MEGASTAR: The Meaning of Energy Growth: An Assessment of Systems, Technologies, and Requirements

Science.gov (United States)

1974-01-01

A methodology for the display and analysis of postulated energy futures for the United States is presented. A systems approach that includes the methodology of technology assessment is used to examine three energy scenarios--the Westinghouse Nuclear Electric Economy, the Ford Technical Fix Base Case and a MEGASTAR generated Alternate to the Ford Technical Fix Base Case. The three scenarios represent different paths of energy consumption for the present to the year 2000. Associated with these paths are various mixes of fuels, conversion, distribution, conservation and end-use technologies. MEGASTAR presents the estimated times and unit requirements to supply the fuels, conversion and distribution systems for the postulated end uses for the three scenarios and then estimates the aggregate manpower, materials, and capital requirements needed to develop the energy system described by the particular scenario. The total requirements and the energy subsystems for each scenario are assessed for their primary impacts in the areas of society, the environment, technology and the economy.

Characterization and assessment of novel bulk storage technologies : a study for the DOE Energy Storage Systems program.

Energy Technology Data Exchange (ETDEWEB)

Huff, Georgianne; Tong, Nellie (KEMA Consulting, Fairfax, VA); Fioravanti, Richard (KEMA Consulting, Fairfax, VA); Gordon, Paul (Sentech/SRA International, Bethesda, MD); Markel, Larry (Sentech/SRA International, Bethesda, MD); Agrawal, Poonum (Sentech/SRA International, Bethesda, MD); Nourai, Ali (KEMA Consulting, Fairfax, VA)

2011-04-01

This paper reports the results of a high-level study to assess the technological readiness and technical and economic feasibility of 17 novel bulk energy storage technologies. The novel technologies assessed were variations of either pumped storage hydropower (PSH) or compressed air energy storage (CAES). The report also identifies major technological gaps and barriers to the commercialization of each technology. Recommendations as to where future R&D efforts for the various technologies are also provided based on each technology's technological readiness and the expected time to commercialization (short, medium, or long term). The U.S. Department of Energy (DOE) commissioned this assessment of novel concepts in large-scale energy storage to aid in future program planning of its Energy Storage Program. The intent of the study is to determine if any new but still unproven bulk energy storage concepts merit government support to investigate their technical and economic feasibility or to speed their commercialization. The study focuses on compressed air energy storage (CAES) and pumped storage hydropower (PSH). It identifies relevant applications for bulk storage, defines the associated technical requirements, characterizes and assesses the feasibility of the proposed new concepts to address these requirements, identifies gaps and barriers, and recommends the type of government support and research and development (R&D) needed to accelerate the commercialization of these technologies.

Assessing systemwide occupational health and safety risks of energy technologies

International Nuclear Information System (INIS)

Rowe, M.D.

1982-01-01

Input-output modelling is now being used to assess systemwide occupational and public health and safety risks of energy technologies. Some of the advantages and disadvantages of this method are presented and some of its important limitations are discussed. Its primary advantage is that it provides a standard method with which to compare technologies on a consistent basis without extensive economic analysis. Among the disadvantages are limited range of applicability, limited spectrum of health impacts, and inability to identify unusual health impacts unique to a new technology. (author)

Cost, Time, and Risk Assessment of Different Wave Energy Converter Technology Development Trajectories: Preprint

Energy Technology Data Exchange (ETDEWEB)

Weber, Jochem W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Laird, Daniel [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Costello, Ronan [Wave Venture; Roberts, Jesse [Sandia National Laboratories; Bull, Diana [Sandia National Laboratories; Babarit, Aurelien [Ecole Centrale de Nantes; Nielsen, Kim [Ramboll; Ferreira, Claudio Bittencourt [DNV-GL; Kennedy, Ben [Wave Venture

2017-09-14

This paper presents a comparative assessment of three fundamentally different wave energy converter technology development trajectories. The three technology development trajectories are expressed and visualised as a function of technology readiness levels and technology performance levels. The assessment shows that development trajectories that initially prioritize technology readiness over technology performance are likely to require twice the development time, consume a threefold of the development cost, and are prone to a risk of technical or commercial failure of one order of magnitude higher than those development trajectories that initially prioritize technology performance over technology readiness.

Tiger Team Assessment of the Pittsburgh Energy Technology Center, [August 19--September 13, 1991

International Nuclear Information System (INIS)

1991-09-01

This report documents the results of the Department of Energy (DOE) Tiger Team Assessment conducted at Pittsburgh Energy Technology Center (PETC) near Pittsburgh, Pennsylvania, between August 19 and September 13, 1991. A team comprised of professionals from the Department, its contractors, and consultants conducted the assessment. The purpose of the assessment was to provide the Secretary of Energy the status of environment, safety, and health (ES ampersand H) programs at PETC. A management assessment was performed

Parameter variation and scenario analysis in impact assessments of emerging energy technologies

OpenAIRE

Breunig, Hanna Marie

2015-01-01

There is a global need for energy technologies that reduce the adverse impacts of societal progress and that address today's challenges without creating tomorrow's problems. Life cycle impact assessment (LCIA) can support technology developers in achieving these prerequisites of sustainability by providing a systems perspective. However, modeling the early-stage scale up and impacts of technology systems may lead to unreliable or incomplete results due to a lack of representative technical, s...

Technical and economic assessment of energy conversion technologies for MSW

Energy Technology Data Exchange (ETDEWEB)

Livingston, W.R.

2002-07-01

Thermal processes for municipal solid wastes (MSW) based on pyrolysis and/or gasification that have relevance to the emerging UK market are described in this report, and the results of the technical and economical assessment of these processes are presented. The Mitsui R21 Technology, the Thermoselect Process, the Nippon Steel Waste Melting Process, the Pyropleq Process, and the Compact Power Process are selected for detailed comparison on the basis of the overall technical concept, the energy balance and the requirements for consumables, environmental performance, and the technical and commercial status of the technology. Details are also given of a comparison of the novel thermal technologies with conventional mass burn incineration for MSW.

Technical and economic assessment of energy conversion technologies for MSW

International Nuclear Information System (INIS)

Livingston, W.R.

2002-01-01

Thermal processes for municipal solid wastes (MSW) based on pyrolysis and/or gasification that have relevance to the emerging UK market are described in this report, and the results of the technical and economical assessment of these processes are presented. The Mitsui R21 Technology, the Thermoselect Process, the Nippon Steel Waste Melting Process, the Pyropleq Process, and the Compact Power Process are selected for detailed comparison on the basis of the overall technical concept, the energy balance and the requirements for consumables, environmental performance, and the technical and commercial status of the technology. Details are also given of a comparison of the novel thermal technologies with conventional mass burn incineration for MSW

Assessment of Wave Energy in the South China Sea Based on GIS Technology

Directory of Open Access Journals (Sweden)

Gang Lin

2017-01-01

Full Text Available China is now the world’s largest user of coal and also has the highest greenhouse gas emissions associated with the mining and use of coal. Under today’s enormous pressures of the growing shortage of conventional energy sources and the need for emission reductions, the search for clean energy is the most effective strategy to address the energy crisis and global warming. This study utilized satellite remote sensing technology, geographic information system (GIS technology, and simulated wave data for the South China Sea. The characteristic features of the wave energy were obtained by analysis through the wave resource assessment formula and the results were stored in a GIS database. Software for the evaluation of wave energy in the South China Sea was written. The results should provide accurate, efficient references for wave energy researchers and decision-makers. Based on a 24-year WW3 model simulation wave data and GIS technology, this study presented the characteristic of the wave energy in the SCS; results demonstrated that the SCS has the feasibility and viability for wave energy farming.

Dynamic integrated assessment of bioenergy technologies for energy production utilizing agricultural residues: An input–output approach

International Nuclear Information System (INIS)

Song, Junnian; Yang, Wei; Higano, Yoshiro; Wang, Xian’en

2015-01-01

Highlights: • A dynamic input–output model is developed with bioenergy technologies complemented. • Availability of agricultural residues for bioenergy technologies is evaluated. • Trends in electricity and biofuel production are simulated dynamically. • Net profit and GHG mitigation contribution of bioenergy technologies are assessed. • Combustion power generation and briquette fuel are more advantageous. - Abstract: In order to facilitate regional agricultural residue utilization for energy production through bioenergy technologies, a dynamic input–output model is developed to estimate and assess the energy, economic and environmental performances of industrialization of five bioenergy technologies within a 15-year time horizon. Electricity and solid, gaseous and liquid biofuels are energy products of bioenergy technologies. Bioenergy technologies are complemented into regional input–output framework and combined with socioeconomic activities aided by their bottom-up economic and energy parameters. The simulation results for the target area indicate that the agricultural residues available for bioenergy technologies could amount to 55.16 million t, facilitating to 8.38 million t coal-equivalent bioenergy production by 2025. A 3.1% net reduction in accumulative greenhouse gas emission compared with the “business as usual” case could be achieved owing to substitution of fossil energy with electricity and biofuels produced by bioenergy technologies. From energy production, economic benefits and greenhouse gas mitigation three aspects integratedly, direct-combustion power generation and briquette fuel are more advantageous in the target area. The quantified energy, economic and environmental performances of bioenergy technologies are expected to give recommendations for their industrial development.

Water assessment for the Lower Colorado River region-emerging energy technology development

Science.gov (United States)

1981-08-01

Water supply availability for two hypothetical levels of emerging energy technology development are assessed. The water and related land resources implications of such hypothetical developments are evaluated. Water requirement, the effects on water quality, costs of water supplies, costs of disposal of wastewaters, and the environmental, economic and social impacts are determined, providing information for the development of non-nuclear energy research.

Superconducting magnetic energy storage (SMES). Results of a technology assessment

International Nuclear Information System (INIS)

Fleischer, T.; Juengst, K.P.; Brandl, V.; Maurer, W.; Nieke, E.

1995-05-01

The authors report on results of a Technology Assessment study commissioned by the German Federal Ministry of Education, Science, Research and Technology. The objective of this study was to evaluate the potential of superconducting magnetic energy storage (SMES) technology with respect to the economical, political and organization structures in the Federal Republic of Germany. The main focus of the study was on the technical and economic potential of large-scale SMES for diurnal load levelling applications. It was shown that there is no demand for the development of large SMES in Germany in the short and medium term. A second range of applications investigated is storage of electric energy for immediate delivery or consumption of electric power in case of need or for periodic power supply within the range of seconds. Due to its excellent dynamic properties SMES has substantial advantages over conventional storage technologies in this field. For those so-called dynamic applications SMES of small and medium energy capacity are needed. It was shown that SMES may be economically attractive for the provision of spinning reserve capacity in electrical networks, in particular cases for power quality applications (uninterruptable power supply, UPS) and for the compensation of cyclic loads, as well as in some market niches. The use of SMES for storage of recuperated energy in electrical railway traction systems has been proven to be uneconomical. Mobile SMES applications are unrealistic due to technical and size limitations. In SMES systems the energy is stored in a magnetic field. Biological objects as well as technical systems in the vicinity of a SMES plant are exposed to this field. The knowledge on impacts of magnetic fields on sensitive technical systems as well as on living organisms and especially on effects on human health is rather small and quite uncertain. (orig./MM) [de

Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Cement Sector

Energy Technology Data Exchange (ETDEWEB)

Sathaye, J.; Xu, T.; Galitsky, C.

2010-08-15

Adoption of efficient end-use technologies is one of the key measures for reducing greenhouse gas (GHG) emissions. How to effectively analyze and manage the costs associated with GHG reductions becomes extremely important for the industry and policy makers around the world. Energy-climate (EC) models are often used for analyzing the costs of reducing GHG emissions for various emission-reduction measures, because an accurate estimation of these costs is critical for identifying and choosing optimal emission reduction measures, and for developing related policy options to accelerate market adoption and technology implementation. However, accuracies of assessing of GHG-emission reduction costs by taking into account the adoption of energy efficiency technologies will depend on how well these end-use technologies are represented in integrated assessment models (IAM) and other energy-climate models.

Emerging energy-efficient industrial technologies

Energy Technology Data Exchange (ETDEWEB)

Martin, N.; Worrell, E.; Ruth, M.; Price, L.; Elliott, R.N.; Shipley, A.M.; Thorne, J.

2000-10-01

U.S. industry consumes approximately 37 percent of the nation's energy to produce 24 percent of the nation's GDP. Increasingly, industry is confronted with the challenge of moving toward a cleaner, more sustainable path of production and consumption, while increasing global competitiveness. Technology will be essential for meeting these challenges. At some point, businesses are faced with investment in new capital stock. At this decision point, new and emerging technologies compete for capital investment alongside more established or mature technologies. Understanding the dynamics of the decision-making process is important to perceive what drives technology change and the overall effect on industrial energy use. The assessment of emerging energy-efficient industrial technologies can be useful for: (1) identifying R&D projects; (2) identifying potential technologies for market transformation activities; (3) providing common information on technologies to a broad audience of policy-makers; and (4) offering new insights into technology development and energy efficiency potentials. With the support of PG&E Co., NYSERDA, DOE, EPA, NEEA, and the Iowa Energy Center, staff from LBNL and ACEEE produced this assessment of emerging energy-efficient industrial technologies. The goal was to collect information on a broad array of potentially significant emerging energy-efficient industrial technologies and carefully characterize a sub-group of approximately 50 key technologies. Our use of the term ''emerging'' denotes technologies that are both pre-commercial but near commercialization, and technologies that have already entered the market but have less than 5 percent of current market share. We also have chosen technologies that are energy-efficient (i.e., use less energy than existing technologies and practices to produce the same product), and may have additional ''non-energy benefits.'' These benefits are as important (if

Assessing Rare Metal Availability Challenges for Solar Energy Technologies

Directory of Open Access Journals (Sweden)

Leena Grandell

2015-08-01

Full Text Available Solar energy is commonly seen as a future energy source with significant potential. Ruthenium, gallium, indium and several other rare elements are common and vital components of many solar energy technologies, including dye-sensitized solar cells, CIGS cells and various artificial photosynthesis approaches. This study surveys solar energy technologies and their reliance on rare metals such as indium, gallium, and ruthenium. Several of these rare materials do not occur as primary ores, and are found as byproducts associated with primary base metal ores. This will have an impact on future production trends and the availability for various applications. In addition, the geological reserves of many vital metals are scarce and severely limit the potential of certain solar energy technologies. It is the conclusion of this study that certain solar energy concepts are unrealistic in terms of achieving TW scales.

Critical Metals in Strategic Energy Technologies. Assessing Rare Metals as Supply-Chain Bottlenecks in Low-Carbon Energy Technologies

International Nuclear Information System (INIS)

Moss, R.L.; Tzimas, E.; Kara, H.; Willis, P.; Kooroshy, J.

2011-11-01

Due to the rapid growth in demand for certain materials, compounded by political risks associated with the geographical concentration of the supply of them, a shortage of these materials could be a potential bottleneck to the deployment of low-carbon energy technologies. In order to assess whether such shortages could jeopardise the objectives of the EU's Strategic Energy Technology Plan (SET-Plan), an improved understanding of these risks is vital. In particular, this report examines the use of metals in the six low-carbon energy technologies of SET-Plan, namely: nuclear, solar, wind, bioenergy, carbon capture and storage (CCS) and electricity grids. The study looks at the average annual demand for each metal for the deployment of the technologies in Europe between 2020 and 2030. The demand of each metal is compared to the respective global production volume in 2010. This ratio (expressed as a percentage) allows comparing the relative stress that the deployment of the six technologies in Europe is expected to create on the global supplies for these different metals. The study identifies 14 metals for which the deployment of the six technologies will require 1% or more (and in some cases, much more) of current world supply per annum between 2020 and 2030. These 14 metals, in order of decreasing demand, are tellurium, indium, tin, hafnium, silver, dysprosium, gallium, neodymium, cadmium, nickel, molybdenum, vanadium, niobium and selenium. The metals are examined further in terms of the risks of meeting the anticipated demand by analysing in detail the likelihood of rapid future global demand growth, limitations to expanding supply in the short to medium term, and the concentration of supply and political risks associated with key suppliers. The report pinpoints 5 of the 14 metals to be at high risk, namely: the rare earth metals neodymium and dysprosium, and the by-products (from the processing of other metals) indium, tellurium and gallium. The report explores a

Advanced energy technologies and climate change: An analysis using the Global Change Assessment Model (GCAM)

International Nuclear Information System (INIS)

Edmonds, J.; Wise, M.; MacCracken, C.

1994-01-01

The authors report results from a ''top down'' energy-economy model employing ''bottom up'' assumptions and embedded in an integrated assessment framework, GCAM. The analysis shows that, from the perspective of long-term energy system development, differences in results from the ''top down'' and ''bottom up'' research communities would appear to be more closely linked to differences in assumptions regarding the economic cost associated with advanced technologies than to differences in modeling approach. The adoption of assumptions regarding advanced energy technologies were shown to have a profound effect on the future rate of anthropogenic climate change. The cumulative effect of the five sets of advanced energy technologies is to reduce annual emissions from fossil fuel use to levels which stabilize atmospheric concentrations below 550 ppmv, the point at which atmospheric concentrations are double those that existed in the middle of the eighteenth century. The consideration of all greenhouse gases, and in particular sulfur, leads to some extremely interesting results that the rapid deployment of advanced energy technologies leads to higher temperatures prior to 2050 than in the reference case. This is due to the fact that the advanced energy technologies reduce sulfur emissions as well as those of carbon. The short-term cooling impact of sulfur dominates the long-term warming impact of CO 2 and CH 4 . While all energy technologies play roles, the introduction of advanced biomass energy production technology plays a particularly important role. 16 refs., 12 figs., 3 tabs

Inter-technology knowledge spillovers for energy technologies

International Nuclear Information System (INIS)

Nemet, Gregory F.

2012-01-01

Both anecdotal evidence and the innovation literature indicate that important advances in energy technology have made use of knowledge originating in other technological areas. This study uses the set of U.S. patents granted from 1976 to 2006 to assess the role of knowledge acquired from outside each energy patent's technological classification. It identifies the effect of external knowledge on the forward citation frequency of energy patents. The results support the claim above. Regression coefficients on citations to external prior art are positive and significant. Further, the effect of external citations is significantly larger than that of other types of citations. Conversely, citations to prior art that is technologically near have a negative effect on forward citation frequency. These results are robust across several alternative specifications and definitions of whether each flow of knowledge is external. Important energy patents have drawn heavily from external prior art categorized as chemical, electronics, and electrical; they cite very little prior art from computers, communications, and medical inventions.

Assessment of Vehicle Sizing, Energy Consumption and Cost Through Large Scale Simulation of Advanced Vehicle Technologies

Energy Technology Data Exchange (ETDEWEB)

Moawad, Ayman [Argonne National Lab. (ANL), Argonne, IL (United States); Kim, Namdoo [Argonne National Lab. (ANL), Argonne, IL (United States); Shidore, Neeraj [Argonne National Lab. (ANL), Argonne, IL (United States); Rousseau, Aymeric [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-01-01

The U.S. Department of Energy (DOE) Vehicle Technologies Office (VTO) has been developing more energy-efficient and environmentally friendly highway transportation technologies that will enable America to use less petroleum. The long-term aim is to develop "leapfrog" technologies that will provide Americans with greater freedom of mobility and energy security, while lowering costs and reducing impacts on the environment. This report reviews the results of the DOE VTO. It gives an assessment of the fuel and light-duty vehicle technologies that are most likely to be established, developed, and eventually commercialized during the next 30 years (up to 2045). Because of the rapid evolution of component technologies, this study is performed every two years to continuously update the results based on the latest state-of-the-art technologies.

Full report: Assessment and opportunity identification of energy efficient pollution prevention technologies and processes

Energy Technology Data Exchange (ETDEWEB)

1994-11-01

US industry produces about 12 billion tons of waste a year, or two-thirds of the waste generated in the US. The costs of handling and disposing of these wastes are significant, estimated to be between $25 and $43 billion in 1991, and represent an increase of 66% since 1986. US industry also uses about one-third of all energy consumed in the nation, which adds to the environmental burden. Industrial wastes affect the environmental well-being of the nation and, because of their growing costs, the competitive abilities of US industry. As part of a national effort to reduce industrial wastes, the US Congress passed the Energy Policy Act (EPAct, P.L. 102-486). Section 2108, subsections (b) and (c), of EPAct requires the Department of Energy (DOE) to identify opportunities to demonstrate energy efficient pollution prevention technologies and processes; to assess their availability and the energy, environmental, and cost effects of such technologies; and to report the results. Work for this report clearly pointed to two things, that there is insufficient data on wastes and that there is great breadth and diversity in the US industrial sector. This report identifies: information currently available on industrial sector waste streams, opportunities for demonstration of energy efficient pollution prevention technologies in two industries that produce significant amounts of waste--chemicals and petroleum, characteristics of waste reducing and energy saving technologies identifiable in the public literature, and potential barriers to adoption of waste reducing technologies by industry.

Technology assessment of thermal treatment technologies using ORWARE

International Nuclear Information System (INIS)

Assefa, G.; Eriksson, O.; Frostell, B.

2005-01-01

A technology assessment of thermal treatment technologies for wastes was performed in the form of scenarios of chains of technologies. The Swedish assessment tool, ORWARE, was used for the assessment. The scenarios of chains of thermal technologies assessed were gasification with catalytic combustion, gasification with flame combustion, incineration and landfilling. The landfilling scenario was used as a reference for comparison. The technologies were assessed from ecological and economic points of view. The results are presented in terms of global warming potential, acidification potential, eutrophication potential, consumption of primary energy carriers and welfare costs. From the simulations, gasification followed by catalytic combustion with energy recovery in a combined cycle appeared to be the most competitive technology from an ecological point of view. On the other hand, this alternative was more expensive than incineration. A sensitivity analysis was done regarding electricity prices to show which technology wins at what value of the unit price of electricity (SEK/kW h). Within this study, it was possible to make a comparison both between a combined cycle and a Rankine cycle (a system pair) and at the same time between flame combustion and catalytic combustion (a technology pair). To use gasification just as a treatment technology is not more appealing than incineration, but the possibility of combining gasification with a combined cycle is attractive in terms of electricity production. This research was done in connection with an empirical R and D work on both gasification of waste and catalytic combustion of the gasified waste at the Division of Chemical Technology, Royal Institute of Technology (KTH), Sweden

Policies for the Energy Technology Innovation System (ETIS)

NARCIS (Netherlands)

Grubler, A.; Aguayo, F.; Gallagher, K.; Hekkert, M.P.; Jiang, K.; Mytelka, L.; Neij, L.; Nemet, G.; Wilson, C.

2012-01-01

Innovation and technological change are integral to the energy system transformations described in the Global Energy Assessment (GEA) pathways. Energy technology innovations range from incremental improvements to radical breakthroughs and from technologies and infrastructure to social institutions

Risk assessment research and technology assessment

International Nuclear Information System (INIS)

Albach, H.; Schade, D.; Sinn, H.

1991-01-01

The concepts and approaches for technology assessment, the targets and scientific principles, as well as recognizable deficits and recommendations concerning purposeful strategies for the promotion of this research field require a dialog between those concerned. Conception, deficits, and the necessary measures for risk assessment research and technology assessment were discussed as well as ethical aspects. The problematic nature of using organisms altered through genetic engineering in the open land, traffic and transport, site restoration, nuclear energy, and isotope applications were subjects particularly dealt with. (DG) [de

Technology data for energy plants. Individual heating plants and energy transport

Energy Technology Data Exchange (ETDEWEB)

2012-05-15

The present technology catalogue is published in co-operation between the Danish Energy Agency and Energinet.dk and includes technology descriptions for a number of technologies for individual heat production and energy transport. The primary objective of the technology catalogue is to establish a uniform, commonly accepted and up-to-date basis for the work with energy planning and the development of the energy sector, including future outlooks, scenario analyses and technical/economic analyses. The technology catalogue is thus a valuable tool in connection with energy planning and assessment of climate projects and for evaluating the development opportunities for the energy sector's many technologies, which can be used for the preparation of different support programmes for energy research and development. The publication of the technology catalogue should also be viewed in the light of renewed focus on strategic energy planning in municipalities etc. In that respect, the technology catalogue is considered to be an important tool for the municipalities in their planning efforts. (LN)

Department of Energy Small-Scale Hydropower Program: Feasibility assessment and technology development summary report

International Nuclear Information System (INIS)

Rinehart, B.N.

1991-06-01

This report summarizes two subprograms under the US Department of Energy's Small-Scale Hydroelectric Power Program. These subprograms were part of the financial assistance activities and included the Program Research and Development Announcement (PRDA) feasibility assessments and the technology development projects. The other major subprograms included engineering research and development, legal and institutional aspects, and technology transfer. These other subprograms are covered in their respective summary reports. The problems of energy availability and increasing costs of energy led to a national effort to develop economical and environmental attractive alternative energy resources. One such alternative involved the utilization of existing dams with hydraulic heads of <65 ft and the capacity to generate hydroelectric power of 15 MW or less. Thus, the PRDA program was initiated along with the Technology Development program. The purpose of the PRDA feasibility studies was to encourage development of renewable hydroelectric resources by providing engineering, economic, environmental, safety, and institutional information. Fifty-five feasibility studies were completed under the PRDA. This report briefly summarizes each of those projects. Many of the PRDA projects went on to become technology development projects. 56 refs., 1 fig., 2 tabs

Department of Energy Small-Scale Hydropower Program: Feasibility assessment and technology development summary report

Energy Technology Data Exchange (ETDEWEB)

Rinehart, B.N.

1991-06-01

This report summarizes two subprograms under the US Department of Energy's Small-Scale Hydroelectric Power Program. These subprograms were part of the financial assistance activities and included the Program Research and Development Announcement (PRDA) feasibility assessments and the technology development projects. The other major subprograms included engineering research and development, legal and institutional aspects, and technology transfer. These other subprograms are covered in their respective summary reports. The problems of energy availability and increasing costs of energy led to a national effort to develop economical and environmental attractive alternative energy resources. One such alternative involved the utilization of existing dams with hydraulic heads of <65 ft and the capacity to generate hydroelectric power of 15 MW or less. Thus, the PRDA program was initiated along with the Technology Development program. The purpose of the PRDA feasibility studies was to encourage development of renewable hydroelectric resources by providing engineering, economic, environmental, safety, and institutional information. Fifty-five feasibility studies were completed under the PRDA. This report briefly summarizes each of those projects. Many of the PRDA projects went on to become technology development projects. 56 refs., 1 fig., 2 tabs.

An assessment of research and development leadership in ocean energy technologies

International Nuclear Information System (INIS)

Bruch, V.L.

1994-04-01

Japan is clearly the leader in ocean energy technologies. The United Kingdom also has had many ocean energy research projects, but unlike Japan, most of the British projects have not progressed from the feasibility study stage to the demonstration stage. Federally funded ocean energy research in the US was stopped because it was perceived the technologies could not compete with conventional sources of fuel. Despite the probable small market for ocean energy technologies, the short sighted viewpoint of the US government regarding funding of these technologies may be harmful to US economic competitiveness. The technologies may have important uses in other applications, such as offshore construction and oil and gas drilling. Discontinuing the research and development of these technologies may cause the US to lose knowledge and miss market opportunities. If the US wishes to maintain its knowledge base and a market presence for ocean energy technologies, it may wish to consider entering into a cooperative agreement with Japan and/or the United Kingdom. Cooperative agreements are beneficial not only for technology transfer but also for cost-sharing

Information Technology Resources Assessment

Energy Technology Data Exchange (ETDEWEB)

1993-04-01

The Information Technology Resources Assessment (ITRA) is being published as a companion document to the Department of Energy (DOE) FY 1994--FY 1998 Information Resources Management Long-Range Plan. This document represents a collaborative effort between the Office of Information Resources Management and the Office of Energy Research that was undertaken to achieve, in part, the Technology Strategic Objective of IRM Vision 21. An integral part of this objective, technology forecasting provides an understanding of the information technology horizon and presents a perspective and focus on technologies of particular interest to DOE program activities. Specifically, this document provides site planners with an overview of the status and use of new information technology for their planning consideration.

Energy conservation potential of surface modification technologies

Energy Technology Data Exchange (ETDEWEB)

Le, H.K.; Horne, D.M.; Silberglitt, R.S.

1985-09-01

This report assesses the energy conservation impact of surface modification technologies on the metalworking industries. The energy conservation impact of surface modification technologies on the metalworking industries is assessed by estimating their friction and wear tribological sinks and the subsequent reduction in these sinks when surface modified tools are used. Ion implantation, coatings, and laser and electron beam surface modifications are considered.

Selected bibliography: cost and energy savings of conservation and renewable energy technologies

Energy Technology Data Exchange (ETDEWEB)

None

1980-05-01

This bibliography is a compilation of reports on the cost and energy savings of conservation and renewable energy applications throughout the United States. It is part of an overall effort to inform utilities of technological developments in conservation and renewable energy technologies and so aid utilities in their planning process to determine the most effective and economic combination of capital investments to meet customer needs. Department of Energy assessments of the applications, current costs and cost goals for the various technologies included in this bibliography are presented. These assessments are based on analyses performed by or for the respective DOE Program Offices. The results are sensitive to a number of variables and assumptions; however, the estimates presented are considered representative. These assessments are presented, followed by some conclusions regarding the potential role of the conservation and renewable energy alternative. The approach used to classify the bibliographic citations and abstracts is outlined.

An assessment of thermal destruction technologies for application to Department of Energy mixed wastes

International Nuclear Information System (INIS)

1991-08-01

A study of known operational and emerging thermal treatment technologies was conducted for the Department of Energy's (DOE's) Office of Technology Development (OTD) through the Hazardous Waste Remedial Actions Program (HAZWRAP). This study addressed thermal treatment of mixed wastes (MWs), for which the most comprehensive set of waste has been divided into two volumes. Volume 1 contains the details and results of the technology assessments and comparisons between technologies. This volume (Volume 2) contains the comprehensive data collected on each technology, including descriptions, process and cost data, comments on advantages and deficiencies, types of waste treatable and by-products of these wastes, and reference information. 2 figs

Energy technology impacts on agriculture with a bibliography of models for impact assessment on crop ecosystems

Energy Technology Data Exchange (ETDEWEB)

Rupp, E.M.; Luxmoore, R.J.; Parzyck, D.C.

1979-09-01

Possible impacts of energy technologies on agriculture are evaluated, and some of the available simulation models that can be used for predictive purposes are identified. An overview of energy technologies and impacts on the environment is presented to provide a framework for the commentary on the models. Coal combustion is shown to have major impacts on the environment and these will continue into the next century according to current Department of Energy projections. Air pollution effects will thus remain as the major impacts on crop ecosystems. Two hundred reports were evaluated, representing a wide range of models increasing in complexity from mathematical functions (fitted to data) through parametric models (which represent phenomena without describing the mechanisms) to mechanistic models (based on physical, chemical, and physiological principles). Many models were viewed as suitable for adaptation to technology assessment through the incorporation of representative dose-response relationships. It is clear that in many cases available models cannot be taken and directly applied in technology assessment. Very few models of air pollutant-crop interactions were identified, even though there is a considerable data base of pollutant effects on crops.

Enabling technologies for industrial energy demand management

International Nuclear Information System (INIS)

Dyer, Caroline H.; Hammond, Geoffrey P.; Jones, Craig I.; McKenna, Russell C.

2008-01-01

This state-of-science review sets out to provide an indicative assessment of enabling technologies for reducing UK industrial energy demand and carbon emissions to 2050. In the short term, i.e. the period that will rely on current or existing technologies, the road map and priorities are clear. A variety of available technologies will lead to energy demand reduction in industrial processes, boiler operation, compressed air usage, electric motor efficiency, heating and lighting, and ancillary uses such as transport. The prospects for the commercial exploitation of innovative technologies by the middle of the 21st century are more speculative. Emphasis is therefore placed on the range of technology assessment methods that are likely to provide policy makers with a guide to progress in the development of high-temperature processes, improved materials, process integration and intensification, and improved industrial process control and monitoring. Key among the appraisal methods applicable to the energy sector is thermodynamic analysis, making use of energy, exergy and 'exergoeconomic' techniques. Technical and economic barriers will limit the improvement potential to perhaps a 30% cut in industrial energy use, which would make a significant contribution to reducing energy demand and carbon emissions in UK industry. Non-technological drivers for, and barriers to, the take-up of innovative, low-carbon energy technologies for industry are also outlined

Outlook for renewable energy technologies: Assessment of international programs and policies

Energy Technology Data Exchange (ETDEWEB)

Branstetter, L.J.; Vidal, R.C.; Bruch, V.L.; Zurn, R.

1995-02-01

The report presents an evaluation of worldwide research efforts in three specific renewable energy technologies, with a view towards future United States (US) energy security, environmental factors, and industrial competitiveness. The overall energy technology priorities of foreign governments and industry leaders, as well as the motivating factors for these priorities, are identified and evaluated from both technological and policy perspectives. The specific technologies of interest are wind, solar thermal, and solar photovoltaics (PV). These program areas, as well as the overall energy policies of Denmark, France, Germany, Italy, the United Kingdom (UK), Japan, Russia, and the European Community as a whole are described. The present and likely future picture for worldwide technological leadership in these technologies-is portrayed. The report is meant to help in forecasting challenges to US preeminence in the various technology areas, particularly over the next ten years, and to help guide US policy-makers as they try to identify specific actions which would help to retain and/or expand the US leadership position.

Principles of sustainability science to assess alternative energy technologies

CSIR Research Space (South Africa)

Brent, AC

2009-04-01

Full Text Available , adaptive capacity, and complexity of social-ecological systems to assess the potential of such technologies for increasing the carrying capacity and improving the resilience of social-ecological systems, or to assess the resilience of the technological...

Scenario comparisons of gasification technology using energy life cycle assessment for bioenergy recovery from rice straw in Taiwan

International Nuclear Information System (INIS)

Shie, J.L.; Lee, C.H.; Chen, C.S.; Lin, K.L.; Chang, C.Y.

2014-01-01

Highlights: • The energy balances of potential gasification technology and limitation boundary are evaluated. • The transportation and pre-treatment are the greatest parts of energy use. • Every technology process has positive energy benefits at all on-site pre-treatment cases. • The optimal ranges of transportation distance and treatment capacity are suggested. • The optimal technology from the tendency model is addressed. - Abstract: This study uses different scenarios to evaluate, by means of energy life-cycle assessments (ELCAs), the energy balance of potential gasification technology and limitation boundaries in Taiwan. Rice straw is chosen as the target material in this study because it is the most significant agriculture waste in Taiwan. Energy products include syngas (CO + H 2 ), methane, carbon dioxide and carbon black residue. The scenarios simulate capacities of 50,000–200,000 tons/year. The distances of collection and transportation are calculated by a circular area 50–100 km in diameter. Also, the on-site and off-site pretreatments of rice straw are evaluated. For this optimum scenario case, the average of the total input energy for the assessed systems is about 15.9% of the average output energy; the value of the net energy balance (NEB) is 0.841. Every technological process has positive energy benefits at all on-site scenario cases. As the capacity is increased, the energy consumption required for transportation increases and the values of the energy indicators decrease. According to the limitation boundaries from the tendency model at on-site cases, the suggested transportation distance and treatment capacity are below 114.72 km and 251,533 tons/year, respectively, while the energy return on investment (EROI) value is greater than 1

Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the U.S. Pulp and Paper Sector

Energy Technology Data Exchange (ETDEWEB)

Xu, Tengfang [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sathaye, Jayant [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Kramer, Klaas Jan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-07-01

Adoption of efficient end-use technologies is one of the key measures for reducing greenhouse gas (GHG) emissions. How to effectively analyze and manage the costs associated with GHG reductions becomes extremely important for the industry and policy makers around the world. Energy-climate (EC) models are often used for analyzing the costs of reducing GHG emissions for various emission-reduction measures, because an accurate estimation of these costs is critical for identifying and choosing optimal emission reduction measures, and for developing related policy options to accelerate market adoption and technology implementation. However, accuracies of assessing GHG-emission reduction costs by taking into account the adoption of energy efficiency technologies will depend on how well these end-use technologies are represented in integrated assessment models (IAM) and other energy-climate models. In this report, we first conduct a brief review of different representations of end-use technologies (mitigation measures) in various energy-climate models, followed by the problem statement, and a description of the basic concepts of quantifying the cost of conserved energy including integrating no-regrets options.

Battery energy storage systems: Assessment for small-scale renewable energy integration

Energy Technology Data Exchange (ETDEWEB)

Nair, Nirmal-Kumar C.; Garimella, Niraj [Power Systems Group, Department of Electrical and Computer Engineering, The University of Auckland, 38 Princes Street, Science Centre, Auckland 1142 (New Zealand)

2010-11-15

Concerns arising due to the variability and intermittency of renewable energy sources while integrating with the power grid can be mitigated to an extent by incorporating a storage element within the renewable energy harnessing system. Thus, battery energy storage systems (BESS) are likely to have a significant impact in the small-scale integration of renewable energy sources into commercial building and residential dwelling. These storage technologies not only enable improvements in consumption levels from renewable energy sources but also provide a range of technical and monetary benefits. This paper provides a modelling framework to be able to quantify the associated benefits of renewable resource integration followed by an overview of various small-scale energy storage technologies. A simple, practical and comprehensive assessment of battery energy storage technologies for small-scale renewable applications based on their technical merit and economic feasibility is presented. Software such as Simulink and HOMER provides the platforms for technical and economic assessments of the battery technologies respectively. (author)

PROMETHEE-ROC Model for Assessing the Readiness of Technology for Generating Energy

Directory of Open Access Journals (Sweden)

Danielle Costa Morais

2015-01-01

Full Text Available This paper puts forward a proposal for a multicriteria decision model for prioritizing technologies that are critical for power generation in the energy sector. It deals with the context of imprecise information regarding importance of criteria; then an integration of surrogate weights with the PROMETHEE method is undertaken in order to approach this context. In this type of strategic decision problem, how to deal with imprecise information is always a challenge. The use of surrogate weights presents a significant contribution and it can facilitate the assignment of weights in a decision ranking problem, which requires the decision-maker (DM to order the criteria by their importance for the decision problem. Thus for this situation of assessing the readiness of technology for generating energy where the DM is able and feels comfortable to order all criteria by their relative importance, the proposed approach of surrogate weights in the PROMETHEE II method, the PROMETHEE-ROC model, is shown to be an adequate approach.

