Server

    Gross, Dietmar; Schröder, Jörg; Wall, Wolfgang A; Rajapakse, Nimal

    Statics is the first volume of a three-volume textbook on Engineering Mechanics. The authors, using a time-honoured straightforward and flexible approach, present the basic concepts and principles of mechanics in the clearest and simplest form possible to advanced undergraduate engineering students of various disciplines and different educational backgrounds. An important objective of this book is to develop problem solving skills in a systematic manner. Another aim of this volume is to provide engineering students as well as practising engineers with a solid foundation to help them bridge the gap between undergraduate studies on the one hand and advanced courses on mechanics and/or practical engineering problems on the other. The book contains numerous examples, along with their complete solutions. Emphasis is placed upon student participation in problem solving. The contents of the book correspond to the topics normally covered in courses on basic engineering mechanics at universities and colleges. Now in i...

  16. Invisible Engineers

    Science.gov (United States)

    Ohashi, Hideo

    Questionnaire to ask “mention three names of scientists you know” and “three names of engineers you know” was conducted and the answers from 140 adults were analyzed. The results indicated that the image of scientists is represented by Nobel laureates and that of engineers by great inventors like Thomas Edison and industry founders like Soichiro Honda. In order to reveal the image of engineers among young generation, questionnaire was conducted for pupils in middle and high schools. Answers from 1,230 pupils were analyzed and 226 names mentioned as engineers were classified. White votes reached 60%. Engineers who are neither big inventors nor company founders collected less than 1% of named votes. Engineers are astonishingly invisible from young generation. Countermeasures are proposed.

  17. Global engineering

    International Nuclear Information System (INIS)

    Plass, L.

    2001-01-01

    This article considers the challenges posed by the declining orders in the plant engineering and contracting business in Germany, the need to remain competitive, and essential preconditions for mastering the challenge. The change in engineering approach is illustrated by the building of a methanol plant in Argentina by Lurgi with the basic engineering completed in Frankfurt with involvement of key personnel from Poland, completely engineered subsystems from a Brazilian subsupplier, and detailed engineering work in Frankfurt. The production of methanol from natural gas using the LurgiMega/Methanol process is used as a typical example of the industrial plant construction sector. The prerequisites for successful global engineering are listed, and error costs in plant construction, possible savings, and process intensification are discussed

  18. Review of recent top-quark LHC combinations

    CERN Document Server

    Cortiana, Giorgio

    2014-01-01

    A review of recent combinations of top-quark measurements performed at the LHC, by the ATLAS and CMS collaborations, is provided. The typical uncertainty categorisations, and their assumed correlation patterns are presented, together with the results of the combinations of the top-quark pair and single top-quark production cross sections, the top-quark mass, as well as of the $W$ boson polarisation and the charge asymmetry in $t\\bar t$ events.

  19. Highlights of top quark properties measurements at ATLAS

    CERN Document Server

    Barranco Navarro, Laura; The ATLAS collaboration

    2017-01-01

    The top quark is the heaviest known fundamental particle. As it is the only quark that decays before it hadronizes, this gives the unique opportunity to probe the properties of bare quarks. This talk focuses on a few recent precision measurements of top quark properties in production and decay by the ATLAS Collaboration. Measurements of the top quark mass and searches for rare top quark decays are also presented.

  20. Highlights of top quark properties measurements at ATLAS

    CERN Document Server

    Barranco Navarro, Laura; The ATLAS collaboration

    2017-01-01

    The top quark is the heaviest known fundamental particle. As it is the only quark that decays before it hadronizes, this gives the unique opportunity to probe the properties of bare quarks. This talk will focus on a few recent precision measurements of top quark properties in production and decay by the ATLAS Collaboration. Measurements of the top quark mass and searches for rare top quark decays are also presented.

  1. Toponium Tests Of Top-Quark Higgs Bags

    OpenAIRE

    Macpherson, Alick L.; Campbell, Bruce A.

    1993-01-01

    Recently it has been suggested that top quarks, or very massive fourth generation quarks, might surround themselves with a Higgs "bag" of deformation of the Higgs expectation value from its vacuum magnitude. In this paper we address the question of whether such nonlinear Higgs-top interaction effects are subject to experimental test. We first note that if top quarks were necessarily accompanied by Higgs "bags", then top quark weak decay would involve the sudden disruption of the Higgs "bag", ...

