WorldWideScience

Sample records for energy kenkyu kaihatsu

  1. NEDO Forum 2001. Session on development of geothermal energy (Prospect of geothermal energy); NEDO Forum 2001. Chinetsu kaihatsu session (chinetsu energy no tenbo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Director Noda of Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology, delivered a lecture entitled 'Future course of geothermal technology development,' and Executive Director Iikura of Tokyo Toshi Kaihatsu, Inc., a lecture entitled 'Thinking of geothermal energy.' Described in an achievement report entitled 'Present state and future trend of geothermal development' were the present state of geothermal power generation and characteristics of geothermal energy, signification of the introduction of binary cycle power generation, and the promotion of the introduction of ground heat utilizing heat pump systems. Stated in a lecture entitled 'Geothermal development promotion survey' were the geothermal development promotion survey and its result and how to implement such surveys in the future. Reported in a lecture entitled 'Verification survey of geothermal energy probing technology and the like and the development of geothermal water utilizing power plant and the like' were reservoir fluctuation probing, deep-seated thermal resource probing and collecting, 10-MW class demonstration plant, Measurement While Drilling System, and a hot rock power generation system. (NEDO)

  2. R and D on new energy technologies. Outlines of fiscal 1976 research results; Shin energy gijutsu kenkyu kaihatsu 1976 nendo kenkyu seika no gaiyo. Kenkyu kaihatsuhi kamihanki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-07-01

    This report outlines the results of (1) 8 researches on solar energy technology, (2) 4 researches on hydrogen energy, and (3) 4 general researches. (1) includes the prototype measuring instrument of near IR solar direct radiation using an interference filter to measure solar spectral irradiance, the prototype small-scale solar heat power model system, selective absorption and transmission films as solar heat power generation materials, InP solar cell and new solar cell system configuration, micro-wave power transmission of solar energy, and the expansion turbine using low-boiling point coolant for space power generation. (2) includes the hydrogen energy system, high-temperature thermolysis of water at 1,000 degrees C, prototype zirconia single-crystals for new solid electrolyte fuel cells, and the large-capacity high- temperature solid electrolyte fuel cell power system. (3) includes the total new energy system, the prototype superconducting magnet for energy storage, study on mechanism of an anomalous absorption effect by irradiation of strong laser beam onto high-temperature high-density ionized gas, and low-temperature difference power generation in the ocean. (NEDO)

  3. Research and development for solar thermal energy system. Research on advanced solar component; Taiyonetsu energy system no kenkyu kaihatsu. Kiki no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, T; Doi, T; Takashima, T; Ando, Y; Masuda, T; Fujii, T [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for research on advanced solar components as part of research and development of solar thermal energy. The catalyst for liquid-film reactions is prepared, and the flask tests are conducted as the preliminary experiments for development of the reactor in which 2-propanol is fallen in liquid film over the catalyst dispersed to accelerate its decomposition. It is decomposable when fallen in liquid film even in the presence of 35% of acetone. The catalyst of ruthenium carried by activated coal is used to produce 2-propanol under an exothermic condition from acetone and hydrogen. Diisopropyl ether and 4-methyl-2-pentanone are produced as by-products, when the reactor tube is kept at 140 to 200{degree}C at the external wall, diminishing as temperature is increased. There is a temperature differential of 20 to 30{degree}C in the reactor tube between the center axis and external wall. 3 figs.

  4. Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Development of energy use rationalization technology); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop self-complete type purification ceramic materials in which selection, separation, and purification functions are merged with the energy conversion function. Activities are conducted in the three fields of developing (1) materials derivation technology, (2) application technology, and (3) common base technology. In relation to selection, separation, and purification functions in field (1), studies are made about electrochemical cell structure control and cell constituting materials for enabling a high efficiency NOx purification reaction. As for the energy conversion function, studies are made about the improvement of characteristics of oxide based thermoelectric conversion materials and about changes in electrical output due to their development into cells. In a study of novel thermoelectric conversion materials, K{sub 2}NiF{sub 4} type Y{sub 0.33}Sr{sub 1.67}(Ni{sub 1-y}Co{sub y})O{sub 4-{sigma}} and Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 1-y}M{sub y})O{sub 4-{sigma}} (M=Fe, Co) are synthesized, and electrical resistivity levels and Seebeck coefficients are determined at room temperature-800 degrees C in an oxygen current. Seebeck coefficients are found to be negative for all specimens, which shows that they are n-type conductors. Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 0.7}Fe{sub 0.8})O{sub 4-{sigma}} exhibits the greatest output factor of 0.064 times 10{sup -4}Wm{sup -1}K{sup -2} (400 degrees C). (NEDO)

  5. Summary of research achievements in fiscal 1980 in research and development of new energy technologies (Research and development expense); Shin energy gijutsu kenkyu kaihatsu 1980 nendo kenkyu seika no gaiyo. Kenkyu kaihatsuhi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-07-01

    This paper describes the achievements in fiscal 1980 of new energy research at the General Research Institute of Electronics Technologies using the NEDO's development expense. To optimize the heat and electric power composite solar system, analyses were performed on heat production, devices and materials, and economy of the whole experimental facilities of the original model. Fundamental researches are being made on crystalline silicon, thin amorphous film and compound semiconductor solar cells. The solar thermionic generation element producing equipment installed in the previous fiscal year has produced and tested different types of electrodes, and operated the modules for an extended period of time. Measurement data of solar beam in ultraviolet, visible and near infrared zones were processed statistically, whereas the research work has been completed in the current fiscal year, having established successfully the reference solar radiation. In the hydrogen manufacturing technology using high-temperature direct pyrolysis, fundamental discussions were given on effects of electric and magnetic fields on dissociation of steam, and diffusion and separation of hydrogen by using permeation membranes. For hydrogen fuel cells, trial fabrication and tests were continued on single cells by using mainly the high frequency sputtering process. Experiments were continued on a solid electrolyte fuel cell system. Researches are under way as comprehensive study on such technological seeds as power generation using ocean temperature difference, and superconduction magnets for energy storage (NEDO)

  6. Report on the development/comprehensive research of new hydrogen energy demonstrative technology; Shinsuiso energy jissho gijutsu kaihatsu sogo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    In this project, the excess heat phenomenon caused by electrolyzing heavy water using palladium metal, etc. as electrode was captured as `new hydrogen energy.` To make a possibility of being as a future energy source clear, the abnormal heating phenomenon was verified. By elucidating the mechanism, the paper aimed at quantitatively controlling the heat generation. The R and D period was four years from fiscal 1993, and the details of the research are about the excess heat measuring test, material analysis/development tests, test on detection of reaction products, information collection/arrangement, international research cooperation. As a result of the research, a part of the excess heat measurement was surely able to be reproduced. However, when a confirmation experiment on the excess heat was conducted by another more positive method under the same conditions, it was found that the excess heat quantity was not the absolute excess heat quantity exceeding the measuring sensitivity/errors of the system. Supposing the excess heat of 0.1W order is generated in nuclear reaction, any of reaction products should be detected in a considerable quantity. However, no reaction products were not detected. 42 refs., 241 figs., 55 tabs.

  7. Fiscal 1997 report on the development of new hydrogen atomic energy demonstrative technology; 1997 nendo kenkyu hokokusho (shinsuiso energy jissho gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    In this validation study, phenomena of excess heat which are said to be generated by electrolysis of deuterium using palladium metal, etc. as electrode are taken as `new hydrogen atomic energy,` and to clarify a possibility of using them as a future energy source, the abnormal heating phenomenon was validated and the mechanism was elucidated. The study targeted quantitative control of heat emissions. The study was finished in 1997, the fifth year from the start. The excess heat measurement could partially be reproduced; however, when conducting a confirmation experiment on the excess heat by another more reliable method under the same condition, it was found that the value of excess heat was not an absolute value exceeding measuring sensitivity and errors of the system. If the excess heat of 0.1W order is to be emitted in nuclear reaction, any reactive product should be detected in a substantial quantity. However, the product of a large quantity was not found. A possibility was found out of an increase in nuclear reaction ratio inside solid by low energy deuterium irradiation. From the above, it was concluded that the use of new hydrogen atomic energy was negative. 20 refs., 149 figs., 29 tabs.

  8. Outline of geothermal energy research and development in fiscal 1999; Heisei 11 nendo chinetsu enerugi kenkyu kaihatsu no gaiyo

    Energy Technology Data Exchange (ETDEWEB)

    Konishi, T. [Agency of Industrial Science and Tehcnology, Tokyo (Japan)

    1999-11-18

    In this paper, the outline of the budget of geothermal energy relation in fiscal 1999, the system of research and development and the outline of research and development are described. Budgets in fiscal 1999 are the general account 17 million yen, the power development special account 3,222 million yen, sum total 323,900 million yen and it is a 33 million yen decrease compared with the preceding year. Within research and development, the following are included as a survey investigation research; a geothermal energy survey and picking technology, a verification investigation of a geothermal energy exploration technique, a deep geothermal resource investigation and an analysis and evaluation therefor. As a development of geothermal energy power plants using hot water, the following are included; development of the 10 MW binary cycle power generation plant, development of the bottom hole information system (MWD) in geothermal well drilling, technology development of the geothermal hot dry rock source system. As an analysis and evaluation of the bottom hole information detection system in geothermal well drilling, the following are included; an analysis and evaluation of the hot dry rock thermal extraction system, an analysis and evaluation of the deep geothermal resources picking technology, an analysis and evaluation of metallic materials for the geothermal deep direction and an analysis and evaluation of high polymer materials for the geothermal deep direction. (NEDO)

  9. Research and development of a high-temperature superconducting flywheel energy storage system. Research and development of the New Sunshine Program; Furaihoiru denryoku chozo shisutemu kenkyu kaihatsu. Nyu sanshain keikaku ni motozuku kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, Y. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1999-11-25

    The project conducted by NEDO for developing a high-temperature superconducting flywheel energy storage system is introduced; the two test results of fundamental studies are described. One is the measurement of levitation force and rotation loss of superconducting magnetic bearings composed of oxide superconducting bulks and permanent magnet composite. Two types of superconducting magnetic bearings. axial and radial types, were fabricated and tested. The other test was the fabrication and testing of two functional models. A small-sized superconducting flywheel model of the 0.5 kWh class was fabricated and tested. A medium-sized rotating functional model of the 10 kWh class was fabricated as well. (author)

  10. Fiscal 1997 report of the R and D result of industrial science and technology. R and D on synergy ceramics (development of rational energy use technology); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by transgranularly precipitating nano-size particles from a fine-grain high-density matrix through an improved particle formation process. Its toughness was considerably improved by controlling grain shape and grain boundary structure. A precipitation mechanism was also discussed. 89 refs., 107 figs., 14 tabs.

  11. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. Research on the construction of a web-based manufacturing system for the development of energy saving products; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Sho energy seihin kaihatsu no tame no web base seisan system no kochiku ni kansuru kenkyu (shonendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In Okinawa prefecture, the construction was proceeded with of the manufacturing industry of special aluminum sash (Tropical Sash) using a web-based manufacturing system. In the web-based manufacturing system, the flow related to the manufacturing information and materials (raw materials, parts, products) constitutes a network, which achieves energy conservation and increase in productivity by being connected simultaneously with technology, persons, makers, users and regions freely. Studies were made in the following three fields: 1) study on energy saving oriented products/energy saving processing technology (development of Tropical Sash); 2) R and D on the technology of the web-use concurrent manufacturing system; 3) development of the manufacturing technology using the open processing system. In 1), thermal insulation, air tightness and rigidity of special aluminum sash were evaluated to set up the basic shape of sections. In 2), themes were divided into those to be studied by the Okinawa group including the University of the Ryukyus and those by Mechanical Engineering Laboratory of Industrial Science and Technology. (NEDO)

  12. Fiscal 2000 survey report on R and D results of advanced clean energy vehicle; 2000 nendo kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With problems inherent to clean energy vehicles such as cruising distance, fuel supply and fuel consumption, ACEVs (advanced clean energy vehicles) are in demand featuring both low pollution and high efficiency compatibly. This paper explains the fiscal 2000 results of development. The target is, by using oil-alternative fuel, to reduce driving energy consumption and carbon dioxide emission to less than half and to control the life cycle cost (total of manufacturing cost, operating cost, fuel cost, etc.) to not more than twice as much as those of conventional vehicles. As ACEVs, an ANG (adsorbed natural gas) engine and flywheel battery mounted passenger car was selected, as were a CNG ceramics engine and capacitor mounted truck, CNG engine and lithium-ion battery mounted truck, LNG engine and capacitor mounted bus, and a DME engine and capacitor mounted bus. All are hybrid systems with an energy saving device. In the research of synthetic fuels, the results of the studies were summarized including the effect of various synthetic light oils on engine performance, fuel characteristics, effect of PM grain size and the optimum properties. (NEDO)

  13. Research and development project plans for FY 1995; 1995 nendo kenkyu kaihatsu jigyo keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    The present research and development project plans for FY 1995 administrated by NEDO consist of research and development of new energy, and research and development of industrial technology. Are illustrated further enhancement of new energy introduction promotion measures, new stage of international projects, promotion of new energy and new energy technology development, further enhancement of industrial and scientific technology research and development, integrated measures against global and urban environment problems, and budget of NEDO projects in FY 1995. The research and development of new energy includes coal conversion technology, solar energy technology, geothermal energy technology, energy conversion and storage technology, hydrogen, alcohol and biomass energy technology, geothermal energy resources, coal resources development, new energy promotion department activities, NEDO information center activities, and so on. On the other hand, the research and development of industrial technology includes research and development of industrial technology, and global environment technology. The research and development of industrial technology consists of superconductivity, new materials, biotechnology, electronics, information and communications, machinery and aerospace, natural resources, humanity, life and society, and various leading researches.

  14. Fiscal 1998 achievement report. Research and development of advanced clean energy vehicles; 1998 nendo kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The efforts aim to develop advanced clean energy vehicles (ACEVs) which drive on substitutes of oil low in pollution, consuming 1/2 or less energy and emitting 1/2 or less CO2 than the existing vehicles. Studies conducted in fiscal 1998 covered high-efficiency hybrid power systems and ACEVs. Efforts to develop ACEVs involved a reformed methanol fuel cell hybrid passenger car of Nissan Motor Co., Ltd. (improvement on element technologies, study of methanol concentration); CNG (compressed natural gas) engine hybrid passenger car of Honda Research and Development Co., Ltd. (improvement on flywheels, studies of ANG (adsorbent natural gas) adsorbent and ANG tank); CNG ceramics engine hybrid cargo truck of Isuzu Ceramics Research Institute Co., Ltd. (fabrication of ceramics single-cylinder engine, design and fabrication of vehicle control system, fabrication of prototype); CNG lean burn engine hybrid cargo truck of Mitsubishi Motors Co., Ltd. (studies, designing, and fabrication of engine element parts); LNG engine hybrid bus of Nissan Diesel Motor Co., Ltd. (development of engine and power storage); and DME (dimethylether) engine hybrid bus of Hino Motors, Ltd. (development of DME fuel injection system and high-efficiency power storage). (NEDO)

  15. Research and development of system to utilize photovoltaic energy. Survey on the evaluation of photovoltaic power generation; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoko hatsuden hyoka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on evaluation of PV power generation in fiscal 1994. (1) On the evaluation technique of energy pay-back time, foreign trial calculation examples by integration method were surveyed. However, there were not many study examples, and the calculation basis of input energy was also ambiguous. The calculation result by input-output analysis in Japan gave the value more than that by integration method, pointing out that indirect input energy is essential. (2) On the evaluation technique of the degree of environmental contribution, CO2 emission of the PV generation system installed on ordinary housing roofs was calculated to estimate reduction of CO2 emission and cost. As a result, PV power generation as reduction measures against CO2 brought a little cost increase. (3) On the latent scale of PV power generation, it was estimated to be nearly 191GW although under no restriction. It was a considerably large value as compared with the current power generation capacity in Japan. 4 tabs.

  16. Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Research and development of ultrahigh temperature gas turbine for power generation); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (hatsuden'yo chokoon gas turbine no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The fruits of fiscal 2000 efforts to develop high temperature energy materials and ultraprecision materials are briefly described. Activities are conducted in the four fields of (1) materials derivation and advanced evaluation/design technologies, (2) application technologies, (3) common base technologies, and (4) multifunction realization process evaluation. Discussed in field (1) are high temperature energy materials, high performance active materials, fundamental technologies for member designing, active materials for dealing with environmental gas, silicon based high resistance energy materials, porous multiple layer ceramic materials, macro-/micro-scale stress analysis technology, and microfracture analysis technology. Discussed in field (2) are heat resistant and damage tolerant materials, heat shielding materials and energy absorbing materials, and nanofilter materials capable of selective separation. In the study of active materials specific for environmental gas, a catalyst is developed, stable at high temperatures and capable of treating NOx selectively. The catalyst is a layered product comprising Ba hexaaluminate layers and stabilized zirconia layers. (NEDO)

  17. Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Research and development of ultrahigh temperature gas turbine for power generation); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (hatsuden'yo chokoon gas turbine no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The fruits of fiscal 2000 efforts to develop high temperature energy materials and ultraprecision materials are briefly described. Activities are conducted in the four fields of (1) materials derivation and advanced evaluation/design technologies, (2) application technologies, (3) common base technologies, and (4) multifunction realization process evaluation. Discussed in field (1) are high temperature energy materials, high performance active materials, fundamental technologies for member designing, active materials for dealing with environmental gas, silicon based high resistance energy materials, porous multiple layer ceramic materials, macro-/micro-scale stress analysis technology, and microfracture analysis technology. Discussed in field (2) are heat resistant and damage tolerant materials, heat shielding materials and energy absorbing materials, and nanofilter materials capable of selective separation. In the study of active materials specific for environmental gas, a catalyst is developed, stable at high temperatures and capable of treating NOx selectively. The catalyst is a layered product comprising Ba hexaaluminate layers and stabilized zirconia layers. (NEDO)

  18. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

  19. FY 1991 Report on research and development of super heat pump energy accumulation system. Construction and operation of the prototype system (Researches on systematization); 1981 nendo super heat pump energy shuseki system kenkyu kaihatsu seika hokokusho. System shisaku unten kenkyu (system ka kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    This research and development program includes the conceptual designs of and simulation studies on the super heat pump energy accumulation systems, to realize 30,000 kW-class commercial-scale plant. The district air conditioning and hot water supply by the plant of the above size are studied for the domestic area, including houses, office buildings, commercial facilities, and accommodations. The results indicate that the system has both merits and demerits, and should be further investigated for improvement. The merits include reduced power consumption by the heat pump, because of its high efficiency, reduction in the running cost, and increased ratio of late-night power, and the demerits include increased power consumption by the pumps for the heat source, increased initial costs of the facilities, and increased space-related cost. The industrial plants studied for application of the super heat pump energy accumulation system are those for production of corn starch, distilled sake and diary products. The other items studied include analysis/evaluation of economic distance for carrying heat source water, and improvement of simulator functions. (NEDO)

  20. Fiscal 2000 report on result of development project of marine resources utilization system for energy conservation. Development of marine resources utilization system for energy conservation (Model demonstrative research and basic study); 2000 nendo energy shiyo gorika kaiyo shigen katsuyo system kaihatsu jigyo seika hokokusho. Energy shiyo gorika kaiyo shigen katsuyo system kaihatsu (model jissho kenkyu oyobi kiban kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This paper explains the development of marine resources utilization system for energy conservation. The conceptual system is designed to take a large amount of deep sea water of 100 thousand to 1 million tons a day, to utilize it from the viewpoint of energy conservation using its coldness and purity characteristics, to then discharge it to the area of the sea in minimizing the environmental effect as well as obtaining effect such as absorption of carbon dioxide gas through cultivation of phyto-plankton. In pump-up technology, a piping system attaching on sea bed or floating with one or multiple constraints is applicable at present to all sites of geographical and oceanographic conditions. In utilization technology, use of deep-sea water as cooling water at a steam power plant, for example, improves generation efficiency by one point or more. In discharge and environment-related technologies, the research revealed that the deep-sea water from 300 m below releases carbon dioxide gas at surface, while photosynthesis can absorb the gas in the process of using nutrition contained in the deep-sea water; therefore, comprehensive examination is necessary taking energy utilization effect into account. Candidate sites were selected in areas of 200 m depth and within 5 km off-shore, with the optimum system examined at each site. (NEDO)

  1. Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

  2. Research and development of system to utilize photovoltaic energy. Survey on the specific purpose modules; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoto module ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on the specific purpose modules for photovoltaic power generation in fiscal 1994. (1) On the feasibility survey on new application fields, it was clarified that photovoltaic power generation is applicable to extensive areas such as farmland, road, railway and public facility as latent demand sites. (2) On the optimum modules for various specific purposes, the structure, production method, cost estimation and issues of various modules were studied for desert, wasteland, coast, ocean, river, embankment, railway, road, mobile facility and arcade. (3) On the survey on new materials and material development, various conventional materials and materials promising for required performance were surveyed for every application. (4) On the survey on technology trends, the survey members participated in the first international photovoltaic energy conversion conference and the photovoltaic power generation workshop, while the members held the 1st-5th specific purpose module subcommittees. 1 tab.

  3. FY 1998 result report. Research/development on the energy overall development/utilization technology of gas hydrate resource; 1998 nendo seika hokokusho. Gas haidoreto shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This study is aimed at studying for survey of gas hydrate (GH) deposit required for GH resource development and gathering of it, and further at studying for industrial utilization technology development of GH which is different in formation condition depending on kind of gas with which it reacts. The results of FY 1998 are as follows. In the study of the situation of existence of gas hydrate in the tundra, the sedimentary environment of the tundra where natural gas hydrate exists was simulated in laboratory to measure thermal conductivity of the sediments including GH. In this fiscal year, design/fabrication/calibration were conducted of the GH synthesizer and thermal analyzer. In the study of GH gathering technology in the tundra, a technology is discussed for recovering gas from GH layer and at the same time substituting CO2 hydrate for GH by blowing CO2 into the geologic layer. In FY 1998, formation/dissociation behaviors were first studied of methane/CO2 mixture hydrate. For the overall energy development of GH resource and promotion of R and D of the utilization technology, studies were made on physical properties of GH and development of the usage. (NEDO)

  4. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems (Development of practical technology for rational use of energy); 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of development of intelligent material/structure systems, study was made on practical technology for rational use of energy. For resource saving and energy saving (smartening) for large and complex machines and structure systems, light-weight long-life materials/structures are indispensable. Study was thus made on the basic technology of material/structure systems equipped with realtime defect detection function, structural integrity diagnosis function and control function of noise and vibration through information processing and control by integrating composite material/structure and fiber or film sensor material/device. For development of smartening technology, sensing technology was studied to detect the interior structure of composite material/structure compacts. The basic fabrication technology of ceramic actuator materials/devices, and shape memory alloy system actuators were put into development. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends for forming common knowledge. (NEDO)

  5. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. R and D of distributed power conditioner for photovoltaic power generation use; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Taiyoko hatsuden'yo bunsangata power conditioner no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    By developing 100W class micro-inverter and putting it to the solar cell panel one by one, a control system is developed by which the maximum output can be obtained as the solar cell system even if the output of individual panels changes by stain and shade. By this system, power generation efficiency is expected to be increased by approximately 10%. In case that power generation of 5 million kW is achieved in FY 2010, energy conservation of about 50,000 kl/year in oil conversion can be expected. In FY 2000, the following were carried out: 1) investigational study of electronic parts; 2) primary trial-fabrication of micro-inverter; 3) various kinds of simulation assuming the inverter parallel operation. In 1), two kinds using the fly-back transformer method and the immittance conversion theory were trial-fabricated. As to the former, the main circuit method was designed to be the fly back type high frequency insulation method, and the control method to be the pulse area modulation method. As to the latter, the current output type power converter was structured by the circuit simulation. (NEDO)

  6. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. R and D of distributed power conditioner for photovoltaic power generation use; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Taiyoko hatsuden'yo bunsangata power conditioner no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    By developing 100W class micro-inverter and putting it to the solar cell panel one by one, a control system is developed by which the maximum output can be obtained as the solar cell system even if the output of individual panels changes by stain and shade. By this system, power generation efficiency is expected to be increased by approximately 10%. In case that power generation of 5 million kW is achieved in FY 2010, energy conservation of about 50,000 kl/year in oil conversion can be expected. In FY 2000, the following were carried out: 1) investigational study of electronic parts; 2) primary trial-fabrication of micro-inverter; 3) various kinds of simulation assuming the inverter parallel operation. In 1), two kinds using the fly-back transformer method and the immittance conversion theory were trial-fabricated. As to the former, the main circuit method was designed to be the fly back type high frequency insulation method, and the control method to be the pulse area modulation method. As to the latter, the current output type power converter was structured by the circuit simulation. (NEDO)

  7. FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

  8. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

  9. Achievement report on industrial science and technology research and development in fiscal 2000. Research and development of synergy ceramics (Research and development of technology to prevent corrosion in petroleum production systems); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Achievements in fiscal 2000 were put into order for research and development of synergy ceramics aimed at completion of high temperature energy materials and ultra-precision materials. Activities were taken in the following four areas: 1) materialization technologies and advanced assessment and design technologies, 2) application technologies, 3) common basic technologies, and 4) assessment on composite function manifestation process. In Item 1), discussions were given on ultra-precision materials, high temperature energy materials, member designing basic technologies, materials to detect stress and microfine destruction, pore pattern controlling porous materials, and self-restoration and self-lubrication functioning materials. In Item 2), discussions were given on material and light selection functioning materials, high abrasion resistant and easy-to-process materials, high performance resistance materials for electric power devices, and flexible sliding materials. In the material and light selection functioning materials, their material selecting function was manifested by controlling micro pores through xerogelation on inorganic and organic hybrids. In the assessment of the composite function manifesting process, the wet type forming process was assessed, that uses microfine powder for model parts assuming cut members. (NEDO)

  10. Achievement report for fiscal 1998 on development of wide-area energy utilization network system. Eco-energy urban system (Research of systematization technology and evaluation technology out of energy system designing technology researches); Koiki energy riyo network system kaihatsu (eko energy toshi system) 1998 nendo seika hokokusho. Energy system sekkei gijutsu no kenkyu no uchi system ka gijutsu hyoka gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the realization of urban society respecting enhanced energy efficiency and environmental protection, cities and surrounding industrial facilities are investigated for the development of element technologies involving energy recovery, conversion, transportation, storage, delivery, utilization, etc., and for the compounding of urban energy systems. In the study of the effect of introduction, assumption is made of delivery of heat to an urban heat accumulation district from a plant equivalent to a district air-conditioning system which is covered by the existing technologies. Also assumed are the delivery of exhaust heat to the said plant utilizing eco-energy element technologies and the replacement of existing technologies by eco-energy element technologies. Comparison is established in terms of energy efficiency, environmental protection, and economy, and then it is found that the eco-energy element technologies for the utilization of exhaust heat are in all cases superior to the conventional technologies as far as energy efficiency and environmental protection are concerned. It is found, however, that they are inferior from the economic viewpoint. The energy efficiency technology in heat transportation is superior to the existing technology in energy efficiency and environmental protection but roughly equal to the existing ones in economy. (NEDO)

  11. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Final year report. Development of the measuring control technology supporting energy conservation in the manufacturing process of electronics (Design and trial manufacture of IMI); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Denshi kikirui seizo process no sho energy shien keisoku seigyo gijutsu no kaihatsu - IMI no sekkei to shisaku (saishu nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As measures taken for energy conservation in the manufacturing plant of electronic devices/equipment such as IC, the development was proceeded with a chlorine gas radio sensing system and a liquid crystal driver IC probe, according to the survey results that it is possible to control energy consumption in air conditioning by completely furnishing poisonous gas monitor in clean room and conserve energy related to the manufacture of IC and LSI tester by using Si for IC probe cards. The following four were carried out: 1) development/trial manufacture of chlorine sensing system; 2) development/trial manufacture of LCD (liquid crystal driver) IC probe; 3) support of trial manufacture of key element technology; 4) comprehensive investigational study of IMI (Intelligent Micro-Instrument). In FY 2000, study was focused on 1) and 2). In 1), a planar type micro-structure sensor was developed, and the trial-manufactured system brought favorable results in sensitivity, response speed and reproductivity. (NEDO)

  12. Research report of FY 1996 on development of new hydrogen energy demonstration technology. 1. FY 1996 results; 1996 nendo kenkyu hokokusho. Shinsuiso energy jissho gijutsu kaihatsu (1996 nendo jisshibun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    The purpose of this project is to clarify the possibility of new hydrogen energy as a future energy source. The new hydrogen energy is obtained from the excess heat generation phenomenon through the electrolysis of heavy water using palladium metal as an electrode. The excess heat regeneration tests have been successively conducted using two kinds of electrolytic cells. As a result, the excess heat generation measured by one electrolytic cell in FY 1996 has been confirmed in about 35% of repeatability under the same condition. On the other hand, the excess heat over the measuring accuracy was not measured using two kinds of absolute heating value measuring systems. The electrolytic cell, by which the excess heat was measured, was used for confirming the absolute heating value as keeping its condition. When tests were conducted using the developed system, it was found that the absolute heating value can not be detected. Then, verification tests are currently conducted for determining the cause. Moreover, in order to clarify the basic characteristics of materials required for the regeneration of the excess heat generation phenomenon, observation and analysis of the materials were performed before and after the excess heat measurement. Thus, the cause of difference was revealed. 3 refs., 98 figs., 24 tabs.

  13. FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

  14. Fiscal 2000 report on result of R and D on robot system cooperating and coexisting with human beings. Development of energy conservation technology; 2000 nendo ningen kyocho kyozongata robot system kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    Introduction of a number of robots and consumption of a large amount of energy are unavoidable if a complicated process operation is to be carried out by robots in an extensive work site. Great energy conservation is contrived by developing robots applicable to manufacturing in performing a variety of operations in place of human beings and thereby reducing the number of robots to work. This paper explains the fiscal 2000 results. For dual-handed cooperative tasks, a function was examined capable of gripping an object without giving a humanoid robot an instruction of an exact gripping position. A method was designed to prepare a command for the other arm through a command for one arm, with torque impedance control employed for the purpose of avoiding damage due to collision. A study was conducted on a three-dimensional shape detecting model using a visual device of a robot. In grasping problems of balance control of a humanoid robot, the behavior of a robot consisting of multi-links was considered as behavior of inverted pendulum, with possibility checked for the stabilization of the balance. For the purpose of putting the virtual robot platform previously developed to practical use, a three-dimensional operation tool of run-time user interface was developed, with research conducted on the sophistication of robot application. (NEDO)

  15. Development for environmentally friendly and highly efficient energy utilization system in fiscal 1998. Pt. 3. Research on highly efficient and effective energy utilization technology (Research on design technology for optimal system); 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 3. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper summarizes achievements during fiscal 1998 on researching part of the energy transportation and storage technologies, energy supply and utilization technologies, environmental load reducing technologies, and optimal system design in the 'research on highly efficient and effective energy utilization technology'. With regard to energy transportation and storage technologies, researches and developments were performed on a vacuum adiabatic transportation piping system, surfactants used for high-density heat transportation and high-density latent heat transportation technologies. In the field of energy supply and utilization technologies, researches and developments were carried out on a heat supply system using high-performance heat pumps capable of using multiple kinds of fuels, and a compression and absorption type hybrid heat utilization system. For the environmental load reducing technologies, research and development were performed on a power saving heat pump system utilizing natural coolant. In researching the optimal system design technologies, overall adjustment was made on the element technologies, whereas technological discussions and site surveys were executed by the committees at the same time. The latest achievements accomplished to date was published in a book. (NEDO)

  16. Research and development of evaluation system for photovoltaic power generation system. Research and development on evaluation technology of photovoltaic power generating systems; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. System hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of evaluation technology for photovoltaic power generating systems in fiscal 1994. (1) On preparation of test facility and measuring instrument, the pyrheliometer with a photovoltaic device as sensor was developed. (2) On collection and analysis of data, operation data of interconnection system, stand alone system, and water pump system were collected, and energy flow was analyzed. The following were also analyzed: time variation of a-Si solar cell modules, fluctuation correction factor of spectrum response, that of nonlinear response of crystalline solar cells, effect of solar radiation intensity and wind velocity on temperature rise of modules, and correction factor of DC circuit losses. (3) On on-site measurement technology, the array output measuring instrument was developed on the basis of capacitor charge system. (4) On simulation technology, simulation analyses of energy flow, optimum capacity of interconnection systems, correction factor of solar radiation, and capacity of array storage batteries were conducted. 3 figs., 6 tabs.

  17. Report on the results of the FY 1999 introductory R and D of MGC ultra-high efficiency turbine system technology. International cooperative project of MGC technology investigational study (R and D on advanced engine and energy saving use ceramics); 1999 nendo MGC chokokoritsu turbine system gijutsu sendo kenkyu kaihatsu seika hokokusho. MGC gijutsu chosa kenkyu kokusai kyoryoku jigyo (senshinteki engine oyobi sho energy yo yotoyo ceramics ni kansuru kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    As the R and D of advanced engine and energy saving use ceramics, this project is being conducted by the U.S., Germany, Sweden, Belgium and Japan under Annex II of the Committee of Energy Research Technology (CERT) established by International Energy Agency (IEA). For structure use ceramic materials, their raw material powder is tested and a method to evaluate characteristics of their sintered bodies is studied. The research was divided into Subtask 11 (test on mechanical characteristics) and Subtask 12 (evaluation of raw material powder). Each subtask decides on the details of the international joint research and the associated research assigned to each country. In the testing study on mechanical characteristics in this fiscal year, the evaluation method was studied of thermal characteristics of materials for heat resistant high temperature members. In the study for evaluation of raw material powder in this fiscal year, a method was studied for evaluation of characteristics of fine ceramic powder. The results to be obtained in this study are related to mechanical characteristics of materials for heat resistant high temperature members and to the basic evaluation method of characteristics of raw material powder. The results of the study are surely indispensable for promotion of the application of these materials. (NEDO)

  18. Fiscal 1974 Sunshine Project result report. R and D on solar heat power generation system (R and D on tower solar collection system); 1974 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. Tower shuko hoshiki system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-29

    This report summarizes the fiscal 1974 research result on the solar heat power generation system with a tower light collection system. This system receives solar radiation energy by reflector group, and concentrates solar energy reflected by each reflector on the heat absorber mounted on the top of the tower. A ratio of the whole reflector group area to the receiving area of the heat absorber is called a concentration factor. The heat absorber converts concentrated dense radiation energy to thermal energy, and transfers heated thermal medium to the bottom of the tower to supply solar heat to a thermal plant after appropriate treatment. Based on the above basic idea, study was made on the total system and each subsystem, and some problems on component equipment and materials were extracted. After solving these problems and improving the whole system accuracy, these results are put to practical use for design and operation of an actual pilot plant. The main research items are as follows: feasibility study, simulation, element study, preparation of a 10kWT test equipment, and planning of a 1,000kW class pilot plant. (NEDO)

  19. Achievement report for fiscal 1998 on area consortium research and development business, 1st year. Area consortium energy research and development (molding material processing eco-system using powder lubricant); 1998 nendo chiiki consortium energy kenkyu kaihatsu bun'ya. Funtai rikei junkatsuzai wo mochiita sokeizai kako eko system no kenkyu kaihatsu (dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A material processing technology demanding but low energy and cost and causing low environmental impact was developed using a powder lubricant in a closed metal die system. An inorganic powder excellent in adhesiveness as lubricant was discovered. Powder lubricants for die casting and new carbon lubricants for metal die forging were also developed. In a test in an eco-die casting system, it was found that power was better than water solution in terms of finish and energy efficiency. In the development of a metal forging system using a powder lubricant, existing graphite lubricants and new powder lubricants containing fullerene were subjected to evaluation (ring tests). Two types of graphite solutions now in use and two powder lubricants were evaluated by the ring tests, and this enabled the comprehension of powder lubricant characteristics. For the development of a die casting system requiring no lubricant, a metal die surface treatment method was found that produces a surface excellent in resisting erosion by the application of the aluminizing ion nitriding composite treatment method. In addition, wettability was compared between a PVD (physical vapor deposition)-formed nitride film and the powder lubricant constituents. The report also refers to surveys conducted for commercialization. (NEDO)

  20. Research and development of evaluation system for photovoltaic power generation system. Survey on research and development of solar cell evaluation system; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on R and D of solar cell evaluation systems in fiscal 1994. The performance/reliability evaluation subcommittee continuously analyzed technical issues and discussed solution measures from the last fiscal year. On development of performance evaluation methods, improvement of measurement accuracy for laminated solar cells is the study issue to be solved. Although laminated solar cells are measured by multiple light source solar simulator, difficult spectrum compensation causes measurement errors. Collection and analysis of data for determining atmospheric conditions, and outdoor measurement experiment under the atmospheric conditions for reference solar light were carried out. The study on incident angle characteristics of laminated solar cells clarified that the deviation from COS characteristics is 1.0% or less at an incident angle of 30{degree}. The study on generated energy in solar cell module level in field clarified that generated energy and generation efficiency are proportional to intensity of solar radiation. 1 tab.

  1. FY 1999 research and development results. Preparatory study for the underground thermal energy storage system; 1999 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    The study is conducted for the underground thermal energy storage system which utilizes heat capacity of the underground, e.g., aquifer, to exchange heat with the underground, and the FY 1999 results are described. For establishment of the concept of the underground heat storage systems, 2 sites are selected for each of Tokyo, Osaka and Sapporo for the study as the geological ground models, for their weather characteristics. Two cases are considered for the site where underground heat exchangers are installed, open space and immediately below a building. The heat-storage system comprises a high-efficiency heat pump, water heat-storage tank and cooling tower. The evaluation results indicate that energy saving rate of 37% or more and CO2 reduction rate of 9.5% or more are achievable in all areas except Sapporo, i.e., Tokyo and Osaka. The economic evaluation results indicate that the simple pay-out period is around 100 years for Tokyo and Osaka, and 80 years for Sapporo. The underground heat storage system is approximately 10% lower in life-cycle cost than the conventional system, 3 versus 3.3 billion yen for the period of 60 years. (NEDO)

  2. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D of new technology using low temperature energy for storage of agricultural products (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / teion energy wo riyoshita nosanbutsu no shinki chozo gijutsu no kenkyu kaihatsu (daiichi nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The development was conducted of a new technology using low temperature energy in Hokkaido for storage of agricultural products. In this fiscal year, the R and D were conducted of 1) elucidation of behavior of water droplets in the air at below-freezing temperatures and technology to preserve agricultural products, 2) low temperature region high efficiency energy conversion application technology, and 3) latent heat cold storage technology. In 1), it was clarified that the electrostatic capacity system is appropriate as non-contact simple measuring device of moisture distribution in cold air. Freezing temperatures were measured of potatoes, onions and carrots produced in Hokkaido. Equipment to generate moist air at below-freezing temperatures was trially manufactured which is composed of humidifier and freezer. A relation was studied between the humidifying method and the size of particulate water droplet. In 2), an experimental device was trially fabricated of BiTe thermoelectric conversion device. An experimental device for Stirling engine power generation was assembled which was incorporated into the waste incinerator. A basic experimental device of pulse pipe refrigerator was trially fabricated. Single crystals of BiSb semiconductors were made. In 3), it was clarified that gas hydrates of CO2 and C3H8 are promising as refrigerant. 60 refs., 120 figs., 19 tabs.

  3. Worldwide clean energy system technology using hydrogen (WE-NET). Interim report of the research and development in Phase 1; Suiso riyo kokusai clean energy system gijutsu (WE-NET). Daiikki kenkyu kaihatsu chukan seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-01

    Large scale and effective utilization of renewable energy including hydroelectric power, photovoltaic power, and wind power which are abundant on the earth can contribute to the solution of global environmental issues as well as the release of energy demand and supply. Hydrogen can be produced from the renewable energy, and is converted, transferred and stored if necessary. Such hydrogen can be used in various fields for power generation, fuel for transport, and city gas. In order to establish the technology by which worldwide energy network can be introduced for wide range of fields, conceptual design of a total system has been conducted, and elemental core technologies have been developed. Conceptual design of a practical scale system (total system) including a wide range from production of hydrogen to its utilization has been conducted, and its constitution has been illustrated. In addition, the energy balance and cost of hydrogen have been calculated and analyzed as a trial. Hydrogen production technology, transport and storage technology, and hydrogen utilization technology are introduced as individual elemental technologies. Research results of innovative and leading technologies obtained in FY 1996 are reviewed. 80 figs., 56 tabs.

  4. Research and development of utilization technology of solar thermal system for industrial and other use. Development of passive solar system (research and development of advanced glazing); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Passive solar system no kaihatsu (chokozai nado no kenkyu kaihatsu (advanced grazing no kenkyu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for advanced glazing in which solar energy is efficiently utilized. The peripheral techniques are surveyed for evaluation of characteristics of large-size dimming glass, optimization of film compositions and scaling up. The dimming device, made on a trial basis, attains a target controllable rage of at least 50% for visible light transmittance. The suitable components include WO3 as the electrochromic material producing color under a reducing atmosphere, NiO as the counter electrode producing color under an oxidative atmosphere, and hydrated SbOx as the proton-conducting electrolyte. The test results indicate possibility of the dimming glass stably operable while being irradiated with a quantity of sun ray of around 10 years. The study on scaling up the dimmer glass develops, on a trial basis, a process for producing large-size glass and evaluates its characteristics, where the film parameters are investigated. It also investigates the peripheral techniques for assembling the devices for the large-size glass, and develops useful techniques, such as those for sealants and improved sealing methods. 1 fig., 1 tab.

  5. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Third year report. Ultra-high density information storage component; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Chokomitsudo joho storage component (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of industrially creating next generation HDD (hard disk drive), the development was proceeded with of ultra-high density and energy saving type next generation HDD system. The following four were conducted: 1) development of active type magnetic head arm for high speed writing/reading-out; 2) development of ultra-smooth low-noise medium using ultra-clean process; 3) establishment of component technology of high efficiency lubricating materials; 4) development of reproductive magnetic head using TMR device. TMR device is an ultra-high sensitivity magnetic detecting device composed of three layers of ferromagnetic material/insulator/ferromagnetic material. As to the development of regenerative magnetic head, studies were made of the reduction in resistance of TRM device, fabrication of submicron device and system integration. For the development of low resistance TMR device, thickness of Al layer, oxidation conditions and heat treatment conditions were studied in detail. The tunnel joining was obtained in which RA value and TMR ratio are 80 ohm(center dot){mu}m{sup 2} and 30%, respectively, in case of the thickness of Al layer of 6.6 (angstrom). (NEDO)

  6. Report of the results of the fiscal 1997 survey. R and D of high efficiency clean energy vehicles; 1997 nendo chosa hokokusho. Kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing an automobile which keeps low pollution using petroleum substituting clean energy, decreases the running energy consumption to a half at least, and reduces the CO2 emission to less than a half of the conventional one at the same time, the R and D started in fiscal 1997. As to the study of a high efficiency hybrid power system, conducted were the prediction of fuel consumption performance of the system proposed, evaluation of element technology using hybrid simulator, evaluation experiment on a new hybrid vehicle, and grasp of overseas trends. In relation to the development of hybrid vehicles, the following were studied: methanol fuel cell loading hybrid vehicle, CNG engine loading hybrid vehicle, CNG ceramic engine loading hybrid truck, CNG lean burn engine loading hybrid truck, LNG engine loading hybrid bus, and DME engine loading hybrid bus. Besides, a survey on synthetic fuel and the related survey were carried out. 17 refs., 185 figs., 101 tabs.

  7. Report on achievements in fiscal 1999. Research and development of synergy ceramics (research and development of ultra-high temperature gas turbine for power generation); 1999 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho. Hatsuden'yo chokoon gas turbine no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research and development has been performed on the following themes: (1) high-temperature energy materials, (2) high-function active materials, (3) fundamental member material design technologies, (4) materials to activate specific environmental gases, (5) energy materials having high resistance to silicon groups, (6) porous multi-layer ceramic materials, (7) micro and macro applied analytic technologies, and (8) microscopically destructive analysis technologies. In Item 1, investigations were performed on the relationship of micro columnar particle structure of porous silicon nitride bodies with strength and destruction energy to identify the mechanism for manifestation of these characteristics. In Item 2, catalyst and electrode materials having the selectively separating and cleaning functions were developed, and materials to convert oxides thermo-electrically having high characteristics were discussed. In Item 3, polycrystalline alumina, polycrystalline zirconia, and zirconia particle dispersed alumina were fabricated on the trial basis to give them microscopic and macroscopic evaluations. In Item 4, crystalline hexa-aluminates in single phase were synthesized successfully. In Item 5, a synthesizing experiment was carried out on Ca-{alpha} sialon powder to evaluate and analyze the configuration phase of the product and the particle patterns. In Item 7, the homogenizing method was used to develop a three-dimensional program to analyze the correlation between the microscopic non-homogeneous structure and the macroscopic properties of synergy ceramics. In Item 8, the basic dimensions of porous alumina bodies were discussed based on energy density. (NEDO)

  8. FY 1998 report on the R and D of the industrial science technology. R and D of synergy ceramics; 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Hazardous ingredients in gases exhausted from diesel, refuse treatment facilities, etc. are becoming the problem. The development is expected of porous ceramic films which have functions of separation/purification at high temperature. By making good use of the technology to synthesize ceramic films with uniform through pores of several ten nm order and the technology to form 1D through pores of several ten - 100{mu} m order, the development of the following technologies were made and are in sight: enhancement of functions of gas separation/purification, function of catalyst-carrying to be given, porous film formation/base material fabrication. For the commercialization of high performance structure use ceramic parts, required is innovation of the production method by which the production cost is reduced without damaging the characteristics. Technologies were used of micro-fine raw materials, rapid sintering, texture assessment, analysis, etc., and study was made of cost reduction in high performance ceramic parts. For energy conservation by reducing the sintering temperature, the following were trially conducted: mechanical ironing, use of low grade raw material, use of superplastic reformation and forging, etc. (NEDO)

  9. Development for environmentally friendly and highly efficient energy utilization system in fiscal 1998. Pt. 1. Research on highly efficient and effective energy utilization technology (Research on design technology for optimal system); 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 1. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper summarizes achievements of the researches during fiscal 1998 on researching a highly efficient and effective energy utilization technology. With regard to technologies to recover and convert unutilized energies, a process simulator was developed, basic internal structure was discussed by experiments and simulation, and substance migrating and heat exchanging characteristics were identified by using partial testing devices. These researches and developments were performed for the waste heat reforming and recovering systems used in chemical plants. In developing a thermoelectric generation system using low calorie exhaust gases, thermoelectric power generating materials were developed, a powder manufacturing technology was developed, a thermoelectric conversion element bulking technology was developed, a thermoelectric power generation system using porous structures was simulated, development and concept design were carried out on system element technologies. In the research and development of the thermoelectric generation system using low calorie exhaust gases, advanced materials and modules were manufactured, the modules were evaluated, and power generation systems were researched. In addition, researches were performed on energy transportation, supply and utilization technologies, and on environmental load reducing technologies. (NEDO)

  10. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (Development of technologies for rational use of energy); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, as part of development of technologies for rational use of energy. The program for development of health monitoring technologies produces the bright prospects for commercialization of the fine FBG (Fiber Bragg Grating) sensor which can be embedded in a CFRP prepreg, and establishes the crack detecting method. The program for development of smart manufacturing technologies describes the dielectric constant sensor capable of monitoring the curing process, detection of the cured conditions by the optical fiber sensor, and development of the performs by RTM (Resin Transfer Molding). The program for technological development of the active-adaptive structures conducts the vibration- and noise-controlling tests for the small-size structural elements, confirming that the damping coefficient is improved by at least 20% and acoustic power is reduced by at least 30%. The program for developing the actuator materials and elements improves the piezoelectric characteristics of the PZT-based materials by hybrid sintering, and develops the actuators of high-durability FGM (Function-Gradient Materials). It also develops the foil- and belt-shaped shape memory alloys by arc-aided dissolution and rapid solidification of Ti-Ni-Cu-based alloys. (NEDO)

  11. FY 1977 Annual report on Sunshine Project results. Research and development of solar energy systems for air conditioning and hot water supply (Research and development of systems for large buildings); 1977 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Ogata kenchikubutsuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-31

    This project is aimed at development of (1) devices for solar energy systems for air conditioning and hot water supply, and (2) low-cost, safe systems incorporating the above devices, which are easily inspected and maintained, in which optimum buildings for effective utilization of solar energy are also investigated. Precision of the system analysis is improved by feeding back the results obtained by the basic studies conducted so far into the simulation. The technical supports for commercialization of heat collectors, refrigerators, heat-storage tanks and radiation type ceilings are also obtained. These results are combined for the designs of a real-size test building. In this year, works to install the facilities in the Oita University's test building are completed. These facilities include 40 units of large-size heat collectors (each approximately 2 m by 7.5 m in size); an absorption refrigerator of 30 uSRT in which single- and double-effect systems are combined; 2 piston-flow type heat-storage tanks, each 45 m{sup 3} in capacity; and others including analyzer, associated piping, duct, instrumentation and electrical systems. The test runs are conducted for the control systems, and long- and short-term instrumentation systems to draw the test schedules for optimizing the full-scale runs to be conducted in the next year. The operating and instrumentation manuals, and operating schedules are also drawn. (NEDO)

  12. Fiscal 1999 achievement report. Development of technology for machine tool with energy consumption rationalized (Research and development of environment-conscious grinding system); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Kankyo taiogata kensaku kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A large quantity of coolant is used in the grinding process for ensuring high accuracy and quality in the work. This presents a serious problem from the viewpoint of environmental impact or energy conservation, and now environment-conscious grinding methods requiring no or less coolant are sought for. With a view to answering the demand, efforts are exerted to put to practical use, and improve, an EcoloG grinding technique. The goal is to reduce to half the energy that the grinding process is now consuming. The EcoloG technique is a grinding method under which vegetable oil mist is cooled for lubrication and a small amount of cooling water is fed to the point of grinding for removing chips. In fiscal 1999, a survey was conducted on technical literature, patents, and the like in and out of Japan for the study of the actual state of dry machining, and then the course of future studies was clearly established. Studies were also carried out aiming at the practical application and improvement of the EcoloG grinding technique, and the technique achieved a quality level as high as that of the conventional coolant-aided method in a process of grinding a shaft to have an accurate outer diameter by use of an ordinary wheel head. (NEDO)

  13. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use; 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa itaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper analyzes and puts into order the data surveyed and discussed on thirteen Welfare Techno-Houses (WTH) from a comprehensive viewpoint. It summarizes findings contributing to development and structuring of new at-home welfare device systems of effective energy utilization type. The paper first puts into order and discusses the survey and study items available for comparison and discussion, and the survey items with originality found in the surveys of the WTH, with which relatively large number of items were surveyed and studied among the thirteen locations nationwide. Next, the paper attempts comprehensive evaluation on the achievements thereof by the following items: (1) measurement and evaluation on energy consumption of different at-home welfare devices, (2) surveys and studies on energy demand evaluation inside and outside the residential houses arranged with considerations for elderly people according to the district characteristics, (3) evaluation on daily, weekly and annual changes in energy consumption in these houses, and (4) design and development of welfare systems of effective energy utilization type for these houses. Furthermore, the paper summarizes the general attributes of the WTHs in different districts, power consumption in these at-home welfare device systems in the WTH and energy consumption of the houses, in the forms available for comparison and discussion. Then, the paper summarizes the achievements of the present surveys and studies on the thirteen WTHs all over the country. (NEDO)

  14. Survey of the development of an energy use rationalization home welfare apparatus system. Report on results of the research under consignment; 1996 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa itaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper analyzed characteristics of structures of houses considered of aged people, characteristics of use of home welfare apparatus, etc. and investigated/studied energy effective use type home welfare apparatus systems. As to the energy assessment of home welfare apparatus, measurement/evaluation of the energy consumption were conducted in the state of the use according to shapes of life/action of aged people/people needing care in terms of electric-driven bed, care lift, electric-driven wheel chair, etc. Concerning the assessment on energy demand in houses considered of aged people in accordance with regional characteristics, three welfare technohouses were used. In Sapporo, Hokkaido, conducted were evaluation of the present situation of indoor environment and the energy demand, the snow disposal problem at the approach and the energy demand assessment on road heating, etc. In Kamogawa, Chiba prefecture, a research study was made of factors of the increasing energy consumption caused by the use of care apparatus. In Shiga prefecture, an analytical study was carried out of biological effects of the thermal environment in home care houses on aged people, etc. 21 refs., 341 figs., 70 tabs.

  15. FY 1986 Report on research and development of super heat pump energy accumulation system. Part 1. Development of elementary techniques; 1986 nendo super heat pump energy shuseki system no kenkyu kaihatsu seika hokokusho. 1. Yoso gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-04-01

    Summarized in detail herein are R and D results of the super high performance heat pumps and elementary equipment and working fluids, for R and D of the super heat pump energy accumulation system. For R and D of the super high performance compression heat pumps, the R and D efforts are directed to development of new working fluids, high-performance heat exchangers, closed motors and so on for the highly efficient type (for heating only); to researches on mixed coolants, high-efficiency screw compressors and so on for the highly efficient type (for cooling and heating); to development of tooth shape of the screw compression section, surveys on thermal stability of the working fluids for heating and so on for the high temperature type (utilizing low temperature heat source); and to R and D of the high-speed reciprocating compressors and steam superchargers for the high temperature type (utilizing high temperature heat source). For R and D of the elementary equipment and working fluids, researches are conducted on evaporators for mixed working fluids, condensers utilizing the EHD effect, stainless steel plate fin type heat exchangers, heat exchangers for the chemical heat accumulation unit, and so on. The R and D efforts are also directed to the working fluids (alcohol-based and nonalcohol-based). (NEDO)

  16. Survey and research achievement report for fiscal 1980 on patent and information under Sunshine Program. Survey of information on new energy technology development (Solar energy); 1980 nendo tokkyo joho chosa kenkyu seika hokokusho. Shin energy gijutsu kaihatsu joho chosa (taiyohen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Solar energy as defined by the United States includes hydroelectric power, biomass, and the ocean. The short-term strategy deals with passive solar air-conditioning, hydroelectric power, and biomass direct combustion. The medium-term strategy involves positive heating and wind power. The long-term strategy covers heat for agriculture, photovoltaic power, and OTEC (ocean thermal energy conversion), and the ultralong-term strategy covers power generation in space and photochemical conversion. Canada is behind other countries in the conversion of solar energy into power, and solar energy is used but passively as heat source, this because this country is rich in other resources. In West Germany, solar energy may be exploited for hot-water supply and heating at high latitudes, but it is not likely that it will be used for power generation. Home heating offers some appeal since potential demand for it is great. In Britain, the use of solar energy is not a pressing matter, this because systems for effective use of coal have long been established at homes, society, and industries in this country, rich in coal resources and enjoying oil from the North Sea oil field. France's efforts include biomass exploitation. In its development efforts, importance is attached to home heating, hot-water supply, and biomass. Next comes the conversion into power of solar energy. Photocells are also a subject of research and development. (NEDO)

  17. Survey and research achievement report for fiscal 1980 on patent and information under Sunshine Program. Survey of information on new energy technology development (Solar energy); 1980 nendo tokkyo joho chosa kenkyu seika hokokusho. Shin energy gijutsu kaihatsu joho chosa (taiyohen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Solar energy as defined by the United States includes hydroelectric power, biomass, and the ocean. The short-term strategy deals with passive solar air-conditioning, hydroelectric power, and biomass direct combustion. The medium-term strategy involves positive heating and wind power. The long-term strategy covers heat for agriculture, photovoltaic power, and OTEC (ocean thermal energy conversion), and the ultralong-term strategy covers power generation in space and photochemical conversion. Canada is behind other countries in the conversion of solar energy into power, and solar energy is used but passively as heat source, this because this country is rich in other resources. In West Germany, solar energy may be exploited for hot-water supply and heating at high latitudes, but it is not likely that it will be used for power generation. Home heating offers some appeal since potential demand for it is great. In Britain, the use of solar energy is not a pressing matter, this because systems for effective use of coal have long been established at homes, society, and industries in this country, rich in coal resources and enjoying oil from the North Sea oil field. France's efforts include biomass exploitation. In its development efforts, importance is attached to home heating, hot-water supply, and biomass. Next comes the conversion into power of solar energy. Photocells are also a subject of research and development. (NEDO)

  18. Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on large-size energy supply system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (ogata energy kyokyu system no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to propose large-size system development scenarios assuming installations in deserts, the following investigations have been carried out: (1) collection of data on societies, economy, and energies in China and other countries where the large systems are assumed to be installed, (2) in order to reduce the costs, comparison was given on power generation cost by using a fixed tracking frame, a single axial tracking frame, and a biaxial tracking frame, (3) in order to evaluate the life cycle, discussions were given on the required energy inputs for system equipment, transmission and transformer equipment, and the installation construction to estimate the energy payback time (EPT) and CO2 emission unit requirement, and (4) discussions on development scenarios. In Item (1), while China expects on natural gas and atomic energy as the supply source, 80% of the energy would be supplied from coal in 2010. The development of new energies in India would further be delayed than in China. In item (2), the trially calculated power generation costs in Mongol by using the fixed frame, single axial tracking frame, and biaxial tracking frame were 8.72, 8.23 and 6.94 yen per watt. In Item (3) The EPT was two years or less in a 100-MW system, and the CO2 emission unit requirements in the silicon systems were 10 to 19 kg-C/kWh. (NEDO)

  19. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

  20. Achievement report for fiscal 1998 on development of wide-area energy utilization network system. Study of energy system designing technology (Research into factory area energy system); Koiki energy riyo network system kaihatsu, energy system sekkei gijutsu no kenkyu 1998 nendo seika hokokusho. Kojogun no energy system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Actualities of exhaust heat and demand for heat in the area are investigated on the result of which a wide-area energy utilization network system will be built. In fiscal 1998, further questionnaires are distributed in addition to last fiscal year's, and door-to-door visits are made on leading factories representing 10 types of industries. The result of data analysis places the nationwide total of exhaust heat at 320,000 Tcal/year including heat generated by electric power generation. When it is so defined that usable heat be above 150 degrees C for exhaust gas, above 40 degrees C for hot water, and above 200 degrees for solids, the total will be reduced to 230,000 Tcal/year. Cleaning plants (plants that treat refuse or sewage) as the sources of exhaust heat besides the factories are investigated for the amount of heat they discharge, and then it is found that the amount of heat they discharge is the fourth largest following electric power plants, iron and steel mills, and chemical plants. It is also found that most of their exhaust heat is of good quality because it is latent in steam or hot water. It is acknowledged, partly because many of such plants are situated relatively near to the urban district, that their role is important when studies are made on the utilization of exhaust heat. (NEDO)

  1. Fiscal 1997 report of the R and D result of industrial science and technology. R and D on synergy ceramics (R and D on an ultrahigh-temperature gas turbine for power generation); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (hatsuden`yo chokoon gas turbine no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For development of high-efficiency power generation gas turbines using petroleum substituting energy, the process technology which can highly harmonize conflicting characteristics and various functions was developed for new ceramic materials. This paper summarizes the result in fiscal 1997. On design technology of the characteristics harmonizing process, the design and synthesis of ceramic precursors were made by using chemical reaction of metal organics. On analysis of fracture behavior by controlling microscopic and macroscopic particle shapes, orientations were observed by convergent ion beam. On control technology of a structure formation process, study was made on continuous pore shape control to form porous material with uni-directionally arranged pores in ceramic matrix, interface control between particles to decrease a plastic deformation temperature and improve a heat insulation, interface control between phases of a rare-earth silicate/silicon-carbide-based composite, boundary control between layers of piezoelectric ceramics, and boundary control of the composite where inorganic-organic hybrids occupy the interface between ceramic particles. 79 refs., 193 figs., 15 tabs.