Technology assessment of geothermal energy resource development

Energy Technology Data Exchange (ETDEWEB)

1975-04-15

Geothermal state-of-the-art is described including geothermal resources, technology, and institutional, legal, and environmental considerations. The way geothermal energy may evolve in the United States is described; a series of plausible scenarios and the factors and policies which control the rate of growth of the resource are presented. The potential primary and higher order impacts of geothermal energy are explored, including effects on the economy and society, cities and dwellings, environmental, and on institutions affected by it. Numerical and methodological detail is included in appendices. (MHR)

Framework for energy policy and technology assessment in developing countries: a case study of Peru

Energy Technology Data Exchange (ETDEWEB)

Mubayi, V.; Palmedo, P.F.; Doernberg, A.B.

1979-12-01

The potential of various energy sources and technology options in meeting national economic and social development goals in developing countries is assessed. The resource options that are of interest are the development of indigenous resources. In general, two categories of options can be considered: those which correspond to the accelerated implementation of existing elements of the energy system and those which correspond to the introduction of a new technology, such as solar electricity. The various resource and technology options that must be analyzed with respect to a number of criteria or payoff functions are: total demand and fuel mix; reduction of oil consumption; national social goals; total energy costs; and environmental quality. First, a view is constructed of the energy implications of current national economic development plans. A consistent description of the future energy system of the country, under the assumption of current trends and policies is constructed for certain reference years in the future. The values of the payoff functions selected are then calculated for that reference case. The major resource and technology options are identified and the rates at which they can be implemented are determined. Finally, the impact on the various payoff functions of the implementation of each option is calculated. The basic element of the framework is the Reference Energy System, discussed in Secton 3. The energy policy analysis for Peru is used as a reference case. 11 references, 10 figures, 2 tables.

Characterizing emerging industrial technologies in energy models

Energy Technology Data Exchange (ETDEWEB)

Laitner, John A. (Skip); Worrell, Ernst; Galitsky, Christina; Hanson, Donald A.

2003-07-29

Conservation supply curves are a common tool in economic analysis. As such, they provide an important opportunity to include a non-linear representation of technology and technological change in economy-wide models. Because supply curves are closely related to production isoquants, we explore the possibility of using bottom-up technology assessments to inform top-down representations of energy models of the U.S. economy. Based on a recent report by LBNL and ACEEE on emerging industrial technologies within the United States, we have constructed a supply curve for 54 such technologies for the year 2015. Each of the selected technologies has been assessed with respect to energy efficiency characteristics, likely energy savings by 2015, economics, and environmental performance, as well as needs for further development or implementation of the technology. The technical potential for primary energy savings of the 54 identified technologies is equal to 3.54 Quads, or 8.4 percent of the assume d2015 industrial energy consumption. Based on the supply curve, assuming a discount rate of 15 percent and 2015 prices as forecasted in the Annual Energy Outlook2002, we estimate the economic potential to be 2.66 Quads - or 6.3 percent of the assumed forecast consumption for 2015. In addition, we further estimate how much these industrial technologies might contribute to standard reference case projections, and how much additional energy savings might be available assuming a different mix of policies and incentives. Finally, we review the prospects for integrating the findings of this and similar studies into standard economic models. Although further work needs to be completed to provide the necessary link between supply curves and production isoquants, it is hoped that this link will be a useful starting point for discussion with developers of energy-economic models.

Emerging energy-efficient technologies for industry

International Nuclear Information System (INIS)

Worrell, Ernst; Martin, Nathan; Price, Lynn; Ruth, Michael; Elliott, Neal; Shipley, Anna; Thorn, Jennifer

2001-01-01

For this study, we identified about 175 emerging energy-efficient technologies in industry, of which we characterized 54 in detail. While many profiles of individual emerging technologies are available, few reports have attempted to impose a standardized approach to the evaluation of the technologies. This study provides a way to review technologies in an independent manner, based on information on energy savings, economic, non-energy benefits, major market barriers, likelihood of success, and suggested next steps to accelerate deployment of each of the analyzed technologies. There are many interesting lessons to be learned from further investigation of technologies identified in our preliminary screening analysis. The detailed assessments of the 54 technologies are useful to evaluate claims made by developers, as well as to evaluate market potentials for the United States or specific regions. In this report we show that many new technologies are ready to enter the market place, or are currently under development, demonstrating that the United States is not running out of technologies to improve energy efficiency and economic and environmental performance, and will not run out in the future. The study shows that many of the technologies have important non-energy benefits, ranging from reduced environmental impact to improved productivity. Several technologies have reduced capital costs compared to the current technology used by those industries. Non-energy benefits such as these are frequently a motivating factor in bringing technologies such as these to market. Further evaluation of the profiled technologies is still needed. In particular, further quantifying the non-energy benefits based on the experience from technology users in the field is important. Interactive effects and inter-technology competition have not been accounted for and ideally should be included in any type of integrated technology scenario, for it may help to better evaluate market

Assessment of Energy Impact of Window Technologies for Commercial Buildings

Energy Technology Data Exchange (ETDEWEB)

Hong, Tianzhen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Selkowitz, Stephen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Yazdanian, Mehry [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

2009-10-01

Windows play a significant role in commercial buildings targeting the goal of net zero energy. This report summarizes research methodology and findings in evaluating the energy impact of windows technologies for commercial buildings. The large office prototypical building, chosen from the DOE commercial building benchmarks, was used as the baseline model which met the prescriptive requirements of ASHRAE Standard 90.1-2004. The building simulations were performed with EnergyPlus and TMY3 weather data for five typical US climates to calculate the energy savings potentials of six windows technologies when compared with the ASHRAE 90.1-2004 baseline windows. The six windows cover existing, new, and emerging technologies, including ASHRAE 189.1 baseline windows, triple pane low-e windows, clear and tinted double pane highly insulating low-e windows, electrochromic (EC) windows, and highly insulating EC windows representing the hypothetically feasible optimum windows. The existing stocks based on average commercial windows sales are included in the analysis for benchmarking purposes.

AN ASSESSMENT OF FLYWHEEL HIGH POWER ENERGY STORAGE TECHNOLOGY FOR HYBRID VEHICLES

Energy Technology Data Exchange (ETDEWEB)

Hansen, James Gerald [ORNL

2012-02-01

An assessment has been conducted for the DOE Vehicle Technologies Program to determine the state of the art of advanced flywheel high power energy storage systems to meet hybrid vehicle needs for high power energy storage and energy/power management. Flywheel systems can be implemented with either an electrical or a mechanical powertrain. The assessment elaborates upon flywheel rotor design issues of stress, materials and aspect ratio. Twelve organizations that produce flywheel systems submitted specifications for flywheel energy storage systems to meet minimum energy and power requirements for both light-duty and heavy-duty hybrid applications of interest to DOE. The most extensive experience operating flywheel high power energy storage systems in heavy-duty and light-duty hybrid vehicles is in Europe. Recent advances in Europe in a number of vehicle racing venues and also in road car advanced evaluations are discussed. As a frame of reference, nominal weight and specific power for non-energy storage components of Toyota hybrid electric vehicles are summarized. The most effective utilization of flywheels is in providing high power while providing just enough energy storage to accomplish the power assist mission effectively. Flywheels are shown to meet or exceed the USABC power related goals (discharge power, regenerative power, specific power, power density, weight and volume) for HEV and EV batteries and ultracapacitors. The greatest technical challenge facing the developer of vehicular flywheel systems remains the issue of safety and containment. Flywheel safety issues must be addressed during the design and testing phases to ensure that production flywheel systems can be operated with adequately low risk.

Technology assessment explained by the example of peaceful uses of nuclear energy in the Federal Republic of Germany

International Nuclear Information System (INIS)

Mueller-Brandeck, G.

1986-01-01

The study reviews technology assessment (TA), i.e. the instrument, and the way it has been used and is currently used in the F.R.G., for solving problems induced by technologies. The first part of the study presents the historical background and evolution of nuclear energy policy and discusses the rationality of large-scale technological innovation. The second part deals with the assessment of the nuclear technology, explaining aspects such as social acceptance, the institutional network established for TA, and the 'experiment of parallel research: TA between the two poles of producing an alibi, or creating consensus, assessment of the waste disposal sector, social compatibility, research into problems affecting public acceptance. In conclusion, the study goes into related aspects in connection with nuclear technology assessments, and the social learning process that has set in. (HSCH) [de

Canada's clean energy technology and the Bay area market : a needs assessment

International Nuclear Information System (INIS)

2008-03-01

This study was conducted to develop market intelligence related to clean energy technologies in Northern California, including both commercial and demonstration technologies. The study was developed as a tool for exploring engagement between Canadian and Californian businesses and partnering opportunities. The study examined technologies for solar power and photovoltaics; hydrogen and fuel cells; and waste-to-energy. A list of more than 150 organizations, government agencies, business associations, and utilities was prepared. The survey also included the establishment of contact points with large facilities, public spaces, bus fleets, and major capital projects. Fifty-nine interviews were also conducted as part of the study. Results of the study indicated that the biggest challenge concerning most individuals was the need to reduce energy consumption while maintaining reliability. Many interviewees expressed an interest in operating waste-to-energy facilities. Fifty interviewees indicated that they were planning to use or already used solar technologies. An analysis of clean energy needs was also included. The study indicated that many local governments are reluctant to embrace new, highly visible technologies. Only sophisticated organizations with unique energy demands have considered the use of fuel cell technologies. 1 fig

Technology assessment HTR. Part 8. Nuclear energy and sustainable development

International Nuclear Information System (INIS)

Turkenburg, W.C.

1996-06-01

The small social acceptance of nuclear power for power generation suggests that in the present situation nuclear technology does not meet certain sustainable criteria. First, the concept of sustainable development is explained and which dimensions can be distinguished. Next, the sustainable development with regard to the development of the energy supply is outlined and the energy policy to obtain this situation is discussed. Subsequently, the impact of the sustainable development and the policy used to realize this on the nuclear technology are dealt with. As a result, criteria are formulated that can be used to verify how nuclear technology will meet this criteria and which demands should be used to fit this technology so it can be used in a sustainable development of the society. 55 refs

Future implications of China's energy-technology choices

International Nuclear Information System (INIS)

Larson, E.D.; Wu Zongxin; DeLaquil, Pat; Chen Wenying; Gao Pengfei

2003-01-01

This paper summarizes an assessment of future energy-technology strategies for China that explored the prospects for China to continue its social and economic development while ensuring national energy-supply security and promoting environmental sustainability over the next 50 years. The MARKAL energy-system modeling tool was used to build a model of China's energy system representing all sectors of the economy and including both energy conversion and end-use technologies. Different scenarios for the evolution of the energy system from 1995 to 2050 were explored, enabling insights to be gained into different energy development choices. The analysis indicates a business-as-usual strategy that relies on coal combustion technologies would not be able to meet all environmental and energy security goals. However, an advanced technology strategy emphasizing (1) coal gasification technologies co-producing electricity and clean liquid and gaseous energy carriers (polygeneration), with below-ground storage of some captured CO 2 ; (2) expanded use of renewable energy sources (especially wind and modern biomass); and (3) end-use efficiency would enable China to continue social and economic development through at least the next 50 years while ensuring security of energy supply and improved local and global environmental quality. Surprisingly, even when significant limitations on carbon emissions were stipulated, the model calculated that an advanced energy technology strategy using our technology-cost assumptions would not incur a higher cumulative (1995-2050) total discounted energy system cost than the business-as-usual strategy. To realize such an advanced technology strategy, China will need policies and programs that encourage the development, demonstration and commercialization of advanced clean energy conversion technologies and that support aggressive end-use energy efficiency improvements

Potential for energy technologies in residential and commercial buildings

Energy Technology Data Exchange (ETDEWEB)

Glesk, M.M.

1979-11-01

The residential-commercial energy technology model was developed as a planning tool for policy analysis in the residential and commercial building sectors. The model and its procedures represent a detailed approach to estimating the future acceptance of energy-using technologies both in new construction and for retrofit into existing buildings. The model organizes into an analytical framework all relevant information and data on building energy technology, building markets, and government policy, and it allows for easy identification of the relative importance of key assumptions. The outputs include estimates of the degree of penetration of the various building energy technologies, the levels of energy use savings associated with them, and their costs - both private and government. The model was designed to estimate the annual energy savings associated with new technologies compared with continued use of conventional technology at 1975 levels. The amount of energy used under 1975 technology conditions is referred to as the reference case energy use. For analytical purposes the technologies were consolidated into ten groupings: electric and gas heat pumps; conservation categories I, II, and III; solar thermal (hot water, heating, and cooling); photovoltaics, and wind systems. These groupings clearly do not allow an assessment of the potential for individual technologies, but they do allow a reasonable comparison of their roles in the R/C sector. Assumptions were made regarding the technical and economic performances of the technologies over the period of the analysis. In addition, the study assessed the non-financial characteristics of the technologies - aesthetics, maintenance complexity, reliability, etc. - that will also influence their market acceptability.

Decontamination technology assessment

International Nuclear Information System (INIS)

Allen, R.P.; Konzek, G.J.; Schneider, K.J.; Smith, R.I.

1988-01-01

This study was conducted by the Pacific Northwest Laboratory (PNL) for the U.S. Department of Energy (DOE) to identify and technically assess foreign decontamination and decommissioning (D and D) technology developments that may represent significant improvements over D and D technology currently available or under development in the United States. Technology need areas for nuclear power reactor decommissioning operations were identified and prioritized using the results of past light water rector (LWR) decommissioning studies to quantitatively evaluate the potential for reducing cost and decommissioning worker radiation dose for each major decommissioning activity. Based on these identified needs, current foreign D and D technologies of potential interest to the U.S. were identified through personal contacts and the collection and review of an extensive body of D and D literature. These technologies were then assessed qualitatively to evaluate their uniqueness, potential for a significant reduction in D and D costs and/or worker radiation dose, development status, and other factors affecting their value and applicability to U.S. needs

Assessment of tidal and wave energy conversion technologies in Canada

International Nuclear Information System (INIS)

2009-01-01

This paper presented an attractive option to help meet Canada's future energy needs, notably the vast and energetic Atlantic, Pacific and Arctic coastal waters which make ocean renewable energy, particularly tidal in-stream energy conversion (TISEC) and wave energy conversion (WEC). There is much uncertainty regarding the possible environmental impacts associated with their deployment and operation. In support of commercial development of the industry, a review of scientific knowledge was needed for the development of policy and regulations consistent with Canada's conservation and sustainability priorities. In April 2009, Fisheries and Oceans Canada (DFO) hosted a two-day national science advisory process meeting in order to determine the current state of knowledge on the environmental impacts of tidal and wave energy conversion technologies and their application in the Canadian context based on published reports. Potential mitigation measures were identified and the feasibility of developing a relevant Canadian statement of practice was determined. This report presented an assessment and analysis of wave power, including the impacts on physical processes; impacts on habitat characteristics; impacts on water quality; impacts of noise and vibrations; impacts of electromagnetic fields; impacts of physical encounters; cumulative impacts; and mitigation measures. It was concluded that there is a recognized need to develop and maintain national and regional georeferenced, interoperable, standards-based databases that enable access by governments, developers, academics, non-governmental organizations and the general public. 1 ref., 1 fig.

An assessment of exploiting renewable energy sources with concerns of policy and technology

International Nuclear Information System (INIS)

Shen, Yung-Chi; Lin, Grace T.R.; Li, Kuang-Pin; Yuan, Benjamin J.C.

2010-01-01

In recent years, the Taiwanese government has vigorously promoted the development of renewable energy to engage the challenges of gradual depletion of fossil fuels and oil, as well as the intensification of the greenhouse effect. Since the Sustainable Energy Policy Principles were announced in 2008, Taiwanese government has declared that the development of renewable energy should take into account goals that pertain to energy, the environment, and the economy (3E goals). This study aims to assess the 3E goals and renewable energy sources regulated by the Renewable Energy Development Bill that passed in 2009. The fuzzy analytic hierarchy process (FAHP) is used to resolve the multi-goal problem for achieving our research purposes. That is, this research attempts to reveal the suitable renewable energy sources for the purposes of meeting the 3E policy goals. The results first show that environmental goal is the most important to the development of various renewable energy technologies in Taiwan, followed by the economic and energy goals. Additionally, hydropower, solar energy, and wind energy would be the renewable energy sources utilized in meeting the 3E policy goals. (author)

Technology assessments in transportation: survey of recent literature

Energy Technology Data Exchange (ETDEWEB)

LaBelle, S.J.

1980-03-01

A survey and an evaluation of recent studies of transportation systems done in a technology-assessment framework were undertaken as the basis for a detailed statement of work for a US Department of Energy technology assessment of transportation energy-conservation strategies. Several bibliographies were searched and numerous professionals in the field of technology assessment were contacted regarding current work. Detailed abstracts were prepared for studies judged to be sufficiently broad in coverage of impacts assessed, yet detailed in coverage of all or part of the nation's transportation systems. Some studies were rich in data but not comprehensive in their analytical approach; brief abstracts were prepared for these. An explanation of the criteria used to screen the studies, as well as abstracts of 37 reports, are provided in this compendium of transportation-technology-assessment literature.

Emerging Energy-Efficient Technologies in Buildings Technology Characterizations for Energy Modeling

Energy Technology Data Exchange (ETDEWEB)

Hadley, SW

2004-10-11

The energy use in America's commercial and residential building sectors is large and growing. Over 38 quadrillion Btus (Quads) of primary energy were consumed in 2002, representing 39% of total U.S. energy consumption. While the energy use in buildings is expected to grow to 52 Quads by 2025, a large number of energy-related technologies exist that could curtail this increase. In recent years, improvements in such items as high efficiency refrigerators, compact fluorescent lights, high-SEER air conditioners, and improved building shells have all contributed to reducing energy use. Hundreds of other technology improvements have and will continue to improve the energy use in buildings. While many technologies are well understood and are gradually penetrating the market, more advanced technologies will be introduced in the future. The pace and extent of these advances can be improved through state and federal R&D. This report focuses on the long-term potential for energy-efficiency improvement in buildings. Five promising technologies have been selected for description to give an idea of the wide range of possibilities. They address the major areas of energy use in buildings: space conditioning (33% of building use), water heating (9%), and lighting (16%). Besides describing energy-using technologies (solid-state lighting and geothermal heat pumps), the report also discusses energy-saving building shell improvements (smart roofs) and the integration of multiple energy service technologies (CHP packaged systems and triple function heat pumps) to create synergistic savings. Finally, information technologies that can improve the efficiency of building operations are discussed. The report demonstrates that the United States is not running out of technologies to improve energy efficiency and economic and environmental performance, and will not run out in the future. The five technology areas alone can potentially result in total primary energy savings of between 2 and

Estimating energy-augmenting technological change in developingcountry industries

Energy Technology Data Exchange (ETDEWEB)

Sanstad, Alan H.; Roy, Joyashree; Sathaye, Jayant A.

2006-07-07

Assumptions regarding the magnitude and direction ofenergy-related technological change have long beenrecognized as criticaldeterminants of the outputs and policy conclusions derived fromintegrated assessment models. Particularly in the case of developingcountries, however, empirical analysis of technological change has laggedbehind simulation modeling. This paper presents estimates of sectoralproductivity trends and energy-augmenting technological change forseveral energy-intensive industries in India and South Korea, and, forcomparison, the United States. The key findings are substantialheterogeneity among both industries and countries, and a number of casesof declining energy efficiency. The results are subject to certaintechnical qualifications both in regards to the methodology and to thedirect comparison to integrated assessment parameterizations.Nevertheless, they highlight the importance of closer attention to theempirical basis for common modeling assumptions.

Guidance on the Technology Performance Level (TPL) Assessment Methodology

Energy Technology Data Exchange (ETDEWEB)

Weber, Jochem [National Renewable Energy Lab. (NREL), Golden, CO (United States); Roberts, Jesse D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Babarit, Aurelien [Ecole Centrale de Nantes (France). Lab. of Research in Hydrodynamics, Energetics and Atmospheric Environment (LHEEA); Costello, Ronan [Wave Venture, Penstraze (United Kingdom); Bull, Diana L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neilson, Kim [Ramboll, Copenhagen (Denmark); Bittencourt, Claudio [DNV GL, London (United Kingdom); Kennedy, Ben [Wave Venture, Penstraze (United Kingdom); Malins, Robert Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dykes, Katherine [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-09-01

This document presents the revised Technology Performance Level (TPL) assessment methodology. There are three parts to this revised methodology 1) the Stakeholder Needs and Assessment Guidance (this document), 2) the Technical Submission form, 3) the TPL scoring spreadsheet. The TPL assessment is designed to give a technology neutral or agnostic assessment of any wave energy converter technology. The focus of the TPL is on the performance of the technology in meeting the customer’s needs. The original TPL is described in [1, 2] and those references also detail the critical differences in the nature of the TPL when compared to the more widely used technology readiness level (TRL). (Wave energy TRL is described in [3]). The revised TPL is particularly intended to be useful to investors and also to assist technology developers to conduct comprehensive assessments in a way that is meaningful and attractive to investors. The revised TPL assessment methodology has been derived through a structured Systems Engineering approach. This was a formal process which involved analyzing customer and stakeholder needs through the discipline of Systems Engineering. The results of the process confirmed the high level of completeness of the original methodology presented in [1] (as used in the Wave Energy Prize judging) and now add a significantly increased level of detail in the assessment and an improved more investment focused structure. The revised TPL also incorporates the feedback of the Wave Energy Prize judges.

An enviro-economic function for assessing energy resources for district energy systems

International Nuclear Information System (INIS)

Rezaie, Behnaz; Reddy, Bale V.; Rosen, Marc A.

2014-01-01

District energy (DE) systems provide an important means of mitigating greenhouse gas emissions and the significant related concerns associated with global climate change. DE systems can use fossil fuels, renewable energy and waste heat as energy sources, and facilitate intelligent integration of energy systems. In this study, an enviro-economic function is developed for assessing various energy sources for a district energy system. The DE system is assessed for the considered energy resources by considering two main factors: CO 2 emissions and economics. Using renewable energy resources and associated technologies as the energy suppliers for a DE system yields environmental benefits which can lead to financial advantages through such instruments as tax breaks; while fossil fuels are increasingly penalized by a carbon tax. Considering these factors as well as the financial value of the technology, an analysis approach is developed for energy suppliers of the DE system. In addition, the proposed approach is modified for the case when thermal energy storage is integrated into a DE system. - Highlights: • Developed a function to assess various energy sources for a district energy system. • Considered CO 2 emissions and economics as two main factors. • Applied renewable energy resources technologies as the suppliers for a DE system. • Yields environmental benefits can lead to financial benefits by tax breaks. • Modified enviro-economic function for the TES integrated into a DE system

Geothermal energy utilization and technology

CERN Document Server

Dickson, Mary H; Fanelli, Mario

2013-01-01

Geothermal energy refers to the heat contained within the Earth that generates geological phenomena on a planetary scale. Today, this term is often associated with man's efforts to tap into this vast energy source. Geothermal Energy: utilization and technology is a detailed reference text, describing the various methods and technologies used to exploit the earth's heat. Beginning with an overview of geothermal energy and the state of the art, leading international experts in the field cover the main applications of geothermal energy, including: electricity generation space and district heating space cooling greenhouse heating aquaculture industrial applications The final third of the book focuses upon environmental impact and economic, financial and legal considerations, providing a comprehensive review of these topics. Each chapter is written by a different author, but to a set style, beginning with aims and objectives and ending with references, self-assessment questions and answers. Case studies are includ...

Technology assessment - a workable way out of the 'risk society'?

International Nuclear Information System (INIS)

Mueller-Brandeck-Bocquet, G.

1988-01-01

On the basis of concrete experience and results in the risk assessment process concerning nuclear technology in the Federal Republic of Germany it becomes apparent that technology asessment can make a contribution towards the required technology domestication. The 'risk management' of the circle of nuclear power generators and the consulting and licensing bodies having failed, a new phase of technology assessment began in 1970, whereby proponents and opponents of nuclear energy had a say. Parallel research on the safety of light water reactors and fast breeders gave valuable insight into the danger potential of nuclear energy while the latent risk of technology assessment misuse became apparent in the decision-finding process concerning the problem of radioactive waste management. In the end it were the Enquete Commission 'Future Nuclear Energy Policy' of the German Bundestag and the studies on social agreeability of energy supply systems which resulted in the perspective of a future without the use of nuclear power being a realistic option. The general findings of technology assessment, e.g. the cognition that there can be no scientific decision in favour of assuming responsibility for nuclear energy, opens up new views and possibilities for acting for the decision-makers in the field of energy policy. (orig./HSCH) [de

Canada's clean energy technology and the southern California market : a needs assessment

International Nuclear Information System (INIS)

2008-01-01

This report presented a study whose purpose was to develop targeted market intelligence regarding the specific needs and plans of southern California-based organizations that are interested in procuring or using clean energy technologies for demonstration or commercial purposes. Industry Canada and the Canadian Consulate General in Los Angeles planned to utilize the study as a tool to explore business development or partnering opportunities between Canada/Canadian industry and California entities. The report described the study objective and provided a definition of clean energy technology. Clean energy was defined as any energy that causes little or no harm to the environment. The study scope was also presented. The study focused on opportunities in the following areas: solar power and photovoltaic technologies; hydrogen and fuel cells technologies; and thermochemical waste-to-energy systems. Context was discussed in terms of California's energy drivers, and California clean energy initiatives and experience. The results of a survey conducted with 350 organizations in southern California were also outlined for facilities and capital projects; fleets and mobile sources; and parks and public spaces. Last, the report presented an analysis of the California marketplace and solar power, hydrogen and fuel cells, and waste-to-energy. 14 refs

Wave energy resource assessment and review of the technologies

Energy Technology Data Exchange (ETDEWEB)

Wan Nik, W.B.: Sulaiman, O.O. [Maritime Technology Department, Universiti Malaysia Terengganu, 21030, Kuala Terengganu (Malaysia); Rosliza, R. [TATI University College, Teluk Kalong, 24000 Kemaman, Terengganu, (Malaysia); Prawoto, Y. [Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM, Skudai, Johor (Malaysia); Muzathik, A.M. [Institute of Technology, University of Moratuwa (Sri Lanka)

2011-07-01

Increase in human population has increased the demand for more energy. Technical improvement in transport and electrical appliances gives a lot of facilities to our life nowadays. Still we need to generate or convert this energy. Energy generation based on conventional technologies is always accompanied by environmental pollution. It gives overheating and greenhouse effects that later result in biosphere degradation. Nowadays sea wave energy is being increasingly regarded in many countries as a major and promising resource. It is renewable and environmentally friendly. In this paper wave parameters related to wave energy is analyzed. Then the paper describes the development of many different types of wave-energy converters. Several topics are addressed; the characterization of the wave energy resource, range of devices and how such devices can be organized into classes.

Energy technology perspectives - scenarios and strategies to 2050

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-11-03

At their 2005 summit in Gleneagles, G8 leaders confronted questions of energy security and supply and lowering of CO{sub 2} emissions and decided to act with resolve and urgency. They called upon the International Energy Agency to provide advice on scenarios and strategies for a clean and secure energy future. Energy Technology Perspectives is a response to the G8 request. This work demonstrates how energy technologies can make a difference in a series of global scenarios to 2050. It reviews in detail the status and prospects of key energy technologies in electricity generation, buildings, industry and transport. It assesses ways the world can enhance energy security and contain growth in CO{sub 2} emissions by using a portfolio of current and emerging technologies. Major strategic elements of a successful portfolio are energy efficiency, CO{sub 2} capture and storage, renewables and nuclear power. 110 figs., 4 annexes.

Renewable energy-driven innovative energy-efficient desalination technologies

International Nuclear Information System (INIS)

Ghaffour, Noreddine; Lattemann, Sabine; Missimer, Thomas; Ng, Kim Choon; Sinha, Shahnawaz; Amy, Gary

2014-01-01

Highlights: • Renewable energy-driven desalination technologies are highlighted. • Solar, geothermal, and wind energy sources were explored. • An innovative hybrid approach (combined solar–geothermal) has also been explored. • Innovative desalination technologies developed by our group are discussed. • Climate change and GHG emissions from desalination are also discussed. - Abstract: Globally, the Kingdom of Saudi Arabia (KSA) desalinates the largest capacity of seawater but through energy-intensive thermal processes such as multi-stage flash (MSF) distillation (>10 kW h per m 3 of desalinated water, including electrical and thermal energies). In other regions where fossil energy is more expensive and not subsidized, seawater reverse osmosis (SWRO) is the most common desalination technology but it is still energy-intensive (3–4 kW h e /m 3 ). Both processes therefore lead to the emission of significant amounts of greenhouse gases (GHGs). Moreover, MSF and SWRO technologies are most often used for large desalination facilities serving urban centers with centralized water distribution systems and power grids. While renewable energy (RE) sources could be used to serve centralized systems in urban centers and thus provide an opportunity to make desalination greener, they are mostly used to serve rural communities off of the grid. In the KSA, solar and geothermal energy are of most relevance in terms of local conditions. Our group is focusing on developing new desalination processes, adsorption desalination (AD) and membrane distillation (MD), which can be driven by waste heat, geothermal or solar energy. A demonstration solar-powered AD facility has been constructed and a life cycle assessment showed that a specific energy consumption of <1.5 kW h e /m 3 is possible. An innovative hybrid approach has also been explored which would combine solar and geothermal energy using an alternating 12-h cycle to reduce the probability of depleting the heat source

Thermal energy storage technologies for sustainability systems design, assessment and applications

CERN Document Server

Kalaiselvam, S

2014-01-01

Thermal Energy Storage Technologies for Sustainability is a broad-based overview describing the state-of-the-art in latent, sensible, and thermo-chemical energy storage systems and their applications across industries. Beginning with a discussion of the efficiency and conservation advantages of balancing energy demand with production, the book goes on to describe current state-of-the art technologies. Not stopping with description, the authors also discuss design, modeling, and simulation of representative systems, and end with several case studies of systems in use.Describes how thermal energ

The impacts of wind technology advancement on future global energy

International Nuclear Information System (INIS)

Zhang, Xiaochun; Ma, Chun; Song, Xia; Zhou, Yuyu; Chen, Weiping

2016-01-01

Highlights: • Integrated assessment model perform a series of scenarios of technology advances. • Explore the potential roles of wind energy technology advance in global energy. • Technology advance impacts on energy consumption and global low carbon market. • Technology advance influences on global energy security and stability. - Abstract: To avoid additional global warming and environmental damage, energy systems need to rely on the use of low carbon technologies like wind energy. However, supply uncertainties, production costs, and energy security are the main factors considered by the global economies when reshaping their energy systems. Here, we explore the potential roles of wind energy technology advancement in future global electricity generations, costs, and energy security. We use an integrated assessment model performing a series of technology advancement scenarios. The results show that double of the capital cost reduction causes 40% of generation increase and 10% of cost ​decrease on average in the long-term global wind electricity market. Today’s technology advancement could bring us the benefit of increasing electricity production in the future 40–50 years, and decreasing electricity cost in the future 90–100 years. The technology advancement of wind energy can help to keep global energy security and stability. An aggressive development and deployment of wind energy could in the long-term avoid 1/3 of gas and 1/28 of coal burned, and keep 1/2 biomass and 1/20 nuclear fuel saved from the global electricity system. The key is that wind resources are free and carbon-free. The results of this study are useful in broad coverage ranges from innovative technologies and systems of renewable energy to the economic industrial and domestic use of energy with no or minor impact on the environment.

Development of Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Iron and Steel Sector

Energy Technology Data Exchange (ETDEWEB)

Xu, T.T.; Sathaye, J.; Galitsky, C.

2010-09-30

Adoption of efficient end-use technologies is one of the key measures for reducing greenhouse gas (GHG) emissions. With the working of energy programs and policies on carbon regulation, how to effectively analyze and manage the costs associated with GHG reductions become extremely important for the industry and policy makers around the world. Energy-climate (EC) models are often used for analyzing the costs of reducing GHG emissions (e.g., carbon emission) for various emission-reduction measures, because an accurate estimation of these costs is critical for identifying and choosing optimal emission reduction measures, and for developing related policy options to accelerate market adoption and technology implementation. However, accuracies of assessing of GHG-emission reduction costs by taking into account the adoption of energy efficiency technologies will depend on how well these end-use technologies are represented in integrated assessment models (IAM) and other energy-climate models. In this report, we first conduct brief overview on different representations of end-use technologies (mitigation measures) in various energy-climate models, followed by problem statements, and a description of the basic concepts of quantifying the cost of conserved energy including integrating non-regrets options. A non-regrets option is defined as a GHG reduction option that is cost effective, without considering their additional benefits related to reducing GHG emissions. Based upon these, we develop information on costs of mitigation measures and technological change. These serve as the basis for collating the data on energy savings and costs for their future use in integrated assessment models. In addition to descriptions of the iron and steel making processes, and the mitigation measures identified in this study, the report includes tabulated databases on costs of measure implementation, energy savings, carbon-emission reduction, and lifetimes. The cost curve data on mitigation

The United States Department of Energy Office of Industrial Technology`s Technology Benefits Recording System

Energy Technology Data Exchange (ETDEWEB)

Hughes, K.R.; Moore, N.L.

1994-09-01

The U.S. Department of Energy (DOE) Office of Industrial Technology`s (OIT`s) Technology Benefits Recording System (TBRS) was developed by Pacific Northwest Laboratory (PNL). The TBRS is used to organize and maintain records of the benefits accrued from the use of technologies developed with the assistance of OIT. OIT has had a sustained emphasis on technology deployment. While individual program managers have specific technology deployment goals for each of their ongoing programs, the Office has also established a separate Technology Deployment Division whose mission is to assist program managers and research and development partners commercialize technologies. As part of this effort, the Technology Deployment Division developed an energy-tracking task which has been performed by PNL since 1977. The goal of the energy-tracking task is to accurately assess the energy savings impact of OIT-developed technologies. In previous years, information on OIT-sponsored technologies existed in a variety of forms--first as a hardcopy, then electronically in several spreadsheet formats that existed in multiple software programs. The TBRS was created in 1993 for OIT and was based on information collected in all previous years from numerous industrial contacts, vendors, and plants that have installed OIT-sponsored technologies. The TBRS contains information on technologies commercialized between 1977 and the present, as well as information on emerging technologies in the late development/early commercialization stage of the technology life cycle. For each technology, details on the number of units sold and the energy saved are available on a year-by-year basis. Information regarding environmental benefits, productivity and competitiveness benefits, or impact that the technology may have had on employment is also available.

Estimating energy-augmenting technological change in developing country industries

International Nuclear Information System (INIS)

Sanstad, Alan H.; Roy, Joyashree; Sathaye, Jayant A.

2006-01-01

Assumptions regarding the magnitude and direction of energy-related technological change have long been recognized as critical determinants of the outputs and policy conclusions derived from integrated assessment models. Particularly in the case of developing countries, however, empirical analysis of technological change has lagged behind simulation modeling. This paper presents estimates of sectoral productivity trends and energy-augmenting technological change for several energy-intensive industries in India and South Korea, and, for comparison, the United States. The key findings are substantial heterogeneity among both industries and countries, and a number of cases of declining energy efficiency. The results are subject to certain technical qualifications both in regards to the methodology and to the direct comparison to integrated assessment parameterizations. Nevertheless, they highlight the importance of closer attention to the empirical basis for common modeling assumptions

Indicative energy technology assessment of UK shale gas extraction

International Nuclear Information System (INIS)

Hammond, Geoffrey P.; O’Grady, Áine

2017-01-01

Highlights: • UK shale gas ‘fracking’ is at a very early stage with an uncertain size of resource. • Shale gas extraction might benefit UK fuel security, as well as jobs and growth. • Potentially harmful environmental ‘side-effects’ must be monitored and regulated. • Gas bills for UK household and industrial consumers are unlikely to fall sharply. • Costs & benefits of shale gas fracking are unevenly distributed between communities. - Abstract: There is at present much interest in unconventional sources of natural gas, especially in shale gas which is obtained by hydraulic fracturing, or ‘fracking’. Boreholes are drilled and then lined with steel tubes so that a mixture of water and sand with small quantities of chemicals – the fracking fluid – can be pumped into them at very high pressure. The sand grains that wedge into the cracks induced in the shale rock by a ‘perforating gun’ then releases gas which returns up the tubes. In the United Kingdom (UK) exploratory drilling is at an early stage, with licences being issued to drill a limited number of test boreholes around the country. However, such activities are already meeting community resistance and controversy. Like all energy technologies it exhibits unwanted ‘side-effects’; these simply differ in their level of severity between the various options. Shale gas may make, for example, a contribution to attaining the UK’s statutory ‘greenhouse gas’ emissions targets, but only if appropriate and robust regulations are enforced. The benefits and disadvantages of shale gas fracking are therefore discussed in order to illustrate a ‘balance sheet’ approach. It is also argued that it is desirable to bring together experts from a range of disciplines in order to carry out energy technology assessments. That should draw on and interact with national and local stakeholders: ‘actors’ both large and small. Community engagement in a genuinely participative process – where the

Technology needs assessment for DOE environmental restoration programs

International Nuclear Information System (INIS)

Duray, J.R.; Carlson, T.J.; Carpenter, C.E.; Cummins, L.E.; Daub, G.J.

1992-01-01

The 'Technology Needs Assessment Final Report' describes current and planned environmental restoration activity, identifies technologies intended to be used or under consideration, and ranks technology deficiencies in the U.S. Department of Energy's environmental restoration program. Included in the ranking are treatment technologies, characterization technologies, and non-technology issues that affect environmental restoration. Data used for the assessment was gathered during interviews in the spring of 1991 with DOE site personnel responsible for the environmental restoration work. (author)

Energy research and energy technology

International Nuclear Information System (INIS)

Anon.

1991-01-01

Research and development in the field of energy technologies was and still is a rational necessity of our time. However, the current point of main effort has shifted from security of supply to environmental compatibility and safety of the technological processes used. Nuclear fusion is not expected to provide an extension of currently available energy resources until the middle of the next century. Its technological translation will be measured by the same conditions and issues of political acceptance that are relevant to nuclear technology today. Approaches in the major research establishments to studies of regenerative energy systems as elements of modern energy management have led to research and development programs on solar and hydrogen technologies as well as energy storage. The percentage these systems might achieve in a secured energy supply of European national economies is controversial yet today. In the future, the Arbeitsgemeinschaft Grossforschungseinrichtungen (AGF) (Cooperative of Major Research Establishments) will predominantly focus on nuclear safety research and on areas of nuclear waste disposal, which will continue to be a national task even after a reorganization of cooperation in Europe. In addition, they will above all assume tasks of nuclear plant safety research within international cooperation programs based on government agreements, in order to maintain access for the Federal Republic of Germany to an advancing development of nuclear technology in a concurrent partnership with other countries. (orig./HSCH) [de

Sourcebook for energy assessment. [Reference Energy Systems for 1972-2020

Energy Technology Data Exchange (ETDEWEB)

Beller, M. (ed.)