  2. Human engineering

    International Nuclear Information System (INIS)

    Yang, Seong Hwan; Park, Bum; Gang, Yeong Sik; Gal, Won Mo; Baek, Seung Ryeol; Choe, Jeong Hwa; Kim, Dae Sung

    2006-07-01

    This book mentions human engineering, which deals with introduction of human engineering, Man-Machine system like system design, and analysis and evaluation of Man-Machine system, data processing and data input, display, system control of man, human mistake and reliability, human measurement and design of working place, human working, hand tool and manual material handling, condition of working circumstance, working management, working analysis, motion analysis working measurement, and working improvement and design in human engineering.

  3. Engineering Electromagnetics

    International Nuclear Information System (INIS)

    Kim, Se Yun

    2009-01-01

    This book deals with engineering electromagnetics. It contains seven chapters, which treats understanding of engineering electromagnetics such as magnet and electron spin, current and a magnetic field and an electromagnetic wave, Essential tool for engineering electromagnetics on rector and scalar, rectangular coordinate system and curl vector, electrostatic field with coulomb rule and method of electric images, Biot-Savart law, Ampere law and magnetic force, Maxwell equation and an electromagnetic wave and reflection and penetration of electromagnetic plane wave.

  4. Information engineering

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, D.N.

    1997-02-01

    The Information Engineering thrust area develops information technology to support the programmatic needs of Lawrence Livermore National Laboratory`s Engineering Directorate. Progress in five programmatic areas are described in separate reports contained herein. These are entitled Three-dimensional Object Creation, Manipulation, and Transport, Zephyr:A Secure Internet-Based Process to Streamline Engineering Procurements, Subcarrier Multiplexing: Optical Network Demonstrations, Parallel Optical Interconnect Technology Demonstration, and Intelligent Automation Architecture.

  5. Software engineering

    CERN Document Server

    Sommerville, Ian

    2010-01-01

    The ninth edition of Software Engineering presents a broad perspective of software engineering, focusing on the processes and techniques fundamental to the creation of reliable, software systems. Increased coverage of agile methods and software reuse, along with coverage of 'traditional' plan-driven software engineering, gives readers the most up-to-date view of the field currently available. Practical case studies, a full set of easy-to-access supplements, and extensive web resources make teaching the course easier than ever.

  6. Measurement of the top quark mass

    International Nuclear Information System (INIS)

    Varnes, E.W.

    1997-01-01

    This dissertation describes the measurement of the top quark mass m t using events recorded during a 125 pb -1 exposure of the D0 detector to √s=1.8 TeV anti pp collisions. Six events consistent with the hypothesis t anti t → bW + , anti bW - → b anti lν, anti bl anti ν form the dilepton sample. The kinematics of such events may be reconstructed for any assumed mt, and the likelihood of each such solution evaluated. A measurement of m t based on these relative solution likelihoods gives m t = 169.9 ± 14.8 (stat.) ± 3. 8 (syst.) GeV/c 2 . A 2C kinematic fit is performed on a sample of 77 events consistent with t anti t → bW + , anti bW - → b anti lν, anti bq anti q , and this, in combination with an estimate on the likelihood that each event is top, yields m t = 173.3 ± 5.6 (stat.) ± 6.2 (syst.) GeV/c 2 . A combination of these two measurements gives m t = 173.1 ± 5.2 (stat.) ± 5.7 (syst.) GeV/c 2

  7. Spin-one top partner: phenomenology

    Science.gov (United States)

    Collins, Jack H.; Jain, Bithika; Perelstein, Maxim; Lorier, Nicolas Rey-Le

    2014-08-01

    Cai, Cheng, and Terning (CCT) suggested a model in which the left-handed top quark is identified with a gaugino of an extended gauge group, and its superpartner is a spin-1 particle. We perform a phenomenological analysis of this model, with a focus on the spin-1 top partner, which we dub the "swan". We find that precision electroweak fits, together with direct searches for Z ' bosons at the LHC, place a lower bound of at least about 4.5 TeV on the swan mass. An even stronger bound, 10 TeV or above, applies in most of the parameter space, mainly due to the fact that the swan is typically predicted to be significantly heavier than the Z '. We find that the 125 GeV Higgs can be easily accommodated in this model with non-decoupling D-terms. In spite of the strong lower bound on the swan mass, we find that corrections to Higgs couplings to photons and gluons induced by swan loops are potentially observable at future Higgs factories. We also briefly discuss the prospects for discovering a swan at the proposed 100 TeV pp collider.