  2. FY 2000 report on the results of the development of the environmentally friendly type high efficiency energy utilization system. Part 2. Study of the effective utilization technology of high efficiency energy (Study of the optimum system design technology); 2000 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    The paper conducted the development of the environmentally friendly type high efficiency energy utilization system and the R and D of the high efficiency energy effective utilization technology, and the FY 2000 results were summed up. As to the energy transportation/storage technology, the R and D were made on the following: methanol/energy system, non-equilibrium high efficiency methanol decomposition reaction technology, development of multiple functions of catalyst, high efficiency heat pump technology using hydrogen storage alloys, heat-hydrogen recovery/transportation/utilization technology, vacuum insulated heat transport piping system, surfactant used for high density heat transport, high density latent heat transportation technology, etc. Concerning the energy supply/utilization technology, the R and D were made of the heat supply system using high efficient heat pump corresponding to multiple fuels. Relating to the environmental load reduction technology, the energy conserved heat pump system using natural coolant. As to the optimum system design technology, the comprehensive preparation of element technology, etc. (NEDO)

  3. FY 1986 Report on research and development of super heat pump energy accumulation system. Part 2. Development of elementary techniques; 1986 nendo super heat pump energy shuseki system no kenkyu kaihatsu seika hokokusho. 2. Yoso gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-04-01

    Summarized in detail herein are R and D results of the chemical heat storage techniques and plant simulation, for R and D of the super heat pump energy accumulation system. For R and D of the chemical heat storage techniques, the R and D efforts are directed to the researches on the fundamental reactions and continuous exothermic reactions involved for the high temperature heat storage type (utilizing the metathesis reactions); researches on the physical properties, heat storage systems, solid-phase reactions, liquid-phase reactors, corrosion of the materials, and so on for the high temperature heat storage type (utilizing ammonia complex); collection of the data related to media and structural materials, tests of the elementary equipment for the absorption and hydration reactions, and so on for the high temperature heat storage type (chemical heat storage utilizing hydration); researches on the media properties and system performance, tests of equipment, and so on for the high temperature heat storage type (heat storage/heating utilizing solvation); researches on the heat storage media, heat storage techniques, corrosion of the materials, systems, and so on for the low temperature heat storage type (utilizing the hydration reactions by mixing solutes); and researches on the media, corrosion and elementary equipment, optimization of the system, and so on for the low temperature heat storage type (clathrate low temperature heat storage systems). (NEDO)

  4. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

  5. Research and development of system to utilize photovoltaic energy. Survey on system and peripheral technologies for utilization of photovoltaic power; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on systems and peripheral technologies for use of PV power in fiscal 1994. On the case study of PV communities, as housing zone PV community, Seibu Kitanodai housing estate mainly composed of detached houses, and the Suwa area of Tama New Town of apartment houses were selected to study PV power generation on a roof, wall and window. The result clarified that generated energy of a detached house reaches 3-4 times as much as consumed one, that of an apartment house is nearly equal to consumed one, and power generation of nearly 380MW is possible based on expected housing supply until 2000. As urban core zone PV community, the survey result on Ebisu Garden Place clarified that the expected PV power supply rate is 10% or more, 20% and 30% or more for hotel and office buildings, high-rise apartment building more than 30 stories, and medium-rise one of 10 and several stories, respectively. In Sakura industrial estate, the maximum generated power was nearly equal to consumed power in a weekday, and as inverse power flow in a holiday was considered, the annual PV power supply rate was extremely high.

  6. Development of large scale and wind energy conservation system. Operational studies on a large-scale wind energy conservation system; Ogata furyoku hatsuden system no kaihatsu. Ogata furyoku hatsuden system no unten kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for operational studies on a large-scale wind energy conversion system. A total of 8 domestic and foreign cases are studied for wind energy conversion cost, to clarify the causes for higher cost of the Japanese system. The wind power systems studied include Japanese (5 units at Tappi Wind Park, the same type supplied by company M), US (California Wind Farm, 300 units) and UK (Wales Wind Farm, 103 units) systems. The investment costs are 639, 285 and 189 thousand yen/kW for the Japanese, US and UK systems, respectively. It is also revealed that the power plant itself and assembling costs account for a majority (70 to 88%) of the total investment cost. The higher cost of the Japanese system results from a smaller number of units installed, and the power plant cost can be drastically reduced by mass production. Increasing size also reduces cost greatly.

  7. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Development of silicon substrate manufacturing technology for high-quality solar cell); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Kohinshitsu taiyodenchiyou silicon kiban seizo gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted for enhancing productivity and energy conservation by rendering continuous and automatic the electromagnetic casting process for manufacturing polycrystalline silicon substrates for solar cells. In the manufacture of ingots for substrates by continuous electromagnetic casting, the chuck type system for feeding power to the melt plasma was replaced by a roller type system, and the power feeding position was moved to the high temperature region. Also, an on-line ingot slicing technique was established. In the manufacture of substrates at a slicing rate of 300 {mu}m/minute, productivity of 115,000 wafers/month, yield of 98%, and thickness tolerance of 30 {mu}m were achieved. A high-speed cleaning technique was developed using a jet stream, by which the cleaning time was reduced to 5 minutes and the slurry recovery rate was elevated to 95%. Based on these, substrate-related costs in the case of 100 MW/year production was calculated, which resulted in a cost of 98.8 yen/wafer (target: 103.3 yen/wafer) for manufacturing 15 cm square substrates from ingots and in a 15 cm square substrate slicing and cleaning cost of 135.1 yen/wafer (target: 135.4 yen/wafer). (NEDO)

  8. Research and development of utilization technology of solar thermal system for industrial and other use. Research and development of key technology (energy conversion on technology using chemical reactions); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Yoso gijutsu no kenkyu (kagaku energy henkan gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for energy conversion technology using chemical reactions by the aid of solar energy. The demonstration runs were conducted by a bench-scale unit, which was operated stably for 100h, to produce promising results. The catalyst exhibits stable performance, without showing a sign of deactivation. It is found that the heat pump system works well, without being interfered with accumulated by-products. A heat of approximately 2,100kcal/h is recovered. It is confirmed that steam of 150{degree}C and 200{degree}C is generated from hot water of 80{degree}C and 95{degree}C, respectively. The bench-scale runs show a thermal efficiency of around 10%, which is lower than the target level. However, the runs with hydrogen-occluding alloy attain a process thermal efficiency of 30%. The system in which solar collector and chemical heat pump units are combined is evaluated with respect to its economic efficiency and operability for its eventual commercialization. 6 figs., 2 tabs.

  9. Fiscal 1998 R and D report on the human coordination/coexistence robot system (development of practical technology for rational energy use); 1998 nendo ningen kyocho kyozongata robot system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report reports the R and D on the human coordination/coexistence robot system possible to perform various works instead of people. As for an intelligent robot hand, 4-finger hand and arm hardware were developed and fabricated, and operation of the assembled system of them was tested. As for a robot platform, a remote control platform, and the interface specifications of command communication and data communication were studied. As for 3-D walk adaptive to land shapes, an analysis environment for a control algorithm and an easy-to-use environment for a virtual platform simulator were prepared. By using this analysis environment, the central part of the walk control algorithm, and a module for forming walk patterns were developed. In the application research on energy saving, various problems on dangerous and harsh conditions in construction and disaster restoration works were analyzed, and the needs of a humanoid robot for such works were studied. (NEDO)

  10. Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

  11. Report on achievements in fiscal 1999. Research and development of synergy ceramics (research and development of ultra-high temperature gas turbine for power generation); 1999 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho. Hatsuden'yo chokoon gas turbine no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research and development has been performed on the following themes: (1) high-temperature energy materials, (2) high-function active materials, (3) fundamental member material design technologies, (4) materials to activate specific environmental gases, (5) energy materials having high resistance to silicon groups, (6) porous multi-layer ceramic materials, (7) micro and macro applied analytic technologies, and (8) microscopically destructive analysis technologies. In Item 1, investigations were performed on the relationship of micro columnar particle structure of porous silicon nitride bodies with strength and destruction energy to identify the mechanism for manifestation of these characteristics. In Item 2, catalyst and electrode materials having the selectively separating and cleaning functions were developed, and materials to convert oxides thermo-electrically having high characteristics were discussed. In Item 3, polycrystalline alumina, polycrystalline zirconia, and zirconia particle dispersed alumina were fabricated on the trial basis to give them microscopic and macroscopic evaluations. In Item 4, crystalline hexa-aluminates in single phase were synthesized successfully. In Item 5, a synthesizing experiment was carried out on Ca-{alpha} sialon powder to evaluate and analyze the configuration phase of the product and the particle patterns. In Item 7, the homogenizing method was used to develop a three-dimensional program to analyze the correlation between the microscopic non-homogeneous structure and the macroscopic properties of synergy ceramics. In Item 8, the basic dimensions of porous alumina bodies were discussed based on energy density. (NEDO)

  12. Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology; 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (femto byo technology no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Ultrahigh-speed electronic technology is indispensable for creating industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. To establish the development policy of generation and transmission devices for femtosecond light pulses, research and analysis were made on nonlinear optical response and light pulse transmission properties. Basic issues on devices and materials such as mode-locked semiconductor laser, pulse compression device and light-light modulation material for coding were extracted. For new femtosecond light pulse control/distribution devices, research and analysis were made on response properties of intersubband transition phenomena in a semiconductor and electron spin relaxation phenomena, and semiconductor quantum structure. To develop metrological technology using ultra-short light pulse, study was made on an evaluation method for time- fluctuation of pulses in 100 femtosecond level. Generation of femtosecond high-intensity X-ray pulse was possible by fine control of the existing high-intensity laser. 19 refs., 26 figs., 1 tab.

  13. Report on the joint research on the technology development of energy use reduction gas diffusion electrode salt electrolysis; Kyodo kenkyu energy shiyo gorika gas kakusan denkyoku shokuen denkai gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of energy conservation in the 'soda industry' which is an energy multi-consumption industry, study was made of the commercialization applying 'gas diffusion electrode' which is used for fuel cells, and the FY 2000 results were summed up. As to the development of production technology of gas diffusion electrode, conditional studies were conducted of the material production process, grinding process, mixing machine, filling, coating process, hot press process, etc. Concerning the evaluation of durability of the gas diffusion electrode, analysis of long-term operation electrode was conducted, and a lot of information on the degradation mechanism was obtained. In the degraded electrode, wetting of gas diffusion layer is going on, which is thought to directly cause the degradation. It is supposed that between the stable electrode and the degraded electrode, there are no changes in diameter of carbon powder and there is no carbon consumption. As to the verification test using the practical scale electrolytic cell, a trial operation started in February 2001. About the electrolytic performance, the electrolytic voltage is appropriately 2.2V, keeping the stable numerical value. The comparatively favorable performance is being maintained. (NEDO)

  14. Fiscal 1997 survey report. Survey consigned to NEDO of the development of energy use rationalization home welfare equipment systems; 1997 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa. Itaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of constructing new home welfare equipment systems of an energy effective use type, an investigational analysis was conducted of characteristics of the structure of houses considered of aged people, characteristics of the use of home welfare equipment, etc. As to the subject on space warming/cooling, it was found that the hour of stay-at-home of the aged tends to be longer, and the hour to be required for warming/cooling is longer, that the aged gradually lose senses regarding the peripheral environmental temperature, and the temperature to be considered should be at warmer/cooler levels, and that they are weak in heat shock, and the space of house where the temperature is uneven should be removed. Further, from the study in each welfare techno-house, possibilities were pointed out of further energy conservation in houses considered of the aged and home welfare equipment systems like the weight reduction of home welfare equipment systems and reduction of stand-by power, high air-tightness/high thermal insulation of houses for the aged, use of waste heat from air conditioners, introduction of solar energy to stand-by power and electrically-driven wheel chairs. 257 figs., 89 tabs.

  15. Achievement report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. 2. Research of technology of effectively utilizing high-efficiency energy / research of optimum system designing technology; 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu, saiteki system sekkei gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This 2nd volume deals with the transportation and storage of energy in the above-named research. In search of technologies for transporting exhausted heat from the industrial area to the urban section for consumers to utilize the heat for driving their air-conditioners and hot water supply systems, the decomposition and composition reactions of methanol are utilized for a long-range transportation system. The subjects taken up in this connection include the research and development of a methanol energy system, non-equilibrium high-efficiency methanol decomposition technology, multifunctional catalysts, and highly active/selective catalysts capable of promoting reversible endoergic/exoergic reactions. Research and development is also conducted of a high-efficiency heat pump technology using hydrogen-absorbing alloys, and such a pump will realize an air-conditioning system not dependent on chlorofluorocarbon. In the research and development of a long-range heat transportation system using hydrogen-absorbing alloys, a study is made of technologies of heat/hydrogen recovery, transportation, and utilization. (NEDO)

  16. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Sapporo City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Sapporo) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Daily, weekly and annual changes in energy use at care-taking sites were studied with the following six assignments enumerated: (1) studies on energy use amount in residential houses in the Hokkaido district, (2) discussions on improving energy conservation and efficiency in electric room heating systems and road heating, (3) evaluation on indoor air environment and discussions on effectiveness of air cleaning devices and ventilation systems, (4) surveys and studies on rational snow disposal methods for houses for physically handicapped and elderly persons and on housing patterns, and (6) surveys on effects of room warming environment in energy saving type houses on body feeling of elderly persons. Development of at-home welfare device systems utilizing energy more effectively was studied with the following five assignments enumerated: (1) surveys on energy consumption evaluation of at-home welfare devices, (2) surveys on developing a method to simulate energy consumption by analyzing utilization of the at-home welfare devices, (3) surveys on energy consumption and pleasantness associated with movement from a living section using the welfare devices to outdoor, (4) surveys on a garage utilizing a home elevator and around the garage, and (5) surveys on temperature setting and energy consumption when humidity in the garage is adjusted. (NEDO)

  17. Fiscal 1996 report on the results of the study under a consignment from NEDO of environmental friendly type metal base-materials recycling utilization basic technology and element/overall process. For public; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko kyodo kenkyu itaku. Kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu: yoso sogo process kenkyu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A study of `the next generation new iron steel making process` was conducted in which impurity elements in scrap are removed and recycled into high quality steel making materials, and at the same time total emissions are reduced during the process from scrap melting to steel making. The paper reported the fiscal 1996 results. In the study of the scrap recycling process, conducted were a study of the total system to remove impurities in the high temperature preheating furnace, a large scale experiment of de-coaling combined type de-coppering/de-tinning under reduced pressure of iron melting, a study of recycling technology of dust to the scrap melting furnace, etc. In the study on preheating/melting technology, a study of the scrap melting furnace of high-productivity/low-energy vertical type, a study of the scrap preheating method using the packed bed type preheating furnace, a study on the flue gas control at the time of preheating/melting, a study of the fast assessment method for organic compounds in flue gas, etc. In the evaluation of the total system, a study of preheating/melting/environmental systems using experimental plants. 20 refs., 23 figs., 10 tabs.

  18. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D high performance flat panel display technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / koseino flat panel display gijutsu no sogo kaihatsu kenkyu (daiichi nendo ) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    One of the subjects in technology supporting the highly information-oriented society which will develop and diversify toward the 21st century is the construction of high grade man/machine interface. For it, high precision/high luminance/energy saving/thin plane displays are strongly requested. This R and D is to indicate models of systematical development in the region of element technology individually existing in the Shikoku area by forming a regional consortium in the industry/universities/government. Creation of new industries by gathering display related enterprises is a first step in a plan to realize `Display Island Shikoku.` As a concrete target, with the use of high-tech diamond semiconducting technology, a development is conducted of the high performance flat panel display using the negative electron affinity (NEA) electron emitter which drastically solves the problems such as luminance, visibility angle and response speed, the subjects on the commercialized liquid crystal flat panel display. 16 refs., 45 figs., 8 tabs.

  19. FY 1986 report on research and development of super heat pump energy accumulation system. R and D of total systems (Surveys on heat sources and heat-utilization systems); 1986 nendo super heat pump energy shuseki system kenkyu kaihatsu seika hokokusho. Total system no kenkyu (netsugen netsu riyokei no chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    The heat source systems and heat utilization systems are surveyed and studied for the super heat pump energy accumulation systems, in order to clarify effective application and application types of these systems in the domestic and industrial energy areas. These works include surveys on literature, both domestic and foreign, surveys on actual situations of the related facilities and plants and on-the-spot hearing, and numerical simulation to establish the basic data for some items. The FY 1986 program includes the literature surveys on heat source and heat utilization systems and on-the-spot hearing for the domestic energy areas, reviews of heat demand variation patterns, and studies on methodology for applying the data to the areas not investigated so far. For the industrial areas to which super heat pumps are potentially applicable, the chemical, refining, food manufacturing and plastic manufacturing/processing industries are selected, to study problems related to system structures and conditions of the heat pump systems in these areas. (NEDO)

  20. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 8) - development of hydrogen production technology; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 8. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    R and D was conducted with the view of establishing hydrogen production technology based on the solid high polymer electrolyte water electrolysis method, which presumably offers higher efficiency and lower cost than conventional methods. This year, as well as implementing development of large-scale cell lamination (electrode area 2,500 cm{sup 2}, 10 cells) by using two hydrogen production methods (electroless plating method and hot press method), work was started for developing cells (electrode area 1,000 cm{sup 2}) for hydrogen stations. In the research on longterm durability improvement, with a 50 cm{sup 2} membrane electrolyte or cell, the evaluation test results were obtained of stable electrolytic performance showing more than 93% energy efficiency after 400 hour operation, under the conditions with electrolysis pressure 0.4MPa and electrolysis temperature 120 degree C. In a test of 1,000 cm{sup 2} prototype cell for hydrogen stations, the evaluation result was obtained for energy efficiency of 92% under the conditions with electrolysis pressure 0.5MPa and electrolysis temperature 120 degree C; thus, this year's target efficiency of over 90% was achieved. Further, enhancement of the quality was contrived for example by improving the electroless plating method and remodeling a roll press machine. (NEDO)

  1. Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

  2. Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

  3. Fiscal 1997 report on the results of the introductory R and D of the New Sunshine Project under a consignment from NEDO. Introductory R and D of the supercritical fluid use technology; 1997 nendo `New Sunshine keikaku` sendo kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The R and D of chemical reaction using supercritical fluids started in fiscal 1997. In the R and D of solvent reaction, as the research on polymer decomposition with supercritical water, studies were conducted of the mechanism of conversion reaction to chemical materials, cleavage mechanism of stable chemical bonds, and synthetic reaction in the supercritical state reaction field. In the research on oxidation reaction, as the study of complete oxidation in supercritical water for high efficiency energy recovery, studies of complete oxidation of liquid fuels, and complete oxidation of solid fuels. In the research on hydrogenation, studies of lightening of heavy oil in supercritical water, etc. In the R and D of the basic technology, studies of corrosion mechanism of metals in supercritical water, construction of the basic framework for technical database of supercritical fluids, etc. In the survey of technical trends and new research themes, the introductory R and D of element technology, etc. were conducted, and the results were described of the survey of technical trends and new research themes and the trend survey of overseas technology. 314 refs., 87 figs., 81 tabs.

  4. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 1. Survey/study concerning system evaluation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of formulating a strategy for introducing hydrogen, assessment was carried out on the energy consumption, environmental impacts and cost effiectiveness concerning various hydrogen utilization systems. In regard to soda-electrolysis by-product hydrogen and coke-oven by-product hydrogen, hydrogen supply capacity and cost effectiveness were evaluated. As a result, the two systems were found to have an annual hydrogen supply capacity of 11.52 GNm{sup 3} in total. As to the cost effectiveness, transportation by pipeline was 34 yen/Nm{sup 3}-H{sub 2} in the case of soda-electrolysis by-product hydrogen, and 40 yen/Nm{sup 3}-H{sub 2} in the case of coke-oven by-product hydrogen. An estimated cost of power generation showed 56 yen to 67 yen/kWh in such a system on remote islands as replacing diesel power generation by wind power generation, storing part of the electric energy produced in the form of hydrogen through water electrolysis, and using it as fuel for power generation by the fuel cell unit if wind conditions are unfavorable. Power generation cost on remote islands at present is sometimes in excess of 50 yen/kWh; therefore, this combined system showed promising results. The cost of using wooden biomass was estimated to be 51,000 yen/TOE , whose competitiveness is uncertain. (NEDO)

  5. FY 2000 report on the results of the R and D of the immediately effective/innovative energy technology. Development of the regenerative technology of energy saving type metal dust; 2000 nendo sokkoteki kakushinteki energy gijutsu kenkyu kaihatsu seika hokokusho. Sho energy gata kinzoku dust kaisei gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of the technology to recover iron and zinc components directly from high temperature exhaust gas emitted from the steel-making use electric furnace, etc. This process is more simplified than the conventional dust treatment process and markedly reduces the energy needed for zinc recovery. In FY 2000, the following were carried out: 1) development of the element technology to recover metal components in high temperature exhaust gas; 2) development of the technology to optimize the recovery process for metal components in high temperature exhaust gas. In 1), the following were proceeded with: grasp of conditions for metal recovery; development of the equipment to select/separate low vapor-pressure metal components; development of the heavy metal separation equipment to select/condensate zinc. As to the development of the equipment to select/separate low vapor-pressure metal components, it was confirmed by the element test that it was possible to separate iron by carbon material filter. Further, the reaction amount of gasification of carbon material was estimated to be small by the element test and simulational calculation. In 2), the bench-scale test device and small pilot test device were designed/fabricated. (NEDO)

  6. Technological development of machine tools using less energy in fiscal 2000. Achievement report on research and development of cutting process replacing electric discharge processing; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Hoden kako wo chikansuru sessaku kakoho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been made with an objective to replace the electric discharge processing consuming a large amount of energy and having environmental load, with the cutting process consuming less energy while maintaining the equivalent processing precision. This paper summarizes the achievements in fiscal 2000. Development of cutting tools has made three times or more as many multi-aspect utilization as compared to conventional tools possible by researching the tip shapes. In addition, ultra hard end mill suitable for cutting very hard materials using an ultrasonic cutting head was fabricated on the trial basis, and its cutting capability was verified. In developing the cutting processing heard, a vibration mode possible of cutting with the ultra hard tool was generated, ATC has become possible, and the possibility of cutting hard-to-cut materials was verified. For processing a narrow and deep part, an improved type tool was developed, whereas the practical cutting performance suppressing wear of the blade tip was obtained. To deal with the environment, development and prototype fabrication were performed on a unit having a grease lubricated high-speed main shaft that is considered to be the mainstream in the future. In the operation test at 20,000 min-L, know-how was acquired in relation with the basic performance, manufacture and use of the unit. (NEDO)

  7. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 3); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 3. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the (techniques for transportation and storage of energy (continued), energy supply and utilization, reducing environmental loads, and designing the optimum systems). The R and D on heat transfer system through the vacuum heat insulation pipes involves fabrication, on a trial basis, the vacuum insulation covers for the vacuum insulation tubes, joints, flanges and valves for the 80A pipes, and the heat loss evaluation test for each item. The R and D on the energy supply and utilization techniques involves the heat transfer systems for a variety of fuels by the highly functional heat pump, and compression/absorption hybrid type heat-utilization system. The hybrid type heat-utilization system simulation results suggest possibility of achieving exergy efficiency of 56% as the development target by use of the new medium. The R and D on the environmental load reduction involves the power-saving type heat pump systems which use a natural coolant. (NEDO)

  8. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) -research/study concerning international cooperation (Volume 1. research/study for promoting international cooperation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru chosa kenkyu (1. kokusai kyoryoku suishin no tame no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Various measures were implemented with the aim of realizing the 'longterm vision for international cooperation' in connection with hydrogen utilization international clean energy system technology (WE-NET) formulated in fiscal 1996. The English version of the 1998 annual summary report on results was distributed to approximately 170 pertinent organizations overseas. To develop understanding of the WE-NET project, presentations were given in numerous international conferences. In addition, as research cooperation in IEA (International Energy Agency), specialists were dispatched to the hydrogen implementation committee, the corresponding committee to hydrogen implementation agreement, and to each annex. In international exchange of technical information, each WE-NET task exchanged information with organizations abroad through overseas survey and conducted research on European hydrogen project, for example. With the purpose of developing understanding of WE-NET project activities, a preparatory work was done for participation in HYFORUM2000 (Germany) and World Hydrogen Energy Conference (Beijing) which will be held in 2000. (NEDO)

  9. Research report of FY 1996 on development of new hydrogen energy demonstration technology. 2. Results in the extension period of FY 1996; 1996 nendo kenkyu hokokusho. Shinsuiso energy jissho gijutsu kaihatsu (1996 nendo kikan enchobun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    The purpose of this project is to clarify the possibility of new hydrogen energy as a future energy source. The new hydrogen energy is obtained from the excess heat generation phenomenon through the electrolysis of heavy water using palladium metal as an electrode. The excess heat measurements were conducted through the excess heat confirmation tests using a fuel cell-type electrolytic cell up to November 1997. As a result, it was found that the excess heat measured by the calibration method can not be measured by the flow calorimetric method. In order to investigate the possibility of systematic errors of the both methods, the sensitivity, accuracy and responsibility, and the conditions of the excess heat generation, research activities based on new facts from scientific information and fundamental research supporting projects have been mainly performed. Among these, were performed the excess heat measurement tests by the cataphoresis method, absorption tests by the high-pressure and high-temperature charging method, gas plasma loading, in-situ X-ray detection, and reactant detection tests using Au/Pd/PdO heterogeneous structural body. 5 refs., 59 figs., 9 tabs.

  10. Achievement report for fiscal 1990. Research and development of ceramic gas turbine (Study on its adaptability with society); 1990 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Shakai tekigosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    With an objective to assist proliferation of ceramic gas turbine (CGT) which is desired of being put into practical use at an early time because of its effects of energy conservation, environmental preservation, and economic influence, investigations and studies were made on the CGT systems for cogeneration and portable power generation with regard to their latent markets, utilization patterns, and durability. In Section 1, investigations were given on stocking quantity by size in civil use buildings as the back-data for identification of effects by CGT and for estimation of its proliferation; identification of electric power to heat ratio (heat quantity/electric power amount) and patterns in use of energy in industries promising in CGT introduction; and on stocking quantity, energy demand and utilization patterns in industrial facilities. In Section 2, discussions were given on heat-power characteristics of the CGT, and energy utilization systems as the feasibility study on applicability of the cogeneration using the CGT. In Section 3, discussions were given on corrosion resistance of non-oxide based ceramics in relation with durability of the CGT, and oxidation behavior of silicon carbides in high temperature steam. In Section 4, future investigation assignments were discussed. (NEDO)

  11. Fiscal 1998 research report. Survey on R and D, and application technology of biotechnology; 1998 nendo chosa hokokusho. Bio technology no kenkyu kaihatsu, sangyoka gijutsu nado ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made mainly on use of biotechnology as resource saving and energy saving processes. Biotechnology is in wide use in a pharmaceutical field, while its application is on the increase in agriculture, food, chemistry, energy and environment fields. The USA is ahead of Japan and Europe. In the USA, there are more than 1000 ventures, and R and D of biotechnology, in particular, gene analysis and manipulation techniques are in progress together with acquisition of patents. In biomass energy, production of ethanol from corn, and development of biodiesel are in progress in the USA and Europe, respectively. Use of biomass should be promoted because of its global environment compatibility and sustainable productivity. In the future bio-market, genome analysis and its application are most important, however, Japan is behind in such technology in the world. The Joint approach by industry, university and government is necessary from the viewpoint of a future marketability and international competitiveness. Promotion of a public acceptance and nurture of creative talents are also important. (NEDO)

  12. FY 1993 Research and development of advanced ceramic gas turbines. Researches on social adaptability; 1993 nendo senshingata ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Shakai tekigosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    The ceramic gas turbines (CGT's) for, e.g., cogeneration and portable power generation systems are studied and evaluated for their environmental preservation, energy saving and economic characteristics. Types of utilization and market sizes are also studied for, e.g., portable power generation systems. The items studied include current status of cogeneration systems in USA, and recognition of cogeneration systems in Japan. The study results lead to the conclusions that the biaxial CGT for portable power generation systems is a promising substitute for diesel engines as the power source in the future, and 300kW class CGT's will have the markets of 170,000 units and potentially 450,000 units, because of their expected wide applicability. The studies on their economic, energy-saving and environmental load reduction effects indicate that one unit brings the economic effects totaling 616,000 yen, due to reduced fuel consumption and NOx abatement. They could reduce NOx emissions by 8,090 t/y for automobiles and 6,570 t/y for the others, when they fill the potential markets. (NEDO)

  13. Report on achievements in fiscal 1999 on research and development of the industrial and scientific technology. Research and development of synergy ceramics (development of a technology to rationalize use of energies); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper summarizes the achievements in fiscal 1999 on research and development of a technology to use synergy ceramics as a material, its application technology and the common base technology. In the research of high-function active materials, development was made on catalyst and electrode materials having the selection, separation and rinsing functions, and discussions were given on materials for thermoelectric conversion of oxides. In the research and development of new thermoelectric conversion ceramics materials, searches were made on cobalt and nickel containing compound oxides. In the development of corrosion-resistant electrochemical cell materials, the honeycomb type was devised, and a technology was developed to form honeycombs laminated with different materials. In developing self-lubricating functional materials, silicon nitride with solid lubricant of MoO{sub 3} dispersed on the surface layer was developed, wherein tribological characteristics were evaluated. In developing ultra-smooth low friction materials, studies were carried out on reducing friction by controlling silicon nitride and its surface structure, placing lifter shims in an automotive engine as the application object. The joint research with the National Research Institute performed evaluations on the compound function manifestation process. (NEDO)

  14. Research and development of system to utilize photovoltaic energy. Study on large-scale PV power supply system; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyo energy kyokyu system no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on large-scale PV power supply systems in fiscal 1994. (1) On optimization of large-scale systems, the conceptual design of the model system was carried out which supposes a large-scale integrated PV power generation system in desert area. As a result, a pair of 250kW generation system was designed as minimum one consisting power unit. Its frame and construction method were designed considering weather conditions in the inland of China. (2) On optimization of large-scale transmission systems, as large-scale power transmission systems for PV power generation, the following were studied: AC aerial transmission, DC aerial transmission, superconducting transmission, hydrogen gas pipeline, and LH2 tanker transport. (3) On the influence of large-scale systems, it was estimated that emission control is expected by substituting PV power generation for coal fired power generation, the negative influence on natural environment cannot be supposed, and the favorable economic effect is expected as influence on social environment. 4 tabs.

  15. FY 2000 report on the results of the development of the environmentally friendly type high efficiency energy utilization system. Part 1. Study of the effective utilization technology of high efficiency energy (Study of the optimum system design technology); 2000 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 1. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    The paper conducted the development of element technology and comprehensive adjustment which are related to the development of the environmentally friendly type high efficiency energy utilization system and the study of the high efficiency energy utilization technology, and the results of FY 2000, the final fiscal year, were summed up. As to the R and D of the exhaust heat reforming/recovery system, the internal heat exchange type distillation tower was developed which has a good energy conservation effect and enables the heat supply outside. Concerning the R and D of the cogeneration system using low calorie exhaust gas, the following were conducted for further improvement of the performance of electrothermic elements: evaluation of the thermoelectric performance using bulk elements, development of new elements and evaluation of the energy balance at the time of combustion, etc. Relating to the R and D of the low temperature exhaust heat utilization cogeneration system, conducted were the development of thermoelectric materials and the fabrication/evaluation study of module. Moreover, WATT20A equipped with the original power generation module developed in this study was fabricated, and the data on the operation at the temperature of 150 degrees C were obtained by WATT-20HT. (NEDO)

  16. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Third year report. R and D of a hybrid pulse plasma coating (HPPC) system; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Hybrid gata pulse plasma coating (HPPC) system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of the surface reforming technology system in which plasma CVD technology and PSII (plasma source ion implantation) technology are connected. HPPC forms DLC (diamond like carbon) layers excellent in adhesion and ceramic layers on the surface of work pieces such as complicatedly shaped dies and tools/sliding parts. Element technologies are the raw material gas pulse introducing technology for efficiently introducing raw materials into the reaction container in a state of gas, high density plasma formation technology and pulse plasma formation technology, minus pulse voltage application technology for vertically implanting various ions on the surface of complicatedly shaped work pieces, and advanced hybrid control technology enabling the control of ion species/implantation amount/layer formation speed. In FY 2000, using the prototype of the HPPC system, studies were made of the development of the DLC layer process and the low temperature DLC layer process, and development and commercialization of technology to improve throwing power, etc. (NEDO)

  17. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. R and D of new composite polymer electrolyte for battery; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Denchiyo shinki fukugo polymer kei denkaishitsu no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of new composite polymer electrolyte for Li secondary battery. The ultimate target of the development using this electrolyte is to get Li secondary battery markedly improved in safety/reliability which works at low temperature and controls thermal runaway. The composite polymer base electrolyte is composed of high molecular weight polyethylene oxide copolymer, ethylene oxide oligomer and Li salt, and it is finally cross-linked by heat or light. Studies were made in the following 6 fields: 1) R and D of the creation and optimization of new composite polymer electrolyte; 2) R and D of the commercialization of composite polymer electrolyte battery; 3) R and D on the safety of composite polymer electrolyte; 4) study of the synthesis of new electrolyte and catalytic activity of electrolyte-electrode interface; 5) R and D on polymer/oligomer composite electrolyte; and 6) comprehensive investigational research. (NEDO)

  18. FY 1977 Annual report on Sunshine Project results. Research and development of solar energy systems for air conditioning and hot water supply (Research and development of glass-based materials); 1977 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Glass kei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-05-01

    This project is aimed at development of the following collector techniques for various types of solar energy systems for air conditioning and hot water supply: (1) selective transmission glass, (2) reflection-preventive glass, (3) glass-based selective absorption film, and (4) high-performance collector. For the item (1), the STG coated with a reflection-preventive film of In{sub 2}O{sub 3} and that with MgF{sub 2} attain the target performance, and high-speed sputtering is investigated for development of the mass production techniques and promising results are produced. For the item (2), formation of a uniform reflection-preventive film on the glass's front surface and improvement of the reproducibility are investigated, and promising results are produced. For the item (3), a selective absorption plane having a solar radiation absorptivity of 0.90 or more and infrared emissivity of 0.30 or less is produced by baking a SnO{sub 2} film on a soft steel plate undercoated with a black glaze as the glass-based film. For the item (4), a total of 4 types of collectors are fabricated on a trial basis and tested for their heat-collecting performance; a honeycomb type with the selective absorption film, modified laminated type with changed pipe arrangement, one using a large-size reflection-preventive glass, and another one with changed method for supporting the heat-collecting plate. Attainable performance level of the flat plate type collector for commercial purposes is estimated, and the specifications of the commercial collector as the research target are determined. (NEDO)

  19. Fiscal 2000 survey report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Research and development of micrometer-order controlled material creation process technology); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu (micrometer order de seigyosareta material sosei process gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are exerted to develop sub-millimeter order coating creation technologies for engine cylinder bores, valve seats, and the like, for improvement on the performance of tribology related parts, which is necessary to assure environmental preservation, energy conservation, and resource conservation for industrial and transportation equipment. The coating liquid is applied in drops to the object and is irradiated with laser for re-melting for the formation of a coating. The technique is characterized in that it produces a 100 micrometer order coating. Activities are conducted in the four fields of (1) the technology of forming a coating by the use of high energy pulse laser, (2) technology of wear resistant surface treatment, (3) technologies for creating self-heating compounds and for bonding the same in practical applications, and (4) the analysis of the mechanism of tribological characteristics of a coating fabricated by hybrid laser surface treatment. In field (3), an Fe{sub 3}Al coating is fabricated by a combustion synthesis process in which a powder coating is pressed and simultaneously electrified for combustion (reaction), and the result is tested for physical properties. (NEDO)

  20. Present developmental conditions petroleum substituting energies in the EU; Sekiyu daitai energy kaihatsu no genjo (EU)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report outlines the policy of development and introduction of petroleum substituting energies, and its diffusion situation in the EU. On the policy, development, introduction and diffusion of petroleum substituting energies in the EU, based on the new EU energy white paper issued in fiscal 1996, the policy of energy and environment in every EU country is first outlined. The policy of and practical approach to petroleum substituting energies in every EU country are next described. In particular, since ALTENER which has been continuously promoted by the EU for 3 years as main control measures against CO2 is newly moving toward the second plan, the trend of ALTENER and the new SAVE2 plan are presented. The content of JOULE-THERMIE is also precisely presented which is the new energy program of the 4th framework R & D program. In relation to the developmental trend of alternative energies to oil in the EU until 2020, its prediction result is presented on the basis of the latest study promoted by EC committee in the ALTENER plan. 10 tabs.

  1. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Survey and study of analysis of commercialization of solar-grade silicon material manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Taiyodenchiyou silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The trend of technology development, problems harbored therein, trend of the market, and the like were investigated for supporting the development of technologies for the mass production and commercialization of solar-grade silicon materials. Concerning the future of production enhancement and cost reduction in the manufacture of polycrystalline silicon solar cells, studies were made from the technological viewpoint. The results are shown below. It is estimated that approximately 4,500 tons of material silicon will be necessary in 2005 and 6,500-10,700 tons in 2010. Since the melting purification method of NEDO (New Energy and Industrial Technology Development Organization) now under development step by step toward commercialization as well as the conventional source will provide the necessary amount of material silicon, it is inferred that the development of solar cells will go on without any restraint originating in the semiconductor industry. With the commercialization of the technologies so far developed and the development/commercialization of the fast-acting high-performance solar cell technology, probabilities are high that the polycrystalline silicon solar cell manufacturing cost in 2010 will be as low as to be on the 100 yen/W (93-118 yen/W) level which is the level now held up as the goal. (NEDO)

  2. Research and development of evaluation system for photovoltaic power generation system. Research and development of evaluation systems for photovoltaic cells and modules; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of the evaluation system for solar cells in fiscal 1994. (1) On development of the performance evaluation method for solar cells, data collection, analysis and measurement of atmospheric conditions necessary for outdoor measurement were carried out to improve the measurement accuracy of laminated solar cells. The validity of measurement methods was verified by comparing experimental results with outdoor measurement ones to improve the indoor measurement accuracy by multiple light source solar simulator. Generated energy in solar cell module level was also studied in field. (2) On development of the reliability evaluation method for solar cells, deterioration data were collected and analyzed by long-term exposure test. As a result, it was clarified that Pmax values are directly affected by seasonal change in air mass, and deterioration of solar cells is hardly found after exposure test for one year, showing a stable state. The characteristic recovery experiment of amorphous solar cell modules was carried out, and the accelerated deterioration test method of thin film cell modules was also studied. 2 figs.

  3. Exploration for petroleum and natural gas in Sonai Plain

    Energy Technology Data Exchange (ETDEWEB)

    Konishi, K

    1965-09-01

    Exploration in the Sonai Plain by Sekyu Shigen Kaihatsu Kabushiki Kaisha (Oil Resources Development Corporation) since 1955 is described. The development tasks are made difficult due to the presence of permeability traps. However, 41 out of 65 wells drilled up to late March of 1965 have been successful. Quantities of crude oil and natural gas produced in 1963 were, respectively, 5 and 6 times those of 1958. The Sonai Plain is a relatively new area, and there are still many unknown factors, yet the rate of development has increased greatly. More and deeper wells are expected to be drilled with even better results.

  4. Fiscal 1974 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on the system for large buildings); 1974 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu. Ogata kenchikubutsuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-28

    Large buildings such as government office building, private office building and gymnasium are consuming a huge amount of fossil fuel as energy for cooling/heating and hot water supply. The final target of this project is a use of solar heat as energy for such systems in place of fossil fuel. The fiscal 1974 target of this project is as follows. The main part of the computation program was developed for system analysis on the whole thermal system composed of building structure, thermal load, and cooling and heating equipment. The small experimental thermal equipment and artificial light source were prepared to clarify the mechanism of solar heat collectors experimentally. As the first step of innovative refrigerator development, the small trial experimental equipment was prepared to clarify heat transfer characteristics for coolant recycling, and to develop an ideal structure heat exchanger possible to reduce the temperature difference between heating medium and heated liquid. Prior to development of a heat storage equipment, basic study was made on heat storage materials, heat insulation methods and characteristics of heat storage tanks. (NEDO)

  5. Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

  6. Achievement report for fiscal 1997 on joint research to develop fuel cell technologies for urban energy centers. Research on evaluating life of phosphoric acid fuel cells; 1997 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu kyodo kenkyu seika hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    This paper discusses life evaluation on phosphoric acid fuel cells of urban energy center type for regional energy supply and on-site type to be installed in buildings. Operation characteristics tests and disassembly checks allow to identify factors for voltage decrease, and estimate the life therefrom particularly if the voltage decrease is caused from catalyst activity. The time before 10% decrease value is reached is now about 40,000 hours. The creep analysis method that has been developed recently can predict deformation in full-size reformers nearly exactly, and is effective in operating the reformer and evaluating the life at the design stage. Creep buckling is the critical value, which is caused by ecliptic deformation of internal tubes in the second catalyst layer. In a heat exchanger for fuel gas preheating, carbon in the reformed gas is carbonized and deposited due to catalytic action of nickel in the brazing material that bonds plates and fins in the heat exchanger. Iron also has a possibility of performing catalytic action. In the on-site type 1,000-kW class fuel cells, no structural problems have been presented even after the operation has been stopped. In order to extend time interval between phosphoric acid supply into the cells, it is necessary to reduce difference in the remaining phosphoric acid amounts in the stack lamination direction and in the cell flat surface. (NEDO)

  7. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Kobe); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Kobe) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the Kobe district, studies were performed with the importance placed on energy consumption at care-taking sites. Power consumption of devices used in residential houses of families having physically handicapped and elderly persons has been measured for two to three months, and in addition a questionnaire survey was carried out on operation frequency of welfare devices. Particularly from the power consumption and the use frequency of the devices to keep warm heat environment for physically handicapped and elderly persons, meaningful findings were obtained from the viewpoint of effective energy utilization, summarized as follows: (1) energy consumption of welfare devices used in care-taking sites in homes is small; (2) the power consumption varies greatly depending on methods to keep the warm heat environment; (3) in the case of discussing residential houses arranged with considerations for elderly people, the warm heat environment is important, and room cooling and warming devices including air conditioners should be included in the category of welfare devices, (4) a proposal was made on structuring a 'system to match elderly persons' physical conditions' intended to make a warm heat environment most suitable for physically handicapped and elderly persons, and (5) a proposal was made on discussing a 'system combining solar cells with large capacity batteries' of effective energy utilization type. (NEDO)

  8. Present situation of the development of petroleum substitution energy (Germany); Sekiyu daitai energy kaihatsu no genjo (Doitsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper investigates and reports the developmental trend of petroleum substitution energy in Germany. Policies for the technical development and actual introduction of petroleum substitution energy in Germany are concerned with three energies: coal, natural gas, and new energy, except nuclear energy the use of which is against public opinion. Coal is the only abundant domestic resource, but not internationally competitive because of its cost. Brown coal obtained from the open pit mining is an abundant and low-cost domestic resource, but has the environmental problem. The latest technology is actually being introduced in which the thermal power generation is integrated into gasification, and the gas/steam turbine power generation. Natural gas is advancing in the use as energy source for space heating substituting for brown coal. The technology development of new energy is promoted mainly on such wind power and solar energy as are called renewable energy. As to the development of technology using renewable energy for which the rapid increasing use is not expected in near future, the target is directed mostly to CO2 control and the third world where there are no public electric power nets. 30 refs., 10 figs., 8 tabs.

  9. FY 2000 report on the results of the R and D of 'frontier carbon technology.' Development of the technology to rationalize energy utilization; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the FY 2000 results. In Chapter 1, development of electrically high functional diamond process technology, electric characteristics which frontier carbon materials have were made clear by the following four subjects, and the development was executed of original production process technology for realizing energy saving by heightening efficiency of electric devices, displays, etc. 1) development of morphology control; 2) development of technology to control electron emission characteristics; 3) development of technology to control oriented growth; 4) development of technology to enlarge single crystals. In Chapter 2, the basement technology of electron emission control was studied. Namely, conditions for film formation were investigated to elucidate the formation mechanism of carbon nano structure films by Dual RF CVD method, IPC CVD method and thermal CVD method. As to the electron emission mechanism of diamond, electron emission characteristics were outlined of the boron dope diamond thin film formed by micro wave plasma CVD method in FY 1999. In Chapter 3, investigational study of original production process technology of electrically high function materials, test study was made of the element technology needed to make high quality/large area diamond substrates. (NEDO)

  10. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 2); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the (techniques for transportation and storage of energy). The R and D on methanol energy systems involves the R and D on decomposition and synthesis catalyst of methanol and methyl formate for the waste heat sources of relatively low temperature. The R and D on high-efficiency techniques using hydrogen-occluding alloys involves development of heat exchangers of low sensible heat ratio, fabrication of double-effect type MH heat pump cycle devices, and demonstration tests for the system operation. It is found that the heat output of the hydrogen-occluding alloy for high temperature use is 0.18kW/kg at 90 degrees C, and that the alloy can be massively produced. A thermal utilization efficiency COP of 0.68 is obtained for the double-effect type MH heat pump cycles. The R and D on the heat-hydrogen recovery, transportation and utilization techniques involves designs and fabrication on a trial basis of a sensible heat recovery unit. (NEDO)

  11. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use (Shizuoka City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Shizuoka) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to achieve rationalization in energy use, surveys and studies were performed on structuring new at-home welfare device systems of effective energy utilization type, based on structural characteristics of residential houses arranged with considerations for elderly people, and operation characteristics of at-home welfare device systems. For the 'evaluation of daily, weekly and annual changes in energy use at care-taking sites', measurements were performed on cumulative power during operation standby and momentary power under no load and load in eight care-taking devices such as a care-taking Gatch bed, a motor-driven lift-up cooking table and a home elevator installed in the WTH Shizuoka, by using a house energy measuring device. The measurements verified that large power is consumed during standby operation. In developing the 'at-home welfare device systems that utilize energy more effectively', a solar beam measuring device was used to measure over an extended period of time the power generation amount of a solar beam power generation system installed in the WTH Shizuoka. Evaluation was given on the system as an emergency power supply for an emergency event, and consideration was given on the effectiveness of the system in the Shizuoka district where daily sunlight irradiation lasts long. Development was made on an inexpensive walking training device, on which effectiveness as a waling training device was evaluated by using a position sensor and a force plate. (NEDO)

  12. Report in fiscal 1999 on the achievements in research and development of the ITS technology using clean energy driven automobiles. Research and development of an efficient utilization system for car rentals in tourist resort areas; 1998 nendo clean energy jidosha wo mochiita ITS gijutsu no kenkyu kaihatsu seika hokokusho. Kankochiyo rentaka koritsuteki riyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1998 on developing ITS technology using clean energy driven automobiles. Development is intended on an efficient management and control method for EV car rentals in tourist resort areas using the ITS technology from the viewpoints of reducing road traffic load and global environment problems. The development items include a control center system, a system to control battery charging status at the center, a battery charging determination algorithm, and a car navigation and bi-directional communications mounting system. The system development has been completed nearly completely, having attained relatively high user satisfaction. However, because of the experimental rented cars having long mileage, there were few chances of verifying the charge determination algorithm and the functions of the ITS. Investigations were carried out on technological trends in overseas countries on EV and ITS, and on commuter car introduction projects. Structuring the hardware for a commuter EV system is not too difficult if the presently available EV and ITS technologies are used. However, in advancing commercialization, there are such assignments as establishment of software, operation patterns, and interfaces that enhance user convenience and profitability. (NEDO)

  13. FY 1988 Report on research and development of super heat pump energy accumulation system. Part 1; 1988 nendo super heat pump energy shuseki system no kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-11-01

    Summarized in detail herein are the 1988 R and D results of the super high performance compression heat pumps and elementary equipment/media, for R and D of the super heat pump energy accumulation system. For R and D of the heat pumps, the R and D efforts are directed to manufacture, on a trial basis, and installation of the bench plant, and preparation of the basic plan for the pilot system for the highly efficient type (for heating only); to researches on the screw compressor, bench plant operation, heat exchanger, and so on for the highly efficient type (for cooling and heating); to development of the compressor with which a screw type expander is integrated at the low-temperature side, evaporator and so on, test runs of the bench plant, researches on the control methods, and so on for the high temperature type (utilization low temperature heat source); and to manufacture, on a trial basis, of the high-speed reciprocating compressor and steam supercharger, and tests for demonstrating their performance for the high temperature type (utilizing high temperature heat source). For R and D of the elementary equipment and working fluids, the R and D efforts are directed to the evaporator and EHD condenser for the mixed working fluids, heat exchanger, working fluids (alcohol-based and nonalcohol-based), and so on. (NEDO)

  14. Achievement report for fiscal 1991. Research and development of ceramic gas turbine (Study on its adaptability with society); 1991 nendo ceramic tas turbine no kenkyu kaihatsu seika hokokusho. Shakai tekigosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-05-01

    With an objective to assist proliferation of ceramic gas turbine (CGT) which is desired of being put into practical use at an early time because of its effects of energy conservation and environmental preservation, discussions were given on the cogeneration system (CGS) with regard to the system design, the effect calculation and its latent markets. In Section 1, discussions were given on the energy demand characteristics in business facilities such as hotels and hospitals, and on the CGS using the CGT. Section 2 calculates effects of introducing the CGT/CGS in business facilities, Section 3 discusses the latent market quantity of the CGT/CGS for business facilities, and its social adaptability including the environmental load, Section 4 studies the CGT characteristics and the status of its development, Section 5 researches heat resistant ceramics members, and Section 6 considers the future GCT utilization fields and problems in its effective utilization. In Section 2, it was estimated that the maximum energy saving effect can reach 21% when a facility that has been operated on purchased electric power and town gas introduced a CGT/CGS system consisted mainly of an absorption type freezer and a boiler. (NEDO)

  15. Present developmental conditions of petroleum substituting energies in France; Sekiyu daitai energy kaihatsu no genjo (France)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The French Government most enthusiastically promotes development of bio-gasoline in renewable energy field. EU makes pressure to remove the French Government`s fiscal advantages for bio-gasoline which only benefit French farmers, and the IEA (International Energy Agency) report also estimates no benefit corresponding to the fiscal support cost. Start of the `Eolien 2005` project is attractive in renewable energy field which aims at construction of wind power generation stations of 250-500MW by 2005. The `Eolien 2005` project is mainly supported by Electricite de France (EDF) who guarantees the purchase of produced electric power at a submitted price. In addition to this subsidy activity, EDF decided to positively tackle renewable energy. On R and D efforts for renewable energy, France belongs to the most poor countries among IEA countries, and in addition, the effort is considerably concentrated onto the study on reduction of production cost for bio-gasoline. There were no changes in this situation in 1996. 7 refs., 5 figs., 31 tabs.

  16. Research and development of basic technologies for next generation industries, 'high crystalline polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo (dainiki kenkyu kaihatsu kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This research and development is intended to establish a basic technology related to high crystalline polymeric material that has dynamic properties comparable to metallic materials by single polymeric material as a structural material. Thick and large high-elasticity molded forms were obtained by searching poly-arylate material, and by developing such processing technologies as high-pressure injection molding, composite injection molding, and elongation fluidity molding. High-elasticity molded forms with uniform internal orientation were obtained by heating and molding liquid crystal polymers under high magnetic field. Solution molding was performed on a molecular composite consisting of rigid chains and soft chains, which was laminated and bonded to have obtained an isotropic form with as high elasticity as 54 GPa. In addition, high pressure powder formation of cross-linked polymers of di-acetylene system provided an isotropic form with sound wave elasticity of 23 GPa.

  17. FY 2000 report on the results of the advanced R and D for the UTES (underground thermal energy storage) system; 2000 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this study, study was made of the commercialization of the UTES (underground thermal energy storage) system using the underground heat source heat pump system technology as the base, considering that this is a technology suitable for the urban area where the heat demand intensively increases and a lot of exhaust heat and usable heat exist. By the realization of the UTES system technology, it is expected that the system promotes Japan's utilization of the unused energy and contributes to the construction of the CO2 emission control type society for Japan's energy policy and global warming prevention and secondarily to leveling of power loads and elimination of the heat island phenomenon in large cities. As to the UTES system which is aimed at being used for space heating and cooling and hot water supply in buildings, the following two were studied: the indirect system, BTES (borehole thermal energy storage) system, in which heat is collected/radiated from the ground by the heat exchanger installed underground; the direct system, ATES (aquifer thermal energy storage) system, in which the groundwater stored in aquifer is directly pumped up and used. The study was made in the items written below: 1) establishment of an system image of the UTES system; 2) evaluation study of effects of the introduction, practical applicability, etc. 3) extraction of the subjects for development. As a result, system images of the indirect/direct systems were obtained. (NEDO)

  18. FY 2000 report on the results of the advanced R and D for the UTES (underground thermal energy storage) system; 2000 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this study, study was made of the commercialization of the UTES (underground thermal energy storage) system using the underground heat source heat pump system technology as the base, considering that this is a technology suitable for the urban area where the heat demand intensively increases and a lot of exhaust heat and usable heat exist. By the realization of the UTES system technology, it is expected that the system promotes Japan's utilization of the unused energy and contributes to the construction of the CO2 emission control type society for Japan's energy policy and global warming prevention and secondarily to leveling of power loads and elimination of the heat island phenomenon in large cities. As to the UTES system which is aimed at being used for space heating and cooling and hot water supply in buildings, the following two were studied: the indirect system, BTES (borehole thermal energy storage) system, in which heat is collected/radiated from the ground by the heat exchanger installed underground; the direct system, ATES (aquifer thermal energy storage) system, in which the groundwater stored in aquifer is directly pumped up and used. The study was made in the items written below: 1) establishment of an system image of the UTES system; 2) evaluation study of effects of the introduction, practical applicability, etc. 3) extraction of the subjects for development. As a result, system images of the indirect/direct systems were obtained. (NEDO)

  19. Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

  20. Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

  1. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. Development of the production technology of clean hydrogen, etc. by direct methane reforming method; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Methane chokusetsu kaishitsuho ni yoru clean suiso nado no seizo gijutsu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of the hydrogen production method using the zeolite-base methane dehydrogenation cyclization catalyst with the specific porous structure. In this production method, there is no emission of process CO2, and hydrogen can be produced by supply of energy of 1/10 of that in the conventional technology. In FY 2000, the following were conducted: 1) conceptual design of a demonstrative experiment plant; 2) development of catalyst processing technology; 3) development of element technology such as improvement of catalyst performance. In 1), design/specifications for demonstrative experiment use plant were fixed by design estimation and process analysis using the mid-term fluidized bed experiment device. It was decided that the mid-term fluidized bed experiment device will be constructed to evaluate the methane reforming performance of catalyst and that the reaction tower should be the stationary fluidized bed type. In 2), a catalyst activity experimental device 100 times as large as the laboratory was fabricated to evaluate the catalyst performance. By optimization of reaction conditions and preparation of the catalyst composition, the targeted catalyst system was obtained. (NEDO)

  2. Achievement report on research and development in the Sunshine Project in fiscal 1978. Surveys and studies on patents and information (Surveys on information about new energy technology development); 1978 nendo tokkyo joho chosa kenkyu seika hokokusho. Shin energy gijutsu kaihatsu joho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    This paper describes the surveys on information about new energy technology development in fiscal 1978 in the Sunshine Project. The present fiscal year performed the surveys on the United States and France as the main subjects. For the solar energy development in the United States, surveys were made on power generation using solar heat, solar cells, difference in ocean temperatures, satellites, biomass, and solar energy air conditioning systems. Geothermal energy development was also surveyed. For coal energy, surveys were done on coal liquefaction, gasification, high-temperature gas turbines and MHD power generation. The U.S. energy policy has various kinds of cards. For the solar energy development in France, heat conversion and photo-cell conversion systems were surveyed, while the authorities take development promotion measures on solar heat conversion system under the judgement that this is the only contributor to the new energy development. Surveys were performed on trends in biomass as the biological energy conversion means of the solar energy. Geothermal energy is being advanced of development following that for the solar energy. Surveys were made also on power generation systems using wind power, wave power and difference in ocean temperatures. This paper dwells also on waste heat utilization, cogeneration, and heat pumps as examples for energy conservation means. (NEDO)

  3. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Imaichi City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Imaichi) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Evaluations were given on energy demand in residential houses arranged with considerations for elderly people based on district features for at-home welfare devices, and on change in energy use at care-taking sites. Surveys and studies were performed on structural characteristics of residential houses arranged with considerations for elderly people, and on structuring of at-home welfare device systems. The study items are as follows: (1) identification of the using patterns of the at-home welfare devices, and measurement and evaluation on electric power consumption, (2) measurement and evaluation on household energy consumption, (3) estimation on energy demand in residential houses for elderly people, (4) surveys on hot heat sensitivity, and (5) estimation on allowance for steps in rooms. In Item 1, electric power consumption is measured during standard operation of at-home welfare devices by using power measuring devices in the Welfare Techno-House (WTH) Imaichi. In item 2, a questionnaire survey is performed on the ways of living in elderly people's households and general households. In Item 3, energy demand is estimated in houses for elderly people incorporated with welfare devices, based on the results of Items 1 and 2. In Item 4, measurement and evaluation are made by using experiments on physiological changes in bodies of elderly people in toilet space in the WTH, and on a room heating system giving comfortable feeling. In item 5, discussions are given on air tightness of doors in barrier free sections, and on allowable limit of steps inside rooms. (NEDO)

  4. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the environment friendly type production technology. High-functional chemical synthesis bioreactor (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of developing production technology of chemical substances which are resource conservative, energy saving and less in environmental loads, a R and D was conducted of a high-functional chemical synthesis bioreactor. The paper reported the results of fiscal 1996. As for proliferation control breeding technology, relating to the switch control technology of proliferation related genes by regulatory factors, the effectiveness on an incubator level was demonstrated, and at the same time improvement of reactor performance in using this technology was studied on paper. As to the manifestation control breeding technology, the actual design of the development of manifestation promotion technology by bent DNA, etc. was proceeded with, and at the same time the following were commenced: selection of bent DNA, confirmation of bent characteristics, and work of vector construction using candidate bent DNA. Further, the simple assessment system of manifestation vectors was constructed. In the development of bioreactor system technology, the actual design was started of the two-stage culture continuance system which separated proliferation and enzyme production. 48 refs., 41 figs., 6 tabs.