1975-12-01

An analytical approach is presented that is broadly applicable to the assessment of energy technologies and policies. Using the Reference Energy System approach, it permits the examination of the economic, environmental, and resource implications resulting from the substitution of one fuel or technology for another. Included as tools for such analyses are the necessary data and methodology, as well as a set of Reference Energy Systems covering the 1972-2020 period to serve as baselines for the perturbation analyses of interest. 46 tables, 25 figures, 71 references.

Electrochemical conversion technologies for optimal design of decentralized multi-energy systems : Modeling framework and technology assessment

NARCIS (Netherlands)

Gabrielli, Paolo; Gazzani, Matteo; Mazzotti, Marco

2018-01-01

The design and operation of integrated multi-energy systems require models that adequately describe the behavior of conversion and storage technologies. Typically, linear conversion performance or fixed data from technology manufacturers are employed, especially for new or advanced technologies.

Promoting renewable energy technologies

International Nuclear Information System (INIS)

Grenaa Jensen, S.

2004-06-01

Technologies using renewable energy sources are receiving increasing interest from both public authorities and power producing companies, mainly because of the environmental advantages they procure in comparison with conventional energy sources. These technologies can be substitution for conventional energy sources and limit damage to the environment. Furthermore, several of the renewable energy technologies satisfy an increasing political goal of self-sufficiency within energy production. The subject of this thesis is promotion of renewable technologies. The primary goal is to increase understanding on how technological development takes place, and establish a theoretical framework that can assist in the construction of policy strategies including instruments for promotion of renewable energy technologies. Technological development is analysed by through quantitative and qualitative methods. (BA)

Socio-economic research for innovative energy technologies

Energy Technology Data Exchange (ETDEWEB)

Ogawa, Yuichi [Tokyo Univ., High Temperature Plasma Center, Kashiwa, Chiba (Japan); Okano, Kunihiko [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

2006-10-15

In the 21st century global environment and energy issues become very important, and this is characterized by the long-term (in the scale of a few tens years) and world-wide issue. In addition, future prospect of these issues might be quite uncertain, and scientific prediction could be very difficult. For these issues vigorous researches and various efforts have been carried out from various aspects; e.g., world-wide discussion such as COP3 in Kyoto, promotion of the energy-saving technology and so on. Development of environment-friendly energy has been promoted, and new innovative technologies are explored. Nuclear fusion is, of course, a promising candidate. While, there might be some criticism for nuclear fusion from the socio-economic aspect; e.g., it would take long time and huge cost for the fusion reactor development. In addition, other innovative energy technologies might have their own criticism, as well. Therefore, socio-economic research might be indispensable for future energy resources. At first we have selected six items as for the characteristics, which might be important for future energy resources; i.e., energy resource, environmental load, economics, reliability/stability, flexibility on operation and safety/security. Concerning to innovative energy technologies, we have nominated seven candidates; i.e., advanced coal technology with CO2 recovery system, SOFC top combined cycle, solar power, wind power, space solar power station, advanced fission and fusion. Based on questionnaires for ordinary people and fusion scientists, we have tried to assess the fusion energy development, comparing with other innovative energy technologies. (author)

Survey report of FY 1997 on the long-term energy technology strategy. Survey on the pre-assessment system of energy and environmental technology research and development; 1997 nendo chosa hokokusho (choki energy gijutsu senryaku chosa). Energy kankyo gijutsu kenkyu kaihatsu no jizen hyoka ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To select projects of the New Sunshine Program which is the locomotive for Japan`s research and development of energy and environmental technologies and to map out the Program`s long-term strategy, it is required to develop an effective methodology of assessing research and development themes. It is also necessary to establish the pre-assessment system which makes the assessment process more logical and which will enable the priority setting among different themes on the basis of objective and quantitative analysis. Additionally, transparency should be ensured for such a pre-assessment process through disclosure to the public and other means. The present survey aims to concretize the pre-assessment system by studying the system and techniques of an assessment system which is applicable to the research and development themes of the New Sunshine Program and is objective, quantitative and logical and which can ensure transparency and by receiving suggestions on the pre-assessment of Japan`s research and development of energies and environmental technologies through research on overseas trends of government-led research and development. 3 refs., 7 figs., 26 tabs.

Life cycle energy use and GHG emission assessment of coal-based SNG and power cogeneration technology in China

International Nuclear Information System (INIS)

Li, Sheng; Gao, Lin; Jin, Hongguang

2016-01-01

Highlights: • Life cycle energy use and GHG emissions are assessed for SNG and power cogeneration. • A model based on a Chinese domestic database is developed for evaluation. • Cogeneration shows lower GHG emissions than coal-power pathway. • Cogeneration has lower life cycle energy use than supercritical coal-power pathway. • Cogeneration is a good option to implement China’s clean coal technologies. - Abstract: Life cycle energy use and GHG emissions are assessed for coal-based synthetic natural gas (SNG) and power cogeneration/polygenereation (PG) technology and its competitive alternatives. Four main SNG applications are considered, including electricity generation, steam production, SNG vehicle and battery electric vehicle (BEV). Analyses show that if SNG is produced from a single product plant, the lower limits of its life cycle energy use and GHG emissions can be comparable to the average levels of coal-power and coal-BEV pathways, but are still higher than supercritical and ultra supercritical (USC) coal-power and coal-BEV pathways. If SNG is coproduced from a PG plant, when it is used for power generation, steam production, and driving BEV car, the life cycle energy uses for PG based pathways are typically lower than supercritical coal-power pathways, but are still 1.6–2.4% higher than USC coal-power pathways, and the average life cycle GHG emissions are lower than those of all coal-power pathways including USC units. If SNG is used to drive vehicle car, the life cycle energy use and GHG emissions of PG-SNGV-power pathway are both much higher than all combined coal-BEV and coal-power pathways, due to much higher energy consumption in a SNG driven car than in a BEV car. The coal-based SNG and power cogeneration technology shows comparable or better energy and environmental performances when compared to other coal-based alternatives, and is a good option to implement China’s clean coal technologies.

Renewable energy-driven innovative energy-efficient desalination technologies

KAUST Repository

Ghaffour, NorEddine; Lattemann, Sabine; Missimer, Thomas M.; Ng, Kim Choon; Sinha, Shahnawaz; Amy, Gary L.

2014-01-01

Globally, the Kingdom of Saudi Arabia (KSA) desalinates the largest capacity of seawater but through energy-intensive thermal processes such as multi-stage flash (MSF) distillation (>10 kW h per m3 of desalinated water, including electrical and thermal energies). In other regions where fossil energy is more expensive and not subsidized, seawater reverse osmosis (SWRO) is the most common desalination technology but it is still energy-intensive (3-4 kW h_e/m3). Both processes therefore lead to the emission of significant amounts of greenhouse gases (GHGs). Moreover, MSF and SWRO technologies are most often used for large desalination facilities serving urban centers with centralized water distribution systems and power grids. While renewable energy (RE) sources could be used to serve centralized systems in urban centers and thus provide an opportunity to make desalination greener, they are mostly used to serve rural communities off of the grid. In the KSA, solar and geothermal energy are of most relevance in terms of local conditions. Our group is focusing on developing new desalination processes, adsorption desalination (AD) and membrane distillation (MD), which can be driven by waste heat, geothermal or solar energy. A demonstration solar-powered AD facility has been constructed and a life cycle assessment showed that a specific energy consumption of <1.5 kW h_e/m3 is possible. An innovative hybrid approach has also been explored which would combine solar and geothermal energy using an alternating 12-h cycle to reduce the probability of depleting the heat source within the geothermal reservoir and provide the most effective use of RE without the need for energy storage. This paper highlights the use of RE for desalination in KSA with a focus on our group's contribution in developing innovative low energy-driven desalination technologies. © 2014 Elsevier Ltd. All rights reserved.

Renewable energy-driven innovative energy-efficient desalination technologies

KAUST Repository

Ghaffour, Noreddine

2014-04-13

Globally, the Kingdom of Saudi Arabia (KSA) desalinates the largest capacity of seawater but through energy-intensive thermal processes such as multi-stage flash (MSF) distillation (>10 kW h per m3 of desalinated water, including electrical and thermal energies). In other regions where fossil energy is more expensive and not subsidized, seawater reverse osmosis (SWRO) is the most common desalination technology but it is still energy-intensive (3-4 kW h_e/m3). Both processes therefore lead to the emission of significant amounts of greenhouse gases (GHGs). Moreover, MSF and SWRO technologies are most often used for large desalination facilities serving urban centers with centralized water distribution systems and power grids. While renewable energy (RE) sources could be used to serve centralized systems in urban centers and thus provide an opportunity to make desalination greener, they are mostly used to serve rural communities off of the grid. In the KSA, solar and geothermal energy are of most relevance in terms of local conditions. Our group is focusing on developing new desalination processes, adsorption desalination (AD) and membrane distillation (MD), which can be driven by waste heat, geothermal or solar energy. A demonstration solar-powered AD facility has been constructed and a life cycle assessment showed that a specific energy consumption of <1.5 kW h_e/m3 is possible. An innovative hybrid approach has also been explored which would combine solar and geothermal energy using an alternating 12-h cycle to reduce the probability of depleting the heat source within the geothermal reservoir and provide the most effective use of RE without the need for energy storage. This paper highlights the use of RE for desalination in KSA with a focus on our group\\'s contribution in developing innovative low energy-driven desalination technologies. © 2014 Elsevier Ltd. All rights reserved.

Likely market-penetrations of renewable-energy technologies

International Nuclear Information System (INIS)

Probert, S.D.; Mackay, R.M.

1998-01-01

The learning-curve concept is considered to be an important tool for predicting the future costs of renewable-energy technology systems. This paper sets out the underlying rationale for learning-curve theory and the potential for its application to renewable technologies, such as photovoltaic-module and wind-power generator technologies. An indication of the data requirements for carrying out learning-curve projections is given together with an assessment of the requirements necessary for an analysis to be undertaken of the application of learning curves to other renewable-energy technologies. The paper includes a cost comparison and a figure-of-merit criterion applicable to photovoltaic-module and wind-power-turbine technologies. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

Energy Technology.

Science.gov (United States)

Eaton, William W.

Reviewed are technological problems faced in energy production including locating, recovering, developing, storing, and distributing energy in clean, convenient, economical, and environmentally satisfactory manners. The energy resources of coal, oil, natural gas, hydroelectric power, nuclear energy, solar energy, geothermal energy, winds, tides,…

Energy technologies and energy efficiency in economic modelling

DEFF Research Database (Denmark)

Klinge Jacobsen, Henrik

1998-01-01

This paper discusses different approaches to incorporating energy technologies and technological development in energy-economic models. Technological development is a very important issue in long-term energy demand projections and in environmental analyses. Different assumptions on technological ...... of renewable energy and especially wind power will increase the rate of efficiency improvement. A technologically based model in this case indirectly makes the energy efficiency endogenous in the aggregate energy-economy model....... technological development. This paper examines the effect on aggregate energy efficiency of using technological models to describe a number of specific technologies and of incorporating these models in an economic model. Different effects from the technology representation are illustrated. Vintage effects...... illustrates the dependence of average efficiencies and productivity on capacity utilisation rates. In the long run regulation induced by environmental policies are also very important for the improvement of aggregate energy efficiency in the energy supply sector. A Danish policy to increase the share...

Establishment of a bioassay system for cancer risk assessment in energy technology

Energy Technology Data Exchange (ETDEWEB)

Ts' o, P.O.P.; Bruce, S.A.; Brown, A. (eds.)

1983-09-01

Separate abstracts were prepared for 20 papers in this report. For several years the Department of Energy (DOE), Office of Health and Environmental Research (OHER), has supported a research program aimed at developing new experimental approaches for the improvement of cancer risk assessments. The central issue is to overcome the organizational, species and other barriers that make it difficult to extrapolate laboratory-based data to predict risk to man. Most of the participants at the meeting are involved in research aimed at understanding the mechanism(s) of chemical carcinogenesis. Complex mixtures of chemicals are associated with many energy technologies. DOE's initial program emphasis focused on semi-applied research aimed at quantitative evaluation of carcinogenic activity of complex materials. Since much progress has been made in DOE integrated technology-specific chemical-biological characterization studies, the number and kinds of chemicals of concern has been reduced to a relatively few well-defined classes. Although the classes of compounds seem to be unique to some of the synfuel technologies, they are quite similar to compounds of general interest, for example, poly-nuclear aromatic hydrocarbons. Special emphasis was placed on molecular and cellular dosimetry as one of the key requirements for quantitative comparison of effects at the cell level in vivo and in vitro. Although it is relatively easy to measure cell, tissue, organ and whole organism doses associated with radiation exposures, we are just learning how to do this for chemical agents. Several methods have been developed in the past several years which can be used.

Stimulating R and D of industrial energy-efficient technology. Policy lessons--impulse technology

International Nuclear Information System (INIS)

Luiten, Esther; Blok, Kornelis

2004-01-01

Stimulating research and development (R and D) of innovative energy-efficient technologies for industry is an attractive option for reducing greenhouse gas emissions. Impulse technology, an innovative papermaking technology, is always included in studies assessing the long-term potential of industrial energy efficiency. Aim of this article is to analyse the R and D trajectory of impulse technology in order to explore how government can stimulate the development of industrial energy-efficient technology. The concept of 'momentum' is used to characterise the network of actors and to understand the effect of government R and D support in this particular case study. The network analysis convincingly shows that although marketed as an energy-efficient technology, other benefits were in fact driving forces. Researchers at various national pulp and paper research institutes were successful in attracting government R and D support by claiming an improved energy efficiency. The momentum of the technology network was modest between 1980 and 1990. Therefore, government R and D support accelerated the development of impulse technology in this period. However, when the perspectives of the technology deteriorated--momentum decreased--researchers at national research institutes continued to attract government R and D support successfully. But 25 years of R and D--and over 15 years government R and D support--have not yet resulted in a proven technology. The case study illustrates the risk of continuing R and D support too long without taking into account actors' drivers to invest in R and D. Once momentum decreased, government should have been more circumspect in evaluating the (energy efficiency) promise of impulse technology. The major policy lesson is that government has to look beyond claimed energy efficiencies; government has to value (qualitative) information on (changing) technology networks in deciding upon starting, continuing or pulling out financial R and D support to

EASETECH Energy: Life Cycle Assessment of current and future Danish power systems

DEFF Research Database (Denmark)

Turconi, Roberto; Damgaard, Anders; Bisinella, Valentina

A new life cycle assessment (LCA) model software has been developed by DTU Environment, to facilitate detailed LCA of energy technologies. The model, EASETECH Energy, is dedicated to the specific technologies needed to assess energy production and energy systems and provides an unprecedented...

Health risks of energy technologies

International Nuclear Information System (INIS)

Travis, C.C.; Etnier, E.L.

1983-01-01

This volume examines occupational, public health, and environmental risks of the coal fuel cycle, the nuclear fuel cycle, and unconventional energy technologies. The 6 chapters explore in detail the relationship between energy economics and risk analysis, assess the problems of applying traditional cost-benefit analysis to long-term environmental problems (such as global carbon dioxide levels), and consider questions about the public's perception and acceptance of risk. Also included is an examination of the global risks associated with current and proposed levels of energy production and comsumption from all major sources. A separate abstract was prepared for each of the 6 chapters; all are included in Energy Abstracts for Policy Analysis (EAPA) and four in Energy Research Abstracts

Canada's clean energy technology and the Bay area market : a needs assessment

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-03-15

This study was conducted to develop market intelligence related to clean energy technologies in Northern California, including both commercial and demonstration technologies. The study was developed as a tool for exploring engagement between Canadian and Californian businesses and partnering opportunities. The study examined technologies for solar power and photovoltaics; hydrogen and fuel cells; and waste-to-energy. A list of more than 150 organizations, government agencies, business associations, and utilities was prepared. The survey also included the establishment of contact points with large facilities, public spaces, bus fleets, and major capital projects. Fifty-nine interviews were also conducted as part of the study. Results of the study indicated that the biggest challenge concerning most individuals was the need to reduce energy consumption while maintaining reliability. Many interviewees expressed an interest in operating waste-to-energy facilities. Fifty interviewees indicated that they were planning to use or already used solar technologies. An analysis of clean energy needs was also included. The study indicated that many local governments are reluctant to embrace new, highly visible technologies. Only sophisticated organizations with unique energy demands have considered the use of fuel cell technologies. 1 fig.

Evolution of the global energy system: technology and other factors

Energy Technology Data Exchange (ETDEWEB)

de Leone, R.

Future directions in government energy policies are assessed in light of the energy evolution following the 1973 oil crisis and the impacts created by technology transfer and other factors. In particular, the paper examines changes which are occurring in global marketing and commercialization trends, and in public opinion, especially in response to the techniques employed by planners in assessing new energy sources and technologies designed to lessen dependency on oil imports. It is noted that greater consideration must be given by scientists and engineers to the socio-economic impacts of their research efforts.

Assessment of environmental external effects in the production of energy

DEFF Research Database (Denmark)

Schleisner, L.; Meyer, H.J.; Morthorst, P.E.

1995-01-01

A project in Denmark has been carried out with the purpose to assess the environmental damages and the external costs in the production of energy. The energy production technologies that will be reported in this paper are wind power and a conventional coal fired plant. In the project the environm......A project in Denmark has been carried out with the purpose to assess the environmental damages and the external costs in the production of energy. The energy production technologies that will be reported in this paper are wind power and a conventional coal fired plant. In the project...... the environmental damages for the energy production technologies are compared, and externalities in the production of energy using renewable energy and fossil fuels are identified, estimated and monetized....

New energy technologies. Report; Nouvelles technologies de l'energie. Rapport

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This report on the new energy technologies has been written by a working group on request of the French ministry of economy, finances and industry, of the ministry of ecology and sustainable development, of the ministry of research and new technologies and of the ministry of industry. The mission of the working group is to identify goals and priority ways for the French and European research about the new technologies of energy and to propose some recommendations about the evolution of research incentive and sustain systems in order to reach these goals. The working group has taken into consideration the overall stakes linked with energy and not only the climatic change. About this last point, only the carbon dioxide emissions have been considered because they represent 90% of the greenhouse gases emissions linked with the energy sector. A diagnosis is made first about the present day context inside which the new technologies will have to fit with. Using this diagnosis, the research topics and projects to be considered as priorities for the short-, medium- and long-term have been identified: energy efficiency in transports, in dwellings/tertiary buildings and in the industry, development for the first half of the 21. century of an energy mix combining nuclear, fossil-fuels and renewable energy sources. (J.S.)

Performance of renewable energy technologies in the energy-environmental-economic continuum

International Nuclear Information System (INIS)

Guthrie, B.M.; Birkenheier, T.L.

1993-01-01

Projected cost-performance data are used to calculate the Canadian commercial potential of selected renewable energy technologies to the year 2010. Based on projected market penetration, the extent to which renewable energy can contribute to environmental initiatives is also examined. The potential for renewable energy to contribute to the Canadian electricity supply is limited neither by the state of the technology nor the extent of the resource available. Barriers to acceptance of renewables include high initial capital costs, intermittent nature of much of the energy supply, land requirements, onerous requirements for environmental assessments and licensing, and lack of government policies which consider the externalities involved in new energy supply. Environmental benefits which will drive the adoption of renewables in Canada include the sustainable nature of renewable resources, low environmental impacts, and suitability for integrated resource planning. In addition, the cost performance of renewable technologies is improving rapidly. Under base-case scenarios, at current buyback rates, only small hydro and biomass of the five renewable technologies examined has significant commercial potential in Canada. At buyback rates that reflect currently projected avoided costs plus an additional 2 cents per kWh as an environmental premium, all five renewable technologies except for photovoltaics have appreciable commercial potential achievable by 2010. The quantity of electrical energy displaced under this latter scenario is estimated at 49 TWh/y, or 7% of the projected total generation in Canada. 2 figs., 2 tabs

Life cycle assessment of thermal Waste-to-Energy technologies: Review and recommendations

DEFF Research Database (Denmark)

Astrup, Thomas Fruergaard; Tonini, Davide; Turconi, Roberto

2015-01-01

composition, technology, gas cleaning, energy recovery, residue management, and inventory data), and (iii) modeling principles (e.g. energy/mass calculation principles, energy substitution, inclusion of capital goods and uncertainty evaluation). Very few of the published studies provided full and transparent...

The National Energy Strategy - The role of geothermal technology development: Proceedings

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

Each year the Geothermal Division of the US Department of Energy conducts an in-depth review of its entire geothermal R D program. The conference serves several purposes: a status report on current R D activities, an assessment of progress and problems, a review of management issues, and a technology transfer opportunity between DOE and the US geothermal industry. Topics in this year's conference included Hydrothermal Energy Conversion Technology, Hydrothermal Reservoir Technology, Hydrothermal Hard Rock Penetration Technology, Hot Dry Rock Technology, Geopressured-Geothermal Technology and Magma Energy Technology. Each individual paper has been cataloged separately.

Technology and the diffusion of renewable energy

International Nuclear Information System (INIS)

Popp, David; Hascic, Ivan; Medhi, Neelakshi

2011-01-01

We consider investment in wind, solar photovoltaic, geothermal, and electricity from biomass and waste across 26 OECD countries from 1991 to 2004. Using the PATSTAT database, we obtain a comprehensive list of patents for each of these technologies throughout the world, which we use to assess the impact of technological change on investment in renewable energy capacity. We consider four alternative methods for counting patents, using two possible filters: weighting patents by patent family size and including only patent applications filed in multiple countries. For each patent count, we create knowledge stocks representing the global technological frontier. We find that technological advances do lead to greater investment, but the effect is small. Investments in other carbon-free energy sources, such as hydropower and nuclear power, serve as substitutes for renewable energy. Comparing the effectiveness of our four patent counts, we find that both using only patents filed in multiple countries and weighting by family size improve the fit of the model.

New statistical methodology, mathematical models, and data bases relevant to the assessment of health impacts of energy technologies

International Nuclear Information System (INIS)

Ginevan, M.E.; Collins, J.J.; Brown, C.D.; Carnes, B.A.; Curtiss, J.B.; Devine, N.

1981-01-01

The present research develops new statistical methodology, mathematical models, and data bases of relevance to the assessment of health impacts of energy technologies, and uses these to identify, quantify, and pedict adverse health effects of energy related pollutants. Efforts are in five related areas including: (1) evaluation and development of statistical procedures for the analysis of death rate data, disease incidence data, and large scale data sets; (2) development of dose response and demographic models useful in the prediction of the health effects of energy technologies; (3) application of our method and models to analyses of the health risks of energy production; (4) a reanalysis of the Tri-State leukemia survey data, focusing on the relationship between myelogenous leukemia risk and diagnostic x-ray exposure; and (5) investigation of human birth weights as a possible early warning system for the effects of environmental pollution

Asia/Pacific Rim renewable energy market assessments by the State of Hawaii

International Nuclear Information System (INIS)

Ishimura, D.M.; Kinoshita, C.M.; Turn, S.Q.

1999-01-01

The State of Hawaii has begun to encourage its economic growth and diversification by increasing the export of U.S. energy, environment, ocean, and information technologies. Hawaii's Strategic Technology Market Assessment and Development (STMAD) program promotes the transfer of U.S. technology into Asia and the Pacific Rim, locations having phenomenal growth potential and vast technological infrastructure demands. The STMAD program is managed by the State's Department of Business, Economic Development and Tourism (DBEDT). Under the auspices of STMAD, the Hawaii Natural Energy Institute (HNEI) of the University of Hawaii is assessing biomass energy resources of Asian and Pacific Rim countries to identify and investigate sustainable energy markets. This paper reviews the STMAD program and reports findings of renewable energy assessment performed by HNEI and DBEDT. (author)

Environmental impacts from the solar energy technologies

International Nuclear Information System (INIS)

Tsoutsos, Theocharis; Frantzeskaki, Niki; Gekas, Vassilis

2005-01-01

Solar energy systems (photovoltaics, solar thermal, solar power) provide significant environmental benefits in comparison to the conventional energy sources, thus contributing, to the sustainable development of human activities. Sometimes however, their wide scale deployment has to face potential negative environmental implications. These potential problems seem to be a strong barrier for a further dissemination of these systems in some consumers. To cope with these problems this paper presents an overview of an Environmental Impact Assessment. We assess the potential environmental intrusions in order to ameliorate them with new technological innovations and good practices in the future power systems. The analysis provides the potential burdens to the environment, which include - during the construction, the installation and the demolition phases, as well as especially in the case of the central solar technologies - noise and visual intrusion, greenhouse gas emissions, water and soil pollution, energy consumption, labour accidents, impact on archaeological sites or on sensitive ecosystems, negative and positive socio-economic effects

Energy technologies at the cutting edge: international energy technology collaboration IEA Implementing Agreements

Energy Technology Data Exchange (ETDEWEB)

Pottinger, C. (ed.)

2007-05-15

Ensuring energy security and addressing climate change issues in a cost-effective way are the main challenges of energy policies and in the longer term will be solved only through technology cooperation. To encourage collaborative efforts to meet these energy challenges, the IEA created a legal contract - Implementing Agreement - and a system of standard rules and regulations. This allows interested member and non-member governments or other organisations to pool resources and to foster the research, development and deployment of particular technologies. For more than 30 years, this international technology collaboration has been a fundamental building block in facilitating progress of new or improved energy technologies. There are now 41 Implementing Agreements. This is the third in the series of publications highlighting the recent results and achievements of the IEA Implementing Agreements. This document is arranged in the following sections: Cross-cutting activities (sub-sectioned: Climate technology initiative; Energy Technology Data Eexchange; and Energy technology systems analysis programme); End-use technologies (sub-sectioned: Buildings; Electricity; Industry; and Transport; Fossil fuels (sub-sectioned: Clean Coal Centre; Enhanced oil recovery Fluidized bed conversion; Greenhouse Gas R & D; Multiphase flow sciences); Fusion power; Renewable energies and hydrogen; and For more information (including detail on the IEA energy technology network; IEA Secretariat Implementing Agreement support; and IEA framework. Addresses are given for the Implementing Agreements. The publication is based on core input from the Implementing Agreement Executive Committee.

Nordic energy technology scoreboard. Full version

Energy Technology Data Exchange (ETDEWEB)

Kiltkou, Antje; Iversen, Eric; Scortato, Lisa

2010-07-01

The Nordic Energy Technology Scoreboard provides a tool for understanding the state of low-carbon energy technology development in the Nordic region. It assesses the five Nordic countries of Denmark, Finland, Iceland, Norway and Sweden, alongside reference countries and regions including: The United Kingdom, Germany, Spain, Portugal, France, Italy, the Netherlands, Austria, USA, Japan and the EU 27. It focuses on five low-carbon energy technologies: Wind, photovoltaic (PV) solar, bio-fuels, geothermal, and carbon capture and storage (CCS). This scoreboard was developed as a pilot project with a limited scope of technologies, countries and indicators. In addition to providing a tool for decision-makers, it aimed to act as a catalyst for the future development of scoreboards and a vehicle to promote better data collection. Low-carbon energy technologies are not easy to measure. This is due to a variety of factors that much be kept in account when developing scoreboards for this purpose. Many low-carbon technologies are still at immature stages of development. Sound comparable data requires common definitions and standards to be adopted before collection can even take place. This process often lags behind the development of low-carbon technologies, and there are therefore considerable data availability and categorisation issues. The diversity of technologies and their different stages of development hamper comparability. The IEA classifies low-carbon technologies into three categories. The most mature includes hydropower, onshore wind, biomass CHP, and geothermal energy, the second most mature includes PV solar and offshore wind power, while the least mature includes concentrating solar power, CCS and ocean energy. This is problematic as less mature technologies are underrepresented in later stages of the innovation system. Many low-carbon technologies are systemic, meaning progress in developing one technology may hinge on developments in a connected technology

Technology Roadmap: Energy Storage

Energy Technology Data Exchange (ETDEWEB)

NONE

2014-03-01

Energy storage technologies are valuable components in most energy systems and could be an important tool in achieving a low-carbon future. These technologies allow for the decoupling of energy supply and demand, in essence providing a valuable resource to system operators. There are many cases where energy storage deployment is competitive or near-competitive in today's energy system. However, regulatory and market conditions are frequently ill-equipped to compensate storage for the suite of services that it can provide. Furthermore, some technologies are still too expensive relative to other competing technologies (e.g. flexible generation and new transmission lines in electricity systems). One of the key goals of this new roadmap is to understand and communicate the value of energy storage to energy system stakeholders. This will include concepts that address the current status of deployment and predicted evolution in the context of current and future energy system needs by using a ''systems perspective'' rather than looking at storage technologies in isolation.

Evaluating the impacts of energy supply technology options

International Nuclear Information System (INIS)

Peachey, B.R.

2009-01-01

The newly formed Chemical Institute of Canada (CIC)/Canadian Society for Chemical Engineering (CSChE) Energy Subject Division is working to develop a methodology for assessing and communicating to governments, regulators and the public the relative merits of different technologies for meeting energy demand requirements or reducing energy consumption. The focus is on developing a process that considers a broader range of issues than basic economics, or greenhouse gas (GHG) emissions. The 12 assessment criteria proposed would address five major areas of concerns including: a) how well assumptions have been tested against the scientific method over the life cycle of an energy development, b) impacts on the availability of the basic requirements for life, c) maintaining the quality of human life, d) maintaining the quality of the local environment (air, land and water), in the area where a specific technology is used, and e) considers the potential global impacts of GHG emissions. (author)

Energy technology perspectives: scenarios and strategies to 2050 [Russian version

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

At their 2005 summit in Gleneagles, G8 leaders confronted questions of energy security and supply and lowering of CO{sub 2} emissions and decided to act with resolve and urgency. They called upon the International Energy Agency to provide advice on scenarios and strategies for a clean and secure energy future. Energy Technology Perspectives is a response to the G8 request. This work demonstrates how energy technologies can make a difference in a series of global scenarios to 2050. It reviews in detail the status and prospects of key energy technologies in electricity generation, buildings, industry and transport. It assesses ways the world can enhance energy security and contain growth in CO{sub 2} emissions by using a portfolio of current and emerging technologies. Major strategic elements of a successful portfolio are energy efficiency, CO{sub 2} capture and storage, renewables and nuclear power. 110 figs., 4 annexes.

Stakeholders’ influence on the adoption of energy-saving technologies in Italian homes

International Nuclear Information System (INIS)

Berardi, Umberto

2013-01-01

The instability and fragmentation of the temporary aggregations of many stakeholders in construction processes are barriers to adopting new technologies. This paper investigates the influence of different stakeholders on the adoption of mature energy-saving technologies in new residential buildings. Recent literature about the influence of different stakeholders on construction processes is reviewed focusing in their interest for energy saving technologies. To gain an insight into the specific roles played by stakeholders (general contractors, construction firms, architects, users and public governments) in different projects, a case study methodology was used. The influence on the adoption of energy-saving technologies of stakeholders was assessed through semi-structured interviews. These interviews focused on the interest and power for the adoption of several energy-saving technologies. Having recognized that the interest in adoption is often expressed late in the construction processes, the time of introduction of this interest was assessed. This paper provides an empirical insight into significant barriers for the adoption of energy saving technologies which are the low influence of highly motivated stakeholders on the decision of adoption, and the delay at which the interest in energy-saving technologies emerges. Finally, policies to overcome these barriers are suggested. - Highlights: • Why energy saving technologies are rarely adopted in buildings? • Diffusion is slowed by the late participation of stakeholders with great interest for energy technologies. • The influence of construction stakeholders for the adoption of energy saving technologies is measured in Italian case studies. • More integrated relationships among stakeholders are required to help the adoption of energy saving technologies. • Process re-organizations and policies which increase final users’ power are needed

Predicting technology operational availability using technical maturity assessment

International Nuclear Information System (INIS)

Kenley, C.R.; Creque, T.R.

1998-01-01

A technical maturity assessment method was performed by systems engineers in collaboration with an advisory panel composed of team members from different Department of Energy sites and from different engineering and science disciplines. Various stabilization technologies were assessed annually as to their relative maturity and availability for use in stabilizing nuclear materials. After three years of assessments, several of the technologies are now components of operational systems. A regression analysis of the historical assessments was performed, and it was concluded that the numerical technical maturity score produced by a team of experts can provide a powerful predictor of the time remaining until the operational application of technologies

Life cycle assessment of innovative technology for energy production from automotive shredder residue.

Science.gov (United States)

Rinaldi, Caterina; Masoni, Paolo; Salvati, Fabio; Tolve, Pietro

2015-07-01

Automotive Shredder Residue (ASR) is a problematic waste material remaining after shredding and recovery processes of end-of-life vehicles (ELVs). Its heterogeneous grain size and composition make difficult its recovery or disposal. Although ASR accounts for approximately 20% to 25% of the weight of an ELV, the European Union (EU)'s ELV Directive (2000/53/EC) requires that by 2015 a minimum 95% of the weight of an ELV must be reused or recovered, including a 10% weight energy recovery. The quantity of ASR is relevant: Approximately 2.4 million tons are generated in the EU each year and most of it is sent to landfills. This article describes a life cycle model of the "TEKNE-Fluff" process designed to make beneficial use of ASR that is based on the results of an experimental pilot plant for pyro-gasification, combustion, cogeneration, and emissions treatment of ASR. The goal of the research was the application of life cycle assessment (LCA) methodology to identify the environmental hot spots of the "TEKNE system" and use scenario analysis to check solutions to improve its environmental profile, supporting the design and industrialization process. The LCA was conducted based on data modeled from the experimental campaign. Moreover, different scenarios on shares of electricity and thermal energy produced by the cogeneration system and alternative treatment processes for the waste produced by the technology were compared. Despite the limitation of the research (results based on scaling up experimental data by modeling), impact assessment results are promising and sufficiently robust, as shown by Monte Carlo analysis. The TEKNE technology may become an interesting solution for the problem of ASR management: Besides representing an alternative to landfill disposal, the energy produced could avoid significant impacts on fossil resources depletion (a plant of 40,000 tons/y capacity could produce ∼ 147,000 GJ/yr, covering the annual need of ∼ 13,500 households). © 2015

Energy technology evaluation report: Energy security

Science.gov (United States)

Koopman, R.; Lamont, A.; Schock, R.

1992-09-01

Energy security was identified in the National Energy Strategy (NES) as a major issue for the Department of Energy (DOE). As part of a process designed by the DOE to identify technologies important to implementing the NES, an expert working group was convened to consider which technologies can best contribute to reducing the nation's economic vulnerability to future disruptions of world oil supplies, the working definition of energy security. Other working groups were established to deal with economic growth, environmental quality, and technical foundations. Energy Security working group members were chosen to represent as broad a spectrum of energy supply and end-use technologies as possible and were selected for their established reputations as experienced experts with an ability to be objective. The time available for this evaluation was very short. The group evaluated technologies using criteria taken from the NES which can be summarized for energy security as follows: diversifying sources of world oil supply so as to decrease the increasing monopoly status of the Persian Gulf region; reducing the importance of oil use in the US economy to diminish the impact of future disruptions in oil supply; and increasing the preparedness of the US to deal with oil supply disruptions by having alternatives available at a known price. The result of the first phase of the evaluation process was the identification of technology groups determined to be clearly important for reducing US vulnerability to oil supply disruptions. The important technologies were mostly within the high leverage areas of oil and gas supply and transportation demand but also included hydrogen utilization, biomass, diversion resistant nuclear power, and substitute industrial feedstocks.

Renewable energy technologies and the European industry

International Nuclear Information System (INIS)

Whiteley, M.; Bess, M.

2000-01-01

The European renewable energy industry has the potential to be a world leader. This has been achieved within the European region for specific technologies, through a set of policy activities at a national and regional level, driven primarily by employment, energy self-sufficiency and industrial competitiveness. Using the experience gained in recent years, European industry has the opportunity to continue to expand its horizons on a worldwide level. Through the use of the SAFIRE rational energy model, an assessment has been made of the future penetration of renewable energy within Europe and the effects on these socio-economic factors. In conjunction with these outputs, assessments of the worldwide markets for wind, photovoltaics, solar thermal plant and biomass have been assessed. A case study of the Danish wind industry is used as a prime example of a success story from which the learning opportunities are replicated to other industries, so that the European renewable energy industry can achieve its potential. (orig.)

Life cycle emissions from renewable energy technologies

International Nuclear Information System (INIS)

Bates, J.; Watkiss, P.; Thorpe, T.

1997-01-01

This paper presents the methodology used in the ETSU review, together with the detailed results for three of the technologies studied: wind turbines, photovoltaic systems and small, stand-alone solar thermal systems. These emissions are then compared with those calculated for both other renewables and fossil fuel technology on a similar life cycle basis. The life cycle emissions associated with renewable energy technology vary considerably. They are lowest for those technologies where the renewable resource has been concentrated in some way (e.g. over distance in the case of wind and hydro, or over time in the case of energy crops). Wind turbines have amongst the lowest emissions of all renewables and are lower than those for fossil fuel generation, often by over an order of magnitude. Photovoltaics and solar thermal systems have the highest life cycle emissions of all the renewable energy technologies under review. However, their emissions of most pollutants are also much lower than those associated with fossil fuel technologies. In addition, the emissions associated with PV are likely to fall further in the future as the conversion efficiency of PV cells increases and manufacturing technology switches to thin film technologies, which are less energy intensive. Combining the assessments of life cycle emissions of renewables with predictions made by the World Energy Council (WEC) of their future deployment has allowed estimates to be made of amount by which renewables could reduce the future global emissions of carbon dioxide, sulphur dioxide and nitrogen oxides. It estimated that under the WEC's 'Ecologically Driven' scenario, renewables might lead to significant reductions of between 3650 and 8375 Mt in annual CO 2 emissions depending on the fossil fuel technology they are assumed to displace. (author)

Assessment of a closed thermochemical energy storage using energy and exergy methods

International Nuclear Information System (INIS)

Abedin, Ali Haji; Rosen, Marc A.