  8. Top-tier requirements for KNGR

    International Nuclear Information System (INIS)

    Sung-Jae, Ch.; Kwangho, L.; Dong Wook, J.

    1996-01-01

    In 1992, Korea Electric Power Corporation (KEPCO) has launched the next generation reactor project to develop the standard design of an advanced pressurized water reactor by 2000. This advanced reactor aims to have the sufficient capability to be a safe, environmentally sound and economical energy source for 2000's in Korea. In conjunction with the project development, the program phase I is studied and it is in the Korean Next Generation Reactor (KNGR) first phase project that the requirements of this specification called ''Top-tier'' have been established. These functional requirements are of the first importance for the design, construction and operation of a nuclear power plant. These requirements are divided into safety requirements, serious accidents control, design base requirements, definition of the system characteristics, performance, construction feasibility, economical objectives, site parameters and design processes. The ''Top-tier'' requirements are concentrated on the improvement of the safety and reliability. Safety is one of the first priorities. In particular, the requirements for the design of the next reactors generation must include the capacity to control serious accidents because when an accident occurs, the protection degree is crucial. The KNGR requirements include the existing nuclear power plants competitiveness as well as those of the coal thermal plants. Moreover, when safety is reinforced, the economic competitiveness can be assured. At the present time, a subsequent specification for the KNGR considering the bases of the domestic technology and experimenting the running. (O.M.)

  9. On the Interpretation of Top Partners Searches

    CERN Document Server

    Matsedonskyi, Oleksii; Wulzer, Andrea

    2014-01-01

    Relatively light Top Partners are unmistakable signatures of reasonably Natural Composite Higgs models and as such they are worth searching for at the LHC. Their phenomenology is characterized by a certain amount of model-dependence, which makes the interpretation of Top Partner experimental searches not completely straightforward especially if one is willing to take also single production into account. We describe a model-independent strategy by which the interpretation is provided on the parameter space of a Simplified Model that captures the relevant features of all the explicit constructions. The Simplified Model limits are easy to interpret within explicit models, in a way that requires no recasting and no knowledge of the experimental details of the analyses. We illustrate the method by concrete examples, among which the searches for a charge 5/3 Partner in same-sign dileptons and the searches for a charge 2/3 singlet. In each case we perform a theory recasting of the available 8 TeV Run-1 results and a...

  10. Mechanical Engineering | Classification | College of Engineering & Applied

    Science.gov (United States)

    Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

  11. Biomedical Engineering | Classification | College of Engineering & Applied

    Science.gov (United States)

    Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

  12. Materials Science & Engineering | Classification | College of Engineering &

    Science.gov (United States)

    Biomedical Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

  13. Electrical Engineering | Classification | College of Engineering & Applied

    Science.gov (United States)

    Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

  14. Engineering tribology

    CERN Document Server

    Stachowiak, Gwidon; Batchelor, A W; Batchelor, Andrew W

    2005-01-01

    As with the previous edition, the third edition of Engineering Tribology provides a thorough understanding of friction and wear using technologies such as lubrication and special materials. Tribology is a complex topic with its own terminology and specialized concepts, yet is vitally important throughout all engineering disciplines, including mechanical design, aerodynamics, fluid dynamics and biomedical engineering. This edition includes updated material on the hydrodynamic aspects of tribology as well as new advances in the field of biotribology, with a focus throughout on the engineering ap

  15. All-solution processed organic solar cells with top illumination

    NARCIS (Netherlands)

    Patil, B.R.; Shanmugam, S.; Teunissen, J.P.; Galagan, Y.

    2015-01-01

    All-solution processed organic solar cells with inverted device architecture were demonstrated. Devices contain opaque bottom electrodes and semitransparent top electrodes, resulting in top illuminated devices. Nanoparticles-based Ag ink was used for inkjet printing both top and bottom electrodes.