  5. Achievement report for fiscal 2000 on the phase II research and development for the hydrogen utilizing international clean energy system technology (WE-NET). Task 1. Investigations and researched on system assessment; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-1. Technologies drawing attentions relate to fuel cell driven automobiles and hybrid automobiles in the field of utilizing hydrogen derived from reproducible energies and fossil energies, and fuel cell co-generation and micro gas turbine co-generation in the field of electric power generation. Hydrogen reformed from gasoline on board the automobile as the fuel for fuel cell driven automobiles, hydrogen as a by-product of coke furnace off-gas (COG), and reproducible energy hydrogen have the same fuel consumption performance as in the hybrid automobiles. Particularly the COG is low in cost, and has large supply potential. Liquefied hydrogen is as promising as compressed hydrogen in view of the cost for automotive hydrogen supply stations. What has high economic performance as the self-sustaining systems for islands are photovoltaic and wind power generation, and the system using hydrogen as the secondary energy. Since much of the reproducible energies is used for electric power demand in Japan, the by-product hydrogen and the reformed hydrogen in an amount of 9.3 billion Nm{sup 3}/year would take care of majority of the demand in view of the short time period. For a longer time span, hydrogen originated from the reproduced energies in the Pan-Pacific Region should be introduced. (NEDO)

  6. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  7. Development of a wide-area energy utilization network system (research on a technology to design an energy system). FY 1998 report on achievements of research on systematizing ECO and ENERGY cities; Koiki energy riyo network system kaihatsu (energy system sekkei gijutsu no kenkyu). 1998 nendo eko ene toshi no system ka kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    As a research on systematizing ECO and ENERGY cities, surveys and analyses were performed on the actual state of introducing district heat supply systems utilizing difference waste heats including factory waste heat. Waste heat from electric power generation is utilized for district heat supply in Japan at 122 points or about 20% of the district heat supply points in operation as of March 1998. The number is in the increasing trend in recent years, and the future potential of its introduction can be said high as the history thereof is still short. Its introduction form is accounted mostly for by building cogeneration or plant cogeneration. Back-up facilities for the case when waste heat supply stops because of regular facility checks are provided by the heat supply business operators, which impede the economy of the system. In the U.S., the Public Utility Regulatory Policy act motivated installation of cogeneration and off-peak power generation systems for district heat supply. Technical maps (for waste heat sources and different waste heat utilization systems) were prepared based on the surveys to discuss the future measures. (NEDO)

  8. Study on the current status of biomass energy development; Bio mass energy no kaihatsu jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was conducted on the present status of biomass energy in Japan and abroad and the developmental trend of the latest biomass energy technology. Brazil and the U.S. are most advancing in the biomass energy utilization. Brazil uses sugar cane which is plenty in supply as a raw material, and the U.S. does corn which is the surplus crop. Both countries use the conventional ethanol fermentation technology and produce the petroleum substitution liquid fuel which is in greatest need. As to the technology to convert biomass resource into energy, attention has so far been paid to the development of the production process of the liquid fuel. The latest technology for ethanol fermentation using saccharin and starch as raw materials has already been established in Japan, and the energy-saving type alcohol recovery technology has also reached the stage of practical application. Moreover, as to the ethanol conversion technology with cellulose substrate, the development of the saccharification process will be needed in future. 15 figs., 10 tabs.

  9. FY 1991 Report on research and development of super heat pump energy accumulation system. Part 2. Construction and operation of the prototype system (researches on elementary techniques and construction and operation of the pilot system); Super heat pump energy shuseki system no kenkyu kaihatsu 1991 nendo seika hokokusho. 2. System shisaku unten kenkyu (yoso gijutsu no kenkyu / pilot system no shisaku unten kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-05-01

    Summarized herein are R and D results of the researches on the chemical heat storage systems, plant simulation techniques and combined systems, and international technical exchanges, for R and D of the super heat pump energy accumulation system. For the high temperature heat storage type (utilizing ammonia complexes), the initial research targets are almost attained, as a result of the designs of a chemical heat storage unit having heat storage capacity of 1,000 kWh. For the high temperature heat storage type (utilizing hydration reactions), a 25 Mcal-scale pilot partial test unit is operated, to study applicability of the practical materials and other operation-related themes. For the low temperature heat storage type (utilizing hydration reactions by solute mixing), a pilot system is operated, to attain heat recovery of 75% or more, heat storage density of 30 kcal/kg or more, and output temperature of 7 degrees C. For the low temperature heat storage type (utilizing clathrates), the evaluation tests by a pilot plant produce heat recovery of 93.2% and heat storage density of 32.0 kcal/kg. In addition, the R and D efforts are directed to, e.g., researches on plant simulation techniques and combined systems. (NEDO)

  10. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Ube City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Ube) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The present study utilizes a Welfare Techno-House to analyze structural characteristics of residential houses arranged with considerations for elderly people, and operation characteristics of at-home welfare devices. It is also intended to identify the status of energy consumption, and research and develop energy saving devices. The research and development items for the current fiscal year are as follows: (1) survey on power consumption in at-home welfare devices, and (2) development of at-home welfare device systems utilizing energy more effectively - sub-item a.: studies on leveling of energy use, b.: studies on identification of load applied to riders of power driven wheelchairs when they are operated, c.: studies on next generation housing for elderly and physically handicapped people, d.: surveys on discharged VOC concentration in houses built in warm districts. In item (1), power consumption of air conditioners for room heating in winter was measured to have derived time series data of daily change in the energy consumption. In the sub-item a, discussions were given on system efficiency evaluation on ice heat storing devices and floor cooling devices, and the indoor thermal environment characteristics. In the sub-item b, load applied to riders of power driven wheelchairs when they are operated was experimented for verification. In the sub-item c, surveys were performed on hot heat environment in a greenhouse attached to a residential houses arranged with considerations for elderly people. In the sub-item d, measurements were carried out on formaldehyde concentration and VOC in houses newly built in warm and cold districts to discuss preventive measures for indoor air pollution. (NEDO)

  11. FY 1977 Annual report on Sunshine Project results. Research and development of solar energy systems for air conditioning and hot water supply (Research and development of solar systems for condominiums); 1977 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Shugo jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-06-01

    This project is aimed at technological development of economical solar energy systems for air conditioning and hot water supply for condominiums. The major items for the FY 1977 programs include (1) designs and fabrication of equipment for a test building, (2) development of the equipment materials, and (3) system analysis. The jobs for item (1) include management of the designs and construction, placing an order for the building, and fabrication of an air conditioner expander and heat pump; those for item (2) include simplification of a condensing type and plate type heat collector structures, weather-resistance of the plate type heat collector structure, and materials for selective absorbing membranes and reflectors; and those for item (3) include estimation of heat loads in a model building, first to third floors as the test building, and fourth to 14th floors as the conventional box-shaped building. The heat collector installation area is investigated for a multistory building, for which solar radiation intensity at the heat-receiving plane and the like are taken into account. It is found that the solar system can be installed, when an area of 50m{sup 2} can be allocated to the system in each story. There is a limit to story number for the solar system to economically work for air conditioning and hot water supply. Sufficient insulation of the system and reduction in pipe length by zoning are the necessary measures against heat losses. (NEDO)

  12. Fiscal 1998 result report on research and development project of regional consortiums (the first year). Research and development of regional consortium energy / Report on development of high-grade and low-cost molds for rubber and plastics; 1998 nendo chiiki consortium energy kenkyu kaihatsu (dai 1 nendo). Gomu plastic yo kohin'i tei cost kanagata no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Discussions were given on quality improvement and cost reduction of heating and forming molds for household rubber, plastics and electronic device parts. This paper summarizes the achievements in fiscal 1998. Verification was made on chromium plated steel and stainless steel molds as to improvement in water repellency of the mold surface by injecting N and F ions, improvement in surface hardness by making the surface into CrN and CrF, and improvement in wear resistance. In order to inject the ions uniformly into the mold surface having irregularities, a high-frequency and high-energy power supply was developed. Development was made on a negative voltage induction pulse power supply taking synchronism with the above pulse power supply and a 50-kV field through device. The design and fabrication thereof have been completed and the trial operation has begun. In order to evaluate mold releasing performance and pollution effect on molds under the same conditions for all makes, a unified evaluation criterion was established. With regard to nitriding and chromation by means of nitrogen ion injection into chromium plated steels under the unified rubber composition, the mold releasing performance and pollution effect were evaluated in terms of economics. Residue of rubber material in a mold has decreased, and metal polluting effect has been improved. Quantitative evaluation was performed successfully by the CCD taken image processing of surface images. (NEDO)

  13. Present situation of the development of petroleum substitution energy (East Europe); Sekiyu daitai energy kaihatsu no genjo (Too)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In East European countries (Albania, Bulgaria, Czech, Slovakia, Hungary, Poland, Rumania and former Yugoslavia), energy prices were raised as part of the general price reform in the initial stage of the economic reform. Trade regulations on energy products were relaxed, and prices of tradable energy products were made free. Even in countries such as Rumania and Bulgaria where there still remain controls, the governments aim at perfect liberalization. Thus, this paper first considered the energy situation of East European countries where economy and society are now changing. Described were the overall economy situation and energy supply/demand in East European countries. Next, the paper detailed the energy situation in Hungary and Poland. In conclusion, the paper considered energy and international cooperation, and Pan-european Energy Charter which are important future issues in the energy sector of East European countries. 10 refs., 36 figs., 26 tabs.

  14. Present situation of the development of petroleum substitution energy (The UK); Sekiyu daitai energy kaihatsu no genjo (Eikoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the petroleum substitution energy in the U.K., the paper states measures taken for the development and introduction and the state of spread. Introduced were the U.K., energy policy described by energy field, petroleum and natural gas, coal, nuclear power, electric power, renewable energy (petroleum substitution energy), and the policy on energy conservation and the recent trend. Further, the paper took up the environmental policy relating to global warming which is an environmental problem in close connection with the energy industry and described the present status of exhaust gas such as acid rain gas and ozonospherial destruction gas, target for reduction of exhaust gas, and the present situation of exhaust gas at power plant. Explained were the positioning of and the measures for the petroleum substitution energy which was incorporated into a part of the energy policy in the U.K., especially the recent trend of obligation to use non-fossil fuel. First, the order of priority of the governmental policies was introduced, and then the NFFO order was described which was to give reliable fund base to the development toward the practical use of petroleum substitution energy. The paper also commented on recent topics on the state of the practical use of petroleum substitution energy. 2 figs., 7 tabs.

  15. FY 2000 report on the results of the regional consortium R and D project - Regional new technology creation R and D. First year report. R and D of medicine toxicity assessment use hepatocyte chip; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium kenkyu kaihatsu / chiiki shingijutsu soshutsu kenkyu kaihatsu. Dokubutsu dokusei hyokayo kansaibo chip no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Judging that in the beginning of the toxicity test, the necessary information/knowledge are acquired not by using animal itself but only by using liver system (hepatocyte), the development was proceeded with of the hepatocyte chip substituting for the animal experiment. Studies were made in the following five fields: 1) design of functional matrices; 2) development of the pharmacological assessment technology; 3) development of cell sensing technology/biosensor fabrication; 4) study of a possibility and the limit of cell patterning technology; 5) survey of the market scale. In 1), studies were made of the establishment of the 3D culture method for hepatocyte and the construction of hepatocyte models for medicine assessment using pieces of liver. In the latter, by including capsule using the sugar introduced with galactose residue which is special sugar of hepatocyte to alginic acid and chitosan which are natural polymer and also hepatocyte isolated into sponge, aggregate was formed, and its use as a medicine assessment use liver model was tried to be made. (NEDO)

  16. FY 1998 result report on development of superconductive power application technologies. Pt. 1. Research and development of superconductive wire materials / Research of a total system / Research and development of a freezing system / Demonstration tests; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Superconductive technologies are introduced into electric power devices for attempts of achieving higher stabilization, density and efficiency, as well as size and weight reduction and improvement in performance of the devices. The project has been worked on since fiscal 1998 as part of the New Sunshine Project. Fiscal 1998 being the eleventh year has taken the following subjects as the research promotion policies: establishment of plans targeted at accomplishment of the goals of the project; adequate and reliable implementation of verification of technological assignments; and steady and efficient demonstration tests. Subsequent to the previous year during which site demonstration tests were completed on a low-speed responsive model machine, the site demonstration test has begun on the ultra high-speed responsive model machine as the final stage of the project. The ultra high-speed responsive model machine was coupled with a freezing system and a load synchronizing machine, and different kinds of test were carried out where good results were obtained. Researches were conducted on characteristics improvement and device element technologies aimed at achieving the practical application level by utilizing the respective features of AC metal-based wires and oxide-based wires, where sound results were obtained. Also in an improved freezing system, valuable data were attained as part of establishing the basic technologies for a superconductive power generation system. (NEDO)

  17. FY 1986 Report on research and development of super heat pump energy accumulation system. System construction and operational study results (Systemization studies); 1986 nendo super heat pump energy shuseki system kenkyu kaihatsu seika hokokusho. System shisaku unten kenkyu (system ka kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    The studies on combinations of high-performance compression heat pump and chemical heat accumulation systems are conducted to construct the optimum systems for air conditioning/hot water supply for large-sized buildings and local districts, and also for industrial processes. For partial optimization of super heat pump (SPH) accumulation system, the SPH operational mode is changed to find the optimum conditions. As a result, it is found that system efficiency is the highest, and hence the power cost is the lowest, when the system is continuously operated night and day, followed by 2-night/1-day mode and night alone mode, in this order, for office building air conditioning, district air conditioning, and hot water supply. The effects of combination of SHP and chemical heat accumulation systems incorporated in an industrial process for heating are estimated. The results indicate that power load leveling effect is not 100% but 92%, even when the heat required for the daytime operation is totally supplied from the chemical accumulation system. The skeleton of the super heat pump accumulation system simulator is finalized, and the elementary system modules are developed, to allow simulation of general flows. (NEDO)

  18. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly efficient polymeric separation membrane material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo saishu kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    For the enhancement of separation process efficiency and energy efficiency in the chemical industry, etc., basic technologies are developed involving high-performance separation membrane materials which are excellent in durability and usable in the field where separation by membranes has been impractical. The liquid mixtures subjected to separation are a neutral organic compound/water system, an acidic organic compound/water system, and a polar organic compound/water system; the gas mixtures subjected to separation are an oxygen/nitrogen system and a carbon monoxide/nitrogen system. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. Among those that have to be mentioned is the development of a nonaqueous separation membrane, a supported liquid membrane with amino acid optically active high performance separation capability, a high-precision evaluation unit for gas separation membrane characteristics, a selective permeation membrane with high-level oxygen and carbon monoxide carriers and reactivation technology, a high-performance ethanol separation membrane, a water/polar organic compound separation membrane, and a water/acetic acid separation membrane and stability providing technology. In particular, the water selective permeation membrane for a mixture of water and alcohol has already arrived at the stage of bench plant demonstration. (NEDO)

  19. FY 1999 achievement report on the development of high performance boilers. R and D on high performance industrial furnaces, etc.; 1999 nendo koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project started in FY 1993 to survey the actual state of industrial use boilers. Based on the results of the survey, in fiscal 1995, 1996 and 1997, no improvement of the present technology which has limits, but the development was made of the oxygen combustion and element technology which are factors for heightening boiler performance with a new idea first in the world. In fiscal 1998, a target for the overall thermal efficiency of 105% was settled by testing a pilot plant where the element technology was integrated into the small once-through boiler, flue/smoke tube boiler, water tube boiler, etc. In fiscal 1999, the target of the overall thermal efficiency of boiler was reached by a pilot plant test to clarify combustion characteristics, heat transfer characteristics, environmental characteristics, etc. Further, effects of energy saving were increased by the adoption method of oxygen supply equipment. Concretely, an overall boiler efficiency of 105.73% exceeding the targeted value of 105% was achieved at a pilot plant of actual scale, by concentrating the results of each of the element technologies such as 'oxygen combustion,' 'condensation type flue gas heat exchanger,' 'high performance combustion control device,' and 'rapid rotating auxiliary machine.' (NEDO)

  20. Fiscal 1996 report on the R and D result of industrial science and technology. R and D synergy ceramics (R and D on synergy ceramics); 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (synergy ceramics no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper summarizes the general survey mainly conducted by FCRA (Fine Ceramics Research Association) in fiscal 1996, and the joint research results with some universities, from some R and D on synergy ceramics. Silicon nitride based ceramics expressed the same high thermal conductivity as metal by seed crystal addition, grain growth control and orientation control of sheet lamination. For its practical use, study was made on control factors of material, formation and sintering. Ca2Y2Si2O9 single crystal was prepared by float-zone method to determine its crystal structure. No volume change due to high-temperature phase transition as thermal expansion was found. In carbothermal reduction- nitridation of SiO2, addition of Si3N4 seed powder increased a reaction rate and formed uniform particles with an isotropic shape. An average particle size was dependent on the size and number of fine particles in seed powder. Addition of both Si3N4 and Fe compound could change a particle shape from a spherical grain to an elongated grain. A spherical Fe-Si metal grain was found on the tip of an elongated grain. 66 refs., 73 figs., 13 tabs.

  1. Fiscal 1999 achievement report. Research and development of synergy ceramics; 1999 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Studies are conducted on three subjects, which are the development of 1) high-temperature energy materials technology, 2) ultrasophisticated materials technology, and 3) high-performance active materials technology. Under subject 1), high-strength porous materials are to be developed, which are resistant to heat and corrosion, tolerant of damage and deformation, and light in weight. In addition, relative to fluid transmission, materials are to be developed, which are highly resistant to heat, corrosion, and thermal impact, and capable of separating and removing particulates of powder dust. Under subject 2), efforts are under way to develop two technologies, related to materials creation and their application. The former technology involves the development of a process of simultaneously equipping materials with high wear resistance, desired friction factors, and desired mechanical and thermal characteristics; a process of equipping them with a trace damage detecting function; and a process of simultaneously equipping them with functions of restoration from accidents and of self-lubrication. Relative to the latter technology, efforts are conducted, in coordination with the endeavors for the above-said materials creation technology, to develop materials and their application with attention paid to some specified functions. Under subject 3), self-complete type ceramic materials not requiring an external driving power source are to be developed, in which a selective cleaning function and environmental energy conversion function are amalgamated. (NEDO)

  2. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  3. FY 1977 Annual report on Sunshine Project results. Research and development of solar energy systems for air conditioning and hot water supply (Research and development of systems for new residential buildings); 1977 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Shinchiku kojin jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-31

    This project is aimed at development of devices for solar energy systems for air conditioning and hot water supply, in order to commercialize innovative systems for economic air conditioning and hot water supply for new residential buildings. The research items are (1) development of materials for the devices (e.g., heat collectors and absorption refrigerators), (2) operation of the systems in the test building, and measurement (methods for measurement and evaluation of the systems in the test building, instrumentation systems and operation thereof, and analysis of the measured data), and (3) system analysis (system simulation, comparison of the simulated results with the observed results, and system variations). The item (1) studies economic efficiency, durability and stability of the vacuum glass tube type collectors. The item (2) studies a dripping type generator, refrigerant recycling type generator and generator with a built-in auxiliary heat source for the absorption refrigerators. These types have their own advantages and disadvantages, and it is necessary to establish how these results are to be included in the products. The item (3) changes the collector arrangement, based on the observed data, and improves heat-collecting pump starting/stopping conditions, refrigerator operating conditions and insulation around the primary heat-storage tank. It is necessary to analyze the improved systems. (NEDO)

  4. Research and development of photovoltaic power system. Research on low temperature deposition of polycrystalline thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Teion seimaku gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sato, K [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on research on a technology of low temperature deposition of polycrystalline thin films for solar cells. This research used ITO coated glass substrates, on which CdS was accumulated to a thickness of about 100 nm by using the CBD process, and over this deposition a CuInSe2 film was formed at 300{degree}C by using the ion cluster beam (ICB) process. The manufactured solar cells with a glass/ITO/CdS/CuInSe2/Au structure had an efficiency of 2%. In manufacturing a CuGaSe2 thin film by using the ICB process, effects of acceleration voltage relative to cluster beams and ionization current were investigated. It was found that the film morphology, the result of analysis by using X-ray diffraction, and the electric conductivity are sensitive to the ionization current. From these findings, an optimum film forming condition was derived. A CuGaSe2 thin film was manufactured by using the ICB process over a Cds thin film deposited by using the CDB process. Both of the surface morphology and X-ray diffraction patterns of the film did not show a large change, indicating a possibility of manufacturing cells with a reverse structure. Effects of heat treatment on CuInSe2 monocrystals were evaluated by using ESR and FTIR. 6 figs., 1 tab.

  5. Research report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. Research of optimum system designing technology (Research of effect of eco-energy city system technology introduction to Osaka); Kankyo chowagata kokoritsu energy riyo system kaihatsu Saiteki system sekkei gijutsu no kenkyu 1998 nendo chosa hokokusho (Osakafu). Ekoene toshi system gijutsu donyu koka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Concerning the district in Osaka Prefecture selected for study in fiscal 1997, it is investigated whether energy efficiency is enhanced, and environmental impact reduced, by the introduction of element technologies, and the findings are compared with the results expected to be produced without their introduction. Problems about their introduction are also discussed. Taken up for study are the collection and utilization of heat from a water granulated slag manufacturing plant of an iron mill, exhaust heat reform and recovery system at a chemical plant, heat supply system driven by a high-performance heat pump capable of dealing with various kinds of fuels, compression/suction hybrid heat utilization system, and a cold heat supply system using microspheres. Annual energy consumption, CO2 and NOx emissions, and costs are calculated for each of them. Concerning these element technologies, various tasks are discussed, related to the technology of their systematization, economy, dissemination of district heat supply, and wide-area heat supply businesses utilizing exhaust heat. As the result, it is concluded that the primary energy consumption as a whole is reduced upon their introduction and that energy saving effect and environmental impact reducing effect are in presence. (NEDO)

  6. Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

  7. Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

  8. Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

  9. FY 1997 research and development of fusion domains. Part 2. Studies on bionic design; 1997 nendo seika hokokusho (yugo ryoiki kenkyu kaihatsu). 1. Bionic design no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Studies were conducted on actuator function in bio materials, cells, structures, and living organisms, and on structuring a biological molecule machine. In the study on soft biological structures, biological compatibility of artificial glass bodies using ultra-polymeric PVA was found very high, raising expectation on feasibility of their practical use. Three-dimensional structure of glass bodies was made clear for the first time in the world. As a result of separating and purifying cells from a liver for the first time in the world, it was indicated that excellent proliferation performance and differentiation into cells are shown. With regard to hydroxyapatite in hard biological structure such as bones and teeth, single crystals were synthesized, and growth rate on the surface C was measured successfully. For molecular motors, studies are being performed on functions of twin-head structure in biological protein enzyme. In molecule structuring, studies were conducted on preparation of a hydrogenase LB membrane as an electric-hydrogen energy conversion element, and structuring of protein molecular structure using gene recombination. 69 refs., 37 figs., 8 tabs.

  10. FY 1977 Annual report on Sunshine Project results. Research and development of solar energy systems for air conditioning and hot water supply (Research and development of solar systems for existing residential buildings); 1977 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Kison kojin jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-05-31

    As part of the research and development of the solar energy systems for air conditioning and hot water supply for existing residential buildings, the following efforts are made: (1) system analysis, (2) studies on devices and materials, and (3) installation and operation of the facilities in test buildings, and collection of the data. For the item (1), the sensible heat type heat-accumulating tank is replaced by the latent heat type to reduce heat losses and auxiliary power requirements by improving heat-accumulating tank efficiency and revising the control procedure. For the item (2), the devices installed in the test buildings are tested to improve their performance and reliability, in which, e.g., results of operation, under commercial conditions, of the Rankine cycle refrigerator installed in the test building are taken into consideration. The empirical correlation {eta} 0.66 - 1.7{delta}T/I is obtained for instantaneous heat-collecting efficiency of a vacuum collector, made on a trial basis. Its heat loss is sufficiently small, which is in agreement with the results of the nighttime heat release tests. For the latent heat type heat-accumulating tank, stability of the materials therefor are investigated. For the Rankine cycle refrigerator, development of its parts is continued. For the item (3), the facilities are tested for around 7 months, and problems involved in each device are clarified. (NEDO)

  11. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 1); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 1 Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the 'techniques for recovery and conversion of unutilized energy'. The R and D on waste heat recovery and conversion for chemical plants designs an internal structure of the 'wetted wall column for shell side as the stripping section' for increasing quantity of heat exchanged inside, and stably operates the bench plant for 100 hours or more. The R and D on thermoelectric power generating systems using low calorie exhaust gases involves development of materials, production of fine particle materials and sinters, and evaluation of their functions, among others. The program for application of the techniques to commercial plants confirms applicability of a 3kg thermoelectric power generating system to automobile coating process. The R and D on systems for thermoelectric recovery of low-temperature waste heat finds cracks on the ceramic plate for the power generating system WATT100, disassembled for repair. (NEDO)

  12. Reports on 1979 result of Sunshine Project. R and D on solar cooling/heating and hot-water supply system (R and D on system for multiple dwelling); 1979 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Shugo jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    This R and D was intended to develop the following technologies for the purpose of putting into practice an innovative system that performs cooling/heating and hot-water supply for a multiple dwelling economically by solar energy: development of equipment constituting solar cooling/heating and hot-water supply system, and development of a system which uses such equipment and which is inexpensive and safe as well as easy for inspection and maintenance. In fiscal 1979, a study was implemented in which emphasis was placed on the experiment of a test housing with a solar cooling/heating and hot-water supply system incorporated for the purpose of proving the results of the research since fiscal 1974. In the overall flow of this project, the following research contents were partially performed or being performed successively during the period of seven years. (1) Examination of various methods, (2) Development of thermally driven freezer, (3) High performance heat collecter, (4) Heat storage device, (5) Types of multiple dwelling suitable for solar energy utilization, (6) Construction of experimental multiple dwelling, (7) Experiment in houses actually in use by people, (8) Confirmation of system improvements and results on the basis of experimental measurements, and (9) Evaluation as a solar system for multiple dwelling. (NEDO)

  13. FY 1998 report on the results of the R and D of industrial science technology. R and D of 'carbon-base high functional material technology' (R and D of the submarine oil production support system); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu (kaitei sekiyu seisan shien system kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    For the R and D of carbon-base high functional materials, the paper reported on (1) material creation technology and (2) creation of mechanically high functional materials. In (1), the synthesis of new BCN-base materials is conducted by the electronic excitation CVD method and high temperature/high pressure (explosive synthesis) with the aim of analyzing the composition/structure. Using energy-controlled ion beams and laser beams, the synthesis of new CN-base materials and analysis of composition/structure are aimed at. By the thermal CVD method using catalysts, a method to synthesize a quantity of nanotubes is aimed at. The paper is aimed at clarifying the reaction mechanism on the material conversion of carbonaceous materials relating to the above-mentioned three methods and the appearance mechanism of characteristics of carbonaceous materials. (2) is composed of the following three subjects: composition gradient film formation technology, complicated shape film formation/micro-processing technology, and large area film formation. These three subjects were studied to positively make use of characteristics such as low friction/low abrasion and high temperature corrosion resistance which can be expected in amorphous carbon, diamond and high functional carbon materials of carbon nitride and to apply them to moving parts of various industrial machines and surface protection of construction materials such as glass, etc. (NEDO)

  14. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Third year report. R and D of high grade/low cost mold for rubber/plastic; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Gomu plastic yo kohin'i tei cost kanagata no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    The development was proceeded with of technology to reform the surface of rubber/plastic use mold by ion engineering technology so that the product can be easily taken out without being stained by the material. Concretely, PBII (plasma-based ion implantation) device with high ion implantation efficiency was developed, and surface reforming conditions were studied. Then, from the test using the actual device, the surface reforming technology optimum to mold releasing and mold staining resistance as rubber molding was established. Studies were made of the following: 1) establishment of the optimum mold surface reforming technology; 2) establishment of the mold surface treatment technology using PBII device; 3) improvement of PBII device and optimization of implantation method. In 2), by the surface treatment by implanting nitrogen and fluorine ions into hard chromium plating and aluminum alloys using PBII device, treatment effects were recognized in implantation ability into 3D shape, mold staining resistance and mold releasing in the hard chromium plating treated mold. (NEDO)

  15. Achievement report for fiscal 1992. Research and development of ceramic gas turbine (Study on its adaptability with society); 1992 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Shakai tekigosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    With an objective to attain a guideline for putting ceramic gas turbine (CGT) into practical application, conceptual discussions on the CGT based industrial cogeneration system (CGS) and the CGT based CGS simulations were performed to discuss quantitatively the effects of the system introduction, and estimate latent markets based on the result of calculating the introduction effects. In addition, investigations were carried out on Germany as the advanced nation with regard to the systems according to utilization patterns, load profiles, operation cost, exhaust gas measures, and the related laws and regulations. The activities may be summarized specifically as follows: 1) putting the back-data for industrial energy demand into order; 2) calculation of CGT introduction effects in industrial areas; 3) discussions on latent demand and social adaptability of CGT in the industrial area; and 4) investigations in overseas countries. Item 2 is composed of the conceptual design of industrial CGT/CGS, and the simulations on the actual status of energy demand in industrial business operation centers and on the effects of the industrial CGT/CGS. (NEDO)

  16. Report on survey/research on energy-related elementary techniques; Energy kanren yoso gijutsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The survey/research project is implemented for establishing environment-compatible energy systems in urban areas by constructing wide-area heat supply networks to exchange energy among cities. This project studies, taking Kanagawa Pref. as the model area, distributions of unutilized energy sources, and possibilities of their utilization for heat supply. There are large quantities of unutilized energy, including waste heat from power plants, general works and cleaning works, and low-temperature waste heat from, e.g., sewage and pumping systems. The district air conditioning promotion areas are selected from those consuming large quantities of heat energy in the prefecture, and their characteristics are grasped. The effects of the networks on total energy consumption of the entire prefecture are estimated for the cases of introducing the district air conditioning systems or wide-area heat supply networks in these selected areas. Introduction of optimum advanced heat utilization systems in stereotyped areas is also considered, in order to predict the effects of introduction of wide-area heat supply networks. (NEDO)

  17. Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

  18. Fiscal 2000 report on results on development of technology for reducing electrical power consumption at standby time and on R and D of energy saving fixing system; 2000 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Sho energy teichaku system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In reference to 20 to 40 cpm letter size monochrome digital copiers, R and D was conducted for the purpose of developing an energy-saving fixing system by the combination of a thin-layer thermal-roller fixing unit and a low-fixing-temperature polymerized toner, with the fiscal 2000 results compiled. In the development of the thin-layer thermal-roller fixing unit, a fixing system suitable for toner characteristics was completed, through the optimization of a temperature-stabilizing cooling fan and by a mechanism for detecting anomalous high temperature at the time of a runaway heater, for example. In the research of the low-fixing-temperature polymerized toner, efforts were made toward improving somewhat weak electrostatic chargeability, which was a conventional problem in toner characteristics, and enhancing the thermal/mechanical durability of the toner. In the method of improving electrostatic chargeability, a new process was developed capable of effectively functioning additives in a toner, attaining a level practically free from problems. In the heat resisting characteristic, its enhancement was achieved by developing a method that checks no fused fixing performance at the time of heating for fixing and that imparts a new heat resistivity to a latex surface layer less susceptible to heat inside a copier. (NEDO)

  19. Achievement report for fiscal 1998. Research and development of new technologies for storing farm products utilizing low-temperature energy (2nd fiscal year); 1998 nendo seika hokokusho. Teion energy wo riyoshita nosanbutsu no shinki chozo gijutsu no kenkyu kaihatsu (dai 2 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim of the work was to create new industrial technologies utilizing low-temperature energy satisfying local needs through developing new technologies, including air conditioning technologies high in reliability and excellent in energy efficiency. The objectives of the effort were to elucidate the behavior of moisture in the atmosphere below the freezing point and to develop farm product preserving technologies, to develop highly efficient energy conversion technologies for use in the low-temperature zone, latent heat storing cold heat technologies, and system evaluation. Constructed in connection with the last-said system evaluation were three technologies, which were a below-zero high-humidity air conditioning technology based on the outcome of agricultural verification of farm product storage, energy-efficient low-temperature storage of farm products which was a combination of a low-temperature oriented energy-efficient energy conversion technology and a clathrate hydrate-aided cold heat storing technology, and a technology applicable to business in the low-temperature processing field accessorial to the said technologies. They were compared with the conventional technologies, and then it was found that the most energy-efficient system, as endorsed by a 40-50% reduction it caused in electricity rate, was a combination of a low-temperature storage, frozen food storage, hydrate cold heat storage tank, recovery facility for farm waste incineration-produced waste heat, and a pulse tube freezer. (NEDO)

  20. Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on Si ribbon crystal vertical pulling method); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Silicon tatehiki ribbon kessho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-30

    This research includes (1) basic study on Si ribbon crystal vertical pulling method, (2) basic design of continuous Si ribbon crystal vertical pulling mechanism, (3) basic study on vertically pulled Si ribbon crystal, (4) study on capillary materials for capillary crystal pulling method, and (5) basic study on AlAs-GaAs system compound semiconductors. In the 1st research, for Si ribbon crystal vertical pulling growth, the ribbon crystal pulling equipment was prepared and modified, and Si crystals were obtained by capillary and web methods. In the 2nd research, for development of Si ribbon crystal vertical pulling growth technology, study was made on the simple energy-saving resource-saving continuous automatic production process. In the 3rd research, measurement was made on various characteristics of ribbon crystals. In the 4th research, study was made on requirements of capillary materials from the viewpoint of capillary growth mechanism. In the 5th research, basic technology for solar cell production was established through growth experiments of AlAs-GaAs mixed crystals and multiple epitaxial crystal layers. (NEDO)

  1. Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation - 1 (Promotion of international cooperation); 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu seika hokokusho. 3. Kokusai kyoryoku ni kansuru chosa kenkyu - 1 (kokusai kyoryoku suishin no tame no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    International research cooperation was promoted and technical information was internationally exchanged for the development of the International Clean Energy Network Using Hydrogen Conversion (WE-NET) Project into a truly international cooperation project. In the promotion of international research cooperation, a collection of summarized achievement reports for fiscal 1999 translated into English, based on achievement reports on the respective tasks, was disseminated to 157 related organizations overseas. Activities related to the WE-NET Project were actively presented at international conferences. For research cooperation at IEA (International Energy Agency), engineers were dispatched to its committees and annexes specializing in hydrogen related implementation agreements. In the international exchange of technical information, overseas surveys were conducted for fulfilling the purposes of the respective WE-NET tasks. Investigations were conducted into the latest fuel cell development status across the world, not to mention the automotive fuel cell now attracting earnest attention. Moreover, surveys were conducted of hydrogen energy related research institutes abroad, and a Japanese booth was installed at Hyforum 2000 (The International Hydrogen Energy Forum 2000). (NEDO)

  2. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

  3. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

  4. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research on amorphous silicon defect density); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (Amorphous silicon no kekkan mitsudo no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    So as to determine the energy distribution of defect level density in a-Si, which is indispensable for an optimum solar cell design, the hitherto unclear theoretical relationship between the field effect method and MOS (metal oxide semiconductor) capacity method is made clear, and a unified theory is newly established. A high-speed totally automatic evaluation system is developed, capable of high-accuracy determination of defect levels. For the realization of an a-Si MOS structure required for fulfilling the above purpose, a-Si is grown and then diborane and ammonia are subjected to a glow discharge decomposition process for the formation of a new insulation film. It is found that the material may be utilized for MOS structure construction for defect density evaluation. Studies are conducted on plasma emission spectroscopy and infrared absorption analysis for the elucidation of growth mechanism for the growth of high-quality a-Si. Key radicals in plasma that govern film growth are investigated. It is disclosed that excited hydrogen in plasma plays an important part in microcrystalline phase deposition. It is also disclosed that hydrogenation greatly improves on CVD (chemical vapor deposition) a-Si doping efficiency. (NEDO)

  5. Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

  6. NEDO Forum 2000. Industrial technology development session; Sangyo gijutsu kenkyu kaihatsu session

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    This session presented the following subjects: I. IT innovation, II. Bio-seminar, III. Nano-technology, IV. Machine technology seminar, and V. 'Development subsidy project to put industrial technologies into practical use'. The theme in I relates to (1) influence of IT innovation on the society, (2) the theory of semiconductor evolution, (3) the theory of liquid crystal evolution, and (4) the theory of disk evolution. The theme II searches (1) how far have bio-technologies come?, (2) search of human evolution from genes, (3) can human being live up to 150 years by bio-technologies?, and (4) what is a DNA array (chip)?. The theme III covers (1) product innovation in polymers (new polymeric materials brought about by polymer nano-technology, taking polyolefin as an example), and (2) creation of ceramics materials by using nano-technologies. The theme IV relates to (1) ITS changes the car society into this way, (2) the current status and outlook on research and development of micro-machine technologies, and (3) the futuristic society and new industries opened by the Humanoid project. The theme V describes (1) practical application of ultra-small medical device production technologies, (2) development of next generation semiconductor manufacturing resists, (3) development for practical application of an optical brain function imaging device, and (4) development for practical application of new screening technologies toward creation of medicines using genome. (NEDO)

  7. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  8. FY 1991 Report on research and development of super heat pump energy accumulation system. Material for explanation (Construction and operation of the prototype system - researches on elementary techniques and construction and operation of the pilot system); Super heat pump energy shuseki system no kenkyu kaihatsu 1991 nendo seika hokokusho. Setsumei shiryo (system shisaku unten kenkyu (yoso gijutsu no kenkyu / pilot system no shisaku unten kenkyu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-05-01

    Summarized herein are R and D results of the researches on the super heat pump energy accumulation system, obtained from FY 1985 to 1991. For R and D of the super high performance compression heat pumps, the R and D results of the elementary techniques and bench and pilot plant operation are summarized for the highly efficient type (for heating) and highly efficient type (for cooling and heating), and high temperature type (utilizing high temperature heat source) and high temperature type (utilizing low temperature heat source). Described are patent application list, designated know-hows, and conclusions. For the elementary equipment and working fluids, the R and D results are summarized for the evaporators for mixed solvents, EHD condensers, and working fluids (alcohol-based fluids and application characteristics of new fluids) and working fluids (nonalcohol-based fluids and basic properties of new fluids). For the chemical heat storage techniques, the R and D results are summarized for the high temperature heat storage type (utilizing metathesis reactions, ammonia complexes and hydration reactions), and low temperature heat storage type (utilizing clathrates, hydration by solute mixing and solvation). (NEDO)

  9. Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Thermoelectric energy recovery system for automobile; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Jidoshayo netsuden energy kaishu system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project aims to develop a system for recovering heat from the thermal energy of automobile exhaust in the form of electric energy. Skutterudite based thermoelectric materials for high temperature use and existing thermoelectric materials for low/middle temperature use were improved in performance, and a dimensionless thermoelectric performance index of ZT=1 was attained. Advanced processes were applied for improvement on the performance of existing thermoelectric materials. In the effort to develop technologies for the mass production of thermoelectric materials for high temperature use, a material manufacturing process was established for manufacturing materials excellent in thermoelectric and mechanical properties using a method for mass-producing sinterable materials by gas atomization and a large discharge plasma sintering process capable of treating large specimens. In the effort to improve automobile power generation modules in performance and to establish element technologies for their manufacture, technologies were developed involving thermoelectric materials and electrodes, bonding of different thermoelectric materials, bonding of heat conducting electrical insulators and electrodes, and high efficiency segment type power generation modules. A high performance automobile exhaust gas heat exchanger was developed. A Co-Sb based thermoelectric module and a Bi-Te based module were combined and the package was tested aboard automobiles, when a maximum power output of 83W was achieved. It is necessary to review module arrangement. (NEDO)

  10. Achievement report for fiscal 1998 on the research and development of genome informatics technology. Development of energy use rationalization technologies; 1998 nendo genome informatics gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the field of the analysis of gene expression frequency information, a novel glass coating method and a highly sensitive high-speed reading device are developed. Element technologies are studied for the development of a detection system capable of high-density high-speed reading of high-density DNA capillary array, with a long-chain DNA probe solidified therein. In the technology of transcription control information analysis, concerning the technology of transcription dynamics analysis using tagged transcription control factors, the construction of a model system protocol is studied, an automatic analysis system is developed, and an evaluation technology is also developed. Furthermore, a novel method is proposed, in which two specimens will be prepared, that is, a microbead coupled DNA specimen consisting of base sequences of all combinations of a certain chain length and a cDNA (complementary deoxyribonucleic acid) derived protein specimen, and DNA-protein complexes will be isolated for analysis bead by bead out of a liquid which is a mixture of the said two specimens. (NEDO)

  11. NEDO Forum 2001. Session on development of energy and environmental technologies (For promotion of comprehensive development of hydrocarbon-based energy); NEDO Forum 2001. Energy kankyo gijutsu kaihatsu session (tanka suisokei energy no sogo kaihatsu suishin no tame ni)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Pointed out in a lecture entitled 'How technology development for hydrocarbon-based energy resources should be' was the need of technologies for clean energy production; CO2 emission reduction; NOx, SOx, soot, and dust reduction; and the expansion of exploitation of resources now left unused. Reported in a lecture entitled 'Cooperation with China on coal liquefaction' were the result of a coal liquefaction demonstration plant feasibility study conducted for coal from Inner Mongolia, and so forth. Reported in a lecture entitled 'Development of coal oil upgrading technology' were the result of the operation of a test plant, and so forth. Reported in a lecture entitled 'Research and development of HyperCoal' were the result of HyperCoal manufacturing technology research and development, designing of a HyperCoal-fired gas turbine power generation system, and so forth. In addition, development of technology for high efficiency conversion of biomass energy and development of technology for refuse gasification/melting power generation were reported. (NEDO)

  12. マルクスの「現実の資本の過剰生産」概念について

    OpenAIRE

    松尾, 純; Jun, Matsuo; 桃山学院大学経済学部

    2008-01-01

    Professor Noriko Maehata and I have been engaged in discussions concerning the understanding of the concept of "actual overproduction of capital" as contained in Karl Marx's Das Kapital Volume III. The discussion originated in Professor Maehata's criticism("'Law of the Tendency of the Rate of Profit to Fall' and 'Absolute Overproduction of Capital' - An Issue in Research on the Theory of Crisis," Economic Society of Rikkyo University(Rikkyo Keizai Gaku Kenkyu), Vol. 55, No. 1, July 2001)of my...

  13. Report on the results of research and development under a consignment from NEDO on deca-nano quantum integrating transistor substrate technologies; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Deca-nano ryoshi shusekika soshi kiban gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Researches have been conducted on deca-nano quantum integrating transistor substrate technologies, and developments were made on a three-dimensional device simulator which can be used in deca-nano domains, and a circuit simulator to have quantifying function transistors coexist with silicon semiconductor integrated circuits. The researches were intended to develop a simulator capable of analyzing properties of very small silicon and compound semiconductor devices in deca-nano domains. The researches discussed the applicability of conventional simulators, calculated quantum levels in a three-dimensional hetero structure, and resulted in development of an electron wave propagation simulator in optional two-dimensional shapes, a quantum Monte Carlo simulator, and a three-dimensional semiconductor device simulator with quantum correction. On the other hand, in order to estimate characteristics of a hybrid circuit in which single electron transistors coexist with conventional transistors such as CMOS transistors, a single electron hybrid circuit simulator was developed. The development indicated that a CMOS-SET fused memory is promising as a future LSI memory. 22 refs., 116 figs., 3 tabs.

  14. Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

  15. Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology (R and D of the monitoring system using high-intensity X-ray pulse for power plants); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (kokido X sen pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the result on R and D of the femtosecond technology in fiscal 1997. Ultrahigh-speed electronic technology is indispensable for industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. In R and D of metrological technology using ultra-short light-pulses, study was made on generating and controlling technology for ultra- short light/electron beam pulses. Ti-sapphire mode-locked laser was prepared, and it was found that time-fluctuation of mode-locked laser pulses is measurable up to 100 femtosecond level. As measures against an instability of gain-switching semiconductor laser, light injection from the outside was effective. The stable directivity of laser beam was obtained by regenerative amplifier, while less temperature variation of an optical switch was necessary to stabilize energy. To generate femtosecond high-intensity X-ray pulse by collision of laser and electron beams, it was confirmed that sub- picosecond synchronization is possible by RF and picosecond laser synchronization circuit. 48 refs., 89 figs., 11 tabs.

  16. Report on achievements in fiscal 1999. Research and development of synergy ceramics (research and development of technologies to prevent corrosion in petroleum production systems); 1999 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research and development has been performed on the following themes: 1. Material realizing technology, and advanced evaluation and design technology (1-(1) ultra precision materials, 1-(2) high-temperature energy materials, 1-(3) basic member design technology, 1-(4) materials having function to detect stresses and micro destruction, 1-(5) porous materials to control gas hole patterns, and 1-(6) materials having self-restoring/self-lubricating function); 2. Application technology (2-(1) materials having substance and light selecting function, 2-(2) high wear resistant and easy-to-process materials, 2-(3) high-performance resistance materials for electric power devices, and 2-(4) flexible sliding materials); 3. Formation of common base technologies. 4. Report on achievements in countries making joint researches. In Item 1-(1), micro destruction mechanisms were analyzed, and the directionality of material structure control was clarified. In Item 1-(2), controlled closing holes were introduced. In Item 1-(3), polycrystalline alumina, polycrystalline zirconia, and zirconia particle dispersed alumina were evaluated microscopically and macroscopically. In Item (4), Y-TZP/Ni nano-compound materials were fabricated successfully. In Item 1-(5), destruction behavior of porous ceramics was studied. In Item 1-(6), characteristics were investigated on Fe(Al)Al2O3 which was fabricated on the trial basis. (NEDO)

  17. FY 1998 annual report on the research and development of advanced ceramic gas turbines. Study on social adaptability; 1998 nendo senshingata ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Shakai tekigosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The New Sunshine Project, promoted by Ministry of International Trade and Industry, has developed a 300 kW ceramic gas turbine CGT302 (biaxial, regenerative type) in March 1999, which attains a turbine inlet temperature of 1,334 degrees C and thermal efficiency of 42.1%. The conditions of optimum utilization of the system are studied for eventual commercialization and spread of these systems, including analysis of load types for specific purposes, prediction of operation management, economics of CGT, environmental impacts, and possibility of diversification of the fuel. The CGT cost analysis results indicate that a CGT system is well viable when the incremental initial cost of the power generator is kept below 70,000 yen/kW over the conventional system. The system can be doubled in scale at the largest. It can be further scaled up, when hybrid members with metallic materials are used. CGT is a basic technique for (system energy). In other words, the 21st. century will be the age of (system energy), i.e., (gas turbine). (NEDO)

  18. Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of solar energy technologies (Research and development of SnO{sub 2} solar cells); 1981 nendo taiyo energy gijutsu no kenkyu kaihatsu seika hokokusho. SnO{sub 2} taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    The aim is to establish the technology of manufacturing SnO{sub 2}/nSi solar cells using a low-temperature deposition method and thereby to reduce the cost. A 5cm-diameter wafer is subjected to a batch process, and a large-area, uniform-quality SnO{sub 2} film is obtained. A conversion efficiency of 13.7% is achieved for a single-crystal 9cm{sup 2} cell. As for the conditions of electrode formation, conventional methods are applied for bonding metals, which are Sn, Ni, Zn, etc., for the surface electrode and rear electrode. Vapor deposition is found to be the most excellent. Since it is known that ohmic characteristics improve when Cr is inserted as the base for the surface electrode rear electrodes, it is anticipated that a contact resistance value not inferior to that by vapor deposition will be achieved once the method of Cr bonding, whether by printing or plating, is established. An n-type low-cost polycrystalline Si substrate is subjected to etching under the optimum conditions, and a conversion efficiency of 9.6% is achieved for a 0.5cm{sup 2} cell. An SnO{sub 2} film is formed on a uneven surface for a reduction in the single-crystal cost, when characteristics better than those of a wafer manufactured by surface polishing are realized. Experimentally produced cells are evaluated using a solar simulator, and the result indicates that the electrode forming conditions influence conversion efficiency a great deal. (NEDO)

  19. FY 2000 report on the results of the regional consortium R and D project - Regional consortium R and D. Second year report. R and D of a high functional mini production system for small precision machine parts; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki cosortium kenkyu kaihatsu. Kogata seimitsu kikai buhin'yo kokino mini seisan system no kaihatsu kenkyu (dai 2 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Judging that it is the most desirable to use processing systems suitable for product sizes from viewpoints of resource conservation, space saving and energy conservation, the development was proceeded with of machine tools for small precision machine parts (mini production cell). The size of cell is 200x200x200mm, and the working accuracy of the same level as that of the existing machine was targeted. Studies were made in the following 6 fields: 1) development of a total system; 2) design/manufacture/evaluation of mini cell; 3) evaluation of grinding processing cell (first phase) and accuracy control technology; 4) development of small sensor; 5) analysis/evaluation of element cell; 6) study on the basement technology of mini production system. In 2), study was divided into the following: development of grinding processing cell; development of grinding processing cell (second phase); processing performance test; structural analysis. In 6), study was divided into the following: outline of the study; study on micro plasticity processing; study on active type control of the removal amount; robust process design of mini production system. (NEDO)

  20. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

  1. Achievement report for fiscal 2000 on research and development of key technologies for superconducting generator. Research and development of key technologies to increase density, research and development of key technologies to increase capacity, research and development of design technologies, and research of technologies; 2000 nendo chodendo hatsudenki kiban gijutsu kenkyu kaihatsu seika hokokusho. Komitsudoka kiban gijutsu no kenkyu kaihatsu / daiyoryoka kiban gijutsu no kenkyu kaihatsu / sekkei gijutsu no kenkyu kaihatsu / gijutsu chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Researches have been made to increase density of 200,000-kW class generator and to increase capacity of 600,000-kW class generator necessary for putting superconducting generator into practical use. This paper summarizes the achievements in fiscal 2000. In the study of increasing densities of superconductors and field windings, strands were fabricated, in which aging heat treatment conditions, number of aging, and processing degrees between each aging were varied, to increase the critical current of Nb-Ti strand, wherein as high critical current as corresponding to about 90% of the target was obtained. Possibility of increasing the critical current with the final processing degree in the range of 4 to 5 was verified from the relationship between the final processing degree and the critical current. In the study of increasing capacities of superconductors and field windings, findings were acquired on enhancement of conductor stability and reduction in AC loss, with regard to superconductor strands well balanced in the two elements. Prospects were obtained in achieving the AC loss of 200 kW/m{sup 3} in the targeted superconductor. The residual resistance ratio was found to be 200, showing sufficiently high value, and sufficient function was verified in the stabilized copper. In the research of design technologies, primary basic design was performed. (NEDO)

  2. Survey report of FY 1997 on the long-term energy technology strategy. Survey on the pre-assessment system of energy and environmental technology research and development; 1997 nendo chosa hokokusho (choki energy gijutsu senryaku chosa). Energy kankyo gijutsu kenkyu kaihatsu no jizen hyoka ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To select projects of the New Sunshine Program which is the locomotive for Japan`s research and development of energy and environmental technologies and to map out the Program`s long-term strategy, it is required to develop an effective methodology of assessing research and development themes. It is also necessary to establish the pre-assessment system which makes the assessment process more logical and which will enable the priority setting among different themes on the basis of objective and quantitative analysis. Additionally, transparency should be ensured for such a pre-assessment process through disclosure to the public and other means. The present survey aims to concretize the pre-assessment system by studying the system and techniques of an assessment system which is applicable to the research and development themes of the New Sunshine Program and is objective, quantitative and logical and which can ensure transparency and by receiving suggestions on the pre-assessment of Japan`s research and development of energies and environmental technologies through research on overseas trends of government-led research and development. 3 refs., 7 figs., 26 tabs.

  3. Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 5. Development of hydrogen vehicle system; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 5. Suiso jidosha system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on the safety of hydrogen absorbing alloy tanks for hydrogen vehicle systems and the measuring method of a fuel consumption rate of hydrogen fuel cell powered vehicles. In the impact rupture test of (mini-scale) hydrogen absorbing alloy tanks, the impact 3-point bending test result by drop weight showed no ignition caused by impact and friction energy acting on hydrogen released by rupture of tanks, and the necessity for taking spontaneous ignition of alloys due to fuel leakage into account. The experiment result on deformation and rupture of alloy tanks caused by expansion and contraction of crystal lattices due to hydrogen absorption and desorption showed relatively large deformation due to grain fining only within earlier 10 cycles, and no cracks nor other defects even after 1000 cycles. In the measurement of a fuel consumption rate of hydrogen fuel cell powered vehicles, the study result on flow rate measurement method, full tank method, electric current method, hydrogen balance method and oxygen balance method showed that the electric current method is most simple, accurate and practical. (NEDO)

  4. Achievement report for fiscal 1996 on the research and development of superconductor technology to power generation. Pt. 1. Research and development of superconducting wire, generator, total system, and refrigeration system; and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    In the research and development of superconducting wires, studies are conducted to increase the current capacity of NbTi and Nb{sub 3}Sn metal wires and to improve their properties, and to increase the current capacity of oxide materials and improve their performance making full use of the features of each manufacturing method. In the development of superconducting generators, a slow excitation response type is tested for verification, and a good result is attained; and a quick excitation response type is tested for field winding static excitation, and good performance is exhibited. Using the results so far achieved, the 200,000kW class pilot machine concept design is reviewed. In the study of total systems, feasibility is studied of a quench test for the 70,000kW class machine through simulation analyses, etc. In the development of refrigeration systems, efforts are exerted to improve on the conventional type in terms of reliability and to further improve on the improved version in terms of performance and space-saving feature. One of the endeavors involves the development of a He Brayton cycle turbine driven compressor. A multilayer cylindrical rotor is verified in terms of functions, characteristics, reliability and durability, and various data are collected toward the development of a pilot machine. (NEDO)

  5. Fiscal 2000 achievement report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Research and development of nanometer-order controlled material creation process technology); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu (nanometer order de seigyo sareta material sosei process gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop tribo-material creation process technologies capable of meeting the needs of environmental protection and energy conservation relative to automobile engine parts such as piston rings, cams, shims, and the like. Activities are conducted in the three fields of (1) the research and development of nanostructure material creation technologies, (2) research and development of tribological evaluation technologies, and (3) the verification of the developed technologies. In field (1), a nanostructure control process is studied, and tribo-composite materials are examined. In field (1), in fiscal 2000, the arc ion plating method is selected as a nanostructure control process, and the closed type nonequilibrium magnetron sputtering method as the base for development into a process. As for tribo-composite materials, Ti-Si-N based and Cr-Si-N based coatings find their feasibility in shims, and Cr-Si-N based and Cr-Si-C-N based coatings in piston rings. Compiled in this report are the summary, and the studies of nanostructure control process technologies, joint studies, composite ceramic coating practicalization technologies, and technologies for putting to practical use coatings which comprise layers of different substances. (NEDO)

  6. Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

  7. Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

  8. Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of microfactory technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to save energy and minimize the working space by constructing a manufacturing system comprising various micromachines with their dimensions fit for parts and products they handle. Development continues relative to microprocessing (electrolysis, and optical processing) and microscopic liquid operation (micropump, and part holding device). Under research in relation to the assembly process are a micro-arm to handle tiny parts and precision techniques for interfitting within a very small microfactory, a piezoelectric actuator for microscopic position adjusting, and ultraprecise microprocessing techniques indispensable for their manufacture. Also under research are the incorporation of optically driven microdevices developed before the preceding fiscal year into a microfactory and the study of microservo actuators capable of sophisticated positioning and velocity control. Concerning the microscopic transport system to deal with microscopic parts and products, studies are under way so as to embody systems driven by actuators of the electromagnetic type and electrostatic type. In this paper, reference is made to inspection techniques and comprehensive investigations. (NEDO)

  9. Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

  10. Japan-EU joint research project on petroleum substituting energy; Nichi EU sekiyu daitai energy kanren kyodo kenkyu jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Four EU research workers were invited from Portugal, Italy and France for promoting R & D of petroleum substituting energies in Japan. The joint research on the wide area energy use network system (advanced district cooling and heating) includes the experimental technology for measuring heat transfer acceleration and drag reduction, evaluation of rheological characteristics of fluid, and development and selection of an adequate composition equation of fluid. The joint research on MCFC includes the test method and procedure of components and cells in relation to corrosion by molten carbonate, elution of NiO cathodes, electrode modeling and alternative materials for cathodes. The joint research on geothermal gases includes the research method of fumarolic gases such as volcanic gas and geothermal gas, applications in Italian geothermal fields and the relation of geothermal gases with the origin of fluid, deep conditions and volcanic activity. In addition, the joint research on light energy conversion (energy transfer system between binuclear metal complexes) and the performance and use of metal complexes as catalyst for polymer electrolyte fuel cells was also performed. 52 refs., 20 figs., 3 tabs.