2012-01-01

Highlights: ► Thermodynamics assessments are reported for a general closed thermochemical thermal energy storage system. ► Energy and exergy efficiencies of various processes in a closed thermochemical TES are evaluated and compared. ► Understanding is enhanced of thermochemical TES technologies and their potential implementations. ► Exergy analysis is observed to be useful when applied to thermochemical TES, with or in place of energy analysis. - Abstract: Thermal energy storage (TES) is an important technology for achieving more efficient and environmentally benign energy systems. Thermochemical TES is a type of TES with the potential for high energy density and is only recently being considered intensively. To improve understanding of thermochemical TES systems and their implementation, energy and exergy analyses are beneficial. Here, thermodynamics assessments are presented for a general closed thermochemical TES system, including assessments and comparisons of the efficiencies of the overall thermochemical TES cycle and its charging, storing and discharging processes. Locations and causes of thermodynamic losses in thermochemical TES systems are being specified using exergy analysis. The analytical methodology applied in this study identifies that energy and exergy efficiencies differ for thermochemical TESs, e.g. the energy efficiency for a case study is approximately 50% while the exergy efficiency is about 10%. Although the focus is to evaluate thermodynamic efficiencies, other design parameters such as cost, and environmental impact also need to be examined in assessing thermochemical storage. The efficiencies for thermochemical TES provided here should be helpful for designing these energy systems and enhancing their future prospects.

Long-term affected energy production of waste to energy technologies identified by use of energy system analysis.

Science.gov (United States)

Münster, M; Meibom, P

2010-12-01

Affected energy production is often decisive for the outcome of consequential life-cycle assessments when comparing the potential environmental impact of products or services. Affected energy production is however difficult to determine. In this article the future long-term affected energy production is identified by use of energy system analysis. The focus is on different uses of waste for energy production. The Waste-to-Energy technologies analysed include co-combustion of coal and waste, anaerobic digestion and thermal gasification. The analysis is based on optimization of both investments and production of electricity, district heating and bio-fuel in a future possible energy system in 2025 in the countries of the Northern European electricity market (Denmark, Norway, Sweden, Finland and Germany). Scenarios with different CO(2) quota costs are analysed. It is demonstrated that the waste incineration continues to treat the largest amount of waste. Investments in new waste incineration capacity may, however, be superseded by investments in new Waste-to-Energy technologies, particularly those utilising sorted fractions such as organic waste and refuse derived fuel. The changed use of waste proves to always affect a combination of technologies. What is affected varies among the different Waste-to-Energy technologies and is furthermore dependent on the CO(2) quota costs and on the geographical scope. The necessity for investments in flexibility measures varies with the different technologies such as storage of heat and waste as well as expansion of district heating networks. Finally, inflexible technologies such as nuclear power plants are shown to be affected. Copyright © 2010 Elsevier Ltd. All rights reserved.

Sustainability assessment of renewable power and heat generation technologies

International Nuclear Information System (INIS)

Dombi, Mihály; Kuti, István; Balogh, Péter

2014-01-01

Rationalisation of consumption, more efficient energy usage and a new energy structure are needed to be achieved in order to shift the structure of energy system towards sustainability. The required energy system is among others characterised by intensive utilisation of renewable energy sources (RES). RES technologies have their own advantages and disadvantages. Nevertheless, for the strategic planning there is a great demand for the comparison of RES technologies. Furthermore, there are additional functions of RES utilisation expected beyond climate change mitigation, e.g. increment of employment, economic growth and rural development. The aim of the study was to reveal the most beneficial RES technologies with special respect to sustainability. Ten technologies of power generation and seven technologies of heat supply were examined in a multi-criteria sustainability assessment frame of seven attributes which were evaluated based on a choice experiment (CE) survey. According to experts the most important characteristics of RES utilisation technologies are land demand and social impacts i.e. increase in employment and local income generation. Concentrated solar power (CSP), hydropower and geothermal power plants are favourable technologies for power generation, while geothermal district heating, pellet-based non-grid heating and solar thermal heating can offer significant advantages in case of heat supply. - highlights: • We used choice experiment to estimate the weights of criteria for the sustainability assessment of RES technologies. • The most important attributes of RES technologies according to experts are land demand and social impacts. • Concentrated solar power (CSP), hydropower and geothermal power plants are advantageous technologies for power generation. • Geothermal district heating, pellet-based non-grid heating and solar thermal heating are favourable in case of heat supply

Finnish energy technology programmes 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

The Finnish Technology Development Centre (Tekes) is responsible for the financing of research and development in the field of energy production technology. A considerable part of the financing goes to technology programmes. Each technology programme involves major Finnish institutions - companies, research institutes, universities and other relevant interests. Many of the energy technology programmes running in 1998 were launched collectively in 1993 and will be completed at the end of 1998. They are complemented by a number of other energy-related technology programmes, each with a timetable of its own. Because energy production technology is horizontal by nature, it is closely connected with research and development in other fields, too, and is an important aspect in several other Tekes technology programmes. For this reason this brochure also presents technology programmes where energy is only one of the aspects considered but which nevertheless contribute considerably to research and development in the energy production sector

New energy technologies. Report; Nouvelles technologies de l'energie. Rapport

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This report on the new energy technologies has been written by a working group on request of the French ministry of economy, finances and industry, of the ministry of ecology and sustainable development, of the ministry of research and new technologies and of the ministry of industry. The mission of the working group is to identify goals and priority ways for the French and European research about the new technologies of energy and to propose some recommendations about the evolution of research incentive and sustain systems in order to reach these goals. The working group has taken into consideration the overall stakes linked with energy and not only the climatic change. About this last point, only the carbon dioxide emissions have been considered because they represent 90% of the greenhouse gases emissions linked with the energy sector. A diagnosis is made first about the present day context inside which the new technologies will have to fit with. Using this diagnosis, the research topics and projects to be considered as priorities for the short-, medium- and long-term have been identified: energy efficiency in transports, in dwellings/tertiary buildings and in the industry, development for the first half of the 21. century of an energy mix combining nuclear, fossil-fuels and renewable energy sources. (J.S.)

Assessment of the greenhouse effect impact of technologies used for energy recovery from municipal waste: a case for England.

Science.gov (United States)

Papageorgiou, A; Barton, J R; Karagiannidis, A

2009-07-01

Waste management activities contribute to global greenhouse gas emissions approximately by 4%. In particular the disposal of waste in landfills generates methane that has high global warming potential. Effective mitigation of greenhouse gas emissions is important and could provide environmental benefits and sustainable development, as well as reduce adverse impacts on public health. The European and UK waste policy force sustainable waste management and especially diversion from landfill, through reduction, reuse, recycling and composting, and recovery of value from waste. Energy from waste is a waste management option that could provide diversion from landfill and at the same time save a significant amount of greenhouse gas emissions, since it recovers energy from waste which usually replaces an equivalent amount of energy generated from fossil fuels. Energy from waste is a wide definition and includes technologies such as incineration of waste with energy recovery, or combustion of waste-derived fuels for energy production or advanced thermal treatment of waste with technologies such as gasification and pyrolysis, with energy recovery. The present study assessed the greenhouse gas emission impacts of three technologies that could be used for the treatment of Municipal Solid Waste in order to recover energy from it. These technologies are Mass Burn Incineration with energy recovery, Mechanical Biological Treatment via bio-drying and Mechanical Heat Treatment, which is a relatively new and uninvestigated method, compared to the other two. Mechanical Biological Treatment and Mechanical Heat Treatment can turn Municipal Solid Waste into Solid Recovered Fuel that could be combusted for energy production or replace other fuels in various industrial processes. The analysis showed that performance of these two technologies depends strongly on the final use of the produced fuel and they could produce GHG emissions savings only when there is end market for the fuel. On the

Environmental & economic life cycle assessment of current & future sewage sludge to energy technologies.

Science.gov (United States)

Mills, N; Pearce, P; Farrow, J; Thorpe, R B; Kirkby, N F

2014-01-01

The UK Water Industry currently generates approximately 800GWh pa of electrical energy from sewage sludge. Traditionally energy recovery from sewage sludge features Anaerobic Digestion (AD) with biogas utilisation in combined heat and power (CHP) systems. However, the industry is evolving and a number of developments that extract more energy from sludge are either being implemented or are nearing full scale demonstration. This study compared five technology configurations: 1 - conventional AD with CHP, 2 - Thermal Hydrolysis Process (THP) AD with CHP, 3 - THP AD with bio-methane grid injection, 4 - THP AD with CHP followed by drying of digested sludge for solid fuel production, 5 - THP AD followed by drying, pyrolysis of the digested sludge and use of the both the biogas and the pyrolysis gas in a CHP. The economic and environmental Life Cycle Assessment (LCA) found that both the post AD drying options performed well but the option used to create a solid fuel to displace coal (configuration 4) was the most sustainable solution economically and environmentally, closely followed by the pyrolysis configuration (5). Application of THP improves the financial and environmental performance compared with conventional AD. Producing bio-methane for grid injection (configuration 3) is attractive financially but has the worst environmental impact of all the scenarios, suggesting that the current UK financial incentive policy for bio-methane is not driving best environmental practice. It is clear that new and improving processes and technologies are enabling significant opportunities for further energy recovery from sludge; LCA provides tools for determining the best overall options for particular situations and allows innovation resources and investment to be focused accordingly. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Renewable, ethical? Assessing the energy justice potential of renewable electricity

Directory of Open Access Journals (Sweden)

Aparajita Banerjee

2017-08-01

Full Text Available Energy justice is increasingly being used as a framework to conceptualize the impacts of energy decision making in more holistic ways and to consider the social implications in terms of existing ethical values. Similarly, renewable energy technologies are increasingly being promoted for their environmental and social benefits. However, little work has been done to systematically examine the extent to which, in what ways and in what contexts, renewable energy technologies can contribute to achieving energy justice. This paper assesses the potential of renewable electricity technologies to address energy justice in various global contexts via a systematic review of existing studies analyzed in terms of the principles and dimensions of energy justice. Based on publications including peer reviewed academic literature, books, and in some cases reports by government or international organizations, we assess renewable electricity technologies in both grid integrated and off-grid use contexts. We conduct our investigation through the rubric of the affirmative and prohibitive principles of energy justice and in terms of its temporal, geographic, socio-political, economic, and technological dimensions. Renewable electricity technology development has and continue to have different impacts in different social contexts, and by considering the different impacts explicitly across global contexts, including differences between rural and urban contexts, this paper contributes to identifying and understanding how, in what ways, and in what particular conditions and circumstances renewable electricity technologies may correspond with or work to promote energy justice.

Methods of Comprehensive Assessment for China’s Energy Sustainability

Science.gov (United States)

Xu, Zhijin; Song, Yankui

2018-02-01

In order to assess the sustainable development of China’s energy objectively and accurately, we need to establish a reasonable indicator system for energy sustainability and make a targeted comprehensive assessment with the scientific methods. This paper constructs a comprehensive indicator system for energy sustainability from five aspects of economy, society, environment, energy resources and energy technology based on the theory of sustainable development and the theory of symbiosis. On this basis, it establishes and discusses the assessment models and the general assessment methods for energy sustainability with the help of fuzzy mathematics. It is of some reference for promoting the sustainable development of China’s energy, economy and society.

A fuzzy levelised energy cost method for renewable energy technology assessment

International Nuclear Information System (INIS)

Wright, Daniel G.; Dey, Prasanta K.; Brammer, John G.

2013-01-01

Renewable energy project development is highly complex and success is by no means guaranteed. Decisions are often made with approximate or uncertain information yet the current methods employed by decision-makers do not necessarily accommodate this. Levelised energy costs (LEC) are one such commonly applied measure utilised within the energy industry to assess the viability of potential projects and inform policy. The research proposes a method for achieving this by enhancing the traditional discounting LEC measure with fuzzy set theory. Furthermore, the research develops the fuzzy LEC (F-LEC) methodology to incorporate the cost of financing a project from debt and equity sources. Applied to an example bioenergy project, the research demonstrates the benefit of incorporating fuzziness for project viability, optimal capital structure and key variable sensitivity analysis decision-making. The proposed method contributes by incorporating uncertain and approximate information to the widely utilised LEC measure and by being applicable to a wide range of energy project viability decisions. -- Highlights: •Proposes a fuzzy levelised energy cost (F-LEC) methodology to support energy project development. •Incorporates the terms and cost of project finance into the F-LEC method. •Applies the F-LEC method to an example bioenergy project development case

Potential Offshore Wind Energy Areas in California: An Assessment of Locations, Technology, and Costs

Energy Technology Data Exchange (ETDEWEB)

Musial, Walter [National Renewable Energy Lab. (NREL), Golden, CO (United States); Beiter, Philipp [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tegen, Suzanne [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, Aaron [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-12-01

This report summarizes a study of possible offshore wind energy locations, technologies, and levelized cost of energy in the state of California between 2015 and 2030. The study was funded by the U.S. Department of the Interior's Bureau of Ocean Energy Management (BOEM), the federal agency responsible for regulating renewable energy development on the Outer Continental Shelf. It is based on reference wind energy areas where representative technology and performance characteristics were evaluated. These reference areas were identified as sites that were suitable to represent offshore wind cost and technology based on physical site conditions, wind resource quality, known existing site use, and proximity to necessary infrastructure. The purpose of this study is to assist energy policy decision-making by state utilities, independent system operators, state government officials and policymakers, BOEM, and its key stakeholders. The report is not intended to serve as a prescreening exercise for possible future offshore wind development.

New energy technologies 4. Energy management and energy efficiency

International Nuclear Information System (INIS)

Sabonnadiere, J.C.; Caire, R.; Raison, B.; Quenard, D.; Verneau, G.; Zissis, G.

2007-01-01

This forth tome of the new energy technologies handbook is devoted to energy management and to the improvement of energy efficiency. The energy management by decentralized generation insertion and network-driven load control, analyzes the insertion and management means of small power generation in distribution networks and the means for load management by the network with the aim of saving energy and limiting peak loads. The second part, devoted to energy efficiency presents in a detailed way the technologies allowing an optimal management of energy in buildings and leading to the implementation of positive energy buildings. A special chapter treats of energy saving using new lighting technologies in the private and public sectors. Content: 1 - decentralized power generation - impacts and solutions: threat or opportunity; deregulation; emerging generation means; impact of decentralized generation on power networks; elements of solution; 2 - mastery of energy demand - loads control by the network: stakes of loads control; choice of loads to be controlled; communication needs; measurements and controls for loads control; model and algorithm needs for loads control. A better energy efficiency: 3 - towards positive energy buildings: key data for Europe; how to convert fossil energy consuming buildings into low-energy consuming and even energy generating buildings; the Minergie brand; the PassivHaus or 'passive house' label; the zero-energy house/zero-energy home (ZEH); the zero-energy building (ZEB); the positive energy house; comparison between the three Minergie/PassivHaus/ZEH types of houses; beyond the positive energy building; 4 - light sources and lighting systems - from technology to energy saving: lighting yesterday and today; light sources and energy conversion; energy saving in the domain of lighting: study of some type-cases; what future for light sources. (J.S.)

Risoe energy report 1. New and emerging technologies - options for the future

International Nuclear Information System (INIS)

Larsen, H.; Soenderberg Petersen, L.

2002-10-01

All over the world, increasing energy consumption, liberalisation of energy markets and the need to take action on climate change are producing new challenges for the energy sector. At the same time there is increasing pressure for research, new technology and industrial products to be socially acceptable and to generate prosperity. The result is a complex and dynamic set of conditions affecting decisions on investment in research and new energy technology. To meet these challenges in the decades ahead, industrialists and policymakers need appropriate analyse energy systems, plus knowledge of trends for existing technologies and prospects for emerging technologies. This is the background for this first Risoe Energy Report, which sets out the global, European and Danish energy scene together with trends in development and emerging technologies. The report is the first in a new series from Risoe National Laboratory. The global energy developments are presented based on the latest available information from authoritative sources like IEA, WEC, World Energy Assessment etc. Some of the major challenges are presented in terms of the changing energy markets in all regions, the focus on environmental concerns in the industrialised countries, and energy for development and access to energy for the poor in developing countries. The report presents the status of R and D in progress for supply technologies. The various technologies are assessed with respect to status, trends and perspectives for the technology, and international R and D plans. For the technologies where Risoe is undertaking R and D this is highlighted in a separate section. Recent studies of emerging energy technologies from international organisations and leading research organisations are reviewed. There are reviews of national research activities on new energy technologies in a number of countries as well as in Risoe National Laboratory. Conclusions for Danish energy supply, Danish industry, and Danish

Technological and life cycle assessment of organics processing odour control technologies

Energy Technology Data Exchange (ETDEWEB)

Bindra, Navin [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Dubey, Brajesh, E-mail: bkdubey@civil.iitkgp.ernet.in [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Environmental Engineering Division, Department of Civil Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Dutta, Animesh [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada)

2015-09-15

As more municipalities and communities across developed world look towards implementing organic waste management programmes or upgrading existing ones, composting facilities are emerging as a popular choice. However, odour from these facilities continues to be one of the most important concerns in terms of cost & effective mitigation. This paper provides a technological and life cycle assessment of some of the different odour control technologies and treatment methods that can be implemented in organics processing facilities. The technological assessment compared biofilters, packed tower wet scrubbers, fine mist wet scrubbers, activated carbon adsorption, thermal oxidization, oxidization chemicals and masking agents. The technologies/treatment methods were evaluated and compared based on a variety of operational, usage and cost parameters. Based on the technological assessment it was found that, biofilters and packed bed wet scrubbers are the most applicable odour control technologies for use in organics processing faculties. A life cycle assessment was then done to compare the environmental impacts of the packed-bed wet scrubber system, organic (wood-chip media) bio-filter and inorganic (synthetic media) bio-filter systems. Twelve impact categories were assessed; cumulative energy demand (CED), climate change, human toxicity, photochemical oxidant formation, metal depletion, fossil depletion, terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial eco-toxicity, freshwater eco-toxicity and marine eco-toxicity. The results showed that for all impact categories the synthetic media biofilter had the highest environmental impact, followed by the wood chip media bio-filter system. The packed-bed system had the lowest environmental impact for all categories. - Highlights: • Assessment of odour control technologies for organics processing facilities. • Comparative life cycle assessment of three odour control technologies was conducted

Energy Policy is Technology Politics The Hydrogen Energy Case

International Nuclear Information System (INIS)

Carl-Jochen Winter

2006-01-01

Germany's energy supply status shows both an accumulation of unsatisfactory sustainabilities putting the nation's energy security at risk, and a hopeful sign: The nation's supply dependency on foreign sources and the accordingly unavoidable price dictate the nation suffers under is almost life risking; the technological skill, however, of the nation's researchers, engineers, and industry materializes in a good percentage of the indigenous and the world's energy conversion technology market. Exemplified with the up and coming hydrogen energy economy this paper tries to advocate the 21. century energy credo: energy policy is energy technology politics! Energy source thinking and acting is 19. and 20. century, energy efficient conversion technology thinking and acting is 21. century. Hydrogen energy is on the verge of becoming the centre-field of world energy interest. Hydrogen energy is key for the de-carbonization and, thus, sustainabilization of fossil fuels, and as a storage and transport means for the introduction of so far un-operational huge renewable sources into the world energy market. - What is most important is hydrogen's thermodynamic ability to exergize the energy scheme: hydrogen makes more technical work (exergy) out of less primary energy! Hydrogen adds value. Hydrogen energy and, in particular, hydrogen energy technologies, are to become part of Germany's national energy identity; accordingly, national energy policy as energy technology politics needs to grow in the nation's awareness as common sense! Otherwise Germany seems ill-equipped energetically, and its well-being hangs in the balance. (author)

Materials, critical materials and clean-energy technologies

Science.gov (United States)

Eggert, R.

2017-07-01

Modern engineered materials, components and systems depend on raw materials whose properties provide essential functionality to these technologies. Some of these raw materials are subject to supply-chain risks, and such materials are known as critical materials. This paper reviews corporate, national and world perspectives on material criticality. It then narrows its focus to studies that assess "what is critical" to clean-energy technologies. The focus on supply-chain risks is not meant to be alarmist but rather to encourage attention to monitoring these risks and pursuing technological innovation to mitigate the risks.

The role of scientific knowledge in the public's perceptions of energy technology risks

International Nuclear Information System (INIS)

Stoutenborough, James W.; Vedlitz, Arnold

2016-01-01

It is important for policy makers to have an accurate understanding of public attitudes toward pressing issues to help inform their decision making. Researchers consistently find that the public’s receipt of and correct processing of scientific information and knowledge are essential for its problem solving. Different levels of understanding of specific energy technologies may produce different risk assessments across technologies within this issue domain. How this differential risk assessment occurs and the role that scientific information may play in it is not yet well known. This project seeks to determine the role that perceived and objective scientific knowledge may play in the public’s risk assessments of different energy technologies. Our findings suggest that scientific knowledge does temper public risk evaluations of different energy technologies, therefore linking more clearly the connection between science knowledge, scientific trust, and issue problem identification. - Highlights: •We examine influence of assessed and perceived knowledge on public risk perceptions. •We model effect of knowledge type on publics’ perceptions of three energy risks. •All models show those with higher assessed knowledge see risks more like experts do. •Perceived knowledge is less reliable predictor of public rating risk like experts. •Greater scientific grasp of issues by public needed for accurate risk assessment.

How methodological issues affect the energy indicator results for different electricity generation technologies

International Nuclear Information System (INIS)

Modahl, Ingunn Saur; Raadal, Hanne Lerche; Gagnon, Luc; Bakken, Tor Haakon

2013-01-01

The aim of this paper is to improve the basis for the comparison of energy products. The paper will discuss important methodological issues with regard to various energy indicators and it will, by means of a few selected energy indicators, show examples of results for hydropower, wind power and electricity from biomass, gas and coal. Lastly it will suggest methods to achieve results which are more consistent when comparing electricity production technologies. In general, methodological issues can affect the results of life cycle assessments. In this paper, the authors have focused on the effect of system boundaries for energy indicators and found that the internal ranking of cases within one electricity generation technology is dependent on the indicator used. These variations do not, however, alter the general ranking of the major technologies studied. The authors suggest that future assessments should focus on a smaller set of indicators: the Cumulative Energy Demand (CED), which is the most “universal” indicator, Energy Payback Ratio (EPR) for assessment of upstream activities, and a suggested “Cumulative Fossil Energy Demand” (CFED) for resource depletion assessments. There is also a need for stricter standardisation and increased transparency in the assessment of energy products. - Highlights: • There is a need for stricter standardisation of energy performance assessments. • System boundaries for renewable sources should be harmonised. • One should focus on a smaller set of indicators. CED should be included

Environmental consequences of new energy technology

International Nuclear Information System (INIS)

Svensson, Torbjoern

1991-09-01

This report summarises and assesses the environmental consequences associated with new energy technologies, with particular emphasis on their use for space heating supplies in the built environment. In the case of solar heating, it is primarily the processes associated with the production of the necessary materials and ground use requirements that can adversely affect the environment. There is also a certain risk associated with the leakage of heat transfer fluid. For heat stores, problem areas are primarily those associated with heating of the ground, discharge of foreign substances in connection with water treatment and conflicts of other users of ground water. The main adverse effects of heat pumps are their emissions of CFCs, which damage the ozone layer, utilisation of certain types of heat sources and the need to provide primary energy for mechanical drive of the pumps. All three of these new energy technologies are regarded as having less environmental consequences than conventional alternatives, although this assumes a change to less hazardous working media in heat pumps. A mutual comparison of the three technologies indicates that solar heating and heat stores have somewhat better environmental characteristics than heat pumps

Key energy technologies for Europe

Energy Technology Data Exchange (ETDEWEB)

Holst Joergensen, Birte

2005-09-01

The report is part of the work undertaken by the High-Level Expert Group to prepare a report on emerging science and technology trends and the implications for EU and Member State research policies. The outline of the report is: 1) In the introductory section, energy technologies are defined and for analytical reasons further narrowed down; 2) The description of the socio-economic challenges facing Europe in the energy field is based on the analysis made by the International Energy Agency going back to 1970 and with forecasts to 2030. Both the world situation and the European situation are described. This section also contains an overview of the main EU policy responses to energy. Both EU energy R and D as well as Member State energy R and D resources are described in view of international efforts; 3) The description of the science and technology base is made for selected energy technologies, including energy efficiency, biomass, hydrogen, and fuel cells, photovoltaics, clean fossil fuel technologies and CO{sub 2} capture and storage, nuclear fission and fusion. When possible, a SWOT is made for each technology and finally summarised; 4) The forward look highlights some of the key problems and uncertainties related to the future energy situation. Examples of recent energy foresights are given, including national energy foresights in Sweden and the UK as well as links to a number of regional and national foresights and roadmaps; 5) Appendix 1 contains a short description of key international organisations dealing with energy technologies and energy research. (ln)

Key energy technologies for Europe

International Nuclear Information System (INIS)

Holst Joergensen, Birte

2005-09-01

The report is part of the work undertaken by the High-Level Expert Group to prepare a report on emerging science and technology trends and the implications for EU and Member State research policies. The outline of the report is: 1) In the introductory section, energy technologies are defined and for analytical reasons further narrowed down; 2) The description of the socio-economic challenges facing Europe in the energy field is based on the analysis made by the International Energy Agency going back to 1970 and with forecasts to 2030. Both the world situation and the European situation are described. This section also contains an overview of the main EU policy responses to energy. Both EU energy R and D as well as Member State energy R and D resources are described in view of international efforts; 3) The description of the science and technology base is made for selected energy technologies, including energy efficiency, biomass, hydrogen, and fuel cells, photovoltaics, clean fossil fuel technologies and CO 2 capture and storage, nuclear fission and fusion. When possible, a SWOT is made for each technology and finally summarised; 4) The forward look highlights some of the key problems and uncertainties related to the future energy situation. Examples of recent energy foresights are given, including national energy foresights in Sweden and the UK as well as links to a number of regional and national foresights and roadmaps; 5) Appendix 1 contains a short description of key international organisations dealing with energy technologies and energy research. (ln)

Dynamics of energy systems: Methods of analysing technology change

Energy Technology Data Exchange (ETDEWEB)

Neij, Lena

1999-05-01

Technology change will have a central role in achieving a sustainable energy system. This calls for methods of analysing the dynamics of energy systems in view of technology change and policy instruments for effecting and accelerating technology change. In this thesis, such methods have been developed, applied, and assessed. Two types of methods have been considered, methods of analysing and projecting the dynamics of future technology change and methods of evaluating policy instruments effecting technology change, i.e. market transformation programmes. Two methods are focused on analysing the dynamics of future technology change; vintage models and experience curves. Vintage models, which allow for complex analysis of annual streams of energy and technological investments, are applied to the analysis of the time dynamics of electricity demand for lighting and air-distribution in Sweden. The results of the analyses show that the Swedish electricity demand for these purposes could decrease over time, relative to a reference scenario, if policy instruments are used. Experience curves are used to provide insight into the prospects of diffusion of wind turbines and photo voltaic (PV) modules due to cost reduction. The results show potential for considerable cost reduction for wind-generated electricity, which, in turn, could lead to major diffusion of wind turbines. The results also show that major diffusion of PV modules, and a reduction of PV generated electricity down to the level of conventional base-load electricity, will depend on large investments in bringing the costs down (through R D and D, market incentives and investments in niche markets) or the introduction of new generations of PV modules (e.g. high-efficiency mass-produced thin-film cells). Moreover, a model has been developed for the evaluation of market transformation programmes, i.e. policy instruments that effect technology change and the introduction and commercialisation of energy

Improving tag/seal technologies: the vulnerability assessment component

International Nuclear Information System (INIS)

Jones, J.L.

1996-01-01

The Department of Energy (DOE), specifically the Office of Nonproliferation and National Security, has sponsored the development of numerous tag and seal technologies for high-security/high-valued applications. One important component in this technology development effort has been the continuous integration of vulnerability assessments. The Idaho National Engineering Laboratory (INEL) has been the lead laboratory for vulnerability assessments of fiber-optic-based tag/seal technologies. This paper presents a brief historical overview and the current status of the DOE high-security tag/seal development program and discusses INEL's adversarial role and assessment philosophy. Verification testing criteria used to define ''successful'' tampering attempts/attacks are discussed. Finally, the advantages of integrating a vulnerability assessment into the development of commercial security tag/seals are presented

Energy efficiency assessment methods and tools evaluation. Bolling Air Force Base. Revision 1

Energy Technology Data Exchange (ETDEWEB)

McMordie, K.L.; Richman, E.E.; Keller, J.M.; Dixon, D.R.

1995-05-01

The goal of the U.S. Department of Energy (DOE) Federal Energy Management Program (FEMP) is to facilitate energy-efficiency improvements at federal facilities. This is accomplished by a balanced program of technology development, facility assessment, and use of cost-sharing procurement mechanisms. Technology development focuses upon the tools, software, and procedures used to identify and evaluate energy-efficiency technologies and improvements. For facility assessment, FEMP provides metering equipment and trained analysts to federal agencies exhibiting a commitment to improve energy use efficiency. To assist in procurement of energy-efficiency measures, FEMP helps federal agencies devise and implement performance contracting and utility demand-side management strategies. Pacific Northwest Laboratory (PNL) supports the FEMP mission of energy systems modernization. Under this charter, the Laboratory and its contractors work with federal facility energy managers to assess and implement energy-efficiency improvements at federal facilities nationwide.

Energy and technology review

International Nuclear Information System (INIS)

Quirk, W.J.; Bookless, W.A.

1994-05-01

The Lawrence Livermore National Laboratory, operated by the University of California for the United States Department of Energy, was established in 1952 to do research on nuclear weapons and magnetic fusion energy. Since then, in response to new national needs, we have added other major programs, including technology transfer, laser science (fusion, isotope separation, materials processing), biology and biotechnology, environmental research and remediation, arms control and nonproliferation, advanced defense technology, and applied energy technology. These programs, in turn, require research in basic scientific disciplines, including chemistry and materials science, computing science and technology, engineering, and physics. The Laboratory also carries out a variety of projects for other federal agencies. Energy and Technology Review is published monthly to report on unclassified work in all our programs. This issue reviews work performed in the areas of modified retoring for waste treatment and underground stripping to remove contamination

Marginalization of end-use technologies in energy innovation for climate protection

Science.gov (United States)

Wilson, Charlie; Grubler, Arnulf; Gallagher, Kelly S.; Nemet, Gregory F.

2012-11-01

Mitigating climate change requires directed innovation efforts to develop and deploy energy technologies. Innovation activities are directed towards the outcome of climate protection by public institutions, policies and resources that in turn shape market behaviour. We analyse diverse indicators of activity throughout the innovation system to assess these efforts. We find efficient end-use technologies contribute large potential emission reductions and provide higher social returns on investment than energy-supply technologies. Yet public institutions, policies and financial resources pervasively privilege energy-supply technologies. Directed innovation efforts are strikingly misaligned with the needs of an emissions-constrained world. Significantly greater effort is needed to develop the full potential of efficient end-use technologies.

Energy balance, costs and CO2 analysis of tillage technologies in maize cultivation

International Nuclear Information System (INIS)

Šarauskis, Egidijus; Buragienė, Sidona; Masilionytė, Laura; Romaneckas, Kęstutis; Avižienytė, Dovile; Sakalauskas, Antanas

2014-01-01

To achieve energy independence, Lithuania and other Baltic countries are searching for new ways to produce energy. Maize is a crop that is suitable for both food and forage, as well as for the production of bioenergy. The objective of this work was to assess the energy efficiency of maize cultivation technologies in different systems of reduced tillage. The experimental research and energy assessment was carried out for five different tillage systems: DP (deep ploughing), SP (), DC (deep cultivation), SC (shallow cultivation) and NT (no tillage). The assessment of the fuel inputs for these systems revealed that the greatest amount of diesel fuel (67.2 l ha −1 ) was used in the traditional DP system. The reduced tillage systems required 12–58% less fuel. Lower fuel consumption reduces the costs of technological operations and reduces CO 2 emissions, which are associated with the greenhouse effect. The agricultural machinery used in reduced tillage technologies emits 107–223 kg ha −1 of CO 2 gas into the environment, whereas DP emits 253 kg ha −1 of CO 2 . The energy analysis conducted in this study showed that the greatest total energy input (approximately 18.1 GJ ha −1 ) was associated with the conventional deep-ploughing tillage technology. The energy inputs associated with the reduced-tillage technologies, namely SP, DC and SC, ranged from 17.1 to 17.6 GJ ha −1 . The lowest energy input (16.2 GJ ha −1 ) was associated with the NT technology. Energy efficiency ratios for the various technologies were calculated as a function of the yield of maize grain and biomass. The best energy balance and the highest energy efficiency ratio (14.0) in maize cultivation was achieved with the NT technology. The energy efficiency ratios for DP, SP, DC and SC were 12.4, 13.4, 11.3 and 12.0, respectively. - Highlights: • Energetical and economic analysis of maize cultivation was done. • Reduced tillage technology reduces working time, fuel consumption

A switch by design : User-centred design of smart energy technologies to change habits of using energy at home

NARCIS (Netherlands)

Kobus, C.B.A.

2016-01-01

This doctoral thesis demonstrates that households are able and willing to permanently change their habits of using energy, if they are supported by well-designed, user-friendly technology. Previous studies have assessed the impact of smart energy technologies and new tariff structures to make

Battery Energy Storage Technology for power systems-An overview

DEFF Research Database (Denmark)

Chandrashekhara, Divya K; Østergaard, Jacob

2009-01-01

the present status of battery energy storage technology and methods of assessing their economic viability and impact on power system operation. Further, a discussion on the role of battery storage systems of electric hybrid vehicles in power system storage technologies had been made. Finally, the paper...... suggests a likely future outlook for the battery technologies and the electric hybrid vehicles in the context of power system applications....

Promoting renewable energy technologies

DEFF Research Database (Denmark)

Olsen, O.J.; Skytte, K.

2004-01-01

% of its annual electricity production. In this paper, we present and discuss the Danish experience as a case of promoting renewable energy technologies. The development path of the two technologies has been very different. Wind power is considered an outright success with fast deployment to decreasing...... technology and its particular context, it is possible to formulate some general principles that can help to create an effective and efficient policy for promoting new renewable energy technologies....

Moonlight project promotes energy-saving technology

Science.gov (United States)

Ishihara, A.

1986-01-01

In promoting energy saving, development of energy conservation technologies aimed at raising energy efficiency in the fields of energy conversion, its transportation, its storage, and its consumption is considered, along with enactment of legal actions urging rational use of energies and implementation of an enlightenment campaign for energy conservation to play a crucial role. Under the Moonlight Project, technical development is at present being centered around the following six pillars: (1) large scale energy saving technology; (2) pioneering and fundamental energy saving technology; (3) international cooperative research project; (4) research and survey of energy saving technology; (5) energy saving technology development by private industry; and (6) promotion of energy saving through standardization. Heat pumps, magnetohydrodynamic generators and fuel cells are discussed.

Towards a European Energy Technology Policy - The European Strategic Energy Technology Plan (Set-Plan)

International Nuclear Information System (INIS)

Mercier, A.; Petric, H.; Peteves, E.

2008-01-01

The transition to a low carbon economy will take decades and affect the entire economy. There is a timely opportunity for investment in energy infrastructure. However, decisions to invest in technologies that are fully aligned with policy and society priorities do not necessarily come naturally, although it will profoundly affect the level of sustainability of the European energy system for decades to come. Technology development needs to be accelerated and prioritized at the highest level of the European policy agenda. This is the essence of the European Strategic Energy Technology Plan (SET-Plan). The SET-Plan makes concrete proposals for action to establish an energy technology policy for Europe, with a new mind-set for planning and working together and to foster science for transforming energy technologies to achieve EU energy and climate change goals for 2020, and to contribute to the worldwide transition to a low carbon economy by 2050. This paper gives an overview of the SET-Plan initiative and highlights its latest developments. It emphasises the importance of information in support of decision-making for investing in the development of low carbon technologies and shows the first results of the technology mapping undertaken by the newly established Information System of the SET-Plan (SETIS).(author)

Risoe energy report 2. New and emerging bioenergy technologies

Energy Technology Data Exchange (ETDEWEB)

Larsen, H; Kossmann, J; Soenderberg Petersen, L [eds.

2003-11-01

Three growing concerns - sustainability (particularly in the transport sector), security of energy supply and climate change - have combined to increase interest in bioenergy. The trend towards bioenergy has been further encouraged by technological advances in biomass conversion and significant changes in energy markets. We even have a new term, 'modern bioenergy', to cover those areas of bioenergy technology - traditional as well as emerging - that could expand the role of bioenergy. Besides its potential to be carbon-neutral if produced sustainable, modern bioenergy shows the promise of covering a considerable part of the world's energy needs, increasing the security of energy supply through the use of indigenous resources, and improving local employment and land-use. To make these promises, however, requires further R and D. This report provides a critical examination of modern bioenergy, and describes current trends in both established and emerging bioenergy technologies. As well as examining the implications for the global energy scene, the report draws national conclusions for European and Danish energy supply, industry and energy research. The report presents the status of current R and D in biomass resources, supply systems, end products and conversion methods. A number of traditional and modern bioenergy technologies are assessed to show their current status, future trends and international R and D plans. Recent studies of emerging bioenergy technologies from international organisations and leading research organisations are reviewed. (BA)

Web based system for renewable energy sources assessment

International Nuclear Information System (INIS)

Shtrakov, Stanko; Ivanov, Lachezar South

2011-01-01

The RES A ssess software is developed to assist in the preliminary assessment of potential renewable energy projects. The first release includes water pumping solar systems, passive solar systems, wind, and geothermal energy and biomass. The program guides the users in the design of their systems, by providing initial estimates. By changing the system’s parameters, users are able to quickly screen an effective technology and system size depending on load, climatic conditions, and season of use. This paper describes scope of models (radiation, wind, geothermal, heat transfer) used to predict energy production from energy resource systems, climatic variables and system parameters and software technology for realising the project. Keywords: Energy projects, Renewable energy, Web system

Energy Assurance: Essential Energy Technologies for Climate Protection and Energy Security

Energy Technology Data Exchange (ETDEWEB)

Greene, David L [ORNL; Boudreaux, Philip R [ORNL; Dean, David Jarvis [ORNL; Fulkerson, William [University of Tennessee, Knoxville (UTK); Gaddis, Abigail [University of Tennessee, Knoxville (UTK); Graham, Robin Lambert [ORNL; Graves, Ronald L [ORNL; Hopson, Dr Janet L [University of Tennessee, Knoxville (UTK); Hughes, Patrick [ORNL; Lapsa, Melissa Voss [ORNL; Mason, Thom [ORNL; Standaert, Robert F [ORNL; Wilbanks, Thomas J [ORNL; Zucker, Alexander [ORNL

2009-12-01

We present and apply a new method for analyzing the significance of advanced technology for achieving two important national energy goals: climate protection and energy security. Quantitative metrics for U.S. greenhouse gas emissions in 2050 and oil independence in 2030 are specified, and the impacts of 11 sets of energy technologies are analyzed using a model that employs the Kaya identity and incorporates the uncertainty of technological breakthroughs. The goals examined are a 50% to 80% reduction in CO2 emissions from energy use by 2050 and increased domestic hydrocarbon fuels supply and decreased demand that sum to 11 mmbd by 2030. The latter is intended to insure that the economic costs of oil dependence are not more than 1% of U.S. GDP with 95% probability by 2030. Perhaps the most important implication of the analysis is that meeting both energy goals requires a high probability of success (much greater than even odds) for all 11 technologies. Two technologies appear to be indispensable for accomplishment of both goals: carbon capture and storage, and advanced fossil liquid fuels. For reducing CO2 by more than 50% by 2050, biomass energy and electric drive (fuel cell or battery powered) vehicles also appear to be necessary. Every one of the 11 technologies has a powerful influence on the probability of achieving national energy goals. From the perspective of technology policy, conflict between the CO2 mitigation and energy security is negligible. These general results appear to be robust to a wide range of technology impact estimates; they are substantially unchanged by a Monte Carlo simulation that allows the impacts of technologies to vary by 20%.