  16. Solar central receiver reformer system for ammonia plants

    Science.gov (United States)

    1980-07-01

    Details of the conceptual design, economic analysis, and development plan for a solar central receiver system for retrofitting the Valley Nitrogen Producers, Inc., El Centro, California 600 ST/SD Ammonia Plant are presented. The retrofit system consists of a solar central receiver reformer (SCRR) operating in parallel with the existing fossil fired reformer. Steam and hydrocarbon react in the catalyst filled tubes of the inner cavity receiver to form a hydrogen rich mixture which is the syngas feed for the ammonia production. The SCRR system displaces natural gas presently used in the fossil reformer combustion chamber. The solar reformer retrofit system characteristics and its interface with the existing plant are simple, incorporating state of the art components with proven technology. A northfield composed of one thousand forty second generation heliostats provides solar energy to the receiver which is positioned on top of a 90 meter high steel tower. The overall economics of this system can provide over 20% discount cash flow rate of return with proper investment and market conditions.

  17. The top-ten in journal impact factor manipulation.

    Science.gov (United States)

    Falagas, Matthew E; Alexiou, Vangelis G

    2008-01-01

    A considerable part of the scientific community is, at least to some degree, involved in the "impact factor game". Editors strive to increase their journals' impact factor (IF) in order to gain influence in the fields of basic and applied research and scientists seek to profit from the "added value" of publishing in top IF journals. In this article we point out the most common "tricks" of engineering and manipulating the IF undertaken by a portion of professionals of the scientific publishing industry. They attempt to increase the nominator or decrease the denominator of the IF equation by taking advantage of certain design flaws and disadvantages of the IF that permit a degree of artificial and arbitrary inflation. Some of these practices, if not scientifically unethical, are at least questionable and should be abandoned. Editors and publishers should strive for quality through fair and thoughtful selection of papers forwarded for peer review and editorial comments that enhance the quality and scientific accuracy of a manuscript.

  18. Viral Marketing Determinants of Top Online Shop Brands in Indonesia

    Directory of Open Access Journals (Sweden)

    Aditya Wardhana

    2016-06-01

    Full Text Available The existence of the internet starts to shifting the purchase as a conventional to online. One of marketing strategies used by online store is viral marketing.The purpose of this study is to find determinant that forms viral marketing based on perceived customers in top brand online store such as lazada.com, olx.com, tokopedia.com, zalora.com, blibli.com, and bhinneka.com. The Research methodology used is the quantitative method with descriptive analysis using factor analysis by a population as 3.271.147 people and the number of sample uses Slovin formulas with confidency level at 95 % obtained as 400 respondents. Based on the result of research, there are twelve factors formed a new factor called viral marketing online store. Based on its priority, those dimensions of viral marketing online store can be sorted as follows: customer recommendation, newsletter, linking strategies, communities, free offer, sweepstakes, list of prospective buyers, chatrooms, reference list, product texts, affiliate programs, dan search engine.

  19. Engineering Documentation and Data Control

    Science.gov (United States)

    Matteson, Michael J.; Bramley, Craig; Ciaruffoli, Veronica

    2001-01-01

    Mississippi Space Services (MSS) the facility services contractor for NASA's John C. Stennis Space Center (SSC), is utilizing technology to improve engineering documentation and data control. Two identified improvement areas, labor intensive documentation research and outdated drafting standards, were targeted as top priority. MSS selected AutoManager(R) WorkFlow from Cyco software to manage engineering documentation. The software is currently installed on over 150 desctops. The outdated SSC drafting standard was written for pre-CADD drafting methods, in other words, board drafting. Implementation of COTS software solutions to manage engineering documentation and update the drafting standard resulted in significant increases in productivity by reducing the time spent searching for documents.

  20. Top 10% Admissions in the Borderlands: Access and Success of Borderland Top Students at Texas Public Universities

    Science.gov (United States)

    Rodríguez, Cristóbal

    2016-01-01

    This study focuses on Texas Borderland students admitted through the Texas Top 10% admissions policy, which assumes that Top 10% students are college ready for any public university and provides Top 10% high school graduates automatic admission to any 4-year public university in Texas. Using descriptive and inferential statistics, results…