  11. Report on technological achievements in fiscal 1999. Institutions for research and development of new environmental industry creating type technologies (Development of hybrid construction machines); 1999 nendo shinki kankyo sangyo soshutsugata gijutsu kenkyu kaihatsu seido seika hokokusho. Hybrid kensetsu kiki no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Energy efficiency of construction machines is extremely low, because engines cannot follow sudden load changes. Solution is sought by developing a construction machine using as the motive force source a hybrid unit composed of an engine, a generator and batteries. The activities were advanced in the following five fields: (1) analysis on loads on existing construction machines, (2) development of hybrid move force unit, (3) development of an actuator device, (4) development of a control system, and (5) development of a hybrid construction machine simulating system. In Item (1), a control work on a 6-ton class hydraulic shovel was selected as a representative work, whereas the work was divided into seven modes to measure such output characteristics as fuel consumption and actuator output in each work, and the standard work load modes were established. In Item (2), motive force in the set load modes was measured to discover functional requirements on the motive force unit. In Item (5), the simulation model for the existing machines was used to evaluate the fuel consumption performance of the motive force unit. (NEDO)

  12. Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

  13. Research and development of peripheral technology for photovoltaic power systems. Research on engineering methods for cost effective PV installation; Shuhen gijutsu no kenkyu kaihatsu. Tashu secchi koho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of engineering methods for photovoltaic power system installation in fiscal 1994. (1) On the survey on applicable fields, various application aspects, applicability, and problems on location and legal regulation were continuously studied for railway, river reservation, lake surface and public facility as promising locations after highway in the last fiscal year. The result pointed out relatively easy possibility of PV power generation of nearly 11,700MW except residence and building fields. (2) On installation technology of solar cell arrays, several models based on various installation conditions, construction methods and system configurations were studied, and various application aspects were proposed by combination of simple design conditions. (3) On test and evaluation of the structural design of array racks, wind tunnel experiments were conducted for structure wall, platform shed and highway sound insulation wall. (4) On basic design of various promising systems, the conceptual design of interconnection systems was carried out assuming applications to highway and railway. 7 figs., 3 tabs.

  14. Reports on 1979 result of Sunshine Project. R and D on solar cooling/heating and hot-water supply system (R and D on system for large-sized building); 1979 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Ogata kenchikubutsuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-31

    In fiscal 1977, studies were carried out jointly with a research group assigned by the Government Research Institute using a solar cooling/heating and hot-water supply system for a large-sized building (i.e., various devices such as a heat collecting device, heat storing device, refrigerator, etc., and their attached equipment, hereinafter the 'test equipment'), a system installed in the building of the energy technology section, Department of engineering, Oita University. The studies were as follows. (1) Meteorological observation was conducted concerning meteorological items such as insolation, temperature, wind direction and wind velocity which were necessary for the operation and evaluation of the test equipment. (2) The test equipment was operated by the Oita University technical assistants in cooperation with the research group so that R and D was smoothly carried out for the practicability of an innovative system, in which cooling/heating and hot-water supply for a large-sized building were economically performed by the solar energy using the test equipment; and also, maintenance and management for the overall facilities were carried out within a pre-determined range. (3) Temperature, wind velocity, etc., around the heat collecting device were continuously measured in the winter time for preventive measures against freezing, with the data accumulated. The facilities consisted of 40 units of 2 m x 7.5 m large heat collecting device, 30USRT absorption refrigerating machine, and 45 m{sup 3} heat storage tank. (NEDO)

  15. FY 2000 report on the results of the supplementary project for the development of energy utilization rationalization technology. Leading study for the development of high efficiency thermoelectric converter; 2000 nendo energy shiyo gorika gijutsu kaihatsu hojo jigyo seika hokokusho. Kokoritsu netsuden henkan soshi kaihatsu sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    For the purpose of energy conservation and environmental protection by effective utilization of unused waste heat, the R and D of thermoelectric conversion technology were conducted, and the FY 2000 results were summed up. In the investigative study of thermoelectric converting materials, evaluation was made of the materials having a possibility of achieving the target with the element efficiency of 6% and the assumed use temperature domain of 120-330 degrees C. The result of the study indicated that the number of new materials which were made public was increasing, but there were no materials that have evidently practical applicability. In the investigative study of element manufacturing technology, trial manufacture of element was made in which the investigative results were integrated into the existing 50W element manufacturing technology, and a target of 70W was achieved. In the investigative study of the thermoelectric conversion system for industrial and commercial/residential use, field survey and questionnaire survey were conducted for three fields of iron works, chemical plant and garbage disposal plant. As a result, it was found that there was a large amount of waste heat. By the study of the system conceptional design, it was found out that the output of 40-50kW can be obtained in the system structure suitable for the source of waste heat of iron works, etc. (NEDO)

  16. Research and development of utilization technology of solar thermal energy system for industrial and other use. Research and development of solar system (investigation of popular type snow melting systems); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Solar system no chosa kenkyu (fukyugata yusetsu system no kenkyu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for investigation for popular type snow melting systems using solar energy. Two types of technologies are proposed to utilize solar energy for snow melting in winter and create comfortable environments. One is combined (active plus passive) type, which transfers solar heat it collects by the whole wall surfaces to an attic to heat it totally, and makes the whole roof as a radiator to melt snow. However, heat radiated from the roof is insufficient to melt all snow on the roof, allowing it to remain to an extent that it works as an insulator. The other is active type, which transfers heat it collects by the collector to the heat storage tank, from which heat is extracted in winter for various purposes, including snow melting. Such a system must store heat for an extended period, for which a highly insulating heat storage tank is proposed to balance capacity of heat storage between seasons and building size.

  17. Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 8. Development of hydrogen production technology; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu seika hokokusho. 8. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was carried out to establish a hydrogen production technology in the electrolysis of water using the solid macromolecular electrolyte method expected to be more efficient and less costly than the conventional hydrogen production methods. In the development of large area electrolysis cell lamination, a lamination comprising ten 2,500cm{sup 2} cells was fabricated, and a value exceeding the target energy efficiency of 90% was achieved. In the fabrication of stacks for hydrogen service stations, a lamination of ten cell stacks of 1,000cm{sup 2} was built, which achieved energy efficiency of not less than 90% at the an electrolysis temperature of 100 degrees C. A hydrogen production plant conceptual design was prepared under the conditions of hydrogen generation amount: 10,000Nm{sup 3}/h, electrode area: 10,000cm{sup 2}/cell, current density: 2.5A/cm{sup 2}, operating temperature: 120 degrees C, cell voltage: 1.705V, total number of cells: 976, stack constitution: 122/stack, and the number of stacks: 8. The result of studies placed the plant construction cost at 2.18-billion yen including building and civil engineering costs, and the hydrogen production unit cost at 28.4 yen/Nm{sup 3}. (NEDO)

  18. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Chofu City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Chofu) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes investigative studies on a new at-home welfare devices. Section 2 of the document, 'Studies on electric power conservation considering living patterns of elderly and physically handicapped persons' describes verification experiments in ferro-concrete buildings and ordinary homes by using a prototype system structured in last fiscal year. Qualitative analysis was performed based on the result thereof. In the 'Surveys on working environments for elderly people', directionality was presented in improving labor environments for the elderly people. Section 3, 'Studies on emergency evacuation devices for physically handicapped and elderly people' discovered that many of the presently available evacuation devices are intended of use mainly by handicap-free people, and there are many aspects that are difficult to say that elderly and physically handicapped people are included in the field of vision. In the 'Studies on an at-home training supporting system to maintain movement functions of the legs of elderly people', design and fabrication were performed on a prototype of an external control device operated by the legs. The 'Surveys on energy demand for at-home welfare devices for elderly people', showed how much the growth of the number of utilized devices will link to the cause to push up the energy demand in the household department in Japan. (NEDO)

  19. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. Third year report. R and D of a working material processing eco system using powder mold-releasing lubricant; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Funtai rigata junkatsuzai wo mochiita sokeizai kako eco system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of constructing the industry of processing low cost/low environmental load working materials, the development was proceeded with of a block die type powder mold-releasing system. Studies were made in the following 6 fields: 1) optimization/commercialization of new adhesion/flow methods; 2) optimization/commercialization of new powder mold-releasing lubricant; 3) demonstrative experiment and optimization of an eco die cast system; 4) optimization of a powder mold-releasing forging system; 5) application test on the actual mold-releasing lubricant reduction type system; 6) comprehensive investigational study. In 1), studied were a method to integrate the profile of supply pressure of powder conveying air flow and the basic information on adhesion behavior into the practical process, and optimization of powder supply method and supply device control sequence. In 2), the development was made of a sleeve use high thermal insulation type powder mold-releasing lubricant (composed mostly of Al(OH){sub 3}, graphite and wax). This powder mold-releasing lubricant remarkably improved forging ability of the ultra-thin material with 0.4mm thickness and materials with complex shapes and markedly decreased fracture chills. (NEDO)

  20. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Third year report. Development of precision farming system combined with the autonomous vehicle for large scale agriculture; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A farming supporting system that enables autonomous driving was developed from a viewpoint that the development of super manpower saving technology including automation helps sustainable development of the Japanese agriculture. The following were conducted: development of autonomous driving vehicle, development of automated operation unit, field space mapping for precision agriculture and development of groups of PF (precision farming) work machine (weeder, controller, fertilizer applicator, harvesting machine), development of groups of field work sensor (simple soil analytical system, crop growing sensor, glass yield sensor), development of field information managing database, development of work optimized application software. The operation test on the integration system was made at the model production field. The operation experiment using fertilizer applicator, controller and autonomous driving tractor was carried out at a beet field of 2ha in the farming zone in Tokachi, Hokkaido, and the results were obtained as expected. Further, as to the precision agriculture introduced with developmental equipment, etc., 20% of the energy consumption is expected to be reduced. (NEDO)

  1. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Third year report. Development of precision farming system combined with the autonomous vehicle for large scale agriculture; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A farming supporting system that enables autonomous driving was developed from a viewpoint that the development of super manpower saving technology including automation helps sustainable development of the Japanese agriculture. The following were conducted: development of autonomous driving vehicle, development of automated operation unit, field space mapping for precision agriculture and development of groups of PF (precision farming) work machine (weeder, controller, fertilizer applicator, harvesting machine), development of groups of field work sensor (simple soil analytical system, crop growing sensor, glass yield sensor), development of field information managing database, development of work optimized application software. The operation test on the integration system was made at the model production field. The operation experiment using fertilizer applicator, controller and autonomous driving tractor was carried out at a beet field of 2ha in the farming zone in Tokachi, Hokkaido, and the results were obtained as expected. Further, as to the precision agriculture introduced with developmental equipment, etc., 20% of the energy consumption is expected to be reduced. (NEDO)

  2. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Chofu City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Chofu) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes investigative studies on a new at-home welfare devices. Section 2 of the document, 'Studies on electric power conservation considering living patterns of elderly and physically handicapped persons' describes verification experiments in ferro-concrete buildings and ordinary homes by using a prototype system structured in last fiscal year. Qualitative analysis was performed based on the result thereof. In the 'Surveys on working environments for elderly people', directionality was presented in improving labor environments for the elderly people. Section 3, 'Studies on emergency evacuation devices for physically handicapped and elderly people' discovered that many of the presently available evacuation devices are intended of use mainly by handicap-free people, and there are many aspects that are difficult to say that elderly and physically handicapped people are included in the field of vision. In the 'Studies on an at-home training supporting system to maintain movement functions of the legs of elderly people', design and fabrication were performed on a prototype of an external control device operated by the legs. The 'Surveys on energy demand for at-home welfare devices for elderly people', showed how much the growth of the number of utilized devices will link to the cause to push up the energy demand in the household department in Japan. (NEDO)

  3. Report on research achievement in relation with developing fundamental combustion control technologies in fiscal 1998. Research and development of high-performance industrial furnaces; 1998 nendo nensho seigyo kiban gijutsu no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Development is intended to be made on fundamental combustion control technologies applicable to high-performance industrial furnaces that can reduce energy consumption and respond to environment preservation requirements. With an intention to achieve reduction in combustion exhaust gases such as carbon dioxide and nitrogen oxides, fundamental studies will be made on factors to decide flame shapes as represented by high-temperature combustion and flame shape control by utilizing microgravity environment, and researches will be made on combustion systems. Devices required for the experiments were fabricated to evaluate critical combustion characteristics of flames in furnaces including industrial furnaces, analyze and evaluate flame control parameters, and study low-pollution combustion technologies. Experimental methods acquired by 1997 were used for the experiments under the microgravity environment. Evaluation experiments were performed on flame shape control technologies and flame radiation characteristics, and basic experiments on the low-pollution combustion technologies. With these experiments, elucidation of the combustion mechanisms was launched by analyzing and evaluating the acquired data. A flame experimenting device for high-temperature preheated air completed by fiscal 1997 was used to acquire such combustion characteristics data as NOx discharge characteristics when the high-temperature preheated air is used. Based on the result thereof, verification was carried out on simulation models. (NEDO)

  4. Comprehensive report on researches of the Institute of Energy Economics (1985-1995); Nihon Energy Keizai Kenkyusho kenkyu hokoku soran 1985-1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-31

    This is a comprehensive report on researches made during 1986-1995 by the Institute of Energy Economics. The institute had the 30th anniversary of the founding in 1996, and the world economical and energy situation was greatly excited during the period by such as two oil shocks, the Gulf War, collapse of the former U.S.S.R. Notice is taken of the global environmental problem, the increase in energy demand in Asia, the increasing dependence on the Middle East, etc. Under these conditions, the report includes the following by content: 16 items in general energy, 11 in energy policy, 12 in energy utilization/energy conservation relation, 38 in energy supply/demand, and 13 in international cooperation relation. Moreover, the report includes the following by energy: 33 in petroleum, 5 in coal, 15 in electric power, 2 in nuclear power, 8 in gases like LNG and LPG, and 8 in new energy. In addition, there are 17 papers on economy/industry relation and 23 on environmental problems. As viewed by region, the report has 13 papers in the U.S., 19 in Europe, 6 in oil producing countries/OPEC, 6 in Russia/former U.S.S.R., and 20 in Asia.

  5. R and D of remote reading system. Remote reading system no kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakano, H.; Hamada, T.; Nakamura, O. (The Kansai Electric Power Co. Inc., Osaka (Japan)); Imai, Y.; Akiyama, K.

    1992-03-25

    As measures for the spots difficult in metering within a framework to integrally automate the power distribution, a remote reading system was prototypically tested and evaluated in reliability on the actual field. The system methodically selected the signal {prime}s line injection, high frequency wave signal and voltage detection, while the signal frequency, transmission rate and highest transmission output were set at approx. 3.5KHz, 7.5bps and 50dBm, respectively from the test result. The demonstration test on reliability of the system locatively selected a vicinity of high voltage consumer, high harmonic wave-generating consumer, transforming station, etc. The total ratio of success in reception was comparatively high in Kuzuno and Yamazaki areas, but low in Kamojyo and Ichinomiya areas, The badness in reception was caused by the fluctuation in noise and strongness in damping which was influenced by the condenser in the high voltage consumer. The locative relation between the parent and child stations of system, and high voltage consumer being classified into four patters, an application table of remote reading system was prepared by simulation. 14 figs., 6 tabs.

  6. Jet engine R and D and I; Watashi to jet engine kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Murashima, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1998-06-10

    My efforts towards at the development of aeroengines since the end of the war are described. The J3-7 engine propelled the T1 trainer plane, and was installed as booster aboard the P2J antisubmarine patrol aircraft. It was the first jet engine that Japan produced after the end of the war, and had been in use until quite recently. I took part in the construction of a prototype of the JR100 series designed to serve as VTOL (vertical take-off and landing) aircraft lift engines, and in the test thereof. As the shift from turbojet to turbofan proceeded, I participated in the development of the FJR710 engine under the guidance of National Aerospace Laboratory, and the product was installed aboard an experimental STOL (short take-off and landing) aircraft Asuka. I next joined a Defense Agency initiative for a reheat turbofan to replace the J3 aboard trainer plane, and the result was the low bypass ratio/high output F3 engine. In 1989, Ministry of International Trade and Industry decided for a large-scale project of developing an engine for a next-generation supersonic transport, and the HYPR (Super/Hypersonic Transport Propulsion System) project was started. The project was participated in by manufacturers from overseas, which were GE, P and W, RR, and SNECMA. The foreign corporations worked on an equal footing with the Japanese parties, and collaboration between the participants was smooth, with each party endeavoring in the field they were good at. The project will be concluded as scheduled in fiscal 1998. (NEDO)

  7. Demonstration of energy-saving construction works; Shoshigenka wo mezashita kenchiku koji no jissho kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, T.; Yamagishi, M.; Kakimi, S. [Chubu Electric Power Co. Inc., Nagoya (Japan)

    1997-11-01

    Studies are conducted to promote energy-saving in construction works as part of environment protection programs. The first phase is for survey and analysis works for energy-saving in the current building design and construction works, and for processes, procedures and materials in model works (construction of sub-stations). The second phase is for studying energy-saving designs, materials and procedures, which are applied to model works, to assess their energy-saving effects , costs and applicability. The horizontally developed samples are prepared for the future development, based on the `continuous improvement of environment-management systems by establishing the PDCA cycles,` which is one of the basic requirements of the ISO14001 (environment management system). These efforts have reduced CO2 emissions associated with the manufacture of construction materials by 20%, mixed wastes by 45%, and plywood frame requirement by 70%. It is also confirmed that they can be realized at only around 3% higher cost. 9 refs., 10 figs., 3 tabs.

  8. Achievement report for fiscal 1998. Leading research and development of MGC-built superhigh-efficiency turbine system technology; 1998 nendo MGC chokokoritsu turbine system gijutsu sendo kenkyu kaihatsu kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To further enhance energy efficiency by improving on the gas turbine system, it is necessary, first of all, to develop superhigh-temperature materials to allow the system to operate at higher temperatures. Described in this report are studies on the application of MGC (melt-growth composite) materials which retain strength and plastic deformation capability even at high temperatures. Various compositions are explored for improvement on fracture toughness and thermal shock resistance. The Al{sub 2}O{sub 3}/YAG system is investigated for the study of relations between microstructural control and fracture toughness. Literature on the development of nanocomposites is surveyed, and a preliminary experiment is discussed for improvement on purity by zone melting crystallization. In a study for an advanced manufacture of larger crystals, technologies of crystal growth condition setting and optimization, quality stabilization, productivity improvement, and crystal size enlargement are taken up. Casting and machining technologies are studied to enable crystals to assume complicated shapes. For the purpose of elucidating the mechanism of the occurrence of properties proper to high temperatures, a study is made on the evaluation of mechanical and physical properties and on the mechanism and control of crystal growth. Also studied are systems (gas turbine cycle, combustor, etc.) to which MGC materials may be applied. (NEDO)

  9. Fiscal 1997 report on technological results. R and D on micromachine technology (Development of micro-factory technology); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Activities are conducted in search of a micromachine system in which devices and equipment relating to machining, assembly, transportation, inspection, etc., in use for a manufacturing process are integrated in a narrow space, for the purpose of conserving energy through the miniaturization of the process of manufacturing small industrial products. With the activities in the two fields of (1) R and D of systematization technology (experimental system for micro fabrication/assembly) and (2) comprehensive investigation and research, examination on detailed specification for the experimental system was carried out, as were the examination of element technologies, element device operating experiments, technological investigation, etc.. In (1), sophistication of the element technologies was contrived that were required for realizing each experimental system, while the detailed specification of each experimental system was decided. Further, a part of the element devices was experimentally manufactured, with the basic functions verified. In (2), research studies were compiled on radio interference for example in the case where various devices were integrated and highly densified through the formation of a micro-factory; also compiled was a joint research with Agency of Industrial Science and Technology, a research conducted for the purpose of building the conception of the micro-factory. (NEDO)

  10. Fiscal 1999 achievement report on research and development of industrial technologies. Research and development of synergy ceramics; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are conducted in the two fields of (1) survey and research and (2) development of technology for evaluating high temperature dynamic corrosion characteristics of heat resistant ceramics. In field (1), a comprehensive survey is conducted, an application study is conducted about high temperature gas separating ceramic membranes, and efforts are made to put to practical use ceramic parts manufactured by a low cost production process. In the application study of ceramic membranes, technologies are developed for a process of manufacturing high temperature gas separating porous ceramic membranes capable of separating and purifying gas emissions and gas ingredients, which involves the development of technologies for improving on gas separation and purification functions, development of technology of providing catalyst support function, technology of porous membrane formation, evaluation of separation characteristics, and so forth. In an application study for ceramic parts manufactured by a low cost manufacturing process, which involves structural ceramics, optimization is accomplished for materials synthesizing technologies by means of mechanical alloying, and cylinder liners are fabricated and evaluated for a natural gas engine made of silicon nitride based ceramics. In field (2), a high temperature dynamic corrosion testing device is built for heat shield coatings. (NEDO)

  11. Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

  12. Present developmental conditions of petroleum substituting energies in the U.S.A; Sekiyu daitai energy no kaihatsu no genjo (Beikoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The present developmental conditions of petroleum substituting energies in the U.S.A. were surveyed. The budget related to energy saving and petroleum substituting energies in the U.S.A. is on the increase. DOE`s expenditure on petroleum substituting energies increased from $6.8 billion in 1993 to $8.1 billion in 1995 (from 29.6% to 34.6% of DOE`s expenditure), showing the positive approach to development of petroleum substituting energies. Approaches to environmental protection are also in promotion such as positive use of electrical vehicles by U.S. government and emission regulation of specific pollutants by EPA. The state of California withdrew the regulation which prescribes that 2% of passenger cars sold in the state should be zero emission vehicles after 1998, because development of the battery with both sufficient mileage and output is impossible by 1998 in the present stage. The prospect of practical use of new batteries such as lithium battery is still far from certain for some years. Development of petroleum substituting energies in the U.S.A. is still insufficient. 17 refs., 1 fig., 4 tabs.

  13. Load leveling air conditioning technology development by unused energy high-level utilization. Summary of achievements by development themes; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu kaihatsu. Kaihatsu temabetsu seika gaiyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-01-01

    This paper introduces a number of research and development cases on utilization of unutilized energies. In developing the component technology for a thermal plant utilizing low-temperature unutilized energies, the paper introduces a heat exchanger system to collect heat from sea water, a heat exchanger system to collect heat from waste heated area in subways and urban sewage plants, and a high-density heat transportation system using ice plus water slurry or PCM-C plus water slurry. Furthermore, with regard to the heat pump system using low-temperature unutilized hear sources, development was introduced on a 'heat source load responsive heat pump system', which combines a load variation responsive heat pump utilizing river waters with a latent heat storage system using nighttime electric power serving for electric power load leveling. In developing the component technology for a heat plant utilizing high-temperature unutilized energies, introduction was given on a turbine driven turbo type heat pump system, a high-efficiency absorption type heat pump, a waste heat driven absorption type freezer, and an urban type underground heat storage tank. (NEDO)

  14. Evaluation report on the R and D of the membrane separation process introduction technology; Makubunri process donyu gijutsu no kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper reported the R and D of the membrane separation process introduction technology during a period of 1994 through 1998. The membrane separation technology is not associated with the phase change which requires large energy and expected to be an energy saving process. For the production of membranes required of high functions, the vapor deposition polymerization method was considered, and high order structure control of the membrane, control of adhesion and attachment, and control of orientation, and development of the high polymerization technology were required. For the high grade control of vapor polymerization, the substrate surface structure/quality were important. The molecular level analysis of the vapor deposition surface was also needed. Therefore, the paper took notice of STM (scanning tunneling microscopy), AFM (atomic force microscopy) and HREELS (high resolution electron energy loss spectroscopy) as surface atomic/molecular configuration analysis technology, and designed/fabricated and studied the high resolving power and high sensitivity analysis equipment using the analysis equipment which combined HREELS and STM and the analysis equipment using SFG (sum frequency generation) which can detect signals in the low frequency region. Making full use of the highest technology, technology was able to be developed for substrate surface analysis and surface reaction analysis technologies which become the basis of the high performance separation membrane fabrication technology by the vapor deposition polymerization method indispensable for introduction of the membrane separation process. The technology can be the base applicable to a lot of fields where surfaces and interfaces are concerned

  15. Fiscal 1974 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on the system for apartment houses); 1974 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Shugo jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-01

    This report describes the fiscal 1974 R and D result on solar cooling/heating and hot water supply systems for apartment houses. In system analysis, the system plan was selected through basic data survey, modeling by combining some kinds of such systems and energy flow calculation. On solar heat collector, theoretical analysis was made on a stationary plane collector, and study was made on cover glass material and absorption surface performances. On Rankine's engine, studies on advanced selective absorption film, transmissive film, prevention of heat radiation and converging collector were necessary. As solar heat driving refrigerators, absorptive one and Rankine's one were promising. As heat media for refrigerators, R-11 and 113, and R-114 and 11 were suitable for turbo one and displacement one, respectively. Since a displacement compressor is featured by high-efficiency lower-speed operation than that of turbo one without any constraint, its direct connection with a motor or generator is possible. Screw compressor belonging to displacement one was promising. Rotary displacement one was also promising in a small-capacity range within 20-50RT. (NEDO)

  16. Present situation of the development of petroleum substitution energy (E.U.); Sekiyu daitai energy kaihatsu no genjo (EU)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper investigates and reports policies for and the developmental trend of petroleum substitution energy in the E.U. The technology of 18 wind turbine makers in West Europe is on a level that they can almost sell MW-class turbines for practical use. The wind turbine industry in Denmark is on a level of No.1 of the world, and occupies approximately 50% of the world market share. The capacity of the wind power generation in Germany which finished the installation at the end of 1995 exceeded 1000 MW. EEWC has recently been established as an organization for using waste as energy. Municipal solid wastes discharged in West Europe are regarded to be equivalent to 5% of all the power demand there. In Spain, biomass is a petroleum substitution energy source which is most used. A target amount for the use set by the government is equal to 427000 tons in oil. Biomass is most used in the residential field, and it is mainly the use of agricultural and forestry wastes as fuel. Rapeseed oil is studied as fuel for bio car. In Denmark, production of rapeseed as fuel use crop is increasing. 14 refs.

  17. Achievement report on developing superconductor power applied technologies in fiscal 1999 (2). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power generators. This paper summarizes the achievements thereof in fiscal 1999. A verification test was given on the rotor of an ultra high speed responding generator. In a sudden short circuit test using the different phase charging method, no anomalies were found such as quench generation and vibration changes, wherein the healthiness of the generator was verified. In the VVVF actuation test, knowledge was acquired on the actuation method when the ultra high speed responding generator is applied to a combined cycle plant. After the verification test has been completed, the disassembly inspections such as visual check and non-destructive test were performed. With regard to the vacuum leakage found in the rotor under very low temperatures, the causes were presumed and the countermeasures were discussed by observing the weld structures. In the design research, the conception design on the 200-MW pilot generator was reviewed by reflecting the results of the verification tests on the model generator. At the same time, trial design was made on a 600-MW target generator. In summarizing the overall research achievements, the achievements and evaluations were summarized on technological issues that have been allotted to each research member. (NEDO)

  18. Achievement report for fiscal 1998 on the development of superconductor power application technology. 2. Research and development of superconducting wire and superconductive power generator, research of total system, research and development of refrigeration system, and verification test; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total sytsem no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The slow excitation response type power generator is studied when the rotor and stator of a 70,000kW-class model are combinedly subjected to an on-site verification test, when a good result is obtained. The rotor is disassembled for inspection, and its members are found to be sound without any problem in terms of mechanical strength. The quick excitation response type is studied when a 70,000kW model is experimentally built and subjected to an on-site verification test after a rotation and excitation test in the factory, when the pilot machine concept design is reviewed. In the study of a total system, efforts continue for the review of the model machine test method, improvement on generator design and analytical methods, development of operating methods, and the effect of its introduction into the power system. Since a He-refrigerated system is requested to exhibit high reliability for application to power equipment and to be capable of continuous long-period operation, a system having constituents with their reliability enhanced and an appropriate redundant system is developed, and a verification study is under way which will continue for more than 10,000 hours. Described also is an oil-free low-temperature turbo refrigerator. The latest quick excitation response type rotor is also tested for verification. (NEDO)

  19. Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    This report refers, continuously to the Part 1, to the in-situ verification test of the slow-response type model machine rotor and to the review of the conceptual design of the pilot machine. On the basis of the R and D results of various element technology/partial models obtained before the previous fiscal year, the design, manufacturing and factory test had been conducted for a 70,000kW class slow-response type model machine rotor. This year, an in-situ verification test was performed to complete the test of all planned test items. Using the technological results obtained in the design, manufacturing and test of the 70,000kW class model machine, the conceptual design is being reviewed of the 200,000kW class pilot machine. In the aspect of the functional design, accurate grasping of the thermal load is essential for the purpose of attaining a large capacity for a superconducting generator, as a part of which a thermal load analytical method was planned to be established for a torque tube heat exchanger. The reasonableness of the analysis was verified through a comparison with the factory test result of the 70,000kW class slow-response type rotor, indicating good agreement between the calculation result and the actual measurement, and enabling the result to be obtained that explains dependency of the thermal load on the number of revolution. (NEDO)

  20. Achievement report on developing superconductor power applied technologies in fiscal 1999 (1). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power applied technologies. This paper summarizes the achievements thereof in fiscal 1999. In research and development of the superconductor wire materials, decrease in loss and increase in capacity of the conductors were progressed for the Nb{sub 3}Sn wire material, whereas its mechanical properties and stability were evaluated. In research and development of the superconductor generators, an ultra high speed responding generator was verified of its healthiness in a sudden short circuit test. A linkage test with an operating 77-kV system was performed, wherein verification was given that the superconductor generator can be operated stably against various disturbances. In research and development of the freezing systems, an improved system was structured, which achieved operation of 11,390 hours in a single system as a result of the high reliability of the oil-free structure. In the verification tests, the ultra high speed responding model generator was connect to the freezing system to give such tests as load test, onerous test, actuation test by using the M-G system, and 77-kV system linkage test. The functions, reliability, and durability of the system were verified, and different data were acquired. (NEDO)

  1. FY 1998 annual report on the preliminary research and development of techniques for developing resources from gas-hydrate. Studies on gas-hydrate exploration, excavation techniques, methods for assessing environmental impacts, and gas hydrate handling systems; 1998 nendo gas hydrate shigenka gijutsu sendoken kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no kenkyu kaihatsu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This R and D project is for the preliminary studies on development of the following 4 types of techniques for developing resources from gas-hydrates (GH): (1) gas-hydrate exploration, (2) excavation techniques, (3) methods for assessing environmental impacts, and (4) gas hydrate handling systems. The FY 1988 R and D results are described. For gas-hydrate exploration, the methods for analyzing inorganic ions and trace quantities of elements, which are necessary for accurately estimating the offshore GH around Japan, are established; and case studies are conducted for methods of predicting GH deposit forming mechanisms, and stability fields of GH, based on terrestrial heat flow and seismic data. For excavation techniques, GH decomposition rate is analyzed using a laboratory system which reproduces conditions of excavation of GH layers. For methods for assessing environmental impacts, a geo-hazard predicting model is established, to study ground displacement and gas leakage sensing systems and data transmission systems to cope with the hazards. For gas hydrate handling systems, an overall system is studied, and storage and transportation systems are outlined. (NEDO)

  2. Report on the FY 1999 results of the development of the wide area energy utilization network system - Eco/energy urban system. 2/2. Study of the systematization technology/evaluation technology out of the study of the energy system design technology (Study of the application method of element technology/system and trial calculation of the introduction effect); Koiki energy riyo network system kaihatsu (eco energy toshi system). 2/2. Energy system sekkei gijutsu no kenkyu no uchi system ka gijutsu hyoka gijutsu no kenkyu 1999 nendo seika hokokusho (zenkoku no netsu juyo no bunpu jokyo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of smoothly introducing the equipment technology and system technology being studied in the development of element technology in the eco/energy urban project, the paper conducted the study of conditions/application method in applying the technology to the actual energy supply system, analysis of the introduction effect, arrangement of the subjects on technical development, etc. In the study, for the methanol/hydrogen base technology, heat pump technology, heat recovery technology, heat transport technology and heat power generation technology, the quantitative analysis was made in terms of the lifecycle energy consumption amount, lifecycle CO2 emission amount and lifecycle expenses. As to the methanol base system, the subject is the reduction in auxiliary power. Concerning the heat pump technology, the subject is the enlargement of simple equipment. As regards the heat recovery technology, the subject is the development of system with long useful year. Relating to the heat transport technology, subjects are the completion of the menu of large-diameter piping in the vacuum thermal insulation heat transport piping system, and reduction in conveyance power of heat medium. About the heat power generation technology, subjects are the stability/durability of the system. (NEDO).

  3. Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Research and development of energy conservation oriented collective detoxification system for dioxins and toxic heavy metals in fly ash and soil; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Hibai dojochu no dioxin rui yugai jukinzoku no sho energy gata ikkatsu mugaika shori system ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop a system to collectively detoxify dioxins and heavy metals in incinerator fly ash or in polluted soil using microbes and/or chemicals. In the use of chemicals, verification tests are conducted for a system to detoxify dioxins and toxic heavy metals simultaneously. In the use of microbes, an effort is made to develop a low cost energy conservation type treatment system based on what is provided by the study of microbes such as Phanerochaete chrysosporium. As for the treatment of fly ash, an effort is made to recycle it into resources usable in the development of marketable products. For the detoxification of dioxins using chemicals, they are dechlorinated in a chemical reduction reaction. For their detoxification with help of microbes, it is found in an experiment of ash fly dioxin decomposition using Phanerochaete chrysosporium that the microbe reduces dioxins in both liquid phase and solid phase systems. The result of verification tests using chemicals shows that the reference level of 3ng-TEQ/g is easily cleared in the treatment of high concentration ash fly. In the detoxification of heavy metals, data is obtained indicating that the elution level of lead in ash fly is found reduced by 70-85% after treatment. (NEDO)

  4. Survey report on the development/utilization of petroleum substitution energy in the Pacific region; Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper collected/analyzed data on petroleum substitution energy in the Pacific region. In fiscal 1996, in addition to collection of the existing energy data, conducted were collection of energy data made retroactive from 1971, and time-series collection of the energy related expanded data including energy related production statistics/social statistics, energy consumption amount by industry, power generation facilities, oil production facilities, and environmental data. As to petroleum substitution energy, the paper took up new energy such as hydroelectric, nuclear, geothermal, photovoltaic, and wind power generation, and commercial-base renewable energy. As a result of the analysis, the supply of petroleum substitution energy in the whole Pacific region has been stable, 6.6% during 1980-1990, 7.4% in the first half of the 1990s, largely over the primary energy supply. The supply of nuclear power was overwhelmingly large, followed by hydroelectric energy and geothermal/new energy. 15 figs., 23 tabs.

  5. International research cooperation project. Assessment report on the R and D of the comprehensive development/utilization technology of energy of gas hydrate resource; Gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As to 'the R and D of the comprehensive development/utilization technology of gas hydrate resource,' assessment was conducted and reported from an aspect of the third party. This R and D is a timely project being aimed at establishing the basic technology on gas hydrate from both aspects of fundamental research and practical research. In the development of gas hydrate resource in the tundra zone, the development of measuring methods for thermal conductivity and dielectric constants advanced the establishment of a guide for exploration and possibilities of assessment of the resource amount. In the development/production, it can be said that the knowledge/information collected by exchanging methane in gas hydrate with CO2 means no needs for new supply of heat and also contributes to the isolation of CO2. As to the utilization technology, the results were rated very high also internationally of tackling the quantitative evaluation method at molecular levels of the gas included in hydrate using Raman spectroscopy to establish the industrial gas separation method using the low-temperature environment in the tundra zone. (NEDO)

  6. Data book on new energy technology development in FY 1997. Cogeneration; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Various policies are being implemented in the field of new energy technology in line with progress in technological development. Examples are about assistance mechanism, field test projects and advisory projects to support the introduction of new energy technology. In order to promote the introduction of new energy efficiently, it is necessary to compile the various information regarding new energy in a comprehensive and systematic way, and formulate a basic data set. Among various new energy technologies, cogeneration is discussed in this report. The latest published data on the respective technologies are compiled particularly regarding their overall systems, examples of introduction, assistance mechanisms and state of implementation in foreign countries. Items included in this report are the trend of cogeneration, outline of system, state of introduction, forecast of introduction, overview of policies, basic terms, and related organizations. 9 figs.

  7. Feasibility study of international cooperation in the research/development of a solar energy utilization system by the innovative solar thermochemical process; Kakushinteki solar netsukagaku process ni yoru taiyo energy riyo system no kaihatsu kenkyu ni kakawaru kokusai kyoryoku kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    At COP3 in 1997, an agreement was made to the innovative technical development/promotion by international cooperation, and the promotion of transfer of environmental technology to developing countries. Under the agreement, a feasibility study of international cooperation was made, and especially a study was conducted of the utilization/development of solar energy by the innovative solar thermochemical process. The main reason for global warming is emissions of a large amount of CO2 caused by the direct combustion of fossil fuels. Therefore, a CO2 recycle system taken up in the study enables a more substantial decline in CO2 emission (kg/kWh) per unit generation than the conventional thermal power system by composing solar methanol or solar dimethyl ether using fossil fuels including coal, water, CO2, etc. as raw materials and using solar energy as heat source, and by using this as fuel (solar fuel). CO2 can be reduced by 13% to 14% by substituting solar methanol or solar dimethyl ether produced from petroleum/methane equivalent-mol mixed raw materials for the equivalent mol coal and natural gas of the thermal power plant (CO2 recovery is not necessary). 34 refs., 47 figs., 34 tabs.

  8. Survey on construction of the database for new energy technology development. Cogeneration; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the activity promoting use of new energy, the data related to cogeneration were systematically compiled. For new energy technology, such various policies for introducing new energy are in promotion with a progress of technological development as preparation of subsidy systems, field test business, and support advisory business for introducing new energy. For further effective promotion, integral systematic compilation of various data, and arrangement as basic data are necessary. Such latest announced data in a cogeneration field were collected and compiled as outline of new energy systems, concrete applications, subsidy systems, and approaches to new energy of various countries. Main data items are as follows: trend of cogeneration, outline of system, domestic and foreign concrete applications, prediction data on the use of new energy, overview of domestic and foreign policies for cogeneration, basic terminology, and tables of main related enterprises and organizations. This database is useful for the present activities promoting use of new energy, and preparation of the future vision. 29 figs., 33 tabs.

  9. Achievement report on research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a recombinant DNA utilizing technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Achievements were compiled on the research in fiscal 1981 on the 'research and development of a recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. For the method to create energy saving type bacteria stocks for processes centering around the escherichia coli, refinement was carried out on cytochrome P-450 and NADPH-cytochrome P-450 reduction enzyme respectively from hepatic microsome of rats administered with induction agents. Attempts were made to prepare antibodies working on them. For the method to create high-efficiency secreting bacteria stocks centering around bacillus subtilis, activity measurement and quantification were performed on enzymes external to the bacillus sutilis, and research was executed on introduction of neutral protease gene sensitive to bacillus subtilis temperatures into the NA20-S17 stock. For the method to create bacteria stocks to substitute raw materials used in the chemical industry, studies were performed on separation of enzymes and corresponding genes, and incorporation of the genes into the escherichia coli. In the comprehensive investigation and research on the recombinant DNA utilizing technology, information exchange and discussions meetings were held, and investigations were made on literatures and patents. (NEDO)

  10. Achievement report on research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a recombinant DNA utilizing technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Achievements were compiled on the research in fiscal 1981 on the 'research and development of a recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. For the method to create energy saving type bacteria stocks for processes centering around the escherichia coli, refinement was carried out on cytochrome P-450 and NADPH-cytochrome P-450 reduction enzyme respectively from hepatic microsome of rats administered with induction agents. Attempts were made to prepare antibodies working on them. For the method to create high-efficiency secreting bacteria stocks centering around bacillus subtilis, activity measurement and quantification were performed on enzymes external to the bacillus sutilis, and research was executed on introduction of neutral protease gene sensitive to bacillus subtilis temperatures into the NA20-S17 stock. For the method to create bacteria stocks to substitute raw materials used in the chemical industry, studies were performed on separation of enzymes and corresponding genes, and incorporation of the genes into the escherichia coli. In the comprehensive investigation and research on the recombinant DNA utilizing technology, information exchange and discussions meetings were held, and investigations were made on literatures and patents. (NEDO)

  11. Fiscal 1997 report on the results of the international standardization R and D. R and D of the basic evaluation method of functional composite particles; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Kinosei fukugo biryushi no kibanteki hyoka hoho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper established the basic evaluation method of composite particles manifesting functions which the existing mono-componet particles do not have and aimed at the international standardization of the measuring method of them. To be concrete, the development was studied of methods to evaluate the mechanical bonding state of different composition in composite particles, the chemical bonding state of different composition and the electromagnetic state of the surface of composite particles. As a result, in the evaluation method of the mechanical bonding state of different composition in composite particles, methods to evaluate the bonding state and the large composite bonding state of the coated particle layer were developed to clarify the details to be standardized for each method. In the evaluation method of the chemical bonding state of different composition in composite particles, the electronic energy loss spectroscopy was an effective method to evaluate the chemical bonding state in composite particles of oxide ceramics. Further, in the evaluation method of the electromagnetic field of the surface of composite particles, standard experimental procedures for observing the electromagnetic field by interference of electronic waves were proposed, and the evaluation of the electromagnetic field state of composite particles used ranging from low temperature to high temperature was made possible. 41 refs., 85 figs., 14 tabs.

  12. `Joint Research and Development of Industrial Technology,` an international research collaboration for fiscal 1997. Research and development for practical application of low-temperature sinterable, highly heat-radiating materials for ceramics; 1997 nendo kokusai kenkyu kyoryoku jigyo `sangyo kiban gijutsu kyodo kenkyu kaihatsu`. Teion shoketsu kohonetsusei ceramics kiban zairyo no jitsuyoka gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A highly heat-conducting AlN ceramic substrate is developed for the cooling of semiconductor integrated circuit devices and power controlling semiconductor devices. In the development of a low-temperature sinterable ceramic texture, a sintering assistant is selected. In this process various assistants are tested for the effect of their presence on the occurrence of AlN oxidation and on the magnitude of standard energy for aluminate compound formation. The volatility at high temperatures of the components of the assistants are also examined. The sintering assistant developed for this project (mixture of Y2O3, CaO, LaB6, and WO3) is used in the sintering of an AlN material powder developed by The Dow Chemical Co., and then it is demonstrated that highly heat-conducting AlN substrates are mass-produced by continuous sintering at 1600degC in a nitrogen atmosphere, the product having a relative density of 100%, average heat conductivity of 154W/mK, bend resisting strength of 440MPa, and a fracture toughness value of 3.8MPam{sup 1/2}. 6 refs., 92 figs., 10 tabs.

  13. Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

  14. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of new software structuring models (R and D of micromachine cooperative control use software); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Shin software kozoka model no kenkyu kaihatsu (bisho kikai kyocho seigyoyo software no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted of software structuring models which ease the development and maintenance of software systems and meet diversification of needs. As for the study of the cooperative control use programming language, a R and D of agent oriented language Flage was carried out for expansion of language function, arrangement of network function, development of exercises, etc. As to the formulation of agent knowledge, proposed were processes to make a program from the specifications, and EVA, a mechanism in response to changes in the specifications of existing programs. In relation to the basic theory of cooperation system, a study was made mainly of object oriented attribute grammar OOAG as a model representing cooperative computation in software process as a rule group. Concerning the study of the situation recognition mechanism, researched were models of communication and reasoning among agents in cooperation. 187 refs., 107 figs., 23 tabs.

  15. Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

  16. Data book on new energy technology in FY 1997. Wind power generation; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Furyoku hatsuden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is an urgent necessity for Japan to promote the technological development and accelerate the introduction and diffusion of new energy. In order to diffuse and enlighten the introduction of new energy technology efficiently, it is necessary to compile various information regarding new energy in a comprehensive and systematic way, and formulate a database. Aiming at the systematic formulation of data on new energy, this survey focuses on the field of wind power generation system (WPS) and provides a collection of the latest published data on WPS, particularly regarding the worldwide installed wind power capacity, support plan and government policies, current situations of WPS market, and major technical characteristics of typical wind turbines. This report consists of the significance of wind energy, world market of wind turbines, government policies, international wind energy development, subsidies for wind energy, procedures of wind turbine system installation, governmental measures for wind energy development, subsidiary companies and organizations, basis of wind energy, and Japan`s wind energy development in 1997

  17. New energy technology development related database construction survey (wind power generation); Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (furyoku hatsuden)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To arrange systematic data relating to new energy, the latest published data relating to the wind energy conversion systems have been collected and arranged. For the overview of wind energy conversion system, wind turbines with horizontal axis and vertical axis, specification of wind turbine, and conceptual figure of wind energy conversion systems are illustrated. For the installation examples, introduction development of wind energy conversion systems in the world is described for Japan, the USA, Germany, Denmark, Spain, Sweden, India, and Belgium. For the relevant legislation and support plan, relevant legislation for the introduction of wind energy conversion in Japan, support plan in Japan, and support plans in foreign countries are described. Prices of wind turbines by wind turbine makers in the world, construction cost by Japanese makers, basic term, and subsidiary company and organization are shown

  18. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Development of new vacuum ultraviolet area optical materials realizing next generation short wavelength optical lithography; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Jisedai tanhacho hikari lithography wo jitsugensuru shinku shigaiiki kogaku zairyo no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As materials for next generation lithography use optical device using short wavelength light sources such as F{sub 2} and Ar{sub 2}, the development was proceeded with of fluoride monocrystal materials and 12-inch class large/high quality monocrystal production technology. Studies were made in the following five fields: 1) proposal/design of new materials and the heightening of performance: 2) establishment of the large/high quality crystal production method; 3) evaluation of optical properties and elucidation of micro-defect formation mechanism; 4) comprehensive investigational research; 5) study of the evaluation technology by vacuum ultraviolet area pulse light. In 1), for the development of the optimum materials, a lot of materials were tried to be monocrystallized, and the permeability was estimated by measuring the reflectance in the vacuum ultraviolet area. As to LiCaAlF{sub 6}, monocrystal with 1-inch diameter was made by the Bridgman method. In 2), studies were made of conditions for large crystal growth by the pull method, large crystal growth by the Bridgman method, and the structure of production equipment for crystals with larger diameter. (NEDO)

  19. Achievement report for fiscal 1989. Research and development of ceramic gas turbine (Study on its adaptability with society); 1989 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Shakai tekigosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-05-01

    Ceramic gas turbine (CGT) is superior in the aspects of high efficiency, low pollution, multi-kind fuel performance, small size, and light weight. Its utilization field is broad, whereas putting it into practical use at an early time is desired from the viewpoints of energy conservation, reduction in CO2 emission, resource conservation, and economic influence. The utilization field of CGT may include cogeneration and portable power generator, but putting it into practical use requires that it be superior in environment protection performance such as gas exhaust, noise and vibration, economic performance, safety, and adaptability with the utilization fields. From such a viewpoint, discussions were given on its adaptability with the society based on different characteristics of the CGT, and other conditions such as related laws and regulations. The first edition investigated the developmental trends in ceramic materials, and the second edition studied the CGT utilizing systems, in particular, the status of utilization and proliferation of the current cogeneration systems. The edition evaluated various conditions required for conceptual design of the system. The third edition put into order the environmental regulations and future trends in order to identify the effect of introducing the CGT. (NEDO)

  20. Development of a new electric battery electric power storage system. Results of the 12-year R and D; Shingata denchi denryoku chozo system kaihatsu. 12 nenkan no kenkyu kaihatsu no seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    The paper described the results of the R and D which have been continued for 12 years on a new electric battery electric power storage system (load leveling function). The electric batteries for study were Na-S, Zn-Cl, Zn-Br, and redox type. Charge/discharge operation of 211 times was conducted of a pilot plant with a Na-S battery 1,000kW and 8-hour capacity. The overall efficiency of system was 71.5-76.0%, and the energy efficiency of battery was 86%. As a whole, the performance was able to be confirmed which can fulfil a developmental target. The system overall efficiency of 65.9% and battery efficiency of 76.1% were obtained. The experiment on battery life was carried out at plant together with the pilot operation. The mean life of Na-S battery was estimated at 800 cycles, and that of Zn-Br battery at 500-800 cycles. The effectiveness of the new electric battery electric power storage system was technically verified. For the future commercialization, studies on the following are needed: enhancement of reliability, easiness in maintenance/inspection, size reduction, cost reduction, etc. (NEDO)

  1. Advanced research and development of gas hydrate resources. R and D of exploration and others - R and D of excavation technologies and others - surveys/researches on methods of evaluating environmental effects - surveys/researches on application systems; Gas hydrate shigenka gijutsu sendo kenkyu kaihatsu. Tansa nado ni kansuru kenkyu kaihatsu / kussaku gijutsu nado ni kansuru kenkyu kaihatsu / kankyo eikyo hyokaho no chosa kenkyu / riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Gas hydrate is a clathrate compound in a gaseous molecule as the host, stable under relatively mild environments. It is deposited in the 600m or deeper sea bottoms to form the gas hydrate deposit and massively occurring in the sea areas around Japan. This deposit has been studied viewed from natural gas resources, causes for natural hazards and contribution to the global warming. This project excavates a well in the deposit, to study possibilities of the technologies for decomposing, fluidizing and lifting the hydrate as the gas source, and for establishing the natural gas transporting/mooring systems in which its characteristics are utilized. The R and D activities are directed to the 4 areas, (1) development of the exploration technologies to determine the deposit sea area, quantity and conditions, (2) development of the stable well-excavation technologies, (3) studies on the effects of gas production on the environments, and development of the system for predicting the effects, (4) and studies on the application systems. The item (3) finds out the transportation/storage system possibly more economical than the current freezing/liquefaction technologies. The item (3) has the development themes of evaluating the geohazards caused by excavation and gas production, and their effects on the ecological systems. (NEDO)

  2. Fiscal 1974 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on the system for existing detached houses); 1974 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Kison kojin jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-28

    This report describes the fiscal 1974 research result on solar cooling/heating and hot water supply systems for existing detached houses. The program for calculating heat collection rates was prepared by integrating peripheral conditions and every calculation step of heat collection rate, mean value, accumulated value and changes caused by disturbance. The cooling/heating load calculation program was also prepared for unsteady dynamic thermal analysis of houses. Another program was prepared for hot water supply load because of a large difference in life pattern. The profitability and energy conservation of 644 systems different in heat source, heat discharge, heat collection, heat storage, auxiliary heat source and equipment were evaluated by heat balance calculation program. Survey and study were also made on various heat engines such as heat pump, absorption refrigerator and Rankine cycle engine. Based on the survey result on existing technology for plane collectors, the optimum design method of collectors were established through various characteristic tests. Some kinds of suitable fusion latent heat type heat media were selected, and their operation stabilities were studied. (NEDO)

  3. Fiscal 1976 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on the system for new detached houses); 1976 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. shinchiku kojin jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    R and D was made on solar systems for new detached houses, and design and construction of the experimental house were carried out. In system analysis, assessment of solar cooling/heating systems, improvement of a simulation model based on measured data, and improvement of cooling/heating systems by simulation were conducted. In development of equipment and materials for the experimental house, R and D was made on component materials, connection method and installation method on houses for vacuum glass tube type solar collectors, and a solar collector was fabricated. R and D was also made on combination of absorbent and coolant, drop type coolant generator and performance experiment for absorption refrigerators, and a refrigerator was fabricated. The experimental house is 2-stored RC wall construction of 79.94m{sup 2} in building area, and 133.26m{sup 2} in total floor area. From the viewpoint of energy saving, outside insulation, double window, and insulating rain shutter door were adopted. The newly developed vacuum glass tube type solar collector is applicable to existing houses because of its higher flexibility. (NEDO)

  4. Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. R and D of high-performance industrial furnaces, etc; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho). Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs.

  5. Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

  6. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (interim report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    Development was made on a technology to evaluate quality of composite materials. Few data are available for environmental resistance of composite materials, whereas identification of environmental deterioration behavior and establishment of a environmental resistance evaluating technology are a significant issue in utilizing these materials as new materials for space, aeronautics, and marine applications in the future. The present research was taken up with objectives to elucidate deterioration behavior of composite materials exposed to special environment in the atmosphere and space and to establish methods for acceleration tests and environmental performance evaluation by using simulated environments equivalent to the natural environment exposure. The former period (fiscal 1982 through 1984) has investigated environmental conditions in the atmosphere and space, prepared standard test specimens, performed design on environmental devices simulating the environmental elements, as well as tests on deterioration due to environmental elements, and systematized the deterioration characteristics to establish composite test conditions. The latter period (fiscal 1985 through 1988) has developed the composite environment testing device based on the result achieved in the former period, elucidated the deterioration behavior under the composite environmental conditions, and performed evaluation tests on the developed composite materials (FRP). (NEDO)

  7. Research and development of peripheral technology for photovoltaic power systems. Study of nickel-hydride storage battery for photovoltaic generation systems; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo suiso denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of nickel-hydride storage battery for photovoltaic generation systems in fiscal 1994. (1) On the study on low-cost electrode materials, the physical properties and electrode characteristics were studied of the prototype hydrogen absorbing alloys prepared by substituting Cu or Ni for Co in Mm(Ni-Co-Mn-Al)5 (Mm: mixture of rare earth elements). The result clarified that it is difficult to reduce Co content in the alloy to 0.4 atom or less. Simple heat treatment and milling processes in production of hydrogen absorbing alloy electrodes were achieved by adopting an improved metal mold and gas atomization method. Characteristics and cycle life of the Ni positive electrode prepared by applying active paste material of Ni(OH)2 were studied, however, the result showed only lives of nearly 300 cycles. (2) On the study on electrode structure for high-performance (long-life) battery, the 3-D porous metal electrode support was evaluated, and various battery configurations were studied. 11 figs., 1 tab.

  8. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

  9. Fiscal 1974 Sunshine Project result report. R and D on solar energy system (weather survey). Part 2. Guideline for using weather data; 1974 nendo kisho data ni saishite no shishin. 2. Taiyo energy system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    This report describes the guideline for using weather data in R and D on solar energy system. Solar radiation is defined as direct, scattered and reflected radiation in a range of near UV-near IR radiation. Direct solar radiation is observed by silver disk pyrheliometer, while global solar radiation by thermostat or bimetal pyranometer. Accuracy standards of such meters are indispensable to keep the accuracy uniformly. To keep the uniformity and accuracy of observation data all over the world, the international comparative observation is held every 5 years. Solar radiation observation in Japan started in 1932 by installing silver disk pyrheliometers all over the country. In 1938 the observation stations were increased to 79 sites, however, in 1953 those were integrated into 13 long-term weather observation stations. Sunshine duration is defined as the time direct sunbeam aims at the ground, and observed generally by Jordan's heliograph which observes sunshine durations with burned holes on photosensitive recording paper by direct sunbeam through 2 small holes on both sides of a cylinder. The history of statistical processing of solar radiation and sunshine duration data in Meteorological Agency is also presented. (NEDO)

  10. FY 2000 report on the results of the regional consortium R and D project - Regional consortium R and D. Third year report. R and D of the transversal maintenance technology; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium kenkyu kaihatsu. Odanteki maintenance gijutsu no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of eliminating bad effects of the maintenance/management of equipment/facilities of plants which are made separately and of heightening efficiency of work and improving technology, persons in charge of maintenance/management, persons requesting maintenance/management and official research institutes proceeded as one with the construction of a system doing maintenance/management work. Concretely, three parties cooperated in integration and enhancement of element technologies such as inspection/diagnosis and arrangement/repair and developed the maintenance/management system (maintenance center) which does not specify objects. Based on this system, development was made of the network connecting between the center and facilities, diagnosis car, and multi-functional repair car. Studies were made on the following three. As to the system development, conducted were the development of a deterioration mode prediction system, basic structuring of a remote maintenance network, and making of fatigue/corrosion/abrasion database. Concerning the tool development, technology to foresee damages on the static portion such as piping, etc. were developed. In the study of field application, conducted were analysis of maintenance flow, development of retrieval system of equipment parts/personnel/operation procedures and multi-functional repair car, etc. (NEDO)

  11. Fiscal 1997 report on the results of the international standardization R and D. R and D of a mobile office system (R and D of next generation mobile business terminals); 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Mobile office system no kenkyu kaihatsu (jisedai keitai joho kiki no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This R and D is aimed firstly at trially developing next generation mobile business terminals (MBT) based on the technical standards of MBT of which the standards were completed in the fiscal 1996 R and D of Mobile Office Promotion Association (MOPA), secondly at developing an evaluation method for trial terminals and establishing the technical standards of MBT through data communication among different terminals and confirmation of application motions, and thirdly at promoting the international standardization. The study was conducted in the following procedures: 1) making of a comprehensive examination-standardization working group, determination of the use of trial terminals and the MBT evaluation method; 2) trial development of the MBT standards and prototypes; 3) study of the MBT evaluation method; 4) evaluation test on the prototypes; 5) comprehensive evaluation. As the fruit of the study, the evaluation/test specifications were completed, and the evaluation tests among different terminals were conducted. As a result of the evaluation test, the transplantation of MBT managers was done almost with no problems. The MBT adaptability evaluation test was also done almost without problems. 6 figs., 6 tabs.

  12. FY 2000 research and development of fundamental technologies for AC superconducting power devices. R and D of fundamental technologies for superconducting power cables and faults current limiters, R and D of superconducting magnets for power applications, and study on the total systems and related subjects; 2000 nendo koryu chodendo denryoku kiki kiban gijutsu kenkyu kaihatsu seika hokokusho. Chodendo soden cable kiban gijutsu no kenkyu kaihatsu, chodendo genryuki kiban gijutsu no kenkyu kaihatsu, denryokuyo chodendo magnet no kenkyu kaihatsu, total system nado no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project for research and development of fundamental technologies for AC superconducting power devices has been started, and the FY 2000 results are reported. The R and D of fundamental technologies for superconducting power cables include grasping the mechanical characteristics associated with integration necessary for fabrication of large current capacity and long cables; development of barrier cable materials by various methods; and development of short insulated tubes as cooling technology for long superconducting cables, and grasping its thermal/mechanical characteristics. The R and D of faults current limiters include introduction of the unit for superconducting film fabrication, determination of the structures and layouts for large currents, and improvement of performance of each device for high voltages. R and D of superconducting magnets for power applications include grasping the fundamental characteristics of insulation at cryogenic temperature, completion of the insulation designs for high voltage/current lead bushing, and development of prototype sub-cooled nitrogen cooling unit for cooling each AC power device. Study on the total systems and related subjects include analysis for stabilization of the group model systems, to confirm improved voltage stability when the superconducting cable is in service. (NEDO)

  13. Study on the detached house plan using of a maximum natural energy. Part 1; Shizen energy fukugo riyo no keikaku ni kansuru kenkyu. 1

    Energy Technology Data Exchange (ETDEWEB)

    Wada, I; Mino, M; Miyata, T; Okawa, M [Nihon University, Tokyo (Japan)

    1996-10-27

    The geographical position or environment is set on the assumption that the natural energy of a detached house is used in a hybrid state. Moreover, the energy consumption of the house and the natural energy supply obtained from the geographical position were compared and investigated. As a result, the energy consumption is 10,617 kWh, and the energy supply is 8,236 kWh. About 78% of the whole consumption can be theoretically made from natural energy. The energy supply is calculated on the low side during prediction. Therefore, an increase in the energy supply is expected by installing a solar collector based on solar energy, expanding the solar panel area, and increasing the number of wind mills. However, this energy is partially lost via an inverter while it is supplied to the general domestic equipment. At the six main points in Tokyo and its districts, the adaptability of natural energy used based on the regional characteristics is investigated presently and the installation of a system is examined. 13 refs., 2 figs., 6 tabs.