Spent Nuclear Fuel Alternative Technology Risk Assessment

Energy Technology Data Exchange (ETDEWEB)

Perella, V.F.

1999-11-29

A Research Reactor Spent Nuclear Fuel Task Team (RRTT) was chartered by the Department of Energy (DOE) Office of Spent Fuel Management with the responsibility to recommend a course of action leading to a final technology selection for the interim management and ultimate disposition of the foreign and domestic aluminum-based research reactor spent nuclear fuel (SNF) under DOE''s jurisdiction. The RRTT evaluated eleven potential SNF management technologies and recommended that two technologies, direct co-disposal and an isotopic dilution alternative, either press and dilute or melt and dilute, be developed in parallel. Based upon that recommendation, the Westinghouse Savannah River Company (WSRC) organized the SNF Alternative Technology Program to further develop the direct co-disposal and melt and dilute technologies and provide a WSRC recommendation to DOE for a preferred SNF alternative management technology. A technology risk assessment was conducted as a first step in this recommendation process to determine if either, or both, of the technologies posed significant risks that would make them unsuitable for further development. This report provides the results of that technology risk assessment.

Spent Nuclear Fuel Alternative Technology Risk Assessment

International Nuclear Information System (INIS)

Perella, V.F.

1999-01-01

A Research Reactor Spent Nuclear Fuel Task Team (RRTT) was chartered by the Department of Energy (DOE) Office of Spent Fuel Management with the responsibility to recommend a course of action leading to a final technology selection for the interim management and ultimate disposition of the foreign and domestic aluminum-based research reactor spent nuclear fuel (SNF) under DOE''s jurisdiction. The RRTT evaluated eleven potential SNF management technologies and recommended that two technologies, direct co-disposal and an isotopic dilution alternative, either press and dilute or melt and dilute, be developed in parallel. Based upon that recommendation, the Westinghouse Savannah River Company (WSRC) organized the SNF Alternative Technology Program to further develop the direct co-disposal and melt and dilute technologies and provide a WSRC recommendation to DOE for a preferred SNF alternative management technology. A technology risk assessment was conducted as a first step in this recommendation process to determine if either, or both, of the technologies posed significant risks that would make them unsuitable for further development. This report provides the results of that technology risk assessment

Summary of solar energy technology characterizations

Energy Technology Data Exchange (ETDEWEB)

D' Alessio, Dr., Gregory J.; Blaunstein, Dr., Robert R.

1980-09-01

This report summarizes the design, operating, energy, environmental, and economic characteristics of 38 model solar systems used in the Technology Assessment of Solar Energy Systems Project including solar heating and cooling of buildings, agricultural and industrial process heat, solar electric conversion, and industrial biomass systems. The generic systems designs utilized in this report were based on systems studies and mission analyses performed by the DOE National Laboratories and the MITRE Corporation. The purpose of those studies were to formulate materials and engineering cost data and performance data of solar equipment once mass produced.

Development of other oil-alternative energy technologies

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

Development efforts are being given on a large wind power generation system which has high reliability and economy and suits the actual situations in Japan. Verification tests will be conducted to establish control systems to realize load leveling against the increase in maximum power demand and the differences in demands between seasons, days and nights. Development will also be made on technologies for systems to operate devices optimally using nighttime power for household use. Solar light and heat energies will be introduced and used widely in housing to achieve efficient comprehensive energy utilization. Wastes, waste heat and unused energies locally available will be utilized to promote forming environment harmonious type energy communities. Photovoltaic and fuel cell power generation facilities will be installed on a trial basis to promote building a groundwork for full-scale installations. Photovoltaic power generation systems will be installed on actual houses to establish technologies to assess and optimize the load leveling effect. Attempts will be made on practical application of high-efficiency regional heat supply systems which utilize such unutilized energies as those from sea water and river water. Assistance will be given through preparing manuals on introduction of wastes power generation systems by local governments, and introduction of regional energy systems by using new discrete type power generation technologies and consumer-use cogeneration systems. 1 fig., 1 tab.

Environmental health risk assessment: Energy systems

International Nuclear Information System (INIS)

Krewski, D.; Somers, E.; Winthrop, S.O.

1984-01-01

Most industrialized nations have come to rely on a variety of systems for energy production, both of a conventional and non-conventional nature. In the paper, the spectrum of energy systems currently in use in Canada is outlined along with their potential health risks. Several examples of environmental health studies involving both outdoor and indoor air pollution related to energy production in Canada are reported. The limitations of current technologies for assessing health risks are discussed and possible approaches to managing energy related health risks are indicated. (author)

Critical Metals in Strategic Low-carbon Energy Technologies

Science.gov (United States)

Moss, R. L.

2012-04-01

Due to the rapid growth in demand for certain materials, compounded by political risks associated with the geographical concentration of the supply of them, shortages of materials could be a potential bottleneck to the deployment of low-carbon energy technologies. Consequently, an assessment has been carried out to ascertain whether such shortages could jeopardise the objectives of the EU's Strategic Energy Technology Plan (SET-Plan), especially in the six low-carbon energy technologies of SET-Plan, namely: nuclear, solar, wind, bioenergy, carbon capture and storage (CCS) and electricity grids. The assessment identified 14 metals for which the deployment of the six technologies will require 1% or more (and in some cases, much more) of current world supply per annum between 2020 and 2030. Following a more critical examination, based on the likelihood of rapid future global demand growth, limitations to expanding supply in the short to medium term, and the concentration of supply and political risks associated with key suppliers, 5 of the 14 metals were pinpointed to be at high risk, namely: the rare earth metals neodymium and dysprosium (for wind technology), and the by-products (from the processing of other metals) indium, tellurium and gallium (for photovoltaic technologies). In addition, the work has explored potential mitigation strategies, ranging from expanding European output, increasing recycling and reuse to reducing waste and finding substitutes for these metals in their main applications. Furthermore, recommendations are provided which include closely working with the EU's Raw Materials Initiative; supporting efforts to ensure reliable supply of ore concentrates at competitive prices; promoting R&D and demonstration projects on new lower cost separation processes; and promoting the further development of recycling technologies and increasing end-of-life collection

Materials, critical materials and clean-energy technologies

Directory of Open Access Journals (Sweden)

Eggert R.

2017-01-01

Full Text Available Modern engineered materials, components and systems depend on raw materials whose properties provide essential functionality to these technologies. Some of these raw materials are subject to supply-chain risks, and such materials are known as critical materials. This paper reviews corporate, national and world perspectives on material criticality. It then narrows its focus to studies that assess “what is critical” to clean-energy technologies. The focus on supply-chain risks is not meant to be alarmist but rather to encourage attention to monitoring these risks and pursuing technological innovation to mitigate the risks.

Low carbon Finland 2050. VTT clean energy technology strategies for society

Energy Technology Data Exchange (ETDEWEB)

Koljonen, T; Simila, L; Sipila, K [and others

2012-11-15

The Low Carbon Finland 2050 project by VTT Technical Research Centre of Finland aims to assess the technological opportunities and challenges involved in reducing Finland's greenhouse gas emissions. A target for reduction is set as at least 80% from the 1990 level by 2050 as part of an international effort, which requires strong RD and D in clean energy technologies. Key findings of the project are presented in this publication, which aims to stimulate enlightening and multidisciplinary discussions on low-carbon futures for Finland. The project gathered together VTT's technology experts in clean energy production, smart energy infrastructures, transport, buildings, and industrial systems as well as experts in energy system modelling and foresight. VTT's leading edge 'Low Carbon and Smart Energy' enables new solutions with a demonstration that is the first of its kind in Finland, and the introduction of new energy technology onto national and global markets. (orig.)

Indicative energy technology assessment of advanced rechargeable batteries

International Nuclear Information System (INIS)

Hammond, Geoffrey P.; Hazeldine, Tom

2015-01-01

significantly. ZEBRA batteries are presently one of the technologies of choice for EV development work. Nevertheless, compared to other ARBT, such batteries only represent an incremental step forward in terms of energy and environmental performance

Tidal current energy resource assessment in Ireland: Current status and future update

International Nuclear Information System (INIS)

O'Rourke, Fergal; Boyle, Fergal; Reynolds, Anthony

2010-01-01

Interest in renewable energy in Ireland has increased continually over the past decade. This interest is due primarily to security of supply issues and the effects of climate change. Ireland imports over 90% of its primary energy consumption, mostly in the form of fossil fuels. The exploitation of Ireland's vast indigenous renewable energy resources is required in order to reduce this over-dependence on fossil fuel imports to meet energy demand. Various targets have been set by the Irish government to incorporate renewable energy technologies into Ireland's energy market. As a result of these targets, the development in wind energy has increased substantially over the past decade; however this method of energy extraction is intermittent and unpredictable. Ireland has an excellent tidal current energy resource and the use of this resource will assist in the development of a sustainable energy future. Energy extraction using tidal current energy technologies offers a vast and predictable energy resource. This paper reviews the currently accepted tidal current energy resource assessment for Ireland. This assessment was compiled by Sustainable Energy Ireland in a report in 2004. The assessment employed a 2-dimensional numerical model of the tidal current velocities around Ireland, and from this numerical model the theoretical tidal current energy resource was identified. With the introduction of constraints and limitations, the technical, practical, accessible and viable tidal current energy resources were obtained. The paper discusses why the assessment needs updating including the effect on the assessment of the current stage of development of tidal current turbines and their deployment technology. (author)

New energy technologies. Report

International Nuclear Information System (INIS)

2004-01-01

This report on the new energy technologies has been written by a working group on request of the French ministry of economy, finances and industry, of the ministry of ecology and sustainable development, of the ministry of research and new technologies and of the ministry of industry. The mission of the working group is to identify goals and priority ways for the French and European research about the new technologies of energy and to propose some recommendations about the evolution of research incentive and sustain systems in order to reach these goals. The working group has taken into consideration the overall stakes linked with energy and not only the climatic change. About this last point, only the carbon dioxide emissions have been considered because they represent 90% of the greenhouse gases emissions linked with the energy sector. A diagnosis is made first about the present day context inside which the new technologies will have to fit with. Using this diagnosis, the research topics and projects to be considered as priorities for the short-, medium- and long-term have been identified: energy efficiency in transports, in dwellings/tertiary buildings and in the industry, development for the first half of the 21. century of an energy mix combining nuclear, fossil-fuels and renewable energy sources. (J.S.)

Energy Efficiency, Water Efficiency, and Renewable Energy Site Assessment: Seneca Rocks Discovery Center, Seneca Rocks, West Virginia

Energy Technology Data Exchange (ETDEWEB)

Kiatreungwattana, Kosol [National Renewable Energy Lab. (NREL), Golden, CO (United States); Salasovich, James [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kandt, Alicen [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-03-22

As part of ongoing efforts by the U.S. Forest Service to reduce energy use and incorporate renewable energy technologies into its facilities, the Department of Energy's National Renewable Energy Laboratory performed an energy efficiency and renewable energy site assessment of the Seneca Rocks Discovery Center in Seneca Rocks, West Virginia. This report documents the findings of this assessment, and provides site-specific information for the implementation of energy and water conservation measures, and renewable energy measures.

Exploring nuclear energy scenarios - implications of technology and fuel cycle choices

International Nuclear Information System (INIS)

Rayment, Fiona; Mathers, Dan; Gregg, Robert

2014-01-01

Nuclear Energy is recognised globally as a mature, reliable low carbon technology with a secure and abundant fuel source. Within the UK, Nuclear Energy is an essential contributor to the energy mix and as such a decision has been made to refresh the current nuclear energy plants to at least replacement of the existing nuclear fleet. This will mean the building of new nuclear power plant to ensure energy production of 16 GWe per annum. However it is also recognised that this may not be enough and as such expansion scenarios ranging from replacement of the existing fleet to 75 GWe nuclear energy capacity are being considered (see appendix). Within these energy scenarios, a variety of options are being evaluated including electricity generation only, electricity generation plus heat, open versus closed fuel cycles, Generation III versus Generation IV systems and combinations of the above. What is clear is that the deciding factor on the type and mix of any energy programme will not be on technology choice alone. Instead a complex mix of Government policy, relative cost of nuclear power, market decisions and public opinion will influence the rate and direction of growth of any future energy programme. The UK National Nuclear Laboratory has supported this work through the use and development of a variety of assessment and modelling techniques. When assessing nuclear energy scenarios, the technology chosen will impact on a number of parameters within each scenario which includes but is not limited to: - Economics, - Nuclear energy demand, - Fuel Supply, - Spent fuel storage / recycle, - Geological repository volumetric and radiological capacity, - Sustainability - effective resource utilisation, - Technology viability and readiness level. A number of assessment and modelling techniques have been developed and are described further. In particular, they examine fuel cycle options for a number of nuclear energy scenarios, whilst exploring key implications for a particular

Soft Energy Paths Revisited: Politics and Practice in Energy Technology Transitions

Directory of Open Access Journals (Sweden)

Chelsea Schelly

2016-10-01

Full Text Available This paper argues that current efforts to study and advocate for a change in energy technologies to reduce their climate and other environmental impacts often ignore the political, social, and bodily implications of energy technology choices. Framing renewable energy technologies exclusively in terms of their environmental benefits dismisses important questions about how energy infrastructures can be designed to correspond to democratic forms of socio-politics, forms of social organization that involve independence in terms of meeting energy needs, resilience in terms of adapting to change, participatory decision making and control, equitable distribution of knowledge and efficacy, and just distribution of ownership. Recognizing technological choices as political choices brings explicit attention to the kinds of socio-political restructuring that could be precipitated through a renewable energy technology transition. This paper argues that research on energy transitions should consider the political implications of technological choices, not just the environmental consequences. Further, emerging scholarship on energy practices suggests that social habits of energy usage are themselves political, in that they correspond to and reinforce particular arrangements of power. Acknowledging the embedded politics of technology, as the decades’ old concept of soft path technologies encourages, and integrating insights on the politics of technology with insights on technological practices, can improve future research on energy policy and public perceptions of energy systems. This paper extends insights regarding the socio-political implications of energy paths to consider how understandings of energy technologies as constellations of embedded bodily practices can help further develop our understanding of the consequences of energy technologies, consequences that move beyond environmental implications to the very habits and behaviors of patterned energy

Technologies for building integrated energy supply; Teknologier for bygningsintegreret energiforsyning

Energy Technology Data Exchange (ETDEWEB)

Katic, I.

2011-07-15

The current report is part of the deliverables from the project ''Building Integrated Energy Supply'' supported by the Danish Energy Authority R and D program. It describes a range of technologies for individual supply of heat and/or electricity to dwellings with respect to their stage of development and possible application in the near future. Energy supply of buildings is becoming more and more complex, partly as a result of increasing demands for comfort, efficiency and reduced emissions, partly as a result of rising oil prices and improved competitiveness of alternative energy sources. The days where ordinary boilers were the dominant source of individual supply of dwellings are becoming past these years. The challenge of the new range of technologies lies to a high extent in the fluctuating nature of their energy conversion and their interaction with the supply grids for heat and electricity. There is thus an increasing demand to understand the nature of the different supply technologies, besides a regular update of their economical key figures. The technologies briefly described in this study are: Solar heating, passive solar energy, biofuel boilers, heat pumps, micro CHP, solar photovoltaic and energy storage systems. The selected technologies are all assessed to play an important role in future's mix of supply technologies in Denmark, especially heat pumps and solar. (Author)

Interregional power transmission: a component in planning for renewable energy technologies

International Nuclear Information System (INIS)

Krueger Nielsen, S.; Soerensen, B.

2000-01-01

We discuss the role played by interregional power transmission on the basis of recent scenario work. In a project dealing with long-term planning for energy efficiency and renewable energy in Europe we modelled a scenario for the present 15 EU countries' energy system in 2050. The basis for the scenario is the concept of 'fair pricing' for energy services, meaning that the price of energy should reflect all externalities, but not otherwise be taxed or subsidized. The project assessed resource availability and expected technology price developments over time for a number of energy-related technologies, both on the supply side, the intermediate conversion chain and on the demand side. Among these, transmission technologies play an important role, both in smoothing out renewable energy supplies within the European Union region, and also allowing substantial import of energy from countries outside the EU having a surplus of renewable energy based power. (orig.)

Sustainability Assessment of Electricity Generation Technologies in Egypt Using Multi-Criteria Decision Analysis

Directory of Open Access Journals (Sweden)

Mostafa Shaaban

2018-05-01

Full Text Available Future electricity planning necessitates a thorough multi-faceted analysis of the available technologies in order to secure the energy supply for coming generations. To cope with worldwide concerns over sustainable development and meet the growing demands of electricity we assess the future potential technologies in Egypt through covering their technical, economic, environmental and social aspects. In this study we fill the gap of a lacking sustainability assessment of energy systems in Egypt where most of the studies focus mainly on the economic and technical aspects of planning future installation of power plants in Egypt. Furthermore, we include the stakeholder preferences of the indicators in the energy sector into our assessment. Moreover, we perform a sensitivity analysis through single dimension assessment scenarios of the technologies as well as a sustainable scenario with equal preferences of all dimensions of the sustainability. We employ two multi-criteria decision analysis (MCDA methodologies: the analytical hierarchy process for weighing the assessment criteria, and the weighted sum method for generating a general integrated sustainability index for each technology. The study investigates seven technologies: coal, natural gas, wind, concentrated solar power, photovoltaics, biomass and nuclear. The results reveal a perfect matching between the ranking of the technologies by the stakeholders and the sustainable scenario showing the highest ranking for natural gas and the lowest for nuclear and coal. There is a strong potential for renewable energy technologies to invade the electricity market in Egypt where they achieve the second ranking after natural gas. The Monte-Carlo approach gives photovoltaics a higher ranking over concentrated solar power as compared to the sample data ranking. The study concludes the importance of a multi-dimensional evaluation of the technologies while considering the preferences of the stakeholders in

Energy and cost saving results for advanced technology systems from the Cogeneration Technology Alternatives Study (CTAS)

Science.gov (United States)

Sagerman, G. D.; Barna, G. J.; Burns, R. K.

1979-01-01

An overview of the organization and methodology of the Cogeneration Technology Alternatives Study is presented. The objectives of the study were to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the future and to assess the advantages of advanced technology systems compared to those systems commercially available today. Advanced systems studied include steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics. Steam turbines, open cycle gas turbines, combined cycles, and diesel engines were also analyzed in versions typical of today's commercially available technology to provide a base against which to measure the advanced systems. Cogeneration applications in the major energy consuming manufacturing industries were considered. Results of the study in terms of plant level energy savings, annual energy cost savings and economic attractiveness are presented for the various energy conversion systems considered.

Risoe energy report 2. New and emerging bioenergy technologies

Energy Technology Data Exchange (ETDEWEB)

Larsen, H.; Kossmann, J.; Soenderberg Petersen, L. (eds.)

2003-11-01

Three growing concerns - sustainability (particularly in the transport sector), security of energy supply and climate change - have combined to increase interest in bioenergy. The trend towards bioenergy has been further encouraged by technological advances in biomass conversion and significant changes in energy markets. We even have a new term, 'modern bioenergy', to cover those areas of bioenergy technology - traditional as well as emerging - that could expand the role of bioenergy. Besides its potential to be carbon-neutral if produced sustainable, modern bioenergy shows the promise of covering a considerable part of the world's energy needs, increasing the security of energy supply through the use of indigenous resources, and improving local employment and land-use. To make these promises, however, requires further R and D. This report provides a critical examination of modern bioenergy, and describes current trends in both established and emerging bioenergy technologies. As well as examining the implications for the global energy scene, the report draws national conclusions for European and Danish energy supply, industry and energy research. The report presents the status of current R and D in biomass resources, supply systems, end products and conversion methods. A number of traditional and modern bioenergy technologies are assessed to show their current status, future trends and international R and D plans. Recent studies of emerging bioenergy technologies from international organisations and leading research organisations are reviewed. (BA)

Global Energy Assessment. Toward a Sustainable Future

Energy Technology Data Exchange (ETDEWEB)

Johansson, T B; Nakicenovic, N; Patwardhan, A; Gomez-Echeverri, L [eds.

2012-11-01

The Global Energy Assessment (GEA) brings together over 300 international researchers to provide an independent, scientifically based, integrated and policy-relevant analysis of current and emerging energy issues and options. It has been peer-reviewed anonymously by an additional 200 international experts. The GEA assesses the major global challenges for sustainable development and their linkages to energy; the technologies and resources available for providing energy services; future energy systems that address the major challenges; and the policies and other measures that are needed to realize transformational change toward sustainable energy futures. The GEA goes beyond existing studies on energy issues by presenting a comprehensive and integrated analysis of energy challenges, opportunities and strategies, for developing, industrialized and emerging economies. This volume is an invaluable resource for energy specialists and technologists in all sectors (academia, industry and government) as well as policymakers, development economists and practitioners in international organizations and national governments.

Low carbon Finland 2050. VTT clean energy technology strategies for society

Energy Technology Data Exchange (ETDEWEB)

Koljonen, T.; Simila, L.; Sipila, K. [and others

2012-11-15

The Low Carbon Finland 2050 project by VTT Technical Research Centre of Finland aims to assess the technological opportunities and challenges involved in reducing Finland's greenhouse gas emissions. A target for reduction is set as at least 80% from the 1990 level by 2050 as part of an international effort, which requires strong RD and D in clean energy technologies. Key findings of the project are presented in this publication, which aims to stimulate enlightening and multidisciplinary discussions on low-carbon futures for Finland. The project gathered together VTT's technology experts in clean energy production, smart energy infrastructures, transport, buildings, and industrial systems as well as experts in energy system modelling and foresight. VTT's leading edge 'Low Carbon and Smart Energy' enables new solutions with a demonstration that is the first of its kind in Finland, and the introduction of new energy technology onto national and global markets. (orig.)

Assessing the Atmospheric Pollution of Energy Facilities for Supporting Energy Policy Decisions

International Nuclear Information System (INIS)

Meneses Ruiz, E.; Alonso García, D.; Pérez Zayas, G.; Piñera Hernández, I.; Martinez Varona, M.; Molina Esquivel, E.

2015-01-01

The impacts of different energy facilities on the environment and human health are a matter of interest and concern throughout the world. For example, fossil fuels are one of the energy sources of more undesirable effects on the environment, but this energy is still one of the most competitive at the market, especially for the developing countries. However, it is necessary to find out a balance between the costs of achieving a lower level of environmental and health injury and the benefits of providing electricity at a reasonable cost. With a view to solving the current deficit in energy production (mainly in electricity generation) in the light of major transformations in the energy sector, the Cuban Government is evaluating ways of incorporating new sources and technologies and the expansion of existing capabilities. In this context non-fossil energy sources will play an increasingly important role. The present work shows the results obtained in the frame of the IAEA Technical Cooperation Project CUB7007. The project integrated several tools and methodologies in the field of air quality modelling and its assessment, emissions measurement and nuclear techniques. The main objective was to assess atmospheric pollution from various energy facilities for supporting energy policy decisions by incorporating nuclear techniques (proton-induced X–ray emission, neutron activation and X–ray fluorescence) for estimating the elementary composition of particulate matter. As results were consolidated national laboratories in the application of nuclear and nonnuclear techniques to support environmental studies, especially for the analysis of emissions in chimneys and ambient air sampling. Moreover, all energy technologies considered in the national strategy of development were assessed. (author)

Uncertainty in the learning rates of energy technologies. An experiment in a global multi-regional energy system model

International Nuclear Information System (INIS)

Rout, Ullash K.; Blesl, Markus; Fahl, Ulrich; Remme, Uwe; Voss, Alfred

2009-01-01

The diffusion of promising energy technologies in the market depends on their future energy production-cost development. When analyzing these technologies in an integrated assessment model using endogenous technological learning, the uncertainty in the assumed learning rates (LRs) plays a crucial role in the production-cost development and model outcomes. This study examines the uncertainty in LRs of some energy technologies under endogenous global learning implementation and presents a floor-cost modeling procedure to systematically regulate the uncertainty in LRs of energy technologies. The article narrates the difficulties of data assimilation, as compatible with mixed integer programming segmentations, and comprehensively presents the causes of uncertainty in LRs. This work is executed using a multi-regional and long-horizon energy system model based on 'TIMES' framework. All regions receive an economic advantage to learn in a common domain, and resource-ample regions obtain a marginal advantage for better exploitation of the learning technologies, due to a lower supply-side fuel-cost development. The lowest learning investment associated with the maximum LR mobilizes more deployment of the learning technologies. The uncertainty in LRs has an impact on the diffusion of energy technologies tested, and therefore this study scrutinizes the role of policy support for some of the technologies investigated. (author)

MEGASTAR: The meaning of growth. An assessment of systems, technologies, and requirements. [methodology for display and analysis of energy production and consumption

Science.gov (United States)

1974-01-01

A methodology for the display and analysis of postulated energy futures for the United States is presented. A systems approach methodology including the methodology of technology assessment is used to examine three energy scenarios--the Westinghouse Nuclear Electric Economy, the Ford Technical Fix Base Case and a MEGASTAR generated Alternate to the Ford Technical Fix Base Case. The three scenarios represent different paths of energy consumption from the present to the year 2000. Associated with these paths are various mixes of fuels, conversion, distribution, conservation and end-use technologies. MEGASTAR presents the estimated times and unit requirements to supply the fuels, conversion and distribution systems for the postulated end uses for the three scenarios and then estimates the aggregate manpower, materials, and capital requirements needed to develop the energy system described by the particular scenario.

Today's and future challenges in applications of renewable energy technologies for desalination

KAUST Repository

Goosen, Mattheus F A; Mahmoudi, Hacè ne; Ghaffour, NorEddine

2013-01-01

Recent trends and challenges in applications of renewable energy technologies for water desalination are critically reviewed with an emphasis on environmental concerns and sustainable development. After providing an overview of wind, wave, geothermal, and solar renewable energy technologies for fresh water production, hybrid systems are assessed. Then scale-up and economic factors are considered. This is followed with a section on regulatory factors, environmental concerns, and globalization, and a final segment on selecting the most suitable renewable energy technology for conventional and emerging desalination processes. © 2014 Copyright Taylor & Francis Group, LLC.

Today's and future challenges in applications of renewable energy technologies for desalination

KAUST Repository

Goosen, Mattheus F A

2013-08-28

Recent trends and challenges in applications of renewable energy technologies for water desalination are critically reviewed with an emphasis on environmental concerns and sustainable development. After providing an overview of wind, wave, geothermal, and solar renewable energy technologies for fresh water production, hybrid systems are assessed. Then scale-up and economic factors are considered. This is followed with a section on regulatory factors, environmental concerns, and globalization, and a final segment on selecting the most suitable renewable energy technology for conventional and emerging desalination processes. © 2014 Copyright Taylor & Francis Group, LLC.

A review on technology maturity of small scale energy storage technologies★

Directory of Open Access Journals (Sweden)

Nguyen Thu-Trang

2017-01-01

Full Text Available This paper reviews the current status of energy storage technologies which have the higher potential to be applied in small scale energy systems. Small scale energy systems can be categorized as ones that are able to supply energy in various forms for a building, or a small area, or a limited community, or an enterprise; typically, they are end-user systems. Energy storage technologies are classified based on their form of energy stored. A two-step evaluation is proposed for selecting suitable storage technologies for small scale energy systems, including identifying possible technical options, and addressing techno-economic aspects. Firstly, a review on energy storage technologies at small scale level is carried out. Secondly, an assessment of technology readiness level (TRL is conducted. The TRLs are ranked according to information gathered from literature review. Levels of market maturity of the technologies are addressed by taking into account their market development stages through reviewing published materials. The TRLs and the levels of market maturity are then combined into a technology maturity curve. Additionally, market driving factors are identified by using different stages in product life cycle. The results indicate that lead-acid, micro pumped hydro storage, NaS battery, NiCd battery, flywheel, NaNiCl battery, Li-ion battery, and sensible thermal storage are the most mature technologies for small scale energy systems. In the near future, hydrogen fuel cells, thermal storages using phase change materials and thermochemical materials are expected to become more popular in the energy storage market.

Experience Curves: A Tool for Energy Policy Assessment

Energy Technology Data Exchange (ETDEWEB)

Neij, Lena; Helby, Peter [Lund Univ. (Sweden). Environmental and Energy Systems Studies; Dannemand Andersen, Per; Morthorst, Poul Erik [Riso National Laboratory, Roskilde (Denmark); Durstewitz, Michael; Hoppe-Kilpper, Martin [Inst. fuer Solare Energieversorgungstechnik e.V., Kassel (DE); and others

2003-07-01

The objective of the project, Experience curves: a tool for energy policy assessment (EXTOOL), was to analyse the experience curve as a tool for the assessment of energy policy measures. This is of special interest, since the use of experience curves for the assessment of energy policy measures requires the development of the established experience curve methodology. This development raises several questions which have been addressed and analysed in this project. The analysis is based on case studies of wind power, an area with considerable experience in technology development, deployment and policy measures. Therefore, a case study based on wind power provides a good opportunity to study the usefulness of experience curves as a tool for the assessment of energy policy measures. However, the results are discussed in terms of using experience curves for the assessment of any energy technology. The project shows that experience curves can be used to assess the effect of combined policy measures in terms of cost reductions. Moreover, the result of the project show that experience curves could be used to analyse international 'learning systems', i.e. cost reductions brought about by the development of wind power and policy measures used in other countries. Nevertheless, the use of experience curves for the assessment of policy programmes has several limitations. First, the analysis and assessment of policy programmes cannot be achieved unless relevant experience curves based on good data can be developed. The authors are of the opinion that only studies that provide evidence of the validity, reliability and relevance of experience curves should be taken into account in policy making. Second, experience curves provide an aggregated picture of the situation and more detailed analysis of various sources of cost reduction, and cost reductions resulting from individual policy measures, requires additional data and analysis tools. Third, we do not recommend the use of

Carbon Capture: A Technology Assessment

Science.gov (United States)

2013-10-21

whereas laboratory-scale experiments typically seek to validate or obtain data for specific components of a system. Laboratory- and bench-scale processes...Plant,” Energy, vol. 35 (2010), pp. 841-850. E. Favre, R. Bounaceur, and D. Roizard, “ Biogas , Membranes and Carbon Dioxide Capture,” Journal of...pp. 1-49. 64 Favre, “ Biogas , Membranes.” Carbon Capture: A Technology Assessment Congressional Research Service 42 materials have pore sizes

High energy physics advisory panel's composite subpanel for the assessment of the status of accelerator physics and technology

International Nuclear Information System (INIS)

1996-05-01

In November 1994, Dr. Martha Krebs, Director of the US Department of Energy (DOE) Office of Energy Research (OER), initiated a broad assessment of the current status and promise of the field of accelerator physics and technology with respect to five OER programs -- High Energy Physics, Nuclear Physics, Basic Energy Sciences, Fusion Energy, and Health and Environmental Research. Dr. Krebs asked the High Energy Physics Advisory Panel (HEPAP) to establish a composite subpanel with representation from the five OER advisory committees and with a balance of membership drawn broadly from both the accelerator community and from those scientific disciplines associated with the OER programs. The Subpanel was also charged to provide recommendations and guidance on appropriate future research and development needs, management issues, and funding requirements. The Subpanel finds that accelerator science and technology is a vital and intellectually exciting field. It has provided essential capabilities for the DOE/OER research programs with an enormous impact on the nation's scientific research, and it has significantly enhanced the nation's biomedical and industrial capabilities. Further progress in this field promises to open new possibilities for the scientific goals of the OER programs and to further benefit the nation. Sustained support of forefront accelerator research and development by the DOE's OER programs and the DOE's predecessor agencies has been responsible for much of this impact on research. This report documents these contributions to the DOE energy research mission and to the nation

Technology Roadmaps: Wind Energy

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

Wind energy is perhaps the most advanced of the 'new' renewable energy technologies, but there is still much work to be done. This roadmap identifies the key tasks that must be undertaken in order to achieve a vision of over 2 000 GW of wind energy capacity by 2050. Governments, industry, research institutions and the wider energy sector will need to work together to achieve this goal. Best technology and policy practice must be identified and exchanged with emerging economy partners, to enable the most cost-effective and beneficial development.

Save Energy Now Assessments Results 2008 Detailed Report

Energy Technology Data Exchange (ETDEWEB)

Wright, Anthony L [ORNL; Martin, Michaela A [ORNL; Nimbalkar, Sachin U [ORNL; Quinn, James [U.S. Department of Energy; Glatt, Ms. Sandy [DOE Industrial Technologies Program; Orthwein, Mr. Bill [U.S. Department of Energy

2010-09-01

In October 2005, U.S. Department of Energy Secretary Bodman launched his Easy Ways to Save Energy campaign with a promise to provide energy assessments to 200 of the largest U.S. manufacturing plants. DOE's Industrial Technologies Program (ITP) responded to the Secretary's campaign with its Save Energy Now initiative, featuring a new and highly cost-effective form of energy savings assessment. The approach for these assessments drew heavily on the existing resources of ITP's technology delivery component. Over the years, ITP Technology Delivery has worked with industry partners to assemble a suite of respected software tools, proven assessment protocols, training curricula, certified energy experts, and strong partnerships for deployment. The Save Energy Now assessments conducted in calendar year 2006 focused on natural gas savings and targeted many of the nation's largest manufacturing plants - those that consume at least 1 TBtu of energy annually. The 2006 Save Energy Now assessments focused primarily on assessments of steam and process heating systems, which account for an estimated 74% of all natural gas use by U.S. manufacturing plants. Because of the success of the Save Energy Now assessments conducted in 2006 and 2007, the program was expanded and enhanced in two major ways in 2008: (1) a new goal was set to perform at least 260 assessments; and (2) the assessment focus was expanded to include pumping, compressed air, and fan systems in addition to steam and process heating. DOE ITP also has developed software tools to assess energy efficiency improvement opportunities in pumping, compressed air, and fan systems. The Save Energy Now assessments integrate a strong training component designed to teach industrial plant personnel how to use DOE's opportunity assessment software tools. This approach has the advantages of promoting strong buy-in of plant personnel for the assessment and its outcomes and preparing them better to

National Wind Technology Center sitewide, Golden, CO: Environmental assessment

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-01

The National Renewable Energy Laboratory (NREL), the nation`s primary solar and renewable energy research laboratory, proposes to expand its wind technology research and development program activities at its National Wind Technology Center (NWTC) near Golden, Colorado. NWTC is an existing wind energy research facility operated by NREL for the US Department of Energy (DOE). Proposed activities include the construction and reuse of buildings and facilities, installation of up to 20 wind turbine test sites, improvements in infrastructure, and subsequent research activities, technology testing, and site operations. In addition to wind turbine test activities, NWTC may be used to support other NREL program activities and small-scale demonstration projects. This document assesses potential consequences to resources within the physical, biological, and human environment, including potential impacts to: air quality, geology and soils, water resources, biological resources, cultural and historic resources, socioeconomic resources, land use, visual resources, noise environment, hazardous materials and waste management, and health and safety conditions. Comment letters were received from several agencies in response to the scoping and predecisional draft reviews. The comments have been incorporated as appropriate into the document with full text of the letters contained in the Appendices. Additionally, information from the Rocky Flats Environmental Technology Site on going sitewide assessment of potential environmental impacts has been reviewed and discussed by representatives of both parties and incorporated into the document as appropriate.

National Wind Technology Center sitewide, Golden, CO: Environmental assessment

International Nuclear Information System (INIS)

1996-11-01

The National Renewable Energy Laboratory (NREL), the nation's primary solar and renewable energy research laboratory, proposes to expand its wind technology research and development program activities at its National Wind Technology Center (NWTC) near Golden, Colorado. NWTC is an existing wind energy research facility operated by NREL for the US Department of Energy (DOE). Proposed activities include the construction and reuse of buildings and facilities, installation of up to 20 wind turbine test sites, improvements in infrastructure, and subsequent research activities, technology testing, and site operations. In addition to wind turbine test activities, NWTC may be used to support other NREL program activities and small-scale demonstration projects. This document assesses potential consequences to resources within the physical, biological, and human environment, including potential impacts to: air quality, geology and soils, water resources, biological resources, cultural and historic resources, socioeconomic resources, land use, visual resources, noise environment, hazardous materials and waste management, and health and safety conditions. Comment letters were received from several agencies in response to the scoping and predecisional draft reviews. The comments have been incorporated as appropriate into the document with full text of the letters contained in the Appendices. Additionally, information from the Rocky Flats Environmental Technology Site on going sitewide assessment of potential environmental impacts has been reviewed and discussed by representatives of both parties and incorporated into the document as appropriate

Technology choice and development in Brazil: An assessment of Brazil's alternative fuel program and the agriculture, manufacturing, energy, and service sectors

Science.gov (United States)

Nolan, Lucy A.

Technology choice profoundly affects a country's development process because capital-intensive and labor-intensive technologies have different socioeconomic linkages within the economy. This research examines the impacts of technology choice through the use of a social accounting matrix (SAM) framework. SAM-based modeling determines the direct and indirect effects of technology choice on development, particularly poverty alleviation in Brazil. Brazil's alternative fuel program was analyzed as a special example of technology choice. Two ethanol production technologies and the gasoline sector were compared; to make the study more robust, labor and capital intensive technologies were evaluated in the production of agriculture, manufacturing, energy, and services. Growth in these economic sectors was examined to assess the effects on employment, factor and household income, energy intensity, and carbon dioxide costs. Poverty alleviation was a focus, so income to unskilled agriculture labor, unskilled non-agriculture labor, and income to rural and urban households in poverty was also analyzed. The major research finding is that overall, labor-intensive technologies generate more employment, factor and household income, environmental and energy benefits to Brazil's economy than capital-intensive technologies. In addition, labor-intensive technologies make a particular contribution to poverty alleviation. The results suggest that policies to encourage the adoption of these technologies, especially in the agriculture and renewable energy sectors, are important because of their intersectoral linkages within the economy. Many studies have shown that Brazil's fuel ethanol program has helped to realize multiple macroeconomic objectives. However, this is the first empirical study to quantify its household income effects. The ethanol industry generated the most household income of the energy sectors. The research confirms a key finding of the appropriate technology literature

Nordic Energy Technologies : Enabling a sustainable Nordic energy future

Energy Technology Data Exchange (ETDEWEB)

Vik, Amund; Smith, Benjamin

2009-10-15

A high current Nordic competence in energy technology and an increased need for funding and international cooperation in the field are the main messages of the report. This report summarizes results from 7 different research projects relating to policies for energy technology, funded by Nordic Energy Research for the period 2007-2008, and provides an analysis of the Nordic innovation systems in the energy sector. The Nordic countries possess a high level of competence in the field of renewable energy technologies. Of the total installed capacity comprises a large share of renewable energy, and Nordic technology companies play an important role in the international market. Especially distinguished wind energy, both in view of the installed power and a global technology sales. Public funding for energy research has experienced a significant decline since the oil crisis of the 1970s, although the figures in recent years has increased a bit. According to the IEA, it will require a significant increase in funding to reduce greenhouse gas emissions and limit further climate change. The third point highlighted in the report is the importance of international cooperation in energy research. Nordic and international cooperation is necessary in order to reduce duplication and create the synergy needed if we are to achieve our ambitious policy objectives in the climate and energy issue. (AG)

Technology Assessment and Roadmap for the Emergency Radiation Dose Assessment Program

International Nuclear Information System (INIS)

Turteltaub, K W; Hartman-Siantar, C; Easterly, C; Blakely, W

2005-01-01

A Joint Interagency Working Group (JIWG) under the auspices of the Department of Homeland Security Office of Research and Development conducted a technology assessment of emergency radiological dose assessment capabilities as part of the overall need for rapid emergency medical response in the event of a radiological terrorist event in the United States. The goal of the evaluation is to identify gaps and recommend general research and development needs to better prepare the Country for mitigating the effects of such an event. Given the capabilities and roles for responding to a radiological event extend across many agencies, a consensus of gaps and suggested development plans was a major goal of this evaluation and road-mapping effort. The working group consisted of experts representing the Departments of Homeland Security, Health and Human Services (Centers for Disease Control and the National Institutes of Health), Food and Drug Administration, Department of Defense and the Department of Energy's National Laboratories (see appendix A for participants). The specific goals of this Technology Assessment and Roadmap were to: (1) Describe the general context for deployment of emergency radiation dose assessment tools following terrorist use of a radiological or nuclear device; (2) Assess current and emerging dose assessment technologies; and (3) Put forward a consensus high-level technology roadmap for interagency research and development in this area. This report provides a summary of the consensus of needs, gaps and recommendations for a research program in the area of radiation dosimetry for early response, followed by a summary of the technologies available and on the near-term horizon. We then present a roadmap for a research program to bring present and emerging near-term technologies to bear on the gaps in radiation dose assessment and triage. Finally we present detailed supporting discussion on the nature of the threats we considered, the status of technology

Technology Assessment and Roadmap for the Emergency Radiation Dose Assessment Program

Energy Technology Data Exchange (ETDEWEB)

Turteltaub, K W; Hartman-Siantar, C; Easterly, C; Blakely, W

2005-10-03

A Joint Interagency Working Group (JIWG) under the auspices of the Department of Homeland Security Office of Research and Development conducted a technology assessment of emergency radiological dose assessment capabilities as part of the overall need for rapid emergency medical response in the event of a radiological terrorist event in the United States. The goal of the evaluation is to identify gaps and recommend general research and development needs to better prepare the Country for mitigating the effects of such an event. Given the capabilities and roles for responding to a radiological event extend across many agencies, a consensus of gaps and suggested development plans was a major goal of this evaluation and road-mapping effort. The working group consisted of experts representing the Departments of Homeland Security, Health and Human Services (Centers for Disease Control and the National Institutes of Health), Food and Drug Administration, Department of Defense and the Department of Energy's National Laboratories (see appendix A for participants). The specific goals of this Technology Assessment and Roadmap were to: (1) Describe the general context for deployment of emergency radiation dose assessment tools following terrorist use of a radiological or nuclear device; (2) Assess current and emerging dose assessment technologies; and (3) Put forward a consensus high-level technology roadmap for interagency research and development in this area. This report provides a summary of the consensus of needs, gaps and recommendations for a research program in the area of radiation dosimetry for early response, followed by a summary of the technologies available and on the near-term horizon. We then present a roadmap for a research program to bring present and emerging near-term technologies to bear on the gaps in radiation dose assessment and triage. Finally we present detailed supporting discussion on the nature of the threats we considered, the status of

Energy consumption and technological developments

International Nuclear Information System (INIS)

Okorokov, V.R.

1990-02-01

The paper determines an outline of the world energy prospects based on principal trends of the development of energy consumption analysed over the long past period. According to the author's conclusion the development of energy systems will be determined in the nearest future (30 - 40 years) by contemporary energy technologies based on the exploitation of traditional energy resources but in the far future technologies based on the exploitation of thermonuclear and solar energy will play the decisive role. (author)

Structured Innovation of High-Performance Wave Energy Converter Technology: Preprint

Energy Technology Data Exchange (ETDEWEB)

Weber, Jochem W. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Laird, Daniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-01-25

Wave energy converter (WEC) technology development has not yet delivered the desired commercial maturity nor, and more importantly, the techno-economic performance. The reasons for this have been recognized and fundamental requirements for successful WEC technology development have been identified. This paper describes a multi-year project pursued in collaboration by the National Renewable Energy Laboratory and Sandia National Laboratories to innovate and develop new WEC technology. It specifies the project strategy, shows how this differs from the state-of-the-art approach and presents some early project results. Based on the specification of fundamental functional requirements of WEC technology, structured innovation and systemic problem solving methodologies are applied to invent and identify new WEC technology concepts. Using Technology Performance Levels (TPL) as an assessment metric of the techno-economic performance potential, high performance technology concepts are identified and selected for further development. System performance is numerically modelled and optimized and key performance aspects are empirically validated. The project deliverables are WEC technology specifications of high techno-economic performance technologies of TPL 7 or higher at TRL 3 with some key technology challenges investigated at higher TRL. These wave energy converter technology specifications will be made available to industry for further, full development and commercialisation (TRL 4 - TRL 9).

Assessing wave energy effects on biodiversity: the wave hub experience.

Science.gov (United States)

Witt, M J; Sheehan, E V; Bearhop, S; Broderick, A C; Conley, D C; Cotterell, S P; Crow, E; Grecian, W J; Halsband, C; Hodgson, D J; Hosegood, P; Inger, R; Miller, P I; Sims, D W; Thompson, R C; Vanstaen, K; Votier, S C; Attrill, M J; Godley, B J

2012-01-28

Marine renewable energy installations harnessing energy from wind, wave and tidal resources are likely to become a large part of the future energy mix worldwide. The potential to gather energy from waves has recently seen increasing interest, with pilot developments in several nations. Although technology to harness wave energy lags behind that of wind and tidal generation, it has the potential to contribute significantly to energy production. As wave energy technology matures and becomes more widespread, it is likely to result in further transformation of our coastal seas. Such changes are accompanied by uncertainty regarding their impacts on biodiversity. To date, impacts have not been assessed, as wave energy converters have yet to be fully developed. Therefore, there is a pressing need to build a framework of understanding regarding the potential impacts of these technologies, underpinned by methodologies that are transferable and scalable across sites to facilitate formal meta-analysis. We first review the potential positive and negative effects of wave energy generation, and then, with specific reference to our work at the Wave Hub (a wave energy test site in southwest England, UK), we set out the methodological approaches needed to assess possible effects of wave energy on biodiversity. We highlight the need for national and international research clusters to accelerate the implementation of wave energy, within a coherent understanding of potential effects-both positive and negative.

Waste-to-Energy: Hawaii and Guam Energy Improvement Technology Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Davis, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gelman, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tomberlin, G. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bain, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-03-01

The National Renewable Energy Laboratory (NREL) and the U.S. Navy have worked together to demonstrate new or leading-edge commercial energy technologies whose deployment will support the U.S. Department of Defense (DOD) in meeting its energy efficiency and renewable energy goals while enhancing installation energy security. This is consistent with the 2010 Quadrennial Defense Review report1 that encourages the use of 'military installations as a test bed to demonstrate and create a market for innovative energy efficiency and renewable energy technologies coming out of the private sector and DOD and Department of Energy laboratories,' as well as the July 2010 memorandum of understanding between DOD and the U.S. Department of Energy (DOE) that documents the intent to 'maximize DOD access to DOE technical expertise and assistance through cooperation in the deployment and pilot testing of emerging energy technologies.' As part of this joint initiative, a promising waste-to-energy (WTE) technology was selected for demonstration at the Hickam Commissary aboard the Joint Base Pearl Harbor-Hickam (JBPHH), Hawaii. The WTE technology chosen is called high-energy densification waste-to-energy conversion (HEDWEC). HEDWEC technology is the result of significant U.S. Army investment in the development of WTE technology for forward operating bases.

Interactions of energy technology development and new energy exploitation with water technology development in China

International Nuclear Information System (INIS)

Liang, Sai; Zhang, Tianzhu

2011-01-01

Interactions of energy policies with water technology development in China are investigated using a hybrid input-output model and scenario analysis. The implementation of energy policies and water technology development can produce co-benefits for each other. Water saving potential of energy technology development is much larger than that of new energy exploitation. From the viewpoint of proportions of water saving co-benefits of energy policies, energy sectors benefit the most. From the viewpoint of proportions of energy saving and CO 2 mitigation co-benefits of water technology development, water sector benefits the most. Moreover, economic sectors are classified into four categories concerning co-benefits on water saving, energy saving and CO 2 mitigation. Sectors in categories 1 and 2 have big direct co-benefits. Thus, they can take additional responsibility for water and energy saving and CO 2 mitigation. If China implements life cycle materials management, sectors in category 3 can also take additional responsibility for water and energy saving and CO 2 mitigation. Sectors in category 4 have few co-benefits from both direct and accumulative perspectives. Thus, putting additional responsibility on sectors in category 4 might produce pressure for their economic development. -- Highlights: ► Energy policies and water technology development can produce co-benefits for each other. ► For proportions of water saving co-benefits of energy policies, energy sectors benefit the most. ► For proportions of energy saving and CO 2 mitigation co-benefits of water policy, water sector benefits the most. ► China’s economic sectors are classified into four categories for policy implementation at sector scale.

Drying and energy technologies

CERN Document Server

Lima, A

2016-01-01

This book provides a comprehensive overview of essential topics related to conventional and advanced drying and energy technologies, especially motivated by increased industry and academic interest. The main topics discussed are: theory and applications of drying, emerging topics in drying technology, innovations and trends in drying, thermo-hydro-chemical-mechanical behaviors of porous materials in drying, and drying equipment and energy. Since the topics covered are inter- and multi-disciplinary, the book offers an excellent source of information for engineers, energy specialists, scientists, researchers, graduate students, and leaders of industrial companies. This book is divided into several chapters focusing on the engineering, science and technology applied in essential industrial processes used for raw materials and products.

Renewable Energy Technology

Science.gov (United States)

Daugherty, Michael K.; Carter, Vinson R.

2010-01-01

In many ways the field of renewable energy technology is being introduced to a society that has little knowledge or background with anything beyond traditional exhaustible forms of energy and power. Dotson (2009) noted that the real challenge is to inform and educate the citizenry of the renewable energy potential through the development of…

Technology Learning Ratios in Global Energy Models

International Nuclear Information System (INIS)

Varela, M.

2001-01-01

The process of introduction of a new technology supposes that while its production and utilisation increases, also its operation improves and its investment costs and production decreases. The accumulation of experience and learning of a new technology increase in parallel with the increase of its market share. This process is represented by the technological learning curves and the energy sector is not detached from this process of substitution of old technologies by new ones. The present paper carries out a brief revision of the main energy models that include the technology dynamics (learning). The energy scenarios, developed by global energy models, assume that the characteristics of the technologies are variables with time. But this trend is incorporated in a exogenous way in these energy models, that is to say, it is only a time function. This practice is applied to the cost indicators of the technology such as the specific investment costs or to the efficiency of the energy technologies. In the last years, the new concept of endogenous technological learning has been integrated within these global energy models. This paper examines the concept of technological learning in global energy models. It also analyses the technological dynamics of the energy system including the endogenous modelling of the process of technological progress. Finally, it makes a comparison of several of the most used global energy models (MARKAL, MESSAGE and ERIS) and, more concretely, about the use these models make of the concept of technological learning. (Author) 17 refs

Biomass Gasification Technology Assessment: Consolidated Report

Energy Technology Data Exchange (ETDEWEB)

Worley, M.; Yale, J.

2012-11-01

Harris Group Inc. (HGI) was commissioned by the National Renewable Energy Laboratory to assess gasification and tar reforming technologies. Specifically, the assessments focused on gasification and tar reforming technologies that are capable of producing a syngas suitable for further treatment and conversion to liquid fuels. HGI gathered sufficient information to analyze three gasification and tar reforming systems. This report summarizes the equipment, general arrangement of the equipment, operating characteristics, and operating severity for each technology. The order of magnitude capital cost estimates are supported by a basis-of-estimate write-up, which is also included in this report. The report also includes Microsoft Excel workbook models, which can be used to design and price the systems. The models can be used to analyze various operating capacities and pressures. Each model produces a material balance, equipment list, capital cost estimate, equipment drawings and preliminary general arrangement drawings. Example outputs of each model are included in the Appendices.

Workshop on power conditioning for alternative energy technologies. Executive summary

Energy Technology Data Exchange (ETDEWEB)

Smith, D. R.

1979-01-01

As various alternative energy technologies such as photovoltaics, wind, fuel cells, and batteries are emerging as potential sources of energy for the future, the need arises for development of suitable power-conditioning systems to interface these sources to their respective loads. Since most of these sources produce dc electricity and most electrical loads require ac, an important component of the required power-conditioning units is a dc-to-ac inverter. The discussions deal with the development of power conditioners for each alternative energy technology. Discussion topics include assessments of current technology, identification of operational requirements with a comparison of requirements for each source technology, the identification of future technology trends, the determination of mass production and marketing requirements, and recommendations for program direction. Specifically, one working group dealt with source technology: photovoltaics, fuel cells and batteries, and wind followed by sessions discussing system size and application: large grid-connected systems, small grid-connected systems, and stand alone and dc applications. A combined group session provided an opportunity to discuss problems common to power conditioning development.

Energy conversion technology by chemical processes

Energy Technology Data Exchange (ETDEWEB)

Oh, I W; Yoon, K S; Cho, B W [Korea Inst. of Science and Technology, Seoul (Korea, Republic of); and others

1996-12-01

The sharp increase in energy usage according to the industry development has resulted in deficiency of energy resources and severe pollution problems. Therefore, development of the effective way of energy usage and energy resources of low pollution is needed. Development of the energy conversion technology by chemical processes is also indispensable, which will replace the pollutant-producing and inefficient mechanical energy conversion technologies. Energy conversion technology by chemical processes directly converts chemical energy to electrical one, or converts heat energy to chemical one followed by heat storage. The technology includes batteries, fuel cells, and energy storage system. The are still many problems on performance, safety, and manufacturing of the secondary battery which is highly demanded in electronics, communication, and computer industries. To overcome these problems, key components such as carbon electrode, metal oxide electrode, and solid polymer electrolyte are developed in this study, followed by the fabrication of the lithium secondary battery. Polymer electrolyte fuel cell, as an advanced power generating apparatus with high efficiency, no pollution, and no noise, has many applications such as zero-emission vehicles, on-site power plants, and military purposes. After fabricating the cell components and operating the single cells, the fundamental technologies in polymer electrolyte fuel cell are established in this study. Energy storage technology provides the safe and regular heat energy, irrespective of the change of the heat energy sources, adjusts time gap between consumption and supply, and upgrades and concentrates low grade heat energy. In this study, useful chemical reactions for efficient storage and transport are investigated and the chemical heat storage technology are developed. (author) 41 refs., 90 figs., 20 tabs.

Technology Roadmaps: Nuclear Energy

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-07-01

This nuclear energy roadmap has been prepared jointly by the IEA and the OECD Nuclear Energy Agency (NEA). Unlike most other low-carbon energy sources, nuclear energy is a mature technology that has been in use for more than 50 years. The latest designs for nuclear power plants build on this experience to offer enhanced safety and performance, and are ready for wider deployment over the next few years. Several countries are reactivating dormant nuclear programmes, while others are considering nuclear for the first time. China in particular is already embarking on a rapid nuclear expansion. In the longer term, there is great potential for new developments in nuclear energy technology to enhance nuclear's role in a sustainable energy future.

Energy Efficiency, Water Efficiency, and Renewable Energy Site Assessment: San Juan National Forest - Dolores Ranger District, Colorado

Energy Technology Data Exchange (ETDEWEB)

Kandt, Alicen J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kiatreungwattana, Kosol [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2018-01-26

This report summarizes the results from an energy efficiency, water efficiency, and renewable energy site assessment of the Dolores Ranger District in the San Juan National Forest in Colorado. A team led by the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) conducted the assessment with United States Forest Service (USFS) personnel on August 16-17, 2016, as part of ongoing efforts by USFS to reduce energy and water use and implement renewable energy technologies. The assessment is approximately an American Society of Heating, Refrigerating, and Air-Conditioning Engineers Level 2 audit and meets Energy Independence and Security Act requirements.

Energy options for residential buildings assessment

International Nuclear Information System (INIS)

Rezaie, Behnaz; Dincer, Ibrahim; Esmailzadeh, Ebrahim

2013-01-01

Highlights: ► Studying various building energy options. ► Assessing these options from various points. ► Comparing these options for better environment and sustainability. ► Proposing renewable energy options as potential solutions. - Abstract: The building sector, as one of the major energy consumers, demands most of the energy research to assess different energy options from various aspects. In this paper, two similar residential buildings, with either low or high energy consumption patterns, are chosen as case studies. For these case studies, three different renewable energy technology and three different hybrid systems are designed for a specified size. Then, the environmental impact indices, renewable energy indices, and the renewable exergy indices have been estimated for every energy options. Results obtained show that the hybrid systems (without considering the economics factors) are superior and having top indices. The importance of the energy consumption patterns in buildings are proven by the indices. By cutting the energy consumption to about 40% the environment index would increase by more than twice (2.1). Utilization of the non-fossil fuels is one part of the solution to environmental problems while energy conservation being the other. It has been shown that the re-design of the energy consumption model is less complex but more achievable for buildings.

Gas-Fired Distributed Energy Resource Technology Characterizations

Energy Technology Data Exchange (ETDEWEB)

Goldstein, L.; Hedman, B.; Knowles, D.; Freedman, S. I.; Woods, R.; Schweizer, T.

2003-11-01

The U. S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE) is directing substantial programs in the development and encouragement of new energy technologies. Among them are renewable energy and distributed energy resource technologies. As part of its ongoing effort to document the status and potential of these technologies, DOE EERE directed the National Renewable Energy Laboratory to lead an effort to develop and publish Distributed Energy Technology Characterizations (TCs) that would provide both the department and energy community with a consistent and objective set of cost and performance data in prospective electric-power generation applications in the United States. Toward that goal, DOE/EERE - joined by the Electric Power Research Institute (EPRI) - published the Renewable Energy Technology Characterizations in December 1997.As a follow-up, DOE EERE - joined by the Gas Research Institute - is now publishing this document, Gas-Fired Distributed Energy Resource Technology Characterizations.

Technology Assessment for Powertrain Components Final Report CRADA No. TC-1124-95

Energy Technology Data Exchange (ETDEWEB)

Tokarz, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gough, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-10-19

LLNL utilized its defense technology assessment methodologies in combination with its capabilities in the energy; manufacturing, and transportation technologies to demonstrate a methodology that synthesized available but incomplete information on advanced automotive technologies into a comprehensive framework.

Assessment of the adequacy of US accelerator technology for Department of Energy missions

International Nuclear Information System (INIS)

Gerry, E.T.; Mani, S.A.

1983-09-01

Accelerator technology has made enormous impact across a wide field of research, industrial, and commercial endeavor and new developments are projected to broaden this technology transfer and open up new applications not previously possible or economically attractive. At the same time, however, the broad multi-agency base of support for the development of accelerator technology has largely evaporated leaving the program with the Department of Energy (DOE) Office of Energy Research (OER) as the only major National effort not directed at specific narrow applications. In order to continue to reap the benefits and spin-offs from this area of technology, an expanded long-term funding committment is vigorously endorsed since there appear to be major payoff potential in several areas of national need. Three specific recommendations are made that would accelerate the projected benefits from accelerator technology. An expanded effort should be undertaken to develop the key technologies of high brightness, high current, large area, long life, reliable ion, electron and RF sources along with associated studies directed toward accelerator design optimization. A centralized computational facility with a dedicated staff and library of programs for simulation of accelerator phenomenology should be created similar to that for the magnetic fusion program. Advanced accelerator R and D should be funded at a steady level to support a long range accelerator applications program

Energy Technology Perspectives 2012: Executive Summary

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-09-05

Energy Technology Perspectives (ETP) is the International Energy Agency's most ambitious publication on new developments in energy technology. It demonstrates how technologies -- from electric vehicles to smart grids -- can make a decisive difference in achieving the objective of limiting the global temperature rise to 2 C and enhancing energy security. ETP 2012 presents scenarios and strategies to 2050, with the aim of guiding decision makers on energy trends and what needs to be done to build a clean, secure and competitive energy future.

Solar Energy: Its Technologies and Applications

Science.gov (United States)

Auh, P. C.

1978-06-01

Solar heat, as a potential source of clean energy, is available to all of us. Extensive R and D efforts are being made to effectively utilize this renewable energy source. A variety of different technologies for utilizing solar energy have been proven to be technically feasible. Here, some of the most promising technologies and their applications are briefly described. These are: Solar Heating and Cooling of Buildings (SHACOB), Solar Thermal Energy Conversion (STC), Wind Energy Conversion (WECS), Bioconversion to Fuels (BCF), Ocean Thermal Energy Conversion (OTEC), and Photovoltaic Electric Power Systems (PEPS). Special emphasis is placed on the discussion of the SHACOB technologies, since the technologies are being expeditiously developed for the near commercialization.

Assessing the energy vulnerability: Case of industrialised countries

International Nuclear Information System (INIS)

Gnansounou, Edgard

2008-01-01

The emergence of new big consumer countries on the energy markets and the perspective of oil and gas depletion at the end of the current century raise the concerns about fair distribution of the remaining resources for the common and sustainable well-being of the mankind. High volatility of energy prices discourages the investment and delays the energy technology transition. Voluntary measures are needed mainly in industrialised countries in order to develop alternative and sustainable energy sources, to enable technology transfer towards emerging and developing countries and to avoid struggle for energy procurement. In this paper, a composite index of energy demand/supply weaknesses is defined as a proxy of energy vulnerability. The proposed index is based on several indicators such as energy intensity, oil and gas import dependency, CO 2 content of primary energy supply, electricity supply weaknesses and non-diversity in transport fuels. The assessment of this composite index for selected industrialised countries is discussed as well as the sensitivity to various factors

Advanced technologies and atomic energy

International Nuclear Information System (INIS)

1995-01-01

The expert committee on the research 'Application of advanced technologies to nuclear power' started the activities in fiscal year 1994 as one of the expert research committees of Atomic Energy Society of Japan. The objective of its foundation is to investigate the information on the advanced technologies related to atomic energy and to promote their practice. In this fiscal year, the advanced technologies in the fields of system and safety, materials and measurement were taken up. The second committee meeting was held in March, 1995. In this report, the contents of the lectures at the committee meeting and the symposium are compiled. The topics in the symposium were the meaning of advanced technologies, the advanced technologies and atomic energy, human factors and control and safety systems, robot technology and microtechnology, and functionally gradient materials. Lectures were given at two committee meetings on the development of atomic energy that has come to the turning point, the development of advanced technologies centering around ULSI, the present problems of structural fine ceramics and countermeasures of JFCC, the material analysis using laser plasma soft X-ray, and the fullerene research of advanced technology development in Power Reactor and Nuclear Fuel Development Corporation. (K.I.)

Energy-storage technologies and electricity generation

International Nuclear Information System (INIS)

Hall, Peter J.; Bain, Euan J.

2008-01-01

As the contribution of electricity generated from renewable sources (wind, wave and solar) grows, the inherent intermittency of supply from such generating technologies must be addressed by a step-change in energy storage. Furthermore, the continuously developing demands of contemporary applications require the design of versatile energy-storage/power supply systems offering wide ranges of power density and energy density. As no single energy-storage technology has this capability, systems will comprise combinations of technologies such as electrochemical supercapacitors, flow batteries, lithium-ion batteries, superconducting magnetic energy storage (SMES) and kinetic energy storage. The evolution of the electrochemical supercapacitor is largely dependent on the development of optimised electrode materials (tailored to the chosen electrolyte) and electrolytes. Similarly, the development of lithium-ion battery technology requires fundamental research in materials science aimed at delivering new electrodes and electrolytes. Lithium-ion technology has significant potential, and a step-change is required in order to promote the technology from the portable electronics market into high-duty applications. Flow-battery development is largely concerned with safety and operability. However, opportunities exist to improve electrode technology yielding larger power densities. The main barriers to overcome with regard to the development of SMES technology are those related to high-temperature superconductors in terms of their granular, anisotropic nature. Materials development is essential for the successful evolution of flywheel technology. Given the appropriate research effort, the key scientific advances required in order to successfully develop energy-storage technologies generally represent realistic goals that may be achieved by 2050

The Role of Emerging Technologies in Improving Energy Efficiency:Examples from the Food Processing Industry

Energy Technology Data Exchange (ETDEWEB)

Lung, Robert Bruce; Masanet, Eric; McKane, Aimee

2006-05-01

For over 25 years, the U.S. DOE's Industrial Technologies Program (ITP) has championed the application of emerging technologies in industrial plants and monitored these technologies impacts on industrial energy consumption. The cumulative energy savings of more than 160 completed and tracked projects is estimated at approximately 3.99 quadrillion Btu (quad), representing a production cost savings of $20.4 billion. Properly documenting the impacts of such technologies is essential for assessing their effectiveness and for delivering insights about the optimal direction of future technology research. This paper analyzes the impacts that several emerging technologies have had in the food processing industry. The analysis documents energy savings, carbon emissions reductions and production improvements and assesses the market penetration and sector-wide savings potential. Case study data is presented demonstrating the successful implementation of these technologies. The paper's conclusion discusses the effects of these technologies and offers some projections of sector-wide impacts.

International energy technology collaboration: benefits and achievements

International Nuclear Information System (INIS)

1996-01-01

The IEA Energy Technology Collaboration Programme facilitates international collaboration on energy technology research, development and deployment. More than 30 countries are involved in Europe, America, Asia, Australasia and Africa. The aim is to accelerate the development and deployment of new energy technologies to meet energy security, environmental and economic development goals. Costs and resources are shared among participating governments, utilities, corporations and universities. By co-operating, they avoid unproductive duplication and maximize the benefits from research budgets. The IEA Programme results every year in hundreds of publications which disseminate information about the latest energy technology developments and their commercial utilisation. The IEA Energy Technology Collaboration Programme operates through a series of agreements among governments. This report details the activities and achievements of all 41 agreements, covering energy technology information centres and Research and Development projects in fossil fuels, renewable energy efficient end-use, and nuclear fusion technologies. (authors). 58 refs., 9 tabs

Microelectronics in energy technology

Energy Technology Data Exchange (ETDEWEB)

Oeding, D; Jesse, G

1984-07-01

This meeting, which will take place on the 16th and 17th of October 1984 at the Old Opera House at Frankfurt on Main, in the context of the VDE Congress, will consist of 14 lectures on the state of the application of microelectronics to energy technology, and give its participants information on and a chance for discussion of this subject. The meeting will cover the following subjects: Microelectronics in energy supply undertakings; Microelectronics in the automation of power stations; Microelectronics in switchgear and transmission networks; Microelectronics in measurement technology; Microelectronics in lighting technology; Microelectronics in drive technology; Microelectronics in railway technology. The following shortened versions of these lectures are intended to motivate people to visit this event and to prepare contributions to and questions for the discussions.

Energy Technology Division research summary 1997

International Nuclear Information System (INIS)

1997-01-01

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy. As shown on the preceding page, the Division is organized into ten sections, five with concentrations in the materials area and five in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officers, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. The Division's capabilities are generally applied to issues associated with energy production, transportation, utilization or conservation, or with environmental issues linked to energy. As shown in the organization chart on the next page, the Division reports administratively to the Associate Laboratory Director (ALD) for Energy and Environmental Science and Technology (EEST) through the General Manager for Environmental and Industrial Technologies. While most of our programs are under the purview of the EEST ALD, we also have had programs funded under every one of the ALDs. Some of our research in superconductivity is funded through the Physical Research Program ALD. We also continue to work on a number of nuclear-energy-related programs under the ALD for Engineering Research. Detailed descriptions of our programs on a section-by-section basis are provided in the remainder of this book. This Overview highlights some major trends. Research related to the operational safety of commercial light water nuclear

Energy Technology Division research summary 1997.

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-21

The Energy Technology Division provides materials and engineering technology support to a wide range of programs important to the US Department of Energy. As shown on the preceding page, the Division is organized into ten sections, five with concentrations in the materials area and five in engineering technology. Materials expertise includes fabrication, mechanical properties, corrosion, friction and lubrication, and irradiation effects. Our major engineering strengths are in heat and mass flow, sensors and instrumentation, nondestructive testing, transportation, and electromechanics and superconductivity applications. The Division Safety Coordinator, Environmental Compliance Officers, Quality Assurance Representative, Financial Administrator, and Communication Coordinator report directly to the Division Director. The Division Director is personally responsible for cultural diversity and is a member of the Laboratory-wide Cultural Diversity Advisory Committee. The Division's capabilities are generally applied to issues associated with energy production, transportation, utilization or conservation, or with environmental issues linked to energy. As shown in the organization chart on the next page, the Division reports administratively to the Associate Laboratory Director (ALD) for Energy and Environmental Science and Technology (EEST) through the General Manager for Environmental and Industrial Technologies. While most of our programs are under the purview of the EEST ALD, we also have had programs funded under every one of the ALDs. Some of our research in superconductivity is funded through the Physical Research Program ALD. We also continue to work on a number of nuclear-energy-related programs under the ALD for Engineering Research. Detailed descriptions of our programs on a section-by-section basis are provided in the remainder of this book. This Overview highlights some major trends. Research related to the operational safety of commercial light water

Residential/commercial market for energy technologies

Energy Technology Data Exchange (ETDEWEB)

Glesk, M M

1979-08-01

The residential/commercial market sector, particularly as it relates to energy technologies, is described. Buildings account for about 25% of the total energy consumed in the US. Market response to energy technologies is influenced by several considerations. Some considerations discussed are: industry characteristics; market sectors; energy-consumption characeristics; industry forecasts; and market influences. Market acceptance may be slow or nonexistent, the technology may have little impact on energy consumption, and redesign or modification may be necessary to overcome belatedly perceived market barriers. 7 figures, 20 tables.

Hydrogen energy assessment

Energy Technology Data Exchange (ETDEWEB)

Salzano, F J; Braun, C [eds.

1977-09-01

The purpose of this assessment is to define the near term and long term prospects for the use of hydrogen as an energy delivery medium. Possible applications of hydrogen are defined along with the associated technologies required for implementation. A major focus in the near term is on industrial uses of hydrogen for special applications. The major source of hydrogen in the near term is expected to be from coal, with hydrogen from electric sources supplying a smaller fraction. A number of potential applications for hydrogen in the long term are identified and the level of demand estimated. The results of a cost benefit study for R and D work on coal gasification to hydrogen and electrolytic production of hydrogen are presented in order to aid in defining approximate levels of R and D funding. A considerable amount of data is presented on the cost of producing hydrogen from various energy resources. A key conclusion of the study is that in time hydrogen is likely to play a role in the energy system; however, hydrogen is not yet competitive for most applications when compared to the cost of energy from petroleum and natural gas.

Energy, technology, development

Energy Technology Data Exchange (ETDEWEB)

Goldemberg, J [Ministerio da Educacao, Brasilia (Brazil)

1992-02-01

Energy and technology are essential ingredients of development, it is only through their use that it became possible to sustain a population of almost 5 billion on Earth. The challenges to eradicate poverty and underdevelopment in developing countries in the face of strong population increases can only be successfully met with the use of advanced technology, leapfrogging the path followed in the past by today's industrialized countries. It is shown in the paper that energy consumption can be decoupled from economic development. Such possibility will contribute significantly in achieving sustainable development. 10 refs., 4 figs., 3 tabs.

Technological Aspects of Russian Energy Diplomacy

Directory of Open Access Journals (Sweden)

Stanislaw Z. Zhiznin

2016-01-01

Full Text Available In the present study we examined the impact of technology on the development of world energy in the world, as well as on the development of international energy relations. The important role of international cooperation in the field of energy technologies as a key factor in the development and global deployment of energy technologies in the industry. The most effective technology in the world of multilateral cooperation under the auspices of the International Energy Agency (IEA and other international organizations. It allows the joint efforts of the countries concerned to develop new technologies, test them and implement in production. For Russia, it is very important, because at the moment our country is not only a leading exporter of energy resources, but also has a significant impact on global energy security. At the same time Russia's FEC requires urgent and serious modernization through the development and introduction of innovative technologies on the basis of the study of international experience. Therefore the question of modernization of Russian fuel and energy complex has an international character. One way to accelerate the process of modernization of the organization is a public-private partnership that will largely depend on the nature and possibilities of Russian energy diplomacy, given the geopolitical and economic realities in connection with the sanctions imposed by Western countries against our country.

Use of comparative assessment framework for comparison of geological nuclear waste and CO2 disposal technologies

Energy Technology Data Exchange (ETDEWEB)

Streimikiene, Dalia

2010-09-15

Comparative assessment of few future energy and climate change mitigation options for Lithuania in 2020 performed indicated that nuclear and combined cycle gas turbine technologies are very similar energy options in terms of costs taking into account GHG emission reduction costs. Comparative assessment of these energy options requires evaluation of the potentials and costs for geological CO2 and nuclear waste storage as the main uncertainties in comparative assessment of electricity generation technologies are related with these back-end technologies. The paper analyses the main characteristics of possible geological storage of CO2 and NW options in Lithuania.

Technologies for power and thermal energy generation. Bring our energies together

International Nuclear Information System (INIS)

2014-05-01

On behalf of ADEME, the DREAL and the Region of Brittany and produced by ENEA, consulting company in energy and sustainable development, this brochure presents main technologies for power and thermal energy generation in an effort to maintain objectivity (efficiency, intrinsic features of each technology and key figures as regards power and energy). If most of the technologies are operational or in development in Brittany, such as ocean energy, the scope has been extended to encompass all existing technologies in France in order to give useful references. The French Brittany is a peninsula, with regards to both its geographic situation and its energy context. The region has decided to investigate energy and climate issue through the Brittany Energy Conference and to commit for energy transition. Discussions which have taken place since 2010 at the regional level as well as the national debate on energy transition in 2013 have highlighted the need for educational tools for the main energy generation technologies. Thus, the purpose of this brochure is to share energy stakes with a broad audience

Enabling science and technology for marine renewable energy

International Nuclear Information System (INIS)

Mueller, Markus; Wallace, Robin

2008-01-01

This paper describes some of the key challenges to be met in the development of marine renewable energy technology, from its present prototype form to being a widely deployed contributor to future energy supply. Since 2000, a number of large-scale wave and tidal current prototypes have been demonstrated around the world, but marine renewable energy technology is still 10-15 years behind that of wind energy. UK-based developers are leading the way, with Pelamis from Pelamis Wave Power demonstrated in the open sea, generating electricity into the UK network and securing orders from Portugal. However, having started later, the developing technology can make use of more advanced science and engineering, and it is therefore reasonable to expect rapid progress. Although progress is underway through deployment and testing, there are still key scientific challenges to be addressed in areas including resource assessment and predictability, engineering design and manufacturability, installation, operation and maintenance, survivability, reliability and cost reduction. The research priorities required to meet these challenges are suggested in this paper and have been drawn from current roadmaps and vision documents, including more recent consultations within the community by the UK Energy Research Centre Marine Research Network. Many scientific advances are required to meet these challenges, and their likelihood is explored based on current and future capabilities

The energy consumption and environmental impacts of SCR technology in China

Energy Technology Data Exchange (ETDEWEB)

Liang, Zengying; Ma, Xiaoqian; Lin, Hai; Tang, Yuting [School of Electric Power, Guangdong Key Laboratory of Clean Energy Technology, South China University of Technology, Guangzhou 510640 (China)

2011-04-15

Energy and environment are drawing greater attention today, particularly with the rapid development of the economy and increase consumption of energy in China. At present, coal-fired power plants are mainly responsible for atmospheric air pollution. The selective catalytic reduction (SCR) technology is a highly effective method for NO{sub X} control. The present study identified and quantified the energy consumption and the environmental impacts of SCR system throughout the whole life cycle, including production and transportation of manufacturing materials, installation and operation of SCR technology. The analysis was conducted with the utilization of life cycle assessment (LCA) methodology which provided a quantitative basis for assessing potential improvements in the environmental performance of the system. The functional unit of the study was 5454 t NO{sub X} emission from an existing Chinese pulverized coal power plant for 1 year. The current study compared life cycle emissions from two types of de-NO{sub X} technologies, namely the SCR technology and the selective non-catalytic reduction (SNCR) technology, and the case that NO{sub X} was emitted into atmosphere directly. The results showed that the environmental impact loading resulting from SCR technology (66810 PET{sub 2000}) was smaller than that of flue gas emitted into atmosphere directly (164121 PET{sub 2000}) and SNCR technology (105225 PET{sub 2000}). More importantly, the SCR technology is much more effective at the elimination of acidification and nutrient enrichment than SNCR technology and the case that NO{sub X} emitted into atmosphere directly. This SCR technology is more friendly to the environment, and can play an important role in NO{sub X} control for coal-fired power plants as well as industrial boilers. (author)

Impacts of FDI Renewable Energy Technology Spillover on China’s Energy Industry Performance

Directory of Open Access Journals (Sweden)

Weiwei Liu

2016-08-01

Full Text Available Environmental friendly renewable energy plays an indispensable role in energy industry development. Foreign direct investment (FDI in advanced renewable energy technology spillover is promising to improve technological capability and promote China’s energy industry performance growth. In this paper, the impacts of FDI renewable energy technology spillover on China’s energy industry performance are analyzed based on theoretical and empirical studies. Firstly, three hypotheses are proposed to illustrate the relationships between FDI renewable energy technology spillover and three energy industry performances including economic, environmental, and innovative performances. To verify the hypotheses, techniques including factor analysis and data envelopment analysis (DEA are employed to quantify the FDI renewable energy technology spillover and the energy industry performance of China, respectively. Furthermore, a panel data regression model is proposed to measure the impacts of FDI renewable energy technology spillover on China’s energy industry performance. Finally, energy industries of 30 different provinces in China based on the yearbook data from 2005 to 2011 are comparatively analyzed for evaluating the impacts through the empirical research. The results demonstrate that FDI renewable energy technology spillover has positive impacts on China’s energy industry performance. It can also be found that the technology spillover effects are more obvious in economic and technological developed regions. Finally, four suggestions are provided to enhance energy industry performance and promote renewable energy technology spillover in China.