  14. Achievement report on research and development in the Sunshine Project in fiscal 1977. Studies on hydrogen energy total systems and the safety assuring technologies thereon (Studies on hydrogen energy total systems); 1977 nendo suiso energy total system to sono hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso energy total system no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-01

    A numerical model was prepared to express fields and size of hydrogen energy introduction in Japan's energy systems in the future. Dividing Japan into 13 weather sections, one to two energy bases (import and secondary production bases in coastal areas) were assumed on each section. Secondary energies produced in these energy bases are transported to intermediate bases, from which the energies are distributed into cities and consumed. For the purpose of simplification, final consumption departments are hypothesized to exist in these intermediate bases. Parameters that characterize the flows on networks in the processes of supply, distribution, production, storage, transportation and utilization are divided largely into energy efficiency and cost of the processes. The amount of energy demand in each final consumption department was defined as an amount to maximize the expected effects as a result of having satisfied the demand. The result of trial calculations revealed that, as long as the hydrogen to be introduced is limited to hydrogen produced via electrolysis using thermally generated power, the hydrogen introduction into the future energy systems is difficult in terms of economic performance. (NEDO)

  15. FY 1999 report on the results of the R and D of the plant use energy utilization rationalization industrial material production technology; 1999 nendo shokubutsu riyo energy shiyo gorika kogyo genryo seisan gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of using plants to the process to produce energy conservation type/environmentally friendly type industrial materials, the R and D were conducted on the improvement in material productivity/stress resistance of plants by transgenetic technology, etc., and the FY 1999 results were summarized. In the study of the creation of plants to produce industrial materials by genetic recombination of eucalyptus trees, it was found out that early maturing branches of eucalyptus trees were a material suitable for Agrobacterium infection, and conditions to efficiently acquire transformation calluses were obtained. In the R and D of the creation of soybeans to produce polyunsaturated fatty acid, a gene of unsaturated enzyme was acquired from Mortierella alpina storing ultra-long chain polyunsaturated fatty acid, and an experimental study was made to study whether or not this gene functions by plant. Further, studies were conducted on the technology to produce hybrid fiber by salt tolerance plants, creation of plants to produce isoprenoid/natural rubber, technology to produce tissue-specific high proteins, study on the molecular breeding of disease resistant plants, etc. (NEDO)

  16. Report on results for fiscal 1996 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    In fiscal 1996, the initial cooling test and rotary excitation test were conducted for the 70,000kW slow-response type model machine, with the basic characteristics of the rotor verified such as the cooling characteristics, shaft vibration characteristics, mechanical strength, and superconductivity stability, and with the results of the studies explained. The rotor of the 70,000kW slow-response type model was installed in the test site, and the field test was carried out in 1997. For this purpose, research test was performed by the element technology of the model machine and the partial model. The technological development items, trial manufacture and test items were field winding, multi cylindrical rotor and damper. Upon the test results using the element and partial model, the design and manufacturing were implemented of the superconducting generator of a slow-response type excitation method with the output of 70,000kW class. Performed were the basic characteristic test, long-term operation test and severity test on the assumption of abnormality, verifying the characteristics and reliability of the generator as well as obtaining data concerning an excessive electromagnetic force and heat generation. From the test data and the analysis/evaluation results obtained on the model machine, the 200,000kW class pilot machine was reviewed in the conceptual design. (NEDO)

  17. Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 1. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    This report explains the outline as Part 1. In fiscal 1997, the 10th year of the project, a multi cylindrical rotary model for which an in-situ verification test was finished was brought back to the plant and dismantled for examination, while the in-situ verification test of a slow-response type model machine rotor was conducted in combination with a refrigeration system. In addition, in the research of AC wire materials and oxide based materials, studies were made with a purpose of high characterization and long wire materialization. In the metallic materials, a 10kANbTi conductor was developed while, in oxide-based materials, research was done on performance improvement and wire materialization based on various synthesizing methods. The manufacturing, factory test and in-situ text were conducted for a 70,000kW model machine with the purpose of R and D of a 200,000kW class pilot machine. Examination was made on the test method of the 70,000kW class model machine, operation technology of a superconducting generation system, and the effect of introducing the superconducting generator into a power system. In the conventional refrigeration system, a single unit test was carried out for the liquefaction, liquid storing capacity, etc., of the system. The 70,000kW class model machine was put through a test for confirming the general operation including the refrigeration system. (NEDO)

  18. Research and development of photovoltaic power system. Study on structural defects in silicon-based amorphous materials; Taiyoko hatsuden system no kenkyu kaihatsu. Amorphous silicon kei zairyo no kozo kekkan ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

    1994-12-01

    Described herein are the results of the FY1994 research program for structural defects of silicon-based amorphous materials for solar cells. The study on light generation defects of the a-Si:H system and rejuvenation process by annealing establishes the effects of light irradiation time on changed neutral dangling bond density as a result of light irradiation at varying temperature of 77K, room temperature and 393K. The study on annealing to rejuvenate light generation defects of various types of a-Si-H systems establishes the activation energy distribution with respect to annealing to remove light-induced defects, showing that hydrogen affects the distribution of light-induced defects. The study on decaying process of light-induced ESR for undoped and N-doped a-Si:H systems observes the decaying process of light-induced ESR, after light is cut off, extending for a period of several seconds to several hours at 77K for the a-Si-H systems containing N in a range from 0 to 12at%. The other results presented are space distribution of neutral defects of light-irradiated a-Si-H systems, and rejuvenation process of light-induced spin for the a-Si(1-x)N(x):H composition. 6 figs.

  19. Report on achievements in fiscal 1999. Research and development of micro-machine technologies (development of micro-factory technologies); 1999 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho. Micro factory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to achieve energy saving by micronizing the manufacturing processes of small industrial products, this research and development is intended to establish technologies to realize a micro-machine system, in which devices for processing, assembly, transportation and inspection used in the manufacturing processes are unified and incorporated in narrow spaces. Fiscal 1999 has performed, on the items of (1) research and development of the systematizing technologies and (2) comprehensive surveys and researches, with respect to the development of the first prototype system, and fabrication on the trial basis of devices to be mounted on the second prototype system, and discussions on further functional enhancement of the different devices. As a result in the research of the systematizing technology, the first prototype system was developed, that unifies the base unit fabricated in fiscal 1998, the electrolysis processing device, the fluid feeding device, the micro-arms, the coating device, the transportation device, and the environment recognizing device. The basic performances of the individual devices on the first prototype system were verified. Based on the result of this function verification, optimal design and fabrication on the trial basis of the devices mounted in the second prototype system were performed, and discussions were given on the further function enhancement in each functional device. (NEDO)

  20. Research and development of a superconducting flywheel power storage system in fiscal 1998. Research and development of rotation control technology; 1998 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu. Kaiten seigyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Element technology research was performed on 'rotation control' aimed at practical application of a 10-MW class high-temperature superconducting flywheel power storage system. As part of the research, researches were carried out on small-size and middle-size models, low-loss control type magnetic bearing, and large-size models. For the small-size model, as a result of performing performance tests on the protective bearing by using a testing machine, it was revealed that the model is free of problems in the test for up to 5000 rpm. For the middle-size model, fabrication and installation were completed on a middle-size rotation control testing equipment having CFRP-made flywheel with a diameter of 1 m. In the control type bearing, as a result of adopting a homo-polar type magnetic pole, the rotation loss was reduced to about 1/5 of that of a hetero-polar type. The amount is about 75 W (12000 rpm) when the bias current is 1.5 A. Concept design was implemented on a 2-MWh flywheel bearing system supported with a high-temperature superconducting magnetic bearing as a full-size flywheel. The CFRP-made flywheel has a diameter of 4 m, and a circumferential velocity of 1200 m. (NEDO)

  1. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The research and development in the second term included development of raw materials, elucidation of electricity conduction mechanism, and development of methods to improve stability and a new processing method. Crystals of a large number of charge migrating complexes were grown to elucidate their electron properties and structures. A theoretical model was structured for the superconduction mechanism in the charge migrating complexes. Poly-p-phenylene vinylene-based polymers achieved {sigma}=1.1 times 10{sup 4}s/cm as a result of extension of soluble reaction intermediates. Poly-2, 5-phenylene vinylene doped with FeCl{sub 3} retained 10{sup 3}s/m for 165 days in nitrogen. Polypyrrole achieved 3.0 times 10{sup 3}s/cm in constant potential electrolytically oxidizing polymerization and extension at low temperatures. Polypyrrole doped with ClO{sub 4}{sup -} retained electric conductivity of 85% for 400 days in nitrogen. Electric conductivity of higher than 10{sup 5}s/cm was obtained by applying different kinds of doping into thin film and fiber formed graphite. The world's highest conductivity of 9 times 10{sup 5}s/cm was achieved particularly with discharge laminated and polymerized graphite doped with AsF{sub 5}. (NEDO)

  2. Research and development of the industrial basic techniques of the next generation. Composite materials (Final research and development evaluation / Part 1); Jisedai dangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (Saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This R and D project is aimed at development of highly functional materials for aerospace devices, bringing into focus research and development of resin-based composite materials (FRPs), metal-based composite materials (FRMs), and evaluation of their properties and their design techniques. The basic target properties are heat resistance temperature of 250 degrees C or higher and tensile strength of 240 kg/mm{sup 2} or more for the FRPs, and heat resistance temperature of 450 degrees C or higher and tensile strength of 150 kgf/mm{sup 2} or more for the FRMs. This R and D program has been implemented for 8 years for development of raw materials, molding/processing techniques, quality evaluation and designs through information exchange and discussions of the experts in each area under integrated, close cooperation from raw materials to molding/processing. Most of the data indicate that the target properties and objects are satisfied or exceeded. It is therefore concluded that this project for the composite materials, extending for 8 years in 3 phases, has sufficiently achieved the initial objects. The unique techniques are incorporated in the raw materials, molding/processing processes, quality evaluation and designs. These efforts have produced the FRPs and FRMs of the world highest qualities. (NEDO)

  3. Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

  4. Research and development of peripheral technology for photovoltaic power systems. Research and development of redox flow battery for photovoltaic power generation; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo redox denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of redox flow battery for photovoltaic power generation in fiscal 1994. (1) On the production method of electrolyte, silica reduction treatment was attempted to use ammonium metavanadate recovered from boiler as electrolyte of redox flow battery. Silica removal rates more than 90% were achieved by crystallizing V as polyvanadate while keeping molten silica. It was ascertained in minicell experiment that trivalent and quadrivalent V electrolytes produced from recovered V are applicable to continuous charge/discharge operation for one week. (2) On development of battery systems, the relation between battery characteristics and physicochemical properties of carbon fiber electrodes was studied to improve carbon fiber electrodes. The efficiency of 80% was achieved at current density of 160mA/cm{sup 2} by use of layered electrodes, resulting in considerable cost reduction. Performance evaluation operation of the 2kW battery prepared in the last fiscal year was also carried out. 4 figs.

  5. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

  6. Performance analysis on natural energy autonomous house, HARBEMAN house; Shizen energy jiritsu house (HARBEMAN house) no simulation ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujino, T; Saito, T [Tohoku University, Sendai (Japan)

    1997-11-25

    Outlined herein are a procedure developed to simulate performance of an energy-autonomous (independent) solar house referred to as HARBEMAN HOUSE (HH) built in 1996 in City of Sendai, comparison between the simulated and observed results, and characteristics of the solar house. The house is equipped with a solar collector and sky radiator, both installed on the roof, the former facing south to collect solar energy and generate hot water whereas the latter facing north to radiate heat and generate cool water. Both are connected to an underground heat-insulated tank having a capacity of 31m{sup 3}, which stores hot or cool water to keep their conditions for extended periods. The solar system operates in heat- or cool-storage mode. In the heat-storage mode, quantity of heat stored increases, although at a slow rate, as tank capacity increases. In the cool-storage mode, on the other hand, quantity of cool stored increases in proportion to tank capacity. This is because solar energy is collected throughout the year whereas cooling by radiation is concentrated in early spring. Loss rate of heat stored increases as tank capacity increases, and the opposite trend is observed with cool stored. 12 refs., 7 figs., 2 tabs.

  7. Investigation on innovation of technology development by means of strategic energy intelligence; Energy senryakurontekina approach ni yoru gijutsu kaihatsu no kakushin ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of developing the future innovative energy technology, the paper described a strategic point of view. Effects of the energy issue are remarkable on the next generation and thereafter as seen in the finite of energy resource, global-scale environmental changes, the increasing energy demand, natural/social influences of large-scale technology development. If the technological development is going on in the same way as until now, there will appear limits. Relating to the strategies, to seek what energy should be among the strategies, it is necessary to consider not only global-scale problems but particular conditions in Japan (self-sufficiency, international cooperation, creativity, etc.) Also, wisdom and technique are necessary to attain it. Technological development in a wide sense plays a major role in the energy strategy. Technology innovation must be advanced according to the energy strategy. Integrating ideology into the development of energy technology and selecting therefrom developmental subjects which meet the purpose, required is the construction of the energy system with high flexibility and functionality. Looking at the conventional way of thinking from a different angle and posing a future pull plan, Japan should show leadership to the world. 20 refs., 25 figs., 8 tabs.

  8. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

  9. Research and development of photovoltaic power system. Interface studies of amorphous silicon; Taiyoko hatsuden system no kenkyu kaihatsu. Amorphous silicon kaimen no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Konagai, M [Tokyo Institute of Technology, Tokyo (Japan). Faculty of Engineering

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on research on interface of amorphous silicon for solar cells. In research on amorphous solar cells using ZnO for transparent electrically conductive films, considerations were given on a growth mechanism of a ZnO film using the MOCVD process. It was made clear that the ZnO film grows with Zn(OH)2 working as a film forming species. It was also shown that the larger the ZnO particle size is, the more the solar cell efficiency is improved. Furthermore, theoretical elucidation was made on effects of rear face of an interface on cell characteristics, and experimental discussions were given subsequently. In research on solar cells using hydrogen diluted `i` layers, delta-doped solar cells were fabricated based on basic data obtained in the previous fiscal year, and the hydrogen dilution effect was evaluated from the cell characteristics. When the hydrogen dilution ratio is increased from zero to one, the conversion efficiency has improved from 12.2% to 12.6%. In addition, experiments and discussions were given on solar cells fabricated by using SiH2Cl2. 9 figs.

  10. Reports on 1979 result of Sunshine Project. R and D on solar cooling/heating and hot-water supply system (R and D on system for large-sized building); 1979 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Ogata kenchikubutsuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    Equipment was developed constituting a solar cooling/heating and hot-water supply system, as was the system using such equipment as well as being safe and easy to carry out inspection and maintenance, with the purpose of putting into practice an innovative system capable of cooling/heating and hot-water supply for a large-sized building economically by means of solar energy. An analysis was conducted on the test result in an experimental system having a practical size, with the effect confirmed of the improvement work of fiscal 1978. An inspection was made for the cause of piping corrosion, as were the examination and proposal for anti-corrosion measures. Heat and weather resistance tests were carried out on selective absorption films and a convection preventive structure. A selective absorption film processing was performed on a heat collecting plate for a large heat-collecting device, with a durability test conducted for the device by assembling the film in it. A test equipment was designed and manufactured for a latent heat type heat-collecting system of a practical size, performing various experiments and an automatically controlled operation. Displayed in the test by the practical size experiment system (in the Oita University laboratory) were the cooling/heating operation mode, summary of a whole day operation, daily fluctuation of electrical power and kerosene consumption, and a graph of accumulating totals. A long-term/short-term instrumentation analysis were also performed. (NEDO)

  11. Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of advanced-function maintenance technology for power generation facilities; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Technologies for integrating functions are studied for a self-propelled surroundings recognition system that travels in a small-diameter tube at power generation facilities. Parameters are analyzed, and piezoelectric locomotion devices are reduced in size. A disk shape microantenna is experimentally built and evaluated, which is for realizing energy supply and communication by means of microwaves. Studies are conducted to improve the performance of optical energy transmission devices and to realize their systematization. Basic specifications are established for the embodiment of CCD (charge coupled device) microcameras to be installed. A high-efficiency, high-reliability micromachine system is constructed, in which multiple machines coordinate with each other for the exterior inspection of groups of small-diameter tubes. Devices which are capable of driving, deceleration, and propulsion prove to be feasible. Basic specifications are established for microconnectors to connect, separate, and combine multiple machines as occasion calls. Also discussed is the development of a micromachine for tube interior check and repair which operates making use of the inspection hole enabling tube interior check and repair without the need of disassembling the equipment to be repaired.

  12. Development of the advanced load leveling air conditioning technology utilizing unutilized energy; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A heat supply plant utilizing unutilized energy is called for environment-friendly efficient operation including stable heat supply, energy saving, CO{sub 2} emission control and power load leveling. Toshiba developed the optimum operation system for environment-friendly efficient operation considering heat demand prediction and characteristics of a heat supply plant. The demonstration test result showed that this system is effective to reduce power cost of a heat supply plant by nearly 15%. This system was promoted by joint research of NEDO, Heat Pump and Thermal Storage Technology Center of Japan and Toshiba supported by Agency of Natural Resources and Energy, MITI. (translated by NEDO)

  13. Report on the development of the environmentally friendly type high efficiency energy utilization system - Study of the optimum system design technology. Case study of the wide area energy supply network in the Osaka prefectural region; Kankyo chowagata kokoritsu energy riyo system kaihatsu - saiteki system sekkei gijutsu no kenkyu hokokusho. Osakafuiki ni okeru koiki energy kyokyu network no case study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper worked out a model of the wide area supply network which combines the element technology being developed in the eco/energy urban project and the existing technology to apply it to the actually existing city, and the evaluation study was made of energy conservation effects, environmental preservation effects, economical efficiency, etc. The FY 2000 results were reported. In this fiscal year, a case was studied of using the exhaust heat from waste incineration plant by wide area network in the region having a plan of redevelopment/rezoning of the city of Osaka where heat is in great demand. The results of the study were as follows: The total primary energy consumption amount is reduced by 16.3-19.7% in the conventional heat insulation pipe method and by 19.2-20.6% in the vacuum heat insulation method. As to the environmental preservation, the CO2 reduction amount is 36.9-40.0%, and the NOx reduction amount is 43.7-45.5%, which indicated much more improvement than in the present situation. In the aspect of economical efficiency, the result indicated that in the case of the shortest piping, much economical efficiency is expected even without subsidies if considered of the carbon tax. (NEDO)

  14. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research and development of production of low-cost monosilane); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (tei cost monosilane seizoho no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    A low-cost production method is developed for monosilane as a cell film material, 99.9995% pure at a manufacturing cost of 4,500 yen/kg (100 ton/year unit). An experimental unit with a maximum capacity of 1m{sup 3}/H (1 ton/month) gas production is built, and whether it is practical will be clarified by the end of fiscal 1983. The whole monosilane production process, consisting of the electrolysis of eutectic liquid of Li chloride and K chloride, hydrogenation of Li to be generated by the electrolysis, and the generation of monosilane through the reaction of the hydrogenated Li and silicon tetrachloride, proceeds in one large molten salt tub. The chlorine from the electrolysis and Si as material comes into reaction in a salination furnace for the generation of silicon tetrachloride to be supplied to the process. Minor tests are made involving pressure control, distance between the electrodes and the effect of the diaphragm, stirring in the hydrogenation chamber, dust in the monosilane generation chamber, and the insulation of the cathode lead rod, and the results are reflected on the process of experimental unit designing and building. The unit has harm neutralizing facilities for safety assurance because much hydrogen and a little chloride are consumed while the unit is in operation, with some silicon tetrachloride to be retained in the unit. An infrared absorption method is used to analyze impurities in the monosilane gas, when the method exhibits a capability of detecting 2ppm of methane. (NEDO)

  15. Industrial science and technology research and development institutions in fiscal 2000. Research and development of human media (Report on achievements in research and development of high-level information system for petroleum plant); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido. Human media no kenkyu kaihatsu seika hokokusho (sekiyu plant kodo johoka system gijutsu kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Having selected a petroleum refining plant as a large and complex system, a system was developed, that is capable of operating safely and efficiently a plant even by young operators by utilizing the human media technology that realizes information environment having a sense of unity with humans. With this system, if an anomaly is detected in the plant condition, the agent and the operator talk with each other freely, and necessary items of information are displayed on a large screen from moment to moment according to the priority thereof. Activities were taken in the following nine areas: 1) the total system, 2) research on an interface agent, 3) research on hypothetic plant indication interface, 4) research on a discrete cooperative treatment technology, 5) research on plant models and interface systems, 6) research on plant ontology, 7) research on significance indication interface, 8) improvement of tools to structure a large-screen integrated indication system, and 9) investigations on technological trends in foreign countries. (NEDO)

  16. Fiscal 1997 report on the results of the R and D of industrial scientific technology. R and D of synergistic ceramics (R and D of corrosion prevention technology for the petroleum production system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To heighten durability and safety of materials/parts for undersea oil drilling, the development of ceramic base materials was made by developing function harmony type process technology which harmonizes on a high grade contrary characteristics and various functions. The paper summed up the fiscal 1997 results. In the design of system formation, computational simulation technology was developed to the composite process and the diploid system. The development of multifunction simultaneous manifestation materials was trially made by the higher nano structure process. A study was made of control of microstructures of porous materials and matrix filling by the gas phase precipitation control. Proposed were selective control of grain growth from species crystals and the columnar particle orientation laminated structure of simultaneous manifestation of strength and toughness. By composite precipitation reaction control, studied were simultaneous dispersion of whisker and increase in density of matrixes, and harmonization with long fibers. Silicon nitride was trially made with low lubrication/friction coefficients and high strength. A simulation method for crack progress behavior evaluation was developed using a testing notched specimen heterogeneous microstructures. Analyses were made of brittle fracture mechanics and reliability evaluation. 273 refs., 344 figs., 29 tabs.

  17. Report on investigations and studies on chemical conversion of photo-energy; Hikari energy no kagakuteki henkan ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This paper summarizes problems in utilization of solar energy, their solutions, features, the currently achieved results, and prospects. With regard to water decomposition using semiconductors, simultaneous generation of hydrogen and oxygen has already been achieved, and there is high possibility of raising the efficiency by improving catalysts. Water decomposition using metal complexes has acceleration of charge isolation as the largest problem, whose prospect of solution is not necessarily bright at the present time. Photo-catalytic reaction is a field to be discussed as one means of developing a new synthesizing method from the viewpoint of organic synthetic chemistry. Conversion into electric energy that uses a photovoltaic process has high efficiency, and is a field to be noted. In photo-energy conversion by means of photo-synthesis, living organisms performing hydrogen production at high efficiency have been discovered. Important studies include the studies in terms of chemical engineering using these living organisms, improvement of breeds by gene manipulations, and studies that utilize living organisms or part of the constituting components. (NEDO)

  18. Reports on 1979 result of Sunshine Project. R and D on solar cooling/heating and hot-water supply system (R and D on system for existing private house); 1979 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Kison kojin jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-05-31

    The following technologies were developed for the purpose of putting into practice an innovative system that performs cooling/heating and hot-water supply for an existing private house economically by solar energy: (1) development of equipment constituting solar cooling/heating and hot-water supply system, and (2) development of a system which uses such equipment and which is inexpensive and safe as well as easy for inspection and maintenance. The results of the research were as follows. A latent heat type heat storage tank was developed in a small low-loss type in which ammonium alum was selected for a high temperature heat storage tank and in which NaCH{sub 3}COO(center dot)3H{sub 2}O were selected for a combination latent heat/cold water heat storage tank. A refrigerator was developed driven by a small Rankine cycle engine of a result coefficient of 0.47. A flat plate type heat collecting device was developed in a type having a BrNi selective absorbing film and materials of copper tube, aluminum plate and double glass. A vacuum heat collecting device was developed in a high efficient type with the outside dimension of {phi} (diameter) 70 x 1,270 mm, selective absorbing film BrNi, and a degree of vacuum of 10{sup -3}Torr. A heat receiving/releasing storm shutter was developed in a type using a latent heat storing material of paraffin wax. A heat absorbing/insulating outside wall panel was developed using FRP and aluminum as the materials. The system analysis also achieved success. (NEDO)

  19. Research and development of turbofan engine for supersonic aircraft. Choonsokukiyo turbofan engine no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yashima, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1992-01-01

    This paper described the researched results of the demonstrator of a turbofan engine for supersonic aircraft (IHI-17). A turbofan engine with an afterburner was experimentally fabricated and various engine tests have been carried out since 1988. Although the engine size is small, the fighter engine specifications were applied to its design and the prior or simultaneous research on each component was carried out. As a result, the system integration technique by which an engine was assembled by integrating each component could be established. New materials and new manufacturing techniques such as turbine blades of single crystal, turbine disks of powder metallurgy and deep chemical milling for a duct were developed to use for the long term engine test and the prospect to commercialization could be obtained. The following techniques have been established and the results satisfying target specifications could be achieved: the three dimensional aerodynamic design of compressor and turbine, the adoption of air blast fuel atomizer to suppress the smoke generation, an afterburner of spray bar system and the mounting type FADEC (full authority digital electronic control) to control the engine with the afterburner. 4 refs., 15 figs., 4 tabs.

  20. Study on development of adsorbent of acetaldehyde; Acetaldehyde yo kyuchakuzai no kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T. [Nippon Steel Corp., Tokyo (Japan); Suzuki, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

    1997-07-10

    The adsorption of acetaldehyde by porous ceramics impregnated with hydrazinium aluminum sulfate (HAS) is studied. Silicagel, activated alumina, activated clay, and activated carbon are compared, and it is found that silicagel and activated clay are suitable as a substrate for HAS impregnated adsorbent. The adsorption mechanism of acetaldehyde by the adsorbent is believed to be one in which acetaldehyde reacts with hydrazinium and yields acetaldazine. The adsorption capacity of the adsorbent at low acetaldehyde concentration of 0.1 ppm was as large as 1.36 mol/kg. This adsorption capacity at 0.1 ppm acetaldehyde concentration is remarkably larger than that of conventional activated carbon. Hydrazinium decomposes easily in the air because it is a strong reducing agent and reacts with oxygen or carbon dioxide. But hydrazinium impregnated on porous ceramics with HAS becomes more stable and maintains reactivity with acetaldehyde for longer than six months. An adsorbent made of porous ceramics impregnated with HAS is useful as a deodorant for acetaldehyde. 8 refs., 6 figs., 6 tabs.

  1. Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

  2. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

  3. Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Massive rapid identification of gene functions; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Idenshi kino no tairyo jinsoku dotei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are exerted to develop a system for massive and rapid identification of unknown genes through the utilization of techniques based on the unusual membrane fusion characteristics of HVJ (hemagglutinating virus of Japan), which enables the introduction of genes efficiently and uniformly into cultured cells and living organs (development into a kit). Activities are conducted in the three fields of (1) the development of a method for introducing genes using an HVJ envelop vector, (2) a survey of kit marketing and cold storage facilities in the selling and distribution of the kit, and (3) a comprehensive survey. In the field of (1), studies are conducted for the establishment of methods for HVJ envelop vector production and refining, the establishment of an optimized method for encapsulating genes into the HVJ envelop vector, and the introduction of genes into cultured central neurons using the HVJ envelop vector system. A refining method has been established, which comprises the inoculation of HVJ into eggs, 4-day culture, egg cutting, liquid sampling (chorioallantoic liquid), inactivation (addition of alkylating agent), filtration, enrichment (ultrafiltration), and an anion exchange chromatogram. (NEDO)

  4. Performance analysis on natural energy autonomous house (HARBEMAN house); Shizen energy jiritsu house (HARBEMAN house) ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujino, T; Saito, T [Tohoku University, Sendai (Japan)

    1996-10-27

    To reduce fossil fuel consumption and CO2 emission, this article introduces an actually constructed natural energy autonomous house. It has a solar collector on the south roof for hot water supply and a sky radiator on the north roof for cooling water supply. The sky radiator uses radiation cooling phenomena into the space by electromagnetic wave through the window of atmosphere. This house also has an insulated tank with a capacity of 31 m{sup 3} in its underground. In the long-term heat storage mode, the heat is collected through the solar radiation during the period from summer to spring and is stored in the underground water tank, to use it for heating and hot water supply in winter. The heat can be recovered from the garbage waste incinerator. A gas fired auxiliary boiler is used for the shortage. In the long-term heat regeneration mode, the heat is regenerated through the sky radiator during the period from spring to summer and is stored in the underground water tank, to use it for cooling in summer. For the shortage, the water is cooled using a heat pump operated by the midnight power. The insulating performance is improved by using the pair glass in windows and the glass wool in the walls. Rain water is collected in a tank with a capacity of 2 m{sup 3}, to use it for toilet water. Annual energy and water saving is equivalent to 600,000 yen. 10 refs., 10 figs., 2 tabs.

  5. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

  6. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly crystalline polymeric material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo saishu kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    Basic technologies are developed involving highly crystalline polymeric materials comparable to metals in dynamic property even when used singly. The aim is to expand the application scope of polymeric materials including those designed as structural materials so that their light weight, high resistance to corrosion, and excellent machinability may be utilized in various fields. Target performance includes an elastic modulus under bending force of 100GPa or more in anisotropic materials and 50GPa or more in isotropic materials, a linear expansion coefficient of 5 times 10{sup -5}/degrees C or less, and a thermal deformation temperature of 180 degrees C or more. Tasks faced in relation to film or molded articles of anisotropic materials are the rigid molecular design, molding method including molecular orientation control, and molecular complex technology; and, in isotropic materials, the strengthening of interaction between molecules, establishment of molding methods, and equipping materials with high machinability. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. To be mentioned are achievements involving the generation of multidimensionally bound diacetylene polymeric crystals, higher elastic modulus and moldability provided to polyarylate materials, magnetic field orientation, ultrahigh-elasticity layered body, and organic-inorganic ionically bonded complex material, etc. (NEDO)

  7. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the mechanism of light deterioration reaction of photochromic molecules, it was disclosed that 6-nitrospirobenzopyran has the light deterioration caused from the excitation triplet state. This disclosure presents a possibility of preventing the light deterioration. New derivatives that show photochromism were synthesized, and thin films were produced by using the LB process. This indicates a possibility of producing the photochromic materials as the high multiplex recording material. With regard to PHB materials, an evaluation technology having spectrum resolution of the world's highest level was established and measurements were performed. Hole formation was verified for the first time in the world at the temperature higher than the liquid nitrogen temperature by using a PHB material of ionic porphin/polyvinyl alcohol systems. This verification indicates a feasibility of practically usable PHB materials. (NEDO)

  8. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  9. Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

  10. Fiscal 1996 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technologies were described of creating original high-functional materials. The paper presented the following two as fields of technology on which importance is to be placed for the future R and D from technological and socioeconomic points of view. In the field of new materials of living organism imitation type, remarkably high-performance/high-functional new materials are invented by imitating the precise function manifestation mechanism of the ultimate living organism in which a great variety of matters are in harmony with each other and manifest complicated and high-level functions. In the field of structural control/synthesis process technology, the paper is aimed at manifestation of newer and higher functions/performance and innovation of the synthesis process, and also at developing technology to precisely control structure and process of materials including surface and interface in correspondence with atomic/molecular to macro levels. Up to the present, conducted were an examination of autonomous response materials (the subtheme is a R and D of polymer/composite multi-stimuli-responsive materials) and a R and D of precise polymerization (control) polymer materials. 239 refs., 129 figs., 49 tabs.

  11. Present situation of the development of petroleum substitution energy (the U.S.); Sekiyu daitai energy kaihatsu no genjo (Beikoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper investigates and reports the trend of the development of petroleum substitution energy in the U.S. The Clean Coal Technology Plan is one of the plans which were implemented most successfully in the past several years. The plan made a remarkable reduction in NOx and SOx emissions possible. As for natural gas, importance is placed on improvement of production/storage technology of natural gas and high-effective low-NOx-emission turbines. As to the research on nuclear reactors, importance is now placed on the light water reactor plan, and the target is the design and development of such nuclear reactors as electric power companies pay attention to. The solar cell industry is markedly developing, and the shipment grows 17% per year. However, the price is rapidly declining. The wind turbine and biomass power generation plans are also advanced, and most of the plans are aimed at the development of new fields of application. With regard to geothermal energy, slowness is seen. Concerning electric vehicles, no makers enter into the quantity production, but the research and development are actively being made. 72 refs., 26 figs., 51 tabs.

  12. Report on survey in fiscal 2000 on the survey on corporate research and development strategies. 2; 2000 nendo kigyo kenkyu kaihatsu senryaku chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to discuss the ways of the research and development by the government and the private corporations intended to strengthen the international competitive power, surveys have been performed on the current status of collection and analysis of the basic data related to the research and development and the policies to aid research and development and technological development under the governmental organization initiatives in foreign countries. With regard to the trends in the main indexes of research and development activities in Japan, the following different indexes were selected and analyzed: research expense, nature of researches (basic research, applied research, and developmental research), trends by business types, trends in patents, trends in technology trades, trends in technology introduction, and research and development expense. These items are in addition to the macro index for the research and development activities per GDP. With regard to the research and development strategies in foreign countries, the 'DOE Research and Development Portfolio' summarizing the energy strategy by the U.S. Department of Energy, and the 'Science Research Priorities' published by the British OST were selected and discussed. The discussion was intended to analyze the actual status and the results of research and development by using governmental funds in foreign countries. (NEDO)

  13. Report on survey in fiscal 2000 on the survey on corporate research and development strategies. 2; 2000 nendo kigyo kenkyu kaihatsu senryaku chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to discuss the ways of the research and development by the government and the private corporations intended to strengthen the international competitive power, surveys have been performed on the current status of collection and analysis of the basic data related to the research and development and the policies to aid research and development and technological development under the governmental organization initiatives in foreign countries. With regard to the trends in the main indexes of research and development activities in Japan, the following different indexes were selected and analyzed: research expense, nature of researches (basic research, applied research, and developmental research), trends by business types, trends in patents, trends in technology trades, trends in technology introduction, and research and development expense. These items are in addition to the macro index for the research and development activities per GDP. With regard to the research and development strategies in foreign countries, the 'DOE Research and Development Portfolio' summarizing the energy strategy by the U.S. Department of Energy, and the 'Science Research Priorities' published by the British OST were selected and discussed. The discussion was intended to analyze the actual status and the results of research and development by using governmental funds in foreign countries. (NEDO)

  14. Fiscal 1999 survey report. Survey and research concerning development of next-generation chemical process technologies; 1999 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To further enhance resource/energy conservation and environmental impact reduction, it is necessary to develop innovative chemical reaction process technologies. It is for this reason that 'development of next-generation chemical reaction process technologies' is being carried out under the New Sunshine Program. The survey and research, for the fulfilment of the above goal, aim to select important technologies and put in a easy-to-study order the problems contained in associated technologies for picking out tasks for future studies for the purpose of suggesting some subjects to be taken up for future development. In addition, studies are made about how a comprehensive technology assessment system should be. In this fiscal year, propositions are compiled for research and development projects on five subjects. Studies of subjects other than these five will also continue to eventually build concrete propositions on them. The said five subjects involve 1) the development and application of nonaqueous biotechnologies, 2) biotechnology-aided polymeric material creation processes, 3) construction of high-efficiency energy conservation processes using innovative grain handling technologies in the high-temperature reaction field, 4) manufacture of high-performance polymeric materials for batteries and development of battery fabrication processes, and 5) the development of an energy conservation process maximally utilizing environmentally-friendly polyolefin. (NEDO)

  15. Fiscal 1999 survey report. Survey and research concerning development of next-generation chemical process technologies; 1999 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To further enhance resource/energy conservation and environmental impact reduction, it is necessary to develop innovative chemical reaction process technologies. It is for this reason that 'development of next-generation chemical reaction process technologies' is being carried out under the New Sunshine Program. The survey and research, for the fulfilment of the above goal, aim to select important technologies and put in a easy-to-study order the problems contained in associated technologies for picking out tasks for future studies for the purpose of suggesting some subjects to be taken up for future development. In addition, studies are made about how a comprehensive technology assessment system should be. In this fiscal year, propositions are compiled for research and development projects on five subjects. Studies of subjects other than these five will also continue to eventually build concrete propositions on them. The said five subjects involve 1) the development and application of nonaqueous biotechnologies, 2) biotechnology-aided polymeric material creation processes, 3) construction of high-efficiency energy conservation processes using innovative grain handling technologies in the high-temperature reaction field, 4) manufacture of high-performance polymeric materials for batteries and development of battery fabrication processes, and 5) the development of an energy conservation process maximally utilizing environmentally-friendly polyolefin. (NEDO)

  16. Report on current status of petroleum substituting energy development in the EU in FY 1997; 1997 nendo chosa hokokusho (sekiyu daitai energy kaihatsu no genjo (EU))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The EU is one of the most advanced places of petroleum substituting energy development. The EU is highly aware of environmental issues. For the COP3 held at Kyoto in December 1997, The EU gave more severe regulation of CO2 emission than the other advanced countries. The EU takes efforts in the development and introduction of energy effective for global environmental protection. In addition, research and development of geothermal, biomass and wave force energy are actively promoted in this place. Energy situations in this place are significant for predicting and analyzing the future trends of energy development and consumption in the other countries. Firstly, this report looks back toward energy demand held in check to a head at the beginning of the 1990`s. Secondly, supply of energy and cover of energy trend are described for recent years from the point of view. Thirdly, competitiveness of energy in EU countries are discussed from a position of energy density. Fourthly, circumstances about environmental issues are considered. Fifthly, the world market of energy is also considered. Finally, development of new energy and a trend of introduction with a sample of Sweden are introduced. 13 refs., 15 figs., 28 tabs.

  17. Study on water desalination system by solar energy distillation; Taiyo energy wo riyoshita joryugata kaisui tansuika system no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nagai, M; Ameku, K; Yonamine, K [Univ. of the Ryukyus, Okinawa (Japan)

    1997-11-25

    Discussions have been given on developing a seawater desalination system by solar energy distillation. The system is composed of evaporators installed on the seawater level, condensers placed on high and cool locations, and steam transport pipes to connect these two pieces of equipment. Steam is generated from seawater heated by solar heat in evaporators, and the steam is transported driven by low power consuming fans to higher locations through the steam transport pipes, where it is condensed by cool air in the condensers, and recovered as plain water. The concept is such that electric power required to operate the fans is supplied from photovoltaic panels, and all other energy is obtained from the sun. First, an experiment was performed upon noticing on methods of transporting and condensing the steam. The experiment used plain water rather than seawater. The heat source and evaporators were installed on the first floor, and the steam transporting fans on the second floor of an atrium. The thermal load was set to 1.5 times greater than average outdoor insolation amount. Increase in the distilled water recovery rate and distillation efficiency was verified by using the fans. The evaporation efficiency was found to tend to increase when the steam flow rate is increased. 3 refs., 10 figs.

  18. Fiscal 1998 research report on application technology of molecular assemblies for a functional protein system (Development of advanced maintenance technology for power plants); 1998 nendo kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu. Hatsuden shisetsuyo kokino mentenansu gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Basic research was made on engineering reappearance and industrial use of the complex function of molecular assemblies for a functional protein system of organisms. In research on a light controllable reaction system by physicochemical technique, construction of a light controllable bioreactor is in promotion. In research on a light controllable reaction system by biochemical technique, researches are in promotion on structure and correlation analysis of photosynthetic protein complex, stabilization of an activity, and conversion of light energy to membrane transport energy using cyanobacteria as material. In research on a molecular recognition controllable reaction system in a fine membrane region, correlation analysis of the structure and function of glutamine receptor channels is in promotion. In addition, researches were made on reconstitution of endocytic micromachinery, a multi-enzyme system for synthesis of glycosphingolipids, a complex redox system by genetic engineering technique, and application technology of molecular assemblies for a functional protein system. (NEDO)

  19. Development of large scale wind energy conservation system. Development of large scale wind energy conversion system; Ogata furyoku hatsuden system no kaihatsu. Ogata furyoku hatsuden system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for development of large scale wind energy conversion system. The study on technological development of key components evaluates performance of, and confirms reliability and applicability of, hydraulic systems centered by those equipped with variable pitch mechanisms and electrohydraulic servo valves that control them. The study on blade conducts fatigue and crack-propagation tests, which show that the blades developed have high strength. The study on speed-increasing gear conducts load tests, confirming the effects of reducing vibration and noise by modification of the gear teeth. The study on NACELLE cover conducts vibration tests to confirm its vibration characteristics, and analyzes three-dimensional vibration by the finite element method. Some components for a 500kW commercial wind mill are fabricated, including rotor heads, variable pitch mechanisms, speed-increasing gears, YAW systems, and hydraulic control systems. The others fabricated include a remote supervisory control system for maintenance, system to integrate the wind mill into a power system, and electrical control devices in which site conditions, such as atmospheric temperature and lightening, are taken into consideration.

  20. Reports on 1979 result of Sunshine Project. R and D on solar cooling/heating and hot-water supply system (R and D on system for newly built private housing); 1979 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Shinchiku kojin jutakuyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    This report is for the results of fiscal 1979 on a solar cooling/heating and hot-water supply system for newly-built private housing. The research reports for fiscal 1974 to 1978 are as reported so far; for example, the research on energy-saving construction including thermal insulation method was used in an experimental housing completed in fiscal 1976. The solar heat collecting device was built in the experimental housing by increasing the scale of and utilizing the heat collecting device of a vacuum glass tube type on which research was done before fiscal 1975. The absorption refrigerating machine incorporated in the housing was of a forced circulation type which was high in temperature stability using the result of the research carried out until then. In fiscal 1979, as in fiscal 1978, one year residential experiment was conducted in which a family of a couple and two children lived in a house under an improved system as a result of a system variation and the like, and made an evaluation on the performance. Simultaneously, a control management system was developed in which a micro-computer was introduced for the purpose of improving the system performance, with the operation carried out under the micro-computer control. In addition, a fundamental experiment was also completed concerning a long-term heat accumulation by underground heat reserve. (NEDO)

  1. Report on an industrial machinery engineering policy study meeting. Studies on new energy industries; Sangyo kikai engineering seisaku kenkyukai (shin energy sangyo no kenkyu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-07-01

    Effects extended to industrial areas by new energy development were analyzed by using the industrial relation table. Technological development of new energies can mass-produce energy without being restricted by energy resource availability, and retaining manufacturing facilities can exhibit energy reserve function with security. The technologies may be suitable for local energy supply. In the aspects of industrial policies and people's living, demands on diversification and improvement of the people's living may be responded, levels of scientific technologies may be enhanced, and contribution to improving the industrial structure may be expected. The energy industry includes a large number of related industries and has vast related areas. A large number of technology induced effects can be expected in the course of research and development. A market of huge size may be estimated in the future, by which level elevation of the industrial structure would be supported. Early promotion of the new energy development is an urgent assignment for the 1980's. In order to achieve this goal, it is necessary to promote research and development, proliferation and practical application, for which the physical strength of the present Japan must be utilized to its maximum in making human and fund investments. Expansion and improvement in the industrialization infrastructures are also important, whereas the government's subsidies must be increased, and vitality in the private sector must be incorporated into organized force. (NEDO)

  2. Research and development of technologies for CO{sub 2} fixation and effective utilization thereof, etc., in fiscal 1998. Report on research and development of technologies for the effective use of CO{sub 2} by virtue of contact hydrogenation (CO{sub 2} separation and recovery system of the next-generation type); 1998 nendo nisanka tanso koteika yuko riyo gijutsu nado kenkyu kaihatsu jigyo. Sesshoku suisoka hanno riyo nisanka tanso yuko riyo gijutsu kenkyu kaihatsu jigyo kenkyu kaihatsu jigyo (jisedaigata shoene CO{sub 2} bunri kaishu system ni kansuru chosa kenkyu hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches were conducted for the goal of proposing a totally new process enhanced in efficiency and energy saving, and capable of CO2 separation. In fiscal 1997, hydrocarbon materials were reformed by oxygen separated within a system allowing fuel cells to generate power efficiently, when all the emitted CO2 was separated and recovered within the system. Furthermore, cold heat was utilized for the acquisition of liquefied CO2 gas products. A part of oxygen separated at the fuel cell cathode was recycled into the combustion section external to the tubular reaction reformer, and CO2 was separated by mere cooling from the combustion products for the simultaneous production of by-products such as high-purity nitrogen gas and liquefied CO2 for a great improvement in economy. In fiscal 1998, the system was improved. Proposed then was a new system in which an oxygen partial oxidation type reformer assumed the nuclear role, separating all the oxygen at the cathode, reusing part thereof for oxygen enrichment, and feeding the rest thereof into the reformer. The design realized the recycling of the whole of the products of the two cell electrodes into the reformer for the maximum reuse of the products of the hydrogen/oxygen separation function. (NEDO)

  3. Research and development of photovoltaic power system. Optimization of bandgap of chalcopyrite semiconductors; Taiyoko hatsuden system no kenkyu kaihatsu. Kinseitaihaba no saitekika no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Konagai, M [Tokyo Institute of Technology, Tokyo (Japan). Faculty of Engineering

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on research on research on optimization of bandgap in thin film compound solar cells. In research on Cu(InGa)Se2 thin film solar cells by using a gas phase selenide making process, discussions were given on optimizing the following three processes: a process to raise temperature of a precursor film formed at a substrate temperature of about 150{degree}C, a selenide making process to perform annealing at about 500{degree}C, and a temperature reducing process. Good characteristics were obtained when selenium amount in the precursor is about 50%. In a bandgap control viewpoint, it was found that the conversion efficiency decreases rapidly when Ga composition is higher than 50%. A conversion efficiency of 14.9% was obtained to date at the Ga/(In+Ga) ratio of 0.4. In research on Cu(InGa)Se2 thin film solar cells by using a simultaneous deposition method, a conversion efficiency of 13.5% was obtained at a bandgap width of about 1.3 eV during research on manufacturing ZnO/CdS/Cu(InGa)Se2 thin film solar cells by using the simultaneous deposition method. Research has been carried out on manufacturing Cu(InGa)Se2 thin film solar cells using ZnSe interface layers. 8 figs.

  4. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / development of nano-structured materials for ceramic bearing application (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / ceramic bearing yo nano seigyo zairyo no kenkyu kaihatsu (daiichi nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing high efficient ceramic bearing using nano-structured materials, technical development was proceeded with of raw material powder treatment, forming sintering, processing, structural analysis, property evaluation, etc. As to the study of manufacturing of ceramic balls, the following were conducted by the method developed at Osaka Prefectural Institute of Industrial Technology: coprecipitation laminate processing of ZrO2-Al2O3 system to alumina powder at Okumura Crucible Mfg. Co. Ltd., spherial press processing and sintering at Kyocera Co. Ltd., and precise machining at Nippon Pillow Block Mfg., Co. Ltd. The performance as bearing was measured of the ceramic balls obtained such as surface coarseness, sphericity, crush strength and fatigue life. Surface coarseness and sphericity were the same as those of bearing use silicon nitride, but crush strength was considerably low. In the experiment on rolling fatigue strength as bearing, separation occurred within 100 hours even at a load of 100kgf. It is thought that this is because of the pores remaining on the surface, and the measures to be taken for long life were studied. 12 refs., 64 figs., 27 tabs.

  5. Report on an industrial machinery engineering policy study meeting. Studies on new energy industries; Sangyo kikai engineering seisaku kenkyukai (shin energy sangyo no kenkyu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-07-01

    Effects extended to industrial areas by new energy development were analyzed by using the industrial relation table. Technological development of new energies can mass-produce energy without being restricted by energy resource availability, and retaining manufacturing facilities can exhibit energy reserve function with security. The technologies may be suitable for local energy supply. In the aspects of industrial policies and people's living, demands on diversification and improvement of the people's living may be responded, levels of scientific technologies may be enhanced, and contribution to improving the industrial structure may be expected. The energy industry includes a large number of related industries and has vast related areas. A large number of technology induced effects can be expected in the course of research and development. A market of huge size may be estimated in the future, by which level elevation of the industrial structure would be supported. Early promotion of the new energy development is an urgent assignment for the 1980's. In order to achieve this goal, it is necessary to promote research and development, proliferation and practical application, for which the physical strength of the present Japan must be utilized to its maximum in making human and fund investments. Expansion and improvement in the industrialization infrastructures are also important, whereas the government's subsidies must be increased, and vitality in the private sector must be incorporated into organized force. (NEDO)

  6. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research and development of technologies for enlarging amorphous solar cell area); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (amorphous taiyo denchi no daimensekika gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In the basic studies of large-area a-Si film formation technologies, the validity is discussed of the evaluation technique using plasma optical emissions spectrometry (OES) employed for the achievement of the intended film qualities. The film forming condition that exerts the greatest influence on the plasma state relative to OES is the power of discharge, and correlations are found to exist between specific emission intensity, infrared absorption level, and photoconductivity of the film. It is found that a P- or B-doped Si:H/SiC:H film is suitable as the material for the window layer on the light-receiving surface of the solar cell. Materials are studied for the i-layer responsible for photo carrier generation, isolation, and acceleration. Studies are also conducted on fluorine-containing film. In the efforts at designing and building solar cells, ITO (indium-tin oxide)/n-i-p/SS (reversed type) cells are analyzed, designing is carried out for transparent electrode film thickness optimization, window effect in stainless substrate cells is improved, glass substrate cells are experimentally built and analyzed, large-area solar cell properties are improved, interaction between the substrate and a-Si is studied, and reliability tests are conducted. For cost reduction, it is necessary to develop technologies of automated production of simplified-structure modules using low-cost materials. Basic matters are taken up for discussion. (NEDO)

  7. Achievement report for fiscal 2000 on operational research of human cooperative and coexisting (humanoid) robot system. Development of energy usage rationalizing technology; 2000 nendo ningen kyocho kyozongata robot system un'yo kenkyu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper reports the achievements in fiscal 2000 in the operational research on the human cooperative and coexisting (humanoid) robot system to rationalize energy usage. Operational method and maintenance were studied on the platform hardware that has been developed in the previous fiscal year. Checks were given periodically on the robot platform hardware, and no anomalies were verified in all operation. Verifications were made on the fasteners, additional tightening, fitting of the connectors, battery checks, zero position and step response checks, and output checks on the force component sensor, gyro sensor and G sensor. For the virtual robot platform, discussions were given on the basic movement library for the geography complying three-dimensional walking. Such configurations were constituted that integrated use is possible with the simulator system by connecting the networks, and the user can instruct the CORBA server with the generation of walking movements according to the GUI by using the general purpose WWW browser to connect it to the HTTP server, whose result can be verified by three-dimensional graphics. A method to stabilize the all-axis movement servo model was made open to public. (NEDO)

  8. Research and development of the industrial basic technologies of the next generation, 'composite materials (fine ceramics)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fine ceramics'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-30

    The results of the first phase research and development project for developing fine ceramics as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop fine ceramics of high strength, corrosion resistance, precision and wear resistance, noting their excellent characteristics. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at development of silicon nitride and silicon carbide for synthesis of the stock materials; explosive forming/treating the stock powders; forming, sintering and processing/joining; evaluation of the characteristics; non-destructive testing methods; designs; and evaluation of the parts, among others, as the elementary techniques for production, evaluation and application of the fine ceramic materials. The technical targets of improving functions have been achieved, or bright prospects have been obtained therefor in development of the techniques for synthesis of the stock materials, forming/sintering and processing/joining. The silica reduction for stock synthesis, basic techniques for molding/sintering, and rheological considerations for the molding/sintering techniques represent the techniques of the next generation, because they break through the limitations of the conventional techniques. (NEDO)

  9. Industrial science and technology research and development institutions in fiscal 1999. Report on achievements in research and development of human media; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to give the society with the full picture of human media at an early time, actual problems in industries were taken up. This paper summarizes the sensitivity agent to support sensitivity of individuals, the human media database, the urban environment human media aiming at symbiosis of nature with artificial environment, and the achievements of comprehensive investigations and researches in fiscals 1999 and 2000. Activities were taken in the following four areas: 1) research and development of the sensitivity agent and human media database, 2) research and development of the urban environment human media, 3) comprehensive investigations and researches, and 4) investigations on technological trends in foreign countries. In Item 1), discussions were given on the technology to present full-color images at high accuracy, the image sensitivity retrieval technology, and the multi-dimensional interface technology for the human media database. In studying the basic human media technology, discussions were given on the basic sensitivity modeling technology, and the sensitivity agent mechanism. (NEDO)

  10. Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'Taikankyo kyoka soshi'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-31

    In the research and development of the environment resistance strengthened elements with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments, the second term has developed an integration technology and its evaluation technology based on the achievements in the first term. In developing the heat resistant element technology, the technology to grow {beta}-SiC crystals was expanded to obtaining thin film crystals with high migratory performance by using higher temperatures. At the same time, development was performed on a technology to manufacture multiple number of transistors on one substrate, such as the doping technology and etching technology. Using this technology, schottky diodes and p-n junction elements being the basic structures of MES-FET and bipolar transistors were fabricated. In the evaluation and testing technology, the {gamma} dose measuring method using TLD was improved, the traceability of {gamma} ray irradiation amount was assured, the simplified irradiation testing method using X-ray was established, and the heat resistance testing technology for electronic parts was established. Furthermore, attempts were made on enhancing radiation resistance of the elements, such as in MOS silicon integrated circuit, bipolar silicon integrated circuit, and compound semiconductor integrated circuit. (NEDO)

  11. Research and development of basic technologies for next-generation industry. Evaluation of 1st-phase research and development of 3-dimensional circuit devices; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Sanjigen kairo soshi daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The aim is to develop basic technologies relating to 3-dimensional circuit devices with an ultrahigh-density accumulation of functions therein for the embodiment of ultra-small high-performance data processing devices or artificial brain-like multiple-function data processing devices. To be developed are laminate-structure devices which have an ultrahigh-density accumulation of logic and memory functions or a complex accumulation of functions including signal and sensor functions. In the 1st phase, importance is attached to the development of a multilayer crystalline structure, which is the most elementary in the development of 3-dimensional circuit devices, and of processing technologies for them. Propositions are made and analyses are conducted relating to the enlargement of exposure region in synchrotron radiation lithography, development of a maskless beam process of a resolution of 0.1{mu}m, development of a focused ion beam device, etc. Recrystallization methods using a laser beam or a linear electron beam are developed for the growth of multilayer crystals, and are proved to be effective. The application feasibility of a flat deposition dry process etc. to laminate processing technologies is demonstrated. Concerning integration technologies, some laminated circuit devices are experimentally fabricated, and their behavior is determined. The goals of the 1st phase are found achieved. (NEDO)

  12. FY 1999 report on the results of the R and D of femtosecond technology. R and D of femtosecond technology; 1999 nendo femto byo technology no kenkyu kaihatsu seika hokokusho. Femto byo technology no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project aims at creating new industrial basement technology which supports the highly information-oriented society in the 21st century, conducts the R and D of technology to control the state of light and electron in the femtosecond time domain (10{sup -15} - 10{sup -12} sec), and establishes the basement technology which exceeds the speed limit of the conventional electronics technology and also includes new functionality. The themes are as follows: 1) R and D of ultra-short pulse optoelectronic technology; 2) R and D of ultra-short optical pulse applied measuring technology. In 1), in addition to the investigational study of the ultra-high speed light source technology, ultra-high speed modulation technology and ultra-high speed switching technology which are needed for the ultra-high speed optical information communication system and the construction, made were the survey and the evaluation of crystal growth technology/process technology of new semiconductor materials which make the fabrication of these high-tech ultra-high speed devices possible. In 2), investigationally studied were the technology for generation/control of ultra-short optical pulse and ultra-short electron beam pulse and the technology for stabilization, and the technology for generation of femtosecond high-intensity X-ray pulse by collision of optical pulse with electron beam pulse. (NEDO)

  13. Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'taikankyo kyoka soshi'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-30

    Research, development and evaluation were performed with an objective of developing environment resistance strengthened elements, with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments. The objective for the first term is to develop the basic technology on element structures required to raise the environment resistance, and the methods of testing them. With regard to heat resistant elements, {beta}-SiC single crystal thin films were formed, and a prospect was obtained on using them as the elements. Regarding MOS integrated circuit, bipolar integrated circuit, and GaAs element, points presenting the largest issue in radiation resistance were noticed according to respective elements. Thus, temperature for gate oxide film formation was lowered, element structures were improved, and gate lengths were decreased to enhance the radiation resistance. For the evaluation test technology, a provisional testing method was prepared for the radiation resistance, a prototype in-situ irradiation testing device was fabricated and so was a prototype high-temperature testing device usable up to 500 degrees C. These achievements lead to a belief that the targets for the first term have been achieved. (NEDO)

  14. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

  15. FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)

  16. Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

  17. Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

  18. Performance analysis on borehole energy storage system including utilization of solar thermal and photovoltaic energies; Taiyonetsu hikari riyo wo fukumu borehole energy chozo system no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T [Tohoku University, Sendai (Japan); Yamaguchi, A [Matsushita Electric Co. Ltd., Osaka (Japan)

    1996-10-27

    A permanent borehole energy storage system utilizing solar energy and waste heat from coolers is simulated, to be used as an air conditioning system for super-tall buildings. A 100m-long pipe is buried vertically into the ground, and a heat medium is caused to circulate in the pipe for the exchange of heat with the soil. Thirty borehole units are used, each measuring 9m{times}9m (with the pipe pitch being 3m). Solar cells occupying half of the wall surface facing south and solar collectors installed on the roof supply electric power and heat for cooling and warming. Heat in the ground is transferred mainly by conduction but also is carried by water and gas in movement. So, an analysis is carried out using an equation in which heat and water move at the same time. Because waste heat from cooling and warming systems is accumulated in the ground and none is discharged into the air, big cities will be protected from warming (from developing heat islands). As compared with the conventional boiler-aided air conditioning system, a hybrid borehole system incorporating solar collectors and solar cells will bring about an 80% reduction in CO2 emission and annual energy consumption. 7 refs., 3 figs., 4 tabs.