Progress in sustainable energy technologies

CERN Document Server

Dincer, Ibrahim; Kucuk, Haydar

2014-01-01

This multi-disciplinary volume presents information on the state-of-the-art in sustainable energy technologies key to tackling the world's energy challenges and achieving environmentally benign solutions. Its unique amalgamation of the latest technical information, research findings and examples of successfully applied new developments in the area of sustainable energy will be of keen interest to engineers, students, practitioners, scientists and researchers working with sustainable energy technologies. Problem statements, projections, new concepts, models, experiments, measurements and simula

Program definition and assessment overview. [for thermal energy storage project management

Science.gov (United States)

Gordon, L. H.

1980-01-01

The implementation of a program level assessment of thermal energy storage technology thrusts for the near and far term to assure overall coherent energy storage program is considered. The identification and definition of potential thermal energy storage applications, definition of technology requirements, and appropriate market sectors are discussed along with the necessary coordination, planning, and preparation associated with program reviews, workshops, multi-year plans and annual operating plans for the major laboratory tasks.

Hawai‘i Distributed Energy Resource Technologies for Energy Security

Energy Technology Data Exchange (ETDEWEB)

None, None

2012-09-30

HNEI has conducted research to address a number of issues important to move Hawai‘i to greater use of intermittent renewable and distributed energy resource (DER) technologies in order to facilitate greater use of Hawai‘i's indigenous renewable energy resources. Efforts have been concentrated on the Islands of Hawai‘i, Maui, and O‘ahu, focusing in three areas of endeavor: 1) Energy Modeling and Scenario Analysis (previously called Energy Road mapping); 2) Research, Development, and Validation of Renewable DER and Microgrid Technologies; and 3) Analysis and Policy. These efforts focused on analysis of the island energy systems and development of specific candidate technologies for future insertion into an integrated energy system, which would lead to a more robust transmission and distribution system in the state of Hawai‘i and eventually elsewhere in the nation.

Current Renewable Energy Technologies and Future Projections

Energy Technology Data Exchange (ETDEWEB)

Allison, Stephen W [ORNL; Lapsa, Melissa Voss [ORNL; Ward, Christina D [ORNL; Smith, Barton [ORNL; Grubb, Kimberly R [ORNL; Lee, Russell [ORNL

2007-05-01

The generally acknowledged sources of renewable energy are wind, geothermal, biomass, solar, hydropower, and hydrogen. Renewable energy technologies are crucial to the production and utilization of energy from these regenerative and virtually inexhaustible sources. Furthermore, renewable energy technologies provide benefits beyond the establishment of sustainable energy resources. For example, these technologies produce negligible amounts of greenhouse gases and other pollutants in providing energy, and they exploit domestically available energy sources, thereby reducing our dependence on both the importation of fossil fuels and the use of nuclear fuels. The market price of renewable energy technologies does not reflect the economic value of these added benefits.

Comparative Assessment of Energy Supply Options

International Nuclear Information System (INIS)

Rogner, H.-H.; Vladu, I. F.

2000-01-01

The complexity facing today's energy planners and decision-makers, particularly in electricity sector, has increased. They must take into account many elements in selecting technologies and strategies that will impact near term energy development and applications in their countries. While costs remain a key factor, tradeoffs between the demands of environmental protection and economic development will have to be made. This fact, together with the needs of many countries to define their energy and electricity programmes in a sustainable manner, has resulted in a growing interest in the application of improved data, tools and techniques for comparative assessment of different electricity generation options, particularly from an environmental and human health viewpoint. Although global emissions of greenhouse gases and other pollutants, e.g. SO 2 , NO x and particulate, must be reduced, the reality today is that these emissions are increasing and are expected to continue increasing. In examining the air pollutants, as well as water effluents and solid waste generated by electricity production, it is necessary to assess the full energy chain from fuel extraction to waste disposal, including the production of construction and auxiliary materials. The paper describes this concept and illustrates its implementation for assessing and comparing electricity generation costs, emissions, wastes and other environmental burdens from different energy sources. (author)

Assessing medical technologies in development; a new paradigm of medical technology assessment

NARCIS (Netherlands)

Hummel, J. Marjan; van Rossum, Wouter; Verkerke, Gijsbertus Jacob; Rakhorst, Gerhard

2000-01-01

Objective: Our study aims to provide a practical contribution to the field of medical technology assessment within a new paradigm. This paradigm indicates the need for more comprehensive technology assessments in the development stage of a new technology. - Method: We introduce a method, based on

Assessing medical technologies in development - A new paradigm of medical technology assessment

NARCIS (Netherlands)

Hummel, MJM; van Rossum, W; Verkerke, GJ; Rakhorst, G

2000-01-01

Objective: Our study aims to provide a practical contribution to the field of medical technology assessment within a new paradigm. This paradigm indicates the need for more comprehensive technology assessments in the development stage of a new technology. Method: We introduce a method, based on

Trends in Energy Management Technology: BCS Integration Technologies - Open Communications Networking

Energy Technology Data Exchange (ETDEWEB)

Webster, Tom

2002-09-18

Our overall purpose in writing this series of articles is to provide Federal energy managers some basic informational tools to assist their decision making process relative to energy management systems design, specification, procurement, and energy savings potential. Since Federal buildings rely on energy management systems more than their commercial counterparts, it is important for energy practitioners to have a high level of knowledge and understanding of these complex systems. This is the second article in a series and will focus on building control system (BCS) networking fundamentals and an assessment of current approaches to open communications protocols. This is important because networking is a complex subject and the networks form the basic infrastructure for energy management functions and for integrating a wide variety of OEM equipment into a complete EMCIS. The first article [1] covered enabling technologies for emerging energy management systems. Future topics will concentrate on more practical aspects including applications software, product offerings, networking strategies, and case studies of actual installations. Please refer to the first article for a more complete overview of the purpose and background for this series.

How might renewable energy technologies fit in the food-water-energy nexus?

Science.gov (United States)

Newmark, R. L.; Macknick, J.; Heath, G.; Ong, S.; Denholm, P.; Margolis, R.; Roberts, B.

2011-12-01

Feeding the growing population in the U.S. will require additional land for crop and livestock production. Similarly, a growing population will require additional sources of energy. Renewable energy is likely to play an increased role in meeting the new demands of electricity consumers. Renewable energy technologies can differ from conventional technologies in their operation and their siting locations. Many renewable energy technologies have a lower energy density than conventional technologies and can also have large land use requirements. Much of the prime area suitable for renewable energy development in the U.S. has historically been used for agricultural production, and there is some concern that renewable energy installations could displace land currently producing food crops. In addition to requiring vast expanses of land, both agriculture and renewable energy can require water. The agriculture and energy sectors are responsible for the majority of water withdrawals in the U.S. Increases in both agricultural and energy demand can lead to increases in water demands, depending on crop management and energy technologies employed. Water is utilized in the energy industry primarily for power plant cooling, but it is also required for steam cycle processes and cleaning. Recent characterizations of water use by different energy and cooling system technologies demonstrate the choice of fuel and cooling system technologies can greatly impact the withdrawals and the consumptive use of water in the energy industry. While some renewable and conventional technology configurations can utilize more water per unit of land than irrigation-grown crops, other renewable technology configurations utilize no water during operations and could lead to reduced stress on water resources. Additionally, co-locating agriculture and renewable energy production is also possible with many renewable technologies, avoiding many concerns about reductions in domestic food production. Various

Assessment of renewable energy technology and a case of sustainable energy in mobile telecommunication sector.

Science.gov (United States)

Okundamiya, Michael S; Emagbetere, Joy O; Ogujor, Emmanuel A

2014-01-01

The rapid growth of the mobile telecommunication sectors of many emerging countries creates a number of problems such as network congestion and poor service delivery for network operators. This results primarily from the lack of a reliable and cost-effective power solution within such regions. This study presents a comprehensive review of the underlying principles of the renewable energy technology (RET) with the objective of ensuring a reliable and cost-effective energy solution for a sustainable development in the emerging world. The grid-connected hybrid renewable energy system incorporating a power conversion and battery storage unit has been proposed based on the availability, dynamism, and technoeconomic viability of energy resources within the region. The proposed system's performance validation applied a simulation model developed in MATLAB, using a practical load data for different locations with varying climatic conditions in Nigeria. Results indicate that, apart from being environmentally friendly, the increase in the overall energy throughput of about 4 kWh/$ of the proposed system would not only improve the quality of mobile services, by making the operations of GSM base stations more reliable and cost effective, but also better the living standards of the host communities.

Quadrennial Technology Review 2015: Technology Assessments--Marine and Hydrokinetic Power

Energy Technology Data Exchange (ETDEWEB)

Sam Baldwin, Gilbert Bindewald, Austin Brown, Charles Chen, Kerry Cheung, Corrie Clark, Joe Cresko,

2015-10-07

Marine and hydrokinetic (MHK) technologies convert the energy of waves, tides, and river and ocean currents into electricity. With more than 50% of the U.S. population living within 50 miles of the nation’s coasts, MHK technologies hold significant potential to supply renewable electricity to consumers in coastal load centers, particularly in the near term in areas with high costs of electricity and longer term in high resource areas in close proximity to major coastal load centers. MHK resource assessments identify a total U.S. technical resource potential of approximately 1250–1850 terawatt-hours (TWh) of generation per year from ocean wave, ocean current, ocean tidal, and river current energy. Of this, the U.S. continental technical resource potential is approximately 500–750 TWh/year. For context, roughly 90,000 homes can be powered by 1 TWh of electricity generation each year. A cost-effective MHK industry could provide a substantial amount of electricity for the nation owing in large part to its unique advantages as a source of energy, including its vast resource potential, its close proximity to major coastal load centers, and its long-term predictability and near-term forecastability.

Assessment of Energy Storage Alternatives in the Puget Sound Energy System

Energy Technology Data Exchange (ETDEWEB)

Balducci, Patrick J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jin, Chunlian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wu, Di [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Leslie, Patrick [Puget Sound Energy, Bellevue, WA (United States); Daitch, Charles [Puget Sound Energy, Bellevue, WA (United States); Marshall, A. [Primus Power, Hayward, CA (United States)

2013-12-01

As part of an ongoing study co-funded by the Bonneville Power Administration, under its Technology Innovation Grant Program, and the U.S. Department of Energy, the Pacific Northwest National Laboratory (PNNL) has developed an approach and modeling tool for assessing the net benefits of using energy storage located close to the customer in the distribution grid to manage demand. PNNL in collaboration with PSE and Primus Power has evaluated the net benefits of placing a zinc bromide battery system at two locations in the PSE system (Baker River / Rockport and Bainbridge Island). Energy storage can provide a number of benefits to the utility through the increased flexibility it provides to the grid system. Applications evaluated in the assessment include capacity value, balancing services, arbitrage, distribution deferral and outage mitigation. This report outlines the methodology developed for this study and Phase I results.

Renewable energy systems: A societal and technological platform

Energy Technology Data Exchange (ETDEWEB)

Polatidis, Heracles; Haralambopoulos, Dias A. [University of the Aegean, Mytilene (Greece). Department of Environment

2007-02-15

Today, the analysis of renewable energy places the emphasis on the technological and economic attributes with social and environmental impact assessment providing for a rather static, narrow frame of analysis. The participation and response of social actors and other stakeholders is usually of a traditional type, with consultation documents and public meetings, collection of complaints and suggestion schemes. This often encourages parochialism and an over-concentration on relatively trivial issues. It is, therefore, imperative to establish a new participatory planning platform to incorporate the wider socio-economic aspects of renewable energy systems and to provide for an operational analytical decomposition of them. In this work the issue of decomposition analysis is clarified, and a new agenda for the societal and technological decomposition analysis of renewable energy systems is developed. A case study is disclosed to present the relevance of the established platform for integrated (renewable) energy systems planning. Innovative aspects comprise of the simultaneous inclusion of decision analysis and social acceptance methods and tools in concert with the related public participation techniques. (author)

International energy technology collaboration and climate change mitigation. Case study 1. Concentrating Solar Power Technologies

Energy Technology Data Exchange (ETDEWEB)

Philibert, C. [Energy and Environment Division, International Energy Agency IEA, Paris (France)

2004-07-01

Mitigating climate change and achieving stabilisation of greenhouse gas atmospheric concentrations will require deep reductions in global emissions of energy-related carbon dioxide emissions. Developing and disseminating new, low-carbon energy technology will thus be needed. Two previous AIXG papers have focused on possible drivers for such a profound technological change: Technology Innovation, Development and Diffusion, released in June 2003, and International Energy Technology Collaboration and Climate Change Mitigation, released in June 2004. The first of these papers assesses a broad range of technical options for reducing energy-related CO2 emissions. It examines how technologies evolve and the role of research and development efforts, alternative policies, and short-term investment decisions in making long-term options available. It considers various policy tools that may induce technological change, some very specific, and others with broader expected effects. Its overall conclusion is that policies specifically designed to promote technical change, or 'technology push', could play a critical role in making available and affordable new energy technologies. However, such policies would not be sufficient to achieve the Convention's objective in the absence of broader policies. First, because there is a large potential for cuts that could be achieved in the short run with existing technologies; and second, the development of new technologies requires a market pull as much as a technology push. The second paper considers the potential advantages and disadvantages of international energy technology collaboration and transfer for promoting technological change. Advantages of collaboration may consist of lowering R and D costs and stimulating other countries to invest in R and D; disadvantage may include free-riding and the inefficiency of reaching agreement between many actors. This paper sets the context for further discussion on the role of

China's building energy demand: Long-term implications from a detailed assessment

International Nuclear Information System (INIS)

Eom, Jiyong; Clarke, Leon; Kim, Son H.; Kyle, Page; Patel, Pralit

2012-01-01

Buildings are an important contributor to China's energy consumption and attendant CO 2 emissions. Measures to address energy consumption and associated emissions from the buildings sector will be an important part of strategy to reduce the country's CO 2 emissions. This study presents a detailed, service-based model of China's building energy demand, nested in the GCAM (Global Change Assessment Model) integrated assessment framework. Using the model, we explored long-term pathways of China's building energy demand and identified opportunities to reduce greenhouse gas emissions. A range of different scenarios was also developed to gain insights into how China's building sector might evolve and what the implications might be for improved building energy technology and carbon policies. The analysis suggests that China's building energy growth will not wane anytime soon, although technology improvement will put downward pressure on this growth: In the reference scenarios, the sector's final energy demand will increase by 110–150% by 2050 and 160–220% by 2095 from its 2005 level. Also, regardless of the scenarios represented, the growth will involve the continued, rapid electrification of the buildings sector throughout the century, and this transition will be accelerated by the implementation of carbon policy. -- Highlights: ► We developed a building energy model for China, nested in an integrated-assessment framework. ► We explore long-term pathways of China's building energy use by implementing a range of scenarios. ► China's building energy consumption will continue to grow and be electrified over the century. ► Improved building energy technology will slow down the growth in building energy consumption. ► Electrification will be accelerated by the implementation of carbon policy.

Long-term affected energy production of waste to energy technologies identified by use of energy system analysis

DEFF Research Database (Denmark)

Münster, Marie; Meibom, Peter

2010-01-01

Affected energy production is often decisive for the outcome of consequential life-cycle assessments when comparing the potential environmental impact of products or services. Affected energy production is however difficult to determine. In this article the future long-term affected energy...... production is identified by use of energy system analysis. The focus is on different uses of waste for energy production. The Waste-to-Energy technologies analysed include co-combustion of coal and waste, anaerobic digestion and thermal gasification. The analysis is based on optimization of both investments...... and production of electricity, district heating and bio-fuel in a future possible energy system in 2025 in the countries of the Northern European electricity market (Denmark, Norway, Sweden, Finland and Germany). Scenarios with different CO2 quota costs are analysed. It is demonstrated that the waste...

Energy. Economics - politics - technology. Energie. Wirtschaft - Politik - Technik

Energy Technology Data Exchange (ETDEWEB)

Kruppa, A; Mielenhausen, E; Kallweit, J H; Schlueter, H; Schenkel, J; Vohwinkel, F; Streckel, S; Brockmann, H W

1978-01-01

The themes of the various aspects of the energy sector collected in this volume and discussed by different authors are: Energy policy, energy demand-research and forecasts, energy supplies, new technologies for future energy supply, generation of electrical energy by nuclear power stations, effect on the environment of energy plants, legal problems of site planning, and the authorisation of energy plants.

Advanced Energy Validated Photovoltaic Inverter Technology at NREL | Energy

Science.gov (United States)

Inverter Technology at NREL Advanced Energy Industries-NREL's first partner at the Energy Systems Integration Facility (ESIF)-validated its advanced photovoltaic (PV) inverter technology using the ESIF's computer screen in a laboratory, with power inverter hardware in the background Photo by Dennis Schroeder

Life Cycle Assessment of a Wave Energy Converter

OpenAIRE

Gastelum Zepeda, Leonardo

2017-01-01

Renewable energies had accomplish to become part of a new era in the energy development area, making people able to stop relying on fossil fuels. Nevertheless the environmental impacts of these new energy sources also require to be quantified in order to review how many benefits these new technologies have for the environment. In this project the use of a Life Cycle Assessment (LCA) will be implemented in order to quantify the environmental impact of wave energy, an LCA is a technique for ass...

Fiscal 1999 survey report on long-term energy technological strategies and the like. Long-term energy technological strategy survey (Medium-term energy technological strategy survey); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Choki energy gijutsu senryaku chosa (chuki energy gijutsu senryaku chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Energy strategies to be implemented under the New Sunshine Program by around 2010 have been compiled, with nation's industrial technological strategies, long-term energy outlook, and the like taken into consideration. The present survey aims to work out medium-term energy technological strategies. In Chapter 2, by conducting studies on the state of energy strategies in the national industry technological strategies as primarily compiled, long-term energy supply and demand outlook, and the history so far of the New Sunshine Program, and social conditions surrounding energy/environmental technologies and energy conditions are arranged in order and then analyzed with a view to deriving social needs. In Chapter 3, in view of the derived social needs, medium-term energy technological strategies are broken down into strategic target details, based on the important regions and major and minor strategic targets of the national industry technological strategies. In Chapter 4, medium-term energy technological strategies are worked out. In Chapter 5, 'basic ideas,' 'measures for promoting technology development,' 'return of the fruits to society' are mentioned as the methods of realizing the strategies. In Chapter 6, surveys and researches are summarized, and future development is predicted. (NEDO)

Renewable energy adoption in an ageing population: Heterogeneity in preferences for micro-generation technology adoption

Energy Technology Data Exchange (ETDEWEB)

Willis, Ken, E-mail: Ken.Willis@ncl.ac.uk [School of Architecture, Planning and Landscape, University of Newcastle, Newcastle upon Tyne NE1 7RU (United Kingdom); Scarpa, Riccardo [Department of Economics, Waikato School of Management, University of Waikato, Hamilton (New Zealand); Gilroy, Rose; Hamza, Neveen [School of Architecture, Planning and Landscape, University of Newcastle, Newcastle upon Tyne NE1 7RU (United Kingdom)

2011-10-15

Many countries are endeavouring to supply more of their energy from renewable resources. Such countries are also experiencing an aging population with a greater proportion of people aged {>=}65 years. This demographic shift may reduce the uptake of renewable energy, if older person households are less inclined to accept change and adopt new technologies. This paper assesses whether such households have different behavioural responses to energy efficiency compared to the rest of society and investigates whether micro-generation renewable energy technologies are less likely to be adopted by these households. It uses conditional logit and mixed logit models to investigate the impact of age of household on primary heating adoption, and also to assess the impact of older households on the installation of discretionary micro-generation technologies (solar thermal, solar voltaic, and wind power) to supplement existing heating and lighting systems. Results indicate that primary heating choice is not affected but that older person households are less inclined to adopt micro-generation technologies. - Highlights: > Heterogeneity exists in decisions on micro-generation technology installation. > Older person households are less inclined to adopt micro-generation technologies. > Micro-generation technologies fail a social cost-benefit analysis test.

Renewable energy adoption in an ageing population: Heterogeneity in preferences for micro-generation technology adoption

International Nuclear Information System (INIS)

Willis, Ken; Scarpa, Riccardo; Gilroy, Rose; Hamza, Neveen

2011-01-01

Many countries are endeavouring to supply more of their energy from renewable resources. Such countries are also experiencing an aging population with a greater proportion of people aged ≥65 years. This demographic shift may reduce the uptake of renewable energy, if older person households are less inclined to accept change and adopt new technologies. This paper assesses whether such households have different behavioural responses to energy efficiency compared to the rest of society and investigates whether micro-generation renewable energy technologies are less likely to be adopted by these households. It uses conditional logit and mixed logit models to investigate the impact of age of household on primary heating adoption, and also to assess the impact of older households on the installation of discretionary micro-generation technologies (solar thermal, solar voltaic, and wind power) to supplement existing heating and lighting systems. Results indicate that primary heating choice is not affected but that older person households are less inclined to adopt micro-generation technologies. - Highlights: → Heterogeneity exists in decisions on micro-generation technology installation. → Older person households are less inclined to adopt micro-generation technologies. → Micro-generation technologies fail a social cost-benefit analysis test.

Energy assessments

International Nuclear Information System (INIS)

Unruh, T.D.

1998-01-01

Energy industry initiatives during the 1970s and during the 1990s are compared. During the 1970s, the objective was to reduce energy consumption and to reduce dependency on foreign fuel. Today, the emphasis is on reducing energy costs and to improve net operating income. The challenges posed by the drive to reduce energy costs are discussed. As a tool in the drive to reduce energy cost, the energy assessment process was described. The process entails a detailed analysis of energy consumption, an investigation of energy rates and an assessment of site conditions and equipment, with a view towards an optimum combination that will lead to energy cost reductions

Sustainable Mobility: Using a Global Energy Model to Inform Vehicle Technology Choices in a Decarbonized Economy

Directory of Open Access Journals (Sweden)

Timothy Wallington

2013-04-01

Full Text Available The reduction of CO2 emissions associated with vehicle use is an important element of a global transition to sustainable mobility and is a major long-term challenge for society. Vehicle and fuel technologies are part of a global energy system, and assessing the impact of the availability of clean energy technologies and advanced vehicle technologies on sustainable mobility is a complex task. The global energy transition (GET model accounts for interactions between the different energy sectors, and we illustrate its use to inform vehicle technology choices in a decarbonizing economy. The aim of this study is to assess how uncertainties in future vehicle technology cost, as well as how developments in other energy sectors, affect cost-effective fuel and vehicle technology choices. Given the uncertainties in future costs and efficiencies for light-duty vehicle and fuel technologies, there is no clear fuel/vehicle technology winner that can be discerned at the present time. We conclude that a portfolio approach with research and development of multiple fuel and vehicle technology pathways is the best way forward to achieve the desired result of affordable and sustainable personal mobility. The practical ramifications of this analysis are illustrated in the portfolio approach to providing sustainable mobility adopted by the Ford Motor Company.

Economic and ordinal benefits of Hydrogen Energy Technology

International Nuclear Information System (INIS)

Giannantoni, C.; Zoli, M.

2009-01-01

A method for assessing economic, environmental and energy investments is particularly suited for hydrogen technologies, because it makes it possible to calculate business returns, negative externalities and, above all, the economic benefits to the citizens: the monetizable positive externalities and the ordinal benefits, i.e. those which cannot be reduced to a simple monetary value. [it

Fire-Protection Research for Energy-Technology Projects: FY 1981 year-end report

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, H.K.; Alvares, N.J.; Lipska-Quinn, A.E.; Beason, D.G.; Foote, K.L.; Priante, S.J.

1982-07-20

This report summarizes research conducted in fiscal year 1981 for the DOE-supported project, Fire Protection Research for Energy Technology Projects. Initiated in 1977, this ongoing research program was conceived to advance fire protection strategies for Energy Technology Projects to keep abreast of the unique fire problems that are developing with the complexity of energy technology research. We are developing an analytical methodology through detailed study of fusion energy experiments at Lawrence Livermore National Laboratory (LLNL). Employing these facilities as models for methodology development, we are simultaneously advancing three major task areas: (1) determination of unique fire hazards of current fusion energy facilities; (2) evaluation of the ability of accepted fire management measures to meet and negate hazards; and (3) performance of unique research into problem areas we have identified to provide input into analytical fire-growth and damage-assessment models.

Fire-Protection Research for Energy-Technology Projects: FY 1981 year-end report

International Nuclear Information System (INIS)

Hasegawa, H.K.; Alvares, N.J.; Lipska-Quinn, A.E.; Beason, D.G.; Foote, K.L.; Priante, S.J.

1982-01-01

This report summarizes research conducted in fiscal year 1981 for the DOE-supported project, Fire Protection Research for Energy Technology Projects. Initiated in 1977, this ongoing research program was conceived to advance fire protection strategies for Energy Technology Projects to keep abreast of the unique fire problems that are developing with the complexity of energy technology research. We are developing an analytical methodology through detailed study of fusion energy experiments at Lawrence Livermore National Laboratory (LLNL). Employing these facilities as models for methodology development, we are simultaneously advancing three major task areas: (1) determination of unique fire hazards of current fusion energy facilities; (2) evaluation of the ability of accepted fire management measures to meet and negate hazards; and (3) performance of unique research into problem areas we have identified to provide input into analytical fire-growth and damage-assessment models

Enabling Technologies for Ultra-Safe and Secure Modular Nuclear Energy

International Nuclear Information System (INIS)

Mendez Cruz, Carmen Margarita; Rochau, Gary E.; Middleton, Bobby; Rodriguez, Salvador B.; Rodriguez, Carmelo; Schleicher, Robert

2016-01-01

Sandia National Laboratories and General Atomics are pleased to respond to the Advanced Research Projects Agency-Energy (ARPA-e)'s request for information on innovative developments that may overcome various current reactor-technology limitations. The RFI is particularly interested in innovations that enable ultra-safe and secure modular nuclear energy systems. Our response addresses the specific features for reactor designs called out in the RFI, including a brief assessment of the current state of the technologies that would enable each feature and the methods by which they could be best incorporated into a reactor design.

Enabling Technologies for Ultra-Safe and Secure Modular Nuclear Energy

Energy Technology Data Exchange (ETDEWEB)

Mendez Cruz, Carmen Margarita [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rochau, Gary E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Middleton, Bobby [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rodriguez, Salvador B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rodriguez, Carmelo [General Atomics, San Diego, CA (United States); Schleicher, Robert [General Atomics, San Diego, CA (United States)

2016-06-01

Sandia National Laboratories and General Atomics are pleased to respond to the Advanced Research Projects Agency-Energy (ARPA-e)’s request for information on innovative developments that may overcome various current reactor-technology limitations. The RFI is particularly interested in innovations that enable ultra-safe and secure modular nuclear energy systems. Our response addresses the specific features for reactor designs called out in the RFI, including a brief assessment of the current state of the technologies that would enable each feature and the methods by which they could be best incorporated into a reactor design.

Economic aspects of advanced energy technologies

International Nuclear Information System (INIS)

Ramakumar, R.; Rodriguez, A.P.; Venkata, S.S.

1993-01-01

Advanced energy technologies span a wide variety of resources, techniques, and end-user requirements. Economic considerations are major factors that shape their harnessing and utilization. A discussion of the basic factors in the economic arena is presented, with particular emphasis on renewable energy technologies--photovoltaics, solar-thermal, wind-electric conversion, biomass utilization, hydro, and tidal and wave energy systems. The following are essential to determine appropriate energy system topologies: proper resource-need matching with an eye on the quality of energy requirements, integrated use of several resources and technologies, and a comprehensive consideration which includes prospecting, collection, conversion, transportation, distribution, storage and reconversion, end use, and subsequent waste management aspects. A few case studies are included to apprise the reader of the status of some of the key technologies and systems

Assessment of nuclear energy sustainability index using fuzzy logic

International Nuclear Information System (INIS)

Abouelnaga, Ayah E.; Metwally, Abdelmohsen; Aly, Naguib; Nagy, Mohammad; Agamy, Saeed

2010-01-01

Nuclear energy is increasingly perceived as an attractive mature energy generation technology that can deliver an answer to the worldwide increasing energy demand while respecting environmental concerns as well as contributing to a reduced dependence on fossil fuel. Advancing nuclear energy deployment demands an assessment of nuclear energy with respect to all sustainability dimensions. In this paper, the nuclear energy, whose sustainability will be assessed, is governed by the dynamics of three subsystems: environmental, economic, and sociopolitical. The overall sustainability is then a non-linear function of the individual sustainabilities. Each subsystem is evaluated by means of many components (pressure, status, and response). The combination of each group of indicators by means of fuzzy logic provides a measurement of sustainability for each subsystem.

Assessment of renewable energy reserves in Taiwan

International Nuclear Information System (INIS)

Chen, Falin; Lu, Shyi-Min; Tseng, Kuo-Tung; Wang, Eric; Lee, Si-Chen

2010-01-01

Since Taiwan imports more than 99% of energy supply from foreign countries, energy security has always been the first priority for government to formulate energy policy. The development of renewable energy not only contributes to the independence of energy supply, but also achieves benefits of economic development and environmental protection. Based upon information available to public, the present paper reassesses reserves of various renewable energies in Taiwan. The assessment includes seven kinds of renewable energies, namely, solar energy, wind power, biomass energy, wave energy, tidal energy, geothermal energy and hydropower, which are all commercialized and matured in terms of current technologies. Other renewable energies, which have not proven as matured as the aforementioned ones, are only assessed preliminarily in this paper, such as second generation of biomass, deep geothermal energy, the Kuroshio power generation and ocean thermal energy conversion. According to the estimation of this paper, the reserve of wind energy, up to 29.9 kWh/d/p (i.e., kWh per day per person), is the largest one among seven kinds of renewable energies in Taiwan, followed by 24.27 kWh/d/p of solar energy, 4.55 kWh/d/p of biomass, 4.58 kWh/d/p of ocean energy, 0.67 kWh/d/p of geothermal energy and 16.79 kWh/d/p of hydropower. If regarding biomass as a primary energy, and assuming 40% being the average efficiency to convert primary energy into electricity, the total power of the seven kinds of renewable energy reserves is about 78.03 kWh/d/p, which is equal to 2.75 times of 28.35 kWh/d/p of national power generation in 2008. If the reserves of 54.93 kWh/d/p estimated from other four kinds of renewable energies that have not technically matured yet are also taken into account, it will result that the reserves of renewable energy in Taiwan can be quite abundant. Although the results of the assessment point out that Taiwan has abundant renewable energy resources, the four inherent

New energy technologies

Energy Technology Data Exchange (ETDEWEB)

Schmidt-Kuester, W J; Wagner, H F

1977-01-01

In the Federal Republic of Germany, analyses and forecasts of the energy supply and energy consumption have revealed five major sectors in which extensive R and D activities should be carried out: nuclear energy, coal technology, the utilization of solar energy, techniques for the economical use of energy, and nuclear fusion. Of these sectors, only nuclear energy will be able to make a major contribution to our energy supply both in the near future and over a longer period. The available capacity for mining the large deposits of coal in the Federal Republic of Germany can be increased only gradually and will therefore not make an appreciable contribution until a later date. Another fact to be considered is that a rapidly expanding utilization of this source of energy entails very heavy pollution of the environment. The utilization of solar energy in Central Europe will probably be possible only for supplying warm water for industry and for heating buildings. In the long term, solar energy will contribute only a small percentage of energy to the supply required by the Federal Republic of Germany. Intensive efforts are being made to develop technologies for the more economical use of energy. The priorities in this sector are the installation of district heating systems using waste heat from power stations, and the improved heat insulation of houses. It is not anticipated that the technical utilization of nuclear fusion will be introduced before the end of this century. Nonetheless, this source of energy still constitutes a possibility offering an extremely great potential in the long term, with the result that every effort is being made to put it to good use. The work being carried out in this field in the Federal Republic of Germany is being closely coordinated with the relevant activities undertaken by the other member countries of the European Community.

Fire protection research for energy technology projects; FY 79 year-end report

International Nuclear Information System (INIS)

Hasegawa, H.K.; Alvares, N.J.; Lipska, A.E.; Ford, H.; Beason, D.G.

1981-01-01

This report describes work performed in fiscal year 1979, on a DOE funded study entitled Fire Protection Research for Energy Technology Projects. The primary goal of this program is to ensure that fire protection measures for Fusion Energy Experiments (FEE) evolve concurrently with the complexity of FEE. Ultimately, it is planned that the detailed study of fusion experiments will provide an analytical methodology which can be applied to the full range of energy technology projects. We attempt to achieve this objective by coordinately advancing 3 (three) major task areas; (a) determine the fire hazards of current FEE facilities (b) assess the ability of accepted fire management strategies to meet and negate the hazard, (c) perform unique research into problem areas we have identified to provide input into analytical fire growth and damage assessment models

Human factors assessments of D and D technologies

International Nuclear Information System (INIS)

Carpenter, C.P.; Evans, T.T.; McCabe, B.

2000-01-01

On April 2, 1997, the US Secretary of Energy directed the US Assistant Secretary of Environmental Management and of Safety and Health to require field input of appropriate data to ensure that safety and health considerations were properly addressed in the Accelerating Cleanup: Focus on 2006 Plan. The US Department of Energy (DOE) field managers have committed to the Secretary that they will fully implement integrated safety management systems (ISMSs) at their respective sites by the end of fiscal year 1999. The Secretary has further directed that headquarters safety and health guidance be developed to support consistent and comprehensive project baseline summaries from the field. The Secretary has committed to institutionalizing ISMS as an integral component of the way the DOE conducts its business. The Defense Nuclear Facilities Safety Board continues to oversee and closely monitor the DOE's commitment to the safety and health of its workers. The DOE is committed to a management system approach to ensure that work is performed in a manner that protects the worker, public, and environment. The Deactivation and Decommissioning Focus Area (DDFA) is actively addressing the need to incorporate environmental safety and health (ES and H) considerations in developing technologies. The DDFA is partnered with the Operating Engineers National Hazmat Program (OENHP) to evaluate the ES and H considerations of the innovative and improved decontamination and decommissioning technologies. Part of the implementation of the ES and H work practices in the field is through a cooperative agreement between the National Energy Technology Laboratory (NETL) and the OENHP. The objective of this program is to establish an International Environmental Technology and Training Center to conduct human factors assessments and protocols on environmental technologies. The intent of the human factors assessments is to enhance the effectiveness and efficiency of the technologies and to enhance

Solar Energy Technologies Office Fact Sheet

Energy Technology Data Exchange (ETDEWEB)

Solar Energy Technologies Office

2018-03-13

The U.S. Department of Energy Solar Energy Technologies Office (SETO) supports early-stage research and development to improve the affordability, reliability, and performance of solar technologies on the grid. The office invests in innovative research efforts that securely integrate more solar energy into the grid, enhance the use and storage of solar energy, and lower solar electricity costs.

The new energy technologies in Australia; Les nouvelles technologies de l'energie en Australie

Energy Technology Data Exchange (ETDEWEB)

Le Gleuher, M.; Farhi, R

2005-06-15

The large dependence of Australia on the fossil fuels leads to an great emission of carbon dioxide. The Australia is thus the first greenhouse gases emitter per habitant, in the world. In spite of its sufficient fossil fuels reserves, the Australia increases its production of clean energies and the research programs in the domain of the new energies technology. After a presentation of the australia situation, the authors detail the government measures in favor of the new energy technologies and the situation of the hydroelectricity, the wind energy, the wave and tidal energy, the biomass, the biofuels, the solar energy, the ''clean'' coal, the hydrogen and the geothermal energy. (A.L.B.)

Developing Information on Energy Savings and Associated Costs and Benefits of Energy Efficient Emerging Technologies Applicable in California

Energy Technology Data Exchange (ETDEWEB)

Xu, Tengfang; Slaa, Jan Willem; Sathaye, Jayant

2010-12-15

California Energy Commission (CEC) and managed by California Institute for Energy and Environment (CIEE). The project purpose is to characterize energy savings, technology costs, market potential, and economic viability of newly selected technologies applicable to California. In this report, LBNL first performed technology reviews to identify new or under-utilized technologies that could offer potential in improving energy efficiency and additional benefits to California industries as well as in the U.S. industries, followed by detailed technology assessment on each targeted technology, with a focus on California applications. A total of eleven emerging or underutilized technologies applicable to California were selected and characterized with detailed information in this report. The outcomes essentially include a multi-page summary profile for each of the 11 emerging or underutilized technologies applicable to California industries, based on the formats used in the technology characterization reports (Xu et al. 2010; Martin et al. 2000).

Smart City Energy Interconnection Technology Framework Preliminary Research

Science.gov (United States)

Zheng, Guotai; Zhao, Baoguo; Zhao, Xin; Li, Hao; Huo, Xianxu; Li, Wen; Xia, Yu

2018-01-01

to improve urban energy efficiency, improve the absorptive ratio of new energy resources and renewable energy sources, and reduce environmental pollution and other energy supply and consumption technology framework matched with future energy restriction conditions and applied technology level are required to be studied. Relative to traditional energy supply system, advanced information technology-based “Energy Internet” technical framework may give play to energy integrated application and load side interactive technology advantages, as a whole optimize energy supply and consumption and improve the overall utilization efficiency of energy.

Morgantown Energy Technology Center, technology summary

International Nuclear Information System (INIS)

1994-06-01

This document has been prepared by the DOE Environmental Management (EM) Office of Technology Development (OTD) to highlight its research, development, demonstration, testing, and evaluation activities funded through the Morgantown Energy Technology Center (METC). Technologies and processes described have the potential to enhance DOE's cleanup and waste management efforts, as well as improve US industry's competitiveness in global environmental markets. METC's R ampersand D programs are focused on commercialization of technologies that will be carried out in the private sector. META has solicited two PRDAs for EM. The first, in the area of groundwater and soil technologies, resulted in twenty-one contact awards to private sector and university technology developers. The second PRDA solicited novel decontamination and decommissioning technologies and resulted in eighteen contract awards. In addition to the PRDAs, METC solicited the first EM ROA in 1993. The ROA solicited research in a broad range of EM-related topics including in situ remediation, characterization, sensors, and monitoring technologies, efficient separation technologies, mixed waste treatment technologies, and robotics. This document describes these technology development activities

Perspectives of energy efficient technologies penetration in the Greek domestic sector, through the analysis of Energy Performance Certificates

International Nuclear Information System (INIS)

Gelegenis, J.; Diakoulaki, D.; Lampropoulou, H.; Giannakidis, G.; Samarakou, M.; Plytas, N.

2014-01-01

The building sector in Greece presents a huge energy saving potential, the largest part of which is remaining unexploited. The recently enacted legislation for the energy performance of buildings, in combination with the financial support provided by funding programmes to low income families is expected to significantly boost the deployment of energy efficient technologies in the Greek domestic sector. The exploitation of these legal and financial instruments follows a formalised process of energy audits, resulting in buildings classification and in the submission of Energy Performance Certificates (EPCs) including suggestions to improve the dwellings' energy performance. The paper aims at an ex-ante evaluation of the market trends revealed by EPCs in Greece, in order to identify the perspectives of individual technologies and to assess the degree to which the certification procedure helps in improving the energy performance of buildings. The results indicate a strong trend towards less cost-effective technologies, revealing a sub-optimal allocation of financial resources and putting into risk the path towards the achievement of EU targets for 2020. - Highlights: • Energy Performance Certificates reveal market trends of energy efficient technologies. • SWH, replacement of windows and walls/roof insulation are most often recommended. • Other measures are controls, switch to NG; low cost measures are rarely recommended. • Cost-effectiveness is not the main factor explaining technology recommendations. • Amendment of EPC document and inspection process may enhance its effectiveness

Fiscal 1999 survey report on long-term energy technological strategies and the like. Long-term energy technological strategy survey (Medium-term energy technological strategy survey); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Choki energy gijutsu senryaku chosa (chuki energy gijutsu senryaku chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Energy strategies to be implemented under the New Sunshine Program by around 2010 have been compiled, with nation's industrial technological strategies, long-term energy outlook, and the like taken into consideration. The present survey aims to work out medium-term energy technological strategies. In Chapter 2, by conducting studies on the state of energy strategies in the national industry technological strategies as primarily compiled, long-term energy supply and demand outlook, and the history so far of the New Sunshine Program, and social conditions surrounding energy/environmental technologies and energy conditions are arranged in order and then analyzed with a view to deriving social needs. In Chapter 3, in view of the derived social needs, medium-term energy technological strategies are broken down into strategic target details, based on the important regions and major and minor strategic targets of the national industry technological strategies. In Chapter 4, medium-term energy technological strategies are worked out. In Chapter 5, 'basic ideas,' 'measures for promoting technology development,' 'return of the fruits to society' are mentioned as the methods of realizing the strategies. In Chapter 6, surveys and researches are summarized, and future development is predicted. (NEDO)

Integrated assessment of bioelectricity technology options

International Nuclear Information System (INIS)

Thornley, Patricia; Upham, Paul; Huang, Ye; Rezvani, Sina; Brammer, John; Rogers, John

2009-01-01

Power generation from biomass is a sustainable energy technology which can contribute to substantial reductions in greenhouse gas emissions, but with greater potential for environmental, economic and social impacts than most other renewable energy technologies. It is important therefore in assessing bioenergy systems to take account of not only technical, but also environmental, economic and social parameters on a common basis. This work addresses the challenge of analysing, quantifying and comparing these factors for bioenergy power generation systems. A life-cycle approach is used to analyse the technical, environmental, economic and social impacts of entire bioelectricity systems, with a number of life-cycle indicators as outputs to facilitate cross-comparison. The results show that similar greenhouse gas savings are achieved with the wide variety of technologies and scales studied, but land-use efficiency of greenhouse gas savings and specific airborne emissions varied substantially. Also, while specific investment costs and electricity costs vary substantially from one system to another the number of jobs created per unit of electricity delivered remains roughly constant. Recorded views of stakeholders illustrate that diverging priorities exist for different stakeholder groups and this will influence appropriate choice of bioenergy systems for different applications

Renewable energy technology portfolio planning with scenario analysis: A case study for Taiwan

International Nuclear Information System (INIS)

Chen, T.-Y.; Yu, Oliver S.; Hsu, George Jyh-yih; Hsu, Fang-Ming; Sung, W.-N.

2009-01-01

This paper presents the results of a case study of applying a systematic and proven process of technology portfolio planning with the use of scenario analysis to renewable energy developments in Taiwan. The planning process starts with decision values of technology development based on a survey of society leaders. It then generates, based on expert opinions and literature search, a set of major technology alternatives, which in this study include: wind energy, photovoltaic, bio-energy, solar thermal power, ocean energy, and geothermal energy. Through a committee of technical experts with diversified professional backgrounds, the process in this study next constructs three scenarios ('Season in the Sun', 'More Desire than Energy', and 'Castle in the Air') to encompass future uncertainties in the relationships between the technology alternatives and the decision values. Finally, through a second committee of professionals, the process assesses the importance and risks of these alternative technologies and develops a general strategic plan for the renewable energy technology portfolio that is responsive and robust for the future scenarios. The most important contributions of this paper are the clear description of the systematic process of technology portfolio planning and scenario analysis, the detailed demonstration of their application through a case study on the renewable energy development in Taiwan, and the valuable results and insights gained from the application.

Workshop tools and methodologies for evaluation of energy chains and for technology perspective

Energy Technology Data Exchange (ETDEWEB)

Appert, O. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France); Maillard, D. [Energy and Raw Materials, 75 - Paris (France); Pumphrey, D. [Energy Cooperation, US Dept. of Energy (United States); Sverdrup, G.; Valdez, B. [National Renewable Energy Laboratory, Golden, CO (United States); Schindler, J. [LB-Systemtechnik (LBST), GmbH, Ottobrunn (Germany); His, St.; Rozakis, St. [Centre International de Recherche sur Environnement Developpement (CIRED), 94 - Nogent sur Marne (France); Sagisaka, M. [LCA Research Centre (Japan); Bjornstad, D. [Oak Ridge National Laboratory, Oak Ridge, Tennessee (United States); Madre, J.L. [Institut National de Recherche sur les Transports et leur Securite, 94 - Arcueil (France); Hourcade, J.Ch. [Centre International de Recherche sur l' Environnement le Developpement (CIRED), 94 - Nogent sur Marne (France); Ricci, A.; Criqui, P.; Chateau, B.; Bunger, U.; Jeeninga, H. [EU/DG-R (Italy); Chan, A. [National Research Council (Canada); Gielen, D. [IEA-International Energy Associates Ltd., Fairfax, VA (United States); Tosato, G.C. [Energy Technology Systems Analysis Programme (ETSAP), 75 - Paris (France); Akai, M. [Agency of Industrial Science and technology (Japan); Ziesing, H.J. [Deutsches Institut fur Wirtschaftsforschung, DIW Berlin (Germany); Leban, R. [Conservatoire National des Arts et Metiers (CNAM), 75 - Paris (France)

2005-07-01

The aims of this workshop is to better characterize the future in integrating all the dynamic interaction between the economy, the environment and the society. It offers presentations on the Hydrogen chains evaluation, the micro-economic modelling for evaluation of bio-fuel options, life cycle assessment evolution and potentialities, the consumer valuation of energy technologies attributes, the perspectives for evaluation of changing behavior, the incentive systems and barriers to social acceptability, the internalization of external costs, the endogenous technical change in long-tem energy models, ETSAP/technology dynamics in partial equilibrium energy models, very long-term energy environment modelling, ultra long-term energy technology perspectives, the socio-economic toolbox of the EU hydrogen road-map, the combined approach using technology oriented optimization and evaluation of impacts of individual policy measures and the application of a suite of basic research portfolio management tools. (A.L.B.)

Assessment of renewable energy potential. Calculation model “AREP-LP”

International Nuclear Information System (INIS)

Penchev, Alexander

2011-01-01

Introduction Bulgaria is a country rich in renewable energy sources. There are all types of RES including: solar, geothermal, biomass, wind energy and hydropower. Per capita it ranks among the top in Europe. Bulgaria's target for 2020 is 16% of final consumption of electricity should be from renewable energy. To achieve this goal, the first and most important task is assessing the potential of renewable energy and its geographical distribution. Creating a database of renewable energy is essential for implementation of investment projects in this area. Key words: Renewable Energy (RES), Renewable Technologies (RET), Theoretical Potential, Technical Potential, Municipalities, Regions, Energy Planning(EP), Emission Reduction (EmR), Market Assessment (MA), Data base(DB)

Evolutionary Patterns of Renewable Energy Technology Development in East Asia (1990–2010

Directory of Open Access Journals (Sweden)

Yoonhwan Oh

2016-07-01

Full Text Available This study investigates the evolutionary patterns of renewable energy technology in East Asian countries—Japan, Korea, and China—as an emerging technology where the catch-up strategy is actively taking place. To reflect the quality of technology development activities, we assess each country’s research and development (R&D activities using patent citation analysis. The goal of this study is to overcome the limitations of prior research that uses quantitative information, such as R&D expenditures and number of patents. This study observes the process of technological catch-up and leapfrogging in the East Asian renewable energy sector. Furthermore, we find that each nation’s technology development portfolio differs depending on the composition share of technologies. Policymakers in emerging economies can use the findings to shape R&D strategies to develop the renewable energy sector and provide an alternative method of evaluating the qualitative development of technology.

IEA Energy Technology Essentials: Biofuel Production

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-01-15

The IEA Energy Technology Essentials series offers concise four-page updates on the different technologies for producing, transporting and using energy. Biofuel Production is the topic covered in this edition.

IEA Energy Technology Essentials: Nuclear Power

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-03-15

The IEA Energy Technology Essentials series offers concise four-page updates on the different technologies for producing, transporting and using energy. Nuclear power is the topic covered in this edition.

IEA Energy Technology Essentials: Fuel Cells

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-04-15

The IEA Energy Technology Essentials series offers concise four-page updates on the different technologies for producing, transporting and using energy. Fuel cells is the topic covered in this edition.

Energy technology sources, systems and frontier conversion

CERN Document Server

Ohta, Tokio

1994-01-01

This book provides a concise and technical overview of energy technology: the sources of energy, energy systems and frontier conversion. As well as serving as a basic reference book for professional scientists and students of energy, it is intended for scientists and policy makers in other disciplines (including practising engineers, biologists, physicists, economists and managers in energy related industries) who need an up-to-date and authoritative guide to the field of energy technology.Energy systems and their elemental technologies are introduced and evaluated from the view point

Thermodynamic performance assessment of wind energy systems: An application

International Nuclear Information System (INIS)

Redha, Adel Mohammed; Dincer, Ibrahim; Gadalla, Mohamed

2011-01-01

In this paper, the performance of wind energy system is assessed thermodynamically, from resource and technology perspectives. The thermodynamic characteristics of wind through energy and exergy analyses are considered and both energetic and exergetic efficiencies are studied. Wind speed is affected by air temperature and pressure and has a subsequent effect on wind turbine performance based on wind reference temperature and Bernoulli's equation. VESTAS V52 wind turbine is selected for (Sharjah/UAE). Energy and exergy efficiency equations for wind energy systems are further developed for practical applications. The results show that there are noticeable differences between energy and exergy efficiencies and that exergetic efficiency reflects the right/actual performance. Finally, exergy analysis has been proven to be the right tool used in design, simulation, and performance evaluation of all renewable energy systems. -- Highlights: → In this research the performance of wind energy system is assessed thermodynamically, from resource and technology perspectives. → Energy and exergy equations for wind energy systems are further developed for practical applications. → Thermodynamic characteristics of wind turbine systems through energetic and exergetic efficiencies are evaluated from January till March 2010. → Exergy efficiency describes the system irreversibility and the minimum irreversibility exists when the wind speed reaches 11 m/s. → The power production during March was about 17% higher than the month of February and 66% higher than January.

The US Department of Energy hydrogen baseline survey: assessing knowledge and opinions about hydrogen technology

International Nuclear Information System (INIS)

Christy Cooper; Tykey Truett; R L Schmoyer

2006-01-01

To design and maintain its education program, the United States Department of Energy (DOE) Hydrogen Program conducted a statistically-valid national survey to measure knowledge and opinions of hydrogen among key target audiences. The Hydrogen Baseline Knowledge Survey provides a reference for designing the DOE hydrogen education strategy and will be used in comparisons with future surveys to measure changes in knowledge and opinions over time. The survey sampled four U.S. populations: (1) public; (2) students; (3) state and local government officials; and (4) potential large-scale hydrogen end-users in three business categories. Questions measured technical understanding of hydrogen and opinions about hydrogen safety. Other questions assessed visions of the likelihood of future hydrogen applications and sources of energy information. Several important findings were discovered, including a striking lack of technical understanding across all survey groups, as well as a strong correlation between technical knowledge and opinions about safety: those who demonstrated an understanding of hydrogen technologies expressed the least fear of its safe use. (authors)

Energy, environment and technological innovation

Directory of Open Access Journals (Sweden)

Fernando José Pereira da Costa

2015-08-01

Full Text Available The development problems can not be addressed without taking account of the environmental and energy issues, as well as the intimate relationship and the intense interaction between the two. In fact, the energy issue can not be analyzed separately from environmental issues, nor the advances in technological innovation, integrating dynamic-systemic way and so positioning address the issue of the development model to set the bulge the transition process experienced by the world since the seventies of the twentieth century. This transition, in turn, implies the passage of Paradigm of Fossil Fuels to Renewable Energy also called the Paradigm of renewable sources of energy, not just holding the energy problem, but towards to environmental and technological components. It is within this relatively slow and long process, instigator of high levels of volatility, turbulence inducing and motor of technological innovation, which is (re raises the question of the development model that defines how a new model/style development.

Electricity Generation in Fiji: Assessing the Impact of Renewable Technologies on Costs and Financial Risk

OpenAIRE

Dornan, Matthew; Jotzo, Frank

2011-01-01

In recent years, renewable energy technologies have been advocated in Fiji on the basis that they improve energy security and serve as a risk-mitigation measure against oil price volatility. Despite this, there have been few attempts to measure the impact of renewable technologies on energy security. That analysis is important if the benefits of renewable energy technologies in Fiji are to be adequately evaluated. This paper develops and applies a method for assessing the potential contributi...

Energy technology and American democratic values

Energy Technology Data Exchange (ETDEWEB)

Thompson, G.M.

1988-01-01

Today, the benefits of liberal democracy have increasingly been cast into doubt. The debate over alternative energy policies illustrates the problems associated with liberal democracy. For many, it is the realization that energy choices and the selection of social and political values amount to much the same thing. Simply put, energy policy decisions, and the concomitant energy technologies, carry implications of an ethical, social and political nature. The argument of the social and political effects of energy technology flows from the more general thesis that all forms of technological practice condition social and political relations. That is, technological systems, beyond performing the specific functions for which they were designed, act upon and influence social and political arrangements. Seen in this light, energy technologies are as important to the promotion and preservation of this country's political values as are its institutions and laws. Further, there is evidence to suggest that this country's cherished democratic value of freedom is slowly being eclipsed by the values attendant to corporate capitalism and its singular pursuit of growth. It is this dominance of economic values over political values which provides the environment within which the technological debate is waged. Ultimately, tracing the historic linkage between property and liberty, it is concluded that the preservation of our freedom require new thinking regarding the present configuration of ownership patterns. The questions surrounding energy policy serve to illuminate these concerns.

Energy Technology Programmes 1993-1998. Intermediate report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-01

The Tekes energy technology research programmes were launched in 1993. The aim is to produce innovative solutions that are efficient, environmentally sound and widely - even globally - applicable. Now Tekes manages a total of 12 energy technology research programmed. Research programmed form a network linking academia and industry. Total funding for the energy technology programmed during the years 1993-1998 is estimated at some FIM 1.5 billion, about half of which will be put up by the Tekes and the rest by the industry. Funding by the Ministry of Trade and Industry covers the first full-scale applications (demonstrations) resulting from the research and development activities. Finnish technology is front-ranking in the efficient use of energy, combustion technology, renewable energy sources and environmental technology. In this report the results and the research activities of the separate programmes is presented and discussed

Comparative risk assessment of severe accidents in the energy sector

International Nuclear Information System (INIS)

Burgherr, Peter; Hirschberg, Stefan

2014-01-01

Comparative assessment of accident risks in the energy sector is a key aspect in a comprehensive evaluation of sustainability and energy security concerns. Safety performance of energy systems can have important implications on the environmental, economic and social dimensions of sustainability as well as availability, acceptability and accessibility aspects of energy security. Therefore, this study provides a broad comparison of energy technologies based on the objective expression of accident risks for complete energy chains. For fossil chains and hydropower the extensive historical experience available in PSI's Energy-related Severe Accident Database (ENSAD) is used, whereas for nuclear a simplified probabilistic safety assessment (PSA) is applied, and evaluations of new renewables are based on a combination of available data, modeling, and expert judgment. Generally, OECD and EU 27 countries perform better than non-OECD. Fatality rates are lowest for Western hydropower and nuclear as well as for new renewables. In contrast, maximum consequences can be by far highest for nuclear and hydro, intermediate for fossil, and very small for new renewables, which are less prone to severe accidents. Centralized, low-carbon technology options could generally contribute to achieve large reductions in CO 2 -emissions; however, the principal challenge for both fossil with Carbon Capture and Storage and nuclear is public acceptance. Although, external costs of severe accidents are significantly smaller than those caused by air pollution, accidents can have disastrous and long-term impacts. Overall, no technology performs best or worst in all respects, thus tradeoffs and priorities are needed to balance the conflicting objectives such as energy security, sustainability and risk aversion to support rationale decision making. - Highlights: • Accident risks are compared across a broad range of energy technologies. • Analysis of historical experience was based on the

Bay of Fundy tidal energy : a response to the strategic environmental assessment

International Nuclear Information System (INIS)

2008-06-01

Tidal in-stream energy conversion is an emerging technology to harness sea power. These energy conversion devices are similar to underwater windmills. The government of Nova Scotia is interested in understanding the potential effects of these devices on the Bay of Fundy. As a result, it commissioned a strategic environmental assessment (SEA) that was completed in the spring of 2008. This document presented a response to the SEA. It discussed Nova Scotia's specific approach to tidal energy as well as the province's broader approach to marine renewable energy in the Bay of Fundy, with specific responses to each recommendation in the SEA. The energy context was presented, with particular reference to energy strategy; emissions; legal requirements; production costs; and carbon costs. The report also discussed tidal lagoon technology as well as a demonstration facility called the Fundy Tidal Energy Centre. The objectives of the SEA were also described and recommendations were presented. Recommendations were grouped under several key themes such as sustainability principles; allowing the demonstration of tidal in-stream energy conversion (TISEC) technologies; marine renewable energy legislation; research program; Mi'kmaq ecological knowledge study; provincial standard for ecological data; Bay of Fundy socioeconomic background study; marine renewable energy demonstration program; siting demonstration projects; and environmental assessment of the demonstration facility. figs

SIHTI - Energy and environmental technology

International Nuclear Information System (INIS)

Estlander, A.; Pietilae, S.

1993-01-01

The research and development program SIHTI was carried out during 1991-1992, mainly concentrating on energy and environmental technology. SIHTI focused on examining emissions from various sources of energy in all stages of the production chain. The objective was to create new methods and equipment, with which the environmental drawbacks of energy production can be reduced. Also a development work aiming at reduced traffic emissions was included in the program. Totally the program included 53 projects, which were divided into the following subsections: energy production, traffic, fuel chains and other projects. In the energy production projects the main attention was paid to reduction of sulphur dioxide, nitrogen oxide and particulate emissions. Furthermore waste utilization and possibilities of reducing carbon dioxide emissions were studied. The traffic study was focused on developing of more environmental-friendly liquid fuels. The research of emissions at low ambient temperatures was developed to an international level. Further the use of gases and the rape seed oil ester as traffic fuel was studied in practical tests. In the fuel chain study the emissions from the most important fuel chains were examined all the way from the purchase of the primary energy to the final end product. Methods for further reduction of water discharges from peat production were developed. The other projects were concentrated on modelling development, environmental impact assessment and emission surveys

System Energy Assessment (SEA, Defining a Standard Measure of EROI for Energy Businesses as Whole Systems

Directory of Open Access Journals (Sweden)

Jay Zarnikau

2011-10-01

Full Text Available A more objective method for measuring the energy needs of businesses, System Energy Assessment (SEA, measures the combined impacts of material supply chains and service supply chains, to assess businesses as whole self-managing net-energy systems. The method is demonstrated using a model Wind Farm, and defines a physical measure of their energy productivity for society (EROI-S, a ratio of total energy delivered to total energy expended. Energy use records for technology and proxy measures for clearly understood but not individually recorded energy uses for services are combined for a whole system estimate of consumption required for production. Current methods count only energy needs for technology. Business services outsource their own energy needs to operate, leaving no traceable record. That uncounted business energy demand is often 80% of the total, an amount of “dark energy” hidden from view, discovered by finding the average energy estimated needs for businesses far below the world average energy consumed per dollar of GDP. Presently for lack of information the energy needs of business services are counted to be “0”. Our default assumption is to treat them as “average”. The result is a hard measure of total business demand for energy services, a “Scope 4” energy use or GHG impact assessment. Counting recorded energy uses and discounting unrecorded ones misrepresents labor intensive work as highly energy efficient. The result confirms a similar finding by Hall et al. in 1981 [1]. We use exhaustive search for what a business needs to operate as a whole, tracing internal business relationships rather than energy data, to locate its natural physical boundary as a working unit, and so define a business as a physical rather than statistical subject of scientific study. See also online resource materials and notes [2].

Market penetration of energy supply technologies

Science.gov (United States)

Condap, R. J.

1980-03-01

Techniques to incorporate the concepts of profit-induced growth and risk aversion into policy-oriented optimization models of the domestic energy sector are examined. After reviewing the pertinent market penetration literature, simple mathematical programs in which the introduction of new energy technologies is constrained primarily by the reinvestment of profits are formulated. The main results involve the convergence behavior of technology production levels under various assumptions about the form of the energy demand function. Next, profitability growth constraints are embedded in a full-scale model of U.S. energy-economy interactions. A rapidly convergent algorithm is developed to utilize optimal shadow prices in the computation of profitability for individual technologies. Allowance is made for additional policy variables such as government funding and taxation. The result is an optimal deployment schedule for current and future energy technologies which is consistent with the sector's ability to finance capacity expansion.

How to count and assess different energies, in particular renewable energies: methodological reflections and examples

International Nuclear Information System (INIS)

Bacher, Pierre

2013-01-01

After having recalled the meaning of the concepts of primary energy and of final energy, as well as their relationships which are conventionally adopted at the international level, the author shows that these concepts are not suitable to the assessment of economic and energetic efficiency of energy systems, notably those comprising several transformations of an energy into another. He also shows that the methodology developed by the Academy of Technologies in its 'Vecteurs' report is perfectly adapted. This is illustrated by two examples: the main uses of biomass, and the use of peak productions of wind energy which is essentially intermittent. With this method, it is possible to identify the main factors which must be quantified when assessing the technical-economic relevance of such or such choice, notably thermodynamic efficiencies of each step, capitals to be invested and expectable load factors, or impact in terms of CO 2 emissions. Appendices proposes energetic statistics for France (energy assessment, consumption of primary energy), an assessment of methanization, and an analysis of wind energy production in Europe while taking its intermittency into account, for the production of hydrogen

Progress in Energy Storage Technologies: Models and Methods for Policy Analysis

Science.gov (United States)

Matteson, Schuyler W.

Climate change and other sustainability challenges have led to the development of new technologies that increase energy efficiency and reduce the utilization of finite resources. To promote the adoption of technologies with social benefits, governments often enact policies that provide financial incentives at the point of purchase. In their current form, these subsidies have the potential to increase the diffusion of emerging technologies; however, accounting for technological progress can improve program success while decreasing net public investment. This research develops novel methods using experience curves for the development of more efficient subsidy policies. By providing case studies in the field of automotive energy storage technologies, this dissertation also applies the methods to show the impacts of incorporating technological progress into energy policies. Specific findings include learning-dependent tapering subsidies for electric vehicles based on the lithium-ion battery experience curve, the effects of residual learning rates in lead-acid batteries on emerging technology cost competitiveness, and a cascading diffusion assessment of plug-in hybrid electric vehicle subsidy programs. Notably, the results show that considering learning rates in policy development can save billions of dollars in public funds, while also lending insight into the decision of whether or not to subsidize a given technology.

Learning in renewable energy technology development

International Nuclear Information System (INIS)

Junginger, M.

2005-01-01

The main objectives of this thesis are: to investigate technological change and cost reduction for a number of renewable electricity technologies by means of the experience curve approach; to address related methodological issues in the experience curve approach, and, based on these insights; and to analyze the implications for achieving the Dutch renewable electricity targets for the year 2020 within a European context. In order to meet these objectives, a number of research questions have been formulated: What are the most promising renewable electricity technologies for the Netherlands until 2020 under different technological, economic and environmental conditions?; To what extent is the current use of the experience curve approach to investigate renewable energy technology development sound, what are differences in the utilization of this approach and what are possible pitfalls?; How can the experience curve approach be used to describe the potential development of partially new energy technologies, such as offshore wind energy? Is it possible to describe biomass fuel supply chains with experience curves? What are the possibilities and limits of the experience curve approach when describing non-modular technologies such as large (biomass) energy plants?; What are the main learning mechanisms behind the cost reduction of the investigated technologies?; and How can differences in the technological progress of renewable electricity options influence the market diffusion of renewable electricity technologies, and what implications can varying technological development and policy have on the implementation of renewable electricity technologies in the Netherlands? The development of different renewable energy technologies is investigated by means of some case studies. The possible effects of varying technological development in combination with different policy backgrounds are illustrated for the Netherlands. The thesis focuses mainly on the development of investment

Profits or preferences? Assessing the adoption of residential solar thermal technologies

International Nuclear Information System (INIS)

Mills, Bradford F.; Schleich, Joachim

2009-01-01

Solar thermal technologies offer the potential to meet a substantial share of residential water and space heating needs in the EU, but current levels of adoption are low. This paper uses data from a large sample of German households to assess the effects of geographic, residence, and household characteristics on the adoption of solar thermal water and space heating technologies. In addition, the impact of solar thermal technology adoption on household energy expenditures is estimated after controlling for observed household heterogeneity in geographic, residential, and household characteristics. While evidence is found of moderate household energy expenditure savings from combined solar water and space heating systems, the findings generally confirm that low in-home energy cost savings and fixed housing stocks limit the diffusion of residential solar thermal technologies. Little evidence is found of differential adoption by distinct socio-economic groups.

Assessment of Emerging Renewable Energy-based Cogeneration Systemsfor nZEB Residential Buildings

DEFF Research Database (Denmark)

Carmo, Carolina; Dumont, Olivier; Nielsen, Mads P.

2016-01-01

Net Zero Energy Buildings (nZEB) imply reduced consumption by means of good insulation, passive strategies and highly efficient energy supply systems. Among others, micro cogeneration systems are considered as one of the system solutions with the highest potential to enable nZEB.These systems...... entail production of electricity and usable thermal energy (heat and/or cooling) to cover the energy demands of residential buildings, high energy efficiency levels and proximity of the energy source to the building. The concept of cogeneration is not new but the interest in smallscale cogeneration...... technologies based on renewable energy sources has increased tremendously in the last decade. A significant amount of experimental and modelling research has recently been presented on emerging technologies. In this paper, four main technologies are assessed: Fuel Cells (FC), Photovoltaic thermal (PV/T), solar...

Risoe energy report 9. Non-fossil energy technologies in 2050 and beyond

International Nuclear Information System (INIS)

Larsen, Hans; Soenderberg Petersen, L.

2010-11-01

This Risoe Energy Report, the ninth in a series that began in 2002, analyses the long-term outlook for energy technologies in 2050 in a perspective where the dominating role of fossil fuels has been taken over by non-fossil fuels, and CO 2 emissions have been reduced to a minimum. Against this background, the report addresses issues like: 1) How much will today's non-fossil energy technologies have evolved up to 2050? 2) Which non-fossil energy technologies can we bring into play in 2050, including emerging technologies? 3) What are the implications for the energy system? Further, Volume 9 analyses other central issues for the future energy supply: 4) The role of non-fossil energy technologies in relation to security of supply and sustainability 5) System aspects in 2050 6) Examples of global and Danish energy scenarios in 2050 The report is based on the latest research results from Risoe DTU, together with available international literature and reports. (Author)

Risoe energy report 9. Non-fossil energy technologies in 2050 and beyond

Energy Technology Data Exchange (ETDEWEB)

Larsen, Hans; Soenderberg Petersen, L. (eds.)

2010-11-15

This Risoe Energy Report, the ninth in a series that began in 2002, analyses the long-term outlook for energy technologies in 2050 in a perspective where the dominating role of fossil fuels has been taken over by non-fossil fuels, and CO{sub 2} emissions have been reduced to a minimum. Against this background, the report addresses issues like: 1) How much will today's non-fossil energy technologies have evolved up to 2050? 2) Which non-fossil energy technologies can we bring into play in 2050, including emerging technologies? 3) What are the implications for the energy system? Further, Volume 9 analyses other central issues for the future energy supply: 4) The role of non-fossil energy technologies in relation to security of supply and sustainability 5) System aspects in 2050 6) Examples of global and Danish energy scenarios in 2050 The report is based on the latest research results from Risoe DTU, together with available international literature and reports. (Author)

Cooperative technology development: An approach to advancing energy technology

International Nuclear Information System (INIS)

Stern, T.

1989-09-01

Technology development requires an enormous financial investment over a long period of time. Scarce national and corporate resources, the result of highly competitive markets, decreased profit margins, wide currency fluctuations, and growing debt, often preclude continuous development of energy technology by single entities, i.e., corporations, institutions, or nations. Although the energy needs of the developed world are generally being met by existing institutions, it is becoming increasingly clear that existing capital formation and technology transfer structures have failed to aid developing nations in meeting their growing electricity needs. This paper will describe a method for meeting the electricity needs of the developing world through technology transfer and international cooperative technology development. The role of nuclear power and the advanced passive plant design will be discussed. (author)

Emerging electrochemical energy conversion and storage technologies

Science.gov (United States)

Badwal, Sukhvinder P. S.; Giddey, Sarbjit S.; Munnings, Christopher; Bhatt, Anand I.; Hollenkamp, Anthony F.

2014-01-01

Electrochemical cells and systems play a key role in a wide range of industry sectors. These devices are critical enabling technologies for renewable energy; energy management, conservation, and storage; pollution control/monitoring; and greenhouse gas reduction. A large number of electrochemical energy technologies have been developed in the past. These systems continue to be optimized in terms of cost, life time, and performance, leading to their continued expansion into existing and emerging market sectors. The more established technologies such as deep-cycle batteries and sensors are being joined by emerging technologies such as fuel cells, large format lithium-ion batteries, electrochemical reactors; ion transport membranes and supercapacitors. This growing demand (multi billion dollars) for electrochemical energy systems along with the increasing maturity of a number of technologies is having a significant effect on the global research and development effort which is increasing in both in size and depth. A number of new technologies, which will have substantial impact on the environment and the way we produce and utilize energy, are under development. This paper presents an overview of several emerging electrochemical energy technologies along with a discussion some of the key technical challenges. PMID:25309898

Contribution of promoting the green residence assessment scheme to energy saving

International Nuclear Information System (INIS)

Huang, Zhiyu; Yuan, Hongping; Shen, Liyin

2012-01-01

Green residence development has been one of the important strategies for promoting sustainable urban development. Governments throughout the world have been encouraging property developers to deliver green properties. In line with this development, governments have been implementing various assessment programs to certify green residential buildings with the aim of contributing to sustainable urban development. With reference to the Chinese construction practice, this paper examines the effectiveness of the green residence assessment scheme toward its defined aim through investigating the contents and procedures of the green residence assessment scheme by referring to the practices of Chongqing city in western China. Based on the results of five case studies and five semi-structured interviews, this study reveals the significant contribution from implementing the green residence assessment scheme particularly to energy saving in residential buildings. Further, the green residence assessment scheme promotes the application of green building materials and green construction technologies in the entire process of delivering and operating residential buildings. The findings provide valuable references for further investigating alternative methods to achieve better energy saving in developing residential buildings. - Highlights: ► Energy saving in residence development is important for sustainable urban development. ► Green residence assessment scheme contributes significantly to energy saving in residences. ► Green residence assessment promotes application of environmentally friendly building materials and technologies

Information technology resources assessment

Energy Technology Data Exchange (ETDEWEB)

Stevens, D.F. [ed.

1992-01-01

This year`s Information Technology Resources Assessment (ITRA) is something of a departure from traditional practice. Past assessments have concentrated on developments in fundamental technology, particularly with respect to hardware. They form an impressive chronicle of decreasing cycle times, increasing densities, decreasing costs (or, equivalently, increasing capacity and capability per dollar spent), and new system architectures, with a leavening of operating systems and languages. Past assessments have aimed -- and succeeded -- at putting information technology squarely in the spotlight; by contrast, in the first part of this assessment, we would like to move it to the background, and encourage the reader to reflect less on the continuing technological miracles of miniaturization in space and time and more on the second- and third-order implications of some possible workplace applications of these miracles. This Information Technology Resources Assessment is intended to provide a sense of technological direction for planners in projecting the hardware, software, and human resources necessary to support the diverse IT requirements of the various components of the DOE community. It is also intended to provide a sense of our new understanding of the place of IT in our organizations.

Information technology resources assessment

Energy Technology Data Exchange (ETDEWEB)

Stevens, D.F. (ed.)

1992-01-01

This year's Information Technology Resources Assessment (ITRA) is something of a departure from traditional practice. Past assessments have concentrated on developments in fundamental technology, particularly with respect to hardware. They form an impressive chronicle of decreasing cycle times, increasing densities, decreasing costs (or, equivalently, increasing capacity and capability per dollar spent), and new system architectures, with a leavening of operating systems and languages. Past assessments have aimed -- and succeeded -- at putting information technology squarely in the spotlight; by contrast, in the first part of this assessment, we would like to move it to the background, and encourage the reader to reflect less on the continuing technological miracles of miniaturization in space and time and more on the second- and third-order implications of some possible workplace applications of these miracles. This Information Technology Resources Assessment is intended to provide a sense of technological direction for planners in projecting the hardware, software, and human resources necessary to support the diverse IT requirements of the various components of the DOE community. It is also intended to provide a sense of our new understanding of the place of IT in our organizations.

Defining the "proven technology" technical criterion in the reactor technology assessment for Malaysia's nuclear power program

Science.gov (United States)

Anuar, Nuraslinda; Kahar, Wan Shakirah Wan Abdul; Manan, Jamal Abdul Nasir Abd

2015-04-01

Developing countries that are considering the deployment of nuclear power plants (NPPs) in the near future need to perform reactor technology assessment (RTA) in order to select the most suitable reactor design. The International Atomic Energy Agency (IAEA) reported in the Common User Considerations (CUC) document that "proven technology" is one of the most important technical criteria for newcomer countries in performing the RTA. The qualitative description of five desired features for "proven technology" is relatively broad and only provides a general guideline to its characterization. This paper proposes a methodology to define the "proven technology" term according to a specific country's requirements using a three-stage evaluation process. The first evaluation stage screens the available technologies in the market against a predefined minimum Technology Readiness Level (TRL) derived as a condition based on national needs and policy objectives. The result is a list of technology options, which are then assessed in the second evaluation stage against quantitative definitions of CUC desired features for proven technology. The potential technology candidates produced from this evaluation is further narrowed down to obtain a list of proven technology candidates by assessing them against selected risk criteria and the established maximum allowable total score using a scoring matrix. The outcome of this methodology is the proven technology candidates selected using an accurate definition of "proven technology" that fulfills the policy objectives, national needs and risk, and country-specific CUC desired features of the country that performs this assessment. A simplified assessment for Malaysia is carried out to demonstrate and suggest the use of the proposed methodology. In this exercise, ABWR, AP1000, APR1400 and EPR designs assumed the top-ranks of proven technology candidates according to Malaysia's definition of "proven technology".

Adapting for uncertainty : a scenario analysis of U.S. technology energy futures

International Nuclear Information System (INIS)

Laitner, J.A.; Hanson, D.A.; Mintzner, I.; Leonard, J.A.

2006-01-01

The pattern of future evolution for United States (US) energy markets is highly uncertain at this time. This article provided details of a study using a scenario analysis technique to investigate key energy issues affecting decision-making processes in the United States. Four scenarios were used to examine the driving forces and critical uncertainties that may shape United States energy markets and the economy for the next 50 years: (1) a reference scenario benchmarked to the 2002 annual energy outlook forecast, (2) abundant and inexpensive supplies of oil and gas, (3) a chaotic future beset with international conflict, faltering new technologies, environmental policy difficulties and slowed economic growth, and (4) a technology-driven market in which a variety of forces converge to reshape the energy sector. Each of the scenarios was quantified using a computable general equilibrium model known as the All Modular Industry Growth Assessment (AMIGA) model. Results suggested that the range of different outcomes for the US is broad. However, energy use is expected to increase in all 4 scenarios. It was observed that the introduction of policies to encourage capital stock turnover and accelerate the commercialization of high efficiency, low-emissions technologies may reduce future primary energy demand. The analysis also showed that lower energy prices may lead to higher economic growth. Policies introduced to improve energy efficiency and accelerate the introduction of new technologies did not appreciably reduce the prospects for economic growth. Results also suggested that lower fossil fuel prices discourage investments in energy efficiency or new technologies and may mask the task of responding to future surprises. It was concluded that an investment path that emphasizes both energy efficiency improvements and advanced energy supply technologies will provide economic growth conditions similar to the implementation of lower energy prices. 11 refs., 1 tab., 2 figs

Competitive assessment of the US: Renewable energy equipment industry