  19. Studies on plant materials as energy resources 2. Jojoba-new raw material for industry. Energy-gen to shiteno baiomas no tansaku to hyoka ni kansuru kenkyu dai 2 ho. Miriyo YURYO shokubutsu hohoba saibai no genjyo to kaihatsu jyo no kadai

    Energy Technology Data Exchange (ETDEWEB)

    Suganuma, Hirotoshi.

    1989-02-01

    The studies have the objective of searching and evaluating biomass as energy resources and in this report, the current situation and the issues concerning development of cultivation of jojoba which has been an unused oily plant growing in arid and semi-arid areas in the southwestern USA. Its summary is as follows: (1) Jojoba is cultivated experimentally over about 20,000ha in the tropical and semitropical arid and semiarid regions at the almost same latitudes of the areas where it grows wild, (2) With regard to the areas qualified for development in the Chaco region of the western Paraguay, the La Rioja Province in the northwestern Argentina and the Eastern Province in the eastern Kenya, ample production can be expected judging from their natural environmental conditions and the growing characteristics of jojoba. (3) Jojoba is a dioecious plant and it takes 4-5 years from seeding to flowering. During this period, its sex difference cannot be identified, but a conclusion was obtained that the sex difference might possibly be identified by the isozyme method at its stage of young seedlings. (4) When cultivation techniques are firmly established and its price goes down to about 2 dollars/kg, jojoba becomes promising as substitute for sperm whale oil. 20 refs., 8 figs., 18 tabs.

  20. FY 2000 report on the results of the R and D of femtosecond technology. R and D of high intensity X-ray pulse use power generation facility monitoring system; 2000 nendo femto byo technology no kenkyu kaihatsu seika hokokusho. Kokido X sen pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project aims at creating new industrial basement technology which supports the highly information-oriented society in the 21st century, conducts the R and D of technology to control the state of light and electron in the femtosecond time domain (10{sup -15} - 10{sup -12} sec), and establishes the basement technology which exceeds the speed limit of the conventional electronics technology and also includes new functionality. Especially, in the R and D of the high intensity X-ray pulse use power generation facility monitoring system, the establishment is aimed at of the basement technology toward the realization of non-stop inspection of high speed moving objects of power generation facilities, etc. using femtosecond high intensity X-ray pulse generated in the interaction between femtosecond optical pulse and high density electron beam pulse. In this fiscal year, femtosecond X-ray was successfully generated. The pulse width of X-ray: 400fs, the wavelength: 6 angstroms, the X-ray dose generated in one collision: 10{sup 4} photons/pulse or more, and the energy of electron beam colliding with laser optical pulse: 12 MeV. Moreover, developed were the laser amplifying system and the stabilized high power femtosecond laser system. (NEDO)

  1. Research and development of basic technologies for the next generation industries. Summary of research achievements in fiscal 1992 (Research and development of superconductor materials and superconductor elements); Jisedai sangyo kiban gijutsu kenkyu kaihatsu 1992 nendo no kenkyu seika no gaiyo. Chodendo zairyo chodendo soshi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    With an objective to establish basic technologies, research and development has been carried out to make it possible to utilize high-temperature superconductor materials in terms of engineering in the fields of electronics and electric power. In the research on superconductor materials in fiscal 1992, it was discovered from measurements of temperature change in polarization dependent EXAFS in thin YBCO film grown on an MgO substrate that relative displacement in copper atoms in CuO{sub 2} plane and peak oxygen, and relative displacement in copper atoms on a primary chain and peak oxygen show apparent increase at the critical superconduction temperature. It was verified that this phenomenon does not occur in materials that do not show superconduction. In the research and development of superconductor elements, full-swing research has begun toward establishing the following technologies: process technologies for a substrate that meets requirement of surface flatness required in electronic elements, a superconductor thin film that assures uniformity in interface composition and the laminated thin film tunnel junction that combines the superconductor thin film, an inter-layer insulation film, and ultra-fine processing to suppress deterioration, and a tunnel element technology as a technology to put the above technologies together. (NEDO)

  2. FY 2000 report on the results of the technology development of energy use reduction of machine tools, etc. Technology development of environmental load reduction related to water soluble lubricating oil, etc. (R and D of low energy coolant degradation prevention technology and waste liquid processing technology); 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Suiyosei junkatsuyu ni kakawaru kankyo fuka teigen nado gijutsu kanri (tei energy coolant fuhai boshi gijutsu oyobi haieki shori gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were carried out on a system by which the long life of coolant of machine tools can be achieved and a system to process waste efficiently, economically and with less environmental loads, and the FY 2000 results were summed up. In the R and D of a system to prevent degradation of low energy coolant, measurement was made of effects of the degradation prevention system at a laboratory level, and it was found out that propagation of bacteria causing the degradation can be prevented with pH kept high. Further, it was admitted that the alkali effect on metal formability was not very much. As to the coolant processing, in the present situation, most of the coolant is taken back by industrial waste processing dealers. So, the development of the low energy waste liquid processing system is earnestly desired. In the R and D of the low energy waste liquid processing system, test on characteristics evaluation was conducted about each method of systems. Subjects to be improved/solved were extracted such as the point that volatile organic matters are included in condensed water after evaporation of waste liquid and there seems to be a possibility of needing the secondary processing. (NEDO)

  3. Fiscal 1998 research report. Industrial science and technology research project / R and D on creative advanced functional materials (structure-controlled materials) / Harmonized molecular materials; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) seika hokokusho. Bunshi kyocho zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    R and D on harmonized molecular materials aim at establishment of the technology fabricating self-assembled organic molecular films on solid surfaces which have potentials of mechanical response to electric fields, electroluminescence or optical functions. Molecule harmonization expresses new structures and functions difficult to be expressed by each molecule alone, by cooperative interaction between molecules due to noncovalent bond. Functional thin films were developed by controlling alignment and/or arrangement of molecules with an aid of self-assembling processes. Thiol compounds with larger dielectric anisotropy were synthesized as electric field responsive self-assembled films. {pi}-conjugated compounds composed of phenyl-capped oligothiophenes were synthesized as electroluminescent self-assembled films, and their high crystallinity and efficient electroluminescence were found. Heat- and solvent-resistant lyotropic liquid crystalline (LLC) aligning polymers such as polyamine and polyimine were synthesized as new optically functional LLC dye self-assembled films. (NEDO)

  4. Report on current status of petroleum substituting energy development in the USA in FY 1997; 1997 nendo chosa hokokusho (sekiyu daitai energy kaihatsu no genjo (Beikoku))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In the last twenty-five years, the level of social recognition for the importance of energy conservation grew progressively from a total nonexistence of concern to the driving force that ensures the future environmental health of the nation and the world. Executive Order 12003, relating to energy policy and conservation, was signed by President Jimmy Carter and dated July 20, 1977. In 1992, President Clinton issued Executive Order 12759 - federal Energy Management. Each agency will prescribe policies under which its industrial facilities in the aggregate increase energy efficiency by at least 20% in fiscal 2000 in comparison to fiscal 1985. Current Federal programs for building efficiency are estimated to result in 31.5 billion dollars in annual energy saving for consumers by 2010. Future trends attract attention. The major programs currently in force to implement these policies and directives include Rebuild America, Million Solar Roofs Initiative, Home Energy Rating Systems, and Weatherization Assistance Program. 37 refs., 1 fig., 6 tabs.

  5. Report on the FY 1999 R and D survey on ultra-high sensitive photoelectric converter; 1999 nendo chokokando koden henkan soshi ni kansuru kenkyu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the ICB method which is one of the ion engineering methods, photomultipliers were formed using organic dye thin films. By changing the energy to bond traps on thin film/metal electrode interface and electric charges by change of acceleration energy of ion beams, a technology was developed for adjusting the optimum operating temperature between -20 degrees C and +100 degrees C. The wide range of operating temperature and favorable SN ratio can be realized. It was made clear that the dark current of the photomultiplier is composed of two components of contribution by the residual charge stored on the interface at photomultiplying and of contribution by charge injection from the Schottky barrier. Based on this, the residual electric charge removal method by heating and applied pulse voltage was developed. The development for practical use was studied of ultra-high sensitive photoelectric converters. As an intelligent photo sensor, a biomimetic visual photosensor was proposed which uses amplification/memory/arithmetic functions and film formation/processability of organic thin films. The paper also described the image sensor. (NEDO)

  6. FY1998 report on the surveys and studies on developing next generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For further resource and energy conservation and environmental load reduction, development is necessary on innovative chemical reaction technologies. This paper describes surveys on next generation chemical processes. As non-halogen processes subject to development of new catalysts, new processes were investigated and searching experiments and discussions were given on isocyanate, propylene oxide, and phenol. Technological progress in the C1 chemistry was investigated. Problems in hydrocarbon compound oxidation, hydroxylation, and decomposition by utilizing microorganisms were put into order as application of environmentally friendly technologies. Marine biotechnical possibilities were surveyed. The surveys were given on new processes utilizing the phase transfer catalyst forming a third phase, manufacture of biodegradable plastics, and a novel reaction system combined with self-separation process using molecular assembly. Possibilities were searched on designing a truly simple production system of highly energy saving type. Such fundamental common technologies as structure analysis, property control and reaction engineering were investigated for methods to manufacture functional micro-powder chemical materials. Development was discussed on a system for technology assessment over whole product life cycle to structure a technology assessment basis. (NEDO)

  7. Report on the achievements in fiscal 1999. Technology to use gas hydrate as a resource (Research and development for exploration, research and development on drilling technologies, investigative research on an environment influence evaluation method, and investigative research on a utilization system); 1999 nendo gas hydrate shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansa nado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The contents of the research and development performed in the current fiscal year are as follows: (1) research and development for exploration, (2) research and development on drilling technologies, (3) investigative research on an environment influence evaluation method, and (4) investigative research on a utilization system. In Item (1), element analysis data are used to study a method to estimate production environment of hydrate ore beds by using an inorganic ion analyzer and a trace amount element analyzer, the crust thermal flow measuring method is used to discuss a method to analyze the hydrate stability zones together with the data of sea area exploration records, and conceptual design is made on a resource potential evaluation system. In Item (2), experiments and analytical discussions are performed on decomposition control of the gas hydrate solid-liquid interface according to such conditions for the drilling fluid as temperatures and flow rates. Elucidation is given on the initial process of bubble generation for behavior of decomposed gas bubbles. Observation and elucidation are made on two-phase flow behavior of non-Newtonian fluid. In Item (3), conceptual design is carried out on a system to detect elements of shape change in each bed due to fluid movement in a gas hydrate bed and an upper bed. In Item (4), discussions are given on the optimizing conditions for generation and dissociation of gas hydrates. Investigation is made also on a possibility of the transportation and storage system. (NEDO)

  8. Report on the achievements in fiscal 1999 on research and development of a human cooperating and coexisting type robot system (Development of energy use rationalization technology); 1999 nendo ningen kyocho kyozongata robot system kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a system technology for the human cooperating and coexisting type robot that can perform various types of works substituting human hands. This paper summarizes the achievements in fiscal 1999. In developing a high-function hand, development and fabrication were executed on a device to teach four finger holding actions that correspond to the enhancement in action stability and control responsiveness of the four finger hand and to positions and attitudes of objects. In fabricating the robot platforms, single platform tests and remotely controlled platform connection tests were performed, which demonstrated the functions as an integrated system. In developing libraries for topography adaptive three-dimensional basic walking actions, development was carried out on libraries that correspond to menus for direct advance on a flat land, slewing, and walking on staircases and irregular land. It was found that control closer to that for actually usable robot is possible by considering time delay in articulate control when simulation was performed using the testing robot body. In the study and survey of robot proliferation, development plans were presented that take into consideration the social influence, technological factors, and cost need adaptability. (NEDO)

  9. Report on research achievements in fiscal 1999. Research and development of an ultra-high density electron SI technology (development of a technology for energy use rationalization); 1999 nendo chokomitsudo denshi SI gijutsu no kenkyu kaihatsu energy shiyo gorika gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    A high-density information network society is going to be realized in the 21st century. Information communication devices used therein are demanded of having high speed and high performance including acoustic and image digital processing, reduced size and weight, and low electric power consumption. While explosion in increase is estimated in the quantity of information handled by these information communication devices, there is a trend that the speed increase in CPU cannot follow the quantity increase. The present proposal is intended to make drastic performance enhancement by using the electron SI (comprehensive mounting) technology which includes making the LSI chips three dimensional and compounding light and electric power mounting, as well as design optimization. The present research and development has an objective to integrate the following three elements to achieve an ultra-high density electron SI technology: (1) a three-dimensional lamination technology making shortest wiring between LSI chips possible, (2) a light and electric power compounded mounting technology making high speed and large capacity transmission inside a board possible, and (3) optimal wiring structure design to suppress unnecessary electromagnetic radiation caused by increasing signal speeds. The research plan period lasts for five years. This paper reports the progresses in each theme in fiscal 1999. (NEDO)

  10. Fiscal 2000 achievement report. Development of prompt-effect technology for innovative energy environment (Research and development of extremely low power consuming LSI for information terminal); 2000 nendo sokkoteki kakushinteki energy kankyo gijutsu kaihatsu seika hokokusho. Gokuteidenryoku joho tanmatsuyo LSI no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the advancement of information technologies, multimedia information terminals such as handyphone systems and mobile computers are increasing in number and improving in quality, sharply increasing power consumption in this domain. So as to suppress the power consumption, efforts are exerted to develop technologies for information terminal LSI (large-scale integration) substrates consuming extremely low power and still capable of high-speed operation. Studied are a device technology of SOI (silicon on insulator) to realize a remarkable reduction in power consumption and enable high-speed operation and a circuit technology of the multi-threshold CMOS (complementary metal-oxide semiconductor) advantageous to the achievement of low-voltage high-speed operation. In concrete terms, the efforts center about an extremely thin film SOI device of the full depletion type higher in transistor driving capability, lower in load capacity, and smaller in surface area than those currently in use, and aim to put such an SOI device on an optimized multi-threshold CMOS circuit for the establishment of techniques toward the embodiment of an LSI substrate consuming extremely low electric power. (NEDO)

  11. Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzokukei)'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-31

    The results of the first phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to understanding the basic characteristics regarding wettability and reactivity of PAN-based carbon fibers and PCS-based silicon carbide fibers with metals, in which aluminum-based matrices are considered; preliminary tests for various composting methods; and development of wire preforms as the intermediate materials. Bright prospects have been obtained for improving problems involved in each technique. For development of molding/processing techniques, basic researches have been conducted for hot pressing/rolling, extrusion/withdrawal, powder molding and melt molding, using various reinforcing fibers. Bright prospects have been also obtained for combinations of adequate molding processes for individual materials. For development of design techniques, the basic data regarding mechanical characteristics of FRMs, both domestic and foreign, are collected, and analyzed by the trace tests with specimens, to set up the targets for FRM function improvements, viewed from the designs. (NEDO)

  12. 1998 Annual Study Report. Research and development of power storage by high-temperature superconducting flywheels (research and development of permanent magnet); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (eikyu jishaku no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    The permanent magnets have been investigated and developed, for eventual commercialization of a 10 MWh power storage system by high-temperature superconducting flywheel. The permanent magnet rotors have been already developed in the previous years using a praseodymium-based magnet (Pr magnet) and neodymium-based sintered magnet (Nd sintered magnet), and the target rotational speed of 30,000 rpm has been attained. For development of the magnetic circuit to produce a stronger and smoother magnetic field, magnetic flux density of the Nd sintered magnet is measured. It shows a lower magnetic flux irregularity than the Pd magnet, but there is still room for further improvement. For development of large-size permanent magnet fabrication techniques, it is confirmed that the large-size Nd sintered magnet can be easily magnetized by partial magnetizing, as is the case with the Pr magnet. In this year, the irregular magnetic flux is three-dimensionally simulated, based on the results obtained in the previous years, to find that the simulated results are in good agreement with the observed ones. The measures to solve the problems are also investigated. It is also confirmed that the large-size ring magnet can be easily magnetized by partial magnetization. (NEDO)

  13. FY 1999 Report on research and development of power storage by high-temperature superconducting flywheel. Research and development of permanent magnet; 1999 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu eikyu jishaku no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    The R and D program is implemented for permanent magnet, as part of the project aimed at commercialization of a 10 MWh-class high-temperature superconducting magnetic bearing type power storage system. A speed of rotation of 28,570 rpm is attained by using an iron intermediate ring for a Pr permanent magnet rotator and reinforcing the rotator with a plastic hoop reinforced with carbon fibers three-fold (CFPR hoop). The speed is increased to 31,300 rpm by interlacing carbon fibers also in the radial direction and replacing iron for the intermediate ring by titanium. The highest speed of rotation of 33,506 rpm is realized by the rotator of permanent magnet of sintered Nd. The magnetic circuit of stronger, more smooth magnetic field needs the permanent magnet of less uneven magnetic flux. The magnet is of a monoaxially anisotropic rare-earth metal, with four-fold magnetic ring bodies having fan-shaped small pieces arranged on each ring. Uneven magnetic flux occurs at the joint between these small pieces. The one-body-ring magnet of radially anisotropic, sintered Nd is developed, and incorporated in the repulsion type magnetic circuit, to reduce unevenness of the magnetic flux. (NEDO)

  14. Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

  15. Research and development of peripheral technology for photovoltaic power systems. Research and development of photovoltaic modules integrated with construction materials (detachable plane panel); Shuhen gijutsu no kenkyu kaihatsu. Kenzai ittaigata module no kenkyu kaihatsu (chakudatsushiki heiban panel)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of photovoltaic modules integrated with construction materials in fiscal 1994. (1) On development of technology for module structures, specifications of the horizontal muntin system module were newly determined in addition to the improved muntin system module, and the prototype pseudo-module integrated with construction material was prepared. The comparison results of the basic performance of both system modules clarified superior waterproofing and module temperature uniformity of the horizontal muntin system. Based on this specifications, integration technology of modules with back metal plates was studied. Formation of the integrated module close to final specifications was ascertained to be possible by use of passivation equipment to irregular form. (2) On development of construction and installation methods of modules, improvement of the waterproofing and workability of both system modules was studied. (3) On the study on practical use of modules, their design and ventilation/cooling structure were studied. 38 figs., 13 tabs.

  16. Research and development of the industrial basic technologies of the next generation, 'composite materials (resin-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (jushikei)'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-30

    The results of the first phase research and development project for developing the resin-based composite materials as the basic technologies of the next generation are evaluated. This project is aimed at development of the resin-based composite materials as light, high-strength and high-rigidity structural materials. Development of the basic techniques for these materials is of high significance, and highly rated. The first R and D phase efforts are directed to synthesis of new skeleton and terminal compounds, and their introduction into the matrices; application/combination of various fiber surface modification techniques; development of the basic techniques for intermediate materials for three-dimensional fabrics, triaxial fabrics and hybrid materials; improvement of the main techniques for a series of molding/processing steps; adoption of new methods; and development of design programs and elementary design techniques. The technical targets of improving functions of each item have been achieved, or bright prospects have been obtained therefor, each involving potentials of functional improvements by developing new functions. It is also considered that the parallel, competitive development and promotion of 7 routes in researches on the matrix resins have brought great effects. (NEDO)

  17. Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the second phase research and development; Jisedai sdangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzoukei)'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-31

    The results of the second phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to modification of PAN-based high-strength carbon fibers for aluminum-based FRMs, and also to development of the methods for controlling interfacial reactions at high temperature by modification of the base materials for titanium-based FRMs. For development of carbon fiber-based intermediate materials, the techniques are developed for continuous production of wire preforms of aluminum. For development of molding/processing techniques, the press molding and powder HIP molding techniques are developed to give a planar product of the FRM of titanium alloy reinforced with evaporated filaments of silicon carbide, which shows an average tensile strength exceeding the target level. Also developed are the press and roll molding techniques for the wire preforms of aluminum reinforced with silicon carbide fibers, the planar product therefrom showing a tensile strength of at least 99% of the base material. It is concluded that the objectives of the second-phase project are almost achieved. (NEDO)

  18. Annual Report (No. 2) of Center for Advanced Research of Energy Technology, Hokkaido University; Hokkaido Daigaku energy sentan kogaku kenkyu center nenpo dai 2 go

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Compiled into this report are the activities and achievements of the center in fiscal 1995. Under study in the field of carbonaceous resources conversion reaction are the high-molecular coagulation structure, pyrolysis and carbonization, ignition, complex conversion of resources together with other resources, etc. Under study in the field of carbonaceous resources assessment are catalytic chemistry, organic chemistry, physical chemistry, and analytical chemistry. Under study in the field of the control of energy conversion are the generation of high-temperature thermal energy and its conversion into electromagnetic energy. In the study of ultimate materials engineering, materials are studied for use under hostile conditions such as in a nuclear fusion reactor. As for papers published in fiscal 1995, there are 9 in the field of carbonaceous resources conversion reaction, 11 in the field of carbonaceous resources assessment, 7 in the field of energy conversion control, 10 in the field of ultimate materials engineering, and 4 in other fields. Published also are 9 articles covering general remarks, interpretations, and reviews. As for academic lectures, 13 are given in the field of carbonaceous resources conversion reaction, 14 in the field of carbonaceous resources assessment, 27 in the field of energy conversion control, and 39 in the field of ultimate materials engineering. (NEDO)

  19. Annual Report (No. 3) of Center for Advanced Research of Energy Technology, Hokkaido University; Hokkaido Daigaku energy sentan kogaku kenkyu center nenpo dai 3 go

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Compiled into this report are the activities and achievements of the center in fiscal 1996. Its studies in the field of carbonaceous resources conversion reaction involve the high-molecular coagulation structure, pyrolysis and carbonization, ignition, complex conversion of resources together with other resources, etc.Under study in the field of carbonaceous resources evaluation are catalytic chemistry, organic chemistry, physical chemistry, and analytical chemistry. Under study in the field of the control of energy conversion are the generation of high-temperature thermal energy and its conversion into electromagnetic energy. In the study of ultimate materials engineering, materials are studied for use under hostile conditions such as in a nuclear fusion reactor, atomic reactor, and combustion plasma. As for papers published in fiscal 1996, there are 19 in the field of carbonaceous resources conversion reaction, 17 in the field of carbonaceous resources assessment, 6 in the field of energy conversion control, and 26 in the field of ultimate materials engineering. Published also are 8 articles covering general remarks, interpretations, and reviews. As for academic lectures, 31 are given in the field of carbonaceous resources conversion reaction, 20 in the field of carbonaceous resources assessment, 30 in the field of energy conversion control, and 38 in the field of ultimate materials engineering. (NEDO)

  20. Annual Report (No. 4) of Center for Advanced Research of Energy Technology, Hokkaido University; Hokkaido Daigaku energy sentan kogaku kenkyu center nenpo dai 4 go

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Compiled into this report are the activities and achievements of the center in fiscal 1997. Under study in the field of carbonaceous resources conversion reaction are the high-molecular coagulation structure, pyrolysis and carbonization, ignition, complex conversion of resources together with other resources, etc. Under study in the field of carbonaceous resources assessment are catalytic chemistry, organic chemistry, physical chemistry, and analytical chemistry. Under study in the field of the control of energy conversion are the generation of high-temperature thermal energy and its conversion into electromagnetic energy. In the study of ultimate materials engineering, materials are studied for use under hostile conditions such as in a nuclear fusion reactor. As for papers published in fiscal 1997, there are 18 in the field of carbonaceous resources conversion reaction, 10 in the field of carbonaceous resources assessment, 13 in the field of energy conversion control, and 17 in the field of ultimate materials engineering. Published also are 10 articles covering general remarks, interpretations, and reviews. As for academic lectures, 26 are given in the field of carbonaceous resources conversion reaction, 13 in the field of carbonaceous resources assessment, 29 in the field of energy conversion control, and 45 in the field of ultimate materials engineering. (NEDO)

  1. Annual Report (No. 5) of Center for Advanced Research of Energy Technology, Hokkaido University; Hokkaido Daigaku energy sentan kogaku kenkyu center nenpo dai 5 go

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Compiled into this report are the activities and achievements of the center in fiscal 1998. Under study in the field of carbonaceous resources conversion reaction are the high-molecular coagulation structure, pyrolysis and carbonization, ignition, complex conversion of resources together with other resources, etc. Under study in the field of carbonaceous resources assessment are catalytic chemistry, organic chemistry, physical chemistry, and analytical chemistry. Under study in the field of the control of energy conversion are the generation of high-temperature thermal energy and its conversion into electromagnetic energy. In the study of ultimate materials engineering, materials are studied for use under hostile conditions such as in a nuclear fusion reactor. As for papers published in fiscal 1998, there are 24 in the field of carbonaceous resources conversion reaction, 8 in the field of carbonaceous resources assessment, 10 in the field of energy conversion control, and 17 in the field of ultimate materials engineering. Published also are 4 articles covering general remarks, interpretations, and reviews. As for academic lectures, 21 are given in the field of carbonaceous resources conversion reaction, 25 in the field of carbonaceous resources assessment, 23 in the field of energy conversion control, and 47 in the field of ultimate materials engineering. (NEDO)

  2. Development of small-size transmission tower erection method; Kogata tetto kumitate koho no kaihatsu kenkyu (gaibushiki crane ni yoru kogata tetto kumitate koho no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Matsuishi, S.; Asano, J.; Koji, Y. [Kansai Electric Power Co. Inc., Osaka (Japan); Tsujimura, I.; Teramoto, A. [The Kanden Kogyo Incorporated, Osaka (Japan); Sasaki, T.; Mito, K. [AG Ajikawa Corp., Osaka (Japan); Tsuji, M.; Fukumoto, T.; Yamaguchi, N.

    1997-09-30

    To reduce the construction period and cost and to enhance the safety during 77 kV-class transmission tower election, a new method of small steel transmission tower erection using an external type crane has been developed. For the selection of cranes, a commercially available self-climbing crane was employed which has an operating radius of 11 m, a lifting load capacity of 1.5 t, and a lift of up to 60 m. For the space analysis using a model tower, various supporting methods with horizontal supporting members, stress analysis for each tower stub, and apparatuses were examined. For the demonstration tests of election using the model tower, strain gages were attached at each point of steel tower, crane and horizontal supporting members, to measure the stress of members at each stage of the election. It was confirmed that there were no problems. For the election of actual steel tower, the practicality of this method was compared with that of conventional methods. The construction period was reduced in 20%, and the cost was reduced in 4%. The safety of this method was drastically enhanced due to the lack of moving on the tower and less manual operation. 9 figs., 1 tab.

  3. Fiscal 1980 Sunshine Project research report. Development of hydrothermal power plant (Development of binary cycle power plant). Supplement. Research on plant technology; 1980 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden palnt no kaihatsu bessatsu (plant gijutsu kenkyu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Research was made on new geothermal power plant technologies such as downhole pump and dual boiler for development of the 10MW class binary cycle power plant using geothermal energy. In heat cycle calculation of dual boilers, the cycle performance of a subcritical multi-stage evaporation cycle with R-114 heat medium was obtained through cycle calculation, heat conduction calculation and profitability calculation. The calculation result suggested possible considerable reduction of heat loss due to heat exchange at a preheater and evaporator, and considerable reduction of discharge loss of hot water by such multi-stage evaporation cycle. In American, every geothermal binary cycle power plant adopts pressurized heat exchange between hot water and heat medium by using downhole pumps, and pressurized reinjection of hot water into the ground. Since downhole pump itself not yet satisfies its requirements enough, it is said that Department of Energy is now under consideration on the future R and D. (NEDO)

  4. Achievement report for fiscal 1990 on research and development of high-efficiency molecule separating membrane materials; 1990 nendo kokoritsu kobunshi bunrimaku zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    In order to achieve high efficiency and energy conservation in the separation processes in the chemical industry, activities were performed to seek high-efficiency liquid separation films, gas separation films, and the related technologies that make possible separation, condensation, and refinement of substances that have consumed large amount of energy in the conventional separation processes (for example, water-alcohol, and rare gases), and substances difficult of separation and refinement because of resemblance in physical and chemical properties (for example, isomer mixed substances). For the gas separation films, research and development has been made on (1) high-order molecule recognizing films, (2) high-density metal complex fixing thin films, (3) high-functional complex films, and (4) re-activating oxygen condensation films. In (1), attempt was made on oxygen condensation by impregnating the carrier film with aqueous cobalt complex solution with regard to oxygen, for example. Research has been made on alcohol condensation film in the liquid selecting and separating films. Research and development has been made on fluororesin films for water/polar organics separation, (3) high-order structure control of water selective and permeating films, (4) water/acetic acid separating films, and (5) particle separation process utilizing liquid films. (NEDO)

  5. Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (total system); 1974 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Total system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    The current most important solar energy utilization fields are solar energy power generation (solar heat and photovoltaic power generation), and solar heat cooling and heating. A solar heat power system collects or stores solar thermal energy as energy source of power systems, and converts it to electric power through heat exchange systems. To establish such system, not only R and D on a collector, absorption capsule, storage unit and heat transfer unit, but also complete study on an optimum system configuration and environmental impact are necessary. A photovoltaic power system converts solar energy to electric power directly by photoelectric conversion device such solar cell. Except specific local uses, drastic cost reduction and improvement of a conversion efficiency (at present 12-15%) and life (several years) are necessary for solar cells. Although a lot of solar heat cooling and heating systems is in practical use in Japan, for its further diffusion an important research task is development of heat collector excellent in efficiency, cost, life and maintainability. (NEDO)

  6. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology - Separate volume: Collection of data of photovoltaic power generation systems); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu - Bessatsu: taiyoko hatsuden system data shu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the establishment of technologies for optimum designs and optimum operation for various types of photovoltaic power systems, data are compiled in this volume, collected from the field test facilities and residential photovoltaic power systems. Operating data and meteorological data from the field test facilities (interconnection system, independent system, and water pump system) are arranged as easy-to-use supplementary data to help studies in relation to the 'energy flow in the test field facility systems' which is in the fiscal 1999 achievement report. As for data collected from residential photovoltaic power systems, they are arranged as easy-to-use supplementary data to help studies in relation to the 'Data and evaluation of residential photovoltaic power systems' which again belongs in the fiscal 1999 achievement report. (NEDO)

  7. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

  8. FY1999 annual report on the research and development on practical industrial cogeneration technology; 1999 nendo sangyoyo cogeneration jitsuyo gijutsu kaihatsu kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The basic plan aims to quicken the practical application of the industrial HBGT (hybrid gas turbine) cogeneration technology and thereby to realize high-efficiency energy utilization for reduction in CO2 emission. For this purpose, a medium-scale HBGT, expected to be high in efficiency and low in polluting, and its components are subjected to assessment tests and endurance tests to prove that there are reliability and soundness in HBGT. Ceramic members are developed which are high in strength at elevated temperatures and in resistance to oxidation, and are subjected to assessment so that they will be further improved in reliability and durability. An HBGT is designed, fabricated, and operated. The engine system is tested for performance, and the performance is improved. It is put to a long-term operation, which is to confirm the presence of soundness and reliability in HBGT as an industrial cogeneration system. Industrial fields in which HBGT will be useful are selected and surveys are conducted to find out how it will function in such selected fields. Problems which HBGT will encounter upon practical application are extracted, and measures for solving them are clarified. Such an HBGT will have a shaft output of approximately 8,000kW, engine thermal efficiency of not less than 34%, and a turbine inlet temperature of approximately 1,250 degrees C. (NEDO)

  9. Fiscal 1999 survey report. Important regional technology research and development--Research and development of eco-tailored tribo-material creation process technology (Research and development of micrometer structured material creation process technology); Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu. Micrometer order de seigyosareta material sosei process gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Researches are conducted on the creation of sub-millimeter structured coatings for engine cylinders, valve seats, etc., for the extensive enhancement of performance of tribology-involved parts. In relation to the technology of high-energy pulse laser-aided fabrication of coatings, a coating manufacturing unit is designed and built, and experiments are conducted for the improvement of molten particle generation efficiency and for the formation of coatings by the adhesion of molten Fe and Mo particles onto a cast iron substrate. In the study of abrasion-proof internal surface treatment technology, various sprayed coatings are prepared and checked for the surface reforming effect of laser irradiation, which is for the identification of sprayed coatings which are fit for laser-aided composite surface treatment. In the study of the creation of self-heat generative compounds and the practical application of their bonding feature, the effect is examined of laser irradiation conditions on the hardness and other properties of the surface layer of a hot-pressed Fe{sub 3}Al body with its surface coarseness homogenized by machining. For the analysis of the mechanism of tribological characteristics, coatings are caused to rub against each other in engine oil. (NEDO)

  10. Annual Report (No. 1) of Center for Advanced Research of Energy Technology, Hokkaido University; Hokkaido Daigaku energy sentan kogaku kenkyu center nenpo dai 1 go

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The activities of the Center cover basic researches into chemistry, physics, and materials necessary for the development of technologies relating to high-efficiency conversion of coal-centered fossil fuel resources and to the security of new energy sources. Studies under way in the field of carbonaceous resources conversion reaction involve the process of transfer of heat and substance in the coal conversion reaction, behavior of short-life intermediate products, and the structure and physical properties of coal as a molecular solid or macromolecule. Studies being conducted in the field of carbonaceous resources assessment include the search for and development of high-efficiency catalysts for coal conversion reaction systems, elucidation of physical and chemical structures of coal and coal-derived oils, energy conversion of the low-entropy type, creation of carbon-based functional materials, etc. Furthermore, research and development is under way for enhanced-efficiency conversion of high-temperature thermal energy acquired by fossil fuel combustion into electrical energy and for materials that will constitute nuclear fusion reactors and atomic reactors and will withstand combustion plasma. (NEDO)

  11. Survey and research on patent and information. Survey of standard terms (Hydrogen energy); Kijun yogo chosa tokkyo joho chosa kenkyu. Suiso energy (kento shiryo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Collected in this glossary are terms for use in the development of hydrogen energy technologies. This glossary has been compiled, in view of the current situation where terms are used without standardization or distinction in various recent reports and publications relating to the development of hydrogen energy technologies, to prevent confusion and to help enhance research and development under the Sunshine Program. This is a 3-year endeavor that was started in 1979, undertaken by a committee consisting mainly of men of learning and experience representing organizations associated with the Sunshine Program. The terms are collected from research achievement reports and other materials covering the period of fiscal 1974-1979 relating to hydrogen energy projects under the Sunshine Program. Approximately 200 terms were picked up in the first fiscal year, and 85 in the second fiscal year. Attached to each of the Japanese terms are the pronunciation, a corresponding English term, and a brief explanation in the Japanese language. (NEDO)

  12. Report on surveys in fiscal 1999 on research and development of the environment harmonizing catalyst technology; 1999 nendo kankyo chowagata shokubai gijutsu no kenkyu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the surveys in fiscal 1999 on research and development of the environment harmonizing catalyst technology. The discussion subjects taken up included suppression of discharge of carbon dioxide, catalysts used when manufacturing hydrogen and technology thereof, and environment purifying catalysts to decompose harmful substances, and technology thereof. The roles of catalysts and their technologies are expected in reducing the reforming temperatures, achieving energy saving, and reducing decomposition energy. Furthermore, the catalysts are expected of high activity, long life and low cost. Three themes were selected from the emergency and importance points of view. The themes are, in the consumer field, research and development of efficiency improvement in membrane reactors for reforming low-grade hydrocarbons to structure a technology to manufacture hydrogen for small-size portable fuel cells; and in the industrial field, development of hydrogen and carbon product manufacturing technologies with which CO2 generation is suppressed by means of the catalytic decomposition process. In practice, for such discharged harmful substances as dioxins, PCB and volatile organic compounds (VOC), treating them is the urgent environmental problem, and therefore, the fundamental research was taken up for practical application of the second-generation catalysts of the ultra-violet light and visible light responding type. (NEDO)

  13. FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. R and D of the photovoltaic power generation utilization system/periphery technology (R and D of the new solar cell module integrated with construction materials - Investigative study on analysis for commercialization); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system, shuhen gijutsu no kenkyu kaihatsu (Shinkenzai ittaigata taiyodenchi mojuru no kenkyu kaihatsu - Jitsuyoka kaiseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of supporting the study for commercialization of the new module integrated with construction materials, survey of the technical trend of the new module integrated with construction materials in Japan and abroad was conducted, and the FY 2000 results were summarized. As to the module material correspondent to construction materials, the results of the survey made in the past three years were summarized, and the subjects to be considered in future were arranged from a viewpoint of disposal/recycle of modules. Concerning the marketability, various policies for the spread of solar cell module that is an immature good were arranged. Survey was also made of the photovoltaic power system using the field test project as a sample, and the following were made clear: The photovoltaic power generation has appeal for environmental consideration and energy conservation; In some cases, the power generation effect was not as much as expected because the information on design/construction is not sufficient. Relating to the evaluation of its effect on the environment, the paper summarized the environmental influence in each of the module methods at each stage of production/utilization/disposal and the basic items for measures to cope with the influence. (NEDO)

  14. Current state of micro machine technologies and summary of its research and development. ; Research and development of the project requiring coordination among industries, government and universities, and international cooperation. Micro machine gijutsu no genjo to kenkyu kaihatsu no gaiyo. ; Hon project no kenkyu kaihatsu ni wa sankangaku no renkei to kokusai kyoryoku ga juyo

    Energy Technology Data Exchange (ETDEWEB)

    Konaka, M [Agency of Industrial Science and Technology, Tokyo (Japan)

    1991-11-15

    A summary is given on the current state of micro machine (MM) technologies and its research and development. The large scale project system was inaugurated in 1966 under the coordinations among the industries, government and universities. The MM technology creates micro movement mechanisms using IC{prime}s in place of electronic circuits. The subject is to perform an IC manufacturing process which can process IC{prime}s three-dimensionally and assemble them simultaneously, and the product strength. The target is a systematization of constitutive elements ultra small, yet high in performance. This requires an international cooperation. The future MM image would include those that enter blood vessels and organs to help operations with only a small amount of incision, and those that enter power plant boiler piping and aircraft engines to perform inspection and repair without a need of dismantling. Problems to be solved relate to the MM movement mechanisms, modules having environment recognizing function, small-size energy converters, wireless transmission technologies, and dynamics in microscopic regions.

  15. FY 1994 Report on the technical results. Research and development of micromachine technologies (Development of highly functional maintenance technologies for power plants); 1994 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    This research and development project is aimed at development of the technologies for the micromachines provided with maintenance functions, e.g., for examination and maintenance of abnormal conditions in heat exchangers, piping systems or the like. The initial target is set at establishment of basic technologies for the micromachines, in consideration of the available technologies. The R and D activities are directed to (1) microcapsules for, e.g., micro power generators, (2) mother machines having controlling and instructing functions, (3) non-cabled examination modules, (4) cabled examination modules, and (5) total systems. The item (1) involves the micro power generators, and mechanisms of signal transmission, flaw finding and driving/suspension; the item (2) mechanisms of micro-optics and connection, group controlling, microbatteries, action type controlling, and artificial muscles; the item (3) expansion/contraction type transfer mechanisms, light energy supply, micro visual sensation, function connection, and concerted controlling; the item (4) tubular manipulators, and mechanisms of light-aided power generation and voltage elevation; and the item (5) maintenance and micromachine systems. (NEDO)

  16. Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cells); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-27

    This report summarizes the fiscal 1974 research result on R and D of new type solar cells, which includes researches on (1) solar cell structure, (2) packaging, and (3) improvement of a conversion efficiency. In the 1st research, theoretical study was made on the relation between a solar cell efficiency and various design factors to obtain basic data for ordinary cell structure and vertical junction type cell structure. As impurity source, a thermal diffusion method using doped oxide by CVD was compared with that using boron nitride, resulting in no difference in solar cell characteristics between both methods. The measurement results on contact resistances of Al, Fe and Ni with electrodes prepared by electron beam deposition showed that these materials are applicable to Si more than 10{sup 18}/cm{sup 3} in impurity density as electrode materials. In the 2nd research, exposure tests were made on some kinds of specimens, resulting in no troubles. Study was made on production costs and structures suitable for automatic production of 4 kinds of packages with different basic structures. In the 3rd research, the prototype solar cell was prepared to use under solar radiation within 20SUNS. (NEDO)

  17. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  18. Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

  19. Fiscal 1976 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cell); 1976 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-05-30

    This report describes the fiscal 1976 research result on new type solar cells for photovoltaic power systems. On junction formation, the solar cell fabricated by spray coating showed output characteristics equivalent to that by rotary coating or phase diffusion, and inexpensive coating liquid, 1/40 of commercially available liquid in price, showed a sufficient result, however, the conversion efficiency of P{sup +}/N elements was insufficient. Schottky barrier polycrystal Si thin film was suitable for large-area elements without any property degradation. Small grain boundary density of polycrystal layers was also necessary. Temperature characteristics of collector element structure with a comb electrode were calculated theoretically. Change in diffusion length of minority carriers due to temperature well agreed between measured and calculated ones. Optimization calculation was also carried out. The size, curve, weight and transmissivity of plastic and glass materials for solar cell packaging were evaluated by continuous outdoor exposure tests. Fluorinated ethylene-propylene, methyl methacrylate and polycarbonate plates and glass were the most promising materials because of less deformation. (NEDO)

  20. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  1. Research and development of evaluation system for photovoltaic power generation system. Research and survey on test and evaluation method for BOS component devices; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Shuhen gijutsu hyoka system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of the evaluation method for BOS component devices in fiscal 1994. (1) On the study on requirements of BOS component devices for practical use, the study results on storage battery, inverter, protective device for system interconnection, and effective use means for storage battery were summarized. On the future device technology, it was clarified that the following value added technologies are promising: simple design of inverter circuit, cost reduction by common specification and mass production, and stabilization of voltage and compensation of momentary peak load by combining inverter with small-capacity storage batteries. (2) On the study on the performance test method for BOS component devices, basic characteristic (capacity, efficiency) test, PSOC charge/discharge cycle test, and accelerated life cycle test were performed for 4 kinds of new storage batteries developed by NEDO. The whole characteristic test results satisfied specifications, and long-term cycle test is in promotion for all new storage batteries. 3 figs., 4 tabs.

  2. Survey of the actual state of the coal related research and development in Japan. 11; Nippon ni okeru sekitan kanren kenkyu kaihatsu jittai chosa. 11

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    NEDO is surveying the actual state of the coal related research/development in Japan to supply information on the coal related research/development in Japan to IEA`s coal research project database. This book of fiscal 1997 version includes 338 subjects. The details described are name of research institute, the section in charge, address, name of country, telephone No., name of joint researcher, research theme, classification, outline of research, project No., name of researcher, sponsor, the budget appropriated, term of research, remarks, etc. The books of data collected from each country in surveys of the actual state of the coal related R and D and IEA`s coal researches which have been made so far are submitted for general viewing at NEDO Information Center. Also, a part of those can be accessible from the energy database of which NEDO Information Center is performing on-line service for user members

  3. FY 2000 report on the survey to support the R and D on the development of the coal/natural gas use CO2 recovery/utilization technology; 2000 nendo sekitan tennen gas katsuyogata nisanka tanso kaishu riyo gijutsu no kaihatsu ni kansuru kenkyu kaihatsu shien chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this study, technology to rationalize energy utilization is developed by which CO2 is efficiently converted into methanol which is the next generation liquid fuel by reacting CO2 with coal, natural gas and steam using solar heat. Together with this study, survey/study are conducted of the trend of the related element technology and the total system technology, trend of the competitive technology, study of comparison with the competitive technology, economical efficiency, possibility of the commercialization, etc. In this report, in Chapter 1, summarized are the trend of the R and D which each country conducts with the aim of using abundant solar energy in the Sun Belt and the trend of other R and D of energy utilization in each country. In Chapter 2, the paper describes the technology that Japan is now developing and the developmental trend of the related technology. In Chapter 3, the methanol supply/demand balance and the related researches were arranged. The most important points in future commercialization of the said technology are the establishment of technology and the economical efficiency. (NEDO)

  4. Fiscal 1991 research report. Research trend survey for next-generation industrial structure technology research and development project - Research and development of advanced materials for extreme environments; 1991 nendo jisedai sangyo kiban gijutsu kenkyu kaihatsu project ni kakawaru kenkyu doko chosa hokokusho. Chotaikankyosei senshin zairyo no kenkyu kaihatsu (sekitoku daiene)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Efforts were exerted to develop intermetallic compounds and C/C (carbon/carbon) composites to serve as advanced materials for extreme environments. In relation with advanced materials, especially with intermetallic compounds and fiber reinforced intermetallic compound composite materials, a technical research survey was conducted covering the three fields of (1) summarization of activities conducted up to fiscal 1991, (2) contents of associated aerospace projects, and (3) aeroengine components. In Field (1), the ground on which the project was created and the project's basic plans, goals, and systems, and its ripple effects are discussed, and the fruits produced so far are summarized. In Field (2), aeroengine component related projects of America, Britain, France, Germany, and Japan are investigated. In Field (3), aluminum alloys, titanium alloys, alloy steel, superalloys, intermetallic compounds, and intermetallic compound composite materials are discussed with attention paid to their current status and future trend, characteristics they are supposed to finally assume, and technical tasks to discharge for the development of technologies concerned. (NEDO)

  5. Fiscal 1991 research report. Research trend survey for next-generation industrial structure technology research and development project - Research and development of advanced materials for extreme environments; 1991 nendo jisedai sangyo kiban gijutsu kenkyu kaihatsu project ni kakawaru kenkyu doko chosa hokokusho. Chotaikankyosei senshin zairyo no kenkyu kaihatsu (sekitoku sekiyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Efforts were exerted to develop intermetallic compounds and advanced C/C (carbon/carbon) composite materials usable under extreme environments such as high temperatures. In relation with advanced composite materials, especially with projects for developing composite materials using oil as raw material, a survey was conducted of the three fields of (1) summarization of activities conducted up to fiscal 1991, (2) contents of associated aerospace projects, and (3) oil based composite material technology. In Field (1), past achievements are summarized. In Field (2), aerospace projects under way across the world are broken down by airframe and engine, and are reviewed from the viewpoint of needs for materials. In Field (3), the present and future of heat resisting thermosetting composite materials, thermoplastic composite materials, and C/C composites are discussed. Characteristics such materials are supposed to finally assume and tasks to discharge for technical development are also taken up. (NEDO)

  6. Achievement report for fiscal 1981 on Sunshine Program-entrusted research and development. Research on hydrogen energy total system; 1981 nendo suiso energy total system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In this research, studies are conducted relative to the time point, form, and magnitude of the introduction of hydrogen into Japan's total energy system. The research aims to construct a hydrogen energy total system consisting of hydrogen energy subsystems to be available in the future and to clearly define the stage at which transfer to the target system will be carried out. In the research for fiscal 1981, studies continue about the feasibility of hydrogen as automobile and aviation fuels and as a material for use in chemical engineering, about conversion into each other of hydrogen and various synthetic fuels and electric power with which hydrogen will have to compete in the domain into which it will be supplied, and about technologies of their utilization for comparison between such energies in the search for their interchangeability. Surveys are conducted on technical data about local energies. The Yakushima island is chosen, for instance, and a conceptual hydrogen energy base is constructed there and the cost for the construction is estimated. At the last part, the feasibility of the introduction of hydrogen into Japan's energy system in the future is discussed for assessment. (NEDO)

  7. Research and development cooperation project on environmental measurement using laser radar in fiscal 1995; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of contributing to the environmental management in Indonesia, Japan made R and D of a laser radar to measure the urban air pollution and an environmental network jointly with Indonesia in compliance with the actual situation of the country. At present, in developing countries, air pollution is becoming a big problem because of increases in population and in energy consumption in urban areas according to the industrial/economic growth. As for the laser radar, it is an active sensor with laser as light source and can observe in high resolution the three-dimensional space distribution such as density and composition of air pollutants. Japan is a leader in the development of laser technology which is a core technology for the laser radar and the preceding research. The equipment is installed at several points of urban areas in Indonesia, and at the same time, the observation network is constructed to collect, analyze and process data at the central processing center. This is a 4-year plan from fiscal 1993 to 1996. In fiscal 1995, negotiations with Indonesia and field surveys were conducted to determine sites for installation. A plan for system improvement was also decided on. 38 refs., 24 figs., 14 tabs.

  8. Fiscal 2000 survey report. Survey report on development and utilization of alternative energies for oil in Pacific region; 2000 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted, with environmental matters taken into consideration, for building an information gathering infrastructure for the countries in the Pacific region, capable of promptly and accurately collecting and offering energy related information. Conducted in this fiscal year were regular data gathering, review of oil supply and demand and alternative energy supply and demand in the Pacific region, on-site survey of alternative energy development and utilization in Vietnam, quarterly analyses of trend of energy demand, and the like. The supply of primary energy in the Pacific region increased by 2.3% per year in the period 1980 through 1998. The rate of increase was the lowest with oil, and the highest with hydroelectricity, atomic power, and recoverable energies such as geothermal energy. The Vietnamese Government is promoting its efforts to develop power sources by use of recoverable energies for farm village electrification. Efforts are being earnestly exerted to develop its rich natural gas resources and it is expected that there will be a remarkable achievement in the use of alternative energies due to an increase in natural gas consumption. In the field of data collection, various data were registered with the database. (NEDO)

  9. Research and development of cooled turbine for aircraft engines. Koku engine yo reikyaku turbine no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Maya, T; Yamawaki, S [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    For the turbine which is one of the principal elements of aircraft engine, progress in turbine use material development and cooling performance further heightened for the turbine are needed to grapple with the required heightening of turbine inlet temperature. In the present paper based on the turbine inlet temperature designed to be 1600[degree]C as a target, a two-dimensional model used for the turbine cooling performance test was structurally given together with the result of the above test which aimed at confirming the design calculation. As a result of cooling design for the turbine which was about 1600[degree]C in inlet temperature, the highest gas temperature was 1890 and 1470[degree]C on the stator blade and rotor blade, respectively. Both those blades were 0.66 and 0.62, respectively in cooling efficiency. To test the cooling performance, a two-dimensional cascade was tested with a doubly amplified model of cooling blade, the use of which could set its Reynolds number near that of the actual one. As compared with the actual operation, the test was made at low temperatures of 400 to 500[degree]C and low pressures of 0.02 to 0.03MPa. The test agreed with the design calculation in result. 4 refs., 8 figs.

  10. FY1995 basic research for neuroactive materials; 1995 nendo shinkei kino zairyo kaihatsu ni kansuru kiban kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Development of nenroactive materials to improve neuronal defects is one of the most important subjects in Japan that will soon become a aging society. In this project, basic research for neuroactive molecule was performed to develop technology for neuronal regeneration, regulation of synaptic activity and interface between artificial surface and living neurons. A novel neurite promoting factor was discovered and its cDNA was cloned. Mutagenesis in vitro showed that a functional region of this factor located in a polypeptide of less than 50 aminoacids. Using neuronal culture, synapse formation was found to depend on two modes of activities and long-lasting synaptic potentiation was demonstrated to depend on a macromolecules released from pre- or postsynaptic neurons. To regulate nervous activities, photoactivated caged-peptide was developed and confirmed to change in affinity to its receptor. Neurons were cultured on substrates paterned by microlithography. (NEDO)

  11. Achievement report for fiscal 1997 on the research and development to lead to gas hydrate using technology. Research and development on exploration, research and development on drilling technologies, survey and research on a method to evaluate environmental impact, and survey and research on a utilization system; 1997 nendo gas haidoreto shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    The present study is intended to analyze comprehensively geophysical, geological and geochemical data, and establish a technology to estimate distribution of gas hydrate (GH) in sea areas around Japan. It is also intended to develop a high-accuracy resource amount calculating method utilizing the result of excavation of GH planned in the future. In order to achieve these goals, the following activities are performed: (1) study on a method to estimate production environment of GH deposits, (2) development of a method to estimate GH stability areas by using the crust thermal flow measuring method, and (3) study on estimation of GH distribution and wide-area potential. For the study (1), an inorganic element analyzer was introduced, and calibration of devices was performed in fiscal 1997. A survey was carried out on literatures related to distribution of inorganic elements and process of GH deposit production. In the study (2), design and trial fabrication were executed on a high-accuracy crust thermal flow measuring device, capable of long-term continuous observation. In the study (3), re-processing focusing on BSR was implemented by using the latest computer and analysis software on the data in which BSR has been confirmed in the surveys done in the past on sea areas around Japan. (NEDO)

  12. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

  13. Fiscal 1997 report under consignment from NEDO on the R and D of femto-second technology (development of ultra short pulse optoelectronics technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku femto gyo technology no kenkyu kaihatsu (chotan pulse ko electronics gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Very high speed electronics technology is indispensable for the creation of industrial base technology which supports high grade informatizing in the 21st century. The state of light and electronics is controlled in the femto-second time domain. As to the development of femto-second light pulse generation/transmission technology, mode synchronous semiconductor laser was manufactured using the strain quantum well structure aiming at heightening profit, and the repeated frequency, 166GHz, was achieved. Relating to the pulse compression element, exciton photonic band was newly designed. A technology of coding was also studied. As to the development of technology of femto-second light pulse control/distribution, shortening of the wavelength down to 1.5{mu}m and a possibility of femto-second domain high speed response were indicated by the combined double quantum well structure. The quantitative measurement of spin relaxation characteristics was successfully made. By the Mach-Zehnder light switch, obtained was the world`s fastest light switching characteristic. To realize the femto-second class very high speed element, conditions were grasped on the crystal growth of Sb based ultra thin films operating in the 1.5{mu}m zone by studying the quantum well using transition among sub-bands. 242 refs., 280 figs., 12 tabs.

  14. Study of highly efficient power generation system based on chemical-looping combustion; Chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, S; Suzuki, T; Yamamoto, M [Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Resources Utilization

    1997-02-01

    This paper describes the research and development of power generation system by means of chemical-looping combustion. For this system, fuel flows in a reduction reactor and air flows in an oxidation reactor. These two flows are separated. As a result, recovery of CO2 without energy consumption, drastic improvement of power generation efficiency, and suppression of NOx emission are expected. To realize the above, two promising candidates, NiCoO2/YSZ and NiO2/NiAl2O4, have been found as recycle solid particles between the both reactors. These have excellent oxidation/reduction cycle characteristics. By these particles as well as the existing particle, NiO/YSZ, practical application of the chemical-looping combustion is realized. Besides LNG, coal and hydrogen were considered as fuels. When using coal or hydrogen, it was found that temperature of the reduction reactor should be increased the same as that of the oxidation reactor. This is a different point from a case using LNG as a fuel. 5 refs., 2 figs.

  15. Report on current status of petroleum substituting energy development in the UK in FY 1997; 1997 nendo chosa hokokusho (sekiyu daitai energy kaihatsu no genjo (Eikoku))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Blair`s cabinet of the UK, as soon as it was formed, started a review of all policies of the past Conservative government, including the area of energy and environment. The Labour Party has already underlined its commitment to promoting petroleum substituting, i.e., renewable energy. The government made clear that the unique British NFFO Scheme to promote sources of renewable energy would continue and in November, 1997 published the policy guide for the fifth round of NFFO bidding. The British energy market is generally considered to be the most liberalized for free competition in Europe and even the retail market for households is going to be completely open for competition in electricity and gas supply by 1998. As to the regulation of the green house gas exhaust, the Labour Party has put forward a target to cut 20% of the exhaust level of 1990 by the year 2010. The government is now preparing measures for its implementation. At present, the EU is debating the draft of the landfill directive. In the UK, the construction of waste incineration and power generating plants with modern technology is now being promoted. 27 tabs.

  16. Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-30

    The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

  17. R and D project for large industrial technologies in fiscal 1989. Report on achievements in R and D of robots for critical works; 1989 nendo seika hokokusho. Ogata kogyo gijutsu kenkyu kaihatsu jigyo. Kyokugen sagyo robot no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    Research and development have been performed on basic technologies common to different types of robots to carry out works in critical conditions. This paper summarizes the achievements in fiscal 1989. In the R and D of sensor technologies, a prototype tri-axial one-millimeter sensor array and a signal processing device were produced and evaluations were given. A prototype production and evaluations were made on a system that can recognize comprehensively the slip, hardness, and moment as the tri-axial tactile information. In the R and D of motive force technologies, discussions were given on improvement of sensitivity of the torque sensor in the actuator for force control. Design and prototype fabrication were carried out on a speed reducer integrated actuator having a torque sensor for the manipulator's elbow joint. In addition, a force controlled controller was fabricated on a trial basis, which compensates the non-linearity of the force controlled actuator by means of software control. In the R and D of the robot languages, an application program was prepared on a representative work related to movements of a critical work robot. Verification was also conducted on the reasonability of the grammar specifications. (NEDO)

  18. Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-30

    The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

  19. FY 1999 Report on research and development of power generation by solid electrolyte fuel cell. Research and development of solid electrolyte fuel cell; 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    This project is aimed at establishment of the module basic technology and commercialization of the solid electrolyte fuel cell in the early stage by designing, construction, operation and performance evaluation of a several kW-class module which incorporates the cylindrical cell fabricated by the wet process. The FY 1999 R and D efforts include (1) cell performance demonstration study: the cylindrical single cell fabricated by the wet process is demonstration-tested to determine the initial performance and durability for continuous operation, thereby comparing the external reforming with internal reforming in output, with the internal reforming rate as the parameter, (2) development of a several kW-class module: the adequate cell arrangement structure within the module is studied by the computer-aided simulation, and the tests for confirming thermal cycle durability of the modified bundle are conducted using the module power generation unit and the several kW-class module is tested, and (3) development of the technology for designing a thermally supported module: the effects of, e.g., air and fuel supply conditions on the module performance are analyzed using the analytical model as the base. Expansion of the module level to the process simulation model has been completed, based on these results. (NEDO)

  20. Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

  1. 1998 Annual Study Report. Research and development of power storage by high-temperature superconducting flywheels. Research and development of high-temperature superconducting materials; 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (koon chodendozai no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This R and D program is aimed at optimization of superconductors for improved levitation force of the superconducting magnetic bearings which support a 10 MWh power storage system by high-temperature superconducting flywheel (FW), to clarify possibility of sizing up the FW body and R and D themes for the commercialization. The processes are screened to simultaneously solve the conflicting targets of sizing up the sample of the Y-based bulk superconducting material and improved crystal orientation of the whole bearing, leading to selection of multi-seeding. The sample made on a trial basis improves levitation force by approximately 30%. It is considered that the OCMG-processed rare-earth-based superconducting material can generate very strong electromagnetic force, when combined with a permanent magnet. The Ag-doped Sm-based bulk material shows a reduced creep-caused loss of loading force, and a lower loss of Jc resulting from increased temperature than the Y-based one, decreasing AC loss and controlling temperature rise. The running characteristics and mechanical strength of the FW, and causes for temporal changes are investigated, in order to evaluate the superconducting material characteristics. (NEDO)

  2. Research and development of peripheral technology for photovoltaic power systems. Development of inverter technology for photovoltaic (PV) system which is connected to the utility grid; Shuhen gijutsu no kenkyu kaihatsu. Fukusu kino tan`itsuka shuhen sochi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on development of integrated multifunctional peripheral equipment in fiscal 1994. (1) On development of inverters with no transformer, the following study results were obtained. Converter efficiency reached the target of 95.0% by using an improved general purpose IGBT as switching element of main circuit. Distortion factor of output current harmonics achieved 5% in total current distortion factor, and less than 3% in each order harmonic current one. In control of the DC part of output current, the target less than 0.3% was achieved by inserting a capacitor into detection signal circuit and by detection/correction control of current detector offset. Detection level of 100mA was achieved for DC grounding detection by installing a DC grounding detector in the DC input side of inverters. VCCI 1 level was also achieved for EMI measurement. (2) On development of integrated multifunctional peripheral equipment, evaluation test of the prototype equipment of 0.025m{sup 3} in volume and 17kg in mass was carried out. 3 figs., 1 tab.

  3. R and D project for large industrial technologies in fiscal 1990. Report on achievements in R and D of robots for critical works; 1990 nendo seika hokokusho. Ogata kogyo gijutsu kenkyu kaihatsu jigyo. Kyokugen sagyo robot no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-01-01

    Research and development have been performed on basic technologies common to different types of robots to carry out works in critical conditions. This paper summarizes the achievements in fiscal 1990. In the R and D of tactile sensors, a prototype multi-element sensor array applicable to fingers of a robot hand was produced, and the characteristics test was conducted. In the R and D of motive force technologies, a force controlled actuator for wrist containing a torque sensor was designed and produced on a trial basis, whereas evaluations were given on the size and weight reduction and the force control performance. Regarding the actuator with redundant degree of freedom, a force controlled arm was attached with an actuator with three degrees of freedom to have performed an evaluation experiment. With regard to a small size and light weight controller, fabrication was carried out on a multi-function, high-density controller which adds positional control and peripheral interface functions to the force controlling function, and an evaluation was given. In the R and D of robot language, discussions were given on robot languages related to each system of movement, manipulation, and sensors, and the grammar specifications were prepared. (NEDO)

  4. Achievement report for fiscal 1998. Research and development of synergy ceramics (Research and development of anti-corrosion technologies for oil production system); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A computer simulation-aided designing technology is completed to help develop synergy ceramics which are complicated in phase constitution and material structure. A program, which simulates sintering and particle growth for multiple solid-state and solid-state/liquid-phase systems, has been built assuming the form of an integrated micro/nano level simulation technology based on the Monte Carlo method. The new program applies to systems consisting of more than three different phases, and deals in a uniform way with the designing of various textures formable by transfer of matters in solid-state particle growth, Ostwalt ripening, solid-state sintering, liquid-phase sintering, and additive reaction. The Monte Carlo method-assisted program is applied to systems based on AlN, Si{sub 3}N{sub 4}, and Al{sub 2}O{sub 3}, and a good result is achieved in each case. The molecular dynamic method is mainly used in atom level simulation for application to ZrO{sub 2}-Y{sub 2}O{sub 3} and Si-C-N, and a good result is achieved in each case. (NEDO)

  5. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  6. FY 1991 Research and development project for large-scale industrial technologies. Report on results of R and D of superhigh technological machining systems; 1991 nendo chosentan kako system no kenkyu kaihatsu seika hokokusho. Chosentan kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Described herein are the FY 1991 results of the R and D project aimed at establishment of superprecision machining technologies for developing machining technologies and nano-technologies aided by excited beams. The researches on the superprecision machining technologies involve design and development, on a trial basis, of the totally static pressure type positioning device, for which automatically controlling drawing is adopted to improve its rigidity. The researches on the surface modification technologies aided by ion beams involve scanning the ion beams onto the metallic plate to be provided around the glass substrate. The results indicate that the secondary electrons generated can be used to control charge-up. In addition, part of a 30cm square glass substrate is modified by implantation of the spot type ions of high current density, and the modified portion is used to produce a thin-film silicon transistor. The researches on superhigh-technological machining standard measurement involve improvement of precision of the system aided by a dye laser, which attains a precision of 0 to 30nm in a 0.1m measurement range. (NEDO)

  7. Hydrogen utilization international clean energy system technology (WE-NET). Subtask 8. Research and development of hydrogen combustion turbines (development of ultra-high temperature materials); Suiso riyo kokusai clean energy system (WE-NET). Subtask 8. Suiso nensho turbine no kenkyu kaihatsu chokoon zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper described the result of the fiscal 1996 development of ultra-high temperature materials for parts of hydrogen combustion turbines, as part of the hydrogen utilization technology, which have excellent environmental protectivity and remarkably high efficiency. By the optimized solution heat treatment of monocrystal alloy developed in the previous fiscal year, obtained was strength property the same as the existing super alloys. As to FRC, pore size and strength property of SiC organic hybrid were made clear. ODS alloy cooling blades and heat insulation coating were studied, and YSZ was found to be most excellent as coating material. Concerning intermetallic compounds, the applicability to ultra-high temperatures up to 1700degC was not obtained. For improvement of heat resistance and environment resistance, adopted were highly compacting SiC matrix and BN coatings. Al2O3 was excellent in long-time stability. In the 1600degC steam corrosion test on multiplex structural materials with Al2O3 as surface material, chemical stability was confirmed. Three-dimensional woven fiber reinforced composite materials of C/C{center_dot}CMC were trially produced by changing the fiber orientation, and improvement in ultra-high temperature thermal shock resistance was confirmed. A study was made of spot observation of the specimen surface by laser microscope, and development was conducted of a temperature measuring method with no influence of radiant heat. 44 refs., 250 figs., 40 tabs.

  8. FY 1999 report on the result for research and development of instantaneously effective and innovative energy and environment technology. Development of technology to use combustible wastes as resources and fuels; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu kanengomi saishigen nenryoka gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Manufacturing compressed fuel, or refuse paper and plastic fuel (RPF) from combustible wastes such as used papers and waste plastics to utilize them effectively as a fuel to substitute fossil fuels is regarded as a promising engagement. However, this process indispensably requires removal of chlorine contained in used papers and waste plastics to a degree that they do not impede the combustion. The present research and development is intended to develop a PRF pretreatment technology and a dechlorination technology, and establish a technology to utilize the materials as resources and fuels as thermal recycling of combustible wastes. The current fiscal year has performed research and development on the following themes: development of a sorting system and a crushing system in developing the pretreatment technology, whereas for the former system, sorting tests were carried out by using a vibration type wind power sorting machine and an inertia force wind power sorting machine, and for the latter system, data were obtained on the crushing characteristics; dechlorination tests, in which it was discovered that the mixing ratio of used paper in the material affects the chlorine concentration; research on combustion characteristics, in which fundamental combustion tests using a small fluidized bed, combustion tests using a bench scale fluidized bed, and stoker fired furnace combustion tests were performed; and demonstrative operation researches. (NEDO)

  9. Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 10. Development of low-temperature materials; 1999 nendo suiso riyo kokusai clean energy gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 10. Teion zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on material property test under liquid hydrogen environment, and development of optimum welding material and welding technique for the WE-NET plan. In the study on material properties in a liquid hydrogen temperature range, fatigue strength tests of base metals and weld metals were conducted under liquid hydrogen environment continuously, and further fatigue data were collected. As a result, it was clarified that both SUS304L and SUS316L have extremely high fatigue strength. To improve the tenacity of candidate weld metals under liquid hydrogen environment, material tests of welds were conducted on the laser-welded stainless steel joint and friction stir- welded Al alloy joint prepared by TWI (The Welding Institute) in the U.K. The laser-welded stainless steel joint showed higher low-temperature tenacity and lower ductility than TIG- welded joints. The friction stir-welded Al alloy joint showed extremely improved tensile strength and tenacity in a liquid hydrogen temperature range. For the low-temperature material database, both addition of new data and improvement of software were promoted. (NEDO)

  10. Achievement report for fiscal 1996 on the research and development of technologies for important region. Development of control system technology for combustion with energy use rationalized, etc.; 1996 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to develop basic technologies to build an SiC device capable of service amid high-temperature surroundings for the advancement and optimization of combustion control systems. In an SiC semiconductor, the Si-C bond is broken when irradiated with ions, and this makes the occurrence of thermal oxidation easy to occur. In the study to form SiC into single-crystal substrates, a substrate with warpage of 10 micrometers or less and surface coarseness of 10 nanometers or less is realized. In the development of sensor technologies, the high-speed CVD (chemical vapor deposition) method is applied for the growth of crystals further on a 3C-SiC layer epitaxially grown by MBE (molecular beam epitaxy) surface control, which improves on layer characteristics. Element technologies are developed for the construction of a 3-terminal element (FET: field effect transistor), which is for the construction of a high-temperature, high-speed SiC device. An effort is made at achieving 3C-SiC hetero-epitaxial growth, etc., on a 3-inch Si substrate using an SiC crystal film formation experimenting apparatus, which aims at constructing a control device. Concerning the combustion control system, the relations between the air/fuel ratio and the emission spectra of radicals OH, CH, and C2 in a flame are made clear. Also referred to are the basic studies being conducted at research institutes such as universities and a survey of technological trends abroad.

  11. Achievement report for fiscal 1998. Research and development of technologies for creating new bioaffinity molecules using submicron beads (Energy use rationalization related technology practicalization); 1998 nendo biryushi riyogata seitai ketsugo busshitsunado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the effort to develop chemical substance/bioreceptor analysis technology using submicron beads, polystyrene core/polyglycidyl methacrilate beads are used in a study started about a detachable spacer using newly developed fixation technology. In the development of bioaffinity chemical substance refining technology, two kinds of sugars and several kinds of aromatic aldehydes serve as building blocks in the construction of a library, and studies are made of analyses using liquid chromatography and mass spectrography. In the development of novel substance creation technology based on information on the analysis of chemical substance/bioreceptor, in an effort at developing technologies for creating novel function provided chemical substances, heterocyclic compounds, alkaloids, and sugar compounds are selected and their syntheses in the liquid phase and solid phase are studied, which is again for the construction of a library. (NEDO)

  12. Research and development in fiscal 1999 of university collaboration type industrial and scientific technologies. Research and development of the next generation ferroelectric memory(Development of energy use rationalization technology); 1999 nendo jisedai kyoyudentai memory no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research has been performed with an objective to develop a new circuit configuration that separates data read-out function from memory storage function. This paper summarizes the achievements in fiscal 1999. In developing a circuit simulation technology, the existing macro model was used to derive circuit response in a partially polarized condition. Comparing the hysteresis shape with an experiment revealed that the partially polarized condition can be expressed well. Incorporation into SPICE will be discussed in the future. In the research of optimizing the circuit configuration, an SrTa{sub 2}O{sub 6}/SiON buffer layer was used to have fabricated a ferroelectric gate FET being the constituting element of the memory cell. The function separation type 1T2C memory was discussed on aggregation, manufacturing processes, and optimal cell arrangement, and was concluded as a superior memory. It was disclosed that the high performance ferroelectric gate FET needs to take the FEMIS structure, and make the area of a ferroelectric capacitor smaller than the area of a buffer layer capacitor. (NEDO)

  13. Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 12. Search and assessment of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 12. Kakushinteki sendoteki kenkyu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Search and assessment were carried out on innovative and leading technologies which are outside the development objects at the present, but are promising for the future. This paper describes the achievements in fiscal 2000. In the hydrogen manufacturing method using natural gas as the raw material, but not generating carbon dioxide, a method using plasma has the hydrogen conversion rate of more than 90%, capable of providing carbon black with added value. On a hydrogen selective enzyme hydrogenase sensor, verification was given on its sensitivity and response speed, but the discussion was interrupted because of difficulty in obtaining the enzyme. Naphthenic hydrogen storage and transportation media (easy in hydrogenation and dehydrogenation) were discussed, whereas the reaction promoting effect was identified in both of the super heating liquid film process and the membrane reactor system. Enhancement in output and efficiency may be anticipated if hydrogen-rich reformed gas is obtained by reforming methane (natural gas) by utilizing waste heat from a gas turbine of several MW capacity. Hydrogen liquefaction technologies using the magnetic freezing process was discussed as the fundamental research assignment, wherein fiscal 2000 has studied the basic design and optimal magnetic materials. (NEDO)

  14. Fiscal 1974 Sunshine Project result report. R and D on solar energy system (weather survey). Part 3. Observation data on global solar radiation and sunshine duration; 1974 nendo zenten nissharyo, nissho jikan no kansoku shiryo. 3. Taiyo energy system no kenkyu kaihatsu (kisho chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    This report includes observation data on global solar radiation and sunshine duration for R and D on solar energy system. The global solar radiation data include the following measured by bimetal pyranometer in 1954-1970: Monthly and yearly mean value, average value, standard deviation, coefficient of variation, and maximum and minimum value. The sunshine duration data include the following measured by Jordan's heliograph in 1941-1970: Monthly and yearly total value, 10-year mean value, average value, standard deviation, coefficient of variation, and maximum and minimum value. Annual variations of the global solar radiation at 16 typical sites all over the country are illustrated using the average values, and secular variations of the monthly and yearly mean values at 16 sites are also illustrated. Annual variations of the sunshine duration at 17 typical sites are illustrated using the average values, and secular variations of the monthly and yearly total values at 17 sites are also illustrated. Profiles of the global solar radiation and sunshine duration, and their coefficients of variation are illustrated for every country. (NEDO)

  15. The maximum allowable temperature of zircaloy-2 fuel cladding under dry storage conditions

    International Nuclear Information System (INIS)

    Mayuzumi, M.; Yoshiki, S.; Yasuda, T.; Nakatsuka, M.

    1990-09-01

    Japan plans to reprocess and reutilise the spent nuclear fuel from nuclear power generation. However, the temporary storage of spent fuel is assuming increasing importance as a means of ensuring flexibility in the nuclear fuel cycle. Our investigations of various methods of storage have shown that casks are the most suitable means of storing small quantities of spent fuel of around 500 t, and research and development are in progress to establish dry storage technology for such casks. The soundness of fuel cladding is being investigated. The most important factor in evaluating soundness in storage under inert gas as currently envisaged is creep deformation and rupture, and a number of investigations have been made of the creep behaviour of cladding. The present study was conducted on the basis of existing in-house results in collaboration with Nippon Kakunenryo Kaihatsu KK (Nippon Nuclear Fuel Department Co.), which has hot lab facilities. Tests were run on the creep deformation behaviour of irradiated cladding, and the maximum allowable temperature during dry storage was investigated. (author)

  16. Report on the achievements in fiscal 1999 of research and development of a femto-second technology. Research and developing of a electric power generation facility monitoring system utilizing high-luminance X-ray pulses; 1999 nendo femto byo technology no kenkyu kaihatsu seika hokokusho. Kokido X sen riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Researches have been made with an objective to generate femto-second high-luminance X-ray pulses by using interactions between femto-second light pulses and high-density electron ray pulses, and to develop a technology to use the above pulses to measure objects moving at high speeds. This paper reports the achievements in fiscal 1999. In research and development of the ultra short light/electron ray pulse generating and controlling technology, totally solid laser was used as an excitation source for a mode synchronous laser transmitter. A high-accuracy moving stage driven by piezo elements and motor was used to actively control the resonator length by using the RF reference signals, wherein time fluctuation was reduced down to 100 fs level. Design and fabrication were performed on an electron ray accelerator and an electron ray transporter of the electron ray source system for Compton X-ray. Electron energy of 12 MeV and electric charge of 1 nC were achieved in an electron beam acceleration test. In the research and development of a femto-second high-luminance X-ray pulse generating technology, design and fabrication were carried out on a Compton collision chamber that can generate X-ray pulses with high luminance. (NEDO)

  17. Report on a survey in fiscal 1998 for petroleum substituting energy development and utilization in the Pacific Ocean region; 1998 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey was carried out to make available the information base that can collect, put into order and provide quickly and accurately the energy related information based on global environment problems in the Pacific Ocean region. Fiscal 1998 has performed a substituting energy demand and supply analysis in the Pacific Ocean region by adding the 1996 data, in addition to collection of the normal energy data. For the purpose of analyzing the petroleum substituting energy demand and supply in the Pacific Ocean region, data were collected from 17 countries for fiscal 1997 and the quarterly data for 1998. Retroactive data collection was also continued. The growth rate of primary energy supply in the Pacific Ocean region is 1.8% in average in the 1980's, and 3.8% in the 1990's. In contrast, the growth rate of petroleum substituting energies is 6.4% in the 80's and 6.2% in the former half of the 90's, being far higher than the growth rate of the primary energy supply. The share of the petroleum substituting energies accounting for in the primary energy supply has increased from 6.7% in 1980 to 12.1% in 1996. As the breakdown, nuclear power accounts for overwhelmingly large, followed by geothermal energy and new energies. (NEDO)

  18. Report on results 1998. Research and development on fusion area. Part 2 (chemo-intelligence); 1998 nendo seika hokokusho. Yugo ryoiki kenkyu kaihatsu daini bunsatsu (chemo-intelligence)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Chemo-intelligence is defined as artificially realizing and then materializing various functions and structures that are caused by the transmission of precise chemical information based on molecular recognition in organisms. Creation of substances/materials having functions no less superior to those of organisms enables environmentally benign, energy-saving, and resource-conserving functional materials to be realized, as materials for separation of toxic and useful substances, their sensing, and the conversion (catalysts). For this purpose, started were a computational chemical approach for molecular design, functional prediction, functional analysis, etc., to realize precise molecular recognition; an approach from synthesis of molecular recognition compounds; an approach from functional manifestation/elucidation, structural analysis, etc.; and also investigation and research on application to the materialization and systematization. The results were summarized by classifying them into molecular interactions, host molecules, ionic substance recognition compounds, super molecular structures, materialization, application, etc.. (NEDO)

  19. Report on the FY 1999 survey for making a data book related to new energy technology development. Trends of solar energy utilization, waste power generation, clean energy vehicle, geothermal power generation, clean coal technology, other new energy technology and new energy technology development; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Taiyonetsu riyo, haikibutsu hatsuden, clean energy jidosha, chinetsu hatsuden, clean coal technology, sonota no shin energy gijutsu, shin energy gijutsu kaihatsu kanren doko

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper collected/arranged the most up-to-date data made public in the new energy technology field. As to the solar energy utilization, the utilization is on the decrease with the beginning of the 1980s as a peak, and the solar systems introduced in FY 1998 totaled 15,000 and the water heaters 56,000. The waste power generation is showing a steady growth both in the general use and in the industrial use, and the introduction of 5 million KW is expected for FY 2010. The sale of the hybrid car started at the end of 1997, and the subjects are the price/performance/fuel supply system. Concerning the geothermal power generation, 497,000 KW and 36,000 KW were introduced for business use and non-utility use, respectively. Japan ranks sixth among nations of the world. Relating to the coal liquefaction, the pilot plant (PP) of Japan's original bituminous coal liquefaction NEDOL process finished operation in 1998, and the construction of technology package, international cooperation, etc. are being conducted. About the coal gasification, the construction of demonstrative equipment and operation are planned during FY 2002 - FY 2007, making use of the PP achievements of IGCC. In regard to the biomass-based waste power generation, the lignocellulose system is large in potential quantity. As to the hydrogen energy, the WE-NET project entered Period II. With respect to the ocean thermal energy conversion, the demonstrative study started. In relation to the wave power generation, a small size of approximately several hundred W was commercialized. (NEDO)

  20. FY 1997 - FY 2000 reports on the results of the development of commercialization technology of the photovoltaic power system. Summary. R and D of the photovoltaic power generation utilization system/periphery technology (R and D of high reliability storage batteries); 1997-2000 nendo New sunshine keikaku seika hokokusho (Sokatsu ban). - Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (Koshinraisei chikuden sochi no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D/evaluation were made from FY 1997 to FY 2000 of lead storage batteries that are applicable to the use for the absorption of abrupt power variations in photovoltaic power generation and peak shift/emergency use power source, and the results were summed up. In the study for prolonging the life, the following were carried out: development of the inexpensive corrosion-resistant lead alloy positive grid applicable to the photovoltaic power generation, development of the negative active material with a high sulfation control effect, selection of silica powder as electrolyte retainer, development of the charging control technology by the multi-stage constant current method, etc. As a result, energy density of the battery was more than 70W/L as a target, and the target life of 3,000 cycles was achieved in the life test. Further, cost reduction and deterioration judgment were studied. In the study of the group of batteries, a management system for group of batteries was developed. As a result of the 1-year field test, there were no problems on durability of the storage case, temperature difference among batteries, rise in temperature, etc. As to the developed seal type lead storage battery, the applicability to the photovoltaic power generation was acquired. (NEDO)

  1. Survey for making a data book related to the development of new energy technology. Cogeneration; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This is a report of 'A data book on cogeneration' surveyed by Japan Cogeneration Center under consignment from NEDO. Together with the advance of technology development, policies of new energy technology are being developed toward the introductory promotion in terms of preparation of subsidy system, field test project, advisory project for support of new energy introduction, etc. To promote the project for introducing/promoting new energy more effectively, it is necessary to arrange various data on new energy comprehensively/systematically and to prepare it as the basic data. Out of the technical fields of new energy, this report deals with the cogeneration field and collected/arranged the most up-to-date published data in terms mainly of a list of system, actual samples of introduction, subsidy system, situation of tackling it in each country, etc. The main items of data included in this report are shown below: (1) trend of cogeneration; (2) outline of system; (3) samples of introduction in Japan and abroad; (4) forecast of introduction; (5) policies on cogeneration in Japan; (6) basic technical terms. (NEDO)

  2. Research and development of photovoltaic power system. Research on surface passivation for high-efficiency silicon solar cells; Taiyoko hatsuden system no kenkyu kaihatsu. Hyomen passivation no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on research on surface passivation of high-efficiency silicon solar cells. In research on carrier recombination on SiO2/doped silicon interface, measurements were carried out on minority carrier life with respect to p-type silicon substrates with which phosphorus with high and low concentrations are diffused uniformly on the surface and non-uniformly on the back and then oxidized. The measurements were performed for the purpose of evaluating the carrier recombination at p-n junctions. Effective life time of oxidized test samples increased longer than that of prior to the oxidization as a result of effect of surface passivation contributing remarkably. In research on reduction in carrier recombination on SiO2/Si interface by using H radical annealing, experiments were conducted by using a method that uses more active H-atoms. As a result, it was revealed that the reduction effect is recognized at as low temperature as 200{degree}C, and photo-bias effect is also noticeable. Other research activities included analytic research on minority carrier recombination on micro crystalline silicon/crystalline silicon interface, and experimental research on evaluation of minority carrier life of poly-crystalline silicon wafers. 6 figs.

  3. Fiscal 1997 report on the results of the international standardization R and D. R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Rinsangata nenryo denchi no kasoku jumyo shiken hoho no hyojunka ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As for fuel cells, which are expected as a new clean energy, the R and D are being proceeded with in various fields of the world, but the standardization has not been made both in Japan and abroad. In Japan, the situation is that the information on technical terms, indication method, performance test method, and environment/safety test methods of the phosphorous acid fuel cell power generation is publicly spread. In relation to the international promotion of fuel cells to be predicted, it is necessary to internationally standardize cells themselves which are a key component of fuel cell power generation facilities. Phosphorous acid fuel cells are expected of the earliest commercialization of all, but the common test method to evaluate life characteristics of the cell stack has not been established yet. In the R and D, for the purpose of internationally standardizing test methods to evaluate life characteristics of the cell stack, a study on the acceleration life test method of phosphoric acid fuel cells was conducted in terms of the technical trend, data, standard, etc. A plan was prepared on general rules of the method to test acceleration life at the cell reaction part of the small cell, and activities also were started for setting up a technical committee for the fuel cell power system in President`s Advisory Committee on Future Technology. 29 figs., 20 tabs.

  4. Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

  5. FY 2000 study report on the study on technological development of the chemical processes of the next generation; 2000 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The technological development of the innovative chemical reaction processes is studied, in order to accomplish further energy saving, and reduction of resource consumption and environmental loads. Described herein are the FY 2000 study results. The program for systematization of the next-generation chemical processes systematically pigeonholes the undergoing projects and subjects to be studied, based on the principles of simplification, and sets the study fields of organic bulk chemicals, organic fine chemicals, highpolymer materials and inorganic materials. The program for investigation on next-generation chemical processes reviews creation and technological use of tailor-made biocatalysts, polymer materials which utilize wood resources, tailor-made reaction process engineering for handling fine particles in high-temperature reaction fields, production and processing of materials for high-performance polymer batteries, and extreme energy saving process for polyolefins, and proposes the revisions. The newly proposed study themes include novel C1 catalytic processes toward minimal wastes, and high utilization of biotechnology for novel processes to create materials. (NEDO)

  6. Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

  7. Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

  8. Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Practicalization of polymer back light (1st fiscal year); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu bun'ya seika hokokusho. Polymer back light no jitsuyoka ni kansuru kenkyu (daiichi nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are being exerted to develop technologies for fabricating polyvinyl carbazole thin film, 100 nm or less in average thickness and 400 mm square in area, for the construction of an exothermal sheet utilizing polymer semiconductor light emission diodes. Activities are conducted in the three fields of (1) the development of large area light emission sheets for use in polymer LEDs (light emission diodes), (2) the study of manufacturing technologies, and (3) the study of technologies for testing, analyzing, and evaluating the material. In field (1), a polyvinyl carbazole thin film is fabricated by the use of a low viscosity resin liquid application method, and a film fabrication technique is established for fabricating a thin film on a 400 mm square substrate within {+-}3 nm of film thickness error. In field (2), studies are conducted of an integrated large area thin film application/transportation system, application device mechanisms, and control sequences for application devices. Through studies of technical literature, exhibitions, and research institute meetings in Japan and overseas, it is concluded that the polymer back light is commercially feasible. (NEDO)

  9. Studies on utilization of nitrogen-fixing bacteria for saving energy; Chisso koteikin no katsuyo ni yoru sho energy no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Uozumi, T; Koyama, R; Horiuchi, M; Hidaka, M; Masaki, H [The University of Tokyo, Tokyo (Japan); Shigematsu, T; Inoue, A [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    This paper describes analysis and enhancement of nitrogen-fixing gene of rice root bacteria, such as Klebsiella oxytoca, Azospirillum lipoferumn and Sphingomonas paucimobilis, for realizing energy saving through conservation of nitrogenous fertilizers. For K. oxytoca, modified strain R-16 was developed, which can fix nitrogen effectively even in the presence of NH4{sup +}. Nitrogen-fixing ability of A. lipoferumn depends on the activity control by the modification of nitrogen-fixing enzyme as well as on the adjustment of transcription level by the transcription activating gene, nifA. The control gene relating to the above was analyzed by making clones. As a result, a modified strain TAl without the control by NH4{sup +} was developed. The R-16 and TAl strains were inoculated into rice sterile-cultured without nitrogen. Consequently, inoculated strains were settled in the root, which resulted in the increased vegetation weight of plant to two times heavier than that without inoculation. 9 refs.

  10. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

  11. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

  12. Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of micro-array for next generation gene analysis (1st fiscal year); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Jisedai idenshi kaiseki micro array no kaihatsu (daiichi nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are under way to construct a novel DNA (deoxyribonucleic acid) micro-array for gene diagnosis on the basis of technologies of laser scan type manipulation, nanometric position detection, and micro-machining. Using these technologies, structural changes to accompany reactions induced in the probe DNA deposited on an array are detected for the identification of the DNA. Activities are conducted in the four fields of (1) the study of probe DNA fixation technology, (2) development of an optical detection system, (3) detailed check of DNA micro-array performance evaluation technologies, and (4) a comprehensive survey. In field (1), gold colloid modified DNA molecules are designed and evaluated, and the fixation of DNA to substrates and technologies for integration are studied. In field (2), the gold colloid modified DNA is fixed on a thin gold film, and then a surface plasmon resonance (SPR) is observed in the wake of hybridization. Furthermore, a Brownian motion is observed of the metal particles fixed on a glass substrate via DNA. (NEDO)

  13. Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of system-on-chip mobile IC power source (1st fiscal year); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. System on chip mobile IC dengen no kaihatsu (daiichinendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop a switched capacitor (SC) integration technology based on the technology of switched capacitor power sources capable of efficiently performing voltage conversion without using magnetic parts such as coils. Activities are conducted in the six fields of (1) deciding on a programmable SC circuit, (2) circuit simulation, (3) layout design, (4) marketing and the contents and results of the studies, (5) profitability and the contents and results of the studies, and (6) a patent information survey. In field (1), a series fixed type DC-DC converter and a ring type converter are compared with each other in terms of electrical and theoretical characteristics, the number of devices to constitute the circuit, and ease of control, and the ring type converter is selected to serve as a general purpose SC power source. An efficiency simulation is conducted, as the result of which it is proved that the power source have the features that a practical power source should have. In field (2), for carrying out integration for the selected SC power source, a circuit simulation is conducted for the disclosure of IC power source constituent characteristics and dimensions are determined for the layout. (NEDO)

  14. Report on the results of the FY 1999 R and D of the medical welfare equipment technology and the development of an implantable total artificial heart system using a non-pulsatile pump. R and D of an implantable total artificial heart system using a non-pulsatile pump (R and D of the functional/cure artificial heart); Iryo fukushi kiki gijutsu no kenkyu kaihatsu tainai umekomigata jinko shinzo system 1999 nendo seika hokokusho. 5. Renzokuryu pump wo mochiita tainai umekomigata jinko shinzo system no kenkyu kaihatsu (kinoteki chiryoteki jinko shinzo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    The R and D of element technology were made on non-pulsatile pump, drive/controller, energy supply storage system, structural coating materials, etc., and the prescribed target was achieved. In the R and D of a total system, a blood-removing conduit with movability was designed to avoid the functional inlet obstruction, and the animal experiment was carried out. In the short-term chronic animal experiment on the implantation of a single bypass model using this artificial conduit and in the animal experiment for implantation of functional/cure artificial heart, it was confirmed that the operation was conducted easily, the flow rate of the blood of the artificial heart is extremely stable, and the blood-removing conduit functions favorably. In the R and D on Tele-TAH with the aim of future home medical treatment, it became possible to acquire via monitor the pump drive information and blood circulation state information on the animals tested in the breeding farm. The remote medical simulation was made. (NEDO)

  15. Achievement report on research and development in the Sunshine Project in fiscal 1978. Studies on a hydrogen energy total system; 1978 nendo suiso energy total system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    Analysis was made on timing, patterns and scales of introducing hydrogen energy into the Japan's total energy system, and case studies were made on transfer of the comprehensive systems that can be realized in the years of 1985, 2000 and 2025. The basic conception for the analytic method employed a method to analyze and present theoretically the conditions in which prerequisites or results of the estimation can be established, rather than intending elucidation of the estimation itself. An energy model was used for the theoretical means thereof. The objective function to be optimized was assumed to maximize (estimate over the planned period of time) the total effectiveness of the hydrogen energy system converted into the present value being given appropriate discount. The economic performance measures for different secondary energies working as the comparison measures are the limiting production cost of each energy. A consideration was given to the point that the electrolytic hydrogen cannot compete with that made by using the thermo-chemical method (if developed successfully) using heat from high-temperature gas reactor if the fossil fuel price rises sharply. Considerations are also required in replaceability of hydrogen energy with other energies, and hydrogen utilization in petroleum refining. (NEDO)

  16. FY 1997 report on the research study for preparation of NEDO`s vision. Biomass energy; 1997 nendo chosa hokokusho (NEDO vision sakutei ni muketa chosa kenkyu). Biomass energy ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research study was made on the current usage, technological development and future subjects of biomass energy. The current use of biomass energy over the world estimated to be nearly a billion t/y oil equivalent. This value is estimated to be only a part of a pure primary biomass yield of 73 billion t/y oil equivalent showing a large supply potential. The evaluation result of a biomass energy potential in the world by GLUE (Global Land Use and Energy Model) considering worldwide biomass flow and competition of land use showed that no change of land use form in advanced areas is predicted, and no production of new biomass energy from forests in advancing areas is also expected. Production of biomass energy from farm products is promising in advanced areas, while the potential of biomass residue is high in advancing areas showing the possibility of energy development. Development of new biotechnologies such as molecular control of bio-production functions is expected to increase biomass resources. 76 refs., 26 figs., 30 tabs.

  17. Research and development of the industrial basic technologies of the next generation, 'composite materials (quality evaluation techniques)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (hinshitsu hyoka gijutsu)'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing composite materials as the basic technologies of the next generation are evaluated, and the directions of the R and D evaluation for the second phase are set up. The efforts in the first-phase R and D project are aimed at development of methods for measuring carbon fiber surface structure elements; confirmation of the relationship between adhesive shear strength and active surface area; development of methods for determining fracture toughness by standard specimens; estimation of allowable void fraction for inter-layer shear strength; defect detection and quality evaluation by electromagnetic, ultrasonic, laser holography and AE methods; development of methods for detecting resin setting reactions during the molding processes; and understanding deteriorated mechanical characteristics of the resin-based composites by environmental factors, among others. The objectives of the first-phase project have been almost achieved. It is decided that the second-phase R and D project are directed to investigations on the relationship between surface properties of the fibers in the composites and fiber/matrix adhesion; researches on mechanical characteristics involved in fracture of the structural elements; evaluation of mechanical properties of the metal-based composites and investigations on detecting their defects; elucidation of the effects of environmental factors on their strength; and development of the techniques for integrating detection of molding-induced cracking and that of setting reactivity, among others. (NEDO)

  18. National research and development project. Report on evaluation of research and development of remotely controlled excavators for highly deep submarine oil fields; Ogata kenkyu kaihatsu project. Daishindo enkaku sosa kaitei sekiyu kussaku sochi no kenkyu kaihatsu ni kakawaru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-02-04

    Described herein are results of evaluation of the developed excavators remotely controlled for highly deep submarine oil fields. The excavator system was designed to work at the target water depth of 200 to 250 m and excavation depth of 8,000 to 9,000 m, though not quite satisfactorily. There were several practical problems to be solved, e.g., those found in accuracy of reentry in the excavated section, cables connecting the driving equipment to the excavated section, and entangled hoses. The works were divided and system was configured in an attempt to secure all-weather type serviceability and to improve economic viability. The other major works included attempts to improve equipment functions and reduce manpower cost. Nevertheless, however, the construction cost was considered to be higher than expected, and no firm prospect was obtained whether the new excavator system was economically competitive with the conventional rig. The factors that pushed up the construction cost were various facilities needed by the new system with the separated excavation and driving sections, e.g., those facilities for helping the system land on the sea bottoms, material supply/storage facilities, and automated/unmanned facilities. The system failure and other items related to reliability are no clearly understood, making it difficult to compare it with the conventional rig in service factor. It was not adequate, therefore, to advance the next R and D phase as planned, and decided that the project was suspended to see the world development trends, because the clear plans for the future could not be drawn at that time. (NEDO)

  19. Fiscal 1974 Sunshine Project result report. R and D on solar heat power generation system (R and D on curved reflector light collection system); 1974 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. kyokumen shuko hoshiki system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-30

    This report composed of 6 parts summarizes the fiscal 1974 Sunshine Project research result on the solar heat power generation system with a curved reflector light collection system. Part 1 outlines the research target, research result and research system. Part 2 describes each research item in detail. This part on system and hardware researches is composed of (1) study on 1,000kW system, (2) development of plane/parabolic reflector light collection equipment, (3) development of parabolic reflector light collection equipment, (4) development of selective transparent membrane and selective absorption surface, and (5) study on heat storage equipment and heat exchange equipment. Part 3 describes the future R and D plan for every year focusing the fiscal 1975 R and D plan. Part 4 describes various cooperative activities with other research groups such as various committees related to the Sunshine Project, universities and Electrotechnical Laboratory. Part 5 describes several patents produced during this R and D. Part 6 summarizes the results on this R and D. (NEDO)

  20. Achievement report on research and development of the industrial basic technologies of the next generation in fiscal 1981. Research and development of composite materials; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Fukugo zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Described herein are the results of the FY 1981 research and development for composite materials, established by the R and D system for the basic technologies of the next generation. The R and D project for resin-based composite materials involves basic researches on the matrix resins, and surface modification of the reinforcing fibers. The investigations and basic tests are conducted for monolithic molding, other types of molding, and cutting and boring by, e.g., laser beams and water jet. The other related efforts include researches on analysis theories for optimization of strength and rigidity of the composite structures, and development of the optimization programs. For the R and D project for the metal-based composite materials, the efforts are directed to understanding wettability and reactivity of the reinforcing fibers with metals, and development of the techniques for producing various types of preforms and compositing methods. The basic researches are conducted for hot pressing/rolling molding, extrusion/withdrawal, powder molding and melt molding of the composite materials with aluminum alloys as the matrices. The other R and D items include investigations on methods for evaluating qualities for the steps form the stock preparation to production of the final products. (NEDO)

  1. 'Research and development of research information infrastructure'. Achievement report on development of parallel processing software technology for discrete value solving methods; Kenkyu joho kiban kenkyu kaihatsu seika hokokusho. Risanka suchi kaiho no tame no heiretsu shori software gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Research and development has been performed on a general purpose parallel processing software that can be utilized for value solving methods, such as the finite element method, finite volume method and finite difference method. The achievements of the research and development may be summarized as follows: this parallel platform is parallelized in the concept of the domain division method for the elements (calculation cells), and is applicable to any of the finite element method, finite volume method and finite difference method; a researcher who has developed a program can easily perform the parallelization work to have the parallelizing performance displayed; the platform can be utilized in agreement with several parallel levels that are required by the user; with regard to the parallelization efficiency in large-size problems, it has become possible to execute at an efficiency of higher than 70% for the solver parts by using 32 processors of SR8000 at the computation center of the Agency of Industrial Science and Technology; the rigidity matrix preparing part shows an efficiency close to 100%W; and the developed parallel platform is under continued evaluation at the Machine Technology Research Institute and the Material Engineering Research Institute. (NEDO)

  2. Fiscal 1976 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on Si ribbon crystal vertical pulling method); 1976 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Silicon tatehiki ribbon kessho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-31

    This report describes the fiscal 1976 research result on Si ribbon crystal vertical pulling method for photovoltaic power generation systems. The equipment for simultaneous growth of 3 ribbon crystals was designed and prepared in consideration of capillary die arrangement, vertical pulling method and control method of temperature profiles on the die surface. The temperature profiles on the die surface were controlled by subheaters for 3 parts of each capillary die which were divided longitudinally. Ribbon crystals grew up to 5mm simultaneously through both end dies. By cooling a part of crystal, fast pulling is probably possible. Study was made on the correlation between various crystal defects of Si ribbon crystals and cell characteristics, and in particular, basic characteristics of SiC deposited particles by SEM observation to reduce their impacts. Possibility of simultaneous vertical pulling of crystals was verified by using a capillary carbon die for multi-pulling. Although crystals grew by eutectic reaction under saturated dissolution of carbon, crystals with no transition were obtained. An SiC-coated die was excellent rather than carbon one. (NEDO)

  3. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on second term final research and development (first report); Jisesdai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu bunshi bunrimaku zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This study is intended to establish a basic technology for innovative high-efficiency separation membrane materials that can be used in areas in which application of membrane separation has been impossible. The water/ethanol separation membrane (for water selective permeation) and water/acetic acid separation membrane (for water selective permeation) achieved separation coefficient and permeation velocity of the world's highest level. The water/ethanol separation membrane (for ethanol selective permeation), although its separation coefficient is lower than the world's highest performance, has high permeation velocity, providing the performance of the worldwide level as seen from the comprehensive viewpoint. The carbon monoxide/nitrogen separation membrane achieved separation coefficient and permeation velocity of the world's highest level. The oxygen/nitrogen separation membrane requires further enhancement in the permeation velocity and stability. Establishment has been performed on separation technologies for membrane separation of non-water soluble aqueous solutions, optical division by using chiral crown ether, high-performance liquid separation by means of plasma surface treatment, and particle separation. Basic analysis has been advanced also on evaluation technologies for gaseous body separation membrane and liquid separation membrane, of which future progress is expected. (NEDO)

  4. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  5. Fiscal 1976 Sunshine Project result report. R and D on solar heat power generation system (R and D on tower solar collection system); 1976 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. Tower shuko hoshiki system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-05-27

    This report describes the fiscal 1976 research result on tower solar collection system for solar heat power generation systems, and summarizes main specifications of the subsystem, equipment and control of the 1,000kW pilot plant. Based on daily and monthly long-time simulation, various programs were prepared for power generation, heat storage and operation rate of equipment, and real arrangements for total simulation were made. The output fluctuation rate less than 1%/min was obtained by studying a control system flexible for drastic fluctuation of solar radiation using the newly prepared dynamic characteristic equation for a steam loop. 10kW solar collection test was carried out using a pancake type heat absorber. Practical basic analysis was made on a heliostat driving system. A cavity type heat absorber was adopted in consideration of cost, operability and heat discharge. Based on thermal characteristics of a heat storage type heat exchanger using molten salt as heat medium, basic experiment was made on a compact latent heat type heat exchanger. Basic studies were also made on reflector, selective absorption surface and heat storage material. (NEDO)

  6. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  7. Research and development of the industrial basic technologies of the next generation, 'composite materials (highly functional, crystal-controlled alloys)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'koseino kessho seigyo gokin'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing highly functional, crystal-controlled alloys as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop alloys superhighly resistant to heat, heat-resistant/high-rigidity and light/high-rigidity by controlling their crystals. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at designs of a total of 12 types of single-crystal alloys by the computer-aided alloy designing techniques, production of these alloys on a trial basis, and evaluation of their characteristics, for the alloys superhighly resistant to heat. Two of them are confirmed to be superior to the others, and selected as the alloys to be developed. This project has also established the single-crystal casting techniques, which allow crystal orientation almost completely. Various types of heat-resistant/high-rigidity and light/high-rigidity alloys are designed, produced on a trial basis, and evaluated for their characteristics. As a result, one alloy type is selected for each category. The other techniques developed by this project include those for adjusting powders for light/high-rigidity alloys whose average grain sizes are controlled and impurity contents are reduced. Bright prospects have been obtained for the techniques for superplastically forging the disk shapes. These efforts have almost achieved the development objectives of the first-phase R and D project. (NEDO)

  8. Fiscal 1976 Sunshine Project result report. R and D on solar heat power generation system (R and D on curved reflector light collection system); 1976 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. Kyokumen shuko hoshiki system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    As a part of Sunshine Project, study was made on the solar heat power generation system using a solar collection system composed of plane and curved reflectors. In fiscal 1976, study was made on plant characteristics and plant operation by using system simulation program, and the concept design of the system was promoted. The reflectance of the plane reflector was improved up to 0.92 by remodeling the prototype collector fabricated in last fiscal year, and the prototype test facility of full-scale reflectors for 1,000kW solar power plant was prepared to obtain design data for large reflectors. The prototype heat collection loop control equipment which was prepared to simulate control of plant operation conditions according to solar radiation fluctuation, succeeded in prediction of solar radiation fluctuation within nearly 30min. New study was also made on a system using both accumulator and molten salt heat storage equipment, and each proper capacity for power plants was determined. In addition, high-temperature vapor generation for 2 hours was achieved by the prototype heat storage equipment using KCl-LiCl molten salt. (NEDO)

  9. FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

  10. FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

  11. FY1998 survey on preparation of data collection related to new energy technology development (cogeneration); 1998 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa (cogeneration) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    New energy technologies have had the subsidy institutions established in association with advancement of the technologies, and such introduction promoting measures developed as the introduction assistance and advisory project. To promote this development more effectively, it is necessary that different data related to new energies are put into order comprehensively and systematically to be retained as the basic data. Therefore, this paper collects and puts into order the latest published data on cogeneration from among other new energy technology areas, with main regard to system listing, specific introduction examples, subsidy institutions, and how other countries are working on the technologies. Hydroelectric power generation uses up head energy of water by installing power plants along a river from higher location to lower location. Similarly the cogeneration is a kind of multi-stage energy utilization (cascade utilization) system that uses up energy serially from as high oil and natural gas combustion temperature as 1,500 degrees C or higher down to temperature levels used for hot water supply and air conditioning as low as 45 to 50 degrees C. It generates electric power by using a thermal engine, and utilizes waste heat effectively. (NEDO)

  12. Research and development of utilization technology of solar thermal system for industrial and other use. Research and development of solar system (research for solar/energy-conservation technology retrofitted to existing buildings); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Solar system no chosa kenkyu (solar toshi muke gijutsu ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for solar/energy-conversion technologies retrofitted to existing buildings. The estimated effects and economic viability of retrofitting technologies show that they bring very high energy-saving effects when applied to heating and hot water supply, which consume a large portion of energy, but relatively low energy-saving effects when applied to cooling, solar walls, glazed balconies and transparent insulators. The study on applicability of these technologies in Japan indicates that the technologies which can recover cost within an average life time are those applied to windows, solar collector systems for hot water supply and heating, and transparent insulators. Although these technologies are low in applicability to cooling viewed from the angle of cost recovery, retrofitted radiation type cooling systems improve not only cooling and energy-saving effects but also comfortableness.

  13. Development in fiscal 1999 of technology commercializing photovoltaic power generation system. Research and development of power generation application system and peripheral technologies (Survey and research on evaluation of photovoltaic power generation); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden hyoka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective of evaluating the contribution to the global environment of utilization of photovoltaic power generation, discussions were given on evaluation of photovoltaic system life cycle, evaluation of contribution to environment, and total evaluation. This paper summarizes the achievements in fiscal 1999. In evaluating the PV system life cycle, the roof-integrated modules using the thin film CdTe cells were selected as the evaluation object to estimate the energy payback time (EPT) and the CO2 emission unit consumption rate. In case of annual production of 10 MW, the EPT is 1.8 years and the CO2 emission unit consumption rate is 13 (g-C/kWh), which were found largely reducible by expanding the annual production size. For the environmental contribution evaluation which focuses on CO2 emission suppression effect as the discussion object, discussions are being given on the introduction scenario needed for the analysis. In the total evaluation, the direct employment effect assumed in Japan was discussed on production, distribution sales, installation, maintenance control and dismantling of photovoltaic generation system for residential use. The discussion showed the effect of about 7 persons per year per MW in production size of 100 MW. (NEDO)

  14. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 3. Study on the global network; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 3. Global network kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the WE-NET project, the introduction condition of hydrogen as substituting energy and CO2 reduction effect were analyzed using a global energy model. The WE-NET project aims at global-wide introduction of clean energy by converting abundant renewable clean energy into hydrogen transportable to distant consumers all over the world. The study result in fiscal 1996 is as follows. Undeveloped hydroelectric resources in the world are estimated to be 12 trillion kWh/y equivalent to the existing developed one in the world. Since the cost of the hydroelectric power generation projects over 1000MW in the planning stage is estimated to be 0.02-0.05$/kWh lower than that of other renewable energies, such projects are expected as energy source in the initial stage of the practical WE-NET project. The GREEN model was modified by adding a hydrogen analysis function, and extending an analysis period. The modified model allowed evaluation of the long-term important role of hydrogen energy, in particular, the capability of CO2 gas reduction all over the world. 28 refs., 92 figs., 56 tabs.

  15. Fiscal 1999 survey report. Survey of development and utilization of energy substitutes for oil in the Pacific region; 1999 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The Pacific region is a densely populated region where economy is developing at a high pace with China and other newly industrialized economies at the core. When energy balance in the region is studied, it is found that China and some others have already turned pure importers of energy and that probabilities are high that, along with development of economy and improvement on living standards, all the nations in the region will become pure importers. Accordingly, in the presence of urgent problems of global pollution and oil resources depletion, it is important to make sure that data particularly about the development of substitute energies for oil in this region be collected and duly dealt with for accurately predicting future developments. In this survey, a database is to be built to grasp the trends of energy supply and demand with attention focused on substitutes for oil which are available at hand. In this fiscal year, data for 1997 were added to the database for analysis into demand and supply of substitutes for oil in the Pacific region, and energy data were gathered for this purpose. Detailed tables of balance were compiled, broken down by energy source. Other detailed tables of balance were also prepared, these broken down by ultimate consumption department. (NEDO)

  16. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / R and D of a task adaptation type group architecture transfer robot system, TRIPTERS (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / task tekigogata gun kosei hanso robot system TRIPTERS no kaihatsu kenkyu (daiichi nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper stated the fiscal 1997 result of the development of a task adaptation type group architecture transfer robot system (TRIPTERS) which can cope with changes in carrying task rapidly and flexibly. R and D were conducted mainly of various functional modules, the operation management technology which enables group architecture, and the basic design of a standardized transfer robot. As to the positioning, studied were the construction of the basic hardware of laser position measuring device, and the application method. Concerning the cooperative carrying, conducted were securing of positioning accuracy of matters to be carried, high speed heavy transfer control, and design of dead reckoning system. Relating to the operation management, passable areas were divided into more than one zones, and the effective path reservation method was constructed so that one and the same zone is not occupied. As to the environmental recognition/obstacle avoidance, developed were actual hour/distance acquisition equipment, and autonomous cars running according to the directions of the color sign recognition system by stereo CCD camera. Also conducted were the development of methods to recognize the distance to obstacles and to discriminate areas, the development of mobile sensor, and the basic experiment on running of the demonstration machine. 44 refs., 153 figs., 15 tabs.

  17. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Final year report. R and D on the bio-fuel production by high functional bio-reactor; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Kokino bio reactor ni yoru bio nenryo seisan ni kansuru kenkyu kaihatsu (saishu nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A system was developed for producing automobile fuel from the recycled paper and waste cooking oil using high functional intelligent yeast. Element technology is the functional yeast creation technology and the online intelligent control technology of the process into which the fixed bio-reactor was inserted. Studies were made on the following: 1) creation of high activity lipase production/ethanol production yeasts; 2) bio-fuel production by intelligent bio-reactor; 3) process optimization control technology by fuzzy control; 4) stabilization of bio-fuel production yeast; 5) comprehensive investigational study. In FY 2000, the results were obtained as written below: development of the stable lipase coming from rhizopus japonicus, fixed bacterium using rhizopus oryzae fungus body which can be used more than ten times, direct ethanol fermentation from starch by developing the multi-copy glucoamylase manifestation yeast, operation of a 20L capacity bench plant, etc. (NEDO)

  18. Summary of research achievements in fiscal 1978 in research and development of new energy technologies (Research and development expense for the former half period); 1978 (kamihanki) nendo kenkyu seika no gaiyo. Kenkyu kaihatsuhi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-07-01

    This paper describes the summary of research achievements in fiscal 1978 in research and development of new energy technologies at the General Research Institute of Electronics Technologies using the NEDO's development expense. For measurement of solar beam spectral radiation illuminance, measurement data in ultraviolet and visible zones were collected. Comprehensive adjustment was performed on near infrared zone measuring devices. In solar thermal power generation, discussions were given on three kinds of collector combinations as a study on enhancement and optimization of functions in small-size system models. Fundamental studies on solar cells are continuing, including those for compound and amorphous semiconductors. Development of new electrode materials having large work function, and module performance tests are being progressed in order to realize solar heat electron power generation. In hydrogen manufacturing using the high-temperature direct pyrolysis method, studies are being performed on thermal decomposition performance and the hydrogen separation method (using separation membranes). Regarding hydrogen fuel cells, power generation experiments were executed by using zirconia solid electrolyte type fuel cells. Methodological development is being moved forward to realize a total energy system including the future societies and nature. This paper also describes experimental studies on power generation using ocean temperature difference. It also describes high-temperature ionization gases and superconducting magnets as the seeds of new energy technologies. (NEDO)

  19. Summary of research achievements in fiscal 1978 in research and development of new energy technologies (Research and development expense for the former half period); 1978 (kamihanki) nendo kenkyu seika no gaiyo. Kenkyu kaihatsuhi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-07-01

    This paper describes the summary of research achievements in fiscal 1978 in research and development of new energy technologies at the General Research Institute of Electronics Technologies using the NEDO's development expense. For measurement of solar beam spectral radiation illuminance, measurement data in ultraviolet and visible zones were collected. Comprehensive adjustment was performed on near infrared zone measuring devices. In solar thermal power generation, discussions were given on three kinds of collector combinations as a study on enhancement and optimization of functions in small-size system models. Fundamental studies on solar cells are continuing, including those for compound and amorphous semiconductors. Development of new electrode materials having large work function, and module performance tests are being progressed in order to realize solar heat electron power generation. In hydrogen manufacturing using the high-temperature direct pyrolysis method, studies are being performed on thermal decomposition performance and the hydrogen separation method (using separation membranes). Regarding hydrogen fuel cells, power generation experiments were executed by using zirconia solid electrolyte type fuel cells. Methodological development is being moved forward to realize a total energy system including the future societies and nature. This paper also describes experimental studies on power generation using ocean temperature difference. It also describes high-temperature ionization gases and superconducting magnets as the seeds of new energy technologies. (NEDO)

  20. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / Development of an environmentally friendly industrial cleaning system using near-critical and supercritical carbon dioxide (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / chorinkai ryutai wo mochiita kankyo chowagata kogyo senjo sochi no kaihatsu (daiichi nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In the manufacturing process of semiconductors and in the high tech industry, cleaning is indispensable. At present, when regulation of the use of CFC which used to be much used has been decided on, the conversion to the use of substitutes for CFC cleaning is urgently needed. Transfer to cleaning by water/alcohol/hydrocarbon has been proceeded with, but there are a lot of problems. Out of the development of the cleaning method using supercritical fluid, the paper described the fiscal 1997 result. As to enhancement of efficiency and decrease in size of equipment, a cleaning experiment by high pressure CO2 around the critical point was conducted by integrating nozzle, ultrasonic generator and cavitation generator and adding solvent circulating system. Multi-purpose and energy saving of the equipment were also studied. To establish an analysis method for the cleaning degree, the contaminated component film of trace organic matter with a specified thickness was formed on the silicon wafer, and using the Fourier transform ultrared spectroscopy, a method to determine the film thickness was studied. For the function evaluation for precision machine parts and determination of optimum cleaning conditions, the cleaning/degreasing process of valves were compared with the conventional method. For the product manufacturing, the paper investigated and prepared the data in Japan and from abroad. 55 refs., 79 figs., 18 tabs.

  1. FY 2000 report on the results of the R and D of the technology for rationalization of energy utilization and for CO2 fixation using recycled paper; 2000 nendo energy shiyo gorika koshi nado yuko riyo nisanka tanso koteika gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this R and D, the recycled paper, etc. composed mainly of cellulose are degraded (saccharified) up to saccharides in a biological method. The saccharides and CO2 obtained are converted into useful substances such as organic acid using the bacterium function. The aim of the R and D is to develop this conversion (bioconversion) technology and to establish the technology to make an effective use of the recycled paper, etc. as useful chemical raw materials/substances and energy. In FY 2000, study was made mostly of the saccharification and bioconversion. As to the saccharification, conducted were the collection of the bacteria for cellulose degrading enzyme production which have been found so far and the evaluation of degradation of the recycled paper. And, as to the bioconversion, conducted were the survey and isolation of enzyme proteins and genes which are concerned in it in the process toward the formation to organic acid from saccharides and CO2, and the analysis of part of them. In this report, introductory remarks were described in Chapter 1. In Chapter 2, the results were summarized of the study on saccharification of the recycled paper. In Chapter 3, the results were outlined of the study on the bioconversion technology. This technology development was aimed at establishing new high efficiency bio-processes. (NEDO)

  2. FY 1992 Report on the results of the research and development of micromachine technologies. R and D of highly functional maintenance technologies for power generating systems; 1992 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Described herein are the FY 1992 results of the R and D project aimed at development of microcapsules, mother machines, examination modules without retrieval and working modules with retrieval, and their application to total systems for development of the highly functional maintenance technologies for power generating systems. Researches on the microgenerators involve studies and extraction of technical problems for structures, thin-film magnet production methods, coil winding methods, high-speed microbearings and microaccelerators. Researches on the mother machines involve development of the basic elements, on a trial basis, of the electrostatic actuators for the mechanisms of driving the main bodies, and evaluation of their characteristics by a minute torque analyzer. Researches on the examination modules without retrieval involve basic studies on, e.g., expansion driving, supersonic and microwave energy conversion devices for the expansion transfer mechanisms, development of these devices on a trial basis, evaluation of their functions, and extraction of the problems. Researches on the working modules with retrieval involve studies on shape memory alloy materials for tubular manipulators and actuator mechanisms. (NEDO)

  3. Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

  4. Fiscal 1999 achievement report on interuniversity coordination type research and development of industrial technology. Research and development of highly functional material designing platform; 1999 nendo kokino zairyo sekkei platform no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of enabling prediction of structures and properties of polymeric materials by computer-assisted experiments, studies were conducted for putting new simulation technologies to practical application. With the coarse-graining molecular dynamic method working group, a coarse-graining molecular dynamic engine high in generality and augmentability was developed so that an optimum coarse-graining model might be chosen and constructed to achieve any given purpose, and its installation was almost completed. The dynamic mean field method working group fabricated a new general-purpose simulator with its interface simplified and function improved. A simulation technique was also developed, which would be incorporated into the general-purpose simulator. The dispersed structure simulation working group developed a group of class libraries for use in continuum simulation. The platform working group, making use of Java excellent in general-purpose feature, worked out a function verification platform to run on Windows95/98/NT. (NEDO)

  5. Research and development of laser radar for environmental measurement. 2; Kankyo keisokuyo laser radar no kenkyu kaihatsu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This project was received by Optoelectronic Industry and Technology Development Association from NEDO, and aims to contribute to the improvement of Indonesia's environmental administration through the development of an air pollution observing laser radar (LR) and of an environmental information network system fit for use in the country in cooperation with Indonesian engineers. LRs will be installed at several sites in an urban area where environmental problems are increasingly serious, and a observation network system will be constructed to link the laser radar sites. The observed data will be collected, analyzed, and processed by an observation data processing center for the investigation of the three-dimensional spatial distribution of air pollution to determine the actual state of air pollution over an urban area. The laser radars and the network will be placed in the city of Djakarta. The Indonesian authority responsible for the project is Indonesian Institute of Sciences. In fiscal 1994, part of the equipment (difference absorbing LR) was designed and manufactured, the design of the environmental information network system was developed, and various researches required in this connection were conducted. (NEDO)

  6. Report on the FY 1999 R and D on high temperature superconducting flywheel energy storage. System design/evaluation (Comparative study and information collection); 1999 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu. System sekkei hyoka (hikaku kento, joho shushu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Following the previous fiscal year, a flywheel technology survey committee by men of learning and experience was organized to make a comparative study on various flywheel energy storage systems. Concerning the list-making for checking each element of the high temperature superconducting flywheel system, characteristics and reasons for employment of the small model and medium model were outlined in terms of the system structure (structure in single unit, structure in more than one units), flywheel, bearing, electrically-driven generator, etc. Also about the system in which no superconducting magnetic bearing is used, the information is collected in Japan and abroad through internet, etc., to outline the system. Further, main results obtained in the project were made public in main international conferences or academic meetings such as EUCAS and ISOTC108. At the same time, visits were paid to research institutes such as Cambridge University in the U.K. for the purpose of supplementing the survey so far made, to investigate the recent trend of the research. (NEDO)

  7. Report on the survey in fiscal 1998. A survey on long-term energy technology strategy (a survey related to arrangement of information groups and aiding means for establishing policies related to research and development of energy and environment technologies); 1998 nendo choki energy gijutsu senryaku chosa. Energy kankyo gijutsu kenkyu kaihatsu ni kakawaru seisaku kettei no tame no johogun no seibi narabi ni shien shuho ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper discusses aiding means for establishing the research and development strategy for maximizing greenhouse effect gas reduction for a short period (year 2010) and an ultra long period (year 2030 and on). First, the situation surrounding the existing energy and environment technologies and technological assignments (themes) were put into order. Rough calculations were made on the selected themes as to their effect of greenhouse effect gas reduction. Based on the result of these reduction amount calculations, provisionary introduction scenarios including analyses by groups and users were prepared according to each theme. On the other hand, data groups related to the energy and environment technologies were investigated and put into order. The data groups include literatures and achievements of the past researches, and are expected of utilization for estimating the introduction potential to calculate effects of future research and development. In addition, discussions were given on methods to analyze cost-effect relationship in the energy and environment technologies. Importance was placed on the case surveys inside and outside the country, and simple models suitable for themes in the New Sunshine Project were built for an attempt of case studies. (NEDO)

  8. Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects on the development of photovoltaic power system practical application technologies. Research and development of a photovoltaic power demonstration system (Research and development of private house systems); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden demonstration system no kenkyu kaihatsu (kojin jutakuyo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Private house systems are investigated for system constitution, detailed design is drawn, and a model house is built. For system control and protection, the power conversion unit is provided with a control which functions to constantly maximize the output. The power conversion unit without an internal oscillator is equipped with another control which functions to output single-phase AC power coincident with the commercial system in voltage and frequency when it is interconnected with the system. The power conversion unit is so designed that it is automatically stopped for the prevention of reverse voltage imposition on the commercial system in case of interruption in the commercial system. In the study of roof panel type solar cells, real-size panels are designed and fabricated, capable of a total of 3kWp. In the study of element devices, a real-size conversion unit is experimentally built and tested in combination with a rectifier and solar cells, and it is found that the unit functions as expected. A model house is designed incorporating the results of the above-said research, and is built in the precinct of a laboratory of the Fuji Electric Co., Ltd. (NEDO)

  9. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

  10. Report of FY 1997 on the international cooperation project. Survey of globalization of the effective energy resource utilization technology (development of high-accuracy acceleration measurement system); 1997 nendo kokusai kenkyu kyoryoku jigyo. Energy shigen yuko riyo gijutsu kenkyu kokusaika chosa (koseido kasokudo keisoku system no kaihatsu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report describes effectiveness of a system for measuring the acceleration and force in high accuracy by combining a laser interference meter and a vibration stand. A possibility of pressure sensitive paper to the impact force measurement in the collision examination is also described. The results obtained in FY 1997 are as follows. For the investigation of calibration system of acceleration and force sensor, one-dimensional interferometer system has been developed, which is standardized in ISO5347 accelerometer calibration. Thus, an interference fringe processing software has been made. Moreover, construction of a three-dimensional interferometer system has been started. For the characterization evaluation of pressure sensitive papers, it was succeeded in obtaining an elasticity wave pulse maximum about 1 msec by adopting the flight body made of resin. As a result, evaluation of the force sensor in the frequency area has become possible. To calculate the displacement of a body structural material in the collision experiment, an acceleration sensor has been made for trial purposes. For the international research cooperation, the working plan of a joint research with US Texas Christian University has been concluded. 11 refs., 73 figs., 23 tabs.

  11. Fiscal 2000 collection of manuscripts for technology development committee on hydrogen energy and the like; 2000 nendo suiso energy nado kanren gijutsu kaihatsu iinkai yokoshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-07

    The subjects listed in the collection are (1) the research and development of international clean energy system technology utilizing hydrogen (WE-NET - World Energy Network), including the outline of the project as a whole; research on system evaluation; research and development of safety measures; development of technologies for liquid hydrogen transportation and storage; research on low-temperature materials; development of hydrogen supply station and hydrogen-driven automobile system; development of supply station for hydrogen produced by electrolysis of water; development of hydrogen fuel system; development of hydrogen production technology; development of hydrogen absorbing alloys for dispersed hydrogen transportation and storage; development of polymer electrolyte fuel cell fed with pure hydrogen; and the development of power generation technology, (2) the development of closed type high-efficiency turbine technology capable of carbon dioxide recovery, and (3) the development of frontier technology of carburation using sensible heat in coke oven gas. (NEDO)

  12. Report on achievements in fiscal 1998. Development on an immediately effective and innovative energy and environment technology (Research and development of an information terminal LSI requiring very low power consumption); 1998 nendo sokkoteki kakushinteki energy kankyo gijutsu kaihatsu seika hokokusho. Gokuteidenryoku joho tanmatsuyo LSI no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    It is intended that the technology for SOI expected of consuming very small power and operating at high speed be realized as an information terminal LSI for the coming 21st century. Therefore, research and development is made on the fundamental technology for LSI which operates in CMOS devices at high speed even with as very low voltage as about 0.5V by applying the optimized digital and analog circuit technology. Specifically, the aim is placed on enhancement of drive capability of transistors over that in the present devices, reduction of load capacity, and a very thin film complete depletion type SOI device that can be most expected of reduction of area as the main subjects. It is also intended to establish a method to realize very low power consuming LSI by using a CMOS circuit (a multi threshold value type CMOS circuit) that uses transistors with different threshold voltages and is optimized for the above SOI device. The achievements in this fiscal year include: a prototype 256kbSRAM was fabricated by using different design rules and wafer sizes, and the performance evaluation thereon was obtained; investigations were carried out on selection of SOI models for circuit simulation and on a high accuracy complete depletion type SOI models; and design criteria required for LSI design were put in order for comprehensive trial fabrication. (NEDO)

  13. Report on fiscal 1999 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (development of technology for rationalizing use of energy); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    R and D was conducted on original processing technology for electrically functional materials as a R and D project on frontier carbon technology, with the results for fiscal 1999 compiled. In the development of film forming technology using a large morphology control film forming device, the device was introduced this year, with film forming conditions probed. In the development of large size diamond synthesis process, single crystal synthesis and evaluation were carried out using an existing microwave plasma CVD reactor, with a study of design made for the device for obtaining a target 16 mm diameter single crystal. In the development of technology for oriented diamond growth on a platinum-based metallic base plate, research was done for controlling generation of grain boundary in a diamond film, through the improvement of orientation and the reduction of non-oriented grain density of the diamond nucleated on the base plate. The studies on control technology of surface-interface and electron emission characteristics were conducted on such subjects as fabrication technology of diamond for field emission, characterization of field emission, and photoelectron emission spectroscopy of diamond. (NEDO)

  14. Fiscal 1999 achievement report on research and development of industrial technology of new industry creation type. Research and development of intelligent material and structural system (Development of energy use rationalization technology); 1999 nendo chiteki zairyo kozo system no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Fiber or foil shaped sensor materials and actuator devices were integrated with composite materials and composite material structures for processing and controlling information, and then studies were conducted about materials and structural systems for enabling real-time detection of damage in materials and structures, examination of soundness, control of noise and vibration, and the like. Concerning optical fiber sensors in the development of smart manufacturing technologies, the impact imposed on composite materials by sensors embedded therein was investigated, and the scope of their applicability was determined. In the development of actuator materials and devices, ceramic actuators were fabricated by microwave sintering, and it was found that they were higher in performance by 30% than actuators of the conventional design. In the testing of demonstrators, molded body monitor basic tests using optical fiber sensors were conducted for jet engine static vane models, and temperature dependence of optical intensity was understood. (NEDO)

  15. FY 1998 Annual report on research and development of industrial science and technology. R and D of carbon-based high-performance materials technology (R and D for rationalization of energy consumption); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This report summarizes the FY 1998 research and development results of carbon-based high-performance materials technology. For (control technology of morphology and electrical conduction), a large-sized morphology controlling film-making apparatus was used, to confirm synthesis of crystalline diamond films. For research on growth of large-sized single-crystal diamond, the simulated results of the vapor-phase reactions and gas flow in a plasma were compared with the observed ones, to collect the data necessary for designing a high-speed homoepitaxial growth apparatus. For R and D of heteroepitaxial growth of thin diamond films, highly single-crystalline thin platinum films were successfully formed on a sapphire substrate. For (control technology of surface-interface and electron emission characteristics), the tests were conducted using newly introduced apparatuses, an (electron emission analysis/evaluation apparatus), (high-quality carbon-based thin film synthesizing apparatus) and (element processing/treatment apparatus). It is found that electron emission efficiency is greatly improved when the substrate with diamond particle seeds is plasma-treated under specific conditions. (NEDO)

  16. FY 2000 report on the results of the technology development of energy use reduced machine tools, etc. R and D of the environment-friendly grinding machine system; 2000 nendo energy shiyo gorika kosaku kiki nado gijutsu kaihatsu seika hokokusho. Kankyo taiogata kensaku kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted of a grinding machine system of an environmental-friendly type in which no coolant is used or the amount of coolant is reduced, and the FY 2000 results were summed up. As to the ECOLOG grinding newly thought up, the roles were divided: the lubrication into a trace of the vegetable oil supplied onto the grindstone surface, cooling into a trace of the cooling water supplied to the structure, discharge of chips to the cooling water for bed table cleaning. By this, the amount of the cooling water becomes approximately 1/3 of that in the conventional grinding. Concerning the ECOLOG grinding using the usual grindstone, the grinding performance equal to that in the conventional grinding was confirmed. In the study for making the cooling water non-pollutant, the chlorine/sulfur free coolant was developed which includes no chemical substances designated by the PRTR law at all. It was confirmed that the grinding performance was almost the same level as the existing coolant which includes sulfur. In the study of the supply of coolant applied with ultrasonic waves, the result was obtained that in the optical glass grinding, the number of scratches decreased and the surface roughness improved even at the flow rate of coolant which is less than in the conventional grinding. (NEDO)

  17. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research and development of high-quality amorphous silicon film formation technologies using plasma separation); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (plasma bunri ni yoru kohinshitsu amorphous silicon maku seimaku gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    When discharge plasma is applied for film formation, ions affect the quality of the resultant film. In the case of plasma CVD (chemical vapor deposition) method, there exists correspondence between the radicals ratio SiH/H and solar cell conversion efficiency, and plasma measurement may be used for the control of film formation conditions. The state of distribution of radicals in discharge plasma is dependent on the type of radicals, and there is an optimum substrate position. Photoelectric characteristics are improved when a grid electrode is used for plasma separation. The surface of a transparent conductive film (ITO: indium-tin oxide) to be the substrate for film formation needs to be flat, and part of its Si is oxidized into SiO{sub 2} by generated oxygen. An ITO film coated by chemically stable SnO{sub 2} is useful. When the ion plating method is employed, film formation conditions are first selected, and then, in a heat treatment to follow, resistance films of various surface conditions are obtained. Carbon-added a-Si film formation conditions and the relationship between film qualities and solar cell characteristics are elucidated. In a solar cell of the p-i-n structure with an a-Si:C:H film acting as the p-layer, a conversion efficiency of 7.6% is achieved. (NEDO)

  18. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (R and D of the intellectual material and structural systems); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki kozo system no kenkyu kaihatsu (chiteki kozo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, where the fibrous or leafy sensor material or element (muscle) is integrated with a structure of an advanced material (skeleton) to process and control information (brain). The program for development of the health monitoring technologies successfully improves the fine FRG (Fiber Bragg Grating) as the high-performance sensor, equipped with a connector which allows the sensor to be easily connected to the normal diameter one, and develops various prototype sensors. The program for self-diagnosis of structural soundness and controlling damages verifies detection effectiveness of the embedded fine FRG sensor. The impact-related characteristics and damages of the reinforced flat plate are detected by embedding the optical fiber sensor. The program for developing the actuator materials and elements prepares the 20{mu}m thick piezoelectric sheet of adequate strength and toughness by dispersing the PNN-PZT system with partially stabilized zirconia (PSZ). The program for the function-gradient systems prepares the FGM driven at normal temperature, characterized by its structure of more evenly distributed stress, to evaluate its characteristics. It is proved to have high durability. The results of the comprehensive survey are also described. (NEDO)

  19. FY 1999 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (R and D of the intellectual material and structural systems); 1999 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (chiteki zairyo kozo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 1999 results of the R and D project for development of intellectual materials and structural systems, where the fibrous or leafy sensor material or element (muscle) is integrated with a structure of an advanced material (skeleton) to process and control information (brain). The program for development of the health monitoring technologies develops the fine optical fiber (diameter: 40{mu}m), which is on a level with the conventional 125{mu}m-diameter fiber in strength and fatigue characteristics, for the high-performance sensor systems. The self-diagnosis of soundness, e.g., detection of impact loads and damages, is attempted using the fine optical fibers embedded in the composite structures. The program for active-adaptive control of smart structures investigates control of vibration and noise for beam structure elements, using the theoretical model developed for shape memory alloys. The vibration tests are conducted, where a distribution type sensor is used for active-adaptive control of soft structures, and the good results are produced. The program for development of actuator materials and elements produces high-strength, high-toughness PZT and PNN-PZT sheets of uniformly distributed thickness by the doctor blade method. (NEDO).

  20. Report on results of development of fuel cell power generation technology 1998. Research and development on polymer electrolyte fuel cell (technological development of element, research on ion exchange membrane for practicability of high performance cell); 1998 nendo seika hokokusho. Nenryo denchi hatsuden gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, yoso kenkyu kaihatsu (koseino denchi jitsuyoka no tame no ion kokan maku ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper explains the results during fiscal 1998 of ion exchange membranes in the development of polymer electrolyte fuel cells. Studies were made on three kinds of standard and two kinds of experimental membranes selected among the Flemion membranes, which are perfluorosulfonic acid membranes made by Asahi Glass Co.,Ltd., and also on the Nafion membranes by Dupon as reference. As the resistance evaluation of the environmental cycle for the membranes, a temperature cycle test was carried out, with the characteristics measured such as moisture content, membrane resistance, mechanical properties, and gas permeability, so that the effects were examined of the temperature cycle on the membranes. Evaluation was also commenced on the water permeability, an important substance-moving characteristic of ion exchange membranes. In the evaluation of the characteristics of membrane-electrode assemblies, the environmental cycle test was performed by joining electrodes to membranes, with the evaluation similarly made as for the membranes alone. On the basis of a correlation between the water permeability and the cell performance, studies were made on the effect of thickness of the membranes on the cell performances. A continuous stability/durability operation of 3,500 hours was verified using Flemion R. As for membrane reinforcement, studies were continued on the cloth and fibril reinforcements as in the previous year.(NEDO)

  1. Fiscal 1999 survey report. Survey of leading countries' approaches to biomass energy development; 1999 nendo shuyokoku ni okeru biomass energy kaihatsu eno torikumi ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey aims to help Japan deliberate its future biomass energy development strategy including the course Japan is to follow in its research and development of biomass energy by clarifying leading countries' approaches to the subject matter and trends of their research and development efforts in this connection. The states of biomass energy development in the U.S. and Europe are reported. In the U.S., President Clinton issued Executive Order 13134 on August 12, 1999, regarding bio-based products and bioenergy development. In this country, bioenergy and bio-based production technologies have developed to reach a stage where business pays, and commercial plants are in service. The U.S. Administration mentions as a strategy the efficient development of the bioenergy industry. In Europe, where resources are versatile and local, it is difficult to assess the economy of scale, and small-scale development efforts are being accumulated. Practical technologies under development mostly involve direct combustion. European measures are similar to U.S. measures in that such political goals as local development and employment promotion are firmly woven into them. (NEDO)

  2. Reports on 1981 result of Sunshine Project. Research on conditioning required for industrialization of new energy technology (summary); 1981 nendo shin energy gijutsu kigyoka ni hitsuyona joken seibi ni kansuru chosa kenkyu. Yoyakuhen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In order to decide measures for introducing new energy to the society, the work starts from the investigation of the present state of energy demand, examining feasibility of introducing new energy into the state, and then assuming concretely the circumstances in which new energy is brought into the society to some extent. In the subject research, with 1990 set as a target year, the following examinations are carried out for the purpose of estimating the state of introducing new energy to the Japanese society at such point in time. (a) Feasibility is studied of substituting with new energy on oil users' part at present, with an estimate made on the state of new energy introduction in fiscal 1990. (b) An energy flow analysis is made for the purpose of checking interrelation between the total energy demand structure in Japan and the quantity of introducing new energy as of 1990. (c) On the basis of these results, current various energy-related laws and regulations are reviewed, with policies examined for introducing and promoting new energy. (d) On-site investigation is conducted on relationship with the energy policy of coal producing countries, in the case where a coal liquefaction plant is constructed in such countries and where overseas operations and imports of liquefied oil production are implemented. (NEDO)

  3. Fiscal 1994 New Sunshine Program achievement report. Development of industrial solar system practicalization technology - Survey and research on solar system (Survey and research on city-oriented solar technology); 1994 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Solar system no chosa kenkyu (solar toshi muke gijutsu ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Solar technology and energy conservation technology (through retrofitting) which can be introduced into existing buildings are evaluated for their effect and economic efficiency. Studied are technologies verified to be technically feasible at the current stage, introducible into existing buildings without major modification, low in introduction cost, and high in energy conservation effect. How retrofitting technology should be in Japan is discussed. In Japan where demand for heat is smaller than in Europe or America and building service life is shorter, conditions to meet for efficient cost recovery are quite severe. Suitable measures to enhance cost recovery include use of multiple panels of low-radiation glass and light modulators for windows and use of collecting technologies such as solar systems for hot water supply and air solar collectors. Use of a transparent insulator is also recommended. Japanese houses demand repair and reconstruction very often, which helps cost recovery. Dependence on locality is extensive, and this causes difference in solar system application. Since it is high in temperature and humidity in summer in Japan, there is a great need for environmental comfort, and therefore not only energy conservation but also comfortable air-conditioning is important. (NEDO)

  4. Sunshine Program-assisted project achievement report for fiscal 1981 on the development of technologies for photovoltaic power system practical application. Development of photovoltaic power generation demonstration system (Research and development for schoolhouses); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden demonstration system kaihatsu (gakkoyo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Power generated by solar cells complying with NEDO (New Energy and Industrial Technology Development Organization) specifications is stored in a storage battery or is converted into AC power in a DC-AC converter for interconnection with a commercial power system, and then supplied to loads in schoolhouses. The system operates independently when the commercial power system is out. Basic plans and primary specifications had been determined, basic modules experimentally built, tested, and part of their details designed, all these up to fiscal 1980. In fiscal 1981, system design details are drawn, housetops are examined for installation, and problems that may entail installation are checked. A system data accumulation unit comes into operation for data collection. A system simulator is developed and constructed and the solar cell is checked for performance. Model arrays are built and subjected to a combination tests, when the effect of shade is also investigated. A charge control unit, high-efficiency GTO (gate turned-off) thyristor DC-AC converter, and a protection circuit in preparation for interconnection are developed, and experimentally constructed. In fiscal 1982, 20kW solar cells will be installed and schoolhouse systems will come into service operation. (NEDO)

  5. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In relation with several types of standard photovoltaic power generation systems expected to be put to practical use, design parameters are quantified, databases are utilized, and simulation technologies are developed, while collecting data from test facilities constructed to simulate them, for the development of evaluation techniques indispensable for the efficient improvement of photovoltaic power generation systems. In fiscal 1998, data were collected from verification test facilities and residential photovoltaic systems sited across Japan. The collected data were subjected to analysis and simulation, by which correction factors were calculated for smudge, spectral response, incident radiation, and temperature. Furthermore, load matching factors and storage battery contribution rates were calculated by simulation for the stand-alone photovoltaic systems sited in five Japanese cities, each comprising an array, storage battery, charge/discharge controller, DC-DC converter, and a load. Reference is also made to a survey of trends of technology development. (NEDO)

  6. Achievement report for fiscal 1982 on Sunshine Program-entrusted research and development. Survey on patent and information (Hydrogen energy); 1982 nendo tokkyo joho chosa kenkyu seika hokokokusho. Suiso energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    Patents related to the research under the Sunshine Program are surveyed so as to ensure that the program be promoted smoothly and efficiently. Since the scope of the hydrogen energy technology is extensive, branches supposed to be relatively important only are surveyed, which include the production of hydrogen (thermochemical process, photochemical process, and electrolysis), storage and transportation of hydrogen, safety of hydrogen, hydrogen fuel cells, hydrogen-fueled engines, and hydrogen combustion devices. The basic policy to follow in the extraction of necessary patents is that all related to the hydrogen energy technology be collected from as many fields as possible. However, it is impossible to read all the laid-open patents. Under such circumstances, out of the items in IPC (International Patent Classification) used by the Patent Agency, those deemed to be closely related to the hydrogen energy technology are designated and, when the classification item attached to the official gazette matches one of the IPC classification items, it is extracted as a desired item after deliberation of its relationship with the hydrogen energy technology. (NEDO)

  7. FY 2000 report on the project on the researcher dispatch type international joint research survey. Survey of the internationalization of research on the effective utilization technology for energy resources; 2000 nendo kenkyusha hakengata kokusai kyodo kenkyu chosa jigyo hokokusho. Energy shigen yukoriyo gijutsu kenkyu kokusaika chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to themes of the research survey which contribute to upgrading/diversification of the effective utilization of energy resources and are important in increasing cooperative relations with overseas countries, survey research was conducted by dispatching investigators. Relating to long-life Si solar cells, research survey was made on the reduction in deterioration of solar cell. Concerning the hydrogen carbonless energy system, the economical efficiency of a natural energy/hydrogen combined system was studied for all areas of Aomori prefecture. About the development of the multiple chamber type artificial pancreas for patients with serious diabetes, study using model dogs was investigated. As to the processing of PVC waste, the mechano-chemical method was discussed in the U.S. The paper further surveyed the following: PDE application to the aerospace field, joint developmental study of the reuse type space transport system by Japan and Russia, treatment/recycling of the electric/electronic equipment waste including toxic substances, technology of the manufacture of nano-particles and evaluation of optical characteristics of nano-structures, etc. (NEDO)

  8. Fiscal 1998 research report. Survey on development and application of membranes with pores of micron to nano-meter sizes; 1998 nendo chosa kenkyu hokokusho. Makuro kara mikuro (nano mezo dai) size wo motsu, menburenmaku no kaihatsu narabi ni oyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches on preparation of membranes of various materials have been promoted by not systematic technique but separate techniques according to needs of concerned fields. To establish the efficient technique for membranes with pores of required uniform size according to needs of various industries, survey and study were made on process optimization and low-cost production method. Porous membrane is the leading candidate for new separation systems as separation medium in chemical industry, hot gas filtration for energy production and environmental purification engineering. The electrode, separator and gas storage medium of fuel cell vehicles and next-generation batteries require effective porous materials. The workshop on engineering porous materials held in May 1993 confirmed the time of following materials: High-efficiency gas separation membrane, chemical catalytic membrane, fuel cell electrode and absorbent for environmental purification. Development of inorganic membranes more excellent in high-temperature stability, strength, catalytic activity and corrosion resistance than previous polymer membranes is important. (NEDO)

  9. FY1998 research report on the R and D on the production process technology of eco-tailored tribo-materials. R and D on the production process technology of materials controlled in micro-meter order; 1998 nendo eco-tailored tribo-material sosei process gijutsu no kenkyu kaihatsu chosa hokokusho. Micro-meter order de seigyosareta material sosei process gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Combined laser process technology was applied to development of tribo-materials for such various parts as engine cylinder and valve sheet of various outdoor industrial machinery and transport machinery. In fiscal 1998, study was made mainly on the possibility of every laser process for development of tribo-materials with specific structures and compositions controlled in micro-meter order. The obtained principal results are as follows. As for the pulsed laser deposition process to produce wear resistant coatings for small cylinders, thick films were produced efficiently by laser spattering of molten particles using high-pulse energy laser irradiation on targets. As for the cylinder bore surface modification process by spraying and lasering, basic study was made on this process. As for the process to synthesize intermetallic compounds for engine valve sheets, the effect of laser irradiation conditions on surface modification was studied through laser irradiation on Fe{sub 3}Al compounds synthesized by hot press. (NEDO)

  10. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium field / R and D on downsizing technology of machine tools (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / kosaku kikai no downsizing gijutsu ni kansuru kenkyu kaihatsu (daiichi nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The R and D were conducted aiming at downsizing machine tools by combining microfactory technology owned by Mechanical Engineering Laboratory, Agency of Industrial Science and Technology of MITI with fundamental element technology owned by industrial groups of machine tools. In fiscal 1997, as to the study of spindle drum indexing mechanism in making main spindle multiaxial, the following have been finished: the basic study through openness of controller and networks, confirmation of function of the equipment acquired, and initialization of the driver software. Relating to the study on machining conditions of dry machining processing, delivery and installation of cold air machining instrument have been finished. Concerning the optical measurement of spindle radial run-out vectors, a system to make optical no contact measurement of radial direction components of rotation error was constructed with high accuracy pin gauge attached to the work spindle clamp mechanism as a medium. About the study on sensor-based state recognition technology, specifications for various kinds of sensor were decided on. 5 refs., 67 figs., 3 tabs.

  11. Survey and research for the enhancement of large-scale technology development 3. Patent researches on new tasks for development under large-scale project; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 3. Ogata project shinki kaihatsu tema ni kansuru tokkyo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Regarding 'high-speed computation systems for technological use' and 'manganese nodule mining systems,' researches are conducted into technological trends from the viewpoint of patent. As for applications for patents involving the Josephson effect device, there are 79 patents disclosed in Japan, with applications from Japan recording a peak in 1977-1978 and those from overseas in 1974-1975. As for important applicants, IBM distinguishes itself among those overseas while, in Japan, the Nippon Telegraph and Telephone Public Corporation occupies 47%, and Fujitsu, Ltd., 34%. In the case of GaAs-based transistors, businesses in Japan occupies as much as 90% of the applications overwhelming overseas businesses occupying less than 10%. As for the patents on manganese nodule mining systems, 183 Japanese patents are pending, with 88 already granted in America. While the main concern in Japan has transferred from the continuous elevator bucket system of 1971-1974 to the fluid dredge system, the fluid dredge system has consistently been occupying the overpowering majority in America. (NEDO)

  12. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on second term final research and development (first report); Jisesdai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu bunshi bunrimaku zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This study is intended to establish a basic technology for innovative high-efficiency separation membrane materials that can be used in areas in which application of membrane separation has been impossible. The water/ethanol separation membrane (for water selective permeation) and water/acetic acid separation membrane (for water selective permeation) achieved separation coefficient and permeation velocity of the world's highest level. The water/ethanol separation membrane (for ethanol selective permeation), although its separation coefficient is lower than the world's highest performance, has high permeation velocity, providing the performance of the worldwide level as seen from the comprehensive viewpoint. The carbon monoxide/nitrogen separation membrane achieved separation coefficient and permeation velocity of the world's highest level. The oxygen/nitrogen separation membrane requires further enhancement in the permeation velocity and stability. Establishment has been performed on separation technologies for membrane separation of non-water soluble aqueous solutions, optical division by using chiral crown ether, high-performance liquid separation by means of plasma surface treatment, and particle separation. Basic analysis has been advanced also on evaluation technologies for gaseous body separation membrane and liquid separation membrane, of which future progress is expected. (NEDO)

  13. Fiscal 1974 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on metal system materials); 1974 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Kinzokukei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-30

    This report describes the fiscal 1974 research result on metal system materials for solar cooling/heating and hot water supply systems. Study was made on cathodic protection of a roll bond heat collection board promising as Al plane collector. The protection is dependent on sacrificial anode materials. Al-Zn system alloy including minute amounts of In and Sn was effective in protection by transferring natural electrode potential to a base side largely, however, excess addition of In and Sn increased self-corrosion, remaining some issues to be solved. The prototype water flow corrosion test equipment was prepared for corrosion analysis of an Al roll bond collector natural circulation hot water supplier. Preliminary study was made to give selective absorption power (large short-wave absorption and small long-wave radiation from collector surfaces) to a collector. Deposition of Cu, Ni, Co and Sn oxides as black semiconductors into Al anodic oxidation film porous layers by secondary electrolysis was invalid as well as a painting method. Glossy Ni plating onto Al and black Cr and Ni plating onto the surface more elevated solar exposure surface temperature by more than 20% than black painting. (NEDO)

  14. Fiscal 1974 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on glass system materials); 1974 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Glass kei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-26

    This report describes the fiscal 1974 research result on glass system materials of plane collectors for solar cooling/heating. A barrel lens type collector was poorer in efficiency than conventional ones. A one-directional Fresnel lens type one was promising for improvement of solar radiation collection. The prototype In{sub 2}O{sub 3} selective transmission cover glass was prepared by vacuum deposition. Although selective characteristics including a solar transmissivity of 74% and an IR reflectance of 75-80% were obtained, further improvement of more than 10% is necessary. The evaluation results of some collectors are as follows. A vacuum type is poor because of its low efficiency and necessary vacuum sealing. A multi-layer type shows unsatisfactory performance at some temperatures. A glass honeycomb type is most likely because of its uppermost collection efficiency, however, development of production technology of heat-resistant honeycombs and its profitability remain to be solved. A deformed multi-layer type is practical because of its high efficiency, simple structure and low cost. Further improvement of the transmissivity and IR reflectance of cover glass by more than 10% is necessary. (NEDO)

  15. Fiscal 1976 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on glass system materials); 1976 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Glass kei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This report describes the fiscal 1976 research result on solar heat collectors using glass system materials. In fiscal 1976, study was made on improvement of selective transmission films by vacuum deposition and large prototype films, prototype coated glass by chemical treatment and its quality stability, prototype full-scale honeycomb collector, practical heat collection property, and evaluation of some problems. As the study result, characteristics of this selective transmission glass were equivalent to those of the other selective transmission films with a transmissivity of 0.90 and a reflectivity of 0.10. As the study result of production cost by vacuum deposition and resistance heating, the film treatment cost was estimated to be 2,300yen/m{sup 2}. 40 prototype coated glass plates of 1,000 x 1,000 x 3mm, and 300 prototype coated glass pipes of 16mm diameter, 870mm long and 0.6mm thick were prepared for prototype collectors. Two kinds of full-scale collectors prepared by using these selective absorption heat collection plates and coated glass showed favorable performance in heat collection experiment. (NEDO)

  16. Report of fiscal 1997 R and D result on high temperature superconducting flywheel power storage. R and D of manufacture of superconducting magnetic bearing; 1997 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu seika hokokusho. Chodendo denjiki jikuuke no seisaku no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Element technologies were developed for the manufacture of superconducting magnetic bearing (SMB) with the purpose of putting to practical use a 10 MWh class high-temperature superconducting flywheel power storage system. This paper explains the fiscal 1997 results. A {phi} 180 radial type SMB was designed and fabricated that satisfied the rotational strength at 17,200 rpm for a medium-sized model for measuring characteristics. Compared with the bearing made in the preceding year, improvements in the bearing dynamics were contrived such as flux creep, load capacity and rotational loss, with the maximum flux density improved by 30%; however, only a few percent improvement was attained in field uniformity. An SMB characteristics measuring and testing machine was built, with the characteristics measured. It was confirmed that the rotational loss of a control type magnetic bearing and the intrinsic performance of the testing machine were unchanged regardless of the operation/non-operation of the radial type SMB. The characteristics of the {phi} 180 axial bearing were measured by a stationary type bearing constant testing machine made in 1995, which provided a load capacity characteristics curve with the initially set gap as a parameter as well as a minor loop curve and a load capacity. Also obtained were the maximum average bearing pressure and the maximum load capacity. (NEDO)

  17. Report on achievements in fiscal 1999. Research and development of carbon-based high-function material technologies (research and development of ocean bottom petroleum production system); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    As part of the research and development of carbon-based high-function material technologies, research and development has been performed on a material creating technology and a process technology to crease mechanically high-function materials. The former technology performs synthesis by using the electron excited CVD process and the explosion synthesizing process, intended to analyze the structure and properties thereof. It is intended to synthesize nitriding-based carbon films and elucidate their composition and structure by using the mass separation ion beam method and the laser beams. Synthesizing nano tubes by utilizing catalytic reactions, and investigating their properties are intended by using the thermal CVD process, plasma CVD process and arc discharge process. Elucidation is intended on the reaction and production mechanisms of carbon-based materials, theory estimation, structures possessed by the carbon-based materials, and mechanisms to manifest their characteristics. The latter technology relates to the three assignments subjected to a composition inclining film forming technology, a complex shaped film forming and micro processing technology, and a large area film forming technology. It is intended to utilize positively such properties as low friction and wear performance and high-temperature corrosion resistance expected in high-function carbon-based materials including amorphous carbon, diamond and nitrided carbon for the purpose of application to surface protection of movable parts in different industrial machines, and building materials including glasses. (NEDO)

  18. FY 1998 'The New Sunshine Project' leading R and D. Report on the results of the leading R and D of supercritical fluid utilization technology; 1998 nendo 'New Sunshine Keikaku' sendo kenkyu kaihatsu. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The paper reported the FY 1998 achievement of the supercritical fluid utilization leading R and D which started in FY 1997 on a 3-year plan. In the R and D, solvolysis reaction, oxidation reaction and hydrogenation reaction were taken up in the chemical process using supercritical fluid. In the study of solvolysis reaction, the basic data were obtained on decomposition conditions of thermoplastic and thermosetting plastics in supercritical water. Further, concerning the synthesis of environmental friendly type carbonate using CO2, a conversion rate of almost 100% was obtained. About the oxidation reaction, conditions were found out for burning low grade coal in supercritical water without emitting acid gas. This is considered to lead to a possibility of the supercritical water power generation. Relating to the hydrogenation reaction, a study was made on lightening technology of heavy distillate using supercritical water, and the conditions for effective emission of methane and hydrogen were found out. As to the base technology, a study was made of metal materials with high corrosion resistance against supercritical water. (NEDO)

  19. FY 1979 Annual report on Sunshine Project results. Research and development of photovoltaic power generation systems (Research and development of vertically drawn ribbon crystals of silicon); 1979 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Silicon tatehiki ribon kessho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    The efforts in this fiscal year for development of methods for vertically drawing ribbon crystals of silicon are directed to the following items, in order to further improve the techniques for vertically drawing two or more ribbon crystals on a continuous basis, developed in the previous fiscal year: (1) tests of the drawing apparatus, developed in the previous fiscal year, to deepen the techniques for drawing the ribbon crystals, (2) modification of the above apparatus to further develop the apparatus for vertically drawing two or more ribbon crystals on a continuous basis, (3) comparison of drawing a single ribbon crystal, conducted separately, with drawing two or more ribbon crystals, to clarify the problems involved in the latter, and (4) basic investigations on the materials for the furnace internals exposed to high temperature, other than the carbon material used at present. The vertically drawn ribbon crystals of silicon is investigated, based on the results obtained in the previous fiscal year that ribbon crystal quality depends on impurities present therein, mainly for (1) quantitative analysis of the impurity elements present in the ribbon crystal, (2) relationship between impurity elements and characteristics of the solar cells made on a trial basis, and (3) investigations on local concentration of the impurity elements. (NEDO)

  20. Report on the achievements in fiscal 1999. Research and development on a basic technology to apply superconductivity (Research and development on a basic technology to apply superconductivity); 1999 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Chodendo oyo kiban gijutsu kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    The development of a basic technology to improve superconductivity characteristics has performed (1) studies on the high-temperature superconductivity mechanism, (2) studies on the critical current mechanism, and (3) search for materials. In Item (1), composition and temperature dependence were investigated by measuring superconductivity gap and change in the electron state of pseudo gap using photo-electron spectra and Raman scattering spectra. In Item (2), magnetic flux behavior in the vicinity of the irreversible line was investigated on magnetic flux dynamics of Bi2212 by measuring magnetic resistance and magnetization. High viscosity condition having strong magnetic flux liquid zone was discovered. In Item (3), Sr was used in place of Ba as the constituting element, and several new mercury-based superconductors were synthesized successfully by using the high pressure synthesizing method. In developing superconductive bulk materials and wire materials, elucidation was given on (1) an element technology for high magnetic power bulk materials, (2) an element technology for high critical temperature bulk materials, (3) a fundamental technology for manufacturing next generation wire materials, (4) a fundamental technology for manufacturing next generation large current conductors, and (5) growth mechanism in wire material crystals. Development of laminating and processing technologies for superconductive materials has worked on (1) a single crystal substrate technology, (2) a thin film lamination technology, (3) a standard bonding technology, (4) an advanced bonding technology, and (5) a thin film and bond evaluation technology. (NEDO)

  1. Fiscal 1998 R and D report on femtosecond technology (power generation facility monitoring system using high- intensity X-ray pulse); 1998 nendo femuto byo technology no kenkyu kaihatsu (kokido X senb pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report reports the fiscal 1998 R and D result of Femtosecond Technology Research Association (FESTA) supported by NEDO. For creation of industrial basic technologies supporting the advanced information society in the 21st century, ultra-high speed electronics technology including new functions beyond the speed limit of conventional electronics technologies is indispensable. From such viewpoint, this R and D aims at establishment of the basic technology controlling conditions of beams and electrons in a femtosecond (10{sup -15}-10{sup -12} seconds) region. In development of the titled system, this R and D aims at generation of high-intensity X-ray pulse by interaction between femtosecond light pulse and high-density electron beam pulse, and development of measurement technology (non- stop inspection) of high-speed moving objects using such X- ray pulse. In fiscal 1998, this project succeeded in time stabilization of laser oscillators at a 100fs level and generation of low-emittance electron beam pulse through development of ultra-short pulse synchronization, laser stabilization and electron beam pulse generation technologies. (NEDO)

  2. Achievement report for fiscal 2000 on research and development of human cooperating and coexisting robot system. Research and development of rationalization in oil refining system; 2000 nendo ningen kyocho kyozongata robot system kenkyu kaihatsu seika hokokusho. Sekiyu seisei system gorika kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    It is intended to develop a human cooperating and coexisting robot system that can move around freely during operation and shutdown of a oil refining plant to perform different works. This paper describes the achievements in fiscal 2000. With regard to the navigation and maintenance work functions, design was made on the robot induction system and its conception to perform the works after the robot has reached a place of the work. The specifications required for the robot supporting agent were made clear, and the constituting modules were designed to exchange information with the robot. Specifications were compiled for a portable remote operation device intended of operating different vehicles. Investigations were carried out on such protection technologies as interference check and shock absorbing materials to protect the robot platform. A method was developed to acquire posture and motion patterns of a human demonstrator, using only the upper half of the body, from the images captured by a head-mounted camera. Discussions were given on the specifications, systems and image processing algorithms required for vision-navigated autonomous walking, whose practicability was verified. Autonomous walking by means of map-based guidance, and hand operating technologies were also discussed. (NEDO)

  3. Fiscal 2000 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Research and development of smart catheter for omnidirectional diagnosis; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Zenhoi shindan smart catheter no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The aim is to develop a highly reliable device for detecting pathological developments deep inside the body by combining the pulse compression technique used in high performance radars and a quartz fiber. The project also aims to develop a system which, when compared with the conventional method, is capable of higher resolution at a short range and of reaching farther for the same resolution level. To be contrived for the development of a diagnostic catheter which combinedly uses the ultrasonic pulse compression and imaging technology and an optical picture system are a pulse signal reflection mirror for taking in ultrasonic picture data on the front and the sides in the lumen, an ultrasonic micromotor for rotating the mirror, and a high efficiency ultrasonic transducer similar in size to the waveguide for transmitting ultrasonic pulses to a quartz waveguide from outside the body and for receiving reflected signals. An effort is simultaneously exerted to make the diameter smaller of a quartz waveguide to be built in the catheter to provide a signal passage for the ultrasonic imaging system and the optical picture system for the realization of a catheter tip smaller and thinner as a whole. A study is made about a mechanical-electronic control system for easy luminal insertion. (NEDO)

  4. Achievement report for fiscal 1999 on the development of total evaluation research laboratory system for the medical welfare equipment technology research and development project; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu project yo sogo hyoka kenkyu rabo system kaihatsu jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    A laboratory system named above has been developed to propel forward efficiently the efforts to develop medical welfare technologies through close coordination between medicine and engineering. Six laboratories are linked with each other in a network for the realization of an environment in which general support is extended to all the stages of equipment development from basic through clinical assessment. The biomedical engineering laboratory is constituted of various analyzing devices, and is capable of in vitro assessment of bioingredients. The therapeutic laboratory is provided with bioinformation/NMR (nuclear magnetic resonance) measurement equipment, animal surgical operation equipment, etc., and performs the assessment of test animals at the first stage of clinical assessment. The diagnostic laboratory acquires various image data necessary for the development of medical equipment at the same level as that of the site of clinical diagnosis. The intelligent surgical operation room takes in real-time diagnostic images while a surgical operation is under way and, at the same time, assesses surgical devices in the same environment as that of the surgical operation room. The medical information laboratory accumulates medical and image data from the other laboratories, and integrates the accumulated data. The data management center manages the laboratories in a unified way and enables comprehensive assessment and research. (NEDO)

  5. FY 1977 Annual report on Sunshine Project results. Research and development of photovoltaic power generation systems (Research and development of vertically drawn ribbon crystals of silicon); 1977 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Silicon tatehiki ribon kessho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-31

    This project is aimed at establishment of ribbon crystal production techniques and development of photovoltaic power generation systems incorporating the ribbon crystals, in order to greatly reduce cost of photovoltaic power generation systems. The research efforts in this fiscal year is focused on development of the techniques for continuously growing the ribbons, to attain the above goal by accelerating growth of the ribbon crystals in unit time and clarifying, in the early stage, the problems to be solved before commercializing the ribbon crystals for the future solar cells. The major research results are (1) development of the method for vertically drawing ribbon crystals of silicon, and (2) analysis of the vertically drawn ribbon crystals of silicon. For the item (1), the technological development efforts are focused on continuously drawing mechanisms and furnace for continuous drawing, with the structural studies as the center for the former and solution of heat-related problems for the latter, which eventually lead to development of a 800 mm long ribbon crystal passing over the roll. For the item (2), the crystal structure is analyzed by the electron channeling pattern method. The results suggest that use of a p-type substrate can improve average efficiency of the ribbon crystal type solar cell. (NEDO)

  6. Reports on 1979 result of Sunshine Project. R and D on solar cooling/heating and hot-water supply system (R and D on metallic materials ); 1979 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Kinzokukei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-31

    The following technologies were developed for the purpose of materializing various methods of a solar cooling/heating and hot-water supply system using aluminum and other metallic materials: (1) research on improving corrosion resistance of metallic materials for a heat collector plate and (2) research on a selective absorbing film. The results in fiscal 1979 were as follows. (1) A practicality running test for a solar panel, which started in fiscal 1977, was continuously carried out at eight places in the nation. After approximately two years and a half passed, each panel was cut open and analyzed. As a result, despite a difference in the degree of corrosion by the regions, an Al-Zn-Fe-In alloy had a larger corrosion area than two other alloys, but the corrosion depth was shallower, with the corrosion remained only in the clad layer, which seemed to eliminate the fear that it might grow to be a through-hole for the time being. This research was completed. (2) Research for the selective absorbing film was carried out in fiscal 1979 on a chrome black membrane by a high frequency excited ion plating method and on a carbide and nitride membranes. In addition, a durability test and an Auger analysis were performed for a titanium nitride selective absorbing film that was obtained by a DC bipolar reactive ion plating method. (NEDO)

  7. Fiscal 1976 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on metal system materials); 1976 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Kinzokukei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This report describes the fiscal 1976 research result on high-efficiency high-durability inexpensive metallic collectors, equipment and materials for solar cooling/heating and hot water supply systems. In the study on metal materials for heat collector plates, corrosion-proofing experiment was made on Al-Zn, Al-Zn-In and Al-Zn-Fe-In alloys treated by bainite under 7 kinds of environmental conditions, resulting in no formation of any through hole. Study was also made on water flow corrosion test of A1100 material, and water- corrosion retardant for Al. In the study on selective absorption films, study was made on secondary electrochemically coated film and vacuum deposition film. Fabrication, test operation and preliminary experiment were made on the large secondary electrolysis facility for full- scale solar panels. The selective absorptivity of secondary electrochemically coated films was a maximum of 0.95 in absorptivity and 0.10 in emissivity, showing the favorable selective absorptivity of both Ni and Co. The durability test result showed favorable heat resistance, light resistance and moisture resistance. (NEDO)

  8. Industrial and scientific technology research and development project fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Report on research and development of a brain type computer architecture `trial fabrication and high-level evaluation on chips for a large-scale artificial neural system` and on results of evaluation studies on the chips; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Nogata computer architecture no kenkyu kaihatsu `daikibo jinko shinkei kairo system yo chip no shisaku to kodo hyoka` chip hyoka kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop a brain type computer architecture, a brain mimic processor (BMP) has been developed (which was made in LSI in fiscal 1997), and studies are being made on developing its applications. Development has been made on an element in which linkage of one million cells with one thousand neural cells can be realized. Evaluation substrates mounted with the BMP, control software, and compilers were provided to 15 organizations including the National Research Institutes, universities, corporations, and other societies (for 19 themes) to evaluate capability of the LSI and its application development. All of the research organizations are using these items utilizing features of the LSI or the network for such purposes as learning, storage, recognition and control. The applicable theme may include infrared spectrum pattern recognition and domain division of document images using neural network functions. It can also include structural analysis of mass spectrum molecules, time series pattern recognition, location of corresponding points in images, estimation of moving images, satellite control, character recognition, short time storage, long-term association memory models, and invention process studies, all utilizing the functions of the BMP. 71 refs., 89 figs., 9 tabs.

  9. Fiscal 2000 research achievement report on the pioneering research and development involving next-generation liquid crystal process base technologies; 2000 nendo jisedai ekisho process kiban gijutsu ni kakawaru sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the enhancement of energy conservation in the liquid crystal display manufacturing process, activities are conducted in the three fields of (1) low temperature thin film fabrication technology, (2) zone-selective thin film growth technology, and (3) next-generation liquid crystal process base technology and comprehensive surveys. Conducted in field (1) are pioneering studies of low temperature high quality Si film fabrication by electromagnetic annealing, low temperature high quality thin film fabrication by EPA (electron plasma annealing), and low temperature normal pressure film fabrication. Conducted in field (2) are pioneering studies of zone-selective fabrication of high quality Si crystal film, high precision control of reforming (doping), and free pattern low resistance wiring fabrication. Conducted in field (3) are tentative fabrication, evaluation, and analysis of ultimate performance TFTs (thin film transistors) produced by the state-of-the-art purification enhancement technology; next-generation liquid crystal process; and surveys of functional thin film to be a novel material for substrates. In the pioneering study of low temperature high quality Si film fabrication by means of electromagnetic annealing, microwave annealing is studied as an energy efficient process to replace the currently favored ELA (excimer laser annealing) method, and then it is proved that the microwave annealing method is much higher in energy efficiency than the ELA method. (NEDO)

  10. Report on achievements in technological development in fiscal 1999. Development of technology to put photovoltaic power generation system into practical use (Research and development of high reliability storage batteries for photovoltaic power generation use); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (taiyoko hatsuden'yo chikudenchi kaihatsu bukai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Storage batteries used in household photovoltaic systems must be free of electrolyte leakage and maintenance, and be readily installable in residential houses. Lead-acid batteries that can meet these requirements and have been put into practical use may include the sealed storage batteries. However, these batteries currently in use have drawbacks in life performance and price. Therefore, development is under way on lead-acid batteries for household photovoltaic systems by improving said sealed lead-acid batteries. The targeted batteries should have as long life as passing 3,000 cycles under a condition of 0.1 to 1 CA discharge (at depth of discharge of 50%), energy density of more than 70 Wh per liter, and cost of 12 yen or lower per watt-hour. A prototype battery as the final candidate was fabricated, that uses silica powder as the electrolyte retainer (silica powder filled between plates, and into clearance between plate groups), pasted plates made of expanded metal grids for positive plates, and micro conductive network plates with increased addition amount of carbon to micro active material (PbO{sub 2}) as negative plates. Life performance testes thereon are being performed. This lead-acid battery is estimated to be capable of satisfying the intended performance based on the result of discussions having been made so far. (NEDO)

  11. Report on surveys and researches at the New Energy General Development Organization in fiscal 1980. Surveys and researches on hydrogen energy; 1980 nendo suiso energy ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-09-01

    This paper describes surveys and researches on hydrogen energy in fiscal 1980. The high-temperature high-pressure water decomposition process in hydrogen manufacturing technologies had development proceeded on membranes and electrodes, and succeeded operating a 4 Nm{sup 3}/hr plant. Also for the solid electrolyte electrolytic process, a test plant of 1.3 m{sup 3}/hr was completed. The paper describes iodine and bromine system cycle, high-temperature gas atomic reactor cycle, and hybrid process with regard to the thermo-chemical method cycle. Problems in different cycles include necessities to advance the development paying attention on sufficient discussions on thermal efficiency of 35% or higher, heat regeneration and recovery, discussions on separation and transportation, and durability of reactive device materials. The paper also introduces research on hydrogen manufacturing utilizing chemical conversion of solar energy, biomass, and microorganisms. For technologies to store and transport hydrogen, the paper introduces metal hydrides, whereas Ti-based and misch metal-based alloys were found suitable. For transportation, Mg-based alloy hydrides were regarded as the most expected hydrogen absorbing material. Surveys were made also on the current status of the manufacturing industry, production and utilization of hydrogen. (NEDO)

  12. Fiscal 1999 survey report. Survey of leading countries' approaches to biomass energy development; 1999 nendo shuyokoku ni okeru biomass energy kaihatsu eno torikumi ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey aims to help Japan deliberate its future biomass energy development strategy including the course Japan is to follow in its research and development of biomass energy by clarifying leading countries' approaches to the subject matter and trends of their research and development efforts in this connection. The states of biomass energy development in the U.S. and Europe are reported. In the U.S., President Clinton issued Executive Order 13134 on August 12, 1999, regarding bio-based products and bioenergy development. In this country, bioenergy and bio-based production technologies have developed to reach a stage where business pays, and commercial plants are in service. The U.S. Administration mentions as a strategy the efficient development of the bioenergy industry. In Europe, where resources are versatile and local, it is difficult to assess the economy of scale, and small-scale development efforts are being accumulated. Practical technologies under development mostly involve direct combustion. European measures are similar to U.S. measures in that such political goals as local development and employment promotion are firmly woven into them. (NEDO)

  13. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

  14. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

  15. Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects. Solar energy technology research and development; solar panel experiment, manufacture, and verification (Photovoltaic power system practical application technology; ribbon-type crystal substrate process technology); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (ribon kessho kiban kotei no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Carried over from the preceding fiscal year are the development of ribbon crystal pulling technology and the studies of ribbon crystal substrate quality and plant operation. In the development of ribbon crystal pulling process, a pulling drive is built and the limiter mechanism is strengthened for improvement on ribbon crystal flatness, technologies are established for high-speed pulling of broad ribbon crystals, pulling system prototype is built, after-annealing technique is improved for eliminating distortion, and technologies are developed for continuous feeding of raw materials. In the quality examination of ribbon crystal substrates, a method is tested and studied for bringing about a decrease in the number of SiC grains. The object of the plant operation study is a plant capable of producing 250kW-equivalent ribbon crystals a year, and the efforts involve the ribbon pulling system, rough cutter, real-size cutter, etching unit, shape checker, packing, devices for production lines such as warehouses for products, electric power, gas, water, peripheral equipment for waste water treatment etc., ribbon specifications check, quality related assistance equipment to deal with unacceptable products etc., pollution-preventing facilities for the preservation of production environments, and plant buildings. (NEDO)

  16. Achievement report on research and development in the Sunshine Project in fiscal 1978. Surveys and studies on patents and information (Surveys on progress in research and development); 1978 nendo tokkyo joho chosa kenkyu seika hokokusho. Kenkyu kaihatsu suichoku jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    This paper describes the surveys in fiscal 1978 on the status of progress in research and development in the Sunshine Project. Identification, evaluation and analysis were given on the status of progress in research and development and developed technologies in each project. Items of information were provided to related organizations for the purpose of mutual information exchange. The subjects include solar heat power generation, solar beam power generation, solar energy air conditioning, hot water supply systems, geothermal applications, and coals. Project teams were organized to discuss more precise identification of the current status of research and development, and increase in efficiency of the research activities. Since the Sunshine Project (which had begun in 1974) is coming close to completing the interim programs in the first term in fiscal 1980, it is thought necessary to provide assistance such as provision of items of information both for each group and on the collective basis. The basic issues at the end of the first term include presentation of the second term conception to the persons responsible of the program management, clarification of the evaluation criteria, strengthening of horizontal communication and adjustment functions in general, and feeding back of the surveys on the status of progress. Putting the basic problems in individual projects into order indicates necessity of discussion on the voucher control system, procedures of disposing of facilities after the related researches have been completed, issues of creating initial market, and expansion of technological discussions. (NEDO)

  17. Investigational study of evaluation of the global energy system as a global environmental protection technology; Chikyu kankyo taisaku gijutsu toshite no global energy system no hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    With relation to some global energy systems of which viability is predicted in the future, an evaluation was conducted from the viewpoints of economical efficiency, energy balance, CO2 emission, etc. The fossil fuel CO2 capture system, the conventional thermal power plant added with CO2 recovery/treatment facilities, is expected to reduce approximately 70-75% of the CO2 emission. The fossil fuel decarbonated hydrogen system, which decarbonates fossil fuels, recovers/treats CO2 at the place of fuel supply and uses as hydrogen, is of poor practical application from an economical point of view. The fossil fuel methanol synthesis system, which synthesizes methanol from fossil fuels at the place of fuel supply, generates electric power and recovers/treats CO2 with the methanol, is large in energy loss and CO2 emission and low in overall efficiency and CO2 reduction effect at the time of methanol synthesis. The renewable energy hydrogen system is an ultimate system with no emission of CO2, though it costs much. 110 refs., 83 figs., 107 tabs.

  18. Social aspects of Japanese particle physics in the 1950s

    International Nuclear Information System (INIS)

    Konuma, Michiji

    1989-01-01

    Military and social restrictions imposed on Japanese scientific research following the second world war made nuclear or particle physics experiments almost impossible. However, the (Japanese) theoretical achievements of the 1940s considerably buoyed this group, namely two-meson theory, super-many-time theory and covariant renormalization theory. Economic conditions were also difficult with high inflation throughout the 1950s. Printing and distribution problems and paper shortages reduced the circulation of scientific journals, but theoretical work progressed well even in isolation. Within Japan, a circular called Soyrushiron Kenkyu (elementary particle theory research) became a valuable medium for exchange of new ideas and information. A Research Institute for Fundamental Physics, the first of several Japanese research institutes, was opened at Kyoto University in 1953, when a major international conference was held there. The second half of the 1950s was a time of expansion and consolidation for particle physics in Japan. (UK)

  19. NEDO Forum 2001. Session on IT (Opening the door to research and development of the future); NEDO Forum 2001. IT session (kenkyu kaihatsu no mirai wo hiraku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-said session on IT (information technology) of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Visiting Professor Emeritus Makoto Kikuchi of Tokai University in his lecture entitled 'Message to young researchers' cited lessons from the history of semiconductor research and development and stressed the importance of management and of the vitality to be produced by tension at the working place. He predicted that in the future the merit that technologies would present would be valued higher than the development of technologies and that software programs would grow in relative importance. Professor Sakurai of Institute of Industrial Science, University of Tokyo, in his lecture entitled 'What people want from research and development in the future' dealt with propensity for application, coordination of different technologies, and the importance of the internationalization of persons of talent. Chief Engineer Murakami of Sumitomo Electric Industries Ltd. spoke in his lecture, entitled 'Research and development strategy in business corporations,' about corporate consciousness of research and development in Japan, development and use of new scoring methods, and one-sigma management. (NEDO)

  20. Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (total system); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Total system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    For every solar energy utilization field, its background, feasibility, impact in practical use, and R and D policy in Japan were studied. Heating and hot water supply by solar energy are already practical because of less technical problems and reasonable profitability, and cooling is also practical as far as a technical viewpoint. At present, the technical level of solar heat power generation is in the stage of basic technology, however, in the future, development of economically reasonable systems will be demanded as well as establishment of its technology. The most difficult problem for realizing practical solar cell power generation systems is cost reduction. It is also another problem that a big demand of Si for solar cells further exceeds the current yield of Si in a semiconductor industry. A small-scale hybrid solar cell power generation system applicable to the roof of general residences is already feasible. Although a solar furnace is still poor in application to industrial fields, it is expected as the leading part for a future solar heat chemical industry. (NEDO)